Recent progress in thermochromics and electrochromics: A brief survey

Energy Technology Data Exchange (ETDEWEB)

Granqvist, Claes G., E-mail: claes-goran.granqvist@angstrom.uu.se

2016-09-01

Contemporary architecture is characterized by large glazings, which are able to accomplish good indoors–outdoors contact and daylighting. However, glazings, encompassing windows and glass facades, are challenging with regard to energy efficiency and often lead to excessive solar energy ingress and to large thermal losses, which must be balanced by energy-demanding cooling or heating. Cooling, especially, has grown strongly in importance during recent years. Emerging technologies utilizing thermochromics and electrochromics allow control of the inflow of visible light and solar energy and thereby produce better energy efficiency than traditional glazings employing static solutions. Thermochromic thin films, based on vanadium dioxide, let through less solar energy at high temperature than at low temperature, whereas electrochromic devices include thin films—usually based on tungsten oxide and nickel oxide—that can change their transmittance of solar energy and visible light upon the application of a voltage. It is important that electrochromics, and to some degree thermochromics, can enhance indoor comfort and lead to better living and working conditions. The present brief review covers a number of recent advances in thermochromics and electrochromics with a view to applications in energy-efficient buildings. - Highlights: • Thermochromics and electrochromics are introduced • These technologies are based on thin oxide films • Smart windows use thermochromics and electrochromics • The technologies can lead to energy efficiency in windows.

Recent progress in thermochromics and electrochromics: A brief survey

International Nuclear Information System (INIS)

Granqvist, Claes G.

2016-01-01

Contemporary architecture is characterized by large glazings, which are able to accomplish good indoors–outdoors contact and daylighting. However, glazings, encompassing windows and glass facades, are challenging with regard to energy efficiency and often lead to excessive solar energy ingress and to large thermal losses, which must be balanced by energy-demanding cooling or heating. Cooling, especially, has grown strongly in importance during recent years. Emerging technologies utilizing thermochromics and electrochromics allow control of the inflow of visible light and solar energy and thereby produce better energy efficiency than traditional glazings employing static solutions. Thermochromic thin films, based on vanadium dioxide, let through less solar energy at high temperature than at low temperature, whereas electrochromic devices include thin films—usually based on tungsten oxide and nickel oxide—that can change their transmittance of solar energy and visible light upon the application of a voltage. It is important that electrochromics, and to some degree thermochromics, can enhance indoor comfort and lead to better living and working conditions. The present brief review covers a number of recent advances in thermochromics and electrochromics with a view to applications in energy-efficient buildings. - Highlights: • Thermochromics and electrochromics are introduced • These technologies are based on thin oxide films • Smart windows use thermochromics and electrochromics • The technologies can lead to energy efficiency in windows

Electrochromic Devices Based on Porous Tungsten Oxide Thin Films

Directory of Open Access Journals (Sweden)

Y. Djaoued

2012-01-01

Full Text Available Recent developments in the synthesis of transition metal oxides in the form of porous thin films have opened up opportunities in the construction of electrochromic devices with enhanced properties. In this paper, synthesis, characterization and electrochromic applications of porous WO3 thin films with different nanocrystalline phases, such as hexagonal, monoclinic, and orthorhombic, are presented. Asymmetric electrochromic devices have been constructed based on these porous WO3 thin films. XRD measurements of the intercalation/deintercalation of Li+ into/from the WO3 layer of the device as a function of applied coloration/bleaching voltages show systematic changes in the lattice parameters associated with structural phase transitions in LixWO3. Micro-Raman studies show systematic crystalline phase changes in the spectra of WO3 layers during Li+ ion intercalation and deintercalation, which agree with the XRD data. These devices exhibit interesting optical modulation (up to ~70% due to intercalation/deintercalation of Li ions into/from the WO3 layer of the devices as a function of applied coloration/bleaching voltages. The obtained optical modulation of the electrochromic devices indicates that, they are suitable for applications in electrochromic smart windows.

High performance passive matrix electrochromic display

International Nuclear Information System (INIS)

Aliev, A.E.

2003-01-01

A matrix addressable electrochromic display (ECD) based on solid polymer electrolyte screen-printed on the surface of nano structured WO 3 +0.1TiO 2 electrodes, in which all pixels were insulted by negative photoresist material has been developed. Five types of nano structured films produced by a sol-gel method were investigated to enhance the electrochemical, optical, and mechanical properties of electrochromic tungsten oxide films. The film based on WO 3-x +0.1TiO 2-y sol-gel solution mixed with 32 mol.% oxalic acid was found to be stable and has excellent characteristics in coloring/bleaching kinetics. The ECD used nano structured electrochromic tungsten trioxide layer protected by SiO 2 -CeO 2 -Li 2 O thin film solid electrolyte, screen-printed solid polymer electrolyte mixed with white TiO 2 pigment (P25), and metallic counter electrode covered with carbon layer, has exhibited fast switching, excellent memory effect and substantially free from image diffusion and cross talk effects. (author)

Electrochromism for organic materials in polymeric all-solid-state systems

Science.gov (United States)

Hirai, Yoshihiko; Tani, Chizuka

1983-10-01

This letter reports a new electrochromic polymeric film system consisting of a polymer, an electrochromic (EC) dye which is pyrazoline or tetrathiafulvalene (TTF), and lithium perchlorate (LiClO4). The electrochromic cell structure is glass/ITO/polymeric EC film/Au film. The cell using pyrazoline as an EC dye exhibited yellow coloration at 1.0 V and the cell with TTF exhibited red coloration at 3.5 V. These cells exhibited memory.

Electrochromic Molecular Imprinting Sensor for Visual and Smartphone-Based Detections.

Science.gov (United States)

Capoferri, Denise; Álvarez-Diduk, Ruslan; Del Carlo, Michele; Compagnone, Dario; Merkoçi, Arben

2018-05-01

Electrochromic effect and molecularly imprinted technology have been used to develop a sensitive and selective electrochromic sensor. The polymeric matrices obtained using the imprinting technology are robust molecular recognition elements and have the potential to mimic natural recognition entities with very high selectivity. The electrochromic behavior of iridium oxide nanoparticles (IrOx NPs) as physicochemical transducer together with a molecularly imprinted polymer (MIP) as recognition layer resulted in a fast and efficient translation of the detection event. The sensor was fabricated using screen-printing technology with indium tin oxide as a transparent working electrode; IrOx NPs where electrodeposited onto the electrode followed by thermal polymerization of polypyrrole in the presence of the analyte (chlorpyrifos). Two different approaches were used to detect and quantify the pesticide: direct visual detection and smartphone imaging. Application of different oxidation potentials for 10 s resulted in color changes directly related to the concentration of the analyte. For smartphone imaging, at fixed potential, the concentration of the analyte was dependent on the color intensity of the electrode. The electrochromic sensor detects a highly toxic compound (chlorpyrifos) with a 100 fM and 1 mM dynamic range. So far, to the best of our knowledge, this is the first work where an electrochromic MIP sensor uses the electrochromic properties of IrOx to detect a certain analyte with high selectivity and sensitivity.

Double-Sided Electrochromic Device Based on Metal-Organic Frameworks.

Science.gov (United States)

Mjejri, Issam; Doherty, Cara M; Rubio-Martinez, Marta; Drisko, Glenna L; Rougier, Aline

2017-11-22

Devices displaying controllably tunable optical properties through an applied voltage are attractive for smart glass, mirrors, and displays. Electrochromic material development aims to decrease power consumption while increasing the variety of attainable colors, their brilliance, and their longevity. We report the first electrochromic device constructed from metal organic frameworks (MOFs). Two MOF films, HKUST-1 and ZnMOF-74, are assembled so that the oxidation of one corresponds to the reduction of the other, allowing the two sides of the device to simultaneously change color. These MOF films exhibit cycling stability unrivaled by other MOFs and a significant optical contrast in a lithium-based electrolyte. HKUST-1 reversibly changed from bright blue to light blue and ZnMOF-74 from yellow to brown. The electrochromic device associates the two MOF films via a PMMA-lithium based electrolyte membrane. The color-switching of these MOFs does not arise from an organic-linker redox reaction, signaling unexplored possibilities for electrochromic MOF-based materials.

Electrochromic properties of self-assembled nanoparticle multilayer films

International Nuclear Information System (INIS)

Xue Bo; Li Hong; Zhang Lanlan; Peng Jun

2010-01-01

Hexagonal tungsten bronze (HTB) nanocrystal and TiO 2 nanoparticles were assembled into thin films by layer-by-layer self-assembly method. HTB nanocrystals were synthesized by hydrothermal route at 155 o C. UV-Vis spectra showed that the HTB/TiO 2 films exhibit a linear increase in film thickness with assembly exposure steps. The electrochromic property of the film was carefully investigated. Cyclic voltammetry indicated that the redox peak was around -0.5 V. The electrochromic contrast, coloration efficiency, switching speed, stability and optical memory were carefully investigated. The films vary from white to blue and finally dark brown. The electrochromic contrast is 63.9% at 633 nm. The coloration efficiency of the films is relatively high. The response time is less than 3 s.

Photochemical stability of electrochromic polymers and devices

DEFF Research Database (Denmark)

Jensen, Jacob; Madsen, Morten Vesterager; Krebs, Frederik C

2013-01-01

The stability of fully printed flexible organic electrochromics based on 11 different conjugated polymers is explored from the fundamental chemical degradation level to the operational device level. The photochemical stability of the electrochromic polymers (ECPs) is studied enabling an analysis ...... based on flexible barrier substrates exhibit increased stability and are indeed viable in devices such as shading elements, light management systems, displays with low switching speed requirements and signage. © 2013 The Royal Society of Chemistry....

Characterisation and application of WO3 films for electrochromic devices

Science.gov (United States)

Stapinski, Thomas; Marszalek, Konstanty; Swatowska, Barbara; Stanco, Agnieszka

2013-07-01

Electrochromic system is the one of the most popular devices using color memory effect under the influence of an applied voltage. The electrochromic system was produced based on the thin WO3 electrochromic films. Films were prepared by RF magnetron sputtering from tungsten targets in a reactive Ar+O2 gas atmosphere of various Ar/O2 ratios. The technological gas mixture pressure was 3 Pa and process temperature 30°C. Structural and optical properties of WO3 films were investigated for as-deposited and heat treated samples at temperature range from 350°C to 450°C in air. The material revealed the dependence of properties on preparation conditions and on post-deposition heat treatment. Main parameters of thin WO3 films: thickness d, refractive index n, extinction coefficient k and energy gap Eg were determined and optimized for application in electrochromic system. The main components of the system were glass plate with transparent conducting oxides, electrolyte, and glass plate with transparent conducting oxides and WO3 layer. The optical properties of the system were investigated when a voltage was applied across it. The electrochromic cell revealed the controllable transmittance depended on the operation voltage.

Application of Nanostructures in Electrochromic Materials and Devices: Recent Progress

Directory of Open Access Journals (Sweden)

Jin Min Wang

2010-11-01

Full Text Available The recent progress in application of nanostructures in electrochromic materials and devices is reviewed. ZnO nanowire array modified by viologen and WO3, crystalline WO3 nanoparticles and nanorods, mesoporous WO3 and TiO2, poly(3,4-ethylenedioxythiophene nanotubes, Prussian blue nanoinks and nanostructures in switchable mirrors are reviewed. The electrochromic properties were significantly enhanced by applying nanostructures, resulting in faster switching responses, higher stability and higher optical contrast. A perspective on the development trends in electrochromic materials and devices is also proposed.

Preparation and Characterization of Carbon Nano tube-based Electrochromic Material

International Nuclear Information System (INIS)

Muhammad Shahazmi Mohd Zambri; Norani Muti Mohamed; Kait, C.F.

2011-01-01

Electrochromic materials that can change their optical properties reversibly for an applied potential due to electrochemical oxidation and reduction have been used in various applications of electrochromic windows or smart glass. Conducting polymer like poly aniline (PANI) is one of the most promising electrochromic materials because of its ease of synthesis and environmental stability. However, the electrochemically deposited poly aniline exhibit substantial resistivity which is attributed to the lack of conducting pathways at the nano scale associated with random deposition morphology. This paper describes the study in developing electrochromic material that will exhibit higher conductivity by using carbon nano tubes (CNTs) as the filler. Preparation of electrochromic material on ITO and FTO glass substrate was done by electrochemical process using mixture of CNTs and PANI in H 2 SO 4 at several loading of CNTs, voltage applied and duration of the process. PANI and PANI/ CNTs films produced were then characterized using SEM and Hall Effect measurement. From the study, highly conductive PANI/ CNTs film can be obtained by using optimum condition of the process parameters. PANI film deposited on FTO glass substrate was also found to be of good quality with conductivity two orders of magnitude higher than the film deposited on ITO glass substrate. (author)

Characterization of MAPLE deposited WO3 thin films for electrochromic applications

Science.gov (United States)

Boyadjiev, S. I.; Stefan, N.; Szilágyi, I. M.; Mihailescu, N.; Visan, A.; Mihailescu, I. N.; Stan, G. E.; Besleaga, C.; Iliev, M. T.; Gesheva, K. A.

2017-01-01

Tungsten trioxide (WO3) is a widely studied material for electrochromic applications. The structure, morphology and optical properties of WO3 thin films, grown by matrix assisted pulsed laser evaporation (MAPLE) from monoclinic WO3 nano-sized particles, were investigated for their possible application as electrochromic layers. A KrF* excimer (λ=248 nm, ζFWHM=25 ns) laser source was used in all experiments. The MAPLE deposited WO3 thin films were studied by atomic force microscopy (AFM), grazing incidence X-ray diffraction (GIXRD) and Fourier transform infrared spectroscopy (FTIR). Cyclic voltammetry measurements were also performed, and the coloring and bleaching were observed. The morpho-structural investigations disclosed the synthesis of single-phase monoclinic WO3 films consisting of crystalline nano-grains embedded in an amorphous matrix. All thin films showed good electrochromic properties, thus validating application of the MAPLE deposition technique for the further development of electrochromic devices.

Characterization of MAPLE deposited WO3 thin films for electrochromic applications

International Nuclear Information System (INIS)

Boyadjiev, S I; Iliev, M T; Stefan, N; Mihailescu, N; Visan, A; Mihailescu, I N; Szilágyi, I M; Stan, G E; Besleaga, C; Gesheva, K A

2017-01-01

Tungsten trioxide (WO 3 ) is a widely studied material for electrochromic applications. The structure, morphology and optical properties of WO 3 thin films, grown by matrix assisted pulsed laser evaporation (MAPLE) from monoclinic WO 3 nano-sized particles, were investigated for their possible application as electrochromic layers. A KrF* excimer (λ=248 nm, ζ FWHM =25 ns) laser source was used in all experiments. The MAPLE deposited WO 3 thin films were studied by atomic force microscopy (AFM), grazing incidence X-ray diffraction (GIXRD) and Fourier transform infrared spectroscopy (FTIR). Cyclic voltammetry measurements were also performed, and the coloring and bleaching were observed. The morpho-structural investigations disclosed the synthesis of single-phase monoclinic WO 3 films consisting of crystalline nano-grains embedded in an amorphous matrix. All thin films showed good electrochromic properties, thus validating application of the MAPLE deposition technique for the further development of electrochromic devices. (paper)

Carbazole based electrochromic polymers with benzoazole units: Effect of heteroatom variation on electrochromic performance

Directory of Open Access Journals (Sweden)

C. Doyranli

2016-09-01

Full Text Available A series of carbazole-based polymers were synthesized via Suzuki polymerization between N-(2-ethylhexylcarbazole-3,6-bis(ethyleneboronate (Cbz and dibromobenzazole unit. Three different polymers, PCBN, PCBS and PCBSe were obtained from 4,7-dibromo-2-hexyl-2H-benzotriazole (BN, 4,7-dibromo-2,1,3-benzothiadiazole- (BS and 4,7-dibromo-2,1,3-benzoselenadiazole (BSe, respectively. It is observed that, the variation of heteroatoms (N,S and Se on the benzazole unit have most important effect on electro-optic properties of the PCBX polymers. Neutral state color of the polymer films and their electrochromic performances are also influenced. Among the synthesized polymers, the PCBS bearing 2,1,3-benzothiadiazole as acceptor units has a broad absorption and 50% of ΔT in the near-IR regime at the oxidized state. This property of PCBS is a great advantage for near-IR electrochromic applications.

The optical and electrochemical properties of electrochromic films: WO3+xV2O5

Science.gov (United States)

Li, Zhuying; Liu, Hui; Liu, Ye; Yang, Shaohong; Liu, Yan; Wang, Chong

2010-05-01

Since Deb's experiment in 1973 on the electrochromic effect, transmissive electrochromic films exhibit outstanding potential as energy efficient window controls which allow dynamic control of the solar energy transmission. These films with non-volatile memory, once in the coloured state, remain in the same state even after removal of the field. The optical and electrochemical properties of electrochromic films using magnetron sputter deposition tungsten oxide thin films and vanadium oxide doped tungsten-vanadium oxide thin films on ITO coated glass were investigated. From the UV region of the transmittance spectra, the optical band gap energy from the fundamental absorption edge can be determined. And the Cyclic voltammograms of these thin films in 1 mol LiClO4 propylene carbonate electrolyte (LIPC) were measured and analysed. The anode electrochromic V2O5 doped cathode electrochromic WO3 could make films colour changing while the transmittance of films keeped invariance. These performance characteristics make tungstenvanadium oxide colour changeably thin films are suitable for electrochromic windows applications.

Electrochromic properties of nanocrystalline MoO3 thin films

International Nuclear Information System (INIS)

Hsu, C.-S.; Chan, C.-C.; Huang, H.-T.; Peng, C.-H.; Hsu, W.-C.

2008-01-01

Electrochromic MoO 3 thin films were prepared by a sol-gel spin-coating technique. The spin-coated films were initially amorphous; they were calcined, producing nanocrystalline MoO 3 thin films. The effects of annealing temperatures ranging from 100 o C to 500 o C were investigated. The electrochemical and electrochromic properties of the films were measured by cyclic voltammetry and by in-situ optical transmittance techniques in 1 M LiClO 4 /propylene carbonate electrolyte. Experimental results showed that the transmittance of MoO 3 thin films heat-treated at 350 o C varied from 80% to 35% at λ = 550 nm (ΔT = ∼ 45%) and from 86% to 21% at λ ≥ 700 nm (ΔT = ∼ 65%) after coloration. Films heat-treated at 350 deg. C exhibited the best electrochromic properties in the present study

A Paper-Based Electrochromic Array for Visualized Electrochemical Sensing

OpenAIRE

Fengling Zhang; Tianyi Cai; Liang Ma; Liyuan Zhan; Hong Liu

2017-01-01

We report a battery-powered, paper-based electrochromic array for visualized electrochemical sensing. The paper-based sensing system consists of six parallel electrochemical cells, which are powered by an aluminum-air battery. Each single electrochemical cell uses a Prussian Blue spot electrodeposited on an indium-doped tin oxide thin film as the electrochromic indicator. Each electrochemical cell is preloaded with increasing amounts of analyte. The sample activates the battery for the sensin...

Study on Electrochromic Effect of Polyaniline Film

Directory of Open Access Journals (Sweden)

Lienda Handojo

2010-10-01

Full Text Available The light transmission factor of an electrochromic film changes reversibly with the application of an electrical voltage. Thereby the transparent film becomes reversibly opaque so that it may be used to control light transmission. In this paper the results of a study on polyaniline film as an electrochromic active material is reported. Polyaniline looks yellow transparent in the reduced state and turns to green-blue at its oxidized state. The electrochromic device considered in this paper was fabricated in planar configuration of ITO glass - polyaniline film - electrolyte - ITO glass which involved 1.0M H2SO4 solution. The measurement of the current density yields voltamograms for several values of the rate of voltage change, while the optical  characteristics were measured with ultraviolet-visible spectroscopy. To inspect the light control properties, the intensity of solar radiation propagating through the device was derived. It is found that in its reduced state, the device transmits 70% of the incoming radiation, while in the oxidized state only 11% of the radiation is left. The result of recycling test indicated that film is stable over 5,000 cycles.

Effect of micro-patterned fluorine-doped tin oxide films on electrochromic properties of Prussian blue films

International Nuclear Information System (INIS)

Lee, Kyuha; Kim, A-Young; Park, Ji Hun; Jung, Hun-Gi; Choi, Wonchang; Lee, Hwa Young; Lee, Joong Kee

2014-01-01

Graphical abstract: - Highlights: • PB-based ECD employed micro-patterned FTO electrode was fabricated. • Effect of interface morphology on electrochromic characteristics was examined. • Electrochromic properties were enhanced by employing a patterned interface. - Abstract: The effect of interface morphology on electrochromic characteristics was examined for an electrochromic device (ECD). Micro-patterned fluorine-doped tin oxide (FTO) films were fabricated using a photolithography process. Prussian blue (PB) films were then deposited on the patterned FTO films. The surface areas of both PB films and FTO films were increased by patterning. ECDs were assembled using patterned PB/FTO films as the electrochromic electrode, bare FTO films as the counter electrode, and an electrolyte containing LiClO 4 salt. The increased effective surface area of the patterned PB/FTO electrode boosted the mobility of ions at the interphase between the electrolyte and PB electrode, and the electron transfer between PB films and FTO films. As a result, electrochromic properties such as transmittance and response time were significantly improved by employing the patterned FTO films as the transparent conductive oxide layer of the electrochromic electrode

Patterned polyaniline encapsulated in titania nanotubes for electrochromism.

Science.gov (United States)

Lv, Haiming; Wang, Yi; Pan, Lei; Zhang, Leipeng; Zhang, Hangchuan; Shang, Lei; Qu, Huiying; Li, Na; Zhao, Jiupeng; Li, Yao

2018-02-21

In this article, we report the preparation of a TiO 2 nanotube array (TNA) film used as a transparent electrochromic material and a TNA/polyaniline patterned hybrid electrochromic film utilized as an information display material. The TNA film was fabricated by an anodizing process, and a surface patterned TNA with extreme wettability contrast (hydrophilic/hydrophobic) on a TNA surface through self-assembly (SAM) and photocatalytic lithography is fabricated. Then the TNA/polyaniline hybrid film was prepared by electrodeposition of aniline in an aqueous solution. Finally, the electrochromic properties of the TNA film and the TNA/polyaniline hybrid film were investigated. Compared with neat TNA film and polyaniline (PANI) films, the hybrid film shows a much higher optical contrast in the near infrared range. The TNA/polyaniline hybrid film shows higher coloration efficiencies of 24.4 cm 2 C -1 at a wavelength of 700 nm and 17.1 cm 2 C -1 at a wavelength of 1050 nm compared to the TNA coloration efficiency. The color switching time (20.9 s or 22.9 s) of TNA/polyaniline is faster than TNA.

Effect of micro-patterned fluorine-doped tin oxide films on electrochromic properties of Prussian blue films

Energy Technology Data Exchange (ETDEWEB)

Lee, Kyuha [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Kim, A-Young [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Department of Material Science and Engineering, Korea University, Seoul 136-701 (Korea, Republic of); Park, Ji Hun; Jung, Hun-Gi; Choi, Wonchang; Lee, Hwa Young [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of); Lee, Joong Kee, E-mail: leejk@kist.re.kr [Center for Energy Convergence Research, Green City Technology Institute, Korea Institute of Science and Technology, Hwarangno 14-gil 5, Seongbuk-gu, Seoul 136-791 (Korea, Republic of)

2014-09-15

Graphical abstract: - Highlights: • PB-based ECD employed micro-patterned FTO electrode was fabricated. • Effect of interface morphology on electrochromic characteristics was examined. • Electrochromic properties were enhanced by employing a patterned interface. - Abstract: The effect of interface morphology on electrochromic characteristics was examined for an electrochromic device (ECD). Micro-patterned fluorine-doped tin oxide (FTO) films were fabricated using a photolithography process. Prussian blue (PB) films were then deposited on the patterned FTO films. The surface areas of both PB films and FTO films were increased by patterning. ECDs were assembled using patterned PB/FTO films as the electrochromic electrode, bare FTO films as the counter electrode, and an electrolyte containing LiClO{sub 4} salt. The increased effective surface area of the patterned PB/FTO electrode boosted the mobility of ions at the interphase between the electrolyte and PB electrode, and the electron transfer between PB films and FTO films. As a result, electrochromic properties such as transmittance and response time were significantly improved by employing the patterned FTO films as the transparent conductive oxide layer of the electrochromic electrode.

Polyaniline/Carbon nanotube Electrochromic Films: Electrochemical Polymerization and characterization

Science.gov (United States)

Li, Xiao-Xia; Zhao, Liang; Ma, De-Yue; Zeng, Yu-Run

2018-02-01

Polyaniline/Carbon nanotube (PANI/CNT) composite films doped with dodecyl-benzene sulfonic acid were synthesized by cyclic voltammetry on an ITO-coated glass substrate. FTIR, XRD and electrochemical analyzer were used to characterize the micro-morphology, chemical structure, crystallinity and electrochromic behavior of the films, respectively. The effect of CNT content on the properties of the films was investigated. Results show that the introducing CNTs make aniline polymerize easier than before. Within a range, the conductivity and crystallinity of PANI/CNT composites improves with CNT content increasing. The electrochromic device made from the PAN/CNT film with a CNT content of 2.5wt% presents a reflectance contrast of 38.8%, a mean response time of 2.3s and a coloration efficiency of 386.4cm2/C at 540nm. The PAN/CNT film shows better electrochromic behaviors due to some interaction between CNTs and the PANI backbones than PANI film.

Enhanced electrochromic coloration in Ag nanoparticle decorated WO3 thin films

International Nuclear Information System (INIS)

Kharade, Rohini R.; Mali, Sawanta S.; Patil, Satish P.; Patil, Kashinath R.; Gang, Myong G.; Patil, Pramod S.; Kim, Jin H.; Bhosale, Popatrao N.

2013-01-01

Highlights: • Electrochromic WO 3 /Ag nanocomposites prepared by hybrid physico-chemical route. • XRD and XPS results confirm formation of Ag 8 W 4 O 16 phase. • WO 3 /Ag thin films showed good optical transmittance change and coloration efficiency. • SPR enhanced coloration and bleaching mechanism is well explained for electrochromism. • Color stimuli are quantified using CIE chromaticity principles. -- Abstract: WO 3 /Ag composite thin films were prepared by microwave assisted sol–gel synthesis (MW-SGS) of WO 3 followed by vacuum evaporation of Ag nanoparticles and their enhanced electrochromic coloration was investigated. The composition and morphology of WO 3 thin films with different thickness of Ag layer obtained by vacuum evaporation were investigated. Distinct plasmon absorption bands of Ag nanoparticle thin films were obtained. The optical band gap energy of WO 3 /Ag films decreased with increasing the Ag layer thickness. The surface of these films has been examined using X-ray photoelectron spectroscopy (XPS) to gain information about the chemical states of species present at surfaces. Experimental results indicated that the conductivity of the films increased after surface modification by Ag layer. To investigate the origin of enhanced electrochromic absorption in optical properties, working electrode consisting of WO 3 /Ag thin film was used and observed the optical properties during electrochemical reaction. It was found that composite electrode shows enhancement in electrochromic properties in terms of optical modulation (ΔOD) and coloration efficiency (η)

Color combination of conductive polymers for black electrochromism.

Science.gov (United States)

Shin, Haijin; Kim, Yuna; Bhuvana, Thiruvelu; Lee, Jiyea; Yang, Xu; Park, Cheolmin; Kim, Eunkyoung

2012-01-01

Conducting polymers that absorb three primary colors, red, green, and blue (RGB), were introduced with a yellow electrochromic polymer (Y) for the preparation of black electrochromic devices. Red poly(3-hexylthiophene) (P3HT) and blue poly(3,4-ethylenedioxythiophene) (PEDOT) were coated on one side of the electrode as a cathodically coloring electrochromic (EC) layer, while green poly(aniline-N-butylsulfonate) (PANBS) and yellow EC poly{[1,3-bis(9',9'-dihexylfluoren-20-yl)azulenyl]-alt-[2",7"-(9",9"-dihexylfluorenyl]} (PDHFA) were coated on the opposite electrode to complete a complementary EC device. The yellow PDHFA layer effectively compensated for absorption below 450 nm and above the 600 nm region, which was lacking in the RGB electrode. The resultant RGBY ECD provided a black color near the CIE black with L*, a*, and b* values of 32, -1.1, and 3.7, respectively, covering a broad absorption in the visible range in the colored state. The state of the black EC device was maintained, even after the electricity was turned off for 200 h, showing stable memory effect. © 2011 American Chemical Society

An UV photochromic memory effect in proton-based WO3 electrochromic devices

International Nuclear Information System (INIS)

Zhang Yong; Lee, S.-H.; Mascarenhas, A.; Deb, S. K.

2008-01-01

We report an UV photochromic memory effect on a standard proton-based WO 3 electrochromic device. It exhibits two memory states, associated with the colored and bleached states of the device, respectively. Such an effect can be used to enhance device performance (increasing the dynamic range), re-energize commercial electrochromic devices, and develop memory devices

An UV photochromic memory effect in proton-based WO3 electrochromic devices

Science.gov (United States)

Zhang, Yong; Lee, S.-H.; Mascarenhas, A.; Deb, S. K.

2008-11-01

We report an UV photochromic memory effect on a standard proton-based WO3 electrochromic device. It exhibits two memory states, associated with the colored and bleached states of the device, respectively. Such an effect can be used to enhance device performance (increasing the dynamic range), re-energize commercial electrochromic devices, and develop memory devices.

Photoelectric conversion and electrochromic properties of lutetium tetrakis(tert-butyl)bisphthalocyaninate

International Nuclear Information System (INIS)

Hu, Andrew Teh; Hu Tenyi; Liu Lungchang

2003-01-01

Both photoelectric and electrochromic effects on lutetium tetrakis(tert-butyl)bisphthalocyaninate (Lu(TBPc) 2 ) have been carried out in this study. Lu(TBPc) 2 is known for its electrochromic performance, but its photoelectric effect has not mentioned in the literature. The electrochromic properties of Lu(TBPc) 2 have been measured by cyclic voltammetry (CV) and UV-Vis spectrometer at the same time. It takes less than 1.5 s for the color to change from red to green under 0.9 V. Its cycle life is at least over 500 times. Furthermore, we also investigate its photoelectric conversion properties. Its photoelectric cell exhibits a positive photo-electricity conversion effect with a short-circuit photocurrent (46.4 μA/cm 2 ) under illumination of white light (1.201 mW/cm 2 )

Electrochromic Behaviors of Water-Soluble Polyaniline with Covalently Bonded Acetyl Ferrocene

Science.gov (United States)

Xiong, Shanxin; Wang, Ru; Li, Shuaishuai; Wu, Bohua; Chu, Jia; Wang, Xiaoqin; Zhang, Runlan; Gong, Ming

2018-04-01

A novel ferrocene-containing hybrid electrochromic material was synthesized via copolymerization of aniline with p-phenylenediamine functionalized acetyl ferrocene in the presence of poly (styrene sulfonate) dopant in an aqueous medium, and neat polyaniline (PANI) was prepared for comparison. The polymerization characteristics and the structure of the copolymer were systematically studied by Fourier-transform infrared, meanwhile, their electrochromic properties and electrochemical behaviors were tested by UV-vis spectra, cyclic voltammetry and electrochemical impedance spectroscopy (EIS). It was found that the strong covalent bond and large conjugated system between PANI and ferrocene enhance the electron transfer rate and electron delocalization in the ferrocene-polyaniline (Fc-PANI) hybrid. In particular, the electrochromic device with Fc-PANI as the active layer shows significant enhancement in optical contrast over the PANI-based device.

Tungsten oxide nanowires grown on graphene oxide sheets as high-performance electrochromic material

International Nuclear Information System (INIS)

Chang, Xueting; Sun, Shibin; Dong, Lihua; Hu, Xiong; Yin, Yansheng

2014-01-01

Graphical abstract: Electrochromic mechanism of tungsten oxide nanowires-reduced graphene oxide composite. - Highlights: • A novel inorganic-nano-carbon hybrid composite was prepared. • The hybrid composite has sandwich-like structure. • The hybrid composite exhibited high-quality electrohcromic performance. - Abstract: In this work, we report the synthesis of a novel hybrid electrochromic composite through nucleation and growth of ultrathin tungsten oxide nanowires on graphene oxide sheets using a facile solvothermal route. The competition between the growth of tungsten oxide nanowires and the reduction of graphene oxide sheets leads to the formation of sandwich-structured tungsten oxide-reduced graphene oxide composite. Due to the strongly coupled effect between the ultrathin tungsten oxide nanowires and the reduced graphene oxide nanosheets, the novel electrochromic composite exhibited high-quality electrochromic performance with fast color-switching speed, good cyclic stability, and high coloration efficiency. The present tungsten oxide-reduced graphene oxide composite represents a new approach to prepare other inorganic-reduced graphene oxide hybrid materials for electrochemical applications

Electrochromic fiber-shaped supercapacitors.

Science.gov (United States)

Chen, Xuli; Lin, Huijuan; Deng, Jue; Zhang, Ye; Sun, Xuemei; Chen, Peining; Fang, Xin; Zhang, Zhitao; Guan, Guozhen; Peng, Huisheng

2014-12-23

An electrochromic fiber-shaped super-capacitor is developed by winding aligned carbon nanotube/polyaniline composite sheets on an elastic fiber. The fiber-shaped supercapacitors demonstrate rapid and reversible chromatic transitions under different working states, which can be directly observed by the naked eye. They are also stretchable and flexible, and are woven into textiles to display designed signals in addition to storing energy. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Elucidation of the electrochromic mechanism of nanostructured iron oxides films

Energy Technology Data Exchange (ETDEWEB)

Garcia-Lobato, M.A.; Martinez, Arturo I.; Castro-Roman, M. [Center for Research and Advanced Studies of the National Polytechnic Institute, Cinvestav Campus Saltillo, Carr. Saltillo-Monterrey Km. 13, Ramos Arizpe, Coah. 25900 (Mexico); Perry, Dale L. [Mail Stop 70A1150, Lawrence Berkeley National Laboratory, University of California, Berkeley, CA 94720 (United States); Zarate, R.A. [Departamento de Fisica, Facultad de Ciencias, Universidad Catolica del Norte, Casilla 1280, Antofagasta (Chile); Escobar-Alarcon, L. (Departamento de Fisica, Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, 11801 Mexico)

2011-02-15

Nanostructured hematite thin films were electrochemically cycled in an aqueous solution of LiOH. Through optical, structural, morphological, and magnetic measurements, the coloration mechanism of electrochromic iron oxide thin films was elucidated. The conditions for double or single electrochromic behavior are given in this work. During the electrochemical cycling, it was found that topotactic transformations of hexagonal crystal structures are favored; i.e. {alpha}-Fe{sub 2}O{sub 3} to Fe(OH){sub 2} and subsequently to {delta}-FeOOH. These topotactic redox reactions are responsible for color changes of iron oxide films. (author)

Electrochromic device containing metal oxide nanoparticles and ultraviolet blocking material

Science.gov (United States)

Garcia, Guillermo; Koo, Bonil; Gregoratto, Ivano; Basu, Sourav; Rosen, Evelyn; Holt, Jason; Thomsen, Scott

2017-10-17

An electrochromic device includes a nanostructured transition metal oxide bronze layer that includes one or more transition metal oxide and one or more dopant. The electrochromic device also includes nanoparticles containing one or more transparent conducting oxide (TCO), a solid state electrolyte, a counter electrode, and at least one protective layer to prevent degradation of the one or more nanostructured transition metal oxide bronze. The nanostructured transition metal oxide bronze selectively modulates transmittance of near-infrared (NIR) and visible radiation as a function of an applied voltage to the device.

Electrochromic Asymmetric Supercapacitor Windows Enable Direct Determination of Energy Status by the Naked Eye.

Science.gov (United States)

Zhong, Ying; Chai, Zhisheng; Liang, Zhimin; Sun, Peng; Xie, Weiguang; Zhao, Chuanxi; Mai, Wenjie

2017-10-04

Because of the popularity of smart electronics, multifunctional energy storage devices, especially electrochromic supercapacitors (SCs), have attracted tremendous research interest. Herein, a solid-state electrochromic asymmetric SC (ASC) window is designed and fabricated by introducing WO 3 and polyaniline as the negative and positive electrodes, respectively. The two complementary materials contribute to the outstanding electrochemical and electrochromic performances of the fabricated device. With an operating voltage window of 1.4 V and an areal capacitance of 28.3 mF cm -2 , the electrochromic devices show a high energy density of 7.7 × 10 -3 mW h cm -2 . Meanwhile, they exhibit an obvious and reversible color transition between light green (uncharged state) and dark blue (charged state), with an optical transmittance change between 55 and 12% at a wavelength of 633 nm. Hence, the energy storage level of the ASC is directly related to its color and can be determined by the naked eye, which means it can be incorporated with other energy cells to visual display their energy status. Particularly, a self-powered and color-indicated system is achieved by combining the smart windows with commercial solar cell panels. We believe that the novel electrochromic ASC windows will have great potential application for both smart electronics and smart buildings.

Electrochromic Ni–Fe oxide thin films synthesized by an atmospheric pressure plasma jet for flexible electrochromic application

Energy Technology Data Exchange (ETDEWEB)

Lin, Yun-Sen, E-mail: yslin@fcu.edu.tw; Chuang, Pei-Ying; Shie, Ping-Shiun

2014-11-03

Flexible-electrochromic organo-nickel-iron oxide (NiFe{sub x}O{sub y}C{sub z}) films deposited onto flexible polyethylene terephthalate (PET)/indium tin oxide (ITO) substrates using atmospheric-pressure plasma-enhanced chemical vapor deposition with an atmospheric pressure plasma jet under various flow rates of oxygen gases are investigated. Precursors [nickelocence, Ni(C{sub 5}H{sub 5}){sub 2}] and [ferrocence, Fe(C{sub 5}H{sub 5}){sub 2}] vapors are carried by argon gas, mixed by oxygen gas and injected into air plasma torch for a rapid synthesis of NiFe{sub x}O{sub y}C{sub z} films by a short duration of the substrate, 32 s, in the plasmas. Uniform light modulation on PET/ITO/NiFe{sub x}O{sub y}C{sub z} is produced while the moving PET/ITO substrate is exposed to plasma torch at room temperature (∼ 23 °C) and atmospheric pressure. Light modulation with up to a 43.2% transmittance variation at a wavelength of 708 nm even after 200 cycles of Li{sup +} intercalation and de-intercalation in a 1 M LiClO{sub 4}-propylene carbonate electrolyte is accomplished. - Highlights: • Rapid deposition of electrochromic organo-nickel–iron oxide (NiFe{sub x}O{sub y}C{sub z}) films • Enhanced electrochromic performance of NiFe{sub x}O{sub y}C{sub z} films by oxygen gas addition • Uniform light modulation on NiFe{sub x}O{sub y}C{sub z} films produced by air plasma jet • Porous surfaces allow reversible Li{sup +} intercalation and deintercalation.

Paper-based electrochemical sensing platform with integral battery and electrochromic read-out.

Science.gov (United States)

Liu, Hong; Crooks, Richard M

2012-03-06

We report a battery-powered, microelectrochemical sensing platform that reports its output using an electrochromic display. The platform is fabricated based on paper fluidics and uses a Prussian blue spot electrodeposited on an indium-doped tin oxide thin film as the electrochromic indicator. The integrated metal/air battery powers both the electrochemical sensor and the electrochromic read-out, which are in electrical contact via a paper reservoir. The sample activates the battery and the presence of analyte in the sample initiates the color change of the Prussian blue spot. The entire system is assembled on the lab bench, without the need for cleanroom facilities. The applicability of the device to point-of-care sensing is demonstrated by qualitative detection of 0.1 mM glucose and H(2)O(2) in artificial urine samples.

Electrochromic Characteristics of Nitrogen-Doped Graphene/TiO2 Nanocomposite Electrodes

International Nuclear Information System (INIS)

Yang, Chien-Hsin; Chen, Shih-Ming; Wang, Tzong-Liu; Shieh, Yeong-Tarng

2014-01-01

Nitrogen-doped graphene (NDG)/titanium dioxide (TiO 2 ) nanoparticles were coated on indium-tin oxide (ITO) glass substrates to fabricate NDG-TiO 2 nanocomposite electrodes. 3-methylthiophene (3MT) was electrochemically deposited on the NDG-TiO 2 films to form poly(3-methylthiophene) (P3MT/NDG/TiO 2 ) composite electrochromic electrodes. The introduction of NDG and TiO 2 mesoporous films significantly increased the initial maximum optical contrast (ΔT%) to 70% as compared 41% of pure ITO electrodes, whereas the P3MT/NDG/TiO 2 composite electrodes enhanced the adhesion of P3MT polymers to the NDG/TiO 2 /ITO substrate, thereby increasing the long-term stability of the corresponding electrochromic devices. Experimental results reveal that P3MT/NDG/TiO 2 composite electrodes retained up to 90% of ΔT%, relative to 70% remaining ΔT% of pure ITO electrodes. This illustrates the enhanced long-term stability achieved through the introduction of a NDG-TiO 2 nanocomposite films in electrochromic devices. These devices demonstrated excellent response time characteristics and ΔT% value of 6 s and ca. of 70%, respectively. This work has shown that conductive polymer/NDG/TiO 2 composite electrodes are well suited to electrochromic devices for the promotion of performance and stability

Solid-State Electrochromic Device Consisting of Amorphous WO3 and Various Thin Oxide Layers

Science.gov (United States)

Shizukuishi, Makoto; Shimizu, Isamu; Inoue, Eiichi

1980-11-01

A mixed oxide containing Cr2O3 was introduced into an amorphous WO3 solid-state electrochromic device (ECD) in order to improve its colour memory effect. The electrochromic characteristics were greatly affected by the chemical constituents of a dielectric layer on the a-WO3 layer. Particularly, long memory effect and low power dissipation were attained in a solid-state ECD consisting of a-WO3 and Cr2O3\\cdotV2O5(50 wt.%). Some electrochromic characteristics of the a-WO3/Cr2O3\\cdotV2O5 ECD and the role of V2O5 were investigated.

Colorless triphenylamine-based aliphatic thermoset epoxy for multicolored and near-infrared electrochromic applications.

Science.gov (United States)

Chuang, Ya-Wen; Yen, Hung-Ju; Wu, Jia-Hao; Liou, Guey-Sheng

2014-03-12

In this study, two novel colorless thermoset epoxy resins with anodically electrochromism were prepared from the thermal curing of two triphenylamine-based diamine monomers, 4,4'-diamino-4″-methoxytriphenylamine (1) and N,N'-bis(4-aminophenyl)-N,N'-di(4-methoxylphenyl)-1,4-phenylenediamine (2) with aliphatic epoxy triglycidyl isocyanurate, respectively. The resulting thermoset epoxy resins showed excellent softening temperature (Ts, 270 and 280 °C) due to the rigid structure and highly crosslinking density. In addition, novel colorless epoxy resin films revealed good reversible electrochemical oxidation and interesting multi-electrochromic behavior with high contrast ratio both in visible and near-infrared regions. The aliphatic thermoset epoxy resins also exhibited high transparency in visible region as colorless and great potential for practical electrochromic applications.

Lighting energy savings potential of split-pane electrochromic windows controlled for daylighting with visual comfort

Energy Technology Data Exchange (ETDEWEB)

Software, Anyhere; Fernandes, Luis; Lee, Eleanor; Ward, Greg

2013-03-15

A simulation study was conducted to evaluate lighting energy savings of split-pane electrochromic (EC) windows controlled to satisfy key visual comfort parameters. Using the Radiance lighting simulation software, interior illuminance and luminance levels were computed for a south-facing private office illuminated by a window split into two independently-controlled EC panes. The transmittance of these was optimized hourly for a workplane illuminance target while meeting visual comfort constraints, using a least-squares algorithm with linear inequality constraints. Blinds were successively deployed until visual comfort criteria were satisfied. The energy performance of electrochromics proved to be highly dependent on how blinds were controlled. With hourly blind position adjustments, electrochromics showed significantly higher (62percent and 53percent, respectively without and with overhang) lighting energy consumption than clear glass. With a control algorithm designed to better approximate realistic manual control by an occupant, electrochromics achieved significant savings (48percent and 37percent, respectively without and with overhang). In all cases, energy consumption decreased when the workplace illuminance target was increased. In addition, the fraction of time during which the occupant had an unobstructed view of the outside was significantly greater with electrochromics: 10 months out of the year versus a handful of days for the reference case.

A novel donor-acceptor polymeric electrochromic material containing carbazole and 1,8-naphtalimide as subunit

Energy Technology Data Exchange (ETDEWEB)

Koyuncu, Fatma Baycan, E-mail: fatmabaycan@hotmail.co [Department of Chemistry, Faculty of Sciences and Arts, Canakkale Onsekiz Mart University, 17020 Canakkale (Turkey); Koyuncu, Sermet [Can Vocational School, Canakkale Onsekiz Mart University, 17400 Canakkale (Turkey); Ozdemir, Eyup, E-mail: eozdemir@comu.edu.t [Department of Chemistry, Faculty of Sciences and Arts, Canakkale Onsekiz Mart University, 17020 Canakkale (Turkey)

2010-07-01

We report here the synthesis of a novel polymeric electrochromic material containing carbazole (Cbz)-donor and 1,8-napthalimide-acceptor as subunit. The band gap E{sub g} was measured using UV-vis spectroscopy and compared with that obtained by cyclic voltammetry (CV). Due to intramolecular electron transfer from Cbz-donor to 1,8-napthalimide-acceptor, the fluorescence quenching was observed. When the spectro-electrochemical and electrochromic properties of polymer film were investigated, various tones of green color were obtained on the polymeric film. In the positive regime, the polymer film obtained thereby is dark green resulting from the association of carbazolylium cation radicals at oxidized state and then it can be bleached by electrochemical reduction. Besides, in the negative regime, yellowish green color of film converted to blue attributed to reduction of the 1,8-napthalimide moiety. Finally, the polymeric electrochromic exhibits multi-electrochromic behavior, high redox stability, high coloration efficiency and reasonable response time.

A novel donor-acceptor polymeric electrochromic material containing carbazole and 1,8-naphtalimide as subunit

International Nuclear Information System (INIS)

Koyuncu, Fatma Baycan; Koyuncu, Sermet; Ozdemir, Eyup

2010-01-01

We report here the synthesis of a novel polymeric electrochromic material containing carbazole (Cbz)-donor and 1,8-napthalimide-acceptor as subunit. The band gap E g was measured using UV-vis spectroscopy and compared with that obtained by cyclic voltammetry (CV). Due to intramolecular electron transfer from Cbz-donor to 1,8-napthalimide-acceptor, the fluorescence quenching was observed. When the spectro-electrochemical and electrochromic properties of polymer film were investigated, various tones of green color were obtained on the polymeric film. In the positive regime, the polymer film obtained thereby is dark green resulting from the association of carbazolylium cation radicals at oxidized state and then it can be bleached by electrochemical reduction. Besides, in the negative regime, yellowish green color of film converted to blue attributed to reduction of the 1,8-napthalimide moiety. Finally, the polymeric electrochromic exhibits multi-electrochromic behavior, high redox stability, high coloration efficiency and reasonable response time.

Electrochromism and local order in amorphous WO/sub 3/

Energy Technology Data Exchange (ETDEWEB)

Zeller, H R; Beyeler, H U

1977-06-01

WO/sub 3/ films prepared under different conditions (evaporation, reactive sputtering and spraying of aqueous solutions of metatungstic acid) differ by orders of magnitude in their electrochromic sensitivity. Diffuse X-ray studies show the evaporated and sputtered films to be amorphous and to consists of a disordered network of corner sharing WO/sub 6/ octahedra. Sprayed films have different degrees of crystallinity depending on spraying conditions. From differential scanning calorimetry we conclude that the crystal water present in most films strongly affects the local order of the corner sharing octahedra. We find that crystal water not only provides a high ionic conductivity which is conditional for a fast electrochromic reaction but also stabilises electrocatalytically active surface sites for fast hydrogen or Li exchange with the adjacent electrolyte.

Effect of modified ITO substrate on electrochromic properties of polyaniline films

Energy Technology Data Exchange (ETDEWEB)

Leon-Silva, U.; Nicho, M.E.; Cruz-Silva, Rodolfo [Centro de Investigacion en Ingenieria y Ciencias Aplicadas, UAEMor, Av. Universidad 1001, Col. Chamilpa, 62209, Cuernavaca, Morelos (Mexico); Hu, Hailin [Departamento de Materiales Solares, Centro de Investigacion en Energia, UNAM, Av. Xochicalco S/N, Temixco, 62580, Morelos (Mexico)

2007-09-22

In this work, we report the morphological and electrochromic properties of electrochemically synthesized polyaniline (PANI) thin films on bare and modified indium-tin oxide (ITO) glass substrates. In the last case, the surface of ITO glass was covered by a self-assembled monolayer of N-phenyl-{gamma}-aminopropyl-trimethoxysilane (PAPTS). Atomic force microscopy images and perfilometry show that smoother and thinner PANI films were grown on PAPTS-modified ITO substrates. PANI-based electrochromic devices (ECDs) were assembled by using a viscous polymeric electrolyte (PE) of LiClO{sub 4} and polymethyl methacrylate (PMMA) co-dissolved in a mixture of propylene and ethylene carbonate. The architectural design of the devices was glass/ITO/PANI/PE/ITO/glass. A dual ECD was also prepared by collocating a poly(3-methylthiophene) (P3MT) thin film as a complementary electrochromic element. The effect of the PAPTS-modified ITO substrate is reflected in a higher optical transmittance at bleach state and a little less color change at 550 nm of PANI-based ECDs. (author)

Dip-Coating Process Engineering and Performance Optimization for Three-State Electrochromic Devices

Science.gov (United States)

Wu, Lu; Yang, Dejiang; Fei, Lixun; Huang, Yue; Wu, Fang; Sun, Yiling; Shi, Jiayuan; Xiang, Yong

2017-06-01

Titanium dioxide (TiO2) nanoparticles were modified onto fluorine-doped tin oxide (FTO) via dip-coating technique with different nanoparticle sizes, lifting speeds, precursor concentrations, and dipping numbers. Electrodeposition-based electrochromic device with reversible three-state optical transformation (transparent, mirror, and black) was fabricated subsequently by sandwiching a suitable amount of gel electrolyte between modified FTO electrode and flat FTO electrode. Correlation between dip-coating process engineering, morphological features of TiO2 thin films, i.e., thickness and roughness, as well as performance of electrochromic devices, i.e., optical contrast, switching time, and cycling stability, were investigated. The modified device exhibits high optical contrast of 57%, the short coloration/bleaching switching time of 6 and 20 s, and excellent cycling stability after 1500 cycles of only 27% decrement rate by adjusting dip-coating processes engineering. The results in this study will provide valuable guidance for rational design of the electrochromic device with satisfactory performance.

Citric acid induced W18O49 electrochromic films with enhanced optical modulation

Science.gov (United States)

Xie, Junliang; Song, Bin; Zhao, Gaoling; Han, Gaorong

2018-06-01

Electrochromic materials exhibit promising applications in energy-saving fields for their ability to control heat from outdoors. Nanostructured W18O49 has drawn attention for its one-dimensional structure to transfer charge efficiently as a remarkable electrochromic material. W18O49 bi-layer films were fabricated through a facile one-step solvothermal process with citric acid as a chelating agent. The addition of citric acid improved the deposition on the substance, and a nanostructured film with a denser layer at the bottom and a tussock-like upper layer was obtained. The bi-layer film exhibited an enhanced optical modulation of 68.7%, a coloration efficiency of 82.1 cm2/C with stability over 400 cycles, and fast response times (1.4 s and 2.3 s for bleaching and coloring), with expectation to be applied in the electrochromic field.

Large-Scale Multifunctional Electrochromic-Energy Storage Device Based on Tungsten Trioxide Monohydrate Nanosheets and Prussian White.

Science.gov (United States)

Bi, Zhijie; Li, Xiaomin; Chen, Yongbo; He, Xiaoli; Xu, Xiaoke; Gao, Xiangdong

2017-09-06

A high-performance electrochromic-energy storage device (EESD) is developed, which successfully realizes the multifunctional combination of electrochromism and energy storage by constructing tungsten trioxide monohydrate (WO 3 ·H 2 O) nanosheets and Prussian white (PW) film as asymmetric electrodes. The EESD presents excellent electrochromic properties of broad optical modulation (61.7%), ultrafast response speed (1.84/1.95 s), and great coloration efficiency (139.4 cm 2 C -1 ). In particular, remarkable cyclic stability (sustaining 82.5% of its initial optical modulation after 2500 cycles as an electrochromic device, almost fully maintaining its capacitance after 1000 cycles as an energy storage device) is achieved. The EESD is also able to visually detect the energy storage level via reversible and fast color changes. Moreover, the EESD can be combined with commercial solar cells to constitute an intelligent operating system in the architectures, which would realize the adjustment of indoor sunlight and the improvement of physical comfort totally by the rational utilization of solar energy without additional electricity. Besides, a scaled-up EESD (10 × 11 cm 2 ) is further fabricated as a prototype. Such promising EESD shows huge potential in practically serving as electrochromic smart windows and energy storage devices.

Isomer effect on the near-infrared electrochromism of anthraquinone imides

International Nuclear Information System (INIS)

Yao, Bin; Chen, Fengkun; Jiang, Hong; Zhang, Jie; Wan, Xinhua

2015-01-01

Graphical abstract: Display Omitted - Highlights: • Two pairs of unsubstituted isomers (Ia and Ib) and nitro-substituted isomers (IIa and IIb) of anthraquinone imides (AQIs), which are a unique type of cathodically-colouring NIR electrochromic materials bearing both quinone and imide moieties, were synthesized. • Isomer effect on the NIR electrochromism of n-type optoelectric materials was first approached. • A meaningful reference to design cathodically active NIR EC materials, in which the molecular planarity and the orientation of polar groups are two key elements must to be carefully considered, is provided. - Abstract: To deeply explore the interplay between molecular structure and near-infrared electrochromism of anthraquinone imides, two pairs of unsubstituted isomers (Ia and Ib) and nitro-substituted isomers (IIa and IIb) of anthraquinone imides were synthesized, in which the molecules Ia and IIa took more linear shapes than Ib and IIb. Cyclic voltammetry and spectroelectrochemistry were combined to investigate their electrochemical properties. Cyclic voltammetry showed that Ib and IIb revealed decreased first reduction potentials and low cyclic stability compared to their isomers, indicating that the isomerization weakened the stabilization effect. Upon one-electron reduction, both the absorption wavelengths and absorption intensities of radical anions were greatly dependent on the structures of isomers. The radical anions of Ia, IIa, and IIb illustrated NIR absorptions peaked at 820, 1260, and 1380 nm, respectively, but that of Ib exhibited only weak absorption in the visible region centered at 660 nm. Gaussian calculations suggested that the electrons were delocalized over the whole molecular skeletons of Ia and IIa radical anions, but the effective conjugation length was interrupted on the imide section in both Ib and IIb. The isomer effects on the effective conjugation length and electron density distribution were considered to rationalize the

A Paper-Based Electrochromic Array for Visualized Electrochemical Sensing.

Science.gov (United States)

Zhang, Fengling; Cai, Tianyi; Ma, Liang; Zhan, Liyuan; Liu, Hong

2017-01-31

We report a battery-powered, paper-based electrochromic array for visualized electrochemical sensing. The paper-based sensing system consists of six parallel electrochemical cells, which are powered by an aluminum-air battery. Each single electrochemical cell uses a Prussian Blue spot electrodeposited on an indium-doped tin oxide thin film as the electrochromic indicator. Each electrochemical cell is preloaded with increasing amounts of analyte. The sample activates the battery for the sensing. Both the preloaded analyte and the analyte in the sample initiate the color change of Prussian Blue to Prussian White. With a reaction time of 60 s, the number of electrochemical cells with complete color changes is correlated to the concentration of analyte in the sample. As a proof-of-concept analyte, lactic acid was detected semi-quantitatively using the naked eye.

Gel electrolytes with ionic liquid plasticiser for electrochromic devices

International Nuclear Information System (INIS)

Desai, S.; Shepherd, R.L.; Innis, P.C.; Murphy, P.; Hall, C.; Fabretto, R.; Wallace, G.G.

2011-01-01

The comparative performance of conducting polymer electrochromic devices (ECDs) utilising gel polymer electrolytes (GPEs) plasticised with ethylene carbonate/propylene carbonate or (N-butyl-3-methylpyridinium trifluoromethanesulphonylimide (P 14 TFSI) has been made. Lithium perchlorate and lithium trifluoromethanesulphonylimide salts were used in the GPEs to provide enhanced ionic conductivity and inhibit phase separation of the polyethyleneoxide (PEO) and plasticiser. ECDs were assembled from cathodically colouring, polyethylenedioxythiophene (PEDOT), and anodically colouring, polypyrrole (PPy), conducting polymer electrochromes deposited by vapour deposition. The photopic contrast switching over the visible light spectrum, switching speeds and device stability of the ECDs were obtained. These studies demonstrate that the ionic liquid (IL) plasticised GPEs are a suitable replacement for pure IL based devices and volatile organic solvent plasticisers based upon ethylene carbonate/propylene carbonate mixtures.

Gel electrolytes with ionic liquid plasticiser for electrochromic devices

Energy Technology Data Exchange (ETDEWEB)

Desai, S.; Shepherd, R.L.; Innis, P.C. [ARC Centre of Excellence for Electromaterials Science, Intelligent Polymer Research Institute, University of Wollongong, Northfields Avenue, Wollongong, NSW 2522 (Australia); Murphy, P. [Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Mawson Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Hall, C.; Fabretto, R. [Ian Wark Research Institute, University of South Australia, Mawson Lakes, SA 5095 (Australia); Wallace, G.G., E-mail: gwallace@uow.edu.a [ARC Centre of Excellence for Electromaterials Science, Intelligent Polymer Research Institute, University of Wollongong, Northfields Avenue, Wollongong, NSW 2522 (Australia)

2011-04-15

The comparative performance of conducting polymer electrochromic devices (ECDs) utilising gel polymer electrolytes (GPEs) plasticised with ethylene carbonate/propylene carbonate or (N-butyl-3-methylpyridinium trifluoromethanesulphonylimide (P{sub 14}TFSI) has been made. Lithium perchlorate and lithium trifluoromethanesulphonylimide salts were used in the GPEs to provide enhanced ionic conductivity and inhibit phase separation of the polyethyleneoxide (PEO) and plasticiser. ECDs were assembled from cathodically colouring, polyethylenedioxythiophene (PEDOT), and anodically colouring, polypyrrole (PPy), conducting polymer electrochromes deposited by vapour deposition. The photopic contrast switching over the visible light spectrum, switching speeds and device stability of the ECDs were obtained. These studies demonstrate that the ionic liquid (IL) plasticised GPEs are a suitable replacement for pure IL based devices and volatile organic solvent plasticisers based upon ethylene carbonate/propylene carbonate mixtures.

Eliminating degradation and uncovering ion-trapping dynamics in electrochromic WO3 thin films

Science.gov (United States)

Wen, Rui-Tao; Granqvist, Claes G.; Niklasson, Gunnar A.

2015-01-01

Amorphous WO3 thin films are of keen interest as cathodic electrodes in transmittance-modulating electrochromic devices. However, these films suffer from ion-trapping-induced degradation of optical modulation and reversibility upon extended Li+-ion exchange. Here, we demonstrate that ion-trapping-induced degradation, which is commonly believed to be irreversible, can be successfully eliminated by constant-current-driven de-trapping, i.e., WO3 films can be rejuvenated and regain their initial highly reversible electrochromic performance. Pronounced ion-trapping occurs when x exceeds ~0.65 in LixWO3 during ion insertion. We find two main kinds of Li+-ion trapping sites (intermediate and deep) in WO3, where the intermediate ones are most prevalent. Li+-ions can be completely removed from intermediate traps but are irreversibly bound in deep traps. Our results provide a general framework for developing and designing superior electrochromic materials and devices. PMID:26259104

Donor-π-bridge-acceptor type polymeric materials with pendant electron-withdrawing groups for electrochromic applications

International Nuclear Information System (INIS)

Du, Qing; Wei, Youxiu; Zheng, Jianming; Xu, Chunye

2014-01-01

Highlights: • Donor-π-bridge-acceptor copolymers with different electrophilic groups were synthesized. • Electrochromic devices composed of PBDTTPAs layers, as the working electrode, and vanadium pentoxide, as the counter electrode, were fabricated and evaluated. • The PBDTTPA-CHO film and device show multicolor electrochromic behavior which exhibited vivid yellow, green, and gray with better electrochromic performance than PBDTTPA-COOH. - Abstract: A novel donor-π-bridge-acceptor copolymer, PBDTTPA-CHO, containing 4-(Bis(4-bromophenyl)-amino)benzaldehyde (TPA-CHO) and 4,8-bis-(2-ethyl- hexyloxy)-oxybenzo-[1,2-b:3,4-b’]dithiophene (BDT), was successfully synthesized using Stille coupling polymerization, and the pendant aldehyde group was modified with cyanoacetic acid to synthesize another polymer, PBDTTPA-COOH. Each of these new polymers are soluble in organic solvents and can be cast onto rigid or flexible substrates. The polymers with different electrophilic groups exhibit different electrochromic behaviors, including different colors, driving voltages and transmittances. The polymer film of PBDTTPA-CHO manifests reversible electrochemical oxidation and reduction accompanied by multicolor changes from its yellow neutral state to a highly absorbent green semi-oxidized state and a gray fully oxidized state, its transmittance change at 601 nm is 43%. PBDTTPA-COOH switches between orange and light green. We fabricated and evaluated electrochromic devices using a PBDTTPA layer as the working electrode and vanadium pentoxide as the counter electrode. With the contribution of counter electrodes, devices of both polymers show similar color changes but higher transmittance than their films

Transmissive-to-black fast electrochromic switching from a long conjugated pendant group and a highly dispersed polymer/SWNT

KAUST Repository

Zhang, Qiang

2018-01-03

In this study, a novel conjugated polymer, denoted as ECPblack, is synthesized. ECPblack demonstrated a unique electrochromic behavior with an ultrahigh contrast ratio (over 80%) in most of the visible regions, boasting an ultrahigh integrated contrast ratio of 71.8% between 380 nm and 880 nm. The long conjugated pendant group (pyrene) in ECPblack enhances the absorption in the blue region in its second oxidized state and results in transmissive-to-black electrochromic switching between the neutral state and the oxidized state. The transmissive-to-black electrochromic switching polymer with an ultrahigh contrast ratio could be especially attractive for applications in electronic displays. In addition, when polytriarylamine/nanotube (SWNT/P2) dispersion is doped in ECPblack, the response time of its electrochemical and electrochromic behaviors is further reduced. The electrochromic switching and bleaching time of SWNT/P2/ECPblack decreased by 73% and 80%, respectively. The improvement is caused by the phase separation of the rigid SWNT and the flexible polymer, which generates a rough surface morphology and provides more pathways for faster diffusion of counterions (ClO4-). The polymer/SWNT doping technique provides a simple way to accelerate ion diffusion in anodically coloring materials.

Transmissive-to-black fast electrochromic switching from a long conjugated pendant group and a highly dispersed polymer/SWNT

KAUST Repository

Zhang, Qiang; Tsai, Chou-Yi; Abidin, Taufik; Jiang, Jyh-Chiang; Shie, Wan-Ru; Li, Lain-Jong; Liaw, Der-Jang

2018-01-01

In this study, a novel conjugated polymer, denoted as ECPblack, is synthesized. ECPblack demonstrated a unique electrochromic behavior with an ultrahigh contrast ratio (over 80%) in most of the visible regions, boasting an ultrahigh integrated contrast ratio of 71.8% between 380 nm and 880 nm. The long conjugated pendant group (pyrene) in ECPblack enhances the absorption in the blue region in its second oxidized state and results in transmissive-to-black electrochromic switching between the neutral state and the oxidized state. The transmissive-to-black electrochromic switching polymer with an ultrahigh contrast ratio could be especially attractive for applications in electronic displays. In addition, when polytriarylamine/nanotube (SWNT/P2) dispersion is doped in ECPblack, the response time of its electrochemical and electrochromic behaviors is further reduced. The electrochromic switching and bleaching time of SWNT/P2/ECPblack decreased by 73% and 80%, respectively. The improvement is caused by the phase separation of the rigid SWNT and the flexible polymer, which generates a rough surface morphology and provides more pathways for faster diffusion of counterions (ClO4-). The polymer/SWNT doping technique provides a simple way to accelerate ion diffusion in anodically coloring materials.

A Paper-Based Electrochromic Array for Visualized Electrochemical Sensing

Directory of Open Access Journals (Sweden)

Fengling Zhang

2017-01-01

Full Text Available We report a battery-powered, paper-based electrochromic array for visualized electrochemical sensing. The paper-based sensing system consists of six parallel electrochemical cells, which are powered by an aluminum-air battery. Each single electrochemical cell uses a Prussian Blue spot electrodeposited on an indium-doped tin oxide thin film as the electrochromic indicator. Each electrochemical cell is preloaded with increasing amounts of analyte. The sample activates the battery for the sensing. Both the preloaded analyte and the analyte in the sample initiate the color change of Prussian Blue to Prussian White. With a reaction time of 60 s, the number of electrochemical cells with complete color changes is correlated to the concentration of analyte in the sample. As a proof-of-concept analyte, lactic acid was detected semi-quantitatively using the naked eye.

TiO 2 counter electrode for electrochromic devices

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 38; Issue 2 ... The band gap energy decreases (g) from 3.45 eV for pristine CeO2 to 2.98–3.09 eV ... as counter electrode in electrochromic smart windows in which they are able to retain ...

Electrochromic artificial muscles based on nanoporous metal-polymer composites

NARCIS (Netherlands)

Detsi, E.; Onck, P. R.; De Hosson, J. T. M.

2013-01-01

This work shows that a nano-coating of electrochromic polymer grown onto the ligaments of nanoporous gold causes reversible dimensional and color changes during electrochemical actuation. This combination of electromechanical and optical properties opens additional avenues for the applications of

Li+ ions diffusion into sol-gel V2O5 thin films: electrochromic properties

Science.gov (United States)

Benmoussa, M.; Outzourhit, A.; Bennouna, A.; Ihlal, A.

2009-10-01

V{2}O{5} thin films were prepared by the sol-gel spin coating process. The Li+ ions insertion effect on optical and electrochromic properties of those films was studied. The diffusion coefficient was calculated using both cyclic voltammograms and chronoamperometric curves. The amount x of Li+ ions in LixV{2}O{5} was also calculated. Finally, the electrochromic performance evolution characteristics such as the reversibility, coloration efficiency, coloration memory stability and response time were studied.

Synthesis and Performance of Highly Stable Star-Shaped Polyaniline Electrochromic Materials with Triphenylamine Core

Science.gov (United States)

Xiong, Shanxin; Li, Shuaishuai; Zhang, Xiangkai; Wang, Ru; Zhang, Runlan; Wang, Xiaoqin; Wu, Bohua; Gong, Ming; Chu, Jia

2018-02-01

The molecular architecture of conducting polymers has a significant impact on their conjugated structure and electrochemical properties. We have investigated the influence of star-shaped structure on the electrochemical and electrochromic properties of polyaniline (PANI). Star-shaped PANI (SPANI) was prepared by copolymerization of aniline with triphenylamine (TPA) using an emulsion polymerization method. With addition of less than 4.0 mol.% TPA, the resulting SPANI exhibited good solubility in xylene with dodecylbenzenesulfonic acid (DBSA) as doping acid. The structure and thermal stability of the SPANI were characterized using Fourier-transform infrared spectroscopy, Raman spectroscopy, and thermogravimetric analysis, and the electrochemical behavior was analyzed by cyclic voltammetry (CV). The electrochromic properties of SPANI were tested using an electrochemical workstation combined with an ultraviolet-visible (UV-Vis) spectrometer. The results show that, with increasing TPA loading, the thermal stability of SPANI increased. With addition of 4.0 mol.% TPA, the weight loss of SPANI was 36.9% at 700°C, much lower than the value of 71.2% for PANI at the same temperature. The low oxidation potential and large enclosed area of the CV curves indicate that SPANI possesses higher electrochemical activity than PANI. Enhanced electrochromic properties including higher optical contrast and better electrochromic stability of SPANI were also obtained. SPANI with 1.6 mol.% TPA loading exhibited the highest optical contrast of 0.71, higher than the values of 0.58 for PANI, 0.66 for SPANI-0.4%, or 0.63 for SPANI-4.0%. Overdosing of TPA resulted in slow switching speed due to slow ion transport in short branched chains of star-shaped PANI electrochromic material. Long-term stability testing confirmed that all the SPANI-based devices exhibited better stability than the PANI-based device.

On-chip electrochromic micro display for a disposable bio-sensor chip

Science.gov (United States)

Zhu, Yanjun; Tsukamoto, Takashiro; Tanaka, Shuji

2017-12-01

This paper reports an on-chip electrochromic micro display made of polyaniline (PANi) which can be easily made on a CMOS chip. Micro-patterned PANi thin films were selectively deposited on pre-patterned microelectrodes by using electrodeposition. The optimum conditions for deposition and electrochromism were investigated. An 8-pixel on-chip micro display was made on a Si chip. The color of each PANi film could be independently but simultaneously controlled, which means any 1-byte digital data could be displayed on the display. The PANi display had a response time as fast as about 100 ms, which means the transfer data rate was as fast as 80 bits per second.

Preparation, Characterization, and Electrochromic Properties of Nanocellulose-Based Polyaniline Nanocomposite Films.

Science.gov (United States)

Zhang, Sihang; Sun, Gang; He, Yongfeng; Fu, Runfang; Gu, Yingchun; Chen, Sheng

2017-05-17

On the basis of nanocellulose obtained by acidic swelling and ultrasonication, rodlike nanocellulose/polyaniline nanocomposites with a core-shell structure have been prepared via in situ polymerization. Compared to pure polyaniline, the nanocomposites show superior film-forming properties, and the prepared nanocomposite films demonstrate excellent electrochemical and electrochromic properties in electrolyte solution. Nanocomposite films, especially the one prepared with 40% polyaniline coated nanocomposite, exhibited faster response time (1.5 s for bleaching and 1.0 s for coloring), higher optical contrast (62.9%), higher coloration efficiency (206.2 cm 2 /C), and more remarkable switching stability (over 500 cycles). These novel nanocellulose-based nanorod network films are promising novel electrochromic materials with excellent properties.

Assembly of tungsten oxide nanobundles and their electrochromic properties

International Nuclear Information System (INIS)

Chang Xueting; Sun Shibin; Li Zhenjiang; Xu Xiao; Qiu Yanyan

2011-01-01

Lenticular W 18 O 49 nanobundles composed of ultra-thin nanowires with diameters of 5-10 nm have been synthesized through a simple solvothermal method with hexachloride as precursor and mixed cyclohexanol and ethanol as solvent. Electrochromic films were prepared by assembling the W 18 O 49 nanobundle suspension onto tin-doped indium oxide (ITO) coated glass. Results showed that self-assembly of the W 18 O 49 nanobundles was strongly influenced by the solvents employed to disperse the nanobundles. The W 18 O 49 nanobundles coated films exhibited excellent electrochromic stability and reversibility. The W 18 O 49 nanobundle films also showed much higher charge-insertion density compared with the WO 3 nanorod film, which may be due to the ultrathin feature of single nanowires constituting the nanobundles, unique oxygen vacancies of monoclinic W 18 O 49 , and the highly ordered assembly of the nanobundles.

Electrochromic Windows: Process and Fabrication Improvements for Lower Total Costs

Energy Technology Data Exchange (ETDEWEB)

Mark Burdis; Neil Sbar

2007-03-31

The overall goal with respect to the U.S. Department of Energy (DOE) is to achieve significant national energy savings through maximized penetration of EC windows into existing markets so that the largest cumulative energy reduction can be realized. The speed with which EC windows can be introduced and replace current IGU's (and current glazings) is clearly a strong function of cost. Therefore, the aim of this project was to investigate possible improvements to the SageGlass{reg_sign} EC glazing products to facilitate both process and fabrication improvements resulting in lower overall costs. The project was split into four major areas dealing with improvements to the electrochromic layer, the capping layer, defect elimination and general product improvements. Significant advancements have been made in each of the four areas. These can be summarized as follows: (1) Plasma assisted deposition for the electrochromic layer was pursued, and several improvements made to the technology for producing a plasma beam were made. Functional EC devices were produced using the new technology, but there are still questions to be answered regarding the intrinsic properties of the electrochromic films produced by this method. (2) The capping layer work was successfully implemented into the existing SageGlass{reg_sign} product, thereby providing a higher level of transparency and somewhat lower reflectivity than the 'standard' product. (3) Defect elimination is an ongoing effort, but this project spurred some major defect reduction programs, which led to significant improvements in yield, with all the implicit benefits afforded. In particular, major advances were made in the development of a new bus bar application process aimed at reducing the numbers of 'shorts' developed in the finished product, as well as making dramatic improvements in the methods used for tempering the glass, which had previously been seen to produce a defect which appeared as a

Synergistic tungsten oxide/organic framework hybrid nanofibers for electrochromic device application

Science.gov (United States)

Dulgerbaki, Cigdem; Komur, Ali Ihsan; Nohut Maslakci, Neslihan; Kuralay, Filiz; Uygun Oksuz, Aysegul

2017-08-01

We report the first successful applications of tungsten oxide/conducting polymer hybrid nanofiber assemblies in electrochromic devices. Poly(3,4-ethylenedioxythiophene)/tungsten oxide (PEDOT/WO3) and polypyrrole/tungsten oxide (PPy/WO3) composites were prepared by an in situ chemical oxidative polymerization of monomers in different ionic liquids; 1-butyl-3-methylimidazolium tetrafluoroborate (BMIMBF4), 1-butyl-3-methylimidazolium hexafluorophosphate (BMIMPF6), 1-butyl-3-methylimidazolium bis(trifluoromethylsulfonyl) imide (BMIMTFSI) and 1-butyl-1-methylpyrrolidinium bis(trifluoromethylsulfonyl) imide (BMPTFSI). Electrospinning process was used to form hybrid nanofibers from chemically synthesized nanostructures. The electrospun hybrid samples were compared from both morphological and electrochemical perspectives. Importantly, deposition of nanofibers from chemically synthesized hybrids can be achieved homogenously, on nanoscale dimensions. The morphologies of these assemblies were evaluated by SEM, whereas their electroactivity was characterized by cyclic voltammetry. Electrochromic devices made from hybrid nanofiber electrodes exhibited highest chromatic contrast of 37.66% for PEDOT/WO3/BMIMPF6, 40.42% for PPy/WO3/BMIMBF4 and show a strong electrochromic color change from transparent to light brown. Furthermore, the nanofiber devices exhibit outstanding stability when color switching proceeds, which may ensure a versatile platform for color displays, rear-view mirrors and smart windows.

