WorldWideScience

Sample records for ester terminated alkanethiol

  1. Tribology of monolayer films: comparison between n-alkanethiols on gold and n-alkyl trichlorosilanes on silicon.

    Science.gov (United States)

    Booth, Brandon D; Vilt, Steven G; McCabe, Clare; Jennings, G Kane

    2009-09-01

    This Article presents a quantitative comparison of the frictional performance for monolayers derived from n-alkanethiolates on gold and n-alkyl trichlorosilanes on silicon. Monolayers were characterized by pin-on-disk tribometry, contact angle analysis, ellipsometry, and electrochemical impedance spectroscopy (EIS). Pin-on-disk microtribometry provided frictional analysis at applied normal loads from 10 to 1000 mN at a speed of 0.1 mm/s. At low loads (10 mN), methyl-terminated n-alkanethiolate self-assembled monolayers (SAMs) exhibited a 3-fold improvement in coefficient of friction over SAMs with hydroxyl- or carboxylic-acid-terminated surfaces. For monolayers prepared from both n-alkanethiols on gold and n-alkyl trichlorosilanes on silicon, a critical chain length of at least eight carbons is required for beneficial tribological performance at an applied load of 9.8 mN. Evidence for disruption of chemisorbed alkanethiolate SAMs with chain lengths n tribology wear tracks. The direct comparison between the tribological stability of alkanethiolate and silane monolayers shows that monolayers prepared from n-octadecyl dimethylchlorosilane and n-octadecyl trichlorosilane withstood normal loads at least 30 times larger than those that damaged octadecanethiolate SAMs. Collectively, our results show that the tribological properties of monolayer films are dependent on their internal stabilities, which are influenced by cohesive chain interactions (van der Waals) and the adsorbate-substrate bond.

  2. Gold(I)-Alkanethiolate Nanotubes

    KAUST Repository

    Zhang, Yu Xin; Zeng, Hua Chun

    2009-01-01

    (Figure Presented) A solution approach to assembling Au(I) - alkanethiolates into nanotube structures at room temperature is presented, in which Au(I) cations and alkanethiolate ligands are coordinated into thin platelet forms that then evolve into an open tubular configuration (see figure). The organic-inorganic hybrid nature of the nanotubes, their ability to be modified, and their high stability make them of interest for practical applications. © 2009 WILEY-VCH Verlag GmbH & Co. KGaA.

  3. Gold(I)-Alkanethiolate Nanotubes

    KAUST Repository

    Zhang, Yu Xin

    2009-12-28

    (Figure Presented) A solution approach to assembling Au(I) - alkanethiolates into nanotube structures at room temperature is presented, in which Au(I) cations and alkanethiolate ligands are coordinated into thin platelet forms that then evolve into an open tubular configuration (see figure). The organic-inorganic hybrid nature of the nanotubes, their ability to be modified, and their high stability make them of interest for practical applications. © 2009 WILEY-VCH Verlag GmbH & Co. KGaA.

  4. Self-assembly of alkanethiolates directs sulfur bonding with GaAs(100)

    Energy Technology Data Exchange (ETDEWEB)

    Mancheno-Posso, Pablo; Muscat, Anthony J., E-mail: muscat@email.arizona.edu

    2017-03-01

    Highlights: • Alkanethiolate monolayers were formed on GaAs(100) using a 20 min liquid immersion. • The longest chain containing 20 CH{sub 2} groups protected the surface for 30 min from reoxidation. • A reaction-diffusion model shows that oxygen diffusion through the carbon chains is fast. • Alkanethiolates protect the surface by reducing the reaction rate of oxygen with the surface. • Assembly of the alkane chains directs sulfur atoms to bond to the surface. - Abstract: Molecules that contain linear alkane chains self-assemble on a variety of surfaces changing the degree of wetting, lubricity, and reactivity. We report on the reoxidation of GaAs(100) in air after adsorbing five alkanethiols (C{sub n}H{sub 2n+1}-SH where n = 3, 6, 12, 18, 20) and one alkanedithiol (HS-(CH{sub 2}){sub 8}-SH) deposited from the liquid phase. The alignment of the alkane chains forms a self-assembled layer, however, air diffuses readily through the carbon layer and reaches the surface. The impact of alignment is to improve the bonding of sulfur with the surface atoms which reduces the oxidation rate based on fitting the data to a reaction-diffusion model. The layer thickness and molecular density scale linearly with the number of carbon atoms in the alkane chain. The thickness of the alkanethiolate (RS{sup −}) layer grows by 0.87 ± 0.06 Å for each C atom in the chain and the surface density by 0.13 ± 0.03 molecule per nm{sup 2} per C atom up to a coverage of 5.0 molecules/nm{sup 2} for n = 20 or 0.8 monolayer. The surface coverage increases with length because interactions between methylene (CH{sub 2}) groups in neighboring chains reduce the tilt angle of the molecules with the surface normal. The tight packing yields areas per alkanethiolate as low as 20 Å{sup 2} for n = 20. The amount of C in the layer divided by the chain length is approximately constant up to n = 12 but increases sharply by a factor of 2–4× for n = 18 and 20 based on the C 1s X

  5. Mechanism underlying bioinertness of self-assembled monolayers of oligo(ethyleneglycol)-terminated alkanethiols on gold: protein adsorption, platelet adhesion, and surface forces.

    Science.gov (United States)

    Hayashi, Tomohiro; Tanaka, Yusaku; Koide, Yuki; Tanaka, Masaru; Hara, Masahiko

    2012-08-07

    The mechanism underlying the bioinertness of the self-assembled monolayers of oligo(ethylene glycol)-terminated alkanethiol (OEG-SAM) was investigated with protein adsorption experiments, platelet adhesion tests, and surface force measurements with an atomic force microscope (AFM). In this work, we performed systematic analysis with SAMs having various terminal groups (-OEG, -OH, -COOH, -NH(2), and -CH(3)). The results of the protein adsorption experiment by the quartz crystal microbalance (QCM) method suggested that having one EG unit and the neutrality of total charges of the terminal groups are essential for protein-resistance. In particular, QCM with energy dissipation analyses indicated that proteins absorb onto the OEG-SAM via a very weak interaction compared with other SAMs. Contrary to the protein resistance, at least three EG units as well as the charge neutrality of the SAM are found to be required for anti-platelet adhesion. When the identical SAMs were formed on both AFM probe and substrate, our force measurements revealed that only the OEG-SAMs possessing more than two EG units showed strong repulsion in the range of 4 to 6 nm. In addition, we found that the SAMs with other terminal groups did not exhibit such repulsion. The repulsion between OEG-SAMs was always observed independent of solution conditions [NaCl concentration (between 0 and 1 M) and pH (between 3 and 11)] and was not observed in solution mixed with ethanol, which disrupts the three-dimensional network of the water molecules. We therefore concluded that the repulsion originated from structured interfacial water molecules. Considering the correlation between the above results, we propose that the layer of the structured interfacial water with a thickness of 2 to 3 nm (half of the range of the repulsion observed in the surface force measurements) plays an important role in deterring proteins and platelets from adsorption or adhesion.

  6. Tip-Loading, Force-Dependent Tunneling Behavior in Alkanethiol Self-Assembled Monolayers Studied Through Conducting Atomic Force Microscopy

    International Nuclear Information System (INIS)

    Lee, Min Hyung; Song, Hyun Wook

    2013-01-01

    The force-dependent tunneling transport in metal/alkanethiol/metal junctions was examined using CAFM. Tunneling current and current density through alkanethiol SAMs increased with increasing tip-loading force in CAFM, which suggests that a potential change in geometry of the molecules under the tip loads influences the transport properties of alkanethiol SAMs. Enhanced intermolecular tunneling transport in the tilted molecular configuration under tip-loading effect is likely responsible for such an increase in tunneling current density. We also demonstrated that through-bond tunneling is a more efficient pathway in alkanethiol SAMs than are intermolecular chain-to-chain pathways, by demonstrating a dependence of current density on the associated tunneling distances. We report a tip-loading, force-dependent tunneling behavior in alkanethiol SAMs using CAFM. A variable tip-loading force applies to alkanethiol SAMs with a standard AFM feedback, and current(I)-voltage(V) characteristics are simultaneously measured while varying the loading forces. In particular, we observe how a tip-loading force in CAFM influences the transport properties of alkanethiol SAMs

  7. Hydrophobicity-induced drying transition in alkanethiol self ...

    Indian Academy of Sciences (India)

    Raman Research Institute, C.V. Raman Avenue, Bangalore 560 080, India ... Hydrophobicity; hydrophobic gap; self-assembled monolayer; length scale dependent .... From our work, we find that when the alkanethiol SAM is prepared from a.

  8. Patterned self-assembled monolayers of alkanethiols on copper nanomembranes by submerged laser ablation

    Science.gov (United States)

    Rhinow, Daniel; Hampp, Norbert A.

    2012-06-01

    Self-assembled monolayers (SAMs) of alkanethiols are major building blocks for nanotechnology. SAMs provide a functional interface between electrodes and biomolecules, which makes them attractive for biochip fabrication. Although gold has emerged as a standard, copper has several advantages, such as compatibility with semiconductors. However, as copper is easily oxidized in air, patterning SAMs on copper is a challenging task. In this work we demonstrate that submerged laser ablation (SLAB) is well-suited for this purpose, as thiols are exchanged in-situ, avoiding air exposition. Using different types of ω-substituted alkanethiols we show that alkanethiol SAMs on copper surfaces can be patterned using SLAB. The resulting patterns were analyzed by atomic force microscopy (AFM) and scanning electron microscopy (SEM). Both methods indicate that the intense laser beam promotes the exchange of thiols at the copper surface. Furthermore, we present a procedure for the production of free-standing copper nanomembranes, oxidation-protected by alkanethiol SAMs. Incubation of copper-coated mica in alkanethiol solutions leads to SAM formation on both surfaces of the copper film due to intercalation of the organic molecules. Corrosion-protected copper nanomembranes were floated onto water, transferred to electron microscopy grids, and subsequently analyzed by electron energy loss spectroscopy (EELS).

  9. Synthesis of Alkanethiolate-Capped Metal Nanoparticles Using Alkyl Thiosulfate Ligand Precursors: A Method to Generate Promising Reagents for Selective Catalysis

    Directory of Open Access Journals (Sweden)

    Khin Aye San

    2018-05-01

    Full Text Available Evaluation of metal nanoparticle catalysts functionalized with well-defined thiolate ligands can be potentially important because such systems can provide a spatial control in the reactivity and selectivity of catalysts. A synthetic method utilizing Bunte salts (sodium S-alkylthiosulfates allows the formation of metal nanoparticles (Au, Ag, Pd, Pt, and Ir capped with alkanethiolate ligands. The catalysis studies on Pd nanoparticles show a strong correlation between the surface ligand structure/composition and the catalytic activity and selectivity for the hydrogenation/isomerization of alkenes, dienes, trienes, and allylic alcohols. The high selectivity of Pd nanoparticles is driven by the controlled electronic properties of the Pd surface limiting the formation of Pd–alkene adducts (or intermediates necessary for (additional hydrogenation. The synthesis of water soluble Pd nanoparticles using ω-carboxylate-S-alkanethiosulfate salts is successfully achieved and these Pd nanoparticles are examined for the hydrogenation of various unsaturated compounds in both homogeneous and heterogeneous environments. Alkanethiolate-capped Pt nanoparticles are also successfully synthesized and further investigated for the hydrogenation of various alkynes to understand their geometric and electronic surface properties. The high catalytic activity of activated terminal alkynes, but the significantly low activity of internal alkynes and unactivated terminal alkynes, are observed for Pt nanoparticles.

  10. Electrochemical Properties of Alkanethiol Monolayers Adsorbed on Nanoporous Au Surfaces

    International Nuclear Information System (INIS)

    Chu, Yeon Yi; Seo, Bora; Kim, Jong Won

    2010-01-01

    We investigated the electrochemical properties of alkanethiol monolayers adsorbed on NPG surfaces by cyclic voltammetry and electrochemical impedance spectroscopy, and the results are compared to those on flat Au surfaces. The reductive desorption of alkanethiols on NPG surfaces is observed in more negative potential regions than that on flat Au surfaces due the stronger S-Au interaction on NPG surfaces. While the electron transfer through alkanethiol monolayers on flat Au surfaces occurs via a tunneling process through the monolayer films, the redox species can permeate through the monolayers on NPG surfaces to transfer the electrons to the Au surfaces. The results presented here will help to elucidate the intrinsic electrochemical properties of alkanethiol monolayers adsorbed on curved Au surfaces, particularly on the surface of AuNPs. Self-assembled monolayers (SAMs) of thiolate molecules on Au surfaces have been the subject of intensive research for the last few decades due to their unique physical and chemical properties. The well-organized surface structures of thiolate SAMs with various end-group functionalities can be further utilized for many applications in biology and nanotechnology. In addition to the practical applications, SAMs of thiolate molecules on Au surfaces also provide unique opportunities to address fundamental issues in surface chemistry such as self-organized surface structures, electron transfer behaviors, and moleculesubstrate interactions. Although there have been numerous reports on the fundamental physical and chemical properties of thiolate SAMs on Au surfaces, most of them were investigated on flat Au surfaces, typically on well-defined Au(111) surfaces

  11. Self-assembled monolayers of n-alkanethiols suppress hydrogen evolution and increase the efficiency of rechargeable iron battery electrodes.

    Science.gov (United States)

    Malkhandi, Souradip; Yang, Bo; Manohar, Aswin K; Prakash, G K Surya; Narayanan, S R

    2013-01-09

    Iron-based rechargeable batteries, because of their low cost, eco-friendliness, and durability, are extremely attractive for large-scale energy storage. A principal challenge in the deployment of these batteries is their relatively low electrical efficiency. The low efficiency is due to parasitic hydrogen evolution that occurs on the iron electrode during charging and idle stand. In this study, we demonstrate for the first time that linear alkanethiols are very effective in suppressing hydrogen evolution on alkaline iron battery electrodes. The alkanethiols form self-assembled monolayers on the iron electrodes. The degree of suppression of hydrogen evolution by the alkanethiols was found to be greater than 90%, and the effectiveness of the alkanethiol increased with the chain length. Through steady-state potentiostatic polarization studies and impedance measurements on high-purity iron disk electrodes, we show that the self-assembly of alkanethiols suppressed the parasitic reaction by reducing the interfacial area available for the electrochemical reaction. We have modeled the effect of chain length of the alkanethiol on the surface coverage, charge-transfer resistance, and double-layer capacitance of the interface using a simple model that also yields a value for the interchain interaction energy. We have verified the improvement in charging efficiency resulting from the use of the alkanethiols in practical rechargeable iron battery electrodes. The results of battery tests indicate that alkanethiols yield among the highest faradaic efficiencies reported for the rechargeable iron electrodes, enabling the prospect of a large-scale energy storage solution based on low-cost iron-based rechargeable batteries.

  12. Self-Assembled Monolayers of n-Alkanethiols Suppress Hydrogen Evolution and Increase the Efficiency of Rechargeable Iron Battery Electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Malkhandi, S; Yang, B; Manohar, AK; Prakash, GKS; Narayanan, SR

    2013-01-09

    Iron-based rechargeable batteries, because of their low cost, eco-friendliness, and durability, are extremely attractive for large-scale energy storage. A principal challenge in the deployment of these batteries is their relatively low electrical efficiency. The low efficiency is due to parasitic hydrogen evolution that occurs on the iron electrode during charging and idle stand. In this study, we demonstrate for the first time that linear alkanethiols are very effective in suppressing hydrogen evolution on alkaline iron battery electrodes. The alkanethiols form self-assembled monolayers on the iron electrodes. The degree of suppression of hydrogen evolution by the alkanethiols was found to be greater than 90%, and the effectiveness of the alkanethiol increased with the chain length. Through steady-state potentiostatic polarization studies and impedance measurements on high-purity iron disk electrodes, we show that the self-assembly of alkanethiols suppressed the parasitic reaction by reducing the interfacial area available for the electrochemical reaction. We have modeled the effect of chain length of the alkanethiol on the surface coverage, charge-transfer resistance, and double-layer capacitance of the interface using a simple model that also yields a value for the interchain interaction energy. We have verified the improvement in charging efficiency resulting from the use of the alkanethiols in practical rechargeable iron battery electrodes. The results of battery tests indicate that alkanethiols yield among the highest faradaic efficiencies reported for the rechargeable iron electrodes, enabling the prospect of a large-scale energy storage solution based on low-cost iron-based rechargeable batteries.

  13. Effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer on Au(1 1 1)

    Energy Technology Data Exchange (ETDEWEB)

    Xi Luan [Surface Science Western, University of Western Ontario, London, Ontario N6A 5B7 (Canada); Zheng Zhi; Lam, N.-S. [Department of Physics, Chinese University of Hong Kong, Shatin, Hong Kong (China); Grizzi, Oscar [Centro Atomico Bariloche, 8400 San Carlos de Bariloche, Rio Negro (Argentina); Lau, W.-M. [Surface Science Western, University of Western Ontario, London, Ontario N6A 5B7 (Canada)], E-mail: llau22@uwo.ca

    2007-10-31

    The effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer (SAM) on Au(1 1 1) are studied with scanning tunneling microscopy (STM) and X-ray photoemission spectroscopy (XPS). The STM and XPS results show that proton bombardment with proton energy as low as 2 eV can induce cross-linking of the adsorbed alkanethiols and transform the original ordered SAM lattice to an array of nanoclusters of the cross-linked alkanethiols. For a bombardment at 3 eV with a fluence of 3x10{sup 15} cm{sup -2}, the typical cluster size is about 5 nm. In addition, the cluster size distribution is narrow, with no cluster larger than 8 nm. The cluster growth can be promoted by increasing the fluence at a fixed bombardment energy or increasing the energy at a fixed fluence. This indicates that surface diffusion of alkanethiols and cluster growth can be harnessed by the control of the bombardment energy and fluence.

  14. Effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer on Au(1 1 1)

    International Nuclear Information System (INIS)

    Xi Luan; Zheng Zhi; Lam, N.-S.; Grizzi, Oscar; Lau, W.-M.

    2007-01-01

    The effects of hyperthermal proton bombardment on alkanethiol self-assembled monolayer (SAM) on Au(1 1 1) are studied with scanning tunneling microscopy (STM) and X-ray photoemission spectroscopy (XPS). The STM and XPS results show that proton bombardment with proton energy as low as 2 eV can induce cross-linking of the adsorbed alkanethiols and transform the original ordered SAM lattice to an array of nanoclusters of the cross-linked alkanethiols. For a bombardment at 3 eV with a fluence of 3x10 15 cm -2 , the typical cluster size is about 5 nm. In addition, the cluster size distribution is narrow, with no cluster larger than 8 nm. The cluster growth can be promoted by increasing the fluence at a fixed bombardment energy or increasing the energy at a fixed fluence. This indicates that surface diffusion of alkanethiols and cluster growth can be harnessed by the control of the bombardment energy and fluence

  15. Manipulation of charge carrier injection into organic field-effect transistors by self-assembled monolayers of alkanethiols

    NARCIS (Netherlands)

    Asadi, Kamal; Gholamrezaie, Fatemeh; Smits, Edsger C. P.; Blom, Paul W. M.; de Boer, Bert

    2007-01-01

    Charge carrier injection into two semiconducting polymers is investigated in field-effect transistors using gold source and drain electrodes that are modified by self-assembled monolayers of alkanethiols and perfluorinated alkanethiols. The presence of an interfacial dipole associated with the

  16. The Porter-Whitesides Discrepancy: Revisiting Odd-Even Effects in Wetting Properties of n-Alkanethiolate SAMs

    Directory of Open Access Journals (Sweden)

    Zhengjia Wang

    2015-12-01

    Full Text Available This review discusses the Porter-Whitesides discrepancy in wetting properties of n-alkanethiolate self-assembled monolayers (SAMs. About 25 years ago, Whitesides and coworker failed to observe any odd-even effect in wetting, however, Porter and his coworker did, albeit in select cases. Most previous studies agreed with Whitesides’ results, suggesting the absence of the odd-even effect in hydrophobicity of n-alkanethiolate SAMs. Recent reports have, however, found the odd-even effect in hydrophobicity of n-alkanethiolate SAMs on smooth substrates, indicating that hydrophobicity, and analogous interfacial properties, of n-alkanethiolate SAMs significantly depends on the properties of substrate. Unfortunately, the Whitesides and Porter papers do not report on the quality of the surfaces used. Based on recent work, we inferred that the original discrepancy between Whitesides and Porter can be attributed to the quality of the surface. Odd-even effect of SAMs in charge transport, capacitance, friction, and SAM structure are also discussed in this review to inform the general discussion. The discrepancy between Porter's group and Whitesides’ group could be due to surface roughness, morphology, oxidation, and adventitious contaminants.

  17. Controlling noncovalent interactions between a lysine-rich α-helical peptide and self-assembled monolayers of alkanethiols on Au through functional group diversity

    Energy Technology Data Exchange (ETDEWEB)

    Raigoza, Annette F.; Onyirioha, Kristeen; Webb, Lauren J., E-mail: lwebb@cm.utexas.edu

    2017-02-28

    Highlights: • Functional variety in SAMs control covalent binding of proteins to surfaces. • Peptide density on Au(111) surfaces controlled by SAM functional groups. • Affinity between biomolecule and SAM surface follows a Langmuir isotherm. • Surface chemistry can mimic functional group diversity in proteins and peptides. - Abstract: Reliably attaching a structured biomolecule to an inorganic substrate would enable the preparation of surfaces that incorporate both biological and inorganic functions and structures. To this end, we have previously developed a procedure using the copper(I)-catalyzed click reaction to tether synthetic α-helical peptides carrying two alkyne groups to well-ordered alkanethiol self-assembled monolayers (SAM) on a Au(111) surface, in which the SAM is composed of a mixture of methyl and azide termination. Proteins, however, are composed of many diverse functional groups, and this composition directly effects protein structure, interactions, and reactivity. Here, we explore the utility of mixed SAMs with alternative terminating functional groups to tune and direct the reactivity of the surface through noncovalent peptide-surface interactions. We study both polar surfaces (OH-terminated) and charged surfaces (COOH- and NH{sub 3}-terminated, which are negatively and positively charged, respectively, under our reaction conditions). Surfaces were functionalized with a bipolar peptide composed of Lys and Leu residues that could express different interactions through either hydrophilic and/or charge (Lys) or hydrophobic (Leu) influences. X-ray photoelectron spectroscopy (XPS) and surface infrared spectroscopy were used to characterize surfaces at all stages of the peptide functionalization procedure. This strategy resulted in a high density of surface-bound α-helices without aggregation. Mixed SAMs that included a positively charged alkanethiol along with the azide-terminated thiol resulted in a more efficient reaction and better

  18. Controlling noncovalent interactions between a lysine-rich α-helical peptide and self-assembled monolayers of alkanethiols on Au through functional group diversity

    International Nuclear Information System (INIS)

    Raigoza, Annette F.; Onyirioha, Kristeen; Webb, Lauren J.

    2017-01-01

    Highlights: • Functional variety in SAMs control covalent binding of proteins to surfaces. • Peptide density on Au(111) surfaces controlled by SAM functional groups. • Affinity between biomolecule and SAM surface follows a Langmuir isotherm. • Surface chemistry can mimic functional group diversity in proteins and peptides. - Abstract: Reliably attaching a structured biomolecule to an inorganic substrate would enable the preparation of surfaces that incorporate both biological and inorganic functions and structures. To this end, we have previously developed a procedure using the copper(I)-catalyzed click reaction to tether synthetic α-helical peptides carrying two alkyne groups to well-ordered alkanethiol self-assembled monolayers (SAM) on a Au(111) surface, in which the SAM is composed of a mixture of methyl and azide termination. Proteins, however, are composed of many diverse functional groups, and this composition directly effects protein structure, interactions, and reactivity. Here, we explore the utility of mixed SAMs with alternative terminating functional groups to tune and direct the reactivity of the surface through noncovalent peptide-surface interactions. We study both polar surfaces (OH-terminated) and charged surfaces (COOH- and NH_3-terminated, which are negatively and positively charged, respectively, under our reaction conditions). Surfaces were functionalized with a bipolar peptide composed of Lys and Leu residues that could express different interactions through either hydrophilic and/or charge (Lys) or hydrophobic (Leu) influences. X-ray photoelectron spectroscopy (XPS) and surface infrared spectroscopy were used to characterize surfaces at all stages of the peptide functionalization procedure. This strategy resulted in a high density of surface-bound α-helices without aggregation. Mixed SAMs that included a positively charged alkanethiol along with the azide-terminated thiol resulted in a more efficient reaction and better alignment

  19. Interpenetrating polymer networks based on cyanate ester and fluorinated ethynyl-terminated imide oligomers

    Directory of Open Access Journals (Sweden)

    Y. Wen

    2017-12-01

    Full Text Available Highly soluble fluorinated ethynyl-terminated imide (FETI oligomers were prepared via a conventional one-step method in m-cresol, using 4, 4′-(hexafluoroisopropylidene diphthalic anhydride and 2, 2′-bis(trifluoromethyl benzidine as the monomers, and ethynylphthalic anhydride as the end-capper; then interpenetrating polymer networks (IPN were formulated from FETI oligomers and bisphenol A dicyanate ester (BADCy through a solvent-free procedure, and their thermal, mechanical, and dielectric properties were fully characterized. The curing mechanism was studied by model reactions using nitrogen nuclear magnetic resonance. As evidenced by differential scanning calorimetry analysis and rheological measurements, the FETI/BADCy blends exhibited lower curing temperature and shorter gelation time in comparison with pure BADCy due to the catalytic effects of ethynyl and residue amic acid groups. The properties of IPNs were fully compared with those of polycyanurate, and the results revealed that the incorporation of FETI into cyanate ester resins could significantly improve the toughness, glass transition temperatures, mechanical and dielectric properties of the resultant IPNs.

  20. Dynamic monolayer gradients: Active spatiotemporal control of alkanethiol coatings on thin gold films

    Energy Technology Data Exchange (ETDEWEB)

    Terrill, R.H.; Balss, K.M.; Zhang, Y.; Bohn, P.W.

    2000-02-09

    The chemical modification of coinage metal surfaces with {omega}-functionalized alkanethiols has proven to be a popular system for studies of wetting, adhesion, chemical affinity, and electron transfer. Varying the composition of binary hydrophilic-hydrophobic self-assembled monolayers (SAMs) can vary the wetting properties of a surface in a continuous manner, a fact that has been exploited to distribute surface-active molecules inhomogeneously under mass-transport control. One goal of these experiments is to create surfaces which permit supermolecular objects to be manipulated under external control, as recently demonstrated at air-liquid interfaces. The authors report chemical potential distributions of alkanethiols, which can be manipulated in both space and time under active electrochemical control.

  1. Effect of alkyl chain length in the terminal ester group on mesomorphic properties of new chiral lactic acid derivatives

    Czech Academy of Sciences Publication Activity Database

    Kohout, M.; Bubnov, Alexej; Šturala, J.; Novotná, Vladimíra; Svoboda, J.

    2016-01-01

    Roč. 43, č. 10 (2016), s. 1472-1485 ISSN 0267-8292 R&D Projects: GA MŠk(CZ) LD14007 Institutional support: RVO:68378271 Keywords : chiral liquid crystal * lactic acid derivative * terminal ester group * mesomorphic properties * dielectric spectroscopy * layer shrinkage Subject RIV: JJ - Other Materials Impact factor: 2.661, year: 2016

  2. Unusual mechanism for the short-range electron transfer within gold-alkanethiol-ionic-liquid films of subnanometer thickness

    International Nuclear Information System (INIS)

    Khoshtariya, Dimitri E.; Dolidze, Tina D.; Eldik, Rudi van

    2009-01-01

    Exploiting nanoscopically tunable composite gold-alkanethiol-ionic-liquid/ferrocene self-assembled systems with tunable electron transfer distance, we discovered in the case of thinner alkanethiol films a thermally activated electron transfer pattern totally controlled by the viscosity-related slow relaxation mode(s) of the ionic liquid acting as the reactant's fluctuating environment. This pattern manifested through the activation enthalpy and volume parameters that are identical to those for viscous flow was explained in terms of the extreme adiabatic mechanism with a vanishing Marcus barrier (via the exponential Franck-Condon-like term approaching unity).

  3. Evaluation on corrosively dissolved gold induced by alkanethiol monolayer with atomic absorption spectroscopy

    International Nuclear Information System (INIS)

    Cao Zhong; Zhang Ling; Guo Chaoyan; Gong Fuchun; Long Shu; Tan Shuzhen; Xia Changbin; Xu Fen; Sun Lixian

    2009-01-01

    We have monitored a gold corrosive dissolution behavior accompanied in n-alkanethiol like n-dodecanethiol assembled process with in situ quartz crystal microbalance (QCM), and then observed it with atomic force microscopy (AFM) which showed an evident image of corrosive defects or holes produced on gold substrate, corresponding to gold dissolution induced by the alkanethiol molecules in the presence of oxygen. For detection of the dissolved gold defects during alkanethiol assembled process, an atomic absorption spectroscopy (AAS) has been carried out in this paper, and the detection limit for the dissolved gold could be evaluated to be 15.4 ng/mL. The amount of dissolved gold from the substrates of gold plates as functions of immersion time, acid media, solvents and thiol concentration has been examined in the oxygen saturated solutions. In comparison with in situ QCM method, the kinetics behavior of the long-term gold corrosion on the gold plates in 1.0 mmol/L of n-dodecanethiol solution determined with AAS method was a slow process, and its corrosion rate on gold dissolution could be evaluated to be about 4.4 x 10 -5 ng.cm -2 .s -1 , corresponding to 1.3 x 10 8 Au atoms.cm -2 .s -1 , that was much smaller than that of initial rate monitored with in situ QCM. Both kinetics equations obtained with QCM and AAS showed a consistent corrosion behavior on gold surfaces.

  4. Template-Directed Self-Assembly of Alkanethiol Monolayers: Selective Growth on Preexisting Monolayer Edges

    NARCIS (Netherlands)

    Sharpe, R.B.A.; Burdinski, Dirk; Huskens, Jurriaan; Zandvliet, Henricus J.W.; Reinhoudt, David; Poelsema, Bene

    2007-01-01

    Self-assembled monolayers were investigated for their suitability as two-dimensional scaffolds for the selective growth of alkanethiol edge structures. Heterostructures with chemical contrast could be grown, whose dimensions were governed by both the initial pattern sizes and the process time.

  5. Fabrication of biomembrane-like films on carbon electrodes using alkanethiol and diazonium salt and their application for direct electrochemistry of myoglobin.

    Science.gov (United States)

    Anjum, Saima; Qi, Wenjing; Gao, Wenyue; Zhao, Jianming; Hanif, Saima; Aziz-Ur-Rehman; Xu, Guobao

    2015-03-15

    Alkanethiols generally form self-assembled monolayers on gold electrodes and the electrochemical reduction of aromatic diazonium salts is a popular method for the covalent modification of carbon. Based on the reaction of alkanethiol with aldehyde groups covalently bound on carbon surface by the electrochemical reduction of aromatic diazonium salts, a new strategy for the modification of carbon electrodes with alkanethiols has been developed. The modification of carbon surface with aldehyde groups is achieved by the electrochemical reduction of aromatic diazonium salts in situ electrogenerated from a nitro precursor, p-nitrophenylaldehyde, in the presence of nitrous acid. By this way, in situ electrogenerated p-aminophenyl aldehyde from p-nitrophenylaldehyde immediately reacts with nitrous acid, effectively minimizing the side reaction of amine groups and aldehyde groups. The as-prepared alkanethiol-modified glassy carbon electrode was further used to make biomembrane-like films by casting didodecyldimethylammonium bromide on its surface. The biomembrane-like films enable the direct electrochemistry of immobilized myoglobin for the detection of hydrogen peroxide. The response is linear over the range of 1-600μM with a detection limit of 0.3μM. Copyright © 2014 Elsevier B.V. All rights reserved.

  6. Change of cobalt magnetic anisotropy and spin polarization with alkanethiolates self-assembled monolayers

    International Nuclear Information System (INIS)

    Campiglio, Paolo; Breitwieser, Romain; Repain, Vincent; Guitteny, Solène; Chacon, Cyril; Bellec, Amandine; Lagoute, Jérôme; Girard, Yann; Rousset, Sylvie; Sassella, Adele; Imam, Mighfar; Narasimhan, Shobhana

    2015-01-01

    We demonstrate that the deposition of a self-assembled monolayer of alkanethiolates on a 1 nm thick cobalt ultrathin film grown on Au(111) induces a spin reorientation transition from in-plane to out-of-plane magnetization. Using ab initio calculations, we show that a methanethiolate layer changes slightly both the magnetocrystalline and shape anisotropy, both effects almost cancelling each other out for a 1 nm Co film. Finally, the change in hysteresis cycles upon alkanethiolate adsorption could be assigned to a molecular-induced roughening of the Co layer, as shown by STM. In addition, we calculate how a methanethiolate layer modifies the spin density of states of the Co layer and we show that the spin polarization at the Fermi level through the organic layer is reversed as compared to the uncovered Co. These results give new theoretical and experimental insights for the use of thiol-based self-assembled monolayers in spintronic devices. (paper)

  7. Studying electron transfer through alkanethiol self-assembled monolayers on a hanging mercury drop electrode using potentiometric measurements.

    Science.gov (United States)

    Cohen-Atiya, Meirav; Mandler, Daniel

    2006-10-14

    A new approach based on measuring the change of the open-circuit potential (OCP) of a hanging mercury drop electrode (HMDE), modified with alkanethiols of different chain length conducted in a solution containing a mixture of Ru(NH3)6(2+) and Ru(NH3)6(3+) is used for studying electron transfer across the monolayer. Following the time dependence of the OCP allowed the extraction of the kinetic parameters, such as the charge transfer resistance (R(ct)) and the electron transfer rate constant (k(et)), for different alkanethiol monolayers. An electron tunneling coefficient, beta, of 0.9 A(-1) was calculated for the monolayers on Hg.

  8. Surface characterization of sulfur and alkanethiol self-assembled monolayers on Au(111)

    International Nuclear Information System (INIS)

    Vericat, C; Vela, M E; Benitez, G A; Gago, J A Martin; Torrelles, X; Salvarezza, R C

    2006-01-01

    In the last two decades surface science techniques have decisively contributed to our present knowledge of alkanethiol self-assembled monolayers (SAMs) on solid surfaces. These organic layers have been a challenge for surface scientists, in particular because of the soft nature of the organic material (which can be easily damaged by irradiation), the large number of atoms present in the molecules, and the complex physical chemistry involved in the self-assembly process. This challenge has been motivated by the appealing technological applications of SAMs that cover many fields of the emerging area of nanotechnology. Sulfur (S) is closely related to alkanethiols and can be used to understand basic aspects of the surface structure of SAMs. In this review we focus on the atomic/molecular structures of S-containing SAMs on Au(111). Particular emphasis is given to the substrate, adsorption sites, chemical state of the S-metal bond and also to the experimental and theoretical tools used to study these structures at the atomic or molecular levels. (topical review)

  9. Surface characterization of sulfur and alkanethiol self-assembled monolayers on Au(111)

    Energy Technology Data Exchange (ETDEWEB)

    Vericat, C [Instituto de Investigaciones FisicoquImicas Teoricas y Aplicadas (INIFTA), Universidad Nacional de La Plata-CONICET, Sucursal 4 Casilla de Correo 16 (1900) La Plata (Argentina); Vela, M E [Instituto de Investigaciones FisicoquImicas Teoricas y Aplicadas (INIFTA), Universidad Nacional de La Plata-CONICET, Sucursal 4 Casilla de Correo 16 (1900) La Plata (Argentina); Benitez, G A [Instituto de Investigaciones FisicoquImicas Teoricas y Aplicadas (INIFTA), Universidad Nacional de La Plata-CONICET, Sucursal 4 Casilla de Correo 16 (1900) La Plata (Argentina); Gago, J A Martin [Centro de AstrobiologIa (CSIC-INTA), 28850 Torrejon de Ardoz Madrid (Spain); Torrelles, X [Instituto de Ciencia de Materiales de Barcelona (ICMAB), Barcelona (Spain); Salvarezza, R C [Instituto de Investigaciones FisicoquImicas Teoricas y Aplicadas (INIFTA), Universidad Nacional de La Plata-CONICET, Sucursal 4 Casilla de Correo 16 (1900) La Plata (Argentina)

    2006-12-06

    In the last two decades surface science techniques have decisively contributed to our present knowledge of alkanethiol self-assembled monolayers (SAMs) on solid surfaces. These organic layers have been a challenge for surface scientists, in particular because of the soft nature of the organic material (which can be easily damaged by irradiation), the large number of atoms present in the molecules, and the complex physical chemistry involved in the self-assembly process. This challenge has been motivated by the appealing technological applications of SAMs that cover many fields of the emerging area of nanotechnology. Sulfur (S) is closely related to alkanethiols and can be used to understand basic aspects of the surface structure of SAMs. In this review we focus on the atomic/molecular structures of S-containing SAMs on Au(111). Particular emphasis is given to the substrate, adsorption sites, chemical state of the S-metal bond and also to the experimental and theoretical tools used to study these structures at the atomic or molecular levels. (topical review)

  10. Etchant-free graphene transfer using facile intercalation of alkanethiol self-assembled molecules at graphene/metal interfaces.

    Science.gov (United States)

    Ohtomo, Manabu; Sekine, Yoshiaki; Wang, Shengnan; Hibino, Hiroki; Yamamoto, Hideki

    2016-06-02

    We report a novel etchant-free transfer method of graphene using the intercalation of alkanethiol self-assembled monolayers (SAMs) at the graphene/Cu interfaces. The early stage of intercalation proceeds through graphene grain boundaries or defects within a few seconds at room temperature until stable SAMs are formed after a few hours. The formation of SAMs releases the compressive strain of graphene induced by Cu substrates and make graphene slightly n-doped due to the formation of interface dipoles of the SAMs on metal surfaces. After SAM formation, the graphene is easily delaminated off from the metal substrates and transferred onto insulating substrates. The etchant-free process enables us to decrease the density of charged impurities and the magnitude of potential fluctuation in the transferred graphene, which suppress scattering of carriers. We also demonstrate the removal of alkanethiol SAMs and reuse the substrate. This method will dramatically reduce the cost of graphene transfer, which will benefit industrial applications such as of graphene transparent electrodes.

  11. Shape-controlled synthesis of NIR absorbing branched gold nanoparticles and morphology stabilization with alkanethiols

    International Nuclear Information System (INIS)

    Van de Broek, B; Frederix, F; Bonroy, K; Jans, H; Jans, K; Borghs, G; Maes, G

    2011-01-01

    Gold nanoparticles are ideal candidates for clinical applications if their plasmon absorption band is situated in the near infrared region (NIR) of the electromagnetic spectrum. Various parameters, including the nanoparticle shape, strongly influence the position of this absorption band. The aim of this study is to produce stabilized NIR absorbing branched gold nanoparticles with potential for biomedical applications. Hereto, the synthesis procedure for branched gold nanoparticles is optimized varying the different synthesis parameters. By subsequent electroless gold plating the plasmon absorption band is shifted to 747.2 nm. The intrinsic unstable nature of the nanoparticles' morphology can be clearly observed by a spectral shift and limits their use in real applications. However, in this article we show how the stabilization of the branched structure can be successfully achieved by exchanging the initial capping agent for different alkanethiols and disulfides. Furthermore, when using alkanethiols/disulfides with poly(ethylene oxide) units incorporated, an increased stability of the gold nanoparticles is achieved in high salt concentrations up to 1 M and in a cell culture medium. These achievements open a plethora of opportunities for these stabilized branched gold nanoparticles in nanomedicine.

  12. Synthesis of amide-functionalized cellulose esters by olefin cross-metathesis.

    Science.gov (United States)

    Meng, Xiangtao; Edgar, Kevin J

    2015-11-05

    Cellulose esters with amide functionalities were synthesized by cross-metathesis (CM) reaction of terminally olefinic esters with different acrylamides, catalyzed by Hoveyda-Grubbs 2nd generation catalyst. Chelation by amides of the catalyst ruthenium center caused low conversions using conventional solvents. The effects of both solvent and structure of acrylamide on reaction conversion were investigated. While the inherent tendency of acrylamides to chelate Ru is governed by the acrylamide N-substituents, employing acetic acid as a solvent significantly improved the conversion of certain acrylamides, from 50% to up to 99%. Homogeneous hydrogenation using p-toluenesulfonyl hydrazide successfully eliminated the α,β-unsaturation of the CM products to give stable amide-functionalized cellulose esters. The amide-functionalized product showed higher Tg than its starting terminally olefinic counterpart, which may have resulted from strong hydrogen bonding interactions of the amide functional groups. Copyright © 2015 Elsevier Ltd. All rights reserved.

  13. Mechanical and charge transport properties of alkanethiol self-assembled monolayers on Au (111) surface: The Role of Molecular Tilt

    Energy Technology Data Exchange (ETDEWEB)

    Mulleregan, Alice; Qi, Yabing; Ratera, Imma; Park, Jeong Y.; Ashby, Paul D.; Quek, Su Ying; Neaton, J. B.; Salmeron, Miquel

    2007-11-12

    The relationship between charge transport and mechanical properties of alkanethiol self-assembled monolayers (SAM) on Au(111) films has been investigated using an atomic force microscope with a conductive tip. Molecular tilts induced by the pressure applied by the tip cause stepwise increases in film conductivity. A decay constant {beta} = 0.57 {+-} 0.03 {angstrom}{sup -1} was found for the current passing through the film as a function of tip-substrate separation due to this molecular tilt. This is significantly smaller than the value of {approx} 1 {angstrom}{sup -1} found when the separation is changed by changing the length of the alkanethiol molecules. Calculations indicate that for isolated dithiol molecules S-bonded to hollow sites, the junction conductance does not vary significantly as a function of molecular tilt. The impact of S-Au bonding on SAM conductance is discussed.

  14. Exploring the Tilt-Angle Dependence of electron tunneling across Molecular junction of Self-Assembled Alkanethiols

    DEFF Research Database (Denmark)

    Frederiksen, Thomas; Munuera, C.; Ocal, C.

    2009-01-01

    Electronic transport mechanisms in molecular junctions are investigated by a combination of first-principles calculations and current−voltage measurements of several well-characterized structures. We study self-assembled layers of alkanethiols grown on Au(111) and form tunnel junctions...... for the longer molecular chains. Our calculations confirm the observed trends and explain them as a result of two mechanisms, namely, a previously proposed intermolecular tunneling enhancement as well as a hitherto overlooked tilt-dependent molecular gate effect....

  15. Tandem Carbocupration/Oxygenation of Terminal Alkynes

    Science.gov (United States)

    Zhang, Donghui; Ready, Joseph M.

    2008-01-01

    A direct and general synthesis of α-branched aldehydes and their enol derivatives is described. Carbocupration of terminal alkynes and subsequent oxygenation with lithium tert-butyl peroxide generates a metallo-enolate. Trapping with various electrophiles provides α-branched aldehydes or stereo-defined trisubstituted enol esters or silyl ethers. The tandem carbocupration/oxygenation tolerates alkyl and silyl ethers, esters and tertiary amines. The reaction is effective with organocopper complexes derived from primary, secondary and tertiary Grignard reagents and from n-butyllithium. PMID:16321021

  16. Click functionalization of phenyl-capped bithiophene on azide-terminated self-assembled monolayers

    International Nuclear Information System (INIS)

    Zheng, Yijun; Cui, Jiaxi; Ikeda, Taichi

    2015-01-01

    Graphical abstract: - Highlights: • Electrochemically-active self-assembled monolayers with phenyl-capped bithiophene were prepared. • Post-functionalization method based on click chemistry solved the solubility issue of phenyl-capped thiophene alkanethiol. • The capture and release of the counter anions during the redox reaction were detectable by E-QCM. - Abstract: We immobilized tetra(ethylene glycol)-substituted phenyl-capped bithiophene with alkyne terminals (Ph2TPh-alkyne) on azide-terminated self-assembled monolayers (N 3 -SAMs) by Cu-catalyzed azide-alkyne cycloaddition reaction. Ph2TPh-functionalized SAMs on a gold substrate showed reversible electrochemical response. The surface densities of the azide groups in N 3 -SAMs and Ph2TPh units in Ph2TPh-functionalized SAMs were estimated to be 7.3 ± 0.3 × 10 −10 mol cm −2 and 4.6 ± 0.3 × 10 −10 mol cm −2 , respectively, by quartz crystal microbalance (QCM). Most of Ph2TPh-alkynes are considered to be anchored on N 3 -SAMs via both terminal groups. Ph2TPh-functionalized SAMs exhibited reversible redox peaks in cyclic voltammetry (CV). In redox reaction, reversible capture and release of the counter anion could be monitored by electrochemical QCM (E-QCM).

  17. Click functionalization of phenyl-capped bithiophene on azide-terminated self-assembled monolayers

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Yijun; Cui, Jiaxi [Max Planck Institute for Polymer Research (MPIP), Ackermannweg 10, Mainz 55128 (Germany); Ikeda, Taichi, E-mail: IKEDA.Taichi@nims.go.jp [Max Planck Institute for Polymer Research (MPIP), Ackermannweg 10, Mainz 55128 (Germany); Polymer Materials Unit, National Institute for Materials Science (NIMS), 1-1 Namiki, Tsukuba 305-0044 (Japan)

    2015-11-15

    Graphical abstract: - Highlights: • Electrochemically-active self-assembled monolayers with phenyl-capped bithiophene were prepared. • Post-functionalization method based on click chemistry solved the solubility issue of phenyl-capped thiophene alkanethiol. • The capture and release of the counter anions during the redox reaction were detectable by E-QCM. - Abstract: We immobilized tetra(ethylene glycol)-substituted phenyl-capped bithiophene with alkyne terminals (Ph2TPh-alkyne) on azide-terminated self-assembled monolayers (N{sub 3}-SAMs) by Cu-catalyzed azide-alkyne cycloaddition reaction. Ph2TPh-functionalized SAMs on a gold substrate showed reversible electrochemical response. The surface densities of the azide groups in N{sub 3}-SAMs and Ph2TPh units in Ph2TPh-functionalized SAMs were estimated to be 7.3 ± 0.3 × 10{sup −10} mol cm{sup −2} and 4.6 ± 0.3 × 10{sup −10} mol cm{sup −2}, respectively, by quartz crystal microbalance (QCM). Most of Ph2TPh-alkynes are considered to be anchored on N{sub 3}-SAMs via both terminal groups. Ph2TPh-functionalized SAMs exhibited reversible redox peaks in cyclic voltammetry (CV). In redox reaction, reversible capture and release of the counter anion could be monitored by electrochemical QCM (E-QCM).

  18. Clicked Cinnamic/Caffeic Esters and Amides as Radical Scavengers and 5-Lipoxygenase Inhibitors

    Directory of Open Access Journals (Sweden)

    Jérémie A. Doiron

    2014-01-01

    Full Text Available 5-Lipoxygenase (5-LO is the key enzyme responsible for the conversion of arachidonic acid to leukotrienes, a class of lipid mediators implicated in inflammatory disorders. In this paper, we describe the design, synthesis, and preliminary activity studies of novel clicked caffeic esters and amides as radical scavengers and 5-LO inhibitors. From known 5-LO inhibitor 3 as a lead, cinnamic esters 8a–h and amides 9a–h as well as caffeic esters 15a–h and amides 16a–h were synthesized by Cu(I-catalyzed [1,3]-dipolar cycloaddition with the appropriate azide precursors and terminal alkynes. All caffeic analogs are proved to be good radical scavengers (IC50: 10–20 μM. Esters 15g and 15f possessed excellent 5-LO inhibition activity in HEK293 cells and were equipotent with the known 5-LO inhibitor CAPE and more potent than Zileuton. Several synthesized esters possess activities rivaling Zileuton in stimulated human polymorphonuclear leukocytes.

  19. Microscopic mechanism of electron transfer through the hydrogen bonds between carboxylated alkanethiol molecules connected to gold electrodes

    KAUST Repository

    Li, Yang; Tu, Xingchen; Wang, Minglang; Wang, Hao; Sanvito, Stefano; Hou, Shimin

    2014-01-01

    © 2014 AIP Publishing LLC. The atomic structure and the electron transfer properties of hydrogen bonds formed between two carboxylated alkanethiol molecules connected to gold electrodes are investigated by employing the non-equilibrium Green's function formalism combined with density functional theory. Three types of molecular junctions are constructed, in which one carboxyl alkanethiol molecule contains two methylene, -CH2, groups and the other one is composed of one, two, or three -CH2 groups. Our calculations show that, similarly to the cases of isolated carboxylic acid dimers, in these molecular junctions the two carboxyl, -COOH, groups form two H-bonds resulting in a cyclic structure. When self-interaction corrections are explicitly considered, the calculated transmission coefficients of these three H-bonded molecular junctions at the Fermi level are in good agreement with the experimental values. The analysis of the projected density of states confirms that the covalent Au-S bonds localized at the molecule-electrode interfaces and the electronic coupling between -COOH and S dominate the low-bias junction conductance. Following the increase of the number of the -CH2 groups, the coupling between -COOH and S decreases deeply. As a result, the junction conductance decays rapidly as the length of the H-bonded molecules increases. These findings not only provide an explanation to the observed distance dependence of the electron transfer properties of H-bonds, but also help the design of molecular devices constructed through H-bonds.

  20. Microscopic mechanism of electron transfer through the hydrogen bonds between carboxylated alkanethiol molecules connected to gold electrodes

    KAUST Repository

    Li, Yang

    2014-11-07

    © 2014 AIP Publishing LLC. The atomic structure and the electron transfer properties of hydrogen bonds formed between two carboxylated alkanethiol molecules connected to gold electrodes are investigated by employing the non-equilibrium Green\\'s function formalism combined with density functional theory. Three types of molecular junctions are constructed, in which one carboxyl alkanethiol molecule contains two methylene, -CH2, groups and the other one is composed of one, two, or three -CH2 groups. Our calculations show that, similarly to the cases of isolated carboxylic acid dimers, in these molecular junctions the two carboxyl, -COOH, groups form two H-bonds resulting in a cyclic structure. When self-interaction corrections are explicitly considered, the calculated transmission coefficients of these three H-bonded molecular junctions at the Fermi level are in good agreement with the experimental values. The analysis of the projected density of states confirms that the covalent Au-S bonds localized at the molecule-electrode interfaces and the electronic coupling between -COOH and S dominate the low-bias junction conductance. Following the increase of the number of the -CH2 groups, the coupling between -COOH and S decreases deeply. As a result, the junction conductance decays rapidly as the length of the H-bonded molecules increases. These findings not only provide an explanation to the observed distance dependence of the electron transfer properties of H-bonds, but also help the design of molecular devices constructed through H-bonds.

  1. C-Terminally modified peptides via cleavage of the HMBA linker by O-, N- or S-nucleophiles

    DEFF Research Database (Denmark)

    Hansen, Jonas; Diness, Frederik; Meldal, Morten Peter

    2016-01-01

    A large variety of C-terminally modified peptides was obtained by nucleophilic cleavage of the ester bond in solid phase linked peptide esters of 4-hydroxymethyl benzamide (HMBA). The developed methods provided peptides, C-terminally functionalized as esters, amides and thioesters, with high purity...... directly from the resin in a single reaction step. A comprehensive screening of the reaction conditions and scope for nucleophilic cleavage of peptides from the HMBA linker was performed....

  2. Use of piezoelectric-excited millimeter-sized cantilever sensors to measure albumin interaction with self-assembled monolayers of alkanethiols having different functional headgroups.

    Science.gov (United States)

    Campbell, Gossett A; Mutharasan, Raj

    2006-04-01

    In this paper, we describe a new modality of measuring human serum albumin (HSA) adsorption continuously on CH3-, COOH-, and OH-terminated self-assembled monolayers (SAMs) of C11-alkanethiols and the direct quantification of the adsorbed amount. A gold-coated piezoelectric-excited millimeter-sized cantilever (PEMC) sensor of 6-mm2 sensing area was fabricated, where resonant frequency decreases upon mass increase. The resonant frequency in air of the detection peak was 45.5 +/- 0.01 kHz. SAMs of C11-thiols (in absolute ethanol) with different end groups was prepared on the PEMC sensor and then exposed to buffer solution containing HSA at 10 microg/mL. The resonant frequency decreased exponentially and reached a steady-state value within 30 min. The decrease in resonant frequency indicates that the mass of the sensor increased due to HSA adsorption onto the SAM layer. The frequency change obtained for the HSA adsorption on CH3-, COOH-, and OH-terminated SAM were 520.8 +/- 8.6 (n = 3), 290.4 +/- 6.1 (n = 2), and 210.6 +/- 8.1 Hz (n = 3), respectively. These results confirm prior conclusions that albumin adsorption decreased in the order, CH(3) > COOH > OH. Observed binding rate constants were 0.163 +/- 0.003, 0.248 +/- 0.006, and 0.381 +/- 0.001 min(-1), for methyl, carboxylic, and hydroxyl end groups, respectively. The significance of the results reported here is that both the formation of self-assembled monolayers and adsorption of serum protein onto the formed layer can be measured continuously, and quantification of the adsorbed amount can be determined directly.

  3. First-principles density functional theory (DFT) study of gold nanorod and its interaction with alkanethiol ligands.

    Science.gov (United States)

    Hu, Hang; Reven, Linda; Rey, Alejandro

    2013-10-17

    The structure and mechanical properties of gold nanorods and their interactions with alkenthiolate self-assembled monolayers have been determined using a novel first-principle density functional theory simulation approach. The multifaceted, 1-dimensional, octagonal nanorod has alternate Au100 and Au110 surfaces. The structural optimization of the gold nanorods was performed with a mixed basis: the outermost layer of gold atoms used double-ζ plus polarization (DZP), the layer below used double-ζ (DZ), and the inner layers used single-ζ (SZ). The final structure compares favorably with simulations using DZP for all atoms. Phonon dispersion calculations and ab initio molecular dynamics (AIMD) were used to establish the dynamic and thermal stability of the system. From the AIMD simulations it was found that the nanorod system will undergo significant surface reconstruction at 300 K. In addition, when subjected to mechanical stress in the axial direction, the nanorod responds as an orthotropic material, with uniform expansion along the radial direction. The Young's moduli are 207 kbar in the axial direction and 631 kbar in the radial direction. The binding of alkanethiolates, ranging from methanethiol to pentanethiol, caused formation of surface point defects on the Au110 surfaces. On the Au100 surfaces, the defects occurred in the inner layer, creating a small surface island. These defects make positive and negative concavities on the gold nanorod surface, which helps the ligand to achieve a more stable state. The simulation results narrowed significant knowledge gaps on the alkanethiolate adsorption process and on their mutual interactions on gold nanorods. The mechanical characterization offers a new dimension to understand the physical chemistry of these complex nanoparticles.

  4. Rationalization of the selectivity between 1,3- and 1,2-migration: a DFT study on gold(i)-catalyzed propargylic ester rearrangement.

    Science.gov (United States)

    Jiang, Jingxing; Liu, Yan; Hou, Cheng; Li, Yinwu; Luan, Zihong; Zhao, Cunyuan; Ke, Zhuofeng

    2016-04-14

    Gold catalyzed rearrangement of propargylic esters can undergo 1,3-acyloxy migration to form allenes, or undergo 1,2-acyloxy migration to access gold-carbenoids. The variation in migration leads to different reactivities and diverse cascade transformations. The effect of terminal substituents is very important for the rearrangement. However, it remains ambiguous how terminal substituents govern the selectivity of the rearrangement. This study presents a theoretical model based on the resonance structure of gold activated propargylic ester complexes to rationalize the rearrangement selectivity. Substrates with a major resonance contributor A prefer 5-exo-dig cyclization (1,2-migration), while those with a major resonance contributor B prefer 6-endo-dig cyclization (1,3-migration). This concise model would be helpful in understanding and tuning the selectivity of the metal catalyzed rearrangement of propargylic esters.

  5. Gamma radiolysis and vinyl esters

    International Nuclear Information System (INIS)

    De Bruyn, H.; Balic, R.; Gilbert, R.G.

    1998-01-01

    The principle behind γ relaxation of free-radical polymerizations is that the source of initiating radicals can be switched off 'instantaneously'. In the absence of initiating radicals the only kinetic events remaining are propagation, transfer and termination. For monomers whose propagation rate coefficients have been determined, relaxation behaviour can be interpreted to determine radical-loss rate coefficients and test models of loss mechanisms. This technique has been employed successfully on styrene and MMA emulsion polymerizations. In the present study, vinyl acetate and vinyl neo-decanoate (a ten-carbon-branched homologue of vinyl acetate) were studied, with the propagation rate coefficients for both monomers being established by pulsed-laser polymerization. Both were found to exhibit rapid γ relaxation rates in emulsion polymerization. This is a surprising result because mechanisms for rapid relaxation in emulsion polymerizations require that chain transfer to monomer (which is rapid for both monomers) is followed by exit from the particle into the aqueous phase with subsequent re-entry into a radical-containing particle leading to bimolecular termination. It is not unreasonable to suppose that this may be possible for vinyl acetate which is fairly water soluble (∼0.3 M). However, vinyl neo-decanoate is virtually insoluble (∼0.00004 M) and hence desorption is extremely unlikely. The most likely explanation for the observed rapid relaxations is that some of the radicals produced by γ radiolysis are slow to initiate vinyl esters and hence act as radical traps. As vinyl esters are known to be particularly unreactive monomers. it is feasible that this experimental artifact affects them to a much greater extent than some of the monomers studied successfully with this technique in the past

  6. Physisorption of functionalized gold nanoparticles on AlGaN/GaN high electron mobility transistors for sensing applications.

    Science.gov (United States)

    Makowski, M S; Kim, S; Gaillard, M; Janes, D; Manfra, M J; Bryan, I; Sitar, Z; Arellano, C; Xie, J; Collazo, R; Ivanisevic, A

    2013-02-18

    AlGaN/GaN high electron mobility transistors (HEMTs) were used to measure electrical characteristics of physisorbed gold nanoparticles (Au NPs) functionalized with alkanethiols with a terminal methyl, amine, or carboxyl functional group. Additional alkanethiol was physisorbed onto the NP treated devices to distinguish between the effects of the Au NPs and alkanethiols on HEMT operation. Scanning Kelvin probe microscopy and electrical measurements were used to characterize the treatment effects. The HEMTs were operated near threshold voltage due to the greatest sensitivity in this region. The Au NP/HEMT system electrically detected functional group differences on adsorbed NPs which is pertinent to biosensor applications.

  7. Random telegraph signals by alkanethiol-protected Au nanoparticles in chemically assembled single-electron transistors

    International Nuclear Information System (INIS)

    Kano, Shinya; Azuma, Yasuo; Tanaka, Daisuke; Sakamoto, Masanori; Teranishi, Toshiharu; Smith, Luke W.; Smith, Charles G.; Majima, Yutaka

    2013-01-01

    We have studied random telegraph signals (RTSs) in a chemically assembled single-electron transistor (SET) at temperatures as low as 300 mK. The RTSs in the chemically assembled SET were investigated by measuring the source–drain current, using a histogram of the RTS dwell time, and calculating the power spectrum density of the drain current–time characteristics. It was found that the dwell time of the RTS was dependent on the drain voltage of the SET, but was independent of the gate voltage. Considering the spatial structure of the chemically assembled SET, the origin of the RTS is attributed to the trapped charges on an alkanethiol-protected Au nanoparticle positioned near the SET. These results are important as they will help to realize stable chemically assembled SETs in practical applications

  8. Preparation of Substituted Enol Derivatives From Terminal Alkynes and Their Synthetic Utility

    Science.gov (United States)

    DeBergh, John R.; Spivey, Kathleen M.; Ready, Joseph M.

    2009-01-01

    Stereodefined enol derivatives of aldehydes are prepared from terminal alkynes. Specifically, terminal alkynes are known to undergo Cp2ZrCl2-catalyzed methylalumination. Here, we show that the resultant vinylalanes can be oxygenated with peroxyzinc species to generate trisubstituted enolates. Electrophilic trapping with carboxylic anydrides or silyl triflates yields trisubstituted enol esters or silanes, respectively. The tandem carbometalation/oxygenation tolerates free and protected alcohols, heterocycles, olefins and nitriles. Likewise, amination can be accomplished using azodicarboxylates. Stereodefined enol esters can undergo asymmetric dihydroxylation to yield optically-active α-hydroxy aldehydes. Reduction with NaBH4 provides the diols of 1,1-disubstituted olefins in excellent ee. An application of this methodology to the enantioselective synthesis of the insect pheromone frontalin is presented. Finally, α-hydroxy aldehydes are shown to undergo homologation to a terminal alkyne, reductive amination, oxidation and olefination. Preliminary results indicate that tandem carbometalation/amination can be accomplished with azodicarboxylates. In this way, ene-hydrazines are formed in excellent yield. PMID:18517202

  9. Mechanical properties and chemical stability of pivalolactone-based poly(ether ester)s

    NARCIS (Netherlands)

    Tijsma, E.J.; Tijsma, E.J.; van der Does, L.; Bantjes, A.; Bantjes, A.; Vulic, I.

    1994-01-01

    The processing, mechanical and chemical properties of poly(ether ester)s, prepared from pivalolactone (PVL), 1,4-butanediol (4G) and dimethyl terephthalate (DMT), were studied. The poly(ether ester)s could easily be processed by injection moulding, owing to their favourable rheological and thermal

  10. Induction of transcription from the long terminal repeat of Moloney murine sarcoma provirus by UV-irradiation, x-irradiation, and phorbol ester

    International Nuclear Information System (INIS)

    Lin, C.S.; Goldthwait, D.A.; Samols, D.

    1990-01-01

    The long terminal repeat (LTR) of Moloney murine sarcoma virus (Mo-MuSV) was used as a model system to study the stress response of mammalian cells to physical carcinogens. The chloramphenicol acetyltransferase (CAT) gene was inserted between two Mo-MuSV LTRs, and the LTR-CAT-LTR construct was used for virus production and was integrated into the genome of NIH 3T3 cells in the proviral form. This construct was used to assure that the integrated CAT gene was driven by the promoter of the LTR. Expression of the CAT gene was stimulated 4-fold by UV irradiation, and the peak of activity was observed at 18 hr. In contrast, stimulation of the CAT expression after x-irradiation was 2-fold and occurred at 6 hr. Phorbol myristate acetate also stimulated CAT activity 4-fold with a peak at 6 hr. Down-regulation of protein kinase C blocked totally the response to x-irradiation but only partially the response to UV. The protein kinase inhibitor H7 blocked the response to treatment by UV, x-ray, and phorbol ester

  11. Controlled release from aspirin based linear biodegradable poly(anhydride esters) for anti-inflammatory activity.

    Science.gov (United States)

    Dasgupta, Queeny; Movva, Sahitya; Chatterjee, Kaushik; Madras, Giridhar

    2017-08-07

    This work reports the synthesis of a novel, aspirin-loaded, linear poly (anhydride ester) and provides mechanistic insights into the release of aspirin from this polymer for anti-inflammatory activity. As compared to conventional drug delivery systems that rely on diffusion based release, incorporation of bioactives in the polymer backbone is challenging and high loading is difficult to achieve. In the present study, we exploit the pentafunctional sugar alcohol (xylitol) to provide sites for drug (aspirin) attachment at its non-terminal OH groups. The terminal OH groups are polymerized with a diacid anhydride. The hydrolysis of the anhydride and ester bonds under physiological conditions release aspirin from the matrix. The resulting poly(anhydride ester) has high drug loading (53%) and displays controlled release kinetics of aspirin. The polymer releases 8.5 % and 20%, of the loaded drug in one and four weeks, respectively and has a release rate constant of 0.0035h -0.61 . The release rate is suitable for its use as an anti-inflammatory agent without being cytotoxic. The polymer exhibits good cytocompatibility and anti-inflammatory properties and may find applications as injectable or as an implantable bioactive material. The physical insights into the release mechanism can provide development of other drug loaded polymers. Copyright © 2017 Elsevier B.V. All rights reserved.

  12. Stanol esters attenuate the aggravating effect of dietary cholesterol on atherosclerosis in homozygous Watanabe rabbits

    DEFF Research Database (Denmark)

    Schrøder, Malene; Husche, Constanze; Pilegaard, Kirsten

    2009-01-01

    Plant stanols are marketed as natural means to lower blood cholesterol in humans; hence the effect on combined familial hyperlipidemia is not known. The objective was to investigate the effect of stanol esters on blood lipids and aortic atherosclerosis in homozygous WHHL rabbits challenged...... with dietary cholesterol. A total of 36 rabbits, 6 weeks of age, with initial plasma cholesterol of 22.5 mmol/L were assigned to two treatment groups fed a standard rabbit chow with 1 g/kg cholesterol or this diet added 34 g/kg stanol ester, respectively, for 16 weeks. Plasma cholesterol was measured initially...... and at termination, also in lipoproteins. Aortic atherosclerosis was evaluated as cholesterol content and area covered by plaque. Plasma cholesterol was not significantly different between the groups at termination (35.7 mmol/L vs. 35.5 mmol/L). A significant increase in LDL was seen (13.1 mmol/L vs. 16.5 mmol...

  13. Effects of protein kinase C activators on phorbol ester-sensitive and -resistant EL4 thymoma cells.

    Science.gov (United States)

    Sansbury, H M; Wisehart-Johnson, A E; Qi, C; Fulwood, S; Meier, K E

    1997-09-01

    Phorbol ester-sensitive EL4 murine thymoma cells respond to phorbol 12-myristate 13-acetate with activation of ERK mitogen-activated protein kinases, synthesis of interleukin-2, and death, whereas phorbol ester-resistant variants of this cell line do not exhibit these responses. Additional aspects of the resistant phenotype were examined, using a newly-established resistant cell line. Phorbol ester induced morphological changes, ERK activation, calcium-dependent activation of the c-Jun N-terminal kinase (JNK), interleukin-2 synthesis, and growth inhibition in sensitive but not resistant cells. A series of protein kinase C activators caused membrane translocation of protein kinase C's (PKCs) alpha, eta, and theta in both cell lines. While PKC eta was expressed at higher levels in sensitive than in resistant cells, overexpression of PKC eta did not restore phorbol ester-induced ERK activation to resistant cells. In sensitive cells, PKC activators had similar effects on cell viability and ERK activation, but differed in their abilities to induce JNK activation and interleukin-2 synthesis. PD 098059, an inhibitor of the mitogen activated protein (MAP)/ERK kinase kinase MEK, partially inhibited ERK activation and completely blocked phorbol ester-induced cell death in sensitive cells. Thus MEK and/or ERK activation, but not JNK activation or interleukin-2 synthesis, appears to be required for phorbol ester-induced toxicity. Alterations in phorbol ester response pathways, rather than altered expression of PKC isoforms, appear to confer phorbol ester resistance to EL4 cells.

  14. Molecular-scale noncontact atomic force microscopy contrasts in topography and energy dissipation on c(4x2) superlattice structures of alkanethiol self-assembled monolayers

    OpenAIRE

    Fukuma, Takeshi; Ichii, Takashi; Kobayashi, Kei; Yamada, Hirofumi; Matsushige, Kazumi

    2004-01-01

    Alkanethiol self-assembledmonolayers formed on Au(111) surfaces were investigated by noncontact atomic force microscopy (NC-AFM). Dodecanethiol monolayers prepared at 78 °C were imaged by NC-AFM, which revealed that the film is composed predominantly of two different phases of c(4×2)superlattice structures. The obtained molecular-scale NC-AFM contrasts are discussed in comparison with previously reported scanning tunneling microscopy images. We found that the energy dissipation image exhibits...

  15. Fluorine-doped tin oxide surfaces modified by self-assembled alkanethiols for thin-film devices

    Energy Technology Data Exchange (ETDEWEB)

    Alves, A.C.T.; Gomes, D.J.C.; Silva, J.R.; Silva, G.B., E-mail: george@cpd.ufmt.br

    2013-08-15

    In this work, we have investigated self-assembled monolayers (SAMs) from alkanethiols on fluorine-doped tin oxide (FTO) surfaces, which were used as an anode for thin-film devices prepared from the conductive copolymer so-called sulfonated poly(thiophene-3-[2-(2-methoxyethoxy) ethoxy]-2,5-diyl) (S-P3MEET). The assembled monolayers were characterized by using wetting contact angle, atomic force microscopy, and electrical measurements. The results indicated that dodecanethiol molecules, CH{sub 3}(CH{sub 2}){sub 11}SH, were well assembled on the FTO surfaces. In addition, it was found similar values of wetting contact angle for dodecanethiol assembled on both FTO and Au surfaces. Concerning the thin-film device, current–voltage analysis revealed a hysteresis. This behavior was associated to a charge-trapping effect and also to structural changes of the SAMs. Finally, charge injection capability of tin oxide electrodes can be improved by using SAMs and then this approach can plays an important role in molecular-scale electronic devices.

  16. Liquid Crystalline Thermosets from Ester, Ester-imide, and Ester-amide Oligomers

    Science.gov (United States)

    Dingemans, Theodorus J. (Inventor); Weiser, Erik S. (Inventor); St. Clair, Terry L. (Inventor)

    2009-01-01

    Main chain thermotropic liquid crystal esters, ester-imides, and ester-amides were prepared from AA, BB, and AB type monomeric materials and end-capped with phenylacetylene, phenylmaleimide, or nadimide reactive end-groups. The end-capped liquid crystal oligomers are thermotropic and have, preferably, molecular weights in the range of approximately 1000-15,000 grams per mole. The end-capped liquid crystaloligomers have broad liquid crystalline melting ranges and exhibit high melt stability and very low melt viscosities at accessible temperatures. The end-capped liquid crystal oli-gomers are stable forup to an hour in the melt phase. They are highly processable by a variety of melt process shape forming and blending techniques. Once processed and shaped, the end-capped liquid crystal oigomers were heated to further polymerize and form liquid crystalline thermosets (LCT). The fully cured products are rubbers above their glass transition temperatures.

  17. Amine terminated SAMs: Investigating why oxygen is present in these films

    International Nuclear Information System (INIS)

    Baio, J.E.; Weidner, T.; Brison, J.; Graham, D.J.; Gamble, Lara J.; Castner, David G.

