On-road emission characteristics of CNG-fueled bi-fuel taxis

Science.gov (United States)

Yao, Zhiliang; Cao, Xinyue; Shen, Xianbao; Zhang, Yingzhi; Wang, Xintong; He, Kebin

2014-09-01

To alleviate air pollution and lessen the petroleum demand from the motor vehicle sector in China, natural gas vehicles (NGVs) have been rapidly developed over the last several years. However, the understanding of the real-world emissions of NGVs is very limited. In this study, the emissions from 20 compressed-natural-gas-fueled bi-fuel taxis were measured using a portable emission measurement system (PEMS) under actual driving conditions in Yichang, China. The emission characteristics of the tested vehicles were analyzed, revealing that the average CO2, CO, HC and NOx emissions from the tested compressed-natural-gas (CNG) taxis under urban driving conditions were 1.6, 4.0, 2.0 and 0.98 times those under highway road conditions, respectively. The CO, HC and NOx emissions from Euro 3 CNG vehicles were approximately 40%, 55% and 44% lower than those from Euro 2 vehicles, respectively. Compared with the values for light-duty gasoline vehicles reported in the literature, the CO2 and CO emissions from the tested CNG taxis were clearly lower; however, significant increases in the HC and NOx emissions were observed. Finally, we normalized the emissions under the actual driving cycles of the entire test route to the New European Driving Cycle (NEDC)-based emissions using a VSP modes method developed by North Carolina State University. The simulated NEDC-based CO emissions from the tested CNG taxis were better than the corresponding emissions standards, whereas the simulated NEDC-based HC and NOx emissions greatly exceeded the standards. Thus, more attention should be paid to the emissions from CNG vehicles. As for the CNG-fueled bi-fuel taxis currently in use, the department of environmental protection should strengthen their inspection and supervision to reduce the emissions from these vehicles. The results of this study will be helpful in understanding and controlling emissions from CNG-fueled bi-fuel vehicles in China.

Driving environment in Iran increases blood pressure even in healthy taxi drivers

Directory of Open Access Journals (Sweden)

Soodabeh Navadeh Khodadadi

2008-12-01

Full Text Available

• BACKGROUND: Nowadays, driving is an unseparated part of our new modern lifestyle; and we are exposed to this environment all the days for several hours whether as drivers or as riders. Many reports indicated that Iran is on the top rank of automobile-related morbidity and mortality among developed and even many developing countries that can be due to dangerous driving habits in Iran. We designed this study to find out if environment of driving have clinically important effects on blood pressure (BP and how strong is the effect. We also examined if there were any predictors for the BP rises in driving time.
• METHODS: In a cross-sectional study, 31 healthy male taxi drivers were included through a multistage proportional sampling method in winter and spring 2007. They were referred to the clinic of hypertension in Shafa Hospital, Kerman. A trained nurse measured the BPs. She also did set up the Ambulatory Blood Pressure Monitor (ABPM on the drivers’ left arms for BP recording every 30 minutes during the day. Based on the diurnal recorded BPs, the subjects were allocated into normotensive and hypertensive (systolic BP > 135 or diastolic BP > 85mmHg groups. The difference among the clinic BPs and the driving BPs was examined by t-test in Stata version 8, followed by a multivariate analysis for exploring the main predictors for BP rises in driving time.
• RESULTS: Both mean systolic and mean diastolic BPs were significantly increased from 116.85 (SE 2.28 and 74.44 (SE 2.22 mmHg in clinic to 138.64 (SE 2.77 and 95.70 (SE 2.55 mmHg during driving, respectively (P = 0.0001. Pulse pressure remained constant (P = 0.87. The difference between clinic's and driving time measurements was higher in hypertensive group. Those with higher systolic blood pressures in clinic had more frequent and higher BP rises in driving time (P = 0.02.
• CONCLUSIONS: Driving

• Transcendence, Taxis, Trust: Richard Kearney and Jacques Derrida

  Directory of Open Access Journals (Sweden)

  Ulrich Schmiedel

  2017-03-01

  Full Text Available Whatever else it takes to drive a taxi, it takes trust. Day after day, the driver has to decide whether the other is or is not trustworthy. I take the taxi as a test case to analyze and assess Richard Kearney’s diacritical hermeneutics of the other. I argue that Kearney functionalizes the concept of transcendence in order to connect the transcendence of the finite other to the transcendence of the infinite other. However, in his central critique of the deconstructionists following Jacques Derrida, Kearney counters his connection. While Kearney’s critique of Derrida’s account of absolute alterity is correct and compelling, I argue that Derrida’s critique of a distinction between the trustworthy other and the non-trustworthy other might be more crucial than Kearney contends. Insisting on openness to the other’s otherness, Derrida provokes any hermeneutic of the other to trust in transcendence. The taxi is taken as a test to illustrate the implications which diacritical and deconstructive drivers might have for evaluating the entanglement of ethics and eschatology—inside and outside the taxi.

• A cross-sectional study with an improved methodology to assess occupational air pollution exposure and respiratory health in motorcycle taxi driving

  International Nuclear Information System (INIS)

  Lawin, Herve; Agodokpessi, Gildas; Ayelo, Paul; Kagima, Jacqueline; Sonoukon, Rodrigue; Mbatchou Ngahane, Bertrand H.; Awopeju, Olayemi; Vollmer, William M.; Nemery, Benoit; Burney, Peter; Fayomi, Benjamin

  2016-01-01

  Introduction: Motorcycle taxi driving is common in many African cities. This study tested whether this occupation is associated with more respiratory disorders in a context of widespread urban air pollution with an improved methodology. Methods: In a cross sectional study we compared 85 male motorcycle taxi drivers in the capital city of the Republic of Benin (Cotonou) with an age and neighborhood matched control group. All participants carried a portable carbon monoxide data logger for 8 hours per day to assess exposure to air pollution. Respiratory symptoms were obtained using a standardized questionnaire and pulmonary function was assessed by spirometry. Results: The two groups did not differ significantly (p > 0.10) in their age, height, educational level, and exposures to smoke from biomass fuels and tobacco products. The taxi drivers were exposed to higher mean (SD) levels of carbon monoxide (7.6 ± 4.9 ppmvs. 5.4 ± 3.8 ppm p = 0.001). They reported more phlegm and tended to have slightly lower levels of lung function, although these differences were not statistically significant. Conclusion: In this cross sectional study of young motorcycle taxi drivers with substantial exposure to urban traffic and a matched control group, we found no evidence for respiratory impairment. A follow-up of such study population with other pollution exposure surrogate and other clinical endpoint may provide a more robust conclusion regarding the exposure response in this professional group. - Highlights: • Need of improved study method to assess air pollution effect in exposed workers • This study compared motorcycle taxi drivers and a matched control group • Personal carbon monoxide exposure and respiratory disorders were collected • No evidence of more respiratory disorders even though pollutant exposure was higher

• A cross-sectional study with an improved methodology to assess occupational air pollution exposure and respiratory health in motorcycle taxi driving

  Energy Technology Data Exchange (ETDEWEB)

  Lawin, Herve, E-mail: hervelawin@yahoo.fr [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin); Agodokpessi, Gildas [Centre National Hospitalier et Universitaire de Pneumo-Phtisiologie, Cotonou (Benin); Ayelo, Paul [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin); Kagima, Jacqueline [Department of internal medicine, Egerton University (Kenya); Sonoukon, Rodrigue [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin); Mbatchou Ngahane, Bertrand H. [Department of Internal Medicine, Douala General Hospital, Cameroon Faculty of Medicine and Pharmaceutical Sciences, University of Douala, Douala (Cameroon); Awopeju, Olayemi [Department of Medicine, Obafemi Awolowo University, Ile Ife (Nigeria); Vollmer, William M. [Center for Health Research, Kaiser Permanente Northwest, Portland (United States); Nemery, Benoit [Dept. of Public Health, Occupational and Environmental Insurance Medicine, KU Leuven, Leuven (Belgium); Burney, Peter [National Heart & Lung Institute, Imperial College, London (United Kingdom); Fayomi, Benjamin [Unit of Teaching and Research in Occupational and Environmental Health, Department of Public Health, Faculty of Health Sciences, University of Abomey-Calavi (Benin)

  2016-04-15

  Introduction: Motorcycle taxi driving is common in many African cities. This study tested whether this occupation is associated with more respiratory disorders in a context of widespread urban air pollution with an improved methodology. Methods: In a cross sectional study we compared 85 male motorcycle taxi drivers in the capital city of the Republic of Benin (Cotonou) with an age and neighborhood matched control group. All participants carried a portable carbon monoxide data logger for 8 hours per day to assess exposure to air pollution. Respiratory symptoms were obtained using a standardized questionnaire and pulmonary function was assessed by spirometry. Results: The two groups did not differ significantly (p > 0.10) in their age, height, educational level, and exposures to smoke from biomass fuels and tobacco products. The taxi drivers were exposed to higher mean (SD) levels of carbon monoxide (7.6 ± 4.9 ppmvs. 5.4 ± 3.8 ppm p = 0.001). They reported more phlegm and tended to have slightly lower levels of lung function, although these differences were not statistically significant. Conclusion: In this cross sectional study of young motorcycle taxi drivers with substantial exposure to urban traffic and a matched control group, we found no evidence for respiratory impairment. A follow-up of such study population with other pollution exposure surrogate and other clinical endpoint may provide a more robust conclusion regarding the exposure response in this professional group. - Highlights: • Need of improved study method to assess air pollution effect in exposed workers • This study compared motorcycle taxi drivers and a matched control group • Personal carbon monoxide exposure and respiratory disorders were collected • No evidence of more respiratory disorders even though pollutant exposure was higher.

• Taxis and crowd-taxis: sharing as a private activity and public concern

  Directory of Open Access Journals (Sweden)

  Merethe Dotterud Leiren

  2016-06-01

  Full Text Available The sharing economy has generated interest among economists for its customer focus and potential to enhance competition. However, it has also caused uproar in industries which have felt competitive pressure, for example among the established stakeholders in the taxi industry. While regulations currently impose considerable costs on the taxi industry, they do not cover virtual transport innovations such as Uber. The lack of a level playing field between taxis and such ‘crowd-taxis’ has generated media attention and conflict. Taxi owners worry about decreasing revenues and taxi drivers about poor working conditions. Other concerns are related to poor transport preparedness, accessibility issues, quality assurance and tax evasion. Despite considerable media attention, there has so far been a lack of scholarly literature addressing the consequences of the sharing economy in the transport sector. Focusing on the Norwegian taxi market, we argue that crowd-taxis will likely produce a range of unanticipated effects, necessitating regulation. For example, crowd-taxis may contribute to a loss of transport preparedness in rural areas. The findings are based on first and secondary data and 19 interviews.

• Autonomous vehicles are cost-effective when used as taxis.

  Science.gov (United States)

  Freedman, Isaac G; Kim, Ellen; Muennig, Peter A

  2018-06-04

  Autonomous vehicles (AVs) will radically re-shape the health and well-being of people in the United States in good ways and bad. We set out to estimate a reasonable time-to-adoption using cost-effectivenessmodels to estimate the point at which AVs become reasonably safe and affordable for widespread adoption. We used Waymo data (previously, Google Self-Driving Car Project) and a microsimulation model to explore projected costs and safety issues today and five years from today to get a sense of the speed of consumer adoption were AVs brought to the market. The adoption of AVs for private use was associated with an ICER of 1,396,110/QALY gained today, a figure that would decline to 173,890/QALY gained 5-years in the future. However, AV taxis are both less expensive and potentially already safer than human-piloted taxis. While AVs are not unlikely to be used a family vehicles any time soon, it would make economic sense to adopt them as taxis today. Legislation enhancing the benefits while mitigating the potential harmful health impacts of AV taxis is needed with some urgency.

• Estimation of occupational and nonoccupational nitrogen dioxide exposure for Korean taxi drivers using a microenvironmental model

  International Nuclear Information System (INIS)

  Son, Busoon; Yang, Wonho; Breysse, Patrick; Chung, Taewoong; Lee, Youngshin

  2004-01-01

  Occupational and nonoccupational personal nitrogen dioxide (NO 2 ) exposures were measured using passive samplers for 31 taxi drivers in Asan and Chunan, Korea. Exposures were also estimated using a microenvironmental time-weighted average model based on indoor, outdoor and inside the taxi area measurements. Mean NO 2 indoor and outdoor concentrations inside and outside the taxi drivers' houses were 24.7±10.7 and 23.3±8.3 ppb, respectively, with a mean indoor to outdoor NO 2 ratio of 1.1. Mean personal NO 2 exposure of taxi drivers was 30.3±9.7 ppb. Personal NO 2 exposures for drivers were more strongly correlated with interior vehicle NO 2 levels (r=0.89) rather than indoor residential NO 2 levels (r=0.74) or outdoor NO 2 levels (r=0.71). The main source of NO 2 exposure for taxi drivers was considered to be occupational driving. Interestingly, the NO 2 exposures for drivers' using LPG-fueled vehicles (26.3±1.3 ppb) were significantly lower than those (38.1±1.3 ppb) using diesel-fueled vehicle (P 2 exposure with indoor and outdoor NO 2 levels of the residence, and interior vehicle NO 2 levels (P 2 levels because they drive diesel-using vehicles outdoors in Korea

• Hematocrit levels as cardiovascular risk among taxi drivers in Bangkok, Thailand

  Science.gov (United States)

  ISHIMARU, Tomohiro; ARPHORN, Sara; JIRAPONGSUWAN, Ann

  2016-01-01

  In Thailand, taxi drivers employed in the informal sector often experience hazardous working conditions. Previous studies revealed that elevated Hematocrit (HCT) is a predictor of cardiovascular disease (CVD) risk. This study assessed factors associated with HCT in taxi drivers to predict their occupational CVD risk factors. A cross-sectional study was conducted on 298 male taxi drivers who joined a health check-up campaign in Bangkok, Thailand. HCT and body mass index were retrieved from participant health check-up files. Self-administered questionnaires assessed demographics, driving mileage, working hours, and lifestyle. Statistical associations were analyzed using stepwise linear regression. Our results showed that obesity (p=0.007), daily alcohol drinking (p=0.003), and current or past smoking (p=0.016) were associated with higher HCT levels. While working hours were not directly associated with HCT levels in the current study, the effect on overworking is statistically arguable because most participants worked substantially longer hours. Our findings suggest that taxi drivers’ CVD risk may be increased by their unhealthy work styles. Initiatives to improve general working conditions for taxi drivers should take into account health promotion and CVD prevention. The policy of providing periodic health check-ups is important to make workers in the informal sector aware of their health status. PMID:27151439

• Assessing and reducing fine and ultrafine particles inside Los Angeles taxis

  Science.gov (United States)

  Yu, Nu; Shu, Shi; Lin, Yan; Zhu, Yifang

  2018-05-01

  Taxi drivers and passengers are exposed to high levels of traffic-related air pollutants, but their exposures to fine (PM2.5) and ultrafine particles (UFPs) and related mitigation strategies are rarely explored. In this study, UFP and PM2.5 concentrations were monitored concurrently inside and outside of 22 taxis under different ventilation and mitigation conditions. Under realistic working conditions (no mitigation; NM), the average UFP and PM2.5 levels inside taxis were 1.46 × 104 particles/cm3 and 26 μg/m3, respectively. When the taxi ventilation was set to outside air mode and the windows kept closed, in-cabin UFP and PM2.5 concentrations are significantly associated with on-road concentrations, driving speed, and cabin air filter usage. The average in-cabin to on-roadway (I/O) ratios for UFP and PM2.5 were reduced from 0.60 to 0.75 under NM, to 0.47 and 0.52 under the most stringent mitigation strategy of keeping the windows closed and operating a high efficiency cabin air filter (WC + HECA). Among all tested taxi models, Toyota Prius exhibited the lowest UFP and PM2.5 I/O ratios under WC + HECA. Switching cabin air filters from the originally equipped manufacturer filter (OEM) to a HECA filter reduced the UFP and PM2.5 I/O ratios most effectively in Toyota Prius taxis as well.

• Toronto hybrid taxi pilot

  International Nuclear Information System (INIS)

  Stevens, M.; Marans, B.

  2009-10-01

  This paper provided details of a hybrid taxi pilot program conducted to compare the on-road performance of Toyota Camry hybrid vehicles against conventional vehicles over a 1-year period in order to determine the business case and air emission reductions associated with the use of hybrid taxi cabs. Over 750,000 km worth of fuel consumption was captured from 10 Toyota Camry hybrids, a Toyota Prius, and 5 non-hybrid Camry vehicles over an 18-month period. The average real world fuel consumption for the taxis demonstrated that the Toyota Prius has the lowest cost of ownership, while the non-hybrid Camry has the highest cost of ownership. Carbon dioxide (CO 2 ) reductions associated with the 10 Camry hybrid taxis were calculated at 236 tonnes over a 7-year taxi service life. Results suggested that the conversion of Toronto's 5680 taxis would yield annual CO 2 emission reductions of over 19,000 tonnes. All hybrid purchasers identified themselves as highly likely to purchase a hybrid again. 5 tabs., 9 figs.

• Toronto hybrid taxi pilot

  Energy Technology Data Exchange (ETDEWEB)

  Stevens, M. [CrossChasm Technologies, Cambridge, ON (Canada); Marans, B. [Toronto Atmospheric Fund, ON (Canada)

  2009-10-15

  This paper provided details of a hybrid taxi pilot program conducted to compare the on-road performance of Toyota Camry hybrid vehicles against conventional vehicles over a 1-year period in order to determine the business case and air emission reductions associated with the use of hybrid taxi cabs. Over 750,000 km worth of fuel consumption was captured from 10 Toyota Camry hybrids, a Toyota Prius, and 5 non-hybrid Camry vehicles over an 18-month period. The average real world fuel consumption for the taxis demonstrated that the Toyota Prius has the lowest cost of ownership, while the non-hybrid Camry has the highest cost of ownership. Carbon dioxide (CO{sub 2}) reductions associated with the 10 Camry hybrid taxis were calculated at 236 tonnes over a 7-year taxi service life. Results suggested that the conversion of Toronto's 5680 taxis would yield annual CO{sub 2} emission reductions of over 19,000 tonnes. All hybrid purchasers identified themselves as highly likely to purchase a hybrid again. 5 tabs., 9 figs.

• Cost, Energy, and Environmental Impact of Automated Electric Taxi Fleets in Manhattan.

  Science.gov (United States)

  Bauer, Gordon S; Greenblatt, Jeffery B; Gerke, Brian F

  2018-04-17

  Shared automated electric vehicles (SAEVs) hold great promise for improving transportation access in urban centers while drastically reducing transportation-related energy consumption and air pollution. Using taxi-trip data from New York City, we develop an agent-based model to predict the battery range and charging infrastructure requirements of a fleet of SAEVs operating on Manhattan Island. We also develop a model to estimate the cost and environmental impact of providing service and perform extensive sensitivity analysis to test the robustness of our predictions. We estimate that costs will be lowest with a battery range of 50-90 mi, with either 66 chargers per square mile, rated at 11 kW or 44 chargers per square mile, rated at 22 kW. We estimate that the cost of service provided by such an SAEV fleet will be $0.29-$0.61 per revenue mile, an order of magnitude lower than the cost of service of present-day Manhattan taxis and $0.05-$0.08/mi lower than that of an automated fleet composed of any currently available hybrid or internal combustion engine vehicle (ICEV). We estimate that such an SAEV fleet drawing power from the current NYC power grid would reduce GHG emissions by 73% and energy consumption by 58% compared to an automated fleet of ICEVs.

• Motorcycle safety among motorcycle taxi drivers and nonoccupational motorcyclists in developing countries: A case study of Maoming, South China.

  Science.gov (United States)

  Wu, Connor Y H; Loo, Becky P Y

  2016-01-01

  An increasing number of motorcycle taxis have been involved in traffic crashes in many developing countries. This study examines the characteristics of both motorcycle taxi drivers and nonoccupational motorcyclists, investigates the risks they pose to road safety, and provides recommendations to minimize their risks. Based on the data collected from a questionnaire survey of 867 motorcycle taxi drivers and 2,029 nonoccupational motorcyclists in Maoming, South China, comparisons were made to analyze differences of personal attributes, attitudes toward road safety, and self-reported behavior of the 2 groups. Results of the chi-square tests show that not only motorcycle taxi drivers but also nonoccupational motorcyclists in Maoming held poor attitudes toward road safety and both groups reported unsafe driving behavior. There is much room for improving local road safety education among all motorcyclists in Maoming. Yet, motorcycle taxi drivers were more likely to pose road safety risks than nonoccupational motorcyclists under some circumstances, such as speeding late at night or early in the morning, not requiring passengers to wear helmets, and running a red light. The results of the binary logistic regression model show that possessing a vehicle license for a motorcycle or not was the common significant predictor for unsafe driving behavior of motorcycle taxi drivers and nonoccupational motorcyclists. Therefore, enforcement against all motorcyclists not showing vehicle licenses for their motorcycles should be stepped up. Motorcycle safety is largely poor in Maoming. Therefore, efforts to improve motorcycle safety should be strengthened by targeting not only motorcycle taxi drivers but also nonoccupational motorcyclists.

• Prevalence and factors associated with road traffic crash among taxi drivers in Hanoi, Vietnam.

  Science.gov (United States)

  La, Quang Ngoc; Lee, Andy H; Meuleners, Lynn B; Van Duong, Dat

  2013-01-01

  Injury due to road traffic crash is a major cause of ill health and premature deaths in developing countries. Taxis provide a main mode of public transport in Vietnam but there has been little research on the risk of crash for taxi drivers. This retrospective study collected information on taxi crashes for the period 2006-2009 by interviewing drivers from five taxi companies in Hanoi, Vietnam, using a structured questionnaire. Of the total 1214 participants recruited, 276 drivers reported at least one crash, giving an overall crash prevalence of 22.7%. Among the crashed group, 50 drivers (18.1%) were involved in two to four crashes. Logistic regression analysis further identified age of driver, type of driving licence, employment status, perceived sufficiency of income, seat-belt usage, and traffic infringement history to be significantly associated with the crash risk. Further prospective and qualitative studies are recommended to provide detailed crash characteristics as well as behaviour and perception of taxi drivers, so that an effective intervention can be developed to improve road safety and to prevent injury of these commercial drivers. Copyright © 2012 Elsevier Ltd. All rights reserved.

• Methods for determining unimpeded aircraft taxiing time and evaluating airport taxiing performance

  Directory of Open Access Journals (Sweden)

  Yu Zhang

  2017-04-01

  Full Text Available The objective of this study is to improve the methods of determining unimpeded (nominal taxiing time, which is the reference time used for estimating taxiing delay, a widely accepted performance indicator of airport surface movement. After reviewing existing methods used widely by different air navigation service providers (ANSP, new methods relying on computer software and statistical tools, and econometrics regression models are proposed. Regression models are highly recommended because they require less detailed data and can serve the needs of general performance analysis of airport surface operations. The proposed econometrics model outperforms existing ones by introducing more explanatory variables, especially taking aircraft passing and over-passing into the considering of queue length calculation and including runway configuration, ground delay program, and weather factors. The length of the aircraft queue in the taxiway system and the interaction between queues are major contributors to long taxi-out times. The proposed method provides a consistent and more accurate method of calculating taxiing delay and it can be used for ATM-related performance analysis and international comparison.

• Reduction of particle emissions from light duty vehicles and from taxies; Reduktion af partikelelemissioner fra varebiler og taxier

  Energy Technology Data Exchange (ETDEWEB)

  Nielsen, Johan; Henriques, M.; Weibel, T.G. [TetraPlan A/S (Denmark)

  2006-11-03

  This project, 'Reduction of particle emissions from light duty vehicles and from taxies', analyses different strategies to reduce the particle emission, their effect for particle emissions, and the resulting cost for the society and for the companies. The project describes the EU regulation of emissions, the possibilities of reducing the emissions via special requirements in environmental zones and the Danish taxation of light duty vehicles. Further, the project includes interviews with owners of light duty vehicles and taxies and also with Danish producers of particle filters. The strategies analysed in the scenarios include: 1) Promotion of particle filters; 2) Shift from diesel to gasoline and; 3) Downsizing. The effects for particle emissions and for mortality are described. Further, the costs and benefits for the society and the cost for the companies are evaluated. The effects of the scenarios are analysed, both for initiatives implemented at a national level and for implementation in an environmental zone in the municipality of Copenhagen. The main results are that the socioeconomic benefits in the year 2012 are greater than the costs, if taxis and light duty vehicles have filters installed and if they are driving in the Copenhagen area. For light duty vehicles it is only profitable, if the prices of the filters fall to the price level that is expected in the future in the study. Further, the analysis shows that for light duty vehicles and taxies driving all over the country, the socioeconomic benefits achieved by installing particle filters are too small to cover the costs. The analysis shows that it is also profitable socio-economically to change from diesel to petrol for light duty vehicles and for taxies (except taxies driving nationally). The analysis is based on the producer prices including the general net tax level, while the specific taxes are not included. From the point of view of the companies it is not profitable to change to petrol

• Prevalence and factors associated with road traffic crash among taxi drivers in Mekelle town, northern Ethiopia, 2014: a cross sectional study.

  Directory of Open Access Journals (Sweden)

  Nigus Gebremedhin Asefa

  Full Text Available The 2013 World Health Organization Status Report on Road Safety estimated that approximately 1.24 million deaths occur annually due to road traffic crashes with most of the burden falling on low- and middle-income countries. The objective of this research is to study the prevalence of road traffic crashes in Mekelle, Tigray, Northern Ethiopia and to identify risk factors with the ultimate goal of informing prevention activities and policies.This study used a cross-sectional design to measure the prevalence and factors associated with road traffic crashes among 4-wheeled minibus (n = 130 and 3-wheeled Bajaj (n = 582 taxi drivers in Mekelle, Ethiopia. Bivariate and multivariate logistic regression were used to evaluate the association between risk factors and drivers' involvement in a road traffic crash within the 3 years prior to the survey.Among the 712 taxi drivers, 26.4% (n = 188 of them reported involvement in a road traffic crash within the past 3 years. Drivers who listened to mass media had decreased likelihood of road traffic crash involvement (AOR = 0.51, 0.33-0.78, while speedy driving (AOR = 4.57, 3.05-7.44, receipt of a prior traffic punishment (AOR = 4.57, 2.67-7.85, and driving a mechanically faulty taxi (AOR = 4.91, 2.81-8.61 were strongly associated with road traffic crash involvement. Receiving mobile phone calls while driving (AOR = 1.91, 1.24-2.92 and history of alcohol use (AOR = 1.51, 1.00-2.28 were also associated with higher odds of road traffic crash involvement.The results of this study show that taxi drivers in Mekelle habitually place themselves at increased risk of road traffic crashes by violating traffic laws, especially related to speedy driving, mobile phone use, and taxi maintenance. This research can be used to support re-evaluation of the type, severity, and enforcement of traffic violation penalties.

• Automation of Taxiing

  Directory of Open Access Journals (Sweden)

  Jaroslav Bursík

  2017-01-01

  Full Text Available The article focuses on the possibility of automation of taxiing, which is the part of a flight, which, under adverse weather conditions, greatly reduces the operational usability of an airport, and is the only part of a flight that has not been affected by automation, yet. Taxiing is currently handled manually by the pilot, who controls the airplane based on information from visual perception. The article primarily deals with possible ways of obtaining navigational information, and its automatic transfer to the controls. Analyzed wand assessed were currently available technologies such as computer vision, Light Detection and Ranging and Global Navigation Satellite System, which are useful for navigation and their general implementation into an airplane was designed. Obstacles to the implementation were identified, too. The result is a proposed combination of systems along with their installation into airplane’s systems so that it is possible to use the automated taxiing.

• Het CBb en 'Der digitale Taxi-Krieg'

  NARCIS (Netherlands)

  Westerveld, M.

  2015-01-01

  UberPOP, the taxi service company that claims to be based on the concept of shared economy, offering a positive effect on mobility, environment and usage of energy, in reality confronts us with the question whether we are able to protect 'on demand' workers against exploitation and underpayment. The

The application of algorithm in taxi security system

Science.gov (United States)

Luo, Chengyu

2017-08-01

With the booming of the society and economy today, Taxis and private cars have gradually become one of the most popular tools in transportation for their low price and convenience. However, because of the breakdown in the security system, a few accidents occurred due to the illegal taxi. The unreliable security management has attributed to the lack of trust in taxi companies and relevant regulatory authorities, which considered to be the reason why people are worried about it. Accordingly, we put forward a design for a taxi security system, making use of modern technology such as NFC, iBeacon, GPS combined with algorithms, automatically recognize the taxi we take, and reflecting basic information of taxi and driver on our mobile phone.

Modeling taxi driver anticipatory behavior

NARCIS (Netherlands)

Zheng, Zhong; Rasouli, S.; Timmermans, H.J.P.

2018-01-01

As part of a wider behavioral agent-based model that simulates taxi drivers’ dynamic passenger-finding behavior under uncertainty, we present a model of strategic behavior of taxi drivers in anticipation of substantial time varying demand at locations such as airports and major train stations. The

Economic Analysis on Value Chain of Taxi Fleet with Battery-Swapping Mode Using Multiobjective Genetic Algorithm

Directory of Open Access Journals (Sweden)

Guobao Ning

2012-01-01

Full Text Available This paper presents an economic analysis model on value chain of taxi fleet with battery-swapping mode in a pilot city. In the model, economic benefits of charging-swapping station group, taxi company, and taxi driver in the region have been taken into consideration. Thus, the model is a multiobjective function and multiobjective genetic algorithm is used to solve this problem. According to the real data collected from the pilot city, the multiobjective genetic algorithm is tested as an effective method to solve this problem. Furthermore, the effects of price of electricity, price of battery package, life cycle of battery package, cost of battery-swapping devices and infrastructure, and driving mileage per day on the benefits of value holders are analyzed, which provide theoretical and practical reference for the deployment of electric vehicles, for the national subsidy criteria adjusment, technological innovation instruction, commercial mode selection, and infrastructure construction.

Assessment of exposure to whole body vibration in Yazd city taxi drivers

Directory of Open Access Journals (Sweden)

F Samoori sakhvidi

2016-11-01

in the Z-axis is equal to .45 m/s2 that was more than out of the axes X, Y. (rms acceleration values in the range of potential risks to health. The average Aeq acceleration in the Pride was obtained. 62 m/s2, which was more than 2 cars, although statistically significant difference was not found between the types of vehicles. But average Aeq acceleration of the vehicle was located in the zone caution health. Average vibration dose for all vehicles were less than limits recommended in the ISO 2631 standard. The results showed that increasing the mileage and life of the car and also traffic during driving can increase exposure to vibration in the taxi drivers. Conclusion: The results suggest that taxi drivers are exposed to significant amounts of whole body vibration. Therefore, we must take measures to reduce the adverse effects of vibration on these people.

Electrical drives for direct drive renewable energy systems

CERN Document Server

Mueller, Markus

2013-01-01

Wind turbine gearboxes present major reliability issues, leading to great interest in the current development of gearless direct-drive wind energy systems. Offering high reliability, high efficiency and low maintenance, developments in these direct-drive systems point the way to the next generation of wind power, and Electrical drives for direct drive renewable energy systems is an authoritative guide to their design, development and operation. Part one outlines electrical drive technology, beginning with an overview of electrical generators for direct drive systems. Principles of electrical design for permanent magnet generators are discussed, followed by electrical, thermal and structural generator design and systems integration. A review of power electronic converter technology and power electronic converter systems for direct drive renewable energy applications is then conducted. Part two then focuses on wind and marine applications, beginning with a commercial overview of wind turbine drive systems and a...

Exploring Urban Taxi Drivers’ Activity Distribution Based on GPS Data

Directory of Open Access Journals (Sweden)

Xiaowei Hu

2014-01-01

Full Text Available With the rapid development of information communication technology and data mining technology, we can obtain taxi vehicle’s real time operation status through the large-scale taxi GPS trajectories data and explore the drivers’ activity distribution characteristics. Based on the 204 continuous hours of 3198 taxi vehicles’ operation data of Shenzhen, China, this paper analyzed the urban taxi driver’s activity distribution characteristics from different temporal and spatial levels. In the time level, we identified the difference with taxi daily operation pattern (weekday versus weekends, continuous time in one day, passengers in vehicle time, and taxi drivers’ operation frequency; in the space level, we explored the taxi driver’s searching pattern, including searching activity space distribution and the relationship between the pick-up locations and the drop-off locations. This research can be helpful for urban taxi drivers’ operation and behavior pattern identification, as well as the contribution to the geographical activity space analysis.

Agent-Based Modeling of Taxi Behavior Simulation with Probe Vehicle Data

Directory of Open Access Journals (Sweden)

Saurav Ranjit

2018-05-01

Full Text Available Taxi behavior is a spatial–temporal dynamic process involving discrete time dependent events, such as customer pick-up, customer drop-off, cruising, and parking. Simulation models, which are a simplification of a real-world system, can help understand the effects of change of such dynamic behavior. In this paper, agent-based modeling and simulation is proposed, that describes the dynamic action of an agent, i.e., taxi, governed by behavior rules and properties, which emulate the taxi behavior. Taxi behavior simulations are fundamentally done for optimizing the service level for both taxi drivers as well as passengers. Moreover, simulation techniques, as such, could be applied to another field of application as well, where obtaining real raw data are somewhat difficult due to privacy issues, such as human mobility data or call detail record data. This paper describes the development of an agent-based simulation model which is based on multiple input parameters (taxi stay point cluster; trip information (origin and destination; taxi demand information; free taxi movement; and network travel time that were derived from taxi probe GPS data. As such, agent’s parameters were mapped into grid network, and the road network, for which the grid network was used as a base for query/search/retrieval of taxi agent’s parameters, while the actual movement of taxi agents was on the road network with routing and interpolation. The results obtained from the simulated taxi agent data and real taxi data showed a significant level of similarity of different taxi behavior, such as trip generation; trip time; trip distance as well as trip occupancy, based on its distribution. As for efficient data handling, a distributed computing platform for large-scale data was used for extracting taxi agent parameter from the probe data by utilizing both spatial and non-spatial indexing technique.

A COMMUNITY STUDY OF TAXI VIOLENCE AND DISTRESS ...

African Journals Online (AJOL)

Setting & Subjects: Five hundred and four Xhosa speaking youth aged 9-20 years, from 5 primary schools in Khayelitsha; 396 attending 4 schools in close proximity to ... Those who had been in a taxi that was shot at, those who had been at a taxi rank when people were shot, and those who had seen taxi men shooting, had ...

Taxi and limousine industry in Canada

International Nuclear Information System (INIS)

Monteiro, J.; Civettini, S.

2007-01-01

Taxi and limousine service plays an important role in the movement of people within a city. In 2004, the total revenue in this industry in Canada was $1.305 billion, and an estimated 35,339 carriers served the industry. In Canada, economic and safety regulations of taxi supply were imposed in most cities during the 1930s and 1940s and continue to this date. Although the industry is regulated, the competition law also applies. The appropriateness of these regulations continues to be challenged and regulatory reforms in the major cities in Canada have concentrated their efforts on increasing the rate of services, improving the quality of vehicles and enhancing the training of taxi drivers. Indicators for the 1999-2004 period reveal that the taxi and limousine industry in Canada did not perform very well. Revenue increased by only 1.7 per cent per year and margins deteriorated by -1.78 per cent together with the operating ratio. The purpose of this paper was to examine the taxi and limousine industry in Canada. First, the structure of the industry in Canada was examined followed by a review of the economic regulation of the industry. Recent regulatory developments in Canada and in other countries were then reviewed with arguments for or against deregulation. 28 refs., 2 tabs

Research on taxi software policy based on big data

Directory of Open Access Journals (Sweden)

Feng Daoming

2017-01-01

Full Text Available Through big data analysis, statistical analysis of a large number of factors affect the establishment of the rally car index set, By establishing a mathematical model to analyze the different space-time taxi resource “to match supply and demand” degree, combined with intelligent deployment to solve the “taxi difficult” this hot social issues. This article takes Shanghai as an example, the central park, Lu Xun park, century park three areas as the object of study. From the “sky drops fast travel intelligence platform” big data, Extracted passenger demand and the number of taxi Kongshi data. Then demand and supply of taxis to establish indicators matrix, get the degree of matching supply needs of the region. Then through the big data relevant policies of each taxi company. Using the method of cluster analysis, to find the decisive role of the three aspects of the factors, using principal component analysis, compare the advantages and disadvantages of the existing company’s programs. Finally, according to the above research to develop a reasonable taxi software related policies.

Fuel Consumption and Emissions from Airport Taxi Operations

Science.gov (United States)

Jung, Yoon

2010-01-01

Developed a method to calculate fuel consumption and emissions of phases of taxi operations. Results at DFW showed that up to 18% of fuel can be saved by eliminating stop-and-go situations. Developed an energy efficient and environmentally friendly surface concept: Spot and Runway Departure Advisory (SARDA) tool. The SARDA tool has been identified as a potential candidate for a technology transfer to the FAA.

Effectiveness of clean taxi priority incentive at Amsterdam Central Station

NARCIS (Netherlands)

van der Flier, A.S.; Dam, J.; van den Hoed, R.

2017-01-01

The municipality of Amsterdam wants to have an emission free taxi sector by 2025. In order to reach that goal, the city has taken a number of measures which favour clean taxis above conventional taxis. One of these measures is an innovative priority privilege scheme at the Amsterdam Central Station

Applicative Research on Psychological Demand of Audience and the TAXI for People

Directory of Open Access Journals (Sweden)

Zhang Caixia

2015-01-01

Full Text Available Whether TAXI for People from Beijing traffic channel, the only special program customized for taxi driver in Beijing, knows about the psychological feature of the certain taxi group is an important factor that affects the development of program. Based on demand theory of psychology, this article uses the questionnaire method to find out the psychological feature and lifestyle of audience, and discusses the degree to the TAXI for People which meets the psychological demand of taxi driver audience by analysis on the program content. It is said from the research that the TAXI for People basically meets the psychological demand from taxi drivers. However, this program shall focus more on their basic needs and provide the opportunity for the audience to participate in the program and activity.

A WEB-BASED PLATFORM FOR VISUALIZING SPATIOTEMPORAL DYNAMICS OF BIG TAXI DATA

Directory of Open Access Journals (Sweden)

H. Xiong

2017-09-01

Full Text Available With more and more vehicles equipped with Global Positioning System (GPS, access to large-scale taxi trajectory data has become increasingly easy. Taxis are valuable sensors and information associated with taxi trajectory can provide unprecedented insight into many aspects of city life. But analysing these data presents many challenges. Visualization of taxi data is an efficient way to represent its distributions and structures and reveal hidden patterns in the data. However, Most of the existing visualization systems have some shortcomings. On the one hand, the passenger loading status and speed information cannot be expressed. On the other hand, mono-visualization form limits the information presentation. In view of these problems, this paper designs and implements a visualization system in which we use colour and shape to indicate passenger loading status and speed information and integrate various forms of taxi visualization. The main work as follows: 1. Pre-processing and storing the taxi data into MongoDB database. 2. Visualization of hotspots for taxi pickup points. Through DBSCAN clustering algorithm, we cluster the extracted taxi passenger’s pickup locations to produce passenger hotspots. 3. Visualizing the dynamic of taxi moving trajectory using interactive animation. We use a thinning algorithm to reduce the amount of data and design a preloading strategyto load the data smoothly. Colour and shape are used to visualize the taxi trajectory data.

a Web-Based Platform for Visualizing Spatiotemporal Dynamics of Big Taxi Data

Science.gov (United States)

Xiong, H.; Chen, L.; Gui, Z.

2017-09-01

With more and more vehicles equipped with Global Positioning System (GPS), access to large-scale taxi trajectory data has become increasingly easy. Taxis are valuable sensors and information associated with taxi trajectory can provide unprecedented insight into many aspects of city life. But analysing these data presents many challenges. Visualization of taxi data is an efficient way to represent its distributions and structures and reveal hidden patterns in the data. However, Most of the existing visualization systems have some shortcomings. On the one hand, the passenger loading status and speed information cannot be expressed. On the other hand, mono-visualization form limits the information presentation. In view of these problems, this paper designs and implements a visualization system in which we use colour and shape to indicate passenger loading status and speed information and integrate various forms of taxi visualization. The main work as follows: 1. Pre-processing and storing the taxi data into MongoDB database. 2. Visualization of hotspots for taxi pickup points. Through DBSCAN clustering algorithm, we cluster the extracted taxi passenger's pickup locations to produce passenger hotspots. 3. Visualizing the dynamic of taxi moving trajectory using interactive animation. We use a thinning algorithm to reduce the amount of data and design a preloading strategyto load the data smoothly. Colour and shape are used to visualize the taxi trajectory data.

System dynamics model of taxi management in metropolises: Economic and environmental implications for Beijing.

Science.gov (United States)

Wang, Hao; Zhang, Kai; Chen, Junhua; Wang, Zhifeng; Li, Guijun; Yang, Yuqi

2018-05-01

Taxis are an important component of urban passenger transport. Research on the daily dispatching of taxis and the utility of governmental management is important for the improvement of passenger travel, taxi driver income and environmental impacts. However, urban taxi management is a complex and dynamic system that is affected by many factors, and positive/negative feedback relationships and nonlinear interactions exist between each subsystem and variable. Therefore, conventional research methods can hardly depict its characteristics comprehensively. To bridge this gap, this paper develops a system dynamics model of urban taxi management, in which the empty-loaded rate and total demand are selected as key factors affecting taxi dispatching, and the impacts of taxi fares on driver income and travel demand are taken into account. After the validation of the model, taxi operations data derived from a prior analysis of origin-destination data of Beijing taxis are used as input for the model to simulate the taxi market in Beijing. Finally, economic and environmental implications are provided for the government to optimise policies on taxi management. Copyright © 2018 Elsevier Ltd. All rights reserved.

Optimizing Cruising Routes for Taxi Drivers Using a Spatio-Temporal Trajectory Model

Directory of Open Access Journals (Sweden)

Liang Wu

2017-11-01

Full Text Available Much of the taxi route-planning literature has focused on driver strategies for finding passengers and determining the hot spot pick-up locations using historical global positioning system (GPS trajectories of taxis based on driver experience, distance from the passenger drop-off location to the next passenger pick-up location and the waiting times at recommended locations for the next passenger. The present work, however, considers the average taxi travel speed mined from historical taxi GPS trajectory data and the allocation of cruising routes to more than one taxi driver in a small-scale region to neighboring pick-up locations. A spatio-temporal trajectory model with load balancing allocations is presented to not only explore pick-up/drop-off information but also provide taxi drivers with cruising routes to the recommended pick-up locations. In simulation experiments, our study shows that taxi drivers using cruising routes recommended by our spatio-temporal trajectory model can significantly reduce the average waiting time and travel less distance to quickly find their next passengers, and the load balancing strategy significantly alleviates road loads. These objective measures can help us better understand spatio-temporal traffic patterns and guide taxi navigation.

pH-Taxis of Biohybrid Microsystems

Science.gov (United States)

Zhuang, Jiang; Wright Carlsen, Rika; Sitti, Metin

2015-06-01

The last decade has seen an increasing number of studies developing bacteria and other cell-integrated biohybrid microsystems. However, the highly stochastic motion of these microsystems severely limits their potential use. Here, we present a method that exploits the pH sensing of flagellated bacteria to realize robust drift control of multi-bacteria propelled microrobots. Under three specifically configured pH gradients, we demonstrate that the microrobots exhibit both unidirectional and bidirectional pH-tactic behaviors, which are also observed in free-swimming bacteria. From trajectory analysis, we find that the swimming direction and speed biases are two major factors that contribute to their tactic drift motion. The motion analysis of microrobots also sheds light on the propulsion dynamics of the flagellated bacteria as bioactuators. It is expected that similar driving mechanisms are shared among pH-taxis, chemotaxis, and thermotaxis. By identifying the mechanism that drives the tactic behavior of bacteria-propelled microsystems, this study opens up an avenue towards improving the control of biohybrid microsystems. Furthermore, assuming that it is possible to tune the preferred pH of bioactuators by genetic engineering, these biohybrid microsystems could potentially be applied to sense the pH gradient induced by cancerous cells in stagnant fluids inside human body and realize targeted drug delivery.

Exploring Spatiotemporal Patterns of Long-Distance Taxi Rides in Shanghai

Directory of Open Access Journals (Sweden)

Hangbin Wu

2017-11-01

Full Text Available Floating Car Data (FCD has been analyzed for various purposes in past years. However, limited research about the behaviors of taking long-distance taxi rides has been made available. In this paper, we used data from over 12,000 taxis during a six-month period in Shanghai to analyze the spatiotemporal patterns of long-distance taxi trips. We investigated these spatiotemporal patterns by comparing them with metro usage in Shanghai, in order to determine the extent and how the suburban trains divert the passenger flow from taxis. The results identified 12 pick-up and six drop-off hotspots in Shanghai. Overall, the pick-up locations were relatively more concentrated than the drop-off locations. Temporal patterns were also revealed. Passengers on long-distance taxi rides were observed to avoid the rush hours on the street as their first priority and tried to avoid the inconvenience of interchanges on the metro lines as their second priority.

Integration of electric vehiclesin cooper atives taxi ambato. Ecuador

Directory of Open Access Journals (Sweden)

Mery Esperanza Ruiz Guajala

2015-11-01

Full Text Available The transition from combustion vehicles towards a new electrical system friendly to the environment, is a decision to be taken by carrier based on cost-benefit analysis which generates buying it, and contribute to society not only for the service they provide, but to prevent air pollution we breathe, and if we add the future energy supply, since the Ecuadorian State in 2016 will provide the whole country of this important resource. The study focuses on two parts: the first on surveys of taxi owners to describe their perception of the integration of electric vehicles, and the second in determining the economic and financial feasibility of acquiring the vehicle Nissan Leaf by the member of the cooperative taxi. The most important conclusion is that the carriers are willing to buy an electric vehicle to mitigate the emission of toxic gases, and that its decision would save 50% in annual operating costs of your vehicle.

Social optimal shifts and fares of taxi services

Energy Technology Data Exchange (ETDEWEB)

Salanova Grau, J.M.; Estrada Romeu, M.

2016-07-01

This paper presents a mathematical model for supporting the decision and policy making related to the optimal determination of shifts and fares of taxi services in a major city. The model is based on the system’s generalized cost function and uses continuous approximations and geometric probabilities for estimating the key performance indicators of the taxi market, which are waiting and access time for the customers (in-vehicle travel time does not depend on the offer side) and benefits for the drivers. The model is based on an econometric model with the inclusion of an elastic demand, which allows the estimation of the optimal values for the two decision variables of the problem: fare structure and the taxi fleet size. The model also accounts for a full-day time period instead of the one-hour time frame models used in most of the taxi models, which allows for providing insights on the daily duration and distribution of the shifts that should be defined by the policy makers. (Author)

Uncovering urban human mobility from large scale taxi GPS data

Science.gov (United States)

Tang, Jinjun; Liu, Fang; Wang, Yinhai; Wang, Hua

2015-11-01

Taxi GPS trajectories data contain massive spatial and temporal information of urban human activity and mobility. Taking taxi as mobile sensors, the information derived from taxi trips benefits the city and transportation planning. The original data used in study are collected from more than 1100 taxi drivers in Harbin city. We firstly divide the city area into 400 different transportation districts and analyze the origin and destination distribution in urban area on weekday and weekend. The Density-Based Spatial Clustering of Applications with Noise (DBSCAN) algorithm is used to cluster pick-up and drop-off locations. Furthermore, four spatial interaction models are calibrated and compared based on trajectories in shopping center of Harbin city to study the pick-up location searching behavior. By extracting taxi trips from GPS data, travel distance, time and average speed in occupied and non-occupied status are then used to investigate human mobility. Finally, we use observed OD matrix of center area in Harbin city to model the traffic distribution patterns based on entropy-maximizing method, and the estimation performance verify its effectiveness in case study.

Last Call: decreasing drunk driving among 21-34-year-old bar patrons.

Science.gov (United States)

Rivara, Frederick P; Boisvert, Deanne; Relyea-Chew, Annemarie; Gomez, Tony

2012-01-01

Any effort to decrease the toll of drunk driving must include efforts directed at people who drink in bars, particularly young adults who use motor vehicles after drinking. We designed a multifaceted social marketing campaign, Last Call, to increase the use of designated drivers and safe rides homes among 21-34-year olds. There were three components to the intervention: (1) use of taxi stands to promote taxi use; (2) point-of-sale information to patrons at partner bars and (3) a mass media campaign to support the designated driver/safe ride home message. Among the heaviest drinkers, the programme significantly increased the use of designated drivers and increased the use of taxis by 63%.

Evaluating the accuracy of GPS-based taxi trajectory records

NARCIS (Netherlands)

Zheng, Zhong; Rasouli, Soora; Timmermans, Harry

2014-01-01

Taxi data are an underused source of travel information. A handful of research has been concerned with the processing of raw taxi GPS data to minimize random error. The study of methods that systematically detect erroneous data has, however, received less attention. Generally, an origin and a

REQUIREMENTS FOR DESIGN, EQUIPMENT AND OPERATION MODE OF TAXI VEHICLES

Directory of Open Access Journals (Sweden)

Norayr Oganesovich Bludyan

2015-09-01

Full Text Available The analysis of international experience in application of requirements for the taxi vehicles design and equipment. The approaches to improvement of cabbing have been defined by determination of requirements for taxi vehicles.

Sudden illness while driving a vehicle--a retrospective analysis of commercial drivers in Japan.

Science.gov (United States)

Hitosugi, Masahito; Gomei, Sayaka; Okubo, Takao; Tokudome, Shogo

2012-01-01

We performed a retrospective analysis of commercial drivers to clarify the background of incidents of sudden illness while driving. The analysis used reports submitted by employers to the Japan Ministry of Land, Infrastructure, Transport, and Tourism regarding commercial drivers who had been ordered to stop driving owing to health problems. Of 211 cases with an average work history of 15.2 years, there were 88 bus drivers, 70 taxi drivers, and 53 truck drivers, 36.0% of who had died as a result of their disease. Among taxi and truck drivers, more than 70% of incidents were due to cardiac, aortic, and cerebrovascular disease. More than 80% of these were unable to avoid traffic accidents caused by sudden illness. However, among bus drivers, cardiac, aortic, and cerebrovascular disease accounted for only 23.5% of incidents, and accidents were avoided in more than half of the cases. The duration between starting work and the incident time was significantly shorter among bus drivers [mean 3.3 hours, standard deviation (SD) 3.1] than taxi (7.7 hours, SD 5.8) and truck (7.2 hours, SD 6.3) drivers (Pprevent disabling events while driving. As a precaution, physicians should advise commercial drivers to stop driving as soon as they detect slight discomfort. To prevent accidents, more assertive health promotion aimed at professional drivers is needed.

Optimization of the revenue of the New York city taxi service using Markov Decision Processes

NARCIS (Netherlands)

Li, P.; Bhulai, Sandjai; van Essen, J.T.; Bhulai, Sandjai; Kardaras, Dimitris

2017-01-01

Taxis are an essential component of the transportation system in most urban centers. The ability to optimize the efficiency of routing represents an opportunity to increase revenues for taxi drivers. The vacant taxis cruising on the roads are not only wasting fuel consumption, the time of a taxi

Health assessment of taxi drivers in the city of Tshwane

Directory of Open Access Journals (Sweden)

Tendani S. Ramukumba

2016-11-01

Conclusion: The findings implicate that the health status of taxi operators in Tshwane was a serious concern and urgent concerted effort is needed to engage in lifestyle modification of taxi drivers. The need for health promotion and formalised occupational health services was recommended.

Hematocrit levels as cardiovascular risk among taxi drivers in Bangkok, Thailand

OpenAIRE

ISHIMARU, Tomohiro; ARPHORN, Sara; JIRAPONGSUWAN, Ann

2016-01-01

In Thailand, taxi drivers employed in the informal sector often experience hazardous working conditions. Previous studies revealed that elevated Hematocrit (HCT) is a predictor of cardiovascular disease (CVD) risk. This study assessed factors associated with HCT in taxi drivers to predict their occupational CVD risk factors. A cross-sectional study was conducted on 298 male taxi drivers who joined a health check-up campaign in Bangkok, Thailand. HCT and body mass index were retrieved from par...

Dansk Taxi Råd har brug for et sprogkursus

DEFF Research Database (Denmark)

Riis, Helle Bach

2011-01-01

16.10. afviser formanden for Dansk Taxi Råd, John Lindbom, at det nyindførte pointsystem har til hensigt at holde indvandrere fra at blive vognmænd. I stedet siger han, at det handler om at højne fagets status og serviceniveau. Dansk Taxi Råd kan komme langt ved at forbedre sin interkulturelle...

Hubungan Upah dan Penawaran Tenaga Kerja Supir Taxi di Surabaya

Directory of Open Access Journals (Sweden)

Achmad Solihin

2014-05-01

Full Text Available Utilizing 50 (fifty of taxi drivers, who has been observing around 100 (one hundred working days, this study exploring whether the prediction of Neoclassical theory or the Reference Dependence Point (RDP about income targetting are followed by the taxi drivers in Surabaya city. Neoclassical theory assume that workers will respond positively with the transitory wage change, while the Reference Dependence Point, especially income targetting predict there is negative relationship between labor supply and positive wage income transitory. RDP theory predict that workers will decide reducing their working hours or stopping to work when their wage income has exceed their targetted income. Most of the previous studies evaluate the RDP hiphotesis on taxi drivers. In this study we find that among 50 (fifty taxi drivers being observed in Surabaya following the prediction of RDP theory. The point elasticity of labor supply in respond to positive wage changing has been found on the range of -0.004 % to -0.0012%.

Prevalence of Psychoactive Drug Use by Taxi Drivers in Nigeria ...

African Journals Online (AJOL)

Aim: To ascertain the prevalence and nature of psychoactive drug use amongst taxi drivers in Nigeria. Materials and Method: A total of 192 taxi drivers in Enugu, South East Nigeria was studied using a questionnaire. Information obtained from the questionnaire included socio-demographic characteristics of the drivers, ...

Utilising excess minibus-taxi capacity for South African townships tours

NARCIS (Netherlands)

Rietjens, S.J.H.; Makoriwa, Collins; de Boer, S.J.

2006-01-01

This paper proposes an option for the utilisation of excess off-peak capacity of minibus-taxis in South Africa for township tours. The minibus-taxi system typically faces steep peak loads during rush hours with excess vehicle and person capacity available during off-hours. The advantages of the

Taxi-Out Time Prediction for Departures at Charlotte Airport Using Machine Learning Techniques

Science.gov (United States)

Lee, Hanbong; Malik, Waqar; Jung, Yoon C.

2016-01-01

Predicting the taxi-out times of departures accurately is important for improving airport efficiency and takeoff time predictability. In this paper, we attempt to apply machine learning techniques to actual traffic data at Charlotte Douglas International Airport for taxi-out time prediction. To find the key factors affecting aircraft taxi times, surface surveillance data is first analyzed. From this data analysis, several variables, including terminal concourse, spot, runway, departure fix and weight class, are selected for taxi time prediction. Then, various machine learning methods such as linear regression, support vector machines, k-nearest neighbors, random forest, and neural networks model are applied to actual flight data. Different traffic flow and weather conditions at Charlotte airport are also taken into account for more accurate prediction. The taxi-out time prediction results show that linear regression and random forest techniques can provide the most accurate prediction in terms of root-mean-square errors. We also discuss the operational complexity and uncertainties that make it difficult to predict the taxi times accurately.

