Fuel Economy Improvement of a Heavy-Duty Powertrain by Using Hardware-in-Loop Simulation and Calibration

Directory of Open Access Journals (Sweden)

Bolan Liu

2015-09-01

Full Text Available Fuel economy efficiency is one of the most important parameters for vehicle powertrains, which is of particular interest for heavy-duty powertrain calibration. Conventionally, this work relies heavily on road tests, which cost more and may lead to long duration product development cycles. The paper proposes a novel hardware-in-loop modeling and calibration method to work it out. A dSPACE hardware-based test bench was successfully established and validated, which is valuable for a more efficient and easier shift schedule in calibration. Meanwhile, a real-time dynamic powertrain model, including a diesel engine, torque converter, gear box and driver model was built. Typical driving cycles that both velocity and slope information were constructed for different road conditions. A basic economic shift schedule was initially calculated and then optimal calibrated by the test bench. The results show that there is an optimal relationship between an economic shift schedule and speed regulation. By matching the best economic shift schedule regulation to different road conditions; the fuel economy of vehicles can be improved. In a smooth driving cycle; when the powertrain applies a larger speed regulation such as 12% and the corresponding shift schedule; the fuel consumption is smaller and is reduced by 13%. In a complex driving cycle, when the powertrain applies a smaller speed regulation such as 5% along with the corresponding shift schedule; the fuel consumption is smaller and is reduced by 5%. The method thus can provide guidance for economic calibration experiments of off-road heavy-duty vehicles.

The new generation of the medium four cylinder - spark ignition engines by FIAT-GM powertrain; Die neue Generation der mittleren Vierzylinder - Ottomotoren von FIAT-GM Powertrain

Energy Technology Data Exchange (ETDEWEB)

Grebe, U.D.; Gebhard, P.; Loehnert, T.; Opacak, I.; Theis, H.G. [Opel Powertrain GmbH, ein Unternehmen von FIAT-GM Powertrain (Germany)

2003-07-01

The medium size gasoline engine family by FIAT-GM Powertrain, internally called Family 1, was redesigned with regard to fuel consumption, quality, maintenance and manufacturing cost. Next to the optimizations the refinement focused on modular use of components. The 1.6 l engine has the biggest production share and is the first variant of the new third generation of this engine family. The engine is using tappets with mechanical lash adjustment and a thermomanagement system. Next to the power output of 76 kW and the maximum torque of 147 Nm the development included the integration of a combustion system with port deactivation and high amounts of recirculated exhaust gas. This reduced the fuel consumption significantly. The new engine will be used in the Opel Astra first. The fuel consumption in the European MVEG test cycle is reduced by 7% from 7.0 to 6.5 l/100 km. This positions the vehicle in the upper segment. Alternative solutions use much more complex measures such as stratified charge gasoline direct injection to achieve comparable fuel consumptions. The described cost efficient system combines best customer benefit in terms of fuel consumption and vehicle performance with optimized manufacturing cost and excellent long-term reliability. This engine concept using modular components creates a platform for the medium four-cylinder gasoline engine family. This platform will be the basis for the entire redesigned engine family applying different combinations of the modules. (orig.) [German] Die mittlere Ottomotoren-Baureihe von FIAT-GM Powertrain mit der Bezeichnung Familie 1 wurde grundlegend hinsichtlich Kraftstoffverbrauch, Emissionsreduzierung, Qualitaet, Wartungsaufwand und Herstellkosten ueberarbeitet. Neben den Optimierungen stand die Modularisierung der Komponenten im Mittelpunkt. Der 1,6 Liter Motor stellt das groesste Produktionsvolumen und ist die erste Variante der weiterentwickelten, dritten Generation dieser Motorfamilie. Der Motor verwendet einen

Optimal control of a repowered vehicle: Plug-in fuel cell against plug-in hybrid electric powertrain

Energy Technology Data Exchange (ETDEWEB)

Tribioli, L., E-mail: laura.tribioli@unicusano.it; Cozzolino, R. [Dept. of Industrial Engineering, University of Rome Niccolo’ Cusano (Italy); Barbieri, M. [Engineering Dept., University of Naples Parthenope, Centro Direzionale-Isola C4, 80143 Naples (Italy)

2015-03-10

This paper describes two different powertrain configurations for the repowering of a conventional vehicle, equipped with an internal combustion engine (ICE). A model of a mid-sized ICE-vehicle is realized and then modified to model both a parallel plug-in hybrid electric powertrain and a proton electrolyte membrane (PEM) fuel cell (FC) hybrid powertrain. The vehicle behavior under the application of an optimal control algorithm for the energy management is analyzed for the different scenarios and results are compared.

Optimal control of a repowered vehicle: Plug-in fuel cell against plug-in hybrid electric powertrain

International Nuclear Information System (INIS)

Tribioli, L.; Cozzolino, R.; Barbieri, M.

2015-01-01

This paper describes two different powertrain configurations for the repowering of a conventional vehicle, equipped with an internal combustion engine (ICE). A model of a mid-sized ICE-vehicle is realized and then modified to model both a parallel plug-in hybrid electric powertrain and a proton electrolyte membrane (PEM) fuel cell (FC) hybrid powertrain. The vehicle behavior under the application of an optimal control algorithm for the energy management is analyzed for the different scenarios and results are compared

Method of converting an existing vehicle powertrain to a hybrid powertrain system

Science.gov (United States)

Reed, Jr., Richard G.; Boberg, Evan S.; Lawrie, Robert E.; Castaing, Francois J.

2001-12-25

A method of converting an existing vehicle powertrain including a manual transmission to a hybrid powertrain system with an automated powertrain transmission. The first step in the method of attaching a gear train housing to a housing of said manual transmission, said gear train housing receiving as end of drive shaft of said transmission and rotatably supporting a gear train assembly. Secondly, mounting an electric motor/generator to said gear train housing and attaching a motor/generator drive shaft of said electric motor/generator to said gear train assembly. Lastly, connecting an electro-mechanical clutch actuator to a friction clutch mechanism of said manual transmission.

Energy integration on multi-periods and multi-usages for hybrid electric and thermal powertrains

International Nuclear Information System (INIS)

Dimitrova, Zlatina; Maréchal, François

2015-01-01

The improvement of the efficiency of vehicle energy systems promotes an active search to find innovative solutions during the design process. This requires more accurate modeling of complex systems, which offers new ways to improve the design efficiency of energy systems. The vehicle is a highly dynamic system. The size and the efficiency of the convertors are dependent on the dynamic driving profile. In order to increase the energy efficiency, using energy integration techniques, an adapted methodology is required to choose the best points for the integrated system design. The idea is to clusterize the dynamic profile on typical multi-periods of the vehicle use. The energy system design is then optimized for these typical multi-periods. In this article a new methodology is applied on hybrid electric vehicles, in order to define the energy integrated powertrain configuration of the vehicle. The energy recovery potential of a single stage Organic Rankine Cycle for a thermal engine in combination with a hybrid electric powertrain is assessed for different drive cycles profiles and comfort situations. After the energy integration, a multi-objective optimization is applied to define the optimal design of a hybrid electric vehicle with a waste heat recovery system. - Highlights: • K-means algorithm transforms the dynamic driving profile on static multi-periods. • The clusters represent the typical powertrain use and size the heat recovery utility. • The maximal heat recovery potential on thermal powertrains is 11% for urban driving. • The maximal heat recovery potential on hybrid electric powertrains is 5%. • Engine downsizing increases heat recovery potential on hybrid electric powertrains

Model-based testing in powertrain development; Modellgestuetzte Erprobungsmethodik in der Antriebsstrangentwicklung

Energy Technology Data Exchange (ETDEWEB)

Albers, A.; Schyr, C. [Inst. fuer Produktentwicklung der Univ. Karlsruhe (T.H.) (Germany)

2005-07-01

The paper describes a new methodical approach for a model-based testing of powertrain components in vehicle development. The presented methodology is based on a holistic model environment which covers the major dynamic effects of the vehicle in an early development phase and refines the models during the testing phase on the different test bed configurations. This allows a realistic loading of the mechanical components and their electronic control units in parallel to a simulation based analysis of design and application variants in the mechanics and software and their influence onto the complete vehicle. In the first application example the development of a pre-adjustable transmission for passenger cars is presented. In the second example the testing concept for tracked vehicles with hydrostatic drivetrain is described. (orig.)

Transition strategy of the transportation energy and powertrain in China

International Nuclear Information System (INIS)

Wang Hewu; Ouyang Minggao

2007-01-01

The problems of the transportation energy and environment are the major challenges faced globally in the 21st century and are especially serious for China. The future 20 years is the strategic opportunity period of the transition of the transportation energy and powertrain system for China. The greatest characteristics of hydrogen economy lie in its diversity of the primary energy source, the unification of energy carrier and the greening of energy transformation. Development of hydrogen energy transportation powertrain system is suitable for China from the views of the situation of Chinese resources and energy sources, the urban and rural layouts, the superiority of later development and the successful practices of clean cars and electric vehicle development projects. The transition of the transportation energy powertrain system includes three parts: the transition of the energy structure, the transition of the powertrain system and the transition of the fuel infrastructure. The technical pathways of energy powertrain system transition includes expending the use of gaseous fuel to prompt the multiform of the transportation energy and to prepare for the transition of the infrastructure simultaneously, developing and promoting the hybrid technology to solve the current energy and environment problems and to prepare for the transition of powertrain system, and focusing on the research and development and demonstration of fuel cell vehicles and the hydrogen energy technology to prompt the earlier formation of the market of fuel cell vehicles. The goal in the near and medium term of transition is to reduce the fuel consumption by 100 million ton in 2020 by substituting and saving, and the long-term goal is to setup the infrastructure of hydrogen and fuel cell vehicle as the main one replacing the petroleum internal combustion engine vehicle. In order to realize the strategic goals of the transition, the four-phases strategic periods and research and development

Method and apparatus for controlling a powertrain system including a multi-mode transmission

Science.gov (United States)

Hessell, Steven M.; Morris, Robert L.; McGrogan, Sean W.; Heap, Anthony H.; Mendoza, Gil J.

2015-09-08

A powertrain including an engine and torque machines is configured to transfer torque through a multi-mode transmission to an output member. A method for controlling the powertrain includes employing a closed-loop speed control system to control torque commands for the torque machines in response to a desired input speed. Upon approaching a power limit of a power storage device transferring power to the torque machines, power limited torque commands are determined for the torque machines in response to the power limit and the closed-loop speed control system is employed to determine an engine torque command in response to the desired input speed and the power limited torque commands for the torque machines.

Review of the Fuel Saving, Life Cycle GHG Emission, and Ownership Cost Impacts of Lightweighting Vehicles with Different Powertrains.

Science.gov (United States)

Luk, Jason M; Kim, Hyung Chul; De Kleine, Robert; Wallington, Timothy J; MacLean, Heather L

2017-08-01

The literature analyzing the fuel saving, life cycle greenhouse gas (GHG) emission, and ownership cost impacts of lightweighting vehicles with different powertrains is reviewed. Vehicles with lower powertrain efficiencies have higher fuel consumption. Thus, fuel savings from lightweighting internal combustion engine vehicles can be higher than those of hybrid electric and battery electric vehicles. However, the impact of fuel savings on life cycle costs and GHG emissions depends on fuel prices, fuel carbon intensities and fuel storage requirements. Battery electric vehicle fuel savings enable reduction of battery size without sacrificing driving range. This reduces the battery production cost and mass, the latter results in further fuel savings. The carbon intensity of electricity varies widely and is a major source of uncertainty when evaluating the benefits of fuel savings. Hybrid electric vehicles use gasoline more efficiently than internal combustion engine vehicles and do not require large plug-in batteries. Therefore, the benefits of lightweighting depend on the vehicle powertrain. We discuss the value proposition of the use of lightweight materials and alternative powertrains. Future assessments of the benefits of vehicle lightweighting should capture the unique characteristics of emerging vehicle powertrains.

Design Optimization of a Hybrid Electric Vehicle Powertrain

Science.gov (United States)

Mangun, Firdause; Idres, Moumen; Abdullah, Kassim

2017-03-01

This paper presents an optimization work on hybrid electric vehicle (HEV) powertrain using Genetic Algorithm (GA) method. It focused on optimization of the parameters of powertrain components including supercapacitors to obtain maximum fuel economy. Vehicle modelling is based on Quasi-Static-Simulation (QSS) backward-facing approach. A combined city (FTP-75)-highway (HWFET) drive cycle is utilized for the design process. Seeking global optimum solution, GA was executed with different initial settings to obtain sets of optimal parameters. Starting from a benchmark HEV, optimization results in a smaller engine (2 l instead of 3 l) and a larger battery (15.66 kWh instead of 2.01 kWh). This leads to a reduction of 38.3% in fuel consumption and 30.5% in equivalent fuel consumption. Optimized parameters are also compared with actual values for HEV in the market.

ISG hybrid powertrain: a rule-based driver model incorporating look-ahead information

Science.gov (United States)

Shen, Shuiwen; Zhang, Junzhi; Chen, Xiaojiang; Zhong, Qing-Chang; Thornton, Roger

2010-03-01

According to European regulations, if the amount of regenerative braking is determined by the travel of the brake pedal, more stringent standards must be applied, otherwise it may adversely affect the existing vehicle safety system. The use of engine or vehicle speed to derive regenerative braking is one way to avoid strict design standards, but this introduces discontinuity in powertrain torque when the driver releases the acceleration pedal or applies the brake pedal. This is shown to cause oscillations in the pedal input and powertrain torque when a conventional driver model is adopted. Look-ahead information, together with other predicted vehicle states, are adopted to control the vehicle speed, in particular, during deceleration, and to improve the driver model so that oscillations can be avoided. The improved driver model makes analysis and validation of the control strategy for an integrated starter generator (ISG) hybrid powertrain possible.

A study on compression braking as a means for brake energy recovery for pneumatic hybrid powertrains

OpenAIRE

Trajkovic, Sasa; Tunestål, Per; Johansson, Bengt

2013-01-01

Hybrid powertrains have become a very attractive technology over the last ten years due to their potential for lowering fuel consumption and emissions. A large portion of all manufacturers worldwide are now focusing on hybrid electric powertrains, which are the most common hybrid powertrains of today. However, in recent years a new technology has emerged, namely the pneumatic hybrid powertrain. Although the concept is still only under research, it has been tested in various laboratories with ...

How to simultaneously achieve low emissions and high efficiency in a hybrid powertrain

NARCIS (Netherlands)

Mourad, S.; Eijnden, E. van den; Foster, D.L.; Helden, M. van; Rondel, M.; Schmal, P.

2001-01-01

In order to investigate the possibilities of hybrid driveline architecture and to provide a platform for further technical developments, TNO has designed and prototyped a test platform for a series hybrid powertrain, including a compact, highly advanced generator set. This powertrain is subjected to

Optimal Design of a Novel Hybrid Electric Powertrain for Tracked Vehicles

Directory of Open Access Journals (Sweden)

Zhaobo Qin

2017-12-01

Full Text Available Tracked vehicles have been widely used in construction, agriculture, and the military. Major problems facing the industry, however, are high emissions and fuel consumption. Hybrid electric tracked vehicles have thus become increasingly popular because of their improved fuel economy and reduced emissions. While the series hybrid system has drawn the most attention and has been applied in most cases, the low efficiency caused by energy conversion losses and large propulsion motors has limited its development. A novel multi-mode powertrain with two output shafts controlling each side of the track independently is first proposed. The powertrain is a three-planetary-gear power-split system with one engine, three motors, and an ultracapacitor pack. Compared with the existing technologies, the proposed powertrain can realize skid steering without an extra steering mechanism, and significantly improve the overall efficiency. To demonstrate the advantages of the novel powertrain, a topology-control-size integrated optimization problem is solved based on drivability, fuel economy, and cost. Final simulation results show that the optimized design with downsized components can produce about a 30% improvement in drivability and a 15% improvement in fuel economy compared with the commonly used series hybrid benchmark. Moreover, the optimized design is verified to be much more economical taking cumulative cost into account, which is very attractive for potential industrial applications in the future.

Application of the X-in-the-Loop Testing Method in the FCV Hybrid Degree Test

Directory of Open Access Journals (Sweden)

Haiyu Gao

2018-02-01

Full Text Available With the development of fuel cell vehicle technology, an effective testing method that can be applied to develop and verify the fuel cell vehicle powertrain system is urgently required. This paper presents the X-in-the-Loop (XiL testing method in the fuel cell vehicle (FCV hybrid degree test to resolve the first and key issues for the powertrain system design, and the test process and scenarios were designed. The hybrid degree is redefined into the static hybrid degree for system architecture design and the dynamic hybrid degree for vehicle control strategy design, and an integrated testing platform was introduced and a testing application was implemented by following the designed testing flowchart with two loops. Experimental validations show that the sizing of the FCE (Fuel Cell Engine, battery pack, and traction motor with the powertrain architecture can be determined, the control strategy can be evaluated seamlessly, and a systematic powertrain testing solution can be achieved through the whole development process. This research has developed a new testing platform and proposed a novel testing method on the fuel cell vehicle powertrain system, which will be a contribution to fuel cell vehicle technology and its industrialization.

Propulsion Powertrain Real-Time Simulation Using Hardware-in-the-Loop (HIL) for Aircraft Electric Propulsion System

Science.gov (United States)

Choi, Benjamin B.; Brown, Gerald V.

2017-01-01

It is essential to design a propulsion powertrain real-time simulator using the hardware-in-the-loop (HIL) system that emulates an electrified aircraft propulsion (EAP) systems power grid. This simulator would enable us to facilitate in-depth understanding of the system principles, to validate system model analysis and performance prediction, and to demonstrate the proof-of-concept of the EAP electrical system. This paper describes how subscale electrical machines with their controllers can mimic the power components in an EAP powertrain. In particular, three powertrain emulations are presented to mimic 1) a gas turbo-=shaft engine driving a generator, consisting of two permanent magnet (PM) motors with brushless motor drives, coupled by a shaft, 2) a motor driving a propulsive fan, and 3) a turbo-shaft engine driven fan (turbofan engine) operation. As a first step towards the demonstration, experimental dynamic characterization of the two motor drive systems, coupled by a mechanical shaft, were performed. The previously developed analytical motor models1 were then replaced with the experimental motor models to perform the real-time demonstration in the predefined flight path profiles. This technique can convert the plain motor system into a unique EAP power grid emulator that enables rapid analysis and real-time simulation performance using hardware-in-the-loop (HIL).

The new electric powertrain on the 2013 MY Nissan LEAF

Energy Technology Data Exchange (ETDEWEB)

Nakada, Naoki; Nakazawa, Shinsuke [Nissan Motor Co., Ltd. (Japan)

2013-08-01

The Nissan LEAF was launched in 2010 as the world's first mass-produced electric vehicle. Among its many honours received to date, the Nissan LEAF won the 2011 European Car of the Year (COTY) award, the 2011 World COTY award, the 2011-2012 Japan COTY award and was named in Ward's 10 Best Engines list for 2011, which attest to its high market acclaim. As of 2012, over 46,000 units of the Nissan LEAF are now on the road in some 33 countries worldwide, especially in Japan, the U.S. and Europe. The 2013 model year Nissan LEAF has been announced and released, featuring substantial improvements in all-around performance based on a thoroughgoing analysis of the driving data recorded by the Nissan LEAF in real-world use during the past two years. One of the major changes made to the 2013 model is the adoption of an all-new electric powertrain. The traction motor, inverter and charging unit of this new electric powertrain have all been fully redesigned. Moreover, these high-voltage parts specific to an EV are now assembled into an integrated powertrain that is 30% smaller, 10% lighter and significantly less expensive than the corresponding electric powertrain used on the 2011 model. The driving range of the 2013 Nissan LEAF has also been extended by more than 10% over that of the 2011 model as a result of adopting an improved cooperative regenerative braking system and a heat pump-based air-conditioning system, lightening the vehicle weight, lowering the drag coefficient, and reducing the parasitic loads of the auxiliary units. In addition, the human-machine interface elements, including the navigation system and the instruments have also been improved to enhance the convenience of driving an EV. This paper describes various key technologies featured on the 2013 Nissan LEAF, focusing in particular on the newly developed electric powertrain. (orig.)

Characterization of the powertrain components for a hybrid quadricycle

Science.gov (United States)

De Santis, M.; Agnelli, S.; Silvestri, L.; Di Ilio, G.; Giannini, O.

2016-06-01

This paper presents the experimental characterization of a prototyping hybrid electric quadricycle, which is equipped with two independently actuated hub (in-wheel) motors and powered by a 51 V 132 Ah LiFeYPO4 battery pack. Such a vehicle employs two hub motors located in the rear axles in order to independently drive/brake the rear wheels; such architecture allows to implement a torque vectoring system to improve the vehicle dynamics. Due to its actuation flexibility, energy efficiency and performance potentials, this architecture is one of the promising powertrain design for electric quadricycle. Experimental data obtained from measurements on the vehicle powertrain components going from the battery pack to the inverter and to the in-wheel motor were employed to generate the hub motor torque response and power efficiency maps in both driving and regenerative braking modes. Furthermore, the vehicle is equipped with a gasoline internal combustion engine as range extender whose efficiency was also characterized.

Real Time Energy Management Control Strategies for Hybrid Powertrains

Science.gov (United States)

Zaher, Mohamed Hegazi Mohamed

In order to improve fuel efficiency and reduce emissions of mobile vehicles, various hybrid power-train concepts have been developed over the years. This thesis focuses on embedded control of hybrid powertrain concepts for mobile vehicle applications. Optimal robust control approach is used to develop a real time energy management strategy for continuous operations. The main idea is to store the normally wasted mechanical regenerative energy in energy storage devices for later usage. The regenerative energy recovery opportunity exists in any condition where the speed of motion is in opposite direction to the applied force or torque. This is the case when the vehicle is braking, decelerating, or the motion is driven by gravitational force, or load driven. There are three main concepts for regernerative energy storing devices in hybrid vehicles: electric, hydraulic, and flywheel. The real time control challenge is to balance the system power demand from the engine and the hybrid storage device, without depleting the energy storage device or stalling the engine in any work cycle, while making optimal use of the energy saving opportunities in a given operational, often repetitive cycle. In the worst case scenario, only engine is used and hybrid system completely disabled. A rule based control is developed and tuned for different work cycles and linked to a gain scheduling algorithm. A gain scheduling algorithm identifies the cycle being performed by the machine and its position via GPS, and maps them to the gains.

Control system for a hybrid powertrain system

Science.gov (United States)

Naqvi, Ali K.; Demirovic, Besim; Gupta, Pinaki; Kaminsky, Lawrence A.

2014-09-09

A vehicle includes a powertrain with an engine, first and second torque machines, and a hybrid transmission. A method for operating the vehicle includes operating the engine in an unfueled state, releasing an off-going clutch which when engaged effects operation of the hybrid transmission in a first continuously variable mode, and applying a friction braking torque to a wheel of the vehicle to compensate for an increase in an output torque of the hybrid transmission resulting from releasing the off-going clutch. Subsequent to releasing the off-going clutch, an oncoming clutch which when engaged effects operation of the hybrid transmission in a second continuously variable mode is synchronized. Subsequent to synchronization of the oncoming clutch, the oncoming clutch is engaged.

Models everywhere. How a fully integrated model-based test environment can enable progress in the future

Energy Technology Data Exchange (ETDEWEB)

Ben Gaid, Mongi; Lebas, Romain; Fremovici, Morgan; Font, Gregory; Le Solliec, Gunael [IFP Energies nouvelles, Rueil-Malmaison (France); Albrecht, Antoine [D2T Powertrain Engineering, Rueil-Malmaison (France)

2011-07-01

The aim of this paper is to demonstrate how advanced modelling approaches coupled with powerful tools allow to set up a complete and coherent test environment suite. Based on a real study focused on the development of a Euro 6 hybrid powertrain with a Euro 5 turbocharged diesel engine, the authors present how a diesel engine simulator including an in-cylinder phenomenological approach to predict the raw emissions can be coupled with a DOC and DPF after-treatment system and embedded in the complete hybrid powertrain to be used in various test environments: - coupled with the control software in a multi-model multi-core simulation platform with test automation features, allowing the simulation speed to be faster than the real-time; - exported in a real time hardware in the loop platform with the ECU and hardware actuators; embedded at the experimental engine test bed to perform driving cycles such as NEDC or FTP cycles with the hybrid powertrain management. Thanks to these complete and versatile test platform suite xMOD/Morphee, all the key issues of a full hybrid powertrain can be addressed efficiently and at low cost compared to the experimental powertrain prototypes: consumption minimisation, energy optimisation, thermal exhaust management. NOx/soots trade off, NO/NO2 ratios.. Having a good balance between versatility and compliancy of the model oriented test platforms such as presented in this paper is the best way to take the maximum benefit of the model developed at each stage of the powertrain development. (orig.)

Paradigm change in automotive powertrain engineering. A techno-economic analysis taking into account environment-political instruments; Paradigmawandel automobiler Antriebstechnologien. Eine techno-oekonomische Analyse unter Beruecksichtigung umweltpolitischer Instrumente

Energy Technology Data Exchange (ETDEWEB)

Stangner, Peter

2011-07-01

The automobile industry is faced with the challenge to introduce concepts for sustainable mobility in terms of low pollutant and CO2 emissions. The author discusses the preconditions and procedures of technological change in the powertrain markets. The effects of techno-economic trends and environment-political instruments are discussed in an international context and illustrated by the example of the market success of diesel engines in Europe. Using innovation-economic theories, he draws conclusions as to the future electrification of powertrains resp. the introduction of electromobility. Not least because of its highly topical content with regard to economic and environmental policy, this publication has high relevance for decision makers in science, industry and politics. By outlining options and chances of future developments, it will help to reduce present concerns about the future. (orig.)

Active-charging based powertrain control in series hybrid electric vehicles for efficiency improvement and battery lifetime extension

Science.gov (United States)

Zhang, Xi; Mi, Chris Chunting; Yin, Chengliang

2014-01-01

This paper presents a powertrain control strategy for a series hybrid electric vehicle (SHEV) based on the integrated design of an active charging scenario and fixed-boundary-layer sliding mode controllers (FBLSMCs). An optimized charging curve for the battery is predetermined rather than subject to engine output and vehicle power demand, which is a total inverse of normal SHEV powertrain control process. This is aimed to remove surge and high-frequency charge current, keep the battery staying in a high state-of-charge (SOC) region and avoid persistently-high charge power, which are positive factors to battery lifetime extension. Then two robust chattering-free FBLSMCs are designed to locate the engine operation in the optimal efficiency area. One is in charge of engine speed control, and the other is for engine/generator torque control. Consequently, not only fuel economy is improved but also battery life expectancy could be extended. Finally, simulation and experimental results confirm the validity and application feasibility of the proposed strategy.

Powertrain diversity and electrification. Challenges and chances for the automotive industry; Antriebsstrangvielfalt und Elektrifizierung. Herausforderungen und Chancen fuer die Automobilindustrie

Energy Technology Data Exchange (ETDEWEB)

Bohr, Bernd [Robert Bosch GmbH, Stuttgart (Germany). Unternehmensbereich Kraftfahrzeugtechnik

2010-07-01

The major challenges and opportunities for the further development of the powertrain can be summed up as follows: - Both the diesel and the gasoline engine offer great potential for reducing consumption and emissions. However, realizing this potential will require heavy investments. - In the long run, the objective is a purely electric powertrain. The route to this objective will be a dual one, with hybrids as an interim technology on the one hand and the further development of the internal-combustion engine on the other. In the short-to-medium term, this will mean a diverse array of powertrain technologies. - The need to invest in both the internal-combustion engine and the electric powertrain, as well as to master the various drive train concepts, presents great challenges for the automotive industry. - The standardization of non-distinctive functions, major components, and interfaces is a lever for reducing costs, especially for the electric powertrain, whose development is only just getting underway. - Innovation partnerships, alliances, and pre-competitive collaboration agreements are a further way of reducing the investment costs of the individual market players, of increasing the speed of development, and thus of increasing the industry's competitiveness. - For three main reasons, the competencies and know-how required for electric vehicles differ from those needed for vehicles with internal-combustion engines. First, there is a far higher share of electrics and electronics in total value-added; second, there is a need for reliable batteries; and third, there are signs that new business models are emerging. These competencies and the know-how required must now be established in every part of the company. Success in this task will be a major factor in determining who the future players in the automotive industry will be. Achieving it is a strategic management task. - Suppliers and automakers must pool their resources if the European automotive industry

Adaptive powertrain control for plugin hybrid electric vehicles

Science.gov (United States)

Kedar-Dongarkar, Gurunath; Weslati, Feisel

2013-10-15

A powertrain control system for a plugin hybrid electric vehicle. The system comprises an adaptive charge sustaining controller; at least one internal data source connected to the adaptive charge sustaining controller; and a memory connected to the adaptive charge sustaining controller for storing data generated by the at least one internal data source. The adaptive charge sustaining controller is operable to select an operating mode of the vehicle's powertrain along a given route based on programming generated from data stored in the memory associated with that route. Further described is a method of adaptively controlling operation of a plugin hybrid electric vehicle powertrain comprising identifying a route being traveled, activating stored adaptive charge sustaining mode programming for the identified route and controlling operation of the powertrain along the identified route by selecting from a plurality of operational modes based on the stored adaptive charge sustaining mode programming.

A comprehensive overview of hybrid electric vehicle: Powertrain configurations, powertrain control techniques and electronic control units

Energy Technology Data Exchange (ETDEWEB)

Cagatay Bayindir, Kamil; Goezuekuecuek, Mehmet Ali; Teke, Ahmet [Cukurova University, Department of Electrical and Electronics Engineering, Balcali, Saricam, Adana (Turkey)

2011-02-15

The studies for hybrid electrical vehicle (HEV) have attracted considerable attention because of the necessity of developing alternative methods to generate energy for vehicles due to limited fuel based energy, global warming and exhaust emission limits in the last century. HEV incorporates internal composition engine, electric machines and power electronic equipments. In this study, overview of HEVs with a focus on hybrid configurations, energy management strategies and electronic control units are presented. Advantages and disadvantages of each configuration are clearly emphasized. The existing powertrain control techniques for HEVs are classified and comprehensively described. Electronic control units used in HEV configuration are also elaborated. The latest trends and technological challenges in the near future for HEVs are discussed. (author)

STUDIES AND EXPERIMENTAL RESEARCH CONCERNING THE PERFORMANCES OF THE INTERNAL COMBUSTION ENGINE, CONTROLLED OVER THE POWERTRAIN CONTROL MODULE

Directory of Open Access Journals (Sweden)

Narcis URICANU

2012-05-01

Full Text Available the paper present how can be controlled a road vehicle through a powertrain control module, a type of ECU, programmable ECU (Electronic Control Unit, when we want to increase the performances of the engine, compared with the standard performances of the engine. The programmable ECU is a control system which replaces the ECU from the vehicle and is able to manage, better than the standard ECU, the behaviour of the spark ignition engine on increasing the performances. Sports cars need to obtain the best performances from them engine, the specific regimes at which them must function impose certain limits which will be achieved during the competition. Nowadays the vehicles designers and engineering, working for the production cars, have adopted many solutions from the race cars area, due to the advantage offered by these elements (lightweight materials, fasts responses, high speeds and system like programmable ECU. To obtain more power on the engine, we have to find and applied the best solution concerning the internal combustion processes and the consequences concerning the exhaust. This papers present who can be increased the performances of the spark ignition engine through the air-flow ratio, controlled by the programmable ECU and with the sensors help, like water temperature sensor, intake air temperature sensor, throttle position sensor, lambda sensor

Method of electric powertrain matching for battery-powered electric cars

Science.gov (United States)

Ning, Guobao; Xiong, Lu; Zhang, Lijun; Yu, Zhuoping

2013-05-01

The current match method of electric powertrain still makes use of longitudinal dynamics, which can't realize maximum capacity for on-board energy storage unit and can't reach lowest equivalent fuel consumption as well. Another match method focuses on improving available space considering reasonable layout of vehicle to enlarge rated energy capacity for on-board energy storage unit, which can keep the longitudinal dynamics performance almost unchanged but can't reach lowest fuel consumption. Considering the characteristics of driving motor, method of electric powertrain matching utilizing conventional longitudinal dynamics for driving system and cut-and-try method for energy storage system is proposed for passenger cars converted from traditional ones. Through combining the utilization of vehicle space which contributes to the on-board energy amount, vehicle longitudinal performance requirements, vehicle equivalent fuel consumption level, passive safety requirements and maximum driving range requirement together, a comprehensive optimal match method of electric powertrain for battery-powered electric vehicle is raised. In simulation, the vehicle model and match method is built in Matlab/simulink, and the Environmental Protection Agency (EPA) Urban Dynamometer Driving Schedule (UDDS) is chosen as a test condition. The simulation results show that 2.62% of regenerative energy and 2% of energy storage efficiency are increased relative to the traditional method. The research conclusions provide theoretical and practical solutions for electric powertrain matching for modern battery-powered electric vehicles especially for those converted from traditional ones, and further enhance dynamics of electric vehicles.

Electrification of conventional powertrains. Challenges and opportunities; Elektrifizierung des konventionellen Antriebsstrangs. Herausforderungen und Potentiale

Energy Technology Data Exchange (ETDEWEB)

Bischoff, Claus; Abele, Marcus; Johannaber, Martin; Lingenfelser, Christian [Robert Bosch GmbH, Schwieberdingen (Germany)

2010-07-01

Even vehicles of the generation still have significant potential to increase the efficiency of the powertrain, the auxiliaries and the electrical system. Good examples are the advancement of the start/stop system, which enables a higher recuperation of braking energy, and the recovery of waste heat from the combustion engine. This contribution shows a methodology to identify the potentials in real vehicles through measurements and simulations both at system and component level. Technical solutions for powertrain electrification and overall energy management found with this methodology are presented. The focus of the innovation and development process is on technical solutions, which may have only a mean potential for CO{sub 2} reduction, but have high cost efficiency. Such cost-effective technologies enable a broad market penetration and the opportunity for the systematic combination in the vehicle, and thus making a significant positive influence on the CO{sub 2} fleet balance and conservation of resources. Finally it is demonstrated how the optimization of the powertrain efficiency, the electrical system and the auxiliaries can contribute to the technology development for future vehicle concepts such as electric vehicles. (orig.)

Integrated powertrain control for optimizing CO2-NOx emission trade-off in heavy duty hybrid electric vehicles

NARCIS (Netherlands)

Kessels, J.T.B.A.; Willems, F.P.T.; Spronkmans, S.J.

2011-01-01

Energy management in modern vehicles typically relates to optimizing the powerflow in the (hybrid) powertrain, whereas emission management is associated with the combustion engine and its aftertreatment system. To achieve maximum performance in both fuel economy and hazardous emissions, the concept

Intelligent sizing of a series hybrid electric power-train system based on Chaos-enhanced accelerated particle swarm optimization

International Nuclear Information System (INIS)

Zhou, Quan; Zhang, Wei; Cash, Scott; Olatunbosun, Oluremi; Xu, Hongming; Lu, Guoxiang

2017-01-01

Highlights: • A novel algorithm for hybrid electric powertrain intelligent sizing is introduced and applied. • The proposed CAPSO algorithm is capable of finding the real optimal result with much higher reputation. • Logistic mapping is the most effective strategy to build CAPSO. • The CAPSO gave more reliable results and increased the efficiency by 1.71%. - Abstract: This paper firstly proposed a novel HEV sizing method using the Chaos-enhanced Accelerated Particle Swarm Optimization (CAPSO) algorithm and secondly provided a demonstration on sizing a series hybrid electric powertrain with investigations of chaotic mapping strategies to achieve the global optimization. In this paper, the intelligent sizing of a series hybrid electric powertrain is formulated as an integer multi-objective optimization issue by modelling the powertrain system. The intelligent sizing mechanism based on APSO is then introduced, and 4 types of the most effective chaotic mapping strategy are investigated to upgrade the standard APSO into CAPSO algorithms for intelligent sizing. The evaluation of the intelligent sizing systems based on standard APSO and CAPSOs are then performed. The Monte Carlo analysis and reputation evaluation indicate that the CAPSO outperforms the standard APSO for finding the real optimal sizing result with much higher reputation, and CAPSO with logistic mapping strategy is the most effective algorithm for HEV powertrain components intelligent sizing. In addition, this paper also performs the sensitivity analysis and Pareto analysis to help engineers customize the intelligent sizing system.

New high pressure die cast magnesium alloy AM-HP2 for powertrain applications

Energy Technology Data Exchange (ETDEWEB)

Gibson, M.A. [Queensland Univ., Brisbane (Australia). CAST CRC]|[CSIRO Manufacturing and Materials Technology, Clayton (Australia); Zhu, S.M.; Nie, J.F. [Queensland Univ., Brisbane (Australia). CAST CRC]|[Monash Univ., Monash (Australia). Dept. of Materials Engineering

2007-07-01

In order to improve the benefits available through weight savings on engine emissions, magnesium alloys must gain wider acceptance in transmission and engine applications. This paper provided details of a new alloy with exceptional creep properties developed for automotive powertrain applications. The AM-HP2 alloy was developed as part of a broader research program investigating the relationship between the composition, structure and properties of magnesium rare earth (Mg-RE) based alloys and high-pressure die casting (HPDC). Cylindrical test specimens of various alloys were produced on a cold chamber HPDC machine. Tensile creep tests were then conducted under a constant load at 177 degrees C for a period of 600 hours. Microstructures of specimens were characterized using a CM20 transmission electron microscope. Results of the tests indicated that near-grain boundary microstructure was an important parameter in securing optimum elevated temperature properties. The RE element had a significant effect on the creep behaviour of the HPDC Mg-RE alloys. It was concluded that further research is needed to investigate the influence of the RE mixture in improving creep performance. 15 refs., 2 tabs., 6 figs.

Friction Reduction in Powertrain Materials: Role of Tribolayers

Science.gov (United States)

Banerji, Anindya

This study aims at understanding the micromechanisms responsible for reduction in friction and wear in the engine cylinder bore/liner materials when tested under lubricated and unlubricated conditions. The tribolayers formed in-situ during sliding contact are unique to each tribosystem and a detailed study of these tribolayers will shed light on the friction reduction mechanisms in powertrain materials. Boundary lubricated tribological performance of grey cast iron (CI) tested against non-hydrogenated diamond-like carbon coating (NH-DLC) resulted in 21% lower coefficient of friction (COF) and an order of magnitude lower volumetric wear compared to CI and steel counterfaces. Dilution of the engine oil by ethanol containing E85 biofuel, consisting of 85% ethanol and 15% gasoline, was beneficial as COF and volumetric wear losses were further reduced. TEM/EELS studies of the NH-DLC counterface provided evidence for OH adsorption of the dangling carbon bonds at the coating surface leading to low friction. Advantage of E85/engine oil blend was also evident during boundary lubricated sliding of eutectic Al-12.6% Si alloy against AISI 52100 steel. The oil residue layer (ORL) formed during boundary lubricated sliding incorporated nanocrystalline regions of Al, Si, ZnS, AlPO4 and ZnO surrounded by amorphous carbon regions. Higher proportions of Zn, S, and P antiwear compounds formed in the ORL when tested using the E85/oil (1:1) blend compared to the unmixed engine oil as the hydroxyl groups in ethanol molecules facilitated ZDDP degradation. Mico-Raman spectroscopy indicated two types of tribolayers formed during unlubricated sliding of thermally sprayed low carbon steel 1010 coating deposited on linerless Al 380 cylinder bore: i) Fe2O3 layer transformed from FeO during dry sliding and ii) Fe2O3 layer with a top amorphous carbon transfer layer when run against H-DLC coated TCR with COF of 0.18. The NH- and H-DLC coatings, that provide low friction under room temperature

Powertrain system for a hybrid electric vehicle

Science.gov (United States)

Reed, Jr., Richard G.; Boberg, Evan S.; Lawrie, Robert E.; Castaing, Francois J.

1999-08-31

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration.

Powertrain system for a hybrid electric vehicle

Science.gov (United States)

Reed, R.G. Jr.; Boberg, E.S.; Lawrie, R.E.; Castaing, F.J.

1999-08-31

A hybrid electric powertrain system is provided including an electric motor/generator drivingly engaged with the drive shaft of a transmission. The electric is utilized for synchronizing the rotation of the drive shaft with the driven shaft during gear shift operations. In addition, a mild hybrid concept is provided which utilizes a smaller electric motor than typical hybrid powertrain systems. Because the electric motor is drivingly engaged with the drive shaft of the transmission, the electric motor/generator is driven at high speed even when the vehicle speed is low so that the electric motor/generator provides more efficient regeneration. 34 figs.

Design of a low-cost hybrid powertrain with large fuel savings

NARCIS (Netherlands)

Berkel, van K.; Romers, L.H.J.; Vroemen, B.G.; Hofman, T.; Steinbuch, M.

2010-01-01

This paper presents a new design of a low-cost hybrid powertrain with large fuel savings. The hybrid powertrain contains only low-cost mechanical components, such as a flywheel module and a continuously variable transmission (CVT). Noelectrical motor/generator or battery is used. Based on

Method for controlling powertrain pumps

Science.gov (United States)

Sime, Karl Andrew; Spohn, Brian L; Demirovic, Besim; Martini, Ryan D; Miller, Jean Marie

2013-10-22

A method of controlling a pump supplying a fluid to a transmission includes sensing a requested power and an excess power for a powertrain. The requested power substantially meets the needs of the powertrain, while the excess power is not part of the requested power. The method includes sensing a triggering condition in response to the ability to convert the excess power into heat in the transmission, and determining that an operating temperature of the transmission is below a maximum. The method also includes determining a calibrated baseline and a dissipation command for the pump. The calibrated baseline command is configured to supply the fluid based upon the requested power, and the dissipation command is configured to supply additional fluid and consume the excess power with the pump. The method operates the pump at a combined command, which is equal to the calibrated baseline command plus the dissipation command.

Simultaneous Observation of Hybrid States for Cyber-Physical Systems: A Case Study of Electric Vehicle Powertrain.

Science.gov (United States)

Lv, Chen; Liu, Yahui; Hu, Xiaosong; Guo, Hongyan; Cao, Dongpu; Wang, Fei-Yue

2017-08-22

As a typical cyber-physical system (CPS), electrified vehicle becomes a hot research topic due to its high efficiency and low emissions. In order to develop advanced electric powertrains, accurate estimations of the unmeasurable hybrid states, including discrete backlash nonlinearity and continuous half-shaft torque, are of great importance. In this paper, a novel estimation algorithm for simultaneously identifying the backlash position and half-shaft torque of an electric powertrain is proposed using a hybrid system approach. System models, including the electric powertrain and vehicle dynamics models, are established considering the drivetrain backlash and flexibility, and also calibrated and validated using vehicle road testing data. Based on the developed system models, the powertrain behavior is represented using hybrid automata according to the piecewise affine property of the backlash dynamics. A hybrid-state observer, which is comprised of a discrete-state observer and a continuous-state observer, is designed for the simultaneous estimation of the backlash position and half-shaft torque. In order to guarantee the stability and reachability, the convergence property of the proposed observer is investigated. The proposed observer are validated under highly dynamical transitions of vehicle states. The validation results demonstrates the feasibility and effectiveness of the proposed hybrid-state observer.

Development of an efficient and compact range extender engine; Entwicklung eines effizienten und kompakten Range-Extender-Motors

Energy Technology Data Exchange (ETDEWEB)

Mahr, Bernd; Bassett, Mike; Hall, Jonathan; Warth, Marco [Mahle Powertrain Ltd., Northampton (United Kingdom)

2011-10-15

Mahle Powertrain has developed a compact, two-cylinder, spark-ignition engine that is specifically designed to be used as a range extender. Drive-cycle simulations and engine tests indicate that a range-extended vehicle using this engine would achieve a significant reduction in fuel consumption and tail-pipe CO{sub 2} levels. (orig.)

Performance and energy management of a novel full hybrid electric powertrain system

International Nuclear Information System (INIS)

Chung, Cheng-Ta; Hung, Yi-Hsuan

2015-01-01

This study compared the performance and energy management between a novel full hybrid electric powertrain and a traditional power-split hybrid system. The developed planetary gearset and dual clutch configuration provides five operation modes. Equations for the torque and speed of power sources for the planetary gearset and dual clutch system and the Toyota Hybrid System are firstly derived. By giving vehicle performance of gradability, maximal speeds in hybrid and pure electric modes, the power sources of the 210 kg target vehicle are: a 125 cc engine and two 1.8 kW motor and generator. The optimal tank-to-wheel efficiencies, ratios of circulating power, and operation points at specific vehicle speeds and out loads are calculated. Simulation results show that the dual-motor electric vehicle mode offers superior performance regarding electric drive; the low capacity of the battery is conducive to reducing manufacturing and maintenance costs; the tank-to-wheel efficiency is mainly operated above 20% while the power split electronic-continuously-variable-transmission mode is the major operation mode, and a maximum of 17% fuel economy improvement is achieved compared with the Toyota Hybrid System in most of the vehicle speed ranges. The outstanding performance warrants further real-system development, especially regarding the implementation in plug-in and sport hybrid powertrain designs. - Highlights: • An innovative power split hybrid powertrain was designed. • Dual-motor electric-vehicle mode highlighted for plug-in function. • Power circulation ratios and five driving modes were analyzed. • Global search method utilized for optimal energy management. • Maximal 17+% fuel improvement compared to Toyota Hybrid System

Adaptive Engine Torque Compensation with Driveline Model

Directory of Open Access Journals (Sweden)

Park Jinrak

2018-01-01

Full Text Available Engine net torque is the total torque generated by the engine side, and includes the fuel combustion torque, the friction torque, and additionally the starter motor torque in case of hybrid vehicles. The engine net torque is utilized to control powertrain items such as the engine itself, the transmission clutch, also the engine clutch, and it must be accurate for the precise powertrain control. However, this net torque can vary with the engine operating conditions like the engine wear, the changes of the atmospheric pressure and the friction torque. Thus, this paper proposes the adaptive engine net torque compensator using driveline model which can cope with the net torque change according to engine operating conditions. The adaptive compensator was applied on the parallel hybrid vehicle and investigated via MATLAB Simcape Driveline simulation.

Model-based design of active vibration compensation in the passenger car powertrain; Modellbasierte Auslegung der aktiven Schwingungskompensation im Kfz-Antriebsstrang

Energy Technology Data Exchange (ETDEWEB)

Quernheim, L.

2008-07-01

Modern passenger cars have increasingly higher driving torques while the rotary mass of the powertrain is reduced. This induces vibrations. Especially during load change operations, the driving comfort may therefore be impaired by jolting. To reduce these vibrations, the engine control unit has integrated control functions that influence the driving characteristics. Until now, these control functions were adjusted empirically by the application engineer during time-consuming test drives, but this option is failing as development times are getting shorter while there are increasing numbers of car lines. The author therefore presents a new option, i.e. optimisation of the comfort functions by means of model-based control unit design. The example of an active vibration damper is presented to illustrate this model-based procedure, and vehicle analyses were carried out with the intention to show that this method supports the application engineer in his work efficiently. (orig.)

