WorldWideScience

Sample records for energy henkan gijutsu

  1. Fiscal 1998 research report. Research on energy conversion technology using biomass resources; 1998 nendo chosa hokokusho. Biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Feasibility study was made on construction of the new energy production system by thermochemical conversion or combination of thermochemical and biological conversions of agricultural, fishery and organic waste system biomass resources. This report first outlines types and characteristics of biomass over the world, proposes the classification method of biomass from the viewpoint of biomass energy use, and shows the introduction scenario of biomass energy. The energy potential is calculated of agricultural waste, forestry waste and animal waste as the most promising biomass energy resources, and the biomass energy potential of energy plantation is estimated. The present and future of biochemical energy conversion technologies are viewed. The present and future of thermochemical energy conversion technologies are also viewed. Through evaluation of every conversion technology, the difference in feature between each conversion technology was clarified, and the major issues for further R and D were showed. (NEDO)

  2. Report on a survey in fiscal 1999. Part 2. Survey on the biomass-derived energy conversion technology; 1999 nendo biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Biomass energy is positioned as a promising environment harmonizing energy in the 21st century because it does not break down the CO2 balance in the global scale. The present survey has investigated quantity of biomass resources utilizable as energy resources, investigated and analyzed the biomass-derived energy conversion technology, searched for a promising practically usable technology, and discussed the means to achieve the technological introduction. The foreword chapter describes that now is the good time to recognize importance of and introduce the biomass-derived technology. First and second chapters estimate energy potential and utilizable quantity of wastes-based biomass in Indonesia, Malaysia, the Philippines, and Brazil. Chapter 3 investigates feasibility of methane fermentation and ethanol fermentation as a promising bio-chemical conversion process. Chapter 4 has performed feasibility studies on biomass electric power generation, methanol synthesis by gasification, thermal decomposition and gasification as promising thermo-chemical conversion processes. Chapter 5 proposed a biomass electric power generation system, a biomass-gasified methanol synthesizing system, and a dimethyl ether production system. (NEDO)

  3. FY 2000 report on the results of the survey on the biomass-derived energy conversion technology. III; 2000 nendo biomass shigen wo genryo to suru energy henkan gijutsu ni kansuru chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation to the biomass-derived energy conversion technology which was regarded as promising from the results of the survey already made, the survey was made on the present situation and subjects of the technical development, social needs, energy efficiency, economical efficiency and the future. Studies were conducted on the development of technology for effective biomass utilization and the conceptual design and evaluation of a system for effective biomass utilization. As to the effective biomass utilization technology, the survey was made on the biomass combustion power generation technology/gasification power generation technology, gasification methanol synthesis of biomass, biomass gasification dimethyl ether synthesis, technology of ethanol production by alcohol fermentation via saccharification of biomass, methy-esterification of grease biomass, especially palm oil, and diesel oil production via reformation of by-product glycerin, and energy production from biomass using super- (sub- ) critical reaction. As to the system for effective biomass utilization, the survey was carried out of the regional outline, resource amount and sampling amount, selection of the conversion technology, and economical efficiency of Takatsuki city, Osaka, Shimokawa town, Hokkaido, Yufutsu/Hidaka region, Hokkaido, and Aogaki town, Hyogo. (NEDO)

  4. Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of key technology (energy conversion on technology using chemical reactions); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Yoso gijutsu no kenkyu (kagaku energy henkan gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for energy conversion technology using chemical reactions by the aid of solar energy. The demonstration runs were conducted by a bench-scale unit, which was operated stably for 100h, to produce promising results. The catalyst exhibits stable performance, without showing a sign of deactivation. It is found that the heat pump system works well, without being interfered with accumulated by-products. A heat of approximately 2,100kcal/h is recovered. It is confirmed that steam of 150{degree}C and 200{degree}C is generated from hot water of 80{degree}C and 95{degree}C, respectively. The bench-scale runs show a thermal efficiency of around 10%, which is lower than the target level. However, the runs with hydrogen-occluding alloy attain a process thermal efficiency of 30%. The system in which solar collector and chemical heat pump units are combined is evaluated with respect to its economic efficiency and operability for its eventual commercialization. 6 figs., 2 tabs.

  5. FY 2000 report on the results of the supplementary project for the development of energy utilization rationalization technology. Leading study for the development of high efficiency thermoelectric converter; 2000 nendo energy shiyo gorika gijutsu kaihatsu hojo jigyo seika hokokusho. Kokoritsu netsuden henkan soshi kaihatsu sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    For the purpose of energy conservation and environmental protection by effective utilization of unused waste heat, the R and D of thermoelectric conversion technology were conducted, and the FY 2000 results were summed up. In the investigative study of thermoelectric converting materials, evaluation was made of the materials having a possibility of achieving the target with the element efficiency of 6% and the assumed use temperature domain of 120-330 degrees C. The result of the study indicated that the number of new materials which were made public was increasing, but there were no materials that have evidently practical applicability. In the investigative study of element manufacturing technology, trial manufacture of element was made in which the investigative results were integrated into the existing 50W element manufacturing technology, and a target of 70W was achieved. In the investigative study of the thermoelectric conversion system for industrial and commercial/residential use, field survey and questionnaire survey were conducted for three fields of iron works, chemical plant and garbage disposal plant. As a result, it was found that there was a large amount of waste heat. By the study of the system conceptional design, it was found out that the output of 40-50kW can be obtained in the system structure suitable for the source of waste heat of iron works, etc. (NEDO)

  6. Report on investigations and studies on chemical conversion of photo-energy; Hikari energy no kagakuteki henkan ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This paper summarizes problems in utilization of solar energy, their solutions, features, the currently achieved results, and prospects. With regard to water decomposition using semiconductors, simultaneous generation of hydrogen and oxygen has already been achieved, and there is high possibility of raising the efficiency by improving catalysts. Water decomposition using metal complexes has acceleration of charge isolation as the largest problem, whose prospect of solution is not necessarily bright at the present time. Photo-catalytic reaction is a field to be discussed as one means of developing a new synthesizing method from the viewpoint of organic synthetic chemistry. Conversion into electric energy that uses a photovoltaic process has high efficiency, and is a field to be noted. In photo-energy conversion by means of photo-synthesis, living organisms performing hydrogen production at high efficiency have been discovered. Important studies include the studies in terms of chemical engineering using these living organisms, improvement of breeds by gene manipulations, and studies that utilize living organisms or part of the constituting components. (NEDO)

  7. Wind energy technology : from the past to the future; 20 seiki ni okeru furyoku riyo gijutsu no henkan. Furyoku hatsuden : kako kara mirai e

    Energy Technology Data Exchange (ETDEWEB)

    Ushiyama, I. [Ashikaga Institute of Technology, Tochigi (Japan)

    2000-01-20

    Windmills are one of the oldest prime movers and have been used for more than 700 years in Europe. The transition from low speed windmills for grain grinding and water pumping to high speed wind turbines for electric power generation had occurred at first, reviews the windmill technologies and the researchers before 20{sup th} century. Then describes the back ground of how the wind power generator has existed and how the four pioneers developed their wind power generator. The historical developments of windmills to wind turbines in this century are studied focusing mainly on Danish activities. Then, the effort of the development of large wind turbine such as Smith-Putnum's first MW machine in U.S.A. and other mammoth machine concept are introduced. The new concept machines such as Savonius and Darrieus wind turbines in 1920s to 1930s are also explained. Finally, the novel technologies of wind turbine covering larger machines, variable speed generators, special wing sections for wind turbines, theoretical analysis method of wind turbine performance, offshore wind turbines, and wind turbine control technologies are stated. (author)

  8. Development of hydriding alloys with multi-functionally-graded properties and their applications to energy conversion devices; Keishagata fukugo kino wo hyomen ni motsu suiso kyuzo gokin no kaihatsu to energy henkan gijutsu eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    Suda, S; Kadoma, H; Nagamoto, H; Okura, T [Kogakuin University, Tokyo (Japan)

    1997-02-01

    This paper describes the formation of fluoride layer on the surface of hydriding alloys. The fluoride formation reaction consists of a reduction removal process of surface oxide and a fluorination process. Specific surface area of alloy grains can be increased by the hydrogenation reaction in the surface layer accompanied with the removal of surface oxide, which results in easier permeation of molecular hydrogen into fluoride layer. During the fluorination process, a large amount of Ni in the alloy components is eluted, which results in the reduction of Ni distribution immediately under the fluoride layer in the alloy. Consequently, collector sites near the surface are reduced, and conductivity among alloy grains is degraded. To enhance the hydrogen collector sites, specific surface area of alloy grains can be increased by controlling the pH value of fluorination treatment solution in a given range. Moreover, performance of fluoride layer can be advanced by electrochemically dispersing metal Ni in the fluoride layer using Ni complex ion mixed in the treatment solution. 2 refs., 3 figs.

  9. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A phenomenon of excess heat generation through the electrolysis of heavy water using palladium metals as electrode can be recognized as new hydrogen energy. Its mechanism has been investigated for four years since FY 1993. In FY 1993, the New Hydrogen Energy Demonstration Research Center and the New Hydrogen Energy Demonstration Laboratory were organized, and the research was initiated. For the excess heat generation demonstration model tests, two types of electrolysis experimental units were constructed, and the Pd/D-based electrolysis experiments were initiated. For the measurements of excess heat using an open type electrolysis cell, there were rather large errors ranging from -13% to +7%. It is necessary to improve the accuracy. For the measurements using a fuel cell type electrolysis cell, generation of the excess heat ranging from 0% to 6% was observed. For the validity of this, it is required to confirm the long-term stability of calibration and cell components. For the correlation between the increase in absorbing rate and the generation of excess heat, results of 2 to 3% lower were obtained. 28 refs., 89 figs., 26 tabs.

  10. WE-NET. Substask 4. Development of hydrogen production technologies; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 4. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work), researches were conducted aiming at the establishment of a hydrogen production technology through electrolysis of polymer electrolyte solution. In fiscal 1998, element technologies were developed for the development of high-efficiency/large-capacity water electrolyzing plants using electrodeless deposition and hot pressing, research and investigation of optimum operating conditions were conducted, and a service plant conceptual design and a polymer electrolytic membrane were developed. In addition, literature was searched for the current state of ion exchange membranes and water electrolysis, both indispensable for the hydrogen production technology discussed in this paper. In the field of lamination of large cells (electrode surface:2500cm{sup 2}), an excellent energy efficiency level exceeding 90% set as the target for a large laminated cell performance test was achieved - 92.6% by electrodeless deposition and 94.4% by hot pressing. As for polymer membranes capable of resisting high temperatures, a membrane with an ionic conductivity of 0.066S/cm at 200 degrees C was newly developed. (NEDO)

  11. FY 1995 development of fluorinated hydriding alloys with multi functional and functionally-graded surface and their application to energy conversion devices; 1995 nendo keishagata fukugo kino wo hyomen ni motsu suiso kyuzo gokin no kaihatsu to energy henkan gijutsu eno oyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The project is the extended researches of a fluorination technique invented by the project leader (Suda) for improving the surface properties and characteristics of conventional hydriding alloys from the following viewpoints; (1) To investigate the roles of fluorinated surface during hydrogen uptake both in the gas-solid and the electrochemical reactions. (2) To elucidate the factors which increase the protective nature of the surface. (3) To develop a material design procedure for synthesizing thin layer of functionally graded surface which is composed of metallic Ni and the fluoride compound. (1) An advanced fluorination technique was developed to incorporate metallic Ni in the surface fluoride layer. (2) Metallic Ni was successfully distributed in a functionally graded manner in the Surface fluoride layer. (3) Through the technique developed, the following properties and characteristics were successfully donated in the fluorinated hydriding alloys such as AB{sub 5}, AB{sub 2}, and AB; (3-1)Surface oxides which act as the resistant layer to the hydrogen up take was completely eliminated to result in the enhancement of the initial activation characteristics. (3-2) Hydrogen selectivity and permeability was greatly improved. (3-3) Surface protective nature against the impurity gases and contaminants was significantly improved. (3-4) Initial activation characteristics both in the gas-solid and the electrochemical reactions were distinguishably improved. (3-5) Fluorinated surface was found to function as the catalyst for a methanation reaction between the CO{sub 2} gas adsorbed over the fluorinated surface and the monatomic hydrogen absorbed in the metal lattice of the crystalline structure of the hydriding alloys. (4) A technique was developed for increasing the specific surface area and decreasing the specific surface diameter of the fluorinated hydriding alloy articles. (NEDO)

  12. Achievement report for fiscal 1998 on development of wide-area energy utilization network system. Eco-energy urban system (Research of systematization technology and evaluation technology out of energy system designing technology researches); Koiki energy riyo network system kaihatsu (eko energy toshi system) 1998 nendo seika hokokusho. Energy system sekkei gijutsu no kenkyu no uchi system ka gijutsu hyoka gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    For the realization of urban society respecting enhanced energy efficiency and environmental protection, cities and surrounding industrial facilities are investigated for the development of element technologies involving energy recovery, conversion, transportation, storage, delivery, utilization, etc., and for the compounding of urban energy systems. In the study of the effect of introduction, assumption is made of delivery of heat to an urban heat accumulation district from a plant equivalent to a district air-conditioning system which is covered by the existing technologies. Also assumed are the delivery of exhaust heat to the said plant utilizing eco-energy element technologies and the replacement of existing technologies by eco-energy element technologies. Comparison is established in terms of energy efficiency, environmental protection, and economy, and then it is found that the eco-energy element technologies for the utilization of exhaust heat are in all cases superior to the conventional technologies as far as energy efficiency and environmental protection are concerned. It is found, however, that they are inferior from the economic viewpoint. The energy efficiency technology in heat transportation is superior to the existing technology in energy efficiency and environmental protection but roughly equal to the existing ones in economy. (NEDO)

  13. Report on survey/research on energy-related elementary techniques; Energy kanren yoso gijutsu ni kansuru chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The survey/research project is implemented for establishing environment-compatible energy systems in urban areas by constructing wide-area heat supply networks to exchange energy among cities. This project studies, taking Kanagawa Pref. as the model area, distributions of unutilized energy sources, and possibilities of their utilization for heat supply. There are large quantities of unutilized energy, including waste heat from power plants, general works and cleaning works, and low-temperature waste heat from, e.g., sewage and pumping systems. The district air conditioning promotion areas are selected from those consuming large quantities of heat energy in the prefecture, and their characteristics are grasped. The effects of the networks on total energy consumption of the entire prefecture are estimated for the cases of introducing the district air conditioning systems or wide-area heat supply networks in these selected areas. Introduction of optimum advanced heat utilization systems in stereotyped areas is also considered, in order to predict the effects of introduction of wide-area heat supply networks. (NEDO)

  14. Fiscal 1999 survey report on survey of long-term strategy on energy technology. Long-term energy technological strategy survey (Long-term energy technological strategy survey); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (choki energy gijutsu senryaku chosa))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To enhance still more effectively the research and development of energy-related/environmental technologies, research and development strategies have to be worked out from a long-term view point and policy resources such as investment in research and development should be optimally distributed after clarifying and defining the course to follow toward the achievement of research and development goals. This project aims to conduct studies, and to show the course to follow in the future, towards the establishment of a long-term energy technological strategy by investigating energy systems for around 2050, interim energy systems at the intermediate stage, and innovative energy technologies for realizing such energy systems. In Chapter 1, the position of the survey and its purpose and prerequisites are shown. In Chapter 2, the history of social and economic conditions surrounding energy/environmental technologies and of energy situation up to the present time is compiled, and the outlook is analyzed and predicted. In Chapter 3, formulation of a long-term energy technological strategy is discussed. In Chapter 5, how to embody such a strategy is shown. (NEDO)

  15. Fiscal 1999 survey report on long-term energy technological strategies and the like. Long-term energy technological strategy survey (Medium-term energy technological strategy survey); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (chuki energy gijutsu senryaku chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Energy strategies to be implemented under the New Sunshine Program by around 2010 have been compiled, with nation's industrial technological strategies, long-term energy outlook, and the like taken into consideration. The present survey aims to work out medium-term energy technological strategies. In Chapter 2, by conducting studies on the state of energy strategies in the national industry technological strategies as primarily compiled, long-term energy supply and demand outlook, and the history so far of the New Sunshine Program, and social conditions surrounding energy/environmental technologies and energy conditions are arranged in order and then analyzed with a view to deriving social needs. In Chapter 3, in view of the derived social needs, medium-term energy technological strategies are broken down into strategic target details, based on the important regions and major and minor strategic targets of the national industry technological strategies. In Chapter 4, medium-term energy technological strategies are worked out. In Chapter 5, 'basic ideas,' 'measures for promoting technology development,' 'return of the fruits to society' are mentioned as the methods of realizing the strategies. In Chapter 6, surveys and researches are summarized, and future development is predicted. (NEDO)

  16. Fiscal 1999 survey report on long-term energy technological strategies and the like. Long-term energy technological strategy survey (Medium-term energy technological strategy survey); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (chuki energy gijutsu senryaku chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Energy strategies to be implemented under the New Sunshine Program by around 2010 have been compiled, with nation's industrial technological strategies, long-term energy outlook, and the like taken into consideration. The present survey aims to work out medium-term energy technological strategies. In Chapter 2, by conducting studies on the state of energy strategies in the national industry technological strategies as primarily compiled, long-term energy supply and demand outlook, and the history so far of the New Sunshine Program, and social conditions surrounding energy/environmental technologies and energy conditions are arranged in order and then analyzed with a view to deriving social needs. In Chapter 3, in view of the derived social needs, medium-term energy technological strategies are broken down into strategic target details, based on the important regions and major and minor strategic targets of the national industry technological strategies. In Chapter 4, medium-term energy technological strategies are worked out. In Chapter 5, 'basic ideas,' 'measures for promoting technology development,' 'return of the fruits to society' are mentioned as the methods of realizing the strategies. In Chapter 6, surveys and researches are summarized, and future development is predicted. (NEDO)

  17. Experimental model for architectural systematization and its basic thermal performance. Part 1. Research on architectural systematization of energy conversion devices; Kenchiku system ka model no gaiyo to kihon seino ni tsuite. 1. Energy henkan no kenchiku system ka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Sunaga, N; Ito, N; Kimura, G; Fukao, S; Shimizu, T; Tsunoda, M; Muro, K [Tokyo Metropolitan University, Tokyo (Japan)

    1996-10-27

    The outline of a model for architectural systematization of natural energy conversion and the experiment result on the basic thermal performance in winter are described. The model is about 20 m{sup 2} in floor space. Foam polystyrene of 100 mm and 200 mm thick was used for the outer wall as heat insulating materials. The model has a solar battery and air conditioner and uses red brick as a heat reservoir. An experiment was made on seven modes obtained when three elements (heating, heat storage, and night insulated door) are combined. The information obtained by the experiment showed that a model for architectural systematization has high heat insulation and tightness and can be used as an energy element or an evaluation model for architectural systematization. In this model for architectural systematization, the power consumption of an air conditioner in winter can be fully supplied by only the power generation based on a solar battery. In an architectural element, the heating energy consumption can be remarkably reduced and the indoor thermal environment can be greatly improved, by the combination of a heat reservoir and night heat insulated door. 1 ref., 6 figs., 3 tabs.

  18. Survey of the energy use rationalization freon decomposition technology (public use); Energy shiyo gorika freon bunkai gijutsu chosa. (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper made a research survey of a technology to decompose the recovered CFC (specified freon) in which energy efficiency is high and no hazardous materials such as dioxin are generated. As to the technology to decompose specified freon, the high frequency plasma method, the cement kiln method and the combustion method are at the stage of the demonstration test and close to the commercialization. The catalyst method has finished the basic test and is at the stage of a pilot plant. Besides, there are the supercritical water decomposition method, the ultraviolet decomposition method, etc., but they are at the stage of the fundamental research. Mechanisms of the dioxin generation and the suppression of dioxin generation in case of incinerating waste mixed with halide have been made clear. In the fundamental test, conditions were obtained under which the freon decomposition rate of more than 99.99% is attained by the combustion of a mixture of industrial waste and freon using the combustion method, and measures for reduction in hazardous materials such as dioxin were expected to be taken. In the catalyst method, the result obtained was the decomposition rate of more than 99.99% and the catalyst life of more than 1000 years, and its practicality was confirmed. 43 refs., 97 figs., 29 tabs.

  19. Comparative analysis of thermal storage cooling and storage battery cooling using photovoltaic generation. Part 2. Research on architectural systematization of energy conversion devices; Taiyoko hatsuden ni yoru chikunetsu reibo to chikuden reibo ni tsuite. 2. Energy henkan no kenchiku system ka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Ito, N; Kimura, G; Fukao, S; Shimizu, T; Sunaga, N; Tsunoda, M; Muro, K; Yamanaka, S [Tokyo Metropolitan University, Tokyo (Japan)

    1996-10-27

    For use in energy self-sufficient buildings, a system was studied capable of retaining for its own use the excess of power produced by a photovoltaic power generation system without releasing it to the commercial system. Summertime cooling was considered. The storage battery cooling system was provided with two solar cell systems and, in the daytime, one was used for cooling and the other for charging batteries for nighttime cooling. In the cold heat storage cooling system, cold heat accumulators (red bricks) were provided in the wall and floor, and under the floor, and the floor was a grating for proper ventilation between the room and underfloor space. With the solar cell-driven air conditioner out of operation, cold heat was fed to the room from the underfloor cold heat accumulators by a fan. In storage battery cooling, solar power covered 60% of what the air conditioner used. In the presence of sufficient power in storage, the air conditioner stayed on at night without buying commercial power, when the room temperature was 25{degree}C. In the cold heat accumulation cooling, 50% of the air conditioner power consumption was covered by solar power. It is recommended to install cold heat accumulators not in the room but in a separate space, such as the underfloor space, where they are exposed to the cooling cold air direct from an air conditioner for future retrieval of cold heat. 2 refs., 9 figs., 3 tabs.

  20. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - material technology field (nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bunya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the nonferrous metal field relating to the FY 1999 long-term energy technology strategy. The needs for electronics products are increasing toward the 21st century. Domestically the competition with other countries in enlarging the market share has been intensifying. At the same time, the smaller the size of device becomes, the more the barriers in technology to be overcome increase. In the development of Si wafer to cope with such a situation, there are a lot of problems to be broken down in liaison with industry/government/university. Compound semiconductors are higher in speed than Si, and have a marked feature of producing light, but are difficult in crystal growth. It was in the past 20 years that the development of commercialization technology has rapidly advanced. Compound semiconductors are indispensable as a device in the energy problem which strongly influences the global environment. In the U.S., for the military use, a policy for upbringing national industries has been carried out since 1993. The role of compound semiconductor materials playing as the fundamental industry which supports the semiconductor industry and system industry as the nation's core industries is important even in Japan the same as in the U.S. (NEDO)

  1. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - material technology field (nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bunya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the nonferrous metal field relating to the FY 1999 long-term energy technology strategy. The needs for electronics products are increasing toward the 21st century. Domestically the competition with other countries in enlarging the market share has been intensifying. At the same time, the smaller the size of device becomes, the more the barriers in technology to be overcome increase. In the development of Si wafer to cope with such a situation, there are a lot of problems to be broken down in liaison with industry/government/university. Compound semiconductors are higher in speed than Si, and have a marked feature of producing light, but are difficult in crystal growth. It was in the past 20 years that the development of commercialization technology has rapidly advanced. Compound semiconductors are indispensable as a device in the energy problem which strongly influences the global environment. In the U.S., for the military use, a policy for upbringing national industries has been carried out since 1993. The role of compound semiconductor materials playing as the fundamental industry which supports the semiconductor industry and system industry as the nation's core industries is important even in Japan the same as in the U.S. (NEDO)

  2. Research and development of utilization technology of solar thermal energy system for industrial and other use. International joint technology development for solar energy utilization systems; Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for international joint technology development for solar energy utilization systems. The joint study with an Indonesian research institute takes a model of lumber drying plant for the design and feasibility study. All the parts it needs are technically available in Indonesia, except carbon fiber sheets and electronic devices for controlling purposes. The drying cost is higher than that of a plant which procures charge-free wood fuel, but lower than that of a plant which procures fuel at 30$/t. A cacao drying plant model is also studied. The feasibility study shows that the initial investment for the blowing-up model is much higher by 60% to 100% than that for the conventional plant. Its fuel cost is lower by 11% than that of residual oil but 27% higher than that of wood. 4 figs.

  3. Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

  4. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Iron and steel technology field; 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) (tekko gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a steel technology field. Japanese steel industry should correspond to requirements of the international economic society as the top runner. Although it is now difficult to suppose a basic technology innovation, stable supply of basic materials is necessary for peripheral industries. The basic raw material technology is the basis of domestic and overseas socio- economic activities. The technology development support system to retain the world-wide leadership of Japanese industries is a strategic issue. Preparation of cooperative R and D bases of industry, academia and government along a national policy is important. Strong promotion of such national projects is also essential as global environment problem, positive use of advanced information tools, development of technologies and products of unexplored fields, and development of new products and demand creation according to social needs. Such measures along social requirements are also important as raw material development to double an energy efficiency, and the policy and system to construct a recycling society and living spaces. (NEDO)

  5. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Machine industry technology field (Semiconductor equipment); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) kikai sangyo gijutsu bun'ya (handotai seizo sochi bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a semiconductor equipment field, viewing until 5-10 years after. For the future semiconductor industry, the favorable cycling of creation of new demands through performance improvement, and further technology innovation through market expansion is essential absolutely. Since technology development is followed by investment, not only the performance of each equipment but also the higher productivity and cost balance of the whole factory are essential. Self-intelligent function and networking are thus necessary for the equipment. As measures for environment preservation and energy saving, such innovative technologies are required as recycling, reuse, reaction process improvement and alternative technology. Because of diverse final products and a short life time of products, a large-scale collective investment is becoming difficult. A mini-line sequential investment production system according to demand scales is under investigation. Some issues such as micro-technology, realization of 300mm wafer, modularization, CIM, reliability and standardization are also described. (NEDO)

  6. Fiscal 1999 research report. Research on the long-term energy technology strategy (Basic research on the industrial technology strategy (Material technology field)); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This research clarifies the future social issues and targets of industrial technology in a material field including metal, inorganic, organic, polymer and fiber materials, and proposes the strategy for achieving such targets, based on research on changes in science and technology trend (technical innovation), and analysis on present and future industrial and technical competition powers. The future basic technologies for enhancing such competition powers are as follows: (1) Resource/energy-saving production process, (2) Design/evaluation technology for fine textures or in an atomic level, (3) Divergence toward high-purity and composite materials, (4) Improvement of a functionality, (5) Improvement of surface treatment technologies, and (6) Development of new materials and production technologies by using computer. The following 5 strategies are proposed based on the common understanding that the Japanese material industry achieves the best material technology innovation in the world by 2010: (1) Material technology strategy, (2) Strong cooperation among the industry, university and government, (3) Preparation of an intellectual base and a standardization strategy, (4) Reform of intellectual property rights, and (5) Resource strategy. (NEDO)

  7. Report on the FY 1999 survey for making a data book related to new energy technology development. Trends of solar energy utilization, waste power generation, clean energy vehicle, geothermal power generation, clean coal technology, other new energy technology and new energy technology development; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Taiyonetsu riyo, haikibutsu hatsuden, clean energy jidosha, chinetsu hatsuden, clean coal technology, sonota no shin energy gijutsu, shin energy gijutsu kaihatsu kanren doko

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper collected/arranged the most up-to-date data made public in the new energy technology field. As to the solar energy utilization, the utilization is on the decrease with the beginning of the 1980s as a peak, and the solar systems introduced in FY 1998 totaled 15,000 and the water heaters 56,000. The waste power generation is showing a steady growth both in the general use and in the industrial use, and the introduction of 5 million KW is expected for FY 2010. The sale of the hybrid car started at the end of 1997, and the subjects are the price/performance/fuel supply system. Concerning the geothermal power generation, 497,000 KW and 36,000 KW were introduced for business use and non-utility use, respectively. Japan ranks sixth among nations of the world. Relating to the coal liquefaction, the pilot plant (PP) of Japan's original bituminous coal liquefaction NEDOL process finished operation in 1998, and the construction of technology package, international cooperation, etc. are being conducted. About the coal gasification, the construction of demonstrative equipment and operation are planned during FY 2002 - FY 2007, making use of the PP achievements of IGCC. In regard to the biomass-based waste power generation, the lignocellulose system is large in potential quantity. As to the hydrogen energy, the WE-NET project entered Period II. With respect to the ocean thermal energy conversion, the demonstrative study started. In relation to the wave power generation, a small size of approximately several hundred W was commercialized. (NEDO)

  8. Fiscal 1998 research report. Research cooperation on car energy and environmental technology based on ITS technology in China; 1998 nendo seika hokokusho. Chugoku ni okeru ITS gijutsu wo mochiita jidosha energy kankyo gijutsu ni kansuru kenkyu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This research aims at preparation of the car energy/environmental vision based on ITS (intelligent transport system) technology in China, enhancement of the transport planning ability of Qinghua University, and promotion of effective energy use in China. The following activities were carried out concretely: Survey on the actual traffic situation by Qinghua University, analysis of environment deterioration factors based on the survey result, estimation of a traffic environment improvement effect, study on traffic flow simulation technique based on traffic engineering, and study on traffic planning technique. As the diffusion strategy of ITS along Chinese circumstances, standardization and improvement of a multi- modal traffic system, navigation and its application system, and ETC (electronic toll collection) system are promising. Expectation for Japan and Japanese roles are as follows: Improvement of signal control, provision of information systems such as navigation, discussion on ITS technology such as ETC with Chinese specialists, and feasibility study on introduction of ITS technology for every Chinese district. (NEDO)

  9. Collection of outlines of Sunshine Program achievement reports for fiscal 1989. Solar energy (Light utilizing technology and heat utilizing technology); 1989 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1990-04-01

    Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the research on the practical application of new-type solar cells; research on the practical application of amorphous solar cells; research and development of solar cell evaluation systems; research and development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and research and development of photothermal hybrid photovoltaic power systems. Collected concerning heat application technologies are the research and development of solar thermal energy systems; development of practical application technologies for solar systems for industrial use etc.; and cooperative projects between Japan and Australia etc. on solar energy technologies. (NEDO)

  10. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Part 1. Technology strategy by field - material technology field (fine ceramics technology field); 1999 nendo choki energy gijutsu senryaku ni kansuru chosa. 1. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (fine ceramics gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the fine ceramics technology field relating to the FY 1999 long-term energy technology strategy. The fine ceramics industry is a new industry for which the future development is expected. It has far-reaching effects on other industries. Japan has the advantage over other countries. As subjects to remarkably develop the industry, needed are the long-term basic preparation which promotes technology innovation such as the promotion of the fundamental/creative R and D, construction of an industry/university liaison system, and arrangement of the intellectual base. Preparation of the competitive environment and promotion of policies paying attention to the market are needed which make the development under the private control by creative study/corporate activities possible. Also important are the demonstration of leadership and secure international competitive force in the light of Japan's international position. For the private-control development, the role and course of various groups should be made clear from a long-term aspect. It is desirable that university/government will newly develop innovative technology, and industry will make the present technology force more developmental and competitive. Support from the nation is requested for researches large in scale. (NEDO)

  11. Hydrogen energy technology development conference. From production of hydrogen to application of utilization technologies and metal hydrides, and examples; Suiso energy gijutsu kaihatsu kaigi. Suiso no seizo kara riyo gijutsu kinzoku suisokabutsu no oyo to jirei

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-02-14

    The hydrogen energy technology development conference was held on February 14 to 17, 1984 in Tokyo. For hydrogen energy systems and production of hydrogen from water, 6 papers were presented for, e.g., the future of hydrogen energy, current state and future of hydrogen production processes, and current state of thermochemical hydrogen technology development. For hydrogen production, 6 papers were presented for, e.g., production of hydrogen from steel mill gas, coal and methanol. For metal hydrides and their applications, 6 papers were presented for, e.g., current state of development of hydrogen-occluding alloy materials, analysis of heat transfer in metal hydride layers modified with an organic compound and its simulation, and development of a large-size hydrogen storage system for industrial purposes. For hydrogen utilization technologies, 8 papers were presented for, e.g., combustion technologies, engines incorporating metal hydrides, safety of metal hydrides, hydrogen embrittlement of system materials, development trends of phosphate type fuel cells, and alkali and other low-temperature type fuel cells. (NEDO)

  12. Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

  13. Fiscal 1993 international joint projects under New Sunshine Program. Surveys of bilateral cooperation and solar energy technology; 1993 nendo kokusai kyoryoku jigyo nikokukan kyoryoku taiyo energy gijutsu ni kakawaru gijutsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    Concerning bilateral projects, overseas surveys were conducted about Japan-Australian and Japan-US technical cooperation. Concerning technological development, information was collected at the Solar World Congress of the International Solar Energy Society (ISES), and information was collected and opinions were exchanged at the 15th International Conference on Amorphous Semiconductors. A survey was conducted of Russia's development of solar cells and of their performance evaluation, and an overseas survey was conducted of the development of spaceborne photovoltaic power generation system practicalization technology. Surveys were conducted of international joint projects for the development of photovoltaic power generation system practicalization technology in Europe and the US. Overseas surveys were conducted of international joint projects concerning the development of photovoltaic power generation system practicalization technology, and a survey was conducted of the research and development of photovoltaic power generation in the US and of the state of introduction and diffusion of the same. A survey was also conducted of the state of element technology development for solar energy utilization in Europe. (NEDO)

  14. FY 2000 report on the results of the technology development of energy use reduction of machine tools, etc. Technology development of environmental load reduction related to water soluble lubricating oil, etc. (R and D of low energy coolant degradation prevention technology and waste liquid processing technology); 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Suiyosei junkatsuyu ni kakawaru kankyo fuka teigen nado gijutsu kanri (tei energy coolant fuhai boshi gijutsu oyobi haieki shori gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The R and D were carried out on a system by which the long life of coolant of machine tools can be achieved and a system to process waste efficiently, economically and with less environmental loads, and the FY 2000 results were summed up. In the R and D of a system to prevent degradation of low energy coolant, measurement was made of effects of the degradation prevention system at a laboratory level, and it was found out that propagation of bacteria causing the degradation can be prevented with pH kept high. Further, it was admitted that the alkali effect on metal formability was not very much. As to the coolant processing, in the present situation, most of the coolant is taken back by industrial waste processing dealers. So, the development of the low energy waste liquid processing system is earnestly desired. In the R and D of the low energy waste liquid processing system, test on characteristics evaluation was conducted about each method of systems. Subjects to be improved/solved were extracted such as the point that volatile organic matters are included in condensed water after evaporation of waste liquid and there seems to be a possibility of needing the secondary processing. (NEDO)

  15. Collection of outlines of Sunshine Program achievement reports for fiscal 1988. Solar energy (Light utilizing technology and heat utilizing technology); 1988 nendo sunshine keikaku seika hokokusho gaiyoshu. Taiyo energy (hikari riyo gijutsu / netsu riyo gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1989-04-01

    Collected concerning the research and development of photovoltaic power systems are the basic research on solar cells; research and development of new-type photovoltaic power systems; and research and development of amorphous solar cells. Collected concerning the development of technologies for the practical application of photovoltaic power systems are the experiment, refining, and verification of low-cost silicon; experiment, fabrication, and verification of solar panels; research on the practical application of high-efficiency crystal-based solar cells; research and development of amorphous solar cells; research and development of solar cell evaluation systems; development of peripheral technologies; research and development of photovoltaic power-aided systems; research and development of centralized photovoltaic power systems; and development of photothermal hybrid type photovoltaic power systems. Collected concerning heat-utilizing technologies are the research and development of solar thermal electric power generation systems; research and development of solar air-conditioners and hot water supply systems; and development of practical application technologies for industrial solar systems. Collected also are international cooperative projects on solar energy technologies. (NEDO)

  16. Worldwide clean energy system technology using hydrogen (WE-NET). subtask 9. Investigation of innovative and leading technologies; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 9. Kakushinteki sendoteki gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The WE-NET Project is a long-term project designed to ensure that an energy network technology using hydrogen becomes a reality not later than 2020. So the project cannot remain effective unless constant efforts are made to foresee future trends of technology and optimize it as the making of entire system for the project. In this project, new technologies which are not up for development are also investigated. Their feasibility should be studied, if necessary. From the foregoing point of view, new technologies are studied, collected and evaluated. Thus, useful suggestions and proposals may be made as to the course for the project to follow, as well as its research and development. Proposals highly evaluated up to FY 1995 are the hydrogen-oxygen internal-combustion Stirling`s engine, hydrogen production by solid oxide electrolysis, magnetic refrigeration technology for liquefaction of hydrogen, solar thermal hydrogen production with iron sponge technology, and hydrogen producing technology with photocatalyst. Conceptual investigation themes in FY 1996 are the hydrogen internal-combustion Stirling engine, solar thermal hydrogen production, phototransformation process, and high-temperature steam electrolysis. 9 figs., 54 tabs.

  17. Research report of FY 1997 on the industrial science and technology development. Technology development of super-metal (technology development of nano-amorphous structural control materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (nano-amorphous kozo seigyo zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Research and development of the innovative metals have been conducted, by which the weight reduction of members can be done by drastically improving the strength compared with conventional metals. For the high-rate cluster deposition and super plastic forming technologies, research and development of aluminum-based light-weight materials have been conducted, which provides excellent strength, toughness, and super plastic formability at room temperature. For the high-density energy utilization and control technology (amorphous-A), super-metals have been investigated as high dew point and corrosion resistance materials used for waste incinerators operated under the very severe conditions. These are expected to be applied to the apparatuses and equipment due to their excellent properties. For the controlled cooling technology (amorphous-B), super-metals with excellent soft magnetic characteristics and degree of shape freedom have been investigated for high performance and high efficiency devices including electric/electronic/communication devices, power transmission devices, and various industrial devices and parts. These are expected to contribute to the creation of new markets and the improvement of international competitive force. 123 refs., 160 figs., 33 tabs.

  18. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). The R and D aims at establishment of observation/manipulation technology of atoms and molecules as common basic technology in various industrial fields such as new material, electronics, bio-technology and chemistry. The R and D thus aims at establishment of observation/manipulation of solid surfaces and DNA organic molecules, formation of fine structures of atomic surface arrangement, and calculation/ simulation for predicting a reaction theorem of atom and molecule surfaces. In fiscal 1997, research was made on improvement and development of computer simulation environment, and description of an excited state of electrons by Green function. Establishment of a construction method and computation code is under investigation for pseudo- potential dependent on excitation energy. Survey was made on research trends of the atom technology by visiting overseas academic societies and institutions. International Symposium on Atom Technology was also held in Tokyo in Nov. 1997

  19. Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Survey of natural gas technology trend); 2000 nendo choki energy gijutsu senryaku nadoni kansuru chosa hokokusho. Choki energy gijutsu senryaku chosa (tennen gas gijutsu doko chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In search of new technical tasks involving the supply, transportation, and utilization of natural gas, a survey is conducted of the trend of natural gas supply and demand, trend of development of related technologies, and their impact on the market. After natural gas matters are outlined and definition and classification are established, investigations are conducted into natural gas production and the trend of new natural gas consuming countries supposedly to affect the natural gas supply and demand situation. Taken up as relevant technologies are cogeneration, natural gas powered automobiles, fuel cells, GTL (gas to liquid) technology, and micro gas turbines. These technologies are examined from the viewpoints of environmentally-friendliness and energy conservation feature, and then tasks to discharge are proposed in the fields of technology development, operation, and fuel. For natural gas powered automobiles, vehicular performance improvement and the conformability and standardization of high-pressure parts and components are taken up in the field of technology development, and the introduction and augmentation of quick fillers for natural gas and increase in the number of natural gas supply stations are taken up in the field of operation. Concerning fuel cells, in the field of fuels to be fed to the same, technologies of hydrogen storage and of refining and reforming of oil based fuels are taken up. (NEDO)

  20. Fiscal 1999 survey report. Basic survey on practical application of innovative energy technologies; 1999 nendo kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This survey aims to verify whether recoverable energies can bear the important role of energy source in place of fossil fuels, to probe into problems that may arise in the process of recoverable energy introduction, and to compile suggestions about measures toward their smooth introduction, these by working out an 'ultralong-term world energy supply and demand outlook' valid up to 2100. Various measures to deal with global warming are analyzed by simulation. The study is not to predict what is in store but to metrically describe and present choices and possibilities for the future with a theoretical consistency based on various factors including economic growth, population, demand for energy, magnitude of fossil energy resources, and feasibility and cost of recoverable energies. This study implies that there is not a single, determining policy for solving the global warming problem and that it is important to cope with the problem by resorting to combinations of various means. (NEDO)

  1. Data book on new energy technology in FY 1997. Wind power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Furyoku hatsuden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is an urgent necessity for Japan to promote the technological development and accelerate the introduction and diffusion of new energy. In order to diffuse and enlighten the introduction of new energy technology efficiently, it is necessary to compile various information regarding new energy in a comprehensive and systematic way, and formulate a database. Aiming at the systematic formulation of data on new energy, this survey focuses on the field of wind power generation system (WPS) and provides a collection of the latest published data on WPS, particularly regarding the worldwide installed wind power capacity, support plan and government policies, current situations of WPS market, and major technical characteristics of typical wind turbines. This report consists of the significance of wind energy, world market of wind turbines, government policies, international wind energy development, subsidies for wind energy, procedures of wind turbine system installation, governmental measures for wind energy development, subsidiary companies and organizations, basis of wind energy, and Japan`s wind energy development in 1997

  2. New energy technology development related database construction survey (wind power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (furyoku hatsuden)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To arrange systematic data relating to new energy, the latest published data relating to the wind energy conversion systems have been collected and arranged. For the overview of wind energy conversion system, wind turbines with horizontal axis and vertical axis, specification of wind turbine, and conceptual figure of wind energy conversion systems are illustrated. For the installation examples, introduction development of wind energy conversion systems in the world is described for Japan, the USA, Germany, Denmark, Spain, Sweden, India, and Belgium. For the relevant legislation and support plan, relevant legislation for the introduction of wind energy conversion in Japan, support plan in Japan, and support plans in foreign countries are described. Prices of wind turbines by wind turbine makers in the world, construction cost by Japanese makers, basic term, and subsidiary company and organization are shown

  3. Investigation on innovation of technology development by means of strategic energy intelligence; Energy senryakurontekina approach ni yoru gijutsu kaihatsu no kakushin ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    For the purpose of developing the future innovative energy technology, the paper described a strategic point of view. Effects of the energy issue are remarkable on the next generation and thereafter as seen in the finite of energy resource, global-scale environmental changes, the increasing energy demand, natural/social influences of large-scale technology development. If the technological development is going on in the same way as until now, there will appear limits. Relating to the strategies, to seek what energy should be among the strategies, it is necessary to consider not only global-scale problems but particular conditions in Japan (self-sufficiency, international cooperation, creativity, etc.) Also, wisdom and technique are necessary to attain it. Technological development in a wide sense plays a major role in the energy strategy. Technology innovation must be advanced according to the energy strategy. Integrating ideology into the development of energy technology and selecting therefrom developmental subjects which meet the purpose, required is the construction of the energy system with high flexibility and functionality. Looking at the conventional way of thinking from a different angle and posing a future pull plan, Japan should show leadership to the world. 20 refs., 25 figs., 8 tabs.

  4. Survey on construction of the database for new energy technology development. Cogeneration; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the activity promoting use of new energy, the data related to cogeneration were systematically compiled. For new energy technology, such various policies for introducing new energy are in promotion with a progress of technological development as preparation of subsidy systems, field test business, and support advisory business for introducing new energy. For further effective promotion, integral systematic compilation of various data, and arrangement as basic data are necessary. Such latest announced data in a cogeneration field were collected and compiled as outline of new energy systems, concrete applications, subsidy systems, and approaches to new energy of various countries. Main data items are as follows: trend of cogeneration, outline of system, domestic and foreign concrete applications, prediction data on the use of new energy, overview of domestic and foreign policies for cogeneration, basic terminology, and tables of main related enterprises and organizations. This database is useful for the present activities promoting use of new energy, and preparation of the future vision. 29 figs., 33 tabs.

  5. Data book on new energy technology development in FY 1997. Cogeneration; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Various policies are being implemented in the field of new energy technology in line with progress in technological development. Examples are about assistance mechanism, field test projects and advisory projects to support the introduction of new energy technology. In order to promote the introduction of new energy efficiently, it is necessary to compile the various information regarding new energy in a comprehensive and systematic way, and formulate a basic data set. Among various new energy technologies, cogeneration is discussed in this report. The latest published data on the respective technologies are compiled particularly regarding their overall systems, examples of introduction, assistance mechanisms and state of implementation in foreign countries. Items included in this report are the trend of cogeneration, outline of system, state of introduction, forecast of introduction, overview of policies, basic terms, and related organizations. 9 figs.

  6. FY 1974 report on the results of the Sunshine Project. Technology assessment of hydrogen energy technology; 1974 nendo suiso energy gijutsu no technology assessment seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-04-30

    This is aimed at studying the relation between the technology development of hydrogen energy and the society. In Chapter 1, a meaning of technology assessment was examined. When applying it to the hydrogen energy technology, the paper presented what content it has. In Chapter 2, the needs for hydrogen energy in society were made clear in comparison with the energy supply/demand structure in Japan and characteristics of hydrogen energy. In Chapter 3, the paper showed what kinds of technology are being developed to meet the needs in this society and arranged viewpoints for evaluating the effectiveness of the technology. In Chapter 4, the paper studied the positioning of hydrogen energy technology in the future society, and presented as examples more than one hydrogen energy/system plans which become the base to describe the impact of the technology on the society. If taking technology assessment as a part of the communication activities between the technology development and the society as did in this study, these system plans are something like the ring for people in each field to talk with. In Chapter 5, the study made from each aspect was arranged. (NEDO)

  7. Development of the advanced load leveling air conditioning technology utilizing unutilized energy; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    A heat supply plant utilizing unutilized energy is called for environment-friendly efficient operation including stable heat supply, energy saving, CO{sub 2} emission control and power load leveling. Toshiba developed the optimum operation system for environment-friendly efficient operation considering heat demand prediction and characteristics of a heat supply plant. The demonstration test result showed that this system is effective to reduce power cost of a heat supply plant by nearly 15%. This system was promoted by joint research of NEDO, Heat Pump and Thermal Storage Technology Center of Japan and Toshiba supported by Agency of Natural Resources and Energy, MITI. (translated by NEDO)

  8. Fiscal 1975 Sunshine Project research report. Technology assessment on hydrogen energy technology. Part 2; 1975 nendo suiso energy gijutsu no technology assessment seika hokokuksho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-31

    This research assesses the impact of development of practical hydrogen energy technology on the economy, society and environment in Japan, and proposes some effective countermeasures, the required technical development target and a promising promotion system. The example of technology assessment assuming practical technology several tens years after is hardly found. Hydrogen energy technology is in the first stage among (1) initial planning stage, (2) technical research and development stage, (3) practical technology stage and (4) service operation stage. In the first fiscal year, as the first stage of determination of the communication route between society and technology, study was made on the concrete system image of practical technology. In this fiscal year, study was made entirely on preparation of the scenario for imaging the future economy and society concretely, modifying the planning of the hydrogen energy system. Through comparison of the scenario and system, the meaning and problem of the hydrogen energy technology were clarified. (NEDO)

  9. R and D on new energy technologies. Outlines of fiscal 1976 research results; Shin energy gijutsu kenkyu kaihatsu 1976 nendo kenkyu seika no gaiyo. Kenkyu kaihatsuhi kamihanki

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-07-01

    This report outlines the results of (1) 8 researches on solar energy technology, (2) 4 researches on hydrogen energy, and (3) 4 general researches. (1) includes the prototype measuring instrument of near IR solar direct radiation using an interference filter to measure solar spectral irradiance, the prototype small-scale solar heat power model system, selective absorption and transmission films as solar heat power generation materials, InP solar cell and new solar cell system configuration, micro-wave power transmission of solar energy, and the expansion turbine using low-boiling point coolant for space power generation. (2) includes the hydrogen energy system, high-temperature thermolysis of water at 1,000 degrees C, prototype zirconia single-crystals for new solid electrolyte fuel cells, and the large-capacity high- temperature solid electrolyte fuel cell power system. (3) includes the total new energy system, the prototype superconducting magnet for energy storage, study on mechanism of an anomalous absorption effect by irradiation of strong laser beam onto high-temperature high-density ionized gas, and low-temperature difference power generation in the ocean. (NEDO)

  10. FY 2000 report on the survey of energy conservation technology in Japan; 2000 nendo chosa hokoku. Nihon kokunai no sho energy gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of supporting self-help efforts to deal with energy environmental problems in developing countries in the Asian region, etc. and making the transfer of the energy conservation technology and petroleum substituting energy technology that are at a practical stage and are owned by Japan, evaluation of each technology was conducted in terms mainly of applicability for a model project. The existing survey data were supplemented/deleted. As the model project supposing the application to developing countries in Asia, types of industry for survey were selected as follows: iron/steel, nonferrous metal, chemical industry, oil refining, ceramics/earthware, paper/pulp, foodstuffs, textile/spinning, electricity (power generation)/gas, technologies common to all industry types. Technologies for survey were energy saving production facilities and energy saving equipment at plant with a regular scale to which the applicability as the model project was supposed. The energy saving effect was all calculated in TOE, and the method to calculate the effect was also described. The paper further described possibilities of introduction/spread of the said technologies to developing countries in Asia, introduction limitation/preconditions, cost vs. effect, etc. (NEDO)

  11. Survey for making a data book related to the development of new energy technology. Cogeneration; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Cogeneration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This is a report of 'A data book on cogeneration' surveyed by Japan Cogeneration Center under consignment from NEDO. Together with the advance of technology development, policies of new energy technology are being developed toward the introductory promotion in terms of preparation of subsidy system, field test project, advisory project for support of new energy introduction, etc. To promote the project for introducing/promoting new energy more effectively, it is necessary to arrange various data on new energy comprehensively/systematically and to prepare it as the basic data. Out of the technical fields of new energy, this report deals with the cogeneration field and collected/arranged the most up-to-date published data in terms mainly of a list of system, actual samples of introduction, subsidy system, situation of tackling it in each country, etc. The main items of data included in this report are shown below: (1) trend of cogeneration; (2) outline of system; (3) samples of introduction in Japan and abroad; (4) forecast of introduction; (5) policies on cogeneration in Japan; (6) basic technical terms. (NEDO)

  12. Achievement report for fiscal 1976 on Sunshine Program. Technology assessment of hydrogen energy technologies III; 1976 nendo suiso energy gijutsu no technology assessment. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-31

    This report contains the ultimate results of the 3-year research endeavor on 'Technology assessment of hydrogen energy technologies.' The scientists engaged in the project express their impressions at the conclusion of the research, stating: 'In the development of hydrogen energy technologies, what is the most important at the present stage is to define the formation of the energy more clearly - in what shape or at what place - so that various activities in this connection will be organized.' They say also: 'Although the type of research effort of looking into technological possibilities is quite important naturally, yet such should been carried out with a sense of purpose which is definite and concrete.' Before what are stated above may be complied with, of course, systems for development have to be arranged allowing the scientists to act in the above-suggested way. This report consists of a general discussion part and an itemized discussion part. The former summarizes the intention, aim, premise, contents, findings, opinions, etc., concerning the research work; and the latter carries a gist of the 'Hydrogen energy system concept (draft)' which constitutes the foundation on which the above-mentioned details are discussed in the former. (NEDO)

  13. Fiscal 1997 report on the development of new hydrogen atomic energy demonstrative technology; 1997 nendo kenkyu hokokusho (shinsuiso energy jissho gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    In this validation study, phenomena of excess heat which are said to be generated by electrolysis of deuterium using palladium metal, etc. as electrode are taken as `new hydrogen atomic energy,` and to clarify a possibility of using them as a future energy source, the abnormal heating phenomenon was validated and the mechanism was elucidated. The study targeted quantitative control of heat emissions. The study was finished in 1997, the fifth year from the start. The excess heat measurement could partially be reproduced; however, when conducting a confirmation experiment on the excess heat by another more reliable method under the same condition, it was found that the value of excess heat was not an absolute value exceeding measuring sensitivity and errors of the system. If the excess heat of 0.1W order is to be emitted in nuclear reaction, any reactive product should be detected in a substantial quantity. However, the product of a large quantity was not found. A possibility was found out of an increase in nuclear reaction ratio inside solid by low energy deuterium irradiation. From the above, it was concluded that the use of new hydrogen atomic energy was negative. 20 refs., 149 figs., 29 tabs.

  14. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Machine industry technology field (Machine tool); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijjtsu senryaku) kikai sangyo gijutsu bun'ya (kosaku kikai bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a machine tool field. Corresponding to construction of an environment-friendly recycling economic society and economic growth as estimated change in social and industrial structure during 2010-2025, major themes are reuse of machine tools, energy saving, environment design, chip treatment and resource recovery. With preparation of information infrastructures in an advanced information society, major issues are 3D-CAD, remote diagnosis, remote control and self-restoration. Because of decline of the birth rate, positive employment of aged persons and women is desirable. New machining technology for new materials, and fusion of various machining technologies are important. For micro-technology, study should be made on the concept and effect of micro-factory (energy saving, space saving, cost reduction, higher accuracy and higher speed). For higher-accuracy machine tool, static, dynamic, thermal and movement characteristics are the key for improving the proper technology. For faster machining. fine basic structural element, faster main spindle and faster feed are important. (NEDO)

  15. FY 1999 report on the results of the R and D of high efficiency clean energy vehicles; 2000 nendo choteisonshitsu denryoku soshi gijutsu kaihatsu seika hokokusho. Kiban gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Using the petroleum substituting clean energy, the R and D were conducted with the aim of developing vehicles which reduce the consumption of travel energy to 1/2 and the CO2 emission to 1/2 or below of those of existing vehicles. The FY 1999 results were summed up. As to the R and D of the hybrid power system, carried out were the prediction of fuel consumption performance by numerical simulation, evaluation of performance of new hybrid electric vehicles, etc. Concerning the R and D of high efficiency clean energy vehicles, the R and D of the following were reported from each of the makers: hybrid passenger car loaded with methanol fuel cells, hybrid passenger car loaded with ANG engine, hybrid truck loaded with CNG ceramic engine, hybrid truck loaded with CNG engine, hybrid bus loaded with LNG engine, and hybrid bus loaded with DME engine. Further, in the survey of synthetic fuels, the paper reported on the results of the evaluation of synthetic light oil engines and evaluation of characteristics of synthetic light oil. (NEDO)

  16. Fiscal 2000 collection of manuscripts for technology development committee on hydrogen energy and the like; 2000 nendo suiso energy nado kanren gijutsu kaihatsu iinkai yokoshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-07

    The subjects listed in the collection are (1) the research and development of international clean energy system technology utilizing hydrogen (WE-NET - World Energy Network), including the outline of the project as a whole; research on system evaluation; research and development of safety measures; development of technologies for liquid hydrogen transportation and storage; research on low-temperature materials; development of hydrogen supply station and hydrogen-driven automobile system; development of supply station for hydrogen produced by electrolysis of water; development of hydrogen fuel system; development of hydrogen production technology; development of hydrogen absorbing alloys for dispersed hydrogen transportation and storage; development of polymer electrolyte fuel cell fed with pure hydrogen; and the development of power generation technology, (2) the development of closed type high-efficiency turbine technology capable of carbon dioxide recovery, and (3) the development of frontier technology of carburation using sensible heat in coke oven gas. (NEDO)

  17. Fiscal 1999 technical survey report. Survey of energy conservation technologies in Japan; 1999 nendo kokunai no sho energy gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    NEDO (New Energy and Industrial Technology Development Organization), in its effort to implement a joint project with importing countries, endeavors to popularize energy conservation technologies by introducing them into plants in the importing countries and by demonstrating their validity on real systems. Energy conservation technologies in use in Japan's steelmaking, cement making, chemical, and oil refining industries were reassessed in view of their usefulness in the above-said project. During the reassessment, they were analyzed also for cost effectiveness for the scales on which they would possibly be introduced. Ninety-four technologies were reassessed, which involved the top pressure recovery facilities, continuous casting facilities, high frequency melting furnace, and high efficiency sintering furnace ignition device, these for the steelmaking industry; the materials crushing vertical roller mill, NSP (new suspension preheater) type cement calcination kiln, finishing process preliminary crusher, urban wastes conversion into materials for cement making or into fuel, these for the cement making industry; the multi-effect evaporator for an ammonia manufacturing process and the device for collecting waste heat at the outlet of a synthetic gas compressor, these for the chemical industry; and reduction in the amount of injection steam by use of vacuum distillation tower top steam recycling, etc., these in relation with oil refining facilities. (NEDO)

  18. FY 2000 report on the survey on the long-term energy technology strategy, etc. - Basement technology for implementation of industrial technology strategy. Survey on the extraction of preferential important technical subjects in FY 2002; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho - sangyo gijutsu senryaku sakutei kiban chosa. 2002 nendo yusenteki juyo gijutsu kadai no chushutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This survey is to investigate the consciousness of researchers and engineers of enterprises, universities, etc, of the importance of about 100 important technical subjects in 'the industrial technology strategy' prepared by the Ministry of Economy, Trade and Industry. In the questionnaire survey, the following were selected: 1)systematization of policy in consideration of the social needs and R and D of the technology to realize it; 2) R and D of the technology to advance the future frontier; 3) technical subjects that the government should promptly start to tackle in each classification in arrangement of the intellectual basis. Answers to the following items were obtained: 'selection reasons' for why it was considered important in each technical subject, 'lead time' toward the time of the industrialization, 'international positioning' of Japan against Western countries, 'possibility of heightening/maintaining the international competitive force,' and 'items that the government should participate in.' In 1), the following four big targets were arranged: 'security/safety,' 'informatization,' 'environment' and 'energy'. In 2), the following technical subjects were arranged: 'biotechnology,' 'information communication technology,' 'production technology,' 'materials/process technology,' 'energy/environment' and 'new blending/traversable/integrated technology.' In the results of the survey, analyzed were big targets, and trends and characteristics at technical field levels. (NEDO)

  19. WE-NET substask 3. Conceptual design of total system (Safety measures and evaluation techniques); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET). 3. Zentai system gainen sekkei anzen taisaku hyoka gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Under the hydrogen-utilizing international clean energy system technology project WE-NET (World Energy NET Work) in fiscal 1998, researches and studies were conducted to clearly define safety designs and to improve on accident-and-safety analyses. In relation with system safety design, investigations continued into Japanese and foreign manuals and regulations about the handling of hydrogen and its peripherals, and safe design guidelines (draft) were compiled. Anomalies and accidents supposed to be typical of each of the systems concerned were investigated. As for accident-and-safety analyses, incorporation of a turbulence model was studied in relation to models representing the leak, evaporation, and diffusion of liquid hydrogen, and improvement was achieved when the scope of evaluation was enlarged concerning the hydrogen detonation model. The integration of the two models was discussed for the due evaluation of a series of processes of liquid hydrogen leak, evaporation, diffusion, and detonation. Calculation was performed for two assumed accidents, and the results were found to justify the integration of the two models. (NEDO)

  20. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field (formed raw material field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sokeizai bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The paper described the results of the survey of the formed raw material field in relation to the FY 1999 long-term energy technology strategy. In the advancing international specialization, efforts are being made for the secure basic base technology force and cost reduction required for competition, and at the same time the aim is not to retain/improve all the formed raw material technologies, but to discriminate the materials in the aspects except the cost. By promoting the reformation into the proposed type industry, it is necessary to work out the bold strategy including the review of the system/structure for promoting the strategic technology innovation by aiming at the important formed raw material technology which can be a life line for the assembly industry, in particular. Concretely, the comprehensive technology system which concentrated a variety of engineering knowledge/information was constructed. The system is shifted to the one that adopted information/communication technology. The conversion in the early time to the proposed type industry is attempted. Japan acquires capability for heightening the level of technology, by which Japan will continue leading the formed raw material technology to the world's top level. Japan realizes the network consisting of the industry, university and government. The environment is realized where new personnel will naturally enter the formed raw material industry and bottom up the total technology force. (NEDO)

  1. Research report of fiscal 1997. Basic research on the commercialization of innovative energy technologies; 1997 nendo chosa hokokusho. Kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper summarizes the research result in fiscal 1997 from the basic research results on the commercialization of innovative energy technologies. The target of a photovoltaic power generation market includes isolated power sources (several kWp) for distant places or developing countries, and those (several tens kWp) for personal residences or public facilities. Although the former is mainly promoted in the West, while the latter over the world, their profitability is unsolved. Power plants over several hundreds kWp are in demonstration test. Solar heat power generation of several tens to hundreds MWp is most profitable, however, small-scale one is poor in feasibility. Australia takes an interest in distributed photovoltaic power generation directly connected with actual lives of residents, and has a dominant opinion that desert is useless as large-scale site. This country lays emphasis on protection and maintenance rather than positive use of desert based on a basic cognition that desert is easily changed and broken. The Australian government announced power company`s obligation to use renewable energy by 2%, and a strong organization is scheduled to be newly established. 59 figs., 57 tabs.

