Sample records for eibj nanogap fabrication

  1. Fabrication of a Horizontal and a Vertical Large Surface Area Nanogap Electrochemical Sensor

    Directory of Open Access Journals (Sweden)

    Jules L. Hammond


    Full Text Available Nanogap sensors have a wide range of applications as they can provide accurate direct detection of biomolecules through impedimetric or amperometric signals. Signal response from nanogap sensors is dependent on both the electrode spacing and surface area. However, creating large surface area nanogap sensors presents several challenges during fabrication. We show two different approaches to achieve both horizontal and vertical coplanar nanogap geometries. In the first method we use electron-beam lithography (EBL to pattern an 11 mm long serpentine nanogap (215 nm between two electrodes. For the second method we use inductively-coupled plasma (ICP reactive ion etching (RIE to create a channel in a silicon substrate, optically pattern a buried 1.0 mm × 1.5 mm electrode before anodically bonding a second identical electrode, patterned on glass, directly above. The devices have a wide range of applicability in different sensing techniques with the large area nanogaps presenting advantages over other devices of the same family. As a case study we explore the detection of peptide nucleic acid (PNA−DNA binding events using dielectric spectroscopy with the horizontal coplanar device.

  2. The fabrication and characterization of adjustable nanogaps between gold electrodes on chip for electrical measurement of single molecules

    Energy Technology Data Exchange (ETDEWEB)

    Tian Jinghua; Yang Yang; Liu Bo; Wu Deyin; Tian Zhongqun [State Key Laboratory of Physical Chemistry of Solid Surfaces and LIA CNRS XiamENS ' NanoBioChem' , College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005, Fujian (China); Schoellhorn, Bernd; Maisonhaute, Emmanuel; Muns, Anna Serra; Chen Yong; Amatore, Christian [UMR CNRS 8640 ' PASTEUR' and LIA CNRS XiamENS ' NanoBioChem' , Ecole Normale Superieure, Universite Pierre et Marie Curie-Paris 6, 24 rue Lhomond, 75231 Paris Cedex 05 (France); Tao, Nong-Jian, E-mail:, E-mail: [Ira A Fulton School of Engineering and Center for Bioelectronics and Biosensors, Biodesign Institute, Arizona State University, Tempe, AZ 85287-6206 (United States)


    This work reports on a new method to fabricate mechanically controllable break junctions (MCBJ) with finely adjustable nanogaps between two gold electrodes on solid state chips for characterizing electron transport properties of single molecules. The simple, low cost, robust and reproducible fabrication method combines conventional photolithography, chemical etching and electrodeposition to produce suspended electrodes separated with nanogaps. The MCBJ devices fabricated by the method can undergo many cycles in which the nanogap width can be precisely and repeatedly varied from zero to several nanometers. The method improves the success rate of the MCBJ experiments. Using these devices the electron transport properties of a typical molecular system, commercially available benzene-1,4-dithiol (BDT), have been studied. The I-V and G-V characteristic curves of BDT and the conductance value for a single BDT molecule established the excellent device suitability for molecular electronics research.

  3. Fabricating Nanogaps in YBa2 Cu3 O7 -δ for Hybrid Proximity-Based Josephson Junctions (United States)

    Baghdadi, Reza; Arpaia, Riccardo; Charpentier, Sophie; Golubev, Dmitri; Bauch, Thilo; Lombardi, Floriana


    The advances of nanotechnologies applied to high-critical-temperature superconductors (HTSs) have recently given a huge boost to the field, opening new prospectives for their integration in hybrid devices. The feasibility of this research goes through the realization of HTS nanogaps with superconductive properties close to the as-grown bulk material at the nanoscale. Here we present a fabrication approach allowing the realization of YBa2 Cu3 O7 -δ (YBCO) nanogaps with dimensions as small as 35 nm. To assess the quality of the nanogaps, we measure, before and after an ozone treatment, the current-voltage characteristics and the resistance versus temperature of YBCO nanowires with various widths and lengths, fabricated by using different lithographic processes. The analysis of the superconducting transition with a thermally activated vortex-entry model allows us to determine the maximum damage the nanowires undergo during the patterning which relates to the upper bound for the dimension of the nanogap. We find that the effective width of the nanogap is of the order of 100 nm at the superconducting transition temperature while retaining the geometrical value of about 35 nm at lower temperatures. The feasibility of the nanogaps for hybrid Josephson devices is demonstrated by bridging them with thin Au films. We detect a Josephson coupling up to 85 K with an almost ideal magnetic-field response of the Josephson current. These results pave the way for the realization of complex hybrid devices, where tiny HTS nanogaps can be instrumental to study the Josephson effect through barriers such as topological insulators or graphene.

  4. Fabrication of reproducible sub-5 nm nanogaps by a focused ion beam and observation of Fowler-Nordheim tunneling

    Energy Technology Data Exchange (ETDEWEB)

    Li, Hu; Wani, Ishtiaq H.; Hayat, Aqib; Leifer, Klaus, E-mail: [Appled Materials Science, Department of Engineering Sciences, Uppsala University, Box 534, 75121 Uppsala (Sweden); Jafri, S. Hassan M. [Appled Materials Science, Department of Engineering Sciences, Uppsala University, Box 534, 75121 Uppsala (Sweden); Department of Electrical Engineering, Mirpur University of Science and Technology, Mirpur, Azad Kashmir, 10250 (Pakistan)


    Creating a stable high resistance sub-5 nm nanogap in between conductive electrodes is one of the major challenges in the device fabrication of nano-objects. Gap-sizes of 20 nm and above can be fabricated reproducibly by the precise focusing of the ion beam and careful milling of the metallic lines. Here, by tuning ion dosages starting from 4.6 × 10{sup 10} ions/cm and above, reproducible nanogaps with sub-5 nm sizes are milled with focused ion beam. The resistance as a function of gap dimension shows an exponential behavior, and Fowler-Nordheim tunneling effect was observed in nanoelectrodes with sub-5 nm nanogaps. The application of Simmon's model to the milled nanogaps and the electrical analysis indicates that the minimum nanogap size approaches to 2.3 nm.

  5. Fabrication of nano-gap electrode arrays by the construction and selective chemical etching of nano-crosswire stacks (United States)

    Son, Kyung-Ah (Inventor); Prokopuk, Nicholas (Inventor)


    Methods of fabricating nano-gap electrode structures in array configurations, and the structures so produced. The fabrication method involves depositing first and second pluralities of electrodes comprising nanowires using processes such as lithography, deposition of metals, lift-off processes, and chemical etching that can be performed using conventional processing tools applicable to electronic materials processing. The gap spacing in the nano-gap electrode array is defined by the thickness of a sacrificial spacer layer that is deposited between the first and second pluralities of electrodes. The sacrificial spacer layer is removed by etching, thereby leaving a structure in which the distance between pairs of electrodes is substantially equal to the thickness of the sacrificial spacer layer. Electrode arrays with gaps measured in units of nanometers are produced. In one embodiment, the first and second pluralities of electrodes are aligned in mutually orthogonal orientations.

  6. Semiconductor-Free Nonvolatile Resistive Switching Memory Devices Based on Metal Nanogaps Fabricated on Flexible Substrates via Adhesion Lithography

    KAUST Repository

    Semple, James


    Electronic memory cells are of critical importance in modern-day computing devices, including emerging technology sectors such as large-area printed electronics. One technology that has being receiving significant interest in recent years is resistive switching primarily due to its low dimensionality and nonvolatility. Here, we describe the development of resistive switching memory device arrays based on empty aluminum nanogap electrodes. By employing adhesion lithography, a low-temperature and large-area compatible nanogap fabrication technique, dense arrays of memory devices are demonstrated on both rigid and flexible plastic substrates. As-prepared devices exhibit nonvolatile memory operation with stable endurance, resistance ratios >10⁴ and retention times of several months. An intermittent analysis of the electrode microstructure reveals that controlled resistive switching is due to migration of metal from the electrodes into the nanogap under the application of an external electric field. This alternative form of resistive random access memory is promising for use in emerging sectors such as large-area electronics as well as in electronics for harsh environments, e.g., space, high/low temperature, magnetic influences, radiation, vibration, and pressure.

  7. Deep Ultraviolet Copper(I) Thiocyanate (CuSCN) Photodetectors Based on Coplanar Nanogap Electrodes Fabricated via Adhesion Lithography. (United States)

    Wyatt-Moon, Gwenhivir; Georgiadou, Dimitra G; Semple, James; Anthopoulos, Thomas D


    Adhesion lithography (a-Lith) is a versatile fabrication technique used to produce asymmetric coplanar electrodes separated by a <15 nm nanogap. Here, we use a-Lith to fabricate deep ultraviolet (DUV) photodetectors by combining coplanar asymmetric nanogap electrode architectures (Au/Al) with solution-processable wide-band-gap (3.5-3.9 eV) p-type semiconductor copper(I) thiocyanate (CuSCN). Because of the device's unique architecture, the detectors exhibit high responsivity (≈79 A W -1 ) and photosensitivity (≈720) when illuminated with a DUV-range (λ peak = 280 nm) light-emitting diode at 220 μW cm -2 . Interestingly, the photosensitivity of the photodetectors remains fairly high (≈7) even at illuminating intensities down to 0.2 μW cm -2 . The scalability of the a-Lith process combined with the unique properties of CuSCN paves the way to new forms of inexpensive, yet high-performance, photodetectors that can be manufactured on arbitrary substrate materials including plastic.

  8. Deep Ultraviolet Copper(I) Thiocyanate (CuSCN) Photodetectors Based on Coplanar Nanogap Electrodes Fabricated via Adhesion Lithography

    KAUST Repository

    Wyatt-Moon, Gwenhivir


    Adhesion lithography (a-Lith) is a versatile fabrication technique used to produce asymmetric coplanar electrodes separated by a <15 nm nanogap. Here, we use a-Lith to fabricate deep ultraviolet (DUV) photodetectors by combining coplanar asymmetric nanogap electrode architectures (Au/Al) with solution-processable wide-band-gap (3.5–3.9 eV) p-type semiconductor copper(I) thiocyanate (CuSCN). Because of the device’s unique architecture, the detectors exhibit high responsivity (≈79 A W–1) and photosensitivity (≈720) when illuminated with a DUV-range (λpeak = 280 nm) light-emitting diode at 220 μW cm–2. Interestingly, the photosensitivity of the photodetectors remains fairly high (≈7) even at illuminating intensities down to 0.2 μW cm–2. The scalability of the a-Lith process combined with the unique properties of CuSCN paves the way to new forms of inexpensive, yet high-performance, photodetectors that can be manufactured on arbitrary substrate materials including plastic.

  9. Gas sensing performance at room temperature of nanogap interdigitated electrodes for detection of acetone at low concentration

    NARCIS (Netherlands)

    Minh, Q. Nguyen; Tong, H.D.; Kuijk, A.; van de Bent, F.; Beekman, Pepijn; Van Rijn, C. J.M.


    A facile approach for the fabrication of large-scale interdigitated nanogap electrodes (nanogap IDEs) with a controllable gap was demonstrated with conventional micro-fabrication technology to develop chemocapacitors for gas sensing applications. In this work, interdigitated nanogap electrodes

  10. Nanogap structures for molecular nanoelectronics. (United States)

    Motto, Paolo; Dimonte, Alice; Rattalino, Ismael; Demarchi, Danilo; Piccinini, Gianluca; Civera, Pierluigi


    This study is focused on the realization of nanodevices for nano and molecular electronics, based on molecular interactions in a metal-molecule-metal (M-M-M) structure. In an M-M-M system, the electronic function is a property of the structure and can be characterized through I/V measurements. The contact between the metals and the molecule was obtained by gold nanogaps (with a dimension of less than 10 nm), produced with the electromigration technique. The nanogap fabrication was controlled by a custom hardware and the related software system. The studies were carried out through experiments and simulations of organic molecules, in particular oligothiophenes.

  11. Directly Addressable Sub-3 nm Gold Nanogaps Fabricated by Nanoskiving Using Self-Assembled Monolayers as Templates

    NARCIS (Netherlands)

    Pourhossein, Parisa; Chiechi, Ryan C.

    This paper describes the fabrication of electrically addressable, high-aspect-ratio (>10000:1) nanowires of gold with square cross sections of 100 nm on each side that are separated by gaps of 1.7-2.2 nm which were defined using self-assembled monolayers (SAMs) as templates. We fabricated these

  12. Clean electromigrated nanogaps imaged by transmission electron microscopy. (United States)

    Strachan, Douglas R; Smith, Deirdre E; Fischbein, Michael D; Johnston, Danvers E; Guiton, Beth S; Drndić, Marija; Bonnell, Dawn A; Johnson, Alan T


    Electromigrated nanogaps have shown great promise for use in molecular scale electronics. We have fabricated nanogaps on free-standing transparent SiN(x) membranes which permit the use of transmission electron microscopy (TEM) to image the gaps. The electrodes are formed by extending a recently developed controlled electromigration procedure and yield a nanogap with approximately 5 nm separation clear of any apparent debris. The gaps are stable, on the order of hours as measured by TEM, but over time (months) relax to about 20 nm separation determined by the surface energy of the Au electrodes. A major benefit of electromigrated nanogaps on SiN(x) membranes is that the junction pinches in away from residual metal left from the Au deposition which could act as a parasitic conductance path. This work has implications to the design of clean metallic electrodes for use in nanoscale devices where the precise geometry of the electrode is important.

  13. Investigation of electromigration induced by field emission current flowing through Au nanogaps in ambient air (United States)

    Inoue, Kazuki; Yagi, Mamiko; Ito, Mitsuki; Ito, Tomoyuki; Shirakashi, Jun-ichi


    We developed a simple and controllable nanogap fabrication method called "activation." In the activation technique, electromigration is induced by a field emission current passing through the nanogaps. Activation enables the electrical properties of Ni nanogaps in a vacuum to be controlled and is expected to be applicable to Au nanogaps even in ambient air. In this study, we investigated the activation properties of Au nanogaps in ambient air from a practical point of view. When activation was performed in ambient air, the tunnel resistance of the Au nanogaps decreased from over 100 TΩ to 3.7 MΩ as the preset current increased from 1 nA to 1.5 μA. Moreover, after activation in ambient air with a preset current of 500 nA, the barrier widths and heights of the Au nanogaps were estimated using the Simmons model to be approximately 0.5 nm and 3.3 eV, respectively. The extracted barrier height is smaller than that of 4.6 eV resulting from activation in a vacuum and much lower than the work function of bulk Au. This difference implies the presence of atmospherically derived moisture or contamination adsorbed on the nanogaps. These results suggest that activation can be utilized for Au nanogap fabrication even in ambient air.

  14. Tunable nanogap devices for ultra-sensitive electrochemical impedance biosensing

    Energy Technology Data Exchange (ETDEWEB)

    Lu, Yong [Department of Chemistry, Wannan Medical College, Wuhu 241002 (China); Guo, Zheng [Nanomaterials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Song, Jing-Jing; Huang, Qin-An; Zhu, Si-Wei [Department of Chemistry, Wannan Medical College, Wuhu 241002 (China); Huang, Xing-Jiu [Nanomaterials and Environmental Detection Laboratory, Institute of Intelligent Machines, Chinese Academy of Sciences, Hefei 230031 (China); Wei, Yan, E-mail: [Department of Chemistry, Wannan Medical College, Wuhu 241002 (China)


    A wealth of research has been available discussing nanogap devices for detecting very small quantities of biomolecules by observing their electrical behavior generally performed in dry conditions. We report that a gold nanogapped electrode with tunable gap length for ultra-sensitive detection of streptavidin based on electrochemical impedance technique. The gold nanogap is fabricated using simple monolayer film deposition and in-situ growth of gold nanoparticles in a traditional interdigitated array (IDA) microelectrode. The electrochemical impedance biosensor with a 25-nm nanogap is found to be ultra-sensitive to the specific binding of streptavidin to biotin. The binding of the streptavidin hinder the electron transfer between two electrodes, resulting in a large increase in electron-transfer resistance (R{sub et}) for operating the impedance. A linear relation between the relative R{sub et} and the logarithmic value of streptavidin concentration is observed in the concentration range from 1 pM (picomolar) to 100 nM (nanomolar). The lowest detectable concentration actually measured reaches 1 pM. We believe that such an electrochemical impedance nanogap biosensor provides a useful approach towards biomolecular detection that could be extended to a number of other systems. - Highlights: • A tunable gold nanogap device was used as to electrochemical impedance biosensor. • Linear range from 1 pM to 100 nM with LOD of 1 pM for streptavidin detection was obtained. • The nanogap devices exhibit a satisfactory precision, stability, and reproducibility. • The combination of electrochemical impedance technique and nanogap devices was achieved.

  15. Single-Molecule Detection in Nanogap-Embedded Plasmonic Gratings

    Directory of Open Access Journals (Sweden)

    Biyan Chen


    Full Text Available We introduce nanogap-embedded silver plasmonic gratings for single-molecule (SM visualization using an epifluorescence microscope. This silver plasmonic platform was fabricated by a cost-effective nano-imprint lithography technique, using an HD DVD template. DNA/ RNA duplex molecules tagged with Cy3/Cy5 fluorophores were immobilized on SiO 2 -capped silver gratings. Light was coupled to the gratings at particular wavelengths and incident angles to form surface plasmons. The SM fluorescence intensity of the fluorophores at the nanogaps showed approximately a 100-fold mean enhancement with respect to the fluorophores observed on quartz slides using an epifluorescence microscope. This high level of enhancement was due to the concentration of surface plasmons at the nanogaps. When nanogaps imaged with epifluorescence mode were compared to quartz imaged using total internal reflection fluorescence (TIRF microscopy, more than a 30-fold mean enhancement was obtained. Due to the SM fluorescence enhancement of plasmonic gratings and the correspondingly high emission intensity, the required laser power can be reduced, resulting in a prolonged detection time prior to photobleaching. This simple platform was able to perform SM studies with a low-cost epifluorescence apparatus, instead of the more expensive TIRF or confocal microscopes, which would enable SM analysis to take place in most scientific laboratories.

  16. Growth of segmented gold nanorods with nanogaps by the electrochemical wet etching technique for single-electron transistor applications (United States)

    Hoang, Nguyen Van; Kumar, Sanjeev; Kim, Gil-Ho


    The growth of multisegment nanorods comprising gold (Au) and sacrificial silver (Ag) segments (Au-Ag-Au or Au-Ag-Au-Ag-Au) using the electrochemical wet etching method is reported. The nanorods were fabricated using an alumina template of thickness 100 µm and pore size of 200 nm. A variety of nanorods from single to seven segments comprising alternate Au and Ag segments were fabricated with better control of growth rate. The multisegment nanorods were selectively etched by removing the Ag segments to create gaps in the fabricated nanorods. A careful investigation led to the creation of a wide variety of nanogaps in the fabricated multisegment nanorods. The size of the nanogap was controlled by the passage of current through the electrochemical process, and size below 10 nm was achievable at exchanged charges of ~1 mC. A further lowering in the size of nanogaps was achieved by diluting the silver plating solution and a segmented nanorod with nanogap (Au-nanogap-Au) of 3.8 nm at exchanged charges of 0.2 mC was successfully created. In addition, segmented nanorods with two or more nanogaps (Au-nanogap-Au-nanogap-Ag) placed symmetrically and asymmetrically on either side of the central Au segments were also created. A prototype of a single-electron transistor device based on segmented nanorods with two nanogaps is proposed. The results obtained could form the basis for the realization of quantum tunneling devices where the barrier thickness is very critical and demands values less than 5 nm. The encouraging results show the promise of multisegment nanorods for fabricating devices working at the de Broglie wavelength such as single-electron transistors.

  17. Dielectrophoretic Trapping of Au Nanoparticles using High Quality Nanogap Electrodes (United States)

    Lu, Ye; Johnston, Danvers E.; Strachan, Douglas R.; Guiton, Beth S.; Davies, Peter K.; Park, Tae-Hong; Therien, Michael J.; Johnson, A. T. Charlie


    In the past decade, single molecule-based electronic devices have drawn enormous attention. One of the great challenges to be overcome is the fabrication of well-defined, uncontaminated nanogap electrodes, and the subsequent assembly of individual molecules or nanoparticles onto the contacts. A promising route to this goal is the feedback controlled electromigration (FCE) process, which can be used to create stable, metal-particle free nanogap contacts at temperatures ranging from 4--300 K.^1,2 Here we describe experiments where Au nanoparticles (NPs) are assembled inside FCE fabricated nanogaps by using positive AC dielectrophoresis (DEP). Specific challenges relating to circuit design for efficient DEP and solutions to these challenges are discussed. Additionally, substrate interactions are found to substantially influence dielectrophoretic assembly. Methods for controlling DEP assembly by modification of the electrostatic interaction between NPs and substrate surfaces are explored. Funding: NSF-NSEC/NBIC DMR-0425780. ^1 D. R. Strachan et al., Appl. Phys. Lett. 86 043109 (2005). ^2 D. R. Strachan et al., Nano. Lett. 86 043109 (2006).

  18. Controlled electroplating and electromigration in nickel electrodes for nanogap formation

    Energy Technology Data Exchange (ETDEWEB)

    De Los Santos Valladares, Luis; Mitrelias, Thanos; Sfigakis, Francois; Barnes, Crispin H W [Cavendish Laboratory, University of Cambridge, J J Thomson Avenue, Cambridge CB3 0HE (United Kingdom); Leon Felix, Lizbet; Bustamante Dominguez, Angel [Laboratorio de Ceramicos y Nanomateriales, Universidad Nacional Mayor de San Marcos, Ap. Postal 14-0149, Lima (Peru); Khondaker, Saiful I [NanoScience Technology Center and Department of Physics, University of Central Florida, Orlando, FL 32826 (United States); Majima, Yutaka, E-mail:, E-mail: [Materials and Structures Laboratory, Tokyo Institute of Technology, 4259 Nagatsuta-cho, Midori-ku, Yokohama 226-8503 (Japan)


    We report the fabrication of nickel nanospaced electrodes by electroplating and electromigration for nanoelectronic devices. Using a conventional electrochemical cell, nanogaps can be obtained by controlling the plating time alone and after a careful optimization of electrodeposition parameters such as electrolyte bath, applied potential, cleaning, etc. During the process, the gap width decreases exponentially with time until the electrode gaps are completely bridged. Once the bridge is formed, the ex situ electromigration technique can reopen the nanogap. When the gap is {approx} 1 nm, tunneling current-voltage characterization shows asymmetry which can be corrected by an external magnetic field. This suggests that charge transfer in the nickel electrodes depends on the orientation of magnetic moments.

  19. Wet chemical synthesis of soluble gold nanogaps

    DEFF Research Database (Denmark)

    Jain, Titoo; Tang, Qingxin; Bjørnholm, Thomas


    in the nanogaps lets us spectroscopically characterize the molecules via surface-enhanced Raman scattering. We discuss the incorporation of oligopeptides functionalized with acetylene units having uniquely identifiable vibrational modes. This acetylene moiety allows chemical reactions to be performed in the gaps...... via click chemistry, and the oligopeptide linking platform opens for integration of larger biological components....

  20. Self-assembled nanogaps for molecular electronics

    DEFF Research Database (Denmark)

    Tang, Qingxin; Tong, Yanhong; Jain, Titoo


    A nanogap for molecular devices was realized using solution-based self-assembly. Gold nanorods were assembled to gold nanoparticle-coated conducting SnO2:Sb nanowires via thiol end-capped oligo(phenylenevinylene)s (OPVs). The molecular gap was easily created by the rigid molecule itself during self...

  1. Silicon based nanogap device for investigating electronic transport through 12 nm long oligomers

    DEFF Research Database (Denmark)

    Strobel, S.; Albert, E.; Csaba, G.


    We have fabricated vertical nanogap electrode devices based on Silicon-on-Insulator (SOI) substrates for investigating the electronic transport properties of long, conjugated molecular wires. Our nanogap electrode devices comprise smooth metallic contact pairs situated at the sidewall of an SOI...... structure, obtained by selective recess-etching a few nanometers thin buried oxide layer and subsequent thin film metallization. The electrodes are separated by a predetermined distance down to about 5 nm and feature a well-tailored material layer structure, as characterized by SEM and scanning TEM analysis....... We studied the electronic transport properties of 12 nm long, specifically synthesized dithiolated oligo-phenylene-vinylene derivatives assembled onto the electrode gap from solution. In particular, we observed a pronounced, non-linear current-voltage characteristic featuring a large conductance gap...

  2. Realization of size controllable graphene micro/nanogap with a micro/nanowire mask method for organic field-effect transistors

    DEFF Research Database (Denmark)

    Liao, Zhiyu; Wan, Qing; Liu, Huixuan


    with the graphene micro/nanogap bottom electrodes. The ultrathin thickness of the graphene, combined with its good compatibility with organic semiconductors, and high electrical conductivity produced high-performance CuPc film device with mobility at 0.053 cm(2)/Vs and on/off ratio at 10(5), showing promising......A size controllable graphene micro/nanogap fabrication method using micro/nanowire as mask is presented. The gap dimension can be adjusted by the diameter of the mask wire. As a typical application, copper phthalocyanine (CuPc) film organic field-effect transistors (OFETs) were fabricated...

  3. On the high charge-carrier mobility in polyaniline molecular channels in nanogaps between carbon nanotubes

    Energy Technology Data Exchange (ETDEWEB)

    Emelianov, A. V., E-mail:; Romashkin, A. V.; Tsarik, K. A. [National Research University of Electronic Technology (MIET) (Russian Federation); Nasibulin, A. G. [Skolkovo Institute of Science and Technology (Russian Federation); Nevolin, V. K.; Bobrinetskiy, I. I. [National Research University of Electronic Technology (MIET) (Russian Federation)


    This study is devoted to the fabrication of molecular semiconductor channels based on polymer molecules with nanoscale electrodes made of single-walled carbon nanotubes. A reproducible technology for forming nanoscale gaps in carbon nanotubes using a focused Ga{sup +} ion beam is proposed. Polyaniline molecules are deposited into nanogaps up to 30 nm wide between nanotubes by electrophoresis from N-methyl-2-pyrrolidone solution. As a result, molecular organic transistors are fabricated, in which the field effect is studied and the molecular-channel mobility is determined as 0.1 cm{sup 2}/(V s) at an on/off current ratio of 5 × 10{sup 2}.