Exploring Intracity Taxi Mobility during the Holidays for Location-Based Marketing

Directory of Open Access Journals (Sweden)

Wen-jun Wang

2017-01-01

Full Text Available Taxi mobility information can be considered as an important source of mobile location-based information for making marketing decisions. So, studying the behavioral patterns of taxis in a Chinese city during the holidays using the global positioning system (GPS can yield remarkable insights into people’s holiday travel patterns, as well as the odd-even day vehicle prohibition system. This paper studies the behavioral patterns of taxis during specific holidays in terms of pick-up and drop-off locations, travel distance, mobile step length, travel direction, and radius of gyration on the basis of GPS data. Our results support the idea of a polycentric city. It is concluded from the reporting results that there are no significant changes in the distribution of pick-up and drop-off locations, travel distance, or travel direction during holidays in comparison to work days. The results suggest that human travel by taxi has a stable regularity. However, the radius of gyration of movement by most of the taxis becomes significantly larger during holidays that indicate more long-distance travels. The current study will be helpful for location-based marketing during the holidays.

DISPAQ: Distributed Profitable-Area Query from Big Taxi Trip Data.

Science.gov (United States)

Putri, Fadhilah Kurnia; Song, Giltae; Kwon, Joonho; Rao, Praveen

2017-09-25

One of the crucial problems for taxi drivers is to efficiently locate passengers in order to increase profits. The rapid advancement and ubiquitous penetration of Internet of Things (IoT) technology into transportation industries enables us to provide taxi drivers with locations that have more potential passengers (more profitable areas) by analyzing and querying taxi trip data. In this paper, we propose a query processing system, called Distributed Profitable-Area Query ( DISPAQ ) which efficiently identifies profitable areas by exploiting the Apache Software Foundation's Spark framework and a MongoDB database. DISPAQ first maintains a profitable-area query index (PQ-index) by extracting area summaries and route summaries from raw taxi trip data. It then identifies candidate profitable areas by searching the PQ-index during query processing. Then, it exploits a Z-Skyline algorithm, which is an extension of skyline processing with a Z-order space filling curve, to quickly refine the candidate profitable areas. To improve the performance of distributed query processing, we also propose local Z-Skyline optimization, which reduces the number of dominant tests by distributing killer profitable areas to each cluster node. Through extensive evaluation with real datasets, we demonstrate that our DISPAQ system provides a scalable and efficient solution for processing profitable-area queries from huge amounts of big taxi trip data.

Analysis of the characteristics of taxi services as a prerequisite for their improvement

Directory of Open Access Journals (Sweden)

Vujić Nenad

2014-01-01

Full Text Available The expansion of services sector is the characteristics of modern and developed societies that influence national economy. Therefore, the analysis of services, as a concept and part of marketing is very significant. In this sense, the paper researches a particular service - the taxi services in the capital of Serbia. Through this research, the authors try to define the groups of customer of taxi services and their preference and attitudes. The research was performed in period May to July 2014, by direct contact with customer of taxi services. The results of research have confirmed the initial hypothesis and provide possibilities for further insight into the way of using taxi services and general circumstances that characterize them in mentioned region. On this basis, it is provided proposals for improvement of taxi services and easier outreach of target groups.

Hybrid Taxis Give Fuel Economy a Lift -Clean Cities Fleet Experiences -

Energy Technology Data Exchange (ETDEWEB)

None

2009-04-01

The hybrid taxis are able to achieve about twice the gas mileage of a conventional taxi while helping cut gasoline use and fuel costs. Tax credits and other incentives are helping both company owners and drivers make the switch to hybrids.

Examining the Interaction of Taxi and Subway Ridership for Sustainable Urbanization

Directory of Open Access Journals (Sweden)

Miaoyi Li

2017-02-01

Full Text Available A transit ridership study is an essential part of sustainability, and can provide a deep understanding of people’s travel patterns for efficient transportation development and urbanization. However, there is a lack of empirical studies comparing subway and taxi services, and their interactions within a city, that is to say, the interdependent transportation networks. Incorporating new data, this study aims to examine the spatial variation of urban taxi ridership due to the impacts of a new subway line operation opened in 2014 in Wuxi, China. We examine the spatial patterns and interactions of ridership in Wuxi by integrating taxi trajectory from GPS data and subway data from continuously collected fare transactions. The results indicated that the demand for taxi and subway usage is quite elastic with respect to both location and time, and the new subway’s opening had more influence on areas adjacent to subway stations and urban center-suburban travel. Furthermore, increases in travel time and distance would increase the demand for subway, while taxi trips largely represented movements for those locations that the subway could not reach. This paper betters the understanding of travel patterns through large volumes of transportation data for sustainable urbanization policy design.

Considering the effects of ambient particulate matter on the lung function of motorcycle taxi drivers in Bangkok, Thailand.

Science.gov (United States)

Arphorn, Sara; Ishimaru, Tomohiro; Hara, Kunio; Mahasandana, Suwisa

2018-02-01

The motorcycle taxi drivers of Bangkok have been heavily exposed to high concentrations of PM 10 (particulate matter with an aerodynamic diameter ≤10 μm), and the impact of this on their lungs has been neither documented nor studied. This study examines the association between exposure to PM 10 and lung function decline among motorcycle taxi drivers. A cross-sectional study was conducted in Bangkok between two groups: a subject group of motorcycle taxi drivers and control group of enclosed vehicle taxi drivers. The findings of the Thailand Pollution Control Department were used to estimate the annual ambient PM 10 concentration levels in the metropolis. Pulmonary functions of motorcycle taxi drivers and enclosed vehicle taxi drivers were measured and compared using the Mann-Whitney test. Multiple linear regression analysis was applied to estimate the effects of PM 10 exposure on the lung function of motorcycle taxi drivers. A total of 1283 motorcycle taxi drivers and 600 taxi drivers were investigated. The mean forced expiratory volume in 1 sec/forced vital capacity (FEV 1 /FVC) of the motorcycle taxi drivers was significantly lower than that of the taxi drivers (P Organization (WHO) vehicular emission standards should be recognized and eventually enforced.

Research on Taxi Driver Strategy Game Evolution with Carpooling Detour

Directory of Open Access Journals (Sweden)

Wei Zhang

2018-01-01

Full Text Available For the problem of taxi carpooling detour, this paper studies driver strategy choice with carpooling detour. The model of taxi driver strategy evolution with carpooling detour is built based on prospect theory and evolution game theory. Driver stable strategies are analyzed under the conditions of complaint mechanism and absence of mechanism, respectively. The results show that passenger’s complaint mechanism can effectively decrease the phenomenon of driver refusing passengers with carpooling detour. When probability of passenger complaint reaches a certain level, the stable strategy of driver is to take carpooling detour passengers. Meanwhile, limiting detour distance and easing traffic congestion can decrease the possibility of refusing passengers. These conclusions have a certain guiding significance to formulating taxi policy.

Spatiotemporal Patterns of Carbon Emissions and Taxi Travel Using GPS Data in Beijing

Directory of Open Access Journals (Sweden)

Jinlei Zhang

2018-02-01

Full Text Available Taxis are significant contributors to carbon dioxide emissions due to their frequent usage, yet current research into taxi carbon emissions is insufficient. Emerging data sources and big data–mining techniques enable analysis of carbon emissions, which contributes to their reduction and the promotion of low-carbon societies. This study uses taxi GPS data to reconstruct taxi trajectories in Beijing. We then use the carbon emission calculation model based on a taxi fuel consumption algorithm and the carbon dioxide emission factor to calculate emissions and apply a visualization method called kernel density analysis to obtain the dynamic spatiotemporal distribution of carbon emissions. Total carbon emissions show substantial temporal variations during the day, with maximum values from 10:00–11:00 (57.53 t, which is seven times the minimum value of 7.43 t (from 03:00–04:00. Carbon emissions per kilometer at the network level are steady throughout the day (0.2 kg/km. The Airport Expressway, Ring Roads, and large intersections within the 5th Ring Road maintain higher carbon emissions than other areas. Spatiotemporal carbon emissions and travel patterns differ between weekdays and weekends, especially during morning rush hours. This research provides critical insights for taxi companies, authorities, and future studies.

Hybrid Taxis Give Fuel Economy a Lift, Clean Cities, Fleet Experiences, April 2009 (Fact Sheet)

Energy Technology Data Exchange (ETDEWEB)

2009-04-01

Clean Cities helped Boston, San Antonio, and Cambridge create hybrid taxi programs. The hybrid taxis are able to achieve about twice the gas mileage of a conventional taxi while helping cut gasoline use and fuel costs. Tax credits and other incentives are helping both company owners and drivers make the switch to hybrids. Program leaders have learned some important lessons other cities can benefit from including learning a city's taxi structure, relaying benefits to drivers, and understanding the needs of owners.

Cost Reduction of Taxi Enterprises at the Expense of Automobile Fleet Optimization

Directory of Open Access Journals (Sweden)

Novytskyi А.V.

2016-05-01

Full Text Available Results of taxi service operation using techniques of queuing system theory have been demonstrated. It has been shown that probability of service denial is the key quality criterion of transport services for taxi services. It is expedient to use total expenditures of queuing system as target function to estimate the efficiency of taxi service. It has been determined that application of queuing theory techniques makes it possible to identify optimum value of the number of operating motor vehicles for specific environment. The value is optimum according to minimum-cost criterion.

DISPAQ: Distributed Profitable-Area Query from Big Taxi Trip Data †

Science.gov (United States)

Putri, Fadhilah Kurnia; Song, Giltae; Rao, Praveen

2017-01-01

One of the crucial problems for taxi drivers is to efficiently locate passengers in order to increase profits. The rapid advancement and ubiquitous penetration of Internet of Things (IoT) technology into transportation industries enables us to provide taxi drivers with locations that have more potential passengers (more profitable areas) by analyzing and querying taxi trip data. In this paper, we propose a query processing system, called Distributed Profitable-Area Query (DISPAQ) which efficiently identifies profitable areas by exploiting the Apache Software Foundation’s Spark framework and a MongoDB database. DISPAQ first maintains a profitable-area query index (PQ-index) by extracting area summaries and route summaries from raw taxi trip data. It then identifies candidate profitable areas by searching the PQ-index during query processing. Then, it exploits a Z-Skyline algorithm, which is an extension of skyline processing with a Z-order space filling curve, to quickly refine the candidate profitable areas. To improve the performance of distributed query processing, we also propose local Z-Skyline optimization, which reduces the number of dominant tests by distributing killer profitable areas to each cluster node. Through extensive evaluation with real datasets, we demonstrate that our DISPAQ system provides a scalable and efficient solution for processing profitable-area queries from huge amounts of big taxi trip data. PMID:28946679

Taxi Time Prediction at Charlotte Airport Using Fast-Time Simulation and Machine Learning Techniques

Science.gov (United States)

Lee, Hanbong

2016-01-01

Accurate taxi time prediction is required for enabling efficient runway scheduling that can increase runway throughput and reduce taxi times and fuel consumptions on the airport surface. Currently NASA and American Airlines are jointly developing a decision-support tool called Spot and Runway Departure Advisor (SARDA) that assists airport ramp controllers to make gate pushback decisions and improve the overall efficiency of airport surface traffic. In this presentation, we propose to use Linear Optimized Sequencing (LINOS), a discrete-event fast-time simulation tool, to predict taxi times and provide the estimates to the runway scheduler in real-time airport operations. To assess its prediction accuracy, we also introduce a data-driven analytical method using machine learning techniques. These two taxi time prediction methods are evaluated with actual taxi time data obtained from the SARDA human-in-the-loop (HITL) simulation for Charlotte Douglas International Airport (CLT) using various performance measurement metrics. Based on the taxi time prediction results, we also discuss how the prediction accuracy can be affected by the operational complexity at this airport and how we can improve the fast time simulation model before implementing it with an airport scheduling algorithm in a real-time environment.

Investigation of in-cabin volatile organic compounds (VOCs) in taxis; influence of vehicle's age, model, fuel, and refueling.

Science.gov (United States)

Bakhtiari, Reza; Hadei, Mostafa; Hopke, Philip K; Shahsavani, Abbas; Rastkari, Noushin; Kermani, Majid; Yarahmadi, Maryam; Ghaderpoori, Afshin

2018-06-01

The air pollutant species and concentrations in taxis' cabins can present significant health impacts on health. This study measured the concentrations of benzene, toluene, ethylbenzene, xylene (BTEX), formaldehyde, and acetaldehyde in the cabins of four different taxi models. The effects of taxi's age, fuel type, and refueling were investigated. Four taxi models in 3 age groups were fueled with 3 different fuels (gas, compressed natural gas (CNG), and liquefied petroleum gas (LPG)), and the concentrations of 6 air pollutants were measured in the taxi cabins before and after refueling. BTEX, formaldehyde, and acetaldehyde sampling were actively sampled using NIOSH methods 1501, 2541, and 2538, respectively. The average BTEX concentrations for all taxi models were below guideline values. The average concentrations (±SD) of formaldehyde in Model 1 to Model 4 taxis were 889 (±356), 806 (±323), 1144 (±240), and 934 (±167) ppbv, respectively. Acetaldehyde average concentrations (±SD) in Model 1 to Model 4 taxis were 410 (±223), 441 (±241), 443 (±210), and 482 (±91) ppbv, respectively. Refueling increased the in-vehicle concentrations of pollutants primarily the CNG and LPG fuels. BTEX concentrations in all taxi models were significantly higher for gasoline. Taxi age inversely affected formaldehyde and acetaldehyde. In conclusion, it seems that refueling process and substitution of gasoline with CNG and LPG can be considered as solutions to improve in-vehicle air concentrations for taxis. Copyright © 2018. Published by Elsevier Ltd.

Respiratory symptoms and lung function in garage workers and taxi drivers.

Science.gov (United States)

Bener, A; Galadari, I; al-Mutawa, J K; al-Maskari, F; Das, M; Abuzeid, M S

1998-12-01

The aim of this study was to determine the prevalence of some respiratory symptoms and possible diseases among occupationally-exposed garage workers and taxi drivers. This study involved 158 garage workers and 165 taxi drivers, matched for age, sex, nationality and duration of employment. The mean age of 158 Indian subcontinent garage workers was 34.4 +/- 10.4 years; their mean height and weight were 167.7 +/- 6.6 cm and 72.0 +/- 12.3 kg respectively, and the mean duration of employment garage workers was 8.8 +/- 7.6 years. The mean age of 165 Indian subcontinent male taxi drivers was 34.5 +/- 7.7 years; their mean height and weight were 168.7 +/- 6.1 cm and 71.3 +/- 12.6 kg respectively; and the mean duration of employment was 7.5 +/- 5.4 years. The data on chronic respiratory symptoms showed that garage workers had higher prevalence of symptoms than taxi drivers being significantly greater for chronic phlegm, (p UAE), may be associated with the development of chronic respiratory symptoms and have effects on their daily life and health.

Calidad del servicio de taxis del municipio Maracaibo

Directory of Open Access Journals (Sweden)

Joheni A. Urdaneta G.

2011-05-01

Full Text Available El presente trabajo tiene como objetivo describir la calidad del servicio de los taxis en el municipio Maracaibo, ya que los mismos forman parte del sistema de transporte urbano de la ciudad, y es un servicio público fundamental para la convivencia de la sociedad; para lograr este objetivo se realizó una adaptación del modelo SERVPERF, diseñando un instrumento tipo cuestionario, con 32 ítems en 6 dimensiones, adecuado a las características propias del servicio de taxi, con la finalidad de confirmar que los ítems de los instrumentos se correspondían con las dimensiones adaptadas se aplicó la técnica de análisis factorial resultando un nuevo instrumento con 24 ítems en 3 dimensiones. Se utilizó la escala de Likert con tres (3 alternativas de respuesta. La investigación es de tipo descriptiva y aplicada, bajo diseño no experimental de tipo transeccional descriptiva y de campo. La población quedó conformada por los usuarios de las líneas de taxis del municipio Maracaibo. Se aplicó muestreo aleatorio por conglomerado. La confiabilidad del instrumento se midió a través del coeficiente alfa de Cronbach resultando de 0,82 lo cual se considera aceptable. Los resultados revelan que la calidad del servicio de taxis del municipio Maracaibo es mediana por lo tanto este servicio es susceptible a mejoras, las cuales son necesarias para elevar la calidad de vida de los marabinos. Este resultado se obtuvo con el instrumento originalmente adaptado de 32 ítems y con el cuestionario resultante del análisis factorial, de 24 ítems; esto confirma lo apropiado de esta técnica, ya que se redujo el número de ítems y de las dimensiones originalmente adaptadas y no se encontraron diferencias significativas en los resultados con ambos instrumentos; de esta manera se puede medir la calidad del servicio de taxis en el municipio Maracaibo a través de las dimensiones: confiabilidad del servicio, socialización y responsabilidad.

[Occupational risk factors and perceptions of air pollution by motorcycle taxi drivers in Cotonou, Benin].

Science.gov (United States)

Lawin, Hervé; Ayi Fanou, Lucie; Hinson, Vikkey; Tollo, Brice; Fayomi, Benjamin; Ouendo, Edgard-Marius

Motorcycle taxis occupy a major place in urban transport. Motorcycle taxi drivers are exposed to occupational risk factors (ORF) including air pollution. The objective of this study was to evaluate these ORF among motorcycle taxi drivers and their perceptions of air pollution. This mixed study was conducted on motorcycle taxi drivers in Cotonou. The qualitative study was based on focus groups concerning 16 items from the Participatory Occupational Risk Screening Guide (DEPARIS) until saturation and after triangulation of data. The quantitative study consisted of administering a questionnaire addressing socioeconomic and demographic characteristics, cardiopulmonary diseases, and perception of air -pollution risk factors among 397 Cotonou motorcycle taxi drivers. Drivers perceived poor road conditions, effort and handling, and lack of social security as unsatisfactory ORF. Their mean age was 40.95 ± 8.75 years and 45.84% had primary -education. They had been working as motorcycle taxi drivers for an average of 134.95 ± 101.53 months with an average income of FCFA 3138 ± 1238. These occupational factors were significantly associated with cardiopulmonary disorders, observed in 63.2% of drivers. Less than 1/3 of drivers felt that air pollution affected their personal health. Motorcycle taxi drivers have a poor perception of ORF and the severity of exposure to air pollution in this occupation. There is a need to take action to promote the health of this population.

Energy Optimal Control of Induction Motor Drives

DEFF Research Database (Denmark)

Abrahamsen, Flemming

This thesis deals with energy optimal control of small and medium-size variable speed induction motor drives for especially Heating, Ventilation and Air-Condition (HVAC) applications. Optimized efficiency is achieved by adapting the magnetization level in the motor to the load, and the basic...... demonstrated that energy optimal control will sometimes improve and sometimes deteriorate the stability. Comparison of small and medium-size induction motor drives with permanent magnet motor drives indicated why, and in which applications, PM motors are especially good. Calculations of economical aspects...... improvement by energy optimal control for any standard induction motor drive between 2.2 kW and 90 kW. A simple method to evaluate the robustness against load disturbances was developed and used to compare the robustness of different motor types and sizes. Calculation of the oscillatory behavior of a motor...

Risky driving behaviors for road traffic accident among drivers in Mekele city, Northern Ethiopia

Directory of Open Access Journals (Sweden)

Hassen Abrahim

2011-12-01

Full Text Available Abstract Background Due to its perception as a disease of development, road traffic accident and related injuries tend to be under recognized as a major health problem in developing countries. However, majority of the world's fatalities on the roads occur in low income and middle income countries. Since the main cause of road traffic accident is attributed to human risky behaviors, it is important to identify significant factors for risky behaviors of drivers. Methods A quantitative cross-sectional study with a sample size of 350 drivers was conducted in April 2011. The study was conducted among Taxi, Bajaj (three tire vehicles and private owned car drivers. After proportion to size allocation for Taxi (75, Baja (103 and private owned car (172 drivers, we used systematic random sampling method to identify illegible study subjects. Data was collected with face to face interview using a pretested questioner. Univariate, bivariate and multivariate analysis was done using SPSS version 16. Results The mean age of the respondents was 28.7 (SD 9.9. Majority were 339 (96.9% males. Significant number of the study subjects 233 (66.6% had risky driving behaviors. More than a quarter 100 (28.6% had less knowledge about basic traffic signs. Majority of drivers 181 (51.7% had negative attitude towards risky driving behaviors. Significant percent of them 148 (42.3% had a habit of using mobile phone while driving vehicle and 28 (9.7% had experience of driving after drinking alcohol. All the Bajaj, 97(62.6% house car and 58(37.4% taxi unfasten their seat belt while driving. Majority 303 (86.6% followed the recommended speed limit of driving. About 66 (18.9% of them had experience of punishment or warning by traffic polices in the previous 1 year and 77 (22% ever had car accident while driving. Conclusions Drivers of secondary education and with high average monthly income were more likely to have risky driving behavior. Having supportive attitude towards risky

Switching from motorcycle taxi to walking: A case study of transit station access in Bangkok, Thailand

Directory of Open Access Journals (Sweden)

Pornraht Pongprasert

2017-12-01

Full Text Available This study aims to find the factors affecting residents near transit stations within 1000 m, who are referred to as transit-oriented development (TOD residents, to reduce motorcycle taxi use and encourage walking to stations. These two modes of commuting are the most popular among over 85% of residents. However, motorcycle taxis are the main pedestrian barriers that hinder easy access and walkability in TODs of Bangkok, because they ride, stop, and provide services on sidewalks. From 2013 to 2015, these problems substantially increased the number of motorcycle taxis that are not willing and able to follow the rules. The increasing number of pedestrian accidents on sidewalks is related to the increase in the number of motorcycle taxis. According to a survey on pedestrian safety with 249 respondents, over 25% of walkers feel unsafe to walk, while 40% of motorcycle-taxi users riding to stations do not walk because they are afraid of accidents. In modal split, the share of walking reduces from 76% for areas < 500 m, to 25% for areas between 500 and 1000 m from transit stations, respectively. Hence, the number of motorcycle taxis in the 500–1000 m range is twice as high compared to that within the 500 m area. If motorcycle taxi users would accept a longer walking distance to station by 36 m or would be willing to walk to the station within 9.15 min, 54% of them may switch to walking to stations. Moreover, based on the estimation results of the logistic regression models, middle-adult aged residents, office employees, residents owning a car, and people living far from stations are less likely to walk. Average income households and commuters during non-peak hours tend to use motorcycle taxis more. On the other hand, residents living far from stations tend to use motorcycle taxis less, because most of the motorcycle taxi services are located near transit stations. Keywords: Transit accessibility, Pedestrian, Walkability

Filters from taxis air conditioning system: A tool to characterize driver's occupational exposure to bioburden?

Science.gov (United States)

Viegas, Carla; Monteiro, Ana; Dos Santos, Mateus; Faria, Tiago; Caetano, Liliana Aranha; Carolino, Elisabete; Quintal Gomes, Anita; Marchand, Geneviève; Lacombe, Nancy; Viegas, Susana

2018-07-01

Bioburden proliferation in filters from air conditioning systems of taxis represents a possible source of occupational exposure. The aim of this study was to determine the occurrence of fungi and bacteria in filters from the air conditioning system of taxis used for patient transportation and to assess the exposure of drivers to bioburden. Filters from the air conditioning systems of 19 taxis and 28 personal vehicles (used as controls) operating in three Portuguese cities including the capital Lisbon, were collected during the winter season. The occurrence and significance of bioburden detected in the different vehicles are reported and discussed in terms of colony-forming units (CFU) per 1 m 2 of filter area and by the identification of the most frequently detected fungal isolates based on morphology. Azole-resistant mycobiota, fungal biomass, and molecular detection of Aspergillus species/strains were also determined. Bacterial growth was more prevalent in taxis (63.2%) than in personal vehicles (26.3%), whereas fungal growth was more prevalent in personal vehicles (53.6%) than in taxis (21.1-31.6%). Seven different azole-resistant species were identified in this study in 42.1% taxi filters. Levels of fungal biomass were above the detection limit in 63% taxi filters and in 75% personal vehicle filters. No toxigenic species were detected by molecular analysis in the assessed filters. The results obtained show that bioburden proliferation occurs widely in filters from the air conditioning systems of taxis, including the proliferation of azole-resistant fungal species, suggesting that filters should be replaced more frequently. The use of culture based-methods and molecular tools combined enabled an improved risk characterization in this setting. Copyright © 2018 Elsevier Inc. All rights reserved.

Developing a Decision-Support-Tool for an Air Taxi Service in Western Europe

NARCIS (Netherlands)

Van Wee, G.P.; Van Nes, R.; Van Duin, J.H.R.; Sengers, P.; Ghijs, S.S.A.

2008-01-01

This paper is a research proposal to develop a tool to analyze logistic concepts of the air taxi service of Aeolus Aviation in different scenarios. Based on this analysis recommendations can be done for a suitable logistic concept for Aeolus. Based on background analysis of the air taxi service

Three-wheeled scooter taxi: A safety analysis

Indian Academy of Sciences (India)

Three-wheel scooter taxis (TSR) form an essential part of public transport for the urban ... These low cost vehicles will remain a major mode of travel in the South Asian region ... commercial codes can be avoided for computational efficiency.

REVIEW OF ENERGY-SAVING TECHNOLOGIES IN MODERN HYDRAULIC DRIVES

Directory of Open Access Journals (Sweden)

Mykola Karpenko

2017-12-01

Full Text Available This paper focuses on review of modern energy­saving technologies in hydraulic drives. Described main areas of energy conservation in hydraulic drive (which in turn are divided into many under the directions and was established the popularity of them. Reviewed the comparative analysis of efficiency application of various strategies for energy saving in a hydraulic drive. Based on the review for further research a combined method of real­time control systems with energy­saving algorithms and regeneration unit – selected for maxing efficiency in hydraulic drive. Scientific papers (40 papers, what introduced in review, is not older than 15 years in the databases “Sciencedirect” and “Scopus”.

76 FR 33639 - Safety Zone; New York Water Taxi 10th Anniversary Fireworks

Science.gov (United States)

2011-06-09

...-AA00 Safety Zone; New York Water Taxi 10th Anniversary Fireworks, Upper New York Bay, Red Hook, NY... New York Water Taxi. The fireworks will commence at 9 p.m. on June 21, 2011 and will last... CFR Part 165 Harbors, Marine safety, Navigation (water), Reporting and recordkeeping requirements...

Detecting Traffic Anomalies in Urban Areas Using Taxi GPS Data

Directory of Open Access Journals (Sweden)

Weiming Kuang

2015-01-01

Full Text Available Large-scale GPS data contain hidden information and provide us with the opportunity to discover knowledge that may be useful for transportation systems using advanced data mining techniques. In major metropolitan cities, many taxicabs are equipped with GPS devices. Because taxies operate continuously for nearly 24 hours per day, they can be used as reliable sensors for the perceived traffic state. In this paper, the entire city was divided into subregions by roads, and taxi GPS data were transformed into traffic flow data to build a traffic flow matrix. In addition, a highly efficient anomaly detection method was proposed based on wavelet transform and PCA (principal component analysis for detecting anomalous traffic events in urban regions. The traffic anomaly is considered to occur in a subregion when the values of the corresponding indicators deviate significantly from the expected values. This method was evaluated using a GPS dataset that was generated by more than 15,000 taxies over a period of half a year in Harbin, China. The results show that this detection method is effective and efficient.

Taxi ! méthode de français : niveau 3

CERN Document Server

Johnson, Anne-Marie

2004-01-01

Taxi ! 3 est une méthode interactive, qui développe non seulement les connaissances, mais aussi les savoir-faire et les savoir-être de l'apprenant, à l'écrit comme à l'oral. La méthode est très simple à utiliser : une leçon = une double page. Taxi ! 3 couvre le niveau Bl du Cadre européen commun de référence pour l'apprentissage, l'enseignement et l'évaluation des langues. La méthode permet de se préparer aux épreuves A3 et A4 du DELF 1er degré. Une progression et des contenus fonctionnels et langagiers solides permettent à l'apprenant d'atteindre rapidement une autonomie en français dans des situations de la vie courante. Taxi ! 3 permet de mieux connaître la France d'aujourd'hui et les comportements des Français à travers une grande variété de documents authentiques (écrit et audio).

Characterizing urban structure using taxi GPS data

NARCIS (Netherlands)

Zheng, Zhong; Zhou, Suhong; Rasouli, S.; Timmermans, H.J.P.

2014-01-01

Scholars have explored urban structure from many perspectives. Developments in ICT have made it possible to discover spatial patterns in activities using big data. The identified patterns allow us to better understand urban structure. This chapter reports the collection of taxi GPS records for a

[Association between psychosocial aspects of work and quality of life among motorcycle taxi drivers].

Science.gov (United States)

Teixeira, Jules Ramon Brito; Boery, Eduardo Nagib; Casotti, Cezar Augusto; Araújo, Tânia Maria de; Pereira, Rafael; Ribeiro, Ícaro José Santos; Rios, Marcela Andrade; Amorim, Camila Rego; Moreira, Ramon Missias; Boery, Rita Narriman Silva de Oliveira; Sales, Zenilda Nogueira

2015-01-01

This study aimed to evaluate the quality of life of motorcycle taxi drivers and the association with psychosocial characteristics of their work. This was a cross-sectional epidemiological study with a sample of 400 motorcycle taxi drivers in Jequié, Bahia State, Brazil. The study used a form containing demographic and socioeconomic data, WHO Quality of Life-Bref Questionnaire (WHOQOL-Bref), and the Job Content Questionnaire (JCQ). Motorcycle taxi drivers with greater decision-making control over their work showed better self-rated quality of life in the psychological domain; those with high psychological demands presented better self-rated quality of life in the social relations and environmental domains; those with high strain and active work showed better self-rated quality of life in the social and environmental domains. The psychosocial work environment and especially decision-making autonomy were thus important determinants of self-rated quality of life in this group of motorcycle taxi drivers.

Institutional statism: an overview of the formulation of the taxi recapitalisation policy

Directory of Open Access Journals (Sweden)

D. van Schalkwyk

2008-07-01

Full Text Available This article provides an overview of the government’s formulation of the taxi recapitalisation policy which is aimed at regulating the minibus taxi industry. Coupled with a brief social and politico-historical context of the policy, the aim is to highlight the government’s statist conduct in the formulation of the recapitalisation policy. The minibus taxi industry started to fulfil a prominent role in the 1970s as a result of a loophole in the legislation of the former apartheid government. It is currently the most accessible mode of public transport and conveys 65 per cent of the country’s commuters daily. Consequently, the Industry is an imperative force to be considered by the government in its formulation of transport policies. However, the industry is characterised by numerous problems, including a high rate of minibus taxis involved in accidents, unroadworthy vehicles and violence. It is in this context that the government formulated both the original and revised versions of the recapitalisation policy. However, the formulation of the policy has been problematic. The government followed a statist approach during the formulation process when it directed the course of the process according to its interests and without adequate consultation with relevant role players.

Research on Strategy Control of Taxi Carpooling Detour Route under Uncertain Environment

Directory of Open Access Journals (Sweden)

Wei Zhang

2016-01-01

Full Text Available For the problem of route choice in taxi carpooling detour, considering the uncertainty of traffic and the characteristic of passengers’ noncomplete rationality, an evolutionary game model of taxi carpooling detour route is built, in which prospect theory is introduced and revenue of strategy is replaced by prospect value. The model reflects more really decision-making psychology of passengers. Then the stable strategies of the model are studied, and the influences of detour distance and traffic congestion on detour carpooling success are analyzed, respectively. The results show that when at least one route of which prospect values for two passenger sides are both positive exists, carpooling route can reach an agreement. The route is stable strategy of evolutionary game, and the passengers requiring short travel time tend to select the nondetour route. With the increase of detour distance and traffic congestion rate, the possibility of reaching an agreement decreases gradually; that is, possibility of carpooling failure increases. So taxi carpooling detour is possible under the certain condition, but some measures must be carried out such as constraints of detour distance and mitigation of traffic congestion to improve carpooling success probability. These conclusions have a certain guiding significance to the formulation of taxi carpooling policy.

Terminal area automatic navigation, guidance, and control 1: Automatic rollout, turnoff, and taxis

Science.gov (United States)

Pines, S.

1981-01-01

A study developed for the TCV B-737, designed to apply existing navigation aids plus magnetic leader cable signals and develop breaking and reverse thrust guidance laws to provide for rapid automated rollout, turnoff, and taxi to reduce runway occupation time for a wide variety of landing conditions for conventional commercial-type aircraft, is described. Closed loop guidance laws for braking and reverse thrust are derived for rollout, turnoff, and taxi, as functions of the landing speed, the desired taxi speed and the distance to go. Brake limitations for wet runway conditions and reverse thrust limitations are taken into account to provide decision rules to avoid tire skid and to choose an alternate turnoff point, farther down the runway, to accommodate extreme landing conditions.

Assessing the impacts of deploying a shared self-driving urban mobility system: An agent-based model applied to the city of Lisbon, Portugal

Directory of Open Access Journals (Sweden)

Luis M. Martinez

2017-06-01

Full Text Available This paper examines the changes that might result from the large-scale uptake of a shared and self-driving fleet of vehicles in a mid-sized European city. The work explores two different self-driving vehicle concepts – a ridesharing system (Shared Taxi, which emulates a taxi-like system where customers accept small detours from their original direct path and share part of their ride with others and a dynamic bus-like service with minibuses (Taxi-Bus, where customers pre-book their service at least 30 min in advance (permanent bookings for regular trips should represent most requests and walk short distances to a designated stop. Under the premise that the “upgraded” system should as much as possible deliver the same trips as today in terms of origin, destination and timing, and that it should also replace all car and bus trips, it looks at impacts on car fleet size, volume of travel and parking requirements. Mobility output and CO2 emissions are also detailed in two different time scales (24 h. average and peak-hour only. The obtained results suggest that a full implementation scenario where the existing metro service is kept and private car, bus and taxi mobility would be replaced by shared modes would significantly reduce travelled vehicle.kilometres and CO2 emissions.

Economic Analysis on Value Chain of Taxi Fleet with Battery-Swapping Mode Using Multiobjective Genetic Algorithm

OpenAIRE

Ning, Guobao; Zhen, Zijian; Wang, Peng; Li, Yang; Yin, Huaixian

2012-01-01

This paper presents an economic analysis model on value chain of taxi fleet with battery-swapping mode in a pilot city. In the model, economic benefits of charging-swapping station group, taxi company, and taxi driver in the region have been taken into consideration. Thus, the model is a multiobjective function and multiobjective genetic algorithm is used to solve this problem. According to the real data collected from the pilot city, the multiobjective genetic algorithm is tested as an effec...

Ternary-fragmentation-driving potential energies of 252Cf

Science.gov (United States)

Karthikraj, C.; Ren, Zhongzhou

2017-12-01

Within the framework of a simple macroscopic model, the ternary-fragmentation-driving potential energies of 252Cf are studied. In this work, all possible ternary-fragment combinations of 252Cf are generated by the use of atomic mass evaluation-2016 (AME2016) data and these combinations are minimized by using a two-dimensional minimization approach. This minimization process can be done in two ways: (i) with respect to proton numbers (Z1, Z2, Z3) and (ii) with respect to neutron numbers (N1, N2, N3) of the ternary fragments. In this paper, the driving potential energies for the ternary breakup of 252Cf are presented for both the spherical and deformed as well as the proton-minimized and neutron-minimized ternary fragments. From the proton-minimized spherical ternary fragments, we have obtained different possible ternary configurations with a minimum driving potential, in particular, the experimental expectation of Sn + Ni + Ca ternary fragmentation. However, the neutron-minimized ternary fragments exhibit a driving potential minimum in the true-ternary-fission (TTF) region as well. Further, the Q -value energy systematics of the neutron-minimized ternary fragments show larger values for the TTF fragments. From this, we have concluded that the TTF region fragments with the least driving potential and high Q values have a strong possibility in the ternary fragmentation of 252Cf. Further, the role of ground-state deformations (β2, β3, β4, and β6) in the ternary breakup of 252Cf is also studied. The deformed ternary fragmentation, which involves Z3=12 -19 fragments, possesses the driving potential minimum due to the larger oblate deformations. We also found that the ground-state deformations, particularly β2, strongly influence the driving potential energies and play a major role in determining the most probable fragment combinations in the ternary breakup of 252Cf.

Inconvenient and Unnecessary? Regulations in the U.S. Taxi Industry

Directory of Open Access Journals (Sweden)

Johnson Colton

2017-12-01

Full Text Available A Certificate of Public Convenience and Necessity (CPCN is a common requirement for a new business owner in services such as utilities, communications, healthcare, and transportation. However, studies have called into question the effectiveness and purpose of these laws when applied in certain industries. This study chronicles the development of and justifications provided for the enactment of CPCN laws. It then empirically tests the effectiveness of these laws in the taxi industry. This paper finds no evidence that the CPCN laws in the taxi industry are meeting their objectives. Some evidence suggests that CPCN laws achieve the opposite of their intention.

Constitutive expression of the xylanase inhibitor TAXI-III delays Fusarium head blight symptoms in durum wheat transgenic plants.

Science.gov (United States)

Moscetti, Ilaria; Tundo, Silvio; Janni, Michela; Sella, Luca; Gazzetti, Katia; Tauzin, Alexandra; Giardina, Thierry; Masci, Stefania; Favaron, Francesco; D'Ovidio, Renato

2013-12-01

Cereals contain xylanase inhibitor (XI) proteins which inhibit microbial xylanases and are considered part of the defense mechanisms to counteract microbial pathogens. Nevertheless, in planta evidence for this role has not been reported yet. Therefore, we produced a number of transgenic plants constitutively overexpressing TAXI-III, a member of the TAXI type XI that is induced by pathogen infection. Results showed that TAXI-III endows the transgenic wheat with new inhibition capacities. We also showed that TAXI-III is correctly secreted into the apoplast and possesses the expected inhibition parameters against microbial xylanases. The new inhibition properties of the transgenic plants correlate with a significant delay of Fusarium head blight disease symptoms caused by Fusarium graminearum but do not significantly influence leaf spot symptoms caused by Bipolaris sorokiniana. We showed that this contrasting result can be due to the different capacity of TAXI-III to inhibit the xylanase activity of these two fungal pathogens. These results provide, for the first time, clear evidence in planta that XI are involved in plant defense against fungal pathogens and show the potential to manipulate TAXI-III accumulation to improve wheat resistance against F. graminearum.

Association of Some Environmental Factors with Breath Carbon Monoxide Levels of Some Taxi Drivers in Ankara

Directory of Open Access Journals (Sweden)

Oguz Baran

2010-12-01

Full Text Available AIM: Taxi drivers are among the occupational groups with the highest smoking prevalence and exposure to carbon monoxide (CO. This study aimed to measure breath CO levels of some taxi drivers working in Ankara and to find out some associated factors (if any. METHOD: The descriptive study was carried out with 173 taxi drivers from 14 different taxi stations in the center of Ankara. Data was collected by face to face interviews with a standart questionnaire, while breath CO was measured by a Pi-CO Smokerlyser. Descriptive statistics were used to summarize data, whereas chi-square, independant samples t-test and One-Way ANOVA were used to compare groups by SPSS 15.0 statistical package programme. RESULTS: In the study, all of the taxi drivers (n=173 were male with a mean age of 39.2±9.6 years. Of the drivers, 58.4% were current smokers, whereas 75.1% were exposed to enviromental tobacco smoke. The frequency of indoor smoking in the taxi stations, taxis and drivers’ homes were 48.0%, 45.1%, and 59.0%, respectively. The mean breath CO level of the drivers was 16.9±12.8 ppm. CO level was positively associated with the current smoking status, total years of smoking, number of cigarettes smoked per day and passive exposure to tobacco smoke, whereas the association was negative with the elapsed time from the last cigarette smoked (p0.05. CONCLUSION: Results of the study provide evidence in support of the previous literature that smoking is one of the most important sources of carbonmonoxide. Interventions such as awareness raising trainings, referral of smokers willing to quit smoking to smoking cessation centers and screening programmes for smoking related diseases are needed to be implemented in collaboration with the relevant drivers’ associations. [TAF Prev Med Bull 2010; 9(6.000: 591-596

Distribution of Total Volatile Organic Compounds at taxi drivers in Tehran

Directory of Open Access Journals (Sweden)

Seyyed Mohammad Javad Golhosseini

2015-06-01

Full Text Available Air pollution is currently the most serious environmental health threat worldwide. Volatile Organic Compounds (VOC are considered as the main effective factors in causing air pollution. Vehicles are among the major sources which emit these compounds, so it seems that automobiles’ microenvironment is one of the places where people are exposed to high concentration of VOC. Evaluating the exposure amount of Total Volatile Organic Compounds (TVOC can indeed be used as an indicator to estimate the amount of exposure to every individual VOC. This study was conducted on the concentration of TVOC inside Tehran taxies for a period of one year. For this purpose, a real time instrument equipped with photo-ionization detector (PID was used. Consequently, the highest and the lowest measured TVOC in taxies equaled 3.33 ppm and 0.72 ppm, respectively. In addition, the arithmetic mean of TVOC concentration was 1.77±0.53 ppm inside the examined taxies. In this study, the parameters like measurement time, climate and vehicle conditions were found to have significant effect on the amount of exposure to TVOC.

Minibus taxi drivers’ sexual beliefs and practices associated with HIV infection and AIDS in KwaZulu- Natal, South Africa

Directory of Open Access Journals (Sweden)

Busisiwe Ncama

2013-01-01

Full Text Available Risky sexual behaviours in South Africa are a major contributing factor to the spread of HIV infection and AIDS. HIV infection amongst minibus taxi drivers is a concern, because these people belong to an occupational group that exhibits risky behaviours due to the demands of their work. Given the high vulnerability of minibus taxi drivers, exploring the sexual beliefs and health-related sexual practices of this group will assist in planning targeted interventions.The objectives of this study were to assess the level of knowledge, beliefs and practices regarding HIV infection and AIDS amongst minibus taxi drivers. An exploratory descriptive study was conducted using a pre-tested questionnaire to explore and describe sexual beliefs and practices associated with HIV infection and AIDS in a convenience sample of 175 minibus taxi drivers. Permission to undertake the study was obtained from the KwaZulu-Natal Taxi Alliance and individuals who participated in the study. Data analysis were analysed using the Statistical Package for Social Sciences 13.0. The study revealed that minibus taxi drivers are one of the high- risk groups in the spread of HIV infection and AIDS; they lack necessary education and need attention in relation to control and prevention of the spread of HIV and AIDS. Multiple sexual partners are relatively common amongst the minibus taxi drivers. Violence against women and even forceful sexual intercourse in the belief that women should tolerate it to keep the family together was reported. There is a need for intervention programmes with a focus on minibus taxi drivers and similar high-risk groups. Prevention activities should incorporate the distribution of condoms amongst this group and HIV prevention educational programmes, as well as creating mechanisms for accessing circumcision by the minibus taxi drivers.

Wormholes, warp drives and energy conditions

CERN Document Server

2017-01-01

Top researchers in the field of gravitation present the state-of-the-art topics outlined in this book, ranging from the stability of rotating wormholes solutions supported by ghost scalar fields, modified gravity applied to wormholes, the study of novel semi-classical and nonlinear energy conditions, to the applications of quantum effects and the superluminal version of the warp drive in modified spacetime. Based on Einstein's field equations, this cutting-edge research area explores the more far-fetched theoretical outcomes of General Relativity and relates them to quantum field theory. This includes quantum energy inequalities, flux energy conditions, and wormhole curvature, and sheds light on not just the theoretical physics but also on the possible applications to warp drives and time travel. This book extensively explores the physical properties and characteristics of these 'exotic spacetimes,' describing in detail the general relativistic geometries that generate closed timelike curves.

Hohlraums energy balance and x-ray drive

International Nuclear Information System (INIS)

Kilkenny, J.D.

1994-01-01

For many years there has been an active ICF program in the US concentrating on x-ray drive. X-ray drive is produced by focusing laser beams into a high Z hohlraum. Conceptually, the radiation field comes close to thermodynamic equilibrium, that is it becomes isotropic and Planckian. These properties lead to the benefits of x-ray drive--it is relatively easy to obtain drive symmetry on a capsule with no small scalelengths drive perturbations. Other advantages of x-ray drive is the higher mass ablation rate, leading to lower growth rates for hydrodynamic instabilities. X-ray drive has disadvantages, principally the loss of energy to the walls of the hohlraum. This report is divided into the following sections: (1) review of blackbody radiation; (2) laser absorption and conversion to x-rays; (3) x-ray absorption coefficient in matter and Rosseland mean free path; (4) Marshak waves in high Z material; (5) x-ray albedo; and (6) power balance and hohlraum temperature

Talent in the taxi: a model system for exploring expertise.

Science.gov (United States)

Woollett, Katherine; Spiers, Hugo J; Maguire, Eleanor A

2009-05-27

While there is widespread interest in and admiration of individuals with exceptional talents, surprisingly little is known about the cognitive and neural mechanisms underpinning talent, and indeed how talent relates to expertise. Because many talents are first identified and nurtured in childhood, it can be difficult to determine whether talent is innate, can be acquired through extensive practice or can only be acquired in the presence of the developing brain. We sought to address some of these issues by studying healthy adults who acquired expertise in adulthood. We focused on the domain of memory and used licensed London taxi drivers as a model system. Taxi drivers have to learn the layout of 25,000 streets in London and the locations of thousands of places of interest, and pass stringent examinations in order to obtain an operating licence. Using neuropsychological assessment and structural and functional magnetic resonance imaging, we addressed a range of key questions: in the context of a fully developed brain and an average IQ, can people acquire expertise to an exceptional level; what are the neural signatures, both structural and functional, associated with the use of expertise; does expertise change the brain compared with unskilled control participants; does it confer any cognitive advantages, and similarly, does it come at a cost to other functions? By studying retired taxi drivers, we also consider what happens to their brains and behaviour when experts stop using their skill. Finally, we discuss how the expertise of taxi drivers might relate to the issue of talent and innate abilities. We suggest that exploring talent and expertise in this manner could have implications for education, rehabilitation of patients with cognitive impairments, understanding individual differences and possibly conditions such as autism where exceptional abilities can be a feature.

Minibus taxi drivers’ sexual beliefs and practices associated with HIV infection and AIDS in KwaZulu- Natal, South Africa

Directory of Open Access Journals (Sweden)

Busisiwe Ncama

2013-01-01

The objectives of this study were to assess the level of knowledge, beliefs and practices regarding HIV infection and AIDS amongst minibus taxi drivers. An exploratory descriptive study was conducted using a pre-tested questionnaire to explore and describe sexual beliefs and practices associated with HIV infection and AIDS in a convenience sample of 175 minibus taxi drivers. Permission to undertake the study was obtained from the KwaZulu-Natal Taxi Alliance and individuals who participated in the study. Data analysis were analysed using the Statistical Package for Social Sciences 13.0. The study revealed that minibus taxi drivers are one of the high- risk groups in the spread of HIV infection and AIDS; they lack necessary education and need attention in relation to control and prevention of the spread of HIV and AIDS. Multiple sexual partners are relatively common amongst the minibus taxi drivers. Violence against women and even forceful sexual intercourse in the belief that women should tolerate it to keep the family together was reported. There is a need for intervention programmes with a focus on minibus taxi drivers and similar high-risk groups. Prevention activities should incorporate the distribution of condoms amongst this group and HIV prevention educational programmes, as well as creating mechanisms for accessing circumcision by the minibus taxi drivers.

Les aspects matériels de la taxis byzantine The material aspects of the Byzantine taxis

Directory of Open Access Journals (Sweden)

Marie‑France Auzépy

2008-06-01

Full Text Available La taxis grecque – correspondant exact de l’ordo latin – est un aspect essentiel de la civilisation byzantine : elle organise cette société de manière à ce que celle-ci soit un reflet aussi exact que possible de la société céleste, décrite en particulier par Denys l’Aréopagite. La taxis est donc à la fois précise et contraignante et nous a été transmise dans des livres décrivant le protocole : le De Cerimoniis au Xe siècle, le Traité du pseudo-Kodinos au XIVe siècle. Au cours de cérémonies où tous les aspects matériels – l’habit, la couronne, le trône, les acclamations à la gloire de l’empereur, l’orgue qui les accompagne, les gestes accomplis par l’empereur comme par ceux qui l’entourent – ont un sens, l’Empire byzantin affirme ainsi son équilibre et sa qualité de peuple élu. Jusqu’en 1204, les autres nations ont jalousé la qualité que s’était octroyée l’Empire romain d’Orient : celle d’image de la cour céleste, qui est figurée dans le cérémonial. Cette jalousie a pris d’autres formes après 1453, et l’on s’intéressera aux souverains européens qui, tel Louis XIV, ont voulu faire figure d’héritiers de l’empire défunt et relever ses cérémonies.The Greek taxis(order– the exact equivalent of the Latin ordo – is an essential aspect of Byzantine civilization: it organized society in such a way that it would reflect the celestial society as closely as possible, as has been described by Dionysius the Areopagite. The taxis is therefore both precise and restrictive and has been passed down to us through writings describing the protocol: the De Cerimoniis in the tenth century and the treatise of Pseudo-Kodinos in the fourteenth century. Through ceremonies in which all the material aspects have a meaning – the dress, the crown, the throne, the proclaiming of the glory of the emperor, the accompanying organ, the gestures of the emperor and of those around

Superluminal warp drive and dark energy

Energy Technology Data Exchange (ETDEWEB)

Gonzalez-Diaz, Pedro F. [Colina de los Chopos, Centro de Fisica ' Miguel A. Catalan' , Instituto de Matematicas y Fisica Fundamental, Consejo Superior de Investigaciones Cientificas, Serrano 121, 28006 Madrid (Spain)], E-mail: p.gonzalezdiaz@imaff.cfmac.csic.es

2007-11-29

In this Letter we consider a warp drive spacetime where the spaceship can only travel faster than light. Restricting to the two-dimensional case, we find that if the warp drive is placed in an accelerating universe the warp bubble size increases in a comoving way to the expansion of the universe in which it is immersed. Also shown is the result that the apparent velocity of the ship steadily increases with time as phantom energy is accreted onto it.

An open-data approach for quantifying the potential of taxi ridesharing

DEFF Research Database (Denmark)

Barann, Benjamin; Beverungen, Daniel; Müller, Oliver

2017-01-01

greenhouse gas emissions. We develop a one-to-one TRS approach that matches rides with similar start and end points. We evaluate our approach by analyzing an open dataset of > 5 million taxi trajectories in New York City. Our empirical analysis reveals that the proposed approach matches up to 48.34% of all...... taxi rides, saving 2,892,036 km of travel distance, 231,362.89 l of gas, and 532,134.64 kg of CO2 emissions per week. Compared to many-to-many TRS approaches, our approach is competitive, simpler to implement and operate, and poses less rigid assumptions on data availability and customer acceptance....

The influence of fixed-route taxi on road accidents and air pollution

Directory of Open Access Journals (Sweden)

V. Fedotov

2006-03-01

Full Text Available The development of market economy in Russia expands the need for movement of groups of people of large mega cities on time to a place at simultaneous reduction of the number of groups with identical purposes. Therefore for many cities a wide use of fixed-route taxis the service of passengers at a constant increase of the numbers of routes and the numbers of transport units was characteristic. At the certain intensity of the movement of fixed-route taxis on separate sites of city highways the transport stream and the changing quality of environment raises the risk of road accident and becomes ecologically unsafe. The results of the estimation of the negative influence of fixed-route taxis in comparison with other categories of vehicles are presented. The research was made on city highways running through the zones with a greater number of cultural and community places, shopping centers and administrative establishments. Perspective ways of the increase of traffic safety and the decrease of concentration of harmful emissions are offered.

Health Status, Intention to Seek Health Examination, and Participation in Health Education Among Taxi Drivers in Jinan, China

Science.gov (United States)

Yang, Yan; Fan, Xiao-sheng; Tian, Cui-huan; Zhang, Wei; Li, Jie; Li, Shu-qing

2014-01-01

Background: Taxi drivers are exposed to various risk factors such as work overload, stress, an irregular diet, and a sedentary lifestyle, which make these individuals vulnerable to many diseases. This study was designed to assess the health status of this occupational group. Objectives: The objective was to explore the health status, the intention to seek health examination, and participation in health education among taxi drivers in Jinan, China. Patients and Methods: The sample-size was determined scientifically. The systematic sampling procedure was used for selecting the sample. Four hundred taxi drivers were randomly selected from several taxi companies in Jinan. In total, 396 valid questionnaires (from 370 males and 26 females) were returned. Health status, intention to seek health examination, and participation in health education were assessed by a self-designed questionnaire. Other personal information including sex, age, ethnicity, marital status, years of employment as a taxi driver, education level, and habits were also collected. Results: This survey revealed that 54.8% of taxi drivers reported illness in the last two weeks and 44.7% of participants reported chronic diseases. The prevalence rates of hypertension, diabetes mellitus, gastroenteritis, arthritis, and heart disease were 18.2%, 8.8%, 26%, 18.4%, and 4.8% of questioned taxi drivers, respectively. Significant self-reported symptoms included fatigue, waist and back pain, headache, dyspepsia, and dry throat affecting 49.7%, 26.2%, 23.5%, 26%, and 27% of participants, respectively. In total, 90.1% of subjects thought that it was necessary to receive a regular health examination. Only 17.9% of subjects had been given information about health education, and significantly, more than 87% of subjects who had been given information about health education reported that the information had been helpful. Conclusions: Taxi drivers’ health was poor in our survey. Thus, using health education interventions

Taxi trips distribution modeling based on Entropy-Maximizing theory: A case study in Harbin city-China

Science.gov (United States)

Tang, Jinjun; Zhang, Shen; Chen, Xinqiang; Liu, Fang; Zou, Yajie

2018-03-01

Understanding Origin-Destination distribution of taxi trips is very important for improving effects of transportation planning and enhancing quality of taxi services. This study proposes a new method based on Entropy-Maximizing theory to model OD distribution in Harbin city using large-scale taxi GPS trajectories. Firstly, a K-means clustering method is utilized to partition raw pick-up and drop-off location into different zones, and trips are assumed to start from and end at zone centers. A generalized cost function is further defined by considering travel distance, time and fee between each OD pair. GPS data collected from more than 1000 taxis at an interval of 30 s during one month are divided into two parts: data from first twenty days is treated as training dataset and last ten days is taken as testing dataset. The training dataset is used to calibrate model while testing dataset is used to validate model. Furthermore, three indicators, mean absolute error (MAE), root mean square error (RMSE) and mean percentage absolute error (MPAE), are applied to evaluate training and testing performance of Entropy-Maximizing model versus Gravity model. The results demonstrate Entropy-Maximizing model is superior to Gravity model. Findings of the study are used to validate the feasibility of OD distribution from taxi GPS data in urban system.

Comparison between internal combustion engines and simulated electrical propulsion of taxis; Vergleich zwischen verbrennungsmotorischem und simuliertem elektrischen Antrieb von Taxis

Energy Technology Data Exchange (ETDEWEB)

Wallner, Stefan [Stefan Wallner Energietechnik, Unterhaching (Germany); Thym, Jochen

2011-03-15

The term 'triumphal procession of electromobility' produces an enormous expectation at the end users side, but intensive development work has still to be done. The transition from today's vehicles towards electric propulsion is not to be expected to take place overnight but will start with slot applications. Energietechnik Wallner has analysed the potential of taxis. (orig.)