  2. Report on the development/comprehensive research of new hydrogen energy demonstrative technology; Shinsuiso energy jissho gijutsu kaihatsu sogo kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-06-01

    In this project, the excess heat phenomenon caused by electrolyzing heavy water using palladium metal, etc. as electrode was captured as `new hydrogen energy.` To make a possibility of being as a future energy source clear, the abnormal heating phenomenon was verified. By elucidating the mechanism, the paper aimed at quantitatively controlling the heat generation. The R and D period was four years from fiscal 1993, and the details of the research are about the excess heat measuring test, material analysis/development tests, test on detection of reaction products, information collection/arrangement, international research cooperation. As a result of the research, a part of the excess heat measurement was surely able to be reproduced. However, when a confirmation experiment on the excess heat was conducted by another more positive method under the same conditions, it was found that the excess heat quantity was not the absolute excess heat quantity exceeding the measuring sensitivity/errors of the system. Supposing the excess heat of 0.1W order is generated in nuclear reaction, any of reaction products should be detected in a considerable quantity. However, no reaction products were not detected. 42 refs., 241 figs., 55 tabs.

  3. Fiscal 1998 research report. Application technology of next-generation high-density energy beams; 1998 nendo chosa hokokusho. Jisedai komitsudo energy beam riyo gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Survey was made on application technologies of next- generation high-density energy beams. For real application of laser power, application to not exciting source of YAG crystal but machining directly is highly efficient. For generation of semiconductor laser high-power coherent beam, phase synchronization and summing are large technological walls. Short pulse, high intensity and high repeatability are also important. Since ultra-short pulse laser ends before heat transfer to the periphery, it is suitable for precise machining, in particular, ultra-fine machining. To use beam sources as tool for production process, development of transmission, focusing and control technologies, and optical fiber and device is indispensable. Applicable fields are as follows: machining (more than pico seconds), surface modification (modification and functionalization of tribo- materials and biocompatible materials), complex machining, fabrication of quantum functional structured materials (thin film, ultra-fine particle), agriculture, ultra-precise measurement, non-destructive measurement, and coherent chemistry in chemical and environment fields. (NEDO)

  4. Investigation on the chemically fixing technique of carbon dioxide utilizing solar energy; Taiyo energy riyo ni yoru nisanka tanso no kagakuteki koteika gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    1993-03-01

    This report describes the results of effective fixing technique of CO2 by utilizing solar energy. First of all, the investigation was directed to the technique for synthesizing ethylene, hydrocarbons and alcohol by electrochemical reduction of CO2. The power required for this process is supplied by photovoltaic power generation. Development of excellent electrode catalyst is needed because the reduction of CO2 requires a high overvoltage. It is desirable to enhance the selectivity of the reaction for specific material and improve the transport process in the electrolytic cell. Next, designing of material and reaction of photocatalysts using semiconductor electrode and semiconductor particulate was examined. A semiconductor electrode made of FeS2 is inexpensive and has a high ability of collecting solar light. In the category of photocatalysis system, a photocatalytic system in which semiconductor particles are embedded in vesicle and a photpocatalyst based on potassium niobate are noteworthy. As biosystem, the method of reducing CO2 by calcareous algae which simultaneously advances fixing and calcification of CO2 by photosynthesis is noteworthy. 129 refs., 45 figs., 20 tabs.

  5. Survey on construction of the database for new energy technology development. Fuel cell; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the data related to technological development of new energy, the database for fuel cells was prepared. The major international conferences held in fiscal 1996 were reviewed. As the atmosphere of the whole conference, phosphoric acid fuel cell (PAFC) is in a stage just before practical use, and molten carbonate fuel cell (MCFC) is in a stage of the demonstration study of MW class one. The study on solid oxide fuel cell (SOFC) and polymer electrolyte fuel cell (PEFC) is in considerable progress. In particular, the application of PEFC to automobiles is in real investigation. For the database, kinds and features of various fuel cells, operation principles, system configurations of FC plants, application fields, and characteristics were arranged. Field test examples for public and industrial uses were separately arranged, and in particular, the application examples of PAFC were presented together with developmental conditions of the other fuel cells. Overseas situations were equal to domestic ones, and their marketability was predicted. The Japanese subsidy policy and some U.S. policies were also arranged. 28 refs., 51 figs., 37 tabs.

  6. Data book on new energy technology development in FY 1997. Photovoltaic (PV) power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Taiyoko hatsuden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of understanding the present status of photovoltaic power system (PVPS) and supporting its promotion, various data were collected. The significance of adopting PV power technology was specified for customers of various levels, such as nation, local communities, industries and individual households, to clarify the CO2 reduction effect and energy pay-back time. Data illustrate the solar cell production according to region, cell types, industries, applications, production value, and market price. Policies for PVPS in industrial countries were compared with those in Japan. Distribution of PVPS in various countries was compared with that in Japan in respect to installations and purposes of the introduction of PVPS. Financial aid programs such as subsidies, tax benefits and loans for the installation of PVPS in Japan were listed. The trend of PV-related budget of MITI was shown with every project`s description. Steps of introducing PVPS from plan to installation were depicted in the form of flow chart. Were shown measures sponsored by the government or local organizations to promote PVPS. Domestic and foreign firms related to PVPS including PV module suppliers, and PV installation contractors were listed

  7. Report on the FY 1999 survey on long-term energy technology strategy/basic survey for working out industrial technology strategy. Technology strategy by field - chemical/process field (chemical/process technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (kagaku process bun'ya (kagaku process gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As to long-term energy technology strategy, the paper described the results of the FY 1999 survey of chemical/process technology. The future chemical technology should be transformed from the material production technology in which priority used to be given to convenience to new chemical technology in which the functions needed are to be created. The shortage of the developmental period and minimization of the waste are also desired by the use of new methods. For it, the industry/government/university should gather wisdom together and fulfil the requests from other industries of the country under the circumstances of the society which is aging, is decreasing in birthrate, and is being highly information-oriented. At the same time, the technology should be contributional to constructing the circulating type society which has environmental harmony. If not, it cannot be the technology which is recognized by the society. Efforts should be made for the fundamental technology development, technology to create the materials needed in the society, and development of new process technology to be recognized in the society. Further, the development of technology to meet the needs/restraints from the society should be promoted as seen in the environmental hormone. At the same time, the intellectual base should be prepared such as arrangement of the technology database for advancing smooth technology development. (NEDO)

  8. FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 2. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The paper conducted the development of the environmentally friendly type high efficiency energy utilization system and the R and D of the high efficiency energy effective utilization technology, and the FY 2000 results were summed up. As to the energy transportation/storage technology, the R and D were made on the following: methanol/energy system, non-equilibrium high efficiency methanol decomposition reaction technology, development of multiple functions of catalyst, high efficiency heat pump technology using hydrogen storage alloys, heat-hydrogen recovery/transportation/utilization technology, vacuum insulated heat transport piping system, surfactant used for high density heat transport, high density latent heat transportation technology, etc. Concerning the energy supply/utilization technology, the R and D were made of the heat supply system using high efficient heat pump corresponding to multiple fuels. Relating to the environmental load reduction technology, the energy conserved heat pump system using natural coolant. As to the optimum system design technology, the comprehensive preparation of element technology, etc. (NEDO)

  9. Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 3. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes achievements during fiscal 1998 on researching part of the energy transportation and storage technologies, energy supply and utilization technologies, environmental load reducing technologies, and optimal system design in the 'research on highly efficient and effective energy utilization technology'. With regard to energy transportation and storage technologies, researches and developments were performed on a vacuum adiabatic transportation piping system, surfactants used for high-density heat transportation and high-density latent heat transportation technologies. In the field of energy supply and utilization technologies, researches and developments were carried out on a heat supply system using high-performance heat pumps capable of using multiple kinds of fuels, and a compression and absorption type hybrid heat utilization system. For the environmental load reducing technologies, research and development were performed on a power saving heat pump system utilizing natural coolant. In researching the optimal system design technologies, overall adjustment was made on the element technologies, whereas technological discussions and site surveys were executed by the committees at the same time. The latest achievements accomplished to date was published in a book. (NEDO)

  10. Fiscal 1997 report on the model project for the effective energy consumption in developing countries. Survey of changes of energy conservation technology and environmental protection technology in the oil refining industry in Japan; 1997 nendo chosa hokokusho. Hatten tojokoku energy shohi koritsuka model jigyo (Nippon sekiyu seiseigyo ni okeru sho energy gijutsu to kankyo taisaku gijutsu no hensen chosa hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For global scale measures to be taken for environmental protection, it becomes more and more important in the future to positively transfer and spread energy conservation technologies of Japan to overseas countries. Especially, it is effective for both economic growth in the Asian region and global environmental protection to transfer technologies which the oil refining industry has been developing and accumulating. Energy conservation in the oil refining industry means the energy conservation by strengthening the operational control at the first and second oil crises in the first stage, the energy conservation in the second stage which was accompanied by small and medium scale plant/equipment investments during several years after the first stage, and the energy conservation in the third stage which was accompanied by large scale investments from the first half of the 1980s to the present, resulting in improvement of 40% over before the first oil crisis. As to environmental protection measures, measures to reduce waste from oil refinery against air pollution and water pollution were prepared by the first half of the 1970s, and technologies were established of waste water treatment, flue gas desulfurization and denitrification. A lot of facilities for improvement of product quality and for low pollution were installed. In addition to environmental technologies, also in other industries, there were seen the heightening of thermal efficiency of kiln and thermal efficiency of cooling technique of clinker cooler in the cement industry and the improvement of productivity in the paper/pulp industry. 360 figs., 62 tabs.

  11. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (development of high-efficiency production process technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (kokoritsu seisan process gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Development is made of high energy-efficiency laser processing technology and high efficiency/high grade photon generation/control technology as laser light source, for the purpose of energy conservation/efficiency heightening of production processes which require a large amount of energy such as welding, joining, surface treatment, and particle fabrication. As to keyhole dynamics of the molten metal generated on the laser weld, construction of simulational mathematical models was started. Equipment to fabricate semiconductor ultrafine particles which become the core of quantum dot functional structures was designed to fabricate particles. In-situ optical measuring technology was studied of element/size of particles of below 30 nm in size by emission spectroscopy associated with the plasma irradiation. As tightly focusing all-solid-state laser technology, studied was the wavelength conversion method in which harmonics are generated four times as much as the fundamental wave due to high efficient generation of high power UV laser. Also studied were high laser strength, low optical losses, conditions for fostering high homogenity crystals. Technology for high accuracy processing of element surface was established. High efficiency photon generation technology was comprehensively investigated. 140 refs., 276 figs., 46 tabs.

  12. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 3); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 3. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy (continued), energy supply and utilization, reducing environmental loads, and designing the optimum systems). The R and D on heat transfer system through the vacuum heat insulation pipes involves fabrication, on a trial basis, the vacuum insulation covers for the vacuum insulation tubes, joints, flanges and valves for the 80A pipes, and the heat loss evaluation test for each item. The R and D on the energy supply and utilization techniques involves the heat transfer systems for a variety of fuels by the highly functional heat pump, and compression/absorption hybrid type heat-utilization system. The hybrid type heat-utilization system simulation results suggest possibility of achieving exergy efficiency of 56% as the development target by use of the new medium. The R and D on the environmental load reduction involves the power-saving type heat pump systems which use a natural coolant. (NEDO)

  13. FY 2000 report on the results of the development of the environmentally friendly type high efficiency energy utilization system. Part 1. Study of the effective utilization technology of high efficiency energy (Study of the optimum system design technology); 2000 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    The paper conducted the development of element technology and comprehensive adjustment which are related to the development of the environmentally friendly type high efficiency energy utilization system and the study of the high efficiency energy utilization technology, and the results of FY 2000, the final fiscal year, were summed up. As to the R and D of the exhaust heat reforming/recovery system, the internal heat exchange type distillation tower was developed which has a good energy conservation effect and enables the heat supply outside. Concerning the R and D of the cogeneration system using low calorie exhaust gas, the following were conducted for further improvement of the performance of electrothermic elements: evaluation of the thermoelectric performance using bulk elements, development of new elements and evaluation of the energy balance at the time of combustion, etc. Relating to the R and D of the low temperature exhaust heat utilization cogeneration system, conducted were the development of thermoelectric materials and the fabrication/evaluation study of module. Moreover, WATT20A equipped with the original power generation module developed in this study was fabricated, and the data on the operation at the temperature of 150 degrees C were obtained by WATT-20HT. (NEDO)

  14. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 2. Research study on promotion of international cooperation (standardization of hydrogen energy technology); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 2. Kokusai kyoryoku suishin no tame no chosa kento (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes the basic study on standardization of hydrogen energy technology, and the research study on ISO/TC197 in fiscal 1996. As a part of the WE-NET project, the subtask 2 aims at preparation of standards necessary for practical use and promotion. Developmental states in every field of hydrogen energy technologies, current states of domestic/overseas related standards and laws, and needs and issues of standardization were surveyed. In particular, the needs and issues were clarified in relation to existing standards and laws from the viewpoint of specific hydrogen property. ISO/TC197 was established in 1989 for standardization of the systems and equipment for production, storage, transport, measurement and utilization of hydrogen energy. Four working groups are in action for the supply system and tank of liquid hydrogen fuel for automobiles, the container and ship for complex transport of liquid hydrogen, the specifications of hydrogen products for energy, and the hydrogen supply facility for airports. The draft international standards were proposed to the international conference in 1996. 16 refs., 21 figs., 41 tabs.

  15. Fiscal 1997 report under consignment from NEDO on photon measuring/processing technology (development of power generation facility use high-function maintenance technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A research/development was conducted on technologies of photon applied measuring/photon applied processing/photon generation which are usable for heightening of reliability and maintenance efficiency of power generation facilities. In fiscal 1997, high melting-point metal particles were manufactured by high energy density laser for formation of high temperature and stabilized fine functional circuit. Further, a wavelength changeable ultra red laser light source was studied which can make in-situ measurement of gas concentration and components. A study was also made to examine the surface composition by measuring fluorescent X-rays emitted by radiating high intensity laser beam on the surface of material. A rod type and a slab type as a high-output complete-solidified laser are under development. There is also a development aiming at high speed/high quality photon processing such as high speed/high precision welding/cutting and laser joining. Besides, a study is being made of high energy pulse/high quality beam complete-solidified laser. The paper made a comprehensive survey of the trend of the photon measuring/monitoring technology, and made a systematical arrangement of the developmental subjects extracted. 142 refs., 357 figs., 62 tabs.

  16. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 2); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the (techniques for transportation and storage of energy). The R and D on methanol energy systems involves the R and D on decomposition and synthesis catalyst of methanol and methyl formate for the waste heat sources of relatively low temperature. The R and D on high-efficiency techniques using hydrogen-occluding alloys involves development of heat exchangers of low sensible heat ratio, fabrication of double-effect type MH heat pump cycle devices, and demonstration tests for the system operation. It is found that the heat output of the hydrogen-occluding alloy for high temperature use is 0.18kW/kg at 90 degrees C, and that the alloy can be massively produced. A thermal utilization efficiency COP of 0.68 is obtained for the double-effect type MH heat pump cycles. The R and D on the heat-hydrogen recovery, transportation and utilization techniques involves designs and fabrication on a trial basis of a sensible heat recovery unit. (NEDO)

  17. Model project for enhancing energy consumption efficiency in developing countries. Report on changes of energy conservation technology and environmental protection technology in the chemical industry of Japan; Hatten tojokoku energy shohi koritsuka model jigyo. Nippon kagaku kogyo ni okeru sho energy gijutsu to kankyo taisaku gijutsu no hensen hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the economic growth and the global environmental protection in the Asian area, an investigation was carried out into energy conservation technology and environmental protection technology in the chemical industry of Japan. Measures for energy conservation are shifting from those which do not cost so much such as reduction in excess air rate of the heating furnace, and reduction in reflux ratio of the distillation tower to those with equipment investment such as waste heat recovery of the heating furnace and waste heat recovery of the distillation tower. In the 1980s, the utilization of low temperature waste heat by absorption type refrigerator and heat pump was promoted and the energy utilization efficiency by computer control was enhanced. Concerning environmental measures, the following were carried out: installation of the flue gas desulfurization device and reconstruction of high-rise stack, reduction of NOx by combustion control, smoke/dust disposal of electrostatic precipitator, combustion of hydrocarbon causing photochemical oxidant, catalytic oxidation, condensation, treatment by activated carbon, activated sludge treatment for BOD/COD, diaphragm process for dimethylmercury, ion exchange resin process, etc. 21 refs., 29 figs., 27 tabs.

  18. Development for environmentally friendly and highly efficient energy utilization system in fiscal 1998. Pt. 1. Research on highly efficient and effective energy utilization technology (Research on design technology for optimal system); 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 1. Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper summarizes achievements of the researches during fiscal 1998 on researching a highly efficient and effective energy utilization technology. With regard to technologies to recover and convert unutilized energies, a process simulator was developed, basic internal structure was discussed by experiments and simulation, and substance migrating and heat exchanging characteristics were identified by using partial testing devices. These researches and developments were performed for the waste heat reforming and recovering systems used in chemical plants. In developing a thermoelectric generation system using low calorie exhaust gases, thermoelectric power generating materials were developed, a powder manufacturing technology was developed, a thermoelectric conversion element bulking technology was developed, a thermoelectric power generation system using porous structures was simulated, development and concept design were carried out on system element technologies. In the research and development of the thermoelectric generation system using low calorie exhaust gases, advanced materials and modules were manufactured, the modules were evaluated, and power generation systems were researched. In addition, researches were performed on energy transportation, supply and utilization technologies, and on environmental load reducing technologies. (NEDO)

  19. NEDO Forum 2001. Session on development of energy and environmental technologies (For promotion of comprehensive development of hydrocarbon-based energy); NEDO Forum 2001. Energy kankyo gijutsu kaihatsu session (tanka suisokei energy no sogo kaihatsu suishin no tame ni)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Pointed out in a lecture entitled 'How technology development for hydrocarbon-based energy resources should be' was the need of technologies for clean energy production; CO2 emission reduction; NOx, SOx, soot, and dust reduction; and the expansion of exploitation of resources now left unused. Reported in a lecture entitled 'Cooperation with China on coal liquefaction' were the result of a coal liquefaction demonstration plant feasibility study conducted for coal from Inner Mongolia, and so forth. Reported in a lecture entitled 'Development of coal oil upgrading technology' were the result of the operation of a test plant, and so forth. Reported in a lecture entitled 'Research and development of HyperCoal' were the result of HyperCoal manufacturing technology research and development, designing of a HyperCoal-fired gas turbine power generation system, and so forth. In addition, development of technology for high efficiency conversion of biomass energy and development of technology for refuse gasification/melting power generation were reported. (NEDO)

  20. Achievement report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. 2. Research of technology of effectively utilizing high-efficiency energy / research of optimum system designing technology; 1998 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu. 2. Kokoritsu energy yuko riyo gijutsu no kenkyu, saiteki system sekkei gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This 2nd volume deals with the transportation and storage of energy in the above-named research. In search of technologies for transporting exhausted heat from the industrial area to the urban section for consumers to utilize the heat for driving their air-conditioners and hot water supply systems, the decomposition and composition reactions of methanol are utilized for a long-range transportation system. The subjects taken up in this connection include the research and development of a methanol energy system, non-equilibrium high-efficiency methanol decomposition technology, multifunctional catalysts, and highly active/selective catalysts capable of promoting reversible endoergic/exoergic reactions. Research and development is also conducted of a high-efficiency heat pump technology using hydrogen-absorbing alloys, and such a pump will realize an air-conditioning system not dependent on chlorofluorocarbon. In the research and development of a long-range heat transportation system using hydrogen-absorbing alloys, a study is made of technologies of heat/hydrogen recovery, transportation, and utilization. (NEDO)

  1. FY 1999 Technical research and development for environmentally friendly and highly efficient energy utilization system. Technical research and development for highly efficient and effective energy utilization (Technical research and development for optimum system designs - Part 1); 1999 nendo kankyo chowagata kokoritsu energy riyo system kaihatsu seika hokokusho. 1 Kokoritsu energy yuko riyo gijutsu no kenkyu (saiteki system sekkei gijutsu no kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    Research and development program is conducted for the elementary techniques as part of the eco-energy urban project of New Sunshine Project. Described herein are the FY 1999 results for the 'techniques for recovery and conversion of unutilized energy'. The R and D on waste heat recovery and conversion for chemical plants designs an internal structure of the 'wetted wall column for shell side as the stripping section' for increasing quantity of heat exchanged inside, and stably operates the bench plant for 100 hours or more. The R and D on thermoelectric power generating systems using low calorie exhaust gases involves development of materials, production of fine particle materials and sinters, and evaluation of their functions, among others. The program for application of the techniques to commercial plants confirms applicability of a 3kg thermoelectric power generating system to automobile coating process. The R and D on systems for thermoelectric recovery of low-temperature waste heat finds cracks on the ceramic plate for the power generating system WATT100, disassembled for repair. (NEDO)

  2. Survey report of FY 1997 on the long-term energy technology strategy. Survey on the pre-assessment system of energy and environmental technology research and development; 1997 nendo chosa hokokusho (choki energy gijutsu senryaku chosa). Energy kankyo gijutsu kenkyu kaihatsu no jizen hyoka ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    To select projects of the New Sunshine Program which is the locomotive for Japan`s research and development of energy and environmental technologies and to map out the Program`s long-term strategy, it is required to develop an effective methodology of assessing research and development themes. It is also necessary to establish the pre-assessment system which makes the assessment process more logical and which will enable the priority setting among different themes on the basis of objective and quantitative analysis. Additionally, transparency should be ensured for such a pre-assessment process through disclosure to the public and other means. The present survey aims to concretize the pre-assessment system by studying the system and techniques of an assessment system which is applicable to the research and development themes of the New Sunshine Program and is objective, quantitative and logical and which can ensure transparency and by receiving suggestions on the pre-assessment of Japan`s research and development of energies and environmental technologies through research on overseas trends of government-led research and development. 3 refs., 7 figs., 26 tabs.

  3. Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Survey of research management technique to contribute to formulation of long-term energy strategy); 2000 nendo choki energy gijutsu senryaku ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (choki energy senryaku sakutei nado ni kansuru kenkyu kanri shuho no chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of acquiring research management related basic materials necessary in the study of long-term energy strategy, a survey is conducted of the history, theory, and techniques of research management, the state of its utilization, and the products. The results of the survey are compiled into an introduction, itemized discussion, and materials. In the introduction, the purpose and basics of research management are discussed and confirmed. Taken up in the itemized discussion are an item (1) on research management relating to the selection of themes for research and development, which discusses the formulation of research and development strategy, selection of themes for research and development, formulation of plans for them, and a theme selection assisting system, an item (2) on research management relating to the management of research implementation, which discusses the management of implementation of research and development, interim assessment, and an implementation management assisting system, and an item (3) on the studies of key points for implementation and of research management for NEDO (New Energy and Industrial Technology Development Organization) to practice. As for the materials, they comprise commentaries on theories and techniques, an ex post facto assessment system and instances of assessment, list of persons related to research management, and commentaries on reference materials. (NEDO)

  4. Achievement report for fiscal 1983 on Sunshine Program-entrusted survey and research. Cooperative project between Japan and Australia, etc., on solar energy technology (Cooperation between Japan and France on solar energy technology); 1983 nendo Nichigonado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichifutsu taiyo energy gijutsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1984-03-01

    This paper reports a survey on solar heat utilization technologies conducted in fiscal 1983 in accordance with a scientific cooperation agreement signed by the Japanese Government and the French Government. The survey was carried out by two employees with the solar technology development office of the New Energy and Industrial Technology Development Organization who were dispatched to France on a tour in the period March 13-24. Concerning the 'French Photovoltaic Program 1982-1986,' knowledge on the goal of the program, long-term research and development, and budgetary matters were obtained at the AFME (French Energy Management Agency) head office and its branches. Relations of AFME with EC (European Community) projects were clarified. The photovoltaic power system (50kW) of Nice Airport is one of the EC projects, and was built thanks to financial aids by EC and AFME. The power system is now in service as a power source for electronic equipment in the airport management building and for taxi lights installed on the ground. The CGE (Compagnie General d'Electricite) central laboratory and the Rhone Poulenc Specialites Chimique were visited, when information on the research and development of a ribbon crystal pulling process and solar-grade silicon was acquired. (NEDO)

  5. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

  6. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) - survey/study concerning international cooperation (Survey/study concerning standardization of hydrogen energy technology); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of R and D of hydrogen energy technologies and the promotion of their practical use and proliferation, conducted were research on standardization of hydrogen energy technologies and research/study on draft international standards proposed by ISO/TC197. In the research on the standardization, legislation, rules and guidelines for Japan were compiled based on reference to the materials in the 'sourcebook for hydrogen applications' which was prepared in the U.S./Canada. The Japanese laws and regulations applicable to hydrogen are the high pressure gas safety law, fire service law, industrial safety and health law, building standard law, law on prevention of disasters in petroleum industrial complexes and other petroleum facilities, road vehicles act, road traffic law, harbor regulation law, etc., with related legislation compiled under headings classified as pressure containers, gas facilities, consumption, transportation, explosion proofing of electrical equipment, list of laws, and related documents. In reference to ISO/TC197, the 8th plenary meeting and WGs were held during April 6-8, 1999, in the U.S., where the progress status report, study contents, future schedule for newly proposed items, etc., of each WG were reviewed and discussed. (NEDO)

  7. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the environment friendly type production technology. High-functional chemical synthesis bioreactor (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kankyo chowagata seisan gijutsu (kokino kagaku gosei bioreactor) kenkyu kaihatsu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of developing production technology of chemical substances which are resource conservative, energy saving and less in environmental loads, a R and D was conducted of a high-functional chemical synthesis bioreactor. The paper reported the results of fiscal 1996. As for proliferation control breeding technology, relating to the switch control technology of proliferation related genes by regulatory factors, the effectiveness on an incubator level was demonstrated, and at the same time improvement of reactor performance in using this technology was studied on paper. As to the manifestation control breeding technology, the actual design of the development of manifestation promotion technology by bent DNA, etc. was proceeded with, and at the same time the following were commenced: selection of bent DNA, confirmation of bent characteristics, and work of vector construction using candidate bent DNA. Further, the simple assessment system of manifestation vectors was constructed. In the development of bioreactor system technology, the actual design was started of the two-stage culture continuance system which separated proliferation and enzyme production. 48 refs., 41 figs., 6 tabs.

  8. Fiscal 1996 report on the results of the R and D under a consignment from NEDO of the technology to fix and effectively use carbon dioxide using bacteria and microalgae (for public); 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku (saikin sorui nado riyo nisanka tanso koteika yuko riyo gijutsu kenkyu kaihatsu seika hokokusho (kokaiyo))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the purpose of contributing to the solution to the global environmental problem, a technology is developed in which by searching for/breeding/developing bacteria, etc. which conduct photosynthesis highly effectively, CO2 is fixed and recycled. The fiscal 1996 R and D is outlined as the utilization of bacteria, microalgae, etc. Obtained were microalgae exceeding the conventional strains in CO2 fixation ability, and bacteria/microalgae excellent in production of polysaccharides, hydrocarbon, lipid, biological active substances, etc. The fundamental study was continued of CO2 integrated enzyme function/reaction system as molecular biological breeding. In the cell fusion, a set-up of conditions for green algae was started. For the confirmation of performance of high dense/quantity culture technology using solar light, further improvement of performance and systematization, 200L scale testing equipment was manufactured. It is a collective reactor and enabled study of ventilation/agitation and control of light strength. A reactor analysis model was constructed. Also including the conversion into useful substances, energy/material balance was systematically studied. Collection of technical literature and information exchanges were made in Japan and overseas. 276 refs., 475 figs., 156 tabs.

  9. Fiscal 1998 research report on International Clean Energy Network using Hydrogen Conversion (WE-NET). Subtask 2. Research on promotion of international cooperation (research on standardization of hydrogen energy technologies); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) sub task. 2. Kokusai kyoryoku suishin no tame no chosa kento (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report summarizes the fiscal 1998 research result on the basic research on standardization of hydrogen energy technologies, and ISO/TC197. As for the standardization, in relation to the hydrogen station in the WE-NET second phase research, the laws related to handling of gaseous hydrogen, and the basic issues on facility and safe handling were studied. As for ISO/TC197, the following draft standards were examined: Fuel supply system interface for liquid hydrogen vehicles, fuel tank for liquid hydrogen vehicles, container for liquid hydrogen transport, specification of hydrogen fuel, hydrogen fuel supply facility for air ports, gaseous hydrogen and hydrogen mixture fuel system for vehicles, gaseous hydrogen fuel connector for vehicles, gaseous hydrogen fuel tank for vehicles, and basic items for hydrogen system safety. Final examination of the fuel supply system interface for liquid hydrogen vehicles, and the specification of hydrogen fuel was finished, and these are scheduled to be registered for ISO. (NEDO)

  10. FY 2000 report on the results of the R and D of the immediately effective/innovative energy technology. Development of the regenerative technology of energy saving type metal dust; 2000 nendo sokkoteki kakushinteki energy gijutsu kenkyu kaihatsu seika hokokusho. Sho energy gata kinzoku dust kaisei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of the technology to recover iron and zinc components directly from high temperature exhaust gas emitted from the steel-making use electric furnace, etc. This process is more simplified than the conventional dust treatment process and markedly reduces the energy needed for zinc recovery. In FY 2000, the following were carried out: 1) development of the element technology to recover metal components in high temperature exhaust gas; 2) development of the technology to optimize the recovery process for metal components in high temperature exhaust gas. In 1), the following were proceeded with: grasp of conditions for metal recovery; development of the equipment to select/separate low vapor-pressure metal components; development of the heavy metal separation equipment to select/condensate zinc. As to the development of the equipment to select/separate low vapor-pressure metal components, it was confirmed by the element test that it was possible to separate iron by carbon material filter. Further, the reaction amount of gasification of carbon material was estimated to be small by the element test and simulational calculation. In 2), the bench-scale test device and small pilot test device were designed/fabricated. (NEDO)

  11. Fiscal 1997 R an D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (high-efficiency and analysis and manipulation technology for DNA); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (DNA nado kokoritsu kaiseki sosa gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Through the observation of super spiral DNA fixed on a spermin or spermidine treated mica substrate by AFM (atomic force microscope), fixation of DNA without any deformation in solution was clarified, and visualization of the spiral structure of DNA were successfully achieved. Manipulation of Xe atoms adsorbed on an Si(111) surface was certainly possible by using STM (scanning tunneling microscope)/atom probe equipment. A nucleation mechanism in crystal growth was studied for various organic source-molecules/GaAs(001) surface systems, and formation of high-density nuclei on the GaAs surface was achieved by accelerating the translational energy of Ga material molecules up to 6eV or more. Ziegler- Natta catalysis important for industrial polymerization of olefin molecules was precisely analyzed by first-principle dynamic simulation. A large-scale simulation of zeolite catalyst is also in promotion for methanol to gasoline conversion. 51 refs., 87 figs., 7 tabs.

  12. Fiscal 2000 survey report on technological trends. Survey on trend of high-density energy beam technology concerning conservation of energy; 2000 nendo gijutsu doko nado chosa hokokusho. Energy shiyo gorika ni kakawaru komitsudo energy beam technology no doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    There is a possibility that machining technology using high-density energy beam will bring an epoch-making change to micro-nano area processing. In particular, a laser beam having high controllability is indispensable. This is a report of the fiscal 2000 survey. The survey was conducted on laser beam generation, control and nano-diagnostic techniques, micro-nano optics technologies and machining technologies, with the development problems and targets summarized. Laser beam generation/control technologies, which become the basic tools for micro-nano manufacturing, were investigated, as were inspection technologies for the purpose of checking the functions of nano structures created. Particularly, the investigation elucidated the significance of development of a femtosecond solid state laser based on a semiconductor laser and the control techniques of their phase. Further, necessity was emphasized in developing X-ray probing, infrared and terahertz spectroscopy which are essential for nano-diagnostic techniques. In optics technologies, the paper described the importance of photonic crystals which enable less-than-wavelength machining or electrical beam control using interference effect. The possibility of fabricating photocatalysts with nano-particles was also mentioned, as was the manufacturing of nano-functional structures. (NEDO)

  13. FY 1999 New Sunshine Project survey research project - Survey on the long-term energy technology strategy, etc. Fundamental survey to decide on the industrial technology strategy - Technology strategy by field (Electronic information technology field - Human process ware technology field of the computer relation field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (denshi joho gijutsu bun'ya (computer kanren bun'ya no uchi, human process ware gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey/study were conducted to contribute to proposing technology strategies such as the analysis of the present state of technical competitive force and the forecast in the human process ware industry technology field of the computer relation field. The human process ware is a system aimed at fermenting human power for thinking, problem solution and creation. Its main subjects are the following three: close society technology for will communication by automatically learning backgrounds of people joining the community; topics community technology for community formation for the appropriate people/organizations by grasping true topics/purposes from conversation; active interaction technology for supporting creative activities of users/community and making conversation with users. Further, in the region of the technology to meet the requests/restrictions from the society, the following are expected: energy/resource conservation; realization of the life with ease/safety and of high quality in the aged society; realization of the advanced information network society which becomes the basis of a new economic society. (NEDO)

  14. Research report for fiscal 1998 on development of environmentally friendly high-efficiency energy utilization system. Research of optimum system designing technology (Research of effect of eco-energy city system technology introduction to Osaka); Kankyo chowagata kokoritsu energy riyo system kaihatsu Saiteki system sekkei gijutsu no kenkyu 1998 nendo chosa hokokusho (Osakafu). Ekoene toshi system gijutsu donyu koka no chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Concerning the district in Osaka Prefecture selected for study in fiscal 1997, it is investigated whether energy efficiency is enhanced, and environmental impact reduced, by the introduction of element technologies, and the findings are compared with the results expected to be produced without their introduction. Problems about their introduction are also discussed. Taken up for study are the collection and utilization of heat from a water granulated slag manufacturing plant of an iron mill, exhaust heat reform and recovery system at a chemical plant, heat supply system driven by a high-performance heat pump capable of dealing with various kinds of fuels, compression/suction hybrid heat utilization system, and a cold heat supply system using microspheres. Annual energy consumption, CO2 and NOx emissions, and costs are calculated for each of them. Concerning these element technologies, various tasks are discussed, related to the technology of their systematization, economy, dissemination of district heat supply, and wide-area heat supply businesses utilizing exhaust heat. As the result, it is concluded that the primary energy consumption as a whole is reduced upon their introduction and that energy saving effect and environmental impact reducing effect are in presence. (NEDO)

  15. FY 1999 research and development results. Preparatory study for the underground thermal energy storage system; 1999 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    The study is conducted for the underground thermal energy storage system which utilizes heat capacity of the underground, e.g., aquifer, to exchange heat with the underground, and the FY 1999 results are described. For establishment of the concept of the underground heat storage systems, 2 sites are selected for each of Tokyo, Osaka and Sapporo for the study as the geological ground models, for their weather characteristics. Two cases are considered for the site where underground heat exchangers are installed, open space and immediately below a building. The heat-storage system comprises a high-efficiency heat pump, water heat-storage tank and cooling tower. The evaluation results indicate that energy saving rate of 37% or more and CO2 reduction rate of 9.5% or more are achievable in all areas except Sapporo, i.e., Tokyo and Osaka. The economic evaluation results indicate that the simple pay-out period is around 100 years for Tokyo and Osaka, and 80 years for Sapporo. The underground heat storage system is approximately 10% lower in life-cycle cost than the conventional system, 3 versus 3.3 billion yen for the period of 60 years. (NEDO)

  16. Survey and research achievement report for fiscal 1980 on patent and information under Sunshine Program. Survey of information on new energy technology development (Solar energy); 1980 nendo tokkyo joho chosa kenkyu seika hokokusho. Shin energy gijutsu kaihatsu joho chosa (taiyohen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Solar energy as defined by the United States includes hydroelectric power, biomass, and the ocean. The short-term strategy deals with passive solar air-conditioning, hydroelectric power, and biomass direct combustion. The medium-term strategy involves positive heating and wind power. The long-term strategy covers heat for agriculture, photovoltaic power, and OTEC (ocean thermal energy conversion), and the ultralong-term strategy covers power generation in space and photochemical conversion. Canada is behind other countries in the conversion of solar energy into power, and solar energy is used but passively as heat source, this because this country is rich in other resources. In West Germany, solar energy may be exploited for hot-water supply and heating at high latitudes, but it is not likely that it will be used for power generation. Home heating offers some appeal since potential demand for it is great. In Britain, the use of solar energy is not a pressing matter, this because systems for effective use of coal have long been established at homes, society, and industries in this country, rich in coal resources and enjoying oil from the North Sea oil field. France's efforts include biomass exploitation. In its development efforts, importance is attached to home heating, hot-water supply, and biomass. Next comes the conversion into power of solar energy. Photocells are also a subject of research and development. (NEDO)

  17. Survey and research achievement report for fiscal 1980 on patent and information under Sunshine Program. Survey of information on new energy technology development (Solar energy); 1980 nendo tokkyo joho chosa kenkyu seika hokokusho. Shin energy gijutsu kaihatsu joho chosa (taiyohen)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Solar energy as defined by the United States includes hydroelectric power, biomass, and the ocean. The short-term strategy deals with passive solar air-conditioning, hydroelectric power, and biomass direct combustion. The medium-term strategy involves positive heating and wind power. The long-term strategy covers heat for agriculture, photovoltaic power, and OTEC (ocean thermal energy conversion), and the ultralong-term strategy covers power generation in space and photochemical conversion. Canada is behind other countries in the conversion of solar energy into power, and solar energy is used but passively as heat source, this because this country is rich in other resources. In West Germany, solar energy may be exploited for hot-water supply and heating at high latitudes, but it is not likely that it will be used for power generation. Home heating offers some appeal since potential demand for it is great. In Britain, the use of solar energy is not a pressing matter, this because systems for effective use of coal have long been established at homes, society, and industries in this country, rich in coal resources and enjoying oil from the North Sea oil field. France's efforts include biomass exploitation. In its development efforts, importance is attached to home heating, hot-water supply, and biomass. Next comes the conversion into power of solar energy. Photocells are also a subject of research and development. (NEDO)

  18. 17th Business Report Meeting of New Energy Industrial Technology Development Organization (NEDO). Section Meeting on Solar Technology; Dai 17 kai jigyo hokokukai. Taiyo gijutsu bunkakai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    In this section meeting, reports were made on the following themes: 1) outline of NEDO solar technology development; 2) commercialization study of thin film polycrystal solar cell production technology; 3) development of CdTe solar cell module production technology; 4) R and D of construction material monolithic solar cell modules; 5) development of the project overseas for solar energy technology development. In 1), outlined were the development of commercialization technology of photovoltaic power system, internationally joint demonstration development of photovoltaic power system, development of production facilities of solar cell use compound semiconductors, development of commercialization technology of solar system for industrial use, etc., and a large wind power system. In 2), the results of the study 'low cost Si substrate production by continuous cast method' were reported. In 3), the results were reported of the increase in efficiency and development of low cost production technology for large area modules. In 4), 3 kinds and 6 systems of R and D for house roofs and building walls were conducted, and possibilities of commercialization were obtained in terms of performance and economical efficiency as construction material. In 5), with the use of natural conditions and social systems in Nepal, Mongol, Thailand and Malaysia, the development for commercialization of this system is being made by joint research with each country. (NEDO)

  19. Achievement report for fiscal 1981 on Sunshine Program survey and research. Joint projects on solar energy between Japan and Australia, etc. (Joint efforts for high-grade flat-plate collector development); 1981 nendo Nichigonado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichigo taiyo energy gijutsu kyoryoku (kokyu heiban collector kaihatsu kyoryoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Investigated at DET (Division of Energy Technology) are a unit for controlling air convection in between a heat collector heat-collecting plate and the cover, testing methods, and under-floor heat accumulation using a horizontal rock bed. DMC (Division of Mineral Chemistry) is engaged in the study of black Ni selective absorption film formation on a metal plate and a reflection-preventing film for a heat collector. Monash University studies methods for testing heat collectors, transfer of heat, heat pipe, tracking mechanism, etc. Melbourne University is dedicated to computer model calculation involving solar energy utilization. Sydney University deals with collectors, selective absorption films, absorption type refrigerators, heat accumulation, and desalination of water. Under study at New South Wales University are passive solar systems, photothermal collectors, solar cells, etc. The Beaseley Corporation is a manufacturer of heater collectors and water heaters in South Australia, and a visit is paid to the corporation for the study of its manufacturing process. The Rheem Corporation manufactures water heaters in New South Wales, and its presence in the solar collector industry is known. (NEDO)

  20. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Survey and study of analysis of commercialization of solar-grade silicon material manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Taiyodenchiyou silicon genryo seizo gijutsu no jitsuyoka kaiseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The trend of technology development, problems harbored therein, trend of the market, and the like were investigated for supporting the development of technologies for the mass production and commercialization of solar-grade silicon materials. Concerning the future of production enhancement and cost reduction in the manufacture of polycrystalline silicon solar cells, studies were made from the technological viewpoint. The results are shown below. It is estimated that approximately 4,500 tons of material silicon will be necessary in 2005 and 6,500-10,700 tons in 2010. Since the melting purification method of NEDO (New Energy and Industrial Technology Development Organization) now under development step by step toward commercialization as well as the conventional source will provide the necessary amount of material silicon, it is inferred that the development of solar cells will go on without any restraint originating in the semiconductor industry. With the commercialization of the technologies so far developed and the development/commercialization of the fast-acting high-performance solar cell technology, probabilities are high that the polycrystalline silicon solar cell manufacturing cost in 2010 will be as low as to be on the 100 yen/W (93-118 yen/W) level which is the level now held up as the goal. (NEDO)

  1. Fiscal 2000 achievement report. Development of energy use rationalization-oriented silicon manufacturing process (Development of silicon substrate manufacturing technology for high-quality solar cell); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko kyodo kenkyu gyomu seika hokokusho. Energy shiyo gorika silicon seizo process kaihatsu (Kohinshitsu taiyodenchiyou silicon kiban seizo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted for enhancing productivity and energy conservation by rendering continuous and automatic the electromagnetic casting process for manufacturing polycrystalline silicon substrates for solar cells. In the manufacture of ingots for substrates by continuous electromagnetic casting, the chuck type system for feeding power to the melt plasma was replaced by a roller type system, and the power feeding position was moved to the high temperature region. Also, an on-line ingot slicing technique was established. In the manufacture of substrates at a slicing rate of 300 {mu}m/minute, productivity of 115,000 wafers/month, yield of 98%, and thickness tolerance of 30 {mu}m were achieved. A high-speed cleaning technique was developed using a jet stream, by which the cleaning time was reduced to 5 minutes and the slurry recovery rate was elevated to 95%. Based on these, substrate-related costs in the case of 100 MW/year production was calculated, which resulted in a cost of 98.8 yen/wafer (target: 103.3 yen/wafer) for manufacturing 15 cm square substrates from ingots and in a 15 cm square substrate slicing and cleaning cost of 135.1 yen/wafer (target: 135.4 yen/wafer). (NEDO)

  2. Report on the FY 1999 results of the development of the wide area energy utilization network system - Eco/energy urban system. 2/2. Study of the systematization technology/evaluation technology out of the study of the energy system design technology (Study of the application method of element technology/system and trial calculation of the introduction effect); Koiki energy riyo network system kaihatsu (eco energy toshi system). 2/2. Energy system sekkei gijutsu no kenkyu no uchi system ka gijutsu hyoka gijutsu no kenkyu 1999 nendo seika hokokusho (zenkoku no netsu juyo no bunpu jokyo chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of smoothly introducing the equipment technology and system technology being studied in the development of element technology in the eco/energy urban project, the paper conducted the study of conditions/application method in applying the technology to the actual energy supply system, analysis of the introduction effect, arrangement of the subjects on technical development, etc. In the study, for the methanol/hydrogen base technology, heat pump technology, heat recovery technology, heat transport technology and heat power generation technology, the quantitative analysis was made in terms of the lifecycle energy consumption amount, lifecycle CO2 emission amount and lifecycle expenses. As to the methanol base system, the subject is the reduction in auxiliary power. Concerning the heat pump technology, the subject is the enlargement of simple equipment. As regards the heat recovery technology, the subject is the development of system with long useful year. Relating to the heat transport technology, subjects are the completion of the menu of large-diameter piping in the vacuum thermal insulation heat transport piping system, and reduction in conveyance power of heat medium. About the heat power generation technology, subjects are the stability/durability of the system. (NEDO).

  3. Reports on 1981 result of Sunshine Project. Research on conditioning required for industrialization of new energy technology (summary); 1981 nendo shin energy gijutsu kigyoka ni hitsuyona joken seibi ni kansuru chosa kenkyu. Yoyakuhen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In order to decide measures for introducing new energy to the society, the work starts from the investigation of the present state of energy demand, examining feasibility of introducing new energy into the state, and then assuming concretely the circumstances in which new energy is brought into the society to some extent. In the subject research, with 1990 set as a target year, the following examinations are carried out for the purpose of estimating the state of introducing new energy to the Japanese society at such point in time. (a) Feasibility is studied of substituting with new energy on oil users' part at present, with an estimate made on the state of new energy introduction in fiscal 1990. (b) An energy flow analysis is made for the purpose of checking interrelation between the total energy demand structure in Japan and the quantity of introducing new energy as of 1990. (c) On the basis of these results, current various energy-related laws and regulations are reviewed, with policies examined for introducing and promoting new energy. (d) On-site investigation is conducted on relationship with the energy policy of coal producing countries, in the case where a coal liquefaction plant is constructed in such countries and where overseas operations and imports of liquefied oil production are implemented. (NEDO)

  4. Fiscal 1998 research report on the R and D on industrial science and technology for creating new industries. R and D on intelligent material and structure systems (Development of practical technology for rational use of energy); 1998 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a part of development of intelligent material/structure systems, study was made on practical technology for rational use of energy. For resource saving and energy saving (smartening) for large and complex machines and structure systems, light-weight long-life materials/structures are indispensable. Study was thus made on the basic technology of material/structure systems equipped with realtime defect detection function, structural integrity diagnosis function and control function of noise and vibration through information processing and control by integrating composite material/structure and fiber or film sensor material/device. For development of smartening technology, sensing technology was studied to detect the interior structure of composite material/structure compacts. The basic fabrication technology of ceramic actuator materials/devices, and shape memory alloy system actuators were put into development. Smooth connection and cooperation among groups were promoted through the technical committee and research on domestic and overseas trends for forming common knowledge. (NEDO)

  5. Fiscal 1997 survey report. Subtask 9 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (survey/study on the innovative and leading technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 9 kakushinteki, sendoteki gijutsu ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the purpose of giving useful suggestions/proposals to the course of WE-NET and contributing to the R and D, conducted were survey/collection/evaluation of new technologies. The paper described the fiscal 1997 results. The number of the proposals of new technology accumulated during fiscal 1993 to 1997 is 28. The proposals of new technology made in fiscal 1997 are hydrogen production effectively using solar energy by wavelength zone, hydrogen storage using fullerene, and the methanol power generation turbine system. Four technologies proposed in fiscal 1996 and 1997 were evaluated. The evaluation method requires two steps of the marking using the analytic hierarchy process (AHP) and the adjustment by the committee. The highly evaluated proposals out of those having been made were analysis/evaluation of hydrogen-oxygen internal-combustion Stirling engine, hydrogen production effectively using solar energy by wavelength zone, hydrogen production by solid oxide electrolysis, magnetic refrigeration method for hydrogen liquefaction, hydrogen production technology using photocatalyst, etc. The paper also stated the result of studying concepts of innovative/leading technologies in fiscal 1996. 4 figs., 29 tabs.

  6. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 8. Development of hydrogen production technology; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu seika hokokusho. 8. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was carried out to establish a hydrogen production technology in the electrolysis of water using the solid macromolecular electrolyte method expected to be more efficient and less costly than the conventional hydrogen production methods. In the development of large area electrolysis cell lamination, a lamination comprising ten 2,500cm{sup 2} cells was fabricated, and a value exceeding the target energy efficiency of 90% was achieved. In the fabrication of stacks for hydrogen service stations, a lamination of ten cell stacks of 1,000cm{sup 2} was built, which achieved energy efficiency of not less than 90% at the an electrolysis temperature of 100 degrees C. A hydrogen production plant conceptual design was prepared under the conditions of hydrogen generation amount: 10,000Nm{sup 3}/h, electrode area: 10,000cm{sup 2}/cell, current density: 2.5A/cm{sup 2}, operating temperature: 120 degrees C, cell voltage: 1.705V, total number of cells: 976, stack constitution: 122/stack, and the number of stacks: 8. The result of studies placed the plant construction cost at 2.18-billion yen including building and civil engineering costs, and the hydrogen production unit cost at 28.4 yen/Nm{sup 3}. (NEDO)

  7. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 8) - development of hydrogen production technology; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 8. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    R and D was conducted with the view of establishing hydrogen production technology based on the solid high polymer electrolyte water electrolysis method, which presumably offers higher efficiency and lower cost than conventional methods. This year, as well as implementing development of large-scale cell lamination (electrode area 2,500 cm{sup 2}, 10 cells) by using two hydrogen production methods (electroless plating method and hot press method), work was started for developing cells (electrode area 1,000 cm{sup 2}) for hydrogen stations. In the research on longterm durability improvement, with a 50 cm{sup 2} membrane electrolyte or cell, the evaluation test results were obtained of stable electrolytic performance showing more than 93% energy efficiency after 400 hour operation, under the conditions with electrolysis pressure 0.4MPa and electrolysis temperature 120 degree C. In a test of 1,000 cm{sup 2} prototype cell for hydrogen stations, the evaluation result was obtained for energy efficiency of 92% under the conditions with electrolysis pressure 0.5MPa and electrolysis temperature 120 degree C; thus, this year's target efficiency of over 90% was achieved. Further, enhancement of the quality was contrived for example by improving the electroless plating method and remodeling a roll press machine. (NEDO)

  8. Fiscal 1994 achievement report. Development of photovoltaic power generation system practicalization technology - Development of ultrahigh-efficiency solar cell technology (Development of new photoelectric conversion material technology - Research on future feasibility of wet-type solar cells); Taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Chokokoritsu taiyo denchi no gijutsu kaihatsu (shinkoden henkan zairyo no gijutsu kaihatsu (shisshiki taiyo denchi no shoraiteki kanosei no chosa))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-03-01

    A survey is conducted of wet-type solar cells that may constitute an important field in solar chemistry. The wet type solar cell made known by Graetzel et al. in 1991 is a combination of ultrafine TiO{sub 2} grains and a sensitizing dye. The ultrafine grain surface structure enlarges the area of an electrode for the absorption of 46% of incident solar radiation of which 80% or more is converted into electric power. The fill factor at 520nm of a cell fabricated for an additional test turns out to be 40% against the 76% mentioned in technical literature, and the conversion efficiency 10%. The Titanyl sulfate is also tested because it is low in price as material for titanium oxide. Functional groups are experimentally introduced for the generation of bonds on the substrate to be effective in the injection of a sensitizing dye. A sensitizing dye with two carboxyl groups and two bipyridine rings as ligand is allowed to be supported by TiO{sub 2}. IR (infrared) spectrometry is performed, and then formation is found of ester-like bonds or chelate bonds due to the interaction of carboxyl groups and the substrate surface. This is enhanced by surface treatment. (NEDO)

  9. Save energy of 21{sup st} century in public welfare section. Practical technology and future prospect; Minsei bumon ni okeru 21seiki no sho energy. Jitsuyoka gijutsu to shorai tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Nakagami, H. [Jyu Kankyo Research Inst., Inc. Tokyo (Japan)

    1998-01-01

    Only 2 years left for 20th century. This 100 years, population increased 3 times, actual GNP became 42 times higher, energy consumption was increased to 52 times and amount of CO{sub 2} generation has been 31 times higher. Even at present after 20 years of second oil chock, consumption of energy and amount of CO{sub 2} generation are in a increasing trend. Among them, in public welfare section, energy consumption is increasing along with the transportation section. In residence, increase in energy demand is due to the improvement of residential environment, wide application of home electrical appliances, and increase in official energy demand is due to wider floor space, wide use of OA equipments, automatic vender machines. On the other hand, energy saving of air conditioning, refrigerator, television and so forth has been progressed widely. However, progress of these save energy technologies also is not sufficient to cope with the speed of energy consumption. Results differ with the progress of technology development, speed of its wide use and so forth, however, reduction of generation of CO{sub 2} to a 1990 level in public welfare section is very difficult. General measures like perfect technology development, economical aid, advertisement and so forth are in demand

  10. FY 1998 survey report on the basic study of a possibility of cooperation in new energy technology in China; 1998 nendo Chugoku ni okeru shin energy gijutsu kyoryoku kanosei kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The development and utilization of new energy and reusable energy in China have greatly progressed for these 20 years, but it is necessary to further enhance the rate of these energy in the energy structure by heightening the conversion efficiency and reducing the production cost. As to the matured technology, it is necessary to attempt a large scale modernization and form a completed production/service system by making large breakthrough of new technology/new industrial art. For improvement of levels of a lot of new energy technology, emphasis should be placed on international cooperation, R and D, and model business. Together with the introduction of reusable energy such as photovoltaic, wind, geothermal and ocean power, the conventional low efficiency biomass utilization system is converted one after another. The development/spread of clean coal technology are promoted, and the rate of the hydroelectric/atomic power generation is heightened. By 2010, the full-scale application/spread of new energy technology should be advanced, and the technology and production of the world top level should be realized. It is necessary to make the energy consumption clean and promote the continuously harmonized growth of economy, society and environment. (NEDO)

  11. Fiscal 2000 achievement report on research and development of industrial technologies. Research and development of synergy ceramics (Development of energy use rationalization technology); 2000 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts are made to develop self-complete type purification ceramic materials in which selection, separation, and purification functions are merged with the energy conversion function. Activities are conducted in the three fields of developing (1) materials derivation technology, (2) application technology, and (3) common base technology. In relation to selection, separation, and purification functions in field (1), studies are made about electrochemical cell structure control and cell constituting materials for enabling a high efficiency NOx purification reaction. As for the energy conversion function, studies are made about the improvement of characteristics of oxide based thermoelectric conversion materials and about changes in electrical output due to their development into cells. In a study of novel thermoelectric conversion materials, K{sub 2}NiF{sub 4} type Y{sub 0.33}Sr{sub 1.67}(Ni{sub 1-y}Co{sub y})O{sub 4-{sigma}} and Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 1-y}M{sub y})O{sub 4-{sigma}} (M=Fe, Co) are synthesized, and electrical resistivity levels and Seebeck coefficients are determined at room temperature-800 degrees C in an oxygen current. Seebeck coefficients are found to be negative for all specimens, which shows that they are n-type conductors. Ce{sub 0.25}Sr{sub 1.75}(Ni{sub 0.7}Fe{sub 0.8})O{sub 4-{sigma}} exhibits the greatest output factor of 0.064 times 10{sup -4}Wm{sup -1}K{sup -2} (400 degrees C). (NEDO)

  12. Achievement report for fiscal 1982 on Sunshine Program. Survey and research on preparation of conditions for industrializing new energy technologies; 1982 nendo shin energy gijutsu no kigyoka joken seibi ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    Examined in this report are problems related to new energy that may arise in the energy supply/demand environment in 1990 when new energy will be introduced. This report consists of Chapter 1 about problems to solve before the introduction of new energy into the fields of industry and transportation, Chapter 2 about the analysis of a model of the supply/demand structure and ripple effects of the introduction of new energy technologies, and Chapter 3 about the analysis of laws and systems for the introduction of new energy technologies. In this research, concrete systems for utilization are presumed, and problems are sought out based on these presumed systems. Several utilization systems for each of the technologies are placed against the demands in the fields of transportation and industry, and problems in presence in this process are sought out, and examined. Viewpoints mentioned below are taken into consideration when seeking out problems. The viewpoints are (1) the establishment of technologies to utilize, (2) problems in the legal system, (3) problems about siting, and (4) problems in accelerating new energy diffusion. Chapters 1 and 2 deal with analyses based on Viewpoint (1), and Chapter 3 deals with analyses into problems sought out based on Viewpoints 2-4. (NEDO)

  13. Reports on 1981 result of Sunshine Project. Research on conditioning required for industrialization of new energy technology; 1981 nendo shin energy gijutsu kigyoka ni hitsuyona joken seibi ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    This research was intended to establish foundation for the coming new energy era, by clarifying all interfering elements and taking counter measures, in further spreading and promoting the new phase of new energy technology development under the Sunshine Project. With the public section as the main body, studies were made in the technological aspect as well as the legal/institutional aspects, and also an investigation was conducted of the cases of introducing new energy from overseas. In the subject research, with 1990 set as the target year, the following examinations were carried out for the purpose of concretely estimating the situation of introducing new energy into the society in Japan at such point in time. The examinations were to study the feasibility of substitution with new energy in fiscal 1990 on the present level of oil consumption; to extract problems on the basis of the results and examining a policy of introducing and promoting new energy; and, to investigate on the spot, as a case study in building a coal liquefaction plant in a coal production area overseas, a relation with the energy policy of the producing country in implementing the overseas operation and importation of liquefied oil so produced, etc. (NEDO)

  14. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 3. Study on the global network; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 3. Global network kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the WE-NET project, the introduction condition of hydrogen as substituting energy and CO2 reduction effect were analyzed using a global energy model. The WE-NET project aims at global-wide introduction of clean energy by converting abundant renewable clean energy into hydrogen transportable to distant consumers all over the world. The study result in fiscal 1996 is as follows. Undeveloped hydroelectric resources in the world are estimated to be 12 trillion kWh/y equivalent to the existing developed one in the world. Since the cost of the hydroelectric power generation projects over 1000MW in the planning stage is estimated to be 0.02-0.05$/kWh lower than that of other renewable energies, such projects are expected as energy source in the initial stage of the practical WE-NET project. The GREEN model was modified by adding a hydrogen analysis function, and extending an analysis period. The modified model allowed evaluation of the long-term important role of hydrogen energy, in particular, the capability of CO2 gas reduction all over the world. 28 refs., 92 figs., 56 tabs.

