40 CFR 792.61 - Equipment design.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 31 2010-07-01 2010-07-01 true Equipment design. 792.61 Section 792.61...) GOOD LABORATORY PRACTICE STANDARDS Equipment § 792.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

40 CFR 160.61 - Equipment design.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Equipment design. 160.61 Section 160... LABORATORY PRACTICE STANDARDS Equipment § 160.61 Equipment design. Equipment used in the generation... appropriate design and adequate capacity to function according to the protocol and shall be suitably located...

21 CFR 58.61 - Equipment design.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 1 2010-04-01 2010-04-01 false Equipment design. 58.61 Section 58.61 Food and... PRACTICE FOR NONCLINICAL LABORATORY STUDIES Equipment § 58.61 Equipment design. Equipment used in the... of appropriate design and adequate capacity to function according to the protocol and shall be...

Design guidelines for multi-seam mining at Elliot Lake

International Nuclear Information System (INIS)

Hedley, D.G.F.

1978-04-01

With the current expansion in uranium mining, multi-seam mining could again be practised at Elliot Lake as it was in the 1960s. Information on the dimensions of stopes, pillars, and parting zone was gathered from plans and sections of the relevant closed mines. Discussions were held with personnel familiar with these mines to establish instances of pillar, roof, and parting zone failures. Design guidelines are formulated for stope and pillar dimensions in multi-seam mining for a range of orebody configurations using past practice in a back-analysis approach. Constraints imposed by dip and seam thickness on the choice of equipment and mining layout are evaluated. An attempt is made to bring together the engineering aspects, including rock mechanics, of multi-seam mine design with uranium recovery and other economic factors for three alternative mine layouts: single-seam mining, double-seam mining, and seams-and-parting mining. A series of examples are worked through, showing how the design guidelines can be applied for typical orebody configurations

Sustainable design guidelines to support the Washington State ferries terminal design manual : design guideline application and refinement.

Science.gov (United States)

2013-08-01

The Sustainable Design Guidelines were developed in Phase I of this research program (WA-RD : 816.1). Here we are reporting on the Phase II effort that beta-tested the Phase I Guidelines on : example ferry terminal designs and refinements made ...

Recommended practices and guidelines for procurement of magnetic-fusion-energy electrical equipment

International Nuclear Information System (INIS)

1982-06-01

The followng three chapters are included: (1) administrative guidelines, (2) technical practices, and (3) check list. The first two chapters contain detailed information which is to be used as a reference by specification writers in preparing specifications. Chapter 3 is intended to provide a uniform specification format for specification writers, and is further intended to satisfy equipment manufactures' complaints that different specification formats are used to describe essentially identical equipment

Seismic design of equipment and piping systems for nuclear power plants in Japan

International Nuclear Information System (INIS)

Minematsu, Akiyoshi

1997-01-01

The philosophy of seismic design for nuclear power plant facilities in Japan is based on 'Examination Guide for Seismic Design of Nuclear Power Reactor Facilities: Nuclear Power Safety Committee, July 20, 1981' (referred to as 'Examination Guide' hereinafter) and the present design criteria have been established based on the survey of governmental improvement and standardization program. The detailed design implementation procedure is further described in 'Technical Guidelines for Aseismic Design of Nuclear Power Plants, JEAG4601-1987: Japan Electric Association'. This report describes the principles and design procedure of the seismic design of equipment/piping systems for nuclear power plant in Japan. (J.P.N.)

Seismic design of equipment and piping systems for nuclear power plants in Japan

Energy Technology Data Exchange (ETDEWEB)

Minematsu, Akiyoshi [Tokyo Electric Power Co., Inc. (Japan)

1997-03-01

The philosophy of seismic design for nuclear power plant facilities in Japan is based on `Examination Guide for Seismic Design of Nuclear Power Reactor Facilities: Nuclear Power Safety Committee, July 20, 1981` (referred to as `Examination Guide` hereinafter) and the present design criteria have been established based on the survey of governmental improvement and standardization program. The detailed design implementation procedure is further described in `Technical Guidelines for Aseismic Design of Nuclear Power Plants, JEAG4601-1987: Japan Electric Association`. This report describes the principles and design procedure of the seismic design of equipment/piping systems for nuclear power plant in Japan. (J.P.N.)

Design Guidelines for Low Crested Structures

DEFF Research Database (Denmark)

Burcharth, H. F.; Lamberti, Alberto

2004-01-01

1998-2002. The Guidelines comprise engineering aspects related to morphological impact and structure stability, biological aspects related to ecological impact, and socio-economical aspects related to the implementation of LCS-schemes. The guidelines are limited to submerged and regularly overtopped......The paper presents an overview of the design guidelines for low crested structures (LCS's) to be applied in coastal protection schemes. The design guidelines are formulated as a part of the research project: Environmental Design of Low Crested Coastal Defence Structures (DELOS) within the EC 5FP...

Equipment design guidance document for flammable gas waste storage tank new equipment

International Nuclear Information System (INIS)

Smet, D.B.

1996-01-01

This document is intended to be used as guidance for design engineers who are involved in design of new equipment slated for use in Flammable Gas Waste Storage Tanks. The purpose of this document is to provide design guidance for all new equipment intended for application into those Hanford storage tanks in which flammable gas controls are required to be addressed as part of the equipment design. These design criteria are to be used as guidance. The design of each specific piece of new equipment shall be required, as a minimum to be reviewed by qualified Unreviewed Safety Question evaluators as an integral part of the final design approval. Further Safety Assessment may be also needed. This guidance is intended to be used in conjunction with the Operating Specifications Documents (OSDs) established for defining work controls in the waste storage tanks. The criteria set forth should be reviewed for applicability if the equipment will be required to operate in locations containing unacceptable concentrations of flammable gas

D 59 Design Guidelines

DEFF Research Database (Denmark)

Burcharth, Hans F.; Lamberti, Alberto

The present guidelines are specifically dedicated to Low Crested Structures on attempt to provide methodological tools both for the engineering design of structures and for prediction of performance and environmental impacts. It is anticipated that the guidelines will provide valuable inputs to c...

Recommendations to the NRC on human engineering guidelines for nuclear power plant maintainability

Energy Technology Data Exchange (ETDEWEB)

Badalamente, R.V.; Fecht, B.A.; Blahnik, D.E.; Eklund, J.D.; Hartley, C.S.

1986-03-01

This document contains human engineering guidelines which can enhance the maintainability of nuclear power plants. The guidelines have been derived from general human engineering design principles, criteria, and data. The guidelines may be applied to existing plants as well as to plants under construction. They apply to nuclear power plant systems, equipment and facilities, as well as to maintenance tools and equipment. The guidelines are grouped into seven categories: accessibility and workspace, physical environment, loads and forces, maintenance facilities, maintenance tools and equipment, operating equipment design, and information needs. Each chapter of the document details specific maintainability problems encountered at nuclear power plants, the safety impact of these problems, and the specific maintainability design guidelines whose application can serve to avoid these problems in new or existing plants.

Recommendations to the NRC on human engineering guidelines for nuclear power plant maintainability

International Nuclear Information System (INIS)

Badalamente, R.V.; Fecht, B.A.; Blahnik, D.E.; Eklund, J.D.; Hartley, C.S.

1986-03-01

This document contains human engineering guidelines which can enhance the maintainability of nuclear power plants. The guidelines have been derived from general human engineering design principles, criteria, and data. The guidelines may be applied to existing plants as well as to plants under construction. They apply to nuclear power plant systems, equipment and facilities, as well as to maintenance tools and equipment. The guidelines are grouped into seven categories: accessibility and workspace, physical environment, loads and forces, maintenance facilities, maintenance tools and equipment, operating equipment design, and information needs. Each chapter of the document details specific maintainability problems encountered at nuclear power plants, the safety impact of these problems, and the specific maintainability design guidelines whose application can serve to avoid these problems in new or existing plants

FDH radiological design review guidelines

International Nuclear Information System (INIS)

Millsap, W.J.

1998-01-01

These guidelines discuss in more detail the radiological design review process used by the Project Hanford Management Contractors as described in HNF-PRO-1622, Radiological Design Review Process. They are intended to supplement the procedure by providing background information on the design review process and providing a ready source of information to design reviewers. The guidelines are not intended to contain all the information in the procedure, but at points, in order to maintain continuity, they contain some of the same information

FDH radiological design review guidelines

Energy Technology Data Exchange (ETDEWEB)

Millsap, W.J.

1998-09-29

These guidelines discuss in more detail the radiological design review process used by the Project Hanford Management Contractors as described in HNF-PRO-1622, Radiological Design Review Process. They are intended to supplement the procedure by providing background information on the design review process and providing a ready source of information to design reviewers. The guidelines are not intended to contain all the information in the procedure, but at points, in order to maintain continuity, they contain some of the same information.

Design, manufacture and installation of measuring and control equipments for the advanced thermal prototype reactor 'Fugen'

International Nuclear Information System (INIS)

Hirota, Shigeo; Kawabata, Yoshinori

1979-01-01

The advanced thermal prototype reactor ''Fugen'' attained the criticality on March 20, 1978, and 100% output operation on November 13, 1978. On March 20, 1979, it passed the final inspection, and since then, it has continued the smooth operation up to now. The measuring and control equipments are provided for grasping the operational conditions of the plant and operating it safely and efficiently. At the time of designing, manufacturing and installing the measuring and control equipments for Fugen, it was required to clarify the requirements of the plant design, to secure the sufficient functions, and to improve the operational process, maintainability and the reliability and accuracy of the equipments. Many design guidelines and criteria were decided in order to coordinate the conditions among five manufacturers and give the unified state as one plant. The outline of the instrumentations for neutrons, radiation monitoring and process data, the control systems for reactivity, reactor output, pressure and water supply, the safety protection system, and the process computer are described. Finally, the installations and tests of the measuring and control equipments are explained. The aseismatic capability of the equipments was confirmed. (Kako, I.)

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1992-07-01

The document reproduces the text of the notes verbales dated 15 May 1992, received by the Director General from the Resident Representatives to the Agency of Australia, Austria, Belgium, Bulgaria, Canada, Czech and Slovak Federal Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, Luxembourg, Netherlands, Norway, Poland, Portugal, Romania, Russia Federation, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to the export of nuclear material, equipment and technology and the Guidelines for Transfer of Nuclear-Related Dual-Use Equipment, Material and Related Technology. An Annex to these Guidelines contains the list of Nuclear-Related Dual-Use Equipment and Materials and Related Technology

Hot conditioning equipment conceptual design report

International Nuclear Information System (INIS)

Bradshaw, F.W.

1996-01-01

This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage

Hot conditioning equipment conceptual design report

Energy Technology Data Exchange (ETDEWEB)

Bradshaw, F.W., Westinghouse Hanford

1996-08-06

This report documents the conceptual design of the Hot Conditioning System Equipment. The Hot conditioning System will consist of two separate designs: the Hot Conditioning System Equipment; and the Hot Conditioning System Annex. The Hot Conditioning System Equipment Design includes the equipment such as ovens, vacuum pumps, inert gas delivery systems, etc.necessary to condition spent nuclear fuel currently in storage in the K Basins of the Hanford Site. The Hot Conditioning System Annex consists of the facility of house the Hot Conditioning System. The Hot Conditioning System will be housed in an annex to the Canister Storage Building. The Hot Conditioning System will consist of pits in the floor which contain ovens in which the spent nuclear will be conditioned prior to interim storage.

Advanced lighting guidelines: 1993. Final report

Energy Technology Data Exchange (ETDEWEB)

Eley, C.; Tolen, T.M. [Eley Associates, San Francisco, CA (United States); Benya, J.R. [Luminae Souter Lighting Design, San Francisco, CA (United States); Rubinstein, F.; Verderber, R. [Lawrence Berkeley Lab., CA (United States)

1993-12-31

The 1993 Advanced Lighting Guidelines document consists of twelve guidelines that provide an overview of specific lighting technologies and design application techniques utilizing energy-efficient lighting practice. Lighting Design Practice assesses energy-efficient lighting strategies, discusses lighting issues, and explains how to obtain quality lighting design and consulting services. Luminaires and Lighting Systems surveys luminaire equipment designed to take advantage of advanced technology lamp products and includes performance tables that allow for accurate estimation of luminaire light output and power input. The additional ten guidelines -- Computer-Aided Lighting Design, Energy-Efficient Fluorescent Ballasts, Full-Size Fluorescent Lamps, Compact Fluorescent Lamps, Tungsten-Halogen Lamps, Metal Halide and HPS Lamps, Daylighting and Lumen Maintenance, Occupant Sensors, Time Scheduling Systems, and Retrofit Control Technologies -- each provide a product technology overview, discuss current products on the lighting equipment market, and provide application techniques. This document is intended for use by electric utility personnel involved in lighting programs, lighting designers, electrical engineers, architects, lighting manufacturers` representatives, and other lighting professionals.

Design by analysis of composite pressure equipment

International Nuclear Information System (INIS)

Durand, S.; Mallard, H.

2004-01-01

Design by analysis has been particularly pointed out by the european pressure equipment directive. Advanced mechanical analysis like finite element method are used instead of classical design by formulas or graphs. Structural behaviour can be understood by the designer. Design by analysis of metallic pressure equipments is widely used. Material behaviour or limits analysis is based on sophisticated approach (elasto-plastic analysis,..). Design by analysis of composite pressure equipments is not systematically used for industrial products. The difficulty comes from the number of information to handle. The laws of mechanics are the same for composite materials than for steel. The authors want to show that in design by analysis, the composite material approach is only more complete than the metallic approach. Mechanics is more general but not more complicated. A multi-material approach is a natural evolution of design by analysis of composite equipments. The presentation is illustrated by several industrial cases - composite vessel: analogy with metallic calculations; - composite pipes and fittings; - welding and bounding of thermoplastic equipments. (authors)

Height, fun and safety in the design of children's playground equipment.

Science.gov (United States)

Wakes, Sarah; Beukes, Amanda

2012-01-01

The study reported in this paper adopted a holistic design approach to investigate issues associated with height related playground injuries from a users' perspective. The main objective was to gain an understanding of the relationship between height and fun so as to establish practical guidelines for addressing the causes of height related injuries whilst maintaining the attributes of playground equipment that children find fun and challenging. Results show that, on the one hand, the risk of injury increases when height is coupled with the use of upper body strength and, on the other hand, that coordination is a greater source of fun and challenge than height for children. Accordingly, it is suggested that the level of risk of injury attached to children's playground equipment can be reduced when the use of lower body strength and coordination are combined with lower free fall heights.

Advanced human-system interface design review guidelines

International Nuclear Information System (INIS)

O'Hara, J.M.

1990-01-01

Advanced, computer-based, human-system interface designs are emerging in nuclear power plant control rooms as a result of several factors. These include: (1) incorporation of new systems such as safety parameter display systems, (2) backfitting of current control rooms with new technologies when existing hardware is no longer supported by equipment vendors, and (3) development of advanced control room concepts. Control rooms of the future will be developed almost exclusively with advanced instrumentation and controls based upon digital technology. In addition, the control room operator will be interfacing with more intelligent systems which will be capable of providing information processing support to the operator. These developments may have significant implications for plant safety in that they will greatly affect the operator's role in the system as well as the ways in which he interacts with it. At present, however, the only guidance available to the Nuclear Regulatory Commission (NRC) for the review of control room-operator interfaces is NUREG-0700. It is a document which was written prior to these technological changes and is, therefore, tailored to the technologies used in traditional control rooms. Thus, the present guidance needs to be updated since it is inadequate to serve as the basis for NRC staff review of such advanced or hybrid control room designs. The objective of the project reported in this paper is to develop an Advanced Control Room Design Review Guideline suitable for use in performing human factors reviews of advanced operator interfaces. This guideline will take the form of a portable, interactive, computer-based document that may be conveniently used by an inspector in the field, as well as a text-based document

An approach to human-centered design of nuclear medical equipment: the system of caption of the thyroid

International Nuclear Information System (INIS)

Santos, Isaac J.A. Luquetti; Silva, Carlos Borges da; Santana, Marcos; Carvalho, Paulo Victor R.; Oliveira, Mauro Vitor de; Mol, Antonio Carlos Mol; Grecco, Claudio Henrique; Augusto, Silas Cordeiro

2005-01-01

Technology plays an important role in modern medical centers, making health care increasingly complex, relying on complex technical equipment. This technical complexity is particularly noticeable in the nuclear medicine and can increase the risks for human error. Human error has many causes such as performance shaping factors, organizational factors and user interface design. Poorly design human system interfaces of nuclear medical equipment can increase the risks for human error. If all nuclear medical equipment had been designed with good user interfaces, incidents and accidents could be reduced as well as he time required to learn how to use the equipment. Although some manufacturers of nuclear medical equipment have already integrate human factors principles in their products, there is still a need to steer the development of nuclear medical technology toward more human-centered approach. The aim of this paper is to propose a methodology that contributes to the design, development and evaluation of nuclear medical equipment and human system interface, towards a human-centered approach. This methodology includes the ergonomic approach, based on the operator activity analysis, together with human factors standards and guidelines, questionnaires and user based testing. We describe a case study in which this methodology is being applied in evaluation of the thyroid uptake system, getting essential information and data, that ill be used in development of a new system. (author)

Communication Received from the PermanentMission of Mexico to the International Atomic Energy Agency Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology and the Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-06-19

The Director General has received a note verbale dated 15 June 2012 from the Permanent Mission of Mexico to the International Atomic Energy Agency providing information on the decision of the Government of Mexico to act in accordance with the 'Guidelines for the Export of Nuclear Material, Equipment and Technology', issued as document INFCIRC/254/Rev.10/Part 1, including its Annexes, and with the 'Guidelines for Transfers of Nuclear-Related Dual-Use Equipment, Material, Software and Related Technology', issued as document INFCIRC/254/Rev.8/Part 2.

Communication Received from the Permanent Mission of Mexico to the International Atomic Energy Agency Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology and the Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2012-06-19

The Director General has received a note verbale dated 15 June 2012 from the Permanent Mission of Mexico to the International Atomic Energy Agency providing information on the decision of the Government of Mexico to act in accordance with the 'Guidelines for the Export of Nuclear Material, Equipment and Technology', issued as document INFCIRC/254/Rev.10/Part 1, including its Annexes, and with the 'Guidelines for Transfers of Nuclear-Related Dual-Use Equipment, Material, Software and Related Technology', issued as document INFCIRC/254/Rev.8/Part 2.

Communication Received from the Permanent Mission of Mexico to the International Atomic Energy Agency Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology and the Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology

International Nuclear Information System (INIS)

2012-01-01

The Director General has received a note verbale dated 15 June 2012 from the Permanent Mission of Mexico to the International Atomic Energy Agency providing information on the decision of the Government of Mexico to act in accordance with the 'Guidelines for the Export of Nuclear Material, Equipment and Technology', issued as document INFCIRC/254/Rev.10/Part 1, including its Annexes, and with the 'Guidelines for Transfers of Nuclear-Related Dual-Use Equipment, Material, Software and Related Technology', issued as document INFCIRC/254/Rev.8/Part 2

Communication Received from the PermanentMission of Mexico to the International Atomic Energy Agency Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology and the Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology

International Nuclear Information System (INIS)

2012-01-01

The Director General has received a note verbale dated 15 June 2012 from the Permanent Mission of Mexico to the International Atomic Energy Agency providing information on the decision of the Government of Mexico to act in accordance with the 'Guidelines for the Export of Nuclear Material, Equipment and Technology', issued as document INFCIRC/254/Rev.10/Part 1, including its Annexes, and with the 'Guidelines for Transfers of Nuclear-Related Dual-Use Equipment, Material, Software and Related Technology', issued as document INFCIRC/254/Rev.8/Part 2

Designing Instructional Materials: Some Guidelines.

Science.gov (United States)

Burbank, Lucille; Pett, Dennis

Guidelines for the design of instructional materials are outlined in this paper. The principles of design are presented in five major categories: (1) general design (structural appeal and personal appeal); (2) instructional design (attention, memory, concept learning, and attitude change); (3) visual design (media considerations, pictures, graphs…

Designing algorithm visualization on mobile platform: The proposed guidelines

Science.gov (United States)

Supli, A. A.; Shiratuddin, N.

2017-09-01

This paper entails an ongoing study about the design guidelines of algorithm visualization (AV) on mobile platform, helping students learning data structures and algorithm (DSA) subject effectively. Our previous review indicated that design guidelines of AV on mobile platform are still few. Mostly, previous guidelines of AV are developed for AV on desktop and website platform. In fact, mobile learning has been proved to enhance engagement in learning circumstances, and thus effect student's performance. In addition, the researchers highly recommend including UI design and Interactivity in designing effective AV system. However, the discussions of these two aspects in previous AV design guidelines are not comprehensive. The UI design in this paper describes the arrangement of AV features in mobile environment, whereas interactivity is about the active learning strategy features based on learning experiences (how to engage learners). Thus, this study main objective is to propose design guidelines of AV on mobile platform (AVOMP) that entails comprehensively UI design and interactivity aspects. These guidelines are developed through content analysis and comparative analysis from various related studies. These guidelines are useful for AV designers to help them constructing AVOMP for various topics on DSA.

Demarcating Mobile Phone Interface Design Guidelines to Expedite Selection

Directory of Open Access Journals (Sweden)

Karen Vera Renaud

2017-12-01

Full Text Available Guidelines are recommended as a tool for informing user interface design. Despite a proliferation of guidelines in the research literature, there is little evidence of their use in industry, nor their influence in academic literature. In this paper, we explore the research literature related to mobile phone design guidelines to find out why this should be so. We commenced by carrying out a scoping literature review of the mobile phone design guideline literature to gain insight into the maturity of the field. The question we wanted to explore was: “Are researchers building on each others’ guidelines, or is the research field still in the foundational stage?” We discovered a poorly structured field, with many researchers proposing new guidelines, but little incremental refinement of extant guidelines. It also became clear that the current reporting of guidelines did not explicitly communicate their multi-dimensionality or deployment context. This leaves designers without a clear way of discriminating between guidelines, and could contribute to the lack of deployment we observed. We conducted a thematic analysis of papers identified by means of a systematic literature review to identify a set of dimensions of mobile phone interface design guidelines. The final dimensions provide a mechanism for differentiating guidelines and expediting choice.

Design and evaluation guidelines for Department of Energy facilities subjected to natural phenomena hazards

International Nuclear Information System (INIS)

Kennedy, R.P.; Short, S.A.; McDonald, J.R.; McCann, M.W. Jr.; Murray, R.C.; Hill, J.R.

1990-06-01

The Department of Energy (DOE) and the DOE Natural Phenomena Hazards Panel have developed uniform design and evaluation guidelines for protection against natural phenomena hazards at DOE sites throughout the United States. The goal of the guidelines is to assure that DOE facilities can withstand the effects of natural phenomena such as earthquakes, extreme winds, tornadoes, and flooding. The guidelines apply to both new facilities (design) and existing facilities (evaluation, modification, and upgrading). The intended audience is primarily the civil/structural or mechanical engineers conducting the design or evaluation of DOE facilities. The likelihood of occurrence of natural phenomena hazards at each DOE site has been evaluated by the DOE Natural Phenomena Hazard Program. Probabilistic hazard models are available for earthquake, extreme wind/tornado, and flood. Alternatively, site organizations are encouraged to develop site-specific hazard models utilizing the most recent information and techniques available. In this document, performance goals and natural hazard levels are expressed in probabilistic terms, and design and evaluation procedures are presented in deterministic terms. Design/evaluation procedures conform closely to common standard practices so that the procedures will be easily understood by most engineers. Performance goals are expressed in terms of structure or equipment damage to the extent that: (1) the facility cannot function; (2) the facility would need to be replaced; or (3) personnel are endangered. 82 refs., 12 figs., 18 tabs

Design and evaluation guidelines for Department of Energy facilities subjected to natural phenomena hazards

Energy Technology Data Exchange (ETDEWEB)

Kennedy, R.P. (Structural Mechanics Consulting, Inc., Yorba Linda, CA (USA)); Short, S.A. (ABB Impell Corp., Mission Viejo, CA (USA)); McDonald, J.R. (Texas Tech Univ., Lubbock, TX (USA)); McCann, M.W. Jr. (Benjamin (J.R.) and Associates, Inc., Mountain View, CA (USA)); Murray, R.C. (Lawrence Livermore National Lab., CA (USA)); Hill, J.R. (USDOE Assistant Secretary for Environment, Safety, and He

1990-06-01

The Department of Energy (DOE) and the DOE Natural Phenomena Hazards Panel have developed uniform design and evaluation guidelines for protection against natural phenomena hazards at DOE sites throughout the United States. The goal of the guidelines is to assure that DOE facilities can withstand the effects of natural phenomena such as earthquakes, extreme winds, tornadoes, and flooding. The guidelines apply to both new facilities (design) and existing facilities (evaluation, modification, and upgrading). The intended audience is primarily the civil/structural or mechanical engineers conducting the design or evaluation of DOE facilities. The likelihood of occurrence of natural phenomena hazards at each DOE site has been evaluated by the DOE Natural Phenomena Hazard Program. Probabilistic hazard models are available for earthquake, extreme wind/tornado, and flood. Alternatively, site organizations are encouraged to develop site-specific hazard models utilizing the most recent information and techniques available. In this document, performance goals and natural hazard levels are expressed in probabilistic terms, and design and evaluation procedures are presented in deterministic terms. Design/evaluation procedures conform closely to common standard practices so that the procedures will be easily understood by most engineers. Performance goals are expressed in terms of structure or equipment damage to the extent that: (1) the facility cannot function; (2) the facility would need to be replaced; or (3) personnel are endangered. 82 refs., 12 figs., 18 tabs.

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1993-01-01

The document reproduces the Note Verbale dated 2 December 1992 received by the Director General from the Resident Representative of Argentina to the Agency relating to the export of nuclear material, equipment or technology, in order to provide information on that Government's Guidelines for Transfers of Nuclear-related Dual-use Equipment, Material and related Technology

Physical Activity Design Guidelines for School Architecture.

Science.gov (United States)

Brittin, Jeri; Sorensen, Dina; Trowbridge, Matthew; Lee, Karen K; Breithecker, Dieter; Frerichs, Leah; Huang, Terry

2015-01-01

Increasing children's physical activity at school is a national focus in the U.S. to address childhood obesity. While research has demonstrated associations between aspects of school environments and students' physical activity, the literature currently lacks a synthesis of evidence to serve as a practical, spatially-organized resource for school designers and decision-makers, as well as to point to pertinent research opportunities. This paper describes the development of a new practical tool: Physical Activity Design Guidelines for School Architecture. Its aims are to provide architects and designers, as well as school planners, educators, and public health professionals, with strategies for making K-12 school environments conducive to healthy physical activity, and to engage scientists in transdisciplinary perspectives toward improved knowledge of the school environment's impact. We used a qualitative review process to develop evidence-based and theory-driven school design guidelines that promote increased physical activity among students. The design guidelines include specific strategies in 10 school design domains. Implementation of the guidelines is expected to enable students to adopt healthier physical activity behaviors. The tool bridges a translational gap between research and environmental design practice, and may contribute to setting new industry and education standards.

Integrated Human Factors Design Guidelines for Sound Interface

International Nuclear Information System (INIS)

Lee, Jung Woon; Lee, Yong Hee; Oh, In Seok; Lee, Hyun Chul; Cha, Woo Chang

2004-05-01

Digital MMI, such as CRT, LCD etc., has been used increasingly in the design of main control room of the Korean standard nuclear power plants following the YGN units 3 and 4. The utilization of digital MMI may introduce various kind of sound interface into the control room design. In this project, for five top-level guideline items, including Sound Formats, Alarms, Sound Controls, Communications, and Environments, a total of 147 detail guidelines were developed and a database system for these guidelines was developed. The integrated human factors design guidelines for sound interface and the database system developed in this project will be useful for the design of sound interface of digital MMI in Korean NPPs

Integrated Human Factors Design Guidelines for Sound Interface

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Lee, Yong Hee; Oh, In Seok; Lee, Hyun Chul [KAERI, Daejeon (Korea, Republic of); Cha, Woo Chang [Kumoh National Univ. of Technology, Gumi (Korea, Republic of)

2004-05-15

Digital MMI, such as CRT, LCD etc., has been used increasingly in the design of main control room of the Korean standard nuclear power plants following the YGN units 3 and 4. The utilization of digital MMI may introduce various kind of sound interface into the control room design. In this project, for five top-level guideline items, including Sound Formats, Alarms, Sound Controls, Communications, and Environments, a total of 147 detail guidelines were developed and a database system for these guidelines was developed. The integrated human factors design guidelines for sound interface and the database system developed in this project will be useful for the design of sound interface of digital MMI in Korean NPPs.

Guidelines for equipment and staffing of radiotherapy facilities in the European countries: Final results of the ESTRO-HERO survey

DEFF Research Database (Denmark)

Dunscombe, Peter; Grau, Cai; Defourny, Noémie

2014-01-01

of guidelines for equipment and staffing and selected operational issues. Twenty-nine countries provided full or partial evaluable responses. RESULTS: The availability of guidelines across Europe is far from uniform. The metrics used for capital and human resources are variable. There seem to have been no major...... guidelines suggesting developments in clinical radiotherapy are moving faster than guideline updating. CONCLUSION: The efficient provision of safe, high quality radiotherapy services would benefit from the availability of well-structured guidelines for capital and human resources, based on agreed upon...

Physical Activity Design Guidelines for School Architecture.

Directory of Open Access Journals (Sweden)

Jeri Brittin

Full Text Available Increasing children's physical activity at school is a national focus in the U.S. to address childhood obesity. While research has demonstrated associations between aspects of school environments and students' physical activity, the literature currently lacks a synthesis of evidence to serve as a practical, spatially-organized resource for school designers and decision-makers, as well as to point to pertinent research opportunities. This paper describes the development of a new practical tool: Physical Activity Design Guidelines for School Architecture. Its aims are to provide architects and designers, as well as school planners, educators, and public health professionals, with strategies for making K-12 school environments conducive to healthy physical activity, and to engage scientists in transdisciplinary perspectives toward improved knowledge of the school environment's impact. We used a qualitative review process to develop evidence-based and theory-driven school design guidelines that promote increased physical activity among students. The design guidelines include specific strategies in 10 school design domains. Implementation of the guidelines is expected to enable students to adopt healthier physical activity behaviors. The tool bridges a translational gap between research and environmental design practice, and may contribute to setting new industry and education standards.

Communication Received from the Permanent Mission of the Republic of Serbia to the International Atomic Energy Agency Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology and the Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology

International Nuclear Information System (INIS)

2012-01-01

The Director General has received a note verbale dated 28 September 2012 from the Permanent Mission of Serbia to the International Atomic Energy Agency providing information on the decision of the Government of Serbia to adhere to the 'Guidelines for the Export of Nuclear Material, Equipment and Technology', issued as document INFCIRC/254/Rev.10/Part 1, including its Annexes, and with the 'Guidelines for Transfers of Nuclear-Related Dual-Use Equipment, Material, Software and Related Technology', issued as document INFCIRC/254/Rev.8/Part 2 [es

Communication Received from the Permanent Mission of the Republic of Serbia to the International Atomic Energy Agency Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology and the Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology

International Nuclear Information System (INIS)

2012-01-01

The Director General has received a note verbale dated 28 September 2012 from the Permanent Mission of Serbia to the International Atomic Energy Agency providing information on the decision of the Government of Serbia to adhere to the 'Guidelines for the Export of Nuclear Material, Equipment and Technology', issued as document INFCIRC/254/Rev.10/Part 1, including its Annexes, and with the 'Guidelines for Transfers of Nuclear-Related Dual-Use Equipment, Material, Software and Related Technology', issued as document INFCIRC/254/Rev.8/Part 2 [fr

Communication Received from the Permanent Mission of the Republic of Serbia to the International Atomic Energy Agency Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology and the Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology

International Nuclear Information System (INIS)

2012-01-01

The Director General has received a note verbale dated 28 September 2012 from the Permanent Mission of Serbia to the International Atomic Energy Agency providing information on the decision of the Government of Serbia to adhere to the 'Guidelines for the Export of Nuclear Material, Equipment and Technology', issued as document INFCIRC/254/Rev.10/Part 1, including its Annexes, and with the 'Guidelines for Transfers of Nuclear-Related Dual-Use Equipment, Material, Software and Related Technology', issued as document INFCIRC/254/Rev.8/Part 2

The design of management system guidelines and technical standards for the production of x-ray aircraft

International Nuclear Information System (INIS)

Dyah Palupi; Made Pramayuni

2013-01-01

Concept of management systems guidelines and technical standards X-ray Equipment Production arranged in order to prepare for the effective and efficient regulatory to ensure the safety of X-ray equipment production in Indonesia. The regulatory tools may the government policy or regulations. Authors proposed that BAPETEN develop guidelines for management system of x-ray equipment production by combining ISO 13485 with BAPETEN Chairman Regulation no.4 /2010. Author also suggested that BAPETEN make technical standards IEC 60601 as a mandatory standard in producing x-ray equipment. (author)

Advanced human-system interface design review guidelines

International Nuclear Information System (INIS)

O'Hara, J.M.

1990-01-01

Advanced, computer-based, human-system interface designs are emerging in nuclear power plant (NPP) control rooms. These developments may have significant implications for plant safety in that they will greatly affect the ways in which operators interact with systems. At present, however, the only guidance available to the US Nuclear Regulatory Commission (NRC) for the review of control room-operator interfaces, NUREG-0700, was written prior to these technological changes and is thus not designed to address them. The objective of the project reported in this paper is to develop an Advanced Control Room Design Review Guideline for use in performing human factors reviews of advanced operator interfaces. This guideline will be implemented, in part, as a portable, computer-based, interactive document for field use. The paper describes the overall guideline development methodology, the present status of the document, and the plans for further guideline testing and development. 21 refs., 3 figs

Maintenance program guidelines for programmatic equipment

International Nuclear Information System (INIS)

1994-11-01

The Division Directors at Lawrence Berkeley Laboratory are responsible for implementing a maintenance program for research equipment (also referred to as programmatic equipment) assigned to them. The program must allow maintenance to be accomplished in a manner that promotes operational safety, environmental protection and compliance, and cost effectiveness; that preserves the intended functions of the facilities and equipment; and that supports the programmatic mission of the Laboratory. Programmatic equipment -- such as accelerators, lasers, radiation detection equipment, and glove boxes -- is dedicated specifically to research. Installed equipment, by contrast, includes the mechanical and electrical systems installed as part of basic building construction, equipment essential to the normal functioning of the facility and its intended use. Examples of installed equipment are heating, ventilating, and air conditioning systems; elevators; and communications systems. The LBL Operating and Assurance Program Plan (PUB-3111, Revision 4) requires that a maintenance program be prepared for programmatic equipment and defines the basic maintenance program elements. Such a program of regular, documented maintenance is vital to the safety and quality of research activities. As a part of that support, this document offers guidance to Laboratory organizations for developing their maintenance programs. It clarifies the maintenance requirements of the Operating and Assurance Program (OAP) and presents an approach that, while not the only possibility, can be expected to produce an effective maintenance program for research equipment belonging to the Laboratory's organizations

Equipment and special tool design for remote maintenance

International Nuclear Information System (INIS)

Northey, L.M.; Thomson, J.D.

1985-01-01

Maintenance tasks performed in locations with hostile environments and/or limited space accesses often require equipment that is operated remotely. This paper discusses considerations that should be addressed in the design of remote maintenance equipment. Some of the topics include proper material selection, interface identifications, operational feedback devices and cost limitations. These considerations add ''human engineering'' to the equipment design to assure protection of the tool and the operating personnel. Examples of remote maintenance and inspection systems that were developed by the Westinghouse Hanford Company and that utilize many of these design considerations are included

Nuclear power plant equipment design and construction rules

International Nuclear Information System (INIS)

Boiron, P.

1983-03-01

Presentation of the AFCEN (French association for nuclear power plant equipment design and construction rules) working, of its edition activity and of somes of its edited documents such as RCC-C (design and construction rules for PWR power plant fuel assemblies) and RCC-E (design and construction rules for nuclear facility electrical equipments) [fr

ITER L 7 duct remote handling equipment design report

International Nuclear Information System (INIS)

Millard, J.

1996-09-01

The operation, design and interfaces of the 'Duct Vehicle' and it's associated remote handling equipment are briefly described in this document. This equipment is being designed by Spar Aerospace Ltd. for the Divertor Test Platform as part of ITER Research and Development Project L-7. Canadian Fusion Fuels Technology Project funds this work as part of the Canadian Contribution to ITER. This document describes the equipment design status at the September 1996 design review. 23 figs

Design of experimental equipment at CRNL

International Nuclear Information System (INIS)

Godden, B.

1976-01-01

The Plant Design Division provides a design service to the research and development effort at CRNL. Severe constraints, both environmentally and spatially, are placed on the design of special equipment. Several examples are given. Finally, the use of automated drafting systems is described. (author)

Verification of the thermal design of electronic equipment

Energy Technology Data Exchange (ETDEWEB)

Hienonen, R.; Karjalainen, M.; Lankinen, R. [VTT Automation, Espoo (Finland). ProTechno

1997-12-31

The project `Verification of the thermal design of electronic equipment` studied the methodology to be followed in the verification of thermal design of electronic equipment. This project forms part of the `Cool Electronics` research programme funded by TEKES, the Finnish Technology Development Centre. This project was carried out jointly by VTT Automation, Lappeenranta University of Technology, Nokia Research Center and ABB Industry Oy VSD-Technology. The thermal design of electronic equipment has a significant impact on the cost, reliability, tolerance to different environments, selection of components and materials, and ergonomics of the product. This report describes the method for verification of thermal design. It assesses the goals set for thermal design, environmental requirements, technical implementation of the design, thermal simulation and modelling, and design qualification testing and the measurements needed. The verification method covers all packaging levels of electronic equipment from the system level to the electronic component level. The method described in this report can be used as part of the quality system of a corporation. The report includes information about the measurement and test methods needed in the verification process. Some measurement methods for the temperature, flow and pressure of air are described. (orig.) Published in Finnish VTT Julkaisuja 824. 22 refs.

Electrical equipment design library

International Nuclear Information System (INIS)

1994-01-01

This book guides the design supervision, construction order for electrical equipment. The contents of this library are let's use electricity like this, leading-in-pole and casual power, electric pole install below 300KVA, electric pole install below 301∼1000KVA, electric pole install exceed 1000KVA, rooftop install exceed 1000KVA, CUBICLE type, 154KV services. It adds an appendix.

Generic testability and test methods guidelines for ASIC devices

International Nuclear Information System (INIS)

Puri, K.; Takeda, H.

1996-04-01

Many industries are switching from analog equipment to digital equipment. This change has become desirable because digital devices have become cost-effective, easily available, highly reliable, easy to qualify and easy to test and replace when needed. The nuclear power industry is beginning to upgrade some of its instrumentation and control equipment from an analog design to digital design. A digital application specific integrated circuit (ASIC) device can be designed to perform the same functions as performed by analog modules. However, the ASIC must be designed for cost-effective testability and qualification. This report provides generic guidelines for designing cost-effective methods for testing and characterizing ASIC devices to accomplish qualification

Engineering design guidelines for nuclear criticality safety

International Nuclear Information System (INIS)

Waltz, W.R.

1988-08-01

This document provides general engineering design guidelines specific to nuclear criticality safety for a facility where the potential for a criticality accident exists. The guide is applicable to the design of new SRP/SRL facilities and to major modifications Of existing facilities. The document is intended an: A guide for persons actively engaged in the design process. A resource document for persons charged with design review for adequacy relative to criticality safety. A resource document for facility operating personnel. The guide defines six basic criticality safety design objectives and provides information to assist in accomplishing each objective. The guide in intended to supplement the design requirements relating to criticality safety contained in applicable Department of Energy (DOE) documents. The scope of the guide is limited to engineering design guidelines associated with criticality safety and does not include other areas of the design process, such as: criticality safety analytical methods and modeling, nor requirements for control of the design process

Design guidelines for mini-roundabouts

CSIR Research Space (South Africa)

Emslie, I

1997-03-01

Full Text Available Guidelines for Traffic Calming. Concepts and principles relating to the use of mini-roundabouts as a form of intersection control and in the traffic calming context are discussed. Warrants for the implementation of mini-roundabouts and design standards...

Seismic qualification of non-safety class equipment whose failure would damage safety class equipment

International Nuclear Information System (INIS)

LaSalle, F.R.

1991-01-01

Both Code of Federal Regulations, Title 10, Part 50, and US Department of Energy Order 6340.1A have requirements to assess the interaction of non-safety and safety class structures and equipment during a seismic event to maintain the safety function. At the Hanford Site, a cost effective program has been developed to perform the evaluation of non-safety class equipment. Seismic qualification is performed by analysis, test, or upgrading of the equipment to ensure the integrity of safety class structures and equipment. This paper gives a brief overview and synopsis that address design analysis guidelines including applied loading, damping values, component anchorage, allowable loads, and stresses. Test qualification of equipment and walkdown acceptance criteria for heating ampersand ventilation (H ampersand V) ducting, conduit, cable tray, missile zone of influence, as well as energy criteria are presented

Healthy eating design guidelines for school architecture.