Energy self-sufficient sensory ball screw drive; Energieautarker sensorischer Kugelgewindetrieb

Energy Technology Data Exchange (ETDEWEB)

Bertram, Oliver

2012-07-01

Nowadays the availability of machine tools plays a decisive role in competition to increase in productivity. From state of the art it arises, that ball screw drives are the most abusive component in feed drives because of abrasive wear. Furthermore condition monitoring enables avoiding unplanned machine failure and increasing the availability of the deployed production facility. Thereby the application of additional sensors allows the direct acquisition of wear correlative measurements. To reduce the required effort for integration and increase the robustness, reliability and clarity in industrial environment energy self-sufficient sensor systems can be applied. In this thesis the development and investigation of an energy self-sufficient sensory ball screw drive with direct measurement of wear correlative pretension for condition monitoring application is described. The prototype measures the pretension with force sensors based on strain gauges. The sensor system includes microcontroller-based electronics for signal processing as well as wireless data transmission with ZigBee-standard. A hybrid system assures the energy supply of the sensor system. On the one hand a stepper motor generator produces electrical energy from the motion energy of the ball screw drive. On the other hand an energy buffer based on super caps is reloaded in stationary position by wireless energy transmission. For verification a prototype system is build up. In measurements the sensory and energetic characteristics of the energy self-sufficient sensor systems are analyzed. Moreover, the functionality of the ball screw drive as well as the signal characteristics of the force sensors are examined for different pretensions. In addition, pretension losses due to wear are established in realized endurance trials, which means that timely maintenance can be planned.

INFLUENCE OF SERVICE QUALITY AND FARE TOWARD CUSTOMER SATISFACTION AND ITS IMPACT ON CUSTOMER LOYALTY OF EXPRESS TAXI IN JAKARTA

Directory of Open Access Journals (Sweden)

Mohammad Rizan

2015-09-01

Full Text Available The purpose of this study was to: to examine empirically the effect of service quality to customer satisfaction on Express taxi, to examine empirically the effect of fare to customer satisfaction on Express taxi, to examine empirically the effect of customer satisfaction to customer loyalty on Express taxi, to examine empirically the effect of service quality to customer loyalty on Express taxi, and to examine empirically the effect of fare to customer loyalty on Express taxi. Data collection using survey methods. Sample of this study are 200 respondents who have using services of Express taxi more than two times in last three months. Data analysis using SPSS version 23 and SEM (Structural Equation Modeling LISREL version 8.7. Results of hypothesis testing showed: service quality have positive and significant effect on customer satisfaction, fare have positive and significant effect on customer satisfaction, customer satisfaction have positive and significant effect on customer loyalty, service quality have positive and not significant effect to on customer loyalty. fare have positive and significant effect to on customer loyalty. Rated fit model with value of RMSEA 0.043, value of RMR 0.043, value of CMIN/DF 1.88, value of NFI 0.96, value of NNFI 0.98, and value of CFI 0.98. The results of this research beneficial to transportation company, especially Express taxi in Jakarta, to create better strategy in improving customer loyalty.

Research on the Coordinated Design of Bus and Taxi Station

Directory of Open Access Journals (Sweden)

Jiangfeng Xi

2015-01-01

Full Text Available Rises in the number of transit buses, bus routes, and overall traffic volume in China’s cities, coupled with interference from other transport modes, such as taxis loading and unloading passengers nearby, have led to increasing traffic delays at bus stops, which is considered one of the factors degrading service levels and traffic operations on urban roadways. This paper studies traffic characteristics at bus stops, investigates variations in delay from different types or designs of bus stops, and analyzes the impact of it on traffic capacity, the purpose of which is to propose a solution to predicting the feasibility of an integrated design of bus stops and taxi stands with the help of mathematical models and based on the objectives of optimal traffic operations and passenger transfer.

THE ROUTE DETERMINATION OF FILING A TAXI TO THE CUSTOMER IN TERMS OF FUNCTIONING OF THE AUTOMATED CONTROL SYSTEM

Directory of Open Access Journals (Sweden)

Yu. O. Davidich

2008-03-01

Full Text Available The issues of overall performance increase of taxi transport due to improvement of automated system of dispatching management by its technological processes are considered. The route of taxi submission to a customer is offered to be determined by a criterion of minimum time. To solve the given task the taxi submission route determination technique is developed. It will promote the reduction of passengers’ waiting time and the decrease in operational expenses of a carrier.

Study on the effect of driving cycles on energy efficiency of electric vehicles

Energy Technology Data Exchange (ETDEWEB)

Ji Fenzhu; Xu Licong [School of Transportation Science and Engineering of Beihang Univ., BJ (China); Wu Zhixin [Tianjin Qing Yuan Electric Vehicle Corp. Ltd., TJ (China)

2009-07-01

The energy usage efficiency of electric vehicles (EVS) and evaluation index of electromotor efficiency were studied. The idea of ''interval usage percentage of energy efficiency'' and ''exertion degree of energy efficiency'' of electromotor was brought forward. The effect of driving cycles on the distribution of running status of electromotor and its efficiency was investigated. The electromotor efficiency and the variety trend of average driving force at different driving cycles were discussed. Based on several typical domestic and foreign driving cycles, the exertion degree of energy efficiency and the whole efficiency of power train on some types of EVS were analyzed and calculated. The result indicates that there is a difference of 9.64% in exertion degree of energy efficiency of electromotor at different driving cycles. The efficiency distribution of electromotor and control system is different, and the average driving force is different, too. That cause the great variety in driving range. The idiographic reference data are provided to the establishment of driving cycles' criterion of EVS in our country. (orig.)

Automation of orders in taxi service

OpenAIRE

Simčič, Matej

2012-01-01

Automation is rapidly growing in the last years. The advantages it brings are cost reduction, faster and better performance of tasks that would be otherwise done by humas. It began in the manufacturing industry and later expanded to other sectors. Today's technology allows the implementation of automation in a wide range of areas. The thesis deals with the implementation of a system that allows automated ordering of a taxi. The system consists of four components. They are two mobile app...

Driving factors for the regional implementation of renewable energy ‐ A multiple case study on the German energy transition

International Nuclear Information System (INIS)

Lutz, Lotte Marie; Fischer, Lisa-Britt; Newig, Jens; Lang, Daniel Johannes

2017-01-01

Understanding what drives the regional implementation of renewable energy is a prerequisite for energy transitions toward a post-fossil-based energy economy. This paper presents an empirical analysis of driving factors for the regional implementation and use of renewable energy. We tested literature-derived driving factors in a comparative analysis of 18 selected study regions using Rough Set Analysis and performance analysis. We paid special attention to common combinations of driving factors, which we understand as established practices concerning the use and implementation of renewable energy. Our findings confirm most of the driving factors identified in the literature, for example the existence of key actors, knowledge exchange, or the use of goals and milestones. We also observe differences in key driving factors between highly successful and less successful regions, especially regarding funding opportunities. The results may support policy makers who aim to successfully implement renewable energy at a regional level. - Highlights: • We analyzed driving factors for RE implementation in 18 best-practice regions. • Most driving factors from transition and governance literature were confirmed. • We identified common successful practices concerning RE implementation.

Use of the renewable wind and photovoltaic sources, for the recharge of a fleet of electric taxis in Havana, Cuba

International Nuclear Information System (INIS)

Sánchez Torres, Yamir

2017-01-01

Electrification of the transportation sector seems to be one of the alternatives in terms of restriction of pollutant from that sector. However, it is necessary to study the GHG (Green House Gas) emissions from Generation Power Plants (EGPP) because could be more or less the same of that from the vehicles. Furthermore, Centralized GPP supply would result in distribution losses, bigger fuel consumption and more pollution. Thus, EVs development should be considered as a sustainable solution if powered by electricity systems with considerable share of Renewable Energy Sources (RES). In this paper, the study of the recharge of an EV taxi fleet during night, using photovoltaic and wind mills RES in Havana, Cuba, is analyzed. This work is aiming to find a feasible operational synergy between cited intermittent RES electricity generation and EVs taxi fleet recharge. (author)

76 FR 65769 - Application of Friendship Airways, Inc. d/b/a Yellow Air Taxi for Commuter Authority

Science.gov (United States)

2011-10-24

... DEPARTMENT OF TRANSPORTATION Office of the Secretary Application of Friendship Airways, Inc. d/b/a Yellow Air Taxi for Commuter Authority AGENCY: Department of Transportation. ACTION: Notice of Order to... issued to Friendship Airways, Inc. d/b/a Yellow Air Taxi and deny its application to resume commuter...

A hybrid life cycle and multi-criteria decision analysis approach for identifying sustainable development strategies of Beijing's taxi fleet

International Nuclear Information System (INIS)

Cai, Yanpeng; Applegate, Scott; Yue, Wencong; Cai, Jianying; Wang, Xuan; Liu, Gengyuan; Li, Chunhui

2017-01-01

To identify and evaluate sustainable strategies of taxi fleet in Beijing in terms of economic, policy, and environmental implications, a hybrid approach was developed through incorporating multi-criteria decision analysis (MCDA) methods within a general life-cycle analysis (LCA) framework. The approach can (a) help comprehensive evaluate environmental impacts of multiple types of vehicles, (b) facilitate analysis of environmental, economic and policy features of such vehicles, and (c) identify desirable taxi fleet development strategies for the city. The developed approach represented an improvement of the decision-making capability for taxi implementation based on multiple available technologies and their performance that can be specifically tailored to Beijing. The results demonstrated that the proposed approach could comprehensively reflect multiple implications of strategies for the taxi fleet in Beijing to reduce air pollution in the city. The results also indicated that the electric vehicle powered with the year 2020 electricity projections would be the ideal solution, outranking the other alternatives. The conventional vehicle ranked the lowest among the alternatives. The plug-in hybrid vehicle powered by 2020 electricity projects ranked the third, followed by the plug-in hybrid vehicle ranking the fourth, and the hybrid vehicle ranking the fifth. - Highlights: • An hybrid approach was proposed for evaluating sustainable strategies of Beijing's taxi fleet. • This approach was based on the combination of multi-criteria decision analysis methods and life-cycle assessment. • Environmental, economic and policy performances of multiple strategies were compared. • Detailed responses of taxi drivers and local residents were interviewed. • The electric vehicle would be the ideal solution for Beijing Taxi fleet.

Predicting Taxi-Out Time at Congested Airports with Optimization-Based Support Vector Regression Methods

Directory of Open Access Journals (Sweden)

Guan Lian

2018-01-01

Full Text Available Accurate prediction of taxi-out time is significant precondition for improving the operationality of the departure process at an airport, as well as reducing the long taxi-out time, congestion, and excessive emission of greenhouse gases. Unfortunately, several of the traditional methods of predicting taxi-out time perform unsatisfactorily at congested airports. This paper describes and tests three of those conventional methods which include Generalized Linear Model, Softmax Regression Model, and Artificial Neural Network method and two improved Support Vector Regression (SVR approaches based on swarm intelligence algorithm optimization, which include Particle Swarm Optimization (PSO and Firefly Algorithm. In order to improve the global searching ability of Firefly Algorithm, adaptive step factor and Lévy flight are implemented simultaneously when updating the location function. Six factors are analysed, of which delay is identified as one significant factor in congested airports. Through a series of specific dynamic analyses, a case study of Beijing International Airport (PEK is tested with historical data. The performance measures show that the proposed two SVR approaches, especially the Improved Firefly Algorithm (IFA optimization-based SVR method, not only perform as the best modelling measures and accuracy rate compared with the representative forecast models, but also can achieve a better predictive performance when dealing with abnormal taxi-out time states.

The Effect of Working Conditions to the Health Status in Taxi and Bus Drivers in Canakkale, Turkey; Community Based Study

Directory of Open Access Journals (Sweden)

Aysegul Uludag

2016-04-01

Full Text Available Aim: The growing taxi and bus driver workforce is at risk for poor health status, obesity, hypertension, metabolic syndrome and with increased risk for cardiovascular disease. We aimed to determine the relationship between working conditions and health status in taxi and bus drivers. Material and Method: This study is a descriptive study. The population of the study was taxi and bus drivers in central of Canakkale. There were total 250 taxi and bus drivers who registered in The Chamber of Canakkale Drivers and Vehicle. We reached the 70 taxi drivers and 93 bus drivers. The participants were visited at their workplace. We performed the questionnaire that include the socio-demografic features, habits, the working conditions. We evaluated the blood pressure, waist-hip measurements and capillary blood glucose at any time. Results: Total of the 163 men drivers were enrolled the study. Nine (12.9% taxi drivers and 6 (6.5% bus drivers were hipertensive, and 1 taxi driver and 2 bus drivers with random capillary blood glucose levels higher than 200 mg. The prevalence of hypertension was 9.2%, diabetes mellitus was 1.8, obesity was 49.4%. Discussion: Drivers have many risk factors for CVD like stress and immobility. In our study, the socio-demografic and working conditions are limited for explaining the risk for hipertension, diabetes mellitus and obesity in drivers in Canakkale. These study have to be done in metropolitan cities. In this aspect, the drivers can be evaluated in their own living spaces and working conditions.

The Aircraft Electric Taxi System: A Qualitative Multi Case Study

Science.gov (United States)

Johnson, Thomas Frank

The problem this research addresses is the airline industry, and the seemingly unwillingness attitude towards adopting ways to taxi aircraft without utilizing thrust from the main engines. The purpose of the study was to get a better understanding of the decision-making process of airline executives, in respect to investing in cost saving technology. A qualitative research method is used from personal interviews with 24 airline executives from two major U.S. airlines, related industry journal articles, and aircraft performance data. The following three research questions are addressed. RQ1. Does the cost of jet fuel influence airline executives' decision of adopting the aircraft electric taxi system technology? RQ2 Does the measurable payback period for a return on investment influence airline executives' decision of adopting ETS technology? RQ3. Does the amount of government assistance influence airline executives' decision of adopting ETS technology? A multi case research study design is used with a triangulation technique. The participant perceptions indicate the need to reduce operating costs, they have concerns about investment risk, and they are in favor of future government sponsored performance improvement projects. Based on the framework, findings and implications of this study, a future research paper could focus on the positive environmental effects of the ETS application. A study could be conducted on current airport area air quality and the effects that aircraft main engine thrust taxiing has on the surrounding air quality.

Using an innovative price model to leverage the business model – The case of price model innovation in the largest Swedish taxi company

Directory of Open Access Journals (Sweden)

Carl-Johan Petri

2014-08-01

Full Text Available Purpose: The purpose of the paper is to describe how the biggest Swedish taxi company (Taxi Kurir developed an innovative price model to leverage the business model. Design/methodology/approach : The empirical data in the article describe Taxi Kurir’s development of a new price model. Data about the Swedish taxi market and about Taxi Kurir has been compiled though interviews and document studies. Detailed information about the background, development and implementation of Taxi Kurir’s new price model has been captured through interviews with representatives from Taxi Kurir. Findings : Based on both the empirical example, and other investigations, we have found that a company can create substantial changes in their price model, by just changing some of its basic characteristics. A well designed price model can contribute to leveraging the intentions of the business model. Practical implications : Most academic and practical texts about business models consider pricing to be an important component. However, they typically do not refer to the specifics of the price- or revenue models. According to the literature review in this paper, and the empirical findings, the configuration of a company’s price model should be aligned with its business model. This will contribute to leveraging the business model. Originality/value: The Swedish taxi market is one of the most deregulated in the world. Differently from most other countries, any individual or company can start and operate a taxi business. This case offers a unique description on how the biggest company in the market responded to the competition by introducing a fundamentally new price model, by making a small change in one of the dimensions in their existing price model.

Aggression, emotional self-regulation, attentional bias, and cognitive inhibition predict risky driving behavior.

Science.gov (United States)

Sani, Susan Raouf Hadadi; Tabibi, Zahra; Fadardi, Javad Salehi; Stavrinos, Despina

2017-12-01

The present study explored whether aggression, emotional regulation, cognitive inhibition, and attentional bias towards emotional stimuli were related to risky driving behavior (driving errors, and driving violations). A total of 117 applicants for taxi driver positions (89% male, M age=36.59years, SD=9.39, age range 24-62years) participated in the study. Measures included the Ahwaz Aggression Inventory, the Difficulties in emotion regulation Questionnaire, the emotional Stroop task, the Go/No-go task, and the Driving Behavior Questionnaire. Correlation and regression analyses showed that aggression and emotional regulation predicted risky driving behavior. Difficulties in emotion regulation, the obstinacy and revengeful component of aggression, attentional bias toward emotional stimuli, and cognitive inhibition predicted driving errors. Aggression was the only significant predictive factor for driving violations. In conclusion, aggression and difficulties in regulating emotions may exacerbate risky driving behaviors. Deficits in cognitive inhibition and attentional bias toward negative emotional stimuli can increase driving errors. Predisposition to aggression has strong effect on making one vulnerable to violation of traffic rules and crashes. Copyright © 2017 Elsevier Ltd. All rights reserved.

Modeling of the service taxi

Directory of Open Access Journals (Sweden)

R. M. Bezborodnikova

2016-01-01

Full Text Available Modeling and optimization business processes are ongoing challenges of modernity. Based on the study of business processes to anticipate and avoid many problems in the work of companies linked primarily with an increased level of costs, the low quality of the performed works and manufactured products, excessive run time functions. Application of simulation tool for business processes allows at the stage of planning to assess various indicators of the effectiveness of processes to identify the best sequence of functions, determine resource costs to calculate personnel workload, thereby facilitating timely adoption of the correct administrative decisions. The article deals with the modeling of the business process “Order processing” taxi service Heat the city of Orenburg. Based on the methodology of modeling Business Process Model and Notation (BPMN built functional diagram of the business process (with freely distributed software product Bizagi Modeler, given the resources used, the costs of their use, built calendar schedules. Next, the operation was carried out simulations with different process input data: the number of incoming applications, the number of controllers and advertising budget. It is shown that the efficiency of the business process will contribute to the increase in the total number of dispatchers up to 6 people, as well as increasing advertising costs doubled. As a result of the decisions taken is expected to increase the net income of the company to 76 794 RUR and the average salary of the staff (in particular taxi drivers to 42 281 RUR, dispatchers and 22 799 RUR, as well as reducing the duration of processing a single order up to 31 minutes.

The xylanase inhibitor TAXI-III counteracts the necrotic activity of a Fusarium graminearum xylanase in vitro and in durum wheat transgenic plants.

Science.gov (United States)

Moscetti, Ilaria; Faoro, Franco; Moro, Stefano; Sabbadin, Davide; Sella, Luca; Favaron, Francesco; D'Ovidio, Renato

2015-08-01

The xylanase inhibitor TAXI-III has been proven to delay Fusarium head blight (FHB) symptoms caused by Fusarium graminearum in transgenic durum wheat plants. To elucidate the molecular mechanism underlying the capacity of the TAXI-III transgenic plants to limit FHB symptoms, we treated wheat tissues with the xylanase FGSG_03624, hitherto shown to induce cell death and hydrogen peroxide accumulation. Experiments performed on lemmas of flowering wheat spikes and wheat cell suspension cultures demonstrated that pre-incubation of xylanase FGSG_03624 with TAXI-III significantly decreased cell death. Most interestingly, a reduced cell death relative to control non-transgenic plants was also obtained by treating, with the same xylanase, lemmas of TAXI-III transgenic plants. Molecular modelling studies predicted an interaction between the TAXI-III residue H395 and residues E122 and E214 belonging to the active site of xylanase FGSG_03624. These results provide, for the first time, clear indications in vitro and in planta that a xylanase inhibitor can prevent the necrotic activity of a xylanase, and suggest that the reduced FHB symptoms on transgenic TAXI-III plants may be a result not only of the direct inhibition of xylanase activity secreted by the pathogen, but also of the capacity of TAXI-III to avoid host cell death. © 2014 BSPP AND JOHN WILEY & SONS LTD.

Outsourcing of Defense Supply Center, Columbus, Bus and Taxi Service Operations

National Research Council Canada - National Science Library

Granetto, Paul

1999-01-01

Introduction. We performed the audit in response to allegations to the Defense Hotline that the Defense Supply Center, Columbus, outsourcing study for bus and taxi service operations was based on incorrect methodology...

Factor Analysis of Passenger Cars Using as a Taxi

Directory of Open Access Journals (Sweden)

Deriugin O.V.

2016-05-01

Full Text Available A procedure to select passenger cars has been proposed. The procedure helps substantiate choice of effective transportation means in accordance with taxi class to meet consumption requirements of those taking part in transportation process from the viewpoint of comfort, safety, and minimum expenditures in the context of such transportation type.

Spatio-temporal pattern formation in predator-prey systems with fitness taxis

DEFF Research Database (Denmark)

Heilmann, Irene T.; Thygesen, Uffe Høgsbro; Sørensen, Mads Peter

2018-01-01

We pose a spatial predator–prey model in which the movement of animals is not purely diffusive, but also contains a drift term in the direction of higher specific growth rates. We refer to this as fitness taxis. We conduct a linear stability analysis of the resulting coupled reaction–advection–di......We pose a spatial predator–prey model in which the movement of animals is not purely diffusive, but also contains a drift term in the direction of higher specific growth rates. We refer to this as fitness taxis. We conduct a linear stability analysis of the resulting coupled reaction...... of diffusive motion, is ecologically plausible, and provides an alternative mechanism for formation of patterns in spatially explicit ecosystem models, with emphasis on non-stationary spatio-temporal dynamics....

Development of ATC Tower Systems: Electronic Flight Strip System at LKPR and the Implementation of TAXI Milestone to SUM

Directory of Open Access Journals (Sweden)

Pavel Černý

2016-10-01

Full Text Available This article describes the Electronic Flight Strip System used at Václav Havel Airport Prague and presents the results of an analysis of the clearance input from ATCOs. The outcomes indicate that various clearances are frequently issued together in a common time frame, usually depending on the traffic flow structure. The focus then moves towards the implementation of the TAXI milestone into the Start-Up Manager. The used statistic methods indicate that the amount of TTOT recalculations after AOBT decreases, but not significantly. However, the accuracy of TTOT after TAXI clearance is considerably better. The mean and most common deviation of ATOT from TTOT after the implementation of TAXI milestone is -1 minute. The results are challenged and confirmed by a further analysis of the TTOT-ATOT difference regarding individual stand/RWY pairs. The results may be used to adjust the assumed taxi times.

Distracted driving: mobile phone use while driving in three Mexican cities.

Science.gov (United States)

Vera-López, Juan Daniel; Pérez-Núñez, Ricardo; Híjar, Martha; Hidalgo-Solórzano, Elisa; Lunnen, Jeffrey C; Chandran, Aruna; Hyder, Adnan A

2013-08-01

Mexico has a significant road traffic injury and mortality burden, and several states/municipalities have begun passing legislation restricting mobile phone use while driving (MPUWD). Little information is available about the prevalence of MPUWD in Mexico. This study measures the prevalence of mobile phone talking and texting among drivers in three cities, and identifies associated demographic and environmental factors. Two rounds of roadside observations from a group of randomly selected automobile drivers were conducted during 2011-2012 in Guadalajara-Zapopan, León and Cuernavaca. The overall prevalence of MPUWD was 10.78%; it was highest in Guadalajara-Zapopan (13.93%, 95% CI 12.87 to 15.05), lowest in Cuernavaca (7.42%, 95% CI 6.29 to 8.67), and remained stable over two rounds of observations, except for León, where the prevalence increased from 5.27% to 10.37% (p=0.000). Driving alone on major roads in non-taxi cars during the weekdays was associated with MPUWD. Results highlight the importance of studying the risk of mobile phone use, and designing and evaluating specific preventive interventions to address this problem in Mexico.

Open-wheel race car driving: energy cost for pilots.

Science.gov (United States)

Beaune, Bruno; Durand, Sylvain; Mariot, Jean-Pierre

2010-11-01

The aim of this study was to evaluate the energy cost of speedway open-wheel race car driving using actimetry. Eight pilot students participated in a training session consisting of 5 successive bouts of around 30 minutes driving at steady speed on the Bugatti speedway of Le Mans (France). Energy expenditure (EE, kcal) was determined continuously by the actimetric method using the standard equation. Energy cost was estimated through physical activity ratio (PAR = EE/BMR ratio, Mets) calculation after basal metabolism rate (BMR, kcal·min-1) estimation. A 1-met PAR value was attributed to the individual BMR of each volunteer. Bout durations and EE were not significantly different between driving bouts. Mean speed was 139.94 ± 2.96 km·h-1. Physical activity ratio values ranged 4.92 ± 0.50 to 5.43 ± 0.47 Mets, corresponding to a 5.27 ± 0.47-Mets mean PAR values and a 1.21 ± 0.41 kcal·min-1 mean BMR value. These results suggest that actimetry is a simple and efficient method for EE and PAR measurements in motor sports. However, further studies are needed in the future to accurately evaluate relationships between PAR and driving intensity or between PAR and race car type.

Labeling Residential Community Characteristics from Collective Activity Patterns Using Taxi Trip Data

Science.gov (United States)

Zhou, Y.; Fang, Z.

2017-09-01

There existing a significant social and spatial differentiation in the residential communities in urban city. People live in different places have different socioeconomic background, resulting in various geographically activity patterns. This paper aims to label the characteristics of residential communities in a city using collective activity patterns derived from taxi trip data. Specifically, we first present a method to allocate the O/D (Origin/Destination) points of taxi trips to the land use parcels where the activities taken place in. Then several indices are employed to describe the collective activity patterns, including both activity intensity, travel distance, travel time, and activity space of residents by taking account of the geographical distribution of all O/Ds of the taxi trip related to that residential community. Followed by that, an agglomerative hierarchical clustering algorithm is introduced to cluster the residential communities with similar activity patterns. In the case study of Wuhan, the residential communities are clearly divided into eight clusters, which could be labelled as ordinary communities, privileged communities, old isolated communities, suburban communities, and so on. In this paper, we provide a new perspective to label the land use under same type from people's mobility patterns with the support of big trajectory data.

Mobilizing private finance to drive an energy industrial revolution

International Nuclear Information System (INIS)

Mathews, John A.; Kidney, Sean; Mallon, Karl; Hughes, Mark

2010-01-01

While uptake of renewable energies as a solution to climate change is widely discussed, the issue of public vs. private financing is not yet adequately explored. The debates over the Kyoto Protocol and its successor, culminating in the COP15 Climate Change Conference in Copenhagen in December 2009, maintained a strong preference for public over private financing. Yet it is also clear to most observers that the energy revolution will never happen without the involvement of private finance to drive private investment. In this Viewpoint, we discuss the ways in which private financing could be mobilized to drive the energy industrial revolution that is needed if climate change mitigation is to succeed.

The share-a-ride problem : people and parcels sharing taxis

NARCIS (Netherlands)

Li, B.; Krushynskyi, D.; Reijers, H.A.; van Woensel, T.

2014-01-01

New city logistics approaches are needed to ensure efficient urban mobility for both people and goods. Usually, these are handled independently in dedicated networks. This paper considers conceptual and mathematical models in which people and parcels are handled in an integrated way by the same taxi

Exposure of bus and taxi drivers to urban air pollutants as measured by DNA and protein adducts

DEFF Research Database (Denmark)

Hemminki, K.; Zhang, L.F.; Krüger, J.

1994-01-01

Urinary 1-hydroxypyrene, lymphocyte DNA adducts, serum protein-bound PAH and hemoglobin-bound alkene adducts were analysed from 4 groups of non-smoking men: urban and suburban bus drivers, taxi drivers and suburban controls. The only differences between the groups were in DNA adducts between...... suburban bus drivers and controls, and in DNA adduct and plasma protein PAH-adducts between taxi drivers and controls....

Modeling with Robotran the autonomous electrical taxi and pushback operations of an Airbus A320

OpenAIRE

Quinet, Stéphane

2017-01-01

Nowadays, commercial flights are very close to a full automation while several means of transport already made the move. Civilian transport airplanes offer the possibility to fly in a fully automated mode from a few seconds after take-off to the exit of the runway - down to 60 knots- after landing. However, three flight sequences are not covered yet by an automated solution : the take-off, the taxi and the pushback. This work is a global approach of an autonomous taxi and pushback system impl...

Turing-Hopf bifurcations in a predator-prey model with herd behavior, quadratic mortality and prey-taxis

Science.gov (United States)

Liu, Xia; Zhang, Tonghua; Meng, Xinzhu; Zhang, Tongqian

2018-04-01

In this paper, we propose a predator-prey model with herd behavior and prey-taxis. Then, we analyze the stability and bifurcation of the positive equilibrium of the model subject to the homogeneous Neumann boundary condition. By using an abstract bifurcation theory and taking prey-tactic sensitivity coefficient as the bifurcation parameter, we obtain a branch of stable nonconstant solutions bifurcating from the positive equilibrium. Our results show that prey-taxis can yield the occurrence of spatial patterns.

Study of the Energy Conversion Process in the Electro-Hydrostatic Drive of a Vehicle

Directory of Open Access Journals (Sweden)

Wiesław Grzesikiewicz

2018-02-01

Full Text Available In the paper, we describe a study of an electro-hydrostatic hybrid drive of a utility van intended for city traffic. In this hybrid drive, the electric drive is periodically accompanied by hydrostatic drive, especially during acceleration and regenerative braking of the vehicle. We present a mathematical model of the hybrid drive as a set of dynamics and regulation equations of the van traveling at a given speed. On this basis, we construct a computer program which we use to simulate the processes of energy conversion in the electro-hydrostatic drive. The main goal of the numerical simulation is to assess the possibility of reducing energy intensity of the electric drive through such a support of the hydrostatic drive. The obtained results indicate that it is possible to reduce the load on elements of the electric system and, therefore, improve energy conversion.

Visual exploration of big spatio-temporal urban data: a study of New York City taxi trips.

Science.gov (United States)

Ferreira, Nivan; Poco, Jorge; Vo, Huy T; Freire, Juliana; Silva, Cláudio T

2013-12-01

As increasing volumes of urban data are captured and become available, new opportunities arise for data-driven analysis that can lead to improvements in the lives of citizens through evidence-based decision making and policies. In this paper, we focus on a particularly important urban data set: taxi trips. Taxis are valuable sensors and information associated with taxi trips can provide unprecedented insight into many different aspects of city life, from economic activity and human behavior to mobility patterns. But analyzing these data presents many challenges. The data are complex, containing geographical and temporal components in addition to multiple variables associated with each trip. Consequently, it is hard to specify exploratory queries and to perform comparative analyses (e.g., compare different regions over time). This problem is compounded due to the size of the data-there are on average 500,000 taxi trips each day in NYC. We propose a new model that allows users to visually query taxi trips. Besides standard analytics queries, the model supports origin-destination queries that enable the study of mobility across the city. We show that this model is able to express a wide range of spatio-temporal queries, and it is also flexible in that not only can queries be composed but also different aggregations and visual representations can be applied, allowing users to explore and compare results. We have built a scalable system that implements this model which supports interactive response times; makes use of an adaptive level-of-detail rendering strategy to generate clutter-free visualization for large results; and shows hidden details to the users in a summary through the use of overlay heat maps. We present a series of case studies motivated by traffic engineers and economists that show how our model and system enable domain experts to perform tasks that were previously unattainable for them.

A Geo-Aware Taxi Carrying Management System by Using Location Based Services and Zone Queuing Techniques on Internet of Things

Directory of Open Access Journals (Sweden)

Chyi-Ren Dow

2016-01-01

Full Text Available Taxi plays a crucial role in the transportation system because of the characteristic that can be hailed conveniently. Most of the taxi drivers obtain passengers by hunting on the road or waiting in a fixed taxi queuing point; however these methods have poor performance, high vacancy rate, and several critical problems such as air pollution and foul up traffic. This study proposed a taxi carrying management system by using location based services and zone queuing techniques on Internet of things. The proposed system allows drivers to both hunt on the road and wait in a queuing zone. A queuing table is used in the control center and neighbor tables are used in RSUs for zone queuing establishment. Joining and leaving mechanisms are developed for zone queuing management. To enhance service efficiency and quality, we present a scheme to prevent the ping-pong effect which is based on the location based services, a hunting rate calculation scheme, and a path planning service for taxi drivers according to the history carrying record. PRISM is used to simulate the proposed system, and the results indicated that our scheme outperforms the waiting and hunting models in terms of number of customers, vacancy rate, and profit.

Video event data recording of a taxi driver used for diagnosis of epilepsy

Directory of Open Access Journals (Sweden)

Kotaro Sakurai

2014-01-01

Full Text Available A video event data recorder (VEDR in a motor vehicle records images before and after a traffic accident. This report describes a taxi driver whose seizures were recorded by VEDR, which was extremely useful for the diagnosis of epilepsy. The patient was a 63-year-old right-handed Japanese male taxi driver. He collided with a streetlight. Two years prior to this incident, he raced an engine for a long time while parked. The VEDR enabled confirmation that the accidents depended on an epileptic seizure and he was diagnosed with symptomatic localization-related epilepsy. The VEDR is useful not only for traffic accident evidence; it might also contribute to a driver's health care and road safety.

Energy Saving Potential in Knuckle Boom Cranes using a Novel Pump Controlled Cylinder Drive

Directory of Open Access Journals (Sweden)

Søren Ketelsen

2018-04-01

Full Text Available This paper is considering the application of a novel pump controlled cylinder drive, the so-called Speed-variable Switched Differential Pump (SvSDP, for knuckle boom crane actuation. Especially the control system for the SvSDP drive is considered, and aiming on improving energy efficiency a refinement of the existing control structure is proposed. An energy efficient sizing algorithm for the SvSDP drive is developed, and fundamental differences between the achievable operating range for the SvSDP drive compared to a conventional valve-cylinder drive are discussed. A case study is conducted with knuckle boom crane actuation, and compared to a conventional valve actuation. Simulation results show that the motion tracking performance is on a similar level compared to the valve actuation approach, while the energy consumption is drastically decreased. For the given test trajectory the valve actuation system consumes 0.79 kWh of electrical energy, while the SvSDP drive consume 0.06 kWh, if ideal energy recovery and storage is assumed.

Health status, job stress and work-related injury among Los Angeles taxi drivers.

Science.gov (United States)

Wang, Pin-Chieh; Delp, Linda

2014-01-01

Taxi drivers work long hours for low wages and report hypertension, weight gain, and musculoskeletal pain associated with the sedentary nature of their job, stressful working conditions, and poor dietary habits. They also experience a high work-related fatality rate. The objective of this study is to examine the association of taxi drivers' health status and level of job stress with work-related injury and determine if a potential interaction exists. A survey of 309 Los Angeles taxi drivers provides basic data on health status, job stress, and work-related injuries. We further analyzed the data using a Modified Poisson regression approach with a robust error variance to estimate the relative risk (RR) and the 95% confidence intervals (CI) of work-related injuries. Focus group results supplemented and helped interpret the quantitative data. The joint effect of good health and low job stress was associated with a large reduction in the incidence of injuries, consistent with the hypothesis that health status and stress levels modify each other on the risk of work-related injury. These results suggest that the combination of stress reduction and health management programs together with changes in the stressful conditions of the job may provide targeted avenues to prevent injuries.

A lightweight neighbor-info-based routing protocol for no-base-station taxi-call system.

Science.gov (United States)

Zhu, Xudong; Wang, Jinhang; Chen, Yunchao

2014-01-01

Since the quick topology change and short connection duration, the VANET has had unstable routing and wireless signal quality. This paper proposes a kind of lightweight routing protocol-LNIB for call system without base station, which is applicable to the urban taxis. LNIB maintains and predicts neighbor information dynamically, thus finding the reliable path between the source and the target. This paper describes the protocol in detail and evaluates the performance of this protocol by simulating under different nodes density and speed. The result of evaluation shows that the performance of LNIB is better than AODV which is a classic protocol in taxi-call scene.

Electron Energy Confinement for HHFW Heating and Current Drive Phasing on NSTX

International Nuclear Information System (INIS)

Hosea, J.C.; Bernabei, S.; Biewer, T.; LeBlanc, B.; Phillips, C.K.; Wilson, J.R.; Stutman, D.; Ryan, P.; Swain, D.W.

2005-01-01

Thomson scattering laser pulses are synchronized relative to modulated HHFW power to permit evaluation of the electron energy confinement time during and following HHFW pulses for both heating and current drive antenna phasing. Profile changes resulting from instabilities require that the total electron stored energy, evaluated by integrating the midplane electron pressure P(sub)e(R) over the magnetic surfaces prescribed by EFIT analysis, be used to derive the electron energy confinement time. Core confinement is reduced during a sawtooth instability but, although the electron energy is distributed outward by the sawtooth, the bulk electron energy confinement time is essentially unaffected. The radial deposition of energy into the electrons is noticeably more peaked for current drive phasing (longer wavelength excitation) relative to that for heating phasing (shorter wavelength excitation) as is expected theoretically. However, the power delivered to the core plasma is reduced consider ably for the current drive phasing, indicating that surface/peripheral damping processes play a more important role for this case

Simulation of Trolleybus Traction Induction Drive With Supercapacitor Energy Storage System

Science.gov (United States)

Brazis, V.; Latkovskis, L.; Grigans, L.

2010-01-01

The article considers the possibilities of saving the regenerative braking energy in Škoda 24Tr type trolleybuses by installing the onboard supercapacitor energy storage system (ESS) and improving its performance with automated switching to the autonomous traction mode. Proposed is an ESS control system with constant DC bus voltage in the supercapacitor charging mode and supercapacitor current proportional to the AC drive current in the discharging mode. The authors investigate stability of the trolleybus ESS control system operating together with AC traction drive in various overhead voltage failure modes. The co-simulation of ESS operation was done by Matlab/Simulink AC drive and PSIM ESS continuous models.

Evaluating the energy efficiency of a one pedal driving algorithm

NARCIS (Netherlands)

Wang, J.; Besselink, I.J.M.; van Boekel, J.J.P.; Nijmeijer, H.

2015-01-01

Regenerative braking of electric vehicles (EVs) is important to improve the energy efficiency and increase the vehicle range. However, the additional friction braking during deceleration may limit the amount of recuperated energy. To improve the energy efficiency and driving comfort of EVs, a one

Stochastic optimal charging of electric-drive vehicles with renewable energy

International Nuclear Information System (INIS)

Pantoš, Miloš

2011-01-01

The paper presents the stochastic optimization algorithm that may eventually be used by electric energy suppliers to coordinate charging of electric-drive vehicles (EDVs) in order to maximize the use of renewable energy in transportation. Due to the stochastic nature of transportation patterns, the Monte Carlo simulation is applied to model uncertainties presented by numerous scenarios. To reduce the problem complexity, the simulated driving patterns are not individually considered in the optimization but clustered into fleets using the GAMS/SCENRED tool. Uncertainties of production of renewable energy sources (RESs) are presented by statistical central moments that are further considered in Hong’s 2-point + 1 estimation method in order to define estimate points considered in the optimization. Case studies illustrate the application of the proposed optimization in achieving maximal exploitation of RESs in transportation by EDVs. -- Highlights: ► Optimization model for EDV charging applying linear programming. ► Formation of EDV fleets based on the driving patterns assessment applying the GAMS/SCENRED. ► Consideration of uncertainties of RES production and energy prices in the market. ► Stochastic optimization. ► Application of Hong’s 2-point + 1 estimation method.

Reducing Energy Demand Using Wheel-Individual Electric Drives to Substitute EPS-Systems

Directory of Open Access Journals (Sweden)

Jürgen Römer

2018-01-01

Full Text Available The energy demand of vehicles is influenced, not only by the drive systems, but also by a number of add-on systems. Electric vehicles must satisfy this energy demand completely from the battery. Hence, the use of power steering systems directly result in a range reduction. The “e2-Lenk” joint project funded by the German Federal Ministry of Education and Research (BMBF involves a novel steering concept for electric vehicles to integrate the function of steering assistance into the drive-train. Specific distribution of driving torque at the steered axle allows the steering wheel torque to be influenced to support the steering force. This provides a potential for complete substitution of conventional power steering systems and reduces the vehicle’s energy demand. This paper shows the potential of wheel-individual drives influencing the driver’s steering torque using a control technique based on classical EPS control plans. Compared to conventional power-assisted steering systems, a reduced energy demand becomes evident over a wide range of operating conditions.

Aircrafts' taxi noise. Sound power level and directivity frequency band results

NARCIS (Netherlands)

Asensio, C.; Pavón, I.; Ruiz, M.; Pagan Munoz, Raul; Recuero, M.

2009-01-01

When noise mapping airports, the main noise sources are take offs and landings. But aircrafts' taxi noise can also be important, and should be considered, for instance when there are residential buildings near the airport's terminal. Main prediction tools, like Integrated Noise Model (INM), do not

Power electronic converter systems for direct drive renewable energy applications

DEFF Research Database (Denmark)

Chen, Zhe

2013-01-01

This chapter presents power electronic conversion systems for wind and marine energy generation applications, in particular, direct drive generator energy conversion systems. Various topologies are presented and system design optimization and reliability are briefly discussed....

Example for electrical energy savings with the pump adjustable electric drive

International Nuclear Information System (INIS)

Mirchevski, Slobodan; Andonov, Zdravko; Saracevic, Fahrudin; Micevski, Darko; Buchkoski, Aleksandar

2004-01-01

Most used method of flow regulation is by throttling the pipeline. Development of power electronic gives opportunity for induction motor pump drives speed control. The common ways of pump flow control are throttling, reducing the working circle, usage of fore circle shovels rotating, by pass and pump speed control Only pump speed control is the most suitable for the energy possibilities. Intensive development of power electronic gives. opportunity to create devices - power converters, which can change the speed of induction motor. For that improvement the energy savings the measurements of power consumption with throttling and speed control have been made. Also, the MATLAB-SIMULINK model of the measured system has been made. The economic effects of saving energy using adjustable speed drives are analyzed for the measured values. The analysis shows that the money payback period of speed controller investment is short compared with the drive lifetime (20 years). (Author)

Electric drives

CERN Document Server

Boldea, Ion

2005-01-01

ENERGY CONVERSION IN ELECTRIC DRIVESElectric Drives: A DefinitionApplication Range of Electric DrivesEnergy Savings Pay Off RapidlyGlobal Energy Savings Through PEC DrivesMotor/Mechanical Load MatchMotion/Time Profile MatchLoad Dynamics and StabilityMultiquadrant OperationPerformance IndexesProblemsELECTRIC MOTORS FOR DRIVESElectric Drives: A Typical ConfigurationElectric Motors for DrivesDC Brush MotorsConventional AC MotorsPower Electronic Converter Dependent MotorsEnergy Conversion in Electric Motors/GeneratorsPOWER ELECTRONIC CONVERTERS (PECs) FOR DRIVESPower Electronic Switches (PESs)The

Harnessing Big-Data for Estimating the Energy Consumption and Driving Range of Electric Vehicles

DEFF Research Database (Denmark)

Fetene, Gebeyehu Manie; Prato, Carlo Giacomo; Kaplan, Sigal

-effects econometrics model used in this paper predicts that the energy saving speed of driving is between 45 and 56 km/h. In addition to the contribution to the literature about energy efficiency of electric vehicles, the findings from this study enlightens consumers to choose appropriate cars that suit their travel......This study analyses the driving range and investigates the factors affecting the energy consumption rate of fully-battery electric vehicles under real-world driving patterns accounting for weather condition, drivers’ characteristics, and road characteristics. Four data sources are used: (i) up...

A new energy-efficient control approach for astronomical telescope drive system

Science.gov (United States)

Zhou, W.; Wang, Y.

2012-12-01

Drive control makes the astronomical telescope accurately tracking celestial bodies in spite of external and internal disturbances, which is a key technique to the performance of telescopes. In this paper, we propose a nonlinear ad, aptive observer based on power reversible approach for high precision telescope position tracking. The nonlinear adaptive observer automatically estimates the disturbances in drive system, and the observed value is applied to compensate for the real disturbances. With greatly reduced disturbances, the control precision can be evidently improved. In conventional drive control, the brake device is often used to slow down the reaction wheel and may waste enormous energy. To avoid those disadvantages, an H-bridge is put forward for wheel speed regulation. Such H-bridge has four independent sections, and each section mainly consists of a power electronic switch and an anti-parallel diode. During the period of the mount slowing down, the armature current of drive motor goes through the two path-wise diodes to charge the battery. Thus, energy waste is avoided. Based on the disturbance compensation, an optimal controller is designed to minimize an evaluation function which is made up of a weighted sum of position errors and energy consumption.The outputs of the controller are applied to control the H-bridge. Simulations are performed in MATLAB language. The results show that high precision control can be obtained by the proposed approach. And the energy consumption will be remarkably reduced.

PERFORMANCE AND DURABILITY OF THE PSA PEUGEOT CITROEN'S DPF SYSTEM ON A TAXI FLEET IN THE PARIS AREA

Energy Technology Data Exchange (ETDEWEB)

COROLLER, P; PLASSAT, G

2003-08-24

The use of Diesel engines has strongly increased during the last years and now represents 40% of the sales in Europe and up to 50% of the number of cars in circulation for some countries. This success is linked not only to the economical aspect of the use of such vehicles, but also to the recent technological improvements of these engines. The new technical solutions (high pressure direct injection, turbocharger) have indeed allowed the increase of these engine performances while decreasing their fuel consumption, pollutant emissions and noise level. From an environment point of view, Diesel engines are nevertheless penalized by their particulates and NOx emissions. The study and the treatment of the particulate, highly criticized for their potential impact on health, are the subject of numerous works of characterizations and developments. PSA Peugeot Citroen has recently (2000) launched its particulate filter technology on several types of vehicles (500,000 vehicles with DPF have been sold today). In order to evaluate the durability of this technology over a long period of time, a study program has been set-up by ADEME (French Environmental Agency), IFP Powertrain, PSA Peugeot Citroen and Taxis G7 (a Parisian taxis Company). The objective is to study the evolution of five taxis and their after-treatment system performances over 80,000km mileage--which corresponds to the recommended mileage before the first DPF maintenance--in hard urban driving conditions, as well over 120,000km, after the DPF maintenance and remanufacturing. More specifically, the following evaluations are being performed at regular intervals (around 20,000km): regulated gaseous pollutant emissions on NEDC cycle, particulate emissions and unregulated pollutant emissions. The results obtained until now have not shown any degradation of the particulate filter efficiency (more than 90%). This paper presents the methodology set-up, and the explanation of the first results obtained. Indeed, a more

41 CFR 301-10.421 - How much will my agency reimburse me for a tip to a taxi, shuttle service, or courtesy...

Science.gov (United States)

2010-07-01

... reimburse me for a tip to a taxi, shuttle service, or courtesy transportation driver? 301-10.421 Section 301..., Shuttle Services, Or Other Courtesy Transportation § 301-10.421 How much will my agency reimburse me for a tip to a taxi, shuttle service, or courtesy transportation driver? An amount which your agency...

Energy efficiency high speed drives with magnetic bearings; Energieeffizienz durch schnell drehende, magnetgelagerte Antriebe

Energy Technology Data Exchange (ETDEWEB)

Kroll, Matthias [LEViTEC GmbH, Lahnau (Germany)

2011-07-01

In modern purification plans the contamination of the wastewater are biologically removed by supplying oxygen. The clarifier is ventilated by compressors around the clock and approximately 60% of the total energy consumption is used for that. It enables a great opportunity for saving energy. This contribution shows that the use of magnetic centrifugal compressors with high-speed drives leads to significant reduction of energy consumption. In addition, the drive is, due to contact free the magnetic bearings, practically wear- and maintenance-free. By the use of integrated sensors in the magnetic bearings a continuous monitoring of the compressor is implemented. Consequently this drive concept provides not only more efficiency and less energy consumption, but also leads to a higher plant availability. (orig.)

Development of a micro-hybrid system for a three-wheeled motor taxi

NARCIS (Netherlands)

Hofman, T.; Tas, van der S.G.; Ooms, W.; Van Meijl, E. W P; Laugeman, B. M.

2009-01-01

In large cities in Asia and Africa millions of auto-rickshaws offer their taxi-services. At the same time these three-wheelers cause severe air-pollution and produce large amounts of green house gasses (carbon dioxide). The goal of the research presented in this paper is to develop a compact, robust

Relation between workplace accidents and the levels of carboxyhemoglobin in motorcycle taxi drivers.

Science.gov (United States)

da Silva, Luiz Almeida; Robazzi, Maria Lúcia do Carmo Cruz; Terra, Fábio de Souza

2013-01-01

To investigate the relation between workplace accidents and the levels of carboxyhemoglobin found in motorcycle taxi drivers. Correlational, quantitative study involving 111 workers and data obtained in July 2012 through a questionnaire to characterize the participants and blood collection to measure carboxyhemoglobin levels. 28.8% had suffered workplace accidents; 27.6% had fractured the lower limbs and significant symptoms of carbon monoxide exposure were verified in smokers. The carboxyhemoglobin levels were higher among smokers and victims of workplace accidents. Motorcycle taxi drivers had increased levels of carboxyhemoglobin, possibly due to the exposure to carbon monoxide; these levels are also increased among smokers and victims of workplace accidents. The study provides advances in the knowledge about occupational health and environmental science, and also shows that carboxyhemoglobin can be an indicator of exposure to environmental pollutants for those working outdoors, which can be related to workplace accidents.

Pattern of seat belt use and its associated factors among taxi drivers ...

African Journals Online (AJOL)

Objective: Road traffic injuries constitute a major public health concern that demands effective interventions. Use of car seat belts is recommended as an effective intervention to reduce serious and fatal road traffic injuries. The study intended to investigate the pattern of seat belt use and its correlates among taxi drivers in ...

THE CALCULATION OF THE ENERGY RECOVERY ELECTRIFIED URBAN TRANSPORT DURING THE INSTALLATION DRIVE FOR TRACTION SUBSTATION

Directory of Open Access Journals (Sweden)

A. A. Sulim

2014-01-01

Full Text Available At present a great attention is paid to increasing of energy efficiency at operated electrified urban transport. Perspective direction for increasing energy efficiency at that type of transport is the application of regenerative braking. For additional increasing of energy efficiency there were suggested the use of capacitive drive on tires of traction substation. One of the main task is the analysis of energy recovery application  with drive and without it.These analysis demonstrated that the calculation algorithms don’t allow in the full volume to carry out calculations of amount and cost of energy recovery without drive and with it. That is why we see the current interest to this topic. The purpose of work is to create methods of algorithms calculation for definite amount and cost of consumed, redundant and recovery energy of electrified urban transport due to definite regime of motion on wayside. There is algorithm developed, which allow to calculate amount and cost of consumed, redundant and recovery energy of electrified urban transport on wayside during the installation capacitive drive at traction substation. On the basis of developed algorithm for the definite regime of wagon motion of subway there were fulfilled the example of energy recovery amount and its cost calculation, among them with limited energy intensity drive, when there are 4 trains on wayside simultaneously.

A new energy-efficient control approach for space telescope drive system

Science.gov (United States)

Zhou, Wangping; Wang, Yong

Drive control makes the telescope accurately track celestial bodies in spite of external and in-ternal disturbances, and is a key technique to the performance of telescopes. In this paper, we propose a nonlinear adaptive observer based on power reversible approach for high preci-sion position tracking, i.e., space telescopes. The nonlinear adaptive observer automatically estimates the disturbances in drive system, and the observed value is applied to compensate for the real disturbances. With greatly reduced disturbances, the control precision can be ev-idently improved. In conventional drive control, the brake device is often used to slow down the reaction wheel and may waste enormous energy. To avoid those disadvantages, an H-bridge is put forward for wheel speed regulation. Such H-bridge has four independent sections, and each section mainly consists of a power electronic switch and an anti-parallel diode. A pair of diagonal sections is switched on for speeding up the reaction wheel and the other pair act in reverse. During the period of the wheel slowing down, the armature current of drive motor goes through the two path-wise diodes to discharge the battery. Thusly, energy waste is avoided. Based on the disturbance compensation, an optimal controller is designed to minimize an eval-uation function which is made up of a weighted sum of position errors and energy consumption. The outputs of the controller are amplified to control the H-bridge. Simulations are performed in MATLAB language. The results show that high precision control can be obtained by the proposed approach. And the energy consumption will be remarkably reduced.

A Comparative Study of Back Pain among Taxi and Truck Drivers in ...

African Journals Online (AJOL)

Data was analyzed using SSPSS version 20. Descriptive and analytical statistics to analyze and present data. The prevalence of back pain in Port Harcourt for taxi drivers was 70.4% and 71.4% for truck drivers. The prevalence among truck drivers was due to age ,sitting position and shock absorbers. However variables like ...

Relation between workplace accidents and the levels of carboxyhemoglobin in motorcycle taxi drivers

Directory of Open Access Journals (Sweden)

Luiz Almeida da Silva

2013-09-01

Full Text Available OBJECTIVE: to investigate the relation between workplace accidents and the levels of carboxyhemoglobin found in motorcycle taxi drivers. METHOD: correlational, quantitative study involving 111 workers and data obtained in July 2012 through a questionnaire to characterize the participants and blood collection to measure carboxyhemoglobin levels. RESULT: 28.8% had suffered workplace accidents; 27.6% had fractured the lower limbs and significant symptoms of carbon monoxide exposure were verified in smokers. The carboxyhemoglobin levels were higher among smokers and victims of workplace accidents. CONCLUSION: motorcycle taxi drivers had increased levels of carboxyhemoglobin, possibly due to the exposure to carbon monoxide; these levels are also increased among smokers and victims of workplace accidents. The study provides advances in the knowledge about occupational health and environmental science, and also shows that carboxyhemoglobin can be an indicator of exposure to environmental pollutants for those working outdoors, which can be related to workplace accidents.

The liver taxis of receptor mediated lactosaminated human growth hormone

International Nuclear Information System (INIS)

Chen Zelian; Shi Lin; Li Tongling; Pang Qijie; He Juying; Guan Changtian

2002-01-01

Radiography imaging is used to assess liver taxis mechanism of anti-dwarfism drug lactosaminated human growth hormone (L-rhGH). Both L-rhGH and rhGH labelled with 131 I are used to study their biodistribution in animals (including rabbits, cocks and rats). The results show that L-rhGH is of specific hepatic targeting property, and the maximum hepatic concentration rate is 76.8%, which is two times of rhGH. Its hepatic binding is receptor mediated

The use of driving simulators for enhancing train driver’s performance in terms of energy consumption

Energy Technology Data Exchange (ETDEWEB)

Salvador Zuriaga, P.; Garcia Roman, C.; Pineda Jaramillo, J.D.; Insa Franco, R.

2016-07-01

This paper presents a driving simulator to be used by train drivers for training their driving skills in terms of energy-efficiency. In railway operations, previous experiences have shown differences in energy consumption up to 20 % among train drivers for the same journey in similar operational conditions. This shows great saving potentials in both economic and environmental terms. For this reason, railway companies wishing to become more efficient must encourage their train drivers to balance the energy consumption towards the minimum threshold. In this sense, driving simulators are a good complement for training courses on energy-saving best practices given to train drivers, where they can put into practice the learned contents. The developed driving simulator consists in an Excel spreadsheet including an accurate energy consumption model, which was previously developed from real measurements on different train services. The fact of being an Excel spreadsheet provides a familiar interface to train drivers, making easier its use, and becomes an affordable tool for small and medium size freight private railway companies. Furthermore, the fact of being a non-real-time simulation makes possible to perform a journey of several hours in a few minutes, thus being able to test different driving strategies for the same train journey in a short time period. In this paper, the driving simulator was applied to the Valencia-Cuenca-Aranjuez railway line operated by Renfe Operadora with Diesel Multiple Units. The results are given in terms of fuel consumption, costs of fuel and CO2 emissions and enable train drivers to find by themselves the most efficient way to drive the train between two stations. Finally, this driving simulator may serve as the basis for training and evaluating train drivers in order to set up a bonus/penalty policy for rewarding the most efficient train drivers and achieve an overall energy consumption reduction. (Author)

REDUCING ENERGY CONSUMPTION BY PASSENGER CAR WITH USING OF NON-ELECTRICAL HYBRID DRIVE TECHNOLOGY

Directory of Open Access Journals (Sweden)

Tomas Skrucany

2017-03-01

Full Text Available Not only electrical hybrid technology is used for drivetrain of passenger cars. Also other systems using non-electrical principles (hydraulic or air pressure, mechanical energy storage can be found in current vehicles. There is a quantification of the spared energy by using a hybrid vehicle in the paper. Driving cy-cle ECE 15 was chosen as a platform for simulation of driving resistances.