  15. FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 9. Research and evaluation of innovative and leading technologies; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 9 (kakushinteki, sendoteki gijutsu ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to make useful suggestions and proposals for the International Clean Energy Network Using Hydrogen Conversion (WE-NET) project and thereby to promote the research and development activities, the innovative and leading technologies have been studied, investigated and evaluated. In FY 1998, a total of 6 proposals were collected, and evaluated to prioritize for the conceptual studies. These are related to methanol-fueled power generation turbine system, conceptual design of high-efficiency production system for high-efficiency solar cell by the 10 GW/y scale production process, investigation of potential of wind power, CO2 recycling methanol fuel cell, investigation of catalysis materials for hydrogen combustion and catalytic combustion systems, development of reversible high-temperature steam electrolysis cell/solid oxide fuel cell by the synthesis from aqueous solutions, and mobile heat recovery hydrogen production system. Promising technologies to be reflected on the WE-NET project were examined, based on the new technologies acquired from the research and investigation so far. As a result, two candidates were selected; hydrogen liquefaction by magnetic refrigeration technology, and catalytic combustion gas turbine. (NEDO)

  16. FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 6. Development of cryogenic temperature materials technologies; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 6 (teion zairyo gijutsu no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Summarized herein are the cryogenic temperature materials technologies for the International Clean Energy Network Using Hydrogen Conversion (WE-NET) project, developed in FY 1998. The R and D programs have been implemented continuously since 1994. For stainless steel, the base and TIG weld metals were evaluated for their material characteristics in liquid hydrogen. The items investigated included the influences of hydrogen charge, 20% of stretch working on the base metal, welding methods, and ?-ferrite content on the characteristics. Fatigue strength of the base metal was found to increases as temperature decreases, but remain unchanged in a range from 20 to 77K. No significant difference was observed between 304L and 316L. For aluminum alloy, mechanical characteristics, centered by fatigue characteristics, were investigated for the base and weld metals. The sample of higher tensile strength showed a higher fatigue strength, at room temperature, 77 and 4K. The other tested items investigated included embrittlement characteristics in a hydrogen atmosphere, phase transformation, hydrogen diffusion and fracture toughness, for establishing the databases of cryogenic temperature materials. (NEDO)

  17. Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

  18. FY 2000 report on the results of the research and development project for new industry creation type industrial science technologies. R and D of the intellectual material and structural systems (Development of technologies for rational use of energy); 2000 nendo shinki sangyo soshutsugata sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Chiteki zairyo kozo system no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Described herein are the FY 2000 results of the R and D project for development of intellectual materials and structural systems, as part of development of technologies for rational use of energy. The program for development of health monitoring technologies produces the bright prospects for commercialization of the fine FBG (Fiber Bragg Grating) sensor which can be embedded in a CFRP prepreg, and establishes the crack detecting method. The program for development of smart manufacturing technologies describes the dielectric constant sensor capable of monitoring the curing process, detection of the cured conditions by the optical fiber sensor, and development of the performs by RTM (Resin Transfer Molding). The program for technological development of the active-adaptive structures conducts the vibration- and noise-controlling tests for the small-size structural elements, confirming that the damping coefficient is improved by at least 20% and acoustic power is reduced by at least 30%. The program for developing the actuator materials and elements improves the piezoelectric characteristics of the PZT-based materials by hybrid sintering, and develops the actuators of high-durability FGM (Function-Gradient Materials). It also develops the foil- and belt-shaped shape memory alloys by arc-aided dissolution and rapid solidification of Ti-Ni-Cu-based alloys. (NEDO)

  19. Development in fiscal 1998 of technology to put solar systems for industrial use into practical use. International joint technology development for solar energy utilization systems; 1998 nendo sangyoyo nado solar system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyo energy riyo system kokusai kyodo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The solar energy utilizing technologies having been developed under the Sunshine Project were used to have executed the international joint technology development on the 'solar heat utilizing drying system' in the Republic of Indonesia. This paper summarizes the achievements in fiscal 1998. In operating the pilot plant, three operational experiments out of seven experiments were carried out only by Indonesian engineers. As a result of the drying experiments, the heat collecting characteristics of the collector were as about half at 19 to 30% as the efficiency assumed in the design of 50%. The reason for this can be attributed to the fact that the cover glass used in the demonstration test in Japan had light permeability of about 87%, but the cover glass used in the test plant was made of frosted glass whose light permeability was about 37%. This glass is the only glass available for a heat collector in the solar heat hot water device in Indonesia, but is unsuitable for the heat collector. Another cause was that the insolation at the site was lower by about 30% than the one used at the design stage. (NEDO)

  20. FY 2000 report on the results of the R and D of 'frontier carbon technology.' Development of the technology to rationalize energy utilization; 2000 nendo 'tansokei kokino zairyo gijutsu' no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-05-01

    This report summarized the FY 2000 results. In Chapter 1, development of electrically high functional diamond process technology, electric characteristics which frontier carbon materials have were made clear by the following four subjects, and the development was executed of original production process technology for realizing energy saving by heightening efficiency of electric devices, displays, etc. 1) development of morphology control; 2) development of technology to control electron emission characteristics; 3) development of technology to control oriented growth; 4) development of technology to enlarge single crystals. In Chapter 2, the basement technology of electron emission control was studied. Namely, conditions for film formation were investigated to elucidate the formation mechanism of carbon nano structure films by Dual RF CVD method, IPC CVD method and thermal CVD method. As to the electron emission mechanism of diamond, electron emission characteristics were outlined of the boron dope diamond thin film formed by micro wave plasma CVD method in FY 1999. In Chapter 3, investigational study of original production process technology of electrically high function materials, test study was made of the element technology needed to make high quality/large area diamond substrates. (NEDO)

  1. Fiscal 2000 technology trend survey. Survey of technology trend relating to next-generation metal-based material compatible with inverse manufacturing leading to energy use rationalization; 2000 nendo gijutsu doko chosa hokokusho. Energy shiyo gorika ni kakawaru inverse manufacturing ni tekigoushita jisedai kinzoku kei zairyo ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the construction of a recycling system consuming less energy and therefore higher in efficiency, studies were made about the feasibility of metallic material developing/recycling systems more congruent with the objective through the application of inverse manufacturing (IM). Concerning metallic materials and recycling technologies, steel, aluminum alloys, and magnesium alloys were taken up, and a survey was made of hazardous elements in steel materials, unification of materials to constitute aluminum alloy parts, yield of magnesium in die casting, and the like. In the survey of recycling of automobiles, it was pointed out that the treatment of resin-based shredder dust was posing problems and that the use of metallic materials high in recyclability was essential to IM. In conclusion, three propositions were presented, which involved technologies for the advanced use of magnesium alloys as materials leading to the realization of IM, the development of recycling-oriented general-purpose alloys (with Mg and Al as mother metals), and the development of functional bonding technology enabling debonding (debondable bonding technology). (NEDO)

  2. FY 1999 report on the results of the research and development project for new industry creating type industrial science and technology. Innovated casting simulation technology (Development project for commercialization of technologies related to rational use of energy); 1999 nendo kakushinteki chuzo simulation gijutsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Described herein are the results of the FY1999 research and development project, implemented for development of the casting process simulation technologies, with the objectives to improve efficiency and energy-saving for the various industrial areas, e.g., industrial machines, aircraft, automobiles and vehicles, and power generation plants. For development of the mold filling and solidification process simulation programs, the efforts are directed to development of the fundamental algorithms for simulation of unidirectional solidification casting used for, e.g., turbine blades, and also to the basic works for validation of the programs. For development of the solidification structures and defect formation simulation programs, the fundamental works are done for simulation of solidification structures and channel-type segregation, which are the main problems for columnar blades, to predict the defects formed in, e.g., turbines. For development of the related measurement techniques, investigations are made for evaluation of the levitation characteristics of nickel alloys by the electromagnetically levitated droplet method and problems involved therein, prior to the tests in the the underground microgravity test center. (NEDO)

  3. Fiscal 1997 survey report. Subtask 4 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen production technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 4 suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    As a WE-NET subtask, a study has been conducted of the solid polyelectrolyte water electrolysis method by which higher efficiency and lower cost hydrogen production is expected than in the conventional hydrogen production method. Production methods of electrode, electrolyte, etc. were studied. In the electroless plating method, the manufacturing process of membrane-electrode assemblies was realized in a large area of 2500 cm{sup 2} by the porous-surfaced method by studying manufacturing conditions for slurry membrane/membrane assembly/electroless plating processes. In the hot-press method, the refining degree and dispersibility of iridium dioxide powder were studied to improve characteristics of anode catalyst. A method was developed to form polyelectrolyte coatings homogeneously on the surface of electrode layer catalytic powder, and a large area of 2500 cm{sup 2} was realized. Beside the performance test using large single cells, FS was conducted to discuss optimum operating conditions and optimum structures of plants. Both methods indicated the performance exceeding the energy conversion efficiency of 90%, a WE-NET target, at current density of 1A/cm{sup 2} and electrolysis temperature of 80degC. A key was found to a bench-scale development (electrode area of 2500 cm{sup 2}, about 5 layers) to be planned in fiscal 1998. 136 figs., 50 tabs.

  4. Fiscal 1997 report of the R and D result of industrial science and technology. R and D on synergy ceramics (development of rational energy use technology); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For rational use of energy resources, the process technology which allows harmonization and multiplication of conflicting characteristics was developed for development of new ceramic system materials. This paper summarizes the result in fiscal 1997. On a structural reaction process among creation technologies of ultra-reliable structure, study was made on structure control and hot-working technology through atmosphere control in ceramics synthesis. On basic technology for analysis and evaluation, study was made on the effect of particle bridging on strengthening and toughening of ceramic materials. Study was also made on a toughness expression mechanism, FEM model analysis of particle bridging, and crack growth resistance of ceramics. On control of solid solution precipitation, new alumina ceramics with high strength, hardness and wear resistance was obtained by transgranularly precipitating nano-size particles from a fine-grain high-density matrix through an improved particle formation process. Its toughness was considerably improved by controlling grain shape and grain boundary structure. A precipitation mechanism was also discussed. 89 refs., 107 figs., 14 tabs.

  5. 1998 Annual Study Report. Surveys on seeds for global environmental technologies, including those for energy saving; 1998 nendo chosa hokokusho. Sho energy nado chikyu kankyo taisaku gijutsu no seeds ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The energy-saving and other global environmental technologies are surveyed by collecting relevant information from various institutes, both abroad and domestic, to contribute to development of ceramic gas turbines. USA has announced a climate change plan, based on the five principles, to promote utilization of high-efficiency technologies and development of new clean technologies. UK is promoting to improve energy efficiency, along with liberalization of its energy markets. Germany concentrates its efforts in the 'Program for Energy Research and Energy Technologies.' France places emphasis on prevention of air pollution and rational use of energy. The R and D trends at public institutes, e.g., universities, for global environmental technologies are surveyed, from which a total of 14 themes are extracted as the seed technologies. At the same time, a total of 9 techniques potentially applicable to the seeds are extracted by mainly reviewing JICST and patent information, and assessed. The R&D trends of the IPCC-related researchers are also surveyed, but provide no theme directly applicable to the seeds. Most of the related themes at the private and public institutes surveyed, both domestic and abroad, are concentrated on carbon dioxide. (NEDO)

  6. FY1998 survey on preparation of data collection related to new energy technology development (cogeneration); 1998 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa (cogeneration) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    New energy technologies have had the subsidy institutions established in association with advancement of the technologies, and such introduction promoting measures developed as the introduction assistance and advisory project. To promote this development more effectively, it is necessary that different data related to new energies are put into order comprehensively and systematically to be retained as the basic data. Therefore, this paper collects and puts into order the latest published data on cogeneration from among other new energy technology areas, with main regard to system listing, specific introduction examples, subsidy institutions, and how other countries are working on the technologies. Hydroelectric power generation uses up head energy of water by installing power plants along a river from higher location to lower location. Similarly the cogeneration is a kind of multi-stage energy utilization (cascade utilization) system that uses up energy serially from as high oil and natural gas combustion temperature as 1,500 degrees C or higher down to temperature levels used for hot water supply and air conditioning as low as 45 to 50 degrees C. It generates electric power by using a thermal engine, and utilizes waste heat effectively. (NEDO)

  7. Load leveling air conditioning technology development by unused energy high-level utilization. Summary of lectures given at the achievement report meeting; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu kaihatsu. Seika hokokukai koen yoshishu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-01-01

    This paper summarizes lectures given at the research and development achievement report meeting on load leveling air conditioning technologies utilizing unutilized energies at high levels. The lecture titled 'the current status and future problems in heat supply industries' given by the manager of the Heat Supply Industry Department at the Agency of Natural Resources and Energy explained the heat supply businesses in relation with global environment issues, electric power load leveling, and cogeneration. The lecture titled 'improvement of cities to energy saving type cities and district air conditioning systems' given by a construction official at the Ministry of Construction explained the guideline (draft) for introduction of district air conditioning systems as to their purpose, positioning, procedure for discussing the introduction, and procedure for its implementation as a business. The lecture titled 'the recent trend inside and outside the country around unutilized energies' given by Professor Tanazawa at the Tokyo University of Agriculture and Technology described the intensification of energy problems, environment problems, and the near future measures to be taken against these problems. The lecture titled 'summarization of the achievements in development of load leveling air conditioning technologies utilizing unutilized energies at high levels' given by Professor Nakahara at the Kanagawa University explained the summary of the achievements in research and development by themes. (NEDO)

  8. Report on the basic survey on the commercialization of innovative energy technology in the Tibet district; Tibet chiku ni okeru kakushinteki energy gijutsu jitsuyoka no jisshi ni kansuru kiso chosa report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A field survey was conducted with the aim of commercializing innovative energy technology in the Tibet district. The survey included the energy supply/demand situation and supply plan and the situation of new energy utilization in the Tibet district. And, based on the concrete circumstances in the Tibet district, a realistic plan was presented for solution to the energy supply/demand problem. To carry out the project, used are a lot of solar energy and wind power energy resources which are abundant in Tibet. In about 5 years, 100 sets of village use system and 80,000 sets of household use system are to be installed, which solves the problem on electric power demand in a part of the non-electrified houses. Accordingly, farmers/stockbreeders living in the non-electrified region will alter their life patterns which are closed and behind other countries, get out of the poverty, basically enhance the quality of life, promote the communication of various knowledge/information of scientific technology, renew their life/production concepts, and heighten the production efficiency for the wealthy society. The project itself belongs to the construction for protection of ecological environment. It produces no exhaust gas/solid waste which do harm to the environment. The ecological environment efficiency is very high. (NEDO)

  9. Worldwide clean energy system technology using hydrogen (WE-NET). Interim report of the research and development in Phase 1; Suiso riyo kokusai clean energy system gijutsu (WE-NET). Daiikki kenkyu kaihatsu chukan seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-01-01

    Large scale and effective utilization of renewable energy including hydroelectric power, photovoltaic power, and wind power which are abundant on the earth can contribute to the solution of global environmental issues as well as the release of energy demand and supply. Hydrogen can be produced from the renewable energy, and is converted, transferred and stored if necessary. Such hydrogen can be used in various fields for power generation, fuel for transport, and city gas. In order to establish the technology by which worldwide energy network can be introduced for wide range of fields, conceptual design of a total system has been conducted, and elemental core technologies have been developed. Conceptual design of a practical scale system (total system) including a wide range from production of hydrogen to its utilization has been conducted, and its constitution has been illustrated. In addition, the energy balance and cost of hydrogen have been calculated and analyzed as a trial. Hydrogen production technology, transport and storage technology, and hydrogen utilization technology are introduced as individual elemental technologies. Research results of innovative and leading technologies obtained in FY 1996 are reviewed. 80 figs., 56 tabs.

  10. FY 1974 Report on results of Sunshine Project. Feasibility study on techniques for measuring energy of gases spouting out of volcanoes; 1974 nendo kazan funen energy sokutei gijutsu ni kansuru feasibility study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    It is estimated that energy released from volcanoes all over the world totals 4 times 10{sup 24} erg annually. According to some observed results, an individual volcano releases energy of about 10{sup 23} erg during the active period, and about 10{sup 22} to 10{sup 23} erg in the quiet period. There are many mechanisms involved in release of volcanic energy, but most of the energy is associated with vapors and gases released from the summits. Therefore, quantitative analysis of the thermal energy released from a volcano is one of the essential approaches to elucidate the thermal conditions within the volcano. However, these observations have been scarcely made so far. This R and D project has confirmed applicability of laser radar to measurement of density of released vapors and gases, of supersonic waves and infrared ray to measurement of temperature, of laser Doppler, supersonic waves and infrared ray to measurement of speed, supersonic waves to measurement of shapes, and supersonic waves to measurement of position of flying objects for sampling. It is necessary to decide what techniques should be developed first. (NEDO)

  11. Investigational study of evaluation of the global energy system as a global environmental protection technology; Chikyu kankyo taisaku gijutsu toshite no global energy system no hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    With relation to some global energy systems of which viability is predicted in the future, an evaluation was conducted from the viewpoints of economical efficiency, energy balance, CO2 emission, etc. The fossil fuel CO2 capture system, the conventional thermal power plant added with CO2 recovery/treatment facilities, is expected to reduce approximately 70-75% of the CO2 emission. The fossil fuel decarbonated hydrogen system, which decarbonates fossil fuels, recovers/treats CO2 at the place of fuel supply and uses as hydrogen, is of poor practical application from an economical point of view. The fossil fuel methanol synthesis system, which synthesizes methanol from fossil fuels at the place of fuel supply, generates electric power and recovers/treats CO2 with the methanol, is large in energy loss and CO2 emission and low in overall efficiency and CO2 reduction effect at the time of methanol synthesis. The renewable energy hydrogen system is an ultimate system with no emission of CO2, though it costs much. 110 refs., 83 figs., 107 tabs.

  12. Research report of FY 1996 on development of new hydrogen energy demonstration technology. 2. Results in the extension period of FY 1996; 1996 nendo kenkyu hokokusho. Shinsuiso energy jissho gijutsu kaihatsu (1996 nendo kikan enchobun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The purpose of this project is to clarify the possibility of new hydrogen energy as a future energy source. The new hydrogen energy is obtained from the excess heat generation phenomenon through the electrolysis of heavy water using palladium metal as an electrode. The excess heat measurements were conducted through the excess heat confirmation tests using a fuel cell-type electrolytic cell up to November 1997. As a result, it was found that the excess heat measured by the calibration method can not be measured by the flow calorimetric method. In order to investigate the possibility of systematic errors of the both methods, the sensitivity, accuracy and responsibility, and the conditions of the excess heat generation, research activities based on new facts from scientific information and fundamental research supporting projects have been mainly performed. Among these, were performed the excess heat measurement tests by the cataphoresis method, absorption tests by the high-pressure and high-temperature charging method, gas plasma loading, in-situ X-ray detection, and reactant detection tests using Au/Pd/PdO heterogeneous structural body. 5 refs., 59 figs., 9 tabs.

  13. New Sunshine Project for fiscal 1997 on the international cooperation project. Cooperation in solar energy technologies among Japan, Australia and other countries; 1997 nendo new sunshine keikaku kokusai kyoryoku jigyo. Nichigo nado taiyo energy gijutsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes the state of progress in the cooperation in solar energy technologies among Japan, Australia and other country, the memorandum concluded for the new project, and the activity report on the NEDO/MUERI project. The progress in the cooperation in solar energy technologies among Japan, Australia and other country is divided into that of the new project and that of the continued project. The former relates to the start of the long-term endurance test project for photovoltaic solar modules in Oman. The location of the endurance test is the Sultan Qaboos University in the suburb of Muscat. Modules subjected to the endurance test consist of ten modules of five types. The test will be performed on air temperature, humidity, wind directions, insolation on horizontal surface, insolation on slanted surface, ultraviolet ray intensity, module temperatures, and electric characteristics of the modules. The continued project is an outdoor endurance test for the photovoltaic solar modules begun in fiscal 1996, which is executed by the Murdock University Energy Research Institute (MUERI). The endurance test locations were selected at Darwin, Alice Springs and Perth. This paper reports the photovoltaic solar module endurance test and investigation, as well as the periodical consultations as the activity report of the NEDO/MUERI project. (NEDO)

  14. FY 1994 Report on the results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers; 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu saiteki donyu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Described herein are the FY 1994 results of the joint research project for optimum introduction of development of fuel cell technologies for urban energy centers or the like. The necessary economic conditions for introduction of a fuel cell system to be competitive with the conventional system which individually supplies electric power and heat are 250,000 yen/kW as the construction unit cost, 0.10m{sup 2}/kW as the installation area, 5 years as the cell body life, use of an inexpensive fuel gas (2 to 6 yen/Mcal). Moreover, it is an indoor system which shall have the operational characteristics to follow daily demand fluctuations while operating under the optimum conditions in the urban redevelopment area considered. A 5,000kW-class fuel cell plant burning fuel gas (2 yen/Mcal) will need a total floor area of approximately 400,000 m{sup 2} in an energy-intensive office type demand area. These conditions shall be met in order to economically introduce the 5,000kW-class plant. It is also necessary to compare the plant with the competitive cogeneration plants. The specifications for the prototype now under consideration are sufficient for the energy-saving effect, and it is premised that these specifications and characteristics are secured. (NEDO)

  15. Load leveling air conditioning technology development by unused energy high-level utilization. Summary of achievements by development themes; Miriyo energy kodo katsuyo fuka heijunka reidanbo gijutsu kaihatsu. Kaihatsu temabetsu seika gaiyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-01-01

    This paper introduces a number of research and development cases on utilization of unutilized energies. In developing the component technology for a thermal plant utilizing low-temperature unutilized energies, the paper introduces a heat exchanger system to collect heat from sea water, a heat exchanger system to collect heat from waste heated area in subways and urban sewage plants, and a high-density heat transportation system using ice plus water slurry or PCM-C plus water slurry. Furthermore, with regard to the heat pump system using low-temperature unutilized hear sources, development was introduced on a 'heat source load responsive heat pump system', which combines a load variation responsive heat pump utilizing river waters with a latent heat storage system using nighttime electric power serving for electric power load leveling. In developing the component technology for a heat plant utilizing high-temperature unutilized energies, introduction was given on a turbine driven turbo type heat pump system, a high-efficiency absorption type heat pump, a waste heat driven absorption type freezer, and an urban type underground heat storage tank. (NEDO)

  16. Report on fundamental surveys for such as cases and effects in relation with development of new energy technologies in fiscal 1999; 1999 nendo shin energy gijutsu kaihatsu ni kakawaru jirei koka nado kiso chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the fundamental surveys in fiscal 1999 on cases and effects in relation with development of new energy technologies. Among the projects having been performed by NEDO in commemoration of the 20th anniversary of the NEDO foundation, the economic and social situations in the times in which the projects have been carried out with the focus placed particularly on new energies were put into order and analyzed to make clear the positioning of the project significance in the nation's energy policies. In addition, the roles of NEDO were recognized afresh to use them as the fundamental materials to serve for the future policy development. For the past thirty years before and after the oil crises, the time division that can be used universally for the project evaluation was established, based on the trends inside and outside the country, social currents, related indexes, and the status of development execution. Work hypotheses were presented regarding the basic conception in the evaluation, specific evaluation viewpoints, and their contents. Based on the hypotheses, three subjects were taken up as representative cases, that is, photovoltaic power generation, coal liquefaction, and phosphoric acid type fuel cell technology development. Time points that are considered as the important turning points were specified to give evaluations at respective turning points. Analyses were also made on decision making factors for project planning, continuation, direction change, suspension, and completion. (NEDO)

  17. Survey report for fiscal 1998 on the survey on preparation of data collection related to new energy technology development (wind power generation ); 1998 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa (furyoku hatsuden) chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    As a result of heightening consciousness on assurance of energy security and global environment problems in recent years, it is urged in Japan to promote development of technologies to introduce and proliferate new energies, and work on acceleration of the introduction. On the other hand, in order to move forward effectively the introduction promoting project intended of proliferation and enlightenment, it is necessary to put into order comprehensively and systematically the different data on the new energies, and summarize them as the basic data. This report, focusing on a wind power generation system, collects and puts into order the latest published data on the wind power generation system, placing in the center the introduction examples in Japan and other countries, supporting measures, wind power generation system markets, and the specifications of major windmills. The major contents may be summarized as follows: significance of introducing the wind power generation system, the current status of the market, policies in different countries, status of introducing the system in other countries, subsidy institutions for the introduction, the introduction flow, efforts made by government related organizations and local governments, a list of window offices of the related corporations, the fundamental knowledge, and the movements in 1998. (NEDO)

  18. Research report of FY 1996 on development of new hydrogen energy demonstration technology. 1. FY 1996 results; 1996 nendo kenkyu hokokusho. Shinsuiso energy jissho gijutsu kaihatsu (1996 nendo jisshibun)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-11-01

    The purpose of this project is to clarify the possibility of new hydrogen energy as a future energy source. The new hydrogen energy is obtained from the excess heat generation phenomenon through the electrolysis of heavy water using palladium metal as an electrode. The excess heat regeneration tests have been successively conducted using two kinds of electrolytic cells. As a result, the excess heat generation measured by one electrolytic cell in FY 1996 has been confirmed in about 35% of repeatability under the same condition. On the other hand, the excess heat over the measuring accuracy was not measured using two kinds of absolute heating value measuring systems. The electrolytic cell, by which the excess heat was measured, was used for confirming the absolute heating value as keeping its condition. When tests were conducted using the developed system, it was found that the absolute heating value can not be detected. Then, verification tests are currently conducted for determining the cause. Moreover, in order to clarify the basic characteristics of materials required for the regeneration of the excess heat generation phenomenon, observation and analysis of the materials were performed before and after the excess heat measurement. Thus, the cause of difference was revealed. 3 refs., 98 figs., 24 tabs.

  19. FY 1999 report on the results of the superconductive energy application technology development/research on a total system, etc. Survey of potentiality of the commercialization of superconductive technology, effects of the introduction, etc. (Future course of the superconductive technology development in Japan); 1999 nendo chodendo denryoku oryokuyo gijutsu kaihatsu total system nado no kenkyu. Chodendo gijutsu no jitsuyoka kanosei oyobi donyu koka nado no chosa (Nippon ni okeru chodendo gijutsu kaihatsu no kongo no hokosei)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the use of superconductive technology, the following are aimed at: marked reduction in power loss of electrical equipment and power transmission path, and size/weight reduction in electrical devices by high current/magnetic flux density. The superconductive technology has advantages such as great energy saving effect, CO2 reduction and global environmental preservation. As an example, concerning the superconductive generator now being developed under the New Sunshine Project, power loss can be reduced by half, and by the use of high magnetic field, size/weight can be reduced such as reduction in rotor diameter and reduction in weight by half. Further, as an innovative system, cited are the superconducting magnetic energy storage system (SMES) and flywheel energy storage system. The superconducting magnetic levitation railway, medical use MRI, etc. have also innovativity which is difficult to get in the conventional technology. Effects are also expected of introducing the process development using superconducting magnet such as magnetic separation, electromagnetic metallurgy, electromagnetic agitation and monocrytal growth convection control. Also cited is Josephson electronic device. High performance SQUID in bio-magnetic/non-destructive inspection is also expected to be developed. (NEDO)

  20. Summary of research achievements in fiscal 1980 in research and development of new energy technologies (Research and development expense); Shin energy gijutsu kenkyu kaihatsu 1980 nendo kenkyu seika no gaiyo. Kenkyu kaihatsuhi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1980-07-01

    This paper describes the achievements in fiscal 1980 of new energy research at the General Research Institute of Electronics Technologies using the NEDO's development expense. To optimize the heat and electric power composite solar system, analyses were performed on heat production, devices and materials, and economy of the whole experimental facilities of the original model. Fundamental researches are being made on crystalline silicon, thin amorphous film and compound semiconductor solar cells. The solar thermionic generation element producing equipment installed in the previous fiscal year has produced and tested different types of electrodes, and operated the modules for an extended period of time. Measurement data of solar beam in ultraviolet, visible and near infrared zones were processed statistically, whereas the research work has been completed in the current fiscal year, having established successfully the reference solar radiation. In the hydrogen manufacturing technology using high-temperature direct pyrolysis, fundamental discussions were given on effects of electric and magnetic fields on dissociation of steam, and diffusion and separation of hydrogen by using permeation membranes. For hydrogen fuel cells, trial fabrication and tests were continued on single cells by using mainly the high frequency sputtering process. Experiments were continued on a solid electrolyte fuel cell system. Researches are under way as comprehensive study on such technological seeds as power generation using ocean temperature difference, and superconduction magnets for energy storage (NEDO)

  1. Fiscal 2000 report on result of R and D on robot system cooperating and coexisting with human beings. Development of energy conservation technology; 2000 nendo ningen kyocho kyozongata robot system kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-06-01

    Introduction of a number of robots and consumption of a large amount of energy are unavoidable if a complicated process operation is to be carried out by robots in an extensive work site. Great energy conservation is contrived by developing robots applicable to manufacturing in performing a variety of operations in place of human beings and thereby reducing the number of robots to work. This paper explains the fiscal 2000 results. For dual-handed cooperative tasks, a function was examined capable of gripping an object without giving a humanoid robot an instruction of an exact gripping position. A method was designed to prepare a command for the other arm through a command for one arm, with torque impedance control employed for the purpose of avoiding damage due to collision. A study was conducted on a three-dimensional shape detecting model using a visual device of a robot. In grasping problems of balance control of a humanoid robot, the behavior of a robot consisting of multi-links was considered as behavior of inverted pendulum, with possibility checked for the stabilization of the balance. For the purpose of putting the virtual robot platform previously developed to practical use, a three-dimensional operation tool of run-time user interface was developed, with research conducted on the sophistication of robot application. (NEDO)

  2. Report on the achievements in the Sunshine Project in fiscal 1987. Investigative studies on arranging commercializing conditions for new energy technologies; 1987 nendo shin energy gijutsu no kigyoka joken seibi ni kansuru chosa kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1988-03-01

    The present investigative studies are intended to propose measures of arranging conditions required to commercialize new energy technologies and introduce them into societies. The investigative studies will begin in the current fiscal to put into a complex the new energy industrial plants and the existing different industrial plants. There is a viewpoint that, when structuring specifically a business entity on coal liquefaction processes, some kind of complex is required as seen from the scale and economic performance of the business. Based on this viewpoint, the current fiscal year has carried out the studies placing the importance on technological feasibility for forming a complex with petroleum refining, iron and steel making, chemical and electric power generation industries. The model coal liquefaction plant uses the NEDOL method as the process, and establishes specifications for commercial size plants. The complex formation was discussed with the commercial scale of a coal liquefaction plant assumed to be 30,000 tons per day as the coal treatment quantity and 100,000 barrels per day as the product quantity converted into refined coal liquefied oil. As a result, a conclusion was drawn that, when the complex formation has been done successfully, an attractive business pattern may be formed although some problems may exist. (NEDO)

  3. FY 1998 annual report on the compilation of the data related to new energy technology development. Photovoltaic power generation; 1998 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Taiyoko hatsuden

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The data, centered by those related to generation of photovoltaic (PV) power as one branch of new energy, are collected and systematically compiled under the following fields. (Significance of adopting PV power systems) describes, e.g., CO2 reduction effect and energy pay-back time for different customers, i.e., nation, local governments, industries and individual households. (Present status of solar cell markets) describes solar cell production by region, cell technology and industry; shipments by application; production values; and prices. (PV system policies overseas) compares the policies of the industrialized countries for PV power systems with those of Japan. (Introduction of PV power systems overseas) compares situations of various countries in PV power system introduction with those of Japan with respect to estimated quantities of PV systems installed and target quantities. (Financial supports for PV power system installation) describes subsidies, tax benefits and loans adopted in Japan. Other items covered herein include transition of PV-related budgets, flow of PV system introduction, measures taken by central and local governments, and contacts for PV-related enterprises. (NEDO)

  4. Report on the joint research on the technology development of energy use reduction gas diffusion electrode salt electrolysis; Kyodo kenkyu energy shiyo gorika gas kakusan denkyoku shokuen denkai gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of energy conservation in the 'soda industry' which is an energy multi-consumption industry, study was made of the commercialization applying 'gas diffusion electrode' which is used for fuel cells, and the FY 2000 results were summed up. As to the development of production technology of gas diffusion electrode, conditional studies were conducted of the material production process, grinding process, mixing machine, filling, coating process, hot press process, etc. Concerning the evaluation of durability of the gas diffusion electrode, analysis of long-term operation electrode was conducted, and a lot of information on the degradation mechanism was obtained. In the degraded electrode, wetting of gas diffusion layer is going on, which is thought to directly cause the degradation. It is supposed that between the stable electrode and the degraded electrode, there are no changes in diameter of carbon powder and there is no carbon consumption. As to the verification test using the practical scale electrolytic cell, a trial operation started in February 2001. About the electrolytic performance, the electrolytic voltage is appropriately 2.2V, keeping the stable numerical value. The comparatively favorable performance is being maintained. (NEDO)

  5. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 2. Research study on promotion of international cooperation; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 2. Kokusai kyoryoku suishin no tame no chosa kento

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes the research result on promotion of international cooperation in the WE-NET project in fiscal 1996. The WE-NET project aims at development of the total system for hydrogen production, transport, storage and utilization, and construction of the earth-friendly innovative global clean energy network integrating elemental technologies. Since the standpoint is different between latent resource supplying countries and technology supplying countries, the WE-NET project should be constantly promoted under international understanding and cooperation. The committee distributed the annual summary report prepared by NEDO to overseas organizations, and made positive PR activities in the 11th World Conference and others. The committee made the evaluation on the improvement effect of air pollution by introducing a hydrogen vehicle in combination with Stanford University, and preparation of PR video tapes for hydrogen energy. Preliminary arrangement of Internet home pages, establishment of a long-term vision for international cooperation, and proposal toward the practical WE-NET are also made. 9 figs., 13 tabs.

  6. FY 2000 report on the survey on energy conservation technology of large plant using ultra high corrosion resistant materials; 2000 nendo chokotaishokusei zairyo wo mochiita ogata plant no sho energy gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of achieving remarkable energy conservation/resource conservation in large plants, the paper carried out an investigational survey of effects obtained in case of applying amorphous super metal which is the newest corrosion resistant material. Amorphous alloys as an ultra high corrosion resistant material are a peculiar material which shows the extremely excellent corrosion resistance even in much strong acid by containing passivated elements with the needed concentration. The corrosion resistant amorphous alloy applied to large plants need the thickness and diameter of more than several millimeters as a bulk material. The subjects are scaling-up of bulk materials and stabilization of characteristics. Even under the tough dew point corrosion environment of the waste power plant, etc., heat recovery from exhaust gas is made possible by heat exchanger applied with ultra high corrosion resistant materials. Effects of the annual heat recovery from the nationwide refuse incinerators and coal thermal power plants are estimated to be approximately 5.2 million kL toe, that is, to be equal to energy conservation of 6 x a million kW class power plant. (NEDO)

  7. Fiscal 1999 research report. Data collection for development of new energy technology (Photovoltaic power generation); 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa (taiyoko hatsuden) hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As a part of systematic data preparations on new energy technology, this research aims at collection and analysis of data on domestic and overseas applications, diffusion targets, concrete examples, policies, laws, subsidy systems, and the latest technology development trends of photovoltaic power generation, and at preparation of its basic data through integration and systematization of the collected data. The research items are as follows: domestic and overseas applications, diffusion targets, concrete examples, policies, laws, subsidy systems, productions of solar cells, typical photovoltaic power generation costs, trial calculations of CO{sub 2} reduction in photovoltaic power generation, technology development trends, technology development issues, issues for faster diffusion, configurations and conceptual charts of photovoltaic power systems, and major domestic and overseas trends. As a supplement, domestic and overseas manufacturers of solar cells, and manufacturers of photovoltaic power systems are listed with their addresses. The solar cell production capacities of major countries are also arranged. (NEDO)

  8. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

  9. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation (Hydrogen energy technology standardization); 2000 nendo suiro riyo kokusai clean energy sytem gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. 3. Kokusai kyoryoku ni kansuru chosa kenkyu (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Efforts were made to establish standards necessary to promote the research and development of hydrogen energy technology and the practical application and popularization of the technology. In the study of the base of hydrogen energy technology standardization, research was conducted about Japan's difference from other countries and tasks to discharge and problems to solve in this country, relative to laws and regulations governing the construction of 'hydrogen supply stations' constituting the core of studies in the above-mentioned phase II research and development efforts. Studies conducted toward diffusion into the general public included rules and regulations over the size of hydrogen storage and the distance between dangerous matters and fire. ISO/TC197 (hydrogen technology) was established with the aim of achieving standardization of the system and equipment pertaining to the production, storage, transportation, measurement, and utilization of hydrogen for energy purposes. In fiscal 2000, Working Group 1 registered an 'interface for automated liquid hydrogen fuel delivery system' and 'hydrogen product specifications.' Moreover, Working Groups 2 through 7 were also engaged in their activities, respectively. (NEDO)

  10. Report on the survey in fiscal 1998. A survey on long-term energy technology strategy (a survey related to arrangement of information groups and aiding means for establishing policies related to research and development of energy and environment technologies); 1998 nendo choki energy gijutsu senryaku chosa. Energy kankyo gijutsu kenkyu kaihatsu ni kakawaru seisaku kettei no tame no johogun no seibi narabi ni shien shuho ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This paper discusses aiding means for establishing the research and development strategy for maximizing greenhouse effect gas reduction for a short period (year 2010) and an ultra long period (year 2030 and on). First, the situation surrounding the existing energy and environment technologies and technological assignments (themes) were put into order. Rough calculations were made on the selected themes as to their effect of greenhouse effect gas reduction. Based on the result of these reduction amount calculations, provisionary introduction scenarios including analyses by groups and users were prepared according to each theme. On the other hand, data groups related to the energy and environment technologies were investigated and put into order. The data groups include literatures and achievements of the past researches, and are expected of utilization for estimating the introduction potential to calculate effects of future research and development. In addition, discussions were given on methods to analyze cost-effect relationship in the energy and environment technologies. Importance was placed on the case surveys inside and outside the country, and simple models suitable for themes in the New Sunshine Project were built for an attempt of case studies. (NEDO)

  11. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the superconducting material and device (technical development of the Josephson device hybrid system); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (Josephson soshi hybrid system no gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to establish basic technology for hybrid systems of superconducting and semiconducting devices, study was made on ultrahigh speed and low energy consumption properties of Josephson devices. As Josephson IC technology, a logical circuit, ring network, memory circuit, and oxide superconductor logical circuit were studied. As superconducting hybrid system technology, a Josephson device- semiconductor device interface, formation technology of signal transmission lines, and Josephson-MOS IC technology were developed. In fiscal 1997, as Josephson IC technology, switch motion of 4GHz in clock frequency was achieved by new high-density wiring process. Integration of some semiconducting processor elements, junction of surface- stabilized superconducting thin films, and motion of combination structure of some SQUIDs were also confirmed. On the hybrid system, voltage conversion operation of all interfaces was confirmed. Proper logical operation of the Josephson device hybrid circuit was also confirmed. 95 refs., 90 figs., 5 tabs.

  12. Survey for making a data book related to the development of new energy technology (the photovoltaic power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (taiyoko hatsuden)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A data book related to the photovoltaic power generation was made as a part of the systematical preparation of new energy related data. The paper arranged the importance of introducing the photovoltaic power system and the CO2 reduction effect at levels such as the government, local government, industries and individuals which are users. Described were the production quantity by region/type/company, shipment by usage, production amount and prices of solar cells. Arranged was the situation of policies on the photovoltaic power generation in Japan and developed countries. Examples of the introduction in countries including Japan were examined to know the introduction quantity and target. The paper introduced the subsidy system, preferential tax system and loan system for the introduction of the photovoltaic power system in Japan. The flow was summed up from the planning of the system introduction to the installation. The status of handling with the system introduction of government related organs and local governments was stated. The paper showed a list of the companies related to the photovoltaic power system and the references of solar cell makers and solar system installation makers. The development is so quickly made that the renewal every year of the system and the quality enhancement are required. 32 figs., 112 tabs.

  13. FY 1998 result report. Research/development on the energy overall development/utilization technology of gas hydrate resource; 1998 nendo seika hokokusho. Gas haidoreto shigen no energy sogo kaihatsu riyo gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This study is aimed at studying for survey of gas hydrate (GH) deposit required for GH resource development and gathering of it, and further at studying for industrial utilization technology development of GH which is different in formation condition depending on kind of gas with which it reacts. The results of FY 1998 are as follows. In the study of the situation of existence of gas hydrate in the tundra, the sedimentary environment of the tundra where natural gas hydrate exists was simulated in laboratory to measure thermal conductivity of the sediments including GH. In this fiscal year, design/fabrication/calibration were conducted of the GH synthesizer and thermal analyzer. In the study of GH gathering technology in the tundra, a technology is discussed for recovering gas from GH layer and at the same time substituting CO2 hydrate for GH by blowing CO2 into the geologic layer. In FY 1998, formation/dissociation behaviors were first studied of methane/CO2 mixture hydrate. For the overall energy development of GH resource and promotion of R and D of the utilization technology, studies were made on physical properties of GH and development of the usage. (NEDO)

  14. FY 1999 report on the results of the R and D of the plant use energy utilization rationalization industrial material production technology; 1999 nendo shokubutsu riyo energy shiyo gorika kogyo genryo seisan gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of using plants to the process to produce energy conservation type/environmentally friendly type industrial materials, the R and D were conducted on the improvement in material productivity/stress resistance of plants by transgenetic technology, etc., and the FY 1999 results were summarized. In the study of the creation of plants to produce industrial materials by genetic recombination of eucalyptus trees, it was found out that early maturing branches of eucalyptus trees were a material suitable for Agrobacterium infection, and conditions to efficiently acquire transformation calluses were obtained. In the R and D of the creation of soybeans to produce polyunsaturated fatty acid, a gene of unsaturated enzyme was acquired from Mortierella alpina storing ultra-long chain polyunsaturated fatty acid, and an experimental study was made to study whether or not this gene functions by plant. Further, studies were conducted on the technology to produce hybrid fiber by salt tolerance plants, creation of plants to produce isoprenoid/natural rubber, technology to produce tissue-specific high proteins, study on the molecular breeding of disease resistant plants, etc. (NEDO)

  15. Survey for making a data book related to the development of new energy technology. Fuel cell; 1999 nendo shin energy gijutsu kaihatsu kankei data shu sakusei chosa hokokusho. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    To proceed with the systematical arrangement of the new energy related data, this survey collected the data relating to fuel cells, and systematized them with the aim of making a data book related to fuel cells. Further, fuel cells are still developing, and therefore, the trend of development in this one year was roughly seen to make it the data toward the future development. This data book is composed of Part 1 (the world development trend in FY 1999) and Part 2 (data book). Part 1 was divided into the fixed power system (Chapter 1), fuel cell vehicle (Chapter 2), and selection of fuel (Chapter 3). The book has a big feature that the selection of fuel was added as an individual chapter, which is a difference from that of FY 1998. In the description of the developmental trend of fuel cell vehicle (FCV) in Chapter 2, the results of the present development and the trend were described in line with the subjects in achieving the commercialization of FCV. Part 2 is a data book which indicates the state of technology development of each of various fuel cells such as actual results of the demonstrative operation of fuel cells in Japan and abroad. (NEDO)

  16. FY 1986 Report on research and development of super heat pump energy accumulation system. Part 2. Development of elementary techniques; 1986 nendo super heat pump energy shuseki system no kenkyu kaihatsu seika hokokusho. 2. Yoso gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-04-01

    Summarized in detail herein are R and D results of the chemical heat storage techniques and plant simulation, for R and D of the super heat pump energy accumulation system. For R and D of the chemical heat storage techniques, the R and D efforts are directed to the researches on the fundamental reactions and continuous exothermic reactions involved for the high temperature heat storage type (utilizing the metathesis reactions); researches on the physical properties, heat storage systems, solid-phase reactions, liquid-phase reactors, corrosion of the materials, and so on for the high temperature heat storage type (utilizing ammonia complex); collection of the data related to media and structural materials, tests of the elementary equipment for the absorption and hydration reactions, and so on for the high temperature heat storage type (chemical heat storage utilizing hydration); researches on the media properties and system performance, tests of equipment, and so on for the high temperature heat storage type (heat storage/heating utilizing solvation); researches on the heat storage media, heat storage techniques, corrosion of the materials, systems, and so on for the low temperature heat storage type (utilizing the hydration reactions by mixing solutes); and researches on the media, corrosion and elementary equipment, optimization of the system, and so on for the low temperature heat storage type (clathrate low temperature heat storage systems). (NEDO)

  17. FY 1997 Report on New Sunshine Project. International co-operative projects (Australia-Japan solar energy technology cooperation, etc); 1997 nendo kokusai kyoryoku jigyo. Nichigonado taiyo energy gijutsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Described herein are the progresses, memorandum concluded for the new project, NEDO/MUERI project activities, among others, for, e.g., Australia-Japan solar energy technology co-operative project. The photovoltaic cell outdoor exposure test project has been progressing as expected in Australia since FY 1996. The test data have been collected for one year and analyzed successively. The second information exchange workshop is scheduled in June 1998 in Sydney for the thin-film, polycrystalline photovoltaic cell manufacturing technologies. The new type photovoltaic cell long-term exposure test project has been started in FY 1997 as the new project in Oman. The weather conditions of the test site are very severe, very high both in temperature and humidity. The new type photovoltaic cell modules, centered by the amorphous silicon, will be exposure-tested in the severe atmospheres, to verify long-term reliability of the photovoltaic cells. A total of 5 types of the modules are to be exposure-tested; 3 types of 6 amorphous silicon cells, one type of 2 CdS/CdTe cells, and one type of 2 thin-film polycrystalline cells. (NEDO)

  18. Fiscal 2000 achievement report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; 2000 nendo hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The research aims to develop materials and apparatuses for the purification of atmosphere using titanium dioxide that exhibits a powerful oxidizing capability when irradiated with light. A study is conducted to find out an optimum composition for a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is found to show high denitration efficiency, and this achieves the denitration efficiency goal. As for sheet thickness, 0.75mm is found to be enough. The sheet experiences some hardening in an accelerated exposure test, but does not change much in a surface gloss test or a chalking test. Although a slight reduction is observed in denitration efficiency, yet the durability goal is achieved. In the effort to develop an energy conservation type air cleaning apparatus, field tests and experiments are repeatedly conducted. As for photodenitration in the cleaning apparatus, the number of photodenitration stages and the magnitude of equimolar adsorption area necessary for achieving an 80% denitration rate is calculated from the relations of the NOx concentration profile and the denitration rate in the equimolar adsorption module to (gas flow rate/module surface), and the result shows that the initially intended goal is achieved. (NEDO)

  19. Promotion of the formation of environmentally friendly energy community (FY 2000). Demonstration of the gas turbine repowering waste combined power generation technology; 2000 nendo kankyo chowagata energy community keisei sokushin seika hokokusho. Gas turbine repowering haikibutsu fukugo hatsuden gijutsu jissho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Demonstrative operation was conducted of the super waste power generation system in which the low temperature steam generated in waste incinerator is raised in temperature using the combustion exhaust gas emitted after the power generation using another gas turbine for conducting the steam turbine power generation with high efficiency. The FY 2000 results were summed up. In the demonstrative operation, operation and data acquisition/analysis were conducted following the previous fiscal year by 25MW class gas turbine repowering waste combined power generation facilities (Takahama power plant). Further, four years after the start of operation, the secular variation was studied by disassembly/inspection of equipment. As a result of the operation, the thermal efficiency was approximately 35%, much higher than the existing waste power generation. It was verified that the power system was maintained by the same maintenance as that of the ordinary power system. Moreover, the important point of this system is that no special corrosion resistant materials are used and that the high-efficiency waste power generation was demonstrated by combining the existing equipment. It can be said that the super waste power system has high qualities for forming energy community as a regionally dispersed stabilized power source. (NEDO)

  20. FY 1986 Report on research and development of super heat pump energy accumulation system. Part 1. Development of elementary techniques; 1986 nendo super heat pump energy shuseki system no kenkyu kaihatsu seika hokokusho. 1. Yoso gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1987-04-01

    Summarized in detail herein are R and D results of the super high performance heat pumps and elementary equipment and working fluids, for R and D of the super heat pump energy accumulation system. For R and D of the super high performance compression heat pumps, the R and D efforts are directed to development of new working fluids, high-performance heat exchangers, closed motors and so on for the highly efficient type (for heating only); to researches on mixed coolants, high-efficiency screw compressors and so on for the highly efficient type (for cooling and heating); to development of tooth shape of the screw compression section, surveys on thermal stability of the working fluids for heating and so on for the high temperature type (utilizing low temperature heat source); and to R and D of the high-speed reciprocating compressors and steam superchargers for the high temperature type (utilizing high temperature heat source). For R and D of the elementary equipment and working fluids, researches are conducted on evaporators for mixed working fluids, condensers utilizing the EHD effect, stainless steel plate fin type heat exchangers, heat exchangers for the chemical heat accumulation unit, and so on. The R and D efforts are also directed to the working fluids (alcohol-based and nonalcohol-based). (NEDO)

  1. Fiscal 1997 survey report. Subtask 2 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (survey/study for the promotion of international cooperation; survey/study on the standardization for hydrogen energy technology); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 2 kokusai kyoryoku suishin no tame no chosa kento (suiso energy gijutsu hyojunka ni kansuru chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In relation to the basic study of the standardization for hydrogen energy technology and ISO/TC197, the results of the fiscal 1997 survey were summarized. From fiscal 1994 through 1996, in the wide-range field related to hydrogen energy technology, the survey of the present situation of the related standards/laws was made and the needs/subjects of standardization to be studied in the future were extracted. At the present stage, however, it is still early to enter into the stage of discussing the standardization. Therefore, in this fiscal year, only in the field of the storage/transportation/handling of liquid hydrogen, standards/laws abroad and in Japan were comparatively investigated for the basic study toward the standardization. Further, concerning ISO/TC197, studies were proceeded with of the liquid hydrogen land vehicle fueling system interface/fuel tanks/transportation containers/hydrogen fuel product specifications/airport hydrogen fueling facilities. Some are at the stage of drafting the international standard. Three drafts for the new standard were added such as gaseous hydrogen/hydrogen blend vehicular fuel systems, gaseous hydrogen fuel tanks, and basic requirements for safety of hydrogen systems. The standardization is indispensable to introducing the developed technology to the commercialization. 9 refs., 5 figs., 13 tabs.

  2. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  3. Survey report for fiscal 1998. Surveys on possibility of introducing element technologies and future technological trends in the ECO and ENERGY city projects; 1998 nendo chosa hokokusho. Ekoene toshi project ni okeru yoso gijutsu donyu kanosei to kongo no gijutsu doko ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Covering ECO and ENERGY projects currently on the way under the New Sunshine Project, discussions were given on the possibility of utilizing the technological achievements, and the technological problems therein, from the energy supply and utilization aspects. Taken up as the basic concept of the ECO and ENERGY projects is 'optimization and implementation of a cascade-type energy system in cities under environmental restrictions'. Targets were placed on optimization of a total system including the demand side (a topping system), optimization of a total system including secondary energy other than heat (electric power and gas for example), optimization of energy efficiency for the system as a whole, and minimization of environmental load. The ECO and ENERGY technologies that are assumed for the future application were classified into the following six fields: the optimal energy supply system development field, heat storing technology field, thermoelectric power generation field, environment friendly heat pump system technology field, waste heat utilizing heat cycle technology field, and LNG cold heat utilizing technology field. (NEDO)

  4. Research and development of utilization technology of solar thermal system for industrial and other use. Research and development of solar system (research for solar/energy-conservation technology retrofitted to existing buildings); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Solar system no chosa kenkyu (solar toshi muke gijutsu ni kansuru chosa)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for solar/energy-conversion technologies retrofitted to existing buildings. The estimated effects and economic viability of retrofitting technologies show that they bring very high energy-saving effects when applied to heating and hot water supply, which consume a large portion of energy, but relatively low energy-saving effects when applied to cooling, solar walls, glazed balconies and transparent insulators. The study on applicability of these technologies in Japan indicates that the technologies which can recover cost within an average life time are those applied to windows, solar collector systems for hot water supply and heating, and transparent insulators. Although these technologies are low in applicability to cooling viewed from the angle of cost recovery, retrofitted radiation type cooling systems improve not only cooling and energy-saving effects but also comfortableness.

  5. Evaluation report on the development of energy conservation/environment purification system using cleaning effect of optical irradiation; Hikari clean gijutsu wo mochiita sho energy kankyo joka system no kaihatsu hyoka hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The results achieved in fiscal 1992-1995 under the above-named project are stated. In the development of photocatalytic materials, a photocatalytic fluorocarbon polymer sheet suitable for use in a denitration apparatus is developed. A high density fluorocarbon polymer sheet composed of TiO{sub 2} modified with 0.3% of Pd/absorbent zeolite/fluorocarbon polymer PTFE (polytetrafluoroethylene) =48-63/24-36/10-20 is fabricated, which achieves a level higher than the denitration goal of 70%. Although the sheet in a 500-hour accelerated exposure test undergoes a hardening phenomenon in which elasticity decreases and tensile strength increases, yet degradation is hardly detected. Although a slight reduction is detected in denitration efficiency, yet it does not affect its practical application, and thus the durability goal is achieved. In the development of an energy conservation type air cleaning apparatus usable in underground parking areas or motorway tunnels, an apparatus capable of treating air at a rate of 2,000m{sup 3}/hour is fabricated, and this achieves a denitration level of not less than 80% in a field test (in the absence of rainfall). For denitration in the presence of rainfall, the apparatus is combined with an equimolar adsorption system, and a system capable of 80% denitration is proposed on the basis of data actually measured for each of the two. A conceptual design for a service model comprising a photodenitration and equimolar adsorption systems is evaluated, and it is found that it occupies less space than the existing models. (NEDO)

  6. Fiscal 1996 report on the results of the study under a consignment from NEDO of environmental friendly type metal base-materials recycling utilization basic technology and element/overall process. For public; 1996 nendo chikyu kankyo sangyo gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko kyodo kenkyu itaku. Kankyo chowagata kinzokukei sozai kaisei riyo kiban gijutsu no kenkyu: yoso sogo process kenkyu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A study of `the next generation new iron steel making process` was conducted in which impurity elements in scrap are removed and recycled into high quality steel making materials, and at the same time total emissions are reduced during the process from scrap melting to steel making. The paper reported the fiscal 1996 results. In the study of the scrap recycling process, conducted were a study of the total system to remove impurities in the high temperature preheating furnace, a large scale experiment of de-coaling combined type de-coppering/de-tinning under reduced pressure of iron melting, a study of recycling technology of dust to the scrap melting furnace, etc. In the study on preheating/melting technology, a study of the scrap melting furnace of high-productivity/low-energy vertical type, a study of the scrap preheating method using the packed bed type preheating furnace, a study on the flue gas control at the time of preheating/melting, a study of the fast assessment method for organic compounds in flue gas, etc. In the evaluation of the total system, a study of preheating/melting/environmental systems using experimental plants. 20 refs., 23 figs., 10 tabs.

  7. Achievement report on research and development in the Sunshine Project in fiscal 1977. Studies on hydrogen energy total systems and the safety assuring technologies thereon (Studies on preparing criteria for the safety assuring technologies for hydrogen energy total systems); 1977 nendo suiso energy total system to sono hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso energy total system no hoan gijutsu kijun no sakusei ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-01

    Studies have been made on preparing criteria for the safety assuring technologies for hydrogen energy total systems. The outline of the technological guideline for hydrogen manufacturing processes in the high temperature and pressure water decomposition method is the same as that in the normal pressure water decomposition method. However, its high temperature and pressure environment can cause new safety problems. Considerations should be given on, for example, material problems in structural materials and insulation materials including electrodes and membranes, introduction of gas-liquid separation and pressure balancing devices, problems in electrolyte circulation, and safety problems that may occur because of generation of hydrogen and oxygen under high temperature and pressure conditions. This paper summarizes these matters by surveying literature data. In order to provide basic information to prepare criteria for safety assuring technologies for the gaseous hydrogen liquefaction process, surveys and studies were made based on different items of technological information and experimental study results. Safety assuring technologies were discussed on metal hydrides (promising means for storing hydrogen). Powder is used to enhance hydrogen absorbing performance, whereas the metal hydrides are pulverized as a result of repetition of absorption and discharge of hydrogen. This paper describes also metal dust explosion disaster and its risk of occurrence. (NEDO)

  8. Fiscal 2000 survey report on rationalization project for international energy conservation, technological dissemination project for international energy conservation, and Green Helmet Project. Japan-China alternative energy seminar/waste disposal; 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo, kokusai energy shohi koritsuka nado gijutsu fukyu jigyo, green helmet jigyo chosa hokokusho. Nicchu sekiyu daitai energy seminar haikibutsu shori

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper explains the Japan-China alternative energy seminar (February 28 and March 1, 2001, at Beijing). The purpose of the seminar is to introduce systematic and three-dimensional or land/sea/air measures for waste disposal including recycling in Japan, to provide guidance of measures in improving recognition and methods for waste disposal in China, and also to contribute to the dissemination and promotion of a model project for effectively utilizing waste heat from rubbish incineration, a project being implemented in Harbin City now. The activities of NEDO were introduced, with emphasis placed on a model program, called Green Aid Project, for managing heat from waste incineration. On the subjects of sustainable development, urban environment, and energy, the policy of China's tenth five-year plan was demonstrated, and the treatment of wastes in China was also explained. The present state of waste processing in Japan was introduced, as was its maintenance of the facilities. Concerning Japan's waste processing technologies and characteristics of the equipment, there were presented non-incineration processing including crushing/separating, RDF, compost, methane fermentation, etc.; incineration plants; and each of the technologies such as combustion, exhaust gas, ash treatment, use of remaining heat, and gasification melting. (NEDO)

  9. Achievement report for fiscal 1998 on development of wide-area energy utilization network system. Study of energy system designing technology (Research into factory area energy system); Koiki energy riyo network system kaihatsu, energy system sekkei gijutsu no kenkyu 1998 nendo seika hokokusho. Kojogun no energy system ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Actualities of exhaust heat and demand for heat in the area are investigated on the result of which a wide-area energy utilization network system will be built. In fiscal 1998, further questionnaires are distributed in addition to last fiscal year's, and door-to-door visits are made on leading factories representing 10 types of industries. The result of data analysis places the nationwide total of exhaust heat at 320,000 Tcal/year including heat generated by electric power generation. When it is so defined that usable heat be above 150 degrees C for exhaust gas, above 40 degrees C for hot water, and above 200 degrees for solids, the total will be reduced to 230,000 Tcal/year. Cleaning plants (plants that treat refuse or sewage) as the sources of exhaust heat besides the factories are investigated for the amount of heat they discharge, and then it is found that the amount of heat they discharge is the fourth largest following electric power plants, iron and steel mills, and chemical plants. It is also found that most of their exhaust heat is of good quality because it is latent in steam or hot water. It is acknowledged, partly because many of such plants are situated relatively near to the urban district, that their role is important when studies are made on the utilization of exhaust heat. (NEDO)

  10. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on peripheral technologies around hydrogen); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso no shuhen gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-01

    This report summarizes the fiscal 1975 research result on peripheral and seed technologies for hydrogen energy systems. Chapter 1 'Evaluation method for thermochemical techniques' reports critical study on qualitative evaluation method, estimation method for thermal efficiencies, and trial cost calculation example. Chapter 2 'Current state and problems of water electrolysis and hybrid technique composed of electrolysis and thermochemical technique' reports general survey on current water electrolysis and new technologies under development to clarify possible electrolytic voltage drop, from the practical viewpoint. Chapter 3 'Use of a high- temperature gas cooling reactor for hydrogen production' reports survey on the current and future reactors, and characteristics of such nuclear reactors, from the viewpoint that study on thermochemical technique is dependent on use of a high-temperature gas cooling reactor. Chapter 4 'Hydrogen transport and storage technology using organic compounds including oxygen' reports that acetone-isopropanol system is better for hydrogen storage. Chapter 5 'Water electrolysis using photo-semiconducting electrode' reports the additional survey. (NEDO)

  11. Fiscal 1997 report on the results of the introductory R and D of the New Sunshine Project under a consignment from NEDO. Introductory R and D of the supercritical fluid use technology; 1997 nendo `New Sunshine keikaku` sendo kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chorinkai ryutai riyo gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The R and D of chemical reaction using supercritical fluids started in fiscal 1997. In the R and D of solvent reaction, as the research on polymer decomposition with supercritical water, studies were conducted of the mechanism of conversion reaction to chemical materials, cleavage mechanism of stable chemical bonds, and synthetic reaction in the supercritical state reaction field. In the research on oxidation reaction, as the study of complete oxidation in supercritical water for high efficiency energy recovery, studies of complete oxidation of liquid fuels, and complete oxidation of solid fuels. In the research on hydrogenation, studies of lightening of heavy oil in supercritical water, etc. In the R and D of the basic technology, studies of corrosion mechanism of metals in supercritical water, construction of the basic framework for technical database of supercritical fluids, etc. In the survey of technical trends and new research themes, the introductory R and D of element technology, etc. were conducted, and the results were described of the survey of technical trends and new research themes and the trend survey of overseas technology. 314 refs., 87 figs., 81 tabs.