  4. Development of optimized nanogap plasmonic substrate for improved SERS enhancement

    Directory of Open Access Journals (Sweden)

    Jayakumar Perumal


    Full Text Available SERS enhancement factor (EF of planar substrates depends on the size and shape of the fine nanostructure forming a defect free, well-arranged matrix. Nano-lithographic process is considered to be the most advanced methods employed for the fabrication SERS substrates. Nanostructured plasmonic substrates with nanogap (NG pattern often results in stable, efficient and reproducible SERS enhancement. For such substrates, NG and their diagonal length (DL need to be optimized. Theoretically smaller NGs (∼30-40 nm or smaller results in higher SERS enhancement. However, fabrication of NG substrates below such limit is a challenge even for the most advanced lithography process. In this context, herein, we report the optimization of fabrication process, where higher SERS enhancement can be realized from larger NGs substrates by optimizing their DL of nanostructures between the NGs. Based on simulation we could demonstrate that, by optimizing the DL, SERS enhancement from larger NG substrate such as 60 and 80 nm could be comparable to that of smaller (40nm NG substrates. We envision that this concept will open up new regime in the nanofabrication of practically feasible NG based plasmonic substrates with higher SERS enhancement. Initial results of our experiments are in close agreement with our simulated study.

  5. Anomalous extinction in index-matched terahertz nanogaps (United States)

    Jeong, Jeeyoon; Kim, Dasom; Park, Hyeong-Ryeol; Kang, Taehee; Lee, Dukhyung; Kim, Sunghwan; Bahk, Young-Mi; Kim, Dai-Sik


    Slot-type nanogaps have been widely utilized in transmission geometry because of their advantages of exclusive light funneling and exact quantification of near-field enhancement at the gap. For further application of the nanogaps in electromagnetic interactions with various target materials, complementary studies on both transmission and reflection properties of the nanogaps are necessary. Here, we observe an anomalous extinction of terahertz waves interacting with rectangular ring-shaped sub-30 nm wide gaps. Substrate works as an index matching layer for the nanogaps, leading to a stronger field enhancement and increased nonlinearity at the gap under substrate-side illumination. This effect is expressed in reflection as a larger dip at the resonance, caused by destructive interference of the diffracted field from the gap with the reflected beam from the metal. The resulting extinction at the resonance is larger than 60% of the incident power, even without any absorbing material in the whole nanogap structure. The extinction even decreases in the presence of an absorbing medium on top of the nanogaps, suggesting that transmission and reflection from nanogaps might not necessarily represent the absorption of the whole structure.

  6. Plasmonic Nanogap-Enhanced Raman Scattering with Nanoparticles. (United States)

    Nam, Jwa-Min; Oh, Jeong-Wook; Lee, Haemi; Suh, Yung Doug


    Plasmonic coupling-based electromagnetic field localization and enhancement are becoming increasingly important in chemistry, nanoscience, materials science, physics, and engineering over the past decade, generating a number of new concepts and applications. Among the plasmonically coupled nanostructures, metal nanostructures with nanogaps have been of special interest due to their ultrastrong electromagnetic fields and controllable optical properties that can be useful for a variety of signal enhancements such as surface-enhanced Raman scattering (SERS). The Raman scattering process is highly inefficient, with a very small cross-section, and Raman signals are often poorly reproducible, meaning that very strong, controllable SERS is needed to obtain reliable Raman signals with metallic nanostructures and thus open up new avenues for a variety of Raman-based applications. More specifically, plasmonically coupled metallic nanostructures with ultrasmall (∼1 nm or smaller) nanogaps can generate very strong and tunable electromagnetic fields that can generate strong SERS signals from Raman dyes in the gap, and plasmonic nanogap-enhanced Raman scattering can be defined as Raman signal enhancement from plasmonic nanogap particles with ∼1 nm gaps. However, these promising nanostructures with extraordinarily strong optical signals have shown limited use for practical applications, largely due to the lack of design principles, high-yield synthetic strategies with nanometer-level structural control and reproducibility, and systematic, reliable single-molecule/single-particle-level studies on their optical properties. All these are extremely important challenges because even small changes (plasmonic nanogaps can significantly affect the plasmon mode and signal intensity. In this Account, we examine and summarize recent breakthroughs and advances in plasmonic nanogap-enhanced Raman scattering with metal nanogap particles with respect to the design and synthesis of plasmonic

  7. Nanogap Electrodes towards Solid State Single-Molecule Transistors. (United States)

    Cui, Ajuan; Dong, Huanli; Hu, Wenping


    With the establishment of complementary metal-oxide-semiconductor (CMOS)-based integrated circuit technology, it has become more difficult to follow Moore's law to further downscale the size of electronic components. Devices based on various nanostructures were constructed to continue the trend in the minimization of electronics, and molecular devices are among the most promising candidates. Compared with other candidates, molecular devices show unique superiorities, and intensive studies on molecular devices have been carried out both experimentally and theoretically at the present time. Compared to two-terminal molecular devices, three-terminal devices, namely single-molecule transistors, show unique advantages both in fundamental research and application and are considered to be an essential part of integrated circuits based on molecular devices. However, it is very difficult to construct them using the traditional microfabrication techniques directly, thus new fabrication strategies are developed. This review aims to provide an exclusive way of manufacturing solid state gated nanogap electrodes, the foundation of constructing transistors of single or a few molecules. Such single-molecule transistors have the potential to be used to build integrated circuits. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Nanogap dielectric spectroscopy for aptamer-based protein detection. (United States)

    Mannoor, Manu Sebastian; James, Teena; Ivanov, Dentcho V; Beadling, Les; Braunlin, William


    Among the various label-free methods for monitoring biomolecular interactions, capacitive sensors stand out due to their simple instrumentation and compatibility with multiplex formats. However, electrode polarization due to ion gradient formation and noise from solution conductance limited early dielectric spectroscopic measurements to high frequencies only, which in turn limited their sensitivity to biomolecular interactions, as the applied excitation signals were too fast for the charged macromolecules to respond. To minimize electrode polarization effects, capacitive sensors with 20 nm electrode separation were fabricated using silicon dioxide sacrificial layer techniques. The nanoscale separation of the capacitive electrodes in the sensor results in an enhanced overlapping of electrical double layers, and apparently a more ordered "ice-like" water structure. Such effects in turn reduce low frequency contributions from bulk sample resistance and from electrode polarization, and thus markedly enhance sensitivity toward biomolecular interactions. Using these nanogap capacitive sensors, highly sensitive, label-free aptamer-based detection of protein molecules is achieved. Copyright 2010 Biophysical Society. Published by Elsevier Inc. All rights reserved.

  9. Plasmon-Driven Dynamic Response of a Hierarchically Structural Silver-Decorated Nanorod Array for Sub-10 nm Nanogaps. (United States)

    Wang, Yi; Wang, Hailong; Wang, Yuyang; Shen, Yanting; Xu, Shuping; Xu, Weiqing


    Plasmonic nanogaps serve as a useful configuration for light concentration and local field amplification owing to the extreme localization of surface plasmons. Here, a smart plasmonic nanogap device is fabricated by the dynamic response of an Ag decorated hierarchically structural vertical polymer nanorod array under the light irradiation. Seven nanorods in one unit bend because of plasmonic heating effect and they are centrally collected due to the attraction of the plasmon-induced polaritons, leading to the significantly enhanced local electromagnetic field at the sub-10 nm gaps among the constricted nanorod tops. Compared with tuning capillarity in microscale by wetting and drying, using light as external stimuli is much easier and more tunable in nanoscale. This plasmonic nanogap device is used for a surface-enhanced Raman scattering (SERS) substrate. Its hydrophobic surface with a contact angle of 142 degree can make the probed aqueous solution only access to the Ag tips of nanorods. Thus, the analytes can be driven to the "hot spot" regions where located at the tops of nanorods during the solvent evaporation process, which is beneficial to SERS detection. Discovery of this smart plasmon-driven process broadens the scope for further functionality of both the dynamic nanostructure design and the smart plasmonic devices in the communities of chemistry, biomedicine, and microfluidic engineering.

  10. Non-radiative and radiative decays in nanogap emitting devices

    CERN Document Server

    Faggiani, Remi; Lalanne, Philippe


    By placing a quantum emitter in the mouths of nanogaps consisting of two metal nanoparticles nearly into contact, significant increases in emission rate are obtained. This mechanism is central in the design of modern plasmonic nanoantennas. However, due to the lack of general knowledge on the balance between the different decay rates in nanogaps (emission, quenching, and metal absorption), nanoantenna design is performed in a rather haphazard fashion and relies on repeated numerical calculations; general intuitive design recipes do not presently exist. With accurate and simple closed-form expressions for the quenching rate and the decay rate into gap plasmons, we provide a comprehensive analysis of nanogap light emitting devices in the limit of small gap thickness. We disclose that the total spontaneous emission rate of quantum emitters in nanometer-thin gaps can largely overcome quenching, for specifically selected metallic and insulator materials, regardless of the gap size. Furthermore, to help further des...

  11. Nanogap based graphene coated AFM tips with high spatial resolution, conductivity and durability. (United States)

    Lanza, Mario; Gao, Teng; Yin, Zixuan; Zhang, Yanfeng; Liu, Zhongfan; Tong, Yuzhen; Shen, Ziyong; Duan, Huiling


    After one decade of analyzing the intrinsic properties of graphene, interest into the development of graphene-based devices and micro electromechanical systems is increasing. Here, we fabricate graphene-coated atomic force microscope tips by growing the graphene on copper foil and transferring it onto the apex of a commercially available AFM tip. The resulting tip exhibits surprising enhanced resolution in nanoscale electrical measurements. By means of topographic AFM maps and statistical analyses we determine that this superior performance may be related to the presence of a nanogap between the graphene and the tip apex, which reduces the tip radius and tip-sample contact area. In addition, the graphene-coated tips show a low tip-sample interaction, high conductivity and long life times. The novel fabrication-friendly tip could improve the quality and reliability of AFM experiments, while reducing the cost of AFM-based research.

  12. Electrical breakdown and nanogap formation of indium oxide core/shell heterostructure nanowires. (United States)

    Jung, Minkyung; Song, Woon; Sung Lee, Joon; Kim, Nam; Kim, Jinhee; Park, Jeunghee; Lee, Hyoyoung; Hirakawa, Kazuhiko


    We report the electrical breakdown behavior and subsequent nanogap formation of In(2)O(3)/InO(x) core/shell heterostructure nanowires with substrate-supported and suspended structures. The radial heterostructure nanowires, composed of crystalline In(2)O(3) cores and amorphous In-rich shells, are grown by chemical vapor deposition. As the nanowires broke down, they exhibited two distinct current drops in the current-voltage characteristics. The tips of the broken nanowires were found to have a cone or a volcano shape depending on the width of the nanowire. The shape, the size, and the position of the nanogap depend strongly on the device structure and the nanowire dimensions. The substrate-supported and the suspended devices exhibit distinct breakdown behavior which can be explained by the diffusive thermal transport model. The breakdown temperature of the nanowire is estimated to be about 450 K, close to the melting temperature of indium. We demonstrated the usefulness of this technique by successful fabrication of working pentacene field-effect transistors.

  13. Atomic layer lithography of wafer-scale nanogap arrays for extreme confinement of electromagnetic waves. (United States)

    Chen, Xiaoshu; Park, Hyeong-Ryeol; Pelton, Matthew; Piao, Xianji; Lindquist, Nathan C; Im, Hyungsoon; Kim, Yun Jung; Ahn, Jae Sung; Ahn, Kwang Jun; Park, Namkyoo; Kim, Dai-Sik; Oh, Sang-Hyun


    Squeezing light through nanometre-wide gaps in metals can lead to extreme field enhancements, nonlocal electromagnetic effects and light-induced electron tunnelling. This intriguing regime, however, has not been readily accessible to experimentalists because of the lack of reliable technology to fabricate uniform nanogaps with atomic-scale resolution and high throughput. Here we introduce a new patterning technology based on atomic layer deposition and simple adhesive-tape-based planarization. Using this method, we create vertically oriented gaps in opaque metal films along the entire contour of a millimetre-sized pattern, with gap widths as narrow as 9.9 Å, and pack 150,000 such devices on a 4-inch wafer. Electromagnetic waves pass exclusively through the nanogaps, enabling background-free transmission measurements. We observe resonant transmission of near-infrared waves through 1.1-nm-wide gaps (λ/1,295) and measure an effective refractive index of 17.8. We also observe resonant transmission of millimetre waves through 1.1-nm-wide gaps (λ/4,000,000) and infer an unprecedented field enhancement factor of 25,000.

  14. Subwavelength metal nanogap surface for surface-enhanced Raman spectroscopy

    NARCIS (Netherlands)

    Le Thi Ngoc, Loan


    In this dissertation, a new top-down nanofabrication echnology is presented to realize large area metal nanowire rrays with tunable sub-20 nm separation nanogaps without the use of chemical etching or milling of the metal layer. Gold and silver nanowire arrays are presented with high-density on the

  15. Live cell imaging using Au-NNP (Nanobridged Nanogap Particles) (Presentation Recording) (United States)

    Suh, Yung Doug


    Single-particle tracking Live-Cell imaging using Au-NNP(Nanobridged Nanogap Particles) will be presented. Due to a stable plasmonic amplification of Raman signal from the intra-nanogap of Au-NNP, we have a stable and strong Raman signal enough for single particle imaging of Au-NNP in live cell. Multiplex imaging by encoding different Raman dyes into this nanogap and its application will be also discussed.

  16. Creation of a transient vapor nanogap between two fluidic reservoirs for single molecule manipulation. (United States)

    Polonsky, Stanislav; Balagurusamy, Venkat S K; Ott, John A


    We introduce a new experimental technique for manipulating a segment of a charged macromolecule inside a transient nanogap between two fluidic reservoirs. This technique uses an FPGA-driven nanopositioner to control the coupling of a nanopipette with the liquid surface of a fluidic cell. We present results on creating a transient nanogap, triggered by a translocation of double-stranded DNA between a nanopipette and a fluidic cell, and measure the probability to find the molecule near the tip of the nanopipette after closing the gap. The developed platform will enable testing of our recent theoretical predictions for the behavior of charged macromolecule in a nanogap between two fluidic reservoirs.

  17. Creation of a transient vapor nanogap between two fluidic reservoirs for single molecule manipulation (United States)

    Polonsky, Stanislav; Balagurusamy, Venkat S. K.; Ott, John A.


    We introduce a new experimental technique for manipulating a segment of a charged macromolecule inside a transient nanogap between two fluidic reservoirs. This technique uses an FPGA-driven nanopositioner to control the coupling of a nanopipette with the liquid surface of a fluidic cell. We present results on creating a transient nanogap, triggered by a translocation of double-stranded DNA between a nanopipette and a fluidic cell, and measure the probability to find the molecule near the tip of the nanopipette after closing the gap. The developed platform will enable testing of our recent theoretical predictions for the behavior of charged macromolecule in a nanogap between two fluidic reservoirs.

  18. Fabrication of Lateral Polysilicon Gap of Less than 50 nm Using Conventional Lithography

    Directory of Open Access Journals (Sweden)

    Th. S. Dhahi


    Full Text Available We report a thermal oxidation process for the fabrication of nanogaps of less than 50 nm in dimension. Nanogaps of this dimension are necessary to eliminate contributions from double-layer capacitance in the dielectric detection of protein or nucleic acid. The method combines conventional photolithography and pattern-size reduction techniques. The gaps are fabricated on polysilicon-coated silicon substrate with gold electrodes. The dimensions of the structure are determined by scanning electron microscopy (SEM. An electrical characterization of the structures by dielectric analyzer (DA shows an improved conductivity as well as enhanced permittivity and capacity with the reduction of gap size, suggesting its potential applications in the detection of biomolecule with very low level of power supply. Two chrome Masks are used to complete the work: the first Mask is for the nanogap pattern and the second one is for the electrodes. An improved resolution of pattern size is obtained by controlling the oxidation time. The method expected to enable fabrication of nanogaps with a wide ranging designs and dimensions on different substrates. It is a simple and cost-effective method and does not require complicated nanolithography process for fabricating desired nanogaps in a reproducible fashion.

  19. Thiolated DNA-based chemistry and control in the structure and optical properties of plasmonic nanoparticles with ultrasmall interior nanogap. (United States)

    Oh, Jeong-Wook; Lim, Dong-Kwon; Kim, Gyeong-Hwan; Suh, Yung Doug; Nam, Jwa-Min


    The design, synthesis and control of plasmonic nanostructures, especially with ultrasmall plasmonically coupled nanogap (∼1 nm or smaller), are of significant interest and importance in chemistry, nanoscience, materials science, optics and nanobiotechnology. Here, we studied and established the thiolated DNA-based synthetic principles and methods in forming and controlling Au core-nanogap-Au shell structures [Au-nanobridged nanogap particles (Au-NNPs)] with various interior nanogap and Au shell structures. We found that differences in the binding affinities and modes among four different bases to Au core, DNA sequence, DNA grafting density and chemical reagents alter Au shell growth mechanism and interior nanogap-forming process on thiolated DNA-modified Au core. Importantly, poly A or poly C sequence creates a wider interior nanogap with a smoother Au shell, while poly T sequence results in a narrower interstitial interior gap with rougher Au shell, and on the basis of the electromagnetic field calculation and experimental results, we unraveled the relationships between the width of the interior plasmonic nanogap, Au shell structure, electromagnetic field and surface-enhanced Raman scattering. These principles and findings shown in this paper offer the fundamental basis for the thiolated DNA-based chemistry in forming and controlling metal nanostructures with ∼1 nm plasmonic gap and insight in the optical properties of the plasmonic NNPs, and these plasmonic nanogap structures are useful as strong and controllable optical signal-generating nanoprobes.

  20. High Quality Nanogap Electrodes for Electronic Transport Measurements of Single Molecules (United States)

    Johnston, Danvers E.; Strachan, Douglas R.; Guiton, Beth S.; Davies, Peter K.; Park, Tae Hong; Therien, Michael J.; Johnson, A. T. Charlie


    Electromigrated metal electrodes and resulting devices have shown great promise in moving towards the realization of single molecule-based electronic devices holding the potential for a wide range of electronic applications. At present, a major concern is that the electronic behavior of such devices may be greatly influenced by residual nanoscale metal particles. We have developed a computer controlled electromigration (CCE) process for creating nanogaps at room temperature which allows us to characterize a bare nanogap before putting a molecule into the nanogap.^1 This is very different from other approaches used in the field where nanogaps are formed at low temperature with molecules already attached to the nanowire by employing a simple ramp up in voltage. Among the bare nanogaps we produced using CCE, tunneling behavior is observed with no indication of transport signatures associated with metal particle formation. Details of molecular measurements utilizing these clean gaps will be discussed. This work was supported by the National Science Foundation (NIRT Grant No. 0304531 and MRSEC award DMR05-20020). ^1D. R. Strachan, D. E. Smith, D. E. Johnston et al., Appl. Phys. Lett. 86 043109 (2005).

  1. Room-temperature gating of molecular junctions using few-layer graphene nanogap electrodes (United States)

    Barreiro, Amelia; Prins, Ferry; Ruitenberg, Justus; Seldenthuis, Johannes; Aliaga-Alcalde, Nuria; Vandersypen, Lieven; van der Zant, Herre


    We report on a new method based on feedback controlled electroburning to controllably form nanogaps in few-layer graphene [1]. The gaps have separations on the order of 1-2 nm as estimated from a Simmons model for tunneling. Furthermore, molecules are deposited in the nanogaps. These molecular junctions display gateable IV-characteristics at room temperature. Gateable transport through molecules contacted between the electrodes demonstrates the potential of room-temperature operation of our molecular devices. Combined with the observed stability in time, our study shows that few-layer graphene nanogaps are an interesting alternative to metal electrodes. [1] Ferry Prins, Amelia Barreiro, Justus Ruitenberg, Johannes Seldenthuis, N'uria Aliaga-Alcalde, Lieven Vandersypen, Herre van der Zant, Nanoletters 11 (2011) 4607 - 4611

  2. Polysilicon nanogap lab-on-chip facilitates multiplex analyses with single analyte. (United States)

    Balakrishnan, Sharma Rao; Hashim, U; Gopinath, Subash C B; Poopalan, P; Ramayya, H R; Veeradasan, P; Haarindraprasad, R; Ruslinda, A R


    Rationally designed biosensing system supports multiplex analyses is warranted for medical diagnosis to determine the level of analyte interaction. The chemically functionalized novel multi-electrode polysilicon nanogap (PSNG) lab-on-chip is designed in this study, facilitates multiplex analyses for a single analyte. On the fabricated 69nm PSNG, biocompatibility and structural characteristics were verified for the efficient binding of Human Chorionic Gonadotropin (hCG). With the assistance of microfluidics, hCG sample was delivered via single-injection to 3-Aminopropyl(triethoxy)silane (APTES) and Glycidoxypropyl(trimethoxy)silane (GPMS) modified PSNG electrodes and the transduced signal was used to investigate the dielectric mechanisms for multiplex analyses. The results from amperometric response and impedance measurement delivered the scale of interaction between anti-hCG antibody and hCG that exhibited 6.5 times higher sensitivity for the chemical linker, APTES than GPMS. Under optimized experimental conditions, APTES and GPMS modified immunosensor has a limit of detection as 0.56mIU/ml and 2.93mIU/ml (at S/N=3), with dissociation constants (Kd) of 5.65±2.5mIU/ml and 7.28±2.6mIU/ml, respectively. These results suggest that multiplex analysis of single target could enhance the accuracy of detection and reliable for real-time comparative analyses. The designed PSNG is simple, feasible, requires low sample consumption and could be applied for any given multiplex analyses. Copyright © 2015 Elsevier B.V. All rights reserved.

  3. Large and well-defined Rabi splitting in a semiconductor nanogap cavity. (United States)

    Uemoto, Mitsuharu; Ajiki, Hiroshi


    We propose a nanogap structure composed of semiconductor nanoparticles forming an optical cavity. The resonant excitation of excitons in the nanoparticles can generate a localized strong light field in the gap region, also called "hot spot". The spectral width of the hot spot is significantly narrow because of the small exciton damping and the dephasing at low temperature, so the semiconductor nanogap structure acts as a high-Q cavity. In addition, the interaction between light and matter at the nanogap is significantly larger than that in a conventional microcavity, because the former has a small cavity-mode volume beyond the diffraction limit. We theoretically demonstrate the large and well-defined vacuum-Rabi splitting of a two-level emitter placed inside the semiconductor nanogap cavity: the Rabi splitting energy of 1.7 meV for the transition dipole moment of the emitter (25 Debye) is about 6.3 times larger than the spectral width. An optical cavity providing such a large and well-defined Rabi splitting is highly suited for studying characteristic features of the cavity quantum electrodynamics and for the development of new applications.

  4. In situ imaging of electromigration-induced nanogap formation by transmission electron microscopy

    NARCIS (Netherlands)

    Heersche, H.B.; Lientschnig, G.; O'Neill, K.; Van der Zant, H.S.J.; Zandbergen, H.W.


    The authors imaged electromigration-induced nanogap formation in situ by transmission electron microscopy. Real-time video recordings show that edge voids form near the cathode side. The polycrystalline gold wires narrow down until a single-grain boundary intersects the constriction along which the

  5. Controlled Fabrication and High-Resolution Imaging of Molecular-Scale Three-Terminal Devices (United States)

    Strachan, Douglas R.; Johnston, Danvers E.; Guiton, Beth S.; Park, T.-H.; Therien, M. J.; Davies, Peter K.; Bonnell, Dawn A.; Johnson, A. T. Charlie


    One of the biggest challenges to developing molecular-scale three terminal devices is to precisely fabricate and monitor the formation of the nanometer-scale electrodes (nanogaps). Recently, electromigrated nanogaps have been developed which provide sufficient gate-coupling to produce such devices. We have developed a technique for forming electromigrated nanogaps in a transmission electron microscope (TEM) in order to monitor their formation with high-resolution imaging in real time. The technique relies on computer-controlled electromigration using feedback to produce the nanogaps at room temperature. This TEM imaging allows us to monitor the dynamics of the device evolution, where the gaps remain ordered and clear of residue during the process. Using this technique, we find clear visual evidence for the importance of joule heating in the formation of electromigrated nanogaps. These electrodes can also be directly used in the construction of three terminal nanometer-scale devices. Our results have implications on the development of a wide range of novel molecular-scale devices. This work was supported by the National Science Foundation (NIRT Grant No. 0304531 and MRSEC award DMR05-20020).

  6. Resonant Cavity Enhanced On-Chip Raman Spectrometer Array with Precisely Positioned Metallic Nano-Gaps for Single Molecule Detection (United States)


    REPORT Resonant Cavity Enhanced On-Chip Raman Spectrometer Array with Precisely Positioned Metallic Nano-Gaps for Single Molecule Detection 14...with Precisely Positioned Metallic Nano-Gaps for Single Molecule Detection Report Title ABSTRACT During the Phase I program, our theoretical and...size is below 5 nano-meter (nm). Early single molecule SERS experiments are done typically with aggregates of colloidal nanoparticles where the “hot

  7. Aviram-Ratner rectifying mechanism for DNA base-pair sequencing through graphene nanogaps (United States)

    Agapito, Luis A.; Gayles, Jacob; Wolowiec, Christian; Kioussis, Nicholas


    We demonstrate that biological molecules such as Watson-Crick DNA base pairs can behave as biological Aviram-Ratner electrical rectifiers because of the spatial separation and weak hydrogen bonding between the nucleobases. We have performed a parallel computational implementation of the ab initio non-equilibrium Green’s function (NEGF) theory to determine the electrical response of graphene—base-pair—graphene junctions. The results show an asymmetric (rectifying) current-voltage response for the cytosine-guanine base pair adsorbed on a graphene nanogap. In sharp contrast we find a symmetric response for the thymine-adenine case. We propose applying the asymmetry of the current-voltage response as a sensing criterion to the technological challenge of rapid DNA sequencing via graphene nanogaps.

  8. A Point-of-Care Immunosensor for Human Chorionic Gonadotropin in Clinical Urine Samples Using a Cuneated Polysilicon Nanogap Lab-on-Chip.