DNA Based Electrochromic and Photovoltaic Cells

Science.gov (United States)

2012-01-01

using deoxyribonucleic acid complex as an electron blocking layer App. Phys. Lett. 88 (2006) 171109. 23. F.H.C. Crick , J.D. Watson . The complementary...9550-09-1-0647 final 01-09-2009 ; 30-11-2011 DNA Based Electrochromic and Photovoltaic Cells FA 9550-09-1-0647 Pawlicka, Agnieszka, J. Instituto de...Available. DNA is an abundant natural product with very good biodegradation properties and can be used to obtain gel polymer electrolytes (GPEs) with high

Large-scale fabrication of pseudocapacitive glass windows that combine electrochromism and energy storage.

Science.gov (United States)

Yang, Peihua; Sun, Peng; Chai, Zhisheng; Huang, Langhuan; Cai, Xiang; Tan, Shaozao; Song, Jinhui; Mai, Wenjie

2014-10-27

Multifunctional glass windows that combine energy storage and electrochromism have been obtained by facile thermal evaporation and electrodeposition methods. For example, WO3 films that had been deposited on fluorine-doped tin oxide (FTO) glass exhibited a high specific capacitance of 639.8 F g(-1). Their color changed from transparent to deep blue with an abrupt decrease in optical transmittance from 91.3% to 15.1% at a wavelength of 633 nm when a voltage of -0.6 V (vs. Ag/AgCl) was applied, demonstrating its excellent energy-storage and electrochromism properties. As a second example, a polyaniline-based pseudocapacitive glass was also developed, and its color can change from green to blue. A large-scale pseudocapacitive WO3-based glass window (15×15 cm(2)) was fabricated as a prototype. Such smart pseudocapacitive glass windows show great potential in functioning as electrochromic windows and concurrently powering electronic devices, such as mobile phones or laptops. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Assembly of tungsten oxide nanobundles and their electrochromic properties

Energy Technology Data Exchange (ETDEWEB)

Chang Xueting, E-mail: xuetingchang@yahoo.cn [Institute of Marine Materials Science and Engineering, Shanghai Maritime University, Shanghai 200135 (China); College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061 (China); Sun Shibin [Institute of Marine Materials Science and Engineering, Shanghai Maritime University, Shanghai 200135 (China); College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061 (China); Li Zhenjiang; Xu Xiao; Qiu Yanyan [College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061 (China)

2011-04-15

Lenticular W{sub 18}O{sub 49} nanobundles composed of ultra-thin nanowires with diameters of 5-10 nm have been synthesized through a simple solvothermal method with hexachloride as precursor and mixed cyclohexanol and ethanol as solvent. Electrochromic films were prepared by assembling the W{sub 18}O{sub 49} nanobundle suspension onto tin-doped indium oxide (ITO) coated glass. Results showed that self-assembly of the W{sub 18}O{sub 49} nanobundles was strongly influenced by the solvents employed to disperse the nanobundles. The W{sub 18}O{sub 49} nanobundles coated films exhibited excellent electrochromic stability and reversibility. The W{sub 18}O{sub 49} nanobundle films also showed much higher charge-insertion density compared with the WO{sub 3} nanorod film, which may be due to the ultrathin feature of single nanowires constituting the nanobundles, unique oxygen vacancies of monoclinic W{sub 18}O{sub 49}, and the highly ordered assembly of the nanobundles.

Syntheses and electrochromic and fluorescence properties of three double dithienylpyrroles derivatives

International Nuclear Information System (INIS)

Wang Gang; Fu Xiangkai; Huang Jing; Wu Chuanlong; Wu Liu; Deng Jun; Du Qiuliang; Zou Xiaochuan

2011-01-01

Highlights: → Three kinds of double dithienylpyrroles derivatives have been successfully prepared by the Knorr-Paal condensation between 1,4-di(thiophen-2-yl) butane-1,4-dione and aromatic diamines. → Their polymer films were successfully synthesized via electropolymerization. → The polymer films had stable and well-defined reversible redox process, low optical band gap and multicolor electrochromic behavior. → All the monomers and polymers exhibited different intensity emission bands at different wavelengths. - Abstract: Three double dithienylpyrroles derivatives have been successfully prepared by performing a Knorr-Paal condensation between 1,4-di(thiophen-2-yl) butane-1,4-dione and various aromatic diamines. Additionally, their corresponding polymer films were synthesized via electropolymerization. Their electrochemical, spectroelectrochemical and electrochromic behaviors were further investigated by thermogravimetric analysis, scanning electron microscopy, cyclic voltammetry, UV-vis absorption and fluorescence emission spectra. Scanning electron microscopy and thermogravimetric analysis demonstrated that the polymer films possessed homogeneous, compact and smooth layer structures and thermal stabilities (up to nearly 180 deg. C). Cyclic voltammograms and UV-vis absorption spectra studies showed that the polymer films have stable, well-defined, reversible redox processes, low optical band gaps (E g < 2.2 eV) and multicolor electrochromic behaviors. Additionally, the fluorescence spectra study showed that all of the monomers and polymers exhibited different intensity emission bands at different wavelengths.

Fabrication of WO3-based electrochromic displays using solid or gel-like organic electrolytes

International Nuclear Information System (INIS)

Vasilopoulou, M; Aspiotis, G; Kostis, I; Argitis, P; Davazoglou, D

2005-01-01

New all solid-state electrochromic displays were fabricated by chemically vapor depositing and patterning a tungsten oxide film on SnO 2 :F covered glass substrates. Aluminum sheets were used as counter electrodes to form electrochromic displays using solid or gel-like organic electrolytes. These ionically conductive and electronically insulating electrolytes were based on poly(methyl methacrylate) (PMMA) and poly(2-hydrohyethyl methacrylate) (PHEMA) into which phospho-tungstic acid was added at various concentrations. In some devices the electrolyte was formed by addition of photoacid generator into the polymeric matrix and exposure at deep UV light. It was found that displays exhibit an intense, reversible electrochromic effect with reflectivity varying by a factor of five between the uncolored to the colored state. The coloring voltage depends strongly on the polymeric matrix, the thickness of the electrolyte and post-apply baking conditions and is of the order of 6-9 V. The response time was found to be of the order of 500 ms; coloration and bleaching times were comparable

Electrochromism and photocatalysis in dendrite structured Ti:WO3 thin films grown by sputtering

Energy Technology Data Exchange (ETDEWEB)

Karuppasamy, A., E-mail: karuppasamy@psnacet.edu.in

2015-12-30

Graphical abstract: - Highlights: • Dendrite structured Ti doped WO{sub 3} (WTO) thin films are grown by co-sputtering. • Sputtering condition influences structure and surface morphology of WTO films. • Titanium doping and annealing lead to dendritic surface structures in WTO films. • Structural, optical, electrochromic and photocatalytic properties of WTO films. • Enhanced electrochromism and photocatalysis in dendrite structured WTO thin films. - Abstract: Titanium doped tungsten oxide (Ti:WO{sub 3}) thin films with dendrite surface structures were grown by co-sputtering titanium and tungsten in Ar + O{sub 2} atmosphere. Ti:WO{sub 3} thin films were deposited at oxygen flow rates corresponding to pressures in the range 1.0 × 10{sup −3}–5.0 × 10{sup −3} mbar. Argon flow rate and sputtering power densities for titanium (2 W/cm{sup 2}) and tungsten (3 W/cm{sup 2}) were kept constant. Ti:WO{sub 3} films deposited at an oxygen pressure of 5 × 10{sup −3} mbar are found to be better electrochromic and photocatalytic. They have high optical modulation (80% at λ = 550 nm), coloration efficiency (60 cm{sup 2}/C at λ = 550 nm), electron/ion storage and removal capacity (Qc: −22.01 mC/cm{sup 2}, Qa: 17.72 mC/cm{sup 2}), reversibility (80%) and methylene blue decomposition rate (−1.38 μmol/l d). The combined effects of titanium doping, dendrite surface structures and porosity leads to significant enhancement in the electrochromic and photocatalytic properties of Ti:WO{sub 3} films.

Electrochromism and photocatalysis in dendrite structured Ti:WO3 thin films grown by sputtering

International Nuclear Information System (INIS)

Karuppasamy, A.

2015-01-01

Graphical abstract: - Highlights: • Dendrite structured Ti doped WO 3 (WTO) thin films are grown by co-sputtering. • Sputtering condition influences structure and surface morphology of WTO films. • Titanium doping and annealing lead to dendritic surface structures in WTO films. • Structural, optical, electrochromic and photocatalytic properties of WTO films. • Enhanced electrochromism and photocatalysis in dendrite structured WTO thin films. - Abstract: Titanium doped tungsten oxide (Ti:WO 3 ) thin films with dendrite surface structures were grown by co-sputtering titanium and tungsten in Ar + O 2 atmosphere. Ti:WO 3 thin films were deposited at oxygen flow rates corresponding to pressures in the range 1.0 × 10 −3 –5.0 × 10 −3 mbar. Argon flow rate and sputtering power densities for titanium (2 W/cm 2 ) and tungsten (3 W/cm 2 ) were kept constant. Ti:WO 3 films deposited at an oxygen pressure of 5 × 10 −3 mbar are found to be better electrochromic and photocatalytic. They have high optical modulation (80% at λ = 550 nm), coloration efficiency (60 cm 2 /C at λ = 550 nm), electron/ion storage and removal capacity (Qc: −22.01 mC/cm 2 , Qa: 17.72 mC/cm 2 ), reversibility (80%) and methylene blue decomposition rate (−1.38 μmol/l d). The combined effects of titanium doping, dendrite surface structures and porosity leads to significant enhancement in the electrochromic and photocatalytic properties of Ti:WO 3 films.

Studies of solid-state electrochromic devices based on Peo/siliceous hybrids doped with lithium perchlorate

International Nuclear Information System (INIS)

Barbosa, P.C.; Silva, M.M.; Smith, M.J.; Goncalves, A.; Fortunato, E.

2007-01-01

Sol-gel hybrid organic-inorganic networks, doped with a lithium salt, have been used as electrolytes in prototype smart windows. The work described in this presentation is focused on the application of these networks as dual-function electrolyte/adhesive components in solid-state electrochromic devices. The performance of multi-layer electrochromic devices was characterized as a function of the choice of precursor used to prepare the polymer electrolyte component and the guest salt concentration. The prototype devices exhibited good open-circuit memory, coloration efficiency, optical contrast and stability

The correlations of electrochromism and thermochromism of tungsten oxide films studied by slow positron beam

International Nuclear Information System (INIS)

Ma Chuangxin; Zhou Chunlan; Zhang Zhiming; Wang Baoyi; Wei Long

2004-01-01

Electrochromic (EC) and thermochromic (TC) tungsten oxide (WO 3 ) films, deposited by magnetron sputtering and vacuum thermal evaporation, were studied systematically by means of slow positron measurements. The S parameters of colored amorphous WO 3 film and crystalline WO 3 film behaved quite similarly in the processes of thermochromism and electrochromism, little influenced by the different deposition methods. It indicates that the coloration processes under various external conditions are correlated with each other. It also shows that the slow positron beam technique may play a particular role in the study of chromogenic materials. (orig.)

Spectral and optical performance of electrochromic poly(3,4-ethylenedioxythiophene) (PEDOT) deposited on transparent conducting oxide coated glass and polymer substrates

International Nuclear Information System (INIS)

Sindhu, S.; Narasimha Rao, K.; Ahuja, Sharath; Kumar, Anil; Gopal, E.S.R.

2006-01-01

Electrochromic devices utilizing conjugated polymers as electrochromic layers have gained increasing attention owing to their optical properties, fast switching times and contrast ratios. Polyethylenedioxythiophene (PEDOT) is an excellent material from its electrochromic properties, high conductivity and high stability in the doped form. Aqueous dispersions of PEDOT were either spin coated or electro-polymerized on transparent conducting oxide coated glass and polyethylene tetraphthalate (PET) film substrates. The spectro- and opto-electrochemical studies of the films on transparent conducting oxide coated glass/PET substrates were performed. These films have application in the fabrication of electrochromic windows (smart windows). Smart window devices having excellent switching characteristics over wide range of temperature are used for glazing applications. The aerospace industry is interested in the development of visors and windows that can control glare for pilots and passengers, especially if the coatings can be made on curved surfaces and electrically conducting

Variable Emissivity Electrochromics using Ionic Electrolytes and Low Solar Absorptance Coatings, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — This work further developed a highly promising variable emissivity technology for spacecraft thermal control, based on unique conducting polymer (CP) electrochromics...

Electrochromic properties of bipolar pulsed magnetron sputter deposited tungsten–molybdenum oxide films

Energy Technology Data Exchange (ETDEWEB)

Lin, Tai-Nan [Chemical Engineering Division, Institute of Nuclear Energy Research, Taoyuan 325, Taiwan, ROC (China); Lin, Yi Han; Lee, Chin Tan [Department of Electronic Engineering, National Quemoy University, Kinmen 892, Taiwan, ROC (China); Han, Sheng [Center of General Education, National Taichung Institute of Technology, Taichung 404, Taiwan, ROC (China); Weng, Ko-Wei, E-mail: kowei@nqu.edu.tw [Department of Electronic Engineering, National Quemoy University, Kinmen 892, Taiwan, ROC (China)

2015-06-01

There are great interests in electrochromic technology for smart windows and displays over past decades. In this study, the WMoO{sub x} thin films were deposited onto indium tin oxide glass and silicon substrates by pulsed magnetron sputter system with W and Mo targets. The films were deposited with fixed W target power while the variant parameter of Mo target power in the range 50, 100, 150 and 200 W was investigated. The working pressure was fixed at 1.33 Pa with a gas mixture of Ar (30 sccm) and O{sub 2} (15 sccm). The film thickness increased with the Mo target power. Higher plasma power resulted in a crystalline structure which would reduce the electrochromic property of the film. The influence of plasma powers applied to Mo target on the structural, optical and electrochromic properties of the WMoO{sub x} thin films has been investigated. WMoO{sub x} films grown at Mo target powers less than 100 W were found to be amorphous. The films deposited at 150 W, which is the optimal fabrication condition, exhibit better electrochromic properties with high optical modulation, high coloration efficiency and less color memory effect at wavelength 400, 550 and 800 nm. The improvement resulted from the effect of doping Mo has been tested. The maximum ΔT (%) values are 36.6% at 400 nm, 65.6% at 550 nm, and 66.6% at 800 nm for pure WO{sub 3} film. The addition of Mo content in the WMoO{sub x} films provides better resistance to the short wavelength light source and can be used in the concerned application. - Highlights: • WMoO{sub x} films are deposited by pulsed magnetron sputter with pure W and Mo targets. • Mo addition in WMoO{sub x} provides better resistance to short wavelength light source. • WMoO{sub x} films exhibit electrochemical stability in the cycling test.

Variable Emissivity Electrochromics Using Ionic Electrolytes and Low Solar Absorptance Coatings, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — In recent work, this firm developed a highly promising, patented variable emittance technology based on electrochromic Conducting Polymers, with: (1) Thin ( 105...

Electrochromism of solid films of blue form of lutetium phthalocyanine complexe

Energy Technology Data Exchange (ETDEWEB)

Gavrilov, V I; Konstantinov, A P; Luk' yanets, E A; Shelepin, I V

1986-12-01

Results of spectral-electrochemical study on electrochromic films of blue form of tret-butyl-substituted lutetium diphthalocyanine deposited on the surface of an electrode contacting with electrolyte aqueous solution are presented. In the 0.2-1.15 V potential range sweep of the electrode potential is followed by reversible change of the film colour in the following succession: blue reversible green reversible red. Electrochromic properties of the film confirm the corresponding spectral transitions from the initial state to monoelectron-oxidized and further on to the product of two-electron oxidation. Under potential sweeping towards the anode in the 1.4 V range and irreversible wave arises; potential achievement of this wave brings about complete change in the form of j, E-curves. The consequent electrode processes are followed by change in the film colour green - red that is associated witn mechanical fracture of the film.

Electrochromic absorbance changes in relation to electron transport and energy coupling in thylakoid membranes : [Electrochrome absorptie veranderingen in relatie tot elektronentransport en energiekoppeling in thylakoid membranen

NARCIS (Netherlands)

Ooms, J.J.J.

1990-01-01

This thesis deals mainly with the analysis and interpretation of the flash-induced electrochromic absorbance changes in isolated chloroplasts of spinach and pea plants. The amplitude and kinetics of the flash-induced absorbance changes at 518 nm (P515) are discussed in relation to the

Surfactant-assisted ultrasonic spray pyrolysis of nickel oxide and lithium-doped nickel oxide thin films, toward electrochromic applications

Energy Technology Data Exchange (ETDEWEB)

Denayer, Jessica [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Bister, Geoffroy [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Simonis, Priscilla [Laboratory LPS, University of Namur, rue de bruxelles 61, 5000 Namur (Belgium); Colson, Pierre; Maho, Anthony [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Aubry, Philippe [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Vertruyen, Bénédicte [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Henrist, Catherine, E-mail: catherine.henrist@ulg.ac.be [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium); Lardot, Véronique; Cambier, Francis [Environmental and Material Research Association (CRIBC-INISMa), avenue gouverneur cornez 4, 7000 Mons (Belgium); Cloots, Rudi [Group of Research in Energy and Environment for MATerials (GREENMAT), University of Liège, allée de la chimie 3, 4000 Liège (Belgium)

2014-12-01

Highlights: • Surfactant-assisted USP: a novel and low cost process to obtain high quality nickel oxide films, with or without lithium dopant. • Increased uniformity and reduced light scattering thanks to the addition of a surfactant. • Improved electrochromic performance (coloration efficiency and contrast) for lithium-doped films by comparison with the undoped NiO film. - Abstract: Lithium-doped nickel oxide and undoped nickel oxide thin films have been deposited on FTO/glass substrates by a surfactant-assisted ultrasonic spray pyrolysis. The addition of polyethylene glycol in the sprayed solution has led to improved uniformity and reduced light scattering compared to films made without surfactant. Furthermore, the presence of lithium ions in NiO films has resulted in improved electrochromic performances (coloration contrast and efficiency), but with a slight decrease of the electrochromic switching kinetics.

Defect engineering of two-dimensional WO{sub 3} nanosheets for enhanced electrochromism and photoeletrochemical performance

Energy Technology Data Exchange (ETDEWEB)

Zhou, Xiaofang; Zheng, Xiaoli; Yan, Bo; Xu, Tao; Xu, Qun, E-mail: qunxu@zzu.edu.cn

2017-04-01

Highlights: • We establish a facile strategy by solvothermal reaction and hydrogenation to synthesize 2D WO{sub 3} ultrathin nanosheets with abundant oxygen vacancies. • We find that the hydrogenated WO{sub 3} ultrathin nanosheets exhibit outstanding electrochromism properties. • Moreover, the hydrogenated WO{sub 3} nanosheets also exhibit remarkable photocatalytic performance. • The outstanding electrochromism and photoelectrochemical performances are mainly due to increased oxygen vacancies and narrowed band gap. - Abstract: The capability of introduction of oxygen vacancies in a controlled way has emerged as the heart of modern transition metal oxide semiconductor chemistry. As chemical defects, the oxygen vacancies have been proposed as electron donors, which are prone to increase carrier density and promote charge carrier separation. Herein, we have successfully prepared 2D WO{sub 3} ultrathin nanosheets with abundant surface oxygen vacancies by a combination of facile solvothermal reaction and hydrogenation method. The resultant hydrogenated WO{sub 3} ultrathin nanosheets exhibit remarkable electrochromism and photocatalytic performances compared with the non-hydrogenated samples, mainly due to their increased oxygen vacancies, narrowed band gap coupled with fast charge transfer and enhanced adsorption of visible light.

Improved Electrochromic Characteristics of a Honeycomb-Structured Film Composed of NiO.

Science.gov (United States)

Yang, Hyeeun; Lee, Yulhee; Kim, Dong In; Seo, Hyeon Jin; Yu, Jung-Hoon; Nam, Sang-Hun; Boo, Jin-Hyo

2018-09-01

Color changes controlled by electronic energies have been studied for many years in order to fabricate energy-efficient smart windows. Reduction and oxidization of nickel oxide under the appropriate voltage can change the color of a window. For a superior nickel oxide (NiO) electrochromic device (ECD), it is important to control the chemical and physical characteristics of the surface. In this study, we applied polystyrene bead templates to nickel oxide films to fabricate a honeycomb-structured electrochromic (EC) layer. We synthesized uniform polystyrene beads using the chemical wet method and placed them on substrates to create honeycomb-structured NiO films. Then, the EC characteristics of the nickel oxide films with a honeycomb structure were evaluated with UV-Visible and cyclic voltammetry. FE-SEM and AFM were used to measure the morphologies of the nanostructures and the efficiencies of the redox reactions related to the specific surface area.

Direct Photopatterning of Electrochromic Polymers

DEFF Research Database (Denmark)

Jensen, Jacob; Dyer, Aubrey L.; Shen, D. Eric

2013-01-01

Propylenedioxythiophene (ProDOT) polymers are synthesized using an oxidative polymerization route that results in methacrylate substituted poly(ProDOTs) having a Mn of 10–20 kDa wherein the methacrylate functionality constitutes from 6 to 60% of the total monomer units. Solutions of these polymers...... show excellent film forming abilities, with thin films prepared using both spray‐casting and spin‐coating. These polymers are demonstrated to crosslink upon UV irradiation at 350 nm, in the presence of an appropriate photoinitiator, to render the films insoluble to common organic solvents....... Electrochemical, spectroelectrochemical, and colorimetric analyses of the crosslinked polymer films are performed to establish that they retain the same electrochromic qualities as the parent polymers with no detriment to the observed properties. To demonstrate applicability for multi‐film processing...

Fully Screen-Printed, Large-Area, and Flexible Active-Matrix Electrochromic Displays Using Carbon Nanotube Thin-Film Transistors.

Science.gov (United States)

Cao, Xuan; Lau, Christian; Liu, Yihang; Wu, Fanqi; Gui, Hui; Liu, Qingzhou; Ma, Yuqiang; Wan, Haochuan; Amer, Moh R; Zhou, Chongwu

2016-11-22

Semiconducting single-wall carbon nanotubes are ideal semiconductors for printed electronics due to their advantageous electrical and mechanical properties, intrinsic printability in solution, and desirable stability in air. However, fully printed, large-area, high-performance, and flexible carbon nanotube active-matrix backplanes are still difficult to realize for future displays and sensing applications. Here, we report fully screen-printed active-matrix electrochromic displays employing carbon nanotube thin-film transistors. Our fully printed backplane shows high electrical performance with mobility of 3.92 ± 1.08 cm 2 V -1 s -1 , on-off current ratio I on /I off ∼ 10 4 , and good uniformity. The printed backplane was then monolithically integrated with an array of printed electrochromic pixels, resulting in an entirely screen-printed active-matrix electrochromic display (AMECD) with good switching characteristics, facile manufacturing, and long-term stability. Overall, our fully screen-printed AMECD is promising for the mass production of large-area and low-cost flexible displays for applications such as disposable tags, medical electronics, and smart home appliances.

Aluminum doped nickel oxide thin film with improved electrochromic performance from layered double hydroxides precursor in situ pyrolytic route

International Nuclear Information System (INIS)

Shi, Jingjing; Lai, Lincong; Zhang, Ping; Li, Hailong; Qin, Yumei; Gao, Yuanchunxue; Luo, Lei; Lu, Jun

2016-01-01

Electrochromic materials with unique performance arouse great interest on account of potential application values in smart window, low-power display, automobile anti-glare rearview mirror, and e-papers. In this paper, high-performing Al-doped NiO porous electrochromic film grown on ITO substrate has been prepared via a layered double hydroxides(LDHs) precursor in situ pyrolytic route. The Al 3+ ions distributed homogenously within the NiO matrix can significantly influence the crystallinity of Ni-Al LDH and NiO:Al 3+ films. The electrochromic performance of the films were evaluated by means of UV–vis absorption spectroscopy, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronoamperometry(CA) measurements. In addition, the ratio of Ni 3+ /Ni 2+ also varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range (58.4%), fast switching speed (bleaching/coloration times are 1.8/4.2 s, respectively) and excellent durability (30% decrease after 2000 cycles). The improved performance was owed to the synergy of large NiO film specific surface area and porous morphology, as well as Al doping stifled the formation of Ni 3+ making bleached state more pure. This LDHs precursor pyrolytic method is simple, low-cost and environmental benign and is feasible for the preparation of NiO:Al and other Al-doped oxide thin film. - Graphical abstract: The ratio of Ni 3+ /Ni 2+ varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range, fast switching speed and excellent durability. Display Omitted

Multicolored, Low-Voltage-Driven, Flexible Organic Electrochromic Devices Based on Oligomers.

Science.gov (United States)

Wan, Zhijun; Zeng, Jinming; Li, Hui; Liu, Ping; Deng, Wenji

2018-04-20

In this study, a series of organic conjugated oligomers containing 3,4-ethylenedioxythiophene (EDOT) and aromatic groups are synthesized, which are as follows: 2,5-di(methyl benzoate)-3,4-ethylenedioxy-thiophene (1EDOT-2B-COOCH 3 ), 5,5'-di(methyl benzoate)-2,2'-bi(3,4-ethylenedioxythiophene) (2EDOT-2B-COOCH 3 ), 5,5″-di(methyl benzoate)-2,2':5',2″-ter(3,4-ethylenedioxythiophene) (3EDOT-2B-COOCH 3 ), and 5,5″'-di(methyl benzoate)-2,2':5',2″: 5″,2″'-quater(3,4-ethylenedioxythiophene) (4EDOT-2B-COOCH 3 ). Using these oligomers as active materials, flexible organic electrochromic devices are fabricated. The device structure is indium tin oxide-PET plastic slide (ITO-PET)/active layer/conducting gel/ITO-PET, and the electrochromic properties of oligomers are investigated. These oligomers exhibit reversible color changes upon electrochemical doping and dedoping. The highest optical contrast is exhibited by 4EDOT-2B-COOCH 3 , which is 75.2% at 700 nm. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electrochemical polymerization of 9-fluorenecarboxylic acid and its electrochromic device application

International Nuclear Information System (INIS)

Bezgin, Buket; Cihaner, Atilla; Onal, Ahmet M.

2008-01-01

Poly(9-fluorenecarboxylic acid) (PFCA) was synthesized by electrochemical oxidation of 9-fluorenecarboxylic acid (FCA) using a mixture of nitromethane and boron trifluoride diethyl etherate as the solvent and tetrabutylammonium tetrafluoroborate as the supporting electrolyte. An insoluble and conducting brownish-orange film was deposited on the electrode surface, both during repetitive cycling and constant potential electrolysis at 1.15 V. Characterization of the polymer film has been carried out using Fourier Transform Infrared spectroscopy technique and thermal behavior was studied via thermal gravimetric analysis. Structural analysis showed that the polymerization of FCA occurred at 2,7-position. Spectroelectrochemical behavior of the polymer film on indium tin oxide working electrode was studied by recording the electronic absorption spectra, in-situ, in monomer-free electrolytic solution at different potentials and it is found that the PFCA film can be reversibly cycled between 0.0 V and 1.2 V. Furthermore, a dual type electrochromic device based on PFCA was constructed and its spectroelectrochemical properties were investigated. The electrochromic device exhibits color change from transparent to dark blue with a good open circuit memory

Fast Switching Electrochromic Devices Containing Optimized BEMA/PEGMA Gel Polymer Electrolytes

Directory of Open Access Journals (Sweden)

N. Garino

2013-01-01

Full Text Available An optimized thermoset gel polymer electrolyte based on Bisphenol A ethoxylate dimethacrylate and Poly(ethylene glycol methyl ether methacrylate (BEMA/PEGMA was prepared by facile photo-induced free radical polymerisation technique and tested for the first time in electrochromic devices (ECD combining WO3 sputtered on ITO as cathodes and V2O5 electrodeposited on ITO as anodes. The behaviour of the prepared ECD was investigated electrochemically and electro-optically. The ECD transmission spectrum was monitored in the visible and near-infrared region by varying applied potential. A switching time of ca. 2 s for Li+ insertion (coloring and of ca. 1 s for Li+ de-insertion (bleaching were found. UV-VIS spectroelectrochemical measurements evidenced a considerable contrast between bleached and colored state along with a good stability over repeated cycles. The reported electrochromic devices showed a considerable enhancement of switching time with respect to the previously reported polymeric ECD indicating that they are good candidates for the implementation of intelligent windows and smart displays.

Electrochromic properties of poly (1-(phenyl)-2,5-di(2-thienyl)-1H-pyrrole-co-3,4-ethylenedioxy thiophene) and its application in electrochromic devices

Science.gov (United States)

Tarkuc, S.; Sahmetlioglu, E.; Tanyeli, C.; Akhmedov, I. M.; Toppare, L.

2008-06-01

Electrochemical copolymerization of 1-(phenyl)-2,5-di(2-thienyl)-1H-pyrrole (PTP) with 3,4-ethylenedioxy thiophene (EDOT) was carried out in acetonitrile (AN)/NaClO4/LiClO4 (0.1 M) solvent-electrolyte couple via potentiodynamic electrolysis. Characterizations of the resulting copolymer were performed via cyclic voltammetry (CV), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM), and spectroelectrochemical analysis. Spectroelectrochemical analyses show that the copolymer of PTP with EDOT has an electronic band gap (due to π to π∗ transition) of 1.9 eV at 480 nm, with a claret red in the fully reduced form and a blue color in the fully oxidized form. Via kinetic studies, the optical contrast (ΔT %) was found to be 8% for P(PTP-co-EDOT). Results showed that the time required to reach 95% of the ultimate transmittance was 1.7 s for the copolymer. The P(PTP-co-EDOT) film was used to construct a dual type polymer electrochromic device (ECDs) with poly(3,4-ethylenedioxy thiophene) (PEDOT). Spectroelectrochemistry, electrochromic switching and open circuit memory of the device were investigated.

Electrocolorimetry of electrochromic materials on flexible ITO electrodes

Energy Technology Data Exchange (ETDEWEB)

Pinheiro, Carlos [Requimte, Dep. Quimica, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); YDreams, Madan Parque, Quinta da Torre, 2829-516 Caparica (Portugal); Parola, A.J.; Pina, F. [Requimte, Dep. Quimica, FCT, Universidade Nova de Lisboa, 2829-516 Caparica (Portugal); Fonseca, J.; Freire, C. [Requimte, Dep. Quimica, Faculdade de Ciencias, Universidade do Porto, Rua do Campo Alegre, 4169-007 Porto (Portugal)

2008-08-15

Electrochromic materials are characterized by their colour changes upon applied voltage. Colour can mean many things: a certain kind of light, its effect on the human eye, or the result of this effect in the mind of the viewer. Since the electrochromic materials are developed towards real life applications it is relevant to characterize them with the usual commercial colour standards. A colorimetric study of electrogenerated Prussian blue and electrogenerated polymers based on salen-type complexes of Cu(II), Ni(II) and Pd(II) deposited over transparent flexible electrodes of polyethylene terephthalate coated with indium tin oxide (PET/ITO electrodes) was carried out using the CIELAB coordinates. A cuvette with a designed adapter to allow potentiostatic control was placed on an integrating sphere installed in the sample compartment of a spectrophotometer to run the colorimetric measurements. The colour evolution in situ was measured through the transmittance of the films by potentiostatic control. Chronocoulometry/chronoabsorptometry was used to evaluate maximum coloration efficiencies for the coloration step: 184 (Pd), 161 (Cu) and 83 cm{sup 2}/C (Ni) and for bleaching: 199 (Pd), 212 (Cu) and 173 cm{sup 2}/C (Ni) of the Pd, Cu and Ni polymer films, respectively. The Prussian Blue/Prussian White states over the PET/ITO films were relatively reversible while the reversibility and stability of the polymers based on the metals salen-type complexes depends on the metal, Pd being the most stable. (author)

Spray deposited CeO2–TiO2 counter electrode for electrochromic ...

Indian Academy of Sciences (India)

application in smart window technology. The technological requirement of smart windows includes the electrochromic working electrode and ion storage layer that should be optically passive after intercalation/deintercalation process. There are only few materials which are used as an optically passive counter electrode with ...

Fe(II) and Co (II) complexes of (4-(4-bromophenyl)-[2,2'-bipyridine]-6-carboxylic acid) synthesis, characterization and electrochromic studies

International Nuclear Information System (INIS)

Saba, A.; Maqsood, Z.T.; Wasim, A.A.; Basha, F.Z.

2017-01-01

In this study novel complexes of substituted bipyridine (4-(4-bromophenyl)-[2,2'-bipyridine]-6-carboxylic acid) with Fe/sup +2/ and Co/sup +2/ were synthesized and characterized by different physical, analytical and spectral techniques which includes /sup 1/ H-NMR, MALDI-MS, FTIR, UV-VIS Spectrophotometry, CHN analysis and conductometry. Mole ratio method revealed that both complexes satisfied ML2 stoichiometry. Other characterization studies showed that substituted bipyridine acted as a tridentate ligand, with two pyridine N and one carboxylic O atom as binding sites per ligand molecule. The complexes were found octahedral, neutral and possessed fairly high molar absorptivities in visible region. Electrochromic studies revealed that Fe (II) complex had relatively good electrochromic properties with a reversible color change from blue to pale yellow. Co (II) complex, however, did not show significant electrochromic properties in the visible region. (author)

Low-potential electrosynthesis of novel electroactive poly(9-fluorenemethanol) and its electrochromic and blue-light-emitting properties

International Nuclear Information System (INIS)

Zhang, Shimin; Qin, Leiqiang; Lu, Baoyang; Xu, Jingkun

2013-01-01

Highlights: ► The electropolymerization of 9-fluorenemethanol (FMO) was reported. ► Semiconducting poly(9-fluorenemethanol) (PFMO) film was electrosynthesized. ► PFMO shows favorable solubility and good redox activity and stability. ► PFMO exhibits electrochromic nature from pale brown to dark blue. ► PFMO is highly fluorescent with its emission at 418 nm and a quantum yield of 0.52. -- Abstract: In this paper we describe the electropolymerization of 9-fluorenemethanol (FMO) in boron trifluoride diethyl etherate, which leads to low-potential electrodeposition of semiconducting poly(9-fluorenemethanol) (PFMO) film under optimized conditions. The as-formed PFMO film shows favorable solubility in common organic solvents, good redox activity and stability with a conductivity of 10 −2 S cm −1 , good thermal stability, and uniform morphology. Besides, PFMO exhibits electrochromic nature with its color changing from pale brown in its reduced form to dark blue upon oxidation, but its electrochromic performances are relatively poor. Fluorescence spectral studies demonstrated that soluble PFMO is highly fluorescent with its maximum emission at 418 nm and a quantum yield of 0.52, and it can emit bright blue light under 365 nm UV light irradiation

Solar driven electrochromic photoelectrochemical fuel cells for simultaneous energy conversion, storage and self-powered sensing.

Science.gov (United States)

Wang, Yanhu; Zhang, Lina; Cui, Kang; Xu, Caixia; Li, Hao; Liu, Hong; Yu, Jinghua

2018-02-15

One solar-driven electrochromic photoelectrochemical fuel cell (PFC) with highly efficient energy conversion and storage is easily constructed to achieve quantitative self-powered sensing. Layered bismuth oxyiodide-zinc oxide nanorod arrays (ZnO@BiOI NRA) with a core/shell p-n heterostructure are fabricated as the photoanode with electrochromic Prussian blue (PB) as the cathode. The core/shell p-n heterostructure for the ZnO@BiOI photoanode can effectively boost the photoelectrochemical (PEC) performance through the improvement of photon absorption and charge carrier separation. The optimal assembled PFC yields an open-circuit voltage (V OC ) of 0.48 V with the maximum power output density (P max ) as high as 155 μW cm -2 upon illumination. Benefitting from the interactive color-changing behavior of PB, the cathode not only exhibits cathodic catalytic activity in the PFC but also serves as an electrochromic display for self-powered sensing. The as-constructed PFC possesses multiple readable signal output nanochannels through the maximum power output density (P max ) of the PFC or the color change of PB. Meanwhile, the dual-signal-output makes the as-constructed self-powered sensor highly available in various operations demands with the enhanced reliability. With the advantages of high efficiency of PFCs, unique assay ability, and broad environmental suitability, the constructed self-powered platform shows broad application prospects as an integrated smart analytical device.

Electrochromic characteristics of a nickel borate thin film investigated by in situ XAFS and UV/vis spectroscopy

International Nuclear Information System (INIS)

Yoshida, Masaaki; Iida, Tsuyoshi; Mineo, Takehiro

2014-01-01

The electrochromic transition of a nickel borate thin film between colorless and brown was examined by means of in situ XAFS and UV/vis spectroscopy. The XAFS spectra showed that the average valence state of the nickel species in the film changed from +2.1 to +3.8 following the application of an electrode potential. Additionally, a broad peak at 700 nm was observed during in situ UV/vis absorption measurements on the application of a positive potential. These results suggest that the nickel borate film reversibly forms a NiOOH structure with a domain size of several nanometers during the electrochromic reaction. (author)

Electrochromic Type E-Paper Using Poly(1H-Thieno[3,4-d]Imidazol-2(3H-One Derivatives by a Novel Printing Fabrication Process

Directory of Open Access Journals (Sweden)

Kirihiro Nakano

2011-12-01

Full Text Available In this study, we report poly(1H-thieno[3,4-d]imidazol-2(3H-one (pTIO derivatives for an electrochromic (EC type e-paper and its novel printing fabrication process. pTIO is a kind of conductive polymer (CP s which are known as one of the EC materials. The electrochromism of pTIO is unique, because its color in doped state is almost transparent (pale gray. A transparent state is required to show a white color in a see-through view of an EC type e-paper. An electrochromism of CP has a good memory effect which is applicable for e-paper. The corresponding monomers of CP are able to be polymerized with an electrochemical method, which be made good use of for the fabrication process of e-paper. pTIO derivatives are copolymerized with other pi-conjugated X unit, which adjusts the color of electrochromism. Finally, we fabricated a segment matrix EC display using pTIO derivatives by ink-jet printing.

Micro-structured electrochromic device based on poly(3,4-ethylenedioxythiophene)

International Nuclear Information System (INIS)

Deutschmann, T; Oesterschulze, E

2013-01-01

Recent developments in consumer electronics, e.g. smartphones, tablet PCs or compact cameras, demand the development of very compact, active, optical microsystems. Because of their low power consumption, low operation voltage and cheap fabrication, voltage-controlled electrochromic devices (ECDs) based on polymer materials are promising candidates. However, the broad application of ECDs is still hindered by crucial technological obstacles. In this paper, we address two main issues: the structuring of the electrochromic material (ECM) and its underlying transparent conductive electrode on a microscale and additionally, the assembly of the ECD as an electrochemical cell with the challenges of airtight sealing, appropriate chemical stability, electrical insulation and the necessity of defining a compartment to hold the liquid electrolyte inside the cell. We first introduce a technological sequence consisting of batch processes (UV lithography and dry and wet etching) to render the microscale structuring of the ECM possible. Furthermore, we exploit the outstanding properties of the thick film dry photoresist Ordyl SY 300 to complete the assembly of ECDs with single-layer technology. As a proof of principle, we present the first results of an ECD device based on a poly(3,4-ethylenedioxythiophene) (PEDOT) material that works as an aperture stop with three coaxial segments, each individually controlled by an external voltage. (paper)

Electrochromism: basis and application of nanomaterials in development of high performance electrodes; Eletrocromismo: fundamentos e a aplicacao de nanomateriais no desenvolvimento de eletrodos de alto desempenho

Energy Technology Data Exchange (ETDEWEB)

Quintanilha, Ronaldo C.; Rocha, Igor; Vichessi, Raquel B.; Lucht, Emili; Naidek, Karine; Winnischofer, Herbert; Vidotti, Marcio [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil). Departamento de Quimica

2014-07-01

This review deals with the basis and novel trends in electrochromism, describing the basic aspects and methodologies employed for the construction and analyses of different modified electrodes. The work presents the classic materials used for the construction of electrochromic electrodes, such as WO{sub 3} and a view on the basic concepts of chromaticity as a useful approach for analyzing colorimetric results. The report also addresses how the incorporation of nanomaterials and the consequent novel modification of electrodes have furthered this area of science, producing electrochromic electrodes with high performance, high efficiency and low response times. (author)

Modelling of the solid state electrochromic system WO/sub 3//HSbO/sub 3/ x 2H/sub 2/O/Ni(OH)/sub 2/

Energy Technology Data Exchange (ETDEWEB)

Lagzdons, J L; Bajars, G E; Lusis, A R [AN Litovskoj SSR, Vilnyus. Inst. Fiziki Poluprovodnikov

1984-08-16

The problem of compatibility of electrochromic materials (ECM) with the solid electrolyte and the selection of solid electrolytes has been studied by means of modelling. The model electrochromic system (ECS) containing cathodically coloring ECM (WO/sub 3/), anodically coloring ECM (Ni(OH)/sub 2/), and a solid proton electrolyte (HSbO/sub 3/ x 2H/sub 2/O), as well as ECS containing H/sub x/WO/sub 3/ as counterelectrode has been investigated by the aid of cyclic voltammograms. Results show the compatibility of both the cathodic (WO/sub 3/) and anodic (Ni(OH)/sub 2/) ECM with solid proton electrolyte. Effective electrochromic devices can be worked out on their basis.

Energy Efficient Electrochromic Windows Incorporating Ionic Liquids

Energy Technology Data Exchange (ETDEWEB)

Cheri Boykin; James Finley; Donald Anthony; Julianna Knowles; Richard Markovic; Michael Buchanan; Mary Ann Fuhry; Lisa Perrine

2008-11-30

One approach to increasing the energy efficiency of windows is to control the amount of solar radiation transmitted through a window by using electrochromic technology. What is unique about this project is that the electrochromic is based on the reduction/oxidation reactions of cathodic and anodic organic semi-conducting polymers using room temperature ionic liquids as ion transport electrolytes. It is believed that these types of coatings would be a lower cost alternative to traditional all inorganic thin film based electrochromic technologies. Although there are patents1 based on the proposed technology, it has never been reduced to practice and thoroughly evaluated (i.e. durability and performance) in a window application. We demonstrate that by using organic semi-conductive polymers, specific bands of the solar spectrum (specifically visible and near infrared) can be targeted for electrochemical variable transmittance responsiveness. In addition, when the technology is incorporated into an insulating glass unit, the energy parameters such as the solar heat gain coefficient and the light to solar gain ratio are improved over that of a typical insulating glass unit comprised of glass with a low emissivity coating. A minimum of {approx}0.02 quads of energy savings per year with a reduction of carbon emissions for electricity of {approx}320 MKg/yr benefit is achieved over that of a typical insulating glass unit including a double silver low-E coating. Note that these values include a penalty in the heating season. If this penalty is removed (i.e. in southern climates or commercial structures where cooling is predominate year-round) a maximum energy savings of {approx}0.05 quad per year and {approx}801 MKg/yr can be achieved over that of a typical insulating glass unit including a double silver low-E coating. In its current state, the technology is not durable enough for an exterior window application. The primary downfall is that the redox chemistry fails to

Sunlight-charged electrochromic battery based on hybrid film of tungsten oxide and polyaniline

Science.gov (United States)

Chang, Xueting; Hu, Ruirui; Sun, Shibin; Liu, Jingrong; Lei, Yanhua; Liu, Tao; Dong, Lihua; Yin, Yansheng

2018-05-01

Electrochromic (EC) energy storage devices that could realize the multifunctional integration of energy storage and electrochromism have gained much recent attention. Herein, an EC battery based on the hybrid film of W18O49 and polyaniline (PANI) is developed and assembled, which integrates energy storage and EC functions in one device. The W18O49/PANI-EC battery delivers a discharging capacity of 52.96 mA h g-1, which is about two times higher than that of the W18O49-EC battery. Sunlight irradiation could greatly promote the oxidation reactions of both W18O49 and PANI during the charging process of the W18O49/PANI-EC battery, thus effectively accelerating the charging rate. This work provides a green, convenient, environmentally friendly, and cost-free charging strategy for the EC energy systems and could further advance the development of the multifunctional EC devices based on the organic/inorganic composites.

Aluminum doped nickel oxide thin film with improved electrochromic performance from layered double hydroxides precursor in situ pyrolytic route

Energy Technology Data Exchange (ETDEWEB)

Shi, Jingjing; Lai, Lincong; Zhang, Ping; Li, Hailong; Qin, Yumei; Gao, Yuanchunxue; Luo, Lei; Lu, Jun, E-mail: lujun@mail.buct.edu.cn

2016-09-15

Electrochromic materials with unique performance arouse great interest on account of potential application values in smart window, low-power display, automobile anti-glare rearview mirror, and e-papers. In this paper, high-performing Al-doped NiO porous electrochromic film grown on ITO substrate has been prepared via a layered double hydroxides(LDHs) precursor in situ pyrolytic route. The Al{sup 3+} ions distributed homogenously within the NiO matrix can significantly influence the crystallinity of Ni-Al LDH and NiO:Al{sup 3+} films. The electrochromic performance of the films were evaluated by means of UV–vis absorption spectroscopy, cyclic voltammetry (CV), electrochemical impedance spectroscopy (EIS), and chronoamperometry(CA) measurements. In addition, the ratio of Ni{sup 3+}/Ni{sup 2+} also varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range (58.4%), fast switching speed (bleaching/coloration times are 1.8/4.2 s, respectively) and excellent durability (30% decrease after 2000 cycles). The improved performance was owed to the synergy of large NiO film specific surface area and porous morphology, as well as Al doping stifled the formation of Ni{sup 3+} making bleached state more pure. This LDHs precursor pyrolytic method is simple, low-cost and environmental benign and is feasible for the preparation of NiO:Al and other Al-doped oxide thin film. - Graphical abstract: The ratio of Ni{sup 3+}/Ni{sup 2+} varies with Al content which can lead to different electrochemical performances. Among the as-prepared films, NiO film prepared from Ni-Al (19:1) LDH show the best electrochromic performance with a high transparency of 96%, large optical modulation range, fast switching speed and excellent durability. Display Omitted.

Electrochromic mirror using viologen-anchored nanoparticles

Energy Technology Data Exchange (ETDEWEB)

Kim, Han Na [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of); Cho, Seong M.; Ah, Chil Seong; Song, Juhee; Ryu, Hojun; Kim, Yong Hae [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); Kim, Tae-Youb, E-mail: youby@etri.re.kr [Electronics and Telecommunications Research Institute, Nature-mimic I/O interface Research Section, 218 Gajeong-roYuseong-gu, Daejeon 305-700 (Korea, Republic of); University of Science and Technology, Advanced Device Technology, 217 Gajeong-roYuseong-gu, Daejeon 305-350 (Korea, Republic of)

2016-10-15

Highlights: • Three types of ECM device were fabricated using viologen-anchored ECDs. • The devices were investigated according to their optical structures. • The anti-reflection material affects the reflectance and the coloration efficiency. • The device design of ECMs is a crucial factor for clear reflected images. - Abstract: Electrochromic mirrors (ECMs) that are used in automobile mirrors need to have high reflectance, a high contrast ratio, and a clear image. In particular, it is critical that distortions of clear images are minimized for safety. Therefore, an ECM is fabricated using viologen-anchored nanoparticles and a magnesium fluoride (MgF{sub 2}) layer with an anti-reflection function. The ECM has approximately 30.42% in the reflectance dynamic range and 125 cm{sup 2}/C high coloration efficiency.

Electrochromic effects in relation to energy transduction and energy coupling in chloroplast membranes

NARCIS (Netherlands)

Peters, R.L.A.

1986-01-01

A study was made on the kinetics of the flash-induced P515 electrochromic bandshift signal in spinach leaves and isolated chloroplasts. It was found that part of the signal (i.e. the slow component, also called reaction 2), normally present in dark-adapted membranes is absent from the signal under

Solid-state electrochromic cell with anodic iridium oxide film electrodes

International Nuclear Information System (INIS)

Dautremont-Smith, W.C.; Beni, G.; Schiavone, L.M.; Shay, J.L.

1979-01-01

A new solid-state electrochromic cell has been fabricated using an anodic iridium oxide film (AIROF) display electrode. The cell has the symmetric sandwich structure AIROFvertical-barNafionvertical-barAIROF, with the Nafion solid electrolyte opacified by an in situ precipitation technique. A symmetric square-wave voltage of 1.5 V amplitude produces clearly perceivable color changes from pale to dark blue-gray in approx. =1 sec when viewed in diffuse reflection. Good open-circuit optical memory is exhibited:

Electrochromic Radiator Coupon Level Testing and Full Scale Thermal Math Modeling for Use on Altair Lunar Lander

Science.gov (United States)

Bannon, Erika T.; Bower, Chad E.; Sheth, Rubik; Stephan, Ryan

2010-01-01

In order to control system and component temperatures, many spacecraft thermal control systems use a radiator coupled with a pumped fluid loop to reject waste heat from the vehicle. Since heat loads and radiation environments can vary considerably according to mission phase, the thermal control system must be able to vary the heat rejection. The ability to "turn down" the heat rejected from the thermal control system is critically important when designing the system. Electrochromic technology as a radiator coating is being investigated to vary the amount of heat rejected by a radiator. Coupon level tests were performed to test the feasibility of this technology. Furthermore, thermal math models were developed to better understand the turndown ratios required by full scale radiator architectures to handle the various operation scenarios encountered during a mission profile for the Altair Lunar Lander. This paper summarizes results from coupon level tests as well as the thermal math models developed to investigate how electrochromics can be used to increase turn down ratios for a radiator. Data from the various design concepts of radiators and their architectures are outlined. Recommendations are made on which electrochromic radiator concept should be carried further for future thermal vacuum testing.

Electrochromism in surface modified crystalline WO3 thin films grown by reactive DC magnetron sputtering

Science.gov (United States)

Karuppasamy, A.

2013-10-01

In the present work, tungsten oxide thin films were deposited at various oxygen chamber pressures (1.0-5.0 × 10-3 mbar) by maintaining the sputtering power density and argon pressure constant at 3.0 W/cm2 and 1.2 × 10-2 mbar, respectively. The role of surface morphology and porosity on the electrochromic properties of crystalline tungsten oxide thin films has been investigated. XRD and Raman studies reveal that all the samples post annealed at 450 ̊C in air for 3.0 h settle in monoclinic crystal system of tungsten oxide (W18O49). Though the phase of material is indifferent to oxygen pressure variations (PO2), morphology and film density shows a striking dependence on PO2. A systematic study on plasma (OES), morphology, optical and electrochromic properties of crystalline tungsten oxide reveal that the films deposited at PO2 of 2.0 × 10-3 mbar exhibit better coloration efficiency (58 cm2/C), electron/ion capacity (Qc: -25 mC/cm2), and reversibility (92%). This is attributed to the enhanced surface properties like high density of pores and fine particulates (100 nm) and to lesser bulk density of the film (ρ/ρo = 0.84) which facilitates the process of intercalation/de-intercalation of protons and electrons. These results show good promise toward stable and efficient crystalline tungsten oxide based electrochromic device applications.

Electrochromic properties of a novel low band gap conductive copolymer

Energy Technology Data Exchange (ETDEWEB)

Yigitsoy, Basak; Varis, Serhat; Tanyeli, Cihangir; Akhmedov, Idris M.; Toppare, Levent [Department of Chemistry, Middle East Technical University, 06531 Ankara (Turkey)

2007-07-10

A copolymer of 2,5-di(thiophen-2-yl)-1-p-tolyl-1H-pyrrole (DTTP) with 3,4-ethylene dioxythiophene (EDOT) was electrochemically synthesized. The resultant copolymer P(DTTP-co-EDOT) was characterized via cyclic voltammetry, FTIR, SEM, conductivity measurements and spectroelectrochemistry. Copolymer film has distinct electrochromic properties. It has four different colors (chestnut, khaki, camouflage green, and blue). At the neutral state {lambda}{sub max} due to the {pi}-{pi}{sup *} transition was found to be 487 nm and E{sub g} was calculated as 1.65 eV. Double potential step chronoamperometry experiment shows that copolymer film has good stability, fast switching time (less than 1 s) and good optical contrast (20%). An electrochromic device based on P(DTTP-co-EDOT) and poly(3,4-ethylenedioxythiophene) (PEDOT) was constructed and characterized. The device showed reddish brown color at -0.6 V when the P(DTTP-co-EDOT) layer was in its reduced state; whereas blue color at 2.0 V when PEDOT was in its reduced state and P(DTTP-co-EDOT) layer was in its oxidized state. At 0.2 V intermediate green state was observed. Maximum contrast (%{delta}T) and switching time of the device were measured as 18% and 1 s at 615 nm. ECD has good environmental and redox stability. (author)

Characterization of Porous WO3 Electrochromic Device by Electrochemical Impedance Spectroscopy

Directory of Open Access Journals (Sweden)

Chien Chon Chen

2013-01-01

Full Text Available This paper concerns the microstructure of the anodic tungsten oxide (WO3 and its use in an electrochromic (EC glass device. When voltages between 100 V and 160 V were applied to tungsten film for 1 h under 0.4 wt. % NaF electrolyte, porous WO3 film was formed. The film, which had a large surface area, was used as electrochromic film for EC glass. The average transmittance in a visible region of the spectrum for a 144 cm2 EC device was above 75% in the bleached state and below 40% in the colored state, respectively. Repeatability using of the colored/bleached cycles was tested good by a cyclic voltammograms method. The internal impedance values under colored and bleached states were detected and simulated using an electrical impedance spectra (EIS technique. The EC glass impedance characteristics were simulated using resistors, capacitors, and Warburg impedance. The ITO/WO3, WO3/electrolyte, electrolyte/NiO, and NiO/ITO interfaces can be simulated using a resistance capacitance (RC parallel circuits, and bulk materials such as the indium tin oxide (ITO and conducting wire can be simulated by using a series of resisters.

An economic analysis of the deposition of electrochromic WO3 via sputtering or plasma enhanced chemical vapor deposition

International Nuclear Information System (INIS)

Garg, D.; Henderson, P.B.; Hollingsworth, R.E.; Jensen, D.G.

2005-01-01

The costs of manufacturing electrochromic WO 3 thin films deposited by either radio frequency plasma enhanced chemical vapor deposition (PECVD) or DC reactive magnetron sputtering of metal targets were modeled. Both inline systems for large area glass substrates and roll-to-roll systems for flexible webs were compared. Costs of capital, depreciation, raw materials, labor, power, and other miscellaneous items were accounted for in the model. The results predict that on similar sized systems, PECVD can produce electrochromic WO 3 for as little as one-third the cost, and have more than 10 times the annual production capacity of sputtering. While PECVD cost is dominated by raw materials, primarily WF 6 , sputtering cost is dominated by labor and depreciation

Effects of Fluoro Substitution on the Electrochromic Performance of Alternating Benzotriazole and Benzothiadiazole-Based Donor–Acceptor Type Copolymers

Directory of Open Access Journals (Sweden)

Yan Zhang

2017-12-01

Full Text Available Two new donor–acceptor type electrochromic copolymers containing non-fluorinated and di-fluorinated benzothiadiazole analogues, namely P(TBT-TBTh and P(TBT-F-TBTh, were synthesized successfully through chemical polymerization. Both polymers were measured by cyclic voltammetry, UV-vis spectroscopy, colorimetry and thermogravimetric analysis to study the influence of fluoro substitution on the electrochromic performance. The results demonstrated that the two polymer films displayed well-defined redox peaks in pairs during the p-type doping, and showed distinct color change from dark gray blue to light green for P(TBT-TBTh with the band gap of 1.51 eV, and from gray blue to celandine green for P(TBT-F-TBTh with the band gap of 1.58 eV. P(TBT-F-TBTh presented lower highest occupied molecular orbital (HOMO and lowest unoccupied molecular orbital (LUMO energy levels, and better stability than P(TBT-TBTh. It was found that the two fluorine atoms participated in not only inductive effects but also mesomeric effects in the P(TBT-F-TBTh backbone. In addition, the polymers exhibited high optical contrasts, short response time, and favorable coloration efficiency, especially in the near infrared region. The characterization results indicated that the two reported polymers can be the potential choice as electrochromic materials.

Covalently Bonded Polyaniline and para-phenylenediamine Functionalized Graphene Oxide: How the Conductive Two-dimensional Nanostructure Influences the Electrochromic Behaviors of Polyaniline

International Nuclear Information System (INIS)

Xiong, Shanxin; Li, Zhufeng; Gong, Ming; Wang, Xiaoqin; Fu, Jialun; Shi, Yujing; Wu, Bohua; Chu, Jia

2014-01-01

Graphical abstract: - Abstract: Polyaniline (PANI) was attached onto the reduced graphene oxide (rGO) sheets through copolymerization of aniline with a para-phenylenediamine (PPD) functionalized graphene oxide (GO-PPD) using the poly(styrene sulfonate) (PSS) as the macromolecular dopant agent to produce a water-dispersible electrochromic material. The structures and the morphologies analysis confirm that the final electrochromic materials (rGO-PANI) are the mixture of PANI/PSS and the covalently bonded rGO-PANI (rGO-PANI hybrid). The rGO-PANI hybrid can be found to form a parallel arrangement to the substrate in the spin-coated film. This parallel arrangement of the layered two-dimensional nanostructure of rGO-PANI hybrid may narrow the ion transportation pathways of the exchanged ions, which will result in a high charge transfer resistance and slow switching speed. Meanwhile, with the conductive rGO added, the electrical conductivity of the electrochromic layer will be increased, which will benefit to low charge transfer resistance and high optical contrast. So the conductive two-dimensional nanostructure has a double-face influence on the electrochromic performances of PANI, which include a positive influence on the electrical conductivity and a negative influence on the ion diffusion. The overall influences depend on the loading amount of GO-PPD. With 4 wt.% GO-PPD feeding, the optical contrast was enhanced by 36% from 0.38 for PANI/PSS to 0.52 for rGO-PANI-3, while the coloration time was almost same as that of PANI/PSS and the bleaching time was decreased by ∼20% from 9.1s for PANI/PSS to 7.4s for rGO-PANI-3. The electrochemical tests showed that with the increasing of GO-PPD loading, the peak currents of cyclic voltammetry (CV) curves were increased, and the peak locations shifted to the positive potential for oxidation peak and the negative potential for reduction peak, respectively, which confirmed that the double-face influences of rGO-PANI on the

Conductive transition metal oxide nanostructured electrochromic material and optical switching devices constructed thereof

Science.gov (United States)

Mattox, Tracy M.; Koo, Bonil; Garcia, Guillermo; Milliron, Delia J.; Trizio, Luca De; Dahlman, Clayton

2017-10-10

An electrochromic device includes a nanostructured transition metal oxide bronze layer that includes one or more transition metal oxide and one or more dopant, a solid state electrolyte, and a counter electrode. The nanostructured transition metal oxide bronze selectively modulates transmittance of near-infrared (NIR) spectrum and visible spectrum radiation as a function of an applied voltage to the device.

Optical detection of ion diffusion in electrochromic poly(3,4-ethylenedioxy)thiophene film using microcantilever electrodes

DEFF Research Database (Denmark)

Lin, Rong; Stokbro, Kurt; Madsen, Dorte Nørgaard

2005-01-01

potential of the film induced dark (light-absorbing) rings, which spread out from the anode on a time scale of seconds. The rate of expansion of the rings as well as the final diameter depended on the bias voltage. Using two micro four-point probes simultaneously, we measured with one probe the conductance......We present measurements of microscale electrochromic switching of poly(3,4-ethylenedioxy)thiophene doped with poly(4-styrene sulfonate), thin film using microfabricated multi-point probe electrodes. After treatment with a dilute hydrochloric acid, a voltage bias above 3 V with respect to the ground...... of the film outside, near and inside a dark ring induced by a voltage applied to another probe and found the resistivity to be directly related to the observed absorbance of the film. The standard electrochromic mechanism of ion insertion was used to explain the observations. We anticipate this experimental...

A transparent electrochromic metal-insulator switching device with three-terminal transistor geometry

Science.gov (United States)

Katase, Takayoshi; Onozato, Takaki; Hirono, Misako; Mizuno, Taku; Ohta, Hiromichi

2016-05-01

Proton and hydroxyl ion play an essential role for tuning functionality of oxides because their electronic state can be controlled by modifying oxygen off-stoichiometry and/or protonation. Tungsten trioxide (WO3), a well-known electrochromic (EC) material for smart window, is a wide bandgap insulator, whereas it becomes a metallic conductor HxWO3 by protonation. Although one can utilize electrochromism together with metal-insulator (MI) switching for one device, such EC-MI switching cannot be utilized in current EC devices because of their two-terminal structure with parallel-plate configuration. Here we demonstrate a transparent EC-MI switchable device with three-terminal TFT-type structure using amorphous (a-) WO3 channel layer, which was fabricated on glass substrate at room temperature. We used water-infiltrated nano-porous glass, CAN (calcium aluminate with nano-pores), as a liquid-leakage-free solid gate insulator. At virgin state, the device was fully transparent in the visible-light region. For positive gate voltage, the active channel became dark blue, and electrical resistivity of the a-WO3 layer drastically decreased with protonation. For negative gate voltage, deprotonation occurred and the active channel returned to transparent insulator. Good cycleability of the present transparent EC-MI switching device would have potential for the development of advanced smart windows.

A wide-gap a-SiC:H PV-powered electrochromic window coating

Energy Technology Data Exchange (ETDEWEB)

Gao, W.; Lee, S.H.; Xu, Y.; Benson, D.K.; Deb, S.K.; Branz, H.M. [National Renewable Energy Lab., Golden, CO (United States)

1998-09-01

The authors report on the first monolithic, amorphous-silicon-based, photovoltaic-powered electrochromic window coating. The coating employs a wide bandgap a-Si{sub 1{minus}x}C{sub x}:H n-i-p photovoltaic (PV) cell as a semitransparent power supply, and a Li{sub y}WO{sub 3}/LiAlF{sub 4}/V{sub 2}O{sub 5} electrochromic (EC) device as an optical-transmittance modulator. The EC device is deposited directly on top of a PV cell that coats a glass substrate. The a-Si{sub 1{minus}x}C{sub x}:H PV cell has a Tauc gap of 2.2 eV and a transmittance of 60--80% over a large portion of the visible light spectrum. The authors reduced the thickness of the device to about 600 {angstrom} while maintaining a 1-sun open-circuit voltage of 0.9 V and short-circuit current of 2 mA/cm{sup 2}. The prototype 16 cm{sup 2} PV/EC device modulates the transmittance by more than 60% over a large portion of the visible spectrum. The coloring and bleaching times of the EC device are approximately 1 minute under normal operating conditions ({+-} 1 volt). A brief description of photoelectrochromic windows study is also given.

In situ infrared spectroscopic study of the electrochromic reactions of tungsten trioxide films

International Nuclear Information System (INIS)

Habib, M.A.; Maheswari, S.P.

1991-01-01

This paper reports on thin WO 3 films which are transparent in the oxidized state and colored in the reduced state. These changes in optical properties are associated with compositional variations of the material. Changes in vibrational intensities of W double-bond O, W emdash O, and W double-bond O emdash H bonds in the electrochromic WO 3 film were detected by an in situ FTIR technique at various stages of reduction (coloration). The absorbance due to O emdash H stretching and bending vibrations was found to increase during the electrochemical reduction of the film, indicating the incorporation of water into the film along with the formation of H x WO 3 bronze during coloration. The absorbance due to W double-bond O vibration decreased while that due to W emdash O vibration increased during reduction. These observations suggest that during the coloration process W double-bond O bonds break and new W emdash O bonds form in the film, and thus, provide direct evidence for the electrochromic reaction. O 2 W double-bond O + xH + + xe - ↔ O 2 W emdash O emdash H x

Investigation of mechanical bending instability in flexible low-temperature-processed electrochromic display devices

Energy Technology Data Exchange (ETDEWEB)

Cheng, Chin-Pao; Chou, Chuan-Pu; Hsu, Che-Hsiang; Teng, Tun-Chien; Cheng, Chun-Hu, E-mail: chcheng@ntnu.edu.tw; Syu, Yu-Yang

2015-06-01

In this study, polyethylene naphthalate (PEN) was investigated as a flexible substrate because, compared with polyethylene terephthalate, it achieves a lower root mean square roughness and transmittance, which is favorable for reducing leakage from the bottom of flexible substrates. A flexible device structure composed of tungsten oxide/indium-doped tin oxide/PEN was used in an electrochromic (EC) test. The experimental results show that the flexible EC display device achieved a high transmittance difference of > 40% and color efficiency of 70.2 cm{sup 2}/C at 560 nm. The transmittance difference was degraded in the visible range after 200 cycles of continuous bending. Furthermore, compared with flat fresh devices, the WO{sub 3} device exhibited poor retention properties in a colored state after being subjected to longer bending cycles. - Highlights: • Flexible electrochromic device with endurance bending was demonstrated. • Interface defects or vacancies near the flexible substrate affect the self-bleaching behavior. • High color efficiency of 117.2 cm{sup 2}/coul at 700 nm wavelength is reached. • Interface defect centers lower the redox energy barrier which reduces the bleaching time.

Optical, structural and electrochromic behavior studies on nanocomposite thin film of aniline, o-toluidine and WO3

Science.gov (United States)

Najafi-Ashtiani, Hamed; Bahari, Ali

2016-08-01

In the field of materials for electrochromic (EC) applications much attention was paid to the derivatives of aniline. We report on the optical, structural and electrochromic properties of electrochromic thin film based on composite of WO3 nanoparticles and copolymer of aniline and o-toluidine prepared by electrochemical polymerization method on fluorine doped tin oxide (FTO) coated glass. The thin film was studied by X-ray diffraction (XRD) and Fourier transforms infrared (FTIR) spectroscopy. The morphology of prepared thin film was characterized by field emission scanning electron microscopy (FESEM), atomic force microscopy (AFM) and the thermal gravimetric analysis (TGA) as well. The optical spectra of nanocomposite thin film were characterized in the 200-900 nm wavelength range and EC properties of nanocomposite thin film were studied by cyclic voltammetry (CV). The calculation of optical band gaps of thin film exhibited that the thin film has directly allowed transition with the values of 2.63 eV on first region and 3.80 eV on second region. Dispersion parameters were calculated based on the single oscillator model. Finally, important parameters such as dispersion energy, oscillator energy and lattice dielectric constant were determined and compared with the data from other researchers. The nonlinear optical properties such as nonlinear optical susceptibility, nonlinear absorption coefficient and nonlinear refractive index were extracted. The obtained results of nanocomposite thin film can be useful for the optoelectronic applications.

Cyclic voltammetry on sputter-deposited films of electrochromic Ni oxide: Power-law decay of the charge density exchange

Energy Technology Data Exchange (ETDEWEB)

Wen, Rui-Tao, E-mail: Ruitao.Wen@angstrom.uu.se; Granqvist, Claes G.; Niklasson, Gunnar A. [Department of Engineering Sciences, The A°ngström Laboratory, Uppsala University, P. O. Box 534, SE-75121 Uppsala (Sweden)

2014-10-20

Ni-oxide-based thin films were produced by reactive direct-current magnetron sputtering and were characterized by X-ray diffraction and Rutherford backscattering spectroscopy. Intercalation of Li{sup +} ions was accomplished by cyclic voltammetry (CV) in an electrolyte of LiClO{sub 4} in propylene carbonate, and electrochromism was documented by spectrophotometry. The charge density exchange, and hence the optical modulation span, decayed gradually upon repeated cycling. This phenomenon was accurately described by an empirical power law, which was valid for at least 10{sup 4} cycles when the applied voltage was limited to 4.1 V vs Li/Li{sup +}. Our results allow lifetime assessments for one of the essential components in an electrochromic device such as a “smart window” for energy-efficient buildings.

The effects of heat treatment on optical, structural, electrochromic and bonding properties of Nb{sub 2}O{sub 5} thin films

Energy Technology Data Exchange (ETDEWEB)

Coşkun, Özlem Duyar, E-mail: duyar@hacettepe.edu.tr [Hacettepe University, Department of Physics Engineering, Thin Film Preparation and Characterization Laboratory, Ankara (Turkey); Demirel, Selen, E-mail: nymph24@gmail.com [Hacettepe University, Department of Physics Engineering, Thin Film Preparation and Characterization Laboratory, Ankara (Turkey); Hacettepe University, Nanotechnology and Nanomedicine Department, Ankara (Turkey); Atak, Gamze, E-mail: gbaser@hacettepe.edu.tr [Hacettepe University, Department of Physics Engineering, Thin Film Preparation and Characterization Laboratory, Ankara (Turkey)

2015-11-05

Nb{sub 2}O{sub 5} thin films were deposited onto heated glass substrates by RF magnetron sputtering using a Nb{sub 2}O{sub 5} target. The films were annealed in air at temperatures between 400 and 700 °C for 6 h. Effects of the crystalline structure on optical, structural, electrochromic and bonding properties of the Nb{sub 2}O{sub 5} thin films were investigated by X-ray diffraction, atomic force microscopy, X-ray photoelectron spectroscopy, optical spectrophotometry and electrochemical measurements. The film refractive index varied between 2.09 and 2.22 at the wavelength of 550 nm depending on the annealing temperature. The decrease of the optical band gap revealed for the films with increasing annealing temperature is attributed to oxygen-ion vacancies in the film structure. The orthorhombic structure of Nb{sub 2}O{sub 5} films resulted in good electrochromic properties with high colouration efficiencies of 19.56 cm{sup 2}/C and 53.24 cm{sup 2}/C at 550 nm and 1000 nm, respectively. The optical, structural and electrochromic properties of the different crystalline polymorphic forms of the Nb{sub 2}O{sub 5} films make them attractive for optical applications. - Highlights: • Stoichiometric Nb{sub 2}O{sub 5} films prepared using RF magnetron sputtering technique. • The different crystalline forms of Nb{sub 2}O{sub 5} thin films obtained by annealing. • The optical, structural and electrochromic properties of the films were investigated. • The optical band gap decreased with increasing annealing temperature. • The orthorhombic T-Nb{sub 2}O{sub 5} films exhibited a higher colouration efficiency.

An economic analysis of the deposition of electrochromic WO{sub 3} via sputtering or plasma enhanced chemical vapor deposition

Energy Technology Data Exchange (ETDEWEB)

Garg, D. [Air Products and Chemicals Inc., 7201 Hamilton Blvd., Allentown, PA 18195-7201 (United States); Henderson, P.B. [Air Products and Chemicals Inc., 7201 Hamilton Blvd., Allentown, PA 18195-7201 (United States)]. E-mail: henderpb@airproducts.co; Hollingsworth, R.E. [ITN Energy Systems Inc., 8130 Shaffer Pkwy, Littleton, CO 80127 (United States); Jensen, D.G. [ITN Energy Systems Inc., 8130 Shaffer Pkwy, Littleton, CO 80127 (United States)

2005-06-15

The costs of manufacturing electrochromic WO{sub 3} thin films deposited by either radio frequency plasma enhanced chemical vapor deposition (PECVD) or DC reactive magnetron sputtering of metal targets were modeled. Both inline systems for large area glass substrates and roll-to-roll systems for flexible webs were compared. Costs of capital, depreciation, raw materials, labor, power, and other miscellaneous items were accounted for in the model. The results predict that on similar sized systems, PECVD can produce electrochromic WO{sub 3} for as little as one-third the cost, and have more than 10 times the annual production capacity of sputtering. While PECVD cost is dominated by raw materials, primarily WF{sub 6}, sputtering cost is dominated by labor and depreciation.

Environmental assessment of electrochromic glazing production

International Nuclear Information System (INIS)

Syrrakou, E.; Papaefthimiou, S.; Yianoulis, P.

2005-01-01

The life cycle analysis method was used to determine the environmental impacts associated with the production of an electrochromic (EC) glazing (called ECD). This paper describes the inventory analysis for all the basic materials used during the manufacture of the ECD, i.e. K-Glass, tungsten oxide (WO 3 ), poly-methyl methacrylate (PMMA), propylene carbonate (PC), lithium perchlorate (LiClO 4 ) and acetic silicone sealant. K-Glass, PC and PMMA account for the 98% of the total device mass and the CO 2 emissions during their production processes are 810 g. The total embodied energy was estimated to be 49 MJ/ECD, with 32.1 MJ/unit of them derived from the K-Glass. The comparison of the total embodied energies of the ECD and various insulating glass units concluded that mass-produced EC glazings could easily compete with them in terms of environmental performance, anticipating cost attenuation and overall thermal and optical behavior. The above analysis could be implemented for the reduction of the embodied energy of the ECD life cycle, since it is proposed as an energy saving device. (Author)

Electrochromics for smart windows: Oxide-based thin films and devices

Energy Technology Data Exchange (ETDEWEB)

Granqvist, Claes G.

2014-08-01

Electrochromic (EC) smart windows are able to vary their throughput of visible light and solar energy by the application of an electrical voltage and are able to provide energy efficiency and indoor comfort in buildings. Section 1 explains why this technology is important and timely by first outlining today's precarious situation concerning increasing energy use and associated effects on the world's climate, and this section also underscores the great importance of enhancing the energy efficiency of buildings by letting them function more in harmony with the environment—particularly its varying temperature—than is possible with current mainstream technologies. This same chapter also surveys recent work on the energy savings and other benefits that are possible with EC-based technologies. Section 2 then provides some notes on the history of the EC effect and its applications. Section 3 presents a generic design for the oxide-based EC devices that are most in focus for present-day applications and research. This design includes five superimposed layers with a centrally-positioned electrolyte connecting two oxide films—at least one of which having EC properties—and with transparent electrical conductors surrounding the three-layer structure in the middle. It is emphasized that this construction can be viewed as a thin-film electrical battery whose charging state is manifested as optical absorption. Also discussed are six well known hurdles for the implementation of these EC devices, as well as a number of practical constructions of EC-based smart windows. Section 4 is an in-depth discussion of various aspects of EC oxides. It begins with a literature survey for 2007–2013, which updates earlier reviews, and is followed by a general discussion of optical and electronic effects and, specifically, on charge transfer absorption in tungsten oxide. Ionic effects are then treated with foci on the inherent nanoporosity of the important EC oxides and on the

Electrochromics for smart windows: Oxide-based thin films and devices

International Nuclear Information System (INIS)

Granqvist, Claes G.