    2009-01-01

    Self-assembled monolayers (SAMs) on gold prepared from amine-terminated alkanethiols have long been employed as model positively charged surfaces. Yet in previous studies significant amounts of unexpected oxygen containing species are always detected in amine terminated SAMs. Thus, the goal of this investigation was to determine the source of these oxygen species and minimize their presence in the SAM. The surface composition, structure, and order of amine-terminated SAMs on Au were characterized by X-ray photoelectron spectroscopy (XPS), time-of-flight secondary ion mass spectroscopy (ToF-SIMS), sum frequency generation (SFG) and near edge X-ray absorption fine structure (NEXAFS) spectroscopy. XPS determined compositions of amine-terminated SAMs in the current study exhibited oxygen concentrations of 2.4 ± 0.4 atomic %, a substantially lower amount of oxygen than reported in previously published studies. High-resolution XPS results from the S 2p , C 1s and N 1s regions did not detect any oxidized species. Angle-resolved XPS indicated that the small amount of oxygen detected was located at or near the amine head group. Small amounts of oxidized nitrogen, carbon and sulfur secondary ions, as well as ions attributed to water, were detected in the ToF-SIMS data due to the higher sensitivity of ToF-SIMS. The lack of N-O, S-O, and C-O stretches in the SFG spectra are consistent with the XPS and ToF-SIMS results and together show that oxidation of the amine-terminated thiols alone can only account for, at most, a small fraction of the oxygen detected by XPS. Both the SFG and angle-dependent NEXAFS indicated the presence of gauche defects in the amine SAMs. However, the SFG spectral features near 2865 cm -1 , assigned to the stretch of the methylene group next to the terminal amine unit, demonstrate the SAM is reasonably ordered. The SFG results also show another broad feature near 3200 cm -1 related to hydrogen-bonded water. From this multi-technique investigation it is

  18. Catalytic Ester to Stannane Functional Group Interconversion via Decarbonylative Cross-Coupling of Methyl Esters

    KAUST Repository

    Yue, Huifeng

    2018-01-03

    An unprecedented conversion of methyl esters to stannanes was realized, providing access to a series of arylstannanes via nickel catalysis. Various common esters including ethyl, cyclohexyl, benzyl, and phenyl esters can undergo the newly developed decarbonylative stannylation reaction. The reaction shows broad substrate scope, can differentiate between different types of esters, and if applied in consecutive fashion, allows the transformation of methyl esters into aryl fluorides or biaryls via fluororination or arylation.

  19. Catalytic Ester to Stannane Functional Group Interconversion via Decarbonylative Cross-Coupling of Methyl Esters

    KAUST Repository

    Yue, Huifeng; Zhu, Chen; Rueping, Magnus

    2018-01-01

    An unprecedented conversion of methyl esters to stannanes was realized, providing access to a series of arylstannanes via nickel catalysis. Various common esters including ethyl, cyclohexyl, benzyl, and phenyl esters can undergo the newly developed decarbonylative stannylation reaction. The reaction shows broad substrate scope, can differentiate between different types of esters, and if applied in consecutive fashion, allows the transformation of methyl esters into aryl fluorides or biaryls via fluororination or arylation.

  20. Electrical resistivity of monolayers and bilayers of alkanethiols in tunnel junction with gate electrode

    International Nuclear Information System (INIS)

    York, Roger L.; Nacionales, David; Slowinski, Krzysztof

    2005-01-01

    The tunneling resistances of monolayers and bilayers of n-alkanethiols in macroscopic Hg-Hg junctions with an electrochemical gate are reported. The resistances near zero bias calculated per 1 hydrocarbon chain vary from (5 ± 4) x 10 12 Ω for n-nonanethiol to (4 ± 2) x 10 16 Ω for n-octadecanethiol. These values indicate that monolayers of hydrocarbons in Hg-Hg junctions are substantially more resistive as compared to measurements employing microscopic tunnel junctions. The tunneling resistances of monolayer junctions are approximately 1 order of magnitude larger than those of bilayer junctions containing the same number of atoms indicating inefficient electronic coupling across the non-bonded -CH 3 |Hg interface. The symmetric current-voltage curves observed for the asymmetric junctions of Hg-S-(CH 2 ) n -CH 3 |Hg type suggest that these junctions do not behave as molecular diodes. Additional experimental evidence for the nature of the -CH 3 |Hg interface in the Hg-S-(CH 2 ) n -CH 3 |Hg junction is also presented

  1. Strain Rate Dependent Ductile-to-Brittle Transition of Graphite Platelet Reinforced Vinyl Ester Nanocomposites

    Directory of Open Access Journals (Sweden)

    Brahmananda Pramanik

    2014-01-01

    Full Text Available In previous research, the fractal dimensions of fractured surfaces of vinyl ester based nanocomposites were estimated applying classical method on 3D digital microscopic images. The fracture energy and fracture toughness were obtained from fractal dimensions. A noteworthy observation, the strain rate dependent ductile-to-brittle transition of vinyl ester based nanocomposites, is reinvestigated in the current study. The candidate materials of xGnP (exfoliated graphite nanoplatelets reinforced and with additional CTBN (Carboxyl Terminated Butadiene Nitrile toughened vinyl ester based nanocomposites that are subjected to both quasi-static and high strain rate indirect tensile load using the traditional Brazilian test method. High-strain rate indirect tensile testing is performed with a modified Split-Hopkinson Pressure Bar (SHPB. Pristine vinyl ester shows ductile deformation under quasi-static loading and brittle failure when subjected to high-strain rate loading. This observation reconfirms the previous research findings on strain rate dependent ductile-to-brittle transition of this material system. Investigation of both quasi-static and dynamic indirect tensile test responses show the strain rate effect on the tensile strength and energy absorbing capacity of the candidate materials. Contribution of nanoreinforcement to the tensile properties is reported in this paper.

  2. Esters with water esters 2-c to 6-c

    CERN Document Server

    Getzen, F W; Hefter, G T; Maczynski, Andrzej

    1992-01-01

    This volume is the first of two devoted to esters and water. It includes solubility data for binary systems containing an ester and water up to the end of 1988. The critical evaluations were all prepared by one author and an introductory section has been included to elaborate the philosophy and methodology followed in the evaluations.

  3. Formation of carboxy- and amide-terminated alkyl monolayers on silicon(111) investigated by ATR-FTIR, XPS, and X-ray scattering: Construction of photoswitchable surfaces

    DEFF Research Database (Denmark)

    Rück-Braun, Karola; Petersen, Michael Åxman; Michalik, Fabian

    2013-01-01

    -FTIR and XPS studies of the fulgimide samples revealed closely covered amide-terminated SAMs. Reversible photoswitching of the headgroup was read out by applying XPS, ATR-FTIR, and difference absorption spectra in the mid-IR. In XPS, we observed a reversible breathing of the amide/imide C1s and N1s signals......We have prepared high-quality, densely packed, self-assembled monolayers (SAMs) of carboxy-terminated alkyl chains on Si(111). The samples were made by thermal grafting of methyl undec-10-enoate under an inert atmosphere and subsequent cleavage of the ester functionality to disclose the carboxylic...... zigzag-like substitution pattern for the ester- and carboxy-terminated monolayer. Hydrolysis of the remaining H-Si(111) bonds at the surface furnished HO-Si(111) groups according to XPS and attenuated total reflection Fourier-transform infrared spectroscopy (ATR-FTIR) studies. The amide-terminated alkyl...

  4. Avocado and olive oil methyl esters

    International Nuclear Information System (INIS)

    Knothe, Gerhard

    2013-01-01

    Biodiesel, the mono-alkyl esters of vegetable oils, animal fats or other triacylglycerol-containing materials and an alternative to conventional petroleum-based diesel fuel, has been derived from a variety of feedstocks. Numerous feedstocks have been investigated as potential biodiesel sources, including commodity oils, however, the methyl esters of avocado and olive oil would likely be suitable as biodiesel fuel. In order to expand the database and comprehensive evaluation of the properties of vegetable oil esters, in this work the fuel-related properties of avocado and olive oil methyl esters, which exhibit similar fatty acid profiles including high oleic acid content, are determined. The cetane numbers of avocado oil methyl esters and olive oil methyl esters are relatively high, determined as 59.2 and 62.5, respectively, due to their elevated content of methyl oleate. Other properties are well within the ranges specified in biodiesel standards. The cloud points of both esters are slightly above 0 °C due to their content of saturated esters, especially methyl palmitate. Overall, avocado and olive oil yield methyl esters with fuel properties comparable to methyl esters from other commodity vegetable oils. The 1 H and 13 C NMR spectra of avocado and olive oil methyl esters are reported. -- Highlights: • Methyl esters of avocado and olive oil meet biodiesel fuel standards. • Provides comparison for methyl esters of other vegetable oils with high oleic content. • Discusses and compares present results with prior literature

  5. How anacetrapib inhibits the activity of the cholesteryl ester transfer protein? Perspective through atomistic simulations.

    Directory of Open Access Journals (Sweden)

    Tarja Äijänen

    2014-11-01

    Full Text Available Cholesteryl ester transfer protein (CETP mediates the reciprocal transfer of neutral lipids (cholesteryl esters, triglycerides and phospholipids between different lipoprotein fractions in human blood plasma. A novel molecular agent known as anacetrapib has been shown to inhibit CETP activity and thereby raise high density lipoprotein (HDL-cholesterol and decrease low density lipoprotein (LDL-cholesterol, thus rendering CETP inhibition an attractive target to prevent and treat the development of various cardiovascular diseases. Our objective in this work is to use atomistic molecular dynamics simulations to shed light on the inhibitory mechanism of anacetrapib and unlock the interactions between the drug and CETP. The results show an evident affinity of anacetrapib towards the concave surface of CETP, and especially towards the region of the N-terminal tunnel opening. The primary binding site of anacetrapib turns out to reside in the tunnel inside CETP, near the residues surrounding the N-terminal opening. Free energy calculations show that when anacetrapib resides in this area, it hinders the ability of cholesteryl ester to diffuse out from CETP. The simulations further bring out the ability of anacetrapib to regulate the structure-function relationships of phospholipids and helix X, the latter representing the structural region of CETP important to the process of neutral lipid exchange with lipoproteins. Altogether, the simulations propose CETP inhibition to be realized when anacetrapib is transferred into the lipid binding pocket. The novel insight gained in this study has potential use in the development of new molecular agents capable of preventing the progression of cardiovascular diseases.

  6. An efficient Monte Carlo algorithm for the fast equilibration and atomistic simulation of alkanethiol self-assembled monolayers on a Au(111) substrate.

    Science.gov (United States)

    Alexiadis, Orestis; Daoulas, Kostas Ch; Mavrantzas, Vlasis G

    2008-01-31

    A new Monte Carlo algorithm is presented for the simulation of atomistically detailed alkanethiol self-assembled monolayers (R-SH) on a Au(111) surface. Built on a set of simpler but also more complex (sometimes nonphysical) moves, the new algorithm is capable of efficiently driving all alkanethiol molecules to the Au(111) surface, thereby leading to full surface coverage, irrespective of the initial setup of the system. This circumvents a significant limitation of previous methods in which the simulations typically started from optimally packed structures on the substrate close to thermal equilibrium. Further, by considering an extended ensemble of configurations each one of which corresponds to a different value of the sulfur-sulfur repulsive core potential, sigmass, and by allowing for configurations to swap between systems characterized by different sigmass values, the new algorithm can adequately simulate model R-SH/Au(111) systems for values of sigmass ranging from 4.25 A corresponding to the Hautman-Klein molecular model (J. Chem. Phys. 1989, 91, 4994; 1990, 93, 7483) to 4.97 A corresponding to the Siepmann-McDonald model (Langmuir 1993, 9, 2351), and practically any chain length. Detailed results are presented quantifying the efficiency and robustness of the new method. Representative simulation data for the dependence of the structural and conformational properties of the formed monolayer on the details of the employed molecular model are reported and discussed; an investigation of the variation of molecular organization and ordering on the Au(111) substrate for three CH3-(CH2)n-SH/Au(111) systems with n=9, 15, and 21 is also included.

  7. Surface barrier analysis of semi-insulating and n{sup +}-type GaAs(0 0 1) following passivation with n-alkanethiol SAMs

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, Gregory M. [Laboratory for Quantum Semiconductors and Photon-Based BioNanotechnology, Department of Electrical and Computer Engineering, Universite de Sherbrooke, Sherbrooke, Quebec, J1K 2R1 (Canada); Institute for Chemical Process and Environmental Technology, National Research Council of Canada, Ottawa, Ontario, K1A 0R6 (Canada); Bensebaa, Farid [Institute for Chemical Process and Environmental Technology, National Research Council of Canada, Ottawa, Ontario, K1A 0R6 (Canada); Dubowski, Jan J., E-mail: jan.j.dubowski@usherbrooke.ca [Laboratory for Quantum Semiconductors and Photon-Based BioNanotechnology, Department of Electrical and Computer Engineering, Universite de Sherbrooke, Sherbrooke, Quebec, J1K 2R1 (Canada)

    2011-02-15

    The surface Fermi level of semi-insulating and n{sup +}-type GaAs(0 0 1) was determined before and after passivation with n-alkanethiol self-assembled monolayers (SAMs) by X-ray photoelectron spectroscopy. Fermi level positioning was achieved using Au calibration pads integrated directly onto the GaAs surface, prior to SAM deposition, in order to provide a surface equipotential binding energy reference. Fermi level pinning within 50 meV and surface barrier characteristics according to the Advanced Unified Defect Model were observed. Our results demonstrate the effectiveness of the Au integration technique for the determination of band-edge referenced Fermi level positions and are relevant to an understanding of emerging technologies based on the molecular-semiconductor junction.

  8. How anacetrapib inhibits the activity of the cholesteryl ester transfer protein? Perspective through atomistic simulations

    DEFF Research Database (Denmark)

    Aijanen, T.; Koivuniemi, A.; Javanainen, M.

    2014-01-01

    Cholesteryl ester transfer protein (CETP) mediates the reciprocal transfer of neutral lipids (cholesteryl esters, triglycerides) and phospholipids between different lipoprotein fractions in human blood plasma. A novel molecular agent known as anacetrapib has been shown to inhibit CETP activity...... and thereby raise high density lipoprotein (HDL)-cholesterol and decrease low density lipoprotein (LDL)-cholesterol, thus rendering CETP inhibition an attractive target to prevent and treat the development of various cardiovascular diseases. Our objective in this work is to use atomistic molecular dynamics...... simulations to shed light on the inhibitory mechanism of anacetrapib and unlock the interactions between the drug and CETP. The results show an evident affinity of anacetrapib towards the concave surface of CETP, and especially towards the region of the N-terminal tunnel opening. The primary binding site...

  9. Palladium-catalysed arylation of acetoacetate esters to yield 2-arylacetic acid esters

    CSIR Research Space (South Africa)

    Zeevaart, JG

    2004-05-24

    Full Text Available , was developed simultaneously by Hart- wig and Buchwald.5 Typically the tert-butyl ester of propionic acid is treated with an aryl halide (bromide or chloride) in the presence of a strong base, palladium and a bulky phosphine ligand or a bulky imidazolinium CO2t... novel palladium- catalysed conditions for the arylation of acetoacetate esters resulting in the formation of 2-arylacetic acid esters. When we attempted the arylation of tert-butyl aceto- acetate 1a with bromobenzene 2a using mild reaction conditions (K3...

  10. Ester Tuiksoo. Proua Suhkru kibedad päevad / Ester Tuiksoo ; interv. Piret Tali

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2005-01-01

    Põllumajandusminister Ester Tuiksoo, kellel peagi täitub ministri ametis aasta Euroopa Liidu suhkrutrahvist, maaettevõtlusest, põllumajandusest, Euroopa Liidu toetustest, ministri elu- ja teenistuskäigust. Lisa: Ester Tuiksoo

  11. Synthetic Methods for Ester Bond Formation and Conformational Analysis of Ester-Containing Carbohydrates

    Science.gov (United States)

    Hackbusch, Sven

    This dissertation encompasses work related to synthetic methods for the formation of ester linkages in organic compounds, as well as the investigation of the conformational influence of the ester functional group on the flexibility of inter-saccharide linkages, specifically, and the solution phase structure of ester-containing carbohydrate derivatives, in general. Stereoselective reactions are an important part of the field of asymmetric synthesis and an understanding of their underlying mechanistic principles is essential for rational method development. Here, the exploration of a diastereoselective O-acylation reaction on a trans-2-substituted cyclohexanol scaffold is presented, along with possible reasons for the observed reversal of stereoselectivity dependent on the presence or absence of an achiral amine catalyst. In particular, this work establishes a structure-activity relationship with regard to the trans-2-substituent and its role as a chiral auxiliary in the reversal of diastereoselectivity. In the second part, the synthesis of various ester-linked carbohydrate derivatives, and their conformational analysis is presented. Using multidimensional NMR experiments and computational methods, the compounds' solution-phase structures were established and the effect of the ester functional group on the molecules' flexibility and three-dimensional (3D) structure was investigated and compared to ether or glycosidic linkages. To aid in this, a novel Karplus equation for the C(sp2)OCH angle in ester-linked carbohydrates was developed on the basis of a model ester-linked carbohydrate. This equation describes the sinusoidal relationship between the C(sp2)OCH dihedral angle and the corresponding 3JCH coupling constant that can be determined from a J-HMBC NMR experiment. The insights from this research will be useful in describing the 3D structure of naturally occurring and lab-made ester-linked derivatives of carbohydrates, as well as guiding the de novo-design of

  12. Environmental effect of rapeseed oil ethyl ester

    International Nuclear Information System (INIS)

    Makareviciene, V.; Janulis, P.

    2003-01-01

    Exhaust emission tests were conducted on rapeseed oil methyl ester (RME), rapeseed oil ethyl ester (REE) and fossil diesel fuel as well as on their mixtures. Results showed that when considering emissions of nitrogen oxides (NO x ), carbon monoxide (CO) and smoke density, rapeseed oil ethyl ester had less negative effect on the environment in comparison with that of rapeseed oil methyl ester. When fuelled with rapeseed oil ethyl ester, the emissions of NO x showed an increase of 8.3% over those of fossil diesel fuel. When operated on 25-50% bio-ester mixed with fossil diesel fuel, NO x emissions marginally decreased. When fuelled with pure rapeseed oil ethyl ester, HC emissions decreased by 53%, CO emissions by 7.2% and smoke density 72.6% when compared with emissions when fossil diesel fuel was used. Carbon dioxide (CO 2 ) emissions, which cause greenhouse effect, decreased by 782.87 g/kWh when rapeseed oil ethyl ester was used and by 782.26 g/kWh when rapeseed oil methyl ester was used instead of fossil diesel fuel. Rapeseed oil ethyl ester was more rapidly biodegradable in aqua environment when compared with rapeseed oil methyl ester and especially with fossil diesel fuel. During a standard 21 day period, 97.7% of rapeseed oil methyl ester, 98% of rapeseed oil ethyl ester and only 61.3% of fossil diesel fuel were biologically decomposed. (author)

  13. The European source term code ESTER - basic ideas and tools for coupling of ATHLET and ESTER

    International Nuclear Information System (INIS)

    Schmidt, F.; Schuch, A.; Hinkelmann, M.

    1993-04-01

    The French software house CISI and IKE of the University of Stuttgart have developed during 1990 and 1991 in the frame of the Shared Cost Action Reactor Safety the informatic structure of the European Source TERm Evaluation System (ESTER). Due to this work tools became available which allow to unify on an European basis both code development and code application in the area of severe core accident research. The behaviour of reactor cores is determined by thermal hydraulic conditions. Therefore for the development of ESTER it was important to investigate how to integrate thermal hydraulic code systems with ESTER applications. This report describes the basic ideas of ESTER and improvements of ESTER tools in view of a possible coupling of the thermal hydraulic code system ATHLET and ESTER. Due to the work performed during this project the ESTER tools became the most modern informatic tools presently available in the area of severe accident research. A sample application is given which demonstrates the use of the new tools. (orig.) [de

  14. Cobalt-catalyzed hydrogenation of esters to alcohols: unexpected reactivity trend indicates ester enolate intermediacy.

    Science.gov (United States)

    Srimani, Dipankar; Mukherjee, Arup; Goldberg, Alexander F G; Leitus, Gregory; Diskin-Posner, Yael; Shimon, Linda J W; Ben David, Yehoshoa; Milstein, David

    2015-10-12

    The atom-efficient and environmentally benign catalytic hydrogenation of carboxylic acid esters to alcohols has been accomplished in recent years mainly with precious-metal-based catalysts, with few exceptions. Presented here is the first cobalt-catalyzed hydrogenation of esters to the corresponding alcohols. Unexpectedly, the evidence indicates the unprecedented involvement of ester enolate intermediates. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. The rate of charge tunneling is insensitive to polar terminal groups in self-assembled monolayers in Ag(TS)S(CH2)(n)M(CH2)(m)T//Ga2O3/EGaIn junctions.

    Science.gov (United States)

    Yoon, Hyo Jae; Bowers, Carleen M; Baghbanzadeh, Mostafa; Whitesides, George M

    2014-01-08

    This paper describes a physical-organic study of the effect of uncharged, polar, functional groups on the rate of charge transport by tunneling across self-assembled monolayer (SAM)-based large-area junctions of the form Ag(TS)S(CH2)(n)M(CH2)(m)T//Ga2O3/EGaIn. Here Ag(TS) is a template-stripped silver substrate, -M- and -T are "middle" and "terminal" functional groups, and EGaIn is eutectic gallium-indium alloy. Twelve uncharged polar groups (-T = CN, CO2CH3, CF3, OCH3, N(CH3)2, CON(CH3)2, SCH3, SO2CH3, Br, P(O)(OEt)2, NHCOCH3, OSi(OCH3)3), having permanent dipole moments in the range 0.5 < μ < 4.5, were incorporated into the SAM. A comparison of the electrical characteristics of these junctions with those of junctions formed from n-alkanethiolates led to the conclusion that the rates of charge tunneling are insensitive to the replacement of terminal alkyl groups with the terminal polar groups in this set. The current densities measured in this work suggest that the tunneling decay parameter and injection current for SAMs terminated in nonpolar n-alkyl groups, and polar groups selected from common polar organic groups, are statistically indistinguishable.

  16. Regioselective 1,4- and 1,6-Conjugate Additions of Grignard Reagent-Derived Organozinc(II)ates to Polyconjugated Esters.

    Science.gov (United States)

    Hatano, Manabu; Mizuno, Mai; Ishihara, Kazuaki

    2016-09-16

    Regioselective synthetic methods were developed for 1,4- and 1,6-conjugate additions of Grignard reagent-derived organozinc(II)ates to malonate-derived polyconjugated esters. By taking advantage of the tight ion-pair control of organozinc(II)ates, it was possible to switch between 1,4- and 1,6-conjugate additions by introducing a terminal ethoxy moiety in the conjugation.

  17. Poly(ester-anhydride):poly(beta-amino ester) micro- and nanospheres: DNA encapsulation and cellular transfection.

    Science.gov (United States)

    Pfeifer, Blaine A; Burdick, Jason A; Little, Steve R; Langer, Robert

    2005-11-04

    Poly(ester-anhydride) delivery devices allow flexibility regarding carrier dimensions (micro- versus nanospheres), degradation rate (anhydride versus ester hydrolysis), and surface labeling (through the anhydride functional unit), and were therefore tested for DNA encapsulation and transfection of a macrophage P388D1 cell line. Poly(l-lactic acid-co-sebacic anhydride) and poly(l-lactic acid-co-adipic anhydride) were synthesized through melt condensation, mixed with 25 wt.% poly(beta-amino ester), and formulated with plasmid DNA (encoding firefly luciferase) into micro- and nanospheres using a double emulsion/solvent evaporation technique. The micro- and nanospheres were then characterized (size, morphology, zeta potential, DNA release) and assayed for DNA encapsulation and cellular transfection over a range of poly(ester-anhydride) copolymer ratios. Poly(ester-anhydride):poly(beta-amino ester) composite microspheres (6-12 microm) and nanospheres (449-1031 nm), generated with copolymers containing between 0 and 25% total polyanhydride content, encapsulated plasmid DNA (>or=20% encapsulation efficiency). Within this polyanhydride range, poly(adipic anhydride) copolymers provided DNA encapsulation at an increased anhydride content (10%, microspheres; 10-25%, nanospheres) compared to poly(sebacic anhydride) copolymers (1%, microspheres and nanospheres) with cellular transfection correlating with the observed DNA encapsulation.

  18. Application conditions for ester cured alkaline phenolic resin sand

    Directory of Open Access Journals (Sweden)

    Ren-he Huang

    2016-07-01

    Full Text Available Five organic esters with different curing speeds: propylene carbonate (i.e. high-speed ester A; 1, 4-butyrolactone; glycerol triacetate (i.e. medium-speed ester B; glycerol diacetate; dibasic ester (DBE (i.e. low-speed ester C, were chosen to react with alkaline phenolic resin to analyze the application conditions of ester cured alkaline phenolic resin. The relationships between the curing performances of the resin (including pH value, gel pH value, gel time of resin solution, heat release rate of the curing reaction and tensile strength of the resin sand and the amount of added organic ester and curing temperature were investigated. The results indicated the following: (1 The optimal added amount of organic ester should be 25wt.%-30wt.% of alkaline phenolic resin and it must be above 20wt.%-50 wt.% of the organic ester hydrolysis amount. (2 High-speed ester A (propylene carbonate has a higher curing speed than 1, 4-butyrolactone, and they were both used as high-speed esters. Glycerol diacetate is not a high-speed ester in alkaline phenolic resin although it was used as a high-speed ester in ester cured sodium silicate sand; glycerol diacetate and glycerol triacetate can be used as medium-speed esters in alkaline phenolic resin. (3 High-speed ester A, medium-speed ester B (glycerol triacetate and low-speed ester C (dibasic ester, i.e., DBE should be used below 15 ìC, 35 ìC and 50 ìC, respectively. High-speed ester A or low-speed ester C should not be used alone but mixed with medium-speed ester B to improve the strength of the resin sand. (4 There should be a suitable solid content (generally 45wt.%-65wt.% of resin, alkali content (generally 10wt.%-15wt.% of resin and viscosity of alkaline phenolic resin (generally 50-300 mPa≤s in the preparation of alkaline phenolic resin. Finally, the technique conditions of alkaline phenolic resin preparation and the application principles of organic ester were discussed.

  19. Chain propagation and termination mechanisms for polymerization of conjugated polar alkenes by [Al]-based frustrated Lewis pairs

    KAUST Repository

    He, Jianghua

    2014-11-25

    A combined experimental and theoretical study on mechanistic aspects of polymerization of conjugated polar alkenes by frustrated Lewis pairs (FLPs) based on N-heterocyclic carbene (NHC) and Al(C6F5)3 pairs is reported. This study consists of three key parts: structural characterization of active propagating intermediates, propagation kinetics, and chain-termination pathways. Zwitterionic intermediates that simulate the active propagating species in such polymerization have been generated or isolated from the FLP activation of monomers such as 2-vinylpyridine and 2-isopropenyl-2-oxazoline-one of which, IMes+-CH2C(Me)=(C3H2NO)Al(C6F5)3 - (2), has been structurally characterized. Kinetics performed on the polymerization of 2-vinylpyridine by ItBu/Al(C6F5)3 revealed that the polymerization follows a zero-order dependence on monomer concentration and a first-order dependence on initiator (ItBu) and activator [Al(C6F5)3] concentrations, indicating a bimolecular, activated monomer propagation mechanism. The Lewis pair polymerization of conjugate polar alkenes such as methacrylates is accompanied by competing chain-termination side reactions; between the two possible chain-termination pathways, the one that proceeds via intramolecular backbiting cyclization involving nucleophilic attack of the activated ester group of the growing polymer chain by the O-ester enolate active chain end to generate a six-membered lactone (δ-valerolactone)-terminated polymer chain is kinetically favored, but thermodynamically disfavored, over the pathway leading to the -ketoester-terminated chain, as revealed by computational studies.

  20. Rearrangement of beta,gamma-unsaturated esters with thallium trinitrate: synthesis of indans bearing a beta-keto ester moiety

    Directory of Open Access Journals (Sweden)

    Silva Jr. Luiz F.

    2006-01-01

    Full Text Available The rearrangement of beta,gamma-unsaturated esters, such as 2-(3,4-dihydronaphthalen-1-yl-propionic acid ethyl ester, with thallium trinitrate (TTN in acetic acid leads to 3-indan-1-yl-2-methyl-3-oxo-propionic acid ethyl ester in good yield, through a ring contraction reaction. The new indans thus obtained feature a beta-keto ester moiety, which would be useful for further functionalization.

  1. Neutral Lipid Biosynthesis in Engineered Escherichia coli: Jojoba Oil-Like Wax Esters and Fatty Acid Butyl Esters

    OpenAIRE

    Kalscheuer, Rainer; Stöveken, Tim; Luftmann, Heinrich; Malkus, Ursula; Reichelt, Rudolf; Steinbüchel, Alexander

    2006-01-01

    Wax esters are esters of long-chain fatty acids and long-chain fatty alcohols which are of considerable commercial importance and are produced on a scale of 3 million tons per year. The oil from the jojoba plant (Simmondsia chinensis) is the main biological source of wax esters. Although it has a multitude of potential applications, the use of jojoba oil is restricted, due to its high price. In this study, we describe the establishment of heterologous wax ester biosynthesis in a recombinant E...

  2. Regioselective Synthesis of Cellulose Ester Homopolymers

    Science.gov (United States)

    Daiqiang Xu; Kristen Voiges; Thomas Elder; Petra Mischnick; Kevin J. Edgar

    2012-01-01

    Regioselective synthesis of cellulose esters is extremely difficult due to the small reactivity differences between cellulose hydroxyl groups, small differences in steric demand between acyl moieties of interest, and the difficulty of attaching and detaching many protecting groups in the presence of cellulose ester moieties without removing the ester groups. Yet the...

  3. Dual N- and C-terminal helices are required for endoplasmic reticulum and lipid droplet association of alcohol acetyltransferases in Saccharomyces cerevisiae.

    Directory of Open Access Journals (Sweden)

    Jyun-Liang Lin

    Full Text Available In the yeast Saccharomyces cerevisiae two alcohol acetyltransferases (AATases, Atf1 and Atf2, condense short chain alcohols with acetyl-CoA to produce volatile acetate esters. Such esters are, in large part, responsible for the distinctive flavors and aromas of fermented beverages including beer, wine, and sake. Atf1 and Atf2 localize to the endoplasmic reticulum (ER and Atf1 is known to localize to lipid droplets (LDs. The mechanism and function of these localizations are unknown. Here, we investigate potential mechanisms of Atf1 and Atf2 membrane association. Segments of the N- and C-terminal domains of Atf1 (residues 24-41 and 508-525, respectively are predicted to be amphipathic helices. Truncations of these helices revealed that the terminal domains are essential for ER and LD association. Moreover, mutations of the basic or hydrophobic residues in the N-terminal helix and hydrophobic residues in the C-terminal helix disrupted ER association and subsequent sorting from the ER to LDs. Similar amphipathic helices are found at both ends of Atf2, enabling ER and LD association. As was the case with Atf1, mutations to the N- and C-terminal helices of Atf2 prevented membrane association. Sequence comparison of the AATases from Saccharomyces, non-Saccharomyces yeast (K. lactis and P. anomala and fruits species (C. melo and S. lycopersicum showed that only AATases from Saccharomyces evolved terminal amphipathic helices. Heterologous expression of these orthologs in S. cerevisiae revealed that the absence of terminal amphipathic helices eliminates LD association. Combined, the results of this study suggest a common mechanism of membrane association for AATases via dual N- and C-terminal amphipathic helices.

  4. Correlation and prediction of mixing thermodynamic properties of ester-containing systems: Ester + alkane and ester + ester binary systems and the ternary dodecane + ethyl pentanoate + ethyl ethanoate

    International Nuclear Information System (INIS)

    Pérez, Noelia; Fernández, Luís; Ortega, Juan; Toledo, Francisco J.; Wisniak, Jaime

    2012-01-01

    Highlights: ► Excess enthalpies and volumes were measured for ester–ester–alkane. ► Mixing behaviour for ester–ester, ester–alkane and ester–ester–alkane are analyzed. ► Correlations with a new polynomial model reproduce well the mixing properties. ► UNIFAC predictions for h E result acceptable excluding the ester–ester mixtures. - Abstract: Excess thermodynamic properties V m E and H m E , have been measured for the ternary mixture dodecane + ethyl pentanoate + ethyl ethanoate and for the corresponding binaries dodecane + ethyl pentanoate, dodecane + ethyl ethanoate, ethyl pentanoate + ethyl ethanoate at 298.15 K. All mixtures show endothermic and expansive effects. Experimental results are correlated with a suitable equation whose final form for the excess ternary quantity M E contains the particular contributions of the three binaries (i–j) and a last term corresponding to the ternary, all of them obtained considering fourth-order interactions. The fit goodness for all mixtures is good and comparable to others equations taken from the literature. In this work the dissolution model for the binaries and ternary is analyzed with a special attention to ester–ester binaries whose behaviour is discussed. The application of the UNIFAC group contribution model to estimate the H m E yields acceptable results for the binaries (with the exception of ester–ester) and for the ternary mixture.

  5. Synthesis of 11C labelled methyl esters: transesterification of enol esters versus BF3 catalysed esterification-a comparative study

    International Nuclear Information System (INIS)

    Ackermann, Uwe; Blanc, Paul; Falzon, Cheryl L.; Issa, William; White, Jonathan; Tochon-Danguy, Henri J.; Sachinidis, John I.; Scott, Andrew M.

    2006-01-01

    C-11 labelled methyl esters have been synthesized via the transesterification of enol esters in the presence of C-11 methanol and 1,3 dichlorodibutylstannoxane as catalyst. This method leaves functional groups intact and allows access to a wider variety of C-11 labelled methyl esters compared to the BF 3 catalysed ester formation, which uses carboxylic acids and C-11 methanol as starting materials

  6. Neutral lipid biosynthesis in engineered Escherichia coli: jojoba oil-like wax esters and fatty acid butyl esters.

    Science.gov (United States)

    Kalscheuer, Rainer; Stöveken, Tim; Luftmann, Heinrich; Malkus, Ursula; Reichelt, Rudolf; Steinbüchel, Alexander

    2006-02-01

    Wax esters are esters of long-chain fatty acids and long-chain fatty alcohols which are of considerable commercial importance and are produced on a scale of 3 million tons per year. The oil from the jojoba plant (Simmondsia chinensis) is the main biological source of wax esters. Although it has a multitude of potential applications, the use of jojoba oil is restricted, due to its high price. In this study, we describe the establishment of heterologous wax ester biosynthesis in a recombinant Escherichia coli strain by coexpression of a fatty alcohol-producing bifunctional acyl-coenzyme A reductase from the jojoba plant and a bacterial wax ester synthase from Acinetobacter baylyi strain ADP1, catalyzing the esterification of fatty alcohols and coenzyme A thioesters of fatty acids. In the presence of oleate, jojoba oil-like wax esters such as palmityl oleate, palmityl palmitoleate, and oleyl oleate were produced, amounting to up to ca. 1% of the cellular dry weight. In addition to wax esters, fatty acid butyl esters were unexpectedly observed in the presence of oleate. The latter could be attributed to solvent residues of 1-butanol present in the medium component, Bacto tryptone. Neutral lipids produced in recombinant E. coli were accumulated as intracytoplasmic inclusions, demonstrating that the formation and structural integrity of bacterial lipid bodies do not require specific structural proteins. This is the first report on substantial biosynthesis and accumulation of neutral lipids in E. coli, which might open new perspectives for the biotechnological production of cheap jojoba oil equivalents from inexpensive resources employing recombinant microorganisms.

  7. Ester Tuiksoo / Ester Tuiksoo ; interv. Piret Tali

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2007-01-01

    Juhan Partsi valitsuse (05.04.2004-13.04.2005) ja Andrus Ansipi valitsuse (13.04.2005-) põllumajandusminister Ester Tuiksoo oma lapsepõlvest ja elukutsevalikust, poliitilise karjääri algusest ja erakonna valikust, ministritöö kogemustest, naistest poliitikas

  8. Anticholinesterase activity of fluorochloronitroacetic acid esters

    Energy Technology Data Exchange (ETDEWEB)

    Ivanov, Yu.Ya.; Brel, V.K. Martynov, I.V.

    1984-11-01

    Results are presented from pharmacologic and biochemical experiments leading to the conclusion that fluorochloronitroacetic acid esters have anticholinesterase activity. Since the esters caused muscular weakness in mice, experiments were performed on isolated tissue preparation. The biochemical experiments consisted of finding the biomolecular constants of irreversible inhibition of acetylcholinesterase by the esters, using acetylcholinesterase from human erythrocytes, as well as horse serum cholinesterase. The ethyl and n-propyl esters of halogen nitroacetic acid were used in all experiments. It was found that the propyl ester caused an increase in the force of individual contractions in the isolated muscle specimens, plus an inability of the muscle to retain tetanus. The substances were determined to have an anticholinesterase effect. The mechanism of cholinesterase inhibition is not yet known. It is probable that the substances acylate the serine hydroxyl of the esterase center of the cholinestersase. 7 references, 1 figure.

  9. Probing the role of backbone hydrogen bonds in protein-peptide interactions by amide-to-ester mutations

    DEFF Research Database (Denmark)

    Eildal, Jonas N N; Hultqvist, Greta; Balle, Thomas

    2013-01-01

    -protein interactions, those of the PDZ domain family involve formation of intermolecular hydrogen bonds: C-termini or internal linear motifs of proteins bind as β-strands to form an extended antiparallel β-sheet with the PDZ domain. Whereas extensive work has focused on the importance of the amino acid side chains...... of the protein ligand, the role of the backbone hydrogen bonds in the binding reaction is not known. Using amide-to-ester substitutions to perturb the backbone hydrogen-bonding pattern, we have systematically probed putative backbone hydrogen bonds between four different PDZ domains and peptides corresponding...... to natural protein ligands. Amide-to-ester mutations of the three C-terminal amides of the peptide ligand severely affected the affinity with the PDZ domain, demonstrating that hydrogen bonds contribute significantly to ligand binding (apparent changes in binding energy, ΔΔG = 1.3 to >3.8 kcal mol(-1...

  10. QSAR for cholinesterase inhibition by organophosphorus esters and CNDO/2 calculations for organophosphorus ester hydrolysis

    Science.gov (United States)

    Johnson, H.; Kenley, R. A.; Rynard, C.; Golub, M. A.

    1985-01-01

    Quantitative structure-activity relationships were derived for acetyl- and butyrylcholinesterase inhibition by various organophosphorus esters. Bimolecular inhibition rate constants correlate well with hydrophobic substituent constants, and with the presence or absence of catonic groups on the inhibitor, but not with steric substituent constants. CNDO/2 calculations were performed on a separate set of organophosphorus esters, RR'P(O)X, where R and R' are alkyl and/or alkoxy groups and X is fluorine, chlorine or a phenoxy group. For each subset with the same X, the CNDO-derived net atomic charge at the central phosphorus atom in the ester correlates well with the alkaline hydrolysis rate constant. For the whole set of esters with different X, two equations were derived that relate either charge and leaving group steric bulk, or orbital energy and bond order to the hydrogen hydrolysis rate constant.

  11. Method of making a cyanate ester foam

    Science.gov (United States)

    Celina, Mathias C.; Giron, Nicholas Henry

    2014-08-05

    A cyanate ester resin mixture with at least one cyanate ester resin, an isocyanate foaming resin, other co-curatives such as polyol or epoxy compounds, a surfactant, and a catalyst/water can react to form a foaming resin that can be cured at a temperature greater than 50.degree. C. to form a cyanate ester foam. The cyanate ester foam can be heated to a temperature greater than 400.degree. C. in a non-oxidative atmosphere to provide a carbonaceous char foam.

  12. Naturally-occurring estradiol-17β-fatty acid esters, but not estradiol-17β, preferentially induce mammary tumorigenesis in female rats: Implications for an important role in human breast cancer

    International Nuclear Information System (INIS)

    Mills, Laura H.; Yu Jina; Xu Xiaomeng; Lee, Anthony J.; Zhu Baoting

    2008-01-01

    Because mammary glands are surrounded by adipose tissues, we hypothesize that the ultra-lipophilic endogenous estrogen-17β-fatty acid esters may have preferential hormonal and carcinogenic effects in mammary tissues compared to other target organs (such as the uterus and pituitary). This hypothesis is tested in the present study. We found that all 46 rats implanted with an estradiol-17β pellet developed large pituitary tumors (average weight = 251 ±103 mg) and had to be terminated early, but only 48% of them developed mammary tumors. In addition, approximately one-fourth of them developed a huge uterus. In the 26 animals implanted with a mixture containing estradiol-17β-stearate and estradiol-17β-palmitate (two representative estradiol-17β-fatty acid esters) or in the 29 animals implanted with estradiol-17β-stearate alone (in the same molar dose as estradiol-17β), 73% and 79%, respectively, of them developed mammary tumors, whereas only 3 or 2 animals, respectively, had to be terminated early due to the presence of a large pituitary tumor. Both tumorous and normal mammary tissues contained much higher levels of estrogen esterase than other tissues, which catalyzes the releases of bioactive estrogens from their fatty acid esters. In conclusion, while estradiol-17β is much stronger in inducing pituitary tumor (100% incidence) than mammary tumor, estradiol-17β-fatty acid esters have a higher efficacy than estradiol-17β in inducing mammary tumor and yet it only has little ability to induce uterine out-growth and pituitary tumorigenesis. This study establishes the endogenous estrogen-17β-fatty acid esters as preferential inducers of mammary tumorigenesis

  13. Allied, MGC link on cyanate esters

    International Nuclear Information System (INIS)

    Wood, A.

    1993-01-01

    In the latest of a line of joint ventures in its plastics business, Allied Signal has reached agreement with Mitsubishi Gas Chemical (MGC) to jointly develop thermoset cyanate ester resins and blends. The deal will involve further development of Allied Signal's Primaset phenol-formaldehyde cyanate ester resins, a new entrant in the thermoset arena. Although the Primaset resins were discovered in the 1960s, this would be the first time they are available commercially. The deal will marry Primaset technology with MGC's Skylex bisphenol A cyanate ester resins, says Fred DiAntonis, director/advanced materials at Allied Signal. The two firms are looking at marketing blends of the two materials. The potential market for these resins, used commercially by the electronics industry in printed circuit boards and by the aerospace industry in composites, is significant, says Robert P. Viarengo, Allied Signal president/performance materials. By aligning ourselves with MGC, the world leader in cyanate ester resin, we anticipate moving forward aggressively. The main competitor is Ciba, which acquired bisphenol A cyanate ester resins with its purchase of Rhone-Poulenc's high temperature resins business. DiAntonis estimates the market for cyanate ester resins could be worth $150 million by the end of the decade, although development costs have been in the tens of millions of dollars range

  14. Synthesis of a new energetic nitrate ester

    Energy Technology Data Exchange (ETDEWEB)

    Chavez, David E [Los Alamos National Laboratory

    2008-01-01

    Nitrate esters have been known as useful energetic materials since the discovery of nitroglycerin by Ascanio Sobrero in 1846. The development of methods to increase the safety and utility of nitroglycerin by Alfred Nobel led to the revolutionary improvement in the utility of nitroglycerin in explosive applications in the form of dynamite. Since then, many nitrate esters have been prepared and incorporated into military applications such as double-based propellants, detonators and as energetic plasticizers. Nitrate esters have also been shown to have vasodilatory effects in humans and thus have been studied and used for treatments of ailments such as angina. The mechanism of the biological response towards nitrate esters has been elucidated recently. Interestingly, many of the nitrate esters used for military purposes are liquids (ethylene glycol dinitrate, propylene glycol dinitrate, etc). Pentaerythritol tetranitrate (PETN) is one of the only solid nitrate esters, besides nitrocellulose, that is used in any application. Unfortunately, PETN melting point is above 100 {sup o}C, and thus must be pressed as a solid for detonator applications. A more practical material would be a melt-castable explosive, for potential simplification of manufacturing processes. Herein we describe the synthesis of a new energetic nitrate ester (1) that is a solid at ambient temperatures, has a melting point of 85-86 {sup o}C and has the highest density of any known nitrate ester composed only of carbon, hydrogen, nitrogen and oxygen. We also describe the chemical, thermal and sensitivity properties of 1 as well as some preliminary explosive performance data.

  15. Fundamental Characterization of the Micellar Self-Assembly of Sophorolipid Esters.

    Science.gov (United States)

    Koh, Amanda; Todd, Katherine; Sherbourne, Ezekiel; Gross, Richard A

    2017-06-13

    Surfactants are ubiquitous constituents of commercial and biological systems that function based on complex structure-dependent interactions. Sophorolipid (SL) n-alkyl esters (SL-esters) comprise a group of modified naturally derived glycolipids from Candida bombicola. Herein, micellar self-assembly behavior as a function of SL-ester chain length was studied. Surface tensions as low as 31.2 mN/m and critical micelle concentrations (CMCs) as low as 1.1 μM were attained for diacetylated SL-decyl ester (dASL-DE) and SL-octyl ester, respectively. For deacetylated SL-esters, CMC values reach a lower limit at SL-ester chains above n-butyl (SL-BE, 1-3 μM). This behavior of SL-esters with increasing hydrophobic tail length is unlike other known surfactants. Diffusion-ordered spectroscopy (DOSY) and T 1 relaxation NMR experiments indicate this behavior is due to a change in intramolecular interactions, which impedes the self-assembly of SL-esters with chain lengths above SL-BE. This hypothesis is supported by micellar thermodynamics where a disruption in trends occurs at n-alkyl ester chain lengths above those of SL-BE and SL-hexyl ester (SL-HE). Diacetylated (dA) SL-esters exhibit an even more unusual trend in that CMC increases from 1.75 to 815 μM for SL-ester chain lengths of dASL-BE and dASL-DE, respectively. Foaming studies, performed to reveal the macroscopic implications of SL-ester micellar behavior, show that the observed instability in foams formed using SL-esters are due to coalescence, which highlights the importance of understanding intermicellar interactions. This work reveals that SL-esters are an important new family of green high-performing surfactants with unique structure-property relationships that can be tuned to optimize micellar characteristics.

  16. Technetium and rhenium tracers with metabolizable ester functions

    International Nuclear Information System (INIS)

    Syhre, R.; Seifert, S.; Schneider, F.; Pietzsch, H.J.; Spies, H.; Johannsen, B.

    1993-01-01

    Re-DMSA (dimercaptosuccinic acid) ester complexes were prepored by ligand exchange reactions. To determine whether the ester band in Re-DMSA ester complexes is susceptible to cleavage by esterases, incubation experiments with tissue homogenates and plasma were carried out. (BBR)

  17. 21 CFR 172.854 - Polyglycerol esters of fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Polyglycerol esters of fatty acids. 172.854 Section... HUMAN CONSUMPTION Multipurpose Additives § 172.854 Polyglycerol esters of fatty acids. Polyglycerol esters of fatty acids, up to and including the decaglycerol esters, may be safely used in food in...

  18. Stability of a metabolizable ester bond in radioimmunoconjugates

    International Nuclear Information System (INIS)

    Arano, Yasushi; Wakisaka, Kouji; Mukai, Takahiro; Uezono, Takashi; Motonari, Hiroshi; Akizawa, Hiromichi; Kairiyama, Claudia; Ohmomo, Yoshiro; Tanaka, Chiaki; Ishiyama, Munetaka; Sakahara, Harumi; Konishi, Junji; Yokoyama, Akira

    1996-01-01

    Ester bonds have been used as metabolizable linkages to reduce radioactivity levels in non-target tissues following the administration of antibodies labeled with metallic radionuclides. In this radiochemical design of antibodies, while the ester bonds should be cleaved rapidly in non-target tissues, high stability of the ester bonds in plasma is also required to preserve target radioactivity levels. To assess the structural requirements to stabilize the ester bond, a new benzyl-EDTA-derived bifunctional chelating agent with an ester bond, (1-[4-[4-(2-maleimidoethoxy)succinamido]benzyl]ethylenediamine-N,N,N',N'- tetraacetic acid; MESS-Bz-EDTA), was developed. MESS-Bz-EDTA was coupled with a thiolated monoclonal antibody (OST7, IgG 1 ) prepared by reducing its disulfide bonds to introduce the ester bond close and proximal to the antibody molecule. For comparison, 1-[4-(5-maleimidopentyl)aminobenzyl]ethylenediamine-N,N,N',N'-tetraacetic acid (EMCS-Bz-EDTA) and meleimidoethyl 3-[ 131 I]iodohippurate (MIH) was coupled to OST7 under the same conjunction chemistry. When incubated in 50% murine plasma or a buffered-solution of neutral pH, OST7-MESS-Bz-EDTA- 111 In rapidly released the radioactivity, and more than 95% of the initial radioactivity was liberated after a 24 h incubation in both solutions, due to a cleavage of the ester bond. On the other hand, only about 20% of the radioactivity was released from OST7-MIH- 131 I in both solutions during the same incubation period. In mice biodistribution studies, while a slightly faster radioactivity clearance from the blood with less radioactivity levels in the liver and kidneys was observed with OST7-MIH- 131 I than with OST7-EMCS-Bz-EDTA- 111 In, OST7-MESS-Bz-EDTA- 111 In indicated radioactivity clearance from the blood much faster than and almost comparable to that of OST7-MIH- 131 I and succinamidobenzyl-EDTA- 111 In, respectively. These findings as well as previous findings on radiolabeled antibodies with ester bonds

  19. The 18-kilodalton Chlamydia trachomatis histone H1-like protein (Hc1) contains a potential N-terminal dimerization site and a C-terminal nucleic acid-binding domain

    DEFF Research Database (Denmark)

    Pedersen, LB; Birkelund, Svend; Holm, A

    1996-01-01

    The Chlamydia trachomatis histone H1-like protein (Hc1) is a DNA-binding protein specific for the metabolically inactive chlamydial developmental form, the elementary body. Hc1 induces DNA condensation in Escherichia coli and is a strong inhibitor of transcription and translation. These effects may......-hydroxysuccinimide ester), purified recombinant Hc1 was found to form dimers. The dimerization site was located in the N-terminal part of Hc1 (Hc1(2-57)). Moreover, circular dichroism measurements indicated an overall alpha-helical structure of this region. By using limited proteolysis, Southwestern blotting, and gel...

  20. Estereótipos e mulheres na cultura marroquina

    OpenAIRE

    Sadiqi,Fatima

    2008-01-01

    Estereótipos sobre as mulheres no Marrocos podem ser caracterizados como crenças culturais incompletas e inexatas mantidas por algumas pessoas e que se encontram inscritos em expressões lingüísticas ou em discursos subliminares. A cultura popular marroquina emprega representações poderosas para transmitir e sustentar tais estereótipos. Embora existam alguns estereótipos positivos, a maioria dos estereótipos sobre as mulheres no Marrocos é negativa e reflete ditames patriarcais subliminares qu...

  1. Methyl esters from vegetable oils with hydroxy fatty acids: Comparison of lesquerella and castor methyl esters

    Science.gov (United States)

    The search for alternative feedstocks for biodiesel as partial replacement for petrodiesel has recently extended to castor oil. In this work, the castor oil methyl esters were prepared and their properties determined in comparison to the methyl esters of lesquerella oil, which in turn is seen as alt...

  2. Environmentally friendly properties of vegetable oil methyl esters

    Directory of Open Access Journals (Sweden)

    Gateau Paul

    2005-07-01

    Full Text Available Measurements were carried out on Vegetable Oil Methyl Esters (VOME or FAME answering the most recent specifications. The products tested are RME (Rapeseed oil Methyl Ester, ERME (Erucic Rapeseed oil Methyl Esters, SME (Sunflower oil Methyl Esters, and HOSME (High Oleic Sunflower oil Methyl Esters. They contain more than 99.5% of fatty acid mono esters. The compositions are given. VOME are not volatile and they are not easily flammable. They are not soluble in water and they are biodegradable. According to the methods implemented for the determination of the German classification of substances hazardous to waters WGK, they are not toxic on mammals and unlike diesel fuel they are not toxic on fish, daphnia, algae and bacteria. The RME is not either toxic for shrimps. According to tests on rabbits, RME and SME are not irritating for the skin and the eyes. VOME display particularly attractive environmental properties.

  3. Preparation of Spirocyclic β-Proline Esters

    DEFF Research Database (Denmark)

    Fjelbye, Kasper; Marigo, Mauro; Clausen, Rasmus Prætorius

    2017-01-01

    A series of novel N-Bn-protected spirocyclic β-proline esters were prepared using [3+2] cycloaddition and subsequently converted into their corresponding aldehydes. In addition, two novel N-Cbz-protected spirocyclic β-proline esters were prepared using intramolecular cyclization starting from...

  4. Synthesis of Estolide 2-ethylhexyl Ester from Ricinus communis

    International Nuclear Information System (INIS)

    Nazrizawati Ahmad Tajuddin; Nor Habibah Rosli

    2013-01-01

    Estolide 2-ethylhexyl ester synthesized through condensation reaction between ricinoleic acid from castor oil (Ricinus communis) and lauric acid, and then capped with 2-ethylhexyl alcohol. The reaction was continuously conducted under vacuum for 24 hours. Product of 2-ethylhexyl ester was characterized by using Fourier Transform Infrared (FTIR) to determine functional group and Nuclear Magnetic Resonans (NMR) for structure's determination. The presence of ester group at 1738.23 cm -1 wavenumber indicates that the formation of estolide ester has occurred. The vibration peak of C-O at 1174.60 cm -1 and 1117.10 cm -1 support the formation of ester. The presence of CH 2 bending indicated the long-chain compound. The ester methine signal at 3.8669 ppm indicated the estolide linkage in the 1 H-NMR spectrum while the 13 C-NMR showed two carbonyl signals at 173.41 ppm for acid and 173.56 ppm for ester. (author)

  5. Phthalate esters in marine algae

    OpenAIRE

    Gezgin, Tuncay; Güven, Kasim Cemal; Akçin, Göksel

    2001-01-01

    Abstract o-Phthalate esters as diethyl phthalate, dibutyl phthalate, di-isobutyl phthalate and diethylhexyl phthalate were identified at surface and inner part of algae collected in the Bosphorus, as Ulva lactuca, Enteromorpha linza, Cystoseria barbata, Pterocladia capillaceaeand Ceramium rubrum. The same esters were also detected in seawater samples taken from the same area. Thus parallelism in pollution was noted between the algae and the surrounding seawater,

  6. Environmental effects of a discharge of drill cuttings contaminated with ester-based drilling muds in the North Sea

    International Nuclear Information System (INIS)

    Daan, R.; Booij, K.; Mulder, M.; Weerlee, E.M. van

    1996-01-01

    A field-monitoring program has been carried out to assess the environmental effects associated with drill cutting discharges at a drilling location in the North Sea, after drilling with ester-based muds. The study included a baseline survey just before drilling started and three postdrilling surveys, 1, 4, and 11 months after termination of drilling. During these surveys, ester concentrations and macrofauna densities were determined at distances between 75 and 3,000 m from the well. For the first and second postdrilling surveys, ester concentrations ranged between 2 and 4,700 mg·kg -1 dry sediment. During the third survey, esters were detected up to 200 m, with concentrations between 1 and 250 mg·kg -1 dry sediment. Between 500 and 3,000 m, ester concentrations were below detection level. The half-life was estimated as 133 d. This value reflects the composite effects of biodegradation and sediment relocation. During the second postdrilling survey, a reduced abundance as well as a reduced species richness of the macrofauna was observed up to 200 m from the well. Also, the presence of Capitella capitata was an obvious sign of disturbed sediment conditions in this area. A few species showed abundance gradients over the whole sampling transect and occurred in reduced abundance up to 500 or 1,000 m compared to the 3,000-m reference station. The third postdrilling survey clearly revealed effects at 75 to 200 m from the well. At distances ≥500 m, persistent effects could no longer be demonstrated. Although the results of the present study show that effects had not completely disappeared after 1 year, there are signs of recovery of the macrobenthos, because a reasonable number of species had recolonized the area in the vicinity of the well site, particularly at 200 m, in fairly high numbers

  7. Extraction and Liquid Chromatography-Tandem Mass Spectrometry Detection of 3-Monochloropropanediol Esters and Glycidyl Esters in Infant Formula.

    Science.gov (United States)

    Leigh, Jessica K; MacMahon, Shaun

    2016-12-14

    A method was developed for the extraction of fatty acid esters of 3-chloro-1,2-propanediol (3-MCPD) and glycidol from infant formula, followed by quantitative analysis of the extracts using liquid chromatography-tandem mass spectrometry (LC-MS/MS). These process-induced chemical contaminants are found in refined vegetable oils, and studies have shown that they are potentially carcinogenic and/or genotoxic, making their presence in edible oils (and processed foods containing these oils) a potential health risk. The extraction procedure involves a liquid-liquid extraction, where powdered infant formula is dissolved in water and extracted with ethyl acetate. Following shaking, centrifugation, and drying of the organic phase, the resulting fat extract is cleaned-up using solid-phase extraction and analyzed by LC-MS/MS. Method performance was confirmed by verifying the percent recovery of each 3-MCPD and glycidyl ester in a homemade powdered infant formula reference material. Average ester recoveries in the reference material ranged from 84.9 to 109.0% (0.6-9.5% RSD). The method was also validated by fortifying three varieties of commercial infant formulas with a 3-MCPD and glycidyl ester solution. Average recoveries of the esters across all concentrations and varieties of infant formula ranged from 88.7 to 107.5% (1.0-9.5% RSD). Based on the validation results, this method is suitable for producing 3-MCPD and glycidyl ester occurrence data in all commercially available varieties of infant formula.

  8. Gamma-aminobutyric acid esters. 1. Synthesis, brain uptake, and pharmacological studies of aliphatic and steroid esters of gamma-aminobutyric acid

    International Nuclear Information System (INIS)

    Shashoua, V.E.; Jacob, J.N.; Ridge, R.; Campbell, A.; Baldessarini, R.J.

    1984-01-01

    Labeled and unlabeled aliphatic and steroid esters of gamma-amino[U- 14 C]butyric acid (GABA) were synthesized and tested for their capacity to penetrate the blood-brain barrier and for evidence of central neuropharmacological activity in rodents. The uptake of the labeled 9,12,15-octadecatrienyl (linolenyl), 3-cholesteryl, 1-butyl, and the 9-fluoro-11 beta,17-dihydroxy-16 alpha-methyl-3,20-dioxopregna -1,4-dien-21-yl (dexamethasone) esters of GABA into mouse brain increased 2-, 25-, 74-, and 81-fold over GABA, respectively. The cholesteryl ester of GABA depressed the general motor activity of mice and rats in a dose-dependent manner, whereas the 1-butyl, linolenyl, and dexamethasone esters were inactive by this test. Studies of the rates of hydrolysis, GABA receptor binding capacity, and octanol/water partition coefficients indicated that pharmacological activity of the esters after entry into the central nervous system (CNS) was dependent on their capacity to release GABA by enzymatic hydrolysis and their lipid solubility

  9. Discrimination of processing grades of olive oil and other vegetable oils by monochloropropanediol esters and glycidyl esters

    NARCIS (Netherlands)

    Yan, Jing; Oey, Sergio B.; Leeuwen, van Stefan P.J.; Ruth, van Saskia M.

    2018-01-01

    In this study, the processing derived contaminants 2- and 3-monochloropropanediol (2- and 3-MCPD) esters and glycidyl esters (GEs) were analysed in 84 oil samples by GC–MS/MS for the discrimination of processing grades of olive oils as a potential authentication tool. Concentrations of 2- and 3-MCPD

  10. Effects of phorbol ester on mitogen-activated protein kinase kinase activity in wild-type and phorbol ester-resistant EL4 thymoma cells.

    Science.gov (United States)

    Gause, K C; Homma, M K; Licciardi, K A; Seger, R; Ahn, N G; Peterson, M J; Krebs, E G; Meier, K E

    1993-08-05

    Phorbol ester-sensitive and -resistant EL4 thymoma cell lines differ in their ability to activate mitogen-activated protein kinase (MAPK) in response to phorbol ester. Treatment of wild-type EL4 cells with phorbol ester results in the rapid activations of MAPK and pp90rsk kinase, a substrate for MAPK, while neither kinase is activated in response to phorbol ester in variant EL4 cells. This study examines the activation of MAPK kinase (MAPKK), an activator of MAPK, in wild-type and variant EL4 cells. Phosphorylation of a 40-kDa substrate, identified as MAPK, was observed following in vitro phosphorylation reactions using cytosolic extracts or Mono Q column fractions prepared from phorbol ester-treated wild-type EL4 cells. MAPKK activity coeluted with a portion of the inactive MAPK upon Mono Q anion-exchange chromatography, permitting detection of the MAPKK activity in fractions containing both kinases. This MAPKK activity was present in phorbol ester-treated wild-type cells, but not in phorbol ester-treated variant cells or in untreated wild-type or variant cells. The MAPKK from wild-type cells was able to activate MAPK prepared from either wild-type or variant cells. MAPKK activity could be stimulated in both wildtype and variant EL4 cells in response to treatment of cells with okadaic acid. These results indicate that the failure of variant EL4 cells to activate MAP kinase in response to phorbol ester is due to a failure to activate MAPKK. Therefore, the step that confers phorbol ester resistance to variant EL4 cells lies between the activation of protein kinase C and the activation of MAPKK.

  11. 21 CFR 172.852 - Glyceryl-lacto esters of fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Glyceryl-lacto esters of fatty acids. 172.852... HUMAN CONSUMPTION Multipurpose Additives § 172.852 Glyceryl-lacto esters of fatty acids. Glyceryl-lacto esters of fatty acids (the lactic acid esters of mono- and diglycerides) may be safely used in food in...

  12. Thermal and mechanical properties of fatty acid starch esters.

    Science.gov (United States)

    Winkler, H; Vorwerg, W; Rihm, R

    2014-02-15

    The current study examined thermal and mechanical properties of fatty acid starch esters (FASEs). All highly soluble esters were obtained by the sustainable, homogeneous transesterification of fatty acid vinyl esters in dimethylsulfoxide (DMSO). Casted films of products with a degree of substitution (DS) of 1.40-1.73 were compared with highly substituted ones (DS 2.20-2.63). All films were free of any plasticizer additives. Hydrophobic surfaces were characterized by contact angle measurements. Dynamic scanning calorimetry (DSC) and dynamic mechanical thermal analysis (DMTA) revealed thermal transitions (T(g), T(m)) which were influenced by the internal plasticizing effect of the ester groups. Thermal gravimetric analysis (TGA) measurements showed the increased thermal stability toward native starch. Tensile tests revealed the decreasing strength and stiffness of the products with increasing ester-group chain length while the elongation increased up to the ester group laurate and after that decreased. Esters of the longest fatty acids, palmitate and stearate turned out to be brittle materials due to super molecular structures of the ester chains such as confirmed by X-ray. Summarized products with a DS 1.40-1.73 featured more "starch-like" properties with tensile strength up to outstanding 43 MPa, while products with a DS >2 behaved more "oil-like". Both classes of esters should be tested as a serious alternative to commercial starch blends and petrol-based plastics. The term Cnumber is attributed to the number of total C-Atoms of the fatty acid (e.g. C6=Hexanoate). Copyright © 2013 Elsevier Ltd. All rights reserved.

  13. α-Imino Esters in Organic Synthesis: Recent Advances.

    Science.gov (United States)

    Eftekhari-Sis, Bagher; Zirak, Maryam

    2017-06-28

    α-Imino esters are useful precursors for the synthesis of a variety of types of natural and unnatural α-amino acid derivatives, with a wide range of biological activities. Due to the adjacent ester group, α-imino esters are more reactive relative to other types of imines and undergo different kinds of reactions, including organometallics addition, metal catalyzed vinylation and alkynylation, aza-Henry, aza-Morita-Baylis-Hillman, imino-ene, Mannich-type, and cycloaddition reactions, as well as hydrogenation and reduction. This review discusses the mechanism, scope, and applications of the reactions of α-imino esters and related compounds in organic synthesis, covering the literature from the last 12 years.

  14. Electro-optic investigation of the n-alkanethiol GaAs(001) interface: Surface phenomena and applications to photoluminescence-based biosensing

    Science.gov (United States)

    Marshall, Gregory M.

    Semiconductor surfaces coupled to molecular structures derived from organic chemistry form the basis of an emerging class of field-effect devices. In addition to molecular electronics research, these interfaces are developed for a variety of sensor applications in the electronic and optical domains. Of practical interest are self-assembled monolayers (SAMs) comprised of n-alkanethiols [HS(CH2)n], which couple to the GaAs(001) surface through S-GaAs covalent bond formation. These SAMs offer potential functionality in terms of the requisite sensor chemistry and the passivation effect such coupling is known to afford. In this thesis, the SAM-GaAs interface is investigated in the context of a photonic biosensor based on photoluminescence (PL) variation. The scope of the work is categorized into three parts: i) the structural and compositional analysis of the surface using X-ray photoelectron spectroscopy (XPS), ii) the investigation of electronic properties at the interface under equilibrium conditions using infrared (IR) spectroscopy, the Kelvin probe method, and XPS, and iii) the analysis of the electro-optic response under steady-state photonic excitation, specifically, the surface photovoltage (SPV) and PL intensity. Using a partial overlayer model of angle-resolved XPS spectra in which the component assignments are shown to be quantitatively valid, the coverage fraction of methyl-terminated SAMs is shown to exceed 90%. Notable among the findings are a low-oxide, Ga-rich surface with elemental As present in sub-monolayer quantities consistent with theoretical surface morphologies. Modal analysis of transmission IR spectra show that the SAM molecular order is sufficient to support a Beer-Lambert determination of the IR optical constants, which yields the observation of a SAM-specific absorbance enhancement. By correlation of the IR absorbance with the SAM dipole layer potential, the enhancement mechanism is attributed to the vibrational moments added by the

  15. The Au-S bond and SAM-protein contact in long-range electron transfer of pure and biomimetic metalloproteins via functionalized alkanethiol linkers

    DEFF Research Database (Denmark)

    Chi, Qijin; Ford, Michael J.; Halder, Arnab

    disentangled a wealth of data to identify the nature of the crucial Au-S contact, all suggesting prevalence of a Au(0)-thiyl radical unit. Molecular packing is further determined by the SAM molecular structure and involves binding either to Au-atoms mined out of the surface or directly to a flat surface. We...... functionalized alkanethiols have emerged as core linkers. We have studied molecular linking in the long-range ET (LRET) processes in detail using electrochemistry, in situ STM and AFM, and electronic structure computations. A focus is the electronic structure of the Au-S link and the SAM packing. We have...... is exceedingly sensitive to the structure of the thiol-based SAM molecules, testifying to the crucial importance of SAM packing and Au-S binding, and of the SAM link to the protein. Some of the subtleties are illustrated simpler by similar size (5-6 nm) nanoparticles (NPs). Biomimetic NPs must possess a certain...

  16. Origin of estradiol fatty acid esters in human ovarian follicular fluid.

    Science.gov (United States)

    Pahuja, S L; Kim, A H; Lee, G; Hochberg, R B

    1995-03-01

    The estradiol fatty acid esters are the most potent of the naturally occurring steroidal estrogens. These esters are present predominantly in fat, where they are sequestered until they are hydrolyzed by esterases. Thus they act as a preformed reservoir of estradiol. We have previously shown that ovarian follicular fluid from patients undergoing gonadotropin stimulation contains very high amounts of estradiol fatty acid esters (approximately 10(-7) M). The source of these esters is unknown. They can be formed by esterification of estradiol in the follicular fluid by lecithin:cholesterol acyltransferase (LCAT), or in the ovary by an acyl coenzyme A:acyltransferase. In order to determine which of these enzymatic processes is the source of the estradiol esters in the follicular fluid, we incubated [3H]estradiol with follicular fluid and cells isolated from human ovarian follicular fluid and characterized the fatty acid composition of the [3H]estradiol esters biosynthesized in each. In addition, we characterized the endogenous estradiol fatty acid esters in the follicular fluid and compared them to the biosynthetic esters. The fatty acid composition of the endogenous esters was different than those synthesized by the cellular acyl coenzyme A:acyltransferase, and the same as the esters synthesized by LCAT, demonstrating that the esters are produced in situ in the follicular fluid. Although the role of these estradiol esters in the ovary is not known, given their remarkable estrogenic potency it is highly probable that they have an important physiological role.

  17. Investigation of bifunctional ester additives for methanol-gasoline system

    International Nuclear Information System (INIS)

    Zhang, J.; Yang, C.; Tang, Y.; Du, Q.; Song, N.; Zhang, Z.

    2014-01-01

    To explore new and multifunctional additives for methanol-gasoline, tartaric ester were synthesized and screened as phase stabilizer and saturation vapor pressure depressor for methanol-gasoline. The effect of the esters structure on the efficiency was discussed. The results show that the stabilities of the blends depend on the length of the glycolic esters alkoxy group. In addition, the tartaric esters also can depress the saturation vapor pressure of methanol-gasoline effectively in M15. Effect of the structure on the efficiency was also discussed. (author)

  18. The 18-kilodalton Chlamydia trachomatis histone H1-like protein (Hc1) contains a potential N-terminal dimerization site and a C-terminal nucleic acid-binding domain

    DEFF Research Database (Denmark)

    Pedersen, Lotte Bang; Birkelund, S; Holm, A

    1996-01-01

    The Chlamydia trachomatis histone H1-like protein (Hc1) is a DNA-binding protein specific for the metabolically inactive chlamydial developmental form, the elementary body. Hc1 induces DNA condensation in Escherichia coli and is a strong inhibitor of transcription and translation. These effects may......-hydroxysuccinimide ester), purified recombinant Hc1 was found to form dimers. The dimerization site was located in the N-terminal part of Hc1 (Hc1(2-57)). Moreover, circular dichroism measurements indicated an overall alpha-helical structure of this region. By using limited proteolysis, Southwestern blotting, and gel...... retardation assays, Hc1(53-125) was shown to contain a domain capable of binding both DNA and RNA. Under the same conditions, Hc1(2-57) had no nucleic acid-binding activity. Electron microscopy of Hc1-DNA and Hc1(53-125)-DNA complexes revealed differences suggesting that the N-terminal part of Hc1 may affect...

  19. Ester Tuiksoo - Eesti esimene naissoost põllumajandusminister / Ester Tuiksoo ; interv. Toomas Verrev

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2007-01-01

    Ametist lahkuv põllumajandusminister Ester Tuiksoo räägib saadud juhtimiskogemusest, Euroopa Liidu ühise põllumajanduspoliitika juurutamisest, rahvuskala valimisest, Rahvaliidu käekäigust parlamendivalimistel

  20. 21 CFR 172.816 - Methyl glucoside-coconut oil ester.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl glucoside-coconut oil ester. 172.816 Section... HUMAN CONSUMPTION Multipurpose Additives § 172.816 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil ester may be safely used in food in accordance with the following conditions: (a) It is the...