    Directory of Open Access Journals (Sweden)

    S R Balakrishnan

    Full Text Available Human chorionic gonadotropin (hCG, a glycoprotein hormone secreted from the placenta, is a key molecule that indicates pregnancy. Here, we have designed a cost-effective, label-free, in situ point-of-care (POC immunosensor to estimate hCG using a cuneated 25 nm polysilicon nanogap electrode. A tiny chip with the dimensions of 20.5 × 12.5 mm was fabricated using conventional lithography and size expansion techniques. Furthermore, the sensing surface was functionalized by (3-aminopropyltriethoxysilane and quantitatively measured the variations in hCG levels from clinically obtained human urine samples. The dielectric properties of the present sensor are shown with a capacitance above 40 nF for samples from pregnant women; it was lower with samples from non-pregnant women. Furthermore, it has been proven that our sensor has a wide linear range of detection, as a sensitivity of 835.88 μA mIU(-1 ml(-2 cm(-2 was attained, and the detection limit was 0.28 mIU/ml (27.78 pg/ml. The dissociation constant Kd of the specific antigen binding to the anti-hCG was calculated as 2.23 ± 0.66 mIU, and the maximum number of binding sites per antigen was Bmax = 22.54 ± 1.46 mIU. The sensing system shown here, with a narrow nanogap, is suitable for high-throughput POC diagnosis, and a single injection can obtain triplicate data or parallel analyses of different targets.

  9. Semiconducting III-V nanowires with nanogaps for molecular junctions: DFT transport simulations

    DEFF Research Database (Denmark)

    Kallesøe, Christian; Fürst, Joachim Alexander; Mølhave, Kristian


    We consider here the possibility of using III–V heterostructure nanowires as electrodes for molecular electronics instead of metal point contacts. Using ab initio electronic structure and transport calculations, we study the effect on electronic properties of placing a small molecule with thiol...... linking groups, benzene-di-thiol (BDT), within a nanosize gap in a III–V nanowire. Furthermore, it is investigated how surface states affect the transport through pristine III–V nanowires and through the BDT molecule situated within the nanogap. Using GaAs and GaP as III–V materials we find that the BDT...

  10. Selection rule engineering of forbidden transitions of a hydrogen atom near a nanogap (United States)

    Kim, Hyunyoung Y.; Kim, Daisik S.


    We perform an analytical study on the allowance of forbidden transitions for a hydrogen atom placed near line dipole sources, mimicking light emanating from a one-dimensional metallic nanogap. It is shown that the rapid variation of the electric field vector, inevitable in the near zone, completely breaks the selection rule of Δl=±1. While the forbidden transitions between spherically symmetric S states, such as 2S to 1S or 3S to 1S (Δl=0), are rather robust against selection rule breakage, Δl=±2 transitions such as between 3D and 1S or 3D and 2S states are very vulnerable to the spatial variation of the perturbing electric field. Transitions between 2S and 3D states are enhanced by many orders of magnitude, aided by the quadratic nature of both the perturbing Hamiltonian and D wavefunctions. The forbidden dipole moment, which approaches one Bohr radius times the electric charge in the vicinity of the gap, can be written in a simple closed form owing to the one-dimensional nature of our gap. With large enough effective volume together with the symmetric nature of the excited state wavefunctions, our work paves way towards atomic physics application of infinitely long nanogaps.

  11. Selection rule engineering of forbidden transitions of a hydrogen atom near a nanogap

    Directory of Open Access Journals (Sweden)

    Kim Hyunyoung Y.


    Full Text Available We perform an analytical study on the allowance of forbidden transitions for a hydrogen atom placed near line dipole sources, mimicking light emanating from a one-dimensional metallic nanogap. It is shown that the rapid variation of the electric field vector, inevitable in the near zone, completely breaks the selection rule of Δl=±1. While the forbidden transitions between spherically symmetric S states, such as 2S to 1S or 3S to 1S (Δl=0, are rather robust against selection rule breakage, Δl=±2 transitions such as between 3D and 1S or 3D and 2S states are very vulnerable to the spatial variation of the perturbing electric field. Transitions between 2S and 3D states are enhanced by many orders of magnitude, aided by the quadratic nature of both the perturbing Hamiltonian and D wavefunctions. The forbidden dipole moment, which approaches one Bohr radius times the electric charge in the vicinity of the gap, can be written in a simple closed form owing to the one-dimensional nature of our gap. With large enough effective volume together with the symmetric nature of the excited state wavefunctions, our work paves way towards atomic physics application of infinitely long nanogaps.

  12. Mass-produced nanogap sensor arrays for ultrasensitive detection of DNA. (United States)

    Roy, Somenath; Chen, Xiaojun; Li, Mo-Huang; Peng, Yanfen; Anariba, Franklin; Gao, Zhiqiang


    In this report, an electrical detection scheme for the quantification of DNA using a nanogap sensor array is detailed. The prime objective is to develop a novel sensing procedure, based on the electronic transduction mechanism, which would mitigate the problems intrinsic to nanostructure-based biosensing devices. Design considerations of the sensor array take into account the feasibility of mass production in a cost-effective way by using standard silicon microfabrication technologies. The sensing mechanism relies on bridging the nanogap upon hybridization of the two termini of a target DNA with two different surface-bound capture probes, followed by a simple metallization step. About 2 orders of magnitude enhancement in conductance, as referred to a clean background (<1.0 pS) observed at a control sensor, was obtained in the presence of as little as 1.0 fM target DNA. This sensitivity is comparable to the best of electrochemical/electrical biosensors. A linear relationship between the conductance and the DNA concentration was obtained from 1.0 fM to 1.0 pM with an exceptional signal intensity of 2.1 x 10(4)% change per unit concentration. This change in conductivity is so large that it can unambiguously detect the concentration of DNA quantitatively and may obviate the need for target amplification used in current DNA tests. Moreover, the sensor array exhibited excellent single-base mismatch discrimination due to its unique vertically aligned nanostructure and the two-probe configuration.

  13. Sensing extremely limited H₂ contents by Pd nanogap connected to an amorphous InGaZnO thin-film transistor. (United States)

    Lee, Young Tack; Jung, Hwaebong; Nam, Seung Hee; Jeon, Pyo Jin; Kim, Jin Sung; Jang, Byungjin; Lee, Wooyoung; Im, Seongil


    A palladium (Pd) nanogap-based thin-film has been connected to an electrically stable amorphous InGaZnO thin-film transistor, to form a hydrogen sensor demonstrating a dramatic sensing capability. As a result of the Pd connection to the transistor source, our sensor circuit greatly enhances the hydrogen-induced signal and sensing speed in the sense of output voltage, clearly resolving a minimum hydrogen content of 0.05%. When the nanogap-based Pd thin-film was connected to the transistor gate, an extremely limited hydrogen content of even less than 0.05% was visibly detected through gate voltage shifts. Our results exhibit the most promising and practical ways to sense extremely limited hydrogen contents, originating from two methods: transistor-to-Pd nanogap resistor and transistor-to-Pd nanogap capacitor coupling.

  14. High temperature gradient nanogap-Pirani micro-sensor with maximum sensitivity around atmospheric pressure (United States)

    Ghouila-Houri, C.; Talbi, A.; Viard, R.; Moutaouekkil, M.; Elmazria, O.; Gallas, Q.; Garnier, E.; Merlen, A.; Pernod, P.


    This letter describes and discusses the design and testing of an efficient nanogap Pirani micro-sensor for pressure measurements in a wide range with a maximum sensitivity around atmospheric pressure. The structure combines a substrate-free heated wire and a mechanical support made of silicon oxide micro-bridges allowing both a constant nanoscale gap between the wire and the substrate and a 1 mm long and 3 μm wide wire. The high aspect ratio of the wire provides a uniform heating profile along the wire and contributes to low pressure detection. On the contrary, both the nanoscale gap and the short wire length between two micro-bridges contribute to shift the high limit of the pressure range. When tested between 10 kPa and 800 kPa, the sensor presents a wide measurement range, not fully reached by the experiments, with a maximum of sensitivity close to the atmospheric pressure and performances with up to 38%/dec sensitivity when operating in a constant temperature mode with an overheat of 20 °C.

  15. Self-assembled nanogaps via seed-mediated growth of end-to-end linked gold nanorods

    DEFF Research Database (Denmark)

    Jain, Titoo; Westerlund, Axel Rune Fredrik; Johnson, Erik


    on the nanoscale. We here present a new way to end-to-end link AuNRs with a single or few linker molecules. Whereas methods reported in the literature so far rely on modification of the AuNRs after the synthesis, we here dimerize gold nanoparticle seeds with a water-soluble dithiol-functionalized polyethylene......Gold nanorods (AuNRs) are of interest for a wide range of applications, ranging from imaging to molecular electronics, and they have been studied extensively for the past decade. An important issue in AuNR applications is the ability to self-assemble the rods in predictable structures...... that a large fraction of the rods are flexible around the hinging molecule in solution, as expected for a molecularly linked nanogap. By using excess of gold nanoparticles relative to the linking dithiol molecule, this method can provide a high probability that a single molecule is connecting the two rods...

  16. Tunable and Linker Free Nanogaps in Core-Shell Plasmonic Nanorods for Selective and Quantitative Detection of Circulating Tumor Cells by SERS. (United States)

    Zhang, Yang; Yang, Peng; Habeeb Muhammed, Madathumpady Abubaker; Alsaiari, Shahad K; Moosa, Basem; Almalik, Abdulaziz; Kumar, Anjli; Ringe, Emilie; Khashab, Niveen M


    Controlling the size, number, and shape of nanogaps in plasmonic nanostructures is of significant importance for the development of novel quantum plasmonic devices and quantitative sensing techniques such as surface-enhanced Raman scattering (SERS). Here, we introduce a new synthetic method based on coordination interactions and galvanic replacement to prepare core-shell plasmonic nanorods with tunable enclosed nanogaps. Decorating Au nanorods with Raman reporters that strongly coordinate Ag+ ions (e.g., 4-mercaptopyridine) afforded uniform nucleation sites to form a sacrificial Ag shell. Galvanic replacement of the Ag shell by HAuCl4 resulted in Au-AgAu core-shell structure with a uniform intra-nanoparticle gap. The size (length and width) and morphology of the core-shell plasmonic nanorods as well as the nanogap size depend on the concentration of the coordination complexes formed between Ag+ ions and 4-mercaptopyridine. Moreover, encapsulating Raman reporters within the nanogaps afforded an internal standard for sensitive and quantitative SERS analysis. To test the applicability, core-shell plasmonic nanorods were functionalized with aptamers specific to circulating tumor cells such as MCF-7 (Michigan Cancer Foundation-7, breast cancer cell line). This system could selectively detect as low as 20 MCF-7 cells in a blood mimicking fluid employing SERS. The linking DNA duplex on core-shell plasmonic nanorods can also intercalate hydrophobic drug molecules such as Doxorubicin, thereby increasing the versatility of this sensing platform to include drug delivery. Our synthetic method offers the possibility of developing multifunctional SERS-active materials with a wide range of applications including biosensing, imaging, and therapy.

  17. Tunable and Linker Free Nanogaps in Core-Shell Plasmonic Nanorods for Selective and Quantitative Detection of Circulating Tumor Cells by SERS

    KAUST Repository

    Zhang, Yang


    Controlling the size, number, and shape of nanogaps in plasmonic nanostructures is of significant importance for the development of novel quantum plasmonic devices and quantitative sensing techniques such as surface-enhanced Raman scattering (SERS). Here, we introduce a new synthetic method based on coordination interactions and galvanic replacement to prepare core-shell plasmonic nanorods with tunable enclosed nanogaps. Decorating Au nanorods with Raman reporters that strongly coordinate Ag+ ions (e.g., 4-mercaptopyridine) afforded uniform nucleation sites to form a sacrificial Ag shell. Galvanic replacement of the Ag shell by HAuCl4 resulted in Au-AgAu core-shell structure with a uniform intra-nanoparticle gap. The size (length and width) and morphology of the core-shell plasmonic nanorods as well as the nanogap size depends on the concentration of the coordination complexes formed between Ag+ ions and 4-mercaptopyridine. Moreover, encapsulating Raman reporters within the nanogaps afforded an internal standard for sensitive and quantitative SERS analysis. To test the applicability, core-shell plasmonic nanorods were functionalized with aptamers specific to circulating tumor cells such as MCF-7 (Michigan Cancer Foundation-7, breast cancer cell line). This system could selectively detect as low as 20 MCF-7 cells in a blood mimicking fluid employing SERS. The linking DNA duplex on core-shell plasmonic nanorods can also intercalate hydrophobic drug molecules such as Doxorubicin, thereby increasing the versatility of this sensing platform to include drug delivery. Our synthetic method offers the possibility of developing multifunctional SERS-active materials with a wide range of applications including bio sensing, imaging and therapy.

  18. Optical Dark-Field and Electron Energy Loss Imaging and Spectroscopy of Symmetry-Forbidden Modes in Loaded Nanogap Antennas. (United States)

    Brintlinger, Todd; Herzing, Andrew A; Long, James P; Vurgaftman, Igor; Stroud, Rhonda; Simpkins, B S


    We have produced large numbers of hybrid metal-semiconductor nanogap antennas using a scalable electrochemical approach and systematically characterized the spectral and spatial character of their plasmonic modes with optical dark-field scattering, electron energy loss spectroscopy with principal component analysis, and full wave simulations. The coordination of these techniques reveal that these nanostructures support degenerate transverse modes which split due to substrate interactions, a longitudinal mode which scales with antenna length, and a symmetry-forbidden gap-localized transverse mode. This gap-localized transverse mode arises from mode splitting of transverse resonances supported on both antenna arms and is confined to the gap load enabling (i) delivery of substantial energy to the gap material and (ii) the possibility of tuning the antenna resonance via active modulation of the gap material's optical properties. The resonant position of this symmetry-forbidden mode is sensitive to gap size, dielectric strength of the gap material, and is highly suppressed in air-gapped structures which may explain its absence from the literature to date. Understanding the complex modal structure supported on hybrid nanosystems is necessary to enable the multifunctional components many seek.

  19. Plasmonic Near-Field Localization of Silver Core-Shell Nanoparticle Assemblies via Wet Chemistry Nanogap Engineering. (United States)

    Asapu, Ramesh; Ciocarlan, Radu-George; Claes, Nathalie; Blommaerts, Natan; Minjauw, Matthias; Ahmad, Tareq; Dendooven, Jolien; Cool, Pegie; Bals, Sara; Denys, Siegfried; Detavernier, Christophe; Lenaerts, Silvia; Verbruggen, Sammy W


    Silver nanoparticles are widely used in the field of plasmonics because of their unique optical properties. The wavelength-dependent surface plasmon resonance gives rise to a strongly enhanced electromagnetic field, especially at so-called hot spots located in the nanogap in-between metal nanoparticle assemblies. Therefore, the interparticle distance is a decisive factor in plasmonic applications, such as surface-enhanced Raman spectroscopy (SERS). In this study, the aim is to engineer this interparticle distance for silver nanospheres using a convenient wet-chemical approach and to predict and quantify the corresponding enhancement factor using both theoretical and experimental tools. This was done by building a tunable ultrathin polymer shell around the nanoparticles using the layer-by-layer method, in which the polymer shell acts as the separating interparticle spacer layer. Comparison of different theoretical approaches and corroborating the results with SERS analytical experiments using silver and silver-polymer core-shell nanoparticle clusters as SERS substrates was also done. Herewith, an approach is provided to estimate the extent of plasmonic near-field enhancement both theoretically as well as experimentally.

  20. Terahertz nanogap antenna detection of nano-bridges and nano-rods (United States)

    Park, H. R.; Seo, M. A.; Kyoung, J. S.; Koo, S. M.; Suwal, O. K.; Choi, S. S.; Park, N. K.; Kim, D. S.


    We have measured transmission properties of a composite structure consisting of nano-rods on a long (ay=300 micron) nano gap (70 nm) on Au film in broad frequency range of 0.1 THz to 1.0 THz using THz time-domain spectroscopy. The normalized transmittance with no nano-bridge or nanorod structure in the middle shows a half-wavelength resonance: the resonance frequency is ˜c/(2nay) where n is the index of refraction of the substrate. The nano-size bridge at the center of the nano gap gives changes the resonance characteristics profoundly, because in essence, the length ay now halves. Mostly the same resonance-changing behavior is expected with a nano rod structure fabricated by Pt-deposition method using a focused ion beam (FIB). This small rod also acts as a bridge dividing the length of the rectangle. We also positioned nano-rods to lie at one third of each nano gap, dividing the length by the ratio of 1: 2. A resonance peak shift was observed. The structure dependent resonance allows to detect nano-size particles and to tailor resonance characteristics with feature sizes of λ/10,000.

  1. Fabrication Facilities (United States)

    Federal Laboratory Consortium — The Fabrication Facilities are a direct result of years of testing support. Through years of experience, the three fabrication facilities (Fort Hood, Fort Lewis, and...

  2. Fabrication of SWCNT-Graphene Field-Effect Transistors

    Directory of Open Access Journals (Sweden)

    Shuangxi Xie


    Full Text Available Graphene and single-walled carbon nanotube (SWCNT have been widely studied because of their extraordinary electrical, thermal, mechanical, and optical properties. This paper describes a novel and flexible method to fabricate all-carbon field-effect transistors (FETs. The fabrication process begins with assembling graphene grown by chemical vapor deposition (CVD on a silicon chip with SiO2 as the dielectric layer and n-doped Si substrate as the gate. Next, an atomic force microscopy (AFM-based mechanical cutting method is utilized to cut the graphene into interdigitated electrodes with nanogaps, which serve as the source and drain. Lastly, SWCNTs are assembled on the graphene interdigitated electrodes by dielectrophoresis to form the conductive channel. The electrical properties of the thus-fabricated SWCNT-graphene FETs are investigated and their FET behavior is confirmed. The current method effectively integrates SWCNTs and graphene in nanoelectronic devices, and presents a new method to build all-carbon electronic devices.

  3. Digital fabrication

    CERN Document Server


    The Winter 2012 (vol. 14 no. 3) issue of the Nexus Network Journal features seven original papers dedicated to the theme “Digital Fabrication”. Digital fabrication is changing architecture in fundamental ways in every phase, from concept to artifact. Projects growing out of research in digital fabrication are dependent on software that is entirely surface-oriented in its underlying mathematics. Decisions made during design, prototyping, fabrication and assembly rely on codes, scripts, parameters, operating systems and software, creating the need for teams with multidisciplinary expertise and different skills, from IT to architecture, design, material engineering, and mathematics, among others The papers grew out of a Lisbon symposium hosted by the ISCTE-Instituto Universitario de Lisboa entitled “Digital Fabrication – A State of the Art”. The issue is completed with four other research papers which address different mathematical instruments applied to architecture, including geometric tracing system...

  4. An Ethology of Urban Fabric(s)

    DEFF Research Database (Denmark)

    Fritsch, Jonas; Thomsen, Bodil Marie Stavning


    The article explores a non-metaphorical understanding of urban fabric(s), shifting the attention from a bird’s eye perspective to the actual, textural manifestations of a variety of urban fabric(s) to be studied in their real, processual, ecological and ethological complexity within urban life. We...... effectuate this move by bringing into resonance a range of intersecting fields that all deal with urban fabric(s) in complementary ways (interaction design and urban design activism, fashion, cultural theory, philosophy, urban computing)....

  5. Fabrication and Prototyping Lab (United States)

    Federal Laboratory Consortium — Purpose: The Fabrication and Prototyping Lab for composite structures provides a wide variety of fabrication capabilities critical to enabling hands-on research and...

  6. Fabrication of recyclable superhydrophobic cotton fabrics (United States)

    Han, Sang Wook; Park, Eun Ji; Jeong, Myung-Geun; Kim, Il Hee; Seo, Hyun Ook; Kim, Ju Hwan; Kim, Kwang-Dae; Kim, Young Dok


    Commercial cotton fabric was coated with SiO2 nanoparticles wrapped with a polydimethylsiloxane (PDMS) layer, and the resulting material surface showed a water contact angle greater than 160°. The superhydrophobic fabric showed resistance to water-soluble contaminants and maintained its original superhydrophobic properties with almost no alteration even after many times of absorption-washing cycles of oil. Moreover, superhydrophobic fabric can be used as a filter to separate oil from water. We demonstrated a simple method of fabrication of superhydrophobic fabric with potential interest for use in a variety of applications.


    Directory of Open Access Journals (Sweden)

    Özlem KISAOĞLU


    Full Text Available Woven fabric quality depends on yarn properties at first, then weaving preparation and weaving processes. Defect control of grey and finished fabric is done manually on the lighted tables or automatically. Fabrics can be controlled by the help of the image analysis method. In image system the image of fabrics can be digitized by video camera and after storing controlled by the various processing. Recently neural networks, fuzzy logic, best wavelet packet model on automatic fabric inspection are developed. In this study the advantages and disadvantages of manual and automatic, on-line fabric inspection systems are given comparatively.

  8. Fabrication of Superhydrophilic Wool Fabrics By Nanotechnology (United States)

    Chen, Dong

    Because of the fatty layer on its surface, wool fiber is hydrophobic, which results in poor water absorption and wicking properties that affect the comfort of wool textiles. The purpose of this research is to improve the wettability and comfort of wool textiles using nanotechnology. To reveal the knowledge gaps and ensure the originality of this study, a critical review of literature was conducted in relevant areas. To achieve the objectives of the research, a simple method for fabricating environmentally stable superhydrophilic wool fabrics was developed. Silica sols with diameters of 27 nm were prepared and then coated on the surface of pristine wool fibers to form an ultrathin layer, increasing both the surface roughness and energy. The morphology and composition of silica-sol-coated wool fabrics were characterized by a combination of SEM, TEM, FTIR, and XPS measurements. After evaluating the wettability and washing durability of the silica-sol-coated wool fabrics, it was found that the durability of these wool fabrics needed to be improved. To achieve superhydrophilic wool fabrics with good washing durability, reactive siloxane was functionalized on wool fiber surface, and an ultrathin silica nanoparticles layer was grafted on the surface by in-situ growth method. To evaluate the wettability change of silica grafted wool fabric, in addition to the contact angle, in-depth characterizations of water absorbing and drying properties of wool fabrics were measured. According to Chinese National Standard (GB/T 21655.1-2008 and GB/T 21655.2-2009), the prepared silica grafted wool fabric has excellent water absorbing and quick drying properties that can be maintained after washing 20 times in a washing machine. The strategy of siloxane bonding and in-situ growth was successfully extended to durable multifunctional wool fabrics combined with superhydrophilic, self-cleaning, and antibacterial properties. To study the relationships between functional properties and nano

  9. Crimp-Imbalanced Fabrics (United States)


    references of Howland describe plain-woven fabrics possessing cover factors (CF) up to one hundred percent for warp fibers at the weft center and in excess...iso-crimped multi-layered fabrics. [0087] Key advantages over current crimped fabric armor systems are discussed here. First, regions of oblique

  10. Photochemical cutting of fabrics (United States)

    Piltch, Martin S.


    Apparatus for the cutting of garment patterns from one or more layers of fabric. A laser capable of producing laser light at an ultraviolet wavelength is utilized to shine light through a pattern, such as a holographic phase filter, and through a lens onto the one or more layers of fabric. The ultraviolet laser light causes rapid photochemical decomposition of the one or more layers of fabric, but only along the pattern. The balance of the fabric of the one or more layers of fabric is undamaged.

  11. Fabricating architectural volume

    DEFF Research Database (Denmark)

    Feringa, Jelle; Søndergaard, Asbjørn


    The 2011 edition of Fabricate inspired a number of collaborations, this article seeks to highlight three of these. There is a common thread amongst the projects presented: sharing the ambition to close the rift between design and fabrication while incorporating structural design aspects early on...

  12. Fabrics in Function

    DEFF Research Database (Denmark)

    Bang, Anne Louise


    sensing of fabrics in function. It is proposed that tactile and visual sensing of fabrics is a way to investigate and express emotional utility values. The further purpose is to use experiments with repertory grid models as part of the mapping of the entire research project and also as a basis...

  13. Magnetic fabrics in amphibolites (United States)

    Biedermann, Andrea Regina; Hirt, Ann M.; Kunze, Karsten


    Magnetic fabrics are used as indicators for mineral fabrics and thus tectonic settings. In particular, the maximum and minimum magnetic susceptibilities are often taken as representation of the direction of macroscopic lineation and pole to foliation of a rock, respectively. In rocks consisting mainly of amphiboles, the paramagnetic fabric is controlled by the preferential orientation of the amphibole crystals. These crystals normally have their c-axis aligned with lineation, however, the maximum susceptibility is parallel to the crystallographic b-axis, leading to more complicated relationships between the orientations of the magnetic fabric and mineral fabric. Here we describe magnetic fabrics in two amphibolites, both deformed and containing 70 % hornblende. Both amphibolites possess significant magnetic anisotropy with the minimum susceptibility normal to foliation. However, maximum susceptibility and lineation are parallel in one amphibolite, whereas they deviate in the other. Numerical models, which simulate the magnetic anisotropy based on the measured crystallographic preferred orientation (CPO) of hornblende and single crystal anisotropy, can reproduce the observed magnetic fabrics in these samples. Furthermore, synthetic models help explain for which types of CPO the magnetic and mineral lineations are parallel to each other, and when they are not aligned to one another. The results presented here will help in future interpretation of mineral fabrics in amphibole-bearing rocks.

  14. Smart Fabrics Technology Development (United States)

    Simon, Cory; Potter, Elliott; Potter, Elliott; McCabe, Mary; Baggerman, Clint


    Advances in Smart Fabrics technology are enabling an exciting array of new applications for NASA exploration missions, the biomedical community, and consumer electronics. This report summarizes the findings of a brief investigation into the state of the art and potential applications of smart fabrics to address challenges in human spaceflight.

  15. Fabricating a shoulder somatoprosthesis. (United States)

    Blumenfeld, I; Schortz, R H; Levy, M; Lepley, J B


    A technique for the fabrication of a shoulder prosthesis has been described. The prosthesis has proven to be an effective means of rehabilitating a patient following an intrascapulothoracic amputation. The patient may once again wear clothing without having it adjusted to conform to the defect. Such rehabilitation has been of great psychologic value for patients and their families as well. The impression and processing procedures are effective for the fabrication of a shoulder prosthesis. The principles of this technique may be applied to the fabrication of other large somatoprostheses.