2014-01-01

Electrochromic (EC) smart windows are able to vary their throughput of visible light and solar energy by the application of an electrical voltage and are able to provide energy efficiency and indoor comfort in buildings. Section 1 explains why this technology is important and timely by first outlining today's precarious situation concerning increasing energy use and associated effects on the world's climate, and this section also underscores the great importance of enhancing the energy efficiency of buildings by letting them function more in harmony with the environment—particularly its varying temperature—than is possible with current mainstream technologies. This same chapter also surveys recent work on the energy savings and other benefits that are possible with EC-based technologies. Section 2 then provides some notes on the history of the EC effect and its applications. Section 3 presents a generic design for the oxide-based EC devices that are most in focus for present-day applications and research. This design includes five superimposed layers with a centrally-positioned electrolyte connecting two oxide films—at least one of which having EC properties—and with transparent electrical conductors surrounding the three-layer structure in the middle. It is emphasized that this construction can be viewed as a thin-film electrical battery whose charging state is manifested as optical absorption. Also discussed are six well known hurdles for the implementation of these EC devices, as well as a number of practical constructions of EC-based smart windows. Section 4 is an in-depth discussion of various aspects of EC oxides. It begins with a literature survey for 2007–2013, which updates earlier reviews, and is followed by a general discussion of optical and electronic effects and, specifically, on charge transfer absorption in tungsten oxide. Ionic effects are then treated with foci on the inherent nanoporosity of the important EC oxides and on the

Electrochromism of the electroless deposited cuprous oxide films

International Nuclear Information System (INIS)

Neskovska, R.; Ristova, M.; Velevska, J.; Ristov, M.

2007-01-01

Thin cuprous oxide films were prepared by a low cost, chemical deposition (electroless) method onto glass substrates pre-coated with fluorine doped tin oxide. The X-ray diffraction pattern confirmed the Cu 2 O composition of the films. Visible transmittance spectra of the cuprous oxide films were studied for the as-prepared, colored and bleached films. The cyclic voltammetry study showed that those films exhibited cathode coloring electrochromism, i.e. the films showed change of color from yellowish to black upon application of an electric field. The transmittance across the films for laser light of 670 nm was found to change due to the voltage change for about 50%. The coloration memory of those films was also studied during 6 h, ex-situ. The coloration efficiency at 670 nm was calculated to be 37 cm 2 /C

Optical and electrochromic properties of sol-gel deposited Ti- doped vanadium oxide films

International Nuclear Information System (INIS)

Oezer, N.; Sabuncu, S.

1997-01-01

Because of the yellowish color, vanadium oxide films in the as deposited state is not as favorable as transparent coatings for most elector chromic devices. an interesting possibility to alter the yellowish colours is the doping with other non-absorbing metal oxides. Ti doped vanadium oxide films with various amounts of titanium were synthesized and investigated as transparent counter electrodes for electrochromic transmissive device application. Electrochromic titanium doped vanadium pentoxide (V sub 2 O 5) coatings were prepared by the sol-gel dip coating technique. The coating solutions were synthesized from vanadium tri(isopropoxide) precursors. X-ray diffraction (XRD) studies showed that the sol-gel deposited doped films heat treated at temperatures below 350 degree centigrade, were amorphous, whereas hose heat treated at higher temperatures were slight y crystalline. The optical and electrochemical properties of the Ti doped vanadium oxide films has been investigated in 0.1 m LiClO sub 4 propylene carbonate solution color changes by dropping were noted for all investigated films exhibits good electrochemical cycling (CV) measurements also showed that Ti doped V sub 2 O sub 5 films exhibits good electrochemical cycling reversibility, 'in situ' optical measurement revealed that those films exhibits good electrochemical cycling the spectra range 300 < lambda < 800 nm and change color between yellow and light green. The change in visible transmittance was 25 % for 5% Ti doped film. (author)

Self-Stacked Reduced Graphene Oxide Nanosheets Coated with Cobalt-Nickel Hydroxide by One-Step Electrochemical Deposition toward Flexible Electrochromic Supercapacitors.

Science.gov (United States)

Grote, Fabian; Yu, Zi-You; Wang, Jin-Long; Yu, Shu-Hong; Lei, Yong

2015-09-01

The implementation of an optical function into supercapacitors is an innovative approach to make energy storage devices smarter and to meet the requirements of smart electronics. Here, it is reported for the first time that nickel-cobalt hydroxide on reduced graphene oxide can be utilized for flexible electrochromic supercapacitors. A new and straightforward one-step electrochemical deposition process is introduced that is capable of simultaneously reducing GO and depositing amorphous Co(1-x)Ni(x)(OH)2 on the rGO. It is shown that the rGO nanosheets are homogeneously coated with metal hydroxide and are vertically stacked. No high temperature processes are used so that flexible polymer-based substrates can be coated. The synthesized self-stacked rGO-Co(1-x)Ni(x)(OH)2 nanosheet material exhibits pseudocapacitive charge storage behavior with excellent rate capability, high Columbic efficiency, and nondiffusion limited behavior. It is shown that the electrochemical behavior of the Ni(OH)2 can be modulated, by simultaneously depositing nickel and cobalt hydroxide, into broad oxidization and reduction bands. Further, the material exhibits electrochromic property and can switch between a bleached and transparent state. Literature comparison reveals that the performance characteristics of the rGO-Co(1-x)Ni(x)(OH)2 nanosheet material, in terms of gravimetric capacitance, areal capacitance, and long-term cycling stability, are among the highest reported values of supercapacitors with electrochromic property. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Novel poly(triphenylamine-alt-fluorene) with asymmetric hexaphenylbenzene and pyrene moieties: synthesis, fluorescence, flexible near-infrared electrochromic devices and theoretical investigation

KAUST Repository

Wang, Po-I.

2016-01-13

© The Royal Society of Chemistry 2016. In this study, a new triphenylamine-alt-fluorene conjugated copolymer, HPBPYFL6, with hexaphenylbenzene (HPB) and pyrene as asymmetrical pendant groups was synthesized via Suzuki coupling polymerization. The conjugated polymer had a weight-average molecular weight of 5.8 × 104 g mol-1 with a polydispersity index of 2.5 characterized by gel permeation chromatography (GPC). HPBPYFL6 showed good solubility in common organic solvents such as NMP, THF, toluene and dichloromethane at 25°C. In addition, HPBPYFL6 possessed a high glass transition temperature of 260°C and a 10% weight-loss temperature of 503°C in nitrogen. HPBPYFL6 bearing a pyrene moiety had a solvatochromic fluorescence shift from a green to an orange emission as the polarity of the solvent increased. Cyclic voltammetry of HPBPYFL6 films cast onto indium-tin oxide-coated glass (ITO-glass) exhibited two oxidation redox couples at an E1/2 value of 0.82 and 1.17 V versus Ag/Ag+ in an acetonitrile solution. The HPBPYFL6 film on graphene-coated PET had an E1/2 value of 0.24 and 1.12 V. Conjugated polymer films exhibited reversible electrochromic behaviour with a colour change from pale yellow to deep blue upon electrochemical oxidation and high absorbance in the near-infrared (NIR) region. The switching and bleaching times were 5.16 s and 3.12 s for 1231 nm and were 3.30 s and 3.74 s for 1030 nm of HPBPYFL6 on ITO-glass. The strong NIR electrochromic absorbance of HPBPYFL6 was attributed to intervalence charge transfer by the incorporation of the HPB moiety. This phenomenon was confirmed by chemical oxidation as the oxidant contents increased in the solution state. Furthermore, the electrochromic mechanism was interpreted by DFT calculation and the simulated NIR electrochromic spectra of model compound HPBPYFL are in good agreement with the experimental data.

An investigation of the insertion of the cations H{sup +}, Na{sup +}, K{sup +} on the electrochromic properties of the thermally evaporated WO{sub 3} thin films grown at different substrate temperatures

Energy Technology Data Exchange (ETDEWEB)

Patel, K.J. [Applied Physics Department, Faculty of Technology and Engineering, M.S. University of Baroda, Kalabhavan, Vadodara 390001, Gujarat (India); Panchal, C.J., E-mail: cjpanchal_msu@yahoo.com [Applied Physics Department, Faculty of Technology and Engineering, M.S. University of Baroda, Kalabhavan, Vadodara 390001, Gujarat (India); Desai, M.S. [Applied Physics Department, Faculty of Technology and Engineering, M.S. University of Baroda, Kalabhavan, Vadodara 390001, Gujarat (India); Mehta, P.K. [Physics Department, Faculty of Science, M.S. University of Baroda, Vadodara 390002, Gujarat (India)

2010-11-01

The phenomenon of electrochromism in tungsten trioxide (WO{sub 3}) thin films has recently attained considerable interest due to their enormous applications in inorganic thin film electrochromic devices. We have investigated the compositional, optical, and electrochromic properties of the WO{sub 3} thin films grown at different substrate temperatures by the thermal evaporation of WO{sub 3} powder. The thin films were characterized using X-ray diffraction (XRD), X-ray photo-emission spectroscopy (XPS), and electrochemical techniques. The XPS analysis suggested that the oxygen to tungsten (O/W) ratio decreases, i.e., the oxygen deficiency increases, on increasing the substrate temperature up to 500 deg. C. The electrochemical analysis provided a comparative study of the coloration efficiency (CE) of the WO{sub 3} thin films intercalated with three different ions viz. H{sup +}, Na{sup +}, and K{sup +}. The effect of the variation of the substrate temperature on the CE and the switching time have also been investigated for the WO{sub 3} thin films intercalated with H{sup +} ions; the thin films deposited at RT and intercalated with H{sup +} ions are found to possess adequate electrochromic properties viz. CE and switching time from device point of view.

Hybrid Optical Devices: The Case of the Unification of the Electrochromic Device and the Organic Solar Cell

Directory of Open Access Journals (Sweden)

Andre F. S. Guedes

2016-06-01

Full Text Available The development of Hybrid Optical Devices, using some flexible optically transparent substrate material and organic semiconductor materials, has been widely utilized by the organic electronic industry, when manufacturing new technological products. The Hybrid Optical Device is constituted by the union of the electrochromic device and the organic solar cell. The flexible organic photovoltaic solar cells, in this hybrid optical device, have been the Poly base (3-hexyl thiophene, P3HT, Phenyl-C61-butyric acid methyl ester, PCBM and Polyaniline, PANI, all being deposited in Indium Tin Oxide, ITO. In addition, the thin film, obtained by the deposition of PANI, and prepared in perchloric acid solution, has been identified through PANI-X1. In the flexible electrochromic device, the Poly base (3,4-ethylenedioxythiophene, PEDOT, has been prepared in Propylene Carbonate, PC, being deposited in Indium Tin Oxide, ITO. Also, both devices have been united by an electrolyte solution prepared with Vanadium Pentoxide, V2O5, Lithium Perchlorate, LiClO4, and Polymethylmethacrylate, PMMA. This device has been characterized through Electrical Measurements, such as UV-Vis Spectroscopy and Scanning Electron Microscopy (SEM. Thus, the result obtained through electrical measurements has demonstrated that the flexible organic photovoltaic solar cell presented the characteristic curve of standard solar cell after spin-coating and electrodeposition. Accordingly, the results obtained with optical and electrical characterization have revealed that the electrochromic device demonstrated some change in optical absorption, when subjected to some voltage difference. Moreover, the inclusion of the V2O5/PANI-X1 layer reduced the effects of degradation that this hybrid organic device caused, that is, solar irradiation. Studies on Scanning Electron Microscopy (SEM have found out that the surface of V2O5/PANI-X1 layers can be strongly conditioned by the surface morphology of the

High-performance electrochromic device based on nanocellulose/polyaniline and nanocellulose/poly(3,4-ethylenedioxythiophene) composite thin films

Science.gov (United States)

Zhang, Sihang; Fu, Runfang; Du, Zoufei; Jiang, Mengjin; Zhou, Mi; Gu, Yingchun; Chen, Sheng

2017-07-01

With the development of nanotechnology, nanocomposite materials based on renewable resources are the focus of this research. Nanocellulose was prepared using sulfuric acid to swell cotton pulp, following with extensive ultrasonication. Nanocellulose/polyaniline (NC/PANI) and nanocellulose/poly(3,4-ethylenedioxythiophene) (NC/PEDOT) nanocomposites with core/shell structure were manufactured by in situ polymerization. The film-forming properties and electrochromic properties of PANI and PEDOT were significantly improved using the nanocellulose as matrix. NC/PANI and NC/PEDOT composite films were studied in single and dual electrochromic devices (ECDs). A viscous gel electrolyte (GE) was used in ECDs. The architectural design of single and dual device was ITO/NC-PANI/GE/ITO or ITO/NC-PEDOT/GE/ITO and ITO/NC-PANI/GE/NC-PEDOT/ITO, respectively. The dual ECD based on NC/PANI and NC/PEDOT composite films exhibited a higher color contrast (30.3%), shortest response time (1.5 s for bleaching and 1.9 s for coloring), largest coloration efficiency (241.6 C/cm2), and best cycling stability (over 150 cycles) compared with the single devices.

The improvement of all-solid-state electrochromic devices fabricated with the reactive sputter and cathodic arc technology

Directory of Open Access Journals (Sweden)

Min-Chuan Wang

2016-11-01

Full Text Available The all-solid-state electrochromic device (ECD with the one substrate structure fabricated by the reactive dc magnetron sputtering (DCMS and cathodic vacuum arc plasma (CVAP technology has been developed for smart electrochromic (EC glass application. The EC layer and ion conductor layer were deposited by reactive DCMS and CVAP technology, respectively. The ion conductor layer Ta2O5 deposited by the CVAP technology has provided the better porous material structure for ion transportation and showed 1.76 times ion conductivity than devices with all sputtering process. At the same time, the EC layer WO3 and NiO deposited by the reactive DCMS have also provided the high quality and uniform characteristic to overcome the surface roughness effect of the CVAP ion conductor layer in multilayer device structure. The all-solid-state ECD with the CVAP ion conductor layer has demonstrated a maximum transmittance variation (ΔT of 55% at 550nm and a faster-switching speed. Furthermore, the lower equipment cost and higher deposition rate could be achieved by the application of CVAP technology.

FORMATION AND ELECTROCHEMICAL BEHAVIOUR OF POLYION COMPLEXES FOR ELECTROCHROMIC DISPLAY MATERIAL

Institute of Scientific and Technical Information of China (English)

WAN Guoxiang; WANG Bing; DENG Zhenghua; LUO Chunqiao

1988-01-01

Formation of intermacromolecular complexes containing viologen and electron-transfer reaction occurred on the electrode modified by the complex films were studied. Compositions and morphology of the complexes depend on the properties of polyanion and chemical environment of complexation. The analytical results of cyclic voltammetry (CV) and rotating disk voltammetry(RDV) indicated: (1) active sites of viologen in network of complexes transferred single electron reversibly; (2) the redox peak currents showed excellent symmetry and stability; (3) redox potentials were related to properties of polyanions, varying from -0.4 to -0.6V (vs. SCE). Electrochromic materials with different displaying colors could be obtained by changing the structure of polyviologen.

Annealing induced structural evolution and electrochromic properties of nanostructured tungsten oxide films

Energy Technology Data Exchange (ETDEWEB)

Wu, Ching-Lin [Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan, ROC (China); Lin, Chung-Kwei [School of Dental Technology, Taipei Medical University, Taipei City 110, Taiwan, ROC (China); Wang, Chun-Kai [Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan, ROC (China); Wang, Sheng-Chang [Department of Mechanical Engineering, Southern Taiwan University, Tainan 710, Taiwan, ROC (China); Huang, Jow-Lay, E-mail: JLH888@mail.ncku.edu.tw [Department of Materials Science and Engineering, National Cheng Kung University, Tainan 701, Taiwan, ROC (China); Department of Chemical and Materials Engineering, National University of Kaohsiung, Kaohsiung 81148, Taiwan, ROC (China); Research Center for Energy Technology and Strategy, National Cheng Kung University, Tainan 701, Taiwan, ROC (China)

2013-12-31

The effect of microstructure on the optical and electrochemical properties of nanostructured tungsten oxide films was evaluated as a function of annealing temperature. The films using block copolymer as the template were prepared from peroxotungstic acid (PTA) by spin-coating onto the substrate and post-annealed at 250–400 °C to form tungsten oxide films with nanostructure. The microstructure of the films was measured by X-ray diffraction and surface electron microscopy. The films annealed at temperatures below 300 °C are characterized by amorphous or nanocrystalline structures with a pore size of less than 10 nm. The evaluated annealing temperature caused a triclinic crystalline structure and microcracks. Cyclic voltammetry measurements were performed in a LiClO{sub 4}-propylene carbonate electrolyte. The results showed that the ion inserted capacity were maximized for films annealed at 300 °C and decreased with the increasing of annealing temperature. The electrochromic properties of the nanostructured tungsten oxide films were evaluated simultaneously by potentiostat and UV–vis spectroscopy. The films annealed at 300 °C exhibit high transmission modulation (∆T ∼ 40%) at λ = 633 nm and good kinetic properties. As a result, the correlation between the microstructure and kinetic properties was established, and the electrochromic properties have been demonstrated. - Highlights: • Surfactant-assisted WO{sub 3} films have been prepared by sol–gel method. • Nanostructure of porous WO{sub 3} film is retained after crystallization. • Kinetic properties of WO{sub 3} can be improved by nanostructure and crystallinity.

Low-cost fabrication of WO{sub 3} films using a room temperature and low-vacuum air-spray based deposition system for inorganic electrochromic device applications

Energy Technology Data Exchange (ETDEWEB)

Park, Sung-Ik [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Kim, Sooyeun, E-mail: sooyeunk@u.washington.edu [Department of Mechanical Engineering, University of Washington, Seattle, WA (United States); Choi, Jung-Oh; Song, Ji-Hyeon [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Taya, Minoru [Department of Mechanical Engineering, University of Washington, Seattle, WA (United States); Ahn, Sung-Hoon, E-mail: ahnsh@snu.ac.kr [Department of Mechanical and Aerospace Engineering, Seoul National University, Seoul (Korea, Republic of); Institute of Advanced Machines and Design, Seoul (Korea, Republic of)

2015-08-31

We report the deposition of tungsten oxide (WO{sub 3}) thin films on fluorine-doped tin oxide (FTO) and indium-doped tin oxide (ITO) glass substrates by using a room-temperature deposition system based on low-vacuum air-spray for the fabrication of inorganic electrochromic windows. The structure of the WO{sub 3} films was characterized using X-ray diffraction, and the surface morphology and film thickness were investigated using scanning electron microscopy and atomic force microscopy. The color of the prepared WO{sub 3} films changed from slight yellow to dark blue under applied voltages, demonstrating electrochromism. The WO{sub 3} film coated FTO glass exhibited a large electrochromic contrast of up to 50% at a wavelength of 800 nm. The electrochemical properties of the films were examined using cyclic voltammetry and chronocoulometry. - Highlights: • WO{sub 3} thin films were fabricated using an air-spray based deposition system at room temperature under low-vacuum conditions. • Dry WO{sub 3} particles were directly deposited on FTO and ITO glasses by using a low-cost deposition system. • The FTO glass based WO{sub 3} film showed the optical contrast of 50% at a wavelength of 800 nm.

Electrochromic coatings made of surface modified rutile and anatase pigments: Influence of trisilanol POSS dispersant on electrochromic effect

Energy Technology Data Exchange (ETDEWEB)

Mihelčič, Mohor [National Institute of Chemistry, Hajdrihova 19, 1000 Ljubljana (Slovenia); Francetič, Vojmir [Faculty of Chemistry and Chemical Technology, University of Ljubljani, Aškerčeva cesta 5, 1000 Ljubljana (Slovenia); Pori, Pavli [Chemcolor Sevnica d.o.o., Dolenje Brezovo 35, 8290 Sevnica (Slovenia); Gradišar, Helena [National Institute of Chemistry, Hajdrihova 19, 1000 Ljubljana (Slovenia); Kovač, Janez [Jožef Stefan Institute., Jamova 39, SI-1000 Ljubljana (Slovenia); Orel, Boris, E-mail: boris.orel@ki.si [National Institute of Chemistry, Hajdrihova 19, 1000 Ljubljana (Slovenia); CO-NOT, Hajdrihova 19, Ljubljana (Slovenia)

2014-09-15

Graphical abstract: - Highlights: • Transparent pigmented coatings were deposited from titania dispersions. • Trisilanol POSS was used as dispersant. • Surface modification of pigment particles was established from TEM, TG and IR. • IR spectra studies revealed covalent and H-bond dispersant/pigment interactions. • Electrochromic properties of titanina pigment coatings were shown and discussed. - Abstract: Polyhedral oligomeric silsesqioxanes (POSS) compounds consisting of [RSiO{sub 3/2}]{sub n} groups organized in the form of various polyhedra (T{sub n}, n = 3, 6, 8, 10, 12, ….) have not often been used as pigment surface modifiers. Their interactions with pigments are not known in detail and coatings deposited from pigments modified by POSS dispersants are rare. Identification of interactions between a dispersant and the surface of pigments is important from the point of view of obtaining stable pigment dispersions enabling the deposition of optical coatings with high pigment loading, low haze and mechanical integrity. Thin TiO{sub 2} (anatase) pigment coatings (70–260 nm) were deposited from pigment dispersions prepared by milling metatitanic acid (mTiA) powder agglomerates with trisilanol heptaisobutyl silsesquioxane dispersant (trisilanol POSS) in butanol and hexane. The results of TEM, EDAX and TG measurements confirmed the influence of trisilanol POSS dispersant on the formation of a dispersion with a uniform distribution of mTiA and rutile (mTiR) nanoparticles with a size of about 30 ± 5.0 nm and 90 ± 5.0 nm, respectively, as determined from dynamic light scattering (DLS) measurements. The mTiA/trisilanol POSS dispersions with added titanium tetraisopropoxide were deposited on fluorine-doped tin oxide (FTO) coated glass (spin-coating) and indium tin oxide coated polymeric substrate (ITO PET) (coil-coating) and thermally treated at 150 °C. UV–vis spectra, AFM and SEM results showed that the pigment coatings exhibited low haze (up to 6

Electrochromic coatings made of surface modified rutile and anatase pigments: Influence of trisilanol POSS dispersant on electrochromic effect

International Nuclear Information System (INIS)

Mihelčič, Mohor; Francetič, Vojmir; Pori, Pavli; Gradišar, Helena; Kovač, Janez; Orel, Boris

2014-01-01

Graphical abstract: - Highlights: • Transparent pigmented coatings were deposited from titania dispersions. • Trisilanol POSS was used as dispersant. • Surface modification of pigment particles was established from TEM, TG and IR. • IR spectra studies revealed covalent and H-bond dispersant/pigment interactions. • Electrochromic properties of titanina pigment coatings were shown and discussed. - Abstract: Polyhedral oligomeric silsesqioxanes (POSS) compounds consisting of [RSiO 3/2 ] n groups organized in the form of various polyhedra (T n , n = 3, 6, 8, 10, 12, ….) have not often been used as pigment surface modifiers. Their interactions with pigments are not known in detail and coatings deposited from pigments modified by POSS dispersants are rare. Identification of interactions between a dispersant and the surface of pigments is important from the point of view of obtaining stable pigment dispersions enabling the deposition of optical coatings with high pigment loading, low haze and mechanical integrity. Thin TiO 2 (anatase) pigment coatings (70–260 nm) were deposited from pigment dispersions prepared by milling metatitanic acid (mTiA) powder agglomerates with trisilanol heptaisobutyl silsesquioxane dispersant (trisilanol POSS) in butanol and hexane. The results of TEM, EDAX and TG measurements confirmed the influence of trisilanol POSS dispersant on the formation of a dispersion with a uniform distribution of mTiA and rutile (mTiR) nanoparticles with a size of about 30 ± 5.0 nm and 90 ± 5.0 nm, respectively, as determined from dynamic light scattering (DLS) measurements. The mTiA/trisilanol POSS dispersions with added titanium tetraisopropoxide were deposited on fluorine-doped tin oxide (FTO) coated glass (spin-coating) and indium tin oxide coated polymeric substrate (ITO PET) (coil-coating) and thermally treated at 150 °C. UV–vis spectra, AFM and SEM results showed that the pigment coatings exhibited low haze (up to 6%), low surface

Improved electrochromical properties of sol-gel WO3 thin films by doping gold nanocrystals

International Nuclear Information System (INIS)

Naseri, N.; Azimirad, R.; Akhavan, O.; Moshfegh, A.Z.

2010-01-01

In this investigation, the effect of gold nanocrystals on the electrochromical properties of sol-gel Au doped WO 3 thin films has been studied. The Au-WO 3 thin films were dip-coated on both glass and indium tin oxide coated conducting glass substrates with various gold concentrations of 0, 3.2 and 6.4 mol%. Optical properties of the samples were studied by UV-visible spectrophotometry in a range of 300-1100 nm. The optical density spectra of the films showed the formation of gold nanoparticles in the films. The optical bandgap energy of Au-WO 3 films decreased with increasing the Au concentration. Crystalline structure of the doped films was investigated by X-ray diffractometry, which indicated formation of gold nanocrystals in amorphous WO 3 thin films. X-ray photoelectron spectroscopy (XPS) was used to study the surface chemical composition of the samples. XPS analysis indicated the presence of gold in metallic state and the formation of stoichiometric WO 3 . The electrochromic properties of the Au-WO 3 samples were also characterized using lithium-based electrolyte. It was found that doping of Au nanocrystals in WO 3 thin films improved the coloration time of the layer. In addition, it was shown that variation of Au concentration led to color change in the colored state of the Au-WO 3 thin films.

π-Extended tetrathiafulvalene BODIPY (ex-TTF-BODIPY): A redox switched "on-off-on" electrochromic system with two near-infrared fluorescent outputs

DEFF Research Database (Denmark)

Bill, N. L.; Lim, J. M.; Davis, C. M.

2014-01-01

A pi-extended tetrathiafulvalene-boradiazaindacene chimera, ex-TTF-BODIPY, has been prepared. The resulting system undergoes sequential one-electron oxidations, allowing access to both the mono-oxidized radical cationic and dicationic states. Additionally, ex-TTF-BODIPY displays electrochromic...

Redox induced switching dynamics of a three colour electrochromic metallopolymer film

International Nuclear Information System (INIS)

Zeng Qiang; McNally, Andrea; Keyes, Tia E.; Forster, Robert J.

2008-01-01

Thin films of a novel Ru-phenolate based metallopolymer, [Ru(terpy)(box)PVP 20 ]PF 6 , in which one in every twenty of the 4-vinyl pyridine monomer units is labelled with the ruthenium complex have been formed on glassy carbon electrodes, terpy is 2,2':6',2''-terpyridine, box is 2-(2-hydroxyphenyl)benzoxazole, and PVP is poly(4-vinylpyridine). Cyclic voltammetry and Raman spectroscopy reveal that the Ru 2+/3+ couple is electrochemically reversible but that the phenolate ligand based oxidation is irreversible. These redox processes are associated with reversible colour changes from wine red (reduced) to red orange (mixed composition) then to light green (oxidized) in the visible region and an irreversible change in the near-IR region, respectively. Scanning electron microscopy reveals that repeated switching in LiClO 4 aqueous solution does not induce any significant structural change within the deposit films. Cyclic voltammetry has been used to determine the electrochromic switching rate under semi-infinite linear diffusion conditions. In aqueous LiClO 4 , the homogeneous charge transport diffusion coefficient, D CT , decreases from 3.6 ± 0.3 x 10 -13 to 2.7 ± 0.2 x 10 -13 cm 2 s -1 as the LiClO 4 concentration increases from 0.1 to 1.0 M. This weak dependence of D CT on electrolyte concentration suggests that counterion availability is not rate-determining and that the overall rate of charge transport through the metallopolymer film is limited by the rate of segmental polymer chain motion necessary to bring adjacent centres sufficiently close to allow electron transfer to occur. Also the impact of changing the identity of the charge compensating anion of the redox electrochromic switching rate has been investigated. Finally, the electronic conductivity has been determined using interdigitated array electrodes (IDAs)

Integrated electrochromic iris device for low power and space-limited applications

International Nuclear Information System (INIS)

Deutschmann, T; Oesterschulze, E

2014-01-01

We present a micro-electrooptical iris based on the electrochromic polymer poly(3,4-ethylenedioxythiophene). Two ring-shaped concentric polymer-segments embedded in a transparent electrochemical cell form the micro iris. The polymer layers change their absorption when an external voltage is applied. This iris device benefits from the absence of any mechanically moving part. This renders a very slim design possible, which is suited for small integrated camera systems. During operation the polymer maintains its absorbing state without power consumption. Its low driving voltage of maximum 1.5 V is beneficial for battery powered applications. The impact of the iris on the depth of focus and transmission control as well as its dynamical behavior will be addressed. (paper)

Effects of oxygen contents on the electrochromic properties of tungsten oxide films prepared by reactive magnetron sputtering

International Nuclear Information System (INIS)

Lu, H.-H.

2008-01-01

The electrochromism have been extensively investigated due to their potential applications such as smart window of architecture and automobile glazing to save energy and modulate the transmittance of light and solar radiation. The objective of this study is to investigate the effects of sputtering conditions on the microstructure and electrochromic properties of tungsten oxide films prepared by dc reactive magnetron sputtering. Experimental results showed that the deposition rate of WO 3-y films decreased with increasing oxygen flow rate. XRD and Raman spectra analysis suggests that the WO 3-y films deposited at various oxygen flow rates are poor crystallinity or amorphous. The transmission change between colored and bleached states at a wavelength of 550 nm was 61.4% as the oxygen content was 60%. The coloration efficiency slightly increases with increasing oxygen flow rate in the low oxygen content region and reaching a maximum value of 38.94 cm 2 /C at 60% oxygen content. In addition, the films deposited at 60% oxygen content showed a good reversibility. The effects of lithium ions intercalated on the transmission of WO 3-y films were also discussed

Enhanced electrochromic and energy storage performance in mesoporous WO3 film and its application in a bi-functional smart window.

Science.gov (United States)

Wang, Wei-Qi; Wang, Xiu-Li; Xia, Xin-Hui; Yao, Zhu-Jun; Zhong, Yu; Tu, Jiang-Ping

2018-05-03

Construction of multifunctional photoelectrochemical energy devices is of great importance to energy saving. In this study, we have successfully prepared a mesoporous WO3 film on FTO glass via a facile dip-coating sol-gel method; the designed mesoporous WO3 film exhibited advantages including high transparency, good adhesion and high porosity. Also, multifunctional integrated energy storage and optical modulation ability are simultaneously achieved by the mesoporous WO3 film. Impressively, the mesoporous WO3 film exhibits a noticeable electrochromic energy storage performance with a large optical modulation up to 75.6% at 633 nm, accompanied by energy storage with a specific capacity of 75.3 mA h g-1. Furthermore, a full electrochromic energy storage window assembled with the mesoporous WO3 anode and PANI nanoparticle cathode is demonstrated with large optical modulation and good long-term stability. Our research provides a new route to realize the coincident utilization of optical-electrochemical energy.

Toward Plastic Smart Windows: Optimization of Indium Tin Oxide Electrodes for the Synthesis of Electrochromic Devices on Polycarbonate Substrates.

Science.gov (United States)

Laurenti, Marco; Bianco, Stefano; Castellino, Micaela; Garino, Nadia; Virga, Alessandro; Pirri, Candido F; Mandracci, Pietro

2016-03-01

Plastic smart windows are becoming one of the key elements in view of the fabrication of inexpensive, lightweight electrochromic (EC) devices to be integrated in the new generation of high-energy-efficiency buildings and automotive applications. However, fabricating electrochromic devices on polymer substrates requires a reduction of process temperature, so in this work we focus on the development of a completely room-temperature deposition process aimed at the preparation of ITO-coated polycarbonate (PC) structures acting as transparent and conductive plastic supports. Without providing any substrate heating or surface activation pretreatments of the polymer, different deposition conditions are used for growing indium tin oxide (ITO) thin films by the radiofrequency magnetron sputtering technique. According to the characterization results, the set of optimal deposition parameters is selected to deposit ITO electrodes having high optical transmittance in the visible range (∼90%) together with low sheet resistance (∼8 ohm/sq). The as-prepared ITO/PC structures are then successfully tested as conductive supports for the fabrication of plastic smart windows. To this purpose, tungsten trioxide thin films are deposited by the reactive sputtering technique on the ITO/PC structures, and the resulting single electrode EC devices are characterized by chronoamperometric experiments and cyclic voltammetry. The fast switching response between colored and bleached states, together with the stability and reversibility of their electrochromic behavior after several cycling tests, are considered to be representative of the high quality of the EC film but especially of the ITO electrode. Indeed, even if no adhesion promoters, additional surface activation pretreatments, or substrate heating were used to promote the mechanical adhesion among the electrode and the PC surface, the observed EC response confirmed that the developed materials can be successfully employed for the

Electrochemistry of poly(3,4-ethylenedioxythiophene)-polyaniline/ Prussian blue electrochromic devices containing an ionic liquid based gel electrolyte film.

Science.gov (United States)

Deepa, Melepurath; Awadhia, Arvind; Bhandari, Shweta

2009-07-21

Electrochromic devices based on poly(3,4-ethylenedioxythiophene) (PEDOT) as the cathodic coloring electrode and polyaniline (PANI) or Prussian blue (PB) as the counter electrode containing a highly conductive, self-supporting, distensible and transparent polymer-gel electrolyte film encapsulating an ionic liquid, 1-butyl-1-methylpyrrolidiniumbis-(trifluoromethylsulfonyl)imide, have been fabricated. Polarization, charge transfer and diffusion processes control the electrochemistry of the functional electrodes during coloration and bleaching and these phenomena differ when PEDOT and PANI/PB were employed alternately as working electrodes. While the electrochemical impedance response shows good similitude for PEDOT and PANI electrodes, the responses of PEDOT and PB were significantly different in the PEDOT-PB device, especially during reduction of PB, wherein the overall amplitude of the impedance response is enormous. Large values of the coloration efficiency maxima of 281 cm2 C(-1) (lambda = 583 nm) and 274 cm2 C(-1) (lambda = 602 nm), achieved at -1.0 and -1.5 V for the PEDOT PANI and PEDOT-PB devices have been correlated to the particularly low magnitude of charge transfer resistance and high polarization capacitance operative at the PEDOT ionic liquid based electrolyte interface at these dc potentials, thus allowing facile ion-transport and consequently resulting in enhanced absorption modulation. Moderately fast switching kinetics and the ability of these devices to sustain about 2500 cycles of clear-to-dark and dark-to-clear without incurring major losses in the optical contrast, along with the ease of construction of these cells in terms of high scalability and reproducibility of the synthetic procedure for fabrication of the electrochromic films and the ionic liquid based gel electrolyte film, are indicators of the promise these devices hold for practical applications like electrochromic windows and displays.

Fast printing of thin, large area, ITO free electrochromics on flexible barrier foil

DEFF Research Database (Denmark)

Søndergaard, Roar R.; Hösel, Markus; Jørgensen, Mikkel

2013-01-01

Processing of large area, indium tin oxide (ITO) free electrochromic (EC) devices has been carried out using roll-toroll (R2R) processing. By use of very fine high-conductive silver grids with a hexagonal structure, it is possible to achieve good transparency of the electrode covered substrates...... and when used in EC devices switching times are similar to corresponding ITO devices. This is obtained without the uneven switching of larger areas, which is generally observed when using ITO because of its high-sheet resistance. The silver electrode structures for 18 ×18 cm2 devices can be processed...

Preparations and characterizations of tunable and multicolored electrochromic copolymers derived from a novel star-shaped monomer and BEDOT-V

International Nuclear Information System (INIS)

Wang, Kai; Yang, Wenge; Hu, Yonghong; Kai, Yumei; Shi, Ying

2014-01-01

A novel star-shaped monomer 1,3,5-Tri[2-(3,4-ethylenedioxythien-2-yl)vin-1-yl]benzene (TEDOT-V-B) was synthesized by Wittig coupling reaction. The copolymers with BEDOT-V at different feed ratios were prepared onto the ITO-coated glass by cyclic voltammetry (CV) method and the electrochromic properties were reported. The influences of different feed ratios on the spectroelectrochemical and kinetic properties were investigated. Spectroelectrochemical studies indicated that the maximum absorption wavelengths of the copolymer films bathochromically shifted with feed ratios. In addition, the copolymers had tunable and low band gaps. When the feed ratio of BEDOT-V-B/BEDOT-V was 1:3, the copolymer film showed the fastest oxidation switching time of 0.9s (567 nm) and 0.9s (967 nm) and the fastest reduction switching time of 0.8s (567 nm) and 0.9s (967 nm). Compared with PBEDOT-V, the copolymers showed tunable and multicolored electrochromism through feed ratios and the RGB colors were achieved. Additionally, the surface morphology of the copolymer film was investigated by scanning electron microscope (SEM)

Solution processed large area fabrication of Ag patterns as electrodes for flexible heaters, electrochromics and organic solar cells

DEFF Research Database (Denmark)

Gupta, Ritu; Walia, Sunil; Hösel, Markus

2014-01-01

, the process takes only a few minutes without any expensive instrumentation. The electrodes exhibited excellent adhesion and mechanical properties, important for flexible device application. Using Ag patterned electrodes, heaters operating at low voltages, pixelated electrochromic displays as well as organic...... solar cells have been demonstrated. The method is extendable to produce defect-free patterns over large areas as demonstrated by roll coating....

Amorphous ITO thin films prepared by DC sputtering for electrochromic applications

International Nuclear Information System (INIS)

Teixeira, V.; Cui, H.N.; Meng, L.J.; Fortunato, E.; Martins, R.

2002-01-01

Indium-Tin-Oxide (ITO) thin films were deposited on glass substrates using DC magnetron reactive sputtering at different bias voltages and substrate temperatures. Some improvements were obtained on film properties, microstructure and other physical characteristics for different conditions. Amorphous and polycrystalline films can be obtained for various deposition conditions. The transmission, absorption, spectral and diffuse reflection of ITO films were measured in some ranges of UV-Vis-NIR. The refractive index (n), Energy band gap E g and the surface roughness of the film were derived from the measured spectra data. The carrier density (n c ) and the carrier mobility (μ) of the film micro conductive properties were discussed. The films exhibited suitable optical transmittance and conductivity for electrochromic applications

Electrochromic in conjugated polymers

International Nuclear Information System (INIS)

Picado Valenzuela, Alfredo

2007-01-01

This revision considered object the description of one of the materials with the greatest potential in the field of electrochromic (mainly in the visible region): the conjugated polymers (CP), area of enormous potential both now and in a short time ahead. The CP are insulating materials and organic semiconductors in a state not doped. They can be doped positively or negatively being observed a significant increase in the conductivity and being generated a color change in these materials. The understanding of how optical properties vary based on the chemical structure of the polymer or its mixtures and more precisely of the alternatives that can be entered into the conjugated system or π system to obtain a material that besides to be flexible, environmentally stable, presents the colored states. The revision was centred chiefly in the polypyrrole (Ppy), the polythiophene (PTh) and their derivatives such as poly (3.4-ethylenedioxythiophene) (PEDOT). The advantage of using monomers with variable structure, to adjust the composition of the copolymer, or to blend with the PC, allows to obtain a variety of colored states that can be modulated through the visible spectrum and even with applications to wavelengths outside of this region. Because the PC presented at least two different colored states can be varied continuously as a function of the voltage applied. In some cases, they may submit multicoloured statements, which offers a range of possibilities for their application in flexible electronic devices type screens and windows. Applications include smart windows, camouflage clothing and data screens. This type of material is emerging as one of the substitutes of the traditional inorganic semiconductor, with the advantage of its low cost, high flexibility and the possibility to generate multiple colors through the handling of the monomers in the structure and control of energy of his band gap. (author) [es

Integrated electrochromic aperture diaphragm

Science.gov (United States)

Deutschmann, T.; Oesterschulze, E.

2014-05-01

In the last years, the triumphal march of handheld electronics with integrated cameras has opened amazing fields for small high performing optical systems. For this purpose miniaturized iris apertures are of practical importance because they are essential to control both the dynamic range of the imaging system and the depth of focus. Therefore, we invented a micro optical iris based on an electrochromic (EC) material. This material changes its absorption in response to an applied voltage. A coaxial arrangement of annular rings of the EC material is used to establish an iris aperture without need of any mechanical moving parts. The advantages of this device do not only arise from the space-saving design with a thickness of the device layer of 50μm. But it also benefits from low power consumption. In fact, its transmission state is stable in an open circuit, phrased memory effect. Only changes of the absorption require a voltage of up to 2 V. In contrast to mechanical iris apertures the absorption may be controlled on an analog scale offering the opportunity for apodization. These properties make our device the ideal candidate for battery powered and space-saving systems. We present optical measurements concerning control of the transmitted intensity and depth of focus, and studies dealing with switching times, light scattering, and stability. While the EC polymer used in this study still has limitations concerning color and contrast, the presented device features all functions of an iris aperture. In contrast to conventional devices it offers some special features. Owing to the variable chemistry of the EC material, its spectral response may be adjusted to certain applications like color filtering in different spectral regimes (UV, optical range, infrared). Furthermore, all segments may be switched individually to establish functions like spatial Fourier filtering or lateral tunable intensity filters.

Influence of stoichiometry on electrochromic cerium-titanium oxide compounds

International Nuclear Information System (INIS)

Kullman, L.; Richardson, T.; Rubin, M.; Slack, J.; Rottkay, K. von

1997-01-01

CeO 2 -TiO 2 finds use as passive counter-electrode in electrochromic devices. Thin films were produced by de-sputtering in a wide range of compositions. Influence of total pressure and oxygen partial pressure on the optical constants of TiO 2 was investigated. Slightly substoichiometric Ti0 2 films exhibit a red-shift of the bandgap. The Ti0 2 content in the compound essentially determines the degree of cathodical coloring upon Li + intercalation [1]. However, pure TiO 2 films with comparable visible transmittance in the clear state behave differently during electrochemical cycling depending on oxygen stoichiometry. Films that are deposited at higher total pressure are more oxygen rich and require initial formatting until current voltage cycles become stable. CeO 2 -Ti0 2 films of intermediate compositions have the relatively highest charge capacity. Comparison with atomic force microscopy indicates a correlation of small grain size with high charge capacity

One-step inkjet printing of tungsten oxide-poly(3,4-ethylenedioxythiophene):polystyrene sulphonate hybrid film and its applications in electrochromic devices

Energy Technology Data Exchange (ETDEWEB)

Nguyen, Thi-Thuy-Nga, E-mail: thuysnga@gmail.com; Chan, Chih-Yu; He, Ju-Liang

2016-03-31

Hybrid film comprised tungsten oxide and poly (3,4-ethylenedioxythiophene):polystyrene sulphonate (WO{sub 3}–PEDOT:PSS) was developed by applying one-step inkjet printing from an office inkjet printer. The WO{sub 3} nanoparticles were synthesized from commercial crystalline WO{sub 3} powder through a wet ball-milling process, which is a simple, environmentally friendly, and cost-effective method of using water as a green solvent and low-energy milling. The WO{sub 3}–PEDOT:PSS inkjet ink was prepared by dispersing the as-milled WO{sub 3} and PEDOT:PSS in n-propanol and deionized water. The inkjet-printed WO{sub 3}–PEDOT:PSS thin films show marked improvements of cathodic electrochromism over WO{sub 3} films: the transmittance change of 20% at 550 nm (visible region) and 35% at 900 nm (infrared region) along with the response time of 5.67/0.30 s in their colored/bleached state, and the electrochromic coloration efficiency of 27.86 cm{sup 2}/C at 550 nm and 69.64 cm{sup 2}/C at 900 nm. - Highlights: • WO{sub 3} nanoparticles were synthesized by milling commercial crystalline WO{sub 3}. • Wet ball-milling was carried out by using water as a green solvent and low energy. • WO{sub 3}–PEDOT:PSS hybrid ink was simply prepared by adding n-propanol and DI water. • WO{sub 3}–PEDOT:PSS hybrid films were inkjet-printed via an office inkjet printer. • WO{sub 3}–PEDOT:PSS films show better electrochromic performances than WO{sub 3} films.

A Pilot Demonstration of Electrochromic and Thermochromic Windows in the Denver Federal Center, Building 41, Denver, Colorado

Energy Technology Data Exchange (ETDEWEB)

Lee, Eleanor S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Fernandes, Luis L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Goudey, Chad Howdy [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Jonsson, Carl Jacob [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Curcija, D. Charlie [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Pang, Xiufeng [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); DiBartolomeo, Dennis [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Hoffmann, Sabine [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2013-07-01

Chromogenic glazing materials are emerging technologies that tint reversibly from a clear to dark tinted state either passively in response to environmental conditions or actively in response to a command from a switch or building automation system. Switchable coatings on glass manage solar radiation and visible light while enabling unobstructed views to the outdoors. Building energy simulations estimate that actively controlled, near-term chromogenic glazings can reduce perimeter zone heating, ventilation, and airconditioning (HVAC) and lighting energy use by 10-20% and reduce peak electricity demand by 20-30%, achieving energy use levels that are lower than an opaque, insulated wall. This project demonstrates the use of two types of chromogenic windows: thermochromic and electrochromic windows. By 2013, these windows will begin production in the U.S. by multiple vendors at high-volume manufacturing plants, enabling lower cost and larger area window products to be specified. Both technologies are in the late R&D stage of development, where cost reductions and performance improvements are underway. Electrochromic windows have been installed in numerous buildings over the past four years, but monitored energy-efficiency performance has been independently evaluated in very limited applications. Thermochromic windows have been installed in one other building with an independent evaluation, but results have not yet been made public.

In situ preparation of composite from conjugated polyschiff bases and multiwalled carbon nanotube: Synthesis, electrochromic, acidochromic properties

International Nuclear Information System (INIS)

Ma Lina; Cai Jiwei; Zhao Ping; Niu Haijun; Wang Cheng; Bai Xuduo; Wang Wen

2012-01-01

Graphical abstract: The introduction of carbon nanotubes greatly improves the photochromic property of the composites. Highlights: ► MWNTs/PSB composite was prepared by in situ polymerization with a new type of PSB. ► The introduction of carbon nanotubes greatly improves the photochromic property of the composites. ► The composites exhibited excellent thermal stability and reversible electrochemical behavior. - Abstract: Polyschiff base (PSB) which has the structure of C=N double bond is well known as conducting material with high thermal resistance, chemical and electrical properties. Recently, it was used as hole transporting material in organic light emitting diode (OLED), chemical sensor and electrochromic materials. Carbon nanotubes (CNTs) with excellent properties such as unique electrical, mechanical, optical and chemical properties are promising reinforcing materials for polymer composites which improve the comprehensive properties of polymers. In this paper, conjugated PSB-grafted multiwalled carbon nanotubes (MWNTs) composite was prepared by in situ polymerization. The resultant composites were characterized by thermogravimetric (TGA), scanning electron microscopy (SEM), UV–vis absorption, photoluminescence (PL), cyclic voltammograms (CV), infrared spectroscopy (IR) and Raman spectroscopy. The composites exhibited high thermal stability and excellent reversibilities of electrochromic, photochromic, acidochromic characteristics, with the color change from the light yellow to blue.

The approach of in-situ doping ion conductor fabricated with the cathodic arc plasma for all-solid-state electrochromic devices

Directory of Open Access Journals (Sweden)

Min-Chuan Wang

2018-01-01

Full Text Available The all-solid-state electrochromic device (ECD with the one substrate structure fabricated by the reactive dc magnetron sputtering (DCMS and in-situ doping cathodic vacuum arc plasma (CVAP technology has been developed. The electrochromic (EC layer and ion conductor layer were deposited by reactive DCMS and CVAP technology, respectively. The in-situ doping ion conductor Ta2O5 deposited by the CVAP technology has provided the better material structure for ion transportation and showed about 2 times ion conductivity than the external doping process. The all-solid-state ECD with the in-situ doping CVAP ion conductor layer has demonstrated a maximum transmittance variation (ΔT of 71% at 550 nm, and a faster switching speed. The lower production cost and higher process stability could be achieved by the application of in-situ doping CVAP technology without breaking the vacuum process. Furthermore, the ion doping process with the reuse of energy during the CVAP process is not only decreasing the process steps, but also reducing the process energy consumption.

Novel electrochromic devices based on composite films of poly(2,5-dimethoxyaniline)-waterborne polyurethane

International Nuclear Information System (INIS)

Yang, C.-H.; Chong, L.-W.; Huang, L.-M.; Lee, Y.-L.; Wen, T.-C.

2005-01-01

Waterborne polyurethane (WPU) was spin-coated on indium tin oxide (ITO) coated glass. Poly(2,5-dimethoxyaniline) (PDMA) was deposited using electrochemical polymerization as conducting composite film on the above WPU/ITO electrode and used as an electrode in an electrochromic device assembly. Tungsten oxide (WO 3 ) coated ITO glass was used as the other electrode with LiClO 4 doped gelled polyethylene oxide (PEO) as polymer electrolyte. The configuration of an electrochromic device was assembled: ITO/WPU-PDMA II LiClO 4 -PC-PEO (400,000) II WO 3 /ITO, where PC represents propylene carbonate. The characterization of the single electrodes, ITO/WPU-PDMA composite, ITO/WO 3 , and the device was performed by using cyclic voltammetry. The columbic efficiency (CE) of the ITO/WPU-PDMA composite and ITO/WO 3 electrodes were close to 100%. The optical contrast of the single electrodes and the device were determined by UV-vis spectroelectrochemical studies. A visible contrast in color upon switching the potential from -1.50 to +1.50 V was noticed for the device. The device was pale yellow at -1.5 V and dark green at +1.5 V. The CE of the device was 91%. Double potential chronamperomtry was used to determine the response time of coloring and bleaching processes. The bleaching process was found to be faster than coloring. The stability of the device was established by polarizing the device and recording the UV-vis spectrum in open circuit conditions. Bleaching state is more stable than coloring state

Spin coated versus dip coated electrochromic tungsten oxide films: Structure, morphology, optical and electrochemical properties

International Nuclear Information System (INIS)

Deepa, M.; Saxena, T.K.; Singh, D.P.; Sood, K.N.; Agnihotry, S.A.

2006-01-01

A sol-gel derived acetylated peroxotungstic acid sol encompassing 4 wt.% of oxalic acid dihydrate (OAD) has been employed for the deposition of tungsten oxide (WO 3 ) films by spin coating and dip coating techniques, in view of smart window applications. The morphological and structural evolution of the as-deposited spin and dip coated films as a function of annealing temperature (250 and 500 o C) has been examined and compared by Fourier transform infrared (FT-IR) spectroscopy, scanning electron microscopy (SEM) and X-ray diffraction (XRD). A conspicuous feature of the dip coated film (annealed at 250 o C) is that its electrochromic and electrochemical properties ameliorate with cycling without degradation in contrast to the spin coated film for which these properties deteriorate under repetitive cycling. A comparative study of spin and dip coated nanostructured thin films (annealed at 250 o C) revealed a superior performance for the cycled dip coated film in terms of higher transmission modulation and coloration efficiency in solar and photopic regions, faster switching speed, higher electrochemical activity as well as charge storage capacity. While the dip coated film could endure 2500 color-bleach cycles, the spin coated film could sustain only a 1000 cycles. The better cycling stability of the dip coated film which is a repercussion of a balance between optimal water content, porosity and grain size hints at its potential for electrochromic window applications

Structure, electrochromic and optical properties of WO3 film prepared by dip coating-pyrolysis

International Nuclear Information System (INIS)

Yang Haitao; Shang Fuliang; Gao Ling; Han Haitao

2007-01-01

The tungsten oxide (WO 3 ) film was grown by dip coating-pyrolysis method with the PEG-400 as the structure-directing agent. Microstructure of the WO 3 film was characterized by TG-DSC, XRD and SEM techniques. It was found that the film annealed at 350 deg. C for 2 h comprised cubic WO 3 and orthorhombic WO 3 . The measurements of the cyclic voltammetry (CV) and UV-vis spectrum suggested that the WO 3 film had a good electrochromic reversibility performance. The film possessed excellent modulation to the visible light and the maximal average transmittance modulation reached 70.06%

Doping, Ionic Conductivity and Photothermal Stability of Functionalized DNA for Solar Energy Conversion and Electrochromic Applications

Science.gov (United States)

2011-06-01

and coworkers 1,2,3,4 . They are renewable and biodegradable materials, recovered from waste in food industry (fruits, animal and fish meat waste) and...charges leads to the change of its absorption spectrum, or in other words to a change of its color . However in most cases the electrolyte used is in...electrodes (cf. Fig. 25). CeO2- TiO2 BK7 BK7 SOLID ELECTROLYTE ITO WO3 ITO Fig. 25. Structure of the used electrochromic cell 21 Figure 26

A new processable electrochromic polymer based on an electron deficient fluorene derivative with a high coloration efficiency

International Nuclear Information System (INIS)

Çarbaş, Buket Bezgin; Kivrak, Arif; Önal, Ahmet M.

2011-01-01

Highlights: ► Electrochemical synthesis and elecroptical properties of a new soluble polymer based on fluorenone and 3,4-propylenedioxythiophene are highlighted. ► The polymer film exhibits reversible electrochromic behavior and both p and n dopable. ► In addition it has high electrochemical stability and coloration efficiency. ► In THF, polymer film emits orange light when excited at 355 nm. - Abstract: A new fluorenone based soluble polymer, namely poly(2,7-bis-(3,3-dihexyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepin-6-yl) -fluoren-9-one) (PPFP), containing propylenedioxythiophene (ProDOT) as a donor and fluorenone (FO) as an acceptor group is highlighted. Electrochemical polymerization of 2,7-bis-(3,3-dihexyl-3,4-dihydro-2H-thieno[3,4-b][1,4]dioxepin-6-yl) -fluoren-9-one (PFP) was achieved in dichloromethane/acetonitrile mixture with 0.1 M tetrabutylammonium hexafluorophosphate via potential cycling. The polymer shows an electrochromic behavior, a color change from orange to dark blue during oxidation with a high coloration efficiency (422 cm 2 /C at 684 nm) and orange to yellow during reduction with high optical and electrochemical stability as compared to its close analogues, in addition it is found to be both p and n dopable. Furthermore, this soluble polymer exhibits fluorescent properties (the emission of orange light (578 nm) in THF solution).

Electro-optical evaluation of tungsten oxide and vanadium pentoxide thin films for modeling an electrochromic device

Directory of Open Access Journals (Sweden)

H Najafi Ashtiani

2015-01-01

Full Text Available In this study, tungsten oxide and vanadium oxide electrochromic thin films were placed in vacuum and in a thickness of 200 nm on a transparent conductive substrate of SnO2:F using the physical method of thermal evaporation. Then they were studied for the optical characteristics in the wavelength range from 400 to 700 nm and for their electrical potentials in the range form +1.5 to -1.5 volts. The films were post heated in order to assess changes in energy gap with temperature, at temperatures120 , 300 and 500°C. Refractive and extinction coefficients and the transition type of films in the visible light range and in the thickness of 200 nm were determined and measured. X-ray diffraction pattern and SEM images and cyclic Voltammetry of layers were also studied. The results of this study due to the deposition of layers, the layer thickness selected, the type of substrate, the range of annealing temperatures and selected electrolyte were in full compliance with the works of other researchers [1,2,3]. Therefore, these layers with features such as crystal structure, refractive and even extinction coefficients in the range of visible light, the appropriate response of chromic switch in the replication potential, good adhesion to the substrate, and the high amount of optical transmition and so on, prove useful to be used in an electrochromic device

BIPV-powered smart windows utilizing photovoltaic and electrochromic devices.

Science.gov (United States)

Ma, Rong-Hua; Chen, Yu-Chia

2012-01-01

A BIPV-powered smart window comprising a building-integrated photovoltaic (BIPV) panel and an all-solid-state electrochromic (EC) stack is proposed. In the proposed device, the output voltage of the BIPV panel varies in accordance with the intensity of the incident light and is modulated in such a way as to generate the EC stack voltage required to maintain the indoor illuminance within a specified range. Two different EC stacks are fabricated and characterized, namely one stack comprising ITO/WO(3)/Ta(2)O(5)/ITO and one stack comprising ITO/WO(3)/lithium-polymer electrolyte/ITO. It is shown that of the two stacks, the ITO/WO(3)/lithium-polymer electrolyte/ITO stack has a larger absorptance (i.e., approximately 99% at a driving voltage of 3.5 V). The experimental results show that the smart window incorporating an ITO/WO(3)/lithium-polymer electrolyte/ITO stack with an electrolyte thickness of 1.0 μm provides an indoor illuminance range of 750-1,500 Lux under typical summertime conditions in Taiwan.

BIPV-Powered Smart Windows Utilizing Photovoltaic and Electrochromic Devices

Directory of Open Access Journals (Sweden)

Yu-Chia Chen

2011-12-01

Full Text Available A BIPV-powered smart window comprising a building-integrated photovoltaic (BIPV panel and an all-solid-state electrochromic (EC stack is proposed. In the proposed device, the output voltage of the BIPV panel varies in accordance with the intensity of the incident light and is modulated in such a way as to generate the EC stack voltage required to maintain the indoor illuminance within a specified range. Two different EC stacks are fabricated and characterized, namely one stack comprising ITO/WO3/Ta2O5/ITO and one stack comprising ITO/WO3/lithium-polymer electrolyte/ITO. It is shown that of the two stacks, the ITO/WO3/lithium-polymer electrolyte/ITO stack has a larger absorptance (i.e., approximately 99% at a driving voltage of 3.5 V. The experimental results show that the smart window incorporating an ITO/WO3/lithium-polymer electrolyte/ITO stack with an electrolyte thickness of 1.0 μm provides an indoor illuminance range of 750–1,500 Lux under typical summertime conditions in Taiwan.

Nanomaterials for benign indoor environments: Electrochromics for 'smart windows', sensors for air quality, and photo-catalysts for air cleaning

International Nuclear Information System (INIS)

Granqvist, C.G.; Azens, A.; Heszler, P.; Kish, L.B.; OEsterlund, L.

2007-01-01

Nanomaterials can be used in a number of technologies in order to accomplish benign indoor environments. This paper takes a unified view on this problem from a solar-energy-based perspective and specifically considers electrochromics for achieving good day-lighting jointly with energy efficiency, sensors aimed at air quality assessment, and photocatalysis for air cleaning. Recent results, mainly from the authors' laboratories, are reported for all of these areas. (author)

Investigation of water content in electrolyte solution on electrochromic properties of WO3 thin Films

Directory of Open Access Journals (Sweden)

Zahra Abadi

2017-05-01

Full Text Available Tungsten oxide thin films were prepared by a cathodic electrodeposition method at -0.450 mV in order to investigate how water content affects their electrochromic properties. FESEM images exhibit that WO3 thin films consist of 65 nm uniform grains. Thin Films were electrochemically investigated in 0.1M LiClO4 in propylene carbonate electrolyte with and without 5vol% water content by cyclic voltammetry and chronoamperometry. The results indicate that tungsten oxide thin films exhibit faster switching time between coloration and bleaching states and also higher coloration efficiency in hydrated electrolyte.  

Focused R&D For Electrochromic Smart Windowsa: Significant Performance and Yield Enhancements

Energy Technology Data Exchange (ETDEWEB)

Mark Burdis; Neil Sbar

2003-01-31

There is a need to improve the energy efficiency of building envelopes as they are the primary factor governing the heating, cooling, lighting and ventilation requirements of buildings--influencing 53% of building energy use. In particular, windows contribute significantly to the overall energy performance of building envelopes, thus there is a need to develop advanced energy efficient window and glazing systems. Electrochromic (EC) windows represent the next generation of advanced glazing technology that will (1) reduce the energy consumed in buildings, (2) improve the overall comfort of the building occupants, and (3) improve the thermal performance of the building envelope. ''Switchable'' EC windows provide, on demand, dynamic control of visible light, solar heat gain, and glare without blocking the view. As exterior light levels change, the window's performance can be electronically adjusted to suit conditions. A schematic illustrating how SageGlass{reg_sign} electrochromic windows work is shown in Figure I.1. SageGlass{reg_sign} EC glazings offer the potential to save cooling and lighting costs, with the added benefit of improving thermal and visual comfort. Control over solar heat gain will also result in the use of smaller HVAC equipment. If a step change in the energy efficiency and performance of buildings is to be achieved, there is a clear need to bring EC technology to the marketplace. This project addresses accelerating the widespread introduction of EC windows in buildings and thus maximizing total energy savings in the U.S. and worldwide. We report on R&D activities to improve the optical performance needed to broadly penetrate the full range of architectural markets. Also, processing enhancements have been implemented to reduce manufacturing costs. Finally, tests are being conducted to demonstrate the durability of the EC device and the dual pane insulating glass unit (IGU) to be at least equal to that of conventional

Tungsten Trioxide/Zinc Tungstate Bilayers: Electrochromic Behaviors, Energy Storage and Electron Transfer

International Nuclear Information System (INIS)

Wei, Huige; Ding, Daowei; Yan, Xingru; Guo, Jiang; Shao, Lu; Chen, Haoran; Sun, Luyi; Colorado, Henry A.; Wei, Suying; Guo, Zhanhu

2014-01-01

Highlights: • Tungsten oxide and zinc tungstate bilayers have been prepared via a facile sol-gel method for integrated applications of electrochromic behaviors and energy storage;. • Electron transfer behaviors between the semiconductor bilayer films have been found dependent on the bilayer assembly sequence;. • Methylene blue (MB) has been employed for the first time as an indicator to study the electron transfer phenomenon in the bilayer films. - Abstract: Pair-sequentially spin-coated tungsten trioxide (WO 3 ) and zinc tungstate (ZnWO 4 ) bilayer films onto indium tin oxide (ITO) coated glass slides have been prepared via sol-gel methods followed by annealing. The bilayers (ZnWO 4 /WO 3 denoting the bilayer film with the inner layer of ZnWO 4 and the outer layer of WO 3 on the ITO while WO 3 /ZnWO 4 standing for the bilayer film with the inner layer of WO 3 and the outer layer of ZnWO 4 on the ITO) exhibit integrated functions of electrochromic and energy storage behaviors as indicated by the in situ spectroelectrochemistry and cyclic voltammetry (CV) results. Accordingly, blue color was observed for the bilayer films at -1 V in 0.5 M H 2 SO 4 solution. An areal capacitance of 140 and 230 μF/cm 2 was obtained for the ZnWO 4 /WO 3 , and WO 3 /ZnWO 4 film, respectively, at a scan rate of 0.05 V/s in the CV measurements. The CV results also unveiled the electron transfer behavior between the semiconductor films in the oxidation process, suggesting a sequence-dependent electrochemical response in the bilayer films. Meanwhile, methylene blue (MB) was used as an indicator to study the electron transfer phenomenon during the reduction process at negative potentials of -0.4 and -0.8 V, in 0.5 M Na 2 SO 4 . The results indicated that the electrons transfer across the bilayers was enhanced at more negative potentials

Melt sonoquenching: an affective process to obtain new hybrid material and achieve enhanced electrochromic performances based on V{sub 2}O{sub 5}/2,4,5-tris(1-methyl- 4-pyridinium)-imidazolide tetrafluoroborate nanofibers

Energy Technology Data Exchange (ETDEWEB)

Oliveira, Renato S. de; Goulart, Juliana da S.; Miranda, Fabio S.; Ponzio, Eduardo A., E-mail: eaponzio@vm.uff.br [Universidade Federal Fluminense (UFF), Niteroi, RJ (Brazil). Instituto de Quimica

2014-03-15

Hybrid electrochromic materials are a very important class of compounds, because they enable new and/or better optical and electrochemical properties to be unfolded. This paper reports the synthesis of the new V{sub 2}O{sub 5}.1.26H{sub 2}O([C{sub 3}N{sub 2}(C{sub 6}H{sub 7}N){sub 3}]){sub 0.07} using the combination of two traditional methods, melting quenching and sonochemistry. The new material was characterized by several methods in order to verify the physical and chemical characteristics and its possible use as an electrochromic electrode. The organic guest provokes an interlayer spacing decrease of the inorganic matrix and the electrostatic interaction between the oxo groups of the V{sub 2}O{sub 5} matrix and the pyridinium rings of the organic guest demonstrate a strong interaction. The new hybrid nanostructure presented good reversibility and cyclability during 50 cycles, electrochromic efficiency of 22 cm{sup 2} C{sup -1} (410 nm) and 96 % color retention after 50 cycles of color changing. (author)'.

Remarkable ability to modulate light transmittance and block heat in the bleached state combined in one electrochromic material: highly crystalline polyaniline

Czech Academy of Sciences Publication Activity Database

Gospodinova, Natalia; Skorokhoda, Taras; Lobaz, Volodymyr

2018-01-01

Roč. 51, č. 6 (2018), s. 2227-2231 ISSN 0024-9297 R&D Projects: GA ČR(CZ) GA15-14791S Grant - others:OPPK(XE) CZ.2.16/3.1.00/21545 Program:OPPK Institutional support: RVO:61389013 Keywords : electrochromic * chain ordering * conducting polymers Subject RIV: CF - Physical ; Theoretical Chemistry OBOR OECD: Physical chemistry Impact factor: 5.835, year: 2016

Retrofit electrochromic glazing in a UK office

Directory of Open Access Journals (Sweden)

Ruth Kelly Waskett

2014-12-01

Full Text Available Electrochromic (EC glazing is now considered a viable alternative to fixed transmittance glazing. It has the potential to enable occupants to control daylight glare and solar heat gain without the use of blinds or external shading devices, giving users more access to daylight with all its inherent benefits. Furthermore, EC glazing can reduce energy consumption by decreasing cooling loads and electric lighting usage. Most research to date has studied the effects of EC glazing in scale models, computer simulations and full scale test rooms, and some of these studies have included human participants. However, there is a general lack of understanding regarding the performance and suitability of EC glazing in real-world working environments. A case study of the first UK retrofit application of EC glazing is being conducted in two adjacent offices in a university campus building. The offices are occupied by administration staff and have large southeastfacing windows. The existing double glazed units were replaced with commercially-available EC glazed units in 2012. Over a period of more than 18 months, the rooms were monitored intensively to record the effect of the EC glazing on both the physical room environment and the occupants themselves. A large amount of data from the monitoring programme is currently undergoing detailed analysis. Initial findings emerging from the installation and post-installation period are described in this paper.

Electrochromic Windows: Advanced Processing Technology

Energy Technology Data Exchange (ETDEWEB)

SAGE Electrochromics, Inc

2006-12-13

This project addresses the development of advanced fabrication capabilities for energy saving electrochromic (EC) windows. SAGE EC windows consist of an inorganic stack of thin films deposited onto a glass substrate. The window tint can be reversibly changed by the application of a low power dc voltage. This property can be used to modulate the amount of light and heat entering buildings (or vehicles) through the glazings. By judicious management of this so-called solar heat gain, it is possible to derive significant energy savings due to reductions in heating lighting, and air conditioning (HVAC). Several areas of SAGE’s production were targeted during this project to allow significant improvements to processing throughput, yield and overall quality of the processing, in an effort to reduce the cost and thereby improve the market penetration. First, the overall thin film process was optimized to allow a more robust set of operating points to be used, thereby maximizing the yield due to the thin film deposition themselves. Other significant efforts aimed at improving yield were relating to implementing new procedures and processes for the manufacturing process, to improve the quality of the substrate preparation, and the quality of the IGU fabrication. Furthermore, methods for reworking defective devices were developed, to enable devices which would otherwise be scrapped to be made into useful product. This involved the in-house development of some customized equipment. Finally, the improvements made during this project were validated to ensure that they did not impact the exceptional durability of the SageGlass® products. Given conservative estimates for cost and market penetration, energy savings due to EC windows in residences in the US are calculated to be of the order 0.026 quad (0.026×1015BTU/yr) by the year 2017.

Electrochromism and Swelling of Polypyrrole Membranes: An Electrochemical and Ellipsometric Study

Directory of Open Access Journals (Sweden)

J. O. Zerbino

2011-01-01

Full Text Available The growth of polypyrrole (Ppy layers on gold electrodes in nearly neutral pH solutions is analysed using “in situ” voltametric and ellipsometric techniques. Different film structures are obtained depending on the potentiodynamic programme and the composition of the electrolyte. More compact dodecylsulphate-(DS doped Ppy layers were grown at 1.2 V versus RHE than those obtained by applying a higher potential. The more compact layers correspond to the growth of an oxidised Ppy/DS layer that shows low pseudo capacity behaviour. After dipping, the doped Ppy/DS film in KCl solution-significant variations in optical indices and thickness are detected as a function of the applied potential. Higher electrochromism as well as decrease in film thickness after cathodisation is achieved. The optical indices and the thickness of the Ppy layer formed under different applied potential/time programmes are estimated.

Improvement of the electrochromic response of a low-temperature sintered dye-modified porous electrode using low-resistivity indium tin oxide nanoparticles

International Nuclear Information System (INIS)

Watanabe, Yuichi; Suemori, Kouji; Hoshino, Satoshi

2016-01-01

An indium tin oxide (ITO) nanoparticle-based porous electrode sintered at low temperatures was investigated as a transparent electrode for electrochromic displays (ECDs). The electrochromic (EC) response of the dye-modified ITO porous electrode sintered at 150 °C, which exhibited a generally low resistivity, was markedly superior to that of a conventional dye-modified TiO 2 porous electrode sintered at the same temperature. Moreover, the EC characteristics of the dye-modified ITO porous electrode sintered at 150 °C were better than those of the high-temperature (450 °C) sintered conventional dye-modified TiO 2 porous electrode. These improvements in the EC characteristics of the dye-modified ITO porous electrode are attributed to its lower resistivity than that of the TiO 2 porous electrodes. In addition to its sufficiently low resistivity attained under the sintering conditions required for flexible ECD applications, the ITO porous film had superior visible-light transparency and dye adsorption capabilities. We conclude that the process temperature, resistivity, optical transmittance, and dye adsorption capability of the ITO porous electrode make it a promising transparent porous electrode for flexible ECD applications.

Black-to-Transmissive Electrochromism with Visible-to-Near-Infrared Switching of a Co(II)-Based Metallo-Supramolecular Polymer for Smart Window and Digital Signage Applications.

Science.gov (United States)

Hsu, Chih-Yu; Zhang, Jian; Sato, Takashi; Moriyama, Satoshi; Higuchi, Masayoshi

2015-08-26

Black-to-transmissive electrochromism has been obtained with a Co(II)-based metallo-supramolecular polymer (polyCo). Thin films of polyCo, based on bisterpyridine ligand assembled with Co(II) metal ion, were constructed by spray casting the polymer onto ITO glass. With such simple fabricating means to form good-quality films, polyCo films show stable switching at the central metal ion of the Co(II)/Co(I) redox reaction when immersed in aqueous solution. With an increase in the pH of the aqueous electrolyte solution from neutral, the film exhibits a color response due to the interaction between the d-orbital electron and hydroxide ions affecting the d-d* transition. As a result, a nearly transparent-to-black electrochromic performance can be achieved with a transmittance difference at 550 nm of 74.3% (81.9-7.6%) in pH 13 solution. The light absorption of the film can be tuned over light regions from visible to near-infrared with a large attenuation.

Electrochemical investigation of electrochromic devices based on NiO and WO3 films using different lithium salts electrolytes

International Nuclear Information System (INIS)

Wei, Youxiu; Chen, Mu; Liu, Weiming; Li, Lei; Yan, Yue

2017-01-01

Highlights: •ECDs based on NiO and WO 3 films using different electrolytes were fabricated. •Effect of different electrolytes on films and ECDs was investigated. •Applied voltage distribution on NiO and WO 3 electrodes in an ECD was studied. •Voltage distribution on films was unbalanced and associated with electrolyte. •Films have different impedance behavior in different states and electrolytes. -- Abstract: Electrochromic devices (ECDs) with different liquid electrolytes were fabricated using NiO film as counter electrode, WO 3 film as working electrode. The effect of liquid electrolytes containing different lithium salts (LiClO 4 , LiPF 6 , LiTFSI) on films and ECDs was investigated, such as transmittance change, charge density, memory effect and cyclic stability. Films or ECDs using LiPF 6 electrolyte have excellent electrochromic properties but low cyclic stability, compared with LiClO 4 and LiTFSI electrolytes. In order to deeply understand the effect of electrolyte on films and devices, the voltage distribution of films based on an analog cell and electrochemical impedance spectroscopy (EIS) were measured and analyzed in different lithium salts electrolytes. Results show that voltage distribution and EIS characteristics of films have obvious difference in liquid LiClO 4 , LiPF 6 and LiTFSI electrolytes. Voltage distribution on NiO and WO 3 films is unbalanced and the impedance of films in bleached and colored states is different in the same electrolyte.

Enhanced electrochromic properties of TiO2 nanoporous film prepared based on an assistance of polyethylene glycol

Science.gov (United States)

Xu, Shunjian; Luo, Xiaorui; Xiao, Zonghu; Luo, Yongping; Zhong, Wei; Ou, Hui; Li, Yinshuai

2017-01-01

Polyethylene glycol (PEG) was employed as pore-forming agent to prepare TiO2 nanoporous film based on spin-coating a TiO2 nanoparticle mixed paste on fluorine doped tin oxide (FTO) glass. The electrochromic and optical properties of the obtained TiO2 film were investigated by cyclic voltammetry (CV), chronoamperometry (CA) and UV-Vis spectrophotometer. The results show that the PEG in the mixed paste endows the TiO2 film with well-developed porous structure and improves the uniformity of the TiO2 film, which are helpful for the rapid intercalation and extraction of lithium ions within the TiO2 film and the strengthening of the diffuse reflection of visible light in the TiO2 film. As a result, the TiO2 film derived from the mixed paste with PEG displays higher electrochemical activity and more excellent electrochromic performances compared with the TiO2 film derived from the mixed paste without PEG. The switching times of coloration/bleaching are respectively 10.16/5.65 and 12.77/6.13 s for the TiO2 films with PEG and without PEG. The maximum value of the optical contrast of the TiO2 film with PEG is 21.2% while that of the optical contrast of the TiO2 film without PEG is 14.9%. Furthermore, the TiO2 film with PEG has better stability of the colored state than the TiO2 film without PEG.

Effect of post annealing treatment on electrochromic properties of spray deposited niobium oxide thin films

International Nuclear Information System (INIS)

Mujawar, S.H.; Inamdar, A.I.; Betty, C.A.; Ganesan, V.; Patil, P.S.