The Nissan LEAF electric powertrain

Energy Technology Data Exchange (ETDEWEB)

Nakazawa, Shinsuke [Nissan Motor Co., Ltd. (Japan)

2011-07-01

The need for CO{sub 2} reduction as a countermeasure to global warming, and to move away from our dependence on fossil fuels as a countermeasure to energy security are urgent issues. One of the ultimate goals to achieving these targets is to develop a 'Zero emission car' such as an electric vehicle or a fuel cell vehicle, along with the manufacturing of clean energy. Nissan have developed a new powertrain for the electric vehicle, and have installed it in the Nissan LEAF. Sales of the Nissan LEAF started in North America, Europe and Japan in 2010, with plans to sell it globally by 2012. In order to achieve an improved driving range, power performance and drivability performance, Nissan have adapted a high efficiency synchronous motor, a water-cooled inverter, and reducer. Moreover, the Nissan LEAF has the capability of a 3.3kW AC charge and a 50kW DC quick charge. This presentation will introduce the features of the electric powertrain adopted for Nissan LEAF. (orig.)

U.S. Army Hybrid Propulsion System R&D Overview ATA/Technology & Maintenance Council 2011 Fall Meeting, Hybrid Powertrain Task Force Session

Science.gov (United States)

2011-09-19

and CVTS – HHO Technology – Start-Stop & Idle Stop Accessories – Pulse Jet Air Cleaner Ultra – Hybrid Energy Module (HEM) for Electric and Hybrid...The engine will meet 2010 EPA emission requirements – Hybrid drive powertrain; a 160 Horsepower (Hp) electric machine used for propulsion and

System design and energetic characterization of a four-wheel-driven series–parallel hybrid electric powertrain for heavy-duty applications

International Nuclear Information System (INIS)

Wang, Enhua; Guo, Di; Yang, Fuyuan

2015-01-01

Highlights: • A novel four-wheel-driven series–parallel hybrid powertrain is proposed. • A system model and a rule-based control strategy are designed. • Energetic performance is compared to a rear-wheel-driven hybrid powertrain. • Less torsional oscillation and more robust regenerative braking are achieved. - Abstract: Powertrain topology design is vital for system performance of a hybrid electric vehicle. In this paper, a novel four-wheel-driven series–parallel hybrid electric powertrain is proposed. A motor is connected to the differential of the rear axle. An auxiliary power unit is linked to the differential of the front axle via a clutch. First, a mathematical model was established to evaluate the fuel-saving potential. A rule-based energy management algorithm was subsequently designed, and its working parameters were optimized. The hybrid powertrain system was applied to a transit bus, and the system characteristics were analyzed. Compared to an existing coaxial power-split hybrid powertrain, the fuel economy of the four-wheel-driven series–parallel hybrid powertrain can be at the same level under normal road conditions. However, the proposed four-wheel-driven series–parallel hybrid powertrain can recover braking energy more efficiently under road conditions with a low adhesive coefficient and can alleviate the torsional oscillation occurring at the existing coaxial power-split hybrid powertrain. Therefore, the four-wheel-driven series–parallel hybrid powertrain is a good solution for transit buses toward more robust performance.

The $2000 Electric Powertrain Option-1 Program. Final technical report

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

This report describes the tasks accomplished as part of Northrop Grumman's TRP $2000 Electric Powertrain Option-1 program. Northrop Grumman has strived to achieve technology advances and development considered as high priority to the success of future electric vehicles. Northrop Grumman has achieved the intent of the program by taking several steps toward reducing the cost of the electric vehicle powertrain, demonstrating technologies in the form of hardware and introducing enhancements into production that are consistent with the needs of the market.

Design, analysis and modeling of a novel hybrid powertrain system based on hybridized automated manual transmission

Science.gov (United States)

Wu, Guang; Dong, Zuomin

2017-09-01

Hybrid electric vehicles are widely accepted as a promising short to mid-term technical solution due to noticeably improved efficiency and lower emissions at competitive costs. In recent years, various hybrid powertrain systems were proposed and implemented based on different types of conventional transmission. Power-split system, including Toyota Hybrid System and Ford Hybrid System, are well-known examples. However, their relatively low torque capacity, and the drive of alternative and more advanced designs encouraged other innovative hybrid system designs. In this work, a new type of hybrid powertrain system based hybridized automated manual transmission (HAMT) is proposed. By using the concept of torque gap filler (TGF), this new hybrid powertrain type has the potential to overcome issue of torque gap during gearshift. The HAMT design (patent pending) is described in details, from gear layout and design of gear ratios (EV mode and HEV mode) to torque paths at different gears. As an analytical tool, mutli-body model of vehicle equipped with this HAMT was built to analyze powertrain dynamics at various steady and transient modes. A gearshift was decomposed and analyzed based basic modes. Furthermore, a Simulink-SimDriveline hybrid vehicle model was built for the new transmission, driveline and vehicle modular. Control strategy has also been built to harmonically coordinate different powertrain components to realize TGF function. A vehicle launch simulation test has been completed under 30% of accelerator pedal position to reveal details during gearshift. Simulation results showed that this HAMT can eliminate most torque gap that has been persistent issue of traditional AMT, improving both drivability and performance. This work demonstrated a new type of transmission that features high torque capacity, high efficiency and improved drivability.

Global powertrains - the GM case; Globale Antriebssysteme - Die Strategie von GM

Energy Technology Data Exchange (ETDEWEB)

Johansson, R.J. [General Motors Powertrain Europe, Turin (Italy)

2006-07-01

In today's environment the development of vehicles is confronted with very high customer expectations and legislative restrictions, which can only be fulfilled with a high technological effort and profound know how. These challenges are further increased due to the diversity of markets with regional preferences and increased cost and demand for energy. At the same time it is a principle for General Motors to offer our customers a sustainable and economical individual mobility. The worldwide development strategy of GM powertrain is following exactly this philosophy: efficient and and cost-effective technologies are being developed for gasoline and diesel engines in order to fulfill all of todays and all prognosed future requirements. Based on this GM has defined it's longterm strategy, the march to zero, which includes alternative propulsion systems with the ultimate goal of the neutral emission vehicle with ensured energy supply. With a unique worldwide development network GM is in an optimal position to take on this challenge. Already today GM is successfully using the synergies of competence centers all over the world for the global development strategy. Modern powertrains are based on a common structure but allow regional adaptation to all markets by using a modular system. This development philosophy is one of the cornerstones for General Motors position as the world's largest carmaker. (orig.)

Study on the economic and environmental benefits of different EV powertrain topologies

International Nuclear Information System (INIS)

Wang, Bin; Xu, Min; Yang, Li

2014-01-01

Highlights: • EV powertrain topologies can be realized by flexible distributed electric motors. • Model-based design optimization method is used to analyze and evaluate the EV. • The wheel-hub drive with reducer possesses the most competitive advantages. • US06 and NYCC result in the deterioration of EVs’ cost and GHG emissions. - Abstract: Numerous feasible schemes of powertrain topology can be designed for the electric vehicles (EVs) based on the distributed configurations of the electric motors. In this study, the effects of different EV powertrain topologies on the energy efficiency, vehicle ownership cost and lifecycle greenhouse gas (GHG) emissions of EVs are investigated. Energy-based vehicle simulation model including the regenerative braking function and battery degradation prediction method is established firstly. An optimization scheme combining the energy-based vehicle simulation model is conducted to minimize the electric energy consumption under various scenarios and driving conditions. Then the vehicle ownership cost and lifecycle GHG emissions of EVs are evaluated based on Chinese EV market and electricity grid. The sensitivity analyses of EV powertrain topology are implemented based on the different vehicle weights, CO 2 intensities of electricity and all-electric ranges. Results show that EVs using the powertrain of wheel-hub drive with the gear reducer have lower energy consumption. Furthermore, the driving cycles with more aggressive acceleration/deceleration and frequently stop-and-go conditions can increase both the vehicle ownership cost and lifecycle GHG emissions simultaneously. Chinese city traffic conditions will help EVs to obtain more benefits in respect of the economy and environment

Internal combustion engines in hybrid vehicles

NARCIS (Netherlands)

Mourad, S.; Weijer, C.J.T. van de; Beckman, D.E.

1998-01-01

In this paper the use of internal combustion engines in hybrid powertrains is investigated. The substantial difference between the use of internal combustion engines in conventional and in hybrid vehicles mean that engines for hybrid vehicles should be designed specifically for the purpose. At the

FY 2007 Progress Report for Advanced Combustion Engine Technologies

Energy Technology Data Exchange (ETDEWEB)

None, None

2007-12-01

Advanced combustion engines have great potential for achieving dramatic energy efficiency improvements in light-duty vehicle applications, where it is suited to both conventional and hybrid- electric powertrain configurations. Light-duty vehicles with advanced combustion engines can compete directly with gasoline engine hybrid vehicles in terms of fuel economy and consumer-friendly driving characteristics; also, they are projected to have energy efficiencies that are competitive with hydrogen fuel cell vehicles when used in hybrid applications.Advanced engine technologies being researched and developed by the Advanced Combustion Engine R&D Sub-Program will also allow the use of hydrogen as a fuel in ICEs and will provide an energy-efficient interim hydrogen-based powertrain technology during the transition to hydrogen/fuelcell-powered transportation vehicles.

Hybrid vehicle powertrain system with power take-off driven vehicle accessory

Science.gov (United States)

Beaty, Kevin D.; Bockelmann, Thomas R.; Zou, Zhanijang; Hope, Mark E.; Kang, Xiaosong; Carpenter, Jeffrey L.

2006-09-12

A hybrid vehicle powertrain system includes a first prime mover, a first prime mover driven power transmission mechanism having a power take-off adapted to drive a vehicle accessory, and a second prime mover. The second prime mover is operable to drive the power transmission mechanism alone or in combination with the first prime mover to provide power to the power take-off through the power transmission mechanism. The invention further includes methods for operating a hybrid vehicle powertrain system.

Current hybrid-electric powertrain architectures: Applying empirical design data to life cycle assessment and whole-life cost analysis

International Nuclear Information System (INIS)

Hutchinson, Tim; Burgess, Stuart; Herrmann, Guido

2014-01-01

Highlights: • Design data for 44 hybrid cars available in the US has been gathered and analysed. • An empirical life cycle assessment of greenhouse gas emissions is performed. • Empirical whole-life cost modelling is used to evaluate powertrain architectures. • The value to be seen in each architecture is highly dependent on its application. • Mild, HSD and Plug-in HSD powertrains are the most likely architectures to dominate. - Abstract: The recent introduction of hybrid-electric powertrain technology has disrupted the automotive industry, causing significant powertrain design divergence. As this radical powertrain innovation matures, will hybrid vehicles dominate the future automotive market and does this represent a positive shift in the environmental impact of the industry? The answer to this question is sought within this paper. It seeks to take advantage of the position that the industry has reached, replacing previous theoretical studies with the first extensive empirical models of life cycle emissions and whole-life costing. A comprehensive snapshot of today’s hybrid market is presented, with detailed descriptions of the various hybrid powertrain architectures. Design data has been gathered for 44 hybrid passenger cars currently available in the US. The empirical data is used to explore the relative life cycle greenhouse gas emissions and whole-life costing of different hybrid powertrain architectures. Potential dominant designs are identified and their emissions are shown to be reduced. However, both the emissions and economic competitiveness of different hybrid powertrains are shown to vary significantly depending on how the vehicle is used

Real-Time Energy Management Control for Hybrid Electric Powertrains

Directory of Open Access Journals (Sweden)

Mohamed Zaher

2013-01-01

Full Text Available This paper focuses on embedded control of a hybrid powertrain concepts for mobile vehicle applications. Optimal robust control approach is used to develop a real-time energy management strategy. The main idea is to store the normally wasted mechanical regenerative energy in energy storage devices for later usage. The regenerative energy recovery opportunity exists in any condition where the speed of motion is in the opposite direction to the applied force or torque. This is the case when the vehicle is braking, decelerating, the motion is driven by gravitational force, or load driven. There are three main concepts for energy storing devices in hybrid vehicles: electric, hydraulic, and mechanical (flywheel. The real-time control challenge is to balance the system power demands from the engine and the hybrid storage device, without depleting the energy storage device or stalling the engine in any work cycle. In the worst-case scenario, only the engine is used and the hybrid system is completely disabled. A rule-based control algorithm is developed and is tuned for different work cycles and could be linked to a gain scheduling algorithm. A gain scheduling algorithm identifies the cycle being performed by the work machine and its position via GPS and maps both of them to the gains.

A MultiAir®/MultiFuel Approach to Enhancing Engine System Efficiency

Energy Technology Data Exchange (ETDEWEB)

Reese, Ronald [Chrysler Group LLC., Auburn Hills, MI (United States)

2015-05-20

FCA US LLC (formally known as Chrysler Group LLC, and hereinafter “Chrysler”) was awarded an American Recovery and Reinvestment Act (ARRA) funded project by the Department of Energy (DOE) titled “A MultiAir®/MultiFuel Approach to Enhancing Engine System Efficiency” (hereinafter “project”). This award was issued after Chrysler submitted a proposal for Funding Opportunity Announcement DE-FOA- 0000079, “Systems Level Technology Development, Integration, and Demonstration for Efficient Class 8 Trucks (SuperTruck) and Advanced Technology Powertrains for Light-Duty Vehicles (ATP-LD).” Chrysler started work on this project on June 01, 2010 and completed testing activities on August 30, 2014. Overall objectives of this project were; Demonstrate a 25% improvement in combined Federal Test Procedure (FTP) City and Highway fuel economy over a 2009 Chrysler minivan; Accelerate the development of highly efficient engine and powertrain systems for light-duty vehicles, while meeting future emissions standards; and Create and retain jobs in accordance with the American Recovery and Reinvestment Act of 2009

Argonne to open new facility for advanced vehicle testing

CERN Multimedia

2002-01-01

Argonne National Laboratory will open it's Advanced Powertrain Research Facility on Friday, Nov. 15. The facility is North America's only public testing facility for engines, fuel cells, electric drives and energy storage. State-of-the-art performance and emissions measurement equipment is available to support model development and technology validation (1 page).

Multi-objective component sizing of a power-split plug-in hybrid electric vehicle powertrain using Pareto-based natural optimization machines

Science.gov (United States)

Mozaffari, Ahmad; Vajedi, Mahyar; Chehresaz, Maryyeh; Azad, Nasser L.

2016-03-01

The urgent need to meet increasingly tight environmental regulations and new fuel economy requirements has motivated system science researchers and automotive engineers to take advantage of emerging computational techniques to further advance hybrid electric vehicle and plug-in hybrid electric vehicle (PHEV) designs. In particular, research has focused on vehicle powertrain system design optimization, to reduce the fuel consumption and total energy cost while improving the vehicle's driving performance. In this work, two different natural optimization machines, namely the synchronous self-learning Pareto strategy and the elitism non-dominated sorting genetic algorithm, are implemented for component sizing of a specific power-split PHEV platform with a Toyota plug-in Prius as the baseline vehicle. To do this, a high-fidelity model of the Toyota plug-in Prius is employed for the numerical experiments using the Autonomie simulation software. Based on the simulation results, it is demonstrated that Pareto-based algorithms can successfully optimize the design parameters of the vehicle powertrain.

Towards Integrated Powertrain Control: exploiting synergy between a diesel hybrid and aftertreatment system in a distribution truck

NARCIS (Netherlands)

Foster, D.L.; Cloudt, R.P.M.; Willems, F.P.T.

2008-01-01

With the increasing demands on driveability, fuel efficiency and emissions, it becomes essential to optimize the overall performance of future powertrains. Therefore, a system approach is required. In this study, the Integrated Powertrain Control concept is presented, which exploits the synergy

Towards Integrated Powertrain Control : exploiting synergy between a diesel hybrid and aftertreatment system in a distribution truck

NARCIS (Netherlands)

Foster, D.; Cloudt, R.P.M.; Willems, F.P.T.

2008-01-01

With the increasing demands on driveability, fuel efficiency and emissions, it becomes essential to optimize the overall performance of future powertrains. Therefore, a system approach is required. In this study, the Integrated Powertrain Control concept is presented, which exploits the synergy

A conceptual design of main components sizing for UMT PHEV powertrain

Science.gov (United States)

Haezah, M. N.; Norbakyah, J. S.; Atiq, W. H.; Salisa, A. R.

2015-12-01

This paper presents a conceptual design of main components sizing for Universiti Malaysia Terengganu plug-in hybrid electric vehicle (UMT PHEV) powertrain. In the design of hybrid vehicles, it is important to identify a proper component sizes. Component sizing significantly affects vehicle performance, fuel economy and emissions. The proposed UMT PHEV has only one electric machine (EM) which functions as either a motor or generator at a time and using batteries and ultracapacitors as an energy storage system (ESS). In this work, firstly, energy and power requirements based on parameters, specifications and performance requirements of vehicle are calculated. Then, the parameters for internal combustion engine, EM and ESS are selected based on the developed Kuala Terengganu drive cycle. The results obtained from this analysis are within reasonable range and satisfactory.

A study on the role of powertrain system dynamics on vehicle driveability

Science.gov (United States)

Castellazzi, Luca; Tonoli, Andrea; Amati, Nicola; Galliera, Enrico

2017-07-01

Vehicle driveability describes the complex interactions between the driver and the vehicle, mainly related to longitudinal vibrations. Today, a relevant part of the driveability process optimisation is realised by means of track tests, which require a considerable effort due to the number of parameters (such as stiffness and damping components) affecting this behaviour. The drawback of this approach is that it is carried on at a stage when a design iteration becomes very expensive in terms of time and cost. The objective of this work is to propose a light and accurate tool to represent the relevant quantities involved in the driveability analysis, and to understand which are the main vehicle parameters that influence the torsional vibrations transmitted to the driver. Particular attention is devoted to the role of the tyre, the engine mount, the dual mass flywheel and their possible interactions. The presented nonlinear dynamic model has been validated in time and frequency domain and, through linearisation of its nonlinear components, allows to exploit modal and energy analysis. Objective indexes regarding the driving comfort are additionally considered in order to evaluate possible driveability improvements related to the sensitivity of powertrain parameters.

Life cycle cost analysis of a car, a city bus and an intercity bus powertrain for year 2005 and 2020

International Nuclear Information System (INIS)

Hellgren, Jonas

2007-01-01

The international economy, in the beginning of the 20th century, is characterized by uncertainty about the supply and the price of oil. Together with the fast decrease of electrical propulsion component prices, it becomes more and more cost effective to develop vehicles with alternative powertrains. This paper focuses on two questions: Are alternative powertrains especially cost effective for specific applications?; How does an increased fossil fuel price influences the choose of powertrain? To assess these questions, a computer tool named THEPS, developed in a Ph.D. project, is used. Three applications and three scenarios are analysed. The applications, a car, a city bus and an intercity bus, are vehicles all assumed to operate in Sweden. One scenario represents year 2005, the other two year 2020. The two future scenarios are characterized by different fossil fuel prices. The study, presented in the paper, indicates that alternative powertrains can be competitive from a cost perspective, in some applications, already in year 2005. It is for example cost effective to equip a city bus, running in countries with a high fuel price, with a hybrid powertrain. The study also indicates that pure electric, hybrid and/or fuel cell cars will probably be a more cost effective choice than conventional cars in year 2020. Another indication is that it will not be clear which powertrain concept to choose. The reason is that many cost effective powertrain concepts will be offered. The best choice will depend on the application

Method and apparatus for operating a powertrain system upon detecting a stuck-closed clutch

Science.gov (United States)

Hansen, R. Anthony

2014-02-18

A powertrain system includes a multi-mode transmission having a plurality of torque machines. A method for controlling the powertrain system includes identifying all presently applied clutches including commanded applied clutches and the stuck-closed clutch upon detecting one of the torque-transfer clutches is in a stuck-closed condition. A closed-loop control system is employed to control operation of the multi-mode transmission accounting for all the presently applied clutches.

Analysis process and the dimensioning direction of the Powertrain project for the best vehicle fuel consumption; Processo de analise e direcionamento de projeto de powertrain para o melhor consumo de combustivel veicular

Energy Technology Data Exchange (ETDEWEB)

Rupcic, Jorge Radosevic [Fiat GM Powertrain Ltda. (Brazil); Massarani, Marcelo [Sao Paulo Univ., SP (Brazil). Escola Politecnica

2006-07-01

This paper presents the viability analysis methodology of powertrain project aiming the improvement the vehicle fuel consumption. The object of this work is the definition which powertrains architecture results in the best vehicle fuel consumption and to know the impact on the enterprise, considering to offer flexibility for allowing the successive increment when new technologies are required without high resources and yet offering performance gains that maintain the vehicle on competitive level and well accepted by the customers.

Time-varying delays compensation algorithm for powertrain active damping of an electrified vehicle equipped with an axle motor during regenerative braking

Science.gov (United States)

Zhang, Junzhi; Li, Yutong; Lv, Chen; Gou, Jinfang; Yuan, Ye

2017-03-01

The flexibility of the electrified powertrain system elicits a negative effect upon the cooperative control performance between regenerative and hydraulic braking and the active damping control performance. Meanwhile, the connections among sensors, controllers, and actuators are realized via network communication, i.e., controller area network (CAN), that introduces time-varying delays and deteriorates the control performances of the closed-loop control systems. As such, the goal of this paper is to develop a control algorithm to cope with all these challenges. To this end, the models of the stochastic network induced time-varying delays, based on a real in-vehicle network topology and on a flexible electrified powertrain, were firstly built. In order to further enhance the control performances of active damping and cooperative control of regenerative and hydraulic braking, the time-varying delays compensation algorithm for the electrified powertrain active damping during regenerative braking was developed based on a predictive scheme. The augmented system is constructed and the H∞ performance is analyzed. Based on this analysis, the control gains are derived by solving a nonlinear minimization problem. The simulations and hardware-in-loop (HIL) tests were carried out to validate the effectiveness of the developed algorithm. The test results show that the active damping and cooperative control performances are enhanced significantly.

Communication for powertrains - development methods illustrated by the example of a hybrid drive; Kommunikation fuer Fahrantriebe - Entwicklungsmethoden am Beispiel eines Hybridantriebs

Energy Technology Data Exchange (ETDEWEB)

Anderl, T.

2006-07-01

Future communication systems of integrated powertrains will have to cope with more data with higher relevance in terms of functionality, safety and availability. For this, after a description of control systems and relevant bus systems (CAN, FlexRay etc.), the author presents suggestions for customised model-based development of networks for powertrain systems. Based on measurements on a prototype passenger car with continuous parallel hybrid drive, a failure-tolerant communication system with two dynamically redundant CAN channels was developed. Functional and integration tests are carried out using hardware-in-the-loop simulations, and system and component reactions are identified in case of critical failure scenarios. (orig.)

Comparative study on performances of a continuously variable transmission used in two different powertrain architectures

Science.gov (United States)

Sibiceanu, A. R.; Ivan, F.; Nicolae, V.; Iorga, A.; Cioroianu, C.

2017-08-01

Given the importance of reducing carbon emissions from road transport, price and security of oil supply, hybrid electric vehicle can provide a viable alternative solution to conventional vehicles, equipped with thermal engines, which use fossil fuels. Based on the growing trends of new vehicles sales, which include hybrid and electric vehicles closely associated with their use in terms of harmful emissions, strict regulations are established. In this paper were created models of thermal and hybrid electric powertrains groups, using computer simulation program AVL Cruise, making a comparative study using petroleum fuels for continuously variable transmission. The results obtained highlights both fuel consumption as well as pollutant emissions.

Efficient Electric Powertrain with externally excited synchronous machine without rare earth magnets using the example of the Renault system solution; Effizienter Elektroantrieb mit fremderregter Synchronmaschine ohne seltene Erden am Beispiel der Renault Systemloesung

Energy Technology Data Exchange (ETDEWEB)

Fennel, H.; Hakvoort, H. [Continental, Nuernberg (Germany); Hackmann, W. [Continental, Berlin (Germany); Vignaud, A.; Forin-Crouvoisier, L. [Renault, Guyancourt (France)

2012-11-01

The Renault Fluence Z.E. and Kangoo Z.E. electric vehicles were launched in mass production in 2011 with an innovative electric power-train. The vehicles show high performance, reliability and comfort and this without any emission and nearly no engine noise. The potential market, taken into account driver usage patterns, autonomy and vehicle price, would already exceed three million electric vehicles. The electric powertrain consists of an externally excited synchronous machine and the second generation power electronics developed and produced by Continental. The powertrain ensures a good compromise between efficiency requirements and cost, especially facing the actual fluctuation of the permanent magnet price. Additionally the approach of a compact axle drive unit, including electric motor and gears, is an effective solution to reduce overall system cost. State of the art safety norms are fulfilled for which the independent shutoff paths of stator and rotor are beneficial. Further standardization is the key to reduce costs. (orig.)

Causal Tracking Control of a Non-Minimum Phase HIL Transmission Test System

OpenAIRE

Wang, Pengfei

2009-01-01

The automotive industry has long relied on testing powertrain components in real vehicles, which causes the development process to be slow and expensive. Therefore, hardware in the loop (HIL) testing techniques are increasingly being adopted to develop electronic control units (ECU) for engine and other components of a vehicle. In this thesis, HIL testing system is developed to provide a laboratory testing environment for continuously variable transmissions (CVTs). Two induction motors were u...

EPA ALPHA Modeling of a Conventional Mid-Size Car with CVT and Comparable Powertrain Technologies (SAE 2016-01-1141)

Science.gov (United States)

This paper presents the testing and ALPHA modeling of a CVT-equipped 2013 Nissan Altima 2.5S using comparable powertrain technology inputs in the effort to model the current and future U.S. light-duty vehicle fleet approximated using components with comparable levels of performan...

Hybrid powertrain system

Science.gov (United States)

Grillo, Ricardo C.; O'Neil, Walter K.; Preston, David M.

2005-09-20

A hybrid powertrain system is provided that includes a first prime mover having a rotational output, a second prime mover having a rotational output, and a transmission having a main shaft supporting at least two main shaft gears thereon. The transmission includes a first independent countershaft drivingly connected to the first prime mover and including at least one ratio gear supported thereon that meshes with a respective main shaft gear. A second independent countershaft is drivingly connected to the second prime mover and includes at least one ratio gear supported thereon that meshes with a respective main shaft gear. The ratio gears on the first and second countershafts cooperate with the main shaft gears to provide at least one gear ratio between the first and second countershafts and the main shaft. A shift control mechanism selectively engages and disengages the first and second countershafts for rotation with the main shaft.

Alternative powertrain strategies and fleet turnover in the 21st century.

Science.gov (United States)

2010-08-01

The changes taking place in the global automotive industry related to alternative : powertrains and fuels are affecting each country or region differently. Each country or : region has its own policies in place to monitor and manage vehicle fuel cons...

Multiple target sound quality balance for hybrid electric powertrain noise

Science.gov (United States)

Mosquera-Sánchez, J. A.; Sarrazin, M.; Janssens, K.; de Oliveira, L. P. R.; Desmet, W.

2018-01-01

The integration of the electric motor to the powertrain in hybrid electric vehicles (HEVs) presents acoustic stimuli that elicit new perceptions. The large number of spectral components, as well as the wider bandwidth of this sort of noises, pose new challenges to current noise, vibration and harshness (NVH) approaches. This paper presents a framework for enhancing the sound quality (SQ) of the hybrid electric powertrain noise perceived inside the passenger compartment. Compared with current active sound quality control (ASQC) schemes, where the SQ improvement is just an effect of the control actions, the proposed technique features an optimization stage, which enables the NVH specialist to actively implement the amplitude balance of the tones that better fits into the auditory expectations. Since Loudness, Roughness, Sharpness and Tonality are the most relevant SQ metrics for interior HEV noise, they are used as performance metrics in the concurrent optimization analysis, which, eventually, drives the control design method. Thus, multichannel active sound profiling systems that feature cross-channel compensation schemes are guided by the multi-objective optimization stage, by means of optimal sets of amplitude gain factors that can be implemented at each single sensor location, while minimizing cross-channel effects that can either degrade the original SQ condition, or even hinder the implementation of independent SQ targets. The proposed framework is verified experimentally, with realistic stationary hybrid electric powertrain noise, showing SQ enhancement for multiple locations within a scaled vehicle mock-up. The results show total success rates in excess of 90%, which indicate that the proposed method is promising, not only for the improvement of the SQ of HEV noise, but also for a variety of periodic disturbances with similar features.

The CO{sub 2} challenge. Aggressive downsizing for HSDI diesel - engine concept definition; Herausforderung CO{sub 2}. Aggessives Downsizing fuer HSDI-Diesel - Motorkonzeptdefinition

Energy Technology Data Exchange (ETDEWEB)

Sorger, Helfried; Howlett, Michael; Schnider, Wolfgang; Ausserhoffer, Norbert; Bartsch, Peter; Weissbaeck, Michael [AVL List GmbH, Graz (Austria); Soustelle, Olivier [Le Moteur Moderne, Palaiseau (France); Ragot, Patrick; Mallet, Philippe [Renault S.A.S., Rueil Malmaison (France)

2010-07-01

Against a background of consumer demand for low fuel consumption vehicles, as well as legislative pressure to reduce CO{sub 2} emissions, the automotive industry is currently developing solutions to significantly improve the efficiency of ICE-based powertrains. One answer to this challenge is the engine downsizing approach. A clear trend can be observed on the market already today: engines of 2.0L swept volume are replaced by engines with a size of about 1.6L. This paper describes the concept for an even more extreme downsizing approach for the next generation of powertrains by further reducing the engine size to 1.0L using a 3 cylinder concept with a specific power rating of 80 kW/L. AVL and Renault worked closely together to define a suitable diesel hybrid powertrain concept for EU6 emission limits. The consequences for the base engine design of such an aggressive downsizing approach were established by means of a design study supported by simulation. Key criteria for such a powertrain are to satisfy customer expectations for performance and driveability, as well as keep the NVH behaviour of the selected 3 cylinder engine configuration close to that of the traditional 4 cylinder engine reference base. The structural concept of this high power engine is based on a peak firing pressure limit of 190 bar. 2- and 4-valve per cylinder concepts are evaluated with regard to their effects on performance, emissions, fuel consumption and cost. The combustion- and EGR-system is defined with respect to EU6 emission compliance, taking into consideration DPF and NOx aftertreatment technologies. (orig.)

Modular, scalable EV powertrains for mobile energy storage

Energy Technology Data Exchange (ETDEWEB)

Christie, L. [Rapid Electric Vehicles Technologies, Vancouver, BC (Canada)

2010-07-01

Rapid Electric Vehicles (REV) develops powertrains and control systems for 100 percent electric bi-directional charging ancillary power vehicles (APVs). APV fleet vehicles are used for the purpose of mobile energy storage and are necessary for scaling energy and power according to customer demand. REV is currently using OEM frames and bodies. This presentation discussed REV's OEM strategy and its progression towards advanced APVs. The product development timeline for front wheel drive systems was also presented. Several products were also discussed, including a modular all-electric front wheel drive; an ACX2.0 to Burlington Hydro; testing of ACX2.5 systems, vehicles near completion; and a V2x demonstration. The presentation discussed each of these products in detail. Other topics that were presented included modular solutions; strategic partnerships; electric vehicle performance and requirements; and an ACX-3 drive system study. tabs., figs.

Design of a 200kW electric powertrain for a high performance electric vehicle

Directory of Open Access Journals (Sweden)

Wilmar Martinez

2016-09-01

Full Text Available With the purpose of designing the electric powertrain of a high performance electric vehicle capable of running a quarter mile in 10 seconds, firstly it is necessary to calculate the required energy, torque, and power in order to size and select the suitable storage components and electric motors. Secondly, an assessment of the powertrain arrangement is needed to choose the best internal configuration of the vehicle and guarantee the highest efficiency possible. Finally, a design of the power conversion stages, specifically the DC-DC converter that interfaces the storage unit with the electric motors, is required as well. This paper shows the energy calculation procedure based on a longitudinal dynamic model of the vehicle and the selection method of the storage components and motors needed for this application, as well as the design of two 100kW interleaved boost converters with coupled inductors. In addition, a novel operation of the interleaved boost converter is proposed in order to increase the efficiency of the converter. As a result, the designed converter achieved a power density of 24,2kW/kg with an efficiency of 98 %, which was validated by experimental tests of a low power prototype.

Powertrain definitions for Opel's brand sound considering the vehicle portfolio; Gestaltung des Powertrains fuer den Opel-Brand-Sound unter Beruecksichtigung der unterschiedlichen Positionierung der Fahrzeugpalette

Energy Technology Data Exchange (ETDEWEB)

Bernhard, U.; Herrmann, G.; Schmidt, G.O. [Adam Opel AG, Ruesselsheim (Germany)

2002-07-01

The change of value orientation in Western Europe lead to an increase of emotions buying a car. In addition to classic factors like design, today the carmakers use elements of emotion like brand sound to inspire the customers. On the one hand the job of the acoustic engineers is to meet the acoustic expectations depending on driving conditions. On the other hand there are to develop both combining elements over the whole portfolio and elements which allow a defined position of a carline-powertrain combination in the market. (orig.) [German] Im Zuge der Wandlung der westlichen Gesellschaften spielen Emotionen beim Kauf eines Automobils eine immer staerkere Rolle. Zur Unterstuetzung klassischer Mittel wie dem Design werden heute weitere emotionalisierende Elemente zur Begeisterung der Kunden eingesetzt, unter anderem auch das Klangbild eines Fahrzeugs. Dabei liegt die Aufgabe einerseits darin, der unterschiedlichen Erwartungshaltung in Abhaengigkeit vom Fahrzustand des Fahrzeugs gerecht zu werden. Andererseits die Gestaltung des Klangbildes so durchzufuehren, dass innerhalb des Portfolios sowohl verbindende Elemente als markentypisch zu finden sind als auch der Marktpositionierung gerecht werdende Elemente der einzelnen Fahrzeugtypen zu generieren. (orig.)

Efficiency improvement for vehicle powertrains using energy integration techniques

OpenAIRE

Dimitrova, Zlatina; Maréchal, François

2016-01-01

The main design criteria for the modern sustainable development of vehicle powertrains are the high energy efficiency of the conversion system, the competitive cost and the lowest possible environmental impacts. The need for efficiency improvement of the vehicle energy system induces the search for an innovative methodology during the design process. In this article the energy services for mobility and comfort are integrated. The energy integration of the mobility and the comfort service is a...

Vehicle lightweighting vs. electrification: Life cycle energy and GHG emissions results for diverse powertrain vehicles

International Nuclear Information System (INIS)

Lewis, Anne Marie; Kelly, Jarod C.; Keoleian, Gregory A.

2014-01-01

Highlights: • We modeled life cycle energy and greenhouse gas (GHG) emissions from diverse powertrain vehicles. • Lightweight versions of the vehicle models were compared against baseline models. • Maximum energy and GHG emissions occur with aluminum vs. advanced high strength steel. • Design harmonization method shows 0.2–0.3 kg of support required per 1 kg powertrain mass increase. - Abstract: This work assesses the potential of electrified vehicles and mass reduction to reduce life cycle energy and greenhouse gas (GHG) emissions. Life cycle assessment (LCA) is used to account for processes upstream and downstream of the vehicle operation, thereby incorporating regional variation of energy and GHG emissions due to electricity production and distinct energy and GHG emissions due to conventional and lightweight materials. Design harmonization methods developed in previous work are applied to create baseline and lightweight vehicle models of an internal combustion vehicle (ICV), hybrid electric vehicle (HEV) and plug-in hybrid electric vehicle (PHEV). Thus, each vehicle is designed to be functionally equivalent and incorporate the structural support required for heavier powertrains. Lightweight vehicles are designed using body-in-white (BIW) mass reduction scenarios with aluminum and advanced/high strength steel (A/HSS). For the mass reduction scenarios considered in this work, results indicate that the greatest life cycle energy and GHG emissions reductions occur when steel is replaced by aluminum. However, since A/HSS requires less energy to produce as compared to aluminum, the energy and GHG reductions per unit mass removed is greatest for A/HSS. Results of the design harmonization modeling method show that 0.2–0.3 kg of structural support is required per unit increase in powertrain mass, thus extending previous methods

An Integrated Optimal Energy Management/Gear-Shifting Strategy for an Electric Continuously Variable Transmission Hybrid Powertrain Using Bacterial Foraging Algorithm

Directory of Open Access Journals (Sweden)

Syuan-Yi Chen

2016-01-01

Full Text Available This study developed an integrated energy management/gear-shifting strategy by using a bacterial foraging algorithm (BFA in an engine/motor hybrid powertrain with electric continuously variable transmission. A control-oriented vehicle model was constructed on the Matlab/Simulink platform for further integration with developed control strategies. A baseline control strategy with four modes was developed for comparison with the proposed BFA. The BFA was used with five bacterial populations to search for the optimal gear ratio and power-split ratio for minimizing the cost: the equivalent fuel consumption. Three main procedures were followed: chemotaxis, reproduction, and elimination-dispersal. After the vehicle model was integrated with the vehicle control unit with the BFA, two driving patterns, the New European Driving Cycle and the Federal Test Procedure, were used to evaluate the energy consumption improvement and equivalent fuel consumption compared with the baseline. The results show that [18.35%,21.77%] and [8.76%,13.81%] were improved for the optimal energy management and integrated optimization at the first and second driving cycles, respectively. Real-time platform designs and vehicle integration for a dynamometer test will be investigated in the future.

Predictive Model Based Battery Constraints for Electric Motor Control within EV Powertrains

NARCIS (Netherlands)

Roşca, B.; Wilkins, S.; Jacob, J.; Hoedemaekers, E.R.G.; Hoek, S.P. van den

2014-01-01

This paper presents a method of predicting the maximum power capability of a Li-Ion battery, to be used for electric motor control within automotive powertrains. As maximum power is highly dependent on battery state, the method consists of a pack level state observer coupled with a predictive

Powertrain sizing of electrically supercharged internal combustion engine vehicles

NARCIS (Netherlands)

Murgovski, N.; Marinkov, S.; Hilgersom, D.; de Jager, B.; Steinbuch, M.; Sjöberg, J.

2015-01-01

We assess the concept of electrically supercharged internal combustion engines, where the supercharger, consisting of a compressor and an electric motor, draws electric power from a buffer (a battery or a supercapacitor). In particular, we investigate the scenario of downsizing the engine, while

Investigation of a Novel Coaxial Power-Split Hybrid Powertrain for Mining Trucks

Directory of Open Access Journals (Sweden)

Weiwei Yang

2018-01-01

Full Text Available Due to the different working conditions and specification requirements of mining trucks when compared to commercial passenger vehicles, better fuel efficiency of mining trucks could lead to more significant economic benefits. Therefore, investigating a hybrid transmission system becomes essential. A coaxial power-split hybrid powertrain system for mining trucks is presented in this paper. The system is characterized as comprising an engine, a generator (MG1, a motor (MC2, two sets of planetary gears, and a clutch (CL1. There are six primary operation modes for the hybrid system including the electric motor mode, the engine mode, the hybrid electric mode, the hybrid and assist mode, the regenerative mode, and the stationary charging mode. The mathematical model of the coaxial power-split hybrid system is established according to the requirements of vehicle dynamic performance and fuel economy performance in a given driving cycle. A hybrid vehicle model based on a rule-based control strategy is established to evaluate the fuel economy. Compared with the Toyota Hybrid System (THS and the conventional mechanical vehicle system using a diesel engine, the simulation results based on an enterprise project indicate that the proposed hybrid system can enhance the vehicle’s fuel economy by 8.21% and 22.45%, respectively, during the given mining driving cycle. The simulation results can be used as a reference to study the feasibility of the proposed coaxial hybrid system whose full potential needs to be further investigated by adopting non-causal control strategies.

The electric powertrain of the R8 e-tron. A sportive experience of electromobility; Der elektrische Antrieb im R8 e-tron. Elektromobilitaet sportlich erfahren

Energy Technology Data Exchange (ETDEWEB)

Eiser, A.; Enzinger, M.; Werner, M.; Wierl, U.; Kruse, A.; Westermaier, C.; Felkel, T. [Audi AG, Ingolstadt (Germany)

2012-11-01

This article presents the electric powertrain for the new Audi R8 e-tron. The special feature of this sports car is its high-performance electric powertrain, providing a fully usable stand-alone vehicle propulsion system. At the heart of the system are two permanent-magnet synchronous motors which drive the left and right rear wheels separately. The motors were developed specially for use in the R8 e-tron to feature maximum power density, sporty performance and optimum power utilisation. Based on the latest Audi networking technologies, Flex-Ray communication has been extended to the drive components. The application and balancing of vehicle characteristics, functional reliability and drive-ability was tested in parallel on the real vehicle from the very beginning, which meant that the development was completed in an outstandingly short time. (orig.)

Description of broadband structure-borne and airborne noise transmission from the powertrain (engine-gear combination including engine intake and exhaust system) in modern combustion process as well as new systems for variable control of gas exchange. Binaural transfer path analysis and synthesis. Interim report; Beschreibung der breitbandigen Koerper- und Luftschallausbreitung aus dem Powertrain (Motor-Getriebe-Verband inklusive Ansaug- und Abgasanlage) bei modernen Verbrennungsverfahren sowie neuer Systeme zur variablen Ladungswechselsteuerung. Binaurale Transferpfadanalyse und -synthese. Zwischenbericht

Energy Technology Data Exchange (ETDEWEB)

Sottek, R. [HEAD acoustics GmbH, Herzogenrath (Germany); Behler, G.; Kellert, T. [RWTH Aachen (DE). Inst. fuer Technische Akustik (ITA); Bernhard, U.

2004-07-01

The modern combustion procedures and new valve train generations lead to a different temporal and spectral behaviour of the vibrations between the interfaces of a powertrain and the adjoining structures and at the same time to a different airborne sound radiation via the engine compartment and the orifices and component surfaces at the intake and exhaust system into the passenger compartment. The influence of the high-frequency components on the vehicle interior noise becomes more and more important. Coupling and mass effects have to be taken into consideration now, because otherwise results might increasingly be misinterpreted. Previous methods including the binaural transfer path analysis and synthesis do not take account of these effects. This research project shall fill this gap. Regarding the airborne sound component the engine compartment can at best be considered as a pressure chamber for low frequencies only. However, for higher frequencies the positions of the partial sound sources, the corresponding transfer functions, near-field effects and modal structures in the engine compartment become increasingly relevant. In this project these influencing parameters shall be classified with regard to quality and quantity. This knowledge is also of fundamental interest for the determination of the primary sound sources on the test bench and the transferability of the results to the vehicle. The most important aim of this project is to develop simplified models for the structure-borne and airborne noise transmission from a precise and complex database and to reduce them to the essential by means of parameter studies. In the final stage of the project, the complicated fine structures of the transfer functions will be reduced to a few model functions, similar to the procedure of the modal analysis. From this simple model a ''black box'' will be derived which is the basis for simulating driving conditions, applying modifications and judging them

Optimal Control of Diesel Engines with Waste Heat Recovery System

NARCIS (Netherlands)

Willems, F.P.T.; Donkers, M.C.F.; Kupper, F.

2014-01-01

This study presents an integrated energy and emission management strategy for a Euro-VI diesel engine with Waste Heat Recovery (WHR) system. This Integrated Powertrain Control (IPC) strategy optimizes the CO2-NOx trade-off by minimizing the operational costs associated with fuel and AdBlue

Optimal control of diesel engines with waste heat recovery systems

NARCIS (Netherlands)

Willems, F.P.T.; Donkers, M.C.F.; Kupper, F.; Waschl, H.; Kolmanovsky, I.; Steinbuch, M.; Del Re, L.

2014-01-01

This study presents an integrated energy and emission management strategy for a Euro-VI diesel engine with Waste Heat Recovery (WHR) system. This Integrated Powertrain Control (IPC) strategy optimizes the CO 2 - NO x trade-off by minimizing the operational costs associated with fuel and AdBlue

Energy efficiency analysis: biomass-to-wheel efficiency related with biofuels production, fuel distribution, and powertrain systems.

Directory of Open Access Journals (Sweden)

Wei-Dong Huang

Full Text Available BACKGROUND: Energy efficiency analysis for different biomass-utilization scenarios would help make more informed decisions for developing future biomass-based transportation systems. Diverse biofuels produced from biomass include cellulosic ethanol, butanol, fatty acid ethyl esters, methane, hydrogen, methanol, dimethyether, Fischer-Tropsch diesel, and bioelectricity; the respective powertrain systems include internal combustion engine (ICE vehicles, hybrid electric vehicles based on gasoline or diesel ICEs, hydrogen fuel cell vehicles, sugar fuel cell vehicles (SFCV, and battery electric vehicles (BEV. METHODOLOGY/PRINCIPAL FINDINGS: We conducted a simple, straightforward, and transparent biomass-to-wheel (BTW analysis including three separate conversion elements--biomass-to-fuel conversion, fuel transport and distribution, and respective powertrain systems. BTW efficiency is a ratio of the kinetic energy of an automobile's wheels to the chemical energy of delivered biomass just before entering biorefineries. Up to 13 scenarios were analyzed and compared to a base line case--corn ethanol/ICE. This analysis suggests that BEV, whose electricity is generated from stationary fuel cells, and SFCV, based on a hydrogen fuel cell vehicle with an on-board sugar-to-hydrogen bioreformer, would have the highest BTW efficiencies, nearly four times that of ethanol-ICE. SIGNIFICANCE: In the long term, a small fraction of the annual US biomass (e.g., 7.1%, or 700 million tons of biomass would be sufficient to meet 100% of light-duty passenger vehicle fuel needs (i.e., 150 billion gallons of gasoline/ethanol per year, through up to four-fold enhanced BTW efficiencies by using SFCV or BEV. SFCV would have several advantages over BEV: much higher energy storage densities, faster refilling rates, better safety, and less environmental burdens.

Energy Efficiency Analysis: Biomass-to-Wheel Efficiency Related with Biofuels Production, Fuel Distribution, and Powertrain Systems

Science.gov (United States)

Huang, Wei-Dong; Zhang, Y-H Percival

2011-01-01

Background Energy efficiency analysis for different biomass-utilization scenarios would help make more informed decisions for developing future biomass-based transportation systems. Diverse biofuels produced from biomass include cellulosic ethanol, butanol, fatty acid ethyl esters, methane, hydrogen, methanol, dimethyether, Fischer-Tropsch diesel, and bioelectricity; the respective powertrain systems include internal combustion engine (ICE) vehicles, hybrid electric vehicles based on gasoline or diesel ICEs, hydrogen fuel cell vehicles, sugar fuel cell vehicles (SFCV), and battery electric vehicles (BEV). Methodology/Principal Findings We conducted a simple, straightforward, and transparent biomass-to-wheel (BTW) analysis including three separate conversion elements -- biomass-to-fuel conversion, fuel transport and distribution, and respective powertrain systems. BTW efficiency is a ratio of the kinetic energy of an automobile's wheels to the chemical energy of delivered biomass just before entering biorefineries. Up to 13 scenarios were analyzed and compared to a base line case – corn ethanol/ICE. This analysis suggests that BEV, whose electricity is generated from stationary fuel cells, and SFCV, based on a hydrogen fuel cell vehicle with an on-board sugar-to-hydrogen bioreformer, would have the highest BTW efficiencies, nearly four times that of ethanol-ICE. Significance In the long term, a small fraction of the annual US biomass (e.g., 7.1%, or 700 million tons of biomass) would be sufficient to meet 100% of light-duty passenger vehicle fuel needs (i.e., 150 billion gallons of gasoline/ethanol per year), through up to four-fold enhanced BTW efficiencies by using SFCV or BEV. SFCV would have several advantages over BEV: much higher energy storage densities, faster refilling rates, better safety, and less environmental burdens. PMID:21765941

Energy efficiency analysis: biomass-to-wheel efficiency related with biofuels production, fuel distribution, and powertrain systems.