  1. 21 CFR 178.3600 - Methyl glucoside-coconut oil ester.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Methyl glucoside-coconut oil ester. 178.3600... SANITIZERS Certain Adjuvants and Production Aids § 178.3600 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil ester identified in § 172.816(a) of this chapter may be safely used as a processing...

  2. ESTER: a new approach in modelling severe accidents

    International Nuclear Information System (INIS)

    Shepherd, I.; Jones, A.; Schmidt, F.

    1993-01-01

    ESTER is a set of codes for calculating phenomena during severe accidents in thermal reactors. It makes use of software tools that allow the data to be defined as a tree-structured data base and this data to be stored and retrieved by the code modules. The tools include generalized input and output routines that are independent of the particular code being used. Severe accident research codes are in a continual state of development and the structure of ESTER is such that modifications can be introduced easily and safely. The ESTER framework also facilitates the coupling together of codes. A preliminary version of ESTER containing a complete set of tools and a limited number of applications has already been released. 9 refs., 5 figs

  3. 21 CFR 172.848 - Lactylic esters of fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 3 2010-04-01 2009-04-01 true Lactylic esters of fatty acids. 172.848 Section 172... CONSUMPTION Multipurpose Additives § 172.848 Lactylic esters of fatty acids. Lactylic esters of fatty acids... prepared from lactic acid and fatty acids meeting the requirements of § 172.860(b) and/or oleic acid...

  4. An Improved Enzymatic Indirect Method for Simultaneous Determinations of 3-MCPD Esters and Glycidyl Esters in Fish Oils.

    Science.gov (United States)

    Miyazaki, Kinuko; Koyama, Kazuo

    2017-10-01

    The enzymatic indirect method for simultaneous determinations of 3-chloro-1, 2-propanediol fatty acid esters (3-MCPD-Es) and glycidyl fatty acid esters (Gly-Es) make use of lipase from Candida cylindracea (previously referred to as C. rugosa). Because of low substrate specificity of the lipase for esters of polyunsaturated fatty acids (PUFA), such as docosahexaenoic acid (DHA) and eicosapentaenoic acid (EPA), fish oils high in PUFAs are currently excluded from the range of application of the method. The objective of this study was to make the enzymatic indirect method applicable to fats and oils containing PUFAs. By using a Burkholderia cepacia lipase, and by removing sodium bromide from hydrolysis step and adding it after completion of the hydrolysis step, satisfactory recovery rates of 91-109% for 3-MCPD, and 91-110% for glycidol (Gly) were obtained from an EPA and DHA concentrated sardine oil, three DHA concentrated tuna oils, two fish oils, and five fish-oil based dietary supplements spiked with DHA-esters or oleic acid-esters of 3-MCPD and Gly at 20 mg/kg. Further, results from unspiked samples of seven fish oil based dietary supplements and five DHA concentrated tuna oils analyzed by the improved enzymatic indirect method were compared with the results analyzed by AOCS Cd 29a. For all 3-MCPD, 2-MCPD and Gly, the 95% confidence intervals determined by the weighted Deming regression for slopes and intercepts contained the value of 1 and 0, respectively. It was therefore concluded that the results from the two methods were not statistically different. These results suggest that fish oils high in PUFAs may be included in the range of application for the improved enzymatic indirect method for simultaneous determinations of 3-MCPD and Gly esters in fats and oils.

  5. Reaction and catalyst engineering to exploit kinetically controlled whole-cell multistep biocatalysis for terminal FAME oxyfunctionalization.

    Science.gov (United States)

    Schrewe, Manfred; Julsing, Mattijs K; Lange, Kerstin; Czarnotta, Eik; Schmid, Andreas; Bühler, Bruno

    2014-09-01

    The oxyfunctionalization of unactivated C−H bonds can selectively and efficiently be catalyzed by oxygenase-containing whole-cell biocatalysts. Recombinant Escherichia coli W3110 containing the alkane monooxygenase AlkBGT and the outer membrane protein AlkL from Pseudomonas putida GPo1 have been shown to efficiently catalyze the terminal oxyfunctionalization of renewable fatty acid methyl esters yielding bifunctional products of interest for polymer synthesis. In this study, AlkBGTL-containing E. coli W3110 is shown to catalyze the multistep conversion of dodecanoic acid methyl ester (DAME) via terminal alcohol and aldehyde to the acid, exhibiting Michaelis-Menten-type kinetics for each reaction step. In two-liquid phase biotransformations, the product formation pattern was found to be controlled by DAME availability. Supplying DAME as bulk organic phase led to accumulation of the terminal alcohol as the predominant product. Limiting DAME availability via application of bis(2-ethylhexyl)phthalate (BEHP) as organic carrier solvent enabled almost exclusive acid accumulation. Furthermore, utilization of BEHP enhanced catalyst stability by reducing toxic effects of substrate and products. A further shift towards the overoxidized products was achieved by co-expression of the gene encoding the alcohol dehydrogenase AlkJ, which was shown to catalyze efficient and irreversible alcohol to aldehyde oxidation in vivo. With DAME as organic phase, the aldehyde accumulated as main product using resting cells containing AlkBGT, AlkL, as well as AlkJ. This study highlights the versatility of whole-cell biocatalysis for synthesis of industrially relevant bifunctional building blocks and demonstrates how integrated reaction and catalyst engineering can be implemented to control product formation patterns in biocatalytic multistep reactions. © 2014 Wiley Periodicals, Inc.

  6. Toughened cyanate ester alloys via reaction-induced phase separation; Hanno yuhatsugataso bunkai ni yoru taishogekisei cyanate ester alloy

    Energy Technology Data Exchange (ETDEWEB)

    Hirohata, T.; Kuroda, M.; Nishimura, A. [Sumitomo Electric Industries, Ltd., Osaka (Japan); Inoue, T. [Tokyo Institute of Technology, Tokyo (Japan)

    1998-03-15

    For the purpose of toughening the matrices of fiber-reinforced plastics (FRPs), the effect of thermosetting/thermoplastic polymer alloys based on cyanate ester alloys is investigated. In the experiment, materials are heated and then allowed to set, which are mixtures of 87.0-43.5wt% of cyanate ester resin, 0-43.5wt% of epoxy resin, and 13.0wt% of soluble polyimide. FRP properties are examined by measuring the after-shock compressive strength, flexural elasticity and flaxural strength, and by performing morphology observation. It is then found that a cyanate ester/soluble polyimide system forms a polymer alloy with phase separation, that its glass transition temperature does not drop, and that the rupture strength is increased approximately twice. A carbon fiber-reinforced plastic (CFRP) incorporating this system is twice higher in after-shock compression strength than a CFRP incorporating a cyanate ester. The system withstands high temperatures, retaining at 200degC approximately 90% of the elastic modulus it exhibits at room temperature. 15 refs., 16 figs.

  7. Segmented poly(ether ester)s and poly(ether ester amide)s for use in tissue engineering

    OpenAIRE

    Deschamps, A.A.

    2002-01-01

    The objective of the studies described in this thesis is to investigate the applicability of these slowly degradable thermoplastic elastomers as scaffolds for tissue engineering, with emphasis on their phase separation and degradation properties. A second thermoplastic elastomer in which the terephthalic moieties have been replaced by ester-amide segments, is also investigated for use in scaffolding.

  8. Potential Grape-Derived Contributions to Volatile Ester Concentrations in Wine

    Directory of Open Access Journals (Sweden)

    Paul K. Boss

    2015-04-01

    Full Text Available Grape composition affects wine flavour and aroma not only through varietal compounds, but also by influencing the production of volatile compounds by yeast. C9 and C12 compounds that potentially influence ethyl ester synthesis during fermentation were studied using a model grape juice medium. It was shown that the addition of free fatty acids, their methyl esters or acyl-carnitine and acyl-amino acid conjugates can increase ethyl ester production in fermentations. The stimulation of ethyl ester production above that of the control was apparent when lower concentrations of the C9 compounds were added to the model musts compared to the C12 compounds. Four amino acids, which are involved in CoA biosynthesis, were also added to model grape juice medium in the absence of pantothenate to test their ability to influence ethyl and acetate ester production. β-Alanine was the only one shown to increase the production of ethyl esters, free fatty acids and acetate esters. The addition of 1 mg∙L−1 β-alanine was enough to stimulate production of these compounds and addition of up to 100 mg∙L−1 β-alanine had no greater effect. The endogenous concentrations of β-alanine in fifty Cabernet Sauvignon grape samples exceeded the 1 mg∙L−1 required for the stimulatory effect on ethyl and acetate ester production observed in this study.

  9. Potential grape-derived contributions to volatile ester concentrations in wine.

    Science.gov (United States)

    Boss, Paul K; Pearce, Anthony D; Zhao, Yanjia; Nicholson, Emily L; Dennis, Eric G; Jeffery, David W

    2015-04-29

    Grape composition affects wine flavour and aroma not only through varietal compounds, but also by influencing the production of volatile compounds by yeast. C9 and C12 compounds that potentially influence ethyl ester synthesis during fermentation were studied using a model grape juice medium. It was shown that the addition of free fatty acids, their methyl esters or acyl-carnitine and acyl-amino acid conjugates can increase ethyl ester production in fermentations. The stimulation of ethyl ester production above that of the control was apparent when lower concentrations of the C9 compounds were added to the model musts compared to the C12 compounds. Four amino acids, which are involved in CoA biosynthesis, were also added to model grape juice medium in the absence of pantothenate to test their ability to influence ethyl and acetate ester production. β-Alanine was the only one shown to increase the production of ethyl esters, free fatty acids and acetate esters. The addition of 1 mg∙L(-1) β-alanine was enough to stimulate production of these compounds and addition of up to 100 mg∙L(-1) β-alanine had no greater effect. The endogenous concentrations of β-alanine in fifty Cabernet Sauvignon grape samples exceeded the 1 mg∙L(-1) required for the stimulatory effect on ethyl and acetate ester production observed in this study.

  10. Preparation of polyol esters based on vegetable and animal fats.

    Science.gov (United States)

    Gryglewicz, S; Piechocki, W; Gryglewicz, G

    2003-03-01

    The possibility of using some natural fats: rapeseed oil, olive oil and lard, as starting material for the preparation of neopentyl glycol (NPG) and trimethylol propane (TMP) esters is reported. The syntheses of final products were performed by alcoholysis of fatty acid methyl esters, obtained from natural fats studied, with the appropriate polyhydric alcohol using calcium methoxide as a catalyst. The basic physicochemical properties of the NPG and TMP esters synthesized were the following: viscosity at 40 degrees C in the range of 13.5-37.6 cSt, pour point between -10.5 and -17.5 degrees C and very high viscosity indices, higher than 200. Generally, the esters of neopentyl alcohols were characterized by higher stability in thermo-oxidative conditions in comparison to native triglycerides. Due to the low content of polyunsaturated acids, the olive oil based esters showed the highest thermo-oxidative resistance. Also, methyl esters of fatty acids of lard would constitute a good raw material for the synthesis of lubricating oils, provided that their saturated acids content was lowered. This permits synthesis of NPG and TMP esters with a lower pour point (below -10 degrees C) than natural lard (+33 degrees C).

  11. Occurrence of 3-monochloropropanediol esters and glycidyl esters in commercial infant formulas in the United States.

    Science.gov (United States)

    Leigh, Jessica; MacMahon, Shaun

    2017-03-01

    This work presents occurrence data for fatty acid esters of 3-chloro-1,2-propanediol (3-MCPD) and glycidol in 98 infant formula samples purchased in the United States. These contaminants are considered potentially carcinogenic and/or genotoxic, making their presence in refined oils and foods a potential health risk. Recently, attention has focused on methodology to quantify MCPD and glycidyl esters in infant formula for risk-assessment purposes. Occurrence data for 3-MCPD and glycidyl esters were produced using a procedure for extracting fat from infant formula and an LC-MS/MS method for analysing fat extracts for intact esters. Infant formulas were produced by seven manufacturers, five of which use palm oil and/or palm olein in their formulations. In formulas containing palm/palm olein, concentrations for bound 3-MCPD and glycidol ranged from 0.021 to 0.92 mg kg - 1 (ppm) and from 3-MCPD and glycidol concentrations ranged from 0.072 to 0.16 mg kg - 1 (ppm) and from 0.005 to 0.15 mg kg - 1 (ppm), respectively. Although formulas from manufacturers A and G did not contain palm/palm olein, formulas from manufacturer E (containing palm olein) had the lowest concentrations of bound 3-MCPD and glycidol, demonstrating the effectiveness of industrial mitigation strategies.

  12. A Comparison Study: The New Extended Shelf Life Isopropyl Ester PMR Technology versus The Traditional Methyl Ester PMR Approach

    Science.gov (United States)

    Alston, William B.; Scheiman, Daniel A.; Sivko, Gloria S.

    2005-01-01

    Polymerization of Monomeric Reactants (PMR) monomer solutions and carbon cloth prepregs of PMR II-50 and VCAP-75 were prepared using both the traditional limited shelf life methanol based PMR approach and a novel extended shelf life isopropanol based PMR approach. The methyl ester and isopropyl ester based PMR monomer solutions and PMR prepregs were aged for up to four years at freezer and room temperatures. The aging products formed were monitored using high pressure liquid chromatography (HPLC). The composite processing flow characteristics and volatile contents of the aged prepregs were also correlated versus room temperature storage time. Composite processing cycles were developed and six ply cloth laminates were fabricated with prepregs after various extended room temperature storage times. The composites were then evaluated for glass transition temperature (Tg), thermal decomposition temperature (Td), initial flexural strength (FS) and modulus (FM), long term (1000 hours at 316 C) thermal oxidative stability (TOS), and retention of FS and FM after 1000 hours aging at 316 C. The results for each ester system were comparable. Freezer storage was found to prevent the formation of aging products for both ester systems. Room temperature storage of the novel isopropyl ester system increased PMR monomer solution and PMR prepreg shelf life by at least an order of magnitude while maintaining composite properties.

  13. Synthesis of TMP-ester biolubricant basestock from palm stearin fatty acids

    Science.gov (United States)

    Fadzel, Fatimatuzzahraa Mohd; Salimon, Jumat; Derawi, Darfizzi

    2018-04-01

    A potential biolubricant; TMP-ester was produced via esterification of fatty acids (FA) from palm stearin (PS) with trimethylolpropane (TMP). The synthesis was conducted at four conditions; temperature, time, molar ratio of FA:TMP and H2SO4 as catalyst (by percent based on the weight of FA and TMP) that are 150 °C, 2 hours, 4:1 and 1% of H2SO4 respectively. The composition of ester produced was determined using gas chromatography (GC-FID). The presence of ester group was confirmed by the means of FTIR by the existence of strong carboxyl band of ester, v(C=O) at 1746cm-1 and 1H and 13C NMR spectroscopy shows the chemical shift, δ of ester, C=O at 2.27-2.31 ppm and 173.45 ppm accordingly. From the esterification reaction, 95% product of TMP-ester was formed. The thermal and oxidative stability of TMP-ester is 200°C.

  14. Naturally Occurring Cinnamic Acid Sugar Ester Derivatives

    Directory of Open Access Journals (Sweden)

    Yuxin Tian

    2016-10-01

    Full Text Available Cinnamic acid sugar ester derivatives (CASEDs are a class of natural product with one or several phenylacrylic moieties linked with the non-anomeric carbon of a glycosyl skeleton part through ester bonds. Their notable anti-depressant and brains protective activities have made them a topic of great interest over the past several decades. In particular the compound 3′,6-disinapoylsucrose, the index component of Yuanzhi (a well-known Traditional Chinese Medicine or TCM, presents antidepressant effects at a molecular level, and has become a hotspot of research on new lead drug compounds. Several other similar cinnamic acid sugar ester derivatives are reported in traditional medicine as compounds to calm the nerves and display anti-depression and neuroprotective activity. Interestingly, more than one third of CASEDs are distributed in the family Polygalaceae. This overview discusses the isolation of cinnamic acid sugar ester derivatives from plants, together with a systematic discussion of their distribution, chemical structures and properties and pharmacological activities, with the hope of providing references for natural product researchers and draw attention to these interesting compounds.

  15. Spontaneous Self-Assembly of Fully Protected Ester 1:1 [α/α-Nα-Bn-hydrazino] Pseudodipeptides into a Twisted Parallel β-Sheet in the Crystal State.

    Science.gov (United States)

    Romero, Eugénie; Moussodia, Ralph-Olivier; Kriznik, Alexandre; Wenger, Emmanuel; Acherar, Samir; Jamart-Grégoire, Brigitte

    2016-10-07

    Previous studies have demonstrated that amidic α/β-pseudodipeptides, 1:1 [α/α-N α -Bn-hydrazino], have the ability to fold via a succession of γ-turn (C 7 pseudocycle) and hydrazinoturn in CDCl 3 solution, their amide terminals enabling the formation of an intramolecular H-bond network. Despite their lack of a primary amide terminals allowing the formation of the hydrazinoturn, their ester counterparts 1-4 were proven to self-assemble into C 6 and C 7 pseudocycles by intramolecular H-bonds in solution state and into an uncommon twisted parallel β-sheet through intermolecular H-bonding in the crystal state to form a supramolecular helix, with eight molecules needed to complete a full 360° rotation. Such self-organization (with eight molecules) has only been observed in a specific α/α-pseudodipeptide, depsipeptide (Boc-Leu-Lac-OEt). Relying on IR absorption, NMR, X-ray diffraction, and CD analyses, the aim of this study was to demonstrate that stereoisomers of ester 1:1 [α/α-N α -Bn-hydrazino] pseudodipeptides 1-4 are able to self-assemble into this β-helical structure. The absolute configuration of the asymmetric C α -atom of the α-amino acid residue influences the left- or right-handed twist without changing the pitch of the formed helix.

  16. Preparation and characterization of aliphatic diphenyl esters intended as precursors for polyesters

    DEFF Research Database (Denmark)

    Hvilsted, S.; Andruzzi, F.; Cerrai, P.

    1991-01-01

    An extensive number of aliphatic diphenyl esters, C6H5OOC(CH2)nCOOC6H5 (n = O,...,8,10,11,12,14), have been prepared in pure form. The crystalline melting points these esters exhibit an odd-even temperature behaviour, with the higher-melting even series (n even) displaying a minimum for n = 8 while...... based on similar data from phenyl esters, interpreted as the results of an apparent macrocyclic conformation of the larger diphenyl esters. High-performance size exclusion chromatography (s.e.c.) of diphenyl esters, phenyl esters, aromatic and linear hydrocarbons in tetrahydrofuran, toluene...

  17. Kinetics of electron transfer through ferrocene-terminated alkanethiol monolayers on gold

    Energy Technology Data Exchange (ETDEWEB)

    Smalley, J.F.; Feldberg, S.W.; Newton, M.D.; Liu, Y.P. [Brookhaven National Lab., Upton, NY (United States); Chidsey, C.E.D.; Linford, M.R. [Stanford Univ., CA (United States)

    1995-08-31

    The kinetics of electron transfer between a substrate gold electrode and a self-assembled monolayer formed from CH{sub 3}(CH{sub 2}){sub n-1}SH and ({eta}{sup 5} C{sub 5}H{sub 5})Fe ({eta}{sup 5}-C{sub 5}H{sub 4})CO{sub 2}(CH{sub 2}){sub n}SH were studied as a function of n, the number of methylenes in the alkyl chain tethering the ferrocene moiety to the electrode, using the indirect laser-induced temperature jump method (ILIT). For 5 {<=} n {<=} 9 the standard electron-transfer rate constants vary according to {kappa}{sub {tau}a,n=0} exp[-{beta}{sub n}n] where {kappa}{sub {tau}a,n=0} is the (extrapolated) rate constant for the electron transfer at n = 0. At {Tau} = 25{degree}C, {kappa}{sub {tau}a,n} 0 {approx_equal} 6 x 10{sup 8} s{sup -1} and {beta}{sub n} = 1.21 x 0.05. The ILIT method allows rates to be measured that are too fast to be measured by conventional chronoamperometry at a macroelectrode, which is limited to rate constants of {<=} 10{sup 4} s{sup -1}. Using a Marcus formalism, the reorganization energy, {lambda}, for the electron-transfer process at a given n was determined from the slope of an Arrhenius plot over the temperature range 15-55{degree}C. Values of {lambda} determined from Arrhenius slopes for n = 8 and 9 using ILIT are in reasonable agreement with the value of {lambda} previously deduced from the potential dependence of the rate constant for n = 16. 39 refs., 13 figs., 3 tabs.

  18. Method for the determination of natural ester-type gum bases used as food additives via direct analysis of their constituent wax esters using high-temperature GC/MS.

    Science.gov (United States)

    Tada, Atsuko; Ishizuki, Kyoko; Yamazaki, Takeshi; Sugimoto, Naoki; Akiyama, Hiroshi

    2014-07-01

    Natural ester-type gum bases, which are used worldwide as food additives, mainly consist of wax esters composed of long-chain fatty acids and long-chain fatty alcohols. There are many varieties of ester-type gum bases, and thus a useful method for their discrimination is needed in order to establish official specifications and manage their quality control. Herein is reported a rapid and simple method for the analysis of different ester-type gum bases used as food additives by high-temperature gas chromatography/mass spectrometry (GC/MS). With this method, the constituent wax esters in ester-type gum bases can be detected without hydrolysis and derivatization. The method was applied to the determination of 10 types of gum bases, including beeswax, carnauba wax, lanolin, and jojoba wax, and it was demonstrated that the gum bases derived from identical origins have specific and characteristic total ion chromatogram (TIC) patterns and ester compositions. Food additive gum bases were thus distinguished from one another based on their TIC patterns and then more clearly discriminated using simultaneous monitoring of the fragment ions corresponding to the fatty acid moieties of the individual molecular species of the wax esters. This direct high-temperature GC/MS method was shown to be very useful for the rapid and simple discrimination of varieties of ester-type gum bases used as food additives.

  19. Method for the determination of natural ester-type gum bases used as food additives via direct analysis of their constituent wax esters using high-temperature GC/MS

    Science.gov (United States)

    Tada, Atsuko; Ishizuki, Kyoko; Yamazaki, Takeshi; Sugimoto, Naoki; Akiyama, Hiroshi

    2014-01-01

    Natural ester-type gum bases, which are used worldwide as food additives, mainly consist of wax esters composed of long-chain fatty acids and long-chain fatty alcohols. There are many varieties of ester-type gum bases, and thus a useful method for their discrimination is needed in order to establish official specifications and manage their quality control. Herein is reported a rapid and simple method for the analysis of different ester-type gum bases used as food additives by high-temperature gas chromatography/mass spectrometry (GC/MS). With this method, the constituent wax esters in ester-type gum bases can be detected without hydrolysis and derivatization. The method was applied to the determination of 10 types of gum bases, including beeswax, carnauba wax, lanolin, and jojoba wax, and it was demonstrated that the gum bases derived from identical origins have specific and characteristic total ion chromatogram (TIC) patterns and ester compositions. Food additive gum bases were thus distinguished from one another based on their TIC patterns and then more clearly discriminated using simultaneous monitoring of the fragment ions corresponding to the fatty acid moieties of the individual molecular species of the wax esters. This direct high-temperature GC/MS method was shown to be very useful for the rapid and simple discrimination of varieties of ester-type gum bases used as food additives. PMID:25473499

  20. Wax ester profiling of seed oil by nano-electrospray ionization tandem mass spectrometry

    Science.gov (United States)

    2013-01-01

    Background Wax esters are highly hydrophobic neutral lipids that are major constituents of the cutin and suberin layer. Moreover they have favorable properties as a commodity for industrial applications. Through transgenic expression of wax ester biosynthetic genes in oilseed crops, it is possible to achieve high level accumulation of defined wax ester compositions within the seed oil to provide a sustainable source for such high value lipids. The fatty alcohol moiety of the wax esters is formed from plant-endogenous acyl-CoAs by the action of fatty acyl reductases (FAR). In a second step the fatty alcohol is condensed with acyl-CoA by a wax synthase (WS) to form a wax ester. In order to evaluate the specificity of wax ester biosynthesis, analytical methods are needed that provide detailed wax ester profiles from complex lipid extracts. Results We present a direct infusion ESI-tandem MS method that allows the semi-quantitative determination of wax ester compositions from complex lipid mixtures covering 784 even chain molecular species. The definition of calibration prototype groups that combine wax esters according to their fragmentation behavior enables fast quantitative analysis by applying multiple reaction monitoring. This provides a tool to analyze wax layer composition or determine whether seeds accumulate a desired wax ester profile. Besides the profiling method, we provide general information on wax ester analysis by the systematic definition of wax ester prototypes according to their collision-induced dissociation spectra. We applied the developed method for wax ester profiling of the well characterized jojoba seed oil and compared the profile with wax ester-accumulating Arabidopsis thaliana expressing the wax ester biosynthetic genes MaFAR and ScWS. Conclusions We developed a fast profiling method for wax ester analysis on the molecular species level. This method is suitable to screen large numbers of transgenic plants as well as other wax ester samples

  1. 21 CFR 573.640 - Methyl esters of higher fatty acids.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methyl esters of higher fatty acids. 573.640... ANIMALS Food Additive Listing § 573.640 Methyl esters of higher fatty acids. The food additive methyl esters of higher fatty acids may be safely used in animal feeds in accordance with the following...

  2. Optimal Use of Plant Stanol Ester in the Management of Hypercholesterolemia

    Directory of Open Access Journals (Sweden)

    Susanna Rosin

    2015-01-01

    Full Text Available Plant stanol ester is a natural compound which is used as a cholesterol-lowering ingredient in functional foods and food supplements. The safety and efficacy of plant stanol ester have been confirmed in more than 70 published clinical studies and the ingredient is a well-established and widely recommended dietary measure to reduce serum cholesterol. Daily intake of 2 g plant stanols as plant stanol ester lowers LDL-cholesterol by 10%, on average. In Europe, foods with added plant stanol ester have been on the market for 20 years, and today such products are also available in many Asian and American countries. Despite the well-documented efficacy, the full potential in cholesterol reduction may not be reached if plant stanol ester is not used according to recommendations. This review therefore concentrates on the optimal use of plant stanol ester as part of dietary management of hypercholesterolemia. For optimal cholesterol lowering aiming at a lower risk of cardiovascular disease, plant stanol ester should be used daily, in sufficient amounts, with a meal and in combination with other recommended dietary changes.

  3. Catalytic Oxidation of Allylic Alcohols to Methyl Esters

    DEFF Research Database (Denmark)

    Gallas-Hulin, Agata; Kotni, Rama Krishna; Nielsen, Martin

    2017-01-01

    Aerobic oxidation of allylic alcohols to methyl esters using gold nanoparticles supported on different metal oxide carriers has been performed successfully under mild conditions (room temperature, 0.1 MPa O2) without significant loss of catalytic activity. The effects of different reaction...... parameters are studied to find the suitable reaction conditions. All catalysts are characterised by XRD, XRF and TEM. Among these catalysts, Au/TiO2 showed the most efficient catalytic activity towards the selective oxidation of allylic alcohols to the corresponding esters. Moreover, the same Au/TiO2...... to synthesize methyl esters from allylic alcohols....

  4. Transformation of Unsaturated Fatty Acids/Esters to Corresponding Keto Fatty Acids/Esters by Aerobic Oxidation with Pd(II)/Lewis Acid Catalyst.

    Science.gov (United States)

    Senan, Ahmed M; Zhang, Sicheng; Zeng, Miao; Chen, Zhuqi; Yin, Guochuan

    2017-08-16

    Utilization of renewable biomass to partly replace the fossil resources in industrial applications has attracted attention due to the limited fossil feedstock with the increased environmental concerns. This work introduced a modified Wacker-type oxidation for transformation of unsaturated fatty acids/esters to the corresponding keto fatty acids/esters, in which Cu 2+ cation was replaced with common nonredox metal ions, that is, a novel Pd(II)/Lewis acid (LA) catalyst. It was found that adding nonredox metal ions can effectively promote Pd(II)-catalyzed oxidation of unsaturated fatty acids/esters to the corresponding keto fatty acids/esters, even much better than Cu 2+ , and the promotional effect is highly dependent on the Lewis acidity of added nonredox metal ions. The improved catalytic efficiency is attributed to the formation of heterobimetallic Pd(II)/LA species, and the oxidation mechanism of this Pd(II)/LA catalyst is also briefly discussed.

  5. Effect of temperature stress on protein methyl esters

    International Nuclear Information System (INIS)

    Welch, W.; Kracaw, K.

    1986-01-01

    Protein methyl esters have been implicated in a number of physiological processes. They have measured the effect of temperature stress on the levels of protein methyl esters in the mesophilic fungus Penicillium chrysogenum (PCPS) and the thermophilic fungus P. duponti (PD). PD and PCPS were incubated with [methyl- 3 H]methionine. The mycelia were collected by filtration, frozen in liquid nitrogen and ground to a fine powder. The nitrogen powder was extracted with either phosphate buffer or with SDS, glycerol, phosphate, 2-mercaptoethanol. Insoluble material was removed by centrifugation. The supernatants were assayed for protein methyl esters. The released [ 3 H]methanol was extracted into toluene:isoamyl alcohol (3:2) and quantitated by liquid scintillation. The production of volatile methanol was confirmed by use of Conway diffusion cells. Soluble proteins accounted for about one-fourth of the total protein methyl ester extracted by SDS. In PCPS, the SDS extracted proteins have about three times the level of esterification of the soluble proteins whereas in PD there is little difference between soluble and SDS extracted protein. The level of protein esterification in PD is about one-tenth that observed in PCPS. Temperature stress caused large changes in the level of protein esterification. The data suggest protein methyl esters may contribute to the adaptation to environmental stress

  6. Lipase catalyzed ester synthesis for food processing industries

    Directory of Open Access Journals (Sweden)

    Aravindan Rajendran

    2009-02-01

    Full Text Available Lipases are one of the most important industrial biocatalyst which catalyzes the hydrolysis of lipids. It can also reverse the reaction at minimum water activity. Because of this pliable nature, it is widely exploited to catalyze the diverse bioconversion reactions, such as hydrolysis, esterification, interesterification, alcoholysis, acidolysis and aminolysis. The property to synthesize the esters from the fatty acids and glycerol promotes its use in various ester synthesis. The esters synthesized by lipase finds applications in numerous fields such as biodiesel production, resolution of the recemic drugs, fat and lipid modification, flavour synthesis, synthesis of enantiopure pharmaceuticals and nutraceuticals. It plays a crucial role in the food processing industries since the process is unaffected by the unwanted side products. Lipase modifications such as the surfactant coating, molecular imprinting to suit for the non-aqueous ester synthesis have also been reported. This review deals with lipase catalyzed ester synthesis, esterification strategies, optimum conditions and their applications in food processing industries.Lipases são catalizadores industriais dos mais importantes, os quais catalizam a hidrólise de lipídeos. Também podem reverter a reação a um mínimo de atividade de água. Devido sua natureza flexível, é amplamente explorada para catalizar uma diversidade de reações de bioconversão como hidrólise, esterificação, interesterificação, alcoólise, acidólise e aminólise. A propriedade de síntese de esteres a partir de ácidos graxos e glicerol promoveu seu uso em várias sínteses de esteres. Os esteres sintetizados por lipases encontram aplicação em numerosos campos como a produção de biodiesel, resolução de drogas racêmicas, modificação de gorduras e lipídios, sintese de aromas, síntese de produtos farmacêuticos enantiopuro e nutracêuticos. As lipases possuem um papel crucial nas indústrias de

  7. Method for separating mono- and di-octylphenyl phosphoric acid esters

    International Nuclear Information System (INIS)

    Arnold, W.D. Jr.

    1977-01-01

    A method for separating mono-octylphenyl phosphoric acid ester and di-octylphenyl phosphoric acid ester from a mixture thereof comprises reacting the ester mixture with a source of lithium or sodium ions to form a mixture of the phosphate salts; contacting the salt mixture with an organic solvent which causes the dioctylphenyl phosphate salt to be dissolved in the organic solvent phase and the mono-octylphenyl phosphate salt to exist in a solid phase; separating the phases; recovering the phosphate salts from their respective phases; and acidifying the recovered salts to form the original phosphoric acid esters

  8. Microbial synthesis of a branched-chain ester platform from organic waste carboxylates

    Directory of Open Access Journals (Sweden)

    Donovan S. Layton

    2016-12-01

    Full Text Available Processing of lignocellulosic biomass or organic wastes produces a plethora of chemicals such as short, linear carboxylic acids, known as carboxylates, derived from anaerobic digestion. While these carboxylates have low values and are inhibitory to microbes during fermentation, they can be biologically upgraded to high-value products. In this study, we expanded our general framework for biological upgrading of carboxylates to branched-chain esters by using three highly active alcohol acyltransferases (AATs for alcohol and acyl CoA condensation and modulating the alcohol moiety from ethanol to isobutanol in the modular chassis cell. With this framework, we demonstrated the production of an ester library comprised of 16 out of all 18 potential esters, including acetate, propionate, butanoate, pentanoate, and hexanoate esters, from the 5 linear, saturated C2-C6 carboxylic acids. Among these esters, 5 new branched-chain esters, including isobutyl acetate, isobutyl propionate, isobutyl butyrate, isobutyl pentanoate, and isobutyl hexanoate were synthesized in vivo. During 24 h in situ fermentation and extraction, one of the engineered strains, EcDL208 harnessing the SAAT of Fragaria ananassa produced ~63 mg/L of a mixture of butyl and isobutyl butyrates from glucose and butyrate co-fermentation and ~127 mg/L of a mixture of isobutyl and pentyl pentanoates from glucose and pentanoate co-fermentation, with high specificity. These butyrate and pentanoate esters are potential drop-in liquid fuels. This study provides better understanding of functional roles of AATs for microbial biosynthesis of branched-chain esters and expands the potential use of these esters as drop-in biofuels beyond their conventional flavor, fragrance, and solvent applications. Keywords: Carboxylate platform, Ester platform, Branched-chain ester, Modular cell, Biological upgrading, Organic waste, Lignocellulosic biomass, Isobutyl esters

  9. Rapid NIR determination of alkyl esters in virgin olive oil

    International Nuclear Information System (INIS)

    Cayuela, J.A.

    2017-01-01

    The regulation of The European Union for olive oil and olive pomace established the limit of 35 mg·kg-1 for fatty acids ethyl ester contents in extra virgin olive oils, from grinding seasons after 2016. In this work, predictive models have been established for measuring fatty acid ethyl and methyl esters and to measure the total fatty acid alkyl esters based on near infrared spectroscopy (NIRS), and used successfully for this purpose. The correlation coefficients from the external validation exercises carried out with these predictive models ranged from 0.84 to 0.91. Different classification tests using the same models for the thresholds 35 mg·kg-1 for fatty acid ethyl esters and 75 mg·kg-1 for fatty acid alkyl esters provided success percentages from 75.0% to 95.2%. [es

  10. Development of tartaric esters as bifunctional additives of methanol-gasoline.

    Science.gov (United States)

    Zhang, Jie; Yang, Changchun; Tang, Ying; Zhou, Rui; Wang, Xiaoli; Xu, Lianghong

    2014-01-01

    Methanol has become an alternative fuel for gasoline, which is facing a rapidly rising world demand with a limited oil supply. Methanol-gasoline has been used in China, but phase stability and vapor lock still need to be resolved in methanol-gasoline applications. In this paper, a series of tartaric esters were synthesized and used as phase stabilizers and saturation vapor pressure depressors for methanol-gasoline. The results showed that the phase stabilities of tartaric esters for methanol-gasoline depend on the length of the alkoxy group. Several tartaric esters were found to be effective in various gasoline-methanol blends, and the tartaric esters display high capacity to depress the saturation vapor pressure of methanol-gasoline. According to the results, it can be concluded that the tartaric esters have great potential to be bifunctional gasoline-methanol additives.

  11. Analysis of Adipate Ester Contents in PVC Plastics

    DEFF Research Database (Denmark)

    Berg, Rolf W.

    2006-01-01

    Plasticizers are needed in flexible PVC (PolyVinylChloride) products. There is serious concern that commonly used phthalate esters may harm life reproduction systems. To avoid the problems, instead adipate di-esters (AEs) of C8 to C10 alcohols are used as higher prized alternatives; e.g. di-2......-ethylhexyl adipate or DEHA [103-23-1], also known as Adimoll® or di-octyl adipate, DOA, see Fig. 1. A widely used plasticizer in food (cling) films is DEHA, often in combination with polymers, epoxidized soya-bean oil, etcetera. DEHA also occurs in children toys. We have previously shown that the presence...... of phthalate esters in PVC can be rapidly analyzed by Fourier transform (FT-) Raman spectroscopy excited with a 1064 nm laser. Here in this project we report a similar study. The aim was to find out whether FT-Raman spectroscopy can be used to determine the presence of adipate esters (AEs) as plasticizers...

  12. Vapor-liquid equilibrium for the system ethyl alcohol + ester; Equilibrio liquido-vapor para o sistema alcool etilico+ester

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Humberto Neves Maia de; Nascimento, Yuri Corsino do; Chiavone-Filho, Osvaldo [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2004-07-01

    This work consists of the experimental determination of a series of vapor-liquid equilibrium (VLE) data, for mixtures of ethyl alcohol + ester (ethyl acetate), prepared synthetically, that may be present in the production of biodiesel. The separation of the ethyl alcohol from esters by distillation is an important stage of this process, and therefore it demands accurate data for an appropriate modelling, and later optimization via simulators. FISCHER'S ebulliometer, with digital control (Model 602), was used for measurement of VLE data for the system ethyl alcohol + ester. It consists of a recirculation cell of the both vapor and liquid phases, providing complete data, i.e., pressure, temperature and compositions of the liquid and vapor phases that were obtained by gaseous chromatography (PTxy). This apparatus is coupled to a thermostatic bath with cooling (TE-184 TECNAL) that aims to condense the coming steams of the ebullition in order to return to the mixture camera. The VLE data obtained experimentally were submitted to the test of thermodynamic consistence of the deviations, where the equation of Gibbs-Duhem is used, through the model UNIQUAC. The parameters obtained from the experimental data can be applied in the simulators of processes with the purpose of optimizing the separation of the ethyl alcohol of Ester. (author)

  13. Variability of some diterpene esters in coffee beverages as influenced by brewing procedures.

    Science.gov (United States)

    Moeenfard, Marzieh; Erny, Guillaume L; Alves, Arminda

    2016-11-01

    Several coffee brews, including classical and commercial beverages, were analyzed for their diterpene esters content (cafestol and kahweol linoleate, oleate, palmitate and stearate) by high performance liquid chromatography with diode array detector (HPLC-DAD) combined with spectral deconvolution. Due to the coelution of cafestol and kahweol esters at 225 nm, HPLC-DAD did not give accurate quantification of cafestol esters. Accordingly, spectral deconvolution was used to deconvolve the co-migrating profiles. Total cafestol and kahweol esters content of classical coffee brews ranged from 5-232 to 2-1016 mg/L, respectively. Commercial blends contained 1-54 mg/L of total cafestol esters and 2-403 mg/L of total kahweol esters. Boiled coffee had the highest diterpene esters content, while filtered and instant brews showed the lowest concentrations. However, individual diterpene esters content was not affected by brewing procedure as in terms of kahweol esters, kahweol palmitate was the main compound in all samples, followed by kahweol linoleate, oleate and stearate. Higher amounts of cafestol palmitate and stearate were also observed compared to cafestol linoleate and cafestol oleate. The ratio of diterpene esters esterified with unsaturated fatty acids to total diterpene esters was considered as measure of their unsaturation in analyzed samples which varied from 47 to 52%. Providing new information regarding the diterpene esters content and their distribution in coffee brews will allow a better use of coffee as a functional beverage.

  14. Celorbicol, isocelorbicol, and their esters: new sesquiterpenoids from Celastrus orbiculatus

    Energy Technology Data Exchange (ETDEWEB)

    Smith, C.R. Jr. (Dept. of Agriculture, Peoria, IL); Miller, R.W.; Weisleder, D.; Rohwedder, W.K.; Eickman, N.; Clardy, J.

    1976-10-01

    Esters of two new sesquiterpenoid polyalcohols - celorbicol and isocelorbicol - have been isolated from Celastrus orbiculatus. Structures of the parent alcohols have been established by x-ray crystallography, and those of the derived esters have been assigned by NMR spectroscopy. These compounds are structurally related to other polyesters and ester alkaloids from the Celastraceae, all of which are based on the dihydroagarofuran ring system.

  15. ESR study of electron reactions with esters and triglycerides

    International Nuclear Information System (INIS)

    Sevilla, M.D.; Morehouse, K.M.; Swarts, S.

    1981-01-01

    Reactions which occurred after electron attachment at 77K to a number of small carboxylic acid esters and triglycerides in an aqueous glass are reported. Most ester anions are found to decay on warming to form alkyl radicals by β scission: RC(O - )OR' → RCO 2 - + R'.. The alkyl radical (R'.) produced by annealing is found to abstract hydrogen from the parent ester at an α-carbon site, R'.+ R''CH 2 CO 2 R' → R''CHCO 2 R', or in the case of ethyl formate from the formate hydrogen, CH 3 CH 2 .+ HCO 2 C 2 H 5 → C 2 H 6 +.CO 2 C 2 H 5 . Results found for the methyl formate anion suggest hydrogen abstraction by the anion itself may compete with alkyl radical formation. The anion of the triglyceride triacetin is found to undergo an analogous mechanism to the ester anions producing the propane diol diester radical, .CH 2 CH(Ac)CH 2 (Ac), Ac = acetate. This species subsequently abstracts hydrogen from the parent compound to produce the α-carbon radical, .CH 2 CO 2 R. Results found after annealing the tripropionin radical anion give evidence for abstraction from the α carbon in the propionate side groups producing CH 3 CHCO 2 R. Studies of a γ-irradiated ester (ethyl myristate) and two triglycerides (tripalmitin and tristearin) yield results which suggest that the mechanism of ester anion decay found in aqueous glasses applies to γ-irradiated neat long-chain esters and triglycerides. Results found in this work are compared to the results of product analysis

  16. Two-generation reproductive toxicity study of plant stanol esters in rats

    NARCIS (Netherlands)

    Whittaker, M.H.; Frankos, V.H.; Wolterbeek, A.P.M.; Waalkens-Berendsen, D.H.

    1999-01-01

    Plant stanol esters are intended for use as an ingredient in food to reduce the absorption of cholesterol from the gastrointestinal tract. Consumption of plant stanol esters has a demonstrated diet-derived public health benefit, as shown by numerous clinical studies. Plant stanol esters are

  17. Performance of the mineral blended ester oil-based drilling fluid systems

    Energy Technology Data Exchange (ETDEWEB)

    Ismail, A.R.; Kamis, A.; Foo, K.S. [University Teknologi (Malaysia)

    2001-06-01

    A study was conducted in which the properties of ester oil-based drilling fluid systems were examined using a blended mixture of ester and synthetic mineral oil. Biodegradable invert emulsion ester-based fluids are preferred over mineral oil-based drilling fluids for environmental reasons, but they tend to cause alkaline hydrolysis resulting in solidification of the drilling fluid systems. The drilling fluid examined here consisted of Malaysian palm oil ester derivatives (methyl laureate ester or isopropyl laureate ester) blended with commercially available synthetic mineral oil. This mineral oil was added to reduce the problem of alkaline hydrolysis. This mixture, however, was found to be unstable and could not solve the problem at high temperature. The isopropyl laureate and mineral oil blended system was more stable towards the hydrolysis process up to 250 degrees F. In order to enhance the performance of an invert emulsion drilling fluid system, it was recommended that brine water content of the fluid system be lowered. 3 refs., 2 figs.

  18. Valyl benzyl ester chloride

    Directory of Open Access Journals (Sweden)

    Grzegorz Dutkiewicz

    2010-02-01

    Full Text Available In the title compound (systematic name: 1-benzyloxy-3-methyl-1-oxobutan-2-aminium chloride, C12H18NO2+·Cl−, the ester group is approximately planar, with a maximum deviation of 0.040 (2 Å from the least-squares plane, and makes a dihedral angle of 28.92 (16° with the phenyl ring. The crystal structure is organized by N—H...Cl hydrogen bonds which join the two components into a chain along the b axis. Pairs of chains arranged antiparallel are interconnected by further N—H...Cl hydrogen bonds, forming eight-membered rings. Similar packing modes have been observed in a number of amino acid ester halides with a short unit-cell parameter of ca 5.5 Å along the direction in which the chains run.

  19. Determination of Phthalate Esters in the Aquatic Environment ...

    African Journals Online (AJOL)

    The use of solid phase extraction and capillary GLC provides the basis for selective determination of phthalate ester plasticizers in rivers and marine water samples. Of the several solvent ratios (methanol in dichloromethane) that were tried for selective elution of phthalate esters from the C18 solid phase glass catridge, the ...

  20. The human receptor for urokinase plasminogen activator. NH2-terminal amino acid sequence and glycosylation variants

    DEFF Research Database (Denmark)

    Behrendt, N; Rønne, E; Ploug, M

    1990-01-01

    -PA. The purified protein shows a single 55-60 kDa band after sodium dodecyl sulfate-polyacrylamide gel electrophoresis and silver staining. It is a heavily glycosylated protein, the deglycosylated polypeptide chain comprising only 35 kDa. The glycosylated protein contains N-acetyl-D-glucosamine and sialic acid......, but no N-acetyl-D-galactosamine. Glycosylation is responsible for substantial heterogeneity in the receptor on phorbol ester-stimulated U937 cells, and also for molecular weight variations among various cell lines. The amino acid composition and the NH2-terminal amino acid sequence are reported...

  1. ANALYSIS OF ADIPATE ESTER CONTENTS IN POLY(VINYL CHLORIDE) PLASTICS

    DEFF Research Database (Denmark)

    Berg, Rolf W.; Otero, Amalia Dopazo

    2006-01-01

    Fourier transform (FT-) Raman spectroscopy excited with a 1064 nm laser can be used to determine the content of plasticizers in commercial flexible poly vinyl chloride (PVC) products. Our previous study [T. Nørbygaard, R.W. Berg, Analysis of phthalate ester content in PVC plastics by means of FT......-Raman Spectroscopy, Appl. Spectrosc. 58 (4) (2004) 410–413]—on detection of the presence of phthalate esters in PVC by FT-Raman spectroscopy — is here extended to the similar case of adipate esters (AEs) in samples of soft poly vinyl chloride plastics. Spectra of a range of adipate ester plasticizers (11 AEs......) in pure form are reported. We studied if qualitative and quantitative determination of the adipate ester content would be possible based on the use of proper reference samples. It was found that AEs as a group cannot be definitively identified by their characteristic Raman bands because other aliphatic...

  2. Lipase-Catalyzed Synthesis of Sugar Esters in Honey and Agave Syrup

    Directory of Open Access Journals (Sweden)

    Sascha Siebenhaller

    2018-02-01

    Full Text Available Honey and agave syrup are high quality natural products and consist of more than 80% sugars. They are used as sweeteners, and are ingredients of cosmetics or medical ointments. Furthermore, both have low water content, are often liquid at room temperature and resemble some known sugar-based deep eutectic solvents (DES. Since it has been shown that it is possible to synthesize sugar esters in these DESs, in the current work honey or, as vegan alternative, agave syrup are used simultaneously as solvent and substrate for the enzymatic sugar ester production. For this purpose, important characteristics of the herein used honey and agave syrup were determined and compared with other available types. Subsequently, an enzymatic transesterification of four fatty acid vinyl esters was accomplished in ordinary honey and agave syrup. Notwithstanding of the high water content for transesterification reactions of the solvent, the successful sugar ester formation was proved by thin-layer chromatography (TLC and compared to a sugar ester which was synthesized in a conventional DES. For a clear verification of the sugar esters, mass determinations by ESI-Q-ToF experiments and a NMR analysis were done. These environmentally friendly produced sugar esters have the potential to be used in cosmetics or pharmaceuticals, or to enhance their effectiveness.

  3. Lipase-Catalyzed Synthesis of Sugar Esters in Honey and Agave Syrup

    Science.gov (United States)

    Siebenhaller, Sascha; Gentes, Julian; Infantes, Alba; Muhle-Goll, Claudia; Kirschhöfer, Frank; Brenner-Weiß, Gerald; Ochsenreither, Katrin; Syldatk, Christoph

    2018-02-01

    Honey and agave syrup are high quality natural products and consist of more than 80% sugars. They are used as sweeteners, and are ingredients of cosmetics or medical ointments. Furthermore, both have low water content, are often liquid at room temperature and resemble some known sugar-based deep eutectic solvents. Since it has been shown that it is possible to synthesize sugar esters in these deep eutectic solvents, in the current work honey or, as vegan alternative, agave syrup are used simultaneously as solvent and substrate for the enzymatic sugar ester production. For this purpose, important characteristics of the herein used honey and agave syrup were determined and compared with other available types. Subsequently, an enzymatic transesterification of four fatty acid vinyl esters was accomplished in ordinary honey and agave syrup. Notwithstanding of the high water content for transesterification reactions of the solvent, the successful sugar ester formation was proved by thin-layer chromatography and compared to a sugar ester which was synthesized in a conventional deep eutectic solvent. For a clear verification of the sugar esters, mass determinations by ESI-Q-ToF experiments and a NMR analysis were done. These environmentally friendly produced sugar esters have the potential to be used in cosmetics or pharmaceuticals, or to enhance their effectiveness.

  4. Isolation and identification of an ester from a crude oil

    Science.gov (United States)

    Phillips, H.F.; Breger, I.A.

    1958-01-01

    A dioctylphthalate has been isolated from a crude oil by means of adsorption column chromatography. The ester was identified by means of elemental analysis, refractive index, and its infra-red absorption spectrum. Saponification of the isolate and examination of the resultant alcohol by means of infrared absorption spectra led to the conclusion that the ester is a branched chain dioctylphthalate. This is the first reported occurrence of an ester in crude petroleum. ?? 1958.

  5. Mutagenic activity of phthalate esters in bacterial liquid suspension assays.

    OpenAIRE

    Seed, J L

    1982-01-01

    The mutagenic activities of several phthalate esters have been evaluated in an 8-azaguanine resistance assay in Salmonella typhimurium. Three phthalate esters were found to be mutagenic: dimethyl phthalate, diethyl phthalate and di-n-butyl phthalate. A number of other phthalate esters were not found to be mutagenic, including di(2-ethylhexyl) phthalate, di-n-octyl phthalate, diallyl phthalate, diisobutyl phthalate and diisodecyl phthalate. A metabolite of di(2-ethylhexyl) phthalate, 2-ethylhe...

  6. Natural Organochlorines as Precursors of 3-Monochloropropanediol Esters in Vegetable Oils.

    Science.gov (United States)

    Tiong, Soon Huat; Saparin, Norliza; Teh, Huey Fang; Ng, Theresa Lee Mei; Md Zain, Mohd Zairey Bin; Neoh, Bee Keat; Md Noor, Ahmadilfitri; Tan, Chin Ping; Lai, Oi Ming; Appleton, David Ross

    2018-01-31

    During high-temperature refining of vegetable oils, 3-monochloropropanediol (3-MCPD) esters, possible carcinogens, are formed from acylglycerol in the presence of a chlorine source. To investigate organochlorine compounds in vegetable oils as possible precursors for 3-MCPD esters, we tested crude palm, soybean, rapeseed, sunflower, corn, coconut, and olive oils for the presence of organochlorine compounds. Having found them in all vegetable oils tested, we focused subsequent study on oil palm products. Analysis of the chlorine isotope mass pattern exhibited in high-resolution mass spectrometry enabled organochlorine compound identification in crude palm oils as constituents of wax esters, fatty acid, diacylglycerols, and sphingolipids, which are produced endogenously in oil palm mesocarp throughout ripening. Analysis of thermal decomposition and changes during refining suggested that these naturally present organochlorine compounds in palm oils and perhaps in other vegetable oils are precursors of 3-MCPD esters. Enrichment and dose-response showed a linear relationship to 3-MCPD ester formation and indicated that the sphingolipid-based organochlorine compounds are the most active precursors of 3-MCPD esters.

  7. SYNTHESIS OF FATTY ACID ETHYL ESTER FROM CHICKEN FAT ...

    African Journals Online (AJOL)

    eobe

    synthesis of fatty acid ethyl ester from chicken fat waste using ZnO/SiO fatty acid ethyl ester ... obtained in the range of 56−88%and a second order quadratic polynomial regression model that established the ... Transesterification is a chemical.

  8. Influence of ester-modified lipids on bilayer structure.

    Science.gov (United States)

    Villanueva, Diana Y; Lim, Joseph B; Klauda, Jeffery B

    2013-11-19

    Lipid membranes function as barriers for cells to prevent unwanted chemicals from entering the cell and wanted chemicals from leaving. Because of their hydrophobic interior, membranes do not allow water to penetrate beyond the headgroup region. We performed molecular simulations to examine the effects of ester-modified lipids, which contain ester groups along their hydrocarbon chains, on bilayer structure. We chose two lipids from those presented in Menger et al. [J. Am. Chem. Soc. 2006, 128, 14034] with ester groups in (1) the upper half of the lipid chain (MEPC) and (2) the middle and end of the lipid chain (MGPC). MGPC (30%)/POPC bilayers formed stable water pores of diameter 5-7 Å, but MGPC (22%)/POPC and MEPC (30%)/POPC bilayers did not form these defects. These pores were similar to those formed during electroporation; i.e., the head groups lined the pore and allowed water and ions to transport across the bilayer. However, we found that lateral organization of the MGPC lipids into clusters, instead of an electric field or charge disparity as in electroporation, was essential for pore formation. On the basis of this, we propose an overall mechanism for pore formation. The similarities between the ester-modified lipids and byproducts of lipid peroxidation with multiple hydrophilic groups in the middle of the chain suggest that free radical reactions with unsaturated lipids and sterols result in fundamental changes that may be similar to what is seen in bilayers with ester-modified lipids.

  9. One-pot reaction for the preparation of biofunctionalized self-assembled monolayers on gold surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Raigoza, Annette F.; Fies, Whitney; Lim, Amber; Onyirioha, Kristeen; Webb, Lauren J., E-mail: lwebb@cm.utexas.edu

    2017-02-01

    Highlights: • One-pot synthesis of α-helical-terminated self-assembled monolayers on Au(111). • Synthesis of high density, structured, and covalently bound α-helices on Au(111). • Characterization by surface-averaged and single molecule techniques. • Peptide-terminated surfaces for fabrication of biomaterials and sensors. - Abstract: The Huisgen cycloaddition reaction (“click” chemistry) has been used extensively to functionalize surfaces with macromolecules in a straightforward manner. We have previously developed a procedure using the copper(I)-catalyzed click reaction to tether synthetic α-helical peptides carrying two alkyne groups to a well-ordered azide-terminated alkanethiol self-assembled monolayer (SAM) on a Au(111) surface. While convenient, click-based strategies potentially pose significant problems from reagents, solvents, and reaction temperatures that may irreversibly damage some molecules or substrates. Tuning click chemistry conditions would allow individual optimization of reaction conditions for a wide variety of biomolecules and substrate materials. Here, we explore the utility of simultaneous SAM formation and peptide-attachment chemistry in a one-pot reaction. We demonstrate that a formerly multistep reaction can be successfully carried out concurrently by mixing azide-terminated alkanethiols, CuCl, and a propargylglycine-containing peptide over a bare gold surface in ethanol and reacting at 70 °C. X-ray photoelectron spectroscopy (XPS), surface infrared spectroscopy, surface circular dichroic (CD) spectroscopy, and scanning tunneling microscopy (STM) were used to determine that this one-pot reaction strategy resulted in a high density of surface-bound α-helices without aggregation. This work demonstrates the simplicity and versatility of a SAM-plus-click chemistry strategy for functionalizing Au surfaces with structured biomolecules.

  10. Ester Tuiksoo võitleb viina puhtuse eest / Ester Tuiksoo ; interv. Silja Lättemäe

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2006-01-01

    Põllumajandusminister Ester Tuiksoo lubab Euroopa Liidu piiritusjookide määruse eelnõu arutusel kaitsta seisukohta, et viinaks tuleb pidada üksnes teraviljast või kartulist valmistatud piiritusjooki

  11. N-[11C]methylpiperidine esters as acetylcholinesterase substrates: an in vivo structure-reactivity study

    International Nuclear Information System (INIS)

    Kilbourn, Michael R.; Nguyen, Thinh B.; Snyder, Scott E.; Sherman, Phillip

    1998-01-01

    A series of simple esters incorporating the N-[ 11 C]methylpiperidine structure were examined as in vivo substrates for acetylcholinesterase in mouse brain. 4-N-[ 11 C]Methylpiperidinyl esters, including the acetate, propionate and isobutyrate esters, are good in vivo substrates for mammalian cholinesterases. Introduction of a methyl group at the 4-position of the 4-piperidinol esters, to form the ester of a teritary alcohol, effectively blocks enzymatic action. Methylation of 4- N-[ 11 C]methylpiperidinyl propionate at the 3-position gives a derivative with increased in vivo reactivity toward acetylcholinesterase. Esters of piperidinecarboxylic acids (nipecotic, isonipecotic and pipecolinic acid ethyl esters) are not hydrolyzed by acetylcholinesterase in vivo, nor do they act as in vivo inhibitors of the enzyme. This study has identified simple methods to both increase and decrease the in vivo reactivity of piperidinyl esters toward acetylcholinesterase

  12. Distribution of phthalate esters in underground water from power ...

    African Journals Online (AJOL)

    This study investigates the distribution of phthalateacid esters (PAEs) in groundwater from some power stations in Delta State. Groundwater samples were collected from eight power transmission and distribution stations. Concentrations (μg/L) of six phthalate acid esters compounds in the groundwater ranged from ...

  13. Synthesis of thermoplastic poly(ester-olefin elastomers

    Directory of Open Access Journals (Sweden)

    Tanasijević Branka

    2004-01-01

    Full Text Available A series of thermoplastic poly(ester-olefin elastomers, based on poly(ethylene-stat-butylene, HO-PEB-OH, as the soft segment and poly (butylene terephthalate, PBT, as the hard segment, were synthesized by a catalyzed transesterification reaction in solution. The incorporation of soft hydrogenated poly(butadiene segments into the copolyester backbone was accomplished by the polycondensation of α, ω-dihydroxyl telechelic HO-PEB-OH, (PEB Mn = 3092 g/mol with 1,4-butanediol (BD and dimethyl terephthalate (DMT in the presence of a 50 wt-% high boiling solvent i.e., 1,2,4-trichlorobenzene. The molar ratio of the starting comonomers was selected to result in a constant hard to soft weight ratio of 60:40. The synthesis was optimized in terms of both the concentration of catalyst, tetra-n-butyl-titanate (Ti(OBu4, and stabilizer, N,N'-diphenyl-p-phenylenediamine (DPPD, as well as the reaction time. It was found that the optimal catalyst concentration (Ti(OBu4 for the synthesis of these thermoplastic elastomers was 1.0 mmol/mol ester and the optimal DPPD concentration was 1.0 wt-%. The extent of the reaction was followed by measuring the inherent viscosity of the reaction mixture. The effectiveness of the incorporation of the soft segments into the copolymer chains was proved by Soxhlet extraction with chloroform. The molecular structures, composition and the size of the synthesized poly(ester-butylenes were verified by 1H NMR spectroscopy, viscometry of dilute solutions and the complex dynamic melt viscosity. The thermal properties of poly(ester-olefins were investigated by differential scanning calorimetry (DSC. The degree of crystallinity was also determined by DSC. The thermal and thermo-oxidative stability were investigated by thermogravimetric analysis (TGA. The rheological properties of poly(ester-olefins were investigated by dynamic mechanical spectroscopy in the melt and solid state.

  14. Potential Grape-Derived Contributions to Volatile Ester Concentrations in Wine

    OpenAIRE

    Boss, Paul; Pearce, Anthony; Zhao, Yanjia; Nicholson, Emily; Dennis, Eric; Jeffery, David

    2015-01-01

    Grape composition affects wine flavour and aroma not only through varietal compounds, but also by influencing the production of volatile compounds by yeast. C9 and C12 compounds that potentially influence ethyl ester synthesis during fermentation were studied using a model grape juice medium. It was shown that the addition of free fatty acids, their methyl esters or acyl-carnitine and acyl-amino acid conjugates can increase ethyl ester production in fermentations. The stimulation of ethyl est...

  15. Ester oxidation on an aluminum surface using chemiluminescence

    Science.gov (United States)

    Jones, William R., Jr.; Meador, Michael A.; Morales, Wilfredo

    1986-01-01

    The oxidation characteristics of a pure ester (trimethyolpropane triheptanoate) were studied by using a chemiluminescence technique. Tests were run in a thin film microoxidation apparatus with an aluminum alloy catalyst. Conditions included a pure oxygen atmosphere and a temperature range of 176 to 206 C. Results indicated that oxidation of the ester (containing .001 M diphenylanthracene as an intensifier) was accompanied by emission of light. The maximum intensity of light emission was a function of the amount of ester, the concentration of intensifier, and the test temperature. The induction period, or the time to reach one-half of maximum intensity was inversely proportional to test temperature. Decreases in light emission at the later stages of a test were caused by depletion of the intensifier.

  16. A Lactobacillus plantarum Esterase Active on a Broad Range of Phenolic Esters

    Science.gov (United States)

    Esteban-Torres, María; Landete, José María; Reverón, Inés; Santamaría, Laura; de las Rivas, Blanca

    2015-01-01

    Lactobacillus plantarum is the lactic acid bacterial species most frequently found in the fermentation of food products of plant origin on which phenolic compounds are abundant. L. plantarum strains showed great flexibility in their ability to adapt to different environments and growth substrates. Of 28 L. plantarum strains analyzed, only cultures from 7 strains were able to hydrolyze hydroxycinnamic esters, such as methyl ferulate or methyl caffeate. As revealed by PCR, only these seven strains possessed the est_1092 gene. When the est_1092 gene was introduced into L. plantarum WCFS1 or L. lactis MG1363, their cultures acquired the ability to degrade hydroxycinnamic esters. These results support the suggestion that Est_1092 is the enzyme responsible for the degradation of hydroxycinnamic esters on the L. plantarum strains analyzed. The Est_1092 protein was recombinantly produced and biochemically characterized. Surprisingly, Est_1092 was able to hydrolyze not only hydroxycinnamic esters, since all the phenolic esters assayed were hydrolyzed. Quantitative PCR experiments revealed that the expression of est_1092 was induced in the presence of methyl ferulate, an hydroxycinnamic ester, but was inhibited on methyl gallate, an hydroxybenzoic ester. As Est_1092 is an enzyme active on a broad range of phenolic esters, simultaneously possessing feruloyl esterase and tannase activities, its presence on some L. plantarum strains provides them with additional advantages to survive and grow on plant environments. PMID:25746986

  17. Preferential enrichment of large-sized very low density lipoprotein populations with transferred cholesteryl esters

    International Nuclear Information System (INIS)

    Eisenberg, S.

    1985-01-01

    The effect of lipid transfer proteins on the exchange and transfer of cholesteryl esters from rat plasma HDL2 to human very low (VLDL) and low density (LDL) lipoprotein populations was studied. The use of a combination of radiochemical and chemical methods allowed separate assessment of [ 3 H]cholesteryl ester exchange and of cholesteryl ester transfer. VLDL-I was the preferred acceptor for transferred cholesteryl esters, followed by VLDL-II and VLDL-III. LDL did not acquire cholesteryl esters. The contribution of exchange of [ 3 H]cholesteryl esters to total transfer was highest for LDL and decreased in reverse order along the VLDL density range. Inactivation of lecithin: cholesterol acyltransferase (LCAT) and heating the HDL2 for 60 min at 56 degrees C accelerated transfer and exchange of [ 3 H]cholesteryl esters. Addition of lipid transfer proteins increased cholesterol esterification in all systems. The data demonstrate that large-sized, triglyceride-rich VLDL particles are preferred acceptors for transferred cholesteryl esters. It is suggested that enrichment of very low density lipoproteins with cholesteryl esters reflects the triglyceride content of the particles

  18. Power distribution transformers using natural ester fluids as dielectric and coolant

    Directory of Open Access Journals (Sweden)

    Jorge Iván Silva-Ortega

    2016-12-01

    Full Text Available Researches related to the use of Natural Ester Fluids as a refrigerant of power transformers have been developed in other countries with successful results. In Colombia there is no a procedure to control the use of these esters in electrical apparatus, so the current implementations are regulated by NTC 1465 standards for mineral esters. This new proposal involves the composition and the most relevant properties (the ignition resistance, impact on the lifetime of the insulating papers and the impact on the environment, which makes the application of natural esters fluids advantageous not only to preserve the environment but also to get a better performance of power transformers.

  19. Unsaturated Fatty Acid Esters Metathesis Catalyzed by Silica Supported WMe5

    KAUST Repository

    Riache, Nassima

    2015-11-14

    Metathesis of unsaturated fatty acid esters (FAEs) by silica supported multifunctional W-based catalyst is disclosed. This transformation represents a novel route towards unsaturated di-esters. Especially, the self-metathesis of ethyl undecylenate results almost exclusively on the homo-coupling product whereas with such catalyst, 1-decene gives ISOMET (isomerization and metathesis olefin) products. The olefin metathesis in the presence of esters is very selective without any secondary cross-metathesis products demonstrating that a high selective olefin metathesis could operate at 150 °C. Additionally, a cross-metathesis of unsaturated FAEs and α-olefins allowed the synthesis of the corresponding ester with longer hydrocarbon skeleton without isomerisation.

  20. Critical aggregates concentration of fatty esters present in biodiesel determined by turbidity and fluorescence.

    Science.gov (United States)

    Froehner, Sandro; Sánez, Juan; Dombroski, Luiz Fernando; Gracioto, Maria Paula

    2017-09-01

    Biodiesel for combustible engine is available as mixture of fossil diesel and fatty esters obtained by transesterification of vegetable oils. The use of biodiesel reduces the amount of SO x , mainly. However, it was already observed that biodiesel has a different behavior in environment in cases of accidental spill and groundwater contamination. It was noticed that the biodegradation of hydrocarbons (cyclic and aliphatic) in the presence of biodiesel are speeded, although the mechanism is still unclear. Considering the chemical structure of fatty esters, it was investigated the formation of aggregates in water solution by fatty esters present in commercial biodiesel. In Brazil, biodiesel is composed by 95% of fossil diesel and 5% of fatty esters mixture. In this work, fatty esters were treated as neutral surfactant, i.e., it was treated as a molecule with polar and non-polar part. Turbidity and fluorescence were used to determine the critical aggregates concentration (CAC). Water solutions containing fatty esters were examined exploiting changes in turbidity and fluorescence intensity of pyrene. Abrupt changes were attributed to aggregates formation, following the same behavior of traditional amphiphilic compounds. It was determined the CAC for ethyl palmitate, ethyl stearate, ethyl oleate, and ethyl linoleate. The values of CAC for fatty esters varied from 1.91 to 4.27 μmol/L, while CAC for the mixture of esters (biodiesel) was 2.01 for methyl esters and 1.19 for ethyl esters, both prepared using soybean oil. The aggregates formation was also determined by fluorescence measurements considering the changes in intensity of peaks I and III of pyrene. Pyrene senses the changes in environment polarity. The values found of CAC by fluorescence for individual ethyl esters varied from 1.85 to 3.21 μmol/L, while mixtures of ethyl esters was 2.23 and 2.07 μmol/L for mixture of methyl esters. The results clearly showed that fatty esters form aggregates and might be

  1. Half esters and coating compositions comprising reactions products of half esters and polyepoxides

    NARCIS (Netherlands)

    Blaauw, R.; Mulder, W.J.; Koelewijn, R.; Boswinkel, G.

    2006-01-01

    The present invention relates to half esters based on dicarboxylic acid derivatives and dimer fatty diols, wherein the dimer fatty dio ls are based on dimerised and/or trimerised and/or oligomerised unsaturated fatty acids. The present invention further relates to resin compositions based on the

  2. Catalytic Ester and Amide to Amine Interconversion: Nickel-Catalyzed Decarbonylative Amination of Esters and Amides by C−O and C−C Bond Activation

    KAUST Repository

    Yue, Huifeng

    2017-03-15

    An efficient nickel-catalyzed decarbonylative amination reaction of aryl and heteroaryl esters has been achieved for the first time. The new amination protocol allows the direct interconversion of esters and amides into the corresponding amines and represents a good alternative to classical rearrangements as well as cross coupling reactions.

  3. Catalytic Ester and Amide to Amine Interconversion: Nickel-Catalyzed Decarbonylative Amination of Esters and Amides by C−O and C−C Bond Activation

    KAUST Repository

    Yue, Huifeng; Guo, Lin; Liao, Hsuan-Hung; Cai, Yunfei; Zhu, Chen; Rueping, Magnus

    2017-01-01

    An efficient nickel-catalyzed decarbonylative amination reaction of aryl and heteroaryl esters has been achieved for the first time. The new amination protocol allows the direct interconversion of esters and amides into the corresponding amines and represents a good alternative to classical rearrangements as well as cross coupling reactions.

  4. 21 CFR 573.660 - Methyl glucoside-coconut oil ester.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 6 2010-04-01 2010-04-01 false Methyl glucoside-coconut oil ester. 573.660 Section 573.660 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES... ANIMALS Food Additive Listing § 573.660 Methyl glucoside-coconut oil ester. Methyl glucoside-coconut oil...