Energy efficiency improvements in electric motors and drives

Energy Technology Data Exchange (ETDEWEB)

Bertoldi, P. [Commission of the European Communities, Brussels (Belgium). Directorate General for Energy; Ameida, A.T. de [Coimbra Univ. (Portugal). Dept. de Engenharia Electrotecnica; Falkner, H. [eds.] [AEA Technolgy, Harwell (United Kingdom). ETSU

2000-07-01

This book covers the state of the art of energy-efficient electric motor technologies, which can be used now and in the near future to achieve significant and cost-effective energy savings. Recent developments in advanced motor technologies by some of the largest manufacturers of motors and drives are also presented. Although energy-efficient motor technologies can save a huge amount of electricity, they still have not been widely adopted. The barriers which can hinder the adoption of those technologies are presented. Policies and programmes to promote the large scale penetration of energy-efficient technologies and the market transformation are featured in the book, describing the experiences carried out in different parts of the world. This extensive coverage includes contributions from relevant institutions in the European Union, North America, Latin America, Japan, Australia and New Zealand. (orig.)

Energy Management Strategy Based on the Driving Cycle Model for Plugin Hybrid Electric Vehicles

Directory of Open Access Journals (Sweden)

Xiaoling Fu

2014-01-01

Full Text Available The energy management strategy (EMS for a plugin hybrid electric vehicle (PHEV is proposed based on the driving cycle model and dynamic programming (DP algorithm. A driving cycle model is constructed by collecting and processing the driving data of a certain school bus. The state of charge (SOC profile can be obtained by the DP algorithm for the whole driving cycle. In order to optimize the energy management strategy in the hybrid power system, the optimal motor torque control sequence can be calculated using the DP algorithm for the segments between the traffic intersections. Compared with the traditional charge depleting-charge sustaining (CDCS strategy, the test results on the ADVISOR platform show a significant improvement in fuel consumption using the EMS proposed in this paper.

Taking actions to quit chewing betel nuts and starting a new life: taxi drivers' successful experiences of quitting betel nut chewing.

Science.gov (United States)

Yang, Tsui-Yun; Lin, Hung-Ru

2017-04-01

To understand taxi drivers' successful experiences of quitting betel nut chewing. Previous studies verified that betel nut chewing significantly increases the risk of oral cancer. In Taiwan, taxi drivers work for approximately 10-13 hours per day, and 31·7-80% of them choose to chew betel nuts for their invigorating qualities, which enable them to work more hours and receive more income. A qualitative research design was used. This study used the grounded theory method with purposive sampling to perform in-depth interviews with male taxi drivers who had successfully quit betel nut chewing for more than six months. The interviewed participants were 25 taxi drivers aged 45-67 who had chewed betel nuts for an average of 30·9 years. A constant comparative analysis of the 25 interviews revealed six categories, namely the first experience of chewing betel nuts, a part of work and life, perceiving the impact of betel nuts, trying to change, acting to quit betel nut chewing and starting a new life. During the cessation process, taxi drivers tended to be affected by their addiction to chewing betel nuts and the temptation of friends' invitations to chew betel nuts. However, their recognition of the physical effects of betel nut chewing and their sense of responsibility and commitment to family were the critical factors affecting their determination to quit betel nut chewing. Their willpower to not to chew betel nuts and the source of their motivation to exercise self-control also contributed to their success. Healthcare personnel should understand the experiences and perceptions of betel nut chewers, strengthen their understanding of the effects of betel nut chewing on physical health during the cessation period and support their self-efficacy and quitting behaviours with the assistance of significant others. © 2016 John Wiley & Sons Ltd.

A Feasibility Test on Adopting Electric Vehicles to Serve as Taxis in Daejeon Metropolitan City of South Korea

Directory of Open Access Journals (Sweden)

Seoin Baek

2016-09-01

Full Text Available For realizing sustainable development, EV (Electric Vehicle is currently considered as one of the most promising alternative due to its cleanness and inexhaustibility. However, the development and dissemination of EV has stagnated because it faces major constraints such as battery performance and an excessively long charging time. Thus, this study examined the feasibility of using EVs as taxis by analyzing real data from a pilot project in Daejeon, a metropolitan city in South Korea for proposing the effective way to adopt EV. To reflect reality and improve accuracy, we adopted scenarios and assumptions based on in-depth interviews with groups of experts. The resulting initial benefit-to-cost (B/C ratio for EV taxis is approximately 0.4, which is quite low compared to 0.7 for traditional taxis. However, after incorporating some further assumptions into the calculation, the B/C ratio shifts to approximately 0.7, which is more appropriate for EV adoption. For this improvement to be achieved, the dissemination of a charging infrastructure, improvement of the business model and policy support is strongly needed. Limitations to this work and potential areas for future study are also fully discussed.

Kinetics and substrate selectivity of a Triticum aestivum xylanase inhibitor (TAXI) resistant D11F/R122D variant of Bacillus subtilis XynA xylanase

DEFF Research Database (Denmark)

Rasmussen, Louise Enggaard; Sørensen, Jens F.; Meyer, Anne S.

2010-01-01

This study examined the kinetics and substrate selectivity of a GH11 Bacillus subtilis XynA xylanase (BsX) sensitive to inhibition by TAXI and an engineered variant, which is much less inhibited by TAXI (BsX(mut)). The main purpose of the work was to elucidate any influence of the structural point...

Operations of electric taxis to serve advance reservations by trip chaining: Sensitivity analysis on network size, customer demand and number of charging stations

Directory of Open Access Journals (Sweden)

Hao Wang

2016-10-01

Full Text Available This research investigated the performance of an Electric Taxi (ET fleet that catered solely for customers with advance reservations. In a previously related research, a customized Paired Pickup and Delivery Problem with Time Window and Charging Station (PPDPTWCS had been formulated to solve for the minimum number of taxis that would serve a fixed set of customer demand. The concept behind this fleet optimization was to chain multiple customer trips and trips to Charging Stations (CSs to form a route and assigned to a taxi driver. In this paper the sensitivity of the ET fleet’s operations with respect to network sizes, customer demand densities and number of CSs have been investigated. It also analyzed the market shares of the CSs and the occupancy of a CS over time. The results showed that, (1 the expansion of network size or the increase in customer demand density led to increase in fleet size, number of trips to the CSs and maximum occupancies at the CSs but these performance measures grew at different rates; (2 when the network size and number of CSs were fixed, an increase in customer demand density led to a better utilization of taxis in terms of more customers served per taxi and higher average revenue per taxi; (3 given the same network size and demand density, the ET fleet’s performance was relatively insensitive to the number of CSs; and (4 the usage of individual CS was affected by the number of CS and their locations; and (5 when all the ETs were fully charged at the beginning of the same shift hour, they visited the CSs in bunches when their batteries were about to run out. These findings contribute to a better understanding of the operations of the ET fleet and the CSs. They could be used for making better decisions in the planning of ET operations.

PENINGKATAN HASIL BELAJAR PERPAJAKAN MELALUI MEDIA TAXI SNADERS PADA SISWA XI B SMK PL TARCISIUS 2

Directory of Open Access Journals (Sweden)

Cornelius Hery Setyawan

2016-01-01

Full Text Available Vocational School (SMK is an educational institution to transfer knowledge about the tax. Unluckily, teaching learning process in delivering this material was monotonous, so it needed a medium called TAXI SNADERS. The objective of the study was to increase interest and learning outcomes taxation on Value Added Tax (VAT and Sales of Luxury through a medium called TAXI SNADERS. The result of the study showed that there was improvement toward students’ interest for 14.5%. On the 1st cycle, students’ interest was only 67.25%, then it increased up to 81.75% on the 2nd cycle. Moreover, students’ learning outcomes also increased for 20% in post test. It was 67% on the 1st cycle and rose to 87% on the 2nd cycle. 

The combination of short rest and energy drink consumption as fatigue countermeasures during a prolonged drive of professional truck drivers.

Science.gov (United States)

Ronen, Adi; Oron-Gilad, Tal; Gershon, Pnina

2014-06-01

One of the major concerns for professional drivers is fatigue. Many studies evaluated specific fatigue countermeasures, in many cases comparing the efficiency of each method separately. The present study evaluated the effectiveness of rest areas combined with consumption of energy drinks on professional truck drivers during a prolonged simulated drive. Fifteen professional truck drivers participated in three experimental sessions: control-drivers were asked to drink 500 ml of a placebo drink prior to the beginning of the drive. Energy drink-drivers were asked to drink 500 ml of an energy drink containing 160 mg of caffeine prior to the beginning of the drive, and an Energy drink+Rest session--where the drivers were asked to drink 500 ml of an energy drink prior to driving, and rest for 10 min at a designated rest area zone 100 min into the drive. For all sessions, driving duration was approximately 150 min and consisted of driving on a monotonous, two-way rural road. In addition to driving performance measures, subjective measures, and heart rate variability were obtained. Results indicated that consumption of an energy drink (in both sessions) facilitated lower lane position deviations and reduced steering wheel deviations during the first 80-100 min of the drive relative to the control sessions. Resting after 100 min of driving, in addition to the energy drink that was consumed before the drive, enabled the drivers to maintain these abilities throughout the remainder of the driving session. Practical applications: Practical applications arising from the results of this research may give indication on the possible added value of combining fatigue counter measures methods during a prolonged drive and the importance of the timing of the use for each method. Copyright © 2014 Elsevier Ltd. All rights reserved.

Driving forces and barriers to improved energy performance of buildings: an analysis of energy performance of Swedish buildings, 2000-2006

Energy Technology Data Exchange (ETDEWEB)

Fuglseth, Bente Beckstroem

2008-06-15

The building sector is responsible for a substantial part of energy use and green house gas emissions in Europe. This report explores driving forces and barriers to improved energy performance of buildings, using the Swedish building sector as a case. The development of energy performance of buildings in Sweden from 2000 until 2006 is explored by applying a threefold understanding of energy performance of buildings: substitution from fossil fuels to renewable energy, conversion from electrical heating to thermal energy and reduction in energy demand. Three explanatory approaches are used to analyse driving forces and barriers to improved energy performance: the techno-economic approach stresses the physical aspects of infrastructure and technologies, the institutional approach emphasizes the role of institutional factors, while the regulative approach focuses on formal rules and laws. The study concludes that all factors have promoted substitution of fossil fuels with renewable energy, while they have prevented conversion from electrical heating to thermal energy and reduction in energy demand. (author). 95 refs

Energy researchers - 1. Energy efficiency: Energy efficiency is driving innovation; No economic crisis for energy efficiency; How can we change our energy habits?

International Nuclear Information System (INIS)

Minster, Jean-Francois; Appert, Olivier; Moisan, Francois; Salha, Bernard; Tardieu, Bernard; Ghidaglia, Jean-Michel; Viterbo, Jerome

2011-01-01

A first article comments how the race to achieve energy efficiency is driving the emergence of new technologies in transportation and construction (hybrid cars, phase change material, digital mock-ups, and so on). The example of the AGV is evoked, a new version of the TGV developed by Alstom which will run faster and consume less energy. A second article outlines that, due to the support from public authorities and to an increased awareness of energy costs and environmental challenges, the energy savings market is booming. Then, in an interview, a sociologist of the ADEME comments the difficulty of changing habits in terms of energy savings

Energy Management Strategy for Hybrid Electric Vehicle Based on Driving Condition Identification Using KGA-Means

Directory of Open Access Journals (Sweden)

Shuxian Li

2018-06-01

Full Text Available In order to solve the problem related to adaptive energy management strategies based on driving condition identification being difficult to be applied to a real hybrid electric vehicle (HEV controller, this paper proposes an energy management strategy by combining the driving condition identification algorithm based on genetic optimized K-means clustering algorithm (KGA-means, and the equivalent consumption minimization strategy (ECMS. The simulation results show that compared with ECMS, the energy management strategy proposed in this article drives the engine working point closer to the best efficiency curve, and smooths out the state of charge (SOC change and better maintains the SOC in a highly efficient area. As a result, the vehicle fuel consumption reduces by 6.84%.

Road transport-related energy consumption: Analysis of driving factors in Tunisia

International Nuclear Information System (INIS)

Mraihi, Rafaa; Abdallah, Khaled ben; Abid, Mehdi

2013-01-01

The rapid growth of urban population and the development of road infrastructures in Tunisian cities have brought about many environmental and economic problems, including the rise scored in energy consumption and the increase in the quantity of gas emissions arising from road transport. Despite the critical nature of such problems, no policies have yet been adopted to improve energy efficiency in the transport sector. This paper aims to determine driving factors of energy consumption change for the road mode. It uses decomposition analysis to discuss the effects of economic, demographic and urban factors on the evolution of transport energy consumption. The main result highlighted in the present work is that vehicle fuel intensity, vehicle intensity, GDP per capita, urbanized kilometers and national road network are found to be the main drivers of energy consumption change in the road transport sector during 1990–2006 period. Consequently, several strategies can be elaborated to reduce road transport energy. Economic, fiscal and regulatory instruments can be applied in order to make road transport more sustainable. -- Highlights: •We are interested in determining driving factors of transport energy consumption growth in Tunisia. •We use decomposition analysis approach. •Vehicle fuel and road vehicle intensities are found to be principal factors. •Motorization and urbanization are also found to be responsible

TrajGraph: A Graph-Based Visual Analytics Approach to Studying Urban Network Centralities Using Taxi Trajectory Data.

Science.gov (United States)

Huang, Xiaoke; Zhao, Ye; Yang, Jing; Zhang, Chong; Ma, Chao; Ye, Xinyue

2016-01-01

We propose TrajGraph, a new visual analytics method, for studying urban mobility patterns by integrating graph modeling and visual analysis with taxi trajectory data. A special graph is created to store and manifest real traffic information recorded by taxi trajectories over city streets. It conveys urban transportation dynamics which can be discovered by applying graph analysis algorithms. To support interactive, multiscale visual analytics, a graph partitioning algorithm is applied to create region-level graphs which have smaller size than the original street-level graph. Graph centralities, including Pagerank and betweenness, are computed to characterize the time-varying importance of different urban regions. The centralities are visualized by three coordinated views including a node-link graph view, a map view and a temporal information view. Users can interactively examine the importance of streets to discover and assess city traffic patterns. We have implemented a fully working prototype of this approach and evaluated it using massive taxi trajectories of Shenzhen, China. TrajGraph's capability in revealing the importance of city streets was evaluated by comparing the calculated centralities with the subjective evaluations from a group of drivers in Shenzhen. Feedback from a domain expert was collected. The effectiveness of the visual interface was evaluated through a formal user study. We also present several examples and a case study to demonstrate the usefulness of TrajGraph in urban transportation analysis.

Digital collaborative consumption and social issues: The clash of taxi and Uber driver in Surabaya and Taipei

Directory of Open Access Journals (Sweden)

Kholifatus Saadah

2017-12-01

Full Text Available Since the occurrence of application-based taxi, phenomenon and resistance have emerged in metropolitan cities around the world. One of the main issues highlighted is digital collaborative consumption which emerges as the consequences of globalization. As an interpretive case study research, this paper aims to analyze the use of Uber as an alternative to public transportation in Taipei and Surabaya. Authors discuss the issue by comparing the reaction toward the occurrence of Uber and Taipei and Surabaya. Authors apply the theory from Hegre, Gissinger, & Gledtisch (2002 about globalization and social conflict to explain social issues as the consequences of digital collaborative consumption as the new consumption model. According to the theory, globalization creates a deprivation which makes the struggle to access source of capital become more intense. Poverty is the main generator of radical action and violence. Analyzing the phenomena of Uber usage and the resistance from traditional taxi businessmen in Taipei and Surabaya, the authors argue that globalization reflected on digital collaborative consumption could lead to social unrest for parties who cannot adapt to the changes in economic practice. As shown by many cases of app-based rejection taxi in public places such as airport, train station and bus station; the traditionalists show resistance towards globalization and the economic shift of public transportation business model.

Aspergillus prevalence in air conditioning filters from vehicles: taxis for patient transportation, forklifts, and personal vehicles.

Science.gov (United States)

Viegas, Carla; Moreira, Ricardo; Faria, Tiago; Caetano, Liliana Aranha; Carolino, Elisabete; Gomes, Anita Quintal; Viegas, Susana

2018-05-04

The frequency and importance of Aspergillus infections is increasing worldwide. This study aimed to assess the occupational exposure of forklifts and taxi drivers to Aspergillus spp. Nineteen filters from air conditioning system of taxis, 17 from forklifts and 37 from personal vehicles were assessed. Filters extract were streaked onto MEA, DG18 and in azole-supplemented media. Real-time quantitative PCR amplification of selected Aspergillus species-complex was also performed. Forklifts filter samples presented higher median values. Aspergillus section Nigri was the most observed in forklifts filters in MEA (28.2%) and in azole-supplemented media. DNA from Aspergillus sections Fumigati and Versicolores was successfully amplified by qPCR. This study enlightens the added value of using filters from the air conditioning system to assess Aspergillus spp. occupational exposure. Aspergillus azole resistance screening should be included in future occupational exposure assessments.

Negotiating EU CO2/energy taxation. Political economic driving forces and barriers

International Nuclear Information System (INIS)

Klok, Jacob

2001-11-01

The primary objective of this project is to identify the main political economic driving forces behind and barriers against the creation of an EU agreement on CO 2 /energy taxation. The analysis is based on a theoretical framework for understanding European integration and on detailed historical investigations into a process of EU negotiations concerning CO 2 /energy taxation that took place from the 1980s to 1994. Following the historical analysis of political economic driving forces and barriers, some overall perspectives on possible future developments within the field of EU CO 2 /energy taxation are finally advanced. The secondary objective of the project is to consider the possible effects on the EU negotiation process of Danish efforts to push the CO 2 /energy tax proposal from the late 1980s to 994. This analysis is based on the preceding historical analysis of the EU negotiation process, as well as further investigations into the national Danish development within the field of CO 2 /energy taxation, including accounts of Denmark's particular relations with the EU during the period in question. Finally, based on the likely future developments in the field EU CO 2 /energy taxation. Denmark's strategic opportunities are outlined. (BA)

Development of a driving cycle to evaluate the energy economy of electric vehicles in urban areas

International Nuclear Information System (INIS)

Brady, John; O’Mahony, Margaret

2016-01-01

Highlights: • Development of a driving cycle to evaluate energy economy of electric vehicles. • Improves on existing driving cycles by using real world data from electric vehicles. • Driving data from different road types and traffic conditions included. - Abstract: Understanding real-world driving conditions in the form of driving cycles is instrumental in the design of efficient powertrains and energy storage systems for electric vehicles. In addition, driving cycles serve as a standardised measurement procedure for the certification of a vehicle’s fuel economy and driving range. They also facilitate the evaluation of the economic and lifecycle costs of emerging vehicular technologies. However, discrepancies between existing driving cycles and real-world driving conditions exist due to a number of factors such as insufficient data, inadequate driving cycle development methodologies and methods to assess the representativeness of developed driving cycles. The novel aspect of the work presented here is the use of real-world data from electric vehicles, over a six month period, to derive a driving cycle appropriate for their assessment. A stochastic and statistical methodology is used to develop and assess the representativeness of the driving cycle against a separate set of real world electric vehicle driving data and the developed cycle performs well in that comparison. Although direct comparisons with internal combustion engine driving cycles are not that informative or relevant due to the marked differences between how they and electric vehicles operate, some discussion around how the developed electric vehicle cycle relates to them is also included.

Mining Open Datasets for Transparency in Taxi Transport in Metropolitan Environments

OpenAIRE

Noulas, Anastasios; Salnikov, Vsevolod; Lambiotte, Renaud; Mascolo, Cecilia

2015-01-01

Uber has recently been introducing novel practices in urban taxi transport. Journey prices can change dynamically in almost real time and also vary geographically from one area to another in a city, a strategy known as surge pricing. In this paper, we explore the power of the new generation of open datasets towards understanding the impact of the new disruption technologies that emerge in the area of public transport. With our primary goal being a more transparent economic landscape for urban...

Development of a Trip Energy Estimation Model Using Real-World Global Positioning System Driving Data: Preprint

Energy Technology Data Exchange (ETDEWEB)

Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhu, Lei [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Tian, Ye [Metropia, Inc.

2017-09-15

A data-driven technique for estimation of energy requirements for a proposed vehicle trip has been developed. Based on over 700,000 miles of driving data, the technique has been applied to generate a model that estimates trip energy requirements. The model uses a novel binning approach to categorize driving by road type, traffic conditions, and driving profile. The trip-level energy estimations can easily be aggregated to any higher-level transportation system network desired. The model has been tested and validated on the Austin, Texas, data set used to build this model. Ground-truth energy consumption for the data set was obtained from Future Automotive Systems Technology Simulator (FASTSim) vehicle simulation results. The energy estimation model has demonstrated 12.1 percent normalized total absolute error. The energy estimation from the model can be used to inform control strategies in routing tools, such as change in departure time, alternate routing, and alternate destinations, to reduce energy consumption. The model can also be used to determine more accurate energy consumption of regional or national transportation networks if trip origin and destinations are known. Additionally, this method allows the estimation tool to be tuned to a specific driver or vehicle type.

Field dispersal ability and taxis to sex pheromone of irradiated F-1 male Asian corn borer

International Nuclear Information System (INIS)

Wang Huasong; Liu Qiongru; Lu Daguang; Wang Endong; Kang Wen; Li Yongjun; He Qiulan; Hu Jianguo

1998-01-01

The dispersal ability of F-1 male Asian corn borer, Ostrinia furnacalis (Guenee), irradiated with 100, 150 and 200 Gy Separately in parental generation were tested by marking (with Calco oil red or Sudan blue internally)-releasing-recapturing (with synthesized sex pheromone) method in the field where the farthest distance from release point to pheromone trap was 550 m. The results showed that, as compared with the normal male moths, despite of the fact that a part of the irradiated F-1 males had lost dispersal ability or taxis to sex pheromone, there was no significant difference between the captured rates of irradiated F-1 males and normal males in the trap 550 m from release point, indicated that the dispersal ability or taxis to sex pheromone of irradiated F-1 males arrived at 550 m from release point are still well matched with the normal ones

Optimal Fare, Vacancy Rate, and Subsidies under Log-Linear Demand with the Consideration of Externalities for a Cruising Taxi Market

Directory of Open Access Journals (Sweden)

Chun-Hsiao Chu

2017-01-01

Full Text Available Externality is an important issue for formulating the regulation policy of a taxi market. However, this issue is rarely taken into account in the current policy-making process, and it has not been adequately explored in prior research. This study extends the model proposed by Chang and Chu in 2009 with the aim of exploring the effect of externality on the optimization of the regulation policy of a cruising taxi market. A closed-form solution for optimizing the fare, vacancy rate, and subsidy of the market is derived. The results show that when the externality of taxi trips is taken into consideration, the optimal vacancy rate should be lower and the subsidy should be higher than they are under current conditions where externality is not considered. The results of the sensitivity analysis on the occupied and vacant distance indicate that the relation of the vacant distance to the marginal external cost is more sensitive than the occupied distance. The result of the sensitivity analysis on the subsidy shows the existence of a negative relationship between the marginal external cost and the optimal subsidy.

The Correlation between Duration of Employment, Body Posture and Smoking Habit on Low Back Pain Incidence An Analytic Observational Study Among Taxi Driver in Semarang Municipality

Directory of Open Access Journals (Sweden)

Syifa Dian Firmanita

2015-06-01

Full Text Available Introduction: Low back pain ((LBP ranks as number two of neurological disease’s highest prevalence after cephalgia and migraine in Indonesia. Objective: This study aim to determine the relationship between duration of employment, body posture and smoking habit on the incidence of low back pain on taxi driver. Method: This research is an observational analytic cross sectional design. Seventyfour taxi drivers in Semarang municipality was screened with Beck’s Depression Inventory Scale to meet the inclusion and exclusion criteria. Respondents were then given Risk Factor of LBP questionnaire. Data were analyzed with a bivariate correlation test contingency coefficient to see the relationship between duration of employment, body posture, smoking habit and low back pain.Result: the taxi driver with duration of employment >10 years were moderate smokers and having astenis body posture. The analysis of correlation coefficients contingency test showed a significance relationship between duration of employment (p = 0,000, body posture (p = 0,000, and moderate smokers (p=0.010 with the incidence of LBP. Conclusion: the taxi driver with duration of employment >10 years with astenis body posture, and moderate smokers were posstively correlated with LBP.

Research on the Multi-Energy Management Strategy of the Electric Drive System of a Tracked Bulldozer

Directory of Open Access Journals (Sweden)

Ming Pan

2016-01-01

Full Text Available The multi-energy management strategy of electric drive system of tracked bulldozer was researched. Firstly, based on power requirement of typical working condition of a tracked bulldozer, the power distribution strategy for three energy sources in the front power chain was proposed by using wavelet theory and fuzzy control theory. Secondly, the electric drive system simulation platform was built in MATLAB/Simulink. At last, a driver-controller based HILS (hardware-in-the-loop simulation platform was built and the multi-energy management strategy was verified. The HILS result shows that front power chain’s power output can meet the back power chain’s requirement, the engine-generator set works near the best fuel consumption curve, and the battery pack’s charge-discharge frequency and current are low. Thus the designed multi-energy management strategy can be used in real-time control of electric drive bulldozer.

Study of non-inductive current drive using high energy neutral beam injection on JT-60U

International Nuclear Information System (INIS)

Oikawa, Toshihiro

2004-01-01

The negative ion based neutral beam (N-NB) current drive was experimentally studied. The N-NB driven current density was determined over a wide range of electron temperatures by using the motional Stark effect spectroscopy. Theoretical prediction of the NB current drive increasing with beam energy and electron temperature was validated. A record value of NB current drive efficiency 1.55 x 10 19 Am -2 W -1 was achieved simultaneously with high confinement and high beta at at a plasma current of 1.5 MA under a fully non-inductively current driven condition. The experimental validation of NB current drive theory for MHD quiescent plasmas gives greater confidence in predicting the NB current drive in future reactors. However, it was also found that MHD instabilities caused a degradation of NB current drive. A beam-driven instability expelled N-NB fast ions carrying non-inductive current from the central region. The lost N-NB driven current was estimated to be 7% of the total N-NB driven current. For the neoclassical tearing mode (NTM), comparisons of the measured neutron yield and fast ion pressure profile with transport code calculations revealed that the loss of fast ions increases with the NTM activity and that fast ions at higher energies suffer larger transport than at lower energies. (author)

Development of a hybrid energy storage sizing algorithm associated with the evaluation of power management in different driving cycles

International Nuclear Information System (INIS)

Masoud, Masih Tehrani; Mohammad Reza, Ha'iri Yazdi; Esfahanian, Vahid; Sagha, Hossein

2012-01-01

In this paper, a hybrid energy storage sizing algorithm for electric vehicles is developed to achieve a semi optimum cost effective design. Using the developed algorithm, a driving cycle is divided into its micro-trips and the power and energy demands in each micro trip are determined. The battery size is estimated because the battery fulfills the power demands. Moreover, the ultra capacitor (UC) energy (or the number of UC modules) is assessed because the UC delivers the maximum energy demands of the different micro trips of a driving cycle. Finally, a design factor, which shows the power of the hybrid energy storage control strategy, is utilized to evaluate the newly designed control strategies. Using the developed algorithm, energy saving loss, driver satisfaction criteria, and battery life criteria are calculated using a feed forward dynamic modeling software program and are utilized for comparison among different energy storage candidates. This procedure is applied to the hybrid energy storage sizing of a series hybrid electric city bus in Manhattan and to the Tehran driving cycle. Results show that a higher aggressive driving cycle (Manhattan) requires more expensive energy storage system and more sophisticated energy management strategy

Combined Use of Alcohol and Energy Drinks Increases Participation in High-Risk Drinking and Driving Behaviors Among College Students.

Science.gov (United States)

Woolsey, Conrad L; Williams, Ronald D; Housman, Jeff M; Barry, Adam E; Jacobson, Bert H; Evans, Marion W

2015-07-01

A recent study suggested that college students who combined alcohol and energy drinks were more likely than students who consumed only alcohol to drive when their blood alcohol concentration (BAC) was higher than the .08% limit and to choose to drive despite knowing they had too much alcohol to drive safely. This study sought to replicate those findings with a larger sample while also exploring additional variables related to impaired driving. College students (N = 549) completed an anonymous online survey to assess differences in drinking and driving-related behaviors between alcohol-only users (n = 281) and combined alcohol-energy drink users (n = 268). Combined users were more likely than alcohol-only users to choose to (a) drive when they perceived they were over the .08% BAC limit (35.0% vs. 18.1%, p drinks consumed, number of days drinking, number of days drunk, number of heavy episodic drinking episodes, greatest number of drinks on one occasion, and average hours of consumption. Combined use of alcohol and energy drinks may place drinkers at greater risk when compared with those who consume only alcohol. College students in this sample who combined alcohol and energy drinks were more likely to participate in high-risk driving behaviors than those who consumed only alcohol.

Driving under the influence behaviours among high school students who mix alcohol with energy drinks.

Science.gov (United States)

Wilson, Maria N; Cumming, Tammy; Burkhalter, Robin; Langille, Donald B; Ogilvie, Rachel; Asbridge, Mark

2018-06-01

Alcohol and energy drinks are commonly used substances by youth in Canada, and are often mixed (AmED). While several studies have shown that AmED can have dangerous effects, less well understood is how AmED is associated with driving under the influence of either alcohol or drugs. This study sought to determine whether youth who use AmED were more likely to engage in driving, or being a passenger of a driver, under the influence of alcohol or cannabis compared to youth who use either alcohol or energy drinks alone. This study used data from grade 10-12 students who took part in the 2014/2015 Canadian Student Tobacco, Alcohol and Drugs Survey (N=17,450). The association of past-year AmED use with past-30day: driving under the influence of alcohol or cannabis, and riding with an alcohol- or cannabis-influenced driver, was assessed using logistic regression. One in four youth had consumed AmED in the previous 12months. AmED users were more likely to engage in all risk behaviours except riding with a drinking driver, relative to youth who only consumed alcohol. No association was observed for youth who consumed alcohol and energy drinks on separate occasions. Youth who use AmED demonstrate a higher risk profile for driving under the influence of alcohol or cannabis, than youth who use alcohol alone. Future research should explore the biopsychosocial pathways that may explain why using energy drinks enhances the already heightened risk posed by alcohol on other health-related behaviours such as driving under the influence. Copyright © 2017 The Authors. Published by Elsevier Inc. All rights reserved.

New concept of electrical drives for paper and board machines based on energy efficiency principles

Directory of Open Access Journals (Sweden)

Jeftenić Borislav

2006-01-01

Full Text Available In this paper, it is described how the reconstruction of the facility of paper machine has been conducted, at the press and drying part of the machine in June 2001, as well as the expansion of the Paper Machine with the "third coating" introducing, that has been done in July 2002, in the board factory "Umka". The existing old drive of the press and the drive of drying groups were established as a Line Shaft Drive, 76 m long. The novel drive is developed on the basis of conventional squirrel cage induction motor application, with frequency converter. The system control is carried out with the programmable controller, and the communication between controllers, converters, and control boards is accomplished trough profibus. Reconstruction of the coating part of the machine, during technological reconstruction of this part of the machine, was being conducted with a purpose to improve performance of the machine by adding device for spreading "third coating". The demands for the power facility were to replace existing facility with the new one, based on energy efficiency principles and to provide adequate facility for new technological sections. Also, new part of the facility had to be connected with the remaining part of the machine, i.e. with the press and drying part, which have been reconstructed in 2001. It has to be stressed that energy efficiency principles means to realize new, modernized drive with better performances and greater capacity for the as small as possible amount of increased installed power of separate drives. In the paper are also, graphically presented achieved energy savings results, based on measurements performed on separate parts of paper machine, before and after reconstruction. .

Complexities’ day-to-day dynamic evolution analysis and prediction for a Didi taxi trip network based on complex network theory

Science.gov (United States)

Zhang, Lin; Lu, Jian; Zhou, Jialin; Zhu, Jinqing; Li, Yunxuan; Wan, Qian

2018-03-01

Didi Dache is the most popular taxi order mobile app in China, which provides online taxi-hailing service. The obtained big database from this app could be used to analyze the complexities’ day-to-day dynamic evolution of Didi taxi trip network (DTTN) from the level of complex network dynamics. First, this paper proposes the data cleaning and modeling methods for expressing Nanjing’s DTTN as a complex network. Second, the three consecutive weeks’ data are cleaned to establish 21 DTTNs based on the proposed big data processing technology. Then, multiple topology measures that characterize the complexities’ day-to-day dynamic evolution of these networks are provided. Third, these measures of 21 DTTNs are calculated and subsequently explained with actual implications. They are used as a training set for modeling the BP neural network which is designed for predicting DTTN complexities evolution. Finally, the reliability of the designed BP neural network is verified by comparing with the actual data and the results obtained from ARIMA method simultaneously. Because network complexities are the basis for modeling cascading failures and conducting link prediction in complex system, this proposed research framework not only provides a novel perspective for analyzing DTTN from the level of system aggregated behavior, but can also be used to improve the DTTN management level.

Driving range estimation for electric vehicles based on driving condition identification and forecast

Science.gov (United States)

Pan, Chaofeng; Dai, Wei; Chen, Liao; Chen, Long; Wang, Limei

2017-10-01

With the impact of serious environmental pollution in our cities combined with the ongoing depletion of oil resources, electric vehicles are becoming highly favored as means of transport. Not only for the advantage of low noise, but for their high energy efficiency and zero pollution. The Power battery is used as the energy source of electric vehicles. However, it does currently still have a few shortcomings, noticeably the low energy density, with high costs and short cycle life results in limited mileage compared with conventional passenger vehicles. There is great difference in vehicle energy consumption rate under different environment and driving conditions. Estimation error of current driving range is relatively large due to without considering the effects of environmental temperature and driving conditions. The development of a driving range estimation method will have a great impact on the electric vehicles. A new driving range estimation model based on the combination of driving cycle identification and prediction is proposed and investigated. This model can effectively eliminate mileage errors and has good convergence with added robustness. Initially the identification of the driving cycle is based on Kernel Principal Component feature parameters and fuzzy C referring to clustering algorithm. Secondly, a fuzzy rule between the characteristic parameters and energy consumption is established under MATLAB/Simulink environment. Furthermore the Markov algorithm and BP(Back Propagation) neural network method is utilized to predict the future driving conditions to improve the accuracy of the remaining range estimation. Finally, driving range estimation method is carried out under the ECE 15 condition by using the rotary drum test bench, and the experimental results are compared with the estimation results. Results now show that the proposed driving range estimation method can not only estimate the remaining mileage, but also eliminate the fluctuation of the

Estimation of directivity and sound power levels emitted by aircrafts during taxiing, for outdoor noise prediction purpose

NARCIS (Netherlands)

Asensio, C.; Pavón, I.; Ruiz, M.; Pagan Munoz, Raul; Recuero, M.

2007-01-01

Integrated noise model (INM) is the most internationally used software to calculate noise levels near airports. Take off, landing or pass by operations can be modeled by INM, but it does not consider aircrafts taxiing, which, in some cases, can be important to accurately evaluate and reduce

Design considerations for permanent magnet direct drive generators for wind energy applications

NARCIS (Netherlands)

Jassal, A.K.; Polinder, H.; Damen, M.E.C.; Versteegh, K.

2012-01-01

Permanent Magnet Direct Drive (PMDD) generators offer very high force density, high efficiency and low number of components. Due to these advantages, PMDD generators are getting popular in the wind energy industry especially for offshore application. Presence of permanent magnets gives magnetic

41 CFR 301-10.420 - When may I use a taxi, shuttle service or other courtesy transportation?

Science.gov (United States)

2010-07-01

..., shuttle service or other courtesy transportation? 301-10.420 Section 301-10.420 Public Contracts and... Courtesy Transportation § 301-10.420 When may I use a taxi, shuttle service or other courtesy... other courtesy transportation (if charges result), in the following manner: (1) At your official station...

Energy conservation strategy in Hydraulic Power Packs using Variable Frequency Drive IOP Conference Series: Materials Science and Engineering

Science.gov (United States)

Ramesh, S.; Ashok, S. Denis; Nagaraj, Shanmukha; Reddy, M. Lohith Kumar; Naulakha, Niranjan Kumar; Adithyakumar, C. R.

2018-02-01

At present, energy consumption is to such an extent that if the same trend goes on then in the future at some point of time, the energy sources will all be exploited. Energy conservation in a hydraulic power pack refers to the reduction in the energy consumed by the power pack. Many experiments have been conducted to reduce the energy consumption and one of those methods is by introducing a variable frequency drive. The main objective of the present work is to reduce the energy consumed by the hydraulic power pack using variable frequency drive. Variable Frequency drive is used to vary the speed of the motor by receiving electrical signals from the pressure switch which acts as the feedback system. Using this concept, the speed of the motor can be varied between the specified limits. In the present work, a basic hydraulic power pack and a variable frequency drive based hydraulic power pack were designed and compared both of them with the results obtained. The comparison was based on the power consumed, rise in temperature, noise levels, and flow of oil through pressure relief valve, total oil flow during loading cycle. By comparing both the circuits, it is found that for the proposed system, consumption of power reduces by 78.4% and is as powerful as the present system.

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers

Science.gov (United States)

2018-01-01

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety. PMID:29534530

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers

Directory of Open Access Journals (Sweden)

Luis Montoro

2018-03-01

Full Text Available Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety.

Work Environment, Stress, and Driving Anger: A Structural Equation Model for Predicting Traffic Sanctions of Public Transport Drivers.

Science.gov (United States)

Montoro, Luis; Useche, Sergio; Alonso, Francisco; Cendales, Boris

2018-03-12

Public transport is an effective and sustainable alternative to private vehicle usage, also helping to reduce the environmental impact of driving. However, the work environment of public transport operators is full of adverse conditions, which, together with their high mileage, may increase the occurrence of negative safety outcomes such as traffic accidents, often preceded by risky road behaviors enhanced by stress, anger, and difficult operating conditions. The aims of this study were, first, to determine the association between work-related psychosocial factors and individual characteristics of public transport drivers and the rate of traffic sanctions they are subject to; and second, to assess the mediation of driving anger in this relationship. A sample of professional drivers (57.4% city bus, 17.6% taxi, and 25% inter-urban bus male operators) was used for this cross-sectional study, responding to a five-section survey including demographic data and driving-related factors, psychosocial work factors including job stress, driving stress, risk predisposition, and driving anger. The results of this study showed significant associations between work-related factors: measures of stress and self-reported rates of traffic fines. Second, it was found that driving anger mediates the associations between driving stress, risk predisposition, and traffic sanctions; and partially mediates the association between driving experience, hourly intensity, and job stress. This study supports the idea that traffic penalties reported by public transport rates are preceded by work-related, personality, and other individual factors that, when combined with driving anger, enhance the occurrence of road misbehavior that may affect overall road safety.

What drives innovation in renewable energy technology? Evidence based on patent counts

Science.gov (United States)

McCormick, Jesse

America's future economic growth and international competitiveness depend on our capacity to innovate, particularly in emerging global markets. This paper analyzes the forces that drive innovation in one such market, renewable energy technologies, utilizing the theory of induced technological innovation. Specifically, this paper operationalizes the determinants of innovation to consist of: 1) private market forces, 2) public policy that influences price and market size, and 3) public policy that catalyzes R&D investment. Analysis is conducted using a negative binomial regression to determine which of the three foundational determinants has the greatest impact on renewable energy innovation. In so doing this paper builds off of work conducted by Johnstone et al. (2010). Innovation is measured using European Patent Office data on a panel of 24 countries spanning the period from 1978-2005. The implications of this study are straightforward; policies, not market forces, are responsible for driving innovation in renewable energy technologies. Market-oriented policies are effective for mature technologies, particularly hydro, and to a lesser extent wind and solar power. R&D-oriented policy is effective for a broader technology set. In short, the United States needs a comprehensive policy environment to support renewable energy innovation; market forces alone will not provide the pace and breadth of innovations needed. That environment can and should be strategically targeted, however, to effectively allocate scare resources.

[Comparative life cycle environmental assessment between electric taxi and gasoline taxi in Beijing].

Science.gov (United States)

Shi, Xiao-Qing; Sun, Zhao-Xin; Li, Xiao-Nuo; Li, Jin-Xiang; Yang, Jian-Xin

2015-03-01

Tailpipe emission of internal combustion engine vehicle (ICEV) is one of the main sources leading to atmospheric environmental problems such as haze. Substituting electric vehicles for conventional gasoline vehicles is an important solution for reducing urban air pollution. In 2011, as a pilot city of electric vehicle, Beijing launched a promotion plan of electric vehicle. In order to compare the environmental impacts between Midi electric vehicle (Midi EV) and Hyundai gasoline taxi (ICEV), this study created an inventory with local data and well-reasoned assumptions, and contributed a life cycle assessment (LCA) model with GaBi4.4 software and comparative life cycle environmental assessment by Life cycle impact analysis models of CML2001(Problem oriented) and EI99 (Damage oriented), which included the environmental impacts of full life cycle, manufacture phase, use phase and end of life. The sensitivity analysis of lifetime mileage and power structure was also provided. The results indicated that the full life cycle environmental impact of Midi EV was smaller than Hyundai ICEV, which was mainly due to the lower fossil fuel consumption. On the contrary, Midi EV exhibited the potential of increasing the environmental impacts of ecosystem quality influence and Human health influence. By CML2001 model, the results indicated that Midi EV might decrease the impact of Abiotic Depletion Potential, Global Warming Potential, Ozone Layer Depletion Potential and so on. However, in the production phase, the impact of Abiotic Depletion Potential, Acidification Potential, Eutrophication Potential, Global Warming Potential, Photochemical Ozone Creation Potential, Ozone Layer Depletion Potential, Marine Aquatic Ecotoxicity Potential, Terrestric Ecotoxicity Potential, Human Toxicity Potential of Midi EV were increased relative to Hyundai ICEV because of emissions impacts from its power system especially the battery production. Besides, in the use phase, electricity production was

Trip Energy Estimation Methodology and Model Based on Real-World Driving Data for Green Routing Applications: Preprint

Energy Technology Data Exchange (ETDEWEB)

Holden, Jacob [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Van Til, Harrison J [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Wood, Eric W [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Gonder, Jeffrey D [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Zhu, Lei [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2018-02-09

A data-informed model to predict energy use for a proposed vehicle trip has been developed in this paper. The methodology leverages nearly 1 million miles of real-world driving data to generate the estimation model. Driving is categorized at the sub-trip level by average speed, road gradient, and road network geometry, then aggregated by category. An average energy consumption rate is determined for each category, creating an energy rates look-up table. Proposed vehicle trips are then categorized in the same manner, and estimated energy rates are appended from the look-up table. The methodology is robust and applicable to almost any type of driving data. The model has been trained on vehicle global positioning system data from the Transportation Secure Data Center at the National Renewable Energy Laboratory and validated against on-road fuel consumption data from testing in Phoenix, Arizona. The estimation model has demonstrated an error range of 8.6% to 13.8%. The model results can be used to inform control strategies in routing tools, such as change in departure time, alternate routing, and alternate destinations to reduce energy consumption. This work provides a highly extensible framework that allows the model to be tuned to a specific driver or vehicle type.

The demand for environmental quality in driving transitions to low-polluting energy sources

International Nuclear Information System (INIS)

Fouquet, Roger

2012-01-01

The purpose of this paper is to understand the long run demand for energy-related environmental quality, its influence on legislation and on transitions to low polluting energy sources. It presents a series of episodes in British history where a demand for improvements in energy-related environmental quality existed. These episodes helped to identify a few cases where markets partially drove transitions to low polluting energy sources, in specific economic conditions. More generally, they showed that, when pushed, governments will introduce environmental legislation, although it tends to be weak and poorly enforced. In the case of air pollution, strong and binding legislation occurred roughly one hundred years later than was socially optimal. Based on this evidence, for a transition to a low carbon economy, governments will probably need to introduce focussed and binding legislation, and this cannot be expected without strong and sustained demand for climate stability. This demand will need to be spearheaded by pressure groups to introduce legislation, to enforce it and to avoid it being over-turned by future governments. - Highlights: ► Reviews demand for improvements in environmental quality in British history. ► In special cases, demand may drive transitions through markets. ► Demand will probably have to drive transitions to low polluting energy through legislation. ► Need for strong and sustained demand spearheaded through pressure groups.

Energy-efficient and safe driving using a situation-aware gamification approach in logistics

NARCIS (Netherlands)

Klemke, Roland; Kravcik, Milos; Bohuschke, Felix

2013-01-01

Klemke, R., Kravčík, M., & Bohuschke, F. (2013, 23-25 October). Energy-efficient and safe driving using a situation-aware gamification approach in logistics. Presentation at the Games and Learning Alliance Conference (GALAConf 2013), Paris, France. http://www.galaconf.org/

Injuries and absenteeism among motorcycle taxi drivers who are victims of traffic accidents.

Science.gov (United States)

Barbosa, Kevan G N; Lucas-Neto, Alfredo; Gama, Bruno D; Lima-Neto, Jose C; Lucas, Rilva Suely C C; d'Ávila, Sérgio

2014-08-01

Facial injuries frequently occur in traffic accidents involving motorcycles. The purpose of this study was to determine the prevalence of facial injuries among motorcycle drivers who perform motorcycle taxi service. The study design was cross-sectional. A total of 210 participants who served as motorcycle taxi drivers in a city in northeastern Brazil completed a survey concerning their experience of accidents involving facial injuries and consequent hospitalization and absenteeism from work. The motorcycle drivers included in the study were randomly selected from a list provided by the city. Out of the respondents, 165 (78.6%) who were involved in traffic accidents in the last 12 months, 15 (9.1%) reported facial injuries. The types of facial injury most frequently reported involved soft tissues (n = 8; 53.3%), followed by simple fracture (n = 4; 26.7%) and dentoalveolar fracture (n = 3; 20%). We found an association between facial injuries and absenteeism, as well as an association between the presence of facial injury and the need for hospitalization for a period of 2 days or more. Respondents reported that they had accidents, but due to the use of full face motorcycle helmet the number of facial injuries was low. For most of them, absenteeism was observed for a period of one month or more. Copyright © 2014 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

Multi-mode energy management strategy for fuel cell electric vehicles based on driving pattern identification using learning vector quantization neural network algorithm

Science.gov (United States)

Song, Ke; Li, Feiqiang; Hu, Xiao; He, Lin; Niu, Wenxu; Lu, Sihao; Zhang, Tong

2018-06-01

The development of fuel cell electric vehicles can to a certain extent alleviate worldwide energy and environmental issues. While a single energy management strategy cannot meet the complex road conditions of an actual vehicle, this article proposes a multi-mode energy management strategy for electric vehicles with a fuel cell range extender based on driving condition recognition technology, which contains a patterns recognizer and a multi-mode energy management controller. This paper introduces a learning vector quantization (LVQ) neural network to design the driving patterns recognizer according to a vehicle's driving information. This multi-mode strategy can automatically switch to the genetic algorithm optimized thermostat strategy under specific driving conditions in the light of the differences in condition recognition results. Simulation experiments were carried out based on the model's validity verification using a dynamometer test bench. Simulation results show that the proposed strategy can obtain better economic performance than the single-mode thermostat strategy under dynamic driving conditions.

Energy saving opportunity with variable speed drive in primary air-handling unit

International Nuclear Information System (INIS)

Li, J.S.M.

2007-01-01

Air conditioners used in the court buildings in Kowloon City, Hong Kong were retrofitted with variable speed drives in the primary air handling unit (PAU) in an effort to reduce energy consumption. The initial effect of this retrofit was investigated along with the feasibility of using a carbon dioxide (CO 2 ) based demand control ventilation to reduce energy consumption while optimizing indoor air quality. The air flow in most air conditioning fans is either constant or controlled by motorized inlet guide vanes. Although this controls the flow and may reduce the load on the fan, this constriction adds an energy loss, resulting in inefficient operation. Variable speed drives should be used on the PAU in order to maintain system efficiency. As the speed of the fans are reduced, the flow will decrease proportionally, while the power required by the fan will reduce the cube of the speed. Therefore, if the fresh air supply can be controlled by reducing the speed of the fan motor, then flow control would be more efficient. The energy saving associated with variable fresh air supply flow rate was evaluated along with the cost to building owners. This paper presented the results of the potential energy and cost savings associated with this retrofit, and included implementation cost and pay back period. It was estimated that about 20 per cent of power consumption and electricity costs can be saved per year, with a simple payback period of 2 years. 7 refs., 3 tabs., 3 figs

Suitability of Synthetic Driving Profiles from Traffic Micro-Simulation for Real-World Energy Analysis: Preprint

Energy Technology Data Exchange (ETDEWEB)

Hou, Yunfei; Wood, Eric; Burton, Evan; Gonder, Jeffrey

2015-10-14

A shift towards increased levels of driving automation is generally expected to result in improved safety and traffic congestion outcomes. However, little empirical data exists to estimate the impact that automated driving could have on energy consumption and greenhouse gas emissions. In the absence of empirical data on differences between drive cycles from present day vehicles (primarily operated by humans) and future vehicles (partially or fully operated by computers) one approach is to model both situations over identical traffic conditions. Such an exercise requires traffic micro-simulation to not only accurately model vehicle operation under high levels of automation, but also (and potentially more challenging) vehicle operation under present day human drivers. This work seeks to quantify the ability of a commercial traffic micro-simulation program to accurately model real-world drive cycles in vehicles operated primarily by humans in terms of driving speed, acceleration, and simulated fuel economy. Synthetic profiles from models of freeway and arterial facilities near Atlanta, Georgia, are compared to empirical data collected from real-world drivers on the same facilities. Empirical and synthetic drive cycles are then simulated in a powertrain efficiency model to enable comparison on the basis of fuel economy. Synthetic profiles from traffic micro-simulation were found to exhibit low levels of transient behavior relative to the empirical data. Even with these differences, the synthetic and empirical data in this study agree well in terms of driving speed and simulated fuel economy. The differences in transient behavior between simulated and empirical data suggest that larger stochastic contributions in traffic micro-simulation (relative to those present in the traffic micro-simulation tool used in this study) are required to fully capture the arbitrary elements of human driving. Interestingly, the lack of stochastic contributions from models of human drivers

Wavelength-detuning cross-beam energy transfer mitigation scheme for direct drive: Modeling and evidence from National Ignition Facility implosions

Science.gov (United States)

Marozas, J. A.; Hohenberger, M.; Rosenberg, M. J.; Turnbull, D.; Collins, T. J. B.; Radha, P. B.; McKenty, P. W.; Zuegel, J. D.; Marshall, F. J.; Regan, S. P.; Sangster, T. C.; Seka, W.; Campbell, E. M.; Goncharov, V. N.; Bowers, M. W.; Di Nicola, J.-M. G.; Erbert, G.; MacGowan, B. J.; Pelz, L. J.; Moody, J.; Yang, S. T.

2018-05-01

Cross-beam energy transfer (CBET) results from two-beam energy exchange via seeded stimulated Brillouin scattering, which detrimentally reduces laser-energy absorption for direct-drive inertial confinement fusion. Consequently, ablation pressure and implosion velocity suffer from the decreased absorption, reducing target performance in both symmetric and polar direct drive. Additionally, CBET alters the time-resolved scattered-light spectra and redistributes absorbed and scattered-light-changing shell morphology and low-mode drive symmetry. Mitigating CBET is demonstrated in inertial confinement implosions at the National Ignition Facility by detuning the laser-source wavelengths (±2.3 Å UV) of the interacting beams. In polar direct drive, wavelength detuning was shown to increase the equatorial region velocity experimentally by 16% and to alter the in-flight shell morphology. These experimental observations are consistent with design predictions of radiation-hydrodynamic simulations that indicate a 10% increase in the average ablation pressure. These results indicate that wavelength detuning successfully mitigates CBET. Simulations predict that optimized phase plates and wavelength-detuning CBET mitigation utilizing the three-legged beam layout of the OMEGA Laser System significantly increase absorption and achieve >100-Gbar hot-spot pressures in symmetric direct drive.

Design and Experiment Analysis of a Direct-Drive Wave Energy Converter with a Linear Generator

OpenAIRE

Jing Zhang; Haitao Yu; Zhenchuan Shi

2018-01-01

Coastal waves are an abundant nonpolluting and renewable energy source. A wave energy converter (WEC) must be designed for efficient and steady operation in highly energetic ocean environments. A direct-drive wave energy conversion (D-DWEC) system with a tubular permanent magnet linear generator (TPMLG) on a wind and solar photovoltaic complementary energy generation platform is proposed to improve the conversion efficiency and reduce the complexity and device volume of WECs. The operating pr...

Energy-Based Adaptive Sliding Mode Speed Control for Switched Reluctance Motor Drive

Directory of Open Access Journals (Sweden)

M. M. Namazi Isfahani

2012-03-01

Full Text Available Torque ripple minimization of switched reluctance motor drives is a major subject based on these drives’ extensive use in the industry. In this paper, by using a well-known cascaded torque control structure and taking the machine physical structure characteristics into account, the proposed energy-based (passivity-based adaptive sliding algorithm derived from the view point of energy dissipation, control stability and algorithm robustness. First, a nonlinear dynamic model is developed and decomposed into separate slow and fast passive subsystems which are interconnected by negative feedbacks. Then, an outer loop speed control is employed by adaptive sliding controller to determine the appropriate torque command. Finally, to reduce torque ripple in switched reluctance motor a high-performance passivity-based current controller is proposed. It can overcome the inherent nonlinear characteristics of the system and make the whole system robust to uncertainties and bounded disturbances. The performance of the proposed controller algorithm has been demonstrated in simulation, and experimental using a 4KW, four-phase, 8/6 pole SRM DSP-based drive system.

Accesibilidad en el transporte público en Valladolid ferrocarril, autobús y taxi

OpenAIRE

Díez Peña, Mª Begoña; Herrero Rodríguez, Sonia

2015-01-01

El objetivo de este trabajo es conocer la medida en la que se cumple la normativa de accesibilidad al transporte público en la ciudad de Valladolid, en concreto ferrocarril, autobús y taxi, no sólo en el sentido estricto de la normativa sino también desde el punto de vista de la autonomía de una persona con discapacidad física. Departamento de Organización de Empresas y Comercialización e Investigación de Mercados Máster en Logística

Electric Vehicle - Economical driving

DEFF Research Database (Denmark)

Jensen, VCE, Steen V.; Schøn, Henriette

1999-01-01

How do you reduce the energy-wast when driving and loading EV's - or rather: How do I get more km/l out of an EV......How do you reduce the energy-wast when driving and loading EV's - or rather: How do I get more km/l out of an EV...

Detuning Minimization of Induction Motor Drive System for Alternative Energy Vehicles

Directory of Open Access Journals (Sweden)

Habibur Rehman

2015-08-01

Full Text Available This paper evaluates different types of AC machines and various control techniques for their suitability for the drive system of Alternative Energy Vehicles (AEV. An Indirect Field Oriented (IFO drive system for the AEV application is chosen and its major problem of detuning is addressed by designing an offline and an online rotor resistance adaptation technique. The offline scheme sets the slip gain at various operating conditions based on the fact that if the rotor resistance is set correctly and field orientation is achieved, then there should be a linear relationship between the torque current and the output torque. The online technique is designed using Model Reference Adaptive System (MRAS for the rotor resistance adaptation. For an ideal field oriented machine, the rotor flux along the q-axis should be zero. This condition acts as a reference model for the proposed MRAS scheme. The current model flux observer in the synchronous frame of reference is selected as an adjustable model and its rotor resistance is tuned so that the flux along the q-axis becomes zero. The effectiveness of the offline tuning scheme is evident through performance validation of the drive system, which is implemented in a real Ford vehicle. The experimental results obtained while driving the test vehicle are included in the paper while the proposed online scheme is validated on a 3.75 kW prototype induction motor.