Science.gov (United States)

Huang, Wei-Dong; Zhang, Y-H Percival

2011-01-01

Energy efficiency analysis for different biomass-utilization scenarios would help make more informed decisions for developing future biomass-based transportation systems. Diverse biofuels produced from biomass include cellulosic ethanol, butanol, fatty acid ethyl esters, methane, hydrogen, methanol, dimethyether, Fischer-Tropsch diesel, and bioelectricity; the respective powertrain systems include internal combustion engine (ICE) vehicles, hybrid electric vehicles based on gasoline or diesel ICEs, hydrogen fuel cell vehicles, sugar fuel cell vehicles (SFCV), and battery electric vehicles (BEV). We conducted a simple, straightforward, and transparent biomass-to-wheel (BTW) analysis including three separate conversion elements--biomass-to-fuel conversion, fuel transport and distribution, and respective powertrain systems. BTW efficiency is a ratio of the kinetic energy of an automobile's wheels to the chemical energy of delivered biomass just before entering biorefineries. Up to 13 scenarios were analyzed and compared to a base line case--corn ethanol/ICE. This analysis suggests that BEV, whose electricity is generated from stationary fuel cells, and SFCV, based on a hydrogen fuel cell vehicle with an on-board sugar-to-hydrogen bioreformer, would have the highest BTW efficiencies, nearly four times that of ethanol-ICE. In the long term, a small fraction of the annual US biomass (e.g., 7.1%, or 700 million tons of biomass) would be sufficient to meet 100% of light-duty passenger vehicle fuel needs (i.e., 150 billion gallons of gasoline/ethanol per year), through up to four-fold enhanced BTW efficiencies by using SFCV or BEV. SFCV would have several advantages over BEV: much higher energy storage densities, faster refilling rates, better safety, and less environmental burdens.

Generation of rotary vibrations in internal combustion engines with elastically coupled electric power systems; Erzeugung von verbrennungsmotorischen Drehschwingungen mit elastisch gekoppelten elektrischen Antrieben

Energy Technology Data Exchange (ETDEWEB)

Falkenstein, Jens Werner [Rostock Univ. (Germany). Inst. fuer Antriebstechnik und Mechatronik

2004-07-01

The design of motor car powertrains requires simulations as well as prototype tests. For the simulations, prototype parameters must be identified on test rigs, simulation results must be verified, and life tests must be carried out. This necessitates realistic and reproducible excitation of vibrations. Thee book describes the development and construction of a test rig which, with the aid of electric power systems, induces rotary vibrations like those which may occur in internal combustion engines due to gas forces and unbalanced mass forces. In combination with excess resonance, the test stand achieves high dynamics with average rotary momenta up to 600 Nm. The development process is documented, from test stand design with specially developed servo-engines to the control hardware to modelling, control element design, and commissioning. (orig.)

Coordinated powertrain control for automatic transmission systems - a contribution to making driving easier and reducing environmental pollution; Koordinierte Antriebsstrangsteuerung fuer automatische Getriebe - ein Beitrag zur Entlastung von Fahrer und Umwelt

Energy Technology Data Exchange (ETDEWEB)

Huelser, H.; Loeffler, J. [Robert Bosch GmbH, Stuttgart (Germany); Mies, M. [Adam Opel AG, Ruesselsheim (Germany)

1999-07-01

The contribution presents a coordinated powertrain control system for vehicles with automatic transmission. The control system is universally applicable with different types of engines and transmission systems. It works by selecting gears and engine torque according to the position of the driving pedal and thus optimizes fuel consumption, vehicle dynamics and emissions. The powertrain control system is integrated in the CARTRONIC system architecture which ensures simple, coordinated handling of all control systems of the vehicle. Together with a board network management system, it can be integrated into an overall system for optimisation of mechanical and electrical energy use in the vehicle. [German] Der Beitrag stellt eine Koordinierte Antriebsstrangsteuerung fuer Fahrzeuge mit automatischen Getrieben vor, die einen Verbrennungsmotor mit elektronischer Motorleistungssteuerung, eine automatisierte mechanische Kupplung bzw. eine Wandlerueberbrueckungskupplung, sowie das Getriebe steuert. Diese Steuerung ist fuer unterschiedliche Typen von Motoren und Getrieben universell einsetzbar. Die Antriebsstrangsteuerung interpretiert die Fahrpedalstellung als Fahrerwunsch nach einer Vortriebsleistung und setzt diese durch geeignete Auswahl von Gang und Motordrehmoment um. Durch eine Adaption der Gangauswahl an den Fahrertyp, die Fahrsituation und Umgebungsbedingungen wird ein optimaler Fahrzeugbetrieb hinsichtlich Kraftstoffverbrauch, dynamischem Fahrverhalten und Emissionen erreicht. Die Koordinierte Antriebsstrangsteuerung ist integriert in die CARTRONIC-Systemarchitektur, die den fahrzeugweiten Verbund der Steuerungs- und Regelungssysteme einfach handhabbar macht. So kann sie gemeinsam mit einem Bordnetz-Management in ein fahrzeugweites System zur Gesamt-Optimierung von mechanischer und elektrischer Energie integriert werden. (orig.)

Liquid Rocket Engine Testing

Science.gov (United States)

2016-10-21

Briefing Charts 3. DATES COVERED (From - To) 17 October 2016 – 26 October 2016 4. TITLE AND SUBTITLE Liquid Rocket Engine Testing 5a. CONTRACT NUMBER...298 (Rev. 8-98) Prescribed by ANSI Std. 239.18 Liquid Rocket Engine Testing SFTE Symposium 21 October 2016 Jake Robertson, Capt USAF AFRL...Distribution Unlimited. PA Clearance 16493 Liquid Rocket Engine Testing • Engines and their components are extensively static-tested in development • This

The BMW Z8. Pt. 2. Engine, powertrain, chassis, acoustics, quality and repair procedures; Der BMW Z8. T. 2. Motor, Antrieb, Fahrwerk, Akustik, Qualitaetsmanagement, Reparaturverfahren

Energy Technology Data Exchange (ETDEWEB)

Dietrich, C. [Bayerische Motoren Werke AG (BMW), Muenchen (Germany)

2000-08-01

As the new kid on the block among the super sports cars, the Z8 is aimed at a small group of discerning customers who have the highest demands and wish to combine 'the ultimate driving machine and the ultimate design with exclusivity, safety, relability and quality'. The very latest in engineering, such as the aluminium structure and aluminium exterior skin, the high peformance powertrain and the sophisticated sports chassis, the stability control system, the high-performance braking system and the tyres with emergency 'Run-Flat' features go together make the Z8 an extraordinary sports car. A full range of equipment with a hardtop, telephone, audio and navigation system, attention to detail and lots of aluminium in the interior combined with high quality leather underline the exclusivity of the Z8. (orig.) [German] Als Neuling im Kreis der Supersportwagen ist der Z8 fuer einen kleinen Kreis von Kunden bestimmt, die hoechste Ansprueche stellen, die 'Freude am Fahren, Freude an der Form mit Exklusivitaet, Sicherheit, Zuverlaessigkeit und Qualitaet' verbinden wollen. Modernste Technik wie die Aluminiumstruktur und Aluminiumaussenhaut, das Hochleistungstriebwerk in Verbindung mit dem aufwendigen Sportfahrwerk, den Stabilitaetsregelsystemen, der Hochleistungsbremsanlage und den Reifen mit Notlaufeigenschaften machen den Z8 zu einem aussergewoehnlichen Sportwagen. (orig.)

Optimization of gear ratio and power distribution for a multimotor powertrain of an electric vehicle

Science.gov (United States)

Urbina Coronado, Pedro Daniel; Orta Castañón, Pedro; Ahuett-Garza, Horacio

2018-02-01

The architecture and design of the propulsion system of electric vehicles are highly important for the reduction of energy losses. This work presents a powertrain composed of four electric motors in which each motor is connected with a different gear ratio to the differential of the rear axle. A strategy to reduce energy losses is proposed, in which two phases are applied. Phase 1 uses a divide-and-conquer approach to increase the overall output efficiency by obtaining the optimal torque distribution for the electric motors. Phase 2 applies a genetic algorithm to find the optimal value of the gear ratios, in which each individual of each generation applies Phase 1. The results show an optimized efficiency map for the output torque and speed of the powertrain. The increase in efficiency and the reduction of energy losses are validated by the use of numerical experiments in various driving cycles.

Virtual Turbine Engine Test Bench Using MGET Test Device

Science.gov (United States)

Kho, Seonghee; Kong, Changduk; Ki, Jayoung

2015-05-01

Test device using virtual engine simulator can help reduce the number of engine tests through tests similar to the actual engine tests and repeat the test under the same condition, and thus reduce the engine maintenance and operating costs [1]. Also, as it is possible to easily implement extreme conditions in which it is hard to conduct actual tests, it can prevent engine damages that may happen during the actual engine test under such conditions. In this study, an upgraded MGET test device was developed that can conduct both real and virtual engine test by applying real-time engine model to the existing MGET test device that was developed and has been sold by the Company. This newly developed multi-purpose MGET test device is expected to be used for various educational and research purposes.

Solar-Thermal Engine Testing

Science.gov (United States)

Tucker, Stephen; Salvail, Pat; Haynes, Davy (Technical Monitor)

2001-01-01

A solar-thermal engine serves as a high-temperature solar-radiation absorber, heat exchanger, and rocket nozzle. collecting concentrated solar radiation into an absorber cavity and transferring this energy to a propellant as heat. Propellant gas can be heated to temperatures approaching 4,500 F and expanded in a rocket nozzle, creating low thrust with a high specific impulse (I(sub sp)). The Shooting Star Experiment (SSE) solar-thermal engine is made of 100 percent chemical vapor deposited (CVD) rhenium. The engine 'module' consists of an engine assembly, propellant feedline, engine support structure, thermal insulation, and instrumentation. Engine thermal performance tests consist of a series of high-temperature thermal cycles intended to characterize the propulsive performance of the engines and the thermal effectiveness of the engine support structure and insulation system. A silicone-carbide electrical resistance heater, placed inside the inner shell, substitutes for solar radiation and heats the engine. Although the preferred propellant is hydrogen, the propellant used in these tests is gaseous nitrogen. Because rhenium oxidizes at elevated temperatures, the tests are performed in a vacuum chamber. Test data will include transient and steady state temperatures on selected engine surfaces, propellant pressures and flow rates, and engine thrust levels. The engine propellant-feed system is designed to Supply GN2 to the engine at a constant inlet pressure of 60 psia, producing a near-constant thrust of 1.0 lb. Gaseous hydrogen will be used in subsequent tests. The propellant flow rate decreases with increasing propellant temperature, while maintaining constant thrust, increasing engine I(sub sp). In conjunction with analytical models of the heat exchanger, the temperature data will provide insight into the effectiveness of the insulation system, the structural support system, and the overall engine performance. These tests also provide experience on operational

Optimization of a fuel cell powertrain for a sport utility vehicle. Paper no. IGEC-1-087

International Nuclear Information System (INIS)

Stevens, M.B.; Mendes, C.; Mali, T.J.; Fowler, M.W.; Fraser, R.A.

2005-01-01

A central composite design was utilized to study the effects of fuel cell powertrain sizing and efficiencies on vehicle performance based on a Chevrolet Equinox platform. Simulations were performed using the Powertrain System Analysis Toolkit (PSAT), a vehicle simulator that constructs and executes various Simulink vehicle models. Once parametric equations relating performance metrics and subcomponent sizing and efficiency were fit, optimal design points were obtained using non-linear optimization. Optimized architectures were used to compare fuel cell powertrains incorporating ultracapacitors, nickel-metal hydride battery packs, and lithium-ion battery packs. The performance metrics also provided a basis for comparison with conventional, battery, and hybrid configurations. The fuel cell configurations exhibited similar or improved acceleration performance, with approximately double the mileage of the stock vehicle. The range of the fuel cell Equinox was reduced from the stock vehicle to approximately 300 miles. The battery vehicles showed the highest efficiencies and mileages, but exhibited an unacceptable range of approximately 100 miles. The hybrid configuration showed notable improvements over the stock vehicle, but still lacked the degree of benefits provided by the fuel cell (FCVs) and battery electric vehicles (BEVs). Also, the acceleration time for the hybrid vehicle was sluggish, likely due to the increase weight of the configuration. The work described in this study was performed by members of the University Of Waterloo Alternate Fuels Team (UWAFT) as part of the Challenge X Vehicle Competition. (author)

Engine Test Facility (ETF)

Data.gov (United States)

Federal Laboratory Consortium — The Air Force Arnold Engineering Development Center's Engine Test Facility (ETF) test cells are used for development and evaluation testing of propulsion systems for...

Integrated Energy & Emission Management for Heavy-Duty Diesel Engines with Waste Heat Recovery System

NARCIS (Netherlands)

Willems, F.P.T.; Kupper, F.; Cloudt, R.P.M.

2012-01-01

This study presents an integrated energy and emission management strategy for an Euro-VI diesel engine with Waste Heat Recovery (WHR) system. This Integrated Powertrain Control (IPC) strategy optimizes the CO2-NOx trade-off by minimizing the operational costs associated with fuel and AdBlue

7th Conference Simulation and Testing for Vehicle Technology

CERN Document Server

Riese, Jens; Rüden, Klaus

2016-01-01

The book includes contributions on the latest model-based methods for the development of personal and commercial vehicle control devices. The main topics treated are: application of simulation and model design to development of driver assistance systems; physical and database model design for engines, motors, powertrain, undercarriage and the whole vehicle; new simulation tools, methods and optimization processes; applications of simulation in function and software development; function and software testing using HiL, MiL and SiL simulation; application of simulation and optimization in application of control devices; automation approaches at all stages of the development process.

Liquid Rocket Engine Testing Overview

Science.gov (United States)

Rahman, Shamim

2005-01-01

Contents include the following: Objectives and motivation for testing. Technology, Research and Development Test and Evaluation (RDT&E), evolutionary. Representative Liquid Rocket Engine (LRE) test compaigns. Apollo, shuttle, Expandable Launch Vehicles (ELV) propulsion. Overview of test facilities for liquid rocket engines. Boost, upper stage (sea-level and altitude). Statistics (historical) of Liquid Rocket Engine Testing. LOX/LH, LOX/RP, other development. Test project enablers: engineering tools, operations, processes, infrastructure.

SILHIL Replication of Electric Aircraft Powertrain Dynamics and Inner-Loop Control for V&V of System Health Management Routines

Science.gov (United States)

Bole, Brian; Teubert, Christopher Allen; Cuong Chi, Quach; Hogge, Edward; Vazquez, Sixto; Goebel, Kai; George, Vachtsevanos

2013-01-01

Software-in-the-loop and Hardware-in-the-loop testing of failure prognostics and decision making tools for aircraft systems will facilitate more comprehensive and cost-effective testing than what is practical to conduct with flight tests. A framework is described for the offline recreation of dynamic loads on simulated or physical aircraft powertrain components based on a real-time simulation of airframe dynamics running on a flight simulator, an inner-loop flight control policy executed by either an autopilot routine or a human pilot, and a supervisory fault management control policy. The creation of an offline framework for verifying and validating supervisory failure prognostics and decision making routines is described for the example of battery charge depletion failure scenarios onboard a prototype electric unmanned aerial vehicle.

Integrated energy and emission management for heavy-duty diesel engines with waste heat recovery system

NARCIS (Netherlands)

Willems, F.P.T.; Kupper, F.; Cloudt, R.P.M.

2012-01-01

This study presents an integrated energy and emission management strategy for an Euro-VI diesel engine with Waste Heat Recovery (WHR) system. This Integrated Powertrain Control (IPC) strategy optimizes the CO2-NOx trade-off by minimizing the operational costs associated with fuel and AdBlue

Reverse engineering of a railcar prototype via energetic macroscopic representation approach

International Nuclear Information System (INIS)

Agbli, Kréhi Serge; Hissel, Daniel; Sorrentino, Marco; Chauvet, Frédéric; Pouget, Julien

2016-01-01

Highlights: • A complex EMR model of a new railcar range has been developed. • A satisfactory assessment of the fuel consumption of the railcar. • The significant potential benefits are attainable by hybridizing the original railcar. • The regenerative braking can provide up to 240 kW h saving. - Abstract: Energetic Macroscopic Representation (EMR) modelling approach is proposed to perform model-based reverse-engineering of a new railcar range, having six propulsion units, each consisting of a diesel engine and a traction motor. Particularly, EMR intrinsic features were exploited to perform phenomenological structuration of power flows, thus allowing proper and comprehensive modelling of complex systems, such as the under-study railcar. Based on some prospective real trips, selected in such a way as to enable realistic evaluation of effective railcar effort, EMR-based prediction of railcar energy consumption is performed. Furthermore, physical consistency of each powertrain component operation was carefully verified. The suitability of EMR approach was thus proven effective to perform reverse-engineering of known specifications and available experimental data, with the final aim of reconstructing a high fidelity computational tool that meets computational burden requirements for subsequent model-based tasks deployment. Finally, specific simulation analyses were performed to evaluate the potential benefits attainable through electric hybridization of the original powertrain.

Optimization to reduce fuel consumption in charge depleting mode

Science.gov (United States)

Roos, Bryan Nathaniel; Martini, Ryan D.

2014-08-26

A powertrain includes an internal combustion engine, a motor utilizing electrical energy from an energy storage device, and a plug-in connection. A Method for controlling the powertrain includes monitoring a fuel cut mode, ceasing a fuel flow to the engine based upon the fuel cut mode, and through a period of operation including acceleration of the powertrain, providing an entirety of propelling torque to the powertrain with the electrical energy from the energy storage device based upon the fuel cut mode.

Supervisory control of a heavy-duty diesel engine with an electrified waste heat recovery system

NARCIS (Netherlands)

Feru, E.; Murgovski, N.; de Jager, A.G.; Willems, F.P.T.

This paper presents an integrated energy and emission management strategy, called Integrated Powertrain Control (IPC), for an Euro-VI diesel engine with an electrified waste heat recovery system. This strategy optimizes the CO2–NOxCO2–NOx trade-off by minimizing the operational costs associated with

Integrating ergonomics into production system development--the Volvo Powertrain case.

Science.gov (United States)

Neumann, W Patrick; Ekman, Marianne; Winkel, Jørgen

2009-05-01

Understanding the barriers and assists to integrating ergonomics into production system design remains a research issue. An action research case study at Volvo Powertrain/Sweden was conducted. Researchers worked collaboratively with the firm in efforts to improve the company's ability to handle ergonomics in their daily work of improving and developing production systems. Researchers observed and reflected collectively on the change process using field notes and recordings to support their observations. Observed integration barriers included both individual level issues like life events, and organisational aspects such as communication barriers between groups or assignment of tasks to people not involved in decision-making. Observed assists included the 'political reflective navigation' (c.f. Broberg, O., Hermund, I., 2004. The OHS consultant as a 'political reflective navigator' in technological change processes. International Journal of Industrial Ergonomics 33 (4), 315-326) by the project owner to find new ways to overcome barriers and anchor ergonomics into the organisation. While special 'ergonomics' groups did not survive long, progress was observed in including ergonomics in regular design groups. A cross-functional workshop that fostered discussion across organisational boundaries helped shift focus from retrofitting systems to future production systems and improve engagement of engineering teams. Progress was marked by both success and setbacks and full integration appears to require more than 2 years time. It is concluded that support by senior managers should include succession planning for personnel that are key to the change effort.

Engineering test facility

International Nuclear Information System (INIS)

Steiner, D.; Becraft, W.R.; Sager, P.H.

1981-01-01

The vehicle by which the fusion program would move into the engineering testing phase of fusion power development is designated the Engineering Test Facility (ETF). The ETF would provide a test-bed for reactor components in the fusion environment. In order to initiate preliminary planning for the ETF decision, the Office of Fusion Energy established the ETF Design Center activity to prepare the design of the ETF. This paper described the design status of the ETF

Modeling, simulation, and concept studies of a fuel cell hybrid electric vehicle powertrain

Energy Technology Data Exchange (ETDEWEB)

Oezbek, Markus

2010-03-29

This thesis focuses on the development of a fuel cell-based hybrid electric powertrain for smaller (2 kW) hybrid electric vehicles (HEVs). A Hardware-in-the-Loop test rig is designed and built with the possibility to simulate any load profile for HEVs in a realistic environment, whereby the environment is modeled. Detailed simulation models of the test rig are developed and validated to real physical components and control algorithms are designed for the DC/DC-converters and the fuel cell system. A state-feedback controller is developed for the DC/DC-converters where the state-space averaging method is used for the development. For the fuel cells, a gain-scheduling controller based on state feedback is developed and compared to two conventional methods. The design process of an HEV with regard to a given load profile is introduced with comparison between SuperCaps and batteries. The HEV is also evaluated with an introduction to different power management concepts with regard to fuel consumption, dynamics, and fuel cell deterioration rate. The power management methods are implemented in the test rig and compared. (orig.)

Extended-Kalman-filter-based regenerative and friction blended braking control for electric vehicle equipped with axle motor considering damping and elastic properties of electric powertrain

Science.gov (United States)

Lv, Chen; Zhang, Junzhi; Li, Yutong

2014-11-01

Because of the damping and elastic properties of an electrified powertrain, the regenerative brake of an electric vehicle (EV) is very different from a conventional friction brake with respect to the system dynamics. The flexibility of an electric drivetrain would have a negative effect on the blended brake control performance. In this study, models of the powertrain system of an electric car equipped with an axle motor are developed. Based on these models, the transfer characteristics of the motor torque in the driveline and its effect on blended braking control performance are analysed. To further enhance a vehicle's brake performance and energy efficiency, blended braking control algorithms with compensation for the powertrain flexibility are proposed using an extended Kalman filter. These algorithms are simulated under normal deceleration braking. The results show that the brake performance and blended braking control accuracy of the vehicle are significantly enhanced by the newly proposed algorithms.

Powertrain management in hybrid vehicles with 48 V electrical system; Antriebsstrangmanagement in Hybridfahrzeugen mit 48-V-Bordnetz

Energy Technology Data Exchange (ETDEWEB)

Graf, Friedrich; Knorr, Thomas; Jehle, Martin; Huber, Tobias [Continental Automotive GmbH, Regensburg (Germany). Div. Powertrain

2013-09-15

Continental has developed a comprehensive system approach for powertrain management in hybrid vehicles with a 48 V power supply network. This system is based on the complete range of products and functions offered by the company, from the drive belt to the electronics and the battery. (orig.)

Wind Turbine Generator Efficiency Based on Powertrain Combination and Annual Power Generation Prediction

Directory of Open Access Journals (Sweden)

Dongmyung Kim

2018-05-01

Full Text Available Wind turbine generators are eco-friendly generators that produce electric energy using wind energy. In this study, wind turbine generator efficiency is examined using a powertrain combination and annual power generation prediction, by employing an analysis model. Performance testing was conducted in order to analyze the efficiency of a hydraulic pump and a motor, which are key components, and so as to verify the analysis model. The annual wind speed occurrence frequency for the expected installation areas was used to predict the annual power generation of the wind turbine generators. It was found that the parallel combination of the induction motors exhibited a higher efficiency when the wind speed was low and the serial combination showed higher efficiency when wind speed was high. The results of predicting the annual power generation considering the regional characteristics showed that the power generation was the highest when the hydraulic motors were designed in parallel and the induction motors were designed in series.

Space Electronic Test Engineering

Science.gov (United States)

Chambers, Rodney D.

2004-01-01

The Space Power and Propulsion Test Engineering Branch at NASA Glenn Research center has the important duty of controlling electronic test engineering services. These services include test planning and early assessment of Space projects, management and/or technical support required to safely and effectively prepare the article and facility for testing, operation of test facilities, and validation/delivery of data to customer. The Space Electronic Test Engineering Branch is assigned electronic test engineering responsibility for the GRC Space Simulation, Microgravity, Cryogenic, and Combustion Test Facilities. While working with the Space Power and Propulsion Test Engineering Branch I am working on several different assignments. My primary assignment deals with an electrical hardware unit known as Sunny Boy. Sunny Boy is a DC load Bank that is designed for solar arrays in which it is used to convert DC power form the solar arrays into AC power at 60 hertz to pump back into the electricity grid. However, there are some researchers who decided that they would like to use the Sunny Boy unit in a space simulation as a DC load bank for a space shuttle or even the International Space Station hardware. In order to do so I must create a communication link between a computer and the Sunny Boy unit so that I can preset a few of the limits (such power, set & constant voltage levels) that Sunny Boy will need to operate using the applied DC load. Apart from this assignment I am also working on a hi-tech circuit that I need to have built at a researcher s request. This is a high voltage analog to digital circuit that will be used to record data from space ion propulsion rocket booster tests. The problem that makes building this circuit so difficult is that it contains high voltage we must find a way to lower the voltage signal before the data is transferred into the computer to be read. The solution to this problem was to transport the signal using infrared light which will lower

40 CFR 90.410 - Engine test cycle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine test cycle. 90.410 Section 90... Procedures § 90.410 Engine test cycle. (a) Follow the appropriate 6-mode test cycle for Class I, I-B and II engines and 2-mode test cycle for Class I-A, III, IV, and V engines when testing spark-ignition engines...

Gasoline hybrid pneumatic engine for efficient vehicle powertrain hybridization

OpenAIRE

Dimitrova, Zlatina; Maréchal, François

2015-01-01

The largest applied convertors in passenger cars are the internal combustion engines – gasoline, diesel, adapted also for operating on alternative fuels and hybrid modes. The number of components that are necessary to realize modern future propulsion system is inexorably increasing. The need for efficiency improvement of the vehicle energy system induces the search for an innovative methodology during the design process. In this article the compressed air is investigated as an innovative solu...

Pistons and engine testing

CERN Document Server

GmbH, Mahle

2012-01-01

The ever-increasing demands placed on combustion engines are just as great when it comes to this centerpiece - the piston. Achieving less weight or friction, or even greater wear resistance, requires in-depth knowledge of the processes taking place inside the engine, suitable materials, and appropriate design and machining processes for pistons, including the necessary testing measures. It is no longer possible for professionals in automotive engineering to manage without specific know-how of this kind, whether they work in the field of design, development, testing, or maintenance. This techni

Engine process simulation and supercharging. Proceedings; Motorprozesssimulation und Aufladung. Tagungsbeitraege

Energy Technology Data Exchange (ETDEWEB)

Pucher, H.; Kahrstedt, J. (eds.)

2005-07-01

Engine process simulation has become an integral part of research and development for all types of internal combustion engines. It allows developers to obtain information on the steady-state and dynamic operating behavior of any type of internal combustion engine at early development stages without costly and laborious testing. Moreover, the entire powertrain can be included in the system under investigation. Engine process simulation is particularly important when it comes to assessing potentials and studying parameters for the development of supercharging concepts. For the investigation of existing combustion systems, however, thermodynamic analysis must be used. Furthermore, simulation nowadays is an important tool for the design and development of controllers. This documentation summarizes an exchange of knowledge and experience on the above-mentioned issues that took place during the first 'Engine Process Simulation and Supercharging' symposium held in Berlin on 30 June and 1 July 2005, i.e. the year marking 100 years of supercharging. The paper in this book report on the following subjects: (a) Use of engine process simulation in the development process. (b) Requirements placed on supercharging in conjunction with conventional and alternative combustion processes. (c) Modeling of supercharging units. (d) Combustion curve analysis as a tool to optimize combustion processes. (e) Engine control: algorithm development up to model-based approaches, sensors/actuators, hardware-in-the-loop. (orig.)

The engineering test facility

International Nuclear Information System (INIS)

Steiner, D.; Becraft, W.R.; Sager, P.H.

1981-01-01

The vehicle by which the fusion program would move into the engineering testing phase of fusion power development is designated the Engineering Test Facility (ETF). The ETF would provide a test-bed for reactor components in the fusion environment. In order to initiate preliminary planning for the ETF decision, the Office of Fusion Energy established the ETF Design Center activity to prepare the design of the ETF. This paper describes the design status of the ETF. (orig.)

Single Common Powertrain Lubricant (SCPL) Development. Part 3

Science.gov (United States)

2015-02-01

demonstrated poor spray performance and chatter when checked on a calibration bench. A new fuel transfer pump, replacement injector , and two new injector tips...results for: chemical and physical bench testing, transmission application frictional testing, high temperature 2-cycle diesel engine compatibility...industry standardized testing. However, all testing in military applications (apart from high temperature two cycle diesel engines) has shown positive

Software engineers and nuclear engineers: teaming up to do testing

International Nuclear Information System (INIS)

Kelly, D.; Cote, N.; Shepard, T.

2007-01-01

The software engineering community has traditionally paid little attention to the specific needs of engineers and scientists who develop their own software. Recently there has been increased recognition that specific software engineering techniques need to be found for this group of developers. In this case study, a software engineering group teamed with a nuclear engineering group to develop a software testing strategy. This work examines the types of testing that proved to be useful and examines what each discipline brings to the table to improve the quality of the software product. (author)

Definition study for variable cycle engine testbed engine and associated test program

Science.gov (United States)

Vdoviak, J. W.

1978-01-01

The product/study double bypass variable cycle engine (VCE) was updated to incorporate recent improvements. The effect of these improvements on mission range and noise levels was determined. This engine design was then compared with current existing high-technology core engines in order to define a subscale testbed configuration that simulated many of the critical technology features of the product/study VCE. Detailed preliminary program plans were then developed for the design, fabrication, and static test of the selected testbed engine configuration. These plans included estimated costs and schedules for the detail design, fabrication and test of the testbed engine and the definition of a test program, test plan, schedule, instrumentation, and test stand requirements.

Development and operation of a mobile test facility for education

Science.gov (United States)

Davis, Christopher T.

The automotive industry saw a large shift towards vehicle electrification after the turn of the century. It became necessary to ensure that new and existing engineers were qualified to design and calibrate these new systems. To ensure this training, Michigan Tech received a grant to develop a curriculum based around vehicle electrification. As part of this agenda, the Michigan Tech Mobile Laboratory was developed to provide hands-on training for professional engineers and technicians in hybrid electric vehicles and vehicle electrification. The Mobile Lab has since then increased the scope of the delivered curriculum to include other automotive areas and even customizable course content to meet specific needs. This thesis outlines the development of the Mobile Laboratory and its powertrain test facilities. The focus of this thesis is to discuss the different hardware and software systems within the lab and test cells. Detailed instructions on the operation and maintenance of each of the systems are discussed. In addition, this thesis outlines the setup and operation of the necessary equipment for several of the experiments for the on and off campus courses and seminars.

Simulation and material testing of jet engines

International Nuclear Information System (INIS)

Tariq, M.M.

2006-01-01

The NASA software engine simulator version U 1.7a beta has been used for simulation and material testing of jet engines. Specifications of Modem Jet Engines are stated, and then engine simulator is applied on these specifications. This simulator can simulate turbojet, afterburner, turbofan and ram jet. The material of many components of engine may be varied. Conventional and advanced materials for jet engines can be simulated and tested. These materials can be actively cooled to increase the operating temperature limit. As soon as temperature of any engine component exceeds the temperature limit of material, a warning message flashes across screen. Temperature Limits Exceeded. This flashing message remainst here until necessaryc hangesa re carried out in engine operationp rocedure. Selection Criteria of Engines is stated for piston prop, turboprop, turbofan, turbojet, and turbojet with afterburner and Ramjet. Several standard engines are modeled in Engine Simulator. These engines can. be compared by several engineering specifications. The design, modeling, simulation and testing of engines helps to better understand different types of materials used in jet engines. (author)

Liquid Rocket Engine Testing

Science.gov (United States)

Rahman, Shamim

2005-01-01

Comprehensive Liquid Rocket Engine testing is essential to risk reduction for Space Flight. Test capability represents significant national investments in expertise and infrastructure. Historical experience underpins current test capabilities. Test facilities continually seek proactive alignment with national space development goals and objectives including government and commercial sectors.

Pistons and engine testing

CERN Document Server

2016-01-01

The ever-increasing demands placed on combustion engines are just as great when it comes to this centerpiece—the piston. Achieving less weight or friction, or even greater wear resistance, requires in-depth knowledge of the processes taking place inside the engine, suitable materials, and appropriate design and manufacturing processes for pistons, including the necessary testing measures. It is no longer possible for professionals in automotive engineering to manage without specific expertise of this kind, whether they work in the field of design, development, testing, or maintenance. This technical book answers these questions in detail and in a very clear and comprehensible way. In this second, revised edition, every chapter has been revised and expanded. The chapter on “Engine testing”, for example, now include extensive results in the area of friction power loss measurement and lube oil consumption measurement. Contents Piston function, requirements, and types Design guidelines Simulation of the ope...

40 CFR 89.410 - Engine test cycle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine test cycle. 89.410 Section 89... Procedures § 89.410 Engine test cycle. (a) Emissions shall be measured using one of the test cycles specified...) through (a)(4) of this section. These cycles shall be used to test engines on a dynamometer. (1) The 8...

Small Engine & Accessory Test Area

Data.gov (United States)

Federal Laboratory Consortium — The Small Engine and Accessories Test Area (SEATA) facilitates testaircraft starting and auxiliary power systems, small engines and accessories. The SEATA consists...

Engineering test facility design center

International Nuclear Information System (INIS)

Anon.

1980-01-01

The vehicle by which the fusion program would move into the engineering testing phase of fusion power development is designated the Engineering Test Facility (ETF). The ETF would provide a test bed for reactor components in the fusion environment. In order to initiate preliminary planning for the ETF decision, the Office of Fusion Energy established the ETF Design Center activity to prepare the design of the ETF. This section describes the status of this design

40 CFR 91.410 - Engine test cycle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine test cycle. 91.410 Section 91...) CONTROL OF EMISSIONS FROM MARINE SPARK-IGNITION ENGINES Gaseous Exhaust Test Procedures § 91.410 Engine test cycle. (a) The 5-mode cycle specified in Table 2 in appendix A to this subpart shall be followed...

Alvar engine. An engine with variable compression ratio. Experiments and tests

Energy Technology Data Exchange (ETDEWEB)

Erlandsson, Olof

1998-09-01

This report is focused on tests with Variable Compression Ratio (VCR) engines, according to the Alvar engine principle. Variable compression ratio means an engine design where it is possible to change the nominal compression ratio. The purpose is to increase the fuel efficiency at part load by increasing the compression ratio. At maximum load, and maybe supercharging with for example turbocharger, it is not possible to keep a high compression ratio because of the knock phenomena. Knock is a shock wave caused by self-ignition of the fuel-air mix. If knock occurs, the engine will be exposed to a destructive load. Because of the reasons mentioned it would be an advantage if it would be possible to change the compression ratio continuously when the load changes. The Alvar engine provides a solution for variable compression ratio based on well-known engine components. This paper provides information about efficiency and emission characteristics from tests with two Alvar engines. Results from tests with a phase shift mechanism (for automatic compression ratio control) for the Alvar engine are also reviewed Examination paper. 5 refs, 23 figs, 2 tabs, 5 appendices

Powertrain preheating system of tracked hybrid electric vehicle in cold weather

International Nuclear Information System (INIS)

Wang, Rui; Wang, Yichun; Feng, Chaoqing; Zhang, Xilong

2015-01-01

In order to make sure that the heavy duty tracked vehicle can work in various conditions, especially severe cold weather, preheating system of powertrain should be adopted, and a novel preheating system is presented for the tracked hybrid electric vehicle (HEV) in which heat is generated by the low-speed drive motor. The new preheating system can meet the need of cold start without adding any additional device. The characteristic of heat generation by motor is tested when the rotor of motor is rotated in very low speed. The heat loss from power cabin to external environment has been simulated, and the relevant test has been done to verify the simulation results. Combining the characteristic of heat generation and heat loss situation about preheating system, the heat transfer model of preheating system was implemented by MATLAB. The total energy required for preheating in different ambient temperature was calculated by this model. The results showed that: the minimum heating power was 70 kW and energy required was about 180 MJ when the HEV worked in −46 °C. If lithium ferrous phosphate (LFP) battery was used in power system, the minimum battery capacity is about 290 A h. - Highlights: • A novel preheating method was proposed for heavy duty tracked HEV. • Thermal energy in preheating system is produced by the PMSM in driving system. • This method can achieve preheating target by its own components without any adding. • Analyzing low temperature performance of power battery and select its capacity.

Maintenance & Repair Cost Calculation and Assessment of Resale Value for Different Alternative Commercial Vehicle Powertrain Technologies

OpenAIRE

Kleiner, Florian; Friedrich, Horst E.

2017-01-01

For detailed evaluation of the Total Cost of Ownership, expenditures for Maintenance & Repair as well as the resale value are important to consider and should not be neglected. However, information on Maintenance & Repair costs as well as residual values for commercial vehicles with alternative powertrains is missing and data on this issue is rare. There is a lack of information and consolidated knowledge. In order to enable a holistic cost assessment for commercial vehicles, a comprehensive ...

Full Load Performance of a Spark Ignition Engine Fueled with Gasoline-Isobutanol Blends

Directory of Open Access Journals (Sweden)

Adrian Irimescu

2009-10-01

Full Text Available With fossil fuels reserves coming ever closer to depletion and the issue of air pollution caused by automotive transport becoming more and more important, mankind has looked for various solutions in the field of internal combustion engines. One of these solutions is using biofuels, and while the internal combustion engine will most likely disappear along with the last fossil fuel source, studying biofuels and their impact on automotive power-trains is a necessity even if only on a the short term basis. While engines built to run on alcohol-gasoline blends offer good performance levels even at high concentrations of alcohol, unmodified engines fueled with blends of biofuels and fossil fuels can exhibit a drop in power. The object of this study is evaluating such phenomena when a spark ignition engine is operated at full load.

The first of a new generation of diesel engines from General Motors - the efficient and powerful 1.6 liter Euro6 midsize diesel engine

Energy Technology Data Exchange (ETDEWEB)

Boretto, Gianmarco; Golisano, Roberto; Scotti, Michele; Antonioli, Pierpaolo; Frank, Richard M.; Rovatti, Giovanni [General Motors Powertrain Europe s.r.l., Turin (Italy); Wesslau, Markus [Adam Opel AG, Ruesselsheim (Germany)

2013-08-01

The major challenge the automotive industry will face in the next decade is undoubtedly the reduction of CO{sub 2} emissions. Conventional powertrains with internal combustion engines will still play a predominant role: in particular, the diesel engine will be a major contributor to the solution thanks to its intrinsic high thermodynamic efficiency and low-end torque which is a key enabler for downsizing engine displacement and downspeeding. In this context, General Motors has developed an entirely new 1.6 liter four-cylinder Midsize Diesel Engine (MDE), the first of a new generation of efficient and powerful diesel engines. Its development has been focused on the achievement of high power and torque density, superior fuel efficiency and state-of-the-art noise and vibration, while meeting the Euro6 emission standard in a wide range of B-, C- and D-segment vehicles, utilizing different exhaust aftertreatment solutions. The key technical features of the base engine, combustion system and emission reduction technologies, together with the innovative engine control unit, are described in this paper. (orig.)

Model-based power control strategy development of a fuel cell hybrid vehicle

Energy Technology Data Exchange (ETDEWEB)

Haitao, Yun [School of Automobile and Traffic, Qingdao Technological University, Qingdao Shandong 266033 (China); School of Automobile, Tongji University, ShangHai 201804 (China); Yulan, Zhao [School of Automobile and Traffic, Qingdao Technological University, Qingdao Shandong 266033 (China); Zechang, Sun; Gang, Wan [School of Automobile, Tongji University, ShangHai 201804 (China)

2008-06-01

An integrated procedure for math modeling and power control strategy design for a fuel cell hybrid vehicle (FCHV) is presented in this paper. Dynamic math model of the powertrain is constructed firstly, which includes four modules: fuel cell engine, DC/DC inverter, motor-driver, and power battery. Based on the mathematic model, a power control principle is designed, which uses full-states closed-loop feedback algorithm. To implement full-states feedback, a Luenberger state observer is designed to estimate open circuit voltage (OCV) of the battery, which make the control principle not sensitive to the battery SOC (state of charge) estimated error. Full-states feedback controller is then designed through analyzing step responding of the powertrain and test data. At last of the paper, the results of simulation and field test are illustrated. The results show that the power control strategy designed takes into account the performance and economy characteristics of components of the FCHV powertrain and achieves the control object excellently. (author)

Smart Home Hardware-in-the-Loop Testing

Energy Technology Data Exchange (ETDEWEB)

Pratt, Annabelle

2017-07-12

This presentation provides a high-level overview of NREL's smart home hardware-in-the-loop testing. It was presented at the Fourth International Workshop on Grid Simulator Testing of Energy Systems and Wind Turbine Powertrains, held April 25-26, 2017, hosted by NREL and Clemson University at the Energy Systems Integration Facility in Golden, Colorado.

Operation behaviour and vibration behaviour of the powertrain of wind power plants; Betriebs- und Schwingungsverhalten des Triebstranges von Windenergieanlagen

Energy Technology Data Exchange (ETDEWEB)

Gellermann, Thomas [AZT Risk and Technology GmbH, Muenchen (Germany)

2010-07-01

Wind power plants are exposed to high-dynamic loads by the irregular flow of the rotor. Thereby, the low-frequency oscillations of the powertrain as well as the building partly result in harmful additional loads on the components. The author of the contribution under consideration presents selected examples of the operational behaviour and vibration behaviour, and describes the exciter mechanisms.

Uprated OMS Engine Status-Sea Level Testing Results

Science.gov (United States)

Bertolino, J. D.; Boyd, W. C.

1990-01-01

The current Space Shuttle Orbital Maneuvering Engine (OME) is pressure fed, utilizing storable propellants. Performance uprating of this engine, through the use of a gas generator driven turbopump to increase operating pressure, is being pursued by the NASA Johnson Space Center (JSC). Component level design, fabrication, and test activities for this engine system have been on-going since 1984. More recently, a complete engine designated the Integrated Component Test Bed (ICTB), was tested at sea level conditions by Aerojet. A description of the test hardware and results of the sea level test program are presented. These results, which include the test condition operating envelope and projected performance at altitude conditions, confirm the capability of the selected Uprated OME (UOME) configuration to meet or exceed performance and operational requirements. Engine flexibility, demonstrated through testing at two different operational mixture ratios, along with a summary of projected Space Shuttle performance enhancements using the UOME, are discussed. Planned future activities, including ICTB tests at simulated altitude conditions, and recommendations for further engine development, are also discussed.

Integrated energy & emission management for hybrid electric truck with SCR aftertreatment

NARCIS (Netherlands)

Kessels, J.T.B.A.; Willems, F.P.T.; Schoot, W.J.; Bosch, van den P.P.J.

2010-01-01

Energy management in hybrid vehicles typicallyrelates to the vehicle powertrain, whereas emission managementis associated with the combustion engine and aftertreatmentsystem. To achieve maximum performance in fuel economy andregulated pollutants, the concept of (model-based) IntegratedPowertrain

Control system and method for a hybrid electric vehicle

Science.gov (United States)

Tamor, Michael Alan

2001-03-06

Several control methods are presented for application in a hybrid electric vehicle powertrain including in various embodiments an engine, a motor/generator, a transmission coupled at an input thereof to receive torque from the engine and the motor generator coupled to augment torque provided by the engine, an energy storage device coupled to receive energy from and provide energy to the motor/generator, an engine controller (EEC) coupled to control the engine, a transmission controller (TCM) coupled to control the transmission and a vehicle system controller (VSC) adapted to control the powertrain.

Altitude Testing of Large Liquid Propellant Engines

Science.gov (United States)

Maynard, Bryon T.; Raines, Nickey G.

2010-01-01

The National Aeronautics and Space Administration entered a new age on January 14, 2004 with President Bush s announcement of the creation the Vision for Space Exploration that will take mankind back to the Moon and on beyond to Mars. In January, 2006, after two years of hard, dedicated labor, engineers within NASA and its contractor workforce decided that the J2X rocket, based on the heritage of the Apollo J2 engine, would be the new engine for the NASA Constellation Ares upper stage vehicle. This engine and vehicle combination would provide assured access to the International Space Station to replace that role played by the Space Shuttle and additionally, would serve as the Earth Departure Stage, to push the Crew Excursion Vehicle out of Earth Orbit and head it on a path for rendezvous with the Moon. Test as you fly, fly as you test was chosen to be the guiding philosophy and a pre-requisite for the engine design, development, test and evaluation program. An exhaustive survey of national test facility assets proved the required capability to test the J2X engine at high altitude for long durations did not exist so therefore, a high altitude/near space environment testing capability would have to be developed. After several agency concepts the A3 High Altitude Testing Facility proposal was selected by the J2X engine program on March 2, 2007 and later confirmed by a broad panel of NASA senior leadership in May 2007. This facility is to be built at NASA s John C. Stennis Space Center located near Gulfport, Mississippi. 30 plus years of Space Shuttle Main Engine development and flight certification testing makes Stennis uniquely suited to support the Vision For Space Exploration Return to the Moon. Propellant handling infrastructure, engine assembly facilities, a trained and dedicated workforce and a broad and varied technical support base will all ensure that the A3 facility will be built on time to support the schedule needs of the J2X engine and the ultimate flight

History and Benefits of Engine Level Testing Throughout the Space Shuttle Main Engine Program

Science.gov (United States)

VanHooser, Katherine; Kan, Kenneth; Maddux, Lewis; Runkle, Everett

2010-01-01

Rocket engine testing is important throughout a program s life and is essential to the overall success of the program. Space Shuttle Main Engine (SSME) testing can be divided into three phases: development, certification, and operational. Development tests are conducted on the basic design and are used to develop safe start and shutdown transients and to demonstrate mainstage operation. This phase helps form the foundation of the program, demands navigation of a very steep learning curve, and yields results that shape the final engine design. Certification testing involves multiple engine samples and more aggressive test profiles that explore the boundaries of the engine to vehicle interface requirements. The hardware being tested may have evolved slightly from that in the development phase. Operational testing is conducted with mature hardware and includes acceptance testing of flight assets, resolving anomalies that occur in flight, continuing to expand the performance envelope, and implementing design upgrades. This paper will examine these phases of testing and their importance to the SSME program. Examples of tests conducted in each phase will also be presented.