Science.gov (United States)

Huang, Terry T-K; Sorensen, Dina; Davis, Steven; Frerichs, Leah; Brittin, Jeri; Celentano, Joseph; Callahan, Kelly; Trowbridge, Matthew J

2013-01-01

We developed a new tool, Healthy Eating Design Guidelines for School Architecture, to provide practitioners in architecture and public health with a practical set of spatially organized and theory-based strategies for making school environments more conducive to learning about and practicing healthy eating by optimizing physical resources and learning spaces. The design guidelines, developed through multidisciplinary collaboration, cover 10 domains of the school food environment (eg, cafeteria, kitchen, garden) and 5 core healthy eating design principles. A school redesign project in Dillwyn, Virginia, used the tool to improve the schools' ability to adopt a healthy nutrition curriculum and promote healthy eating. The new tool, now in a pilot version, is expected to evolve as its components are tested and evaluated through public health and design research.

Structural design of nuclear reactor machinery and equipment

International Nuclear Information System (INIS)

Hara, Hideki

1992-01-01

Since the machinery, equipment and piping which compose nuclear power station facilities are diverse, when those are designed, consideration is given sufficiently to the objective of use and the importance of the object machinery and equipment so that those can maintain the soundness over the design life. In this report, on the contents and the design standard in the design techniques for nuclear reactor machinery and equipment, the way of thinking is shown, taking an example of reactor pressure vessel which is stipulated as the vessel kind 1 in the 'Technical standard of structures and others regarding nuclear facilities for electric power generation', Notice No. 501 of the Ministry of International Trade and Industry. The reactor pressure vessel of 1350 MWe improved type BWR (ABWR) is used under the condition of 87.9 kg/cm 2 and 302 degC, and the inside diameter is about 7.2 m, the inside height is about 21 m, and the wall thickness is about 170 mm. The design standard for reactor pressure vessels and its way of thinking, breakdown prevention design and the design techniques for reactor pressure vessels are described. (K.I.)

Guidelines for preparing IAEA design information questionnaires

International Nuclear Information System (INIS)

Swartz, J.M.; Bieber, A.M.

1980-01-01

The format of the IAEA Design Information Questionnaires and the SAI prepared guidelines for completing them, is described. The guidelines should assist facility operators in meeting the time constraints set forth in the Subsidiary Arrangements by effectively supplying the information needed by the IAEA and in minimizing resource allocations to the preparation effort. 8 refs

Liquid Metal Fast Breeder Reactor plant maintenance and equipment design

International Nuclear Information System (INIS)

Swannack, D.L.

1982-01-01

This paper provides a summary of maintenance equipment considerations and actual plant handling experiences from operation of a sodium-cooled reactor, the Fast Flux Test Facility (FFTF). Equipment areas relating to design, repair techniques, in-cell handling, logistics and facility services are discussed. Plant design must make provisions for handling and replacement of components within containment or allow for transport to an ex-containment area for repair. The modular cask assemblies and transporter systems developed for FFTF can service major plant components as well as smaller units. The plant and equipment designs for the Clinch River Breeder Reactor (CRBR) plant have been patterned after successful FFTF equipment

Vitrification process equipment design for the West Valley Demonstration Project

International Nuclear Information System (INIS)

Chapman, C.C.; Drosjack, W.P.

1988-10-01

The vitrification process and equipment design is nearing completion for the West Valley Project. This report provides the basis and current status for the design of the major vessels and equipment within the West Valley Vitrification Plant. A review of the function and key design features of the equipment is also provided. The major subsystems described include the feed preparation and delivery systems, the melter, the canister handling systems, and the process off-gas system. 11 refs., 33 figs., 4 tabs

Maintainability design criteria for packaging of spacecraft replaceable electronic equipment.

Science.gov (United States)

Kappler, J. R.; Folsom, A. B.

1972-01-01

Maintainability must be designed into long-duration spacecraft and equipment to provide the required high probability of mission success with the least cost and weight. The ability to perform repairs quickly and easily in a space environment can be achieved by imposing specific maintainability design criteria on spacecraft equipment design and installation. A study was funded to investigate and define design criteria for electronic equipment that would permit rapid removal and replacement in a space environment. The results of the study are discussed together with subsequent simulated zero-g demonstration tests of a mockup with new concepts for packaging.

Communications received from certain member states regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1993-04-01

The document reproduces the Note Verbale dated 8 February 1993 received by the Director General from the Permanent Mission of the Russian Federation to the International Organizations in Vienna, relating to the export of nuclear material, equipment or technology, in order to provide information on that Government's Guidelines for Nuclear Transfer

Advanced control room design review guidelines: Integration of the NUREG-0700 guidelines and development of new human-system interface guidelines

Energy Technology Data Exchange (ETDEWEB)

Carter, R.J.

1997-07-01

This report documents the work conducted in four tasks of the Nuclear Regulatory Commission (NRC) project entitled Review Criteria for Human Factors Aspects of Advanced Controls and Instrumentation. The purpose of the first task was to integrate the applicable sections of NUREG-0700 into the advanced control room design review (ACRDR) guidelines to ensure that all applicable guidelines are together in one document and conveniently accessible to users. The primary objective of the second task was to formulate a strategy for the development of new ACRDR guidelines that have not otherwise been identified. The main focus of the third task was to modify the individual ACRDR guidelines generated to date to ensure that they are suitable for the intended nuclear power plant (NPP) control station system application. The goal of the fourth task was to develop human factors guidelines for two human-system interface categories that are missing from the current ACRDR guidelines document. During the first task those areas in NUREG-0700 that are not addressed by the ACRDR guidelines document were identified, the areas were subsequently reviewed against six recent industry human factors engineering review guidelines, and the NUREG-0700 guidelines were updated as necessary. In the second task 13 general categories of human-system interface guidelines that are either missing from or not adequately addressed by the ACRDR document were discovered. An approach was derived for the development of new ACRDR guidelines, a preliminary assessment of the available sources that may be useful in the creation of new guidelines and their applicability to the identified human-system interface categories was performed, and an estimate was made of the amount of time and level of effort required to complete the development of needed new ACRDR guidelines. During the third task those NPP control station systems to which the NUREG-0700 and ACRDR guidelines apply were identified, matrices of such

Advanced control room design review guidelines: Integration of the NUREG-0700 guidelines and development of new human-system interface guidelines

International Nuclear Information System (INIS)

Carter, R.J.

1997-07-01

This report documents the work conducted in four tasks of the Nuclear Regulatory Commission (NRC) project entitled Review Criteria for Human Factors Aspects of Advanced Controls and Instrumentation. The purpose of the first task was to integrate the applicable sections of NUREG-0700 into the advanced control room design review (ACRDR) guidelines to ensure that all applicable guidelines are together in one document and conveniently accessible to users. The primary objective of the second task was to formulate a strategy for the development of new ACRDR guidelines that have not otherwise been identified. The main focus of the third task was to modify the individual ACRDR guidelines generated to date to ensure that they are suitable for the intended nuclear power plant (NPP) control station system application. The goal of the fourth task was to develop human factors guidelines for two human-system interface categories that are missing from the current ACRDR guidelines document. During the first task those areas in NUREG-0700 that are not addressed by the ACRDR guidelines document were identified, the areas were subsequently reviewed against six recent industry human factors engineering review guidelines, and the NUREG-0700 guidelines were updated as necessary. In the second task 13 general categories of human-system interface guidelines that are either missing from or not adequately addressed by the ACRDR document were discovered. An approach was derived for the development of new ACRDR guidelines, a preliminary assessment of the available sources that may be useful in the creation of new guidelines and their applicability to the identified human-system interface categories was performed, and an estimate was made of the amount of time and level of effort required to complete the development of needed new ACRDR guidelines. During the third task those NPP control station systems to which the NUREG-0700 and ACRDR guidelines apply were identified, matrices of such

A Perspective on Equipment Design for Fusion Remote Handling

International Nuclear Information System (INIS)

Mills, S.; Haist, B.; Hamilton, D.

2006-01-01

For 8 years, JET remote operations have become more capable and confident. Many tasks have been successfully completed, even those never intended to be remote maintenance activities. The general approach to the provision of remote handling equipment at JET has been the preferred use of commercially-off-the-shelf equipment. In the areas of electrical, electronic, software and control this approach has been generally achievable. However, in the area of mechanical equipment it has been more difficult. In particular the RH tooling has been almost entirely bespoke as its requirements are highly sensitive to the design of the JET component being handled and there are many design variations. Hence, JET has required the design and manufacture of over 700 types of bespoke RH equipment. This paper will discuss the experience of introducing and developing remote handling mechanical equipment for JET. The paper will cover the relationship between the remote handling equipment and the JET component design and the potential for improving the design function. A major lesson from the introduction of remote handling to JET has been demonstration of the very close interdependency of the design of JET components with design of remote handling tooling. The JET remote handling manual was originally introduced as the vehicle to ensure remote handling compatibility by the introduction of standards. Experience has shown that in general the remote handling manual approach has been insufficient. Future fusion machines will be much more complex than JET and will demand even greater remote handling compatibility. This paper will discuss possible methods for improving this process. Equipment operating in a high radiation environment must be dependable It may spend part of its time in areas that would be extremely difficult to recover from in the case of failure. The equipment may also have a high duty cycle to minimise shutdown times and probably cannot be manually inspected on a frequent

Seismic isolation design guidelines for KALIMER(Revision A)

International Nuclear Information System (INIS)

Yoo, B; Koo, Gyeong Hoi; Lee, J. H.

2000-04-01

The main purpose of this report is to develop the seismic isolation design guideline for KALIMER(Korea Advanced LIquid MEtal Reactor). The proposed design rules(revision A) are only applicable to the seismic isolation design with using the high damping laminated rubber bearings. When using other seismic isolation devices and applying to 3-dimensional isolation, the proposed guidelines shall be modified and added with proper research data. The rules described in this report are based on the research results performed up to now but needed to be upgraded and verified with more detail research works for the future

Communications received from certain member states regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1993-04-01

The document reproduces the text of a Note Verbale dated 5 March 1993 received by the Director General from the Ministry of Foreign Affairs of the Slovak Republic, in order to provide information on that Government's Guidelines for Nuclear Transfer and for Transfers of Nuclear - Related Dual-Use Equipment, Material and Related Technology

Development of guidelines for inelastic analysis in design of fast reactor components

International Nuclear Information System (INIS)

Nakamura, Kyotada; Kasahara, Naoto; Morishita, Masaki; Shibamoto, Hiroshi; Inoue, Kazuhiko; Nakayama, Yasunari

2008-01-01

The interim guidelines for the application of inelastic analysis to design of fast reactor components were developed. These guidelines are referred from 'Elevated Temperature Structural Design Guide for Commercialized Fast Reactor (FDS)'. The basic policies of the guidelines are more rational predictions compared with elastic analysis approach and a guarantee of conservative results for design conditions. The guidelines recommend two kinds of constitutive equations to estimate strains conservatively. They also provide the methods for modeling load histories and estimating fatigue and creep damage based on the results of inelastic analysis. The guidelines were applied to typical design examples and their results were summarized as exemplars to support users

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1993-01-01

The document reproduces the Note Verbale dated 2 December 1992 received by the Director General from the Resident Representative of Argentina to the Agency relating to the export of nuclear material, equipment and technology in order to clarify parts of the Trigger List which is incorporated in Annex A to the Guidelines for Nuclear Transfers

Human-system interface design review guideline -- Process and guidelines: Final report. Revision 1, Volume 1

International Nuclear Information System (INIS)

1996-06-01

NUREG-0700, Revision 1, provides human factors engineering (HFE) guidance to the US Nuclear Regulatory Commission staff for its: (1) review of the human system interface (HSI) design submittals prepared by licensees or applications for a license or design certification of commercial nuclear power plants, and (2) performance of HSI reviews that could be undertaken as part of an inspection or other type of regulatory review involving HSI design or incidents involving human performance. The guidance consists of a review process and HFE guidelines. The document describes those aspects of the HSI design review process that are important to the identification and resolution of human engineering discrepancies that could adversely affect plant safety. Guidance is provided that could be used by the staff to review an applicant's HSI design review process or to guide the development of an HSI design review plan, e.g., as part of an inspection activity. The document also provides detailed HFE guidelines for the assessment of HSI design implementations. NUREG-0700, Revision 1, consists of three stand-alone volumes. Volume 1 consists of two major parts. Part 1 describes those aspects of the review process of the HSI design that are important to identifying and resolving human engineering discrepancies. Part 2 contains detailed guidelines for a human factors engineering review which identify criteria for assessing the implementation of an applicant's or licensee's HSI design

Equipment Obsolescence Management Program

Energy Technology Data Exchange (ETDEWEB)

Redmond, J.

2014-07-01

Nuclear Power Plant (NPP) Operators are challenged with securing reliable supply channels for safety related equipment due to equipment obsolescence. Many Original Equipment Manufacturers (OEMs) have terminated production of spare parts and product life-cycle support. The average component life cycles are much shorter than the NPP design life, which means that replacement components and parts for the original NPP systems are not available for the complete design life of the NPPs. The lack or scarcity of replacement parts adversely affects plant reliability and ultimately the profitability of the affected NPPs. This problem is further compounded when NPPs pursue license renewal and approval for plant-life extension. A reliable and predictable supply of replacement co components is necessary for NPPs to remain economically competitive and meet regulatory requirements and guidelines. Electrical and I and C components, in particular, have short product life cycles and obsolescence issues must be managed pro actively and not reactively in order to mitigate the risk to the NPP to ensure reliable and economic NPP operation. (Author)

A study on design guidelines for the icons used in nuclear power plants

International Nuclear Information System (INIS)

Lee, Jung Woon; Lee, Yong Hee; Oh, In Seok; Lee, Hyun Chul; Lee, Dhong Ha

2004-05-01

In this project, advantages and disadvantages of icons on electronic displays were analyzed, and design procedures, design evaluation principles, and design guidelines for icons on electronic displays were developed. In addition, as design guidelines for special effects applicable to icons on electronic displays, guidelines for color coding, flashing, and 3-dimensional effects were developed. A questionnaire survey was performed to investigate how NPP operators consider methods representing icons on electronic displays (such as colors, dynamic effects, and 3-dimensional effects) compared to methods representing icons by using outlines in the P and ID drawings. NPP operators' preference of the icons designed in accordance with icon design guidelines to the icons without considering the guidelines was also investigated

Development of human factors design review guidelines

International Nuclear Information System (INIS)

Lee, Jung Woon; Oh, In Suk; Suh, Sang Moon; Lee, Hyun Chul

1997-10-01

The Objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: '25, Human factors engineering program review model' and '26, Review criteria for human actors aspects of advanced controls and instrumentation', which are related to the development of human factors safety regulation guides be ing performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and reviewing the reference documents of NUREG-0711. We also computerized the Korean version of NUREG-0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm systems. Then we well update the guidelines by reviewing the literature related to alarm design published after 1994

Development of human factors design review guidelines

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Oh, In Suk; Suh, Sang Moon; Lee, Hyun Chul [Korea Atomic Energy Research Institute, Taejon (Korea)

1997-10-01

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: 25. Human Factors Engineering Program Review Model and 26. Review Criteria for Human Factors Aspects of Advanced Controls and Instrumentation, which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and reviewing the reference documents of NUREG-0711. We also computerized the Korean version of NUREG-0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm systems. Then we will update the guidelines by reviewing the literature related to alarm design published after 1994. (author). 12 refs., 5 figs., 2 tabs.

Energy Design Guidelines for High Performance Schools: Tropical Island Climates

Energy Technology Data Exchange (ETDEWEB)

2004-11-01

The Energy Design Guidelines for High Performance Schools--Tropical Island Climates provides school boards, administrators, and design staff with guidance to help them make informed decisions about energy and environmental issues important to school systems and communities. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school in tropical island climates. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs.

Screen Design Guidelines for Motivation in Interactive Multimedia Instruction: A Survey and Framework for Designers.

Science.gov (United States)

Lee, Sung Heum; Boling, Elizabeth

1999-01-01

Identifies guidelines from the literature relating to screen design and design of interactive instructional materials. Describes two types of guidelines--those aimed at enhancing motivation and those aimed at preventing loss of motivation--for typography, graphics, color, and animation and audio. Proposes a framework for considering motivation in…

Human-system interface design review guideline -- Process and guidelines: Final report. Revision 1, Volume 1

Energy Technology Data Exchange (ETDEWEB)

None

1996-06-01

NUREG-0700, Revision 1, provides human factors engineering (HFE) guidance to the US Nuclear Regulatory Commission staff for its: (1) review of the human system interface (HSI) design submittals prepared by licensees or applications for a license or design certification of commercial nuclear power plants, and (2) performance of HSI reviews that could be undertaken as part of an inspection or other type of regulatory review involving HSI design or incidents involving human performance. The guidance consists of a review process and HFE guidelines. The document describes those aspects of the HSI design review process that are important to the identification and resolution of human engineering discrepancies that could adversely affect plant safety. Guidance is provided that could be used by the staff to review an applicant`s HSI design review process or to guide the development of an HSI design review plan, e.g., as part of an inspection activity. The document also provides detailed HFE guidelines for the assessment of HSI design implementations. NUREG-0700, Revision 1, consists of three stand-alone volumes. Volume 1 consists of two major parts. Part 1 describes those aspects of the review process of the HSI design that are important to identifying and resolving human engineering discrepancies. Part 2 contains detailed guidelines for a human factors engineering review which identify criteria for assessing the implementation of an applicant`s or licensee`s HSI design.

Design Guidelines for New Generation Network Architecture

Science.gov (United States)

Harai, Hiroaki; Fujikawa, Kenji; Kafle, Ved P.; Miyazawa, Takaya; Murata, Masayuki; Ohnishi, Masaaki; Ohta, Masataka; Umezawa, Takeshi

Limitations are found in the recent Internet because a lot of functions and protocols are patched to the original suite of layered protocols without considering global optimization. This reveals that end-to-end argument in the original Internet was neither sufficient for the current societal network and nor for a sustainable network of the future. In this position paper, we present design guidelines for a future network, which we call the New Generation Network, which provides the inclusion of diverse human requirements, reliable connection between the real-world and virtual network space, and promotion of social potentiality for human emergence. The guidelines consist of the crystal synthesis, the reality connection, and the sustainable & evolutional guidelines.

Design guide for heat transfer equipment in water-cooled nuclear reactor systems

International Nuclear Information System (INIS)

1975-07-01

Information pertaining to design methods, material selection, fabrication, quality assurance, and performance tests for heat transfer equipment in water-cooled nuclear reactor systems is given in this design guide. This information is intended to assist those concerned with the design, specification, and evaluation of heat transfer equipment for nuclear service and the systems in which this equipment is required. (U.S.)

Design of EPON far-end equipment based on FTTH

Science.gov (United States)

Feng, Xiancheng; Yun, Xiang

2008-12-01

Now, most favors fiber access is mainly the EPON fiber access system. Inheriting from the low cost of Ethernet, usability and bandwidth of optical network, EPON technology is one of the best technologies in fiber access and is adopted by the carriers all over the world widely. According to the scheme analysis to FTTH fan-end equipment, hardware design of ONU is proposed in this paper. The FTTH far-end equipment software design deference modulation design concept, it divides the software designment into 5 function modules: the module of low-layer driver, the module of system management, the module of master/slave communication, and the module of main/Standby switch and the module of command line. The software flow of the host computer is also analyzed. Finally, test is made for Ethernet service performance of FTTH far-end equipment, E1 service performance and the optical path protection switching, and so on. The results of test indicates that all the items are accordance with technical request of far-end ONU equipment and possess good quality and fully reach the requirement of telecommunication level equipment. The far-end equipment of FTTH divides into several parts based on the function: the control module, the exchange module, the UNI interface module, the ONU module, the EPON interface module, the network management debugging module, the voice processing module, the circuit simulation module, the CATV module. In the downstream direction, under the protect condition, we design 2 optical modules. The system can set one group optical module working and another group optical module closure when it is initialized. When the optical fiber line is cut off, the LOS warning comes out. It will cause MUX to replace another group optical module, simultaneously will reset module 3701/3711 and will make it again test the distance, and will give the plug board MPC850 report through the GPIO port. During normal mode, the downstream optical signal is transformed into the

A preliminary design of mechanical device on industrial digital radiography equipment design

International Nuclear Information System (INIS)

Nur Khasan; Samuel Praptoyo

2015-01-01

A preliminary design of mechanical device on industrial digital radiography equipment has been done. this design is intended as a basis for the manufacture of complete facilities for the realization a prototype on industrial digital radiography equipment. the design and construction were carried out by paying attention to the general configuration of the basic design in which its mechanical design has several components with specific dimensions and heavy mass. this design consist of a main frame holder, flat panel detector support and hydraulic hand stacker for mounting the x-ray machine. this mechanical device design will then be fabricated to facilitate and assist work of digital radiographic retrieval. computer application programs sketch-up is used to draw this design and the analysis stress of autodesk inventor to analysis the strength construction design. the results of this design are the configuration drawing, sketch drawings of construction and the safety factor of construction design with a minimum value of 2.39 as well as a maximum value of 15 when to be simulated by the load 500 Kg which is 4 times of total workload. (author)

Standard guide for hot cell specialized support equipment and tools

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 Intent: 1.1.1 This guide presents practices and guidelines for the design and implementation of equipment and tools to assist assembly, disassembly, alignment, fastening, maintenance, or general handling of equipment in a hot cell. Operating in a remote hot cell environment significantly increases the difficulty and time required to perform a task compared to completing a similar task directly by hand. Successful specialized support equipment and tools minimize the required effort, reduce risks, and increase operating efficiencies. 1.2 Applicability: 1.2.1 This guide may apply to the design of specialized support equipment and tools anywhere it is remotely operated, maintained, and viewed through shielding windows or by other remote viewing systems. 1.2.2 Consideration should be given to the need for specialized support equipment and tools early in the design process. 1.2.3 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conv...

DOE (Department of Energy) natural phenomena guidelines flood design and evaluation

International Nuclear Information System (INIS)

McCann, M.W.; Savy, J.B.

1989-01-01

Design and evaluation guidelines for DOE (Department of Energy) facilities subjected to earthquake, wind/tornado, and flood have been developed and presented in UCRL-15910 (Ref.1). This paper summarizes Chapter 6 of UCRL-15910 describing the philosophy and procedures for the design or evaluation of facilities for flood. The flood design and evaluation guidelines seek to ensure that DOE facilities satisfy the performance goals described in UCRL-15910. The guidelines are applicable to new and existing construction; however, in the evaluation of existing facilities, fewer design options may be available to satisfy the performance goals. Evaluation of the flood design for a facility consists of: (1) defining the design basis flood (DBFL), (2) evaluating site conditions (e.g., facility location, location of openings and doorways), and (3) assessing flood design strategies (e.g., build above DBFL levels, harden the site)

Selection of low-risk design guidelines for energetic events

International Nuclear Information System (INIS)

Ferguson, D.; Marchaterre, J.; Graham, J.

1982-01-01

This paper recommends the establishment of specific design guidelines for protection against potential, but low-probability, energetic events. These guidelines recognize the plant protective features incorporated to prevent such events, as well as the inherent capability of the plant to accommodate a certain level of energy release. Further, their application is recommended within the context of necessary standardized and agreed-upon acceptance criteria which are less restrictive than ASME code requirements. The paper provides the background upon which the selection of the design is made, including the characterization of energetic events dependent on various core-design parameters, and including the necessity of a low-risk design balanced between prevention of accidents and the mitigation of consequences

Margins related to equipment design

International Nuclear Information System (INIS)

Devos, J.

1994-01-01

Safety margins related to design of reactor equipment are defined according to safety regulations. Advanced best estimate methods are proposed including some examples which were computed and compared to experimental results. Best estimate methods require greater computation effort and more material data but give better variable accuracy and need careful experimental validation. Simplified methods compared to the previous are less sensitive to material data, sometimes are more accurate but very long to elaborate

Different types of superconductors: their effect on equipment design

International Nuclear Information System (INIS)

Ansart, A.; Manuel, P.; Fevrier, A.

1989-01-01

Development of superconductors for AC current and of higher critical temperature superconducting materials enlarged the field of research in cryoelectrotechnic. The paper discusses the materials characteristics in relation with the functional needs in the equipments. Are reviewed the main points governing conductor design for a given application, the characteristics and manufacturing technics for different superconducting materials. It is shown how lighter, smaller equipments can be designed as well as new ones for functions not covered with present apparatus. 17 refs [fr

The design guidelines of mobile augmented reality for tourism in Malaysia

Science.gov (United States)

Shukri, Saidatul A'isyah Ahmad; Arshad, Haslina; Abidin, Rimaniza Zainal

2017-10-01

Recent data shows that one in every five people in the world owns a Smartphone and spends most of their time on the phone using apps. Visitors prefer this type of portable, convenient, practical and simple technology when travelling, especially geo location-enabled applications such as the GPS. The aim of this paper is to develop design guidelines for Mobile Augmented Reality (MAR) for tourism. From the analysis of existing design guidelines of Mobile Augmented Reality (MAR) for tourism, an application design guidelines are proposed based on Human-computer interaction principle and usability design that would fulfils the user's requirement in a better way. Six design principles were examined in this analysis. The analysis identified eleven suggestions for design principles. These recommendations are offered towards designing principles and developing prototype app for tourist in Malaysia. This paper identifies design principles to reduce cognitive overhead of tourist, learn ability and suitable context for providing content whiles their travel in Malaysia.

Engineering electrodynamics electric machine, transformer, and power equipment design

CERN Document Server

Turowski, Janusz

2013-01-01

Due to a huge concentration of electromagnetic fields and eddy currents, large power equipment and systems are prone to crushing forces, overheating, and overloading. Luckily, power failures due to disturbances like these can be predicted and/or prevented.Based on the success of internationally acclaimed computer programs, such as the authors' own RNM-3D, Engineering Electrodynamics: Electric Machine, Transformer, and Power Equipment Design explains how to implement industry-proven modeling and design techniques to solve complex electromagnetic phenomena. Considering recent progress in magneti

Guidelines for equipment and staffing of radiotherapy facilities in the European countries: Final results of the ESTRO-HERO survey

International Nuclear Information System (INIS)

Dunscombe, Peter; Grau, Cai; Defourny, Noémie; Malicki, Julian; Borras, Josep M.; Coffey, Mary; Bogusz, Marta; Gasparotto, Chiara; Slotman, Ben; Lievens, Yolande; Kokobobo, Arianit; Sedlmayer, Felix; Slobina, Elena; De Hertogh, Olivier; Hadjieva, Tatiana; Petera, Jiri; Eriksen, Jesper Grau; Jaal, Jana; Bly, Ritva; Azria, David

2014-01-01

Background and purpose: In planning to meet evidence based needs for radiotherapy, guidelines for the provision of capital and human resources are central if access, quality and safety are not to be compromised. A component of the ESTRO-HERO (Health Economics in Radiation Oncology) project is to document the current availability and content of guidelines for radiotherapy in Europe. Materials and methods: An 84 part questionnaire was distributed to the European countries through their national scientific and professional radiotherapy societies with 30 items relating to the availability of guidelines for equipment and staffing and selected operational issues. Twenty-nine countries provided full or partial evaluable responses. Results: The availability of guidelines across Europe is far from uniform. The metrics used for capital and human resources are variable. There seem to have been no major changes in the availability or specifics of guidelines over the ten-year period since the QUARTS study with the exception of the recent expansion of RTT staffing models. Where comparison is possible it appears that staffing for radiation oncologists, medical physicists and particularly RTTs tend to exceed guidelines suggesting developments in clinical radiotherapy are moving faster than guideline updating. Conclusion: The efficient provision of safe, high quality radiotherapy services would benefit from the availability of well-structured guidelines for capital and human resources, based on agreed upon metrics, which could be linked to detailed estimates of need

Design Guidelines for Coffee Vending Machines

OpenAIRE

Schneidermeier, Tim; Burghardt, Manuel; Wolff, Christian

2013-01-01

Walk-up-and-use-systems such as vending and self-service machines request special attention concerning an easy to use and self-explanatory user interface. In this paper we present a set of design guidelines for coffee vending machines based on the results of an expert-based usability evaluation of thirteen different models.

Evolution of design concepts for remotely maintainable equipment racks

International Nuclear Information System (INIS)

Peishel, F.L.; Mouring, R.W.; Schrock, S.L.

1986-01-01

Equipment racks have been used to support process equipment in radioactive facilities for many years. Improvements in the design of these racks have evolved relatively slowly primarily as a result of limitations in the capabilities of maintenance equipment; that is, tasks could only be approached from above using bridge cranes with viewing primarily through periscopes. In recent years, however, technological advances have been made by the Consolidated Fuel Reprocessing Program (CFRP) at Oak Ridge National Laboratory (ORNL) in bridge-mounted servomanipulators with onboard auxiliary hoists and television viewing systems. These advances permit full cell coverage by the manipulator arms which, in turn, allow maintenance tasks to be approached horizontally as well as from above. Maintainable equipment items can be stacked vertically on a rack because total overhead access is less important and maintenance tasks that would not have been attempted in the past can now be performed. These advances permit greater flexibility in the design and cell layout of the racks and lead to concepts that could significantly increase the availability of a facility. The evolution of rack design and a description of the alternative concepts based on present maintenance systems capabilities are presented in this paper. 13 refs., 11 figs

Expert validation of fit-for-purpose guidelines for designing programmes of assessment

Directory of Open Access Journals (Sweden)

Dijkstra Joost

2012-04-01

Full Text Available Abstract Background An assessment programme, a purposeful mix of assessment activities, is necessary to achieve a complete picture of assessee competence. High quality assessment programmes exist, however, design requirements for such programmes are still unclear. We developed guidelines for design based on an earlier developed framework which identified areas to be covered. A fitness-for-purpose approach defining quality was adopted to develop and validate guidelines. Methods First, in a brainstorm, ideas were generated, followed by structured interviews with 9 international assessment experts. Then, guidelines were fine-tuned through analysis of the interviews. Finally, validation was based on expert consensus via member checking. Results In total 72 guidelines were developed and in this paper the most salient guidelines are discussed. The guidelines are related and grouped per layer of the framework. Some guidelines were so generic that these are applicable in any design consideration. These are: the principle of proportionality, rationales should underpin each decisions, and requirement of expertise. Logically, many guidelines focus on practical aspects of assessment. Some guidelines were found to be clear and concrete, others were less straightforward and were phrased more as issues for contemplation. Conclusions The set of guidelines is comprehensive and not bound to a specific context or educational approach. From the fitness-for-purpose principle, guidelines are eclectic, requiring expertise judgement to use them appropriately in different contexts. Further validation studies to test practicality are required.

FPGA Design Methodologies Applicable to Nuclear Power Plants

International Nuclear Information System (INIS)

Kwong, Yongil; Jeong, Choongheui

2013-01-01

In order to solve the above problem, NPPs in some countries such as the US, Canada and Japan have already applied FPGA-based equipment which has advantages as follows: It is easier to verify the performance because it needs only HDL code to configure logic circuits without other software, compared to microprocessor-based equipment, It is much cheaper than ASIC in a small quantity, Its logic circuits are re configurable, It has enough resources like logic blocks and memory blocks to implement I and C functions, Multiple functions can be implemented in a FPGA chip, It is stronger with respect to carboy security than microprocessor-based equipment because its configuration cannot be changed by external access, It is simple to replace it with new one when it is obsolete, Its power consumption is lower. However, FPGA-based equipment does not have only the merits. There are some issues on its application to NPPs. First of all, the experiences in applying it to NPPs are much less than to other industries, and international standards or guidelines are also very few. And there is the small number of FPGA platforms for I and C systems. Finally, the specific guidelines on FPGA design are required because the design has both hardware and software characteristics. In order to handle the above issues, KINS(Korea Institute of Nuclear Safety) built a test platform last year and have developed regulatory guidelines for FPGA-application in NPPs. I and C systems of NPPs have been increasingly using FPGA-based equipment as an alternative of microprocessor-based equipment which is not simple to be evaluated for safety due to its complexity. This paper explained the FPGA design flow and design guidelines. Those methodologies can be used as the guidelines on FPGA verification for safety of I and C systems

Severe accident management guidelines tool

International Nuclear Information System (INIS)

Gutierrez Varela, Javier; Tanarro Onrubia, Augustin; Martinez Fanegas, Rafael

2014-01-01

Severe Accident is addressed by means of a great number of documents such as guidelines, calculation aids and diagnostic trees. The response methodology often requires the use of several documents at the same time while Technical Support Centre members need to assess the appropriate set of equipment within the adequate mitigation strategies. In order to facilitate the response, TECNATOM has developed SAMG TOOL, initially named GGAS TOOL, which is an easy to use computer program that clearly improves and accelerates the severe accident management. The software is designed with powerful features that allow the users to focus on the decision-making process. Consequently, SAMG TOOL significantly improves the severe accident training, ensuring a better response under a real situation. The software is already installed in several Spanish Nuclear Power Plants and trainees claim that the methodology can be followed easier with it, especially because guidelines, calculation aids, equipment information and strategies availability can be accessed immediately (authors)

Energy Design Guidelines for High Performance Schools: Arctic and Subarctic Climates

Energy Technology Data Exchange (ETDEWEB)

2004-11-01

The Energy Design Guidelines for High Performance Schools--Arctic and Subarctic Climates provides school boards, administrators, and design staff with guidance to help them make informed decisions about energy and environmental issues important to school systems and communities. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school in arctic and subarctic climates. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs.

Simplified static method for determining seismic loads on equipment in moderate and high hazard facilities

International Nuclear Information System (INIS)

Scott, M.A.; Holmes, P.A.

1991-01-01

A simplified static analysis methodology is presented for qualifying equipment in moderate and high-hazard facility-use category structures, where the facility use is defined in Design and Evaluation Guidelines for Department of Energy Facilities Subjected to Natural Phenomena Hazards, UCRL-15910. Currently there are no equivalent simplified static methods for determining seismic loads on equipment in these facility use categories without completing dynamic analysis of the facility to obtain local floor accelerations or spectra. The requirements of UCRL-15910 specify the use of open-quotes dynamicclose quotes analysis methods, consistent with Seismic Design Guidelines for Essential Buildings, Chapter 6, open-quotes Nonstructural Elements,close quotes TM5-809-10-1, be used for determining seismic loads on mechanical equipment and components. Chapter 6 assumes that the dynamic analysis of the facility has generated either floor response spectra or model floor accelerations. These in turn are utilized with the dynamic modification factor and the actual demand and capacity ratios to determine equipment loading. This complex methodology may be necessary to determine more exacting loads for hard to qualify equipment but does not provide a simple conservative loading methodology for equipment with ample structural capacity

Designing User-Computer Dialogues: Basic Principles and Guidelines.

Science.gov (United States)

Harrell, Thomas H.

This discussion of the design of computerized psychological assessment or testing instruments stresses the importance of the well-designed computer-user interface. The principles underlying the three main functional elements of computer-user dialogue--data entry, data display, and sequential control--are discussed, and basic guidelines derived…

Manual on Safety Aspects of the Design and Equipment of Hot Laboratories

International Nuclear Information System (INIS)

1969-01-01

With the development of atomic energy application and research, hot laboratories are now being constructed in a number of countries. The present publication describes and discusses experience in several countries in designing equipment for these laboratories. The safe handling of highly radioactive substances is the main purpose of hot laboratory design and equipment. The manual aims at helping those persons, particularly in the developing countries, who plan to design and construct a new hot laboratory or modify an existing one. It does not deal in great detail with the engineering design of protective and handling equipment; these matters can be found in the comprehensive list of references. The manual itself covers only basic ideas and different approaches in the design of laboratory building, hot cells, shielded and glove boxes, fume cupboards, and handling and viewing equipment. Systems for transferring materials and main services are also discussed.

Environmental Design Guidelines for Low Crested Coastal Structures

DEFF Research Database (Denmark)

Burcharth, Hans F.; Hawkins, Stephen J.; Zanuttigh, Barbara

selected to represent a variety of environmental conditions (Chapter 11); the application of the proposed methodology to a real prototype case, in order to give a practical example to designers (Chapter 12). The third part contains all the formulae and tools to help engineers (Chapter 13), ecologists....... The guidelines have been drafted in a generic way to be appropriate throughout the European Union taking into regard current European Commission policy and directives to promote sustainable development and integrated coastal zone management. The guidelines are composed of three main parts. The first part...... (Chapters 1-10) contains the description of the design methodology, from the preliminary identification of design alternatives till the selection of the sustainable scheme and its construction. The second part presents: the analysis of the performance of beach defences in DELOS study sites, which were...

Communication received from certain member states regarding guidelines for the export of nuclear material, equipment and technology

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-02-24

The document contains the text of note verbales dated 30 September 1997 received by the Director General of the IAEA from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, Japan, the Republic of Korea, New Zealand, Norway, Poland, Portugal, Romania, the Russian Federation, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to export of nuclear material, equipment and technology. The purpose of the notes verbale is to provide further information about the Guidelines for Transfers of Nuclear-related Dual-use Equipment, material and related Technology in accordance with which the relevant Governments act.

Communication received from certain member states regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1998-01-01

The document contains the text of note verbales dated 30 September 1997 received by the Director General of the IAEA from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, France, Germany, Greece, Hungary, Ireland, Italy, Japan, the Republic of Korea, New Zealand, Norway, Poland, Portugal, Romania, the Russian Federation, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to export of nuclear material, equipment and technology. The purpose of the notes verbale is to provide further information about the Guidelines for Transfers of Nuclear-related Dual-use Equipment, material and related Technology in accordance with which the relevant Governments act

Influence of different outdoor design conditions on design cooling load and design capacities of air conditioning equipments

International Nuclear Information System (INIS)

Aktacir, Mehmet Azmi; Bueyuekalaca, Orhan; Bulut, Huesamettin; Yilmaz, Tuncay

2008-01-01

Outdoor design conditions are important parameters for energy efficiency of buildings. The result of incorrect selection of outdoor design conditions can be dramatic in view of comfort and energy consumption. In this study, the influence of different outdoor design conditions on air conditioning systems is investigated. For this purpose, cooling loads and capacities of air conditioning equipments for a sample building located in Adana, Turkey are calculated using different outdoor design conditions recommended by ASHRAE, the current design data used in Turkey and the daily maximum dry and wet bulb temperatures of July 21st, which is generally accepted as the design day. The cooling coil capacities obtained from the different outdoor design conditions considered in this study are compared with each other. The cost analysis of air conditioning systems is also performed. It is seen that the selection of outdoor design conditions is a very critical step in calculation of the building cooling loads and design capacities of air conditioning equipments

Development of human factors design review guidelines(II)

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Oh, In Suk; Suh, Sang Moon; Lee, Hyun Chul [Korea Atomic Energy Research Institute, Taejon (Korea)

1998-06-01

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: 25. Human Factors Engineering Program Review Model and 26. Review Criteria for Human Factors Aspects of Advanced Controls and Instrumentation, which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and reviewing the reference documents of NUREG-0711. We also computerized the Korean version of NUREG-0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm systems. Then we will update the guidelines by reviewing the literature related to alarm design published after 1994. (author). 11 refs., 2 figs., 2 tabs.

46 CFR 130.220 - Design of equipment for cooking and heating.

Science.gov (United States)

2010-10-01

... 46 Shipping 4 2010-10-01 2010-10-01 false Design of equipment for cooking and heating. 130.220... Design of equipment for cooking and heating. (a) Doors on each cooking appliance must be provided with heavy-duty hinges and locking-devices to prevent accidental opening in heavy weather. (b) Each cooking...

On fundamental concept of anti-earthquake design of equipment and pipings

International Nuclear Information System (INIS)

Shibata, H.; Kato, M.

1979-01-01

This paper deals with a new concept of anti-earthquake design of equipment and pipings in nuclear power plants. Usual anti-earthquake design of such items starts from the design basis ground motions, via floor responses and ends at the stress analysis of each structural element. However, the same type of equipment are used for plants under various site conditions. The ordinarily used method obliges the repetition of such design procedure on each plant. This new design method has been developed to avoid such time-consuming repetitions. (orig.)

Evidence-based guidelines for the wise use of computers by children: physical development guidelines.

Science.gov (United States)

Straker, L; Maslen, B; Burgess-Limerick, R; Johnson, P; Dennerlein, J

2010-04-01

Computer use by children is common and there is concern over the potential impact of this exposure on child physical development. Recently principles for child-specific evidence-based guidelines for wise use of computers have been published and these included one concerning the facilitation of appropriate physical development. This paper reviews the evidence and presents detailed guidelines for this principle. The guidelines include encouraging a mix of sedentary and whole body movement tasks, encouraging reasonable postures during computing tasks through workstation, chair, desk, display and input device selection and adjustment and special issues regarding notebook computer use and carriage, computing skills and responding to discomfort. The evidence limitations highlight opportunities for future research. The guidelines themselves can inform parents and teachers, equipment designers and suppliers and form the basis of content for teaching children the wise use of computers. STATEMENT OF RELEVANCE: Many children use computers and computer-use habits formed in childhood may track into adulthood. Therefore child-computer interaction needs to be carefully managed. These guidelines inform those responsible for children to assist in the wise use of computers.