Personal exposures to airborne metals in London taxi drivers and office workers in 1995 and 1996

Energy Technology Data Exchange (ETDEWEB)

Pfeifer, G.D.; Lynam, D.R. [Air Conservation Department, Ethyl Corporation, 330 South Fourth Street, Richmond, VA (United States); Harrison, R.M. [The University of Birmingham, Environmental Health, School of Chemistry, Edgbaston, Birmingham (United Kingdom)

1999-09-01

In 1995, a petroleum marketer introduced a diesel fuel additive in the UK containing Mn as MMT (methylcyclopentadienyl manganese tricarbonyl). A small study of personal exposures to airborne Mn in London was conducted before and after introduction of the additive to identify any major impact of the additive on exposures. In 1995, personal exposures to Mn were measured in two groups, taxi drivers and office workers (10 subjects per group) for two consecutive 7-day periods. A similar study was carried out in 1996 to determine if exposures had changed. Samples were also analyzed for Ca, Al, Mg and Pb. In 1996, exposures to aerosol mass as total suspended particulates (TSP) and PM{sub 2.5} were measured in addition to the metals. Manganese exposures in this cohort did not increase as a result of introduction of the additive. However, a significant source of Mn exposure was discovered during the conduct of these tests. The mean exposure to Mn was higher among the office workers in both years than that of the taxi drivers. This was due to the fact that approximately half the office workers commuted via the underground railway system where airborne dust and metal concentrations are significantly elevated over those in the general environment. Similar results have been noted in other cities having underground rail systems. Exposure to Mn, Pb, Ca, and Mg were not significantly different between the 2 years. Taxi drivers had higher exposures than office workers to Mg and Pb in both years. Commuting via the underground also had a significant impact on exposures to TSP, PM{sub 2.5}, Al, and Ca, but had little effect on exposures to Mg. The aerosol in the underground was particularly enriched in Mn, approximately 10-fold, when compared to the aerosol in the general environment. There are several possible sources for this Mn, including mechanical wear of the steel wheels on the steel rails, vaporization of metal from sparking of the third rail, or brake wear.

ECO-DRIVING Europe - building the frame for a European market for eco-driving

International Nuclear Information System (INIS)

Raimund, Willy; Fickl, Stephan

2003-01-01

Due to rapidly increasing greenhouse gas emissions, the transport sector is a key issue in any sustainability and climate strategy. Still, it is the one most difficult to deal with because of it's complexity and direct impact on everybody's life. Innovative transport technologies can significantly contribute to reducing emissions and energy use, but there is also a need for behavioural changes to turn down energy demand, especially in individual motorised transport. One of the most cost-effective measures in this field is Ecodriving, an energy efficient and road safety improving driving style. Nowadays, there are several stand-alone initiatives in Europe. But to strengthen Ecodriving and increase its market share it needs: - an overview of existing offers and facilities, - pilot projects with different target groups, - training courses (both for novice drivers and experienced road users), - quality standards, - scientific proof of the various benefits, - awareness raising and marketing. That's why ECO-DRIVING Europe has been initiated by the main stakeholders in Europe. It aims to change the behaviour of drivers by using technological developments, influencing legislation and supporting long term driving and mobility culture change. The Europe-wide ECO-DRIVING project (www.ecodrive.org ) tries to reach this goal by integrating Ecodriving into various policy fields such as energy, climate change, road safety, local environment, sustainable transport and legislation for driver licence procedures. By decreasing greenhouse gas emission by 10-20% compared to normal driving, Ecodriving can considerably contribute to reduce energy demand in transport and fight climate change. Keywords ECO-DRIVING, sustainable transport, energy efficiency, behavioural change, market penetration, environmental and economic benefits, road safety

An Optimal Control Method for Maximizing the Efficiency of Direct Drive Ocean Wave Energy Extraction System

Science.gov (United States)

Chen, Zhongxian; Yu, Haitao; Wen, Cheng

2014-01-01

The goal of direct drive ocean wave energy extraction system is to convert ocean wave energy into electricity. The problem explored in this paper is the design and optimal control for the direct drive ocean wave energy extraction system. An optimal control method based on internal model proportion integration differentiation (IM-PID) is proposed in this paper though most of ocean wave energy extraction systems are optimized by the structure, weight, and material. With this control method, the heavy speed of outer heavy buoy of the energy extraction system is in resonance with incident wave, and the system efficiency is largely improved. Validity of the proposed optimal control method is verified in both regular and irregular ocean waves, and it is shown that IM-PID control method is optimal in that it maximizes the energy conversion efficiency. In addition, the anti-interference ability of IM-PID control method has been assessed, and the results show that the IM-PID control method has good robustness, high precision, and strong anti-interference ability. PMID:25152913

An optimal control method for maximizing the efficiency of direct drive ocean wave energy extraction system.

Science.gov (United States)

Chen, Zhongxian; Yu, Haitao; Wen, Cheng

2014-01-01

The goal of direct drive ocean wave energy extraction system is to convert ocean wave energy into electricity. The problem explored in this paper is the design and optimal control for the direct drive ocean wave energy extraction system. An optimal control method based on internal model proportion integration differentiation (IM-PID) is proposed in this paper though most of ocean wave energy extraction systems are optimized by the structure, weight, and material. With this control method, the heavy speed of outer heavy buoy of the energy extraction system is in resonance with incident wave, and the system efficiency is largely improved. Validity of the proposed optimal control method is verified in both regular and irregular ocean waves, and it is shown that IM-PID control method is optimal in that it maximizes the energy conversion efficiency. In addition, the anti-interference ability of IM-PID control method has been assessed, and the results show that the IM-PID control method has good robustness, high precision, and strong anti-interference ability.

Direct drive target survival during injection in an inertial fusion energy power plant

International Nuclear Information System (INIS)

Petzoldt, R.W.; Goodin, D.T.; Nikroo, A.; Stephens, E.; Alexander, N.B.; Gallix, R.; Siegel, N.; Raffray, A.R.; Mau, T.K.; Tillack, M.; Najmabadi, F.; Krasheninnikov, S.I.

2002-01-01

In inertial fusion energy (IFE) power plant designs, the fuel is a spherical layer of frozen DT contained in a target that is injected at high velocity into the reaction chamber. For direct drive, typically laser beams converge at the centre of the chamber (CC) to compress and heat the target to fusion conditions. To obtain the maximum energy yield from the fusion reaction, the frozen DT layer must be at about 18.5 K and the target must maintain a high degree of spherical symmetry and surface smoothness when it reaches the CC. During its transit in the chamber the cryogenic target is heated by radiation from the hot chamber wall. The target is also heated by convection as it passes through the rarefied fill-gas used to control chamber wall damage by x-rays and debris from the target explosion. This article addresses the temperature limits at the target surface beyond which target uniformity may be damaged. It concentrates on direct drive targets because fuel warm up during injection is not currently thought to be an issue for present indirect drive designs and chamber concepts. Detailed results of parametric radiative and convective heating calculations are presented for direct-drive targets during injection into a dry-wall reaction chamber. The baseline approach to target survival utilizes highly reflective targets along with a substantially lower chamber wall temperature and fill-gas pressure than previously assumed. Recently developed high-Z material coatings with high heat reflectivity are discussed and characterized. The article also presents alternate target protection methods that could be developed if targets with inherent survival features cannot be obtained within a reasonable time span. (author)

Optimal investment and scheduling of distributed energy resources with uncertainty in electric vehicle driving schedules

International Nuclear Information System (INIS)

Cardoso, G.; Stadler, M.; Bozchalui, M.C.; Sharma, R.; Marnay, C.; Barbosa-Póvoa, A.; Ferrão, P.

2014-01-01

The large scale penetration of electric vehicles (EVs) will introduce technical challenges to the distribution grid, but also carries the potential for vehicle-to-grid services. Namely, if available in large enough numbers, EVs can be used as a distributed energy resource (DER) and their presence can influence optimal DER investment and scheduling decisions in microgrids. In this work, a novel EV fleet aggregator model is introduced in a stochastic formulation of DER-CAM [1], an optimization tool used to address DER investment and scheduling problems. This is used to assess the impact of EV interconnections on optimal DER solutions considering uncertainty in EV driving schedules. Optimization results indicate that EVs can have a significant impact on DER investments, particularly if considering short payback periods. Furthermore, results suggest that uncertainty in driving schedules carries little significance to total energy costs, which is corroborated by results obtained using the stochastic formulation of the problem. - Highlights: • This paper introduces a new EV aggregator model in the DER-CAM model and expands it with a stochastic formulation. • The model is used to analyze the impact of EVs in DER investment decisions in a large office building. • The uncertainty in EV driving patterns is considered through scenarios based on data from a daily commute driving survey. • Results indicate that EVs have a significant impact in optimal DER decisions, particularly when looking at short payback periods. • Furthermore, results indicate that uncertainty in EV driving schedules has little impact on DER investment decisions

Sector trends and driving forces of global energy use and greenhouse gas emissions: focus in industry and buildings

Energy Technology Data Exchange (ETDEWEB)

Price, Lynn; Worrell, Ernst; Khrushch, Marta

1999-09-01

Disaggregation of sectoral energy use and greenhouse gas emissions trends reveals striking differences between sectors and regions of the world. Understanding key driving forces in the energy end-use sectors provides insights for development of projections of future greenhouse gas emissions. This report examines global and regional historical trends in energy use and carbon emissions in the industrial, buildings, transport, and agriculture sectors, with a more detailed focus on industry and buildings. Activity and economic drivers as well as trends in energy and carbon intensity are evaluated. The authors show that macro-economic indicators, such as GDP, are insufficient for comprehending trends and driving forces at the sectoral level. These indicators need to be supplemented with sector-specific information for a more complete understanding of future energy use and greenhouse gas emissions.

Sector trends and driving forces of global energy use and greenhouse gas emissions: focus in industry and buildings

International Nuclear Information System (INIS)

Price, Lynn; Worrell, Ernst; Khrushch, Marta

1999-01-01

Disaggregation of sectoral energy use and greenhouse gas emissions trends reveals striking differences between sectors and regions of the world. Understanding key driving forces in the energy end-use sectors provides insights for development of projections of future greenhouse gas emissions. This report examines global and regional historical trends in energy use and carbon emissions in the industrial, buildings, transport, and agriculture sectors, with a more detailed focus on industry and buildings. Activity and economic drivers as well as trends in energy and carbon intensity are evaluated. The authors show that macro-economic indicators, such as GDP, are insufficient for comprehending trends and driving forces at the sectoral level. These indicators need to be supplemented with sector-specific information for a more complete understanding of future energy use and greenhouse gas emissions

Availability, functionality, and use of seat belts in Beijing taxis prior to the 2008 Beijing Olympic Games.

Science.gov (United States)

Fleiter, Judy J; Gao, Liping; Qiu, Chen; Shi, Kan

2009-03-01

Use of driver seat belts and availability and functionality of passenger seat belts in a convenience sample of 231 Beijing taxis were examined in the months prior to the 2008 Beijing Olympic Games. Driver and front passenger seat belt use was mandated in China from 2004 to help address the growing public health crisis of road trauma. Results from observations made by in-vehicle passengers revealed that 21.2% of drivers were correctly wearing a belt, approximately half were not, and one third were using the belt in a non-functional way. Over 3/4 of this sample of taxi drivers were unrestrained while working. The percentage of functionally available belts was higher for front than rear passengers (88.3% and 22.9%, respectively). This low rate of belt availability in rear seats calls into question the preparedness of the fleet to cater for the safety needs of foreign visitors to China, particularly those from countries with high levels of restraint use. Factors influencing the use/misuse of seat belts in China remain largely unexplored. Results of this pilot study support further investigations of barriers to using injury prevention mechanisms such as seat belts in less motorised countries.

Comparison of the primary energy consumption and the CO2-emission of an urban vehicle with conventional and alternative drives

International Nuclear Information System (INIS)

Birnbreier, H.

1992-01-01

Based on a model car with its basic data corresponding to those of a series-produced small passenger car, conventional and alternative drives were compared. Cars shared the following features: same basic weight without tank, one energy storage system for the same driving range, same acceleration capacity from 0 to 50 km/h. Petrol and diesel were the conventional fuels; methanol, natural gas (pressurized, liquid), hydrogen (pressurized, liquid, hydride) and electric energy (NaS battery) were the alternative fuels. Both primary energy and CO 2 balancings take the different raw materials into account for the production of useful energies. (orig.) [de

Factores de riesgo de hipertensión arterial: prevalencia y análisis multivariable en los conductores de taxis de la ciudad de Cuenca - Ecuador, año 2014

OpenAIRE

Galarza Armijos, Mónica Eulalia; Maldonado Merino, Kathia del Cisne; Suquinagua Pintado, Geovanna Estefanía; Mosquera Vallejo, Lorena Elizabeth

2016-01-01

Objetivo: Determinar los factores de riesgo para hipertensión arterial, su prevalencia y análisis multivariable en los conductores de taxis de la ciudad de Cuenca - Ecuador, 2014. Materiales y métodos: Estudio de prevalencia de corte transversal, desarrollado en conductores de taxis residentes en Cuenca - Ecuador. Con un universo de 3 594 taxistas, para la definición del tamaño de la muestra se consideró error de estimativa de 5% y confiabilidad y precisión de la...

BOOK REVIEW: Inertial confinement fusion: The quest for ignition and energy gain using indirect drive

Science.gov (United States)

Yamanaka, C.

1999-06-01

Inertial confinement fusion (ICF) is an alternative way to control fusion which is based on scaling down a thermonuclear explosion to a small size, applicable for power production, a kind of thermonuclear internal combustion engine. This book extends many interesting topics concerning the research and development on ICF of the last 25 years. It provides a systematic development of the physics basis and also various experimental data on radiation driven implosion. This is a landmark treatise presented at the right time. It is based on the article ``Development of the indirect-drive approach to inertial confinement fusion and the target physics basis for ignition and gain'' by J.D. Lindl, published in Physics of Plasmas, Vol. 2, November 1995, pp. 3933-4024. As is well known, in the United States of America research on the target physics basis for indirect drive remained largely classified until 1994. The indirect drive approaches were closely related to nuclear weapons research at Lawrence Livermore and Los Alamos National Laboratories. In Japan and other countries, inertial confinement fusion research for civil energy has been successfully performed to achieve DT fuel pellet compression up to 1000 times normal density, and indirect drive concepts, such as the `Cannon Ball' scheme, also prevailed at several international conferences. In these circumstances the international fusion community proposed the Madrid Manifesto in 1988, which urged openness of ICF information to promote international collaboration on civil energy research for the future resources of the human race. This proposal was also supported by some of the US scientists. The United States Department of Energy revised its classification guidelines for ICF six years after the Madrid Manifesto. This first book from the USA treating target physics issues, covering topics from implosion dynamics to hydrodynamic stability, ignition physics, high-gain target design and the scope for energy applications is

The Question of Energy-Efficient Design of the Automated Electric Drive of Multi-Engine Belt Conveyors

Directory of Open Access Journals (Sweden)

Semykina Irina

2015-01-01

Full Text Available The article proposes a method for improving the energy efficiency of multi-motor variable frequency electric drives of trunk belt conveyors, based on the conveyor speed changing and controlling of the magnetic state of the motor. At conclusion, economic and energy effects of the implementation are estimated.

Comparison of Levelized Cost of Energy of superconducting direct drive generators for a 10 MW offshore wind turbine

DEFF Research Database (Denmark)

Abrahamsen, Asger Bech; Liu, Dong; Magnusson, Niklas

2018-01-01

A method for comparing the Levelized Cost of Energy (LCoE) of different superconducting drive trains is introduced. The properties of a 10 MW MgB$_{2}$ superconducting direct drive generator are presented in terms weight scaled to a turbine with a rotor diameter up of 280 m and the cost break down...

Análisis técnico de la vida útil de un lubricante de aceite mineral, para motores de combustión interna a gasolina de los vehículos de servicio de taxis de la ciudad de Cuenca

OpenAIRE

Jaramillo Sari, Diego Fernando; Redrován Macas, Luis Fernando; Urgilés Contreras, Diego René

2011-01-01

Durante el proyecto se realizó una investigación del parque automotor de taxis de la ciudad de Cuenca, determinando el tipo de aceite usado y su período de cambio. De esta manera, se plantea una encuesta, con la que se pueda determinar el tipo aceite más usado en los vehículos de servicio de taxis. El estudio se realizó en Vehículos de transporte público de servicio de taxi de la ciudad de Cuenca, porque están sometidos a periodos de funcionamiento más extensos, y producen desechos automotric...

A Functional Thinking Approach to the Design of Future Transportation Systems: Taxis as a Proxy for Personal Rapid Transit in South Korea

DEFF Research Database (Denmark)

Thompson, Mary Kathryn; Bae, Hyun Hye

2014-01-01

For over 50 years, personal rapid transit (PRT) has been viewed as one of the most promising ways to provide sustainable, economical, and convenient transportation while reducing reliance on personal automobiles. However, despite concerted efforts around the world, the promise of PRT has yet...... to be realized. This work demonstrates that different physical means, such as the Korean taxi system, can be used to perform the same highest-level functional requirement, satisfy the same constraints, and provide many of the benefits that are expected of a city-scale personal rapid transit system. Thus, Korean...... taxis can be used as an alternative embodiment of personal rapid transit and can serve as a test bed to support PRT-related design, research, and development. The paper then explores the transportation patterns and characteristics of cities in South Korea and the United States in order to determine...

Factores de riesgo de hipertensión arterial: prevalencia y análisis multivariable en los conductores de taxis de la ciudad de Cuenca - Ecuador, año 2014.

OpenAIRE

Galarza Armijos, Mónica Eulalia; Maldonado Merino, Kathia del Cisne; Suquinagua Pintado, Geovanna Estefanía; Mosquera Vallejo, Lorena Elizabeth

2016-01-01

OBJETIVO: Determinar los factores de riesgo para hipertensión arterial, su prevalencia y análisis multivariable en los conductores de taxis de la ciudad de Cuenca - Ecuador, 2014.MATERIALES Y MÉTODOS: Estudio de prevalencia de corte transversal, desarrollado en conductores de taxis residentes en Cuenca - Ecuador. Con un universo de 3 594 taxistas, para la definición del tamaño de la muestra se consideró error de estimativa de 5% y confiabilidad y precisión de la muestra en 95%, acrecidos 15% ...

Fundamental limitations on 'warp drive' spacetimes

International Nuclear Information System (INIS)

Lobo, Francisco S N; Visser, Matt

2004-01-01

'Warp drive' spacetimes are useful as 'gedanken-experiments' that force us to confront the foundations of general relativity, and among other things, to precisely formulate the notion of 'superluminal' communication. After carefully formulating the Alcubierre and Natario warp drive spacetimes, and verifying their non-perturbative violation of the classical energy conditions, we consider a more modest question and apply linearized gravity to the weak-field warp drive, testing the energy conditions to first and second orders of the warp-bubble velocity, v. Since we take the warp-bubble velocity to be non-relativistic, v << c, we are not primarily interested in the 'superluminal' features of the warp drive. Instead we focus on a secondary feature of the warp drive that has not previously been remarked upon-the warp drive (if it could be built) would be an example of a 'reaction-less drive'. For both the Alcubierre and Natario warp drives we find that the occurrence of significant energy condition violations is not just a high-speed effect, but that the violations persist even at arbitrarily low speeds. A particularly interesting feature of this construction is that it is now meaningful to think of placing a finite mass spaceship at the centre of the warp bubble, and then see how the energy in the warp field compares with the mass-energy of the spaceship. There is no hope of doing this in Alcubierre's original version of the warp field, since by definition the point at the centre of the warp bubble moves on a geodesic and is 'massless'. That is, in Alcubierre's original formalism and in the Natario formalism the spaceship is always treated as a test particle, while in the linearized theory we can treat the spaceship as a finite mass object. For both the Alcubierre and Natario warp drives we find that even at low speeds the net (negative) energy stored in the warp fields must be a significant fraction of the mass of the spaceship

Synaptic energy drives the information processing mechanisms in spiking neural networks.

Science.gov (United States)

El Laithy, Karim; Bogdan, Martin

2014-04-01

Flow of energy and free energy minimization underpins almost every aspect of naturally occurring physical mechanisms. Inspired by this fact this work establishes an energy-based framework that spans the multi-scale range of biological neural systems and integrates synaptic dynamic, synchronous spiking activity and neural states into one consistent working paradigm. Following a bottom-up approach, a hypothetical energy function is proposed for dynamic synaptic models based on the theoretical thermodynamic principles and the Hopfield networks. We show that a synapse exposes stable operating points in terms of its excitatory postsynaptic potential as a function of its synaptic strength. We postulate that synapses in a network operating at these stable points can drive this network to an internal state of synchronous firing. The presented analysis is related to the widely investigated temporal coherent activities (cell assemblies) over a certain range of time scales (binding-by-synchrony). This introduces a novel explanation of the observed (poly)synchronous activities within networks regarding the synaptic (coupling) functionality. On a network level the transitions from one firing scheme to the other express discrete sets of neural states. The neural states exist as long as the network sustains the internal synaptic energy.

Factors associated with drug use among male motorbike taxi drivers in urban Vietnam.

Science.gov (United States)

Nguyen, Huy Van; Vu, Thinh Toan; Pham, Ha Nguyen

2014-08-01

A cross-sectional study was conducted on a sample of 291 male motorbike taxi drivers (MMTDs) recruited through social mapping technique in Hanoi, Vietnam, for face-to-face interviews to examine factors associated with drug use among MMTDs using Information-Motivation-Behavioral skills (IMB) model. Among 291 MMTDs, 17.18% reported drug use sometime in their lives, 96% of whom were drug injectors. Being depressed, being originally borne in urban cities, currently residing in rural areas, having a longer time living apart from their wives/lovers, using alcohol, following Buddhism, and reporting lower motivation of HIV prevention predict significantly higher odds of uptaking drugs.

Influence of Tire Characteristics of Interurban Taxis on Exposure Level to Drivers Whole-Body Vibrations

Directory of Open Access Journals (Sweden)

Milad Derakhshanjazari

2016-03-01

Full Text Available Introduction: Taxi drivers’ exposure to repeat whole-body vibrations can cause back pain and digestive disorders. Since this type of vibration depends on the car components, this study was carried out to determine the influence of tire characteristics on the amount of whole-body vibrations transmitted to the Peugeot 405 taxi drivers. Methods: In this experimental study, vibration characteristics were measured according to the ISO2631-1 with each of the statuses: tubeless tires fixed and fluid in it (normal air or nitrogen and also the fluid in the tires fixed with tubes or tubeless on asphalt-paved road. Other variables including tire pressure, engine speed, road gradient, number of passengers, springs, and shock absorbers were kept constant. Then the effect of changes was analyzed using an appropriate statistical test. Results: After changing nitrogen to normal air and tubeless tires to tube, the average of RMS in Z-axis, eight-hour equivalent acceleration A(8 and crest factor were reduced (P 0.9 m/s2 to caution zone (0.45-0.9 m/s2 with a value of 0.8 m/s2. Conclusions: The amount of vibration transmitted to the whole body is sensitive to existence of tubes and tires inflation so that we can reduce the amount of whole-body vibration to lower than the upper limit of the health risk by changing the characteristics of the tire

Assessment and cleanup of the Taxi Strip waste storage area at LLNL [Lawrence Livermore National Laboratory

International Nuclear Information System (INIS)

Buerer, A.

1983-01-01

In September 1982 the Hazards Control Department of the Lawrence Livermore National Laboratory (LLNL) began a final radiological survey of a former low-level radioactive waste storage area called the Taxi Strip so that the area could be released for construction of an office building. Collection of soil samples at the location of a proposed sewer line led to the discovery of an old disposal pit containing soil contaminated with low-level radioactive waste and organic solvents. The Taxi Strip area was excavated leading to the discovery of three additional small pits. The clean-up of Pit No. 1 is considered to be complete for radioactive contamination. The results from the chlorinated solvent analysis of the borehole samples and the limited number of samples analyzed by gas chromatography/mass spectrometry indicate that solvent clean-up at this pit is complete. This is being verified by gas chromatography/mass spectrometry analysis of a few additional soil samples from the bottom sides and ends of the pit. As a precaution, samples are also being analyzed for metals to determine if further excavation is necessary. Clean-up of Pits No. 2 and No. 3 is considered to be complete for radioactive and solvent contamination. Results of analysis for metals will determine if excavation is complete. Excavation of Pit No. 4 which resulted from surface leakage of radioactive contamination from an evaporation tray is complete

Determining of the Parking Manoeuvre and the Taxi Blockage Adjustment Factor for the Saturation Flow Rate at the Outlet Legs of Signalized Intersections: Case Study from Rasht City (Iran)

Science.gov (United States)

Behbahani, Hamid; Jahangir Samet, Mehdi; Najafi Moghaddam Gilani, Vahid; Amini, Amir

2017-10-01

The presence of taxi stops within the area of signalized intersections at the outlet legs due to unnatural behaviour of the taxis, sudden change of lanes, parking manoeuvres activities and stopping the vehicle to discharge or pick up the passengers have led to reduction of saturation flow rate at the outlet leg of signalized intersections and increased delay as well as affecting the performance of a crossing lane. So far, in term of evaluating effective adjustment factors on saturation flow rate at the inlet legs of the signalized intersections, various studies have been carried out, however; there has not been any studies on effective adjustment factors on saturation flow rate at the inlet legs. Hence, the evaluating of the traffic effects of unique behaviours on the saturation flow rate of the outlet leg is very important. In this research the parking manoeuvre time and taxi blockage time were evaluated and analyzed based on the available lane width as well as determining the effective adjustment factors on the saturation flow rate using recording related data at four signalized intersections in Rasht city. The results show that the average parking manoeuvre time is a function of the lane width and is increased as the lane width is reduced. Also, it is suggested to use the values of 7.37 and 11.31 seconds, respectively for the average parking manoeuvre time and the average blockage time of taxies at the outlet legs of signalized intersections for the traffic designing in Rasht city.

Large-Scale Battery System Development and User-Specific Driving Behavior Analysis for Emerging Electric-Drive Vehicles

Directory of Open Access Journals (Sweden)

Yihe Sun

2011-04-01

Full Text Available Emerging green-energy transportation, such as hybrid electric vehicles (HEVs and plug-in HEVs (PHEVs, has a great potential for reduction of fuel consumption and greenhouse emissions. The lithium-ion battery system used in these vehicles, however, is bulky, expensive and unreliable, and has been the primary roadblock for transportation electrification. Meanwhile, few studies have considered user-specific driving behavior and its significant impact on (PHEV fuel efficiency, battery system lifetime, and the environment. This paper presents a detailed investigation of battery system modeling and real-world user-specific driving behavior analysis for emerging electric-drive vehicles. The proposed model is fast to compute and accurate for analyzing battery system run-time and long-term cycle life with a focus on temperature dependent battery system capacity fading and variation. The proposed solution is validated against physical measurement using real-world user driving studies, and has been adopted to facilitate battery system design and optimization. Using the collected real-world hybrid vehicle and run-time driving data, we have also conducted detailed analytical studies of users’ specific driving patterns and their impacts on hybrid vehicle electric energy and fuel efficiency. This work provides a solid foundation for future energy control with emerging electric-drive applications.

Exploring the effects of driving experience on hazard awareness and risk perception via real-time hazard identification, hazard classification, and rating tasks.

Science.gov (United States)

Borowsky, Avinoam; Oron-Gilad, Tal

2013-10-01

This study investigated the effects of driving experience on hazard awareness and risk perception skills. These topics have previously been investigated separately, yet a novel approach is suggested where hazard awareness and risk perception are examined concurrently. Young, newly qualified drivers, experienced drivers, and a group of commercial drivers, namely, taxi drivers performed three consecutive tasks: (1) observed 10 short movies of real-world driving situations and were asked to press a button each time they identified a hazardous situation; (2) observed one of three possible sub-sets of 8 movies (out of the 10 they have seen earlier) for the second time, and were asked to categorize them into an arbitrary number of clusters according to the similarity in their hazardous situation; and (3) observed the same sub-set for a third time and following each movie were asked to rate its level of hazardousness. The first task is considered a real-time identification task while the other two are performed using hindsight. During it participants' eye movements were recorded. Results showed that taxi drivers were more sensitive to hidden hazards than the other driver groups and that young-novices were the least sensitive. Young-novice drivers also relied heavily on materialized hazards in their categorization structure. In addition, it emerged that risk perception was derived from two major components: the likelihood of a crash and the severity of its outcome. Yet, the outcome was rarely considered under time pressure (i.e., in real-time hazard identification tasks). Using hindsight, when drivers were provided with the opportunity to rate the movies' hazardousness more freely (rating task) they considered both components. Otherwise, in the categorization task, they usually chose the severity of the crash outcome as their dominant criterion. Theoretical and practical implications are discussed. Copyright © 2013 Elsevier Ltd. All rights reserved.

An Investigation on the Effect of Driver Style and Driving Events on Energy Demand of a PHEV

OpenAIRE

Rajan, Brahmadevan; McGordon, Andrew; Jennings, Paul

2012-01-01

Environmental concerns, security of fuel supply and CO2 regulations are driving innovation in the automotive industry towards electric and hybrid electric vehicles. The fuel economy and emission performance of hybrid electric vehicles (HEVs) strongly depends on the energy management system (EMS). Prior knowledge of driving information could be used to enhance the performance of a HEV. However, how the necessary information can be obtained to use in EMS optimisation still remains a challenge. ...

Optimal investment and scheduling of distributed energy resources with uncertainty in electric vehicles driving schedules

Energy Technology Data Exchange (ETDEWEB)

Cardoso, Goncalo [Technical Univ. of Lisbon (Portugal); Stadler, Michael [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Center for Energy and Innovation Technologies (Austria); Bozchalui, Mohammed C. [NEC Laboratories American Inc., Irving, TX (United States); Sharma, Ratnesh [NEC Laboratories American Inc., Irving, TX (United States); Marnay, Chris [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Barbosa-Povoa, Ana [Technical Univ. of Lisbon (Portugal); Ferrao, Paulo [Technical Univ. of Lisbon (Portugal)

2013-12-06

The large scale penetration of electric vehicles (EVs) will introduce technical challenges to the distribution grid, but also carries the potential for vehicle-to-grid services. Namely, if available in large enough numbers, EVs can be used as a distributed energy resource (DER) and their presence can influence optimal DER investment and scheduling decisions in microgrids. In this work, a novel EV fleet aggregator model is introduced in a stochastic formulation of DER-CAM [1], an optimization tool used to address DER investment and scheduling problems. This is used to assess the impact of EV interconnections on optimal DER solutions considering uncertainty in EV driving schedules. Optimization results indicate that EVs can have a significant impact on DER investments, particularly if considering short payback periods. Furthermore, results suggest that uncertainty in driving schedules carries little significance to total energy costs, which is corroborated by results obtained using the stochastic formulation of the problem.

Comparison Of Taxis And Logical Semantic Systems In Indonesian And Malaysian Newspapers About Airasia Qz8501 Accident

OpenAIRE

Syahputra, Yudha

2016-01-01

This study seeks to describe the comparative portion of taxis and logical semantic systems between Malaysian and Indonesian newspapers’ articles about AirAsia QZ8501 accident. The data are clause complexes in Indonesia naval captain says may have located missing plane tail’s section’s New Straits Times (Text A) and AirAsia tail section located, blackbox still missing’s The Jakarta Post (Text B) articles. This study uses qualitative-descriptive method. As the result, both par...

Energy efficient drives and control engineering. Intelligent machine and plant concepts for manufacturing; Energieeffiziente Antriebs- und Steuerungstechnik. Intelligente Maschinen- und Anlagenkonzepte fuer die Fertigung

Energy Technology Data Exchange (ETDEWEB)

Fahrbach, Christian; Frank, Klaus; Haack, Steffen; Schemm, Eberhardt; Wittschen, Wiebke

2010-07-01

The book discusses the potential of intelligent and energy-efficient drive and control concepts. It shows that energy efficient components - pumps, motors, or speed-controlled pump drives - may result in a double-digit reduction of energy consumption. The effect is even more pronounced when the system is opotimized as a whole. If energy-efficient components are combined so that a direct energy flow will result, energy will be converted on demand, i.e. the right amount at the right time. The book also discusses how these design options can be applied in the various phases of the machine life cycle.

An investigation on the effect of driver style and driving\\ud events on energy demand of a PHEV

OpenAIRE

Padmarajan, Brahmadevan V.; McGordon, Andrew; Jennings, P. A. (Paul A.)

2012-01-01

Environmental concerns, security of fuel supply and CO2 regulations are driving innovation in the automotive industry towards electric and hybrid electric vehicles. The fuel economy and emission performance of hybrid electric vehicles (HEVs) strongly depends on the energy management system (EMS). Prior knowledge of driving information could be used to enhance the performance of a HEV. However, how the necessary information can be obtained to use in EMS optimisation still remains a challenge. ...

Estudio de la vida útil de los vehículos desde la perspectiva de la gestión de mantenimiento del transporte público modalidad taxis de la ciudad de Cuenca

OpenAIRE

Espinoza Sibri, Víctor Geovanny; Ortega Lema, Edwin Paúl; Sancho Carchipulla, Marco Vinicio

2012-01-01

La (ANT) Agencia Nacional de Transporte, Transito y Seguridad Vial ha establecido que la vida útil de los vehículos de servicio público modalidad taxis es de 10 años, por lo tanto en el desarrollo de la presente tesis se ha comprobado desde la perspectiva de la gestión de mantenimiento, si se cumple lo determinado por la entidad. Actualmente existe un total de 3555 unidades de taxis vigentes de distinta marca, modelo y año de fabricación que prestan su servicio de transporte a todos los ha...

Comparison of electric drives for road vehicles

Energy Technology Data Exchange (ETDEWEB)

Bader, C; Stephan, W [Deutsche Automobilgesellschaft m.b.H., Esslingen (Germany, F.R.)

1977-01-01

The low energy-storage capacity of the electrolytic energy-storage apparatus available at the moment limits the practical use of electric vehicles to meeting the requirements for restricted areas. But in this field of application, conversion from drive with internal combustion engine to electric drive can be considered only if a reduction of costs is achieved with electric drive. From the wide range of possible drive units the most suitable is found to be the dc squirrelcage motor the speed of which is controlled by field weakening. In the case of a motor with conventional design, the controllable drive range is limited to about 1 : 3, so that generally additional measures are required for extending the drive range. But if the motor is fitted with a compensation winding, field weakening to give a controlled speed range of 1 : 8 can be obtained. To evaluate the different drive units under consideration use is made of the acceleration when, according to the drive system, advantages are obtained from the point of view of energy consumption with disadvantages in acceleration time, and vice versa. By using vehicles proven in practice with different drive systems, either with hydrodynamic transducer and battery switchover, or else with changeover gear and mechanical clutch, the overall construction of the different control and protective arrangements are demonstrated. It is then found that the extra cost of regulation in the case of automatic drive operation is partly compensated by the additional protective devices which are required to limit the effects of any incorrect operations with a manually-operated drive.

Advanced drive package saves energy. Synchronous reluctance motor with frequency converter; Energiesparpaket der Zukunft. Synchronreluktanzmotor und Frequenzumrichter

Energy Technology Data Exchange (ETDEWEB)

Donabauer, Fred [ABB Automation Products GmbH, Ladenburg (Germany); Lendenmann, Heinz [ABB AB, Vaesteras (Sweden)

2011-07-01

The drive package consisting of a synchronous reluctance motor and a frequency converters with Direct Torque Control (DTC) reaches a high level of efficiency and can make a substantial contribution to energy saving in many drive applications. The motor needs no permanent magnets or excitation system. The synchronous reluctance motor is up to two sizes smaller than an induction motor with a similar output and its power density is up to 40% higher than that of an induction motor. A frequency converter with DTC enables exact speed control without requiring an encoder. (orig.)

[Driving forces of carbon emission from energy consumption in China old industrial cities: a case study of Shenyang City, Northeast China].

Science.gov (United States)

Ren, Wan-Xia; Geng, Yong; Xue, Bing

2012-10-01

To quantitatively analyze the effects of anthropogenic factors on regional environmental quality is a hot topic in the field of sustainable development research. Taking the typical old industrial city Shenyang in Northeast China as a case, and by using the IPCC method for calculating carbon emission from energy consumption, this paper estimated the carbon emission from energy consumption in the city in 1978-2009, and a time series analysis on the anthropogenic factors driving this carbon emission was made by the STIRPAT model based upon Kaya equation and ridge regression. In 1978-2009, the carbon emission in the city had a slow increase first, slow decrease then, and a rapid increase thereafter. The total carbon emission in 2009 was 4.6 times of that in 1978. Population growth was the main factor driving the growth of the emission, and there existed an equal-proportional variation between the population growth and the carbon emission growth. Urbanization was another main driving factor followed by population growth, and the per capita GDP was positively correlated with the carbon emission. Kuznets curve did not exist for the relationship between economic development and carbon emission in Shenyang. Energy source intensity reduction (representing technology improvement) was the main factor driving the reduction of the total carbon emission.

Analyzing driving forces behind changes in energy vulnerability of Spanish electricity generation through a Divisia index-based method

International Nuclear Information System (INIS)

Fernández González, P.; Moreno, B.

2015-01-01

Highlights: • We propose and develop the LMDI approach to factorize changes in electricity bill vulnerability. • Spanish vulnerability (1995–2011) markedly grew mainly by increasing gas dependence. • Fuel price increase and growing importance of electricity damage energy security. • Energy intensity advances & fuel diversification: insufficient to drive vulnerability. • Main recommendation: enhance internal energy market and common external EU strategy. - Abstract: High energy dependence on fossil raises vulnerability concerns about security of supply and energy cost. This research examines the impact of high dependence of imported fuels for power generation in Spain through the quantification and analysis of the driving forces behind the change in its electricity bill. Following logarithmic mean Divisia indexes approach, we present and perform a new method that enables a complete decomposition of changes in electricity vulnerability into contributions from several drivers. In fact, we identify five predefined factors behind the variations in vulnerability in Spain during the 1998–2011 period: fuel price, average heat rate, fuel dependence, degree of electricity importance and energy intensity. The application of this approach reveals a significant increase in Spanish vulnerability in the last two decades, promoted by increments in fuel price and importance of electricity over the primary energy consumption, but especially by increasing fuel dependence (particularly gas dependence). Therefore, findings mainly advocate for those strategies aimed at reducing Spanish energy dependence. Also those improving thermal efficiency and energy intensity are indicated

Wind generator with electronic variable-speed drives

Energy Technology Data Exchange (ETDEWEB)

David, A.; Buchheit, N.; Jakobsen, H.

1996-12-31

Variable speed drives have been inserted between the network and the generator on certain recent wind power facilities. They have the following advantages: the drive allows the wind generator to operate at low speed with a significant reduction in acoustic noise, an important point if the facilities are sited near populated areas; the drive optimizes energy transfer, providing a gain of 4 to 10 %; the drive can possibly replace certain mechanical parts (the starting system and it in some cases, the reduction gear); the drive not only provides better transient management in relation to the network for less mechanical stress on the wind generator, it is also able to control reactive power. One commercial drive design sold by several manufacturers has already been installed on several wind generators with outputs of between 150 and 600 kw. In addition, such a solution is extremely well suited to mixed renewable energy systems. This design uses two inverse rectifier type converters and can therefore exchange energy in both directions. The equivalent drive with a single IGBT converter on the motor side and a diode converter on the network side is the solution most widely adopted throughout industry (with more than 50, 000 units installed in France per year). It still remains to be seen whether such a solution could be profitable in wind generator application (since the cost of the drive is quite high). This technical analysis is more destined for the converter-machine assembly specialists and is presented in this document, paying particular attention as it does to the modelling of the `wind energy - generator - drive - network` assembly, the associated drive command and control strategies and the simulations obtained during various transients. A 7.5 kW test bed has been installed in the Laboratoire d`Electronique de Puissance de Clamart, enabling tests to be carried out which emulate the operation of a wind generator.

[Reliability and validity of Driving Anger Scale in professional drivers in China].

Science.gov (United States)

Li, Z; Yang, Y M; Zhang, C; Li, Y; Hu, J; Gao, L W; Zhou, Y X; Zhang, X J

2017-11-10

Objective: To assess the reliability and validity of the Chinese version of Driving Anger Scale (DAS) in professional drivers in China and provide a scientific basis for the application of the scale in drivers in China. Methods: Professional drivers, including taxi drivers, bus drivers, truck drivers and school bus drivers, were selected to complete the questionnaire. Cronbach's α and split-half reliability were calculated to evaluate the reliability of DAS, and content, contract, discriminant and convergent validity were performed to measure the validity of the scale. Results: The overall Cronbach's α of DAS was 0.934 and the split-half reliability was 0.874. The correlation coefficient of each subscale with the total scale was 0.639-0.922. The simplified version of DAS supported a presupposed six-factor structure, explaining 56.371% of the total variance revealed by exploratory factor analysis. The DAS had good convergent and discriminant validity, with the success rate of calibration experiment of 100%. Conclusion: DAS has a good reliability and validity in professional drivers in China, and the use of DAS is worth promoting in divers.

Alternative drives for motor cars. Hybrid systems, fuel cells, alternative energy sources. 3. ed.; Alternative Antriebe fuer Automobile. Hybridsysteme, Brennstoffzellen, alternative Energietraeger

Energy Technology Data Exchange (ETDEWEB)

Stan, Cornel [California Univ., Berkeley, CA (United States); Paris-1 Univ., 75 (France); Pisa Univ. (Italy); Perugia Univ. (Italy); Kronstadt Univ. (Russian Federation)

2012-07-01

This book describes and assesses on the basis of the latest research and development projects worldwide what the possibilities are for the realisation of future drive concepts, ranging from battery-driven electromotors to hybrid systems combining electromotor and combustion engine to alternative energy resources such as hydrogen or alcohol. Power density, torque band, acceleration characteristics, specific energy consumption and chemical and noise emissions are the most important criteria for assessing the quality of a drive configuration. The boundary conditions for the introduction of alternative automotive drives are determined by the availability or production characteristics and the storability of the energy resources in question as well as by the degree of technical complexity, costs, safety, infrastructure and service. This book provides an updated overview and analysis of the processes, prime movers and energy resources that can be combined in complex energy management systems for automobiles. Up-to-date information of this kind is indispensable for the development of new concepts. The contents in overview: current data and facts on the development of new concepts; compact overview and analysis of processes, prime movers and energy resources; methods and solutions in designing alternative drives. [German] Die Realisierungsmoeglichkeiten zukuenftiger Antriebskonzepte - von batteriebetriebenen Elektromotoren und Hybridsystemen bestehend aus Elektro- und Verbrennungsmotor ueber Brennstoffzellen bis hin zu alternativen Energietraegern wie Wasserstoff oder Alkohol - werden auf Basis neuesten Forschungs- und Entwicklungsarbeiten weltweit praesentiert und bewertet. Leistungsdichte, Drehmomentverlauf, Beschleunigungscharakteristik, spezifischer Energieverbrauch sowie Emission chemischer Stoffe und Geraeusche sind wichtige Merkmale zur Beurteilung der Qualitaet einer Antriebskonfiguration. Die Verfuegbarkeit oder die Herstellungsmerkmale sowie die Speicherfaehigkeit

Progress toward ignition with direct-drive

International Nuclear Information System (INIS)

McCrory, R.L. Jr.

1993-01-01

The goal of the direct-drive laser fusion program is to validate high-performance, direct-drive targets. A decision to construct a direct-drive capability on the proposed 1-to-2-MJ National Ignition Facility (NIF) in the USA will be based on target physics experiments conducted on the OMEGA Upgrade laser system now under construction at the LLE. The OMEGA Upgrade will provide up to 30 kJ of UV laser energy in precisely shaped pulses with irradiation nonuniformities in the range of 1 pc. to 2 pc. An understanding and predictive capability for direct-drive targets are required to assure reliable estimates of ignition and gain with 1-2 MJ of incident laser energy. This paper reviews the target physics efforts currently underway to assess the critical physics issues of direct-drive ICF; plans for the experimental program to be carried out on the OMEGA Upgrade laser are also presented. 14 figs., 15 refs

Features of electric drive sucker rod pumps for oil production

Science.gov (United States)

Gizatullin, F. A.; Khakimyanov, M. I.; Khusainov, F. F.

2018-01-01

This article is about modes of operation of electric drives of downhole sucker rod pumps. Downhole oil production processes are very energy intensive. Oil fields contain many oil wells; many of them operate in inefficient modes with significant additional losses. Authors propose technical solutions to improve energy performance of a pump unit drives: counterweight balancing, reducing of electric motor power, replacing induction motors with permanent magnet motors, replacing balancer drives with chain drives, using of variable frequency drives.

Optimal Airport Surface Traffic Planning Using Mixed-Integer Linear Programming

Directory of Open Access Journals (Sweden)

P. C. Roling

2008-01-01

Full Text Available We describe an ongoing research effort pertaining to the development of a surface traffic automation system that will help controllers to better coordinate surface traffic movements related to arrival and departure traffic. More specifically, we describe the concept for a taxi-planning support tool that aims to optimize the routing and scheduling of airport surface traffic in such a way as to deconflict the taxi plans while optimizing delay, total taxi-time, or some other airport efficiency metric. Certain input parameters related to resource demand, such as the expected landing times and the expected pushback times, are rather difficult to predict accurately. Due to uncertainty in the input data driving the taxi-planning process, the taxi-planning tool is designed such that it produces solutions that are robust to uncertainty. The taxi-planning concept presented herein, which is based on mixed-integer linear programming, is designed such that it is able to adapt to perturbations in these input conditions, as well as to account for failure in the actual execution of surface trajectories. The capabilities of the tool are illustrated in a simple hypothetical airport.

Energy Research 2006 - Overview; Recherche energetique/Energie-Forschung 2006. Rapports de synthese des chefs de programme/Ueberblicksberichte der Programmleiter. Konzept der Energieforschung des Bundes

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-05-15

This comprehensive annual report for the Swiss Federal Office of Energy (SFOE) contains the overview-reports for the year 2006 that were made by the heads of the following Swiss energy research programmes: Efficient energy use, renewable energy, nuclear energy and fundamentals of energy economics. Under the topic of efficient energy use, new planning tools and a building component catalogue are mentioned along with new developments in building technology. In the traffic area, energy-optimisation of components and drive systems are mentioned as are electric bikes and a taxi system running on tracks. High-temperature superconductors, permanent magnet motors along with alternative power generation and storage systems are reviewed. New electricity grid systems and energy hubs are reported on. In the heat pump area, hot-water preparation, quality assurance and magnetic heat pumps are listed. Combustion topics reviewed include large diesel engines and catalytic oxidation in gas turbines. The new 'Power Station 2020' program is introduced with combined heat and power stations and efficient gas turbines. Fuel cells and hydrogen production and storage are looked at, as are process integration topics in the industrial area. Renewable energy topics described include design software and testing systems for solar heating systems, thin-film photovoltaics, industrial use of solar energy and solar production of hydrogen. Biomass and wood-fuel topics are covered, including the gasification of biomass. Cost reduction in small-scale hydro schemes is reported on as are hydropower schemes using drinking water and waste water. Geothermal energy and deep-heat mining are reported on, as is the use of geothermal probes for heating and cooling. Research and field testing done in the wind-energy area and the social acceptance of such installations are presented. In the nuclear energy area, safety and waste disposal issues are covered, as are a future reactor generation, safety research and

Energy Research 2006 - Overview; Recherche energetique/Energie-Forschung 2006. Rapports de synthese des chefs de programme/Ueberblicksberichte der Programmleiter. Konzept der Energieforschung des Bundes

Energy Technology Data Exchange (ETDEWEB)

NONE

2007-05-15

This comprehensive annual report for the Swiss Federal Office of Energy (SFOE) contains the overview-reports for the year 2006 that were made by the heads of the following Swiss energy research programmes: Efficient energy use, renewable energy, nuclear energy and fundamentals of energy economics. Under the topic of efficient energy use, new planning tools and a building component catalogue are mentioned along with new developments in building technology. In the traffic area, energy-optimisation of components and drive systems are mentioned as are electric bikes and a taxi system running on tracks. High-temperature superconductors, permanent magnet motors along with alternative power generation and storage systems are reviewed. New electricity grid systems and energy hubs are reported on. In the heat pump area, hot-water preparation, quality assurance and magnetic heat pumps are listed. Combustion topics reviewed include large diesel engines and catalytic oxidation in gas turbines. The new 'Power Station 2020' program is introduced with combined heat and power stations and efficient gas turbines. Fuel cells and hydrogen production and storage are looked at, as are process integration topics in the industrial area. Renewable energy topics described include design software and testing systems for solar heating systems, thin-film photovoltaics, industrial use of solar energy and solar production of hydrogen. Biomass and wood-fuel topics are covered, including the gasification of biomass. Cost reduction in small-scale hydro schemes is reported on as are hydropower schemes using drinking water and waste water. Geothermal energy and deep-heat mining are reported on, as is the use of geothermal probes for heating and cooling. Research and field testing done in the wind-energy area and the social acceptance of such installations are presented. In the nuclear energy area, safety and waste disposal issues are covered, as are a future reactor generation, safety

CORONARY ARTERY DISEASE RISK FACTORS IN DRIVERS VERSUS PEOPLE IN OTHER OCCUPATIONS

Directory of Open Access Journals (Sweden)

Hamidreza Nasri

2010-12-01

Full Text Available   Abstract INTRODUCTION: The link between occupational factors and coronary artery diseases (CAD has been studied and confirmed in many countries. Conditions associated with driving such as stress, and factors such as long working hours and the environment can increase the risk of CAD. In this study, we measured potential CAD risk factors in bus and taxi drivers and compared them with a control group. methods: 135 taxi drivers, 194 bus drivers and 121 non-drivers (control group were evaluated for CAD risk factors, i.e. age, body mass index (BMI>24, cigarette smoking, hypertension, high-density and low-density lipoprotein cholesterol (HDL, LDL, triglyceride >200, blood sugar >126 and familial history of CAD. Univariate and multivariate logistic regression tests were used to distinguish major risk factors. results: Taxi drivers have an increased risk of hypertension compared with the control group (odds ratio: crude=5.94, adjusted=9.09; P<0001. Cigarette smoking in taxi and bus drivers was 1.4 (P<0.3 and 3.24 (P<0001 times as high as the control group, respectively. The risk of increased LDL and decreased HDL in bus drivers was 4.38 and 5.28 (P<0001 times as high as the control group, respectively. The risk of obesity, high blood sugar and high triglyceride was not significantly different between the groups. CONCLUSIONS: Driving is an independent risk factor for hypertension. Known CAD risk factors are also more frequent in drivers.     Keywords: Driving, cardiovascular disease, risk factor.

Efficient Solar Energy Harvesting and Storage through a Robust Photocatalyst Driving Reversible Redox Reactions.

Science.gov (United States)

Zhou, Yangen; Zhang, Shun; Ding, Yu; Zhang, Leyuan; Zhang, Changkun; Zhang, Xiaohong; Zhao, Yu; Yu, Guihua

2018-06-14

Simultaneous solar energy conversion and storage is receiving increasing interest for better utilization of the abundant yet intermittently available sunlight. Photoelectrodes driving nonspontaneous reversible redox reactions in solar-powered redox cells (SPRCs), which can deliver energy via the corresponding reverse reactions, present a cost-effective and promising approach for direct solar energy harvesting and storage. However, the lack of photoelectrodes having both high conversion efficiency and high durability becomes a bottleneck that hampers practical applications of SPRCs. Here, it is shown that a WO 3 -decorated BiVO 4 photoanode, without the need of extra electrocatalysts, can enable a single-photocatalyst-driven SPRC with a solar-to-output energy conversion efficiency as high as 1.25%. This SPRC presents stable performance over 20 solar energy storage/delivery cycles. The high efficiency and stability are attributed to the rapid redox reactions, the well-matched energy level, and the efficient light harvesting and charge separation of the prepared BiVO 4 . This demonstrated device system represents a potential alternative toward the development of low-cost, durable, and easy-to-implement solar energy technologies. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Performance improvement of a slip energy recovery drive system by a voltage-controlled technique

Energy Technology Data Exchange (ETDEWEB)

Tunyasrirut, Satean [Department of Instrumentation Engineering, Faculty of Engineering, Pathumwan Institute of Technology, 833 Rama1 Road, Pathumwan, Bangkok 10330 (Thailand); Kinnares, Vijit [Department of Electrical Engineering, Faculty of Engineering, King Mongkut' s Institute of Technology Ladkrabang, Bangkok 10520 (Thailand); Ngamwiwit, Jongkol [Department of Control Engineering, Faculty of Engineering, King Mongkut' s Institute of Technology Ladkrabang, Bangkok 10520 (Thailand)

2010-10-15

This paper introduces the performance improvement of a slip energy recovery drive system for the speed control of a wound rotor induction motor by a voltage-controlled technique. The slip energy occurred in the rotor circuit is transferred back to ac mains supply through a reactor instead of a step up transformer. The objective of the voltage-controlled technique is to increase power factor of the system and to reduce low order harmonics of the input line current. The drive system is designed and implemented using a voltage source inverter in conjunction with a boost chopper for DC link voltage, instead of a conventional drive using a 6 pulse converter or a Scherbius system. The slip power is recovered by the help of a voltage source inverter (VSI) based on a space vector pulse width modulation (SVPWM) technique. In order to keep the speed of the wound rotor induction motor constant over a certain range of operating conditions, the servo state feedback controller designed by a linear quadratic regulator (LQR) is also introduced in this paper. The overall control system is implemented on DSP, DS1104'TMS320F240 controller board. The performance improvement of the proposed system is tested in comparison with the conventional Scherbius system and the modified conventional Scherbius system by a 12 pulse converter in conjunction with a chopper at steady state and at dynamic conditions. A 220 W wound motor is employed for testing. It is found that the motor speed can be controlled to be constant in the operating range of 450-1200 rpm at no load and full load. It is also found that the efficiency of the proposed system is remarkably increased since the harmonics of the input ac line current is reduced while the ac line input power factor is increased. (author)

Fundamental limitations on 'warp drive' spacetimes

Energy Technology Data Exchange (ETDEWEB)

Lobo, Francisco S N [Centro de Astronomia e AstrofIsica da Universidade de Lisboa, Campo Grande, Ed. C8 1749-016 Lisbon (Portugal); Visser, Matt [School of Mathematical and Computing Sciences, Victoria University of Wellington, PO Box 600, Wellington (New Zealand)

2004-12-21

'Warp drive' spacetimes are useful as 'gedanken-experiments' that force us to confront the foundations of general relativity, and among other things, to precisely formulate the notion of 'superluminal' communication. After carefully formulating the Alcubierre and Natario warp drive spacetimes, and verifying their non-perturbative violation of the classical energy conditions, we consider a more modest question and apply linearized gravity to the weak-field warp drive, testing the energy conditions to first and second orders of the warp-bubble velocity, v. Since we take the warp-bubble velocity to be non-relativistic, v << c, we are not primarily interested in the 'superluminal' features of the warp drive. Instead we focus on a secondary feature of the warp drive that has not previously been remarked upon-the warp drive (if it could be built) would be an example of a 'reaction-less drive'. For both the Alcubierre and Natario warp drives we find that the occurrence of significant energy condition violations is not just a high-speed effect, but that the violations persist even at arbitrarily low speeds. A particularly interesting feature of this construction is that it is now meaningful to think of placing a finite mass spaceship at the centre of the warp bubble, and then see how the energy in the warp field compares with the mass-energy of the spaceship. There is no hope of doing this in Alcubierre's original version of the warp field, since by definition the point at the centre of the warp bubble moves on a geodesic and is 'massless'. That is, in Alcubierre's original formalism and in the Natario formalism the spaceship is always treated as a test particle, while in the linearized theory we can treat the spaceship as a finite mass object. For both the Alcubierre and Natario warp drives we find that even at low speeds the net (negative) energy stored in the warp fields must be a significant fraction

Belt drive construction improvement

Directory of Open Access Journals (Sweden)

I.Yu. Khomenko

2012-08-01

Full Text Available The possibility of the traction capacity increase of the belt drive TRK is examined. This was done for the purpose of air conditioning system of passenger car with double-generator system energy supplying. Belts XPC (made by the German firm «Continental ContiTech» testing were conducted. The results confirmed the possibility of their usage in order to improve belt drive TRK characteristics.