First-ever evening public engine test of a Space Shuttle Main Engine

Science.gov (United States)

2001-01-01

Thousands of people watch the first-ever evening public engine test of a Space Shuttle Main Engine at NASA's John C. Stennis Space Center. The spectacular test marked Stennis Space Center's 20th anniversary celebration of the first Space Shuttle mission.

Engine Test Cell Aeroacoustics and Recommendations

National Research Council Canada - National Science Library

Tam, Christopher

2007-01-01

Ground testing of turbojet engines in test cells necessarily involves very high acoustic amplitudes, often enough and severe enough that testing is interrupted and facility hardware and test articles are damaged...

Intermediate Alcohol-Gasoline Blends, Fuels for Enabling Increased Engine Efficiency and Powertrain Possibilities

Energy Technology Data Exchange (ETDEWEB)

Splitter, Derek A [ORNL; Szybist, James P [ORNL

2014-01-01

The present study experimentally investigates spark-ignited combustion with 87 AKI E0 gasoline in its neat form and in mid-level alcohol-gasoline blends with 24% vol./vol. iso-butanol-gasoline (IB24) and 30% vol./vol. ethanol-gasoline (E30). A single-cylinder research engine is used with a low and high compression ratio of 9.2:1 and 11.85:1 respectively. The engine is equipped with hydraulically actuated valves, laboratory intake air, and is capable of external exhaust gas recirculation (EGR). All fuels are operated to full-load conditions with =1, using both 0% and 15% external cooled EGR. The results demonstrate that higher octane number bio-fuels better utilize higher compression ratios with high stoichiometric torque capability. Specifically, the unique properties of ethanol enabled a doubling of the stoichiometric torque capability with the 11.85:1 compression ratio using E30 as compared to 87 AKI, up to 20 bar IMEPg at =1 (with 15% EGR, 18.5 bar with 0% EGR). EGR was shown to provide thermodynamic advantages with all fuels. The results demonstrate that E30 may further the downsizing and downspeeding of engines by achieving increased low speed torque, even with high compression ratios. The results suggest that at mid-level alcohol-gasoline blends, engine and vehicle optimization can offset the reduced fuel energy content of alcohol-gasoline blends, and likely reduce vehicle fuel consumption and tailpipe CO2 emissions.

Analysis and control of a hybrid vehicle powered by free-piston energy converter

OpenAIRE

Hansson, Jörgen

2006-01-01

The introduction of hybrid powertrains has made it possible to utilise unconventional engines as primary power units in vehicles. The free-piston energy converter (FPEC) is such an engine. It is a combination of a free-piston combustion engine and a linear electrical machine. The main features of this configuration are high efficiency and a rapid transient response. In this thesis the free-piston energy converter as part of a hybrid powertrain is studied. One issue of the FPEC is the generati...

Improved parent-reported mobility and achievement of individual goals on activity and participation level after functional power-training in young children with cerebral palsy: a double-baseline controlled trial.

Science.gov (United States)

van Vulpen, Liesbeth F; de Groot, Sonja; Rameckers, Eugene A; Becher, Jules G; Dallmeijer, Annet J

2018-03-07

In children with cerebral palsy (CP), strength training programs to improve walking capacity and participation in activities of daily living are commonly used in clinical practice, despite lacking evidence of its effectiveness. It has been suggested that strength training with high movement velocity could be more effective than traditional resistance training to improve functional abilities such as walking. In a recently published study, we have demonstrated the positive effects of functional high-velocity resistance (power) training on muscle strength and walking capacity in young children with CP. Whether this type of training is also effective in achieving individual predefined goals in daily activities and self-reported mobility limitations, has not yet been described however. To evaluate the effect of functional power-training on parent-reported mobility and achievement of individual goals on activity and participation level in young children with CP. A double-baseline design was used to compare a 14-week period usual care with a 14-week period of functional power-training (3 times a week) and a follow-up period of 14-weeks. Twenty-two children with spastic CP (13 bilateral, GMFCS level I (N=10) and level II (N=12), mean age 7.5 years (SD 1.8, range 4-10 y)) and their parents participated. Outcome measures were goal attainment scaling (GAS) of individual daily activity related treatment goals, mobility performance as measured using the Functional Mobility Scale (FMS-5m, 50m and 500m), and the parent-reported Mobility Questionnaire (MobQues). After power-training, 86% of children achieved or exceeded their goal, compared with 14% in the usual care period (pfunctional power-training was 10 times higher, compared with the usual care period (Relative Risk=10.0 with 95%CI 1.4 - 71.3). No changes were found in the FMS-5m and FMS-50m categories. Improvement on the MobQues was significantly greater after power-training compared with usual care (7.9% (95% CI 2.7 - 13

UAV Mission Optimization through Hybrid-Electric Propulsion

Science.gov (United States)

Blackwelder, Philip Scott

Hybrid-electric powertrain leverages the superior range of petrol based systems with the quiet and emission free benefits of electric propulsion. The major caveat to hybrid-electric powertrain in an airplane is that it is inherently heavier than conventional petroleum powertrain due mostly to the low energy density of battery technology. The first goal of this research is to develop mission planning code to match powertrain components for a small-scale unmanned aerial vehicle (UAV) to complete a standard surveillance mission within a set of user input parameters. The second goal is to promote low acoustic profile loitering through mid-flight engine starting. The two means by which midmission engine starting will be addressed is through reverse thrust from the propeller and a servo actuated gear to couple and decouple the engine and motor. The mission planning code calculates the power required to complete a mission and assists the user in sourcing powertrain components including the propeller, motor, battery, motor controller, engine and fuel. Reverse thrust engine starting involves characterizing an off the shelf variable pitch propeller and using its torque coefficient to calculate the advance ratio required to provide sufficient torque and speed to start an engine. Geared engine starting works like the starter in a conventional automobile. A servo actuated gear will couple the motor to the engine to start it and decouple once the engine has started. Reverse thrust engine starting was unsuccessful due to limitations of available off the shelf variable pitch propellers. However, reverse thrust engine starting could be realized through a custom larger diameter propeller. Geared engine starting was a success, though the system was unable to run fully as intended. Due to counter-clockwise crank rotation of the engine and the right-hand threads on the crankshaft, cranking the engine resulted in the nut securing the engine starter gear to back off as the engine cranked

78 FR 48795 - Airworthiness Directives; BRP-Powertrain GmbH & Co KG Rotax Reciprocating Engines

Science.gov (United States)

2013-08-12

... AD to prevent excessive oil consumption, which could result in an in-flight engine shutdown, forced... consumption, which could result in an in-flight engine shutdown, forced landing, and damage to the airplane... average labor rate is $85 per hour. Based on these figures, we estimate the cost of this AD on U.S...

Initial testing of a variable-stroke Stirling engine

Science.gov (United States)

Thieme, L. G.

1985-01-01

In support of the U.S. Department of Energy's Stirling Engine Highway Vehicle Systems Program, NASA Lewis Research Center is evaluating variable-stroke control for Stirling engines. The engine being tested is the Advenco Stirling engine; this engine was manufactured by Philips Research Laboratories of the Netherlands and uses a variable-angle swash-plate drive to achieve variable stroke operation. The engine is described, initial steady-state test data taken at Lewis are presented, a major drive system failure and subsequent modifications are described. Computer simulation results are presented to show potential part-load efficiency gains with variable-stroke control.

40 CFR 1065.405 - Test engine preparation and maintenance.

Science.gov (United States)

2010-07-01

... has undergone a stabilization step (or in-use operation). If the engine has not already been... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Test engine preparation and...) AIR POLLUTION CONTROLS ENGINE-TESTING PROCEDURES Engine Selection, Preparation, and Maintenance § 1065...

40 CFR 91.409 - Engine dynamometer test run.

Science.gov (United States)

2010-07-01

... at rated speed and maximum power for 25 to 30 minutes; (iv) Option. For four-stroke engines, where... 40 Protection of Environment 20 2010-07-01 2010-07-01 false Engine dynamometer test run. 91.409... (CONTINUED) CONTROL OF EMISSIONS FROM MARINE SPARK-IGNITION ENGINES Gaseous Exhaust Test Procedures § 91.409...

Mechanical design of a free-wheel clutch for the thermal engine of a parallel hybrid vehicle with thermal and electrical power-train; Conception mecanique d'un accouplement a roue libre pour le moteur thermique d'un vehicule hybride parallele thermique et electrique

Energy Technology Data Exchange (ETDEWEB)

Santin, J.J.

2001-07-01

This thesis deals with the design of a free-wheel clutch. This unit is intended to replace the automated dry single-plate clutch of a parallel hybrid car with thermal and electric power-train. Furthermore, the car is a single shaft zero emission vehicle fitted with a controlled gearbox. Chapter one focuses on the type of hybrid vehicle studied. It shows the need to isolate the engine from the rest of the drive train, depending on the driving conditions. Chapter two presents and compares the two alternatives: automated clutch and free-wheel. In order to develop the free-wheel option, the torsional vibrations in the automotive drive line had to be closely studied. It required the design of a specific modular tool, as presented in chapter three, with the help of MATLAB SIMULINK. Lastly, chapter four shows how this tool was used during the design stage and specifies the way to build it. The free-wheel is then to be fitted to a prototype hybrid vehicle, constructed by both the LAMIH and PSA. (author)

Physical and engineering aspects of a fusion engineering test facility based on mirror confinement

International Nuclear Information System (INIS)

Kawabe, T.; Hirayama, S.; Hojo, H.; Kozaki, Y.; Yoshikawa, K.

1986-01-01

Controlled fusion research has accomplished great progress in the field of confinement of high-density and high-temperature plasmas and breakeven experiments are expected before the end of the 1980s. Many experiments have been proposed as the next step for fusion research. Among them is the study of ignited plasmas and another is the study of fusion engineering. Some of the important studies in fusion engineering are the integrated test in a fusion reactor environment as well as tests of first-wall materials and of the reactor structures, and test for tritium breeding and blanket modules or submodules. An ideal neutron source for the study of fusion engineering is the deuterium-tritium (D-T) fusion plasma itself. A neutron facility based on a D-T-burning plasma consists of all of the components that a real fusion power reactor would have, so eventually the integrated test for fusion reactor engineering can be done as well as the tests for each engineering component

76 FR 57696 - Approval and Promulgation of Implementation Plans; New York; Motor Vehicle Enhanced Inspection...

Science.gov (United States)

2011-09-16

... part of the sophisticated vehicle powertrain management system and is designed to detect engine and... current NYMA I/ (NYVIP and NYTEST M Programs) Post-NYTEST Non-electric and non-diesel Emissions Test Type... the 1996 SIP revision for the NYSDMV sponsored automotive technician training program. MOBILE6 does...

Engineered Barrier Test Facility status report, 1984

International Nuclear Information System (INIS)

Phillips, S.J.; Adams, M.R.; Gilbert, T.W.; Meinhardt, C.C.; Mitchell, R.M.; Waugh, W.J.

1985-02-01

This report provides a general summary of activities completed to date at the Hanford Engineered Barrier Test Facility. This facility is used to test and compare construction practices and performance of alternative designs of engineered barrier cover systems. These cover systems are being evaluated for potential use for isolation and confinement of buried waste disposal structures

Engineered Barrier Testing at the INEEL Engineered Barriers Test Facility: FY-1997 and FY-1998

International Nuclear Information System (INIS)

Keck, K. N.; Porro, I.

1998-01-01

Engineered barriers of two designs are being tested at the Engineered Barriers Test Facility (EBTF) at the Idaho National Engineering and Environmental Laboratory. This report describes the test facility, barrier designs, and instruments used to monitor the test plots. Wetting tests conducted on the test plots in FY-97 are described and data collected from monitoring the test plots before, during and after the wetting tests are used to evaluate the performance of the covers during FY-97 and FY-98. Replicates of two engineered barrier designs were constructed in the EBTF cells. The first design comprises a thick, vegetated soil cover. The second design incorporates a capillary/biobarrier within the vegtated soil cover. The capillary barrier uses the textural break between an upper, fine textured soil and a lower, coarser-textured gravel layer to inhibit drainage under unsaturated conditions while increasing soil moisture storage in the root zone. Evaporation and transpiration by plants (although the test plots have not yet been vegetated) are used to recycle water stored in the soil back to the atmosphere. A geotextile fabric is used to maintain separation of the soil and gravel layers. A thick layer of cobbles beneath the gravel layer serves as a biobarrier to prevent intrusion of plant roots and burrowing animals into underlying waste (there is no waste in the test plots). Each test plot was instrumented with time domain reflectometry probes and neutron probe access tubes to measure moisture contents, tensiometers, heat dissipation sensors, and thermocouple psychrometers to measure matric potentials, thermocouples to measure soil temperature, and ion-exchange resin beads to monitor tracer movement. Each drainage sump is equipped with a tipping bucket instrument and pressure transducer to measure drainage. Precipitation is measured using a heated rain gauge located at the EBTF. Instrument calibration equation coefficients are presented, and data reduction

MANUFACTURING AND TESTING OF A V-TYPE STIRLING ENGINE

Directory of Open Access Journals (Sweden)

B. Demir

2012-01-01

Full Text Available In this study, a V-type Stirling engine with 163 cc total swept volume was designed and manufactured. Air was used as working fluid. Performance tests were conducted at the range of 1-3 bar charge pressure and within the range of hot source temperature 700-1050 °C. Experimental results are given. Variation of engine power and torque with hot source temperature at various air charge pressure are tested. Also variation of engine torque with engine speed for different air charge pressure are tested. According to experimental analysis, the maximum engine power was obtained as 21.334 W at 1050 ˚C hot source temperature and 1.5 bars charge pressure.

Test plan for engineering scale electrostatic enclosure demonstration

International Nuclear Information System (INIS)

Meyer, L.C.

1993-02-01

This test plan describes experimental details of an engineering-scale electrostatic enclosure demonstration to be performed at the Idaho National Engineering Laboratory in fiscal year (FY)-93. This demonstration will investigate, in the engineering scale, the feasibility of using electrostatic enclosures and devices to control the spread of contaminants during transuranic waste handling operations. Test objectives, detailed experimental procedures, and data quality objectives necessary to perform the FY-93 experiments are included in this plan

Prototype Engineered Barrier System Field Tests

International Nuclear Information System (INIS)

Ramirez, A.L.; Beatty, J.; Buscheck, T.A.

1989-01-01

This paper presents selected preliminary results obtained during the first 54 days of the Prototype Engineered Barrier System Field Tests (PEBSFT) that are being performed in G-Tunnel within the Nevada Test Site. The test described is a precursor to the Engineered Barrier Systems Field Tests (EBSFT). The EBSFT will consist of in situ tests of the geohydrologic and geochemical environment in the near field (within a few meters) of heaters emplaced in welded tuff to simulate the thermal effects of waste packages. The PEBSFTs are being conducted to evaluate the applicability of measurement techniques, numerical models, and procedures for future investigations that will be conducted in the Exploratory Shaft Facilities of the Yucca Mountain Project (YMP). The paper discusses the evolution of hydrothermal behavior during the prototype test, including rock temperatures, changes in rock moisture content, air permeability of fractures, gas pressures, and rock mass gas-phase humidity. 10 refs., 12 figs

Environmental Testing of the NEXT PM1R Ion Engine

Science.gov (United States)

Snyder, John S.; Anderson, John R.; VanNoord, Jonathan L.; Soulas, George C.

2007-01-01

The NEXT propulsion system is an advanced ion propulsion system presently under development that is oriented towards robotic exploration of the solar system using solar electric power. The subsystem includes an ion engine, power processing unit, feed system components, and thruster gimbal. The Prototype Model engine PM1 was subjected to qualification-level environmental testing in 2006 to demonstrate compatibility with environments representative of anticipated mission requirements. Although the testing was largely successful, several issues were identified including the fragmentation of potting cement on the discharge and neutralizer cathode heater terminations during vibration which led to abbreviated thermal testing, and generation of particulate contamination from manufacturing processes and engine materials. The engine was reworked to address most of these findings, renamed PM1R, and the environmental test sequence was repeated. Thruster functional testing was performed before and after the vibration and thermal-vacuum tests. Random vibration testing, conducted with the thruster mated to the breadboard gimbal, was executed at 10.0 Grms for 2 min in each of three axes. Thermal-vacuum testing included three thermal cycles from 120 to 215 C with hot engine re-starts. Thruster performance was nominal throughout the test program, with minor variations in a few engine operating parameters likely caused by facility effects. There were no significant changes in engine performance as characterized by engine operating parameters, ion optics performance measurements, and beam current density measurements, indicating no significant changes to the hardware as a result of the environmental testing. The NEXT PM1R engine and the breadboard gimbal were found to be well-designed against environmental requirements based on the results reported herein. The redesigned cathode heater terminations successfully survived the vibration environments. Based on the results of this test

40 CFR 86.336-79 - Diesel engine test cycle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Diesel engine test cycle. 86.336-79... Diesel engine test cycle. (a) The following 13-mode cycle shall be followed in dynamometer operation... (CONTINUED) CONTROL OF EMISSIONS FROM NEW AND IN-USE HIGHWAY VEHICLES AND ENGINES Emission Regulations for...

Model-based design validation for advanced energy management strategies for electrified hybrid power trains using innovative vehicle hardware in the loop (VHIL) approach

International Nuclear Information System (INIS)

Mayyas, Abdel Ra'ouf; Kumar, Sushil; Pisu, Pierluigi; Rios, Jacqueline; Jethani, Puneet

2017-01-01

Highlights: •Vehicle hardware In-the-loop VHiL testing and validation is implemented in vehicle test bed. •Torque at the roller bench test is used to control the torque at wheels to reflect vehicle electrification symptoms. •Electrified powertrain with Equivalent Consumption Minimization Strategy is tested and validated using VHiL. •Fuel economy and power train performance is measured using high precision fuel measurement device. -- Abstract: Hybridization of automotive powertrains by using more than one type of energy converter is considered as an important step towards reducing fuel consumption and air pollutants. Specifically, the development of energy efficient, highly complex, alternative drive-train systems, in which the interactions of different energy converters play an important role, requires new design methods and processes. This paper discusses the inclusion of an alternative hybrid power train into an existing vehicle platform for maximum energy efficiency. The new proposed integrated Vehicle Hardware In-the-loop (VHiL) and Model Based Design (MBD) approach is utilized to evaluate the energy efficiency of electrified powertrain. In VHiL, a complete chassis system becomes an integrated part of the vehicle test bed. A complete conventional Internal Combustion Engine (ICE) powered vehicle is tested in roller bench test for the integration of energy efficient hybrid electric power train modules in closed-loop, real-time, feedback configuration. A model that is a replica of the test vehicle is executed – in real-time- where all hybrid power train modules are included. While the VHiL platform is controlling the signal exchange between the test bed automation software and the vehicle on-board controller, the road load exerted on the driving wheels is manipulated in closed –loop real-time manner in order to reflect all hybrid driving modes including: All Electric Range (AER), Electric Power Assist (EPA) and blended Modes (BM). Upon successful

Pretreatment Engineering Platform Phase 1 Final Test Report

Energy Technology Data Exchange (ETDEWEB)

Kurath, Dean E.; Hanson, Brady D.; Minette, Michael J.; Baldwin, David L.; Rapko, Brian M.; Mahoney, Lenna A.; Schonewill, Philip P.; Daniel, Richard C.; Eslinger, Paul W.; Huckaby, James L.; Billing, Justin M.; Sundar, Parameshwaran S.; Josephson, Gary B.; Toth, James J.; Yokuda, Satoru T.; Baer, Ellen BK; Barnes, Steven M.; Golovich, Elizabeth C.; Rassat, Scot D.; Brown, Christopher F.; Geeting, John GH; Sevigny, Gary J.; Casella, Amanda J.; Bontha, Jagannadha R.; Aaberg, Rosanne L.; Aker, Pamela M.; Guzman-Leong, Consuelo E.; Kimura, Marcia L.; Sundaram, S. K.; Pires, Richard P.; Wells, Beric E.; Bredt, Ofelia P.

2009-12-23

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project, Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to conduct testing to demonstrate the performance of the WTP Pretreatment Facility (PTF) leaching and ultrafiltration processes at an engineering-scale. In addition to the demonstration, the testing was to address specific technical issues identified in Issue Response Plan for Implementation of External Flowsheet Review Team (EFRT) Recommendations - M12, Undemonstrated Leaching Processes.( ) Testing was conducted in a 1/4.5-scale mock-up of the PTF ultrafiltration system, the Pretreatment Engineering Platform (PEP). Parallel laboratory testing was conducted in various PNNL laboratories to allow direct comparison of process performance at an engineering-scale and a laboratory-scale. This report presents and discusses the results of those tests.

Pretreatment Engineering Platform Phase 1 Final Test Report

International Nuclear Information System (INIS)

Kurath, Dean E.; Hanson, Brady D.; Minette, Michael J.; Baldwin, David L.; Rapko, Brian M.; Mahoney, Lenna A.; Schonewill, Philip P.; Daniel, Richard C.; Eslinger, Paul W.; Huckaby, James L.; Billing, Justin M.; Sundar, Parameshwaran S.; Josephson, Gary B.; Toth, James J.; Yokuda, Satoru T.; Baer, Ellen B.K.; Barnes, Steven M.; Golovich, Elizabeth C.; Rassat, Scot D.; Brown, Christopher F.; Geeting, John G.H.; Sevigny, Gary J.; Casella, Amanda J.; Bontha, Jagannadha R.; Aaberg, Rosanne L.; Aker, Pamela M.; Guzman-Leong, Consuelo E.; Kimura, Marcia L.; Sundaram, S.K.; Pires, Richard P.; Wells, Beric E.; Bredt, Ofelia P.

2009-01-01

Pacific Northwest National Laboratory (PNNL) was tasked by Bechtel National Inc. (BNI) on the River Protection Project, Hanford Tank Waste Treatment and Immobilization Plant (RPP-WTP) project to conduct testing to demonstrate the performance of the WTP Pretreatment Facility (PTF) leaching and ultrafiltration processes at an engineering-scale. In addition to the demonstration, the testing was to address specific technical issues identified in Issue Response Plan for Implementation of External Flowsheet Review Team (EFRT) Recommendations - M12, Undemonstrated Leaching Processes. Testing was conducted in a 1/4.5-scale mock-up of the PTF ultrafiltration system, the Pretreatment Engineering Platform (PEP). Parallel laboratory testing was conducted in various PNNL laboratories to allow direct comparison of process performance at an engineering-scale and a laboratory-scale. This report presents and discusses the results of those tests.

Two methodologies for physical penetration testing using social engineering

NARCIS (Netherlands)

Dimkov, T.; van Cleeff, A.; Pieters, Wolter; Hartel, Pieter H.

2010-01-01

Penetration tests on IT systems are sometimes coupled with physical penetration tests and social engineering. In physical penetration tests where social engineering is allowed, the penetration tester directly interacts with the employees. These interactions are usually based on deception and if not

Test/QA plan for the verification testing of diesel exhaust catalysts, particulate filters and engine modification control technologies for highway and nonroad use diesel engines

Science.gov (United States)

This ETV test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research (DER) describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR Part 89 for nonroad engines, will be ...

40 CFR 89.407 - Engine dynamometer test run.

Science.gov (United States)

2010-07-01

... supplied to the engine, the fuel temperature, the intake air humidity, and the observed barometric pressure... permitted to precondition the engine at rated speed and maximum horsepower until the oil and water... completion of the test. (3) It is permissible to change filter elements between test modes. (4) A leak check...

Computer-Aided System of Virtual Testing of Gas Turbine Engines

Directory of Open Access Journals (Sweden)

Rybakov Viktor N.

2016-01-01

Full Text Available The article describes the concept of a virtual lab that includes subsystem of gas turbine engine simulation, subsystem of experiment planning, subsystem of measurement errors simulation, subsystem of simulator identification and others. The basis for virtual lab development is the computer-aided system of thermogasdynamic research and analysis “ASTRA”. The features of gas turbine engine transient modes simulator are described. The principal difference between the simulators of transient and stationary modes of gas turbine engines is that the energy balance of the compressor and turbine becomes not applicable. The computer-aided system of virtual gas turbine engine testing was created using the developed transient modes simulator. This system solves the tasks of operational (throttling, speed, climatic, altitude characteristics calculation, analysis of transient dynamics and selection of optimal control laws. Besides, the system of virtual gas turbine engine testing is a clear demonstration of gas turbine engine working process and the regularities of engine elements collaboration. The interface of the system of virtual gas turbine engine testing is described in the article and some screenshots of the interface elements are provided. The developed system of virtual gas turbine engine testing provides means for reducing the laboriousness of gas turbine engines testing. Besides, the implementation of this system in the learning process allows the diversification of lab works and therefore improve the quality of training.

40 CFR 86.335-79 - Gasoline-fueled engine test cycle.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Gasoline-fueled engine test cycle. 86....335-79 Gasoline-fueled engine test cycle. (a) The following test sequence shall be followed in... operating the engine at the higher approved load setting during cycle 1 and at the lower approved load...

Phase 1 Development Testing of the Advanced Manufacturing Demonstrator Engine

Science.gov (United States)

Case, Nicholas L.; Eddleman, David E.; Calvert, Marty R.; Bullard, David B.; Martin, Michael A.; Wall, Thomas R.

2016-01-01

The Additive Manufacturing Development Breadboard Engine (BBE) is a pressure-fed liquid oxygen/pump-fed liquid hydrogen (LOX/LH2) expander cycle engine that was built and operated by NASA at Marshall Space Flight Center's East Test Area. The breadboard engine was conceived as a technology demonstrator for the additive manufacturing technologies for an advanced upper stage prototype engine. The components tested on the breadboard engine included an ablative chamber, injector, main fuel valve, turbine bypass valve, a main oxidizer valve, a mixer and the fuel turbopump. All parts minus the ablative chamber were additively manufactured. The BBE was successfully hot fire tested seven times. Data collected from the test series will be used for follow on demonstration tests with a liquid oxygen turbopump and a regeneratively cooled chamber and nozzle.

Environmental Testing of the NEXT PM1 Ion Engine

Science.gov (United States)

Synder, John S.; Anderson, John R.; VanNoord, Jonathan L.; Soulas, George C.

2008-01-01

The NEXT propulsion system is an advanced ion propulsion system presently under development that is oriented towards robotic exploration of the solar system using solar electric power. The Prototype Model engine PM1 was subjected to qualification-level environmental testing to demonstrate compatibility with environments representative of anticipated mission requirements. Random vibration testing, conducted with the thruster mated to the breadboard gimbal, was executed at 10.0 Grms for 2 minutes in each of three axes. Thermal-vacuum testing included a deep cold soak of the engine to temperatures of -168 C and thermal cycling from -120 to 203 C. Although the testing was largely successful, several issues were identified including the fragmentation of potting cement on the discharge and neutralizer cathode heater terminations during vibration which led to abbreviated thermal testing, and generation of particulate contamination from manufacturing processes and engine materials. Thruster performance was nominal throughout the test program, with minor variations in some engine operating parameters likely caused by facility effects. In general, the NEXT PM1 engine and the breadboard gimbal were found to be well-designed against environmental requirements based on the results reported herein. After resolution of the findings from this test program the hardware environmental qualification program can proceed with confidence.

Tests of the Daimler D-IVa Engine at a High Altitude Test Bench

Science.gov (United States)

Noack, W G

1920-01-01

Reports of tests of a Daimler IVa engine at the test-bench at Friedrichshafen, show that the decrease of power of that engine, at high altitudes, was established, and that the manner of its working when air is supplied at a certain pressure was explained. These tests were preparatory to the installation of compressors in giant aircraft for the purpose of maintaining constant power at high altitudes.

COMPARISON OF PARALLEL AND SERIES HYBRID POWERTRAINS FOR TRANSIT BUS APPLICATION

Energy Technology Data Exchange (ETDEWEB)

Gao, Zhiming [ORNL; Daw, C Stuart [ORNL; Smith, David E [ORNL; Jones, Perry T [ORNL; LaClair, Tim J [ORNL; Parks, II, James E [ORNL

2016-01-01

The fuel economy and emissions of both conventional and hybrid buses equipped with emissions aftertreatment were evaluated via computational simulation for six representative city bus drive cycles. Both series and parallel configurations for the hybrid case were studied. The simulation results indicate that series hybrid buses have the greatest overall advantage in fuel economy. The series and parallel hybrid buses were predicted to produce similar CO and HC tailpipe emissions but were also predicted to have reduced NOx tailpipe emissions compared to the conventional bus in higher speed cycles. For the New York bus cycle (NYBC), which has the lowest average speed among the cycles evaluated, the series bus tailpipe emissions were somewhat higher than they were for the conventional bus, while the parallel hybrid bus had significantly lower tailpipe emissions. All three bus powertrains were found to require periodic active DPF regeneration to maintain PM control. Plug-in operation of series hybrid buses appears to offer significant fuel economy benefits and is easily employed due to the relatively large battery capacity that is typical of the series hybrid configuration.

Software for Preprocessing Data from Rocket-Engine Tests

Science.gov (United States)

Cheng, Chiu-Fu

2004-01-01

Three computer programs have been written to preprocess digitized outputs of sensors during rocket-engine tests at Stennis Space Center (SSC). The programs apply exclusively to the SSC E test-stand complex and utilize the SSC file format. The programs are the following: Engineering Units Generator (EUGEN) converts sensor-output-measurement data to engineering units. The inputs to EUGEN are raw binary test-data files, which include the voltage data, a list identifying the data channels, and time codes. EUGEN effects conversion by use of a file that contains calibration coefficients for each channel. QUICKLOOK enables immediate viewing of a few selected channels of data, in contradistinction to viewing only after post-test processing (which can take 30 minutes to several hours depending on the number of channels and other test parameters) of data from all channels. QUICKLOOK converts the selected data into a form in which they can be plotted in engineering units by use of Winplot (a free graphing program written by Rick Paris). EUPLOT provides a quick means for looking at data files generated by EUGEN without the necessity of relying on the PV-WAVE based plotting software.

Pratt & Whitney Advanced Ducted Propulsor (ADP) Engine Test in 40x80ft w.t.: Engineers Peter

Science.gov (United States)

1993-01-01

Pratt & Whitney Advanced Ducted Propulsor (ADP) Engine Test in 40x80ft w.t.: Engineers Peter Zell (left) and Dr Clifton Horne (right) are shown preparing a laser light sheet for a flow visualization test. Shown standing in the nacelle of the ADP is John Girvin, senior test engineer for Pratt & Whitney.

Tests Of A Stirling-Engine Power Converter

Science.gov (United States)

Dochat, George

1995-01-01

Report describes acceptance tests of power converter consisting of pair of opposed free-piston Stirling engines driving linear alternators. Stirling engines offer potential for extremely long life, high reliability, high efficiency at low hot-to-cold temperature ratios, and relatively low heater-head temperatures.

Engine Performance Test of the 1975 Chrysler - Nissan Model CN633 Diesel Engine

Science.gov (United States)

1975-09-01

An engine test of the Chrysler-Nissan Model CN633 diesel engine was performed to determine its steady-state fuel consumption and emissions (HC, CO, NOx) maps. The data acquired are summarized in this report.

14 CFR 33.96 - Engine tests in auxiliary power unit (APU) mode.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Engine tests in auxiliary power unit (APU... TRANSPORTATION AIRCRAFT AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.96 Engine tests in auxiliary power unit (APU) mode. If the engine is designed with a propeller brake which...

The Evaluation of the Impact of New Technologies for Different Powertrain Medium-Duty Trucks on Fuel Consumption

Energy Technology Data Exchange (ETDEWEB)

Wang, Lijuan; Duran, Adam; Kelly, Kenneth; Konan, Arnaud; Lammert, Michael; Prohaska, Robert

2016-09-27

In this paper, researchers at the National Renewable Energy Laboratory present the results of simulation studies to evaluate potential fuel savings as a result of improvements to vehicle rolling resistance, coefficient of drag, and vehicle weight as well as hybridization for four powertrains for medium-duty parcel delivery vehicles. The vehicles will be modeled and simulated over 1,290 real-world driving trips to determine the fuel savings potential based on improvements to each technology and to identify best use cases for each platform. The results of impacts of new technologies on fuel saving will be presented, and the most favorable driving routes on which to adopt them will be explored.

Dictionary materials engineering, materials testing

International Nuclear Information System (INIS)

1994-01-01

This dictionary contains about 9,500 entries in each part of the following fields: 1) Materials using and selection; 2) Mechanical engineering materials -Metallic materials - Non-metallic inorganic materials - Plastics - Composites -Materials damage and protection; 3) Electrical and electronics materials -Conductor materials - Semiconductors - magnetic materials - Dielectric materials - non-conducting materials; 4) Materials testing - Mechanical methods - Analytical methods - Structure investigation - Complex methods - Measurement of physical properties - Non-destructive testing. (orig.) [de

Space Shuttle Main Engine Public Test Firing

Science.gov (United States)

2000-01-01

A new NASA Space Shuttle Main Engine (SSME) roars to the approval of more than 2,000 people who came to John C. Stennis Space Center in Hancock County, Miss., on July 25 for a flight-certification test of the SSME Block II configuration. The engine, a new and significantly upgraded shuttle engine, was delivered to NASA's Kennedy Space Center in Florida for use on future shuttle missions. Spectators were able to experience the 'shake, rattle and roar' of the engine, which ran for 520 seconds - the length of time it takes a shuttle to reach orbit.

14 CFR 33.91 - Engine system and component tests.

Science.gov (United States)

2010-01-01

... AIRWORTHINESS STANDARDS: AIRCRAFT ENGINES Block Tests; Turbine Aircraft Engines § 33.91 Engine system and..., reliability, and durability. (c) Each unpressurized hydraulic fluid tank may not fail or leak when subjected... hydraulic fluid tank must meet the requirements of § 33.64. (d) For an engine type certificated for use in...

Role of well testing in civil engineering

International Nuclear Information System (INIS)

Banks, D.

1981-01-01

Purpose of well testing is to derive a value of the permeability of the geologic medium or to measure the velocity or quantity of fluid flow. The types of tests typically employed on civil engineering projects are simple borehole tests, packer or pressure tests in boreholes, permeameter tests, well pumping tests, and in-hole tests using well flow meters or tracer tests. New problem areas which demand new approaches are mentioned

Optimization and Model Validation of Operation Control Strategies for a Novel Dual-Motor Coupling-Propulsion Pure Electric Vehicle

Directory of Open Access Journals (Sweden)

Jianjun Hu

2018-03-01

Full Text Available The strict operational condition of driving motors for vehicles propels the development of more complicated configurations in pure electric vehicles (PEVs. Multi-power-source powertrain configurations are one of the efficient technologies to reduce the manufacturing difficulty of driving motors. However, most of the existing studies are predominantly focused on optimal designs of powertrains and power distribution between the engine and motor of hybrid electric vehicles, which are not appropriate for PEVs. This paper proposes a novel dual-motor coupling-propulsion powertrain system that improves the dynamic and economic performance of the powertrain system in PEVs. The proposed powertrain system can realize both the single-motor driving mode and dual-motor coupling driving mode. The driving modes are divided and a power distribution strategy for the different driving modes based on an optimal system efficiency rule is employed, which enhances the performance of the proposed system. Further, a mode-switching strategy that ensures driving comfort by preventing jerk during mode switching is incorporated into the system. The results of comparative evaluations that were conducted using a dual-motor electric vehicle model implemented in MATLAB/Simulink, indicate that the mileage and dynamic performance of the proposed powertrain system are significantly better than those of the traditional single-motor powertrain system.

Design and test of aircraft engine isolators for reduced interior noise

Science.gov (United States)

Unruh, J. F.; Scheidt, D. C.

1982-01-01

Improved engine vibration isolation was proposed to be the most weight and cost efficient retrofit structure-borne noise control measure for single engine general aviation aircraft. A study was carried out the objectives: (1) to develop an engine isolator design specification for reduced interior noise transmission, (2) select/design candidate isolators to meet a 15 dB noise reduction design goal, and (3) carry out a proof of concept evaluation test. Analytical model of the engine, vibration isolators and engine mount structure were coupled to an empirical model of the fuselage for noise transmission evaluation. The model was used to develop engine isolator dynamic properties design specification for reduced noise transmission. Candidate isolators ere chosen from available product literature and retrofit to a test aircraft. A laboratory based test procedure was then developed to simulate engine induced noise transmission in the aircraft for a proof of concept evaluation test. Three candidate isolator configurations were evaluated for reduced structure-borne noise transmission relative to the original equipment isolators.

40 CFR 90.1204 - Maintenance, aging and testing of engines.

Science.gov (United States)

2010-07-01

... engines. 90.1204 Section 90.1204 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR... sample unless that engine experiences catastrophic mechanical failure or safety concerns requiring major... for engines with the amount of service and age of the test engine. (d) After aging each engine to at...

Engineering the future of military tactical vehicles and systems with modeling and simulation

Science.gov (United States)

Loew, Matthew; Watters, Brock

2005-05-01

Stewart & Stevenson has developed a Modeling and Simulation approach based on Systems Engineering principles for the development of future military vehicles and systems. This approach starts with a requirements analysis phase that captures and distills the design requirements into a list of parameterized values. A series of executable engineering models are constructed to allow the requirements to be transformed into systems with definable architectures with increasing levels of fidelity. Required performance parameters are available for importation into a variety of modeling and simulation tools including PTC Pro/ENGINEER (for initial engineering models, mechanisms, packaging, and detailed 3-Dimensional solid models), LMS International Virtual.Lab Motion (for vehicle dynamics and ride analysis) and AVL Cruise (Powertrain simulations). Structural analysis and optimization (performed in ANSYS, Pro/MECHANICA, and Altair OptiStruct) is based on the initial geometry from Pro/ENGINEER. Spreadsheets are used for requirements analysis, design documentation and first-order studies. Collectively, these models serve as templates for all design activities. Design variables initially studied within a simplified system model can be cascaded down as the new requirements for a sub-system model. By utilizing this approach premature decisions on systems architectures can be avoided. Ultimately, the systems that are developed are optimally able to meet the requirements by utilizing this top-down approach. Additionally, this M&S approach is seen as a life-cycle tool useful in initially assisting with project management activities through the initial and detail design phases and serves as a template for testing and validation/verification activities. Furthermore, because of the multi-tiered approach, there is natural re-use possible with the models as well.

40 CFR 1048.301 - When must I test my production-line engines?

Science.gov (United States)

2010-07-01

... engines? 1048.301 Section 1048.301 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Testing Production-line Engines § 1048.301 When must I test my production-line engines? (a) If you produce engines...

The electric motor in the hybrid vehicle. A comparison of three different types of electric motors; Der Elektromotor im Hybridfahrzeug. Vergleich von drei unterschiedlichen Elektromotorentypen

Energy Technology Data Exchange (ETDEWEB)

Petschnik, Harald

2009-07-01

According to the experts, hybrid technology is the key technology in the automotive industry for the next few decades. Many of the well established automobile manufacturers are focusing their research and development activities on this upcoming technology. The big advantage of hybrid vehicles is the electrified powertrain. Due to intelligent combination of the combustion- and electric engine, the benefits of the two different powertrain configurations can be used. The following research is concerned and closely examines the role of the electric engine in the hybrid vehicle. The scope of the research is focused on the demands of an electric engine, the technical configuration, functionality and economy of three different engine types which are often used in the serial production and prototyping. In order to make a direct comparison of the performance of this different engine types, they were all tested in a go-cart. The go-carts for each engine were constructed in the same way. The interpretation of the measurement results showed that the synchronous engine with permanent magnets had the best performance when considering the level of electrical efficiency, closely followed by the switched reluctance motor. The efficiency of the electrical motor makes a high contribution to the total efficiency of the vehicle. The measurement result confirms the selection of a synchronous motor is, under consideration of the electrical efficiency, the most advantageous solution for hybrid vehicles. (orig.)

Towards sustainable urban transportation: Test, demonstration and development of fuel cell and hybrid-electric buses

International Nuclear Information System (INIS)

Folkesson, Anders

2008-05-01

Several aspects make today's transport system non-sustainable: - Production, transport and combustion of fossil fuels lead to global and local environmental problems. - Oil dependency in the transport sector may lead to economical and political instability. - Air pollution, noise, congestion and land-use may jeopardise public health and quality of life, especially in urban areas. In a sustainable urban transport system most trips are made with public transport because high convenience and comfort makes travelling with public transport attractive. In terms of emissions, including noise, the vehicles are environmentally sustainable, locally as well as globally. Vehicles are energy-efficient and the primary energy stems from renewable sources. Costs are reasonable for all involved, from passengers, bus operators and transport authorities to vehicle manufacturers. The system is thus commercially viable on its own merits. This thesis presents the results from three projects involving different concept buses, all with different powertrains. The first two projects included technical evaluations, including tests, of two different fuel cell buses. The third project focussed on development of a series hybrid-bus with internal combustion engine intended for production around 2010. The research on the fuel cell buses included evaluations of the energy efficiency improvement potential using energy mapping and vehicle simulations. Attitudes to hydrogen fuel cell buses among passengers, bus drivers and bus operators were investigated. Safety aspects of hydrogen as a vehicle fuel were analysed and the use of hydrogen compared to electrical energy storage were also investigated. One main conclusion is that a city bus should be considered as one energy system, because auxiliaries contribute largely to the energy use. Focussing only on the powertrain is not sufficient. The importance of mitigating losses far down an energy conversion chain is emphasised. The Scania hybrid fuel cell

Future Potential of Hybrid and Diesel Powertrains in the U.S. Light-duty Vehicle Market

Energy Technology Data Exchange (ETDEWEB)

Greene, D.L.

2004-08-23

Diesel and hybrid technologies each have the potential to increase light-duty vehicle fuel economy by a third or more without loss of performance, yet these technologies have typically been excluded from technical assessments of fuel economy potential on the grounds that hybrids are too expensive and diesels cannot meet Tier 2 emissions standards. Recently, hybrid costs have come down and the few hybrid makes available are selling well. Diesels have made great strides in reducing particulate and nitrogen oxide emissions, and are likely though not certain to meet future standards. In light of these developments, this study takes a detailed look at the market potential of these two powertrain technologies and their possible impacts on light-duty vehicle fuel economy. A nested multinomial logit model of vehicle choice was calibrated to 2002 model year sales of 930 makes, models and engine-transmission configurations. Based on an assessment of the status and outlook for the two technologies, market shares were predicted for 2008, 2012 and beyond, assuming no additional increase in fuel economy standards or other new policy initiatives. Current tax incentives for hybrids are assumed to be phased out by 2008. Given announced and likely introductions by 2008, hybrids could capture 4-7% and diesels 2-4% of the light-duty market. Based on our best guesses for further introductions, these shares could increase to 10-15% for hybrids and 4-7% for diesels by 2012. The resulting impacts on fleet average fuel economy would be about +2% in 2008 and +4% in 2012. If diesels and hybrids were widely available across vehicle classes, makes, and models, they could capture 40% or more of the light-duty vehicle market.

Life-cycle analysis of energy and greenhouse gas emissions of automotive fuels in India: Part 1 – Tank-to-Wheel analysis

International Nuclear Information System (INIS)

Gupta, S.; Patil, V.; Himabindu, M.; Ravikrishna, R.V.

2016-01-01

As part of a two-part life cycle efficiency and greenhouse gas emission analysis for various automotive fuels in the Indian context, this paper presents the first part, i.e., Tank-to-Wheel analysis of various fuel/powertrain configurations for a subcompact passenger car. The Tank-to-Wheel analysis was applied to 28 fuel/powertrain configurations using fuels such as gasoline, diesel, compressed natural gas, liquefied petroleum gas and hydrogen with various conventional and hybrid electric powertrains. The gasoline-equivalent fuel economy and carbon dioxide emission results for individual fuel/powertrain configuration are evaluated and compared. It is found that the split hybrid configuration is best among hybrids as it leads to fuel economy improvement and carbon dioxide emissions reduction by 20–40% over the Indian drive cycle. Further, the engine efficiency, engine on-off time and regenerative braking energy assessment is done to evaluate the causes for higher energy efficiency of hybrid electric vehicles. The hybridization increases average engine efficiency by 10–60% which includes 19–23% of energy recovered at wheel through regenerative braking over the drive cycle. Overall, the Tank-to-Wheel energy use and efficiency results are evaluated for all fuel/powertrain configurations which show Battery Electric Vehicle, fuel cell vehicles and diesel hybrids are near and long term energy efficient vehicle configurations. - Highlights: • Tank-to-Wheel energy use & CO_2 emissions for subcompact car on Indian driving cycle. • Gasoline, diesel, CNG, LPG, hydrogen and electric vehicles are evaluated in this study. • First comprehensive Tank-to-Wheel analysis for India on small passenger car platform. • Parallel, series and split hybrid electric vehicles with various fuels are analysed.

Test-Driven, Model-Based Systems Engineering

DEFF Research Database (Denmark)

Munck, Allan

Hearing systems have evolved over many years from simple mechanical devices (horns) to electronic units consisting of microphones, amplifiers, analog filters, loudspeakers, batteries, etc. Digital signal processors replaced analog filters to provide better performance end new features. Central....... This thesis concerns methods for identifying, selecting and implementing tools for various aspects of model-based systems engineering. A comprehensive method was proposed that include several novel steps such as techniques for analyzing the gap between requirements and tool capabilities. The method...... was verified with good results in two case studies for selection of a traceability tool (single-tool scenario) and a set of modeling tools (multi-tool scenarios). Models must be subjected to testing to allow engineers to predict functionality and performance of systems. Test-first strategies are known...

Fuzzy/Neural Software Estimates Costs of Rocket-Engine Tests

Science.gov (United States)

Douglas, Freddie; Bourgeois, Edit Kaminsky

2005-01-01

The Highly Accurate Cost Estimating Model (HACEM) is a software system for estimating the costs of testing rocket engines and components at Stennis Space Center. HACEM is built on a foundation of adaptive-network-based fuzzy inference systems (ANFIS) a hybrid software concept that combines the adaptive capabilities of neural networks with the ease of development and additional benefits of fuzzy-logic-based systems. In ANFIS, fuzzy inference systems are trained by use of neural networks. HACEM includes selectable subsystems that utilize various numbers and types of inputs, various numbers of fuzzy membership functions, and various input-preprocessing techniques. The inputs to HACEM are parameters of specific tests or series of tests. These parameters include test type (component or engine test), number and duration of tests, and thrust level(s) (in the case of engine tests). The ANFIS in HACEM are trained by use of sets of these parameters, along with costs of past tests. Thereafter, the user feeds HACEM a simple input text file that contains the parameters of a planned test or series of tests, the user selects the desired HACEM subsystem, and the subsystem processes the parameters into an estimate of cost(s).

Introduction to nuclear test engineering

International Nuclear Information System (INIS)

O'Neal, W.C.; Paquette, D.L.