  12. Fiscal 2000 international energy use rationalization measures project. International energy consumption efficiency improvement technology diffusion project - Green helmet project (Thailand: Report on heating furnace energy conservation seminar); 2000 nendo. Kokusai energy shiyo gorika to taisaku jigyo, Kokusai energy shohi koritsuka to gijutsu fukyu jigyo, Green helmet jigyo (Thai : kanetsuro shoenergy seminar hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The above-named seminar was held in Bangkok, Thailand, on January 30, 2001, and covered three kinds of industries of ceramics, glass, and aluminum. Approximately 200 people attended the meeting, consisting of NEDO (New Energy and Industrial Technology Development Organization)-affiliated people and 16 lecturers from Japan, and Thai participants. The seminar comprised a 'keynote address' and 'lectures on engineering' that aimed at the three industries as a whole, and 'lectures on engineering' and 'cases and activities for energy conservation' that aimed, respectively, at the three industries. Lectures were delivered on operating technologies which were already in practical use and on state-of-the-art technologies. The keynote address, entitled 'Global warming prevention and industrial furnaces,' covered the results of the 'High-performance industrial furnace field test project.' The lectures on engineering dealt with the 'instrumentation control system' and 'heat insulation technology' which were basic technologies for energy conservation and 'diagnosis technology and practice' which aimed at the enhancement of energy conservation after the start of operation. Questions and answers were earnestly exchanged. (NEDO)

  13. Fiscal 1998 research report on the basic research on the practical application of innovative technologies. 2; 1998 nendo kakushinteki energy gijutsu no jitsuyoka ni kansuru kiso chosa hokokusho. 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report is composed of the part 1 'Estimation of fossil energy resources and preliminary preparation of the super- long-term view of energy supply and demand', and the part 2 'Research on concrete conditions for introducing renewable energy (RES)'. In the part 1, estimation was made on the amount of non-conventional fossil energy resources such as oil sand, oil shale, coal bed methane and methane hydrate. Study was also made on the role of nuclear power, fast breeder reactor and nuclear fusion in the world energy supply and demand in the 21st century. In addition, as preliminary study on the super-long-term view of energy supply and demand in the next fiscal year, study was made on a scenario and measuring model considering energy supply restriction and CO{sub 2} problem. In the part 2, research was made on the amount of resources, applicable fields and cost estimation for various RESs such as solar energy, wind power, biomass, oceanic energy, geothermal energy and hydraulic power. Several technical issues on transport, storage, conversion and use for every energy were arranged toward real introduction, efficient use and stable supply of such RESs. (NEDO)

  14. Fiscal 1997 report on the survey for a data book on new energy technology development. Waste power generation, solar energy utilization. geothermal power generation, clean energy vehicles, coal liquefaction/gasification, and traverse themes; 1997 nendo chosa hokokusho. Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika gas ka oyobi odanteki theme)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper collected and arranged data on new energy technology. As to the waste power generation, in terms of general waste, 161 places have power generation facilities, 657,000 kW in output, as of the end of FY 1996. Out of them, 100 facilities (scale of output: 555,000 kW) are selling power. In terms of industrial waste, 53 places (209,000 kW) have power generation facilities. The output will be 2 million kW in FY 2000. In relation to the solar energy utilization, the number of solar systems introduced in FY 1996 is 25,000, that of water heating appliances produced in FY 1996 is 170,000. Geothermal power of 494,000 kW and 37,000 kW was introduced for electric power industry use and private use, respectively. Clean energy vehicles have not been so much spread, but the hybrid car was put on sale in 1997. Concerning the coal liquefaction, the R and D were made at a pilot plant of NEDOL process, and operation started in 1997. As to the coal gasification, investigational study and element study on the demonstration plant are being conducted in FY 1997 and 1998, making use of the research results obtained from the existing pilot plant of coal gasification combined power generation

  15. FY 2000 survey report on the project for preparation of the international energy utilization rationalization basis. 1st volume. Survey/study for the spread of energy conservation technology; 2000 nendo chosa hokokusho. Kokusai energy shiyo gorika kiban seibi jigyo (Sho energy gijutsu no fukyu no tameno chosa kenkyu to - 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In China which is the largest energy consumption country in the Asian region and has much room for the spread of energy conservation technology, investigational study was made with the aim of widely spreading energy conservation technology and solving environmental problems. To grasp energy supply/demand in China, environmental problems, industrial structure and social system, it is necessary to have process for establishment of data monitoring method, construction of database and model simulation. Proposal for model simulation was made. Further, to make macro-basis assessment of potentiality of energy conservation and environmental effect by sector in China, following the previous fiscal year, study was made on the electric power industry, where there is big potentiality of heightening energy utilization efficiency but the rationalization is not proceeded with. Moreover, in this fiscal year, energy demand is expected to increase with the growing economy, and the traffic field which has a great effect on the environment was added to the investigational research. (NEDO)

  16. Achievement report on research and development in the Sunshine Project in fiscal 1977. Studies on hydrogen energy total systems and the safety assuring technologies thereon (Studies on hydrogen energy total systems); 1977 nendo suiso energy total system to sono hoan gijutsu ni kansuru kenkyu seika hokokusho. Suiso energy total system no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1978-03-01

    A numerical model was prepared to express fields and size of hydrogen energy introduction in Japan's energy systems in the future. Dividing Japan into 13 weather sections, one to two energy bases (import and secondary production bases in coastal areas) were assumed on each section. Secondary energies produced in these energy bases are transported to intermediate bases, from which the energies are distributed into cities and consumed. For the purpose of simplification, final consumption departments are hypothesized to exist in these intermediate bases. Parameters that characterize the flows on networks in the processes of supply, distribution, production, storage, transportation and utilization are divided largely into energy efficiency and cost of the processes. The amount of energy demand in each final consumption department was defined as an amount to maximize the expected effects as a result of having satisfied the demand. The result of trial calculations revealed that, as long as the hydrogen to be introduced is limited to hydrogen produced via electrolysis using thermally generated power, the hydrogen introduction into the future energy systems is difficult in terms of economic performance. (NEDO)

  17. Development of a wide-area energy utilization network system (research on a technology to design an energy system). FY 1998 report on achievements of research on systematizing ECO and ENERGY cities; Koiki energy riyo network system kaihatsu (energy system sekkei gijutsu no kenkyu). 1998 nendo eko ene toshi no system ka kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    As a research on systematizing ECO and ENERGY cities, surveys and analyses were performed on the actual state of introducing district heat supply systems utilizing difference waste heats including factory waste heat. Waste heat from electric power generation is utilized for district heat supply in Japan at 122 points or about 20% of the district heat supply points in operation as of March 1998. The number is in the increasing trend in recent years, and the future potential of its introduction can be said high as the history thereof is still short. Its introduction form is accounted mostly for by building cogeneration or plant cogeneration. Back-up facilities for the case when waste heat supply stops because of regular facility checks are provided by the heat supply business operators, which impede the economy of the system. In the U.S., the Public Utility Regulatory Policy act motivated installation of cogeneration and off-peak power generation systems for district heat supply. Technical maps (for waste heat sources and different waste heat utilization systems) were prepared based on the surveys to discuss the future measures. (NEDO)

  18. FY 2000 report on the results of the advanced R and D for the UTES (underground thermal energy storage) system; 2000 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this study, study was made of the commercialization of the UTES (underground thermal energy storage) system using the underground heat source heat pump system technology as the base, considering that this is a technology suitable for the urban area where the heat demand intensively increases and a lot of exhaust heat and usable heat exist. By the realization of the UTES system technology, it is expected that the system promotes Japan's utilization of the unused energy and contributes to the construction of the CO2 emission control type society for Japan's energy policy and global warming prevention and secondarily to leveling of power loads and elimination of the heat island phenomenon in large cities. As to the UTES system which is aimed at being used for space heating and cooling and hot water supply in buildings, the following two were studied: the indirect system, BTES (borehole thermal energy storage) system, in which heat is collected/radiated from the ground by the heat exchanger installed underground; the direct system, ATES (aquifer thermal energy storage) system, in which the groundwater stored in aquifer is directly pumped up and used. The study was made in the items written below: 1) establishment of an system image of the UTES system; 2) evaluation study of effects of the introduction, practical applicability, etc. 3) extraction of the subjects for development. As a result, system images of the indirect/direct systems were obtained. (NEDO)

  19. FY 2000 report on the results of the advanced R and D for the UTES (underground thermal energy storage) system; 2000 nendo chichu jiban chikunetsu system gijutsu sendo kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this study, study was made of the commercialization of the UTES (underground thermal energy storage) system using the underground heat source heat pump system technology as the base, considering that this is a technology suitable for the urban area where the heat demand intensively increases and a lot of exhaust heat and usable heat exist. By the realization of the UTES system technology, it is expected that the system promotes Japan's utilization of the unused energy and contributes to the construction of the CO2 emission control type society for Japan's energy policy and global warming prevention and secondarily to leveling of power loads and elimination of the heat island phenomenon in large cities. As to the UTES system which is aimed at being used for space heating and cooling and hot water supply in buildings, the following two were studied: the indirect system, BTES (borehole thermal energy storage) system, in which heat is collected/radiated from the ground by the heat exchanger installed underground; the direct system, ATES (aquifer thermal energy storage) system, in which the groundwater stored in aquifer is directly pumped up and used. The study was made in the items written below: 1) establishment of an system image of the UTES system; 2) evaluation study of effects of the introduction, practical applicability, etc. 3) extraction of the subjects for development. As a result, system images of the indirect/direct systems were obtained. (NEDO)

  20. FY 1998 survey report. Feasibility study of the new energy introduction/spread policy application (Study of the model project conception using natural energy utilization technology); 1998 nendo chosa hokokusho. Shin energy donyu fukyu hosaku tekiyo kanosei chosa (shizen energy riyo gijutsu wo katsuyoshita model jigyo koso no kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This survey clarified the problems about that consumers and various kinds of group do not come to tackle independently and positively the use of natural energy and the solutions, and studied the necessity of the model project to enlighten the society on those concretely and widely. The model project conception is to spread/settle various kinds of natural energy by making them linked with the regional economic growth and resource/environment problems in a community with a regional autonomous body as a unit. There, new incentives to be made toward the promotion/spread of natural energy are presented such as the construction of an energy self-supporting society which is closed-cycle by using various kinds of energy combinedly and compositely, the formation of ideas for adding values except kWh value to electric power generated by natural energy, etc. Besides, about the conception of model project, the training facility function and demonstration exhibition function for the purpose of education/enlightenment are also added in consideration of the importance of natural energy that general citizens should feel close to themselves. (NEDO)

  1. Report on achievements in fiscal 1998. Development of technologies to put photovoltaic power generation systems into practical use - Research and development of solar beam power generation and utilization systems and ancillary technologies (Investigations and researches on large-size energy supply system); 1998 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Taiyoko hatsuden riyo system shuhen gijutsu no kenkyu kaihatsu (ogata energy kyokyu system no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With an objective to propose large-size system development scenarios assuming installations in deserts, the following investigations have been carried out: (1) collection of data on societies, economy, and energies in China and other countries where the large systems are assumed to be installed, (2) in order to reduce the costs, comparison was given on power generation cost by using a fixed tracking frame, a single axial tracking frame, and a biaxial tracking frame, (3) in order to evaluate the life cycle, discussions were given on the required energy inputs for system equipment, transmission and transformer equipment, and the installation construction to estimate the energy payback time (EPT) and CO2 emission unit requirement, and (4) discussions on development scenarios. In Item (1), while China expects on natural gas and atomic energy as the supply source, 80% of the energy would be supplied from coal in 2010. The development of new energies in India would further be delayed than in China. In item (2), the trially calculated power generation costs in Mongol by using the fixed frame, single axial tracking frame, and biaxial tracking frame were 8.72, 8.23 and 6.94 yen per watt. In Item (3) The EPT was two years or less in a 100-MW system, and the CO2 emission unit requirements in the silicon systems were 10 to 19 kg-C/kWh. (NEDO)

  2. Achievement report for fiscal 1981 on Sunshine Program-entrusted research and development. Survey and research on patent and information (Survey of new energy technology development information - Hydrogen and other energies); 1981nendo shin energy gijutsu kaihatsu joho chosa seika hokokusho. Suiso sonotano energy hen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Surveys are conducted and the results are reported on the development of technologies in the U.S., Canada, Britain, West Germany, and France, for hydrogen energy, and for wind power, biomass power, marine power, wave power, etc. In the U.S., development funds are being introduced by the Government into wind power systems since 1975, and part of the power is utilized in the fields of agriculture and power supply business. The task is now being transferred from the Government to private sector businesses. Probabilities are that hydrogen will not be an important source of energy in the U.S. In the Province of Ontario, Canada, where there is surplus electricity, people have a great interest in the development of hydrogen energy, and there is a task force to discuss hydrogen energy. As for wind power, it is already in the realm of practical application. In Britain, wind power is expected to come into practical use very early, and the first practical plant will begin its service operation by 1984. As for the study of tidal power, however, it is narrowed down to a project at the mouth of the Severn river. As for hydrogen energy, the research remains at the basic stage, and the energy enjoys but a low precedence. (NEDO)

  3. Feasibility study for international collaboration on photovoltaic power generation and long-distance energy transmission technologies utilizing desert areas environment; Sabaku chiiki wo riyoshita taiyoko hatsuden chokyori yuso gijutsu ni kakawaru kokusai kyoryoku kanosei chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    A workshop was held at Tokyo in March, 1997 on the research and development and feasibility study for international collaboration on photovoltaic (PV) power generation and long-distance energy transmission technologies utilizing desert areas environment. Two speakers from the USA, one from Italy, and two from China were invited, and four speakers in Japan presented papers. A total of 48 persons participated. In the technical sessions, `World energy demand and PV system potential` by Prof. Kurokawa, `Long distance transmission of PV power` by Mr. A. Invenizzi, `Case studies of large scale PV systems distributed throughout desert areas of the world` by Mr. Hirasawa, `Linking renewable energy resources around the world` by Mr. P. Meisen, `Properties of large scale PV plant in the USA` by Mr. J. Benner, `Future prospect of PV electrification in China` by Mr. Kong Li, `Application of large-scale PV systems in deserts in China` by Mr. Isomura, and `Effects of large-scale PV power plant in a climatic desert areas` by Prof. Ihara were presented. 38 refs., 62 figs., 29 tabs.

  4. FY 1998 annual report on the solar energy technology research and development working group. 19th R and D activity report; 1998 nendo taiyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Summarized herein are the FY 1998 R and D activities by the solar energy R and D working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, gave a lecture titled (Expectation on and problems involved in power generation by solar light and wind power), and Mr. Kamon, a managing researcher of NEDO's solar technology development group, reported (Technological development trends of solar technology development group). The other topics reported by the individual groups include development of large-size wind power generation systems, development of techniques for increasing throughputs of high-efficiency, large-area amorphous solar cells, development of techniques for manufacturing high-reliability CdTe solar cell modules, development of techniques for manufacturing CIS solar cell modules, analysis/assessment of thin-film silicon-based solar cells, development of processes for manufacturing silicon of rationalized energy use, R and D of (new multi-layer structure) modules assembled into building materials to form monolithic structures, and development of techniques for manufacturing amorphous thin-film polycrystalline silicon hybrid thin- film solar cells. (NEDO)

  5. FY 1998 annual report on the solar energy technology research and development working group. 19th R and D activity report; 1998 nendo taiyo gijutsu bunkakai. Dai 19 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    Summarized herein are the FY 1998 R and D activities by the solar energy R and D working group, extracted from the 19th R and D activity report by NEDO. Mr. Kadoi, a NEDO's director, gave a lecture titled (Expectation on and problems involved in power generation by solar light and wind power), and Mr. Kamon, a managing researcher of NEDO's solar technology development group, reported (Technological development trends of solar technology development group). The other topics reported by the individual groups include development of large-size wind power generation systems, development of techniques for increasing throughputs of high-efficiency, large-area amorphous solar cells, development of techniques for manufacturing high-reliability CdTe solar cell modules, development of techniques for manufacturing CIS solar cell modules, analysis/assessment of thin-film silicon-based solar cells, development of processes for manufacturing silicon of rationalized energy use, R and D of (new multi-layer structure) modules assembled into building materials to form monolithic structures, and development of techniques for manufacturing amorphous thin-film polycrystalline silicon hybrid thin- film solar cells. (NEDO)

  6. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on hydrogen combustion technology); 1975 nendo suiso nensho gijutsu ni kansuru kenkyu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-01

    This research mainly aims at establishment of various conditions necessary for using hydrogen fuel. The research includes (1) properties of hydrogen-methane mixture gas, and the proposal to future R and D, (2) extraction of various problems in practical use of home or industrial combustors, and evaluation of existing technologies, (3) the environmental impact of hydrogen fuel and its reduction measures, and (4) estimation of energy structures in cities and placing of hydrogen fuel in 2000. Detailed study items are as follows. In (1), general and proper combustion characteristics of and combustion technology for hydrogen- methane mixture system. In (2), problems for every use of various gas equipment, application of various gas equipment to hydrogen, peripheral technologies, conversion from natural gas, problems of heating furnaces and hydrogen burners, combustion safety/control equipment for various combustors, water content recovery combustion system, hydrogen embrittlement, and sealing. In (3), NO{sub x} generation in hydrogen combustion and its reduction measures. In (4), problems in introduction of a hydrogen-electric power energy system to an assumed model city in 2000. (NEDO)

  7. FY 2000 survey report on the project for preparation of the international energy utilization rationalization basis. 2nd volume. Survey/study for the spread of energy conservation technology; 2000 nendo chosa hokokusho. Kokusai energy shiyo gorika kiban seibi jigyo (Sho energy gijutsu no fukyu no tameno chosa kenkyu to - 2)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In China which is the largest energy consumption country in the Asian region and has much room for the spread of energy conservation technology, investigational study was made with the aim of widely spreading energy conservation technology and solving environmental problems. This report summed up the tackling with environmental problems for making improvement in energy conservation. In the study of the CDM introduction based on the heat supply in Beijing city, conducted were the report on the research on the CDM introduction to coal-fired heat supply facilities and small gas boilers and the consideration of possibility/conditions/method of Japan's transfer of technically advanced space heating technology to China. In the study of 'advanced traffic system - Tsinghua University Green Campus Project,' carried out were the simulative study for grasp of the traffic flow in university, consideration of characteristics of exhaust gas at the time of car running on road and the road pollution mechanism, consideration of the study of electric cars considered of the environment. (NEDO)

  8. Survey report in fiscal 1999 on investigations for the current status in energy and environmental problems in Japan and the U.S.A., and investigations on technological development related to energies; 1999 nendo Nichibei ni okeru energy kankyo mondai no genjo chosa oyobi energy ni kakawaru gijutsu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper reports the surveys in fiscal 1999 on energy and developmental problems in Japan and the U.S.A. New and complex environmental problems are rising to the surface, such as global warming, ozone layer destruction, and chemical harms. It is necessary to deepen quickly scientific understanding of the problems, and identify accurately their impacts on human bodies and ecological systems. Within the limitation of the scientific understanding, political decisions on economy and environmental risks are also important and difficult questions, with the environmental hormones being the typical examples. Establishing chemical substance verification systems is important, whereas joint researches by Japan and the U.S.A. are desired. Policy decisions on handling the researches must also be made jointly, and acceptance by citizens must be asked for at international workshops. While energies are the base of economic activities, and the sustained development thereof is indispensable, how to take balance with health and environment in the global scale is a large assignment. Joint Japan-U.S. discussions are required on technological innovation, such as for regenerative energies, energy conservation, safety of and wastes from nuclear reactors, clean use of fossil fuels, and fuel cells. International cooperation, including that from developing countries, is also important. (NEDO)

  9. Report on the results of the FY 1999 introductory R and D of MGC ultra-high efficiency turbine system technology. International cooperative project of MGC technology investigational study (R and D on advanced engine and energy saving use ceramics); 1999 nendo MGC chokokoritsu turbine system gijutsu sendo kenkyu kaihatsu seika hokokusho. MGC gijutsu chosa kenkyu kokusai kyoryoku jigyo (senshinteki engine oyobi sho energy yo yotoyo ceramics ni kansuru kenkyu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    As the R and D of advanced engine and energy saving use ceramics, this project is being conducted by the U.S., Germany, Sweden, Belgium and Japan under Annex II of the Committee of Energy Research Technology (CERT) established by International Energy Agency (IEA). For structure use ceramic materials, their raw material powder is tested and a method to evaluate characteristics of their sintered bodies is studied. The research was divided into Subtask 11 (test on mechanical characteristics) and Subtask 12 (evaluation of raw material powder). Each subtask decides on the details of the international joint research and the associated research assigned to each country. In the testing study on mechanical characteristics in this fiscal year, the evaluation method was studied of thermal characteristics of materials for heat resistant high temperature members. In the study for evaluation of raw material powder in this fiscal year, a method was studied for evaluation of characteristics of fine ceramic powder. The results to be obtained in this study are related to mechanical characteristics of materials for heat resistant high temperature members and to the basic evaluation method of characteristics of raw material powder. The results of the study are surely indispensable for promotion of the application of these materials. (NEDO)

  10. Report on the development of the environmentally friendly type high efficiency energy utilization system - Study of the optimum system design technology. Case study of the wide area energy supply network in the Osaka prefectural region; Kankyo chowagata kokoritsu energy riyo system kaihatsu - saiteki system sekkei gijutsu no kenkyu hokokusho. Osakafuiki ni okeru koiki energy kyokyu network no case study

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The paper worked out a model of the wide area supply network which combines the element technology being developed in the eco/energy urban project and the existing technology to apply it to the actually existing city, and the evaluation study was made of energy conservation effects, environmental preservation effects, economical efficiency, etc. The FY 2000 results were reported. In this fiscal year, a case was studied of using the exhaust heat from waste incineration plant by wide area network in the region having a plan of redevelopment/rezoning of the city of Osaka where heat is in great demand. The results of the study were as follows: The total primary energy consumption amount is reduced by 16.3-19.7% in the conventional heat insulation pipe method and by 19.2-20.6% in the vacuum heat insulation method. As to the environmental preservation, the CO2 reduction amount is 36.9-40.0%, and the NOx reduction amount is 43.7-45.5%, which indicated much more improvement than in the present situation. In the aspect of economical efficiency, the result indicated that in the case of the shortest piping, much economical efficiency is expected even without subsidies if considered of the carbon tax. (NEDO)

  11. FY 2000 International energy use rationalization project. International technology dissemination project for improving energy consumption efficiency (Green helmet project for steel heating furnaces in Thailand); 2000 nendo kokusai energy shiyo gorika nado taisaku jigyo chosa hokokusho. Kokusai energy shohi koritsuka nado gijutsu fukyu jigyo (Green helmet jigyo (Tai: kozai kanetsuro))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The project for energy saving dissemination activities and technological assistance for Thailand is carried out, and the FY 2000 results are reported. For Siam Iron and Steel (SISCO), the experts are dispatched for reviewing the operating conditions of the facilities constructed by the model project, their maintenance and examination, time series diagnosis of the recuperator performance, and providing technical assistance for fuel consumption and high-load combustion of the downstream unit. Furthermore, the site survey and technical assistance are provided for two newly selected Thai steel enterprises, Sahaviriya Steel Industries Public Co. (SSI) and the Bangkok Iron and Steel Works Co. (BISW). For SSI, it is predicted that energy of approximately 50Mcal/ton can be saved by, e.g., enhancement of waste heat recovery, enhancement of heat insulation of skid pipes, introduction of steel discharging temperature prediction system, and combustion control. For BISW, it is predicted that energy of approximately 25Mcal/ton can be saved by, e.g., enhancement of waste heat recovery and reduction of heat loss in the waste gas. (NEDO)

  12. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  13. Fiscal 1980 Sunshine Project research report. International cooperation project for energy technology. International research cooperation for geothermal energy (Japan-U.S. R and D cooperation for geothermal resource assessment); 1980 nendo energy gijutsu kokusai kyoryoku jigyo chinetsu energy kokusai kyoryoku seika hokokusho. Chinetsu shigen hyoka ni kansuru Nichibei kenkyu kaihatsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    Based on the Japan-U.S. agreement on promotion of geothermal energy applications, the R and D cooperation specialist panel was held in America on March 12-20, 1981 to exchange the current R and D information on geothermal resources. It was clarified through the meeting in Department of Energy (DOE) that the U.S. budget was reduced by the Reagan Administration largely, resulting in delays in development of geothermal energy and construction of geothermal power plants. The following themes were discussed: Japanese and American geothermal development programs, DOE's industrialization activity, hot dry rock program, geoscience program, and geothermal prospecting technology program. It was clarified through the meeting in U.S. Geological Survey (USGS) that since the governmental resource assessment is made by USGS, however, wide data collection is made by other organizations generally, acquisition of data required for the assessment is difficult. Study on MOU is necessary together with fund allocation. Field survey was also made in Raft River, Cove Fort and Roosevelt. (NEDO)

  14. Power load leveling and energy saving measures for office buildings. Power load leveling and energy saving technology for the new building of the Kobe branch of the Kansai Electric Power Co., and its effect; Office biru no denryoku fuka heijunka sho energy hosaku. Kobe shiten shinshaoku ni okeru denryoku fuka heijunka sho energy gijutsu to sono koka

    Energy Technology Data Exchange (ETDEWEB)

    Tsuchiyama, M. [Kansai Electric Power Co. Inc., Osaka (Japan)

    1999-06-10

    This paper presents power load leveling and energy saving measures for heat source, air conditioning and lighting of the new Kobe branch building. The low-temperature hot-air system adopts an ice storage system, and reduces blowing power by 12 degreesC blowing in place of normal 16 degreesC blowing, and an initial cost by duct size reduction. The continuous air conditioning system levels an initial peak load of air conditioning as compared with normal air conditioning only for working hours for buildings with large heat capacity. In addition, as power load leveling measures for the whole building, the complete heat storage system using an underground internal melting type ice storage tank is adopted. Energy saving for lighting is achieved with a dimming lighting controlling its lighting output by inverter. The following effects are expected by these new technologies: Load leveling effect of 30%, energy saving effect of 20.2% and CO{sub 2} reduction effect of 24.1%. (NEDO)

  15. Present situation of the electric power storage technology and its future outlook. IV. ; Compressed air energy storage. Denryoku Chozo gijutsu no genjo to shorai tenbo ni tsuibe. IV. ; Asshuku kuki chozo

    Energy Technology Data Exchange (ETDEWEB)

    Kadoyu, M. (Central Research Institute of Electric Power Industry, Tokyo (Japan))

    1991-03-20

    The compressed air energy storage gas turbine power generation system is paid attetion to as a load levelling power source in view of the recent increase in electric power demand. The paper describes features, cavern construction technology, economy and future expansion of the system. In this system compressed air made by use of cheap night-time electric power is stored in underground spaces or underwater facilities. Burning the fuel together with this compressed air in the daytime, the gas turbine power generation is conducted. Several examples overseas of this system are reported including a 290,000KW class in Germany. A key technology of the system is how safely and cheaply a large amount of hih-pressure air can be stored. In Europe and America, caverns of hundreds of thousand m {sub 3} are constructed in the rock salt cavern which can be excavated by a water jet. In consideration of storing it in rock beds in Japan where there are no rock salt caverns, NEDO started 1990 a 9-year construction plan of a 35,000 KW class pilot plant at Kamisunagawa, Hokkaido. 2 refs., 5 figs., 1 tab.

  16. Development of fundamental technigue of compressed air energy storage (CAES) gas turbine power generation and resistivity tomography. Asshuku kuki chozo (CAES) gas turbine hatsuden no kiban gijutsu no kaihatsu to hiteiko tomography

    Energy Technology Data Exchange (ETDEWEB)

    Hibino, S; Suzuki, K [Central Research Inst. of Electric Power Industry, Tokyo (Japan)

    1991-12-01

    Compressed air energy storage (CAES) has been studied as a promising storage system which has a good possibility of being put to practical use. Construction of the storage facility is required for CAES. For an economical construction of a storage facility, it is necessary to construct a storage facility by excavating, from the ground surface, a cavity in the ground. There is no case in Japan where rock storage is adopted with several tens of atmospheric pressure which is necessary for CAES. If highly pressurized air can be stored by the water sealing method, it is a very economical method in the case with hard rocks. As the first stem to verify the effectivity of the water sealing system, a water sealing experiment is performed in a boring hole. It is confirmed that water sealing can be possible up to about 40 atmospheres, and it is found that the resistivity, open joint distribution and coefficient of permeability of rocks have correlation as an investigating method for potential cracks in rocks and that resistivity tomography is effective for the investigation of cracks in rocks. 9 ref., 23 figs., 6 tabs.

  17. Fiscal 2000 survey report. Development of autonomous surface reforming technology by use of multi-energy laser (MEL); 2000 nendo taju ihacho laser (MEL) ho ni yoru chokoshitsumaku no jiko hyomen kaishitsu gijutsu no kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    An experiment was conducted using a MEL (multi-energy laser) method in which multiple laser devices were operated for the formation of an ultra-hard surface reformed layer. At the first step of the research, a carbon-based material was irradiated with various laser beams in an CO2 gas atmosphere, and the hardness, Raman spectrum, etc., of the surface structure were evaluated. As the result, it was found that the formation of diamond like carbon (DLC) texture advances faster when the excited wavelength is longer from ArF laser toward SHG-YAG laser. At the second step, an effort was made to grow DLC out of tungsten carbide. When a normal pulse YAG laser beam was projected on a WC-Co substrate, W was dissociated on the surface for the precipitation of graphite. Next, XeCl excimer laser was projected on the precipitated graphite, and then the graphite was reformed into DLC. In this experiment, transition from graphite to DLC was controlled by changing the delay time lengths of the two laser beams. (NEDO)

  18. Fiscal 1998 research report (continued from the fiscal 1997 project). International survey project for rational energy use / Basic survey on efficient energy use in developing countries (Database construction project) / Survey on Japanese energy conservation technologies; 1998 nendo (1997 nendo jigyo kurikoshi) kokusai energy shiyo gorika nado chosa jigyo hatten tojokoku energy shohi koritsuka kiso chosa (database kochiku jigyo) chosa hokokusho. Nippon no sho energy gijutsu ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-02-01

    As a part of development of the energy conservation technology database, revision was made on 'Directory of Energy Conservation Technology in Japan' which was published to present the energy conservation technology of the Japanese energy-intensive industry to Asian countries in fiscal 1996. The previous directory was composed of 307 technical items, and 126 items among them were deleted and new 63 items were added through this revision. The technologies with energy conservation effects more than 10% were mainly selected by knowledge of the industrial members of the committee and other specialists. The energy conservation effect widely ranges from low-level one to high-level one, and the number of all the energy conservation technologies is enormous. Consequently, it should be considered that the applicable extent of the energy conservation technologies is dependent on the energy cost or economical situation of Japan and developing countries. (NEDO)

  19. Energy supply/demand structure development survey project / comprehensive survey on energy supply/demand development. FY1997 survey on techniques for pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo / energy jukyu kodoka sogo chosa. 1997 nendo shoden hatsuden system no gijutsu chosa seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    Pyroelectric conversion systems were surveyed as the techniques for effective utilization of low-temperature waste heat sources. Described herein are the principle of pyroelectric power generation, including pyroelectric phenomenon, origin of pyroelectricity in polymers, and pyroelectric polymers and copolymers; utilization of the pyroelectric phenomenon, including hysteresis of pyroelectric materials, general pyroelectric conversion principle, pyroelectric conversion cycle, analysis of power output by an Olsen cycle, comparison with a steam engine, and power outputting methods; pyroelectric conversion systems, including heat regeneration method, plate type pyroelectric conversion devices using the heat regeneration method, and voltage controlling methods; and pyroelectric conversion outputting, including calculations of power output and loss, conduction-caused loss, pumping loss, and pyroelectric converter efficiency. Other items described herein include conceptual designs of 1 and 100 kW pyroelectric converters for utilization of waste heat, and current status of pyroelectric converter development at CANMET Energy Technology Center. (NEDO)

  20. Project for surveying improvement in energy demand and supply structure (comprehensive survey on improvement in energy demand and supply). FY1998 report on achievements of Technical survey on pyroelectric power generation systems; Energy jukyu kozo kodoka chosa jigyo (energy jukyu kodoka sogo chosa). Shoden hatsuden system no gijutsu chosa 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    This paper reports the achievements on research of pyroelectric power generation systems in fiscal 1998. In the research, a small continuous pyroelectric conversion equipment was fabricated and experimented. The experiment using an aluminum foil electrode revealed that the foil melts during discharge opening holes, thus making it impossible to increase net conversion efficiency. The net conversion efficiency was derived in an experiment using foil evaporated with indium instead of the aluminum foil. Indium has inferior electric conductivity to aluminum, but is melting point is as low as 145.6 degrees C. Therefore, if a pyroelectric film had electric fatigue due to use over an extended period of time, indium may be melted to make recovering and reusing pyroelectric copolymer possible. Thus, the indium electrode was found suitable for pyroelectric conversion. Analysis of the experimental data indicated that the final possible net output can be 7.6 W/m{sup 2} if each operation variable considered possible in the future is superimposed on the pyroelectric film. This survey revealed that low-temperature waste heat can be converted to high voltage continually by using the pyroelectric conversion equipment at CANMET Energy Technology Centre. (NEDO)

  1. FY 1998 survey report. Survey to prepare a data book related to new energy technology development (Trends on the waste power generation, solar heat utilization, geothermal power generation, clean energy cars, coal liquefaction/coal gasification and new energy); 1998 nendo chosa hokokusho. Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy, jidosha, sekitan ekika gas ka oyobi shin energy kanren doko)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Together with the progress of technology development, policies for the introduction/promotion of new energy technology are being developed such as promotion of the commercialization development, revision of the law system, and expansion of the subsidy system for promotion. To push the introduction/promotion forward more effectively, it is necessary to arrange various kinds of data comprehensively/systematically and to make them the basic data for contribution to the spread/education. As to the six fields of the waste power generation, solar heat utilization, geothermal power generation, clean energy cars, coal liquefaction, and coal gasification of the technology fields of new energy, this report collected/arranged the data made public recently in terms mainly of the following: trends of the introduction in Japan and abroad, policy/law/subsidy system in Japan and abroad, cost, system outline, basic terms, a list of the main affiliated companies and groups, and the nation's outlook for energy introduction and policies of each new energy technology in Japan and abroad, and the trends. Moreover, characteristics by field were described of the state of the commercialization/introduction of new energy technology. (NEDO)

  2. Report on the FY 1999 R and D survey on ultra-high sensitive photoelectric converter; 1999 nendo chokokando koden henkan soshi ni kansuru kenkyu kaihatsu chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    By the ICB method which is one of the ion engineering methods, photomultipliers were formed using organic dye thin films. By changing the energy to bond traps on thin film/metal electrode interface and electric charges by change of acceleration energy of ion beams, a technology was developed for adjusting the optimum operating temperature between -20 degrees C and +100 degrees C. The wide range of operating temperature and favorable SN ratio can be realized. It was made clear that the dark current of the photomultiplier is composed of two components of contribution by the residual charge stored on the interface at photomultiplying and of contribution by charge injection from the Schottky barrier. Based on this, the residual electric charge removal method by heating and applied pulse voltage was developed. The development for practical use was studied of ultra-high sensitive photoelectric converters. As an intelligent photo sensor, a biomimetic visual photosensor was proposed which uses amplification/memory/arithmetic functions and film formation/processability of organic thin films. The paper also described the image sensor. (NEDO)

  3. Survey for preparing the database for R and D of new engines. Waste power generation, solar heat system, geothermal power generation, clean energy vehicle, coal liquefaction/gasification, and combined systems; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Haikibutsu hatsuden, taiyonetsu riyo, chinetsu hatsuden, clean energy jidosha, sekitan ekika gas ka oyobi odanteki tema

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The present developmental conditions and issues of new energies are systematically arranged for effective promotion of their diffusion. One hundred and forty six general waste power generation facilities of 558,000kW are in operation in 1995, and among them 89 facilities supplies 1,080 GWh to power companies. 50 industrial waste power facilities of 247,000kW are in operation. 20,000 solar systems and 180,000 hot water heaters are in operation in 1995. Commercial geothermal power generation facilities of 490,000kW and private ones of 36,000kW are in operation. Introduction of expensive clean energy vehicles is making very slow progress. The pilot study on bituminous coal liquefaction is in promotion mainly by NEDO. The experiment of entrained bed coal gasification in Nakoso was successfully completed, and development of a commercial plant is to be expected. Power rates of 10 power companies were reduced in 1996, and unit purchase prices of surplus power of photovoltaic and wind power generation were also revised. The new menu and unit purchase price were announced in 1996 for surplus power of waste power generation and fuel cell. 67 figs., 284 tabs.

  4. Fiscal 1999 achievement report on regional consortium research and development project. Regional consortium on energy research in its 3rd year (Development of metal forming technology using new energy-efficient process); 1999 nendo sho energy gata shingata process ni yoru kinzoku seikei gijutsu no kaihatsu seika hokokusho. 3

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    An energy-efficient forming technology is developed for heat-resistant hard materials which are difficult to cut and demand much energy for their precision forming. It is hoped that a material Hv1000 in hardness if obtained will enable the manufacture of cutting tools for use under severe conditions. Under the circumstances, a material based on Fe-4.5%Mo-1.5%V-3%Cr is produced with high reproducibility, where a carbide dispersion carburization (CDC) method (vacuum carburization at 1,040 degrees C, second quenching at 800-850 degrees C, and tempering at 160 degrees C) is employed for realizing a very fine structure. This as the tip is combined with the tool, which is then tested for abrasion. As compared with the control material, it is found that the abrasion of the new material is but 33% of that of the control material. Studies are under way for a commercially acceptable constitution which will exhibit Hv1000 after heat treatment and for conditions of CDC treatment. An intermetallic compound TiAlCr, to be obtained by a process of mechanical alloying and pulse discharge sintering, is found to be superplastic. An automobile engine valve is manufactured by an extrusion process and by near-net shape forming, cutting, and grinding. In the manufacture of tungsten bonded ion gun parts by the pulse discharge sintering method, sufficiently high strength is obtained. (NEDO)

  5. FY 2000 report on the results of the technology development of energy use reduced machine tools, etc. Development of the linear motor system for realization of energy conservation and commercialization; 2000 nendo energy shiyo gorika kosaku kiki nado gijutsu kaihatsu seika hokokusho. Shoeneka to jitsuyoka wo jitsugensuru linear motor system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation to the drive system of machine tools widely used as production facilities for automobiles, home electric appliances, etc., the R and D were made of a high efficiency linear motor system of which attention was paid to energy rationalization and environmental loads, and the FY 2000 results were summed up. In the study of the development of the system, studies were made not only on the lowering of heating, cost reduction and heightening of speed, but on the mechanism and control by which machine natural vibration can relatively be cut off, technology of damping for cutting vibration, technology to meet the deformation, etc. by cutting loads, sliding loads, and acceleration of accelerating/decelerating, technology to reduce the machine weight, etc. In the study of the basic technology of linear motor, the finite element method analysis was conducted on the typical linear motor. Concerning the control system, specs were studied which can deal with natural vibration and cutting vibration of the machine system. As to the development of the steel scale type linear encoder, scale sample for evaluation of basic characteristics was designed/trially manufactured. In the study of the detection optical system, the design/trial manufacture of photodiode array were made. (NEDO)

  6. FY 1999 results of the regional consortium R and D project/the regional consortium energy R and D. 1st year. Development of the energy-saving type production technology of high-purity/transparent silica glass; 1999 nendo kojundo tomei sekiei glass no sho energy gata seizo gijutsu no kaihatsu seika hokokusho. 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of achieving the remarkable energy conservation, high accuracy and low cost in the production of high-purity/transparent silica glass, the developmental research was conducted on slip casting method. In the development of technology to synthesize silica powder by the sol-gel method, monodisperse - polydisperse high-purity colloidal silica was obtained. In the development of technology to make silica power ultra-highly pure, a process was found out in which silica particles can be obtained by applying moderate amounts of ammonium bicarbonate and aqueous ammonia to the solution of silicic acid for heating. In the slip cast forming, a high-density forming body with a mean particle size of 1.5{mu}m was obtained. In the trial manufacture of reflector model, a translucent silica glass sintered body was obtained by transcribing the gypsum type dimensional shape in high purity. Besides, experimental researches were conducted on the examination of gypsum type/resin type and evaluation of physical properties, heat deterioration characteristics of the actual multi-layer film and trial manufacture of the heat resistant film, analysis/evaluation of trace impurities inside silica glass, conditions for the manufacture of dense silica glass sheets, etc. (NEDO)

  7. Fiscal 1997 survey report. Subtask 3 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (total system/nation-level energy estimation and assessment); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 3 zentai system ikkoku kibo deno yosoku hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With relation to the energy supply/demand in Japan toward the second half of the 21st century, an analysis was made using the MARKAL model to predict the amount of hydrogen introduction in the future. As in the last fiscal year, conditions of the study of IEA/ETSAP were continuously used. It was decided on that hydrogen was produced by hydroelectric/photovoltaic power generation overseas. Prices were made 14 yen and 27 yen/103 kcal. The limit price of introduction of import hydrogen was calculated. During the period from 2030 to 2050, if the hydrogen price is less than 7 ten/103 kcal, the result showed that hydrogen can be introduced in a lot of scenarios (case of the severe control of CO2 emissions, case of high priced fossil fuels, case of the low capacity of the development of nuclear power generation, etc.) As the form of hydrogen use, promising are the hydrogen combustion turbine power generation, mixture with town gas (hythane) and hydrogen cars. However, a precondition for the introduction is that the cost of hydrogen car should be more economical than the competitive means of transportation. As to hydrogen combustion turbines and hythane, the quantity of hydrogen introduction depends little on variations of characteristics of the equipment used. 11 refs., 55 figs., 21 tabs.

  8. Achievement report on research and development in the Sunshine Project in fiscal 1978. Surveys and studies on patents and information (Surveys on information about new energy technology development); 1978 nendo tokkyo joho chosa kenkyu seika hokokusho. Shin energy gijutsu kaihatsu joho chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    This paper describes the surveys on information about new energy technology development in fiscal 1978 in the Sunshine Project. The present fiscal year performed the surveys on the United States and France as the main subjects. For the solar energy development in the United States, surveys were made on power generation using solar heat, solar cells, difference in ocean temperatures, satellites, biomass, and solar energy air conditioning systems. Geothermal energy development was also surveyed. For coal energy, surveys were done on coal liquefaction, gasification, high-temperature gas turbines and MHD power generation. The U.S. energy policy has various kinds of cards. For the solar energy development in France, heat conversion and photo-cell conversion systems were surveyed, while the authorities take development promotion measures on solar heat conversion system under the judgement that this is the only contributor to the new energy development. Surveys were performed on trends in biomass as the biological energy conversion means of the solar energy. Geothermal energy is being advanced of development following that for the solar energy. Surveys were made also on power generation systems using wind power, wave power and difference in ocean temperatures. This paper dwells also on waste heat utilization, cogeneration, and heat pumps as examples for energy conservation means. (NEDO)

  9. FY 1999 Report on the results of technological development of machine tools for rationalization of energy utilization. Development of a lathe with high precision and conservation of energy using natural phenomenon (Thermal countermeasure using self compulsory cooling and thermal insensitive structure - results of the first year); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Shizen gensho wo takumi ni oyoshita sho energy koseido senban no kaihatsu (self kyosei reikyaku to netsufukan gijutsu wo mochiita netsuhenkei yokusei taisaku - dai 1 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A lathe, which is a central tool in a factory of automobiles or home electric appliances, tends to suffer decreased machining precision resulting from thermal deformation. This project is aimed at development of the energy-saving, high-precision lathe technologies using self compulsory cooling and thermal insensitive technologies as the countermeasures against the thermal deformation. The self compulsory cooling is a method of cooling by evaporation of water with an evaporative, water-absorptive cloth being bonded to a machine tool surface around the major axis. The thermal insensitive technologies include the three-dimensionally zero-center design technologies which help design a lathe in such a way to set the processing point (tool working point) at the base of thermal deformation in the X, Y and Z axis directions; material combination technologies to control thermal deformation; and coloring technologies to control thermal deformation. The development target is the high-precision lathe fabrication technologies, which realize a temporal precision change of 1 to 2 {mu}m or less per work dimension of 100mm. The activities cover 5 areas, including development of elementary technologies for each item and construction/evaluation of the full-size test unit. (NEDO)

  10. Report on the achievements in the Sunshine Project in fiscal 1985. Surveys and studies on arranging commercializing conditions for new energy technologies (a summarized version); 1985 nendo shin energy gijutsu no kigyoka joken seibi ni kansuru chosa kenkyu seika hokokusho. Yoyakuhen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1986-03-01

    The purpose of the present surveys and studies is to discuss positioning of new energies for the case of forming the energy mix for Japan, and measures to arrange the conditions to have the positioning take roots in the society. One of the assignments in the discussion is to propose a system intended of improving the economic performance and of harmonizing with the existing energy systems, by establishing an adequate hybrid system composed of new energies and the existing energies. The current fiscal year will propose a hybrid system for manufacture or composite utilization of 'new synthesized fuels'. Another assignment is to discover a method to analyze quantitatively and evaluate how much the energy supply security in Japan will be improved, what the economic performance would be, and how the improvement effects will relate with cost of developing the new energies as a result introducing the new energies into the society. This fiscal year will analyze the importance of the evaluation factors themselves that make it possible to analyze such a dynamic change as oil crisis, and evaluate effects caused by fluctuation in crude oil price, effects on energy consumption and environment, and the energy mix. (NEDO)

  11. Achievement report for fiscal 1998. Research and development of new technologies for storing farm products utilizing low-temperature energy (2nd fiscal year); 1998 nendo seika hokokusho. Teion energy wo riyoshita nosanbutsu no shinki chozo gijutsu no kenkyu kaihatsu (dai 2 nendo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The aim of the work was to create new industrial technologies utilizing low-temperature energy satisfying local needs through developing new technologies, including air conditioning technologies high in reliability and excellent in energy efficiency. The objectives of the effort were to elucidate the behavior of moisture in the atmosphere below the freezing point and to develop farm product preserving technologies, to develop highly efficient energy conversion technologies for use in the low-temperature zone, latent heat storing cold heat technologies, and system evaluation. Constructed in connection with the last-said system evaluation were three technologies, which were a below-zero high-humidity air conditioning technology based on the outcome of agricultural verification of farm product storage, energy-efficient low-temperature storage of farm products which was a combination of a low-temperature oriented energy-efficient energy conversion technology and a clathrate hydrate-aided cold heat storing technology, and a technology applicable to business in the low-temperature processing field accessorial to the said technologies. They were compared with the conventional technologies, and then it was found that the most energy-efficient system, as endorsed by a 40-50% reduction it caused in electricity rate, was a combination of a low-temperature storage, frozen food storage, hydrate cold heat storage tank, recovery facility for farm waste incineration-produced waste heat, and a pulse tube freezer. (NEDO)

  12. Achievement report for fiscal 2000 on the phase II research and development for the hydrogen utilizing international clean energy system technology (WE-NET). Task 1. Investigations and researched on system assessment; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-1. Technologies drawing attentions relate to fuel cell driven automobiles and hybrid automobiles in the field of utilizing hydrogen derived from reproducible energies and fossil energies, and fuel cell co-generation and micro gas turbine co-generation in the field of electric power generation. Hydrogen reformed from gasoline on board the automobile as the fuel for fuel cell driven automobiles, hydrogen as a by-product of coke furnace off-gas (COG), and reproducible energy hydrogen have the same fuel consumption performance as in the hybrid automobiles. Particularly the COG is low in cost, and has large supply potential. Liquefied hydrogen is as promising as compressed hydrogen in view of the cost for automotive hydrogen supply stations. What has high economic performance as the self-sustaining systems for islands are photovoltaic and wind power generation, and the system using hydrogen as the secondary energy. Since much of the reproducible energies is used for electric power demand in Japan, the by-product hydrogen and the reformed hydrogen in an amount of 9.3 billion Nm{sup 3}/year would take care of majority of the demand in view of the short time period. For a longer time span, hydrogen originated from the reproduced energies in the Pan-Pacific Region should be introduced. (NEDO)

  13. Fiscal 1998 research report on International Clean Energy Network using Hydrogen Conversion (WE-NET). Subtask 3. Prediction evaluation on a national scale; 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) sub task. 3. Ikkoku kibo deno yosoku hyoka

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Japanese long-term energy demand and various energy use styles were simulated from the viewpoint of a profitability and environmental preservation, and hydrogen consumption was studied. In the research in fiscal 1998, the data on available primary energy was modified based on the upper limit of CO{sub 2} emission by COP3, and the long-term energy supply and demand outlook of Advisory Committee for Energy in June, 1998. The result of scenario analysis is as follows: (1) The reference scenario showed that reduction of a hydrogen price is indispensable to use imported hydrogen, (2) The carbon externality scenario showed that market penetration of hydrogen can be large if the carbon externality amounts to $300/t-C, (3) The high fossil fuel price scenario showed that a fossil fuel price (in particular, price of hydrocarbon) highly affects market penetration of hydrogen, and (4) The low nuclear capacity scenario suggested that a competitiveness of hydrogen is considerably improved as an energy supply-demand-balance is tight. (NEDO)

  14. Fiscal 1997 report on the investigational research on the evaluation of a global energy system as global environmental protection technology. 2; 1997 nendo chosa hokokusho (chikyu kankyo taisaku gijutsu to shite no global energy system no hyoka ni kansuru chosa kenkyu). 2

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    An energy supply system which is globally formed for global environmental protection is called a global energy system (GES), in which to achieve substantial CO2 reduction, various measures against CO2 are introduced to energy systems extending from places of fuel supply to places of fuel consumption. For the study of a scenario for introduction such a GES, it is necessary to investigate the GES presently proposed and make a traverse evaluation of it under uniform preconditions and evaluation criteria. Concretely, following a case study of evaluating performance of the GES with a power system as the final form from viewpoints of economy, energy balance, CO2 emissions, etc., the paper arranged characteristics of liquid fuel supply systems including methanol from a traverse aspect, made evaluation of performance and possibilities of the introduction in the areas concretely named, and studied positioning of this energy system, scenario for the future introduction and possibilities of the introduction from global and long-term aspects. 79 refs., 102 figs., 77 tabs.

  15. FY 2000 report on the project for promotion of clean coal technology. Survey of overseas trends of technology to use hydrocarbon base energy such as coal; 2000 nendo clean coru technology suishin jigjyo. Sekitan tou tankasuiso kei energy riyo gijutsu ni kansuru kaigai doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For contributing to the study on the comprehensive development of technology to use hydrocarbon resource such as coal in Japan, survey was conducted of trends of supply/demand, policy, utilization technology, etc. of hydrocarbon base energy such as coal in developed countries such as the U.S., European countries, etc. Proved coal reserves in the world are 980 billion tons, and years of mining are 230. The resource amount of coal is more than those of oil and natural gas. In the U.S., the budget was largely cut in the 1990s because of the financial deficit, but the R and D are being promoted of power plant being aimed at substantial reduction in emissions of NOx, SOx, etc. and reduction in cost. European countries are tackling the technical development of petroleum substituting energy and the verification/commercialization. As to the clean coal technology, every country is making the technical development for coal liquefaction/gasification. Relating to the natural gas technology, studies are being made of GTL, coal bed methane, shale gas, methane hydrate, etc. The energy conversion use of waste, technical development of biomass energy, etc. were also being carried out. (NEDO)

  16. Fiscal 2000 survey report. High-efficiency energy system introduction promotion project for houses and structures - Houses (Technical classification tables prepared by analysis of proposed systems, and comments on the same); 2000 nendo jutaku kenchikubutsu kokoritsu energy system donyu sokushin jigyo (jutaku ni kakawaru mono) teian system no bunseki ni yoru gijutsu bunruihyo oyobi dokaisetsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As an energy conservation promotion measure, a project is under development for introducing and subsidizing high-efficiency energy systems and for letting their effect known publicly and widely. The number of proposed energy systems has increased greatly and technical divisions to follow in classifying them have become vague, from which problems are now arising over the execution of follow-up checks and the maintenance of fair treatment. In the effort to solve this problem, 376 propositions are analyzed and classified, a technical classification method is proposed, and an instruction manual on the method is compiled. The classification involves (1) proposed classification, (2) variation, (3) energy reduction rate, and (4) tentatively calculated cost. Item (1) deals with the basic classification (air-conditioning, ventilation, and hot water supply, and, to be considered in combination with them, options which are cooking, illumination, and others) and, item (2) covers eight items such as new/old construction, structure, and structural frame. In Chapter 1 of the report, the 376 propositions are put in order according to common classification items and an original classification table is prepared. In Chapter 2, the goals are clarified and the classification principles are defined. In Chapter 3, the classification is checked for its validity and some realistic ways of grouping are described. In Chapter 4, a classification implementation flow chart is shown. (NEDO)

  17. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (General research on hydrogen energy subsystems); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso riyo subsystem no sogoteki kento

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-01

    This report is composed of the part 1 'General research on hydrogen energy subsystems' and the part 2 'Outline of researches on every use pattern of hydrogen'. The part 1 outlines the fiscal 1975 activity and result, the latest research situation, the latest domestic and overseas R and D situations, some extracted problems, and the future research issues. The part 2 summarizes the research results of every committee with the following themes: (1) Hydrogen combustion technology (combustion characteristics and technology of hydrogen-methane mixture, home and industrial combustors, study on hydrogen energy system), (2) Fuel cell, (3) Automobile engine (merits and demerits of automobile hydrogen engine, problems and their possible solutions on hydrogen engine, urgent research issues), (4) Aircraft engine (prospect for hydrogen use in air transport in Japan, study on various systems around airports in hydrogen use, technical study on aircraft using hydrogen fuel), (5) Gas turbine, and (6) Chemical use of hydrogen. (NEDO)

  18. FY 1998 annual summary report on International Clean Energy Network Using Hydrogen Conversion (WE-NET) system technology. Subtask 2. Examination and promotion of measures to obtain international understanding and cooperation; 1998 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 2 (kokusai kyoryoku shuishin no tame no chosa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Described herein are the results of examination and promotion of measures to obtain international understanding and cooperation, and examination and development of measures to promote international exchange of technical information, conducted in the FY 1998 continuously from the previous year, with the object to realize the International Clean Energy Network Using Hydrogen Conversion (WE-NET) project. In the FY 1998, the English version of the 1997 annual summary report was distributed to a total of about 150 overseas organizations. The WE-NET project activities were presented to the 12th World Hydrogen Energy Conference, International Joint Power Generation Conference held in 1998 by American Society of Mechanical Engineers, and 2nd International Symposium on Advanced Energy Conversion Systems and Related Technologies. For the examination and development of measures to promote international exchange of technical information, the contracting party of Japan for the Hydrogen Implementation Agreement with IEA has been shifted from the government of Japan to NEDO. NEDO has been representing Japan for various workshops on the tasks. The hydrogen projects conducted by Germany and USA were also surveyed. The WE-NET project homepage was opened in June, 1998. (NEDO)

  19. Report on a survey in fiscal 1999. Survey on trends in developing innovative technologies related to reducing CO2 emission in departments consuming great quantity of energy, such as petrochemical industry; 1999 nendo sekiyu kagaku kogyo nado energy tashohi bumon ni okeru CO{sub 2} sakugen ni kansuru kakushinteki gijutsu kaihatsu doko chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A survey was performed on the state of developing energy saving and CO2 emission reducing technologies in the following fields: (1) distillation technologies, (2) combustion technologies, (3) heat transfer and conduction technologies, and (4) technologies to convert and fix generated CO2. While the technologies in the field (1) are of the matured domain, technologies providing 20 to 60% energy saving effect have been developed. In the field (2), gas turbine combustion can achieve an overall plant thermal efficiency of 50% or more, whereas a trial calculation indicates that CO2 emission can be reduced by 22%. Catalytic combustion is noticed as a measure to make low NOx emission possible. A composite type catalytic combustor for gas turbines demonstrated that NOx emission of less than 5 ppm can be achieved. In the field (3), energy saving effect higher by 52% than in the warm wind room heating system has been obtained. Development has been made on heat storing materials that have phase change temperature of higher than 80 degrees C and large latent heat storage quantity. In the field (4), researches are advanced in a TiO{sub 2} catalyst that uses sunlight. A catalyst that is methanated at high speed with CO2 conversion rate at nearly 100% has been developed. In methanol synthesis, a catalyst that has high selectivity even at low temperatures has been developed. (NEDO)

  20. FY 2000 report on the project on the researcher dispatch type international joint research survey. Survey of the internationalization of research on the effective utilization technology for energy resources; 2000 nendo kenkyusha hakengata kokusai kyodo kenkyu chosa jigyo hokokusho. Energy shigen yukoriyo gijutsu kenkyu kokusaika chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to themes of the research survey which contribute to upgrading/diversification of the effective utilization of energy resources and are important in increasing cooperative relations with overseas countries, survey research was conducted by dispatching investigators. Relating to long-life Si solar cells, research survey was made on the reduction in deterioration of solar cell. Concerning the hydrogen carbonless energy system, the economical efficiency of a natural energy/hydrogen combined system was studied for all areas of Aomori prefecture. About the development of the multiple chamber type artificial pancreas for patients with serious diabetes, study using model dogs was investigated. As to the processing of PVC waste, the mechano-chemical method was discussed in the U.S. The paper further surveyed the following: PDE application to the aerospace field, joint developmental study of the reuse type space transport system by Japan and Russia, treatment/recycling of the electric/electronic equipment waste including toxic substances, technology of the manufacture of nano-particles and evaluation of optical characteristics of nano-structures, etc. (NEDO)

  1. Fiscal 1993 achievement report. International Clean Energy Network Using Hydrogen Conversion (WE-NET) technology (Subtask 8 - Development of hydrogen combustion turbine - Development of main accessories); 1993 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) (Subtask 8. Suiso nensho tabin no kaihatsu - Shuyo hokirui no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    In the first fiscal year 1993 of the project, surveys were conducted about current technologies relative to cold energy-utilizing oxygen production equipment and high-temperature heat exchangers for the development of main accessories for a hydrogen combustion turbine plant. Kobe Steel, Ltd., conducted surveys about very low temperature heat exchangers and cold energy utilization technology used in facilities for gasifying liquid hydrogen or liquefied gas. Daido Hoxan, Inc., in its research on the possibility of air separator performance enhancement through liquid hydrogen cold energy application, studied reduction in power unit requirement, stable power supply responding to changes in load, safety measures, and so forth. Toshiba Corporation conducted surveys and studies about heat conduction improvement techniques and about the type, structure, and materials for heat exchangers for the embodiment of a high-temperature heat exchanger excellent in performance and high in structural soundness. Mitsubishi Heavy Industries, Ltd., aiming to establish basic technologies for heat exchangers, studied efficiency enhancement with low pressure loss, improved hygroscopic moisture removing function, and new materials utilization for achieving high-temperature capability. (NEDO)

  2. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D. Final year report. Development of the measuring control technology supporting energy conservation in the manufacturing process of electronics (Design and trial manufacture of IMI); 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu. Denshi kikirui seizo process no sho energy shien keisoku seigyo gijutsu no kaihatsu - IMI no sekkei to shisaku (saishu nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As measures taken for energy conservation in the manufacturing plant of electronic devices/equipment such as IC, the development was proceeded with a chlorine gas radio sensing system and a liquid crystal driver IC probe, according to the survey results that it is possible to control energy consumption in air conditioning by completely furnishing poisonous gas monitor in clean room and conserve energy related to the manufacture of IC and LSI tester by using Si for IC probe cards. The following four were carried out: 1) development/trial manufacture of chlorine sensing system; 2) development/trial manufacture of LCD (liquid crystal driver) IC probe; 3) support of trial manufacture of key element technology; 4) comprehensive investigational study of IMI (Intelligent Micro-Instrument). In FY 2000, study was focused on 1) and 2). In 1), a planar type micro-structure sensor was developed, and the trial-manufactured system brought favorable results in sensitivity, response speed and reproductivity. (NEDO)

  3. Achievement report for fiscal 1997 on joint research to develop fuel cell technologies for urban energy centers. Research on evaluating life of phosphoric acid fuel cells; 1997 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu kyodo kenkyu seika hokokusho. Rinsangata nenryo denchi jumyo hyoka kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    This paper discusses life evaluation on phosphoric acid fuel cells of urban energy center type for regional energy supply and on-site type to be installed in buildings. Operation characteristics tests and disassembly checks allow to identify factors for voltage decrease, and estimate the life therefrom particularly if the voltage decrease is caused from catalyst activity. The time before 10% decrease value is reached is now about 40,000 hours. The creep analysis method that has been developed recently can predict deformation in full-size reformers nearly exactly, and is effective in operating the reformer and evaluating the life at the design stage. Creep buckling is the critical value, which is caused by ecliptic deformation of internal tubes in the second catalyst layer. In a heat exchanger for fuel gas preheating, carbon in the reformed gas is carbonized and deposited due to catalytic action of nickel in the brazing material that bonds plates and fins in the heat exchanger. Iron also has a possibility of performing catalytic action. In the on-site type 1,000-kW class fuel cells, no structural problems have been presented even after the operation has been stopped. In order to extend time interval between phosphoric acid supply into the cells, it is necessary to reduce difference in the remaining phosphoric acid amounts in the stack lamination direction and in the cell flat surface. (NEDO)

  4. Fiscal 1999 achievement report. Development of technology for machine tool with energy consumption rationalized (Research and development of environment-conscious grinding system); 1999 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Kankyo taiogata kensaku kako system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    A large quantity of coolant is used in the grinding process for ensuring high accuracy and quality in the work. This presents a serious problem from the viewpoint of environmental impact or energy conservation, and now environment-conscious grinding methods requiring no or less coolant are sought for. With a view to answering the demand, efforts are exerted to put to practical use, and improve, an EcoloG grinding technique. The goal is to reduce to half the energy that the grinding process is now consuming. The EcoloG technique is a grinding method under which vegetable oil mist is cooled for lubrication and a small amount of cooling water is fed to the point of grinding for removing chips. In fiscal 1999, a survey was conducted on technical literature, patents, and the like in and out of Japan for the study of the actual state of dry machining, and then the course of future studies was clearly established. Studies were also carried out aiming at the practical application and improvement of the EcoloG grinding technique, and the technique achieved a quality level as high as that of the conventional coolant-aided method in a process of grinding a shaft to have an accurate outer diameter by use of an ordinary wheel head. (NEDO)

  5. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 1. Survey/study concerning system evaluation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 1. System hyoka ni kansuru chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With the aim of formulating a strategy for introducing hydrogen, assessment was carried out on the energy consumption, environmental impacts and cost effiectiveness concerning various hydrogen utilization systems. In regard to soda-electrolysis by-product hydrogen and coke-oven by-product hydrogen, hydrogen supply capacity and cost effectiveness were evaluated. As a result, the two systems were found to have an annual hydrogen supply capacity of 11.52 GNm{sup 3} in total. As to the cost effectiveness, transportation by pipeline was 34 yen/Nm{sup 3}-H{sub 2} in the case of soda-electrolysis by-product hydrogen, and 40 yen/Nm{sup 3}-H{sub 2} in the case of coke-oven by-product hydrogen. An estimated cost of power generation showed 56 yen to 67 yen/kWh in such a system on remote islands as replacing diesel power generation by wind power generation, storing part of the electric energy produced in the form of hydrogen through water electrolysis, and using it as fuel for power generation by the fuel cell unit if wind conditions are unfavorable. Power generation cost on remote islands at present is sometimes in excess of 50 yen/kWh; therefore, this combined system showed promising results. The cost of using wooden biomass was estimated to be 51,000 yen/TOE , whose competitiveness is uncertain. (NEDO)

  6. Achievement report for 1st phase (fiscal 1974-80) Sunshine Program research and development - Hydrogen energy. Research on hydrogen production technology using electrolysis; 1974-1980 nendo suiso energy seika hokokusho. Denki bunkaiho ni yoru suiso seizo gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1981-03-01

    The electrolysis of water is a hydrogen production technology known since early days. But the efficiency of a commercial electrolytic bath is found at 60-70%, which is too low to prepare for future energy systems. A high-temperature high-pressure water electrolysis process is being studied for improving on the efficiency. For the realization of energy efficiency of 90% or higher, the conventional operating conditions of 90 degrees C or lower, 20A/dm{sup 2}, and 1.8-2.0V bath operating voltage will be improved to be higher than 120 degrees C, 20kg/cm{sup 2}, and 40A/dm{sup 2}, and the electrodes will be modified to work down at 1.65V. The tasks to discharge involve the materials (of diaphragms etc.) for constituting electrolytic baths, electrode catalysts, and electrode shapes. Tests are under way using a test plant capable of producing hydrogen at a rate of 4m{sup 3}/hr. In the analysis of water in a solid polymeric electrolyte, a combination of a cation exchange membrane and a catalytic electrode directly junctioned to the membrane operates as a unit cell. Development is under way with a view to realizing a bath operating voltage of 1.65V or lower at 100A/dm{sup 2}. Since this process still wants much basic research and the materials for bath construction for the process are expensive, further development endeavors will have to be exerted. (NEDO)

  7. Technological development of machine tools using less energy in fiscal 2000. Achievement report on research and development of cutting process replacing electric discharge processing; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Hoden kako wo chikansuru sessaku kakoho no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development has been made with an objective to replace the electric discharge processing consuming a large amount of energy and having environmental load, with the cutting process consuming less energy while maintaining the equivalent processing precision. This paper summarizes the achievements in fiscal 2000. Development of cutting tools has made three times or more as many multi-aspect utilization as compared to conventional tools possible by researching the tip shapes. In addition, ultra hard end mill suitable for cutting very hard materials using an ultrasonic cutting head was fabricated on the trial basis, and its cutting capability was verified. In developing the cutting processing heard, a vibration mode possible of cutting with the ultra hard tool was generated, ATC has become possible, and the possibility of cutting hard-to-cut materials was verified. For processing a narrow and deep part, an improved type tool was developed, whereas the practical cutting performance suppressing wear of the blade tip was obtained. To deal with the environment, development and prototype fabrication were performed on a unit having a grease lubricated high-speed main shaft that is considered to be the mainstream in the future. In the operation test at 20,000 min-L, know-how was acquired in relation with the basic performance, manufacture and use of the unit. (NEDO)

  8. Fiscal 1998 R and D report on the human coordination/coexistence robot system (development of practical technology for rational energy use); 1998 nendo ningen kyocho kyozongata robot system no kenkyu kaihatsu (energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report reports the R and D on the human coordination/coexistence robot system possible to perform various works instead of people. As for an intelligent robot hand, 4-finger hand and arm hardware were developed and fabricated, and operation of the assembled system of them was tested. As for a robot platform, a remote control platform, and the interface specifications of command communication and data communication were studied. As for 3-D walk adaptive to land shapes, an analysis environment for a control algorithm and an easy-to-use environment for a virtual platform simulator were prepared. By using this analysis environment, the central part of the walk control algorithm, and a module for forming walk patterns were developed. In the application research on energy saving, various problems on dangerous and harsh conditions in construction and disaster restoration works were analyzed, and the needs of a humanoid robot for such works were studied. (NEDO)

  9. Fiscal 2000 report on results on development of technology for reducing electrical power consumption at standby time and on R and D of energy saving fixing system; 2000 nendo taikiji shohi denryoku sakugen gijutsu kaihatsu seika hokokusho. Sho energy teichaku system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In reference to 20 to 40 cpm letter size monochrome digital copiers, R and D was conducted for the purpose of developing an energy-saving fixing system by the combination of a thin-layer thermal-roller fixing unit and a low-fixing-temperature polymerized toner, with the fiscal 2000 results compiled. In the development of the thin-layer thermal-roller fixing unit, a fixing system suitable for toner characteristics was completed, through the optimization of a temperature-stabilizing cooling fan and by a mechanism for detecting anomalous high temperature at the time of a runaway heater, for example. In the research of the low-fixing-temperature polymerized toner, efforts were made toward improving somewhat weak electrostatic chargeability, which was a conventional problem in toner characteristics, and enhancing the thermal/mechanical durability of the toner. In the method of improving electrostatic chargeability, a new process was developed capable of effectively functioning additives in a toner, attaining a level practically free from problems. In the heat resisting characteristic, its enhancement was achieved by developing a method that checks no fused fixing performance at the time of heating for fixing and that imparts a new heat resistivity to a latex surface layer less susceptible to heat inside a copier. (NEDO)

  10. Report on the survey of the project on the environmentally friendly type energy community field test. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-06-01

    An investigative study was made of the use of waste edible oil as fuel and recycle use of residual food in the food service business. As to the existence/recovery of edible oil, it was found out that waste edible oil of 15.9g/meal per capita was discharged at multiple wide-area distributed shops and that the total amount reached 1,861kl/y in the country. Concerning the technology for using it as biodiesel fuel, Ronford Co., which has the most actual results of the technology, recovers waste edible oil in Kyoto City, refines it and uses it as fuel for the City's garbage truck. About the use of waste edible oil as boiler use fuel, there are examples in Sapporo Grand Hotel, which has been contributing to energy conservation for more than five years. In the assessment of the profitability as project, for the direct combustion for boiler fuel use, the same/large heat supply system is a prerequisite, and for the hot stove loaded type direct combustion, there is an element of the technology development. Therefore, the use as bio-diesel fuel is most expected, though there is a taxation problem. (NEDO)

  11. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D high performance flat panel display technology (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / koseino flat panel display gijutsu no sogo kaihatsu kenkyu (daiichi nendo ) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    One of the subjects in technology supporting the highly information-oriented society which will develop and diversify toward the 21st century is the construction of high grade man/machine interface. For it, high precision/high luminance/energy saving/thin plane displays are strongly requested. This R and D is to indicate models of systematical development in the region of element technology individually existing in the Shikoku area by forming a regional consortium in the industry/universities/government. Creation of new industries by gathering display related enterprises is a first step in a plan to realize `Display Island Shikoku.` As a concrete target, with the use of high-tech diamond semiconducting technology, a development is conducted of the high performance flat panel display using the negative electron affinity (NEA) electron emitter which drastically solves the problems such as luminance, visibility angle and response speed, the subjects on the commercialized liquid crystal flat panel display. 16 refs., 45 figs., 8 tabs.