  16. Deterioration of airplane fabrics (United States)

    Wendt, FR


    The observation that airplane fabrics, after long use, lose their original strength, caused the German Experimental Institute for Aviation to carry out a series of experiments on the effect of weathering on the cloth covering of airplane wings and fuselages.

  17. Superabsorbent Multilayer Fabric (United States)

    Coreale, J. V.; Dawn, F. S.


    Material contains gel-forming polymer and copolymer that absorb from 70 to 200 times their weight of liquid. Superabsorbent Polymer and Copolymer form gels to bind and retain liquid in multiply fabric. Until reaction between liquid and absorbent masses forms gel, backing layer retains liquids within fabric; also allows material to "breathe." Possible applications include baby diapers, female hygiene napkins, and hospital bedpads. Might also have uses in improvement of dry soil.

  18. Nuclear Fabrication Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Levesque, Stephen [EWI, Columbus, OH (United States)


    This report summarizes the activities undertaken by EWI while under contract from the Department of Energy (DOE) Office of Nuclear Energy (NE) for the management and operation of the Nuclear Fabrication Consortium (NFC). The NFC was established by EWI to independently develop, evaluate, and deploy fabrication approaches and data that support the re-establishment of the U.S. nuclear industry: ensuring that the supply chain will be competitive on a global stage, enabling more cost-effective and reliable nuclear power in a carbon constrained environment. The NFC provided a forum for member original equipment manufactures (OEM), fabricators, manufacturers, and materials suppliers to effectively engage with each other and rebuild the capacity of this supply chain by : Identifying and removing impediments to the implementation of new construction and fabrication techniques and approaches for nuclear equipment, including system components and nuclear plants. Providing and facilitating detailed scientific-based studies on new approaches and technologies that will have positive impacts on the cost of building of nuclear plants. Analyzing and disseminating information about future nuclear fabrication technologies and how they could impact the North American and the International Nuclear Marketplace. Facilitating dialog and initiate alignment among fabricators, owners, trade associations, and government agencies. Supporting industry in helping to create a larger qualified nuclear supplier network. Acting as an unbiased technology resource to evaluate, develop, and demonstrate new manufacturing technologies. Creating welder and inspector training programs to help enable the necessary workforce for the upcoming construction work. Serving as a focal point for technology, policy, and politically interested parties to share ideas and concepts associated with fabrication across the nuclear industry. The report the objectives and summaries of the Nuclear Fabrication Consortium

  19. Fabric space radiators

    Energy Technology Data Exchange (ETDEWEB)

    Antoniak, Z.I.; Krotiuk, W.J.; Webb, B.J.; Prater, J.T.; Bates, J.M.


    Future Air Force space missions will require thermal radiators that both survive in the hostile space environment and stow away for minimal bulk during launch. Advances in all aspects of radiator design, construction, and analysis will be necessary to enable such future missions. Currently, the best means for obtaining high strength along with flexibility is through structures known as fabrics. The development of new materials and bonding techniques has extended the application range of fabrics into areas traditionally dominated by monolithic and/or metallic structures. Given that even current spacecraft heat rejection considerations tend to dominate spacecraft design and mass, the larger and more complex designs of the future face daunting challenges in thermal control. Ceramic fabrics bonded to ultra-thin metal liners (foils) have the potential of achieving radiator performance levels heretofore unattainable, and of readily matching the advances made in other branches of spacecraft design. The research effort documented here indicates that both pumped loops and heat pipes constructed in ceramic fabrics stand to benefit in multiple ways. Flexibility and low mass are the main advantages exhibited by fabric radiators over conventional metal ones. We feel that fabric radiators have intrinsic merits not possessed by any other radiator design and need to be researched further. 26 refs., 16 figs., 17 tabs.

  20. Fabrication of PDMS architecture (United States)

    Adam, Tijjani; Hashim, U.


    The study report novel, yet simple and flexible fabrication method for micro channel patterning PDMS thin mold on glass surfaces, the method allows microstructures with critical dimensions to be formed using PDMS. Micro channel production is a two-step process. First, soft photolithography methods are implemented to fabricate a reusable mold. The mold is then used to create the micro channel, which consists of SU8, PDMS and glass. The micro channel design was performed using AutoCAD and the fabrication begins by creating a replicable mold. The mold is created on a glass slide. by spin-coating speed between 500 to 1250rpm with an acceleration of 100 rpm/s for 100 and 15 second ramp up and down speed respectively. Channel flow rate based on concentration were measured by analyzing the recorded flow profiles which was collected from the high powered microscope at. 80µ, 70µm, 50µm for inlet channel 1, 2, 3 respectively the channel flow were compared for flow efficiency at different concentrations and Re. Thus, the simplicity of device structure and fabrication makes it feasible to miniaturize it for the development of point-of-care kits, facilitating its use in both clinical and non-clinical environments. With its simple geometric structure and potential for mass commercial fabrication, the device can be developed to become a portable photo detection sensor that can be use for both environmental and diagnostic application.

  1. ITA Sensor Fabric (United States)

    Wright, Joel; Gibson, Christopher; Bergamaschi, Flavio; Marcus, Kelvin; Pham, Tien; Pressley, Ryan; Verma, Gunjan


    The diverse sensor types and networking technologies commonly used in fielded sensro networks provide a unique set of challenges [1] in the areas of sensor identification, interoperability, and sensor data consumability. The ITA Senor Fabric is a middleware infrastructure - developed as part of the International Technology Alliance (ITA)[2] in Network and Information Science - that addresses these challenges by providing unified access to, and management of, sensor networks. The Fabric spans the network from command and control, through forward operating bases, and out to mobile forces and fielded sensors, maximizing the availability and utility of intelligence information to users.

  2. Fabrication activity for nanophotonics

    DEFF Research Database (Denmark)

    Malureanu, Radu; Chung, Il-Sug; Carletti, Luca

    We present the fabrication and characterization of new structures and materials to be used in nanophotonics. The first structure presented is a fractal metallic metasurface designed to be used as a high-sensitivity sensor for 810nm wavelength. A second structure is a high index contrast grating...

  3. cotton fabric 51

    African Journals Online (AJOL)


    Some salient properties of cotton cellulose which requires it to be treated with additives to improve its versatility were examined taken ... modification of the cotton cellulose upon resination with methylolmelamine phosphate. Keywords: Cotton Fabric ..... Decomposition of Pure Cellulose and Pulp. Paper. Polym Degrad Stab.

  4. Lithographic fabrication of nanoapertures (United States)

    Fleming, James G.


    A new class of silicon-based lithographically defined nanoapertures and processes for their fabrication using conventional silicon microprocessing technology have been invented. The new ability to create and control such structures should significantly extend our ability to design and implement chemically selective devices and processes.

  5. Dyeing fabrics with metals (United States)

    Kalivas, Georgia


    Traditionally, in textile dyeing, metals have been used as mordants or to improve the color produced by a natural or synthetic dye. In biomedical research and clinical diagnostics gold colloids are used as sensitive signals to detect the presence of pathogens. It has been observed that when metals are finely divided, a distinct color may result that is different from the color of the metal in bulk. For example, when gold is finely divided it may appear black, ruby or purple. This can be seen in biomedical research when gold colloids are reduced to micro-particles. Bright color signals are produced by few nanometer-sized particles. Dr. William Todd, a researcher in the Department of Veterinary Science at the Louisiana State University, developed a method of dyeing fabrics with metals. By using a reagent to bond the metal particles deep into the textile fibers and actually making the metal a part of the chemistry of the fiber. The chemicals of the fabric influence the resulting color. The combination of the element itself, the size of the particle, the chemical nature of the particle and the interaction of the metal with the chemistry of the fabric determine the actual hue. By using different elements, reagents, textiles and solvents a broad range of reproducible colors and tones can be created. Metals can also be combined into alloys, which will produce a variety of colors. The students of the ISCC chapter at the Fashion Institute of Technology dyed fabric using Dr. Todd's method and created a presentation of the results. They also did a demonstration of dyeing fabrics with metals.

  6. Status report, canister fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Andersson, Claes-Goeran; Eriksson, Peter; Westman, Marika [Swedish Nuclear Fuel and Waste Management Co., Stockholm (Sweden); Emilsson, Goeran [CSM Materialteknik AB, Linkoeping (Sweden)


    The report gives an account of the development of material and fabrication technology for copper canisters with cast inserts during the period from 2000 until the start of 2004. The engineering design of the canister and the choice of materials in the constituent components described in previous status reports have not been significantly changed. In the reference canister, the thickness of the copper shell is 50 mm. Fabrication of individual components with a thinner copper thickness is done for the purpose of gaining experience and evaluating fabrication and inspection methods for such canisters. As a part of the development of cast inserts, computer simulations of the casting processes and techniques used at the foundries have been performed for the purpose of optimizing the material properties. These properties have been evaluated by extensive tensile testing and metallographic inspection of test material taken from discs cut at different points along the length of the inserts. The testing results exhibit a relatively large spread. Low elongation values in certain tensile test specimens are due to the presence of poorly formed graphite, porosities, slag or other casting defects. It is concluded in the report that it will not be possible to avoid some presence of observed defects in castings of this size. In the deep repository, the inserts will be exposed to compressive loading and the observed defects are not critical for strength. An analysis of the strength of the inserts and formulation of relevant material requirements must be based on a statistical approach with probabilistic calculations. This work has been initiated and will be concluded during 2004. An initial verifying compression test of a canister in an isostatic press has indicated considerable overstrength in the structure. Seamless copper tubes are fabricated by means of three methods: extrusion, pierce and draw processing, and forging. It can be concluded that extrusion tests have revealed a

  7. The Fabric of Reality (United States)

    Whitaker, Andrew

    David Deutsch, The Fabric of Reality (London: Allen Lane, 1997), x+390 pp., ISBN 0-713-990619, hardback. David Deutsch's popular book, The Fabric of Reality, has already won acclaim as a sustained and comprehensible explanation of his own worldview, which encompasses his four main strands of quantum physics, epistemology, computation and evolution, as well as the many connections between them. Deutsch is a strong opponent of reductionism, and the latter three strands are 'high level' theories compared to quantum physics; but all four are to be regarded as fundamental because they are the theories that provide the deepest explanations. Deutsch considers that his worldview may be called the first genuine Theory of Everything; it would stand in strong contrast to the reductionist theories given that title at present. In fact he believes his approach may enable us to unify and explain not just science, but philosophy, logic, mathematics, ethics, politics and aesthetics.

  8. Fabrication of diamond shells (United States)

    Hamza, Alex V.; Biener, Juergen; Wild, Christoph; Woerner, Eckhard


    A novel method for fabricating diamond shells is introduced. The fabrication of such shells is a multi-step process, which involves diamond chemical vapor deposition on predetermined mandrels followed by polishing, microfabrication of holes, and removal of the mandrel by an etch process. The resultant shells of the present invention can be configured with a surface roughness at the nanometer level (e.g., on the order of down to about 10 nm RMS) on a mm length scale, and exhibit excellent hardness/strength, and good transparency in the both the infra-red and visible. Specifically, a novel process is disclosed herein, which allows coating of spherical substrates with optical-quality diamond films or nanocrystalline diamond films.

  9. Fabrication of freeform optics (United States)

    Blalock, Todd; Medicus, Kate; DeGroote Nelson, Jessica


    Freeform surfaces on optical components have become an important design tool for optical designers. Non-rotationally symmetric optical surfaces have made solving complex optical problems easier. The manufacturing and testing of these surfaces has been the technical hurdle in freeform optic's wide-spread use. Computer Numerically Controlled (CNC) optics manufacturing technology has made the fabrication of optical components more deterministic and streamlined for traditional optics and aspheres. Optimax has developed a robust freeform optical fabrication CNC process that includes generation, high speed VIBE polishing, sub-aperture figure correction, surface smoothing and testing of freeform surfaces. Metrology of freeform surface is currently achieved with coordinate measurement machines (CMM) for lower resolution and interferometry with computer generated holograms (CGH) for high resolution irregularity measurements.

  10. Fabrication of Nanochannels

    Directory of Open Access Journals (Sweden)

    Yuqi Zhang


    Full Text Available Nature has inspired the fabrication of intelligent devices to meet the needs of the advanced community and better understand the imitation of biology. As a biomimetic nanodevice, nanochannels/nanopores aroused increasing interest because of their potential applications in nanofluidic fields. In this review, we have summarized some recent results mainly focused on the design and fabrication of one-dimensional nanochannels, which can be made of many materials, including polymers, inorganics, biotic materials, and composite materials. These nanochannels have some properties similar to biological channels, such as selectivity, voltage-dependent current fluctuations, ionic rectification current and ionic gating, etc. Therefore, they show great potential for the fields of biosensing, filtration, and energy conversions. These advances can not only help people to understand the living processes in nature, but also inspire scientists to develop novel nanodevices with better performance for mankind.

  11. Fabrication of zein nanostructure (United States)

    Luecha, Jarupat

    The concerns on the increase of polluting plastic wastes as well as the U.S. dependence on imported petrochemical products have driven an attention towards alternative biodegradable polymers from renewable resources. Zein protein, a co-product from ethanol production from corn, is a good candidate. This research project aims to increase zein value by adopting nanotechnology for fabricating advanced zein packaging films and zein microfluidic devices. Two nanotechnology approaches were focused: the polymer nanoclay nanocomposite technique where the nanocomposite structures were created in the zein matrix, and the soft lithography and the microfluidic devices where the micro and nanopatterns were created on the zein film surfaces. The polymer nanoclay nanocomposite technique was adopted in the commonly used zein film fabrication processes which were solvent casting and extrusion blowing methods. The two methods resulted in partially exfoliated nanocomposite structures. The impact of nanoclays on the physical properties of zein films strongly depended on the film preparation techniques. The impact of nanoclay concentration was more pronounced in the films made by extrusion blowing technique than by the solvent casting technique. As the processability limitation for the extrusion blowing technique of the zein sample containing hight nanoclay content, the effect of the nanoclay content on the rheological properties of zein hybrid resins at linear and nonlinear viscoelastic regions were further investigated. A pristine zein resin exhibited soft solid like behavior. On the other hand, the zein hybrid with nanoclay content greater than 5 wt.% showed more liquid like behavior, suggesting that the nanoclays interrupted the entangled zein network. There was good correspondence between the experimental data and the predictions of the Wagner model for the pristine zein resins. However, the model failed to predict the steady shear properties of the zein nanoclay nanocomposite

  12. AFIP-2 Fabrication Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Glenn Moore


    The Advanced Test Reactor (ATR) Full-size Plate In Center Flux Trap Position (AFIP)-2 experiment was designed to evaluate the performance of monolithic fuels at a scale prototypic of research reactor fuel plates. Two qualified fueled plates were fabricated for the AFIP 2 experiment to be irradiated in the Idaho National Laboratory ATR. This report provides details of the fuel fabrication efforts, including material selection, fabrication processes, and fuel plate qualification.

  13. AFIP-6 Fabrication Summary Report

    Energy Technology Data Exchange (ETDEWEB)

    Glenn A. Moore; M. Craig Marshall


    The AFIP-6 (ATR Full-size plate In center flux trap Position) experiment was designed to evaluate the performance of monolithic fuels at a scale prototypic of research reactor fuel plates. Two qualified fueled plates were fabricated for the AFIP-6 experiment; to be irradiated in the INL Advanced Test Reactor (ATR). This report provides details of the fuel fabrication efforts, including material selection, fabrication processes, and fuel plate qualification.

  14. Filter Fabrics for Airport Drainage. (United States)


    pneumatically filling a woven polypropylene stocking with sand and vibrating it into a prebored hole, while another method uses a polyester nonwoven fabric...Selected Nonwoven Filter Fabrics," Letter Report, June 1977, U. S. Army Engineer Waterways Experiment Station, CE, Vicksburg, Miss. 18. BalL, J. E...woven and nonwoven plastic filter fabric. It has been developed based on limited field performance observations and the laboratory test evaluation of

  15. Ultraviolet Protection by Fabric Engineering

    Directory of Open Access Journals (Sweden)

    Mukesh Kumar Singh


    Full Text Available Background. The increasing emission of greenhouse gases has evoked the human being to save the ozone layer and minimize the risk of ultraviolet radiation (UVR. Various fabric structures have been explored to achieve desired ultraviolet protection factor (UPF in various situations. Objective. In this study, the effect of various filament configurations like twisted, flat, intermingled, and textured in multifilament yarns on fabric in different combinations is assessed in order to engineer a fabric of better ultraviolet protection factor (UPF. Methods. In order to engineer a fabric having optimum UV protection with sufficient comfort level in multifilament woven fabrics, four different yarn configurations, intermingled, textured, twisted, and flat, were used to develop twelve different fabric samples. The most UV absorbing and most demanding fibre polyethylene terephthalate (PET was considered in different filament configuration. Results. The combinations of intermingled warp with flat, intermingled, and textured weft provided excellent UVR protection comparatively at about 22.5 mg/cm2 fabric areal density. The presence of twisted yarn reduced the UV protection due to enhanced openness in fabric structure. Conclusion. The appropriate combination of warp and weft threads of different configuration should be selected judiciously in order to extract maximum UV protection and wear comfort attributes in multifilament woven PET fabrics.

  16. Fabrication of nanowires and nanostructures

    DEFF Research Database (Denmark)

    Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.; Piraux, L.


    We report on different approaches that we have adopted and developed for the fabrication of nanowires and nanostructures. Methods based on template synthesis and on self organization seem to be the most promising for the fabrication of nanomaterials and nanostructures due to their easiness and low...... cost. The development of a supported nanoporous alumina template and the possibility of using this template to combine electrochemical synthesis with lithographic methods open new ways for the fabrication of complex nanostructures. The numerous advantages of the supported template and its compatibility...... with microelectronic processes make it an ideal candidate for further integration into large-scale fabrication of various nanowire-based devices....

  17. Nozzle fabrication technique (United States)

    Wells, Dennis L. (Inventor)


    This invention relates to techniques for fabricating hour glass throat or convergent divergent nozzle shapes, and more particularly to new and improved techniques for forming rocket nozzles from electrically conductive material and forming cooling channels in the wall thereof. The concept of positioning a block of electrically conductive material so that its axis is set at a predetermined skew angle with relation to a travelling electron discharge machine electrode and thereafter revolving the body about its own axis to generate a hyperbolic surface of revolution, either internal or external is novel. The method will generate a rocket nozzle which may be provided with cooling channels using the same control and positioning system. The configuration of the cooling channels so produced are unique and novel. Also the method is adaptable to nonmetallic material using analogous cutting tools, such as, water jet, laser, abrasive wire and hot wire.

  18. Fabric circuits and method of manufacturing fabric circuits (United States)

    Chu, Andrew W. (Inventor); Dobbins, Justin A. (Inventor); Scully, Robert C. (Inventor); Trevino, Robert C. (Inventor); Lin, Greg Y. (Inventor); Fink, Patrick W. (Inventor)


    A flexible, fabric-based circuit comprises a non-conductive flexible layer of fabric and a conductive flexible layer of fabric adjacent thereto. A non-conductive thread, an adhesive, and/or other means may be used for attaching the conductive layer to the non-conductive layer. In some embodiments, the layers are attached by a computer-driven embroidery machine at pre-determined portions or locations in accordance with a pre-determined attachment layout before automated cutting. In some other embodiments, an automated milling machine or a computer-driven laser using a pre-designed circuit trace as a template cuts the conductive layer so as to separate an undesired portion of the conductive layer from a desired portion of the conductive layer. Additional layers of conductive fabric may be attached in some embodiments to form a multi-layer construct.

  19. Fabricating Copper Nanotubes by Electrodeposition (United States)

    Yang, E. H.; Ramsey, Christopher; Bae, Youngsam; Choi, Daniel


    Copper tubes having diameters between about 100 and about 200 nm have been fabricated by electrodeposition of copper into the pores of alumina nanopore membranes. Copper nanotubes are under consideration as alternatives to copper nanorods and nanowires for applications involving thermal and/or electrical contacts, wherein the greater specific areas of nanotubes could afford lower effective thermal and/or electrical resistivities. Heretofore, copper nanorods and nanowires have been fabricated by a combination of electrodeposition and a conventional expensive lithographic process. The present electrodeposition-based process for fabricating copper nanotubes costs less and enables production of copper nanotubes at greater rate.

  20. Natural fabric of Hildegardia populifolia composites

    CSIR Research Space (South Africa)

    Guduri, BBR


    Full Text Available The influence of Hildegardia populofolia fabric content, fabric orientation, sodium hydroxide (NaOH) and silane coupling agent treatment on the surface properties of the fabric, mechanical and fracture properties of Hildegardia populifolia...

  1. Fabrication of integrated metallic MEMS devices

    DEFF Research Database (Denmark)

    Yalcinkaya, Arda Deniz; Ravnkilde, Jan Tue; Hansen, Ole


    A simple and complementary metal oxide semiconductor (CMOS) compatible fabrication technique for microelectromechanical (MEMS) devices is presented. The fabrication technology makes use of electroplated metal layers. Among the fabricated devices, high quality factor microresonators...

  2. Plasmonic components fabrication via nanoimprint

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra


    A review report on nanoimprinted plasmonic components is given. The fabrication of different metal–dielectric geometries and nanostructured surfaces that support either propagating or localized surface plasmon modes is discussed. The main characteristics and advantages of the nanoimprint technology...... for the fabrication of various plasmonic structures are outlined. The discussion of plasmonic waveguiding structures focuses on planar waveguides based on metal strips embedded into a dielectric and on profiled metal surfaces. Nanoimprint-based fabrication of two-dimensional nanostructured plasmonic surfaces...... for enhanced transmission studies and sensor applications is also discussed. Throughout the report, the main fabrication schemes are described, as well as the challenges facing future manufacturing of plasmonic components for device applications....

  3. Geoacoustic Physical Model Fabrication Laboratory (United States)

    Federal Laboratory Consortium — FUNCTION: Fabricates three-dimensional rough surfaces (e.g., fractals, ripples) out of materials such as PVC or wax to simulate the roughness properties associated...

  4. Fabric Structures Team Technology Update (United States)


    testManufacturing Quilt Lines ofNon-Woven Composite , methods used, and overall benefits achieved. Payoff: • Enhanced non-woven composite tent liners... method on general purpose shelter fabric, as well as on tent liner fabrics. •Demonstrated efficacy with numerous biological and chemical agents Carbon...based Polymer gel electrolyte Ventana Reseach Corp. • Light-activated, reactive photocatalytic coatings that generate & reversibly store

  5. Fabricating customized hydrogel contact lens


    Andre Childs; Hao Li; Daniella M. Lewittes; Biqin Dong; Wenzhong Liu; Xiao Shu; Cheng Sun; Zhang, Hao F.


    Contact lenses are increasingly used in laboratories for in vivo animal retinal imaging and pre-clinical studies. The lens shapes often need modification to optimally fit corneas of individual test subjects. However, the choices from commercially available contact lenses are rather limited. Here, we report a flexible method to fabricate customized hydrogel contact lenses. We showed that the fabricated hydrogel is highly transparent, with refractive indices ranging from 1.42 to 1.45 in the spe...

  6. Washable and antibacterial superhydrophbic fabric (United States)

    Ou, Junfei; Wang, Zhile; Wang, Fajun; Xue, Mingshan; Li, Wen; Amirfazli, Alidad


    Inspired by the high adherence of mussel and the excellent water repellency of lotus leaf, superhydrophobic fabric is fabricated via the sequential deposition of polydopamine, Ag2O, and 1H,1H,2H,2H-perfluorodecanethiol, which shows excellent washability and high anti-bacterial activity due to the strong interfacial interaction and the surface silver species as well as the non-wettability, respectively.

  7. Fabricating plasmonic components for nanophotonics

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Nielsen, Rasmus Bundgaard; Jeppesen, Claus


    We report on experimental realization of different metal-dielectric structures that are used as surface plasmon polariton waveguides and as plasmonic metamaterials. Fabrication approaches based on different lithographic and deposition techniques are discussed.......We report on experimental realization of different metal-dielectric structures that are used as surface plasmon polariton waveguides and as plasmonic metamaterials. Fabrication approaches based on different lithographic and deposition techniques are discussed....

  8. Silicone nanocomposite coatings for fabrics (United States)

    Eberts, Kenneth (Inventor); Lee, Stein S. (Inventor); Singhal, Amit (Inventor); Ou, Runqing (Inventor)


    A silicone based coating for fabrics utilizing dual nanocomposite fillers providing enhanced mechanical and thermal properties to the silicone base. The first filler includes nanoclusters of polydimethylsiloxane (PDMS) and a metal oxide and a second filler of exfoliated clay nanoparticles. The coating is particularly suitable for inflatable fabrics used in several space, military, and consumer applications, including airbags, parachutes, rafts, boat sails, and inflatable shelters.