1982-01-01

The basic information in this report is from a vu-graph presentation prepared to acquaint new or prospective employees with the Nuclear Test Engineering Division (NTED). Additional information has been added here to enhance a reader's understanding when reviewing the material after hearing the presentation, or in lieu of attending a presentation

Successful testing of an emergency diesel generator engine at very low load

International Nuclear Information System (INIS)

Killinger, A.; Loeper, St.

2001-01-01

For more than 30 years, the nuclear power industry has been concerned about the ability of emergency diesel generator sets (EDGs) to operate for extended periods of time at low loads (typically less than 33% of design rating) and still be capable of meeting their design safety requirement. Most diesel engine manufacturers today still caution owners and operators to avoid running their diesel engines for extended periods of time at low loads. At one nuclear power plant, the emergency electrical bus arrangement only required approximately 25% of the EDG's design rating, which necessitated that the plant operators monitor EDG operating hours and periodically increase electrical load. In order to eliminate the plant operations burden of periodically loading the EDGs, the nuclear power plant decided to conduct a low-load test of a ''spare'' diesel engine. A SACM Model UD45V16S5D diesel engine was returned to the factory in Mulhouse, France where the week long testing at rated speed and 3% of design rating was completed. The test demonstrated that the engine was capable of operating for seven days (168 hours) at very low loads, with no loss of performance and no unusual internal wear or degradation. The planning and inspections associated with preparing the diesel engine for the test, the engine monitoring performed during the test, the final test results, and the results and material condition of the engine following the test are described. The successful diesel engine low-load test resulted in the elimination of unnecessary nuclear power plant operation restrictions that were based on old concerns about long-term, low-load operation of diesel engines. The paper describes the significance of this diesel engine test to the nuclear power plant and the entire nuclear power industry. (author)

Powertrain Component Inspection from Mid-Level Blends Vehicle Aging Study

Energy Technology Data Exchange (ETDEWEB)

Shoffner, Brent [Southwest Research Institute, San Antonio; Johnson, Ryan [Southwest Research Institute, San Antonio; Heimrich, Martin J. [Southwest Research Institute, San Antonio; Lochte, Michael [Southwest Research Institute, San Antonio

2010-11-01

The Energy Independence and Security Act of 2007 calls on the nation to significantly increase its use of renewable fuels to meet its transportation energy needs. The law expands the renewable fuel standard to require use of 36 billion gallons of renewable fuel by 2022. Given that ethanol is the most widely used renewable fuel in the U.S. market, ethanol will likely make up a significant portion of the 36-billion-gallon requirement. The vast majority of ethanol used in the United States is blended with gasoline to create E10-gasoline with up to 10% ethanol. The remaining ethanol is sold in the form of E85 - a gasoline blend with as much as 85% ethanol that can only be used in flexible-fuel vehicles (FFVs). Consumption of E85 is at present limited by both the size of the FFV fleet and the number of E85 fueling stations. Gasoline consumption in the United States is currently about 140 billion gallons per year; thus the maximum use of ethanol as E10 is only about 14 billion gallons. While the U.S. Department of Energy (DOE) remains committed to expanding the E85 infrastructure, that market represented less than 1% of the ethanol consumed in 2010 and will not be able to absorb projected volumes of ethanol in the near term. Because of these factors, DOE and others have been assessing the viability of using mid-level ethanol blends (E15 or E20) as a way to accommodate growing volumes of ethanol. The DOE Mid-Level Ethanol Blends Test Program has been under way since 2007, supported jointly by the Office of the Biomass Program and the Vehicle Technologies Program. One of the larger projects, the Catalyst Durability Study, or Vehicle Aging Study, will be completed early in calendar year 2011. The following report describes a subproject of the Vehicle Aging Study in which powertrain components from 18 of the vehicles were examined at Southwest Research Institute under contract to Oak Ridge National Laboratory (ORNL).

Role of testing in requalifying Transamerica Delaval, Inc., engines for nuclear service

International Nuclear Information System (INIS)

Nesbitt, J.F.; Dingee, D.A.; Laity, W.W.

1985-03-01

This paper discusses the role of testing in requalifying Transamerica Delaval, Inc. (TDI) diesel generators for use as emergency standby power sources at nuclear power plants. ''Lead'' engine tests (to confirm the design adequacy of key engine components under conditions that could induce high-cycle fatigue) and ''following'' engine tests (for engines of the same model and equipped with the same components as the ''lead'' engine) have been conducted at several nuclear power plants. The tests conducted by Duke Power Company (Catawba Nuclear Station Unit 1) and Long Island Lighting Company (Shoreham Nuclear Power Station Unit 1) are discussed. 2 refs

High-voltage engineering and testing

CERN Document Server

Ryan, Hugh M

2013-01-01

This 3rd edition of High Voltage Engineering Testing describes strategic developments in the field and reflects on how they can best be managed. All the key components of high voltage and distribution systems are covered including electric power networks, UHV and HV. Distribution systems including HVDC and power electronic systems are also considered.

40 CFR 1048.505 - How do I test engines using steady-state duty cycles, including ramped-modal testing?

Science.gov (United States)

2010-07-01

...-state duty cycles, including ramped-modal testing? 1048.505 Section 1048.505 Protection of Environment... SPARK-IGNITION ENGINES Test Procedures § 1048.505 How do I test engines using steady-state duty cycles... some cases, we allow you to choose the appropriate steady-state duty cycle for an engine. In these...

40 CFR 86.340-79 - Gasoline-fueled engine dynamometer test run.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 18 2010-07-01 2010-07-01 false Gasoline-fueled engine dynamometer... Emission Regulations for New Gasoline-Fueled and Diesel-Fueled Heavy-Duty Engines; Gaseous Exhaust Test Procedures § 86.340-79 Gasoline-fueled engine dynamometer test run. (a) This section applies to gasoline...

Selected Issues of the Indicating Measurements in a Spark Ignition Engine with an Additional Expansion Process

Directory of Open Access Journals (Sweden)

Marcin Noga

2017-03-01

Full Text Available The paper presents the results of research on the turbocharged spark ignition engine with additional exhaust expansion in a separate cylinder, which is commonly known as the five-stroke engine. The research engine has been constructed based on the four cylinder engine in which two outer cylinders work as the fired cylinders, while two internally connected inner cylinders constitute the volume of the additional expansion process. The engine represents a powertrain realizing an ultra-expansion cycle. The purpose of the study was to find an effective additional expansion process in the five-stroke engine. Cylinder-pressure indicating measurements were carried out for one of the fired cylinders and the additional expansion cylinder. The study was performed for over 20 different points on the engine operation map. This allowed us to determine a dependence between the pressure indicated in the fired cylinders and in the additional expansion cylinders. A function of the mean pressure indicated in the additional expansion cylinder versus a brake mean effective pressure was also presented. This showed a load threshold from which the work of the cylinders of additional expansion produced benefits for the output of the experimental engine. The issues of mechanical efficiency and effective efficiency of this engine were also discussed.

40 CFR 1045.301 - When must I test my production-line engines?

Science.gov (United States)

2010-07-01

... engines? 1045.301 Section 1045.301 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS Testing Production-line Engines § 1045.301 When must I test my production-line engines? (a) If you produce...

Action Memorandum for the Engineering Test Reactor under the Idaho Cleanup Project

Energy Technology Data Exchange (ETDEWEB)

A. B. Culp

2007-01-26

This Action Memorandum documents the selected alternative for decommissioning of the Engineering Test Reactor at the Idaho National Laboratory under the Idaho Cleanup Project. Since the missions of the Engineering Test Reactor Complex have been completed, an engineering evaluation/cost analysis that evaluated alternatives to accomplish the decommissioning of the Engineering Test Reactor Complex was prepared adn released for public comment. The scope of this Action Memorandum is to encompass the final end state of the Complex and disposal of the Engineering Test Reactor vessol. The selected removal action includes removing and disposing of the vessel at the Idaho CERCLA Disposal Facility and demolishing the reactor building to ground surface.

New engine method for biodiesel cetane number testing

Directory of Open Access Journals (Sweden)

Pešić Radivoje B.

2008-01-01

Full Text Available Substitution of fossil fuels with fuels that come from part renewable sources has been a subject of many studies and researches in the past decade. Considering the higher cost and limits of production resources, a special attention is focused on raising the energy efficiency of biofuel usage, mainly through optimization of the combustion process. Consequently, in biofuel applications, there is a need for determination of auto-ignition quality expressed by cetane number as a dominant characteristic that influences combustion parameters. The fact that the method for cetane number determination is comparative in nature has led us to try to develop substitute engine method for cetane number determination, by the use of the available laboratory equipment and serial, mono-cylinder engine with direct injection, DMB LDA 450. Description of the method, results of optimization of engine’s working parameters for conduction of the test and method’s Accuracy estimation are given in the paper. The paper also presents the results of domestic biodiesel fuels cetane number testing with the application of described engine method, developed at the Laboratory for internal combustion engines and fuels and lubricants of the Faculty of Mechanical Engineering from Kragujevac, Serbia.

F-1 Engine for Saturn V Undergoing a Static Test

Science.gov (United States)

1964-01-01

The flame and exhaust from the test firing of an F-1 engine blast out from the Saturn S-IB Static Test Stand in the east test area of the Marshall Space Flight Center. A Cluster of five F-1 engines, located in the S-IC (first) stage of the Saturn V vehicle, provided over 7,500,000 pounds of thrust to launch the giant rocket. The towering 363-foot Saturn V was a multistage, multiengine launch vehicle standing taller than the Statue of Liberty. Altogether, the Saturn V engines produced as much power as 85 Hoover Dams.

Characteristics, finite element analysis, test description, and preliminary test results of the STM4-120 kinematic Stirling engine

Science.gov (United States)

Linker, K. L.; Rawlinson, K. S.; Smith, G.

1991-10-01

The Department of Energy's Solar Thermal Program has, as one of its program elements, the development and evaluation of conversion device technologies applicable to dish-electric systems. The primary research and development combines a conversion device (heat engine), solar receiver, and generator mounted at the focus of a parabolic dish concentrator. The Stirling-cycle heat engine was identified as the conversion device for dish-electric with the most potential for meeting the program's goals for efficiency, reliability, and installed cost. To advance the technology toward commercialization, Sandia National Laboratories has acquired a Stirling Thermal Motors, Inc. kinematic Stirling engine, STM4-120, for evaluation. The engine is being bench-tested at Sandia's Engine Test Facility and will be combined later with a solar receiver for on-sun evaluation. This report presents the engine characteristics, finite element analyses of critical engine components, test system layout, instrumentation, and preliminary performance results from the bench test.

Digital Image Correlation Techniques Applied to Large Scale Rocket Engine Testing

Science.gov (United States)

Gradl, Paul R.

2016-01-01

Rocket engine hot-fire ground testing is necessary to understand component performance, reliability and engine system interactions during development. The J-2X upper stage engine completed a series of developmental hot-fire tests that derived performance of the engine and components, validated analytical models and provided the necessary data to identify where design changes, process improvements and technology development were needed. The J-2X development engines were heavily instrumented to provide the data necessary to support these activities which enabled the team to investigate any anomalies experienced during the test program. This paper describes the development of an optical digital image correlation technique to augment the data provided by traditional strain gauges which are prone to debonding at elevated temperatures and limited to localized measurements. The feasibility of this optical measurement system was demonstrated during full scale hot-fire testing of J-2X, during which a digital image correlation system, incorporating a pair of high speed cameras to measure three-dimensional, real-time displacements and strains was installed and operated under the extreme environments present on the test stand. The camera and facility setup, pre-test calibrations, data collection, hot-fire test data collection and post-test analysis and results are presented in this paper.

Sensitivity Analyses for Cross-Coupled Parameters in Automotive Powertrain Optimization

Directory of Open Access Journals (Sweden)

Pongpun Othaganont

2014-06-01

Full Text Available When vehicle manufacturers are developing new hybrid and electric vehicles, modeling and simulation are frequently used to predict the performance of the new vehicles from an early stage in the product lifecycle. Typically, models are used to predict the range, performance and energy consumption of their future planned production vehicle; they also allow the designer to optimize a vehicle’s configuration. Another use for the models is in performing sensitivity analysis, which helps us understand which parameters have the most influence on model predictions and real-world behaviors. There are various techniques for sensitivity analysis, some are numerical, but the greatest insights are obtained analytically with sensitivity defined in terms of partial derivatives. Existing methods in the literature give us a useful, quantified measure of parameter sensitivity, a first-order effect, but they do not consider second-order effects. Second-order effects could give us additional insights: for example, a first order analysis might tell us that a limiting factor is the efficiency of the vehicle’s prime-mover; our new second order analysis will tell us how quickly the efficiency of the powertrain will become of greater significance. In this paper, we develop a method based on formal optimization mathematics for rapid second-order sensitivity analyses and illustrate these through a case study on a C-segment electric vehicle.

Open modular architecture controls at GM Powertrain: technology and implementation

Science.gov (United States)

Bailo, Clark P.; Yen, C. J.

1997-01-01

General Motors Powertrain Group (GMPTG) has been the leader in implementing open, modular architecture controller (OMAC) technologies in its manufacturing applications since 1986. The interest in OMAC has been greatly expanded for the past two years because of the advancement of personal computer technologies and the publishing of the OMAC whitepaper by the US automotive companies stating the requirements of OMAC technologies in automotive applications. The purpose of this paper is to describe the current OMAC projects and the future direction of implementation at GMPTG. An overview of the OMAC project and the definition of the OMAC concept are described first. The rationale of pursuing open technologies is explained from the perspective of GMPTG in lieu of its agile manufacturing strategy. Examples of existing PC-based control applications are listed to demonstrate the extensive commitment to PC-based technologies that has already been put in place. A migration plan form PC-based to OMAC-based systems with the thorough approach of validation are presented next to convey the direction that GMPTG is taking in implementing OMAC technologies. Leveraged technology development projects are described to illustrate the philosophy and approaches toward the development of OMAC technologies at GMPTG. Finally, certain implementation issues are discussed to emphasize efforts that are still required to have successful implementations of OMAC systems.

Investigating the impact of in-vehicle transients on diesel soot emissions

Directory of Open Access Journals (Sweden)

Filipi Zoran

2008-01-01

Full Text Available This paper describes development of a test cell setup for concurrent running of a real engine and a simulation of the vehicle system, and its use for investigating highly-dynamic engine-in-vehicle operation and its effect on diesel engine emissions. Running an engine in the test cell under conditions experienced in the vehicle enables acquiring detailed insight into dynamic interactions between power train sub-systems, and the impact of it on fuel consumption and transient emissions. This type of data may otherwise be difficult and extremely costly to obtain from a vehicle prototype test. In particular, engine system response during critical transients and the effect of transient excursions on emissions are investigated using advanced, fast-response test instrumentation and emissions analyzers. Main enablers of the work include the highly dynamic AC electric dynamometer with the accompanying computerized control system and the computationally efficient simulation of the driveline/vehicle system. The latter is developed through systematic energy-based proper modeling that tailors the virtual model to capture critical powertrain transients while running in real time. Coupling the real engine with the virtual driveline/vehicle offers a chance to easily modify vehicle parameters, and even study different power train configurations. In particular, the paper describes the engine-in-the-loop study of a V-8, 6l engine coupled to a virtual 4´4 off road vehicle. This engine is considered as a high-performance option for this truck and the real prototype of the complete vehicle does not exist yet. The results shed light on critical transients in a conventional powertrain and their effect on NOx and soot emissions. Measurements demonstrate very large spikes of particulate concentration at the initiation of vehicle acceleration events. Characterization of transients and their effect on particulate emission provides a basis for devising engine-level or

Assessment by Simu ation of Benefits of New HEV Powertrain Configurations Évaluation par simulation des bénéfices de nouvelles chaînes de traction hybrides

Directory of Open Access Journals (Sweden)

Kim N.

2013-05-01

Full Text Available During the past couple of years, numerous powertrain configurations for Hybrid Electric Vehicles (HEV have been introduced into the marketplace. The current dominant architecture is the power-split configuration with the input split (single-mode from Toyota and Ford. General Motors (GM recently introduced a two-mode power-split configuration for applications in sport utility vehicles. Also, the first commercially available Plug-In Hybrid Electric Vehicle (PHEV — the GM Volt — was introduced into the market in 2010. The GM Volt uses a series-split powertrain architecture, which provides benefits over the series architecture, which typically has been considered for Electric-Range Extended Vehicles (E-REV. This paper assesses the benefits of these different powertrain architectures (single-mode versus multi-mode for HEV (series versus GM Voltec for PHEV by comparing component sizes, system efficiency and fuel consumption over several drive cycles. On the basis of dynamic models, a detailed component control algorithm was developed for each configuration. The powertrain components were sized to meet all-electric-range, performance and grade-capacity requirements. This paper presents and compares the impact of these different powertrain configurations on component size and fuel consumption. Durant les dernières années, de nombreuses configurations de motorisation pour véhicules hybrides ont été introduites sur le marché. La solution dominante est actuellement la dérivation de puissance en configuration ‘input split’ simple mode utilisée par Toyota et Ford. General Motors (GM a récemment introduit une configuration basée sur la dérivation de puissance avec deux modes pour application sur des SUV (Sport Utility Vehicle. Par ailleurs, le premier véhicule hybride rechargeable la Volt de GM a été introduite sur le marché en 2010. La Volt utilise une architecture qui autorise plusieurs modes : électrique, série et dérivation de

Quality engineering in FFTF irradiation tests

International Nuclear Information System (INIS)

Caplinger, W.H.

1980-01-01

The design and fabrication of an irradiation test for the Fast Flux Test Facility are planned, controlled and documented in accordance with the Department of Energy standards. Tests built by Westinghouse Hanford Company are further controlled and guided by a series of increasingly specific documents, including guidelines for program control, procedures for engineering operations, standard practices and detailed operating procedures. In response to this guidance, a series of five documents is prepared covering each step of the experiment from conception through fabrication and assembly. This paper describes the quality assurance accompanying these five steps

In situ vitrification engineering-scale test ES-INEL-5 test plan

International Nuclear Information System (INIS)

Stoots, P.R.

1990-06-01

In 1952, the Radioactive Waste Management Complex (RWMC) was established at the Idaho National Engineering Laboratory (INEL). RWMC is located on approximately 144 acres in the southwestern corner of the INEL site and was established as a controlled area for the burial of solid low-level wastes generated by INEL operations. In 1954, the 88-acre Subsurface Disposal Area (SDA) of RWMC began accepting solid transuranic-contaminated waste. From 1954 to 1970, transuranic-contaminated waste was accepted from the Rocky Flats Plant (RFP) near Golden, CO, as well as from other US Department of Energy (DOE) locations. In 1987, the Buried Waste Program (BWP) was established by EG ampersand G Idaho, Inc., the prime contractor at INEL. Following the Environmental Restoration guidelines of the Buried Waste Program, the In Situ Vitrification Program is participating in a Remedial Investigation/Feasibility Study (RI/FS) for permanent disposal of INEL waste, in compliance with the Comprehensive Environmental Response, Compensation, and Liability Act (CERCLA). This study was requested and is being funded by the Office of Technology Development of the Idaho Operations Office of DOE (DOE-ID). As part of the RI/FS, an in situ vitrification (ISV) scoping study on the treatability of mixed low-level and mixed transuranic-contaminated waste is being performed to determine applicability of ISV to remediation of waste at SDA. This In Situ Vitrification Engineering-Scale Test ES-INEL-5 Test Plan considers the data needs of engineering, regulatory, health, and safety activities for all sampling and analysis activities in support of engineering scale test ES-INEL-5. 5 refs., 3 figs., 4 tabs

Optimally Controlled Flexible Fuel Powertrain System

Energy Technology Data Exchange (ETDEWEB)

Hakan Yilmaz; Mark Christie; Anna Stefanopoulou

2010-12-31

The primary objective of this project was to develop a true Flex Fuel Vehicle capable of running on any blend of ethanol from 0 to 85% with reduced penalty in usable vehicle range. A research and development program, targeting 10% improvement in fuel economy using a direct injection (DI) turbocharged spark ignition engine was conducted. In this project a gasoline-optimized high-technology engine was considered and the hardware and configuration modifications were defined for the engine, fueling system, and air path. Combined with a novel engine control strategy, control software, and calibration this resulted in a highly efficient and clean FFV concept. It was also intended to develop robust detection schemes of the ethanol content in the fuel integrated with adaptive control algorithms for optimized turbocharged direct injection engine combustion. The approach relies heavily on software-based adaptation and optimization striving for minimal modifications to the gasoline-optimized engine hardware system. Our ultimate objective was to develop a compact control methodology that takes advantage of any ethanol-based fuel mixture and not compromise the engine performance under gasoline operation.

DEVELOPMENT AND TESTING OF A PRE-PROTOTYPE RAMGEN ENGINE

Energy Technology Data Exchange (ETDEWEB)

Aaron Koopman

2003-07-01

The research and development effort of a new kind of compressor and engine is presented. The superior performance of these two products arises from the superior performance of rotating supersonic shock-wave compression. Several tasks were performed in compliance with the DOE award objectives. A High Risk Technology review was conducted and evaluated by a team of 20 senior engineers and scientists representing various branches of the federal government. The conceptual design of a compression test rig, test rotors, and test cell adaptor was completed. The work conducted lays the foundation for the completed design and testing of the compression test rig, and the design of a supersonic shock-wave compressor matched to a conventional combustor and turbine.

40 CFR 86.1327-96 - Engine dynamometer test procedures; overview.

Science.gov (United States)

2010-07-01

... device, the exhaust pipe must be the same diameter as found in-use for at least 4 pipe diameters upstream... Exhaust Test Procedures § 86.1327-96 Engine dynamometer test procedures; overview. (a) The engine.... The exhaust emissions are diluted with ambient air and a continuous proportional sample is collected...

Speed Synchronization Control of Integrated Motor–Transmission Powertrain over CAN through Active Period-Scheduling Approach

Directory of Open Access Journals (Sweden)

Wanke Cao

2017-11-01

Full Text Available This paper deals with the speed synchronization control of integrated motor–transmission (IMT powertrain systems in pure electric vehicles (EVs over a controller area network (CAN subject to both network-induced delays and network congestion. A CAN has advantages over point-to-point communication; however, it imposes network-induced delays and network congestion into the control system, which can deteriorate the shifting quality and make system integration difficult. This paper presents a co-design scheme combining active period scheduling and discrete-time slip mode control (SMC to deal with both network-induced delays and network congestion of the CAN, which improves the speed synchronization control for high shifting quality and prevents network congestion for the system’s integration. The results of simulations and hardware-in-loop experiments show the effectiveness of the proposed scheme, which can ensure satisfactory speed synchronization performance while significantly reducing the network’s utilization.

Definition study of a Variable Cycle Experimental Engine (VCEE) and associated test program and test plan

Science.gov (United States)

Allan, R. D.

1978-01-01

The Definition Study of a Variable Cycle Experimental Engine (VCEE) and Associated Test Program and Test Plan, was initiated to identify the most cost effective program for a follow-on to the AST Test Bed Program. The VCEE Study defined various subscale VCE's based on different available core engine components, and a full scale VCEE utilizing current technology. The cycles were selected, preliminary design accomplished and program plans and engineering costs developed for several program options. In addition to the VCEE program plans and options, a limited effort was applied to identifying programs that could logically be accomplished on the AST Test Bed Program VCE to extend the usefulness of this test hardware. Component programs were provided that could be accomplished prior to the start of a VCEE program.

AJ26 rocket engine testing news briefing

Science.gov (United States)

2010-01-01

NASA's John C. Stennis Space Center Director Gene Goldman (center) stands in front of a 'pathfinder' rocket engine with Orbital Sciences Corp. President and Chief Operating Officer J.R. Thompson (left) and Aerojet President Scott Seymour during a Feb. 24 news briefing at the south Mississippi facility. The leaders appeared together to announce a partnership for testing Aerojet AJ26 rocket engines at Stennis. The engines will be used to power Orbital's Taurus II space vehicles to provide commercial cargo transportation missions to the International Space Station for NASA. During the event, the Stennis partnership with Orbital was cited as an example of the new direction of NASA to work with commercial interests for space travel and transport.

Performance Testing of Diesel Engine using Cardanol-Kerosene oil blend

Directory of Open Access Journals (Sweden)

Ravindra

2018-01-01

Full Text Available Awareness of environmental pollution and fossil fuel depletion has necessitated the use of biofuels in engines which have a relatively cleaner emissions. Cardanol is a biofuel, abundantly available in India, which is a by-product of cashew processing industries. In this study performance of raw Cardanol blended with kerosene has been tested in diesel engine. Volumetric blend BK30 (30% kerosene and 70% Cardanol has been used for the test. The properties like flash point, viscosity and calorific value of the blend have been determined. The test was carried out in four stroke diesel engine connected with an eddy current dynamometer. Performance of the engine has been analysed by finding the brake specific fuel consumption (BSFC and brake thermal efficiency (BTE. The results showed that the brake thermal efficiency of the blend is 29.87%, with less CO and smoke emission compared to diesel. The results were also compared with the performance of Cardanol diesel blend and Cardanol camphor oil blend, which were already tested in diesel engines by other researchers. Earlier research work reveals that the blend of 30% camphor oil and 70% Cardanol performs very closer to diesel fuel with a thermal efficiency of 29.1%. Similarly, higher brake thermal efficiency was obtained for 20% Cardanol and 80% diesel blend.

Modeling of hybrid vehicle fuel economy and fuel engine efficiency

Science.gov (United States)

Wu, Wei

"Near-CV" (i.e., near-conventional vehicle) hybrid vehicles, with an internal combustion engine, and a supplementary storage with low-weight, low-energy but high-power capacity, are analyzed. This design avoids the shortcoming of the "near-EV" and the "dual-mode" hybrid vehicles that need a large energy storage system (in terms of energy capacity and weight). The small storage is used to optimize engine energy management and can provide power when needed. The energy advantage of the "near-CV" design is to reduce reliance on the engine at low power, to enable regenerative braking, and to provide good performance with a small engine. The fuel consumption of internal combustion engines, which might be applied to hybrid vehicles, is analyzed by building simple analytical models that reflect the engines' energy loss characteristics. Both diesel and gasoline engines are modeled. The simple analytical models describe engine fuel consumption at any speed and load point by describing the engine's indicated efficiency and friction. The engine's indicated efficiency and heat loss are described in terms of several easy-to-obtain engine parameters, e.g., compression ratio, displacement, bore and stroke. Engine friction is described in terms of parameters obtained by fitting available fuel measurements on several diesel and spark-ignition engines. The engine models developed are shown to conform closely to experimental fuel consumption and motored friction data. A model of the energy use of "near-CV" hybrid vehicles with different storage mechanism is created, based on simple algebraic description of the components. With powertrain downsizing and hybridization, a "near-CV" hybrid vehicle can obtain a factor of approximately two in overall fuel efficiency (mpg) improvement, without considering reductions in the vehicle load.

Doublet III construction and engineering test

International Nuclear Information System (INIS)

Anon.

1979-01-01

Progress during FY-78 on the construction and operation of the Doublet III is reported. Detailed discussions about the installation and testing of various components and subsystems, including the B-coil, E-coil, F-coils and support structure, vacuum vessel, vacuum pumping system, limiter, thermal insulation blanket, control system, B-coil power system, E-coil power system, F-coil power system, and motor-generator, are presented. A brief review of the engineering test operation is given

Assessment of alternative fuel and powertrain transit bus options using real-world operations data: Life-cycle fuel and emissions modeling

International Nuclear Information System (INIS)

Xu, Yanzhi; Gbologah, Franklin E.; Lee, Dong-Yeon; Liu, Haobing; Rodgers, Michael O.; Guensler, Randall L.

2015-01-01

Highlights: • We present a practical fuel and emissions modeling tool for alternative fuel buses. • The model assesses well-to-wheels emissions impacts of bus fleet decisions. • Mode-based approach is used to account for duty cycles and local conditions. • A case study using real-world operations data from Atlanta, GA is presented. • Impacts of alternative bus options depend on operating and geographic features. - Abstract: Hybrid and electric powertrains and alternative fuels (e.g., compressed natural gas (CNG), biodiesel, or hydrogen) can often reduce energy consumption and emissions from transit bus operations relative to conventional diesel. However, the magnitude of these energy and emissions savings can vary significantly, due to local conditions and transit operating characteristics. This paper introduces the transit Fuel and Emissions Calculator (FEC), a mode-based life-cycle emissions modeling tool for transit bus and rail technologies that compares the performance of multiple alternative fuels and powertrains across a range of operational characteristics and conditions. The purpose of the FEC is to provide a practical, yet technically sophisticated tool for regulatory agencies and policy analysts in assessing transit fleet options. The FEC’s modal modeling approach estimates emissions as a function of engine load, which in turn is a function of transit service parameters, including duty cycle (idling and speed-acceleration profile), road grade, and passenger loading. This approach allows for customized assessments that account for local conditions. Direct emissions estimates are derived from the scaled tractive power (STP) operating mode bins and emissions factors employed in the U.S. EPA’s MOVES (MOtor Vehicle Emissions Simulator) model. Life-cycle emissions estimates are calculated using emissions factors from the GREET (Greenhouse Gases, Regulated Emissions, and Energy Use in Transportation) model. The case study presented in this paper

412th Test Engineering Group Vision for Future Knowledge Management (KM)

Science.gov (United States)

2018-05-17

Presentation 3. DATES COVERED (From - To) 17 May 2018 4. TITLE AND SUBTITLE 412th Test Engineering Group Vision for Future Knowledge Management (KM... Engineering Group 307 E. Popson Ave Edwards AFB, CA 93523 8. PERFORMING ORGANIZATION REPORT NUMBER 412TW-PA...centers for the TENG test customers to allow the data to be readily available within minutes of a flight, for the data to be organized so that the engineer

J-2 Engine ready to go into test stand

Science.gov (United States)

1965-01-01

Two technicians watch carefully as cables prepare to lift a J-2 engine into a test stand. The J-2 powered the second stage and the third stage of the Saturn V moon rocket. The towering 363-foot Saturn V was a multi-stage, multi-engine launch vehicle standing taller than the Statue of Liberty. Altogether, the Saturn V engines produced as much power as 85 Hoover Dams.

Lean mixture engine testing and evaluation program. [for automobile engine pollution and fuel performances

Science.gov (United States)

Dowdy, M. W.; Hoehn, F. W.; Griffin, D. C.

1975-01-01

Experimental results for fuel consumption and emissions are presented for a 350 CID (5.7 liter) Chevrolet V-8 engine modified for lean operation with gasoline. The lean burn engine achieved peak thermal efficiency at an equivalence ratio of 0.75 and a spark advance of 60 deg BTDC. At this condition the lean burn engine demonstrated a 10% reduction in brake specific fuel consumption compared with the stock engine; however, NOx and hydrocarbon emissions were higher. With the use of spark retard and/or slightly lower equivalence ratios, the NOx emissions performance of the stock engine was matched while showing a 6% reduction in brake specific fuel consumption. Hydrocarbon emissions exceeded the stock values in all cases. Diagnostic data indicate that lean performance in the engine configuration tested is limited by ignition delay, cycle-to-cycle pressure variations, and cylinder-to-cylinder distribution.

Emission control of hybrid vehicles. What are the resulting requirements?; Abgasnachbehandlung bei Hybridfahrzeugen. Welche Anforderungen ergeben sich daraus?

Energy Technology Data Exchange (ETDEWEB)

Spurk, Paul; Mueller, Wilfried [Umicore AG und Co.KG, Hanau (Germany); Beidl, Christian; Weickgenannt, Philipp [TU Darmstadt (Germany); Hohenberg, Guenter [IVD Prof. Hohenberg, Darmstadt (Germany)

2010-07-01

In hybrid powertrain systems the operation of the combustion engine is changed in comparison to an internal combustion or IC engine - only systems. This causes new boundary conditions and challenges for an optimized design of the exhaust aftertreatment system. These specific behavior characteristics have been identified based on results measured with a Toyota Prius III test vehicle on a both chassis dynamometer and road cycle evaluation. NEDC cycle results show a characteristic reduction of catalyst temperature compared to a conventional powertrain as the combustion engine is switched on for only approx. 40% of the cycle time. A further challenge can be identified in hybrid specific events, e.g. when the restart of the engine follows a short standstill period, resulting in high engine out emissions which need to be properly converted by the catalyst. It can also be clearly recognized that the state of charge of the traction battery has significant impact on the emission behavior. Furthermore the highly interesting question about the influence of plug-in hybrid systems with extended periods of electric-only driving needs to be addressed. A test sequence with simulated plug-in operation in which the combustion engine is only active in the EUDC part of the cycle shows the expected reduction of CO{sub 2} - emission but an increase in engine out NOx - emission. An important aspect is given by the cooling behavior of the exhaust system during the engine shut-off time. Detailed knowledge of this behavior is key for generating efficient operating strategies without emission deterioration. ''Real world'' load profiles are required for this task and are derived from the Darmstadt Urban and Extra Urban Cycle road tests. The test vehicle with series application and fresh catalytic converters is safely below the Euro V emission limits under all circumstances. Thus a certain potential can be seen for reducing the precious metal loading with a corresponding

Impact of uniform electrode current distribution on ETF. [Engineering Test Facility MHD generator

Science.gov (United States)

Bents, D. J.

1982-01-01

A basic reason for the complexity and sheer volume of electrode consolidation hardware in the MHD ETF Powertrain system is the channel electrode current distribution, which is non-uniform. If the channel design is altered to provide uniform electrode current distribution, the amount of hardware required decreases considerably, but at the possible expense of degraded channel performance. This paper explains the design impacts on the ETF electrode consolidation network associated with uniform channel electrode current distribution, and presents the alternate consolidation designs which occur. They are compared to the baseline (non-uniform current) design with respect to performance, and hardware requirements. A rational basis is presented for comparing the requirements for the different designs and the savings that result from uniform current distribution. Performance and cost impacts upon the combined cycle plant are discussed.

Present status of high temperature engineering test and research, 1994

International Nuclear Information System (INIS)

1994-10-01

High temperature gas-cooled reactors have excellent features such as the generation of high temperature close to 1000degC, very high inherent safety and high fuel burnup. By the advanced basic research under high temperature irradiation condition, the creation of various new technologies which become the momentum of future technical innovation can be expected. The construction of the high temperature engineering test reactor (HTTR) was decided in 1987, which aims at the thermal output of 30 MW and the coolant temperature at reactor exit of 950degC. The initial criticality is scheduled in 1998. Japan Atomic Energy Research Institute has advanced the high temperature engineering test and research, and plans the safety verifying test of the HTTR, the test of connecting heat utilization plants and so on. In this report, mainly the results obtained for one year from May, 1993 are summarized. The outline of the high temperature engineering test and development of the HTTR technologies are reported. (K.I.)

Engineer Research and Development Center's Materials Testing Center (MTC)

Data.gov (United States)

Federal Laboratory Consortium — The Engineer Research and Development Center's Materials Testing Center (MTC) is committed to quality testing and inspection services that are delivered on time and...

40 CFR 86.341-79 - Diesel engine dynamometer test run.

Science.gov (United States)

2010-07-01

...-fueled engines are covered in § 86.340. (b) The temperature of the air supplied to the engine shall be... engine at rated speed and maximum horsepower until the oil and water temperatures are stabilized. The... segments. (4) A leak check is permitted between test segments. (5) A hang-up check is permitted between...

Applying the design-build-test paradigm in microbiome engineering.

Science.gov (United States)

Pham, Hoang Long; Ho, Chun Loong; Wong, Adison; Lee, Yung Seng; Chang, Matthew Wook

2017-12-01

The recently discovered roles of human microbiome in health and diseases have inspired research efforts across many disciplines to engineer microbiome for health benefits. In this review, we highlight recent progress in human microbiome research and how modifications to the microbiome could result in implications to human health. Furthermore, we discuss the application of a 'design-build-test' framework to expedite microbiome engineering efforts by reviewing current literature on three key aspects: design principles to engineer the human microbiome, methods to engineer microbiome with desired functions, and analytical techniques to examine complex microbiome samples. Copyright © 2017 Elsevier Ltd. All rights reserved.

40 CFR 86.1337-96 - Engine dynamometer test run.

Science.gov (United States)

2010-07-01

.... Plug the canister port that is normally connected to the fuel tank. (ii) Prepare the engine... test should be performed. (2) Connect evacuated sample collection bags to the dilute exhaust and... turned off, turn off the engine cooling fan(s) if used, and the CVS blower (or disconnect the exhaust...

Solar Thermal Upper Stage Cryogen System Engineering Checkout Test

Science.gov (United States)

Olsen, A. D; Cady, E. C.; Jenkins, D. S.

1999-01-01

The Solar Thermal Upper Stage technology (STUSTD) program is a solar thermal propulsion technology program cooperatively sponsored by a Boeing led team and by NASA MSFC. A key element of its technology program is development of a liquid hydrogen (LH2) storage and supply system which employs multi-layer insulation, liquid acquisition devices, active and passive thermodynamic vent systems, and variable 40W tank heaters to reliably provide near constant pressure H2 to a solar thermal engine in the low-gravity of space operation. The LH2 storage and supply system is designed to operate as a passive, pressure fed supply system at a constant pressure of about 45 psia. During operation of the solar thermal engine over a small portion of the orbit the LH2 storage and supply system propulsively vents through the enjoy at a controlled flowrate. During the long coast portion of the orbit, the LH2 tank is locked up (unvented). Thus, all of the vented H2 flow is used in the engine for thrust and none is wastefully vented overboard. The key to managing the tank pressure and therefore the H2 flow to the engine is to manage and balance the energy flow into the LH2 tank with the MLI and tank heaters with the energy flow out of the LH2 tank through the vented H2 flow. A moderate scale (71 cu ft) LH2 storage and supply system was installed and insulated at the NASA MSFC Test Area 300. The operation of the system is described in this paper. The test program for the LH2 system consisted of two parts: 1) a series of engineering tests to characterize the performance of the various components in the system: and 2) a 30-day simulation of a complete LEO and GEO transfer mission. This paper describes the results of the engineering tests, and correlates these results with analytical models used to design future advanced Solar Orbit Transfer Vehicles.

Engine testing of ceramic cam-roller followers

Energy Technology Data Exchange (ETDEWEB)

Kalish, Y. (Detroit Diesel Corp., MI (United States))

1992-04-01

For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

Development of a test and flight engineering oriented language, phase 3

Science.gov (United States)

Kamsler, W. F.; Case, C. W.; Kinney, E. L.; Gyure, J.

1970-01-01

Based on an analysis of previously developed test oriented languages and a study of test language requirements, a high order language was designed to enable test and flight engineers to checkout and operate the proposed space shuttle and other NASA vehicles and experiments. The language is called ALOFT (a language oriented to flight engineering and testing). The language is described, its terminology is compared to similar terms in other test languages, and its features and utilization are discussed. The appendix provides the specifications for ALOFT.

The development of a Flight Test Engineer's Workstation for the Automated Flight Test Management System

Science.gov (United States)

Tartt, David M.; Hewett, Marle D.; Duke, Eugene L.; Cooper, James A.; Brumbaugh, Randal W.

1989-01-01

The Automated Flight Test Management System (ATMS) is being developed as part of the NASA Aircraft Automation Program. This program focuses on the application of interdisciplinary state-of-the-art technology in artificial intelligence, control theory, and systems methodology to problems of operating and flight testing high-performance aircraft. The development of a Flight Test Engineer's Workstation (FTEWS) is presented, with a detailed description of the system, technical details, and future planned developments. The goal of the FTEWS is to provide flight test engineers and project officers with an automated computer environment for planning, scheduling, and performing flight test programs. The FTEWS system is an outgrowth of the development of ATMS and is an implementation of a component of ATMS on SUN workstations.

Simultaneous Optimization of Topology and Component Sizes for Double Planetary Gear Hybrid Powertrains

Directory of Open Access Journals (Sweden)

Weichao Zhuang

2016-05-01

Full Text Available Hybrid powertrain technologies are successful in the passenger car market and have been actively developed in recent years. Optimal topology selection, component sizing, and controls are required for competitive hybrid vehicles, as multiple goals must be considered simultaneously: fuel efficiency, emissions, performance, and cost. Most of the previous studies explored these three design dimensions separately. In this paper, two novel frameworks combining these three design dimensions together are presented and compared. One approach is nested optimization which searches through the whole design space exhaustively. The second approach is called enhanced iterative optimization, which executes the topology optimization and component sizing alternately. A case study shows that the later method can converge to the global optimal design generated from the nested optimization, and is much more computationally efficient. In addition, we also address a known issue of optimal designs: their sensitivity to parameters, such as varying vehicle weight, which is a concern especially for the design of hybrid buses. Therefore, the iterative optimization process is applied to design a robust multi-mode hybrid electric bus under different loading scenarios as the final design challenge of this paper.

Single Common Powertrain Lubricant (SCPL) Development. Part 2

Science.gov (United States)

2014-04-01

Lubricant (SCPL), General Engine Products (GEP) 6.5L(T), Detroit Diesel Corporation ( DDC ) 6V53T, High Temperature Oil Endurance, MIL-PRF-46167, MIL-PRF...using the Detroit Diesel Corporation ( DDC ) 6V53T, American Society for Testing and Materials (ASTM) D5966 roller follower wear protection...candidates. A Detroit Diesel Corporation ( DDC ) 6V53T, from the M113A3 Armored Personnel Carrier (APC), was used to evaluate the two revised candidates and a

The California greenhouse gas initiative and its implications to the automotive industry

Energy Technology Data Exchange (ETDEWEB)

Smith, B. C.; Miller, R. T.; Center for Automotive Research

2006-05-31

CAR undertook this investigation to better understand the costs and challenges of a local (state) regulation necessitating the implementation of alternative or advanced powertrain technology. CAR will attempt to add insight into the challenges that local regulations present to the automotive industry, and to contribute further to the discussion of how advanced powertrain technology may be used to meet such regulation. Any local law that (directly or indirectly) affects light duty motor vehicle fuel economy creates what in effect is a specialty market for powertrain technology. As such these small markets present significant challenges for automotive manufacturers. First, a small market with unique standards presents significant challenges to an industry that has sustained growth by relying on large volumes to achieve scale economies and deliver products at a cost acceptable to the consumer. Further, the challenges of the additional technology make it likely that any powertrain capable of meeting the stringent emissions standards will include costly additional components, and thus will be more costly to manufacture. It is likely that manufacturers would consider the following actions as steps to deliver products to meet the pending California regulatory requirements anticipated as a result of prior California legislation: (1) Substituting more fuel efficient vehicles: Bring in more efficient vehicles from global operations, while likely dropping existing domestic products. (2) Substituting powertrains: Add existing downsized engines (i.e. turbocharged versions, etc.) into California market-bound vehicles. (3) Powertrain enhancements: Add technology to current engine and transmission offerings to improve efficiency and reduce emissions. (4) Incorporating alternative powertrains into existing vehicle platforms: Develop a hybrid or other type of powertrain for an existing vehicle. (5) New powertrains and new platforms: Develop vehicles specifically intended to

The Design and Testing of a Miniature Turbofan Engine

Science.gov (United States)

Cosentino, Gary B.; Murray, James E.

2009-01-01

Off-the-shelf jet propulsion in the 50 - 500 lb thrust class sparse. A true twin-spool turbofan in this range does not exist. Adapting an off-the-shelf turboshaft engine is feasible. However the approx.10 Hp SPT5 can t quite make 50 lbs. of thrust. Packaging and integration is challenging, especially the exhaust. Building on our engine using a 25 Hp turboshaft seems promising if the engine becomes available. Test techniques used, though low cost, adequate for the purpose.

Modeling and fuzzy control of the engine coolant conditioning system in an IC engine test bed

International Nuclear Information System (INIS)

Mohtasebi, Seyed Saeid; Shirazi, Farzad A.; Javaheri, Ahmad; Nava, Ghodrat Hamze

2010-01-01

Mechanical and thermodynamical performance of internal combustion engines is significantly affected by the engine working temperature. In an engine test bed, the internal combustion engines are tested in different operating conditions using a dynamometer. It is required that the engine temperature be controlled precisely, particularly in transient states. This precise control can be achieved by an engine coolant conditioning system mainly consisting of a heat exchanger, a control valve, and a controller. In this study, constitutive equations of the system are derived first. These differential equations show the second- order nonlinear time-varying dynamics of the system. The model is validated with the experimental data providing satisfactory results. After presenting the dynamic equations of the system, a fuzzy controller is designed based on our prior knowledge of the system. The fuzzy rules and the membership functions are derived by a trial and error and heuristic method. Because of the nonlinear nature of the system the fuzzy rules are set to satisfy the requirements of the temperature control for different operating conditions of the engine. The performance of the fuzzy controller is compared with a PI one for different transient conditions. The results of the simulation show the better performance of the fuzzy controller. The main advantages of the fuzzy controller are the shorter settling time, smaller overshoot, and improved performance especially in the transient states of the system

Test/QA plan for the verification testing of selective catalytic reduction control technologies for highway, nonroad use heavy-duty diesel engines

Science.gov (United States)

This ETV test/QA plan for heavy-duty diesel engine testing at the Southwest Research Institute’s Department of Emissions Research (DER) describes how the Federal Test Procedure (FTP), as listed in 40 CFR Part 86 for highway engines and 40 CFR Part 89 for nonroad engines, will be ...

Regulated Emissions from Biodiesel Tested in Heavy-Duty Engines Meeting 2004 Emission Standards

Energy Technology Data Exchange (ETDEWEB)

McCormick, R. L.; Tennant, C. J.; Hayes, R. R.; Black, S.; Ireland, J.; McDaniel, T.; Williams, A.; Frailey, M.; Sharp, C. A.

2005-11-01

Biodiesel produced from soybean oil, canola oil, yellow grease, and beef tallow was tested in two heavy-duty engines. The biodiesels were tested neat and as 20% by volume blends with a 15 ppm sulfur petroleum-derived diesel fuel. The test engines were the following: 2002 Cummins ISB and 2003 DDC Series 60. Both engines met the 2004 U.S. emission standard of 2.5 g/bhp-h NO{sub x}+HC (3.35 g/kW-h) and utilized exhaust gas recirculation (EGR). All emission tests employed the heavy-duty transient procedure as specified in the U.S. Code of Federal Regulations. Reduction in PM emissions and increase in NO{sub x} emissions were observed for all biodiesels in all engines, confirming observations made in older engines. On average PM was reduced by 25% and NO{sub x} increased by 3% for the two engines tested for a variety of B20 blends. These changes are slightly larger in magnitude, but in the same range as observed in older engines. The cetane improver 2-ethyl hexyl nitrate was shown to have no measurable effect on NO{sub x} emissions from B20 in these engines, in contrast to observations reported for older engines. The effect of intake air humidity on NO{sub x} emissions from the Cummins ISB was quantified. The CFR NO{sub x}/humidity correction factor was shown to be valid for an engine equipped with EGR, operating at 1700 m above sea level, and operating on conventional or biodiesel.

40 CFR 1045.305 - How must I prepare and test my production-line engines?

Science.gov (United States)

2010-07-01

... production-line engines? 1045.305 Section 1045.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM SPARK-IGNITION PROPULSION MARINE ENGINES AND VESSELS Testing Production-line Engines § 1045.305 How must I prepare and test my production-line engines...