2007-01-01

Niobium oxide thin films were deposited on the glass and fluorine doped tin oxide (FTO) coated glass substrates using simple and inexpensive spray pyrolysis technique. During deposition of the films various process parameters like nozzle to substrate distance, spray rate, concentration of sprayed solution were optimized to obtain well adherent and transparent films. The films prepared were further annealed and effect of post annealing on the structural, morphological, optical and electrochromic properties was studied. Structural and morphological characterizations of the films were carried out using scanning electron microscopy, atomic force microscopy and X-ray diffraction techniques. Electrochemical properties of the niobium oxide thin films were studied by using cyclic-voltammetry, chronoamperometry and chronocoulometry

Thickness dependence of electro-optical properties of WO{sub 3} films as an electrochromic functional material for energy-efficient applications

Energy Technology Data Exchange (ETDEWEB)

Esmail, Ayat; Hashem, Hany; Soltan, Soltan; Hammam, Mahmoud; Ramadan, Ahmed [Faculty of Science, Department of Physics, Helwan University, Cairo (Egypt)

2017-01-15

WO{sub 3} films of different thicknesses (100, 200, and 300 nm) were prepared by two vacuum physical vapor deposition (PVD) methods (thermal evaporation and an electron gun). Electrophysical measurements (cyclic voltammetry and chronoamperometry) were carried out using a potentiostat in an electrochromic cell (liquid device) that consists of a substrate coated with double layers of F: SnO{sub 2} and WO{sub 3} served as working electrodes. X-ray diffraction showed an amorphous structure for all the deposited WO{sub 3} thin films. While the transmission in the bleached state does not change and it is close to the as-deposited state, it is slightly less at larger thickness. The cyclic voltammogram was more open (more current flow) for thicker films due to the less dense structure with many channels. Also, the coloration efficiency was higher at low thickness. The response time was of the order of seconds and decreased for coloration, while it increased for the bleaching process as the film thickness increases. According to the proposed figure of merit, the electrochromic performance deteriorates as the WO{sub 3} film thickness decreases. However, the thickness is more effective in the case of an electron gun. Generally, continuous films but thinner than 200 nm, are recommended for deposition methods. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Electrochromic nickel oxide films and their compatibility with potassium hydroxide and lithium perchlorate in propylene carbonate: Optical, electrochemical and stress-related properties

International Nuclear Information System (INIS)

Wen, Rui-Tao; Niklasson, Gunnar A.; Granqvist, Claes G.

2014-01-01

Porous nickel oxide films were deposited onto unheated indium tin oxide coated glass substrates by reactive dc magnetron sputtering. These films had a cubic NiO structure. Electrochromic properties were evaluated in 1 M potassium hydroxide (KOH) and in 1 M lithium perchlorate in propylene carbonate (Li–PC). Large optical modulation was obtained for ∼ 500-nm-thick films both in KOH and in Li–PC (∼ 70% and ∼ 50% at 550 nm, respectively). In KOH, tensile and compressive stresses, due to the expansion and contraction of the lattice, were found for films in their bleached and colored state, respectively. In Li–PC, compressive stress was seen both in colored and bleached films. Durability tests with voltage sweeps between − 0.5 and 0.65 V vs Ag/AgCl in KOH showed good durability for 10,000 cycles, whereas voltage sweeps between 2.0 and 4.7 V vs Li/Li + in Li–PC yielded significant degradation after 1000 cycles. - Highlights: • Ni oxide films were studied in KOH and in LiClO 4 + propylene carbonate (Li–PC). • Good electrochromism was found in both electrolytes. • In KOH, tensile/compressive stresses were seen in bleached/colored films. • In Li–PC, compressive stress was seen both in colored and bleached films

A poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid)/titanium oxide nanocomposite film synthesized by sol–gel assisted electropolymerization for electrochromic application

International Nuclear Information System (INIS)

Lu, Jinlin; Song, Hua; Li, Suning; Wang, Lin; Han, Lu; Ling, Han; Lu, Xuehong

2015-01-01

In this article, we report the facile synthesis of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid)/titanium dioxide (PEDOT:PSS/TiO 2 ) nanocomposite film by sol–gel assisted electropolymerization. The structure, morphology and composition of the films were investigated by different techniques, such as Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, atomic force microscope and X-ray photoelectron spectroscopy. The PEDOT:PSS/TiO 2 nanocomposite film was applied for electrochromic application. The results indicate that the PEDOT:PSS/TiO 2 nanocomposite film exhibits a higher optical contrast and a much better stability as compared to PEDOT:PSS film. The significant performance enhancement can be attributed to the nanoscale particle size and uniform size distribution of PEDOT:PSS/TiO 2 and the synergistic effect between the inorganic nano-TiO 2 and organic PEDOT:PSS material. - Highlights: • Facile synthesis of PEDOT:PSS/TiO 2 nanocomposite film by electropolymerization • PEDOT:PSS/TiO 2 film shows nano-scaled particle sizes and uniform size distribution. • PEDOT:PSS/TiO 2 film shows higher optical contrasts and faster switching speed. • PEDOT:PSS/TiO 2 film displays a good stability for electrochromic application

A poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid)/titanium oxide nanocomposite film synthesized by sol–gel assisted electropolymerization for electrochromic application

Energy Technology Data Exchange (ETDEWEB)

Lu, Jinlin, E-mail: jinlinlu@hotmail.com [School of Materials and Metallurgy, University of Science and Technology, Liaoning, Anshan 114051 (China); Song, Hua [School of Mechanical Engineering and Automation, University of Science and Technology, Liaoning, Anshan 114051 (China); Li, Suning; Wang, Lin; Han, Lu [School of Materials and Metallurgy, University of Science and Technology, Liaoning, Anshan 114051 (China); Ling, Han; Lu, Xuehong [School of Material Science and Engineering, Nanyang Technological University, 50 Nanyang Avenue, 639798 (Singapore)

2015-06-01

In this article, we report the facile synthesis of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonic acid)/titanium dioxide (PEDOT:PSS/TiO{sub 2}) nanocomposite film by sol–gel assisted electropolymerization. The structure, morphology and composition of the films were investigated by different techniques, such as Fourier transform infrared spectroscopy, X-ray diffraction, transmission electron microscopy, atomic force microscope and X-ray photoelectron spectroscopy. The PEDOT:PSS/TiO{sub 2} nanocomposite film was applied for electrochromic application. The results indicate that the PEDOT:PSS/TiO{sub 2} nanocomposite film exhibits a higher optical contrast and a much better stability as compared to PEDOT:PSS film. The significant performance enhancement can be attributed to the nanoscale particle size and uniform size distribution of PEDOT:PSS/TiO{sub 2} and the synergistic effect between the inorganic nano-TiO{sub 2} and organic PEDOT:PSS material. - Highlights: • Facile synthesis of PEDOT:PSS/TiO{sub 2} nanocomposite film by electropolymerization • PEDOT:PSS/TiO{sub 2} film shows nano-scaled particle sizes and uniform size distribution. • PEDOT:PSS/TiO{sub 2} film shows higher optical contrasts and faster switching speed. • PEDOT:PSS/TiO{sub 2} film displays a good stability for electrochromic application.

Applications of Poly(indole-6-carboxylic acid-co-2,2′-bithiophene Films in High-Contrast Electrochromic Devices

Directory of Open Access Journals (Sweden)

Chung-Wen Kuo

2018-03-01

Full Text Available Two homopolymers (poly(indole-6-carboxylic acid (PInc and poly(2,2′-bithiophene (PbT and a copolymer (poly(indole-6-carboxylic acid-co-2,2′-bithiophene (P(Inc-co-bT are electrodeposited on ITO electrode surfaces via electrochemical method. Electrochemical and electrochromic properties of PInc, PbT, and P(Inc-co-bT films were characterized using cyclic voltammetry and in situ UV-Vis spectroscopy. The anodic P(Inc-co-bT film prepared using Inc./bT = 1/1 feed molar ratio shows high optical contrast (30% at 890 nm and coloring efficiency (112 cm2 C−1 at 890 nm. P(Inc-co-bT film revealed light yellow, yellowish green, and bluish grey in the neutral, intermediate, and oxidation states, respectively. Electrochromic devices (ECDs were constructed using PInc, PbT, or P(Inc-co-bT film as anodic layer and PEDOT-PSS as cathodic layer. P(Inc-co-bT/PMMA-PC-ACN-LiClO4/PEDOT-PSS ECD showed high ∆T (31% at 650 nm, and PInc/PMMA-PC-ACN-LiClO4/PEDOT-PSS ECD displayed high coloration efficiency (416.7 cm2 C−1 at 650 nm. The optical memory investigations of PInc/PMMA-PC-ACN-LiClO4/PEDOT-PSS, PbT/PMMA-PC-ACN-LiClO4/PEDOT-PSS, and P(Inc-co-bT/PMMA-PC-ACN-LiClO4/PEDOT-PSS ECDs exhibited that ECDs had adequate optical memory in bleaching and coloring states.

Polyimide-polyether mixed conductors as switchable materials for electrochromic devices

Energy Technology Data Exchange (ETDEWEB)

Michot, C; Baril, D; Armand, M [Laboratoire d` Ionique et d` Electrochimie du Solide, ENSEEG, Institut National Polytechnique de Grenoble, Saint-Martin d` Heres (France)

1995-12-01

A new family of redox-active polymers have been obtained by polycondensation of {alpha},{omega}-diamino oligopolyethers with various aromatic tetracarboxylic acid anhydrides. The polyether blocks retain the usual cation co-ordination ability leading to solid-state ionic conduction while the relatively large electron affinity of the bis-imide moieties formed in the block polymers allows the reversible formation of stable radical anions ({sup -} and {sup 2-}) in the range 2-2.6 V vs. Li. Either slow-scan or microelectrode voltammetry indicate that the totality of the redox centres in such materials are readily accessible for all polyether spacer lengths tested (6-22 ether fragments), suggesting both a fast electron-exchange mechanism between anion radicals and a tendency for self assembly (stacking) of the planar aromatic groups. When increasing the number of atoms in the aromatic ring, the peak separation became smaller (benzene>naphthalene>perylene), resulting ultimately in simultaneous 2-electrons injection. These materials, due to the high coloration efficiency of the reduced state and their ready processability in thin films are excellent candidate for the realisation of laminated solid-state electrochromic devices

Chemically fabricated LiFePO{sub 4} thin film electrode for transparent batteries and electrochromic devices

Energy Technology Data Exchange (ETDEWEB)

Béléké, Alexis B. [Institut de recherche d’Hydro-Québec, 1800 Boul. Lionel-Boulet, Varennes, QC J3X 1S3 (Canada); Department of Mining and Materials Engineering, McGill University, M.H. Wong Building, 3610 rue University, Montréal, QC H3A 2B2 (Canada); Faure, Cyril [Institut de recherche d’Hydro-Québec, 1800 Boul. Lionel-Boulet, Varennes, QC J3X 1S3 (Canada); Röder, Manuel [Center for Applied Electrochemistry, Fraunhofer Institute for Silicate Research, Neunerplatz 2, 97083 Würzburg (Germany); Hovington, Pierre [Institut de recherche d’Hydro-Québec, 1800 Boul. Lionel-Boulet, Varennes, QC J3X 1S3 (Canada); Posset, Uwe [Center for Applied Electrochemistry, Fraunhofer Institute for Silicate Research, Neunerplatz 2, 97083 Würzburg (Germany); Guerfi, Abdelbast [Institut de recherche d’Hydro-Québec, 1800 Boul. Lionel-Boulet, Varennes, QC J3X 1S3 (Canada); Zaghib, Karim, E-mail: zaghib.karim@ireq.ca [Institut de recherche d’Hydro-Québec, 1800 Boul. Lionel-Boulet, Varennes, QC J3X 1S3 (Canada)

2016-12-15

Graphical abstract: Simplified diagram of the novel sol-gel approach of preparation of colorless and transparent LiFePO{sub 4} thin film electrode. - Highlights: • Novel sol-gel synthesis of colorless LFP thin film electrode for transparent Li-ion battery. • High performance of the electrode at various current densities: 5, 10, 20, 50 and 100 μA/cm{sup 2}. • LFP nanoparticles exhibit an excellent electro-activity. • Colorless LFP thin film shows a transmittance above 80% versus FTO. • Higher transmittance of LFP electrode a potential candidate for electrochromic devices. - Abstract: We report a new sol-gel approach of synthesis of LiFePO{sub 4} (LFP) thin film and its application as cathode materials for transparent Li-ion battery in half-cell configuration. LFP thin films were obtained from an alcoholic colloidal suspension of iron acetylacetonate (Fe(AcAc){sub 3}) and aqueous lithium dihydrogen phosphate (LiH{sub 2}PO{sub 4}) deposited on fluorine tin oxide (FTO) glass substrate, followed by heating at 450 °C under nitrogen gas for 1 h. X-ray diffraction (XRD) confirmed that the LFP films have an orthorhombic crystal system with space group Pnma (62). Scanning electron microscopy (SEM) shows spherical LFP nanoparticles aggregates homogenously deposited all over the surface of FTO substrate containing 3-D open pores. The electrochemical behaviors of thin film vs Li/Li{sup +} cell were investigated by cyclic voltammetry and galvanostatic charge-discharge measurements. The cycle life was evaluated by running 1000 cycles of charge-discharge at a current density of 20 μA/cm{sup 2}. The transmission spectra reveal 85–90% of transparency versus FTO as reference, which makes it a potential candidate as a complementary electrode in electrochromic devices (ECDs).

Preparation of electrochromic thin films by transformation of manganese(II) carbonate

Science.gov (United States)

Stojkovikj, Sasho; Najdoski, Metodija; Koleva, Violeta; Demiri, Sani

2013-10-01

A new chemical bath method for deposition of manganese(II) carbonate thin film on electroconductive FTO glass substrates is designed. The homogeneous thin films with thickness in the range of 70 to 500 nm are deposited at about 98 °C from aqueous solution containing urea and MnCl2. The chemical process is based on a low temperature hydrolysis of the manganese complexes with urea. Three types of films are under consideration: as-deposited, annealed and electrochemically transformed thin films. The structure of the films is studied by XRD, IR and Raman spectroscopy. Electrochemical and optical properties are examined in eight different electrolytes (neutral and alkaline) and the best results are achieved in two component aqueous solution of 0.1 M KNO3 and 0.01 M KOH. It is established that the as-deposited MnCO3 film undergoes electrochemically transformation into birnessite-type manganese(IV) oxide films, which exhibit electrochromic color changes (from bright brown to pale yellow and vice versa) with 30% difference in the transmittance of the colored and bleached state at 400 nm.

Electrochromic nickel oxide films and their compatibility with potassium hydroxide and lithium perchlorate in propylene carbonate: Optical, electrochemical and stress-related properties

Energy Technology Data Exchange (ETDEWEB)

Wen, Rui-Tao, E-mail: Ruitao.Wen@angstrom.uu.se; Niklasson, Gunnar A.; Granqvist, Claes G.

2014-08-28

Porous nickel oxide films were deposited onto unheated indium tin oxide coated glass substrates by reactive dc magnetron sputtering. These films had a cubic NiO structure. Electrochromic properties were evaluated in 1 M potassium hydroxide (KOH) and in 1 M lithium perchlorate in propylene carbonate (Li–PC). Large optical modulation was obtained for ∼ 500-nm-thick films both in KOH and in Li–PC (∼ 70% and ∼ 50% at 550 nm, respectively). In KOH, tensile and compressive stresses, due to the expansion and contraction of the lattice, were found for films in their bleached and colored state, respectively. In Li–PC, compressive stress was seen both in colored and bleached films. Durability tests with voltage sweeps between − 0.5 and 0.65 V vs Ag/AgCl in KOH showed good durability for 10,000 cycles, whereas voltage sweeps between 2.0 and 4.7 V vs Li/Li{sup +} in Li–PC yielded significant degradation after 1000 cycles. - Highlights: • Ni oxide films were studied in KOH and in LiClO{sub 4} + propylene carbonate (Li–PC). • Good electrochromism was found in both electrolytes. • In KOH, tensile/compressive stresses were seen in bleached/colored films. • In Li–PC, compressive stress was seen both in colored and bleached films.

Effects of oxidation potential and retention time on electrochromic stability of poly (3-hexyl thiophene) films

Science.gov (United States)

Kim, Tae-Ho; Hyun Song, Seok; Kim, Hyo-Jae; Oh, Seong-Hyeon; Han, Song-Yi; Kim, Goung; Nah, Yoon-Chae

2018-06-01

Herein, we report the effects of applied voltage on the electrochromic (EC) stability of poly(3-hexylthiophene) (P3HT) films during EC reactions. The transmittance difference and cycling stability of these films were monitored to optimize the oxidation voltage, and their chemical compositions were analyzed by X-ray photoelectron spectroscopy after long-term electrochemical cycling. High oxidation voltages increased the color contrast of P3HT films but decreased their cycling stability due to facilitating chemical degradation. Furthermore, at an optimized oxidation voltage, the retention time during potential pulsing was adjusted utilizing the optical memory of P3HT, revealing that the decreased voltage application time reduced power consumption by 9.6% and enhanced EC stability without loss of color contrast.

Variable Emittance Electrochromics Using Ionic Electrolytes and Low Solar Absorptance Coatings

Science.gov (United States)

Chandrasekhar, Prasanna

2011-01-01

One of the last remaining technical hurdles with variable emittance devices or skins based on conducting polymer electrochromics is the high solar absorptance of their top surfaces. This high solar absorptance causes overheating of the skin when facing the Sun in space. Existing technologies such as mechanical louvers or loop heat pipes are virtually inapplicable to micro (solar absorption to Alpha(s) of between 0.30 and 0.46. Coupled with the emittance properties of the variable emittance skins, this lowers the surface temperature of the skins facing the Sun to between 30 and 60 C, which is much lower than previous results of 100 C, and is well within acceptable satellite operations ranges. The performance of this technology is better than that of current new technologies such as microelectromechanical systems (MEMS), electrostatics, and electrophoretics, especially in applications involving micro and nano spacecraft. The coatings are deposited inside a high vacuum, layering multiple coatings onto the top surfaces of variable emittance skins. They are completely transparent in the entire relevant infrared region (about 2 to 45 microns), but highly reflective in the visible-NIR (near infrared) region of relevance to solar absorptance.

High optical and switching performance electrochromic devices based on a zinc oxide nanowire with poly(methyl methacrylate) gel electrolytes

Energy Technology Data Exchange (ETDEWEB)

Chun, Young Tea; Chu, Daping, E-mail: dpc31@cam.ac.uk [Electrical Engineering Division, Department of Engineering, University of Cambridge, 9 JJ Thomson Avenue, Cambridge CB3 0FA (United Kingdom); Neeves, Matthew; Placido, Frank [Thin Film Centre, University of the West of Scotland, Paisley PA1 2BE (United Kingdom); Smithwick, Quinn [Disney Research, 521 Circle Seven Drive, Glendale, Los Angeles, California 91201 (United States)

2014-11-10

High performance electrochromic devices have been fabricated and demonstrated utilizing a solid polymer electrolyte and zinc oxide (ZnO) nanowire (NW) array counter electrode. The poly(methyl methacrylate) based polymer electrolyte was spin coated upon hydrothermally grown ZnO NW array counter electrodes, while electron beam evaporated NiO{sub x} thin films formed the working electrodes. Excellent optical contrast and switching speeds were observed in the fabricated devices with active areas of 2 cm{sup 2}, exhibiting an optical contrast of 73.11% at the wavelength of 470 nm, combined with a fast switching time of 0.2 s and 0.4 s for bleaching and coloration, respectively.

High optical and switching performance electrochromic devices based on a zinc oxide nanowire with poly(methyl methacrylate) gel electrolytes

International Nuclear Information System (INIS)

Chun, Young Tea; Chu, Daping; Neeves, Matthew; Placido, Frank; Smithwick, Quinn

2014-01-01

High performance electrochromic devices have been fabricated and demonstrated utilizing a solid polymer electrolyte and zinc oxide (ZnO) nanowire (NW) array counter electrode. The poly(methyl methacrylate) based polymer electrolyte was spin coated upon hydrothermally grown ZnO NW array counter electrodes, while electron beam evaporated NiO x thin films formed the working electrodes. Excellent optical contrast and switching speeds were observed in the fabricated devices with active areas of 2 cm 2 , exhibiting an optical contrast of 73.11% at the wavelength of 470 nm, combined with a fast switching time of 0.2 s and 0.4 s for bleaching and coloration, respectively

Electrochromic behavior of poly(3,5-bis(4-bromophenyl)dithieno[3,2-b;2',3'-d]thiophene)

International Nuclear Information System (INIS)

Osken, Ipek; Bildirir, Hakan; Ozturk, Turan

2011-01-01

Electropolymerization of 3,5-bis(4-bromophenyl)dithieno[3,2-b;2',3'-d]thiophene, having a mild electron-withdrawing bromine atom attached to the para position of the two phenyl groups of dithienothiophene, was performed, utilizing a potentiodynamic method. The resultant homopolymer was characterized by cyclic volyammetry, fourier transform infrared and ultraviolet-visible spectroscopy. Spectroelectrochemical and electrochromic properties were investigated and a device was constructed with polyethylenedioxythiophene to understand the characteristics in detail, which had the potential range of 0.0-2.0 V for operating the device between green and blue colors. It had a good optical contrast of 18% with a switching time of less than a second. Moreover, open circuit memory and stability of the device were investigated.

Effect of Post-annealing on the Electrochromic Properties of Layer-by-Layer Arrangement FTO-WO3-Ag-WO3-Ag

Science.gov (United States)

Hoseinzadeh, S.; Ghasemiasl, R.; Bahari, A.; Ramezani, A. H.

2018-03-01

In the current study, composites of tungsten trioxide (W03) and silver (Ag) are deposited in a layer-by-layer electrochromic (EC) arrangement onto a fluorine-doped tin oxide coated glass substrate. Tungsten oxide nanoparticles are an n-type semiconductor that can be used as EC cathode material. Nano-sized silver is a metal that can serve as an electron trap center that facilitates charge departure. In this method, the WO3 and Ag nanoparticle powder were deposited by physical vapor deposition onto the glass substrate. The fabricated electrochromic devices (ECD) were post-annealed to examine the effect of temperature on their EC properties. The morphology of the thin film was characterized by scanning electron microscopy and atomic force microscopy. Structural analysis showed that the addition of silver dopant increased the size of the aggregation of the film. The film had an average approximate roughness of about 17.8 nm. The electro-optical properties of the thin film were investigated using cyclic voltammetry and UV-visible spectroscopy to compare the effects of different post-annealing temperatures. The ECD showed that annealing at 200°C provided better conductivity (maximum current of about 90 mA in the oxidation state) and change of transmittance (ΔT = 90% at the continuous switching step) than did the other thin films. The optical band gaps of the thin film showed that it allowed direct transition at 3.85 eV. The EC properties of these combinations of coloration efficiency and response time indicate that the WO3-Ag-WO3-Ag arrangement is a promising candidate for use in such ECDs.

The Effect of Ar/O2 Ratio on Electrochromic Response Time of Ni Oxides Grown Using an RF Sputtering System

Science.gov (United States)

Ahn, Kwang-Soon; Nah, Yoon-Chae; Yum, Jun-Ho; Sung, Yung-Eun

2002-02-01

The effect of Ar:O2 ratio on the electrochromic properties and the response time of NiO grown by RF sputtering were investigated by in situ transmittance measurements with continuous potential cycling and pulse potential cycling. The transmittance difference, coloration efficiency, memory effect, and cycling stability were all found to be independent of the Ar:O2 ratio. However, the transmittance of the as-deposited NiO as well as the response time were significantly affected. This may be attributed to the excess of oxygen occupied interstitial sites in the sputtered NiO that could result in the generation of Ni3+ ions and interference with proton intercalation/deintercalation.

Electrochromic properties of multicolored novel polymer synthesized via combination of benzotriazole and N-functionalized 2,5-di(2-thienyl)-1H-pyrrole units

International Nuclear Information System (INIS)

Rende, Eda; Kilic, Cihan E.; Udum, Yasemin Arslan; Toffoli, Daniele; Toppare, Levent

2014-01-01

Synthesis of new conducting polymers is desired since their electrochemical and optical properties enable them to be used as active layers in many device applications. Benzotriazole and N-functionalized 2,5-di(2-thienyl)-1H-pyrrole (SNS Series) containing polymers showed very promising results as electrochromic materials. In order to observe the effect of the combination of these two units, three new monomers; 2-(6-(2,5-bis(5-methylthiophen-2-yl)-1H-pyrrol-1-yl)hexyl)-4,7-di (thiophen-2-yl)-2H benzo[d][1,2,3]triazole (M1), 2-(6-(2,5-di(thiophen-2-yl)-1H-pyrrol-1-yl)hexyl)-4,7-di(thiophen-2-yl) -2H-benzo[d][1,2,3]triazole (M2) and 2-(6-(2,5-di(thiophen-2-yl)-1H-pyrrol-1-yl)hexyl)-4,7-bis (5-methylthiophen-2-yl)-2H-benzo[d][1,2,3]triazole (M3) were synthesized. To better characterize the electronic and spectroscopic properties of the monomers, density functional theory (DFT) and its time-dependent generalization (TD-DFT) were used to calculate their vertical ionization potentials, vertical electron affinity and to simulate and interpret their infrared and UV-vis spectra. The monomers were electrochemically polymerized and the resultant polymers were characterized with cyclic voltammetry and UV-vis-NIR spectroscopy techniques. An electrochromic device was constructed with electrochemical polymer of M2. The device switched between red and blue colors and showed exceptional optical memory

Low-cost, highly transparent flexible low-e coating film to enable electrochromic windows with increased energy savings

Energy Technology Data Exchange (ETDEWEB)

Berland, Brian [ITN Energy Systems, Inc., Littleton, CO (United States); Hollingsworth, Russell [ITN Energy Systems, Inc., Littleton, CO (United States)

2015-03-31

Five Quads of energy are lost through windows annually in the U.S. Low-e coatings are increasingly employed to reduce the wasted energy. Most commonly, the low-e coating is an oxide material applied directly to the glass at high temperature. With over 100,000,000 existing homes, a retrofit product is crucial to achieve widespread energy savings. Low-e films, i.e. coatings on polymeric substrates, are now also available to meet this need. However, the traditional oxide materials and process is incompatible with low temperature plastics. Alternate high performing low-e films typically incorporate materials that limit visible transmission to 35% or less. Further, the cost is high. The objective of this award was to develop a retrofit, integrated low-e/electrochromic window film to dramatically reduce energy lost through windows. While field testing of state-of-the-art electrochromic (EC) windows show the energy savings are maximized if a low-e coating is used in conjunction with the EC, available low-e films have a low visible transmission (~70% or less) that limits the achievable clear state and therefore, appearance and energy savings potential. Comprehensive energy savings models were completed at Lawrence Berkeley National Lab (LBNL). A parametric approach was used to project energy usage for windows with a large range of low-e properties across all U.S. climate zones, without limiting the study to materials that had already been produced commercially or made in a lab. The model enables projection of energy savings for low-e films as well as integrated low-e/EC products. This project developed a novel low-e film, optimized for compatibility with EC windows, using low temperature, high deposition rate processes for the growth of low-e coatings on plastic films by microwave plasma enhanced chemical vapor deposition. Silica films with good density and optical properties were demonstrated at deposition rates as high as 130Å/sec. A simple bi-layer low-e stack of

Roll-to-Roll Production of Transparent Silver-Nanofiber-Network Electrodes for Flexible Electrochromic Smart Windows.

Science.gov (United States)

Lin, Sen; Bai, Xiaopeng; Wang, Haiyang; Wang, Haolun; Song, Jianan; Huang, Kai; Wang, Chang; Wang, Ning; Li, Bo; Lei, Ming; Wu, Hui

2017-11-01

Electrochromic smart windows (ECSWs) are considered as the most promising alternative to traditional dimming devices. However, the electrode technology in ECSWs remains stagnant, wherein inflexible indium tin oxide and fluorine-doped tin oxide are the main materials being used. Although various complicated production methods, such as high-temperature calcination and sputtering, have been reported, the mass production of flexible and transparent electrodes remains challenging. Here, a nonheated roll-to-roll process is developed for the continuous production of flexible, extralarge, and transparent silver nanofiber (AgNF) network electrodes. The optical and mechanical properties, as well as the electrical conductivity of these products (i.e., 12 Ω sq -1 at 95% transmittance) are comparable with those AgNF networks produced via high-temperature sintering. Moreover, the as-prepared AgNF network is successfully assembled into an A4-sized ECSW with short switching time, good coloration efficiency, and flexibility. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Electrospun poly(vinylidene fluoride) copolymer/octahydroxy-polyhedral oligomeric silsesquioxane nanofibrous mats as ionic liquid host: enhanced salt dissociation and its function in electrochromic device

International Nuclear Information System (INIS)

Zhou, Rui; Pramoda, Kumari Pallathadka; Liu, Wanshuang; Zhou, Dan; Ding, Guoqiang; He, Chaobin; Leong, Yew Wei; Lu, Xuehong

2014-01-01

Highlights: • The well dispersed POSS-OH promotes the dissociation of both LiClO 4 and BMIM + BF 4 − . • POSS-OH significantly increases the ionic conductivity and lithium transference number. • POSS-OH containing electrolyte improves the optical contrast of electrochromic device. - Abstract: Electrospun polymer nanofibrous mats loaded with ionic liquids (ILs) and lithium salts are promising non-volatile electrolytes owing to their high ionic conductivities. However, the large cations of ILs are difficult to diffuse into solid electrodes, whereas the lithium ions in ILs tend to form anionic complexes with the IL anions, reducing the number of free lithium ions. To address these issues, octa(3-hydroxy-3-methylbutyldimethylsiloxy) polyhedral oligomeric silsesquioxane (POSS-OH), which has large specific surface area and functionality number, is incorporated into electrospun poly(vinylidene fluoride-co-hexafluoropropylene) (PVDF-co-HFP) nanofibrous mats, and the mats are used to host LiClO 4 /1-butyl-3-methylimidazolium tetrafluoroborate (BMIM + BF 4 − ). It is found that POSS-OH can significantly increase both ionic conductivity and lithium transference number of the electrolytes owing to the Lewis acid-base interactions of POSS-OH with ClO 4 − and BF 4 − . The electrochromic device using the hybrid mat (with 5 wt% POSS-OH) loaded with LiClO 4 /BMIM + BF 4 − as the electrolyte shows significantly improved transmittance contrast and switching time, as a result of increased number of free lithium ions

TiO2 nanowires for potential facile integration of solar cells and electrochromic devices

International Nuclear Information System (INIS)

Qiang, Pengfei; Chen, Zhongwei; Yang, Peihua; Liu, Pengyi; Mai, Wenjie; Cai, Xiang; Tan, Shaozao

2013-01-01

Self-powered systems usually consist of energy-acquisition components, energy-storage components and functional components. The development of nanoscience and nanotechnology has greatly improved the performance of all the components of self-powered systems. However, huge differences in the materials and configurations in the components cause large difficulties for integration and miniaturization of self-powered systems. Design and fabrication of different components in a self-powered system with the same or similar materials/configurations should be able to make the above goal easier. In this work, a proof-of-concept experiment involving an integrated self-powered color-changing system consisting of TiO 2 nanowire based sandwich dye-sensitized solar cells (DSSCs) and electrochromic devices (ECDs) is designed and demonstrated. When sunlight illuminates the entire system, the DSSCs generate electrical power and turn the ECD to a darker color, dimming the light; by switching the connection polarity of the DSSCs, the lighter color can be regained, implying the potential application of this self-powered color-changing system for next generation sun glasses and smart windows. (paper)

Synthesis of electrochromic vanadium oxide by pulsed spray pyrolysis technique and its properties

International Nuclear Information System (INIS)

Patil, C E; Tarwal, N L; Shinde, P S; Patil, P S; Deshmukh, H P

2009-01-01

A new improved pulsed spray pyrolysis technique (PSPT) was employed to deposit a vanadium oxide (V 2 O 5 ) thin film from a methanolic vanadium chloride precursor onto glass and conducting F : SnO 2 coated glass substrates. The structural, morphological, electrical, optical and spectroscopic properties of the film deposited at 573 K were studied. Infrared spectroscopy and x-ray diffraction confirmed the presence of the V 2 O 5 phase. The V 2 O 5 film (thickness ∼118 nm) is polycrystalline with a tetragonal crystal structure. Scanning electron microscopy reveals compact granular morphology consisting of ∼80-100 nm size grains. The film is transparent in the visible region (average %T ∼70%) with an optical band gap energy of 2.47 eV involving both direct and indirect optical transitions. The room temperature electrical resistivity (conductivity) of the film is 1.6 x 10 8 Ω cm (6.25 x 10 -9 S cm -1 ) with an activation energy of 0.67 eV in the temperature range 300-550 K. It exhibited cathodic electrochromism in the lithium containing electrolyte (0.5 M LiClO 4 + propylene carbonate).

Pairing of near-ultraviolet solar cells with electrochromic windows for smart management of the solar spectrum

Science.gov (United States)

Davy, Nicholas C.; Sezen-Edmonds, Melda; Gao, Jia; Lin, Xin; Liu, Amy; Yao, Nan; Kahn, Antoine; Loo, Yueh-Lin

2017-08-01

Current smart window technologies offer dynamic control of the optical transmission of the visible and near-infrared portions of the solar spectrum to reduce lighting, heating and cooling needs in buildings and to improve occupant comfort. Solar cells harvesting near-ultraviolet photons could satisfy the unmet need of powering such smart windows over the same spatial footprint without competing for visible or infrared photons, and without the same aesthetic and design constraints. Here, we report organic single-junction solar cells that selectively harvest near-ultraviolet photons, produce open-circuit voltages eclipsing 1.6 V and exhibit scalability in power generation, with active layers (10 cm2) substantially larger than those typical of demonstration organic solar cells (0.04-0.2 cm2). Integration of these solar cells with a low-cost, polymer-based electrochromic window enables intelligent management of the solar spectrum, with near-ultraviolet photons powering the regulation of visible and near-infrared photons for natural lighting and heating purposes.

Fabrication of transparent conductive tri-composite film for electrochromic application

Science.gov (United States)

Choi, Dahyun; Lee, Minji; Kim, Hyungsub; Chu, Won-shik; Chun, Doo-man; Ahn, Sung-Hoon; Lee, Caroline Sunyong

2017-12-01

A transparent conductive electrode (TCE) based on poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS) was developed using a dry deposition method for application as an electrochromic (EC) device. To improve its electrical conductivity and stable EC performance, AgNW and TiO2 nanoparticles were included in the TCE film. The resulting TiO2/AgNW/PEDOT:PSS hybrid film showed electrical sheet resistivity of 23 Ω/sq., similar to that of a commercial TCE film. When +2.0 V was applied to the hybrid film, the response current was stable, maintaining a value of 2.0 mA. We found that the hybrid film could be used as an EC device, without using commercial TCE film. Antimony-doped tin oxide on indium-doped tin oxide-glass as an ion-storage layer was combined with the hybrid film, with 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide (EMIM-TFSI) injected into the EC device as an ionic liquid electrolyte. The optical transmittance difference between the colored and bleached states was 23% at 630 nm; under applied voltages of -2.0 V and +2.0 V, the coloration efficiency was 127.83 cm2/C. Moreover, cyclic transmittance with switching voltage for 3 h showed stable optical transmittance of 31% at 630 nm. Cyclic voltammetry measurements indicated stable behavior over 50 cycles. Thus, the proposed TCE configuration (TiO2/AgNW/PEDOT:PSS) shows great potential as a substitute for commercial TCEs, the cost of which depends on the availability of rare-earth materials.

Stretchable and Hydrophobic Electrochromic Devices Using Wrinkled Graphene and PEDOT:PSS

Directory of Open Access Journals (Sweden)

Srinivasa Kartik Nemani

2018-01-01

Full Text Available We present an electrochromic device (ECD fabricated using PEDOT:PSS and graphene as active conductive electrode films and a flexible compliant polyurethane substrate with 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonylimide (EMI-TSFI additive, as ionic medium. This device with a docile, elastic intermediate substrate along with a transparency controlled PEDOT:PSS film provides a wide color contrast and fast switching rate. We harness wrinkling instability of graphene to achieve a hydrophobic nature without compromising transparency of the ECD. This mechanical self-assembly approach helps in controlling the wavelength of wrinkles generated by inducing measured prestrain conditions and regulating the modulus contrast by selection of underlying materials used, hereby controlling the extent of transparency. The reduction and oxidation switching times for the device were analyzed to be 5.76 s and 5.34 s for a 90% transmittance change at an operating DC voltage of 15 ± 0.1 V. Strain dependent studies show that the performance was robust with the device retaining switching contrasts even at 15% uniaxial strain conditions. Our device also exhibits superior antiwetting properties with an average water contact angle of 110°  ± 2° at an induced radial prestrain of 30% in the graphene film. A wide range color contrast, flexibility, and antiwetting nature of the device envision its uses in smart windows, visors, and other wearable equipment where these functionalities are of outmost importance for developing new generation of smart interactive devices.

Ionically conducting Er3+-doped DNA-based biomembranes for electrochromic devices

International Nuclear Information System (INIS)

Leones, R.; Fernandes, M.; Sentanin, F.; Cesarino, I.; Lima, J.F.; Zea Bermudez, V. de; Pawlicka, A.; Magon, C.J.; Donoso, J.P.; Silva, M.M.

2014-01-01

Biopolymer-based membranes have particular interest due to their biocompatibility, Biodegradability, easy extraction from natural resources and low cost. The incorporation of Er 3+ ions into natural macromolecule hosts with the purpose of producing highly efficient emitting phosphors is of widespread interest in materials science, due to their important roles in display devices. Thus, biomembranes may be viewed as innovative materials for the area of optics. This paper describes studies of luminescent material DNA-based membranes doped with erbium triflate and demonstrates that their potential technological applications may be expanded to electrochromic devices. The sample that exhibits the highest ionic conductivity is DNA 10 Er, (1.17 × 10 −5 and 7.76 × 10 −4 S.cm −1 at 30 and 100 °C, respectively). DSC, XRD and POM showed that the inclusion of the guest salt into DNA does not change significantly its amorphous nature. The overall redox stability was ca. 2.0 V indicating that these materials have an acceptable stability window for applications in solid state electrochemical devices. The EPR analysis suggested that the Er 3+ ions are distributed in various environments. A small ECD comprising a Er 3+ -doped DNA-based membrane was assembled and tested by cyclic voltammetry and chronoamperometry. These electrochemical analyses revealed a pale blue color to transparent color change and a decrease of the charge density from -4.0 to -1.2 mC.cm −2 during 4000 color/bleaching cycles

Microstructure, optical, and electrochromic properties of sol-gel nanoporous tungsten oxide films

Science.gov (United States)

Djaoued, Yahia; Ashrit, P. V.; Badilescu, S.; Bruning, R.

2003-08-01

Porous tungsten oxide films have been prepared by a nonhydrolitic sol-gel method using poly(ethylene glycol) (PEG) as a structure directing agent. The method entails the hydrolysis of an ethanolic solution of tungsten ethoxide (formed by the reaction of WCl6 with ethanol) followed by condensation and polymerization at the PEG-tungsten oxide oligometers interface. A highly porous WO3 framework was obtained after PEG was burned off by calcination at a relativley low temperature. AFM images of the films treated thermally show an ordered material rather than microscopic particulates. Both fibrilar nanostructures and striped phase can be obtained via this approach, depending on the concentration of PEG in the coating solution. XRD data from the fibrils indicate that they are crystalline with very small crystals, whereas the striped phases obtained with 20% PEG correspond to two crystalline phases, one, the stoichiometric WO3 and the other one an oxygen deficient phase, containing larger crystals (~28 nm). The results show that PEG promotes the formation of oxygen deficient phases and delays crystallization. Compared to WO3 with no PEG, the optical and electrochromic properties of the macroporous tungsten oxide films appear to be significantly improved. The formation of organized nanostructures is tentatively accounted for by the strong hydrogen bonding interactions between PEG and the tungsten oxide oligomers.

Transparent Wood Smart Windows: Polymer Electrochromic Devices Based on Poly(3,4-Ethylenedioxythiophene):Poly(Styrene Sulfonate) Electrodes.

Science.gov (United States)

Lang, Augustus W; Li, Yuanyuan; De Keersmaecker, Michel; Shen, D Eric; Österholm, Anna M; Berglund, Lars; Reynolds, John R

2018-03-09

Transparent wood composites, with their high strength and toughness, thermal insulation, and excellent transmissivity, offer a route to replace glass for diffusely transmitting windows. Here, conjugated-polymer-based electrochromic devices (ECDs) that switch on-demand are demonstrated using transparent wood coated with poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) (PEDOT:PSS) as a transparent conducting electrode. These ECDs exhibit a vibrant magenta-to-clear color change that results from a remarkably colorless bleached state. Furthermore, they require low energy and power inputs of 3 mWh m -2 at 2 W m -2 to switch due to a high coloration efficiency (590 cm 2  C -1 ) and low driving voltage (0.8 V). Each device component is processed with high-throughput methods, which highlights the opportunity to apply this approach to fabricate mechanically robust, energy-efficient smart windows on a large scale. © 2018 The Authors. Published by Wiley-VCH Verlag GmbH & Co. KGaA.

Synthesis of Dimethyl-Substituted Polyviologen and Control of Charge Transport in Electrodes for High-Resolution Electrochromic Displays

Directory of Open Access Journals (Sweden)

Kan Sato

2017-03-01

Full Text Available Electrochromic (EC polymers such as polyviologens have been attracting considerable attention as wet-processable electrodes for EC displays, thanks to their brilliant color change accompanied with reversible redox reactions. To establish wider usage, achieving multicolor and high-resolution characteristics is indispensable. In this paper, we demonstrated that the introduction of substituents such as methyl groups into bipyridine units changed the stereostructure of the cation radicals, and thus shifted the color (e.g., ordinary purple to blue. Also, by relaxing excessive π-stacking between the viologen moieties, the response rate was improved by a factor of more than 10. The controlled charge transport throughout the polyviologen layer gave rise to the fabrication of EC displays which are potentially suitable for the thin film transistor (TFT substrate as the counter electrodes with submillimeter pixels. The findings can be versatilely used for the new design of polyviologens with enhanced electrochemical properties and high-resolution, multicolor EC displays.

Optimization of PEDOT films in ionic liquid supercapacitors: demonstration as a power source for polymer electrochromic devices.

Science.gov (United States)

Österholm, Anna M; Shen, D Eric; Dyer, Aubrey L; Reynolds, John R

2013-12-26

We report on the optimization of the capacitive behavior of poly(3,4-ethylenedioxythiophene) (PEDOT) films as polymeric electrodes in flexible, Type I electrochemical supercapacitors (ESCs) utilizing ionic liquid (IL) and organic gel electrolytes. The device performance was assessed based on figures of merit that are critical to evaluating the practical utility of electroactive polymer ESCs. PEDOT/IL devices were found to be highly stable over hundreds of thousands of cycles and could be reversibly charged/discharged at scan rates between 500 mV/s and 2 V/s depending on the polymer loading. Furthermore, these devices exhibit leakage currents and self-discharge rates that are comparable to state of the art electrochemical double-layer ESCs. Using an IL as device electrolyte allowed an extension of the voltage window of Type I ESCs by 60%, resulting in a 2.5-fold increase in the energy density obtained. The efficacies of tjese PEDOT ESCs were assessed by using them as a power source for a high-contrast and fast-switching electrochromic device, demonstrating their applicability in small organic electronic-based devices.

Integration of graphene sensor with electrochromic device on modulus-gradient polymer for instantaneous strain visualization

Science.gov (United States)

Yang, Tingting; Zhong, Yujia; Tao, Dashuai; Li, Xinming; Zang, Xiaobei; Lin, Shuyuan; Jiang, Xin; Li, Zhihong; Zhu, Hongwei

2017-09-01

In nature, some animals change their deceptive coloration for camouflage, temperature preservation or communication. This astonishing function has inspired scientists to replicate the color changing abilities of animals with artificial skin. Recently, some studies have focused on the smart materials and devices with reversible color changing or light-emitting properties for instantaneous strain visualization. However, most of these works only show eye-detectable appearance change when subjected to large mechanical deformation (100%-500% strain), and conspicuous color change at small strain remains rarely explored. In the present study, we developed a user-interactive electronic skin with human-readable optical output by assembling a highly sensitive resistive strain sensor with a stretchable organic electrochromic device (ECD) together. We explored the substrate effect on the electromechanical behavior of graphene and designed a strategy of modulus-gradient structure to employ graphene as both the highly sensitive strain sensing element and the insensitive stretchable electrode of the ECD layer. Subtle strain (0-10%) was enough to evoke an obvious color change, and the RGB value of the color quantified the magnitude of the applied strain. Such high sensitivity to smaller strains (0-10%) with color changing capability will potentially enhance the function of wearable devices, robots and prosthetics in the future.

Mesoporous amorphous tungsten oxide electrochromic films: a Raman analysis of their good switching behavior

International Nuclear Information System (INIS)

Chatzikyriakou, Dafni; Krins, Natacha; Gilbert, Bernard; Colson, Pierre; Dewalque, Jennifer; Denayer, Jessica; Cloots, Rudi; Henrist, Catherine

2014-01-01

Graphical abstract: - Highlights: • Mesoporous films exhibit better electrochemical kinetics compared to the dense films. • Mesoporous films exhibit better reversibility compared to the dense films. • Li + cations disrupt WO 3 network in a reversible way in the mesoporous film. • Li + irreversibly intercalate in the voids of crystallites in the dense film. - Abstract: The intercalation and de-intercalation of lithium cations in electrochromic tungsten oxide thin films are significantly influenced by their structural and surface characteristics. In this study, we prepared two types of amorphous films via the sol-gel technique: one dense and one mesoporous in order to compare their response upon lithium intercalation and de-intercalation. According to chronoamperometric measurements, Li + intercalates/de-intercalates faster in the mesoporous film (24s/6s) than in the dense film (48s/10s). The electrochemical measurements (cyclic voltammetry and chronoamperometry) also showed worse reversibility for the dense film compared to the mesoporous film, giving rise to important Li + trapping and remaining coloration of the film. Raman analysis showed that the mesoporous film provides more accessible and various W-O surface bonds for Li + intercalation. On the contrary, in the first electrochemical insertion and de-insertion in the dense film, Li + selectively reacts with a few surface W-O bonds and preferentially intercalates into pre-existing crystallites to form stable irreversible Li x WO 3 bronze

A Resettable Keypad Lock with Visible Readout Based on Closed Bipolar Electrochemistry and Electrochromic Poly(3-methylthiophene) Films.

Science.gov (United States)

Wang, Lei; Lian, Wenjing; Liu, Hongyun

2016-03-24

A closed bipolar electrode (BPE) system was developed with electrochromic poly(3-methylthiophene) (PMT) films electropolymerized on the ITO/rGO electrode as one pole of BPE in the reporting reservoir and the bare ITO electrode as another pole of BPE in the analyte reservoir, in which rGO represents reduced graphene oxide. Under a suitable driving voltage (Vtot), the electrochemical reduction/oxidation of electroactive probes, such as H2O2/glutathione (Glu), in the analyte reservoir could induce the reversible color change of PMT films in the reporting reservoir between blue and red. Based on this, a keypad lock with H2O2 , Glu, and Vtot =-3.0 V as the three inputs and the color change of PMT films as the visible output was established. This system was easily operated and did not need to synthesize the complex compounds or DNA molecules. The security system was easy to reset and could be used repeatedly. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Optical materials technology for energy efficiency and solar energy conversion XI: Chromogenics for smart windows; Proceedings of the Meeting, Toulouse, France, May 19, 21, 1992

International Nuclear Information System (INIS)

Hugot-le Goff, A.; Granqvist, C.G.; Lampert, C.M.

1992-01-01

The present conference discusses electrochromic tungsten oxide and nickel oxide films, electrochromic smart window devices, and thermochromic and variable light-scattering materials. Attention is given to the structural and physical properties of WO3 films prepared by CVD, the degradation of electrochromic amorphous WO3 films after coloration, the electrochromic mechanism of RF diode-sputtered nickel oxide films, and the optical and electrochemical properties of CeO2 and CeO2-TiO2 coatings. Also discussed are new solid electrolytes for electrochromic smart windows, electrochromic glazing, a smart window using a proton-conducting polymer as an electrolyte, and the electrochromism of colloidal WO3 and IrO2

A new repeatable, optical writing and electrical erasing device based on photochromism and electrochromism of viologen

International Nuclear Information System (INIS)

Gao, Li-ping; Wei, Jian; Wang, Yue-chuan; Ding, Guo-jing; Yang, Yu-lin

2012-01-01

New optical writing and electrical erasing devices have been successfully fabricated that exploit the photochromism and electrochromism of viologen. In a preliminary study, both the structures of viologen and device were investigated in detail by UV–vis spectra in order to confirm their effects on the optical writing and electrical erasing performances of corresponding devices. For sandwiched, single and complementary devices based on benzyl viologen (BV 2+ ), only optical writing can be performed, not electrical erasing operations, which indicated these devices cannot realize optical information rewriting. For single and complementary devices based on styrene-functional viologen (V BV 2+ ) and acrylic-functional viologen (ACV 2+ ), optical writing and electrical erasing operations can be reversibly performed and optical information rewriting realized. It is clear that single devices based on V BV 2+ and ACV 2+ possess better performance accompanied with contrast without significant degradation and bleaching times and without significant deterioration over 10 repeated writing/erasing cycles. Furthermore, we put forward possible mechanisms for sandwiched, single and complementary devices based on V BV 2+ and ACV 2+ for the optical writing and electrical erasing operations. This study provides a new strategy to design optical writing and electrical erasing devices to realize optical information rewriting. (paper)

The effect of water on the electrochromic properties of WO{sub 3} films prepared by vacuum and chemical methods

Energy Technology Data Exchange (ETDEWEB)

Leftheriotis, G.; Papaefthimiou, S.; Yianoulis, P. [Department of Physics, University of Patras, Patras 26500 (Greece)

2004-06-01

We present a comparative study on the effect of absorbed water on the properties of tungsten oxide films prepared by two different methods (e-gun evaporation, and an aqueous sol-gel technique). Scanning electron microscopy, Fourier transform infrared spectroscopy and electrochemical techniques have been used to assess the film properties. It has been found that the preparation method of the films greatly affects their water content and thus, electron gun evaporated films have less water incorporated into their structure than their sol-gel counterparts. The former are closely packed and transparent with most of their water content adsorbed on their surface, while the latter have a porous structure, being opaque, highly hydroxylated and hydrated to a lesser extent. Both types of films exhibit reversible electrochromism, with the evaporated films being stable up to 5000 coloration-bleaching cycles and the sol-gel ones gradually degrading after 1000 cycles. Irreversible Li{sup +} trapping related to the presence of water and hydroxyl radicals has been envisaged as the cause of the inferior cycling stability of the sol-gel films.

Roll-to-Roll sputtered ITO/Cu/ITO multilayer electrode for flexible, transparent thin film heaters and electrochromic applications.

Science.gov (United States)

Park, Sung-Hyun; Lee, Sang-Mok; Ko, Eun-Hye; Kim, Tae-Ho; Nah, Yoon-Chae; Lee, Sang-Jin; Lee, Jae Heung; Kim, Han-Ki

2016-09-22

We fabricate high-performance, flexible, transparent electrochromic (EC) films and thin film heaters (TFHs) on an ITO/Cu/ITO (ICI) multilayer electrode prepared by continuous roll-to-roll (RTR) sputtering of ITO and Cu targets. The RTR-sputtered ICI multilayer on a 700 mm wide PET substrate at room temperature exhibits a sheet resistance of 11.8 Ω/square and optical transmittance of 73.9%, which are acceptable for the fabrication of flexible and transparent EC films and TFHs. The effect of the Cu interlayer thickness on the electrical and optical properties of the ICI multilayer was investigated in detail. The bending and cycling fatigue tests demonstrate that the RTR-sputtered ICI multilayer was more flexible than a single ITO film because of high strain failure of the Cu interlayer. The flexible and transparent EC films and TFHs fabricated on the ICI electrode show better performances than reference EC films and TFHs with a single ITO electrode. Therefore, the RTR-sputtered ICI multilayer is the best substitute for the conventional ITO film electrode in order to realize flexible, transparent, cost-effective and large-area EC devices and TFHs that can be used as flexible and smart windows.

Characterization of dynamic thermal control schemes and heat transfer pathways for incorporating variable emissivity electrochromic materials into a space suit heat rejection system

Science.gov (United States)

Massina, Christopher James

The feasibility of conducting long duration human spaceflight missions is largely dependent on the provision of consumables such as oxygen, water, and food. In addition to meeting crew metabolic needs, water sublimation has long served as the primary heat rejection mechanism in space suits during extravehicular activity (EVA). During a single eight hour EVA, approximately 3.6 kg (8 lbm) of water is lost from the current suit. Reducing the amount of expended water during EVA is a long standing goal of space suit life support systems designers; but to date, no alternate thermal control mechanism has demonstrated the ability to completely eliminate the loss. One proposed concept is to convert the majority of a space suit's surface area into a radiator such that the local environment can be used as a radiative thermal sink for rejecting heat without mass loss. Due to natural variations in both internal (metabolic) loads and external (environmental) sink temperatures, radiative transport must be actively modulated in order to maintain an acceptable thermal balance. Here, variable emissivity electrochromic devices are examined as the primary mechanism for enabling variable heat rejection. This dissertation focuses on theoretical and empirical evaluations performed to determine the feasibility of using a full suit, variable emissivity radiator architecture for space suit thermal control. Operational envelopes are described that show where a given environment and/or metabolic load combination may or may not be supported by the evaluated thermal architecture. Key integration considerations and guidelines include determining allowable thermal environments, defining skin-to-radiator heat transfer properties, and evaluating required electrochromic performance properties. Analysis also considered the impacts of dynamic environmental changes and the architecture's extensibility to EVA on the Martian surface. At the conclusion of this work, the full suit, variable emissivity

Organic Synthetic Advanced Materials for Optoelectronic and Energy Applications (at National Taipei University of Technology)

Energy Technology Data Exchange (ETDEWEB)

Yen, Hung-Ju [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Chemistry Division

2016-11-14

These slides cover Hung-Ju Yen's recent work in the synthesis and structural design of functional materials, which were further used for optoelectronic and energy applications, such as lithium ion battery, solar cell, LED, electrochromic, and fuel cells. This was for a job interview at National Taipei University of Technology. The following topics are detailed: current challenges for lithium-ion batteries; graphene, graphene oxide and nanographene; nanographenes with various functional groups; fine tune d-spacing through organic synthesis: varying functional group; schematic view of LIBs; nanographenes as LIB anode; rate performance (charging-discharging); electrochromic technology; electrochromic materials; advantages of triphenylamine; requirement of electrochromic materials for practical applications; low driving voltage and long cycle life; increasing the electroactive sites by multi-step synthetic procedures; synthetic route to starburst triarylamine-based polyamide; electrochromism ranging from visible to NIR region; transmissive to black electrochromism; RGB and CMY electrochromism.

Organic Synthetic Advanced Materials for Optoelectronic and Energy Applications (at Center for Condensed Matter Sciences)

Energy Technology Data Exchange (ETDEWEB)

Yen, Hung-Ju [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Chemistry Division

2016-11-14

These slides cover Hung-Ju Yen's recent work in the synthesis and structural design of functional materials, which were further used for optoelectronic and energy applications, such as lithium ion battery, solar cell, LED, electrochromic, and fuel cells. This was for a job interview at Center for Condensed Matter Sciences. The following topics are detailed: current challenges for lithium-ion batteries; graphene, graphene oxide and nanographene; nanographenes with various functional groups; fine tune d-spacing through organic synthesis: varying functional group; schematic view of LIBs; nanographenes as LIB anode; rate performance (charging-discharging); electrochromic technology; electrochromic materials; advantages of triphenylamine; requirement of electrochromic materials for practical applications; low driving voltage and long cycle life; increasing the electroactive sites by multi-step synthetic procedures; synthetic route to starburst triarylamine-based polyamide; electrochromism ranging from visible to NIR region; transmissive to black electrochromism; RGB and CMY electrochromism.

Organic Synthetic Advanced Materials for Optoelectronic and Energy Applications (at National Sun Yat-sen University) 

Energy Technology Data Exchange (ETDEWEB)

Yen, Hung-Ju [Los Alamos National Lab. (LANL), Los Alamos, NM (United States). Chemistry Division

2016-11-14

These slides cover Hung-Ju Yen's recent work in the synthesis and structural design of functional materials, which were further used for optoelectronic and energy applications, such as lithium ion battery, solar cell, LED, electrochromic, and fuel cells. This was for a job interview at National Sun Yat-sen University. The following topics are detailed: current challenges for lithium-ion batteries; graphene, graphene oxide and nanographene; nanographenes with various functional groups; fine tune d-spacing through organic synthesis: varying functional group; schematic view of LIBs; nanographenes as LIB anode; rate performance (charging-discharging); electrochromic technology; electrochromic materials; advantages of triphenylamine; requirement of electrochromic materials for practical applications; low driving voltage and long cycle life; increasing the electroactive sites by multi-step synthetic procedures; synthetic route to starburst triarylamine-based polyamide; electrochromism ranging from visible to NIR region; transmissive to black electrochromism; RGB and CMY electrochromism.

Statistical mixture design and multivariate analysis of inkjet printed a-WO3/TiO2/WOX electrochromic films.

Science.gov (United States)

Wojcik, Pawel Jerzy; Pereira, Luís; Martins, Rodrigo; Fortunato, Elvira

2014-01-13

An efficient mathematical strategy in the field of solution processed electrochromic (EC) films is outlined as a combination of an experimental work, modeling, and information extraction from massive computational data via statistical software. Design of Experiment (DOE) was used for statistical multivariate analysis and prediction of mixtures through a multiple regression model, as well as the optimization of a five-component sol-gel precursor subjected to complex constraints. This approach significantly reduces the number of experiments to be realized, from 162 in the full factorial (L=3) and 72 in the extreme vertices (D=2) approach down to only 30 runs, while still maintaining a high accuracy of the analysis. By carrying out a finite number of experiments, the empirical modeling in this study shows reasonably good prediction ability in terms of the overall EC performance. An optimized ink formulation was employed in a prototype of a passive EC matrix fabricated in order to test and trial this optically active material system together with a solid-state electrolyte for the prospective application in EC displays. Coupling of DOE with chromogenic material formulation shows the potential to maximize the capabilities of these systems and ensures increased productivity in many potential solution-processed electrochemical applications.

Design and construction of hierarchical TiO2 nanorod arrays by combining layer-by-layer and hydrothermal crystallization techniques for electrochromic application

Science.gov (United States)

Chen, Yongbo; Li, Xiaomin; Bi, Zhijie; He, Xiaoli; Li, Guanjie; Xu, Xiaoke; Gao, Xiangdong

2018-05-01

The hierarchical TiO2 (H-TiO2) nanorod arrays (NRAs) composed of single-crystalline nanorods and nanocrystals were finely designed and successfully constructed for electrochromic (EC) application. By combining layer-by-layer (LBL) method and hydrothermal crystallization technique, the superfine nanocrystals (5-7 nm), which can provide abundant active sites and facilitate ion insertion/extraction during EC reactions, were uniformly and conformally assembled on the surface of single-crystalline TiO2 (SC-TiO2) NRAs. The as-formed H-TiO2 NRAs integrate the advantages of one-dimensional NRAs with fast kinetics and superfine nanocrystals with high ion capacity, showing highly enhanced EC performance. Large optical contrast (40.3%), shorter coloring/bleaching time (22/4 s), high coloration efficiency (11.2 cm2 C-1), and excellent cycling stability can be achieved in H-TiO2 NRAs, superior to the pristine SC-TiO2 NRAs and nanocrystalline TiO2 films. This work provides a feasible and well-designed strategy to explore high-performance materials for EC application.

Caracterização de filmes finos de Nb2O5 com propriedades eletrocrômicas Caracterization of OF Nb2O5 thin films with electrochromic properties

Directory of Open Access Journals (Sweden)

C. O. Avellaneda

1998-06-01

Full Text Available The sols for thin electrochromic coatings of Nb2O5 were obtained by synthesis of the niobium butoxide from BuONa and NbCl5. The ~300nm thick films were deposited by dip-coating technique from the alkoxide solution and calcined at 560ºC in O2 atmosphere during 3 hours. The particles size of niobium oxide (V powder (~20mm was obtained from x-ray diffraction using the Scherrer equation. The coatings were characterized by cyclic voltammetry and cronoamperommetry techniques. The spectral variation of the optical transmittance were determined in situ as a function of the cyclical potencial and memory effect. The insertion process of lithium is reversible and change the film color from transparent (T=80% to dark blue (T=20%.

Efficient synthesis of tungsten oxide hydrate-based nanocomposites for applications in bifunctional electrochromic-energy storage devices

Science.gov (United States)

Chang, Xueting; Hu, Ruirui; Sun, Shibin; Lu, Tong; Liu, Tao; Lei, Yanhua; Dong, Lihua; Yin, Yansheng; Zhu, Yanqiu

2018-05-01

In this work, we realized the large-scale synthesis of WO3 · H2O nanoflakes (NFs), g-C3N4/WO3 · H2O nanocomposite (NC) and graphene (G)/WO3 · H2O NC via a sonochemical process with tungsten salt as the precursor, g-C3N4 or G sheets as the supports, and distilled water as the solvent. Both the g-C3N4/WO3 · H2O NC and G/WO3 · H2O NC exhibited much better electrochromic (EC) performance (higher coloration efficiencies and faster response times) than that of the WO3 · H2O NFs. Using the WO3 · H2O-based materials as electrode materials, EC batteries that integrate the energy storage and EC functions in one device have been assembled. The energy status of the EC batteries could be visually indicated by the reversible color variations. Compared with the plain WO3 · H2O-based EC batteries, the NC-based EC batteries possessed a lower color contrast between the charged and discharged conditions but much longer discharge durations. The EC batteries could be quickly charged in a few seconds by adding H2O2, and the charged batteries exhibited significantly-enhanced discharging durations in comparison with the initial ones. The g-C3N4/WO3 · H2O NC-EC batteries charged by a small amount of H2O2 could produce a long discharging duration up to 760 min.

Structure, stability and electrochromic properties of polyaniline film covalently bonded to indium tin oxide substrate

Energy Technology Data Exchange (ETDEWEB)

Zhang, Wenzhi, E-mail: zhangwz@xatu.edu.cn [Key Laboratory for Photoelectric Functional Materials and Devices of Shaanxi Province, School of Materials and Chemical Engineering, Xi’an Technological University, Xi’an 710021 (China); Ju, Wenxing; Wu, Xinming; Wang, Yan; Wang, Qiguan; Zhou, Hongwei; Wang, Sumin [Key Laboratory for Photoelectric Functional Materials and Devices of Shaanxi Province, School of Materials and Chemical Engineering, Xi’an Technological University, Xi’an 710021 (China); Hu, Chenglong [Key Laboratory of Optoelectronic Chemical Materials and Devices of Ministry of Education, School of Chemistry and Environmental Engineering, Jianghan University, Wuhan 430056 (China)

2016-03-30

Graphical abstract: A chemical bonding approach was proposed to prepare the PANI film covalently bonded to ITO substrate and the film exhibited high electrochemical activities and stability compared with that obtained by conventional film-forming approach. - Highlights: • The PANI film covalently bonded to ITO substrate was prepared using ABPA as modifier. • The oxidative potentials of the obtained PANI film were decreased. • The obtained PANI film exhibits high electrochemical activities and stability. - Abstract: Indium tin oxide (ITO) substrate was modified with 4-aminobenzylphosphonic acid (ABPA), and then the polyaniline (PANI) film covalently bonded to ITO substrate was prepared by the chemical oxidation polymerization. X-ray photoelectron spectroscopy (XPS), attenuated total reflection infrared (ATR-IR) spectroscopy, and atomic force microscopy (AFM) measurements demonstrated that chemical binding was formed between PANI and ABPA-modified ITO surface, and the maximum thickness of PANI layer is about 30 nm. The adhesive strength of PANI film on ITO substrate was tested by sonication. It was found that the film formed on the modified ITO exhibited a much better stability than that on bare one. Cyclic voltammetry (CV) and UV–vis spectroscopy measurements indicated that the oxidative potentials of PANI film on ABPA-modified ITO substrate were decreased and the film exhibited high electrochemical activities. Moreover, the optical contrast increased from 0.58 for PANI film (without ultrasound) to 1.06 for PANI film (after ultrasound for 60 min), which had an over 83% enhancement. The coloration time was 20.8 s, while the bleaching time was 19.5 s. The increase of electrochromic switching time was due to the lower ion diffusion coefficient of the large cation of (C{sub 4}H{sub 9}){sub 4}N{sup +} under the positive and negative potentials as comparison with the small Li{sup +} ion.

Applications of Tris(4-(thiophen-2-ylphenylamine- and Dithienylpyrrole-based Conjugated Copolymers in High-Contrast Electrochromic Devices

Directory of Open Access Journals (Sweden)

Tzi-Yi Wu

2016-05-01

Full Text Available Tris(4-(thiophen-2-ylphenylamine- and dithienylpyrrole-based copolymers (P(TTPA-co-DIT and P(TTPA-co-BDTA were electropolymerized on ITO electrode by applying constant potentials of 1.0, 1.1, and 1.2 V. Spectroelectrochemical investigations revealed that P(TTPA-co-DIT film displayed more color changes than P(TTPA-co-BDTA film. The P(TTPA-co-DIT film is yellow in the neutral state, yellowish-green and green in the intermediate state, and blue (1.2 V in highly oxidized state. The ∆Tmax of the P(TTPA-co-DIT and P(TTPA-co-BDTA films were measured as 60.3% at 1042 nm and 47.1% at 1096 nm, respectively, and the maximum coloration efficiency (η of P(TTPA-co-DIT and P(TTPA-co-BDTA films were calculated to be 181.9 cm2·C−1 at 1042 nm and 217.8 cm2·C−1 at 1096 nm, respectively, in an ionic liquid solution. Dual type electrochromic devices (ECDs consisting of P(TTPA-co-DIT (or P(TTPA-co-BDTA anodic copolymer, ionic liquid-based electrolyte, and poly(3,4-(2,2-diethylpropylenedioxythiophene (PProDOT-Et2 cathodic polymer were constructed. P(TTPA-co-BDTA/PProDOT-Et2 ECD showed high ΔTmax (48.1% and high coloration efficiency (649.4 cm2·C−1 at 588 nm. Moreover, P(TTPA-co-DIT/PProDOT-Et2 and P(TTPA-co-BDTA/PProDOT-Et2 ECDs displayed satisfactory optical memory and long term switching stability.

Photochromic and electrochromic performances of new types of donor/acceptor systems based on crosslinked polyviologen film and electron donors

International Nuclear Information System (INIS)

Gao Liping; Ding Guojing; Li Chaolong; Wang Yuechuan

2011-01-01

Viologen-functionalized copolymer COPV 2+ was synthesized by copolymer graft-modified, which was crosslinked by NH 3 .H 2 O gas-fumigated at 25 deg. C for 4 h due to the condensation of the siloxanes of COPV 2+ film. Simultaneously, different donor/acceptor systems had been prepared based on crosslinked polyviologen film (COPV 2+ ) and N,N,N',N'-tetramethyl-1,4-phenylenediamine (TMPD) or hydroxyethylferrocene (HEFc) in order to shorten the response times and improve contrast ratios in response to external photo- and potential stimuli. The evolution of structures from COPO to COPV 2+ is carefully characterized. The COPV 2+ /TMPD and COPV 2+ /HEFc films exhibited both photochromic and electrochromic performances. After UV irradiations, COPV 2+ /TMPD and COPV 2+ /HEFc films changed their colors from colorless to deep blue, while optical transmissions at 610 nm decreased about 64% and 75%, respectively. When removing out from UV irradiation, the colored COPV 2+ /TMPD and COPV 2+ /HEFc films faded to the original colors within about 60 min. When COPV 2+ /TMPD and COPV 2+ /HEFc films were biased with negative voltage of -2.5 V, they changed their colors from colorless to deep blue in 4 s and 3 s, while the optical transmissions at 556 nm decreased about 81% and 75%, respectively. When electric impulse was switched off, the colored COPV 2+ /TMPD and COPV 2+ /HEFc films faded to the original colors within about 7 s and 6 s, respectively.

PEDOT

Indian Academy of Sciences (India)

WINTEC

attention because of their use in sensors, actuators, LEDs, electrochromic devices ... the present electrochromic device research and activities. Here we have attempted .... divided by the charge density of the colouration process. Colouration ...

Bulletin of Materials Science | Indian Academy of Sciences

Indian Academy of Sciences (India)

Electrochromic devices; conducting polymers; PEDOT; indium tin oxide. Abstract. Conjugated polymers are promising materials for electrochromic device technology. Aqueous dispersions of poly(3,4-ethylenedioxythiophene)-(PEDOT) were spin coated onto transparent conducting oxide (TCO) coated glass substrates.

Dithienylpyrrole- and Tris[4-(2-thienylphenyl]amine-Containing Copolymers as Promising Anodic Layers in High-Contrast Electrochromic Devices

Directory of Open Access Journals (Sweden)

Tzi-Yi Wu

2018-04-01

Full Text Available Three dithienylpyrrole- and tris[4-(2-thienylphenyl]amine-containing copolymers (P(MPS-co-TTPA, P(MPO-co-TTPA, and P(ANIL-co-TTPA were deposited on indium tin oxide (ITO surfaces using electrochemical polymerization. Spectroelectrochemical characterizations of polymer films revealed that P(MPS-co-TTPA film was light olive green, greyish-green, bluish grey, and grey in neutral state, intermediate state, oxidized state, and highly oxidized state, respectively, whereas P(MPO-co-TTPA film was green moss, foliage green, dark greyish-green, and bluish-grey in neutral state, intermediate state, oxidized state, and highly oxidized state, respectively. The ΔTmax of P(MPS-co-TTPA film at 964 nm, P(MPO-co-TTPA film at 914 nm, and P(ANIL-co-TTPA film at 960 nm were 67.2%, 60.7%, and 67.1%, respectively, and the coloration efficiency (η of P(MPS-co-TTPA film at 964 nm, P(MPO-co-TTPA film at 914 nm, and P(ANIL-co-TTPA film at 960 nm were calculated to be 260.3, 176.6, and 230.8 cm2 C−1, respectively. Dual type complementary colored electrochromic devices (ECDs were constructed using P(MPS-co-TTPA, P(MPO-co-TTPA, or P(ANIL-co-TTPA as anodic copolymer layer and PProDOT-Et2 as cathodic polymer layer. P(MPO-co-TTPA/PProDOT-Et2 ECD revealed high ΔT (55.1% and high η (766.5 cm2 C−1 at 580 nm. Moreover, P(MPS-co-TTPA/PProDOT-Et2, P(MPO-co-TTPA/PProDOT-Et2, and P(ANIL-co-TTPA/PProDOT-Et2 ECDs showed satisfactory long-term cycling stability and optical memory.

Electrochemistry and spectroelectrochemistry of tert-butylcalix[4]arene bridged bis double-decker lutetium(III) phthalocyanine, Lu2Pc4 and dimeric lutetium(III) phthalocyanine, Lu2Pc2(OAc)2

International Nuclear Information System (INIS)

Koca, Atif; Ceyhan, Tanju; Erbil, Mehmet K.; Ozkaya, Ali Riza; Bekaroglu, Ozer

2007-01-01

In this study, electrochemical, electrochromic and spectroelectrochemical properties of a tert-butylcalix[4]arene bridged bis double-decker lutetium(III) phthalocyanine (Lu 2 Pc 4 2) were investigated explicitly as compared with a tert-butylcalix[4]arene bridged dimeric lutetium(III) phthalocyanine [Lu 2 Pc 2 (OAc) 2 1]. Distinctive differences between electrochemical and electrochromic properties of 1 and 2 were detected. Moreover, the properties of 1 and 2 were compared with previously reported S 4 (CH 2 ) 4 bridged Lu 2 Pc 2 (OAc) 2 and Lu 2 Pc 4 . The calixarene bridged phthalocyanine (Pc) compounds, 1 and 2 showed well-defined electrochromic behaviour with green-blue and blue-purple colour transitions. The enhanced electrochromic properties of 2, as compared to 1, were attributed to its double-decker structure, probably allowing the formation of suitable ion channels for the counter ion movement in the solid film

Color change at the push of a buttom; Farbwechsel auf Knopfdruck

Energy Technology Data Exchange (ETDEWEB)

Mortimer, Roger J. [Loughborough Univ. (United Kingdom)

2013-05-15

Materials with electrically switchable color open up many fascinating application possibilities - from the glare protection on low-cost displays to adaptive camouflage. Electrochromic materials can be electrically switched between different colors back and forth. The effect is based on a change of light absorption by current induced oxidation and reduction processes. Meanwhile electrochromic materials cover the entire color spectrum. In addition, the electrochromic materials are inexpensive and consume little power. This makes them attractive for many applications. However, their response times are still relatively long. The first commercial products include mirrors with automatic anti-glare and aircraft windows that can be darkened electrically.