  12. Report on the survey of the project on the environmentally friendly type energy community field test. Separate volume - reference data. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo (Bessatsu - Sanko shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-06-01

    For the purpose of promoting the effective utilization of biomass resource, an investigative study was made on the development of recycle technology of waste edible oil. In the survey, the following were carried out and the results were summarized: promotion measures for biodiesel oil by the EU, promotion measures for biodiesel oil by other countries including Canada, promotion measures for biodiesel oil by the US's Department of Energy (DOC), actual results of the use of biodiesel oil in Kyoto City, reference data on biodiesel oil in Japan, and tackling toward the promotion of BDF in the Ministry of Agriculture, Forestry and Fisheries. As to the transportation use fuel in the EU in the coming 20 years, biofuel, natural gas and hydrogen seem to be selected. If measures are positively taken, biofuel is expected to be 2%, 6%, 7% and 8% in FY 2005, FY 2010, FY 2015 and FY 2020, respectively. Also, natural gas is expected to be 2% in FY 2010, 5% in FY 2015 and 10% in FY 2020, and hydrogen is expected to be 2% in FY 2015 and 5% in FY 2020. (NEDO)

  13. Achievement report for fiscal 2000 on operational research of human cooperative and coexisting (humanoid) robot system. Development of energy usage rationalizing technology; 2000 nendo ningen kyocho kyozongata robot system un'yo kenkyu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper reports the achievements in fiscal 2000 in the operational research on the human cooperative and coexisting (humanoid) robot system to rationalize energy usage. Operational method and maintenance were studied on the platform hardware that has been developed in the previous fiscal year. Checks were given periodically on the robot platform hardware, and no anomalies were verified in all operation. Verifications were made on the fasteners, additional tightening, fitting of the connectors, battery checks, zero position and step response checks, and output checks on the force component sensor, gyro sensor and G sensor. For the virtual robot platform, discussions were given on the basic movement library for the geography complying three-dimensional walking. Such configurations were constituted that integrated use is possible with the simulator system by connecting the networks, and the user can instruct the CORBA server with the generation of walking movements according to the GUI by using the general purpose WWW browser to connect it to the HTTP server, whose result can be verified by three-dimensional graphics. A method to stabilize the all-axis movement servo model was made open to public. (NEDO)

  14. Fiscal 2000 strategic surveys for respective technical fields. Hydrogen-based energy working group (Analysis of project results relating to hydrogen technology); 2000 nendo bun'yabetsu senryaku chosa hokokusho. Suisokei energy WG (Suiso kanren gijutsu ni kakawaru jigyo seika tou bunseki chosa)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Attention is focused on the molten carbonate fuel cell (MCFC) technology which has enjoyed the largest number of industrial property applications out of hydrogen-related technologies under development by NEDO (New Energy and Industrial Technology Development Organization). The patent application is utilized as a tool for analysis, and endeavors are made to systematize and then analyze the correlations between the tasks to discharge and the results of studies in the process of MCFC development. Findings are described below. It is quite difficult to specify the technology involved by the study of patent abstracts. Since an applicant for patent is inclined to describe the application so that it will cover an extensive scope (or, so that the patent will be taken in a broad sense), it takes much time for researchers other than the applicant to specify the field of technological studies where the application originates. Such being the case, it cannot be easily determined whether or not a patent applied for by a private-sector corporation has its origin in a NEDO-implemented project. In addition, it is found that there is not necessarily a correlationship between the importance of a research and development goal and the number of patents generated. (NEDO)

  15. Fiscal 1997 survey report. Subtask 2 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (survey/study for the promotion of international cooperation); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 2 (kokusai kyoryoku suishin no tame no choa kento)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The survey was aimed at developing the WE-NET as a joint project worldwide by taking concrete measures such PR activities to obtain international understanding and cooperation of WE-NET based on the survey/grasp of researches of research institutes in each country and the developmental trend of hydrogen energy in each of the main countries. Implementing a `long-term vision for the WE-NET international cooperation,` the following measures were taken in fiscal 1997. PR activities were positively developed which coped with the worldwide increasing interest in WE-NET such as delivery to overseas institutions of the fiscal 1996 survey report in English summarized by NEDO and information exchanges, and participation in international conferences and presentation of the research results. From a standpoint of positively proceeding with the international technical information exchange, the following were conducted following fiscal 1996: 1) the evaluation study jointly made with Stanford University of effects of reducing air pollution by introducing hydrogen cars, 2) survey on the U.S. hydrogen project, and 3) preparation for opening of the WE-NET internet home pages. 17 figs., 18 tabs.

  16. FY 2000 report on the results of the R and D of the technology for rationalization of energy utilization and for CO2 fixation using recycled paper; 2000 nendo energy shiyo gorika koshi nado yuko riyo nisanka tanso koteika gijutsu kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In this R and D, the recycled paper, etc. composed mainly of cellulose are degraded (saccharified) up to saccharides in a biological method. The saccharides and CO2 obtained are converted into useful substances such as organic acid using the bacterium function. The aim of the R and D is to develop this conversion (bioconversion) technology and to establish the technology to make an effective use of the recycled paper, etc. as useful chemical raw materials/substances and energy. In FY 2000, study was made mostly of the saccharification and bioconversion. As to the saccharification, conducted were the collection of the bacteria for cellulose degrading enzyme production which have been found so far and the evaluation of degradation of the recycled paper. And, as to the bioconversion, conducted were the survey and isolation of enzyme proteins and genes which are concerned in it in the process toward the formation to organic acid from saccharides and CO2, and the analysis of part of them. In this report, introductory remarks were described in Chapter 1. In Chapter 2, the results were summarized of the study on saccharification of the recycled paper. In Chapter 3, the results were outlined of the study on the bioconversion technology. This technology development was aimed at establishing new high efficiency bio-processes. (NEDO)

  17. Report on the survey of the project on the environmentally friendly type energy community field test. Separate volume - reference data. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo (Bessatsu - Sanko shiryo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-06-01

    For the purpose of promoting the effective utilization of biomass resource, an investigative study was made on the development of recycle technology of waste edible oil. In the survey, the following were carried out and the results were summarized: promotion measures for biodiesel oil by the EU, promotion measures for biodiesel oil by other countries including Canada, promotion measures for biodiesel oil by the US's Department of Energy (DOC), actual results of the use of biodiesel oil in Kyoto City, reference data on biodiesel oil in Japan, and tackling toward the promotion of BDF in the Ministry of Agriculture, Forestry and Fisheries. As to the transportation use fuel in the EU in the coming 20 years, biofuel, natural gas and hydrogen seem to be selected. If measures are positively taken, biofuel is expected to be 2%, 6%, 7% and 8% in FY 2005, FY 2010, FY 2015 and FY 2020, respectively. Also, natural gas is expected to be 2% in FY 2010, 5% in FY 2015 and 10% in FY 2020, and hydrogen is expected to be 2% in FY 2015 and 5% in FY 2020. (NEDO)

  18. Report on the survey of the project on the environmentally friendly type energy community field test. Investigative project for development and commercialization of recycle technology of waste edible oil; 2001 nendo kankyo chowa gata energy community field test jigyo chosa hokokusho. Hai shokuryo yu no recycle gijutsu kaihatsu to jitsuyoka no tameno chosa jigyo

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-06-01

    An investigative study was made of the use of waste edible oil as fuel and recycle use of residual food in the food service business. As to the existence/recovery of edible oil, it was found out that waste edible oil of 15.9g/meal per capita was discharged at multiple wide-area distributed shops and that the total amount reached 1,861kl/y in the country. Concerning the technology for using it as biodiesel fuel, Ronford Co., which has the most actual results of the technology, recovers waste edible oil in Kyoto City, refines it and uses it as fuel for the City's garbage truck. About the use of waste edible oil as boiler use fuel, there are examples in Sapporo Grand Hotel, which has been contributing to energy conservation for more than five years. In the assessment of the profitability as project, for the direct combustion for boiler fuel use, the same/large heat supply system is a prerequisite, and for the hot stove loaded type direct combustion, there is an element of the technology development. Therefore, the use as bio-diesel fuel is most expected, though there is a taxation problem. (NEDO)

  19. Report in fiscal 1999 on the achievements in research and development of the ITS technology using clean energy driven automobiles. Research and development of an efficient utilization system for car rentals in tourist resort areas; 1998 nendo clean energy jidosha wo mochiita ITS gijutsu no kenkyu kaihatsu seika hokokusho. Kankochiyo rentaka koritsuteki riyo system no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the achievements in fiscal 1998 on developing ITS technology using clean energy driven automobiles. Development is intended on an efficient management and control method for EV car rentals in tourist resort areas using the ITS technology from the viewpoints of reducing road traffic load and global environment problems. The development items include a control center system, a system to control battery charging status at the center, a battery charging determination algorithm, and a car navigation and bi-directional communications mounting system. The system development has been completed nearly completely, having attained relatively high user satisfaction. However, because of the experimental rented cars having long mileage, there were few chances of verifying the charge determination algorithm and the functions of the ITS. Investigations were carried out on technological trends in overseas countries on EV and ITS, and on commuter car introduction projects. Structuring the hardware for a commuter EV system is not too difficult if the presently available EV and ITS technologies are used. However, in advancing commercialization, there are such assignments as establishment of software, operation patterns, and interfaces that enhance user convenience and profitability. (NEDO)

  20. FY 2000 report on the results of the technology development of energy use reduction of machine tools. Development of dry cutting use abrasion resistant/lubricous coated tools; 2000 nendo energy shiyo gorika kosaku kikai nado gijutsu kaihatsu seika hokokusho. Dry sessakuyo taimamo junkatsusei hifuku kogu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of energy conservation and reduction of environmental loads of machine tools, study was conducted on the dry cutting which is the cutting with no use of cutting oil, and the FY 2000 results were summed up. The study was made on dry cutting use abrasion resistance/lubricous coated tools coated with the composite membrane of which the cutting life become little lower than that of existing tools using coolant. In the survey of abrasion resistant/lubricous films, it was found out that in the adhesion to ultra-hard substrates, the DLC single-layer film consisting only of carbon indicated the same excellent adhesion as intermediate-layer inserts. As to the synthesis of abrasion resistant/lubricous films, the synthesis of the composite membrane (WC/C membrane) consisting of tungsten carbide (WC) and carbon (C) was made using arc ion plating device. The WC/C membrane is composed of W and C and has the structure in which at nm levels the layer with much W and the layer with less W were alternately piled. Study was made of devices necessary for the development of abrasion resistant/lubricous films and the film formation for drill. (NEDO)

  1. Hydrogen utilization international clean energy system (WE-NET). Subtask 8. Development of hydrogen combustion turbines (development of combustion control technology); Suiso riyo kokusai clean energy system (WE-NET). Subtask 8. Suiso nensho turbine no kaihatsu nensho seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The paper described the fiscal 1996 developmental results of hydrogen burning turbine combustion technology in the hydrogen utilization international clean energy system (WE-NET) project. A test was conducted on an annular type combustor where oxygen is mixed with steam (inert gas) at burner and fired with hydrogen. Appropriate flame shape and cooling/dilution vapor distribution were attempted, and various data on combustion were measured for improvement. Mixture and flame holding were improved by developing a can type combustor (1) where oxygen is diluted with steam after firing oxygen and hydrogen around burner and by strengthening circulation in the combustor. Improvement such as appropriate steam distribution, etc. is needed. A can type combustor (2) was tested in which the premixed oxygen and hydrogen is supplied from scoop and fired with hydrogen. By supplying part of oxygen from the primary scoop, the residual hydrogen and oxygen concentration around the stoichiometric ratio can be reduced. Concentration of the residual oxygen can be measured by the absorption light method, but it is difficult to adopt the non-contact measuring method to hydrogen. An outlook for the gas temperature measuring method was obtained. 12 refs., 121 figs., 27 tabs.

  2. FY 1991 Report on research and development of super heat pump energy accumulation system. Part 2. Construction and operation of the prototype system (researches on elementary techniques and construction and operation of the pilot system); Super heat pump energy shuseki system no kenkyu kaihatsu 1991 nendo seika hokokusho. 2. System shisaku unten kenkyu (yoso gijutsu no kenkyu / pilot system no shisaku unten kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-05-01

    Summarized herein are R and D results of the researches on the chemical heat storage systems, plant simulation techniques and combined systems, and international technical exchanges, for R and D of the super heat pump energy accumulation system. For the high temperature heat storage type (utilizing ammonia complexes), the initial research targets are almost attained, as a result of the designs of a chemical heat storage unit having heat storage capacity of 1,000 kWh. For the high temperature heat storage type (utilizing hydration reactions), a 25 Mcal-scale pilot partial test unit is operated, to study applicability of the practical materials and other operation-related themes. For the low temperature heat storage type (utilizing hydration reactions by solute mixing), a pilot system is operated, to attain heat recovery of 75% or more, heat storage density of 30 kcal/kg or more, and output temperature of 7 degrees C. For the low temperature heat storage type (utilizing clathrates), the evaluation tests by a pilot plant produce heat recovery of 93.2% and heat storage density of 32.0 kcal/kg. In addition, the R and D efforts are directed to, e.g., researches on plant simulation techniques and combined systems. (NEDO)

  3. Achievement Report for fiscal 1997 on developing a silicon manufacturing process with reduced energy consumption. Development of technology to manufacture high quality solar cell silicon substrates; 1997 nendo energy shiyo gorika silicon seizo process kaihatsu. Kohinshitsu taiyo denchiyo silicon kiban seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    It is intended to establish an energy saving type mass production technology to manufacture solar cell substrates by using the electromagnetic casting process. This paper describes the achievements in fiscal 1997. Preliminary experiments were performed for high-performance slicing processing and post-slicing rinsing to reduce the cost by enhancing productivity in the slicing process. Since there is a problem of mixing of contaminating raw materials due to diversification in raw materials, resistance and impurity concentration must be determined on each raw material as the materials for the Czochralski method. Then, the raw materials are sorted out referring to the determination results, and they can be used for the electromagnetic casting process upon optimizing them. As a result of having sliced an ingot of 15-cm square with a length of 40 cm by using a mass-production wire saw, an accuracy of 22.8 {mu}m was attained as intra-face variance when the required cutting time was 476 minutes and the substrate thickness is 348 {mu}, thus having obtained prospect for achieving the standard. Development was made on a water jetting rough cleaning machine to separate and remove slurries (oil and grinding particles) from the substrates after slicing, and an arm robot to accommodate substrates into cassettes, which provided processing velocity of 9 second per substrate. A problem of raising the speed remains to be solved. (NEDO)

  4. Fiscal 1999 phase 2 R and D report of WE-NET (International Clean Energy Network Using Hydrogen Conversion). Task 5. Development of hydrogen vehicle system; 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 5. Suiso jidosha system no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on the safety of hydrogen absorbing alloy tanks for hydrogen vehicle systems and the measuring method of a fuel consumption rate of hydrogen fuel cell powered vehicles. In the impact rupture test of (mini-scale) hydrogen absorbing alloy tanks, the impact 3-point bending test result by drop weight showed no ignition caused by impact and friction energy acting on hydrogen released by rupture of tanks, and the necessity for taking spontaneous ignition of alloys due to fuel leakage into account. The experiment result on deformation and rupture of alloy tanks caused by expansion and contraction of crystal lattices due to hydrogen absorption and desorption showed relatively large deformation due to grain fining only within earlier 10 cycles, and no cracks nor other defects even after 1000 cycles. In the measurement of a fuel consumption rate of hydrogen fuel cell powered vehicles, the study result on flow rate measurement method, full tank method, electric current method, hydrogen balance method and oxygen balance method showed that the electric current method is most simple, accurate and practical. (NEDO)

  5. FY 1991 Report on research and development of super heat pump energy accumulation system. Part 1. Construction and operation of the prototype system (researches on elementary techniques and construction and operation of the pilot system); Super heat pump energy shuseki system no kenkyu kaiahtsu 1981 nendo seika hokokusho. 1. System shisaku unten kenkyu (yoso gijutsu no kenkyu / pilot system no shisaku unten kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-05-01

    Summarized herein are R and D results of the super high performance heat pumps and elementary equipment, for R and D of the super heat pump energy accumulation system. For R and D of the super high performance compression heat pumps, the R and D efforts are directed to tests and evaluation of the pilot plant for the highly efficient type (for heating only), which produce the results of COP exceeding the target of 8; to tests of the anti-corrosion measures for the aluminum heat exchangers for the highly efficient type (for cooling and heating), by which the effective inhibitors are selected. The hybrid systems of the super high performance compression heat pumps and chemical heat storage are also studied in detail. The R and D efforts are directed to construction and operation of the hybrid heat pump system to collect underground heat for the high temperature type (utilizing low temperature heat source), which produce the results of confirming possibility of efficient heat collection for extended periods; and to improvement, construction on a trial basis and operation of the high-speed reciprocating compressors and steam superchargers for the high temperature type (utilizing high temperature heat source). For R and D of the elementary equipment, tests and evaluation are conducted for the EHD heat exchangers which use R123 as the new working fluid. (NEDO)

  6. Achievement report for fiscal 1998 on World Energy Network (WE-NET). Subtask 8. Development of hydrogen combustion turbine (Development of main accessories); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) seika hokokusho. 8. Suiso nensho turbine no kaihatsu (shuyo hokirui no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    This report covers the effort to develop hydrogen-fueled turbines under the international clean energy project. In the development of technologies for the use of liquid hydrogen cold heat, studies are conducted about the emergency stop of an air separating device for a 1,000MW power plant and about a backup system, various details and specifications are defined, and a tentative design is prepared for the whole system. Studies are made about economic efficiency, which lands on a oxygen production cost of 10.92 yen/Nm{sup 3}. In the development of high-temperature heat exchangers, the results are evaluated of the competition which has been under way since 1997 between two entrusted corporations over the topping regeneration cycle technology. In this fiscal year, the evaluation is accomplished by the main accessories development subcommittee, and the Toshiba Corporation wins first place, and the Mitsubishi Heavy Industries, Ltd., second place. It is found, however, that the conceptual designs are both feasible from the technological point of view. In addition, tasks to study for the next project are put together. (NEDO)

  7. Fiscal 2000 project of inviting proposals for international joint research - invitation for international proposal (Power generation No.10). Achievement report on independent distributed type power generation technology of using now-unused gas pressure difference energy; 2000 nendo kokusai kyodo kenkyu teian kobo jigyo - kokusai teian kobo (hatsuden No.10). Miriyo gas atsuryokusa energy ni yoru dokuritsu bunsangata hatsuden gijutsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Development is under way of a power generation system utilizing pressure difference during fuel gas transportation, independent from the outside and installable in the vicinity of the load. It is assumed that power is supplied to a decompression device in a fuel gas supply pipeline. Fuel gas placed under high pressure in the mainline is decompressed upon arriving at a consumer area. The intended technology of utilizing the now-unused pressure difference will be employed for power generation, and energy will be collected accordingly. Activities are conducted in the three fields of (1) the acquisition of heat sources for heating, (2) the development of technologies for compensating for seasonal and daily load variations on gas or power, and (3) the development of control technologies to cope with emergency. In field (1), a system is developed, independent from external heat sources, to operate on an indirect heating system based on a heating furnace. In domain (2), it is proved that high efficiency system operation will be available if the influence of gas pipeline transportation parameters on load variations is analyzed for the effective utilization of the pipeline operating system. (NEDO)

  8. Fiscal 1994 report on technological results. Development of fuel cell technology such as urban energy center (Survey for practical development of optical system of decentralized power source for residential use); 1994 nendo toshi energy center nado nenryo denchi gijutsu kaihatsu seika hokokusho. Minseiyo bunsangata dengen saiteki system jitsuyoka kaihatsu chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    Feasibility study was conducted on the technology for practical application of a several kW class fuel cell for the people's livelihood, particularly, for residential use. The study was made in six areas consisting of study on the present state of technology, conceptual design of a small fuel cell, survey on a promising market, basic concept of cell for residential use, feasibility study on application and on introduction. There is no record of development of the several kW class; while the fuel cell excels in the efficiency of energy utilization and the environmental conservation, its performance greatly deteriorates by start and stop under the present technology. Accordingly, it is a prerequisite that the equipment is for an electric heat combined type and for system interconnection. Also, while it is proper that the cell is phosphate type and that the fuel is natural gas, an innovation is necessary in the technology for reforming the cell and the fuel. The conceptual design revealed the possibility of a power generation system having a generating efficiency of 32%, exhaust heat recovery rate of 30%, and dimension of 75x65x150 cm. On the basis of a feasibility study on the application to the combination of a house and a beauty parlor, an advantage was recognized in the fuel unit cost of 5 yen/meal and the equipment cost of 200-250 thousand yen/kW, with demand estimated for 2.5 million installations nationwide including 950 thousand in natural gas supply districts. (NEDO)

  9. Report of the results of the fiscal 1997 regional consortium R and D project. Regional consortium energy field/R and D of new technology using low temperature energy for storage of agricultural products (first fiscal year); 1997 nendo chiiki consortium kenkyu kaihatsu jigyo. Chiiki consortium energy bun`ya / teion energy wo riyoshita nosanbutsu no shinki chozo gijutsu no kenkyu kaihatsu (daiichi nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The development was conducted of a new technology using low temperature energy in Hokkaido for storage of agricultural products. In this fiscal year, the R and D were conducted of 1) elucidation of behavior of water droplets in the air at below-freezing temperatures and technology to preserve agricultural products, 2) low temperature region high efficiency energy conversion application technology, and 3) latent heat cold storage technology. In 1), it was clarified that the electrostatic capacity system is appropriate as non-contact simple measuring device of moisture distribution in cold air. Freezing temperatures were measured of potatoes, onions and carrots produced in Hokkaido. Equipment to generate moist air at below-freezing temperatures was trially manufactured which is composed of humidifier and freezer. A relation was studied between the humidifying method and the size of particulate water droplet. In 2), an experimental device was trially fabricated of BiTe thermoelectric conversion device. An experimental device for Stirling engine power generation was assembled which was incorporated into the waste incinerator. A basic experimental device of pulse pipe refrigerator was trially fabricated. Single crystals of BiSb semiconductors were made. In 3), it was clarified that gas hydrates of CO2 and C3H8 are promising as refrigerant. 60 refs., 120 figs., 19 tabs.

  10. Demonstration technology development of new hydrogen energy; Shinsuiso energy jissho gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This report describes results of the study on the excess heat generation phenomenon during the electrolysis of heavy water using palladium metals as electrode in FY 1995. For the measurements of excess heat using an open type electrolysis cell during the excess heat generation demonstration model tests, significant excess heat beyond the range of input was not measured both for ICARUS-1 and for ICARUS-2. For the measurements using a fuel cell, high absorbing rate more than 0.85 was stably achieved for highly pure Pd electrode material by heat treatment and surface treatment. The excess heat could be reproduced for plural tests. The heat recovery rate more than 98% was obtained using the NHE type flow calorimetric system. The excess heat measurements using this are examined. For the reactive palladium materials, various materials ranging from single crystal to cold working polycrystal materials were systematically used for the absorbing experiments. Benchmark tests were also conducted through the cooperation with related researchers. 18 refs., 135 figs., 28 tabs.

  11. Fiscal 1996 project on the modeling for effective energy consumption in developing countries under a consignment from NEDO. Recent on the results of the demonstrative study on scrap preheater of electric furnace in the iron making process (for public); 1996 nendo hatten tojokoku energy shohi koritsuka model jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Seitetsu katei ni okeru denkiro no genryo yonetsu sochi ni kakawaru jissho kenkyu seika hokokusho (kokaiyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Indonesia is the biggest iron steel producing country in the ASEAN countries. Most of the production is produced by the electric furnace method in which iron steel scrap is used as a material. However, an energy saving measure in this method, the electric furnace scrap preheater using flue gas, has not yet been spread on a full scale. This R and D is aimed at developing jointly with Indonesia an electric furnace scrap preheater for medium/small size electric furnaces which are adoptable to the present iron making situation in Indonesia and installing it to the electric furnace of the iron making plant in Indonesia for a demonstrative study on energy saving, etc. Spread/expansion of the electric furnace scrap preheater which is an excellent energy saving system targeted expansion of energy saving technology not only of Indonesia, but of ASEAN countries and Japan. In this fiscal year, remodeling of part of the system was made by change of flue gas flow for increasing the energy saving effect, and at the same time, a research study was made of a scrap reheater effective as a total system. Moreover, the paper investigated technical data/information in Japan and overseas. 3 figs., 9 tabs.

  12. Energy

    International Nuclear Information System (INIS)

    Meister, F.; Ott, F.

    2002-01-01

    This chapter gives an overview of the current energy economy in Austria. The Austrian political aims of sustainable development and climate protection imply a reorientation of the Austrian energy policy as a whole. Energy consumption trends (1993-1998), final energy consumption by energy carrier (indexed data 1993-1999), comparative analysis of useful energy demand (1993 and 1999) and final energy consumption of renewable energy sources by sector (1996-1999) in Austria are given. The necessary measures to be taken in order to reduce the energy demand and increased the use of renewable energy are briefly mentioned. Figs. 5. (nevyjel)

  13. Energy

    International Nuclear Information System (INIS)

    Meister, F.

    2001-01-01

    This chapter of the environmental control report deals with the environmental impact of energy production, energy conversion, atomic energy and renewable energy. The development of the energy consumption in Austria for the years 1993 to 1999 is given for the different energy types. The development of the use of renewable energy sources in Austria is given, different domestic heat-systems are compared, life cycles and environmental balance are outlined. (a.n.)

  14. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on hydrogen engine for aircraft); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Kokukiyo suiso engine ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-05-01

    This report summarizes the research results on (1) the prospect of an aviation system based on hydrogen energy, (2) the total system of aircraft based on hydrogen energy, and (3) the performance, structure and specifications of airplanes and engines using synthetic fuel such as hydrogen. In (1), study was made on air transport energy, and prediction was made on the demand of liquid hydrogen assuming conversion of petroleum fuel into hydrogen fuel in the future. In (2), the supply system of liquid hydrogen is essential in conversion of current aircraft fuel into liquid hydrogen. Such supply system over the world is also necessary in conversion into liquid hydrogen for both domestic and international airlines. In (3), in order to discuss the feasibility of liquid hydrogen fuel aircraft, the merit of such aircraft as compared with current aircraft using JP fuel, and whether designing a new airframe or modifying existing airframes, study was made conceptually on the size and capacity of airframe by statistical treatment and analysis of previous conceptual designs. (NEDO)

  15. Energy

    International Nuclear Information System (INIS)

    Bobin, J.L.

    1996-01-01

    Object of sciences and technologies, energy plays a major part in economics and relations between nations. Jean-Louis Bobin, physicist, analyses the relations between man and energy and wonders about fears that delivers nowadays technologies bound to nuclear energy and about the fear of a possible shortage of energy resources. (N.C.). 17 refs., 14 figs., 2 tabs

  16. Energy

    CERN Document Server

    Foland, Andrew Dean

    2007-01-01

    Energy is the central concept of physics. Unable to be created or destroyed but transformable from one form to another, energy ultimately determines what is and isn''t possible in our universe. This book gives readers an appreciation for the limits of energy and the quantities of energy in the world around them. This fascinating book explores the major forms of energy: kinetic, potential, electrical, chemical, thermal, and nuclear.

  17. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on hydrogen gas turbine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Suiso gas turbine ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-03-31

    This research aims at establishment of the meaning of using hydrogen as gas turbine fuel in the hydrogen energy system and various conditions for hydrogen gas turbines, and approaches to the feasibility study and R and D of hydrogen gas turbines in the future. In fiscal 1975, researches were made on (1) feasibility study on hydrogen-oxygen gas turbine, (2) establishment of various conditions for technical, social and economic realization of hydrogen gas turbines in the total energy system, and (3) study on technical troubles to be solved for realization of hydrogen gas turbines. For the above researches, study was made on hydrogen combustion based on the hydrogen combustion test result of gas mixture including hydrogen, and on the feasibility of aphodid cycle. In addition, study on the applicability of hydrogen-oxygen gas turbines, comparative study on hydrogen-oxygen gas turbine, MHD power generation and fuel cell, and the future prospect of hydrogen gas turbines for ships were made to place this hydrogen gas turbine. (NEDO)

  18. Research and development of utilization technology of solar thermal energy system for industrial and other use. Research and development of solar system (investigation of popular type snow melting systems); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Solar system no chosa kenkyu (fukyugata yusetsu system no kenkyu chosa)

    Energy Technology Data Exchange (ETDEWEB)

    Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    Described herein are the results of the FY1994 research program for investigation for popular type snow melting systems using solar energy. Two types of technologies are proposed to utilize solar energy for snow melting in winter and create comfortable environments. One is combined (active plus passive) type, which transfers solar heat it collects by the whole wall surfaces to an attic to heat it totally, and makes the whole roof as a radiator to melt snow. However, heat radiated from the roof is insufficient to melt all snow on the roof, allowing it to remain to an extent that it works as an insulator. The other is active type, which transfers heat it collects by the collector to the heat storage tank, from which heat is extracted in winter for various purposes, including snow melting. Such a system must store heat for an extended period, for which a highly insulating heat storage tank is proposed to balance capacity of heat storage between seasons and building size.

  19. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on automobile engine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-05-10

    This report summarizes the fiscal 1975 research results, and proposes the policy toward the future as follows. (1) Computational prediction on the future trend of hydrogen energy is active in the U.S.A. (2) For application of hydrogen derived from coal to transport, chemical synthesis of methane, methanol and gasoline from such hydrogen is in proposal because of difficult transport of LH{sub 2} or MH{sub 2}. (3) Complete run of Musashi Institute of Technology's LH{sub 2} passenger car in a long-distance rally, and trial run of Billings' MH{sub 2} minibus as challenge to practical use indicated new data, features and problems for hydrogen vehicles through experiences. (4) Conversion from a conventional soft-oriented attitude to a hard-oriented one is thus necessary. (5) Preparation of LH{sub 2} production facility is also necessary. (6) Stabilization of atomic hydrogen, expected various hydrides, and an H{sub 2}-O{sub 2}-water engine as new ideas are stimulating many researchers. (7) Study on gasoline cracking methods such as JPL is active. (8) Doubled cost of gasoline will probably promote practical use of hydrogen vehicles. (NEDO)

  20. Fiscal 1975 Sunshine Project research report. General research on hydrogen energy subsystems and their peripheral technologies (Research on automobile engine); 1975 nendo suiso riyo subsystem no sogoteki kento to shuhen gijutsu ni kansuru kenkyu seika hokokusho. Jidosha engine ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1976-05-10

    This report summarizes the fiscal 1975 research results, and proposes the policy toward the future as follows. (1) Computational prediction on the future trend of hydrogen energy is active in the U.S.A. (2) For application of hydrogen derived from coal to transport, chemical synthesis of methane, methanol and gasoline from such hydrogen is in proposal because of difficult transport of LH{sub 2} or MH{sub 2}. (3) Complete run of Musashi Institute of Technology's LH{sub 2} passenger car in a long-distance rally, and trial run of Billings' MH{sub 2} minibus as challenge to practical use indicated new data, features and problems for hydrogen vehicles through experiences. (4) Conversion from a conventional soft-oriented attitude to a hard-oriented one is thus necessary. (5) Preparation of LH{sub 2} production facility is also necessary. (6) Stabilization of atomic hydrogen, expected various hydrides, and an H{sub 2}-O{sub 2}-water engine as new ideas are stimulating many researchers. (7) Study on gasoline cracking methods such as JPL is active. (8) Doubled cost of gasoline will probably promote practical use of hydrogen vehicles. (NEDO)

  1. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir mass and heat flow characterization (Development of seismic monitoring technology - Summary); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (jishinha tansaho kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Development is under way of a reservoir mass and heat flow characterization method using seismic wave analysis. Specifics of the endeavor cover detailed studies of techniques for monitoring and analyzing seismic wave changes due to changes in the reservoir that accompanies production and reinjection of geothermal fluids, which are carried out through preliminary monitoring accomplished at the test field. For the construction of a microearthquake monitoring network, a monitoring network design is prepared, a data processing/analyzing system is improved and tested for serviceability, analysis programs for 3-dimensional velocity structure analysis technology are improved, and methods for analyzing changes in the reservoir are deliberated, all these based on the results of microearthquake preliminary monitoring and simulation carried out at the Akinomiya district, Akita Prefecture. For the research of elastic wave velocity structure change, short-duration reflection events and waveform changes due to geothermal power plant periodic inspections are extracted, and studies are conducted about the applicability of the diffraction stacking method to the exploration of geothermal energy. (NEDO)

  2. Fiscal 1995 coal production/utilization technology promotion subsidy/clean coal technology promotion business/regional model survey. Study report on `Environmental load reduction measures: feasibility study of a coal utilization eco/energy supply system` (interim report); 1995 nendo sekitan seisan riyo gijutsu shinkohi hojokin clean coal technology suishin jigyo chiiki model chosa. `Kankyo fuka teigen taisaku: sekitan riyo eko energy kyokyu system no kanosei chosa` chosa hokokusho (chukan hokoku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The coal utilization is expected to make substantial growth according to the long-term energy supply/demand plan. To further expand the future coal utilization, however, it is indispensable to reduce environmental loads in its total use with other energies, based on the coal use. In this survey, a regional model survey was conducted as environmental load reduction measures using highly cleaned coal which were taken in fiscal 1993 and 1994. Concretely, a model system was assumed which combined facilities for mixed combustion with coal and other energy (hull, bagasse, waste, etc.) and facilities for effective use of burned ash, and potential reduction in environmental loads of the model system was studied. The technology of mixed combustion between coal and other energy is still in a developmental stage with no novelties in the country. Therefore, the mixed combustion technology between coal and other energy is an important field which is very useful for the future energy supply/demand and environmental issues. 34 refs., 27 figs., 48 tabs.

  3. Aliasing characteristics of tau-P transform and is application to signal and noise separation; Tau-P henkan no aliasing tokusei to hakei iji wo koryoshita S/N bunri

    Energy Technology Data Exchange (ETDEWEB)

    Kawabuchi, H; Rokugawa, S; Matsushima, J; Ichie, Y [The University of Tokyo, Tokyo (Japan); Minegishi, M; Tsuburaya, Y [Japan National Oil Corp., Tokyo (Japan). Technology Research Center

    1997-05-27

    With respect to the tau-P transform method as a signal and noise (S/N) separation technology used in seismic exploration using the reflection method, a discussion has been given on conditions for the post S/N separation by the tau-P transform to function more effectively. Averaging the energy in performing the tau-P transform makes the wave energy scatter to a certain range. As a result, an aliasing phenomenon appears, in which noise is superimposed on the post-processing record. As a result of the discussion, it was verified that satisfying the two equations of G. Turner is effective in order to reduce the aliasing and maintain the relative amplitude. However, in actual calculation accuracy, waveform change was recognized to some extent, particularly amplification of events in low frequencies, and low restorability in higher frequencies. It was also observed that a method to give the tau-P region a two-dimensional Fourier transform and perform the same processing as an f-k filter can remove aliasing more simply and effectively than the HVF, and improve the S/N ratio maintaining the amplitude at the current level. 5 refs., 13 figs.

  4. Energy

    CERN Document Server

    Robertson, William C

    2002-01-01

    Confounded by kinetic energy? Suspect that teaching about simple machines isn t really so simple? Exasperated by electricity? If you fear the study of energy is beyond you, this entertaining book will do more than introduce you to the topic. It will help you actually understand it. At the book s heart are easy-to-grasp explanations of energy basics work, kinetic energy, potential energy, and the transformation of energy and energy as it relates to simple machines, heat energy, temperature, and heat transfer. Irreverent author Bill Robertson suggests activities that bring the basic concepts of energy to life with common household objects. Each chapter ends with a summary and an applications section that uses practical examples such as roller coasters and home heating systems to explain energy transformations and convection cells. The final chapter brings together key concepts in an easy-to-grasp explanation of how electricity is generated. Energy is the second book in the Stop Faking It! series published by NS...

  5. Energy

    International Nuclear Information System (INIS)

    1975-10-01

    On the occasion of the World Environment Day the Norwegian Ministry for the Environment held a conference on growth problems in energy consumption. The themes which were treated were energy conservation, hydroelectric power, the role of nuclear power, radioactive waste disposal, fossil fuel resources, ecological limits, pollution and international aspects. Nuclear energy forms the main theme of one lecture and an aspect of several others. (JIW)

  6. Energy

    OpenAIRE

    Torriti, Jacopo

    2016-01-01

    The impact of energy policy measures has been assessed with various appraisal and evaluation tools since the 1960s. Decision analysis, environmental impact assessment and strategic environmental assessment are all notable examples of progenitors of Regulatory Impact Assessment (RIA) in the assessment of energy policies, programmes and projects. This chapter provides overview of policy tools which have been historically applied to assess the impacts of energy policies, programmes and projects....

  7. Energies

    International Nuclear Information System (INIS)

    2003-01-01

    In the framework of the National Debate on the energies in a context of a sustainable development some associations for the environment organized a debate on the nuclear interest facing the renewable energies. The first part presents the nuclear energy as a possible solution to fight against the greenhouse effect and the associated problem of the wastes management. The second part gives information on the solar energy and the possibilities of heat and electric power production. A presentation of the FEE (French wind power association) on the situation and the development of the wind power in France, is also provided. (A.L.B.)

  8. Fiscal 2000 report on the Phase II R and D of the international hydrogen utilization clean energy network system technology (WE-NET). Task 3. Survey and research on international cooperation - 1 (Promotion of international cooperation); 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu seika hokokusho. 3. Kokusai kyoryoku ni kansuru chosa kenkyu - 1 (kokusai kyoryoku suishin no tame no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    International research cooperation was promoted and technical information was internationally exchanged for the development of the International Clean Energy Network Using Hydrogen Conversion (WE-NET) Project into a truly international cooperation project. In the promotion of international research cooperation, a collection of summarized achievement reports for fiscal 1999 translated into English, based on achievement reports on the respective tasks, was disseminated to 157 related organizations overseas. Activities related to the WE-NET Project were actively presented at international conferences. For research cooperation at IEA (International Energy Agency), engineers were dispatched to its committees and annexes specializing in hydrogen related implementation agreements. In the international exchange of technical information, overseas surveys were conducted for fulfilling the purposes of the respective WE-NET tasks. Investigations were conducted into the latest fuel cell development status across the world, not to mention the automotive fuel cell now attracting earnest attention. Moreover, surveys were conducted of hydrogen energy related research institutes abroad, and a Japanese booth was installed at Hyforum 2000 (The International Hydrogen Energy Forum 2000). (NEDO)

  9. Development of high-efficiency electric-optic conversion compound semiconductor - Lighting of the 21st century. Collection of essays; Kokoritsu denko henkan kagobutsu handotai kaihatsu (21 seiki no akari) seika ronbunshu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-10-01

    Collected in this volume are essays made public in 1998-2001 under the above-named development project intended at the practical application of an illumination light source using light-emission diodes (LED) whose energy consumption efficiency will be approximately twice as high as that of the fluorescent lamp. The project aims to develop a blue/ultraviolet LED capable of high-efficiency light emission at approximately 400 nm and a fluorescent substance capable of efficient radiation of white light as excited by the said LED and to eventually combine the two for the embodiment of a 80-100 lm/W light source device. Being conducted in the field of basics of physical properties, light-emission mechanism, and crystal growth are the elucidation of the physical properties and light-emission mechanism of GaN-based compound semiconductor materials, basic studies of bulk single crystal GaN grown by the solution growth method, studies of substrate crystal surface properties, research and development of GaNAsP-based multi-color luminescent materials, etc. Studies are also under way for the research and development of LED substrates, epitaxial LED devices, and light-source devices. (NEDO)

  10. Fiscal 1999 hydrogen utilization international clean energy system technology (WE-NET). Phase 2 R and D (Task 3) -research/study concerning international cooperation (Volume 1. research/study for promoting international cooperation); 1999 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dainiki kenkyu kaihatsu. Task 3. Kokusai kyoryoku ni kansuru chosa kenkyu (1. kokusai kyoryoku suishin no tame no chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Various measures were implemented with the aim of realizing the 'longterm vision for international cooperation' in connection with hydrogen utilization international clean energy system technology (WE-NET) formulated in fiscal 1996. The English version of the 1998 annual summary report on results was distributed to approximately 170 pertinent organizations overseas. To develop understanding of the WE-NET project, presentations were given in numerous international conferences. In addition, as research cooperation in IEA (International Energy Agency), specialists were dispatched to the hydrogen implementation committee, the corresponding committee to hydrogen implementation agreement, and to each annex. In international exchange of technical information, each WE-NET task exchanged information with organizations abroad through overseas survey and conducted research on European hydrogen project, for example. With the purpose of developing understanding of WE-NET project activities, a preparatory work was done for participation in HYFORUM2000 (Germany) and World Hydrogen Energy Conference (Beijing) which will be held in 2000. (NEDO)

  11. Fiscal 1996 coal production/utilization technology promotion subsidy/clean coal technology promotion business/regional model survey. Study report on `Environmental load reduction measures: feasibility study of a coal utilization eco/energy supply system`; 1996 nendo sekitan seisan riyo gijutsu shinkohi hojokin clean coal technology suishin jigyo chiiki model chosa. `Kankyo fuka teigen taisaku sekitan riyo eko energy kyokyu system no kanosei chosa` chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Oil demand is expected to substantially grow in the future, and the use of oil with combustibles such as hull, baggase and waste is considered from an effective use of energy. A regional model survey was conducted as measures to reduce environmental loads where the fuel mixing combustion with coal and other energy is made the core. The domestic production amount of hull is 2.4-3.0 tons/year, which have a heating value of 3,500 kcal/kg. If hull can be formed into the one storable for a the long term (the one mixed with low grade coal, etc.), it can be a fuel for stable supply. Bagasse is produced 100 million tons/year, which have a heating value of 2,500 kcal/kg. Among wastes, waste tire, plastics, waste, sludge, etc. have a lot of problems in terms of price and environment, but each of them has a heating value during 3,000-10,000 kcal/kg. As to the coal combustion, the pollutional regulation on it is strict, and much higher processing technology is needed. The technology of coal fuel mixing combustion with other energy has not risen higher than the developmental level. Though the technology is a little bit higher in price than the coal fuel single combustion, it is viable. 38 refs., 32 figs., 65 tabs.

  12. Winter concrete; Kanchu kunkurito. Gijutsu no genjo to shorai tenbo

    Energy Technology Data Exchange (ETDEWEB)

    Kamata, Eiji [Hokkaido University, Hokkaido (Japan)

    1998-11-10

    Much energy is consumed in order to carry out the winter concrete, and it becomes not always the work in the work environment of the amenity. Therefore, it wants to avoid it, if such work is possible. The winter concrete is a basis in carrying out the construction in cold region in all year. Large role is very much fulfilled for efficient operation of the construction industry in which foot of maintain is wide, activation of the regional economy of snows cold region such as the constant employment of construction worker, improvement in the social environment. Therefore, the popularization of the winter concrete technology is indispensable in the chilly snowy area, and it becomes the importance that the efficiency improvement is attempted. (NEDO)

  13. FY 1991 Report on research and development of super heat pump energy accumulation system. Material for explanation (Construction and operation of the prototype system - researches on elementary techniques and construction and operation of the pilot system); Super heat pump energy shuseki system no kenkyu kaihatsu 1991 nendo seika hokokusho. Setsumei shiryo (system shisaku unten kenkyu (yoso gijutsu no kenkyu / pilot system no shisaku unten kenkyu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-05-01

    Summarized herein are R and D results of the researches on the super heat pump energy accumulation system, obtained from FY 1985 to 1991. For R and D of the super high performance compression heat pumps, the R and D results of the elementary techniques and bench and pilot plant operation are summarized for the highly efficient type (for heating) and highly efficient type (for cooling and heating), and high temperature type (utilizing high temperature heat source) and high temperature type (utilizing low temperature heat source). Described are patent application list, designated know-hows, and conclusions. For the elementary equipment and working fluids, the R and D results are summarized for the evaporators for mixed solvents, EHD condensers, and working fluids (alcohol-based fluids and application characteristics of new fluids) and working fluids (nonalcohol-based fluids and basic properties of new fluids). For the chemical heat storage techniques, the R and D results are summarized for the high temperature heat storage type (utilizing metathesis reactions, ammonia complexes and hydration reactions), and low temperature heat storage type (utilizing clathrates, hydration by solute mixing and solvation). (NEDO)

  14. FY 2000 report on the results of the regional consortium R and D project - Regional consortium energy R and D field. First year report. Development of the production technology of clean hydrogen, etc. by direct methane reforming method; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo - chiiki consortium energy kenkyu kaihatsu bun'ya. Methane chokusetsu kaishitsuho ni yoru clean suiso nado no seizo gijutsu kaihatsu (dai 1 nendo) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The development was proceeded with of the hydrogen production method using the zeolite-base methane dehydrogenation cyclization catalyst with the specific porous structure. In this production method, there is no emission of process CO2, and hydrogen can be produced by supply of energy of 1/10 of that in the conventional technology. In FY 2000, the following were conducted: 1) conceptual design of a demonstrative experiment plant; 2) development of catalyst processing technology; 3) development of element technology such as improvement of catalyst performance. In 1), design/specifications for demonstrative experiment use plant were fixed by design estimation and process analysis using the mid-term fluidized bed experiment device. It was decided that the mid-term fluidized bed experiment device will be constructed to evaluate the methane reforming performance of catalyst and that the reaction tower should be the stationary fluidized bed type. In 2), a catalyst activity experimental device 100 times as large as the laboratory was fabricated to evaluate the catalyst performance. By optimization of reaction conditions and preparation of the catalyst composition, the targeted catalyst system was obtained. (NEDO)

  15. Automobiles and safety; Jidosha gijutsu. Jidosha to anzen

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, K.; Goto, T.; Shimizu, T.; Yamanaka, A. [Toyota Motor Co. Ltd., Aichi (Japan)

    1998-08-01

    The number of road traffic victims in Japan has been above the level of 10,000 annually during 8 consecutive years, but in 1996 and 1997, it becomes below this level. The casualty of road traffic accidents is found to be occurred during driving and senior persons account for a large part among victims while 55.1% of the case took place at night. As for the countermeasures, it is possible to indicate the regulatory strengthening, advancement of accident investigation and analysis, provision of safety information to the user and research and development of advanced safety vehicle (ASV). Concerning preventive safety, studies on the human recognition, systems for assisting judgement and running and so on can be enumerated. The ASV is in the course of 2nd program that lasts until 2001 with 6 safety research subjects such as prevention, collision, automatic operation, containment of disaster from expanding and so forth. In terms of post-accident safety, remarkable research and development have been conducted on collision by means of dummy and human body, human resistance against injury, air bag for rider protection and child seat, and especially the form comparison of interior materials for head protection apparatus as well as study via simulation, together with commercialization of side bag for reducing head damages. As for car body materials, energy absorption by pillar type elements, use of aluminum materials, resistance comparison and design concept of structural separation and so on are being carried out. 69 refs., 1 fig.

  16. Photon technology. Laser process technology; Photon technology. Laser process gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For developing laser process technology by interaction between substance and photon, the present state, system, R and D issues and proposal of such technology were summarized. Development of the photon technology aims at the modification of bonding conditions of substances by quantum energy of photon, and the new process technology for generating ultra- high temperature and pressure fields by concentrating photon on a minute region. Photon technology contributes to not only the conventional mechanical and thermal forming and removal machining but also function added machining (photon machining) in quantum level and new machining technology ranging from macro- to micro-machining, creating a new industrial field. This technology extends various fields from the basis of physics and chemistry to new bonding technology. Development of a compact high-quality high-power high-efficiency photon source, and advanced photon transmission technology are necessary. The basic explication of an unsolved physicochemical phenomenon related to photon and substance, and development of related application technologies are essential. 328 refs., 147 figs., 13 tabs.

  17. Photon technology. Hard photon technology; Photon technology. Hard photon gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For the application of photon to industrial technologies, in particular, a hard photon technology was surveyed which uses photon beams of 0.1-200nm in wavelength. Its features such as selective atom reaction, dense inner shell excitation and spacial high resolution by quantum energy are expected to provide innovative techniques for various field such as fine machining, material synthesis and advanced inspection technology. This wavelength region has been hardly utilized for industrial fields because of poor development of suitable photon sources and optical devices. The developmental meaning, usable time and issue of a hard photon reduction lithography were surveyed as lithography in ultra-fine region below 0.1{mu}m. On hard photon analysis/evaluation technology, the industrial use of analysis, measurement and evaluation technologies by micro-beam was viewed, and optimum photon sources and optical systems were surveyed. Prediction of surface and surface layer modification by inner shell excitation, the future trend of this process and development of a vacuum ultraviolet light source were also surveyed. 383 refs., 153 figs., 17 tabs.

  18. NEDO Forum 2000. Geothermal technology development session (new development of geothermal energy); Chinetsu gijutsu kaihatsu session. Chinetsu energy no shintenkai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-09-01

    The following themes were presented at this session: (1) geothermal development in the future, (2) the current status of geothermal development and utilization, (3) surveys on the promotion of geothermal development, and (4) verification and investigation on geothermal exploration technologies, development of hot water utilizing power generation plants, and international cooperation on geothermal development and utilization. In Item 2, report was made on the current status of geothermal power plants in Japan and their future development targets, long-term overview of geothermal development, measures and budgets to achieve the targets of geothermal development. In Item 3, it is reported that out of 48 areas completed of the survey (including the new promotion surveyed areas), the areas possible of steam power generation and confirmed of temperatures higher than 200 degrees C are 30 areas, and the areas possible of binary power generation (using down hole pumps) and small to medium scale power generation, confirmed of temperatures of 100 to 200 degrees C are 13 areas. In Item 4, reports were made on the reservoir bed variation exploring method, surveys on deep geothermal resources, a 10-MW demonstration plant, a system to detect well bottom information during excavation of geothermal wells, a technology to collect deep geothermal resources, and a hot-rock using power generation system. In Item 5, geothermal exploration in remote islands in the eastern part of Indonesia, and the IEA cooperation projects were reported. (NEDO)

  19. Improvement of the efficiency characteristics on the photovoltaic generation system based on a generation control circuit. Part 3. Research on architectural systematization of energy conversion devices; Dosaten seigyo kairo wo mochiita taiyo denchi hatsuden koritsu no kaizen. 3. Energy henkan no kenchiku system ka ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, T.; Ito, N.; Kimura, G.; Fukao, S.; Sunaga, N.; Tsunoda, M.; Muro, K. [Tokyo Metropolitan University, Tokyo (Japan)

    1996-10-27

    In introducing a photovoltaic power generation system to urban homes, the general practice is to install a large number of solar cell panels on the roof. However, as is often the case, a part of the solar cell panels is in the shadows (partial shadows) of neighboring homes, electric poles, cables and trees. Under the circumstances, studies were made on the numerous changes in the lowered generating capacity of individual solar cells by the partial shadows. Developed by the authors were the generation point control principle, in which the generation point was individually controlled on serially connected plural solar cell modules, and a practical circuit system based on that principle with the effects verified in a field test. In the test, the generated power of the system was 476W without partial shadows, and was 323W with partial shadows and without the operation of the generation point control circuit, increasing to 406W with partial shadows and with the operation of the circuit. As a result, compared with the case where no generation point control circuit was employed, the effectiveness of the proposed circuit was evident. 3 refs., 10 figs., 1 tab.

  20. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy (Textile technology field)); 1999 nendo choki energy gijutsu senryku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sen'i gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a textile technology field. Social demand and constraint in the 21st century restrict human life and industrial activity, however, include huge business chances. This technology strategy aims at construction of textile business contributing to the society, and improvement of the international competitiveness of Japanese textile industry. Analysis was made on the current international competitiveness of the textile industry in comparison between Japanese and American productivity. As factors hindering technological innovation, the following were pointed out: poor cooperation among industry, academia and government, poor cooperation among different kinds of industries, poor preparation of basic technology, knowledge base and creation base, and poor deregulation. As the future target and strategy, 7 technology targets, 2 creation targets, and every target year were showed. 4 proposals were also showed as follows: preparation of a technology base, creation base, talent education and knowledge base, and protection of intellectual property rights. (NEDO)

  1. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Aerospace technology field (Aircraft technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (kokuki gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of an aircraft technology field. In an aircraft field, since the major theme is application of new technologies to new airframe development, with joining in international cooperative development of aircraft, Japanese initiative development of airframes based on the domestic market demands and profitability should be started as early as possible. Because there is no airframe development by only one country including U.S.A., Japan is profitable to unite with some overseas companies, and invest selectively in specific leading fields. Positive technical support to safety, reliability, comfort and environment harmony are also important. More important theme than establishment of elementary technologies is preparation of an integrated flight demonstration system to expand application chances of development results, and preparation of various test facilities for tests required during development activities. Application of information technologies to the whole aircraft industry, and organic cooperation between the private and public sectors are also important. (NEDO)

  2. FY 2000 report on the survey on the long-term energy technology strategy. Fundamental survey to work out industrial technology strategies (technology strategy by field - material technology field); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of constructing the material technology strategy, conducted were study of the trend of technical development, arrangement of material technology seeds, and survey of the R and D environment. Concretely, the paper carried out the grasp of the national projects related to materials in Europe and the U.S., patent registration (U.S.-Japan comparison)/application (Europe/Japan), transfer of technology trade, and survey of the trend of papers made public in scientific magazines. Further, in the survey of the R and D environment, conducted were how to treat researchers/engineers, how to handle intellectual ownership, system to promote the cooperation among industry/university/government, and comparison among countries in policies of technology such as patent strategy. The results of the survey were classified into the following 4 items: 1) trend of the technical development in the material technology field; 2) developmental environment in the material technology field; 3) competitive force in the material field and material user needs/seeds maps; 4) proposal for the material technology strategy. As to the competitive force of material technology in 3), the paper took up organic/polymer, iron/steel, aluminum, semiconductor, and ceramic materials. (NEDO)

  3. Energies; Energies

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    In the framework of the National Debate on the energies in a context of a sustainable development some associations for the environment organized a debate on the nuclear interest facing the renewable energies. The first part presents the nuclear energy as a possible solution to fight against the greenhouse effect and the associated problem of the wastes management. The second part gives information on the solar energy and the possibilities of heat and electric power production. A presentation of the FEE (French wind power association) on the situation and the development of the wind power in France, is also provided. (A.L.B.)