  9. ITER Central Solenoid Module Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Smith, John [General Atomics, San Diego, CA (United States)


    The fabrication of the modules for the ITER Central Solenoid (CS) has started in a dedicated production facility located in Poway, California, USA. The necessary tools have been designed, built, installed, and tested in the facility to enable the start of production. The current schedule has first module fabrication completed in 2017, followed by testing and subsequent shipment to ITER. The Central Solenoid is a key component of the ITER tokamak providing the inductive voltage to initiate and sustain the plasma current and to position and shape the plasma. The design of the CS has been a collaborative effort between the US ITER Project Office (US ITER), the international ITER Organization (IO) and General Atomics (GA). GA’s responsibility includes: completing the fabrication design, developing and qualifying the fabrication processes and tools, and then completing the fabrication of the seven 110 tonne CS modules. The modules will be shipped separately to the ITER site, and then stacked and aligned in the Assembly Hall prior to insertion in the core of the ITER tokamak. A dedicated facility in Poway, California, USA has been established by GA to complete the fabrication of the seven modules. Infrastructure improvements included thick reinforced concrete floors, a diesel generator for backup power, along with, cranes for moving the tooling within the facility. The fabrication process for a single module requires approximately 22 months followed by five months of testing, which includes preliminary electrical testing followed by high current (48.5 kA) tests at 4.7K. The production of the seven modules is completed in a parallel fashion through ten process stations. The process stations have been designed and built with most stations having completed testing and qualification for carrying out the required fabrication processes. The final qualification step for each process station is achieved by the successful production of a prototype coil. Fabrication of the first

  10. Fabrication of ceramic components using freeze-form extrusion fabrication (United States)

    Huang, Tieshu


    A novel, environmentally friendly solid freeform fabrication method called Freeze-form Extrusion Fabrication (FEF) has been developed for the fabrication of high temperature and ultra-high temperature ceramic-based components. The method is based on deposition of ceramic pastes using water as the medium. The FEF system components and their interaction are examined, and the main process parameters affecting part geometry are defined. Three-dimensional (3D) shaped components have been fabricated by extrusion deposition of the ceramic paste in a layer-by-layer fashion. The feasibility of this process has been demonstrated by building components having a simple geometry, such as cylinders and solid or hollow cones. Hollow cones have also been fabricated to demonstrate the ability to build structures with sloped walls. Sintered samples have achieved 98% and 96% of their theoretical density for Al 2O3 and ZrB2, respectively. The dispersion of ZrB2 particles in an aqueous medium was investigated. In aqueous systems, the surface of ZrB2 consists of a thin layer of ZrO2 that controls the surface chemistry and surface charge. Measurements showed that the ZrB2 had an isoelectric point of pH = 4.7 and a maximum zeta potential of -50 mV at pH = 9. Either an ionic ammonium polyacrylate or a nonionic alkoxylated polyether increased the zeta potential of ZrB2 by as much as 60 mV, to -110 mV. Viscosity measurements were used to optimize dispersant concentrations. High solids loading (˜45 vol.% ZrB2) aqueous pastes were prepared. The pastes had viscosities of 40--50 Pa·s-1, which was acceptable for extrusion. The pastes were used to fabricate 3-D components from ZrB2. The microstructure of sintered ZrB2 consisted of equiaxed B4C with an average grain size of 4.3 mum and small equiaxed and large elongated ZrB2 grains with an average grain size of 40 mum. For longitude and transverse deposited samples, the elastic moduli were E = 435 and 417 GPa, the flexural strength sigmaf = 353

  11. Metallic Reactor Fuel Fabrication for SFR

    Energy Technology Data Exchange (ETDEWEB)

    Song, Hoon; Kim, Jong-Hwan; Ko, Young-Mo; Woo, Yoon-Myung; Kim, Ki-Hwan; Lee, Chan-Bock [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)


    The metal fuel for an SFR has such advantages such as simple fabrication procedures, good neutron economy, high thermal conductivity, excellent compatibility with a Na coolant, and inherent passive safety 1. U-Zr metal fuel for SFR is now being developed by KAERI as a national R and D program of Korea. The fabrication technology of metal fuel for SFR has been under development in Korea as a national nuclear R and D program since 2007. The fabrication process for SFR fuel is composed of (1) fuel slug casting, (2) loading and fabrication of the fuel rods, and (3) fabrication of the final fuel assemblies. Fuel slug casting is the dominant source of fuel losses and recycled streams in this fabrication process. Fabrication on the rod type metallic fuel was carried out for the purpose of establishing a practical fabrication method. Rod-type fuel slugs were fabricated by injection casting. Metallic fuel slugs fabricated showed a general appearance was smooth.

  12. SRF Cavity Fabrication and Materials

    CERN Document Server

    Singer, W


    The technological and metallurgical requirements of material for highgradient superconducting cavities are described. High-purity niobium, as the preferred metal for the fabrication of superconducting accelerating cavities, should meet exact specifications. The content of interstitial impurities such as oxygen, nitrogen, and carbon must be below 10μg/g. The hydrogen content should be kept below 2μg/g to prevent degradation of the Q-value under certain cool-down conditions. The material should be free of flaws (foreign material inclusions or cracks and laminations) that can initiate a thermal breakdown. Defects may be detected by quality control methods such as eddy current scanning and identified by a number of special methods. Conventional and alternative cavity fabrication methods are reviewed. Conventionally, niobium cavities are fabricated from sheet niobium by the formation of half-cells by deep drawing, followed by trim machining and Electron-Beam Welding (EBW). The welding of half-cells is a delicate...

  13. Stirling Microregenerators Fabricated and Tested (United States)

    Moran, Matthew E.


    A mesoscale Stirling refrigerator patented by the NASA Glenn Research Center is currently under development. This refrigerator has a predicted efficiency of 30 percent of Carnot and potential uses in electronics, sensors, optical and radiofrequency systems, microarrays, and microsystems. The mesoscale Stirling refrigerator is most suited to volume-limited applications that require cooling below the ambient or sink temperature. Primary components of the planar device include two diaphragm actuators that replace the pistons found in traditional-scale Stirling machines and a microregenerator that stores and releases thermal energy to the working gas during the Stirling cycle. Diaphragms are used to eliminate frictional losses and bypass leakage concerns associated with pistons, while permitting reversal of the hot and cold sides of the device during operation to allow precise temperature control. Three candidate microregenerators were fabricated under NASA grants for initial evaluation: two constructed of porous ceramic, which were fabricated by Johns Hopkins Applied Physics Laboratory, and one made of multiple layers of nickel and photoresist, which was fabricated by Polar Thermal Technologies. The candidate regenerators are being tested by Johns Hopkins Applied Physics in a custom piezoelectric-actuated test apparatus designed to produce the Stirling refrigeration cycle. In parallel with the regenerator testing, Johns Hopkins is using deep reactive ion etching to fabricate electrostatically driven, comb-drive diaphragm actuators. These actuators will drive the Stirling cycle in the prototype device. The top photograph shows the porous ceramic microregenerators. Two microregenerators were fabricated with coarse pores and two with fine pores. The bottom photograph shows the test apparatus parts for evaluating the microregenerators, including the layered nickel-and-photoresist regenerator fabricated using LIGA techniques.

  14. MQXFS1 Quadrupole Fabrication Report

    Energy Technology Data Exchange (ETDEWEB)

    Ambrosio, G. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Anerella, M. [Brookhaven National Lab. (BNL), Upton, NY (United States); Bossert, R. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Cavanna, E. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Cheng, D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Chlachidize, G. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Cooley, L. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Dietderich, D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Felice, H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ferracin, P. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Ghosh, A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Hafalia, R. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Holik, E. F. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Bermudez, S. Izquierdo [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Juchno, M. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Krave, S. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Marchevsky, M. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Muratore, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Nobrega, F. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Pan, H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Perez, J. C. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Pong, I. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Prestemon, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ravaioli, E. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Sabbi, G. L. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Santini, C. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Schmalzle, J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Stoynev, S. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Strauss, T. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Vallone, G. [European Organization for Nuclear Research (CERN), Geneva (Switzerland); Wanderer, P. [Brookhaven National Lab. (BNL), Upton, NY (United States); Wang, X. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Yu, M. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)


    This report presents the fabrication and QC data of MQXFS1, the first short model of the low-beta quadrupoles (MQXF) for the LHC High Luminosity Upgrade. It describes the conductor, the coils, and the structure that make the MQXFS1 magnet. Qualification tests and non-conformities are also presented and discussed. The fabrication of MQXFS1 was started before the finalization of conductor and coil design for MQXF magnets. Two strand design were used (RRP 108/127 and RRP 132/169). Cable and coil cross-sections were “first generation”.

  15. Fabrication Aware Form-finding

    DEFF Research Database (Denmark)

    Egholm Pedersen, Ole; Larsen, Niels Martin; Pigram, Dave


    This paper describes a design and construction method that combines two distinct material systems with fabrication aware form-finding and file-to-factory workflows. The method enables the fluent creation of complex materially efficient structures comprising high populations of geometrically unique...... parts. The first material system employs a novel rotated joint design to allow the structural tuning of quasi-reciprocal timber frame elements fabricated from multi-axis machined plywood sheet stock. The second em-loys discontinuous post-tensioning to assemble unique precast concrete components...

  16. Microfluidic fabrication of plasmonic microcapsules

    NARCIS (Netherlands)

    Wang, J.; Jin, Mingliang; Eijkel, Jan C.T.; van den Berg, Albert; Zhou, G.F.; Shui, L.L.


    This paper presents the plasmonic microcapsules with well-ordered nanoparticles embedded in polymer network fabricated by using a microfluidic device. The well-ordered nanoparticle arrays on the microcapsule form high-density uniform “hot-spots‿ with a deposited metal film, on which the localized

  17. Fabrication of metallic glass structures (United States)

    Cline, C.F.


    Amorphous metal powders or ribbons are fabricated into solid shapes of appreciable thickness by the application of compaction energy. The temperature regime wherein the amorphous metal deforms by viscous flow is measured. The metal powders or ribbons are compacted within the temperature regime.

  18. Fabrication of green polymeric membranes

    KAUST Repository

    Kim, Dooli


    Provided herein are methods of fabricating membranes using polymers with functionalized groups such as sulfone (e.g., PSf and PES), ether (e.g., PES), acrylonitrile (e.g., PAN), fluoride(e.g., pvdf and other fluoropolymers), and imide (e.g., extem) and ionic liquids. Also provided are membranes made by the provided methods.

  19. Transverse permeability of woven fabrics

    NARCIS (Netherlands)

    Grouve, Wouter Johannes Bernardus; Akkerman, Remko; Loendersloot, Richard; van den Berg, S.


    The transverse permeability is an essential input in describing the consolidation process of CETEX® laminates. A two-dimensional, finite difference based, Stokes flow solver has been developed to determine the mesoscopic permeability of arbitrary fabric structures. The use of a multigrid solver

  20. The Danish fabricated metal industry:

    DEFF Research Database (Denmark)

    Hansen, Teis


    . This is less the case for low-tech industries, but their economic importance continues to be large, however. It is thus interesting to analyse how they manage to remain competitive. The analysis focuses on a case study of the fabricated metal industry by identifying the innovation strategies followed by firms...

  1. Additives in fibers and fabrics. (United States)

    Barker, R H


    The additives and contaminants which occur in textile fibers vary widely, depending on the type of fiber and the pretreatment which it has received. Synthetic fibers such as nylon and polyester contain trace amounts of contaminants such as catalysts and catalyst deactivators which remain after the synthesis of the basic polymers. In addition, there are frequently a number of materials which are added to perform specific functions in almost all man-made fibers. Examples of these would include traces of metals or metal salts used as tracers for identification of specific lots of fiber, TiO2 or similar materials added as delustrants, and a host of organic species added for such special purposes as antistatic agents or flame retardants. There may also be considerable quantities of residual monomer or small oligomers dissolved in the polymer matrix. The situation becomes even more complex after the fibers are converted into fabric form. Numerous materials are applied at various stages of fabric preparation to act as lubricants, sizing agents, antistats, bleaches, and wetting agents to facilitate the processing, but these are normally removed before the fabric reaches the cutters of the ultimate consumers and therefore usually do not constitute potential hazards. However, there are many other chemical agents which are frequently added during the later stages of fabric preparation and which are not designed to be removed. Aside from dyes and printing pigments, the most common additive for apparel fabrics is a durable press treatment. This generally involves the use of materials capable of crosslinking cellulosics by reacting through such functions as N-methylolated amides or related compounds such as ureas and carbamates. These materials pose some potential hazards due to both the nitrogenous bases and the formaldehyde which they usually release. There is usually also some residual catalyst in fabrics which have received such treatments. Other types of chemical treatments

  2. Fabrication of elliptical SRF cavities (United States)

    Singer, W.


    The technological and metallurgical requirements of material for high-gradient superconducting cavities are described. High-purity niobium, as the preferred metal for the fabrication of superconducting accelerating cavities, should meet exact specifications. The content of interstitial impurities such as oxygen, nitrogen, and carbon must be below 10 μg g-1. The hydrogen content should be kept below 2 μg g-1 to prevent degradation of the quality factor (Q-value) under certain cool-down conditions. The material should be free of flaws (foreign material inclusions or cracks and laminations) that can initiate a thermal breakdown. Traditional and alternative cavity mechanical fabrication methods are reviewed. Conventionally, niobium cavities are fabricated from sheet niobium by the formation of half-cells by deep drawing, followed by trim machining and electron beam welding. The welding of half-cells is a delicate procedure, requiring intermediate cleaning steps and a careful choice of weld parameters to achieve full penetration of the joints. A challenge for a welded construction is the tight mechanical and electrical tolerances. These can be maintained by a combination of mechanical and radio-frequency measurements on half-cells and by careful tracking of weld shrinkage. The main aspects of quality assurance and quality management are mentioned. The experiences of 800 cavities produced for the European XFEL are presented. Another cavity fabrication approach is slicing discs from the ingot and producing cavities by deep drawing and electron beam welding. Accelerating gradients at the level of 35-45 MV m-1 can be achieved by applying electrochemical polishing treatment. The single-crystal option (grain boundary free) is discussed. It seems that in this case, high performance can be achieved by a simplified treatment procedure. Fabrication of the elliptical resonators from a seamless pipe as an alternative is briefly described. This technology has yielded good

  3. Novel fabric pressure sensors: design, fabrication, and characterization (United States)

    Wang, Yangyong; Hua, Tao; Zhu, Bo; Li, Qiao; Yi, Weijing; Tao, Xiaoming


    Soft and pliable pressure sensors are essential elements in wearable electronics which have wide applications in modern daily lives. This paper presents a family of fabric pressure sensors made by sandwiching a piece of resistive fabric strain sensing element between two tooth-structured layers of soft elastomers. The pressure sensors are capable of measuring pressure from 0 to 2000 kPa, covering the whole range of human-machine interactions. A pressure sensitivity of up to 2.98 × 10 - 3 kPa - 1 was obtained. Theoretical modeling was conducted based on an energy method to predict the load-displacement relationship for various sensor configurations. By adjusting the Young's modulus of the two conversion layers, as well as the geometrical dimensions, the measurement ranges, and sensitivities of the sensors can be quantitatively determined. The sensors are being used for pressure measurements between the human body and garments, shoes, beds, and chairs.

  4. Preparation of activated carbon fabrics from cotton fabric precursor (United States)

    Salehi, R.; Dadashian, F.; Abedi, M.


    The preparation of activated carbon fabrics (ACFs) from cotton fabric was performed by chemical activation with phosphoric acid (H3PO4). The operation conditions for obtaining the ACFs with the highest the adsorption capacity and process yield, proposed. Optimized conditions were: impregnation ratio of 2, the rate of temperature rising of 7.5 °C min‑1, the activation temperature of 500 °C and the activation time of 30 min. The ACFs produced under optimized conditions was characterized by scanning electron microscopy (SEM) and energy dispersive X-ray spectroscopy (EDX). The surface area and pore volume of carbon nanostructures was characterized by BET nitrogen adsorption isotherm at 77 °K. The pore size distribution calculated from the desorption branch according to BJH method. The iodine number of the prepared ACFs was determined by titration at 30 °C based on the ASTM D4607-94. The results showed the improvement of porous structure, fabric shape, surface area (690 m2/g), total pore volume (0.3216 cm3/g), and well-preserved fibers integrity.

  5. Nylon fabric reinforced natural rubber compound (United States)

    Kamal, Mazlina Mustafa; Ismail, Ismaliza


    Rubber fabric coated is a unique rubber-textile composite, in which technical textile acts as reinforcing material and strength providing material. In rubber textile composite, rubber to fabric adhesion plays the most critical role for determining assembly process and ultimate strength of product. A vulcanisable adhesive for rubber to fabric fabrication of composite material was developed which compatible with rubber as well as fabric. Evaluation of bonding system with respect to peel strength, shear adhesion strength and weave pattern of fabrics were the major determining criteria for selection and optimization of fabric for rubber hose application. Thus adhesive Cohedure with characteristics of high adhesive strength in Natural Rubber Polyester Fabric compound has been developed.

  6. Fabric quality issues related to apparel merchandising

    CSIR Research Space (South Africa)

    Das, Sonali


    Full Text Available The objectives of this study are to develop an understanding of fabric quality related issues and research gaps relevant to apparel manufacturing and merchandising within the South African context. The specific focus is on fabric objective...

  7. Ballistic Response of Fabrics: Model and Experiments (United States)

    Orphal, Dennis L.; Walker Anderson, James D., Jr.


    Walker (1999)developed an analytical model for the dynamic response of fabrics to ballistic impact. From this model the force, F, applied to the projectile by the fabric is derived to be F = 8/9 (ET*)h^3/R^2, where E is the Young's modulus of the fabric, T* is the "effective thickness" of the fabric and equal to the ratio of the areal density of the fabric to the fiber density, h is the displacement of the fabric on the axis of impact and R is the radius of the fabric deformation or "bulge". Ballistic tests against Zylon^TM fabric have been performed to measure h and R as a function of time. The results of these experiments are presented and analyzed in the context of the Walker model. Walker (1999), Proceedings of the 18th International Symposium on Ballistics, pp. 1231.

  8. Advanced fabrication of hyperbolic metamaterials

    DEFF Research Database (Denmark)

    Shkondin, Evgeniy; Sukham, Johneph; Panah, Mohammad Esmail Aryaee


    Hyperbolic metamaterials can provide unprecedented properties in accommodation of high-k (high wave vector) waves and enhancement of the optical density of states. To reach such performance the metamaterials have to be fabricated with as small imperfections as possible. Here we report on our...... advances in two approaches in fabrication of optical metamaterials. We deposit ultrathin ultrasmooth gold layers with the assistance of organic material (APTMS) adhesion layer. The technology supports the stacking of such layers in a multiperiod construction with alumina spacers between gold films, which...... is expected to exhibit hyperbolic properties in the visible range. As the second approach we apply the atomic layer deposition technique to arrange vertical alignment of layers or pillars of heavily doped ZnO or TiN, which enables us to produce hyperbolic metamaterials for the near- and mid-infrared ranges....

  9. Structural colors, cosmetics, and fabrics (United States)

    Dushkina, Natalia; Lakhtakia, Akhlesh


    Structural colors are non-pigment colors that originate from the scattering of light from ordered microstructures, thin films, and even irregular arrays of scatterers. Examples include the flashing sparks of colors in opals and the brilliant hues of some butterflies such as Morpho rhetenor. Structural colors arise in nature from one or more of a palette of physical mechanisms that are now understood quite well and can be implemented industrially to produce structurally colored paints, fabrics, and cosmetics.

  10. Fabricated Helicopter Transmission Housing Analysis (United States)


    rotor head, rotor blades, swashplate assembly, main rotor controls, and internal gearing. Flight loads on the fabricated housing were determined for...The servo support brackets react induced loads from the swashplate on the servos. A swashplate guide is mounted to the top of the upper housing and...serves to locate the swashplate and react any induced side loads. The scissor bracket connects the upper main housing and the stationary swashplate

  11. Nanocarbon materials fabricated using plasmas (United States)

    Hatakeyama, Rikizo


    Since the discovery of fullerenes more than three decades ago, new kinds of nanoscale materials of carbon allotropes called "nanocarbons" have so far been discovered or synthesized at successive intervals as cases such as carbon nanotubes, carbon nanohorns, graphene, carbon nanowalls, and a carbon nanobelt, while nanodiamonds were actually discovered before then. Their attractively excellent mechanical, physical, and chemical properties have driven researchers to continuously create one of the hottest frontiers in materials science and technology. While plasma states have often been involved in their discovery, on the other hand, plasma-based approaches to this exciting field originally hold promising and enormous potentials for advancing and expanding industrial/biomedical applications of nanocarbons of great diversity. This article provides an extensive overview on plasma-fabricated nanocarbon materials, where the term "fabrication" is defined as synthesis, functionalization, and assembly of devices to cover a wide range of issues associated with the step-by-step plasma processes. Specific attention has been paid to the comparative examination between plasma-based and non-plasma methods for fabricating the nanocarobons with an emphasis on the advantages of plasma processing, such as low-temperature/large-scale fabrication and diversity-carrying structure controllability. The review ends with current challenges and prospects including a ripple effect of the nanocarbon studies on the development of related novel nanomaterials such as transition metal dichalcogenides. It contains not only the latest progress in the field for cutting-edge scientists and engineers, but also the introductory guidance to non-specialists such as lower-class graduate students.

  12. Flexible Metal-Fabric Radiators (United States)

    Cross, Cynthia; Nguyen, Hai D.; Ruemmele, Warren; Andish, Kambiz K.; McCalley, Sean


    Flexible metal-fabric radiators have been considered as alternative means of dissipating excess heat from spacecraft and space suits. The radiators also may be useful in such special terrestrial applications as rejecting heat from space-suit-like protective suits worn in hot work environments. In addition to flexibility and consequent ease of deployment and installation on objects of varying sizes and shapes, the main advantages of these radiators over conventional rigid radiators are that they weigh less and occupy less volume for a given amount of cooling capacity. A radiator of this type includes conventional stainless-steel tubes carrying a coolant fluid. The main radiating component consists of a fabric of interwoven aluminum-foil strips bonded to the tubes by use of a proprietary process. The strip/tube bonds are strong and highly thermally conductive. Coolant is fed to and from the tubes via flexible stainless-steel manifolds designed to accommodate flexing of, and minimize bending forces on, the fabric. The manifolds are sized to minimize pressure drops and distribute the flow of coolant evenly to all the tubes. The tubes and manifolds are configured in two independent flow loops for operational flexibility and protective redundancy.

  13. Fabricating customized hydrogel contact lens (United States)

    Childs, Andre; Li, Hao; Lewittes, Daniella M.; Dong, Biqin; Liu, Wenzhong; Shu, Xiao; Sun, Cheng; Zhang, Hao F.


    Contact lenses are increasingly used in laboratories for in vivo animal retinal imaging and pre-clinical studies. The lens shapes often need modification to optimally fit corneas of individual test subjects. However, the choices from commercially available contact lenses are rather limited. Here, we report a flexible method to fabricate customized hydrogel contact lenses. We showed that the fabricated hydrogel is highly transparent, with refractive indices ranging from 1.42 to 1.45 in the spectra range from 400 nm to 800 nm. The Young’s modulus (1.47 MPa) and hydrophobicity (with a sessile drop contact angle of 40.5°) have also been characterized experimentally. Retinal imaging using optical coherence tomography in rats wearing our customized contact lenses has the quality comparable to the control case without the contact lens. Our method could significantly reduce the cost and the lead time for fabricating soft contact lenses with customized shapes, and benefit the laboratorial-used contact lenses in pre-clinical studies.

  14. Robust fabric substrates for photonic textile applications

    NARCIS (Netherlands)

    Van Pieterson, L.; Bouten, P.C.P.; Kriege, J.C.; Bhattacharya, R.


    A fabric substrate is described for electronic textile with robust interwoven connections between the conductive yarns in it. The fabric's robustness, as a function of the electrical reliability of its conductive yarn connections, is shown to hold over large deformations.This fabric is then used to

  15. Shock wave fabricated ceramic-metal nozzles

    NARCIS (Netherlands)

    Carton, E.P.; Stuivinga, M.E.C.; Keizers, H.L.J.; Verbeek, H.J.; Put, P.J. van der


    Shock compaction was used in the fabrication of high temperature ceramic-based materials. The materials' development was geared towards the fabrication of nozzles for rocket engines using solid propellants, for which the following metal-ceramic (cermet) materials were fabricated and tested: B4C-Ti

  16. Fabrication technology for ODS Alloy MA957

    Energy Technology Data Exchange (ETDEWEB)

    ML Hamilton; DS Gelles; RJ Lobsinger; MM Paxton; WF Brown


    A successful fabrication schedule has been developed at Carpenter Technology Corporation for the production of MA957 fuel and blanket cladding. Difficulties with gun drilling, plug drawing and recrystallization were overcome to produce a pilot lot of tubing. This report documents the fabrication efforts of two qualified vendors and the support studies performed at WHC to develop the fabrication-schedule.

  17. High-Thermal-Conductivity Fabrics (United States)

    Chibante, L. P. Felipe


    Heat management with common textiles such as nylon and spandex is hindered by the poor thermal conductivity from the skin surface to cooling surfaces. This innovation showed marked improvement in thermal conductivity of the individual fibers and tubing, as well as components assembled from them. The problem is centered on improving the heat removal of the liquid-cooled ventilation garments (LCVGs) used by astronauts. The current design uses an extensive network of water-cooling tubes that introduces bulkiness and discomfort, and increases fatigue. Range of motion and ease of movement are affected as well. The current technology is the same as developed during the Apollo program of the 1960s. Tubing material is hand-threaded through a spandex/nylon mesh layer, in a series of loops throughout the torso and limbs such that there is close, form-fitting contact with the user. Usually, there is a nylon liner layer to improve comfort. Circulating water is chilled by an external heat exchanger (sublimator). The purpose of this innovation is to produce new LCVG components with improved thermal conductivity. This was addressed using nanocomposite engineering incorporating high-thermalconductivity nanoscale fillers in the fabric and tubing components. Specifically, carbon nanotubes were added using normal processing methods such as thermoplastic melt mixing (compounding twin screw extruder) and downstream processing (fiber spinning, tubing extrusion). Fibers were produced as yarns and woven into fabric cloths. The application of isotropic nanofillers can be modeled using a modified Nielsen Model for conductive fillers in a matrix based on Einstein s viscosity model. This is a drop-in technology with no additional equipment needed. The loading is limited by the ability to maintain adequate dispersion. Undispersed materials will plug filtering screens in processing equipment. Generally, the viscosity increases were acceptable, and allowed the filled polymers to still be

  18. Micro-fabricated all optical pressure sensors

    DEFF Research Database (Denmark)

    Havreland, Andreas Spandet; Petersen, Søren Dahl; Østergaard, Christian


    Optical pressure sensors can operate in certain harsh application areas where the electrical pressure sensors cannot. However, the sensitivity is often not as good for the optical sensors. This work presents an all optical pressure sensor, which is fabricated by micro fabrication techniques, where...... the sensitivity can be tuned in the fabrication process. The developed sensor design, simplifies the fabrication process leading to a lower fabrication cost, which can make the all optical pressure sensors more competitive towards their electrical counterpart. The sensor has shown promising results and a linear...

  19. Design Thinking for Digital Fabrication in Education

    DEFF Research Database (Denmark)

    Smith, Rachel Charlotte; Iversen, Ole Sejer; Hjorth, Mikkel


    In this paper, we argue that digital fabrication in education may benefit from design thinking, to foster a more profound understanding of digital fabrication processes among students. Two related studies of digital fabrication in education are presented in the paper. In an observational study we...... found that students (eleven to fifteen) lacked an understanding of the complexity of the digital fabrication process impeding on the potentials of digital fabrication in education. In a second explorative research through design study, we investigated how a focus on design thinking affected the students......’ performance in digital fabrication processes. Our findings indicate that design thinking can provide students with a general understanding of the creative and complex process through which artifacts and futures emerge in processes of digital fabrication....