40 CFR 1048.305 - How must I prepare and test my production-line engines?

Science.gov (United States)

2010-07-01

... production-line engines? 1048.305 Section 1048.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Testing Production-line Engines § 1048.305 How must I prepare and test my production-line engines? This...

40 CFR 1051.301 - When must I test my production-line vehicles or engines?

Science.gov (United States)

2010-07-01

... vehicles or engines? 1051.301 Section 1051.301 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.301 When must I test my production-line vehicles or engines? (a...

Optical Methods For Automatic Rating Of Engine Test Components

Science.gov (United States)

Pritchard, James R.; Moss, Brian C.

1989-03-01

In recent years, increasing commercial and legislative pressure on automotive engine manufacturers, including increased oil drain intervals, cleaner exhaust emissions and high specific power outputs, have led to increasing demands on lubricating oil performance. Lubricant performance is defined by bench engine tests run under closely controlled conditions. After test, engines are dismantled and the parts rated for wear and accumulation of deposit. This rating must be consistently carried out in laboratories throughout the world in order to ensure lubricant quality meeting the specified standards. To this end, rating technicians evaluate components, following closely defined procedures. This process is time consuming, inaccurate and subject to drift, requiring regular recalibration of raters by means of international rating workshops. This paper describes two instruments for automatic rating of engine parts. The first uses a laser to determine the degree of polishing of the engine cylinder bore, caused by the reciprocating action of piston. This instrument has been developed to prototype stage by the NDT Centre at Harwell under contract to Exxon Chemical, and is planned for production within the next twelve months. The second instrument uses red and green filtered light to determine the type, quality and position of deposit formed on the piston surfaces. The latter device has undergone feasibility study, but no prototype exists.

Action Memorandum for Decommissioning the Engineering Test Reactor Complex under the Idaho Cleanup Project

International Nuclear Information System (INIS)

A. B. Culp

2007-01-01

This Action Memorandum documents the selected alternative for decommissioning of the Engineering Test Reactor at the Idaho National Laboratory under the Idaho Cleanup Project. Since the missions of the Engineering Test Reactor Complex have been completed, an engineering evaluation/cost analysis that evaluated alternatives to accomplish the decommissioning of the Engineering Test Reactor Complex was prepared and released for public comment. The scope of this Action Memorandum is to encompass the final end state of the Complex and disposal of the Engineering Test Reactor vessel. The selected removal action includes removing and disposing of the vessel at the Idaho CERCLA Disposal Facility and demolishing the reactor building to ground surface

Enabling Fast Charging: A Technology Gap Assessment

Energy Technology Data Exchange (ETDEWEB)

None, None

2017-10-31

Decreasing energy consumption across the U.S. transportation sector, especially in commercial light-duty vehicles, is essential for the United States to gain energy independence. Recently, powertrain electrification with plug-in electric vehicles (PEVs) have gained traction as an alternative due to their inherent efficiency advantages compared to the traditional internal combustion engine vehicle (ICEV). Even though there are many different classes of PEVs, the intent of this study is to focus on non-hybrid powertrains, or battery electric vehicles (BEVs).

Analysis and test of insulated components for rotary engine

Science.gov (United States)

Badgley, Patrick R.; Doup, Douglas; Kamo, Roy

1989-01-01

The direct-injection stratified-charge (DISC) rotary engine, while attractive for aviation applications due to its light weight, multifuel capability, and potentially low fuel consumption, has until now required a bulky and heavy liquid-cooling system. NASA-Lewis has undertaken the development of a cooling system-obviating, thermodynamically superior adiabatic rotary engine employing state-of-the-art thermal barrier coatings to thermally insulate engine components. The thermal barrier coating material for the cast aluminum, stainless steel, and ductile cast iron components was plasma-sprayed zirconia. DISC engine tests indicate effective thermal barrier-based heat loss reduction, but call for superior coefficient-of-thermal-expansion matching of materials and better tribological properties in the coatings used.

Advanced electric powertrain technology: ADEPT platform overview

NARCIS (Netherlands)

Stipetic, S.; Miebach, W.; Wilkins, S.; Lomonova, E.A.; Paulides, J.J.H.; Tegenbosch, J.

2016-01-01

Design of high performance, low cost and clean propulsion systems requires multiple disciplines such as physics, mathematics, electrical engineering, mechanical engineering and specialisms like control engineering and safety. This paper details the program of EU FP7 Multi-ITN project ADvanced

Planning for Plume Diagnostics for Ground Testing of J-2X Engines at the SSC

Science.gov (United States)

SaintCyr, William W.; Tejwani, Gopal D.; McVay, Gregory P.; Langford, Lester A.; SaintCyr, William W.

2010-01-01

John C. Stennis Space Center (SSC) is the premier test facility for liquid rocket engine development and certification for the National Aeronautics and Space Administration (NASA). Therefore, it is no surprise that the SSC will play the most prominent role in the engine development testing and certification for the J-2X engine. The Pratt & Whitney Rocketdyne J-2X engine has been selected by the Constellation Program to power the Ares I Upper Stage Element and the Ares V Earth Departure Stage in NASA s strategy of risk mitigation for hardware development by building on the Apollo program and other lessons learned to deliver a human-rated engine that is on an aggressive development schedule, with first demonstration flight in 2010 and human test flights in 2012. Accordingly, J-2X engine design, development, test, and evaluation is to build upon heritage hardware and apply valuable experience gained from past development and testing efforts. In order to leverage SSC s successful and innovative expertise in the plume diagnostics for the space shuttle main engine (SSME) health monitoring,1-10 this paper will present a blueprint for plume diagnostics for various proposed ground testing activities for J-2X at SSC. Complete description of the SSC s test facilities, supporting infrastructure, and test facilities is available in Ref. 11. The A-1 Test Stand is currently being prepared for testing the J-2X engine at sea level conditions. The A-2 Test Stand is currently being used for testing the SSME and may also be used for testing the J-2X engine at sea level conditions in the future. Very recently, ground-breaking ceremony for the new A-3 rocket engine test stand took place at SSC on August 23, 2007. A-3 is the first large - scale test stand to be built at the SSC since the A and B stands were constructed in the 1960s. The A-3 Test Stand will be used for testing J-2X engines under vacuum conditions simulating high altitude operation at approximately 30,480 m (100,000 ft

Conceptual studies of plasma engineering test facility

International Nuclear Information System (INIS)

Hiraoka, Toru; Tazima, Teruhiko; Sugihara, Masayoshi; Kasai, Masao; Shinya, Kichiro

1979-04-01

Conceptual studies have been made of a Plasma Engineering Test Facility, which is to be constructed following JT-60 prior to the experimental power reactor. The physical aim of this machine is to examine self-ignition conditions. This machine possesses all essential technologies for reactor plasma, i.e. superconducting magnet, remote maintenance, shielding, blanket test modules, tritium handling. Emphasis in the conceptual studies was on structural consistency of the machine and whether the machine would be constructed practically. (author)

Preliminary engineering specifications for a test demonstration multilayer protective barrier cover system

International Nuclear Information System (INIS)

Phillips, S.J.; Gilbert, T.W.; Adams, M.R.

1985-03-01

This report presents preliminary engineering specifications for a test protective barrier cover system and support radiohydrology facility to be constructed at the Hanford Protective Barrier Test Facility (PBTF). Construction of this test barrier and related radiohydrology facility is part of a continuing effort to provide construction experience and performance evaluation of alternative barrier designs used for long-term isolation of disposed radioactive waste materials. Design specifications given in this report are tentative, based on interim engineering and computer simulation design efforts. Final definitive design specifications and engineering prints will be produced in FY 1986. 6 refs., 10 figs., 1 tab

Engineering Abstractions in Model Checking and Testing

DEFF Research Database (Denmark)

Achenbach, Michael; Ostermann, Klaus

2009-01-01

Abstractions are used in model checking to tackle problems like state space explosion or modeling of IO. The application of these abstractions in real software development processes, however, lacks engineering support. This is one reason why model checking is not widely used in practice yet...... and testing is still state of the art in falsification. We show how user-defined abstractions can be integrated into a Java PathFinder setting with tools like AspectJ or Javassist and discuss implications of remaining weaknesses of these tools. We believe that a principled engineering approach to designing...... and implementing abstractions will improve the applicability of model checking in practice....

Self Diagnostic Accelerometer Ground Testing on a C-17 Aircraft Engine

Science.gov (United States)

Tokars, Roger P.; Lekki, John D.

2013-01-01

The self diagnostic accelerometer (SDA) developed by the NASA Glenn Research Center was tested for the first time in an aircraft engine environment as part of the Vehicle Integrated Propulsion Research (VIPR) program. The VIPR program includes testing multiple critical flight sensor technologies. One such sensor, the accelerometer, measures vibrations to detect faults in the engine. In order to rely upon the accelerometer, the health of the accelerometer must be ensured. Sensor system malfunction is a significant contributor to propulsion in flight shutdowns (IFSD) which can lead to aircraft accidents when the issue is compounded with an inappropriate crew response. The development of the SDA is important for both reducing the IFSD rate, and hence reducing the rate at which this component failure type can put an aircraft in jeopardy, and also as a critical enabling technology for future automated malfunction diagnostic systems. The SDA is a sensor system designed to actively determine the accelerometer structural health and attachment condition, in addition to making vibration measurements. The SDA uses a signal conditioning unit that sends an electrical chirp to the accelerometer and recognizes changes in the response due to changes in the accelerometer health and attachment condition. In an effort toward demonstrating the SDAs flight worthiness and robustness, multiple SDAs were mounted and tested on a C-17 aircraft engine. The engine test conditions varied from engine off, to idle, to maximum power. The two SDA attachment conditions used were fully tight and loose. The newly developed SDA health algorithm described herein uses cross correlation pattern recognition to discriminate a healthy from a faulty SDA. The VIPR test results demonstrate for the first time the robustness of the SDA in an engine environment characterized by high vibration levels.

HISTORICAL AMERICAN ENGINEERING RECORD - IDAHO NATIONAL ENGINEERING AND ENVIRONMENTAL LABORATORY, TEST AREA NORTH, HAER NO. ID-33-E

Energy Technology Data Exchange (ETDEWEB)

Susan Stacy; Hollie K. Gilbert

2005-02-01

Test Area North (TAN) was a site of the Aircraft Nuclear Propulsion (ANP) Project of the U.S. Air Force and the Atomic Energy Commission. Its Cold War mission was to develop a turbojet bomber propelled by nuclear power. The project was part of an arms race. Test activities took place in five areas at TAN. The Assembly & Maintenance area was a shop and hot cell complex. Nuclear tests ran at the Initial Engine Test area. Low-power test reactors operated at a third cluster. The fourth area was for Administration. A Flight Engine Test facility (hangar) was built to house the anticipated nuclear-powered aircraft. Experiments between 1955-1961 proved that a nuclear reactor could power a jet engine, but President John F. Kennedy canceled the project in March 1961. ANP facilities were adapted for new reactor projects, the most important of which were Loss of Fluid Tests (LOFT), part of an international safety program for commercial power reactors. Other projects included NASA's Systems for Nuclear Auxiliary Power and storage of Three Mile Island meltdown debris. National missions for TAN in reactor research and safety research have expired; demolition of historic TAN buildings is underway.

HISTORICAL AMERICAN ENGINEERING RECORD - IDAHO NATIONAL ENGINEERING AND ENVIRONMENTAL LABORATORY, TEST AREA NORTH, HAER NO. ID-33-E

International Nuclear Information System (INIS)

Susan Stacy; Hollie K. Gilbert

2005-01-01

Test Area North (TAN) was a site of the Aircraft Nuclear Propulsion (ANP) Project of the U.S. Air Force and the Atomic Energy Commission. Its Cold War mission was to develop a turbojet bomber propelled by nuclear power. The project was part of an arms race. Test activities took place in five areas at TAN. The Assembly and Maintenance area was a shop and hot cell complex. Nuclear tests ran at the Initial Engine Test area. Low-power test reactors operated at a third cluster. The fourth area was for Administration. A Flight Engine Test facility (hangar) was built to house the anticipated nuclear-powered aircraft. Experiments between 1955-1961 proved that a nuclear reactor could power a jet engine, but President John F. Kennedy canceled the project in March 1961. ANP facilities were adapted for new reactor projects, the most important of which were Loss of Fluid Tests (LOFT), part of an international safety program for commercial power reactors. Other projects included NASA's Systems for Nuclear Auxiliary Power and storage of Three Mile Island meltdown debris. National missions for TAN in reactor research and safety research have expired; demolition of historic TAN buildings is underway

Preliminary Results From a Heavily Instrumented Engine Ice Crystal Icing Test in a Ground Based Altitude Test Facility

Science.gov (United States)

Flegel, Ashlie B.; Oliver, Michael J.

2016-01-01

Preliminary results from the heavily instrumented ALF502R-5 engine test conducted in the NASA Glenn Research Center Propulsion Systems Laboratory are discussed. The effects of ice crystal icing on a full scale engine is examined and documented. This same model engine, serial number LF01, was used during the inaugural icing test in the Propulsion Systems Laboratory facility. The uncommanded reduction of thrust (rollback) events experienced by this engine in flight were simulated in the facility. Limited instrumentation was used to detect icing on the LF01 engine. Metal temperatures on the exit guide vanes and outer shroud and the load measurement were the only indicators of ice formation. The current study features a similar engine, serial number LF11, which is instrumented to characterize the cloud entering the engine, detect/characterize ice accretion, and visualize the ice accretion in the region of interest. Data were acquired at key LF01 test points and additional points that explored: icing threshold regions, low altitude, high altitude, spinner heat effects, and the influence of varying the facility and engine parameters. For each condition of interest, data were obtained from some selected variations of ice particle median volumetric diameter, total water content, fan speed, and ambient temperature. For several cases the NASA in-house engine icing risk assessment code was used to find conditions that would lead to a rollback event. This study further helped NASA develop necessary icing diagnostic instrumentation, expand the capabilities of the Propulsion Systems Laboratory, and generate a dataset that will be used to develop and validate in-house icing prediction and risk mitigation computational tools. The ice accretion on the outer shroud region was acquired by internal video cameras. The heavily instrumented engine showed good repeatability of icing responses when compared to the key LF01 test points and during day-to-day operation. Other noticeable

Development of a non-engine fuel injector deposit test for alternative fuels (ENIAK-project)

Energy Technology Data Exchange (ETDEWEB)

Hoffmann, Hajo; Pohland vom Schloss, Heide [OWI - Oel Waerme Institut GmbH, Herzogenrath (Germany)

2013-06-01

Deposit formation in and on the injectors of diesel engines may lead to injector malfunction, resulting in a loss in power, rough engine operation and poor emission levels. Poor Biodiesel quality, contamination with copper and zinc as well as undesired reactions between (several) additives and biodiesel components are known causes for nozzle fouling. Therefore, good housekeeping when using biodiesel is required, and all additives have to pass a no-harm test concerning injector fouling. The standard fouling tests are two engine tests: The XUD9-test (CEC F-23-01) and the DW-10-test (CEC DF 98-08). The XUD9 is a cost efficient, fast and proven testing method. It uses, however, an obsolete indirect injection diesel engine and cannot reproduce internal diesel injector deposits (IDID). The newer DW10 test is complex, costly and designed for high stress. This reduces the engine life and leads to a fuel consumption of approximately 1,000 1 per test, both contributing to the high costs of the test. The ENIAK-Project is funded by the FNR (''Fachagentur Nachwachsende Rohstoffe'', Agency for Renewable Resources) and conducted in cooperation with AGQM, ASG and ERC. Its main goal is the development, assembly, commissioning, and evaluation of a non-engine fuel injector test. It uses a complete common rail system. The injection takes place in a self-designed reactor instead of an engine, and the fuel is not combusted, but re-condensed and pumped in a circle, leading to a low amount of fuel required. If the test method proves to be as reliable as expected, it can be used as an alternative test method for injector fouling with low requirements regarding infrastructure on the testing site and sample volume. (orig.)

Palm oil as a fuel for agricultural diesel engines: Comparative testing against diesel oil

Directory of Open Access Journals (Sweden)

Teerawat Apichato

2003-05-01

Full Text Available Due to unstable oil price situation in the world market, many countries have been looking for alternative energy sources to substitute for petroleum. Vegetable oil is one of the alternatives which can be used as fuel in automotive engines either in the form of straight vegetable oil, or in the form of ethyl or methyl ester. This paper presents a comparative performance testing of diesel engine using diesel oil and refined palm oil over 2,000 hours of continuous running time. Short-term performance testing was conducted for each fuel on the dynamometer engine test bed. Specific fuel consumption, exhaust temperature and black smoke density were determined and measured. Long-term performance testing (or endurance test was also done by running the engines coupled with a generator in order to supply load (electricity to a lightbulb board. For each 500 hours of engine run time, the engines were dissembled for engine wear inspection. It was found that the fuel pump and fuel valve weight losses from both engines showed insignificant differences either at the first 500 hours of running time or at the second 500 hours of running time but the inlet valve from the engine fueled by diesel oil had a higher weight loss than the engine fueled by refined palm oil at the first 500 hours and at the second 500 hours of running time. The compression rings from the engine fueled by refined palm oil showed a significant weight loss compared to the engine fueled by diesel oil both after 500 hours and after 1000 hours of running time.

Ground test facilities for evaluating nuclear thermal propulsion engines and fuel elements

International Nuclear Information System (INIS)

Allen, G.C.; Beck, D.F.; Harmon, C.D.; Shipers, L.R.

1992-01-01

Interagency panels evaluating nuclear thermal propulsion development options have consistently recognized the need for constructing a major new ground test facility to support fuel element and engine testing. This paper summarizes the requirements, configuration, and design issues of a proposed ground test complex for evaluating nuclear thermal propulsion engines and fuel elements being developed for the Space Nuclear Thermal Propulsion (SNTP) program. 2 refs

Assessment of the quality of test results from selected civil engineering material testing laboratories in Tanzania

CSIR Research Space (South Africa)

Mbawala, SJ

2017-12-01

Full Text Available Civil and geotechnical engineering material testing laboratories are expected to produce accurate and reliable test results. However, the ability of laboratories to produce accurate and reliable test results depends on many factors, among others...

Potential Errors and Test Assessment in Software Product Line Engineering

Directory of Open Access Journals (Sweden)

Hartmut Lackner

2015-04-01

Full Text Available Software product lines (SPL are a method for the development of variant-rich software systems. Compared to non-variable systems, testing SPLs is extensive due to an increasingly amount of possible products. Different approaches exist for testing SPLs, but there is less research for assessing the quality of these tests by means of error detection capability. Such test assessment is based on error injection into correct version of the system under test. However to our knowledge, potential errors in SPL engineering have never been systematically identified before. This article presents an overview over existing paradigms for specifying software product lines and the errors that can occur during the respective specification processes. For assessment of test quality, we leverage mutation testing techniques to SPL engineering and implement the identified errors as mutation operators. This allows us to run existing tests against defective products for the purpose of test assessment. From the results, we draw conclusions about the error-proneness of the surveyed SPL design paradigms and how quality of SPL tests can be improved.

Utilization of fission reactors for fusion engineering testing

International Nuclear Information System (INIS)

Deis, G.A.; Miller, L.G.

1985-01-01

Fission reactors can be used to conduct some of the fusion nuclear engineering tests identified in the FINESSE study. To further define the advantages and disadvantages of fission testing, the technical and programmatic constraints on this type of testing are discussed here. This paper presents and discusses eight key issues affecting fission utilization. Quantitative comparisons with projected fusion operation are made to determine the technical assets and limitations of fission testing. Capabilities of existing fission reactors are summarized and compared with technical needs. Conclusions are then presented on the areas where fission testing can be most useful

Radiological effluents released from nuclear rocket and ramjet engine tests at the Nevada Test Site 1959 through 1969: Fact Book

Energy Technology Data Exchange (ETDEWEB)

Friesen, H.N.

1995-06-01

Nuclear rocket and ramjet engine tests were conducted on the Nevada Test Site (NTS) in Area 25 and Area 26, about 80 miles northwest of Las Vegas, Nevada, from July 1959 through September 1969. This document presents a brief history of the nuclear rocket engine tests, information on the off-site radiological monitoring, and descriptions of the tests.

Mechanical testing of hydrogels in cartilage tissue engineering: beyond the compressive modulus.

Science.gov (United States)

Xiao, Yinghua; Friis, Elizabeth A; Gehrke, Stevin H; Detamore, Michael S

2013-10-01

Injuries to articular cartilage result in significant pain to patients and high medical costs. Unfortunately, cartilage repair strategies have been notoriously unreliable and/or complex. Biomaterial-based tissue-engineering strategies offer great promise, including the use of hydrogels to regenerate articular cartilage. Mechanical integrity is arguably the most important functional outcome of engineered cartilage, although mechanical testing of hydrogel-based constructs to date has focused primarily on deformation rather than failure properties. In addition to deformation testing, as the field of cartilage tissue engineering matures, this community will benefit from the addition of mechanical failure testing to outcome analyses, given the crucial clinical importance of the success of engineered constructs. However, there is a tremendous disparity in the methods used to evaluate mechanical failure of hydrogels and articular cartilage. In an effort to bridge the gap in mechanical testing methods of articular cartilage and hydrogels in cartilage regeneration, this review classifies the different toughness measurements for each. The urgency for identifying the common ground between these two disparate fields is high, as mechanical failure is ready to stand alongside stiffness as a functional design requirement. In comparing toughness measurement methods between hydrogels and cartilage, we recommend that the best option for evaluating mechanical failure of hydrogel-based constructs for cartilage tissue engineering may be tensile testing based on the single edge notch test, in part because specimen preparation is more straightforward and a related American Society for Testing and Materials (ASTM) standard can be adopted in a fracture mechanics context.

40 CFR 1051.501 - What procedures must I use to test my vehicles or engines?

Science.gov (United States)

2010-07-01

... vehicles or engines? 1051.501 Section 1051.501 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Test Procedures § 1051.501 What procedures must I use to test my vehicles or engines? This section describes test...

Vehicle electrification. Quo vadis?

Energy Technology Data Exchange (ETDEWEB)

Brinkman, N. [GM Global Research and Development, Warren, MI (United States); Eberle, U.; Formanski, V.; Grebe, U.D.; Matthe, R. [General Motors Europe, Ruesselsheim (Germany)

2012-11-01

This publication describes the development of electrified propulsion systems from the invention of the automobile to the present and then provides an outlook on expected technology progress. Vehicle application areas for the various systems are identified based on a range of energy supply chains and the technological limits of electric powertrain components. GM anticipates that vehicle electrification will increase in the future. Battery-electric vehicles will become competitive for some applications, especially intra-urban, short-distance driving. Range-extended electric vehicles provide longer driving range and offer full capability; with this technology, electric vehicles can serve as the prime vehicle for many customers. Hydrogen-powered fuel cell-electric powertrains have potential for application across most of the vehicle segments. They produce zero emissions during all phases of operation, offer short refueling times, but have powertrain cooling and hydrogen storage packaging constraints. While the market share of electrified vehicles is expected to increase significantly, GM expects conventional powertrains with internal combustion engines to also have a long future - however, a lot of them will be supported by various levels of electrification. (orig.)

The laboratory test rig with miniature jet engine to research aviation fuels combustion process

Directory of Open Access Journals (Sweden)

Gawron Bartosz

2015-12-01

Full Text Available This article presents laboratory test rig with a miniature turbojet engine (MiniJETRig – Miniature Jet Engine Test Rig, that was built in the Air Force Institute of Technology. The test rig has been developed for research and development works aimed at modelling and investigating processes and phenomena occurring in full scale jet engines. In the article construction of a test rig is described, with a brief discussion on the functionality of each of its main components. Additionally examples of measurement results obtained during the realization of the initial tests have been included, presenting the capabilities of the test rig.

Mechanisms Engineering Test Loop - Phase 1 Status Report

Energy Technology Data Exchange (ETDEWEB)

Kultgen, D. [Argonne National Lab. (ANL), Argonne, IL (United States); Grandy, C. [Argonne National Lab. (ANL), Argonne, IL (United States); Hvasta, M. [Argonne National Lab. (ANL), Argonne, IL (United States); Lisowski, D. [Argonne National Lab. (ANL), Argonne, IL (United States); Toter, W. [Argonne National Lab. (ANL), Argonne, IL (United States); Borowski, A. [Argonne National Lab. (ANL), Argonne, IL (United States)

2016-09-01

This report documents the current status of the Mechanisms Engineering Test Loop (METL) as of the end of FY2016. Currently, METL is in Phase I of its design and construction. Once operational, the METL facility will test small to intermediate-scale components and systems in order to develop advanced liquid metal technologies. Testing different components in METL is essential for the future of advanced fast reactors as it will provide invaluable performance data and reduce the risk of failures during plant operation.

40 CFR 1048.410 - How must I select, prepare, and test my in-use engines?

Science.gov (United States)

2010-07-01

... my in-use engines? 1048.410 Section 1048.410 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Testing In-use Engines § 1048.410 How must I select, prepare, and test my in-use engines? (a) You...

Design and study of Engineering Test Facility - Helium Circulator

International Nuclear Information System (INIS)

Jiang Huijing; Ye Ping; Zhao Gang; Geng Yinan; Wang Jie

2015-01-01

Helium circulator is one of the key equipment of High-temperature Gas-cooled Reactor Pebble-bed Module (HTR-PM). In order to simulate most normal and accident operating conditions of helium circulator in HTR-PM, a full scale, rated flow rate and power, engineering test loop, which was called Engineering Test Facility - Helium Circulator (ETF-HC), was designed and established. Two prototypes of helium circulator, which was supported by Active Magnetic Bearing (AMB) or sealed by dry gas seals, would be tested on ETF-HC. Therefore, special interchangeable design was under consideration. ETF-HC was constructed compactly, which consisted of eleven sub-systems. In order to reduce the flow resistance of the circuit, special ducts, elbows, valves and flowmeters were selected. Two stages of heat exchange loops were designed and a helium - high pressure pure water heat exchanger was applied to ensure water wouldn't be vaporized while simulating accident conditions. Commissioning tests were carried out and operation results showed that ETF-HC meets the requirement of helium circulator operation. On this test facility, different kinds of experiments were supposed to be held, including mechanical and aerodynamic performance tests, durability tests and so on. These tests would provide the features and performance of helium circulator and verify its feasibility, availability and reliability. (author)

Testing and Development of a Shrouded Gas Turbine Engine in a Freejet Facility

National Research Council Canada - National Science Library

Garcia, Hector

2000-01-01

.... The combined cycle engine (CCE) could be incorporated into a variety of applications. The building of a new freejet facility and engine test rig at the Naval Postgraduate School enabled dynamic testing of the ongoing development of a turboramjet...

Design and Implementation of the Control System of an Internal Combustion Engine Test Unit

Directory of Open Access Journals (Sweden)

Tufan Koç

2014-02-01

Full Text Available Accurate tests and performance analysis of engines are required to minimize measurement errors and so the use of the advanced test equipment is imperative. In other words, the reliable test results depend on the measurement of many parameters and recording the experimental data accurately which is depended on engine test unit. This study aims to design the control system of an internal combustion engine test unit. In the study, the performance parameters of an available internal combustion engine have been transferred to computer in real time. A data acquisition (DAQ card has been used to transfer the experimental data to the computer. Also, a user interface has been developed for performing the necessary procedures by using LabVIEW. The dynamometer load, the fuel consumption, and the desired speed can easily be adjusted precisely by using DAQ card and the user interface during the engine test. Load, fuel consumption, and temperature values (the engine inlet-outlet, exhaust inlet-outlet, oil, and environment can be seen on the interface and also these values can be recorded to the computer. It is expected that developed system will contribute both to the education of students and to the researchers’ studies and so it will eliminate a major lack.

Stennis Holds Last Planned Space Shuttle Engine Test

Science.gov (United States)

2009-01-01

With 520 seconds of shake, rattle and roar on July 29, 2009 NASA's John C. Stennis Space Center marked the end of an era for testing the space shuttle main engines that have powered the nation's Space Shuttle Program for nearly three decades.

Public views evening engine test of a Space Shuttle Main Engine

Science.gov (United States)

2001-01-01

Over the past year, more than 20,000 people came to Stennis Space Center to witness the 'shake, rattle and roar' of one of the world's most sophisticated engines. Stennis Space Center in south Mississippi is NASA's lead center for rocket propulsion testing. StenniSphere, the visitor center for Stennis Space Center, hosted more than 250,000 visitors in its first year of operation. Of those visitors, 26.4 percent were from Louisiana.

Distributed Rocket Engine Testing Health Monitoring System, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The on-ground and Distributed Rocket Engine Testing Health Monitoring System (DiRETHMS) provides a system architecture and software tools for performing diagnostics...

Distributed Rocket Engine Testing Health Monitoring System, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Leveraging the Phase I achievements of the Distributed Rocket Engine Testing Health Monitoring System (DiRETHMS) including its software toolsets and system building...

Single-Cylinder Diesel Engine Tests with Unstabilized Water-in-Fuel Emulsions

Science.gov (United States)

1978-08-01

A single-cylinder, four-stroke cycle diesel engine was operated on unstabilized water-in-fuel emulsions. Two prototype devices were used to produce the emulsions on-line with the engine. More than 350 test points were run with baseline diesel fuel an...

The development and testing of ceramic components in piston engines. Final report

Energy Technology Data Exchange (ETDEWEB)

McEntire, B.J. [Norton Co., Northboro, MA (United States). Advanced Ceramics Div.; Willis, R.W.; Southam, R.E. [TRW, Inc., Cleveland, OH (United States)

1994-10-01

Within the past 10--15 years, ceramic hardware has been fabricated and tested in a number of piston engine applications including valves, piston pins, roller followers, tappet shims, and other wear components. It has been shown that, with proper design and installation, ceramics improve performance, fuel economy, and wear and corrosion resistance. These results have been obtained using rig and road tests on both stock and race engines. Selected summaries of these tests are presented in this review paper.

14 CFR 23.934 - Turbojet and turbofan engine thrust reverser systems tests.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Turbojet and turbofan engine thrust... CATEGORY AIRPLANES Powerplant General § 23.934 Turbojet and turbofan engine thrust reverser systems tests. Thrust reverser systems of turbojet or turbofan engines must meet the requirements of § 33.97 of this...

Initial closed operation of the CELSS Test Facility Engineering Development Unit

Science.gov (United States)

Kliss, M.; Blackwell, C.; Zografos, A.; Drews, M.; MacElroy, R.; McKenna, R.; Heyenga, A. G.

2003-01-01

As part of the NASA Advanced Life Support Flight Program, a Controlled Ecological Life Support System (CELSS) Test Facility Engineering Development Unit has been constructed and is undergoing initial operational testing at NASA Ames Research Center. The Engineering Development Unit (EDU) is a tightly closed, stringently controlled, ground-based testbed which provides a broad range of environmental conditions under which a variety of CELSS higher plant crops can be grown. Although the EDU was developed primarily to provide near-term engineering data and a realistic determination of the subsystem and system requirements necessary for the fabrication of a comparable flight unit, the EDU has also provided a means to evaluate plant crop productivity and physiology under controlled conditions. This paper describes the initial closed operational testing of the EDU, with emphasis on the hardware performance capabilities. Measured performance data during a 28-day closed operation period are compared with the specified functional requirements, and an example of inferring crop growth parameters from the test data is presented. Plans for future science and technology testing are also discussed. Published by Elsevier Science Ltd on behalf of COSPAR.

Advanced Materials Test Methods for Improved Life Prediction of Turbine Engine Components

National Research Council Canada - National Science Library

Stubbs, Jack

2000-01-01

Phase I final report developed under SBIR contract for Topic # AF00-149, "Durability of Turbine Engine Materials/Advanced Material Test Methods for Improved Use Prediction of Turbine Engine Components...

Alternate Material Pallet, 40" x 48", MIL-STD-1660, Engineering Evaluation Tests

National Research Council Canada - National Science Library

Dugan, Jeffery

2003-01-01

The U.S. Army Defense Ammunition Center (DAC), Validation Engineering Division (SJMAC-DEV) conducted Engineering Evaluation Tests to determine if the Alternate Material Pallet manufactured by Hunter Paine Enterprise, Inc...

A Decoupled Control of 5-Legs PWM Inverter Feeding a two Induction Motors-based Electric Vehicle Powertrain

Directory of Open Access Journals (Sweden)

Bekheïra Tabbache

2016-06-01

Full Text Available This paper proposes a traction drive system for electric vehicles (EVs with two separate induction motor drive-based wheels. In this context, two three-phase induction motors are associated to five legs power inverter which one leg is shared by two phases of the motors. The independent control of the two induction motors allows replacing the mechanical differential speeds by an equivalent electrical module called electric differential (ED. In the proposed EV powertrain based on 5-leg inverter, the challenge is to achieve a decoupled control of the induction motors to ensure the EV stability while cornering or under slippery road condition. For this, the proposed independent control uses Indirect Field Oriented Control to ensure speed and rotor flux control of each induction motor , a Pulse Width Modulation to provide the command sequences to the 5-leg inverter and electric differential to generate the an appropriate reference when the two induction motors should be controlled at different speeds. For this, a numerical implementation of the independent controls on an embedded board (TMS 320F2812 to ensure a separate control of induction motor fed by the 5-leg inverter. Moreover, the proposed control takes into account the EV context such as the EV dynamic and uses European and American normalized driving cycles. EV-specific experimental tests on a digital signal processor TMS320LF2812 are carried-out to show the effectiveness of the proposed independent control for ED in terms of robustness and stability.

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant. Conceptual Design Engineering Report (CDER). Volume 4: Supplementary engineering data

Science.gov (United States)

1981-01-01

The reference conceptual design of the Magnetohydrodynamic Engineering Test Facility (ETF), a prototype 200 MWe coal-fired electric generating plant designed to demonstrate the commercial feasibility of open cycle MHD is summarized. Main elements of the design are identified and explained, and the rationale behind them is reviewed. Major systems and plant facilities are listed and discussed. Construction cost and schedule estimates, and identification of engineering issues that should be reexamined are also given. The latest (1980-1981) information from the MHD technology program are integrated with the elements of a conventional steam power electric generating plant. Supplementary Engineering Data (Issues, Background, Performance Assurance Plan, Design Details, System Design Descriptions and Related Drawings) is presented.

Flight Tests of a Remaining Flying Time Prediction System for Small Electric Aircraft in the Presence of Faults

Science.gov (United States)

Hogge, Edward F.; Kulkarni, Chetan S.; Vazquez, Sixto L.; Smalling, Kyle M.; Strom, Thomas H.; Hill, Boyd L.; Quach, Cuong C.

2017-01-01

This paper addresses the problem of building trust in the online prediction of a battery powered aircraft's remaining flying time. A series of flight tests is described that make use of a small electric powered unmanned aerial vehicle (eUAV) to verify the performance of the remaining flying time prediction algorithm. The estimate of remaining flying time is used to activate an alarm when the predicted remaining time is two minutes. This notifies the pilot to transition to the landing phase of the flight. A second alarm is activated when the battery charge falls below a specified limit threshold. This threshold is the point at which the battery energy reserve would no longer safely support two repeated aborted landing attempts. During the test series, the motor system is operated with the same predefined timed airspeed profile for each test. To test the robustness of the prediction, half of the tests were performed with, and half were performed without, a simulated powertrain fault. The pilot remotely engages a resistor bank at a specified time during the test flight to simulate a partial powertrain fault. The flying time prediction system is agnostic of the pilot's activation of the fault and must adapt to the vehicle's state. The time at which the limit threshold on battery charge is reached is then used to measure the accuracy of the remaining flying time predictions. Accuracy requirements for the alarms are considered and the results discussed.

Preliminary results on performance testing of a turbocharged rotary combustion engine

Science.gov (United States)

Meng, P. R.; Rice, W. J.; Schock, H. J.; Pringle, D. P.

1982-01-01

The performance of a turbocharged rotary engine at power levels above 75 kW (100 hp) was studied. A twin rotor turbocharged Mazda engine was tested at speeds of 3000 to 6000 rpm and boost pressures to 7 psi. The NASA developed combustion diagnostic instrumentation was used to quantify indicated and pumping mean effect pressures, peak pressure, and face to face variability on a cycle by cycle basis. Results of this testing showed that a 5900 rpm a 36 percent increase in power was obtained by operating the engine in the turbocharged configuration. When operating with lean carburetor jets at 105 hp (78.3 kW) and 4000 rpm, a brake specific fuel consumption of 0.45 lbm/lb-hr was measured.

Demonstration of Air-Power-Assist Engine Technology for Clean Combustion and Direct Energy Recovery in Heavy Duty Application

Energy Technology Data Exchange (ETDEWEB)

Hyungsuk Kang; Chun Tai

2010-05-01

The first phase of the project consists of four months of applied research, starting from September 1, 2005 and was completed by December 31, 2005. During this time, the project team heavily relied on highly detailed numerical modeling techniques to evaluate the feasibility of the APA technology. Specifically, (i) A GT-Power{sup TM}engine simulation model was constructed to predict engine efficiency at various operating conditions. Efficiency was defined based on the second-law thermodynamic availability. (ii) The engine efficiency map generated by the engine simulation was then fed into a simplified vehicle model, which was constructed in the Matlab/Simulink environment, to predict fuel consumption of a refuse truck on a simple collection cycle. (iii) Design and analysis work supporting the concept of retrofitting an existing Sturman Industries Hydraulic Valve Actuation (HVA) system with the modifications that are required to run the HVA system with Air Power Assist functionality. A Matlab/Simulink model was used to calculate the dynamic response of the HVA system. Computer aided design (CAD) was done in Solidworks for mechanical design and hydraulic layout. At the end of Phase I, 11% fuel economy improvement was predicted. During Phase II, the engine simulation group completed the engine mapping work. The air handling group made substantial progress in identifying suppliers and conducting 3D modelling design. Sturman Industries completed design modification of the HVA system, which was reviewed and accepted by Volvo Powertrain. In Phase II, the possibility of 15% fuel economy improvement was shown with new EGR cooler design by reducing EGR cooler outlet temperature with APA engine technology from Air Handling Group. In addition, Vehicle Simulation with APA technology estimated 4 -21% fuel economy improvement over a wide range of driving cycles. During Phase III, the engine experimental setup was initiated at VPTNA, Hagerstown, MD. Air Handling system and HVA

A Systems Engineering Approach to Quality Assurance for Aerospace Testing

Science.gov (United States)

Shepherd, Christena C.

2015-01-01

On the surface, it appears that AS91001 has little to say about how to apply a Quality Management System (QMS) to major aerospace test programs (or even smaller ones). It also appears that there is little in the quality engineering Body of Knowledge (BOK)2 that applies to testing, unless it is nondestructive examination (NDE), or some type of lab or bench testing associated with the manufacturing process. However, if one examines: a) how the systems engineering (SE) processes are implemented throughout a test program; and b) how these SE processes can be mapped to the requirements of AS9100, a number of areas for involvement of the quality professional are revealed. What often happens is that quality assurance during a test program is limited to inspections of the test article; what could be considered a manufacturing al fresco approach. This limits the quality professional and is a disservice to the programs and projects, since there are a number of ways that quality can enhance critical processes, and support efforts to improve risk reduction, efficiency and effectiveness.

40 CFR 1048.401 - What testing requirements apply to my engines that have gone into service?

Science.gov (United States)

2010-07-01

... engines that have gone into service? 1048.401 Section 1048.401 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW, LARGE NONROAD SPARK-IGNITION ENGINES Testing In-use Engines § 1048.401 What testing requirements apply to my engines that have...

Predicting Energy Consumption for Potential Effective Use in Hybrid Vehicle Powertrain Management Using Driver Prediction

Science.gov (United States)

Magnuson, Brian

A proof-of-concept software-in-the-loop study is performed to assess the accuracy of predicted net and charge-gaining energy consumption for potential effective use in optimizing powertrain management of hybrid vehicles. With promising results of improving fuel efficiency of a thermostatic control strategy for a series, plug-ing, hybrid-electric vehicle by 8.24%, the route and speed prediction machine learning algorithms are redesigned and implemented for real- world testing in a stand-alone C++ code-base to ingest map data, learn and predict driver habits, and store driver data for fast startup and shutdown of the controller or computer used to execute the compiled algorithm. Speed prediction is performed using a multi-layer, multi-input, multi- output neural network using feed-forward prediction and gradient descent through back- propagation training. Route prediction utilizes a Hidden Markov Model with a recurrent forward algorithm for prediction and multi-dimensional hash maps to store state and state distribution constraining associations between atomic road segments and end destinations. Predicted energy is calculated using the predicted time-series speed and elevation profile over the predicted route and the road-load equation. Testing of the code-base is performed over a known road network spanning 24x35 blocks on the south hill of Spokane, Washington. A large set of training routes are traversed once to add randomness to the route prediction algorithm, and a subset of the training routes, testing routes, are traversed to assess the accuracy of the net and charge-gaining predicted energy consumption. Each test route is traveled a random number of times with varying speed conditions from traffic and pedestrians to add randomness to speed prediction. Prediction data is stored and analyzed in a post process Matlab script. The aggregated results and analysis of all traversals of all test routes reflect the performance of the Driver Prediction algorithm. The

Electric powertrain modeling of a fuel cell hybrid electric vehicle and development of a power distribution algorithm based on driving mode recognition

Energy Technology Data Exchange (ETDEWEB)

Ryu, Junghwan; Park, Yeongseop; Sunwoo, Myoungho [Hanyang University, 17 Haengdang-dong, Seongdong-gu, Seoul 133-791 (Korea)

2010-09-01

This paper proposes a novel fuzzy controller based on an adaptive membership function for optimum power management of a fuel cell hybrid electric vehicle (FCHEV). In the first phase, an electric powertrain model of the FCHEV is derived and a fuzzy controller is proposed. Then, the fuzzy controller is optimized using a genetic algorithm. The optimization process is accomplished through simulation for a given driving cycle. Since, however, the optimized result may vary according to the applied driving cycle for optimization, it is impossible for one optimized result to cover various driving cycles. In the second phase, an adaptive membership function based on a stochastic approach is proposed to guarantee optimum performance from the presented fuzzy controller, even though the driving cycle changes. This controller is referred to as the 'Stochastic fuzzy controller' (SFC) in this study. The SFC employs a stochastic approach where membership functions can be transformed statistically using a probability evaluated from driving pattern recognition. Then, driving cycle analysis is performed through off-line simulation and hardware in a loop simulation (HILS) test for four driving cycles. Finally, the SFC shows the best performance in terms of minimum fuel consumption and state-of-charge (SoC) maintenance. (author)

A Hydrogen Containment Process for Nuclear Thermal Engine Ground testing

Science.gov (United States)

Wang, Ten-See; Stewart, Eric; Canabal, Francisco

2016-01-01

The objective of this study is to propose a new total hydrogen containment process to enable the testing required for NTP engine development. This H2 removal process comprises of two unit operations: an oxygen-rich burner and a shell-and-tube type of heat exchanger. This new process is demonstrated by simulation of the steady state operation of the engine firing at nominal conditions.

R and D needs assessment for the Engineering Test Facility

International Nuclear Information System (INIS)

1980-10-01

The Engineering Test Facility (ETF), planned to be the next major US magnetic fusion device, has its mission (1) to provide the capability for moving into the engineering phase of fusion development and (2) to provide a test-bed for reactor components in a fusion environment. The design, construction, and operation of the ETF requires an increasing emphasis on certain key research and development (R and D) programs in magnetic fusion in order to provide the necessary facility design base. This report identifies these needs and discusses the apparent inadequacies of the presently planned US program to meet them, commensurate with the ETF schedule

Human factors evaluation of the engineering test reactor control room

International Nuclear Information System (INIS)

Banks, W.W.; Boone, M.P.

1981-03-01

The Reactor and Process Control Rooms at the Engineering Test Reactor were evaluated by a team of human factors engineers using available human factors design criteria. During the evaluation, ETR, equipment and facilities were compared with MIL-STD-1472-B, Human Engineering design Criteria for Military Systems. The focus of recommendations centered on: (a) displays and controls; placing displays and controls in functional groups; (b) establishing a consistent color coding (in compliance with a standard if possible); (c) systematizing annunciator alarms and reducing their number; (d) organizing equipment in functional groups; and (e) modifying labeling and lines of demarcation

Durability Testing of Biomass Based Oxygenated Fuel Components in a Compression Ignition Engine

Energy Technology Data Exchange (ETDEWEB)

Ratcliff, Matthew A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); McCormick, Robert L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Baumgardner, Marc E. [Gonzaga University; Lakshminarayanan, Arunachalam [Colorado State University; Olsen, Daniel B. [Colorado State University; Marchese, Anthony J. [Colorado State University

2017-10-18

Blending cellulosic biofuels with traditional petroleum-derived fuels results in transportation fuels with reduced carbon footprints. Many cellulosic fuels rely on processing methods that produce mixtures of oxygenates which must be upgraded before blending with traditional fuels. Complete oxygenate removal is energy-intensive and it is likely that such biofuel blends will necessarily contain some oxygen content to be economically viable. Previous work by our group indicated that diesel fuel blends with low levels (<4%-vol) of oxygenates resulted in minimal negative effects on short-term engine performance and emissions. However, little is known about the long-term effects of these compounds on engine durability issues such as the impact on fuel injection, in-cylinder carbon buildup, and engine oil degradation. In this study, four of the oxygenated components previously tested were blended at 4%-vol in diesel fuel and tested with a durability protocol devised for this work consisting of 200 hrs of testing in a stationary, single-cylinder, Yanmar diesel engine operating at constant load. Oil samples, injector spray patterns, and carbon buildup from the injector and cylinder surfaces were analyzed. It was found that, at the levels tested, these fuels had minimal impact on the overall engine operation, which is consistent with our previous findings.

A robust H∞ control-based hierarchical mode transition control system for plug-in hybrid electric vehicle

Science.gov (United States)

Yang, Chao; Jiao, Xiaohong; Li, Liang; Zhang, Yuanbo; Chen, Zheng

2018-01-01

To realize a fast and smooth operating mode transition process from electric driving mode to engine-on driving mode, this paper presents a novel robust hierarchical mode transition control method for a plug-in hybrid electric bus (PHEB) with pre-transmission parallel hybrid powertrain. Firstly, the mode transition process is divided into five stages to clearly describe the powertrain dynamics. Based on the dynamics models of powertrain and clutch actuating mechanism, a hierarchical control structure including two robust H∞ controllers in both upper layer and lower layer is proposed. In upper layer, the demand clutch torque can be calculated by a robust H∞controller considering the clutch engaging time and the vehicle jerk. While in lower layer a robust tracking controller with L2-gain is designed to perform the accurate position tracking control, especially when the parameters uncertainties and external disturbance occur in the clutch actuating mechanism. Simulation and hardware-in-the-loop (HIL) test are carried out in a traditional driving condition of PHEB. Results show that the proposed hierarchical control approach can obtain the good control performance: mode transition time is greatly reduced with the acceptable jerk. Meanwhile, the designed control system shows the obvious robustness with the uncertain parameters and disturbance. Therefore, the proposed approach may offer a theoretical reference for the actual vehicle controller.