  4. Fiscal 1997 R and D project under a consignment from NEDO. R and D of the femtosecond technology (R and D of the monitoring system using high-intensity X-ray pulse for power plants); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Femto byo technology no kenkyu kaihatsu (kokido X sen pulse riyo hatsuden shisetsu monitoring system no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports the result on R and D of the femtosecond technology in fiscal 1997. Ultrahigh-speed electronic technology is indispensable for industrial basic technologies supporting the advanced information society in the 21st century. Control technology of photonic and electronic states in a femtosecond region is essential. In R and D of metrological technology using ultra-short light-pulses, study was made on generating and controlling technology for ultra- short light/electron beam pulses. Ti-sapphire mode-locked laser was prepared, and it was found that time-fluctuation of mode-locked laser pulses is measurable up to 100 femtosecond level. As measures against an instability of gain-switching semiconductor laser, light injection from the outside was effective. The stable directivity of laser beam was obtained by regenerative amplifier, while less temperature variation of an optical switch was necessary to stabilize energy. To generate femtosecond high-intensity X-ray pulse by collision of laser and electron beams, it was confirmed that sub- picosecond synchronization is possible by RF and picosecond laser synchronization circuit. 48 refs., 89 figs., 11 tabs.

  5. Fiscal 1999 research report on long-term energy technology strategy. Pt. 2. Basic research on industrial technology strategy (Individual technology strategy.) Material technology field (Fine ceramics); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. 2. Sangyo gijutsu senryaku sakutei kiban chosa (bun'ya betsu gijutsu senryaku) zairyo gijutsu bun'ya (fine ceramics gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the basic research result on industrial technology strategy for a glass field. Japan is facing such various economic problems as attack by developing countries, collapse of economic babble and yen's appreciation, and environment problems over a period of several years, and a glass industry is also under the influence of such problems. For continuous development of Japan and improvement of the international competitiveness of Japan, development of a glass industry is essential. Both co- possession of technical issues by cooperation of the members, and breakdown of conventional structures of the industry are necessary. Clarification of technical issues, and cooperation of industry, academia and government is essential. The current state, promise and issues of domestic and overseas glass technology and its R and D are described. The joint target of an industrial strategy for researchers and engineers of every sector, and the approach to such target are showed from the viewpoint of the issues for Japan and preparation of common basic technology. The role of each sector for environment preparation and policy is described to achieve the target. (NEDO)

  6. FY 1999 New Sunshine Project survey research project - Survey on the long-term energy technology strategy, etc. Fundamental survey to decide on the industrial technology strategy - Technology strategy by field (Aerospace technology field - Airplane technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (koku uchu gijutsu bun'ya (kokuki gijutsu bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey/study were conducted to contribute to proposing technology strategies such as the analysis of the present state of technical competitive force and the forecast in the airplane technology field. In future airplane industry, to meet the requests/restrictions from the society in the international airplane industry in the recent years, it is predicted that technology innovation will advance centering on the following four fields: next generation airplane technology to enable the innovative cost reduction in development/production, technology to realize the substantial reduction in flight cost of airline, technology to enhance reliability for the next generation flight which meets the multi-frequency flight/increasing demand for small plane, and airplane frontier technology. Moreover, regulations especially on noise, CO2 reduction and NOx reduction are becoming very strict internationally because of the increasing concern about global environmental problems. It is urgently needed to establish technology to cope with these trends. As the comprehensive strategy, the following are considered: development of airframe under the leadership of Japan and securing of the demand, efficient arrangement and operation of large-scale experimental facilities, IT adoption to the airplane industry, organic cooperation by industry/university/government, etc. (NEDO)

  7. Energies; Energies

    Energy Technology Data Exchange (ETDEWEB)

    Cotard, E.

    2002-02-01

    A review is made about the consequences of the European directive on energy that entered into application in august 2000. It appears that most countries are opening their electricity and gas markets at a faster pace than required by the E.U. directive. European gas imports reached 480 Gm{sup 3} in 2000 and are expected to be over 700 Gm{sup 3} in 2015, so the question of the reliability of the gas suppliers has to be answered at the European level. The current time is marked by an increase of the complexity of the energy market that is due to different factors: 1) the delay in the implementation of European energy directives in France, 2) new arrangement is occurring in United-Kingdom in the energy sector, 3) the lack of a regulating authority in Germany, and 4) the difficulty of inter-connecting the different European energy networks. This transitory period may generate some economic imbalances and competition disturbances by allowing some enterprises to benefit from lower energy prices before others. (A.C.)

  8. Fiscal 1999 research report. Japan-U.S. comparative research on energy technology transfer and innovative industry support; 1999 nendo energy gijutsu wo chushinto shita gijutsu iten oyobi shinki sangyo ikusei no Nichibei hikaku ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Japan-U.S. comparative research was made on technology transfer and innovative industry support. The U.S. industry is greatly benefited by universities, which is consequently strengthening the international competitiveness of the U.S. economy. However, the partnerships between private firms and universities have no fixed pattern, and keep changing dynamically. Business incubators increased to 627 rapidly, and mainly supported by municipal governments and universities. The U.S. has a well-established mechanism of technology transfer, and has succeeded in many cases. Not only universities but also national laboratories commit to technology transfer to venture businesses, and after starting businesses, entrepreneurs can use various hedging systems which are expected to play a role promoting the future technology innovation. The U.S. also has many advanced areas for sustainable technology innovation, like Silicon Valley, and these areas contain many supporting bodies to help new businesses. The activity of these bodies is very suggestive to Japanese local platforms promoting technology innovation and new local industry creation. Study was also made on the possibility of technology exchanges with overseas advanced areas. (NEDO)

  9. Achievement report for fiscal 1998 on the research and development of genome informatics technology. Development of energy use rationalization technologies; 1998 nendo genome informatics gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the field of the analysis of gene expression frequency information, a novel glass coating method and a highly sensitive high-speed reading device are developed. Element technologies are studied for the development of a detection system capable of high-density high-speed reading of high-density DNA capillary array, with a long-chain DNA probe solidified therein. In the technology of transcription control information analysis, concerning the technology of transcription dynamics analysis using tagged transcription control factors, the construction of a model system protocol is studied, an automatic analysis system is developed, and an evaluation technology is also developed. Furthermore, a novel method is proposed, in which two specimens will be prepared, that is, a microbead coupled DNA specimen consisting of base sequences of all combinations of a certain chain length and a cDNA (complementary deoxyribonucleic acid) derived protein specimen, and DNA-protein complexes will be isolated for analysis bead by bead out of a liquid which is a mixture of the said two specimens. (NEDO)

  10. FY 1999 report on the results of the R and D of genom informatics technology. Development of technology for rationalization of energy use; 1999 nendo genom informatics gijutsu kenkyu kaihtsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In this R and D, studies were made on the following: 1) development of a circular-shaped DNA-chip (DNA disk) and analysis of the gene expression pattern network by the DNA disk; 2) analytical system with DNA capillary array for mRNA expression profile; 3) development of protein probe technique for isolation of transcription factor complexes, and of evaluation technique for functions of transcription factors and their target DNAs; 4) transcription control information analytical technology - study of detection operational technology and preparation technology of transcription control information analytical specimens; 5) general R and D issues. In 1), development is conducted of DNA chips and a DNA chip system which makes use of DNA chips. In 2), development is made of a DNA capillary array and its accurate and high-speed reader to analyze expression profile of mRNA in various pathological processes of diseases of unknown etiology. In 3), as development of genom informatics technology, analysis of correlations is made, paying attention to transcription factors which become the key to gene expression. In 4), study is carried out of gene transcription control information high speed screening technology. (NEDO)

  11. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 4. Development of hydrogen production technology; Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 4. Suiso seizo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This paper describes development of hydrogen production technology as a part of the WE-NET project. For the solid polymer water electrolysis method higher in efficiency and lower in cost than the previous methods, 5 companies have developed element technologies for improving electrolysis cells and synthesis technologies of hot solid polymer electrolyte based on each proper catalyst electrode production method. In fiscal 1996, the initial study on large-scale systems by middle laboratory cells was made as well as improvement of electrolysis performance by small laboratory cells and endurance tests. Among the previous methods such as a hot press method (bonding of an ion exchange membrane to an electrode), an electroless plating method (preparation of porous surface onto a membrane electrode assembly), a zero gap method (preparation of high-efficiency high-current density cells), and a sintered porous electrode method (carrying of the mixture of catalytic powder and ion exchange resin-dissipated solution onto sintered metallic porous electrode surface), the former two methods were adopted for development of bench-scale cells as effective promising methods. 192 refs., 183 figs., 108 tabs.

  12. FY 1997 R/D project of industrial and scientific technologies contracted with NEDO. Report on technology development of utilization of biological resources such as bioconsortia (development of analytical techniques of bioconsortia); 1997 nendo sangyo gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo seibutsukei nado seibutsu shigen riyo gijutsu kaihatsu (fukugo seibutsukei kaiseki gijutsu no kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Bioconsortia are microbial composites composing of more than two kinds of microorganisms with special functions. To utilize their advanced functions, some techniques have been developed for analyzing their functions and interactions, and for identification, separation and incubation of the constituent microbial groups. In FY 1997, an investigation was made on technology trends, domestic researchers, and research topics related to bioconsortia. To manage and promote the progress of research at the National Institute of Bioscience and Human-Technology where the centralized management of this project is conducted, meetings are held once a month to examine the progress at the institute, in which reports are made and discussions are held on how each research item is progressing. In addition, meetings of the committee to promote research are held every other month to consider and examine measures required for promoting the research. Re-entrustment of research has been made on two subjects, i.e., `Studies on biological significance of symbiotic microorganisms` by Prof. Ishikawa of the University of Tokyo, and `Study on the relationship between the biosynthesis of useful terpenic materials of plant origin and the differentiation of plant tissues, and their effective production by plant cell cultures` by Prof. Inoue of Gifu Pharmaceutical University. 27 refs., 13 figs., 1 tab.

  13. Fiscal 1997 report on the R and D result of industrial science and technology. R and D on super metal (R and D on innovative raw metal materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku seika hokokusho. Super metal no gijutsu kaihatsu (kakushinteki kinzoku sokei zairyo no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Study was made on the applicability of mechanical milling (MM) and mechanical alloying (MA) to Fe system alloys. Metastable austenitic stainless steels such as SUS316L and SUS304L form {alpha} phases by strain induced transformation due to MM, and are subjected to further plastic deformation. Nano-size fine structure was obtained through inverse transformation into austenite({gamma}) by heat treatment or high-temperature sintering of MM powder. Fine microduplex structure of 620nm in average crystal grain size was obtained for SUS316L. This material showed nearly 3.3 times higher 0.2% tensile proof stress, nearly 1.8 times higher tensile strength, and 35% higher elongation than conventional ingot steels. Solid solution powder of 12Cr-Mo-W ferritic steel was sintered by hot isostatic pressing (HIP) under low- temperature and ultrahigh-pressure conditions of 650degC and 588MPa. The as-HIP`ed sample and sample annealed at 800degC showed average {alpha} grain sizes of 33 and 50nm, respectively, and a strength twice as high as that of 12Cr steel. 97 refs., 60 figs., 18 tabs.

  14. Survey of the situation of technology succession. Databases of articles including in industrial technology museums; Gijutsu keisho jokyo chosa. Sangyo gijutsu hakubutsukan shuzohin D.B. hen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    To promote the succession of history of and the creative use of industrial science technologies, the paper made lists and databases of the articles of industrial technology museums and material halls in Japan. Record/preservation and collection/systematization of history of the industrial technology is useful for forming bases necessary for promotion of future research/development and international contribution. Museums and material halls are the fields for making comprehensive and practical activities. The data were made as one of the basic databases as the first step for promoting activities for examining the technical succession situation in a long term range continuously and systematically. In the classification of the data, the energy relation was divided into electric power, nuclear power, oil, coal, gas and energy in general. Others were classified into metal/mine, electricity/electronics/communication, chemistry/food, ship building/heavy machinery, printing/precision instrument, and textile/spinning. Moreover, the traffic relation was classified into railroad, automobiles/two-wheeled vehicles, airline/space, and ships. Items were also set of life relation, civil engineering/architecture, and general. The total number of the museums for the survey reached 208.

  15. Fiscal 2000 achievement report. Research and development of fast-acting innovative energy-environment technology (Development of fast-acting high-efficiency solar cell technology - Development of high-quality ingot manufacturing technology); 2000 nendo shin energy sangyo gijutsu sogo kaihatsu kiko itaku kenkyu gyomu seika hokokusho. Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu (Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu - Kohinshitsu ingot seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research and development was conducted of a technology for manufacturing an ultrathin polycrystalline silicon solar cell capable of efficiency enhancement and cost reduction earlier than the types of polycrystalline solar cells now available on the market. In this fiscal year, a silicon melt/solidification experimenting apparatus was built for manufacturing high-quality silicon ingots. Using an apparatus with its performance similar to the newly built one, a preliminary experiment was conducted involving high-purity silicon ingot manufacturing. In the experiment, boron was added to 75 kg of silicon for semiconductor devices so that its resistivity may be 0.5 ohm-cm. The silicon was melted in a quartz mold, and then subjected to unidirectional coagulation at 0.13 mm/min that started at the bottom to proceed upward. The result was a silicon ingot 44 cm times 44 cm times 17 cm (height). The ingot thus obtained exhibited 0.4-0.8 ohm-cm in resistivity distribution. Solar cells produced from the ingot showed a conversion rate of 16.9%. (NEDO)

  16. FY 2000 report on the survey of the calculation of the overall conversion efficiency in case of using natural gas for fuel cells, etc.; 2000 nendo chosa hokokusho. Tennengas wo nenryodenchi ni mochiita baai no sogo henkan koritsu no santei ni kansuru chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For the purpose of evaluating the efficiency of fuel cell including the fuel supply system, survey was made of drilling of gas resource, conversion to liquid base fuel, transportation, storage, etc., the energy conversion efficiency was studied considering reforming characteristics of various fuels. In the comparison between LNG, methanol, DME and GTL that originate in natural gas and LPG and naphtha that originate in oil, a big difference is that methanol, DME and GTL were made through the conversion process with the large energy consumption. Namely, by the time before the reforming into hydrogen, the oil base indicated a higher efficiency in secondary energy fuel production than the natural gas base. Further, the reforming efficiency is the highest in methanol and DME, and there is a little difference between the integrated fuel cell (normal pressure) and the hydrogen production use fuel cell (pressurized). Concerning city gas and GTL, the efficiency is lower, affected by S/C. The overall efficiency is determined considering the conversion efficiency in other stages since it is determined by the conversion efficiency of up to the raw fuel and the energy conversion efficiency at PEFC. (NEDO)

  17. Intelligent social infrastructure technology. Infrastructure technology support ultra-reliable society; Chiteki shakai kiban kogaku gijutsu. Choanshin shakai wo sasaeru kiban gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    This survey was conducted to construct the core of intelligent social infrastructure technology (ISIT), and to investigate its practical application to industries and society. For realizing the ultra-safe and ultra-reliable society, it is necessary to develop the ISIT which can integrate various social infrastructures, such as architecture, city, energy, and lifeline systems required for living. For the systematization of cities, it is necessary to process and control the intelligent information by holding integrated and transverse information in common, as to logistics, lifeline, communication, monitoring, and control. For the communication engineering, the centralized systems are acceleratingly to be converted into the distributed network systems. For the mechanical engineering, intelligent control and robot technology are required. For the architectural engineering, a concept exceeding the conventional antiseismic structure idea is investigated. It is necessary to develop a new information technology providing an intelligent social infrastructures by merging the information networks and the physical world seamlessly. Necessity of ISIT is large for constructing the intelligent and ultra-reliable society consisting of these integrated and organized networks. 84 refs., 68 figs., 6 tabs.

  18. FY 1999 Report on research and development of energy utilization rationalization superhigh-technological liquid crystal technologies. Superhigh-technological electronic technology development promotion project for new functional electronic material design, control and analysis technologies; 1999 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-04-01

    Described herein are the FY 1999 results of the liquid crystal technology development project. For the researches on multi-layer reflection, composite panels of flattened resins of different refractive index are developed to improve 2-layer monochromic contrast ratio. The guest/host liquid crystal compositions of high orientation order are investigated as the those useful for high contrast. Compounds are pursued for superanisotropic light absorption, and modification with a substituent is found to be effective. Molecular orientation controlling is also studied. For researches on memory-sustaining type liquid crystals, the studied items include formation of thin ferroelectric films on glass substrates, improvement of voltage-sustaining characteristics by composites (including compounds), and doping of trace quantities of ionic impurities. For development of image element colors, the studied items include multi-lattice-structured, oriented HPDLC devices, composites of high birefringence (high order light scattering), and light interference, high order light scattering type light control devices. The multi-dimensionally anisotropic structure of configuration divided into 3 parts of R, G and B is developed to create directive reflection which improves brightness of the reflection type color liquid crystal. A group of compounds are pursued to develop liquid crystal compositions of high refractive index anisotropy, and promising ones are found. The results of the comprehensive investigations are also described. (NEDO)

  19. Fiscal 2000 research achievement report on the development of super-advanced liquid crystal technology for energy use rationalization. Development promotion project for super-advanced electronic technology - Design, control, analysis, etc., of electronic materials having novel functions; 2000 nendo energy shiyo gorika chosentan ekisho gijutsu kaihatsu seika hokokusho. Chosentan denshi gijutsu kaihatsu sokushin jigyo (shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-04-01

    Efforts are focused on the verification of target devices under the respective subjects, and activities are conducted with the development system reinforced. Three newly proposed reflection type liquid crystal devices achieve the target specifications of a reflection factor of 60% or higher and a contrast ratio of 15:1 or higher. Studies are conducted involving the five fields of (1) multilayer reflection devices, (2) memory retention liquid crystal devices, (3) single pixel color devices, (4) directional reflection devices, and (5) joint research. Research and development in field (1) covers ultra-anisotropic optical materials, ultrahigh reliability host liquid crystal materials for guest-host liquid crystals - mixed system, low voltage driven/high load holding liquid crystal compound systems, and new liquid crystal molecule orientation control technology; in field (2), low temperature fabrication of ferroelectric thin film, and ultrahigh purity high reliability liquid crystal compounds; in field (3), materials capable of controlling optical interference and higher order light scattering, photoregulation devices, highly birefringent liquid crystal materials - mixed system, and ultrahigh efficiency light scattering liquid crystal compounds; and, in field (4), multi-dimensional anisotropic structure fabrication technology and ultra-anisotropic optical materials. (NEDO)

  20. FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on technology innovation indices to be worked out; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (gijutsu kakushin shihyo no sakutei ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For technology innovation, it is indispensable to arrange the environment where the continuous and spontaneous technology innovations are generated. >From this point of view, the paper re-confirmed functions of enterprises, universities and national research institutes that are main bodies of technology innovation. For the use for working out measures for activation as the basic data, conducted were the making of indices for surveying the whole system of technology innovation in Japan, and the study of the data to be prepared as statistics and the survey method. In the 1st stage, about 450 figure/table data related to technology innovation were collected for making them database from official statistic data and publications of governments and international organizations in Japan and European countries. Further, using official statistic data, about 240 figure/tables were made which seem to be important as indices of technology innovation. In the 2nd stage, on the basis of this database, the details of the activities were analyzed, and from the indices, the actual situation/subjects were considered. At last, the paper explained the index system of 'Oslo Manual' which is a guideline of working out OECD's innovation indices. (NEDO)

  1. FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on technology innovation indices to be worked out; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (gijutsu kakushin shihyo no sakutei ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For technology innovation, it is indispensable to arrange the environment where the continuous and spontaneous technology innovations are generated. >From this point of view, the paper re-confirmed functions of enterprises, universities and national research institutes that are main bodies of technology innovation. For the use for working out measures for activation as the basic data, conducted were the making of indices for surveying the whole system of technology innovation in Japan, and the study of the data to be prepared as statistics and the survey method. In the 1st stage, about 450 figure/table data related to technology innovation were collected for making them database from official statistic data and publications of governments and international organizations in Japan and European countries. Further, using official statistic data, about 240 figure/tables were made which seem to be important as indices of technology innovation. In the 2nd stage, on the basis of this database, the details of the activities were analyzed, and from the indices, the actual situation/subjects were considered. At last, the paper explained the index system of 'Oslo Manual' which is a guideline of working out OECD's innovation indices. (NEDO)

  2. FY 1998 research result report. Ultra-high liquid crystal technology development for energy use rationalization (Technology of design/control/analysis of new functional electronic materials of the ultra-high electronic technology development promotion project); 1998 nendo kenkyu seika hokokusho. Energy shiyo gorika chosentan ekisho gijutsu kaihatsu (chosentan denshi gijutsu kaihatsu sokushin jigyo shinkino denshi zairyo sekkei seigyo bunseki nado gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-05-01

    Element technology is studied to realize a reflective-type, full-color, and high-resolution liquid crystal display for super-low power consumption data display. As to the functional compound microstructure formation technology, a 4-inch panel was trially fabricated using two-layer guest-host liquid crystal technology to achieve the desired display performance by control of molecular orientation. Further, holographic PDLC elements were favorably test-fabricated. A ferroelectric PZT thin layer was formed by forming layer at low temperature at which a glass substrate can be used. Optical interference/optical dispersion type optical control materials were studied by liquid crystal/polymer composition. Also studied were super-pure/super-reliable liquid crystal compound/liquid crystal composite systems and super-anisotropic liquid crystal compound by modeling ionic impurities and liquid crystal molecular interaction. In relation to the control technology of optical reflection characteristics, effects of liquid crystal molecular structures (derivative effect and copolymer composition) on orientation were elucidated. As to the technology to form multi-dimensional anisotropic structures, efforts were made for the heightening of formation technology of simple RGB (red, green, blue) directional reflection layers using acrylate materials. The paper also outlined the comprehensive survey. (NEDO)

  3. Fiscal 1997 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1997 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `Chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level, the R and D was conducted of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology, ultra high accuracy shading system technology, ultra high tech plasma reactive measuring/analysis/control technology, ultra high tech cleaning basic technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. This R and D is a greatly influential basic research in the whole industrial field, and therefore, it is necessary that researchers standing foremost in each field of industry/university/government join the project and that various R and D infrastructures are made the most of. For this, the concentrated joint research method and the dispersed joint research method are combined, and the R and D is being conduced by equal partnership of each researcher. 421 refs., 823 figs., 91 tabs.

  4. Fiscal 1996 survey report. `Ultra high electronic technology development promotion project` under consignment from NEDO; 1996 nendo kenkyu seika hokokusho. Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku jigyo `chosentan denshi gijutsu kaihatsu sokushin jigyo`

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    For the purpose of establishing ultra high technology of a next next generation level which is a basic technology in the electronic information field, a key to the realization of the high grade information society and a common technology base giving marked influences to the wide range industrial field, the R and D was started of ultra fine processing process technology, technologies on limit measuring/analysis/control and new functional electronic materials. Themes of the R and D are electronic beam direct picture drawing system technology, ultra short wavelength electromagnetic radiation patterning/system technology, ultra fine sensitizing technology to draw pictures on metal and crystal surfaces using ultra short wavelength laser beams, shading system technology of shading mask to be used to the process of drawing ultra high accuracy and complicated figures, ultra high tech plasma reactive measuring/analysis/control technologies which become the base of ultra thin films and ultra fine etching using plasma, ultra high tech cleaning base technology, ultra high sensitivity medium technology, new functional element/film formation technology, etc. 137 refs., 358 figs., 38 tabs.

  5. Overview of FY1997 human media technology R and D; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu seido Shin energy Sangyo Gijutsu sogo Kaihatsu Kiko itaku jigyo. Human media no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports a summary of results in fiscal 1997 of research and development of human media technology. Fiscal 1997 launched design and trial fabrication of the following items: interface to improve efficiency and safety of plant operators, accommodation of multimedia contents to aid Kansei design, city development design aiding technologies using contents retrieval and presentation technologies and virtual reality, and empirical evaluation technologies for safety, comfort and convenience. Specific study assignments were extracted on a virtual media technology, a Kansei media technology and a knowledge media technology being three elementary technologies for human media to make clear the research and development approaches to be taken in the coming fiscal years. In addition, a human media technology committee, a research and development working group, and an investigation working group were established. Also launched were investigations on research trends in the human media technology, and investigative researches on contacts of information needs in industries with human media. 59 refs., 114 figs., 24 tabs.

  6. Survey for making a data book on the new energy technological development (photovoltaic power generation); Shin energy gijutsu kaihatsu kankei data shu sakusei chosa (taiyoko hatsuden)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    Data on the photovoltaic power generation are synthetically collected, systematized, and summarized as a data book on the photovoltaic power system. Main details are as follows: photovoltaic power systems were listed by usage, by size of power generation, and by authority concerned. Significance of adopting the photovoltaic system is stated at each level of each user of the country, local governments and individuals. As to the present situation of the solar cell market, solar cells were arranged in terms of production volume by region, production volume by type, production volume by company, shipment by usage, production amount, and price. With regard to policies of each country on the photovoltaic power system, those of advanced countries including Japan were summed up. Concerning the introduction of the system in each country, examples of the introduction were made clear, and at the same time the estimated volume of and the target for introduction of the photovoltaic power system were summarized. In respect to the subsidy system for the introduction of the photovoltaic power system, arranged were the subsidy system, the preferential tax system and the loan system.

  7. Investigation on preparing data collections related to new energy technology development. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    With an objective to put data related to fuel cells systematically into order, related data were collected comprehensively. Reviewing large international conferences impresses dawn of commercialization in phosphoric acid fuel cells (PAFC), take-off of megawatt-class molten carbonate fuel cells (MCFC), and remarkable advancement in studies on solid oxide fuel cells (SOFC) and polymer electrolyte fuel cells (PEFC). The data collection may be compiled as follows: basic principles, features, operation principles, system configurations, utilization fields, and characteristics were summarized on fuel cell power generation systems using phosphoric acid, polymer, molten carbonate, solid oxide, and alkaline fuel cells; major installation examples in Japan and overseas countries were summarized; investigations were given on developing other fuel cells such as alkaline type and direct methanol type fuel cells; and marketability, subsidies operations in Japan, and states of policy implementation in the U.S.A. were investigated and put into order. 22 refs., 24 figs., 21 tabs.

  8. Data book on new energy technology development in FY 1997. Fuel cells; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Nenryo denchi

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The purpose of this survey is to grasp the trends of technology development of fuel cells and their market, and to provide data required for supporting the introduction and diffusion of fuel cells. This report consists of Part 1 titled as `Trends of development of fuel cells in FY 1997`, and Part 2 titled as `Compiled data`. The Part 1 consists of three chapters, i.e., Chapter 1 titled as `Introduction`, Chapter 2 as `Development trends of fuel cells for on-site power generation`, and Chapter 3 as `Trends of development of fuel cells for mobile objects and fuel cell-powered vehicles`. The introductory chapter not only outlines the development trends but also describes the results of the 5th Grove Fuel Cell Symposium noticed as the major global international symposium on fuel cell in general and the environmental problems discussed at the COP3 Kyoto Conference, both held in TY 1997. The Part 2 contains the principles, system configurations and applications of fuel cells, PAFC, MCFC, SOFC, PEFC, modifier, DMFC, development trend of fuel cell-powered vehicles, and national policies for fuel cells in Japan. The Appendix features a report of the new technique investigation working group and information on fuel cells from newspapers. 100 refs., 4 figs.

  9. Data book on new energy technology development in FY 1997. Installations of photovoltaic (PV) power generation; Shin energy gijutsu kaihatsu kankei data shu sakusei chosa. Taiyoko hatsuden jireishu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The present survey places particular emphasis on the field of PV power generation systems, and intends to collect data on solar cell application products and PV power generation system installation cases, to classify them according to their usage and to compile a collection of case records including photographs. For the data collection, two formats have been adopted. A format for the solar cell-based products includes a picture of the product, and information on solar cell output and commercialization status. Another format for the installation of PV power systems includes a picture of the installation, and information on location, output level, system type, PV module type, owner, and date of installation. The application of solar cells was classified into 14 fields, i.e., consumer appliances, road and traffic, railroad, general industries, housing related, automobiles, agriculture, ocean development, disaster prevention and safety, amenity, developing countries, buildings, public facilities, and environment. A total of 241 valid cases have been collected. Overseas products and installation cases are often characterized by new applications and innovative design, and contain a lot of useful suggestions for promoting the spread of PV technology in Japan

  10. Electron attachment coefficient in low E/N regions and a discussion of discharge-instability in KrF laser. ; Analysis by logarithm transformed Boltzmann equation. Tei E/N ryoiki no denshi fuchaku keisu to KrF laser reiki hoden no fuanteisei ni kansuru ichi kosatsu. ; Tai su henkan Boltzmann hoteishiki ni yoru kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Kawakami, H.; Urabe, J.; Yukimura, K. (Doshisha Univ., Kyoto (Japan))

    1991-03-20

    In a discharge excitation rare gas halide excima laser, uniform generation and stable maintenance of the excited discharge determines the laser characteristics. In this report, an approximate solution was obtained on the Boltzmann equation (frequently used for the theoretical analysis of this laser) to examine the nature of the solution. By optimizing the conversion of the variables, calculation of an electron swarm parameter in the hitherto uncertain range of the low conversion electric field was made possible, giving a generation mechanism of the uncertainty of the excited dischareg. The results are summarized as below. (1) The Boltzmann equation gives a linear solution for a logarithmic value of an electron energy in the range of low conversion electric field. (2) Time-wise responce ability between the measured voltage, current characteristics of the excitation discharge was clarified and the attachment and ionization coefficients calculated by Boltzmann equation. (3) Dependency of the attachment coefficient on the partial pressure of fluorine and kripton was examined, and the attachment coefficient was found to increase with the increase of the partial pressure for the both cases. 20 refs., 9 figs., 2 tabs.

  11. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Electronic information technology field (Human process ware field for computers); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chsao hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) denshi joho gijutsu bun'ya (computer kanren bun'ya no uchi, human process wear bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a human process ware (HPW) field on electronic information. Although the current HPW industry is not yet complete, various technologies concerned are being stored, and the HPW industry is expected as new major industry for home and personal information equipment. As factors hindering technological innovation in Japan, the incomplete market, poor cooperation between industry and government, ambiguous role of university, and poor standardization were pointed out. Technology trends were analyzed to extract seed technology fields from 3 viewpoints of mobile HPW available at any time, at any place and to anybody, HPW system capable of customizing every personal use, and HPW supporting development of a creativity. As general strategy, the technology seed chart and map of technical development targets for every HPW were prepared to conceive a route to practical use, and develop element technologies required for practical use, based on the future trend of the market. (NEDO)

  12. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Electronic information technology field (Human process ware field for computers); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chsao hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) denshi joho gijutsu bun'ya (computer kanren bun'ya no uchi, human process wear bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 basic research result on industrial technology strategy of a human process ware (HPW) field on electronic information. Although the current HPW industry is not yet complete, various technologies concerned are being stored, and the HPW industry is expected as new major industry for home and personal information equipment. As factors hindering technological innovation in Japan, the incomplete market, poor cooperation between industry and government, ambiguous role of university, and poor standardization were pointed out. Technology trends were analyzed to extract seed technology fields from 3 viewpoints of mobile HPW available at any time, at any place and to anybody, HPW system capable of customizing every personal use, and HPW supporting development of a creativity. As general strategy, the technology seed chart and map of technical development targets for every HPW were prepared to conceive a route to practical use, and develop element technologies required for practical use, based on the future trend of the market. (NEDO)

  13. Report on achievements in fiscal 1999. Research and development of immediately effective and innovative energy environment technology (Development of immediately effective and high-efficiency solar cell technology, development of high-quality ingot manufacturing technology, and development of high-efficiency cell making technology); 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (kohinshitsu ingot seizo gijutsu kaihatsu / kohinshitsu cell ka gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been made on improving quality of ingots for substrates, manufacturing high-quality thin type substrates, and making high-efficiency cells. This paper summarizes the achievements in fiscal 1999. In developing the high-quality ingot manufacturing technology, discussions were given on a method for assessing impurities and crystal defects by using the total reflection scattering type infrared tomography, and on the optimal solidifying and cooling conditions during the ingot manufacturing by using simulation calculation for solidification. As a result of analyses and discussions, such findings were found effective that the ingot should be solidified through making the solid-liquid interface shape flat, and the temperature falling rate in an ingot should be maintained constant. In developing the high-efficiency cell making technology, discussions were given on the optimal construction based on a simulation that assumes the light sealing structure using the RIE method, and on the optimal construction of polycrystalline silicon solar cells by using a device simulator (PCID). The important factors in achieving a conversion efficiency of 20% are the light sealing structure, surface passivation, and substrate thickness. (NEDO)

  14. FY 1999 New Sunshine Project survey research project - Survey on the long-term energy technology strategy, etc. Fundamental survey to decide on the industrial technology strategy - Technology strategy by field (Fiber technology field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (sen'i gijutsu bun'ya))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey/study were conducted to contribute to proposing technology strategies such as the analysis of the present state of technical competitive force and the forecast in the fiber industry technology field. For the fiber industry to meet the requests from the society in the 21st century and to develop as an industry, it is necessary to achieve the technology innovation by making use of technology and recreation. As important seeds for which the Japanese fiber industry should focus efforts, the following were cited: To double the strength of general-purpose polymer synthetic fiber; To add the environmental control function by gradient functionalization; To practically use the environmental harmony type nonaqueous working process; To develop the fiber environmentally friendly and fiber working process; To give sensor functions such as temperature-humidity sensitive function; To develop petroleum substituting fiber materials; To develop separation/decomposition technology and reproduction technology of composite materials; etc. Further, in the recreation field, the paper cited the arrangement of intellectual property protection/design property preservation, and the promotion of commercial base making and strengthening of life style proposals. (NEDO)

  15. FY 1999 New Sunshine Project survey research project - Survey on the long-term energy technology strategy, etc. Fundamental survey to decide on the industrial technology strategy - Technology strategy by field (Material technology field - Nonferrous metal field); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku (zairyo gijutsu bun'ya (hitetsu kinzoku bun'ya)))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The survey/study were conducted to contribute to proposing technology strategies such as technical competitive force and the forecast in the material field, especially in the silicon wafer and compound semiconductor field. As to the silicon wafer technology, the following technologies were pointed out as those to be reinforced: future silicon crystals, mirror processing wafer, breakthrough technology needed for super LSI, heat-treated wafer, epitaxial wafer, SOI wafer, measuring/assessment technology, etc. In relation to the compound semiconductor technology, survey/study were made on the bulk crystal growth technology, epitaxial growth technology, crystal growth device technology, wafer processing technology, inspection/evaluation technology, device processing technology, etc. As the comprehensive strategy, the following were proposed: establishment of the place for industry/government/university cooperation, establishment of the center for evaluation of wafer materials/characteristics/process, and establishment of the compound semiconductor R and D center where men of practical business ability from industry/government/university get together and conduct the R and D of production technology and production facilities for compound semiconductor materials and devices. (NEDO)

  16. Survey of technological trends in functional membrane materials; Kinosei makuzai ni kansuru gijutsu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1979-03-01

    Materials for membranes with novel functions are surveyed. The survey is focused on 10 subjects, which are high-performance RO (reverse osmosis)/UF (ultrafiltration) membranes; development of an energy-efficient secondary treatment system for urban wastewater using pollution-free membranes; high-performance ion exchange membranes; artificial lung membranes; hydrogen separation membranes (hydrogen as energy); development of an energy-efficient combustion system using gas separation membranes (oxygen-enriched membranes); organic matter separation membranes; enzyme-aided chemical reaction membranes and their application; development of a distilling ship; and functional membranes making use of photosynthesis. Discussed in this connection are the outlines of the technologies, the need of their development, methods and contents of the development efforts, and the effects and impacts of their development. The survey further concerns the particulars of the trends in novel technologies about functional membrane materials development, covering gas separation and liquid separation technologies; chemical reaction membranes; and enzyme-aided chemical reaction membranes and their application systems. As for their application, the survey covers the field of application of desalinated or ultrapure water; field of application of food fermentation technologies; industrial wastewater, valuable materials recovery, and urban wastewater treatment; and application to medical systems. (NEDO)

  17. Present status and prospect of the pneumatics; Kukiatsu gijutsu no ayumi to kongono kenkyu no kadai

    Energy Technology Data Exchange (ETDEWEB)

    Kawai, S. [Waseda University, Tokyo (Japan). School of Science and Engineering

    2000-05-15

    This paper describes course of pneumatic technologies and problems in future researches. Pneumatic systems are inferior to electric and hydraulic systems in terms of efficiency. It is because electric power is converted into fluidized energy by using a compressor, and then converted to mechanical energy by using an actuator. When theses published from 1990 through 1999 are put in order, the research objects are accounted for half by control related technologies, and researches related to elements account for only one third. This paper enumerates assignments to be tackled positively in the future by utilizing compressibility of air in pneumatic systems, and features of high speed drive utilizing the stored energy instantaneously. Application of air pressure to robotics from the demand of the aging society, and pneumatic tools having intelligent functions must be subjected to new contrivances. These will serve for work assistance systems to enable aged people to perform works, and for activating industries including organic agriculture. Tools in this sense may include impact wrench, and others. Furthermore, development of fundamental studies for 'why air pressure?' is demanded strongly, including the viewpoint of LCA in the recycling type society. (NEDO)

  18. Investigation into the situation of technology succession; Gijutsu keisho jokyo chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1996-03-01

    The paper made a fundamental investigation to promote historical succession and creative use of the industrial scientific technology. As for the wind power generation, the large-scaling became centralized wind power plants, and the downsizing became the distribution to remote areas. The solar power generation shifted from the thermal power generation to the light power generation. There is also a method to use solar heat directly. As to power systems and the distribution of electric power, the subjects are a combination of energy source, geographical energy transportation, and heightening of consumption efficiency. It was indicated that the subjects changed with a lapse of time under technical/social/systematical conditions, and under the developable energy amount prescribed by those conditions. Heightening of efficiency, which can be realized even by a paper simulation, was realized partly helped by the developing measuring technology. The environmental problem becomes historically severe as a condition of the technical development. However, aimed at was the process where discharged matters and by-products are effectively used and disused matters are not produced. In the coal-thermal power generation, for example, a load of flue gas purification was reduced by the conversion to LNG. 253 refs., 65 figs., 12 tabs.

  19. Transportation Energy - Sandia Energy

    Science.gov (United States)

    Energy Energy Secure & Sustainable Energy Future Search Icon Sandia Home Locations Contact Us Employee Locator Menu Stationary Power solar Energy Conversion Efficiency Increasing the amount of electricity produced from a given thermal energy input. Solar Energy Wind Energy Water Power Supercritical CO2

  20. Energy Research - Sandia Energy

    Science.gov (United States)

    Energy Energy Secure & Sustainable Energy Future Search Icon Sandia Home Locations Contact Us Employee Locator Menu Stationary Power solar Energy Conversion Efficiency Increasing the amount of electricity produced from a given thermal energy input. Solar Energy Wind Energy Water Power Supercritical CO2

  1. Leading research on next generation metal production technology; Jisedai kinzoku shigen seisan gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The energy saving environment-friendly technology for low- grade difficult-to-process ores was researched focusing attention on the hydro-metallurgical process of non-ferrous metals. This research aims at development of both effective leaching system of metals, and separation/crystallization system recognizing the property difference between metal ions in solution. The leaching system allows the inexpensive molecular level control of electron transfer, mass transfer of metal ions and stabilization of leached metal ions in a solid/liquid interface. The system thus allows selective leaching of metals from various resources such as difficult- to-leach sulfide minerals to prepare concentrated solutions. The separation system can obtain high-purity solutions including each metal ion by advanced separation/concentration technology from the solutions. The crystallization technology (including electrolysis) is developed for preparing target metal materials by molecular level control of nucleation, particle growth, thin film formation and bulky metal formation processes. Overall energy consumption is reduced to 1/3 of that of the pyro-metallurgical method, aiming at zero emission. 15 refs., 14 figs., 11 tabs.

  2. Leading research on cell proliferation regulation technology; Saibo zoshoku seigyo gijutsu no sendo kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    For developing intelligent material, animal test alternative model, bio-cell analysis equipment, self-controlling bio-reactor and medical material, development of functional cells was studied by cell proliferation regulation technology. In fiscal 1996, the expression analysis and separation technology of specific gene for cell proliferation, and the intracellular regulation technology were surveyed from the viewpoint of intracellular regulation. The cell proliferation regulation technology by specific regulating material of cells, extracellular matrix, coculture system and embryonic cell was surveyed from the viewpoint of extracellular regulation. In addition, based on these survey results, new cell culture/analysis technology, new bio-material, artificial organ system, energy saving bio-reactor, environment purification microorganism, and animal test alternative model were surveyed as applications to industrial basic technologies from a long-term viewpoint. The approach to cell proliferation regulation requires preparation of a concrete proliferation regulation technology system of cells, and concrete application targets. 268 refs., 43 figs., 4 tabs.

  3. Technical features of steel structure construction by Kawasaki Steel; Kawasaki Seitetsu no kokozo gijutsu no tokucho

    Energy Technology Data Exchange (ETDEWEB)

    Kaneko, T.; Urata, I.; Okata, S. [Kawasaki Steel Corp., Tokyo (Japan)

    1996-03-01

    In the steel structure technology of Kawasaki Steel, the joint technique (e.g., welding) is added to them while developing or improving the products that meet the social needs as a material supplier. Moreover, the execution technique that manufactures materials or constructs them as an integrated structure, the structural analysis that conforms to the function and application of a structure, and the design technique on dynamic properties or durability such as earthquake resistance, fatigue, and corrosion resistance are synthetically expanded for engineering. In this paper, a building steel frame, non-residence building, bridge, and harbor structure as steel structure in the building and construction fields were described for each structure genre. The structural technology of a building steel frame is summarized to the products of pillar materials. An earthquake brace, using a dead soft steel, with high earthquake energy absorption capability and a damping wall were also developed. The design and execution technique of a large roof was systematized. The exchange technique of a road bridge RC floor and the technique of an unstiffened suspension bridge for pipeline were developed. A new technique was also developed for a suspension monorail track and offshore structure. 30 refs., 5 figs.

  4. Emerging technologies for demand side management. Demand side management jitsugen no tame no saishin gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, H; Iyoda, I [Mitsubishi Electric Corp., Tokyo (Japan)

    1993-11-05

    This paper explains the latest situation in hardware technologies to realize the demand side management, divided into the following technologies: communications technology, measurement technology, client information system technology, load controlling technology, home automation technology, and energy storing and saving technologies. Speaking of the communications technology, information exchange between the supply side and the demand side is important in the demand side management, whereas a technology intended of automatic power distribution and automatic meter-reading is advancing in development. The technology covers transmissions using from power lines and telephone lines to optical cables and wireless communications. Power line communications using power transmission lines as communication lines are simple and economical, but weak against noise, and not suitable for long-distance communications. Wireless communications have been drawing attentions along with the development of mobile communication device technologies. These technologies will give benefits to electric power companies in the initial stage of their use, such as for load investigation and general automation in power distribution. They would shift to benefiting users in about 2010 covering from security information such as about power interruption to publicity information and educations. 8 refs., 8 figs., 1 tab.

  5. Laser materials processing as manufacturing technology; Seisan gijutsu to shite no laser kako

    Energy Technology Data Exchange (ETDEWEB)

    Miyamoto, I. [Osaka University, Osaka (Japan)

    1998-11-01

    This paper describes the laser material processing. Laser is artificial light that uses the amplification based on the induced emission of light. It is very excellent in directivity and monochromaticity. The high power density and concentration characteristics of laser enable a variety of high-performance processing such as junction, removal, reforming, and addition. Excellent controllability (that facilitates the automated processing), transmission performance (the processing by energy transmission in long range space is most suitable for laser), and non-contact processing (that contains no wearing, noise, and contamination) are great advantages that the existing processing method does not have. In the wide wavelength area between ultraviolet and infrared areas, the laser that can be used for material processing is very wide over the range of the continuous oscillation to the ultra short pulse of a nanosecond order. The thermal processing accompanied by melting and evaporation as well as the non-thermal processing (quantum processing) by a photochemical reaction is also available as the type of processing. The processing used for manufacturing technology is almost thermal processing including removal, junction, reforming, and addition. The thermal processing covers the range of electronics to heavy industry. 29 refs., 12 figs., 2 tabs.

  6. Development of pressurized coal partial combustor; Kaatsu sekitan bubun nenshoro gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Watanabe, T [Center for Coal Utilization, Japan, Tokyo (Japan); Kawamura, K [Kawasaki Heavy Industries, Ltd., Kobe (Japan); Tanaka, T [Chubu Electric Power Co. Inc., Nagoya (Japan); Muramatsu, T [Electric Power Development Co. Ltd., Tokyo (Japan)

    1996-09-01

    The coal partial combustor (CPC) uses a combustion technology with which coal is burned at elevated temperatures and under revolution, the constituents are captured on the furnace wall and removed as molten slag from the furnace. This is a combustion technology to reduce load of ash on subsequent devices. To generate a molten condition, it is necessary to raise the combustion temperature as high as possible (to about 1600 degC in the furnace), but this is effective for a gas turbine composite power generation system. An efficiency of higher than 45% may be expected at the power transmission terminal. As an operation on subsidy from the Agency of Natural Resources and Energy, the normal-pressure CPC technology has already been established, and a research on pressurized CPC is being progressed since fiscal 1991. The research is in progress with a schedule that elemental tests for 7 tons per day production are conducted until fiscal 1995, a 25 tons per day pilot plant will be completed by November 1997, and verification tests for long-term continuous operation will be implemented until 1998. The 7 tons per day elemental tests have identified gasification performance and slag extraction performance using five types of coal having different properties. 7 refs., 10 figs., 4 tabs.

  7. Bio-desulfurization technology in Japan; Wagakuni ni okeru baio datsuryu gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    Maruhashi, K. [Petroleum Energy Center, Tokyo (Japan)

    2000-05-01

    A bio-reaction of microbes (catalytic reaction by an enzyme) is characterized in that the reaction is carried out at a normal temperature and under a normal pressure and has particularly high specificity with respect to substrate (reactant). It is considered that a low loading process of environment harmony type can be constructed by applying the bio-reaction in petroleum refinery process. CO{sub 2} exhaust and energy consumption in the bio-desulfurization (BDS) is estimated to be 70 to 80% lower than those in hydrodesulfurization (HDS). The bio-technologies that can be applied to the petroleum refinery process include, for example, desulfurization, demetallation, dewaxing, denitration, cracking and so on. In this paper, the present state of bio-desulphurization technology is introduced. Particularly, as the research results in Japan, acquirement of mesophile R.erythropolis KA2-5-1 strain, thermophile Paenibacillus sp. A11-2 strain whose optimum temperature is 50 degrees C, BT degradation fungus Rhodococcus sp. T09 and the like are introduced. (NEDO)

  8. Application of wavelet transform to seismic data; Wavelet henkan no jishin tansa eno tekiyo

    Energy Technology Data Exchange (ETDEWEB)

    Nakagami, K; Murayama, R; Matsuoka, T [Japan National Oil Corp., Tokyo (Japan)

    1996-05-01

    Introduced herein is the use of the wavelet transform in the field of seismic exploration. Among applications so far made, there are signal filtering, break point detection, data compression, and the solution of finite differential equations in the wavelet domain. In the field of data compression in particular, some examples of practical application have been introduced already. In seismic exploration, it is expected that the wavelet transform will separate signals and noises in data in a way different from the Fourier transform. The continuous wavelet transform displays time change in frequency easy to read, but is not suitable for the analysis and processing large quantities of data. On the other hand, the discrete wavelet transform, being an orthogonal transform, can handle large quantities of data. As compared with the conventional Fourier transform that handles only the frequency domain, the wavelet transform handles the time domain as well as the frequency domain, and therefore is more convenient in handling unsteady signals. 9 ref., 8 figs.

  9. Fiscal 1996 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials; 1996 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technologies were described of creating original high-functional materials. The paper presented the following two as fields of technology on which importance is to be placed for the future R and D from technological and socioeconomic points of view. In the field of new materials of living organism imitation type, remarkably high-performance/high-functional new materials are invented by imitating the precise function manifestation mechanism of the ultimate living organism in which a great variety of matters are in harmony with each other and manifest complicated and high-level functions. In the field of structural control/synthesis process technology, the paper is aimed at manifestation of newer and higher functions/performance and innovation of the synthesis process, and also at developing technology to precisely control structure and process of materials including surface and interface in correspondence with atomic/molecular to macro levels. Up to the present, conducted were an examination of autonomous response materials (the subtheme is a R and D of polymer/composite multi-stimuli-responsive materials) and a R and D of precise polymerization (control) polymer materials. 239 refs., 129 figs., 49 tabs.

  10. Fiscal 1997 research report on the R and D project under a consignment from NEDO. Photonics engineering (R and D of photonics measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Photon keisoku kako gijutsu (photon keisoku kako gijutsu no kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Survey was made on the trend of R and D on photonics engineering to clarify the direction of its impact and ripple effect on industrial fields. Reduction of environment burden, improvement of the productivity and reliability of products, and creation of new industries by novel creative R and D are necessary simultaneously. For reconsideration of the previous measurement and machining technologies in a manufacturing industry, use of photon (laser) beams is promising. As photonics engineering, photonics measurement and machining, and elemental and peripheral technologies for generation and control of photon were surveyed. Photonics application technologies for medical care and diagnosis, communication and transmission, entertainment, and chemical fields were also surveyed. In fiscal 1997 as the first year of this project, based on the results obtained in leading researches conducted until fiscal 1996, some technological issues were clarified through the survey on the latest trend of photonics engineering in measurement, machining and generation fields, and its feasibility in the other fields. 265 refs., 91 figs., 10 tabs.

  11. Report on the results of the fiscal 1997 R and D under consignment from NEDO of photon measuring/processing technology (R and D of petroleum production system high-grade measuring/processing technology); 1997 nendo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku photon keisoku kako gijutsu (sekiyu seisan system kodo keisoku kako gijutsu kenkyu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The R and D were conducted of high-strength and high-accuracy welding/joining technology using laser, technology to measure and assess the joining state of structures and defects around the surface of structures and inside structures by high accuracy and high resolution, and technology/equipment to generate a laser light source for the tool, which are all required to remarkably enhance safety/reliability of oil drilling facilities working in the severe environment. In fiscal 1997, as the R and D of oil production system high-grade measuring/processing technology, technical study, study of measures to be taken, operating experiment, assessment, examination, etc. were conducted on the following themes: 1) macroscopic processing technology (R and D of high-reliability laser welding technology), 2) non-destructive composition measuring technology (R and D of internal measurement and photoelectron spectroscopy using short-wavelength radiation), 3) tight-focusing all-solid-state laser technology (R and D of fiber laser), 4) tight-focusing all-solid-state laser technology (R and D of high-efficiency laser diode), and 5) comprehensive investigation of phonics engineering (investigation for photon-applied materials processing technology). 256 refs., 205 figs., 18 tabs.

  12. Report on the results of research and development under a consignment from NEDO on deca-nano quantum integrating transistor substrate technologies; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Deca-nano ryoshi shusekika soshi kiban gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Researches have been conducted on deca-nano quantum integrating transistor substrate technologies, and developments were made on a three-dimensional device simulator which can be used in deca-nano domains, and a circuit simulator to have quantifying function transistors coexist with silicon semiconductor integrated circuits. The researches were intended to develop a simulator capable of analyzing properties of very small silicon and compound semiconductor devices in deca-nano domains. The researches discussed the applicability of conventional simulators, calculated quantum levels in a three-dimensional hetero structure, and resulted in development of an electron wave propagation simulator in optional two-dimensional shapes, a quantum Monte Carlo simulator, and a three-dimensional semiconductor device simulator with quantum correction. On the other hand, in order to estimate characteristics of a hybrid circuit in which single electron transistors coexist with conventional transistors such as CMOS transistors, a single electron hybrid circuit simulator was developed. The development indicated that a CMOS-SET fused memory is promising as a future LSI memory. 22 refs., 116 figs., 3 tabs.

  13. Fiscal 1999 research and verification of geothermal energy exploring technologies and the like. Development of reservoir change prediction technology (Development of modelling support technology); 1999 nendo chinetsu tansa gijutsu nado kensho chosa hokokusho (yoyaku). Choryuso hendo tansaho kaihatsu (choryuso hendo yosoku gijutsu (modeling shien gijutsu))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The aim is to develop and popularize techniques relating to geological information such as thermal history. The efforts center about the application of a now-available core fracture measuring system to developed geothermal fields and about the development of new technologies. The measuring system is applied to some core cuttings collected from five boreholes in the Akinomiya district, Akita Prefecture, and the system is used for (1) the evaluation of homogenization temperatures of inclusions in the fluid, (2) the measurement of the points of melting from ice of inclusions in the fluid, and (3) the implementation of laser Raman spectroscopy. Under item (1), it is found that the minimum homogenization temperature of quartz phenocryst in the mother rock or of low-salinity fluid inclusion in a quartz vein is near the current subsurface temperature and that subsurface and reservoir temperatures may be known by evaluating their homogenization temperature. Under item (2), it is found that the NaCl equivalent salinity is distributed in the range of 0.0 to 25wt% and that, in this connection, there is difference between a fluid in a fluid flow and a fluid spurting as thermal water in the Akinomiya district. Under item (3), CO2, N{sub 2}, and CH{sub 4} are detected in most of the boreholes. Efforts are exerted to develop a hydrothermal fluid analyzing technique using a rapid rock dating method and traces of chemical ingredients in hydrothermal minerals. (NEDO)

  14. Fiscal 1997 report on the results of the technical development of super metal under consignment from NEDO. Technology to create ferrous mesoscopic structure control materials; Super metal no gijutsu kaihatsu (tetsukei mesoscopic soshiki seigyo zairyo sosei gijutsu) seika hokokusho (1997 nendo). Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko (NEDO) itaku kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The fiscal 1997 results were reported of the project on the technical development of super metal which draws out limit performance of ferrous metal and improves the recyclability. In the study of large-strain deformation, a study was carried out with the use of large-strain deformation of more than 50% per 1 pass (strain rate: 0.7 or more) and multi-phase structure. By the crystal microstructuring technology, a level was reached where approximately 1{mu}m crystal size can be obtained. In the study of high magnetic field utilization, the course of study of the structure control and microstructuring was chosen in the preliminary experiment using the existing 8 tesla magnet, and the design and fabrication of a new 12 tesla large-diameter magnet were conducted. In the study of material structure prediction, modeling of microstructuring by recrystallization and establishment of a material predicting method of micro/multi-phase/mixed-grain structures were made the subjects. In the analysis of the mesoscopic structure, the mesoscopic analysis was made of the 0.3C-9Ni steel microstructured by the large-strain deformation thermal processing, and it was shown that the reflective electronic image measured by varying accelerating voltage gives new structural information. 111 refs., 135 figs., 35 tabs.

  15. Survey report for fiscal 1999 on internationalization of technologies for effective use of energy resources. Survey by exploration of international cooperative researches on energy-saving through advanced use of steel slag; 1999 nendo energy shigen yuko riyo gijutsu kenkyu kokusaika chosa hokokusho. Tekko slag no kodo riyo ni yoru sho energy gijutsu ni kansuru kokusai kyodo kenkyu no tansaku chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    As for the collection of sensible heat, 1/3 of blast-furnace slag is treated to the purpose at the Teesside Technology Centre, Britain, but none is collected in the latter half of tapping in case there is so much slag that cooling cannot be done in time. In the case of a large blast furnace, some measures have to be contrived because molten iron comes out of the furnace intermittently. In Germany, the heat collection rate is as low as 3%, with no effort made at heat collection. In North America, desire to develop such a technology is not strong. A visit was made to the Institute of Ocean Sciences, Canada, in relation to the concept of using steel slag as a eutrophic source for marine photo-plankton. A large-scale long-term test is under way for examining the relationship between global warming and ocean current circulation. There are possibilities that Japan will enter into the project for a joint study, for example, of heavy metal elution from slag though the test fails to name slag as the direct object of study. Not only for Canada but also for any other country who faces the sea, it may be a meaningful national policy to inject some active ingredients into the sea for an increase in living marine resources. Greece is engaged in the ocean dumping of nickel slag on an experimental basis but, in view of the purpose of the experiment, Japan will not be a participant in the project. (NEDO)

  16. Achievement report for fiscal 1981 on Sunshine Program survey and research. Joint projects on solar energy between Japan and Australia, etc. (Japan-France technological cooperation on solar energy); 1981 nendo Nichigo nado taiyo energy gijutsu kyoryoku jigyo seika hokokusho. Nichifutsu taiyo energy gijutsu kyoryoku

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    A curved-surface thermal power system just before completion is visited, located on the island of Corsica. Light is collected by a curved-surface mirror in which narrow flat-surface mirrors with their length matching the linear collector width are attached amphitheater-wise to a curved-surface foundation built of concrete, and a linear collector performs tracking along the focal line. Exchange of information and comparative study will be required concerning this system. As for passive use of heat, a flat-plate collector has reached a level of practical application at homes in the low-temperature domain. Sites related to long-term basic research and seawater desalination are also visited. As for collector in the high-temperature domain, a THEK (Thermo-Helio-Electricity Kilowatt) system which is a spherical mirror collector is on the initial stage of planning. It is important to compare various types of curved-surface systems for their merits and demerits. As for the production of solar cells for photovoltaic power generation, it is monopolized by the Photowatt Corporation, with most of the products to be exported for use as independent power sources. As for future development, the casting technique will be industrialized at the end of 1983, the ribbon type will come next, and the amorphous material will be farther in the future. The task is how to enhance technical cooperation in the future. (NEDO)

  17. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the technology of accelerated formation of bio-functions (R and D of the technology of creation of novel advanced enzymes); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Kasokugata seibutsu kino kochiku gijutsu no kenkyu kaihatsu (shingata kokino koso sosei gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D on creation technique of novel advanced enzymes. In fiscal 1997, a novel mutagenesis technique was developed to obtain more kinds of mutational genes by shuffling between clonal genes as compared with the previous homogeneous recombination. A genotype- and phenotype-linking technology was developed by expressing random motifs (peptide as components of the active site of protein) on bacteria, and by developing a single-motif protein library. Study was made on a selection system for functional molecules of catalytic activities in a gene level, and a selection system for function of signal transduction. Analysis and evaluation study on vitro experimental technology can be efficiently promoted by recognizing the fitness landscape of target protein molecules. As a result, instead of the conventional method which needs several cycles of mutation and screening of 3-4 week/cycle, an efficient method possible to obtain multiple mutants was established. Research work was also promoted by various organizations to develop an accelerated formation technology of bio-functions. 68 refs., 51 figs., 14 tabs.

  18. Fiscal 1997 project on the R and D of industrial scientific technology under consignment from NEDO. Report on the results of the R and D of technologies to invent original high-functional materials (technical development of materials to heighten efficiency of power generation facilities); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo koseinoka zairyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the fiscal 1997 results of the study of the condensation base precise structure control conducted as a technical development of materials to heighten efficiency of power generation facilities. Condensation base polymer is an important material which occupies most of the engineering plastics. The study is aimed at developing basic technologies on the molecular weight and regularity by which a remarkable improvement can be expected in performance of condensation polymerization/ring-opening polymerization polymer materials, polymerization catalyst which arbitarily controls the primary structure such as branch and end group structures, and development of the precision polymerization process. In the synthesis of ordered polymer by direct polycondensation, synthesis of ordered polyamide from asymmetric monomers is studied. In the synthesis of chemically selective polyamide by direct polymerization, polyamide with functional group is synthesized by polymerizing without protecting functional group the monomer with such functional group as causes side reaction in polymerization. In the synthesis of polyamide having the limited distribution of molecular weight, the molecular weight/distribution of polyamide are controlled by connectedly conducting polycondensation which is itself to be done successively. 91 refs., 72 figs., 43 tabs.

  19. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the ultimate manipulation technology of atoms and molecules (R and D of the formation of advanced materials for power generation environment); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Genshi bunshi kyokugen sosa gijutsu no kenkyu kaihatsu seika hokokusho (hatsuden kankyoyo kokino sozai keisei gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of the ultimate manipulation technology of atoms and molecules (atom technology). Ten nanoscale Ge islands were successfully formed in proper positions on an Si substrate surface by using mask technology of nanoscale atomic layers. Growth of less-defect ZnSe films on a GaAs(110) surface was possible under various conditions. The magnetic transfer mechanism of Mn oxide with huge reluctance was clarified. Through study on selective-area deposition of Si on plasma-oxidized ultrathin SiO2 mask layers patterned by direct electron-beam exposure and an idea of SiO2/SiNx bilayer mask, direct use of the ultrathin mask layer as insulating layer in device structure was achieved. The superior property as electron beam resist of methano- fullerene composed of fullerene C60 with side chains including oxygen was clarified. The initial oxidation process of an Si(100) surface was analyzed, and the observation result by SREM was theoretically explained. Development of a high-resolution spin polarization electron microscope was also mentioned. 48 refs., 145 figs., 20 tabs.