Equipment designs for the spent LWR fuel dry storage demonstration

International Nuclear Information System (INIS)

Steffen, R.J.; Kurasch, D.H.; Hardin, R.T.; Schmitten, P.F.

1980-01-01

In conjunction with the Spent Fuel Handling and Packaging Program (SFHPP) equipment has been designed, fabricated and successfully utilized to demonstrate the packaging and interim dry storage of spent LWR fuel. Surface and near surface storage configurations containing PWR fuel assemblies are currently on test and generating baseline data. Specific areas of hardware design focused upon include storage cell components and the support related equipment associated with encapsulation, leak testing, lag storage, and emplacement operations

A study on developpement of guideline on writing technical document for electrical medical devices: Dental x-ray equipment

Energy Technology Data Exchange (ETDEWEB)

Lee, Seung Youl; Kim, Jae Ryang; Lee, Jun Ho; Park, Chang Won [Division of Medical Device Research, National Institute of Food and Drug Safety Evaluation, Mnistry of Food and Drug Safety (Korea, Republic of)

2016-12-15

Due to recent population aging, the number of check-up for senior citizens has increased steadily. According to this trend, the market size of dental X-ray equipment and the number of approval and review for these devices have simultaneously increased. The technical document of medical device is required for approval and review for medical device, and medical device companies needs to have work comprehension and expertise, as the document needs to include the overall contents such as performances, test criteria, etc.. Yet, since most of domestic manufacturers or importers of medical devices are small businesses, it is difficult for them to recruit professional manpower for approval of medical devices, and submission of inaccurate technical documents has increased. These problems lead to delay of the approval process and to difficulties in quick entering into the market. Especially, the Ministry of Food and Drug safety (MFDS) standards of a dental extra-oral X-ray equipment, a dental intra-oral X-ray equipment, an arm-type computed tomography, and a portable X-ray system have been recently enacted or not. this guideline of dental X-ray equipment adjusting revised standards was developed to help relative companies and reviewers. For this study, first, the methods to write technical document have been reviewed with revised international and domestic regulations and system. Second, the domestic and foreign market status of each item has been surveyed and analyzed. Third, the contents of technical documents already approved by MFDS have been analyzed to select the correct example, test items, criteria, and methods. Finally, the guideline has been developed based on international and domestic regulation, through close review of a consultative body composed of academic, industrial, research institute and government experts.

A study on developpement of guideline on writing technical document for electrical medical devices: Dental x-ray equipment

International Nuclear Information System (INIS)

Lee, Seung Youl; Kim, Jae Ryang; Lee, Jun Ho; Park, Chang Won

2016-01-01

Due to recent population aging, the number of check-up for senior citizens has increased steadily. According to this trend, the market size of dental X-ray equipment and the number of approval and review for these devices have simultaneously increased. The technical document of medical device is required for approval and review for medical device, and medical device companies needs to have work comprehension and expertise, as the document needs to include the overall contents such as performances, test criteria, etc.. Yet, since most of domestic manufacturers or importers of medical devices are small businesses, it is difficult for them to recruit professional manpower for approval of medical devices, and submission of inaccurate technical documents has increased. These problems lead to delay of the approval process and to difficulties in quick entering into the market. Especially, the Ministry of Food and Drug safety (MFDS) standards of a dental extra-oral X-ray equipment, a dental intra-oral X-ray equipment, an arm-type computed tomography, and a portable X-ray system have been recently enacted or not. this guideline of dental X-ray equipment adjusting revised standards was developed to help relative companies and reviewers. For this study, first, the methods to write technical document have been reviewed with revised international and domestic regulations and system. Second, the domestic and foreign market status of each item has been surveyed and analyzed. Third, the contents of technical documents already approved by MFDS have been analyzed to select the correct example, test items, criteria, and methods. Finally, the guideline has been developed based on international and domestic regulation, through close review of a consultative body composed of academic, industrial, research institute and government experts

Design Guidelines of a Spring-Damper System for Emergency Diesel Generator Sets

Energy Technology Data Exchange (ETDEWEB)

Kim, Min Kyu; Choun, Young Sun; Seo, Jeong Moon

2007-05-15

This guidelines described about the procedure of isolation system design for Emergency Diesel Generator (EDG) of Nuclear Power Plant (NPP). First of all, a vibration concept including the ground vibration was described and vibration control system and seismic isolation system were considered. The behavior characteristics and design consideration of coil spring-viscose damper system were summarized. The material properties of foundation of EDG system and the ground were considered. A design load and seismic load for isolation system design were described and an analysis method was explained. Finally, a design example for an EDG in Yonggwang Nuclear Unit 5 and 6 was attached of Appendix. First of all, this design guideline can apply to design of a vibration and seismic isolation system for EDG system and the design example present a design procedure practically. Moreover, this design guideline can be used for isolation design of other rotational machines and other isolation system except spring-damper system.

Reliable design of electronic equipment an engineering guide

CERN Document Server

Natarajan, Dhanasekharan

2014-01-01

This book explains reliability techniques with examples from electronics design for the benefit of engineers. It presents the application of de-rating, FMEA, overstress analyses and reliability improvement tests for designing reliable electronic equipment. Adequate information is provided for designing computerized reliability database system to support the application of the techniques by designers. Pedantic terms and the associated mathematics of reliability engineering discipline are excluded for the benefit of comprehensiveness and practical applications. This book offers excellent support

Toward best practice in Human Machine Interface design for older drivers: A review of current design guidelines.

Science.gov (United States)

Young, K L; Koppel, S; Charlton, J L

2017-09-01

Older adults are the fastest growing segment of the driving population. While there is a strong emphasis for older people to maintain their mobility, the safety of older drivers is a serious community concern. Frailty and declines in a range of age-related sensory, cognitive, and physical impairments can place older drivers at an increased risk of crash-related injuries and death. A number of studies have indicated that in-vehicle technologies such as Advanced Driver Assistance Systems (ADAS) and In-Vehicle Information Systems (IVIS) may provide assistance to older drivers. However, these technologies will only benefit older drivers if their design is congruent with the complex needs and diverse abilities of this driving cohort. The design of ADAS and IVIS is largely informed by automotive Human Machine Interface (HMI) guidelines. However, it is unclear to what extent the declining sensory, cognitive and physical capabilities of older drivers are addressed in the current guidelines. This paper provides a review of key current design guidelines for IVIS and ADAS with respect to the extent they address age-related changes in functional capacities. The review revealed that most of the HMI guidelines do not address design issues related to older driver impairments. In fact, in many guidelines driver age and sensory cognitive and physical impairments are not mentioned at all and where reference is made, it is typically very broad. Prescriptive advice on how to actually design a system so that it addresses the needs and limitations of older drivers is not provided. In order for older drivers to reap the full benefits that in-vehicle technology can afford, it is critical that further work establish how older driver limitations and capabilities can be supported by the system design process, including their inclusion into HMI design guidelines. Copyright © 2016 Elsevier Ltd. All rights reserved.

Reliability Based Calibration of Fatigue Design Guidelines for Ship Structures

DEFF Research Database (Denmark)

Folsø, Rasmus; Otto, S.; Parmentier, G.

2002-01-01

A simple reliability based framework is applied to calibrate a new set of fatigue design guidelines. This new guideline considers two different approaches for the assessment of both loads, stresses and local stress raising effects, and partial safety factors must be given for any combination...

Electric heating guidelines: power smart home; 2. ed.

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

Guidelines, for use by B. C. Hydro, were established for proper planning and design of an electric heating system for residential buildings. The guidebook is divided into five sections: (1) comfort and electric heating systems, (2) contractors` guide to heat loss calculation, (3) imperial heat loss factors, (4) metric heat loss factors, and (5) installation guidelines for electric heating systems. Individual topics discussed include heat loss and the human body, heating systems and comfort, heat loss design, air leakage, and soil conductivity factors. Design considerations and equipment standards were described for the following electric heating systems: electric resistance baseboard systems, forced flow unitary heaters, electric radiant cable in-floor systems, radiant ceiling systems, forced warm air heating systems, furnaces, and heat pumps. 68 tabs., 29 figs.

Emplacement and retrieval equipment design considerations for a repository in salt

International Nuclear Information System (INIS)

Nair, B.R.; Bahorich, R.J.

1987-01-01

The current design concept for the disposal of nuclear high level waste packages in a repository in salt is based on the emplacement of individual packages in vertical boreholes in the underground mine floor. A key requirement is that the waste packages be capable of being retrieved during the last 26 years of the 76-year repository operating period. The unique design considerations relating to the retrieval of waste packages emplaced in bedded salt are presented in this paper. The information is based on the experience developed during the design of vertical emplacement and retrieval equipment in support of the Sandia Defense High Level Waste experiments at the Waste Isolation Pilot Plant. Also included are the impact of retrievability on the design of the equipment, the special salt cutting technology that was developed for this application, and a description of the equipment

Two tools for environmentally conscious designers and product developers of electrical & electronic equipment (EEE)

DEFF Research Database (Denmark)

Poll, Christian; Hauschild, Michael Zwicky; Olsen, Stig Irving

2002-01-01

The paper presents the two tools 1)"Product families - short cuts to environmental knowledge" and 2)"Eco-conscious design of electrical & electronic equipment (EEE)". Tool 1) comes in form of a handbook. The purpose of this handbook is to ease the work with developing more environmentally sound...... products, thus giving guidelines for development of new products without the companies themselves having to perform an LCA. The handbook describes 5 productfamilies: mobile phones, vacuum cleaners, industrial valves with electronic controls, lighting, ventilation. Tool 2) comes in form of a software tool...... with built in training, guidance, references, calculator and database. The tool provides the basic understanding of how EEE-products in general interact with the environment. The tool gives an overview of the tasks and responsibilities involved in Eco-Desing, and examples of how to choose and quantify...

Design and construction of the Portable Industrial X-Ray Equipment

International Nuclear Information System (INIS)

Nguyen Phuc; Nguyen Van Si; Le Tien Quan; Trinh Anh Tuan; Nguyen Manh Hung; Trinh Dinh Tuong

2011-01-01

The main purposes of the project are the supporting to design and construction of the Portable Industrial X-Ray Equipment; with the accuracy ±2% of Output High Voltage 200 kV and Tube current 5 mA. The Equipment is composed of control unit, X-ray generator, and power cable, connection cable. X-ray generator is assembling construction X-ray tube, H.V transformer together with gas insulation (SF6) are sealed up in aluminum bucked cabinet, fan and heat-sink are mounted in the end of X-ray generator as cooling, SF6 is a gas electrical performance to H.V. Alarm lamp is used to warn, flashing, show generating X-ray. Control unit is box construction. Four printed circuit boards (PCB) and electronic device are mounted in it. All operating buttons switches and displays are equipped on the panel. We have completed to design and construct the Portable Industrial X-Ray Equipment; and have tested the electronic parameters of all test points and the main parameters of equipment (the accuracy ±2% of Output High Voltage 200 kV and Tube current 5 mA). We also have successful used the Portable Industrial X-Ray Equipment to evaluate the welds in industry. (author)

Advanced human-system interface design review guideline. General evaluation model, technical development, and guideline description

International Nuclear Information System (INIS)

O'Hara, J.M.

1994-07-01

Advanced control rooms will use advanced human-system interface (HSI) technologies that may have significant implications for plant safety in that they will affect the operator's overall role in the system, the method of information presentation, and the ways in which operators interact with the system. The U.S. Nuclear Regulatory Commission (NRC) reviews the HSI aspects of control rooms to ensure that they are designed to good human factors engineering principles and that operator performance and reliability are appropriately supported to protect public health and safety. The principal guidance available to the NRC, however, was developed more than ten years ago, well before these technological changes. Accordingly, the human factors guidance needs to be updated to serve as the basis for NRC review of these advanced designs. The purpose of this project was to develop a general approach to advanced HSI review and the human factors guidelines to support NRC safety reviews of advanced systems. This two-volume report provides the results of the project. Volume I describes the development of the Advanced HSI Design Review Guideline (DRG) including (1) its theoretical and technical foundation, (2) a general model for the review of advanced HSIs, (3) guideline development in both hard-copy and computer-based versions, and (4) the tests and evaluations performed to develop and validate the DRG. Volume I also includes a discussion of the gaps in available guidance and a methodology for addressing them. Volume 2 provides the guidelines to be used for advanced HSI review and the procedures for their use

Advanced human-system interface design review guideline. General evaluation model, technical development, and guideline description

Energy Technology Data Exchange (ETDEWEB)

O`Hara, J.M.

1994-07-01

Advanced control rooms will use advanced human-system interface (HSI) technologies that may have significant implications for plant safety in that they will affect the operator`s overall role in the system, the method of information presentation, and the ways in which operators interact with the system. The U.S. Nuclear Regulatory Commission (NRC) reviews the HSI aspects of control rooms to ensure that they are designed to good human factors engineering principles and that operator performance and reliability are appropriately supported to protect public health and safety. The principal guidance available to the NRC, however, was developed more than ten years ago, well before these technological changes. Accordingly, the human factors guidance needs to be updated to serve as the basis for NRC review of these advanced designs. The purpose of this project was to develop a general approach to advanced HSI review and the human factors guidelines to support NRC safety reviews of advanced systems. This two-volume report provides the results of the project. Volume I describes the development of the Advanced HSI Design Review Guideline (DRG) including (1) its theoretical and technical foundation, (2) a general model for the review of advanced HSIs, (3) guideline development in both hard-copy and computer-based versions, and (4) the tests and evaluations performed to develop and validate the DRG. Volume I also includes a discussion of the gaps in available guidance and a methodology for addressing them. Volume 2 provides the guidelines to be used for advanced HSI review and the procedures for their use.

Development of human factors design review guidelines(III)

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Oh, In Suk; Suh, Sang Moon; Lee, Hyun Chul [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1999-02-15

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: '25, human factors engineering program review model' and '26, review criteria for human factors aspects of advanced controls and instrumentation', which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and reviewing the reference documents NUREG--0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm system. Then we will update the guidelines by reviewing the literature related to alarm design published after 1994.

Development of human factors design review guidelines(III)

International Nuclear Information System (INIS)

Lee, Jung Woon; Oh, In Suk; Suh, Sang Moon; Lee, Hyun Chul

1999-02-01

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: '25, human factors engineering program review model' and '26, review criteria for human factors aspects of advanced controls and instrumentation', which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and reviewing the reference documents NUREG--0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm system. Then we will update the guidelines by reviewing the literature related to alarm design published after 1994

Development of human factors design review guidelines(II)

International Nuclear Information System (INIS)

Lee, Jung Woon; Oh, In Suk; Suh, Sang Moon; Lee, Hyun Chul

1998-06-01

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: '25, human factors engineering program review model' and '26, review criteria for human factors aspects of advanced controls and instrumentation', which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and reviewing the reference documents NUREG--0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm system. Then we will update the guidelines by reviewing the literature related to alarm design published after 1994

Development of human factors design review guidelines(III)

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Oh, In Suk; Suh, Sang Moon; Lee, Hyun Chul [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1999-02-15

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: '25, human factors engineering program review model' and '26, review criteria for human factors aspects of advanced controls and instrumentation', which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and reviewing the reference documents NUREG--0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guides in KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm system. Then we will update the guidelines by reviewing the literature related to alarm design published after 1994.

Design and construction rules for electrical equipments of nuclear islands. 3. ed.

International Nuclear Information System (INIS)

1993-01-01

The French design and construction for electrical equipments of nuclear islands (RCC-E) deals with equipments of which the failure may have consequences on the safety of persons or appreciable effects on the availability of the power plant. This book presents the rules concerning (1) qualification procedure, (2) the design of functional units, (3) the installation (environmental conditions, protection rules), (4) the constituent elements of equipments, (5) the control and testing methods

The selection of low-risk design guidelines for energetic events

International Nuclear Information System (INIS)

Fergusson, Donald; Marchaterre, John; Graham, John

1982-01-01

This paper recommends the establishment of specific design guidelines for protection against potential, but low probability, energetic events. These guidelines recognize the plant protective features incorporated to prevents such events, as well as the inherent capability of the plant to accommodate a certain level of energy release. Further, their application is recommended within the context of necessary standardized and agreed upon acceptance criteria which are less restrictive than ASME code requirements. The paper provides the background upon which the selection of the design is made, including the characterization of energetic events dependent on various core-design parameters, and including the necessity of a low-risk design balanced between prevention of accidents and the mitigation of consequences

Acceptance test procedure for K basins dose reduction project clean and coat equipment

International Nuclear Information System (INIS)

Creed, R.F.

1996-01-01

This document is the Acceptance Test Procedure (ATP) for the clean and coat equipment designed by Oceaneering Hanford, Inc. under purchase order MDK-XVC-406988 for use in the 105 K East Basin. The ATP provides the guidelines and criteria to test the equipment's ability to clean and coat the concrete perimeter, divider walls, and dummy elevator pit above the existing water level. This equipment was designed and built in support of the Spent Nuclear Fuel, Dose Reduction Project. The ATP will be performed at the 305 test facility in the 300 Area at Hanford. The test results will be documented in WHC-SD-SNF-ATR-020

System design description for master equipment list, phase I

International Nuclear Information System (INIS)

Sandoval, J.D.

1997-01-01

This System Design Description (SDD) is for the Master Equipment List Phase I (MEL). It has been prepared following the WI-IC-CM-3-10, ''Software Practices,'' (Ref. 6). This SDD describes the internal design for implementation of the MEL Phase I

Low activation diagnostic equipment design studies

International Nuclear Information System (INIS)

Hopkins, G.R.; Cheng, E.T.; Fisher, R.K.

1985-01-01

The low activation fusion concept has been applied to the diagnostic equipment in a fusion reactor. The components where fabrication from low activation materials is feasible have been identified. Other systems where higher activation elements are required can have their activation reduced by design approaches which include shielding and operation only in low flux regions of the reactor. Some components will not operate in a high flux so activation is not a major concern. This low activation diagnostic equipment study completes a series of low activation studies where all the components in a fusion power reactor have now been evaluated. It is concluded that a completely low activation fusion reactor is feasible with all components meeting the functional requirements. This provides an environmentally benign energy source with a high confidence level in meeting safety criteria in operation, maintenance and waste disposal

Wireless application guidelines for usability design and evaluation for developing countries

International Nuclear Information System (INIS)

Khoja, S.A.; Ursani, A.A.; Ali, A.

2009-01-01

The aim of this paper is to provide guidelines for designing wireless applications. These guidelines are developed with the help of Human Computer Interaction based Usability Evaluation surveys and tests results. These guidelines will help in making wireless applications more usable and attractive for users and will help designers to plan effective interactive applications. The guidelines presented in the paper have been derived from the results of surveys, usability tests and SET (Summative Evaluation Tests) carried out over 200 people of Karachi, Pakistan, from different walks of life with different academic and professional backgrounds, making imperative suggestions not only to improve the usability of exciting features given in wireless and mobile products, but also provide suggestions to improve usability of basic components such as, text, navigation, interactivity, multimedia, control and behavior. (author)

IFR fuel cycle process equipment design environment and objectives

International Nuclear Information System (INIS)

Rigg, R.H.

1993-01-01

Argonne National laboratory (ANL) is refurbishing the hot cell facility originally constructed with the EBR-II reactor. When refurbishment is complete, the facility win demonstrate the complete fuel cycle for current generation high burnup metallic fuel elements. These are sodium bonded, stainless steel clad fuel pins of U-Zr or U-Pu-Zr composition typical of the fuel type proposed for a future Integral Fast Reactor (IFR) design. To the extent possible, the process equipment is being built at full commercial scale, and the facility is being modified to incorporate current DOE facility design requirements and modem remote maintenance principles. The current regulatory and safety environment has affected the design of the fuel fabrication equipment, most of which will be described in greater detail in subsequent papers in this session

Virtual reality verification of workplace design guidelines for the process plant control room

International Nuclear Information System (INIS)

Droeivoldsmo, Asgeir; Nystad, Espen; Helgar, Stein

2001-02-01

Early identification of potential human factors guideline-violations and corrective input into the design process is desired for efficient and cost-effective control room design. Virtual reality (VR) technology makes it possible to perform evaluation of the design of the control room at an early stage of the design process, but can we trust the results from such evaluations? This paper describes an experimental validation of a VR model against the real world in five different guideline verification tasks. Results indicate that guideline verification in the VR model can be done with satisfactory accuracy for a number of evaluations. However, some guideline categories require further development of measurement tools and use of a model with higher resolution than the model used in this study. (Author). 30 refs., 4 figs., 1 tab

Consistent natural phenomena design and evaluation guidelines for U.S. Department of Energy facilities

International Nuclear Information System (INIS)

Murray, R.C.; Short, S.A.

1989-01-01

Uniform design and evaluation guidelines for protection against natural phenomena hazards such as earthquakes, extreme winds, and flooding for facilities at Department of Energy (DOE) sites throughout the United States have been developed. The guidelines apply to design of new facilities and to evaluation or modification of existing facilities. These guidelines are an approach for design or evaluation for mitigating the effects of natural phenomena hazards. These guidelines are intended to control the level of conservatism introduced in the design/evaluation process such that all hazards are treated on a reasonably consistent and uniform basis and such that the level of conservatism is appropriate for facility characteristics such as importance, cost, and hazards to on-site personnel, the general public, and the environment. The philosophy and goals of these guidelines are covered by this paper

Engineering policy guidelines for design of driven piles.

Science.gov (United States)

2011-08-01

These guidelines were developed as part of a comprehensive research program undertaken by the Missouri Department of : Transportation (MoDOT) to reduce costs associated with design and construction of bridge foundations while maintaining appropriate ...

Diagnostic x-ray equipment compliance and facility survey. Recommended procedures for equipment and facility testing

International Nuclear Information System (INIS)

1994-01-01

The Radiation Protection Bureau has set out guidelines for the testing of diagnostic x-ray equipment and facilities. This guide provides information for the x-ray inspector, test engineer, technologist, medical physicist and any other person responsible for verifying the regulatory compliance or safety of diagnostic x-ray equipment and facilities. Diagnostic x-radiation is an essential part of present day medical practice. The largest contributor of irradiation to the general population comes from diagnostic x-radiation. Although individual irradiations are usually small, there is a concern of possible excess cancer risk when large populations are irradiated. Unnecessary irradiations to patients from radiological procedures can be significantly reduced with little or no decrease in the value of medical diagnostic information. This can be achieved by using well designed x-ray equipment which is installed, used and maintained by trained personnel, and by the adoption of standardized procedures. In general, when patient surface dose is reduced, there is a corresponding decrease in dose to x-ray equipment operators and other health care personnel. 2 tabs., 4 figs

Diagnostic x-ray equipment compliance and facility survey. Recommended procedures for equipment and facility testing

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

The Radiation Protection Bureau has set out guidelines for the testing of diagnostic x-ray equipment and facilities. This guide provides information for the x-ray inspector, test engineer, technologist, medical physicist and any other person responsible for verifying the regulatory compliance or safety of diagnostic x-ray equipment and facilities. Diagnostic x-radiation is an essential part of present day medical practice. The largest contributor of irradiation to the general population comes from diagnostic x-radiation. Although individual irradiations are usually small, there is a concern of possible excess cancer risk when large populations are irradiated. Unnecessary irradiations to patients from radiological procedures can be significantly reduced with little or no decrease in the value of medical diagnostic information. This can be achieved by using well designed x-ray equipment which is installed, used and maintained by trained personnel, and by the adoption of standardized procedures. In general, when patient surface dose is reduced, there is a corresponding decrease in dose to x-ray equipment operators and other health care personnel. 2 tabs., 4 figs.

Design patterns for modelling guidelines

NARCIS (Netherlands)

Serban, Radu; Ten Teije, Annette; Marcos, Mar; Polo-Conde, Cristina; Rosenbrand, Kitty C J G M; Wittenberg, Jolanda; van Croonenborg, Joyce

2005-01-01

It is by now widely accepted that medical guidelines can help to significantly improve the quality of medical care. Unfortunately, constructing the required medical guidelines is a very labour intensive and costly process. The cost of guideline construction would decrease if guidelines could be

Engineering policy guidelines for design of earth slopes.

Science.gov (United States)

2011-10-01

These guidelines were developed as part of a comprehensive research program undertaken by the Missouri Department of Transportation (MoDOT) to reduce costs associated with design and construction of bridge foundations while maintaining appropriate le...

Engineering policy guidelines for design of spread footings.

Science.gov (United States)

2011-10-01

These guidelines were developed as part of a comprehensive research program undertaken by the Missouri Department of Transportation (MoDOT) to reduce costs associated with design and construction of bridge foundations while maintaining appropriate le...

Engineering policy guidelines for design of drilled shafts.

Science.gov (United States)

2011-10-01

These guidelines were developed as part of a comprehensive research program undertaken by the Missouri Department of Transportation (MoDOT) to reduce costs associated with design and construction of bridge foundations while maintaining appropriate le...

Guideline on dependability management for the power industry: detailed description of international power plant equipment dependability indicators

International Nuclear Information System (INIS)

Procaccia, H.; Silberberg, S.

1997-01-01

Dependability Management involves the management of reliability, availability maintainability and maintenance support, and in the power industry is necessary to ensure that plant meets the Reliability, Availability and Maintainability (RAM) targets set by the Utilities. In 1993, a joint Standard on Dependability Programme Management - Part 1: Dependability Programme Management), ISO 9000-': 1993 (Quality Management and Quality Assurance Standards - Part 4: Guide to Dependability Programme Management). UNIPEDE established a group of experts (Nulethermaint) to produce guidelines on its implementation specifically for use in the power industry. The present document comprises Part 2 OF THE UNIPEDE plant performance indicators and can be applied to both nuclear and fossil plant. There are five different equipment dependability indicators, all relating to equipment maintenance activities and the impact that these activities have on the loss of both system function and unit capability. Per year, each of the indicators can be applied separately to both preventive maintenance and corrective maintenance, giving rise to as many as ten indicator values for each item of equipment. Used in this way, the indicators provide a comprehensive picture of the maintenance strategy employed for key pieces of equipment, and its effectiveness. They are, therefore, a valuable managerial tool for improving maintenance activities at the unit level within a utility. This document provides guidance on the division of both nuclear and fossil power plant into their component parts and in each case the types of equipment having the most dominant effect on dependability are identified. These are the items which merit the greatest attention with regard to the equipment dependability indicators. (authors)

Guideline from Japanese Society of Echocardiography: 2018 focused update incorporated into Guidance for the Management and Maintenance of Echocardiography Equipment.

Science.gov (United States)

Daimon, Masao; Akaishi, Makoto; Asanuma, Toshihiko; Hashimoto, Shuji; Izumi, Chisato; Iwanaga, Shiro; Kawai, Hiroya; Toide, Hiroyuki; Hayashida, Akihiro; Yamada, Hirotsugu; Murata, Mitsushige; Hirano, Yutaka; Suzuki, Kengo; Nakatani, Satoshi

2018-03-01

Echocardiography plays a pivotal role as an imaging modality in the modern cardiology practice. Information derived from echocardiography is definitely helpful for a patient care. The Japanese Society of Echocardiography has promoted echocardiography for a routine clinical and research use. One of the missions of the Society is to provide information that is useful for high-quality examinations. To ensure it, we believe equipment in good conditions and a comfortable environment are important for both a patient and an examiner. Thus, the Committee for Guideline Writing, the Japanese Society of Echocardiography published brief guidance for the routine use of echocardiography equipment in 2015. Recently, the importance of international standardization has been emphasized in the medical laboratories. Accordingly, the committee has revised and updated our guidance for the routine use of echocardiography equipment.

Aging management guidelines for commercial nuclear power plant equipment

International Nuclear Information System (INIS)

Nakos, J.T.; Gazdzinski, R.F.; Toman, G.J.

1994-01-01

The US Department of Energy, in cooperation with the Electric Power Research Institute and nuclear power plant utilities, has prepared ''Aging Management Guidelines'' (AMGs) for commodity types of equipment (e.g., pumps, electrical switchgear) important to license renewal. For the most part, this is also consistent with the Maintenance Rule, 10 CFR 50.65 (1991). AMGs concentrate on technical, (not licensing) issues and are directed toward systems engineers and plant maintenance staff. AMGs include a detailed summary of operating history, stressors, aging mechanisms, and various types of maintenance practices that can be combined to create effective programs that manage aging. All aging mechanisms were addressed; no attempt was made to limit the evaluation to aging mechanisms ''unique to license renewal,'' as defined in the License Renewal Rule, 10 CFR 54 (1991). The first AMG on Electrical Switchgear was published in July 1993. Six (6) additional AMGs will be published by the first quarter of calendar year 1994. It is anticipated that two more AMGs will be started in 1994. The seven ongoing AMG topics are as follows: (1) battery chargers, inverters and uninterruptible power supplies; (2) batteries, stationary; (3) heat exchangers; (4) motor control centers; (5) pumps; (6) switchgear, electric; (7) transformers, power and distribution. In Section 7, industry feedback regarding AMGs is discussed. Overall, the response has been very positive

IEEE standard for design qualification of safety systems equipment used in nuclear power generating stations

International Nuclear Information System (INIS)

Anon.

1980-01-01

This standard is written to serve as a general standard for qualification of all types of safety systems equipment, mechanical and instrumentation as well as electrical. It also establishes principles and procedures to be followed in preparing specific safety systems equipment standards. Guidance for qualifying specific safety systems equipment may be found in various specific equipment qualification standards that are now available or are being prepared. It is required that safety systems equipment in nuclear power generating stations meet or exceed its performance requirements throughout its installed life. This is accomplished by a disciplined program of design qualification and quality assurance of design, production, installation, maintenance and surveillance. This standard is for the design qualification section of the program only. Design qualification is intended to demonstrate the capability of the equipment design to perform its safety function(s) over the expected range of normal, abnormal, design basis event, post design basis event, and in-service test conditions. Inherent to design qualification is the requirement for demonstration, within limitations afforded by established technical state-of-the-art, that in-service aging throughout the qualified life established for the equipment will not degrade safety systems equipment from its original design condition to the point where it cannot perform its required safety function(s), upon demand. The above requirement reflects the primary role of design qualification to provide reasonable assurance that design- and age-related common failure modes will not occur during performance of safety function(s) under postulated service conditions

Inelastic design of nuclear reactor structures and its implications on design of critical equipment

International Nuclear Information System (INIS)

Newmark, N.M.

1977-01-01

In considering the response of a nuclear reactor structure to seismic motions, one must take account of the implications of various levels of damage, short of impairment of safety, and definitely short of collapse, of the structure. Some structural elements of nuclear power plants must perforce remain elastic or nearly elastic in order to perform their allocated safety function. However, in many instances, a purely linear elastic analysis may be unreasonably conservative when one considers that even up to the near yield point range, there are nonlinearities of sufficient amount to reduce required design levels considerably. Moreover, limited yielding of a structure may reduce the response of equipment located in the structure below those levels of response that would be excited were the structure to remain elastic. Energy absorption in the inelastic range is most conveniently treated by use of the so-called 'ductility factor' introduced by the author for design of structures and equipment to resist explosion and blast forces. In general, for small excursions into the inelastic range, especially when the latter can be approximated by an elasto-plastic resistance curve, the design response spectrum is decreased by a simply determined factor that is related to the ductility factor. Many important parts of equipment of a nuclear power plant facility are attached to the principal parts of the structure and respond in a manner determined by the structural response as well as by the general ground motion to which the structure is subjected. This matter involves some difficulty in analysis, but appropriate calculational techniques and design methods are available. A suitable design simplification is one in which the response of the attachment is related to the modal responses of the structure. This equipment response is affected by the relative mass of the attachment and the structure

Preliminary design report for prototypical spent nuclear fuel rod consolidation equipment

International Nuclear Information System (INIS)

Judson, B.F.; Maillet, J.; O'Neill, G.L.; Tsitsichvili, J.; Tucoulat, D.

1986-12-01

The purpose of the Prototypical Consolidation Demonstration Project (PCDP) is to develop and demonstrate the equipment system that will be used to consolidate the bulk of the spent nuclear fuel generated in the United States prior to its placement in a geological repository. The equipment must thus be capable of operating on a routine production basis over a long period of time with stringent requirements for safety, reliability, productivity and cost-effectiveness. Four phases are planned for the PCDP. Phase 1 is the Preliminary Design of generic consolidation equipment that could be installed at a Monitored Retrievable Storage (MRS) facility or in the Receiving ampersand Handling Facility at a geologic repository site. Phase 2 will be the Final Design and preparation of procurement packages for the equipment in a configuration capable of being installed and tested in a special enclosure within the TAN Hot Shop at DOE's Idaho National Engineering Laboratory. In Phase 3 the equipment will be fabricated and then tested with mock fuel elements in a contractor's facility. Finally, in Phase 4 the equipment will be moved to the TAN facility for demonstration operation with irradiated spent fuel elements. 55 figs., 15 tabs

UOE Pipe Manufacturing Process Simulation: Equipment Designing and Construction

Science.gov (United States)

Delistoian, Dmitri; Chirchor, Mihael

2017-12-01

UOE pipe manufacturing process influence directly on pipeline resilience and operation capacity. At present most spreaded pipe manufacturing method is UOE. This method is based on cold forming. After each technological step appears a certain stress and strain level. For pipe stress strain study is designed and constructed special equipment that simulate entire technological process.UOE pipe equipment is dedicated for manufacturing of longitudinally submerged arc welded DN 400 (16 inch) steel pipe.

Advanced human-system interface design review guideline. Evaluation procedures and guidelines for human factors engineering reviews

Energy Technology Data Exchange (ETDEWEB)

O`Hara, J.M.; Brown, W.S. [Brookhaven National Lab., Upton, NY (United States); Baker, C.C.; Welch, D.L.; Granda, T.M.; Vingelis, P.J. [Carlow International Inc., Falls Church, VA (United States)

1994-07-01

Advanced control rooms will use advanced human-system interface (HSI) technologies that may have significant implications for plant safety in that they will affect the operator`s overall role in the system, the method of information presentation, and the ways in which operators interact with the system. The U.S. Nuclear Regulatory Commission (NRC) reviews the HSI aspects of control rooms to ensure that they are designed to good human factors engineering principles and that operator performance and reliability are appropriately supported to protect public health and safety. The principal guidance available to the NRC, however, was developed more than ten years ago, well before these technological changes. Accordingly, the human factors guidance needs to be updated to serve as the basis for NRC review of these advanced designs. The purpose of this project was to develop a general approach to advanced HSI review and the human factors guidelines to support. NRC safety reviews of advanced systems. This two-volume report provides the results of the project. Volume I describes the development of the Advanced HSI Design Review Guideline (DRG) including (1) its theoretical and technical foundation, (2) a general model for the review of advanced HSIs, (3) guideline development in both hard-copy and computer-based versions, and (4) the tests and evaluations performed to develop and validate the DRG. Volume I also includes a discussion of the gaps in available guidance and a methodology for addressing them. Volume 2 provides the guidelines to be used for advanced HSI review and the procedures for their use.

Advanced human-system interface design review guideline. Evaluation procedures and guidelines for human factors engineering reviews

International Nuclear Information System (INIS)

O'Hara, J.M.; Brown, W.S.; Baker, C.C.; Welch, D.L.; Granda, T.M.; Vingelis, P.J.

1994-07-01

Advanced control rooms will use advanced human-system interface (HSI) technologies that may have significant implications for plant safety in that they will affect the operator's overall role in the system, the method of information presentation, and the ways in which operators interact with the system. The U.S. Nuclear Regulatory Commission (NRC) reviews the HSI aspects of control rooms to ensure that they are designed to good human factors engineering principles and that operator performance and reliability are appropriately supported to protect public health and safety. The principal guidance available to the NRC, however, was developed more than ten years ago, well before these technological changes. Accordingly, the human factors guidance needs to be updated to serve as the basis for NRC review of these advanced designs. The purpose of this project was to develop a general approach to advanced HSI review and the human factors guidelines to support. NRC safety reviews of advanced systems. This two-volume report provides the results of the project. Volume I describes the development of the Advanced HSI Design Review Guideline (DRG) including (1) its theoretical and technical foundation, (2) a general model for the review of advanced HSIs, (3) guideline development in both hard-copy and computer-based versions, and (4) the tests and evaluations performed to develop and validate the DRG. Volume I also includes a discussion of the gaps in available guidance and a methodology for addressing them. Volume 2 provides the guidelines to be used for advanced HSI review and the procedures for their use

Conceptual design of a telecommunications equipment container for humanitarian logistics

Directory of Open Access Journals (Sweden)

Stella Parisi

2017-05-01

Full Text Available Preparedness addresses the strategy in disaster management that allows the implementation of successful operational response immediately after a disaster. With speed as the main driver, product design for humanitarian aid purposes is a key factor of success in situations of high uncertainty and urgency. Within this context, a telecommunications container (TC has been designed that belongs to a group of containers that serve the purpose of immediate response to global disasters. The TC includes all the necessary equipment to establish a telecommunication centre in the destroyed area within the first 72 hours of humanitarian operations. The design focuses on defining the topology of the various parts of equipment by taking into consideration factors of serviceability, functionality, human-product interaction, universal design language, energy consumption, sustainability and the interrelationship with the other containers. The concept parametric design has been implemented with SolidWorks® CAD system.

Designing a power supply for Nim-bin formatted equipment

International Nuclear Information System (INIS)

Banuelos G, L. E.; Hernandez D, V. M.; Vega C, H. R.

2016-09-01

From an old Nuclear Chicago power supply that was practically in the trash, was able to recover the 19 inches casing, rear connectors and the housing where the circuits were. From here all mechanical parts were cleaned and the electronic design was started to replace the original voltage and current functions of this equipment. The cards for the ±6, ±12 and ±24 voltages were designed, simulated and tested with circuitry that does not rely on specialized components or that is sold only by the equipment manufacturer. In the handling of the current by each voltage to operate, was possible to tie with the specifications of the manufacturers like Ortec or Canberra where a model of power supply gives a power of 160 Watts. Basic tests were performed to show that the behavior is very similar to commercial equipment; such as the full load regulation index and the noise level in the supply voltages. So our Nim-bin voltage source is viable for use in our institution laboratories. (Author)

Energy Design Guidelines for High Performance Schools: Tropical Island Climates

Energy Technology Data Exchange (ETDEWEB)

None

2004-11-01

Design guidelines outline high performance principles for the new or retrofit design of K-12 schools in tropical island climates. By incorporating energy improvements into construction or renovation plans, schools can reduce energy consumption and costs.

Tolerance-based Structural Design of Tubular-Structure Loading Equipments

Directory of Open Access Journals (Sweden)

Jiping Lu

2011-05-01

is worked out under different ball screws, trapezoidal screw threads, worm and worm gears. To meet the requirement of tolerance in tubular-structure assembly, mechanisms for all motions are defined. The design of loading equipment is tested and assessed by experiments, and the result shows the design is highly qualified for its assembly.

Revised guideline for the approval procedure of package designs in Germany

International Nuclear Information System (INIS)

Nitsche, F.; Roedel, R.

2004-01-01

The IAEA Regulations for the Safe Transport of Radioactive Material, TS-R-1 are applied in Germany through the implementation of the Dangerous Goods Transport Regulations for class 7 of the International Modal Organisations (ADR, RID, IMDG-Code, ICAO-TI). Based on this the approval procedures for packages designs applied in Germany are in compliance with the provisions of TS-R-1. The Guideline R 003 issued by the Ministry of Transport, Building and Housing (BMVBW) in 1991 is the basis for the package design approval procedures in Germany. This Guideline has been reviewed and revised to reflect latest developments in the regulations as well as in the regulatory practice. In particular it has been extended to the approval procedures of Type C packages, packages subject to transitional arrangements, special form and low dispersible radioactive material and provides more detailed information to the applicant about the requested documentation. Publication of this revised guideline has been delayed but it is expected to take place in October 2004. The paper gives an overview about the main parts and provisions of this revised Guideline R 003 with the focus on package design approval procedures

Design guidelines for audio presentation of graphs and tables

OpenAIRE

Brown, L.M.; Brewster, S.A.; Ramloll, S.A.; Burton, R.; Riedel, B.

2003-01-01

Audio can be used to make visualisations accessible to blind and visually impaired people. The MultiVis Project has carried out research into suitable methods for presenting graphs and tables to blind people through the use of both speech and non-speech audio. This paper presents guidelines extracted from this research. These guidelines will enable designers to implement visualisation systems for blind and visually impaired users, and will provide a framework for researchers wishing to invest...

A proposal to develop a high temperature structural design guideline for HTGR components

International Nuclear Information System (INIS)

Hada, K.