Free-piston Stirling engine/linear alternator 1000-hour endurance test

Science.gov (United States)

Rauch, J.; Dochat, G.

1985-01-01

The Free Piston Stirling Engine (FPSE) has the potential to be a long lived, highly reliable, power conversion device attractive for many product applications such as space, residential or remote site power. The purpose of endurance testing the FPSE was to demonstrate its potential for long life. The endurance program was directed at obtaining 1000 operational hours under various test conditions: low power, full stroke, duty cycle and stop/start. Critical performance parameters were measured to note any change and/or trend. Inspections were conducted to measure and compare critical seal/bearing clearances. The engine performed well throughout the program, completing more than 1100 hours. Hardware inspection, including the critical clearances, showed no significant change in hardware or clearance dimensions. The performance parameters did not exhibit any increasing or decreasing trends. The test program confirms the potential for long life FPSE applications.

Engineering test facility design definition

Science.gov (United States)

Bercaw, R. W.; Seikel, G. R.

1980-01-01

The Engineering Test Facility (ETF) is the major focus of the Department of Energy (DOE) Magnetohydrodynamics (MHD) Program to facilitate commercialization and to demonstrate the commercial operability of MHD/steam electric power. The ETF will be a fully integrated commercial prototype MHD power plant with a nominal output of 200 MW sub e. Performance of this plant is expected to meet or surpass existing utility standards for fuel, maintenance, and operating costs; plant availability; load following; safety; and durability. It is expected to meet all applicable environmental regulations. The current design concept conforming to the general definition, the basis for its selection, and the process which will be followed in further defining and updating the conceptual design.

The V 10 TDI {sup registered} for the 24h of Le Mans; Der V 10 TDI {sup registered} fuer die 24h von Le Mans

Energy Technology Data Exchange (ETDEWEB)

Baretzky, Ulrich; Diel, Hartmut; Kotauschek, Wolfgang; Dreyer, Stefan; Kuntz, Peter; Reuss, Thomas; Ullrich, Wolfgang [AUDI AG, Ingolstadt/Neckarsulm (Germany); Hatz, Wolfgang [VW AG, Wolfsburg (Germany)

2011-07-01

Since the historical first win by AUDI's V12TDI at the 24 Hours of Le Mans in 2006, the world's hardest endurance race has been won solely by diesel powered cars since then. AUDI, the pioneer of direct-injection diesel engines for road cars, has managed to forge a permanent position for diesel powertrains within motorsport and also to exploit the typical speed of development in racing. The new victorious V10TDI is again an innovative engine. In addition to its unusually low weight, the engine is characterised by its compact design and harmonic power delivery. AUDI again demonstrates its philosophy of customer aligned motorsport by developing and testing new technologies on track before introducing these to customers. (orig.)

Lightweighting Impacts on Fuel Economy, Cost, and Component Losses

Energy Technology Data Exchange (ETDEWEB)

Brooker, A. D.; Ward, J.; Wang, L.

2013-01-01

The Future Automotive Systems Technology Simulator (FASTSim) is the U.S. Department of Energy's high-level vehicle powertrain model developed at the National Renewable Energy Laboratory. It uses a time versus speed drive cycle to estimate the powertrain forces required to meet the cycle. It simulates the major vehicle powertrain components and their losses. It includes a cost model based on component sizing and fuel prices. FASTSim simulated different levels of lightweighting for four different powertrains: a conventional gasoline engine vehicle, a hybrid electric vehicle (HEV), a plug-in hybrid electric vehicle (PHEV), and a battery electric vehicle (EV). Weight reductions impacted the conventional vehicle's efficiency more than the HEV, PHEV and EV. Although lightweighting impacted the advanced vehicles' efficiency less, it reduced component cost and overall costs more. The PHEV and EV are less cost effective than the conventional vehicle and HEV using current battery costs. Assuming the DOE's battery cost target of $100/kWh, however, the PHEV attained similar cost and lightweighting benefits. Generally, lightweighting was cost effective when it costs less than $6/kg of mass eliminated.

Engine testing of ceramic cam-roller followers. Final report

Energy Technology Data Exchange (ETDEWEB)

Kalish, Y. [Detroit Diesel Corp., MI (United States)

1992-04-01

For several years, DDC has been developing monolithic ceramic heat engine components. One of the components, developed for an application in our state-of-the-art on-highway, heavy-duty diesel engine, the Series 60, is a silicon nitride cam-roller follower. Prior to starting this program, each valve train component in the Series 60 was considered for conversion to a ceramic material. Many advantages and disadvantages (benefits and risks) were considered. From this effort, one component was selected, the cam-roller follower. Using a system design approach, a ceramic cam-roller follower offered functional improvement at a reasonable cost. The purpose of the project was to inspect and test 100 domestically produced silicon nitride cam-roller followers built to the requirements of the DDC series 60 engine.

Idaho National Engineering Laboratory, Test Area North, Hangar 629 -- Photographs, written historical and descriptive data

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

The report describes the history of the Idaho National Engineering Laboratory`s Hangar 629. The hangar was built to test the possibility of linking jet engine technology with nuclear power. The history of the project is described along with the development and eventual abandonment of the Flight Engine Test hangar. The report contains historical photographs and architectural drawings.

Hybrid Vehicle Technologies and their potential for reducing oil use

Science.gov (United States)

German, John

2006-04-01

Vehicles with hybrid gasoline-electric powertrains are starting to gain market share. Current hybrid vehicles add an electric motor, battery pack, and power electronics to the conventional powertrain. A variety of engine/motor configurations are possible, each with advantages and disadvantages. In general, efficiency is improved due to engine shut-off at idle, capture of energy during deceleration that is normally lost as heat in the brakes, downsizing of the conventional engine, and, in some cases, propulsion on the electric motor alone. Ongoing increases in hybrid market share are dependent on cost reduction, especially the battery pack, efficiency synergies with other vehicle technologies, use of the high electric power to provide features desired by customers, and future fuel price and availability. Potential barriers include historically low fuel prices, high discounting of the fuel savings by new vehicle purchasers, competing technologies, and tradeoffs with other factors desired by customers, such as performance, utility, safety, and luxury features.

Numerical analysis of hydrogen and methane propagation during testing of combustion engines

Directory of Open Access Journals (Sweden)

Dvořák V.

2007-10-01

Full Text Available The research of gas-fuelled combustion engines using hydrogen or methane require accordingly equipped test benches which take respect to the higher dangerous of self ignition accidents. This article deals with numerical calculations of flow in laboratory during simulated leakage of gas-fuel from fuel system of tested engine. The influences of local suction and influences of roof exhausters on the flow in the laboratory and on the gas propagation are discussed. Results obtained for hydrogen and for methane are compared. Conclusions for design and performance of suction devices and test benches are deduced from these results.

Physics and engineering assessments of spherical torus component test facility

International Nuclear Information System (INIS)

Peng, Y.-K.M.; Neumeyer, C.A.; Kessel, C.; Rutherford, P.; Mikkelsen, D.; Bell, R.; Menard, J.; Gates, D.; Schmidt, J.; Synakowski, E.; Grisham, L.; Fogarty, P.J.; Strickler, D.J.; Burgess, T.W.; Tsai, J.; Nelson, B.E.; Sabbagh, S.; Mitarai, O.; Cheng, E.T.; El-Guebaly, L.

2005-01-01

A broadly based study of the fusion engineering and plasma science conditions of a Component Test Facility (CTF), using the Spherical Torus or Spherical Tokamak (ST) configuration, have been carried out. The chamber systems testing conditions in a CTF are characterized by high fusion neutron fluxes Γ n > 4.4x10 13 n/s/cm 2 , over size scales > 10 5 cm 2 and depth scales > 50 cm, delivering > 3 accumulated displacement per atom (dpa) per year. The desired chamber conditions can be provided by a CTF with R 0 1.2 m, A = 1.5, elongation ∼ 3.2, I p ∼ 9 MA, B T ∼ 2.5 T, producing a driven fusion burn using 36 MW of combined neutral beam and RF power. Relatively robust ST plasma conditions are adequate, which have been shown achievable [4] without active feedback manipulation of the MHD modes. The ST CTF will test the single-turn, copper alloy center leg for the toroidal field coil without an induction solenoid and neutron shielding, and require physics data on solenoid-free plasma current initiation, ramp-up, and sustainment to multiple MA level. A new systems code that combines the key required plasma and engineering science conditions of CTF has been prepared and utilized as part of this study. The results show high potential for a family of lowercost CTF devices to suit a variety of fusion engineering science test missions. (author)

40 CFR 1051.305 - How must I prepare and test my production-line vehicles or engines?

Science.gov (United States)

2010-07-01

... production-line vehicles or engines? 1051.305 Section 1051.305 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM RECREATIONAL ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.305 How must I prepare and test my production...

Eddy current testing for blade edge micro cracks of aircraft engine

Science.gov (United States)

Zhang, Wei-min; Xu, Min-dong; Gao, Xuan-yi; Jin, Xin; Qin, Feng

2017-10-01

Based on the problems of low detection efficiency in the micro cracks detection of aircraft engine blades, a differential excitation eddy current testing system was designed and developed. The function and the working principle of the system were described, the problems which contained the manufacture method of simulated cracks, signal generating, signal processing and the signal display method were described. The detection test was carried out by taking a certain model aircraft engine blade with simulated cracks as a tested specimen. The test data was processed by digital low-pass filter in the computer and the crack signals of time domain display and Lissajous figure display were acquired. By comparing the test results, it is verified that Lissajous figure display shows better performance compared to time domain display when the crack angle is small. The test results show that the eddy current testing system designed in this paper is feasible to detect the micro cracks on the aeroengine blade and can effectively improve the detection efficiency of micro cracks in the practical detection work.

Engineering development testing of the GPHS-RTG converter

International Nuclear Information System (INIS)

Cockfield, R.D.

1981-01-01

The GPHS-RTG will provide electrical power for the Galileo orbiter and for the two spacecraft of the International Solar Polar Mission. The GPHS-RTG consists of two primary assemblies: the General Purpose Heat Source, and the converter. This paper deals only with the converter, and highlights engineering tests that provide support for its design development

Super Turbocharging the Direct Injection Diesel engine

Science.gov (United States)

Boretti, Albert

2018-03-01

motivates further studies of the mechanism that may considerably benefit traditional powertrains based on diesel engines.

The new Nissan high efficient 1.2L 3cyl GDI supercharged engine enables 95g/km CO2 emissions and high driving performance

Energy Technology Data Exchange (ETDEWEB)

Kishi, Kazuaki; Satou, Takeshi [Nissan Motor Co., Ltd., Kanagawa (Japan)

2012-11-01

This paper describes a new 1.2-liter three cylinder gasoline engine named HR12DDR, with the target to achieve the lowest level CO2 in the European B-segment market and also, to satisfy the customer's driving pleasure through high output performance. This engine is developed with the consideration of meeting further strict regulations in the years ahead and of the possibility of being an alternative powertrain of diesel in the future as well. As a first step this engine was applied on the European Nissan Micra in 2011; achieving 95g/km CO2 emissions(NEDC mode). This low fuel consumption was realized mainly through technologies which scope to maximize thermal efficiency with high compression ratio, and to minimize the mechanical friction loss. The combustion was optimized by Direct Injection (DI) system. To obtain a better fuel economy performance without sacrificing high output, we chose the supercharger system with bypass valve and magnetic clutch. Details of the HR12DDR are presented here along with highlights of the applied technologies. (orig.)

In Situ Vitrification Engineering-Scale Test ES-INEL-4, ES-INEL-5, ES-INEL-6, and ES-INEL-7 Test Plan

International Nuclear Information System (INIS)

Weidner, J.R.; Stoots, P.R.

1990-10-01

The In Situ Vitrification Engineering-Scale Tests ES-4, ES-5, ES-6, and ES-7 Product Characterization Test Plan describes the methods and procedures to be used or the physical and chemical characterization of the solid product(s) resulting from the Idaho National Engineering Laboratory engineering scale in situ vitrification tests ES-4, ES-5, ES-6, and ES-7. The goals of this Test Plan are to insure that the product characterization results are sufficient to meet the data needs of the In Situ Vitrification Program and are technically and legally defensible. Important issues addressed by the test plan include sampling and analysis strategy, sampling procedures, laboratory analysis, sample control and document management, equipment, data reporting and validation, quality assurance, specific routine procedures to assess data representativeness, safety and training program, and data management. 9 refs., 1 fig., 3 tabs

Development and test of a Stirling engine driven by waste gases for the micro-CHP system

International Nuclear Information System (INIS)

Li Tie; Tang Dawei; Li Zhigang; Du Jinglong; Zhou Tian; Jia Yu

2012-01-01

In recent years, micro-CHP systems are attracting world attention. As one kind of external heating engines, Stirling engines could be applied to the micro-CHP systems driven by solar, biogas, mid-high temperature waste gases and many other heat sources. The development of a Stirling engine driven by mid-high temperature waste gases is presented first. The thermodynamic design method, the key parameters of the designed Stirling engine and its combustion chamber adapted for waste gases are described in detail. Then the performance test of the Stirling engine is carried out. During the test, the temperature of the heater head is monitored by thermocouples, and the pressure of the working fluid helium in the Stirling engine is monitored by pressure sensors. The relationships among the output shaft power, torque and speed are studied, and the pressure losses of the working fluid in the heat exchanger system are also analyzed. The test results demonstrate that the output shaft power could reach 3476 W at 1248 RPM, which is in good agreement with the predicted value of 3901 W at 1500 RPM. The test results confirm the fact that Stirling engines driven by mid-high temperature waste gases are able to achieve a valuable output power for engineering application. - Highlights: ► A β-type Stirling engine whose output power could reach about 3.5 kW is developed by ourselves. ► Waste gases are used as the heat source to drive the Stirling engine. ► Test on the relationship among the power, torque, and speed are presented. ► The pressure changing process of the working fluid in the heat exchanger system during the test is recorded and analyzed.

Scientific investigation plan for initial engineered barrier system field tests

International Nuclear Information System (INIS)

Wunan Lin.

1993-02-01

The purpose of this Scientific Investigation Plan (SIP) is to describe tests known as Initial Engineered Barrier System Field Tests (IEBSFT) and identified by Work Breakdown Structure as WBS 1.2.2.2.4. The IEBSFT are precursors to the Engineered Barrier System Field Test (EBSFT), WBS 1.2.2.2.4, to be conducted in the Exploratory Study Facility (ESF) at Yucca Mountain. The EBSFT and IEBSFT are designed to provide information on the interaction between waste packages (simulated by heated containers) and the surrounding rock mass, its vadose water, and infiltrated water. Heater assemblies will be installed in drifts or boreholes openings and heated to measure moisture movement during heat-up and subsequent cool-down of the rock mass. In some of the tests, infiltration of water into the heated rock mass will be studied. Throughout the heating and cooling cycle, instruments installed in the rock will monitor such parameters as temperature, moisture content, concentration of some chemical species, and stress and strain. Rock permeability measurements, rock and fluid (water and gas) sampling, and fracture pattern measurements will also be made before and after the test

Decontamination and decommissioning of the initial engine test facility and the IET two-inch hot-waste line

International Nuclear Information System (INIS)

Stoll, F.E.

1987-04-01

The Initial Engine Test Decommissioning Project is described in this report. The Initial Engine Test facility was constructed and operated at the National Reactor Testing Station, now known as the Idaho National Engineering Laboratory, to support the Aircraft Nuclear Propulsion Program and the Systems for Nuclear Auxiliary Power Transient test program, circa 1950 through 1960s. Due to the severe nature of these nuclear test programs, a significant amount of radioactive contamination was deposited in various portions of the Initial Engine Test Facility. Characterizations, decision analyses, and plans for decontamination and decommissioning were prepared from 1982 through 1985. Decontamination and decommissioning activities were performed in such a way that no radiological health or safety hazard to the public or to personnel at the Idaho National Engineering Laboratory remains. These decontamination and decommissioning activities began in 1985 and were completed in 1987. 13 figs

Two methodologies for physical penetration testing using social engineering

NARCIS (Netherlands)

Dimkov, T.; Pieters, Wolter; Hartel, Pieter H.

2009-01-01

During a penetration test on the physical security of an organization, if social engineering is used, the penetration tester directly interacts with the employees. These interactions are usually based on deception and if not done properly can upset the employees, violate their privacy or damage

40 CFR 1051.310 - How must I select vehicles or engines for production-line testing?

Science.gov (United States)

2010-07-01

... engines, randomly select and test one more engine. Then, calculate the required sample size for the model... distribution. σ = Test sample standard deviation (see paragraph (c)(2) of this section). x = Mean of emission... sample size for the model year as described in paragraph (c) of this section. (3) In the first test...

Design of durability test protocol for vehicular fuel cell systems operated in power-follow mode based on statistical results of on-road data

Science.gov (United States)

Xu, Liangfei; Reimer, Uwe; Li, Jianqiu; Huang, Haiyan; Hu, Zunyan; Jiang, Hongliang; Janßen, Holger; Ouyang, Minggao; Lehnert, Werner

2018-02-01

City buses using polymer electrolyte membrane (PEM) fuel cells are considered to be the most likely fuel cell vehicles to be commercialized in China. The technical specifications of the fuel cell systems (FCSs) these buses are equipped with will differ based on the powertrain configurations and vehicle control strategies, but can generally be classified into the power-follow and soft-run modes. Each mode imposes different levels of electrochemical stress on the fuel cells. Evaluating the aging behavior of fuel cell stacks under the conditions encountered in fuel cell buses requires new durability test protocols based on statistical results obtained during actual driving tests. In this study, we propose a systematic design method for fuel cell durability test protocols that correspond to the power-follow mode based on three parameters for different fuel cell load ranges. The powertrain configurations and control strategy are described herein, followed by a presentation of the statistical data for the duty cycles of FCSs in one city bus in the demonstration project. Assessment protocols are presented based on the statistical results using mathematical optimization methods, and are compared to existing protocols with respect to common factors, such as time at open circuit voltage and root-mean-square power.

Trajectory Optimization and Conceptual Study of Small Test Vehicles for Hypersonic Engine Using High-Altitude Balloon

Science.gov (United States)

Tsuchiya, Takeshi; Takenaka, Youichi; Taguchi, Hideyuki; Sawai, Shujiro

Japan Aerospace Exploration Agency, JAXA announced a long-term vision recently. In the vision, JAXA aims to develop hypersonic aircrafts. A pre-cooled turbojet engine has great potential as one of newly developed hypersonic air-breathing engines. We also expect the engine to be installed in space transportation vehicles in future. For combustion test in real flight condition of the engines, JAXA has an experimental plan with a small test vehicle falling from a high-altitude balloon. This paper applies numerical analysis and optimization techniques to conceptual designs of the test vehicle in order to obtain the best configuration and trajectory that can achieve the flight test. The results show helpful knowledge when we design prototype vehicles.

Validation Ice Crystal Icing Engine Test in the Propulsion Systems Laboratory at NASA Glenn Research Center

Science.gov (United States)

Oliver, Michael J.

2014-01-01

The Propulsion Systems Laboratory (PSL) is an existing altitude simulation jet engine test facility located at NASA Glenn Research Center in Cleveland, OH. It was modified in 2012 with the integration of an ice crystal cloud generation system. This paper documents the inaugural ice crystal cloud test in PSL--the first ever full scale, high altitude ice crystal cloud turbofan engine test to be conducted in a ground based facility. The test article was a Lycoming ALF502-R5 high bypass turbofan engine, serial number LF01. The objectives of the test were to validate the PSL ice crystal cloud calibration and engine testing methodologies by demonstrating the capability to calibrate and duplicate known flight test events that occurred on the same LF01 engine and to generate engine data to support fundamental and computational research to investigate and better understand the physics of ice crystal icing in a turbofan engine environment while duplicating known revenue service events and conducting test points while varying facility and engine parameters. During PSL calibration testing it was discovered than heated probes installed through tunnel sidewalls experienced ice buildup aft of their location due to ice crystals impinging upon them, melting and running back. Filtered city water was used in the cloud generation nozzle system to provide ice crystal nucleation sites. This resulted in mineralization forming on flow path hardware that led to a chronic degradation of performance during the month long test. Lacking internal flow path cameras, the response of thermocouples along the flow path was interpreted as ice building up. Using this interpretation, a strong correlation between total water content (TWC) and a weaker correlation between median volumetric diameter (MVD) of the ice crystal cloud and the rate of ice buildup along the instrumented flow path was identified. For this test article the engine anti-ice system was required to be turned on before ice crystal

Autonomous Cryogenic Load Operations: KSC Autonomous Test Engineer

Science.gov (United States)

Shrading, Nicholas J.

2012-01-01

The KSC Autonomous Test Engineer (KATE) program has a long history at KSC. Now a part of the Autonomous Cryogenic Load Operations (ACLO) mission, this software system has been sporadically developed over the past 20+ years. Originally designed to provide health and status monitoring for a simple water-based fluid system, it was proven to be a capable autonomous test engineer for determining sources of failure in. the system, As part.of a new goal to provide this same anomaly-detection capability for a complicated cryogenic fluid system, software engineers, physicists, interns and KATE experts are working to upgrade the software capabilities and graphical user interface. Much progress was made during this effort to improve KATE. A display ofthe entire cryogenic system's graph, with nodes for components and edges for their connections, was added to the KATE software. A searching functionality was added to the new graph display, so that users could easily center their screen on specific components. The GUI was also modified so that it displayed information relevant to the new project goals. In addition, work began on adding new pneumatic and electronic subsystems into the KATE knowledgebase, so that it could provide health and status monitoring for those systems. Finally, many fixes for bugs, memory leaks, and memory errors were implemented and the system was moved into a state in which it could be presented to stakeholders. Overall, the KATE system was improved and necessary additional features were added so that a presentation of the program and its functionality in the next few months would be a success.

40 CFR 1051.325 - What happens if an engine family fails the production-line testing requirements?

Science.gov (United States)

2010-07-01

... ENGINES AND VEHICLES Testing Production-Line Vehicles and Engines § 1051.325 What happens if an engine... for an engine family if it fails under § 1051.315. The suspension may apply to all facilities producing vehicles or engines from an engine family, even if you find noncompliant vehicles or engines only...

First-wall, blanket, and shield engineering test program for magnetically confined fusion power reactors

International Nuclear Information System (INIS)

Maroni, V.A.

1980-01-01

The key engineering areas identified for early study relate to FW/B/S system thermal-hydraulics, thermomechnics, nucleonics, electromagnetics, assembly, maintenance, and repair. Programmatic guidance derived frm planning exercises involving over thirty organizations (laboratories, industries, and universities) has indicated (1) that meaningful near term engineering testing should be feasible within the bounds of a modest funding base, (2) that there are existing facilities and expertise which can be profitably utilized in this testing, and (3) that near term efforts should focus on the measurement of engineering data and the verification/calibration of predictive methods for anticipated normal operational and transient FW/B/S conditions. The remainder of this paper discusses in more detail the planning strategies, proposed approach to near term testing, and longer range needs for integrated FW/B/S test facilities

Test results of the Chrysler upgraded automotive gas turbine engine: Initial design

Science.gov (United States)

Horvath, D.; Ribble, G. H., Jr.; Warren, E. L.; Wood, J. C.

1981-01-01

The upgraded engine as built to the original design was deficient in power and had excessive specific fuel consumption. A high instrumented version of the engine was tested to identify the sources of the engine problems. Analysis of the data shows the major problems to be low compressor and power turbine efficiency and excessive interstage duct losses. In addition, high HC and CO emission were measured at idle, and high NOx emissions at high energy speeds.

Development And Testing Of Biogas-Petrol Blend As An Alternative Fuel For Spark Ignition Engine

Directory of Open Access Journals (Sweden)

Awogbemi

2015-08-01

Full Text Available Abstract This research is on the development and testing of a biogas-petrol blend to run a spark ignition engine. A2080 ratio biogaspetrol blend was developed as an alternative fuel for spark ignition engine test bed. Petrol and biogas-petrol blend were comparatively tested on the test bed to determine the effectiveness of the fuels. The results of the tests showed that biogas petrol blend generated higher torque brake power indicated power brake thermal efficiency and brake mean effective pressure but lower fuel consumption and exhaust temperature than petrol. The research concluded that a spark ignition engine powered by biogas-petrol blend was found to be economical consumed less fuel and contributes to sanitation and production of fertilizer.

Integrated energy & emission management for hybrid electric truck with SCR aftertreatment

NARCIS (Netherlands)

Kessels, J.T.B.A.; Willems, F.P.T.; Schoot, W.J.; Bosch, P.P.J. van den

2010-01-01

Energy management in hybrid vehicles typically relates to the vehicle powertrain, whereas emission management is associated with the combustion engine and aftertreatment system. To achieve maximum performance in fuel economy and regulated pollutants, the concept of (model-based) Integrated

RENAULT Energy TCe 90. The first RENAULT gasoline 3 cylinder turbocharged engine

Energy Technology Data Exchange (ETDEWEB)

Ser, Antoine; Covin, Bruno; Levasseur, Denis [Renault SAS, Rueil-Malmaison (France); Boiarciuc, Andrei [Renault SAS, Lardy (France)

2013-08-01

This paper describes the characteristics of a new 0.9 l, 3 cylinder gasoline turbocharged engine. This new 'downsized' engine will be the core of the B and entry segment for Renault. As part of the Energy TCe family, this engine will offer a power level of 66kW close to a naturally aspirated 1.4 l, with very low CO{sub 2} emissions and reduced costs of ownership. The Energy TCe 90 is both segment leader for real life fuel consumption on Clio 4, and among the best gasoline engines regarding CO{sub 2} emissions with only 99 g CO{sub 2}/km. Based on Renault's experience in turbocharged gasoline engines, this engine features optimized combustion in order to obtain a significantly reduced fuel consumption combined with good driveability. This new product in Renault's powertrain line up offers an attractive Total Cost of Ownership for many customers. It is an intermediate offer between diesel and traditional gasoline, a clever solution for mid distance drivers. To meet all customer requirements, the main improvement features are: - Global design for consumption reduction with optimized combustion system based on high tumble motion and intake VTC. Friction reduction, introducing DLC and a new generation of controlled oil pump has been developed. - A compact exhaust system, introducing convergent exhaust ports, an integrated turbo-manifold system and a closed coupled catalyst converter for thermodynamic optimisation, providing benefits for fast warm up and high dynamic response. - Stop and Start by reinforced starter system and regenerative breaking controlled by ESM. Cost competitiveness, a constant preoccupation for Renault, is ensured by the carry-over of industrial facilities and efficient use of the Renault-Nissan Alliance's worldwide supplier base. (orig.)

Incorporating comparative genomics into the design-test-learn cycle of microbial strain engineering.

Science.gov (United States)

Sardi, Maria; Gasch, Audrey P

2017-08-01

Engineering microbes with new properties is an important goal in industrial engineering, to establish biological factories for production of biofuels, commodity chemicals and pharmaceutics. But engineering microbes to produce new compounds with high yield remains a major challenge toward economically viable production. Incorporating several modern approaches, including synthetic and systems biology, metabolic modeling and regulatory rewiring, has proven to significantly advance industrial strain engineering. This review highlights how comparative genomics can also facilitate strain engineering, by identifying novel genes and pathways, regulatory mechanisms and genetic background effects for engineering. We discuss how incorporating comparative genomics into the design-test-learn cycle of strain engineering can provide novel information that complements other engineering strategies. © FEMS 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Predictive tests to evaluate oxidative potential of engineered nanomaterials

Science.gov (United States)

Ghiazza, Mara; Carella, Emanuele; Oliaro-Bosso, Simonetta; Corazzari, Ingrid; Viola, Franca; Fenoglio, Ivana

2013-04-01

Oxidative stress constitutes one of the principal injury mechanisms through which particulate toxicants (asbestos, crystalline silica, hard metals) and engineered nanomaterials can induce adverse health effects. ROS may be generated indirectly by activated cells and/or directly at the surface of the material. The occurrence of these processes depends upon the type of material. Many authors have recently demonstrated that metal oxides and carbon-based nanoparticles may influence (increasing or decreasing) the generation of oxygen radicals in a cell environment. Metal oxide, such as iron oxides, crystalline silica, and titanium dioxide are able to generate free radicals via different mechanisms causing an imbalance within oxidant species. The increase of ROS species may lead to inflammatory responses and in some cases to the development of cancer. On the other hand carbon-based nanomaterials, such as fullerene, carbon nanotubes, carbon black as well as cerium dioxide are able to scavenge the free radicals generated acting as antioxidant. The high numbers of new-engineered nanomaterials, which are introduced in the market, are exponentially increasing. Therefore the definition of toxicological strategies is urgently needed. The development of acellular screening tests will make possible the reduction of the number of in vitro and in vivo tests to be performed. An integrated protocol that may be used to predict the oxidant/antioxidant potential of engineered nanoparticles will be here presented.

Predictive tests to evaluate oxidative potential of engineered nanomaterials

International Nuclear Information System (INIS)

Ghiazza, Mara; Carella, Emanuele; Corazzari, Ingrid; Fenoglio, Ivana; Oliaro-Bosso, Simonetta; Viola, Franca

2013-01-01

Oxidative stress constitutes one of the principal injury mechanisms through which particulate toxicants (asbestos, crystalline silica, hard metals) and engineered nanomaterials can induce adverse health effects. ROS may be generated indirectly by activated cells and/or directly at the surface of the material. The occurrence of these processes depends upon the type of material. Many authors have recently demonstrated that metal oxides and carbon-based nanoparticles may influence (increasing or decreasing) the generation of oxygen radicals in a cell environment. Metal oxide, such as iron oxides, crystalline silica, and titanium dioxide are able to generate free radicals via different mechanisms causing an imbalance within oxidant species. The increase of ROS species may lead to inflammatory responses and in some cases to the development of cancer. On the other hand carbon-based nanomaterials, such as fullerene, carbon nanotubes, carbon black as well as cerium dioxide are able to scavenge the free radicals generated acting as antioxidant. The high numbers of new-engineered nanomaterials, which are introduced in the market, are exponentially increasing. Therefore the definition of toxicological strategies is urgently needed. The development of acellular screening tests will make possible the reduction of the number of in vitro and in vivo tests to be performed. An integrated protocol that may be used to predict the oxidant/antioxidant potential of engineered nanoparticles will be here presented.

40 CFR 1039.505 - How do I test engines using steady-state duty cycles, including ramped-modal testing?

Science.gov (United States)

2010-07-01

...-state duty cycles, including ramped-modal testing? 1039.505 Section 1039.505 Protection of Environment... duty cycles, including ramped-modal testing? This section describes how to test engines under steady-state conditions. In some cases, we allow you to choose the appropriate steady-state duty cycle for an...

Testing foreign language impact on engineering students' scientific problem-solving performance

Science.gov (United States)

Tatzl, Dietmar; Messnarz, Bernd

2013-12-01

This article investigates the influence of English as the examination language on the solution of physics and science problems by non-native speakers in tertiary engineering education. For that purpose, a statistically significant total number of 96 students in four year groups from freshman to senior level participated in a testing experiment in the Degree Programme of Aviation at the FH JOANNEUM University of Applied Sciences, Graz, Austria. Half of each test group were given a set of 12 physics problems described in German, the other half received the same set of problems described in English. It was the goal to test linguistic reading comprehension necessary for scientific problem solving instead of physics knowledge as such. The results imply that written undergraduate English-medium engineering tests and examinations may not require additional examination time or language-specific aids for students who have reached university-entrance proficiency in English as a foreign language.

Educational digital resource for data analysis of Civil Engineering laboratory tests

OpenAIRE

Gustavo Henrique Nalon; Paulo Sergio de Almeida Barbosa; Walcyr Duarte Nascimento

2018-01-01

This work aims to implement and evaluate an interactive educational software that helps Civil Engineering students to perform and analyze the calculations related to different Soil Mechanics laboratory tests. This experience consists of an attempt to incorporate information and communication technologies (ICTs) into the engineering teaching-learning process. The content of the program is distributed into three different modules: “Compaction test”, “Consolidation test”, and “Direct shear test”...

Space Launch System Base Heating Test: Sub-Scale Rocket Engine/Motor Design, Development & Performance Analysis

Science.gov (United States)

Mehta, Manish; Seaford, Mark; Kovarik, Brian; Dufrene, Aaron; Solly, Nathan

2014-01-01

ATA-002 Technical Team has successfully designed, developed, tested and assessed the SLS Pathfinder propulsion systems for the Main Base Heating Test Program. Major Outcomes of the Pathfinder Test Program: Reach 90% of full-scale chamber pressure Achieved all engine/motor design parameter requirements Reach steady plume flow behavior in less than 35 msec Steady chamber pressure for 60 to 100 msec during engine/motor operation Similar model engine/motor performance to full-scale SLS system Mitigated nozzle throat and combustor thermal erosion Test data shows good agreement with numerical prediction codes Next phase of the ATA-002 Test Program Design & development of the SLS OML for the Main Base Heating Test Tweak BSRM design to optimize performance Tweak CS-REM design to increase robustness MSFC Aerosciences and CUBRC have the capability to develop sub-scale propulsion systems to meet desired performance requirements for short-duration testing.

Verification test of an engineering-scale multi-purpose radwaste incinerator

International Nuclear Information System (INIS)

Wang Peiyi; Zhou Lianquan; Ma Mingxie; Qiu Mingcai; Yang Liguo; Li Xiaohai; Zhang Xiaobin; Lu Xiaowu; Dong Jingling; Wang Xujin; Li Chuanlian; Yang Baomin

2002-01-01

The verification test of an engineering-scale multi-purpose radwaste incinerator was implemented. The test items include performance determination for the system when solid wastes (include resins) or spent oil were incinerating and off gas was cleaning, tracer test for determining decontamination factor and 72 h continuos running test. 500 h tests verify the reliability and feasibility of designs of technological process, main structure, instrument control and system safety. The incineration system ran smoothly, devices and instruments worked stably. The specifications such as capacity, volume reduction factor, carbon remainder in ash and decontamination factor all meet the design requirements

GES [Ground Engineering System] test site preparation

International Nuclear Information System (INIS)

Cox, C.M.; Mahaffey, M.K.; Miller, W.C.; Schade, A.R.; Toyoda, K.G.

1987-10-01

Activities are under way at Hanford to convert the 309 containment building and its associated service wing to a nuclear test facility for the Ground Engineering System (GES) test. Conceptual design is about 80% complete, encompassing facility modifications, a secondary heat transport system, a large vacuum system, a test article cell and handing system, control and data handling systems, and safety andl auxiliary systems. The design makes extensive use of existing equipment to minimize technical risk and cost. Refurbishment of this equipment is 25% complete. Cleanout of some 1000 m 3 of equipment from the earlier reactor test in the facility is 85% complete. An Environmental Assessment was prepared and revised to incorporate Department of Energy (DOE) comments. It is now in the DOE approval chain, where a Finding of No Significant Impact is expected. During the next year, definite design will be well advanced, long-lead procurements will be initiated, construction planning will be completed, an operator training plan will be prepared, and the site (preliminary) safety analysis report will be drafted

Engineering design of vertical test stand cryostat

International Nuclear Information System (INIS)

Suhane, S.K.; Sharma, N.K.; Raghavendra, S.; Joshi, S.C.; Das, S.; Kush, P.K.; Sahni, V.C.; Gupta, P.D.; Sylvester, C.; Rabehl, R.; Ozelis, J.

2011-01-01

Under Indian Institutions and Fermilab collaboration, Raja Ramanna Centre for Advanced Technology and Fermi National Accelerator Laboratory are jointly developing 2K Vertical Test Stand (VTS) cryostats for testing SCRF cavities at 2K. The VTS cryostat has been designed for a large testing aperture of 86.36 cm for testing of 325 MHz Spoke resonators, 650 MHz and 1.3 GHz multi-cell SCRF cavities for Fermilab's Project-X. Units will be installed at Fermilab and RRCAT and used to test cavities for Project-X. A VTS cryostat comprises of liquid helium (LHe) vessel with internal magnetic shield, top insert plate equipped with cavity support stand and radiation shield, liquid nitrogen (LN 2 ) shield and vacuum vessel with external magnetic shield. The engineering design and analysis of VTS cryostat has been carried out using ASME B and PV Code and Finite Element Analysis. Design of internal and external magnetic shields was performed to limit the magnetic field inside LHe vessel at the cavity surface 2 shield has been performed to check the effectiveness of LN 2 cooling and for compliance with ASME piping code allowable stresses.

Evolution of a test article handling system for the SP-100 ground engineering system test

International Nuclear Information System (INIS)

Shen, E.J.; Schweiger, L.J.; Miller, W.C.; Gluck, R.; Devies, S.M.

1987-04-01

A simulated space environment test of a flight prototypic SP-100 reactor, control system, and flight shield will be conducted at the Hanford Engineering Development Laboratory (HEDL). The flight prototypic components and the supporting primary heat removal system are collectively known as the Nuclear Assembly Test Article (TA). The unique configuration and materials of fabrication for the Test Article require a specialized handling facility to support installation, maintenance, and final disposal operations. Westinghouse Hanford Company, the Test Site Operator, working in conjunction with General Electric Company, the Test Article supplier, developed and evaluated several handling concepts resulting in the selection of a reference Test Article Handling System. The development of the reference concept for the handling system is presented

Cars and fuels for tomorrow: A comparative assessment

International Nuclear Information System (INIS)

Aahman, Max; Nilsson, Lars J.; Johansson, Bengt

2001-01-01

Light duty vehicles, i.e. passenger cars and light trucks, account for approximately half of global transportation energy demand and, thus, a major share of carbon dioxide and other emissions from the transport sector. Energy consumption in the transport sector is expected to grow in the future, especially in developing countries. Cars with alternative powertrains to internal combustion engines (notably battery, hybrid and fuel-cell powertrains), in combination with potentially low carbon electricity or alternative fuels (notably hydrogen and methanol), can reduce energy demand by at least 50%, and carbon dioxide and regulated emissions much further. This article presents a comparative technical and economic assessment of promising future fuel/vehicle combinations. There are several promising technologies but no obvious winners. However, the electric drivetrain is a common denominator in the alternative powertrains and continued cost reductions are important for widespread deployment in future vehicles. Development paths from current fossil fuel based systems to future carbon-neutral supply systems appear to be flexible and a gradual phasing-in of new powertrains and carbon-neutral fluid fuels or electricity is technically possible. Technology development drivers and vehicle manufacturers are found mainly in industrialised countries, but developing countries represent a growing market and may have an increasingly important role in shaping the future. (author)

Comparative analysis of battery electric, hydrogen fuel cell and hybrid vehicles in a future sustainable road transport system

Energy Technology Data Exchange (ETDEWEB)

Offer, G.J.; Brandon, N.P. [Department Earth Science Engineering, Imperial College London, SW7 2AZ (United Kingdom); Howey, D. [Department of Electrical and Electronic Engineering, Imperial College London, SW7 2AZ (United Kingdom); Contestabile, M. [Centre for Environmental Policy, Imperial College London, SW7 2AZ (United Kingdom); Clague, R. [Energy Futures Lab, Imperial College London, SW7 2AZ (United Kingdom)

2010-01-15

This paper compares battery electric vehicles (BEV) to hydrogen fuel cell electric vehicles (FCEV) and hydrogen fuel cell plug-in hybrid vehicles (FCHEV). Qualitative comparisons of technologies and infrastructural requirements, and quantitative comparisons of the lifecycle cost of the powertrain over 100,000 mile are undertaken, accounting for capital and fuel costs. A common vehicle platform is assumed. The 2030 scenario is discussed and compared to a conventional gasoline-fuelled internal combustion engine (ICE) powertrain. A comprehensive sensitivity analysis shows that in 2030 FCEVs could achieve lifecycle cost parity with conventional gasoline vehicles. However, both the BEV and FCHEV have significantly lower lifecycle costs. In the 2030 scenario, powertrain lifecycle costs of FCEVs range from $7360 to $22,580, whereas those for BEVs range from $6460 to $11,420 and FCHEVs, from $4310 to $12,540. All vehicle platforms exhibit significant cost sensitivity to powertrain capital cost. The BEV and FCHEV are relatively insensitive to electricity costs but the FCHEV and FCV are sensitive to hydrogen cost. The BEV and FCHEV are reasonably similar in lifecycle cost and one may offer an advantage over the other depending on driving patterns. A key conclusion is that the best path for future development of FCEVs is the FCHEV. (author)

Comparative analysis of battery electric, hydrogen fuel cell and hybrid vehicles in a future sustainable road transport system

International Nuclear Information System (INIS)

Offer, G.J.; Howey, D.; Contestabile, M.; Clague, R.; Brandon, N.P.

2010-01-01

This paper compares battery electric vehicles (BEV) to hydrogen fuel cell electric vehicles (FCEV) and hydrogen fuel cell plug-in hybrid vehicles (FCHEV). Qualitative comparisons of technologies and infrastructural requirements, and quantitative comparisons of the lifecycle cost of the powertrain over 100,000 mile are undertaken, accounting for capital and fuel costs. A common vehicle platform is assumed. The 2030 scenario is discussed and compared to a conventional gasoline-fuelled internal combustion engine (ICE) powertrain. A comprehensive sensitivity analysis shows that in 2030 FCEVs could achieve lifecycle cost parity with conventional gasoline vehicles. However, both the BEV and FCHEV have significantly lower lifecycle costs. In the 2030 scenario, powertrain lifecycle costs of FCEVs range from $7360 to $22,580, whereas those for BEVs range from $6460 to $11,420 and FCHEVs, from $4310 to $12,540. All vehicle platforms exhibit significant cost sensitivity to powertrain capital cost. The BEV and FCHEV are relatively insensitive to electricity costs but the FCHEV and FCV are sensitive to hydrogen cost. The BEV and FCHEV are reasonably similar in lifecycle cost and one may offer an advantage over the other depending on driving patterns. A key conclusion is that the best path for future development of FCEVs is the FCHEV.

Optimal Sizing and Control Strategy Design for Heavy Hybrid Electric Truck

Directory of Open Access Journals (Sweden)

Yuan Zou

2012-01-01

Full Text Available Due to the complexity of the hybrid powertrain, the control is highly involved to improve the collaborations of the different components. For the specific powertrain, the components' sizing just gives the possibility to propel the vehicle and the control will realize the function of the propulsion. Definitely the components' sizing also gives the constraints to the control design, which cause a close coupling between the sizing and control strategy design. This paper presents a parametric study focused on sizing of the powertrain components and optimization of the power split between the engine and electric motor for minimizing the fuel consumption. A framework is put forward to accomplish the optimal sizing and control design for a heavy parallel pre-AMT hybrid truck under the natural driving schedule. The iterative plant-controller combined optimization methodology is adopted to optimize the key parameters of the plant and control strategy simultaneously. A scalable powertrain model based on a bilevel optimization framework is built. Dynamic programming is applied to find the optimal control in the inner loop with a prescribed cycle. The parameters are optimized in the outer loop. The results are analysed and the optimal sizing and control strategy are achieved simultaneously.

Design of high temperature Engineering Test Reactor (HTTR)

International Nuclear Information System (INIS)

Saito, Shinzo; Tanaka, Toshiyuki; Sudo, Yukio

1994-09-01

Construction of High Temperature Engineering Test Reactor (HTTR) is now underway to establish and upgrade basic technologies for HTGRs and to conduct innovative basic research at high temperatures. The HTTR is a graphite-moderated and helium gas-cooled reactor with 30 MW in thermal output and outlet coolant temperature of 850degC for rated operation and 950degC for high temperature test operation. It is planned to conduct various irradiation tests for fuels and materials, safety demonstration tests and nuclear heat application tests. JAERI received construction permit of HTTR reactor facility in February 1990 after 22 months of safety review. This report summarizes evaluation of nuclear and thermal-hydraulic characteristics, design outline of major systems and components, and also includes relating R and D result and safety evaluation. Criteria for judgment, selection of postulated events, major analytical conditions for anticipated operational occurrences and accidents, computer codes used in safety analysis and evaluation of each event are presented in the safety evaluation. (author)

Design of a fusion engineering test facility

International Nuclear Information System (INIS)

Sager, P.H.

1980-01-01

The fusion Engineering Test Facility (ETF) is being designed to provide for engineering testing capability in a program leading to the demonstration of fusion as a viable energy option. It will combine power-reactor-type components and subsystems into an integrated tokamak system and provide a test bed to test blanket modules in a fusion environment. Because of the uncertainties in impurity control two basic designs are being developed: a design with a bundle divertor (Design 1) and one with a poloidal divertor (Design 2). The two designs are similar where possible, the latter having somewhat larger toroidal field (TF) coils to accommodate removal of the larger torus sectors required for the single-null poloidal divertor. Both designs have a major radius of 5.4 m, a minor radius of 1.3 m, and a D-shaped plasma with an elongation of 1.6. Ten TF coils are incorporated in both designs, producing a toroidal field of 5.5 T on-axis. The ohmic heating and equilibrium field (EF) coils supply sufficient volt-seconds to produce a flat-top burn of 100 s and a duty cycle of 135 s, including a start of 12 s, a burn termination of 10 s, and a pumpdown of 13 s. The total fusion power during burn is 750 MW, giving a neutron wall loading of 1.5 MW/m 2 . In Design 1 of the poloidal field (PF) coils except the fast-response EF coils are located outside the FT coils and are superconducting. The fast-response coils are located inside the TF coil bore near the torus and are normal conducting so that they can be easily replaced.In Design 2 all of the PF coils are located outside the TF coils and are superconducting. Ignition is achieved with 60 MW of neutral beam injection at 150 keV. Five megawatts of radio frequency heating (electron cyclotron resonance heating) is used to assist in the startup and limit the breakdown requirement to 25 V

Results from tests of a Stirling engine and wood chips gasifier plant

DEFF Research Database (Denmark)

Carlsen, Henrik; Bovin, Jonas Kabell; Werling, J.

2002-01-01

The combination of thermal gasification and a Stirling engine is an interesting concept for use in small Combined Heat and Power (CHP) plants based on biomass, because the need for gas cleaning is eliminated and problems with fouling of the Stirling engine heater are considerably reduced....... Furthermore, the overall electric efficiency of the system can be improved. At the Technical University of Denmark a small CHP plant based on a Stirling engine and an updraft gasifier has been developed and tested successfully. The advantages of updraft gasifiers are the simplicity and that the amount...... of the Stirling engine reduces the problems with tar to a minor problem in the design of the burner. The Stirling engine, which has an electric power output of 35 kW, is specifically designed for utilisation of fuels with a content of particles. The gas burner for the engine is designed for low specific energy...

40 CFR 85.1506 - Inspection and testing of imported motor vehicles and engines.

Science.gov (United States)

2010-07-01

... motor vehicles and engines. 85.1506 Section 85.1506 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) AIR PROGRAMS (CONTINUED) CONTROL OF AIR POLLUTION FROM MOBILE SOURCES Importation of Motor Vehicles and Motor Vehicle Engines § 85.1506 Inspection and testing of imported motor vehicles and...