  20. Fiscal 1997 R and D project on industrial science and technology under a consignment from NEDO. R and D of the application technology of functional protein complex (R and D of the high-functional maintenance technology for power plants); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo gijutsu Sogo Kaihatsu Kiko itaku. Kinosei tanpakushitsu shugotai oyo gijutsu no kenkyu kaihatsu (hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    In order to develop advanced maintenance technology for power generation facilities, application technology of functional protein complexes is under investigation. On a light controllable enzymatic reaction system, construction of a light controllable bio-reactor by physico-chemical and bio- chemical techniques, and structure and functions of a photosynthetic protein complex using thermophilic cyanobacteria as material are under investigation. On a molecular mechanism for recognition and reaction of receptor proteins, structure analysis and engineering application of glutamate receptor channels of a synaptic transmission system, and basic study and material proteins for artificial structures using endocytic micromachinery, and a multi-enzyme system for synthesis of glycosphingolipids are under investigation. On a complex oxidation/reduction system by genetic engineering technique, construction of a high- efficiency stable system with functionally arranged oxidoreductase and electron transmission systems in biomembranes is in promotion. Research work was also made on molecular assemblies for a functional protein system. 166 refs., 91 figs., 9 tabs.

  1. Report on the results of research and development under a consignment from NEDO of glycoconjugate production utilizing technologies. Development of technologies to fix and effectively utilize carbon dioxide by applying glycoconjugates; 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Fukugo toshitsu seisan riyo gijutsu no kenkyu kaihatsu (fukugo toshitsu oyo nisanka tanso koteika yuko riyo gijutsu kaihatsu) seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper reports research results in fiscal 1997 for the `research and development of glycoconjugate production utilizing technologies`. In synthesizing, utilizing and remodeling technologies for glycoconjugates by means of chemical synthesis, studies were performed on developing methods to synthesize Gal {beta}1-3Gal NA(c {alpha})1-0-Serine in preparative scale, synthesizing high mannose type sugars of natural type without protection groups, and linking GlcNA or GalNAc onto partial peptide of fibroblast growth factor (FGF). In synthesizing, utilizing and remodeling technologies for glycoconjugates by using biological methods, studies were carried out, with regard to glycoconjugate synthesizing, utilizing and remodeling technologies utilizing animal cells, on identifying sugar structures of IFN-{gamma} produced from CHO cell line, and isolating CHO cell lines introduced with genes of sugar transferred enzyme GnTIV and/or GnTV. Furthermore, studies were conducted on glycoconjugate synthesizing, utilizing and remodeling technologies utilizing microorganisms, and glycoconjugate structure analyzing technologies. In addition, overall investigation was made on glycoconjugate production utilizing technologies. 113 refs., 76 figs., 18 tabs.

  2. Fiscal 1997 result of the R and D project of industrial science and technology under consignment from NEDO. R and D of creation technology of original advanced materials (R and D of creation technology of original advanced materials); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo (Shin Energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku). Dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu dokusoteki kokino zairyo sosei gijutsu no kenkyu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes R and D of creation technology of original advanced materials in the R and D project of industrial science and technology. Although new material technology is dependent on the needs of a future society, it should correspond to a global environment preservation society, information-oriented society and aging society as observed based on the present social trend, and new materials superior in hot strength, light weight, corrosion resistance, decomposability, photo-function, magnetism, conductivity, bio-copying and adaptability are demanded. This project is in promotion since fiscal 1996 to develop formation technology of high-performance advanced new materials by precise molecular control of structure and production process of organic polymers and molecular assemblies. The research started on 4 themes such as advanced stimulus-response material, precision catalytic polymerization, condensed system structure control and multi-dimensional polymer structure. The research on molecule harmonizing material was added in fiscal 1997. In fiscal 1997, the general committee discussed a progress situation and next year research plan, and surveyed an overseas technology trend. 1 fig.

  3. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells (development of technology to manufacture materials and substrates (development of technology to manufacture high-quality amorphous materials and substrates)); 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu seika hokokusho. Usumaku taiyo denchi no seizo gijutsu kaihatsu, zairyo kiban seizo gijutsu kaihatsu (kohinshitsu amorphous kei zairyo kiban no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    These technological developments are intended to develop technologies to manufacture with improved quality the silicon-based thin film solar cells. In order to analyze manufacturing conditions for micro crystal silicon thin films as the narrow-gap amorphous silicon-based films, films were manufactured in the vicinity of borders of amorphous/micro crystal silicon film manufacturing conditions. The present film manufacturing did not present effects of suppressing deterioration of hydrogen diluted light. In order to elucidate the light deterioration mechanism in hydrogenated amorphous silicon films and study the suppression thereof, discussions were given on impurities in the film, including oxygen. By using an ultra high vacuum plasma CVD having a thoroughgoing baking system, an oil-free exhaust mechanism, and a raw material gas refining mechanism, impurities were added to and removed from a reaction vessel, and an ultra-high purity Si:H film was manufactured, which has been removed of impurities from the raw material gas, resulting in reduction of O, C and N standing no comparison. According to the result of a light irradiation experiment on an ultra-high purity film obtained under an accelerated deteriorating condition by using a pulse laser, the model assuming the light induced defect and the pair of impure atoms has been denied. (NEDO)

  4. Energy and energy policy

    International Nuclear Information System (INIS)

    Clerici, A.

    2007-01-01

    Energy has taken with his reflections on the environment, the geopolitical aspects and its pervasive use in all activities a crucial role for sustainable development of our planet. The energy in the future will be increasingly a global problem [it

  5. Achievement report for fiscal 1981 on New Energy and Industrial Technology Development Organization-entrusted projects. Solar energy technology research and development; solar panel experiment, manufacture, and verification (Photovoltaic power system practical application technology; ribbon-type crystal substrate process technology); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (ribon kessho kiban kotei no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    Carried over from the preceding fiscal year are the development of ribbon crystal pulling technology and the studies of ribbon crystal substrate quality and plant operation. In the development of ribbon crystal pulling process, a pulling drive is built and the limiter mechanism is strengthened for improvement on ribbon crystal flatness, technologies are established for high-speed pulling of broad ribbon crystals, pulling system prototype is built, after-annealing technique is improved for eliminating distortion, and technologies are developed for continuous feeding of raw materials. In the quality examination of ribbon crystal substrates, a method is tested and studied for bringing about a decrease in the number of SiC grains. The object of the plant operation study is a plant capable of producing 250kW-equivalent ribbon crystals a year, and the efforts involve the ribbon pulling system, rough cutter, real-size cutter, etching unit, shape checker, packing, devices for production lines such as warehouses for products, electric power, gas, water, peripheral equipment for waste water treatment etc., ribbon specifications check, quality related assistance equipment to deal with unacceptable products etc., pollution-preventing facilities for the preservation of production environments, and plant buildings. (NEDO)

  6. Report on the survey in fiscal 1998. Systematic arrangement of environment technologies. 5 (Application of advanced technologies to environmental measures); 1998 nendo chosa hokokusho. Kankyo gijutsu ni kansuru taikeiteki seiri. 5 (sentan gijutsu no kankyo taisaku eno oyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    Global environment handling technologies were investigated and put into order. Universities often make research and development on themes that can be handled at laboratory levels or by simulations. Development at a practical application level is few. Technological seeds may include manufacture of hydrogen by water and steam decomposition using solar energy, and new synthesizing reactions utilizing solar energy. Included may also be urban type wind power generation, superconductive energy storage systems, biomass utilization, and natural energy utilization. Furthermore, CO2 recovery and utilization by liquefaction, alkaline metal heat power generation, and pulse power technologies can also be found. Studies on applying advanced technologies to environmental measures include composite materials, membrane separation, photo-catalysts, optical elements, porous bodies, functional polymers, bio-reactors, electron beams, and aeration. Private corporations are working noticeably on prevention of fluorocarbon and dioxin emission, PCB treatment and waste water treatment technologies, catalyst application technologies, recycling technologies, and incineration ash treatment and utilization technologies. (NEDO)

  7. Energy: nuclear energy

    International Nuclear Information System (INIS)

    Lung, M.

    2000-11-01

    Convinced that the nuclear energy will be the cleaner, safer, more economical and more respectful of the environment energy of the future, the author preconizes to study the way it can be implemented, to continue to improve its production, to understand its virtues and to better inform the public. He develops this opinion in the presentation of the principal characteristics of the nuclear energy: technology, radioactive wastes, radiation protection, the plutonium, the nuclear accidents, the proliferation risks, the economics and nuclear energy and competitiveness, development and sustainability. (A.L.B.)

  8. Future energy, exotic energy

    Energy Technology Data Exchange (ETDEWEB)

    Dumon, R

    1974-01-01

    The Detroit Energy Conference has highlighted the declining oil reserves, estimated worldwide at 95 billion tons vs. an annual rate of consumption of over 3 billion tons. The present problem is one of price; also, petroleum seems too valuable to be simply burned. New sources must come into action before 1985. The most abundant is coal, with 600 billion tons of easily recoverable reserves; then comes oil shale with a potential of 400 billion tons of oil. Exploitation at the rate of 55 go 140 million tons/yr is planned in the U.S. after 1985. More exotic and impossible to estimate quantitatively are such sources as wind, tides, and the thermal energy of the oceans--these are probably far in the future. The same is true of solar and geothermal energy in large amounts. The only other realistic energy source is nuclear energy: the European Economic Community looks forward to covering 60% of its energy needs from nuclear energy in the year 2000. Even today, from 400 mw upward, a nuclear generating plant is more economical than a fossil fueled one. Conservation will become the byword, and profound changes in society are to be expected.

  9. Nuclear energy and renewable energies

    International Nuclear Information System (INIS)

    1994-01-01

    The nuclear energy and the renewable energies namely: solar energy, wind energy, geothermal energy and biomass are complementary. They are not polluting and they are expected to develop in the future to replace the fossil fuels

  10. Energy crisis

    International Nuclear Information System (INIS)

    1977-01-01

    From energy policy to the problem of public acceptance of nuclear power, problems like energy supply, energy strategies, the race of industrial countries for the short energy reserves, the West German energy demand until the year 2.000, energy conservation, and the controversy over increased use of nuclear energy are reviewed. (GL) [de

  11. Achievement report for fiscal 1997. Technological development for practical application of a solar energy power generation system/development of technology to manufacture thin film solar cells/development of technology to manufacture low-cost large-area modules/development of technology to manufacture next generation thin film solar cells (development of technology to manufacture applied type thin film solar cells with new construction); 1997 nendo tiayoko hatsuden system jitsuyoka gijutsu kaihatsu. Usumaku taiyo denchi no seizo gijutsu kaihatsu, tei cost daimenseki module esizo gijutsu kaihatsu (jisedai usumaku taiyo denchi no seizo gijutsu kaihatsu, oyogata shinkozo usumaku taiyo denchi no seizo gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    A thin film single crystal silicon solar cell module is developed, in which a porous silicon layer is formed on the surface of a long-sized single crystal silicon substrate, a single crystal silicon film is integrated on the layer by epitaxially growing the film thereon to form a solar cell, and the solar cell is peeled off from the silicon substrate and transferred to a plastic film substrate. The achievements during this fiscal year may be summarized as follows: simultaneous formation of a porous silicon layer on a silicon substrate, reduction of anode formation current density from 200 mA/cm{sup 2} to 10 mA/cm{sup 2}, development of a silicon epitaxial device using a carbon heater, and attainment of aperture conversion efficiency of 11.8% in a thin film single crystal silicon solar cell. Three kinds of methods were developed to peel off the solar cell. A method was developed to grind silicon substrate surface from which the solar cell has been peeled off. A technology was developed to obtain a long-sized silicon substrate of about 30 cm times 10 cm times 0.1 cm from a 4-inch silicon ingot by using a wire saw. (NEDO)

  12. Tidal energy

    International Nuclear Information System (INIS)

    Lochte, H.G.

    1995-01-01

    Together with wave energy, ocean thermal energy, and the often overlooked energy from ocean curents tidal energy belongs to those renewable energy sources that can be subsumed under the generic term of ocean energy. All that these energy sources have in common, however, is that they are found in the ocean. The present article discusses tidal energy with respect to the four principal factors determining the scope of a renewable energy source, namely global, technical, and economic availability and ecological acceptability. (orig.) [de

  13. Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

  14. Surveys and researches on trends of technologies related to hydrogen; Suiso ni kansuru gijutsu doko chosa kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1983-03-01

    This report covers surveys of the latest technological trends in relation to the production, storage, and transportation of hydrogen as energy. Also included in the report are surveys of hydrogen, fuel cells, and wind energy centering about Europe. At the 4th World Hydrogen Energy Conference (Pasadena, U.S., June 1982), a number of essays were presented concerning the utilization of hydrogen, production of hydrogen, thermochemical processes, hybrid processes, photochemical processes, photo/thermochemical processes, other processes, fuel cells, metallic hydrides, etc. This report particularly describes in detail the trends of technologies involving the production of hydrogen by the electrolysis of water and by thermochemical processes. As for the recent trend of the metallic hydride technology, reports are made on the International Symposium on the Properties and Applications of Metal Hydrides (Toba, Japan, June 1982) and on Japan's research on the application of metallic hydrides. Concerning the trends in Europe of technologies relative to hydrogen, fuel cells, and wind energy, the results of the research group's on-site investigations are reported. (NEDO)

  15. NEDO Forum 2001. Session on advanced power generation and storage technology development; NEDO Forum 2001. Shindenryoku gijutsu kaihatsu session

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session and remarks made at the panel discussion of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. Predicted by Deputy Chairman Tanaka of International Superconductivity Technology Center in his lecture entitled 'Energy problem in IT (information technology) oriented society' were that possibilities were high that power consumption would rapidly increase in line with the progress of broad band and wireless, that energy conservation and environmental technologies should be developed urgently, and that superconductivity technology would assume an important role. Discussed at the panel on 'Prospect of distributed power sources in power systems' were 'Power utilization by information communication in IT-oriented days and needs for development,' 'Energy utilization involving buildings and needs for development,' 'Tasks to discharge in cogeneration technology development and coordination with power systems,' 'Technical problems involving interconnection of distributed power sources and needs for development,' 'Present state of distributed power sources and needs for development,' and 'From Fuel and Storage Technology Development Department to Advanced Power Generation and Storage Technology Development Department.' (NEDO)

  16. Achievement report on development of global warming prevention related technologies in fiscal 1998. Development of environment harmonizing type dye finishing technology; 1998 nendo chikyu ondanka boshi kanren gijutsu kaihatsu seika hokokusho. Kankyo chowagata senshoku seiri gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    The dye finishing operation in the textile industry places heavy load on the global environment. This paper describes the achievements in fiscal 1998 on development of process to eliminate the load. Low-temperature plasma treatment was introduced into the desizing and refining process to develop a continuous treatment process using no water and chemicals. Quality equivalent to that produced by conventional methods was obtained by applying an appropriate plasma treatment condition. The energy saving rate was presented by reduction by 84.3% converted into steam. Conventional dye finishing operation uses three to six times as much water as the cloth weight. The developed air flow treatment device reduced the water ratio to less than one. This is 86.0% reduction of energy consumption converted to steam. In removing pectic substance in cotton refining, no water, chemicals and steam were used, but were substituted by enzyme for continuous treatment. Good finishing result was obtained by performing bleaching and dying. Enzyme cost is an issue, but the cost would decrease if it is used in large quantity. A two-dimensional colorimeter (measures cloth color with high clarity and reproducibility) and an automatic dye preparing device (with high volume measuring performance) were developed. If the cost required for re-coloring under the present inspection method is converted into energy, it corresponds to 81.6% reduction. (NEDO)

  17. FY 1998 annual summary report on photon measuring/processing techniques. Development of the techniques for high-efficiency production processes; 1998 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to develop the techniques for energy-efficient laser-aided processing; techniques for high-precision, real-time measurement to improve quality control for production processes and increase their efficiency; and the techniques for generating/controlling photon of high efficiency and quality as the laser beam sources therefor, in order to promote energy saving at and improve efficiency of production processes consuming large quantities of energy, e.g., welding, joining, surface treatment and production of fine particles. The R and D themes are microscopic processing technology: simulation technology for laser welding phenomena; microscopic processing technology: synthesis of technology for quantum dot functional structures; in-situ status measuring technology: fine particle elements and size measurement technology; high-power all-solid-state laser technology: efficient rod type LD-pumping laser modules and pumping chamber of a slab-type laser; tightly-focusing all-solid-state laser technology: improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology and fabrication technology for nonlinear crystal; and comprehensive investigation of photonics engineering: high-efficiency harmonic generation technology. (NEDO)

  18. Achievement report for fiscal 1981 on the development of solar energy technologies for the development of practical application technologies for photovoltaic power systems. Experimental fabrication of solar cell panels and verification thereof (Development of technologies for panel assembly process); 1981 nendo taiyo energy gijutsu kenkyu kaihatsu seika hokokusho (taiyoko hatsuden system jitsuyoka gijutsu kaihatsu). Taiyo denchi panel jikken seisaku kensho (panel kumitate kotei no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1982-03-01

    In a study of cell array connection process, continuous and automatic connection of cells is named as the basic concept in view of low cost and high reliability. In the designing of details of cell strings, CZ (Czochralski) cell dimensions are reviewed for cell packaging efficiency improvement, interconnectors and wiring are examined for a easier packaging process, and solder connection is thought over for utility cost reduction. Conditions are established for string fabrication process details. In the study of the panel packaging process, panel package designing is carried out and a dedicated mechanical device is installed. In the study of the inspection process and plant system, data are collected, necessary for the construction and adjustment of an inspection device. Research is conducted on the layout of plant facilities, on required utilities, and on facilities operating state signals to be transmitted to the central control unit. As for an inspection jig supply system, transfer system, and storage rack, they are designed, built, and installed. The plant house is now complete. (NEDO)

  19. Report on achievements in fiscal 1999 on research and development of immediately effective and innovative energy environment technology. Part 1. Development of immediately effective and high-efficiency solar cells, and development of technology to slice and manufacture thin-type large-area polycrystalline substrates; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu seika hokokusho. Sokkogata kokoritsu taiyo denchi gijutsu kaihatsu (usugata daimenseki takessho kiban slice seizo gijutsu kaihatsu 1)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective of decreasing silicon usage quantity for the purpose of reducing the solar cell production cost, development is being performed on an ingot cutting technology to cut a silicon ingot to Kerf loss of 150 {mu} m and thickness of 150 {mu} m, and in which the produced wafers can withstand the cell making. Investigations revealed that a wire saw is suitable as the cutting system, and the wire used must have a diameter of less than 120 {mu} m, and a strength of more than 3850 N/mm{sup 2}. A prototype wire was fabricated, whose diameter is 120 {mu} m, and in which the strength is distributed between 3870 and 4110 N/mm{sup 2}. It was found possible that a wire of 160 {mu} m can be used to slice an ingot having a cross section surface of 150 mm square and a length of 300 mm into a slice having a Kerf loss of 200 {mu} m and a thickness of 180 {mu} m. This wafer had the in-plane distribution of the substrate thickness at {+-} 12.5 {mu}, swell of 120 {mu} at maximum, and surface roughness of 5 {mu}. Making ten of these wafers into a cell resulted in a yield of 60%. Assignments are the clarification of the properties of the cutting wire, the preparation of a thin wire with homogeneous quality, and the establishment of a technology to cut Kerf loss of 150 {mu} and substrate thickness of 150 {mu}. (NEDO)

  20. Fiscal 1999 research report on long-term energy technology strategy. Basic research on industrial technology strategy (Individual technology strategy). Human life, medical care and welfare field (Medical health care technology field); 1999 nendo choki energy gijujtsu senryaku ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (bun'yabetsu gijutsu senryaku) ningen seikatsu iryo fukushi bun'ya (medidal health care gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on Japanese technology competitiveness, future trend, technology innovation and policy needs in a medical health care field. Future international growth of a medical health care equipment industry is promising because of an expected progress of medical care technology, change in medical care needs and creation of the new global market. The current highlighted technical trend is fusion of medical technology with network, system, biotechnology and micro-machine technologies, and such fusion is expected to contribute to daily use, less/no invasion and improvement of medical treatment. Industry-government cooperative measures for upgrading an international competitiveness are as follows: an approach as national policy by preparing Japanese BECOM, preparation of a system supporting venture businesses for developing medical health care equipment, and systematic establishment of a medical-engineering cooperative system. Preparation of a complementary relation with overseas countries is also desirable. (NEDO)

  1. Industrial and scientific technology research and development project in fiscal 1997 commissioned by the New Energy and Industrial Technology Development Organization. Research and development of superconducting materials and transistors (report on overall investigation of superconductive devices); 1997 nendo sangyo kagaku gijutsu kenkyu kaihatsu jigyo Shin energy Sangyo Gijutsu Sogo Kaihatsu Kiko itaku. Chodendo zairyo chodendo soshi no kenkyu kaihatsu (chodendo soshika gijutsu kaihatsu seika hokokusho)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    This paper describes development of superconducting new function transistors. Fiscal 1997 as the final year of the project advanced improvement in such transistor-using processes as formation and micro-processing of superconducting thin films to show enhancement in characteristics of high-temperature superconducting transistors and possibility of their application utilizing their high speed motions. Furthermore, fundamental technologies were studied with an aim on junction transistors to be applied as circuits. For field effect transistors, evaluation was performed on critical current distribution of step-type particle boundary junction to make it possible to evaluate characteristics of hundreds of transistors. At the same time, a magnetic flux quantum parametron gate with three-layer structure was fabricated to identify its operation. In superconducting-base transistors, strong reflection was recognized on temperature dependence of permittivity of an Nb-doped strontium titanate substrate used for collectors, by which barrier height was reduced. In the junction transistor and circuit technology, isotropic ramp-edge junctions were fabricated, and so was a frequency divider circuit with single magnetic flux quantum mode operation for evaluating high-speed response characteristics. High time resolution current was observed successfully by using a high-temperature superconducting sampler system. 148 refs., 127 figs., 4 tabs.

  2. Fiscal 1997 report on the development of an energy use rationalization ultra-high tech liquid crystal technology. Project of development/promotion of ultra-high tech electronic technology / technology of design/control/analysis of new functional electronic materials; 1997 nendo kenkyu seika hokokusho energy shiyo gorika chosentan ekisho gijutsu kaihatsu. Chosentan denshi gijutsu kaihatsu sokushin jigyo / shinkino denshi zairyo sekkei seigyo bunseki gijutsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-05-01

    A research was conducted with the aim of developing an ultra-low power consuming type information display which supports the next next generation informatizing society. As to the function combined type fine structure formation technology, a formation technology of fine structure supporting multi-layer pixel by organic polymer materials was established to confirm a possibility of adopting it to high functional liquid crystal display. Concerning the high functional fine structure formation technology, a study was proceeded with on holographic PDLC which is an interference reflection coloring method. In relation to the low temperature film formation technology of ferroelectric thin films, a film formation device was introduced to obtain basic data, and at the same time a possibility was studied of improving film characteristics by laser annealing conducted after the film formation. Moreover, concerning the new functional material technology, studies were made of optical interference/high light-scattering control materials, light alignment elements, ultra-high purity/ultra-reliable optical materials, ultra-anisotropy optical materials, etc. About the light reflection characteristics control technology, studied were new liquid crystal molucular orientaion control technology, multi-dimensional anisotropy structure formation technology, etc. 100 refs., 273 figs., 58 tabs.

  3. FY 2000 report on the survey of long-term energy technology strategy, etc. - Fundamental survey to work out the industrial technology strategy. Research survey on analysis of trends of technical innovation in Japan/Europe/the U.S.; 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiso chosa (Nichibeio no gijutsu kakushin doko no bunseki ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For survey of the industrial competitive force, it is important to arrange the environment where the continuous and spontaneous technical innovation is generated. To recognize the present situation, the patent information relating to technical innovation, etc. were collected, indices of the number of patent, degree of the reference and scientific link in Japan, the U.S., and Europe were taken out by technology field to analyze the patent trend in the past 10 years. By technology field, the U.S. is superior in a lot of fields. Japan is at top rank in office supplies and camera fields, made strenuous efforts in automobile and semiconductor/electronic fields, but is behind others in medicine, biotechnology and aerospace fields. Concerning the number of patent registration in the U.S., Japan is superior to the U.S. in automobile/electric equipment/metal industries. Europe is superior in food and engineering fields. The U.S. is superior in aerospace industry and biotechnology fields. The U.S. is featured by a large number of patent applications by universities and government organizations. (NEDO)

  4. Energy Fact Sheets - Sandia Energy

    Science.gov (United States)

    Energy Energy Secure & Sustainable Energy Future Search Icon Sandia Home Locations Contact Us Employee Locator Menu Stationary Power solar Energy Conversion Efficiency Increasing the amount of electricity produced from a given thermal energy input. Solar Energy Wind Energy Water Power Supercritical CO2

  5. Energy options?; Energie opties?

    Energy Technology Data Exchange (ETDEWEB)

    Van Sark, W. (ed.)

    2006-05-15

    March 2006 the so-called Options Document was published by the Energy research Centre of the Netherlands (ECN) and the Netherlands Environmental Assessment Agency (MNP). The document is an overview of technical options to reduce energy consumption and emission of greenhouse gases up to 2020. Next to a brief summary of the document a few reactions and comments on the contents of the document are given. [Dutch] Maart 2006 publiceerde het Energieonderzoek Centrum Nederland (ECN) en het Milieu- en Natuurplanbureau (MNP) het zogenaamde Optiedocument energie en emissies 2010-2020. Daarin wordt een overzicht gegeven van de technische mogelijkheden voor vermindering van het energieverbruik en de uitstoot van broeikasgassen en luchtverontreinigende stoffen tot 2020. Naast een korte samenvatting van het document worden enkele reacties gegeven op de inhoud.

  6. Energy Technology.

    Science.gov (United States)

    Eaton, William W.

    Reviewed are technological problems faced in energy production including locating, recovering, developing, storing, and distributing energy in clean, convenient, economical, and environmentally satisfactory manners. The energy resources of coal, oil, natural gas, hydroelectric power, nuclear energy, solar energy, geothermal energy, winds, tides,…

  7. Research on EBEP (Electron Beam Excited Plasma) applications; EBEP (denshi beam reiki plasma) no tekiyo gijutsu ni kansuru kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    Yanase, E.; Ryoji, M.; Mori, Y.; Tokai, M. [Kawasaki Heavy Industries, Ltd., Kobe (Japan)

    1996-04-20

    Research and development is actively conducted on machining technologies using plasma in various fields, with studies energetically pursued on etching techniques or those of forming a thin film by the use of high frequency and microwave plasma. The EBEP system jointly developed by Kawasaki Heavy Industries Ltd. and Institute of Physical and Chemical Research is a plasma source for forming a high density plasma by implanting into a plasma chamber from the outside a high-current electron beam accelerated to an energy of approximately 60 to 100eV where the collision cross-section of gas ionization is maximized. The characteristics of the system are such as (1) it enables electron energy distribution to be controlled from outside by varying acceleration voltage, (2) it excels in the controllability of ion energy and (3) it allows to form a steady high-density plasma in a nonmagnetic field. This paper presents the generating principle of EBEP, its plasma characteristics, etching technique using EBEP, thin film forming technique by EBEP-CVD method, and multipurpose apparatus for research and development. 6 refs., 7 figs., 1 tab.

  8. NEDO environmental technology subcommittee. 18th project report meeting; NEDO kankyo gijutsu bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    In relation with the 'recent trends of global warming problems and the outline of environmental technology development office activities,' Hiroshi Mitsukawa, a NEDO (New Energy and Industrial Technology Development Organization) director, delivers a report on Japan's policy toward the international commitments of the Kyoto session of the Conference of the Parties to the United Nations Framework Convention on Climate Change and NEDO's approach in this connection to new energy technology development. Furthermore, global environment-related industry technology research and development projects are explained, which involve environmentally friendly production technology, reduction in substances that cause environmental impacts, effective use of CO2 fixation, recycling of wastes, environment restoration technology, international relationship, and so forth. In relation with the 'promotion of global warming prevention projects by the environmental technology development office,' researches for the promotion of joint implementation, climate technology initiative, international joint projects for CO2 isolation in the ocean, and IEA (International Energy Agency) agreement on the research and development of technologies related to greenhouse gas, are explained. Concerning the development of eco-cement production technology utilizing urbane type general wastes, a verification research project on the manufacture of cement from incinerated urbane waste residue and sewage sludge is reported. (NEDO)

  9. Report on achievement for fiscal 1998. Global environment industry technology development promotion project (the advanced technology survey and research project); 1998 nendo seika hokoiusho. Chikyu kankyo sangyo gijutsu kaihatsu suishin jigyo (sentan gijutsu chosa kenkyu jigyo)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In order to structure innovative technologies to solve effectively the global environment problems, it is important to incorporate infra-structural technologies that have been achieved by universities and other research institutions. The fiscal 1998 project has commissioned 25 researches found superior from among research plans that have been invited during fiscal 1997. This paper enumerates the main themes including those under continued research. The research themes include: fixation of phosphor by using photo-energy, utilization of nitrogen fixing bacteria in rice plant roots for the purpose of carbon dioxide reduction, new functional solid ultra-strong acids for clean chemical processes, fixation of warming gases by using ultra critical fluid catalytic reactions, photo-catalysts having microporous structure, whose energy structure is controlled, waste water purification by using stimulation sensitive polymers, a practical and small high-speed environment purification system by means of a simple technology to cultivate high concentration bacteria of microorganisms, fundamental analysis of response to specific wavelength light in photosynthesized microorganisms, bio-remediation utilizing symbiotic systems of plants and bacteria, high efficiency catalysts purposed for total decomposition of water, and separation of carbon dioxide in deep sea bottoms by controlling hydrate crystal growth. (NEDO)

  10. Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of high- efficiency production process technology); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Kokoritsu seisan process gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on R and D of laser processing technology, in-situ measurement technology, and generation and control technology of photon as laser beam source, for energy saving and efficiency improvement of energy-consumptive production processes such as welding, jointing, surface treatment and fine particle fabrication. The research was carried out by a technical center, 9 companies and a university as contract research. The research themes are as follows: (1) Processing technology: simulation technology for laser welding phenomena, synthesis technology for quantum dot functional structures, and fabrication technology for functional composite materials, (2) In-situ measurement technology: fine particle element and size measurement technology, (3) All- solid state laser technology: efficient rod type LD-pumping laser module, pumping chamber of slab type laser, improvement of E/O efficiency of laser diode, high-quality nonlinear crystal growth technology, fabrication technology for nonlinear crystals, and high-efficiency harmonic generation technology. Comprehensive survey was also made on high- efficiency photon generation technologies. (NEDO)

  11. FY 1992 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1992 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1992 as the third year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

  12. FY 1999 report on the results of the development of technology of super metal. Development of nano/amorphous structure control materials; 1999 nendo super metal no gijutsu kaihatsu seika hokokusho. Nano amorphous kozo seigyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of reducing the amount of energy consumption of transportation equipment such as automobiles, the development is made of innovative metal materials enabling the weight reduction of members relatively on the basis of simple chemical components and by making more substantial improvement of characteristics such as strength and toughness than in the existing metals. For it, the following R and D are conducted in which nano crystal structure and non-equilibrium phase structure such as amorphous are controlled to the limits: 1) particle micro-dispersion technology; 2) high speed super plastic formation technology; 3) high density energy utilization control technology; 4) control cooling technology. In 1), study was made of alloy components and effects of the creation process which are needed for achievement of the nano level of crystal grain. In 2), conditions of vapor deposition and production in high speed particle deposition method are optimally selected, and amorphous and nano crystal structures can easily be produced. In 3), high corrosion-resistant amorphous alloy bulk materials with 5mm thickness and 10mm diameter were successfully trially manufactured. In 4), a bulk amorphous specimen with 10mm outer diameter, 6mm inner diameter and 1mm thickness which was fabricated in the forging method indicated favorable magnetic properties. A method to make a specimen which is more stable is being studied. (NEDO)

  13. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of advanced-function maintenance technology for power generation facilities; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Technologies for integrating functions are studied for a self-propelled surroundings recognition system that travels in a small-diameter tube at power generation facilities. Parameters are analyzed, and piezoelectric locomotion devices are reduced in size. A disk shape microantenna is experimentally built and evaluated, which is for realizing energy supply and communication by means of microwaves. Studies are conducted to improve the performance of optical energy transmission devices and to realize their systematization. Basic specifications are established for the embodiment of CCD (charge coupled device) microcameras to be installed. A high-efficiency, high-reliability micromachine system is constructed, in which multiple machines coordinate with each other for the exterior inspection of groups of small-diameter tubes. Devices which are capable of driving, deceleration, and propulsion prove to be feasible. Basic specifications are established for microconnectors to connect, separate, and combine multiple machines as occasion calls. Also discussed is the development of a micromachine for tube interior check and repair which operates making use of the inspection hole enabling tube interior check and repair without the need of disassembling the equipment to be repaired.

  14. FY 1998 annual summary report on photon measuring/processing techniques. Development of highly functional maintenance techniques for power generating facilities; 1998 nendo foton keisoku kako gijutsu. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    The objectives are set to develop the techniques for non-destructive measurement of conditions of facility portions, especially those exposed to severe environments, e.g., elevated temperature and pressure, over a wide range; the techniques for measurement of leakage of, e.g., gases, at high sensitivity; the techniques of laser-aided welding and surface-modification treatment for the members exposed to severe conditions; and the techniques for generating photon beams of high quality and energy density as the tools therefor, in order to improve reliability and maintenance efficiency of power generating facilities. The R and D themes are microscopic processing technology: fabrication technology for functional micro-composite circuits; in-situ status measuring technology: gas concentration/component measurement technology, and photon wavefront compensation device technology; non-destructive composition measuring technology: high-sensitivity detection technology using short-wavelength photons; high-power all-solid-state laser technology: rod-type laser and slab-type laser; tightly-focusing all-solid-state laser technology: high-energy pulse, high-quality laser; and comprehensive investigation of photonics engineering: investigation for photon-applied measurement technologies. (NEDO)

  15. FY 1990 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1990 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1991-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1990 as the initial year include negotiations with the Philippines, on-the-spot surveys for the demonstration plant sites and conditions, and conceptual designs of the demonstration plant. (NEDO)

  16. Research and development of evaluation system for photovoltaic power generation system. Research and development on evaluation technology of photovoltaic power generating systems; Taiyoko hatsuden system hyoka gijutsu no kenkyu kaihatsu. System hyoka gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on R and D of evaluation technology for photovoltaic power generating systems in fiscal 1994. (1) On preparation of test facility and measuring instrument, the pyrheliometer with a photovoltaic device as sensor was developed. (2) On collection and analysis of data, operation data of interconnection system, stand alone system, and water pump system were collected, and energy flow was analyzed. The following were also analyzed: time variation of a-Si solar cell modules, fluctuation correction factor of spectrum response, that of nonlinear response of crystalline solar cells, effect of solar radiation intensity and wind velocity on temperature rise of modules, and correction factor of DC circuit losses. (3) On on-site measurement technology, the array output measuring instrument was developed on the basis of capacitor charge system. (4) On simulation technology, simulation analyses of energy flow, optimum capacity of interconnection systems, correction factor of solar radiation, and capacity of array storage batteries were conducted. 3 figs., 6 tabs.

  17. FY 1991 report on the development of wood-waste/agri-waste pyrolytic gasification technology and utilization technology of gas product; 1991 nendo mokushitsukei haikibutsu no netsubunkai gas ka gijutsu to seisei gas no riyo gijutsu kaihatsu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1992-03-01

    It is urgently necessary for the Philippines, which has no promising energy source to replace imported oil and lacks hard currencies, to reduce dependence on oil. The country, consisting of a number of islands, has faced many difficulties in construction of large-scale power transmission grids covering wide areas, which greatly retard development of local industries and dissemination of electricity. Therefore, great expectations have been placed on the techniques this project plans to develop for utilization of wastes as the energy source. This 5-year project (FY 1990 to 1994) is aimed at joint research and development of (thermal decomposition/gasification and power generation system) for transforming large quantities of wood-wastes/agri-wastes left unutilized into electric power, in which thermal decomposition/gasification of the wastes is combined with gas engine/power generator systems, and thereby to establish the systems suitable for the developing country. The major R and D results obtained in FY 1991 as the second year include on-the-spot surveys, tests for validating elementary techniques, designs and fabrication of part of the demonstration plant, and invitation of Philippine researchers to Japan. (NEDO)

  18. Energy storage

    International Nuclear Information System (INIS)

    2012-01-01

    After having outlined the importance of energy storage in the present context, this document outlines that it is an answer to economic, environmental and technological issues. It proposes a brief overview of the various techniques of energy storage: under the form of chemical energy (hydrocarbons, biomass, hydrogen production), thermal energy (sensitive or latent heat storage), mechanical energy (potential energy by hydraulic or compressed air storage, kinetic energy with flywheels), electrochemical energy (in batteries), electric energy (super-capacitors, superconductor magnetic energy storage). Perspectives are briefly evoked

  19. Chlorofluorocarbons (CFCs) destruction technology by induction coupled plasma; Koshuha purazuma ni yoru tokutei furon hakai gijutsu ni tsuite

    Energy Technology Data Exchange (ETDEWEB)

    Kobayashi, A. [Nippon Steel Corp., Tokyo (Japan)

    1999-09-05

    Abolishing flon in which the reuse by pollution and degradation is difficult by recovery flon and recovery and recycling process which do not rotate for the middle reuse that the recovery system is constructed is arising. And, the specific flon recovery quantity increases with the progress of development of the recent CFC substitute and renewal to the CFC substitute correspondence machine. Specific flon collapse technique using rf plasma introduced in this paper cultivated the basic technology in Agency of Industrial Science and Technology, resources environment integrated research place. The demonstrated operation research was carried out under Ministry of International Trade and Industry, New Energy and Industrial Technology Development Organization since December 1994. (NEDO)

  20. Renewable energy

    International Nuclear Information System (INIS)

    Yoon, Cheon Seok

    2009-09-01

    This book tells of renewable energy giving description of environment problem, market of renewable energy and vision and economics of renewable energy. It also deals with solar light like solar cell, materials performance, system and merit of solar cell, solar thermal power such as solar cooker and solar collector, wind energy, geothermal energy, ocean energy like tidal power and ocean thermal energy conversion, fuel cell and biomass.

  1. Energy storage

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter discusses the role that energy storage may have on the energy future of the US. The topics discussed in the chapter include historical aspects of energy storage, thermal energy storage including sensible heat storage, latent heat storage, thermochemical heat storage, and seasonal heat storage, electricity storage including batteries, pumped hydroelectric storage, compressed air energy storage, and superconducting magnetic energy storage, and production and combustion of hydrogen as an energy storage option

  2. Dossier Energy

    International Nuclear Information System (INIS)

    Weijer, H.; Holwerda, B.; Schrauwers, A.; Van de Graaf, A.; Van Gelder, T.

    2003-01-01

    Several aspects with respect to energy are discussed in a special section of this magazine: the security of energy supply in a liberalized market, saving energy by outsourcing (e.g. compressed air contracting), the profits of a liberalized energy market for businesses, incentives for energy saving projects and innovations, an energy efficiency project at Ineos Silicas (producer of zeolites), and energy efficient electronic equipment [nl

  3. Energy intermittency

    CERN Document Server

    Sorensen, Bent

    2014-01-01

    The first book to consider intermittency as a key point of an energy system, Energy Intermittency describes different levels of variability for traditional and renewable energy sources, presenting detailed solutions for handling energy intermittency through trade, collaboration, demand management, and active energy storage. Addressing energy supply intermittency systematically, this practical text:Analyzes typical time-distributions and intervals between episodes of demand-supply mismatch and explores their dependence on system layouts and energy source characteristicsSimulates scenarios regar

  4. Long-distance power transmission technology. Microwave power transmission; Denryoku no chokyori yuso gijutsu. Micro ha musen soden

    Energy Technology Data Exchange (ETDEWEB)

    Kaya, N [Kobe University, Kobe (Japan). Faculty of Engineering

    1994-11-05

    This paper explains the principles of microwave power transmission as a long-distance power transmission technology, and the status of its development. Under an assumption of using a wave length of 12 cm (2.45 GHz) and a transmission distance of 1 km, an ideal wireless power transmission can realize transmitting the power at an efficiency of 95% or higher if transmitting and receiving antennas with a radius of 8.8 m are used. What remains as important requirements is raising the efficiency of conversion from power supply into microwaves, and the efficiency of rectification after the power has been received. By using microwave energy sent from a transmission antenna installed on the roof of an automobile, a model airplane with a receiving antenna installed at its rear flew successfully for 40 seconds under the microwave lifted airplane experiment (MILAX). In an experiment of transmitting microwave power in space, power was successfully transmitted to the child rocket as an event under the International Space Year - Microwave Energy Transmission in Space (ISY-METS). The microwave wireless power transmission on the ground would have a possibility of taking over the overhead line transmission into islands. An attempt is scheduled to send power of 5 kW by using transmission and receiving antennas with a diameter of 3 m to investigate effects on transmission efficiency, and communications and electromagnetic environments, and to collect basic data. 3 refs., 3 figs.

  5. Development of practical application technology for photovoltaic power generation systems in fiscal 1997. Development of technologies to manufacture next-generation thin film solar cells, development of technologies to manufacture CIS solar cell modules, development of technologies to increase high-quality film area; 1997 nendo taiyoko hatsuden system jitsuyoka gijutsu kaihatsu. Jisedai usumaku taiyo denchi module no seizo gijutsu kaihatsu, CIS taiyo denchi module no seizo gijutsu kaihatsu, kohinshitsumaku no daimensekika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    With an objective to improve efficiency and reduce cost of CIS-based thin film solar cells, research and development has been made on technologies to increase high-quality CIS film area and technologies to increase speed in the manufacturing process. This paper describes the achievements attained during fiscal 1997. The research covered development of technologies to form high-grade Cu (In, Ga) Se{sub 2} (CIGS) film by using the multi-dimensional deposition process, component technologies for forming a rear electrode, a buffer layer and a transparent electrode, and patterning technologies. As a result of the research, thickness of the CIGS film was reduced to half as much as that of the conventional films, having achieved conversion efficiency of 13.1%, which corresponds to about 90% of the conventional CIGS solar cells. In addition, elucidation was made on the effect of an MoSe{sub 2} layer existing on interface with CIGS/Mo in a CIGS solar cell imposed on solar cell characteristics. In developing an Mo film laser scribing technology, intensity dependence of laser energy was made clear, the energy being required for scribing according to surface condition of the Mo film. (NEDO)

  6. Fiscal 1993 investigational report on heat pump heat storage technology; 1993 nendo heat pump chikunetsu gijutsu ni kansuru chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1994-03-01

    This project is for an investigation into the heat pump (HP) use heat storage technology, with the aim of clarifying the present status of HP heat storage technology, the utilization status, and the developmental trend of technology and of contributing to the spread of heat energy effective use using HP heat storage technology and to the promotion of the technical development. Accordingly, the evaluation of the following was made: sensible heat (SH), latent heat (LH), chemical heat storage technology (CH), and heat storage technology (HS). Investigations were made on the sensible heat use heat storage technology of water, brine, stone, soil, etc. in terms of SH; the phase change sensible heat use heat storage technology of ice, hydrate salt, paraffins, etc. in terms of LH; hydration, hydroxide, 2-propanol pyrolysis, adsorption of silica gel, zeolite and water, and heat storage technology using metal hydride, etc. in terms of CH. In terms of HS, the following were studied and evaluated from the study results of the heat storage system in which HP is applied to the sensible heat and latent heat type heat storage technology: contribution to the power load levelling and the reduction of heat source capacity, heat recovery and the use of unused energy, improvement of the system efficiency by combining HP and heat storage technology. 24 refs., 242 figs., 56 tabs.

  7. Energy sustainability through green energy

    CERN Document Server

    Sharma, Atul

    2015-01-01

    This book shares the latest developments and advances in materials and processes involved in the energy generation, transmission, distribution and storage. Chapters are written by researchers in the energy and materials field. Topics include, but are not limited to, energy from biomass, bio-gas and bio-fuels; solar, wind, geothermal, hydro power, wave energy; energy-transmission, distribution and storage; energy-efficient lighting buildings; energy sustainability; hydrogen and fuel cells; energy policy for new and renewable energy technologies and education for sustainable energy development

  8. Renewable energy.

    Science.gov (United States)

    Destouni, Georgia; Frank, Harry

    2010-01-01

    The Energy Committee of the Royal Swedish Academy of Sciences has in a series of projects gathered information and knowledge on renewable energy from various sources, both within and outside the academic world. In this article, we synthesize and summarize some of the main points on renewable energy from the various Energy Committee projects and the Committee's Energy 2050 symposium, regarding energy from water and wind, bioenergy, and solar energy. We further summarize the Energy Committee's scenario estimates of future renewable energy contributions to the global energy system, and other presentations given at the Energy 2050 symposium. In general, international coordination and investment in energy research and development is crucial to enable future reliance on renewable energy sources with minimal fossil fuel use.

  9. Energy assessments

    International Nuclear Information System (INIS)

    Unruh, T.D.

    1998-01-01

    Energy industry initiatives during the 1970s and during the 1990s are compared. During the 1970s, the objective was to reduce energy consumption and to reduce dependency on foreign fuel. Today, the emphasis is on reducing energy costs and to improve net operating income. The challenges posed by the drive to reduce energy costs are discussed. As a tool in the drive to reduce energy cost, the energy assessment process was described. The process entails a detailed analysis of energy consumption, an investigation of energy rates and an assessment of site conditions and equipment, with a view towards an optimum combination that will lead to energy cost reductions

  10. Energy needs

    International Nuclear Information System (INIS)

    Chateau, Bertrand

    2014-05-01

    The author first discusses the various concepts and definitions associated with energy needs, and then the difference between actual needs and energy needs by distinguishing personal needs, needs of the productive sector, energetic needs and services. In the next part, he discusses how energy needs are assessed. He discusses the relationship between energy needs and energy consumption, how energy consumptions can be analysed and interpreted. He comments how energy needs can be assessed and analysed in time and in space. He notices and explains why economy and climate are the main causes of spatial differences for energy needs per habitant, and comments the evolution of energy consumption over long periods

  11. Energy resources

    CERN Document Server

    Simon, Andrew L

    1975-01-01

    Energy Resources mainly focuses on energy, including its definition, historical perspective, sources, utilization, and conservation. This text first explains what energy is and what its uses are. This book then explains coal, oil, and natural gas, which are some of the common energy sources used by various industries. Other energy sources such as wind, solar, geothermal, water, and nuclear energy sources are also tackled. This text also looks into fusion energy and techniques of energy conversion. This book concludes by explaining the energy allocation and utilization crisis. This publ

  12. Solar Energy.

    Science.gov (United States)

    Eaton, William W.

    Presented is the utilization of solar radiation as an energy resource principally for the production of electricity. Included are discussions of solar thermal conversion, photovoltic conversion, wind energy, and energy from ocean temperature differences. Future solar energy plans, the role of solar energy in plant and fossil fuel production, and…

  13. Understanding Energy

    Science.gov (United States)

    Menon, Deepika; Shelby, Blake; Mattingly, Christine

    2016-01-01

    "Energy" is a term often used in everyday language. Even young children associate energy with the food they eat, feeling tired after playing soccer, or when asked to turn the lights off to save light energy. However, they may not have the scientific conceptual understanding of energy at this age. Teaching energy and matter could be…

  14. Wind energy

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This chapter discusses the role wind energy may have in the energy future of the US. The topics discussed in the chapter include historical aspects of wind energy use, the wind energy resource, wind energy technology including intermediate-size and small wind turbines and intermittency of wind power, public attitudes toward wind power, and environmental, siting and land use issues

  15. Energy policy

    International Nuclear Information System (INIS)

    Forrester, J.W.

    1979-01-01

    The author places the energy problem in the context of world economy. The various obstacles encountered in the United States to spell out a viable national energy policy are cited. A certain number of practical proposals is given to lead to an 'effective policy' which would allow energy economy at the same time as energy development, that is, including nuclear energy [fr

  16. Achievement report for fiscal 1996 on the research and development of technologies for important region. Development of control system technology for combustion with energy use rationalized, etc.; 1996 nendo juyo chiiki gijutsu kenkyu kaihatsu seika hokokusho. Energy shiyo gorika nensho nado seigyo system gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to develop basic technologies to build an SiC device capable of service amid high-temperature surroundings for the advancement and optimization of combustion control systems. In an SiC semiconductor, the Si-C bond is broken when irradiated with ions, and this makes the occurrence of thermal oxidation easy to occur. In the study to form SiC into single-crystal substrates, a substrate with warpage of 10 micrometers or less and surface coarseness of 10 nanometers or less is realized. In the development of sensor technologies, the high-speed CVD (chemical vapor deposition) method is applied for the growth of crystals further on a 3C-SiC layer epitaxially grown by MBE (molecular beam epitaxy) surface control, which improves on layer characteristics. Element technologies are developed for the construction of a 3-terminal element (FET: field effect transistor), which is for the construction of a high-temperature, high-speed SiC device. An effort is made at achieving 3C-SiC hetero-epitaxial growth, etc., on a 3-inch Si substrate using an SiC crystal film formation experimenting apparatus, which aims at constructing a control device. Concerning the combustion control system, the relations between the air/fuel ratio and the emission spectra of radicals OH, CH, and C2 in a flame are made clear. Also referred to are the basic studies being conducted at research institutes such as universities and a survey of technological trends abroad.

  17. Report on the surveys in fiscal 1999 on the long term energy technology strategy investigations. Investigations on foundations to establish industrial technology strategies (Structuring of emphasizing strategies and the circulation type economic society harmonizing with environment); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (jutenka senryaku (kankyo to chowashita junkangata keizai shakai no kochiku))

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper is a survey report for fiscal 1999 on structuring of the circulation type economic society harmonizing with environment. In order for Japan in the 21st century to solve various problems while maintaining sustainable development of the industries and economy, structuring the industrial technology strategies is indispensable. In order to establish targets to structure the circulation type society harmonizing with environment, small targets were broken down and specific technological examples were extracted as seen from categories based on flows of goods and the policy aspects. Then, from the viewpoints of extrication from wastes, reduction of risks caused by harmful substances, and growth under suppression of the global warming, case studies were performed on policy aspects toward the year 2010. Based on these studies, images of the emphasizing strategies were prepared, that are built on three pillars of 'R', the reduction, reuse and recycling. Specific technological examples were extracted comprehensively and specifically from research and development themes in research institutions inside and outside Japan to prepare a fundamental material for establishing the small targets. Furthermore, the examples were classified from the aspects of the three Rs. Areas of technological development seeds and areas with fewer seeds were made clear successfully. (NEDO)

  18. Achievement report in fiscal 2000 on research and development project for immediately effective and innovative energy environment technologies. Development of new natural gas storage technology using adsorbents; 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kyuchaku zai wo mochiita shinkina ten'nen gasu chozo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation with natural gas which contributes to preserving the environment and reducing dependence on petroleum, research and development has been performed on a storage system using adsorbents that allows storage of natural gas at higher density than conventional systems. This paper summarizes the achievements in fiscal 2000. In material development, the current fiscal year has performed the discussions on synthesis of three dimensional complexes. An adsorbent was synthesized successfully that has adsorption performance 2.5 times greater than the secondary complex. In developing an improved activated carbon, an adsorbent was synthesized successfully that has methane adsorption performance four times greater than the compressed gas, by using monolithic activated carbon that uses no binders. Carbon briquettes were manufactured for the basic testing equipment for fuel storage container of natural gas fueled automobiles. In the system development, installation was completed on a bench scale equipment for a gas holder and BOG treatment system, whereas engineering data were acquired from the single-column type high pressure test and two-column type constituent separation and storage test using natural gas. Selection was carried out on applicable vehicle types for the adsorption storage system for natural gas fueled automobiles, and the basic design was made for fabrication of containers of different shapes. (NEDO)

  19. Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 4. Development of motive power generation technology; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 4. Doryoku hassei gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the WE-NET Phase II for Task-4, the development of a motive power generation technology. The objective is to build a 100-kW class single cylinder hydrogen-argon circulating diesel system. For a hydrogen injection valve being the key to the system, development was made on the conventional hydraulic system with quick compression, expansion, and electronics control. Discussions were given on an exhaust gas condenser and a gas-liquid separator to handle gas mixture with low steam concentration. In order to assure the mechanical strength to deal with the argon working gas, super-chargers and expansion turbines were also discussed. When the hydrogen injection pressure is increased from 20 to 25 MPa in the basic test, the combustion speed has increased, and the indicated thermal efficiency has been improved. The same effect was obtained also when the oxygen/argon ratio was increased. Although the thermal loss increases if the oxygen/argon ratio is increased, the loss in the indicated thermal efficiency is compensated by the gain derived from increasing the combustion speed. When argon is used as the working gas, the temperatures in parts of the combustion chamber rise much higher than that in the case of a light oil diesel system. Therefore, discussions were given on materials and structures that can withstand elevated temperatures, and assessments and tests were performed on high-temperature lubricants. (NEDO)

  20. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 3. Conceptual design of the total system (safety measures and evaluation technology); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 3. Zentai system gainen sekkei (anzen taisaku hyoka gijutsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Safety measures and assessment technology were studied for the WE-NET project. As the study result in fiscal 1996, the information on safety design, anomaly and accident was collected and arranged. The information on safety measures, ideology and criterion was also collected by visiting some domestic and overseas organizations experienced about handling of liquid hydrogen (LH). The initial survey was made for the safety design ideology, analytical technique and disaster preventive measures of LNG systems as the similar cold liquid system. Accidents and explosion accident of a hydrogen production plant (water electrolysis) in Germany were analyzed. Events on storage tanks and leakage around the tanks were studied as typical risk of LH considering temporary and LNG system design information. The model based on the LH spillage test result and 3-D dispersion of vapor cloud were prepared by modifying a simulation code. The model allowed evaluation of the effect of explosion and fire accidents of compressed hydrogen gas and flying fragments on structures and people, and visual display of distances from a tank and damage conditions. 19 refs., 29 figs., 18 tabs.

  1. FY 1999 report on the result for research and development of instantaneously effective and innovative energy and environment technology. Development of technology to use combustible wastes as resources and fuels; 1999 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu kanengomi saishigen nenryoka gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Manufacturing compressed fuel, or refuse paper and plastic fuel (RPF) from combustible wastes such as used papers and waste plastics to utilize them effectively as a fuel to substitute fossil fuels is regarded as a promising engagement. However, this process indispensably requires removal of chlorine contained in used papers and waste plastics to a degree that they do not impede the combustion. The present research and development is intended to develop a PRF pretreatment technology and a dechlorination technology, and establish a technology to utilize the materials as resources and fuels as thermal recycling of combustible wastes. The current fiscal year has performed research and development on the following themes: development of a sorting system and a crushing system in developing the pretreatment technology, whereas for the former system, sorting tests were carried out by using a vibration type wind power sorting machine and an inertia force wind power sorting machine, and for the latter system, data were obtained on the crushing characteristics; dechlorination tests, in which it was discovered that the mixing ratio of used paper in the material affects the chlorine concentration; research on combustion characteristics, in which fundamental combustion tests using a small fluidized bed, combustion tests using a bench scale fluidized bed, and stoker fired furnace combustion tests were performed; and demonstrative operation researches. (NEDO)

  2. Achievement report in fiscal 2000 on research and development project for immediately effective and innovative energy environment technologies. Development of new natural gas storage technology using adsorbents; 2000 nendo sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu jigyo seika hokokusho. Kyuchaku zai wo mochiita shinkina ten'nen gasu chozo gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    In relation with natural gas which contributes to preserving the environment and reducing dependence on petroleum, research and development has been performed on a storage system using adsorbents that allows storage of natural gas at higher density than conventional systems. This paper summarizes the achievements in fiscal 2000. In material development, the current fiscal year has performed the discussions on synthesis of three dimensional complexes. An adsorbent was synthesized successfully that has adsorption performance 2.5 times greater than the secondary complex. In developing an improved activated carbon, an adsorbent was synthesized successfully that has methane adsorption performance four times greater than the compressed gas, by using monolithic activated carbon that uses no binders. Carbon briquettes were manufactured for the basic testing equipment for fuel storage container of natural gas fueled automobiles. In the system development, installation was completed on a bench scale equipment for a gas holder and BOG treatment system, whereas engineering data were acquired from the single-column type high pressure test and two-column type constituent separation and storage test using natural gas. Selection was carried out on applicable vehicle types for the adsorption storage system for natural gas fueled automobiles, and the basic design was made for fabrication of containers of different shapes. (NEDO)

  3. Survey on the long-term energy technology strategy. 2. Survey of the basement of the industrial technology strategy settlement (Environmental basement arrangement strategy); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa. 2. Sangyo gijutsu senryaku sakutei kiban chosa (kankyo kiban seibi senryaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the Japanese industry to cope properly with the age of great competition and to secure the technology competitive force, it is indispensable to collect/analyze a lot of information and develop policies, that is, strategies, for industrial technology. For study of types of technology innovation system, a survey was conducted in FY 1999 of samples of products with comparatively high competitive force. Concept of the product concerned was examined in terms of the enterprise (person) which created the product, enterprise which commercialized it first in the world, etc. As to each of the technologies, factors to get a top share were analyzed. Based on the analyses, factors to get a large share were classified, and the relations with technology were analyzed. With 'Study of industrial technology strategy' issued in March 1999 as reference, 54 of the products of which the world share is more than 75% were extracted. In the table, about the items on creation of technology, technology was classified into the basic technology, similar technology, traditional technology, and combined technology. About the items on improvement/application, it was classified into improvement and usage development. The other items were classified into production technology, users, and development/production cooperation infrastructure. (NEDO)

  4. Fiscal 1997 survey report. Subtask 5 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen transportation/storage technology. 3. development of liquid hydrogen storage equipment); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5 suiso yuso chozo gijutsu no kaihatsu dai 3 hen ekitai suiso chozo setsubi no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the WE-NET development of large capacity liquid hydrogen storage technology, a study has been continued with a target of 50000 m{sup 3} storage development. As to the result of conceptual design and various types of the thermal insulating structure, to confirm the performance, studies were made on the thermal insulating performance test and the strength test on thermal insulating materials to be started in fiscal 1998. The large-capacity common testing equipment for thermal insulation performance to be used in and after fiscal 1998 was fabricated, and the basic performance of the equipment was confirmed by the preliminary cooling test. Further, the test pieces simulated of various thermal insulating structures were designed to study the thermal insulation performance, reformation during the test, strength, etc. It is required to solve problems such as weight reduction of test pieces, prevention of reformation, retention of vacuum, etc. In the test on strength of thermal insulating materials, a test is conducted to confirm strength of thermal insulating materials at temperatures of hydrogen by the extremely low temperature strength test equipment. The studies on test pieces to be used were summed up including the items to be paid attention to during the test because the test situation is different from that in testing metal materials. Since hydrogen is a very flammable gas, much attention should be paid to safety during the test. 13 refs., 63 figs., 32 tabs.

  5. Fiscal 1999 survey report. Survey of long-term strategy for energy technology: Volume 1 (Survey of foundation for strategy formulation for industrial technologies - strategy for environmental foundation buildup); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. 1. Sangyo gijutsu senryaku sakutei kiban chosa (kankyo kiban seibi senryaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Japan has to prepare itself to behave accurately, and to stay technologically competitive, in the severe competition age to come in which it will fail to find leaders to follow. To fulfill this goal, Japan has to collect sufficient information and analyze it relative to the current state and future prospect of industrial technologies in Japan and overseas and various factors that will influence them, and to develop industrial technology related policies based firmly on scientific and theoretical foundations to be established using the thus-acquired knowledge. Under the circumstances, a survey is conducted of innovative, technological foundations, such as industrial technology related efforts in and out of Japan. The report consists of two volumes that cover what are described below. For the survey of technology related policies pursued in various countries abroad, literature and the like are investigated concerning technology related measures, budgets, and decision making processes in America, Britain, Germany, France, and the European Union, and the results are compiled so that their systems may be compared with each other. In the survey of Japan's technology related innovative systems, case studies are made about commodities over which Japan is relatively high in competitive power. Specifically, commodities manufactured by Japan's businesses and occupying 75% or more of the global share are investigated. (NEDO)

  6. Fiscal 1997 survey report. Subtask 5 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen transportation/storage technology. 2. development of the liquid hydrogen transportation tanker); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5 suiso yuso chozo gijutsu no kaihatsu dai 2 hen ekitai suiso yuso tanker no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Technology development is being conducted for construction of the long distance transportation tanker of large quantity liquid hydrogen. In fiscal 1997, test pieces of thermal insulating materials to be planned for fiscal 1998 were designed and studied. The purpose of the test is to confirm thermal insulating performance and behaviors of each material under the temperature of liquid hydrogen. The inside of the outer tank of the experimental equipment was held at vacuum of 10{sup -6} to 10{sup -7} Torr to exclude thermal convection effects and evaluate only heat coming from heater through the test piece. The heat from the heater at the lower part of the test piece is through the test piece and makes the liquid hydrogen of the upper tank evaporate. Thermal conductivity of the test piece is calculated from the evaporation quantity. As to PUF (polyurethane foam) panels, studied were reformation preventive measures, influential evaluation of the side transfer heat quantity, and the time required for vacuuming. In the vacuum panel, study subjects were extracted on the selection of core materials, reformation preventive measures, deterioration with age, the practical manufacturing method of experimental panels, etc. As to the super insulation, subjects were studied on the performance measuring method/accuracy, measures against heat transfer from the inside of the experimental equipment, control of the vacuum degree, etc. 10 refs., 45 figs., 6 tabs.