The Effects of Projected Future Demand Including Very Light Jet Air-Taxi Operations on U.S. National Airspace System Delays as a Function of Next Generation Air Transportation System Airspace Capacity

Science.gov (United States)

Smith, Jerry; Viken, Jeff; Dollyhigh, Samuel; Trani, Antonio; Baik, Hojong; Hinze, Nicholas; Ashiabor, Senanu

2007-01-01

This paper presents the results from a study which investigates the potential effects of the growth in air traffic demand including projected Very Light Jet (VLJ) air-taxi operations adding to delays experienced by commercial passenger air transportation in the year 2025. The geographic region studied is the contiguous United States (U.S.) of America, although international air traffic to and from the U.S. is included. The main focus of this paper is to determine how much air traffic growth, including VLJ air-taxi operations will add to enroute airspace congestion and determine what additional airspace capacity will be needed to accommodate the expected demand. Terminal airspace is not modeled and increased airport capacity is assumed.

Levy-taxis: a novel search strategy for finding odor plumes in turbulent flow-dominated environments

International Nuclear Information System (INIS)

Pasternak, Zohar; Grasso, Frank W; Bartumeus, Frederic

2009-01-01

Locating chemical plumes in aquatic or terrestrial environments is important for many economic, conservation, security and health related human activities. The localization process is composed mainly of two phases: finding the chemical plume and then tracking it to its source. Plume tracking has been the subject of considerable study whereas plume finding has received little attention. We address here the latter issue, where the searching agent must find the plume in a region often many times larger than the plume and devoid of the relevant chemical cues. The probability of detecting the plume not only depends on the movements of the searching agent but also on the fluid mechanical regime, shaping plume intermittency in space and time; this is a basic, general problem when exploring for ephemeral resources (e.g. moving and/or concealing targets). Here we present a bio-inspired search strategy named Levy-taxis that, under certain conditions, located odor plumes significantly faster and with a better success rate than other search strategies such as Levy walks (LW), correlated random walks (CRW) and systematic zig-zag. These results are based on computer simulations which contain, for the first time ever, digitalized real-world water flow and chemical plume instead of their theoretical model approximations. Combining elements of LW and CRW, Levy-taxis is particularly efficient for searching in flow-dominated environments: it adaptively controls the stochastic search pattern using environmental information (i.e. flow) that is available throughout the course of the search and shows correlation with the source providing the cues. This strategy finds natural application in real-world search missions, both by humans and autonomous robots, since it accommodates the stochastic nature of chemical mixing in turbulent flows. In addition, it may prove useful in the field of behavioral ecology, explaining and predicting the movement patterns of various animals searching for food

Levy-taxis: a novel search strategy for finding odor plumes in turbulent flow-dominated environments

Energy Technology Data Exchange (ETDEWEB)

Pasternak, Zohar; Grasso, Frank W [BioMimetic and Cognitive Robotics Laboratory, Department of Psychology, Brooklyn College, The City University of New York, 2900 Bedford Avenue, Brooklyn 11210, NY (United States); Bartumeus, Frederic [Department of Ecology and Evolutionary Biology and Princeton Environmental Institute, 106 Guyot Hall, Princeton University, Princeton 08544, NJ (United States)], E-mail: zpast@yahoo.com

2009-10-30

Locating chemical plumes in aquatic or terrestrial environments is important for many economic, conservation, security and health related human activities. The localization process is composed mainly of two phases: finding the chemical plume and then tracking it to its source. Plume tracking has been the subject of considerable study whereas plume finding has received little attention. We address here the latter issue, where the searching agent must find the plume in a region often many times larger than the plume and devoid of the relevant chemical cues. The probability of detecting the plume not only depends on the movements of the searching agent but also on the fluid mechanical regime, shaping plume intermittency in space and time; this is a basic, general problem when exploring for ephemeral resources (e.g. moving and/or concealing targets). Here we present a bio-inspired search strategy named Levy-taxis that, under certain conditions, located odor plumes significantly faster and with a better success rate than other search strategies such as Levy walks (LW), correlated random walks (CRW) and systematic zig-zag. These results are based on computer simulations which contain, for the first time ever, digitalized real-world water flow and chemical plume instead of their theoretical model approximations. Combining elements of LW and CRW, Levy-taxis is particularly efficient for searching in flow-dominated environments: it adaptively controls the stochastic search pattern using environmental information (i.e. flow) that is available throughout the course of the search and shows correlation with the source providing the cues. This strategy finds natural application in real-world search missions, both by humans and autonomous robots, since it accommodates the stochastic nature of chemical mixing in turbulent flows. In addition, it may prove useful in the field of behavioral ecology, explaining and predicting the movement patterns of various animals searching for food

Digital control of electric drives

CERN Document Server

Koziol, R; Szklarski, L

1992-01-01

The electromechanical systems employed in different branches of industry are utilized most often as drives of working machines which must be fed with electric energy in a continuous, periodic or even discrete way. Some of these machines operate at constant speed, others require wide and varying energy control. In many designs the synchronous cooperation of several electric drives is required in addition to the desired dynamic properties. For these reasons the control of the cooperation and dynamics of electromechanical systems requires the use of computers.This book adopts an unusual approach

Transportation Energy Futures Series: Effects of Travel Reduction and Efficient Driving on Transportation: Energy Use and Greenhouse Gas Emissions

Energy Technology Data Exchange (ETDEWEB)

Porter, C. D.; Brown, A.; DeFlorio, J.; McKenzie, E.; Tao, W.; Vimmerstedt, L.

2013-03-01

Since the 1970s, numerous transportation strategies have been formulated to change the behavior of drivers or travelers by reducing trips, shifting travel to more efficient modes, or improving the efficiency of existing modes. This report summarizes findings documented in existing literature to identify strategies with the greatest potential impact. The estimated effects of implementing the most significant and aggressive individual driver behavior modification strategies range from less than 1% to a few percent reduction in transportation energy use and GHG emissions. Combined strategies result in reductions of 7% to 15% by 2030. Pricing, ridesharing, eco-driving, and speed limit reduction/enforcement strategies are widely judged to have the greatest estimated potential effect, but lack the widespread public acceptance needed to accomplish maximum results. This is one of a series of reports produced as a result of the Transportation Energy Futures (TEF) project, a Department of Energy-sponsored multi-agency project initiated to pinpoint underexplored strategies for abating GHGs and reducing petroleum dependence related to transportation.

Transportation Energy Futures Series. Effects of Travel Reduction and Efficient Driving on Transportation. Energy Use and Greenhouse Gas Emissions

Energy Technology Data Exchange (ETDEWEB)

Porter, C. D. [National Renewable Energy Lab. (NREL) and Cambridge Systematics, Golden, CO (United States); Brown, A. [National Renewable Energy Lab. (NREL) and Cambridge Systematics, Golden, CO (United States); DeFlorio, J. [National Renewable Energy Lab. (NREL) and Cambridge Systematics, Golden, CO (United States); McKenzie, E. [National Renewable Energy Lab. (NREL) and Cambridge Systematics, Golden, CO (United States); Tao, W. [National Renewable Energy Lab. (NREL) and Cambridge Systematics, Golden, CO (United States); Vimmerstedt, L. [National Renewable Energy Lab. (NREL) and Cambridge Systematics, Golden, CO (United States)

2013-03-01

Since the 1970s, numerous transportation strategies have been formulated to change the behavior of drivers or travelers by reducing trips, shifting travel to more efficient modes, or improving the efficiency of existing modes. This report summarizes findings documented in existing literature to identify strategies with the greatest potential impact. The estimated effects of implementing the most significant and aggressive individual driver behavior modification strategies range from less than 1% to a few percent reduction in transportation energy use and GHG emissions. Combined strategies result in reductions of 7% to 15% by 2030. Pricing, ridesharing, eco-driving, and speed limit reduction/enforcement strategies are widely judged to have the greatest estimated potential effect, but lack the widespread public acceptance needed to accomplish maximum results. This is one of a series of reports produced as a result of the Transportation Energy Futures (TEF) project, a Department of Energy-sponsored multi-agency project initiated to pinpoint underexplored strategies for abating GHGs and reducing petroleum dependence related to transportation.

VEHICLE DRIVING CYCLE OPTIMISATION ON THE HIGHWAY

Directory of Open Access Journals (Sweden)

Zinoviy STOTSKO

2016-06-01

Full Text Available This paper is devoted to the problem of reducing vehicle energy consumption. The authors consider the optimisation of highway driving cycle a way to use the kinetic energy of a car more effectively at various road conditions. The model of a vehicle driving control at the highway which consists of elementary cycles, such as accelerating, free rolling and deceleration under forces of external resistance, was designed. Braking, as an energy dissipation regime, was not included. The influence of the various longitudinal profiles of the road was taken into consideration and included in the model. Ways to use the results of monitoring road and traffic conditions are presented. The method of non-linear programming is used to design the optimal vehicle control function and phase trajectory. The results are presented by improved typical driving cycles that present energy saving as a subject of choice at a specified schedule.

Loss minimization control and efficiency determination of electric drives in traction applications

Energy Technology Data Exchange (ETDEWEB)

Windisch, Thomas; Hofmann, Wilfried [Technische Univ. Dresden (Germany). Lehrstuhl fuer Elektrische Maschinen und Antriebe

2012-11-01

High-power electric drives in automotive traction applications consume a large part of the disposable electric energy. For this reason the energy efficiency of the drives is of great importance for range and fuel consumption of the hybrid electric vehicle. The paper describes two possible drives with different electric motors from a control point of view. The electric power losses in the drive system are determined depending on the operating point of the machine. With these loss characteristics the control of the drives is optimized to produce minimal losses. Finally the energy efficiency for a realistic urban bus drive cycle is calculated to compare the two types. (orig.)

Importance-Performance Analysis of Taxi Service Quality%客运出租汽车服务质量的重要度-绩效分析

Institute of Scientific and Technical Information of China (English)

姚志刚

2011-01-01

为了明确客运出租汽车服务质量管理的重点,根据SERVPERF模型将客运出租汽车服务质量划分为22个构成要素.以杭州市为例进行乘客调查,采用区间估计法计算各服务质量构成要素的重要度和绩效均值及其置信区间,建立服务质量的重要度-绩效分析四象限矩阵,在95％置信水平下从12个构成要素中获得客运出租汽车服务质量重点改善的5方面内容.结果表明,客运出租汽车服务质量管理应从提高车辆档次、外观和加强安全设施配置转向改善车内卫生、治理驾驶员拒载绕道和规范驾驶员行为；采用区间估计修正传统重要度-绩效分析法,可减少问卷调查的统计误差,使客运出租汽车服务质量评价结果更加可信.%To identify the key points of taxi service management, a SERVPERF instrument including 22 items is proposed to measure the taxi service quality. Scales of importance and performance of all items are obtained in a passenger survey in Hangzhou, China. Confidence intervals of means of those importance and performance are calculated with interval estimation and a four-quadrant matrix of importance-performance analysis is conducted. Five items of the priority task for taxi service management are obtained from 12 items at the 95% confidence level. The present study reveals that resources used for improving vehicle facilities and safety equipments should be reduced and be applied for vehicle interior cleanliness, driver' s refusal and detour, driver's rude behaviors and service consciousness. The result indicates that the revised importance-performance analysis with interval estimation is a reliable approach for measuring key factors of taxi service management.

Simulation of Induction Traction Drive with Supercapacitor Energy Storage System Test Bench

Directory of Open Access Journals (Sweden)

Stana Girts

2015-12-01

Full Text Available The paper describes the application of supercapacitor energy storage system for induction traction drive test bench that replaces a real electric public transport for performing testing and researches. The suitability and usage of such bench for research purposes is explained and the importance of the development of software mathematical model for performing simulations to be done before physical implementation measures is reasoned. The working principle of the bench and applied components are described. A virtual model of the bench was built and simulations were performed using Matlab/Simulink software. The basic topology of the virtual bench model is described as well. The calculations of this work show the scaling of supercapacitor energy storage system by setting different limits of working voltage range in order to adjust them to test bench parameters, whereas the modelling compares two simulation cases – the application of less supercapacitors and the application of more supercapacitors with the same common rated voltage. The autonomous mode simulations were also performed. Simulation results are analyzed and recommendations for the application of the supercapacitor energy storage system, with respect to initial supercapacitor circuit voltage, are given.

What Drives Saline Circulation Cells in Coastal Aquifers? An Energy Balance for Density-Driven Groundwater Systems

Science.gov (United States)

Harvey, C. F.; Michael, H. A.

2017-12-01

We formulate the energy balance for coastal groundwater systems and apply it to: (1) Explain the energy driving offshore saline circulation cells, and; (2) Assess the accuracy of numerical simulations of coastal groundwater systems. The flow of fresh groundwater to the ocean is driven by the loss of potential energy as groundwater drops from the elevation of the inland watertable, where recharge occurs, to discharge at sea level. This freshwater flow creates an underlying circulation cell of seawater, drawn into coastal aquifers offshore and discharging near shore, that adds to total submarine groundwater discharge. The saline water in the circulation cell enters and exits the aquifer through the sea floor at the same hydraulic potential. Existing theory explains that the saline circulation cell is driven by mixing of fresh and saline without any additional source of potential or mechanical power. This explanation raises a basic thermodynamic question: what is the source of energy that drives the saline circulation cell? Here, we resolve this question by building upon Hubbert's conception of hydraulic potential to formulate an energy balance for density-dependent flow and salt transport through an aquifer. We show that, because local energy dissipation within the aquifer is proportional to the square of the groundwater velocity, more groundwater flow may be driven through an aquifer for a given energy input if local variations in velocity are smoothed. Our numerical simulations of coastal groundwater systems show that dispersion of salt across the fresh-saline interface spreads flow over larger volumes of the aquifer, smoothing the velocity field, and increasing total flow and submarine groundwater discharge without consuming more power. The energy balance also provides a criterion, in addition to conventional mass balances, for judging the accuracy of numerical solutions of non-linear density-dependent flow problems. Our results show that some numerical

Determination of the energy of suprathermal electrons during lower hybrid current drive on PBX-M

International Nuclear Information System (INIS)

von Goeler, S.; Bernabei, S.; Davis, W.; Ignat, D.; Kaita, R.; Roney, P.; Stevens, J.; Post-Zwicker, A.

1993-06-01

Suprathermal electrons are diagnosed by a hard x-ray pinhole camera during lower hybrid current drive on PBX-M. The experimental hard x-ray images are compared with simulated images, which result from an integration of the relativistic bremsstrahlung along lines-of-sight through the bean-shaped plasma. Images with centrally peaked and radially hollow radiation profiles are easily distinguished. The energy distribution of the suprathermal electrons is analyzed by comparing images taken with different absorber foils. An effective photon temperature is derived from the experimental images, and a comparison with simulated photon temperatures yields the energy of the suprathermal electrons. The analysis indicates that the energy of the suprathermal electrons in the hollow discharges is in the 50 to 100 key range in the center of the discharge. There seems to exist a very small higher energy component close to the plasma edge

On Power Stream in Motor or Drive System

Directory of Open Access Journals (Sweden)

Paszota Zygmunt

2016-12-01

Full Text Available In a motor or a drive system the quantity of power increases in the direction opposite to the direction of power flow. Energy losses and energy efficiency of a motor or drive system must be presented as functions of physical quantities independent of losses. Such quantities are speed and load. But the picture of power stream in a motor or drive system is presented in the literature in the form of traditional Sankey diagram of power decrease in the direction of power flow. The paper refers to Matthew H. Sankey’s diagram in his paper „The Thermal Efficiency of Steam Engines“ of 1898. Presented is also a diagram of power increase in the direction opposite to the direction of power flow. The diagram, replacing the Sankey’s diagram, opens a new prospect for research into power of energy losses and efficiency of motors and drive systems.

Viability of using different types of main oil pipelines pump drives

Science.gov (United States)

Zakirzakov, A. G.; Zemenkov, Yu D.; Akulov, K. A.

2018-05-01

The choice of the pumping units' drive of main oil pipelines is of great importance both for design of pipelines and for modernization of existing ones. At the beginning of oil pipeline transport development, due to the limited number and types of energy sources, the choice was not difficult. The combustion energy of the pumped product was often the only available energy resource for its transportation. In this regard, the pipelines that had autonomous energy sources favorably differed from other energy consumers in the sector. With the passage of time, with the development of the country's electricity supply system, the electric drive for power-line equipment of oil pipelines becomes the dominant type of a pumping station drive. Nowadays, the traditional component is an essential factor when choosing some type of the drive. For many years, oil companies have been using electric drives for pumps, while gas transport enterprises prefer self-contained gas turbines.

Neutral beam current drive with balanced injection

International Nuclear Information System (INIS)

Eckhartt, D.

1990-01-01

Current drive with fast ions has proved its capability to sustain a tokamak plasma free of externally induced electric fields in a stationary state. The suprathermal ion population within the toroidal plasma was created by quasi-tangential and uni-directional injection of high-energy neutral atoms, their ionisation and subsequent deceleration by collisions with the background plasma particles. In future large tokamaks of the NET/INTER-type, with reactor-relevant values of plasma density and temperature, this current drive scheme is expected to maintain the toroidal current at the plasma centre, as current drive by lower hybrid waves will be restricted to the outer plasma regions owing to strong wave damping. Adequate penetration of the neutral atoms through the dense plasma requires particle energies of several hundred kilovolts per nucleon since beam absorption scales roughly with the ratio beam energy over density. The realisation of such high-energy high-power neutral beams, based on negative ion technology, is now under study. (author) 7 refs., 2 figs

Topology Comparison of Superconducting Generators for 10-MW Direct-Drive Wind Turbines: Cost of Energy Based

DEFF Research Database (Denmark)

Liu, Dong; Polinder, Henk; Abrahamsen, Asger Bech

2017-01-01

This paper aims at finding feasible electromagnetic designs of superconducting synchronous generators (SCSGs) for a 10-MW direct-drive wind turbine. Since a lower levelized cost of energy (LCoE) increases the feasibility of SCSGs in this application, 12 generator topologies are compared regarding...... their LCoE in a simplified form of levelized equipment cost of energy (LCoE$_{\\text{eq}}$). MgB$_2$ wires are employed in the field winding. Based on the current unit cost and critical current density capability of the MgB $_2$ wire at 20 K, the topologies with more iron have a much lower LCo...

Energy conversion efficiency of hybrid electric heavy-duty vehicles operating according to diverse drive cycles

Energy Technology Data Exchange (ETDEWEB)

Banjac, Titina [AVL-AST d.o.o., Trg Leona Stuklja 5, SI-2000 Maribor (Slovenia); Trenc, Ferdinand; Katrasnik, Tomaz [Faculty of Mechanical Engineering, Univ. of Ljubljana, Askerceva 6, SI-1000 Ljubljana (Slovenia)

2009-12-15

Energy consumption and exhaust emissions of hybrid electric vehicles (HEVs) strongly depend on the HEV topology, power ratios of their components and applied control strategy. Combined analytical and simulation approach was applied to analyze energy conversion efficiency of different HEV topologies. Analytical approach is based on the energy balance equations and considers all energy paths in the HEVs from the energy sources to the wheels and to other energy sinks. Simulation approach is based on a fast forward-facing simulation model for simulating parallel and series HEVs as well as for conventional internal combustion engine vehicles, and considers all components relevant for modeling energy conversion phenomena. Combined approach enables evaluation of energy losses on different energy paths and provides their impact on the fuel economy. It therefore enables identification of most suitable HEV topology and of most suitable power ratios of the components for targeted vehicle application, since it reveals and quantifies the mechanisms that could lead to improved energy conversion efficiency of particular HEV. The paper exposes characteristics of the test cycles that lead to improved energy conversion efficiency of HEVs. Mechanisms leading to improved fuel economy of parallel HEVs through drive-away and vehicle propulsion at low powertrain loads by electric motor are also analyzed. It was also shown that control strategies managing energy flow through electric storage devices significantly influence energy conversion efficiency of series HEVs. (author)

Energy analysis of control rod drive mechanism in HTR-10

International Nuclear Information System (INIS)

Bo Hanliang; Wu Yuanqiang

2000-01-01

This paper presents a theoretical model for the control rod drive mechanism for the 10 MW High Temperature Gas Cooled Reactor (HTR-10) and analyzes accidents which may occur in the drive mechanism, for example, chain break, coupling damage and other damage scenarios. The results show that the matching problem between buffer capability and coupling strength is the main reason for coupling damage; increased temperatures would reduce eddy damping and cause a mismatch between buffer capability and coupling strength; and the displacement of the buffer spring will affect the coupling force. The results provide a theoretical basis for the design of the control rod drive mechanism for HTR-10

Lévy-taxis: a novel search strategy for finding odor plumes in turbulent flow-dominated environments

Science.gov (United States)

Pasternak, Zohar; Bartumeus, Frederic; Grasso, Frank W.

2009-10-01

Locating chemical plumes in aquatic or terrestrial environments is important for many economic, conservation, security and health related human activities. The localization process is composed mainly of two phases: finding the chemical plume and then tracking it to its source. Plume tracking has been the subject of considerable study whereas plume finding has received little attention. We address here the latter issue, where the searching agent must find the plume in a region often many times larger than the plume and devoid of the relevant chemical cues. The probability of detecting the plume not only depends on the movements of the searching agent but also on the fluid mechanical regime, shaping plume intermittency in space and time; this is a basic, general problem when exploring for ephemeral resources (e.g. moving and/or concealing targets). Here we present a bio-inspired search strategy named Lévy-taxis that, under certain conditions, located odor plumes significantly faster and with a better success rate than other search strategies such as Lévy walks (LW), correlated random walks (CRW) and systematic zig-zag. These results are based on computer simulations which contain, for the first time ever, digitalized real-world water flow and chemical plume instead of their theoretical model approximations. Combining elements of LW and CRW, Lévy-taxis is particularly efficient for searching in flow-dominated environments: it adaptively controls the stochastic search pattern using environmental information (i.e. flow) that is available throughout the course of the search and shows correlation with the source providing the cues. This strategy finds natural application in real-world search missions, both by humans and autonomous robots, since it accomodates the stochastic nature of chemical mixing in turbulent flows. In addition, it may prove useful in the field of behavioral ecology, explaining and predicting the movement patterns of various animals searching for

Replacement of pneumatic and hydraulic drives with electrical drives - Analysis of potential; Ersatz von pneumatischen und hydraulischen Antrieben durch Elektroantriebe. Potentialanalyse

Energy Technology Data Exchange (ETDEWEB)

Berchten, S. [BEngineering, Bassersdorf (Switzerland); Ritz, Ch. [Schnyder Ingenieure AG, Steg (Switzerland)

2006-07-01

This final report for the Swiss Federal Office of Energy (SFOE) discusses the potential offered by modern technologies to save energy. The replacement of energy-intensive methods of providing physical movement - such as with pneumatic and hydraulic drives - with electrical drives is discussed. Based on existing installations in industry, an estimate of the potential for making savings is presented. This shows that large energy savings can be made by directly converting electrical into mechanical energy. Using real world examples, end-users and decision-makers are shown two profit-scenarios involving the purchase of a new system or retrofitting an existing system. The scenarios take investments, operating costs and system life-cycle into account. Extrapolations provide estimates of savings-potentials for the Swiss electricity market. Various market sectors are looked at, including the metal-working, chemical, foodstuffs and packaging sectors. Examples of installations actually implemented, where electro-mechanical systems have replaced pneumatic and hydraulic drives, are given.

The CLIC Multi-Drive Beam Scheme

CERN Document Server

Corsini, R

1998-01-01

The CLIC study of an e+ / e- linear collider in the TeV energy range is based on Two-Beam Acceleration (TBA) in which the RF power needed to accelerate the beam is extracted from high intensity relativistic electron beams, the so-called drive beams. The generation, acceleration and transport of the high-intensity drive beams in an efficient and reliable way constitute a challenging task. An overview of a potentially very effective scheme is presented. It is based on the generation of trains of short bunches, accelerated sequentially in low frequency superconducting cavities in a c.w. mode, stored in an isochronous ring and combined at high energy by funnelling before injection by sectors into the drive linac for RF power production. The various systems of the complex are discussed.

A performance study on a direct drive hydro turbine for wave energy converter

International Nuclear Information System (INIS)

Choi, Young Do; Kim, Chang Goo; Kim, You Taek; Lee, Young Ho; Song, Jung Il

2010-01-01

Clean and renewable energy technologies using ocean energy give us non-polluting alternatives to fossil-fueled power plants as a countermeasure against global warming and growing demand for electrical energy. Among the ocean energy resources, wave power takes a growing interest because of its enormous amount of potential energy in the world. Therefore, various types of wave power systems to capture the energy of ocean waves have been developed. However, a suitable turbine type is not yet normalized because of relatively low efficiency of the turbine systems. The purpose of this study is to investigate the performance of a newly developed direct drive hydro turbine (DDT), which will be built in a caisson for a wave power plant. Experiment and CFD analysis are conducted to clarify the turbine performance and internal flow characteristics. The results show that the DDT obtains fairly good turbine efficiency in cases with and without wave conditions. Most of the output power is generated at the runner passage of Stage 2. Relatively larger amount of the decreased tangential velocity at Stage 2 produces more angular momentum than that at Stage 1 and thus, the larger angular momentum at the Stage 2 makes a greater contribution to the generation of total output power in comparison with that at Stage 1. Large vortex existing in the upper-left region of the runner passage forms a large recirculation region in the runner passage, and the recirculating flow consumes the output power at Region 2

A performance study on a direct drive hydro turbine for wave energy converter

Energy Technology Data Exchange (ETDEWEB)

Choi, Young Do [Mokpo National University, Muan (Korea, Republic of); Kim, Chang Goo; Kim, You Taek; Lee, Young Ho [Korea Maritime University, Busan (Korea, Republic of); Song, Jung Il [Changwon National University, Changwon (Korea, Republic of)

2010-11-15

Clean and renewable energy technologies using ocean energy give us non-polluting alternatives to fossil-fueled power plants as a countermeasure against global warming and growing demand for electrical energy. Among the ocean energy resources, wave power takes a growing interest because of its enormous amount of potential energy in the world. Therefore, various types of wave power systems to capture the energy of ocean waves have been developed. However, a suitable turbine type is not yet normalized because of relatively low efficiency of the turbine systems. The purpose of this study is to investigate the performance of a newly developed direct drive hydro turbine (DDT), which will be built in a caisson for a wave power plant. Experiment and CFD analysis are conducted to clarify the turbine performance and internal flow characteristics. The results show that the DDT obtains fairly good turbine efficiency in cases with and without wave conditions. Most of the output power is generated at the runner passage of Stage 2. Relatively larger amount of the decreased tangential velocity at Stage 2 produces more angular momentum than that at Stage 1 and thus, the larger angular momentum at the Stage 2 makes a greater contribution to the generation of total output power in comparison with that at Stage 1. Large vortex existing in the upper-left region of the runner passage forms a large recirculation region in the runner passage, and the recirculating flow consumes the output power at Region 2

CLIC Drive Beam Position Monitor

CERN Document Server

Smith, S; Gudkov, D; Soby, L; Syratchev, I

2011-01-01

CLIC, an electron-positron linear collider proposed to probe the TeV energy scale, is based on a two-beam scheme where RF power to accelerate a high energy luminosity beam is extracted from a high current drive beam. The drive beam is efficiently generated in a long train at modest frequency and current then compressed in length and multiplied in frequency via bunch interleaving. The drive beam decelerator requires >40000 quadrupoles, each holding a beam position monitor (BPM). Though resolution requirements are modest (2 microns) these BPMs face several challenges. They must be compact and inexpensive. They must operate below waveguide cutoff to insure locality of position signals, ruling out processing at the natural 12 GHz bunch spacing frequency. Wakefields must be kept low. We find compact conventional stripline BPM with signals processed below 40 MHz can meet requirements. Choices of mechanical design, operating frequency, bandwidth, calibration and processing algorithm are presented. Calculations of wa...

Degradation of selected industrial dyes using Mg-doped TiO2 polyscales under natural sun light as an alternative driving energy

Science.gov (United States)

Shivaraju, H. P.; Midhun, G.; Anil Kumar, K. M.; Pallavi, S.; Pallavi, N.; Behzad, Shahmoradi

2017-11-01

Designing photocatalytic materials with modified functionalities for the utilization of renewable energy sources as an alternative driving energy has attracted much attention in the area of sustainable wastewater treatment applications. Catalyst-assisted advanced oxidation process is an emerging treatment technology for organic pollutants and toxicants in industrial wastewater. Preparation of visible-light-responsive photocatalyst such as Mg-doped TiO2 polyscales was carried out under mild sol-gel technique. Mg-doped TiO2 polyscales were characterized by powder XRD, SEM, FTIR, and optical and photocatalytic activity techniques. The Mg-doped TiO2 showed a mixed phase of anatase and rutile with an excellent crystallinity, structural elucidations, polyscales morphology, consequent shifting of bandgap energy and adequate photocatalytic activities under visible range of light. Mg-doped TiO2 polyscales were investigated for their efficiencies in the degradation of most commonly used industrial dyes in the real-time textile wastewater. Mg-doped TiO2 polyscales showed excellent photocatalytic degradation efficiency in both model industrial dyes (65-95%) and textile wastewater (92%) under natural sunlight as an alternative and renewable driving energy.

Efficiency trends in electric machines and drives

International Nuclear Information System (INIS)

Mecrow, B.C.; Jack, A.G.

2008-01-01

Almost all electricity in the UK is generated by rotating electrical generators, and approximately half of it is used to drive electrical motors. This means that efficiency improvements to electrical machines can have a very large impact on energy consumption. The key challenges to increased efficiency in systems driven by electrical machines lie in three areas: to extend the application of variable-speed electric drives into new areas through reduction of power electronic and control costs; to integrate the drive and the driven load to maximise system efficiency; and to increase the efficiency of the electrical drive itself. In the short to medium term, efficiency gains within electrical machines will result from the development of new materials and construction techniques. Approximately a quarter of new electrical machines are driven by variable-speed drives. These are a less mature product than electrical machines and should see larger efficiency gains over the next 50 years. Advances will occur, with new types of power electronic devices that reduce switching and conduction loss. With variable-speed drives, there is complete freedom to vary the speed of the driven load. Replacing fixed-speed machines with variable-speed drives for a high proportion of industrial loads could mean a 15-30% energy saving. This could save the UK 15 billion kWh of electricity per year which, when combined with motor and drive efficiency gains, would amount to a total annual saving of 24 billion kWh

Design of driving control strategy of torque distribution for two - wheel independent drive electric vehicle

Science.gov (United States)

Zhang, Chuanwei; Zhang, Dongsheng; Wen, Jianping

2018-02-01

In order to coordinately control the torque distribution of existing two-wheel independent drive electric vehicle, and improve the energy efficiency and control stability of the whole vehicle, the control strategies based on fuzzy control were designed which adopt the direct yaw moment control as the main line. For realizing the torque coordination simulation of the two-wheel independent drive vehicle, the vehicle model, motor model and tire model were built, including the vehicle 7 - DOF dynamics model, motion equation, torque equation. Finally, in the Carsim - Simulink joint simulation platform, the feasibility of the drive control strategy was verified.

Collective human mobility pattern from taxi trips in urban area

KAUST Repository

Peng, Chengbin

2012-04-18

We analyze the passengers\\' traffic pattern for 1.58 million taxi trips of Shanghai, China. By employing the non-negative matrix factorization and optimization methods, we find that, people travel on workdays mainly for three purposes: commuting between home and workplace, traveling from workplace to workplace, and others such as leisure activities. Therefore, traffic flow in one area or between any pair of locations can be approximated by a linear combination of three basis flows, corresponding to the three purposes respectively. We name the coefficients in the linear combination as traffic powers, each of which indicates the strength of each basis flow. The traffic powers on different days are typically different even for the same location, due to the uncertainty of the human motion. Therefore, we provide a probability distribution function for the relative deviation of the traffic power. This distribution function is in terms of a series of functions for normalized binomial distributions. It can be well explained by statistical theories and is verified by empirical data. These findings are applicable in predicting the road traffic, tracing the traffic pattern and diagnosing the traffic related abnormal events. These results can also be used to infer land uses of urban area quite parsimoniously. 2012 Peng et al.

Comparison of drive systems for pulsed synchronous machines - an overview

International Nuclear Information System (INIS)

Baumgart, G.E.; Boenig, H.J.

1986-01-01

Magnetically confined plasma fusion experiments require large pulses of energy to be delivered into coil systems. One of the most effective methods of generating these high energy pulses is to convert stored inertial energy into electrical energy. Large synchronous generators of both the vertical and horizontal shaft type have been successfully used for this purpose. As the pulsed energy is delivered to the load, the inertial energy of the rotor of the machine is changed into electrical energy, causing the rotor to slow down. A drive system is required to accelerate the generator from standstill to the maximum operating speed and between load pulses from a reduced operating speed to the maximum speed. There are several types of drive systems that can be used for this application. An overview of six candidate drive systems is presented and comparisons of cost, performance, efficiency and line effects for these systems are described

Comparison of drive systems for pulsed synchronous machines: an overview

International Nuclear Information System (INIS)

Baumgart, G.E.; Boenig, H.J.

1985-01-01

Magnetically confined plasma fusion experiments require large pulses of energy to be delivered into coil systems. One of the most effective methods of generating these high energy pulses is to convert stored inertial energy into electrical energy. Large synchronous generators of both the vertical and horizontal shaft type have been successfully used for this purpose. As the pulsed energy is delivered to the load, the inertial energy of the rotor of the machine is changed into electrical energy, causing the rotor to slow down. A drive system is required to accelerate the generator from standstill to the maximum operating speed and between load pulses from a reduced operating speed to the maximum speed. There are several types of drive systems that can be used for this application. An overview of six candidate drive systems is presented and comparisons of cost, performance, efficiency, and line effects for these systems are described

Analysis and optimization of indicators of energy and resource consumption of gas turbine and electric drives for transportation of hydrocarbons

Science.gov (United States)

Golik, V. V.; Zemenkova, M. Yu; Seroshtanov, I. V.; Begalko, Z. V.

2018-05-01

The paper presents the results of the analysis of statistical indicators of energy and resource consumption in oil and gas transportation by the example of one of the regions of Russia. The article analyzes engineering characteristics of compressor station drives. Official statistical bulletins on the fuel and energy resources of the region in the pipeline oil and gas transportation system were used as the initial data.

Driving forces for texture transformation in thin Ag films

International Nuclear Information System (INIS)

Ellis, Elizabeth A.; Chmielus, Markus; Lin, Ming-Tzer; Joress, Howie; Visser, Kyle; Woll, Arthur; Vinci, Richard P.; Brown, Walter L.; Baker, Shefford P.

2016-01-01

The well-known thickness-dependent (111)-to-(100) texture transformation in thin FCC films is usually attributed to a competition between interface and strain energies. In this model, thin films retain their (111) texture due to the lower energy of the (111) interface, while thick films transform to (100) due to the lower stiffness and thus strain energy of a (100) film. However, recent work has called this model into question, suggesting that neither the stress nor the interface energy play a dominant role in texture transformation. We investigated the driving forces involved in this transformation by using a bulge test apparatus to induce different stresses in thin Ag films under identical annealing conditions. In situ synchrotron XRD measurements show the change in texture during annealing, and reveal that applied stresses have no effect on the transformation. Stress analysis shows that differences in driving forces for texture transformation due to applied bulge pressure were significant (≈200 kJ/m 3 ), suggesting that a different, much larger driving force must be responsible. Reduction in defect energy has been proposed as an alternative. However, vacancy and dislocation densities must be exceptionally high to significantly exceed the strain energy and do not provide obvious orientation selection mechanisms. Nanotwins in reported densities are shown to provide greater driving force (≈1000 kJ/m 3 ) and may account for orientation selection. The large difference between the calculated strain and defect energies and the driving force for grain growth (21,100 kJ/m 3 ) casts doubt on the applicability of a simple thermodynamic model of texture transformation.

What drives renewable energy development?

International Nuclear Information System (INIS)

Alagappan, L.; Orans, R.; Woo, C.K.

2011-01-01

This viewpoint reviews renewable energy development in 14 markets that differ in market structure (restructured vs. not restructured), use of feed-in-tariff (FIT) (yes vs. no), transmission planning (anticipatory vs. reactive), and transmission interconnection cost allocated to a renewable generator (high vs. low). We find that market restructuring is not a primary driver of renewable energy development. Renewable generation has the highest percent of total installed capacity in markets that use a FIT, employ anticipatory transmission planning, and have loads or end-users paying for most, if not all, of the transmission interconnection costs. In contrast, renewable developers have been less successful in markets that do not use a FIT, employ reactive transmission planning, and have generators paying for most, if not all, of the transmission interconnection costs. While these policies can lead to higher penetration of renewable energy in the short run, their high cost to ratepayers can threaten the economic sustainability of renewable energy in the long-run. - Highlights: → Market structure seems to have little effect on renewable energy development. → Renewable energy development is more successful in markets that use a FIT. → Anticipatory transmission planning aids renewable energy development. → Low interconnection costs for developers also aids renewable energy development.

Optimal Control Development System for Electrical Drives

Directory of Open Access Journals (Sweden)

Marian GAICEANU

2008-08-01

Full Text Available In this paper the optimal electrical drive development system is presented. It consists of both electrical drive types: DC and AC. In order to implement the optimal control for AC drive system an Altivar 71 inverter, a Frato magnetic particle brake (as load, three-phase induction machine, and dSpace 1104 controller have been used. The on-line solution of the matrix Riccati differential equation (MRDE is computed by dSpace 1104 controller, based on the corresponding feedback signals, generating the optimal speed reference for the AC drive system. The optimal speed reference is tracked by Altivar 71 inverter, conducting to energy reduction in AC drive. The classical control (consisting of rotor field oriented control with PI controllers and the optimal one have been implemented by designing an adequate ControlDesk interface. The three-phase induction machine (IM is controlled at constant flux. Therefore, the linear dynamic mathematical model of the IM has been obtained. The optimal control law provides transient regimes with minimal energy consumption. The obtained solution by integration of the MRDE is orientated towards the numerical implementation-by using a zero order hold. The development system is very useful for researchers, doctoral students or experts training in electrical drive. The experimental results are shown.

Beyond barriers – A case study on driving forces for improved energy efficiency in the foundry industries in Finland, France, Germany, Italy, Poland, Spain, and Sweden

International Nuclear Information System (INIS)

Thollander, Patrik; Backlund, Sandra; Trianni, Andrea; Cagno, Enrico

2013-01-01

Highlights: • Results are based on a questionnaire in the European foundry industry. • The energy efficiency potential is assed to be 7.5% of the total energy use. • Most important drivers to and barriers for energy efficiency are financial followed by organizational. • EPC is used among 23% of the foundries, third party financing among 12%. • Large energy management improvement potentials are uncovered. - Abstract: Energy management plays an important role in the transformation of industrial energy systems towards improved energy efficiency and increased sustainability. This paper aims to study driving forces for improved energy efficiency in some European energy-intensive foundry industries. The investigation has been conducted as a multiple case study involving 65 foundries located in Finland, France, Germany, Italy, Poland, Spain, and Sweden. The most relevant perceived driving forces were found to be financially related, followed by organizational driving forces. Nevertheless, some differences can be appreciated according to the firm’s size and country. Almost half of the studied foundries lack a long-term energy strategy, about one-fourth stated that they have used Energy Performance Contracting (EPC), and only approximately one in ten foundries have used Third Party Financing (TPF). Among the studied foundries, three out of five have conducted an energy audit. On average, the energy saving potential according to the respondents is stated to be 7.5%. In conclusion, energy management in the European foundry industry, despite increasing energy prices and extensive energy policy actions taken by the EU, still seems to have great improvement potential, calling for future research and policy actions in the field

Modelling the Effect of Driving Events on Electrical Vehicle Energy Consumption Using Inertial Sensors in Smartphones

Directory of Open Access Journals (Sweden)

David Jiménez

2018-02-01

Full Text Available Air pollution and climate change are some of the main problems that humankind is currently facing. The electrification of the transport sector will help to reduce these problems, but one of the major barriers for the massive adoption of electric vehicles is their limited range. The energy consumption in these vehicles is affected, among other variables, by the driving behavior, making range a value that must be personalized to each driver and each type of electric vehicle. In this paper we offer a way to estimate a personalized energy consumption model by the use of the vehicle dynamics and the driving events detected by the use of the smartphone inertial sensors, allowing an easy and non-intrusive manner to predict the correct range for each user. This paper proposes, for the classification of events, a deep neural network (Long-Short Time Memory which has been trained with more than 22,000 car trips, and the application to improve the consumption model taking into account the driver behavior captured across different trips, allowing a personalized prediction. Results and validation in real cases show that errors in the predicted consumption values are halved when abrupt events are considered in the model.

Building America FY 2016 Annual Report: Building America Is Driving Real Solutions in the Race to Zero Energy Homes -- Appendix

Energy Technology Data Exchange (ETDEWEB)

Sara Farrar, Stacey Rothgeb, Ben Polly, Lieko Earle, Tim Merrigan

2017-01-01

This document is a set of appendices presenting technical discussion and references as a companion to the 'Building America FY 2016 Annual Report: Building America Is Driving Real Solutions in the Race to Zero Energy Homes' publication.

First Observation of Cross-Beam Energy Transfer Mitigation for Direct-Drive Inertial Confinement Fusion Implosions Using Wavelength Detuning at the National Ignition Facility.

Science.gov (United States)

Marozas, J A; Hohenberger, M; Rosenberg, M J; Turnbull, D; Collins, T J B; Radha, P B; McKenty, P W; Zuegel, J D; Marshall, F J; Regan, S P; Sangster, T C; Seka, W; Campbell, E M; Goncharov, V N; Bowers, M W; Di Nicola, J-M G; Erbert, G; MacGowan, B J; Pelz, L J; Yang, S T

2018-02-23

Cross-beam energy transfer (CBET) results from two-beam energy exchange via seeded stimulated Brillouin scattering, which detrimentally reduces ablation pressure and implosion velocity in direct-drive inertial confinement fusion. Mitigating CBET is demonstrated for the first time in inertial-confinement implosions at the National Ignition Facility by detuning the laser-source wavelengths (±2.3  Å UV) of the interacting beams. We show that, in polar direct-drive, wavelength detuning increases the equatorial region velocity experimentally by 16% and alters the in-flight shell morphology. These experimental observations are consistent with design predictions of radiation-hydrodynamic simulations that indicate a 10% increase in the average ablation pressure.

Energy and exergy analysis of the turbo-generators and steam turbine for the main feed water pump drive on LNG carrier

International Nuclear Information System (INIS)

Mrzljak, Vedran; Poljak, Igor; Mrakovčić, Tomislav

2017-01-01

Highlights: • Two low-power steam turbines in the LNG carrier propulsion plant were investigated. • Energy and exergy efficiencies of both steam turbines vary between 46% and 62%. • The ambient temperature has a low impact on exergy efficiency of analyzed turbines. • The maximum efficiencies area of both turbines was investigated. • A method for increasing the turbo-generator efficiencies by 1–3% is presented. - Abstract: Nowadays, marine propulsion systems are mainly based on internal combustion diesel engines. Despite this fact, a number of LNG carriers have steam propulsion plants. In such plants, steam turbines are used not only for ship propulsion, but also for electrical power generation and main feed water pump drive. Marine turbo-generators and steam turbine for the main feed water pump drive were investigated on the analyzed LNG carrier with steam propulsion plant. The measurements of various operating parameters were performed and obtained data were used for energy and exergy analysis. All the measurements and calculations were performed during the ship acceleration. The analysis shows that the energy and exergy efficiencies of both analyzed low-power turbines vary between 46% and 62% what is significantly lower in comparison with the high-power steam turbines. The ambient temperature has a low impact on exergy efficiency of analyzed turbines (change in ambient temperature for 10 °C causes less than 1% change in exergy efficiency). The highest exergy efficiencies were achieved at the lowest observed ambient temperature. Also, the highest efficiencies were achieved at 71.5% of maximum developed turbo-generator power while the highest efficiencies of steam turbine for the main feed water pump drive were achieved at maximum turbine developed power. Replacing the existing steam turbine for the main feed water pump drive with an electric motor would increase the turbo-generator energy and exergy efficiencies for at least 1–3% in all analyzed

Semiclassical instability of warp drives

Energy Technology Data Exchange (ETDEWEB)

Barcelo, C [Instituto de Astrofisica de Andalucia, IAA-CSIC, Glorieta de la Astronomia s/n, 18008 Granada (Spain); Finazzi, S; Liberati, S, E-mail: carlos@iaa.e, E-mail: finazzi@sissa.i, E-mail: liberati@sissa.i

2010-05-01

Warp drives, at least theoretically, provide a way to travel at superluminal speeds. However, even if one succeeded in providing the necessary exotic matter to construct them, it would still be necessary to check whether they would survive to the switching on of quantum effects. In this contribution we will report on the behaviour of the Renormalized Stress-Energy Tensor (RSET) in the spacetimes associated with superluminal warp drives. We find that the RSET will exponentially grow in time close to the front wall of the superluminal bubble, hence strongly supporting the conclusion that the warp-drive geometries are unstable against semiclassical back-reaction.

USING OF NON-CONVENTIONAL FUELS IN HYBRID VEHICLE DRIVES

Directory of Open Access Journals (Sweden)

Dalibor Barta

2016-12-01

Full Text Available Electric or hybrid vehicles are becoming increasingly common on roads. While electric vehicles are still more or less intended for city traffic, hybrid vehicles allow normal use due to wider driving range. The use of internal combustion engines in hybrid drives is still an inspiration to find the way to reduce the produc-tion of emissions. Numbers of alternative energy resources were studied as a substitution of conventional fuels for hybrid vehicles drives worldwide. The paper deals with the possibility of using alternative fuels as CNG, LPG and LNG in combination with hybrid drive of a midibus with the capacity of 20 passengers. Various aspects and techniques of hybrid vehicles from energy management system, propulsion system and using of various alternative fuels are explored in this paper. Other related fields of hybrid vehicles such as changes of vehicle weight or influence of electric energy sources on the total vehicle emission production are also included.

Meeting the challenges of the new energy industry: The driving forces facing electric power generators and the natural gas industry

International Nuclear Information System (INIS)

Anon.

1995-01-01

The proceedings of the IGT national conference on meeting the challenges of the New Energy Industry: The driving forces facing Electric Power Generators and the Natural Gas Industry are presented. The conference was held June 19-21, 1995 at the Ambassador West Hotel in Downtown Chicago, Illinois. A separate abstract and indexing for each of the 18 papers presented for inclusion in the Energy Science and Technology Database

Meeting the challenges of the new energy industry: The driving forces facing electric power generators and the natural gas industry

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-12-31

The proceedings of the IGT national conference on meeting the challenges of the New Energy Industry: The driving forces facing Electric Power Generators and the Natural Gas Industry are presented. The conference was held June 19-21, 1995 at the Ambassador West Hotel in Downtown Chicago, Illinois. A separate abstract and indexing for each of the 18 papers presented for inclusion in the Energy Science and Technology Database.

Toyota hybrid synergy drive

Energy Technology Data Exchange (ETDEWEB)

Gautschi, H.

2008-07-01

This presentation made at the Swiss 2008 research conference on traffic by Hannes Gautschi, director of service and training at the Toyota company in Switzerland, takes a look at Toyota's hybrid drive vehicles. The construction of the vehicles and their combined combustion engines and electric generators and drives is presented and the combined operation of these components is described. Braking and energy recovery are discussed. Figures on the performance, fuel consumption and CO{sub 2} output of the hybrid vehicles are compared with those of conventional vehicles.

On the Optimally Controlled Hydrostatic Mechanical Drive in Case of Flywheel Acceleration

Directory of Open Access Journals (Sweden)

V. A. Korsunskii

2016-01-01

Full Text Available An improving dynamic quality of vehicles and enhanced fuel efficiency are gained thanks to the combined power system (CPS, comprising a main energy source - internal combustion engine (ICE with an attained level of the power source - and an auxiliary energy source, i.e. an energy storage device (a flywheel.To solve this problem was developed a mathematical model of CPS comprising internal combustion engine and flywheel energy storage (FES with stepless drive.The stepless drive of the flywheel is made to be hydrostatic mechanical to raise the system efficiency. To reduce the drive weight and simplify the control system in the hydraulic part of the flywheel drive is used only one hydraulic unit being controlled.The paper presents a kinematic diagram of the track-type vehicle equipped with the CPS that has a hydrostatic mechanical drive of the flywheel and a mechanical transmission.A mathematical model of the system comprising an ICE, hydrostatic mechanical drive, and FES with stepless drive has been developed. This mathematical model was used to study the influence of ICE and flywheel drive parameters on the dynamic characteristics of the system.The paper estimates the impact of flywheel energy consumption, pressure in the hydraulic system, and control parameter of hydrostatic mechanical drive on the charging time of FES.The obtained piecewise linear law to control the regulation parameter of the hydraulic unit allows us to minimize the charging time of the flywheel at the short-term stops and in the parking area of a tracked vehicle equipped with a CPS.The causes affecting the performance of ‘ICE – drive – flywheel’ system in the course of the flywheel acceleration are a restricted maximum power of the engine, as well as a limited generating capacity, and a maximum flywheel drive hydro-system pressure.The obtained results allow us to determine rational parameters of the flywheel and the laws of drive control to provide their further

How energy conversion drives economic growth far from the equilibrium of neoclassical economics

International Nuclear Information System (INIS)

Kümmel, Reiner; Lindenberger, Dietmar

2014-01-01

Energy conversion in the machines and information processors of the capital stock drives the growth of modern economies. This is exemplified for Germany, Japan, and the USA during the second half of the 20th century: econometric analyses reveal that the output elasticity, i.e. the economic weight, of energy is much larger than energy's share in total factor cost, while for labor just the opposite is true. This is at variance with mainstream economic theory according to which an economy should operate in the neoclassical equilibrium, where output elasticities equal factor cost shares. The standard derivation of the neoclassical equilibrium from the maximization of profit or of time-integrated utility disregards technological constraints. We show that the inclusion of these constraints in our nonlinear-optimization calculus results in equilibrium conditions, where generalized shadow prices destroy the equality of output elasticities and cost shares. Consequently, at the prices of capital, labor, and energy we have known so far, industrial economies have evolved far from the neoclassical equilibrium. This is illustrated by the example of the German industrial sector evolving on the mountain of factor costs before and during the first and the second oil price explosion. It indicates the influence of the ‘virtually binding’ technological constraints on entrepreneurial decisions, and the existence of ‘soft constraints’ as well. Implications for employment and future economic growth are discussed. (paper)

How energy conversion drives economic growth far from the equilibrium of neoclassical economics

Science.gov (United States)

Kümmel, Reiner; Lindenberger, Dietmar

2014-12-01

Energy conversion in the machines and information processors of the capital stock drives the growth of modern economies. This is exemplified for Germany, Japan, and the USA during the second half of the 20th century: econometric analyses reveal that the output elasticity, i.e. the economic weight, of energy is much larger than energy's share in total factor cost, while for labor just the opposite is true. This is at variance with mainstream economic theory according to which an economy should operate in the neoclassical equilibrium, where output elasticities equal factor cost shares. The standard derivation of the neoclassical equilibrium from the maximization of profit or of time-integrated utility disregards technological constraints. We show that the inclusion of these constraints in our nonlinear-optimization calculus results in equilibrium conditions, where generalized shadow prices destroy the equality of output elasticities and cost shares. Consequently, at the prices of capital, labor, and energy we have known so far, industrial economies have evolved far from the neoclassical equilibrium. This is illustrated by the example of the German industrial sector evolving on the mountain of factor costs before and during the first and the second oil price explosion. It indicates the influence of the ‘virtually binding’ technological constraints on entrepreneurial decisions, and the existence of ‘soft constraints’ as well. Implications for employment and future economic growth are discussed.

Power and momentum relations in rotating magnetic field current drive

Energy Technology Data Exchange (ETDEWEB)

Hugrass, W N [Flinders Univ. of South Australia, Bedford Park. School of Physical Sciences

1984-01-01

The use of rotating magnetic fields (RMF) to drive steady currents in plasmas involves a transfer of energy and angular momentum from the radio frequency source feeding the rotating field coils to the plasma. The power-torque relationships in RMF systems are discussed and the analogy between RMF current drive and the polyphase induction motor is explained. The general relationship between the energy and angular momentum transfer is utilized to calculate the efficiency of the RMF plasma current drive. It is found that relatively high efficiencies can be achieved in RMF current drive because of the low phase velocity and small slip between the rotating field and the electron fluid.

Driving Extreme Efficiency to Market

Science.gov (United States)

Garbesi, Karina

2014-03-01

The rapid development of extremely energy efficient appliances and equipment is essential to curtail catastrophic climate disruption. This will require the on-going development of products that apply all best-practices and that take advantage of the synergies of hybridization and building integration. Beyond that, it requires the development of new disruptive technologies and concepts. To facilitate these goals, in 2011 the Lawrence Berkeley National Laboratory and the U.S. Department of Energy launched the Max Tech and Beyond Design Competition for Ultra-Low-Energy-Use Appliances and Equipment. Now in its third year, the competition supports faculty-lead student design teams at U.S. universities to develop and test new technology prototypes. This talk describes what the competition and the Max Tech Program are doing to drive such rapid technology progress and to facilitate the entry to the market of successful Max Tech prototypes. The talk also initiates a discussion of physicists' unique role in driving that technology progress faster and farther. Emerging Technologies, Building Technologies Office, U.S. Department of Energy.

Energy management in vehicles with alternative drives; Energiemanagement in Fahrzeugen mit alternativen Antrieben

Energy Technology Data Exchange (ETDEWEB)

Lange, S.; Schimanski, M.

2007-11-21

Within the next few years, the automotive industry will be confronted with many challenges, as for example stricter emission standards and increasing oil prices. To meet the challenges, alternative drive concepts are currently being developed and placed in the market. To ensure a secure and efficient operation of the electric components, the introduction of an integrated energy management is required. It comprises all planning, controlling and predictive measures. The first part of this dissertation presents a new system concept, which can make an online prognosis of expected driving situations, such as speed and altitude profiles by means of internal vehicle information during an operating cycle. Based on this the control strategy can calculate the future power requirement of the vehicle and initiate control commands to enable a more efficient driving. The basis of this system concept is the recognition of routes with characteristic steering angle information and the creation of a history database for the routes driven with the respective vehicle speeds and altitudes. On the basis of an extensive analysis of the vehicle's electrical system in the second part of the dissertation, different effects on the development process for dimensioning the electrical system power supply are discussed. From this follows the necessity to develop a tool chain based on simulations. The tool chain consists of commercial simulation tools and the software Avanti (Advanced Analysis Tool and Simulation Interface) which is developed within the scope of the dissertation. Avanti enables an automated and optimal procedure when dimensioning the vehicle's electrical system in consideration of different control algorithms. A substantial part of this tool chain is the integration of a verified VHDL-AMS model library for the electrical system components. (orig.)