Comparative tests of bench equipment for fuel control system testing of gas-turbine engine

Science.gov (United States)

Shendaleva, E. V.

2018-04-01

The relevance of interlaboratory comparative researches is confirmed by attention of world metrological community to this field of activity. Use of the interlaboratory comparative research methodology not only for single gages collation, but also for bench equipment complexes, such as modeling stands for fuel control system testing of gas-turbine engine, is offered. In this case a comparative measure of different bench equipment will be the control fuel pump. Ensuring traceability of measuring result received at test benches of various air enterprises, development and introduction of national standards to practice of bench tests and, eventually, improvement of quality and safety of a aircraft equipment is result of this approach.

Multicylinder Diesel Engine Tests with Unstabilized Water-in-Fuel Emulsions

Science.gov (United States)

1981-06-01

Two diesel engines representative of the four-stroke cycle and two-stroke cycle main propulsion units installed in U.S. Coast Guard WPB class cutters were operated in a test environment in an attempt to demonstrate significant fuel savings associated...

Downsized Boosted Engine Benchmarking Method and Results (SAE Paper 2015-01-1266)

Science.gov (United States)

Light-duty vehicle greenhouse gas (GHG) and fuel economy (FE) standards for MYs 2012 -2025 are requiring vehicle powertrain to become much more efficient. One key technology strategy that vehicle manufacturers are using to help comply with GHG and FE standards is to replace natu...

Long term durability tests of small engines fueled with bio-ethanol / gasoline blends

International Nuclear Information System (INIS)

Tippayawong, N.; Kundhawiworn, N.; Jompakdee, W.

2006-01-01

The paper presents the result of an ongoing research to evaluate performance and wear of small, single cylinder, naturally aspirated, agricultural spark ignition engines using biomass-derived ethanol and gasoline blends. The reference gasoline fuel was selected to be representative of gasoline typically available in Thailand. Long-term engine tests of 10% and 20% ethanol / gasoline blends as well as the reference fuel were performed at a constant speed of 2300 rpm under part load condition up to 200 operation hours for each fuel type. Engine brake power, specific fuel consumption, carbon deposits and surface wear were measured and compared between neat gasoline and ethanol/ gasoline blends. It was found that blended fuels appeared to affect the engine performance in a similar way and compared well with the base gasoline fuel. From the results obtained, it was found that engine brake power and specific fuel consumption changed slightly with running time and were not found to have any significant change between different fuel blends. There were carbon deposits buildup on the spark plug, the intake port and exhaust valve stem for all fuels used. Surface wear was not significantly different in the test engines between neat gasoline or ethanol/gasoline blend fuelling

Tear Down and Inspection of the Cummins VTA-903 Evaluated Using the Single Common Powertrain Lubricant SCPL

Science.gov (United States)

2013-12-13

the General Engine Products (GEP) family of engines used in the High Mobility Multipurpose Wheeled Vehicle (HMMWV), and the Caterpillar (CAT) C7 used...Mobility Multipurpose Wheeled Vehicle HP Horsepower ID Inside Diameter lb-ft Pound Feet MIL-PRF Military Performance Specification NATO North... eccentricity [4, pg 4-128] o Liner bores from test engine measured thrust and anti-thrust @ 25mm from top, 105mm from top, and 180mm from top (i.e

Calculated concentrations of any radionuclide deposited on the ground by release from underground nuclear detonations, tests of nuclear rockets, and tests of nuclear ramjet engines

International Nuclear Information System (INIS)

Hicks, H.G.

1981-11-01

This report presents calculated gamma radiation exposure rates and ground deposition of related radionuclides resulting from three types of event that deposited detectable radioactivity outside the Nevada Test Site complex, namely, underground nuclear detonations, tests of nuclear rocket engines and tests of nuclear ramjet engines

Engineering test station for TFTR blanket module experiments

International Nuclear Information System (INIS)

Jassby, D.L.; Leinoff, S.

1979-12-01

A conceptual design has been carried out for an Engineering Test Station (ETS) which will provide structural support and utilities/instrumentation services for blanket modules positioned adjacent to the vacuum vessel of the TFTR (Tokamak Fusion Test Reactor). The ETS is supported independently from the Test Cell floor. The ETS module support platform is constructed of fiberglass to eliminate electromagnetic interaction with the pulsed tokamak fields. The ETS can hold blanket modules with dimensions up to 78 cm in width, 85 cm in height, and 105 cm in depth, and with a weight up to 4000 kg. Interfaces for all utility and instrumentation requirements are made via a shield plug in the TFTR igloo shielding. The modules are readily installed or removed by means of TFTR remote handling equipment

Implementation of an optimal control energy management strategy in a hybrid truck

NARCIS (Netherlands)

Mullem, D. van; Keulen, T. van; Kessels, J.T.B.A.; Jager, B. de; Steinbuch, M.

2010-01-01

Energy Management Strategies for hybrid powertrains control the power split, between the engine and electric motor, of a hybrid vehicle, with fuel consumption or emission minimization as objective. Optimal control theory can be applied to rewrite the optimization problem to an optimization

System-level design optimization of a hybrid tug

NARCIS (Netherlands)

Hofman, T.; Naaborg, M.; Sciberras, E.

2017-01-01

Designing a new vessel is a complex multi-objective design process. It involves knowledge from different fields, like naval architecture and mechanical engineering. Assessment of an optimal design for more complex topologies than a conventional Diesel powertrain becomes more difficult due to the

Advanced Combustion and Emission Control Technical Team Roadmap

Energy Technology Data Exchange (ETDEWEB)

None

2013-06-01

The Advanced Combustion and Emission Control (ACEC) Technical Team is focused on removing technical barriers to the commercialization of advanced, high-efficiency, emission-compliant internal combustion (IC) engines for light-duty vehicle powertrains (i.e., passenger car, minivan, SUV, and pickup trucks).

Leakage and Power Loss Test Results for Competing Turbine Engine Seals

National Research Council Canada - National Science Library

Proctor, Margaret

2004-01-01

.... To address engine manufacturers' concerns about the heat generation and power loss from these contacting seals, brush, finger, and labyrinth seals were tested in the NASA High Speed, High Temperature...

Spacecraft Testing Programs: Adding Value to the Systems Engineering Process

Science.gov (United States)

Britton, Keith J.; Schaible, Dawn M.

2011-01-01

Testing has long been recognized as a critical component of spacecraft development activities - yet many major systems failures may have been prevented with more rigorous testing programs. The question is why is more testing not being conducted? Given unlimited resources, more testing would likely be included in a spacecraft development program. Striking the right balance between too much testing and not enough has been a long-term challenge for many industries. The objective of this paper is to discuss some of the barriers, enablers, and best practices for developing and sustaining a strong test program and testing team. This paper will also explore the testing decision factors used by managers; the varying attitudes toward testing; methods to develop strong test engineers; and the influence of behavior, culture and processes on testing programs. KEY WORDS: Risk, Integration and Test, Validation, Verification, Test Program Development

Summary of Altitude Pulse Testing of a 100-lbf L02/LCH4 Reaction Control Engine

Science.gov (United States)

Marshall, William M.; Kleinhenz, Julie E.

2011-01-01

Recently, liquid oxygen-liquid methane (LO2/LCH4) has been considered as a potential "green" propellant alternative for future exploration missions. The Propulsion and Cryogenic Advanced Development (PCAD) project has been tasked by NASA to develop this propulsion combination to enable safe and cost effective exploration missions. To date, limited experience with such combinations exist, and as a result a comprehensive test program is critical to demonstrating the viability of implementing such a system. The NASA Glenn Research Center has conducted a test program of a 100-lbf (445-N) reaction control engine (RCE) at the center s Altitude Combustion Stand (ACS), focusing on altitude testing over a wide variety of operational conditions. The ACS facility includes a unique propellant conditioning feed system (PCFS) which allows precise control of propellant inlet conditions to the engine. Engine performance as a result of these inlet conditions was examined extensively during the test program. This paper is a companion to the previous specific impulse testing paper, and discusses the pulsed mode operation portion of testing, with a focus on minimum impulse bit (I-bit) and repeatable pulse performance. The engine successfully demonstrated target minimum impulse bit performance at all conditions, as well as successful demonstration of repeatable pulse widths. Some anomalous conditions experienced during testing are also discussed, including a double pulse phenomenon which was not noted in previous test programs for this engine.

Simulation of diesel engine emissions on the example of Fiat Panda in the NEDC test

Directory of Open Access Journals (Sweden)

Botwinska Katarzyna

2017-01-01

Full Text Available Road transport may be deemed a strategic branch of modern economy. Unfortunately, a rapid increase in the number of on-road motor vehicles entails some negative consequences as well, for instance, excessive concentration of exhausts produced by engines which results in deterioration of air quality. EURO emission standards which define acceptable limits for exhaust emissions of power units is an example of an activity performed in attempt to improve air quality. The EURO standard defines permissible amount of exhausts produced by a vehicle. Presently new units are examined through NEDC test. For the purpose of this thesis, a virtual test stand in a form of a computer simulation of a chassis dynamometer was used to simulate emission of a diesel engine (compression-ignition engine in the NEDC test. Actual parameters of the 1.3 MultiJet engine of the Fiat Panda passenger car of 2014 were applied in the model. The simulation was carried out in the Matlab Simulink environment. The simulation model of the Fiat Panda passenger car enables the designation of the emission waveform for all test stages which corresponds to the values received during an approval test in real-life conditions.

Simulation of diesel engine emissions on the example of Fiat Panda in the NEDC test

Science.gov (United States)

Botwinska, Katarzyna; Mruk, Remigiusz; Słoma, Jacek; Tucki, Karol; Zaleski, Mateusz

2017-10-01

Road transport may be deemed a strategic branch of modern economy. Unfortunately, a rapid increase in the number of on-road motor vehicles entails some negative consequences as well, for instance, excessive concentration of exhausts produced by engines which results in deterioration of air quality. EURO emission standards which define acceptable limits for exhaust emissions of power units is an example of an activity performed in attempt to improve air quality. The EURO standard defines permissible amount of exhausts produced by a vehicle. Presently new units are examined through NEDC test. For the purpose of this thesis, a virtual test stand in a form of a computer simulation of a chassis dynamometer was used to simulate emission of a diesel engine (compression-ignition engine) in the NEDC test. Actual parameters of the 1.3 MultiJet engine of the Fiat Panda passenger car of 2014 were applied in the model. The simulation was carried out in the Matlab Simulink environment. The simulation model of the Fiat Panda passenger car enables the designation of the emission waveform for all test stages which corresponds to the values received during an approval test in real-life conditions.

Powertrain technologies for sustainable mobility at Mercedes-Benz; Antriebstechnologien zur nachhaltigen Mobilitaet bei Mercedes-Benz

Energy Technology Data Exchange (ETDEWEB)

Mikulic, Leopold; Kohler, Herbert [Daimler AG, Stuttgart (Germany)

2009-07-01

The mobility of the future is subject to boundary conditions such as the shortage of resources, regulatory restrictions and changed behaviour of utilization of the vehicle. Daimler AG (Stuttgart, Federal Republic of Germany) meets these challenges with a Roadmap for a sustainable mobility. Apart from the search for improved energy sources, this Roadmap develops in three stages. The first step begins with the optimization of the combustion engines. Spark ignition engines are to be made as economical as diesel engines. Diesel engines are to be made as clean as spark ignition engines. Milestones here are the direct injection of the second generation with spark ignition engines and the BlueTec technology with diesel engines. Both principles of combustion flow into the DIESOTTO engine concept which unites the advantages of both combustion concepts. In the second step, the combustion engine in modular hybrid concepts is supported by electric motors. Depending upon intended purpose and customer requirements the graduated hybrid functionalities such as asynchronous operation, boosting, recupation are made available up to purely electrical driving. These technologies lead to emission-free driving with battery vehicles and gas cell vehicles in the third step. This future already began: Daimler AG has the world-wide largest test fleet of battery vehicles and gas cell vehicles. Daimler AG brings itself into the process of alteration and actively plays a leading role in the tradition of the inventors of automobiles.

Design, fabrication, and testing of a sodium evaporator for the STM4-120 kinematic Stirling engine

Energy Technology Data Exchange (ETDEWEB)

Rawlinson, K.S.; Adkins, D.R.

1995-05-01

This report describes the development and testing of a compact heat-pipe heat exchanger kW(e) designed to transfer thermal energy from hot combustion gases to the heater tubes of a 25-kW(e) Stirling engine. In this system, sodium evaporates from a surface that is heated by a stream of hot gases. The liquid metal then condenses on the heater tubes of a Stirling engine, where energy is transferred to the engine`s helium working fluid. Tests on a prototype unit illustrated that a compact (8 cm {times} 13 cm {times} 16 cm) sodium evaporator can routinely transfer 15 kW(t) of energy at an operating vapor temperature of 760 C. Four of these prototype units were eventually used to power a 25-kW(e) Stirling engine system. Design details and test results from the prototype unit are presented in this report.

Can disc diffusion susceptibility tests assess the antimicrobial activity of engineered nanoparticles?

NARCIS (Netherlands)

Kourmouli, A.; Valenti, M.; van Rijn, E.; Beaumont, H.J.E.; Kalantzi, Olga Ioanna; Schmidt-Ott, A.; Biskos, G.

2018-01-01

The use of disc diffusion susceptibility tests to determine the antibacterial activity of engineered nanoparticles (ENPs) is questionable because their low diffusivity practically prevents them from penetrating through the culture media. In this study, we investigate the ability of such a test,

The SPHINX reactor for engineering tests

International Nuclear Information System (INIS)

Adamov, E.O.; Artamkin, K.N.; Bovin, A.P.; Bulkin, Y.M.; Kartashev, E.F.; Korneev, A.A.; Stenbok, I.A.; Terekhov, A.S.; Khmel'Shehikov, V.V.; Cherkashov, Y.M.

1990-01-01

A research reactor known as SPHINX is under development in the USSR. The reactor will be used mainly to carry out tests on mock-up power reactor fuel assemblies under close-to-normal parameters in experimental loop channels installed in the core and reflector of the reactor, as well as to test samples of structural materials in ampoule and loop channels. The SPHINX reactor is a channel-type reactor with light-water coolant and moderator. Maximum achievable neutron flux density in the experimental channels (cell composition 50% Fe, 50% H 2 O) is 1.1 X 10 15 neutrons/cm 2 · s for fast neutrons (E > 0.1 MeV) and 1.7 X 10 15 for thermal neutrons at a reactor power of 200 MW. The design concepts used represent a further development of the technical features which have met with approval in the MR and MIR channel-type engineering test reactors currently in use in the USSR. The 'in-pond channel' construction makes the facility flexible and eases the carrying out of experimental work while keeping discharges of radioactivity into the environment to a low level. The reactor and all associated buildings and constructions conform to modern radiation safety and environmental protection requirements

System engineering approach in the EU Test Blanket Systems Design Integration

International Nuclear Information System (INIS)

Panayotov, D.; Sardain, P.; Boccaccini, L.V.; Salavy, J.-F.; Cismondi, F.; Jourd'Heuil, L.

2011-01-01

The complexity of the Test Blanket Systems demands diverse and comprehensive integration activities. Test Blanket Modules - Consortia of Associates (TBM-CA) applies the system engineering methods in all stages of the Test Blanket System (TBS) design integration. Completed so far integration engineering tasks cover among others status and initial set of TBS operating parameters; list of codes, standards and regulations related to TBS; planning of the TBS interfaces and baseline documentation. Most of the attention is devoted to the establishment the Helium-Cooled Lithium Lead (HCLL) and Helium-Cooled Pebble Bed Lead (HCPB) TBS configuration baseline, TBS break down into sub-systems, identification, definition and management of the internal and external interfaces, development of the TBS plant break down structure (PBS), establishment and management of the required TBS baseline documentation infrastructure. Break down of the TBS into sub-systems that is crucial for the further design and interfaces' management has been selected considering several options and using specific evaluation criteria. Process of the TBS interfaces management covers the planning, definition and description, verification and review, non-conformances and deviations, and modification and improvement processes. Process of interfaces review is developed, identifying the actors, input, activities and output of the review. Finally the relations and interactions of system engineering processes with TBM configuration management and TBM-CA Quality Management System are discussed.

Thermal Environmental Testing of NSTAR Engineering Model Ion Thrusters

Science.gov (United States)

Rawlin, Vincent K.; Patterson, Michael J.; Becker, Raymond A.

1999-01-01

NASA's New Millenium program will fly a xenon ion propulsion system on the Deep Space 1 Mission. Tests were conducted under NASA's Solar Electric Propulsion Technology Applications Readiness (NSTAR) Program with 3 different engineering model ion thrusters to determine thruster thermal characteristics over the NSTAR operating range in a variety of thermal environments. A liquid nitrogen-cooled shroud was used to cold-soak the thruster to -120 C. Initial tests were performed prior to a mature spacecraft design. Those results and the final, severe, requirements mandated by the spacecraft led to several changes to the basic thermal design. These changes were incorporated into a final design and tested over a wide range of environmental conditions.

Ecotoxicity of engineered nanoparticles to aquatic invertebrates: a brief review and recommendations for future toxicity testing

DEFF Research Database (Denmark)

Baun, Anders; Hartmann, Nanna Isabella Bloch; Grieger, Khara Deanne

2008-01-01

Based on a literature review and an overview of toxic effects of engineered nanoparticles in aquatic invertebrates, this paper proposes a number of recommendations for the developing field of nanoecotoxicology by highlighting the importance of invertebrates as sensitive and relevant test organisms...... through standardized short-term (lethality) tests with invertebrates as a basis for investigating behaviour and bioavailability of engineered nanoparticles in the aquatic environment. Based on this literature review, we further recommend that research is directed towards invertebrate tests employing long....... Results show that there is a pronounced lack of data in this field (less than 20 peer-reviewed papers are published so far), and the most frequently tested engineered nanoparticles in invertebrate tests are C-60, carbon nanotubes, and titanium dioxide. In addition, the majority of the studies have used...

Product evaluation of in situ vitrification engineering, Test 4

International Nuclear Information System (INIS)

Loehr, C.A.; Weidner, J.R.; Bates, S.O.

1991-09-01

This report is one of several that evaluates the In Situ Vitrification (ISV) Engineering-Scale Test 4 (ES-4). This document describes the chemical and physical composition, microstructure, and leaching characteristics of ES-4 product samples; these data provide insight into the expected performance of a vitrified product in an ISV buried waste application similar to that studied in ES-4

40 CFR 1068.415 - How do I test my engines/equipment?

Science.gov (United States)

2010-07-01

... POLLUTION CONTROLS GENERAL COMPLIANCE PROVISIONS FOR ENGINE PROGRAMS Selective Enforcement Auditing § 1068... for the year, you may test a minimum of one per 24-hour period. If you request and justify it, we may...

Automatic testing devices for diesel engines for the quality control in engine production

Energy Technology Data Exchange (ETDEWEB)

Homann, R; Homilius, K

1979-01-01

A device which generates the torque for the brakes is the most important functional group in engine test stands. Hydraulic dynamometric brakes are serially produced for power ranges from 210 up to 70000 kw and maximum revolutions up to 10000 rpm. Eddy current brakes can be supplied for the power range of 40 to 3600 kW. Compared to the hydraulic dynamometric brake they have a larger rev-range for control while both have the same torque. Electric machines used as dynamometric brakes make it possible to recuperate electric energy. The properties of the individual braking devices are compared. Torque and number of revolutions are calculated digitally. Test methods are automatised as far as possible. There are four control methods: time plan, perforated strip, magnetic tape or computer.

Trajectory Optimization and Conceptual Study of Small Test Vehicles for a Hypersonic Engine Using a High-Altitude Balloon

Science.gov (United States)

Tsuchiya, Takeshi; Takenaka, Youichi; Taguchi, Hideyuki; Sawai, Shujiro

The Japan Aerospace Exploration Agency, JAXA, announced a long-term vision recently. In the vision, JAXA aims to develop hypersonic aircrafts. A pre-cooled turbojet engine has great potential as one of newly developed hypersonic airbreathing engines. We also expect the engine to be installed in space transportation vehicles in the future. For combustion test in the real flight conditions of the engines, JAXA has an experimental plan where a small test vehicle is released from a high-altitude balloon. This paper applies numerical analysis and optimization techniques to conceptual designs of the test vehicle in order to obtain the best configuration and trajectory for the flight test. The results show helpful knowledge for designing prototype vehicles.

Overview of the main challenges for the engineering design of the test facilities system of IFMIF

International Nuclear Information System (INIS)

Molla, J.; Nakamura, K.

2009-01-01

High intense radiation fields were demanded to IFMIF to address the lack of information on effects in materials due to radiation fields with fusion reactor features. Such intense radiation fields will also produce a number of unwanted effects in exposed materials and components. The main difficulties to achieve a reliable engineering design of the Test Facilities System during the Engineering Validation and the Engineering Design phase of IFMIF now under development are reviewed in this paper. The most challenging activities will be the design of the high flux test module, the creep fatigue test module, the test cell and the remote handling system. The intense radiation fields in the irradiation area and the high availability required for IFMIF (70%) are the main reasons for these difficulties.

Engineering testing and technology projects FY 1996 Site Support Program Plan, WBS 6.3.3 and 6.3.8. Revision 1

International Nuclear Information System (INIS)

Brown, L.C.

1995-10-01

The engineering laboratory services for development, assembly, testing, and evaluation to support the resolution of WHC, Hanford, and DOE complex wide engineering issues for 1996 are presented. Primary customers are: TWRS, spent nuclear fuels, transition projects, liquid effluent program, and other Hanford contractors and programs. Products and services provided include: fabrication and assembly facilities for prototype and test equipment, development testing, proof of principle testing, instrumentation testing, nondestructive examination application development and testing, prototype equipment design and assembly, chemical engineering unit operations testing, engineering test system disposal, and safety issue resolution

Optical Measurement Techniques for Rocket Engine Testing and Component Applications: Digital Image Correlation and Dynamic Photogrammetry

Science.gov (United States)

Gradl, Paul

2016-01-01

NASA Marshall Space Flight Center (MSFC) has been advancing dynamic optical measurement systems, primarily Digital Image Correlation, for extreme environment rocket engine test applications. The Digital Image Correlation (DIC) technology is used to track local and full field deformations, displacement vectors and local and global strain measurements. This technology has been evaluated at MSFC through lab testing to full scale hotfire engine testing of the J-2X Upper Stage engine at Stennis Space Center. It has been shown to provide reliable measurement data and has replaced many traditional measurement techniques for NASA applications. NASA and AMRDEC have recently signed agreements for NASA to train and transition the technology to applications for missile and helicopter testing. This presentation will provide an overview and progression of the technology, various testing applications at NASA MSFC, overview of Army-NASA test collaborations and application lessons learned about Digital Image Correlation.

The Application of Hardware in the Loop Testing for Distributed Engine Control

Science.gov (United States)

Thomas, George L.; Culley, Dennis E.; Brand, Alex

2016-01-01

The essence of a distributed control system is the modular partitioning of control function across a hardware implementation. This type of control architecture requires embedding electronics in a multitude of control element nodes for the execution of those functions, and their integration as a unified system. As the field of distributed aeropropulsion control moves toward reality, questions about building and validating these systems remain. This paper focuses on the development of hardware-in-the-loop (HIL) test techniques for distributed aero engine control, and the application of HIL testing as it pertains to potential advanced engine control applications that may now be possible due to the intelligent capability embedded in the nodes.

Aircraft Engine Noise Research and Testing at the NASA Glenn Research Center

Science.gov (United States)

Elliott, Dave

2015-01-01

The presentation will begin with a brief introduction to the NASA Glenn Research Center as well as an overview of how aircraft engine noise research fits within the organization. Some of the NASA programs and projects with noise content will be covered along with the associated goals of aircraft noise reduction. Topics covered within the noise research being presented will include noise prediction versus experimental results, along with engine fan, jet, and core noise. Details of the acoustic research conducted at NASA Glenn will include the test facilities available, recent test hardware, and data acquisition and analysis methods. Lastly some of the actual noise reduction methods investigated along with their results will be shown.

Mathematical model of marine diesel engine simulator for a new methodology of self propulsion tests

Energy Technology Data Exchange (ETDEWEB)

Izzuddin, Nur; Sunarsih,; Priyanto, Agoes [Faculty of Mechanical Engineering, Universiti Teknologi Malaysia, 81310 Skudai, Johor (Malaysia)

2015-05-15

As a vessel operates in the open seas, a marine diesel engine simulator whose engine rotation is controlled to transmit through propeller shaft is a new methodology for the self propulsion tests to track the fuel saving in a real time. Considering the circumstance, this paper presents the real time of marine diesel engine simulator system to track the real performance of a ship through a computer-simulated model. A mathematical model of marine diesel engine and the propeller are used in the simulation to estimate fuel rate, engine rotating speed, thrust and torque of the propeller thus achieve the target vessel’s speed. The input and output are a real time control system of fuel saving rate and propeller rotating speed representing the marine diesel engine characteristics. The self-propulsion tests in calm waters were conducted using a vessel model to validate the marine diesel engine simulator. The simulator then was used to evaluate the fuel saving by employing a new mathematical model of turbochargers for the marine diesel engine simulator. The control system developed will be beneficial for users as to analyze different condition of vessel’s speed to obtain better characteristics and hence optimize the fuel saving rate.

Scope and status of the USA Engineering Test Facility including relevant TFTR research and development

International Nuclear Information System (INIS)

Becraft, W.R.; Reardon, P.J.

1980-01-01

The vehicle by which the fusion program would move into the engineering testing phase of fusion power development is designated the Engineering Test Facility (ETF). The progress toward the design and construction of the ETF will reflect the significant achievements of past, present, and future experimental tokamak devices. Some of the features of this foundation of experimental results and relevant engineering designs and operation will derive from the Tokamak Fusion Test Reactor (TFTR) Project, now nearing the completion of its construction phase. The ETF would provide a test-bed for reactor components in the fusion environment. In order to initiate preliminary planning for the ETF decision, the Office of Fusion Energy (OFE) established the ETF Design Center activity to prepare the design of the ETF. This paper describes the design status of the ETF and discusses some highlights of the TFTR R and D work

Scope and status of the USA Engineering Test Facility including relevant TFTR research and development

International Nuclear Information System (INIS)

Becraft, W.R.; Reardon, P.J.

1981-01-01

The vehicle by which the fusion programme would move into the engineering testing phase of fusion power development is designated the Engineering Test Facility (ETF). The progress toward the design and construction of the ETF will reflect the significant achievements of past, present, and future experimental tokamak devices. Some of the features of this foundation of experimental results and relevant engineering designs and operation will derive from the Tokamak Fusion Test Reactor (TFTR) Project, now nearing the completion of its construction phase. The ETF would provide a test-bed for reactor components in the fusion environment. To initiate preliminary planning for the ETF decision, the Office of Fusion Energy (OFE) established the ETF Design Center activity to prepare the design of the ETF. This paper describes the design status of the ETF and discusses some highlights of the TFTR R and D work. (author)

40 CFR 1045.310 - How must I select engines for production-line testing?

Science.gov (United States)

2010-07-01

... select and test one more engine. Then, calculate the required sample size for the model year as described.... It defines 95% confidence intervals for a one-tail distribution. σ = Test sample standard deviation (see paragraph (c)(2) of this section). x = Mean of emission test results of the sample. STD = Emission...

Development Testing of 1-Newton ADN-Based Rocket Engines

Science.gov (United States)

Anflo, K.; Gronland, T.-A.; Bergman, G.; Nedar, R.; Thormählen, P.

2004-10-01

With the objective to reduce operational hazards and improve specific and density impulse as compared with hydrazine, the Research and Development (R&D) of a new monopropellant for space applications based on AmmoniumDiNitramide (ADN), was first proposed in 1997. This pioneering work has been described in previous papers1,2,3,4 . From the discussion above, it is clear that cost savings as well as risk reduction are the main drivers to develop a new generation of reduced hazard propellants. However, this alone is not enough to convince a spacecraft builder to choose a new technology. Cost, risk and schedule reduction are good incentives, but a spacecraft supplier will ask for evidence that this new propulsion system meets a number of requirements within the following areas: This paper describes the ongoing effort to develop a storable liquid monopropellant blend, based on AND, and its specific rocket engines. After building and testing more than 20 experimental rocket engines, the first Engineering Model (EM-1) has now accumulated more than 1 hour of firing-time. The results from test firings have validated the design. Specific impulse, combustion stability, blow-down capability and short pulse capability are amongst the requirements that have been demonstrated. The LMP-103x propellant candidate has been stored for more than 1 year and initial material compatibility screening and testing has started. 1. Performance &life 2. Impact on spacecraft design &operation 3. Flight heritage Hereafter, the essential requirements for some of these areas are outlined. These issues are discussed in detail in a previous paper1 . The use of "Commercial Of The Shelf" (COTS) propulsion system components as much as possible is essential to minimize the overall cost, risk and schedule. This leads to the conclusion that the Technology Readiness Level (TRL) 5 has been reached for the thruster and propellant. Furthermore, that the concept of ADN-based propulsion is feasible.

Simulation and control of an automotive dry clutch

NARCIS (Netherlands)

Serrarens, A.F.A.; Dassen, M.; Steinbuch, M.

2004-01-01

In this paper the dynamic behavior and control of an automotive dry clutch is analyzed. Thereto, a straight-forward model of the clutch is embedded within a dynamic model of an automotive powertrain comprising an internal combustion engine, drivetrain and wheels moving a vehicle through tire-road

ARC Researchers at 2016 SAE Congress

Science.gov (United States)

. Henein, Wayne State University 1:30 pm 2016-01-0310 An Engine Thermal Management System Design for ; Zissimos Mourelatos, Oakland University Session PFL370; Room 360 Holistic Session on Fuel Consumption and , powertrain, and supporting electromechanical subsystems related to energy management. 4:30 pm 2016-01-1239

Synchrotron radiation losses in Engineering Test Reactors (ETRs)

International Nuclear Information System (INIS)

Uckan, N.A.

1987-11-01

In next-generation Engineering Test Reactors (ETRs), one major objective is envisioned to be a long-pulse or steady-state burn using noninductive current drive. At the high temperatures needed for efficient current drive, synchrotron radiation could represent a large power loss, especially if wall reflectivity (R) is very low. Many INTOR-class ETR designs [Fusion Engineering Reactor (FER), Next European Torus (NET), OTR, Tokamak Ignition/Burn Engineering Reactor (TIBER), etc.] call for carbon-covered surfaces for which wall reflectivity is uncertain. Global radiation losses are estimated for these devices using empirical expressions given by Trubnikov (and others). Various operating scenarios are evaluated under the assumption that the plasma performance is limited by either the density limit (typical of the ignition phase) or the beta limit (typical of the current drive phase). For a case with ≥90% wall reflectivity, synchrotron radiation is not a significant contribution to the overall energy balance (the ratio of synchrotron to alpha power is less than 10 to 20%, even at ∼ 30 keV) and thus should not adversely alter performance in these devices. In extreme cases with 0% wall reflectivity, the ratio of synchrotron radiation to alpha power may approach 30 to 60% (depending on the device and limiting operating scenario), adversely affecting the performance characteristics. 12 refs., 7 tabs

40 CFR Table 6 to Subpart IIIi of... - Optional 3-Mode Test Cycle for Stationary Fire Pump Engines

Science.gov (United States)

2010-07-01

... Engines [As stated in § 60.4210(g), manufacturers of fire pump engines may use the following test cycle... 40 Protection of Environment 6 2010-07-01 2010-07-01 false Optional 3-Mode Test Cycle for Stationary Fire Pump Engines 6 Table 6 to Subpart IIII of Part 60 Protection of Environment ENVIRONMENTAL...

Analysis of the CVT Efficiency by Simulation

Directory of Open Access Journals (Sweden)

Valerian Croitorescu

2011-09-01

Full Text Available All vehicle manufacturers desire an ideal vehicle that has the highest powertrain efficiency, best safety factor and ease of maintenance while being environmentally friendly. These highly valued vehicle development characteristics are only reachable after countless research hours. One major powertrain component to be studied in relation to these demands is the Continuous Variable Transmission that a Hybrid Electric Vehicle is equipped with. The CVT can increase the overall powertrain efficiency, offering a continuum variable gear ratios between established minimum and maximum limits. This paper aims to determine the losses of a CVT, operating on a HEV. Using simulation, the losses were computed and the fuel economy was analyzed. During various modes of operation, such as electric, regenerative braking, engine charge for maintaining the battery state of charge, the losses and their dependence with the control properties were analyzed. A relevant determination of precise losses is able to reduce them by using appropriate materials for their components and fluids, more efficient technical manufacturing and usage solutions and innovative control strategy.

Drivability Improvement Control for Vehicle Start-Up Applied to an Automated Manual Transmission

Directory of Open Access Journals (Sweden)

Danna Jiang

2017-01-01

Full Text Available Drivability is the key factor for the automated manual transmission. It includes fast response to the driver’s demand and the driving comfort. This paper deals with a control methodology applied to an automated manual transmission vehicle for drivability enhancement during vehicle start-up phase. Based on a piecewise model of powertrain, a multiple-model predictive controller (mMPC is designed with the engine speed, clutch disc speed, and wheel speed as the measurable input variables and the engine torque reference and clutch friction torque reference as the controller’s output variables. The model not only includes the clutch dynamic, the flexible shaft dynamic, but also includes the actuators’ delay character. Considering the driver’s intention, a slipping speed trajectory is generated based on the acceleration pedal dynamically. The designed control strategy is verified on a complete powertrain and longitudinal vehicle dynamic model with different driver’s torque demands.

A free-piston Stirling engine/linear alternator controls and load interaction test facility

Science.gov (United States)

Rauch, Jeffrey S.; Kankam, M. David; Santiago, Walter; Madi, Frank J.

1992-01-01

A test facility at LeRC was assembled for evaluating free-piston Stirling engine/linear alternator control options, and interaction with various electrical loads. This facility is based on a 'SPIKE' engine/alternator. The engine/alternator, a multi-purpose load system, a digital computer based load and facility control, and a data acquisition system with both steady-periodic and transient capability are described. Preliminary steady-periodic results are included for several operating modes of a digital AC parasitic load control. Preliminary results on the transient response to switching a resistive AC user load are discussed.

A novel transient wall heat transfer approach for the start-up of SI engines with gasoline direct injection

Science.gov (United States)

Lejsek, David; Kulzer, André; Hammer, Jürgen

2010-11-01

The introduction of CO2-reduction technologies like Start-Stop or the Hybrid-Powertrain and the worldwide stringent emission legislation require a detailed optimization of the engine start-up. The combustion concept development as well as the calibration of the engine control unit makes an explicit thermodynamic analysis of the combustion process during the start-up necessary. Initially, the well-known thermodynamic analysis of in-cylinder pressure at stationary condition was transmitted to the highly non-stationary engine start-up. For this running mode of the engine the current models for calculation of the transient wall heat fluxes were found to be misleading. With a fraction of nearly 45% of the burned fuel energy, the wall heat is very important for the calculation of energy balance and for the combustion process analysis. Based on the measurements of transient wall heat transfer densities during the start-up presented in a former work (Lejsek and Kulzer in Investigations on the transient wall heat transfer at start-up for SI engines with gasoline direct injection. SAE Paper), the paper describes the development of adaptations to the known correlations by Woschni (MTZ 31:491, 1970), Hohenberg (Experimentelle Erfassung der Wandwärme von Kolbenmotoren. TU Graz, Habil., 1980) and Bargende (Ein Gleichungsansatz zur Berechnung der instationären Wandwärmeverluste im Hochdruckteil von Ottomotoren. TH Darmstadt, PhD-Thesis, 1991) for the application during engine start-up. To demonstrate the high accuracy of the model, the results of the cyclic resolved thermodynamic analysis using the presented novel approaches were compared with the results of the measurements. It is shown, that the novel heat flux models for the engine start-up process gives a cyclic resolved thermodynamic analysis to optimize the engine start-up pretty efficient.

Data on test results of vessel cooling system of high temperature engineering test reactor

International Nuclear Information System (INIS)

Saikusa, Akio; Nakagawa, Shigeaki; Fujimoto, Nozomu; Tachibana, Yukio; Iyoku, Tatsuo

2003-02-01

High Temperature Engineering Test Reactor (HTTR) is the first graphite-moderated helium gas cooled reactor in Japan. The rise-to-power test of the HTTR started on September 28, 1999 and thermal power of the HTTR reached its full power of 30 MW on December 7, 2001. Vessel Cooling System (VCS) of the HTTR is the first Reactor Cavity Cooling System (RCCS) applied for High Temperature Gas Cooled Reactors. The VCS cools the core indirectly through the reactor pressure vessel to keep core integrity during the loss of core flow accidents such as depressurization accident. Minimum heat removal of the VCS to satisfy its safety requirement is 0.3MW at 30 MW power operation. Through the performance test of the VCS in the rise-to-power test of the HTTR, it was confirmed that the VCS heat removal at 30 MW power operation was higher than 0.3 MW. This paper shows outline of the VCS and test results on the VCS performance. (author)

Air Force Research Laboratory's Rocket Engine Program Enters Fast-Paced Test Phase

National Research Council Canada - National Science Library

Thornburg, Jeff

2002-01-01

.... Recent tests of the Integrated Powerhead Demonstration project here established a technical first for the United States and mark the first advancements in boost engine technology since the space...

Autonomous Cryogenic Load Operations: Knowledge-Based Autonomous Test Engineer

Science.gov (United States)

Schrading, J. Nicolas

2013-01-01

The Knowledge-Based Autonomous Test Engineer (KATE) program has a long history at KSC. Now a part of the Autonomous Cryogenic Load Operations (ACLO) mission, this software system has been sporadically developed over the past 20 years. Originally designed to provide health and status monitoring for a simple water-based fluid system, it was proven to be a capable autonomous test engineer for determining sources of failure in the system. As part of a new goal to provide this same anomaly-detection capability for a complicated cryogenic fluid system, software engineers, physicists, interns and KATE experts are working to upgrade the software capabilities and graphical user interface. Much progress was made during this effort to improve KATE. A display of the entire cryogenic system's graph, with nodes for components and edges for their connections, was added to the KATE software. A searching functionality was added to the new graph display, so that users could easily center their screen on specific components. The GUI was also modified so that it displayed information relevant to the new project goals. In addition, work began on adding new pneumatic and electronic subsystems into the KATE knowledge base, so that it could provide health and status monitoring for those systems. Finally, many fixes for bugs, memory leaks, and memory errors were implemented and the system was moved into a state in which it could be presented to stakeholders. Overall, the KATE system was improved and necessary additional features were added so that a presentation of the program and its functionality in the next few months would be a success.

Definitive design status of the SP-100 Ground Engineering System Test Site

International Nuclear Information System (INIS)

Renkey, E.J. Jr.; Bazinet, G.D.; Bitten, E.J.; Brackenbury, P.J.; Carlson, W.F.; Irwin, J.J.; Edwards, P.A.; Shen, E.J.; Titzler, P.A.

1989-05-01

The SP-100 reactor will be ground tested at the SP-100 Ground Engineering System (GES) Test Site on the US Department of Energy (DOE) Hanford Site near Richland, Washington. Project direction and the flight system design evolution have resulted in a smaller reactor size and the consequential revision to Test Site features to accommodate the design changes and reduce Test Site costs. The significant design events since the completion of the Conceptual Design are discussed in this paper

Definitive design status of the SP-100 Ground Engineering System Test Site

Energy Technology Data Exchange (ETDEWEB)

Renkey, E.J. Jr.; Bazinet, G.D.; Bitten, E.J.; Brackenbury, P.J.; Carlson, W.F.; Irwin, J.J.; Edwards, P.A.; Shen, E.J.; Titzler, P.A.

1989-05-01

The SP-100 reactor will be ground tested at the SP-100 Ground Engineering System (GES) Test Site on the US Department of Energy (DOE) Hanford Site near Richland, Washington. Project direction and the flight system design evolution have resulted in a smaller reactor size and the consequential revision to Test Site features to accommodate the design changes and reduce Test Site costs. The significant design events since the completion of the Conceptual Design are discussed in this paper.

JANNAF "Test and Evaluation Guidelines for Liquid Rocket Engines": Status and Application

Science.gov (United States)

Parkinson, Douglas; VanLerberghe, Wayne M.; Rahman, Shamim A.

2017-01-01

For many decades, the U.S. rocket propulsion industrial base has performed remarkably in developing complex liquid rocket engines that can propel critical payloads into service for the nation, as well as transport people and hardware for missions that open the frontiers of space exploration for humanity. This has been possible only at considerable expense given the lack of detailed guidance that captures the essence of successful practices and knowledge accumulated over five decades of liquid rocket engine development. In an effort to provide benchmarks and guidance for the next generation of rocket engineers, the Joint Army Navy NASA Air Force (JANNAF) Interagency Propulsion Committee published a liquid rocket engine (LRE) test and evaluation (T&E) guideline document in 2012 focusing on the development challenges and test verification considerations for liquid rocket engine systems. This document has been well received and applied by many current LRE developers as a benchmark and guidance tool, both for government-driven applications as well as for fully commercial ventures. The USAF Space and Missile Systems Center (SMC) has taken an additional near-term step and is directing activity to adapt and augment the content from the JANNAF LRE T&E guideline into a standard for potential application to future USAF requests for proposals for LRE development initiatives and launch vehicles for national security missions. A draft of this standard was already sent out for review and comment, and is intended to be formally approved and released towards the end of 2017. The acceptance and use of the LRE T&E guideline is possible through broad government and industry participation in the JANNAF liquid propulsion committee and associated panels. The sponsoring JANNAF community is expanding upon this initial baseline version and delving into further critical development aspects of liquid rocket propulsion testing at the integrated stage level as well as engine component level, in

40 CFR 1042.505 - Testing engines using discrete-mode or ramped-modal duty cycles.

Science.gov (United States)

2010-07-01

... ramped-modal duty cycles. 1042.505 Section 1042.505 Protection of Environment ENVIRONMENTAL PROTECTION... duty cycles. This section describes how to test engines under steady-state conditions. In some cases, we allow you to choose the appropriate steady-state duty cycle for an engine. In these cases, you...

Analyzing Real-World Light Duty Vehicle Efficiency Benefits

Energy Technology Data Exchange (ETDEWEB)

Gonder, Jeffrey; Wood, Eric; Chaney, Larry; Holden, Jacob; Jeffers, Matthew; Wang, Lijuan

2016-06-08

Off-cycle technologies represent an important pathway to achieve real-world fuel savings, through which OEMs can potentially receive credit toward CAFE compliance. DOE national labs such as NREL are well positioned to provide objective input on these technologies using large, national data sets in conjunction with OEM- and technology-specific testing. This project demonstrates an approach that combines vehicle testing (dynamometer and on-road) with powertrain modeling and simulation over large, representative datasets to quantify real-world fuel economy. The approach can be applied to specific off-cycle technologies (engine encapsulation, start/stop, connected vehicle, etc.) in A/B comparisons to support calculation of realistic real-world impacts. Future work will focus on testing-based A/B technology comparisons that demonstrate the significance of this approach.

The Role of Alternative Testing Strategies in Environmental Risk Assessment of Engineered Nanomaterials

OpenAIRE

Hjorth, Rune; Holden, Patricia; Hansen, Steffen Foss; Colman, Ben; Grieger, Khara; Hendren, Christine

2017-01-01

Within toxicology there is a pressure to find new test systems and organisms to replace, reduce and refine animal testing. In nanoecotoxicology the need for alternative testing strategies (ATS) is further emphasized as the validity of tests and risk assessment practices developed for dissolved chemicals are challenged. Nonetheless, standardized whole organism animal testing is still considered the gold standard for environmental risk assessment. Advancing risk analysis of engineered nanomater...

Dynamic material characterization by combining ballistic testing and an engineering model

NARCIS (Netherlands)

Carton, E.P.; Roebroeks, G.H.J.J.; Wal, R. van der

2013-01-01

At TNO several energy-based engineering models have been created for various failure mechanism occurring in ballistic testing of materials, like ductile hole growth, denting, plugging, etc. Such models are also under development for ceramic and fiberbased materials (fabrics). As the models are

ARC Research Areas and Projects

Science.gov (United States)

studying realistic engine-in-vehicle operation, thermal management, component matching, advanced powertrain maximize the vehicle's performance. The vision of Thrust Area 1 is to create adaptive vehicles for maximum , victor.j.paul2.civ@mail.mil The safety and performance of human occupants and operators are paramount in the

Development and Testing of a Rotating Detonation Engine Run on Hydrogen and Air

Science.gov (United States)

2012-03-22

Jay Rutledge (Member) Date v AFIT/GAE/ENY/12-M36 Abstract Rotating detonation engines ( RDEs ) have the potential for greater...efficiencies over conventional engines by utilizing pressure gain combustion. A new modular RDE (6 in diameter) was developed and successfully run on...hydrogen and standard air. The RDE allows for variation of injection scheme and detonation channel widths. Tests provided the operational space of the

Test results of pongamia pinnata methyl esters with direct injection diesel engine

International Nuclear Information System (INIS)

Bannikov, MG.; Chattha, J.A.; Khan, A.F.

2011-01-01

Pongamia Pinnata oil is considered as a potential source of biodiesel production in Pakistan. When selecting source for commercial production of biodiesel several criteria are used. One of them is that biodiesel or biodiesel/diesel fuel blends must provide satisfactory performance and emissions of the diesel engine without or with a little engine modification. In this research performance and emissions characteristics of a direct injection diesel engine running on Pongamia Pinnata methyl esters were discussed. Discussion was supported by an analysis of combustion characteristics derived from in-cylinder pressure data. Engine running on a neat biodiesel showed higher brake specific fuel consumption and lower brake fuel conversion efficiency at all loads, whereas emissions were improved except of carbon monoxide emission at high loads. Decrease in brake efficiency and reduction of nitrogen oxides emissions were attributed solely to the change in the rate of heat release. Deposits on fuel infector nozzle were observed when engine was running on the neat biodiesel. Based on test results conclusion was made that Pongamia biodiesel/diesel fuel blends can effectively be used as a diesel oil substitute. (author)

Magnetohydrodynamics (MHD) Engineering Test Facility (ETF) 200 MWe power plant. Conceptual Design Engineering Report (CDER). Volume 2: Engineering. Volume 3: Costs and schedules

Science.gov (United States)

1981-01-01

Engineering design details for the principal systems, system operating modes, site facilities, and structures of an engineering test facility (ETF) of a 200 MWE power plant are presented. The ETF resembles a coal-fired steam power plant in many ways. It is analogous to a conventional plant which has had the coal combustor replaced with the MHD power train. Most of the ETF components are conventional. They can, however, be sized or configured differently or perform additional functions from those in a conventional coal power plant. The boiler not only generates steam, but also performs the functions of heating the MHD oxidant, recovering seed, and controlling emissions.

A reliability as an independent variable (RAIV) methodology for optimizing test planning for liquid rocket engines