  7. FY1998 report on the achievements on the research and development of a quickly effective and innovative energy environment technology, and development of a technology to re-use wastes as resources and fuel; Sokkoteki kakushinteki energy kankyo gijutsu kenkyu kaihatsu, kanen gomi saishigen nenryoka gijutsu kaihatsu 1998 nendo seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    With objectives to realize a recycling society and protect global environment, development will be made on solidified fuel using waste papers and waste plastics as the raw materials. This paper describes the achievements in fiscal 1998. To develop a pretreatment technology, analyses and discussions were given on functions required to separate and remove such foreign materials contained in combustible wastes as metals, ceramics, and glasses, and to pulverize the combustibles removed of non-combustible materials. A bench-scale testing equipment of 0.5 ton per hour was installed and operated on a trial basis. In order to identify dechlorination properties of waste papers and plastics to develop a dechlorination technology, basic dechlorination and pyrolysis tests were performed by using cellulose powder and polyvinyl chloride powder as raw materials. Detailed design, fabrication, installation and trial operation were carried out on a dechlorination device to be assembled into the bench-scale testing equipment. Investigations were given on the actual status of discharge and collection of waste papers and plastics to discuss the practical use of the fuel. The current status of discharge of general wastes was identified, which will be the object of the container package recycling law. The range of LCA was discussed, and technical data of wastes electric power generation were collected. (NEDO)

  8. Fiscal 1997 survey report. Subtask 5 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of hydrogen transportation/storage technology. 4. Development of various kinds of common equipment); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5 suiso yuso chozo gijutsu no kaihatsu dai 4 hen kakushu kyotsu kikirui no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    For the WE-NET development of a large-capacity liquid hydrogen pump, a magnetic bearing was studied. The test piece is a 1/3 scale model of the actual equipment, in which two radial bearings and one thrust were combined, and the impeller and turbine blade were distributed in both ends. Ti was used to the rotor and turbine, permalloy to the electromagnet, and aluminum to the case. The flotation control is made by 5-axial control, and each control coefficient was so selected that rigid body primary and secondary modes can enter into the safe domain in control. Further, as the position sensor used for control, the one used to the liquid hydrogen turbo pump of the rocket engine was made opposite and was used with the temperature characteristic compensated. The test was conducted under the extremely low temperature environment of liquid nitrogen/hydrogen temperature. It was confirmed that the sensor and electromagnet work favorably. The rotation experiment was carried out under the extremely low temperature environment and enabled the rotation up to approximately 19000 rpm. The dangerous speed of the axial rigid body is in around 6000 to 10000 rpm, and it was possible to pass this. Further improvement will be made by the tuning of control. 70 figs., 8 tabs.

  9. Achievement report for fiscal 2000 on the phase II research and development for hydrogen utilizing international clean energy system technology (WE-NET). Task 9. Development of liquid hydrogen transportation and storage technologies - 1; 2000 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) dai 2 ki kenkyu kaihatsu. Task 9. Ekitai suiso yuso chozo gijutsu no kaihatsu - 1

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    This paper describes the achievements in fiscal 2000 from the development of liquid hydrogen transportation and storage technologies. Discussions were given on the following three types of specimens as the heat insulation performance test structures: the vacuum panel type (polyurethane foam coated with SUS sheet, while the inside is kept in the vacuum state); the solid vacuum type (combination of polyurethane foam with vacuum heat insulation); and the powder under normal pressure type (a structure in which the ambient of powder pearlite heat insulating material becomes the atmospheric pressure, whereas a SUS case is set up to separate vacuum layer of the test apparatus from atmosphere layer of the specimen, with the SUS case filled with pearlite). Adding the two types of specimens used in the previous fiscal year, five test specimens in total were discussed on the result of the performance tests to advance the database management. As a low temperature strength test for the insulating materials, the compression test was performed on a microsphere being a kind of solid vacuum (normal pressure) heat insulating materials at room temperature, the liquid nitrogen temperature and in liquid hydrogen atmosphere. The compression strength under liquid hydrogen is 1,044 MPa, which is two times greater than the normal temperature strength of 496 MPa, representing the compression strength rising in proportion with temperature drop. Problems were extracted in developing a small capacity liquid hydrogen transportation and storage system. (NEDO)

  10. Industrial science and technology research and development project of university cooperative type in fiscal 2000. Report on achievements in semiconductor device manufacturing processes using Cat-CVD method (Development of technology to rationalize energy usage); 2000 nendo daigaku renkeigata sangyo kagaku gijutsu kenkyu kaihatsu project. Cat-CVD ho ni yoru handotai device seizo process seika hokokusho (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    The catalytic chemical vapor deposition (Cat-CVD) method is a low-temperature thin film depositing technology that can achieve improvement in quality of semiconductor thin films and can perform inexpensive film deposition in a large area. This paper summarizes the achievements in fiscal 2000 in the demonstrative research and development theme of the present project, centering on the following five areas: 1) discussions on application of the Cat-CVD method to the mass production process for gallium arsenide integrated circuits, 2) studies on the possibility to apply the Cat-CVD method to the process to fabricate nitrided silicon protective film for ferroelectric memory devices, 3) formation of nitrided silicon films for silicon integrated circuits by means of the Cat-CVD method, and development of a chamber cleaning technology, 4) fabrication of high-mobility poly-crystalline silicon thin film transistors formed by using the Cat-CVD method and large particle size poly-crystalline silicon films by using the catalytic chemical sputtering process, and 5) discussions on properties of amorphous silicon thin film transistors formed by using the Cat-CVD method and formation of large area films by using a catalyst integrated shower head. (NEDO)

  11. Report on fiscal 1999 results of R and D on industrial science and technology. R and D on 'frontier carbon technology' (development of technology for rationalizing use of energy); 1999 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    R and D was conducted on original processing technology for electrically functional materials as a R and D project on frontier carbon technology, with the results for fiscal 1999 compiled. In the development of film forming technology using a large morphology control film forming device, the device was introduced this year, with film forming conditions probed. In the development of large size diamond synthesis process, single crystal synthesis and evaluation were carried out using an existing microwave plasma CVD reactor, with a study of design made for the device for obtaining a target 16 mm diameter single crystal. In the development of technology for oriented diamond growth on a platinum-based metallic base plate, research was done for controlling generation of grain boundary in a diamond film, through the improvement of orientation and the reduction of non-oriented grain density of the diamond nucleated on the base plate. The studies on control technology of surface-interface and electron emission characteristics were conducted on such subjects as fabrication technology of diamond for field emission, characterization of field emission, and photoelectron emission spectroscopy of diamond. (NEDO)

  12. Report on achievements in fiscal 1999 on research and development of the industrial and scientific technology. Research and development of synergy ceramics (development of a technology to rationalize use of energies); 1999 nendo sangyo kagaku gijutsu kenkyu kaihatsu seika hokokusho. Synergy ceramics no kenkyu kaihatsu (energy shiyo gorika gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper summarizes the achievements in fiscal 1999 on research and development of a technology to use synergy ceramics as a material, its application technology and the common base technology. In the research of high-function active materials, development was made on catalyst and electrode materials having the selection, separation and rinsing functions, and discussions were given on materials for thermoelectric conversion of oxides. In the research and development of new thermoelectric conversion ceramics materials, searches were made on cobalt and nickel containing compound oxides. In the development of corrosion-resistant electrochemical cell materials, the honeycomb type was devised, and a technology was developed to form honeycombs laminated with different materials. In developing self-lubricating functional materials, silicon nitride with solid lubricant of MoO{sub 3} dispersed on the surface layer was developed, wherein tribological characteristics were evaluated. In developing ultra-smooth low friction materials, studies were carried out on reducing friction by controlling silicon nitride and its surface structure, placing lifter shims in an automotive engine as the application object. The joint research with the National Research Institute performed evaluations on the compound function manifestation process. (NEDO)

  13. Report on research achievements in fiscal 1999. Research and development of an ultra-high density electron SI technology (development of a technology for energy use rationalization); 1999 nendo chokomitsudo denshi SI gijutsu no kenkyu kaihatsu energy shiyo gorika gijutsu kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-05-01

    A high-density information network society is going to be realized in the 21st century. Information communication devices used therein are demanded of having high speed and high performance including acoustic and image digital processing, reduced size and weight, and low electric power consumption. While explosion in increase is estimated in the quantity of information handled by these information communication devices, there is a trend that the speed increase in CPU cannot follow the quantity increase. The present proposal is intended to make drastic performance enhancement by using the electron SI (comprehensive mounting) technology which includes making the LSI chips three dimensional and compounding light and electric power mounting, as well as design optimization. The present research and development has an objective to integrate the following three elements to achieve an ultra-high density electron SI technology: (1) a three-dimensional lamination technology making shortest wiring between LSI chips possible, (2) a light and electric power compounded mounting technology making high speed and large capacity transmission inside a board possible, and (3) optimal wiring structure design to suppress unnecessary electromagnetic radiation caused by increasing signal speeds. The research plan period lasts for five years. This paper reports the progresses in each theme in fiscal 1999. (NEDO)

  14. Fiscal 2000 survey report. Survey of long-term energy technology strategy and the like (Research on actualities of Japanese industries' research and development potential); 2000 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. Sangyo gijutsu senryaku sakutei kiban chosa (Nippon kigyo no kenkyu kaihatsuryoku no jittai ni kansuru chosa kenkyu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    For working out propositions on what the country should do and on what improvement industries should make for the strengthening of industries' competitive power on the market, analyses were conducted into the objects of research and development, organizations engaged in research and development activities, methods of evaluation, and the like. In concrete terms, studies were made on industries' roles in research and development activities and on the actualities of basic research and development potential, and then a survey was conducted through questionnaires and interviews about (1) tasks relating to corporation management and research and development potential, (2) development of research dedicated talent and its fluidity, and (3) problems feared to get worse in the future. Questionnaires were sent to 217 corporations or 577 people of whom 37.6% responded. Each item is described below. Under item (1), it is pointed out that basic research has shrunk as a whole, that pressure is on the increase urging that research directly increase profit, and that theme selection is made to match the business model. Under item (2), it is stated that post-doctorate researchers' knowledge is respected but that recruitment is another matter, and that fluidity of researchers between corporations will increase. Under item (3), it is pointed out that researchers are increasingly inferior in quality and that brain drain out of Japan is feared. (NEDO)

  15. Fiscal 1999 survey report. Survey of long-term strategy for energy technology: Volume 1 (Survey of foundation for strategy formulation for industrial technologies - strategy for environmental foundation buildup); 1999 nendo choki energy gijutsu senryaku nado ni kansuru chosa hokokusho. 1. Sangyo gijutsu senryaku sakutei kiban chosa (kankyo kiban seibi senryaku)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Japan has to prepare itself to behave accurately, and to stay technologically competitive, in the severe competition age to come in which it will fail to find leaders to follow. To fulfill this goal, Japan has to collect sufficient information and analyze it relative to the current state and future prospect of industrial technologies in Japan and overseas and various factors that will influence them, and to develop industrial technology related policies based firmly on scientific and theoretical foundations to be established using the thus-acquired knowledge. Under the circumstances, a survey is conducted of innovative, technological foundations, such as industrial technology related efforts in and out of Japan. The report consists of two volumes that cover what are described below. For the survey of technology related policies pursued in various countries abroad, literature and the like are investigated concerning technology related measures, budgets, and decision making processes in America, Britain, Germany, France, and the European Union, and the results are compiled so that their systems may be compared with each other. In the survey of Japan's technology related innovative systems, case studies are made about commodities over which Japan is relatively high in competitive power. Specifically, commodities manufactured by Japan's businesses and occupying 75% or more of the global share are investigated. (NEDO)

  16. FY 1998 Annual report on research and development of industrial science and technology. R and D of carbon-based high-performance materials technology (R and D for rationalization of energy consumption); 1998 nendo tansokei kokino zairyo gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-09-01

    This report summarizes the FY 1998 research and development results of carbon-based high-performance materials technology. For (control technology of morphology and electrical conduction), a large-sized morphology controlling film-making apparatus was used, to confirm synthesis of crystalline diamond films. For research on growth of large-sized single-crystal diamond, the simulated results of the vapor-phase reactions and gas flow in a plasma were compared with the observed ones, to collect the data necessary for designing a high-speed homoepitaxial growth apparatus. For R and D of heteroepitaxial growth of thin diamond films, highly single-crystalline thin platinum films were successfully formed on a sapphire substrate. For (control technology of surface-interface and electron emission characteristics), the tests were conducted using newly introduced apparatuses, an (electron emission analysis/evaluation apparatus), (high-quality carbon-based thin film synthesizing apparatus) and (element processing/treatment apparatus). It is found that electron emission efficiency is greatly improved when the substrate with diamond particle seeds is plasma-treated under specific conditions. (NEDO)

  17. Fiscal 1997 survey report. Subtask 6 (hydrogen utilization worldwide clean energy system technology) (WE-NET) (development of technology of low temperature materials); 1997 nendo seika hokokusho. Suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 6 teion zairyo gijutsu no kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    The paper described the results of the development of technology of low temperature materials in the fiscal 1997 WE-NET. Using experimental equipment for materials under the atmosphere of liquid hydrogen, an experiment on mechanical characteristics under the liquid hydrogen atmosphere (20K) was conducted of the base materials of candidate steels (SUS304L, SUS316L and A5083). In material evaluation experiments (tension/fracture toughness/fracture tests), characteristic behaviors of the materials were shown which are different from those shown in the environment of liquid He (4k), etc. Even if the amount of {delta} ferrite in the metal welded of the stainless steel is small, approximately 1%, the degradation of low temperature toughness occurred. Welded joints of stainless steel by submerged arc welding and MAG welding were in now way inferior in tension characteristic to those by TIG welding, but were inferior in toughness ranging from room temperature to extremely low temperature. As to aluminum alloys, materials excellent in extremely-low temperature toughness were able to be found. Under the low temperature hydrogen gas atmosphere, the lower the strain rate is, the higher the hydrogen brittleness susceptibility is around 220K (extremely large hydrogen brittleness temperature) (SUS304L). In the hydrogen gas of 100 atm, hydrogen invades the material at 100degC, but does not at 77k. 38 refs., 173 figs., 48 tabs.

  18. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of tanker for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso yuso tanker no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the WE-NET project, the tanker for liquid hydrogen transport was studied. In fiscal 1996, some experiments and numerical analyses were proposed which are necessary to solve technological issues extracted in fiscal 1995 for heat insulation structure. The issue was roughly classified into vacuum and non-vacuum insulation, and their basic functions and required performance were arranged. Boil-off rate of 0.2-0.4%/d was targeted. The insulation system which applies polyurethane form (PUF) to tank surfaces and injects atmospheric N2 gas into the surrounding hold space, could achieve the targeted insulation performance by PUF of 1m in thickness. The system of vacuum panel insulation and atmospheric N2 gas injection into a hold space required the panel of 500mm in thickness because of the large effect of metallic outer panel material. The system of vacuum hold and PUF panels was faced with the essential issue for realizing and maintaining vacuum hold. The super insulation system featured by layered insulation materials and vacuum layer spaces was also strongly affected by degree of vacuum. 23 figs., 8 tabs.

  19. Fiscal 1999 industrial science and technology R and D (industrial-academic) project report. R and D on technologies for creating bioaffinity molecules using submicron beads (Development of practical technologies for energy saving); 1999 nendo biryushi riyogata seimeitai ketsugo busshitsu nado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 R and D result on technologies for creating bioaffinity molecules using submicron beads. By improving particle production, favorable SGNEGDE particles for drug fixation were produced on a scale 10 times as large as previous one. Various functional groups were obtained for particles immobilizing ligands. Magnetic purification was attempted by using new magnetic polymer particles. Synthesis of particle unsusceptible to non- specific bonds, and analysis of its modified surface properties were attempted. Reversible attachable-detachable surface coat was obtained by immobilizing boric acid to glycol group on affinity latex SG particles. The experiment result on affinity latex for detecting one-point mismatched DNAs showed the dependence of DNA hybridization on shearing resistance. To construct the library of new substances reacting with bio-receptors, solid phase synthesis of anti- tumor heterocyclic compounds was analyzed. The library of the pharmacology of new lead compound such as sugar moiety was also constructed. Study was made on attachment of alkaloid to a solid phase, synthetic reaction on a solid phase and library construction. (NEDO)

  20. International Clean Energy System Using Hydrogen Conversion (WE-NET). subtask 5. Development of hydrogen transport/storage technology (development of storage facility for liquid hydrogen); Suiso riyo kokusai clean energy system gijutsu (WE-NET). subtask 5. Suiso yuso chozo gijutsu no kaihatsu (ekitai suiso chozo setsubi no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    As a part of the WE-NET project, the storage facility for a large amount of liquid hydrogen (LH) was studied. Gasification loss caused by heat input of LH delivery pumps was studied for liquefaction and power generation bases assuming an pump efficiency of 70%, and the total heat and mass balance such as interface conditions for calculating the amount of boil-off gas was reviewed. The target storage capacity of 50,000m{sup 3} was reasonable, however, the performance of loading arms should be examined. The capacity around 5,000m{sup 3} of coastal localized bases was reasonable for control delivery loss caused by coastal tanker or LH container system to 2.6%. The capacity of 500m{sup 3} was suitable for inland bases, resulting in the loss of 1.2%. The concept design of the storage tank of 50,000m{sup 3} extracted confirmation of low-temperature characteristics of adiabatic materials and structures, and development of leakage inspection technology and vacuum holding technology as issues. The concept design of the underground storage tank showed that the material specifications for LNG ones are applicable to it by using proper adiabatic structures. 4 refs., 72 figs., 27 tabs.

  1. Achievement report for fiscal 1998. Research and development of technologies for creating new bioaffinity molecules using submicron beads (Energy use rationalization related technology practicalization); 1998 nendo biryushi riyogata seitai ketsugo busshitsunado sosei gijutsu no kenkyu kaihatsu seika hokokusho. Energy shiyo gorika kankei gijutsu jitsuyoka kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    In the effort to develop chemical substance/bioreceptor analysis technology using submicron beads, polystyrene core/polyglycidyl methacrilate beads are used in a study started about a detachable spacer using newly developed fixation technology. In the development of bioaffinity chemical substance refining technology, two kinds of sugars and several kinds of aromatic aldehydes serve as building blocks in the construction of a library, and studies are made of analyses using liquid chromatography and mass spectrography. In the development of novel substance creation technology based on information on the analysis of chemical substance/bioreceptor, in an effort at developing technologies for creating novel function provided chemical substances, heterocyclic compounds, alkaloids, and sugar compounds are selected and their syntheses in the liquid phase and solid phase are studied, which is again for the construction of a library. (NEDO)

  2. Achievement report for fiscal 1998 on World Energy Network (WE-NET). Subtask 5. Development of hydrogen transportation and storage technologies (development of liquid hydrogen storage facilities); 1998 nendo suiso riyo kokusai clean energy system gijutsu (WE-NET) subtask 5. Suiso yuso chozo gijutsu no kaiahtsu (ekitai suiso chozo setsubi no kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1999-03-01

    An insulation structure suitable for large tanks was tested for insulation capability and strength at the liquid hydrogen temperature for the development of liquid hydrogen storage facilities. For the insulation test, a specimen was built of a porous solid material, and the specimen was given an additional duty of serving a test of a high temperature plate that was to impose loads on the specimen. The test conditions were not met, however, with too much variation in presence in temperature distribution. For the structural material compressive strength test, a method was worked out involving a hard urethane foam material specimen in liquid hydrogen, and was implemented. It was found that the specimen fracture that occurred was in the form of the collapse of the loaded surface. Tests were conducted at three temperatures, which were the normal temperature, the liquid nitrogen temperature, and the liquid hydrogen temperature, and compressive strength was determined for each of the three cases. No great difference in strength resulted from the difference between the two low temperatures. As for compressive strength at low temperatures, it was found that the strength was approximately two times greater than at the normal temperature. The above findings indicate that hard polyurethane foam is on the safe side when it is designed for the normal temperature. (NEDO)

  3. Achievement report for fiscal 1976 on Sunshine Program. Research on hydrogen production technology (Research on hydrogen production technology using thermochemical method); 1976 nendo suiso no seizo gijutsu no kenkyu seika hokokusho. Netsukagakuho ni yoru suiso seizo gijutsu no kenkyu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1977-03-01

    This report covers part of the efforts to develop new hydrogen production technologies. Out of many processes involving Cu-halogen and alkali carbonate-iodine systems proposed as novel thermochemical processes, after they are compared with each other, a process of a sodium carbonate-iodine system with nickel in between is chosen. The chosen process is deemed to be the most excellent among the processes disclosed up to fiscal 1975. A feasibility study is conducted for the chosen process from the viewpoint of reaction rate, separation of reactive substances from each other, method for reaction manipulation, materials for device constitution, and thermal efficiency. As for the measurement of reaction rate for each unit reaction, basic reaction data are determined centering about the nickel iodide decomposition reaction and the sodium iodide carbonation reaction, and then reaction conditions which are roughly satisfying are obtained. A larger reaction unit is built in which the amounts of substances that come into reaction are approximately 10 times larger than those in the ones used in basic experiments. The progress of reactions is observed in the reaction unit, with the size enlarged in preparation for future construction of still larger reaction units. Methods for selectively isolating hydrogen out of gases ensuing from the decomposition are evaluated from the viewpoint of energy efficiency. In the selection of a reaction manipulation method, a single unit reaction process is advocated, and its thermal efficiency is estimated. (NEDO)

  4. FY 2000 survey on technical trends. Survey of technical trends on materials for heightening of performance for power generation facility use; 2000 nendo gijutsu doko nado chosa. Hatsuden shisetsuyo koseinoka zairyo ni kakawaru gijutsu doko nado chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    As to high performance/high function plastic materials used in power generation facilities, technical trends were surveyed on the recycle situation and recycle R and D to study the subjects to be solved. For wire covering materials, vinyl chloride, polyethylene, rubber, etc. are used, and the recycle of resin has not been advanced. Concerning the generation of waste plastic, the existence of a lot of plastics different in characteristics makes the recycle difficult. As to the use of waste plastic as resource, the material recycle and recovery of combustion energy are being made, but only a part of the plastic is reused as chemical raw materials. Relating to the R and D of the chemical recycle technology, there are sample studies on the pyrolysis of polyolefine, dechlorination of chlorine base resins, etc. Recently, the following have been made public: proposal of depolymerization monomer based on the cyclic monomer, study of liquefaction of approximately 100% of the thermosetting resin, approach to the solvolysis by supercritical solvent. (NEDO)

  5. NEDO Forum 2001. Session on industrial technology development (Future of thing making and manufacturing/processing technologies); NEDO Forum 2001. Sangyo gijutsu kaihatsu session (monozukuri seisan kako gijutsu no mirai)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-09-20

    The presentations made at the above-named session of the NEDO (New Energy and Industrial Technology Development Organization) forum held in Tokyo on September 20, 2001, are collected in this report. In a lecture entitled 'History of thing making,' the roles played by the now-defunct National Testing Laboratory and Industrial Test and Research Center were described and strategy for future development was predicted. In a lecture entitled 'Thing making and international apprentices competition,' apprenticeship training in practice at Denso Systems Corporation was presented. In a lecture entitled 'Key technology in thing making: outlook of metal mold industry,' shift in Japanese manufacturers' paradigm and change in metal mold marketing were explained, and the importance of reaching for the first position in the world in some specific fields or of expanding the scope of work in the entire value chain was stressed. In a lecture entitled 'Digital meister project: Aiming at amalgamation of IT (information technology) and MT (manufacturing technology),' database construction in the manufacture of metal molds, introduction of knowledge management systems, and development of CAD/CAM/CAE (computer-aided design/computer-aided manufacturing/computer-aided engineering) were discussed. (NEDO)

  6. Fiscal 2000 research report on the research on materialss with functions enhanced by microcapsulation technology; 2000 nendo microcapsul ka gijutsu ni yoru kokinoka zairyo gijutsu no chosa kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-03-01

    Research is conducted to create materialss equipped, thanks to microcapsulation, with a noise stopping function, vibration damping function, moisture adjusting function, electromagnetic shielding function, and the like, and usable as structural elements as is, that is, materialss known as 'interactive materialss.' For the development of an interactive materials, it is important to incorporate an element, which interacts with external energy, into the materials. A system using interactive materialss when embodied will ensure a safer and more comfortable daily life space. Taking this into consideration, in this fiscal year, studies are made about the technical representation of problems and troubles that jeopardize the safety and comfort of the daily life space, establishment of standards in this connection, interactive features to be realized using microcapsules, possibility of novel interactive characteristics using the same, techniques for the systematization of microcapsules as industrial materialss, techniques for assessing and analyzing materialss characteristics, simulation or the like of a safe and comfortable space using interactive materials-aided systems, and so forth. (NEDO)

  7. FY 1998 achievement report on the photon measuring/processing technology (R and D of the photon measuring/processing technology); 1998 nendo foton keisoku kako gijutsu seika hokokusho. Foton keisoku kako gijutsu no kenkyu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    In this project, the survey/arrangement were made of the trend of the recent technology such as photon (laser) measuring/processing/generation and a possibility of adopting the photon technology to the field except measuring/processing, to clarify technical subjects for establishing/commercializing the photon technology. Also for the purpose of reducing the energy cost by improving the performance of laser processing device, prolonging the life and reducing the operational cost, the development of the following were carried out: (1) high efficiency laser processing device. (2) high conversion efficiency laser diode. In (1), a laser generating device with Yb:YAG crystal as oscillating medium was trially manufactured, and the power of 35W and optical-optical conversion efficiency of 7.1% were obtained. A comparison was also made between Yb:YAG laser and Nd:YAG laser, and made it clear that as the industrial use high power laser, Nd:YAG laser has the advantage over the other. In (2), the development was made of technology for simultaneous uniform growth of more than one LD crystal wafers with high conversion efficiency and technology for evaluation. Namely, the high uniformity crystal wafer with variations among wafers of {+-}4% was obtained using the introduced high efficiency crystal growth device and high efficiency thin film evaluation device. (NEDO)

  8. Fiscal 1997 report on technological results. R and D on micromachine technology (Development of micro-factory technology); 1997 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-03-01

    Activities are conducted in search of a micromachine system in which devices and equipment relating to machining, assembly, transportation, inspection, etc., in use for a manufacturing process are integrated in a narrow space, for the purpose of conserving energy through the miniaturization of the process of manufacturing small industrial products. With the activities in the two fields of (1) R and D of systematization technology (experimental system for micro fabrication/assembly) and (2) comprehensive investigation and research, examination on detailed specification for the experimental system was carried out, as were the examination of element technologies, element device operating experiments, technological investigation, etc.. In (1), sophistication of the element technologies was contrived that were required for realizing each experimental system, while the detailed specification of each experimental system was decided. Further, a part of the element devices was experimentally manufactured, with the basic functions verified. In (2), research studies were compiled on radio interference for example in the case where various devices were integrated and highly densified through the formation of a micro-factory; also compiled was a joint research with Agency of Industrial Science and Technology, a research conducted for the purpose of building the conception of the micro-factory. (NEDO)

  9. FY 1994 Report on the technical results. Research and development of micromachine technologies (Development of highly functional maintenance technologies for power plants); 1994 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-09-01

    This research and development project is aimed at development of the technologies for the micromachines provided with maintenance functions, e.g., for examination and maintenance of abnormal conditions in heat exchangers, piping systems or the like. The initial target is set at establishment of basic technologies for the micromachines, in consideration of the available technologies. The R and D activities are directed to (1) microcapsules for, e.g., micro power generators, (2) mother machines having controlling and instructing functions, (3) non-cabled examination modules, (4) cabled examination modules, and (5) total systems. The item (1) involves the micro power generators, and mechanisms of signal transmission, flaw finding and driving/suspension; the item (2) mechanisms of micro-optics and connection, group controlling, microbatteries, action type controlling, and artificial muscles; the item (3) expansion/contraction type transfer mechanisms, light energy supply, micro visual sensation, function connection, and concerted controlling; the item (4) tubular manipulators, and mechanisms of light-aided power generation and voltage elevation; and the item (5) maintenance and micromachine systems. (NEDO)

  10. Report on achievements in fiscal 1999. Research and development of micro-machine technologies (development of micro-factory technologies); 1999 nendo micro machine gijutsu no kenkyu kaihatsu seika hokokusho. Micro factory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    With an objective to achieve energy saving by micronizing the manufacturing processes of small industrial products, this research and development is intended to establish technologies to realize a micro-machine system, in which devices for processing, assembly, transportation and inspection used in the manufacturing processes are unified and incorporated in narrow spaces. Fiscal 1999 has performed, on the items of (1) research and development of the systematizing technologies and (2) comprehensive surveys and researches, with respect to the development of the first prototype system, and fabrication on the trial basis of devices to be mounted on the second prototype system, and discussions on further functional enhancement of the different devices. As a result in the research of the systematizing technology, the first prototype system was developed, that unifies the base unit fabricated in fiscal 1998, the electrolysis processing device, the fluid feeding device, the micro-arms, the coating device, the transportation device, and the environment recognizing device. The basic performances of the individual devices on the first prototype system were verified. Based on the result of this function verification, optimal design and fabrication on the trial basis of the devices mounted in the second prototype system were performed, and discussions were given on the further function enhancement in each functional device. (NEDO)

  11. Fiscal 1999 research report. Research on photonic measurement and processing technology (Development of advanced maintenance technology for power plant facilities); 1999 nendo foton keisoku kako gijutsu seika hokokusho. Hatsuden shisetsuyo kokino maintenance gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This report summarizes the fiscal 1999 research result on R and D of measurement technology, laser welding and surface treatment technology, and generation technology of photon beam, for improvement of the quality and maintenance efficiency for power plant facilities. In the study on fabrication of functional micro-composite circuits, the equipment for forming circuits on substrates by carrying particles with gas was developed whose geometric standard deviation is 1.17 for 26nm particles. In the study on gas concentration measurement technology, development of the variable-wavelength laser beam source for measurement, fabrication of thin films by epitaxial growth equipment, and computer simulation of sensitivities for quantum IR photo- detectors were promoted. In the study on photon wavefront compensation device technology, the technology for fabricating such device with (411)A surface orientations and asymmetric quantum well structures was developed. In the study on high-sensitivity detection technology using short- wavelength photon, to develop a high-energy resolution fluorescent X-ray detector, favorable electric properties of superconducting X-ray detecting devices were confirmed at nearly 0.1K. (NEDO)

  12. Achievement report for fiscal 1996 on the research and development of micromachine technology. Development of microfactory technology; 1996 nendo micromachine gijutsu no kenkyu kaihatsu seika hokokusho. Microfactory gijutsu kaihatsu

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    The goal is to save energy and minimize the working space by constructing a manufacturing system comprising various micromachines with their dimensions fit for parts and products they handle. Development continues relative to microprocessing (electrolysis, and optical processing) and microscopic liquid operation (micropump, and part holding device). Under research in relation to the assembly process are a micro-arm to handle tiny parts and precision techniques for interfitting within a very small microfactory, a piezoelectric actuator for microscopic position adjusting, and ultraprecise microprocessing techniques indispensable for their manufacture. Also under research are the incorporation of optically driven microdevices developed before the preceding fiscal year into a microfactory and the study of microservo actuators capable of sophisticated positioning and velocity control. Concerning the microscopic transport system to deal with microscopic parts and products, studies are under way so as to embody systems driven by actuators of the electromagnetic type and electrostatic type. In this paper, reference is made to inspection techniques and comprehensive investigations. (NEDO)

  13. Energy evaluation

    International Nuclear Information System (INIS)

    Anon.

    2005-01-01

    These 8 charts bring information on with the primary energy consumption, energy indicators, energy bill, prices and electric power, petroleum, natural gas and solid mineral fuels from January 2003 to January 2006. (A.L.B.)

  14. Energy Drinks

    Science.gov (United States)

    ... R S T U V W X Y Z Energy Drinks Share: © Thinkstock Energy drinks are widely promoted as products that increase ... people has been quite effective. Next to multivitamins, energy drinks are the most popular dietary supplement consumed ...

  15. Energy Models

    Science.gov (United States)

    Energy models characterize the energy system, its evolution, and its interactions with the broader economy. The energy system consists of primary resources, including both fossil fuels and renewables; power plants, refineries, and other technologies to process and convert these r...

  16. Energy, tourism

    OpenAIRE

    Frantál, B. (Bohumil)

    2015-01-01

    The chapter provides a general definition of energy and resume the role and environmental impacts of tourism as one of the largest global industries and energy consumers.Then the energy tourism nexus is conceptualized from three perspectives: The first is energy as a driver of tourism. The second is energy as a constraint of tourism. The third is energy as an attraction and object of tourists´interests.

  17. FY 1974 report. Study on hydrogen combustion technology; 1974 nendo suiso nensho gijutsu ni kansuru kenkyu hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1975-03-01

    In the use of hydrogen as fuel, there is the problem on NOx emission. The amount of NOx emission is not as much as in the use of coal or oil, but is more than in the use of natural gas or town gas. However, it can be said that hydrogen is an ideal fuel if considered that it does not emit other air pollutants such as CO, HC and soot/dust which are usually associated with hydrocarbon base gas fuels, and also that hydrogen forms a circulation system which is ecologically sound. The flame of hydrogen is non-luminous, but the flame temperature is high. The formation of NOx depends strongly upon the flame temperature, and therefore, in the design of hydrogen burner, it is necessary to well mix it with air and to avoid the production of the local high temperature region. Further, when using hydrogen to large boiler, the combustion technology to control NOx reduction is needed. About the hydrogen flame, the matter to be noticed is an experimental result that NOx reduction was observed by adding trace ammonia to hydrogen gas. If this method can be successful, NOx can be reduced with no increase in fuel consumption. It leads to hydrogen's reaching a position of clean energy. (NEDO)

  18. Survey of regulations accompanied with isolation technology of carbon dioxide; Nisanka tanso no kakuri gijutsu ni tomonau hokisei no chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Regulations, conventions and agreements relating to the discharging liquefied carbon dioxide (CO2) into the bathypelagic zone from a cruising ships are investigated. The ocean storage of CO2 is not specifically prohibited by law, but must be regulated on a global scale because such treatment may impact the marine environment. In principle, treatment with impact on the nature is prohibited. Laws of environmental conservation are completed in European, Asian, and Pacific countries, which join international conventions and committees with high interests. It is suggested that the engineering technique of the storage should be improved to observe regulations and that an impact assessment for the ocean storage should be carefully conducted in full understanding of the basic premise of the regulatory systems or organizations. Furthermore, it is significant to study on the possible effect of the ocean storage of CO2 on global warming and life-cycle assessment inventory analysis, namely the balance of the energy budget between the separation and the ocean storage of CO2. 23 refs., 7 figs., 6 tabs.

  19. Research trend survey on the stable isotope utilization technology; Antei doitai no riyo gijutsu ni kansuru kenkyu doko chosa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    This report reviews the activities and the trends in the area of the stable isotope use attracting attention recently. In the medicine and clinical treatment sector, the remarkable trends are the extension of {sup 13}C use. The breath test and the magnetic resonance spectroscopy (MRS) diagnosis have been developed as inspection methods. It is noted that investigation has been initiated on the magnetic resonance imaging (MRI) using {sup 3}He and {sup 129}Xe for the lung imaging. In the organic chemistry and biochemistry sector, the stable isotopes are used for analyzing the structures of complicated natural compounds and materials relating to life science and for analyzing the chemical reaction mechanism of organic compounds. In the nuclear energy sector, {sup 10}B and {sup 7}Li have been used as neutron absorption materials and pH neutralizing reagent, respectively. In the analysis and measurement sector, the process of isotopic dilution is used for the environmental analysis of trace elements including harmful substances. Among various separation methods of isotopes, well studied uranium enrichment processes and deuterium separation processes are described. Separation of {sup 15}N by ion exchange resin method and plasma ion cyclotron resonance (ICR) isotope separation have been studied, recently. 133 refs., 53 figs., 7 tabs.

  20. Research report of innovation of industrial technology in FY 1996; 1996 nendo sangyo gijutsu no innovation chosa hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-03-01

    Remarkable innovations of the Japanese industry in various fields have been extracted and evaluated during the 50 post-war years. In this report, a method of capturing the innovations of industrial technology is examined. It is essential to clarify the social role of industrial technology, and the original views of this research are indicated by focusing on the innovation process in order to clarify the connections between those of mutual industry, technical management, man-power, and unique Japanese technology. The innovations achieved by the Japanese industry during post-war 50 years are classified into eight categories, i.e., automobiles, iron, aero-space/railways, machines, national land/energy, chemicals/fine ceramics, electronics/information/communication, and life, to clarify the technological progress in each field. In Japan, the industrial technology has been developed with learning from fundamental researches in Europe and the USA. In the future, it is necessary to independently develop industrial frontier. 4 figs., 47 tabs.

  1. Research of fluidized bed cement clinker sintering system by pilot plant; Ryudosho cement shosei gijutsu no kaihatsu. 7

    Energy Technology Data Exchange (ETDEWEB)

    Sugiyama, T [Center for Coal Utilization, Japan, Tokyo (Japan); Sato, N; Hashimoto, I; Nakatsuka, M [The Cement Association of Japan, Tokyo (Japan)

    1996-09-01

    While a cement manufacturing process generally performs sintering by using a rotary kiln, a development work has been carried out as a subsidy operation of the Agency of Natural Resources and Energy on a cement sintering technology using a fluidized bed consisted of two furnaces: a jet flow bed granulating furnace and a fluidized bed sintering furnace. This paper reports the results of tests and researches performed during fiscal 1995. A plant with a scale of 20 ton-a-day production started in 1993 after having gone through bench scale tests. The year 1995 conducted by August its performance evaluation, review of the operation method and the safety criteria, and generalization of the tests. A multi-stage cyclone system has been employed in the preheating equipment for cement material powder. A number of improvements have been realized in the aspects of construction and operation, such as stabilization of dust collecting efficiency by employing a high-efficiency type cyclone, and operation with reduced pressure variation. Based on these results, a construction had been progressed in parallel on a new plant upscaled to 200 ton-a-day production. The new plant was completed in December, 1995. 9 figs., 8 tabs.

  2. Practical use technology of coal ash (Poz-O-Tec); Sekitanbai no yuko riyo gijutsu (POZ-O-TEC)

    Energy Technology Data Exchange (ETDEWEB)

    Konno, K [Center for Coal Utilization, Japan, Tokyo (Japan); Saito, Y [Mitsui Mining Co. Ltd., Tokyo (Japan); Nagaya, Y [Mitsui Construction Co. Ltd., Tokyo (Japan)

    1996-09-01

    In order to utilize more effectively coal ash whose generation amount is increasing year after year, studies have been made on a technology to manufacture and utilize a high-strength substance solidified under normal temperature by utilizing hydration reaction of pozzolan system (Poz-O-Tec). The study works have been done as a subsidy operation of the Agency of Natural Resources and Energy, and were completed in fiscal 1995. Poz-O-Tec is a wet powder made of coal ash and stack gas desulfurization sludge (gypsum) added and mixed with lime and an adequate amount of water, which solidifies by hydration as pozzolan does. The same method as used for ordinary sands may be used as the basic application method. Because this is the material whose strength increases after construction, thickness of construction may be reduced smaller than in constructions using soils and sands. Test constructions of about sixty cases have been carried out to date, typically represented in use as a road bed material, banking, and a base material for water-barrier gutters. High-strength solid material which is stable under normal temperature may be obtained by adjusting calcium content. As a result of its effectiveness in practical use having been verified, a certificate of technological judgment has been issued for the material by the Civil Engineering Research Center. 3 refs., 11 figs., 2 tabs.

  3. 17th Symposium of NEDO projects. Industrial technology subcommittee; Sangyo gijutsu bunkakai. Dai 17 kai jigyo hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-09-01

    Described herein are the reports presented to the industrial technology subcommittee, 17th symposium of NEDO projects. For development of high-efficiency industrial furnaces by high-temperature air combustion (including regenerative combustion), high-temperature air above 1000 degrees C is used, where carbon dioxide and NOX are possibly abated by 30% or more and 50%, respectively. The worldwide development is also described. For production of high-function ceramic materials at low temperature, the soft solution process is proposed for the in-situ production of these ceramic materials from the aqueous solution without using high temperature or high energy. For example, the high-functional ceramic material can be produced in-situ on a substrate by reacting the highly active aqueous solution with the substrate by a combination of, e.g., the hydrothermal and electrochemical reactions, without needing post-treatment under heating. For the marine biological technologies, deposition of living organisms is described. A geodome is developed for utilizing very deep (50m or deeper) underground spaces. It is a dome-shaped space supported by no strut, having dimensions of 50m in diameter and 30m high not to affect the surrounding environments, e.g., underground water. The techniques for creating advanced functional materials are developed by combining, e.g., laser, plasma, ion and magnetic field in diversified manners. (NEDO)

  4. NEDO industrial technology subcommittee. 18th project report meeting; NEDO sangyo gijutsu bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    In relation to NEDO's (New Energy and Industrial Technology Development Organization) research and development to put to practical use a ceramic substrate material which is sinterable at low temperature and capable of high heat radiation, a report is delivered on a low-temperature continuous baking process that realizes the mass production of aluminum nitride substrates high in heat conduction and reliability. The report says that the product has a relative density of 100% and exhibits heat conductivity of not less than 160W/mK, flexural strength of 440MPa, and fracture toughness of not less than 3.8MPa. Concerning the research and development of synergistic ceramics, studies are reported on the technologies of high-order structure control and structural element control. In relation with the technology of rendering enzyme protein thermally stable by means of molecular evolution, reports are delivered on enabling enzyme protein to withstand higher temperatures, genetic manipulation of highly thermophilic microbes, building of heat resistance with the progress of evolution, stabilization of enzymes, and the adaptation of thermophilic bacterial enzyme to normal temperature. Concerning the atom technology project, the result of the 1st phase is reported, and development in the future is predicted. Reported in relation to superconducting materials and devices is the development of a material capable of withstanding a high current density and strong magnetic field. (NEDO)

  5. NEDO industrial technology subcommittee. 18th project report meeting; NEDO sangyo gijutsu bunkakai. Dai 18 kai jigyo hokokukai

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-09-01

    In relation to NEDO's (New Energy and Industrial Technology Development Organization) research and development to put to practical use a ceramic substrate material which is sinterable at low temperature and capable of high heat radiation, a report is delivered on a low-temperature continuous baking process that realizes the mass production of aluminum nitride substrates high in heat conduction and reliability. The report says that the product has a relative density of 100% and exhibits heat conductivity of not less than 160W/mK, flexural strength of 440MPa, and fracture toughness of not less than 3.8MPa. Concerning the research and development of synergistic ceramics, studies are reported on the technologies of high-order structure control and structural element control. In relation with the technology of rendering enzyme protein thermally stable by means of molecular evolution, reports are delivered on enabling enzyme protein to withstand higher temperatures, genetic manipulation of highly thermophilic microbes, building of heat resistance with the progress of evolution, stabilization of enzymes, and the adaptation of thermophilic bacterial enzyme to normal temperature. Concerning the atom technology project, the result of the 1st phase is reported, and development in the future is predicted. Reported in relation to superconducting materials and devices is the development of a material capable of withstanding a high current density and strong magnetic field. (NEDO)

  6. Soft energy vs nuclear energy

    International Nuclear Information System (INIS)

    Ando, Yoshio

    1981-01-01

    During the early 1960s, a plentiful, inexpensive supply of petroleum enabled Japanese industry to progress rapidly; however, almost all of this petroleum was imported. Even after the first oil crisis of 1973, the recent annual energy consumption of Japan is calculated to be about 360 million tons in terms of petroleum, and actual petroleum forms 73% of total energy. It is necessary for Japan to reduce reliance on petroleum and to diversify energy resources. The use of other fossil fuels, such as coal, LNG and LPG, and hydraulic energy, is considered as an established alternative. In this presentation, the author deals with new energy, namely soft energy and nuclear energy, and discusses their characteristics and problems. The following kinds of energy are dealt with: a) Solar energy, b) Geothermal energy, c) Ocean energy (tidal, thermal, wave), d) Wind energy, e) Biomass energy, f) Hydrogen, g) Nuclear (thermal, fast, fusion). To solve the energy problem in future, assiduous efforts should be made to develop new energy systems. Among them, the most promising alternative energy is nuclear energy, and various kinds of thermal reactor systems have been developed for practical application. As a solution to the long-term future energy problem, research on and development of fast breeder reactors and fusion reactors are going on. (author)

  7. Energy Theater

    Science.gov (United States)

    Daane, Abigail R.; Wells, Lindsay; Scherr, Rachel E.

    2014-01-01

    Energy Theater is a dynamic, full-body activity that engages all students in representing the flow of energy in various phenomena, such as a light bulb burning steadily or a refrigerator cooling food. In Energy Theater, each participant acts as a unit of energy that has one form at a time. Regions on the floor correspond to objects in a physical…

  8. Energy problems

    International Nuclear Information System (INIS)

    Hoefling, O.

    1980-01-01

    The physical and technical fundamentals of energy conversion are described in popular form. There are chapters on fossil nuclear, and renewable energy sources. The final chapter attempts to give a picture of the complex interactions in the fields of energy economy and energy policy. (UA) [de

  9. Energy storage

    Energy Technology Data Exchange (ETDEWEB)

    1962-07-01

    The papers on energy storage problems, given to the United Nations Conference on New Sources of Energy, Rome, 1961, are reviewed. Many aspects of the subject are discussed: comparisons between the costs of storing energy in batteries and in fuel cells; the use, efficiency and expected improvement of fuel cells; the principles involved in the chemical conversion of solar energy to chemical energy; the use of metal hydride fuel cells; the chemical conversion and storage of concentrated solar energy for which the solar furnace is used for photochemical reactions. Finally, the general costs of storing energy in any form and delivering it are analyzed with particular reference to storage batteries and fuel cells.

  10. Advantage Energy

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2011-07-01

    Increased focus has been placed on the issues of energy access and energy poverty over the last number of years, most notably indicated by the United Nations (UN) declaring 2012 as the 'International Year of Sustainable Energy for All'. Although attention in these topics has increased, incorrect assumptions and misunderstandings still arise in both the literature and dialogues. Access to energy does not only include electricity, does not only include cook stoves, but must include access to all types of energy that form the overall energy system. This paper chooses to examine this energy system using a typology that breaks it into 3 primary energy subsystems: heat energy, electricity and transportation. Describing the global energy system using these three subsystems provides a way to articulate the differences and similarities for each system's required investments needs by the private and public sectors.

  11. Nuclear energy and energy security

    International Nuclear Information System (INIS)

    Mamasakhlisi, J.

    2010-01-01

    Do Georgia needs nuclear energy? Nuclear energy is high technology and application of such technology needs definite level of industry, science and society development. Nuclear energy is not only source of electricity production - application of nuclear energy increases year-by-year for medical, science and industrial use. As an energy source Georgia has priority to extend hydro-power capacity by reasonable use of all available water resources. In parallel regime the application of energy efficiency and energy conservation measures should be considered but currently this is not prioritized by Government. Meanwhile this should be taken into consideration that attempts to reduce energy consumption by increasing energy efficiency would simply raise demand for energy in the economy as a whole. The Nuclear energy application needs routine calculation and investigation. For this reason Government Commission is already established. But it seems in advance that regional nuclear power plant for South-Caucasus region would be much more attractive for future

  12. Nuclear energy

    International Nuclear Information System (INIS)

    Kuhn, W.

    1986-01-01

    This loose-leaf collection is made up of five didactically prepared units covering the following subjects: basic knowledge on nuclear energy, nuclear energy in relation to energy economy, site issues, environmental compatibility of nuclear energy, and nuclear energy in the focus of political and social action. To this was added a comprehensive collection of material: specific scientific background material, a multitude of tables, diagrams, charts etc. for copying, as well as 44 transparent charts, mostly in four colours. (orig./HP) [de

  13. What energies?

    International Nuclear Information System (INIS)

    Favennec, Jean-Pierre

    2009-01-01

    Energy consumption has developed significantly since the Second World War and population growth and improved living standards should see needs increasing even more. Traditional forecasts show that this energy consumption will continue to depend heavily on fossil energy. However, resources are limited and their use have a negative impact on the greenhouse effect and climate change. There is therefore a need to develop large quantities of renewable energy sources, to intensify energy saving programs and to pursue research in certain key areas

  14. Energy Leapfrogging

    OpenAIRE

    Arthur A. van Benthem

    2015-01-01

    Today's less developed countries (LDCs) have access to energy technologies that did not exist when today's richer countries were at similar stages of development. Do LDCs therefore consume less energy per capita than rich countries in the past? And is their economic growth associated with a lower growth in energy consumption? Can they "leapfrog" to a lower-carbon economy? I use data on energy consumption, prices, and gross domestic product for 76 countries to estimate the energy intensity of ...

  15. Energy efficiency through energy audit

    International Nuclear Information System (INIS)

    Esan, A. A.

    2000-08-01

    Energy is an essential factor to economic and social development and improved standards of living in developing countries. Nigeria in particular. There is a strong need for greater energy efficiency in every sector of economy in order to reduce costs. enhance competitiveness, conserve energy resources and reduce environmental impacts associated with production, distribution and use of energy. Energy auditing and monitoring has a significant role in any energy management and conservation project. Energy auditing as an important part of industrial energy management on plant level, represents a complex of activities aiming at the efficient use of energy. The activities are undertaken by a team of experts who use a set of measuring instruments to monitor and evaluate all the necessary data to elaborate a package of recommendations on improvements in the field of energy efficiency and possible product quality. The inefficient conversion and use of energy have been identified as a central problem for all developing countries, Nigeria inclusive, since they all consume significantly higher amounts of energy per unit of GDP than OECD countries. This aggravates energy-related environmental problems and is also a burden on domestic resources and foreign exchange. Energy prices have risen drastically in many developing countries, while energy intensities remain high. Price changes alone are not rapidly translating energy efficiency improvements. Identifying and removing the obstacles to greater energy efficiency should be priority for government in developing countries. This is why the Energy Commission, an apex organ of government on Energy matters in all its ramifications is out to encourage relatively low-cost energy audits for the Textile industries - such audits can identify ''good house-keeping's' measures, such as simply process improvements, that reduce energy consumption and operating costs. This will be followed by the training of plant workers/energy managers

  16. FY 1999 report on the survey of the history/inheritance of industrial technology. Survey of the inheritance/education of technology in museums of industrial technology in Japan; 1999 nendo sangyo gijutsu rekishi keisho chosa hokokusho. Kokunai sangyo gijutsu hakubutsukan ni okeru gijutsu keisho keihatsu chosa hen

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    For the purpose of clarifying the course of promotion of the original/creative future R and D and contributing to selection of technical themes and working-out of developmental methods, survey was conducted paying visits to museums of industrial technology in Japan which evaluate/preserve/exhibit/utilize memorial goods, data, information pertaining to the industrial technology in Japan. Museums for survey were the following ten: Chiba Museum of Science and Industry; Garasu no Sato (Glass Village); Maizuru World Brick Museum; Museum of Industrial Technology; Numata Memorial Hall/Mitsutoyo Museum of Dimensional Metrology; Omachi Energy Museum; Sake Museum; Saint Juan Bautista Museum; Subway Museum; Textile Museum Yukari. One of the points of this survey was to survey the actual state of the experimental type exhibition. The experimental type exhibition, which is wide in sphere, seems to be effective since visitors can operate it, simulate it, feel its size and make scientific experiments. However, the museums are not necessarily satisfied with the present situation. (NEDO)

  17. Report on the surveys in fiscal 1999 on foundations for establishing industrial technology strategies. Technological strategies by fields (Water related technology field); 1999 nendo sangyo gijutsu senryaku sakutei kiban chosa hokokusho. Bun'yabetsu gijutsu senryaku (mizu kanren gijutsu bun'ya)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    This paper describes the surveys to establish strategies in the water related technology field. The primary question relates to realizing a circulation type water utilization society. Establishment of technologies as the element technologies is demanded on treating trace amount harmful substances and pathogenically harmful micro-organisms such as environmental hormones. Technologies requiring early practical application include high-efficiency energy recovery from sludge by means of methane fermentation, accelerated oxidation and super critical sludge decomposition, and composting. Structuring a comprehensive water management information system is also important. Establishment is demanded on such technologies as high stability sensors to treat harmful chemical substances, ultra high sensitivity bio-sensors for risk control, and detection of pathogenic micro-organisms. Alga identification and quantification systems are also necessary. In developing a contaminated environmental water and waste water purification system, early practical application is desired on technologies to purify soil and large-quantity diluted environmental waters by utilizing such natural materials as soil and activated carbons, biotope and micro-organisms. Manufacture of high function water by utilizing electromagnetic waves and ultra-sonic waves, and high-efficiency low-cost desalting technologies by means of membrane separation and evaporation are also required to be developed as water resource utilizing and water making technologies. (NEDO)

  18. Technological development for super-high efficiency solar cells. Technological development for crystalline compound solar cells (high-efficiency III-V tandem solar cells); Chokokoritsu taiyo denchi no gijutsu kaihatsu. Kessho kagobutsu taiyo denchi no gijutsu kaihatsu (III-V zoku kagobutsu handotai taiyo denchi no gijutsu kaihatsu)

    Energy Technology Data Exchange (ETDEWEB)

    Tatsuta, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

    1994-12-01

    This paper reports the study results on technological development of III-V compound semiconductor solar cells in fiscal 1994. (1) On development of epitaxial growth technology of lattice mismatching systems, the optimum structure of InGaAs strain intermediate layers was studied for reducing a dislocation density by lattice mismatching of GaAs layer grown on Si substrate and difference in thermal expansion coefficient. The effect of strain layer on dislocation reduction was found only at 250dyne/cm in strain energy. Growth of GaAs layers on the Si substrate treated by hydrofluoric acid at low temperature was attempted by MBE method. As a dislocation distribution was controlled by laying different atoms at hetero-interface, the dislocation density of growing layer surfaces decreased by concentration of dislocation at hetero-interface. (2) On development of high-efficiency tandem cell structure, tunnel junction characteristics, cell formation process and optimum design method of lattice matching tandem cells were studied, while thin film cell formation was basically studied for lattice mismatching tandem cells. 45 figs., 8 tabs.

  19. Wavefield analysis in inhomogeneous media by wavelet transform; Wavelet henkan ni yoru fukinshitsu baitai no hadoba kaiseki

    Energy Technology Data Exchange (ETDEWEB)

    Matsushima, J; Rokugawa, S; Kato, Y [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Yokota, T; Miyazaki, T [Geological Survey of Japan, Tsukuba (Japan); Ichie, Y [The University of Tokyo, Tokyo (Japan)

    1996-10-01

    Data processing techniques have been investigated for clarifying structures and physical properties of geothermal reservoirs in the deep underground by seismic exploration using multiple wells. They include the initial motion time-distance tomography, amplitude tomography, diffracted wave tomography, and structure imaging using reflected wave or scattered wave. When applying these data processing methods to observed records, weak and minor signals essentially required are canceled due to averaging the analytical fields. In this study, influence of inhomogeneous media on the wavefield was evaluated. Data were analyzed considering frequency by using wavelet transform by which time-frequency can be easily analyzed. From the time-frequency analysis using wavelet transform, it was illustrated that high frequency scattered waves, generated by scatterer like cracks or by irregularity on the reflection surface, arrive behind direct P-wave and direct S-wave. 5 refs., 8 figs.

  20. Deciphering energy

    International Nuclear Information System (INIS)

    Dessus, Benjamin

    2014-01-01

    In this book, the author aims at giving some explanations about the various terms regarding energy which are present in our everyday life, in speeches, in papers and magazines, on the air, in our energy bills, for instance: energy poverty, price of a barrel of oil, resources and proved reserves, intermittency and energy storage, fossil and renewable energies, and so on. In a first part, the author addresses issues ranging from the development needs of a society to the energy assessment of a country, i.e.: nature and quantity of needs in services provided by energy, analysis of the required quantity of energy products needed to satisfy these needs, stages between primary resources and service delivery, description of the French consumption of available final energy products (per product and per economic sector). In the second part, he addresses energy supply, energy sectors and environmental issues, thus focusing on the front end of the energy system, i.e. ways of production from primary energy resources to final energy products: main physical characteristics and description of the different fissile, fossil and renewable energies, description of the main sectors of production of final energy products (fuels, electricity, heat) with a specific attention to electricity. In this part, local, regional and global environmental issues related to the exploitation of these energy sectors are discussed: sources of atmospheric pollution related to energy, relationship between energy and global warming, role of the different greenhouse gases emitted by these sectors, and quantitative analysis of these emissions. The third part addresses the economy of energy systems. The author proposes a cost assessment method which can be used for the production analysis as well as the economic analysis of a specific energy product. He also described external costs and profits, and methods to take those hidden costs and profits into account. Other economic tools are discussed and compared

  1. Energy Consumption vs. Energy Requirement

    Science.gov (United States)

    Fan, L. T.; Zhang, Tengyan; Schlup, John R.

    2006-01-01

    Energy is necessary for any phenomenon to occur or any process to proceed. Nevertheless, energy is never consumed; instead, it is conserved. What is consumed is available energy, or exergy, accompanied by an increase in entropy. Obviously, the terminology, "energy consumption" is indeed a misnomer although it is ubiquitous in the…

  2. The hydro energy; Energie hydraulique

    Energy Technology Data Exchange (ETDEWEB)

    Vachey, C.

    2000-05-01

    This paper is a first approach of the hydro energy energy. It presents the principle and the applications of this energy source. It proposes recommendations on the sizing and the cost estimation of an installation and the environmental impacts of this energy. (A.L.B.)

  3. Energy audit and energy security

    Directory of Open Access Journals (Sweden)

    Beata Agnieszka Kulessa

    2013-07-01

    Full Text Available In article, we present the issue of energy security. This article to answer the questions concerning the future of energy in Poland. These activities are directly related to energy security and the reduction of CO2 emissions. One element of this plan is the introduction in the EU energy certification of buildings. The energy certificates in Poland launched on 01.01.2009 and implements the objectives adopted by the European Union and contribute to energy security, increasing energy efficiency in construction and environmental protection.

  4. Energy accountancy

    International Nuclear Information System (INIS)

    Boer, G.A. de.

    1981-01-01

    G.A. de Boer reacts to recently published criticism of his contribution to a report entitled 'Commentaar op het boek 'Tussen Kernenergie en Kolen. Een Analyse' van ir. J.W. Storm van Leeuwen' (Commentary on the book 'Nuclear Energy versus Coal. An Analysis by ir. J.W. Storm van Leeuwen), published by the Dutch Ministry of Economic Affairs. The contribution (Appendix B) deals with energy analyses. He justifies his arguments for using energy accountancy for assessing different methods of producing electricity, and explains that it is simply an alternative to purely economic methods. The energy conversion yield (ratio of energy produced to energy required) is tabulated for different sources. De Boer emphasises that his article purposely discusses among other things, definitions, forms of energy, the limits of the systems, the conversion of money into energy and the definition of the energy yield at length, in order to prevent misunderstandings. (C.F.)

  5. Clean energy : nuclear energy world

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2007-10-15

    This book explains the nuclear engineering to kids with easy way. There are explanations of birth of nuclear energy such as discover of nuclear and application of modern technology of nuclear energy, principles and structure of nuclear power plant, fuel, nuclear waste management, use of radiation for medical treatment, food supplies, industry, utilization of neutron. It indicates the future of nuclear energy as integral nuclear energy and nuclear fusion energy.

  6. Energy sources

    International Nuclear Information System (INIS)

    Vajda, Gy.

    1998-01-01

    A comprehensive review is presented of the available sources of energy in the world is presented. About 80 percent of primary energy utilization is based on fossile fuels, and their dominant role is not expected to change in the foreseeable future. Data are given on petroleum, natural gas and coal based power production. The role and economic aspects of nuclear power are analyzed. A brief summary of renewable energy sources is presented. The future prospects of the world's energy resources are discussed, and the special position of Hungary regarding fossil, nuclear and renewable energy and the country's energy potential is evaluated. (R.P.)

  7. Renewable energy

    International Nuclear Information System (INIS)

    Berghmans, J.

    1994-01-01

    Renewable energy sources have a sma