  20. Properties of honeycomb polyester knitted fabrics (United States)

    Feng, A. F.


    The properties of honeycomb polyester weft-knitted fabrics were studied to understand their advantages. Seven honeycomb polyester weft-knitted fabrics and one common polyester weft-knitted fabric were selected for testing. Their bursting strengths, fuzzing and pilling, air permeability, abrasion resistance and moisture absorption and perspiration were studied. The results show that the honeycomb polyester weft-knitted fabrics have excellent moisture absorption and liberation. The smaller their thicknesses and area densities are, the better their moisture absorption and liberation will be. Their anti-fuzzing and anti-pilling is good, whereas their bursting strengths and abrasion resistance are poorer compared with common polyester fabric's. In order to improve the hygroscopic properties of the fabrics, the proportion of the honeycomb microporous structure modified polyester in the fabrics should not be less than 40%.

  1. Porosity Prediction of Plain Weft Knitted Fabrics

    Directory of Open Access Journals (Sweden)

    Muhammad Owais Raza Siddiqui


    Full Text Available Wearing comfort of clothing is dependent on air permeability, moisture absorbency and wicking properties of fabric, which are related to the porosity of fabric. In this work, a plug-in is developed using Python script and incorporated in Abaqus/CAE for the prediction of porosity of plain weft knitted fabrics. The Plug-in is able to automatically generate 3D solid and multifilament weft knitted fabric models and accurately determine the porosity of fabrics in two steps. In this work, plain weft knitted fabrics made of monofilament, multifilament and spun yarn made of staple fibers were used to evaluate the effectiveness of the developed plug-in. In the case of staple fiber yarn, intra yarn porosity was considered in the calculation of porosity. The first step is to develop a 3D geometrical model of plain weft knitted fabric and the second step is to calculate the porosity of the fabric by using the geometrical parameter of 3D weft knitted fabric model generated in step one. The predicted porosity of plain weft knitted fabric is extracted in the second step and is displayed in the message area. The predicted results obtained from the plug-in have been compared with the experimental results obtained from previously developed models; they agreed well.

  2. Fabrication and Calibration of FORTIS (United States)

    Fleming, Brian T.; McCandliss, Stephan R.; Kaiser, Mary Elizabeth; Kruk, Jeffery; Feldman, Paul D.; Kutyrev, Alexander S.; Li, Mary J.; Rapchun, David A.; Lyness, Eric; Moseley, S. H.; hide


    The Johns Hopkins University sounding rocket group is entering the final fabrication phase of the Far-ultraviolet Off Rowland-circle Telescope for Imaging and Spectroscopy (FORTIS); a sounding rocket borne multi-object spectro-telescope designed to provide spectral coverage of 43 separate targets in the 900 - 1800 Angstrom bandpass over a 30' x 30' field-of-view. Using "on-the-fly" target acquisition and spectral multiplexing enabled by a GSFC microshutter array, FORTIS will be capable of observing the brightest regions in the far-UV of nearby low redshift (z approximately 0.002 - 0.02) star forming galaxies to search for Lyman alpha escape, and to measure the local gas-to-dust ratio. A large area (approximately 45 mm x 170 mm) microchannel plate detector built by Sensor Sciences provides an imaging channel for targeting flanked by two redundant spectral outrigger channels. The grating is ruled directly onto the secondary mirror to increase efficiency. In this paper, we discuss the recent progress made in the development and fabrication of FORTIS, as well as the results of early calibration and characterization of our hardware, including mirror/grating measurements, detector performance, and early operational tests of the micro shutter arrays.

  3. Polymer micromold and fabrication process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, A.P.; Northrup, M.A.; Ahre, P.E.; Dupuy, P.C.


    A mold assembly is disclosed with micro-sized features in which the hollow portion thereof is fabricated from a sacrificial mandrel which is surface treated and then coated to form an outer shell. The sacrificial mandrel is then selectively etched away leaving the outer shell as the final product. The sacrificial mandrel is fabricated by a precision lathe, for example, so that when removed by etching the inner or hollow area has diameters as small as 10`s of micros ({micro}m). Varying the inside diameter contours of the mold can be accomplished with specified ramping slopes formed on the outer surface of the sacrificial mandrel, with the inside or hollow section being, for example, 275 {micro}m in length up to 150 {micro}m in diameter within a 6 mm outside diameter (o.d.) mold assembly. The mold assembly itself can serve as a micronozzle or microneedle, and plastic parts, such as microballoons for angioplasty, polymer microparts, and microactuators, etc., may be formed within the mold assembly. 6 figs.

  4. Polymer micromold and fabrication process

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Abraham P. (1428 Whitecliff Way, Walnut Creek, CA 94596); Northrup, M. Allen (923 Creston Rd., Berkeley, CA 94708); Ahre, Paul E. (1299 Gonzaga Ct., Livermore, CA 94550); Dupuy, Peter C. (1736 Waldo Ct., Modesto, CA 95358)


    A mold assembly with micro-sized features in which the hollow portion thereof is fabricated from a sacrificial mandrel which is surface treated and then coated to form an outer shell. The sacrificial mandrel is then selectively etched away leaving the outer shell as the final product. The sacrificial mandrel is fabricated by a precision lathe, for example, so that when removed by etching the inner or hollow area has diameters as small as 10's of micros (.mu.m). Varying the inside diameter contours of the mold can be accomplished with specified ramping slopes formed on the outer surface of the sacrificial mandrel, with the inside or hollow section being, for example, 275 .mu.m in length up to 150 .mu.m in diameter within a 6 mm outside diameter (o.d.) mold assembly. The mold assembly itself can serve as a micronozzle or microneedle, and plastic parts, such as microballoons for angioplasty, polymer microparts, and microactuators, etc., may be formed within the mold assembly.

  5. Fabrication of Yb-123 Tapes

    Energy Technology Data Exchange (ETDEWEB)

    Athur, S.; Balachandran, U.; Salama, K.


    While Bi-2223 tapes have been the workhorses of the superconductor industry, their poor performance in applied magnetic fields restrict their use to below 30 K. Melt-processing of Ag-clad Yb-123 PIT tapes offers a simple and scalable technique for fabricating long-length HTS conductors capable of being used at 77 K. Under reduced oxygen partial pressure, the peritectic temperature of Yb-123 is below the melting point of Ag, and this facilitates the adaptation of melt-texturing methods for fabricating these tapes. The effect of melt-processing temperature on current density was also explored; a temperature of 965 C yielded optimal critical current values. The critical current density achieved at 4.2 K was 20,000 A/cm{sup 2}, corresponding to a critical current of 52 A. Based on the above results, an optimal processing zone for melt-processing of Ag-clad Yb-123 tapes was determined. These results hold promise for melt-processing of Ag-clad Yb-123 tapes as an alternative to Bi-2223 PIT technology.

  6. Integrated Recycling Test Fuel Fabrication

    Energy Technology Data Exchange (ETDEWEB)

    R.S. Fielding; K.H. Kim; B. Grover; J. Smith; J. King; K. Wendt; D. Chapman; L. Zirker


    The Integrated Recycling Test is a collaborative irradiation test that will electrochemically recycle used light water reactor fuel into metallic fuel feedstock. The feedstock will be fabricated into a metallic fast reactor type fuel that will be irradiation tested in a drop in capsule test in the Advanced Test Reactor on the Idaho National Laboratory site. This paper will summarize the fuel fabrication activities and design efforts. Casting development will include developing a casting process and system. The closure welding system will be based on the gas tungsten arc burst welding process. The settler/bonder system has been designed to be a simple system which provides heating and controllable impact energy to ensure wetting between the fuel and cladding. The final major pieces of equipment to be designed are the weld and sodium bond inspection system. Both x-radiography and ultrasonic inspection techniques have been examine experimentally and found to be feasible, however the final remote system has not been designed. Conceptual designs for radiography and an ultrasonic system have been made.

  7. Versatile superamphiphobic cotton fabrics fabricated by coating with SiO2/FOTS (United States)

    Li, Deke; Guo, Zhiguang


    A multifunctional superamphiphobic cotton fabric was fabricated by coating silica nanoparticles on the cotton fabric surface and further modification by 1H,1H,2H,2H-perfluorooctyltrichlorosilane (FOTS). The fluctuant woven fabric and the fluffy spherical SiO2 nanoparticles constructed a dual micro/nano-structures. The surface free energy of the fabric composite was reduced by FOTS modifier. The interplay of the structured and perfluorinated SiO2 nanoparticles could not only endow the fabric highly liquid repellent ability, but could also to enhance the coating stability. The prepared cotton fabrics exhibited high liquid repellency to water, colza oil and n-hexadecane with lower surface tension, showing a contact angle of 158°, 152°, and 153°, respectively. The results demonstrated that superamphiphobic cotton fabric possessed desirable chemical and mechanical durability, self-cleaning and self-healing property, the robust and multifunctional fabric would find innovative opportunities for practical applications.

  8. Design and fabrication of SGS plutonium standards

    Energy Technology Data Exchange (ETDEWEB)

    Hsue, S.T.; Simmonds, S.M.; Longmire, V.L.; Long, S.M.


    This paper describes our experience of fabricating four sets of plutonium segmented gamma scanner (SGS) can standards. The fabrication involves careful planning, meticulous execution in weighing the plutonium oxide while minimizing contamination, chemical analyses by three different national laboratories to get accurate and independent plutonium concentrations, vertical scanning to assure mixing of the plutonium and the diluent, and finally the nondestructive verification measurement. By following these steps, we successfully fabricated 4 sets or 20 SGS can standards. 4 refs., 5 figs., 3 tabs.

  9. Update On Monolithic Fuel Fabrication Development

    Energy Technology Data Exchange (ETDEWEB)

    C. R Clark; J. M. Wight; G. C. Knighton; G. A. Moore; J. F. Jue


    Efforts to develop a viable monolithic research reactor fuel plate have continued at Idaho National Laboratory. These efforts have concentrated on both fabrication process refinement and scale-up to produce full sized fuel plates. Advancements have been made in the production of U-Mo foil including full sized foils. Progress has also been made in the friction stir welding and transient liquid phase bonding fabrication processes resulting in better bonding, more stable processes and the ability to fabricate larger fuel plates.

  10. Nanocrystal thin film fabrication methods and apparatus

    Energy Technology Data Exchange (ETDEWEB)

    Kagan, Cherie R.; Kim, David K.; Choi, Ji-Hyuk; Lai, Yuming


    Nanocrystal thin film devices and methods for fabricating nanocrystal thin film devices are disclosed. The nanocrystal thin films are diffused with a dopant such as Indium, Potassium, Tin, etc. to reduce surface states. The thin film devices may be exposed to air during a portion of the fabrication. This enables fabrication of nanocrystal-based devices using a wider range of techniques such as photolithography and photolithographic patterning in an air environment.

  11. Crimp-Imbalanced Protective (CRIMP) Fabrics (United States)


    Spectra, and Zylon fabrics for enhancing the performance of lightweight fragmentation barriers used in commercial aircraft. Impact tests were conducted...on the fabric specimens as well as on aluminum 2024-T3 skin for baseline purposes. The Kevlar, Spectra, and Zylon outperformed the aluminum on an...areal density basis by 6 to 1, 7 to 1, and 12 to 1, respectively. Additional tests were performed on Zylon fabric specimens to compare the effects of

  12. Plasmonic nanoparticles: Towards the fabrication of biosensors (United States)

    Shen, Hui


    Au and Ag nanoparticles are mainly employed in the fabrication of biosensors owing to their unique optical properties compared to other noble metal nanoparticles. Many biosensors are fabricated for the rapid detection of different analytes such as organic and inorganic molecules, biomolecules like DNA, proteins, biotoxins and pathogens. In this mini review we mainly discuss on the usage of Au and Ag nanoparticles for the fabrication of colorimetric, SERS and two photon based photoluminescence biosensors.

  13. Dyeing of hydrophobic fabrics with disperse dyes

    Directory of Open Access Journals (Sweden)



    Full Text Available A series of disperse dyes has been synthesized by diazotisation of 2,6-dibromo-4-nitroaniline and coupled with various N-arylmaleimides. The dyes were characterized by IR spectral studies, visible absorption spectroscopy and elemental analysis. All the dyes were applied as disperse dyes on nylon, cellulose triacetate and polyester fabrics. These dyeswere found to give yellowish orange to deep brown shades with very good depth, levelness and brightness on different fabrics. The percentage dye bath exhaustion and fixation on fabrics were found to be very good. The light, washing, rubbing, perspiration and sublimation fastness properties of the dyed fabrics were found to be good to excellent.

  14. Propulsion Design with Freeform Fabrication Project (United States)

    National Aeronautics and Space Administration — Propulsion Design with Freeform Fabrication (PDFF) will develop and implement a novel design methodology that leverages the rapidly evolving Solid Freeform...

  15. Photolithography and Micro-Fabrication/ Packaging Laboratories (United States)

    Federal Laboratory Consortium — The Photolithography and Micro-Fabrication/Packaging laboratories provide research level semiconductor processing equipment and facilities that do not require a full...

  16. Fabrication of Metallic Hollow Nanoparticles (United States)

    Kim, Jae-Woo (Inventor); Choi, Sr., Sang H. (Inventor); Lillehei, Peter T. (Inventor); Chu, Sang-Hyon (Inventor); Park, Yeonjoon (Inventor); King, Glen C. (Inventor); Elliott, James R. (Inventor)


    Metal and semiconductor nanoshells, particularly transition metal nanoshells, are fabricated using dendrimer molecules. Metallic colloids, metallic ions or semiconductors are attached to amine groups on the dendrimer surface in stabilized solution for the surface seeding method and the surface seedless method, respectively. Subsequently, the process is repeated with additional metallic ions or semiconductor, a stabilizer, and NaBH.sub.4 to increase the wall thickness of the metallic or semiconductor lining on the dendrimer surface. Metallic or semiconductor ions are automatically reduced on the metallic or semiconductor nanoparticles causing the formation of hollow metallic or semiconductor nanoparticles. The void size of the formed hollow nanoparticles depends on the dendrimer generation. The thickness of the metallic or semiconductor thin film around the dendrimer depends on the repetition times and the size of initial metallic or semiconductor seeds.

  17. Remote Microelectronics Fabrication Laboratory MEFLab

    Directory of Open Access Journals (Sweden)

    Jan Machotka


    Full Text Available Over the last decade, there has been a move towards using remote laboratories in engineering education. The majority of these laboratories are static, involving limited user-controlled mechanical movements. The University of South Australia has developed such a laboratory, called NetLab that has been successfully utilized for teaching both on-campus and transnational programs in electrical and electronics engineering. Following this success, we are now developing a remote laboratory for microelectronic fabrication, MEFLab. The first stage of the development is a remote laboratory for visual inspection and testing of electronic circuits directly on the silicon wafer under a microscope which is normally conducted in a cleanroom. The major challenge of this project is the accurate positioning of micro-probes remotely over the internet. This paper presents the details of the setup of this new remote laboratory, with a particular emphasis on the development of the hardware, software and graphical user interface.


    Energy Technology Data Exchange (ETDEWEB)

    Dunn, K.; Louthan, M.; Rawls, G.; Sindelar, R.; Zapp, P.; Mcclard, J.


    The multi-barrier 3013 container used to package plutonium-bearing materials is robust and thereby highly resistant to identified degradation modes that might cause failure. The only viable degradation mechanisms identified by a panel of technical experts were pressurization within and corrosion of the containers. Evaluations of the container materials and the fabrication processes and resulting residual stresses suggest that the multi-layered containers will mitigate the potential for degradation of the outer container and prevent the release of the container contents to the environment. Additionally, the ongoing surveillance programs and laboratory studies should detect any incipient degradation of containers in the 3013 storage inventory before an outer container is compromised.

  19. Fuel Fabrication Capability Research and Development Plan

    Energy Technology Data Exchange (ETDEWEB)

    Senor, David J.; Burkes, Douglas


    The purpose of this document is to provide a comprehensive review of the mission of the Fuel Fabrication Capability (FFC) within the Global Threat Reduction Initiative (GTRI) Convert Program, along with research and development (R&D) needs that have been identified as necessary to ensuring mission success. The design and fabrication of successful nuclear fuels must be closely linked endeavors.

  20. Fabrication of photonic crystals and Nanocavities

    NARCIS (Netherlands)

    Woldering, L.A.


    The fabrication of three-dimensional inverse woodpile photonic crystals is highly desirable because of their predicted large photonic band gap, their conceptual ease of fabrication, and their robustness to withstand deviations from the ideal geometry that are intrinsic to nanofabrication. In this

  1. Fabrication of Polymer Optical Fibre (POF) Gratings (United States)

    Luo, Yanhua; Yan, Binbin; Zhang, Qijin; Peng, Gang-Ding; Wen, Jianxiang; Zhang, Jianzhong


    Gratings inscribed in polymer optical fibre (POF) have attracted remarkable interest for many potential applications due to their distinctive properties. This paper overviews the current state of fabrication of POF gratings since their first demonstration in 1999. In particular we summarize and discuss POF materials, POF photosensitivity, techniques and issues of fabricating POF gratings, as well as various types of POF gratings. PMID:28273844

  2. Fabrication, Morphological and Optoelectronic Properties of ...

    African Journals Online (AJOL)

    We report on the fabrication and characterization of MSM photodetector. We investigated the surface morphological and the structural properties of the porous silicon by optical microscopy, atomic force microscope (AFM) and X-ray diffraction. The metal–semiconductor–metal photodetector were fabricated by using Sb as ...

  3. Thermoplastic microcantilevers fabricated by nanoimprint lithography

    DEFF Research Database (Denmark)

    Greve, Anders; Keller, Stephan Urs; Vig, Asger Laurberg


    Nanoimprint lithography has been exploited to fabricate micrometre-sized cantilevers in thermoplastic. This technique allows for very well defined microcantilevers and gives the possibility of embedding structures into the cantilever surface. The microcantilevers are fabricated in TOPAS and are up...

  4. Thermomechanical properties of woven fabric composites

    NARCIS (Netherlands)

    Akkerman, Remko; de Vries, R.S.


    The in-plane thermo-elastic behaviour of woven fabric reinforced composites is analysed using a combination of published micromechanics and finite element techniques. The repetitive unit of an arbitrary woven fabric composite is divided into elements of which the thermo-elastic properties are

  5. Patterned Woven Fabrics in Lithuanian Folk Skirts

    Directory of Open Access Journals (Sweden)



    Full Text Available In the article 258 Lithuanian folk skirts from National M. K. Čiurlionis Museum of Art and 85 skirts from Lithuanian Open Air Museum are investigated. The weaves and plans of weave of skirts fabrics are made. Also the composing of plans of weave is analysed in aspect of segment, ornament and symmetry group of patterned fabric weave. Also the symmetry groups of Lithuanian folk skirts fabrics and their distribution according to the fabric weave are analysed. The tendencies of symmetry groups and peculiarities of composing of plans of weave can help to recreate the reconstructions of authentic folk fabrics. DOI:

  6. Moisture management properties of Cupro knitted fabrics (United States)

    Durur, G.; Oner, E.; Gunduz, G.


    On the purpose of analysing the moisture management behaviour of Cupro blend knitted fabrics made of Ne 40/1 and Ne 56/1 cotton/Cupro blend yarns, which have single jersey, 1x1 rib and interlock knitting types were systematically produced. Multi-dimensional liquid transport properties of the produced fabric were measured on the Moisture Management Tester (MMT). The air permeability and some structural properties of the fabrics were also measured, and the results were evaluated taking into account moisture management properties. According to results, it is observed that moisture management capacity and permeability of Cupro blends produced from finer yarns were higher than those of fabrics from coarse count yarns. Generally, Cupro blend knitted fabrics showed good moisture management properties.

  7. Fabricating 3D figurines with personalized faces. (United States)

    Tena, J Rafael; Mahler, Moshe; Beeler, Thabo; Grosse, Max; Hengchin Yeh; Matthews, Iain


    We present a semi-automated system for fabricating figurines with faces that are personalised to the individual likeness of the customer. The efficacy of the system has been demonstrated by commercial deployments at Walt Disney World Resort and Star Wars Celebration VI in Orlando Florida. Although the system is semi automated, human intervention is limited to a few simple tasks to maintain the high throughput and consistent quality required for commercial application. In contrast to existing systems that fabricate custom heads that are assembled to pre-fabricated plastic bodies, our system seamlessly integrates 3D facial data with a predefined figurine body into a unique and continuous object that is fabricated as a single piece. The combination of state-of-the-art 3D capture, modelling, and printing that are the core of our system provide the flexibility to fabricate figurines whose complexity is only limited by the creativity of the designer.

  8. Influence of Fabric Parameters on Thermal Comfort Performance of Double Layer Knitted Interlock Fabrics

    Directory of Open Access Journals (Sweden)

    Afzal Ali


    Full Text Available The aim of this study was to analyse the effects of various fabric parameters on the thermal resistance, thermal conductivity, thermal transmittance, thermal absorptivity and thermal insulation of polyester/cotton double layer knitted interlock fabrics. It was found that by increasing fibre content with higher specific heat increases the thermal insulation while decreases the thermal transmittance and absorptivity of the fabric. It was concluded that double layer knitted fabrics developed with higher specific heat fibres, coarser yarn linear densities, higher knitting loop length and fabric thickness could be adequately used for winter clothing purposes.

  9. Fabrication of microfluidic integrated biosensor (United States)

    Adam, Tijjani; Dhahi, Th S.; Mohammed, Mohammed; Hashim, U.; Noriman, N. Z.; Dahham, Omar S.


    An event of miniaturizing for sensor systems to carry out biological diagnostics are gaining wade spread acceptance. The system may contain several different sensor units for the detection of specific analyte, the analyte to be detected might be any kind of biological molecules (DNA, mRNA or proteins) or chemical substances. In most cases, the detection is based on receptor-ligand binding like DNA hybridization or antibody-antigen interaction, achieving this on a nanostructure. DNA or protein must be attached to certain locations within the structure. Critical for this is to have a robust binding chemistry to the surface in the microstructure. Here we successfully designed and fabricated microfluidics element for passive fluid delivery into polysilicon Nanowire sensing domain, we further demonstrated a very simple and effective way of integrating the two devices to give full functionalities of laboratory on a single chip. The sensing element was successfully surface modified and tested on real biomedical clinical sample for evaluation and validation.

  10. Plastron Respiration Using Commercial Fabrics

    Directory of Open Access Journals (Sweden)

    Shaun Atherton


    Full Text Available A variety of insect and arachnid species are able to remain submerged in water indefinitely using plastron respiration. A plastron is a surface-retained film of air produced by surface morphology that acts as an oxygen-carbon dioxide exchange surface. Many highly water repellent and hydrophobic surfaces when placed in water exhibit a silvery sheen which is characteristic of a plastron. In this article, the hydrophobicity of a range of commercially available water repellent fabrics and polymer membranes is investigated, and how the surface of the materials mimics this mechanism of underwater respiration is demonstrated allowing direct extraction of oxygen from oxygenated water. The coverage of the surface with the plastron air layer was measured using confocal microscopy. A zinc/oxygen cell is used to consume oxygen within containers constructed from the different membranes, and the oxygen consumed by the cell is compared to the change in oxygen concentration as measured by an oxygen probe. By comparing the membranes to an air-tight reference sample, it was found that the membranes facilitated oxygen transfer from the water into the container, with the most successful membrane showing a 1.90:1 ratio between the cell oxygen consumption and the change in concentration within the container.


    Directory of Open Access Journals (Sweden)

    GROSU Marian C


    Full Text Available A coated material is a composite structure that consists of at least two components: base material and coating layer. The purpose of coating is to provide special properties to base material, with potential to be applied in EMI shielding and diverse smart technical fields. This paper reports the results of a study about some physical and magnetic properties of coated woven fabrics made from cotton yarns with fineness of 17 metric count. For this aim, a plain woven fabric was coated with a solution hard magnetic polymer based. As hard magnetic powder, barium hexaferrite (BaFe12O19 was selected. The plain woven fabric used as base has been coated with five solutions having different amounts of hard magnetic powder (15% - 45% in order to obtain five different magnetic woven fabrics. A comparison of physical properties regarding weight (g/m2, thickness (mm, degree of charging (% and magnetic properties of magnetic woven samples were presented. Saturation magnetizing (emu/g, residual magnetizing (emu/g and coercive force (kA/m of pure hard magnetic powder and woven fabrics have been studied as hysteresis characteristics. The magnetic properties of the woven fabrics depend on the mass percentage of magnetic powder from coating solution. Also, the residual magnetism and coercive field of woven fabrics represents only a part of bulk barium hexafferite residual magnetism and coercive field.

  12. Superamphiphobic cotton fabrics with enhanced stability (United States)

    Xu, Bi; Ding, Yinyan; Qu, Shaobo; Cai, Zaisheng


    Superamphiphobic cotton fabrics were prepared by alternately depositing organically modified silica alcogel (ormosil) particles onto chitosan precoated cotton fabrics and subsequent 1H, 1H, 2H, 2H-perfluorooctyltrimethoxysilane (PFOTMS) modification. Transmission electron microscopy and scanning electron microscopy images reveal that the ormosil particles display a fluffy, sponge-like nanoporous structure, and the entire cotton fiber surface is covered with highly porous networks. PFOTMS acts as not only a modifier to lower the surface energy of the cotton fabric but also a binder to enhance the coating stability against abrasion and washing. The treated cotton fabrics show highly liquid repellency with the water, cooking oil and hexadecane contact angels reaching to 164.4°, 160.1° and 156.3°, respectively. Meanwhile, the treated cotton fabrics exhibit good abrasion resistance and high laundering durability, which can withstand 10,000 cycles of abrasion and 30 cycles of machine wash without apparently changing the superamphiphobicity. The superamphiphobic cotton fabric also shows high acid stability, and can withstand 98% H2SO4. Moreover, the superamphiphobic coating has almost no influence on the other physical properties of the cotton fabrics including tensile strength, whiteness and air permeability. This durable non-wetting surface may provide a wide range of new applications in the future.