Energy management in vehicles with alternative drives; Energiemanagement in Fahrzeugen mit alternativen Antrieben

Energy Technology Data Exchange (ETDEWEB)

Lange, S; Schimanski, M

2007-11-21

Within the next few years, the automotive industry will be confronted with many challenges, as for example stricter emission standards and increasing oil prices. To meet the challenges, alternative drive concepts are currently being developed and placed in the market. To ensure a secure and efficient operation of the electric components, the introduction of an integrated energy management is required. It comprises all planning, controlling and predictive measures. The first part of this dissertation presents a new system concept, which can make an online prognosis of expected driving situations, such as speed and altitude profiles by means of internal vehicle information during an operating cycle. Based on this the control strategy can calculate the future power requirement of the vehicle and initiate control commands to enable a more efficient driving. The basis of this system concept is the recognition of routes with characteristic steering angle information and the creation of a history database for the routes driven with the respective vehicle speeds and altitudes. On the basis of an extensive analysis of the vehicle's electrical system in the second part of the dissertation, different effects on the development process for dimensioning the electrical system power supply are discussed. From this follows the necessity to develop a tool chain based on simulations. The tool chain consists of commercial simulation tools and the software Avanti (Advanced Analysis Tool and Simulation Interface) which is developed within the scope of the dissertation. Avanti enables an automated and optimal procedure when dimensioning the vehicle's electrical system in consideration of different control algorithms. A substantial part of this tool chain is the integration of a verified VHDL-AMS model library for the electrical system components. (orig.)

Novel control algorithm of braking energy regeneration system for an electric vehicle during safety–critical driving maneuvers

International Nuclear Information System (INIS)

Lv, Chen; Zhang, Junzhi; Li, Yutong; Yuan, Ye

2015-01-01

Highlights: • Models of an electric vehicle with regenerative braking system (RBS) are built. • Control algorithm of RBS under safety–critical driving maneuvers is proposed. • Simulations and HIL tests of the proposed strategy are conducted. • Performance improvement of vehicle’s mean deceleration is up to 13.89%. • Test results verify the feasibility and effectiveness of the proposed method. - Abstract: This paper mainly focuses on control algorithm of the braking energy regeneration system of an electric bus under safety–critical driving situations. With the aims of guaranteeing vehicle stability in various types of tyre–road adhesion conditions, based on the characteristics of electrified powertrain, a novel control algorithm of regenerative braking system is proposed for electric vehicles during anti-lock braking procedures. First, the models of vehicle dynamics and main components including braking energy regenerative system of the case-study electric bus are built in MATLAB/Simulink. Then, based on the phase-plane method, the optimal brake torque is calculated for ABS control of vehicle. Next, a novel allocation strategy, wherein the target optimal brake torque is divided into two parts that are handled separately by the regenerative and friction brakes, is developed. Simulations of the proposed control strategy are conducted based on system models built using MATLAB/Simulink. The simulation results demonstrate that the developed strategy enables improved control in terms of vehicle stability and braking performance under different emergency driving conditions. To further verify the synthesized control algorithm, hardware-in-the-loop tests are also performed. The experimental results validate the simulation data and verify the feasibility and effectiveness of the developed control algorithm.

Implications of driving patterns on well-to-wheel performance of plug-in hybrid electric vehicles.

Science.gov (United States)

Raykin, Leon; MacLean, Heather L; Roorda, Matthew J

2012-06-05

This study examines how driving patterns (distance and conditions) and the electricity generation supply interact to impact well-to-wheel (WTW) energy use and greenhouse gas (GHG) emissions of plug-in hybrid electric vehicles (PHEVs). The WTW performance of a PHEV is compared with that of a similar (nonplug-in) gasoline hybrid electric vehicle and internal combustion engine vehicle (ICEV). Driving PHEVs for short distances between recharging generally results in lower WTW total and fossil energy use and GHG emissions per kilometer compared to driving long distances, but the extent of the reductions depends on the electricity supply. For example, the shortest driving pattern in this study with hydroelectricity uses 81% less fossil energy than the longest driving pattern. However, the shortest driving pattern with coal-based electricity uses only 28% less fossil energy. Similar trends are observed in reductions relative to the nonplug-in vehicles. Irrespective of the electricity supply, PHEVs result in greater reductions in WTW energy use and GHG emissions relative to ICEVs for city than highway driving conditions. PHEVs charging from coal facilities only reduce WTW energy use and GHG emissions relative to ICEVs for certain favorable driving conditions. The study results have implications for environmentally beneficial PHEV adoption and usage patterns.

Impact Of Real-World Driving Characteristics On Vehicular Emissions

OpenAIRE

Nesamani, K S; Subramanian, K. P.

2005-01-01

With increase in traffic volume and change in travel related characteristics, vehicular emissions and energy consumption have increased significantly since two decades in India. Current models are not capable of estimating vehicular emissions accurately due to inadequate representation of real-world driving. The focus of this paper is to understand the level of Indian Driving cycle (IDC) in representing the real-world driving and to assess the impact of real-world driving on vehicular emissio...

Driving forces: Motor vehicle trends and their implications for global warming, energy strategies, and transportation planning

International Nuclear Information System (INIS)

MacKenzie, J.J.; Walsh, M.P.

1990-01-01

Cars, trucks, and other vehicles have long been linked to smog and other urban pollution, but the part they play in the larger complex of atmospheric and energy ills that we now face is often overlooked. In Driving Forces: Motor Vehicle Trends and Their Implications for Global Warming, Energy Strategies, and Transportation Planning, James J. MacKenzie, senior associate in World Resources Institute's Program in Climate, Energy, and Pollution, and Michael P. Walsh, an international consultant on transportation and environmental issues, fill in this knowledge gap with new data and analyses. They spell out four policy shifts that can help hold the line on global warming: improve new-vehicle efficiency; make transportation more efficient; cut other greenhouse gas emissions; create the green car of the future. The report focuses especially on the US, which pioneered the automotive revolution and leads the world in oil imports and emissions

Deformation-induced martensitic transformation in a 201 austenitic steel: The synergy of stacking fault energy and chemical driving force

Energy Technology Data Exchange (ETDEWEB)

Moallemi, M., E-mail: m.moallemi@ma.iut.ac.ir [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Kermanpur, A. [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Najafizadeh, A. [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of); Fould Institute of Technology, Fouladshahr, Isfahan, 8491663763 (Iran, Islamic Republic of); Rezaee, A.; Baghbadorani, H. Samaei; Nezhadfar, P. Dastranjy [Department of Materials Engineering, Isfahan University of Technology, Isfahan 84156-83111 (Iran, Islamic Republic of)

2016-01-20

The present study deals with the correlation of stacking fault energy's synergy and driving force in the formation of deformation-induced martensitic transformation in a 201 austenitic stainless steel. The fraction of deformation-induced martensite was characterized by means of X-ray diffraction and magnetic induction techniques. The kinetics of the martensite formation versus applied strain was evaluated through the sigmoidal model. It was shown that the volume fraction of ά-martensite is closely related to the driving force/SFE ratio of the alloy. The results also showed that the martensite content is similar in both XRD and magnetic methods and the applied sigmoidal model was consistent with the obtained experimental data.

Direct Drive Wave Energy Buoy

Energy Technology Data Exchange (ETDEWEB)

Rhinefrank, Kenneth [Columbia Power Technologies, Inc., Charlottesville, VA (United States); Lamb, Bradford [Columbia Power Technologies, Inc., Charlottesville, VA (United States); Prudell, Joseph [Columbia Power Technologies, Inc., Charlottesville, VA (United States); Hammagren, Erik [Columbia Power Technologies, Inc., Charlottesville, VA (United States); Lenee-Bluhm, Pukha [Columbia Power Technologies, Inc., Charlottesville, VA (United States)

2016-08-22

This Project aims to satisfy objectives of the DOE’s Water Power Program by completing a system detailed design (SDD) and other important activities in the first phase of a utility-scale grid-connected ocean wave energy demonstration. In early 2012, Columbia Power (CPwr) had determined that further cost and performance optimization was necessary in order to commercialize its StingRAY wave energy converter (WEC). CPwr’s progress toward commercialization, and the requisite technology development path, were focused on transitioning toward a commercial-scale demonstration. This path required significant investment to be successful, and the justification for this investment required improved annual energy production (AEP) and lower capital costs. Engineering solutions were developed to address these technical and cost challenges, incorporated into a proposal to the US Department of Energy (DOE), and then adapted to form the technical content and statement of project objectives of the resulting Project (DE-EE0005930). Through Project cost-sharing and technical collaboration between DOE and CPwr, and technical collaboration with Oregon State University (OSU), National Renewable Energy Lab (NREL) and other Project partners, we have demonstrated experimentally that these conceptual improvements have merit and made significant progress towards a certified WEC system design at a selected and contracted deployment site at the Wave Energy Test Site (WETS) at the Marine Corps Base in Oahu, HI (MCBH).

The question of drive vs. motive in psychoanalysis: a modest proposal.

Science.gov (United States)

Meissner, W W

2009-08-01

This essay explores the possibility of an alternative hypothesis to the prevailing psychoanalytic instinctual drive theory whose theoretical and clinical validity has been variously critiqued and challenged. Arguments are suggested in support of the concept of motive as a viable alternative theory to the drive theory and as a replacement for the traditional instinctual drive model. Issues discussed include the understanding of the mind-body relation, the meaning of psychic determinism and overdetermination, the opposition of drive vs. motive (and the related distinction of cause vs. motive), the meaning of psychic energy, and the difference between the concept of drives as the source of all mental energy and the concept of personal agency. The discussion concludes with some observations on the clinical implications of these concepts.

Assessing Patient bypass Behavior Using Taxi Trip Origin–Destination (OD Data

Directory of Open Access Journals (Sweden)

Gege Yang

2016-09-01

Full Text Available Many patients prefer to use the best hospitals even if there are one or more other hospitals closer to their homes; this behavior is called “hospital bypass behavior”. Because this behavior can be problematic in urban areas, it is important that it be reduced. In this paper, the taxi GPS data of Beijing and Suzhou were used to measure hospital bypass behavior. The “bypass behavior index” (BBI represents the bypass behavior for each hospital. The results indicated that the mean hospital bypass trip distance value ranges from 5.988 km to 9.754 km in Beijing and from 4.168 km to 10.283 km in Suzhou. In general, the bypass shares of both areas show a gradually increasing trend. The following hospitals exhibited significant patient bypass behavior: the 301 Hospital, Beijing Children’s Hospital, the Second Affiliated Hospital of Soochow University and the Suzhou Hospital of Traditional Chinese Medicine. The hospitals’ reputation, transport accessibility and spatial distribution were found to be the main factors affecting patient bypass behavior. Although the hospital bypass phenomena generally appeared to be more pronounced in Beijing, the bypass trip distances between hospitals were found to be more significant in Suzhou.

Polar-Drive Experiments at the National Ignition Facility

Science.gov (United States)

Hohenberger, M.

2014-10-01

To support direct-drive inertial confinement fusion (ICF) experiments at the National Ignition Facility (NIF) in its indirect-drive beam configuration, the polar-drive (PD) concept has been proposed. It requires direct-drive-specific beam smoothing, phase plates, and repointing the NIF beams toward the equator to ensure symmetric target irradiation. First experiments testing the performance of ignition-relevant PD implosions at the NIF have been performed. The goal of these early experiments was to develop a stable, warm implosion platform to investigate laser deposition and laser-plasma instabilities at ignition-relevant plasma conditions, and to develop and validate ignition-relevant models of laser deposition and heat conduction. These experiments utilize the NIF in its current configuration, including beam geometry, phase plates, and beam smoothing. Warm, 2.2-mm-diam plastic shells were imploded with total drive energies ranging from ~ 350 to 750 kJ with peak powers of 60 to 180 TW and peak on-target intensities from 4 ×1014 to 1 . 2 ×1015 W/cm2. Results from these initial experiments are presented, including the level of hot-electron preheat, and implosion symmetry and shell trajectory inferred via self-emission imaging and backlighting. Experiments are simulated with the 2-D hydrodynamics code DRACO including a full 3-D ray trace to model oblique beams, and a model for cross-beam energy transfer (CBET). These simulations indicate that CBET affects the shell symmetry and leads to a loss of energy imparted onto the shell, consistent with the experimental data. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

A Mobile, Dynamic, and Privacy-Preserving Matching System for Car and Taxi Pools

Directory of Open Access Journals (Sweden)

Shin-Yan Chiou

2014-01-01

Full Text Available Recently, rates of vehicle ownership have risen globally, exacerbating problems including air pollution, lack of parking, and traffic congestion. While many solutions to these problems have been proposed, carpooling remains one of the most effective approaches. Recently, several carpooling platforms have been built on cloud computing systems, with originators posting online list of departure/arrival points and schedules from which participants can search for rides that match their needs. However, it can be difficult to make matches quickly and the systems are subject to privacy concerns in that they may disclose private information such as names, registration data, and departure/arrival schedules. This paper proposes a dynamic matching method for car/taxi pools for use in mobile devices via ad hoc Wi-Fi networks. The proposed method also preserves user privacy including names and departure/arrival schedules. Moreover, the system does not require the user to register any personal data, so such data cannot be leaked. The system was implemented on the Android mobile platform, allowing users to immediately and securely access the system via their smart phones.

Rise of oil prices and energy policy

International Nuclear Information System (INIS)

2005-01-01

This document reprints the talk of the press conference given by D. de Villepin, French prime minister, on August 16, 2005 about the alarming rise of oil prices. In his talk, the prime minister explains the reasons of the crisis (increase of worldwide consumption, political tensions in the Middle East..) and presents the strategy and main trends of the French energy policy: re-launching of energy investments in petroleum refining capacities and in the nuclear domain (new generation of power plants), development of renewable energy sources and in particular biofuels, re-launching of the energy saving policy thanks to financial incentives and to the development of clean vehicles and mass transportation systems. In a second part, the prime minister presents his policy of retro-cession of petroleum tax profits to low income workers, and of charge abatement to professionals having an occupation strongly penalized by the rise of oil prices (truckers, farmers, fishermen, taxi drivers). (J.S.)

Impact of Different Driving Cycles and Operating Conditions on CO2 Emissions and Energy Management Strategies of a Euro-6 Hybrid Electric Vehicle

Directory of Open Access Journals (Sweden)

Claudio Cubito

2017-10-01

Full Text Available Although Hybrid Electric Vehicles (HEVs represent one of the key technologies to reduce CO2 emissions, their effective potential in real world driving conditions strongly depends on the performance of their Energy Management System (EMS and on its capability to maximize the efficiency of the powertrain in real life as well as during Type Approval (TA tests. Attempting to close the gap between TA and real world CO2 emissions, the European Commission has decided to introduce from September 2017 the Worldwide Harmonized Light duty Test Procedure (WLTP, replacing the previous procedure based on the New European Driving Cycle (NEDC. The aim of this work is the analysis of the impact of different driving cycles and operating conditions on CO2 emissions and on energy management strategies of a Euro-6 HEV through the limited number of information available from the chassis dyno tests. The vehicle was tested considering different initial battery State of Charge (SOC, ranging from 40% to 65%, and engine coolant temperatures, from −7 °C to 70 °C. The change of test conditions from NEDC to WLTP was shown to lead to a significant reduction of the electric drive and to about a 30% increase of CO2 emissions. However, since the specific energy demand of WLTP is about 50% higher than that of NEDC, these results demonstrate that the EMS strategies of the tested vehicle can achieve, in test conditions closer to real life, even higher efficiency levels than those that are currently evaluated on the NEDC, and prove the effectiveness of HEV technology to reduce CO2 emissions.

Prospects for Off-axis Current Drive via High Field Side Lower Hybrid Current Drive in DIII-D

Science.gov (United States)

Wukitch, S. J.; Shiraiwa, S.; Wallace, G. M.; Bonoli, P. T.; Holcomb, C.; Park, J. M.; Pinsker, R. I.

2017-10-01

An outstanding challenge for an economical, steady state tokamak is efficient off-axis current drive scalable to reactors. Previous studies have focused on high field side (HFS) launch of lower hybrid waves for current drive (LHCD) in double null configurations in reactor grade plasmas. The goal of this work is to find a HFS LHCD scenario for DIII-D that balances coupling, power penetration and damping. The higher magnetic field on the HFS improves wave accessibility, which allows for lower n||waves to be launched. These waves penetrate farther into the plasma core before damping at higher Te yielding a higher current drive efficiency. Utilizing advanced ray tracing and Fokker Planck simulation tools (GENRAY+CQL3D), wave penetration, absorption and drive current profiles in high performance DIII-D H-Mode plasmas were investigated. We found LH scenarios with single pass absorption, excellent wave penetration to r/a 0.6-0.8, FWHM r/a=0.2 and driven current up to 0.37 MA/MW coupled. These simulations indicate that HFS LHCD has potential to achieve efficient off-axis current drive in DIII-D and the latest results will be presented. Work supported by U.S. Dept. of Energy, Office of Science, Office of Fusion Energy Sciences, using User Facility DIII-D, under Award No. DE-FC02-04ER54698 and Contract No. DE-FC02-01ER54648 under Scientific Discovery through Advanced Computing Initiative.

Quantum effects in warp drives

Directory of Open Access Journals (Sweden)

Finazzi Stefano

2013-09-01

Full Text Available Warp drives are interesting configurations that, at least theoretically, provide a way to travel at superluminal speed. Unfortunately, several issues seem to forbid their realization. First, a huge amount of exotic matter is required to build them. Second, the presence of quantum fields propagating in superluminal warp-drive geometries makes them semiclassically unstable. Indeed, a Hawking-like high-temperature flux of particles is generated inside the warp-drive bubble, which causes an exponential growth of the energy density measured at the front wall of the bubble by freely falling observers. Moreover, superluminal warp drives remain unstable even if the Lorentz symmetry is broken by the introduction of regulating higher order terms in the Lagrangian of the quantum field. If the dispersion relation of the quantum field is subluminal, a black-hole laser phenomenon yields an exponential amplification of the emitted flux. If it is superluminal, infrared effects cause a linear growth of this flux.

Fast wave current drive in reactor scale tokamaks

International Nuclear Information System (INIS)

Moreau, D.

1992-01-01

The IAEA Technical Committee Meeting on Fast Wave Current Drive in Reactor Scale Tokamaks, hosted by the Commissariat a l'Energie Atomique (CEA), Departement de Recherches sur la Fusion Controlee (Centres d'Etudes de Cadarache, under the Euratom-CEA Association for fusion) aimed at discussing the physics and the efficiency of non-inductive current drive by fast waves. Relevance to reactor size tokamaks and comparison between theory and experiment were emphasized. The following topics are described in the summary report: (i) theory and modelling of radiofrequency current drive (theory, full wave modelling, ray tracing and Fokker-Planck calculations, helicity injection and ponderomotive effects, and alternative radio-frequency current drive effects), (ii) present experiments, (iii) reactor applications (reactor scenarios including fast wave current drive; and fast wave current drive antennas); (iv) discussion and summary. 32 refs

Extended driving impairs nocturnal driving performances.

Directory of Open Access Journals (Sweden)

Patricia Sagaspe

Full Text Available Though fatigue and sleepiness at the wheel are well-known risk factors for traffic accidents, many drivers combine extended driving and sleep deprivation. Fatigue-related accidents occur mainly at night but there is no experimental data available to determine if the duration of prior driving affects driving performance at night. Participants drove in 3 nocturnal driving sessions (3-5 am, 1-5 am and 9 pm-5 am on open highway. Fourteen young healthy men (mean age [+/-SD] = 23.4 [+/-1.7] years participated Inappropriate line crossings (ILC in the last hour of driving of each session, sleep variables, self-perceived fatigue and sleepiness were measured. Compared to the short (3-5 am driving session, the incidence rate ratio of inappropriate line crossings increased by 2.6 (95% CI, 1.1 to 6.0; P<.05 for the intermediate (1-5 am driving session and by 4.0 (CI, 1.7 to 9.4; P<.001 for the long (9 pm-5 am driving session. Compared to the reference session (9-10 pm, the incidence rate ratio of inappropriate line crossings were 6.0 (95% CI, 2.3 to 15.5; P<.001, 15.4 (CI, 4.6 to 51.5; P<.001 and 24.3 (CI, 7.4 to 79.5; P<.001, respectively, for the three different durations of driving. Self-rated fatigue and sleepiness scores were both positively correlated to driving impairment in the intermediate and long duration sessions (P<.05 and increased significantly during the nocturnal driving sessions compared to the reference session (P<.01. At night, extended driving impairs driving performances and therefore should be limited.

Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT) |

Science.gov (United States)

Transportation Research | NREL Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT) Computer-Aided Engineering for Electric-Drive Vehicle Batteries (CAEBAT) Graphic of a 24-cell (bottom). Images: Courtesy of EC Power NREL's work on the U.S. Department of Energy Computer-Aided

Comparative analysis of energy economy among different types of electric motor driving; Analise comparativa de economia de energia entre diferentes tipos de acionamento de motores electricos

Energy Technology Data Exchange (ETDEWEB)

Silva, Marcelo Santos da; Oliveira, Carlos Henrique, e-mails: mcelo_sant@ig.com.br; caique1979@yahoo.com.br; Albuquerque, Carlos Jesivan Marques; Fortes, Marcio Zamboti [Universidade Severino Sombra (USS), Vassouras, RJ (Brazil)], e-mails: cjesivan@uss.br; mzamboti@uss.br

2008-07-01

The application of controlled drives loads of small power can cause undesirable disturbances for electrical installations, but it brings some benefits when comparing the energy consumption that this application has on its regular period of operation. This study analyses using comparatives, the electrical economy using the different types of drives for three phase electric induction motors of low voltage. Running up tests on the test bench didactic, the inverter drives, soft starter and contactor switch were analyzed for different loads (motor without load, 50% and 100% load), rating in S1 and S4. (author)

Alternative drives for motor cars. Hybrid systems, fuel cells, alternative energy sources. 2. enl. ed.; Alternative Antriebe fuer Automobile. Hybridsysteme, Brennstoffzellen, alternative Energietraeger

Energy Technology Data Exchange (ETDEWEB)

Stan, Cornel [Berkeley Univ., CA (United States)]|[Paris Univ. (France)]|[Pisa Univ. (Italy)]|[Perugia Univ. (Italy)]|[Westsaechsischen Hochschule Zwickau (Germany)

2008-07-01

The implementation possibilities of future drive concepts - from hybrid systems comprising an electric motor and an internal combustion engine to fuel cells to alternative fuels like hydrogen or alcohol - will depend largely on quality criteria, e.g. power density, rotary momentum, acceleration characteristics, specific energy consumption, emissions of chemical substances, and noise. The boundary criteria for the introduction of realizeable concepts of alternative drives for motor cars will be defined by the availability and storability of the envisaged fuels, technical complexity, cost, safety, infrastructure and service. The book presents and analyzes the processes, drives and energy sources that can be combined in complex energy management systems for motor cars in accordance with the aforementioned criteria. Knowledge about these facts is indispensable for the development of new concepts. The 2nd edition describes many new developments in car propulsion systems as well as their combinations, new energy sources, energy converters and energy stores. All contents and literature reflect the latest state of science and technology. (orig.) [German] Ueber die Realisierungsmoeglichkeiten zukuenftiger Antriebskonzepte - von Hybridsystemen Elektro-/Verbrennungsmotor ueber Brennstoffzellen bis zu alternativen Energietraegern wie Wasserstoff oder Alkohol - werden fundierte Kriterien der Qualitaet eines Antriebs entscheiden. Leistungsdichte, Drehmomentverlauf, Beschleunigungscharakteristik, spezifischer Energieverbrauch sowie Emission chemischer Stoffe und Geraeusche sind dafuer wichtige Merkmale zur Qualitaetsbeurteilung. Die Verfuegbarkeit und die Speicherfaehigkeit vorgesehener Energietraeger, die technische Komplexitaet, Kosten, Sicherheit, Infrastruktur und Service werden die Randbedingungen fuer die Einfuehrung realisierbarer Konzepte alternativer Antriebe fuer Automobile stellen. Die Uebersicht und die Analyse der Prozesse, Antriebsmaschinen und Energietraeger, die

Using variable speed drives technology to reap rewards of efficient HVAC design

International Nuclear Information System (INIS)

Anon.

1999-01-01

Electric motors are continuously running at full speed with vanes and throttles used to modulate the output, in most HVAC applications. This results in an excessive wastage of electrical energy, and the solution is the variable speed drive, which can save vast amounts of energy in fans, pumps and compressors across the HVAC system. Users of traditional control methods will not benefit from the energy savings that are possible through variable speed drives because the motor speed remains the same, with the result that some, and in some cases most, of the energy drawn will be wasted. Variable speed drives are more efficient because they control output by regulating the motor speed, rather than run the motor at full speed and use restrictions to reduce the flow. Recently, small so-called micro-drives have been launched, cutting the cost for most variable speed operation. Variable speed motors can also introduce new features to the HVAC system. An example of how drives can save money and improve the indoor climate is cited for Heathrow airport. There, the gateroom was earlier controlled by modulating valves in both heater and cooler coils, with two fans that operated continuously at rated speed. This system was very inefficient because the occupancy of the gateroom varied between zero and maximum several times daily. A new system was installed using two AC drives, in which one drive controls the supply air fan and the other the return air fan. The energy savings amounted to 89% during two tests and 77% in a third. A pump installation in the district heating system of Strasbourg, Germany, showed the savings that are possible in pump applications

Wavelength Detuning Cross-Beam Energy Transfer Mitigation Scheme for Direct-Drive: Modeling and Evidence from National Ignition Facility Implosions

Science.gov (United States)

Marozas, J. A.

2017-10-01

Cross-beam energy transfer (CBET) has been shown to significantly reduce the laser absorption and implosion speed in direct-drive implosion experiments on OMEGA and the National Ignition Facility (NIF). Mitigating CBET assists in achieving ignition-relevant hot-spot pressures in deuterium-tritium cryogenic OMEGA implosions. In addition, reducing CBET permits lower, more hydrodynamically stable, in-flight aspect ratio ignition designs with smaller nonuniformity growth during the acceleration phase. Detuning the wavelengths of the crossing beams is one of several techniques under investigation at the University of Rochester to mitigate CBET. This talk will describe these techniques with an emphasis on wavelength detuning. Recent experiments designed and predicted using multidimensional hydrodynamic simulations including CBET on the NIF have exploited the wavelength arrangement of the NIF beam geometry to demonstrate CBET mitigation through wavelength detuning in polar-direct-drive (PDD) implosions. Shapes and trajectories inferred from time-resolved x-ray radiography of the imploding shell, scattered-light spectra, and hard x-ray spectra generated by suprathermal electrons all indicate a reduction in CBET. These results and their implications for direct-drive ignition will be presented and discussed. In addition, hydrodynamically scaled ignition-relevant designs for OMEGA implosions exploiting wavelength detuning will be presented. Changes required to the OMEGA laser to permit wavelength detuning will be discussed. Future plans for PDD on the NIF including more-uniform implosions with CBET mitigation will be explored. This material is based upon work supported by the Department of Energy National Nuclear Security Administration under Award Number DE-NA0001944.

Design and Experiment Analysis of a Direct-Drive Wave Energy Converter with a Linear Generator

Directory of Open Access Journals (Sweden)

Jing Zhang

2018-03-01

Full Text Available Coastal waves are an abundant nonpolluting and renewable energy source. A wave energy converter (WEC must be designed for efficient and steady operation in highly energetic ocean environments. A direct-drive wave energy conversion (D-DWEC system with a tubular permanent magnet linear generator (TPMLG on a wind and solar photovoltaic complementary energy generation platform is proposed to improve the conversion efficiency and reduce the complexity and device volume of WECs. The operating principle of D-DWECs is introduced, and detailed analyses of the proposed D-DWEC’s floater system, wave force characteristics, and conversion efficiency conducted using computational fluid dynamics are presented. A TPMLG with an asymmetric slot structure is designed to increase the output electric power, and detailed analyses of the magnetic field distribution, detent force characteristics, and no-load and load performances conducted using finite element analysis are discussed. The TPMLG with an asymmetric slot, which produces the same power as the TPMLG with a symmetric slot, has one fifth detent force of the latter. An experiment system with a prototype of the TPMLG with a symmetric slot is used to test the simulation results. The experiment and analysis results agree well. Therefore, the proposed D-DWEC fulfills the requirements of WEC systems.

Speed Controlled Belt Conveyors: Drives and Mechanical Considerations

Directory of Open Access Journals (Sweden)

BEBIC, M. Z.

2018-02-01

Full Text Available The paper presents variable speed belt conveyor system where the reference speed is changed in order to achieve improved energy efficiency of operation. The recorded measurements show that belt tension varies within the same limits as under constant speed operation. These results introduce a new insight of the present state of the art in variable speed belt conveyor drives. The system is realized with remote control from the control center on an open pit mine. The structure of the multi-motor drive system of a single conveyor, as well as of the network-based control system distributed among belt conveyor stations and the control center are shown. Speed control of a belt conveyor system is organized to provide better utilization of the available material cross section on the belt and reduced electrical energy consumption of the drive. The experimental results obtained on the system prove that, under existing constraints, the applied algorithm has not introduced additional stress to the belt or mechanical assemblies during acceleration and deceleration processes, while providing higher energy efficiency of operation.

Forces that Drive Nanoscale Self-assembly on Solid Surfaces

International Nuclear Information System (INIS)

Suo, Z.; Lu, W.

2000-01-01

Experimental evidence has accumulated in the recent decade that nanoscale patterns can self-assemble on solid surfaces. A two-component monolayer grown on a solid surface may separate into distinct phases. Sometimes the phases select sizes about 10 nm, and order into an array of stripes or disks. This paper reviews a model that accounts for these behaviors. Attention is focused on thermodynamic forces that drive the self-assembly. A double-welled, composition-dependent free energy drives phase separation. The phase boundary energy drives phase coarsening. The concentration-dependent surface stress drives phase refining. It is the competition between the coarsening and the refining that leads to size selection and spatial ordering. These thermodynamic forces are embodied in a nonlinear diffusion equation. Numerical simulations reveal rich dynamics of the pattern formation process. It is relatively fast for the phases to separate and select a uniform size, but exceedingly slow to order over a long distance, unless the symmetry is suitably broken

High efficiency cabin air filter in vehicles reduces drivers' roadway particulate matter exposures and associated lipid peroxidation.

Science.gov (United States)

Yu, Nu; Shu, Shi; Lin, Yan; She, Jianwen; Ip, Ho Sai Simon; Qiu, Xinghua; Zhu, Yifang

2017-01-01

Commuters who spend long hours on roads are exposed to high levels of traffic related air pollutants (TRAPs). Despite some well-known multiple adverse effects of TRAPs on human health, limited studies have focused on mitigation strategies to reduce these effects. In this study, we measured fine particulate matter (PM2.5) and ultrafine particle (UFP) concentrations inside and outside 17 taxis simultaneously while they were driven on roadways. The drivers' urinary monohydroxylated polycyclic aromatic hydrocarbons (OH-PAHs) and malondialdehyde (MDA) concentrations just before and right after the driving tests were also determined. Data were collected under three driving conditions (i.e. no mitigation (NM), window closed (WC), and window closed plus using high efficiency cabin air filters (WC+HECA)) for each taxi and driver. The results show that, compared to NM, the WC+HECA reduced in-cabin PM2.5 and UFP concentrations, by 37% and 47% respectively (p health.

Drive beam stabilisation in the CLIC Test Facility 3

Science.gov (United States)

Malina, L.; Corsini, R.; Persson, T.; Skowroński, P. K.; Adli, E.

2018-06-01

The proposed Compact Linear Collider (CLIC) uses a high intensity, low energy drive beam to produce the RF power needed to accelerate a lower intensity main beam with 100 MV/m gradient. This scheme puts stringent requirements on drive beam stability in terms of phase, energy and current. The consequent experimental work was carried out in CLIC Test Facility CTF3. In this paper, we present a novel analysis technique in accelerator physics to find beam drifts and their sources in the vast amount of the continuously gathered signals. The instability sources are identified and adequately mitigated either by hardware improvements or by implementation and commissioning of various feedbacks, mostly beam-based. The resulting drive beam stability is of 0.2°@ 3 GHz in phase, 0.08% in relative beam energy and about 0.2% beam current. Finally, we propose a stabilisation concept for CLIC to guarantee the main beam stability.

Lower hybrid current drive in tokamak plasmas

International Nuclear Information System (INIS)

Ushigusa, Kenkichi

1999-03-01

Past ten years progress on Lower Hybrid Current Drive (LHCD) experiments have demonstrated the largest non-inductive current (3.6 MA, JT-60U), the longest current sustainment (2 hours, TRIAM-1M), non-inductive current drive at the highest density (n-bar e - 10 20 m -3 , ALCATOR-C) and the highest current drive efficiency (η CD = 3.5x10 19 m -2 A/W, JT-60). These results indicate that LHCD is one of the most promising methods to drive non-inductive current in the present tokamak plasmas. This paper presents recent experimental results on LHCD experiments. Basic theories of LH waves, the wave propagation and the current drive are briefly summarized. The main part of this paper describes several important results and their physical pictures on recent LHCD experiments; 1) the experimental set-up, 2) the current drive efficiency, 3) the control of current profile and MHD activities, 4) the global energy confinement, 5) the global power flow, 6) fast electron behavior, 7) interaction between LH waves and thermal/fast ions, 8) combination with other CD method. (author)

Electric and pneumatic drives in an exact comparison; Elektrische und pneumatische Antriebe im exakten Vergleich

Energy Technology Data Exchange (ETDEWEB)

Volk, Roland [Festo AG und Co. KG, Esslingen (Germany)

2013-04-01

The question, whether a pneumatic drive is more energy efficient than an electric drive, is very difficult to answer straightaway. In the automation technology, the energy efficiency always depends on the respective industrial application. Only the direct comparison of an electric and pneumatic drive having the same dimension in different conceptual formulations clears up with prejudices.

Glaucoma and Driving: On-Road Driving Characteristics

Science.gov (United States)

Wood, Joanne M.; Black, Alex A.; Mallon, Kerry; Thomas, Ravi; Owsley, Cynthia

2016-01-01

Purpose To comprehensively investigate the types of driving errors and locations that are most problematic for older drivers with glaucoma compared to those without glaucoma using a standardized on-road assessment. Methods Participants included 75 drivers with glaucoma (mean = 73.2±6.0 years) with mild to moderate field loss (better-eye MD = -1.21 dB; worse-eye MD = -7.75 dB) and 70 age-matched controls without glaucoma (mean = 72.6 ± 5.0 years). On-road driving performance was assessed in a dual-brake vehicle by an occupational therapist using a standardized scoring system which assessed the types of driving errors and the locations where they were made and the number of critical errors that required an instructor intervention. Driving safety was rated on a 10-point scale. Self-reported driving ability and difficulties were recorded using the Driving Habits Questionnaire. Results Drivers with glaucoma were rated as significantly less safe, made more driving errors, and had almost double the rate of critical errors than those without glaucoma. Driving errors involved lane positioning and planning/approach, and were significantly more likely to occur at traffic lights and yield/give-way intersections. There were few between group differences in self-reported driving ability. Conclusions Older drivers with glaucoma with even mild to moderate field loss exhibit impairments in driving ability, particularly during complex driving situations that involve tactical problems with lane-position, planning ahead and observation. These results, together with the fact that these drivers self-report their driving to be relatively good, reinforce the need for evidence-based on-road assessments for evaluating driving fitness. PMID:27472221

Glaucoma and Driving: On-Road Driving Characteristics.

Directory of Open Access Journals (Sweden)

Joanne M Wood

Full Text Available To comprehensively investigate the types of driving errors and locations that are most problematic for older drivers with glaucoma compared to those without glaucoma using a standardized on-road assessment.Participants included 75 drivers with glaucoma (mean = 73.2±6.0 years with mild to moderate field loss (better-eye MD = -1.21 dB; worse-eye MD = -7.75 dB and 70 age-matched controls without glaucoma (mean = 72.6 ± 5.0 years. On-road driving performance was assessed in a dual-brake vehicle by an occupational therapist using a standardized scoring system which assessed the types of driving errors and the locations where they were made and the number of critical errors that required an instructor intervention. Driving safety was rated on a 10-point scale. Self-reported driving ability and difficulties were recorded using the Driving Habits Questionnaire.Drivers with glaucoma were rated as significantly less safe, made more driving errors, and had almost double the rate of critical errors than those without glaucoma. Driving errors involved lane positioning and planning/approach, and were significantly more likely to occur at traffic lights and yield/give-way intersections. There were few between group differences in self-reported driving ability.Older drivers with glaucoma with even mild to moderate field loss exhibit impairments in driving ability, particularly during complex driving situations that involve tactical problems with lane-position, planning ahead and observation. These results, together with the fact that these drivers self-report their driving to be relatively good, reinforce the need for evidence-based on-road assessments for evaluating driving fitness.

Glaucoma and Driving: On-Road Driving Characteristics.

Science.gov (United States)

Wood, Joanne M; Black, Alex A; Mallon, Kerry; Thomas, Ravi; Owsley, Cynthia

2016-01-01

To comprehensively investigate the types of driving errors and locations that are most problematic for older drivers with glaucoma compared to those without glaucoma using a standardized on-road assessment. Participants included 75 drivers with glaucoma (mean = 73.2±6.0 years) with mild to moderate field loss (better-eye MD = -1.21 dB; worse-eye MD = -7.75 dB) and 70 age-matched controls without glaucoma (mean = 72.6 ± 5.0 years). On-road driving performance was assessed in a dual-brake vehicle by an occupational therapist using a standardized scoring system which assessed the types of driving errors and the locations where they were made and the number of critical errors that required an instructor intervention. Driving safety was rated on a 10-point scale. Self-reported driving ability and difficulties were recorded using the Driving Habits Questionnaire. Drivers with glaucoma were rated as significantly less safe, made more driving errors, and had almost double the rate of critical errors than those without glaucoma. Driving errors involved lane positioning and planning/approach, and were significantly more likely to occur at traffic lights and yield/give-way intersections. There were few between group differences in self-reported driving ability. Older drivers with glaucoma with even mild to moderate field loss exhibit impairments in driving ability, particularly during complex driving situations that involve tactical problems with lane-position, planning ahead and observation. These results, together with the fact that these drivers self-report their driving to be relatively good, reinforce the need for evidence-based on-road assessments for evaluating driving fitness.

Naturalistic drive cycle synthesis for pickup trucks.

Science.gov (United States)

Liu, Zifan; Ivanco, Andrej; Filipi, Zoran

2015-09-01

Future pick-up trucks are meeting much stricter fuel economy and exhaust emission standards. Design tradeoffs will have to be carefully evaluated to satisfy consumer expectations within the regulatory and cost constraints. Boundary conditions will obviously be critical for decision making: thus, the understanding of how customers are driving in naturalistic settings is indispensable. Federal driving schedules, while critical for certification, do not capture the richness of naturalistic cycles, particularly the aggressive maneuvers that often shape consumer perception of performance. While there are databases with large number of drive cycles, applying all of them directly in the design process is impractical. Therefore, representative drive cycles that capture the essence of the naturalistic driving should be synthesized from naturalistic driving data. Naturalistic drive cycles are firstly categorized by investigating their micro-trip components, defined as driving activities between successive stops. Micro-trips are expected to characterize underlying local traffic conditions, and separate different driving patterns. Next, the transitions from one vehicle state to another vehicle state in each cycle category are captured with Transition Probability Matrix (TPM). Candidate drive cycles can subsequently be synthesized using Markov Chain based on TPMs for each category. Finally, representative synthetic drive cycles are selected through assessment of significant cycle metrics to identify the ones with smallest errors. This paper provides a framework for synthesis of representative drive cycles from naturalistic driving data, which can subsequently be used for efficient optimization of design or control of pick-up truck powertrains. Manufacturers will benefit from representative drive cycles in several aspects, including quick assessments of vehicle performance and energy consumption in simulations, component sizing and design, optimization of control strategies, and

The effects of driving cessation on the elderly with dementia and their caregivers.

Science.gov (United States)

Taylor, B D; Tripodes, S

2001-07-01

This research explores how the loss of driving privileges by impaired drivers affects households. The particular focus is on the travel behavior and preceptions of people living in households where an elderly driver has had his or her license revoked due to Alzheimer's disease or a related dementia. The data for this analysis were drawn from a 1996 survey of households in California which queried the caregivers of people with dementia on how the former drivers access necessary destinations once they can no longer drive, and on the difficulties faced by other household members in seeking alternative means of transportation. After losing their license, the vast majority of people surveyed depended on informal support systems for transportation, such as rides from family and friends. Although such arrangements were not reported to be a problem for the majority of households, certain groups of non-drivers reported difficulty accessing services, particularly social and recreational destinations. The most commonly reported problem was a lack of available licensed drivers to chauffeur non-drivers. Importantly, no increase was observed in the number of people walking, using public transit, taxis, or van services following license revocation. People who did not live with at least one licensed driver and those who were younger and healthier reported the greatest mismatch between their need and desire to travel and the availability of transportation. In addition, some caregivers reported that they frequently missed work or stopped working entirely in order to care for and chauffeur people in the former drivers' household. Overall, these findings reinforce the importance of both developing transportation policies to support the functioning of informal transportation structures and in improving the range of alternative transportation options for those individuals with particular disabilities--like dementia--who are not well served by either informal arrangements or by formal

Cost Modeling for Fabrication of Direct Drive Inertial Fusion Energy Targets

International Nuclear Information System (INIS)

Rickman, William Samuel; Goodin, Daniel T.

2003-01-01

Chemical engineering analyses are underway for a commercial-scale [1000-MW(electric)] divinyl benzene foam-based Inertial Fusion Energy (IFE) Target Fabrication Facility (TFF). This facility is designed to supply 500,000, 4-mm-outer diameter targets per day - coated via interfacial polycondensation, dried with supercritical CO 2 , sputter coated with Au and/or Pd, and filled with deuterium-tritium layered at cryogenic temperatures and injected into the fusion chamber. Such targets would be used in a direct-drive IFE power plant.The work uses manufacturing processes being developed in the laboratory, chemical engineering scaleup principles, and established cost-estimating methods. The plant conceptual design includes a process flow diagram, mass and energy balances, equipment sizing and sketches, storage tanks, and facility views.The cost estimate includes both capital and operating costs. Initial results for a TFF dedicated to one 1000-MW(electric) plant indicate that the costs per target are well within the commercially viable range. Larger TFF plants [3000 MW(electric)] are projected to lead to significantly reduced costs per injected target. Additional cost reductions are possible by producing dried, sputter-coated empty shells at a central facility that services multiple power plants.The results indicate that the installed capital cost is about $100 million and the annual operating costs will be about $20 million, for a cost per target of about $0.17 each. These design and cost projections assume that a significant process development and scaleup program is successfully completed for all of the basic unit operations included in the facility

Object Tracking with LiDAR: Monitoring Taxiing and Landing Aircraft

Directory of Open Access Journals (Sweden)

Zoltan Koppanyi

2018-02-01

Full Text Available Mobile light detection and ranging (LiDAR sensors used in car navigation and robotics, such as the Velodyne’s VLP-16 and HDL-32E, allow for sensing the surroundings of the platform with high temporal resolution to detect obstacles, tracking objects and support path planning. This study investigates the feasibility of using LiDAR sensors for tracking taxiing or landing aircraft close to the ground to improve airport safety. A prototype system was developed and installed at an airfield to capture point clouds to monitor aircraft operations. One of the challenges of accurate object tracking using the Velodyne sensors is the relatively small vertical field of view (30°, 41.3° and angular resolution (1.33°, 2°, resulting in a small number of points of the tracked object. The point density decreases with the object–sensor distance, and is already sparse at a moderate range of 30–40 m. The paper introduces our model-based tracking algorithms, including volume minimization and cube trajectories, to address the optimal estimation of object motion and tracking based on sparse point clouds. Using a network of sensors, multiple tests were conducted at an airport to assess the performance of the demonstration system and the algorithms developed. The investigation was focused on monitoring small aircraft moving on runways and taxiways, and the results indicate less than 0.7 m/s and 17 cm velocity and positioning accuracy achieved, respectively. Overall, based on our findings, this technology is promising not only for aircraft monitoring but for airport applications.

Energy assessments

International Nuclear Information System (INIS)

Unruh, T.D.

1998-01-01

Energy industry initiatives during the 1970s and during the 1990s are compared. During the 1970s, the objective was to reduce energy consumption and to reduce dependency on foreign fuel. Today, the emphasis is on reducing energy costs and to improve net operating income. The challenges posed by the drive to reduce energy costs are discussed. As a tool in the drive to reduce energy cost, the energy assessment process was described. The process entails a detailed analysis of energy consumption, an investigation of energy rates and an assessment of site conditions and equipment, with a view towards an optimum combination that will lead to energy cost reductions

Optimal control strategy design for extending all-electric driving capability of plug-in hybrid electric vehicles (PHEVs)

Energy Technology Data Exchange (ETDEWEB)

Williamson, S.S [Concordia Univ., Montreal, PQ (Canada). Dept. of Electrical and Computer Engineering, P.D Ziogas Power Electronics Laboratory

2007-07-01

The high voltage energy storage system in plug-in hybrid electric vehicles (PHEVs) is usually a rechargeable type that service a dual purpose, notably to supplement the power delivered by the internal combustion engine, and to provide partial propulsion energy from an off-board source of electricity. The energy storage devices in electric vehicles typically improve vehicle efficiency through engine downsizing and by recapturing braking energy. However, since PHEVs have the ability to recharge their energy storage systems directly from the power grid, the periods of all-electric operation can be extended, thereby reducing the dependence on the internal combustion engine. This is particularly useful in city driving conditions. Developers of PHEV technology are faced with the challenge of choosing the appropriate energy storage battery in order to improve the all-electric drive range. In this study, control strategies were modeled for specific driving load conditions using the Advanced Vehicle Simulator (ADVISOR) software. This paper presented specific control algorithms for PHEV operation for various city driving loads. The optimal design strategy considered the improvement of critical energy storage parameters, overall drive train efficiency, and vehicle performance characteristics. Future trends in the design and development of PHEV drive trains were also presented. 13 figs.

Confinement improvement with rf poloidal current drive in the reversed-field pinch

International Nuclear Information System (INIS)

Hokin, S.; Sarff, J.; Sovinec, C.; Uchimoto, E.

1994-01-01

External control of the current profile in a reversed-field pinch (RFP), by means such as rf poloidal current drive, may have beneficial effects well beyond the direct reduction of Ohmic input power due to auxiliary heating. Reduction of magnetic turbulence associated with the dynamo, which drives poloidal current in a conventional RFP, may allow operation at lower density and higher electron temperature, for which rf current drive becomes efficient and the RFP operates in a more favorable regime on the nτ vs T diagram. Projected parameters for RFX at 2 MA axe studied as a concrete example. If rf current drive allows RFX to operate with β = 10% (plasma energy/magnetic energy) at low density (3 x 10 19 m -3 ) with classical resistivity (i.e. without dynamo-enhanced power input), 40 ms energy confinement times and 3 keV temperatures will result, matching the performance of tokamaks of similar size

Motor drive chassis for the plutonium protection system

International Nuclear Information System (INIS)

Shaut, A.L.

1979-05-01

A motor drive chassis has been developed for use in the Plutonium Protection System. Rotation of the desired carrousel in a secure storage module is controlled by this chassis which supplies the power and drive pulses required by the carrousel motor. This work was sponsored by the Department of Energy/Office of Safeguards and Security (DOE/OSS) as part of the overall Sandia Fixed Physical Protection Program

Control of a 420 KN Discrete Displacement Cylinder Drive for the Wavestar Wave Energy Converter

DEFF Research Database (Denmark)

Hansen, Rico H.; Andersen, Torben Ole; Pedersen, Henrik C.

2014-01-01

absorbers. The system is implemented using multi-chambered cylinders, where the different chambers may be switched between three pressure lines using a manifold with fast on/off valves. Resultantly, a Discrete Displacement Cylinder (DDC) is obtained, where force control is implemented by shifting between...... different area/pressure combinations. Currently, a 420 kN DDC prototype has been implemented and tested at the newly commissioned full size wave energy testbench at Aalborg University. The initial design and control of the DDC had poorly damped switching transients. These issues treated in this paper....... This leads to a new control, which gives a smooth operating DDC, while meeting the requirements to the efficiency of the drive....

Freeway Driving Cycle Construction Based on Real-Time Traffic Information and Global Optimal Energy Management for Plug-In Hybrid Electric Vehicles

Directory of Open Access Journals (Sweden)

Hongwen He

2017-11-01

Full Text Available This paper presents a freeway driving cycle (FDC construction method based on traffic information. A float car collected different type of roads in California and we built a velocity fragment database. We selected a real freeway driving cycle (RFDC and established the corresponding time traffic information tensor model by using the data in California Department of Transportation performance measure system (PeMS. The correlation of road velocity in the time dimension and spatial dimension are analyzed. According to the average velocity of road sections at different times, the kinematic fragments are stochastically selected in the velocity fragment database to construct a real-time FDC of each section. The comparison between construction freeway driving cycle (CFDC and real freeway driving cycle (RFDC show that the CFDC well reflects the RFDC characteristic parameters. Compared to its application in plug-in electric hybrid vehicle (PHEV optimal energy management based on a dynamic programming (DP algorithm, CFDC and RFDC fuel consumption are similar within approximately 5.09% error, and non-rush hour fuel economy is better than rush hour 3.51 (L/100 km at non-rush hour, 4.29 (L/km at rush hour. Moreover, the fuel consumption ratio can be up to 13.17% in the same CFDC at non-rush hour.

Electric driving. Evaluation of transitions based on system options

International Nuclear Information System (INIS)

Nagelhout, D.; Ros, J.P.M.

2009-01-01

Over the past years, electric driving has become more and more attractive because of the development of better batteries. Driving electric vehicles could drastically reduce CO2 emissions, especially if more electricity would be generated by using sustainable energy. As most passenger cars are not used at night, this is the ideal time for charging their batteries. This would be cost-effective because, at that time, there is a surplus of generating capacity, and wind energy could also be used more effectively. Moreover, consumers will be able to drive clean and quiet vehicles at costs that seem surmountable in the future. At least two obstacles still need to be overcome. The first of which is the current maximum range of electric vehicles of around a few hundred kilometres. The second obstacle is the need for a standardised European network of charging stations, and electrical outlets near residences and at commercial and public parking facilities. This report shows the challenges facing the government and the business community of utilising the benefits of electric driving and of overcoming the obstacles [nl

Direct-drive laser-fusion in the US

International Nuclear Information System (INIS)

McCrory, R.L.; Soures, J.M.; Audebert, P.

1986-01-01

Direct-drive experiments at the University of Rochester's Laboratory for Laser Energetics (LLE) and the Naval Research Laboratory (NRL) are presently addressing issues in pellet compression and heating: efficiency of coupling of laser energy to the target and the coupling of absorbed energy to the fuel, drive uniformity, hydrodynamic stability, preheat arising from laser plasma instabilities and x-rays, and target diagnostics. The 24-beam, 2500-Joule, 351 nm OMEGA laser system at LLE has been used in an experimental effort to achieve high compressed DT fuel densities. Detailed hydrodynamic computer simulations at NRL predict that the growth rate of the ablative Rayleigh-Taylor instability is less than the classical values. Recent Rayleigh-Taylor experiments ar NRL are testing these predictions

Electron Transfer in Flavodoxin-based Redox Maquettes

NARCIS (Netherlands)

Alagaratnam, S.

2005-01-01

Small redox proteins play the role of electron taxis in the cell, picking electrons up at one location and delivering them at another. While it is known that these reactions are the basis for the processes of energy generation by respiration and photosynthesis, the means by which these 'taxis'

Predictive routing for autonomous mobility-on-demand systems with ride-sharing

NARCIS (Netherlands)

Alonso Mora, J.; Wallar, Alex; Rus, Daniela; Bicchi, A.; Maciejewski, T.

2017-01-01

Ride-sharing, or carpooling, systems with autonomous vehicles will provide efficient and reliable urban mobility on demand. In this work we present a method for dynamic vehicle routing that leverages historical data to improve the performance of a network of self-driving taxis. In particular, we

Harvesting the decay energy of 26Al to drive lightning discharge in protoplanetary discs

Science.gov (United States)

Johansen, Anders; Okuzumi, Satoshi

2018-01-01

Chondrules in primitive meteorites likely formed by recrystallisation of dust aggregates that were flash-heated to nearly complete melting. Chondrules may represent the building blocks of rocky planetesimals and protoplanets in the inner regions of protoplanetary discs, but the source of ubiquitous thermal processing of their dust aggregate precursors remains elusive. Here we demonstrate that escape of positrons released in the decay of the short-lived radionuclide 26Al leads to a large-scale charging of dense pebble structures, resulting in neutralisation by lightning discharge and flash-heating of dust and pebbles. This charging mechanism is similar to a nuclear battery where a radioactive source charges a capacitor. We show that the nuclear battery effect operates in circumplanetesimal pebble discs. The extremely high pebble densities in such discs are consistent with conditions during chondrule heating inferred from the high abundance of sodium within chondrules. The sedimented mid-plane layer of the protoplanetary disc may also be prone to charging by the emission of positrons, if the mass density of small dust there is at least an order of magnitude above the gas density. Our results imply that the decay energy of 26Al can be harvested to drive intense lightning activity in protoplanetary discs. The total energy stored in positron emission is comparable to the energy needed to melt all solids in the protoplanetary disc. The efficiency of transferring the positron energy to the electric field nevertheless depends on the relatively unknown distribution and scale-dependence of pebble density gradients in circumplanetesimal pebble discs and in the protoplanetary disc mid-plane layer.

A Dynamic Control Strategy for Hybrid Electric Vehicles Based on Parameter Optimization for Multiple Driving Cycles and Driving Pattern Recognition

Directory of Open Access Journals (Sweden)

Zhenzhen Lei

2017-01-01

Full Text Available The driving pattern has an important influence on the parameter optimization of the energy management strategy (EMS for hybrid electric vehicles (HEVs. A new algorithm using simulated annealing particle swarm optimization (SA-PSO is proposed for parameter optimization of both the power system and control strategy of HEVs based on multiple driving cycles in order to realize the minimum fuel consumption without impairing the dynamic performance. Furthermore, taking the unknown of the actual driving cycle into consideration, an optimization method of the dynamic EMS based on driving pattern recognition is proposed in this paper. The simulation verifications for the optimized EMS based on multiple driving cycles and driving pattern recognition are carried out using Matlab/Simulink platform. The results show that compared with the original EMS, the former strategy reduces the fuel consumption by 4.36% and the latter one reduces the fuel consumption by 11.68%. A road test on the prototype vehicle is conducted and the effectiveness of the proposed EMS is validated by the test data.