  5. A Lactobacillus plantarum esterase active on a broad range of phenolic esters.

    Science.gov (United States)

    Esteban-Torres, María; Landete, José María; Reverón, Inés; Santamaría, Laura; de las Rivas, Blanca; Muñoz, Rosario

    2015-05-01

    Lactobacillus plantarum is the lactic acid bacterial species most frequently found in the fermentation of food products of plant origin on which phenolic compounds are abundant. L. plantarum strains showed great flexibility in their ability to adapt to different environments and growth substrates. Of 28 L. plantarum strains analyzed, only cultures from 7 strains were able to hydrolyze hydroxycinnamic esters, such as methyl ferulate or methyl caffeate. As revealed by PCR, only these seven strains possessed the est_1092 gene. When the est_1092 gene was introduced into L. plantarum WCFS1 or L. lactis MG1363, their cultures acquired the ability to degrade hydroxycinnamic esters. These results support the suggestion that Est_1092 is the enzyme responsible for the degradation of hydroxycinnamic esters on the L. plantarum strains analyzed. The Est_1092 protein was recombinantly produced and biochemically characterized. Surprisingly, Est_1092 was able to hydrolyze not only hydroxycinnamic esters, since all the phenolic esters assayed were hydrolyzed. Quantitative PCR experiments revealed that the expression of est_1092 was induced in the presence of methyl ferulate, an hydroxycinnamic ester, but was inhibited on methyl gallate, an hydroxybenzoic ester. As Est_1092 is an enzyme active on a broad range of phenolic esters, simultaneously possessing feruloyl esterase and tannase activities, its presence on some L. plantarum strains provides them with additional advantages to survive and grow on plant environments. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  6. KARAKTERISTIK EMULSI SANTAN DAN MINYAK KEDELAI YANG DITAMBAH GUM ARAB DAN SUKROSA ESTER [Emulsion Characteristics of Coconut Milk and Soybean Oil Added with Gum Arabic and Sucrose Ester

    Directory of Open Access Journals (Sweden)

    Laksmi Hartayanie

    2015-07-01

    Full Text Available High saturated fatty acid content in coconut milk can be reduced by adding unsaturated fat. Pretreatment such as pasteurisation, homogenization or stabilizer and emulsifier addition are essential to prevent emulsion deterioration that could happen in few hours. This study aimed to determine the most appropriate combination of gum arabic and sucrose ester to produce good emulsion stability based on its physical and chemical characteristics. Furthermore this study also aimed to determine correlation between creaming index and other characteristics of coconut milk emulsion. Emulsion stability of mixed coconut milk in sterile glass bottles was observed for 7 days under 23-24°C. Stabilizer and emulsifier added were gum arabic and sucrose ester in five combinations, i.e. 6% gum arabic, 0.3% sucrose ester, 6% gum arabic + 0.3% sucrose ester, 3% gum arabic + 0.15% sucrose ester and 4.5% gum arabic + 0.225% sucrose ester. The physical characteristics evaluated were creaming index, total color change, viscosity and droplet distribution, while the chemical characteristics observed included pH, TBA value, and protein content. Data were analyzed by One Way Anova at 95% significant level to determine the differences among treatments. Bivariate Pearson Correlation was used in order to determine the interaction among sample characteristics. The data showed that, gum arabic and sucrose ester can maintain the emulsion stability. A combination of 4.5% gum arabic and 0.225% sucrose ester provided the best physicochemical characteristics with the lowest creaming index and decreased viscosit, and uniform droplet distribution.

  7. Determination of 3-Monochloropropane-1,2-diol and 2-Monochloropropane-1,3-diol (MCPD) Esters and Glycidyl Esters by Microwave Extraction in Different Foodstuffs.

    Science.gov (United States)

    Marc, Corinne; Drouard-Pascarel, Valérie; Rétho, Cécile; Janvion, Patrice; Saltron, Frédéric

    2016-06-01

    This paper describes a method for the determination of 3-monochloropropane-1,2-diol and 2-monochloropropane-1,3-diol (MCPD) esters and glycidyl esters in various foodstuffs, which are isolated using microwave extraction. The next step is based on alkaline-catalyzed ester cleavage. The released glycidol is transformed into monobromopropanediol (MBPD). All compounds are derivatized in free diols (MCPD and MBPD) with phenylboronic acid and analyzed by gas chromatography-mass spectrometry (GC-MS). The method was validated for oils with a limit of quantitation (LOQ) of 0.1 mg/kg, for chips and crisps with a LOQ of 0.02 mg/kg, and for infant formula with a LOQ of 0.0025 mg/L. Recoveries of each sample were controlled by standard addition on extracts before derivatization. Quantitation was performed by the addition of isotopically labeled glycidyl and 3-monochloropropane-1,2-diol (3-MCPD) esters.

  8. Synthesis and antimalarial testing of neocryptolepine analogues: addition of ester function in SAR study of 2,11-disubstituted indolo[2,3-b]quinolines.

    Science.gov (United States)

    Lu, Wen-Jie; Wicht, Kathryn J; Wang, Li; Imai, Kento; Mei, Zhen-Wu; Kaiser, Marcel; El Sayed, Ibrahim El Tantawy; Egan, Timothy J; Inokuchi, Tsutomu

    2013-06-01

    This report describes the synthesis, and in vitro and in vivo antimalarial evaluations of certain ester-modified neocryptolepine (5-methyl-5H-indolo[2,3-b]quinoline) derivatives. The modifications were carried out by introducing ester groups at the C2 and/or C9 position on the neocryptolepine core and the terminal amino group of the 3-aminopropylamine substituents at the C11 position with a urea/thiourea unit. The antiplasmodial activities of our derivative agents against two different strains (CQS: NF54, and CQR: K1) and the cytotoxic activity against normal L6 cells were evaluated. The test results showed that the ester modified neocryptolepine derivatives have higher antiplasmodial activities against both strains and a low cytotoxic activity against normal cells. The best results were achieved by compounds 9c and 12b against the NF54 strain with the IC50/SI value as 2.27 nM/361 and 1.81 nM/321, respectively. While against K1 strain, all the tested compounds showed higher activity than the well-known antimalarial drug chloroquine. Furthermore, the compounds were tested for β-haematin inhibition and 12 were found to be more active than chloroquine (IC50 = 18 μM). Structure activity relationship studies exposed an interesting linear correlation between polar surface area of the molecule and β-haematin inhibition for this series. In vivo testing of compounds 7 and 8a against NF54 strain on Plasmodium berghei female mice showed that the introduction of the ester group increased the antiplasmodial activity of the neocryptolepine core substantially. Copyright © 2013 Elsevier Masson SAS. All rights reserved.

  9. Alternative Production of Fatty Acid Methyl Esters from Triglycerides ...

    African Journals Online (AJOL)

    The catalysts activity was tested in thermocatalytic cracking of triglyceride; a direct conversion process for fatty acid methyl esters (biodiesel). The SZ1 not only exhibited higher conversion of triglycerides but higher fatty acid methyl esters (FAMEs) yields of approximately 59% after 3h as compared to SZ2 (32%). In addition ...

  10. Steryl ester synthesis, storage and hydrolysis: A contribution to sterol homeostasis.

    Science.gov (United States)

    Korber, Martina; Klein, Isabella; Daum, Günther

    2017-12-01

    Sterols are essential lipids of all eukaryotic cells, appearing either as free sterols or steryl esters. Besides other regulatory mechanisms, esterification of sterols and hydrolysis of steryl esters serve to buffer both an excess and a lack of free sterols. In this review, the esterification process, the storage of steryl esters and their mobilization will be described. Several model organisms are discussed but the focus was set on mammals and the yeast Saccharomyces cerevisiae. The contribution of imbalanced cholesterol homeostasis to several human diseases, namely Wolman disease, cholesteryl ester storage disease, atherosclerosis and Alzheimer's disease, Niemann-Pick type C and Tangier disease is described. Copyright © 2017 Elsevier B.V. All rights reserved.

  11. Nickel-Catalyzed C–O Bond-Cleaving Alkylation of Esters: Direct Replacement of the Ester Moiety by Functionalized Alkyl Chains

    KAUST Repository

    Liu, Xiangqian; Jia, Jiaqi; Rueping, Magnus

    2017-01-01

    Two efficient protocols for the nickel-catalyzed aryl–alkyl cross-coupling reactions using esters as coupling components have been established. The methods enable the selective oxidative addition of nickel to acyl C–O and aryl C–O bonds and allow the aryl–alkyl cross-coupling via decarbonylative bond cleavage or through cleavage of a C–O bond with high efficiency and good functional group compatibility. The protocols allow the streamlined, unconventional utilization of widespread ester groups and their precursors, carboxylic acids and phenols, in synthetic organic chemistry.

  12. Nickel-Catalyzed C–O Bond-Cleaving Alkylation of Esters: Direct Replacement of the Ester Moiety by Functionalized Alkyl Chains

    KAUST Repository

    Liu, Xiangqian

    2017-06-07

    Two efficient protocols for the nickel-catalyzed aryl–alkyl cross-coupling reactions using esters as coupling components have been established. The methods enable the selective oxidative addition of nickel to acyl C–O and aryl C–O bonds and allow the aryl–alkyl cross-coupling via decarbonylative bond cleavage or through cleavage of a C–O bond with high efficiency and good functional group compatibility. The protocols allow the streamlined, unconventional utilization of widespread ester groups and their precursors, carboxylic acids and phenols, in synthetic organic chemistry.

  13. Complex formation of technetium with the methyl esters of MAG2 and MAG1

    International Nuclear Information System (INIS)

    Noll, B.; Noll, S.; Grosse, B.; Johannsen, B.; Spies, H.

    1993-01-01

    Mercaptoacetylglycine methyl ester (MAG 2 ester) and mercaptoacetyldiglycine methyl ester (MAG 1 ester) were included to investigate complex formation of SH/amide ligands with technetium. The studies are aimed at finding out how blocking the carboxylic groups influences the complexation reaction, with a view to finding an approach to new lipophilic species. (orig./BBR)

  14. Synthesis of chiral N-phosphinyl α-imino esters and their application in asymmetric synthesis of α-amino esters by reduction

    OpenAIRE

    Xiong, Yiwen; Mei, Haibo; Wu, Lingmin; Han, Jianlin; Pan, Yi; Li, Guigen

    2014-01-01

    A variety of chiral N-phosphinyl α-imino esters have been synthesized for the first time from ketoesters and phosphinylamide, which were then reduced by L-selectride to give the corresponding N-phosphinyl-protected α-amino esters. The reduction proceeded very well with excellent chemical yields (88–98%) as well as high diastereoselectivities (96:4 to 99:1). Some of these products could be obtained without column chromatography and recrystallization. The chiral phosphinyl auxiliary could be ea...

  15. Synthesis of [11C]-labelled methyl esters: transesterification of enol esters versus BF3 etherate catalysed esterification - a comparative study

    International Nuclear Information System (INIS)

    Ackermann, U.; Falzon, C.; Issa, W.; Tochon-Danguy, H.J.; Sachinidis, J.I.; Blanc, P.; White, J.; Scott, A.M.

    2005-01-01

    An important issue in Positron Emission Tomography (PET) is the development of labelling techniques to incorporate positron emitting radionuclides into biologically active compounds. When labelling with 11C, the short 20 minutes half-life of the radionuclide significantly limits the number of synthetic protocols available to the radiochemist. C-l synthons such as [HCJ-methyl iodide (1) or methyl triflate (2) are readily available and are frequently used as alkylating agents for the preparation of radiopharmaceuticals. However, the use of these alkylating agents often makes it necessary to introduce protecting groups in order to prevent labelling at unwanted sites on the molecule. Since the removal of protecting groups is a time-consuming process, a more direct synthesis strategy is desirable. This has prompted us to investigate the esterification of carboxylic acids using [1 lC]-mcthanol and BF3 etherate as Lewis acid catalyst. Our results have demonstrated that the reaction conditions necessary to promote the esterification can cleave functional groups such as ethers. We have therefore shifted our attention towards the irreversible transesterification of enol esters using [HCl-methanol and a tin catalyst as an alternative strategy to [HC]-methyl ester formation. We have prepared a series of 5 aromatic ethoxy vinyl esters bearing various functional groups. The transesterification (radiolabelling) was carried out in DMSO at 150 Degrees C for 7 minutes in the presence of [HQMeOH and 1.3-dichlo-rotetrabutyldistannoxane as catalyst. We have found that the transesterification of enol esters is a mild and efficient labelling method for the formation of [HCl-methyl esters. The reaction proceeds smoothly and leaves functional groups intact. It requires only one synthesis step compared to two steps for the conventional method, and gives a radiochemical yields of 25%

  16. New Insights on Degumming and Bleaching Process Parameters on The Formation of 3-Monochloropropane-1,2-Diol Esters and Glycidyl Esters in Refined, Bleached, Deodorized Palm Oil.

    Science.gov (United States)

    Sim, Biow Ing; Muhamad, Halimah; Lai, Oi Ming; Abas, Faridah; Yeoh, Chee Beng; Nehdi, Imededdine Arbi; Khor, Yih Phing; Tan, Chin Ping

    2018-04-01

    This paper examines the interactions of degumming and bleaching processes as well as their influences on the formation of 3-monochloropropane-1,2-diol esters (3-MCPDE) and glycidyl esters in refined, bleached and deodorized palm oil by using D-optimal design. Water degumming effectively reduced the 3-MCPDE content up to 50%. Acid activated bleaching earth had a greater effect on 3-MCPDE reduction compared to natural bleaching earth and acid activated bleaching earth with neutral pH, indicating that performance and adsorption capacities of bleaching earth are the predominant factors in the removal of esters, rather than its acidity profile. The combination of high dosage phosphoric acid during degumming with the use of acid activated bleaching earth eliminated almost all glycidyl esters during refining. Besides, the effects of crude palm oil quality was assessed and it was found that the quality of crude palm oil determines the level of formation of 3-MCPDE and glycidyl esters in palm oil during the high temperature deodorization step of physical refining process. Poor quality crude palm oil has strong impact towards 3-MCPDE and glycidyl esters formation due to the intrinsic components present within. The findings are useful to palm oil refining industry in choosing raw materials as an input during the refining process.

  17. Preparation of esters of gallic acid with higher primary alcohols

    NARCIS (Netherlands)

    Kerk, G.J.M. van der; Verbeek, J.H.; Cleton, J.C.F.

    1951-01-01

    The esters of gallic acid and higher primary alcohols, especially fatty alcohols, have recently gained considerable interest as possible antioxidants for fats. Two independent methods for the preparation of these esters are described. In the first method the hitherto unknown compound galloyl

  18. Baker's yeast: production of D- and L-3-hydroxy esters

    DEFF Research Database (Denmark)

    Dahl, Allan Carsten; Madsen, Jørgen Øgaard

    1998-01-01

    harvested while growing. In contrast, the stereoselectivity was shifted towards L-hydroxy esters when the oxo esters were added slowly to ordinary baker's yeast supplied with gluconolactone as co-substrate. The reduction rate with gluconolactone was increased by active aeration. Ethyl L-(S)-3......Baker's yeast grown under oxygen limited conditions and used in the reduction of 3-oxo esters results in a shift of the stereoselectivity of the yeast towards D-hydroxy esters as compared with ordinary baker's yeast. The highest degree of stereoselectivity was obtained with growing yeast or yeast......-hydroxybutanoate was afforded in >99% ee. Both enantiomers of ethyl 3-hydroxypentanoate, D-(R) in 96% ee and L-(S) in 93% ee, and of ethyl 4-chloro-3-hydroxybutanoate, D-(S) in 98% ee and L-(R) in 94% ee, were obtained. The results demonstrate that the stereoselectivity of baker's yeast can be controlled...

  19. Synthesis of novel naphthoquinone aliphatic amides and esters and their anticancer evaluation.

    Science.gov (United States)

    Kongkathip, Boonsong; Akkarasamiyo, Sunisa; Hasitapan, Komkrit; Sittikul, Pichamon; Boonyalai, Nonlawat; Kongkathip, Ngampong

    2013-02-01

    Fourteen new naphthoquinone aliphatic amides and seventeen naphthoquinone aliphatic esters were synthesized in nine to ten steps from 1-hydroxy-2-naphthoic acid with 9-25% overall yield for the amides, and 16-21% overall yield for the esters. The key step of the amide synthesis is a coupling reaction between amine and various aliphatic acids using 4-(4,6-dimethoxy-1,3,5-triazin-2-yl)-4-methylmorpholinium chloride (DMTMM) as a coupling agent while for the ester synthesis, DCC/DMAP or CDI was used as the coupling reagent between aliphatic acids and naphthoquinone alcohol. Both naphthoquinone amides and esters were evaluated for their anticancer activity against KB cells. It was found that naphthoquinone aliphatic amides showed stronger anticancer activity than those of the esters when the chains are longer than 7-carbon atoms. The optimum chain of amides is expected to be 16-carbon atoms. In addition, naphthoquinone aliphatic esters with α-methyl on the ester moiety possessed much stronger anticancer activity than the straight chains. Decatenation assay revealed that naphthoquinone amide with 16-carbon atoms chain at 15 μM and 20 μM can completely inhibit hTopoIIα activity while at 10 μM the enzyme activity was moderately inhibited. Molecular docking result also showed the same trend as the cytotoxicity and decatenation assay. Copyright © 2012 Elsevier Masson SAS. All rights reserved.

  20. Structural characterization of saturated branched chain fatty acid methyl esters by collisional dissociation of molecular ions generated by electron ionization.

    Science.gov (United States)

    Ran-Ressler, Rinat R; Lawrence, Peter; Brenna, J Thomas

    2012-01-01

    Saturated branched chain fatty acids (BCFA) are present as complex mixtures in numerous biological samples. The traditional method for structure elucidation, electron ionization (EI) mass spectrometry, sometimes does not unambiguously enable assignment of branching in isomeric BCFA. Zirrolli and Murphy (Zirrolli , J. A. , and R. A. Murphy. 1993. Low-energy tandem mass spectrometry of the molecular ion derived from fatty acid methyl esters: a novel method for analysis of branched-chain fatty acids. J. Am. Soc. Mass Spectrom. 4: 223-229.) showed that the molecular ions of four BCFA methyl ester (BCFAME) yield highly characteristic fragments upon collisional dissociation using a triple quadrupole instrument. Here, we confirm and extend these results by analysis using a tabletop 3-D ion trap for activated molecular ion EI-MS/MS to 30 BCFAME. iso-BCFAME produces a prominent ion (30-100% of base peak) for [M-43] (M-C₃H₇), corresponding to the terminal isopropyl moiety in the original iso-BCFAME. Anteiso-FAME yield prominent ions (20-100% of base peak) corresponding to losses on both side of the methyl branch, [M-29] and [M-57], and tend to produce more prominent m/z 115 peaks corresponding to a cyclization product around the ester. Dimethyl and tetramethyl FAME, with branches separated by at least one methylene group, yield fragment on both sides of the sites of methyl branches that are more than 6 C away from the carboxyl carbon. EI-MS/MS yields uniquely specific ions that enable highly confident structural identification and quantification of BCFAME.

  1. Synthesis of chiral N-phosphinyl α-imino esters and their application in asymmetric synthesis of α-amino esters by reduction.

    Science.gov (United States)

    Xiong, Yiwen; Mei, Haibo; Wu, Lingmin; Han, Jianlin; Pan, Yi; Li, Guigen

    2014-01-01

    A variety of chiral N-phosphinyl α-imino esters have been synthesized for the first time from ketoesters and phosphinylamide, which were then reduced by L-selectride to give the corresponding N-phosphinyl-protected α-amino esters. The reduction proceeded very well with excellent chemical yields (88-98%) as well as high diastereoselectivities (96:4 to 99:1). Some of these products could be obtained without column chromatography and recrystallization. The chiral phosphinyl auxiliary could be easily cleaved under acidic conditions.

  2. Sugar ester surfactants: enzymatic synthesis and applications in food industry.

    Science.gov (United States)

    Neta, Nair S; Teixeira, José A; Rodrigues, Lígia R

    2015-01-01

    Sugar esters are non-ionic surfactants that can be synthesized in a single enzymatic reaction step using lipases. The stability and efficiency of lipases under unusual conditions and using non-conventional media can be significantly improved through immobilization and protein engineering. Also, the development of de novo enzymes has seen a significant increase lately under the scope of the new field of synthetic biology. Depending on the esterification degree and the nature of fatty acid and/or sugar, a range of sugar esters can be synthesized. Due to their surface activity and emulsifying capacity, sugar esters are promising for applications in food industry.

  3. Novel Synthesis of Phytosterol Ester from Soybean Sterol and Acetic Anhydride.

    Science.gov (United States)

    Yang, Fuming; Oyeyinka, Samson A; Ma, Ying

    2016-07-01

    Phytosterols are important bioactive compounds which have several health benefits including reduction of serum cholesterol and preventing cardiovascular diseases. The most widely used method in the synthesis of its ester analogous form is the use of catalysts and solvents. These methods have been found to present some safety and health concern. In this paper, an alternative method of synthesizing phytosterol ester from soybean sterol and acetic anhydride was investigated. Process parameters such as mole ratio, temperature and time were optimized. The structure and physicochemical properties of phytosterol acetic ester were analyzed. By the use of gas chromatography, the mole ratio of soybean sterol and acetic anhydride needed for optimum esterification rate of 99.4% was 1:1 at 135 °C for 1.5 h. FTIR spectra confirmed the formation of phytosterol ester with strong absorption peaks at 1732 and 1250 cm(-1) , which corresponds to the stretching vibration of C=O and C-O-C, respectively. These peaks could be attributed to the formation of ester links which resulted from the reaction between the hydroxyl group of soybean sterol and the carbonyl group of acetic anhydride. This paper provides a better alternative to the synthesis of phytosterol ester without catalyst and solvent residues, which may have potential application in the food, health-care food, and pharmaceutical industries. © 2016 Institute of Food Technologists®

  4. Ester-free Thiol-X Resins: New Materials with Enhanced Mechanical Behavior and Solvent Resistance

    OpenAIRE

    Podgórski, Maciej; Becka, Eftalda; Chatani, Shunsuke; Claudino, Mauro; Bowman, Christopher N.

    2015-01-01

    A series of thiol-Michael and radical thiol-ene network polymers were successfully prepared from ester-free as well as ester-containing monomer formulations. Polymerization reaction rates, dynamic mechanical analysis, and solvent resistance experiments were performed and compared between compositions with varied ester loading. The incorporation of ester-free alkyl thiol, vinyl sulfone and allylic monomers significantly improved the mechanical properties when compared with commercial, mercapto...

  5. Encapsulating fatty acid esters of bioactive compounds in starch

    Science.gov (United States)

    Lay Ma, Ursula Vanesa

    Interest in the use of many bioactive compounds in foods is growing in large part because of the apparent health benefits of these molecules. However, many of these compounds can be easily degraded during processing, storage, or their passage through the gastrointestinal tract before reaching the target site. In addition, they can be bitter, acrid, or astringent, which may negatively affect the sensory properties of the product. Encapsulation of these molecules may increase their stability during processing, storage, and in the gastrointestinal tract, while providing controlled release properties. The ability of amylose to form inclusion complexes and spherulites while entrapping certain compounds has been suggested as a potential method for encapsulation of certain molecules. However, complex formation and spherulitic crystallization are greatly affected by the type of inclusion molecules, type of starch, and processing conditions. The objectives of the present investigation were to: (a) study the effect of amylose, amylopectin, and intermediate material on spherulite formation and its microstructure; (b) investigate the formation of amylose and high amylose starch inclusion complexes with ascorbyl palmitate, retinyl palmitate, and phytosterol esters; (c) evaluate the ability of spherulites to form in the presence of fatty acid esters and to entrap ascorbyl palmitate, retinyl palmitate, and phytosterol esters; and (d) evaluate the effect of processing conditions on spherulite formation and fatty acid ester entrapment. Higher ratios of linear to branched molecules resulted in the formation of more and rounder spherulites with higher heat stability. In addition to the presence of branches, it appears that spherulitic crystallization is also affected by other factors, such as degree of branching, chain length, and chain length distribution. Amylose and Hylon VII starch formed inclusion complexes with fatty acid esters of ascorbic acid, retinol, or phytosterols

  6. Unsaturated Fatty Acid Esters Metathesis Catalyzed by Silica Supported WMe5

    KAUST Repository

    Riache, Nassima; Callens, Emmanuel; Talbi, Karima; Basset, Jean-Marie

    2015-01-01

    Metathesis of unsaturated fatty acid esters (FAEs) by silica supported multifunctional W-based catalyst is disclosed. This transformation represents a novel route towards unsaturated di-esters. Especially, the self-metathesis of ethyl undecylenate

  7. Synthesis of oleyl oleate wax esters in Arabidopsis thaliana and Camelina sativa seed oil.

    Science.gov (United States)

    Iven, Tim; Hornung, Ellen; Heilmann, Mareike; Feussner, Ivo

    2016-01-01

    Seed oil composed of wax esters with long-chain monoenoic acyl moieties represents a high-value commodity for industry. Such plant-derived sperm oil-like liquid wax esters are biodegradable and can have excellent properties for lubrication. In addition, wax ester oil may represent a superior substrate for biodiesel production. In this study, we demonstrate that the low-input oil seed crop Camelina sativa can serve as a biotechnological platform for environmentally benign wax ester production. Two biosynthetic steps catalysed by a fatty alcohol-forming acyl-CoA reductase (FAR) and a wax ester synthase (WS) are sufficient to achieve wax ester accumulation from acyl-CoA substrates. To produce plant-derived sperm oil-like liquid wax esters, the WS from Mus musculus (MmWS) or Simmondsia chinensis (ScWS) were expressed in combination with the FAR from Mus musculus (MmFAR1) or Marinobacter aquaeolei (MaFAR) in seeds of Arabidopsis thaliana and Camelina sativa. The three analysed enzyme combinations Oleo3:mCherry:MmFAR1∆c/Oleo3:EYFP:MmWS, Oleo3:mCherry:MmFAR1∆c/ScWS and MaFAR/ScWS showed differences in the wax ester molecular species profiles and overall biosynthetic performance. By expressing MaFAR/ScWS in Arabidopsis or Camelina up to 59% or 21% of the seed oil TAGs were replaced by wax esters, respectively. This combination also yielded wax ester molecular species with highest content of monounsaturated acyl moieties. Expression of the enzyme combinations in the Arabidopsis fae1 fad2 mutant background high in oleic acid resulted in wax ester accumulation enriched in oleyl oleate (18:1/18:1 > 60%), suggesting that similar values may be obtained with a Camelina high oleic acid line. © 2015 Society for Experimental Biology, Association of Applied Biologists and John Wiley & Sons Ltd.

  8. Conformational states of N-acylalanine dithio esters: correlation of resonance Raman spectra with structures

    International Nuclear Information System (INIS)

    Lee, H.; Angus, R.H.; Storer, A.C.; Varughese, K.I.; Carey, P.R.

    1988-01-01

    The conformational states of N-acylalanine dithio esters, involving rotational isomers about the RC(=O)NH-CH(CH 3 ) and NHCH(CH 3 )-C(=S) bonds, are defined and compared to those of N-acylglycine dithio esters. The structure of N-(p-nitrobenzoyl)-DL-alanine ethyl dithio ester has been determined by X-ray crystallographic analysis; it is a B-type conformer with the amide N atom cis to the thiol sulfur. Raman and resonance Raman (RR) measurements on this compound and for the B conformers of solid N-benzoyl-DL-alanine ethyl dithio ester and N-(β-phenylpropionyl)-DL-alanine ethyl dithio ester and its NHCH(CD 3 )C(=S) and NHCH(CH 3 ) 13 C(=S) analogues are used to set up a library of RR data for alanine-based dithio esters in a B-conformer state. RR data for this solid material in its isotopically unsubstituted and CH(C-D 3 )C(=S) and CH(CH 3 ) 13 C(=S) forms provide information on the RR signatures of alanine dithio esters in A-like conformations. RR spectra are compared for the solid compounds, for N-(p-nitrobenzoyl)-DL-alanine, N-(β-phenylpropionyl)-DL-alanine, and (methyloxycarbonyl)-L-phenylalanyl-DL-alanine ethyl dithio ester, and for several 13 C=S- and CD 3 -substituted analogues in CCl 4 or aqueous solutions. The RR data demonstrate that the alanine-based dithio esters take up A, B, and C 5 conformations in solution. The RR spectra of these conformers are clearly distinguishable from those for the same conformers of N-acylglycine dithio esters. However, the crystallographic and spectroscopic results show that the results show that the conformational properties of N-acylglycine and N-acylalanine dithio esters are very similar

  9. Synthesis and characterization of ester and amide derivatives of titanium(IV) carboxymethylphosphonate

    International Nuclear Information System (INIS)

    Melánová, Klára; Beneš, Ludvík; Trchová, Miroslava; Svoboda, Jan; Zima, Vítězslav

    2013-01-01

    A set of layered ester and amide derivatives of titanium(IV) carboxymethylphosphonate was prepared by solvothermal treatment of amorphous titanium(IV) carboxymethylphosphonate with corresponding 1-alkanols, 1,ω-alkanediols, 1-aminoalkanes, 1,ω-diaminoalkanes and 1,ω-amino alcohols and characterized by powder X-ray diffraction, IR spectroscopy and thermogravimetric analysis. Whereas alkyl chains with one functional group form bilayers tilted to the layers, 1,ω-diaminoalkanes and most of 1,ω-alkanediols form bridges connecting the adjacent layers. In the case of amino alcohols, the alkyl chains form bilayer and either hydroxyl or amino group is used for bonding. This simple method for the synthesis of ester and amide derivatives does not require preparation of acid chloride derivative as a precursor or pre-intercalation with alkylamines and can be used also for the preparation of ester and amide derivatives of titanium carboxyethylphosphonate and zirconium carboxymethylphosphonate. - Graphical abstract: Ester and amide derivatives of layered titanium carboxymethylphosphonate were prepared by solvothermal treatment of amorphous solid with alkanol or alkylamine. - Highlights: • Ester and amide derivatives of titanium carboxymethylphosphonate. • Solvothermal treatment of amorphous solid with alkanol or alkylamine. • Ester and amide formation confirmed by IR spectroscopy

  10. Long-Acting Diclofenac Ester Prodrugs for Joint Injection

    DEFF Research Database (Denmark)

    Mertz, Nina; Larsen, Susan Weng; Kristensen, Jesper

    2016-01-01

    A prodrug approach for local and sustained diclofenac action after injection into joints based on ester prodrugs having a pH-dependent solubility is presented. Inherent ester prodrug properties influencing the duration of action include their pH-dependent solubility and charge state, as well...... as susceptibility to undergo esterase facilitated hydrolysis. In this study, physicochemical properties and pH rate profiles of 3 diclofenac ester prodrugs differing with respect to the spacer carbon chain length between the drug and the imidazole-based promoiety were determined and a rate equation for prodrug...... degradation in aqueous solution in the pH range 1-10 was derived. In the pH range 6-10, the prodrugs were subject to parallel degradation to yield diclofenac and an indolinone derivative. The prodrug degradation was found to be about 6-fold faster in 80% (vol/vol) human plasma as compared to 80% (vol...

  11. Boric Ester-Type Molten Salt via Dehydrocoupling Reaction

    Directory of Open Access Journals (Sweden)

    Noriyoshi Matsumi

    2014-11-01

    Full Text Available Novel boric ester-type molten salt was prepared using 1-(2-hydroxyethyl-3-methylimidazolium chloride as a key starting material. After an ion exchange reaction of 1-(2-hydroxyethyl-3-methylimidazolium chloride with lithium (bis-(trifluoromethanesulfonyl imide (LiNTf2, the resulting 1-(2-hydroxyethyl-3-methylimidazolium NTf2 was reacted with 9-borabicyclo[3.3.1]nonane (9-BBN to give the desired boric ester-type molten salt in a moderate yield. The structure of the boric ester-type molten salt was supported by 1H-, 13C-, 11B- and 19F-NMR spectra. In the presence of two different kinds of lithium salts, the matrices showed an ionic conductivity in the range of 1.1 × 10−4–1.6 × 10−5 S cm−1 at 51 °C. This was higher than other organoboron molten salts ever reported.

  12. Saliva-catalyzed hydrolysis of a ketobemidone ester prodrug

    DEFF Research Database (Denmark)

    Hansen, L.B.; Christrup, Lona Louring; Bundgaard, H.

    1992-01-01

    Saliva enzyme-catalysed hydrolysis of ester prodrugs or drugs containing sensitive ester groups may be a limiting factor for the buccal absorption of such compounds. Using the isopropyl carbonate ester of ketobemidone as a model substance of a hydrolysis-sensitive prodrug the esterase activity...... of human saliva has been characterized as a function of various factors. The esterase activity was found to decrease rapidly upon storage of the saliva at 37°C. The activity increased with increasing pH in the range 4.5-7.4 and with increasing salivation flow rate up to a rate of 0.9 ml min. Under resting...... conditions, the flow rate was about 0.2 ml min which implied a greatly decreased esterase activity. The activity was highest after fasting and decreased after intake of a meal. The intraindividual variation in the saliva esterase activity was small whereas a larger interindividual variation was found....

  13. [Development of the determination methods of fatty acid esters of chloropropanediols in fat-rich foods].

    Science.gov (United States)

    Yan, Xiaobo; Wu, Shaoming; Li, Nan; Lü, Huadong; Fu, Wusheng

    2013-02-01

    Fatty acid esters of chloropropanediols are a kinds of newly emerged food contaminants, especially 3-monochloropropane-1,2-diol (3-MCPD) esters that have been detected in many foodstuffs such as infant formula and edible oils at relatively high levels. Based on the Tolerable Dose Intake (TDI) of 3-MCPD, the intake of 3-MCPD from 3-MCPD esters may cause the health risk to human beings. The researches for the analysis of 3-MCPD esters have been carried out in some institutes abroad, but there were only a few in China. This paper reviews the methods for the determination of 3-MCPD esters in fat-rich foods, including the extraction, hydrolysis, the derivatization of 3-MCPD esters, the total amount of 3-MCPD esters and the amounts of monoesters and diesters of 3-MCPD.

  14. 13-week oral toxicity study with stanol esters in rats

    NARCIS (Netherlands)

    Turnbull, D.; Whittaker, M.H.; Frankos, V.H.; Jonker, D.

    1999-01-01

    Plant sterols and their saturated derivatives, known as stanols, reduce serum cholesterol when consumed in amounts of approximately 2 g per day. Stanol fatty acid esters have been developed as a highly fat-soluble form that may lower cholesterol more effectively than stanols. Stanol esters occur

  15. Triazole–Au(I complex as chemoselective catalyst in promoting propargyl ester rearrangements

    Directory of Open Access Journals (Sweden)

    Dawei Wang

    2011-07-01

    Full Text Available Triazole–Au (TA–Au catalysts were employed in several transformations involving propargyl ester rearrangement. Good chemoselectivity was observed, which allowed the effective activation of the alkyne without affecting the reactivity of the allene ester intermediates. These results led to the investigation of the preparation of allene ester intermediates with TA–Au catalysts under anhydrous conditions. As expected, the desired 3,3-rearrangement products were obtained in excellent yields (generally >90% yields with 1% loading. Besides the typical ester migrating groups, carbonates and carbamates were also found to be suitable for this transformation, which provided a highly efficient, practical method for the preparation of substituted allenes.

  16. PROCESS FOR HYDROGENOLYSIS OF ALPHA-HYDROXY ESTERS OR ACIDS USING A HETEROGENEOUS CATALYST

    DEFF Research Database (Denmark)

    2017-01-01

    The present invention relates to a method for hydrogenolysis of alpha-hydroxy esters or acids, comprising reacting the alpha-hydroxy ester or acid in the presence of a heterogeneous catalyst. The present invention also relates to a method for producing propionic acid ester, and the use of any...

  17. Ester-free Thiol-X Resins: New Materials with Enhanced Mechanical Behavior and Solvent Resistance.

    Science.gov (United States)

    Podgórski, Maciej; Becka, Eftalda; Chatani, Shunsuke; Claudino, Mauro; Bowman, Christopher N

    A series of thiol-Michael and radical thiol-ene network polymers were successfully prepared from ester-free as well as ester-containing monomer formulations. Polymerization reaction rates, dynamic mechanical analysis, and solvent resistance experiments were performed and compared between compositions with varied ester loading. The incorporation of ester-free alkyl thiol, vinyl sulfone and allylic monomers significantly improved the mechanical properties when compared with commercial, mercaptopropionate-based thiol-ene or thiol-Michael networks. For polymers with no hydrolytically degradable esters, glass transition temperatures (T g 's) as high as 100 °C were achieved. Importantly, solvent resistance tests demonstrated enhanced stability of ester-free formulations over PETMP-based polymers, especially in concentrated basic solutions. Kinetic analysis showed that glassy step-growth polymers are readily formed at ambient conditions with conversions reaching 80% and higher.

  18. Synthesis of chiral N-phosphinyl α-imino esters and their application in asymmetric synthesis of α-amino esters by reduction

    Directory of Open Access Journals (Sweden)

    Yiwen Xiong

    2014-03-01

    Full Text Available A variety of chiral N-phosphinyl α-imino esters have been synthesized for the first time from ketoesters and phosphinylamide, which were then reduced by L-selectride to give the corresponding N-phosphinyl-protected α-amino esters. The reduction proceeded very well with excellent chemical yields (88–98% as well as high diastereoselectivities (96:4 to 99:1. Some of these products could be obtained without column chromatography and recrystallization. The chiral phosphinyl auxiliary could be easily cleaved under acidic conditions.

  19. Effect of Sucrose Esters on the Physicochemical Properties of Wheat ...

    African Journals Online (AJOL)

    HP

    Purpose: To investigate the effect of sucrose esters on the physicochemical properties of wheat starch. Methods: Sucrose ester was mixed with wheat starch extracted from normal soft wheat cultivars and heated. Change in starch properties arising from the interaction between were assessed for starch blue value, viscosity ...

  20. Isolation, Fractionation, and Identification of Sucrose Esters from Various Oriental Tobaccos Employing Supercritical Fluids

    Directory of Open Access Journals (Sweden)

    Ashraf-Khorassani M

    2014-12-01

    Full Text Available Isolation, fractionation, and identification of sucrose esters from aged oriental tobacco employing supercritical fluids have been completed. Underivatized sucrose ester-rich extracts were obtained using supercritical CO2 at densities greater than 0.73 g/mL. Lower density CO2 provided extracts with notable amounts of tobacco derived material; yet, no detectable sucrose ester content. Preparative supercritical fluid chromatography (SFC provided for an additional purification of the sucrose ester-enriched fraction after column optimization. Structural assignments of the SFC fractions were facilitated using gas chromatography/mass spectrometry (GC/MS accompanied by N, O-bis(trimethylsilyltrifluoroacetamide-dimethylformamide (BSTFA-DMF derivatization of the free hydroxyl groups and high performance-liquid chromatography/mass spectrometry (HPLC/MS. From a relative quantitative perspective regardless of tobacco type, sucrose esters having an acetyl group on C6 of the glucose function (Group III were in higher concentration compared to both the concentration observed for sucrose ester of Group I (acetyl group on C3 of fructose and sucrose ester of Group II (no acetyl group on either glucose or fructose. Saturated fatty acid constituents were found to range from a maximum total of 18 carbons to a minimum total of 13 carbons. Unsaturated and isomeric fatty acid homologues were detected within the Group II sucrose ester.

  1. REPRODUCTIVE TOXICITY OF PHTHALATE ESTERS

    Science.gov (United States)

    Phthalate esters display several modes of toxicity in mammalian species. In the rat, in utero exposure at relatively low dosage levels disrupts development of the reproductive system of the male rat by altering fetal testis hormone production. This presentation is a review of t...

  2. Tribochemical behaviors of phosphite esters and their combinations with alkyl amines

    International Nuclear Information System (INIS)

    Fu, Xisheng; Sun, Lingguo; Zhou, Xuguang; Li, Jianchang; Fan, Bingji; Ren, Tianhui

    2015-01-01

    Highlights: • Investigating the differences of tribological performance between phosphite ester and their combinations with alkyl amines. • The combination of SEM and EDS was used to investigate the worn surface morphology and detect the element distributions and content on the steel surface. • The chemical compositions of the thermal films and tribofilms were characterized by TEY P L-edge and FY P K-edge XANES spectroscopy. • A phosphate and polyphosphate tribofilm was formed after rubbing times of even 10 s, and being formed completely after rubbing times of 10 min. • Phosphite ester forms short-chain polyphosphates, and ammonium phosphite produces medium-chain polyphosphates in the tribfilm. - Abstract: The tribochemical behaviors of dioctylphosphite ester and ditetradecylphosphite ester together with their corresponding combinations with alkyl amines were studied. The results of tribological evaluations showed that the phosphite ester with long alkyl chain exhibited better antiwear performance but worse extreme pressure property than that of the phosphite ester with short alkyl chain. The combinations showed better antiwear performance but worse extreme pressure property than their corresponding phosphite esters. Scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) were used to investigate the worn surface morphology and the content as well as the distribution of active elements. It can be found that the prorupt edges of worn surface are enriched with phosphoric-oxygenic compounds and less phosphoric-oxygenic compounds were detected in the valley. X-ray absorption near-edge structure (XANES) spectroscopy was employed to explore the chemical nature of the worn surface. The results show that a tribofilm composed of phosphates and polyphosphates is formed on the worn surface. Furthermore, the tribofilm is generated even in a rubbing of 10 s and is formed completely after 10 min rubbing.

  3. Structural characterization of saturated branched chain fatty acid methyl esters by collisional dissociation of molecular ions generated by electron ionization[S

    Science.gov (United States)

    Ran-Ressler, Rinat R.; Lawrence, Peter; Brenna, J. Thomas

    2012-01-01

    Saturated branched chain fatty acids (BCFA) are present as complex mixtures in numerous biological samples. The traditional method for structure elucidation, electron ionization (EI) mass spectrometry, sometimes does not unambiguously enable assignment of branching in isomeric BCFA. Zirrolli and Murphy (Zirrolli , J. A. , and R. A. Murphy. 1993. Low-energy tandem mass spectrometry of the molecular ion derived from fatty acid methyl esters: a novel method for analysis of branched-chain fatty acids. J. Am. Soc. Mass Spectrom. 4: 223–229.) showed that the molecular ions of four BCFA methyl ester (BCFAME) yield highly characteristic fragments upon collisional dissociation using a triple quadrupole instrument. Here, we confirm and extend these results by analysis using a tabletop 3-D ion trap for activated molecular ion EI-MS/MS to 30 BCFAME. iso-BCFAME produces a prominent ion (30-100% of base peak) for [M-43] (M-C3H7), corresponding to the terminal isopropyl moiety in the original iso-BCFAME. Anteiso-FAME yield prominent ions (20-100% of base peak) corresponding to losses on both side of the methyl branch, [M-29] and [M-57], and tend to produce more prominent m/z 115 peaks corresponding to a cyclization product around the ester. Dimethyl and tetramethyl FAME, with branches separated by at least one methylene group, yield fragment on both sides of the sites of methyl branches that are more than 6 C away from the carboxyl carbon. EI-MS/MS yields uniquely specific ions that enable highly confident structural identification and quantification of BCFAME. PMID:22021637

  4. Repellent activity of monoterpenoid esters with neurotransmitter amino acids against yellow fever mosquito, Aedes aegypti

    Directory of Open Access Journals (Sweden)

    Nesterkina Mariia

    2018-03-01

    Full Text Available Repellent activity of monoterpenoid esters (1-6 with neurotransmitter amino acids (GABA and glycine was investigated against Aedes aegypti by using a “cloth-patch” assay and compared to reference standard N,N-diethyl-3-methylbenzamide (DEET. Monoterpenoid esters showed repellent activity with minimum effective dosages (MED in the range of 0.031-0.469 mg/cm2. The carvacrol ester of GABA (2, MED of 0.031 ± 0.008 mg/cm2 exhibited the highest repellency of six monoterpenoid esters tested in comparison to the standard repellent DEET (MED of 0.009 ± 0.002 mg/cm2; however, the repellent activity of carvacrol-glycine ester (5 decreased 4-fold compared to the carvacrol-GABA derivative (2. The repellent activities of menthol GABA (1, MED= 0.375 ± 0.000 mg/cm2 and glycine ester (4, MED=0.312 ± 0.063 mg/cm2 were similar The guaiacol-glycine ester (6 was 3.75-fold more efficacious than the guaiacol ester of GABA (3. In the present study, we report repellent efficacy of prolonged exposure to GABA and glycine esters of menthol, carvacrol, guaiacol (1-6 as compared to the repellent activities of their monoterpene moieties alone.

  5. Impact of thermooxidation of phytosteryl and phytostanyl fatty acid esters on cholesterol micellarization in vitro.

    Science.gov (United States)

    Scholz, Birgit; Weiherer, Renate; Engel, Karl-Heinz

    2017-09-01

    The effects of thermooxidation of a phytosteryl/-stanyl and a phytostanyl fatty acid ester mixture on cholesterol micellarization were investigated using an in vitro digestion model simulating enzymatic hydrolysis by cholesterol esterase and subsequent competition of the liberated phytosterols/-stanols with cholesterol for incorporation into mixed micelles. As a first step, relationships between different doses of the ester mixtures and the resulting micellarized cholesterol were established. Subsequent subjection of the thermooxidized ester mixtures to the in vitro digestion model resulted in three principal observations: (i) thermal treatment of the ester mixtures led to substantial decreases of the intact esters, (ii) in vitro digestion of cholesterol in the presence of the thermooxidized ester mixtures resulted in significant increases of cholesterol micellarization, and (iii) the extents of the observed effects on cholesterol micellarization were strongly associated to the remaining contents of intact esters. The loss of efficacy to inhibit cholesterol micellarization due to thermally induced losses of intact esters corresponded to a loss of efficacy that would have been induced by an actual removal of these amounts of esters prior to the in vitro digestion. The obtained results suggest that in particular oxidative modifications of the fatty acid moieties might be responsible for the observed increases of cholesterol micellarization. Copyright © 2017 Elsevier Inc. All rights reserved.

  6. 40 CFR 721.3800 - Formaldehyde, condensated polyoxyethylene fatty acid, ester with styrenated phenol, ethylene...

    Science.gov (United States)

    2010-07-01

    ... polyoxyethylene fatty acid, ester with styrenated phenol, ethylene oxide adduct. 721.3800 Section 721.3800... Formaldehyde, condensated polyoxyethylene fatty acid, ester with styrenated phenol, ethylene oxide adduct. (a... generically as formaldehyde, condensated polyoxyethylene fatty acid, ester with styrenated phenol, ethylene...

  7. Binding of indomethacin methyl ester to cyclooxygenase-2. A computational study.

    Science.gov (United States)

    Sárosi, Menyhárt-Botond

    2018-06-05

    Inhibitors selective towards the second isoform of prostaglandin synthase (cyclooxygenase, COX-2) are promising nonsteroidal anti-inflammatory drugs and antitumor medications. Methylation of the carboxylate group in the relatively nonselective COX inhibitor indomethacin confers significant COX-2 selectivity. Several other modifications converting indomethacin into a COX-2 selective inhibitor have been reported. Earlier experimental and computational studies on neutral indomethacin derivatives suggest that the methyl ester derivative likely binds to COX-2 with a similar binding mode as that observed for the parent indomethacin. However, docking studies followed by molecular dynamics simulations revealed two possible binding modes in COX-2 for indomethacin methyl ester, which differs from the experimental binding mode found for indomethacin. Both alternative binding modes might explain the observed COX-2 selectivity of indomethacin methyl ester. Graphical abstract Binding of indomethacin methyl ester to cyclooxygenase-2.

  8. Methyl and ethyl soybean esters production

    Energy Technology Data Exchange (ETDEWEB)

    Pighinelli, Anna Leticia Montenegro Turtelli; Park, Kil Jin; Zorzeto, Thais Queiroz [Universidade Estadual de Campinas (FEAGRI/UNICAMP), SP (Brazil). Fac. de Engenharia Agricola], E-mail: annalets@feagri.unicamp.br; Bevilaqua, Gabriela [Universidade Estadual de Campinas (IQ/UNICAMP), SP (Brazil). Inst. de Quimica

    2008-07-01

    Biodiesel is a fuel obtained from triglycerides found in nature, like vegetable oils and animal fats. Nowadays it has been the subject of many researches impulses by the creation of the Brazilian law that determined the blend of 2% of biodiesel with petrodiesel. Basically, there are no limitations on the oilseed type for chemical reaction, but due to high cost of this major feedstock, it is important to use the grain that is available in the region of production. Soybean is the oilseed mostly produced in Brazil and its oil is the only one that is available in enough quantity to supply the current biodiesel demand. The objective of this work was to study the effects of reaction time and temperature on soybean oil transesterification reaction with ethanol and methanol. A central composite experimental design with five variation levels was used and response surface methodology applied for the data analysis. The statistical analysis of the results showed that none of the factors affected the ethyl esters production. However, the methyl esters production suffered the influence of temperature (linear effect), reaction time (linear and quadratic) and interaction of these two variables. None of the generated models showed significant regression consequently it was not possible to build the response surface. The experiments demonstrated that methanol is the best alcohol for transesterification reactions and the ester yield was up to 85%. (author)

  9. A new, direct analytical method using LC-MS/MS for fatty acid esters of 3-chloro-1,2-propanediol (3-MCPD esters) in edible oils.

    Science.gov (United States)

    Yamazaki, K; Ogiso, M; Isagawa, S; Urushiyama, T; Ukena, T; Kibune, N

    2013-01-01

    A new, direct analytical method for the determination of 3-chloro-1,2-propanediol fatty acid esters (3-MCPD esters) was developed. The targeted 3-MCPD esters included five types of monoester and 25 [corrected] types of diester. Samples (oils and fats) were dissolved in a mixture of tert-butyl methyl ether and ethyl acetate (4:1), purified using two solid-phase extraction (SPE) cartridges (C(18) and silica), then analysed by liquid chromatography-tandem mass spectrometry (LC-MS/MS). Five monoesters and five diesters with the same fatty acid group could be separated and quantified. Pairs of 3-MCPD diesters carrying the same two different fatty acid groups, but at reversed positions (sn-1 and sn-2), could not be separated and so were expressed as a sum of both compounds. The limits of quantification (LOQs) were estimated to be between 0.02 to 0.08 mg kg(-1), depending on the types of 3-MCPD ester. Repeatability expressed as relative standard deviation (RSD(r)%) varied from 5.5% to 25.5%. The new method was shown to be applicable to various commercial edible oils and showed levels of 3-MCPD esters varying from 0.58 to 25.35 mg kg(-1). The levels of mono- and diesters ranged from 0.10 to 0.69 mg kg(-1) and from 0.06 to 16 mg kg(-1), respectively.

  10. Increased large VLDL particles confer elevated cholesteryl ester transfer in diabetes

    NARCIS (Netherlands)

    Dullaart, Robin P. F.; de Vries, Rindert; Kwakernaak, Arjan J.; Perton, Frank; Dallinga-Thie, Geesje M.

    BackgroundPlasma cholesteryl ester transfer (CET), reflecting transfer of cholesteryl esters from high density lipoproteins (HDL) towards apolipoprotein B-containing lipoproteins, may promote atherosclerosis development, and is elevated in Type 2 diabetes mellitus (T2DM). We determined the extent to

  11. METODE ESTIMASI PROPERTI KRITIS UAP-CAIR KOMPONEN MURNI ESTER

    Directory of Open Access Journals (Sweden)

    Dhoni Hartantoa

    2014-03-01

    Full Text Available Biodiesel become eco-friendly renewable energy resources which is consisted of monoalkyl ester or long chain fatty acid from plants or animal. Biodiesel has more advantage than petrodiesel. Property of pure compound such as critical properties are the important thing to determine chemical mixtures behavior and also as base of equation of state. Joback method can show good results in estimating critical properties of monoalkyl ester.

  12. Triphenyltin derivatives of sulfanylcarboxylic esters.

    Science.gov (United States)

    Casas, José S; Couce, María D; Sánchez, Agustín; Seoane, Rafael; Sordo, José; Perez-Estévez, Antonio; Vázquez-López, Ezequiel

    2018-03-01

    The reaction of 3-(aryl)-2-sulfanylpropenoic acids [H 2 xspa; x: p=3-phenyl-, f=3-(2-furyl)-, t=3-(2-thienyl)-] with methanol or ethanol gave the corresponding methyl (Hxspme) or ethyl (Hxspee) esters. The reaction of these esters (HL) with triphenyltin(IV) hydroxide gave compounds of the type [SnPh 3 L], which were isolated and characterized as solids by elemental analysis, IR spectroscopy and mass spectrometry and in solution by multinuclear ( 1 H, 13 C and 119 Sn) NMR spectroscopy. The structures of [SnPh 3 (pspme)], [SnPh 3 (fspme)] and [SnPh 3 (fspee)] were determined by X-ray diffractometry and the antimicrobial activity against E. coli, S. aureus, B. subtilis, P. aeruginosa, Resistant P. aeruginosa (a strain resistant to 'carbapenem'), and C. albicans was tested and the in vitro cytotoxic activity against the HeLa-229, A2780 and A2780cis cell lines was determined for all compounds. Copyright © 2017 Elsevier Inc. All rights reserved.

  13. Stereoselective formation of a cholesterol ester conjugate from fenvalerate by mouse microsomal carboxyesterase(s).

    Science.gov (United States)

    Miyamoto, J; Kaneko, H; Takamatsu, Y

    1986-06-01

    In accordance with in vivo findings, of the four chiral isomers of fenvalerate (S-5602 Sumicidin, Pydrin, [RS]-alpha-cyano-3-phenoxybenzyl [RS]-2-(4-chlorophenyl)isovalerate), only the [2R, alpha S]-isomer (B-isomer) yielded cholesteryl [2R]-2-(4-chlorophenyl)isovalerate (CPIA-cholesterol ester) in the in vitro study using several tissue homogenates of mice, rats, dogs, and monkeys. There were species differences in the extent of CPIA-cholesterol-ester formation, with mouse tissues showing relatively higher activity than those of other animals. The kidney, brain, and spleen of mice showed relatively higher capacities to form this ester compared to other tissues, and the enzyme activity was mainly localized in microsomal fractions. The CPIA-cholesterol ester did not seem to be produced by three known biosynthetic pathways of endogenous cholesterol esters--acyl-CoA:cholesterol O-acyltransferase (ACAT), lecithin:cholesterol O-acyltransferase (LCAT), and cholesterol esterase. Carboxyesterase(s) of mouse kidney microsomes solubilized by digitonin hydrolyzed only the B alpha-isomer of fenvalerate, yielding CPIA, whereas they yielded the corresponding cholesterol ester in the presence of artificial liposomes containing cholesterol. Thus, it appears that the stereoselective formation of the CPIA-cholesterol ester results from the stereoselective formation of the CPIA-carboxyesterase complex only from the B alpha-isomer, which subsequently undergoes cleavage by cholesterol to yield the CPIA-cholesterol ester.

  14. Production of wax esters via microbial oil synthesis from food industry waste and by-product streams.

    Science.gov (United States)

    Papadaki, Aikaterini; Mallouchos, Athanasios; Efthymiou, Maria-Nefeli; Gardeli, Chryssavgi; Kopsahelis, Nikolaos; Aguieiras, Erika C G; Freire, Denise M G; Papanikolaou, Seraphim; Koutinas, Apostolis A

    2017-12-01

    The production of wax esters using microbial oils was demonstrated in this study. Microbial oils produced from food waste and by-product streams by three oleaginous yeasts were converted into wax esters via enzymatic catalysis. Palm oil was initially used to evaluate the influence of temperature and enzyme activity on wax ester synthesis catalysed by Novozyme 435 and Lipozyme lipases using cetyl, oleyl and behenyl alcohols. The highest conversion yields (up to 79.6%) were achieved using 4U/g of Novozyme 435 at 70°C. Transesterification of microbial oils to behenyl and cetyl esters was achieved at conversion yields up to 87.3% and 69.1%, respectively. Novozyme 435 was efficiently reused for six and three cycles during palm esters and microbial esters synthesis, respectively. The physicochemical properties of microbial oil derived behenyl esters were comparable to natural waxes. Wax esters from microbial oils have potential applications in cosmetics, chemical and food industries. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Three new fatty acid esters from the mushroom Boletus pseudocalopus.

    Science.gov (United States)

    Kim, Ki Hyun; Choi, Sang Un; Lee, Kang Ro

    2012-06-01

    A bioassay-guided fractionation and chemical investigation of a MeOH extract of the Korean wild mushroom Boletus pseudocalopus resulted in the identification of three new fatty acid esters, named calopusins A-C (1-3), along with two known fatty acid methyl esters (4-5). These new compounds are structurally unique fatty acid esters with a 2,3-butanediol moiety. Their structures were elucidated through 1D- and 2D-NMR spectroscopic data and GC-MS analysis as well as a modified Mosher's method. The new compounds 1-3 showed significant inhibitory activity against the proliferation of the tested cancer cell lines with IC(50) values in the range 2.77-12.51 μM.

  16. Improvement of Fructanohydrolase Production in Aspergillus niger SL-09 by Sucrose Ester

    Directory of Open Access Journals (Sweden)

    Xiang-Yang Ge

    2006-01-01

    Full Text Available The influence of carbon sources, nitrogen sources, and the addition of sucrose ester on fructanohydrolase production was investigated. The enzyme production varied depending on the carbon source. Apart from that, it was found that the enzyme activities formed by Aspergillus niger SL-09 were enhanced dramatically by the addition of sucrose ester S-770 to the medium. The effect of sucrose ester on enzyme production was also studied on molecular level, and it was confirmed that the transcription was activated by the addition of sucrose ester to the medium. The response surface methodology (RSM was used to optimize the composition for the production of fructanohydrolase, and the enzyme activities were enhanced more than 7-fold than those obtained in the basal medium.

  17. One-pot synthesis of thermoplastic mixed paramylon esters using trifluoroacetic anhydride.

    Science.gov (United States)

    Shibakami, Motonari; Tsubouchi, Gen; Sohma, Mitsugu; Hayashi, Masahiro

    2015-03-30

    Mixed paramylon esters prepared from paramylon (a storage polysaccharide of Euglena), acetic acid, and a long-chain fatty acid by one-pot synthesis using trifluoroacetic anhydride as a promoter and solvent were shown to have thermoplasticity. Size exclusion chromatography indicated that the mixed paramylon esters had a weight average molecular weight of approximately 4.9-6.7×10(5). Thermal analysis showed that these esters were stable in terms of the glass transition temperature (>90°C) and 5% weight loss temperature (>320°C). The degree of substitution of the long alkyl chain group, a dominant factor determining thermoplasticity, was controlled by tuning the feed molar ratio of acetic acid and long-chain fatty acid to paramylon. These results implied that the one-pot synthesis is useful for preparing structurally-well defined thermoplastic mixed paramylon esters with high molecular weight. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Hydrolytic Stability of Boronate Ester-Linked Covalent Organic Frameworks

    KAUST Repository

    Li, Huifang

    2018-01-30

    The stability of covalent organic frameworks (COFs) is essential to their applications. However, the common boronate ester-linked COFs are susceptible to attack by nucleophiles (such as water molecules) at the electron-deficient boron sites. To provide an understanding of the hydrolytic stability of the representative boronate ester-linked COF-5 and of the associated hydrolysis mechanisms, density functional theory (DFT) calculations were performed to characterize the hydrolysis reactions of the molecule formed by the condensation of 1,4-phenylenebis(boronic acid) (PBBA) and 2,3,6,7,10,11-hexahydroxytriphenylene (HHTP) monomers; two cases were considered, one dealing with the freestanding molecule and the other with the molecule interacting with COF layers. It was found that the boronate ester (B–O) bond dissociation, which requires one H2O molecule, has a relatively high energy barrier of 22.3 kcal mol−1. However, the presence of an additional H2O molecule significantly accelerates hydrolysis by reducing the energy barrier by a factor of 3. Importantly, the hydrolysis of boronate ester bonds situated in a COF environment follows reaction pathways that are different and have increased energy barriers. These results point to an enhanced hydrolytic stability of COF-5 crystals.

  19. Chemical modifications of Sterculia foetida L. oil to branched ester derivatives

    NARCIS (Netherlands)

    Manurung, Robert; Daniel, Louis; van de Bovenkamp, Hendrik H.; Buntara, Teddy; Maemunah, Siti; Kraai, Gerard; Makertihartha, I. G. B. N.; Broekhuis, Antonius A.; Heeres, Hero J.

    An experimental study to modify Sterculia foetida L. oil (STO) or the corresponding methyl esters (STO FAME) to branched ester derivatives is reported. The transformations involve conversion of the cyclopropene rings in the fatty acid chains of STO through various catalytic as well as stoichiometric

  20. Physical and mechanical testing of essential oil-embedded cellulose ester films

    Science.gov (United States)

    Polymer films made from cellulose esters are useful for embedding plant essential oils, either for food packaging or air freshener applications. Studies and testing were done on the physical and mechanical properties of cellulose ester-based films incorporating essential oils (EO) from lemongrass (C...

  1. Tumor-promoting phorbol esters effect alkalinization of canine renal proximal tubular cells

    International Nuclear Information System (INIS)

    Mellas, J.; Hammerman, M.R.

    1986-01-01

    We have demonstrated the presence of specific receptors for tumor-promoting phorbol esters in the plasma membrane of the canine renal proximal tubular cell. These compounds affect proximal tubular metabolism in vitro. For example, we have shown that they inhibit gluconeogenesis in canine renal proximal tubular segments. Tumor-promoting phorbol esters have been shown to effect alkalinization of non-renal cells, by enhancing Na + -H + exchange across the plasma membrane. To determine whether the actions of tumor-promoting phorbol esters in proximal tubular segments might be mediated by a similar process, we incubated suspensions of segments from dog kidney with these compounds and measured changes in intracellular pH using [ 14 C]-5,5-dimethoxazoladine-2-4-dione (DMO) and flow dialysis. Incubation of segments with phorbol 12,13 dibutyrate, but not inactive phorbol ester, 4 γ phorbol, effected alkalinization of cells within the segments in a concentration-dependent manner. Alkalinization was dependent upon the presence of extracellular [Na + ] > intracellular [Na + ], was prevented by amiloride and was demonstrable in the presence of SITS. Our findings suggest that tumor-promoting esters stimulate the Na + -H + exchanger known to be present in the brush border membrane of the renal proximal tubular cell. It is possible that the stimulation reflects a mechanism by which phorbol esters affect metabolic processes in these cells

  2. Sinapate esters provide greater UV-B attenuation than flavonoids in Arabidopsis thaliana (Brassicaceae)

    International Nuclear Information System (INIS)

    Sheahan, J.J.

    1996-01-01

    Mutants affected in flavonoid (tt4) or sinapate ester (fah1) biosynthesis were used to assess the relative importance of these phenolic UV photoprotectants in Arabidopsis. Flavonoid and sinapate ester absorption was more specific for UV-B than major nonphenolic chromophores in crude extracts. A new method of evaluating phenolic UV-B attenuation was developed using fluorescence analysis. When excited by UV-B, sinapate ester containing leaves and cotyledons had enhanced sinapate ester fluorescence and reduced chlorophyll fluorescence relative to those without sinapate esters. Although fluorescence analysis gave no evidence of UV-B attenuation by flavonoids, enhanced chlorophyll and protein loss were observed upon UV-B exposure in flavonoid-deficient leaves, suggesting they have another mechanism of UV-B protection. The hydroxycinnamates have been largely ignored as UV-B attenuating pigments. and the results indicate that greater attention should be paid to their role in attenuating UV-B

  3. Orally administered glycidol and its fatty acid esters as well as 3-MCPD fatty acid esters are metabolized to 3-MCPD in the F344 rat.

    Science.gov (United States)

    Onami, Saeko; Cho, Young-Man; Toyoda, Takeshi; Akagi, Jun-ichi; Fujiwara, Satoshi; Ochiai, Ryosuke; Tsujino, Kazushige; Nishikawa, Akiyoshi; Ogawa, Kumiko

    2015-12-01

    IARC has classified glycidol and 3-monochloropropane-1,2-diol (3-MCPD) as group 2A and 2B, respectively. Their esters are generated in foodstuffs during processing and there are concerns that they may be hydrolyzed to the carcinogenic forms in vivo. Thus, we conducted two studies. In the first, we administered glycidol and 3-MCPD and associated esters (glycidol oleate: GO, glycidol linoleate: GL, 3-MCPD dipalmitate: CDP, 3-MCPD monopalmitate: CMP, 3-MCPD dioleate: CDO) to male F344 rats by single oral gavage. After 30 min, 3-MCPD was detected in serum from all groups. Glycidol was detected in serum from the rats given glycidol or GL and CDP and CDO in serum from rats given these compounds. In the second, we examined if metabolism occurs on simple reaction with rat intestinal contents (gastric, duodenal and cecal contents) from male F344 gpt delta rats. Newly produced 3-MCPD was detected in all gut contents incubated with the three 3-MCPD fatty acid esters and in gastric and duodenal contents incubated with glycidol and in duodenal and cecal contents incubated with GO. Although our observation was performed at 1 time point, the results showed that not only 3-MCPD esters but also glycidol and glycidol esters are metabolized into 3-MCPD in the rat. Copyright © 2015 Elsevier Inc. All rights reserved.

  4. Naturally occurring antifungal aromatic esters and amides

    International Nuclear Information System (INIS)

    Ali, M.S.; Shahnaz; Tabassum, S.; Ogunwande, I.A.; Pervez, M.K.

    2010-01-01

    During the search of antifungal natural products from terrestrial plants, a new long chained aromatic ester named grandiflorate along with spatazoate from Portulaca grandiflora and N-[2-methoxy-2-(4-methoxyphenyl) ethyl]-trans-cinnamide and aegeline from Solanum erianthum of Nigeria were isolated and tested against six fungal species. The known constituents have not been reported so far from mentioned investigated plants. Structures of the isolated compounds were elucidated with the aid of spectroscopic techniques including two dimensional NMR experiments. Among the compounds, the esters found more potent than amides against Candida albicans and Aspergillus flavus. The new compound grandiflorate gave response against all tested fungal species while aegeline was found to give lowest inhibition during this study. (author)

  5. Naturally occurring antifungal aromatic esters and amides

    Energy Technology Data Exchange (ETDEWEB)

    Ali, M S; Shahnaz,; Tabassum, S; Ogunwande, I A; Pervez, M K [University of Karachi (Pakistan). HEJ Research Inst. of Chemistry, International Centre for Chemical and Biological Sciences

    2010-08-15

    During the search of antifungal natural products from terrestrial plants, a new long chained aromatic ester named grandiflorate along with spatazoate from Portulaca grandiflora and N-[2-methoxy-2-(4-methoxyphenyl) ethyl]-trans-cinnamide and aegeline from Solanum erianthum of Nigeria were isolated and tested against six fungal species. The known constituents have not been reported so far from mentioned investigated plants. Structures of the isolated compounds were elucidated with the aid of spectroscopic techniques including two dimensional NMR experiments. Among the compounds, the esters found more potent than amides against Candida albicans and Aspergillus flavus. The new compound grandiflorate gave response against all tested fungal species while aegeline was found to give lowest inhibition during this study. (author)

  6. Use of tobacco seed oil methyl ester in a turbocharged indirect injection diesel engine

    International Nuclear Information System (INIS)

    Usta, N.

    2005-01-01

    Vegetable oils and their methyl/ethyl esters are alternative renewable fuels for compression ignition engines. Different kinds of vegetable oils and their methyl/ethyl esters have been tested in diesel engines. However, tobacco seed oil and tobacco seed oil methyl ester have not been tested in diesel engines, yet. Tobacco seed oil is a non-edible vegetable oil and a by-product of tobacco leaves production. To the author's best knowledge, this is the first study on tobacco seed oil methyl ester as a fuel in diesel engines. In this study, potential tobacco seed production throughout the world, the oil extraction process from tobacco seed and the transesterification process for biodiesel production were examined. The produced tobacco seed oil methyl ester was characterized by exposing its major properties. The effects of tobacco seed oil methyl ester addition to diesel No. 2 on the performance and emissions of a four cycle, four cylinder turbocharged indirect injection (IDI) diesel engine were examined at both full and partial loads. Experimental results showed that tobacco seed oil methyl ester can be partially substituted for the diesel fuel at most operating conditions in terms of performance parameters and emissions without any engine modification and preheating of the blends. (Author)

  7. Maximization of fructose esters synthesis by response surface methodology.

    Science.gov (United States)

    Neta, Nair Sampaio; Peres, António M; Teixeira, José A; Rodrigues, Ligia R

    2011-07-01

    Enzymatic synthesis of fructose fatty acid ester was performed in organic solvent media, using a purified lipase from Candida antartica B immobilized in acrylic resin. Response surface methodology with a central composite rotatable design based on five levels was implemented to optimize three experimental operating conditions (temperature, agitation and reaction time). A statistical significant cubic model was established. Temperature and reaction time were found to be the most significant parameters. The optimum operational conditions for maximizing the synthesis of fructose esters were 57.1°C, 100 rpm and 37.8 h. The model was validated in the identified optimal conditions to check its adequacy and accuracy, and an experimental esterification percentage of 88.4% (±0.3%) was obtained. These results showed that an improvement of the enzymatic synthesis of fructose esters was obtained under the optimized conditions. Copyright © 2011 Elsevier B.V. All rights reserved.

  8. Anti-oedematous activities of the main triterpendiol esters of marigold (Calendula officinalis L.).

    Science.gov (United States)

    Zitterl-Eglseer, K; Sosa, S; Jurenitsch, J; Schubert-Zsilavecz, M; Della Loggia, R; Tubaro, A; Bertoldi, M; Franz, C

    1997-07-01

    Separation and isolation of the genuine faradiol esters (1, 2) from flower heads of Marigold (Calendula (officinalis L., Asteraceae) could be achieved by means of repeated column chromatography (CC) and HPLC for the first time. Structure elucidation of faradiol-3-myristic acid ester 1, faradiol-3-palmitic acid ester 2 and psi-taraxasterol 3 has been also performed, without any previous degradation by means of MS, 1H-NMR, 13C-NMR and 2D-NMR experiments. The anti-oedematous activities of these three compounds were tested by means of inhibition of Croton oil-induced oedema of the mouse ear. Both faradiol esters showed nearly the same dose dependent anti-oedematous activity and no significant synergism appeared with their mixture. The free monol, psi-taraxasterol, had a slightly lower effect. Furthermore, faradiol was more active than its esters and than psi-taraxasterol and showed the same effect as an equimolar dose of indomethacin.

  9. Synthesis and cytotoxicity of boronated fatty esters for BNCT of cervix cancer

    International Nuclear Information System (INIS)

    Tambunchong, C.; Prachayasittikul, S.; Picha, P.; Tumpum, C.

    2000-01-01

    Esterification reactions of o-carboranic acid with six fatty alcohols, palmitoleyl, stearyl, oleyl, elaidyl, linoleyl and linoelaidyl alcohols, proceeded smoothly under nitrogen atmosphere with dimethylamino pyrimidine as a catalyst. The reaction gave the corresponding esters in moderate yields. Most of the synthetic esters are stable at room temperature except the linoleyl carboranate and linoelaidyl carboranate which decomposed within two weeks. The in vitro studies on Hela cells showed relatively low cytotoxic. The IC 50 of boronated esters were in range of 36-83 micrograms/cm 3 . (author)

  10. N-Acetyl-D- and L-esters of 5'-AMP hydrolyze at different rates

    Science.gov (United States)

    Wickramasinghe, N. S.; Lacey, J. C. Jr; Lacey JC, J. r. (Principal Investigator)

    1993-01-01

    Studies of the properties of aminoacyl derivatives of 5'-AMP are aimed at understanding the origin of the process of protein synthesis. Aminoacyl (2',3') esters of 5'-AMP can serve as models of the 3'-terminus of aminoacyl tRNA. We report here on the relative rates of hydrolysis of Ac-D- and L-Phe AMP esters as a function of pH. At all pHs above 3, the rate constant of hydrolysis of the Ac-L-Phe ester is 1.7 to 2.1 times that of Ac-D-Phe ester. The D-isomer seems partially protected from hydrolysis by a stronger association with the adenine ring of the 5'-AMP.