Electro-optical properties of poly[di(2-thiophenyl)carborane] and its opto-electronic application

International Nuclear Information System (INIS)

Cansu-Ergun, Emine Gul; Cihaner, Atilla

2013-01-01

Electrochemical and optical properties of a hybrid carborane based polymer called poly(di(2-thiophenyl)carborane) (P1) obtained electrochemically were reported as well as its electrochromic device application. Thiophene donor units and m-carborane acceptor unit were combined under the same umbrella via donor–acceptor–donor approach to obtain di(2-thiophenyl)carborane (1). Contrary to the literature, extreme conditions like highly dried solvent or inert atmosphere were not used for polymerization and characterization. Polymer P1 has an ambipolar character since it exhibited a reversible oxidation peak at a half wave potential (E 1/2 ) of 1.08 V and a quasi reversible reduction peak at E 1/2 = −1.82 V vs. Ag/AgCl. The polymer film has an optical band gap of 1.95 eV with a maximum absorption band centered at 488 nm. Also, it exhibited multicolor electrochromic behavior between its reduced and oxidized states changing from dark orange to light blue. Furthermore, the electrochromic device prepared based on P1 film was stable and robust. - Highlights: • Electrochromic properties of a carborane based conjugated polymer were reported. • The polymer exhibited an ambipolar character and multicolor behaviors. • It is the first electrochromic device based on a carborane unit

Electrochemistry and spectroelectrochemistry of tert-butylcalix[4]arene bridged bis double-decker lutetium(III) phthalocyanine, Lu{sub 2}Pc{sub 4} and dimeric lutetium(III) phthalocyanine, Lu{sub 2}Pc{sub 2}(OAc){sub 2}

Energy Technology Data Exchange (ETDEWEB)

Koca, Atif [Chemical Engineering Department, Engineering Faculty, Marmara University, TR34722 Goeztepe, Istanbul (Turkey); Ceyhan, Tanju; Erbil, Mehmet K. [Department of Biochemistry, Division of Organic Chemistry, Guelhane Medical Academy (GATA), Ankara (Turkey); Ozkaya, Ali Riza [Department of Chemistry, Marmara University, TR34722 Goeztepe, Istanbul (Turkey)], E-mail: aliozkaya@marmara.edu.tr; Bekaroglu, Ozer [Department of Chemistry, Technical University of Istanbul, TR34469 Maslak, Istanbul (Turkey)], E-mail: obek@itu.edu.tr

2007-11-09

In this study, electrochemical, electrochromic and spectroelectrochemical properties of a tert-butylcalix[4]arene bridged bis double-decker lutetium(III) phthalocyanine (Lu{sub 2}Pc{sub 4}2) were investigated explicitly as compared with a tert-butylcalix[4]arene bridged dimeric lutetium(III) phthalocyanine [Lu{sub 2}Pc{sub 2}(OAc){sub 2}1]. Distinctive differences between electrochemical and electrochromic properties of 1 and 2 were detected. Moreover, the properties of 1 and 2 were compared with previously reported S{sub 4}(CH{sub 2}){sub 4} bridged Lu{sub 2}Pc{sub 2}(OAc){sub 2} and Lu{sub 2}Pc{sub 4}. The calixarene bridged phthalocyanine (Pc) compounds, 1 and 2 showed well-defined electrochromic behaviour with green-blue and blue-purple colour transitions. The enhanced electrochromic properties of 2, as compared to 1, were attributed to its double-decker structure, probably allowing the formation of suitable ion channels for the counter ion movement in the solid film.

APCVD Transition Metal Oxides – Functional Layers in ''Smart windows''

International Nuclear Information System (INIS)

Gesheva, K A; Ivanova, T M; Bodurov, G K

2014-01-01

Transition metal oxides (TMO) exhibit electrochromic effect. Under a small voltage they change their optical transmittance from transparent to collored (absorbing) state. The individual material can manifest its electrochromic properties only when it is part of electrochromic (EC) multilayer system. Smart window is controlling the energy of solar flux entering the building or car and makes the interiors comfortable and energy utilization more effective. Recently the efforts of material researchers in this field are directed to price decreasing. APCVD technology is considered as promissing as this process permits flowthrough large-scale production process. The paper presents results on device optimization based on WO 3 -MoO 3 working electrode. Extensive research reveals that WO 3 -MoO 3 structure combines positive features of single oxides: excellent electrochromic performance of WO 3 and better kinetic properties of MoO 3 deposition. The achieved color efficiency of APCVD WO 3 -MoO 3 films is 200cm 2 /C and optical modulation of 65-70% are practically favorable electrochromic characteristics. To respond to low cost requirement, the expensive hexacarbonyl can be replaced with acetylacetonate. We have started with this precursor to fabricate mixed W x V 1-x O 3 films. The films possess excellent surface coverage and high growth-rate. CVD deposition of VO 2 , a promissing thermochromic thin film material is also presented

Preparation and characterization of nanocrystalline porous TiO2/WO3 composite thin films

International Nuclear Information System (INIS)

Hsu, C.-S.; Lin, C.-K.; Chan, C.-C.; Chang, C.-C.; Tsay, C.-Y.

2006-01-01

TiO 2 materials possessing not only photocatalytic but also electrochromic properties have attracted many research and development interests. Though WO 3 exhibits excellent electrochromic properties, the much higher cost and water-sensitivity of WO 3 as compared with the TiO 2 may restrict the practical application of WO 3 materials. In the present study, the feasibility of preparing nanocrystalline porous TiO 2 /WO 3 composite thin films was investigated. Precursors of sols TiO 2 and/or WO 3 and polystyrene microspheres were used to prepare nanocrystalline pure TiO 2 , WO 3 , and composite TiO 2 /WO 3 thin films by spin coating. The spin-coated thin films were amorphous and, after heat treating at a temperature of 500 o C, nanocrystalline TiO 2 , TiO 2 /WO 3 , and WO 3 thin films with or without pores were prepared successfully. The heat-treated thin films were colorless and coloration-bleaching phenomena can be observed during cyclic voltammetry tests. The heat-treated thin films exhibited good reversible electrochromic behavior while the porous TiO 2 /WO 3 composite film exhibited improved electrochromic properties

Couches minces electrochromiques d'oxyde de tungstene dense et poreux pour des applications de controle energetique

Science.gov (United States)

Camirand, Hubert

Nanotechnology has modified the landscape of energy generation, energy storage and energy saving devices. Architectural fenestration can extensively benefit from green nanotechnologies. Amongst them, active fenestration or "smart" windows are able to modify their coloration state upon the application of a small electrical voltage, when based on electrochromic materials. In fact, the amount of visible and near-infrared light that can penetrate through the window can be altered. Therefore, their implementation can allow for a significant reduction in energy consumption in buildings. Furthermore, the capability of optimizing indoor comfort is user-controlled, thus an additional degree of freedom is given by electrochromic-based technology. It is worth mentioning that such devices can be largely advantageous in countries with variable seasons, such as here in Canada. As a matter of fact, the large temperature difference between the hot and cold season influences the requirement of impeding or enabling visible and thermal radiation to pass through. This master's thesis is entirely devoted to tungsten trioxide (WO 3), which is the most widely studied electrochromic material. In the present case, WO3 thin films are synthesized by radiofrequency magnetron sputtering. By varying the deposition pressure and power, the porosity content/packing density of the films is modified. This work's main topic is the characterization of electrochromic samples by in situ spectroscopic ellipsometry simultaneously with the application of an electrical voltage in an aqueous electrolytic medium made of sulfuric acid (H2SO 4). The methodology developed here allows for an in-depth study of electro-active materials. To corroborate this, optical properties of WO3 are obtained for a wide range of coloration levels, and these are subsequently used to model the resulting coloration of electrochromic multilayer systems. However, the interface between the dense and porous films affects the coloration

Eletrodos modificados por hidróxido de níquel: um estudo de revisão sobre suas propriedades estruturais e eletroquímicas visando suas aplicações em eletrocatálise, eletrocromismo e baterias secundárias Nickel hydroxide modified electrodes: a review study concerning its structural and electrochemical properties aiming the application in electrocatalysis, electrochromism and secondary batteries

Directory of Open Access Journals (Sweden)

Marcio Vidotti

2010-01-01

Full Text Available The present review paper describes the main features of nickel hydroxide modified electrodes covering its structural and electrochemical behavior and the newest advances promoted by nanostructured architectures. Important aspects such as synthetic procedures and characterization techniques such as X-Ray diffraction, Raman and Infrared spectroscopy, Electronic Microscopy and many others are detailed herein. The most important aspect concerning nickel hydroxide is related to its great versatility covering different fields in electrochemical-based devices such as batteries, electrocatalytic systems and electrochromic electrodes, the fundamental issues of these devices are also commented. Finally, some of the newest advances achieved in each field by the incorporation of nanomaterials will be shown.

Optical materials technology for energy efficiency and solar energy conversion III; Proceedings of the Meeting, San Diego, CA, August 21-23, 1984

Science.gov (United States)

Lampert, C. M.

1984-01-01

Transparent heat mirror films are discussed, taking into account bandgap widening in heavily doped oxide semiconductors used as transparent heat-reflectors, the characterization of a low emissivity coating in large scale production, an exact analysis of radiative and conductive heat transfer through radiative gray films, and process control for sputter deposition of low emissivity films in large scale production. Other topics explored are related to optical switching materials, selective absorber coatings, general solar optical materials and instrumentation, and technical needs of the energy related coatings industry and the building sciences. Attention is given to electrochromic coatings for 'smart windows', materials for electrochromic windows, optical frequencies free electron scattering studies on electrochromic materials for variable reflectivity windows, progress on solar absorber selective paint research, complex index interference films on metal substrates, luminescent solar concentrator daylighting, and research on passive solar materials in Canada.

Conjugated Polymers Atypically Prepared in Water

Science.gov (United States)

Invernale, Michael A.; Pendergraph, Samuel A.; Yavuz, Mustafa S.; Ombaba, Matthew; Sotzing, Gregory A.

2010-01-01

Processability remains a fundamental issue for the implementation of conducting polymer technology. A simple synthetic route towards processable precursors to conducting polymers (main chain and side chain) was developed using commercially available materials. These soluble precursor systems were converted to conjugated polymers electrochemically in aqueous media, offering a cheaper and greener method of processing. Oxidative conversion in aqueous and organic media each produced equivalent electrochromics. The precursor method enhances the yield of the electrochromic polymer obtained over that of electrodeposition, and it relies on a less corruptible electrolyte bath. However, electrochemical conversion of the precursor polymers often relies on organic salts and solvents. The ability to achieve oxidative conversion in brine offers a less costly and a more environmentally friendly processing step. It is also beneficial for biological applications. The electrochromics obtained herein were evaluated for electronic, spectral, and morphological properties. PMID:20959869

Electrochromic Glasses.

Science.gov (United States)

1980-07-31

this glass and that dipole-dipole correlations contribute to the "ferroelectric-like" character of this amorphous system. The TeO2 -W03 glasses can only...shows the dielectric constant and Fig. I(b) glass from pure TeO2 ot pure WO. In addition, glass the tan 8 of the WO glass as a function of temperature... glasses containing WO, in various glass forming nitworks of LifO-B1O0, Na:O-BzO,, and TeO2 were prepared from reagent grade oxides at 800 C - 9SO C in

Thin film-based optically variable security devices: From passive to active

Science.gov (United States)

Baloukas, Bill

Counterfeiting costs the world economy billions of dollars every year. Aside from financial losses, counterfeiting also poses a great threat to the public's safety, for example through the existence of counterfeit passports (terrorism), pharmaceutical products (health hazards) and even airplane parts (safety issues). Optical security devices (OSDs) have therefore played a critical role in the fight against counterfeiting. It is the aim of the present thesis to show that through the use of metamerism and electrochromic materials, new types of active security devices with interesting features can be created; indeed, most present-day devices are passive in nature. I first demonstrate that the addition of metamerism in the design of interference filters can result in innovative features. Different structures which can be used in transmission and/or in reflection are designed, fabricated, and evaluated. The first structures which are presented here are based on a combination of two different metameric interference filters. Possessing widely different transmission spectra, these filters also offer different angular color shifts and, as a result, offer an opportunity of creating hidden image effects. Despite their interesting properties, such metameric devices are shown to be highly illuminant and observer sensitive; that is the color match is lost under most observation conditions. These issues are solved by a simpler structure based on the juxtaposition of an interference filter and a non-iridescent colored material. Throughout this study, I present the design approach, analyze the filters' sensitivity to deposition errors, and evaluate the performance of prototype devices prepared by dual ion beam sputtering. Following my work on passive metameric systems, I then propose to go one step further by implementing an active component using an electrochromic material. This novel concept, which is based on the joint use of a metameric filter and electrochromic device, offers

Optical characterization of niobium pentoxide thin films

International Nuclear Information System (INIS)

Pawlicka, A.

1996-01-01

Thin films of Nb 2 O 5 were obtained by sol-gel method using ultrasonic irradiation and deposited by dip-coating technique. After calcination at temperatures superior than 500 deg C these films (300 nm thick) were characterized by cyclic voltametry and cronoamperometry. The memory measurements, color efficiency, optical density as a function of wave number and applied potential were effectuated to determine their electrochromic properties. The study of electrochromic properties of these films shows that the insertion process of lithium is reversible and changes their coloration from transparent (T=80%) to dark blue (T=20%). (author)

Printable organic and inorganic materials for flexible electrochemical devices

Science.gov (United States)

Wojcik, Pawel Jerzy

The growing demand of consumer printed electronics such as smart cards, smart packaging, automotive displays, electronic paper and others led to the increased interest in fully printed electrochemical devices. These components are expected to be developed based on printed thin films derived from cheap and widely accessible compounds. This dissertation presents the long stretch of technical research that was performed to realize printed energy efficient concepts such as electrochromic displays and smart-windows. Within this broad theme, the presented study had a number of specific objectives, however, the overall aim was to develop low-cost material systems (i.e. printable mixtures) at a lab-scale, which would be compatible with large-scale roll-to-roll processing. Presented results concern three main topics: (i) dual-phase inorganic electrochromic material processed at low temperature, (ii) enhancement in electrochromic performance via metaloxide nanoparticles engineering, and (iii) highly conductive and mechanically stable solid-state electrolyte. First two topics are related to crystallographic structure of metal-oxide films derived from sol-gel precursor, which is shown to be critical for electrochemical performance. The proposed method of microstructure control enables development of electrochromic films which outperform their amorphous or nanocrystalline analogues presented in the state-of-the-art due to their superior chemical and physical properties. Developed materials and processes resulted in electrochemical devices exhibiting optical density on the level of 0.82 and switching time shorter than 3 seconds, reaching performance at practical level. Third topic concerns a new concept of solid state electrolyte based on plastic crystal doped with lithium salt, dispersed in a thermosetting polymer resin network. This soft matter printable electrolyte meets requirements for electrochromic applications, exhibiting ionic conductivities of 10. -6 - 10. -4 S cm-1 at

Trinuclear ruthenium dioxolene complexes based on the bridging ligand hexahydroxytriphenylene: electrochemistry, spectroscopy, and near-infrared electrochromic behaviour associated with a reversible seven-membered redox chain.

Science.gov (United States)

Grange, Christopher S; Meijer, Anthony J H M; Ward, Michael D

2010-01-07

The trinuclear complexes [{(R2bipy)2Ru}3(mu3-HHTP)](PF6)3 [1(PF6)3, R = H; 2(PF6)3, R = 4-tBu] contain three {Ru(R2bipy)2}2+ fragments connected to the triangular tris-chelating ligand hexahydroxytriphenylene (H6HHTP). This bridging ligand contains three dioxolene-type binding sites, each of which can reversibly convert between dianionic catecholate (cat), monoanionic semiquinone (sq) or neutral quinone (q) redox states. The bridging ligand as a whole can therefore exist in seven different redox states from fully reduced [cat,cat,cat]6- through to fully oxidised, neutral [q,q,q]. Cyclic voltammetry of 1(PF6)3 in MeCN reveals six redox processes of which the three at more positive potentials (the sq/q couples) are reversible but the three at more negative potentials (the sq/cat couples) are irreversible with distorted wave shapes due to the insolubility of the reduced forms of the complex. In contrast, the more soluble complex 2(PF6)3 displays six reversible one-electron redox processes making all components of a seven-membered redox chain accessible. UV/Vis/NIR spectro-electrochemical studies reveal rich spectroscopic behaviour, with--in particular--very intense transitions in the near-IR region in many of the oxidation states associated with Ru(II)-->(dioxolene) MLCT and bridging ligand centred pi-pi* transitions. TDDFT calculations were used to analyse the electronic spectra in all seven oxidation states; the calculated spectra generally show very good agreement with experiment, which has allowed a fairly complete assignment of the low-energy transitions. The strong electrochromism of the complexes in the near-IR region has formed the basis of an optical window in which a thin film of 1(PF6)3 or 2(PF6)3 on a conductive glass surface can be reversibly and rapidly switched between redox states that alternate between strongly absorbing or near-transparent at 1100 nm, with--for 2(PF6)3--the switching being stable and reversible in water over thousands of cycles.

Controlled Redox and Electrical Properties in Polyheterocycles

National Research Council Canada - National Science Library

Reynolds, John

2001-01-01

Electrochromic and conducting polymers may prove especially important for a number of Air Force applications including chameleon coatings, informational displays, IR and microwave attenuation, dialed...

Controlled Redox and Electrical Properties in Polyheterocycles

National Research Council Canada - National Science Library

Reynolds, John

2000-01-01

Electrochromic polymers may prove especially important for a number of Air Force applications including chameleon coatings, informational displays, IR and microwave attenuation, and dialed tint windows...

Intelligent Variable Emittance Panels Using New, ""True"" Solid Electrolyte, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — This work further developed a highly promising Variable Emittance technology for spacecraft thermal control based on Conducting Polymer (CP) electrochromics...

Chromophore

Directory of Open Access Journals (Sweden)

Roxana Gabriela Zgârian

2017-02-01

Full Text Available The paper presents the main results of our study on preparation and characterization of conducting biomembranes to be used as solid polymer electrolytes (SPEs. It bases on deoxyribonucleic acid (DNA, glycerol (GLY and photosensitive chromophores, like Prussian Blue (PB. Its primary application is in fabrication of electrochromic windows. The new SPEs were characterized by UV-VIS and FTIR spectroscopy. They were used in preparation of small electrochromic devices (ECDs. The obtained devices were evaluated by cyclic voltammetry and also by spectroscopic methods. The results show their color change from blue pale to intense blue after application of a direct current (DC electric field, making the composites very interesting for industrial applications in smart windows.

In-situ transmission electron microscopy imaging of formation and evolution of LixWO3 during lithiation of WO3 nanowires

International Nuclear Information System (INIS)

Qi, Kuo; Li, Xiaomin; Sun, Muhua; Huang, Qianming; Wei, Jiake; Xu, Zhi; Wang, Wenlong; Bai, Xuedong; Wang, Enge

2016-01-01

The phase transition from monoclinic WO 3 to cubic Li x WO 3 during lithiation of WO 3 is one of the key features for tungsten oxide as the most used electrochromic material. Conventionally, the lithium intercalation of WO 3 has been studied by building generic layered electrochromic device combining with structural characterization and electrochemistry measurement at macro scale. In-situ transmission electron microscopy (in-situ TEM) has been proposed as a method for revealing the detailed mechanism of structural, physical, and chemical properties. Here, we use in-situ TEM method to investigate the formation and evolution of Li x WO 3 in real-time during the electrochemical lithiation of WO 3 nanowires. The dynamic lithiation process is recorded by TEM imaging, diffraction, and electron energy loss spectroscopy. The WO 3 -Li x WO 3 phase boundary of reaction front has been observed at high resolution. The timeliness of crystallinity of Li x WO 3 and the intercalation channels for Li ions are also identified. Moreover, the co-existence of both polycrystalline Li-poor area and amorphous Li-rich phases of Li x WO 3 was found. Our results provide an insight into the basic lithiation process of WO 3 , which is significantly important for understanding the electrochromic mechanism of tungsten oxide.

Deep reduced PEDOT films support electrochemical applications: Biomimetic color front.

Directory of Open Access Journals (Sweden)

Toribio Fernandez OTERO

2015-02-01

Full Text Available Most of the literature accepts, despite many controversial results, that during oxidation/reduction films of conducting polymers move from electronic conductors to insulators. Thus, engineers and device’s designers are forced to use metallic supports to reoxidize the material for reversible device work. Electrochromic front experiments appear as main visual support of the claimed insulating nature of reduced conducting polymers. Here we present a different design of the biomimetic electrochromic front that corroborates the electronic and ionic conducting nature of deep reduced films. The direct contact PEDOT metal/electrolyte and film/electrolyte was prevented from electrolyte contact until 1cm far from the metal contact with protecting Parafilm®. The deep reduced PEDOT film supports the flow of high currents promoting reaction induced electrochromic color changes beginning 1 cm far from the metal-polymer electrical contact and advancing, through the reduced film, towards the metal contact. Reverse color changes during oxidation/reduction always are initiated at the film/electrolyte contact advancing, under the protecting film, towards the film/metal contact. Both reduced and oxidized states of the film demonstrate electronic and ionic conductivities high enough to be used for electronic applications or, as self-supported electrodes, for electrochemical devices. The electrochemically stimulated conformational relaxation (ESCR model explains those results.

Nanomaterials for LightManagement in Electro-Optical Devices

Energy Technology Data Exchange (ETDEWEB)

Truong, Vo-Van [Concordia University, Montréal, Québec, H4B 1R6, Canada; Singh, Jai [Charles Darwin University, Darwin, Australia; Tanemura, Sakae [Japan Fine Ceramics Center, Nagoya, Japan; Hu, Michael Z. [ORNL

2012-01-01

In the past decade, nanostructured materials and nanoparticles have emerged as the necessary ingredients for electrooptical applications and enhancement of device performance, in particular by making use of the light management aspects of the nanomaterials. The application areas that are being transformed profoundly include smart coating devices (e.g., electrochromic, photochromic, and thermochromic devices), solar energy, and sensing. Despite the large volume of work in the past on smart coating devices, and in particular on electrochromic devices and thermochromic fenestrations, for optical transmission or reflection control, applications remain limited because of slow response time and nonuniformity in the case of large surfaces. Recent works in the field indicate that nanostructured electrochromic coatings would be an integral part of the solution to the above problem. One aspect that can thus be focused on would be the fabrication and characterization of the nanostructured smart coating materials and their compatibility with other layers in the overall smart coating device. In the area of solar photovoltaics, nanomaterials have been used in designing light-trapping schemes for inorganic as well as organic solar cells. One particular category of solar cells that has attracted much interest is the plasmonic solar cells in which metallic nanoparticles are incorporated, helping in enhancing their energy conversion efficiency. Nanostructured solar cells would eventually develop into a 'game changing' technology for making solar cells that are affordable and highly efficient, providing a sizeable alternative energy source for our ever-increasing energy needs. Sensors based on the optical properties of constituting nanostructures and nanoparticles also form a most interesting class of bio- and electrochemical sensing devices. The possibility of synthetizing nanoparticles and structures of specifically desired sizes and shapes has indeed opened a whole new

Intelligent Variable Emittance Panels Using New, ?True? Solid Electrolyte, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This firm has, in ongoing work in collaboration with the Air Force, NASA and JPL, developed a unique Variable Emittance technology based on the electrochromism of...

Influence of annealing temperature on microstructure and optical properties of sol-gel derived tungsten oxide films

International Nuclear Information System (INIS)

Sun Xilian; Cao Hongtao; Liu Zhimin; Li Jianzhong

2009-01-01

Tungsten oxide (WO 3 ) thin films have been extensively studied for their interesting physical properties and a variety of potential applications in electrochromic devices. In order to explore the possibility of using these in electrochromic devices, a preliminary and thorough study of the optical properties of the host materials is an important step. Based on this, the influence of annealing temperature on the structural, surface morphological, optical and electrochromic properties has been investigated in the present work. The host material, WO 3 films, has been prepared from an ethanolic acetylated peroxotungstic acid sol containing 5 wt.% oxalic acid dehydrate (OAD) by sol-gel technique. The monoclinic structure and textured nature change of the films with the temperature increasing have been investigated by X-ray diffraction analysis. The surface morphology evolution of the films has been characterized by SEM. The shift in absorption edge towards the higher wavelength region observed from optical studies may be due to the electron scattering effects and the optical band filling effect that reveals the crystallization of the film. The amorphous film shows better optical modulation (ΔT = 76.9% at λ = 610 nm), fast color-bleach kinetics (t c ∼ 4 s and t b ∼ 9 s) and good reversibility (Q b /Q c = 90%), thereby rendering it suitable for smart window applications.

SYNTHESıS OF A NEW ELECTROCHROMıC POLYMER BASED ON TETRAPHENYLETHYLENE CORED TETRAKıS CARBAZOLE COMPLEX AND ıTS ELECTROCHROMıC DEVıCE APPLıCATıON

International Nuclear Information System (INIS)

Carbas, Buket Bezgin; Odabas, Serhat; Türksoy, Figen; Tanyeli, Cihangir

2016-01-01

Highlights: • A novel tetraphenylethylene containing tetrakis carbazole electropolymerized polymer was synthesized. • The polymer displayed transparent colored to dark green coloration upon oxidation. • A neutral state colorless electrochromic device was constructed. - Abstract: Poly-1,1,2,2-tetrakis(4-9H-carbazol-9-yl)phenyl)ethene P(TCP) was successfully synthesized by electrochemical oxidation of corresponding monomer, namely, 1,1,2,2-tetrakis(4-9H-carbazol-9-yl)phenyl)ethene (TCP) using dichloromethane as the solvent and tetrabutylammonium hexafluorophosphate (TBAPF 6 ) as supporting electrolyte. Spectroelectrochemical properties of P(TCP) were investigated in situ recording the electronic absorption spectra of the polymer film coated on indium-tin oxide (ITO) at various potentials. P(TCP) displayed transparent to military green color in 1.80 s with an optical contrast of 23.0% (at 770 nm) and an optical band gap of 3.1 eV. The objective evaluation of the colors of P(TCP) at various potentials was performed through colorimetry studies on the basis of “Commission Internationale de l′Eclairage” (CIE) standards. The morphology of the polymer film was investigated by AFM analysis. A dual type electrochromic device based on P(TCP) was constructed and its spectroelectrochemical properties were investigated. The electrochromic device exhibits color change from transparent to dark blue with a good open circuit memory.

How do 10-camphorsulfonic acid, silver or aluminum nanoparticles influence optical, electrochemical, electrochromic and photovoltaic properties of air and thermally stable triphenylamine-based polyazomethine with carbazole moieties?

International Nuclear Information System (INIS)

Iwan, Agnieszka; Boharewicz, Bartosz; Tazbir, Igor; Filapek, Michal; Korona, Krzysztof P.; Wróbel, Piotr; Stefaniuk, Tomasz; Ciesielski, Arkadiusz; Wojtkiewicz, Jacek; Wronkowska, Aleksandra A.; Wronkowski, Andrzej; Zboromirska-Wnukiewicz, Beata; Grankowska-Ciechanowicz, Sylwia; Kaminska, Maria; Szoplik, Tomasz

2015-01-01

Organic (10-camphorsulfonic acid, CSA), organic-inorganic (Ag-poly(vinylpyrrolidone), Ag-PVP with 10 and 20 nm size of Ag) or inorganic (Al, 18 nm) compounds were applied as new components of active layer in bulk heterojunction polymer solar cells based on a new polyazomethine (PAZ-Car-TPA) resulting in significant change of optical and electrical properties. Moreover, colloidal Ag (100 nm) and Ag-PVP in aqueous solution (10 nm) were tested as an addition to the hole transporting layer based on PEDOT:PSS in polyazomethine solar cells. CSA added to PAZ-Car-TPA decrease its energy gap from 1.91 to 1.20 eV and causes a significant bathochromic shift of the maximum of absorption band along with the change of the polymer color from yellow to red (electrochromic behavior). Photoluminescence maximum of PAZ-Car-TPA protonated with CSA showed 120 nm redshift from 500 to 620 nm in comparison to undoped PAZ-Car-TPA. HOMO-LUMO of PAZ-Car-TPA and its mixture with CSA were analyzed by cyclic voltammetry and quantum mechanical calculations using Density Functional Theory method. Refraction index and extinction coefficient of PAZ-Car-TPA and its mixtures with PC 71 BM as well as Ag or Al nanoparticles were investigated taking into consideration various thickness of polymer layer. The power conversion efficiency of the ITO/PEDOT:PSS/PAZ-Car-TPA:PCBM:CSA/Al device was five time higher than that of the device based on PAZ-Car-TPA:PCBM. Such an enhancement was found to be primarily due to the increase of the short-circuit current, suggesting that the charge collection increases upon the incorporation of CSA in the active layer. Moreover, presence of Ag-PVP (20 nm) or Al (18 nm) in device increased short circuit current of the constructed polymer solar cells. Additionally, devices were tested by external quantum efficiency measurements and electrochemical impedance spectroscopy in dark and under illumination. The polymer solar cell with PAZ-Car-TPA as donor in active layer showed good

Thermal Control Nano-Sat, Phase II

Data.gov (United States)

National Aeronautics and Space Administration — Based on successful space testing onboard the Midstar1 satellite, Eclipse Electrochromics have been identified by a number of organizations as well as NASA as a high...

Thermal Control Nano-Sat, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Based on successful space testing onboard the Midstar1 satellite, Eclipse Electrochromics have been identified by a number of organizations as well as NASA as a high...

Molecular Design of Semiconducting Polymers for High-Performance Organic Electrochemical Transistors

KAUST Repository

Nielsen, Christian B.; Giovannitti, Alexander; Sbircea, Dan-Tiberiu; Bandiello, Enrico; Niazi, Muhammad Rizwan; Hanifi, David A.; Sessolo, Michele; Amassian, Aram; Malliaras, George G.; Rivnay, Jonathan; McCulloch, Iain

2016-01-01

required for accumulation mode OECT operation. We discuss key aspects relating to OECT performance such as ion and hole transport, elec-trochromic properties, operational voltage and stability. The demonstration of our molecular design strategy

2 modified electrodes—electrooxidation of borohydride as probe

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science; Volume 37; Issue 3 ... Immobilization of redox species like Ni(OH)2 onto the electrode surface is important in the ... areas such as super capacitor, electrochromic displays and electrocatalysis.

Electrochemical performance of electroactive poly(amic acid)-Cu{sup 2+} composites

Energy Technology Data Exchange (ETDEWEB)

Yan, Ying [Alan G. MacDiarmid Institute, College of Chemistry, Jilin University, Changchun, 130012 (China); Li, Fangfei [State Key Lab of Superhard Materials, Jilin University, Changchun 130012 (China); Hanlon, Ashley M.; Berda, Erik B. [Department of Chemistry and Materials Science Program, University of New Hampshire, Durham, New Hampshire 03824 (United States); Liu, Xincai; Wang, Ce [Alan G. MacDiarmid Institute, College of Chemistry, Jilin University, Changchun, 130012 (China); Chao, Danming, E-mail: chaodanming@jlu.edu.cn [Alan G. MacDiarmid Institute, College of Chemistry, Jilin University, Changchun, 130012 (China)

2017-01-15

Graphical abstract: Electroactive poly(amic acid)-Cu{sup 2+} (EPAA-Cu) composites on the substrates have been prepared, whose electrochemical properties, including electroactivity, electrochromism and anticorrosion, reveal drastic enhancement after incorporation of Cu{sup 2+} ions. - Highlights: • The electroactive poly(amic acid)-Cu{sup 2+} (EPAA-Cu) composites were prepared. • A significant current enhancement phenomenon of EPAA-Cu/ITO electrodes was observed. • EPAA-Cu/ITO electrochromic electrodes reveals a shorter switching times. • Excellent corrosive protection for the CS was achieved by incorporating Cu{sup 2+} ions. - Abstract: Electroactive poly(amic acid)-Cu{sup 2+} (EPAA-Cu) composites on substrates were successfully prepared via nucleophilic polycondensation followed by the use of an immersing method. Analysis of the structure properties of EPAA-Cu composites was performed using scanning electron microscopy (SEM), X-ray photoelectron spectra (XPS) and Fourier-transform infrared spectra (FTIR). A significant current enhancement phenomenon of EPAA-Cu/ITO electrodes was found as evident from cyclic voltammetry (CV) measurements. In addition, Cu{sup 2+} ions were incorporated into the composites and had a positive effect on their electrochromic behaviors decreasing their switching times. The anticorrosive performance of EPAA-Cu composites coatings on the carbon steel in 3.5 wt% NaCl solution were also investigated in detail using tafel plots analysis and electrochemical impedance spectroscopy. The anticorrosive ability of these coatings significantly enhanced through the incorporation of Cu{sup 2+} ions.

Surface confined assemblies and polymers for sensing and molecular logic

Science.gov (United States)

de Ruiter, Graham; Altman, Marc; Motiei, Leila; Lahav, Michal; van der Boom, Milko E.

2013-05-01

Since the development of molecule-based sensors and the introduction of molecules mimicking the behavior of the AND gate in solution by de Silva in 1993, molecular (Boolean) Logic and Computing (MBLC) has become increasingly popular. The molecular approach toward Boolean logic resulted in intriguing proofs of concepts in solution including logic gates, half-adders, multiplexers, and flip-flop logic circuits. Molecular assemblies can perform diverse logic tasks by reconfiguring their inputs. Our recent research activities focus on MBLC with electrochromic polymers and immobilized polypyridyl complexes on solid support. We have designed a series of coordination-based thin films that are formed linearly by stepwise wet-chemical deposition or by self-propagating molecular assembly. The electrochromic properties of these films can be used for (i) detecting various analytes in solution and in the air, (ii) MBLC, (iii) electron-transfer studies, and (iv) interlayers for efficient inverted bulk-heterojunction solar cells. Our concept toward MBLC with functionalized surfaces is applicable to electrochemical and chemical inputs coupled with optical readout. Using this approach, we demonstrated various logic architectures with redox-active functionalized surfaces. Electrochemically operated sequential logic systems (e.g., flip-flops), multi-valued logic, and multi-state memory have been designed, which can improve computational power without increasing spatial requirements. Applying multi-valued digits in data storage and information processing could exponentially increase memory capacity. Our approach is applicable to highly diverse electrochromic thin films that operate at practical voltages (< 1.5 V).

PEO nanocomposite polymer electrolyte for solid state symmetric ...

Indian Academy of Sciences (India)

cells/supercapacitors) to electro-chromic displays, smart windows and ... electrolytes and their usage in lithium ion rechargeable solid state batteries are well .... the experimental plot using the Arrhenius relationship σ = σ0exp(−Ea/kT) where ...

Electrochemical synthesis and characterization of chloride doped ...

Indian Academy of Sciences (India)

Unknown

cations in rechargeable batteries, corrosion protection, light emitting diodes, molecular sensors, electrochromic devices and microwave screening (Inzelt et al 2001). Polyaniline is not charge conjugation symmetric, i.e. the valence and conduction bands are asymmetric to a great extent (Ghos et al 2001). A partial oxidation ...

DC conductivity and spectroscopic studies of polyaniline doped with ...

Indian Academy of Sciences (India)

They have wide applications in devices such as solar cells, rechargeable batteries, light emitting diodes, micro- actuators, electrochromic displays, field effect transistors, sensors etc (Saraswathi et al 1999). In polymers, doping can be carried out by different pro- cesses such as chemical and electrochemical. Recently, metal.

Smart responsive phosphorescent materials for data recording and security protection.

Science.gov (United States)

Sun, Huibin; Liu, Shujuan; Lin, Wenpeng; Zhang, Kenneth Yin; Lv, Wen; Huang, Xiao; Huo, Fengwei; Yang, Huiran; Jenkins, Gareth; Zhao, Qiang; Huang, Wei

2014-04-07

Smart luminescent materials that are responsive to external stimuli have received considerable interest. Here we report ionic iridium (III) complexes simultaneously exhibiting mechanochromic, vapochromic and electrochromic phosphorescence. These complexes share the same phosphorescent iridium (III) cation with a N-H moiety in the N^N ligand and contain different anions, including hexafluorophosphate, tetrafluoroborate, iodide, bromide and chloride. The anionic counterions cause a variation in the emission colours of the complexes from yellow to green by forming hydrogen bonds with the N-H proton. The electronic effect of the N-H moiety is sensitive towards mechanical grinding, solvent vapour and electric field, resulting in mechanochromic, vapochromic and electrochromic phosphorescence. On the basis of these findings, we construct a data-recording device and demonstrate data encryption and decryption via fluorescence lifetime imaging and time-gated luminescence imaging techniques. Our results suggest that rationally designed phosphorescent complexes may be promising candidates for advanced data recording and security protection.

Intercalation compounds of vanadium pentoxide hydrated with metalporphyrins and lanthanide ions

International Nuclear Information System (INIS)

Oliveira, Herenilton Paulino

1994-01-01

The lamellar structure of the vanadium pentoxide matrix allows the intercalation of organic molecules, ions and conductor polymers. It is important to emphasize that the vanadium oxide matrix is an intrinsic semiconductor and presents electrochromic properties. In the beginning of this work the method of synthesis and the electrochemical and electrochromic properties were extensively explored. The effect of alkaline metal and lanthanide ions on the structure of vanadium oxide matrix was studied by X-ray and infrared spectroscopy. Moreover, the influence of those ions in the electrochemical, spectro electrochemical and magnetic properties were studied. Finally, some intercalation compounds containing porphyrins were prepared and characterized by elemental analysis, X-ray diffraction, and electronic, vibrational, Moessbauer and X-ray fluorescence spectroscopy. The electrochemical and spectro electrochemical properties were investigated. And the performance of an iron porphyrin based intercalation compound as catalyst for molecular oxygen reduction was evaluated using the rotating ring-disc electrode technique. (author)

Multichromic Polymers Containing Alternating Bi(3-Methoxythiophene and Triphenylamine Based Units with Para-Protective Substituents

Directory of Open Access Journals (Sweden)

Yingfei Hou

2016-09-01

Full Text Available Two novel triphenylamine-based thiophene derivative monomers, 4-cyano-4′,4″-di(4-methoxythiophen-2-yltriphenylamine and 4-methoxy-4′,4″-di(4-methoxythiophen-2-yltriphenylamine, were successfully synthesized. The corresponding polymers including poly (4-cyano-4′,4″-di(4-methoxythiophen-2-yltriphenylamine and poly (4-methoxy-4′,4″-di(4-methoxythiophen-2-yltriphenylamine were electrochemically synthesized and characterized by multiple test method. The electrochemical measurements and spectroelectrochemical analyses revealed that both of the two polymers had quasi-reversible redox behavior and multi-electrochromic properties. The two polymer films showed reversible electrochemical oxidation, excellent optical contrasts in NIR region (62% at 1070 nm for the first polymer, and 86% at 1255 nm for the second polymer, satisfactory coloration efficiencies and fast switching times. The research on the application of the as prepared polymer in the fabrication of electrochromic device was also conducted, employing PCMTPA or PMMTPA as the anodically coloring materials.

WO{sub 3} nanorods prepared by low-temperature seeded growth hydrothermal reaction

Energy Technology Data Exchange (ETDEWEB)

Ng, Chai Yan [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Abdul Razak, Khairunisak, E-mail: khairunisak@eng.usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); NanoBiotechnology Research and Innovation (NanoBRI), Institute for Research in Molecular Medicine (INFORMM), Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lockman, Zainovia, E-mail: zainovia@eng.usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

2014-03-05

Highlights: • WO{sub 3} nanorods with 5–10 nm diameter were grown directly on seeded tungsten foil. • WO{sub 3} nanorods were successfully grown at low temperature of 80 °C. • WO{sub 3} nanorods were grown on the entire surface of the seed layer after 24 h. • Annealed nanorods showed better electrochromic properties than as-made nanorods. -- Abstract: This work describes the first tungsten oxide (WO{sub 3}) nanorods hydrothermally grown on W foil. WO{sub 3} nanorods were successfully grown at low hydrothermal temperature of 80 °C by seeded growth hydrothermal reaction. The seed layer was prepared by thermally oxidized the W foil at 400 °C for 0.5 h. This work discusses the effect of hydrothermal reaction and annealing period on the morphological, structural, and electrochromic properties of WO{sub 3} nanorods. Various hydrothermal reaction periods (8–24 h) were studied. Monoclinic WO{sub 3} nanorods with 5–10 nm diameter were obtained after hydrothermal reaction for 24 h. These 24 h WO{sub 3} nanorods were also annealed at 400 °C with varying dwelling periods (0.5–4 h). Electrochromic properties of WO{sub 3} nanorods in an acidic electrolyte were analyzed using cyclic voltammetry and UV–vis spectrophotometry. WO{sub 3} nanorods annealed at 400 °C for 1 h showed the highest charge capacity and the largest optical contrast among the 24 h WO{sub 3} films. The sample also showed good cycling stability without significant degradation. Based on the results, the reaction mechanism of WO{sub 3} nanorod formation on W foil was proposed.

RF power dependent formation of amorphous MoO3-x nanorods by RF magnetron sputtering

International Nuclear Information System (INIS)

Navas, I.; Vinodkumar, R.; Detty, A.P.; Mahadevan Pillai, V.P.

2009-01-01

Full text: The fabrication of nanorods has received increasing attention for their unique physical and chemical properties and a wide range of potential applications such as photonics and nanoelectronics Molybdenum oxide nanorods with high activity can be used in a wide variety of applications such as cathodes in rechargeable batteries, field emission devices, solid lubricants, superconductors thermoelectric materials, and electrochromic devices. In this paper, amorphous MoO 3-x nanorods can find excellent applications in electrochromic and gas sensing have been successfully prepared by varying the R F power in R F Magnetron Sputtering system without heating the substrate; other parameters which are optimised in our earlier studies. We have found that the optimum RF power for nanorod formation is 200W. At a moderate RF power (200W), sputtering redeposition takes places constructively which leads to formation of fine nanorods. Large RF power creates high energetic ion bombardment on the grains surfaces which can lead to re-nucleation, so the grains become smaller and columnar growth is interrupted. Beyond the RF power 200W, the etching effect of the plasma became more severe and damaged the surface of the nanorods. All the molybdenum oxide films prepared are amorphous; the XRD patterns exhibit no characteristic peak corresponds to MoO 3 . The amorphous nature is preferred for good electrochromic colouration The spectroscopic properties of the nanorods have been investigated systematically using atomic force microscopy, x-ray diffraction, micro-Raman, UV-visible and photoluminescence (PL) spectroscopy. The films exhibit two emission bands; a near band edge UV emission and a defect related deep level visible emission

Room temperature ferromagnetic and photoluminescence ...

Indian Academy of Sciences (India)

32

electrode, photo electronic devices, photo sensors, liquid crystal displays, electrochromic windows, solar panels and transparent coatings for solar-energy heat mirrors [11-13]. Here we report on magnetic properties of ITO nanoparticles at room temperature and at 100 K. 2. Experimental. The In1.9Sn0.1O3 powder samples ...

New Electronic Technology Applied in Flexible Organic Optical System

Directory of Open Access Journals (Sweden)

Andre F. S. Guedes

2014-02-01

Full Text Available The synthesis and application of new organic materials, nanostructured, for developing technology based on organic devices, have been the main focus of the scientific community. In recent years, the first polymeric electronics products have entered the market (organic semiconductor materials and there are some electrochromic devices among them that have been called smart windows, once they control the passage of light or heat through a closed environment as an ordinary window. The main functional aspect of electrochromic devices, when being used in architectural and automotive industry, is to control the passage of light and temperature with thermal and visual comfort. These devices can be flexible and very thin, not containing heavy metals, and formed by layers of organic material deposited in several architectures. In this study, the electro-deposition of organic materials in the Polyaniline, PANI case, which provide stability in optical and electrical parameters, was utilized with the means of developing prototypes of organic electrochromic devices. These materials were characterized by: ultraviolet-visible spectroscopy absorption (UV-Vis, measurement of thickness (MT and electrical measurements (EM. This study aims to establish the relationship between the thickness of the active layer and the value of the electrical resistivity of the layer deposited through an electro-deposition technique. The experimental results enabled the equating of the electrical resistivity related to the thickness of the deposited layer. The linear fit of these results has expressed the thickness of the conducting layer, α, and the lowest value of the electrical resistivity, β, associated with the gap between the valence band and the conduction band. Thus, the results have demonstrated that, when the layer of organic material is completely conductive, we may obtain the thickness of the organic material deposited on the substrate.

End-group-directed self-assembly of organic compounds useful for photovoltaic applications

Science.gov (United States)

Beaujuge, Pierre M.; Lee, Olivia P.; Yiu, Alan T.; Frechet, Jean M.J.

2016-05-31

The present invention provides for an organic compound comprising electron deficient unit covalently linked to two or more electron rich units. The present invention also provides for a device comprising the organic compound, such as a light-emitting diode, thin-film transistor, chemical biosensor, non-emissive electrochromic, memory device, photovoltaic cells, or the like.

Conjugated and fluorescent polymer based on dansyl-substituted pyrrole prepared by electrochemical polymerization in acetonitrile containing boron trifluoride diethyl etherate

International Nuclear Information System (INIS)

Almeida, Andresa K.A.; Dias, Jéssica M.M.; Silva, Ana Julia C.; Santos, Diego P.; Navarro, Marcelo; Tonholo, Josealdo; Goulart, Marília O.F.; Ribeiro, Adriana S.

2014-01-01

Graphical abstract: - Highlights: • A fluorescent pyrrole derivative bearing a dansyl substituent (PyPDG) was synthesized. • PyPDG was electropolymerized onto ITO in (C 4 H 9 ) 4 NBF 4 /CH 3 CN/BFEE mixed electrolyte. • The resulting polymer (PPyPDG) films displayed electrochromic behavior. • PPyPDG is a good green light emitter material. - Abstract: A fluorescent pyrrole derivative bearing a dansyl substituent was prepared by a simple synthetic route and electropolymerized onto Indium Tin Oxide (ITO) electrodes. The presence of the dansyl group in the monomer precursor prevents the electropolymerization in usual systems, such as (C 4 H 9 ) 4 NBF 4 in acetonitrile (CH 3 CN). For this reason, it was added 20% boron trifluoride diethyl etherate (BFEE) to this system, to achieve electropolymerization. The resulting poly[3-(N-pyrrolyl)propyl dansylglycinate] (PPyPDG) films displayed electrochromic behavior. Their color varied from greenish-yellow, in the neutral state, to greyish-green, in the oxidized state; moreover PPyPDG is a good green light emitter material. Therefore, PPyPDG films might be potentially applicable in displays and optoelectronic devices

Preparation, structure, and unique redox properties of mono-, bis-, and Tris(diarylmethylene)-1,3,5-trithianes and related compounds

Science.gov (United States)

Suzuki; Yoshino; Nishida; Ohkita; Tsuji

2000-09-08

A series of 1,3,5-trithianes 1-3 having diarylmethylene units were designed as novel electron donors giving highly colored cationic species upon oxidation. They were prepared along with the dithiane and dithiazine derivatives 4-6 by the reactions of lithiated heterocycles with diaryl ketones followed by dehydration. Voltammetric analyses indicate that a large structural change and/or transannular bonding are induced during their electrochemical oxidation. Mono(diarylmethylene) derivative 1a exhibits electrochromism with vivid change in color from faintly yellow to deep blue with concomitant rotation around the exocyclic bond. Both of the strongly colored salts obtained upon oxidation of 2,4-bis- and 2,4,6-tris(diarylmethylene)-1,3,5-trithianes (2aa and 3) consist of the dications with a 1,2,4-trithiane ring, suggesting the easy skeletal rearrangement of the transannular dications with a trithiabicylo[3.1.0]hexane ring. Upon reduction of these salts were obtained bright yellow 12 and 13, respectively, with high electron-donating properties due to the tetraarylbutadiene-type conjugation, thus giving another class of electrochromic compounds.

Fast Switching ITO Free Electrochromic Devices

DEFF Research Database (Denmark)

Jensen, Jacob; Hösel, Markus; Kim, Inyoung

2014-01-01

devices with a response time of 2 s for an optical contrast of 27%. The other design utilizes an embedded silver grid electrode whereupon response times of 0.5 s for a 30% optical contrast are realized when oxidizing the device. A commercially available conductive poly(3,4-ethylenedioxythiophene):poly(4...

Simple One-Step Method to Synthesize Polypyrrole-Indigo Carmine-Silver Nanocomposite

OpenAIRE

Loguercio, Lara Fernandes; Demingos, Pedro; Manica, Luiza de Mattos; Griep, Jordana Borges; Santos, Marcos José Leite; Ferreira, Jacqueline

2016-01-01

A nanocomposite of indigo carmine doped polypyrrole/silver nanoparticles was obtained by a one-step electrochemical process. The nanocomposite was characterized by scanning electron microscopy, infrared spectroscopy, ultraviolet-visible-near infrared spectroscopy, and cyclic voltammetry. The simple one-step process allowed the growth of silver nanoparticles during the polymerization of polypyrrole, resulting in films with electrochromic behavior and improved electroactivity. In addition, poly...

V M Gurame

Indian Academy of Sciences (India)

Home; Journals; Bulletin of Materials Science. V M Gurame. Articles written in Bulletin of Materials Science. Volume 38 Issue 2 April 2015 pp 483-491. Spray deposited CeO2–TiO2 counter electrode for electrochromic devices · A K Bhosale S R Kulal V M Gurame P S Patil · More Details Abstract Fulltext PDF. Optically ...

Synthesis of Oxidation-Resistant Cupronickel Nanowires for Transparent Conducting Nanowire Networks

Energy Technology Data Exchange (ETDEWEB)

Rathmall, Aaron [Duke University; Nguyen, Minh [Duke University; Wiley, Benjamin J [Duke University

2012-01-01

Nanowires of copper can be coated from liquids to create flexible, transparent conducting films that can potentially replace the dominant transparent conductor, indium tin oxide, in displays, solar cells, organic light-emitting diodes, and electrochromic windows. One issue with these nanowire films is that copper is prone to oxidation. It was hypothesized that the resistance to oxidation could be improved by coating copper nanowires with nickel. This work demonstrates a method for synthesizing copper nanowires with nickel shells as well as the properties of cupronickel nanowires in transparent conducting films. Time- and temperature-dependent sheet resistance measurements indicate that the sheet resistance of copper and silver nanowire films will double after 3 and 36 months at room temperature, respectively. In contrast, the sheet resistance of cupronickel nanowires containing 20 mol % nickel will double in about 400 years. Coating copper nanowires to a ratio of 2:1 Cu:Ni gave them a neutral gray color, making them more suitable for use in displays and electrochromic windows. These properties, and the fact that copper and nickel are 1000 times more abundant than indium or silver, make cupronickel nanowires a promising alternative for the sustainable, efficient production of transparent conductors.

Nanocomposite Prepared from In Situ Grafting of Polypyrrole to Aminobenzoyl-Functionalized Multiwalled Carbon Nanotube and Its Electrochemical Properties

Science.gov (United States)

2011-01-01

variety of poten- tial applications such as electrically conducting composites,6 actuators,7,8 supercapacitors,9 and electrochromic10 and photo- voltaic11...received much interest for their uses in fabricating a new class of advanced materials because of their unique structural , mechanical, and electrical...the supporting polymer matrices and interfacial interactions between them should be addressed first. Hence, harsh chemical treatments in strong acids

GISAXS view of induced morphological changes in nanostructured CeVO [sub] 4 thin films

OpenAIRE

Lučić Lavčević, Magdi; Dubček, Pavo; Bernstorff, Sigrid; Turković, Aleksandra; Orel, Bojan; Crnjak Orel, Zorica

2015-01-01

Nanostructured CeVO4 films, designed for applications in electrochemical cells and electrochromic devices, were obtained on glass substrates by the sol-gel process. An analysis of morphological modifications in these films, induced by ultrasonication, annealing, and introduction of lithium ions, was performed, using the grazing-incidence small-angle X-ray scattering technique (GISAXS). The GISAXS results are discussed and related with complementary examinations of the same films in real space...

The effect of changes in π-conjugated terthienyl systems using thienyl and ethylenedioxybenzene functionalized thieno[3,4-b]pyrazine precursors: Multicolored low band gap polymers

International Nuclear Information System (INIS)

Tarkuc, Simge; Unver, Elif Kose; Udum, Yasemin Arslan; Tanyeli, Cihangir; Toppare, Levent

2010-01-01

New classes of thieno[3,4-b]pyrazines containing thienyl and ethylenedioxy phenyl units on electron-withdrawing moieties of π-conjugated terthienyl were synthesized. The effect of structural differences on electrochemical and optoelectronic properties of the resulting polymers was investigated. Changes in the electronic nature of the functional groups enable to tune the electrochemical properties of the π-conjugated terthienyl monomers by lowering oxidation potential from 0.62 V (DTTP) to 0.56 V (DBTP). Spectroelectrochemical analyses revealed that the neutral polymer (PDBTP) is dark green in its neutral state revealing π-π* transitions in two well-separated bands at 410 and 751 nm. The electronic band gap of polymer, defined as the onset of the π-π* transition, is found to be 1.0 eV. Using the thienyl unit instead of ethylenedioxy phenyl, a red shift in the band gap (0.95 eV) is observed. The polymer, PDTTP, exhibits multicolor electrochromism and can be switched between a dark yellow neutral state, a green intermediate state, and a brown oxidized state. PDBTP also shows a multicolored electrochromic behavior with three distinct states: dark green at the neutral state, a brown intermediate state, and a brown-violet oxidized state.

Nanocrystalline sol-gel Nb{sub 2}O{sub 5} coatings. Preparation, characterisation and application to photovoltaic cell, lithium battery and eletrochromic device

Energy Technology Data Exchange (ETDEWEB)

Guo, Yeping

2002-07-01

Thick and thin films of Nb{sub 2}O{sub 5} have been prepared by the sol-gel process using cheap niobium pentachloride as precursor and a new synthesis route. The microstructure of the films was tailored by adding poly(ethylene glycol) (PEG) and carbon soot into the sol and varying the sintering temperature. The thesis describes the properties of the sols and their influence on the properties of the resulting nanocrystalline Nb{sub 2}O{sub 5} films as electrodes in dye sensitised solar cells, electrochromic devices and rechargeable lithium batteries. A solar light-to-electric conversion efficiency of Ru(II) sensitised Nb{sub 2}O{sub 5} solar cell as high as 7% under 120 W/m{sup 2} illumination was obtained. An equivalent electric circuit of the dye sensitised electrode/electrolyte interface based on the electrochemical impedance spectroscopy was modelled and found to fit all the results. The values obtained for the electric elements from the simulation of the results were found to relate material parameters to the cell performance and their influence on the cell performance are illustrated. The electrochromism and Li{sup +}-charge and discharge of the Nb{sub 2}O{sub 5} films exhibited also good performance. (orig.)

Thermal oxidation of seeds for the hydrothermal growth of WO3 nanorods on ITO glass substrate

International Nuclear Information System (INIS)

Ng, Chai Yan; Abdul Razak, Khairunisak; Lockman, Zainovia

2015-01-01

This work reports a simple seed formation method for the hydrothermal growth of tungsten oxide (WO 3 ) nanorods. A WO 3 seed layer was prepared by thermal oxidation, where a W-sputtered substrate was heated and oxidized in a furnace. Oxidation temperatures and periods were varied at 400–550 °C and 5–60 min, respectively, to determine an appropriate seed layer for nanorod growth. Thermal oxidation at 500 °C for 15 min was found to produce a seed layer with sufficient crystallinity and good adhesion to the substrate. These properties prevented the seed from peeling off during the hydrothermal process, thereby allowing nanorod growth on the seed. The nanorod film showed better electrochromic behavior (higher current density of − 1.11 and + 0.65 mA cm −2 ) than compact film (lower current density of − 0.54 and + 0.28 mA cm −2 ). - Highlights: • A simple seed formation method (thermal oxidation) on sputtered W film is reported. • Crystalline seed with good adhesion to substrate is required for nanorod growth. • The appropriate temperature and period for seed formation were 500 °C and 15 min. • WO 3 nanorods exhibited higher electrochromic current density than WO 3 compact film.

Thermal oxidation of seeds for the hydrothermal growth of WO{sub 3} nanorods on ITO glass substrate

Energy Technology Data Exchange (ETDEWEB)

Ng, Chai Yan [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); Department of Mechanical and Material Engineering, Lee Kong Chian Faculty of Engineering and Science, Universiti Tunku Abdul Rahman, Jalan Sungai Long, Bandar Sungai Long, Cheras, 43000 Kajang, Selangor (Malaysia); Abdul Razak, Khairunisak, E-mail: khairunisak@usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia); NanoBiotechnology Research and Innovation (NanoBRI), Institute for Research in Molecular Medicine (INFORMM), Universiti Sains Malaysia, 11800 USM, Penang (Malaysia); Lockman, Zainovia, E-mail: zainovia@usm.my [School of Materials and Mineral Resources Engineering, Universiti Sains Malaysia, 14300 Nibong Tebal, Penang (Malaysia)

2015-11-30

This work reports a simple seed formation method for the hydrothermal growth of tungsten oxide (WO{sub 3}) nanorods. A WO{sub 3} seed layer was prepared by thermal oxidation, where a W-sputtered substrate was heated and oxidized in a furnace. Oxidation temperatures and periods were varied at 400–550 °C and 5–60 min, respectively, to determine an appropriate seed layer for nanorod growth. Thermal oxidation at 500 °C for 15 min was found to produce a seed layer with sufficient crystallinity and good adhesion to the substrate. These properties prevented the seed from peeling off during the hydrothermal process, thereby allowing nanorod growth on the seed. The nanorod film showed better electrochromic behavior (higher current density of − 1.11 and + 0.65 mA cm{sup −2}) than compact film (lower current density of − 0.54 and + 0.28 mA cm{sup −2}). - Highlights: • A simple seed formation method (thermal oxidation) on sputtered W film is reported. • Crystalline seed with good adhesion to substrate is required for nanorod growth. • The appropriate temperature and period for seed formation were 500 °C and 15 min. • WO{sub 3} nanorods exhibited higher electrochromic current density than WO{sub 3} compact film.

Modification of the Properties of Vanadium Oxide Thin Films by Plasma-Immersion Ion Implantation

Directory of Open Access Journals (Sweden)

Sergey Burdyukh

2018-01-01

Full Text Available The paper describes the effect of doping with hydrogen and tungsten by means of plasma-immersion ion implantation (PIII on the properties of vanadium dioxide and hydrated vanadium pentoxide films. It is shown that the parameters of the metal-insulator phase transition in VO2 thin films depend on the hydrogen implantation dose. Next, we explore the effect of PIII on composition, optical properties, and the internal electrochromic effect (IECE in V2O5·nH2O films. The variations in the composition and structure caused by the hydrogen insertion, as well as those caused by the electrochromic effect, are studied by nuclear magnetic resonance, thermogravimetry, Raman spectroscopy, and X-ray structural analysis. It is shown that the ion implantation-induced hydrogenation can substantially enhance the manifestation and performance of the IECE in V2O5 xerogel films. Finally, the effect of PIII-assisted doping with W on the parameters of electrical switching in Au/V2O5·nH2O/Au sandwich structures is examined. It is shown that implanting small tungsten doses improves the switching parameters after forming. When implanting large doses, switching is observed without electroforming, and if electroforming is applied, the switching effect, on the contrary, disappears.

Changes in H(+)-ATP Synthase Activity, Proton Electrochemical Gradient, and pH in Pea Chloroplast Can Be Connected with Variation Potential.

Science.gov (United States)

Sukhov, Vladimir; Surova, Lyubov; Morozova, Ekaterina; Sherstneva, Oksana; Vodeneev, Vladimir

2016-01-01

Local stimulation induces generation and propagation of electrical signals, including the variation potential (VP) and action potential, in plants. Burning-induced VP changes the physiological state of plants; specifically, it inactivates photosynthesis. However, the mechanisms that decrease photosynthesis are poorly understood. We investigated these mechanisms by measuring VP-connected systemic changes in CO2 assimilation, parameters of light reactions of photosynthesis, electrochromic pigment absorbance shifts, and light scattering. We reveal that inactivation of photosynthesis in the pea, including inactivation of dark and light reactions, was connected with the VP. Inactivation of dark reactions decreased the rate constant of the fast relaxation of the electrochromic pigment absorbance shift, which reflected a decrease in the H(+)-ATP synthase activity. This decrease likely contributed to the acidification of the chloroplast lumen, which developed after VP induction. However, VP-connected decrease of the proton motive force across the thylakoid membrane, possibly, reflected a decreased pH in the stroma. This decrease may be another mechanism of chloroplast lumen acidification. Overall, stroma acidification can decrease electron flow through photosystem I, and lumen acidification induces growth of fluorescence non-photochemical quenching and decreases electron flow through photosystem II, i.e., pH decreases in the stroma and lumen, possibly, contribute to the VP-induced inactivation of light reactions of photosynthesis.

Fiscal 1994 report on technological results. Technological development for putting solar system to practical use such as industrial use / Development of advanced heat process type system / Development of solar thermal refrigeration system; 1994 nendo sangyoyo solar system jitsuyoka gijutsu kaihatsu / Advanced heat process gata system no kaihatsu / Taiyonetsu reito reizo system no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

A system is being developed for adjusting incident solar energy in accordance with objectives by using, as a window material, glass whose light transmittance is variable by the electrochromic color and bleach reaction. The target is a module which, having an area of 60x40 cm or larger, is capable of installation for a structural opening of a building, which has a practical service life (ten years outdoors), and which is provided with the range of visible transmittance of 50% or more with capability of continuous light adjustment. In fiscal 1994, a basic parameter was set for the production process of a large module, with the experimental production/evaluation conducted, and with an outlook formed for achieving the target. The device is basically composed of glass, transparent electrically conductive film, counter electrode, electrolyte, principal electrochromic film electrode, transparent conductive film, transparent resin film for sealing, and glass, with the total thickness 4 mm or above. The transparent conductive film in use is tin-based, the counter electrode is NiOx based in oxidation color-erasing type, the electrolyte is Sb{sub 2}O{sub 5}, and the principal electrode is WO{sub 3} based in reduction color-developing type. (NEDO)

In situ measurements of the optical absorption of dioxythiophene-based conjugated polymers

Science.gov (United States)

Hwang, J.; Schwendeman, I.; Ihas, B. C.; Clark, R. J.; Cornick, M.; Nikolou, M.; Argun, A.; Reynolds, J. R.; Tanner, D. B.

2011-05-01

Conjugated polymers can be reversibly doped by electrochemical means. This doping introduces new subband-gap optical absorption bands in the polymer while decreasing the band-gap absorption. To study this behavior, we have prepared an electrochemical cell allowing in situ measurements of the optical properties of the polymer. The cell consists of a thin polymer film deposited on gold-coated Mylar behind which is another polymer that serves as a counterelectrode. An infrared transparent window protects the upper polymer from ambient air. By adding a gel electrolyte and making electrical connections to the polymer-on-gold films, one may study electrochromism in a wide spectral range. As the cell voltage (the potential difference between the two electrodes) changes, the doping level of the conjugated polymer films is changed reversibly. Our experiments address electrochromism in poly(3,4-ethylenedioxythiophene) (PEDOT) and poly(3,4-dimethylpropylenedioxythiophene) (PProDOT-Me2). This closed electrochemical cell allows the study of the doping induced subband-gap features (polaronic and bipolaronic modes) in these easily oxidized and highly redox switchable polymers. We also study the changes in cell spectra as a function of polymer thickness and investigate strategies to obtain cleaner spectra, minimizing the contributions of water and gel electrolyte features.

Hybrid Co-deposition of Mixed-Valent Molybdenum-Germanium Oxides (MoxGeyOz): A Route to Tunable Optical Transmission (Postprint)

Science.gov (United States)

2015-08-05

within these films can be attrib- uted to low adatommobility related to the low deposition temperature (T ≤ 100 °C), interruption of film nucleation via...heating being applied to the substrate during deposition as well as the tendency of oxygen to act as a grain refining agent, interrupting nucleation ...heating and humidity : effect of Al oxide top coatings, Thin Solid Films 562 (2014) 568–573. [7] C. Granqvist, Electrochromic oxides: a bandstructure

Caracterizacion y optimizacion electroquimica de dispositivos electrocromicos duales basados en polimeros conductores

Science.gov (United States)

Padilla Martinez, Javier

The aim of this thesis is to emphasize the existing relations between electrochemical processes, or electrochemical magnitudes, and colour changes. The work is focused on two aspects: individual spectroelectrochemical characterization of the constituent materials followed by an electrochemical and optical study of the performance of the dual system constructed with those materials. The objective is the optimization of both electrochemical and optical processes in dual conducting polymer systems, obtaining experimental methodologies able to characterize, predict, and finally design optimal dual electrochromic devices. The first part of the study is focused on the development of the proper methodology to obtain an optical characterization of any electrochromic material as a function of its electrochemical properties. Materials used were poly((3,4-ethylenedioxy)thiophene) (PEDOT) and poly-(3,6-bis(2-(3,4-ethylenedioxy)thienyl)-N-methylcarbazole) (PBEDOT-NMCz). PEDOT films are coloured under reduction, while PBEDOT-NMCz are coloured under oxidation, showing complementary colouration, and so they can be used to construct a dual electrochromic device. Based on the obtained experimental results, a theoretical study was undertaken to establish the optical responses of a system comprising several electrochromic layers. The theoretically obtained relations were experimentally proved. Relations obtained allow the prediction of the maximum contrast configuration for a dual system, as a function of the individual electrochemical properties of each constituent material. The system studied was PEDOT/PBEDOT-NMCz. The third chapter deals with the proposal and development of a new experimental methodology able to register the individual oxidation states of each electrode during operation of a dual device, obtaining then direct information about device performance. This methodology allows the study of the influence of different physical and chemical variables, like ratio of redox

Hydrothermal synthesis of electrode materials pyrochlore tungsten trioxide film

Science.gov (United States)

Guo, Jingdong; Li, Yingjeng James; Stanley Whittingham, M.

Hydrothermal synthesis methods have been successfully used to prepare new transition-metal oxides for cathodes in electrochemical devices such as lithium batteries and electrochromic windows. The tungsten oxides were the first studied, but the method has been extended to the oxides of molybdenum, vanadium and manganese. Sodium tungsten oxide films with the pyrochlore structure have been prepared on gold/alumina and indium-doped tin oxide substrates. These films reversibly and rapidly intercalate lithium and hydrogen ions.

Materials science for solar energy conversion systems

CERN Document Server

Granqvist, CG

1991-01-01

Rapid advances in materials technology are creating many novel forms of coatings for energy efficient applications in solar energy. Insulating heat mirrors, selective absorbers, transparent insulation and fluorescent concentrators are already available commercially. Radiative cooling, electrochromic windows and polymeric light pipes hold promise for future development, while chemical and photochemical processes are being considered for energy storage. This book investigates new material advances as well as applications, costs, reliability and industrial production of existing materials. Each c

Oxygen partial pressure effects on the magnetron sputtered WO3 films

International Nuclear Information System (INIS)

Muğlu, G Merhan; Gür, E

2016-01-01

Electrochromism is changing color of a substance in response to the applied an external electric field and the phenomenon is reversible. WO 3 is very attractive material due to its electrochromic properties as well as it is also attractive for many different applications such as gas sensors, phosphorous screen, textile, glass industry. In this study, it is aimed to provide optimization of the optical and structural characteristics of WO 3 by changing the growth parameters mainly the oxygen partial pressure. The partial pressure of oxygen was changed with increments of 0.7 mTorr. For the analysis, X-ray Diffraction (XRD), absorption, Raman spectroscopy measurements were used. When O 2 gas increased, peaks belong to the WO 3 was observed in XRD patterns at the 2 theta angles of 23.0, 11.0, 23.5 and 28.5 angles corresponding to the (002), (020) and (220) planes, respectively. This shows that there is a significant effect of increasing O 2 partial pressure in the formation of WO 3 films. The bandgap energy of the WO 3 thin films are found to be around 3.0 eV. Raman measurements showed vibrational modes of W-O-W stretching and bending modes which shows small shifts depending on the partial pressures of the O 2 . Obtained results indicated that better crystal structure is obtained with higher O 2 gas partial pressure. (paper)

Fabry-Perot-like interference security image structures: From passive to active

International Nuclear Information System (INIS)

Baloukas, B.; Trottier-Lapointe, W.; Martinu, L.

2014-01-01

Counterfeiting of products and important documents is at an all-time high and is costing the world economy hundreds of billions of dollars yearly as well as posing significant safety and health hazards through the production of uncertified goods, e.g., pharmaceutical products. To limit these effects, interference-based optical security devices offering an angular color shift are still widely in use. Unfortunately, commercial iridescent materials are now readily available and represent a potential source of counterfeiting. In this short review, we first describe the basic principles behind passive interference security image structures (ISIS) and the qualities which have resulted in their integration into most important documents. Various features which have been added to ISIS in order to make them harder to duplicate yet simpler to authenticate are also presented (metamerism, magnetic materials, diffraction, etc.). We then address the implementation of active materials, mainly electrochromic WO 3 as a means of generating two-level authentication devices. Finally, we discuss some general considerations to keep in mind when developing features for security applications. - Highlights: • We review Fabry–Perot-like metal-dielectric filters used in optical security. • We discuss/demonstrate recent additions: metamerism, magnetism and diffraction. • We demonstrate a feature based on the use of thin metallic mirrors. • We cover recent developments in the use of active materials. • We demonstrate an electrochromic feature with two levels of authentication

A Modular Framework for 3 Way Electrochromic Switches

Science.gov (United States)

2017-09-01

1215 Jefferson Davis Highway, Suite 1204, Arlington, VA 22202‐ 4302.   Respondents should be aware that notwithstanding any other provision of  law ...A new hybrid exchange-correlation func- tional using the coulomb -attenuating method (CAM-B3LYP). Chem Phys Lett. 2004;393(1):51–57. 54. Hehre WJ

Development and Manufacture of Polymer-based Electrochromic Devices

DEFF Research Database (Denmark)

Jensen, Jacob; Hösel, Markus; Dyer, Aubrey L.

2015-01-01

-to-roll methods compatible with upscaling and manufacture. The successful approaches to operational devices are presented in detail, as well as areas where future research would have a high impact and accelerate the development such as highly conducting and transparent substrates, electrolytes adapted...

Simple One-Step Method to Synthesize Polypyrrole-Indigo Carmine-Silver Nanocomposite

Directory of Open Access Journals (Sweden)

Lara Fernandes Loguercio

2016-01-01

Full Text Available A nanocomposite of indigo carmine doped polypyrrole/silver nanoparticles was obtained by a one-step electrochemical process. The nanocomposite was characterized by scanning electron microscopy, infrared spectroscopy, ultraviolet-visible-near infrared spectroscopy, and cyclic voltammetry. The simple one-step process allowed the growth of silver nanoparticles during the polymerization of polypyrrole, resulting in films with electrochromic behavior and improved electroactivity. In addition, polypyrrole chains in the nanocomposite were found to present longer conjugation length than pristine polypyrrole films.

Roll-to-Roll fabrication of large area functional organic materials

DEFF Research Database (Denmark)

Søndergaard, Roar R.; Hösel, Markus; Krebs, Frederik C

2013-01-01

With the prospect of extremely fast manufacture of very low cost devices, organic electronics prepared by thin film processing techniques that are compatible with roll-to-roll (R2R) methods are presently receiving an increasing interest. Several technologies using organic thin films...... research fields such as organic photovoltaics, organic thin film transistors, light-emitting diodes, polymer electrolyte membrane fuel cells, and electrochromic devices. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B: Polym Phys 000: 000–000, 2012...

GISAXS View of Induced Morphological Changes in Nanostructured CeVO4 Thin Films

Directory of Open Access Journals (Sweden)

Magdy Lučić Lavčević

2011-01-01

Full Text Available Nanostructured CeVO4 films, designed for applications in electrochemical cells and electrochromic devices, were obtained on glass substrates by the sol-gel process. An analysis of morphological modifications in these films, induced by ultrasonication, annealing, and introduction of lithium ions, was performed, using the grazing-incidence small-angle X-ray scattering technique (GISAXS. The GISAXS results are discussed and related with complementary examinations of the same films in real space, performed by scanning electron microscopy on a different length scale.

Practical design and production of optical thin films

CERN Document Server

Willey, Ronald R

2002-01-01

Providing insider viewpoints and perspectives unavailable in any other text, this book presents useful guidelines and tools to produce effective coatings and films. Covering subjects ranging from materials selection and process development to successful system construction and optimization, it contains expanded discussions on design visualization, dense wavelength division multiplexing, new coating equipment, electrochromic and chemically active coatings, ion-assisted deposition, and optical monitoring sensitivity. Furnishing real-world examples and know-how, the book introduces Fourier analysis and synthesis without difficult mathematical concepts and equations.

A magenta polypyrrole derivatised with Methyl Red azo dye: synthesis and spectroelectrochemical characterisation

International Nuclear Information System (INIS)

Almeida, Andresa K.A.; Dias, Jéssica M.M.; Santos, Diego P.; Nogueira, Fred A.R.; Navarro, Marcelo; Tonholo, Josealdo; Lima, Dimas J.P.; Ribeiro, Adriana S.

2017-01-01

Highlights: • A pyrrole (Py) derivative functionalised with methyl red (MRPy) was synthesised. • MRPy was polymerised electrochemically in LiClO_4/CH_3CN with BFEE. • Electrochromic properties of PMRPy and PPy doped with methyl red (PPy/MR) were compared. • Colour of the PMRPy changes from magenta to yellow depending on the pH. • PMRPy films might be applicable in optoelectronic devices or in pH sensors. - Abstract: A pyrrole derivative bearing 2-(4-dimethylaminophenylazo)benzoic acid, also known as Methyl Red (MR), was prepared by a simple synthetic route, and electropolymerised onto ITO/glass electrodes in (C_4H_9)_4NBF_4/CH_3CN in presence of boron trifluoride diethyl etherate (BFEE). Films of polypyrrole (PPy) and PPy doped with MR (PPy/MR) were also deposited onto ITO/glass in order to compare their electrochromic properties with the films of PPy derivatised with MR. Cyclic voltammogram of the poly[3-(N-pyrrolyl)propyl 2-(4-dimethylaminophenylazo)benzoate] (PMRPy) film displayed a redox pair with anodic peak potential (Epa) at ca. 0.53 V and cathodic peak potential (Epc) at 0.25 V vs. Ag/Ag"+, corresponding to the polymer p-doping, whilst the PPy/MR film shows capacitive behaviour with a redox pair in the cathodic region (Epa = −0.36 V and Epc = −0.62 V), similar to the PPy film (Epa = −0.10 V, and Epc = −0.15 V), and an anodic wave in the same potential range of that for PMRPy film. The electrochromic properties of the PMRPy film, such as chromatic contrast (Δ%T = 34.2%), switching time (τ = 10 s) and stability (Δ%T = 15% at the 100th cycle), were enhanced relative to the PPy/MR and PPy films. However, the colour of the PMRPy film changed from yellow (-0.8 V) to magenta (E = 1.0 V) in the first cycle and became light magenta at −0.8 V in the subsequent cycles. PMRPy films were also investigated in phosphate buffer solution (PBS, 2.0 ≤ pH ≤ 9.0) and after exposure to HCl vapour, in which the colour varied from magenta at pH = 2.0 to

Organic-inorganic hybrid polymer electrolytes based on polyether diamine, alkoxysilane, and trichlorotriazine: Synthesis, characterization, and electrochemical applications

Science.gov (United States)

Saikia, Diganta; Wu, Cheng-Gang; Fang, Jason; Tsai, Li-Duan; Kao, Hsien-Ming

2014-12-01

A new type of highly conductive organic-inorganic hybrid polymer electrolytes has been synthesized by the reaction of poly(propylene glycol)-block-poly(ethylene glycol)-block-poly(propylene glycol) bis(2-aminopropyl ether), 2,4,6-trichloro-1,3,5-triazine and alkoxysilane precursor 3-(glycidyloxypropyl)trimethoxysilane, followed by doping of LiClO4. The 13C and 29Si solid-sate NMR results confirm the successful synthesis of the organic-inorganic hybrid structure. The solid hybrid electrolyte thus obtained exhibits a maximum ionic conductivity of 1.6 × 10-4 S cm-1 at 30 °C, which is the highest among the organic-inorganic hybrid electrolytes. The hybrid electrolytes are electrochemically stable up to 4.2 V. The prototype electrochromic device with such a solid hybrid electrolyte demonstrates a good coloration efficiency value of 183 cm2 C-1 with a cycle life over 200 cycles. For the lithium-ion battery test, the salt free solid hybrid membrane is swelled with a LiPF6-containing electrolyte solution to reach an acceptable ionic conductivity value of 6.5 × 10-3 S cm-1 at 30 °C. The battery cell carries an initial discharge capacity of 100 mAh g-1 at 0.2C-rate and a coulombic efficiency of about 95% up to 30 cycles without the sign of cell failure. The present organic-inorganic hybrid electrolytes hold promise for applications in electrochromic devices and lithium ion batteries.