  13. Heat Transfer in Directional Water Transport Fabrics

    Directory of Open Access Journals (Sweden)

    Chao Zeng


    Full Text Available Directional water transport fabrics can proactively transfer moisture from the body. They show great potential in making sportswear and summer clothing. While moisture transfer has been previously reported, heat transfer in directional water transport fabrics has been little reported in research literature. In this study, a directional water transport fabric was prepared using an electrospraying technique and its heat transfer properties under dry and wet states were evaluated, and compared with untreated control fabric and the one pre-treated with NaOH. All the fabric samples showed similar heat transfer features in the dry state, and the equilibrium temperature in the dry state was higher than for the wet state. Wetting considerably enhanced the thermal conductivity of the fabrics. Our studies indicate that directional water transport treatment assists in moving water toward one side of the fabric, but has little effect on thermal transfer performance. This study may be useful for development of “smart” textiles for various applications.

  14. Superamphiphobic cotton fabrics with enhanced stability

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Bi, E-mail: [National Engineering Research Center for Dyeing and Finishing of Textiles, Donghua University, Shanghai 201620 (China); Key Laboratory of Science & Technology of Eco-Textile, Ministry of Education, Donghua University, Shanghai 201620 (China); College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Ding, Yinyan; Qu, Shaobo [College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China); Cai, Zaisheng, E-mail: [College of Chemistry, Chemical Engineering and Biotechnology, Donghua University, Shanghai 201620 (China)


    Highlights: • Superamphiphobic cotton fabrics were prepared. • Water and hexadecane contact angels reach to 164.4° and 156.3°, respectively. • Nanoporous organically modified silica alcogel particles were synthesized. • The superamphiphobic cotton fabrics exhibit enhanced stability against abrasion, laundering and acid. - Abstract: Superamphiphobic cotton fabrics were prepared by alternately depositing organically modified silica alcogel (ormosil) particles onto chitosan precoated cotton fabrics and subsequent 1H, 1H, 2H, 2H-perfluorooctyltrimethoxysilane (PFOTMS) modification. Transmission electron microscopy and scanning electron microscopy images reveal that the ormosil particles display a fluffy, sponge-like nanoporous structure, and the entire cotton fiber surface is covered with highly porous networks. PFOTMS acts as not only a modifier to lower the surface energy of the cotton fabric but also a binder to enhance the coating stability against abrasion and washing. The treated cotton fabrics show highly liquid repellency with the water, cooking oil and hexadecane contact angels reaching to 164.4°, 160.1° and 156.3°, respectively. Meanwhile, the treated cotton fabrics exhibit good abrasion resistance and high laundering durability, which can withstand 10,000 cycles of abrasion and 30 cycles of machine wash without apparently changing the superamphiphobicity. The superamphiphobic cotton fabric also shows high acid stability, and can withstand 98% H{sub 2}SO{sub 4}. Moreover, the superamphiphobic coating has almost no influence on the other physical properties of the cotton fabrics including tensile strength, whiteness and air permeability. This durable non-wetting surface may provide a wide range of new applications in the future.


    Energy Technology Data Exchange (ETDEWEB)

    C. R. Clark; J. F. Jue; G. A. Moore; N. P. Hallinan; B. H. Park; D. E. Burkes


    Efforts to develop a viable monolithic research reactor fuel plate have continued at Idaho National Laboratory. These efforts have concentrated on both fabrication process refinement and scale-up to produce full sized fuel plates. Progress at INL has led to fabrication of hot isostatic pressed uranium-molybdenum bearing monolithic fuel plates. These miniplates are part of the RERTR-8 miniplate irradiation test. Further progress has also been made on friction stir weld processing which has been used to fabricate full size fuel plates which will be irradiated in the ATR and OSIRIS reactors.

  16. Design, fabrication and installation of irradiation facilities

    Energy Technology Data Exchange (ETDEWEB)

    Sim, Bong Shick; Kim, Y. S.; Lee, C. Y. and others


    The principal contents of this project are to design, fabricate and install the steady-state fuel test loop in HANARO for nuclear technology development. Procurement and fabrication of main equipment, licensing and technical review for fuel test loop have been performed during 2 years(1997, 1998) for this project. Following contents are described in the report. - Procurement and fabrication of the equipment, piping for OPS - IPS manufacture - License - Technical review and evaluation of the FTL facility. As besides, as these irradiation facilities will be installed in HANARO, review of safety concern, discussion with KINS for licensing and review ofHANARO interface have been performed respectively. (author)

  17. Heat Generation by Polypyrrole Coated Glass Fabric

    Directory of Open Access Journals (Sweden)

    A. M. Rehan Abbasi


    Full Text Available Vapor deposition technique was employed to coat polypyrrole (PPy on glass substrate using FeCl3 as oxidant and p-toluenesulfonic acid (−OTs as doping agent. The Joule heating effect of PPy coated E-glass fabric was studied by supplying various DC electric fields. The coated fabric exhibited reasonable electrical stability, possessed medium electrical conductivity and was effective in heat generation. An increase in temperature of conductive fabric subjected to constant voltage was observed whereas decrease in power consumption was recorded. Thickness of PPy coating on glass fibers was analyzed by Laser confocal microscope and scanning electron microscope.

  18. Active chainmail fabrics for soft robotic applications (United States)

    Ransley, Mark; Smitham, Peter; Miodownik, Mark


    This paper introduces a novel type of smart textile with electronically responsive flexibility. The chainmail inspired fabric is modelled parametrically and simulated via a rigid body physics framework with an embedded model of temperature controlled actuation. Our model assumes that individual fabric linkages are rigid and deform only through their own actuation, thereby decoupling flexibility from stiffness. A physical prototype of the active fabric is constructed and it is shown that flexibility can be significantly controlled through actuator strains of ≤10%. Applications of these materials to soft-robotics such as dynamically reconfigurable orthoses and splints are discussed.

  19. Silicon fabric for multi-functional applications

    KAUST Repository

    Sevilla, Galo T.


    This paper reports a generic process flow to fabricate mechanically flexible and optically semi-transparent thermoelectric generators (TEGs), micro lithium-ion batteries (μLIB) and metal-oxide-semiconductor capacitors (MOSCAPs) on mono-crystalline silicon fabric platforms from standard bulk silicon (100) wafers. All the fabricated devices show outstanding mechanical flexibility and performance, making an important step towards monolithic integration of Energy Chip (self-powered devices) including energy harvesters and electronic devices on flexible platforms. We also report a recyclability process for the remaining bulk substrate after release, allowing us to achieve a low cost flexible platform for high performance applications. © 2013 IEEE.

  20. Ultrasound technologies for biomaterials fabrication and imaging. (United States)

    Dalecki, Diane; Hocking, Denise C


    Ultrasound is emerging as a powerful tool for developing biomaterials for regenerative medicine. Ultrasound technologies are finding wide-ranging, innovative applications for controlling the fabrication of bioengineered scaffolds, as well as for imaging and quantitatively monitoring the properties of engineered constructs both during fabrication processes and post-implantation. This review provides an overview of the biomedical applications of ultrasound for imaging and therapy, a tutorial of the physical mechanisms through which ultrasound can interact with biomaterials, and examples of how ultrasound technologies are being developed and applied for biomaterials fabrication processes, non-invasive imaging, and quantitative characterization of bioengineered scaffolds in vitro and in vivo.

  1. Fabrication of biopolymer cantilevers using nanoimprint lithography

    DEFF Research Database (Denmark)

    Keller, Stephan Sylvest; Feidenhans'l, Nikolaj Agentoft; Fisker-Bødker, Nis


    The biodegradable polymer poly(l-lactide) (PLLA) was introduced for the fabrication of micromechanical devices. For this purpose, thin biopolymer films with thickness around 10 μm were spin-coated on silicon substrates. Patterning of microcantilevers is achieved by nanoimprint lithography. A major...... challenge was the high adhesion between PLLA and silicon stamp. Optimized stamp fabrication and the deposition of a 125 nm thick fluorocarbon anti-stiction coating on the PLLA allowed the fabrication of biopolymer cantilevers. Resonance frequency measurements were used to estimate the Young’s modulus...

  2. Fabric Reconstruction Based on Sustainable Development: Take the Type of Fabric Recycling as an Example

    Directory of Open Access Journals (Sweden)

    Zhangting Guan


    Full Text Available Sustainable development is a very important concept of our time, it wants to do is to live in harmony with people, to protect the environment where our human survival. Fabric recycling refers to the use of a variety of traditional and high-tech means of the existing fabric fabric design and processing. So that the surface of a rich visual texture and tactile texture "through the fabric recycling approach. However, the fabric form and clothing design coordination between the clothing design is essential to the link! Garment fabric is not only the material basis of clothing modeling But also an important form of plastic arts. Fabric recycling art has gradually become a new breakthrough point of fashion design! And become an important means to increase the added value of clothing products. But at the same time fabric recycling also follow the concept of sustainable development. This paper analyzes the relationship between fabric reengineering and sustainable development. Combined with practice to explore the fabric processing technology and its creative ideas and some of its environmental performance.

  3. Fabrication of 3D Silicon Sensors

    Energy Technology Data Exchange (ETDEWEB)

    Kok, A.; Hansen, T.E.; Hansen, T.A.; Lietaer, N.; Summanwar, A.; /SINTEF, Oslo; Kenney, C.; Hasi, J.; /SLAC; Da Via, C.; /Manchester U.; Parker, S.I.; /Hawaii U.


    Silicon sensors with a three-dimensional (3-D) architecture, in which the n and p electrodes penetrate through the entire substrate, have many advantages over planar silicon sensors including radiation hardness, fast time response, active edge and dual readout capabilities. The fabrication of 3D sensors is however rather complex. In recent years, there have been worldwide activities on 3D fabrication. SINTEF in collaboration with Stanford Nanofabrication Facility have successfully fabricated the original (single sided double column type) 3D detectors in two prototype runs and the third run is now on-going. This paper reports the status of this fabrication work and the resulted yield. The work of other groups such as the development of double sided 3D detectors is also briefly reported.

  4. Cyanobacterial exopolymer properties differentiate microbial carbonate fabrics. (United States)

    Shiraishi, Fumito; Hanzawa, Yusaku; Okumura, Tomoyo; Tomioka, Naotaka; Kodama, Yu; Suga, Hiroki; Takahashi, Yoshio; Kano, Akihiro


    Although environmental changes and evolution of life are potentially recorded via microbial carbonates, including laminated stromatolites and clotted thrombolites, factors controlling their fabric are still a matter of controversy. Herein, we report that the exopolymer properties of different cyanobacterial taxa primarily control the microbial carbonates fabrics in modern examples. This study shows that the calcite encrustation of filamentous Phormidium sp. secreting acidic exopolymers forms the laminated fabric of stromatolites, whereas the encrustation of coccoid Coelosphaeriopsis sp. secreting acidic exopolymers and poor calcification of filamentous Leptolyngbya sp. secreting non-acidic exopolymers form peloids and fenestral structures, respectively, i.e. the clotted fabric of thrombolites. Based on these findings, we suggest that the rise and decline of cyanobacteria possessing different exopolymer properties caused the expansion of thrombolites around the Proterozoic/Cambrian boundary.

  5. Free form fabrication of thermoplastic composites

    Energy Technology Data Exchange (ETDEWEB)

    Kaufman, S.G.; Spletzer, B.L.; Guess, T.R.


    This report describes the results of composites fabrication research sponsored by the Laboratory Directed Research and Development (LDRD) program at Sandia National Laboratories. They have developed, prototyped, and demonstrated the feasibility of a novel robotic technique for rapid fabrication of composite structures. Its chief innovation is that, unlike all other available fabrication methods, it does not require a mold. Instead, the structure is built patch by patch, using a rapidly reconfigurable forming surface, and a robot to position the evolving part. Both of these components are programmable, so only the control software needs to be changed to produce a new shape. Hence it should be possible to automatically program the system to produce a shape directly from an electronic model of it. It is therefore likely that the method will enable faster and less expensive fabrication of composites.

  6. Fabrication of carbohydrate microarrays through boronate formation. (United States)

    Hsiao, Hsuan-Yi; Chen, Mu-Lin; Wu, Huan-Ting; Huang, Li-De; Chien, Wei-Ting; Yu, Ching-Ching; Jan, Fan-Dan; Sahabuddin, Sk; Chang, Tsung-Che; Lin, Chun-Cheng


    A straightforward method for fabricating a stable and covalent carbohydrate microarray based on boronate formation between the hydroxyl groups of carbohydrate and boronic acid (BA) on the glass surface was used to identify carbohydrate-protein interactions.

  7. Impediments for Digital Fabrication in Education

    DEFF Research Database (Denmark)

    Smith, Rachel Charlotte; Iversen, Ole Sejer; Veerasawmy, Rune


    of technology and design is largely absent. The paper addresses the experiences and challenges that digital fabrication technology present for teachers in educational environments, and the impediments that are linked to the teachers' roles in design processes of digital fabrication. Based on a research study......Digital fabrication technologies are increasingly integrated across subjects in primary and secondary education. Focus on the potentials of these technologies has mainly been on the support to STEM oriented learning goals, while emphasis on teachers' roles with the new learning processes...... with eight primary and lower secondary teachers, the findings point to four central impediments for integrating digital fabrication and design into school environments. The findings extend current perceptions of digital technology in education towards exploratory processes of investigation in which...

  8. REVIEW ARTICLE: Plasmonic components fabrication via nanoimprint (United States)

    Boltasseva, Alexandra


    A review report on nanoimprinted plasmonic components is given. The fabrication of different metal-dielectric geometries and nanostructured surfaces that support either propagating or localized surface plasmon modes is discussed. The main characteristics and advantages of the nanoimprint technology for the fabrication of various plasmonic structures are outlined. The discussion of plasmonic waveguiding structures focuses on planar waveguides based on metal strips embedded into a dielectric and on profiled metal surfaces. Nanoimprint-based fabrication of two-dimensional nanostructured plasmonic surfaces for enhanced transmission studies and sensor applications is also discussed. Throughout the report, the main fabrication schemes are described, as well as the challenges facing future manufacturing of plasmonic components for device applications.

  9. Fabrication of LD-3 Polymer Directional Couplers

    National Research Council Canada - National Science Library

    Chen, Ray T


    .... LD-3 polymer directional couplers arc designed and fabricated to operate at 1.3 microns. Waveguide propagation losses, device characterization, demonstration of cross coupling and packaged device pictures are presented in this final report.

  10. A scalable fabrication process of polymer microneedles

    National Research Council Canada - National Science Library

    Yang, Sixing; Feng, Yan; Zhang, Lijun; Chen, Nixiang; Yuan, Weien; Jin, Tuo


    While polymer microneedles may easily be fabricated by casting a solution in a mold, either centrifugation or vacuumizing is needed to pull the viscous polymer solution into the microholes of the mold...

  11. Diffractive optics: design, fabrication, and test

    National Research Council Canada - National Science Library

    O'Shea, Donald C


    This book provides the reader with the broad range of materials that were discussed in a series of short courses presented at Georgia Tech on the design, fabrication, and testing of diffractive optical elements (DOEs...

  12. Electrical Ground Support Equipment Fabrication, Specification for (United States)

    Denson, Erik C.


    This document specifies parts, materials, and processes used in the fabrication, maintenance, repair, and procurement of electrical and electronic control and monitoring equipment associated with ground support equipment (GSE) at the Kennedy Space Center (KSC).

  13. Studies on Wicking Behaviour of Polyester Fabric

    Directory of Open Access Journals (Sweden)

    Arobindo Chatterjee


    Full Text Available This paper aims to investigate vertical wicking properties of polyester fabric based on change in sample direction and change in tension. Also experimental results are compared with theoretical results. Polyester fabric made out of spun yarn with four types of variation in pick density was used. Theoretical values of vertical wicking were calculated by using Lucas-Washburn equation and experimental results were recorded using strip test method. Maximum height reached experimentally in both warp way and weft way is more than that of the theoretical values. The maximum height attained by fabric experimentally in weft is more as compared to warp way. Vertical wicking increases with increase in tension. This paper is focused on wicking which plays a vital role in determining comfort and moisture transport behavior of fabric.

  14. Metal bellows custom-fabricated from tubing (United States)


    Mandrel assembly mounted in a lathe chuck is used with a forming wheel to roll-form bellows from standard sheet metal tubing. Spacers and mandrels of various sizes custom-fabricate bellows of any desired dimensions.

  15. Fabricating plasmonic components for nano-and meta-photonics

    DEFF Research Database (Denmark)

    Boltasseva, Alexandra; Nielsen, Rasmus Bundgaard; Jeppesen, Claus


    Different fabrication approaches for realization of metal-dielectric structures supporting propagating and localized surface plasmons are described including fabrication of nanophotonic waveguides and plasmonic nanoantennae....

  16. New knitted fabric concepts for denim products (United States)

    Marmaralı, A.; Ertekin, G.; Oğlakcıoğlu, N.; Kertmen, M.; Seçil Aydın, İ.


    “Denim” like knitted fabric is a new trend combining the appearance of woven denim with the knitted structures’ characteristics such as flexibility, softness, wrinkle resistance, user-friendliness, and comfortable. According to the requirements of markets, it can be obviously seen that, this fabric will be a new era for denim industry which can be competitive with woven denim garments. This study presents general information and literature survey about denim production, knitted denim structures and their characteristics.

  17. Fabrication of Polymer Optical Fibre (POF Gratings

    Directory of Open Access Journals (Sweden)

    Yanhua Luo


    Full Text Available Gratings inscribed in polymer optical fibre (POF have attracted remarkable interest for many potential applications due to their distinctive properties. This paper overviews the current state of fabrication of POF gratings since their first demonstration in 1999. In particular we summarize and discuss POF materials, POF photosensitivity, techniques and issues of fabricating POF gratings, as well as various types of POF gratings.

  18. Superheated droplet detector response to fabrication variations

    Energy Technology Data Exchange (ETDEWEB)

    Felizardo, M., E-mail: felizardo@itn.p [Instituto Tecnologico e Nuclear, Estrada Nacional 10, 2686-953 Sacavem (Portugal); Centro de Fisica Nuclear, Universidade de Lisboa, 1649-003 Lisbon (Portugal); Instituto de Telecomunicacoes, IST, Av. Rovisco Pais 1, 1049-001 Lisbon (Portugal); Morlat, T.; Girard, T.A. [Centro de Fisica Nuclear, Universidade de Lisboa, 1649-003 Lisbon (Portugal); Martins, R.C. [Instituto de Telecomunicacoes, IST, Av. Rovisco Pais 1, 1049-001 Lisbon (Portugal); Ramos, A.R.; Marques, J.G. [Instituto Tecnologico e Nuclear, Estrada Nacional 10, 2686-953 Sacavem (Portugal); Centro de Fisica Nuclear, Universidade de Lisboa, 1649-003 Lisbon (Portugal)


    Constructions of superheated droplet detectors (SDDs) are easily (and sometimes unavoidably) altered in the fabrication process by small variations in the ingredient concentrations and fractionating of the superheated liquid. The devices have moreover been stored at temperatures below 0 deg. C prior to usage in order to de-sensitize their response during transport. We report studies of the response differences of high concentration SDDs with respect to variations common to their fabrication, to include ageing, concentration, gel stiffness, and droplet size.

  19. Multilayer fabric stratification pipes for solar tanks

    DEFF Research Database (Denmark)

    Andersen, Elsa; Furbo, Simon; Fan, Jianhua


    be achieved by use of inlet stratifiers combined with low flow operation in the solar collector loop. In this paper, investigations of a number of different fabric stratification pipes are presented and compared to a non flexible inlet stratifier. Additional, detailed investigations of the flow structure...... close to two fabric stratification pipes are presented for one set of operating conditions by means of the optical PIV (Particle Image Velocimetry) method....

  20. Carbon nanotube collimator fabrication and application (United States)

    Chow, Lee; Chai, Guangyu; Schenkel, Thomas


    Apparatus, methods, systems and devices for fabricating individual CNT collimators. Micron size fiber coated CNT samples are synthesized with chemical vapor deposition method and then the individual CNT collimators are fabricated with focused ion beam technique. Unfocused electron beams are successfully propagated through the CNT collimators. The CNT nano-collimators are used for applications including single ion implantation and in high-energy physics, and allow rapid, reliable testing of the transmission of CNT arrays for transport of molecules.

  1. Coliform bacteria, fabrics, and the environment. (United States)

    Colclasure, Victoria J; Soderquist, Thomas J; Lynch, Thomas; Schubert, Nina; McCormick, Deirdre S; Urrutia, Erika; Knickerbocker, Corey; McCord, Devon; Kavouras, Jerry H


    People come into contact with coliform bacteria at recreational sites. Previous research on bacteria adhering to fabrics and surfaces focused on the viability of clinically significant microbes, but did not examine the quantity of bacteria. This study examined the viability and quantity of coliform bacteria adhered to common fabrics. The fabrics of 100% cotton, blended cotton, and silk were exposed to a mixture of environmental coliform isolates. Fabrics were incubated in the dark at 25°C or 37°C or in direct sunlight at room temperature for 30, 60, 90, and 120 days. The quantity and viability of the bacteria were determined by the Most Probable Number technique using Colilert reagent (IDEXX Laboratories, Westbrook, ME) and eosin methylene blue agar, respectively. The highest numbers of bacteria were detected for each type of fabric when stored in the dark at 25°C, whereas the lowest numbers of bacteria were detected when fabrics were stored in the dark at 37°C. Low numbers of bacteria were detected on silk and blended cotton exposed to sunlight at room temperature, but not 100% cotton. It appears that coliform bacteria can survive on fabrics longer than previous studies have reported. Coliform bacteria survive better in the dark, at lower temperatures, and on fabrics that can retain moisture. These findings can be applied directly to the viability of bacteria on clothing and potential human exposure to fecal pathogens. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

  2. Method to fabricate layered material compositions (United States)

    Fleming, James G.; Lin, Shawn-Yu


    A new class of processes suited to the fabrication of layered material compositions is disclosed. Layered material compositions are typically three-dimensional structures which can be decomposed into a stack of structured layers. The best known examples are the photonic lattices. The present invention combines the characteristic features of photolithography and chemical-mechanical polishing to permit the direct and facile fabrication of, e.g., photonic lattices having photonic bandgaps in the spectral range.

  3. Kinetic Friction of Sport Fabrics on Snow

    Directory of Open Access Journals (Sweden)

    Werner Nachbauer


    Full Text Available After falls, skiers or snowboarders often slide on the slope and may collide with obstacles. Thus, the skier’s friction on snow is an important factor to reduce incidence and severity of impact injuries. The purpose of this study was to measure snow friction of different fabrics of ski garments with respect to roughness, speed, and contact pressure. Three types of fabrics were investigated: a commercially available ski overall, a smooth downhill racing suit, and a dimpled downhill racing suit. Friction was measured for fabrics taped on a short ski using a linear tribometer. The fabrics’ roughness was determined by focus variation microscopy. Friction coefficients were between 0.19 and 0.48. Roughness, friction coefficient, and friction force were highest for the dimpled race suit. The friction force of the fabrics was higher for the higher contact pressure than for the lower one at all speeds. It was concluded that the main friction mechanism for the fabrics was dry friction. Only the fabric with the roughest surface showed friction coefficients, which were high enough to sufficiently decelerate a sliding skier on beginner and intermediate slopes.

  4. EIT-Based Fabric Pressure Sensing

    Directory of Open Access Journals (Sweden)

    A. Yao


    Full Text Available This paper presents EIT-based fabric sensors that aim to provide a pressure mapping using the current carrying and voltage sensing electrodes attached to the boundary of the fabric patch. Pressure-induced shape change over the sensor area makes a change in the conductivity distribution which can be conveyed to the change of boundary current-voltage data. This boundary data is obtained through electrode measurements in EIT system. The corresponding inverse problem is to reconstruct the pressure and deformation map from the relationship between the applied current and the measured voltage on the fabric boundary. Taking advantage of EIT in providing dynamical images of conductivity changes due to pressure induced shape change, the pressure map can be estimated. In this paper, the EIT-based fabric sensor was presented for circular and rectangular sensor geometry. A stretch sensitive fabric was used in circular sensor with 16 electrodes and a pressure sensitive fabric was used in a rectangular sensor with 32 electrodes. A preliminary human test was carried out with the rectangular sensor for foot pressure mapping showing promising results.


    Directory of Open Access Journals (Sweden)

    A.K.M. Mobarok Hossain


    Full Text Available Global demand for knitted garments is growing at a faster rate than that of woven items.Currently around 50% of clothing needs in the developed countries is met by knit goods. So ensuring the required quality in a knitted fabric is a vital issue for the manufacturer. One of the major problems encountered in knitted fabric is spirality. It affects particularly single jersey fabric and presents a serious problem during garment confection and use. So controlling spirality is a basic requirement for producing quality knitted fabric. Though there are several factors that contribute to knitted fabric spirality, yarn twist and relative tightness of the fabric are said tobe the most significant ones. In this work the basic single jersey fabric, i.e. plain jersey cotton fabrics were produced by a Hosiery knitting machine and spirality values were observed for different yarn T.P.I. and tightness factor at relaxed state. It was found that tightness factor has a direct influence on knitted fabric spirality with a high degree of correlation. The work thus gives an idea to deal this problem by controlling the knitting parameters.

  6. Qualitative Investigation of Some Locally Produced Printed Fabrics ...

    African Journals Online (AJOL)

    Qualitative analysis of some selected locally produced fabrics and foreign fabrics marketed in Nigeria was carried out. The comparative study of the Physico – mechanical properties of the fabrics were made. The results obtained showed that the locally produced fabrics exhibited comparably better end – use performance ...

  7. 25 CFR 307.4 - Standards for fabrics. (United States)


    ... 25 Indians 2 2010-04-01 2010-04-01 false Standards for fabrics. 307.4 Section 307.4 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO ALL-WOOL WOVEN FABRICS; USE OF GOVERNMENT CERTIFICATE OF GENUINENESS § 307.4 Standards for fabrics. No fabric may carry the Government certificate of...