  11. Sintesis Metil Ester dari Minyak Biji Kemiri (Aleurites Molluccana Menggunakan Metode Ultrasonokimia

    Directory of Open Access Journals (Sweden)

    Rahmawati Aziz

    2016-01-01

    Full Text Available Using the fuel oil is the basic necessary in the world now. But, the raw material cannot be updated.  To ensure the availability of the fuel oil so, the newest of alternative energy is explored it. One of the ways is biodiesel which made from vegetable oil. In this research is resulted from the transesterification reaction between candlenut oil and methanol by utilizing ultrasonic equipment. This research has passed some phases, they are the determining of acid number in oil then continued by creating biodiesel from ultrasonic wave 47 kHz. Identification of FTIR and GCMS are two methods which used to analyze the component compound in biodiesel product. The conversion number that be gotten from FAME with reaction of variation time 30, 40 and 50 in succession 0,037%, 0,029% and 0,018%. The result analysis of FTIR shows some of functional groups which are special from biodiesel. While the result of GCMS analysis is known that there are 5 component compounds in biodiesel namely ester methyl palmitic acid, ester methyl olead, stearata ester methyl, linoleic ester methyl and elaidic ester methyl.

  12. Composición Esterólica de la Esponja Marina Xestospongia Muta

    Directory of Open Access Journals (Sweden)

    Carmenza Duque

    2009-10-01

    Full Text Available De la esponja marina Xestospongia muta recolectada en la bahía de Santa Marta, Caribe Colombiano, se aislaron por Cromatografía en Columna (CC sobre Silica gel, eluyendo con Benceno: Acetato de Etilo 10:2, dos fracciones esteróiicas; XMl (Rf = 0,28,Si02/Benceno; AcOEt 10:2 y XM2 (Rf = 0,24,SiO2/Benceno : AcOEt 10:2, Los esteróles presentes en estas dos fracciones fueron sometidos a Cromatografía Liquida de Alta Eficiencia (CLAE preparativa y analizados por Cromatografía de Gases (CG y Cromatografía de Gases acoplada en Espectometrla de Masas (CG-EM, Catorce esteróles fueron separados y 13 idenficados. La mayoría de ellos fueron 3n-0H-A^-Esteróles (Aproximadamente el 87% de los esteróles totales incluyendo al (24R + 24S-5,28-Estigmastadien-3i3-24-diol, mezclaepimérica por primera vez asi reportada en la naturaleza. El porcentaje restante correspondió a Estañóles y a un 6,2% de compuestos sin identificar.

  13. Myo-inositol esters of indole-3-acetic acid are endogenous components of Zea mays L. shoot tissue

    Science.gov (United States)

    Chisnell, J. R.

    1984-01-01

    Indole-3-acetyl-myo-inositol esters have been demonstrated to be endogenous components of etiolated Zea mays shoots tissue. This was accomplished by comparison of the putative compounds with authentic, synthetic esters. The properties compared were liquid and gas-liquid chromatographic retention times and the 70-ev mass spectral fragmentation pattern of the pentaacetyl derivative. The amount of indole-3-acetyl-myo-inositol esters in the shoots was determined to be 74 nanomoles per kilogram fresh weight as measured by isotope dilution, accounting for 19% of the ester indole-3-acetic acid of the shoot. This work is the first characterization of an ester conjugate of indole-3-acetate acid from vegetative shoot tissue using multiple chromatographic properties and mass spectral identification. The kernel and the seedling shoot both contain indole-3-acetyl-myo-inositol esters, and these esters comprise approximately the same percentage of the total ester content of the kernel and of the shoot.

  14. Introducing ionic and/or hydrogen bonds into the SAM//Ga2O3 top-interface of Ag(TS)/S(CH2)nT//Ga2O3/EGaIn junctions.

    Science.gov (United States)

    Bowers, Carleen M; Liao, Kung-Ching; Yoon, Hyo Jae; Rappoport, Dmitrij; Baghbanzadeh, Mostafa; Simeone, Felice C; Whitesides, George M

    2014-06-11

    Junctions with the structure Ag(TS)/S(CH2)nT//Ga2O3/EGaIn (where S(CH2)nT is a self-assembled monolayer, SAM, of n-alkanethiolate bearing a terminal functional group T) make it possible to examine the response of rates of charge transport by tunneling to changes in the strength of the interaction between T and Ga2O3. Introducing a series of Lewis acidic/basic functional groups (T = -OH, -SH, -CO2H, -CONH2, and -PO3H) at the terminus of the SAM gave values for the tunneling current density, J(V) in A/cm(2), that were indistinguishable (i.e., differed by less than a factor of 3) from the values observed with n-alkanethiolates of equivalent length. The insensitivity of the rate of tunneling to changes in the terminal functional group implies that replacing weak van der Waals contact interactions with stronger hydrogen- or ionic bonds at the T//Ga2O3 interface does not change the shape (i.e., the height or width) of the tunneling barrier enough to affect rates of charge transport. A comparison of the injection current, J0, for T = -CO2H, and T = -CH2CH3--two groups having similar extended lengths (in Å, or in numbers of non-hydrogen atoms)--suggests that both groups make indistinguishable contributions to the height of the tunneling barrier.

  15. Enzymatic synthesizing of phytosterol oleic esters.

    Science.gov (United States)

    Pan, Xinxin; Chen, Biqiang; Wang, Juan; Zhang, Xinzhi; Zhul, Biyun; Tan, Tianwei

    2012-09-01

    A method of synthesizing the phytosterol esters from oleic acid and sterols was studied, using immobilized lipase Candida sp. 99-125 as catalyst. Molar ratio (oleic acid/phytosterols), temperature, reaction period, organic solvents, catalyst, and silica-gel drier were optimized, and the result showed that 93.4% of the sterols had been esterified under the optimal synthetic condition: the molar ratio of oleic acid/phytosterol is 1:1 in 10 mL iso-octane, immobilized lipase (w, 140% of the sterols), incubated in an orbital shaker (200 rpm) at a temperature of 45 °C for 24 h. The immobilized lipase could be reused for at least 13 times with limited loss of esterification activity. The conversion still maintained up to 86.6%. Hence, this developed process for synthesizing phytosterol esters could be considered as simple and low-energy consumption compared to existing chemical processes.

  16. Quebrando estereótipos e rompendo preconceitos na sala de aula

    Directory of Open Access Journals (Sweden)

    Daniela Jakubaszko

    2015-04-01

    Full Text Available Este texto se preocupa em contribuir para a reflexão que torna possível a identificação e ruptura dos estereótipos sociais que dão origem a preconceitos e ações discriminatórias. Com base nos estudos de Walter Lippann, Agnes Heller, Adam Shaff e Eclea Bosi, pretende-se discutir os conceitos de estereótipo e preconceito, buscando entender o que são e porque se formam. Para entender melhor o estereótipo temos que refletir sobre três elementos que a ele se ligam: a linguagem, o cotidiano e o senso comum. É no plano da linguagem - do diálogo e das práticas de linguagem - que se deve estudar e se pode romper e desconstruir os estereótipos, tomando consciência da própria formação discursiva. O texto oferece, ainda, algumas sugestões para trabalhar o conceito na sala de aula e para ampliar o repertório de textos e referências a serem debatidas com os alunos.

  17. Convenient synthesis of 6-nor-9,10-dihydrolysergic acid methyl ester.

    Science.gov (United States)

    Crider, A M; Grubb, R; Bachmann, K A; Rawat, A K

    1981-12-01

    6-Nor-9,10-dihydrolysergic acid methyl ester (IV) was prepared by demethylation of 9,10-dihydrolysergic acid methyl ester (II) with 2,2,2-trichloroethyl chloroformate, followed by reduction of the intermediate carbamate (III) with zinc in acetic acid. The 6-ethyl-V and 6-n-propyl-VI derivatives were prepared by alkylation of IV with the appropriate halide. All of the ergoline derivatives were evaluated for stereotyped behavior in rats, with 6-nor-6-ethyl-9,10-dihydrolysergic acid methyl ester (V) being active but much less potent than apomorphine. Compound VI was evaluated for its effect on blood pressure; at a dose of 30 mg/kg ip, it significantly lowered, diastolic pressure in normotensive rats.

  18. Valimiskaotuse haavu raviva Rahvaliidu ajutine juht Ester Tuiksoo : "Meil on tugev küünarnukitunne" / Ester Tuiksoo

    Index Scriptorium Estoniae

    Tuiksoo, Ester, 1965-

    2007-01-01

    Ilmunud ka: Severnoje Poberezhje, 28. märts 2007, lk. 2. Delfi lugejate küsimustele vastab Rahvaliidu ajutine juht ja lahkuva valitsuse põllumajandusminister Ester Tuiksoo, kellelt päriti nii erakonna maine taastamise, eesti toidu kui ka jopede jagamise kohta

  19. Synthesis of palm oil fatty acid and trimethylolpropane based ester for biolubricant base stocks

    Science.gov (United States)

    Nor, Nurazira Mohd; Derawi, Darfizzi; Salimon, Jumat

    2018-04-01

    RBD palm oil become one of the interesting renewable resources in biolubricant application. However, palm oil cannot be used directly as lubricant due to some performance limitations such as thermal and oxidative stability. This drawback can be overcome by chemical modification through esterification with polyhydric alcohol such as trimethylolpropane (TMP). The synthesis of ester was carried out via esterification of palm oil fatty acid (POFA) with TMP in the presence of 2% sulphuric acid as catalyst at 150 °C for 5 hours. Gas Chromatography equipped with a Flame Ionization Detector (GC-FID) was used to determine the percentage composition of POTMP ester. The structure confirmation of POTMP ester was proven by Fourier Transformation Infra-Red (FTIR), proton and carbon Nuclear Magnetic Resonance (1H-NMR and 13C-NMR) spectroscopy analysis. The result showed that POTMP ester has successfully synthesized with 97.7% composition of triesters (TE), proved by GC chromatogram. Presence of ester group also evidenced by 1H NMR at 2.27-2.30 ppm and 13C NMR at 173.52-173.54 ppm. The percentage yield of POTMP ester produced was 82% and exist in liquid form at room temperature.

  20. FEL induced molecular operation on cultured fibroblast and cholesterol ester

    International Nuclear Information System (INIS)

    Awazu, Kunio; Ogino, Seiji; Nishimura, Eiichi; Tomimasu, Takio; Yasumoto, Masato.

    1997-01-01

    Free Electron Lasers can be used to molecular operation such as the delivery of a number of molecules into cells or the separation of cholesterol ester. First, cultured NIH3T3 cells are exposed to high-intensity short pulse Free Electron Laser (FEL). The FEL is tuned to an absorption maximum wavelength, 6.1 μm, which was measured by microscopic FTIR. A fluorescence dye in the cell suspension is more absorbed into the cell with the FEL exposure due to the FEL-induced mechanical stress to the cell membrane. A quantitative fluorescence microscopy is used to determine the efficiency of delivery. Second, as a compound in a lipid cell, cholesterol ester was exposed to 5.75 μm FEL. FTIR measurement was done to evaluate the modification of the cholesterol ester. The result showed that the fluorescence intensity of sample cells were higher than that of control cells, and there was significant difference between the control and the sample group. Blebbing and the colony formation of the cells were observed for cells with mechanical stress. As for the cholesterol ester, it can be modified by the FEL irradiation. These results showed that FEL can be used as a molecular operational tool by photo-chemical and photo-mechanical interaction. (author)

  1. Influence of polyacrylic ester and silica fume on the mechanical properties of mortar for repair application

    Directory of Open Access Journals (Sweden)

    Chaohua Jiang

    2016-12-01

    Full Text Available Experimental investigations on the influence of different amounts of polyacrylic ester and silica fumes on the mechanical properties of mortar such as the compressive strength, splitting tensile strength, bonding strength, and abrasion resistance are presented in this article. The results show that the compressive and splitting tensile strength of mortar can be improved with the addition of polyacrylic ester and silica fumes. Results obtained from both the direct tensile bond test and flexural bond test indicate that the addition of polyacrylic ester and silica fumes improves the bond strength significantly, and the enhancement is more obvious with polyacrylic ester paste as interfacial adhesives. Furthermore, mortar incorporation of polyacrylic ester and silica fumes shows superior abrasion resistance compared to the control mortar. Therefore, the correct combination of polyacrylic ester and silica fumes to produce mortars has been shown to have synergistic effects, which results in excellent properties including high bond strength and superior abrasion resistance. Mortars containing polyacrylic ester and silica fumes are ideal for repairing concrete especially for hydraulic concrete structure.

  2. The first N-terminal unprotected (Gly-Aib)n peptide: H-Gly-Aib-Gly-Aib-OtBu.

    Science.gov (United States)

    Gessmann, Renate; Brückner, Hans; Petratos, Kyriacos

    2015-12-01

    Glycine (Gly) is incorporated in roughly half of all known peptaibiotic (nonribosomally biosynthesized antibiotic peptides of fungal origin) sequences and is the residue with the greatest conformational flexibility. The conformational space of Aib (α-aminoisobutyric acid) is severely restricted by the second methyl group attached to the Cα atom. Most of the crystal structures containing Aib are N-terminal protected. Deprotection of the N- or C-terminus of peptides may alter the hydrogen-bonding scheme and/or the structure and may facilitate crystallization. The structure reported here for glycyl-α-aminoisobutyrylglycyl-α-aminoisobutyric acid tert-butyl ester, C16H30N4O5, describes the first N-terminal-unprotected (Gly-Aib)n peptide. The achiral peptide could form an intramolecular hydrogen bond between the C=O group of Gly1 and the N-H group of Aib4. This hydrogen bond is found in all tetrapeptides and N-terminal-protected tripeptides containing Aib, apart from one exception. In the present work, this hydrogen bond is not observed (N...O = 5.88 Å). Instead, every molecule is hydrogen bonded to six other symmetry-related molecules with a total of eight hydrogen bonds per molecule. The backbone conformation starts in the right-handed helical region (and the left-handed helical region for the inverted molecule) and reverses the screw sense in the last two residues.

  3. Palladium-Catalyzed ortho-Olefination of Phenyl Acetic and Phenyl Propylacetic Esters via C-H Bond Activation.

    Science.gov (United States)

    Hu, Jundie; Guan, Mingyu; Han, Jian; Huang, Zhi-Bin; Shi, Da-Qing; Zhao, Yingsheng

    2015-08-21

    A highly regioselective palladium-catalyzed ester-directed ortho-olefination of phenyl acetic and propionic esters with olefins via C-H bond activation has been developed. A wide variety of phenyl acetic and propionic esters were tolerated in this transformation, affording the corresponding olefinated aromatic compounds. The ortho-olefination of heterocyclic acetic and propionic esters also took place smoothly giving the products in good yields, thus proving the potential utility of this protocol in synthetic chemistry.

  4. Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends

    Energy Technology Data Exchange (ETDEWEB)

    Altiparmak, D.; Keskin, A.; Koca, A. [Gazi University, Ankara (Turkey). Technical Education Faculty; Guru, M. [Gazi University, Ankara (Turkey). Engineering and Architectural Faculty

    2007-01-15

    In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load conditions. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO{sub x} emissions increased up to 30% with the new fuel blends. The smoke capacity did not vary significantly. (author)

  5. Alternative fuel properties of tall oil fatty acid methyl ester-diesel fuel blends.

    Science.gov (United States)

    Altiparmak, Duran; Keskin, Ali; Koca, Atilla; Gürü, Metin

    2007-01-01

    In this experimental work, tall oil methyl ester-diesel fuel blends as alternative fuels for diesel engines were studied. Tall oil methyl ester was produced by reacting tall oil fatty acids with methyl alcohol under optimum conditions. The blends of tall oil methyl ester-diesel fuel were tested in a direct injection diesel engine at full load condition. The effects of the new fuel blends on the engine performance and exhaust emission were tested. It was observed that the engine torque and power output with tall oil methyl ester-diesel fuel blends increased up to 6.1% and 5.9%, respectively. It was also seen that CO emissions decreased to 38.9% and NO(x) emissions increased up to 30% with the new fuel blends. The smoke opacity did not vary significantly.

  6. Functionalization of epoxy esters with alcohols as stoichiometric reagents.

    Science.gov (United States)

    Pavlović, Dona; Modec, Barbara; Dolenc, Darko

    2015-01-01

    Glycidyl esters, frequently employed as reactive groups on polymeric supports, were functionalized with alcohols as stoichiometric reagents, yielding β-alkoxyalcohols. Among the solvents studied, best results were obtained in ethers in the presence of a strong proton acid as a catalyst. Alcohols include simple alkanols, diols, protected polyols, 3-butyn-1-ol 3-hydroxypropanenitrile and cholesterol. This protocol represents a convenient way for introduction of various functionalities onto epoxy-functionalized polymers. Under the reaction conditions, some side reactions take place, mostly due to the reactive ester group and water present in the reaction mixture.

  7. Synthesis and Analysis of Methacryloyl-L-Alanine Methyl Ester using fourier Transform Nuclear Magnetic Resonance

    International Nuclear Information System (INIS)

    Tri Darwinto

    2008-01-01

    Methacryloyl-L-alanine methyl ester was synthesized by reacting methacrylic acid with L-alanine methyl ester hydrochloride in triethylamine at temperature of 90 o C. Hydrogel polymer of poly(methacryloyl-L-alanine methyl ester) was much used for diagnosis and therapy of vascular tumor. The molecular structure methacryloyl-L-alanine methyl ester analyzed by fourier transform nuclear magnetic resonance (FT-NMR) for analyzing of carbon atom ( 13 C) using Distortionless Enhancement by Polarization Transfer (DEPT) measurement mode with coupling as well as without coupling from proton atom ( 1 H). Molecular structure analysis result showed that DEPT FT-NMR measurement mode with coupling as well as without coupling from 1 H was very fast, exact and accurate method for molecular analysis of organic compound especially methacryloyl-L-alanine methyl ester. (author)

  8. Scientific opinion: Risks for human health related to the presence of 3- and 2-monochloropropanediol (MCPD), and their fatty acid esters, and glycidyl fatty acid esters in food

    NARCIS (Netherlands)

    Hoogenboom, L.A.P.

    2016-01-01

    EFSA was asked to deliver a scientific opinion on free and esterified 3- and 2-monochloropropane-1,2-diol (MCPD) and glycidyl esters in food. Esters of 3- and 2-MCPD and glycidol are contaminants of processed vegetable oils; free MCPDs are formed in some processed foods. The Panel on Contaminants in

  9. Formation and reduction of 3-monochloropropane-1,2-diol esters in peanut oil during physical refining.

    Science.gov (United States)

    Li, Chang; Li, Linyan; Jia, Hanbing; Wang, Yuting; Shen, Mingyue; Nie, Shaoping; Xie, Mingyong

    2016-05-15

    In the present study, lab-scale physical refining processes were investigated for their effects on the formation of 3-monochloropropane-1,2-diol (3-MCPD) esters. The potential precursors, partial acylglycerols and chlorines were determined before each refining step. 3-MCPD esters were not detected in degummed and bleached oil when the crude oils were extracted by solvent. While in the hot squeezed crude oils, 3-MCPD esters were detected with low amounts. 3-MCPD esters were generated with maximum values in 1-1.5h at a certain deodorizing temperature (220-260°C). Chlorine seemed to be more effective precursor than partial acylglycerol. By washing bleached oil before deodorization with ethanol solution, the precursors were removed partially and the content of 3-MCPD esters decreased to some extent accordingly. Diacetin was found to reduce 3-MCPD esters effectively. Copyright © 2015 Elsevier Ltd. All rights reserved.

  10. Highly efficient synthetic method onpyroacm resin using the boc SPPS protocol for C-terminal cysteine peptide synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Juvekar, Vinayak; Kim, Kang Tae; Gong, Young Dae [Innovative Drug Library Research Center, Dept. of Chemistry, College of Science, Dongguk University, Seoul (Korea, Republic of)

    2017-01-15

    A very effective process on Pyroacm resin was developed for solid-phase peptide synthesis (SPPS) of C-terminal cysteine and cysteine ester peptides. The process uses cysteine side chain anchoring to the Pyroacm resin and the Boc protocol for SPPS. The Pyroacm resin showed remarkable stability under standard trifluoromethanesulfonic acid (TFMSA) cleavage condition. TFMSA cleavage of protecting groups generates a peptide-linked resin, which can be subjected to peptide modification reactions. Finally, the peptide can be cleaved from the resin using methoxycarbonylsulfenyl chloride. The utility of this protocol was demonstrated by its applications to the synthesis of model peptides, key intermediates in the preparation of natural products riparin 1.2 and a-factor.

  11. Degradation of Jatropha curcas phorbol esters derived from Jatropha oil cake and their tumor-promoting activity.

    Science.gov (United States)

    Nakao, Motoyuki; Hasegawa, Go; Yasuhara, Tadashi; Ishihara, Yoko

    2015-04-01

    Large amount of oil cake is generated during biodiesel production from Jatropha seeds. Although Jatropha oil cake is rich in plant nutrients, presence of toxic phorbol esters restricts the usage of oil cake as a fertilizer. The objective of this study is to evaluate the components and tumor promoting activity of phorbol esters in Jatropha oil cake-supplemented soil and plants grown in the treated soil. Contents and their biological activity of Jatropha phorbol esters in soil and plants were sequentially analyzed by high-performance liquid chromatography (HPLC) and in vitro cell transformation assay, respectively. Disappearance of Jatropha phorbol-ester-specific peaks were followed with HPLC during incubation of Jatropha oil cake with soil for five weeks. Along with the degradation of Jatropha phorbol ester in soil, tumor-promoting activity in the sample was also attenuated and ultimately disappeared. Jatropha phorbol esters and tumor promoting activity were not detected from mustard spinach grown in the Jatropha oil cake-supplemented soil. In addition, the esterase KM109 degrades DHPB (see definition below; Jatropha phorbol ester) and reduced its tumor-promoting activity. From these data, we conclude: (1) components and tumor promoting activity of Jatropha phorbol esters in the oil cake disappeared completely by incubation with soil for five-week, (2) Jatropha phorbol esters did not transfer into plants grown in the Jatropha oil cake-supplemented soil, and (3) DHPB can be degraded by esterase from soil bacterium. These observations are useful for utilization of Jatropha oil cake as a fertilizer. Copyright © 2014 Elsevier Inc. All rights reserved.

  12. Other factors to consider in the formation of chloropropandiol fatty esters in oil processes.

    Science.gov (United States)

    Ramli, Muhamad Roddy; Siew, Wai Lin; Ibrahim, Nuzul Amri; Kuntom, Ainie; Abd Razak, Raznim Arni

    2015-01-01

    This paper examines the processing steps of extracting palm oil from fresh fruit bunches in a way that may impact on the formation of chloropropandiol fatty esters (3-MCPD esters), particularly during refining. Diacylglycerols (DAGs) do not appear to be a critical factor when crude palm oils are extracted from various qualities of fruit bunches. Highly hydrolysed oils, in spite of the high free fatty acid (FFA) contents, did not show exceptionally high DAGs, and the oils did not display a higher formation of 3-MCPD esters upon heat treatment. However, acidity measured in terms of pH appears to have a strong impact on 3-MCPD ester formation in the crude oil when heated at high temperatures. The differences in the extraction process of crude palm oil from current commercial processes and that from a modified experimental process showed clearly the effect of acidity of the oil on the formation of 3-MCPD esters. This paper concludes that the washing or dilution step in palm oil mills removes the acidity of the vegetative materials and that a well-optimised dilution/washing step in the extraction process will play an important role in reducing formation of 3-MCPD esters in crude palm oil upon further heat processing.

  13. Antioxidants Inhibit Formation of 3-Monochloropropane-1,2-diol Esters in Model Reactions.

    Science.gov (United States)

    Li, Chang; Jia, Hanbing; Shen, Mingyue; Wang, Yuting; Nie, Shaoping; Chen, Yi; Zhou, Yongqiang; Wang, Yuanxing; Xie, Mingyong

    2015-11-11

    The capacities of six antioxidants to inhibit the formation of 3-monochloropropane-1,2 diol (3-MCPD) esters were examined in this study. Inhibitory capacities of the antioxidants were investigated both in chemical models containing the precursors (tripalmitoyl glycerol, 1,2-dipalmitoyl-sn-glycerol, monopalmitoyl glycerol, and sodium chloride) of 3-MCPD esters and in oil models (rapeseed oil and sodium chloride). Six antioxidants, butylated hydroxytoluene (BHT), butylated hydroxy anisole (BHA), tert-butyl hydroquinone (TBHQ), propyl gallate (PG), L-ascorbyl palmitate (AP), and α-tocopherol (VE), were found to exhibit inhibiting capacities on 3-MCPD ester formation both in chemical models and in oil models. TBHQ provided the highest inhibitory capacity both in chemical models and in oil models; 44% of 3-MCPD ester formation was inhibited in the presence of TBHQ (66 mg/kg of oil) after heating of rapeseed oil at 230 °C for 30 min, followed by PG and AP. BHT, BHA, and VE appeared to have weaker inhibitory abilities in both models. VE exhibited the lowest inhibition rate; 22% of 3-MCPD esters were inhibited in the presence of VE (172 mg/kg of oil) after heating of rapeseed oil at 230 °C for 30 min. In addition, the inhibition rates of PG and VE decreased dramatically with an increase in temperature or heating time. The results suggested that some antioxidants, such as TBHQ, PG, and AP, could be the potential inhibitors of 3-MCPD esters in practice.

  14. Biodegradation tests of mercaptocarboxylic acids, their esters, related divalent sulfur compounds and mercaptans.

    Science.gov (United States)

    Rücker, Christoph; Mahmoud, Waleed M M; Schwartz, Dirk; Kümmerer, Klaus

    2018-04-17

    Mercaptocarboxylic acids and their esters, a class of difunctional compounds bearing both a mercapto and a carboxylic acid or ester functional group, are industrial chemicals of potential environmental concern. Biodegradation of such compounds was systematically investigated here, both by literature search and by experiments (Closed Bottle Test OECD 301D and Manometric Respirometry Test OECD 301F). These compounds were found either readily biodegradable or at least biodegradable to a significant extent. Some related compounds of divalent sulfur were tested for comparison (mercaptans, sulfides, disulfides). For the two relevant monofunctional compound classes, carboxylic acids/esters and mercaptans, literature data were compiled, and by comparison with structurally similar compounds without these functional groups, the influence of COOH/COOR' and SH groups on biodegradability was evaluated. Thereby, an existing rule of thumb for biodegradation of carboxylic acids/esters was supported by experimental data, and a rule of thumb could be formulated for mercaptans. Concurrent to biodegradation, abiotic processes were observed in the experiments, rapid oxidative formation of disulfides (dimerisation of monomercaptans and cyclisation of dimercaptans) and hydrolysis of esters. Some problems that compromise the reproducibility of biodegradation test results were discussed.

  15. Investigations on the transport and metabolism of high density lipoprotein cholesteryl esters in African green monkeys

    International Nuclear Information System (INIS)

    Sorci-Thomas, M.G.

    1984-01-01

    The metabolic fate of circulating high density lipoprotein cholesteryl esters was studied in African green monkeys to determine the significance of the lipid transfer reaction on the catabolism of lipoprotein cholesteryl esters. A method of doubly labeling both moieties of lipoprotein cholesteryl esters with [ 3 He]cholesteryl oleate and cholesteryl [ 14 C]oleate was developed for the purpose of studying plasma cholesteryl ester metabolism in vivo. In these studies the total plasma [ 3 He]cholesterol turnover resulted in production rates, which ranged from 10-17 mg/kg day, similar to previously reported values in African green monkeys and in normal lipoproteinemic humans. In contrast to the production rates calculated from the decay of plasma 3 He-radioactivity, the production rates calculated from lipoproteins labeled with cholesteryl [ 14 C]oleate were approximately 2-3 times greater. In addition to these studies, a plasma cholesteryl ester transacylation activity was demonstrated in vitro when HDL containing doubly labeled cholesteryl esters were incubated with fresh plasma. These results demonstrated that high density lipoprotein cholesteryl esters undergo transacylation in vitro, resulting in release and reesterification of free [ 3 H]cholesterol

  16. Transesterification Synthesis of Chloramphenicol Esters with the Lipase from Bacillus amyloliquefaciens

    Directory of Open Access Journals (Sweden)

    Fengying Dong

    2017-09-01

    Full Text Available This work presents a synthetic route to produce chloramphenicol esters by taking advantage the high enantio- and regio-selectivity of lipases. A series of chloramphenicol esters were synthesized using chloramphenicol, acyl donors of different carbon chain length and lipase LipBA (lipase cloned from Bacillus amyloliquefaciens. Among acyl donors with different carbon chain lengths, vinyl propionate was found to be the best. The influences of different organic solvents, reaction temperature, reaction time, enzyme loading and water content on the synthesis of the chloramphenicol esters were studied. The synthesis of chloramphenicol propionate (0.25 M with 4.0 g L−1 of LipBA loading gave a conversion of ~98% and a purity of ~99% within 8 h at 50 °C in 1,4-dioxane as solvent. The optimum mole ratio of vinyl propionate to chloramphenicol was increased to 5:1. This is the first report of B. amyloliquefaciens lipase being used in chloramphenicol ester synthesis and a detailed study of the synthesis of chloramphenicol propionate using this reaction. The high enzyme activity and selectivity make lipase LipBA an attractive catalyst for green chemical synthesis of molecules with complex structures.

  17. Liquid chromatographic analysis of a formulated ester from a gas-turbine engine test

    Science.gov (United States)

    Jones, W. R., Jr.; Morales, W.

    1983-01-01

    Size exclusion chromatography (SEC) utilizing mu-Bondagel and mu-Styragel columns with a tetrahydrofuran mobile phase was used to determine the chemical degradation of lubricant samples from a gas-turbine engine test. A MIL-L-27502 candidate, ester-based lubricant was run in a J57-29 engine at a bulk oil temperature of 216 C. In general, the analyses indicated a progressive loss of primary ester, additive depletion, and formation of higher molecular weight material. An oil sample taken at the conclusion of the test showed a reversal of this trend because of large additions of new oil. The high-molecular-weight product from the degraded ester absorbed strongly in the ultraviolet region at 254 nanometers. This would indicate the presence of chromophoric groups. An analysis of a similar ester lubricant from a separate high-temperature bearing test yielded qualitatively similar results.

  18. Fully convergent chemical synthesis of ester insulin: determination of the high resolution X-ray structure by racemic protein crystallography.

    Science.gov (United States)

    Avital-Shmilovici, Michal; Mandal, Kalyaneswar; Gates, Zachary P; Phillips, Nelson B; Weiss, Michael A; Kent, Stephen B H

    2013-02-27

    Efficient total synthesis of insulin is important to enable the application of medicinal chemistry to the optimization of the properties of this important protein molecule. Recently we described "ester insulin"--a novel form of insulin in which the function of the 35 residue C-peptide of proinsulin is replaced by a single covalent bond--as a key intermediate for the efficient total synthesis of insulin. Here we describe a fully convergent synthetic route to the ester insulin molecule from three unprotected peptide segments of approximately equal size. The synthetic ester insulin polypeptide chain folded much more rapidly than proinsulin, and at physiological pH. Both the D-protein and L-protein enantiomers of monomeric DKP ester insulin (i.e., [Asp(B10), Lys(B28), Pro(B29)]ester insulin) were prepared by total chemical synthesis. The atomic structure of the synthetic ester insulin molecule was determined by racemic protein X-ray crystallography to a resolution of 1.6 Å. Diffraction quality crystals were readily obtained from the racemic mixture of {D-DKP ester insulin + L-DKP ester insulin}, whereas crystals were not obtained from the L-ester insulin alone even after extensive trials. Both the D-protein and L-protein enantiomers of monomeric DKP ester insulin were assayed for receptor binding and in diabetic rats, before and after conversion by saponification to the corresponding DKP insulin enantiomers. L-DKP ester insulin bound weakly to the insulin receptor, while synthetic L-DKP insulin derived from the L-DKP ester insulin intermediate was fully active in binding to the insulin receptor. The D- and L-DKP ester insulins and D-DKP insulin were inactive in lowering blood glucose in diabetic rats, while synthetic L-DKP insulin was fully active in this biological assay. The structural basis of the lack of biological activity of ester insulin is discussed.

  19. Microalgal fatty acid methyl ester a new source of bioactive compounds with antimicrobial activity

    Directory of Open Access Journals (Sweden)

    Arumugham Suresh

    2014-09-01

    Full Text Available Objective: To evaluate fatty acid composition and the antimicrobial activity of the major fraction of fatty acid methyl ester (FAME extracts from three microalgae collected from freshwater lakes in Theni District, Tamil Nadu, India. Methods: Antimicrobial study was carried out by well diffusion method against bacterial as well as fungal pathogens such as Escherichia coli, Staphylococcus aureus, Enterobacter sp., Klebsiella sp., Salmonella typhi, Fusarium sp., Cryptococcus sp., Candida sp., and Aspergillus niger and Aspergillus flavus. The FAME profiles were determined through gas chromatography with a flame ionization detector. Results: The FAME was found to be radial effective in inhibiting the radial growth of both bacterial and fungal pathogens. The FAME extracts exhibited the antibacterial activity against three clinical pathogens, namely, Escherichia coli, Salmonella typhi and Enterobacter sp. with the maximum zone of inhibition of 12.0 mm, 12.0 mm and 11.0 mm, respectively. The FAME showed moderate antifungal activity against Cryptococcus sp. (11.8 mm, Aspergillus niger (10.5 mm, Candida sp. (11.8 mm and Fusarium sp. (10.4 mm. Gas chromatography-flame ionization detector analysis revealed about 30 different FAMEs. Conclusions: We assume that the observed antimicrobial potency may be due to the abundance of erucic acid methyl ester (C22:0, arachidic acid methyl ester (C20:0, palmitic acid methyl ester (C16:0, cis-11-eicosenoicmethyl ester (C20:1, cis-11, 14-eicosadienoic acid methyl ester (C20:2 and linolenic acid methyl ester (C18:3 in FAMEs which appears to be promising to treat microbial diseases.

  20. Fatty acid methyl esters production: chemical process variables

    Directory of Open Access Journals (Sweden)

    Paulo César Narváez Rincón

    2004-05-01

    Full Text Available The advantages of fatty acid methyl esters as basic oleochemicals over fatty acids, the seventies world energy crisis and the use of those oleochemicals as fuels, have increased research interest on fats and oils trans-esterification. In this document, a review about basic aspects, uses, process variables and problems associated to the production process of fatty acid methyl esters is presented. A global view of recent researches, most of them focused in finding a new catalyst with same activity as the alcohol-soluble hydroxides (NaOH, KOH, and suitable to be used in transforming fats and oils with high levels of free fatty acids and water avoiding separation problems and reducing process costs, is also discussed.

  1. Mechanical strength of various cyanate ester/epoxy insulation systems after reactor irradiation

    International Nuclear Information System (INIS)

    Prokopec, R.; Humer, K.; Maix, R.K.; Fillunger, H.; Weber, H.W.

    2006-01-01

    In order to ensure safety operation of the magnet coils, the insulation system must keep its mechanical strength over the whole magnet lifetime under the appropriate radiation environment. Recent results on cyanate ester/epoxy blends demonstrated their mechanical integrity after irradiation to the ITER design fluence level, i.e. 1 x 10 22 m -2 (E > 0.1 MeV). For economic reasons, the cyanate ester content in the blend should be kept as low as possible due to the higher price compared to traditional epoxy resins. Therefore, the optimal composition of cyanate ester and epoxy in the blend is of great importance. In this study R-glass fiber/ Kapton reinforced cyanate ester based blends using different epoxy resins and epoxy contents were investigated. Short-beam shear as well as static tensile tests were carried out at 77 K prior to and after irradiation to a fast neutron fluence of 1 and 2 x 10 22 m -2 (E > 0.1 MeV) in the TRIGA reactor (Vienna) at ambient temperature (340 K). In addition, tension-tension fatigue measurements were performed in the load and the strain controlled mode in order to simulate the pulsed operation conditions of the ITER magnets. Initial results show, that cyanate ester contents of both 40 % and 30 % lead only to a small reduction of the mechanical strength after irradiation to the ITER design fluence. (author)

  2. Effect of rapeseed oil derived plant sterol and stanol esters on atherosclerosis parameters in cholesterol challenged heterozygous Watanabe Heritable Hyperlipidemic rabbits

    DEFF Research Database (Denmark)

    Schrøder, Malene; Fricke, Christiane; Pilegaard, Kirsten

    2009-01-01

    Watanabe heritable hyperlipidaemic (Hh-WHHL) rabbits. Four groups (n 18 per group) received a cholesterol-added (2 g/kg) standard chow or this diet with added RSO stanol esters (17 g/kg), RSO stanol esters (34 g/kg) or RSO sterol esters (34 g/kg) for 18 weeks. Feeding RSO stanol esters increased plasma...... campestanol (P Feeding RSO sterol esters increased concentrations of plasma campesterol (P ... of the RSO stanol ester groups and in one in the RSO sterol ester group. Aortic cholesterol was decreased in the treated groups (P response to lowering of plasma cholesterol induced by RSO sterol and stanol esters. In conclusion, RSO stanol and sterol esters with a high concentration...

  3. Presidendiauto jalakäijate teel / Ester Shank

    Index Scriptorium Estoniae

    Šank, Ester, 1956-

    2003-01-01

    Presidendi pressinõunik Ester Shank selgitab, miks president Arnold Rüütel sõitis eskorauto saatel lauluväljakule Andrea Bocelli ja Annely Peebo kontserdile läbi Kadrioru pargi jalakäijate teed mööda

  4. Chromatographic, Spectrometric and NMR Characterization of a New Set of Glucuronic Acid Esters Synthesized by Lipase

    Directory of Open Access Journals (Sweden)

    Michel Marlier

    2007-01-01

    Full Text Available An enzymatic synthesis was developed on a new set of D-glucuronic acid esters and particularly the tetradecyl-D-glucopyranosiduronate also named tetradecyl D-glucuronate. Chromatographic analyses revealed the presence of the ester as a mixture of anomeric forms for carbon chain lengths superior to 12. TOF/MS and MS/MS studies confirmed the synthesis of glucuronic acid ester. The NMR study also confirmed the structure of glucuronic acid esters and clearly revealed an anomeric (α/β ratio equivalent to 3/2

  5. Occurrence of 3-MCPD and glycidyl esters in edible oils in the United States.

    Science.gov (United States)

    MacMahon, Shaun; Begley, Timothy H; Diachenko, Gregory W

    2013-01-01

    Fatty acid esters of 3-monochloropropanediol (3-MCPD) and glycidol are processing contaminants found in a wide range of edible oils. While both 3 MCPD and glycidol have toxicological properties that at present has concerns for food safety, the published occurrence data are limited. Occurrence information is presented for the concentrations of 3-MCPD and glycidyl esters in 116 retail and/or industrial edible oils and fats using LC-MS/MS analysis of intact esters. The concentrations for bound 3-MCPD ranged from below the limit of quantitation (3-MCPD and glycidol were seen in refined palm oil and palm olein samples. Palm olein samples also contained a higher percentage of 3-MCPD in mono-ester form than any other type of oil.

  6. Pyrimidine and nucleoside gamma-esters of L-Glu-Sar

    DEFF Research Database (Denmark)

    Eriksson, André H; Elm, Peter L; Begtrup, Mikael

    2005-01-01

    -tetrahydrofuran-3-yl ester)-Sar (I), l-Glu(thymine-1-yl-methyl ester)-Sar (II) and l-Glu(acyclothymidine)-Sar (III) were synthesised and in vitro stability was studied in various aqueous and biological media. Affinity to and translocation via hPEPT1 was investigated in mature Caco-2 cell monolayers, grown......The aim of the present study was to improve the synthetic pathway of bioreversible dipeptide derivatives as well as evaluate the potential of using l-Glu-Sar as a pro-moiety for delivering three newly synthesised nucleoside and pyrimidine l-Glu-Sar derivatives. l-Glu(trans-2-thymine-1-yl...

  7. Atmospheric oxidation of selected alcohols and esters

    Energy Technology Data Exchange (ETDEWEB)

    Becker, K H; Cavalli, F

    2001-03-01

    The decision whether it is appropriate and beneficial for the environment to deploy specific oxygenated organic compounds as replacements for traditional solvent types requires a quantitative assessment of their potential atmospheric impacts including tropospheric ozone and other photooxidant formation. This involves developing chemical mechanisms for the gasphase atmospheric oxidation of the compounds which can be reliably used in models to predict their atmospheric reactivity under a variety of environmental conditions. Until this study, there was very little information available concerning the atmospheric fate of alcohols and esters. The objectives of this study were to measure the atmospheric reaction rates and to define atmospheric reaction mechanisms for the following selected oxygenated volatile organic compounds: the alcohols, 1-butanol and 1-pentanol, and the esters, methyl propionate and dimethyl succinate. The study has successfully addressed these objectives. (orig.)

  8. Degradation Mechanisms of Poly(ester urethane) Elastomer

    Energy Technology Data Exchange (ETDEWEB)

    Edgar, Alexander S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2017-11-30

    This report describes literature regarding the degradation mechanisms associated with a poly(ester urethane) block copolymer, Estane® 5703 (Estane), used in conjunction with Nitroplasticizer (NP), and 1,3,5,7-tetranitro-1,3,5,7-tetrazocane, also known as high molecular weight explosive (HMX) to produce polymer bonded explosive PBX 9501. Two principal degradation mechanisms are reported: NO2 oxidative reaction with the urethane linkage resulting in crosslinking and chain scission events, and acid catalyzed hydrolysis of the ester linkage. This report details future work regarding this PBX support system, to be conducted in late 2017 and 2018 at Engineered Materials Group (MST-7), Materials Science and Technology Division, Los Alamos National Laboratory. This is the first of a series of three reports on the degradation processes and trends of the support materials of PBX 9501.

  9. Synthesis and Biological Evaluation of Liguzinediol Mono- and Dual Ester Prodrugs as Promising Inotropic Agents

    Directory of Open Access Journals (Sweden)

    Jing Zhang

    2014-11-01

    Full Text Available The potent positive inotropic effect, together with the relatively low safety risk of liguzinediol (LZDO, relative to currently available inotropic drugs, has prompted us to intensively research and develop LZDO as a potent positive inotropic agent. In this study, to obtain LZDO alternatives for oral chronic administration, a series of long-chain fatty carboxylic mono- and dual-esters of LZDO were synthesized, and preliminarily evaluated for physicochemical properties and bioconversion. Enhanced lipophilic properties and decreased solubility of the prodrugs were observed as the side chain length increased. All esters showed conspicuous chemical stability in phosphate buffer (pH 7.4. Moreover, the enzymatic hydrolysis of esters in human plasma and human liver microsomes confirmed that the majority of esters were converted to LZDO, with release profiles that varied due to the size and structure of the side chain. In vivo pharmacokinetic studies following oral administration of monopivaloyl (M5, monodecyl (M10 and monododecyl (M12 esters demonstrated the evidently extended half-lives relative to LZDO dosed alone. In particular the monopivaloyl ester M5 exhibited an optimal pharmacokinetic profile with appropriate physiochemical characteristics.

  10. Aspergillus niger whole-cell catalyzed synthesis of caffeic acid phenethyl ester in ionic liquids.

    Science.gov (United States)

    Rajapriya, Govindaraju; Morya, Vivek Kumar; Mai, Ngoc Lan; Koo, Yoon-Mo

    2018-04-01

    Synthesis of caffeic acid ester essentially requires an efficient esterification process to produce various kinds of medicinally important ester derivatives. In the present study, a comprehensive and comparative analysis of whole-cell catalyzed caffeic acid esters production in ionic liquids (ILs) media was performed. Olive oil induced mycelial mass of halotolerant Aspergillus niger (A.niger) EXF 4321 was freeze dried and used as a catalyst. To ensure maximum solubilization of caffeic acid for highest substrate loading several ILs were screened and 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Emim][Tf 2 N]) was found to have the maximum solubility and favoured for enzymatic activity of freeze dried mycelia. The whole-cell catalyzed synthesis of caffeic acid phenethyl ester (CAPE) conditions were optimized and bioconversion up to 84% was achieved at a substrate molar ratio of 1:20 (caffeic acid:2-phenyl ethanol), 30°C for 12h. Results obtained during this study were encouraging and helpful to design a bioreactor system to produce caffeic acid derived esters. Copyright © 2017 Elsevier Inc. All rights reserved.

  11. Rapid screening of fatty acid alkyl esters in olive oils by time domain reflectometry.

    Science.gov (United States)

    Berardinelli, Annachiara; Ragni, Luigi; Bendini, Alessandra; Valli, Enrico; Conte, Lanfranco; Guarnieri, Adriano; Toschi, Tullia Gallina

    2013-11-20

    The main aim of the present research is to assess the possibility of quickly screening fatty acid alkyl esters (FAAE) in olive oils using time domain reflectometry (TDR) and partial least-squares (PLS) multivariate statistical analysis. Eighteen virgin olive oil samples with fatty acid alkyl ester contents and fatty acid ethyl ester/methyl ester ratios (FAEE/FAME) ranging from 3 to 100 mg kg(-1) and from 0.3 to 2.6, respectively, were submitted to tests with time domain resolution of 1 ps. The results obtained in test set validation demonstrated that this new and fast analytical approach is able to predict FAME, FAEE, and FAME + FAEE contents with R(2) values of 0.905, 0.923, and 0.927, respectively. Further measurements on mixtures between olive oil and FAAE standards confirmed that the prediction is based on a direct influence of fatty acid alkyl esters on the TDR signal. The suggested technique appeared potentially suitable for monitoring one of the most important quality attribute of the olive oil in the extraction process.

  12. Differential Partitioning of Triterpenes and Triterpene Esters in Apple Peel.

    Science.gov (United States)

    Poirier, Brenton C; Buchanan, David A; Rudell, David R; Mattheis, James P

    2018-02-28

    Apple peel is a rich source of secondary metabolites, and several studies have outlined the dietary health benefits of ursane-type triterpenes in apple. Changes in triterpene metabolism have also been associated with the development of superficial scald, a postharvest apple peel browning disorder, and postharvest applications of diphenylamine and 1-methylcyclopropene. Previously, studies have generated metabolite profiles for whole apple peel or apple wax. In this study, we report separate metabolic analyses of isolated wax fractions and peel epidermis to investigate the spatial distribution of secondary metabolites in peel. In addition to examining previously reported triterpenes, we identified several unreported fatty acid esters of ursane-type triterpenes (C14-C22). All free pentacyclic triterpenes and triterpenic acids, with the exception of β-amyrin, were localized in the wax layer, along with esters of ursolic acid and uvaol. All sterols, sterol derivatives and α-amyrin esters were localized in the dewaxed peel epidermis.

  13. CFD simulation of fatty acid methyl ester production in bubble column reactor

    Science.gov (United States)

    Salleh, N. S. Mohd; Nasir, N. F.

    2017-09-01

    Non-catalytic transesterification is one of the method that was used to produce the fatty acid methyl ester (FAME) by blowing superheated methanol bubbles continuously into the vegetable oil without using any catalyst. This research aimed to simulate the production of FAME from palm oil in a bubble column reactor. Computational Fluid Dynamic (CFD) simulation was used to predict the distribution of fatty acid methyl ester and other product in the reactor. The fluid flow and component of concentration along the reaction time was investigated and the effects of reaction temperature (523 K and 563 K) on the non-catalytic transesterification process has been examined. The study was carried out using ANSYS CFX 17.1. The finding from the study shows that increasing the temperature leads to higher amount of fatty acid methyl ester can be produced in shorter time. On the other hand, concentration of the component such as triglyceride (TG), glycerol (GL) and fatty acid methyl ester (FAME) can be known when reaching the optimum condition.

  14. Mitigation of 3-Monochloro-1,2-propanediol Ester Formation by Radical Scavengers.

    Science.gov (United States)

    Zhang, Hai; Jin, Pengwei; Zhang, Min; Cheong, Ling-Zhi; Hu, Peng; Zhao, Yue; Yu, Liangli; Wang, Yong; Jiang, Yuanrong; Xu, Xuebing

    2016-07-27

    The present study investigated the possible mechanism of free radical scavengers on mitigation of 3-monochloro-1,2-propanediol (3-MCPD) fatty acid ester formation in vegetable oils. The electron spin resonance investigation showed that the concentration of free radicals could be clearly decreased in 1,2-distearoyl-sn-glycerol (DSG) samples by all four antioxidants (l-ascorbyl palmitate, α-tocopherol, lipophilic tea polyphenols, and rosemary extract) at 120 °C for 20 min under a N2 atmosphere. Moreover, the rosemary extract exhibited the highest inhibition efficiency. The Fourier transform infrared spectroscopy examination of DSG with α-tocopherol at 25 and 120 °C revealed that α-tocopherol could prevent the involvement of an ester carbonyl group of DSG in forming the cyclic acyloxonium free radical intermediate. Furthermore, the ultraperformance liquid chromatography-quadrupole-time-of-flight mass spectrometry analysis showed that α-tocopherol could suppress the formation of 3-MCPD di- and monoesters. Finally, the four antioxidants could decrease 3-MCPD esters in the palm oil during deodorization. Particularly, the rosemary extract also showed the highest efficiency in 3-MCPD ester mitigation.

  15. Plasma application for detoxification of Jatropha phorbol esters

    International Nuclear Information System (INIS)

    Kongmany, S; Matsuura, H; Furuta, M; Okuda, S; Imamura, K; Maeda, Y

    2013-01-01

    Atmospheric pressure non-thermal dielectric barrier discharge (DBD) plasma generated by helium gas at high voltage and input power of about 50 W was first applied to detoxification of Jatropha curcas phorbol esters (J. PEs) as well as standard phorbol ester (4β-12-O-tetradecanoyl phorbol-13-acetate, TPA) in water and methanol. Plasma irradiation on the solution sample was conducted for 15 min. In aqueous solution, only 16% of TPA was degraded and complete degradation of J. PEs was observed. On the contrary, complete degradation of both TPA and J. PEs in methanol was achieved by the same plasma irradiation condition. Hydroxyl radical (.OH) generated by plasma irradiation of the solution is expected as the main radical inducing the degradation of PEs.

  16. Carboxylesterase-dependent cytotoxicity of dibasic esters (DBE) in rat nasal explants.

    Science.gov (United States)

    Trela, B A; Bogdanffy, M S

    1991-02-01

    Dibasic esters (DBE) are a solvent mixture of dimethyl adipate (DMA), dimethyl glutarate (DMG), and dimethyl succinate (DMS) used in the paint and coating industry. Subchronic inhalation toxicity studies have demonstrated that DBE induce a mild degeneration of the olfactory, but not the respiratory, epithelium of the rat nasal cavity. Carboxylesterase-mediated hydrolysis of the individual dibasic esters is more efficient in olfactory than in respiratory mucosal homogenates. In the present study, an in vitro system of cultured rat nasal explants was utilized to determine if DBE toxicity is dependent on a metabolic activation by nonspecific carboxylesterase. Explants from both the olfactory and the respiratory regions of the female rat nasal cavity were incubated for 2 hr in Williams' medium E containing 10-100 mM DMA, DMG, or DMS. DBE caused a dose-related increase in nasal explant acid phosphatase release, a biochemical index of cytotoxicity. HPLC analysis demonstrated parallel increases in the carboxylesterase-mediated formation of monomethyl ester metabolites. Diacid metabolite production in the nasal explant system was not entirely concentration-dependent. Metabolite concentrations and acid phosphatase release were generally greater in olfactory than respiratory tissues. DBE-induced cytotoxicity and acid metabolite production were markedly attenuated in nasal tissue excised from rats which were pretreated with bis(p-nitrophenyl)phosphate, a carboxylesterase inhibitor. This study presents a viable in vitro method for assessing organic ester cytotoxicity in the rat nasal cavity. It was shown that DBE are weak nasal toxicants under the conditions of this system. It was further demonstrated that DBE toxicity is dependent on a carboxylesterase-mediated activation. A similar mechanism was proposed for the nasal toxicity induced by other organic esters following inhalation exposure.

  17. Mono- and tri-ester hydrogenolysis using tandem catalysis. Scope and mechanism.

    Energy Technology Data Exchange (ETDEWEB)

    Lohr, Tracy L.; Li, Zhi; Assary, Rajeev S.; Curtiss, Larry A.; Marks, Tobin J.

    2016-01-01

    The scope and mechanism of thermodynamically leveraged ester RC(O)O-R' bond hydrogenolysis by tandem metal triflate + supported Pd catalysts are investigated both experimentally and theoretically by DFT and energy span analysis. This catalytic system has a broad scope, with relative cleavage rates scaling as, tertiary 4 secondary 4 primary ester at 1 bar H-2, yielding alkanes and carboxylic acids with high conversion and selectivity. Benzylic and allylic esters display the highest activity. The rate law is nu = k[M(OTf )(n)](1)[ester](0)[H-2](0) with an H/D kinetic isotope effect = 6.5 +/- 0.5, implying turnover-limiting C-H scission following C-O cleavage, in agreement with theory. Intermediate alkene products are then rapidly hydrogenated. Applying this approach with the very active Hf(OTf)(4) catalyst to bio-derived triglycerides affords near-quantitative yields of C-3 hydrocarbons rather than glycerol. From model substrates, it is found that RC(O)O-R' cleavage rates are very sensitive to steric congestion and metal triflate identity. For triglycerides, primary/external glyceryl CH2-O cleavage predominates over secondary/internal CH-O cleavage, with the latter favored by less acidic or smaller ionic radius metal triflates, raising the diester selectivity to as high as 48% with Ce(OTf)(3).

  18. Scientific opinion on the risks for human health related to the presence of 3-and 2-monochloropropanediol (MCPD), and their fatty acid esters, and glycidyl fatty acid esters in food

    DEFF Research Database (Denmark)

    Petersen, Annette

    EFSA was asked to deliver a scientific opinion on free and esterified 3- and 2-monochloropropane-1, 2-diol (MCPD) and glycidyl esters in food. Esters of 3- and 2-MCPD and glycidol are contaminants of processed vegetable oils; free MCPDs are formed in some processed foods. The Panel on Contaminant...

  19. Thermal studies of poly(esters) containing silicon or germanium in the main chain

    International Nuclear Information System (INIS)

    Tagle, L.H.; Terraza, C.; Valenzuela, P.; Leiva, A.; Urzua, M.

    2005-01-01

    The thermal properties of poly(esters) containing Si and/or Ge in the main chain derived from the acid dichlorides bis(4-chloroformyl-phenyl)-dimethyl-silane, bis(4-chloroformyl-phenyl)-dimethyl-germane, bis(4-chloroformyl-phenyl)-diphenyl-silane and bis(4-chloroformyl-phenyl)-diphenyl-silane, and the diphenols bis(4-hydroxyphenyl)-dimethyl-silane, bis(4-hydroxyphenyl)-dimethyl-germane, bis(4-hydroxyphenyl)-diphenyl-silane and bis(4-hydroxyphenyl)-diphenyl-germane were studied by differential scanning calorimetry and dynamic thermogravimetry. Poly(esters) with two Si atoms in the main chain showed higher values of T g than those with two Ge atoms, and the same was observed for poly(esters) with phenyl groups bonded to the heteroatoms, instead of those with methyl groups. Thermal decomposition temperatures were also higher for those poly(esters) with two Si atoms in the main chain and those in which the heteroatom is bonded to phenyl groups, due to the higher polarity of the Si-C bond in front of the Ge-C

  20. Apomorphine and its esters

    DEFF Research Database (Denmark)

    Borkar, Nrupa; Chen, Zhizhong; Saaby, Lasse

    2016-01-01

    Oral delivery of apomorphine via prodrug principle may be a potential treatment for Parkinson's disease. The purpose of this study was to investigate the transport and stability of apomorphine and its esters across Caco-2 cell monolayer and their affinity towards chylomicrons. Apomorphine......, monolauroyl apomorphine (MLA) and dilauroyl apomorphine (DLA) were subjected to apical to basolateral (A-B) and basolateral to apical (B-A) transport across Caco-2 cell monolayer. The stability of these compounds was also assessed by incubation at intestinal pH and physiological pH with and without Caco-2...

  1. Enzymatic synthesis of arbutin undecylenic acid ester and its inhibitory effect on melanin synthesis.

    Science.gov (United States)

    Tokiwa, Yutaka; Kitagawa, Masaru; Raku, Takao; Yanagitani, Shusaku; Yoshino, Kenji

    2007-06-01

    Transesterification of arbutin and undecylenic acid vinyl ester was catalyzed by alkaline protease, Bioprase, in dimethylformamide to get arbutin derivative having undecylenic acid at 6-position of glucose moiety, 6-O-undecylenoyl p-hydroxyphenyl beta-D-glucopyranoside. The reaction rate increased with increase of arbutin concentration, and when its concentration was 0.9 M, the conversion rate was more than 90% under addition of 2 M undecylenic acid vinyl ester. The obtained arbutin ester significantly suppressed melanin production in murine B16 melanoma cells.

  2. Optimization of the fermentation conditions and substrate specifity of mycelium-bound ester hydrolases of Aspergillus oryzae Cs007

    Directory of Open Access Journals (Sweden)

    de Hong Yan

    2015-01-01

    Full Text Available In order to improve mycelium-bound ester hydrolases activities of Aspergillus oryzae Cs007, the main production conditions were investigated. The ester hydrolases activities were simultaneously determined by titration assay and spectrophotometric assay methods, using olive oil and p-nitrophenyl esters as substrates, respectively. The optimum carbon source and nitrogen source were olive oil and peptone, with the concentrations of 1% and 2.2%, respectively. The effects of carbon source, nitrogen source and their concentrations on the production of enzymes were identical when the enzymes activities were assayed by the two methods. The mycelium-bound enzymes showed hydrolytic activity toward all the tested p-nitrophenyl esters, triglycerides and fatty acid ethyl esters. But it showed greater preference for long-chain triglycerides and short-chain p-nitrophenyl esters.

  3. [3H]cholesteryl ester labeling and transfer among human and honhuman primate plasma lipoproteins

    International Nuclear Information System (INIS)

    Thomas, M.S.; Rudel, L.L.

    1983-01-01

    Aliquots of human and nonhuman primate plasma containing 5,5'-dithiobis (2-nitrobenzoic acid) were incubated at 37 0 C in tubes previously coated with trace amounts of tritium-labeled cholesteryl oleate ([ 3 H]CO). Initially, cholesteryl esters were transferred at a rapid rate into plasma after which the rate slowed. During 24 h of incubation, an average of 55% of the [ 3 H]CO transferred from the side of the tube into African green monkey plasma, 44% into human plasma and 21% into rat plasma. Greater than 98% of the radioactive ester transferred into plasma was found to be associated with plasma lipoproteins that were then rapidly separated using vertical rotor density gradient ultracentrifugation. In very low density lipoprotein (VLDL)-poor plasma after 30 min incubations, high density lipoproteins (HDL) contained most of the [ 3 H]CO while 5- to 24-h incubations resulted in increased labeling of low density proteins (LDL). In VLDL-rich plasma, it was found that in addition to the labeling of HDL, VLDL contained about 25% of the labeled cholesteryl esters after 30-min incubations and, as above, the proportion in LDL subsequently increased. Compositional analyses showed that intermediate-sized LDL (ILDL) were accumulating cholesteryl ester mass while transfer occurred. LDL labeled using this method were injected intravenously into monkeys and their removal from plasma was found to be similar to that found for LDL labeled in vivo. It was concluded that this method of plasma lipoprotein cholesteryl ester labeling, presumably a result of cholesteryl ester transfer protein activity, was efficient, resulted in lipoproteins labeled only in the cholesteryl ester moiety, and induced minimal modification of lipoprotein particles that did not alter their biological activity

  4. Exposure assessment of 3-monochloropropane-1, 2-diol esters from edible oils and fats in China.

    Science.gov (United States)

    Li, Chang; Nie, Shao-Ping; Zhou, Yong-Qiang; Xie, Ming-Yong

    2015-01-01

    3-monochoropropane-1, 2-diol (3-MCPD) esters from edible oils are considered to be a possible risk factor for adverse effects in human. In the present study, the exposure assessment of 3-MCPD esters to Chinese population was performed. A total of 143 edible oil and fat samples collected from Chinese markets were determined for the concentrations of 3-MCPD esters. The concentration data together with the data of fats consumed were analyzed by the point evaluation and probabilistic assessment for the exposure assessment. The point evaluation showed that the mean daily intake (DI) of 3-MCPD esters were lower than the value of provisional maximum tolerable daily intake (PMTDI) of 3-MCPD (2 µg/kg BW/d). The mean DI values in different age groups obtained from probabilistic assessment were similar to the results of the point evaluation. However, in high percentiles (95th, 97.5th, 99th), the DI values in all age groups were undesirably higher than the value of PMTDI. Overall, the children and adolescents exposed more to 3-MCPD esters than the adults. Uncertainty was also analyzed for the exposure assessment. Decreasing the level of 3-MCPD esters in edible oils and consuming less oil were top priority to minimize the risk of 3-MCPD esters. Copyright © 2014 Elsevier Ltd. All rights reserved.

  5. Lubricating and Waxy Esters. VI. Effect of Symmetry about Ester on Crystallization of Linear Monoester Isomers

    Directory of Open Access Journals (Sweden)

    Laziz Bouzidi

    2014-08-01

    Full Text Available The crystal structure development of jojoba-like esters incorporating either 1-decenoic acid and/or 1-decenol, namely octadec-9-enyl dec-9-enoate (JLE-281, and its isomer dec-9-enyl oleate (JLE-282 was investigated to reveal the effect of symmetry about the ester group on crystallization of aliphatic fatty monoesters. The phase transformation path was investigated with temperature-time resolved X-ray diffraction during stepped isothermal crystallization, and while cooling from the melt at a fixed rate. Startling differences in phase behavior were uncovered between the isomers. When stepped isothermals were used, selective extinctions occurred at a transition temperature for JLE-281 but not for JLE-282. The extinctions, which are due to dramatic changes in the electronic density of certain families of planes, indicate a phase transition attributed to a brusque rearrangement of the oxygen atoms in the crystal subcell. The phase transition did not occur when the JLEs were cooled continuously. The crucial role played by the position of the alkyl chain and its orientation relative to the easy rotation site of the C–O bond in the phase trajectories of the JLEs was particularly highlighted.

  6. 75 FR 20785 - Polyglyceryl Phthalate Ester of Coconut Oil Fatty Acids; Exemption from the Requirement of a...

    Science.gov (United States)

    2010-04-21

    ... Phthalate Ester of Coconut Oil Fatty Acids; Exemption from the Requirement of a Tolerance; Technical... ester of coconut oil fatty acids; exemption from the requirement of a tolerance. This document is being... requirement of a tolerance for ``polyglyceryl phthalate ester of coconut oil fatty acids'' pursuant to a...

  7. Effects of temperature and NaCl on the formation of 3-MCPD esters and glycidyl esters in refined, bleached and deodorized palm olein during deep-fat frying of potato chips.

    Science.gov (United States)

    Wong, Yu Hua; Muhamad, Halimah; Abas, Faridah; Lai, Oi Ming; Nyam, Kar Lin; Tan, Chin Ping

    2017-03-15

    The effects of frying duration, frying temperature and concentration of sodium chloride on the formation of 3-monochloropropane-1,2-diol (3-MCPD) esters and glycidyl esters (GEs) of refined, bleached and deodorized (RBD) palm olein during deep-fat frying (at 160°C and 180°C) of potato chips (0%, 1%, 3% and 5% NaCl) for 100min/d for five consecutive days in eight systems were compared in this study. All oil samples collected after each frying cycle were analyzed for 3-MCPD esters, GEs, free fatty acid (FFA) contents, specific extinction at 232 and 268 nm (K 232 and K 268 ), p-anisidine value (pAV), and fatty acid composition. The 3-MCPD ester trend was decreasing when the frying duration increased, whereas the trend was increasing when frying temperature and concentration of NaCl increased. The GEs trend was increasing when the frying temperature, frying duration and concentration of NaCl increased. All of the oil qualities were within the safety limit. Copyright © 2016 Elsevier Ltd. All rights reserved.

  8. Phthalate esters in the environment: A critical review of their occurrence, biodegradation, and removal during wastewater treatment processes.

    Science.gov (United States)

    Gao, Da-Wen; Wen, Zhi-Dan

    2016-01-15

    Phthalate esters are one of the most frequently detected persistent organic pollutants in the environment. A better understanding of their occurrence and degradation in the environment and during wastewater treatment processes will facilitate the development of strategies to reduce these pollutants and to bioremediate contaminated freshwater and soil. Phthalate esters occur at measurable levels in different environments worldwide. For example, the concentrations of dimethyl phthalate (DMP) in atmospheric particulate matter, fresh water and sediments, soil, and landfills are N.D.-10.4 ng/m(3), N.D.-31.7 μg/L, N.D.-316 μg/kg dry weight, and N.D.-200 μg/kg dry weight, N.D.-43.27 μg/L, respectively. Bis(2-ethylhexyl) phthalate (DEHP) and di-n-butyl phthalate (DBP) are primary phthalate ester pollutants. Urbanization has increased the discharge of phthalate esters to atmospheric and aquatic environments, and the use of agricultural plastics has exacerbated soil contamination by phthalate esters in rural areas. Aerobic biodegradation is the primary manner of phthalate ester mineralization in the environment, and this process has been widely studied. Phthalate esters can be removed during wastewater treatment processes. The combination of different wastewater treatment technologies showed greater efficiency in the removal of phthalate esters than individual treatment steps, such as the combination of anaerobic wastewater treatment with a membrane bioreactor would increase the efficiency of phthalate ester removal from 65%-71% to 95%-97%. This review provides a useful framework to identify future research objectives to achieve the mineralization and elimination of phthalate esters in the environment. Copyright © 2015 Elsevier B.V. All rights reserved.

  9. Analysis of chemical signatures of alkaliphiles using fatty acid methyl ester analysis

    Directory of Open Access Journals (Sweden)

    Basha Sreenivasulu

    2017-01-01

    Full Text Available Background: Fatty acids occur in nearly all living organisms as the important predominant constituents of lipids. While all fatty acids have essentially the same chemical nature, they are an extremely diverse group of compounds. Materials and Methods: To test the hypothesis, fatty acids of alkaliphiles isolates, Bacillus subtilis SVUNM4, Bacillus licheniformis SVUNM8, Bacillus methylotrohicus SVUNM9, and Paenibacillus dendritiformis SVUNM11, were characterized compared using gas chromatography-mass spectrometry (GC-MS analysis. Results: The content of investigated ten fatty acids, 1, 2-benzenedicarboxylic acid butyl 2-methylpropyl ester, phthalic acid, isobutyl 2-pentyl ester, dibutyl phthalate, cyclotrisiloxane, hexamethyl, cyclotetrasiloxane, octamethyl, dodecamethyl, heptasiloxane 1,1,3,3,5,5,7,7,9,9,11,11,13,13-etradecamethyl, 7,15-dihydroxydehydroabietic acid, methyl ester, di (trimethylsilyl ether, hentriacontane, 2-thiopheneacetic acid, undec-2-enyl ester, obviously varied among four species, suggesting each species has its own fatty acid pattern. Conclusions: These findings demonstrated that GC-MS-based fatty acid profiling analysis provides the reliable platform to classify these four species, which is helpful for ensuring their biotechnological interest and novel chemotaxonomic.

  10. Request from the Phthalate Esters Panel of the American Chemistry Council for correction of EPA's Action Plan for Phthalate Esters

    Science.gov (United States)

    The Phthalate Esters Panel (Panel) of the American Chemistry Council submits this Request for Correction to EPA under the Guidelines for Ensuring and Maximizing the Quality, Objectivity, Utility, and Integrity, of Information Disseminated by the Environmental Protection Agency

  11. Zeolite-catalysed preparation of alpha-hydroxy carboxylic acids and esters thereof

    DEFF Research Database (Denmark)

    2010-01-01

    A process for the production of lactic acid and 2-hydroxy-3-butenoic acid or esters thereof by conversion of glucose, fructose, sucrose, xylose and glycolaldehyde dissolved in a solvent in presence of a solid Lewis acidic catalyst.......A process for the production of lactic acid and 2-hydroxy-3-butenoic acid or esters thereof by conversion of glucose, fructose, sucrose, xylose and glycolaldehyde dissolved in a solvent in presence of a solid Lewis acidic catalyst....

  12. A comparative estimation of C.I. engine fuelled with methyl esters of punnai, neem and waste cooking oil

    Energy Technology Data Exchange (ETDEWEB)

    Subramaniam, D.; Avinash, A. [Department of Mechanical Engineering - K.S.Rangasamy College of Technology –Tiruchengode, 637215 Tamil Nadu (India); Murugesan, A. [Department of Mechatronics Engineering - K.S.Rangasamy College of Technology – Tiruchengode, 637215 Tamil Nadu (India)

    2013-07-01

    In this experimental study, performance, emission, and combustion characteristics of methyl esters of Punnai, Neem, Waste Cooking Oil and their diesel blends in a C.I. engine was experimentally examined. For the study, Punnai oil methyl esters (POME), neem oil methyl esters (NOME), and Waste Cooking Oil Methyl Esters (WCOME) were prepared by tranesterification process. The Bio diesel-diesel blends were prepared by mixing 10%, 30%, 50%, and 70% of bio diesel with diesel. The effects of three methyl esters and their diesel blends on engine performance, combustion, and exhaust emissions were examined at different engine loads. Experimental results concluded that up to 30% of methyl esters did not affect the performance, combustion, and emissions characteristics. On the other hand, above B30 (30% Bio diesel with 70% diesel) a reduction in performance, combustion, and emission characteristics were clear from the study.