Fabry-Perot-like interference security image structures: From passive to active

Energy Technology Data Exchange (ETDEWEB)

Baloukas, B., E-mail: bill.baloukas@polymtl.ca; Trottier-Lapointe, W.; Martinu, L., E-mail: ludvik.martinu@polymtl.ca

2014-05-30

Counterfeiting of products and important documents is at an all-time high and is costing the world economy hundreds of billions of dollars yearly as well as posing significant safety and health hazards through the production of uncertified goods, e.g., pharmaceutical products. To limit these effects, interference-based optical security devices offering an angular color shift are still widely in use. Unfortunately, commercial iridescent materials are now readily available and represent a potential source of counterfeiting. In this short review, we first describe the basic principles behind passive interference security image structures (ISIS) and the qualities which have resulted in their integration into most important documents. Various features which have been added to ISIS in order to make them harder to duplicate yet simpler to authenticate are also presented (metamerism, magnetic materials, diffraction, etc.). We then address the implementation of active materials, mainly electrochromic WO{sub 3} as a means of generating two-level authentication devices. Finally, we discuss some general considerations to keep in mind when developing features for security applications. - Highlights: • We review Fabry–Perot-like metal-dielectric filters used in optical security. • We discuss/demonstrate recent additions: metamerism, magnetism and diffraction. • We demonstrate a feature based on the use of thin metallic mirrors. • We cover recent developments in the use of active materials. • We demonstrate an electrochromic feature with two levels of authentication.

Color in 'tungsten trioxide' thin films

International Nuclear Information System (INIS)

Gerard, P.; Deneuville, A.; Hollinger, G.; Duc, Tran Minh

1977-01-01

We show that evaporated tungsten trioxide amorphous layers commonly used in electrochromic displays actually have the composition WO_2_._7H_y (0.2< y<0.5). We emphasize that coloration of virgin transparent films can be obtained without injection of any external ion into the layer, and further that around a critical substoichiometry by sputtering, namely, WO_2_._5, one can prepare blue virgin layers without any hydrogen. The effect of substoichiometry on the valence of tungsten atoms has been followed by XPS measurements of sputtered layers.

Color in ''tungsten trioxide'' thin films

International Nuclear Information System (INIS)

Gerard, P.; Deneuville, A.; Hollinger, G.; Tran Minh Duc

1977-01-01

We show that evaporated tungsten trioxide amorphous layers commonly used in electrochromic displays actually have the composition WO/sub 2.7/H/sub y/ (0.2< y<0.5). We emphasize that coloration of virgin transparent films can be obtained without injection of any external ion into the layer, and further that around a critical substoichiometry by sputtering, namely, WO/sub 2.5/, one can prepare blue virgin layers without any hydrogen. The effect of substoichiometry on the valence of tungsten atoms has been followed by XPS measurements of sputtered layers

Establishing the value of advanced glazings

Energy Technology Data Exchange (ETDEWEB)

Lee, E; Selkowitz, S.

1999-01-01

Numerous glazing technologies are under development worldwide to improve the performance of building facades. High-performance glazings can provide substantial energy and related environmental benefits, but often at greatly increased first cost when compared to conventional design solutions. To increase market viability, we discuss strategies to reduce the actual and owner-perceived costs associated with developing and producing advanced window systems, specifically switchable electrochromic glazings, and we also suggest marketing strategies designed to appeal to early adopter and mainstream purchasers. These strategies may be applicable to a broad range of advanced glazing materials.

Solution-Processed Smart Window Platforms Based on Plasmonic Electrochromics

KAUST Repository

Abbas, Sara

2018-01-01

blocking. Despite this edge, this technology can benefit from important developments, including low-cost solution-based manufacturing on flexible substrates while maintaining durability and coloration efficiency, demonstration of independent control

Effect of electrolytes on electrochromic properties and morphology of ...

Indian Academy of Sciences (India)

Administrator

dimethoxy aniline) films. BUREERAT SUEPHATTHIMA1, NOPHAWAN PARADEE1, ANUVAT SIRIVAT1,* and. DATCHANEE PATTAVARAKORN2. 1The Petroleum and Petrochemical College, Chulalongkorn University, Bangkok 10330, Thailand.

Computationally Designed Oligomers for High Contrast Black Electrochromic Polymers

Science.gov (United States)

2017-05-05

area code) 706-867-3232 Standard Fonn 298 (Rev. 8198) Presa1bed by ANSI Std. Z39.18 Adobe Profeasional 7.0 Final Report For AFOSR Grant 15RT0592...visible as illustrated by the results of Figure 5 and Table 1. Here, we incorporated not only Ac aryl groups but also included dimethoxybenzene (B

Electroactive Polyurea Bearing Oligoaniline Pendants: Electrochromic and Anticorrosive Properties

Science.gov (United States)

2014-12-26

3] Cheng YJ, Yang SH, Hsu CS. Chem Rev 2009;109:5868e923. [4] Gu H, Guo J, Yan X, Wei H, Zhang X, Liu J, et al. Polymer 2014;55:4405e19. [5] Bigg DM...Reddy KN. Modern electrochemistry. New York: John Wiley and Sons; 1976. p. 622. [57] Bockris JOM, Reddy AK. Modern electrochemistry: an introduction to

A review of the growth of V2O5 films from 1885 to 2010

International Nuclear Information System (INIS)

Beke, Szabolcs

2011-01-01

This year is the 125th anniversary of the first synthesis of V 2 O 5 gels. The fascinating properties and wide application range of V 2 O 5 thin films have attracted significant attention over the past decades. Its wide optical band gap, layered structure, good chemical and thermal stability and excellent thermoelectric and electrochromic properties have made V 2 O 5 a promising material for industrial applications such as gas sensors, electrochromic devices, optical switching devices, and reversible cathode materials for Li batteries. Gels were the first form in which V 2 O 5 was synthesized at the end of the 19th century. Interest started to grow in the 1980s due to the discovery of their semiconducting properties and their use in antistatic coatings in the photographic industry. The rapid development of the sol-gel process brought new interest in V 2 O 5 gels. Following a short discussion of vanadium oxides and V 2 O 5 , I summarize all thin film preparation techniques known up to now and use reported optical band gaps to characterize different growth methods. An estimation of the Bohr radius for V 2 O 5 is also presented. This article provides an up-to-date review of more than a century (1885-2010) of research on the growth of vanadium oxide thin films. Nonetheless, due to the huge number of publications in the field, only those are selected and described which, according to the author, contribute the most to the field's further development.

Microstructural, photocatalysis and electrochemical investigations on CeTi2O6 thin films

International Nuclear Information System (INIS)

Verma, Amita; Goyal, Anshu; Sharma, R.K.

2008-01-01

The properties of sol-gel derived CeTi 2 O 6 thin films deposited using a solution of cerium chloride heptahydrate and titanium propoxide in ethanol are discussed. The effect of annealing temperature on structural, optical, photoluminescence, photocatalysis and electrochemical characteristics has been examined. Lowest annealing temperature for the formation of crystalline CeTi 2 O 6 phase in these samples is identified as 580 deg. C. The optical transmittance of the films is observed to be independent of the annealing temperature. The optical energy bandgap of the 600 deg. C annealed film for indirect transition is influenced by the presence of anatase phase of TiO 2 in its structure. Fourier transform infrared spectroscopy investigations have evidenced increased bond strength of the Ti-O-Ti network in the films as a function of annealing temperature. The photoluminescence intensity of the films has shown dependence on the annealing temperature with the films fired at 450 deg. C exhibiting the maximum photoluminescence activity. The decomposition of methyl orange and eosin (yellow) under UV-visible light irradiation in the presence of crystalline CeTi 2 O 6 films shows the presence of photoactivity in these films. The photocatalytic response of CeTi 2 O 6 films is found to be superior to the TiO 2 films. In comparison to crystalline films, the amorphous films have shown superior electrochemical characteristics. The 500 deg. C annealed amorphous films have exhibited the most appropriate properties for incorporation in electrochromic devices comprising tungsten oxide as the primary electrochromic electrode

Low Band Gap Donor–Acceptor Type Polymers Containing 2,3-Bis(4-(decyloxyphenylpyrido[4,3-b]pyrazine as Acceptor and Different Thiophene Derivatives as Donors

Directory of Open Access Journals (Sweden)

Yan Zhang

2016-10-01

Full Text Available Four donor–acceptor type conducting polymers, namely poly(2,3-bis(4-decyloxyphenyl-5,8-bis(4-thiophen-2-ylpyrido[4,3-b]pyrazine (P1, poly(2,3-bis(4-decyloxyphenyl-5,8-bis(4-butylthiophen-2-ylpyrido[4,3-b]pyrazine (P2, poly(2,3-bis(4-(decyloxyphenyl-5,8-bis(4-hexyloxythiophen-2-ylpyrido[4,3-b]pyrazine (P3 and poly(2,3-bis(4-(decyloxyphenyl-5,8-bis(2,3-dihydrothieno[3,4-b][1,4]dioxin-7-ylpyrido[4,3-b]pyrazine (P4, containing thiophene or its derivative as the donor and pyrido[4,3-b]pyrazine as the acceptor were prepared and characterized by cyclic voltammetry, scanning electron microscopy, and UV-Vis spectroscopy to detect the influence of the donor units’ strength on the electrochromic performances. The results demonstrated that all of the polymers could be reversibly reduced and oxidized by p-type doping and n-type doping, and showed near-infrared activities and different color changes in p-type doping process. Especially, P3 and P4 showed lower optical band gap than P1 and P2 due to the strong electron-donating hexyloxythiophen group of P3 and ethylenedioxythiophene group of P4. Besides, P3 and P4 displayed the saturated green color at the neutral state and the desirable transparency at the oxidized state. All the polymers displayed desirable optical contrasts, satisfactory coloration efficiency, excellent stability and short switching time, which made the polymers fascinating candidates in the electrochromic device applications.

Vacancy formation in MoO3: hybrid density functional theory and photoemission experiments

KAUST Repository

Salawu, Omotayo Akande

2016-09-29

Molybdenum oxide (MoO3) is an important material that is being considered for numerous technological applications, including catalysis and electrochromism. In the present study, we apply hybrid density functional theory to investigate O and Mo vacancies in the orthorhombic phase. We determine the vacancy formation energies of different defect sites as functions of the electron chemical potential, addressing different charge states. In addition, we investigate the consequences of defects for the material properties. Ultraviolet photoemission spectroscopy is employed to study the valence band of stoichiometric and O defective MoO3. We show that O vacancies result in occupied in-gap states.

Improved Electrochemical Cycling Durability in a Nickel Oxide Double-Layered Film.

Science.gov (United States)

Hou, Shuai; Zhang, Xiang; Tian, Yanlong; Zhao, Jiupeng; Geng, Hongbin; Qu, Huiying; Zhang, Hangchuan; Zhang, Kun; Wang, Binsheng; Gavrilyuk, Alexander; Li, Yao

2017-11-16

For the first time, a crystalline-amorphous double-layered NiO x film has been prepared by reactive radio frequency magnetron sputtering. This film has exhibited improved electrochemical cycling durability, whereas other electrochromic parameters have been maintained at the required level, namely, a short coloration/bleaching time (0.8 s/1.1 s) and an enhanced transmittance modulation range (62.2 %) at λ=550 nm. Additionally, the double-layered film has shown better reversibility than that of amorphous and crystalline single-layered films. © 2017 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Evaluation of 3D printed optofluidic smart glass prototypes.

Science.gov (United States)

Wolfe, Daniel; Goossen, K W

2018-01-22

Smart glass or smart windows are an innovative technology used for thermal management, energy efficiency, and privacy applications. Notable commercially available smart glass relies on an electric stimuli to modulate the glass from a transparent to a translucent mode of operation. However, the current market technologies, such as electrochromic, polymer dispersed liquid crystal, and suspended particle devices are expensive and suffer from solar absorption, poor transmittance modulation, and in some cases, continuous power consumption. The authors of this paper present a novel optofluidic smart glass prototype capable of modulating visible light transmittance from 8% to 85%.

In-situ fabrication of flexible vertically integrated electronic circuits by inkjet printing

International Nuclear Information System (INIS)

Wang Zhuo; Wu Wenwen; Yang Qunbao; Li Yongxiang; Noh, Chang-Ho

2009-01-01

In this paper, a facile approach for fabricating flexible vertically integrated electronic circuits is demonstrated. A desktop inkjet printer was modified and employed to print silver precursor on a polymer-coated buffer substrates. In-situ reaction was taken place and a conducting line was formed without need of a high temperature treatment. Through this process, several layers of metal integrated circuits were deposited sequentially with polymer buffer layers sandwiched between each layer. Hence, vertically integrated electronic components of diodes, solar cells, flexible flat panel displays, and electrochromic devices can be built with this simple and low-cost technique.

Vacancy formation in MoO3: hybrid density functional theory and photoemission experiments

KAUST Repository

Salawu, Omotayo Akande; Chroneos, Alexander; Vasilopoulou, Maria; Kennou, Stella; Schwingenschlö gl, Udo

2016-01-01

Molybdenum oxide (MoO3) is an important material that is being considered for numerous technological applications, including catalysis and electrochromism. In the present study, we apply hybrid density functional theory to investigate O and Mo vacancies in the orthorhombic phase. We determine the vacancy formation energies of different defect sites as functions of the electron chemical potential, addressing different charge states. In addition, we investigate the consequences of defects for the material properties. Ultraviolet photoemission spectroscopy is employed to study the valence band of stoichiometric and O defective MoO3. We show that O vacancies result in occupied in-gap states.

Dataset on electro-optically tunable smart-supercapacitors based on oxygen-excess nanograin tungsten oxide thin film

Directory of Open Access Journals (Sweden)

Akbar I. Inamdar

2017-10-01

Full Text Available The dataset presented here is related to the research article entitled “Highly Efficient Electro-optically Tunable Smart-supercapacitors Using an Oxygen-excess Nanograin Tungsten Oxide Thin Film” (Akbar et al., 2017 [9] where we have presented a nanograin WO3 film as a bifunctional electrode for smart supercapacitor devices. In this article we provide additional information concerning nanograin tungsten oxide thin films such as atomic force microscopy, Raman spectroscopy, and X-ray diffraction spectroscopy. Moreover, their electrochemical properties such as cyclic voltammetry, electrochemical supercapacitor properties, and electrochromic properties including coloration efficiency, optical modulation and electrochemical impedance spectroscopy are presented.

RF Magnetron Sputtering Deposited W/Ti Thin Film For Smart Window Applications

Science.gov (United States)

Oksuz, Lutfi; Kiristi, Melek; Bozduman, Ferhat; Uygun Oksuz, Aysegul

2014-10-01

Electrochromic (EC) devices can change reversible and persistent their optical properties in the visible region (400-800 nm) upon charge insertion/extraction according to the applied voltage. A complementary type EC is a device containing two electrochromic layers, one of which is anodically colored such as vanadium oxide (V2 O5) while the other cathodically colored such as tungsten oxide (WO3) which is separated by an ionic conduction layer (electrolyte). The use of a solid electrolyte such as Nafion eliminates the need for containment of the liquid electrolyte, which simplifies the cell design, as well as improves safety and durability. In this work, the EC device was fabricated on a ITO/glass slide. The WO3-TiO2 thin film was deposited by reactive RF magnetron sputtering using a 2-in W/Ti (9:1%wt) target with purity of 99.9% in a mixture gas of argon and oxygen. As a counter electrode layer, V2O5 film was deposited on an ITO/glass substrate using V2O3 target with the same conditions of reactive RF magnetron sputtering. Modified Nafion was used as an electrolyte to complete EC device. The transmittance spectra of the complementary EC device was measured by optical spectrophotometry when a voltage of +/-3 V was applied to the EC device by computer controlled system. The surface morphology of the films was characterized by scanning electron microscopy (SEM) and atomic force microscopy (AFM) (Fig. 2). The cyclic voltammetry (CV) for EC device was performed by sweeping the potential between +/-3 V at a scan rate of 50 mV/s.

Connectivity of the intracytoplasmic membrane of Rhodobacter sphaeroides: a functional approach.

Science.gov (United States)

Verméglio, André; Lavergne, Jérôme; Rappaport, Fabrice

2016-01-01

The photosynthetic apparatus in the bacterium Rhodobacter sphaeroides is mostly present in intracytoplasmic membrane invaginations. It has long been debated whether these invaginations remain in topological continuity with the cytoplasmic membrane, or form isolated chromatophore vesicles. This issue is revisited here by functional approaches. The ionophore gramicidin was used as a probe of the relative size of the electro-osmotic units in isolated chromatophores, spheroplasts, or intact cells. The decay of the membrane potential was monitored from the electrochromic shift of carotenoids. The half-time of the decay induced by a single channel in intact cells was about 6 ms, thus three orders of magnitude slower than in isolated chromatophores. In spheroplasts obtained by lysis of the cell wall, the single channel decay was still slower (~23 ms) and the sensitivity toward the gramicidin concentration was enhanced 1,000-fold with respect to isolated chromatophores. These results indicate that the area of the functional membrane in cells or spheroplasts is about three orders of magnitude larger than that of isolated chromatophores. Intracytoplasmic vesicles, if present, could contribute to at most 10% of the photosynthetic apparatus in intact cells of Rba. sphaeroides. Similar conclusions were obtained from the effect of a ∆pH-induced diffusion potential in intact cells. This caused a large electrochromic response of carotenoids, of similar amplitude as the light-induced change, indicating that most of the system is sensitive to a pH change of the external medium. A single internal membrane and periplasmic space may offer significant advantages concerning renewal of the photosynthetic apparatus and reallocation of the components shared with other bioenergetic pathways.

Spectral Properties and Orientation of Voltage-Sensitive Dyes in Lipid Membranes

KAUST Repository

Matson, Maria

2012-07-24

Voltage-sensitive dyes are frequently used for probing variations in the electric potential across cell membranes. The dyes respond by changing their spectral properties: measured as shifts of wavelength of absorption or emission maxima or as changes of absorption or fluorescence intensity. Although such probes have been studied and used for decades, the mechanism behind their voltage sensitivity is still obscure. We ask whether the voltage response is due to electrochromism as a result of direct field interaction on the chromophore or to solvatochromism, which is the focus of this study, as result of changed environment or molecular alignment in the membrane. The spectral properties of three styryl dyes, di-4-ANEPPS, di-8-ANEPPS, and RH421, were investigated in solvents of varying polarity and in model membranes using spectroscopy. Using quantum mechanical calculations, the spectral dependence of monomer and dimer ANEPPS on solvent properties was modeled. Also, the kinetics of binding to lipid membranes and the binding geometry of the probe molecules were found relevant to address. The spectral properties of all three probes were found to be highly sensitive to the local environment, and the probes are oriented nearly parallel with the membrane normal. Slow binding kinetics and scattering in absorption spectra indicate, especially for di-8-ANEPPS, involvement of aggregation. On the basis of the experimental spectra and time-dependent density functional theory calculations, we find that aggregate formation may contribute to the blue-shifts seen for the dyes in decanol and when bound to membrane models. In conclusion, solvatochromic and other intermolecular interactions effects also need to be included when considering electrochromic response voltage-sensitive dyes. © 2012 American Chemical Society.

Electric-field control of tri-state phase transformation with a selective dual-ion switch

Science.gov (United States)

Lu, Nianpeng; Zhang, Pengfei; Zhang, Qinghua; Qiao, Ruimin; He, Qing; Li, Hao-Bo; Wang, Yujia; Guo, Jingwen; Zhang, Ding; Duan, Zheng; Li, Zhuolu; Wang, Meng; Yang, Shuzhen; Yan, Mingzhe; Arenholz, Elke; Zhou, Shuyun; Yang, Wanli; Gu, Lin; Nan, Ce-Wen; Wu, Jian; Tokura, Yoshinori; Yu, Pu

2017-06-01

Materials can be transformed from one crystalline phase to another by using an electric field to control ion transfer, in a process that can be harnessed in applications such as batteries, smart windows and fuel cells. Increasing the number of transferrable ion species and of accessible crystalline phases could in principle greatly enrich material functionality. However, studies have so far focused mainly on the evolution and control of single ionic species (for example, oxygen, hydrogen or lithium ions). Here we describe the reversible and non-volatile electric-field control of dual-ion (oxygen and hydrogen) phase transformations, with associated electrochromic and magnetoelectric effects. We show that controlling the insertion and extraction of oxygen and hydrogen ions independently of each other can direct reversible phase transformations among three different material phases: the perovskite SrCoO3-δ (ref. 12), the brownmillerite SrCoO2.5 (ref. 13), and a hitherto-unexplored phase, HSrCoO2.5. By analysing the distinct optical absorption properties of these phases, we demonstrate selective manipulation of spectral transparency in the visible-light and infrared regions, revealing a dual-band electrochromic effect that could see application in smart windows. Moreover, the starkly different magnetic and electric properties of the three phases—HSrCoO2.5 is a weakly ferromagnetic insulator, SrCoO3-δ is a ferromagnetic metal, and SrCoO2.5 is an antiferromagnetic insulator—enable an unusual form of magnetoelectric coupling, allowing electric-field control of three different magnetic ground states. These findings open up opportunities for the electric-field control of multistate phase transformations with rich functionalities.

Electrochromic Properties of Tungsten Oxide Films Prepared by Reactive Sputtering

Science.gov (United States)

Kim, Min Hong; Kang, Tai Young; Jung, Yu Sup; Kim, Kyung Hwan

2013-05-01

WO3-x thin films were deposited on induim tin oxide (ITO) glass substrates with various oxygen flow ratios from 0.55 to 0.7 by the reactive facing-target sputtering method, at a power density of 4 W/cm2 and room temperature. The structural properties of the WO3-x thin films were measured by X-ray diffractometry and Raman spectral analysis. As-deposited WO3-x thin films had an amorphous structure. In the Raman spectra, WO3-x thin films exhibited two strong peaks at 770 and 950 cm-1 attributed to the vibrations of W6+-O and W6+=O bonds, respectively. The electrochemical and optical properties of WO3-x thin films were measured by cyclic voltammetry and UV/vis spectrometry. The results showed the highest charge density at an oxygen flow ratio of 0.7 and the highest transmittance in the visible range. The maximum coloration efficiency was 30.82 cm2/C at an oxygen flow ratio of 0.7.

Electrochromic Window Demonstration at the Donna Land Port of Entry

Energy Technology Data Exchange (ETDEWEB)

Fernandes, Luis L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lee, Eleanor S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Thanachareonkit, Anothai [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2015-05-01

The U.S. General Services Administration (GSA) Public Buildings Service (PBS) has jurisdiction, custody or control over 105 land ports of entry throughout the United States, 35 of which are located along the southern border. At these facilities, one of the critical functions of windows is to provide border control personnel with direct visual contact with the surrounding environment. This also can be done through surveillance cameras, but the high value that U.S. Customs and Border Protection (CPB) officers place on direct visual contact can be encapsulated in the following statement by a senior officer regarding this project: “nothing replaces line of sight.” In sunny conditions, however, outdoor visibility can be severely compromised by glare, especially when the orb of the sun is in the field of view. This often leads to the deployment of operable shading devices, such as Venetian blinds. While these devices address the glare, they obstruct the view of the surroundings, negating the visual security benefits of the windows.

Characteristics of tungsten oxide thin films prepared on the flexible substrates using pulsed laser deposition

International Nuclear Information System (INIS)

Suda, Yoshiaki; Kawasaki, Hiroharu; Ohshima, Tamiko; Yagyuu, Yoshihito

2008-01-01

Tungsten trioxide (WO 3 ) thin films have been prepared on the flexible indium tin oxide (ITO) substrates by pulsed laser deposition (PLD) using WO 3 targets in oxygen gas. Color of the WO 3 film on the flexible ITO substrates depends on the oxygen gas mixture. The plasma plume produced by PLD using a Nd:YAG laser and WO 3 target is investigated by temporal and spatial-resolved optical emission spectroscopy. WO 3 films prepared on the flexible ITO substrates show electrochromic properties, even when the substrates are bent. The film color changes from blue to transparent within 10-20 s after the applied DC voltage is turned off

Electrodeposition of lead on ITO electrode: influence of copper as an additive

International Nuclear Information System (INIS)

Avellaneda, Cesar O.; Napolitano, Marcos A.; Kaibara, Evandro K.; Bulhoes, Luis O.S.

2005-01-01

The reversible electrodeposition of metallic lead onto indium-tin oxide coated glass (ITO) was investigated and the influence of Cu(NO 3 ) 2 ·3H 2 O as additive was evaluated. The presence of Cu 2+ in the electrolytic solution produces a higher variation in the optical transmissivity. The optical response of the system changes from 85 to 10% relative to the ITO coated substrate. The kinetics of the electroreduction process of the Pb 2+ and Cu 2+ from the electrolytes has been determined by electrochemical impedance spectroscopy (EIS) at different electrodeposition potentials. This system may be a promising candidate for electrochromic materials

Al3+ doped V2O5 nanostructure: Synthesis and structural, morphological and optical characterization

International Nuclear Information System (INIS)

Venkatesan, A.; Chandar, N. Krishna; Jayavel, R.; Kumar, M. Krishna; Kumar, R. Mohan; Arjunan, S.

2013-01-01

Al x V 2-x O 5 (x = 0,2mol%) nanorods were synthesized at room temperature by facile surfactant free non-aqueous route. The phase pure orthorhombic structure and nanorods-like morphology have been studied by X-ray diffraction (XRD) and High resolution scanning electron microscopy. EDXS spectrum confirms the purity and presence of Al into V 2 O 5 lattice. Optical absorption from DRS UV-Vis spectra showed the band gap broadening due to quantum confinement effect. The results ensure that the dopant cation (Al 3+ ) successfully intercalated with the host cation (V 5+ ) and the products are promising for electrochromic and catalytic applications.

Electrochemistry and spectro-electrochemistry of dithizonatophenylmercury(II)

International Nuclear Information System (INIS)

Eschwege, Karel G. von; As, Lydia van; Swarts, Jannie C.

2011-01-01

Graphical abstract: Display Omitted Highlights: → CV and spectroelectrochemistry of dithizone and PhHgHDz, 3, is presented. → CV shows 3 has stable metal thioether (Hg-S-C), 1 oxidation and two reductions. → 3 is photochromic (t 1/2, relaxation = 1300 s). → Electrochemistry of ground and photo-activated 3 is identical. → Spectroelectrochemistry of 3 highlights electrochromism. - Abstract: The reactions between dithizone (H 2 Dz, (1)) or potassium dithizonate (K + HDz - , (2)) and phenylmercury(II) chloride gives PhHg(HDz), (3). Complex (3) is photochromic. In dichloromethane, the blue photo-exited state of (3) exhibits a first order relaxation process to regenerate the orange ground state with rate constant 0.00053 s -1 . The half life of this relaxation is ca. 1300 s. Electrochemically, on cyclic voltammetry time scale, the oxidations of (1) and (3) are different. A comparative voltammetric and spectro-electrochemical study of (1) and (3) in CH 2 Cl 2 containing 0.1 mol dm -3 [N( n Bu) 4 ][B(C 6 F 5 ) 4 ] revealed that the mercapto group of (1) can be oxidised in two one-electron transfer steps. A disulphide is first produced and then in a second oxidation step, HDz + is formed. In contrast, complex (3) shows only one ligand-based oxidation step. Upon complexation with phenylmercury the free mercaptan group of (1) becomes a stable 'metal thioether', Hg-S-C, which effectively prevents disulphide formation in (3) upon electrochemical oxidation. Both (1) and (3) shows two reduction steps. The electrochemical fingerprint of blue photo-excited (3) is identical to that of the orange ground state as no new functional groups are introduced upon irradiation; only bond rotation occurs. The different electronic spectra for each of the redox states of (3), obtained from spectro-electrochemical measurements, revealed that only the (3)/(3 - ) couple exhibits electrochromic properties.

The synthesis of new donor–acceptor polymers containing the 2,3-di(2-furyl) quinoxaline moiety: Fast-switching, low-band-gap, p- and n-dopable, neutral green-colored materials

International Nuclear Information System (INIS)

Xu, Zhen; Wang, Min; Fan, Weiyu; Zhao, Jinsheng; Wang, Huaisheng

2015-01-01

Highlights: • Three D-A type polymers based on 2,3-di(2-furyl) quinoxaline were synthesized and characterized. • The structure of substitution influences electrochromic properties of the polymers • All three polymers are both p- and n-type dopable and show excellent electrochromic properties. - Abstract: Three donor–acceptor type π-conjugated polymers were synthesized electrochemically:poly[2,3-di(2-furyl)-5,8-bis (2-(3,4-ethylenedioxythiophene)) quinoxaline] (PFETQ), poly[2,3-di(2-furyl)-5,8-bis(2-thienyl) quinoxaline] (PFTQ) and poly[2,3-di(2-furyl)-5,8-bis(2-(3-methoxythiophene)) quinoxaline] (PFMTQ). All of the synthesized polymers, contained the 2,3-di(2-furyl) quinoxaline moiety in the backbone as the acceptor unit and different thiophene derivatives as the donor units. The electroactivity of the monomers and the electrochemical properties of their polymers were investigated by cyclic voltammetry. The presence of the strong electron-donating ethylenedioxy and methoxy groups on the aromatic structure increased the electron density. Thus, the oxidation potential of FETQ and FMTQ shifted to a lower value than that of FTQ. The optical properties of the polymers were investigated by UV–vis–NIR spectroscopy. Both PFETQ and PFMTQ reveal two distinct absorption bands in the red and blue regions of the visible spectrum, while PFTQ has only one dominant wavelength at 596 nm in the visible region. The colorimetry analysis revealed that while PFTQ has a light blue color, PFETQ and PFMTQ are green in the neutral state. The optical band gaps, defined as the onset of the π–π* transition, were found to be 1.15 eV for PFETQ, 1.2 eV for PFMTQ and 1.34 eV for PFTQ. Moreover, all three polymers showed both n-doping and fast switching times

Bio-inspired materials for electrochemical devices

Science.gov (United States)

Pawlicka, A.; Firmino, A.; Sentanin, F.; Sabadini, R. C.; Jimenez, D. E. Q.; Jayme, C. C.; Mindroiu, M.; Zgarian, R. G.; Tihan, G. T.; Rau, I.; Silva, M. M.; Nogueira, A. F.; Kanicki, J.; Kajzar, F.

2015-10-01

Natural macromolecules are very promising row materials to be used in modern technology including security and defense. They are abundant in nature, easy to extract and possess biocompatibility and biodegradability properties. These materials can be modified throughout chemical or physical processes, and can be doped with lithium and rare earth salts, ionic liquids, organic and inorganic acids. In this communication samples of DNA and modified DNA were doped with Prussian Blue (PB), poly(ethylene dioxythiophene) (PEDOT), europium and erbium triflate and organic dyes such as Nile Blue (NB), Disperse Red 1 (DR1) and Disperse Orange 3 (DO3). The colored or colorless membranes were characterized by electrochemical and spectroscopic measurements, and they were applied in electrochromic devices (ECDs) and dye sensitized solar cells (DSSC). ECDs change the color under applied potential, so they can modulate the intensity of transmitted light of 15 to 35%. As the electrochromic materials, WO3 or Prussian blue (PB), are usually blue colored, the color change is from transparent to blue. DNA, and the complexes: DNA-CTMA, DNA-DODA and DNAPEDOT: PSS were also investigated as either hole carrier material (HTM) or polymer electrolyte in dye-sensitized solar cells (DSSC). The DNA-based samples as HTM in small DSSCs revealed a solar energy conversion efficiency of 0.56%. Polymer electrolytes of DNA-CTMA and DNA-DODA, both with 10 wt% of LiI/I2, applied in small DSSC, exhibited the efficiencies of 0.18 and 0.66%, respectively. The obtained results show that natural macromolecules-based membranes are not only environmentally friendly but are also promising materials to be investigated for several electrochemical devices. However, to obtain better performances more research is still needed.

A Dual-Stimuli-Responsive Sodium-Bromine Battery with Ultrahigh Energy Density.

Science.gov (United States)

Wang, Faxing; Yang, Hongliu; Zhang, Jian; Zhang, Panpan; Wang, Gang; Zhuang, Xiaodong; Cuniberti, Gianaurelio; Feng, Xinliang

2018-06-01

Stimuli-responsive energy storage devices have emerged for the fast-growing popularity of intelligent electronics. However, all previously reported stimuli-responsive energy storage devices have rather low energy densities (energy density, electrochromic effect, and fast thermal response is demonstrated. Remarkably, the fabricated Na//Br 2 battery exhibits a large operating voltage of 3.3 V and an energy density up to 760 Wh kg -1 , which outperforms those for the state-of-the-art stimuli-responsive electrochemical energy storage devices. This work offers a promising approach for designing multi-stimuli-responsive and high-energy rechargeable batteries without sacrificing the electrochemical performance. © 2018 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

All printed touchless human-machine interface based on only five functional materials

Science.gov (United States)

Scheipl, G.; Zirkl, M.; Sawatdee, A.; Helbig, U.; Krause, M.; Kraker, E.; Andersson Ersman, P.; Nilsson, D.; Platt, D.; Bodö, P.; Bauer, S.; Domann, G.; Mogessie, A.; Hartmann, Paul; Stadlober, B.

2012-02-01

We demonstrate the printing of a complex smart integrated system using only five functional inks: the fluoropolymer P(VDF:TrFE) (Poly(vinylidene fluoride trifluoroethylene) sensor ink, the conductive polymer PEDOT:PSS (poly(3,4 ethylenedioxythiophene):poly(styrene sulfonic acid) ink, a conductive carbon paste, a polymeric electrolyte and SU8 for separation. The result is a touchless human-machine interface, including piezo- and pyroelectric sensor pixels (sensitive to pressure changes and impinging infrared light), transistors for impedance matching and signal conditioning, and an electrochromic display. Applications may not only emerge in human-machine interfaces, but also in transient temperature or pressure sensing used in safety technology, in artificial skins and in disposable sensor labels.

2D and 3D photonic crystal materials for photocatalysis and electrochemical energy storage and conversion

Science.gov (United States)

Collins, Gillian; Armstrong, Eileen; McNulty, David; O’Hanlon, Sally; Geaney, Hugh; O’Dwyer, Colm

2016-01-01

Abstract This perspective reviews recent advances in inverse opal structures, how they have been developed, studied and applied as catalysts, catalyst support materials, as electrode materials for batteries, water splitting applications, solar-to-fuel conversion and electrochromics, and finally as photonic photocatalysts and photoelectrocatalysts. Throughout, we detail some of the salient optical characteristics that underpin recent results and form the basis for light-matter interactions that span electrochemical energy conversion systems as well as photocatalytic systems. Strategies for using 2D as well as 3D structures, ordered macroporous materials such as inverse opals are summarized and recent work on plasmonic–photonic coupling in metal nanoparticle-infiltrated wide band gap inverse opals for enhanced photoelectrochemistry are provided. PMID:27877904

Al{sup 3+} doped V{sub 2}O{sub 5} nanostructure: Synthesis and structural, morphological and optical characterization

Energy Technology Data Exchange (ETDEWEB)

Venkatesan, A. [Department of Physics, Panimalar Engineering College, Chennai - 600 123, India and Department of Physics, Presidency College, Chennai - 600 005 (India); Chandar, N. Krishna; Jayavel, R. [Centre for Nanoscience and Technology, Anna University, Chennai - 600 025 (India); Kumar, M. Krishna; Kumar, R. Mohan [Department of Physics, Presidency College, Chennai - 600 005 (India); Arjunan, S. [Department of Physics, R.M.K. Engineering College, Chennai - 601 206 (India)

2013-02-05

Al{sub x}V{sub 2-x}O{sub 5}(x = 0,2mol%) nanorods were synthesized at room temperature by facile surfactant free non-aqueous route. The phase pure orthorhombic structure and nanorods-like morphology have been studied by X-ray diffraction (XRD) and High resolution scanning electron microscopy. EDXS spectrum confirms the purity and presence of Al into V{sub 2}O{sub 5} lattice. Optical absorption from DRS UV-Vis spectra showed the band gap broadening due to quantum confinement effect. The results ensure that the dopant cation (Al{sup 3+}) successfully intercalated with the host cation (V{sup 5+}) and the products are promising for electrochromic and catalytic applications.

Syntheses of electroactive layers based on functionalized anthracene for electrochromic applications

International Nuclear Information System (INIS)

Yildirim, A.; Tarkuc, S.; Ak, M.; Toppare, L.

2008-01-01

A new monomer (DTAT) was synthesized via linking 3,4-ethylenedioxythiophene (EDOT) on anthracene. The polymer, P(DTAT) was electrosynthesized by anodic oxidation of the corresponding monomer in 0.1 M LiClO 4 acetonitrile (ACN) solution. The optical properties, the absorption spectra and the kinetics, were examined. Spectroelectrochemical analysis showed that P(DTAT) has an electronic band gap (due to π-π* transition) of 1.57 eV at 776 nm. Copolymers of DTAT with EDOT were prepared in ACN/LiClO 4 (0.1 M) solvent-electrolyte couple by varying applied potential. The incorporation of an EDOT into the full conjugated backbone, DTAT, affects its optical behavior resulting in different colors; a claret red neutral state, gray and red intermediate states and a blue oxidized state

Electrochromic properties of polyaniline-coated fiber webs for tissue engineering applications.

Science.gov (United States)

Beregoi, Mihaela; Busuioc, Cristina; Evanghelidis, Alexandru; Matei, Elena; Iordache, Florin; Radu, Mihaela; Dinischiotu, Anca; Enculescu, Ionut

2016-08-30

By combining the electrospinning method advantages (high surface-to-volume ratio, controlled morphology, varied composition and flexibility for the resulting structures) with the electrical activity of polyaniline, a new core-shell-type material with potential applications in the field of artificial muscles was synthesized. Thus, a poly(methylmethacrylate) solution was electrospun in optimized conditions to obtain randomly oriented polymer fiber webs. Further, a gold layer was sputtered on their surface in order to make them conductive and improve the mechanical properties. The metalized fiber webs were then covered with a PANI layer by in situ electrochemical polymerization starting from aniline and using sulphuric acid as oxidizing agent. By applying a small voltage on PANI-coated fiber webs in the presence of an electrolyte, the oxidation state of PANI changes, which is followed by the device color modification. The morphological, electrical and biological properties of the resulting multilayered material were also investigated. Copyright © 2015 Elsevier B.V. All rights reserved.

Electrogenerated networks from poly[4-(diphenylaminobenzyl methacrylate] and their electrochromic properties

Directory of Open Access Journals (Sweden)

O. I. Negru

2014-09-01

Full Text Available Poly[4-(diphenylaminobenzyl methacrylate] with well-defined molecular weight and low polydispersity was prepared by atom transfer radical polymerization (ATRP using 4-(diphenylamino benzyl 2-bromo-2-methyl-propanoate as initiator and CuBr/2,2'-bipyridine as catalytic complex. Electrochemical behavior and optical properties of the polymers were investigated by cyclic voltammetry and UV-Vis and fluorescence spectroscopy. Cyclic votammetric studies revealed that the redox processes were accompanied by dimerization of triphenylamine pendant groups. The initial polymer was postmodified, in solution or bulk, by electrochemical oxidation leading to a crosslinked and insoluble network with electro -chromic properties, accompanied by strong color changes with high coloration efficiency. The crosslinking reaction took place between triphenylamine groups through para free positions leading to tetraphenylbenzidine bridges. The structure of polymers was confirmed by Fourier transform infrared (FT-IR spectroscopy and 1H and 13C-nuclear magnetic resonance spectroscopy. Morphology studies of the cross-linked film have evidenced a smooth and continuous aspect without any pinholes or defects.

Sol-gel coatings on large area glass sheets for electrochromic devices

NARCIS (Netherlands)

Vroon, Z.A.E.P.; Spee, C.I.M.A.

1997-01-01

The preparation of vanadium and tungsten oxide coatings is described using vanadium oxide tri-2-propoxide/2-propanol and tungsten penta-ethoxide/2-propanol solutions. These solutions are dip coated onto K-glass substrates and cured. For vanadium oxide coatings it is shown that sol-gel/dip coat

High Turndown Ratio, High Delta-Emittance, Variable Emissivity Electrochromics, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Variable-emittance materials are in high demand for applications ranging from manned and unmanned space platforms (e.g. in radiators at the Moon's poles where damage...

A photometric high-throughput method for identification of electrochemically active bacteria using a WO3 nanocluster probe.

Science.gov (United States)

Yuan, Shi-Jie; He, Hui; Sheng, Guo-Ping; Chen, Jie-Jie; Tong, Zhong-Hua; Cheng, Yuan-Yuan; Li, Wen-Wei; Lin, Zhi-Qi; Zhang, Feng; Yu, Han-Qing

2013-01-01

Electrochemically active bacteria (EAB) are ubiquitous in environment and have important application in the fields of biogeochemistry, environment, microbiology and bioenergy. However, rapid and sensitive methods for EAB identification and evaluation of their extracellular electron transfer ability are still lacking. Herein we report a novel photometric method for visual detection of EAB by using an electrochromic material, WO(3) nanoclusters, as the probe. This method allowed a rapid identification of EAB within 5 min and a quantitative evaluation of their extracellular electron transfer abilities. In addition, it was also successfully applied for isolation of EAB from environmental samples. Attributed to its rapidness, high reliability, easy operation and low cost, this method has high potential for practical implementation of EAB detection and investigations.

Flake like V_2O_5 nanoparticles for ethanol sensing at room temperature

International Nuclear Information System (INIS)

Chitra, M.; Uthayarani, K.; Rajasekaran, N.; Neelakandeswari, N.; Girija, E. K.; Padiyan, D. Pathinettam

2016-01-01

The versatile redox property of vanadium oxide explores it in various applications like catalysis, electrochromism, electrochemistry, energy storage, sensors, microelectronics, batteries etc., In this present work, vanadium oxide was prepared via hydrothermal route followed by calcination. The structural and lattice parameters were analysed from the powder X-ray diffraction (XRD) pattern. The morphology and the composition of the sample were obtained from Field emission Scanning electron microscopic (FeSEM) and Energy Dispersive X-ray (EDAX) Spectrometric analysis respectively. The sensitivity, response – recovery time of the sample towards ethanol (0 ppm – 300 ppm) sensing at room temperature was measured and the present investigation on vanadium oxide nanoparticles over the flakes shows better sensitivity (30%) at room temperature.

Development and applications of transparent conductive nanocellulose paper

Science.gov (United States)

Li, Shaohui; Lee, Pooi See

2017-12-01

Increasing attention has been paid to the next generation of 'green' electronic devices based on renewable nanocellulose, owing to its low roughness, good thermal stability and excellent optical properties. Various proof-of-concept transparent nanopaper-based electronic devices have been fabricated; these devices exhibit excellent flexibility, bendability and even foldability. In this review, we summarize the recent progress of transparent nanopaper that uses different types of nanocellulose, including pure nanocellulose paper and composite nanocellulose paper. The latest development of transparent and flexible nanopaper electronic devices are illustrated, such as electrochromic devices, touch sensors, solar cells and transistors. Finally, we discuss the advantages of transparent nanopaper compared to conventional flexible plastic substrate and the existing challenges to be tackled in order to realize this promising potential.

Development and applications of transparent conductive nanocellulose paper.

Science.gov (United States)

Li, Shaohui; Lee, Pooi See

2017-01-01

Increasing attention has been paid to the next generation of 'green' electronic devices based on renewable nanocellulose, owing to its low roughness, good thermal stability and excellent optical properties. Various proof-of-concept transparent nanopaper-based electronic devices have been fabricated; these devices exhibit excellent flexibility, bendability and even foldability. In this review, we summarize the recent progress of transparent nanopaper that uses different types of nanocellulose, including pure nanocellulose paper and composite nanocellulose paper. The latest development of transparent and flexible nanopaper electronic devices are illustrated, such as electrochromic devices, touch sensors, solar cells and transistors. Finally, we discuss the advantages of transparent nanopaper compared to conventional flexible plastic substrate and the existing challenges to be tackled in order to realize this promising potential.

Influence of disordered morphology on electrochromic stability of WO{sub 3}/PPy

Energy Technology Data Exchange (ETDEWEB)

Gaikwad, Digambar K. [D. Y. Patil College of Engineering & Technology, Kasaba Bawada, Kolhapur, 416006, Maharashtra (India); Mali, Sawanta S.; Hong, Chang K. [Polymer Energy Materials Laboratory, Department of Advanced Chemical Engineering, Chonnam National University, Gwangju, 500-757 (Korea, Republic of); Kadam, Anamika V., E-mail: anamikasonavane@rediff.com [D. Y. Patil College of Engineering & Technology, Kasaba Bawada, Kolhapur, 416006, Maharashtra (India); D.Y. Patil Medical University, Kasaba Bawada, Kolhapur, 416006, Maharashtra (India)

2016-06-05

Tungsten oxide (WO{sub 3}) films are critical for smart windows because of their capacity of varying the throughput of visible light and solar energy. This study highlights the evolution of structural and morphological changes of electrodeposited WO{sub 3} thin films coated with polypyrrole (PPy) by using chemical bath deposition. The structural and surface properties of WO{sub 3} thin films were studied using X-ray diffraction, Fourier transform infrared spectroscopy, scanning electron microscopy, and transmission electron microscopy. The electrochemical stability was inspected using repetitive cyclic voltammetry (CV) cycles for each sample in LiClO{sub 4}-PC electrolyte for prolonged periods. The results showed an improvement in the electrochemical stability after the CV study. - Graphical abstract: Mechanism: A schematic of the mechanism is proposed in above fig. The mechanism is based on three step process: (i) WO{sub 3} coated on ITO by electrodeposition followed by thermal treatment. It produces ordered nanoarrayed morphology. (ii) A second step involving deposition of PPy by chemical bath deposition on ITO. It possesses globular morphology. (iii) When PPy coated on WO{sub 3}, PPy applies shearing force on WO{sub 3} and produces disordered nanoarrayed morphology. - Highlights: • Nanoarrayed WO{sub 3}/PPy composite was synthesized. • Interplanar spacing enhances due to PPy coating. • PPy applies shearing force on WO{sub 3} produces disordered morphology. • Nanocomposite showed high stability in LiClO{sub 4}-PC.

Chromogenic switchable glazing: Towards the development of the smart window

Energy Technology Data Exchange (ETDEWEB)

Lampert, C.M.

1995-06-01

The science and technology of chromogenic materials for switchable glazings in building applications is discussed. These glazings can be used for dynamic control of solar and visible energy. Currently many researchers and engineers are involved with the development of products in this field. A summary of activities in Japan, Europe, Australia, USA and Canada is made. The activities of the International Energy Agency are included. Both non-electrically activated and electrically activated glazings are discussed. Technologies covered in the first category are photochromics, and thermochromics and thermotropics. A discussion of electrically activated chromogenic glazings includes dispersed liquid crystals, dispersed particles and electrochromics. A selection of device structures and performance characteristics are compared. A discussion of transparent conductors is presented. Technical issues concerning large-area development of smart windows are discussed.

Molecular Design of Semiconducting Polymers for High-Performance Organic Electrochemical Transistors

KAUST Repository

Nielsen, Christian B.

2016-07-22

The organic electrochemical transistor (OECT), capable of transducing small ionic fluxes into electronic signals in an aqueous envi-ronment, is an ideal device to utilize in bioelectronic applications. Currently, most OECTs are fabricated with commercially availa-ble conducting poly(3,4-ethylenedioxythiophene) (PEDOT)-based suspensions and are therefore operated in depletion mode. Here, we present a series of semiconducting polymers designed to elucidate important structure-property guidelines required for accumulation mode OECT operation. We discuss key aspects relating to OECT performance such as ion and hole transport, elec-trochromic properties, operational voltage and stability. The demonstration of our molecular design strategy is the fabrication of accumulation mode OECTs that clearly outperform state-of-the-art PEDOT based devices, and show stability under aqueous oper-ation without the need for formulation additives and cross-linkers.

Development and applications of transparent conductive nanocellulose paper

Science.gov (United States)

Li, Shaohui; Lee, Pooi See

2017-01-01

Abstract Increasing attention has been paid to the next generation of ‘green’ electronic devices based on renewable nanocellulose, owing to its low roughness, good thermal stability and excellent optical properties. Various proof-of-concept transparent nanopaper-based electronic devices have been fabricated; these devices exhibit excellent flexibility, bendability and even foldability. In this review, we summarize the recent progress of transparent nanopaper that uses different types of nanocellulose, including pure nanocellulose paper and composite nanocellulose paper. The latest development of transparent and flexible nanopaper electronic devices are illustrated, such as electrochromic devices, touch sensors, solar cells and transistors. Finally, we discuss the advantages of transparent nanopaper compared to conventional flexible plastic substrate and the existing challenges to be tackled in order to realize this promising potential. PMID:28970870

The management and conversion of light

DEFF Research Database (Denmark)

Jensen, Jacob

methods. A key challenge in device fabrication is the development of a suitable electrolyte system, and two electrolyte systems are compared in fully printable and laminated devices on flexible substrates. Devices of various sizes are presented and the transmission contrast, when switched between...... the fully bleached and fully colored state, are found to be 43 % at Absmax with a response time of less than 10 seconds. To show possible applications, an electrochromic display powered by a printed organic photovoltaic device are demonstrated, that can switch between the two redox states during solar......; carbon dioxide reduction and water splitting. Practical solutions are presented, and the use of flexible substrates as carrier foils is explored. A key challenge in these conversion systems is the necessary precautions that must be taken when evaluating conversion and this is most convincingly done...

Reversible polycolour change of viologens from violet through transparent to white

International Nuclear Information System (INIS)

Hoshino, Katsuyoshi; Oikawa, Yosuke; Sakabe, Ichiro; Komatsu, Toshiki

2009-01-01

The electrochromic properties of 1,1'-dibenzyl-4,4'-bipyridinium and 1,1'-diheptyl-4,4'-bipyridinium were investigated in the presence of MBr (M = Li + , Na + , and K + ). The cyclic voltammograms of these viologens showed a white-coloured state in addition to the usual violet one-electron reduction state and the colourless divalent state. Chemical analyses (FT-IR and XPS spectra) of the white film and some control experiments with different supporting electrolytes, MX (X = Cl - and I - ), revealed that the viologens formed water-insoluble ion pairs with tribromide generated by the electrooxidation of monobromide to produce a white film. The film was reversibly decolourized electrochemically to the initial transparent state, providing the polyelectrochromism using the simple viologen/MBr systems. The colouration efficiencies for the violet and the white-coloured states were 170 cm 2 /C and 104 cm 2 /C, respectively.

Sealed two-electrode photoelectrochemical cell based on nanocrystalline TiO2 analyzed as a UV sensor

International Nuclear Information System (INIS)

Forcade, Fresnel; Gonzalez, Bernardo; Maqueda, Ma. de la Luz; Curbelo, Larisa; Vigil, Elena; Jennings, James R.; Dunn, Halina; Wang, Hongxia; PeteR, Lauri M.

2008-01-01

Potentialities as UV sensor of a sealed two-electrode photoelectrochemical cell (PEC) based on nanocrystalline TiO 2 are analyzed. Ultraviolet component of solar light is responsible for a number of skin disorders and diseases. An inexpensive and simple UV sensor would be convenient to measure the UV intensity been exposed to. Nanocrystalline TiO 2 is a rather inexpensive material, innocuous and very stable which is intensively studied at the present moment because of its possible applications in dye-sensitized solar cells, photocatalysis, electrochromics, etc. The method for obtaining the sensor and its structure are described. Different TiO 2 layer structures for the photoelectrode are studied. Important parameters, such as, spectral response, external quantum efficiency, current vs light intensity and current-voltage curve are presented. Results show prospective for the implementation of this type of sensor. (Full text)

Thermal and electrothermal sensitivity of polyglutamic acid with incorporated carbocyanine dyes in Langmuir-Blodgett films

Energy Technology Data Exchange (ETDEWEB)

Popova, G. [Mendeleyev University of Chemical Technology of Russia, Miusskaya sq., 9, Moscow 125047 (Russian Federation)], E-mail: galina@muctr.edu.ru; Spitsyn, A; Vantsyan, M [Mendeleyev University of Chemical Technology of Russia, Miusskaya sq., 9, Moscow 125047 (Russian Federation); Matveeva, N [Lukin Institute Phys. Problems, Zelenograd (Russian Federation); Yudin, S; Palto, S [Crystallography Institute Rus., Leninsky prosp., 57, 117336 Moscow (Russian Federation)

2008-03-31

Light-and electrosensitive carbocyanine dyes were incorporated into polyglutamic acid via covalent and non-covalent bonding. The reversible colour change on heating the Langmuir-Blodgett films of polyaminoacid has been studied by absorption spectroscopy and electroconductivity techniques. Characteristic shifts of the absorption spectrum are explained by formation of aggregates and hydrogen bonds. It was shown that H-aggregates and dimers are formed in Langmuir-Blodgett films; each type of assemblies contributes to the absorption spectrum. At elevated temperatures the ratio between concentrations of monomers, dimers and H-aggregates varies due to a breakdown of a part of aggregates into monomers. The change in molecular polarizability was also noticed. Electroconductivity of Langmuir-Blodgett films is observed in longitudinal and transverse directions. Electrochromic effect is noticed under weak electric current by change from red to colourless with iodine doping.

Spray deposited CeO2–TiO2 counter electrode for electrochromic ...

Indian Academy of Sciences (India)

Abstract. Optically passive thin films of CeO2–TiO2 mixed oxides with molar ratio of Ce/Ti of 0.05 were deposited by the spray pyrolysis technique (SPT) on a glass and fluorine-doped tin oxide (FTO)-coated glass substrates. Precur- sor solution containing cerium nitrate hexahydrate (Ce(NO3)2·6H2O) and titanium ...

Layer-by-Layer Assembly of a pH-Responsive and Electrochromic Thin Film

Science.gov (United States)

Schmidt, Daniel J.; Pridgen, Eric M.; Hammond, Paula T.; Love, J. Christopher

2010-01-01

This article summarizes an experiment on thin-film fabrication with layer-by-layer assembly that is appropriate for undergraduate laboratory courses. The purpose of this experiment is to teach students about self-assembly in the context of thin films and to expose students to the concepts of functional polymeric coatings. Students dip coat…

Controlling the volatility of the written optical state in electrochromic DNA liquid crystals

Science.gov (United States)

Liu, Kai; Varghese, Justin; Gerasimov, Jennifer Y.; Polyakov, Alexey O.; Shuai, Min; Su, Juanjuan; Chen, Dong; Zajaczkowski, Wojciech; Marcozzi, Alessio; Pisula, Wojciech; Noheda, Beatriz; Palstra, Thomas T. M.; Clark, Noel A.; Herrmann, Andreas

2016-05-01

Liquid crystals are widely used in displays for portable electronic information display. To broaden their scope for other applications like smart windows and tags, new material properties such as polarizer-free operation and tunable memory of a written state become important. Here, we describe an anhydrous nanoDNA-surfactant thermotropic liquid crystal system, which exhibits distinctive electrically controlled optical absorption, and temperature-dependent memory. In the liquid crystal isotropic phase, electric field-induced colouration and bleaching have a switching time of seconds. Upon transition to the smectic liquid crystal phase, optical memory of the written state is observed for many hours without applied voltage. The reorientation of the DNA-surfactant lamellar layers plays an important role in preventing colour decay. Thereby, the volatility of optoelectronic state can be controlled simply by changing the phase of the material. This research may pave the way for developing a new generation of DNA-based, phase-modulated, photoelectronic devices.

Towards Near-Infrared Photosensitization of Tungsten Trioxide Nanostructured Films by Upconverting Nanoparticles

Science.gov (United States)

Venne, Frederic

Nanostructured metal oxides semiconductors are widely used in solar energy related applications, such as in dye-sensitized solar cells. Tungsten trioxide (WO3) is an electrochromic material, extensively investigated in solar energy conversion (e.g. photoelectrochemistry) and conservation (e.g. electrochromism). However, WO3, because of its wide bandgap (≈ 2.5 eV), is transparent to an important portion of the solar spectrum and can effectively absorb light only up to ca. 500 nm, which limits the power conversion efficiency of devices based thereon. Upconverting materials can absorb several low-energy photons to emit one high-energy photon. In particular, upconverting nanoparticles are widely studied in biomedical and solar energy applications, as they can transform two or several infrared photons in a visible photon. As the Sun contains important NIR and IR portion, UCNPs are interesting candidates to transform NIR or IR light into visible light to be absorbed by wide bandgap semiconductor, such as metal oxides. The work presented in this master's thesis consists in embedding NaGdF4:Er3+, Yb3+ UCNPs into a nanostructured WO3 matrix. The objective is to increase the power conversion efficiency of WO3 after solar light harvesting. The integration of two materials with nanostructured nature has the potential to lead to a good synergy between them. We include an article in this master's thesis. In this article, we report on the mixing of NaGdF4:Er3+, Yb 3+ UCNPs with WO3 in solution and on the deposition of the two-component solution on ITO-patterned electrodes. After engineering the fabrication and deposition of the thin nanocomposite films, they were systematically studied. Morphology was studied by atomic force microscopy, structure by X-ray diffraction, photoluminescence by fluorescence hyperspectral microscopy, and charge carrier transport under NIR irradiation by current-time measurements. Notably, we observed an increase in the value of the current with

Electrochemical properties of amorphous WO3 coatings grown on polycarbonate by aerosol-assisted CVD

International Nuclear Information System (INIS)

Vernardou, D.; Drosos, H.; Spanakis, E.; Koudoumas, E.; Katsarakis, N.; Pemble, M.E.

2012-01-01

Highlights: ► Tungsten oxide is aerosol assisted chemically vapor deposited on polycarbonate. ► Their properties are dependent on the Ar:O 2 ratio during deposition. ► The porous structure enhances their electrochemical performance. - Abstract: Tungsten oxide coatings are chemically vapor deposited on polycarbonate via aerosol assisted at 125 °C. The effect of the Ar:O 2 ratio on the structural, morphological and electrochemical properties of the samples is investigated. The coating grown using Ar:O 2 ratio of 50:50, exhibits the best electrochemical activity and the fastest colouration-bleaching response. At the same time it offers a high specific capacitance that does not degrade upon at least 1000 successive charging–discharging cycles as studied by voltammetry in a solution of 1 M LiClO 4 . The importance of morphology towards the enhancement of the electrochromic behaviour of the coatings is discussed.

Electrochemical properties of opal-V6O13 composites

International Nuclear Information System (INIS)

Vernardou, D.; Apostolopoulou, M.; Louloudakis, D.; Spanakis, E.; Katsarakis, N.; Koudoumas, E.; McGrath, J.; Pemble, M.E.

2014-01-01

Highlights: • Opal-V 6 O 13 composites grown at 95 °C for 50 h. • The deposition period affects the void filling of the opals. • The electrochemical performance is correlated with the oxide’s characteristics. -- Abstract: Vanadium oxides were hydrothermally grown on opal glass substrates at 95 °C. The deposition period was observed to affect the structure of the oxides and the voids filling of the opal surfaces. V 6 O 13 grown on opal for 50 h presented satisfactory electrochemical performance and electrochromic response with a contrast ratio of 2. The specific capacitance of this composite reached a value of 192 F g −1 , which was stable up to 500 continuous charge intercalation/deintercalation scans. The importance of achieving crystalline V 6 O 13 and high opal surface coverage towards the enhancement of the electrochemical properties is presented

A first-principles study of the electronic structure of the sulvanite compounds

Energy Technology Data Exchange (ETDEWEB)

Osorio-Guillen, J.M., E-mail: jorge.osorio@fisica.udea.edu.co [Instituto de Fisica, Universidad de Antioquia, Medellin A.A. 1226 (Colombia); Espinosa-Garcia, W.F. [Instituto de Fisica, Universidad de Antioquia, Medellin A.A. 1226 (Colombia)

2012-03-15

We have investigated by means of first-principles total energy calculations the electronic structure of the sulvanite compounds: Cu{sub 3}VS{sub 4}, Cu{sub 3}NbS{sub 4} and Cu{sub 3}TaS{sub 4}; the later is a possible candidate as a p-type transparent conductor with potential applications in solar cells and electrochromic devices. The calculated electronic structure shows that these compounds are indirect band gap semiconductors, with the valence band maximum located at the R-point and the conduction band minimum located at the X-point. The character of the valence band maximum is dominated by Cu d-states and the character of the conduction band minimum is due to the d-states of the group five elements. From the calculated charge density and electron localisation function we can conclude that the sulvanite compounds are polar covalent semiconductors.

Genotoxicity of indium tin oxide by comet test

Directory of Open Access Journals (Sweden)

İbrahim Hakkı Ciğerci

2015-06-01

Full Text Available Indium tin oxide (ITO is used for liquid crystal display (LCDs, electrochromic displays, flat panel displays, field emission displays, touch or laptop computer screens, cell phones, energy conserving architectural windows, defogging aircraft and automobile windows, heat-reflecting coatings to increase light bulb efficiency, gas sensors, antistatic window coatings, wear resistant layers on glass, nanowires and nanorods because of its unique properties of high electrical conductivity, transparency and mechanical resistance.Genotoxic effects of ITO were investigated on the root cells of Allium cepa by Comet assay. A. cepa roots were treated with the aqueous dispersions of ITO at 5 different concentrations (12.5, 25, 50, 75, and 100 ppm for 4 h. A significant increase in DNA damage was a observed at all concentrations of ITO by Comet assay. These result indicate that ITO exhibit genotoxic activity in A. cepa root meristematic cells.

The Organic Power Transistor: Roll-to-Roll Manufacture, Thermal Behavior, and Power Handling When Driving Printed Electronics

DEFF Research Database (Denmark)

Pastorelli, Francesco; Schmidt, Thomas Mikael; Hösel, Markus

2016-01-01

to drive large currents while handling the thermal aspects in operation together with other organic printed electronics technologies such as large area organic photovoltaics (OPV)[2] and large area electrochromic displays (EC).[3] We find especially that an elevated operational temperature is beneficial...... with respect to both transconductance and on/off ratio. We achieve high currents of up to 45mA at a temperature of 80 C with an on/ off ratio of 100 which is sufficient to drive large area organic electronics such as an EC device powered by OPV devices that we also demonstrate. Finally, we observe......We present flexible organic power transistors prepared by fast (20mmin1) roll-to-roll (R2R) flexographic printing[1] of the drain (D) and source (S) electrode structures directly on polyester foil. The devices have top gate architecture and were completed by spin coating or slot-die coating...

Role of salt concentration in blend polymer for energy storage conversion devices

Energy Technology Data Exchange (ETDEWEB)

Arya, Anil; Sharma, A. L., E-mail: alsharmaiitkgp@gmail.com [Centre for Physical Sciences, Central university of Punjab, Bathinda-151001. INDIA (India); Sadiq, M. [Department of Physics, I.I.T. (BHU), Varanasi-India (India)

2016-05-06

Solid Polymer Electrolytes (SPE) are materials of considerable interest worldwide, which serves dual purpose of electrolyte and separator between electrode compartments in renewable energy conversion/storage devices such as; high energy density batteries, electrochromic display devices, and supercapacitors. Polymer blend electrolytes are prepared for various concentration of salt (Ö/Li) with the constant ratio (0.5 gm) of each PEO and PAN polymers (blend polymer) using solution casting technique. Solid polymeric ionic conductor as a separator is the ultimate substitute to eliminate the drawback related to liquid and gel polymer ionic conductors. In the present work, solid polymer electrolyte film consisting of PEO, PAN and LiPF{sub 6} are examined for various concentration of lithium salt by keeping PEO/PAN blend ratio as a constant with a view to optimize the dominant salt concentration which could give the maximum conductivity at ambient temperature.

Growth of N-substituted polypyrrole layers in ionic liquids: synthesis and its electrochromic properties

Czech Academy of Sciences Publication Activity Database

Ahmad, S.; Sen Gursoy, S.; Kazim, Samrana; Uygun, A.

2012-01-01

Roč. 99, SI (2012), s. 95-100 ISSN 0927-0248 Institutional research plan: CEZ:AV0Z40500505 Keywords : polypyrrole * substituted polypyrrole * ionic liquids Subject RIV: CD - Macromolecular Chemistry Impact factor: 4.630, year: 2012

Exploring Electrochromics: A Series of Eye-Catching Experiments to Introduce Students to Multidisciplinary Research

Science.gov (United States)

Small, Leo J.; Wolf, Steven; Spoerke, Erik D.

2014-01-01

Introducing students to a multidisciplinary research laboratory presents challenges in terms of learning specific technical skills and concepts but also with respect to integrating different technical elements to form a coherent picture of the research. Here we present a multidisciplinary series of experiments we have developed in the Electronic,…

Near-infrared selective dynamic windows controlled by charge transfer impedance at the counter electrode.

Science.gov (United States)

Pattathil, Praveen; Scarfiello, Riccardo; Giannuzzi, Roberto; Veramonti, Giulia; Sibillano, Teresa; Qualtieri, Antonio; Giannini, Cinzia; Cozzoli, P Davide; Manca, Michele

2016-12-08

Recent developments in the exploitation of transparent conductive oxide nanocrystals paved the way to the realization of a new class of electrochemical systems capable of selectively shielding the infrared heat loads carried by sunlight and prospected the blooming of a key enabling technology to be implemented in the next generation of "zero-energy" building envelopes. Here we report the fabrication of a set of electrochromic devices embodying an engineered nanostructured electrode made by high aspect-ratio tungsten oxide nanorods, which allow for selectively and dynamically controlling sunlight transmission over the near-infrared to visible range. Varying the intensity of applied voltage makes the spectral response of the device change across three different optical regimes, namely fully transparent, near-infrared only blocking and both visible and near-infrared blocking. It is demonstrated that the degree of reversible modulation of the thermal radiation entering the glazing element can approach a remarkable 85%, accompanied by only a modest reduction in the luminous transmittance.

Electrochemical DNA Hybridization Sensors Based on Conducting Polymers

Science.gov (United States)

Rahman, Md. Mahbubur; Li, Xiao-Bo; Lopa, Nasrin Siraj; Ahn, Sang Jung; Lee, Jae-Joon

2015-01-01

Conducting polymers (CPs) are a group of polymeric materials that have attracted considerable attention because of their unique electronic, chemical, and biochemical properties. This is reflected in their use in a wide range of potential applications, including light-emitting diodes, anti-static coating, electrochromic materials, solar cells, chemical sensors, biosensors, and drug-release systems. Electrochemical DNA sensors based on CPs can be used in numerous areas related to human health. This review summarizes the recent progress made in the development and use of CP-based electrochemical DNA hybridization sensors. We discuss the distinct properties of CPs with respect to their use in the immobilization of probe DNA on electrode surfaces, and we describe the immobilization techniques used for developing DNA hybridization sensors together with the various transduction methods employed. In the concluding part of this review, we present some of the challenges faced in the use of CP-based DNA hybridization sensors, as well as a future perspective. PMID:25664436

Active Plasmonics: Principles, Structures, and Applications.

Science.gov (United States)

Jiang, Nina; Zhuo, Xiaolu; Wang, Jianfang

2018-03-28

Active plasmonics is a burgeoning and challenging subfield of plasmonics. It exploits the active control of surface plasmon resonance. In this review, a first-ever in-depth description of the theoretical relationship between surface plasmon resonance and its affecting factors, which forms the basis for active plasmon control, will be presented. Three categories of active plasmonic structures, consisting of plasmonic structures in tunable dielectric surroundings, plasmonic structures with tunable gap distances, and self-tunable plasmonic structures, will be proposed in terms of the modulation mechanism. The recent advances and current challenges for these three categories of active plasmonic structures will be discussed in detail. The flourishing development of active plasmonic structures opens access to new application fields. A significant part of this review will be devoted to the applications of active plasmonic structures in plasmonic sensing, tunable surface-enhanced Raman scattering, active plasmonic components, and electrochromic smart windows. This review will be concluded with a section on the future challenges and prospects for active plasmonics.

Effects of Laser Energy Density on Size and Morphology of NiO Nanoparticles Prepared by Pulsed Laser Ablation in Liquid

Energy Technology Data Exchange (ETDEWEB)

Ma, Rory; Reddy, M. Amaranatha; Kim, Tae Kyu [Pusan National University, Busan (Korea, Republic of)

2015-01-15

Metaloxide nanoparticles are of great importance to a large variety of chemical and material applications ranging from catalysts to electronic devices. Among the metal-oxide nanoparticles, NiO is one of the technologically versatile and important semiconducting materials. It has been extensively investigated because of its myriad applications in catalysts, gas sensors, Li-ion battery materials, electrochromic coatings, active optical fibers, fuel cell electrodes, and so on. The effect of laser ablation at various laser energy densities was investigated. At low energy densities, the produced nanoparticles were of irregular morphology with an average size of 2.4 nm. At higher laser energy densities, the produced nanoparticles were spherical, with a polycrystalline structure and their average size was around 10 nm. More detailed investigations on effects of laser wavelength and energy density as well as the particle size effect on the catalytic activity of synthesized NiO nanoparticles will be investigated in future works.

Investigation of Electrical, Optical and GaS Sensing properties Sol-Gel Derived WO3 Thin Films

International Nuclear Information System (INIS)

Dumludag, F.

2008-01-01

Tungsten oxide (WO 3 ) is a wide band gap n-type semiconductor. Thin films of WO 3 are considerable interest because of their potential applications in electrochromic devices, and gas sensors. In this work, WO 3 thin films were deposited on IDT (Interdigital electrodes) by a sol-gel dipping process. Precursor solution was prepared by dissolving of tungstic acid in ammonia. We investigated d.c. and a.c. (40 Hz-100 KHz) electrical properties of the films in the temperature range of 293K and 473K in vacuum ambient (10 - 2 mbar). We observed frequency dependent conductivity behavior at high frequencies. Absorption spectra of the film showed that a maximum absorption occurred at 330 nm. We also investigated the response of the films to vapors of the volatile organic compounds (acetone, chloroform, toluene, ethanol, ammonia) and water vapor. The films showed no sensitivity to the test gases at room temperature. Concentration of the vapors were controlled by mass flowmeters. All the measurement system was computerized

Fully Roll-to-Roll Gravure Printable Wireless (13.56 MHz) Sensor-Signage Tags for Smart Packaging

Science.gov (United States)

Kang, Hwiwon; Park, Hyejin; Park, Yongsu; Jung, Minhoon; Kim, Byung Chul; Wallace, Gordon; Cho, Gyoujin

2014-01-01

Integration of sensing capabilities with an interactive signage through wireless communication is enabling the development of smart packaging wherein wireless (13.56 MHz) power transmission is used to interlock the smart packaging with a wireless (13.56 MHz) reader or a smart phone. Assembly of the necessary componentry for smart packaging on plastic or paper foils is limited by the manufacturing costs involved with Si based technologies. Here, the issue of manufacturing cost for smart packaging has been obviated by materials that allow R2R (roll-to-roll) gravure in combination with R2R coating processes to be employed. R2R gravure was used to print the wireless power transmission device, called rectenna (antenna, diode and capacitor), and humidity sensor on poly(ethylene terephtalate) (PET) films while electrochromic signage units were fabricated by R2R coating. The signage units were laminated with the R2R gravure printed rectenna and sensor to complete the prototype smart packaging. PMID:24953037

Fully Roll-to-Roll Gravure Printable Wireless (13.56 MHz) Sensor-Signage Tags for Smart Packaging

Science.gov (United States)

Kang, Hwiwon; Park, Hyejin; Park, Yongsu; Jung, Minhoon; Kim, Byung Chul; Wallace, Gordon; Cho, Gyoujin

2014-06-01

Integration of sensing capabilities with an interactive signage through wireless communication is enabling the development of smart packaging wherein wireless (13.56 MHz) power transmission is used to interlock the smart packaging with a wireless (13.56 MHz) reader or a smart phone. Assembly of the necessary componentry for smart packaging on plastic or paper foils is limited by the manufacturing costs involved with Si based technologies. Here, the issue of manufacturing cost for smart packaging has been obviated by materials that allow R2R (roll-to-roll) gravure in combination with R2R coating processes to be employed. R2R gravure was used to print the wireless power transmission device, called rectenna (antenna, diode and capacitor), and humidity sensor on poly(ethylene terephtalate) (PET) films while electrochromic signage units were fabricated by R2R coating. The signage units were laminated with the R2R gravure printed rectenna and sensor to complete the prototype smart packaging.

Structure of the short-range atomic order of WO3 amorphous films

International Nuclear Information System (INIS)

Olevskij, S.S.; Sergeev, M.S.; Tolstikhina, A.L.; Avilov, A.S.; Shkornyakov, S.M.; Semiletov, S.A.

1984-01-01

To study the causes of electrochromism manifestation in thin tungsten oxide films, the structure of WO 3 amorphous films has been investigated. The films were obtained by three different methods: by W(CO) 6 tungsten carbonyl pyrolysis, by high-frequency ion-plasma sputtering of a target prepared by WO 3 powder sintering, and by WO 3 powder thermal evaporation. Monocrystalline wafers of silicon and sodium chloride were used as substrates. The structure of short-range order in WO 3 amorphous films varies versus, the method of preparation in compliance with the type of polyhedral elements, (WO 6 , WO 5 ) and with the character of their packing (contacts via edges or vertices). Manifestation of electroc ro mism in WO 3 films prepared by varions methods and having different structure of short-range order is supposed to be realized through various mechanisms. One cannot exclude a potential simultaneous effect of the two coloration mechanisms

Synthesis of electro-optically active polymer composite of poly[2,2'-bis(3,4-ethylenedioxythiophene-alt-fluorene]/hydroxypropyl cellulose showing liquid crystal structure

Directory of Open Access Journals (Sweden)

N. Eguchi

2017-10-01

Full Text Available Electrochemical preparation of a composite consisting of poly[2,2′-bis(3,4-ethylenedioxythiophene-alt-fluorene] and hydroxypropyl cellulose (PEFE/HPC was carried out. We conducted electrochemical polymerization of poly[2,2′-bis(3,4-ethylenedioxythiophene-alt-fluorene] (EFE as a monomer in a lyotropic liquid crystal of HPC. We used an organic solvent instead of water for lyotropic liquid crystal medium to expand the possibility of the range of monomers, although water is usually employed as a solvent for HPC for showing liquid crystallinity. Here, we employed N,N-dimethylformamide (DMF as a solvent for HPC. Electrochemical polymerization in the polymer liquid crystal was carried out to obtain a polymer film with liquid crystal order. The polymer film thus prepared exhibited optical activity. Fourier transfer infrared (FT-IR absorption spectroscopy reveals that the film is a composite consisting of HPC and polymer. The composite PEFE/HPC thus prepared in HPC/DMF system showed electrochromism.