Lower hybrid current drive in tokamak plasmas

Energy Technology Data Exchange (ETDEWEB)

Ushigusa, Kenkichi [Japan Atomic Energy Research Inst., Naka, Ibaraki (Japan). Naka Fusion Research Establishment

1999-03-01

Past ten years progress on Lower Hybrid Current Drive (LHCD) experiments have demonstrated the largest non-inductive current (3.6 MA, JT-60U), the longest current sustainment (2 hours, TRIAM-1M), non-inductive current drive at the highest density (n-bar{sub e} - 10{sup 20}m{sup -3}, ALCATOR-C) and the highest current drive efficiency ({eta}{sub CD} = 3.5x10{sup 19} m{sup -2}A/W, JT-60). These results indicate that LHCD is one of the most promising methods to drive non-inductive current in the present tokamak plasmas. This paper presents recent experimental results on LHCD experiments. Basic theories of LH waves, the wave propagation and the current drive are briefly summarized. The main part of this paper describes several important results and their physical pictures on recent LHCD experiments; 1) the experimental set-up, 2) the current drive efficiency, 3) the control of current profile and MHD activities, 4) the global energy confinement, 5) the global power flow, 6) fast electron behavior, 7) interaction between LH waves and thermal/fast ions, 8) combination with other CD method. (author)

Identifying Method of Drunk Driving Based on Driving Behavior

Directory of Open Access Journals (Sweden)

Xiaohua Zhao

2011-05-01

Full Text Available Drunk driving is one of the leading causes contributing to traffic crashes. There are numerous issues that need to be resolved with the current method of identifying drunk driving. Driving behavior, with the characteristic of real-time, was extensively researched to identify impaired driving behaviors. In this paper, the drives with BACs above 0.05% were defined as drunk driving state. A detailed comparison was made between normal driving and drunk driving. The experiment in driving simulator was designed to collect the driving performance data of the groups. According to the characteristics analysis for the effect of alcohol on driving performance, seven significant indicators were extracted and the drunk driving was identified by the Fisher Discriminant Method. The discriminant function demonstrated a high accuracy of classification. The optimal critical score to differentiate normal from drinking state was found to be 0. The evaluation result verifies the accuracy of classification method.

Energy Efficient Control of High Speed IPMSM Drives - A Generalized PSO Approach

Directory of Open Access Journals (Sweden)

GECIC, M.

2016-02-01

Full Text Available In this paper, a generalized particle swarm optimization (GPSO algorithm was applied to the problems of optimal control of high speed low cost interior permanent magnet motor (IPMSM drives. In order to minimize the total controllable electrical losses and to increase the efficiency, the optimum current vector references are calculated offline based on GPSO for the wide speed range and for different load conditions. The voltage and current limits of the drive system and the variation of stator inductances are all included in the optimization method. The stored optimal current vector references are used during the real time control and the proposed algorithm is compared with the conventional high speed control algorithm, which is mostly voltage limit based. The computer simulations and experimental results on 1 kW low cost high speed IPMSM drive are discussed in details.

Exploring driving factors of energy-related CO2 emissions in Chinese provinces: A case of Liaoning

International Nuclear Information System (INIS)

Geng, Yong; Zhao, Hongyan; Liu, Zhu; Xue, Bing; Fujita, Tsuyoshi; Xi, Fengming

2013-01-01

In order to uncover driving forces for provincial CO 2 emission in China, a case study was undertaken to shed light on the CO 2 emission growth in such a region. Liaoning province was selected due to its typical features as one industrial province. The environmental input–output analysis and structure decomposing analysis have been conducted in order to provide a holistic picture on Liaoning's CO 2 emissions during 1997–2007. Research outcomes indicate that rapid increase of per capita consumption activities is the main driver for Liaoning to have a significant CO 2 emission growth, followed by consumption structure, production structure and population size. Energy intensity and energy structure partly offset the CO 2 emission increase. Electricity power and heat supply and construction sectors caused the most CO 2 emission, indicating that more specific mitigation policies for these two sectors should be prepared. From final demand point of view, it is clear that trade plays a leading role in regional CO 2 emission, followed by fixed capital investment and urban household consumption which become increasingly important over time. Consequently, in order to realize low carbon development, local governments should consider all these factors so that appropriate mitigation policies can be raised by considering the local realities. - Highlights: • Driving forces for Liaoning's CO 2 emission have been uncovered through the use of IO-SDA model. • Construction and electricity power/heat supply sectors have the highest embodied emissions. • Trade plays a key role on regional CO 2 emission in Chinese old industrial base. • Fixed capital investment and urban households generated more CO 2 emissions

Alcubierre's warp drive: Problems and prospects

International Nuclear Information System (INIS)

Broeck, Chris van den

2000-01-01

Alcubierre's warp drive geometry seemingly represents the ultimate dream for interstellar travel: there is no speed limit, the passengers are weightless whatever the acceleration, and there is no time dilation. However, in its original form, the proposal suffers from several fatal flaws, such as unreasonably high energies, energy moving in a locally spacelike direction, and a violation of the energy conditions of classical Einstein gravity. I present a possible solution for one of these problems, and I suggest ways to at least soften the others

Driving forces behind the stagnancy of China's energy-related CO2 emissions from 1996 to 1999: the relative importance of structural change, intensity change and scale change

International Nuclear Information System (INIS)

Libo Wu; Kaneko, S.; Matsuoka, S.

2005-01-01

It is noteworthy that income elasticity of energy consumption in China shifted from positive to negative after 1996, accompanied by an unprecedented decline in energy-related CO 2 emissions. This paper therefore investigate the evolution of energy-related CO 2 emissions in China from 1985 to 1999 and the underlying driving forces, using the newly proposed three-level 'perfect decomposition' method and provincially aggregated data. The province-based estimates and analyses reveal a 'sudden stagnancy' of energy consumption, supply and energy-related CO 2 emissions in China from 1996 to 1999. The speed of a decrease in energy intensity and a slowdown in the growth of average labor productivity of industrial enterprises may have been the dominant contributors to this 'stagnancy'. The findings of this paper point to the highest rate of deterioration of state-owned enterprises in early 1996, the industrial restructuring caused by changes in ownership, the shutdown of small-scale power plants, and the introduction of policies to improve energy efficiency as probable factors. Taking into account the characteristics of those key driving forces, we characterize China's decline of energy-related CO 2 emissions as a short-term fluctuation and incline to the likelihood that China will resume an increasing trend from a lower starting point in the near future. (author)

Self-rated driving and driving safety in older adults.

Science.gov (United States)

Ross, Lesley A; Dodson, Joan E; Edwards, Jerri D; Ackerman, Michelle L; Ball, Karlene

2012-09-01

Many U.S. states rely on older adults to self-regulate their driving and determine when driving is no longer a safe option. However, the relationship of older adults' self-rated driving in terms of actual driving competency outcomes is unclear. The current study investigates self-rated driving in terms of (1) systematic differences between older adults with high (good/excellent) versus low (poor/fair/average) self-ratings, and (2) the predictive nature of self-rated driving to adverse driving outcomes in older adults (n=350; mean age 73.9, SD=5.25, range 65-91). Adverse driving outcomes included self-reported incidences of (1) being pulled over by the police, (2) receiving a citation, (3) receiving a recommendation to cease or limit driving, (4) crashes, and (5) state-reported crashes. Results found that older drivers with low self-ratings reported more medical conditions, less driving frequency, and had been given more suggestions to stop/limit their driving; there were no other significant differences between low and high self-raters. Logistic regression revealed older drivers were more likely to have a state-reported crash and receive a suggestion to stop or limit driving. Men were more likely to report all adverse driving outcomes except for receiving a suggestion to stop or limit driving. Regarding self-rated driving, older adults with high ratings were 66% less likely (OR=0.34, 95% CI=0.14-0.85) to have received suggestions to limit or stop driving after accounting for demographics, health and driving frequency. Self-ratings were not predictive of other driving outcomes (being pulled over by the police, receiving a citation, self-reported crashes, or state-reported crashes, ps>0.05). Most older drivers (85.14%) rated themselves as either good or excellent drivers regardless of their actual previous citation or crash rates. Self-rated driving is likely not related to actual driving proficiency as indicated by previous crash involvement in older adults

Do effects of theoretical training and rewards for energy-efficient behavior persist over time and interact? A natural field experiment on eco-driving in a company fleet

International Nuclear Information System (INIS)

Schall, Dominik L.; Wolf, Menas; Mohnen, Alwine

2016-01-01

Increasing energy efficiency is a cornerstone of policy initiatives to tackle climate change and increase corporate sustainability. Convincing people to drive more fuel-efficiently (“eco-driving”) is often an integral part of these approaches, especially in the transport sector. But there is a lack of studies on the long-term persistence and potential interaction of the effects of incentives and training on energy conservation behavior in general and eco-driving behavior in particular. We address this gap with a twelve months long natural field experiment in a logistics company to analyze the time-dependent and potentially interacting effects of rewards and theoretical training for eco-driving on fuel consumption in a real-world setting. We find an immediate reduction of fuel consumption following the introduction of a non-monetary reward and an attenuation of this effect over time. Theoretical eco-driving training shows no effect, neither short-term nor long-term, highlighting the often neglected necessity to include practical training elements. Contrary to common assumptions, the interaction of incentives and theoretical training does not show an additional reduction effect. Our results demonstrate the difficulty of changing engrained behavior and habits, and underline the need for a careful selection and combination of interventions. Policy implications for public and private actors are discussed. - Highlights: • Natural field experiment on training and incentives for fuel-efficient driving. • Focus on long-term and interaction effects over twelve months. • Immediate reduction effect of non-monetary reward that attenuates over time. • Theoretical eco-driving training shows no effect, neither short-term nor long-term. • Interaction of incentives and training shows no additional reduction effect.

The Drive-Wise Project: Driving Simulator Training increases real driving performance in healthy older drivers

Directory of Open Access Journals (Sweden)

Gianclaudio eCasutt

2014-05-01

Full Text Available Background: Age-related cognitive decline is often associated with unsafe driving behavior. We hypothesized that 10 active training sessions in a driving simulator increase cognitive and on-road driving performance. In addition, driving simulator training should outperform cognitive training.Methods: Ninety-one healthy active drivers (62 – 87 years were randomly assigned to either (1 a driving simulator training group, (2 an attention training group (vigilance and selective attention, or (3 a control group. The main outcome variables were on-road driving and cognitive performance. Seventy-seven participants (85% completed the training and were included in the analyses. Training gains were analyzed using a multiple regression analysis with planned comparisons.Results: The driving simulator training group showed an improvement in on-road driving performance compared to the attention training group. In addition, both training groups increased cognitive performance compared to the control group. Conclusion: Driving simulator training offers the potential to enhance driving skills in older drivers. Compared to the attention training, the simulator training seems to be a more powerful program for increasing older drivers’ safety on the road.

Self-rated Driving and Driving Safety in Older Adults

OpenAIRE

Ross, Lesley A.; Dodson, Joan; Edwards, Jerri D.; Ackerman, Michelle L.; Ball, Karlene

2012-01-01

Many U.S. states rely on older adults to self-regulate their driving and determine when driving is no longer a safe option. However, the relationship of older adults’ self-rated driving in terms of actual driving competency outcomes is unclear. The current study investigates self-rated driving in terms of (1) systematic differences between older adults with high (good/excellent) versus low (poor/fair/average) self-ratings, and (2) the predictive nature of self-rated driving to adverse driving...

Photoelectric panel with equatorial mounting of drive

Science.gov (United States)

Kukhta, M. S.; Krauinsh, P. Y.; Krauinsh, D. P.; Sokolov, A. P.; Mainy, S. B.

2018-03-01

The relevance of the work is determined by the need to create effective models for sunny energy. The article considers a photoelectric panel equipped with a system for tracking the sun. Efficiency of the system is provided by equatorial mounting, which compensates for the rotation of the Earth by rotating the sunny panel in the plane of the celestial equator. The specificity of climatic and geographical conditions of Tomsk is estimated. The dynamics of power variations of photoelectric panels with equatorial mounting during seasonal fluctuations in Tomsk is calculated. A mobile photovoltaic panel with equatorial mounting of the drive has been developed. The methods of design strategy for placing photovoltaic panels in the architectural environment of the city are presented. Key words: sunny energy, photovoltaics, equatorial mounting, mechatronic model, wave reducer, electric drive.

An Energy Efficient Hydraulic Winch Drive Concept Based on a Speed-variable Switched Differential Pump

DEFF Research Database (Denmark)

Schmidt, Lasse; Andersen, Torben O.; Pedersen, Henrik Clemmensen

2017-01-01

controls. Such solutions are typically constituted by many and rather expensive components, and are furthermore often suffering from low frequency dynamics. In this paper an alternative solution is proposed for winch drive operation, which is based on the so-called speed-variable switched differential pump......, originally designed for direct drive of hydraulic differential cylinders. This concept utilizes three pumps, driven by a single electric servo drive. The concept is redesigned for usage in winch drives, driven by flow symmetric hydraulic motors and single directional loads as commonly seen in e.g. active...... heave compensation applications. A general drive configuration approach is presented, along with a proper control strategy and design. The resulting concept is evaluated when applied for active heave compensation. Results demonstrate control performance on level with conventional valve solutions...

Optimization of parameters of special asynchronous electric drives

Science.gov (United States)

Karandey, V. Yu; Popov, B. K.; Popova, O. B.; Afanasyev, V. L.

2018-03-01

The article considers the solution of the problem of parameters optimization of special asynchronous electric drives. The solution of the problem will allow one to project and create special asynchronous electric drives for various industries. The created types of electric drives will have optimum mass-dimensional and power parameters. It will allow one to realize and fulfill the set characteristics of management of technological processes with optimum level of expenses of electric energy, time of completing the process or other set parameters. The received decision allows one not only to solve a certain optimizing problem, but also to construct dependences between the optimized parameters of special asynchronous electric drives, for example, with the change of power, current in a winding of the stator or rotor, induction in a gap or steel of magnetic conductors and other parameters. On the constructed dependences, it is possible to choose necessary optimum values of parameters of special asynchronous electric drives and their components without carrying out repeated calculations.

What drives the change in China's energy intensity: Combining decomposition analysis and econometric analysis at the provincial level

International Nuclear Information System (INIS)

Song, Feng; Zheng, Xinye

2012-01-01

We employ decomposition analysis and econometric analysis to investigate the driving forces behind China's changing energy intensity using a provincial-level panel data set for the period from 1995 to 2009. The decomposition analysis indicates that: (a) all of the provinces except for a few experienced efficiency improvement, while around three-fourths of the provinces' economics became more energy intensive or remained unchanged; (b) consequently the efficiency improvement accounts for more than 90% of China's energy intensity change as opposed to the economic structural change. The econometric analysis shows that the rising income plays a significant role in the reduction of energy intensity while the effect of energy price is relatively limited. The result may reflect the urgency of deregulating the price and establishing a market-oriented pricing system in China's energy sector. The implementation of the energy intensity reduction policies in the Eleventh Five-Year Plan (FYP) has helped reverse the increasing trend of energy intensity since 2002. Although the Chinese Government intended to change the industry-led economic growth pattern, it seems that most of the policy effects flow through the efficiency improvement as opposed to the economic structure adjustment. More fundamental changes to the economic structure are needed to achieve more sustainable progress in energy intensity reduction. - Highlights: ► We examine the determinants of China's energy intensity change at provincial level. ► Rising income plays a significant role in reducing China's energy intensity. ► Policy effects mainly flow through the efficiency improvement. ► Fundamental structure changes are needed to further reduce China's energy intensity.

Switched reluctance drive for mass application

Energy Technology Data Exchange (ETDEWEB)

Bitchkov, M.G.; Ilinski, N.F.; Sementchuk, V.A. [Moscow Power Engineering Inst. (Russian Federation)

2000-07-01

Variable speed drives (VSDs) are the most effective means for energy saving in many practical applications particularly in pumps, fans, compressors, conveyors, etc. Up to now the only wide used VSD is a frequency controlled electric drive with AC induction motor. A switched reluctance drive (SRD) having noticeable advantages such as simple construction, low cost, high reliability, high efficiency, etc. still does not compete with traditional AC drives mainly because of the following unsolved problems: complexity of proper control, necessity of a rotor position sensor, poor acoustic characteristics. Results of R and D project realised in Moscow Power Engineering Institute in co-operation with Jaroslavl electric machine-building plant allowed to overcome the above mentioned problems and to obtain reliable low cost sensorless SRD with high efficiency and acceptable acoustic characteristics. The original sensorless SRD version is based on current measuring and exploiting a specially organized observer that provides a stable drive operation within broad speed-torque ranges. Acoustic SRD characteristics were improved by means of proper current pulses shape control. Small increasing the time of current pulse trailing edge allowed to decrease the noise level to 70 dB(A) and brought the SRD to a vary smooth operation even at a low speed. (orig.)

Improving Motor and Drive System Performance – A Sourcebook for Industry

Energy Technology Data Exchange (ETDEWEB)

None

2014-02-01

This sourcebook outlines opportunities to improve motor and drive systems performance. The sourcebook is divided into four main sections: (1) Motor and Drive System Basics: Summarizes important terms, relationships, and system design considerations relating to motor and drive systems. (2) Performance Opportunity Road Map: Details the key components of well-functioning motor and drive systems and opportunities for energy performance opportunities. (3) Motor System Economics: Offers recommendations on how to propose improvement projects based on corporate priorities, efficiency gains, and financial payback periods. (4) Where to Find Help: Provides a directory of organizations associated with motors and drives, as well as resources for additional information, tools, software, videos, and training opportunities.

Electromotor control rod drive for nuclear reactors

International Nuclear Information System (INIS)

Baker, S.M.

1975-01-01

The positioning of a control rod arranged in a pressure vessel takes place with a drive. This protrudes out of the pressure vessel through a support and is formed from a rotating field motor with energy source, e.g. alternating current connection. Its stator surrounds a section of a pressure casing which covers the length of the drive. The rotor is arranged in the pressure casing and interacts with a shaft lying in the rotation axis. Furthermore, segments are hinged on it, each of which forms two arms of a rocker. Each segment can be revolved against a storing force in a plane containing the rotation axis, through the stator field acting on one of the rocker arms. In order that the drive motor is automatically blocked should the electricity supply fail, the other rocker arm can be connected with a fixed cased component of the drive having the effect of a friction break or a form-locking mechanical catch. (DG/LH) [de

Laser-Plasma Interactions in Drive Campaign targets on the National Ignition Facility

International Nuclear Information System (INIS)

Hinkel, D E; Callahan, D A; Moody, J D; Amendt, P A; Lasinski, B F; MacGowan, B J; Meeker, D; Michel, P A; Ralph, J; Rosen, M D; Ross, J S; Schneider, M B; Storm, E; Strozzi, D J; Williams, E A

2016-01-01

The Drive campaign [D A Callahan et al., this conference] on the National Ignition Facility (NIF) laser [E. I. Moses, R. N. Boyd, B. A. Remington, C. J. Keane, R. Al-Ayat, Phys. Plasmas 16, 041006 (2009)] has the focused goal of understanding and optimizing the hohlraum for ignition. Both the temperature and symmetry of the radiation drive depend on laser and hohlraum characteristics. The drive temperature depends on the coupling of laser energy to the hohlraum, and the symmetry of the drive depends on beam-to-beam interactions that result in energy transfer [P. A. Michel, S. H. Glenzer, L. Divol, et al, Phys. Plasmas 17, 056305 (2010).] within the hohlraum. To this end, hohlraums are being fielded where shape (rugby vs. cylindrical hohlraums), gas fill composition (neopentane at room temperature vs. cryogenic helium), and gas fill density (increase of ∼ 150%) are independently changed. Cylindrical hohlraums with higher gas fill density show improved inner beam propagation, as should rugby hohlraums, because of the larger radius over the capsule (7 mm vs. 5.75 mm in a cylindrical hohlraum). Energy coupling improves in room temperature neopentane targets, as well as in hohlraums at higher gas fill density. In addition cross-beam energy transfer is being addressed directly by using targets that mock up one end of a hohlraum, but allow observation of the laser beam uniformity after energy transfer. Ideas such as splitting quads into “doublets” by re-pointing the right and left half of quads are also being pursued. LPI results of the Drive campaign will be summarized, and analyses of future directions presented. (paper)

Scenario analysis of carbon emissions' anti-driving effect on Qingdao's energy structure adjustment with an optimization model, Part II: Energy system planning and management.

Science.gov (United States)

Wu, C B; Huang, G H; Liu, Z P; Zhen, J L; Yin, J G

2017-03-01

In this study, an inexact multistage stochastic mixed-integer programming (IMSMP) method was developed for supporting regional-scale energy system planning (EPS) associated with multiple uncertainties presented as discrete intervals, probability distributions and their combinations. An IMSMP-based energy system planning (IMSMP-ESP) model was formulated for Qingdao to demonstrate its applicability. Solutions which can provide optimal patterns of energy resources generation, conversion, transmission, allocation and facility capacity expansion schemes have been obtained. The results can help local decision makers generate cost-effective energy system management schemes and gain a comprehensive tradeoff between economic objectives and environmental requirements. Moreover, taking the CO 2 emissions scenarios mentioned in Part I into consideration, the anti-driving effect of carbon emissions on energy structure adjustment was studied based on the developed model and scenario analysis. Several suggestions can be concluded from the results: (a) to ensure the smooth realization of low-carbon and sustainable development, appropriate price control and fiscal subsidy on high-cost energy resources should be considered by the decision-makers; (b) compared with coal, natural gas utilization should be strongly encouraged in order to insure that Qingdao could reach the carbon discharges peak value in 2020; (c) to guarantee Qingdao's power supply security in the future, the construction of new power plants should be emphasised instead of enhancing the transmission capacity of grid infrastructure. Copyright © 2016 Elsevier Ltd. All rights reserved.

Comparative Analysis of Passenger Traffic Fleets in Asian Cities: Technology, Driving Activities, and Emission

Science.gov (United States)

KIM Oanh, N. T.; Huynh, H. V.; Saikawa, E.

2015-12-01

The road transport sector is the major emission source of toxic air pollutants and greenhouse gases (GHGs) in large Asian cities. This paper comparatively analyzed on-road passenger traffic fleets (cars, buses, taxis, motorcycles), using local data collected in cities of Bangkok (BKK), Kathmandu, Hanoi, Ho Chi Minh City (HCMC), and Yangon. Surveys were done in 2010-2014 to obtain information on vehicle technology, driving activities (speed, distance, number, and types of starts), traffic density, and fuel characteristics. Large shares of pre-Euro vehicles were still observed, especially for public buses. The most advanced technology was Euro4, which was observed in small shares (<5%) of the personal car fleets in BKK, HCMC, and Yangon. Euro3 was generally the most advanced technology found in other fleets in these cities. Motorcycles (MC) was the most dominant fleet in all cities, except in Yangon, where they were not allowed. Low vehicle speeds, mainly below 25 km/h, were observed for all vehicle types, indicating traffic jams. Natural gas and LPG had considerable shares in BKK and Yangon while for other cities diesel and gasoline were still the two major fuels used in transportation. Running emission factors (EF) of buses and taxis in Kathmandu were considerably higher than other cities due to its hilly topography, low speeds, high mileage, and less advanced vehicle technologies. The number of passenger vehicles per 1000 people were 400-500 in HCMC and Hanoi (mainly by MC) and in BKK (also by cars), moderate in Kathmandu (200) and the lowest in Yangon (40) because of the MC ban. Annual emissions of the passenger fleets were calculated for each city using the International Vehicle Emission (IVE) for 14 species. BC and OC emissions were estimated using their fractions of PM10 emission. Annual emission per capita of toxic air pollutants and GHGs was analyzed. For example, the emission in kg/year/person for CO, VOC, NOx and PM10 in these cities was 24-150 for CO, 0

Short primary linear drive designed for synchronous and induction operation mode with on-board energy storage

Energy Technology Data Exchange (ETDEWEB)

Fernandes Neto, Tobias Rafael

2012-06-28

The idea of a flexible industrial manufacturing system for the transfer of material, tooling, processing/filling, etc., in which several vehicles can travel with high speed, high degree of independency and high precision is proposed in this thesis. Such flexible systems show a meaningful economic potential for modern manufacturing systems. The basic concept is that a linear motor has the secondary part fixed to the track while the primary (moving winding) travels along the track (short primary topology). The same principle can work in the other way around, arranging the primary in segments and letting the secondary (carrier) to move from segment to segment (long primary topology). The concept's implementation involves technical issues, such as: the position measurement, the energy and information transfer, the individual position and speed control of the vehicle in which varying speeds increase the possibility of collision, and the smooth transition between segments or different types of the secondary. Finally, multiple vehicles traveling at high speed, high positioning repeatability and rapid acceleration rates increase the production throughout and the reliability compared to conventional manufacturing conveyor systems. As an example, a transporting and processing system based on linear drives is a continuous and closed structure with multiple loops, which permits the safe transport of fragile loads. Although such solutions often need higher investment costs, the lack of mechanical coupling parts and wearing elements in these motors greatly increases their reliability. The long primary topology allows a passive and lightweight vehicle (secondary), avoiding brushes and cables to transfer energy and information. For long distances, the primary is arranged in several electrical independent segments. On the other hand, the short primary configuration uses the winding mounted on the moving part (active vehicle) to produce the traveling wave, the secondary as

Driving-behavior-aware stochastic model predictive control for plug-in hybrid electric buses

International Nuclear Information System (INIS)

Li, Liang; You, Sixiong; Yang, Chao; Yan, Bingjie; Song, Jian; Chen, Zheng

2016-01-01

Highlights: • The novel approximated global optimal energy management strategy has been proposed for hybrid powertrains. • Eight typical driving behaviors have been classified with K-means to deal with the multiplicative traffic conditions. • The stochastic driver models of different driving behaviors were established based on the Markov chains. • ECMS was used to modify the SMPC-based energy management strategy to improve its fuel economy. • The approximated global optimal energy management strategy for plug-in hybrid electric buses has been verified and analyzed. - Abstract: Driving cycles of a city bus is statistically characterized by some repetitive features, which makes the predictive energy management strategy very desirable to obtain approximate optimal fuel economy of a plug-in hybrid electric bus. But dealing with the complicated traffic conditions and finding an approximated global optimal strategy which is applicable to the plug-in hybrid electric bus still remains a challenging technique. To solve this problem, a novel driving-behavior-aware modified stochastic model predictive control method is proposed for the plug-in hybrid electric bus. Firstly, the K-means is employed to classify driving behaviors, and the driver models based on Markov chains is obtained under different kinds of driving behaviors. While the obtained driver behaviors are regarded as stochastic disturbance inputs, the local minimum fuel consumption might be obtained with a traditional stochastic model predictive control at each step, taking tracking the reference battery state of charge trajectory into consideration in the finite predictive horizons. However, this technique is still accompanied by some working points with reduced/worsened fuel economy. Thus, the stochastic model predictive control is modified with the equivalent consumption minimization strategy to eliminate these undesirable working points. The results in real-world city bus routines show that the

The eco-driving effect of electric vehicles compared to conventional gasoline vehicles

Directory of Open Access Journals (Sweden)

Hideki Kato

2016-10-01

Full Text Available Eco-driving is attractive to the public, not only users of internal-combustion-engine vehicles (ICEVs including hybrid electric vehicles (HEVs but also users of electric vehicles (EVs have interest in eco-driving. In this context, a quantitative evaluation of eco-driving effect of EVs was conducted using a chassis dynamometer (C/D with an “eco-driving test mode.” This mode comprised four speed patterns selected from fifty-two real-world driving datasets collected during an eco-driving test-ride event. The four patterns had the same travel distance (5.2 km, but showed varying eco-driving achievement levels. Three ICEVs, one HEV and two EVs were tested using a C/D. Good linear relationships were found between the eco-driving achievement level and electric or fuel consumption rate of all vehicles. The reduction of CO2 emissions was also estimated. The CO2-reduction rates of the four conventional (including hybrid vehicles were 10.9%–12.6%, while those of two types of EVs were 11.7%–18.4%. These results indicate that the eco-driving tips for conventional vehicles are effective to not only ICEVs and HEVs but also EVs. Furthermore, EVs have a higher potential of eco-driving effect than ICEVs and HEVs if EVs could maintain high energy conversion efficiency at low load range. This study is intended to support the importance of the dissemination of tools like the intelligent speed adaptation (ISA to obey the regulation speed in real time. In the future, also in the development and dissemination of automated driving systems, the viewpoint of achieving the traveling purpose with less kinetic energy would be important.

Underwater Sound Propagation from Marine Pile Driving.

Science.gov (United States)

Reyff, James A

2016-01-01

Pile driving occurs in a variety of nearshore environments that typically have very shallow-water depths. The propagation of pile-driving sound in water is complex, where sound is directly radiated from the pile as well as through the ground substrate. Piles driven in the ground near water bodies can produce considerable underwater sound energy. This paper presents examples of sound propagation through shallow-water environments. Some of these examples illustrate the substantial variation in sound amplitude over time that can be critical to understand when computing an acoustic-based safety zone for aquatic species.

Resonant driving of a nonlinear Hamiltonian system

International Nuclear Information System (INIS)

Palmisano, Carlo; Gervino, Gianpiero; Balma, Massimo; Devona, Dorina; Wimberger, Sandro

2013-01-01

As a proof of principle, we show how a classical nonlinear Hamiltonian system can be driven resonantly over reasonably long times by appropriately shaped pulses. To keep the parameter space reasonably small, we limit ourselves to a driving force which consists of periodic pulses additionally modulated by a sinusoidal function. The main observables are the average increase of kinetic energy and of the action variable (of the non-driven system) with time. Applications of our scheme aim for driving high frequencies of a nonlinear system with a fixed modulation signal.

Coaster - Drive development; Coaster Gentle Mobile. Antriebsentwicklung. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Mathoy, A.

2004-07-01

This comprehensive final report for the Swiss Federal Office of Energy (SFOE) discusses various electrical drive systems for a proposed people-mover system using motorised cabins on a carrier-structure similar to that of a roller-coaster. The system, suitable for both city applications and as a transport / fun system in mountainous tourist areas, is described. Various options for energy storage are discussed and their advantages and disadvantages are described. Drive concepts and system characteristics are discussed in detail. Test runs with a coaster test-platform on a short stretch of line are described, as is further testing on a stationary test-bed. The report is completed with a review of further work to be done in a second phase before the product is commercialised.

The Role of Interaction Patterns with Hybrid Electric Vehicle Eco-Features for Drivers' Eco-Driving Performance.

Science.gov (United States)

Arend, Matthias G; Franke, Thomas

2017-03-01

The objective of the present research was to understand drivers' interaction patterns with hybrid electric vehicles' (HEV) eco-features (electric propulsion, regenerative braking, neutral mode) and their relationship to fuel efficiency and driver characteristics (technical system knowledge, eco-driving motivation). Eco-driving (driving behaviors performed to achieve higher fuel efficiency) has the potential to reduce CO 2 emissions caused by road vehicles. Eco-driving in HEVs is particularly challenging due to the systems' dynamic energy flows. As a result, drivers are likely to show diverse eco-driving behaviors, depending on factors like knowledge and motivation. The eco-features represent an interface for the control of the systems' energy flows. A sample of 121 HEV drivers who had constantly logged their fuel consumption prior to the study participated in an online questionnaire. Drivers' interaction patterns with the eco-features were related to fuel efficiency. A common factor was identified in an exploratory factor analysis, characterizing the intensity of actively dealing with electric energy, which was also related to fuel efficiency. Driver characteristics were not related to this factor, yet they were significant predictors of fuel efficiency. From the perspective of user-energy interaction, the relationship of the aggregated factor to fuel efficiency emphasizes the central role of drivers' perception of and interaction with energy conversions in determining HEV eco-driving success. To arrive at an in-depth understanding of drivers' eco-driving behaviors that can guide interface design, authors of future research should be concerned with the psychological processes that underlie drivers' interaction patterns with eco-features.

Dementia & Driving

Science.gov (United States)

... have to give up driving. Many people associate driving with self-reliance and freedom; the loss of driving privileges ... familiar roads and avoid long distances. Avoid heavy traffic and heavily traveled roads. Avoid driving at night and in bad weather. Reduce the ...

Evaluation of the Renault Express Electrique over six different driving cycles

NARCIS (Netherlands)

2000-01-01

A Renault Express Electrique with a conventional drive line has been evaluated by IAE over a range of six different drive cycles. Each cycle was driven once, with a fully charged battery. From the measurement results the energy consumption and the cycle length were examined. This document contains a

Assessment of potential energy savings following the replacement of gear-motor-driven systems by frequency-converter-fed direct drives; Energiesparpotential bei Ersatz von Getriebemotoren durch FU-Antriebe. Potentialanalyse

Energy Technology Data Exchange (ETDEWEB)

Tanner, R.; Riesen, H. J.

2007-03-15

This project deals with the energy saving potential that can be achieved by replacing gear motor driven systems by frequency converter fed direct drives. Estimates have shown that due to the high percentage of gear motor installations, which amounts to approximately 10% of all motor driven systems, a significant amount of energy could be saved. However, several barriers impose major restrictions to the broad application of such actions: With the exception of worm gears that reach about 20% of all gear drives, todays' gears already offer a high efficiency of 97-98%. Gear motors are often included in OEM integrated solutions. Many processes require complex adaptations that can complicate replacements or make it even impractical. For low speed or high torque requirements, gear motors may have a dominant advantage concerning the compactness. Our investigations have shown, that in spite of such barriers the replacement of gear motors by direct motors can sum up to a significant amount of energy savings in many cases. Looking at the worm gear systems and the restricted speed and torque ranges that are covered by the direct drives from several suppliers we assume a total saving potential of about 78 GWh per year for Switzerland. (author)

Photoinduced electron transfer in covalent ruthenium-anthraquinone dyads: relative importance of driving-force, solvent polarity, and donor-bridge energy gap.

Science.gov (United States)

Hankache, Jihane; Wenger, Oliver S

2012-02-28

Four rigid rod-like molecules comprised of a Ru(bpy)(3)(2+) (bpy = 2,2'-bipyridine) photosensitizer, a 9,10-anthraquinone electron acceptor, and a molecular bridge connecting the two redox partners were synthesized and investigated by optical spectroscopic and electrochemical means. An attempt was made to assess the relative importance of driving-force, solvent polarity, and bridge variation on the rates of photoinduced electron transfer in these molecules. Expectedly, introduction of tert-butyl substituents in the bipyridine ligands of the ruthenium complex and a change in solvent from dichloromethane to acetonitrile lead to a significant acceleration of charge transfer rates. In dichloromethane, photoinduced electron transfer is not competitive with the inherent excited-state deactivation processes of the photosensitizer. In acetonitrile, an increase in driving-force by 0.2 eV through attachment of tert-butyl substituents to the bpy ancillary ligands causes an increase in electron transfer rates by an order of magnitude. Replacement of a p-xylene bridge by a p-dimethoxybenzene spacer entails an acceleration of charge transfer rates by a factor of 3.5. In the dyads from this study, the relative order of importance of individual influences on electron transfer rates is therefore as follows: solvent polarity ≥ driving-force > donor-bridge energy gap.

Exciplex-triplet energy transfer: A new method to achieve extremely efficient organic light-emitting diode with external quantum efficiency over 30% and drive voltage below 3 V

Science.gov (United States)

Seo, Satoshi; Shitagaki, Satoko; Ohsawa, Nobuharu; Inoue, Hideko; Suzuki, Kunihiko; Nowatari, Hiromi; Yamazaki, Shunpei

2014-04-01

A novel approach to enhance the power efficiency of an organic light-emitting diode (OLED) by employing energy transfer from an exciplex to a phosphorescent emitter is reported. It was found that excitation energy of an exciplex formed between an electron-transporting material with a π-deficient quinoxaline moiety and a hole-transporting material with aromatic amine structure can be effectively transferred to a phosphorescent iridium complex in an emission layer of a phosphorescent OLED. Moreover, such an exciplex formation increases quantum efficiency and reduces drive voltage. A highly efficient, low-voltage, and long-life OLED based on this energy transfer is also demonstrated. This OLED device exhibited extremely high external quantum efficiency of 31% even without any attempt to enhance light outcoupling and also achieved a low drive voltage of 2.8 V and a long lifetime of approximately 1,000,000 h at a luminance of 1,000 cd/m2.

A qualitative exploration of driving stress and driving discourtesy.

Science.gov (United States)

Scott-Parker, B; Jones, C M; Rune, K; Tucker, J

2018-05-31

Driving courtesy, and conversely driving discourtesy, recently has been of great interest in the public domain. In addition, there has been increasing recognition of the negative impact of stress upon the individual's health and wellbeing, with a plethora of interventions aimed at minimising stress more generally. The research literature regarding driving dis/courtesy, in comparison, is scant, with a handful of studies examining the dis/courteous driving behaviour of road users, and the relationship between driving discourtesy and driving stress. To examine courteous and discourteous driving experiences, and to explore the impact of stress associated with such driving experiences. Thirty-eight drivers (20 females) from the Sunshine Coast region volunteered to participate in one of four 1-1.5 h focus groups. Content analysis used the verbatim utterances captured via an Mp3 device. Three themes pertaining to stressful and discourteous interactions were identified. Theme one pertained to the driving context: road infrastructure (eg, roundabouts, roadwork), vehicles (eg, features), location (eg, country vs city, unfamiliar areas), and temporal aspects (eg, holidays). Theme two pertained to other road users: their behaviour (eg, tailgating, merging), and unknown factors (eg, illicit and licit drug use). Theme three pertained to the self as road user: their own behaviours (eg, deliberate intimidation), and their emotions (eg, angry reaction to other drivers, being in control). Driving dis/courtesy and driving stress is a complex phenomenon, suggesting complex intervention efforts are required. Driving discourtesy was reported as being highly stressful, therefore intervention efforts which encourage driving courtesy and which foster emotional capacity to cope with stressful circumstances appear warranted. Copyright © 2018. Published by Elsevier Ltd.

Alcohol mixed with energy drink use among u.s. 12th-grade students: prevalence, correlates, and associations with unsafe driving.

Science.gov (United States)

Martz, Meghan E; Patrick, Megan E; Schulenberg, John E

2015-05-01

The consumption of alcohol mixed with energy drinks (AmED) is a risky drinking behavior, most commonly studied using college samples. We know little about rates of AmED use and its associations with other risk behaviors, including unsafe driving, among high school students. This study examined the prevalence and correlates of AmED use among high school seniors in the United States. Nationally representative analytic samples included 6,498 12th-grade students who completed Monitoring the Future surveys in 2012 and 2013. Focal measures included AmED use, sociodemographic characteristics, academic and social factors, other substance use, and unsafe driving (i.e., tickets/warnings and accidents) after alcohol consumption. Approximately one in four students (24.8%) reported AmED use during the past 12 months. Rates of AmED use were highest among males and white students. Using multivariable logistic regression models controlling for sociodemographic characteristics, results indicate that students who cut class, spent more evenings out for fun and recreation, and reported binge drinking, marijuana use, and illicit drug use had a greater likelihood of AmED use. AmED use was also associated with greater odds of alcohol-related unsafe driving, even after controlling for sociodemographic, academic, and social factors and other substance use. AmED use among 12th-grade students is common and associated with certain sociodemographic, academic, social, and substance use factors. AmED use is also related to alcohol-related unsafe driving, which is a serious public health concern. Copyright © 2015 Society for Adolescent Health and Medicine. Published by Elsevier Inc. All rights reserved.

Electric drives in the vehicle sector. Textbook and manual. 2. enl. ed.; Elektrische Antriebe in der Fahrzeugtechnik. Lehr- und Arbeitsbuch

Energy Technology Data Exchange (ETDEWEB)

Babiel, Gerhard [FH Dortmund (Germany). Fahrzeugtechnik

2009-07-01

The text book under consideration reports on the fundamentals of power generation, energy conversion, induction engine a well as their application in drive systems such as hybrid vehicles and fuel cell vehicles. First of all, current and future energy sources for power train drives are presented and compared with one another. Subsequently, electro-chemical energy stores and energy converters such as fuel cell or double-layer condensers are considered. These energy storages and energy converters are used in electric vehicles and hybrid vehicles. Additionally, the transformer and the central topic of interest 'Electrical Engines' are considered. Not only standard machines (direct current motor, asynchronous motor, synchronous motor, linear motor) will be described but also engines which are applied in future passenger car drives and railway drives (reluctance motor, transverse flow engine, BLDC engine). Drive systems are presented by the example of an electric locomotive and a magnetic levitation transport system (superconducting MAGLEV).

Batu Pahat Driving Cycle for Light Duty Gasoline Engine

Science.gov (United States)

Zainul Abidin, Zainul Ameerul Ikhsan B.; Faisal Hushim, Mohd; Ahmad, Osman Bin

2017-08-01

Driving cycle is a series of data points that represents the vehicle speed versus time. Transient driving cycles involve many changes such as frequent speed changes during typical on-road driving condition [2]. Model driving cycles involve protracted periods at constant speeds. The Batu Pahat Driving Cycle (BPDC) developed to represent the driving pattern of people in a district of Batu Pahat. Based on this driving cycle, it will be a reference to other researchers to study about the gases emission release and fuel consumption by the vehicle on the dynamometer or automotive simulation based on this driving cycle. Existing driving cycles used such as the New European Driving Cycle (NEDC), the Federal Test Procedure (FTP-72/75, and Japan 10-15 Mode Cycle is not appropriate for Batu Pahat district because of different road conditions, driving habits and environmental of developed driving cycle countries are not same [2][14]. Batu Pahat drive cycle was developed for low-capacity gasoline engine under 150 cc and operating on urban roads, rural roads and road around Universiti Tun Hussein Onn. The importance of these driving cycle as the reference for other research to measure and do automotive simulation regarding fuel consumption and gas emission release from the motorcycle for these three type of driving cycle area. Another use for driving cycles is in vehicle simulations [3]. More specifically, they are used in propulsion system simulations to predict the performance of internal combustion engines, transmissions, electric drive systems, batteries, fuel cell systems, and similar components [18]. Data collection methods used in this study is the use of Global Positioning System (GPS). The results obtained are not similar to each other due to differences in congestion on data taken. From the driving cycle graph obtained, such as the average velocity, maximum velocity, the duration and Positive Acceleration Kinetic Energy (PKE) can be determined. In addition, the best

Designing Fatigue Warning Systems: The perspective of professional drivers.

Science.gov (United States)

Meng, Fanxing; Li, Shuling; Cao, Lingzhi; Peng, Qijia; Li, Musen; Wang, Chunhui; Zhang, Wei

2016-03-01

Professional drivers have been characterized as experiencing heavy fatigue resulting from long driving time in their daily work. This study aimed to explore the potential demand of Fatigue Warning Systems (FWSs) among professional drivers as a means of reducing the danger of fatigue driving and to examine their opinions regarding the design of FWSs. Six focus groups with 35 participants and a questionnaire survey with 600 respondents were conducted among Chinese truck and taxi drivers to collect qualitative and quantitative data concerning the current situation of fatigue driving and opinions regarding the design of FWSs. The results revealed that both truck and taxi drivers had a positive attitude toward FWSs, and they hoped this system could not only monitor and warn them regarding their fatigue but also somewhat relieve their fatigue before they could stop and rest. As for warning signals, participants preferred auditory warnings, as opposed to visual, vibrotactile or electric stimuli. Interestingly, it was proposed that verbal warnings involving the information regarding consequences of fatigue driving or the wishes of drivers' family members would be more effective. Additionally, different warning patterns, including graded, single and continuous warnings, were discussed in the focus group. Finally, the participants proposed many other suggestions, as well as their concerns regarding FWSs, which will provide valuable information for companies who wish to develop FWSs for professional drivers. Copyright © 2015. Published by Elsevier Ltd.

75 FR 27662 - Special Conditions: Boeing 747-468, Installation of a Medical Lift

Science.gov (United States)

2010-05-18

... electrical motors, mounted to the rear wall, between the struts. A lifting gear-drive with shafts and gear... OPERATE LIFT DURING TAXI, TAKEOFF, LANDING, OR TURBULENCE. c. AN APPROVED MEDICAL STRETCHER OR WHEELCHAIR... operation. b. Operate the lift. c. Stow the lift for non-operation such as during TTL and turbulence. d...

New Region-Scalable Discriminant and Fitting Energy Functional for Driving Geometric Active Contours in Medical Image Segmentation

Directory of Open Access Journals (Sweden)

Xuchu Wang

2014-01-01

that uses region-scalable discriminant and fitting energy functional for handling the intensity inhomogeneity and weak boundary problems in medical image segmentation. The region-scalable discriminant and fitting energy functional is defined to capture the image intensity characteristics in local and global regions for driving the evolution of active contour. The discriminant term in the model aims at separating background and foreground in scalable regions while the fitting term tends to fit the intensity in these regions. This model is then transformed into a variational level set formulation with a level set regularization term for accurate computation. The new model utilizes intensity information in the local and global regions as much as possible; so it not only handles better intensity inhomogeneity, but also allows more robustness to noise and more flexible initialization in comparison to the original global region and regional-scalable based models. Experimental results for synthetic and real medical image segmentation show the advantages of the proposed method in terms of accuracy and robustness.

Design and Analysis of a Linear Hybrid Excitation Flux-Switching Generator for Direct Drive Wave Energy Converters

Directory of Open Access Journals (Sweden)

Lei Huang

2013-01-01

Full Text Available Linear generators have the advantage of a simple structure of the secondary, which is suitable for the application of wave energy conversion. Based on the vernier hybrid machines (VHMs, widely used for direct drive wave energy converters, this paper proposes a novel hybrid excitation flux-switching generator (LHEFSG, which can effectively improve the performance of this kind of generators. DC hybrid excitation windings and multitooth structure were used in the proposed generator to increase the magnetic energy and overcome the disadvantages of easily irreversible demagnetization of VHMs. Firstly, the operation principle and structure of the proposed generator are introduced. Secondly, by using the finite element method, the no-load performance of the proposed generator is analyzed and composed with ones of conventional VHM. In addition, the on-load performance of the proposed generator is obtained by finite element analysis (FEA. A dislocation of pole alignments method is implemented to reduce the cogging force. Lastly, a prototype of the linear flux-switching generator is used to verify the correctness of FEA results. All the results validate that the proposed generator has better performance than its counterparts.

Determination of power and moment on shaft of special asynchronous electric drives

Science.gov (United States)

Karandey, V. Yu; Popov, B. K.; Popova, O. B.; Afanasyev, V. L.

2018-03-01

In the article, questions and tasks of determination of power and the moment on a shaft of special asynchronous electric drives are considered. Use of special asynchronous electric drives in mechanical engineering and other industries is relevant. The considered types of electric drives possess the improved mass-dimensional indicators in comparison with singleengine systems. Also these types of electric drives have constructive advantages; the improved characteristics allow one to realize the technological process. But creation and design of new electric drives demands adjustment of existing or development of new methods and approaches of calculation of parameters. Determination of power and the moment on a shaft of special asynchronous electric drives is the main objective during design of electric drives. This task has been solved based on a method of electromechanical transformation of energy.

Effects of electro-fishing on galvano-taxis and carcass quality characteristics in sea bass (Dicentrarchus labrax

Directory of Open Access Journals (Sweden)

Edo D’Agaro

2010-01-01

Full Text Available The aim of this study was to investigate the effects of electro-fishing in sea water. We evaluated the feasibility of an electro-fishing system using numerical simulations for laboratory tanks and the open sea and performing a laboratory experiment. A non-homogeneous bi-dimensional electric-field model for marine water and fish based on discrete formulation of electro-magnetic field equations was developed using GAME (geometric approach for Maxwell equations software. Voltage gradients inside the fish and close to the body were determined. Re- sults showed that fish in the open sea and in groups had greater internal voltage differences than did fish in tanks and single fish. Sea bass (length:10 and 30 cm were exposed in laboratory tanks to pulsed direct current (PDC, 25-125 Hz and duty cycle (5-40%. We measured the electro-taxis and tetanus thresholds after electrical exposure. It is significant that these values decreased with increasing the size of fish. No differences were found after electro-fishing on overall appearance, internal and external haemorrhage, standard freshness scoring techniques and carcass quality characteristics

A tethering complex drives the terminal stage of SNARE-dependent membrane fusion

Science.gov (United States)

D'Agostino, Massimo; Risselada, Herre Jelger; Lürick, Anna; Ungermann, Christian; Mayer, Andreas

2017-11-01

Membrane fusion in eukaryotic cells mediates the biogenesis of organelles, vesicular traffic between them, and exo- and endocytosis of important signalling molecules, such as hormones and neurotransmitters. Distinct tasks in intracellular membrane fusion have been assigned to conserved protein systems. Tethering proteins mediate the initial recognition and attachment of membranes, whereas SNARE (soluble N-ethylmaleimide-sensitive factor attachment protein receptor) protein complexes are considered as the core fusion engine. SNARE complexes provide mechanical energy to distort membranes and drive them through a hemifusion intermediate towards the formation of a fusion pore. This last step is highly energy-demanding. Here we combine the in vivo and in vitro fusion of yeast vacuoles with molecular simulations to show that tethering proteins are critical for overcoming the final energy barrier to fusion pore formation. SNAREs alone drive vacuoles only into the hemifused state. Tethering proteins greatly increase the volume of SNARE complexes and deform the site of hemifusion, which lowers the energy barrier for pore opening and provides the driving force. Thereby, tethering proteins assume a crucial mechanical role in the terminal stage of membrane fusion that is likely to be conserved at multiple steps of vesicular traffic. We therefore propose that SNAREs and tethering proteins should be considered as a single, non-dissociable device that drives fusion. The core fusion machinery may then be larger and more complex than previously thought.

The relationship between gas fill density and hohlraum drive performance at the National Ignition Facility

Science.gov (United States)

Hall, G. N.; Jones, O. S.; Strozzi, D. J.; Moody, J. D.; Turnbull, D.; Ralph, J.; Michel, P. A.; Hohenberger, M.; Moore, A. S.; Landen, O. L.; Divol, L.; Bradley, D. K.; Hinkel, D. E.; Mackinnon, A. J.; Town, R. P. J.; Meezan, N. B.; Berzak Hopkins, L.; Izumi, N.

2017-05-01

Indirect drive inertial confinement fusion experiments were conducted at the National Ignition Facility to investigate the performance of the hohlraum drive as a function of hohlraum gas fill density by imploding high-density-carbon capsules using a 2-shock laser pulse. Measurements characterized the backscatter behavior, the production of hot electrons, the motion and brightness of the laser spots on the hohlraum wall, and the efficiency of the hohlraum x-ray drive as a function of gas fill density ρgf between 0.03 mg/cc ("near vacuum") and 1.6 mg/cc. For hohlraums with ρgf up to 0.85 mg/cc, very little stimulated Raman backscatter (SRS) was observed. For higher ρgf, significant SRS was produced and was observed to occur during the rise to peak laser power and throughout the main pulse. The efficiency with which laser energy absorbed by the hohlraum is converted into drive energy was measured to be the same for ρgf ≥ 0.6 mg/cc once the laser reached peak power. However, for the near vacuum case, the absorbed energy was converted to drive energy more efficiently throughout the pulse and maintained an efficiency ˜10% higher than the gas filled hohlraums throughout the main pulse.

Older drivers with cognitive impairment: Perceived changes in driving skills, driving-related discomfort and self-regulation of driving

DEFF Research Database (Denmark)

Meng, A.; Siren, A.; Teasdale, Thomas William

2013-01-01

The results of a previous study indicate that in general, older drivers who recognise cognitive problems show realistic self-assessment of changes in their driving skills and that driving-related discomfort may function as an indirect monitoring of driving ability, contributing to their safe...... drivers may recognise cognitive problems, they tend not to recognise changes to their driving, which may reflect reluctance to acknowledge the impact of cognitive impairment on their driving. Furthermore, the results suggest that driving-related discomfort plays an important role in the self......-regulation of driving among cognitively impaired older drivers. However, it is less clear what triggers driving-related discomfort among cognitively impaired older drivers indicating that it may be a less reliable aspect of their self-monitoring of driving ability....

What drives energy consumers? : Engaging people in a sustainable energy transition

NARCIS (Netherlands)

Steg, Linda; Shwom, Rachel; Dietz, Thomas

Providing clean, safe, reliable, and affordable energy for people everywhere will require converting to an energy system in which the use of fossil fuels is minimal. A sustainable energy transition means substantial changes in technology and the engagement of the engineering community. But it will

Drive Stands

Data.gov (United States)

Federal Laboratory Consortium — The Electrical Systems Laboratory (ESL)houses numerous electrically driven drive stands. A drive stand consists of an electric motor driving a gearbox and a mounting...

Comparing Expert and Novice Driving Behavior in a Driving Simulator

Directory of Open Access Journals (Sweden)

Hiran B. Ekanayake

2014-02-01

Full Text Available This paper presents a study focused on comparing driving behavior of expert and novice drivers in a mid-range driving simulator with the intention of evaluating the validity of driving simulators for driver training. For the investigation, measurements of performance, psychophysiological measurements, and self-reported user experience under different conditions of driving tracks and driving sessions were analyzed. We calculated correlations between quantitative and qualitative measures to enhance the reliability of the findings. The experiment was conducted involving 14 experienced drivers and 17 novice drivers. The results indicate that driving behaviors of expert and novice drivers differ from each other in several ways but it heavily depends on the characteristics of the task. Moreover, our belief is that the analytical framework proposed in this paper can be used as a tool for selecting appropriate driving tasks as well as for evaluating driving performance in driving simulators.

Development of a Cooperative Braking System for Front-Wheel Drive Electric Vehicles

Directory of Open Access Journals (Sweden)

Di Zhao

2018-02-01

Full Text Available Most electric vehicles adopt cooperative braking systems that can blend friction braking torque with regenerative braking torque to achieve higher energy efficiency while maintaining a certain braking performance and driving safety. This paper presented a new cooperative regenerative braking system that contained a fully-decoupled hydraulic braking mechanism based on a modified electric stability control system. The pressure control algorithm and brake force distribution strategy were also discussed. Dynamic models of a front wheel drive electric car equipped with this system and a simulation platform with a driver model and driving cycles were established. Tests to evaluate the braking performance and energy regeneration were simulated and analyzed on this platform and the simulation results showed the feasibility and effectiveness of this system.

Energy conservation through utilization of mechanical energy storage

Science.gov (United States)

Eisenhaure, D. B.; Bliamptis, T. E.; Downer, J. R.; Heinemann, P. C.

Potential benefits regarding fuel savings, necessary technology, and evaluation criteria for the development of flywheel-hybrid vehicles are examined. A case study is quoted in which adoption of flywheel-hybrid vehicles in a taxi fleet would result in an increase of 10 mpg average to 32 mpg. Two proposed systems are described, one involving direct engine power to the flywheel and the second regenerating the flywheel from braking energy through a continuously variable transmission. Fuel consumption characteristics are considered the ultimate determinant in the choice of configuration, while material properties and housing shape determine the flywheel speed range. Vehicle losses are characterized and it is expected that a flywheel at 12,000 rpm will experience less than one hp average parasitic power loss. Flywheel storage is suitable for smaller engines because larger engines dominate the power train mass. Areas considered important for further investigation include reliability of an engine run near maximum torque, noise and vibration associated with flywheel operation, start up delays, compatibility of driver controls, integration of normal with regenerative braking systems, and, most importantly, the continuously variable transmission.

Cognitive problems, self-rated changes in driving skills, driving-related discomfort and self-regulation of driving in old drivers

DEFF Research Database (Denmark)

Meng, Annette; Siren, Anu Kristiina

2012-01-01

Ageing in general is associated with functional decline that may have an adverse effect on driving. Nevertheless, older drivers have been found to show good judgement and to self-regulate their driving, which may enable them to continue driving safely despite functional decline. The process...... of the self-monitoring of driving ability and the awareness of functional decline, and its association with the self-regulation of driving is, however, not fully understood. The aim of the present study was to examine the perceived changes in driving skills, the discomfort experienced in driving, and the self......-related discomfort is an important factor affecting the self-regulation of driving. Finally, the findings indicate that driving-related discomfort functions as an indirect self-monitoring of driving ability and may contribute to the safe driving performance of Danish older drivers....

Study of Solid State Drives performance in PROOF distributed analysis system