  13. PLE CATALYZED HYDROLYZES OF ALPHA-SUBSTITUTED ALPHA-HYDROXY ESTERS - THE INFLUENCE OF THE SUBSTITUENTS

    NARCIS (Netherlands)

    MOORLAG, H; KELLOGG, RM

    1991-01-01

    The enzymatic hydrolyses of a variety of alpha-substituted mandelic and lactic esters using pig liver esterase (PLE) have been investigated. High to moderate enantioselectivity was found for various alpha-substituted mandelic esters, whereas PLE showed low to no enantioselectivity for

  14. Studi Penggunaan Metil Ester Minyak Sawit sebagai Minyak Isolasi Peralatan Listrik

    Directory of Open Access Journals (Sweden)

    Abdul Rajab

    2014-03-01

    Full Text Available This paper discusses experimental results on some parameters of palm methyl ester as insulating oil. Destillations are firstly made to obtained the composition of oil that provide the optimal compromise among measured parameters. Breakdown voltage, dissipation factor, dielectric constant, viscosity and oxidation stability were then tested on original, destilled, and destillation residual oils. The results showed that the dissipation factor and viscosity of destilled palm methyl ester comply with the standard spesification for natural ester to be used as insulating oil. Sadly, the breakdown voltage and oxidation stability of oils do not fulfill the standard. However, the lower breakdown voltage of oils seem to be tolerable as their value are still higher then that of mineral oil. Dielectric constant of oils which were higher then that of mineral oil is an advantage when the oils will be used in combination with solid insulation for more uniformly field reason.

  15. Synthesis of Polyformate Esters of Vegetable Oils: Milkweed, Pennycress, and Soy

    Directory of Open Access Journals (Sweden)

    Rogers E. Harry-O’kuru

    2016-01-01

    Full Text Available In a previous study of the characteristics of acyl derivatives of polyhydroxy milkweed oil (PHMWO, it was observed that the densities and viscosities of the respective derivatives decreased with increased chain length of the substituent acyl group. Thus from the polyhydroxy starting material, attenuation in viscosity of the derivatives relative to PHMWO was found in the order: PHMWO ≫ PAcMWE ≫ PBuMWE ≫ PPMWE (2332 : 1733 : 926.2 : 489.4 cSt, resp., at 40°C, where PAcMWE, PBuMWE, and PPMWE were the polyacetyl, polybutyroyl, and polypentanoyl ester derivatives, respectively. In an analogous manner, the densities also decreased as the chain length increased although not as precipitously compared to the viscosity drop. By inference, derivatives of vegetable oils with short chain length substituents on the triglyceride would be attractive in lubricant applications in view of their higher densities and possibly higher viscosity indices. Pursuant to this, we have explored the syntheses of formyl esters of three vegetable oils in order to examine the optimal density, viscosity, and related physical characteristics in relation to their suitability as lubricant candidates. In the absence of ready availability of formic anhydride, we opted to employ the epoxidized vegetable oils as substrates for formyl ester generation using glacial formic acid. The epoxy ring-opening process was smooth but was apparently followed by a simultaneous condensation reaction of the putative α-hydroxy formyl intermediate to yield vicinal diformyl esters from the oxirane. All three polyformyl esters milkweed, soy, and pennycress derivatives exhibited low coefficient of friction and a correspondingly much lower wear scar in the 4-ball antiwear test compared to the longer chain acyl analogues earlier studied.

  16. Synthesis of Polyformate Esters of Vegetable Oils: Milkweed, Pennycress, and Soy.

    Science.gov (United States)

    Harry-O'kuru, Rogers E; Biresaw, Girma; Tisserat, Brent; Evangelista, Roque

    2016-01-01

    In a previous study of the characteristics of acyl derivatives of polyhydroxy milkweed oil (PHMWO), it was observed that the densities and viscosities of the respective derivatives decreased with increased chain length of the substituent acyl group. Thus from the polyhydroxy starting material, attenuation in viscosity of the derivatives relative to PHMWO was found in the order: PHMWO ≫ PAcMWE ≫ PBuMWE ≫ PPMWE (2332 : 1733 : 926.2 : 489.4 cSt, resp., at 40°C), where PAcMWE, PBuMWE, and PPMWE were the polyacetyl, polybutyroyl, and polypentanoyl ester derivatives, respectively. In an analogous manner, the densities also decreased as the chain length increased although not as precipitously compared to the viscosity drop. By inference, derivatives of vegetable oils with short chain length substituents on the triglyceride would be attractive in lubricant applications in view of their higher densities and possibly higher viscosity indices. Pursuant to this, we have explored the syntheses of formyl esters of three vegetable oils in order to examine the optimal density, viscosity, and related physical characteristics in relation to their suitability as lubricant candidates. In the absence of ready availability of formic anhydride, we opted to employ the epoxidized vegetable oils as substrates for formyl ester generation using glacial formic acid. The epoxy ring-opening process was smooth but was apparently followed by a simultaneous condensation reaction of the putative α-hydroxy formyl intermediate to yield vicinal diformyl esters from the oxirane. All three polyformyl esters milkweed, soy, and pennycress derivatives exhibited low coefficient of friction and a correspondingly much lower wear scar in the 4-ball antiwear test compared to the longer chain acyl analogues earlier studied.

  17. Osteogenic cell differentiation on H-terminated and O-terminated nanocrystalline diamond films

    Directory of Open Access Journals (Sweden)

    Liskova J

    2015-01-01

    Full Text Available Jana Liskova,1 Oleg Babchenko,2 Marian Varga,2 Alexander Kromka,2 Daniel Hadraba,1 Zdenek Svindrych,1 Zuzana Burdikova,1 Lucie Bacakova1 1Institute of Physiology, Academy of Sciences of the Czech Republic, Prague, Czech Republic; 2Institute of Physics, Academy of Sciences of the Czech Republic, Prague, Czech Republic Abstract: Nanocrystalline diamond (NCD films are promising materials for bone implant coatings because of their biocompatibility, chemical resistance, and mechanical hardness. Moreover, NCD wettability can be tailored by grafting specific atoms. The NCD films used in this study were grown on silicon substrates by microwave plasma-enhanced chemical vapor deposition and grafted by hydrogen atoms (H-termination or oxygen atoms (O-termination. Human osteoblast-like Saos-2 cells were used for biological studies on H-terminated and O-terminated NCD films. The adhesion, growth, and subsequent differentiation of the osteoblasts on NCD films were examined, and the extracellular matrix production and composition were quantified. The osteoblasts that had been cultivated on the O-terminated NCD films exhibited a higher growth rate than those grown on the H-terminated NCD films. The mature collagen fibers were detected in Saos-2 cells on both the H-terminated and O-terminated NCD films; however, the quantity of total collagen in the extracellular matrix was higher on the O-terminated NCD films, as were the amounts of calcium deposition and alkaline phosphatase activity. Nevertheless, the expression of genes for osteogenic markers – type I collagen, alkaline phosphatase, and osteocalcin – was either comparable on the H-terminated and O-terminated films or even lower on the O-terminated films. In conclusion, the higher wettability of the O-terminated NCD films is promising for adhesion and growth of osteoblasts. In addition, the O-terminated surface also seems to support the deposition of extracellular matrix proteins and extracellular matrix

  18. Diarrhetic shellfish poisoning toxin esters in Danish blue mussels and surf clams

    DEFF Research Database (Denmark)

    Jørgensen, Kevin; Scanlon, Sine Hedegaard; Jensen, L.B.

    2005-01-01

    Until recently, little focus was given to the presence of diarrhetic shellfish poisoning ( DSP) toxin esters in seafood products. However, during the last few years, the occurrence of a high percentage of esters of the total amount of DSP toxins present in some seafood products has been observed....... importance because of the increased use of chemical methods instead of mouse bioassay for the detection of DSP toxicity....

  19. Functional Group Interconversion: Decarbonylative Borylation of Esters for the Synthesis of Organoboronates

    KAUST Repository

    Guo, Lin

    2016-09-26

    A new and efficient nickel-catalyzed decarbonylative borylation reaction of carboxylic acid esters with bis(pinacolato)-diboron has been developed. This transformation allows access to structurally diverse aryl as well as alkenyl and alkyl boronate esters with high reactivity, broad substrate scope, and excellent functional-group tolerance. Further experiments show that this protocol can be carried out on a gram scale and applied to orthogonal synthetic strategies.

  20. Functional Group Interconversion: Decarbonylative Borylation of Esters for the Synthesis of Organoboronates

    KAUST Repository

    Guo, Lin; Rueping, Magnus

    2016-01-01

    A new and efficient nickel-catalyzed decarbonylative borylation reaction of carboxylic acid esters with bis(pinacolato)-diboron has been developed. This transformation allows access to structurally diverse aryl as well as alkenyl and alkyl boronate esters with high reactivity, broad substrate scope, and excellent functional-group tolerance. Further experiments show that this protocol can be carried out on a gram scale and applied to orthogonal synthetic strategies.

  1. 40 CFR 721.3680 - Ethylene oxide adduct of fatty acid ester with pentaerythritol.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Ethylene oxide adduct of fatty acid... New Uses for Specific Chemical Substances § 721.3680 Ethylene oxide adduct of fatty acid ester with... identified generically as ethylene oxide adduct of fatty acid ester with pentaerythritol (PMN P-91-442) is...

  2. Increased production of wax esters in transgenic tobacco plants by expression of a fatty acid reductase:wax synthase gene fusion.

    Science.gov (United States)

    Aslan, Selcuk; Hofvander, Per; Dutta, Paresh; Sun, Chuanxin; Sitbon, Folke

    2015-12-01

    Wax esters are hydrophobic lipids consisting of a fatty acid moiety linked to a fatty alcohol with an ester bond. Plant-derived wax esters are today of particular concern for their potential as cost-effective and sustainable sources of lubricants. However, this aspect is hampered by the fact that the level of wax esters in plants generally is too low to allow commercial exploitation. To investigate whether wax ester biosynthesis can be increased in plants using transgenic approaches, we have here exploited a fusion between two bacterial genes together encoding a single wax ester-forming enzyme, and targeted the resulting protein to chloroplasts in stably transformed tobacco (Nicotiana benthamiana) plants. Compared to wild-type controls, transgenic plants showed both in leaves and stems a significant increase in the total level of wax esters, being eight-fold at the whole plant level. The profiles of fatty acid methyl ester and fatty alcohol in wax esters were related, and C16 and C18 molecules constituted predominant forms. Strong transformants displayed certain developmental aberrations, such as stunted growth and chlorotic leaves and stems. These negative effects were associated with an accumulation of fatty alcohols, suggesting that an adequate balance between formation and esterification of fatty alcohols is crucial for a high wax ester production. The results show that wax ester engineering in transgenic plants is feasible, and suggest that higher yields may become achieved in the near future.

  3. Organizational Relationship Termination Competence

    DEFF Research Database (Denmark)

    Ritter, Thomas; Geersbro, Jens

    2011-01-01

    termination are found to significantly affect a firm's relationship termination competence. The findings suggest that managers should regard termination as a legitimate option in customer relationship management. In order to decrease the number of unwanted customers, managers must accept termination......Most firms are involved in a number of customer relationships that drain the firm's resources. However, many firms are hesitant to address this problem. This paper investigates customer relationship termination at the organizational level. We develop and analyze the organizational dimensions...... of organizational termination in order to improve our understanding of the management of termination. The impact of these termination dimensions on the percentage of unwanted customers is developed and tested using PLS on data gathered from a cross-sectional survey of more than 800 sales representatives. We find...

  4. 21 CFR 172.225 - Methyl and ethyl esters of fatty acids produced from edible fats and oils.

    Science.gov (United States)

    2010-04-01

    ... from edible fats and oils. 172.225 Section 172.225 Food and Drugs FOOD AND DRUG ADMINISTRATION... Methyl and ethyl esters of fatty acids produced from edible fats and oils. Methyl esters and ethyl esters of fatty acids produced from edible fats and oils may be safely used in food, subject to the...

  5. Lymphocyte adhesion to endothelial cell (EC) is stimulated by phorbol esters

    International Nuclear Information System (INIS)

    Haskard, D.; Cavender, D.; Ziff, M.

    1986-01-01

    The effect of phorbol esters on T cell adhesion to EC has been studied. The phorbol esters 12-0-tetradecanoyl-phorbol-13-acetate and 4-beta-phorbol-12-13-dibutyrate, but not the biologically inert 4-0-methyl-phorbol-12-13-didecanoate strongly increased the binding of 51 Cr-labeled T cells to human umbilical vein EC monolayers in microtiter wells. Increase in binding was observed at 0.3 ng/ml with maximal enhancement at 50 ng/ml. Both unstimulated and phorbol ester activated T cells displayed a substantially greater binding affinity for EC than for fibroblasts or plastic. Binding enhancement occurred within one minute, with maximal increase after 15 min. Preincubation studies showed that binding enhancement was entirely attributable to an effect on T cells, with no action on EC. Additive binding enhancement was seen when phorbol esters and reagents that increase adhesion by actions on EC (LPS, IL-1 and IFN-γ) were used together. Increase in adhesion of activated T lymphocytes to EC may explain the greater emigration of activated T cells than small resting T cells into inflammatory foci in vivo. The rapid onset of the phorbol effect suggests that this may be an important mechanism for immediate localization of circulating T cells in the cellular immune response, activated, perhaps, at the endothelial blood-tissue interface

  6. Kitimat LNG terminal

    International Nuclear Information System (INIS)

    Schmaltz, I.; Boulton, R.

    2007-01-01

    Kitimat Liquefied Natural Gas (LNG) terminal is a terminal development company owned by Galveston LNG, a privately owned Canadian energy development company. This presentation provided information on Kitimat LNG with particular reference to its terminal located in Bish Cove on the Douglas Channel in British Columbia. This LNG terminal is reported to be the only fully permitted regasification terminal on the west coast of Canada and the United States. The presentation addressed market fundamentals including several graphs, such as world natural gas proved reserves in 2006; LNG supplements to Canadian gas supplies; global LNG demand for 2005-2020; average annual United States LNG imports; and global LNG liquefaction projects. Other market fundamentals were described, including that Kitimat is the only other approved terminal aside from the Costa Azul terminal in Mexico; Kitimat is the only west coast LNG import terminal that connects to midwest and eastern North American markets through existing gas pipelines; LNG producers are looking for destination diversification; and markets and marketers are looking for supply diversification. The authors noted that by 2010, western Canadian gas demand will exceed Californian demand. Other topics that were discussed in the presentation included Canadian natural gas field receipts; unadjusted bitumen production outlook; oil sands gas demand; forward basis fundamentals; and the commercial drivers of the Kitimat LNG terminal. The presentation also discussed the pacific trail pipelines, a partnership between Galveston LNG and Pacific Northern Gas to develop the natural gas transmission line from Kitimat to Summit. The presentation concluded with a discussion of the benefits of Kitimat LNG terminal such as providing access to the largest natural gas markets in the world via major gas transmission lines with spare capacity. figs

  7. NHS-Esters As Versatile Reactivity-Based Probes for Mapping Proteome-Wide Ligandable Hotspots.

    Science.gov (United States)

    Ward, Carl C; Kleinman, Jordan I; Nomura, Daniel K

    2017-06-16

    Most of the proteome is considered undruggable, oftentimes hindering translational efforts for drug discovery. Identifying previously unknown druggable hotspots in proteins would enable strategies for pharmacologically interrogating these sites with small molecules. Activity-based protein profiling (ABPP) has arisen as a powerful chemoproteomic strategy that uses reactivity-based chemical probes to map reactive, functional, and ligandable hotspots in complex proteomes, which has enabled inhibitor discovery against various therapeutic protein targets. Here, we report an alkyne-functionalized N-hydroxysuccinimide-ester (NHS-ester) as a versatile reactivity-based probe for mapping the reactivity of a wide range of nucleophilic ligandable hotspots, including lysines, serines, threonines, and tyrosines, encompassing active sites, allosteric sites, post-translational modification sites, protein interaction sites, and previously uncharacterized potential binding sites. Surprisingly, we also show that fragment-based NHS-ester ligands can be made to confer selectivity for specific lysine hotspots on specific targets including Dpyd, Aldh2, and Gstt1. We thus put forth NHS-esters as promising reactivity-based probes and chemical scaffolds for covalent ligand discovery.

  8. Ultrasonic pretreatment for lipase-catalyed synthesis of phytosterol esters with different acyl donors.

    Science.gov (United States)

    Zheng, Ming-Ming; Wang, Lian; Huang, Feng-Hong; Dong, Ling; Guo, Ping-Mei; Deng, Qian-Chun; Li, Wen-Lin; Zheng, Chang

    2012-09-01

    This study is focused on the enzymatic esterification of phytosterols with different acyl donors to produce the corresponding phytosterol esters catalyzed by Canadia sp. 99-125 lipase under ultrasound irradiation. An ultrasonic frequency of 35 kHz, power of 200 W and time of 1h was determined to guarantee satisfactory degree of esterification and lipase activity. The influence of temperature, substrates concentration and molar ratio was investigated subsequently. The optimum production was achieved in isooctane system at 60°C with phytosterol concentration of 150 μmol/mL and phytosterol to fatty acid molar ratio of 1:1.5, resulting in a phytosterol esters conversion of above 85.7% in short reaction time (8h). Phytosterols esters could also be converted in high yields to the corresponding long-chain acyl esters via transesterification with triacylglycerols (above 90.3%) under ultrasound irradiation. In optimum conditions, the overall esterification reaction rate using the ultrasonic pretreatment process was above 2-fold than that of mechanical stirring process without damage the lipase activity. Copyright © 2012 Elsevier B.V. All rights reserved.

  9. In vitro incorporation of radiolabeled cholesteryl esters into high and low density lipoproteins

    International Nuclear Information System (INIS)

    Terpstra, A.H.; Nicolosi, R.J.; Herbert, P.N.

    1989-01-01

    We have developed and validated a method for in vitro incorporation of radiolabeled cholesteryl esters into low density (LDL) and high density lipoproteins (HDL). Radiolabeled cholesteryl esters dissolved in absolute ethanol were mixed with LDL or HDL in the presence of lipoprotein-deficient serum (LPDS) as a source of core lipid transfer activity. The efficiency of incorporation was dependent on: (a) the core lipid transfer activity and quantity of LPDS, (b) the mass of added radiolabeled cholesteryl esters, (c) the length of incubation, and (d) the amount of acceptor lipoprotein cholesterol. The tracer incorporation was documented by repeat density gradient ultracentrifugation, agarose gel electrophoresis, and precipitation with heparin-MnCl2. The radiolabeling conditions did not affect the following properties of the lipoproteins: (1) chemical composition, (2) electrophoretic mobility on agarose gels, (3) hydrated density, (4) distribution of apoproteins on SDS gels, (5) plasma clearance rates, and (6) immunoprecipitability of HDL apoproteins A-I and A-II. Rat HDL containing radiolabeled cholesteryl esters incorporated in vitro had plasma disappearance rates identical to HDL radiolabeled in vivo

  10. [Analysis of constituents of ester-type gum bases used as natural food additives].

    Science.gov (United States)

    Tada, Atsuko; Masuda, Aino; Sugimoto, Naoki; Yamagata, Kazuo; Yamazaki, Takeshi; Tanamoto, Kenichi

    2007-12-01

    The differences in the constituents of ten ester-type gum bases used as natural food additives in Japan (urushi wax, carnauba wax, candelilla wax, rice bran wax, shellac wax, jojoba wax, bees wax, Japan wax, montan wax, and lanolin) were investigated. Several kinds of gum bases showed characteristic TLC patterns of lipids. In addition, compositions of fatty acid and alcohol moieties of esters in the gum bases were analyzed by GC/MS after methanolysis and hydrolysis, respectively. The results indicated that the varieties of fatty acids and alcohols and their compositions were characteristic for each gum base. These results will be useful for identification and discrimination of the ester-type gum bases.

  11. Determination of Alkyl Esters Content in PDO Extra Virgin Olive Oils from Sicily

    Directory of Open Access Journals (Sweden)

    Rosaria Costa

    2017-01-01

    Full Text Available The quality parameter of alkyl esters of fatty acids was checked in a variety of Italian olive oil samples. In particular, 34 samples of extra virgin olive oils (EVOOs from South Italy (Sicilian orchards, produced in the years 2014-2015, have been subjected to the analytical protocol dictated by the European Union for the determination of alkyl esters, as an indicator of oil’s quality. All the samples analyzed resulted to be well below the limit set by EU Directive. Besides recently produced EVOOs, a set of very aged oils, produced in the years 1996–2000, were analyzed as well. The main finding was that alkyl esters increased in correspondence with deterioration processes.

  12. Emission and Mechanical Evaluations of Vinyl-Ester Resin Systems

    National Research Council Canada - National Science Library

    Sands, James

    2003-01-01

    Vinyl-ester resins (VE) are frequently used in liquid molding of composite materials for several applications including naval and army structures, commercial boat manufacturing, and building construction...

  13. Preparation and study of novel poly(sulfone-ester-amide)s

    Energy Technology Data Exchange (ETDEWEB)

    Bruma, M. [Institute of Macromolecular Chemistry, Isai (Romania)], Mercer, F. [Raychem Corporation, Menlo Park, CA (United States); Gronewald, S. [Southwest Texas State Univ., San Marcos, TX (United States)] [and others

    1995-12-31

    A series of novel poly(ester-amide)s containing sulfone groups in the main chain have been prepared and compared with related polymers which do not have sulfone bridges. Incorporation of sulfone moieties into the polymer backbone improved the solubility of these polymers without significant loss of their high thermal stability, and provided a large {open_quotes}window{close_quotes} between T{sub g} and decomposition temperature. Solutions of poly(sulfone-ester-amide)s in NMP have been cast into flexible films, having low dielectric constant. The synthesis and characterization of these new polymers will be presented.

  14. Transesterification of Vegetable Oils with Ethanol and Characterization of the Key Fuel Properties of Ethyl Esters

    Directory of Open Access Journals (Sweden)

    Stamoulis Stournas

    2009-06-01

    Full Text Available The transesterification reactions of four different vegetable oils (sunflower, rapeseed, olive oil and used frying oil with ethanol, using sodium hydroxide as catalyst, were studied. The ester preparation involved a two-step transesterification reaction, followed by purification. The effects of the mass ratio of catalyst to oil (0.25 – 1.5%, the molar ratio of ethanol to oil (6:1 – 12:1, and the reaction temperature (35 – 90 °C were studied for the conversion of sunflower oil to optimize the reaction conditions in both stages. The rest of the vegetable oils were converted to ethyl esters under optimum reaction parameters. The optimal conditions for first stage transesterification were an ethanol/oil molar ratio of 12:1, NaOH amount (1% wt/wt, and 80 °C temperature, whereas the maximum yield of ethyl esters reached 81.4% wt/wt. In the second stage, the yield of ethyl esters was improved by 16% in relation with the one-stage transesterification, which was obtained under the following optimal conditions: catalyst concentration 0.75% and ethanol/oil molar ratio 6:1. The fuel properties of the esters were measured according to EN test methods. Based on the experimental results one can see that the ethyl esters do not differ significantly from methyl esters. Moreover, the results showed that the values of density, viscosity, and higher heating value of ethyl esters were similar to those of automotive and heavy duty engine diesel fuel. However, the CFPP values were higher, which may contribute to potential difficulties in cold starts. On the other hand, the flash points, which were higher than those of diesel fuel constituted a safety guarantee from the point of view of handling and storage.

  15. Dietary exposure and human risk assessment of phthalate esters based on total diet study in Cambodia

    International Nuclear Information System (INIS)

    Cheng, Zhang; Li, Han-Han; Wang, Hong-sheng; Zhu, Xue-Mei; Sthiannopkao, Suthipong; Kim, Kyoung-Woong; Yasin, Mohamed Salleh Mohamed; Hashim, Jamal Hisham; Wong, Ming-Hung

    2016-01-01

    Phthalate esters are used in a wide variety of consumer products, and human exposure to this class of compounds is widespread. Nevertheless, studies on dietary exposure of human to phthalates are limited. In this study, to assess the daily intakes of phthalate esters and the possible adverse health impacts, different food samples were collected from three areas of Cambodia, one of the poorest countries in the world. The ∑phthalate ester concentrations in Kampong Cham, Kratie and Kandal provinces ranged from 0.05 to 2.34 (median 0.88) μg g −1 , 0.19–1.65 (median 0.86) μg g −1 and 0.24–3.05 (median 0.59) μg g −1 wet weight (ww), respectively. Di-2-Ethylhexyl phthalate (DEHP) and diisobutyl phthalate (DiBP) were the predominant compounds among all foodstuffs. The estimated daily intake (EDI) of phthalate esters for the general population in Kampong Cham, Kratie and Kandal was 34.3, 35.6 and 35.8 μg kg −1 bw d −1 , respectively. The dietary daily intake of DEHP, benzylbutyl phthalate (BBP) and di-n-butyl phthalate (DBP) in Kampong Cham, Kratie and Kandal were below the tolerable daily intakes (TDI) imposed by the European Food Safety Authority (EFSA) and reference doses (RfD) imposed by The United States Environmental Protection Agency (USEPA). Rice contributed the greatest quantity of DEHP to the daily intake in Cambodia so may deserve further exploration. To our knowledge, this is the first study to investigate the occurrence and the daily intakes of phthalate esters in Cambodia. - Highlights: • Phthalate esters concentration in daily foodstuffs collected from Cambodia. • Investigate the bioaccessbility of phthalate esters via the foodstuffs consumption. • Health risk evaluation of dietary exposure to phthalate esters.

  16. Dietary exposure and human risk assessment of phthalate esters based on total diet study in Cambodia

    Energy Technology Data Exchange (ETDEWEB)

    Cheng, Zhang; Li, Han-Han [College of Environment, Sichuan Agricultural University, Chengdu 611130 (China); Wang, Hong-sheng [Department of Microbial and Biochemical Pharmacy, School of Pharmaceutical Sciences, Sun Yat-sen University, No.132 Waihuandong Road, University Town, Guangzhou 510006 (China); Zhu, Xue-Mei [College of Environment, Sichuan Agricultural University, Chengdu 611130 (China); Sthiannopkao, Suthipong [Department of Environmental and Occupational Health, National Cheng Kung University, Tainan City, Taiwan (China); Kim, Kyoung-Woong [School of Environmental Science and Engineering, Gwangju Institute of Science and Technology, Gwangju (Korea, Republic of); Yasin, Mohamed Salleh Mohamed; Hashim, Jamal Hisham [United Nations University-International Institute for Global Health, Kuala Lumpur (Malaysia); Wong, Ming-Hung, E-mail: minghwong@ied.edu.hk [Consortium on Health, Environment, Education and Research (CHEER), and Department of Science and Environmental Studies, Hong Kong Institute of Education, Tai Po, Hong Kong (China); School of Environment, Jinan University, Guangzhou (China)

    2016-10-15

    Phthalate esters are used in a wide variety of consumer products, and human exposure to this class of compounds is widespread. Nevertheless, studies on dietary exposure of human to phthalates are limited. In this study, to assess the daily intakes of phthalate esters and the possible adverse health impacts, different food samples were collected from three areas of Cambodia, one of the poorest countries in the world. The ∑phthalate ester concentrations in Kampong Cham, Kratie and Kandal provinces ranged from 0.05 to 2.34 (median 0.88) μg g{sup −1}, 0.19–1.65 (median 0.86) μg g{sup −1} and 0.24–3.05 (median 0.59) μg g{sup −1} wet weight (ww), respectively. Di-2-Ethylhexyl phthalate (DEHP) and diisobutyl phthalate (DiBP) were the predominant compounds among all foodstuffs. The estimated daily intake (EDI) of phthalate esters for the general population in Kampong Cham, Kratie and Kandal was 34.3, 35.6 and 35.8 μg kg{sup −1} bw d{sup −1}, respectively. The dietary daily intake of DEHP, benzylbutyl phthalate (BBP) and di-n-butyl phthalate (DBP) in Kampong Cham, Kratie and Kandal were below the tolerable daily intakes (TDI) imposed by the European Food Safety Authority (EFSA) and reference doses (RfD) imposed by The United States Environmental Protection Agency (USEPA). Rice contributed the greatest quantity of DEHP to the daily intake in Cambodia so may deserve further exploration. To our knowledge, this is the first study to investigate the occurrence and the daily intakes of phthalate esters in Cambodia. - Highlights: • Phthalate esters concentration in daily foodstuffs collected from Cambodia. • Investigate the bioaccessbility of phthalate esters via the foodstuffs consumption. • Health risk evaluation of dietary exposure to phthalate esters.

  17. Synthesis and antiproliferative properties of new hydrophilic esters of triterpenic acids.

    Science.gov (United States)

    Eignerova, Barbara; Tichy, Michal; Krasulova, Jana; Kvasnica, Miroslav; Rarova, Lucie; Christova, Romana; Urban, Milan; Bednarczyk-Cwynar, Barbara; Hajduch, Marian; Sarek, Jan

    2017-11-10

    To improve the properties of cytotoxic triterpenoid acids 1-5, a large set of hydrophilic esters was synthesized. We choose betulinic acid (1), dihydrobetulinic acid (2), 21-oxoacid 3 along with highly active des-E lupane acids 4 and 5 as a model set of compounds for esterification of which the properties needed to be improved. As ester moieties were used - methoxyethanol and 2-(2-methoxyethoxy)ethanol and glycolic unit (type a-d), pyrrolidinoethanol, piperidinoethanol and morpholinoethanol (type f-h), and monosaccharide groups (type i-l). As a result, 56 triterpenic esters (49 new compounds) were obtained and their cytotoxicity on four cancer cell lines and normal human fibroblasts was tested. All new compounds were fully soluble at all tested concentrations, which used to be a problem of the parent compounds 1 and 2. 16 compounds had IC 50  acids 1-5. Copyright © 2017 Elsevier Masson SAS. All rights reserved.

  18. Nanoscale Characterization of Glass Flake Filled Vinyl Ester Anti-Corrosion Coatings

    Directory of Open Access Journals (Sweden)

    Salim Barbhuiya

    2017-08-01

    Full Text Available Vinyl ester is a thermoset matrix resin that is widely used in the coating industry. The presence of glass flakes further enhances the anti-corrosion performance of this coating. This paper reports the nanoscaled characterization of glass flake filled vinyl ester anti-corrosion coatings on mild steel. Bond strength properties of one uncoated and four coated samples with different thicknesses (300, 600, 900 and 1200 μm were studied using nanoscratch technique and ASTM Standard Test. It was found that the bond strength of coating with thickness 900 μm was the highest. The frequency distributions of elastic modulus on coating with 900 μm thickness determined using nanoindentation indicated that only 20–25% of the coating is composed of glass flakes and the balance is vinyl ester matrix. The critical depth at which the material is subject to failure due to external load and abrasion, was found to be around 100 nm.

  19. Combustion of Pure, Hydrolyzed and Methyl Ester Formed of Jatropha Curcas Lin oil

    Directory of Open Access Journals (Sweden)

    Muhaji Muhaji

    2015-10-01

    Full Text Available The density and viscosity of vegetable oil are higher than that of diesel oil. Thus its direct combustion in the diesel engine results many problems. This research was conducted to investigate the flame characteristics of combustion of jatropha curcas lin in pure, hydrolyzed and methyl ester form. The results indicated that the combustion of pure jatropha curcas lin occurs in three stages, hydrolyzed in two stages    and methyl ester in one stage. For pure jatropha curcas lin, in the first stage, unsaturated fatty acid burned for  0.265 s.  It is followed by saturated fatty acid, burned for 0.389 s in the second stage. And, in the last stage is the burned of glycerol for 0.560 s. Meanwhile for hydrolyzed one, in the first stage, unsaturated fatty acid burned for 0.736 s, followed by saturated fatty acid, burned  for 0.326 s in the second stage. And the last, for methyl ester is the burned for 0.712 s. The highest burning rate was for methyl ester which was 0.003931cc/s. The energy releasing rate of methyl ester, which was for 13,628.67 kcal/(kg.s resembled that of diesel oil the most, while the lowest rate was for pure jatropha curcas lin which was 8,200.94 kcal/(kg.s. In addition, massive explosion occurred in the fuel containing unsaturated fatty acid and glycerol

  20. Analysis of Polyadipate Ester Content in PVC Plastics by Means of FT-Raman Spectroscopy

    DEFF Research Database (Denmark)

    Berg, Rolf W.

    2006-01-01

    Plasticizers are needed in flexible PVC (PolyVinylChloride) products. There is serious concern that commonly used phthalate esters may harm life reproduction systems. To avoid the problems, instead adipate di-esters (AEs) of C8 to C10 alcohols are used as higher prized alternatives; e.g. di-2......-ethylhexyl adipate or DEHA [103-23-1], also known as Adimoll or di-octyl adipate, DOA. A widely used plasticizer in food (cling) films is DEHA, often in combination with polymers, epoxidized soya-bean oil, etcetera. DEHA also occurs in children toys. We have previously shown that the presence of phthalate...... esters in PVC can be rapidly analyzed by Fourier transform (FT-) Raman spectroscopy excited with a 1064 nm laser. Here in this project we report a similar study. The aim was to find out whether FT-Raman spectroscopy can be used to determine the presence of adipate esters (AEs) as plasticizers...

  1. Effect of sugar fatty acid esters on rumen fermentation in vitro

    OpenAIRE

    Wakita, M.; Hoshino, S.

    1987-01-01

    1.The effect of sugar fatty acid esters (SFEs; currently used as food additives for human consumption) on rumen volatile fatty acids (VFA) and gas production was studied with sheep rumen contents in vitro.2. Some SFEs having monoester contents of more than 70% increased the molar proportion of propionate in conjunction with reduction in the acetate: propionate ratio when the individual SFE was added to rumen contents in a final concentration of 4 g/l. Laurate sugar ester was the most potent p...

  2. A preliminary study of ester oxidation on an aluminum surface using chemiluminescence

    Science.gov (United States)

    Jones, William R., Jr.; Meador, Michael A.; Morales, Wilfredo

    1987-01-01

    The oxidation characteristics of a pure ester (trimethyolpropane triheptanoate) were studied by using a chemiluminescence technique. Tests were run in a thin-film micro-oxidation apparatus with an aluminum alloy catalyst. Conditions included a pure oxygen atmosphere and a temperature range of 176 to 206 C. Results indicated that oxidation of the ester (containing 10 to the minus 3rd power M diphenylanthracene as an intensifier) was accompanied by emission of light. The maximum intensity of light emission (I sub max) was a function of the amount of ester, the concentration of intensifier, and the test temperature. The induction period or the time to reach one-half of maximum intensity (t sub 1/2) was an inverse function of test temperature. Decreases in light emission at the later stages of a test were caused by depletion of the intensifier.

  3. Sucrose fatty esters from underutilized seed oil of Terminalia catappa as potential steel corrosion inhibitor in acidic medium

    Directory of Open Access Journals (Sweden)

    Adewale Adewuyi

    2016-12-01

    Full Text Available Corrosion of metals is a common problem which requires definite attention. In response to this, the oil was extracted from the seed of Terminalia catappa and used to synthesize sucrose fatty esters via simple reaction mechanism which was considered eco-friendly and sustainable. The corrosion inhibition capacity of sucrose fatty esters for mild steel in 1 M HCl was studied using the weight loss method. It was shown that sucrose fatty ester inhibited corrosion process of mild steel and obeyed Langmuir isotherm. Corrosion rate and inhibition efficiency of sucrose fatty esters were found to reduce with increase of immersion time. The study presented sucrose fatty ester as a promising inhibitor of mild steel corrosion in acidic medium.

  4. Synthesis, characterization and application of lipase-conjugated citric acid-coated magnetic nanoparticles for ester synthesis using waste frying oil.

    Science.gov (United States)

    Patel, Unisha; Chauhan, Kishor; Gupte, Shilpa

    2018-04-01

    In the present work, magnetic nanoparticles (MNPs) were prepared by chemical precipitation of trivalent and divalent iron ions which were functionalized using citric acid. The bacterial isolate Staphylococcus epidermidis KX781317 was isolated from oil-contaminated site. The isolate produced lipase, which was purified and immobilized on magnetic nanoparticles (MNPs) for ester synthesis from waste frying oil (WFO). The characterization of MNPs employed conventional TEM, XRD and FTIR techniques. TEM analysis of MNPs showed the particle size in the range of 20-50 nm. FTIR spectra revealed the binding of citric acid to Fe 3 O 4 and lipase on citric acid-coated MNPs. The citric acid-coated MNPs and lipase-conjugated citric acid-coated MNPs had similar XRD patterns which indicate MNPs could preserve their magnetic properties. The maximum immobilization efficiency 98.21% of lipase-containing citric acid-coated MNPs was observed at ratio 10:1 of Cit-MNPs:lipase. The pH and temperature optima for lipase conjugated with Cit-MNPs were 7 and 35 °C, respectively. Isobutanol was found to be an effective solvent for ester synthesis and 1:2 ratio of oil:alcohol observed significant for ester formation. The ester formation was determined using TLC and the % yield of ester conversion was calculated. The rate of ester formation is directly proportional to the enzyme load. Formed esters were identified as isobutyl laurate ester and isobutyl myristate ester through GC-MS analysis.

  5. Synthesis and Proapoptotic Activity on Cervical Cancer Cell of Ester Eugenol 1-(3-Methoxy-4-hydroxy)phenyl-2-propylmethanoate

    Science.gov (United States)

    Farid Rahman, Moh.; Nazhif Haykal, Muhammad; Andriani Siagian, Novi; Maiselina Sriepindonnta, Priscilla; Tampubolon, Norman Alexander

    2018-01-01

    Proapoptotic activity of ester eugenol,1-(3-methoxy-4-hydroxy)phenyl-2-propylmethanoat, which synthesized from eugenol is reported. Eugenol as starting material in the synthesis of ester eugenol was obtained from fractional distillation of clove oil with the yield of 70.66%. Synthesis of ester eugenol was camed out by addition-esterification reaction through reaction between eugenol and formic acid with mol ratio of 1:27 and reaction time for11 h. GC-MS analysis showed ester eugenol was afforded purity of 92.42% and the yield in of 93.34%. UV spectra of ester eugenol was observed the formation of carbonyl group at λmax 290 nm and supported by FT-IR analysis at 1714.60 cm-1 (carbonyl group), 1193.65 cm-1 (C-O-C ester group) and the absence of vynil group in eugenol structure at region 914.20 and 995.20 cm-1. Mass spectra showed ion molecule at m/z 210 was accordance with molecular weight of ester eugenol. Afterward, HeLa cell culture media was prepared for cervical cancer antiproliferative test. The result which showed in histogram indicated that LC50 of ester eugenol was reached at concentration below 0.01% while eugenol was up to 0.01% that observed cervical cancer cell apoptotic activity. LC50 value of ester eugenol was obtained at concentration 48.73 ppm. This research reported that natural product modified its structure has potency to cure cervical cancer.

  6. Effect of sugar fatty acid esters on rumen fermentation in vitro.

    Science.gov (United States)

    Wakita, M; Hoshino, S

    1987-11-01

    1. The effect of sugar fatty acid esters (SFEs; currently used as food additives for human consumption) on rumen volatile fatty acids (VFA) and gas production was studied with sheep rumen contents in vitro. 2. Some SFEs having monoester contents of more than 70% increased the molar proportion of propionate in conjunction with reduction in the acetate:propionate ratio when the individual SFE was added to rumen contents in a final concentration of 4 g/l. Laurate sugar ester was the most potent propionate enhancer and rumen gas depressor, the effective dose being as low as 1 g/l in a final concentration. Fatty acid esters other than SFEs had little, if any, effect on rumen VFA production and their molar proportions. 3. Approximately 50% of laurate sugar ester was hydrolysed by in vitro incubation with rumen fluid for 2 h. The addition of fatty acids and sucrose was also effective in the alterations of rumen VFA and gas production. However, the effect of SFEs on in vitro rumen fermentation was significantly greater than that of their constituent fatty acids or sucrose, or both. Accordingly, the effect appeared to be ascribed to the complex action of SFE itself and to its constituents, free fatty acids and sucrose. 4. SFEs, at the level of 4 g/l, reduced substantially the froth formation (ingesta volume increase) and seemed to be effective for the prevention of bloat.

  7. Quorum Sensing Inhibition and Structure–Activity Relationships of β-Keto Esters

    Directory of Open Access Journals (Sweden)

    Stephanie Forschner-Dancause

    2016-07-01

    Full Text Available Traditional therapeutics to treat bacterial infections have given rise to multi-drug resistant pathogens, which pose a major threat to human and animal health. In several pathogens, quorum sensing (QS—a cell-cell communication system in bacteria—controls the expression of genes responsible for pathogenesis, thus representing a novel target in the fight against bacterial infections. Based on the structure of the autoinducers responsible for QS activity and other QS inhibitors, we hypothesize that β-keto esters with aryl functionality could possess anti-QS activity. A panel of nineteen β-keto ester analogs was tested for the inhibition of bioluminescence (a QS-controlled phenotype in the marine pathogen Vibrio harveyi. Initial screening demonstrated the need of a phenyl ring at the C-3 position for antagonistic activity. Further additions to the phenyl ring with 4-substituted halo groups or a 3- or 4-substituted methoxy group resulted in the most active compounds with IC50 values ranging from 23 µM to 53 µM. The compounds additionally inhibit green fluorescent protein production by E. coli JB525. Evidence is presented that aryl β-keto esters may act as antagonists of bacterial quorum sensing by competing with N-acyl homoserine lactones for receptor binding. Expansion of the β-keto ester panel will enable us to obtain more insight into the structure–activity relationships needed to allow for the development of novel anti-virulence agents.

  8. Ocular Pharmacokinetics of Acyclovir Amino Acid Ester Prodrugs in the Anterior Chamber: Evaluation of Their Utility in Treating Ocular HSV Infections

    Science.gov (United States)

    Katragadda, Suresh; Gunda, Sriram; Hariharan, Sudharshan; Mitra, Ashim K.

    2008-01-01

    Purpose To evaluate in vivo corneal absorption of the amino acid prodrugs of acyclovir (ACV) using a topical well model and microdialysis in rabbits. Methods Stability of L-Alanine-ACV (AACV), L-Serine-ACV (SACV), L-Isoleucine-ACV (IACV), γ-Glutamate-ACV (EACV) and L-Valine-ACV (VACV) prodrugs was evaluated in various ocular tissues. Dose dependent toxicity of these prodrugs was also examined in rabbit primary corneal epithelial cell culture (rPCEC) using 96-well based cell proliferation assay. In vivo ocular bioavailability of these compounds was also evaluated with a combination of topical well infusion and aqueous humor microdialysis techniques. Results Among the amino acid ester prodrugs, SACV was most stable in aqueous humor. Enzymatic degradation of EACV was the least compared to all other prodrugs. Cellular toxicity of all the prodrugs was significantly less compared to trifluorothymidine (TFT) at 5mM. Absorption rate constants of all the compounds were found to be lower than the elimination rate constants. All the prodrugs showed similar terminal elimination rate constants (λz). SACV and VACV exhibited approximately two fold increase in area under the curve (AUC) relative to ACV (p cornea at varying rates (ka) thereby leading to varying extents (AUC). The amino acid ester prodrug, SACV owing to its enhanced stability, comparable AUC, and high concentration at last time point (Clast) seems to be a promising candidate for the treatment of ocular HSV infections. PMID:18472234

  9. The majority of vitamin A is transported as retinyl esters in the blood of most carnivores.

    Science.gov (United States)

    Schweigert, F J; Ryder, O A; Rambeck, W A; Zucker, H

    1990-01-01

    1. In canines and mustelides total vitamin A was 10-50 times higher compared to other species due to a high amount of retinyl esters (40-99% of total vitamin A) in blood plasma. The dominant vitamin A ester was in most species retinyl stearate. 2. In Ursidae, Procyonidae, Viveridae and Felidae, total vitamin A was much lower. When present, however, retinyl esters also represented 10-65% of total vitamin A in plasma. 3. Only retinol was detected in plasma of the family, Hyaenidae, and the suborder, Pinnipedia. 4. In maned wolf cubs it was found that retinol, retinyl esters and alpha-tocopherol increased with the age of the animals, reaching values comparable to adult animals at the age of 5 months.

  10. The sonochemical arylation of malonic esters mediated by manganese triacetate.

    Science.gov (United States)

    Meciarova, M; Toma, S; Luche, J L

    2001-04-01

    The intermolecular arylation of malonate esters in acetic acid solution in the presence of manganese(III) triacetate is known to proceed via an Electron Transfer mechanism. Under sonication, this reaction undergoes only minor changes. In contrast, the intramolecular reaction of dimethyl alpha-(3-phenylpropyl)malonate provides a new case of sonochemical switching, with the formation of compounds 7-9, while conventional thermal conditions generate only the bicyclic compound 6. Reactions using the more powerful oxidant, cerium ammonium nitrate are governed by the formation of the nitrate ester 11. Compounds 7-9 are isolated in yields lower than with MnTA, and in proportions depending on the conditions, thermal or sonochemical.

  11. Synthesis of Dipeptide Benzoylalanylglycine Methyl Ester and Corrosion Inhibitor Evaluation by Tafel Equation

    International Nuclear Information System (INIS)

    Abdurrahman, J.; Wahyuningrum, D.; Achmad, S.; Bundjali, B.

    2011-01-01

    Corrosion is one of the major problems in petroleum mining and processing industry. The pipelines used to transport crude oil from reservoir to the processing installation were made from carbon steel that is susceptible towards corrosion. One of the best methods to prevent corrosion that occurred at the inner parts of carbon steel pipelines is to use organic corrosion inhibitor. One of the potent organic corrosion inhibitors is amino acids derivatives. In this study, dipeptide compound namely benzoylalanylglycine methyl ester and benzoylalanylglycine have been synthesized. The structure elucidation of the products was performed by IR, MS and NMR spectroscopy. The determination of corrosion inhibition activity utilized the Tafel method. The corrosion inhibition efficiency of glycine methyl ester, benzoyl alanine, dipeptide benzoylalanylglycine methyl ester and dipeptide benzoylalanylglycine were 63.34 %, 35.86 %, 68.40 % and 27.72 %, respectively. These results showed that the formation of dipeptide benzoylalanylglycine methyl ester, derived from carboxylic protected glycine and amine protected alanine, increased the corrosion inhibition activity due to the loss of acidity center in the structure of glycine and L-alanine that would induce the corrosive environment towards carbon steel. (author)

  12. Safety evaluation of phytosterol esters. Part 3. Two-generation reproduction study in rats with phytosterol esters - A novel functional food

    NARCIS (Netherlands)

    Waalkens-Berendsen, D.H.; Wolterbeek, A.P.M.; Wijnands, M.V.W.; Richold, M.; Hepburn, P.A.

    1999-01-01

    Phytosterol esters (PE) are intended for use as a novel food ingredient with plasma cholesterol lowering activity which works by inhibiting the absorption of cholesterol from the gut. Although PE are naturally present in the normal diet, the levels are insufficiently large to ensure lowering of

  13. Atomistic Simulations of Functional Au-144(SR)(60) Gold Nanoparticles in Aqueous Environment

    DEFF Research Database (Denmark)

    Heikkila, E.; Gurtovenko, A. A.; Martinez-Seara, H.

    2012-01-01

    and Cl-/Na+ counterions, respectively. The radial distribution functions show that the side chains and terminal groups show significant flexibility. The orientation of water is distinct in the first solvation shell, and AuNPs cause a long-range effect in the solvent structure. The radial electrostatic...... of the nanoparticle together with surrounding ions and water. We focus on Au-144 nanoparticles that comprise a nearly spherical Au core (diameter similar to 2 nm), a passivating Au-S interface, and functionalized alkanethiol chains. Cationic and anionic AuNPs have been modeled with amine and carboxyl terminal groups...... in aqueous solutions. They suggest that electrostatics is one of the central factors in complexation of AuNPs with other nanomaterials and biological systems, and that effects of electrostatics as water-mediated interactions are relatively long-ranged, which likely plays a role in, e.g., the interplay...

  14. Novel acyloxy derivatives of branched mono- and polyol esters of sal fat: multiviscosity grade lubricant base stocks.

    Science.gov (United States)

    Kamalakar, Kotte; Sai Manoj, Gorantla N V T; Prasad, Rachapudi B N; Karuna, Mallampalli S L

    2014-12-10

    Sal fat, a nontraditional seed oil, was chemically modified to obtain base stocks with a wide range of specifications that can replace mineral oil base stocks. Sal fatty acids were enriched to 72.6% unsaturation using urea adduct method and reacted with branched mono alcohol, 2-ethylhexanol (2-EtH), and polyols namely neopentyl glycol (NPG) and trimethylolpropane (TMP) to obtain corresponding esters. The esters were hydroxylated and then acylated using propionic, butyric, and hexanoic anhydrides to obtain corresponding acylated derivatives. The acylated TMP esters exhibited very high viscosities (427.35-471.93 cSt at 40 °C) similar to those of BS 150 mineral oil base stock range, ISO VG 460, while the acylated NPG esters (268.81-318.84 cSt at 40 °C) and 2-EtH esters viscosities (20.94-24.44 cSt at 40 °C) exhibited viscosities in the range of ISO VG 320 and 22 respectively with good viscosity indices. Acylated NPG esters were found suitable for high temperature and acylated 2-ethylhexyl esters for low viscosity grade industrial applications. It was observed that the thermo-oxidative stabilities of all acylated products were found better compared to other vegetable oil based base stocks. Overall, all the sal fat based lubricant base stocks are promising candidates with a wide range of properties, which can replace most of the mineral oil base stocks with appropriate formulations.

  15. Phthalate esters in main source water and drinking water of Zhejiang Province (China): Distribution and health risks.

    Science.gov (United States)

    Wang, Xiaofeng; Lou, Xiaoming; Zhang, Nianhua; Ding, Gangqiang; Chen, Zhijian; Xu, Peiwei; Wu, Lizhi; Cai, Jianmin; Han, Jianlong; Qiu, Xueting

    2015-10-01

    To evaluate the distributions and health risks of phthalate esters in the main source water and corresponding drinking water of Zhejiang Province, the concentrations of 16 phthalate esters in water samples from 19 sites were measured from samples taken in the dry season and wet season. The concentration of the total phthalate ester congeners in source water ranged from 1.07 μg/L to 7.12 μg/L in the wet season, from 0.01 μg/L to 1.58 μg/L in the dry season, from 1.18 μg/L to 15.28 μg/L from drinking water in the wet season, and from 0.16 μg/L to 1.86 μg/L from drinking water in the dry season. Of the 16 phthalate esters, dimethyl phthalate, dibutyl phthalate, di-(2-ethyl-hexyl) phthalate, di-iso-butyl phthalate, bis-2-n-butoxyethyl phthalate, and dicyclohexyl phthalate were present in the samples analyzed, dominated by di-iso-butyl phthalate and di-(2-ethyl-hexyl) phthalate. The concentrations of phthalate esters in the wet season were all relatively higher than those in the dry season, and the drinking water had higher concentrations of phthalate esters than source water. The phthalate ester congeners studied pose little health risk to nearby citizens. Environ Toxicol Chem 2015;34:2205-2212. © 2015 SETAC. © 2015 SETAC.

  16. Effect of Silicon Substitution on the Crystal Properties of Cyanate Ester Monomers (Briefing Charts)

    Science.gov (United States)

    2015-08-17

    unlimited.   Outline • Background / Motivation – Cyanate esters – Reasons for incorporating silicon into thermosetting resins • Cyanate esters with...Approved for public release; distribution is unlimited.   The Use of Si in Thermosetting Polymers • In addition to the expected increase in short

  17. Analysis of wax esters by silver-ion high-performance liquid chromatography-tandem mass spectrometry

    Czech Academy of Sciences Publication Activity Database

    Vrkoslav, Vladimír; Urbanová, Klára; Háková, Martina; Cvačka, Josef

    2013-01-01

    Roč. 1302, Aug 9 (2013), s. 105-110 ISSN 0021-9673 R&D Projects: GA ČR GA203/09/0139 Institutional support: RVO:61388963 Keywords : jojoba * human hair * wax esters * mass spectrometry * silver-ion liquid chromatography * long-chain esters Subject RIV: CB - Analytical Chemistry, Separation Impact factor: 4.258, year: 2013

  18. Lupeol and its esters: NMR, powder XRD data and in vitro evaluation of cancer cell growth

    Directory of Open Access Journals (Sweden)

    Aline Teixeira Maciel e Silva

    2018-02-01

    Full Text Available ABSTRACT The triterpene lupeol (1 and some of its esters are secondary metabolites produced by species of Celastraceae family, which have being associated with cytotoxic activity. We report herein the isolation of 1, the semi-synthesis of eight lupeol esters and the evaluation of their in vitro activity against nine strains of cancer cells. The reaction of carboxylic acids with 1 and DIC/DMAP was used to obtain lupeol stearate (2, lupeol palmitate (3 lupeol miristate (4, and the new esters lupeol laurate (5, lupeol caprate (6, lupeol caprilate (7, lupeol caproate (8 and lupeol 3’,4’-dimethoxybenzoate (9, with high yields. Compounds 1-9 were identified using FT-IR, 1H, 13C-NMR, CHN analysis and XRD data and were tested in vitro for proliferation of human cancer cell activity. In these assays, lupeol was inactive (GI50> 250µg/mL while lupeol esters 2 -4 and 7 - 9 showed a cytostatic effect. The XRD method was a suitable tool to determine the structure of lupeol and its esters in solid state. Compound 3 showed a selective growth inhibition effect on erythromyeloblastoid leukemia (K-562 cells in a concentration-dependent way. Lupeol esters 4 and 9 showed a selective cytostatic effect with low GI50 values representing promising prototypes for the development of new anticancer drugs.

  19. Poly(ortho esters)--from concept to reality.

    Science.gov (United States)

    Heller, Jorge; Barr, John

    2004-01-01

    The development of poly(ortho esters) dates back to the early 1970s, and during that time, four distinct families were developed. These polymers can be prepared by a transesterification reaction or by the addition of polyols to diketene acetals, and it is the latter method that has proven to be preferred one. The latest polymer, now under intense development, incorporates a latent acid segment in the polymer backbone that takes advantage of the acid-labile nature of the ortho ester linkages and allows control over erosion rates. By use of diols having selected chain flexibility, polymers that range from hard, brittle materials to materials that have a gel-like consistency at room temperature can be obtained. Drug release from solid materials will be illustrated with 5-fluorouacil and bovine serum albumin, and drug release from gel-like materials will be illustrated with mepivacaine, now in Phase II clinical trials as a delivery system to treat post-operative pain. A brief summary of preclinical toxicology studies is also presented.

  20. Production of Methyl Laurate from Coconut Cream through Fractionation of Methyl Ester

    Directory of Open Access Journals (Sweden)

    Johnner P. Sitompul

    2015-10-01

    Full Text Available This paper concerns the production of methyl laurate from coconut cream through fractionation of methyl esters. Coconut oil was produced by wet processing of coconut cream. The esters were prepared by reacting coconut oil and methanol using homogeneous catalyst KOH in a batch reactor, followed by fractionation of fatty acid methyl esters (FAME at various reduced pressures applying differential batch vacuum distillation. Experimental data were compared with simulation of a batch distillation employing the simple Raoult’s model and modified Raoult’s model of phase equilibria. Activity coefficients (γi were determined by optimization to refine the models. The modified Rault’s model with activity coefficients gave better agreement with the experimental data, giving the value of γi between 0,56-0,73. For a given boiling temperature, lower operating pressure produced higher purity of C10 and C12 FAME for respective distillates.

  1. Metabolism of dietary fatty alcohol, fatty acid, and wax ester in carp

    International Nuclear Information System (INIS)

    Mankura, Mitsumasa; Kayama, Mitsu; Iijima, Noriaki.

    1987-01-01

    Lipids in various tissues of the carp, Cyprinus carpio were analyzed. The fates of force-fed [1- 14 C]palmitic acids, [1- 14 C]cetyl alcohol, and oleyl[1- 14 C]linoleate, were compared with those given in vitro experiments. Major lipid classes in all except adipose tissue were found to be polar lipids (phospholipids) and triacylglycerols. The major fatty acids in nearly all the tissues were 16 : 0, 18 : 1, 18 : 2, and 22 : 6. Although the radioactivity incorporation into wax esters from [1- 14 C]palmitic acid and [1- 14 C]cetyl alcohol for various tissue homogenates was quite high, in vivo incorporation of these labelled compounds into wax esters was very low and radioactivity was distributed mainly in the lipids of muscle, skin, hepatopancreas, intestine, and gill. Almost all the radioactivity in various tissues was present in phospatidylcholine and triacylglycerols. Most of the oleyl[1- 14 C]linoleate was easily hydrolyzed by various tissue homogenates. Force-fed oleyl[1- 14 C]linoleate was hydrolyzed in the intestine and then transported to other tissues, such as muscle, kin, gill, and hepatopancreas. Moreover, released radioactivity from oleyl[1- 14 C]linoleate was present in mainly phosphatidylcholine and triacylglycerols. Radioactivity was also detected in wax esters in plasma. Certain amounts for fatty acids released from [1- 14 C]triolein in the hepatopancreas homogenates were incorporated into wax esters; this was stimulated by the addition of oleyl alcohol. The present results indicate extensive hydrolysis of wax ester to possibly occur in the intestine and certain portions of the fatty alcohol moiety to be resterfied. The portions may be oxidized to fatty acids and which subsequently behave as dietary fatty acids. (author) 50 ref

  2. The gas–liquid chromatography of carboxylic acid esters of the urinary 11-deoxy-17-oxo steroids

    Science.gov (United States)

    Sadler, Patricia A.; Kellie, A. E.

    1967-01-01

    1. The gas–liquid-chromatographic separations of the acetate, propionate, n-butyrate, isobutyrate and n-valerate esters of androsterone, aetiocholanolone and dehydroepiandrosterone were studied on a 1% neopentyl glycol sebacate column. The n-butyrate, isobutyrate and n-valerate esters were well resolved. 2. The three steroids derived from hydrolysed urinary 17-oxo steroid conjugate extracts were analysed by gas–liquid chromatography after conversion into their n-butyrate esters. The results were compared with independent determinations involving chromatography on alumina. PMID:4227802

  3. An Evaluation of Fracture Toughness of Vinyl Ester Composites Cured under Microwave Conditions

    Science.gov (United States)

    Ku, H.; Chan, W. L.; Trada, M.; Baddeley, D.

    2007-12-01

    The shrinkage of vinyl ester particulate composites has been reduced by curing the resins under microwave conditions. The reduction in the shrinkage of the resins by microwaves will enable the manufacture of large vinyl ester composite items possible (H.S. Ku, G. Van Erp, J.A.R. Ball, and S. Ayers, Shrinkage Reduction of Thermoset Fibre Composites during Hardening using Microwaves Irradiation for Curing, Proceedings, Second World Engineering Congress, Kuching, Malaysia, 2002a, 22-25 July, p 177-182; H.S. Ku, Risks Involved in Curing Vinyl Ester Resins Using Microwaves Irradiation. J. Mater. Synth. Proces. 2002b, 10(2), p 97-106; S.H. Ku, Curing Vinyl Ester Particle Reinforced Composites Using Microwaves. J. Comp. Mater., (2003a), 37(22), p 2027-2042; S.H. Ku and E. Siores, Shrinkage Reduction of Thermoset Matrix Particle Reinforced Composites During Hardening Using Microwaves Irradiation, Trans. Hong Kong Inst. Eng., 2004, 11(3), p 29-34). In tensile tests, the yield strengths of samples cured under microwave conditions obtained are within 5% of those obtained by ambient curing; it is also found that with 180 W microwave power, the tensile strengths obtained for all duration of exposure to microwaves are also within the 5% of those obtained by ambient curing. While, with 360 W microwave power, the tensile strengths obtained for all duration of exposure to microwaves are 5% higher than those obtained by ambient curing. Whereas, with 540 W microwave power, the tensile strengths obtained for most samples are 5% below those obtained by ambient curing (H. Ku, V.C. Puttgunta, and M. Trada, Young’s Modulus of Vinyl Ester Composites Cured by Microwave Irradiation: Preliminary Results, J. Electromagnet. Waves Appl., 2007, 20(14), p. 1911-1924). This project, using 33% by weight fly ash reinforced vinyl ester composite [VE/FLYSH (33%)], is to further investigate the difference in fracture toughness between microwave cured vinyl ester particulate composites and those cured

  4. Density of Jatropha curcas Seed Oil and its Methyl Esters: Measurement and Estimations

    Science.gov (United States)

    Veny, Harumi; Baroutian, Saeid; Aroua, Mohamed Kheireddine; Hasan, Masitah; Raman, Abdul Aziz; Sulaiman, Nik Meriam Nik

    2009-04-01

    Density data as a function of temperature have been measured for Jatropha curcas seed oil, as well as biodiesel jatropha methyl esters at temperatures from above their melting points to 90 ° C. The data obtained were used to validate the method proposed by Spencer and Danner using a modified Rackett equation. The experimental and estimated density values using the modified Rackett equation gave almost identical values with average absolute percent deviations less than 0.03% for the jatropha oil and 0.04% for the jatropha methyl esters. The Janarthanan empirical equation was also employed to predict jatropha biodiesel densities. This equation performed equally well with average absolute percent deviations within 0.05%. Two simple linear equations for densities of jatropha oil and its methyl esters are also proposed in this study.

  5. Derivatization of enolic OH of piroxicam: a comparative study on esters and sulfonates

    Energy Technology Data Exchange (ETDEWEB)

    Jayaselli, J.; Cheemala, J. Manila Sagar; Geetha Rani, D.P.; Pal, Sarbani [MNR Post Graduate College, Kukatpally, Hyderabad (India). Dept. of Chemistry]. E-mail: sarbani277@yahoo.com

    2008-07-01

    A number of ester and sulfonate derivatives of piroxicam were prepared via acylation/sulfonation of the enolic OH of piroxicam. All the compounds were evaluated for their chemical stability and cyclooxygenase inhibiting properties. Data suggested that esters could be useful for the development of potential prodrugs. The sulfonate derivatives prepared for the first time were found to be stable. One of them showed a moderately selective COX-2 inhibition over COX-1 and would have lower gastrointestinal side effects than piroxicam due to the masked enolic OH group. A plausible mechanism for the acylation/sulfonation process has been proposed that involves participation of the pyridine moiety of piroxicam. Molecular structure of one of the ester was established for the first time by the crystal structure analysis from X-ray powder data. (author)

  6. Derivatization of enolic OH of piroxicam: a comparative study on esters and sulfonates

    International Nuclear Information System (INIS)

    Jayaselli, J.; Cheemala, J. Manila Sagar; Geetha Rani, D.P.; Pal, Sarbani

    2008-01-01

    A number of ester and sulfonate derivatives of piroxicam were prepared via acylation/sulfonation of the enolic OH of piroxicam. All the compounds were evaluated for their chemical stability and cyclooxygenase inhibiting properties. Data suggested that esters could be useful for the development of potential prodrugs. The sulfonate derivatives prepared for the first time were found to be stable. One of them showed a moderately selective COX-2 inhibition over COX-1 and would have lower gastrointestinal side effects than piroxicam due to the masked enolic OH group. A plausible mechanism for the acylation/sulfonation process has been proposed that involves participation of the pyridine moiety of piroxicam. Molecular structure of one of the ester was established for the first time by the crystal structure analysis from X-ray powder data. (author)

  7. Capacity of ensilage of Jatropha curcas L. cake to degrade forbol esters

    Directory of Open Access Journals (Sweden)

    André Soares de Oliveira

    2012-06-01

    Full Text Available The objective of this study was to evaluate the capacity of the ensilage of Jatropha curcas L. expeller cake to reduce the phorbol esters and its effect on fermentative losses, by adding soluble carbohydrates or microbial inoculants. The design was completely randomized with four replications in a 3 × 2 factorial arrangement, with three sources of soluble carbohydrates (SC, control, 50 g sucrose/kg or 50 g crude glycerin/kg as fed and two doses of microbial inoculants (MI, 0 or 5 × 10(5 ufc Lactobacillus plantarum + 3.33 × 10(5 ufc Propionibacterium per g as fed. Twenty-four mini-silos (982 cm³ of polyvinyl chloride were created and opened after 60 days of fermentation at room temperature. The pre-hydrated Jatropha curcas L. cake (282 g of water/kg contained 0.424 mg of phorbol esters/g of dry matter. Ensiling reduced the phorbol esters in 47.4%, on average, regardless of the SC or MI. There was no interaction effect between SC and MI on effluent, gases or total dry matter losses. However, both losses were increased when SC were added, and it was higher with glycerin that than sucrose. The addition of MI reduced all fermentation losses. The process of ensiling, although partially to reduce the phorbol esters of pre-hydrated Jatropha curcas L. cake, is not indicated as a biodestoxification procedure.

  8. Stability and changes in astaxanthin ester composition from Haematococcus pluvialis during storage

    Science.gov (United States)

    Miao, Fengping; Geng, Yahong; Lu, Dayan; Zuo, Jincheng; Li, Yeguang

    2013-11-01

    In this paper, we investigated the effects of temperature, oxygen, antioxidants, and corn germ oil on the stability of astaxanthin from Haematococcus pluvialis under different storage conditions, and changes in the composition of astaxanthin esters during storage using high performance liquid chromatography and spectrophotometry. Oxygen and high temperatures (22-25°C) significantly reduced the stability of astaxanthin esters. Corn germ oil and antioxidants (ascorbic acid and vitamin E) failed to protect astaxanthin from oxidation, and actually significantly increased the instability of astaxanthin. A change in the relative composition of astaxanthin esters was observed after 96 weeks of long-term storage. During storage, the relative amounts of free astaxanthin and astaxanthin monoesters declined, while the relative amount of astaxanthin diesters increased. Thus, the ratio of astaxanthin diester to monoester increased, and this ratio could be used to indicate if astaxanthin esters have been properly preserved. If the ratio is greater than 0.2, it suggests that the decrease in astaxanthin content could be higher than 20%. Our results show that storing algal powder from H. pluvialis or other natural astaxanthin products under vacuum and in the dark below 4°C is the most economical and applicable storage method for the large-scale production of astaxanthin from H. pluvialis. This storage method can produce an astaxanthin preservation rate of at least 80% after 96 weeks of storage.

  9. Enzymatic synthesis of arbutin undecylenic acid ester and its inhibitory effect on mushroom tyrosinase.

    Science.gov (United States)

    Tokiwa, Y; Kitagawa, M; Raku, T

    2007-03-01

    A novel tyrosinase inhibitor, an arbutin derivative having undecylenic acid at the 6-position of its glucose moiety, was enzymatically synthesized. Its inhibitory activity was studied in vitro by using catechol and phenol as substrates. The IC(50) value of the arbutin ester on tyrosinase using catechol (4 x 10(-4) M) was 1% of that when arbutin (4 x 10(-2) M) was used. Using phenol, IC(50) of the arbutin ester (3 x 10(-4) M) as substrate was 10% of that of arbutin (3 x 10(-3) M). These results suggest that the arbutin ester inhibits the latter part of the tyrosinase reaction, which consists of hydroxylation and oxidation.

  10. CONTAINER TERMINALS IN EUROPE

    Directory of Open Access Journals (Sweden)

    Bart W. WIEGMANS

    2001-01-01

    Full Text Available This paper aims to address the linkage between logistics (in particular, the management of marketing channel flows and transport markets, while also the interaction between these two markets and intermodal container terminals is analysed. The marketing channel theory is used to describe all relevant actors and flows that run through marketing channels, starting with customer needs and ending with customer satisfaction. Porter's theory of competitive advantages is used to review competitive forces in both markets. Finally, a competitor analysis is performed for the logistics and transport market. These theories are applied so as to be able to determine the competitive position of intermodal container terminals with a view to the management of marketing channel flows and the physical transport of freight flows. Hence, the central question of this paper is: Which markets are served by intermodal container terminals and with whom are they competing? At present, neither the maritime container terminals nor the continental container terminals appear to have a significant influence in the logistics service market; they concentrate mainly on the physical movement of containers (transshipment. Furthermore, maritime container terminals and continental container terminals are not dominant players in the transport service market. Our conclusion is that continental terminals are predominantly competing with unimodal road transport, with neighbouring continental terminals and with barge transport companies.

  11. Rapid and simple micromethod for the simultaneous determination of 3-MCPD and 3-MCPD esters in different foodstuffs.

    Science.gov (United States)

    Küsters, Markus; Bimber, Ute; Ossenbrüggen, Alexandra; Reeser, Sebastian; Gallitzendörfer, Rainer; Gerhartz, Michael

    2010-06-09

    This paper describes for the first time a micromethod for the simultaneous determination of 3-monochloropropane-1,2-diol (3-MCPD) and fatty acid esters of 3-MCPD (3-MCPD esters) in different foodstuffs. 3-MCPD and 3-MCPD esters were isolated from food products using a single extraction step separating hydrophilic and lipophilic compounds. An aliquot of the aqueous layer was analyzed for the content of 3-MCPD while a part of the organic layer was analyzed for 3-MCPD esters after cleavage with sodium methoxide. After a simple derivatization procedure with phenylboronic acid (PBA), the determination was achieved by isotope dilution GC-MS using isotope-labeled 3-MCPD and 3-MCPD ester as internal standards. The method was validated for various foodstuffs like bakery products, meat and fish products, and soups as well as seasonings with LOD of 1-2 microg/kg (3-MCPD) and 6 microg/kg (3-MCPD esters), respectively. Recoveries ranged within 95 +/- 9% and 96 +/- 10% at spiking levels of 15 and 25 microg/kg in all matrices for 3-MCPD and 84 +/- 9% and 85 +/- 7% at spiking levels of 0.05 mg/kg and 2 mg/kg for 3-MCPD esters. The method avoids tedious and laborious sample preparation and was successfully applied to the rapid screening of samples conforming to the EU performance criteria for methods of analysis for 3-MCPD.

  12. [Development of gas chromatography-mass spectrometry for determination of fatty acid esters of chloropropanols in milk powder and the pollution level of infant formula].