Electrochemistry, polymers and opto-electronic devices: a combination with a future

Directory of Open Access Journals (Sweden)

De Paoli Marco-A.

2002-01-01

Full Text Available Electrochemistry came into life with the invention of the pile, by Volta in 1800. He combined different metal discs with a piece of tissue, swollen with an aqueous salt solution. The so-called Pila di Volta used a polymer for the first time in an electrochemical device and can be seen as a powerful idea to create new devices. Recently, polymers became an alternative to make thin and flexible devices. Thus, we find transparent plastic electrodes based on poly(ethylene terephtalate coated with a transition metal oxide. There are also polymer electrolytes based on complexes of inorganic salts and poly(ethylene oxide derivatives, with reasonable ionic conductivity in the absence of solvents. Finally, the electroactive polymers are efficient substitutes for the inorganic semiconductors because they can be synthetically tailored to produce the desired electronic answer. Combining these materials it is possible to assemble different types of electro-optical devices, like electrochromic, photoelectrochemical and light-emitting electrochemical cells.

Assessment of Energy Impact of Window Technologies for Commercial Buildings

Energy Technology Data Exchange (ETDEWEB)

Hong, Tianzhen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Selkowitz, Stephen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division; Yazdanian, Mehry [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States). Environmental Energy Technologies Division

2009-10-01

Windows play a significant role in commercial buildings targeting the goal of net zero energy. This report summarizes research methodology and findings in evaluating the energy impact of windows technologies for commercial buildings. The large office prototypical building, chosen from the DOE commercial building benchmarks, was used as the baseline model which met the prescriptive requirements of ASHRAE Standard 90.1-2004. The building simulations were performed with EnergyPlus and TMY3 weather data for five typical US climates to calculate the energy savings potentials of six windows technologies when compared with the ASHRAE 90.1-2004 baseline windows. The six windows cover existing, new, and emerging technologies, including ASHRAE 189.1 baseline windows, triple pane low-e windows, clear and tinted double pane highly insulating low-e windows, electrochromic (EC) windows, and highly insulating EC windows representing the hypothetically feasible optimum windows. The existing stocks based on average commercial windows sales are included in the analysis for benchmarking purposes.

Large-area smart glass and integrated photovoltaics

Energy Technology Data Exchange (ETDEWEB)

Lampert, C.M. [Star Science, 8730 Water Road, Cotati, CA 94931-4252 (United States)

2003-04-01

Several companies throughout the world are developing dynamic glazing and large-area flat panel displays. University and National Laboratory groups are researching new materials and processes to improve these products. The concept of a switchable glazing for building and vehicle application is very attractive. Conventional glazing only offers fixed transmittance and control of energy passing through it. Given the wide range of illumination conditions and glare, a dynamic glazing with adjustable transmittance offers the best solution. Photovoltaics can be integrated as power sources for smart windows. In this way a switchable window could be a completely stand alone smart system. A new range of large-area flat panel display including light-weight and flexible displays are being developed. These displays can be used for banner advertising, dynamic pricing in stores, electronic paper, and electronic books, to name only a few applications. This study covers selected switching technologies including electrochromism, suspended particles, and encapsulated liquid crystals.

Electrochemical DNA Hybridization Sensors Based on Conducting Polymers

Directory of Open Access Journals (Sweden)

Md. Mahbubur Rahman

2015-02-01

Full Text Available Conducting polymers (CPs are a group of polymeric materials that have attracted considerable attention because of their unique electronic, chemical, and biochemical properties. This is reflected in their use in a wide range of potential applications, including light-emitting diodes, anti-static coating, electrochromic materials, solar cells, chemical sensors, biosensors, and drug-release systems. Electrochemical DNA sensors based on CPs can be used in numerous areas related to human health. This review summarizes the recent progress made in the development and use of CP-based electrochemical DNA hybridization sensors. We discuss the distinct properties of CPs with respect to their use in the immobilization of probe DNA on electrode surfaces, and we describe the immobilization techniques used for developing DNA hybridization sensors together with the various transduction methods employed. In the concluding part of this review, we present some of the challenges faced in the use of CP-based DNA hybridization sensors, as well as a future perspective.

Molybdenum, molybdenum oxides, and their electrochemistry.

Science.gov (United States)

Saji, Viswanathan S; Lee, Chi-Woo

2012-07-01

The electrochemical behaviors of molybdenum and its oxides, both in bulk and thin film dimensions, are critical because of their widespread applications in steels, electrocatalysts, electrochromic materials, batteries, sensors, and solar cells. An important area of current interest is electrodeposited CIGS-based solar cells where a molybdenum/glass electrode forms the back contact. Surprisingly, the basic electrochemistry of molybdenum and its oxides has not been reviewed with due attention. In this Review, we assess the scattered information. The potential and pH dependent active, passive, and transpassive behaviors of molybdenum in aqueous media are explained. The major surface oxide species observed, reversible redox transitions of the surface oxides, pseudocapacitance and catalytic reduction are discussed along with carefully conducted experimental results on a typical molybdenum glass back contact employed in CIGS-based solar cells. The applications of molybdenum oxides and the electrodeposition of molybdenum are briefly reviewed. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

The fabrication and characterization of inkjet-printed polyaniline nanoparticle films

International Nuclear Information System (INIS)

Morrin, Aoife; Ngamna, Orawan; O'Malley, Eimer; Kent, Nigel; Moulton, Simon E.; Wallace, Gordon G.; Smyth, Malcolm R.; Killard, Anthony J.

2008-01-01

This paper reports on the fabrication and characterization of electrodes modified with conducting polymer nanoparticle films, produced via inkjet printing. The polyaniline nanoparticle formulations were deposited via a desktop inkjet printer onto screen-printed carbon-paste electrodes (SPE), polyethylene terephthalate (PET) and gold-PET and their morphology studied at a range of length scales using profilometry, scanning electron microscopy and atomic force microscopy. The deposited films were found to form continuous polymer films depending upon film thickness, which was in turn dependent on the number of prints performed. The inkjet-printed films exhibited a smooth morphology on the SPEs at the micro-dimensional scale, as a result of the aggradation and coalescing of the nanoparticles upon deposition. The resulting modified electrodes were both conductive and electroactive, possessing good reversible polyaniline electrochemistry. Such a combination of materials and processing offers the potential of producing a range of low cost, solid state devices such as sensors, actuators and electrochromic devices

Conducting polymers of octanoic acid 2-thiophen-3-yl-ethyl ester and their electrochromic properties

International Nuclear Information System (INIS)

Camurlu, Pinar; Cirpan, Ali; Toppare, Levent

2005-01-01

Octanoic acid 2-thiophen-3-yl-ethyl ester was synthesized via the reaction of 3-thiophene ethanol with octanoyl chloride. The resulting monomer was electrochemically homopolymerized in the presence of tetrabutylammonium tetrafluoroborate as the supporting electrolyte, in the acetonitrile/borontrifluoride ethyl ether solvent system. The resulting polymer was characterized using various experimental techniques. Spectroelectrochemistry analysis of the homopolymer reflects electronic transitions at 434, ∼800 and ∼1100 nm, revealing π-π* transition, polaron and bipolaron band formation, respectively, leading to esthetically pleasing color changes between transmissive yellow and blue, with reasonable switching times

Evaluation of the Intramolecular Charge-Transfer Properties in Solvatochromic and Electrochromic Zinc Octa(carbazolyl)phthalocyanines.

Science.gov (United States)

Majeed, Shereen A; Ghazal, Basma; Nevonen, Dustin E; Goff, Philip C; Blank, David A; Nemykin, Victor N; Makhseed, Saad

2017-10-02

2,3,9,10,16,17,23·24-Octakis-(9H-carbazol-9-yl) phthalocyaninato zinc(II) (3) and 2,3,9,10,16,17,23·24-octakis-(3,6-di-tert-butyl-9H-carbazole) phthalocyaninato zinc(II) (4) complexes were prepared and characterized by NMR and UV-vis spectroscopies, magnetic circular dichroism (MCD), matrix-assisted laser desorption ionization mass spectrometry, and X-ray crystallography. UV-vis and MCD data are indicative of the interligand charge-transfer nature of the broad band observed in 450-500 nm range for 3 and 4. The redox properties of 3 and 4 were probed by electrochemical and spectro-electrochemical methods, which are suggestive of phthalocyanine-centered first oxidation and reduction processes. Photophysics of 3 and 4 were investigated by steady-state fluorescence and time-resolved transient absorption spectroscopy demonstrating the influence of the carbazole substituents on deactivation from the first excited state in 3 and 4. Protonation of the meso-nitrogen atoms in 3 results in much faster deactivation kinetics from the first excited state. Spectroscopic data were correlated with density functional theory (DFT) and time-dependent DFT calculations on 3 and 4.

Electrochromic devices based on wide band-gap nanocrystalline semiconductors functionalized with mononuclear charge transfer compounds

DEFF Research Database (Denmark)

Biancardo, M.; Argazzi, R.; Bignozzi, C.A.

2006-01-01

A series of ruthenium and iron mononuclear complexes were prepared and their spectroeletrochemical behavior characterized oil Optically Transparent Thin Layer Electrodes (OTTLE) and on Fluorine Doped SnO2 (FTO) conductive glasses coated with Sb-doped nanocrystalline SnO2. These systems display a ...

Morphological control of Ni/NiO core/shell nanoparticles and production of hollow NiO nanostructures

International Nuclear Information System (INIS)

Chopra, Nitin; Claypoole, Leslie; Bachas, Leonidas G.

2010-01-01

Chemical synthesis coupled with a microwave irradiation process allowed for the control of size (6-40 nm), shape, and shell thickness of Ni/NiO core/shell nanoparticles. In this unique synthetic route, the size of Ni nanoparticles (NiNPs) was strongly influenced by the nickel salt-to-stabilizer ratio and the amount of the stabilizer. Interestingly, it was observed that the shape of the nanoparticles was altered by varying the reaction time, where longer reaction times resulted in annealing effects and rupture of the stabilizer micelle leading to distinct shapes of Ni/NiO core/shell nanostructures. Product cooling rate was another important parameter identified in this study that not only affected the shape, but also the crystal structure of the core/shell nanoparticles. In addition, a simple and cost-effective method of microwave irradiation of NiNPs led to the formation of distinctly shaped hollow NiO nanoparticles. These high surface area core/shell nanoparticles with well-controlled morphologies are important and can lead to significant advancement in the design of improved fuel cells, electrochromic display devices, and catalysis systems.

Inert Layered Silicate Improves the Electrochemical Responses of a Metal Complex Polymer.

Science.gov (United States)

Eguchi, Miharu; Momotake, Masako; Inoue, Fumie; Oshima, Takayoshi; Maeda, Kazuhiko; Higuchi, Masayoshi

2017-10-11

A chemically inert, insulating layered silicate (saponite; SP) and an iron(II)-based metallo-supramolecular complex polymer (polyFe) were combined via electrostatic attraction to improve the electrochromic properties of polyFe. Structural characterization indicated that polyFe was intercalated into the SP nanosheets. Interestingly, the redox potential of polyFe was lowered by combining it with SP, and the current was measurable despite the insulating nature of SP. X-ray photoelectron spectroscopy showed that the decrease in the redox potential observed in the SP-polyFe hybrid was caused by the electrostatic neutralization of the Fe cation in polyFe by the negative charge on SP. Electrochemical analyses indicated that electron transfer occurred through electron hopping across the SP-polyFe hybrid. Control experiments using a metal complex composed of Fe and two 2,2':6',2''-terpyridine ligands (terpyFe) showed that SP contributes to the effective electron hopping. This modulation of the electrochemical properties by the layered silicates could be applied to other electrochemical systems, including hybrids of the redox-active ionic species and ion-exchangeable adsorbents.

Raman studies of hexagonal MoO{sub 3} at high pressure

Energy Technology Data Exchange (ETDEWEB)

Zhang, C.C.; Zhang, Z.M.; Dai, R.C.; Zhang, J.W.; Ding, Z.J. [Hefei National Laboratory for Physical Sciences at Microscale, Department of Physics, University of Science and Technology of China, Hefei, Anhui 230026 (China); Zheng, L. [Department of Nanomaterials and Nanochemistry, Hefei National Laboratory for Physical Sciences at Microscale, University of Science and Technology of China, Hefei, Anhui 230026 (China); Wang, Z.P. [The Centre for Physical Experiments, University of Science and Technology of China, Hefei, Anhui 230026 (China)

2011-05-15

The transition-metal oxide MoO{sub 3} is an important semiconductor and has various technological applications in catalysts, electrochromic and photochromic devices, gas sensors, and battery electrodes. In this study, the hexagonal MoO{sub 3} prepared by a hydrothermal method is in morphology of microrod with diameter of 0.8-1.2 {mu}m and length of 2.0-4.3 {mu}m. Its structural stability was investigated by an in situ Raman scattering method in a diamond anvil cell up to 28.7 GPa at room temperature. The new Raman peak around 1000 cm{sup -1} implies that a phase transition from hexagonal to amorphous starts at 5.6 GPa, and the evolution of the Raman spectra indicates that the structural transition is completed at about 13.2 GPa. After releasing pressure to ambient condition, the Raman spectrum pattern of the high pressure phase was retained, revealing that the phase transition is irreversible. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Towards flexible solid-state supercapacitors for smart and wearable electronics.

Science.gov (United States)

Dubal, Deepak P; Chodankar, Nilesh R; Kim, Do-Heyoung; Gomez-Romero, Pedro

2018-03-21

Flexible solid-state supercapacitors (FSSCs) are frontrunners in energy storage device technology and have attracted extensive attention owing to recent significant breakthroughs in modern wearable electronics. In this study, we review the state-of-the-art advancements in FSSCs to provide new insights on mechanisms, emerging electrode materials, flexible gel electrolytes and novel cell designs. The review begins with a brief introduction on the fundamental understanding of charge storage mechanisms based on the structural properties of electrode materials. The next sections briefly summarise the latest progress in flexible electrodes (i.e., freestanding and substrate-supported, including textile, paper, metal foil/wire and polymer-based substrates) and flexible gel electrolytes (i.e., aqueous, organic, ionic liquids and redox-active gels). Subsequently, a comprehensive summary of FSSC cell designs introduces some emerging electrode materials, including MXenes, metal nitrides, metal-organic frameworks (MOFs), polyoxometalates (POMs) and black phosphorus. Some potential practical applications, such as the development of piezoelectric, photo-, shape-memory, self-healing, electrochromic and integrated sensor-supercapacitors are also discussed. The final section highlights current challenges and future perspectives on research in this thriving field.

Switchable Materials for Smart Windows.

Science.gov (United States)

Wang, Yang; Runnerstrom, Evan L; Milliron, Delia J

2016-06-07

This article reviews the basic principles of and recent developments in electrochromic, photochromic, and thermochromic materials for applications in smart windows. Compared with current static windows, smart windows can dynamically modulate the transmittance of solar irradiation based on weather conditions and personal preferences, thus simultaneously improving building energy efficiency and indoor human comfort. Although some smart windows are commercially available, their widespread implementation has not yet been realized. Recent advances in nanostructured materials provide new opportunities for next-generation smart window technology owing to their unique structure-property relations. Nanomaterials can provide enhanced coloration efficiency, faster switching kinetics, and longer lifetime. In addition, their compatibility with solution processing enables low-cost and high-throughput fabrication. This review also discusses the importance of dual-band modulation of visible and near-infrared (NIR) light, as nearly 50% of solar energy lies in the NIR region. Some latest results show that solution-processable nanostructured systems can selectively modulate the NIR light without affecting the visible transmittance, thus reducing energy consumption by air conditioning, heating, and artificial lighting.

Hot-wire chemical vapor synthesis for a variety of nano-materials with novel applications

International Nuclear Information System (INIS)

Dillon, A.C.; Mahan, A.H.; Deshpande, R.; Alleman, J.L.; Blackburn, J.L.; Parillia, P.A.; Heben, M.J.; Engtrakul, C.; Gilbert, K.E.H.; Jones, K.M.; To, R.; Lee, S-H.; Lehman, J.H.

2006-01-01

Hot-wire chemical vapor deposition (HWCVD) has been demonstrated as a simple economically scalable technique for the synthesis of a variety of nano-materials in an environmentally friendly manner. For example we have employed HWCVD for the continuous production of both carbon single- and multi-wall nanotubes (SWNTs and MWNTs). Unanticipated hydrogen storage on HWCVD-generated MWNTs has led insight into the adsorption mechanism of hydrogen on metal/carbon composites at near ambient temperatures that could be useful for developing a vehicular hydrogen storage system. Recent efforts have been focused on growing MWNT arrays on thin nickel films with a simple HWCVD process. New data suggests that these MWNT arrays could replace the gold black coatings currently used in pyroelectric detectors to accurately measure laser power. Finally, we have very recently employed HWCVD for the production of crystalline molybdenum and tungsten oxide nanotubes and nanorods. These metal oxide nanorods and nanotubes could have applications in catalysis, batteries and electrochromic windows or as gas sensors. A summary of the techniques for growing these novel materials and their various potential applications is provided

Multifunctional Energy Storage and Conversion Devices.

Science.gov (United States)

Huang, Yan; Zhu, Minshen; Huang, Yang; Pei, Zengxia; Li, Hongfei; Wang, Zifeng; Xue, Qi; Zhi, Chunyi

2016-10-01

Multifunctional energy storage and conversion devices that incorporate novel features and functions in intelligent and interactive modes, represent a radical advance in consumer products, such as wearable electronics, healthcare devices, artificial intelligence, electric vehicles, smart household, and space satellites, etc. Here, smart energy devices are defined to be energy devices that are responsive to changes in configurational integrity, voltage, mechanical deformation, light, and temperature, called self-healability, electrochromism, shape memory, photodetection, and thermal responsivity. Advisable materials, device designs, and performances are crucial for the development of energy electronics endowed with these smart functions. Integrating these smart functions in energy storage and conversion devices gives rise to great challenges from the viewpoint of both understanding the fundamental mechanisms and practical implementation. Current state-of-art examples of these smart multifunctional energy devices, pertinent to materials, fabrication strategies, and performances, are highlighted. In addition, current challenges and potential solutions from materials synthesis to device performances are discussed. Finally, some important directions in this fast developing field are considered to further expand their application. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Flexible power fabrics made of carbon nanotubes for harvesting thermoelectricity.

Science.gov (United States)

Kim, Suk Lae; Choi, Kyungwho; Tazebay, Abdullah; Yu, Choongho

2014-03-25

Thermoelectric energy conversion is very effective in capturing low-grade waste heat to supply electricity particularly to small devices such as sensors, wireless communication units, and wearable electronics. Conventional thermoelectric materials, however, are often inadequately brittle, expensive, toxic, and heavy. We developed both p- and n-type fabric-like flexible lightweight materials by functionalizing the large surfaces and junctions in carbon nanotube (CNT) mats. The poor thermopower and only p-type characteristics of typical CNTs have been converted into both p- and n-type with high thermopower. The changes in the electronic band diagrams of the CNTs were experimentally investigated, elucidating the carrier type and relatively large thermopower values. With our optimized device design to maximally utilize temperature gradients, an electrochromic glucose sensor was successfully operated without batteries or external power supplies, demonstrating self-powering capability. While our fundamental study provides a method of tailoring electronic transport properties, our device-level integration shows the feasibility of harvesting electrical energy by attaching the device to even curved surfaces like human bodies.

Investigation of the impacts of selected nanotechnology products with view to their demand for raw materials and energy

International Nuclear Information System (INIS)

Möller, M; Manhart, A; Diesner, M; Küppers, P; Spieth-Achtnich, A; Pistner, C

2014-01-01

In the study presented here qualitative and quantitative life-cycle considerations were employed to assess the potential material and energy savings that might be achieved through nanoenabled applications. Ten nanotechnology application fields with broad market coverage and immediate impact to either the generation of renewable energies or the use of critical resources were analyzed. Organic photovoltaic modules (solar cells that essentially consist of organic materials) and electronically dimmable windows (electrochromic laminated glass, which can be adjusted to conform to the ambient light conditions) as two very promising nano-enabled applications were quantitatively analyzed. Eight further products including neodymium magnets were evaluated on a qualitative basis. All assessments contain classical indicators such as energy efficiency, product carbon footprint, and resource consumption. In addition, pollutant aspects (exposure and toxicology) as well as other sustainability aspects (such as user benefits) were taken into account in the framework of a so-called 'hot spot analysis'. Furthermore, drivers behind the innovation as well as associated rebound effects were identified. The results highlight the importance of product specific analyses based on a life-cycle thinking approach

Materials space of solid-state electrolytes: unraveling chemical composition-structure-ionic conductivity relationships in garnet-type metal oxides using cheminformatics virtual screening approaches.

Science.gov (United States)

Kireeva, Natalia; Pervov, Vladislav S

2017-08-09

The organic electrolytes of most current commercial rechargeable Li-ion batteries (LiBs) are flammable, toxic, and have limited electrochemical energy windows. All-solid-state battery technology promises improved safety, cycling performance, electrochemical stability, and possibility of device miniaturization and enables a number of breakthrough technologies towards the development of new high power and energy density microbatteries for electronics with low processing cost, solid oxide fuel cells, electrochromic devices, etc. Currently, rational materials design is attracting significant attention, which has resulted in a strong demand for methodologies that can accelerate the design of materials with tailored properties; cheminformatics can be considered as an efficient tool in this respect. This study was focused on several aspects: (i) identification of the parameters responsible for high Li-ion conductivity in garnet structured oxides; (ii) development of quantitative models to elucidate composition-structure-Li ionic conductivity relationships, taking into account the experimental details of sample preparation; (iii) circumscription of the materials space of solid garnet-type electrolytes, which is attractive for virtual screening. Several candidate compounds have been recommended for synthesis as potential solid state electrolyte materials.

Applications of inorganic Ion-conductor

Energy Technology Data Exchange (ETDEWEB)

Fujiki, Yoshinori [Science and Technology Agency, Tokyo (Japan)

1989-03-01

Physical properties and application of solid electrolyte, particularly of inorganic solid electrolyte, are described. Ion conductors have been widely used not only for electric power application but also for sensors, gas separators, display elements, Coulomb meters, storage elements, etc. The most extensively used pacemakers now employ Li/I{sub 2}(PVP) primary batteries. Thin film lithium secondary battery has a feature of providing comparatively large electric current, with 2.5 V charging, 1.8 V discharging, and 3 mA.cm{sup {minus}2} short circuit current. The capacity of about 4 mAh per 1 cm{sup 2} electrode has been achieved. The most widely used solid electrolyte for the oxygen sensor is the stabilized ZrO{sub 2}. The relation of air/fuel mix proportion with the change in electromotive force is shown. Although solid electrolyte fuel cell is not yet put to practical use, a result of an experiment is introduced. Brief explanations are made on the oxygen pump, electrochromic display elements, Coulomb meter and voltage storage element. 18 refs., 11 figs., 6 tabs.

Morphological control of Ni/NiO core/shell nanoparticles and production of hollow NiO nanostructures

Energy Technology Data Exchange (ETDEWEB)

Chopra, Nitin [University of Alabama, Department of Metallurgical and Materials Engineering, Center for Materials for Information Technology (MINT) (United States); Claypoole, Leslie [Fairmont State University (United States); Bachas, Leonidas G., E-mail: bachas@uky.ed [University of Kentucky, Department of Chemistry (United States)

2010-10-15

Chemical synthesis coupled with a microwave irradiation process allowed for the control of size (6-40 nm), shape, and shell thickness of Ni/NiO core/shell nanoparticles. In this unique synthetic route, the size of Ni nanoparticles (NiNPs) was strongly influenced by the nickel salt-to-stabilizer ratio and the amount of the stabilizer. Interestingly, it was observed that the shape of the nanoparticles was altered by varying the reaction time, where longer reaction times resulted in annealing effects and rupture of the stabilizer micelle leading to distinct shapes of Ni/NiO core/shell nanostructures. Product cooling rate was another important parameter identified in this study that not only affected the shape, but also the crystal structure of the core/shell nanoparticles. In addition, a simple and cost-effective method of microwave irradiation of NiNPs led to the formation of distinctly shaped hollow NiO nanoparticles. These high surface area core/shell nanoparticles with well-controlled morphologies are important and can lead to significant advancement in the design of improved fuel cells, electrochromic display devices, and catalysis systems.

Structural and optical properties of electrodeposited molybdenum oxide thin films

International Nuclear Information System (INIS)

Patil, R.S.; Uplane, M.D.; Patil, P.S.

2006-01-01

Electrosynthesis of Mo(IV) oxide thin films on F-doped SnO 2 conducting glass (10-20/Ω/□) substrates were carried from aqueous alkaline solution of ammonium molybdate at room temperature. The physical characterization of as-deposited films carried by thermogravimetric/differential thermogravimetric analysis (TGA/DTA), infrared spectroscopy and X-ray diffraction (XRD) showed the formation of hydrous and amorphous MoO 2 . Scanning electron microscopy (SEM) revealed a smooth but cracked surface with multi-layered growth. Annealing of these films in dry argon at 450 deg. C for 1 h resulted into polycrystalline MoO 2 with crystallites aligned perpendicular to the substrate. Optical absorption study indicated a direct band gap of 2.83 eV. The band gap variation consistent with Moss rule and band gap narrowing upon crystallization was observed. Structure tailoring of as-deposited thin films by thermal oxidation in ambient air to obtain electrochromic Mo(VI) oxide thin films was exploited for the first time by this novel route. The results of this study will be reported elsewhere

Synthesis and electrochemical characterization of new optoelectronic materials based on conjugated donor-acceptor system containing oligo-tri(heteroaryl)-1,3,5-triazines

International Nuclear Information System (INIS)

Idzik, Krzysztof R.; Rapta, Peter; Cywinski, Piotr J.; Beckert, Rainer; Dunsch, Lothar

2010-01-01

A series of novel oligoarylenes based on donor-acceptor system, containing triazine moiety as an electron-transporting central core, have been prepared by electrochemical polymerization. The redox behaviour of poly(2,4,6-tri[p-(2-(3,4-ethylenedioxythienyl))-phenyl]-1,3,5-triazine) was studied by cyclic voltammetry and triple in situ ESR/UV-vis-NIR spectroelectrochemistry to get more details on the type of charge carriers within the film. To obtain desired oligoarylenes, triazine-core monomers possessing various electrochromic side groups have been synthesized by the Stille cross-coupling methodology. The structures have been confirmed by 1 H NMR, 13 C NMR, and elemental analysis. Monomers show good chemical stability in common organic solvents such as chloroform, dichloromethane or toluene and also exhibit excellent thermal stability over wide range of temperatures. Furthermore, their photophysical properties have been established with the use of fluorescence spectroscopy. Electrochemical results accompanied with fluorescence spectroscopy suggest that these derivatives of triazine can be successfully used in the fabrication of organic light-emitting diodes (OLEDs).

Electroabsorption spectra of carotenoid isomers: Conformational modulation of polarizability vs. induced dipole moments

International Nuclear Information System (INIS)

Krawczyk, Stanislaw; Jazurek, Beata; Luchowski, Rafal; Wiacek, Dariusz

2006-01-01

Electroabsorption spectra of all-trans, 13-cis and 15-cis isomers of carotenoids violaxanthin and β-carotene frozen in organic solvents were analysed in terms of changes in permanent dipole moment, Δμ, and in the linear polarizability, Δα, on electronic excitation. The spectral range investigated covered the two carotenoid absorption bands in the VIS and UV, known to originate from differently oriented transition dipole moments. In contrast with the collinearity of the apparent Δμ with Δα in the lowest-energy allowed (VIS) transition 1A g - ->1B u + , the axis of the largest polarizability change in the UV transition 1A g - ->1A g + (''cis band'') was found to make a large angle with the transition moment, while the direction of Δμ appears to be much closer to it. These data support the view that Δμ's inferred from electrochromic spectra of carotenoids are apparent and are not induced by the local matrix field in the solvent cavity, but merely result from conformational modulation of molecular polarizability

Manufacture and demonstration of organic photovoltaic-powered electrochromic displays using roll coating methods and printable electrolytes

DEFF Research Database (Denmark)

Jensen, Jacob; Dam, Henrik Friis; Reynolds, John R.

2012-01-01

active material (ECP-Magenta) and poly(N-octadecyl-(propylene-1,3-dioxy)-3,4-pyrrole-2,5-diyl) as a minimally colored, charge balancing material (MCCP). Two electrolyte systems were compared to allow development of fully printable and laminated devices on flexible substrates. Devices of various sizes, up...... to 7 × 8 cm2, are demonstrated with pixelated devices containing pixel sizes of 4 × 4 mm2 or 13 × 13 mm2. The transmission contrast exhibited by the devices, when switched between the fully bleached and fully colored state, was 58% at a visible wavelength of 550 nm, and the devices exhibited switching...... times of photovoltaic devices (with or without the use of a lithium-polymer battery) to power the devices between the colored and bleached state, illustrating a self-powered ECD. © 2012 Wiley Periodicals, Inc. J Polym Sci Part B...

Understanding the conductive channel evolution in Na:WO3-x-based planar devices

Science.gov (United States)

Shang, Dashan; Li, Peining; Wang, Tao; Carria, Egidio; Sun, Jirong; Shen, Baogen; Taubner, Thomas; Valov, Ilia; Waser, Rainer; Wuttig, Matthias

2015-03-01

An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO3-x) films on a soda-lime glass substrate, from which Na+ diffuses into the WO3-x films during the deposition. The entire process of Na+ migration driven by an alternating electric field is visualized in the Na-doped WO3-x films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the devices. The peculiar channel evolution is interpreted by a thermal-stress-induced mechanical deformation of the films and an asymmetric Na+ mobility between the parabolic and the bar channels. These results exemplify a typical ion migration process driven by an alternating electric field in a solid electrolyte with a low ion mobility and are expected to be beneficial to improve the controllability of the ion migration in ion-based functional devices, such as resistive switching devices.An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO3-x) films on a soda-lime glass substrate, from which Na+ diffuses into the WO3-x films during the deposition. The entire process of Na+ migration driven by an alternating electric field is visualized in the Na-doped WO3-x films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the

Research and development of utilization technology of solar thermal system for industrial and other use. Development of passive solar system (research and development of advanced glazing); Sangyoyo nado solar system jitsuyoka gijutsu kaihatsu. Passive solar system no kaihatsu (chokozai nado no kenkyu kaihatsu (advanced grazing no kenkyu kaihatsu))

Energy Technology Data Exchange (ETDEWEB)

Takita, M [New Energy and Industrial Technology Development Organization, Tokyo (Japan)

1994-12-01

Described herein are the results of the FY1994 research program for advanced glazing in which solar energy is efficiently utilized. The peripheral techniques are surveyed for evaluation of characteristics of large-size dimming glass, optimization of film compositions and scaling up. The dimming device, made on a trial basis, attains a target controllable rage of at least 50% for visible light transmittance. The suitable components include WO3 as the electrochromic material producing color under a reducing atmosphere, NiO as the counter electrode producing color under an oxidative atmosphere, and hydrated SbOx as the proton-conducting electrolyte. The test results indicate possibility of the dimming glass stably operable while being irradiated with a quantity of sun ray of around 10 years. The study on scaling up the dimmer glass develops, on a trial basis, a process for producing large-size glass and evaluates its characteristics, where the film parameters are investigated. It also investigates the peripheral techniques for assembling the devices for the large-size glass, and develops useful techniques, such as those for sealants and improved sealing methods. 1 fig., 1 tab.

Technologies for deposition of transition metal oxide thin films: application as functional layers in “Smart windows” and photocatalytic systems

Science.gov (United States)

Gesheva, K.; Ivanova, T.; Bodurov, G.; Szilágyi, I. M.; Justh, N.; Kéri, O.; Boyadjiev, S.; Nagy, D.; Aleksandrova, M.

2016-02-01

“Smart windows” are envisaged for future low-energy, high-efficient architectural buildings, as well as for the car industry. By switching from coloured to fully bleached state, these windows regulate the energy of solar flux entering the interior. Functional layers in these devices are the transition metals oxides. The materials (transitional metal oxides) used in smart windows can be also applied as photoelectrodes in water splitting photocells for hydrogen production or as photocatalytic materials for self-cleaning surfaces, waste water treatment and pollution removal. Solar energy utilization is recently in the main scope of numerous world research laboratories and energy organizations, working on protection against conventional fuel exhaustion. The paper presents results from research on transition metal oxide thin films, fabricated by different methods - atomic layer deposition, atmospheric pressure chemical vapour deposition, physical vapour deposition, and wet chemical methods, suitable for flowthrough production process. The lower price of the chemical deposition processes is especially important when the method is related to large-scale glazing applications. Conclusions are derived about which processes are recently considered as most prospective, related to electrochromic materials and devices manufacturing.

Effects of a base coating used for electropolymerization of poly(3,4-ethylenedioxythiophene) on indium tin oxide electrode

International Nuclear Information System (INIS)

Wang, X.J.; Wong, K.Y.

2006-01-01

Electropolymerization of poly(3,4-ethylenedioxythiophene) (PEDOT) films on indium tin oxide (ITO), using a very thin PEDOT:poly(styrene sulfonate) (PEDOT:PSS) film as a base coating, was carried out in a non-aqueous solution containing the monomer, an electrolyte and propylene carbonate by a two-electrode system. For comparison, PEDOT film electrodeposited on bare ITO substrate under the same condition was also presented. The PEDOT films deposited on these two substrates were characterized by scanning electron microscopy, energy disperse X-ray spectroscopy and Raman spectroscopy. The results indicate that the PEDOT film electrodeposited on bare ITO was not uniform, while the PEDOT film electrodeposited on PEDOT:PSS/ITO has better uniformity. The compositions of the different regions of PEDOT film electrodeposited on bare ITO and PEDOT:PSS/ITO were studied and discussed. Electrochromic devices (ECDs) based on PEDOT films electrodeposited on bare ITO and PEDOT:PSS/ITO were fabricated and characterized by UV-Vis-NIR spectrophotometric study. The results show that the display contrast of the ECD based on PEDOT film electrodeposited on PEDOT:PSS/ITO was improved over that on a bare ITO substrate

Preparation and characterization of polyindole - iron oxide nanocomposite electrolyte

International Nuclear Information System (INIS)

Rajasudha, G.; Stephen, A.; Narayanan, V.

2009-01-01

Full text: A novel polyindole-iron oxide containing LiClO 4 solid polymer electrolyte has been prepared. The diverse property of magnetic nanoparticle has elicited wide interest from the point of view of technological applications. Their properties are known to be strongly dependent on size, anisotropy and inter particle interactions. The proton conducting materials has received considerable attention as electrolyte materials in technological applications such as fuel cells, sensors and electrochromic display. In this work, polyindole-iron oxide nanocomposite containing LiClO 4 was prepared by in situ polymerization. The indole was polymerized in the presence of iron oxide, using ammonium peroxy disulphate as an oxidizing agent. The polyindole-iron oxide nanocomposite was characterized by XRD, IR, SEM, TGA and TEM. The iron oxide nano particles was incorporated into polyindole and was confirmed by XRD and Fourier transform infrared (FTIR) spectroscopy. The surface Morphology and thermal stability were studied by thermogravimetric analysis (TGA) and SEM respectively. The ionic conductivity of polyindole electrolyte was analyzed from impedance spectrum. The prepared polyindole-iron oxide nanocomposite could be used as solid electrolyte in lithium ion batteries

Latest advances in supercapacitors: from new electrode materials to novel device designs.

Science.gov (United States)

Wang, Faxing; Wu, Xiongwei; Yuan, Xinhai; Liu, Zaichun; Zhang, Yi; Fu, Lijun; Zhu, Yusong; Zhou, Qingming; Wu, Yuping; Huang, Wei

2017-11-13

Notably, many significant breakthroughs for a new generation of supercapacitors have been reported in recent years, related to theoretical understanding, material synthesis and device designs. Herein, we summarize the state-of-the-art progress toward mechanisms, new materials, and novel device designs for supercapacitors. Firstly, fundamental understanding of the mechanism is mainly focused on the relationship between the structural properties of electrode materials and their electrochemical performances based on some in situ characterization techniques and simulations. Secondly, some emerging electrode materials are discussed, including metal-organic frameworks (MOFs), covalent organic frameworks (COFs), MXenes, metal nitrides, black phosphorus, LaMnO 3 , and RbAg 4 I 5 /graphite. Thirdly, the device innovations for the next generation of supercapacitors are provided successively, mainly emphasizing flow supercapacitors, alternating current (AC) line-filtering supercapacitors, redox electrolyte enhanced supercapacitors, metal ion hybrid supercapacitors, micro-supercapacitors (fiber, plane and three-dimensional) and multifunctional supercapacitors including electrochromic supercapacitors, self-healing supercapacitors, piezoelectric supercapacitors, shape-memory supercapacitors, thermal self-protective supercapacitors, thermal self-charging supercapacitors, and photo self-charging supercapacitors. Finally, the future developments and key technical challenges are highlighted regarding further research in this thriving field.

Lithium intercalation in sputter deposited antimony-doped tin oxide thin films: Evidence from electrochemical and optical measurements

Energy Technology Data Exchange (ETDEWEB)

Montero, J., E-mail: jose.montero@angstrom.uu.se; Granqvist, C. G.; Niklasson, G. A. [Department of Engineering Sciences, The A°ngström Laboratory, Uppsala University, P.O. Box 534, SE-751 21 Uppsala (Sweden); Guillén, C.; Herrero, J. [Department of Energy, Ciemat, Avda. Complutense 40, Ed. 42, E-28040 Madrid (Spain)

2014-04-21

Transparent conducting oxides are used as transparent electrical contacts in a variety of applications, including in electrochromic smart windows. In the present work, we performed a study of transparent conducting antimony-doped tin oxide (ATO) thin films by chronopotentiometry in a Li{sup +}-containing electrolyte. The open circuit potential vs. Li was used to investigate ATO band lineups, such as those of the Fermi level and the ionization potential, as well as the dependence of these lineups on the preparation conditions for ATO. Evidence was found for Li{sup +} intercalation when a current pulse was set in a way so as to drive ions from the electrolyte into the ATO lattice. Galvanostatic intermittent titration was then applied to determine the lithium diffusion coefficient within the ATO lattice. The electrochemical density of states of the conducting oxide was studied by means of the transient voltage recorded during the chronopotentiometry experiments. These measurements were possible because, as Li{sup +} intercalation took place, charge compensating electrons filled the lowest part of the conduction band in ATO. Furthermore, the charge insertion modified the optical properties of ATO according to the Drude model.

CHARACTERISTICS OF LITHIUM LANTHANUM TITANATE THIN FILMS MADE BY ELECTRON BEAM EVAPORATION FROM NANOSTRUCTURED La0.67-xLi 3xTiO3 TARGET

Directory of Open Access Journals (Sweden)

Nguyen Nang Dinh

2017-11-01

Full Text Available Bulk nanostructured perovskites of La0.67-xLi3xTiO3 (LLTO were prepared by using thermally ball-grinding from compounds of La2O3, Li2CO3 and TiO2. From XRD analysis, it was found that LTTO materials were crystallized with nano-size grains of an average size of 30 nm. The bulk ionic conductivity was found strongly dependent on the Li+ composition, the samples with x = 0.11 (corresponding to a La0.56Li0.33TiO3 compound have the best ionic conductivity, which is ca. 3.2 x 10-3 S/cm at room temperature. The LLTO amorphous films were made by electron beam deposition. At room temperature the smooth films have ionic conductivity of 3.5 x 10-5  S/cm and transmittance of 80%. The optical bandgap of the films was found to be of 2.3 eV. The results have shown that the perovskite La0.56Li0.33TiO3  thin films can be used for a transparent solid electrolyte in ionic battery and in all-solid-state electrochromic devices, in particular.

Structural and optical properties of sol-gel deposited proton conducting Ta{sub 2}O{sub 5} films

Energy Technology Data Exchange (ETDEWEB)

Ozer, N.; Lampert, C.M.

1995-08-01

Proton conducting tantalum oxide films were deposited by spin coating using a sol-gel process. The coating solutions were prepared using Ta(OC{sub 2}H{sub 5}){sub 5} as a precursor. X-ray diffraction studies determined that the sol-gel films, heat treated at temperatures below 400 C, were amorphous. Films heat treated at higher temperatures were crystalline Ta{sub 2}O{sub 5}. The solar transmission values (T{sub s}) of tantala films on glass generally range from 0.8--0.9 depending on thickness. The refractive index and the extinction coefficient were evaluated from transmittance characteristics in the UV-VIS-NIR regions. The refractive index values calculated at 550 nm increased from 1.78 to 1.97 with increasing heat treatment from 150 to 450 C. The films heat treated at different temperatures showed low absorption with extinction coefficients of less than k=1x10{sup -3} in the visible range. Spectrophotometric and impedance spectroscopic investigations performed on Ta{sub 2}O{sub 5} films revealed that these films have protonic conductivity of 3.2x10{sup -6} S/cm. The films are suitable for proton conducting layers in electrochromic (EC) devices.

Technologies for deposition of transition metal oxide thin films: application as functional layers in “Smart windows” and photocatalytic systems

International Nuclear Information System (INIS)

Gesheva, K; Ivanova, T; Bodurov, G; Szilágyi, I M; Justh, N; Kéri, O; Boyadjiev, S; Nagy, D; Aleksandrova, M

2016-01-01

“Smart windows” are envisaged for future low-energy, high-efficient architectural buildings, as well as for the car industry. By switching from coloured to fully bleached state, these windows regulate the energy of solar flux entering the interior. Functional layers in these devices are the transition metals oxides. The materials (transitional metal oxides) used in smart windows can be also applied as photoelectrodes in water splitting photocells for hydrogen production or as photocatalytic materials for self-cleaning surfaces, waste water treatment and pollution removal. Solar energy utilization is recently in the main scope of numerous world research laboratories and energy organizations, working on protection against conventional fuel exhaustion. The paper presents results from research on transition metal oxide thin films, fabricated by different methods - atomic layer deposition, atmospheric pressure chemical vapour deposition, physical vapour deposition, and wet chemical methods, suitable for flowthrough production process. The lower price of the chemical deposition processes is especially important when the method is related to large-scale glazing applications. Conclusions are derived about which processes are recently considered as most prospective, related to electrochromic materials and devices manufacturing. (paper)

Facile synthesis and electron transport properties of NiO nanostructures investigated by scanning tunneling microscopy

Directory of Open Access Journals (Sweden)

Govind Mallick

2017-08-01

Full Text Available Due to their unique chemical, thermal, electronic and photonic properties, low -dimensional transition metal oxides, especially NiO, have attracted great deal of attention for potential applications in a wide range of technologies, such as, sensors, electrochromic coatings and self-healing materials. However, their synthesis involves multi-step complex procedures that in addition to being expensive, further introduce impurities. Here we present a low cost facile approach to synthesize uniform size NiO nanoparticles (NPs from hydrothermally grown Ni(OH2. Detailed transmission electron microscopic analysis reveal the average size of NiO NPs to be around 29 nm. The dimension of NiO NP is also corroborated by the small area scanning tunneling microscope (STM measurements. Further, we investigate electron transport characteristics of newly synthesized Ni(OH2 and NiO nanoparticles on p-type Si substrate using scanning tunneling microscopy. The conductivity of Ni(OH2 and NiO are determined to be 1.46x10-3 S/cm and 2.37x10-5 S/cm, respectively. The NiO NPs exhibit a lower voltage window (∼0.7 V electron tunneling than the parent Ni(OH2.

Preparation and characterization of VOx nanorods using pulsed laser deposition technique

International Nuclear Information System (INIS)

Rama, N.; Senthil Kumar, E.; Ramachandra Rao, M.S.

2009-01-01

Full text: Vanadium oxide (VO x ) is one of the most functional oxides of the transition metal oxide family. This versatility comes because of the ability of Vanadium to exist as both monovalent and multivalent in these oxides. These oxides find potential usage in the field of thermochromism electrochromism catalysts, electrochemistry etc. especially in their nano-form because of their increased sensitivity to these applications. These nano-forms are usually prepared using conventional techniques such as solgel techniques, vapour phase transport, hydrothermal synthesis etc. In this work we have used pulsed laser deposition technique to fabricate vanadium oxide nanorods for the first time. The grown nanorods has a predominant VO 2 phase with a secondary phase of V 3 O 7 . The diameters of the rods were around 300 nm with Raman spectra showing all the group vibrations corresponding to VO x phase. The nanorods exhibited photoluminescence in the visible range due to the presence of oxygen defects. These results, including the mechanism of growth of these nanorods, will be discussed in detail. The existence of multivalence in these rods finds potential applications in electrochemistry while the visible photoluminescence in optical applications

Mesoporous silicon oxide films and their uses as templates in obtaining nanostructured conductive polymers

Science.gov (United States)

Salgado, R.; Arteaga, G. C.; Arias, J. M.

2018-04-01

Obtaining conductive polymers (CPs) for the manufacture of OLEDs, solar cells, electrochromic devices, sensors, etc., has been possible through the use of electrochemical techniques that allow obtaining films of controlled thickness with positive results in different applications. Current trends point towards the manufacture of nanomaterials, and therefore it is necessary to develop methods that allow obtaining CPs with nanostructured morphology. This is possible by using a porous template to allow the growth of the polymeric materials. However, prior and subsequent treatments are required to separate the material from the template so that it can be evaluated in the applications mentioned above. This is why mesoporous silicon oxide films (template) are essential for the synthesis of nanostructured polymers since both the template and the polymer are obtained on the electrode surface, and therefore it is not necessary to separate the material from the template. Thus, the material can be evaluated directly in the applications mentioned above. The dimensions of the resulting nanostructures will depend on the power, time and technique used for electropolymerization as well as the monomer and the surfactant of the mesoporous film.

Photo- and electro-chromism of diarylethene modified ITO electrodes - towards molecular based read-write-erase information storage

NARCIS (Netherlands)

Areephong, J.; Browne, W.R.; Katsonis, N.; Feringa, B.L.

2006-01-01

Molecular memory devices based on dithienylethene switch modified ITO electrodes undergo reversible ring opening/closing both photo- and electro-chemically with non-destructive electrochemical readout.

Coloration and bleaching mechanism of niobium oxide electrochromic thin films; Sanka niobu electromic usumaku no chakushoshoku mechanism

Energy Technology Data Exchange (ETDEWEB)

Yoshimura, K; Miki, T; Tazawa, M; Jin, P; Igarashi, K; Tanemura, S [National Industrial Research Institute of Nagoya, Nagoya (Japan)

1997-11-25

In order to search for the coloration and bleaching mechanism of niobium oxide, considerations were given on optical properties and electron conditions in niobium oxide thin films (glass plates as substrates coated with ITO) prepared by using the reactive DC magnetron sputtering process. The films were so grown that their thickness will all be 100 nm to facilitate data comparison. Coloration and bleaching of the grown test films were conducted by cyclic voltammetry. Electron spectra were measured by using XPS, and electron energy was analyzed. Coloration of niobium oxide occurs as a result of change in valency electron state from an Nb {sup 5+} state to an Nb {sup 4+} state, while change in the XPS spectra also corresponds with the above change. However, the XPS spectra differ greatly between crystalline samples and amorphous samples. The coloration and bleaching mechanism of the crystallized Nb2O5 film can be explained by a reaction formula similar to that for WO3. However, with regard to the amorphous Nb2O5 film, an independent reaction involving water in the film seems to occur together with the same reaction as in the crystallized film. 9 refs., 5 figs.

Soluble Electrochromic Polymers Incorporating Benzoselenadiazole and Electron Donor Units (Carbazole or Fluorene: Synthesis and Electronic-Optical Properties

Directory of Open Access Journals (Sweden)

Jianzhong Xu

2018-04-01

Full Text Available A series of π-conjugated polymers containing alternating benzoselenadiazole (BSe-bi(thiophene derivative-carbazole or benzoththiadiazole (BSe-bi(thiophene derivative-fluorene units were designed and synthesized. Thiophene derivatives, namely 3-hexylthiophene, 3,4-bihexyloxythiophene, and 3,4-bioctyloxythiophene, were used as the π-bridges of the polymers. The polymers were characterized in detail in terms of their thermal stabilities, cyclic voltammograms, UV-Vis absorption, spectroelectrochemistry, dynamic switching property and so forth. The alkoxy thiophene π-bridged polymers have lower onset oxidation potentials and bandgaps than that of their corresponding alkyl thiophene π-bridged polymers. The selection of the donor units between the carbazole and the fluorene units has nearly no effect on the bandgaps and colors as well as the onset oxidation potentials of the polymers. The increase in the length of the side alkyl chains on the thiophene ring caused a slight increase in the polymer bandgap, which may be caused by the space hindrance effect. The dynamic switching abilities of the polymers were obtained by the chronoabsorptometry method, and the results also suggested that the alkoxy thiophene-containing polymers (as π-bridges have higher contrast ratios than the corresponding alkyl thiophene-containing polymers. Furthermore, the increase in the length of the side alkyl chain might have a detrimental effect on the optical contrast ratios of the polymers.

Position and Orientation Control of a Photo- and Electrochromic Dithienylethene Using a Tripodal Anchor on Gold Surfaces

NARCIS (Netherlands)

Pijper, Thomas C.; Ivashenko, Oleksii; Walko, Martin; Rudolf, Petra; Browne, Wesley R.; Feringa, Ben L.

2015-01-01

A tripodal system for anchoring photochromic dithienylethenes on gold surfaces is reported. The self-assembled monolayers of a tripod-functionalized dithienylethene were characterized by cyclic voltammetry, surface-enhanced Raman spectroscopy (SERS), and X-ray photoelectron spectroscopy (XPS). These

Photo- and Electrochromic Properties of Activated Reactive Evaporated MoO3 Thin Films Grown on Flexible Substrates

Directory of Open Access Journals (Sweden)

K. Hari Krishna

2008-01-01

Full Text Available The molybdenum trioxide (MoO3 thin films were grown onto ITO-coated flexible Kapton substrates using plasma assisted activated reactive evaporation technique. The film depositions were carried out at constant glow power and oxygen partial pressures of 8 W and 1×10−3 Torr, respectively. The influence of substrate temperature on the microstructural and optical properties was investigated. The MoO3 thin films prepared at a substrate temperature of 523 K were found to be composed of uniformly distributed nanosized grains with an orthorhombic structure of α-MoO3. These nanocrystalline MoO3 thin films exhibited higher optical transmittance of about 80% in the visible region with an evaluated optical band gap of 3.29 eV. With the insertion of 12.5 mC/cm2, the films exhibited an optical modulation of 40% in the visible region with coloration efficiency of 22 cm2/C at the wavelength of 550 nm. The MoO3 films deposited at 523 K demonstrated better photochromic properties and showed highest color center concentration for the irradiation time of 30 minutes at 100 mW/cm2.

Recent Advances in Fast Ion Conducting Materials and Devices - Proceedings of the 2nd Asian Conference on Solid State Ionics

Science.gov (United States)

Chowdari, B. V. R.; Liu, Qingguo; Chen, Liquan

The Table of Contents for the book is as follows: * Preface * Invited Papers * Recent Trends in Solid State Ionics * Theoretical Aspects of Fast Ion Conduction in Solids * Chemical Bonding and Intercalation Processes in Framework Structures * Extra-Large Near-Electrode Regions and Diffusion Length on the Solid Electrolyte-Electrode Interface as Studied by Photo-EMF Method * Frequency Response of Glasses * XPS Studies on Ion Conducting Glasses * Characterization of New Ambient Temperature Lithium Polymer-Electrolyte * Recent Development of Polymer Electrolytes: Solid State Voltammetry in Polymer Electrolytes * Secondary Solid State Batteries: From Material Properties to Commercial Development * Silver Vanadium Oxide Bronze and its Applications for Electrochemical Devices * Study on β''-Alumina Solid Electrolyte and β Battery in SIC * Materials for Solid Oxide Fuel Cells * Processing for Super Superionic Ceramics * Hydrogen Production Using Oxide Ionic or Protonic Conductor * Ionically Conductive Sulfide-Based Lithium Glasses * Relation of Conductivity to Structure and Structural Relaxation in Ion-Conducting Glasses * The Mechanism of Ionic Conductivity in Glass * The Role of Synthesis and Structure in Solid State Ionics - Electrodes to Superconductors * Electrochromism in Spin-Coated Thin Films from Peroxo-Poly tungstate Solutions * Electrochemical Studies on High Tc Superconductors * Multivalence Fast Ionic Conductors - Montmorillonites * Contributed Papers * Volt-Ampere Characteristics and Interface Charge Transport in Solid Electrolytes * Internal Friction of Silver Chalcogenides * Thermal Expansion of Ionic and Superionic Solids * Improvement of PEO-LiCF3SO3 Complex Electrolytes Using Additives * Ionic Conductivity of Modified Poly (Methoxy Polyethylene Glycol Methacrylate) s-Lithium Salt Complexes * Solid Polymer Electrolytes of Crosslinked Polyethylene Glycol and Lithium Salts * Single Ionic Conductors Prepared by in Situ Polymerization of Methacrylic Acid

Tunable Broadband Nanocarbon Transparent Conductor by Electrochemical Intercalation.

Science.gov (United States)

Wan, Jiayu; Xu, Yue; Ozdemir, Burak; Xu, Lisha; Sushkov, Andrei B; Yang, Zhi; Yang, Bao; Drew, Dennis; Barone, Veronica; Hu, Liangbing

2017-01-24

Optical transparent and electrical conducting materials with broadband transmission are important for many applications in optoelectronic, telecommunications, and military devices. However, studies of broadband transparent conductors and their controlled modulation are scarce. In this study, we report that reversible transmittance modulation has been achieved with sandwiched nanocarbon thin films (containing carbon nanotubes (CNTs) and reduced graphene oxide (rGO)) via electrochemical alkali-ion intercalation/deintercalation. The transmittance modulation covers a broad range from the visible (450 nm) to the infrared (5 μm), which can be achieved only by rGO rather than pristine graphene films. The large broadband transmittance modulation is understood with DFT calculations, which suggest a decrease in interband transitions in the visible range as well as a reduced reflection in the IR range upon intercalation. We find that a larger interlayer distance in few-layer rGO results in a significant increase in transparency in the infrared region of the spectrum, in agreement with experimental results. Furthermore, a reduced plasma frequency in rGO compared to few-layer graphene is also important to understand the experimental results for broadband transparency in rGO. The broadband transmittance modulation of the CNT/rGO/CNT systems can potentially lead to electrochromic and thermal camouflage applications.

Ion conduction in crystalline superionic solids and its applications

Science.gov (United States)

Chandra, Angesh

2014-06-01

Superionic solids an area of multidisciplinary research activity, incorporates to study the physical, chemical and technological aspects of rapid ion movements within the bulk of the special class of ionic materials. It is an emerging area of materials science, as these solids show tremendous technological scopes to develop wide variety of solid state electrochemical devices such as batteries, fuel cells, supercapacitors, sensors, electrochromic displays (ECDs), memories, etc. These devices have wide range of applicabilities viz. power sources for IC microchips to transport vehicles, novel sensors for controlling atmospheric pollution, new kind of memories for computers, smart windows/display panels, etc. The field grew with a rapid pace since then, especially with regards to designing new materials as well as to explore their device potentialities. Amongst the known superionic solids, fast Ag+ ion conducting crystalline solid electrolytes are attracted special attention due to their relatively higher room temperature conductivity as well as ease of materials handling/synthesis. Ion conduction in these electrolytes is very much interesting part of today. In the present review article, the ion conducting phenomenon and some device applications of crystalline/polycrystalline superionic solid electrolytes have been reviewed in brief. Synthesis and characterization tools have also been discussed in the present review article.

Charge doping and large lattice expansion in oxygen-deficient heteroepitaxial WO3

Science.gov (United States)

Mattoni, Giordano; Filippetti, Alessio; Manca, Nicola; Zubko, Pavlo; Caviglia, Andrea D.

2018-05-01

Tungsten trioxide (WO3) is a versatile material with widespread applications ranging from electrochromics and optoelectronics to water splitting and catalysis of chemical reactions. For technological applications, thin films of WO3 are particularly appealing, taking advantage from a high surface-to-volume ratio and tunable physical properties. However, the growth of stoichiometric crystalline thin films is challenging because the deposition conditions are very sensitive to the formation of oxygen vacancies. In this paper, we show how background oxygen pressure during pulsed laser deposition can be used to tune the structural and electronic properties of WO3 thin films. By performing x-ray diffraction and low-temperature electrical transport measurements, we find changes in the WO3 lattice volume of up to 10% concomitantly with a resistivity drop of more than five orders of magnitude at room temperature as a function of increased oxygen deficiency. We use advanced ab initio calculations to describe in detail the properties of the oxygen vacancy defect states and their evolution in terms of excess charge concentration. Our results depict an intriguing scenario where structural, electronic, optical, and transport properties of WO3 single-crystal thin films can all be purposely tuned by controlling the oxygen vacancy formation during growth.

Method of fabricating electrodes including high-capacity, binder-free anodes for lithium-ion batteries

Science.gov (United States)

Ban, Chunmei; Wu, Zhuangchun; Dillon, Anne C.

2017-01-10

An electrode (110) is provided that may be used in an electrochemical device (100) such as an energy storage/discharge device, e.g., a lithium-ion battery, or an electrochromic device, e.g., a smart window. Hydrothermal techniques and vacuum filtration methods were applied to fabricate the electrode (110). The electrode (110) includes an active portion (140) that is made up of electrochemically active nanoparticles, with one embodiment utilizing 3d-transition metal oxides to provide the electrochemical capacity of the electrode (110). The active material (140) may include other electrochemical materials, such as silicon, tin, lithium manganese oxide, and lithium iron phosphate. The electrode (110) also includes a matrix or net (170) of electrically conductive nanomaterial that acts to connect and/or bind the active nanoparticles (140) such that no binder material is required in the electrode (110), which allows more active materials (140) to be included to improve energy density and other desirable characteristics of the electrode. The matrix material (170) may take the form of carbon nanotubes, such as single-wall, double-wall, and/or multi-wall nanotubes, and be provided as about 2 to 30 percent weight of the electrode (110) with the rest being the active material (140).

Hybrid metal grid-polymer-carbon nanotube electrodes for high luminance organic light emitting diodes

International Nuclear Information System (INIS)

Sam, F Laurent M; Dabera, G Dinesha M R; Lai, Khue T; Mills, Christopher A; Rozanski, Lynn J; Silva, S Ravi P

2014-01-01

Organic light emitting diodes (OLEDs) incorporating grid transparent conducting electrodes (TCEs) with wide grid line spacing suffer from an inability to transfer charge carriers across the gaps in the grids to promote light emission in these areas. High luminance OLEDs fabricated using a hybrid TCE composed of poly(3,4-ethylenedioxythiophene) poly(styrenesulfonate) (PEDOT:PSS PH1000) or regioregular poly(3-hexylthiophene)-wrapped semiconducting single-walled carbon nanotubes (rrP3HT-SWCNT) in combination with a nanometre thin gold grid are reported here. OLEDs fabricated using the hybrid gold grid/PH1000 TCE have a luminance of 18 000 cd m −2 at 9 V; the same as the reference indium tin oxide (ITO) OLED. The gold grid/rrP3HT-SWCNT OLEDs have a lower luminance of 8260 cd m −2 at 9 V, which is likely due to a rougher rrP3HT-SWCNT surface. These results demonstrate that the hybrid gold grid/PH1000 TCE is a promising replacement for ITO in future plastic electronics applications including OLEDs and organic photovoltaics. For applications where surface roughness is not critical, e.g. electrochromic devices or discharge of static electricity, the gold grid/rrP3HT-SWCNT hybrid TCE can be employed. (paper)

Recent Developments in p-Type Oxide Semiconductor Materials and Devices

KAUST Repository

Wang, Zhenwei

2016-02-16

The development of transparent p-type oxide semiconductors with good performance may be a true enabler for a variety of applications where transparency, power efficiency, and greater circuit complexity are needed. Such applications include transparent electronics, displays, sensors, photovoltaics, memristors, and electrochromics. Hence, here, recent developments in materials and devices based on p-type oxide semiconductors are reviewed, including ternary Cu-bearing oxides, binary copper oxides, tin monoxide, spinel oxides, and nickel oxides. The crystal and electronic structures of these materials are discussed, along with approaches to enhance valence-band dispersion to reduce effective mass and increase mobility. Strategies to reduce interfacial defects, off-state current, and material instability are suggested. Furthermore, it is shown that promising progress has been made in the performance of various types of devices based on p-type oxides. Several innovative approaches exist to fabricate transparent complementary metal oxide semiconductor (CMOS) devices, including novel device fabrication schemes and utilization of surface chemistry effects, resulting in good inverter gains. However, despite recent developments, p-type oxides still lag in performance behind their n-type counterparts, which have entered volume production in the display market. Recent successes along with the hurdles that stand in the way of commercial success of p-type oxide semiconductors are presented.

Recent Developments in p-Type Oxide Semiconductor Materials and Devices

KAUST Repository

Wang, Zhenwei; Nayak, Pradipta K.; Caraveo-Frescas, Jesus Alfonso; Alshareef, Husam N.

2016-01-01

The development of transparent p-type oxide semiconductors with good performance may be a true enabler for a variety of applications where transparency, power efficiency, and greater circuit complexity are needed. Such applications include transparent electronics, displays, sensors, photovoltaics, memristors, and electrochromics. Hence, here, recent developments in materials and devices based on p-type oxide semiconductors are reviewed, including ternary Cu-bearing oxides, binary copper oxides, tin monoxide, spinel oxides, and nickel oxides. The crystal and electronic structures of these materials are discussed, along with approaches to enhance valence-band dispersion to reduce effective mass and increase mobility. Strategies to reduce interfacial defects, off-state current, and material instability are suggested. Furthermore, it is shown that promising progress has been made in the performance of various types of devices based on p-type oxides. Several innovative approaches exist to fabricate transparent complementary metal oxide semiconductor (CMOS) devices, including novel device fabrication schemes and utilization of surface chemistry effects, resulting in good inverter gains. However, despite recent developments, p-type oxides still lag in performance behind their n-type counterparts, which have entered volume production in the display market. Recent successes along with the hurdles that stand in the way of commercial success of p-type oxide semiconductors are presented.

Preparation of Supercapacitors on Flexible Substrates with Electrodeposited PEDOT/Graphene Composites.

Science.gov (United States)

Lehtimäki, Suvi; Suominen, Milla; Damlin, Pia; Tuukkanen, Sampo; Kvarnström, Carita; Lupo, Donald

2015-10-14

Composite films consisting of poly(3,4-ethylenedioxythiophene) (PEDOT) and graphene oxide (GO) were electrochemically polymerized by electrooxidation of EDOT in ionic liquid (BMIMBF4) onto flexible electrode substrates. Two polymerization approaches were compared, and the cyclic voltammetry (CV) method was found to be superior to potentiostatic polymerization for the growth of PEDOT/GO films. After deposition, incorporated GO was reduced to rGO by a rapid electrochemical method of repetitive cathodic potential cycling, without using any reducing reagents. The films were characterized in 3-electrode configuration in BMIMBF4. Symmetric supercapacitors with aqueous electrolyte were assembled from the composite films and characterized through cyclic voltammetry and galvanostatic discharge tests. It was shown that PEDOT/rGO composites have better capacitive properties than pure PEDOT or the unreduced composite film. The cycling stability of the supercapacitors was also tested, and the results indicate that the specific capacitance still retains well over 90% of the initial value after 2000 consecutive charging/discharging cycles. The supercapacitors were demonstrated as energy storages in a room light energy harvester with a printed organic solar cell and printed electrochromic display. The results are promising for the development of energy-autonomous, low-power, and disposable electronics.

Cathodic electrodeposition of mixed molybdenum tungsten oxides from peroxo-polymolybdotungstate solutions.

Science.gov (United States)

Kondrachova, Lilia; Hahn, Benjamin P; Vijayaraghavan, Ganesh; Williams, Ryan D; Stevenson, Keith J

2006-12-05

Mixed molybdenum tungsten trioxide films of varying stoichiometry (MoxW1 - xO3, 0 cathodic electrodeposition on indium tin oxide (ITO)-coated glass substrates from aqueous peroxo-polymolybdotungstate solutions. Electrochemical quartz crystal microbalance (EQCM), cyclic voltammetry, and chronocoulometry were used to gain insight into the electrodeposition mechanism. The compositional and structural properties were characterized for MoxW1 - xO3 films deposited at intermediate potentials (-0.35 V vs Ag/AgCl) and sintered at 250 degrees C using energy-dispersive spectroscopy, X-ray diffraction, and Raman spectroscopy. These studies reveal that films consist of homogeneously mixed MoxW1 - xO3, with an enriched Mo content ranging in composition from 0.4 < x < 0.7 depending upon the mol % Mo present in the deposition solution. Chronoamperometry and spectroelectrochemical measurements were conducted to estimate lithium ion diffusion coefficients and coloration efficiencies for the mixed metal oxide films in 1 M LiClO4/propylene carbonate. The subtle interplay between structural and compositional properties due to the uniform mixing of Mo and W oxide components shows that electrochromic and lithium ion transport properties are moderately enhanced relative to those of single-component WO3 and MoO3 and demonstrate improved structural stability over pure MoO3 polymorphs during electrochemical cycling.

Ionic Liquid Mediated Dispersion and Support of Functional Molecules on Cellulose Fibers for Stimuli-Responsive Chromic Paper Devices.

Science.gov (United States)

Koga, Hirotaka; Nogi, Masaya; Isogai, Akira

2017-11-22

Functional molecules play a significant role in the development of high-performance composite materials. Functional molecules should be well dispersed (ideally dissolved) and supported within an easy-to-handle substrate to take full advantage of their functionality and ensure easy handling. However, simultaneously achieving the dissolution and support of functional molecules remains a challenge. Herein, we propose the combination of a nonvolatile ionic liquid and an easy-to-handle cellulose paper substrate for achieving this goal. First, the photochromic molecule, i.e., diarylethene, was dissolved in the ionic liquid 1-butyl-3-methylimidazolium bis(trifluoromethanesulfonyl)imide ([bmim]NTf 2 ). Then, diarylethene/[bmim]NTf 2 was supported on cellulose fibers within the paper, through hydrogen bonding between [bmim] cations of the ionic liquid and the abundant hydroxyl groups of cellulose. The as-prepared paper composites exhibited reversible, rapid, uniform, and vivid coloration and bleaching upon ultraviolet and visible light irradiation. The photochromic performance was superior to that of the paper prepared in the absence of [bmim]NTf 2 . This concept could be applied to other functional molecules. For example, lithium perchlorate/[bmim] tetrafluoroborate supported within cellulose paper acted as a flexible electrolyte to provide a paper-based electrochromic device. These findings are expected to further the development of composite materials with high functionality and practicality.

Understanding the conductive channel evolution in Na:WO(3-x)-based planar devices.

Science.gov (United States)

Shang, Dashan; Li, Peining; Wang, Tao; Carria, Egidio; Sun, Jirong; Shen, Baogen; Taubner, Thomas; Valov, Ilia; Waser, Rainer; Wuttig, Matthias

2015-04-14

An ion migration process in a solid electrolyte is important for ion-based functional devices, such as fuel cells, batteries, electrochromics, gas sensors, and resistive switching systems. In this study, a planar sandwich structure is prepared by depositing tungsten oxide (WO(3-x)) films on a soda-lime glass substrate, from which Na(+) diffuses into the WO(3-x) films during the deposition. The entire process of Na(+) migration driven by an alternating electric field is visualized in the Na-doped WO(3-x) films in the form of conductive channel by in situ optical imaging combined with infrared spectroscopy and near-field imaging techniques. A reversible change of geometry between a parabolic and a bar channel is observed with the resistance change of the devices. The peculiar channel evolution is interpreted by a thermal-stress-induced mechanical deformation of the films and an asymmetric Na(+) mobility between the parabolic and the bar channels. These results exemplify a typical ion migration process driven by an alternating electric field in a solid electrolyte with a low ion mobility and are expected to be beneficial to improve the controllability of the ion migration in ion-based functional devices, such as resistive switching devices.

Controlling the mode of operation of organic transistors through side-chain engineering

KAUST Repository

Giovannitti, Alexander

2016-10-11

Electrolyte-gated organic transistors offer low bias operation facilitated by direct contact of the transistor channel with an electrolyte. Their operation mode is generally defined by the dimensionality of charge transport, where a field-effect transistor allows for electrostatic charge accumulation at the electrolyte/semiconductor interface, whereas an organic electrochemical transistor (OECT) facilitates penetration of ions into the bulk of the channel, considered a slow process, leading to volumetric doping and electronic transport. Conducting polymer OECTs allow for fast switching and high currents through incorporation of excess, hygroscopic ionic phases, but operate in depletion mode. Here, we show that the use of glycolated side chains on a thiophene backbone can result in accumulation mode OECTs with high currents, transconductance, and sharp subthreshold switching, while maintaining fast switching speeds. Compared with alkylated analogs of the same backbone, the triethylene glycol side chains shift the mode of operation of aqueous electrolyte-gated transistors from interfacial to bulk doping/transport and show complete and reversible electrochromism and high volumetric capacitance at low operating biases. We propose that the glycol side chains facilitate hydration and ion penetration, without compromising electronic mobility, and suggest that this synthetic approach can be used to guide the design of organic mixed conductors.

Photolithographically Patterned TiO2 Films for Electrolyte-Gated Transistors.

Science.gov (United States)

Valitova, Irina; Kumar, Prajwal; Meng, Xiang; Soavi, Francesca; Santato, Clara; Cicoira, Fabio

2016-06-15

Metal oxides constitute a class of materials whose properties cover the entire range from insulators to semiconductors to metals. Most metal oxides are abundant and accessible at moderate cost. Metal oxides are widely investigated as channel materials in transistors, including electrolyte-gated transistors, where the charge carrier density can be modulated by orders of magnitude upon application of relatively low electrical bias (2 V). Electrolyte gating offers the opportunity to envisage new applications in flexible and printed electronics as well as to improve our current understanding of fundamental processes in electronic materials, e.g. insulator/metal transitions. In this work, we employ photolithographically patterned TiO2 films as channels for electrolyte-gated transistors. TiO2 stands out for its biocompatibility and wide use in sensing, electrochromics, photovoltaics and photocatalysis. We fabricated TiO2 electrolyte-gated transistors using an original unconventional parylene-based patterning technique. By using a combination of electrochemical and charge carrier transport measurements we demonstrated that patterning improves the performance of electrolyte-gated TiO2 transistors with respect to their unpatterned counterparts. Patterned electrolyte-gated (EG) TiO2 transistors show threshold voltages of about 0.9 V, ON/OFF ratios as high as 1 × 10(5), and electron mobility above 1 cm(2)/(V s).

Controlling the mode of operation of organic transistors through side-chain engineering

Science.gov (United States)

Giovannitti, Alexander; Sbircea, Dan-Tiberiu; Inal, Sahika; Nielsen, Christian B.; Bandiello, Enrico; Hanifi, David A.; Sessolo, Michele; Malliaras, George G.; McCulloch, Iain; Rivnay, Jonathan

2016-01-01

Electrolyte-gated organic transistors offer low bias operation facilitated by direct contact of the transistor channel with an electrolyte. Their operation mode is generally defined by the dimensionality of charge transport, where a field-effect transistor allows for electrostatic charge accumulation at the electrolyte/semiconductor interface, whereas an organic electrochemical transistor (OECT) facilitates penetration of ions into the bulk of the channel, considered a slow process, leading to volumetric doping and electronic transport. Conducting polymer OECTs allow for fast switching and high currents through incorporation of excess, hygroscopic ionic phases, but operate in depletion mode. Here, we show that the use of glycolated side chains on a thiophene backbone can result in accumulation mode OECTs with high currents, transconductance, and sharp subthreshold switching, while maintaining fast switching speeds. Compared with alkylated analogs of the same backbone, the triethylene glycol side chains shift the mode of operation of aqueous electrolyte-gated transistors from interfacial to bulk doping/transport and show complete and reversible electrochromism and high volumetric capacitance at low operating biases. We propose that the glycol side chains facilitate hydration and ion penetration, without compromising electronic mobility, and suggest that this synthetic approach can be used to guide the design of organic mixed conductors. PMID:27790983

Electrochemical and optical properties of new soluble dithienylpyrroles based on azo dyes

International Nuclear Information System (INIS)

Cihaner, Atilla; Algi, Fatih

2009-01-01

Two dithienylpyrroles based on azo dyes, namely 2,5'-dimethyl-[4-(2,5-di-thiophen-2-yl-pyrrol-1-yl)-phenyl]azobenzene (SNS-AB2) and 2,5'-dimethyloxy-[4-(2,5-di-thiophen-2-yl-pyrrol-1-yl)-phenyl]azobenzene (SNS-AB3), were synthesized and their corresponding polymers (PSNS-AB2 and PSNS-AB3) were successfully obtained via electropolymerization. The monomers have lower oxidation potentials (0.75 V and 0.80 V vs. Ag/AgCl for SNS-AB2 and SNS-AB3, respectively) when compared to their analogous. Both monomers exhibited photoisomerism properties under irradiation at 360 nm. During the irradiation process, for example, the color of SNS-AB3 changes from yellow to greenish yellow. The electroactive polymer films have well defined and reversible redox couples with a good cycle stability in both aqueous and organic solutions. The polymer films also exhibited electrochromic behaviors; color changes from yellowish green to dark green for the PSNS-AB2 (λ max = 435 nm and E g = 2.31 eV) and from mustard color to green for PSNS-AB3 (λ max = 430 nm and E g = 2.34 eV). Furthermore, the soluble polymers demonstrated different hues of yellow and green colors

Charge transport in metal oxide nanocrystal-based materials

Science.gov (United States)

Runnerstrom, Evan Lars

structure. Charge transport can obviously be taken to mean the conduction of electrons, but it also refers to the motion of ions, such as lithium ions and protons. In many cases, the transport of ions is married to the motion of electrons as well, either through an external electrical circuit, or within the same material in the case of mixed ionic electronic conductors. The collective motion of electrons over short length scales, that is, within single nanocrystals, is also a subject of study as it pertains to plasmonic nanocrystals. Finally, charge transport can also be coupled to or result from the formation of defects in metal oxides. All of these modes of charge transport in metal oxides gain further complexity when considered in nanocrystalline systems, where the introduction of numerous surfaces can change the character of charge transport relative to bulk systems, providing opportunities to exploit new physical phenomena. Part I of this dissertation explores the combination of electronic and ionic transport in electrochromic devices based on nanocrystals. Colloidal chemistry and solution processing are used to fabricate nanocomposites based on electrochromic tin-doped indium oxide (ITO) nanocrystals. The nanocomposites, which are completely synthesized using solution processing, consist of ITO nanocrystals and lithium bis(trifluoromethylsulfonyl)amide (LiTFSI) salt dispersed in a lithium ion-conducting polymer matrix of either poly(ethylene oxide) (PEO) or poly(methyl methacrylate) (PMMA). ITO nanocrystals are prepared by colloidal synthetic methods and the nanocrystal surface chemistry is modified to achieve favorable nanocrystal-polymer interactions. Homogeneous solutions containing polymer, ITO nanocrystals, and lithium salt are thus prepared and deposited by spin casting. Characterization by DC electronic measurements, microscopy, and x-ray scattering techniques show that the ITO nanocrystals form a complete, connected electrode within a polymer electrolyte

Electrochromic and electrochemical capacitive properties of tungsten oxide and its polyaniline nanocomposite films obtained by chemical bath deposition method

CSIR Research Space (South Africa)

Nwanya, AC

2014-05-01

Full Text Available Polyanine and its nanocomposite WO3/PANI films were deposited on fluorine doped tin oxide (FTO) glassslides by simple chemical bath deposition method. The morphology structure of the composite film wasstudied using atomic force microscopy (AFM...