1989-01-01

This paper presents some proposals for developing a high-temperature structural design guideline for HTGR structural components. It is appropriate that a basis for developing high-temperature structural design rules is rested on well-established elevated-temperature design guidelines, if the same failure modes are expected for high-temperature components as considered in such design guidelines. As for the applicability of ASME B and PV Code Case N-47 to structural design rules for high-temperature components (service temperatures ≥ 900 deg. C), the following critical issues on material properties and service life evaluation rules have been pointed out. (i) no work-hardening of stress-strain curves at high temperatures due to dynamic recrystallization; (ii) issues relating to very significant creep; (iii) ductility loss after long-term ageing at high temperatures; (iv) validity of life-fraction rule (Robinson-Taira rule) as creep-fatigue damage evaluation rule. Furthermore, the validity of design margins of elevated-temperature structural design guidelines to high-temperature design rules should be clarified. Solutions and proposals to these issues are presented in this paper. Concerning no work-hardening due to dynamic recrystallization, it is shown that viscous effects cannot be neglected even at high extension rate for tensile tests, and that changes in viscous deformation rates by dynamic recrystallization should be taken into account. The extension rate for tensile tests is proposed to change at high temperatures. The solutions and proposals to the above-mentioned issues lead to the conclusion that the design methodologies of N-47 are basically applicable to the high-temperature structural design guideline for HTGR structural components in service at about 900 deg. C. (author). 9 refs, 5 figs

Aseismatic design of electrical equipments and instruments for nuclear power stations

International Nuclear Information System (INIS)

Suzuki, Yasuharu; Nishizawa, Kazuo; Miyazaki, Yoshio; Miura, Takumi

1977-01-01

The aseismatic design of electrical instruments is carried out according to IEEE Standard 344-1971 in the USA. In Japan also, the method of aseismatic design of electrical instruments has been investigated by the representatives of electric power companies and electric machine makers since 1972. In Hitachi Ltd., the statical method of confirming aseismatic property was established on the basis of the rigid design for electrical instruments. It is convenient to examine the aseismatic property of electrical equipments by classifying them into control and switch boards, electrical appliances, equipments and circuits. It is possible to use the static method treating earthquake force as static load by avoiding resonance with the electrical equipments which have the higher natural frequency than that of buildings. The purposes of the vibration test are to prove the validity of the theoretical analysis, to clarify the vibration characteristics, and to confirm the maintenance of functions and the strength of the equipments. The vibration tests of control boards, the switch boards of enclosed type, motor control centers, the racks for instrumentation, storage batteries and electrical appliances are explained. Moreover, the vibration analysis with a computer according to finite element method is described. (Kako, I.)

Sustainable design guidelines to support the Washington State ferries terminal design manual : stormwater and material issues.

Science.gov (United States)

2011-08-01

In an effort to assist the developers of the terminal design manual in potentially addressing : sustainable design issues, the overall goal is to produce Sustainable Design Guidelines that : will specifically address the unique needs and requirements...

Additional guideline for the design of BWR reload patterns

International Nuclear Information System (INIS)

Burte, D.P.

1990-01-01

The problems of the high magnitude of the reactivity worths of control rods/notches and the thermal shocks to fuel due to control rod withdrawals are considered in this paper. These problems are shown to be mitigated if in addition to complying with the traditional guidelines for designing fuel bundles and reload patterns the proposed additional guideline (in the form of the condition that the shape of the K∞ distribution remains constant throughout the cycle) is also complied with. It is argued that application of the additional guideline for operating conditions ensures that the core can operate with a constant power profile throughout the cycle without control rod movement. Fixed (integral or stand-alone) burnable poisons are thought to be useful in this regard. Some comments on how this may be attempted are included. Additional advantages resulting from the additional guideline are discussed. (author)

Designing electronic equipment on the basis of standard mechanical structures using internet re­sour­ces

Directory of Open Access Journals (Sweden)

Karlangach A. P.

2016-12-01

Full Text Available The author proposes a method to design electronic equipment based on functional-node design method that involves the use of 2D- and 3D- models mechanical structures for electronic equipment as a way to reduce development time and errors when creating design documentation for electronic equipment. At present, most areas of science and technology are computerized, more problems in designing electronic equipment are dealt with using computer-aided design (CAD and Computer-aided manufacturing (CAM to reduce the time required for development and manufacturing of electronic equipment. Development of design documentation also requires a more effective approach, because the less the time for development of the design documentation is, the faster the developed device will go into production. The aim of the study is to develop a method of designing electronic equipment using 2D and 3D models of standard mechanical structures for electronic equipment using Internet resources. Based on the presented methods is an example of designing a device from standard bearing structures. Compared with traditional technology, the method of designing electronic equipment using standard parts has the following advantages: - reduces time and improves quality of development through the use of existing design documentation; - accelerates the implementation and introducing into production processes; - increases unification of design solutions.

Rules and procedures for the design and operation of hazardous research equipment

International Nuclear Information System (INIS)

1978-12-01

The manual has been prepared for use by research personnel involved in experiments at the Lawrence Berkeley Laboratory. It contains rules and procedures for the design, test, installation, and operation of hazardous research equipment. Sect. I contains such information as responsibility of experimenters for safety, descriptions of the various Laboratory safety organizations, and enumeration of various services available to experimenters at the Laboratory. Sect. II describes specific rules for the setup and operation of experimental equipment at the Laboratory. Sect. III gives detailed design criteria and procedures for equipment frequently encountered in the high energy physics laboratory

Guidelines for the design of the working rules of the guarantee and quality control in radiotherapy commission

International Nuclear Information System (INIS)

Pardo, J.; Galmes, M.A.; Font, J.; Caro, J.; Serra, J.; Mata, F.; Bertan, S.; Biete, A.; Carceller, J.A.; Esco, R.; Palacios, A.; Veiras, C.; Vazquez, M.G.

2001-01-01

The 1566/1988 Royal Decree stated on July 17 th , focused on Quality Criteria in Radiation Therapy, was published in the Official Spanish Gazette on August 28 th . Its publication began a self-analysis process in all the Spanish Radiation Oncology Departments due to the fact that it implies the guidelines elaboration of each step of the radiation therapy process, including the patient post-treatment follow up and the equipment quality control. The Royal Decree orders the managers of the hospitals and facilities that have a radiation oncology department to create the Guarantee and Quality Control in Radiotherapy Commission. According to the Spanish law regulations, every single commission must have its own working rules based on the Chapter II, focused in 'Organos Colegiados', of the 30/1992 Law stated on November 27 th about Public Administration Legal Rules. The Guidelines for the design of the Guarantee and Quality Control in Radiotherapy Commission Working Rules here presented, have been done by consensus in Son Dureta University Hospital and afterwards sent to all Radiation Oncology Departments by the Spanish Society for Radiotherapy and Oncology. (author)

Introducing guidelines for eco-dynamic development and design

NARCIS (Netherlands)

Van Koningsveld, M.; Van Raalte, G.H.

2011-01-01

One of the key activities within the Building with Nature innovation programme is the development of a guideline for Eco-dynamic Development and Design. This guidance will be focussed on implementation of the Building with Nature principles throughout all of the stages of hydraulic engineering

Guidelines for the application of upper-room ultraviolet germicidal irradiation for preventing transmission of airborne contagion -- Part 2: Design and operation guidance

Energy Technology Data Exchange (ETDEWEB)

First, M.W.; Nardell, E.A.; Chaisson, W.; Riley, R.

1999-07-01

Installations of ultraviolet germicidal irradiation (UVGI) have been stimulated recently by a sudden rise in the incidence of tuberculosis. Hospitals, jails, and homeless shelters have been the most frequently equipped facilities because they are places where many tuberculosis cases are found, the buildings housing them tend to be old and not suited for economical increases in air exchange rates, and the work staffs have been apprehensive about transmission to themselves and their families. The diversity in structures currently being equipped with UVGI installations, plus the introduction of new designs of lamps and fixtures, have made it clear that an updated review of equipment performance factors and practical installation guidelines will be useful to interested parties. Illustrative examples are given of installations that have been made in a diverse set of facilities. In addition, representative figures are given to compare the cost of HVAC installations and UVGI installations that give an equivalent number of air changes based on equal levels of reduction in airborne microorganisms.

Design of equipment management information system for nuclear power plant

International Nuclear Information System (INIS)

Wang Chengyuan

1996-01-01

The author describes the ideas and practical method for need analysis, system function dividing, code design, program design and network disposition of equipment purchase management system of nuclear power plant during building, from the view of engineering investment control, schedule control and quality control

Guidelines for designing messages in risk communication

International Nuclear Information System (INIS)

Takashita, Hirofumi; Horikoshi, Hidehiko

2004-07-01

Risk Communication Study Team (hereafter called RC team) has designed messages for risk communication based on the analysis of the local residents' opinions which were expressed in several questionnaire surveys. The messages are described in a side format (Power Point format) every single content. This report provides basic guidelines for making messages that are used for risk communication, and does not include concrete messages which RC team designed. The RC team has already published the report entitled 'Information materials for risk communication' (JNC TN8450 2003-008) separately, and it gives the concrete messages. This report shows general cautions and checklists in designing messages, comments on the messages from outside risk communication experts, and opinions from local residents. (author)

DOE (Department of Energy) natural phenomena guidelines earthquake design and evaluation

International Nuclear Information System (INIS)

Short, S.A.; Murray, R.C.; Kennedy, R.P.

1989-01-01

Design and evaluation guidelines for DOE (Department of Energy) facilities subjected to earthquake, wind/tornado, and flood have been developed. This paper describes the philosophy and procedures fr the design or evaluation of facilities for earthquake ground shaking. The guidelines are intended to meet probabilistic-based performance goals expressed in terms of annual probability of exceedance of some level of structural damage. Meeting performance goals can be accomplished by specifying hazard probabilities of exceedance along with seismic behavior evaluation procedures in which the level of conservatism introduced is controlled such that desired performance can be achieved. Limited inelastic behavior is permitted by permitting demand determined from elastic response spectrum analyses to exceed capacity by an allowable inelastic demand-capacity ratio specified in the guidelines for different materials and construction

Communications of 30 November 1995 received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-19

The Director General has received notes verbales of 30 November 1995 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, the Republic of Korea, Luxembourg, The Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland and the United States of America relating to the export of nuclear material, equipment and technology. The purpose of the notes verbales is to provide further information on those Governments` Guidelines for transfers of nuclear-related dual-use equipment, material and related technology.

Communications of 30 November 1995 received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1996-01-01

The Director General has received notes verbales of 30 November 1995 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, the Republic of Korea, Luxembourg, The Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland and the United States of America relating to the export of nuclear material, equipment and technology. The purpose of the notes verbales is to provide further information on those Governments' Guidelines for transfers of nuclear-related dual-use equipment, material and related technology

Advanced Strategy Guideline. Air Distribution Basics and Duct Design

Energy Technology Data Exchange (ETDEWEB)

Arlan Burdick

2011-12-01

This report discusses considerations for designing an air distribution system for an energy efficient house that requires less air volume to condition the space. Considering the HVAC system early in the design process will allow adequate space for equipment and ductwork and can result in cost savings.

Equipment design for reliability testing of protection system

International Nuclear Information System (INIS)

Situmorang, Johnny; Tjahjono, H.; Santosa, A. Z.; Tjahjani, S.DT.; Ismu, P.H; Haryanto, D.; Mulyanto, D.; Kusmono, S

1999-01-01

The equipment for reliability testing of cable of protection system has been designed as a a furnace with the electric heater have a 4 kW power, and need time 10 minute to reach the designed maximum temperature 3000C. The dimension of furnace is 800 mm diameter and 2000 mm length is isolated use rockwool isolator and coated by aluminium. For the designed maximum temperature the surface temperature is 78 0c. Assemble of specimens is arranged horizontally in the furnace. The failure criteria will be defined based on the behaviour of the load circuit in each line of cable specimens

Korean Society of Cardiovascular Imaging Guidelines for Cardiac Computed Tomography

International Nuclear Information System (INIS)

Kim, Young Jin; Choi, Byoung Wook; Choe, Kyu Ok; Yong, Hwan Seok; Kim, Yang Min; Choe, Yeon Hyeon; Lim, Tae Hwan; Park, Jae Hyung

2011-01-01

The Korean Society of Cardiovascular Imaging (KOCSI) has issued a guideline for the use of cardiac CT imaging in order to assist clinicians and patients in providing adequate level of medical service. In order to establish a guideline founded on evidence based medicine, it was designed based on comprehensive data such as questionnaires conducted in international and domestic hospitals, intensive journal reviews, and with experts in cardiac radiology. The recommendations of this guideline should not be used as an absolute standard and medical professionals can always refer to methods non-adherent to this guideline when it is considered more reasonable and beneficial to an individual patient's medical situation. The guideline has its limitation and should be revised appropriately with the advancement medical equipment technology and public health care system. The guideline should not be served as a measure for standard of care. KOCSI strongly disapproves the use of the guideline to be used as the standard of expected practice in medical litigation processes.

Outline of the seismic design guideline of an FBR - a tentative draft

International Nuclear Information System (INIS)

Akiyama, Hiroshi; Ohtsubo, Hideomi; Nakamura, Hideharu; Matsuura, Shinichi; Hagiwara, Yutaka; Yuhara, Tetsuo; Hirayama, Hiroshi; Kokubo, Kunio; Ooka, Yuji.

1993-01-01

Central Research Institute of Electric Power Industry (Japan) is carrying out the Demonstration Test and Research Program of Buckling of FBR (FY 1987-FY 1993). The first half of the research program was finished after establishing a seismic buckling design guideline (a tentative draft). The purpose of this paper is to describe the dynamic buckling characteristics of FBR main vessels and the outline of the rationalized buckling design guideline for seismic loadings. (orig.)

Guideline to good practices for control and calibration of measuring and test equipment (M ampersand TE) at DOE nuclear facilities

International Nuclear Information System (INIS)

1993-03-01

The purpose of the Guideline to Good Practices for Control and Calibration of Measuring and Test Equipment (M ampersand TE) at DOE Nuclear Facilities is to provide contractor maintenance organizations with information that may be used for the development and implementation of a rigorously controlled maintenance program directed at controlling and calibrating M ampersand TE used for maintenance tasks at DOE nuclear facilities. This document is intended to be an example guideline for the implementation of DOE Order 4330.4A, Maintenance Management Program, Chapter II, Element 11. DOE contractors should not feel obligated to adopt all parts of this guide. Rather, they should use the information contained herein as a guide for developing an M ampersand TE program applicable to their facility

How to Design and Equip a Mentalization-Based Play Therapy Room.

Science.gov (United States)

Rüth, Ulrich; Holch, Astrid

2018-01-01

Designing and equipping a play therapy room as a differentiated tool in a psychodynamic approach to child psychotherapy is seldom discussed. This article sketches out the equipment and furnishing of a play therapy room to be used for mentalization-based psychodynamic psychotherapy and gives examples of the use of such a room in practice.

Design review report for modifications to RMCS safety class equipment

International Nuclear Information System (INIS)

Corbett, J.E.

1997-01-01

This report documents the completion of the formal design review for modifications to the Rotary Mode Core Sampling (RMCS) safety class equipment. These modifications are intended to support core sampling operations in waste tanks requiring flammable gas controls. The objective of this review was to approve the Engineering Change Notices affecting safety class equipment used in the RMCS system. The conclusion reached by the review committee was that these changes are acceptable

Design review report for modifications to RMCS safety class equipment

Energy Technology Data Exchange (ETDEWEB)

Corbett, J.E.

1997-05-30

This report documents the completion of the formal design review for modifications to the Rotary Mode Core Sampling (RMCS) safety class equipment. These modifications are intended to support core sampling operations in waste tanks requiring flammable gas controls. The objective of this review was to approve the Engineering Change Notices affecting safety class equipment used in the RMCS system. The conclusion reached by the review committee was that these changes are acceptable.

Design of mobile receiving and treatment equipment for radioactive liquid waste

International Nuclear Information System (INIS)

Kong Jinsong; Guo Weiqun; Lu Jingbin

2012-01-01

The advantage and disadvantage of radioactive liquid waste treatment technology are analyzed in this paper. The experimental disposal equipment for radioactive liquid waste with complicated sources is designed by combining the far infrared calcification technology with evaporation technology. It has advantages of low energy consuming and high decontamination efficiency. The frothy and dirt appear rarely in this equipment. (authors)

Assessment of EPRI water chemistry guidelines for new nuclear power plants

International Nuclear Information System (INIS)

Reid Richard; Kim Karen; McCree, Anisa; Eaker, Richard; Sawochka, Steve; Giannelli, Joe

2012-09-01

Water chemistry control technologies for nuclear power plants have been significantly enhanced over the past few decades to improve material and equipment reliability and fuel performance, and to minimize radionuclide production and transport. Chemistry Guidelines have been developed by the Electric Power Research Institute (EPRI) for currently operating plants and have been intermittently revised over the past twenty-five years for the protection of systems and components and for radiation management. As new plants are being designed for improved safety and increased power production, it is important to ensure that the designs consider implementation of state-of-the-art, industry developed water chemistry controls. In parallel, the industry will need to consider and update water chemistry guidelines as well as plant startup and operational strategies based on the advanced plant designs. EPRI has performed assessments of water chemistry control guidance or assumptions provided in design and licensing documents for several advanced plant designs. These designs include: Westinghouse AP1000 Pressurized Water Reactor AREVA US-EPR Pressurized Water Reactor Mitsubishi Nuclear Energy Systems/Mitsubishi Heavy Industries Advanced Pressurized Water Reactor Korea Hydro and Nuclear Power APR1400 Pressurized Water Reactor Toshiba Advanced Boiling Water Reactor (ABWR) General Electric-Hitachi Economic Simplified Boiling Water Reactor (ESBWR) The intent of these assessments was to identify key design differences in each of the new plant designs relative to the current operating fleet and to identify differences in water chemistry specifications or design assumptions provided in design and licensing documents for the plants in comparison to current EPRI Water Chemistry Guidelines. This paper provides a summary of the key results of these assessments. The fundamental design and operation of the advanced plants is similar to the currently operating fleet. As such, the new plants are

ITER physics design guidelines: 1989

International Nuclear Information System (INIS)

Uckan, N.A.

1990-01-01

The physics basis for ITER has been developed from an assessment of the results of the last twenty-five years of tokamak research and from detailed analysis of important physics issues specifically for the ITER design. This assessment has been carried out with direct participation of members of the experimental teams of each of the major tokamaks in the world fusion program through participation in ITER workshops, contributions to the ITER Physics R and D Program, and by direct contacts between the ITER team and the cognizant experimentalists. Extrapolations to the present data base, where needed, are made in the most cautious way consistent with engineering constraints and performance goals of the ITER. In cases where a working assumptions had to be introduced, which is insufficiently supported by the present data base, is explicitly stated. While a strong emphasis has been placed on the physics credibility of the design, the guidelines also take into account that ITER should be designed to be able to take advantage of potential improvements in tokamak physics that may occur before and during the operation of ITER. (author). 33 refs

Human-centered design of the human-system interfaces of medical equipment: thyroid uptake system

International Nuclear Information System (INIS)

Monteiro, Jonathan K.R.; Farias, Marcos S.; Santos, Isaac J.A. Luquetti; Monteiro, Beany G.

2013-01-01

Technology plays an important role in modern medical centers, making healthcare increasingly complex, relying on complex technical equipment. This technical complexity is particularly noticeable in the nuclear medicine. Poorly design human-system interfaces can increase the risks for human error. The human-centered approach emphasizes the development of the equipment with a deep understanding of the users activities, current work practices, needs and abilities of the users. An important concept of human-centered design is that the ease-of-use of the equipment can be ensured only if users are actively incorporated in all phases of the life cycle of design process. Representative groups of users are exposed to the equipment at various stages in development, in a variety of testing, evaluation and interviewing situations. The users feedback obtained is then used to refine the design, with the result serving as input to the next interaction of design process. The limits of the approach are that the users cannot address any particular future needs without prior experience or knowledge about the equipment operation. The aim of this paper is to present a methodological framework that contributes to the design of the human-system interfaces, through an approach related to the users and their activities. A case study is described in which the methodological framework is being applied in development of new human-system interfaces of the thyroid uptake system. (author)

Human-system interface design review guideline -- Reviewer`s checklist: Final report. Revision 1, Volume 2

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

NUREG-0700, Revision 1, provides human factors engineering (HFE) guidance to the US Nuclear Regulatory Commission staff for its: (1) review of the human system interface (HSI) design submittals prepared by licensees or applications for a license or design certification of commercial nuclear power plants, and (2) performance of HSI reviews that could be undertaken as part of an inspection or other type of regulatory review involving HSI design or incidents involving human performance. The guidance consists of a review process and HFE guidelines. The document describes those aspects of the HSI design review process that are important to the identification and resolution of human engineering discrepancies that could adversely affect plant safety. Guidance is provided that could be used by the staff to review an applicant`s HSI design review process or to guide the development of an HSI design review plan, e.g., as part of an inspection activity. The document also provides detailed HFE guidelines for the assessment of HSI design implementations. NUREG-0700, Revision 1, consists of three stand-alone volumes. Volume 2 is a complete set of the guidelines contained in Volume 1, Part 2, but in a checklist format that can be used by reviewers to assemble sets of individual guidelines for use in specific design reviews. The checklist provides space for reviewers to enter guidelines evaluations and comments.

Equipment Specific Optimum Blast-Design Using Genetic Algorithm

Directory of Open Access Journals (Sweden)

Rahul Upadhyay

2015-08-01

Full Text Available Design of blasting parameters plays an important role in the optimization of mining cost as well as cost of subsequent processing of ore. Drilling and handling costs are the major mining cost. This work presents an indirect optimization model for mining cost through optimization of blasting parameters for a particular set of drilling and loading equipment.

Designing equipment for use in gamma radiation environments

International Nuclear Information System (INIS)

Vandergriff, K.U.

1990-05-01

High levels of gamma radiation are known to cause degradation in a variety of materials and components. When designing systems to operate in a high radiation environment, special precautions and procedures should be followed. This report (1) outlines steps that should be followed in designing equipment and (2) explains the general effects of radiation on various engineering materials and components. Much information exists in the literature on radiation effects upon materials. However, very little information is available to give the designer a step-by-step process for designing systems that will be subject to high levels of gamma radiation, such as those found in a nuclear fuel reprocessing facility. In this report, many radiation effect references are relied upon to aid in the design of components and systems. 11 refs., 4 tabs

Designing, Developing, and Implementing Diversity Training: Guidelines for Practitioners.

Science.gov (United States)

Kincaid, Tanna M.; Horner, Erin R.

1997-01-01

Discusses diversity in the workplace and offers guidelines for practitioners in designing, developing, and implementing diversity training. Highlights include linking the diversity initiative to the organization's mission, cultural climate assessments, reviewing policies and procedures, needs assessment, learner analysis, establishing objectives,…

Stiffness Parameter Design of Suspension Element of Under-Chassis-Equipment for A Rail Vehicle

Science.gov (United States)

Ma, Menglin; Wang, Chengqiang; Deng, Hai

2017-06-01

According to the frequency configuration requirements of the vibration of railway under-chassis-equipment, the three- dimension stiffness of the suspension elements of under-chassis-equipment is designed based on the static principle and dynamics principle. The design results of the concrete engineering case show that, compared with the design method based on the static principle, the three- dimension stiffness of the suspension elements designed by the dynamic principle design method is more uniform. The frequency and decoupling degree analysis show that the calculation frequency of under-chassis-equipment under the two design methods is basically the same as the predetermined frequency. Compared with the design method based on the static principle, the design method based on the dynamic principle is adopted. The decoupling degree can be kept high, and the coupling vibration of the corresponding vibration mode can be reduced effectively, which can effectively reduce the fatigue damage of the key parts of the hanging element.

The design and qualification of radiation tolerant equipment for the nuclear power industry

International Nuclear Information System (INIS)

Sharp, R.; Pater, L.

1995-01-01

The nuclear power industry has many demands for equipment tolerant to the damaging effects of radiation. The wide variety of applications, including components handling, tooling, monitoring and communications, means that a systematic evaluation of the effects of radiation on materials and components used for equipment in radioactive facilities is often required. This paper describes the various effects of radiation on equipment, and discusses how to manage them when using and designing equipment. (Author)

Guidelines for planning and design of mobile radiological units

Energy Technology Data Exchange (ETDEWEB)

Schelenz, R [Federal Office for Environmental Radioactivity in Food, Total Diet and Infant Food, Federal Research Centre for Nutrition, Karlsruhe (Germany)

1995-07-01

A significant number of mobile radiological units are in operation worldwide aiming to provide reliable radiological data. They mainly have been designed and constructed on a national basis according to the particular needs and commitments of the specific laboratory or country. In most cases, these units are intended to be used in emergency situations for in-situ radiological measurements of accidentally released radioactivity, sometimes for monitoring environmental pollution. As the purpose of these units is very diversified in regard to the kind of vehicle and its in-built measuring equipment the varying outfit of these units cannot be adopted in general for other countries aiming to improve their capability for in-situ radiological measurement. In order to achieve harmonization of equipment and comparability of radiological data being obtained from field measurements it is necessary to have general guidelines available for designing mobile radiological units taking into account different sceneries and tasks to be achieved. In the very early stages of an accident most of the information available on the quantity of radioactive material being released, its radionuclide composition and the likely progression of the accident will come from the operator, and will be based on the conditions in the plant. Few environmental monitoring results from off-side can be expected within the first few hours. In this very early phase, decisions on the application of protective measures will therefore, be based largely on plant status and forecasts of changes in that status as well as on meteorological data. As time progresses, results will increasingly become available from the monitoring of radionuclides in the environment (e.g. dose rates and concentration of radionuclides in air and particular materials such as water, food etc). Monitoring results can be used to estimate potential doses to people and the need for further protective measures can thus be determined from a

Guidelines for planning and design of mobile radiological units

International Nuclear Information System (INIS)

Schelenz, R.

1995-01-01

A significant number of mobile radiological units are in operation worldwide aiming to provide reliable radiological data. They mainly have been designed and constructed on a national basis according to the particular needs and commitments of the specific laboratory or country. In most cases, these units are intended to be used in emergency situations for in-situ radiological measurements of accidentally released radioactivity, sometimes for monitoring environmental pollution. As the purpose of these units is very diversified in regard to the kind of vehicle and its in-built measuring equipment the varying outfit of these units cannot be adopted in general for other countries aiming to improve their capability for in-situ radiological measurement. In order to achieve harmonization of equipment and comparability of radiological data being obtained from field measurements it is necessary to have general guidelines available for designing mobile radiological units taking into account different sceneries and tasks to be achieved. In the very early stages of an accident most of the information available on the quantity of radioactive material being released, its radionuclide composition and the likely progression of the accident will come from the operator, and will be based on the conditions in the plant. Few environmental monitoring results from off-side can be expected within the first few hours. In this very early phase, decisions on the application of protective measures will therefore, be based largely on plant status and forecasts of changes in that status as well as on meteorological data. As time progresses, results will increasingly become available from the monitoring of radionuclides in the environment (e.g. dose rates and concentration of radionuclides in air and particular materials such as water, food etc). Monitoring results can be used to estimate potential doses to people and the need for further protective measures can thus be determined from a

Designing radiation protection signs

International Nuclear Information System (INIS)

Rodriguez, M.A.; Richey, C.L.

1995-01-01

Entry into hazardous areas without the proper protective equipment is extremely dangerous and must be prevented whenever possible. Current postings of radiological hazards at the Rocky Flats Environmental Technology Site (RFETS) do not incorporate recent findings concerning effective warning presentation. Warning information should be highly visible, quickly, and easily understood. While continuing to comply with industry standards (e.g., Department of Energy (DOE) guidelines), these findings can be incorporated into existing radiological sign design, making them more effective in terms of usability and compliance. Suggestions are provided for designing more effective postings within stated guidelines

Guidelines for CubeSat's Thermal Design

Science.gov (United States)

Rodriguez-Ruiz, Juan; Patel, Deepak

2015-01-01

Thermal and Fluids Analysis Workshop 2015, Silver Spring, MD. NCTS 19104-15. What does it take to thermally designlow cost, low mass cubesats? What are the differences in the approach when you compare with large scale missions?What additional risk is acceptable? What is the approach to hardware? How is the testing campaign run? These aresome of the questions that will be addressed in this course, which is designed to equip the attendees to support thedevelopment of cubesats at their organization.

Studies for aseismatic design of atomic power equipment

International Nuclear Information System (INIS)

Uchiyama, Yuichi; Takayanagi, Masaaki; Moriyama, Takeo; Mizuno, Sadao

1976-01-01

The social requirements for the safety of nuclear power stations are very severe, and especially in Japan where earthquakes occur frequently, the safety against earthquakes is regarded as an important matter. The numerous machinery and equipments composing nuclear power plants have largely different roles in the safety, accordingly it is important to maintain effectively the safety as a whole. The design is carried out by classifying buildings, machinery and equipments, pipings and electric appliances according to the importance, and so that the aseismatic property corresponding to the importance is given to each. In most cases, the aseismatic design is carried out with computing codes, but it is necessary to forward the design by proving the propriety of analysis models and calculated results. Efforts are exerted in Hitachi Ltd. to improve the accuracy of the aseismatic analysis by carrying out basic experiment, the demonstration test in actual plants and the study on analytical method as many as possible. The measurement of the vibration of actual pipings in order to confirm the supporting conditions, the comparison of multi-input analysis and SRSS method for piping analysis, and the vibration tests of a model containment vessel and a fuel assembly were carried out, and the results are reported in this paper. It is important to improve the accuracy of earthquake response analysis further. (Kako, I.)

Design/Operations review of core sampling trucks and associated equipment

International Nuclear Information System (INIS)

Shrivastava, H.P.

1996-01-01

A systematic review of the design and operations of the core sampling trucks was commissioned by Characterization Equipment Engineering of the Westinghouse Hanford Company in October 1995. The review team reviewed the design documents, specifications, operating procedure, training manuals and safety analysis reports. The review process, findings and corrective actions are summarized in this supporting document

ALS beamline design requirements: A guide for beamline designers

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-06-01

This manual is written as a guide for researchers in designing beamlines and endstations acceptable for use at the ALS. It contains guidelines and policies related to personnel safety and equipment and vacuum protection. All equipment and procedures must ultimately satisfy the safety requirements set aside in the Lawrence Berkeley National Laboratory (LBNL) Health and Safety Manual (PUB-3000) which is available from the ALS User Office or on the World WideWeb from the LBNL Homepage (http:// www.lbl.gov).

Strategy Guideline. Compact Air Distribution Systems

Energy Technology Data Exchange (ETDEWEB)

Burdick, Arlan [IBACOS, Inc., Pittsburgh, PA (United States)

2013-06-01

This guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

Acoustical Design Guidelines for Living Rooms for Adults with intellectual Disabilities

NARCIS (Netherlands)

Saher, K.

2013-01-01

The aim of this thesis is to investigate the effects of building design tools on acoustical quality parameters in living rooms for adults with intellectual disabilities (ID) and develop acoustical design guidelines for architects. This study is specifically concerned with the validation of

Application of core structural design guidelines in conceptual fuel pin design

International Nuclear Information System (INIS)

Patel, M.R.; Stephen, J.D.

1979-01-01

The paper describes an application of the Draft RDT Standards F9-7, -8, and -9 to conceptual design of Fast Breeder Reactor (FBR) fuel pins. The Standards are being developed to provide guidelines for structural analysis and design of the FBR core components which have limited ductility at high fluences and are not addressed by the prevalent codes. The development is guided by a national working group sponsored by the Division of Reactor Researcch and Technology of the Department of Energy. The development program summarized in the paper includes establishment of design margins consistent with the test data and component performance requirements, and application of the design rules in various design activities. The application program insures that the quantities required for proper application of the design rules are available from the analysis methods and test data, and that the use of the same design rules in different analysis tools used at different stages of a component design producees consistent results. This is illustrated in the paper by application of the design rules in the analysis methods developed for conceptual and more detailed designs of an FBR fuel pin

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

2000-01-01

The document reproduces the text of the Notes Verbales dated 1 February 2000 received by the Director General of the IAEA from the Resident Representatives to the Agency of Argentina, Austria, Belgium, Bulgaria, Brazil, Canada, the Czech Republic, Germany, Hungary, Ireland, Italy, Japan, Republic of Korea, Latvia, the Netherlands, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Switzerland, Ukraine, the United Kingdom and the United States relating to export of nuclear material, equipment and technology. The purpose of the notes verbale is to provide further information on those Governments' Guidelines for Nuclear Transfers. The attachment to these Notes Verbales is also included

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-15

The document reproduces the text of the Notes Verbales dated 1 February 2000 received by the Director General of the IAEA from the Resident Representatives to the Agency of Argentina, Austria, Belgium, Bulgaria, Brazil, Canada, the Czech Republic, Germany, Hungary, Ireland, Italy, Japan, Republic of Korea, Latvia, the Netherlands, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Switzerland, Ukraine, the United Kingdom and the United States relating to export of nuclear material, equipment and technology. The purpose of the notes verbale is to provide further information on those Governments' Guidelines for Nuclear Transfers. The attachment to these Notes Verbales is also included.

Communications received from certain member states regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1992-07-01

The document reproduces the text of the notes verbales dated 1 June 1992, received by the Director General from the Resident Representatives to the Agency of Australia, Austria, Belgium, Bulgaria, Canada, Czech and Slovak Federal Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, japan, Luxembourg, Netherlands, Norway, Poland, Portugal, Romania, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland and the United States of America relating to the export of nuclear material, equipment for technology. The purpose of these notes verbales is to clarify parts of the Trigger List incorporated in the Annex A to the Guidelines for Nuclear Transfer. 1 tab

Review of revised Japanese seismic guidelines for Nuclear Power Plant design

International Nuclear Information System (INIS)

Kato, M.

1987-01-01

Development of aseismic design for nuclear power plants in Japan has evolved roughly in three stages. The first phase, which continued by 1978, was a period progressive development when design for each siteplant has referred to designs of predecessor plants and have added the latest knowledge and experience in that time. The second phase from issuance of 'Regulatory Guide for Aseismic Design of Nuclear Power Reactor Facilities' (1978, revised in 1981), or 1978 to 1986, was a period when the application of customary conservative design method was continued, while standardization of the aseismic design technology have been proceded. It is in this phase when new knowledge was accumulated by aseismic proof studies. The third phase represents a transient period to rational design when the conservative aseismic design technology has been reviewed due to the new knowledge and revision of the above JEAG guideline has progressed for incorporation in design, and ont the other hand by-laws of the Ministry of International Trade and Industry are being provided. In this report a review is given of aseismic design and its guideline after the second phase onward and an overview of the revised JEAG - Recent Aseismic Design Method - and the by-laws including rationalization of aseismic design technology

Designing with the mind in mind simple guide to understanding user interface design guidelines

CERN Document Server

Johnson, Jeff

2014-01-01

In this completely updated and revised edition of Designing with the Mind in Mind, Jeff Johnson provides you with just enough background in perceptual and cognitive psychology that user interface (UI) design guidelines make intuitive sense rather than being just a list or rules to follow. Early UI practitioners were trained in cognitive psychology, and developed UI design rules based on it. But as the field has evolved since the first edition of this book, designers enter the field from many disciplines. Practitioners today have enough experience in UI design that they have been exposed to

APSIC guidelines for disinfection and sterilization of instruments in health care facilities

Directory of Open Access Journals (Sweden)

Moi Lin Ling

2018-02-01

Full Text Available Abstract Background The Asia Pacific Society of Infection Control launched its revised Guidelines for Disinfection and Sterilization of Instruments in Health Care Facilities in February 2017. This document describes the guidelines and recommendations for the reprocessing of instruments in healthcare setting. It aims to highlight practical recommendations in a concise format designed to assist healthcare facilities at Asia Pacific region in achieving high standards in sterilization and disinfection. Method The guidelines were revised by an appointed workgroup comprising experts in the Asia Pacific region, following reviews of previously published guidelines and recommendations relevant to each section. Results It recommends the centralization of reprocessing, training of all staff with annual competency assessment, verification of cleaning, continual monitoring of reprocessing procedures to ensure their quality and a corporate strategy for dealing with single-use and single-patient use medical equipment/devices. Detailed recommendations are also given with respect to reprocessing of endoscopes. Close working with the Infection Prevention & Control department is also recommended where decisions related to reprocessing medical equipment/devices are to be made. Conclusions Sterilization facilities should aim for excellence in practices as this is part of patient safety. The guidelines that come with a checklist help service providers identify gaps for improvement to reach this goal.

Ergonomics standards and guidelines for computer workstation design and the impact on users' health - a review.

Science.gov (United States)

Woo, E H C; White, P; Lai, C W K

2016-03-01

This paper presents an overview of global ergonomics standards and guidelines for design of computer workstations, with particular focus on their inconsistency and associated health risk impact. Overall, considerable disagreements were found in the design specifications of computer workstations globally, particularly in relation to the results from previous ergonomics research and the outcomes from current ergonomics standards and guidelines. To cope with the rapid advancement in computer technology, this article provides justifications and suggestions for modifications in the current ergonomics standards and guidelines for the design of computer workstations. Practitioner Summary: A research gap exists in ergonomics standards and guidelines for computer workstations. We explore the validity and generalisability of ergonomics recommendations by comparing previous ergonomics research through to recommendations and outcomes from current ergonomics standards and guidelines.

Evaluation of Design Models of Process Equipment for Use in PRIDE: Remote Operability and Maintainability

International Nuclear Information System (INIS)

Kim, Ki Ho; Kim, Sung Hyun; Yu, Seung Nam; Lee, Jong Kwang; Park, Byung Suk; Han, Jong Hui; Cho, Il Je; Lee, Han Soo

2012-01-01

Process equipment for pyroprocessing are being developed at KAERI (Korea Atomic Energy Research Institute). Those equipment should be operated and maintained in a fully remote manner in the argon gas filled cell of PRIDE (PyRoprocess Integrated inactive DEmonstration facility) at KAERI because direct human access to the in-cell is not possible during an operation due to the high toxicity of the argon gas. To make such process equipment remotely operable and maintainable, their design developments have been tested and evaluated in a simulator before they are constructed. A simulator as a means of evaluating the remote operability and maintainability of the design models of process equipment for pyroprocessing is described, and results of the design models tested and evaluated in a simulator are presented

Analysis of QA audit checklist for equipment suppliers

International Nuclear Information System (INIS)

Tian Xuehang

2012-01-01

Eleven aspects during the equipment manufacturing by the suppliers, including the guidelines and objectives of quality assurance, management department review, document and record control, staffing and training, design control, procurement control, control of items, process control, inspection and testing control, non-conformance control, and internal and external QA audit, are analyzed in this article. The detailed QA audit checklist on these above mentioned aspects are described and the problems found in real QA audit are listed in this article. (authors)

Design guides for radioactive-material-handling facilities and equipment

International Nuclear Information System (INIS)

Doman, D.R.; Barker, R.E.

1980-01-01

Fourteen key areas relating to facilities and equipment for handling radioactive materials involved in examination, reprocessing, fusion fuel handling and remote maintenance have been defined and writing groups established to prepare design guides for each areas. The guides will give guidance applicable to design, construction, operation, maintenance and safety, together with examples and checklists. Each guide will be reviewed by an independent review group. The guides are expected to be compiled and published as a single document

REQUIREMENTS FOR DESIGN, EQUIPMENT AND OPERATION MODE OF TAXI VEHICLES

Directory of Open Access Journals (Sweden)

Norayr Oganesovich Bludyan

2015-09-01

Full Text Available The analysis of international experience in application of requirements for the taxi vehicles design and equipment. The approaches to improvement of cabbing have been defined by determination of requirements for taxi vehicles.

Sound & Vibration 20 Design Guidelines for Health Care Facilities

CERN Document Server

Tocci, Gregory; Cavanaugh, William

2013-01-01

Sound, vibration, noise and privacy have significant impacts on health and performance. As a result, they are recognized as essential components of effective health care environments. However, acoustics has only recently become a prominent consideration in the design, construction, and operation of healthcare facilities owing to the absence, prior to 2010, of clear and objective guidance based on research and best practices. Sound & Vibration 2.0 is the first publication to comprehensively address this need. Sound & Vibration 2.0 is the sole reference standard for acoustics in health care facilities and is recognized by: the 2010 FGI Guidelines for the Design and Construction of Health Care Facilities (used in 60 countries); the US Green Building Council’s LEED for Health Care (used in 87 countries); The Green Guide for Health Care V2.2; and the International Code Council (2011). Sound & Vibration 2.0 was commissioned by the Facility Guidelines Institute in 2005, written by the Health Care Acous...