    Science.gov (United States)

    Li, Shan; Miao, Hong; Cui, Xia; Zhao, Yunfeng; Wu, Yongning

    2015-06-01

    To establish a method for determination of fatty acid esters of chloropropanols (chloropropanols esters) in milk powder by isotope dilution-gas chromatography-mass spectrometry (GC-MS), and to acquire the pollution level of chloropropanols esters in infant formula and evaluate the dietary exposure risk of chloropropanols esters in infant formula for infants. A total of 111 infant formula samples were collected from supermarkets in Beijing, and the infant formula with no chloropropanols esters detected was served as the blank sample. The samples were ultrasonically extracted with hexane, followed by ester-bond cleavage reaction with sodium methylate-methanol and purification by matrix solid-supported liquid-liquid extraction, then being derivatived with heptafluoro butyrylimidazol. After extracted by sodium chloride solution, the derivatives were determined by GC-MS. The concentration of chloropropanols esters were quantified using the deuterium chloropropanols esters as the internal standards. The accuracy of the method was assessed by the recoveries of the blank spiked samples, and the relative standard deviations (RSD) of the recoveries represent the precision of the method. The contamination level of chloropropanols esters and the intake amount of the infant formula of the 6-month infant were used to estimate the dietary exposure assessment, and x (95% CI) and P97.5 of the contamination level of chloropropanols esters were used to represent the average dietary exposure and the high-end dietary exposure. The satisfied linear correlations in the range of 0.010-0.800 mg/L was acquired for 3-MCPD esters, 2-MCPD esters, 1,3-DCP esters and 2,3-DCP esters with coefficient correlations of 0.999 9, 0.999 8, 0.999 5 and 0.999 6, respectively. The limits of detection (LOD) and the limits of quantitation (LOQ) for 3-MCPD esters, 2-MCPD esters, 1,3-DCP esters and 2,3-DCP esters were 0.005, 0.005, 0.015, 0.015 mg/kg, and 0.015, 0.015, 0.045, 0.045 mg/kg. The average

  13. Diorganotin(IV) Complexes with Methionine Methyl Ester. Equilibria ...

    African Journals Online (AJOL)

    IV) (DBT) and diphenyltin(IV) (DPT) was investigated at 25 °C and 0.1 mol dm–3 ionic strength in water for dimethyltin(IV) and in 50 % dioxane–water mixture for dibutyltin(IV) and diphenyltin(IV). Methionine methyl ester forms1:1 and 1:2 ...

  14. Ester carbonyl vibration as a sensitive probe of protein local electric field.

    Science.gov (United States)

    Pazos, Ileana M; Ghosh, Ayanjeet; Tucker, Matthew J; Gai, Feng

    2014-06-10

    The ability to quantify the local electrostatic environment of proteins and protein/peptide assemblies is key to gaining a microscopic understanding of many biological interactions and processes. Herein, we show that the ester carbonyl stretching vibration of two non-natural amino acids, L-aspartic acid 4-methyl ester and L-glutamic acid 5-methyl ester, is a convenient and sensitive probe in this regard, since its frequency correlates linearly with the local electrostatic field for both hydrogen-bonding and non-hydrogen-bonding environments. We expect that the resultant frequency-electric-field map will find use in various applications. Furthermore, we show that, when situated in a non-hydrogen-bonding environment, this probe can also be used to measure the local dielectric constant (ε). For example, its application to amyloid fibrils formed by Aβ(16-22) revealed that the interior of such β-sheet assemblies has an ε value of approximately 5.6. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Synthesis of sulfur-containing lubricant additives on the basis of fatty acid ethyl esters

    Directory of Open Access Journals (Sweden)

    Iurii S. Bodachivskyi

    2016-12-01

    Full Text Available The study reveals an energy-, resource- and eco-friendly method for preparation of sulfur-containing lubricant additives via interaction of fatty acid ethyl esters of rapeseed oil with elemental sulfur. The structure of synthesized compounds under various reactants ratio (5–50 wt.% of sulfur, duration (30–240 min and temperature of the process (160–215°С was investigated using various analytical techniques. According to the established data, aside from addition to double bonds, the side reaction of hydrogen substitution at α-methylene groups near these bonds occurs and induces the formation of conjugated systems and chromophoric sulfur-rich derivatives. Also, we found that increase of process duration evokes growth of polysulfane chains, in contrast to the raise of temperature, which leads to the formation of sulfur-containing heterocycles and hydrogen sulfide, as a result of elimination. Influence of accelerators on sulfurization of fatty acid ethyl esters was also examined. The most effective among them are mixtures of zinc dibutyldithiocarbamate with zinc oxide or stearic acid, which soften synthesis conditions and doubly decrease duration of the high-temperature stage. In addition, sulfur-containing compositions of ethyl esters and α-olefins, vulcanized esters by benzoyl peroxide, nonylphenols and zinc dinonylphenyldithiophosphate were designed. The study identified that lithium lubricant with sulfurized vulcanized esters provides improved tribological properties, in comparison with base lubricant or lubricant with the non-modified product.

  16. Pivotal role of water in terminating enzymatic function: a density functional theory study of the mechanism-based inactivation of cytochromes P450.

    Science.gov (United States)

    Hirao, Hajime; Cheong, Zhi Hao; Wang, Xiaoqing

    2012-07-12

    The importance of the mechanism-based inactivation (MBI) of enzymes, which has a variety of physiological effects and therapeutic implications, has been garnering appreciation. Density functional theory calculations were undertaken to gain a clear understanding of the MBI of a cytochrome P450 enzyme (CYP2B4) by tert-butylphenylacetylene (tBPA). The results of calculations suggest that, in accordance with previous proposals, the reaction proceeds via a ketene-type metabolic intermediate. Once an oxoiron(IV) porphyryn π-cation radical intermediate (compound I) of P450 is generated at the heme reaction site, ketene formation is facile, as the terminal acetylene of tBPA can form a C-O bond with the oxo unit of compound I with a relatively low reaction barrier (14.1 kcal/mol). Unexpectedly, it was found that the ketene-type intermediate was not very reactive. Its reaction with the hydroxyl group of a threonine (Thr302) to form an ester bond required a substantial barrier (38.2 kcal/mol). The high barrier disfavored the mechanism by which these species react directly. However, the introduction of a water molecule in the reaction center led to its active participation in the reaction. The water was capable of donating its proton to the tBPA molecule, while accepting the proton of threonine. This water-mediated mechanism lowered the reaction barrier for the formation of an ester bond by about 20 kcal/mol. Therefore, our study suggests that a water molecule, which can easily gain access to the threonine residue through the proton-relay channel, plays a critical role in enhancing the covalent modification of threonine by terminal acetylene compounds. Another type of MBI by acetylenes, N-alkylation of the heme prosthetic group, was less favorable than the threonine modification pathway.

  17. Tropanol esters of metallocene carboxylic acids. Syntheses, labelling with 103Ru and sup(103m)Rh and organ distribution

    International Nuclear Information System (INIS)

    Wenzel, M.; Wu, Y.

    1988-01-01

    The tropanol esters of the carboxylic acids of ferrocene, 103 Ru-ruthenocene and sup(103m)Rh-rhodocinium were synthezised. The organ distribution of the 103 Ru or sup(103m)Rh labelled tropanol-esters were investigated. Only the 103 Ru labelled ester showed a high heart/blood ratio. (author)

  18. Visual communication and terminal equipment

    International Nuclear Information System (INIS)

    Kang, Cheol Hui

    1988-06-01

    This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

  19. Visual communication and terminal equipment

    Energy Technology Data Exchange (ETDEWEB)

    Kang, Cheol Hui

    1988-06-15

    This book is divided two parts about visual communication and terminal equipment. The first part introduces visual communication, which deals with foundation of visual communication, technique of visual communication, equipment of visual communication, a facsimile and pictorial image system. The second part contains terminal equipment such as telephone, terminal equipment for data transmission on constitution and constituent of terminal equipment for data transmission, input device and output device, terminal device and up-to-date terminal device.

  20. Production of novel "functional oil" rich in diglycerides and phytosterol esters with "one-pot" enzymatic transesterification.

    Science.gov (United States)

    Zheng, Ming-Ming; Huang, Qing; Huang, Feng-Hong; Guo, Ping-Mei; Xiang, Xia; Deng, Qian-Chun; Li, Wen-Lin; Wan, Chu-Yun; Zheng, Chang

    2014-06-04

    Diglycerides and phytosterol esters are two important functional lipids. Phytosterol esters mixed with dietary diglyceride could not only influence body weight but also prevent or reverse insulin resistance and hyperlipidemia. In this study, a kind of novel "functional oil" rich in both diglycerides and phytosterol esters was prepared with "one-pot" enzymatic transesterification. First, lipase AYS (Candida rugosa) was immobilized on the porous cross-linked polystyrene resin beads (NKA) via hydrophobic interaction. The resulting immobilized AYS showed much better transesterification activity and thermal stability to freeways. On the basis of the excellent biocatalyst prepared, a method for high-efficiency enzymatic esterification of phytosterols with different triglycerides to produce corresponding functional oils rich in both diglycerides and phytosterol esters was developed. Four functional oils rich in both diglycerides and phytosterol esters with conversions >92.1% and controllable fatty acid composition were obtained under the optimized conditions: 80 mmol/L phytosterols, 160 mmol/L triglycerides, and 25 mg/mL AYS@NKA at 180 rpm and 50 °C for 12 h in hexane. The prepared functional oil possessed low acid value (≤1.0 mgKOH/g), peroxide value (≤2.1 mmol/kg), and conjugated diene value (≤1.96 mmol/kg) and high diglyceride and phytosterol ester contents (≥10.4 and ≥20.2%, respectively). All of the characteristics favored the wide application of the functional oil in different fields of functional food.

  1. Production of both esters and biogas from Mexican poppy

    African Journals Online (AJOL)

    AJL

    scale industries and agricultural farms. Key words: Transestrification, energy conservation, anaerobic digestion, methane, biogas, methyl ester. INTRODUCTION. For advancement of civilization and socioeconomic developmental progress, the world is dependent on various energy resources like petrochemicals, coal,.

  2. Shank otsustab lahkumise pärast puhkuselt naasmist / Ester Shank

    Index Scriptorium Estoniae

    Šank, Ester, 1956-

    2002-01-01

    Välismaal oma korralist suvepuhkust veetev presidendi pressinõunik Ester Shank ei kinnita riigiametnike ringkondades levivaid kuuldusi, mille kohaselt on ta juba langetanud otsuse Kadrioru lossist lahkuda

  3. Determination of 4-Chloroindole-3-Acetic Acid Methyl Ester in Lathyrus Vicia and Pisum by Gas Chromatography - Mass Spectrometry

    DEFF Research Database (Denmark)

    Engvild, Kjeld Christensen; Egsgaard, Helge; Larsen, Elfinn

    1980-01-01

    4-Chloroindole-3-acetic acid methyl ester was identified unequivocally in Lathyrus latifolius L., Vicia faba L. and Pisum sativum L. by thin layer chromatography, gas chromatography and mass spectrometry. The gas chromatographic system was able to separate underivatized chloroindole-3-acetic acid...... methyl ester isomers. The quantitative determination of 4-chloroindole-3-acetic acid methyl ester in immature seeds of these three species was performed by gas chromatography – mass spectrometry using deuterium labelled 4-chloro-indole-3-acetic acid methyl ester as an internal standard. P. sativum...

  4. ENZYMATIC PRODUCTION OF ETHYL OLEATE ESTER USING A LIPASE FROM CANDIDA ANTARCTICA B

    Directory of Open Access Journals (Sweden)

    N. Sampaio Neta

    2012-05-01

    Full Text Available Lipases are biocatalysts of great importance in different areas, being able to catalyze reactions in aqueous or organic media. Furthermore, these enzymes are capable of using several substrates being stable in a wide range of pH and temperatures. Lipases promote the esterification between fatty acids and ethanol producing oleate esters. The aim of this work is to produce ethyl oleate ester by enzymatic esterification of oleic acid with ethanol. A lipase from Candida antarctica type B was used at a temperature of 55 °C. The reaction was conducted using oleic acid, sodium sulfate anhydrous, lipase and ethanol, with a ratio of oleic acid (0.03 mol or 10 ml, lipase (0.1 mol or 0.01 g, sodium sulfate anhydrous (5 g and ethanol 99 % (100 ml. Several reaction times were studied, namely 48, 72, 96 and 120 hours. Nuclear Magnetic Resonance (1H and 13C and Infrared spectra confirmed the production of ethyl oleate ester for the studied conditions. The highest ethyl oleate production yield was obtained for 96 hours reaction time. Ethyl oleate esters have been reported to possess interesting applications in several industrial fields, such as food, aromatics, cosmetics, detergents, flavors and pharmaceuticals.

  5. Studies on sterol-ester hydrolase from Fusarium oxysporum. I. Partial purification and properties.

    Science.gov (United States)

    Okawa, Y; Yamaguchi, T

    1977-05-01

    1. A search for a long chain fatty acyl sterol-ester hydrolase in microorganisms led to the isolation from soil of five strains belonging to Fusarium sp. which produced strong activity in the culture medium. 2. The cholesterol esterase from Fusarium oxysporum IGH-2 was purified about 270-fold by means of CaCl2 precipitation and Sephadex G-75 column chromatography. 3. The cholesterol esterase was activated by adekatol and Triton X-100. It was inhibited by lecithin and lysolecithin, and completely inactivated by heat treatment (60 degrees C for 30 min, at pH 7.0). 4. The optimum pH of the enzyme was found to be around 7.0. 5. Among various cholesterol esters tested, cholesterol linoleate was the most suitable substrate. 6. Cholesterol esters in serum were also hydrolyzed by this enzyme.

  6. Final report of the safety assessment of methacrylate ester monomers used in nail enhancement products.

    Science.gov (United States)

    2005-01-01

    Methacrylate ester monomers are used in as artificial nail builders in nail enhancement products. They undergo rapid polymerization to form a hard material on the nail that is then shaped. While Ethyl Methacrylate is the primary monomer used in nail enhancement products, other methacrylate esters are also used. This safety assessment addresses 22 other methacrylate esters reported by industry to be present in small percentages as artificial nail builders in cosmetic products. They function to speed up polymerization and/or form cross-links. Only Tetrahydrofurfuryl Methacrylate was reported to the FDA to be in current use. The polymerization rates of these methacrylate esters are within the same range as Ethyl Methacrylate. While data are not available on all of these methacrylate esters, the available data demonstrated little acute oral, dermal, or i.p. toxicity. In a 28-day inhalation study on rats, Butyl Methacrylate caused upper airway irritation; the NOAEL was 1801 mg/m3. In a 28-day oral toxicity study on rats, t-Butyl Methacrylate had a NOAEL of 20 mg/kg/day. Beagle dogs dosed with 0.2 to 2.0 g/kg/day of C12 to C18 methacrylate monomers for 13 weeks exhibited effects only in the highest dose group: weight loss, emesis, diarrhea, mucoid feces, or salivation were observed. Butyl Methacrylate (0.1 M) and Isobutyl Methacrylate (0.1 M) are mildly irritating to the rabbit eye. HEMA is corrosive when instilled in the rabbit eye, while PEG-4 Dimethacrylate and Trimethylolpropane Trimethacrylate are minimally irritating to the eye. Dermal irritation caused by methacrylates is documented in guinea pigs and rabbits. In guinea pigs, HEMA, Isopropylidenediphenyl Bisglycidyl Methacrylate, Lauryl Methacrylate, and Trimethylolpropane Trimethacrylate are strong sensitizers; Butyl Methacrylate, Cyclohexyl Methacrylate, Hexyl Methacrylate, and Urethane Methacrylate are moderate sensitizers; Hydroxypropyl Methacrylate is a weak sensitizer; and PEG-4 Dimethacrylate and

  7. Emissions from diesel engines using fatty acid methyl esters from different vegetable oils as blends and pure fuel

    International Nuclear Information System (INIS)

    Schröder, O; Munack, A; Schaak, J; Pabst, C; Schmidt, L; Bünger, J; Krahl, J

    2012-01-01

    Biodiesel is used as a neat fuel as well as in blends with mineral diesel fuel. Because of the limited availability of fossil resources, an increase of biogenic compounds in fuels is desired. To achieve this goal, next to rapeseed oil, other sustainably produced vegetable oils can be used as raw materials. These raw materials influence the fuel properties as well as the emissions. To investigate the environmental impact of the exhaust gas, it is necessary to determine regulated and non-regulated exhaust gas components. In detail, emissions of aldehydes and polycyclic aromatic hydrocarbons (PAH), as well as mutagenicity in the Ames test are of special interest. In this paper emission measurements on a Euro III engine OM 906 of Mercedes-Benz are presented. As fuel vegetable oil methyl esters from various sources and reference diesel fuel were used as well as blends of the vegetable oil methyl esters with diesel fuel. PAH were sampled according to VDI Guideline 3872. The sampling procedure of carbonyls was accomplished using DNPH cartridges coupled with potassium iodide cartridges. The carbon monoxide and hydrocarbon emissions of the tested methyl esters show advantages over DF. The particle mass emissions of methyl esters were likewise lower than those of DF, only linseed oil methyl ester showed higher particle mass emissions. A disadvantage is the use of biodiesel with respect to emissions of nitrogen oxides. They increased depending on the type of methyl ester by 10% to 30%. Emissions of polycyclic aromatic hydrocarbons (PAHs) and the results of mutagenicity tests correlate with those of the PM measurements, at which for palm oil methyl ester next to coconut oil methyl ester the lowest emissions were detected. From these results one can formulate a clear link between the iodine number of the ester and the emission behaviour. For blends of biodiesel and diesel fuel, emissions changed linearly with the proportion of biodiesel. However, especially in the non

  8. VALIDASI MODIFIKASI METODE WEIßHAAR UNTUK ANALISIS 3-MCPD ESTER DALAM MINYAK GORENG SAWIT [Validation of Modified Weißhaar’s Method for 3-MCPD Esters Analysis in Palm Oil

    Directory of Open Access Journals (Sweden)

    Tanti Lanovia1,2*

    2014-12-01

    Full Text Available The 3-monochloropropane-1,2-diol (3-MCPD and 3-MCPD esters were found in any type of refined vegetable oil -mostly produced during the refining process- and recognized as emerging food contaminants. Several analytical methods have been developed and one of which was a Weißhaar's method. The study aims to validate the modified Weißhaar's method for analysis of 3-MCPD and 3-MCPD esters in refined palm oil. Ion fragments were used for identification and quantification of 3-MCPD and 3-MCPD-d5. 3-MCPD was determined by GC-MS after released from its ester by transesterification with sodium methoxide and derivatized with phenylboronic acid. The validation showed that liniarity response (r=0.994 was observed from a linear regression by using external standard and internal standard at a concentration range of 0.008 and 0.377 µg mL-1. The LOD of the validated method was 0.06 µg g-1 while its LOQ was 0.20 µg g-1, precision (relative standard deviation, RSD was 6.16%, and accuracy (as percentage of recovery was in the range of 95.83-113.27%. This results indicated that the modified method was valuable and sensitive for detection of 3-MCPD and 3-MCPD esters. Using the validated method, 3-MCPD esters content of a commercial palm oil sample was determined and calculated as the difference between total 3-MCPD and free 3-MCPD, which was 13.24 µg g-1. Total 3-MCPD content of several palm oils were at a concentration range of 13.94-34.52 µg g-1. These results also showed that there was a correlation between 3-MCPD with diacylglyceride (DAG. Samples with DAG content gave a high test results of 3-MCPD with a coefficient of correlation of r=0.752.

  9. An alternative procedure for incorporating radiolabelled cholesteryl ester into human plasma lipoproteins in vitro

    International Nuclear Information System (INIS)

    Roberts, D.C.K.; Miller, N.E.; Price, S.G.L.; Crook, D.; Cortese, C.; Ville, A. La; Masana, L.; Lewis, B.

    1985-01-01

    A simple method has been developed for labelling human plasma lipoproteins to high specific radioactivity with radioactive cholesteryl esters in vitro. After isolation by preparative ultracentrifugation, the selected lipoprotein was incubated for 30 min at 4 0 C in human serum (d > 1.215) that had been prelabelled with [4- 14 C]cholesteryl oleate or [1,2- 3 H]cholesteryl linoleate, and was then re-isolated by ultracentrifugation. All major lipoprotein classes were labelled by the procedure. Specific radioactivities of up to 18 d.p.m. .pmol -1 (46d.p.m. .ng -1 ) were achieved. When radiolabelled high-density lipoprotein was infused intravenously, the radioactive cholesteryl ester behaved in vivo indistinguishably from endogenous cholesteryl esters produced by the lecithin (phosphatidylcholine): cholesterol acyltransferase reaction. (author)

  10. Investigations on mechanical and two-body abrasive wear behaviour of glass/carbon fabric reinforced vinyl ester composites

    International Nuclear Information System (INIS)

    Suresha, B.; Kumar, Kunigal N. Shiva

    2009-01-01

    The aim of the research article is to study the mechanical and two-body abrasive wear behaviour of glass/carbon fabric reinforced vinyl ester composites. The measured wear volume loss increases with increase in abrading distance/abrasive particle size. However, the specific wear rate decreases with increase in abrading distance and decrease in abrasive particle size. The results showed that the highest specific wear rate is for glass fabric reinforced vinyl ester composite with a value of 10.89 x 10 -11 m 3 /Nm and the lowest wear rate is for carbon fabric reinforced vinyl ester composite with a value of 4.02 x 10 -11 m 3 /Nm. Mechanical properties were evaluated and obtained values are compared with the wear behaviour. The worn surface features have been examined using scanning electron microscope (SEM). Photomicrographs of the worn surfaces revealed higher percentage of broken glass fiber as compared to carbon fiber. Also better interfacial adhesion between carbon and vinyl ester in carbon reinforced vinyl ester composite was observed.

  11. Carboxylesterase activities toward pesticide esters in crops and weeds.

    Science.gov (United States)

    Gershater, Markus; Sharples, Kate; Edwards, Robert

    2006-12-01

    Proteins were extracted from maize, rice, sorghum, soybean, flax and lucerne; the weeds Abutilon theophrasti, Echinochloa crus-galli, Phalaris canariensis, Setaria faberii, Setaria viridis, Sorghum halepense and the model plant Arabidopsis thaliana and assayed for carboxylesterase activity toward a range of xenobiotics. These included the pro-herbicidal esters clodinafop-propargyl, fenoxaprop-ethyl, fenthioprop-ethyl, methyl-2,4-dichlorophenoxyacetic acid (2,4-d-methyl), bromoxynil-octanoate, the herbicide-safener cloquintocet-mexyl and the pyrethroid insecticide permethrin. Highest activities were recorded with alpha-naphthyl acetate and methylumbelliferyl acetate. Esters of p-nitrophenol were also readily hydrolysed, with turnover declining as the chain length of the acyl component increased. Activities determined with model substrates were much higher than those observed with pesticide esters and were of limited value in predicting the relative rates of hydrolysis of the crop protection agents. Substrate preferences with the herbicides were typically 2,4-d-methyl>clodinafop-propargyl>fenthioprop-ethyl, fenoxaprop-ethyl and bromoxynil-octanoate. Isoelectric focussing in conjunction with staining for esterase activity using alpha-naphthyl acetate as substrate confirmed the presence of multiple carboxylesterase isoenzymes in each plant, with major qualitative differences observed between species. The presence of serine hydrolases among the resolved isoenzymes was confirmed through their selective inhibition by the organophosphate insecticide paraoxon. Our studies identify potentially exploitable differences between crops and weeds in their ability to bioactivate herbicides by enzymic hydrolysis and also highlight the usefulness of Arabidopsis as a plant model to study xenobiotic biotransformation.

  12. Pramana – Journal of Physics | Indian Academy of Sciences

    Indian Academy of Sciences (India)

    Hydrophobicity-induced drying transition in alkanethiol self-assembled monolayer–water interface · V Lakshminarayanan Ujjal Kumar Sur · More Details Abstract Fulltext PDF. During the course of our investigation of the electron transfer properties of some redox species through highly hydrophobic long chain alkanethiol ...

  13. Effect of Sucrose Esters on the Physicochemical Properties of Wheat ...

    African Journals Online (AJOL)

    HP

    In addition, the structure and thermodynamic properties of the ... Journal Citation Reports/Science Edition, Directory of Open Access Journals ... functional differences between wheat starches ..... esters cosurfactant microemulsion systems for.

  14. Toxicological assessment of 3-chloropropane-1,2-diol and glycidol fatty acid esters in food.

    Science.gov (United States)

    Bakhiya, Nadiya; Abraham, Klaus; Gürtler, Rainer; Appel, Klaus Erich; Lampen, Alfonso

    2011-04-01

    Fatty acid esters of 3-chloropropane-1,2-diol (3-MCPD) and glycidol are a newly identified class of food process contaminants. They are widespread in refined vegetable oils and fats and have been detected in vegetable fat-containing products, including infant formulas. There are no toxicological data available yet on the 3-MCPD and glycidol esters, and the primary toxicological concern is based on the potential release of 3-MCPD or glycidol from the parent esters by lipase-catalyzed hydrolysis in the gastrointestinal tract. Although 3-MCPD is assessed as a nongenotoxic carcinogen with a tolerable daily intake (TDI) of 2 μg/kg body weight (bw), glycidol is a known genotoxic carcinogen, which induces tumors in numerous organs of rodents. The initial exposure estimates, conducted by Federal Institute for Risk Assessment (BfR) under the assumption that 100% of the 3-MPCD and glycidol are released from their esters, revealed especially that infants being fed commercial infant formula could ingest harmful amounts of 3-MCPD and glycidol. However, the real oral bioavailability may be lower. As this gives rise for toxicological concern, the currently available toxicological data of 3-MCPD and glycidol and their esters are summarized in this review and discussed with regard to data gaps and further research needs. Copyright © 2011 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Active Ester Containing Surfmer for One-Stage Polymer Nanoparticle Surface Functionalization in Mini-Emulsion Polymerization

    Directory of Open Access Journals (Sweden)

    Vanessa L. Albernaz

    2018-04-01

    Full Text Available Functional surface active monomers (surfmers are molecules that combine the functionalities of surface activity, polymerizability, and reactive groups. This study presents an improved pathway for the synthesis of the active ester containing surfmer p-(11-acrylamidoundecanoyloxyphenyl dimethylsulfonium methyl sulfate (AUPDS. Further, the preparation of poly(methyl methacrylate and polystyrene nanoparticles (NPs by mini-emulsion polymerization using AUPDS is investigated, leading to NPs with active ester groups on their surface. By systematically varying reaction parameters and reagent concentrations, it was found that AUPDS feed concentrations between 2–4 mol% yielded narrowly distributed and stable spherical particles with average sizes between 83 and 134 nm for non-cross-linked NPs, and up to 163 nm for cross-linked NPs. By basic hydrolysis of the active ester groups in aqueous dispersion, the positive ζ-potential (ZP was converted into a negative ZP and charge quantities determined by polyelectrolyte titrations before and after hydrolysis were in the same range, indicating that the active ester groups were indeed accessible in aqueous suspension. Increasing cross-linker amounts over 10 mol% also led to a decrease of ZP of NPs, probably due to internalization of the AUPDS during polymerization. In conclusion, by using optimized reaction conditions, it is possible to prepare active ester functionalized NPs in one stage using AUPDS as a surfmer in mini-emulsion polymerization.

  16. Quantitative analysis of anti-inflammatory and radical scavenging triterpenoid esters in evening primrose seeds.

    Science.gov (United States)

    Zaugg, Janine; Potterat, Olivier; Plescher, Andreas; Honermeier, Bernd; Hamburger, Matthias

    2006-09-06

    Lipophilic triterpenoidal esters with radical scavenging and cyclooxygenase inhibitory properties were recently found in cold-pressed, nonraffinated evening primrose oil (EPO). A quantitative assay for the analysis of 3-O-trans-caffeoyl derivatives of betulinic, morolic, and oleanolic acid in evening primrose seeds was developed and validated. Extraction efficiency >99% was achieved by means of pressurized liquid extraction with two extraction cycles and 80% (v/v) ethanol at 120 degrees C. Analysis of esters was by normal-phase high-performance liquid chromatography on a Diol column and hexane/ethyl acetate (containing 0.1% formic acid) (65:35) as the eluent. The analytes were determined without further prepurification. Seeds from defined cultures of Oenothera biennis, Oenothera lamarckiana, and Oenothera ammophila, grown under identical conditions, were analyzed. The cultures originated from seeds from eight collections in the wild and from selections from five cultivars. The content of total triterpenoidal esters in seeds varied between 1.34 and 2.78 mg/g. Three types of qualitative patterns were observed for the triterpenoidal esters. The influence of different harvest times and plant treatments was studied with the cultivar Anothera. Variations between 1.5 and 2.3 mg/g were found.

  17. Ordered self-assembled monolayers terminated with different chemical functional groups direct neural stem cell linage behaviours

    International Nuclear Information System (INIS)

    Yao, Shenglian; Liu, Xi; He, Jin; Wang, Xiumei; Wang, Ying; Cui, Fu-Zhai

    2016-01-01

    Neural stem cells (NSCs) have been a promising candidate for stem cell-based nerve tissue regeneration. Therefore, the design of idea biomaterials that deliver precise regulatory signals to control stem cell fate is currently a crucial issue that depends on a profound understanding of the interactions between NSCs with the surrounding micro-environment. In this work, self-assembled monolayers of alkanethiols on gold with different chemical groups, including hydroxyl (−OH), amino (−NH 2 ), carboxyl (−COOH) and methyl (−CH 3 ), were used as a simple model to study the effects of surface chemistry on NSC fate decisions. Contact angle measurement and x-ray photoelectron spectroscopy (XPS) examination implied that all types of alkanethiols self-assembled on gold into a close-packed phase structure with similar molecular densities. In this study, we evaluated NSC adhesion, migration and differentiation in response to different chemical functional groups cultured under serum-free conditions. Our studies showed that NSCs exhibited certain phenotypes with extreme sensitivity to surface chemical groups. Compared with other functional groups, the SAMs with hydroxyl end-groups provided the best micro-environment in promoting NSC migration and maintaining an undifferentiated or neuronal differentiation state.  −NH 2 surfaces directed neural stem cells into astrocytic lineages, while NSCs on  −COOH and  −CH 3 surfaces had a similar potency to differentiate into three nerve lineages. To further investigate the possible signaling pathway, the gene expression of integrin β1 and β4 were examined. The results indicated that a high expression of β1 integrin would probably have a tight correlation with the expression of nestin, which implied the stemness of NSCs, while β4 integrin seemed to correspond to the differentiated NSCs. The results presented here give useful information for the future design of biomaterials to regulate the preservation

  18. Rheological behavior, chemical and physical characterization of soybean and cottonseed methyl esters submitted to thermal oxidation process

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Adriano Sant' ana; Silva, Flavio Luiz Honorato da; Lima, Ezenildo Emanuel de; Carvalho, Maria Wilma N.C. [Universidade Federal de Campina Grande (CCT/UFCG), PB (Brazil). Centro de Ciencia e Tecnologia; Dantas, Hemeval Jales; Farias, Paulo de Almeida [Universidade Federal de Campina Grande (CTRN/UFCG), PB (Brazil). Centro de Tecnologia e Recursos Naturais

    2008-07-01

    In this study the effect of antioxidant terc-butylhydroxyanisol (BHA) on the oxidative stability of soybean and cottonseed methyl esters subjected to thermal degradation at 100 deg C was studied. Soybean and cottonseed methyl esters specific mass, dynamic viscosity and rheological behavior were evaluated. According to results, antioxidant degraded samples specific mass and dynamic viscosity did not showed alterations, remaining statistically equal. Soybean and cottonseed methyl esters showed a Newtonian rheological behavior and degraded samples without adding BHA showed rheological behavior alterations. (author)

  19. Synthesis of carbon-14-labeled sodium palmoxirate and its coenzyme A ester

    Energy Technology Data Exchange (ETDEWEB)

    Weaner, L.E.; Hoerr, D.C.

    1986-04-01

    Synthetic procedures for the preparation of carbon-14-labeled sodium palmoxirate (TDGA), labeled either in the carboxyl position or in the tetradecyl hydrocarbon chain, are described. In addition, the synthesis of the coenzyme A ester of TDGA-14C with a specific activity of 51 mCi/mmol is reported. The coenzyme A ester was prepared by formation of the acyl chloride with oxalyl chloride followed by reaction with coenzyme A (CoA) in a borate-buffered tetrahydrofuran solution. Purification methods and analytical and stability data are reported for the compounds.

  20. Efficient 'One Pot' Nitro Reduction-Protection of γ-Nitro Aliphatic Methyl Esters

    OpenAIRE

    Díaz-Coutiño, Francisco D.; Escalante, Jaime

    2009-01-01

    A simple and efficient protocol has been developed for the direct conversion of γ-nitro aliphatic methyl esters to N-(tert-butoxycarbonyl)amine methyl esters using NH4+HCO2- and Pd/C in the presence of (Boc)2O. There was a significant decrease in the reaction time under these conditions, increased yields and the purity of the products using this 'one pot' procedure. Un protocolo simple y eficiente de síntesis ha sido desarrollado para la conversión directa de metil ésteres de γ-nitro alifá...

  1. Potentiation of insulin release in response to amino acid methyl esters correlates to activation of islet glutamate dehydrogenase activity

    DEFF Research Database (Denmark)

    Kofod, Hans; Lernmark, A; Hedeskov, C J

    1986-01-01

    Column perifusion of mouse pancreatic islets was used to study the ability of amino acids and their methyl esters to influence insulin release and activate islet glutamate dehydrogenase activity. In the absence of L-glutamine, L-serine and the methyl ester of L-phenylalanine, but neither L...... glutamate dehydrogenase activity showed that only the two methyl esters of L-phenylalanine and L-serine activated the enzyme. It is concluded that the mechanism by which methyl esters of amino acids potentiate insulin release is most likely to be mediated by the activation of pancreatic beta-cell glutamate...

  2. Use of citric acid esters as alternative fuel for diesel engines

    Energy Technology Data Exchange (ETDEWEB)

    Huber, Georg; Thuneke, Klaus; Remmele, Edgar [Technologie- und Foerderzentrum, Straubing (Germany); Schieder, Doris [Technische Univ. Muenchen, Straubing (Germany). Lehrstuhl fuer Chemie Biogener Rohstoffe

    2013-06-01

    Common fuels for (adapted) diesel engines are fossil diesel fuel, fatty acid methyl ester (FAME or biodiesel) or vegetable oils. Furthermore the citric acid esters tributylcitrate (TBC) and triethylcitrate (TEC) are expected to be a possible diesel substitute. Their use as fuel was applied for a patent in Germany in 2010. According to the patent applicant the advantages are low soot combustion, independence of energy imports due to the possibility of local production and a broad raw material base. Their fuel properties have been analysed in the laboratory and compared with the relevant fuel standards. Only some of the determined values are meeting the specifications, but on the other hand few rapeseed oil characteristics (e. g. oxidation stability and viscosity) can be improved if the citric acid esters are used as a blend component. The operating and emission behaviour of a vegetable oil compatible CHP unit fuelled with various rapeseed oil and TBC blends were investigated and a trouble free and soot emission reduced engine operation due to the high molecularly bound oxygen content was observed. Long term test runs are necessary for an entire technical validation. (orig.)

  3. Curing reaction of bisphenol-A based benzoxazine with cyanate ester resin and the properties of the cured thermosetting resin

    Directory of Open Access Journals (Sweden)

    H. Kimura

    2011-12-01

    Full Text Available Curing reaction of bisphenol-A based benzoxazine with cyanate ester resin and the properties of the cured thermosetting resin were investigated. The cure behavior of benzoxazine with cyanate ester resin was monitored by model reaction using nuclear magnetic resonance (NMR. As a result of the model reaction, the ring opening reaction of benzoxazine ring and thermal self-cyclotrimerization of cyanate ester group occurred, and then the phenolic hydoroxyl group generated by the ring opening reaction of benzoxazine ring co-reacted with cyanate ester group. The properties of the cured thermosetting resin were estimated by mechanical properties, electrical resistivity, water resistance and heat resistance. The cured thermosetting resin from benzoxazine and cyanate ester resin showed good heat resistance, high electrical resistivity and high water resistance, compared with the cured thermosetting resin from benzoxazine and epoxy resin.

  4. Brain modulation of Dufour's gland ester biosynthesis in vitro in the honeybee ( Apis mellifera)

    Science.gov (United States)

    Katzav-Gozansky, Tamar; Hefetz, Abraham; Soroker, Victoria

    2007-05-01

    Caste-specific pheromone biosynthesis is a prerequisite for reproductive skew in the honeybee. Nonetheless, this process is not hardwired but plastic, in that egg-laying workers produce a queen-like pheromone. Studies with Dufour’s gland pheromone revealed that, in vivo, workers’ gland biosynthesis matches the social status of the worker, i.e., sterile workers showed a worker-like pattern whereas fertile workers showed a queen-like pattern (production of the queen-specific esters). However, when incubated in vitro, the gland spontaneously exhibits the queen-like pattern, irrespective of its original worker type, prompting the notion that ester production in workers is under inhibitory control that is queen-dependent. We tested this hypothesis by exposing queen or worker Dufour’s glands in vitro to brain extracts of queens, queenright (sterile) workers and males. Unexpectedly, worker brain extracts activated the queen-like esters biosynthesis in workers’ Dufour’s gland. This stimulation was gender-specific; queen or worker brains demonstrated a stimulatory activity, but male brains did not. Queen gland could not be further stimulated. Bioassays with heated and filtered extracts indicate that the stimulatory brain factor is below 3,000 Da. We suggest that pheromone production in Dufour’s gland is under dual, negative positive control. Under queenright conditions, the inhibitor is released and blocks ester biosynthesis, whereas under queenless conditions, the activator is released, activating ester biosynthesis in the gland. This is consistent with the hypothesis that queenright workers are unequivocally recognized as non-fertile, whereas queenless workers try to become “false queens” as part of the reproductive competition.

  5. Hydrolytic Stability of Boronate Ester-Linked Covalent Organic Frameworks

    KAUST Repository

    Li, Huifang; Li, Haoyuan; Dai, Qingqing; Li, Hong; Bredas, Jean-Luc

    2018-01-01

    by reducing the energy barrier by a factor of 3. Importantly, the hydrolysis of boronate ester bonds situated in a COF environment follows reaction pathways that are different and have increased energy barriers. These results point to an enhanced hydrolytic

  6. Structure and reactivity of boron-ate complexes derived from primary and secondary boronic esters.

    Science.gov (United States)

    Feeney, Kathryn; Berionni, Guillaume; Mayr, Herbert; Aggarwal, Varinder K

    2015-06-05

    Boron-ate complexes derived from primary and secondary boronic esters and aryllithiums have been isolated, and the kinetics of their reactions with carbenium ions studied. The second-order rate constants have been used to derive nucleophilicity parameters for the boron-ate complexes, revealing that nucleophilicity increased with (i) electron-donating aromatics on boron, (ii) neopentyl glycol over pinacol boronic esters, and (iii) 12-crown-4 ether.

  7. Antecedents of Customer Relationship Termination

    DEFF Research Database (Denmark)

    Geersbro, Jens; Ritter, Thomas

    To end business relationships, or to more actively terminate relationships, has long been acknowledged as part of customer relationship management. However, compared to other elements such as initiation and maintenance of relationships, little is known about the termination of business...... relationships as a managerial task. This paper contributes by (1) developing a conceptualization of relationship termination competence and (2) analyzing its antecedents. The empirical results identify termination acceptance, definition non-customers, organizational relationship termination routines......, and motivation as significant antecedents. Because of this, managers need to develop their organizations in order to use relationship termination as a vital strategy....

  8. Near Infrared Spectroscopic Identification of Alkyl Aromatic Esters and Phenyl Ketones

    Science.gov (United States)

    Nelyubov, D. V.; Vazhenin, D. A.; Kudriavtsev, A. A.; Buzolina, A. Yu.

    2018-03-01

    Bands characterizing the content of carbon atoms in alkyl (7177-7205 cm-1) and phenyl structural fragments (9175-9192 cm-1) in organic molecules were revealed by studying the near infrared spectra of such compounds. The optical density at the maxima of these absorption bands was shown to depend strongly on the fraction of carbon atoms in the corresponding fragments. The developed models proved to be adequate for determining the fraction of carbon atoms in alkyl aromatic esters and phenyl ketones. The feasibility of modeling the molecular structure of alkyl aromatic esters using regression models was demonstrated for the product of the condensation of oleic acid and benzyl alcohol.

  9. Synthesis and application of a triazene-ferrocene modifier for immobilization and characterization of oligonucleotides at electrodes.

    Science.gov (United States)

    Hansen, Majken N; Farjami, Elaheh; Kristiansen, Martin; Clima, Lilia; Pedersen, Steen Uttrup; Daasbjerg, Kim; Ferapontova, Elena E; Gothelf, Kurt V

    2010-04-16

    A new DNA modifier containing triazene, ferrocene, and activated ester functionalities was synthesized and applied for electrochemical grafting and characterization of DNA at glassy carbon (GC) and gold electrodes. The modifier was synthesized from ferrocenecarboxylic acid by attaching a phenyltriazene derivative to one of the ferrocene Cp rings, while the other Cp ring containing the carboxylic acid was converted to an activated ester. The modifier was conjugated to an amine-modified DNA sequence. For immobilization of the conjugate at Au or GC electrodes, the triazene was activated by dimethyl sulfate for release of the diazonium salt. The salt was reductively converted to the aryl radical which was readily immobilized at the surface. DNA grafted onto electrodes exhibited remarkable hybridization properties, as detected through a reversible shift in the redox potential of the Fc redox label upon repeated hybridization/denaturation procedures with a complementary target DNA sequence. By using a methylene blue (MB) labeled target DNA sequence the hybridization could also be followed through the MB redox potential. Electrochemical studies demonstrated that grafting through the triazene modifier can successfully compete with existing protocols for DNA immobilization through the commonly used alkanethiol linkers and diazonium salts. Furthermore, the triazene modifier provides a practical one-step immobilization procedure.

  10. pH-triggered chitosan nanogels via an ortho ester-based linkage for efficient chemotherapy.

    Science.gov (United States)

    Yang, Guanqing; Wang, Xin; Fu, Shengxiang; Tang, Rupei; Wang, Jun

    2017-09-15

    We report on new types of chitosan-based nanogels via an ortho ester-based linkage, used as drug carriers for efficient chemotherapy. First, we synthesized a novel diacrylamide containing ortho ester (OEAM) as an acid-labile cross-linker. Subsequently, methacrylated succinyl-chitosan (MASCS) was prepared and polymerized with OEAM at different molar ratios to give a series of pH-triggered MASCS nanogels. Doxorubicin (DOX) as a model anticancer drug was loaded into MASCS nanogels with a loading content of 16.5%. As expected, with the incorporation of ortho ester linkages, these nanogels showed pH-triggered degradation and drug release at acidic pH values. In vitro cellular uptake shows that the DOX-loaded nanogels could be preferentially internalized by two-dimensional (2D) cells and three-dimensional (3D) multicellular spheroids (MCs), resulting in higher inhibition of the proliferation of tumor cells. In vivo biodistribution and anti-tumor effect were determined in H22 tumor-bearing mice, and the results demonstrate that the acid-labile MASCS nanogels can significantly prolong the blood circulation time of DOX and improve the accumulation in tumor areas, leading to higher therapeutic efficacy. We designed new pH-triggered chitosan nanogels via an ortho ester-based cross-linker for efficient drug-loading and chemotherapy. These drug-loaded nanogels exhibit excellent pH-triggered drug release behavior due to the degradation of ortho ester linkages in mildly acidic environments. In vitro and in vivo results demonstrate that the nanogels could be efficiently internalized by 2D cells and 3D-MCs, improve drug concentration in solid tumors, and lead to higher therapeutic efficacy. To the best of our knowledge, this is the first report on using an ortho ester-based cross-linker to prepare pH-triggered chitosan nanogels as tumor carriers, which may provide a potential route for improved safety and to increase the therapeutic efficacy of anticancer therapy. Copyright © 2017

  11. Comparison of indirect and direct quantification of esters of monochloropropanediol in vegetable oil.

    Science.gov (United States)

    Dubois, Mathieu; Tarres, Adrienne; Goldmann, Till; Empl, Anna Maria; Donaubauer, Alfred; Seefelder, Walburga

    2012-05-04

    The presence of fatty acid esters of monochloropropanediol (MEs) in food is a recent concern raised due to the carcinogenicity of their hydrolysable moieties 2- and 3-monochloropropanediol (2- and 3-MCPD). Several indirect methods for the quantification of MEs have been developed and are commonly in use until today, however significant discrepancies among analytical results obtained are challenging their reliability. The aim of the present study was therefore to test the trueness of an indirect method by comparing it to a newly developed direct method using palm oil and palm olein as examples. The indirect method was based on ester cleavage under acidic conditions, derivatization of the liberated 2- and 3-MCPD with heptafluorobutyryl imidazole and GC-MS determination. The direct method was comprised of two extraction procedures targeting 2-and 3-MCPD mono esters (co-extracting as well glycidyl esters) by the use of double solid phase extraction (SPE), and 2- and 3-MCPD di-esters by the use of silica gel column, respectively. Detection was carried out by liquid chromatography coupled to time of flight mass spectrometry (LC-ToF-MS). Accurate quantification of the intact compounds was assured by means of matrix matched standard addition on extracts. Analysis of 22 palm oil and 7 palm olein samples (2- plus 3-MCPD contamination ranged from 0.3 to 8.8 μg/g) by both methods revealed no significant bias. Both methods were therefore considered as comparable in terms of results; however the indirect method was shown to require less analytical standards, being less tedious and furthermore applicable to all type of different vegetable oils and hence recommended for routine application. Copyright © 2012 Elsevier B.V. All rights reserved.

  12. Large-scale enzymatic production of natural flavour esters in organic solvent with continuous water removal.

    Science.gov (United States)

    Gubicza, L; Kabiri-Badr, A; Keoves, E; Belafi-Bako, K

    2001-11-30

    A new, large-scale process was developed for the enzymatic production of low molecular weight flavour esters in organic solvent. Solutions for the elimination of substrate and product inhibitions are presented. The excess water produced during the process was continuously removed by hetero-azeotropic distillation and esters were produced at yields of over 90%.

  13. Poly(ether ester amide)s for tissue engineering

    NARCIS (Netherlands)

    Deschamps, A.A.; van Apeldoorn, Aart A.; de Bruijn, Joost Dick; Grijpma, Dirk W.; Feijen, Jan

    2003-01-01

    Poly(ether ester amide) (PEEA) copolymers based on poly(ethylene glycol) (PEG), 1,4-butanediol and dimethyl-7,12-diaza-6,13-dione-1,18-octadecanedioate were evaluated as scaffold materials for tissue engineering. A PEEA copolymer based on PEG with a molecular weight of 300 g/mol and 25 wt% of soft

  14. 21 CFR 175.210 - Acrylate ester copolymer coating.

    Science.gov (United States)

    2010-04-01

    ... ester copolymer coating may safely be used as a food-contact surface of articles intended for packaging..., and methacrylic acid applied in emulsion form to molded virgin fiber and heat-cured to an insoluble... application of the emulsion may include substances named in this paragraph, in an amount not to exceed that...

  15. α,β-Unsaturated monoterpene acid glucose esters: structural diversity, bioactivities and functional roles.

    Science.gov (United States)

    Goodger, Jason Q D; Woodrow, Ian E

    2011-12-01

    The glycosylation of lipophilic small molecules produces many important plant secondary metabolites. The majority of these are O-glycosides with relatively fewer occurring as glucose esters of aromatic or aliphatic acids. In particular, monoterpene acid glucose esters have much lower structural diversity and distribution compared to monoterpene glycosides. Nevertheless, there have been over 20 monoterpene acid glucose esters described from trees in the genus Eucalyptus (Myrtaceae) in recent years, all based on oleuropeic acid, menthiafolic acid or both. Here we review all of the glucose esters containing these monoterpenoids identified in plants to date. Many of the compounds contain phenolic aglycones and all contain at least one α,β-unsaturated carbonyl, affording a number of important potential therapeutic reactivities such as anti-tumor promotion, carcinogenesis suppression, and anti-oxidant and anti-inflammatory activities. Additional properties such as cytotoxicity, bitterness, and repellency are suggestive of a role in plant defence, but we also discuss their localization to the exterior of foliar secretory cavity lumina, and suggest they may also protect secretory cells from toxic terpenes housed within these structures. Finally we discuss how the use of a recently developed protocol to isolate secretory cavities in a functional state could be used in conjunction with systems biology approaches to help characterize their biosynthesis and roles in plants. Copyright © 2011 Elsevier Ltd. All rights reserved.

  16. Assessment of Phthalate Esters in A Variety of Carbonated Beverages Bottled in PET

    Directory of Open Access Journals (Sweden)

    Mojtaba Moazzen

    2014-12-01

    Full Text Available Background: Phthalate esters are polymeric compounds usually used as a plasticizer. These materials can enter to the human body through various ways the main way could be food packaging. Chronic contact with these materials could result cancer, including breast cancer in women and prostate cancer in men as well as other endocrine problems. The objective of this study was to assess the concentration of phthalate esters in carbonated beverages. Methods: In this study, a magnetic nano-scale adsorbent, made from carbon nanotubes and Fe3O4. Deposition of Fe3O4 on the adsorbent could result in improvement of adsorption and desorption as well as extraction procedure. Then, by means of adsorbent and solvent extraction, phthalate esters were extracted from the beverage matrices and determined using GC-MS analysis. Results: amongst studied ingredients, BEP or DEHP, that have been found to be carcinogenic, had highest concentration in beverages, and also the brand of A and taste of C had the highest average concentration. Except one sample, the total amounts of these ingredients were below than international standards. Conclusion: Based on the results, consumers can use these beverages without any concern regarding phthalate esters amounts. The results also demonstrated that this synthesized adsorbent has good performance for extraction of phthalates from studied matrices.

  17. Decarbonylative Silylation of Esters by Combined Nickel and Copper Catalysis for the Synthesis of Arylsilanes and Heteroarylsilanes

    KAUST Repository

    Guo, Lin; Chatupheeraphat, Adisak; Rueping, Magnus

    2016-01-01

    An efficient nickel/copper-catalyzed decarbonylative silylation reaction of carboxylic acid esters with silylboranes is described. This reaction provides access to structurally diverse silanes with high efficiency and excellent functional-group tolerance starting from readily available esters.

  18. Decarbonylative Silylation of Esters by Combined Nickel and Copper Catalysis for the Synthesis of Arylsilanes and Heteroarylsilanes

    KAUST Repository

    Guo, Lin

    2016-08-25

    An efficient nickel/copper-catalyzed decarbonylative silylation reaction of carboxylic acid esters with silylboranes is described. This reaction provides access to structurally diverse silanes with high efficiency and excellent functional-group tolerance starting from readily available esters.

  19. Role of sulfate ester in influencing biological activity of cholecystokinin-related peptides

    International Nuclear Information System (INIS)

    Vinayek, R.; Jensen, R.T.; Gardner, J.D.

    1987-01-01

    In dispersed acini from guinea pig, mouse, or rat pancreas cholecystokinin-(27-33) is a full agonist, and removing the sulfate ester from the tyrosine residue in position 27 caused a 100- to 300-fold decrease in potency with no change in efficacy. In dispersed acini from mouse or rat pancreas, cholecystokinin-(27-32)-NH 2 is a partial agonist, and removing the sulfate ester from the tyrosine in position 27 abolished the efficacy. The desulfated peptide was able, however, to interact with [ 125 I] CCK receptors with a potency that was threefold less than that of cholecystokinin-(27-32)-NH 2 and therefore functioned as a cholecystokinin receptor antagonist. In dispersed acini from guinea pig pancreas cholecystokinin-(27-32)-NH 2 is a cholecystokinin receptor antagonist. Removing the sulfate ester from the tyrosine residue in position 27 of cholecystokinin-(27-32)-NH 2 caused a fourfold decrease in potency but did not abolish the ability of the peptide to interact with cholecystokinin receptors; therefore, desulfated cholecystokinin-(27-32)-NH 2 functioned as a cholecystokinin receptor antagonist

  20. Gas chromatography-vacuum ultraviolet spectroscopy for analysis of fatty acid methyl esters.

    Science.gov (United States)

    Fan, Hui; Smuts, Jonathan; Bai, Ling; Walsh, Phillip; Armstrong, Daniel W; Schug, Kevin A

    2016-03-01

    A new vacuum ultraviolet (VUV) detector for gas chromatography was recently developed and applied to fatty acid methyl ester (FAME) analysis. VUV detection features full spectral acquisition in a wavelength range of 115-240nm, where virtually all chemical species absorb. VUV absorption spectra of 37 FAMEs, including saturated, monounsaturated, and polyunsaturated types were recorded. Unsaturated FAMEs show significantly different gas phase absorption profiles than saturated ones, and these classes can be easily distinguished with the VUV detector. Another advantage includes differentiating cis/trans-isomeric FAMEs (e.g. oleic acid methyl ester and linoleic acid methyl ester isomers) and the ability to use VUV data analysis software for deconvolution of co-eluting signals. As a universal detector, VUV also provides high specificity, sensitivity, and a fast data acquisition rate, making it a powerful tool for fatty acid screening when combined with gas chromatography. The fatty acid profile of several food oil samples (olive, canola, vegetable, corn, sunflower and peanut oils) were analyzed in this study to demonstrate applicability to real world samples. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Phenolic Esters of O-Desmethylvenlafaxine with Improved Oral Bioavailability and Brain Uptake

    Directory of Open Access Journals (Sweden)

    Yang Zhang

    2013-12-01

    Full Text Available O-Desmethylvenlafaxine (desvenlafaxine, ODV is a recently approved antidepressant which in some clinical studies failed to meet a satisfactory end-point. The aim of this study was to prepare a series of phenolic esters of ODV and evaluate their potential as ODV prodrugs with improved brain uptake. Fifteen phenolic esters (compounds 1a–o were synthesized and their pharmacokinetic profiles evaluated in rat. The four compounds producing the highest relative bioavailability of ODV in rat (compounds 1c, 1e, 1n, 1o were then studied to evaluate their brain uptake. Of these four compounds, compound 1n (the piperonylic acid ester of ODV demonstrated the highest Cmax of ODV both in the rat hypothalamus and total brain. Finally the pharmacokinetics of 1n were evaluated in beagle dog where the increase in relative bioavailability of ODV was found to be as great as in rat. This high relative bioavailability of ODV coupled with its good brain penetration make 1n the most promising candidate for development as an ODV prodrug.

  2. Esterase- and pH-responsive poly(β-amino ester)-capped mesoporous silica nanoparticles for drug delivery

    Science.gov (United States)

    Fernando, Isurika R.; Ferris, Daniel P.; Frasconi, Marco; Malin, Dmitry; Strekalova, Elena; Yilmaz, M. Deniz; Ambrogio, Michael W.; Algaradah, Mohammed M.; Hong, Michael P.; Chen, Xinqi; Nassar, Majed S.; Botros, Youssry Y.; Cryns, Vincent L.; Stoddart, J. Fraser

    2015-04-01

    Gating of mesoporous silica nanoparticles (MSNs) with the stimuli-responsive poly(β-amino ester) has been achieved. This hybrid nanocarrier releases doxorubicin (DOX) under acidic conditions or in the presence of porcine liver esterase. The DOX loaded poly(β-amino ester)-capped MSNs reduce cell viability when tested on MDA-MB-231 human breast cancer cells.Gating of mesoporous silica nanoparticles (MSNs) with the stimuli-responsive poly(β-amino ester) has been achieved. This hybrid nanocarrier releases doxorubicin (DOX) under acidic conditions or in the presence of porcine liver esterase. The DOX loaded poly(β-amino ester)-capped MSNs reduce cell viability when tested on MDA-MB-231 human breast cancer cells. Electronic supplementary information (ESI) available: Experimental details relating to (i) the synthesis and characterisation of the surface-functionalised MSN and POL (ii) cargo-loading and release studies in solution, (iii) cellular internalisation of nanomaterials, and (iv) cell viability tests. See DOI: 10.1039/c4nr07443b

  3. Degradation of phorbol esters by Pseudomonas aeruginosa PseA during solid-state fermentation of deoiled Jatropha curcas seed cake.

    Science.gov (United States)

    Joshi, Chetna; Mathur, Priyanka; Khare, S K

    2011-04-01

    Large amount of seed cake is generated as by-product during biodiesel production from Jatropha seeds. Presence of toxic phorbol esters restricts its utilization as livestock feed. Safe disposal or meaningful utilization of this major by-product necessitates the degradation of these phorbol esters. The present study describes the complete degradation of phorbol esters by Pseudomonas aeruginosa PseA strain during solid state fermentation (SSF) of deoiled Jatropha curcas seed cake. Phorbol esters were completely degraded in nine days under the optimized SSF conditions viz. deoiled cake 5.0 g; moistened with 5.0 ml distilled water; inoculum 1.5 ml of overnight grown P. aeruginosa; incubation at temperature 30 °C, pH 7.0 and RH 65%. SSF of deoiled cake seems a potentially viable approach towards the complete degradation of the toxic phorbol esters. Copyright © 2011 Elsevier Ltd. All rights reserved.

  4. Novel cellulose ester substrates for high performance flat-sheet thin-film composite (TFC) forward osmosis (FO) membranes

    KAUST Repository

    Ong, Rui Chin; Chung, Neal Tai-Shung; de Wit, Jos S.; Helmer, Bradley J.

    2015-01-01

    and seawater desalination with high performance. The performance of TFC-FO membranes prepared from the hydrophilic cellulose ester containing a high degree of OH and a moderate degree of Pr substitutions clearly surpasses those prepared from cellulose esters

  5. Modulation of the transient receptor potential vanilloid channel TRPV4 by 4alpha-phorbol esters: a structure-activity study

    DEFF Research Database (Denmark)

    Klausen, Thomas Kjaer; Pagani, Alberto; Minassi, Alberto

    2009-01-01

    The mechanism of activation of the transient receptor potential vanilloid 4 (TRPV4) channel by 4alpha-phorbol esters was investigated by combining information from chemical modification of 4alpha-phorbol-didecanoate (4alpha-PDD, 2a), site-directed mutagenesis, Ca(2+) imaging, and electrophysiology....... Binding of 4alpha-phorbol esters occurs in a loop in the TM3-TM4 domain of TRPV4 that is analogous to the capsaicin binding site of TRPV1, and the ester decoration of ring C and the A,B ring junction are critical for activity. The lipophilic ester groups on ring C serve mainly as a steering element...

  6. Synthesis of Fluoroalkoxy Substituted Arylboronic Esters by Iridium-Catalyzed Aromatic C–H Borylation

    KAUST Repository

    Batool, Farhat

    2015-08-17

    The preparation of fluoroalkoxy arylboronic esters by iridium-catalyzed aromatic C–H borylation is described. The fluoroalkoxy groups employed include trifluoromethoxy, difluoromethoxy, 1,1,2,2-tetrafluoroethoxy, and 2,2-difluoro-1,3-benzodioxole. The borylation reactions were carried out neat without the use of a glovebox or Schlenk line. The regioselectivities available through the iridium-catalyzed C–H borylation are complementary to those obtained by the electrophilic aromatic substitution reactions of fluoroalkoxy arenes. Fluoroalkoxy arylboronic esters can serve as versatile building blocks.

  7. Synthesis of Fluoroalkoxy Substituted Arylboronic Esters by Iridium-Catalyzed Aromatic C–H Borylation

    KAUST Repository

    Batool, Farhat; Parveen, Shehla; Emwas, Abdul-Hamid M.; Sioud, Salim; Gao, Xin; Munawar, Munawar A.; Chotana, Ghayoor A.

    2015-01-01

    The preparation of fluoroalkoxy arylboronic esters by iridium-catalyzed aromatic C–H borylation is described. The fluoroalkoxy groups employed include trifluoromethoxy, difluoromethoxy, 1,1,2,2-tetrafluoroethoxy, and 2,2-difluoro-1,3-benzodioxole. The borylation reactions were carried out neat without the use of a glovebox or Schlenk line. The regioselectivities available through the iridium-catalyzed C–H borylation are complementary to those obtained by the electrophilic aromatic substitution reactions of fluoroalkoxy arenes. Fluoroalkoxy arylboronic esters can serve as versatile building blocks.

  8. Melon oil methyl ester: an environmentally friendly fuel

    Directory of Open Access Journals (Sweden)

    S.K. Fasogbon

    2015-06-01

    Full Text Available Demand for energy is growing across the globe due to the direct relationship between the well-being and prosperity of people and energy usage. However, meeting this growing energy demand in a safe and environmentally friendly manner is a key challenge. To this end, methyl esters (biodiesels have been and are being widely investigated as alternatives to fossil fuels in compression ignition engines. In this study, melon (Colocynthis Citrullus Lanatus oil was used to synthesize biodiesel (methyl ester using the transesterification method in the presence of a sodium hydroxide promoter. The emissions profile of the biodiesel was investigated by setting up a single-cylinder four-stroke air-cooled CI engine connected to a TD115-hydraulic dynamometer and an Eclipse Flue Gas Analyzer (FGA with model number EGA4 flue gas analyzer. The engine was run at engine speeds of 675, 1200 and 1900rpm for biodiesel/diesel blends at 21°C on a volume basis of 0/100(B0, 10/90(B10, 20/80(B20, 30/70(B30, 40/60(B40 and 50/50(B50. The test showed a downward trend in the emissions profile of the biodiesel, with remarkable reductions of about 55% in the dangerous-carbon monoxide exhaust gas pollutant and 33.3% in the unfriendly SOX from 100% diesel to B30-biodiesel concentration. Increasing the speed from 675 to 1200 and then to 1900 rpm also afforded further reductions in CO and SOX exhaust emissions. NOX however increased marginally by 2.1% from the same 100% diesel to the B30-biodiesel composition. Based on the remarkable reduction in CO and SOX and the marginal increase in NOX as the concentration of the biodiesel increased in the blends, the study concludes that melon oil methyl ester is an environmentally friendly fuel.

  9. Ethyl ester purpurine-18 from Gossypium mustelinum (Malvaceae)

    International Nuclear Information System (INIS)

    Silva, Tania Maria Sarmento; Camara, Celso Amorim; Barbosa-Filho, Jose Maria; Giulietti, Ana Maria

    2010-01-01

    The phaeophorbide ethyl ester named Purpurine-18 and the flavonoids quercetin and kaempferol were obtained by chromatographic procedures from the chloroform fraction of aerial parts of Gossypium mustelinum. The structure of these compound was determined by NMR, IR and mass spectra data analysis. This is the first occurrence of this compound in Angiosperm. (author)

  10. Effect of sample pre-treatment on the determination of steroid esters in hair of bovine calves

    NARCIS (Netherlands)

    Aqai, P.; Stolker, A.A.M.; Lasaroms, J.J.P.

    2009-01-01

    The effect of three sample pre-treatment steps, washing, cutting and grinding on the determination of steroid esters in hair is studied. The study is performed by using hair samples obtained after pour-on application of steroid esters to bovine calves. After sample pre-treatment the hair is treated

  11. A 13-week repeated dose study of three 3-monochloropropane-1,2-diol fatty acid esters in F344 rats.

    Science.gov (United States)

    Onami, Saeko; Cho, Young-Man; Toyoda, Takeshi; Mizuta, Yasuko; Yoshida, Midori; Nishikawa, Akiyoshi; Ogawa, Kumiko

    2014-04-01

    3-monochloropropane-1,2-diol (3-MCPD), a rat renal and testicular carcinogen, has been reported to occur in various foods and food ingredients as free or esterified forms. Since reports about toxicity of 3-MCPD esters are limited, we conducted a 13-week rat subchronic toxicity study of 3-MCPD esters (palmitate diester: CDP, palmitate monoester: CMP, oleate diester: CDO). We administered a carcinogenic dose (3.6 × 10(-4) mol/kg B.W./day) of 3-MCPD or these esters at equimolar concentrations and two 1/4 lower doses by gavage with olive oil as a vehicle five times a week for 13 weeks to F344 male and female rats. As a result, five out of ten 3-MCPD-treated females died from acute renal tubular necrosis, but none of the ester-treated rats. Decreased HGB was observed in all high-dose 3-MCPD fatty acid ester-treated rats, except CDO-treated males. The absolute and relative kidney weights were significantly increased in the ester-treated rats at medium and high doses. Relative liver weights were significantly increased in the esters-treated rat at high dose, except for CMP females. Significant increase in apoptotic epithelial cells in the initial segment of the epididymis of high-dose ester-treated males was also observed. The results suggested that although acute renal toxicity was lower than 3-MCPD, these three 3-MCPD fatty acid esters have the potential to exert subchronic toxicity to the rat kidneys and epididymis, to a similar degree as 3-MCPD under the present conditions. NOAELs (no-observed-adverse-effect levels) of CDP, CMP and CDO were suggested to be 14, 8 and 15 mg/kg B.W./day, respectively.

  12. Engineering low phorbol ester Jatropha curcas seed by intercepting casbene biosynthesis.

    Science.gov (United States)

    Li, Chunhong; Ng, Ailing; Xie, Lifen; Mao, Huizhu; Qiu, Chengxiang; Srinivasan, Ramachandran; Yin, Zhongchao; Hong, Yan

    2016-01-01

    Casbene is a precursor to phorbol esters and down-regulating casbene synthase effectively reduces phorbol ester biosynthesis. Seed-specific reduction of phorbol ester (PE) helps develop Jatropha seed cake for animal nutrition. Phorbol esters (PEs) are diterpenoids present in some Euphorbiaceae family members like Jatropha curcas L. (Jatropha), a tropical shrub yielding high-quality oil suitable as feedstock for biodiesel and bio jet fuel. Jatropha seed contains up to 40 % of oil and can produce oil together with cake containing high-quality proteins. However, skin-irritating and cancer-promoting PEs make Jatropha cake meal unsuitable for animal nutrition and also raise some safety and environmental concerns on its planting and processing. Two casbene synthase gene (JcCASA163 and JcCASD168) homologues were cloned from Jatropha genome and both genes were highly expressed during seed development. In vitro functional analysis proved casbene synthase activity of JcCASA163 in converting geranylgeranyl diphosphate into casbene which has been speculated to be the precursor to PEs. A seed-specific promoter driving inverted repeats for RNAi interference targeting at either JcCASA163 or both genes could effectively down-regulate casbene synthase gene expression with concurrent marked reduction of PE level (by as much as 85 %) in seeds with no pleiotropic effects observed. Such engineered low PE in seed was heritable and co-segregated with the transgene. Our work implicated casbene synthase in Jatropha PE biosynthesis and provided evidence for casbene being the precursor for PEs. The success in reducing seed PE content through down-regulation of casbene synthase demonstrates the feasibility of intercepting PE biosynthesis in Jatropha seed to help address safety concerns on Jatropha plantation and seed processing and facilitate use of its seed protein for animal nutrition.

  13. In vitro pharmacokinetics of anti-psoriatic fumaric acid esters

    NARCIS (Netherlands)

    N.H.R. Litjens (Nicolle); E. van Strijen (Elizabeth); C. van Gulpen (Co); H. Mattie (Herman); J.T. van Dissel (Jaap); H.B. Thio (Bing); P.H. Nibbering (Peter)

    2004-01-01

    textabstractBackground: Psoriasis is a chronic inflammatory skin disease that can be successfully treated with a mixture of fumaric acid esters (FAE) formulated as enteric-coated tablets for oral use. These tablets consist of dimethylfumarate (DMF) and salts of monoethylfumarate (MEF) and its main

  14. Cytosolic cholesterol ester hydrolase in adrenal cortex

    OpenAIRE

    Tocher, Douglas R.

    1983-01-01

    Cholesterol ester hydrolase (CEH) in adrenocortical cytosol was known to be phosphorylated and activated, in response to ACTH in a cAMPdependent protein kinase mediated process. The purification of CEH from bovine adrenocortical cytosol was attempted. The use of detergents to solubilise the enzyme from lipid-rich aggregates was investigated and sodium cholate was found to be effective. A purification procedure using cholate solubilised enzyme was developed. The detergent int...

  15. Fatty acid esters produced by Lasiodiplodia theobromae function as growth regulators in tobacco seedlings

    International Nuclear Information System (INIS)

    Uranga, Carla C.; Beld, Joris; Mrse, Anthony; Córdova-Guerrero, Iván; Burkart, Michael D.; Hernández-Martínez, Rufina

    2016-01-01

    The Botryosphaeriaceae are a family of trunk disease fungi that cause dieback and death of various plant hosts. This work sought to characterize fatty acid derivatives in a highly virulent member of this family, Lasiodiplodia theobromae. Nuclear magnetic resonance and gas chromatography-mass spectrometry of an isolated compound revealed (Z, Z)-9,12-ethyl octadecadienoate, (trivial name ethyl linoleate), as one of the most abundant fatty acid esters produced by L. theobromae. A variety of naturally produced esters of fatty acids were identified in Botryosphaeriaceae. In comparison, the production of fatty acid esters in the soil-borne tomato pathogen Fusarium oxysporum, and the non-phytopathogenic fungus Trichoderma asperellum was found to be limited. Ethyl linoleate, ethyl hexadecanoate (trivial name ethyl palmitate), and ethyl octadecanoate, (trivial name ethyl stearate), significantly inhibited tobacco seed germination and altered seedling leaf growth patterns and morphology at the highest concentration (0.2 mg/mL) tested, while ethyl linoleate and ethyl stearate significantly enhanced growth at low concentrations, with both still inducing growth at 98 ng/mL. This work provides new insights into the role of naturally esterified fatty acids from L. theobromae as plant growth regulators with similar activity to the well-known plant growth regulator gibberellic acid. - Highlights: • Lasiodiplodia theobromae produces a wide variety of fatty acid esters in natural substrates. • Ethyl stearate and ethyl linoleate inhibit tobacco germination at 0.2 mg/mL. • Ethyl stearate and ethyl linoleate induce tobacco germination at 98 ng/mL. • Tobacco growth increase in ethyl stearate and ethyl linoleate parallels gibberellic acid. • A role as plant growth regulators is proposed for fatty acid esters.