Analogy for the maximum obtainable colouration between electrochromic, gasochromic, and electrocolouration in DC-sputtered thin WO3-y films

International Nuclear Information System (INIS)

Stolze, M.; Gogova, D.; Thomas, L.-K.

2005-01-01

Tungsten oxide films with varied substoichiometry were deposited by reactive DC-sputtering from a W target at different oxygen partial pressures. The inherent maximum achievable electrochemical colouration and electrocolouration were found to be dependent on the oxygen content and consequently on the film substoichiometry. These results were related to those obtained in a previous study by colouration with hydrogen spillover from a catalyst (gasochromic colouration) of films fabricated in the same way. A clear analogy among the colouration by the three different techniques appeared

A Tetrahydrofuran-selective Optical Solvent Sensor Based on Solvatochromic Polydiacetylene

International Nuclear Information System (INIS)

Park, Dong-Hoon; Kim, Bubsung; Kim, Jong-Man

2016-01-01

Polydiacetylene (PDAs) have received great attention as colorimetric sensors since these conjugated polymers undergo a blue-to-red color change upon various chemical/biochemical and physical stimuli. PDAs have been reported to display thermochromism (heat), solvatochromism (solvent), mechanochromism (mechanical strain) as well as magnetochromism (magnetic force) electrochromism (electric current), and affinochromism (ligand-receptor interaction). The solvent induced color change of PDA is generally non-specific and irreversible. For instance, the PDA derived from 10,12-pentacosadiynoic acid (PCDA) undergoes a blue-to-red (or purple) color change upon exposure to many common organic solvents including tetrahydrofuran (THF), chloroform, dichloromethane, acetone, methanol (MeOH), ethyl acetate (EA), and diethyl ether. The results obtained from Raman spectral analysis suggests that exposure to THF causes the distortion of the backbone of the polymer main chain and some conformational changes in the aliphatic side chain. Solvatochromism of a PDA is closely related to the solubility of a diacetylene monomer. PDA undergoes a color change when the dissolution of unpolymerized monomers causes some void in the PDA supramolecules. Since PCDA-mBzA has a good solubility only in THF, colorimetric transition of PDA occurs only in response to THF. Since solubility of a diacetylene monomer can be manipulated by structural change of the monomer, we believe the strategy described in current investigation should be useful for the development of solvent-specific PDA sensor systems

Realization and characterization of a cellulose and conducting polymer-based ultrathin films composite material

International Nuclear Information System (INIS)

Henry, Christelle

1998-01-01

This work was dedicated to the realization and the characterization of an organic composite material in order to obtain organized ultrathin films with high conductivity and good mechanical properties. In this purpose, the Langmuir-Blodgett (LB) film of a crosslinked alkyl cellulose (rigid-rod polymer) was used as a host matrix for the electro-polymerization of alkyl thiophene and pyrrole. The first interesting result was the synthesis of a bigger amount of conducting alkyl polymer in the presence of cellulose. With the help of a photo-patterning technique, we were able to form contacts more or less conducting on the substrate. We have also shown that the conducting polymer grows beyond the electrode area until distances never described up to now in the literature. A preferential orientation of the conducting polymer chains along the LB dipping direction of the cellulose has been observed in some cases. Even for the films without molecular orientation, we have systematically observed a microscopic or macroscopic anisotropy. This phenomenon appears as domains concentrated in conducting polymers with anisotropic shapes oriented along the dipping direction. Finally, we have noticed that cellulose doesn't change the conductivity and the electrochromic properties of the conducting polymer. Beyond the keeping of these intrinsic properties, the matrix allows to stabilize the film when it is in contact with an organic solvent. (author) [fr

Spectroscopic, electrochemical and photovoltaic properties of Pt(ii) and Pd(ii) complexes of a chelating 1,10-phenanthroline appended perylene diimide.

Science.gov (United States)

Işık Büyükekşi, Sebile; Şengül, Abdurrahman; Erdönmez, Seda; Altındal, Ahmet; Orman, Efe Baturhan; Özkaya, Ali Rıza

2018-02-20

In this study, a bis-chelating bridging perylene diimide ditopic ligand, namely N,N'-di(1,10-phenanthroline)-1,6,7,12-tetrakis-(4-methoxyphenoxy)perylene tetracarboxylic acid diimide (1), was synthesized and characterized. Further reactions of 1 with d 8 metal ions such as Pt(ii) and Pd(ii) having preferential square-planar geometry afforded the novel triads [(Cl 2 )M(ii)-(1)-M(ii)(Cl 2 )] where M(ii) = Pt(ii) (2), and Pd(ii) (3), respectively. The isolated triads and the key precursor were fully characterized by FT-IR, 1D-NMR ( 1 H NMR and 13 C DEPT NMR), 2D-NMR ( 1 H- 1 H COSY, 1 H- 13 C HSQC, 1 H- 13 C HMBC), MALDI-TOF mass and UV/Vis spectroscopy. The electrochemical properties of 1, 2 and 3 were investigated by cyclic voltammetry as well as in situ spectroelectrochemistry and also in situ electrocolorimetric measurements. These compounds were shown to exhibit net colour changes suitable for electrochromic applications. The compounds exhibited remarkably narrow HOMO-LUMO gaps, leading to their ease of reduction at low negative potentials. More importantly, dye-sensitized solar cells (DSSCs) were also fabricated using 1-3 to clarify the potential use of these complexes as a sensitizer. Analysis of the experimental data indicated that 2 has good potential as a sensitizer material for DSSCs.

Redox behavior and optical response of nanostructured poly(3,4-ethylenedioxythiophene) films grown in a camphorsulfonic acid based micellar solution

International Nuclear Information System (INIS)

Bhandari, Shweta; Deepa, M.; Singh, S.; Gupta, Govind; Kant, Rama

2008-01-01

Poly(3,4-ethylenedioxythiophene) (PEDOT) films have been electropolymerized from an aqueous micellar solution comprising camphorsulfonic acid (CSA), lithium trifluoromethanesulfonate (LiCF 3 SO 3 ) and EDOT. The inclusion of the dopants CS - and CF 3 SO 3 - in the polymer structure and an unusually high doping level of 0.54 have been ascertained by the X-ray photoelectron spectroscopy. Transmission electron microscopy and atomic force microscopy studies show that the micellar effect of CSA leads to a morphology wherein polymer particles link together to form elongated shapes and also endows the film with a surface roughness of 25-30 nm. These nanostructures permit a facile intercalation-deintercalation of anions in the film during redox cycling. Electrochemical impedance spectroscopy show that the charge transfer phenomenon at the PEDOT-electrolyte interface is dominant in the high frequency region and diffusion controlled ionic movement prevails in the low frequency regime. The use of these films as potential cathodes in electrochromic windows is rationalized not only on the basis of their high scalability and ease of processing but also due to their large coloration efficiency (123 cm 2 C -1 ) and transmission modulation (50%) at a photopic wavelength of 550 nm. But further improvement in color-bleach kinetics and reproducibility of redox behavior is desirable to broaden their spectrum of utility

Building Applications, Opportunities and Challenges of Active Shading Systems: A State-of-the-Art Review

Directory of Open Access Journals (Sweden)

Joud Al Dakheel

2017-10-01

Full Text Available Active shading systems in buildings have emerged as a high performing shading solution that selectively and optimally controls daylight and heat gains. Active shading systems are increasingly used in buildings, due to their ability to mainly improve the building environment, reduce energy consumption and in some cases generate energy. They may be categorized into three classes: smart glazing, kinetic shading and integrated renewable energy shading. This paper reviews the current status of the different types in terms of design principle and working mechanism of the systems, performance, control strategies and building applications. Challenges, limitations and future opportunities of the systems are then discussed. The review highlights that despite its high initial cost, the electrochromic (EC glazing is the most applied smart glazing due to the extensive use of glass in buildings under all climatic conditions. In terms of external shadings, the rotating shading type is the predominantly used one in buildings due to its low initial cost. Algae façades and folding shading systems are still emerging types, with high initial and maintenance costs and requiring specialist installers. The algae façade systems and PV integrated shading systems are a promising solution due to their dual benefits of providing shading and generating electricity. Active shading systems were found to save 12 to 50% of the building cooling electricity consumption.

A Tetrahydrofuran-selective Optical Solvent Sensor Based on Solvatochromic Polydiacetylene

Energy Technology Data Exchange (ETDEWEB)

Park, Dong-Hoon; Kim, Bubsung; Kim, Jong-Man [Hanyang University, Seoul (Korea, Republic of)

2016-06-15

Polydiacetylene (PDAs) have received great attention as colorimetric sensors since these conjugated polymers undergo a blue-to-red color change upon various chemical/biochemical and physical stimuli. PDAs have been reported to display thermochromism (heat), solvatochromism (solvent), mechanochromism (mechanical strain) as well as magnetochromism (magnetic force) electrochromism (electric current), and affinochromism (ligand-receptor interaction). The solvent induced color change of PDA is generally non-specific and irreversible. For instance, the PDA derived from 10,12-pentacosadiynoic acid (PCDA) undergoes a blue-to-red (or purple) color change upon exposure to many common organic solvents including tetrahydrofuran (THF), chloroform, dichloromethane, acetone, methanol (MeOH), ethyl acetate (EA), and diethyl ether. The results obtained from Raman spectral analysis suggests that exposure to THF causes the distortion of the backbone of the polymer main chain and some conformational changes in the aliphatic side chain. Solvatochromism of a PDA is closely related to the solubility of a diacetylene monomer. PDA undergoes a color change when the dissolution of unpolymerized monomers causes some void in the PDA supramolecules. Since PCDA-mBzA has a good solubility only in THF, colorimetric transition of PDA occurs only in response to THF. Since solubility of a diacetylene monomer can be manipulated by structural change of the monomer, we believe the strategy described in current investigation should be useful for the development of solvent-specific PDA sensor systems.

Characterization of (0.3-x)WO3-0.70Sb2O3-xAgNO3 (0.29 ≥ X ≥ 0.01) polycrystalline system

International Nuclear Information System (INIS)

Ramesh, S.; Das, B.B.; Nagraju, D.

2013-01-01

Polyoxometalates (POMs) form a characteristic class of inorganic metal-oxygen compound. Due to their structural diversity and attractive properties, POMs have been attracted during the last decades. Especially, transition metal substituted POMs have become one of the most fascinating field in the synthetic chemistry. POMs, not only due to their unique properties on size, shape, charge density, redox potential and stability, but also owing to the promising applications in catalysis, medicine and material science. It is well known that tungsten produces many complex oxides similar to molybdenum and it is known to exhibit a variety of interesting properties counting semiconductivity, photochromism and electrochromism, space-charge injection. The structural identification of tungstate would be helpful in determining the species responsible for the properties mentioned. In the tungsten trioxide systems, tungsten exhibit mixed-valence states, specifically W 5+ (5d 1 ) and W 6+ (5d 0 ). The thermal hopping of electrons between these two valence states appears to be responsible for conduction in tungsten containing complex oxides. Since a ternary system such as WO 3 -Sb 2 O 3 AgNO 3 contains different structural units with interesting paramagnetic probe, WO 3 (4d 1 ). The study of structure-property relations as well as site symmetry around the WO 5+ site of such system is indeed interesting. However, the report on EPR studies of such systems is limited

Spectroelectrochemical and electrochromic behaviors of newly synthesized poly[3′-(2-aminopyrimidyl)-2,2′:5′,2″-terthiophene

International Nuclear Information System (INIS)

Kim, Dong-Min; Shim, Kyu-Bin; Son, Jung Ik; Reddy, Sanapalli S.; Shim, Yoon-Bo

2013-01-01

The functionalized conductive polymer precursor of the terthiophene derivative, 3′-(2-aminopyrimidyl)-2,2′:5′,2″-terthiophene (PATT) was firstly synthesized and confirmed with FT-IR, 1 H NMR, 13 C NMR, and mass spectroscopy. The electrochemical and electronic properties of polyPATT film are investigated and compared with that of poly(2,2′:5′,2″-terthiophene-3′-p-benzoic acid) (polyTTBA), which has an electron-accepting group. The cyclic voltammograms (CVs) recorded for electrochemically grown polyPATT reveal the redox peaks at +1.1/+0.96 V, and the conductivity increases monotonically as the applying potential goes to the positive direction (0.11 S cm −1 at +1.4 V). The spectroelectrochemical analysis of polyPATT reveals the absorption bands at 456, 825 and 643 nm corresponding to the π–π* transition, polaron, and bipolaron formations, respectively. The highest occupied molecular orbital (HOMO) and lowest unoccupied molecular orbital (LUMO) energy levels of the polyPATT film bearing an electron donating group are to be 3.60 and 5.54 eV, respectively. The polyPATT film shows reversible multiple color transition within 0.6 s (from brownish-yellow (at 0.0 V) to blue (at +1.4 V)) when the potential switches between the reduced and oxidized states

Novel poly(triphenylamine-alt-fluorene) with asymmetric hexaphenylbenzene and pyrene moieties: synthesis, fluorescence, flexible near-infrared electrochromic devices and theoretical investigation

KAUST Repository

Wang, Po-I.; Shie, Wan-Ru; Jiang, Jyh-Chiang; Li, Lain-Jong; Liaw, Der-Jang

2016-01-01

. The conjugated polymer had a weight-average molecular weight of 5.8 × 104 g mol-1 with a polydispersity index of 2.5 characterized by gel permeation chromatography (GPC). HPBPYFL6 showed good solubility in common organic solvents such as NMP, THF, toluene

Photothermally Activated Pyroelectric Polymer Films for Harvesting of Solar Heat with a Hybrid Energy Cell Structure.

Science.gov (United States)

Park, Teahoon; Na, Jongbeom; Kim, Byeonggwan; Kim, Younghoon; Shin, Haijin; Kim, Eunkyoung

2015-12-22

Photothermal effects in poly(3,4-ethylenedioxythiophene)s (PEDOTs) were explored for pyroelectric conversion. A poled ferroelectric film was coated on both sides with PEDOT via solution casting polymerization of EDOT, to give highly conductive and effective photothermal thin films of PEDOT. The PEDOT films not only provided heat source upon light exposure but worked as electrodes for the output energy from the pyroelectric layer in an energy harvester hybridized with a thermoelectric layer. Compared to a bare thermoelectric system under NIR irradiation, the photothermal-pyro-thermoelectric device showed more than 6 times higher thermoelectric output with the additional pyroelectric output. The photothermally driven pyroelectric harvesting film provided a very fast electric output with a high voltage output (Vout) of 15 V. The pyroelectric effect was significant due to the transparent and high photothermal PEDOT film, which could also work as an electrode. A hybrid energy harvester was assembled to enhance photoconversion efficiency (PCE) of a solar cell with a thermoelectric device operated by the photothermally generated heat. The PCE was increased more than 20% under sunlight irradiation (AM 1.5G) utilizing the transmitted light through the photovoltaic cell as a heat source that was converted into pyroelectric and thermoelectric output simultaneously from the high photothermal PEDOT electrodes. Overall, this work provides a dynamic and static hybrid energy cell to harvest solar energy in full spectral range and thermal energy, to allow solar powered switching of an electrochromic display.

Tungsten oxide thin film exposed to low energy D and He plasma: evidence for a thermal enhancement of the erosion yield

Science.gov (United States)

Hijazi, Hussein; Martin, C.; Roubin, P.; Addab, Y.; Cabie, C.; Pardanaud, C.; Bannister, M.; Meyer, F.

2017-10-01

Nanocrystalline tungsten oxide thin films (25 nm - 250 nm thickness) produced by thermal oxidation of a tungsten substrate were exposed to low energy D and He plasma. Low energy D plasma exposure (11 eV/D+) of these films have resulted in the formation of a tungsten bronze (DxWO3) clearly observed by Raman microscopy. D plasma bombardment (4 1021 m-2) has also induced a color change of the oxide layer which is similar to the well-known electro-chromic effect and has been named ``plasma-chromic effect''. To unravel physical and chemical origins of the modifications observed under exposure, similar tungsten oxide films were also exposed to low energy helium plasma (20 eV/He+) . Due to the low fluence (4 1021 m-2) and low ion energy (20 eV), at room temperature, He exposure has induced only very few morphological and structural modifications. On the contrary, at 673 K, significant erosion is observed, which gives evidence for an unexpected thermal enhancement of the erosion yield. We present here new results concerning He beam exposures at low fluence (4 1021 m-2) varying the He+ energy from 20 eV to 320 eV to measure the tungsten oxide sputtering threshold energy. Detailed analyses before/after exposure to describe the D and He interaction with the oxide layer, its erosion and structural modification at the atomic and micrometer scale will be presented.

Energy in buildings: Efficiency, renewables and storage

Science.gov (United States)

Koebel, Matthias M.

2017-07-01

This lecture summary provides a short but comprehensive overview on the "energy and buildings" topic. Buildings account for roughly 40% of the global energy demands. Thus, an increased adoption of existing and upcoming materials and solutions for the building sector represents an enormous potential to reduce building related energy demands and greenhouse gas emissions. The central question is how the building envelope (insulation, fenestration, construction style, solar control) affects building energy demands. Compared to conventional insulation materials, superinsulation materials such as vacuum insulation panels and silica aerogel achieve the same thermal performance with significantly thinner insulation layers. With low-emissivity coatings and appropriate filler gasses, double and triple glazing reduce thermal losses by up to an order of magnitude compared to old single pane windows, while vacuum insulation and aerogel filled glazing could reduce these even further. Electrochromic and other switchable glazing solutions maximize solar gains during wintertime and minimize illumination demands whilst avoiding overheating in summer. Upon integration of renewable energy systems into the building energy supply, buildings can become both producers and consumers of energy. Combined with dynamic user behavior, temporal variations in the production of renewable energy require appropriate storage solutions, both thermal and electrical, and the integration of buildings into smart grids and energy district networks. The combination of these measures allows a reduction of the existing building stock by roughly a factor of three —a promising, but cost intensive way, to prepare our buildings for the energy turnaround.

Active coatings technologies for tailorable military coating systems

Science.gov (United States)

Zunino, J. L., III

2007-04-01

The main objective of the U.S. Army's Active Coatings Technologies Program is to develop technologies that can be used in combination to tailor coatings for utilization on Army Materiel. The Active Coatings Technologies Program, ACT, is divided into several thrusts, including the Smart Coatings Materiel Program, Munitions Coatings Technologies, Active Sensor packages, Systems Health Monitoring, Novel Technology Development, as well as other advanced technologies. The goal of the ACT Program is to conduct research leading to the development of multiple coatings systems for use on various military platforms, incorporating unique properties such as self repair, selective removal, corrosion resistance, sensing, ability to modify coatings' physical properties, colorizing, and alerting logistics staff when tanks or weaponry require more extensive repair. A partnership between the U.S. Army Corrosion Office at Picatinny Arsenal, NJ along with researchers at the New Jersey Institute of Technology, NJ, Clemson University, SC, University of New Hampshire, NH, and University of Massachusetts (Lowell), MA, are developing the next generation of Smart Coatings Materiel via novel technologies such as nanotechnology, Micro-electromechanical Systems (MEMS), meta-materials, flexible electronics, electrochromics, electroluminescence, etc. This paper will provide the reader with an overview of the Active Coatings Technologies Program, including an update of the on-going Smart Coatings Materiel Program, its progress thus far, description of the prototype Smart Coatings Systems and research tasks as well as future nanotechnology concepts, and applications for the Department of Defense.

Structural and spectroscopic characteristics of Eu3+-doped tungsten phosphate glasses

Science.gov (United States)

Dousti, M. Reza; Poirier, Gael Yves; de Camargo, Andrea Simone Stucchi

2015-07-01

Tungsten based phosphate glasses are interesting non-crystalline materials, commonly known for photochromic and electrochromic effects, but also promising hosts for luminescent trivalent rare earth ions. Despite very few reports in the literature, association of the host´s functionalities with the efficient emissions of the dopant ions in the visible and near-infrared spectra could lead to novel applications. This work reports the preparation and characterization of glasses with the new composition 4(Sb2O3)96-x(50WO3 50NaPO3)xEu2O3 where x = 0, 0.1, 0.25, 0.5 and 1.0 mol%, obtained by the melt quenching technique. The glasses present large density (∼4.6 g cm-3), high glass transition temperature (∼480 °C) and high thermal stability against crystallization. Upon excitation at 464 nm, the characteristic emissions of Eu3+ ions in the red spectral region are observed with high intensity. The Judd-Ofelt intensity parameters Ω2 = 6.86 × 10-20, Ω4 = 3.22 × 10-20 and Ω6 = 8.2 × 10-20 cm2 were calculated from the emission spectra and found to be higher than those reported for other phosphate glass compositions. An average excited state lifetime value of 1.2 ms, was determined by fitting the luminescence decay curves with single exponential functions and it is comparable or higher than those of other oxide glasses.

Photochemical solar cells based on dye-sensitization of nanocrystalline TiO{sub 2}

Energy Technology Data Exchange (ETDEWEB)

Deb, S.K.; Ellingson, R.; Ferrere, S.; Frank, A.J.; Gregg, B.A.; Nozik, A.J.; Park, N.; Schlichthoerl, G. [National Renewable Energy Lab., Golden, CO (United States)

1998-09-01

A photoelectrochemical solar cell that is based on the dye-sensitization of thin nanocrystalline films of TiO{sub 2} (anatase) nanoparticles in contact with a non-aqueous liquid electrolyte is described. The cell, fabricated at NREL, shows a conversion efficiency of {approximately} 9.2% at AM1.5, which approaches the best reported value of 10--11% by Graetzel at EPFL in Lausanne, Switzerland. The femtosecond (fs) pump-probe spectroscopy has been used to time resolve the injection of electrons into the conduction band of nanocrystalline TiO{sub 2} films under ambient conditions following photoexcitation of the adsorbed Ru(II)-complex dye. The measurement indicates an instrument-limited {minus}50 fs upper limit on the electron injection time. The authors also report the sensitization of nanocrystalline TiO{sub 2} by a novel iron-based dye, CIS-[Fe{sup II}(2,2{prime}-bipyridine-4,4,{prime}-dicarboxylic acid){sub 2}(CN){sub 2}], a chromophore with an extremely short-lived, nonemissive excited state. The dye also exhibits a unique band selective sensitization through one of its two absorption bands. The operational principle of the device has been studied through the measurement of electric field distribution within the device structure and studies on the pH dependence of dye-redox potential. The incorporation of WO{sub 3}-based electrochromic layer into this device has led to a novel photoelectrochromic device structure for smart window application.

Developments in hot-filament metal oxide deposition (HFMOD)

International Nuclear Information System (INIS)

Durrant, Steven F.; Trasferetti, Benedito C.; Scarminio, Jair; Davanzo, Celso U.; Rouxinol, Francisco P.M.; Gelamo, Rogerio V.; Bica de Moraes, Mario A.

2008-01-01

Hot-filament metal oxide deposition (HFMOD) is a variant of conventional hot-filament chemical vapor deposition (HFCVD) recently developed in our laboratory and successfully used to obtain high-quality, uniform films of MO x , WO x and VO x . The method employs the controlled oxidation of a filament of a transition metal heated to 1000 deg. C or more in a rarefied oxygen atmosphere (typically, of about 1 Pa). Metal oxide vapor formed on the surface of the filament is transported a few centimetres to deposit on a suitable substrate. Key system parameters include the choice of filament material and diameter, the applied current and the partial pressures of oxygen in the chamber. Relatively high film deposition rates, such as 31 nm min -1 for MoO x , are obtained. The film stoichiometry depends on the exact deposition conditions. MoO x films, for example, present a mixture of MoO 2 and MoO 3 phases, as revealed by XPS. As determined by Li + intercalation using an electrochemical cell, these films also show a colouration efficiency of 19.5 cm 2 C -1 at a wavelength of 700 nm. MO x and WO x films are promising in applications involving electrochromism and characteristics of their colouring/bleaching cycles are presented. The chemical composition and structure of VO x films examined using IRRAS (infrared reflection-absorption spectroscopy), RBS (Rutherford backscattering spectrometry) and XPS (X-ray photoelectron spectrometry) are also presented

Electroactive semi-interpenetrating polymer networks architecture with tunable IR reflectivity

Science.gov (United States)

Chevrot, C.; Teyssié, D.; Verge, P.; Goujon, L.; Tran-Van, F.; Vidal, F.; Aubert, P. H.; Peralta, S.; Sauques, L.

2011-04-01

A promising alternative of multi-layered devices showing electrochromic properties results from the design of a self-supported semi-interpenetrating polymer network (semi-IPN) including an electronic conductive polymer (ECP) formed within. The formation of the ECP in the network has already been described by oxidative polymerization using iron trichloride as an oxidant and leading to conducting semi-IPN with mixed electronic and ionic conductivities as well as convenient mechanical properties. This presentation relates to the elaboration of such semi-IPN using polyethyleneoxide (PEO) network or a PEO/NBR (Nitrile Butadiene Rubber) IPN in which a linear poly (3,4-ethylenedioxythiophene) (PEDOT) is formed symmetrically and selectively as very thin layers very next to the two main faces of the film matrix. PEO/PEDOT semi-IPNs lead to interesting optical reflective properties in the IR between 0.8 and 25 μm. Reflectance contrasts up to 35 % is observed when, after swelling in an ionic liquid, a low voltage is applied between the two main faces of the film. However the low flexibility and brittleness of the film and a slow degradation in air at temperature up from 60°C prompted to replace the PEO matrix by a flexible PEO/NBR IPN one. Indeed, the combination of NBR and PEO in an IPN leads to materials possessing flexible properties, good ionic conductivity at 25°C as well as a better resistance to thermal ageing. Finally, NBR/PEO/PEDOT semi-IPNs allow observing comparable reflectance contrast in the IR range than those shown by PEO/PEDOT semi-IPNs.

Developments in hot-filament metal oxide deposition (HFMOD)

Energy Technology Data Exchange (ETDEWEB)

Durrant, Steven F. [Laboratorio de Plasmas Tecnologicos, Campus Experimental de Sorocaba, Universidade Estadual Paulista (UNESP), Avenida Tres de Marco, 511, Alto de Boa Vista, 18087-180 Sorocaba, SP (Brazil)], E-mail: steve@sorocaba.unesp.br; Trasferetti, Benedito C. [Departamento de Policia Federal, Superintendencia Regional no Piaui, Setor Tecnico-Cientifico, Avenida Maranhao, 1022/N, 64.000-010, Teresina, PI (Brazil); Scarminio, Jair [Departamento de Fisica, Universidade Estadual de Londrina (UEL), 86051-990, Londrina, PR (Brazil); Davanzo, Celso U. [Instituto de Quimica, Universidade Estadual de Campinas (UNICAMP), 13083-970, Campinas, SP (Brazil); Rouxinol, Francisco P.M.; Gelamo, Rogerio V.; Bica de Moraes, Mario A. [Laboratorio de Processos de Plasma, Departamento de Fisica Aplicada, Instituto de Fisica Gleb Wataghin, Universidade Estadual de Campinas (UNICAMP), 13083-970, Campinas, SP (Brazil)

2008-01-15

Hot-filament metal oxide deposition (HFMOD) is a variant of conventional hot-filament chemical vapor deposition (HFCVD) recently developed in our laboratory and successfully used to obtain high-quality, uniform films of MO{sub x}, WO{sub x} and VO{sub x}. The method employs the controlled oxidation of a filament of a transition metal heated to 1000 deg. C or more in a rarefied oxygen atmosphere (typically, of about 1 Pa). Metal oxide vapor formed on the surface of the filament is transported a few centimetres to deposit on a suitable substrate. Key system parameters include the choice of filament material and diameter, the applied current and the partial pressures of oxygen in the chamber. Relatively high film deposition rates, such as 31 nm min{sup -1} for MoO{sub x}, are obtained. The film stoichiometry depends on the exact deposition conditions. MoO{sub x} films, for example, present a mixture of MoO{sub 2} and MoO{sub 3} phases, as revealed by XPS. As determined by Li{sup +} intercalation using an electrochemical cell, these films also show a colouration efficiency of 19.5 cm{sup 2} C{sup -1} at a wavelength of 700 nm. MO{sub x} and WO{sub x} films are promising in applications involving electrochromism and characteristics of their colouring/bleaching cycles are presented. The chemical composition and structure of VO{sub x} films examined using IRRAS (infrared reflection-absorption spectroscopy), RBS (Rutherford backscattering spectrometry) and XPS (X-ray photoelectron spectrometry) are also presented.

Facile one-pot synthesis of Ni2+-doped (NH4)2V3O8 nanoflakes@Ni foam with visible-light-driven photovoltaic behavior for supercapacitor application

Science.gov (United States)

Zhou, Qingfeng; Gong, Yun; Lin, Jianhua

2018-05-01

In the present work, Ni2+-doped (NH4)2V3O8 nanoflakes are in situ grown on Ni foam through a facile one-pot hydrothermal technique in a NH4VO3 aqueous solution. The Ni2+-doped (NH4)2V3O8@Ni foam composite material can be used as binder- and conductivity agent-free electrode in supercapacitor, it manifests a large specific capacitance of 465.5 F g-1 at a current density of 0.2 A g-1 and a superior rate capability of 317.5 F g-1 at 10 A g-1, which is beneficial from its three-dimensional porous architecture cross-linked by the ultrathin Ni2+-doped (NH4)2V3O8 nanoflakes on Ni foam. Meanwhile, the Ni2+-doped (NH4)2V3O8@Ni foam//Activated carbon asymmetric supercapacitor can deliver a maximum energy density of 20.1 W h kg-1 at a power density of 752.0 W kg-1. Significantly, the Ni2+-doped (NH4)2V3O8@Ni foam electrode possesses reversible electrochromic behavior, and it shows obvious visible light-driven photoresponse with much higher specific capacitance (645.3 F g-1 at 0.5 A g-1) under illumination (650 nm > λ > 350 nm, 100 mW cm-2), which is probably associated with the semiconducting characteristics of the spin-polarized (NH4)2V3O8 and the quantum confinement effect of the nanoflakes.

Effect of carbon limitation on photosynthetic electron transport in Nannochloropsis oculata.

Science.gov (United States)

Zavřel, Tomáš; Szabó, Milán; Tamburic, Bojan; Evenhuis, Christian; Kuzhiumparambil, Unnikrishnan; Literáková, Petra; Larkum, Anthony W D; Raven, John A; Červený, Jan; Ralph, Peter J

2018-04-01

This study describes the impacts of inorganic carbon limitation on the photosynthetic efficiency and operation of photosynthetic electron transport pathways in the biofuel-candidate microalga Nannochloropsis oculata. Using a combination of highly-controlled cultivation setup (photobioreactor), variable chlorophyll a fluorescence and transient spectroscopy methods (electrochromic shift (ECS) and P 700 redox kinetics), we showed that net photosynthesis and effective quantum yield of Photosystem II (PSII) decreased in N. oculata under carbon limitation. This was accompanied by a transient increase in total proton motive force and energy-dependent non-photochemical quenching as well as slightly elevated respiration. On the other hand, under carbon limitation the rapid increase in proton motive force (PMF, estimated from the total ECS signal) was also accompanied by reduced conductivity of ATP synthase to protons (estimated from the rate of ECS decay in dark after actinic illumination). This indicates that the slow operation of ATP synthase results in the transient build-up of PMF, which leads to the activation of fast energy dissipation mechanisms such as energy-dependent non-photochemical quenching. N. oculata also increased content of lipids under carbon limitation, which compensated for reduced NAPDH consumption during decreased CO 2 fixation. The integrated knowledge of the underlying energetic regulation of photosynthetic processes attained with a combination of biophysical methods may be used to identify photo-physiological signatures of the onset of carbon limitation in microalgal cultivation systems, as well as to potentially identify microalgal strains that can better acclimate to carbon limitation. Copyright © 2018 Elsevier B.V. All rights reserved.

A resettable and reprogrammable keypad lock based on electrochromic Prussian blue films and biocatalysis of immobilized glucose oxidase in a bipolar electrode system.

Science.gov (United States)

Yu, Xue; Liang, Jiying; Yang, Tiangang; Gong, Mengjie; Xi, Dongman; Liu, Hongyun

2018-01-15

Herein, a resettable and reprogrammable biomolecular keypad lock on the basis of a closed bipolar electrode (BPE) system was established. In this system, one ITO electrode with immobilized chitosan (CS) and glucose oxidase (GOD), designated as CS-GOD, acted as one pole of BPE in the sensing cell; another ITO with electrodeposited Prussian blue (PB) films as the other pole in the reporting cell. The addition of ascorbic acid (AA) in the sensing cell with driving voltage (V tot ) at +2.5V would make the PB films become Prussian white (PW) in the reporting cell, accompanied by the color change from blue to nearly transparent. On the other hand, with the help of oxygen, the addition of glucose in the sensing cell with V tot at -1.5V would induce PW back to PB. The change of color and the corresponding UV-vis absorbance at 700nm for the PB/PW films in the reporting cell could be reversibly switched by changing the solute in the sensing cell between AA and glucose and then switching V tot between +2.5 and -1.5V. Based on these, a keypad lock was developed with AA, glucose and V tot as 3 inputs, and the color change of the PB/PW films as the output. This keypad lock system combined enzymatic catalysis with bipolar electrochemistry, demonstrating some unique advantages such as good reprogrammability, easy resettability and visual readout by naked eye. Copyright © 2017 Elsevier B.V. All rights reserved.

Dióxido de titânio sol-gel: propriedades e comportamento eletrocrômico Sol-gel titanium dioxide: properties and electrochromic behavior

Directory of Open Access Journals (Sweden)

Rita Aparecida Zoppi

2000-12-01

Full Text Available Titanium dioxide was prepared by hydrolysis and polycondensation of titanium tetraisopropoxide. TiO2 films were obtained by spin coating of the precursor solution on ITO substractes (glass covered with indium doped tin oxide. Films were prepared using different temperatures and hydrochloric acid contents. The effect of the drying temperature of the films (100 or 400ºC was also investigated. TiO2 films were characterized by cyclic voltammetry, chronoamperometry, ultraviolete-visible spectroscopy, scanning electron microscopy and X-ray diffractrometry.

Colorless to purple-red switching electrochromic anthraquinone imides with broad visible/near-IR absorptions in the radical anion state: simulation-aided molecular design.

Science.gov (United States)

Chen, Fengkun; Zhang, Jie; Jiang, Hong; Wan, Xinhua

2013-07-01

The large redshift of near-infrared (NIR) absorptions of nitro-substituted anthraquinone imide (Nitro-AQI) radical anions, relative to other AQI derivatives, is rationalized based on quantum chemical calculations. Calculations reveal that the delocalization effects of electronegative substitution in the radical anion states is dramatically enhanced, thus leading to a significant decrease in the HOMO-LUMO band gap in the radical anion states. Based on this understanding, an AQI derivative with an even stronger electron-withdrawing dicyanovinyl (di-CN) substituent was designed and prepared. The resulting molecule, di-CN-AQI, displays no absorption in the Vis/NIR region in the neutral state, but absorbs intensively in the range of λ=700-1000 (λmax ≈860 nm) and λ=1100-1800 nm (λmax ≈1400 nm) upon one-electron reduction; this is accompanied by a transition from a highly transmissive colorless solution to one that is purple-red. The relationship between calculated radical anionic HOMO-LUMO gaps and the electron-withdrawing capacity of the substituents is also determined by employing Hammett parameter, which could serve as a theoretical tool for further molecular design. Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Voltage-sensitive dye recording from networks of cultured neurons

Science.gov (United States)

Chien, Chi-Bin

This thesis describes the development and testing of a sensitive apparatus for recording electrical activity from microcultures of rat superior cervical ganglion (SCG) neurons by using voltage-sensitive fluorescent dyes.The apparatus comprises a feedback-regulated mercury arc light source, an inverted epifluorescence microscope, a novel fiber-optic camera with discrete photodiode detectors, and low-noise preamplifiers. Using an NA 0.75 objective and illuminating at 10 W/cm2 with the 546 nm mercury line, a typical SCG neuron stained with the styryl dye RH423 gives a detected photocurrent of 1 nA; the light source and optical detectors are quiet enough that the shot noise in this photocurrent--about.03% rms--dominates. The design, theory, and performance of this dye-recording apparatus are discussed in detail.Styryl dyes such as RH423 typically give signals of 1%/100 mV on these cells; the signals are linear in membrane potential, but do not appear to arise from a purely electrochromic mechanism. Given this voltage sensitivity and the noise level of the apparatus, it should be possible to detect both action potentials and subthreshold synaptic potentials from SCG cell bodies. In practice, dye recording can easily detect action potentials from every neuron in an SCG microculture, but small synaptic potentials are obscured by dye signals from the dense network of axons.In another microculture system that does not have such long and complex axons, this dye-recording apparatus should be able to detect synaptic potentials, making it possible to noninvasively map the synaptic connections in a microculture, and thus to study long-term synaptic plasticity.

Integrated MEMS-based variable optical attenuator and 10Gb/s receiver

Science.gov (United States)

Aberson, James; Cusin, Pierre; Fettig, H.; Hickey, Ryan; Wylde, James

2005-03-01

MEMS devices can be successfully commercialized in favour of competing technologies only if they offer an advantage to the customer in terms of lower cost or increased functionality. There are limited markets where MEMS can be manufactured cheaper than similar technologies due to large volumes: automotive, printing technology, wireless communications, etc. However, success in the marketplace can also be realized by adding significant value to a system at minimal cost or leverging MEMS technology when other solutions simply will not work. This paper describes a thermally actuated, MEMS based, variable optical attenuator that is co-packaged with existing opto-electronic devices to develop an integrated 10Gb/s SONET/SDH receiver. The configuration of the receiver opto-electronics and relatively low voltage availability (12V max) in optical systems bar the use of LCD, EO, and electro-chromic style attenuators. The device was designed and fabricated using a silicon-on-insulator (SOI) starting material. The design and performance of the device (displacement, power consumption, reliability, physical geometry) was defined by the receiver parameters geometry. This paper will describe how these design parameters (hence final device geometry) were determined in light of both the MEMS device fabrication process and the receiver performance. Reference will be made to the design tools used and the design flow which was a joint effort between the MEMS vendor and the end customer. The SOI technology offered a robust, manufacturable solution that gave the required performance in a cost-effective process. However, the singulation of the devices required the development of a new singulation technique that allowed large volumes of silicon to be removed during fabrication yet still offer high singulation yields.

Synthesis, Characterization and Conductivity Study of Poly(vinyl 4-HYDROXY-3-METHOXY Benzal) and its Sodio Salt in Solid State

Science.gov (United States)

Borah, P.; Hussain, S.; Dutta, A.

Among the various ion-conducting materials, polymer salt complexes are of current interest due to their possible application as solid electrolyte as well as their physical nature in advanced high-energy electrochemical devices such as batteries, fuel cells, electrochromic display devices, photo electro-chemical solar cells52-55 etc. The main advantages of polymeric electrolytes are their mechanical properties, ease of fabrication of thin films of desired sizes and their ability to form proper electrode-electrolyte contact. Polymer electrolyte usually consists of a polymer and a salt and is considered to be solid solutions in which the polymer functions as solvent. In the present paper the synthesis, characterization and the conductivity study of the polymer poly (vinyl 4-hydroxy-3-methoxy benzal) (PV-HMB) and its sodio salt (PV-HMB-Na) have been reported. The polymer was prepared by carrying out homogenous acetalization between the prepolymer poly vinylalcohol (PVA) and 4-hydroxy-3-methoxy benzaldehyde (vanilline). PVA was dissolved in dimethyl formamide (DMF) and lithium chloride (LiCl) system i.e., in non-aqueous medium. The sodio salt was prepared by alkalization. The polymer and its salt were characterized by IR, 1H NMR and DSC. Frequency and temperature dependence of ac conductivity has been studied to learn about the electrical conduction behaviour in this material. The electrical conductivity of the new polymeric salt was found to be in the range 10-4 to 10-6 Scm-1. There is about 103 to 104 fold increase in the conductivity of the new polymer salt. Apparent activation energy of the polymer and its salt were found to be 0.139 and 0.08998 ev respectively.

Characterization of cobalt oxide thin films prepared by a facile spray pyrolysis technique using perfume atomizer

Energy Technology Data Exchange (ETDEWEB)

Louardi, A.; Rmili, A.; Ouachtari, F.; Bouaoud, A. [Laboratoire des Hautes Energies, Sciences de l' Ingenierie et Reacteurs (LHESIR), Equipe Ingenierie et Materiaux (INMA), Departement de Physique, Faculte des Sciences, Kenitra (Morocco); Elidrissi, B., E-mail: e.bachir@mailcity.com [Laboratoire des Hautes Energies, Sciences de l' Ingenierie et Reacteurs (LHESIR), Equipe Ingenierie et Materiaux (INMA), Departement de Physique, Faculte des Sciences, Kenitra (Morocco); Erguig, H. [Laboratoire des Hautes Energies, Sciences de l' Ingenierie et Reacteurs (LHESIR), Equipe Ingenierie et Materiaux (INMA), Departement de Physique, Faculte des Sciences, Kenitra (Morocco)

2011-09-15

Highlights: > Co{sub 3}O{sub 4} thin films show a micro porous structure. > Co{sub 3}O{sub 4} thin films are formed with spherical grains less than 50 nm in diameter. > The porous structure of Co{sub 3}O{sub 4} films is expected to have promising application in electrochromism. - Abstract: Cobalt oxide (Co{sub 3}O{sub 4}) thin films were prepared by a facile spray pyrolysis technique using perfume atomizer from aqueous solution of hydrated cobalt chloride salt (CoCl{sub 2}.6H{sub 2}O) as source of cobalt. The films were deposited onto the amorphous glass substrates kept at different temperatures (300-500 deg. C). The influences of molar concentration of the starting solution and substrate temperature on the structural, morphological and optical properties of (Co{sub 3}O{sub 4}) thin films were studied. It was found from X-ray diffraction (XRD) analysis that the films prepared with molar concentration greater than 0.025 M/L were polycrystalline spinel type cubic structure. The preferred orientation of the crystallites of these films changes gradually from (6 2 2) to (1 1 1) when the substrate temperature increases. By Raman spectroscopy, five Raman active modes characteristic of Co{sub 3}O{sub 4} spinel type cubic structure were found and identified at 194, 484, 522, 620 and 691 cm{sup -1}. The scanning electron microscopy (SEM) images showed micro porous structure with very fine grains less than 50 nm in diameter. These films exhibited also a transmittance value of about 70% in the visible and infra red range.

Factors influencing charge capacity of vanadium pentoxide thin films during lithium ion intercalation/deintercalation cycles

International Nuclear Information System (INIS)

Alamarguy, D.; Castle, J. E.; Ibris, N.; Salvi, A. M.

2007-01-01

The intercalation of vanadium pentoxide by lithium ions leads to a change in optical properties, a process that is of value in thin-film electrochromic devices. In this study, films of V 2 O 5 , deposited on indium tin oxide (ITO) glass coupons by a sol-gel process, were challenged by increasing numbers of charge-discharge cycles ranging from 72 to 589 full cycles. The samples were characterized by x-ray photoelectron spectroscopy (XPS) and then examined in the deintercalated state by time-of-flight secondary ion mass spectroscopy (SIMS). XPS enabled measurement of the thickness and composition of the solid-electrolyte interface and provided evidence of the residual V 4+ concentration within the top few nanometers of the surface. The SIMS profile gave direct information on the thickness of the films and on the thickness loss caused by rinsing the samples after the electrochemical exposure. Determination, by SIMS, of the concentration of lithium ions has enabled a correction to be made for the amount of inactive material within the electrochemically active region of the film. The SIMS depth profiles for lithium in the four samples are similar, with a marked buildup of Li at the interface with the ITO. This interphase zone had a thickness of ∼27 nm and was electrochemically inactive, enabling a further correction to be made. Thus, by means of the XPS and the SIMS results the chemistry and thickness of the films could be fully characterized. The remaining inconsistency between capacity (between 35% and 100% of the anticipated charge) and number of cycles is ascribed to edge effects arising from the method used for production of the coupons

Synthesis and electrochemical properties of novel, donor–acceptor pyrrole derivatives with 1,8-naphthalimide units and their polymers

International Nuclear Information System (INIS)

Ledwon, Przemyslaw; Brzeczek, Alina; Pluczyk, Sandra; Jarosz, Tomasz; Kuznik, Wojciech; Walczak, Krzysztof; Lapkowski, Mieczyslaw

2014-01-01

A new class of bipolar monomers with pyrrole or thiophene–pyrrole–thiophene as electron donor and 1,8-naphthalimide as electron acceptor unit is reported. Donor–acceptor conjugated polymers were generated electrochemically. The synthesis of monomers, optical, electrochemical and spectroelectrochemical properties supported by theoretical calculations are presented. 1,8-naphthalimide units were attached directly to pyrrole in compounds 1a and 2a or by different bridges in the case of 1b and 2b. Intra-molecular donor–acceptor interactions of the monomers and its polymers were investigated using cyclic voltammetry, in-situ UV–Vis-NIR, electron spin resonance (ESR) spectroelectrochemistry and fluorescence spectroscopy. Studied compounds present large discrepancy (up to 1.31 eV for 2a) between energy gap values determined through electrochemical and optical measurements. The Time-dependent density functional theory (TDDFT) calculations help to explain this discrepancy. This is caused by weak HOMO to LUMO transition, 2000 times weaker than HOMO −2 to LUMO or HOMO to LUMO +1 transition. Altering the structure of monomers yields different stability and properties of obtained polymers. The p- and n-doping processes are separated. Anions are localized mainly on 1,8-naphthalimide units. Cations are localized mainly on pyrrole or thiophene–pyrrole–thiophene moiety and their polymer chains. Attachment of the additional thiophene units decreases the oxidation potential of the monomer and reduces the influence of the steric hindrance between 1,8-naphthalimide moiety and polymer/oligomers chain. This new class of model compounds is promising for use as a material with enhanced charge separation for wide range of optoelectronic, electrochromic and photovoltaic applications

Self-assembled micro-/nanostructured WO3 thin films by aqueous chemical growth and their applications in H2 and CO2 sensing

Science.gov (United States)

Sone, B. T.; Nkosi, S. S.; Nkosi, M. M.; Coetsee-Hugo, E.; Swart, H. C.; Maaza, M.

2018-05-01

Application of thin film technology is increasing in many areas such as energy production, energy saving, telecommunications, protective and smart coatings, etc. This increased application creates a need for simple, cost-effective methods for the synthesis of highly multifunctional metal oxide thin films. The technique of Aqueous Chemical Growth is presented in this paper as a simple inexpensive means of producing WO3 thin films that find applications in gas sensing, electrochromism and photocatalysis. We demonstrate, through this technique, that heterogeneous nucleation and growth of WO3 thin films on plain glass substrates takes place at low pHs and low temperatures (75-95 °C) without the use of surfactants and template directing methods. The substrates used needed no surface-modification. On the plain glass substrates (soda lime silicates) a variety of micro-nanostructures could be observed most important of which were nanoplatelets that acted as a basic building block for the self-assembly of more hierarchical 3-d microspheres and thin films. The dominant crystallographic structure observed through X-ray diffraction analysis was found to be hexagonal-WO3 and monoclinic WO3. The thin films produced showed a fair degree of porosity. Some of the thin films on glass showed ability to sense, unaided, H2 at 250 °C. Sensor responses were observed to be 1 - 2 orders of magnitude. The films also demonstrated potential to sense CO2 even though this could only be achieved using high concentrations of CO2 gas at temperatures of 300 °C and above. The sensor responses at 300 °C were estimated to be less than 1 order of magnitude.

Flat-panel electronic displays: a triumph of physics, chemistry and engineering.

Science.gov (United States)

Hilsum, Cyril

2010-03-13

This paper describes the history and science behind the development of modern flat-panel displays, and assesses future trends. Electronic displays are an important feature of modern life. For many years the cathode ray tube, an engineering marvel, was universal, but its shape was cumbersome and its operating voltage too high. The need for a flat-panel display, working at a low voltage, became imperative, and much research has been applied to this need. Any versatile flat-panel display will exploit an electro-optical effect, a transparent conductor and an addressing system to deliver data locally. The first need is to convert an electrical signal into a visible change. Two methods are available, the first giving emission of light, the second modulating ambient illumination. The most useful light-emitting media are semiconductors, historically exploiting III-V or II-VI compounds, but more recently organic or polymer semiconductors. Another possible effect uses gas plasma discharges. The modulating, or subtractive, effects that have been studied include liquid crystals, electrophoresis, electrowetting and electrochromism. A transparent conductor makes it possible to apply a voltage to an extended area while observing the results. The design is a compromise, since the free electrons that carry current also absorb light. The first materials used were metals, but some semiconductors, when heavily doped, give a better balance, with high transmission for a low resistance. Delivering data unambiguously to a million or so picture elements across the display area is no easy task. The preferred solution is an amorphous silicon thin-film transistor deposited at each cross-point in an X-Y matrix. Success in these endeavours has led to many applications for flat-panel displays, including television, flexible displays, electronic paper, electronic books and advertising signs.

NDH-Mediated Cyclic Electron Flow Around Photosystem I is Crucial for C4 Photosynthesis.

Science.gov (United States)

Ishikawa, Noriko; Takabayashi, Atsushi; Noguchi, Ko; Tazoe, Youshi; Yamamoto, Hiroshi; von Caemmerer, Susanne; Sato, Fumihiko; Endo, Tsuyoshi

2016-10-01

C 4 photosynthesis exhibits efficient CO 2 assimilation in ambient air by concentrating CO 2 around ribulose 1,5-bisphosphate carboxylase/oxygenase (Rubisco) through a metabolic pathway called the C 4 cycle. It has been suggested that cyclic electron flow (CEF) around PSI mediated by chloroplast NADH dehydrogenase-like complex (NDH), an alternative pathway of photosynthetic electron transport (PET), plays a crucial role in C 4 photosynthesis, although the contribution of NDH-mediated CEF is small in C 3 photosynthesis. Here, we generated NDH-suppressed transformants of a C 4 plant, Flaveria bidentis, and showed that the NDH-suppressed plants grow poorly, especially under low-light conditions. CO 2 assimilation rates were consistently decreased in the NDH-suppressed plants under low and medium light intensities. Measurements of non-photochemical quenching (NPQ) of Chl fluorescence, the oxidation state of the reaction center of PSI (P700) and the electrochromic shift (ECS) of pigment absorbance indicated that proton translocation across the thylakoid membrane is impaired in the NDH-suppressed plants. Since proton translocation across the thylakoid membrane induces ATP production, these results suggest that NDH-mediated CEF plays a role in the supply of ATP which is required for C 4 photosynthesis. Such a role is more crucial when the light that is available for photosynthesis is limited and the energy production by PET becomes rate-determining for C 4 photosynthesis. Our results demonstrate that the physiological contribution of NDH-mediated CEF is greater in C 4 photosynthesis than in C 3 photosynthesis, suggesting that the mechanism of PET in C 4 photosynthesis has changed from that in C 3 photosynthesis accompanying the changes in the mechanism of CO 2 assimilation. © The Author 2016. Published by Oxford University Press on behalf of Japanese Society of Plant Physiologists. All rights reserved. For permissions, please email: journals.permissions@oup.com.

Graphite intercalated polyaniline composite with superior anticorrosive and hydrophobic properties, as protective coating material on steel surfaces

Energy Technology Data Exchange (ETDEWEB)

Rathnayake, R.M.N.M. [National Institute of Fundamental Studies, Kandy (Sri Lanka); Graduate School of Engineering, Toyota Technological Institute, 2-12-1 Hisakata, Tempaku, Nagoya 468-8511 (Japan); Mantilaka, M.M.M.G.P.G. [Sri Lanka Institute of Nanotechnology, Nanotechnology and Science Park, Mahenwatte, Pitipana, Homagama (Sri Lanka); Hara, Masanori; Huang, Hsin-Hui [Graduate School of Engineering, Toyota Technological Institute, 2-12-1 Hisakata, Tempaku, Nagoya 468-8511 (Japan); Wijayasinghe, H.W.M.A.C., E-mail: athula@ifs.ac.lk [National Institute of Fundamental Studies, Kandy (Sri Lanka); Yoshimura, Masamichi [Graduate School of Engineering, Toyota Technological Institute, 2-12-1 Hisakata, Tempaku, Nagoya 468-8511 (Japan); Pitawala, H.M.T.G.A. [Department of Geology, University of Peradeniya, Peradeniya (Sri Lanka)

2017-07-15

Highlights: • In this paper, it has been utilized a novel method to prepare a new composite material of PANI/NPG graphite composite, using NPG vein graphite variety. • It is found that the composite works as an anti-corrosive coating on steel surfaces. Further, the prepared composite shows good hydrophobic ability, which is very useful in preventing corrosion on metal surfaces. • The prepared PANI/NPG composite material shows a significantly high corrosion resistance compared to alkyd resin/PANI coatings or alkyd resin coatings, on steel surfaces. - Abstract: Solid polymer composite systems are widely being used for potential technological applications in secondary energy sources and electrochromic devices. In this study, we synthesized and characterized a composite material composed of polyaniline (PANI) and natural needle platy (NPG) vein graphite. Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), cyclic voltammetry (CV), scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), micro-Raman analysis, thermogravimetric and differential thermal analysis (TGA/DTA), transmission electron microscopy (TEM) were used to study the structural and electrochemical properties of the prepared PANI/NPG graphite composite. XPS, FTIR, and micro-Raman analysis confirmed the existence of relevant functional groups and bonding in the prepared PANI/NPG composite material. The composite shows a very low corrosion rate, approximately 29 μm per year, and high hydrophobicity on steel surfaces, which helps to prevent the corrosion due to O{sub 2} penetration towards the metal surface. It indicates that the composite can be used as a high potential surface coating material to anticorrosion. The specific capacitance of PANI/NPG composite is 833.3 F g{sup −1}, which is higher than that of PANI. This synergistic electrical performance result proves the prepared PANI/NPG graphite composite as a suitable protective coating material for steel

Synthesis and characterization of yellow and green light emitting novel polymers containing carbazole and electroactive moieties

International Nuclear Information System (INIS)

Aydın, Aysel; Kaya, İsmet

2012-01-01

Graphical abstract: The homopolymer of 1,5-bis(3,6-di(thiophen-3-yl)-9H-carbazol-9-yl)pentane and the copolymer with EDOT of 1,2-bis(2-(3,6-di(thiophen-3-yl)-9H-carbazol-9-yl)ethoxy)ethane were synthesized via electrochemical reaction on indium tin oxide (ITO)-coated glass plate. The obtained polymeric compounds were investigated as fluorescence properties in solution form. The synthesized polymers showed good fluorescence property indicating tunable light emission with green and yellow colors. This shows that these polymers could be used in production of new polymeric light emitting diodes (PLED)s for green and yellow color emissions. - Abstract: The compounds 1,5-bis(3,6-di(thiophen-3-yl)-9H-carbazol-9-yl)pentane (B1) and 1,2-bis(2-(3,6-di(thiophen-3-yl)-9H-carbazol-9-yl)ethoxy)ethane (B2) were synthesized via Ullmann and Suzuki couplings. Additionally, the homopolymers and copolymers of these compounds with 3,4-ethylenedioxythiophene (EDOT) and thiophene (Th) were synthesized and coated onto an ITO-glass surface via electrochemical oxidative polymerization. The spectroelectrochemical and electrochromic properties of these compounds were also investigated. The switching ability of these polymers was measured as the percent transmittance (%T) at their point of maximum contrast. The solid state electrical conductivities of the polymeric films coated onto the ITO-glass surface were measured via the four point probe technique using an electrometer. The compounds were characterized by FT-IR and NMR, and their thermal stabilities were determined via TG measurements. Fluorescence measurements were performed using DMSO solutions, and the synthesized polymers emitted both green and yellow colors based on the tuning of the excitation wavelength, which indicates that these polymers could be used to produce new polymeric light emitting diodes (PLEDs) with green and yellow emissions.

NASA Tech Briefs, March 2011

Science.gov (United States)

2011-01-01

Topics covered include: Optimal Tuner Selection for Kalman-Filter-Based Aircraft Engine Performance Estimation; Airborne Radar Interferometric Repeat-Pass Processing; Plug-and-Play Environmental Monitoring Spacecraft Subsystem; Power-Combined GaN Amplifier with 2.28-W Output Power at 87 GHz; Wallops Ship Surveillance System; Source Lines Counter (SLiC) Version 4.0; Guidance, Navigation, and Control Program; Single-Frame Terrain Mapping Software for Robotic Vehicles; Auto Draw from Excel Input Files; Observation Scheduling System; CFDP for Interplanetary Overlay Network; X-Windows Widget for Image Display; Binary-Signal Recovery; Volumetric 3D Display System with Static Screen; MMIC Replacement for Gunn Diode Oscillators; Feature Acquisition with Imbalanced Training Data; Mount Protects Thin-Walled Glass or Ceramic Tubes from Large Thermal and Vibration Loads; Carbon Nanotube-Based Structural Health Monitoring Sensors; Wireless Inductive Power Device Suppresses Blade Vibrations; Safe, Advanced, Adaptable Isolation System Eliminates the Need for Critical Lifts; Anti-Rotation Device Releasable by Insertion of a Tool; A Magnetically Coupled Cryogenic Pump; Single Piezo-Actuator Rotary-Hammering Drill; Fire-Retardant Polymeric Additives; Catalytic Generation of Lift Gases for Balloons; Ionic Liquids to Replace Hydrazine; Variable Emittance Electrochromics Using Ionic Electrolytes and Low Solar Absorptance Coatings; Spacecraft Radiator Freeze Protection Using a Regenerative Heat Exchanger; Multi-Mission Power Analysis Tool; Correction for Self-Heating When Using Thermometers as Heaters in Precision Control Applications; Gravitational Wave Detection with Single-Laser Atom Interferometers; Titanium Alloy Strong Back for IXO Mirror Segments; Improved Ambient Pressure Pyroelectric Ion Source; Multi-Modal Image Registration and Matching for Localization of a Balloon on Titan; Entanglement in Quantum-Classical Hybrid; Algorithm for Autonomous Landing; Quantum-Classical Hybrid

Modeling the light-induced electric potential difference (ΔΨ), the pH difference (ΔpH) and the proton motive force across the thylakoid membrane in C3 leaves.

Science.gov (United States)

Lyu, Hui; Lazár, Dušan

2017-01-21

A model was constructed which includes electron transport (linear and cyclic and Mehler type reaction) coupled to proton translocation, counter ion movement, ATP synthesis, and Calvin-Benson cycle. The focus is on modeling of the light-induced total electric potential difference (ΔΨ) which in this model originates from the bulk phase electric potential difference (ΔΨ b ), the localized electric potential difference (ΔΨ c ), as well as the surface electric potential difference (ΔΨ s ). The measured dual wavelength transmittance signal (ΔA515-560nm, electrochromic shift) was used as a proxy for experimental ΔΨ. The predictions for theoretical ΔΨ vary with assumed contribution of ΔΨ s , which might imply that the measured ΔA515-560nm trace on a long time scale reflects the interplay of the ΔΨ components. Simulations also show that partitioning of proton motive force (pmf) to ΔΨ b and ΔpH components is sensitive to the stoichiometric ratio of H + /ATP, energy barrier for ATP synthesis, ionic strength, buffer capacity and light intensity. Our model shows that high buffer capacity promotes the establishment of ΔΨ b , while the formation of pH i minimum is not 'dissipated' but 'postponed' until it reaches the same level as that for low buffer capacity. Under physiologically optimal conditions, the output of the model shows that at steady state in light, the ΔpH component is the main contributor to pmf to drive ATP synthesis while a low ΔΨ b persists energizing the membrane. Our model predicts 11mV as the resting electric potential difference across the thylakoid membrane in dark. We suggest that the model presented in this work can be integrated as a module into a more comprehensive model of oxygenic photosynthesis. Copyright © 2016 Elsevier Ltd. All rights reserved.

Novel silica surface charge density mediated control of the optical properties of embedded optically active materials and its application for fiber optic pH sensing at elevated temperatures.

Science.gov (United States)

Wang, Congjun; Ohodnicki, Paul R; Su, Xin; Keller, Murphy; Brown, Thomas D; Baltrus, John P

2015-02-14

Silica and silica incorporated nanocomposite materials have been extensively studied for a wide range of applications. Here we demonstrate an intriguing optical effect of silica that, depending on the solution pH, amplifies or attenuates the optical absorption of a variety of embedded optically active materials with very distinct properties, such as plasmonic Au nanoparticles, non-plasmonic Pt nanoparticles, and the organic dye rhodamine B (not a pH indicator), coated on an optical fiber. Interestingly, the observed optical response to varying pH appears to follow the surface charge density of the silica matrix for all the three different optically active materials. To the best of our knowledge, this optical effect has not been previously reported and it appears universal in that it is likely that any optically active material can be incorporated into the silica matrix to respond to solution pH or surface charge density variations. A direct application of this effect is for optical pH sensing which has very attractive features that can enable minimally invasive, remote, real time and continuous distributed pH monitoring. Particularly, as demonstrated here, using highly stable metal nanoparticles embedded in an inorganic silica matrix can significantly improve the capability of pH sensing in extremely harsh environments which is of increasing importance for applications in unconventional oil and gas resource recovery, carbon sequestration, water quality monitoring, etc. Our approach opens a pathway towards possible future development of robust optical pH sensors for the most demanding environmental conditions. The newly discovered optical effect of silica also offers the potential for control of the optical properties of optically active materials for a range of other potential applications such as electrochromic devices.

Wavelength Dispersive X-ray Fluorescence Spectrometry for the Analysis of Organic Polymer Film

International Nuclear Information System (INIS)

Choi, Yong Suk; Park, Yong Joon; Kim, Jong Yun

2008-01-01

Recently, many studies have been focused on the thin films because there are numerous industrial processes relevant to thin films such as fuel cells, sensors, lubricants, coatings, and so on. Physical and chemical properties of solid surface have been modified by ultra-thin coatings such as Langmuir-Blodgett (LB) method with a variety of types of organic functional materials for the specific purposes in many applications. In addition, the layer-by-layer technique using polyelectrolyte films are now of interest as biosensors, electrochromic and electroluminescent devices, etc. In general, several methods such as X-ray or neutron reflectivity, and quartz crystal microbalance (QCM) have been utilized for the thin film analysis. These optical techniques can measure the film thicknesses up to hundreds of nanometers while X-ray photoelectron spectroscopy is widely used to study a few nanometers thick films. Other methods such as X-ray Photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), and atom force microscopy (AFM) have also been used in the film analysis in spite of some disadvantages for each method. X-ray fluorescence (XRF) has long been used as a rapid and simple analytical tool for the analysis of elemental composition of materials. XRF technique is suitable for on-line or in-line real-time monitoring because it is a non-destructive and rapid analysis with good precision and good accuracy at low cost. The aim of this work is to develop a new analytical technique for the quantitative analysis of polymer film on metal substrate. In the present study, Compton peak profile was investigated under different experimental conditions by using wavelength-dispersive XRF (WD-XRF). Compared to energy-dispersive XRF (ED-XRF), WD-XRF is more adequate in an accurate quantitative analysis of thin organic film

Semi-transparent ordered TiO{sub 2} nanostructures prepared by anodization of titanium thin films deposited onto the FTO substrate

Energy Technology Data Exchange (ETDEWEB)

Szkoda, Mariusz, E-mail: mariusz-szkoda@wp.pl [Department of Chemistry and Technology of Functional Materials, Faculty of Chemistry, Gdańsk University of Technology, Narutowicza 11/12, Gdańsk 80-233 (Poland); Lisowska-Oleksiak, Anna [Department of Chemistry and Technology of Functional Materials, Faculty of Chemistry, Gdańsk University of Technology, Narutowicza 11/12, Gdańsk 80-233 (Poland); Grochowska, Katarzyna [Centre for Plasma and Laser Engineering, Szewalski Institute of Fluid-Flow Machinery, Polish Academy of Science, Fiszera 14, 80-231 Gdańsk (Poland); Skowroński, Łukasz [Institute of Mathematics and Physics, UTP University of Science and Technology, Kaliskiego 7, 85-796 Bydgoszcz (Poland); Karczewski, Jakub [Faculty of Applied Physics and Mathematics, Gdańsk University of Technology, Narutowicza 11/12, 80-233 Gdańsk (Poland); Siuzdak, Katarzyna [Centre for Plasma and Laser Engineering, Szewalski Institute of Fluid-Flow Machinery, Polish Academy of Science, Fiszera 14, 80-231 Gdańsk (Poland)

2016-09-15

Highlights: • High quality titanium coatings were doposited using industrial magnetron sputtering equipment. • Semi-transparent TiO{sub 2} were prepared via anodization realized in various conditions. • Depending on electrolyte type, ordered tubular or porous TiO{sub 2} layers were obtained. • Prepared material can act as semiconducting layer in photovoltaic cells. - Abstract: In a significant amount of cases, the highly ordered TiO{sub 2} nanotube arrays grow through anodic oxidation of a titanium metal plate immersed in electrolyte containing fluoride ions. However, for some practical applications, e.g. solar cells or electrochromic windows, the semi-transparent TiO{sub 2} formed directly on the transparent, conductive substrate is very much desired. This work shows that high-quality Ti coating could be formed at room temperature using an industrial magnetron sputtering system within 50 min. Under optimized conditions, the anodization process was performed on 2 μm titanium films deposited onto the FTO (fluorine-tin-oxide) support. Depending on the electrolyte type, highly ordered tubular or porous titania layers were obtained. The fabricated samples, after their thermal annealing, were investigated using scanning electron microscopy, Raman spectroscopy and UV–vis spectroscopy in order to investigate their morphology, crystallinity and absorbance ability. The photocurrent response curves indicate that materials are resistant to the photocorrosion process and their activity is strongly connected to optical properties. The most transparent TiO{sub 2} films were fabricated when Ti was anodized in water electrolyte, whereas the highest photocurrent densities (12 μA cm{sup −2}) were registered for titania received after Ti anodization in ethylene glycol solution. The obtained results are of significant importance in the production of thin, semi-transparent titania nanostructures on a commercial scale.

Semi-transparent ordered TiO_2 nanostructures prepared by anodization of titanium thin films deposited onto the FTO substrate

International Nuclear Information System (INIS)

Szkoda, Mariusz; Lisowska-Oleksiak, Anna; Grochowska, Katarzyna; Skowroński, Łukasz; Karczewski, Jakub; Siuzdak, Katarzyna

2016-01-01

Highlights: • High quality titanium coatings were doposited using industrial magnetron sputtering equipment. • Semi-transparent TiO_2 were prepared via anodization realized in various conditions. • Depending on electrolyte type, ordered tubular or porous TiO_2 layers were obtained. • Prepared material can act as semiconducting layer in photovoltaic cells. - Abstract: In a significant amount of cases, the highly ordered TiO_2 nanotube arrays grow through anodic oxidation of a titanium metal plate immersed in electrolyte containing fluoride ions. However, for some practical applications, e.g. solar cells or electrochromic windows, the semi-transparent TiO_2 formed directly on the transparent, conductive substrate is very much desired. This work shows that high-quality Ti coating could be formed at room temperature using an industrial magnetron sputtering system within 50 min. Under optimized conditions, the anodization process was performed on 2 μm titanium films deposited onto the FTO (fluorine-tin-oxide) support. Depending on the electrolyte type, highly ordered tubular or porous titania layers were obtained. The fabricated samples, after their thermal annealing, were investigated using scanning electron microscopy, Raman spectroscopy and UV–vis spectroscopy in order to investigate their morphology, crystallinity and absorbance ability. The photocurrent response curves indicate that materials are resistant to the photocorrosion process and their activity is strongly connected to optical properties. The most transparent TiO_2 films were fabricated when Ti was anodized in water electrolyte, whereas the highest photocurrent densities (12 μA cm"−"2) were registered for titania received after Ti anodization in ethylene glycol solution. The obtained results are of significant importance in the production of thin, semi-transparent titania nanostructures on a commercial scale.

How do 10-camphorsulfonic acid, silver or aluminum nanoparticles influence optical, electrochemical, electrochromic and photovoltaic properties of air and thermally stable triphenylamine-based polyazomethine with carbazole moieties?

Czech Academy of Sciences Publication Activity Database

Ivan, A.; Boharewicz, B.; Tazbir, I.; Filapek, M.; Korona, P.K.; Wróbel, Piotr; Stefaniuk, T.; Ciesielski, A.; Wojtkiewicz, J.; Wronkowska, A.A.; Wronkowski, A.; Zboromirska-Wnukiewicz, B.; Grankowska-Ciechanowicz, S.; Kaminska, M.; Szoplik, T.

2015-01-01

Roč. 185, December (2015), s. 198-210 ISSN 0013-4686 Institutional support: RVO:67985882 Keywords : refraction index * nanoparticles * bulk heterojunction polymer solar cells Subject RIV: JA - Electronics ; Optoelectronics, Electrical Engineering Impact factor: 4.803, year: 2015

Modification of doping front migration in electrochemical devices and application to organic electronics

International Nuclear Information System (INIS)

Nolte, Marius; Wan Xianglong; Kopp, Olga; Hermes, Ina; Panz, Jan; Rahmanian, Afsaneh; Knoll, Meinhard

2011-01-01

Research highlights: → In this paper we demonstrate several ways of tuning the doping front migration process in polymer electronic multilayer structures for the first time. By altering the migration layer thickness the migration velocity may be controlled and it is possible to switch between migration mechanisms. The mechanism of delamination produces rapid jumps in migration velocity, while the addition of 2-hydroxyethylcellulose (HEC) can inhibit this effect. In case of vapor activation the migration velocity may be influenced by the relative humidity or by varying the concentration of hygroscopic salts added to the migration layer. The migration mechanisms can be explained in terms of diffusion, capillary transport, and delamination. Tuning the migration process may be used to construct polymer electronic structures such as enhancement and depletion type pseudo transistors and electrical switches (ON-OFF and OFF-ON) with an improved switching time of several minutes. The doping front width is determined by microscopic optical absorption spectroscopy and can be controlled by the concentration of the doping solution. In case of low concentrations the electrochromic effect of the double front is observed. - Abstract: We demonstrate several methods of modifying the doping front migration process in multilayer structures, enabling control of migration velocity and switching between different migration mechanisms. Sharp jumps in migration velocity may be induced using a delamination effect. The influence of migration layer thickness and composition is examined. Migration velocity may also be influenced by exposing the system to a defined relative humidity or by varying the concentration of a hygroscopic salt in the migration layer. The migration mechanisms can be explained in terms of diffusion, capillary transport, and delamination. By tailoring the migration process a variety of polymer electronic structures such as pseudo transistors (enhancement and depletion

PREFACE: INERA Workshop: Transition Metal Oxide Thin Films-functional Layers in "Smart windows" and Water Splitting Devices. Parallel session of the 18th International School on Condensed Matter Physics

Science.gov (United States)

2014-11-01

The Special issue presents the papers for the INERA Workshop entitled "Transition Metal Oxides as Functional Layers in Smart windows and Water Splitting Devices", which was held in Varna, St. Konstantin and Elena, Bulgaria, from the 4th-6th September 2014. The Workshop is organized within the context of the INERA "Research and Innovation Capacity Strengthening of ISSP-BAS in Multifunctional Nanostructures", FP7 Project REGPOT 316309 program, European project of the Institute of Solid State Physics at the Bulgarian Academy of Sciences. There were 42 participants at the workshop, 16 from Sweden, Germany, Romania and Hungary, 11 invited lecturers, and 28 young participants. There were researchers present from prestigious European laboratories which are leaders in the field of transition metal oxide thin film technologies. The event contributed to training young researchers in innovative thin film technologies, as well as thin films characterization techniques. The topics of the Workshop cover the field of technology and investigation of thin oxide films as functional layers in "Smart windows" and "Water splitting" devices. The topics are related to the application of novel technologies for the preparation of transition metal oxide films and the modification of chromogenic properties towards the improvement of electrochromic and termochromic device parameters for possible industrial deployment. The Workshop addressed the following topics: Metal oxide films-functional layers in energy efficient devices; Photocatalysts and chemical sensing; Novel thin film technologies and applications; Methods of thin films characterizations; From the 37 abstracts sent, 21 manuscripts were written and later refereed. We appreciate the comments from all the referees, and we are grateful for their valuable contributions. Guest Editors: Assoc. Prof. Dr.Tatyana Ivanova Prof. DSc Kostadinka Gesheva Prof. DSc Hassan Chamatti Assoc. Prof. Dr. Georgi Popkirov Workshop Organizing Committee Prof