Guidelines for determining design basis ground motions

International Nuclear Information System (INIS)

1993-11-01

This report develops and applies a method for estimating strong earthquake ground motion. The emphasis of this study is on ground motion estimation in Eastern North America (east of the Rocky Mountains), with particular emphasis on the Eastern United States and southeastern Canada. Specifically considered are ground motions resulting from earthquakes with magnitudes from 5 to 8, fault distances from 0 to 500 km, and frequencies from 1 to 35 Hz. The two main objectives were: (1) to develop generic relations for estimating ground motion appropriate for site screening; and (2) to develop a guideline for conducting a thorough site investigation needed to define the seismic design basis. For the first objective, an engineering model was developed to predict the expected ground motion on rock sites, with an additional set of amplification factors to account for the response of the soil column over rock at soil sites. The results incorporate best estimates of ground motion as well as the randomness and uncertainty associated with those estimates. For the second objective, guidelines were developed for gathering geotechnical information at a site and using this information in calculating site response. As a part of this development, an extensive set of geotechnical and seismic investigations was conducted at three reference sites. Together, the engineering model and guidelines provide the means to select and assess the seismic suitability of a site

Play for All Guidelines: Planning, Design and Management of Outdoor Play Settings for All Children. Second Edition.

Science.gov (United States)

Moore, Robin C., Ed.; Goltsman, Susan M., Ed.; Iacofano, Daniel S., Ed.

These guidelines assist professional designers, park and recreation managers, and community groups when making decisions about the planning, design, and ongoing management of children's public play environments. The guidelines are updated to meet or exceed the requirements of the Americans with Disabilities Act Guidelines (July 26, 1991) and the…

Design and implementation of equipment for monitoring the salinity in the subsoil

Directory of Open Access Journals (Sweden)

Mariano Norzagaray Campos

2012-09-01

Full Text Available Geochemical exploration equipments to explore the contaminants and structures geological in the subsoil come from abroad are expensive and sometimes parts for replacement are not available in the market. So it is necessary design apparatus that meet cover these needs. To the monitoring of variations in salinity there is semi-automatic equipment, but it always has difficult to manage. However, is not equipment for the indirect study of salinity in the subsoil. In this work was design equipment for measurement the apparent resistivity in the subsoil, at same time allow know the salinity, as well as the detection of any pollutant in groundwater. For make it, was selected a design of earthing systems, with electronic hardware which were jointed for apply to subsoil a direct current (DC through an array dipole-dipole and vertical electric sounding, with brass and stainless steel electrodes. In the earthing systems the electrodes were collocated in the equidistant line between the detectors of potential and current. A geometric factor (K, that depend on theelectrodes distance and direct current (I injected in the electrodes A and B, was used for measure the potential difference between the electrodes M and N; after was calculate the resistivity point to point for obtain a subsoil tomography geoelectrical. The equipment was calibrated with minimum error (rms < 2% whit respect to curves obtained in similar commercial equipment. On this situation, in this work was modernized and automated an equipment to determine thesalinity of the subsoil. The instrument was tasted in the micro basin Texcoco, State of Mexico, to define the environment geometry formed by alluvial or lake sediments from igneous rocks (andesites, rhyolites and tuffs vitreous or “tepetates” which by its mineralogical composition allowed to the lateral resistivity be associate with free components trace from the aquifer: Cd, Cu, Cr, Co, Ni, Pb or Zn and others. This method constitutes

Development of new canine and feline preventive healthcare guidelines designed to improve pet health.

Science.gov (United States)

2011-01-01

The American Veterinary Medical Association (AVMA) and American Animal Hospital Association (AAHA) have jointly introduced the first Canine and Feline Preventive Healthcare Guidelines. These consensus statements provide veterinarians with a new resource for improving patient care by emphasizing the value and scope of regular pet examinations. The two guidelines provide complete recommendations for comprehensive preventive healthcare programs, published as accessible, single-page documents. The guidelines are based on the subjective-objective-assessment-plan (SOAP) methodology of case management, a proven approach traditionally used with sick or injured patients. This logical and disciplined process is equally applicable to healthy patients and is designed to consistently deliver optimal patient care. The guidelines recommend visits for health examinations on at least an annual basis, recognizing that for many pets, more frequent visits may be appropriate, depending on the individual needs of the patient. The guidelines also provide detailed diagnostic, therapeutic, prevention, and follow up plans, to be accompanied by appropriate documentation. The inclusive content and concise format of the guidelines are designed to maximize their practical value and make them easy to implement.

Organizational Design within University Extension Units: Some Concepts, Options, and Guidelines

Science.gov (United States)

Baker, Harold R.

1976-01-01

Drawing on the behavioral sciences, the author outlines alternative modes of structuring and organizing an extension unit. The advantages and disadvantages of several organizational design options, the purposes and management of the temporary task force, and some general guidelines for making organizational design decisions are discussed.…

Design scheme of automatic feeding equipment of domestic uranium chemical concentrate

International Nuclear Information System (INIS)

Hu Jinming; Wang Chao; Peng Jinhui; Zhang Libo

2014-01-01

In order to solve problems by artificial feeding mode with low work efficiency, large intensity manual labor and environmental pollution in domestic uranium concentrate purification process, the design scheme of automatic feeding device was set up, including work flow sheet, composition of automatic equipment and operation. By application of automatic feeding equipment, the feeding speed can be greatly increased, labor force can be reduced, and harm to workman health can be decreased. (authors)

Development of floor design response spectra for seismic design of floor-supported equipment or components, Revision 1, February 1978

International Nuclear Information System (INIS)

Anon.

1979-01-01

This guide presents an acceptable method for developing two horizontal and one vertical floor design response spectra at various floor or other equipment-support locations from the time-history motions resulting from the dynamic analysis of the supporting structure. These floor design response spectra are used in the dynamic analysis of systems or equipment supported at various locations of the supporting structure. Consulation has been provided by the Advisory Committee on Reactor Safeguards

Design considerations, tooling, and equipment for remote in-service inspection of radioactive piping and pressure-vessel systems

International Nuclear Information System (INIS)

Swannack, D.L.; Schmoker, D.S.

1983-01-01

This paper summarizes results obtained in use of remotely-operated nondestructive testing (NDT) equipment for inspection of reactor-system components. Experience obtained in operating the Fast Flux Test Facility (FFTF) has provided a basis for field verification of remote NDT equipment designs and has suggested development improvements. Remote Viewing and data gathering systems used include periscopes, borescopes, fiberscopes, hybrid borescopes/fiberscopes, and closed circuit television. A summary of design consideration for inspection equipment and power plant design is presented to achieve improved equipment operation and reduction of plant maintenance downtime

Conceptual design of the alcohol waste treatment equipment

International Nuclear Information System (INIS)

Fujisawa, Morio; Nitta, Kazuhiko; Morita, Yasuhiro; Nakada, Eiju

2001-01-01

This report describes the result of Conceptual Design of the Alcohol Waste Treatment Equipment. The experimental fast Reactor, JOYO, saves the radioactive alcohol waste at storage tank. As this alcohol waste is not able to treat with existing equipment, it is stored about 5 m 3 . And the amount of this is increasing every year. So it is necessary to treat the alcohol waste by chemical resolution for example. On account of this, the investigative test about filtration and dialyzer, and conceptual design about catalyst oxidation process, which is composed from head end process to resolution, are done. The results of investigation show as follows. 1. Investigative Test about filtration and dialyzer. (1) The electric conduction is suitable for the judgement of alkyl sodium hydrolysis Alkyl sodium hydrolysis is completed below 39% alcohol concentration. (2) The microfiltration is likely to separate the solid in alcohol waste. (3) From laboratory test, the electrodialyzer is effective for sodium separation in alcohol waste. And sodium remove rate, 96-99%, is confirmed. 2. Conceptual Design. The candidate process is as follows. (1) The head end process is electrodialyzer, and chemical resolution process is catalyst oxidation. (2) The head end process is not installed, and chemical resolution process is catalyst oxidation. (3) The head end process is electrodialyzer, and alcohol extracted by pervaporation. In this Conceptual Design, as far these process, the components, treatment ability, properties of waste, chemical mass balance, safety for fire and explosion, and the plot plan are investigated. As a result, remodeling the existing facility into catalyst oxidation process is effective to treat the alcohol waste, and treatment ability is about 1.25 l/h. (author)

Improving the hygienic design of closed equipment

DEFF Research Database (Denmark)

Friis, Alan; Jensen, Bo Boye Busk

2005-01-01

Maintenance of proper hygiene in closed process equipment is in many ways a complex task. The interaction between the physical design and the nature of fluid flow is of main concern. During cleaning the main performance of the flow is to bring cleaning agents in the right doses to all parts of th...... computational fluid dynamics models to be able to predict the cleaning efficiency in especially complex parts of process plants has excellent potentials for desktop improvements and computer pre-validation of the hygienic performance of process plants....

Some difference of concepts between design guideline for FBR base isolation system and aseismic design guideline of LWR in Japan

International Nuclear Information System (INIS)

Shibata, Heki

1992-01-01

This paper deals with the concept and the relation of 'the Base Isolation System and FBR' to the Safety Criteria and the Guideline of the Aseismic Design of LWR in Japan. The Central Research Institute of Electric Power Industries have been working for FBR last several years. The author has been contribute to their works, and this is one of the subjects. He described his own idea obtained through the cooperative work with CRIEPI. (author)

Designing usable web forms- Empirical evaluation of web form improvement guidelines

DEFF Research Database (Denmark)

Seckler, Mirjam; Heinz, Silvia; Bargas-Avila, Javier A.

2014-01-01

This study reports a controlled eye tracking experiment (N = 65) that shows the combined effectiveness of 20 guidelines to improve interactive online forms when applied to forms found on real company websites. Results indicate that improved web forms lead to faster completion times, fewer form...... submission trials, and fewer eye movements. Data from subjective questionnaires and interviews further show increased user satisfaction. Overall, our findings highlight the importance for web designers to improve their web forms using UX guidelines....

The design and equipments of hospital pharmacies in Isfahan, Iran

Directory of Open Access Journals (Sweden)

Ali Mohammad Sabzghabaee

2010-01-01

Full Text Available Background: Nowadays pharmaceutical care departments located in hospitals are amongst the important pillars of the healthcare system. The aim of this study was to evaluate designing features and equipments of hospital drugstores affiliated with Isfahan University of Medical Sciences. Methods: In this cross-sectional study a self-defined and validated questionnaire was used which included all the necessary and standard needed spaces and equipments of an ideal hospital pharmacy. The questionnaire was filled in by one of the researchers in all twelve hospital drugstores located in the teaching and non-teaching hospitals affiliated with Isfahan University of Medical Sciences. Data analysis was done using SPSS (version 14. Results: Results showed that 56% of drugstore space allocations were unsuitable. Used pharmaceutical equipments in 75% of surveyed hospitals were not according to the standards. Almost all of these pharmacies had rather an enough space for storage, but cold storages were not designed in 58% of them. In 66% of perused hospitals, pharmaceutical services disposal level was admissible. The structural engineering parameters like size and dimensions, available spaces, availability of structural planes, existence of air conditioning systems and brightness controllers, adequate stores for drugs and safe places for narcotics were observed in 55% of pharmacies. Conclusions: There are apparent out of standard space allocations and shortages of needed equipments for offering drug services in studied drugstores that may probably lead to a waste of time and money. These issues may reduce the efficiency and safety of pharmaceutical services and drug administration in hospitals.

Guidelines for the structural design of experimental multi-purpose VHTR at the elevated temperature services

International Nuclear Information System (INIS)

Nomura, Sueo; Uga, Takeo; Miyamoto, Yoshiaki; Muto, Yasushi; Ikushima, Takeshi

1976-02-01

The guidelines are presented for structural design of the experimental multi-purpose VHTR(Very High Temperature Reactor) at the elevated temperature services. Covered are features of the VHTR structural design, specifications, safety design, seismic design, failure modes to be considered, stress criteria for various load combinations and the mechanical properties of the materials. The guidelines were prepared by referring to safety criteria of high-temperature gas cooled reactors, ASME Boiler and Pressure Vessel code, Section III, case 1592 and the domestic seismic design guide of nuclear power facilities. (auth.)

41 CFR 109-38.502 - Guidelines.

Science.gov (United States)

2010-07-01

... 41 Public Contracts and Property Management 3 2010-07-01 2010-07-01 false Guidelines. 109-38.502 Section 109-38.502 Public Contracts and Property Management Federal Property Management Regulations System... 38-MOTOR EQUIPMENT MANAGEMENT 38.5-Scheduled Maintenance § 109-38.502 Guidelines. ...

Guidelines for design and development of computer/microprocessor based systems in research and power reactors

International Nuclear Information System (INIS)

Dhodapkar, S.D.; Chandra, A.K.

1993-01-01

Computer systems are being used in Indian research reactors and nuclear power plants in the areas of data acquisition, process monitoring and control, alarm annunciation and safety. The design and evaluation of these systems requires a special approach particularly due to the unique nature of the software which is an essential constituent of these systems. It was decided to evolve guidelines for designing and review of computer/microprocessor based systems for use in nuclear power plants in India. The present document tries to address various issues and presents guidelines which are as comprehensive as possible and cover all issues relating to the design and development of computer based systems. These guidelines are expected to be useful to the specifiers, designers and reviewers of such systems. (author). 6 refs., 1 fig

Design Guidelines for Collaboration and Participation with Examples from the LN4LD (Learning Network for Learning Design)

NARCIS (Netherlands)

Burgos, Daniel; Hummel, Hans; Tattersall, Colin; Brouns, Francis; Koper, Rob

2007-01-01

Burgos, D., Hummel, H. G. K., Tattersall, C., Brouns, F., & Koper, R. (2009). Design Guidelines for Collaboration and Participation with Examples from the LN4LD (Learning Network for Learning Design). In L. Lockyer, S. Bennett, S. Agostinho & B. Harper (Eds.), Handbook of Research on Learning Design

Cryogenic Safety Rules and Guidelines at CERN

CERN Multimedia

CERN. Geneva

2016-01-01

CERN defines and implements a Safety Policy that sets out the general principles governing safety at CERN. As an intergovernmental organisation, CERN further establishes its own Safety Rules as necessary for its proper functioning. In this process, it takes into account the laws and regulation of the Host States (France and Switzerland), EU regulations and directives, as well as international regulations, standards and directives. For the safety of cryogenic equipment, this is primarily covered by the Safety Regulation for Mechanical Equipment and the General Safety Instruction for Cryogenic Equipment. In addition, CERN has also developed Safety Guidelines to support the implementation of these safety rules, covering cryogenic equipment and oxygen deficiency hazard assessment and mitigation. An overview of the cryogenic safety rules and these safety guidelines will be presented.

Generation of equipment response spectrum considering equipment-structure interaction

International Nuclear Information System (INIS)

Lee, Sang Hoon; Yoo, Kwang Hoon

2005-01-01

Floor response spectra for dynamic response of subsystem such as equipment, or piping in nuclear power plant are usually generated without considering dynamic interaction between main structure and subsystem. Since the dynamic structural response generally has the narrow-banded shapes, the resulting floor response spectra developed for various locations in the structure usually have high spectral peak amplitudes in the narrow frequency bands corresponding to the natural frequencies of the structural system. The application of such spectra for design of subsystems often leads to excessive design conservatisms, especially when the equipment frequency and structure are at resonance condition. Thus, in order to provide a rational and realistic design input for dynamic analysis and design of equipment, dynamic equipment-structure interaction (ESI) should be considered in developing equipment response spectrum which is particularly important for equipment at the resonance condition. Many analytical methods have been proposed in the past for developing equipment response spectra considering ESI. However, most of these methods have not been adapted to the practical applications because of either the complexities or the lack of rigorousness of the methods. At one hand, mass ratio among the equipment and structure was used as an important parameter to obtain equipment response spectra. Similarly, Tseng has also proposed the analytical method for developing equipment response spectra using mass ratio in the frequency domain. This method is analytically rigorous and can be easily validated. It is based on the dynamic substructuring method as applied to the dynamic soil-structure interaction (SSI) analysis, and can relatively easily be implemented for practical applications without to change the current dynamic analysis and design practice for subsystems. The equipment response spectra derived in this study are also based on Tseng's proposed method

Deriving guidelines for the design of plate evaporators in heat pumps using zeotropic mixtures

DEFF Research Database (Denmark)

Mancini, Roberta; Zühlsdorf, Benjamin; Jensen, Jonas Kjær

2018-01-01

This paper presents a derivation of design guidelines for plate heat exchangers used for evaporation of zeotropic mixtures in heat pumps. A mapping of combined heat exchanger and cycle calculations for different combinations of geometrical parameters and working fluids allowed estimating the trade....... It was found that the pressure drop limit leading to infeasible designs was dependent on the working fluid, thereby making it impossible to define a guideline based on maximum allowable pressure drops. It was found that economically feasible designs could be obtained by correlating the vapour Reynolds number...

Injury survey of a non-traditional 'soft-edged' trampoline designed to lower equipment hazards.

Science.gov (United States)

Eager, David B; Scarrott, Carl; Nixon, Jim; Alexander, Keith

2013-01-01

In Australia trampolines contribute one quarter of all childhood play equipment injuries. The objective of this study was to gather and evaluate injury data from a non-traditional, 'soft-edged', consumer trampoline, where the design aimed to minimise injuries from the equipment and from falling off. The manufacturer of the non-traditional trampoline provided the University of Technology Sydney with their Australian customer database. The study involved surveys in Queensland and New South Wales, between May 2007 and March 2010. Initially injury data was gathered by a phone interview pilot study, then in the full study, through an email survey. The 3817 respondents were the carers of child users of the 'soft-edge' trampolines. Responses were compared with Australian and US emergency department data. In both countries the proportion of injuries caused by the equipment and falling off was compared with the proportion caused by the jumpers to themselves or each other. The comparisons showed a significantly lower proportion resulted from falling-off or hitting the equipment for this design when compared to traditional trampolines, both in Australia and the US. This research concludes that equipment-induced and falling-off injuries, the more severe injuries on traditional trampolines, can be significantly reduced with appropriate trampoline design.

Agile Contracts: Designing an Agile Team Selection Guideline

DEFF Research Database (Denmark)

Pries-Heje, Lene; Pries-Heje, Jan

2014-01-01

with “endless” re-negotiation of the requirements; you need a more flexible way to develop IS. A new way of coping with many changes is to use an agile development approach and a fixed budget and resources contract. This paper presents an example case. We analyse the case and design a guideline for how......When you have stable and non-ambiguous requirements then a classic contract for IS between a supplier and a public sector institution based on a requirements specification may be well suited. However, if you have to accept many changes or have ambiguous requirements then you may end up...... to implement a fixed budget and resources contract in the public sector. The guideline includes elements to cope with challenges in a tender process such as transparency, criteria for supplier selection, and live assessment of resource skills and capabilities, as well as achieving the flexibility for change...

US Department of Energy natural phenomena design/evaluation guidelines/lessons learned

International Nuclear Information System (INIS)

Conrads, T.J.

1991-08-01

In the spring of 1988, DOE Order 6430.1A, General Design Criteria [1], was issued for use. This document references UCRL-15910, Design and Evaluation Guidelines for DOE Facilities Subjected to Natural Phenomena Hazards [2], which is to be used as the basis for the design and evaluation of new and existing facilities to natural phenomena loading. Rather than use the historical deterministic methods for computing structural and component loading from potential natural phenomena, UCRL-15910 incorporated the years of hazards studies conducted throughout the US Department of Energy complex into probabilistic-based methods. This paper describes the process used to incorporate US Department of Energy natural phenomena design guidelines into the Hanford Plant Standards -- Standard Design Criteria for Architectural and Civil Standards [3]. It also addresses the subsequent use of these criteria during structural assessments of facilities, systems, and components of various vintage in support of updating safety analysis reports. The paper includes comparison of results using these most recent probabilistic-based natural phenomena loading criteria to those obtained from previous assessments, and it addresses the lessons learned from the many structural evaluations of 1940--1960 vintage buildings

Advanced control room design review guidelines: Merging old and new

International Nuclear Information System (INIS)

Carter, R.J.; Wachtel, J.A.

1992-01-01

The nuclear power industry is currently developing operator interface systems based on innovative applications of digital computers. To assure that this advanced technology is incorporated in a way that maximizes the potential safety benefits of the technology and minimizes the potential negative effects on human performance, human factors principles must be considered. NUREG-0700 contains guidelines for the review of operator interfaces. However, in light of the rapid technological advances in digital technology which have taken place in the eleven years since its publication, it is no longer adequate to assess the rapidly changing human-system interfaces. A research program, the purpose of which is to upgrade NUREG-0700, has been initiated. Thus far a set of draft advanced control room design review (ACRDR) guidelines has been complied. Three tasks, which were oriented towards integrating the applicable guidelines in NUREG-0700 into the ACRDR document, are described in the paper

Design and Manufacturing of Composite Tower Structure for Wind Turbine Equipment

Science.gov (United States)

Park, Hyunbum

2018-02-01

This study proposes the composite tower design process for large wind turbine equipment. In this work, structural design of tower and analysis using finite element method was performed. After structural design, prototype blade manufacturing and test was performed. The used material is a glass fiber and epoxy resin composite. And also, sand was used in the middle part. The optimized structural design and analysis was performed. The parameter for optimized structural design is weight reduction and safety of structure. Finally, structure of tower will be confirmed by structural test.

System design and equipment reliability for wide web working at Hem Heath Colliery

Energy Technology Data Exchange (ETDEWEB)

Hall, L

1982-02-01

This paper outlines the challenge to mining engineers on system design and reliability of equipment and how Hem Heath Colliery in the UK, is meeting this challenge, by describing current systems of work and equipment on the faces, summarising experience gained with succeeding faces, the results achieved, and posing considerations for the future.

Design of free-space optical transmission system in computer tomography equipment

Science.gov (United States)

Liu, Min; Fu, Weiwei; Zhang, Tao

2018-04-01

Traditional computer tomography (CT) based on capacitive coupling cannot satisfy the high data rate transmission requirement. We design and experimentally demonstrate a free-space optical transmission system for CT equipment at a data rate of 10 Gb / s. Two interchangeable sections of 12 pieces of fiber with equal length is fabricated and tested by our designed laser phase distance measurement system. By locating the 12 collimators in the edge of the circle wheel evenly, the optical propagation characteristics for the 12 wired and wireless paths are similar, which can satisfy the requirement of high-speed CT transmission system. After bit error rate (BER) measurement in several conditions, the BER performances are below the value of 10 - 11, which has the potential in the future application scenario of CT equipment.

NATO ARI on Ergonomic Data for Equipment Design

CERN Document Server

1984-01-01

For many years ergonomists and human engineering specialists have made significant contributions to the solution of problems faced in the area of human labour and to the introduction of their research results and field experience into the process of equipment design. However, the rapid increase in complexity of equipment in use as well as in development demonstrates the necessity of broaden­ ing the point of view continuously. The workshop held in Munich from March 22nd to March 26th, 1982, was an excellent opportunity for the participants to discuss their respective interests and their interpretation of needs for future research. The workshop was sponsored by the Human Factors Special Programme Panel of the Scientific Affairs Division of NATO. This sponsorship, together with the helpful assistance rendered by Drs. Bayraktar, Kroemer, and Sanders, is gratefully acknowledged. This volume contains the papers presented during the workshop. All these papers are directly related to the general aim: the ex­ chang...

In-service inspection guidelines for composite aerospace structures

International Nuclear Information System (INIS)

Heida, Jaap H.; Platenkamp, Derk J.

2012-01-01

The in-service inspection of composite aerospace structures is reviewed, using the results of a evaluation of promising, mobile non-destructive inspection (NDI) methods. The evaluation made use of carbon fibre reinforced specimens representative for primary composite aerospace structures, including relevant damage types such as impact damage, delaminations and disbonds. A range of NDI methods were evaluated such as visual inspection, vibration analysis, phased array ultrasonic inspection, shearography and thermography inspection. Important aspects of the evaluation were the capability for defect detection and characterization, portability of equipment, field of view, couplant requirements, speed of inspection, level of training required and the cost of equipment. The paper reviews the damage tolerance design approach for composites, and concludes with guidelines for the in-service inspection of composite aerospace structures.

Communications received from certain Member States regarding guidelines for transfers of nuclear-related dual-use equipment, materials, software and related technology

International Nuclear Information System (INIS)

2005-01-01

The Director General of the International Atomic Energy Agency has received Notes Verbales dated 25 October 2004 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Brazil, Canada, Cyprus, Czech Republic, Estonia, Finland, France, Greece, Hungary, Italy, Japan, Malta, Netherlands, Norway, Republic of Korea, South Africa, Spain, Sweden, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland and the United States of America, relating to transfers of nuclear-related dual-use equipment, materials, software and related technology. The purpose of the Notes Verbales is to provide further information on those Governments' guidelines for transfers of nuclear-related dual-use equipment, materials, software and related technology. In the light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to these Notes Verbales is also reproduced in full

Communications received from certain Member States regarding guidelines for transfers of nuclear-related dual-use equipment, materials, software and related technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-02-23

The Director General of the International Atomic Energy Agency has received Notes Verbales dated 25 October 2004 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Brazil, Canada, Cyprus, Czech Republic, Estonia, Finland, France, Greece, Hungary, Italy, Japan, Malta, Netherlands, Norway, Republic of Korea, South Africa, Spain, Sweden, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland and the United States of America, relating to transfers of nuclear-related dual-use equipment, materials, software and related technology. The purpose of the Notes Verbales is to provide further information on those Governments' guidelines for transfers of nuclear-related dual-use equipment, materials, software and related technology. In the light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to these Notes Verbales is also reproduced in full.

Philosophy for seismic design of nuclear power plants

International Nuclear Information System (INIS)

Teramae, Tetsuo

1981-01-01

In Japan, earthquakes occur frequently, therefore the basic philosophy in the aseismatic design of nuclear facilities is to design so as not to cause the accident which gives to the public in the surroundings and the employes radiation injuries in the case of large earthquakes. The ''Guideline for the aseismatic design techniques for nuclear power stations'' was drawn up in 1970 as the result of studies by related government offices and organizations. The guideline for determining the earthquakes used for design was published later, and the allowable stress for equipments and pipings has been adopted in accordance with ASME Code, Section 3. The buildings and structures, equipments and pipings in nuclear facilities are classified into three classes according to their importance in aseismatic design. The power of design earthquakes is determined corresponding to the degree of importance. The determination of the standard earthquake waves is explained. The proprieth of aseismatic design is evaluated on the basis of the basic concept of the combination of loads and the allowable limit. The static analysis in accordance with the Building Standards Act is applied to the B and C classes, while the dynamic analysis is required for the A class. The aseismatic analysis of buildings and structures, equipments and pipings is outlined. Many problems to be solved still remain though the concept of aseismatic design has been clarified. (Kako, I.)

Absolute air filtering equipment in the nuclear industrie. Design - Safety - Experience

International Nuclear Information System (INIS)

Lucas, J.C.

1977-01-01

The problems encountered in the design of absolute filters (HEPA FILTERS) are presented: glass-fibre filter papers; standards and characteristics: efficiency, fire-resistance, humidity-resistance, radiation-resistance, etc; various types of paper folding: deep folds and small folds, dihedrally mounted; filtering elements; designs; characteristics and quality control; The design of filtration equipment is also analysed: mounting in metal or concrete casings. French and American designs (Regulatory Guide 1-52); and gas-tight casings allowing contaminated filters to be renewed without breaking the gas-tight seal

An investigation into the Eco-design of Energy Using Products directive.

Science.gov (United States)

Meech, Christina Goodrick

2006-01-01

This study reviews the eco-design of energy using products directive and additional legislation on the way that waste electrical and electronic equipment should be disposed of, and how this may influence the future product design of appliances. During the investigation 'lifecycle analysis' and consumers' responses to this legislation, and the industry were also reviewed. Finally, for future product designers who work with electrical and electronic equipment some guidelines and rules are given to consider while designing for the environment and sustainability.

Preliminary design report: Prototypical Spent Fuel Consolidation Equipment Demonstration Project: Phase 1

International Nuclear Information System (INIS)

Blissell, W.H.; Ciez, A.P.; Mitchell, J.L.; Winkler, C.J.

1986-12-01

This document describes the Westinghouse Preliminary Design for the Prototypical Consolidation Demonstration Project per Department of Energy (DOE) Contract No. DE-AC07-86ID12649 and under direction of the DOE Idaho Operations Office. The preliminary design is the first step to providing the Department of Energy with a fully qualified, licensable, cost-effective spent fuel rod consolidation system. The design was developed using proven technologies and equipment to create an innovative approach to previous rod consolidation concepts. These innovations will better enable the Westinghouse system to: consolidate fuel rods in a precise, fully-controlled, accountable manner; package all rods from two PWR fuel assemblies or from four BWR fuel assemblies in one 8.5 inch square consolidated rods canister; meet all functional requirements; operate with all fuel types common to the US commercial nuclear industry with minimal tooling changeouts; and meet consolidation production process rates, while maintaining operator and public health and safety. This Preliminary Design Report provides both detailed descriptions of the equipment required to perform the rod consolidation process and the supporting analyses to validate the design

Designing efficient logging systems for northern hardwoods using equipment production capabilities and costs.

Science.gov (United States)

R.B. Gardner

1966-01-01

Describes a typical logging system used in the Lake and Northeastern States, discusses each step in the operation, and presents a simple method for designing and efficient logging system for such an operation. Points out that a system should always be built around the key piece of equipment, which is usually the skidder. Specific equipment types and their production...

Design guideline to prevent the pipe rupture by radiolysis gases in BWR steam piping

International Nuclear Information System (INIS)

Inagaki, T.; Miyagawa, M.; Ota, T.; Sato, T.; Sakata, K.

2009-01-01

In late 2001, pipe rupture accidents due to fast combustion of radiolysis gas occurred in Japan and elsewhere's BWR power plants. TENPES began to set up the guideline as action to such a new problem to prevent accumulation and combustion of radiolysis gas in BWR steam piping. And then, the first edition of guideline was published in October 2005. Afterwards, the experimental study about combustion/detonation of radiolysis gas have been continued. And in March 2007, TENPES published a revised edition of the guideline. This is the report of the revised edition of that guideline. According to this guideline, it became possible to design BWR's steam piping to prevent accumulation of radiolysis gas. (author)

Advanced Strategy Guideline: Air Distribution Basics and Duct Design

Energy Technology Data Exchange (ETDEWEB)

Burdick, A.

2011-12-01

This report discusses considerations for designing an air distribution system for an energy efficient house that requires less air volume to condition the space. Considering the HVAC system early in the design process will allow adequate space for equipment and ductwork and can result in cost savings. Principles discussed that will maximize occupant comfort include delivery of the proper amount of conditioned air for appropriate temperature mixing and uniformity without drafts, minimization of system noise, the impacts of pressure loss, efficient return air duct design, and supply air outlet placement, as well as duct layout, materials, and sizing.

Cost analysis guidelines

International Nuclear Information System (INIS)

Strait, R.S.

1996-01-01

The first phase of the Depleted Uranium Hexafluoride Management Program (Program)--management strategy selection--consists of several program elements: Technology Assessment, Engineering Analysis, Cost Analysis, and preparation of an Environmental Impact Statement (EIS). Cost Analysis will estimate the life-cycle costs associated with each of the long-term management strategy alternatives for depleted uranium hexafluoride (UF6). The scope of Cost Analysis will include all major expenditures, from the planning and design stages through decontamination and decommissioning. The costs will be estimated at a scoping or preconceptual design level and are intended to assist decision makers in comparing alternatives for further consideration. They will not be absolute costs or bid-document costs. The purpose of the Cost Analysis Guidelines is to establish a consistent approach to analyzing of cost alternatives for managing Department of Energy's (DOE's) stocks of depleted uranium hexafluoride (DUF6). The component modules that make up the DUF6 management program differ substantially in operational maintenance, process-options, requirements for R and D, equipment, facilities, regulatory compliance, (O and M), and operations risk. To facilitate a consistent and equitable comparison of costs, the guidelines offer common definitions, assumptions or basis, and limitations integrated with a standard approach to the analysis. Further, the goal is to evaluate total net life-cycle costs and display them in a way that gives DOE the capability to evaluate a variety of overall DUF6 management strategies, including commercial potential. The cost estimates reflect the preconceptual level of the designs. They will be appropriate for distinguishing among management strategies

Radiology preparedness in ebola virus disease: guidelines and challenges for disinfection of medical imaging equipment for the protection of staff and patients.

Science.gov (United States)

Mollura, Daniel J; Palmore, Tara N; Folio, Les R; Bluemke, David A

2015-05-01

The overlap of early Ebola virus disease (EVD) symptoms (eg, fever, headache, abdominal pain, diarrhea, emesis, and fatigue) with symptoms of other more common travel-related diseases (eg, malaria, typhoid fever, pneumonia, and meningococcemia) may result in delayed diagnosis of EVD before isolation of infected patients. Radiology departments should consider policies for and approaches to decontamination of expensive and potentially easily damaged radiology equipment. In addition, the protection of radiology personnel must be considered during the work-up phase of undiagnosed EVD patients presenting to emergency departments. The purpose of this article is to consider the effect of EVD on radiology departments and imaging equipment, with particular consideration of guidelines currently available from the Centers for Disease Control and Prevention that may be applicable to radiology. (©) RSNA, 2015.

Design for a Remote Monitoring Equipment of Krypton-85

Institute of Scientific and Technical Information of China (English)

LUXue-sheng; LIUGuo-rong; YEFeng; JINHui-min; TANGPei-jia

2003-01-01

A prototype equipment for monitoring Krypton-85 in situ is designed and set up. A series of relevant software is also developed for remote control, data acquirement and data analysis. Weight of the system is about 300 kg, which is composed of NaI(T1) detector, digi DART, Marillin measurement container and lead shield. The whole system is placed on a homemade go-cart.

Recommendations to ASME for code guidelines and criteria for continued operation of equipment

International Nuclear Information System (INIS)

Harvey, J.F.

1993-01-01

In May 1988, the American Society of Mechanical Engineers, ASME, asked the Pressure Vessel Research Council, PVRC, to review the part it should play in the continued operation of equipment originally designed and fabricated to the ASME codes and rules. This was prompted solely by an economic opportunity in which the capital expenditures to replace plants was far more costly than evaluating, repairing, and extending the nominal design life of the individual component. For instance, nuclear plants are normally designed for a life of 40 years, while fossil fired facilities may have been designed for other time lives, yet at the end of their original design life may actually have many useful years remaining. While this action was economically prompted, it inherently involved a two-fold one; namely, (1) safety, (2) legal. There is no question of safety to operating personnel. While codes for fossil components do not specify design lives, their adoption by many states provides a legal means of procedure in event of a mishap. This recognizes a cradle-to-grave safety responsibility. It is toward maintaining ASMEs leadership as a code authority that this report has been prepared

The basic discussion on nuclear power safety improvement based on nuclear equipment design

International Nuclear Information System (INIS)

Zhao Feiyun; Yao Yangui; Yu Hao; He Yinbiao; Gao Lei; Yao Weida

2013-01-01

The safety of strengthening nuclear power design was described based on nuclear equipment design after Fukushima nuclear accident. From these aspects, such as advanced standard system, advanced design method, suitable test means, consideration of beyond design basis event, and nuclear safety culture construction, the importance of nuclear safety improvement was emphatically presented. The enlightenment was given to nuclear power designer. (authors)

Survey of injury sources for a trampoline with equipment hazards designed out.

Science.gov (United States)

Eager, David; Scarrott, Carl; Nixon, Jim; Alexander, Keith

2012-07-01

In Australia, trampolines contribute approximately one-quarter of all childhood play-equipment injuries. The purpose of this study was to gather and evaluate injury data from a nontraditional, 'soft-edged', consumer trampoline in which the equipment injury sources have been designed out. A survey was undertaken in Queensland and New South Wales. The manufacturer of the nontraditional trampoline provided the University of Technology, Sydney, with their Australian customer database. Injury data were gathered in a pilot study by phone interview, then in a full study through an email survey. Results from 3817 respondents were compared with earlier Australian and US data from traditional trampolines gathered from emergency departments.   A significantly lower proportion of the injuries caused by falling off or striking the equipment was found for this new design when compared with traditional trampolines both in Australia and in the USA. The age of children being injured on trampolines in Australia was found to be markedly lower than in North America. This research indicates that with appropriate design the more severe injuries on traditional trampolines can be significantly reduced. © 2012 The Authors. Journal of Paediatrics and Child Health © 2012 Paediatrics and Child Health Division (Royal Australasian College of Physicians).

Design of equipment used for high-level waste vitrification at the West Valley Demonstration Project

International Nuclear Information System (INIS)

Vance, R.F.; Brill, B.A.; Carl, D.E.

1997-06-01

The equipment as designed, started, and operated for high-level radioactive waste vitrification at the West Valley Demonstration Project in western New York State is described. Equipment for the processes of melter feed make-up, vitrification, canister handling, and off-gas treatment are included. For each item of equipment the functional requirements, process description, and hardware descriptions are presented

NASA preferred reliability-practices for design and test

Science.gov (United States)

Lisk, Ronald C.

1992-01-01

NASA HQ established the NASA R&M Steering Committee (R&MSC) comprised of membership from each NASA field center. The primary charter of the R&MSC is to obtain, record, and share the best design practices that NASA has applied to successful space flight programs and current design considerations (guidelines) that should enhance flight reliability on emerging programs. The practices and guidelines are being assembled in a living document for distribution to NASA centers and the aerospace community. The document will be updated annually with additional practices and guidelines as contributions from the centers are reviewed and approved by the R&MSC. Practices and guidelines are not requirements, but rather a means of sharing procedures and techniques that a given center and the R&MSC together feel have strong technical merit and application to the design of space-related equipment.

Underwater fuel handling equipment maintenance. Verification of design assumptions, specific problems and tools, case study

International Nuclear Information System (INIS)

Kurek, J.B.

1995-01-01

The majority of CANDU Fuel Transfer System equipment at Pickering is located under fourteen feet of water, as dictated by the containment and shielding requirements. Such arrangement, however, creates specific problems with equipment maintenance. Each single piece of equipment serves two generating units, which means in case of defect- double losses on production, or two units shut down simultaneously for planned maintenance. The requirement for underwater maintenance was not anticipated at the design stage, which multiples the level of difficulty, and creates requirement for developing special tools for each work. Removal of the damaged fuel from the receiving bays and decontamination of submerged equipment is also part of the problem. The purpose of this presentation is to share our experience with the designers, operators, maintenance mechanics and technical personnel of the other CANDU generating stations

Implementation of seismic design and evaluation guidelines for the Department of Energy high-level waste storage tanks and appurtenances

International Nuclear Information System (INIS)

Conrads, T.J.

1993-06-01

In the fall of 1992, a draft of the Seismic Design and Evaluation Guidelines for the Department of Energy (DOE) High-level Waste Storage Tanks and Appurtenances was issued. The guidelines were prepared by the Tanks Seismic Experts Panel (TSEP) and this task was sponsored by DOE, Environmental Management. The TSEP is comprised of a number of consultants known for their knowledge of seismic ground motion and expertise in the analysis of structures, systems and components subjected to seismic loads. The development of these guidelines was managed by staff from Brookhaven National Laboratory, Engineering Research and Applications Division, Department of Nuclear Energy. This paper describes the process used to incorporate the Seismic Design and Evaluation Guidelines for the DOE High-Level Waste Storage Tanks and Appurtenances into the design criteria for the Multi-Function Waste Tank Project at the Hanford Site. This project will design and construct six new high-level waste tanks in the 200 Areas at the Hanford Site. This paper also discusses the vehicles used to ensure compliance to these guidelines throughout Title 1 and Title 2 design phases of the project as well as the strategy used to ensure consistent and cost-effective application of the guidelines by the structural analysts. The paper includes lessons learned and provides recommendations for other tank design projects which might employ the TSEP guidelines

Implementation of seismic design and evaluation guidelines for the Department of Energy high-level waste storage tanks and appurtenances

International Nuclear Information System (INIS)

Conrads, T.J.

1993-01-01

In the fall of 1992, a draft of the Seismic Design and Evaluation Guidelines for the U.S. Department of Energy (DOE) High-level Waste Storage Tanks and Appurtenances was issued. The guidelines were prepared by the Tanks Seismic Experts Panel (TSEP) and this task was sponsored by DOE, Environmental Management. The TSEP comprises a number of consultants known for their understanding of seismic ground motion and expertise in the analysis of structures, systems and components subjected to seismic loads. The development of these guidelines was managed by staff from Brookhaven National Laboratory, Engineering Research and Applications Division, Department of Nuclear Energy. This paper describes the process used to incorporate the Seismic Design and Evaluation guidelines for the DOE High-Level Waste Storage Tanks and Appurtenances into the design criteria for the Multi-Function Waste Tank Project at the Hanford Site. This project will design and construct six new high-level waste tanks in the 200 Areas at the Hanford Site. This paper also discusses the vehicles used to ensure compliance to these guidelines throughout Title 1 and Title 2 design phases of the project as well as the strategy used to ensure consistent and cost-effective application of the guidelines by the structural analysts. The paper includes lessons learned and provides recommendations for other tank design projects that might employ the TSEP guidelines

Reducing aquatic hazards of industrial chemicals: probabilistic assessment of sustainable molecular design guidelines.