  16. Fatty acid esters produced by Lasiodiplodia theobromae function as growth regulators in tobacco seedlings

    Energy Technology Data Exchange (ETDEWEB)

    Uranga, Carla C., E-mail: curanga@cicese.edu.mx [Centro de Investigación Científica y de Educación Superior de Ensenada (CICESE), Carretera Ensenada-Tijuana 3918, Zona Playitas, 22860 Ensenada, B.C. (Mexico); Beld, Joris, E-mail: joris.beld@drexelmed.edu [University of California, San Diego, Department of Chemistry and Biochemistry, 9500 Gilman Dr., La Jolla, CA 92093-0358 (United States); Mrse, Anthony, E-mail: amrse@ucsd.edu [University of California, San Diego, Department of Chemistry and Biochemistry, 9500 Gilman Dr., La Jolla, CA 92093-0358 (United States); Córdova-Guerrero, Iván, E-mail: icordova@uabc.edu.mx [Universidad Autónoma de Baja California (UABC), Calzada Universidad 14418 Parque Industrial Internacional Tijuana, Tijuana, B.C. 22390 (Mexico); Burkart, Michael D., E-mail: mburkart@ucsd.edu [University of California, San Diego, Department of Chemistry and Biochemistry, 9500 Gilman Dr., La Jolla, CA 92093-0358 (United States); Hernández-Martínez, Rufina, E-mail: ruhernan@cicese.mx [Centro de Investigación Científica y de Educación Superior de Ensenada (CICESE), Carretera Ensenada-Tijuana 3918, Zona Playitas, 22860 Ensenada, B.C. (Mexico)

    2016-04-01

    The Botryosphaeriaceae are a family of trunk disease fungi that cause dieback and death of various plant hosts. This work sought to characterize fatty acid derivatives in a highly virulent member of this family, Lasiodiplodia theobromae. Nuclear magnetic resonance and gas chromatography-mass spectrometry of an isolated compound revealed (Z, Z)-9,12-ethyl octadecadienoate, (trivial name ethyl linoleate), as one of the most abundant fatty acid esters produced by L. theobromae. A variety of naturally produced esters of fatty acids were identified in Botryosphaeriaceae. In comparison, the production of fatty acid esters in the soil-borne tomato pathogen Fusarium oxysporum, and the non-phytopathogenic fungus Trichoderma asperellum was found to be limited. Ethyl linoleate, ethyl hexadecanoate (trivial name ethyl palmitate), and ethyl octadecanoate, (trivial name ethyl stearate), significantly inhibited tobacco seed germination and altered seedling leaf growth patterns and morphology at the highest concentration (0.2 mg/mL) tested, while ethyl linoleate and ethyl stearate significantly enhanced growth at low concentrations, with both still inducing growth at 98 ng/mL. This work provides new insights into the role of naturally esterified fatty acids from L. theobromae as plant growth regulators with similar activity to the well-known plant growth regulator gibberellic acid. - Highlights: • Lasiodiplodia theobromae produces a wide variety of fatty acid esters in natural substrates. • Ethyl stearate and ethyl linoleate inhibit tobacco germination at 0.2 mg/mL. • Ethyl stearate and ethyl linoleate induce tobacco germination at 98 ng/mL. • Tobacco growth increase in ethyl stearate and ethyl linoleate parallels gibberellic acid. • A role as plant growth regulators is proposed for fatty acid esters.

  17. Feasibility of bio-based lactate esters as extractant for biobutanol recovery: (Liquid + liquid) equilibria

    International Nuclear Information System (INIS)

    Zheng, Shaohua; Cheng, Hongye; Chen, Lifang; Qi, Zhiwen

    2016-01-01

    Highlights: • Lactate esters were studied as solvent to remove butanol from aqueous media. • (Liquid + liquid) equilibrium data were measured at T = 298.15 K and 1 atm. • Selectivity and 1-butanol partition coefficient were calculated. • COSMO-based study of separation efficiency on solvent structure was conducted. - Abstract: As bio-based solvents, lactate esters can be used as extractant for removing 1-butanol from the aqueous fermentation broths. In order to evaluate the separation efficiency of butyl lactate and 2-ethylhexyl lactate for the extraction of 1-butanol from its mixture with water, the (liquid + liquid) equilibrium for the ternary systems {water (1) + 1-butanol (2) + lactate ester (3)} were measured at T = 298.15 K. The 1-butanol partition coefficient varied in the range of 4.46 to 10.29, and the solvent selectivity within 32.12 to 108.18. For the separation of low-concentration butanol from fermentation broths, butyl lactate exhibits higher partition coefficient and lower selectivity than 2-ethylhexyl lactate. The NRTL model was employed to correlate the experimental data, and the COSMO-RS theory was utilized to predict the (liquid + liquid) equilibria and to analyze the influence of lactate esters on extraction efficiency.

  18. Hydrolysis kinetics of astaxanthin esters and stability of astaxanthin of Haematococcus pluvialis during saponification.

    Science.gov (United States)

    Yuan, J P; Chen, F

    1999-01-01

    The reaction kinetics for the hydrolysis of astaxanthin esters and the degradation of astaxanthin during saponification of the pigment extract from the microalga Haematococcus pluvialis were investigated. Different concentrations of sodium hydroxide in methanol were used for the saponification under nitrogen in darkness at ambient temperature (22 degrees C) followed by the analysis of astaxanthins and other carotenoids using an HPLC method. The concentration of methanolic NaOH solution was important for promoting the hydrolysis of astaxanthin esters and minimizing the degradation of astaxanthin during saponification. With a higher concentration of methanolic NaOH solution, the reaction rate of hydrolysis was high, but the degradation of astaxanthin occurred significantly. The rate constants of the hydrolysis reaction (first order) of astaxanthin esters and the degradation reaction (zero-order) of astaxanthin were directly proportional to the concentration of sodium hydroxide in the saponified solution. Although the concentration of sodium hydroxide in the saponified solution was 0.018 M, complete hydrolysis of astaxanthin esters was achieved in 6 h for different concentrations (10-100 mg/L) of pigment extracts. Results also indicated that a higher temperature should be avoided to minimize the degradation of astaxanthin. In addition, during saponification, no loss of lutein, beta-carotene, and canthaxanthin was found.

  19. 40 CFR 721.3100 - Oligomeric silicic acid ester compound with a hy-droxyl-al-kyla-mine.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Oligomeric silicic acid ester compound with a hy-droxyl-al-kyla-mine. 721.3100 Section 721.3100 Protection of Environment ENVIRONMENTAL... Significant New Uses for Specific Chemical Substances § 721.3100 Oligomeric silicic acid ester compound with a...

  20. VALIDASI MODIFIKASI METODE WEIßHAAR UNTUK ANALISIS 3-MCPD ESTER DALAM MINYAK GORENG SAWIT [Validation of Modified Weißhaar’s Method for 3-MCPD Esters Analysis in Palm Oil

    OpenAIRE

    Tanti Lanovia1,2)*; Nuri Andarwulan1,3); Purwiyatno Hariyadi1,3)

    2014-01-01

    The 3-monochloropropane-1,2-diol (3-MCPD) and 3-MCPD esters were found in any type of refined vegetable oil -mostly produced during the refining process- and recognized as emerging food contaminants. Several analytical methods have been developed and one of which was a Weißhaar's method. The study aims to validate the modified Weißhaar's method for analysis of 3-MCPD and 3-MCPD esters in refined palm oil. Ion fragments were used for identification and quantification of 3-MCPD and 3-MCPD-d5. 3...

  1. Evaluation of the levels of phthalate ester plasticizers in surface ...

    African Journals Online (AJOL)

    Evaluation of the levels of phthalate ester plasticizers in surface water of Ethiope ... Gas chromatography (GC) coupled with mass spectrometer (MS) was used to ... with their common use in plastic materials and other industrial chemicals.

  2. LNG TERMINAL SAFE OPERATION MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Andrzej ADAMKIEWICZ

    2012-07-01

    Full Text Available This article presents the significance of LNG terminal safety issues in natural gas sea transport. It shows particular requirements for LNG transmission installations resulting from the specific properties of LNG. Out of the multi‐layer critical safety areas comprising structural elements of the terminal safety system, possibilities to decrease the risk of emergency occurrence on LNG terminals have been selected. Tasks performed by the LNG terminal, together with its own personnel and the outside one, have been defined. General theses for LNG terminal safety have been formulated.

  3. Matrix isolation FT-IR spectroscopy and molecular orbital study of sarcosine methyl ester

    OpenAIRE

    Gómez-Zavaglia, Andrea; Fausto, R.

    2004-01-01

    N-methylglycine methyl ester (sarcosine-Me) has been studied by matrix isolation FT-IR spectroscopy and molecular orbital calculations undertaken at the DFT/B3LYP and MP2 levels of theory with the 6-311++G(d,p) and 6-31++G(d,p) basis set, respectively. Twelve different conformers were located in the potential energy surface of the studied compound, with the ASC conformer being the ground conformational state. This form is analogous to the dimethylglycine methyl ester most stable conformer and...

  4. A Ketone Ester Drink Increases Postexercise Muscle Glycogen Synthesis in Humans.

    Science.gov (United States)

    Holdsworth, David A; Cox, Peter J; Kirk, Tom; Stradling, Huw; Impey, Samuel G; Clarke, Kieran

    2017-09-01

    Physical endurance can be limited by muscle glycogen stores, in that glycogen depletion markedly reduces external work. During carbohydrate restriction, the liver synthesizes the ketone bodies, D-β-hydroxybutyrate, and acetoacetate from fatty acids. In animals and in the presence of glucose, D-β-hydroxybutyrate promotes insulin secretion and increases glycogen synthesis. Here we determined whether a dietary ketone ester, combined with plentiful glucose, can increase postexercise glycogen synthesis in human skeletal muscle. After an interval-based glycogen depletion exercise protocol, 12 well-trained male athletes completed a randomized, three-arm, blinded crossover recovery study that consisted of consumption of either a taste-matched, zero-calorie control or a ketone monoester drink, followed by a 10-mM glucose clamp or saline infusion for 2 h. The three postexercise conditions were control drink then saline infusion, control drink then hyperglycemic clamp, or ketone ester drink then hyperglycemic clamp. Skeletal muscle glycogen content was determined in muscle biopsies of vastus lateralis taken before and after the 2-h clamps. The ketone ester drink increased blood D-β-hydroxybutyrate concentrations to a maximum of 5.3 versus 0.7 mM for the control drink (P glycogen was 50% higher (246 vs 164 mmol glycosyl units per kilogram dry weight, P glycogen synthesis.

  5. Effect of a novel insulinotropic agent, succinic acid monoethyl ester ...

    Indian Academy of Sciences (India)

    Madhu

    index (AAI) (ratio of HDL-C to total cholesterol) were studied. ... ester; FFA, free falty acids; HDL-C, high density lipoprotein-cholesterol; LDL-C, low density lipoprotein-cholesterol; ..... and impaired catabolism of triglyceride-rich particles. The.

  6. Oleoyl and linoleoyl esters of fumonisin B1 are differently produced by Fusarium verticillioides on maize and rice based media.

    Science.gov (United States)

    Falavigna, C; Lazzaro, I; Galaverna, G; Dall'Asta, C; Battilani, P

    2016-01-18

    Fatty acid esters of fumonisins, namely oleoyl- and linoleoyl esters of fumonisin B1 (EFB1OA and EFB1LA, respectively), are modified forms of fumonisins whose formation and occurrence have been reported so far in naturally infected maize and in artificially inoculated rice. There is a lack of knowledge about the mechanism of formation, mainly in relation to the role played by the substrate. Therefore, in this work we studied the dynamics of accumulation of the toxin and its esters, together with their precursor, in maize and rice based media inoculated with different strains of F. verticillioides and incubated at 25 °C for 7-45 days. The production pattern of FB1 and its modified forms was significantly influenced by growth media, reaching a higher concentration in cornmeal compared to rice based medium. Similarly, cornmeal was more supportive for the conversion of FB1 by considering the esterification rate, with a prevalence of linoleoyl esters compared to oleoyl esters resembling the OA/LA rate in both media. The conversion of FB1 into fatty acid esters was also shown as strain-related. Results, thus, strongly support the hypothesis that fatty acid esters of FB1 are produced by the fungus itself at a late stage of growth, or at a certain point of FB1 accumulation in the medium, using fatty acids from the substrate.

  7. Nonleaking battery terminals.

    Science.gov (United States)

    Snider, W. E.; Nagle, W. J.

    1972-01-01

    Three different terminals were designed for usage in a 40 ampere/hour silver zinc battery which has a 45% KOH by weight electrolyte in a plastic battery case. Life tests, including thermal cycling, electrical charge and discharge for up to three years duration, were conducted on these three different terminal designs. Tests for creep rate and tensile strength were conducted on the polyphenylene oxide plastic battery cases. Some cases were unused and others containing KOH electrolyte were placed on life tests. The design and testing of nonleaking battery terminals for use with a KOH electrolyte in a plastic case are considered.

  8. Experimental and Modeling Studies on the Synthesis and Properties of Higher Fatty Esters of Corn Starch

    NARCIS (Netherlands)

    Junistia, Laura; Sugih, Asaf K.; Manurung, Robert; Picchioni, Francesco; Janssen, Leon P. B. M.; Heeres, Hero J.

    This paper describes a systematic study on the synthesis of higher fatty esters of corn starch (starch laurate and starch stearate) by using the corresponding vinyl esters. The reactions were carried out in DMSO using basic catalysts (Na(2)HPO(4), K(2)CO(3), and Na-acetate). The effect of the

  9. Synthesis of amino ester-embedded benzimidazoles: a one-pot sequential protocol under metal-free neutral conditions.

    Science.gov (United States)

    Roy, Priyabrata; Bodhak, Chandan; Pramanik, Animesh

    2017-02-01

    A one-pot three-component protocol has been developed for the synthesis of amino ester-embedded benzimidazoles under metal-free neutral conditions. Sequentially, the methodology involves coupling of an amino ester with 1-fluoro-2-nitrobenzene, reduction of the coupled nitroarene by sodium dithionite, and cyclization of the corresponding diamine with an aldehyde.

  10. Are Polyphosphates or Phosphate Esters Prebiotic Reagents?

    Science.gov (United States)

    Keefe, Anthony D.; Miller, Stanley L.

    1995-01-01

    It is widely held that there was a phosphate compound in prebiotic chemistry that played the role of adenosine triphosphate and that the first living organisms had ribose-phosphate in the backbone of their genetic material. However, there are no known efficient prebiotic synthesis of high-energy phosphates or phosphate esters. We review the occurrence of phosphates in nature, the efficiency of the volcanic synthesis of P4O10, the efficiency of polyphosphate synthesis by heating phosphate minerals under geological conditions, and the use of high-energy organic compounds such as cyanamide or hydrogen cyanide. These are shown to be inefficient processes especially when the hydrolysis of the polyphosphates is taken into account. For example, if a whole atmosphere of methane or carbon monoxide were converted to cyanide which somehow synthesized polyphosphates quantitatively, the polyphosphate concentration in the ocean would still have been insignificant. We also attempted to find more efficient high-energy polymerizing agents by spark discharge syntheses, but without success. There may still be undiscovered robust prebiotic syntheses of polyphosphates, or mechanisms for concentrating them, but we conclude that phosphate esters may not have been constituents of the first genetic material. Phosphoanhydrides are also unlikely as prebiotic energy sources.

  11. Tribological study of a highly hydrolytically stable phenylboronic acid ester containing benzothiazolyl in mineral oil

    International Nuclear Information System (INIS)

    Li, Zhipeng; Li, Xiufeng; Zhang, Yawen; Ren, Tianhui; Zhao, Yidong; Zeng, Xiangqiong; Heide, E. van der

    2014-01-01

    A novel long chain alkyl phenylboronic acid ester containing heterocyclic compound, bis (1-(benzothiazol-2-ylthio) propan-2-yl)-4-dodecylphenylboronic acid ester (DBBMT), was synthesized and characterized. The hydrolytic stability of the DBBMT was evaluated and the results show that DBBMT is of outstanding hydrolytic stability compared with normal borate esters, which indicates that the designed molecular structure, by introducing benzene ring to conjugate with the electron-deficient boron and the benzothiazole as a hinder group, is effective on obtaining a hydrolytically stable long chain alkyl phenylboronic acid ester. The tribological properties of DBBMT and ZDDP in mineral base oil were evaluated using a four-ball tribometer, which suggests that the DBBMT possesses comprehensive tribological properties and could be a potential candidate for the replacement of ZDDP. Furthermore, in order to understand the tribological behaviors, the worn surface was analyzed by X-ray photoelectron spectroscopy (XPS) and X-ray absorption near edge structure (XANES) spectroscopy. The results indicate that the elements S, B, O and Fe perform complicated tribochemical reactions to form the compact tribological film composed of B 2 O 3 , FeS, Fe 3 O 4 and FeSO 4 .

  12. Experimental study on oral sulfhydryl as an adjuvant for improving nitrate ester tolerance in an animal model.

    Science.gov (United States)

    Chen, L; Jiang, J-Q; Zhang, Y; Feng, H

    2018-03-01

    As an initial step in exploring the feasibility of oral sulfhydryl as an adjuvant for improving nitrate ester tolerance, this study was designed to experimentally test the adjuvant therapy in a rabbit model of atherosclerosis (AS). New Zealand white rabbits with induced AS were randomly divided into four groups: AS group, AS + nitrate ester group, AS + nitrate ester tolerance group, and AS + drug combination group. Additionally, four equivalent groups with healthy New Zealand white rabbits without AS were also conformed. After feeding the animals for 5 days, the concentrations of superoxide anion (•O2-), superoxide dismutase (SOD), malondialdehyde (MDA), nitric oxide (NO), and endothelin-1 (ET-1) in blood and the relaxation response of the aortic ring were determined in each subject. The vascular plaques in different treatment groups were assessed by Hematoxylin and eosin (HE) staining to investigate the therapeutic value of sulfhydryl as coadjuvant for improving nitrate ester tolerance, and changes in blood vessels in different treatment groups were studied by immunohistochemical assays. Our results showed no significant differences through time in the concentrations of •O2-, SOD, MDA, NO, ET-1 between the healthy control and the nitrate ester groups (p > 0.05). The levels of SOD and MDA in the nitrate ester tolerance group increased with time, however, the levels of •O2-, NO and ET-1 decreased gradually (p tolerance groups were significantly decreased, but SOD and MDA were significantly increased (p tolerance, and this strategy was safe and looks promising for humans.

  13. In vivo transfer of cholesteryl ester from high and low density plasma lipoproteins into human aortic tissue

    International Nuclear Information System (INIS)

    Stender, S.; Hjelms, E.

    1988-01-01

    For the study of cholesteryl ester transfer from different plasma lipoproteins into human aortic tissue, patients scheduled for reconstructive aortic surgery were intravenously injected with autologous in vitro labeled lipoproteins 20 to 24 hours before aortic intima-media samples were obtained during the operation. The injectate contained high density lipoproteins (d greater than 1.063) labeled with 3H-cholesteryl ester and lipoproteins of lower density (d less than 1.063) labeled with 14C-cholesteryl ester or lipoproteins with the opposite labeling. In 16 aortic tissue samples (some with visible atherosclerosis) from 11 normocholesterolemic patients, the aortic influx of total cholesteryl ester was 1 to 50 nmol x cm-2 x day-1. Some 39% +/- 3% (mean +/- SEM) of the influx was derived from high density lipoproteins, which in plasma accounted for only 22% +/- 2% (mean +/- SEM) of the esterified cholesterol. The findings suggest that: 1) esterified cholesterol from the two lipoprotein fractions in plasma enter the aortic intima by the same mechanism, and 2) influx of cholesteryl ester from the smaller, high density lipoproteins is greater than influx from the larger, lower density lipoproteins considering their concentrations in plasma. In some patients, the cholesterol content in the intima-media tissue with no visible atherosclerosis corresponded to only a few months of continuous cholesteryl ester influx. This time is short considering the age of the patients and, therefore, indicates that removal of esterified cholesterol from the intima-media is of major importance in preventing cholesterol deposition in the arterial wall

  14. Synthesis and Suzuki Cross-Coupling Reactions of 2,6-Bis(trifluoromethyl)pyridine-4-boronic Acid Pinacol Ester

    KAUST Repository

    Batool, Farhat

    2016-11-18

    Iridium-catalyzed aromatic borylation provides quick one-step access to 2,6-bis(trifluoromethyl)pyridine-4-boronic acid pinacol ester. Suzuki couplings of this highly electron-deficient pyridine-4-boronic ester with various (hetero)aryl bromides was successfully carried out and the coupled products were obtained in 46–95% isolated yields. Double and triple Suzuki couplings, with dibromo- and tribromoarenes, respectively, were also achieved. Thus demonstrating that this pyridine-4-boronic ester can be a useful source for the installation of one of the strongest electron-withdrawing aromatic group in organic compounds. Copyright © 2016, Georg Thieme Verlag. All rights reserved.

  15. Synthesis and Suzuki Cross-Coupling Reactions of 2,6-Bis(trifluoromethyl)pyridine-4-boronic Acid Pinacol Ester

    KAUST Repository

    Batool, Farhat; Emwas, Abdul-Hamid M.; Gao, Xin; Munawar, Munawar A.; Chotana, Ghayoor A.

    2016-01-01

    Iridium-catalyzed aromatic borylation provides quick one-step access to 2,6-bis(trifluoromethyl)pyridine-4-boronic acid pinacol ester. Suzuki couplings of this highly electron-deficient pyridine-4-boronic ester with various (hetero)aryl bromides was successfully carried out and the coupled products were obtained in 46–95% isolated yields. Double and triple Suzuki couplings, with dibromo- and tribromoarenes, respectively, were also achieved. Thus demonstrating that this pyridine-4-boronic ester can be a useful source for the installation of one of the strongest electron-withdrawing aromatic group in organic compounds. Copyright © 2016, Georg Thieme Verlag. All rights reserved.

  16. Direct determination of 3-chloropropanol esters in edible vegetable oils using high resolution mass spectrometry (HRMS-Orbitrap).

    Science.gov (United States)

    Graziani, Giulia; Gaspari, Anna; Chianese, Donato; Conte, Lanfranco; Ritieni, Alberto

    2017-11-01

    A series of refined edible oils derived from mixed seeds, peanuts, corn, sunflower and palm obtained from the local supermarket were analyzed for their content of 3-MCPD esters. A direct analytical method for the determination of 3-monochloropropane-1,2-diol esters (3-MCPD esters) was applied to investigate the major MCPD esters found in common edible oils; in particular seven types of monoesters and eleven types of diesters were detected. The limits of detection (LODs) for monoesters and diesters of 3-MCPD were in the range of 0.079-12.678 µg kg -1 and 0.033-18.610 µg kg -1 in edible oils, and the ranges of limits of quantitation (LOQs) were 0.979-38.035 µg kg -1 and 0.100-55 µg kg -1 , respectively. The recoveries of 3-MCPD esters from oil samples were in the range of 80-100%, with RSD ranging between 1.9 and 11.8%. The concentration levels of total 3-MCPD diesters in vegetable oil samples were in the range from 0.106 up to 3.444 μg g -1 whereas total monoesters ranged from 0.005 up to 1.606 μg g -1 .

  17. Formulation de fluxants pour bitumes à base d’esters méthyliques d’huiles végétales

    Directory of Open Access Journals (Sweden)

    Alfos Carine

    2003-09-01

    Full Text Available Les fluxants pétroliers servent à améliorer la viscosité du bitume lors de son répandage, et par voie de conséquence le mouillage des granulats. Leur évaporation entraîne la montée en cohésion du revêtement. Malheureusement, ces produits d’origine fossile, outre les problèmes qu’ils posent en termes de COV, ne sont pas sans effet sur les conditions de travail des personnels de chantier et l’environnement (air, eau. De plus leur utilisation s’effectue à 160 °C -- au-dessus du point éclair -- et n’est pas sans présenter un risque d’explosion (les sites industriels de fabrication et de stockage de ces produits nécessitent une autorisation de type installations classées. Le recours à des esters méthyliques d’huiles végétales (EMVH, comme fluidifiant permet de remédier à ces inconvénients, mais, sans optimisation (ajout d’additifs, la montée en consistance du liant s’effectue plus lentement selon la réaction de siccativation liée à la présence de doubles liaisons sur les chaînes grasses des esters. L’influence des caractéristiques chimiques des esters (composition en acides gras, teneur en tocophérols notamment et de l’ajout, en quantité catalytique, d’huiles végétales siccatives sur la siccativité finale des liants EMVH, ont été étudiés. Différents esters méthyliques ont été testés (esters méthyliques de colza, de tournesol et de lin. Les analyses réalisées avant et après traitement thermique (1 h à 160 °C pour tenir compte des conditions réelles d’utilisation font apparaître des corrélations entre, teneur en tocophérols, richesse en doubles liaisons conjuguées et performances au séchage. Une modification de la formule sur base esters a été optimisée par incorporation d’huiles végétales siccatives. Il s’avère que ces huiles jouent le rôle d’activateur ou d’inhibiteur de séchage, selon la nature de l’ester méthylique employé. Des

  18. Palladium-mediated conversion of para-aminoarylboronic esters into para-aminoaryl- 11C-methanes

    DEFF Research Database (Denmark)

    Andersen, Valdemar Lykke; Herth, Matthias Manfred; Lehel, Szabolcs

    2013-01-01

    of free amines. Aryl boronic esters containing primary, secondary, and tertiary amines were successfully converted into corresponding labeled methyl derivatives in suf¿cient radiochemical yield to apply this method for tracer development. This procedure was applied to the labeling of CIMBI-712......Cross-couplings are an alternative to conventional 11C-methylations which are generally employed in PET tracer synthesis. Therefore, we set out to develop a general procedure for the synthesis of para-11CH3 labeled aromatic amines from the corresponding para-aminoarylboronic esters in the presence...

  19. Asymmetric Meerwein–Ponndorf–Verley reduction of long chain keto alkanoic acid methyl esters

    Directory of Open Access Journals (Sweden)

    AYE YUSUFOGLU

    2007-05-01

    Full Text Available 3-, 7- and 13-Monoketo tetradecanoic acid methyl esters carrying a ketogroup at the ends and at the middle of the chain with 14 carbon atoms were reduced by a Meerwein–Ponndorf–Verley reaction in the presence of R-(+-1,1'-binaphthalene-2,2'-diol, 1,2:5,6-D-di-O-isopropylidene-D-mannitol and L-(–-menthol. The highest enantiomeric purity of 65% ee was found for 13-hydroxy ester isomer. The enantiomeric excess was determined by 1H-NMR shift with Eu(tfc3 and by optical rotation.

  20. Immobilized lipase from Lactobacillus plantarum in meat degradation and synthesis of flavor esters

    Directory of Open Access Journals (Sweden)

    Sita Ramyasree Uppada

    2017-12-01

    Full Text Available Microbial lipases owing to their broad substrate specificity are widely used in various industrial applications like food processing, organic synthesis, detergent formulation and oil manufacturing. In the current study the immobilized lipase from Lactobacillus plantarum was found novel in degrading meat which can be applied in medical field and also in synthesizing different short chain fatty acid esters like 2,3,4-hydroxybenzyl acetates and triazole ester which makes a great impingement in natural flavor industry. The 4-hydroxybenzyl acetate obtained can also be used in cosmetics.

  1. Surface activity evaluation of an arabinose ester as water/oil demulsifier at severe conditions of temperature, salinity and pH; Avaliacao da atividade superficial de um ester de arabinose, como desemulsificante agua/oleo, em condicoes severas de temperatura, salinidade e pH

    Energy Technology Data Exchange (ETDEWEB)

    Borges, Mauricio Rodrigues; Garcia, Rosangela Balaban; Santos, Jaciara Alves dos; Vieira, Mariane; Silva, Luciana Carvalho; Campos, Viviane de Oliveira; Silva, Rayane Araujo da; Santos, Telma Pitanga dos [Universidade Federal do Rio Grande do Norte (UFRN), Natal, RN (Brazil)

    2008-07-01

    This work had for objective to compare the superficial properties of an arabinose ester, no-ionic, nontoxic, biodegradable, with two commercial products: the first one based on sodium dodecyl sulfate and the second one based on poly-oxy alkylene phenol formaldehyde. The arabinose ester was synthesized on the Petroleum Research Laboratory - UFRN, through enzymatic catalysis by protease from Bacillus subtilis, using arabinose and vegetable oil, in organic medium. In previous work [1], this sugar ester was evaluated as a possible water/oil demulsifier and the results were compared with the results of the commercial product based on poly-oxy alkylene phenol formaldehyde, showing that, for certain reaction conditions, the sugar ester presented better acting (71%) that the commercial product (33%) as demulsifier. In this work, the stability of this arabinose ester was evaluated in severe conditions of temperature, salinity and pH, through superficial tests in a tensiometer, using Wilhelmy plate method and the results were compared with the results obtained for two commercial products above mentioned. (author)

  2. Fatty acid methyl ester profiles of bat wing surface lipids.

    Science.gov (United States)

    Pannkuk, Evan L; Fuller, Nathan W; Moore, Patrick R; Gilmore, David F; Savary, Brett J; Risch, Thomas S

    2014-11-01

    Sebocytes are specialized epithelial cells that rupture to secrete sebaceous lipids (sebum) across the mammalian integument. Sebum protects the integument from UV radiation, and maintains host microbial communities among other functions. Native glandular sebum is composed primarily of triacylglycerides (TAG) and wax esters (WE). Upon secretion (mature sebum), these lipids combine with minor cellular membrane components comprising total surface lipids. TAG and WE are further cleaved to smaller molecules through oxidation or host enzymatic digestion, resulting in a complex mixture of glycerolipids (e.g., TAG), sterols, unesterified fatty acids (FFA), WE, cholesteryl esters, and squalene comprising surface lipid. We are interested if fatty acid methyl ester (FAME) profiling of bat surface lipid could predict species specificity to the cutaneous fungal disease, white nose syndrome (WNS). We collected sebaceous secretions from 13 bat spp. using Sebutape(®) and converted them to FAME with an acid catalyzed transesterification. We found that Sebutape(®) adhesive patches removed ~6× more total lipid than Sebutape(®) indicator strips. Juvenile eastern red bats (Lasiurus borealis) had significantly higher 18:1 than adults, but 14:0, 16:1, and 20:0 were higher in adults. FAME profiles among several bat species were similar. We concluded that bat surface lipid FAME profiling does not provide a robust model predicting species susceptibility to WNS. However, these results provide baseline data that can be used for lipid roles in future ecological studies, such as life history, diet, or migration.

  3. Analysis of phthalate esters contamination in drinking water samples ...

    African Journals Online (AJOL)

    The optimum condition method was successfully applied to the analysis of phthalate esters contamination in bottled drinking water samples. The concentration of DMP, DEP and DBP in drinking water samples were below allowable levels, while the DEHP concentration in three samples was found to be greater than the ...

  4. Controlled grafting of cellulose esters using SET-LRP process

    Czech Academy of Sciences Publication Activity Database

    Vlček, Petr; Raus, Vladimír; Janata, Miroslav; Kříž, Jaroslav; Sikora, Antonín

    2011-01-01

    Roč. 49, č. 1 (2011), s. 164-173 ISSN 0887-624X R&D Projects: GA ČR GA106/09/1348 Institutional research plan: CEZ:AV0Z40500505 Keywords : cellulose esters * copolymerization * graft copolymers Subject RIV: JI - Composite Materials Impact factor: 3.919, year: 2011

  5. Resveratrol inhibits phorbol ester-induced membrane translocation of presynaptic Munc13-1.

    Science.gov (United States)

    Pany, Satyabrata; Ghosh, Anamitra; You, Youngki; Nguyen, Nga; Das, Joydip

    2017-11-01

    Resveratrol (1) is a naturally occurring polyphenol that has been implicated in neuroprotection. One of resveratrol's several biological targets is Ca 2+ -sensitive protein kinase C alpha (PKCα). Resveratrol inhibits PKCα by binding to its activator-binding C1 domain. Munc13-1 is a C1 domain-containing Ca 2+ -sensitive SNARE complex protein essential for vesicle priming and neurotransmitter release. To test if resveratrol could also bind and inhibit Munc13-1, we studied the interaction of resveratrol and its derivatives, (E)-1,3-dimethoxy-5-(4-methoxystyryl)benzene, (E)-5,5'-(ethene-1,2-diyl)bis(benzene-1,2,3-triol), (E)-1,2-bis(3,4,5-trimethoxyphenyl)ethane, and (E)-5-(4-(hexadecyloxy)-3,5-dihydroxystyryl)benzene-1,2,3-triol with Munc13-1 by studying its membrane translocation from cytosol to plasma membrane in HT22 cells and primary hippocampal neurons. Resveratrol, but not the derivatives inhibited phorbol ester-induced Munc13-1 translocation from cytosol to membrane in HT22 cells and primary hippocampal neurons, as evidenced by immunoblot analysis and confocal microscopy. Resveratrol did not show any effect on Munc13-1 H567K , a mutant which is not sensitive to phorbol ester. Binding studies with Munc13-1 C1 indicated that resveratrol competes with phorbol ester for the binding site. Molecular docking and dynamics studies suggested that hydroxyl groups of resveratrol interact with phorbol-ester binding residues in the binding pocket. This study characterizes Munc13-1 as a target of resveratrol and highlights the importance of dietary polyphenol in the management of neurodegenerative diseases. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Synthesis and biological evaluation of arctigenin ester and ether derivatives as activators of AMPK.

    Science.gov (United States)

    Shen, Sida; Zhuang, Jingjing; Chen, Yijia; Lei, Min; Chen, Jing; Shen, Xu; Hu, Lihong

    2013-07-01

    A series of new arctigenin and 9-deoxy-arctigenin derivatives bearing different ester and ether side chains at the phenolic hydroxyl positions are designed, synthesized, and evaluated for activating AMPK potency in L6 myoblasts. Initial biological evaluation indicates that some alkyl ester and phenethyl ether arctigenin derivatives display potential activities in AMPK phosphorylation improvement. Further structure-activity relationship analysis shows that arctigenin ester derivatives 3a, 3h and 9-deoxy-arctigenin phenethyl ether derivatives 6a, 6c, 6d activate AMPK more potently than arctigenin. Moreover, the 2-(3,4-dimethoxyphenyl)ethyl ether moiety of 6c has been demonstrated as a potential functional group to improve the effect of AMPK phosphorylation. The structural optimization of arctigenin leads to the identification of 6c as a promising lead compound that exhibits excellent activity in AMPK activation. Copyright © 2013 The Authors. Published by Elsevier Ltd.. All rights reserved.

  7. Estimated U.S. infant exposures to 3-MCPD esters and glycidyl esters from consumption of infant formula.

    Science.gov (United States)

    Spungen, Judith H; MacMahon, Shaun; Leigh, Jessica; Flannery, Brenna; Kim, Grace; Chirtel, Stuart; Smegal, Deborah

    2018-04-05

    A dietary exposure assessment was conducted for 3-monochloropropane-1,2-diol (3-MCPD) esters (3-MCPDE) and glycidyl esters (GE) in infant formulas available for consumption in the U.S. 3-MCPDE and GE are food contaminants generated during the deodorization of refined edible oils, which are used in infant formulas and other foods. 3-MCPDE and GE are of potential toxicological concern because these compounds are metabolized to free 3-MCPD and free glycidol in rodents, and may have the same metabolic fate in humans. Free 3-MCPD and free glycidol have been found to cause adverse effects in rodents. Dietary exposures to 3-MCPDE and GE from consumption of infant formulas are of particular interest because formulas are the sole or primary food source for some infants. In this analysis, U.S. Food and Drug Administration (FDA) data on 3-MCPDE and GE concentrations (as 3-MCPD and glycidol equivalents, respectively) in a small convenience sample of infant formulas were used to estimate exposures from consumption of formula by infants 0 - 6 months of age. 3-MCPDE and GE exposures based on mean concentrations in all formulas were estimated at 7 - 10 µg/kg bw/day and 2 µg/kg bw/day, respectively. Estimated mean exposures from consumption of formulas produced by individual manufacturers ranged from 1 - 14 µg/kg bw/day for 3-MCPDE, and from 1 - 3 µg/kg for GE.

  8. Effect of surfactant and surfactant blends on pseudoternary phase diagram behavior of newly synthesized palm kernel oil esters

    Directory of Open Access Journals (Sweden)

    Mahdi ES

    2011-06-01

    Full Text Available Elrashid Saleh Mahdi1, Mohamed HF Sakeena1, Muthanna F Abdulkarim1, Ghassan Z Abdullah1,3, Munavvar Abdul Sattar2, Azmin Mohd Noor11Department of Pharmaceutical Technology, 2Department of Physiology, School of Pharmaceutical Sciences, Universiti Sains Malaysia, Minden, Penang, Malaysia; 3Department of Pharmaceutical Technology, International Medical University, Bukit Jalil, Kuala Lumpur, MalaysiaBackground: The purpose of this study was to select appropriate surfactants or blends of surfactants to study the ternary phase diagram behavior of newly introduced palm kernel oil esters.Methods: Nonionic surfactant blends of Tween® and Tween®/Span® series were screened based on their solubilization capacity with water for palm kernel oil esters. Tween® 80 and five blends of Tween® 80/Span® 80 and Tween® 80/Span® 85 in the hydrophilic-lipophilic balance (HLB value range of 10.7–14.0 were selected to study the phase diagram behavior of palm kernel oil esters using the water titration method at room temperature.Results: High solubilization capacity was obtained by Tween® 80 compared with other surfactants of Tween® series. High HLB blends of Tween® 80/Span® 85 and Tween® 80/Span® 80 at HLB 13.7 and 13.9, respectively, have better solubilization capacity compared with the lower HLB values of Tween® 80/Span® 80. All the selected blends of surfactants were formed as water-in-oil microemulsions, and other dispersion systems varied in size and geometrical layout in the triangles. The high solubilization capacity and larger areas of the water-in-oil microemulsion systems were due to the structural similarity between the lipophilic tail of Tween® 80 and the oleyl group of the palm kernel oil esters.Conclusion: This study suggests that the phase diagram behavior of palm kernel oil esters, water, and nonionic surfactants is not only affected by the HLB value, but also by the structural similarity between palm kernel oil esters and the surfactant

  9. Cholesteryl ester transfer activity in plasma measured by using solid-phase-bound high-density lipoprotein

    International Nuclear Information System (INIS)

    Sparks, D.L.; Frohlich, J.; Cullis, P.; Pritchard, P.H.

    1987-01-01

    We studied the ability of lipid-transfer factors in plasma to promote transfer, to endogenous lipoproteins, of [ 3 H]cholesteryl ester from high-density lipoprotein (HDL) covalently bound to Sepharose 4B beads. After incubation for 2 h at 37 degrees C, 12 to 14% of the [ 3 H]cholesteryl ester had been transferred to the lipoproteins of the plasma, in the proportions 57% to HDL and 43% to low- and very-low-density lipoproteins. This process was a function of the amount of plasma present and was stimulated by addition of partly purified lipid-transfer protein. Transfer also depended on the concentration of donor HDL but was independent of the amount of acceptor lipoprotein. This simple evaluation of cholesteryl ester transfer does not require removal of lipoproteins from the plasma before incubation

  10. Intrinsic terminators in Mycoplasma hyopneumoniae transcription.

    Science.gov (United States)

    Fritsch, Tiago Ebert; Siqueira, Franciele Maboni; Schrank, Irene Silveira

    2015-04-08

    Mycoplasma hyopneumoniae, an important pathogen of swine, exhibits a low guanine and cytosine (GC) content genome. M. hyopneumoniae genome is organised in long transcriptional units and promoter sequences have been mapped upstream of all transcription units. These analysis provided insights into the gene organisation and transcription initiation at the genome scale. However, the presence of transcriptional terminator sequences in the M. hyopneumoniae genome is poorly understood. In silico analyses demonstrated the presence of putative terminators in 82% of the 33 monocistronic units (mCs) and in 74% of the 116 polycistronic units (pCs) considering different classes of terminators. The functional activity of 23 intrinsic terminators was confirmed by RT-PCR and qPCR. Analysis of all terminators found by three software algorithms, combined with experimental results, allowed us to propose a pattern of RNA hairpin formation during the termination process and to predict the location of terminators in the M. hyopneumoniae genome sequence. The stem-loop structures of intrinsic terminators of mycoplasma diverge from the pattern of terminators found in other bacteria due the low content of guanine and cytosine. In M. hyopneumoniae, transcription can end after a transcriptional unit and before its terminator sequence and can also continue past the terminator sequence with RNA polymerases gradually releasing the RNA.

  11. Preparation and characterization of a novel hyperbranched polyphosphate ester

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Sufang [College of Chemistry, Chemical Engineering and Material Science, Soochow University, Suzhou, Jiangsu Province 215123 (China); Key Laboratory for Green Chemical Process of Ministry of Education, Wuhan Institute of Technology, Wuhan, Hubei 430073 (China); Zhang, Daohong, E-mail: zhangdh@163.com [Key Laboratory of Catalysis and Materials Science of the State Ethnic Affairs Commission and Ministry of Education, South-Central University for Nationalities, Wuhan, Hubei Province 430074 (China); Cheng, Xinjian; Li, Tingcheng; Zhang, Aiqing [Key Laboratory of Catalysis and Materials Science of the State Ethnic Affairs Commission and Ministry of Education, South-Central University for Nationalities, Wuhan, Hubei Province 430074 (China); Li, Jinlin [College of Chemistry, Chemical Engineering and Material Science, Soochow University, Suzhou, Jiangsu Province 215123 (China); Key Laboratory of Catalysis and Materials Science of the State Ethnic Affairs Commission and Ministry of Education, South-Central University for Nationalities, Wuhan, Hubei Province 430074 (China)

    2012-11-15

    Polyphosphate esters have received a great deal of attention due to their important application in biomaterials field. Hyperbranched structure of polymers may support unique properties, including low viscosity and perfect intrinsic property. We report here three generations of hyperbranched polyphosphate esters (HPPE-1, HPPE-2 and HPPE-3) synthesized from a dehydrochlorination reaction between 1,3,5-tris(2-hydroxyethyl)cyanuric acid (THEIC) and phosphorus oxychloride (POCl{sub 3}), and characterize their chemical structures by FT-IR, {sup 1}H NMR, {sup 13}C NMR, {sup 31}P NMR and 2D NMR ({sup 1}H,{sup 1}H-COSY and {sup 13}C, {sup 1}H-HSQC) techniques. Degrees of branching of HPPE-1, HPPE-2 and HPPE-3 are 0.90, 0.91 and 0.87 respectively from the calculation of their {sup 13}C NMR spectra. Molecular weights of HPPE-1, HPPE-2 and HPPE-3 are m/z 1530, 1768 and 2750 from their MALDI-TOF-MS spectra. Study on thermal degradation mechanism of the HPPE-2 by a 3D FT-IR/TG technology shows that there are two cracking processes of its molecular chains, including the thermal degradation of hydroxylethyl-ended groups, nitrogen heterocycle and -CH{sub 2}CH{sub 2}- groups of HPPE-2. -- Highlights: Black-Right-Pointing-Pointer We prepared three novel hyperbranched polyphosphate esters (HPPE-1, HPPE-2 and HPPE-3). Black-Right-Pointing-Pointer Their chemical structures were characterized by FT-IR, 1D NMR and 2D NMR techniques. Black-Right-Pointing-Pointer Their degrees of branching were over 0.87. Black-Right-Pointing-Pointer TG-FTIR was used to study thermal degradation mechanism of the HPPE-2.

  12. Solvent-Free Lipase-Catalyzed Synthesis of Technical-Grade Sugar Esters and Evaluation of Their Physicochemical and Bioactive Properties

    Directory of Open Access Journals (Sweden)

    Ran Ye

    2016-05-01

    Full Text Available Technical-grade oleic acid esters of sucrose and fructose were prepared using solvent-free biocatalysis at 65 °C, without any downstream purification applied, and their physicochemical and bioactivity-related properties were evaluated and compared to a commercially available sucrose laurate emulsifier. To increase the conversion of sucrose and fructose oleate, prepared previously using solvent-free lipase-catalyzed esterification catalyzed by Rhizomucor miehei lipase (81% and 83% ester, respectively, the enzymatic reaction conditions was continued using CaSO4 to control the reactor’s air headspace and a lipase (from Candida antarctica B with a hydrophobic immobilization matrix to provide an ultralow water activity, and high-pressure homogenation, to form metastable suspensions of 2.0–3.3 micron sized saccharide particles in liquid-phase reaction media. These measures led to increased ester content of 89% and 96% for reactions involving sucrose and fructose, respectively. The monoester content among the esters decreased from 90% to <70% due to differences in regioselectivity between the lipases. The resultant technical-grade sucrose and fructose lowered the surface tension to <30 mN/m, and possessed excellent emulsification capability and stability over 36 h using hexadecane and dodecane as oils, comparable to that of sucrose laurate and Tween® 80. The technical-grade sugar esters, particularly fructose oleate, more effectively inhibited gram-positive foodborne pathogens (Lactobacillus plantarum, Pediococcus pentosaceus and Bacillus subtilis. Furthermore, all three sugar esters displayed antitumor activity, particularly the two sucrose esters. This study demonstrates the importance of controlling the biocatalysts’ water activity to achieve high conversion, the impact of a lipase’s regioselectivity in dictating product distribution, and the use of solvent-free biocatalysis to important biobased surfactants useful in foods, cosmetics

  13. Deficient tyrosine phosphorylation of c-Cbl and associated proteins in phorbol ester-resistant EL4 mouse thymoma cells.

    Science.gov (United States)

    Luo, X; Sando, J J

    1997-05-02

    Two tyrosine phosphoproteins in phorbol ester-sensitive EL4 (S-EL4) mouse thymoma cells have been identified as the p120 c-Cbl protooncogene product and the p85 subunit of phosphatidylinositol 3-kinase. Tyrosine phosphorylation of p120 and p85 increased rapidly after phorbol ester stimulation. Phorbol ester-resistant EL4 (R-EL4) cells expressed comparable amounts of c-Cbl and phosphatidylinositol 3-kinase protein but greatly diminished tyrosine phosphorylation. Co-immunoprecipitation experiments revealed complexes of c-Cbl with p85, and of p85 with the tyrosine kinase Lck in phorbol ester-stimulated S-EL4 but not in unstimulated S-EL4 or in R-EL4 cells. In vitro binding of c-Cbl with Lck SH2 or SH3 domains was detected in both S-EL4 and R-EL4 cells, suggesting that c-Cbl, p85, and Lck may form a ternary complex. In vitro kinase assays revealed phosphorylation of p85 by Lck only in phorbol ester-stimulated S-EL4 cells. Collectively, these results suggest that Cbl-p85 and Lck-p85 complexes may form in unstimulated S-EL4 and R-EL4 cells but were not detected due to absence of tyrosine phosphorylation of p85. Greatly decreased tyrosine phosphorylation of c-Cbl and p85 in the complexes may contribute to the failure of R-EL4 cells to respond to phorbol ester.

  14. Mechanism of formation of 3-chloropropan-1,2-diol (3-MCPD) esters under conditions of the vegetable oil refining.

    Science.gov (United States)

    Šmidrkal, Jan; Tesařová, Markéta; Hrádková, Iveta; Berčíková, Markéta; Adamčíková, Aneta; Filip, Vladimír

    2016-11-15

    3-MCPD esters are contaminants that can form during refining of vegetable oils in the deodorization step. It was experimentally shown that their content in the vegetable oil depends on the acid value of the vegetable oil and the chloride content. 3-MCPD esters form approximately 2-5 times faster from diacylglycerols than from monoacylglycerols. It has been proved that the higher fatty acids content in the oil caused higher 3-MCPD esters content in the deodorization step. Neutralization of free fatty acids in the vegetable oil before the deodorization step by alkaline carbonates or hydrogen carbonates can completely suppress the formation of 3-MCPD esters. Potassium salts are more effective than sodium salts. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Studies of the X-ray absorption spectra of some methylcyano esters

    International Nuclear Information System (INIS)

    Takahashi, Osamu; Saito, Ko; Mitani, Masaki; Yoshida, Hiroaki; Tahara, Fumitaka; Sunami, Tetsuji; Waki, Keiichiro; Senba, Yasunori; Hiraya, Atsunari; Pettersson, Lars G.M.

    2005-01-01

    Density functional theory (DFT) has been applied to simulate core-excited photoabsorption spectra for some methylcyano esters within a transition potential (TP) framework. Our calculations for methylcyano formate at the N and O K-edges are consistent with previous experimental spectra. For methylcyano acetate the photoabsorption spectra at the N and O K-edges were reinvestigated experimentally. Contrary to the previous experiment, only one main peak was observed at the N K-edge and this peak was assigned to N(1s) ->π* excitation. This result was supported by our theoretical calculations. The general trends in the X-ray absorption spectra and the site-specific bond scission of methylcyano esters at the N and O K-edges are also discussed

  16. Combustion of jojoba methyl ester in an indirect injection diesel engine

    Energy Technology Data Exchange (ETDEWEB)

    Selim, M.Y.E. [United Arab Emirates University, Al-Ain (United Arab Emirates). Mechanical Engineering Dept.; Radwan, M.S.; Elfeky, S.M.S. [Helwan University, Cairo (Egypt). Mechanical Power Engineering Dept.

    2003-07-01

    An experimental investigation has been carried out to examine for the first time the performance and combustion noise of an indirect injection diesel engine running with new fuel derived from pure jojoba oil, jojoba methyl ester, and its blends with gas oil. A Ricardo E6 compression swirl diesel engine was fully instrumented for the measurement of combustion pressure and its rise rate and other operating parameters. Test parameters included the percentage of jojoba methyl ester in the blend, engine speed, load, injection timing and engine compression ratio. Results showed that the new fuel derived from jojoba is generally comparable and a good replacement to gas oil in diesel engine at most engine operating conditions, in terms of performance parameters and combustion noise produced. (author)

  17. 4-Hydroxy-3-methoxycinnamate esters of milkweed oil: synthesis and characterization.

    Science.gov (United States)

    Harry-O'kuru, Rogers E

    2005-11-01

    The common milkweed (Asclepias syriaca L.) is a new industrial crop. Its seed oil (TAG) is highly polyunsaturated. In the search for novel applications for milkweed seed oil, the olefinic groups in the TAG were oxidized to polyhydroxy TAG via epoxidation and subsequent epoxy ring-opening reactions. These polyhydroxy TAG exhibit unique industrially desirable emulsoid properties in water. Esterification of the secondary polyhydroxy functionalities of the TAG derivatives of the oil with trans-4-hydroxy-3-methoxycinnamic acid (ferulic acid) has resulted in the development of novel cinnamate esters of milkweed oil. These cinnamates are also obtainable via direct ring-opening of the epoxy TAG intermediate with ferulic acid. Among the interesting characteristics of the ester derivatives is their UV radiation-absorbing property.

  18. LNG TERMINAL SAFE OPERATION MANAGEMENT

    OpenAIRE

    Andrzej ADAMKIEWICZ; Włodzimierz KAMIŃSKI

    2012-01-01

    This article presents the significance of LNG terminal safety issues in natural gas sea transport. It shows particular requirements for LNG transmission installations resulting from the specific properties of LNG. Out of the multi‐layer critical safety areas comprising structural elements of the terminal safety system, possibilities to decrease the risk of emergency occurrence on LNG terminals have been selected. Tasks performed by the LNG terminal, together with its own personnel and the out...

  19. Cloning of the DNA-binding subunit of human nuclear factor κB: The level of its mRNA is strongly regulated by phorbol ester or tumor necrosis factor α

    International Nuclear Information System (INIS)

    Meyer, R.; Hatada, E.N.; Bartsch, C.; Scheidereit, C.; Hohmann, H.P.; Haiker, M.; Roethlisberger, U.; Lahm, H.W.; Schlaeger, E.J.; van Loon, A.P.G.M.

    1991-01-01

    The DNA binding subunit of nuclear factor κB (NF-κB), a B-cell protein that interacts with the immunoglobulin κ light-chain gene enhancer, has been purified from nuclei of human HL-60 cells stimulated with tumor necrosis factor α (TNFα), and internal peptide sequences were obtained. Overlapping cDNA clones were isolated and sequenced. The encoded open reading frame of about 105 kDa contained at its N-terminal half all six tryptic peptide sequences, suggesting that the 51-kDa NF-κB protein is processed from a 105-kDa precursor. An in vitro synthesized protein containing most of the N-terminal half of the open reading frame bound specifically to an NF-κB binding site. This region also showed high homology to a domain shared by the Drosophila dorsal gene and the avian and mammalian rel (proto)oncogene products. The level of the 3.8-kilobase mRNA was strongly increased after stimulation with TNFα or phorbol ester. Thus, both factors not only activate NF-κB protein, as described previously, but also induce expression of the gene encoding the DNA-binding subunit of NF-κB

  20. Preparation of Jojoba Oil Ester Derivatives for Biodiesel Evaluation

    Science.gov (United States)

    As a result of the increase in commodity vegetable oil prices, it is imperative that non-food oils should be considered as alternative feedstocks for biodiesel production. Jojoba oil is unusual in that it is comprised of wax esters as opposed to the triglycerides found in typical vegetable oils. A...

  1. Rapid Synthesis of Highly Monodisperse Au x Ag 1− x Alloy Nanoparticles via a Half-Seeding Approach

    KAUST Repository

    Chng, Ting Ting

    2011-05-03

    Gold-silver alloy AuxAg1-x is an important class of functional materials promising new applications across a wide array of technological fields. In this paper, we report a fast and facile synthetic protocol for preparation of highly monodisperse AuxAg1-x alloy nanoparticles in the size range of 3-6 nm. The precursors employed in this work are M(I)-alkanethiolates (M = Au and Ag), which can be easily prepared by mixing common chemicals such as HAuCl4 or AgNO3 with alkanethiols at room temperature. In this half-seeding approach, one of the M(I)-alkanethiolates is first heated and reduced in oleylamine solvent, and freshly formed metal clusters will then act as premature seeds on which both the first and second metals (from M(I)-alkanethiolates, M = Au and Ag) can grow accordingly without additional nucleation and thus achieve high monodispersity for product alloy nanoparticles. Unlike in other prevailing methods, both Au and Ag elements present in these solid precursors are in the same monovalent state and have identical supramolecular structures, which may lead to a more homogeneous reduction and complete interdiffusion at elevated reaction temperatures. When the M(I)-alkanethiolates are reduced to metallic forms, the detached alkanethiolate ligands will serve as capping agent to control the growth. More importantly, composition, particle size, and optical properties of AuxAg1-x alloy nanoparticles can be conveniently tuned with this approach. The optical limiting properties of the prepared particles have also been investigated at 532 and 1064 nm using 7 ns laser pulses, which reveals that the as-prepared alloy nanoparticles exhibit outstanding broadband optical limiting properties with low thresholds. © 2011 American Chemical Society.

  2. Termination unit

    Energy Technology Data Exchange (ETDEWEB)

    Traeholt, Chresten; Willen, Dag; Roden, Mark; Tolbert, Jerry C.; Lindsay, David; Fisher, Paul W.; Nielsen, Carsten Thidemann

    2016-05-03

    Cable end section comprises end-parts of N electrical phases/neutral, and a thermally-insulation envelope comprising cooling fluid. The end-parts each comprises a conductor and are arranged with phase 1 innermost, N outermost surrounded by the neutral, electrical insulation being between phases and N and neutral. The end-parts comprise contacting surfaces located sequentially along the longitudinal extension of the end-section. A termination unit has an insulating envelope connected to a cryostat, special parts at both ends comprising an adapter piece at the cable interface and a closing end-piece terminating the envelope in the end-section. The special parts houses an inlet and/or outlet for cooling fluid. The space between an inner wall of the envelope and a central opening of the cable is filled with cooling fluid. The special part at the end connecting to the cryostat houses an inlet or outlet, splitting cooling flow into cable annular flow and termination annular flow.

  3. Synthesis of Chiral, Enantiopure Allylic Amines by the Julia Olefination of α-Amino Esters.

    Science.gov (United States)

    Benedetti, Fabio; Berti, Federico; Fanfoni, Lidia; Garbo, Michele; Regini, Giorgia; Felluga, Fulvia

    2016-06-21

    The four-step conversion of a series of N-Boc-protected l-amino acid methyl esters into enantiopure N-Boc allylamines by a modified Julia olefination is described. Key steps include the reaction of a lithiated phenylalkylsulfone with amino esters, giving chiral β-ketosulfones, and the reductive elimination of related α-acetoxysulfones. The overall transformation takes place under mild conditions, with good yields, and without loss of stereochemical integrity, being in this respect superior to the conventional Julia reaction of α-amino aldehydes.

  4. Identification of 3-MCPD esters to verify the adulteration of extra virgin olive oil.

    Science.gov (United States)

    Hung, Wei-Ching; Peng, Guan-Jhih; Tsai, Wen-Ju; Chang, Mei-Hua; Liao, Chia-Ding; Tseng, Su-Hsiang; Kao, Ya-Min; Wang, Der-Yuan; Cheng, Hwei-Fang

    2017-09-01

    The adulteration of olive oil is an important issue around the world. This paper reports an indirect method by which to identify 3-monochloropropane-1,2-diol (3-MCPD) esters in olive oils. Following sample preparation, the samples were spiked with 1,2-bis-palmitoyl-3-chloropropanediol standard for analysis using gas chromatograph-tandem mass spectrometry. The total recovery ranged from 102.8% to 105.5%, the coefficient of variation ranged from 1.1% to 10.1%, and the limit of quantification was 0.125 mg/kg. The content of 3-MCPD esters in samples of refined olive oil (0.97-20.53 mg/kg) exceeded those of extra virgin olive oil (non-detected to 0.24 mg/kg). These results indicate that the oil refining process increased the content of 3-MCPD esters, which means that they could be used as a target compound for the differentiation of extra virgin olive oil from refined olive oil in order to prevent adulteration.

  5. Partial Reduction of Esters to Aldehydes Using a Novel Modified Red-Al Reducing Agent

    Energy Technology Data Exchange (ETDEWEB)

    Shin, Won Kyu; Kang, Daehoon; An, Duk Keun [Kangwon National Univ., Chunchon (Korea, Republic of)

    2014-07-15

    We have developed a convenient alternative method for the synthesis of aldehydes from both aromatic and aliphatic esters in very good to excellent yields in the absence of any additives using a modified Red-Al that was easily prepared by reacting commercially available Red-Al with cis-2,6-dimethyl morpholine. The advantages of the present methodology are as follows: simple preparation procedure of the reducing agent, improved product yields, convenient reaction temperature, and short reaction times. Therefore, the new reagent has great potential to be a useful alternative partial reducing agent for the synthesis of aldehydes from esters in organic synthesis. Aldehydes are valuable building blocks and reactive intermediates in organic synthesis. The general and classical syntheses of aldehydes from esters involve reduction-oxidation and partial reduction using efficient partial reducing agents. Obviously, one-step partial reduction methods are more useful than two-step reduction-oxidation methods owing to their simplicity, and generality in organic synthesis.

  6. Stereocontrolled reduction of alpha- and beta-keto esters with micro green algae, Chlorella strains.

    Science.gov (United States)

    Ishihara, K; Yamaguchi, H; Adachi, N; Hamada, H; Nakajima, N

    2000-10-01

    The stereocontrolled reduction of alpha- and beta-keto esters using micro green algae was accomplished by a combination of the cultivation method and the introduction of an additive. The reduction of ethyl pyruvate and ethyl benzoylformate by the photoautotrophically cultivated Chlorella sorokiniana gave the corresponding alcohol in high e.e. (>99% e.e. (S) and >99% e.e. (R), respectively). In the presence of glucose as an additive, the reduction of ethyl 3-methyl-2-oxobutanoate by the heterotrophically cultivated C. sorokiniana afforded the corresponding (R)-alcohol. On the other hand, the reduction in the presence of ethyl propionate gave the (S)-alcohol. Ethyl 2-methyl-3-oxobutanoate was reduced in the presence of glycerol by the photoautotrophically cultivated C. sorokiniana or the heterotrophically cultivated C. sorokiniana to the corresponding syn-(2R,3S)-hydroxy ester with high diastereo- and enantiomeric excess (e.e.). Some additives altered the stereochemical course in the reduction of alpha- and beta-keto esters.

  7. Base free aryl coupling of diazonium compounds and boronic esters: self-activation allowing an overall highly practical process.

    Science.gov (United States)

    Bonin, Hélène; Delbrayelle, Dominique; Demonchaux, Patrice; Gras, Emmanuel

    2010-04-21

    Boronic esters have long been considered as poor partners in cross-coupling reactions with arene diazoniums. Here is reported an unprecedented application of self-activated boronic esters in a base-free cross-coupling reaction with diazonium salts under mild and user friendly conditions.

  8. Polysaccharide esters and their use as binders in coatings

    NARCIS (Netherlands)

    Oostveen, E.A.; Weijnen, J.; Haveren, van J.; Gillard, M.

    2003-01-01

    The invention relates to a polyester obtainable by transesterification or interesterification of: (i) inulin of general formula G(F)n or an acyl ester thereof, wherein G represents a glucose moiety, F represents a fructose moiety, and n is at least 2, and(ii) a drying oil, a semi-drying oil or

  9. Phagocytosis of cholesteryl ester is amplified in diabetic mouse macrophages and is largely mediated by CD36 and SR-A.

    Directory of Open Access Journals (Sweden)

    Christopher B Guest

    Full Text Available Type 2 diabetes (T2D is associated with accelerated atherosclerosis, which accounts for approximately 75% of all diabetes-related deaths. Here we investigate the link between diabetes and macrophage cholesteryl ester accumulation. When diabetic (db/db mice are given cholesteryl ester intraperitoneally (IP, peritoneal macrophages (PerMPhis recovered from these animals showed a 58% increase in intracellular cholesteryl ester accumulation over PerMPhis from heterozygote control (db/+ mice. Notably, PerMPhi fluid-phase endocytosis and large particle phagocytosis was equivalent in db/+and db/db mice. However, IP administration of CD36 and SR-A blocking antibodies led to 37% and 25% reductions in cholesteryl ester accumulation in PerMPhi. Finally, in order to determine if these scavenger receptors (SRs were part of the mechanism responsible for the increased accumulation of cholesteryl esters observed in the diabetic mouse macrophages, receptor expression was quantified by flow cytometry. Importantly, db/db PerMPhis showed a 43% increase in CD36 expression and an 80% increase in SR-A expression. Taken together, these data indicate that direct cholesteryl ester accumulation in mouse macrophages is mediated by CD36 and SR-A, and the magnitude of accumulation is increased in db/db macrophages due to increased scavenger receptor expression.

  10. Influence of Grape Composition on Red Wine Ester Profile: Comparison between Cabernet Sauvignon and Shiraz Cultivars from Australian Warm Climate.

    Science.gov (United States)

    Antalick, Guillaume; Šuklje, Katja; Blackman, John W; Meeks, Campbell; Deloire, Alain; Schmidtke, Leigh M

    2015-05-13

    The relationship between grape composition and subsequent red wine ester profile was examined. Cabernet Sauvignon and Shiraz, from the same Australian very warm climate vineyard, were harvested at two different stages of maturity and triplicate wines were vinified. Grape analyses focused on nitrogen and lipid composition by measuring 18 amino acids by HPLC-FLD, 3 polyunsaturated fatty acids, and 6 C6-compounds derived from lipid degradation by GC-MS. Twenty esters and four higher alcohols were analyzed in wines by HS-SPME-GC-MS. Concentrations of the ethyl esters of branched acids were significantly affected by grape maturity, but the variations were inconsistent between cultivars. Small relative variations were observed between wines for ethyl esters of fatty acids, whereas higher alcohol acetates displayed the most obvious differences with concentrations ranging from 1.5- to 26-fold higher in Shiraz than in Cabernet Sauvignon wines regardless of the grape maturity. Grape analyses revealed the variations of wine ester composition might be related to specific grape juice nitrogen composition and lipid metabolism. To the authors' knowledge the present study is the first to investigate varietal differences in the ester profiles of Shiraz and Cabernet Sauvignon wines made with grapes harvested at different maturity stages.

  11. Organising pneumonia associated with fumaric acid ester treatment for psoriasis.

    LENUS (Irish Health Repository)

    Deegan, Alexander Paul

    2012-02-01

    INTRODUCTION: We present the case of a 49-year old male who presented with dyspnoea, cough, weight loss, night sweats and general malaise. He had been on treatment with oral fumaric acid esters (FAE, Fumaderm(R); Biogen Idec GmbH, Ismaning, Germany) for 6 months. METHODS: Report of a case. RESULTS: His chest X-ray showed patchy infiltrates in the left upper lobe which failed to resolve under empiric antibiotic therapy. A computed tomography of thorax revealed bilateral, mostly peripheral foci of consolidation with air bronchograms. Transbronchial biopsies showed a pattern of organising pneumonia (OP). CONCLUSIONS: Therapy with oral prednisolone (40 mg\\/day) resulted in a rapid clinical and radiological improvement. An association of FAE and OP has not previously been reported. Please cite this paper as: Deegan AP, Kirby B, Rogers S, Crotty TB and McDonnell TJ. Organising pneumonia associated with fumaric acid ester treatment for psoriasis.

  12. Functional expression and characterization of five wax ester synthases in Saccharomyces cerevisiae and their utility for biodiesel production

    Directory of Open Access Journals (Sweden)

    Shi Shuobo

    2012-02-01

    Full Text Available Abstract Background Wax ester synthases (WSs can synthesize wax esters from alcohols and fatty acyl coenzyme A thioesters. The knowledge of the preferred substrates for each WS allows the use of yeast cells for the production of wax esters that are high-value materials and can be used in a variety of industrial applications. The products of WSs include fatty acid ethyl esters, which can be directly used as biodiesel. Results Here, heterologous WSs derived from five different organisms were successfully expressed and evaluated for their substrate preference in Saccharomyces cerevisiae. We investigated the potential of the different WSs for biodiesel (that is, fatty acid ethyl esters production in S. cerevisiae. All investigated WSs, from Acinetobacter baylyi ADP1, Marinobacter hydrocarbonoclasticus DSM 8798, Rhodococcus opacus PD630, Mus musculus C57BL/6 and Psychrobacter arcticus 273-4, have different substrate specificities, but they can all lead to the formation of biodiesel. The best biodiesel producing strain was found to be the one expressing WS from M. hydrocarbonoclasticus DSM 8798 that resulted in a biodiesel titer of 6.3 mg/L. To further enhance biodiesel production, acetyl coenzyme A carboxylase was up-regulated, which resulted in a 30% increase in biodiesel production. Conclusions Five WSs from different species were functionally expressed and their substrate preference characterized in S. cerevisiae, thus constructing cell factories for the production of specific kinds of wax ester. WS from M. hydrocarbonoclasticus showed the highest preference for ethanol compared to the other WSs, and could permit the engineered S. cerevisiae to produce biodiesel.

  13. [Determination of fatty acid esters of chloropropanediols in diet samples by gas chromatography-mass spectrometry coupled with solid-supported liquid-liquid extraction].

    Science.gov (United States)

    Gao, Jie; Liu, Qing; Han, Feng; Miao, Hong; Zhao, Yunfeng; Wu, Yongning

    2014-05-01

    To establish a method for the determination of fatty acid esters of 3-monochloropropane-1, 2-diol (3-MCPD) and 2-monochloropropane-1, 3-diol (2-MCPD) in diet samples by gas chromatography-mass spectrometry (GC-MS) with solid-supported liquid-liquid extraction (SLE). Diet samples were ultrasonically extracted by hexane, followed by ester cleavage reaction with sodium methylate in methanol, and then purified by solid-supported liquid-liquid extraction. (SLE) using diatomaceous earth as the sorbent. After derivatization with heptafluorobutyrylimidazole, the analytes were detected by GC-MS and quantified by the deuterated internal standards. The limits of detection (LODs) of 3-MCPD esters and 2-MCPD esters in different diet samples were 0.002 - 0.005 mg/kg and 0.002 - 0.006 mg/kg. The average recoveries of 3-MCPD esters and 2-MCPD esters at the spiking levels of 0.05 and 0.1 mg/kg in the diet samples were in the range of 65.9% - 104.2% and 75.4% - 118.0%, respectively, with the relative standard deviations in the range of 2.2% - 14.2% and 0.8% - .13.9%. The method is simple, accurate and rugged for the determination of fatty acid esters of 3-MCPD and 2-MCPD in diet samples.

  14. Analysis of phthalate ester content in poly(vinyl chloride) plastics by means of Fourier transform Raman spectroscopy

    DEFF Research Database (Denmark)

    Nørbygaard, Thomas; Berg, Rolf W.

    2004-01-01

    Fourier transform (FT) Raman spectroscopy is applied to a range of phthalate ester plasticizers in pure form as well as in poly(vinyl chloride) (PVC) samples. It is found that phthalate esters as a group can be identified by a set of six characteristic Raman bands. FT-Raman spectra of 22 phthalate...

  15. Transesterification of mustard (Brassica nigra) seed oil with ethanol: Purification of the crude ethyl ester with activated carbon produced from de-oiled cake

    International Nuclear Information System (INIS)

    Fadhil, Abdelrahman B.; Abdulahad, Waseem S.

    2014-01-01

    Highlights: • Biodiesel ethyl ester has been developed from mustard seed oil. • Variables affect the transesterification were investigated. • Dry washing using the activated carbon produced from the extraction remaining was applied to purify the ethyl esters. • Properties of the produced fuels were measured. • Blending of the produced ethyl ester with petro diesel was also investigated. - Abstract: The present study reports the production of mustard seed oil ethyl esters (MSOEE) through alkali-catalyzed transesterification with ethanol using potassium hydroxide as a catalyst. The influence of the process parameters such as catalyst concentration, ethanol to oil molar ratio, reaction temperature, reaction duration and the catalyst type was investigated so as to find out the optimal conditions for the transesterification process. As a result, optimum conditions for production of MSOEE were found to be: 0.90% KOH wt/wt of oil, 8:1 ethanol to oil molar ratio, a reaction temperature of 60 °C, and a reaction time of 60 min. Dry washing method with (2.50% wt.) of the activated carbon that was produced from the de-oiled cake was used to purify the crude ethyl ester from the residual catalyst and glycerol. The transesterification process provided a yield of 94% w/w of ethyl esters with an ester content of 98.22% wt. under the optimum conditions. Properties of the produced ethyl esters satisfied the specifications prescribed by the ASTM standards. Blending MSOEE with petro diesel was also investigated. The results showed that the ethyl esters had a slight influence on the properties of petro diesel

  16. Synthesis of Chiral, Enantiopure Allylic Amines by the Julia Olefination of α-Amino Esters

    Directory of Open Access Journals (Sweden)

    Fabio Benedetti

    2016-06-01

    Full Text Available The four-step conversion of a series of N-Boc-protected l-amino acid methyl esters into enantiopure N-Boc allylamines by a modified Julia olefination is described. Key steps include the reaction of a lithiated phenylalkylsulfone with amino esters, giving chiral β-ketosulfones, and the reductive elimination of related α-acetoxysulfones. The overall transformation takes place under mild conditions, with good yields, and without loss of stereochemical integrity, being in this respect superior to the conventional Julia reaction of α-amino aldehydes.

  17. klax Terminal Aerodrome Forecast

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TAF (terminal aerodrome forecast or terminal area forecast) is a format for reporting weather forecast information, particularly as it relates to aviation. TAFs are...

  18. kprc Terminal Aerodrome Forecast

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TAF (terminal aerodrome forecast or terminal area forecast) is a format for reporting weather forecast information, particularly as it relates to aviation. TAFs are...

  19. katl Terminal Aerodrome Forecast

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TAF (terminal aerodrome forecast or terminal area forecast) is a format for reporting weather forecast information, particularly as it relates to aviation. TAFs are...

  20. kmcn Terminal Aerodrome Forecast

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — TAF (terminal aerodrome forecast or terminal area forecast) is a format for reporting weather forecast information, particularly as it relates to aviation. TAFs are...