Science.gov (United States)

Connors, Kristin A; Voutchkova-Kostal, Adelina M; Kostal, Jakub; Anastas, Paul; Zimmerman, Julie B; Brooks, Bryan W

2014-08-01

Basic toxicological information is lacking for the majority of industrial chemicals. In addition to increasing empirical toxicity data through additional testing, prospective computational approaches to drug development aim to serve as a rational basis for the design of chemicals with reduced toxicity. Recent work has resulted in the derivation of a "rule of 2," wherein chemicals with an octanol-water partition coefficient (log P) less than 2 and a difference between the lowest unoccupied molecular orbital and the highest occupied molecular orbital (ΔE) greater than 9 (log P9 eV) are predicted to be 4 to 5 times less likely to elicit acute or chronic toxicity to model aquatic organisms. The present study examines potential reduction of aquatic toxicity hazards from industrial chemicals if these 2 molecular design guidelines were employed. Probabilistic hazard assessment approaches were used to model the likelihood of encountering industrial chemicals exceeding toxicological categories of concern both with and without the rule of 2. Modeling predicted that utilization of these molecular design guidelines for log P and ΔE would appreciably decrease the number of chemicals that would be designated to be of "high" and "very high" concern for acute and chronic toxicity to standard model aquatic organisms and end points as defined by the US Environmental Protection Agency. For example, 14.5% of chemicals were categorized as having high and very high acute toxicity to the fathead minnow model, whereas only 3.3% of chemicals conforming to the design guidelines were predicted to be in these categories. Considerations of specific chemical classes (e.g., aldehydes), chemical attributes (e.g., ionization), and adverse outcome pathways in representative species (e.g., receptor-mediated responses) could be used to derive future property guidelines for broader classes of contaminants. © 2014 SETAC.

Study on compact design of remote handling equipment for ITER blanket maintenance

International Nuclear Information System (INIS)

Takeda, Nobukazu; Kakudate, Satoshi; Nakahira, Masataka; Shibanuma, Kiyoshi

2006-03-01

In the ITER, the neutrons created by D-T reactions activate structural materials, and thereby, the circumstance in the vacuum vessel is under intense gamma radiation field. Thus, the in-vessel components such as blanket are handled and replaced by remote handling equipment. The objective of this report is to study the compactness of the remote handling equipment (a vehicle/manipulator) for the ITER blanket maintenance. In order to avoid the interferences between the blanket and the equipment during blanket replacement in the restricted vacuum vessel, a compact design of the equipment is required. Therefore, the compact design is performed, including kinematic analyses aiming at the reduction of the sizes of the vehicle equipped with a manipulator handling the blanket and the rail for the vehicle traveling in the vacuum vessel. Major results are as follows: 1. The compact vehicle/manipulator is designed concentration on the reduction of the rail size and simplification of the guide roller mechanism as well as the reduction of the gear diameter for vehicle rotation around the rail. Height of the rail is reduced from 500 mm to 400 mm by a parameter survey for weight, stiffness and stress of the rail. The roller mechanism is divided into two simple functional mechanisms composed of rollers and a pad, that is, the rollers support relatively light loads during rail deployment and vehicle traveling while a pad supports heavy loads during blanket replacement. Regarding the rotation mechanism, the double helical gear is adopted, because it has higher contact ratio than the normal spur gear and consequently can transfer higher force. The smaller double helical gear, 996 mm in diameter, can achieve 26% higher output torque, 123.5 kN·m, than that of the original spur gear of 1,460 mm in diameter, 98 kN·m. As a result, the manipulator becomes about 30% lighter, 8 tons, than the original weight, 11.2 tons. 2. Based on the compact design of the vehicle/manipulator, the

Remote handling equipment design for the HEDL fuel supply program

International Nuclear Information System (INIS)

Metcalf, I.L.

1984-09-01

A process line is currently being developed for fabrication of high exposure mixed uranium-plutonium core assemblies. This paper describes the design philosophy, process flow, equipment, and the handling and radiation shielding techniques used for inspection of Fast Flux Test Facility (FFTF) fuel pins and assembly of Driver Fuel Assemblies (DFAs) 6 figures

Design and fabrication of equipment and devices for a Radiotherapy department

International Nuclear Information System (INIS)

Picon, C.L.; Zaharia B, M.

1998-01-01

The objective of this work is to present the possibility to design and construct utilizing local technology, a series of equipment and devices necessaries for a routine in a Radiotherapy Department with typical budget in the Latin-American hospitals. (Author)

Design considerations, tooling and equipment for remote in-service inspection of radioactive piping and pressure vessel systems

International Nuclear Information System (INIS)

Schmoker, D.S.; Swannack, D.L.

1983-01-01

In-Service Inspection programs are performed to monitor and verify the integrity of a nuclear power plant's primary pressure boundaries. Early detection of abnormal structural or material degradation could preclude serious damage to plant systems. This paper summarizes results obtained in use of remotely-operated nondestructive testing (NDT) equipment for inspection of reactor system components. Experience obtained in operating the Fast Flux Test Facility (FFTF) has provided a basis for field verification of remote NDT equipment designs and has suggested development improvements. Remote Viewing and data gathering systems used include periscopes, borescopes, fiberscopes, hybrid borescopes/fiberscopes, and closed circuit television. A summary of design consideration for inspection equipment and power plant design is presented to achieve improved equipment operation and reduction of plant maintenance downtime

Building Design Guidelines for Interior Architecture Concerned with Animal Researches Facilities

International Nuclear Information System (INIS)

ElDib, A.A. E.

2014-01-01

This paper discusses the most important design guidelines elements and characteristics for animal facilities, in order to achieve and maintain highest efficiency can be, with respect to the pivot role of Interior Architecture as one of the accurate specializations for completing the Architectural Sciences, for designer/s concerned with those types of facilities, (specially those using radioactive materials). These building types known as vivariums, are specially designed, accommodating and having sophisticated controlled environments for the care and maintenance of experimental animals, and are related to, but distinct from other research laboratories premises

Designer's guidebook for first wall/blanket/shield assembly, maintenance, and repair

International Nuclear Information System (INIS)

1983-01-01

This is the initial issue of the guidebook. Since a guidebook of this type must incorporate information concerning a wide range of subjects, much additional data will eventually be included. The guidebook will document, in summary and easily referenceable form, data, designs, design concepts, design guidelines and background information useful to the FWBS and to the Maintenance System designer. In providing guidelines for the AMR of the FWBS, the guidebook must, of necessity, include guidelines for all aspects of maintenance associated with the FWBS. These include most maintenance operations within the reactor room necessary to gain access, identify faults, and handle equipment related to FWBS maintenance. In addition, the guidelines include those required to define facility requirements for handling and repair of FWBS and related reactor components external to the reactor room. Particular emphasis is given to remote maintenance design and operations

Communications received from certain Member States regarding guidelines for transfers of nuclear-related dual-use equipment, materials, software and related technology

International Nuclear Information System (INIS)

2003-01-01

The Director General of the International Atomic Energy Agency has received Notes Verbales dated 28 February 2003 from the Resident Representatives to the Agency of Argentina, Austria, Belgium, Bulgaria, Canada, Cyprus, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Italy, Japan, Kazakhstan, Latvia, Netherlands, Norway, Portugal, Republic of Korea, Slovakia, Slovenia, South Africa, Spain, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America, relating to transfers of nuclear-related dual-use equipment, materials, software and related technology. The purpose of the Note Verbales is to provide further information on those Governments' Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology. In the light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to these Notes Verbales is also reproduced in full

Communications received from certain Member States regarding guidelines for transfers of nuclear-related dual-use equipment, materials, software and related technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-05-16

The Director General of the International Atomic Energy Agency has received Notes Verbales dated 28 February 2003 from the Resident Representatives to the Agency of Argentina, Austria, Belgium, Bulgaria, Canada, Cyprus, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Italy, Japan, Kazakhstan, Latvia, Netherlands, Norway, Portugal, Republic of Korea, Slovakia, Slovenia, South Africa, Spain, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America, relating to transfers of nuclear-related dual-use equipment, materials, software and related technology. The purpose of the Note Verbales is to provide further information on those Governments' Guidelines for Transfers of Nuclear-related Dual-use Equipment, Materials, Software and Related Technology. In the light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to these Notes Verbales is also reproduced in full.

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-02-23

The Director General of the International Atomic Energy Agency has received Notes Verbales dated 25 October 2004 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Brazil, Canada, Cyprus, Czech Republic, Estonia, Finland, France, Greece, Hungary, Italy, Japan, Malta, Netherlands, Norway, Republic of Korea, South Africa, Spain, Sweden, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland and the United States of America relating to the export of nuclear materials, equipment and technology. The purpose of the Notes Verbales is to provide further information on those Governments' guidelines for nuclear transfers. In the light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to these Notes Verbales is also reproduced in full.

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

2005-01-01

The Director General of the International Atomic Energy Agency has received Notes Verbales dated 25 October 2004 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Brazil, Canada, Cyprus, Czech Republic, Estonia, Finland, France, Greece, Hungary, Italy, Japan, Malta, Netherlands, Norway, Republic of Korea, South Africa, Spain, Sweden, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland and the United States of America relating to the export of nuclear materials, equipment and technology. The purpose of the Notes Verbales is to provide further information on those Governments' guidelines for nuclear transfers. In the light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to these Notes Verbales is also reproduced in full

Communications received from certain Member States regarding Guidelines for the Export of Nuclear Material, Equipment and Technology

International Nuclear Information System (INIS)

2003-01-01

The Director General of the International Atomic Energy Agency has received Notes Verbales, dated 28 February 2003, from the Resident Representatives to the Agency of Argentina, Austria, Belgium, Bulgaria, Canada, Cyprus, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Italy, Japan, Kazakhstan, Latvia, Netherlands, Norway, Poland, Portugal, the Republic of Korea, Slovakia, Slovenia, South Africa, Spain, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America, relating to the export of nuclear material, equipment and technology. The purpose of the Note Verbales is to provide further information on those Governments' Guidelines for Nuclear Transfers. In light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to the Notes Verbales is also reproduced in full

Communications received from certain Member States regarding Guidelines for the Export of Nuclear Material, Equipment and Technology

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-05-16

The Director General of the International Atomic Energy Agency has received Notes Verbales, dated 28 February 2003, from the Resident Representatives to the Agency of Argentina, Austria, Belgium, Bulgaria, Canada, Cyprus, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Italy, Japan, Kazakhstan, Latvia, Netherlands, Norway, Poland, Portugal, the Republic of Korea, Slovakia, Slovenia, South Africa, Spain, Sweden, Switzerland, Turkey, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America, relating to the export of nuclear material, equipment and technology. The purpose of the Note Verbales is to provide further information on those Governments' Guidelines for Nuclear Transfers. In light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbales is attached. The attachment to the Notes Verbales is also reproduced in full.

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

2002-01-01

The Director General of the International Atomic Energy Agency has received Notes Verbale, dated 31 August 2001, from the Resident Representatives to the Agency of Argentina, Austria, Belarus, Belgium, Brazil, Bulgaria, Cyprus, Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Italy, Japan, Latvia, Luxembourg, Netherlands, New Zealand, Portugal, Republic of Korea, Romania, Russian Federation, Slovakia, South Africa, Spain, Sweden, Switzerland, Turkey, Ukraine, the United States and the United Kingdom, relating to the export of nuclear material, equipment and technology. The purpose of the Notes Verbale is to provide further information on those Governments' Guidelines for Nuclear Transfers. In the light of the wish expressed at the end of each Note Verbale, the text of the Notes Verbale is attached. The attachment to the Notes Verbale is also reproduced in full

Recent development of aseismic design practice of equipment and piping system in Japan

International Nuclear Information System (INIS)

Shibata, H.

1993-01-01

Recently, the Japanese practice of aseismic (anti-earthquake) design has been reported on at various occasions, and The Technical Guidelines for Aseismic Design of Nuclear Power Plants, JEAG 4601-1987, published by the Japan Electric Nuclear Regulatory Commission (USNRC). Therefore, it is not necessary to describe these guidelines. However, it is rather difficult to keep a record of why and how decisions which recently were made in Japan. The author describes the process to establish Japanese practice for the first ten years in reference. While the fundamental concept has not been changed since 1961, the details have been modified based on new knowledge obtained from recent research and tests. There has been a continuing effort to make this practice a more rational one

Human factors design review guidelines for advanced nuclear control room technologies

International Nuclear Information System (INIS)

O'Hara, J.; Brown, W.; Granda, T.; Baker, C.

1991-01-01

Advanced control rooms (ACRs) for future nuclear power plants are being designed utilizing computer-based technologies. The US Nuclear Regulatory Commission reviews the human engineering aspects of such control rooms to ensure that they are designed to good human factors engineering principles and that operator performance and reliability are appropriately supported in order to protect public health and safety. This paper describes the rationale, general approach, and initial development of an NRC Advanced Control Room Design Review Guideline. 20 refs., 1 fig

Conference on Manned Systems Design : New Methods and Equipment

CERN Document Server

Kraiss, K-F

1981-01-01

This volume contains the proceedings of a conference held in Freiburg, West Germany, September 22-25, 1980, entitled "Manned Systems Design, New Methods and Equipment". The conference was sponsored by the Special Programme Panel on Human Factors of the Scientific Affairs Division of NATO, and supported by Panel VIII, AC/243, on "Human and Biomedical Sciences". Their sponsorship and support are gratefully acknowledged. The contributions in the book are grouped according to the main themes of the conference with special emphasis on analytical approaches, measurement of performance, and simulator design and evaluat ion. The design of manned systems covers many and highly diversified areas. Therefore, a conference under the general title of "Manned Systems Design" is rather ambitious in itself. However, scientists and engineers engaged in the design of manned systems very often are confronted with problems that can be solved only by having several disciplines working together. So it was felt that knowledge about ...

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology. Nuclear-related dual-use transfers

International Nuclear Information System (INIS)

1995-10-01

The Director General has received notes verbales dated 30 June 1995 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, Luxembourg, the Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to the export of nuclear material, equipment and technology. The purpose of the notes verbales is to provide further information on those Governments' Guidelines for Transfers of Nuclear-related Dual-use Equipment, Material and related Technology. In the light of the wish expressed at the end of each note verbale, the text of the notes verbales is annexed hereto. The enclosure to these notes verbales is also reproduced in full in the Annex

Communications received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology. Nuclear-related dual-use transfers

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The Director General has received notes verbales dated 30 June 1995 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, Luxembourg, the Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to the export of nuclear material, equipment and technology. The purpose of the notes verbales is to provide further information on those Governments` Guidelines for Transfers of Nuclear-related Dual-use Equipment, Material and related Technology. In the light of the wish expressed at the end of each note verbale, the text of the notes verbales is annexed hereto. The enclosure to these notes verbales is also reproduced in full in the Annex.

Design guidelines for self-assessment support for adult academic distance learning

NARCIS (Netherlands)

Menendez Blanco, Maria; Van der Veer, Gerrit; Benvenuti, Laura; Kirschner, Paul A.

2011-01-01

Menendez Blanco, M., Van der Veer, G., Benvenuti, L., & Kirschner, P. A. (2011). Design guidelines for self-assessment support for adult academic distance learning. In H-J Shalin (Ed.), Constructing self-discovery learning spaces online: scaffolding and decision making technologies (pp. 169-198).

Towards Cognitive Load Theory as Guideline for Instructional Design in Science Education

Science.gov (United States)

Meissner, Barbara; Bogner, Franz X.

2013-01-01

We applied cognitive load theory in an heuristic out-of-school science lesson. The lesson comprises experiments concerning major attributes of NaCl and was designed for 5th to 8th grade students. Our interest focused on whether cognitive load theory provides sufficient guidelines for instructional design in the field of heuristic science…

Seismic design evaluation guidelines for buried piping for the DOE HLW Facilities

International Nuclear Information System (INIS)

Lin, Chi-Wen; Antaki, G.; Bandyopadhyay, K.; Bush, S.H.; Costantino, C.; Kennedy, R.

1995-01-01

This paper presents the seismic design and evaluation guidelines for underground piping for the Department of Energy (DOE) High-Level-Waste (HLW) Facilities. The underground piping includes both single and double containment steel pipes and concrete pipes with steel lining, with particular emphasis on the double containment piping. The design and evaluation guidelines presented in this paper follow the generally accepted beam-on-elastic-foundation analysis principle and the inertial response calculation method, respectively, for piping directly in contact with the soil or contained in a jacket. A standard analysis procedure is described along with the discussion of factors deemed to be significant for the design of the underground piping. The following key considerations are addressed: the design feature and safety requirements for the inner (core) pipe and the outer pipe; the effect of soil strain and wave passage; assimilation of the necessary seismic and soil data; inertial response calculation for the inner pipe; determination of support anchor movement loads; combination of design loads; and code comparison. Specifications and justifications of the key parameters used, stress components to be calculated and the allowable stress and strain limits for code evaluation are presented

Safety Review related to Commercial Grade Digital Equipment in Safety System

International Nuclear Information System (INIS)

Yu, Yeongjin; Park, Hyunshin; Yu, Yeongjin; Lee, Jaeheung

2013-01-01

The upgrades or replacement of I and C systems on safety system typically involve digital equipment developed in accordance with non-nuclear standards. However, the use of commercial grade digital equipment could include the vulnerability for software common-mode failure, electromagnetic interference and unanticipated problems. Although guidelines and standards for dedication methods of commercial grade digital equipment are provided, there are some difficulties to apply the methods to commercial grade digital equipment for safety system. This paper focuses on regulatory guidelines and relevant documents for commercial grade digital equipment and presents safety review experiences related to commercial grade digital equipment in safety system. This paper focuses on KINS regulatory guides and relevant documents for dedication of commercial grade digital equipment and presents safety review experiences related to commercial grade digital equipment in safety system. Dedication including critical characteristics is required to use the commercial grade digital equipment on safety system in accordance with KEPIC ENB 6370 and EPRI TR-106439. The dedication process should be controlled in a configuration management process. Appropriate methods, criteria and evaluation result should be provided to verify acceptability of the commercial digital equipment used for safety function

Human factors guidelines and methodology in the design of a user computer interface: a case study

International Nuclear Information System (INIS)

Richards, R.E.; Gilmore, W.E.; Haney, L.N.

1986-01-01

In this case study, human factors personnel were requested to participate in a project team of programmers and operations specialists to design a cathode ray tube (CRT) display system for a complex process control application. This presentation describes the process and benefits obtained by incorporating human factors guidelines and methods in system design. Standard human engineering guidelines and techniques were utilized by the project team. In addition, previously published documents and research findings sponsored by the US Nuclear Regulatory Commission (USNRC) were used. Preliminary tasks involved a review of the draft plant procedures. Then, interviews with operators were conducted to establish the initial information for the displays. These initial requirements were evaluated against existing guidelines and criteria to determine the optimal presentation formats. Detailed steps of the approaches used, design decisions made, and tradeoffs that resulted in the final user acceptable design are discussed. 7 refs., 2 figs

Passive solar design strategies: Remodeling guidelines for conserving energy at home

Science.gov (United States)

The idea of passive solar is simple, but applying it effectively does require information and attention to the details of design and construction. Some passive solar techniques are modest and low-cost, and require only small changes in remodeler's typical practice. At the other end of the spectrum, some passive solar systems can almost eliminate a house's need for purchased heating (and in some cases, cooling) energy - but probably at a relatively high first cost. In between are a broad range of energy-conserving passive solar techniques. Whether or not they are cost-effective, practical, and attractive enough to offer a market advantage to any individual remodeler depends on very specific factors such as local costs, climate, and market characteristics. Passive Solar Design Strategies: Remodeling Guidelines For Conserving Energy At Home is written to help give remodelers the information they need to make these decisions. Passive Solar Design Strategies is a package in three basic parts: the guidelines contain information about passive solar techniques and how they work, and provides specific examples of systems which will save various percentages of energy; the worksheets offer a simple, fill-in-the-blank method to pre-evaluate the performance of a specific design; and the worked example demonstrates how to complete the worksheets for a typical residence.

Physical activity education in the undergraduate curricula of all UK medical schools: are tomorrow's doctors equipped to follow clinical guidelines?

Science.gov (United States)

Weiler, Richard; Chew, Stephen; Coombs, Ngaire; Hamer, Mark; Stamatakis, Emmanuel

2012-11-01

Physical activity (PA) is a cornerstone of disease prevention and treatment. There is, however, a considerable disparity between public health policy, clinical guidelines and the delivery of physical activity promotion within the National Health Service in the UK. If this is to be addressed in the battle against non-communicable diseases, it is vital that tomorrow's doctors understand the basic science and health benefits of physical activity. The aim of this study was to assess the provision of physical activity teaching content in the curricula of all medical schools in the UK. Our results, with responses from all UK medical schools, uncovered some alarming findings, showing that there is widespread omission of basic teaching elements, such as the Chief Medical Officer recommendations and guidance on physical activity. There is an urgent need for physical activity teaching to have dedicated time at medical schools, to equip tomorrow's doctors with the basic knowledge, confidence and skills to promote physical activity and follow numerous clinical guidelines that support physical activity promotion.

Vibration aging of diesel-engine mounted electrical equipment

International Nuclear Information System (INIS)

Lee, B.J.; Morton, W.C.

1994-01-01

The Emergency Diesel Generator (EDG) in a Nuclear Power Plant is considered to be a component which is essential to safe plant operation. Failures of auxiliary equipment directly mounted on the EDG creates costly repairs, and compromises the engine's availability and reliability. Although IEEE-323 requires addressing of safety-related components due to mechanically induced vibration, very few guidelines exist in the nuclear industry to show how this may be accounted for. Most engine vendors rely on the empirical experience data as the basis of their evaluation for vibration. Upgrade of engine controls, addition of monitoring devices and other engine modifications require design and installation of new equipment to be mounted directly on the engine. This necessitates the evaluation for engine-induced vibration which is considered to be one of the most severe design parameters. This paper discusses the engine vibration characteristics, and the acquisition of extensive field vibration data on the diesel engine under operating conditions. The data is then used to develop life cycle vibration qualification test profiles that can be applied with confidence in a laboratory environment to qualify engine-mounted equipment. The intent is to validate a product's ability to survive under worst case, extended service on-engine conditions. This paper describes the procedures and approaches used to achieve those goals, and provides developed profile examples and test results

Practical Design Guidelines of qZSI Based Step-Up DC/DC Converter

Science.gov (United States)

Zakis, Janis; Vinnikov, Dmitri; Roasto, Indrek; Jalakas, Tanel

2010-01-01

This paper presents some design guidelines for a new voltage fed step-up DC/DC isolated converter. The most significant advantage of proposed converter is voltage buck-boost operation on single stage. The most promising application for proposed converter is in the field of distributed power generation e.g. fuel cells or photovoltaic. The most sensitive issues - such as power losses caused by high currents in the input side of converter and high transient overvoltages across the inverter bridge caused by stray inductances were discussed and solved. The proposals and recommendations to overcome these issues are given in the paper. The Selection and design guidelines of converter elements are proposed and explained. The prototype of proposed converter was built and experimentally tested. Some results are presented and evaluated.

Design of channel experiment equipment for measuring coolant velocity of innovative research reactor

International Nuclear Information System (INIS)

Muhammad Subekti; Endiah Puji Hastuti; Dedi Heriyanto

2014-01-01

The design of innovative high flux research reactor (RRI) requires high power so that the capability core cooling requires to be improved by designing the faster core coolant velocity near to the critical velocity limit. Hence, the critical coolant velocity as the one of the important parameter of the reactor safety shall be measured by special equipment to the velocity limit that may induce fuel element degradation. The research aims is to calculate theoretically the critical coolant velocity and to design the special experiment equipment namely EXNal for measuring the critical coolant velocity in fuel element subchannel of the RRI. EXNal design considers the critical velocity calculation result of 20.52 m/s to determine the variation of flow rate of 4.5-29.2 m 3 /h, in which the experiment could simulate the 1-4X standard coolant velocity of RSG-GAS as well as destructive test of RRI's fuel plate. (author)

Assessment of EPRI water chemistry guidelines for new nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Kim, K.; Fruzzetti, K.; Garcia, S. [Electric Power Research Inst., Palo Alto, California (United States); Eaker, R. [Richard W. Eaker, LLC, Matthews, North Carolina (United States); Giannelli, J.; Tangen, J. [Finetech, Inc., Parsippany, New Jersey (United States); Gorman, J.; Marks, C. [Dominion Engineering, Inc., Reston, Virginia (United States); Sawochka, S. [NWT Corp., San Jose, California (United States)

2010-07-01

Water chemistry control technologies for nuclear power plants have been significantly enhanced over the past few decades to improve material and equipment reliability and fuel performance, and to minimize radionuclide production and transport. Chemistry Guidelines have been developed by the Electric Power Research Institute (EPRI) for current operating plants and have been intermittently revised over the past twenty-five years for the protection of systems and components and for radiation management. As new plants are being designed for improved safety and increased power production, it is important to ensure that the designs consider implementation of industry approved water chemistry controls. In parallel, the industry will need to consider and develop updated water chemistry guidelines as well as plant startup and operational strategies based on the advanced plant designs. In 2010, EPRI began to assess chemistry control strategies at advanced plants, based on the Design Control Documents (DCDs), Combined Construction and Operating License Applications (COLA), and operating experiences (where they exist) against current Water Chemistry Guidelines. Based on this assessment, differences between planned chemistry operations at new plants and the current Guidelines will be identified. This assessment will form the basis of future activities to address these differences. The project will also assess and provide, as feasible, water chemistry guidance for startup and hot functional testing of the new plants. EPRI will initially assess the GE-Hitachi/Toshiba ABWR and the Westinghouse AP1000 designs. EPRI subsequently plans to assess other plant designs such as the AREVA U.S. EPR, Mitsubishi Heavy Industries (MHI) U.S. APWR, and GE-Hitachi (GE-H) ESBWR. This paper discusses the 2010 assessments of the ABWR and AP1000. (author)

Assessment of EPRI water chemistry guidelines for new nuclear power plants

International Nuclear Information System (INIS)

Kim, K.; Fruzzetti, K.; Garcia, S.; Eaker, R.; Giannelli, J.; Tangen, J.; Gorman, J.; Marks, C.; Sawochka, S.

2010-01-01

Water chemistry control technologies for nuclear power plants have been significantly enhanced over the past few decades to improve material and equipment reliability and fuel performance, and to minimize radionuclide production and transport. Chemistry Guidelines have been developed by the Electric Power Research Institute (EPRI) for current operating plants and have been intermittently revised over the past twenty-five years for the protection of systems and components and for radiation management. As new plants are being designed for improved safety and increased power production, it is important to ensure that the designs consider implementation of industry approved water chemistry controls. In parallel, the industry will need to consider and develop updated water chemistry guidelines as well as plant startup and operational strategies based on the advanced plant designs. In 2010, EPRI began to assess chemistry control strategies at advanced plants, based on the Design Control Documents (DCDs), Combined Construction and Operating License Applications (COLA), and operating experiences (where they exist) against current Water Chemistry Guidelines. Based on this assessment, differences between planned chemistry operations at new plants and the current Guidelines will be identified. This assessment will form the basis of future activities to address these differences. The project will also assess and provide, as feasible, water chemistry guidance for startup and hot functional testing of the new plants. EPRI will initially assess the GE-Hitachi/Toshiba ABWR and the Westinghouse AP1000 designs. EPRI subsequently plans to assess other plant designs such as the AREVA U.S. EPR, Mitsubishi Heavy Industries (MHI) U.S. APWR, and GE-Hitachi (GE-H) ESBWR. This paper discusses the 2010 assessments of the ABWR and AP1000. (author)

Physical protection equipment study. Final report

International Nuclear Information System (INIS)

Haberman, W.

1977-06-01

This report summarizes the work performed by MITRE for the U.S. Nuclear Regulatory Commission. The major products of this effort are a Catalog of Physical Protection Equipment, a Guide for Evaluation of Physical Protection Equipment, a book of Reference Materials, and a set of guidelines for use in the development of a methodology for measuring levels of security system effectiveness. A summary of recommendations resulting from this study is also presented

Communication received from certain member states regarding guidelines for the export of nuclear material, equipment and technology

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-09-16

The document contains the text of note verbales dated 17 October 1996 received by the Director General of the IAEA from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, the Republic of Korea, Luxembourg, the Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Russian Federation, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to export of nuclear material, equipment and technology. A similar note verbal dated 30 July 1997 has been received by the Director General of the IAEA from the Resident Representative to the Agency of Brazil. The purpose of the notes verbale is to provide further information on those Governments` Guidelines for Nuclear Transfers.

Communication received from certain member states regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1997-01-01

The document contains the text of note verbales dated 17 October 1996 received by the Director General of the IAEA from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, the Republic of Korea, Luxembourg, the Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Russian Federation, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, Ukraine, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to export of nuclear material, equipment and technology. A similar note verbal dated 30 July 1997 has been received by the Director General of the IAEA from the Resident Representative to the Agency of Brazil. The purpose of the notes verbale is to provide further information on those Governments' Guidelines for Nuclear Transfers

Report on equipment availability for the ten-year period, 1966--1975

Energy Technology Data Exchange (ETDEWEB)

1976-12-01

This is an annual report of availability and outage statistics for electric power generating facilities operating in the United States. A list of utility organizations voluntarily participating in the EEI Equipment Availability Program in 1975 is located in Appendix F. All summary reports in this publication are for the 10-year period 1966-1975. Each reporting utility company has received reports on individual units for which data were submitted. Also, selected major equipment manufacturers receive copies of computer reports showing an analysis of the data for their equipment. Revised reporting instructions to incorporate Safety and Environmental Requirement Cause Codes were issued effective January 1, 1976. In addition, provisions were made for identifying major equipment manufactured outisde of the United States or under foreign license. Recognizing that an Annual Report contains only a limited amount of general outage data in selected categories, the Task Force has agreed to perform special analyses of the data bank if the cost of computer services is met by the requestor and if the required analysis conforms to some designated policy guidelines.

The design and development of Project Warrior equipment

International Nuclear Information System (INIS)

Thompson, V.R.; Jerram, K.

1987-01-01

The project Warrior standing for welding and repair robot in Oldbury reactors is the culmination of more than 7 years of conceptual thinking, research, development design and manufacture. The tile encompasses the whole project which includes a work performing manipulator, serving manipulator, the manipulators control system and consoles, a welding head and rangefinder with its associated control system and consoles and a large amount of auxiliary equipment. The system at the forefront of today's technology has been manufactured to carry out remote welding in nuclear reactors, on plate with an oxide covering of up to 200 microns

Human Systems Interface Design Methods Using Ecological Interface Design Principles

International Nuclear Information System (INIS)

Hong, Seung Kweon; Park, Jung Chul; Kim, Sun Su; Sim, Kwang Pyo; Yuk, Seung Yul; Choi, Jae Hyeon; Yoon, Seung Hyun

2009-12-01

The results of this study categorized into two parts. The first part is the guidelines for EID designs. The procedure to observe for EID design is composed of 6 steps; 1) to define a target system, 2) to make an abstraction hierarchy model, 3) to check the link structure among each components included in the layers of abstraction hierarchy model, 4) to transform information requirements to variables, 5) to make the graphs related to each variables, 6) to check the graphs by visual display design principles and heuristic rules. The second part is an EID design alternative for nuclear power plant. The EID for high level function represents the energy balance and energy flow in each loop of nuclear power plant. The EID for middle level function represents the performance indicators of each equipment involved in the all processes of changing from coolants to steam. The EID for low level function represents the values measured in each equipment such as temperature, pressure, water level and so on

Overview of Mobile Equipment Used in Case of Beyond Design Basis Accident at NPP Krsko

International Nuclear Information System (INIS)

Lukacevic, H.; Kopinc, D.; Ivanjko, M.

2016-01-01

Terrorist attack in USA in the September 11, 2001 and accident at the Fukushima - Daiichi Nuclear Power Station in the March 11, 2011 highlight the importance of mitigating strategies in responding to Beyond Design Basis Accident (BDBA), while ensuring cooling of reactor core, containment and spent fuel pool. Nuclear Power Plant Krsko (NEK) has acquired additional mobile equipment and made necessary modifications on existing systems for the connection of this equipment (fast couplers). Usage of mobile equipment is not only limited to design basis accident (DBA), but, also to prevent and mitigate the consequences in case of BDBA, when other plant systems are not available. NEK also decided to take steps for upgrade of safety measures and prepared Safety Upgrade Program (SUP), which is consistent with the nuclear industry response to the Fukushima accident and is implementing main projects and modifications related to SUP. NEK mobile equipment is not required to operate under normal reactor plant operation except for periodic surveillance testing and is incorporated into the normal training process. Equipment is dislocated from the reactor building and most of the equipment is located in the new building, able to withstand extreme natural events, including earthquakes and tornadoes. The usage of all mobile equipment is prescribed as an additional option in NEK operating procedures in following cases and enables following options: filling various tanks, filling the steam generators, filling the containment, additional compressed air source, spent fuel pool refilling and spraying, alternative power supply. This document provides an overview of NEK mobile equipment, which consists of various mobile fire protection pumps, air compressors, protective equipment, fire trucks, diesel generators. Sufficient fuel supply for the equipment is provided on site for a minimum three days of operation. (author).

Application of U.S. export controls to DOE technical exchanges: New guidelines on export control and nonproliferation

International Nuclear Information System (INIS)

Lisann, E.G.; Hollander, Z.; Rudolph, R.R.

1995-01-01

As the Department of Energy's nuclear weapon's complex shrinks, concern regarding the proliferation of nuclear weapons technology through the release of export-controlled equipment, materials and information has come to the fore. In November, 1994 Under Secretary Charles Curtis issued new guidelines on export control and nonproliferation. The new policies and procedures are designed to help Department of Energy Headquarters Offices, Operations Offices, Area Offices, laboratories and contractors implement a consistent and technologically sound policy regarding DOE transfers of unclassified equipment, materials and information that could adversely affect US nuclear nonproliferation objectives or national security. The DOE Export Control Division has developed a multi-faceted program of guidelines and training materials to sensitize DOE and DOE-contractors to their responsibilities and to teach them how to evaluate the proliferation risks of their activities

Seismic design practice for Indian pressurized heavy water reactors

International Nuclear Information System (INIS)

Chhatre, A.G.; Ingole, S.M.; Bhardwaj, S.A.

1996-01-01

Nuclear power plants designed in India in the last twenty years have been designed for earthquake loading using the current licensing practices. Designers and equipment suppliers have therefore been required to consider seismic loading as a major load case. In India, the nuclear power plants have been seismically qualified using state-of-the-art techniques involving both seismic analysis and testing to ensure that the power plant is capable of safely surviving an earthquake that the plant is likely to experience during their operating life. Guidelines and criteria for meeting the qualification requirements are followed as given in various AERB (Indian Atomic Energy Regulatory Board), NRC, IAEA guides, ASME codes and IEEE standards. In this paper various methods available for qualification of structures, systems, mechanical and electrical equipment are explained. The approach and guidelines used within Indian nuclear industry which are evolved from simple analytical requirements to the more elaborate current requirements involving complex analysis and testing on shake table are also summarized

System Design Description PFP Thermal Stabilization

International Nuclear Information System (INIS)

RISENMAY, H.R.

2000-01-01

The purpose of this document is to provide a system design description (SDD) and design basis for the Plutonium Finishing Plant (PFP) Thermal Stabilization project. The chief objective of the SDD is to document the Structures, Systems, and Components (SSCs) that establish and maintain the facility Safety Envelope necessary for normal safe operation of the facility; as identified in the FSAR, the OSRs, and Safety Assessment Documents (SADs). This safety equipment documentation should satisfy guidelines for the SDD given in WHC-SD-CP-TI-18 1, Criteria for Identification and Control of Equipment Necessary for Preservation of the Safety Envelope and Safe Operation of PFP. The basis for operational, alarm response, maintenance, and surveillance procedures are also identified and justified in this document. This document and its appendices address the following elements of the PFP Thermal Stabilization project: Functional and design requirements; Design description; Safety Envelope Analysis; Safety Equipment Class; and Operational, maintenance and surveillance procedures

Designer's guidebook for first wall/blanket/shield assembly, maintenance, and repair

Energy Technology Data Exchange (ETDEWEB)

1983-12-30

This is the initial issue of the guidebook. Since a guidebook of this type must incorporate information concerning a wide range of subjects, much additional data will eventually be included. The guidebook will document, in summary and easily referenceable form, data, designs, design concepts, design guidelines and background information useful to the FWBS and to the Maintenance System designer. In providing guidelines for the AMR of the FWBS, the guidebook must, of necessity, include guidelines for all aspects of maintenance associated with the FWBS. These include most maintenance operations within the reactor room necessary to gain access, identify faults, and handle equipment related to FWBS maintenance. In addition, the guidelines include those required to define facility requirements for handling and repair of FWBS and related reactor components external to the reactor room. Particular emphasis is given to remote maintenance design and operations.

Terrestrial Environment (Climatic) Criteria Guidelines for use in Aerospace Vehicle Development. 2008 Revision

Science.gov (United States)

Johnson, D. L. (Editor)

2008-01-01

This document provides guidelines for the terrestrial environment that are specifically applicable in the development of design requirements/specifications for NASA aerospace vehicles, payloads, and associated ground support equipment. The primary geographic areas encompassed are the John F. Kennedy Space Center, FL; Vandenberg AFB, CA; Edwards AFB, CA; Michoud Assembly Facility, New Orleans, LA; John C. Stennis Space Center, MS; Lyndon B. Johnson Space Center, Houston, TX; George C. Marshall Space Flight Center, Huntsville, AL; and the White Sands Missile Range, NM. This document presents the latest available information on the terrestrial environment applicable to the design and operations of aerospace vehicles and supersedes information presented in NASA-HDBK-1001 and TM X-64589, TM X-64757, TM-78118, TM-82473, and TM-4511. Information is included on winds, atmospheric thermodynamic models, radiation, humidity, precipitation, severe weather, sea state, lightning, atmospheric chemistry, seismic criteria, and a model to predict atmospheric dispersion of aerospace engine exhaust cloud rise and growth. In addition, a section has been included to provide information on the general distribution of natural environmental extremes in the conterminous United States, and world-wide, that may be needed to specify design criteria in the transportation of space vehicle subsystems and components. A section on atmospheric attenuation has been added since measurements by sensors on certain Earth orbital experiment missions are influenced by the Earth s atmosphere. There is also a section on mission analysis, prelaunch monitoring, and flight evaluation as related to the terrestrial environment inputs. The information in these guidelines is recommended for use in the development of aerospace vehicle and related equipment design and associated operational criteria, unless otherwise stated in contract work specifications. The terrestrial environmental data in these guidelines are

Progress towards developing consistent design and evaluation guidelines for US Department of Energy facilities subjected to natural phenomena

International Nuclear Information System (INIS)

Murray, R.C.

1987-01-01

Probabilistic definitions of earthquake, wind, and tornado hazards for many DOE facilities throughout the United States have been developed. In addition, definitions of the flood hazards which might affect these locations are currently being developed. We have prepared a document to provide guidance and criteria for DOE facility managers to assure that DOE facilities are adequately constructed to resist the effects of natural phenomena such as earthquake, strong wind, and flood. The intent of this document is to provide instruction on how to utilize the hazard definitions to evaluate existing facilities and design new facilities in a manner such that the risk of adverse consequences is consistent with the cost, function, and danger to the public or environment. A conference and six mini-courses were organized on natural phenomena hazards mitigation. This provided a mechanism for technology transfer to the DOE community. Complementary manuals have also been developed for 1) suspended ceiling systems and recommendations for bracing them, 2) practical equipment seismic upgrade and strengthening guidelines, and 3) suggested structural details for wind design. These manuals are intended to provide input and guidance for ongoing site safety programs. (orig./HP)

Progress towards developing consistent design and evaluation guidelines for US Department of Energy facilities subjected to natural phenomena

International Nuclear Information System (INIS)

Murray, R.C.

1987-01-01

Probabilistic definitions of earthquake, wind, and tornado hazards for many Department of Energy (DOE) facilities throughout the United States have been developed. In addition, definitions of the flood hazards which might affect these locations are currently being developed. The authors have prepared a document to provide guidance and criteria for DOE facility managers to assure that DOE facilities are adequately constructed to resist the effects of natural phenomena such as earthquake, strong wind, and flood. The intent of this document is to provide instruction on how to utilize the hazard definitions to evaluate existing facilities and design new facilities in a manner such that the risk of adverse consequences is consistent with the cost, function, and danger to the public or environment. A conference and six mini-courses were organized on natural phenomena hazards mitigation. This provided a mechanism for technology transfer to the DOE community. Complementary manuals have also been developed for 1) suspended ceiling systems and recommendations for bracing them, 2) practical equipment seismic upgrade and strengthening guidelines, and 3) suggested structural details for wind design. These manuals are intended to provide input and guidance for ongoing site safety programs

Passive solar design strategies: Remodeling guidelines for conserving energy at home

Energy Technology Data Exchange (ETDEWEB)

1991-01-01

The idea of passive solar is simple, but applying it effectively does require information and attention to the details of design and construction. Some passive solar techniques are modest and low-cost, and require only small changes in remodeler's typical practice. At the other end of the spectrum, some passive solar systems can almost eliminate a house's need for purchased heating (and in some cases, cooling) energy -- but probably at a relatively high first cost. In between are a broad range of energy-conserving passive solar techniques. Whether or not they are cost-effective, practical and attractive enough to offer a market advantage to any individual remodeler depends on very specific factors such as local costs, climate, and market characteristics. Passive solar design strategies: Remodeling Guidelines For Conserving Energy At Homes is written to help give remodelers the information they need to make these decisions. Passive Solar Design Strategies is a package in three basic parts: The Guidelines contain information about passive solar techniques and how they work, and provides specific examples of systems which will save various percentages of energy; The Worksheets offer a simple, fill-in-the-blank method to pre-evaluate the performance of a specific design; The Worked Example demonstrates how to complete the worksheets for a typical residence.

Household factors, family behavior patterns, and adherence to dietary and physical activity guidelines among children at risk for obesity.

Science.gov (United States)

Kunin-Batson, Alicia S; Seburg, Elisabeth M; Crain, A Lauren; Jaka, Meghan M; Langer, Shelby L; Levy, Rona L; Sherwood, Nancy E

2015-01-01

To describe the proportion of children adhering to recommended physical activity and dietary guidelines, and examine demographic and household correlates of guideline adherence. Cross-sectional (pre-randomization) data from a behavioral intervention trial designed to prevent unhealthy weight gain in children. A total of 421 children (aged 5-10 years) at risk for obesity (body mass index percentile, 70-95). Physical activity (accelerometry), screen time (parent survey), and fruit and vegetable and sugar-sweetened beverage intake (24-hour dietary recall). Proportions meeting guidelines were calculated. Logistic regression examined associations between demographic and household factors and whether children met recommended guidelines for (1) physical activity (≥ 60 min/d), (2) screen time (≤ 2 h/d), (3) fruit and vegetable intake (≥ 5 servings/d), and (4) sugar-sweetened beverage avoidance. Few children met more than 1 guideline. Only 2% met all 4 recommended guidelines and 19% met none. Each guideline had unique sociodemographic and domain-specific household predictors (ie, availability of certain foods and beverages, media, and active play and exercise equipment). Families equipped to promote healthy child behavior patterns in 1 activity or dietary domain may not be in others. Results have implications for the development of interventions to affect children's weight-related behaviors and growth trajectories. Copyright © 2015 Society for Nutrition Education and Behavior. Published by Elsevier Inc. All rights reserved.

Design of a compact low-power human-computer interaction equipment for hand motion

Science.gov (United States)

Wu, Xianwei; Jin, Wenguang

2017-01-01

Human-Computer Interaction (HCI) raises demand of convenience, endurance, responsiveness and naturalness. This paper describes a design of a compact wearable low-power HCI equipment applied to gesture recognition. System combines multi-mode sense signals: the vision sense signal and the motion sense signal, and the equipment is equipped with the depth camera and the motion sensor. The dimension (40 mm × 30 mm) and structure is compact and portable after tight integration. System is built on a module layered framework, which contributes to real-time collection (60 fps), process and transmission via synchronous confusion with asynchronous concurrent collection and wireless Blue 4.0 transmission. To minimize equipment's energy consumption, system makes use of low-power components, managing peripheral state dynamically, switching into idle mode intelligently, pulse-width modulation (PWM) of the NIR LEDs of the depth camera and algorithm optimization by the motion sensor. To test this equipment's function and performance, a gesture recognition algorithm is applied to system. As the result presents, general energy consumption could be as low as 0.5 W.

Integration of educational methods and physical settings: design guidelines for High/Scope methodology in pre-schools

Directory of Open Access Journals (Sweden)

Shirin Izadpanah

2014-06-01

Full Text Available Quality design and appropriate space organization in preschool settings can support preschool children's educational activities. Although the relationship between the well-being and development of children and physical settings has been emphasized by many early childhood researchers, there is still a need for theoretical design guidelines that are geared towards the improvement of this issue. This research focuses on High/Scope education and aims to shape a theoretical guideline that raises teachers' awareness about the potential of learning spaces and guides them to improve the quality of the physical spaces. To create a theoretical framework, reliable sources are investigated in the light of High/Scope education and the requirements of pre-school children educational spaces. Physical space characteristics, the preschool child's requirements and High/Scope methodology identified design inputs, design considerations and recommendations that shape the final guideline for spatial arrangement in a High/Scope setting are integrated. Discussions and suggestions in this research benefit both designers and High/ Scope teaching staff. Results help High/Scope teaching staff increase the quality of a space in an educational setting without having an architectural background. The theoretical framework of the research allows designers to consider key features and users' possible activities in High/ Scope settings and shape their designs accordingly.

IMAGE Programming Guidelines

Energy Technology Data Exchange (ETDEWEB)

Stehfest, E; De Waal, L.

2010-09-15

This document describes the requirements and guidelines for the software of the IMAGE system. The motivation for this report was a substantial restructuring of the source code for IMAGE version 2.5. The requirements and guidelines relate to design considerations as well as to aspects of maintainability and portability. The design considerations determine guidelines about subjects, such as program structure, model hierarchy, the use of data modules, and the error message system. Maintainability and portability aspects determine the guidelines on, for example, the Fortran 90 standard, naming conventions, code lay-out, and internal documentation.

Typical design/qualification acceptance criteria for newly installed pipelines and equipment components of VVER-type NPPs

International Nuclear Information System (INIS)

Masopust, R.

2003-01-01

This paper describes in general the typical design/qualification acceptance criteria and seismic acceptance criteria in particular that are applicable for important to safety newly installed pipelines and equipment components of VVER-type already existing NPPs, specifically during the design verification phase of this newly installed equipment. These criteria are currently used for VVER 440-213 and VVER 1000 NPPs in Czech Republic and in Slovakia. The similar criteria are also used in Hungary. (author)

Improvement of Productivity in TIG Welding Plant by Equipment Design in Orbit

Science.gov (United States)

Gnanavel, C.; Saravanan, R.; Chandrasekaran, M.; Jayakanth, J. J.

2017-03-01

Measurements and improvements are very indispensable task at all levels of management. Here some samples are, at operator level: Measuring operating parameters to ensure OEE (Overall Equipment Effectiveness) and measuring Q components performance to ensure quality, at supervisory level: measuring operator’s performance to ensure labour utility at managerial level: production and productivity measurements and at top level capital and capacity utilization. An often accepted statement is “Improvement is impossible without measurement”. Measurements often referred as observation. The case study was conducted at Government Boiler factory in India. The scientific approach followed for indentifying non value added activities. Personalised new equipment designed and installed to achieve productivity improvement of 85% for a day. The new equipment can serve 360o around its axis hence it simplified loading and unloading procedures as well as reduce their times and ensured effective space and time.

Repository Planning, Design, and Engineering: Part II-Equipment and Costing.

Science.gov (United States)

Baird, Phillip M; Gunter, Elaine W

2016-08-01

Part II of this article discusses and provides guidance on the equipment and systems necessary to operate a repository. The various types of storage equipment and monitoring and support systems are presented in detail. While the material focuses on the large repository, the requirements for a small-scale startup are also presented. Cost estimates and a cost model for establishing a repository are presented. The cost model presents an expected range of acquisition costs for the large capital items in developing a repository. A range of 5,000-7,000 ft(2) constructed has been assumed, with 50 frozen storage units, to reflect a successful operation with growth potential. No design or engineering costs, permit or regulatory costs, or smaller items such as the computers, software, furniture, phones, and barcode readers required for operations have been included.

Power system engineering planning, design, and operation of power systems and equipment

CERN Document Server

Schlabbach, Juergen

2014-01-01

With its focus on the requirements and procedures of tendering and project contracting, this book enables the reader to adapt the basics of power systems and equipment design to special tasks and engineering projects, e.g. the integration of renewable energy sources.

A Digital Power Quality Monitoring Equipment Designed for Digital Substation

Science.gov (United States)

Li, Wei; Wang, Xin; Geng, Jiewen

2018-01-01

Taking into account both current status and development trend of digital substation, this paper proposed a design of a new multi-channelled digital power quality monitoring equipment with high compatibility. The overall functional structure, hardware architecture, software architecture, interface architecture and some key techniques such as IEC 61850 modelling of transient event and harmonic measurement method under the condition of non-synchronous sampling are described in this paper.

Symphony: A case study for exploring and describing design methods and guidelines for learner-centered design

Science.gov (United States)

Quintana, Christopher

Learner-centered design is an evolving software design perspective addressing the needs of learners---a specific audience trying to work in and understand new work practices in which they have a novice or naive understanding. Learner-centered design involves designing software that incorporates work support features (or scaffolding features) informed by social constructivist learning theories. By adopting a constructivist "learning by doing" perspective, scaffolds should support learners so they can mindfully engage in previously inaccessible work activity, which in turn allows those learners to progressively gain a better understanding of the new work. While there is an intuitive notion of "learner-centered design", there is less specific design information for developing learner-centered software. As a result, learner-centered software results from "educated guesses" and ad-hoc design approaches rather than from systematic design methods. Thus there is a need for specific design guidance to facilitate the development of learner-centered tools that help learners see the tasks, terminology, tools, etc. in the new work context and engage in that work. The research in this dissertation provides a more specific base of learner-centered design descriptions, methods, and guidelines to analyze work practices and design and evaluate scaffolds. The research approach involves using the development of Symphony---a scaffolded integrated tool environment for high-school students learning the work of computational science inquiry---as a case study to develop the learner-centered design approach. Symphony incorporates a variety of science tools with process scaffolding to support students in performing complex air pollution investigations. Six ninth-grade students used Symphony to investigate air quality questions for several weeks in an environmental science class. The student testing helped assess the effectiveness of the software scaffolding and in turn, the learner

Prototypical spent fuel rod consolidation equipment preliminary design report: Volume 2, Drawings

International Nuclear Information System (INIS)

1986-01-01

This volume consists of 65 E size drawings and 4 sketches of the NUS spent fuel rod consolidation equipment. The drawings have been grouped into categories; a detailed list of the drawings is included. The sketches prepared during the preliminary design process have been included

Expansion of the acceptance program: nitrous oxide scavenging equipment and nitrous oxide trace gas monitoring equipment

Energy Technology Data Exchange (ETDEWEB)

1977-10-01

The Acceptance Program for dental materials and devices and the general guidelines for submission of products have been reported in the Journal (88:615 March 1974). At its April 1977 meeting, the Council included equipment for scavenging and monitoring trace nitrous oxide gas in its Acceptance Program. The Council has established the effective date for classification of products under these two sets of guidelines as one year from the date of publication of this announcement. After that date, classification of a product will be required before promotion or exhibition in Association media.

Design of remote handling equipment for the ITER NBI

Energy Technology Data Exchange (ETDEWEB)

Oka, Kiyoshi; Tada, Eisuke [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1999-08-01

The ITER machine has three Neutral Beam Injectors (NBIs) placed tangential to the plasma at a minimum radius of 6.25 m. During operation, neutrons produced by the D-T reactions will irradiate the NBI structure and it will become radioactive. Radiation levels will be such that all subsequent maintenance of the NBIs must be carried out remotely. The presence of tritium and possibly radioactive dust requires that precautions be taken during maintenance to prevent the escape of these contaminants beyond the prescribed boundaries. The scope of this task is both the development of remote maintenance procedures and the design of the remote handling equipment to handle the NBIs. This report describes the design of remote handling tools for the ion source and its filaments, transfer cask, maintenance time, manufacturing schedule and cost estimation. (author)

Computerization of guidelines: towards a "guideline markup language".

Science.gov (United States)

Dart, T; Xu, Y; Chatellier, G; Degoulet, P

2001-01-01

Medical decision making is one of the most difficult daily tasks for physicians. Guidelines have been designed to reduce variance between physicians in daily practice, to improve patient outcomes and to control costs. In fact, few physicians use guidelines in daily practice. A way to ease the use of guidelines is to implement computerised guidelines (computer reminders). We present in this paper a method of computerising guidelines. Our objectives were: 1) to propose a generic model that can be instantiated for any specific guidelines; 2) to use eXtensible Markup Language (XML) as a guideline representation language to instantiate the generic model for a specific guideline. Our model is an object representation of a clinical algorithm, it has been validated by running two different guidelines issued by a French official Agency. In spite of some limitations, we found that this model is expressive enough to represent complex guidelines devoted to diabetes and hypertension management. We conclude that XML can be used as a description format to structure guidelines and as an interface between paper-based guidelines and computer applications.

Structural design guidelines for concrete bridge decks reinforced with corrosion-resistant reinforcing bars.

Science.gov (United States)

2014-10-01

This research program develops and validates structural design guidelines and details for concrete bridge decks with : corrosion-resistant reinforcing (CRR) bars. A two-phase experimental program was conducted where a control test set consistent : wi...

OEE and equipment effectiveness : an evaluation

NARCIS (Netherlands)

Ron, de A.J.; Rooda, J.E.

2006-01-01

The overall equipment effectiveness or efficiency (OEE) is a metric that has been accepted in the semiconductor industry. OEE is simple and clear, and standards and guidelines have been developed. Nonetheless, the literature indicates imperfections in applying OEE with regard to the time base and

Methodological framework for the ergonomic design of children's playground equipment: a Serbian experience.

Science.gov (United States)

Grozdanovic, Miroljub; Jekic, Savko; Stojiljkovic, Evica

2014-01-01

Adequate application of the static and dynamic anthropometric measures of pre-school children in ergonometric design of children's playground equipment should eliminate all dangers and difficulties in their use. Possibilities of injuries, insecure movements, discomfort able positions and some other dangerous actions may be minimized; and safety and health protection of pre-school children will be increased. Children's playground represents a significant space of activity for pre-school children. Therefore, it is necessary to apply ergonomic principles which contribute to the adjustment of the playground elements to children's anatomic features. Based on the results presented in this paper, new constructions were designed and new playgrounds were installed in Serbia. Participants were children from three pre-school age groups: Junior age group (3-4 years of age, 17 children), Medium age group (4-5 years of age, 22 children), and Senior age group (5-6 years of age, 26 children). Thirty-one static anthropometric measures (12 in standing position, 11 in sitting position, 7 related to dimensions of hand, foot an head, with body weight and shoe size) and 15 dynamic anthropometric measures (7 in standing position, 6 in sitting position and 2 dimension of foot and hand) were defined for the study. Measurements were taken using an anthrop-meter, a flexible measuring tape. Equations for ergonomic design of children's playground elements were also defined. Basic statistical data of static and dynamic anthropometric measurements of the pre-school children are presented in this paper, as well as the statistical calculation of the corrective anthropometric measurements. Measurements were performed in "Poletarac" kindergarten, part of the pre-school institution "Radost" in Cacak. Elements of playground equipment in "Bambi" kindergarten in Kragujevac (the Indian tent "wigwam", gate-house, swing and carousel) were designed and built using these parameters. Based on the obtained

Design Methodology of Process Layout considering Various Equipment Types for Large scale Pyro processing Facility

International Nuclear Information System (INIS)

Yu, Seung Nam; Lee, Jong Kwang; Lee, Hyo Jik

2016-01-01

At present, each item of process equipment required for integrated processing is being examined, based on experience acquired during the Pyropocess Integrated Inactive Demonstration Facility (PRIDE) project, and considering the requirements and desired performance enhancement of KAPF as a new facility beyond PRIDE. Essentially, KAPF will be required to handle hazardous materials such as spent nuclear fuel, which must be processed in an isolated and shielded area separate from the operator location. Moreover, an inert-gas atmosphere must be maintained, because of the radiation and deliquescence of the materials. KAPF must also achieve the goal of significantly increased yearly production beyond that of the previous facility; therefore, several parts of the production line must be automated. This article presents the method considered for the conceptual design of both the production line and the overall layout of the KAPF process equipment. This study has proposed a design methodology that can be utilized as a preliminary step for the design of a hot-cell-type, large-scale facility, in which the various types of processing equipment operated by the remote handling system are integrated. The proposed methodology applies to part of the overall design procedure and contains various weaknesses. However, if the designer is required to maximize the efficiency of the installed material-handling system while considering operation restrictions and maintenance conditions, this kind of design process can accommodate the essential components that must be employed simultaneously in a general hot-cell system

Communications Received from Certain Member States Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology. Nuclear Transfers and Nuclear-Related Dual-Use Transfers

International Nuclear Information System (INIS)

1993-04-01

The Director General has received a Note Verbale dated 5 March 1993 from the Ministry of Foreign Affairs of the Slovak Republic. The purpose of the Note Verbale is to provide information on that Governments' guidelines for Nuclear Transfers and for Transfers of of Nuclear-related Dual-use Equipment, Material and Related Technology. In the light of the wish expressed at the end of each Note Verbale, the text of the Note Verbale is annexed hereto [fr

Communications Received from Certain Member States Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology. Nuclear Transfers and Nuclear-Related Dual-Use Transfers

International Nuclear Information System (INIS)

1993-04-01

The Director General has received a Note Verbale dated 5 March 1993 from the Ministry of Foreign Affairs of the Slovak Republic. The purpose of the Note Verbale is to provide information on that Governments' guidelines for Nuclear Transfers and for Transfers of of Nuclear-related Dual-use Equipment, Material and Related Technology. In the light of the wish expressed at the end of each Note Verbale, the text of the Note Verbale is annexed hereto [es

Energy Design Guidelines for High Performance Schools: Hot and Humid Climates

Energy Technology Data Exchange (ETDEWEB)

2002-06-01

School districts around the country are finding that the smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create and exemplary building that is both energy and resource efficient.

Energy Design Guidelines for High Performance Schools: Temperate and Humid Climates

Energy Technology Data Exchange (ETDEWEB)

2002-06-01

School districts around the country are finding that the smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create and exemplary building that is both energy and resource efficient.

Energy Design Guidelines for High Performance Schools: Temperate and Mixed Climates

Energy Technology Data Exchange (ETDEWEB)

2002-06-01

School districts around the country are finding that the smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create and exemplary building that is both energy and resource efficient.

Energy Design Guidelines for High Performance Schools: Cold and Humid Climates

Energy Technology Data Exchange (ETDEWEB)

2002-06-01

School districts around the country are finding that the smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create and exemplary building that is both energy and resource efficient.

Energy Design Guidelines for High Performance Schools: Cool and Dry Climates

Energy Technology Data Exchange (ETDEWEB)

2002-06-01

School districts around the country are finding that the smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create and exemplary building that is both energy and resource efficient.

Energy Design Guidelines for High Performance Schools: Hot and Dry Climates

Energy Technology Data Exchange (ETDEWEB)

2002-01-01

School districts around the country are finding that smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create an exemplary building that is both energy and resource efficient.

Energy Design Guidelines for High Performance Schools: Cool and Humid Climates

Energy Technology Data Exchange (ETDEWEB)

2002-06-01

School districts around the country are finding that the smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create and exemplary building that is both energy and resource efficient.

Communications received from Member States regarding guidelines for the export of nuclear material, equipment and technology

International Nuclear Information System (INIS)

1994-11-01

The Director General has received notes verbales relating to the export of nuclear material, equipment and technology from the following Permanent Missions to the International Atomic Energy Agency: notes verbales dated 15 June 1994 from the Permanent Missions of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, Luxembourg, Netherlands, Norway, Poland, Portugal, Romania, the Slovak Republic, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland and the United States of America; and a note verbale dated 10 November 1994 from the Permanent Mission of the Russian Federation. The purpose of these notes verbales is to provide further information on these Governments' nuclear export policies and practices. In the light of the wish expressed at the end of each note verbale, the analogous text of the notes verbales is attached hereto. The enclosure of these notes verbales with the amendments to the ''Guidelines for Nuclear Transfers'' contained in INFCIRC/254/Rev.1/Part 1/Mod.1 is reproduced in the Annex

Communication received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology. Nuclear transfers

International Nuclear Information System (INIS)

1995-10-01

The Director General has received notes verbales dated 30 June 1995 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, Luxembourg, the Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to the export of nuclear material, equipment and technology. The purpose of the notes verbales is to provide further information on those Governments' Guidelines for Nuclear Transfers. In the light of the wish expressed at the end of each note verbale, the text of the notes verbales is annexed hereto. The enclosure to these notes verbales is also reproduced in full in the Annex

Communication received from certain Member States regarding guidelines for the export of nuclear material, equipment and technology. Nuclear transfers

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-10-01

The Director General has received notes verbales dated 30 June 1995 from the Resident Representatives to the Agency of Argentina, Australia, Austria, Belgium, Bulgaria, Canada, the Czech Republic, Denmark, Finland, France, Germany, Greece, Hungary, Ireland, Italy, Japan, Luxembourg, the Netherlands, New Zealand, Norway, Poland, Portugal, Romania, the Slovak Republic, South Africa, Spain, Sweden, Switzerland, the United Kingdom of Great Britain and Northern Ireland, and the United States of America relating to the export of nuclear material, equipment and technology. The purpose of the notes verbales is to provide further information on those Governments` Guidelines for Nuclear Transfers. In the light of the wish expressed at the end of each note verbale, the text of the notes verbales is annexed hereto. The enclosure to these notes verbales is also reproduced in full in the Annex.

Development of the graphic design and control system based on a graphic simulator for the spent fuel dismantling equipment

Energy Technology Data Exchange (ETDEWEB)

Lee, J. Y.; Kim, S. H.; Song, T. G.; Yoon, J. S

2000-06-01

In this study, the graphic design system is developed for designing the spent fuel rod consolidation and the dismantling processes. This system is used throughout the design stages from the conceptual design to the motion analysis. Also, the real-time control system of the rod extracting equipment is developed. This system utilizes the graphic simulator which simulates the motion of the equipment in real time by synchronously connecting the control PC with the graphic server through the TCP/IP network. The developed system is expected to be used as an effective tool in designing the process equipment for the spent fuel management. And the real-time graphic control system can be effectively used to enhance the reliability and safety of the spent fuel handling process by providing the remote monitoring function of the process.

Development of the graphic design and control system based on a graphic simulator for the spent fuel dismantling equipment

International Nuclear Information System (INIS)

Lee, J. Y.; Kim, S. H.; Song, T. G.; Yoon, J. S.

2000-06-01

In this study, the graphic design system is developed for designing the spent fuel rod consolidation and the dismantling processes. This system is used throughout the design stages from the conceptual design to the motion analysis. Also, the real-time control system of the rod extracting equipment is developed. This system utilizes the graphic simulator which simulates the motion of the equipment in real time by synchronously connecting the control PC with the graphic server through the TCP/IP network. The developed system is expected to be used as an effective tool in designing the process equipment for the spent fuel management. And the real-time graphic control system can be effectively used to enhance the reliability and safety of the spent fuel handling process by providing the remote monitoring function of the process

Decreasing spatial disorientation in care-home settings: How psychology can guide the development of dementia friendly design guidelines.

Science.gov (United States)

O'Malley, Mary; Innes, Anthea; Wiener, Jan M

2017-04-01

Alzheimer's disease results in marked declines in navigation skills that are particularly pronounced in unfamiliar environments. However, many people with Alzheimer's disease eventually face the challenge of having to learn their way around unfamiliar environments when moving into assisted living or care-homes. People with Alzheimer's disease would have an easier transition moving to new residences if these larger, and often more institutional, environments were designed to compensate for decreasing orientation skills. However, few existing dementia friendly design guidelines specifically address orientation and wayfinding. Those that do are often based on custom, practice or intuition and not well integrated with psychological and neuroscientific knowledge or navigation research, therefore often remaining unspecific. This paper discusses current dementia friendly design guidelines, reports findings from psychological and neuropsychological experiments on navigation and evaluates their potential for informing design guidelines that decrease spatial disorientation for people with dementia.

Guideline for the seismic technical evaluation of replacement items for nuclear power plants

International Nuclear Information System (INIS)

Harris, S.P.; Cushing, R.W.; Johnson, H.W.; Abeles, J.M.

1993-02-01

Seismic qualification for equipment originally installed in nuclear power plants was typically performed by the original equipment suppliers or manufactures (OES/OEM). Many of the OES/OEM no longer maintain quality assurance programs with adequate controls for supplying nuclear equipment. Utilities themselves must provide reasonable assurance in the continued seismic adequacy of such replacement items. This guideline provides practical, cost-effective techniques which can be used to provide reasonable assurance that replacement items will meet seismic performance requirements necessary to maintain the seismic design basis of commercial nuclear power plants. It also provides a method for determining when a seismic technical evaluation of replacement items (STERI) is required as part of the procurement process for spare and replacement items. Guidance on supplier program requirements necessary to maintain continued seismic adequacy and on documentation of maintaining required seismic adequacy is also included

Survey and analysis on environmental and electromagnetic effect on instrumentation and control equipment of nuclear power plants

Energy Technology Data Exchange (ETDEWEB)

Hwang, In Koo; Lee, Dong Young; Cha, Kyung Ho

2001-03-01

As the instrumentation and control (I and C) equipment suppliers tend to provide digital components rather than conventional analog type components for instrumentation and control systems of nuclear power plants(NPPs), it is unavoidable to adopt digital equipment for safety I and C systems as well as non-safety systems. However, the full introduction of digital equipment for I and C systems of nuclear power plants raises several concerns which have not been considered in conventional analog I and C equipment. The two major examples of the issues of digital systems are environmental/electromagnetic compatibility (EMC) and software reliability. This report presents the survey and research results on environmental and electromagnetic effect on I and C equipment of nuclear power plants to give a guideline for aging management and design process. Electromagnetic site surveys were conducted to be used as a part of technical basis to demonstrate that I and C systems are compatible with the ambient electromagnetic noise in Korean nuclear power plants.

Development of safety and regulatory requirements for Korean next generation reactor - Development of human factors design review guidelines (II)

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Oh, In Suk; Lee, Hyun Chul; Cheon, Se Woo [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-02-01

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: '25. Human Factors Engineering Program Review Model' and '26. Review Criteria for Human Factors Aspects of Advanced Controls and Instrumentation', which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and the characteristics of the KNGR design, and reviewing the reference documents of NURGE-0711. We also computerized the Korean version of NUREG-0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides at KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system design review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm systems. Then we updated the guidelines by reviewing the literature related to alarm design that published after 1994. 12 refs., 11 figs., 2 tabs. (Author)

Development of safety and regulatory requirements for Korean next generation reactor - Development of human factors design review guidelines (II)

Energy Technology Data Exchange (ETDEWEB)

Lee, Jung Woon; Oh, In Suk; Lee, Hyun Chul; Cheon, Se Woo [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-02-01

The objective of this study is to develop human factors engineering program review guidelines and alarm system review guidelines in order to resolve the two major technical issues: '25. Human Factors Engineering Program Review Model' and '26. Review Criteria for Human Factors Aspects of Advanced Controls and Instrumentation', which are related to the development of human factors safety regulation guides being performed by KINS. For the development of human factors program review guidelines, we made a Korean version of NUREG-0711 and added our comments by considering Korean regulatory situation and the characteristics of the KNGR design, and reviewing the reference documents of NURGE-0711. We also computerized the Korean version of NUREG-0711, additional comments, and selected portion of the reference documents for the developer of safety regulation guides at KINS to see the contents comparatively at a glance and use them easily. For the development of alarm system design review guidelines, we made a Korean version of NUREG/CR-6105, which was published by NRC in 1994 as a guideline document for the human factors review of alarm systems. Then we updated the guidelines by reviewing the literature related to alarm design that published after 1994. 12 refs., 11 figs., 2 tabs. (Author)

Seismic qualification of equipment in operating nuclear power plants: Unresolved Safety Issue A-46

International Nuclear Information System (INIS)

Chang, T.Y.

1987-02-01

The margin of safety provided in existing nuclear power plant equipment to resist seismically induced loads and perform their intended safety functions may vary considerably, because of significant changes in design criteria and methods for the seismic qualification of equipment over the years. Therefore, the seismic qualification of equipment in operating plants must be reassessed to determine whether requalification is necessary. The objective of technical studies performed under the Task Action Plan A-46 was to establish an explicit set of guidelines and acceptance criteria to judge the adequacy of equipment under seismic loading at all operating plants, in lieu of requiring qualification to the current criteria that are applied to new plants. This report summarizes the work accomplished on USI A-46. In addition, the collection and review of seismic experience data and existing seismic test data are presented. Staff assessment of work accomplished under USI A-46 leads to the conclusion that the use of seismic experience data provides the most reasonable alternative to current qualification criteria. Consideration of seismic qualification by use of experience data was a specific task in USI A-46. Several other A-46 tasks serve to support the use of an experienced data base. The principal technical finding of USI A-46 is that seismic experience data, supplemented by existing seismic test data, applied in accordance with the guidelines developed, can be used to verify the seismic adequacy of mechanical and electrical equipment in operating nuclear plants. Explicit seismic qualification should be required only if seismic experience data or existing test data on similar components cannot be shown to apply

Lists A and B of X-ray equipment. As of July 1, 1984

International Nuclear Information System (INIS)

1984-01-01

The lists A and B of X-ray equipment present the guidelines for X-ray device, as of December 10, 1983, that are defined in the guidelines for radiology and nuclear medicine of the Federal Association of Panel Doctors. In list A, the equipment categories of up-to-date, commercially available X-ray device are given, whereas list B classifies older equipment, both types available from manufacturers who are members of the ZVEI association. Since the categories of application II and III have been made, specifiying the equipment still in use and applicable within a given transitional period in existing medical establishments, but which may not be applied in new establishments. The list of manufacturers gives the addresses of the firms supplying the equipment described in Lists A and B, which have been compiled according to the requirements set by the Federal Association of Panel Doctors. (orig.) [de

Design of inspection equipment vehicle of mobile cobalt-60 container scanner

International Nuclear Information System (INIS)

Zhang Yanmin; An Jigang; Zhou Liye; Liu Yisi; Wu Zhifang; Xiang Xincheng; Huang Songling

2000-01-01

The author introduced the design principle of Inspection Equipment Vehicle of TCM-SCAN Mobile 60 Co container inspection system. Three schemes had been compared. The scheme of scan gate in form of pucker-able rails standing on the vehicle was determined. Prototype was prepared in September 1999. Mobile 60 Co container inspection system had the same inspection performance of fixed 60 Co container inspection system

Communications Received from Certain Member States Regarding Guidelines for the Export of Nuclear Material, Equipment and Technology. Nuclear Transfers and Nuclear-Related Dual-Use Transfers

International Nuclear Information System (INIS)

1993-04-01

The Director General has received a Note Ver bale dated 5 March 1993 from the Ministry of Foreign Affairs of the Slovak Republic. The purpose of the Note Ver bale is to provide information on that Governments' guidelines for Nuclear Transfers and for Transfers of of Nuclear-related Dual-use Equipment, Material and Related Technology. In the light of the wish expressed at the end of each Note Ver bale, the text of the Note Ver bale is annexed hereto

Strategies for replacement of obsolete equipment - including reverse engineering

International Nuclear Information System (INIS)

Irish, C.S.

2000-01-01

The presentation shall detail the challenges facing nuclear power plants with the replacement of obsolete equipment and the strategies used to overcome those challenges. The presentation will outline the common equipment types which are either obsolete or are becoming obsolete, with a focus on safety related components. The four options of the obsolete equipment replacement philosophy will be presented with replacement examples from each of the options shown for discussion purposes. Detailed examples from each of the four obsolete equipment replacement options of: commercially available equivalent component; modification of a commercial available component; reverse engineering of the original component; and finally, design changes using a new component, shall be presented to evaluate the advantages and disadvantages of each option. The presentation will include the technical challenges, cost and schedule concerns for each of the four options. Emphasis will be placed on the technological challenges associated with replacing old and obsolete equipment. The following is a bullet list of the challenges which will be discussed: Missing, misleading or no information on the original component; Acquiring information from the original equipment manufacturer and the plant; Using a sample component for the replacement evaluation and or reverse engineering; and Reverse engineering old equipment with newly available discrete components. The presentation will include the equivalency documentation using the EPRI guidelines when replacing an original component with a different yet form, fit and functional equivalent component. The presentation will conclude with a discussion of the advantages and disadvantages of the replacement of the obsolete component with a form, fit and functional equivalent component vs. the replacement of the original component with a new component with today's technology. (author)

Designing an automated clinical decision support system to match clinical practice guidelines for opioid therapy for chronic pain

Directory of Open Access Journals (Sweden)

Clark Michael E

2010-04-01

Full Text Available Abstract Background Opioid prescribing for chronic pain is common and controversial, but recommended clinical practices are followed inconsistently in many clinical settings. Strategies for increasing adherence to clinical practice guideline recommendations are needed to increase effectiveness and reduce negative consequences of opioid prescribing in chronic pain patients. Methods Here we describe the process and outcomes of a project to operationalize the 2003 VA/DOD Clinical Practice Guideline for Opioid Therapy for Chronic Non-Cancer Pain into a computerized decision support system (DSS to encourage good opioid prescribing practices during primary care visits. We based the DSS on the existing ATHENA-DSS. We used an iterative process of design, testing, and revision of the DSS by a diverse team including guideline authors, medical informatics experts, clinical content experts, and end-users to convert the written clinical practice guideline into a computable algorithm to generate patient-specific recommendations for care based upon existing information in the electronic medical record (EMR, and a set of clinical tools. Results The iterative revision process identified numerous and varied problems with the initially designed system despite diverse expert participation in the design process. The process of operationalizing the guideline identified areas in which the guideline was vague, left decisions to clinical judgment, or required clarification of detail to insure safe clinical implementation. The revisions led to workable solutions to problems, defined the limits of the DSS and its utility in clinical practice, improved integration into clinical workflow, and improved the clarity and accuracy of system recommendations and tools. Conclusions Use of this iterative process led to development of a multifunctional DSS that met the approval of the clinical practice guideline authors, content experts, and clinicians involved in testing. The

Study for process and equipment design of wet gelation stages in vibropacking process

International Nuclear Information System (INIS)

Tanimoto, Ryoji; Kikuchi, Toshiaki; Tanaka, Hirokazu; Amino, Masaki; Yanai, Minoru

2004-02-01

Process and layout design of external wet gelation stages in vibropacking process was examined for the feasibility study of commercialized FBR cycle system. In this study, following process stages for the oxide core fuel production line were covered, that is, solidification, washing, drying, calcination, reduction, sintering stages including interim storage of sintering particles and reagent recovery stage. The main results obtained by this study are as follows: (1) Based on the process examination results conducted previously, process-flow, mass-balance and number of production line/equipment were clarified. The process is covered from the receive tank of feed solution to the interim storage equipment. Reagent recovery process-flow, mass-balance were also clarified. And preliminary design of the main equipment was reexamined. (2) Normal operation procedure and the procedure after process failure were summarized along with a remote automated operation procedure. Operation sequence of each production line was mapped out by using a time-chart. (3) Design outline of reagent recovery equipments, installed to recover waste liquid from the wet gelation stages in the view of environmental impact were examined. Effective techniques such as collection of solvent, residue waste treatment method were examined its applicability and selected. Schematic block diagram was presented. (4) Analytical items and analyzing apparatus were extracted taking into account of quality control and process management. Analytical sample taking position and frequency of sampling were also examined. (5) A schematic layout drawing of main manufacturing process and reagent recovery process was presented taking into account of material handling. (6) A feature of the operating rate at each process stage was examined by analyzing failure rate reliability of each component. applying the reliability-centred method. (RCM), the operating rate was evaluated and annual maintenance period was estimated using

Quality assurance in radiotherapy: Proposal of guidelines concerning clinical and technological aspects

International Nuclear Information System (INIS)

Group of study 'Assicurazione di qualita' in radioterapia'.

1996-12-01

The document, based on European guidelines, was jointly developed by radiation oncologists, radiation physicists and radiation technologists. In contains the aims of the guidelines, professional profiles, roles and responsibilities, personnel and equipment requirements, procedures

Safety code 19: recommended safety procedures for the selection, installation and use of x-ray diffraction equipment

International Nuclear Information System (INIS)

1984-01-01

This document is one of a series of Safety Codes prepared by the Radiation Protection Bureau to set out requirements for the safe use of radiation emitting devices. The equipment and installation guidelines and safety procedures detailed in this Code are primarily for the instruction and guidance of persons employed in Federal Public Service Departments and Agencies, as well as those coming under the jurisdiction of the Canada Labour Code. This Safety Code is also intended to assist other users of X-ray diffraction equipment to select safe equipment and to install and use it so that the radiation hazard to the operator and other persons in its vicinity is negligible. It should be noted that facilities under provincial jurisdiction may be subject to requirements specified under provincial statutes. This Code supersedes Safety Code RPD-SC-7, entitled 'Requirements For Non-Medical X-Ray Equipment, Use and Installation', insofar as X-ray diffraction equipment is concerned, and it is intended to complement X-ray equipment design, construction and performance standards promulgated under the Radiation Emitting Devices Act

Passive solar design strategies: Remodeling guidelines for conserving energy at home. [Final report

Energy Technology Data Exchange (ETDEWEB)

1991-12-31

The idea of passive solar is simple, but applying it effectively does require information and attention to the details of design and construction. Some passive solar techniques are modest and low-cost, and require only small changes in remodeler`s typical practice. At the other end of the spectrum, some passive solar systems can almost eliminate a house`s need for purchased heating (and in some cases, cooling) energy -- but probably at a relatively high first cost. In between are a broad range of energy-conserving passive solar techniques. Whether or not they are cost-effective, practical and attractive enough to offer a market advantage to any individual remodeler depends on very specific factors such as local costs, climate, and market characteristics. Passive solar design strategies: Remodeling Guidelines For Conserving Energy At Homes is written to help give remodelers the information they need to make these decisions. Passive Solar Design Strategies is a package in three basic parts: The Guidelines contain information about passive solar techniques and how they work, and provides specific examples of systems which will save various percentages of energy; The Worksheets offer a simple, fill-in-the-blank method to pre-evaluate the performance of a specific design; The Worked Example demonstrates how to complete the worksheets for a typical residence.

Human-system interface design review guideline -- Review software and user's guide: Final report. Revision 1, Volume 3

International Nuclear Information System (INIS)

1996-06-01

NUREG-0700, Revision 1, provides human factors engineering (HFE) guidance to the US Nuclear Regulatory Commission staff for its: (1) review of the human system interface (HSI) design submittals prepared by licensees or applications for a license or design certification of commercial nuclear power plants, and (2) performance of HSI reviews that could be undertaken as part of an inspection or other type of regulatory review involving HSI design or incidents involving human performance. The guidance consists of a review process and HFE guidelines. The document describes those aspects of the HSI design review process that are important to the identification and resolution of human engineering discrepancies that could adversely affect plant safety. Guidance is provided that could be used by the staff to review an applicant's HSI design review process or to guide the development of an HSI design review plan, e.g., as part of an inspection activity. The document also provides detailed HFE guidelines for the assessment of HSI design implementations. NUREG-0700, Revision 1, consists of three stand-alone volumes. Volume 3 contains an interactive software application of the NUREG-0700, Revision 1 guidance and a user's guide for this software. The software supports reviewers during review preparation, evaluation design using the human factors engineering guidelines, and in report preparation. The user's guide provides system requirements and installation instructions, detailed explanations of the software's functions and features, and a tutorial on using the software

Global Imaging referral guidelines

International Nuclear Information System (INIS)

Kawooya, M.; Perez, M.; Lau, L.; Reeed, M.

2010-01-01

The medical imaging specialists called for global referral guidelines which would be made available to referring doctors. These referral guidelines should be:- Applicable in different health care settings, including resource-poor settings; Inclusive in terms of the range of clinical conditions; User-friendly and accessible (format/media); Acceptable to stakeholders, in particular to the referrers as the main target audience. To conceive evidence-based medicine as an integration of best research evidence with clinical expertise and patient values. The Direct recipients of the Referral Guidelines would be:- Referrers: general practitioners / family doctors; paediatricians; emergency department doctors; other specialists and health workers. Providers (medical imaging practitioners): radiologists; nuclear medicine physicians; radiographers; other appropriately qualified practitioners providing diagnostic imaging services. For the Referral Guidelines to be effective there need to be: Credibility evidence-based Practicality end user involvement Context local resources, disease profiles Endorsement, opinion leaders Implementation- policy, education, CPOE - Monitoring of the use clinical audit, report feedback. The aim of the Referral Guidelines Project was to: Produce global referral guidelines that are evidence-based, cost effective and appropriate for the local setting, and include consideration of available equipment and expertise (RGWG; SIGs); Include supporting information about radiation doses, potential risks, protection of children and pregnant women (introductory chapter); Facilitate the implementation of the guidelines through guidance and tools (e.g. implementation guides, checklists, capacity building tools, guides on stakeholders engagement, audit support criteria); Conduct pilot testing in different clinical settings from each of the six WHO regions; Promote the inclusion of the referral guidelines in the curricula of medical schools; Develop and implement

Flight critical system design guidelines and validation methods

Science.gov (United States)

Holt, H. M.; Lupton, A. O.; Holden, D. G.

1984-01-01

Efforts being expended at NASA-Langley to define a validation methodology, techniques for comparing advanced systems concepts, and design guidelines for characterizing fault tolerant digital avionics are described with an emphasis on the capabilities of AIRLAB, an environmentally controlled laboratory. AIRLAB has VAX 11/750 and 11/780 computers with an aggregate of 22 Mb memory and over 650 Mb storage, interconnected at 256 kbaud. An additional computer is programmed to emulate digital devices. Ongoing work is easily accessed at user stations by either chronological or key word indexing. The CARE III program aids in analyzing the capabilities of test systems to recover from faults. An additional code, the semi-Markov unreliability program (SURE) generates upper and lower reliability bounds. The AIRLAB facility is mainly dedicated to research on designs of digital flight-critical systems which must have acceptable reliability before incorporation into aircraft control systems. The digital systems would be too costly to submit to a full battery of flight tests and must be initially examined with the AIRLAB simulation capabilities.

Residential neighbourhoods in Kathmandu: Key design guidelines

Directory of Open Access Journals (Sweden)

Bijaya K. Shrestha

2013-01-01

Full Text Available Residential neighbourhoods developed using various techniques in Kathmandu by both the public and private sectors have not only provided a poor urban setting and failed to address socio-cultural needs, but are also poor at building a community and creating links to the built environment, with the result that the planned areas lack a sense of place and the inhabitants lack a feeling of home. Although traditional neighbourhoods in the historic core area had many features of a good residential neighbourhood in the past, they are currently undergoing rapid destruction. The residents of these neighbourhoods have little awareness of these issues. The existing legal and institutional frameworks are inadequate and ineffective and cannot address these problems, and so the formulation of design guidelines, their strict implementation, and enhancement of socio-cultural events including social networking are recommended for future residential neighbourhood development.

The Design and Experiment of the Track-Type Equipment for Feeding Dairy Cows

Directory of Open Access Journals (Sweden)

Yaping LI

2014-06-01

Full Text Available As one of the effective ways of reducing the cost and increase the revenue, feeding dairy cows with individual precision in quantity could further develop the production potential of high- yield dairy cows and improve the milk yield of every dairy cow. Therefore, based on three kinds of technologies of radio frequency identification technology, wireless transmission technology and infrared technology and grounded on the foundation of previous studies, this thesis has completed the track- type equipment for feeding dairy cows with individual precision in quantity. The equipment takes the computer as the information management platform, adopts the singly chip microcomputer as the control platform, uses the wireless module and U disk to conduct the transmission of individual feeding data of dairy cows and guides the whole process with the track. This kind of equipment could advance automatically, identify and feed dairy cows precisely during the feeding process. This thesis also designs the matching feeding technology of the equipment, and accomplishes the test of feeding outside the cowshed, which takes “TMR + precise feeding with concentrated feed” as the feeding model, so that the feeding process could be more effective and further steady.

Localization of equipment for digital plant protection system

Energy Technology Data Exchange (ETDEWEB)

Koo, I. S.; Park, H. Y.; Lee, C. K. and others

2000-10-01

The objective of this project lies on the development of design requirements, establishment of structure and manufacture procedures, development of the software verification and validation(V and V) techniques of the digital plant protection system. The functional requirements based on the analog protection system and digital design requirements are introduced, the processor and system bus for safety grade equipment are selected and the interface requirements and the design specification have been developed in order to manufacture the quick prototype of the digital plant protection system. The selection guidelines of parts, software development and coding and testing for digital plant protection system have been performed through manufacturing the quick prototype based on the developed design specification. For the software verification and validation, the software review plan and techniques of verification and validation have been researched. The digital validation system is developed in order to verify the quick prototype. The digital design requirements are reviewed by the software safety plan and V and V plans. The formal methods for verifying the safety-grade software are researched, then the methodology of formal analysis and testing have been developed.

Localization of equipment for digital plant protection system

International Nuclear Information System (INIS)

Koo, I. S.; Park, H. Y.; Lee, C. K. and others

2000-10-01

The objective of this project lies on the development of design requirements, establishment of structure and manufacture procedures, development of the software verification and validation(V and V) techniques of the digital plant protection system. The functional requirements based on the analog protection system and digital design requirements are introduced, the processor and system bus for safety grade equipment are selected and the interface requirements and the design specification have been developed in order to manufacture the quick prototype of the digital plant protection system. The selection guidelines of parts, software development and coding and testing for digital plant protection system have been performed through manufacturing the quick prototype based on the developed design specification. For the software verification and validation, the software review plan and techniques of verification and validation have been researched. The digital validation system is developed in order to verify the quick prototype. The digital design requirements are reviewed by the software safety plan and V and V plans. The formal methods for verifying the safety-grade software are researched, then the methodology of formal analysis and testing have been developed

Guidelines for testing sealed radiation sources

International Nuclear Information System (INIS)

1989-01-01

These guidelines are based on article 16(1) of the Ordinance on the Implementation of Atomic Safety and Radiation Protection dated 11 October 1984 (VOAS), in connection with article 36 of the Executory Provision to the VOAS, of 11 October 1984. They apply to the testing of sealed sources to verify their intactness, tightness and non-contamination as well as observance of their fixed service time. The type, scope and intervals of testing as well as the evaluation of test results are determined. These guidelines also apply to the testing of radiation sources forming part of radiation equipment, unless otherwise provided for in the type license or permit. These guidelines enter into force on 1 January 1990

The users centered design of a new digital fluorometer

International Nuclear Information System (INIS)

Farias, Marcos S.; Santos, Isaac J.A.L. dos; Grecco, Claudio H.S.; Pedrosa, Paulo S.; Colthurst, Carlos M.; Szabo, Andre P.

2009-01-01

The fluorometer is the equipment used in chemical analysis laboratories, research institutes and nuclear fuel cycle companies. This equipment measures an unknown amount of uranium in ores, rivers, etc. The fluorometer functioning is based on the uranium fluorescence when submitted to the ultraviolet radiation incidence. The fluorescence is measured by an electronic optic system with optics filters, photomultiplier tube, and a current amplifier. The user centered design involves the user in the product development in all phases of the design process. Users are not simply consulted at the beginning of the design process and evaluated the system at the end; they are treated as partners throughout the design process. The user centered design emphasizes the needs and abilities of the users and improves the usability of the equipment. The activity centered design emphasizes the development of the equipment with a deep understanding of the users activities and of the current work practices of the users. The aim of this paper is to present a methodological framework that contributes to the design and evaluation of a new digital fluorometer towards an approach related to the users and their activities. This methodological framework includes users-based testing, interviews, questionnaires, human factors standards and guidelines, the users activity analysis and users satisfaction questionnaire. (author)

Energy Design Guidelines for High Performance Schools: Hot and Dry Climates (Revision)

Energy Technology Data Exchange (ETDEWEB)

2002-06-01

School districts around the country are finding that the smart energy choices can help them save money and provide healthier, more effective learning environments. By incorporating energy improvements into their construction or renovation plans, schools can significantly reduce energy consumption and costs. These savings can be redirected to educational needs such as additional teachers, instructional materials, or new computers. These design guidelines outline high performance principles for the new or retrofit design of your K-12 school. By incorporating these principles, you can create and exemplary building that is both energy and resource efficient.

Process and equipment design optimising product properties and attributes

NARCIS (Netherlands)

Bongers, P.M.M.; Thullie, J.

2009-01-01

Classically, when products have been developed at the bench, process engineers will search for equipment to manufacture the product at large scale. More than often, this search is constraint to the existing equipment base, or a catalog search for standard equipment. It is then not surprising, that

LMFBR safety criteria and guidelines for consideration in the design of future plants

International Nuclear Information System (INIS)

1990-01-01

For many years the Commission of the European Communities has been conducting activities aimed at the progressive harmonization of safety requirements and criteria applied to nuclear installations in the Community. These activities cover thermal and fast reactors. This publication represents a major achievement in reaching this goal. The document, which has been prepared in the framework of activities of the CEC fast-reactor safety working group (SWG), consists of safety criteria and guidelines for fast reactors. It represents the common view of all EC Member States which have a fast-reactor programme or are interested in fast-reactor development. The criteria and guidelines are structured according to different types of possible faults, such as core reactivity faults, general cooling faults, subassembly faults, faults outside the core and causes external to the station. Only those events are considered which are in the design basis of current fast-reactor projects. Proposed measures or guidelines to satisfy the criteria are based on the present knowledge and proven technology

Availability of Life Support Equipment and its Utilization by Ambulance Drivers.

Science.gov (United States)

Acharya, Rija; Badhu, Angur; Shah, Tara; Shrestha, Sharmila

2017-09-08

An effective ambulance is a vital requirement for providing an emergency medical service. Well-equipped ambulances with trained paramedics can save many lives during the golden hours of trauma care. The objective was to document the availability and utilization of basic life support equipment in the ambulances and to assess knowledge on first aid among the drivers. Descriptive design was used. Total of 109 ambulances linked to B.P. Koirala Institute of Health Sciences were enrolled using purposive sampling method. Self- constructed observation checklist and semi structured interview schedule was used for data collection. More than half of the respondents had less than five years of experience and were not trained in first aid. About two-third of the respondents had adequate knowledge on first aid. About 90% of the ambulance had oxygen cylinder and adult oxygen mask which was 'usually' used equipment. More than half of ambulance had equipment less than 23% as compared to that of national guidelines. There was significant association of knowledge with the experience (p = 0.004) and training (p = 0.001). Availability of equipment was associated with training received (p = 0.007),organization (p= 0.032)and district (p = 0.023) in which the ambulance is registered. The study concludes that maximum ambulance linked to BPKIHS, Nepal did not have even one fourth of the equipment for basic life support. Equipment usually used was oxygen cylinder and oxygen mask. Majority of driver had adequate knowledge on first aid and it was associated with training and experience.

Strategies for replacement of obsolete equipment, including reverse engineering

International Nuclear Information System (INIS)

Irish, C.S.

2003-01-01

The presentation shall detail the challenges facing nuclear power plants with the replacement of obsolete equipment and the strategies used to overcome those challenges. The presentation will outline the common equipment types which are either obsolete or are becoming obsolete, with a focus on safety related components. The four options of the obsolete equipment replacement philosophy will be presented with replacement examples from each of the options shown for discussion purposes. Detailed examples from each of the four obsolete equipment replacement options of, (1) commercially available equivalent component, (2) modification of a commercial available component, (3) reverse engineering of the original component and finally (4) design changes using a new component, shall be presented to evaluate the advantages and disadvantages of each option. The presentation will include the technical challenges, cost and schedule concerns for each of the four options. Emphasis will be placed on the technological challenges associated with replacing old and obsolete equipment. The following is a bullet list of the challenges which will be discussed: 1) Missing, misleading or no information on the original component. 2) Acquiring information from the original equipment manufacturer and the plant. 3) Using a sample component for the replacement evaluation and or reverse engineering. 4) Reverse engineering old equipment with newly available discrete components. The presentation will include the equivalency documentation using the EPRI guidelines when replacing an original component with a different yet form, fit and functional equivalent component. The presentation will conclude with a discussion of the advantages and disadvantages of the replacement of the obsolete component with a form, fit and functional equivalent component vs. the replacement of the original component with a new component with today's technology. (author)

Colour Size Illusion on Liquid Crystal Displays and Design Guidelines for Bioinformatics Tools

Science.gov (United States)

Yoo, Hyun Seung; Smith-Jackson, Tonya L.

2011-01-01

Although the influence of colour on size perception has been known for a century, there is only limited research on interventions that can reduce this effect. This study was therefore undertaken in order to identify appropriate interventions and propose design guidelines for information visualisation, especially in applications where size…

Design considerations for teleoperation systems operating in gas-tight argon cells

Directory of Open Access Journals (Sweden)

Seungnam Yu

2017-12-01

Full Text Available In the nuclear industry, mechanical engineers spend a significant portion of their time designing equipment such as manipulators, bogies, mechanical grippers, and so on. Some customized designs can be considered as standard mechanical equipment in this area, although it is not unusual to find that an existing design cannot simply be copied from one project to another. Varied performance requirements can dictate that redesign, often quite extensive redesign, is required. However, if something similar has been done before, engineers could use that as a starting point for the new project. In this regard, this study presents several guidelines inspired by previous design knowledge for similar development cases. Moreover, this study presents more detailed suggestions such as design guidelines for an argon-based hot cell atmosphere and design experience for a large-scale practical hot cell facility. Design considerations and case studies dealt with in this study are dedicated to teleoperation manipulators that are used at a large-scale argon cell facility for pyroprocess integrated inactive demonstration (PRIDE, at the Korea Atomic Energy Research Institute. In particular, for case studies to support the suggested recommendations, a fabricated telemanipulator system for PRIDE is introduced, and several kinds of experimental results associated with it are presented.

Prototypical spent fuel rod consolidation equipment preliminary design report: Volume 1, Report

International Nuclear Information System (INIS)

1986-01-01

This design report describes the NUS Preliminary Design of the Prototype Spent Nuclear Fuel Rod Consolidation Equipment for the Department of Energy. The sections of the report elaborate on each facet of the preliminary design. A concept summary is provided to assist the reader in rapidly understanding the complete design. The NUS Prototype Spent Fuel Rod Consolidation System is an automatically controlled system to consolidate a minimum of 750 MT (heavy metal)/year of US commercial nuclear reactor fuel, at 75% availability. The system is designed with replaceable components utilizing the latest state-of-the-art technology. This approach gives the system the flexibility to be developed without costly development programs, yet accept new technology as it evolves over the next ten years. Capability is also provided in the system design to accommodate a wide variety of fuel conditions and to recover from any situation which may arise

Design as if people matter: aesthetic guidelines for the wind industry

International Nuclear Information System (INIS)

Gipe, P.

1995-01-01

Opinion surveys show that wind has high public support, but a worrisome NIMBY factor. This support erodes once specific projects are proposed. Because support is fragile and can be squandered by ill-conceived projects, the industry must do everything it can to ensure that wind turbines and wind power plants become good neighbours. One means of maximizing acceptance is to incorporate aesthetic guidelines into the design of wind turbines and wind power plants. (Author)

Design and Construction of Equipment for Applying the Geophysical Prospecting Method Electric Tomography

Directory of Open Access Journals (Sweden)

Fabio Héctor Giraldo Sánchez

2013-06-01

Full Text Available Outlines the procedure for the design and construction of electric equipment for geophysical prospecting through electrical tomography method. The team is of average power, ensuring exploration depths quite suitable for applications and commercial and geotechnical studies. The device is essentially a DC voltage source of 500 volts that is able to provide a maximum current of 1 amp. It also contains a small charge current source of electrical currents counteract naturally found in the subsoil and are manifested as a difference in the surface potential. A general explanation of the geophysical method in question, helps to understand the basic principles of operation of the equipment and functions to be fulfilled. After building the team, we conducted a field data acquisition, in area near the town of Gachancipa Cundinamarca. The data from this equipment are processed with specialized software. The images obtained with the software presents the distributions of subsurface resistivity can be associated with the possible structures and geology of the study area.

On anti-earthquake design procedure of equipment and pipings in near future

International Nuclear Information System (INIS)

Shibata, H.

1981-01-01

The requirement of anti-earthquake design of nuclear power plants is getting severe year by year. The author will try to discuss how to control its severity and how to find a proper design procedure for licensing of new plants under such severe requirements. On the other hand we suffered from the enormous volumes of documents. To decrease such volumes, the format of documents should be standardized as well as the design procedure standardization. Starting from this point, we need the research and development on the following subjects: i) Standardization of design procedure. ii) Standardization of document. iii) Establishment of standard review procedure using computer. iv) Standardization of earthquake-resistant designed equipment. v) Standardization of anti-earthquake design procedure of piping systems. vi) Introducing margin evaluation procedure to design procedure. vii) Introducing proving test procedure of active component to design procedure. viii) Establishment of evaluation of human reliability in design, fabrication, inspection procedures. ix) Establishment of the proper relation of seismic trigger level and post-earthquake design procedures. (orig./HP)

[Guidelines for management of epilepsy--commentary on Scottish ("SIGN") guidelines].

Science.gov (United States)

Planjar-Prvan, Miljenka; Granić, Davorka

2005-01-01

The choice of AED (antiepileptic drug), worldwide and in Croatia, is been still based on the physician's subjective decision, personal experience, knowledge and marketing pressure made by big pharmaceutical industries. Therefore, according to some opinions, there is a need of treatment guidelines for epilepsy that would provide relevant information based on scientific evidence on the efficacy, tolerability and safety of AEDs. The guidelines, published by a competent source, should be designed as to allow for easy access to the information on the best practice in specific cases. An extensive background literature review was made to identify such a type of guidelines for the management of epilepsy. The literature review revealed a number of references with the recommendations for treating epilepsy in different groups of patients and from various, specific aspects of epilepsy treatment. However, only one comprehensive set of guidelines for the diagnosis and treatment of epilepsy treatment was found, i.e. the evidence-based guidelines published by the Scottish Intercollegiate Guidelines Network (SIGN). The development of this set of guidelines is quite extensively described in order to illustrate how rigorous and long-lasting the process was, including a great number of health professionals at the national level. Such a type of well designed guidelines facilitates access to highest educational standards for all professionals involved in the primary and secondary care of people with epilepsy. However, it is clear that guidelines can fully replace the standards of clinical practice based on critical evaluation and integration of all clinical data of each individual patient. No guidelines can replace the physician's obligation to keep informed of the novel achievements in the epileptology either.

Revising the South African guidelines for human settlement planning and design (the red book)

CSIR Research Space (South Africa)

Van Niekerk, Willemien

2015-11-01

Full Text Available The Guidelines for Human Settlement Planning and Design, commonly known as the Red Book, is a South African publication aimed at providing practical guidance to built environment professionals in support of the creation of sustainable and vibrant...

Design and construction of stepper motor controller for brachy-therapy equipment

International Nuclear Information System (INIS)

Ahmad Rifai; Usep Setia Gunawan; Indarzah Masbatin Putra

2011-01-01

Based on a microcontroller, a stepper motor controller for brachy-therapy equipment has been designed and prototyped. The embedded control program routine and its other associated routines enable the microcontroller to generate required pulses via external commands for stepper motor based position control. The controller receives ASCII text command via a serial port. The constructed algorithm implements the widely used method that allows motor to rotate in three phases, i.e: acceleration, constant speed, and deceleration. (author)

Design and operation of equipment used to develop remote coating capability for HTGR fuel particles

International Nuclear Information System (INIS)

Suchomel, R.R.; Stinton, D.P.; Preston, M.K.; Heck, J.L.; Bolfing, B.J.; Lackey, W.J.

1978-12-01

Refabrication of HTGR fuels is a manufacturing process that consists of preparation of fuel kernels, application of multiple layers of pyrolytic carbon and silicon carbide, preparation of fuel rods, and assembly of fuel rods into fuel elements. All the equipment for refabrication of 233 U-containing fuel must be designed for completely remote operation and maintenance in hot-cell facilities. Equipment to remotely coated HTGR fuel particles has been designed and operated. Although not all of the equipment development needed for a fully remote coating system has been completed, significant progress has been made. The most important component of the coating furnace is the gas distributor, which must be simple, reliable, and easily maintainable. Techniques for loading and unloading the coater and handling microspheres have been developed. An engineering-scale system, currently in operation, is being used to verify the workability of these concepts. Coating crucible handling components are used to remove the crucible from the furnace, remove coated particles, and exchange the crucible, if necessary. After the batch of particles has been unloaded, it is transferred, weighed, and sampled. The components used in these processes have been tested to ensure that no particle breakage or holdup occurs. Tests of the particle handling system have been very encouraging because no major problems have been encountered. Instrumentation that controls the equipment performed very smoothly and reliably and can be operated remotely

WIPP conceptual design report. Addendum J. Support equipment in the high level waste facility of the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Rieb, M.J.; Foley, R.S.

1977-04-01

The Aerojet Manufacturing Company (AMCO) received a contract in November 1976 to provide consulting services in assisting Holmes and Narver, Incorporated with the conceptual designs, cost estimates, and schedules of equipment used to handle waste casks, to decontaminate waste canisters and to overpack damaged or highly contaminated waste canisters for the Waste Isolation Pilot Plant (WIPP). Also, the layout of the hot cell in which canister handling, overpack and decontamination takes place was to be reviewed along with the time and motion study of the cell operations. This report has been prepared to present the results of the efforts and contains all technical and planning data developed during the program. The contents of this report are presented in three sections: (1) comments on the existing design criteria, equipment conceptual designs, hot cell design and time and motion studies of projected hot cell activities; (2) design descriptions of the equipment concepts and justification for varying from the existing concept (if a variation occurred). Drawings of each concept are provided in Appendix A. These design descriptions and drawings were used as the basis for the cost estimates; and (3) schedule projections and cost estimates for the equipment described in Section 2. Detail cost estimate backup data is provided in Appendix B

Benefits of Digital Equipment Generic Qualification Activities

International Nuclear Information System (INIS)

Thomas, James E.; Steiman, Samuel C.

2002-01-01

As a result of nuclear power plant instrumentation and control obsolescence issues, there have been numerous activities during recent years relating to the qualification of digital equipment. Some of these activities have been 'generic' in nature in that the qualification was not limited to plant specific applications, but was intended to cover a broad base of potential applications of the digital equipment. These generic qualifications have been funded by equipment manufacturers and by utility groups and organizations. The generic activities sponsored by the Electric Power Research Institute (EPRI) have been pilot projects for an overall generic qualification approach. The primary benefit resulting from the generic qualification work to date is that a number of digital platforms and digital devices are now available for use in various nuclear safety-related applications. Many of the tests and evaluations necessary to support plant specific applications have been completed. The amount of data and documentation that each utility must develop on a case by case basis has been significantly reduced. There are also a number of additional benefits resulting from these industry efforts. The challenges and difficulties in qualifying digital equipment for safety-related applications are now more clearly understood. EPRI has published a lessons learned document (EPRI Report 1001452, Generic Qualification of Commercial Grade Digital Devices: Lessons Learned from Initial Pilots, which covers several different qualification areas, including device selection, project planning, vendor surveys and design reviews, and electromagnetic compatibility (EMC) qualification. Application of the experience and lessons learned from the EPRI pilot activities should help reduce the effort and cost required for future qualification work. Most generic qualification activities for commercial equipment have been conducted using the approach of EPRI TR-106439, Guideline on Evaluation and Acceptance

Leo Spacecraft Charging Design Guidelines: A Proposed NASA Standard

Science.gov (United States)

Hillard, G. B.; Ferguson, D. C.

2004-01-01

Over the past decade, Low Earth Orbiting (LEO) spacecraft have gradually required ever-increasing power levels. As a rule, this has been accomplished through the use of high voltage systems. Recent failures and anomalies on such spacecraft have been traced to various design practices and materials choices related to the high voltage solar arrays. NASA Glenn has studied these anomalies including plasma chamber testing on arrays similar to those that experienced difficulties on orbit. Many others in the community have been involved in a comprehensive effort to understand the problems and to develop practices to avoid them. The NASA Space Environments and Effects program, recognizing the timeliness of this effort, commissioned and funded a design guidelines document intended to capture the current state of understanding. This document, which was completed in the spring of 2003, has been submitted as a proposed NASA standard. We present here an overview of this document and discuss the effort to develop it as a NASA standard.

Clean air program : design guidelines for bus transit systems using compressed natural gas as an alternative fuel

Science.gov (United States)

1996-06-01

This report documents design guidelines for the safe use of Compressed Natural Gas (CNG). The report is designed to provide guidance, information on safe industry practices, applicable national codes and standards, and reference data that transit age...

Information and Communication Technology (ICT) Standards and Guidelines. Final rule.

Science.gov (United States)

2017-01-18

We, the Architectural and Transportation Barriers Compliance Board (Access Board or Board), are revising and updating, in a single rulemaking, our standards for electronic and information technology developed, procured, maintained, or used by Federal agencies covered by section 508 of the Rehabilitation Act of 1973, as well as our guidelines for telecommunications equipment and customer premises equipment covered by Section 255 of the Communications Act of 1934. The revisions and updates to the section 508-based standards and section 255-based guidelines are intended to ensure that information and communication technology covered by the respective statutes is accessible to and usable by individuals with disabilities.

Development of manufacturing equipment and QC equipment for DUPIC fuel

International Nuclear Information System (INIS)

Yang, Myung Seung; Park, J.J.; Lee, J.W.; Kim, S.S.; Yim, S.P.; Kim, J.H.; Kim, K.H.; Na, S.H.; Kim, W.K.; Shin, J.M.; Lee, D.Y.; Cho, K.H.; Lee, Y.S.; Sohn, J.S.; Kim, M.J.

1999-05-01

In this study, DUPIC powder and pellet fabrication equipment, welding system, QC equipment, and fission gas treatment are developed to fabricate DUPIC fuel at IMEF M6 hot cell. The systems are improved to be suitable for remote operation and maintenance with the manipulator at hot cell. Powder and pellet fabrication equipment have been recently developed. The systems are under performance test to check remote operation and maintenance. Welding chamber and jigs are designed and developed to remotely weld DUPIC fuel rod with manipulators at hot cell. Remote quality control equipment are being tested for analysis and inspection of DUPIC fuel characteristics at hot cell. And trapping characteristics is analyzed for cesium and ruthenium released under oxidation/reduction and sintering processes. The design criteria and process flow diagram of fission gas treatment system are prepared incorporating the experimental results. The fission gas treatment system has been successfully manufactured. (Author). 33 refs., 14 tabs., 91 figs

Seismic PSA implementation standards by AESJ and the utilization of the advanced safety examination guideline for seismic design for nuclear power plant

International Nuclear Information System (INIS)

Ebisawa, Katsumi; Hibino, Kenta

2008-01-01

The Advanced Safety Examination Guideline for Seismic Design for Nuclear Power Plant (the advanced safety examination guideline) was worked out on September 19, 2006. In this paper, a summary of the method of probability theory in the advanced safety examination guideline and the Seismic PSA Implementation Standards is stated. On utilization of the probability theory for the advanced safety examination guideline, the uncertainty resulting from the process of the decision of the basic design earthquake ground motion (Ss) is stated to be considered using the proper method. The references of the extra probability for evaluation of earthquake hazard and combination of the working load and the earthquake load are stated. Definition, evaluation method and effort to lower the 'residual risks', and relation between the residual risks and the extra probability of Ss are described. A summary of the earthquake-resistant design for nuclear power facilities is explained by the old guideline. (S.Y.)

Applications of EVA guidelines and design criteria. Volume 3: EVA systems cost model formating

Science.gov (United States)

Brown, N. E.

1973-01-01

The development of a model for estimating the impact of manned EVA costs on future payloads is discussed. Basic information on the EV crewman requirements, equipment, physical and operational characteristics, and vehicle interfaces is provided. The cost model is being designed to allow system designers to quantify the impact of EVA on vehicle and payload systems.

Italy-Japan international project-based learning for developing human resources using design of welfare equipment as a subject.

Science.gov (United States)

Hanafusa, A; Komeda, T; Ito, K; Zobel, P Beomonte

2015-08-01

Project-based learning (PBL) is effective for developing human resources of young students. The design of welfare equipment, such as wheelchairs and gait assistive devices, is taken as the subject in this study because these devices must be fit to their environment, users, and method of use; students must consider the circumstances of each country concerned. The program commenced in 2012 at L'Aquila, Italy, and the Shibaura Institute of Technology, Japan and has been continuing for three years. Students were divided into four groups and discussions were held on how to adapt the equipment to the user and environment. After discussion, they designed and simulated a model of the equipment using CAD. Finally, they presented their designs to each other. Through the program, students had fruitful discussions, exchanged ideas from different cultures, and learned from each other. Furthermore, friendships among the students were nurtured. It is believed that the objective of the program was satisfactorily accomplished.

Housing, Equipment, and Design Research and Scholarship: A Family and Consumer Sciences Perspective.

Science.gov (United States)

Beamish, Julia O.; Ahn, Mira; Seiling, Sharon

2001-01-01

Analysis of research on housing, equipment, and design (n=333) in the Journal of Home Economics/Journal of Family and Consumer Sciences (1985-2000), Home Economics Research Journal/Family and Consumer Sciences Research Journal (1985- 2000), and Housing and Society (1985-1999) found that articles declined by more than 50% and behavior theories were…

Integration of Educational Methods and Physical Settings: Design Guidelines for High/Scope Methodology in Pre-Schools

Science.gov (United States)

Izadpanah, Shirin; Günçe, Kaðan

2014-01-01

Quality design and appropriate space organization in preschool settings can support preschool children's educational activities. Although the relationship between the well-being and development of children and physical settings has been emphasized by many early childhood researchers, there is still a need for theoretical design guidelines that are…

Application of the international guidelines for machinery breakdown prevention at nuclear power plants

International Nuclear Information System (INIS)

Wendland, W.G.

2001-01-01

For more than forty years as a specialized branch of the worldwide insurance industry, the nuclear insurance pools have underwritten property damage protection for nuclear facilities throughout the world. At power plants insured by the pools, an enviable record of operational safety has been attained. Nevertheless, electrical and mechanical equipment does break down occasionally. Although these failures do not necessarily compromise nuclear safety, they can cause significant damage to equipment, leading to a considerable loss of generating revenue and causing sizeable insurance losses. Since insurance companies have a large financial stake in nuclear power plants, their goal is to minimize insurance losses, including the failure of systems and equipment and ensuing consequential damages. To ensure that the insurance risk is properly underwritten, insurance companies analyze loss information, develop loss prevention guidelines and focus loss control activities on those areas where insurance risk is most significant. This paper provides a chronology of the development of the ''International Guidelines for Machinery Breakdown Prevention at Nuclear Power Plants'' and describes the results of insurance inspections conducted using these guidelines. Included is a summary of guideline content and of insurance loss experience between 1962 and 1999. (author)

Measure Guideline: Air Conditioner Diagnostics, Maintenance, and Replacement

Energy Technology Data Exchange (ETDEWEB)

Springer, D.; Dakin, B.

2013-03-01

This guideline responds to the need for an efficient means of identifying, diagnosing, and repairing faults in air conditioning systems in existing homes that are undergoing energy upgrades. Inadequate airflow due to constricted ducts or undersized filters, improper refrigerant charge, and other system defects can be corrected at a fraction of the cost of equipment replacement and can yield significant savings. The guideline presents a two-step approach to diagnostics and repair.

Measure Guideline. Air Conditioner Diagnostics, Maintenance, and Replacement

Energy Technology Data Exchange (ETDEWEB)

Springer, David [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States); Dakin, Bill [Alliance for Residential Building Innovation (ARBI), Davis, CA (United States)

2013-03-01

This guideline responds to the need for an efficient means of identifying, diagnosing, and repairing faults in air conditioning systems in existing homes that are undergoing energy upgrades. Inadequate airflow due to constricted ducts or undersized filters, improper refrigerant charge, and other system defects can be corrected at a fraction of the cost of equipment replacement and can yield significant savings. The guideline presents a two-step approach to diagnostics and repair.

Research program for seismic qualification of nuclear plant electrical and mechanical equipment. Task 4. Use of fragility in seismic design of nuclear plant equipment. Volume 4

International Nuclear Information System (INIS)

Kana, D.D.; Pomerening, D.J.

1984-08-01

The Research Program for Seismic Qualification of Nuclear Plant Electrical and Mechanical Equipment has spanned a period of three years and resulted in seven technical summary reports, each of which have covered in detail the findings of different tasks and subtasks, and have been combined into five NUREG/CR volumes. Volume 4 presents study of the use of fragility concepts in the design of nuclear plant equipment and compares the results of state-of-the-art proof testing with fragility testing

A systematic approach applied in design of a micro heat exchanger

DEFF Research Database (Denmark)

Omidvarnia, Farzaneh; Hansen, Hans Nørgaard; Sarhadi, Ali

2016-01-01

The number of products benefiting from micro components in the market is increasing, and consequently, the demand for well-matched tools, equipment and systems with micro features is eventually increasing as well. During the design process of micro products, a number of issues appear which...... from the design process of the micro heat exchanger are added to the RTC unit and can be applied as guidelines in design pro- cess of any other micro heat exchanger. In other words, the current study can provide a useful guideline in design for manufacturing of micro products....... are inherent due to the down scaling or physical phenomena dominating in the micro range but negligible in the macro scale. In fact, some aspects in design for micro manufacturing are considerably different compared to the de- sign procedure taken at the macro level. Identifying the differences between design...

COMP report: CPQR technical quality control guidelines for low-dose-rate permanent seed brachytherapy.

Science.gov (United States)

Beaulieu, Luc; Radford, Dee-Ann; Eduardo Villarreal-Barajas, J

2018-03-14

The Canadian Organization of Medical Physicists (COMP), in close partnership with the Canadian Partnership for Quality Radiotherapy (CPQR) has developed a series of Technical Quality Control (TQC) guidelines for radiation treatment equipment. These guidelines outline the performance objectives that equipment should meet in order to ensure an acceptable level of radiation treatment quality. The TQC guidelines have been rigorously reviewed and field tested in a variety of Canadian radiation treatment facilities. The development process enables rapid review and update to keep the guidelines current with changes in technology. This article contains detailed performance objectives and safety criteria for low-dose-rate (LDR) permanent seed brachytherapy. © 2018 The Authors. Journal of Applied Clinical Medical Physics published by Wiley Periodicals, Inc. on behalf of American Association of Physicists in Medicine.

Specific features of organizng the computer-aided design of radio-electronic equipment for electrophysical facilities

International Nuclear Information System (INIS)

Mozin, I.V.; Vasil'ev, M.P.

1985-01-01

Problems of developing systems for computer-aided design (CAD) of radioelectronic equipment for large electrophysical facilities such as charged particle accelerators of new generation are discussed. The PLATA subsystem representing a part of CAD and used for printed circuit design is described. The subsystem PLATA is utilized to design, on the average, up to 150 types of circuits a year, 100-120 of which belong to circuits of increased complexity. In this case labour productivity of a designer at documentation increases almost two times

Design and construction of a air pollutant gases sampler equipment

International Nuclear Information System (INIS)

Gomez S, R.A.; Rodriguez, T.J.

1996-01-01

This thesis is about the sketch and construction of an equipment which samples contaminated gases in the air. The topic of this work, is to propose a solution for imported and national equipment. The solution consist on lower prices of imported and national equipment without loosing the accuracy and the precision of those now available. The investigation shows all process to sample gases and theirs measurement for which all the mechanical, electric and electronic equipment, and the necessary software for giving the results in a computerized way were outlined. With this work it was able to succeed in measurements with a national low price, accurate, reliable, programmable, completely automatic and easy to use. This equipment exceed in accuracy the Japanese and the american equipment

Strategy Guideline: Compact Air Distribution Systems

Energy Technology Data Exchange (ETDEWEB)

Burdick, A.

2013-06-01

This Strategy Guideline discusses the benefits and challenges of using a compact air distribution system to handle the reduced loads and reduced air volume needed to condition the space within an energy efficient home. Traditional systems sized by 'rule of thumb' (i.e., 1 ton of cooling per 400 ft2 of floor space) that 'wash' the exterior walls with conditioned air from floor registers cannot provide appropriate air mixing and moisture removal in low-load homes. A compact air distribution system locates the HVAC equipment centrally with shorter ducts run to interior walls, and ceiling supply outlets throw the air toward the exterior walls along the ceiling plane; alternatively, high sidewall supply outlets throw the air toward the exterior walls. Potential drawbacks include resistance from installing contractors or code officials who are unfamiliar with compact air distribution systems, as well as a lack of availability of low-cost high sidewall or ceiling supply outlets to meet the low air volumes with good throw characteristics. The decision criteria for a compact air distribution system must be determined early in the whole-house design process, considering both supply and return air design. However, careful installation of a compact air distribution system can result in lower material costs from smaller equipment, shorter duct runs, and fewer outlets; increased installation efficiencies, including ease of fitting the system into conditioned space; lower loads on a better balanced HVAC system, and overall improved energy efficiency of the home.

Maintenance Trades Guidelines

Science.gov (United States)

Weidner, Theodore J.

2008-01-01

In 2002, APPA published "Maintenance Staffing Guidelines for Educational Facilities," the first building maintenance trades staffing guideline designed to assist educational facilities professionals with their staffing needs. addresses how facilities professionals can determine the appropriate size and mix of their organization. Contents…

Radio frequency sputtering equipment: design considerations for the disc and annulus system

International Nuclear Information System (INIS)

Usher, D.M.; Cox, G.A.

1981-01-01

The basic equations important in the design of rf sputtering equipment are presented. Attention is restricted to the 'disc and annulus' system and simple techniques in lead-through fabrication and electrode shielding are described. Also rf power oscillator theory is used to derive the important parameters of power generation. Load coupling and power matching techniques are discussed. Problems of the magnetic field coil design are analysed and a value for the thermal conductivity of coils wound from polyurethane coated wire is given, namely k = 0.64 W m -1 / 0 C -1 , permitting the steady state temperature distribution inside such coils to be predicted. (author)

Conceptual design report, CEBAF basic experimental equipment

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-04-13

The Continuous Electron Beam Accelerator Facility (CEBAF) will be dedicated to basic research in Nuclear Physics using electrons and photons as projectiles. The accelerator configuration allows three nearly continuous beams to be delivered simultaneously in three experimental halls, which will be equipped with complementary sets of instruments: Hall A--two high resolution magnetic spectrometers; Hall B--a large acceptance magnetic spectrometer; Hall C--a high-momentum, moderate resolution, magnetic spectrometer and a variety of more dedicated instruments. This report contains a short description of the initial complement of experimental equipment to be installed in each of the three halls.

Guidelines for the development of natural phenomena hazards design criteria for surface facilities

International Nuclear Information System (INIS)

Nelson, T.A.; Hossain, Q.A.; Murray, R.C.

1992-01-01

This paper discusses the rationale behind the guidelines, criteria, and methodologies that are currently used for natural phenomena hazard design and evaluation of DOE nuclear and non-nuclear facilities. The bases for the performance goals and usage categories specified in UCRL-15910 are examined, and the sources of intentional conservatism in the analyses, design, and evaluation methods and criteria are identified. Outlines of recent developments/changes in DOE Orders related to Natural Phenomena hazard mitigation are also presented. Finally, the authors recommend the use of DOE methodologies as embodied in UCRL-15910 for design and evaluation of surface facilities of the high level nuclear waste repository site

Keeping Kids Safe from a Design Perspective: Ethical and Legal Guidelines for Designing a Video-Based App for Children

Science.gov (United States)

Zydney, Janet Mannheimer; Hooper, Simon

2015-01-01

Educators can use video to gain invaluable information about their students. A concern is that collecting videos online can create an increased security risk for children. The purpose of this article is to provide ethical and legal guidelines for designing video-based apps for mobile devices and the web. By reviewing the literature, law, and code…

Equipment Design and Cost Estimation for Small Modular Biomass Systems, Synthesis Gas Cleanup, and Oxygen Separation Equipment; Task 9: Mixed Alcohols From Syngas -- State of Technology

Energy Technology Data Exchange (ETDEWEB)

Nexant Inc.

2006-05-01

This deliverable is for Task 9, Mixed Alcohols from Syngas: State of Technology, as part of National Renewable Energy Laboratory (NREL) Award ACO-5-44027, ''Equipment Design and Cost Estimation for Small Modular Biomass Systems, Synthesis Gas Cleanup and Oxygen Separation Equipment''. Task 9 supplements the work previously done by NREL in the mixed alcohols section of the 2003 technical report Preliminary Screening--Technical and Economic Assessment of Synthesis Gas to Fuels and Chemicals with Emphasis on the Potential for Biomass-Derived Syngas.

The CARE guidelines: consensus-based clinical case report guideline development.

Science.gov (United States)

Gagnier, Joel J; Kienle, Gunver; Altman, Douglas G; Moher, David; Sox, Harold; Riley, David

2014-01-01

A case report is a narrative that describes, for medical, scientific, or educational purposes, a medical problem experienced by one or more patients. Case reports written without guidance from reporting standards are insufficiently rigorous to guide clinical practice or to inform clinical study design. Develop, disseminate, and implement systematic reporting guidelines for case reports. We used a three-phase consensus process consisting of (1) pre-meeting literature review and interviews to generate items for the reporting guidelines, (2) a face-to-face consensus meeting to draft the reporting guidelines, and (3) post-meeting feedback, review, and pilot testing, followed by finalization of the case report guidelines. This consensus process involved 27 participants and resulted in a 13-item checklist-a reporting guideline for case reports. The primary items of the checklist are title, key words, abstract, introduction, patient information, clinical findings, timeline, diagnostic assessment, therapeutic interventions, follow-up and outcomes, discussion, patient perspective, and informed consent. We believe the implementation of the CARE (CAse REport) guidelines by medical journals will improve the completeness and transparency of published case reports and that the systematic aggregation of information from case reports will inform clinical study design, provide early signals of effectiveness and harms, and improve healthcare delivery. Copyright © 2014 Reproduced with permission of Global Advances in Health and Medicine. Published by Elsevier Inc. All rights reserved.