  8. 3D Bioprinting for Vascularized Tissue Fabrication. (United States)

    Richards, Dylan; Jia, Jia; Yost, Michael; Markwald, Roger; Mei, Ying


    3D bioprinting holds remarkable promise for rapid fabrication of 3D tissue engineering constructs. Given its scalability, reproducibility, and precise multi-dimensional control that traditional fabrication methods do not provide, 3D bioprinting provides a powerful means to address one of the major challenges in tissue engineering: vascularization. Moderate success of current tissue engineering strategies have been attributed to the current inability to fabricate thick tissue engineering constructs that contain endogenous, engineered vasculature or nutrient channels that can integrate with the host tissue. Successful fabrication of a vascularized tissue construct requires synergy between high throughput, high-resolution bioprinting of larger perfusable channels and instructive bioink that promotes angiogenic sprouting and neovascularization. This review aims to cover the recent progress in the field of 3D bioprinting of vascularized tissues. It will cover the methods of bioprinting vascularized constructs, bioink for vascularization, and perspectives on recent innovations in 3D printing and biomaterials for the next generation of 3D bioprinting for vascularized tissue fabrication.

  9. Overview of the GTRI Fuel Fabrication Capability

    Energy Technology Data Exchange (ETDEWEB)

    Burkes, Douglas; Longmire, Holly A.; Dombrowski, Dave; Cole, Lance


    The Global Threat Reduction Initiative’s (GTRI) Fuel Fabrication Capability (FFC) has been tasked with the establishment and deployment of a fabrication process for the low-enriched uranium-molybdenum (LEU-Mo) monolithic fuel that is currently under development for supply to the U.S. research and test reactor community. The FFC has been designed to bridge fuel fabrication scope and interest between industry (both national and international), the U.S. Nuclear Regulatory Commission, multiple U.S. national laboratories, and reactor operators and stakeholders. Currently, the FFC is focusing much of its efforts on technology maturation and scale-up of reference processes that have been defined by the GTRI Fuel Development project. This emphasis revolves around three key criteria: (i) establishing the ability to meet throughput demands, (ii) keeping costs as low as reasonably possible, and (iii) ensuring a quality product. At present, the effect of changing fuel fabrication variables on U-Mo monolithic fuel performance is not fully understood. Furthermore, it is likely that the foil production process will continue to evolve with scale-up and commercial deployment. This paper will address the areas that the FFC is focusing on to better understand the impacts of fuel fabrication variables on the resultant fuel plate characteristics, based upon a traditional approach to fuel design qualification and licensing.

  10. Composite fabrication via resin transfer molding technology

    Energy Technology Data Exchange (ETDEWEB)

    Jamison, G.M.; Domeier, L.A.


    The IMPReS (Integrated Modeling and Processing of Resin-based Structures) Program was funded in FY95 to consolidate, evaluate and enhance Sandia`s capabilities in the design and fabrication of composite structures. A key driver of this and related programs was the need for more agile product development processes and for model based design and fabrication tools across all of Sandia`s material technologies. A team of polymer, composite and modeling personnel was assembled to benchmark Sandia`s existing expertise in this area relative to industrial and academic programs and to initiate the tasks required to meet Sandia`s future needs. RTM (Resin Transfer Molding) was selected as the focus composite fabrication technology due to its versatility and growing use in industry. Modeling efforts focused on the prediction of composite mechanical properties and failure/damage mechanisms and also on the uncured resin flow processes typical of RTM. Appropriate molds and test composites were fabricated and model validation studies begun. This report summarizes and archives the modeling and fabrication studies carried out under IMPReS and evaluates the status of composite technology within Sandia. It should provide a complete and convenient baseline for future composite technology efforts within Sandia.

  11. Fabrication of polydopamine-coated superhydrophobic fabrics for oil/water separation and self-cleaning (United States)

    Xu, Zhanglian; Miyazaki, Koji; Hori, Teruo


    We report a fabric coating method inspired the superhydrophobic properties of lotus leaves and the strong adhesion of the adhesive proteins in mussels. Dopamine, which mimics the single units of the adhesive mussel proteins, was polymerized in an alkaline aqueous solution to coat the surface of fabrics. The versatile reactivity of polydopamine allows subsequent Ag deposition to form a lotus-leaf-like rough structure on the fabric surface. The composite fabric exhibited high water repellence after fluorination. Because dopamine can adhere to all kinds of materials, this method can be applied to many fabrics regardless of their properties and chemical compositions using a universal process. The modified fabrics exhibited excellent anti-wetting and self-cleaning properties with contact angles of >150° and sliding angles lower than 9°. The fabrics also efficiently separated oil from oil/water mixtures under various conditions. Our method is versatile and simple compared with other hydrophobic treatment methods, which usually only work on one type of fabric.

  12. Development of technology for fabrication of lithium CPS on basis of CNT-reinforced carboxylic fabric

    Energy Technology Data Exchange (ETDEWEB)

    Tazhibayeva, Irina, E-mail: [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Baklanov, Viktor; Ponkratov, Yuriy [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Abdullin, Khabibulla [Institute of Experimental and Theoretical Physics of Kazakh National University, Almaty (Kazakhstan); Kulsartov, Timur; Gordienko, Yuriy; Zaurbekova, Zhanna [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan); Lyublinski, Igor [JSC «Red Star», Moscow (Russian Federation); NRNU «MEPhI», Moscow (Russian Federation); Vertkov, Alexey [JSC «Red Star», Moscow (Russian Federation); Skakov, Mazhyn [Institute of Atomic Energy, National Nuclear Center of RK, Kurchatov (Kazakhstan)


    Highlights: • Preliminary study of carboxylic fabric wettability with liquid lithium is presented. • Preliminary studies of carboxylic fabric wettability with liquid lithium consist in carrying out of experiments at temperatures 673,773 and 873 К in vacuum during long time. • A scheme of experimental device for manufacturing of lithium CPS and matrix filling procedure with liquid lithium are presented. • The concept of lithium limiter with CPS on basis of CNT-reinforced carboxylic fabric is proposed. - Abstract: The paper describes the analysis of liquid lithium interaction with materials based on carbon, the manufacture technology of capillary-porous system (CPS) matrix on basis of CNT-reinforced carboxylic fabric. Preliminary study of carboxylic fabric wettability with liquid lithium is presented. The development of technology includes: microstructural studies of carboxylic fabric before its CNT-reinforcing; validation of CNT-reinforcing technology; mode validation of CVD-method for CNT synthesize; study of synthesized carbon structures. Preliminary studies of carboxylic fabric wettability with liquid lithium consist in carrying out of experiments at temperatures 673, 773 and 873 К in vacuum during long time. The scheme of experimental device for manufacturing of lithium CPS and matrix filling procedure with liquid lithium are presented. The concept of lithium limiter with CPS on basis of CNT-reinforced carboxylic fabric is proposed.

  13. Digital fabrication of textiles: an analysis of electrical networks in 3D knitted functional fabrics (United States)

    Vallett, Richard; Knittel, Chelsea; Christe, Daniel; Castaneda, Nestor; Kara, Christina D.; Mazur, Krzysztof; Liu, Dani; Kontsos, Antonios; Kim, Youngmoo; Dion, Genevieve


    Digital fabrication methods are reshaping design and manufacturing processes through the adoption of pre-production visualization and analysis tools, which help minimize waste of materials and time. Despite the increasingly widespread use of digital fabrication techniques, comparatively few of these advances have benefited the design and fabrication of textiles. The development of functional fabrics such as knitted touch sensors, antennas, capacitors, and other electronic textiles could benefit from the same advances in electrical network modeling that revolutionized the design of integrated circuits. In this paper, the efficacy of using current state-of-the-art digital fabrication tools over the more common trialand- error methods currently used in textile design is demonstrated. Gaps are then identified in the current state-of-the-art tools that must be resolved to further develop and streamline the rapidly growing field of smart textiles and devices, bringing textile production into the realm of 21st century manufacturing.

  14. Fast-Response Electrostatic Actuator Based on Nano-Gap

    Directory of Open Access Journals (Sweden)

    Edward Kostsov


    Full Text Available The possibility of constructing new high-performance electrostatic fast actuators based on energy transformation in nanometer gaps is considered. The construction and the properties of the operation of such devices as well as their typical parameters are described. The drives are based on ferroelectrics with high values of dielectric permittivity (above 1000. They can be constructed using microelectronic technology. It is demonstrated that the actuators are capable of maintaining forces with a specific density up to 106 N/m2 and up to 100–1000 N in real devices for 10–100 µs. Experimental research results of such actuators are presented.

  15. Investigation on mechanical properties of basalt composite fabrics (experiment study)


    Talebi Mazraehshahi H.; Zamani H.


    To fully appreciate the role and application of composite materials to structures, correct understanding of mechanical behaviors required for selection of optimum material. Fabric reinforced composites are composed of a matrix that is reinforced with pliable fabric, glass fabric is most popular reinforcement for different application specially in aircraft structure, although other fabric material are also used. At this study new fabric material called basalt with epoxy resin introduced ...

  16. Effects of fabric thickness and material on apparent 'wet' conductive thermal resistance of knitted fabric 'skin' on sweating manikins. (United States)

    Wang, Faming; Lai, Dandan; Shi, Wen; Fu, Ming


    Currently, no published standard and research work have addressed the basic requirements on knitted fabric 'skin' on sweating manikins. In this study, we performed 252 experiments to investigate the influence of fabric thickness and material on the apparent 'wet' conductive (or effective) thermal resistance of the fabric 'skin' using a 'Newton' manikin. Four types of cotton fabric 'skin' (fabric thickness: 0.38, 0.54, 0.92 and 1.43mm) and three types of polyester fabric 'skin' (fabric thickness: 0.41, 0.54 and 1.0mm) were selected and their 'wet' conductive thermal resistance was determined. Empirical equations were also developed for each fabric 'skin' to predict wet fabric 'skin' surface temperatures. It was found that both fabric thickness and material significantly affected the apparent 'wet' conductive thermal resistance. Clothing total evaporative resistance determined using thin fabric 'skin' (e.g., CO1, CO2) was normally lower than that determined using thick fabric 'skin' (e.g., CO4). Besides, synthetic fabric 'skin' tended to have a larger apparent 'wet' conductive thermal resistance than the cotton fabric 'skin' due to a smaller amount of moisture contained. Hence, there is a great need to standardize the fabric 'skin' to eliminate the influence of fabric 'skin' on the measurement of clothing evaporative resistance by means of a sweating manikin. Copyright © 2017 Elsevier Ltd. All rights reserved.

  17. Fabricating solid carbon porous electrodes from powders (United States)

    Kaschmitter, J.L.; Tran, T.D.; Feikert, J.H.; Mayer, S.T.


    Fabrication is described for conductive solid porous carbon electrodes for use in batteries, double layer capacitors, fuel cells, capacitive deionization, and waste treatment. Electrodes fabricated from low surface area (graphite and cokes exhibit excellent reversible lithium intercalation characteristics, making them ideal for use as anodes in high voltage lithium insertion (lithium-ion) batteries. Electrodes having a higher surface area, fabricated from powdered carbon blacks, such as carbon aerogel powder, carbon aerogel microspheres, activated carbons, etc. yield high conductivity carbon composites with excellent double layer capacity, and can be used in double layer capacitors, or for capacitive deionization and/or waste treatment of liquid streams. By adding metallic catalysts to high surface area carbons, fuel cell electrodes can be produced. 1 fig.

  18. FDC, rapid fabrication of structural components

    Energy Technology Data Exchange (ETDEWEB)

    Agarwala, M.K.; Bandyopadhyay, A.; Weeren, R. van; Safari, A.; Danforth, S.C.; Langrana, N.A. [Rutgers-the State Univ., Piscataway, NJ (United States); Jamalabad, V.R.; Whalen, P.J. [AlliedSignal Research and Technology, Morristown, NJ (United States)


    Solid freeform fabrication (SFF) is used to make 3-D components directly from computer-aided design (CAD) files. Many SFF techniques have been developed to fabricate parts and prototypes from CAD without hard tooling, dies or molds. Most of these techniques have been commercialized for fabrication of polymer and plastic parts for design verification and form and fit. Other SFF techniques are being developed for production of ceramic components with functional properties. One such technique, called fused deposition of ceramics (FDC), has been developed and demonstrated for structural ceramics. FDC is based on existing fused deposition modeling (FDM{trademark}) technology, commercialized by Stratasys Inc. (Eden Prairie, Minn.), for processing of polymers and waxes. High-green-density, simple- and complex-shaped silicon nitride parts have been formed by fused deposition of ceramics.

  19. High Speed Fabrication of Aspheric Surfaces (United States)

    Atkinson, Leland Guy, III

    Automation of the fabrication of optical surfaces have been studied both theoretically and experimentally. An Elastic Polishing Model has been derived which predicts the motions required by an elastic ring tool polisher to polish an optical surface to the desired shape and accuracy. A machine control program has been developed which is used to automatically grind and polish optical surfaces. An Optical Surfacing CAM machine has been designed and constructed using a modified CNC milling machine. The O.S. CAM consists of three fabrication stations used for rough grinding, fine grinding, and polishing. Glass parts are loaded into the tool spindle from an automatic tool changer and then cycled through a fabrication process under computer control. Analysis of the generated and polished optical surfaces is performed using conventional radius gauges, test glasses and a Fizeau interferometer.

  20. Design, fabrication and installation of irradiation facilities

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Yong Sung; Lee, C. Y.; Kim, J. Y.; Chi, D. Y.; Kim, S. H.; Ahn, S. H.; Kim, S. J.; Kim, J. K.; Yang, S. H.; Yang, S. Y.; Kim, H. R.; Kim, H.; Lee, K. H.; Lee, B. C.; Park, C.; Lee, C. T.; Cho, S. W.; Kwak, K. K.; Suk, H. C. [and others


    The principle contents of this project are to design, fabricate and install the steady-state fuel test loop and non-instrumented capsule in HANARO for nuclear technology development. This project will be completed in 1999, the basic and detail design, safety analysis, and procurement of main equipment for fuel test loop have been performed and also the piping in gallery and the support for IPS piping in reactor pool have been installed in 1994. In the area of non-instrumented capsule for material irradiation test, the fabrication of capsule has been completed. Procurement, fabrication and installation of the fuel test loop will be implemented continuously till 1999. As besides, as these irradiation facilities will be installed in HANARO, review of safety concern, discussion with KINS for licensing and safety analysis report has been submitted to KINS to get a license and review of HANARO interface have been performed respectively. (author). 39 refs., 28 tabs., 21 figs.

  1. The LHC Main Quadrupoles during Series Fabrication

    CERN Document Server

    Tortschanoff, Theodor; Durante, M; Hagen, P; Klein, U; Krischel, D; Payn, A; Rossi, L; Schellong, B; Schmidt, P; Simon, F; Schirm, K-M; Todesco, E


    By the end of August 2005 about 320 of the 400 main LHC quadrupole magnets have been fabricated and about 220 of them assembled into their cold masses, together with corrector magnets. About 130 of them have been cold tested in their cryostats and most of the quadrupoles exceeded their nominal excitation, i.e. 12,000 A, after no more than two training quenches. During this series fabrication, the quality of the magnets and cold masses was thoroughly monitored by means of warm magnetic field measurements, of strict geometrical checking, and of various electrical verifications. A number of modifications were introduced in order to improve the magnet fabrication, mainly correction of the coil geometry for achieving the specified field quality and measures for avoiding coil insulation problems. Further changes concern the electrical connectivity and insulation of instrumentation, and of the corrector magnets inside the cold masses. The contact resistances for the bus-bar connections to the quench protection diode...

  2. From sensitive fabrics to distributed wearable sensors (United States)

    De Rossi, Danilo; Mazzoldi, Alberto; Lorussi, Federico; Paradiso, Rita


    Our previous work has shown that elastic textiles covered with an epitaxial layer of conducting polymer show piezoresistive properties. They can be used to fabricate sensorized garments such as gloves, leotards, socks and seat covers as man-machine interfaces. A purposely designed screen printing process has been implemented to realize sensors/tracks patterns. Polypyrrole/lycra fabrics were prepared using the method developed by Milliken Co. (Spartanburg, USA). The epitaxial deposition is obtained controlling the concentrations of monomer and the temperature of the reaction medium. Investigation on mechanoelectric transduction properties (static and dynamic) of the fabrics, calibration of wearable sensing devices and ongoing R&D efforts in multimedia, sport and rehabilitation fields are reported.

  3. Air permeability of polyester nonwoven fabrics

    Directory of Open Access Journals (Sweden)

    Zhu Guocheng


    Full Text Available Air permeability is one of the most important properties of non-woven fabrics in many applications. This paper aims to investigate the effects of thickness, porosity and density on the air permeability of needle-punched non-woven fabrics and compare the experimental values with two models which are based on hydraulic radius theory and drag theory, respectively. The air permeability of the samples was measured by an air permeability tester FX3300. The results showed that the air permeability of non-woven fabrics decreased with the increase in thickness and density of samples, increased with the increase of porosity, and the air permeability was not directly proportional to the pressure gradient. Meanwhile, the prediction model based on hydraulic radius theory had a better agreement with experimental values than the model based on drag theory, but the values were much higher than the experimental results, especially for higher porosity and higher pressure gradient.

  4. CMOS MEMS Fabrication Technologies and Devices

    Directory of Open Access Journals (Sweden)

    Hongwei Qu


    Full Text Available This paper reviews CMOS (complementary metal-oxide-semiconductor MEMS (micro-electro-mechanical systems fabrication technologies and enabled micro devices of various sensors and actuators. The technologies are classified based on the sequence of the fabrication of CMOS circuitry and MEMS elements, while SOI (silicon-on-insulator CMOS MEMS are introduced separately. Introduction of associated devices follows the description of the respective CMOS MEMS technologies. Due to the vast array of CMOS MEMS devices, this review focuses only on the most typical MEMS sensors and actuators including pressure sensors, inertial sensors, frequency reference devices and actuators utilizing different physics effects and the fabrication processes introduced. Moreover, the incorporation of MEMS and CMOS is limited to monolithic integration, meaning wafer-bonding-based stacking and other integration approaches, despite their advantages, are excluded from the discussion. Both competitive industrial products and state-of-the-art research results on CMOS MEMS are covered.

  5. Fabrication of SWCNT based flexible chemiresistor

    Energy Technology Data Exchange (ETDEWEB)

    Rajput, Mayank, E-mail:; Das, S. [Sensors and Nanotechnology Group, CSIR-Central Electronics Engineering Research Institute, Pilani - 333031, Rajasthan (India); Kaur, Rajvinder [Punjabi University, Patiala-147002, Punjab (India); Kumar, Anil, E-mail: [Sensors and Nanotechnology Group, CSIR-Central Electronics Engineering Research Institute, Pilani - 333031, Rajasthan (India); Academy of Scientific and Innovative Research (AcSIR), New Delhi - 110001, India Tel.: +91-1596-246021, fax: +911596242294 (India)


    Carboxyl (-COOH) functionalized SWCNT chemiresistors have been realized on Kapton substrate patterned with Au microelectrodes by the drop casting of functionalized SWCNT dispersion in DI water. I-V measurements on fabricated chemiresistor showed ohmic behavior at different temperatures (25°C-120°C). The effect of bending on flexible functionalized SWCNT chemiresistor for different diameter has been measured. It has been found that bending at different radius of curvature doesn’t change the ohmic behavior of fabricated chemiresistor. Achieved results are promising for cheap flexible electronic devices.

  6. High yield fabrication of fluorescent nanodiamonds (United States)

    Boudou, Jean-Paul; Curmi, Patrick; Jelezko, Fedor; Wrachtrup, Joerg; Aubert, Pascal; Sennour, Mohamed; Balasubramanian, Gopalakrischnan; Reuter, Rolf; Thorel, Alain; Gaffet, Eric


    A new fabrication method to produce homogeneously fluorescent nanodiamonds with high yields is described. The powder obtained by high energy ball milling of fluorescent high pressure, high temperature diamond microcrystals was converted in a pure concentrated aqueous colloidal dispersion of highly crystalline ultrasmall nanoparticles with a mean size less than or equal to 10 nm. The whole fabrication yield of colloidal quasi-spherical nanodiamonds was several orders of magnitude higher than those previously reported starting from microdiamonds. The results open up avenues for the industrial cost-effective production of fluorescent nanodiamonds with well-controlled properties. PMID:19451687

  7. Polymeric Microneedle Array Fabrication by Photolithography. (United States)

    Kathuria, Himanshu; Kochhar, Jaspreet Singh; Fong, Michelle Hui Min; Hashimoto, Michinao; Iliescu, Ciprian; Yu, Hanry; Kang, Lifeng


    This manuscript describes the fabrication of polymeric microneedle (MN) arrays by photolithography. It involves a simple mold-free process by using a photomask consisting of embedded micro-lenses. Embedded micro-lenses were found to influence MN geometry (sharpness). Robust MN arrays with tip diameters ranging between 41.5 µm ± 8.4 µm and 71.6 µm ± 13.7 µm, with two different lengths (1,336 µm ± 193 µm and 957 µm ± 171 µm) were fabricated. These MN arrays may provide potential applications in delivery of low molecular and macromolecular therapeutic agents through skin.

  8. Experimental investigation of braided fabric forming (United States)

    Wang, Peng; Soulat, Damien; Legrand, Xavier; Zemni, Lilia; Jacquot, Pierre-Baptiste


    Woven and braided textile structures are largely used as the composite reinforcements. Forming of the continuous fibre reinforcements and thermoplastic resin commingled yarns can be performed at room temperature. The "cool" forming stage is well-controlled and more economical compared to thermoforming. Many studies have been addressed for carbon and glass fibres / thermoplastic commingled yarns reinforced composite forming for woven structure. On the contrary, few research works has deal with the natural fibre reinforced textile forming and none concerns the braided fabrics forming. In this present work, the Flax/Polyamide 12 commingled yarns are used to produce braided fabric and then to analyze their deformability behaviour.

  9. Nuclear fuel elements design, fabrication and performance

    CERN Document Server

    Frost, Brian R T


    Nuclear Fuel Elements: Design, Fabrication and Performance is concerned with the design, fabrication, and performance of nuclear fuel elements, with emphasis on fast reactor fuel elements. Topics range from fuel types and the irradiation behavior of fuels to cladding and duct materials, fuel element design and modeling, fuel element performance testing and qualification, and the performance of water reactor fuels. Fast reactor fuel elements, research and test reactor fuel elements, and unconventional fuel elements are also covered. This volume consists of 12 chapters and begins with an overvie

  10. Fabrication of nylon/fullerene polymer memory (United States)

    Jayan, Manuvel; Davis, Rosemary; Karthik, M. P.; Devika, K.; Kumar, G. Vijay; Sriraj, B.; Predeep, P.


    Two terminal Organic memories in passive matrix array form with device structure, Al/Nylon/ (Nylon+C60)/Nylon/ Al are fabricated. The current-voltage measurements showed hysteresis and the devices are thoroughly characterized for write-read-erase-read cycles. The control over the dispersion concentration, capacity of fullerene to readily accept electrons and the constant diameter of fullerene made possible uniform device fabrication with reproducible results. Scanning electron micrographs indicated that the device thickness remained uniform in the range of 19 micrometers.

  11. Tensile Fabrics Enhance Architecture Around the World (United States)


    Using a remarkable fabric originally developed to protect Apollo astronauts, Birdair Inc. of Amherst, New York, has crafted highly durable, safe, environmentally friendly, and architecturally stunning tensile membrane roofs for over 900 landmark structures around the world. Travelers in airports, sports fans at stadiums, and shoppers in malls have all experienced the benefits of the Teflon-coated fiberglass fabric that has enabled Birdair to grow from a small company established in its founder?s kitchen in 1955 to a multimillion-dollar specialty contractor today.

  12. Architectural Geometry and Fabrication-Aware Design

    KAUST Repository

    Pottmann, Helmut


    Freeform shapes and structures with a high geometric complexity play an increasingly important role in contemporary architecture. While digital models are easily created, the actual fabrication and construction remains a challenge. This is the source of numerous research problems many of which fall into the area of Geometric Computing and form part of a recently emerging research area, called "Architectural Geometry". The present paper provides a short survey of research in Architectural Geometry and shows how this field moves towards a new direction in Geometric Modeling which aims at combining shape design with important aspects of function and fabrication. © 2013 Kim Williams Books, Turin.

  13. A facile fabrication of multifunctional knit polyester fabric based on chitosan and polyaniline polymer nanocomposite (United States)

    Tang, Xiaoning; Tian, Mingwei; Qu, Lijun; Zhu, Shifeng; Guo, Xiaoqing; Han, Guangting; Sun, Kaikai; Hu, Xili; Wang, Yujiao; Xu, Xiaoqi


    Knit polyester fabric was successively modified and decorated with chitosan layer and polyaniline polymer nanocomposite layer in this paper. The fabric was firstly treated with chitosan to form a stable layer through the pad-dry-cure process, and then the polyaniline polymer nanocomposite layer was established on the outer layer by in situ chemical polymerization method using ammonium persulfate as oxidant and chlorhydric acid as dopant. The surface morphology of coated fabric was characterized by scanning electron microscopy (SEM), and the co-existence of chitosan layer and granular polyaniline polymer nanocomposite was confirmed and well dispersed on the fabric surface. The resultant fabric was endowed with remarkable electrical conductivity properties and efficient water-repellent capability, which also have been found stable after water laundering. In addition, the photocatalytic decomposition activity for reactive red dye was observed when the multifunctional knit polyester fabric was exposed to the illumination of ultraviolet lamp. These results indicated that chitosan and polyaniline polymer nanocomposite could form ideal multifunctional coatings on the surface of knit polyester fabric.

  14. Woven fabric composites: Can we peel it?

    NARCIS (Netherlands)

    Sacchetti, Francisco; Grouve, Wouter Johannes Bernardus; Warnet, Laurent; Villegas, I. Fernandez


    The present work focuses on the applicability of the mandrel peel test to quantify the fracture toughness of woven fabric Carbon/PEEK composites. For this purpose, the mandrel peel test was compared to the standardized DCB test. Unstable crack propagation (stick-slip) was observed in both testing

  15. Micro and nano fabrication tools and processes

    CERN Document Server

    Gatzen, Hans H; Leuthold, Jürg


    For Microelectromechanical Systems (MEMS) and Nanoelectromechanical Systems (NEMS) production, each product requires a unique process technology. This book provides a comprehensive insight into the tools necessary for fabricating MEMS/NEMS and the process technologies applied. Besides, it describes enabling technologies which are necessary for a successful production, i.e., wafer planarization and bonding, as well as contamination control.

  16. Elastocapillary fabrication of three-dimensional microstructures

    NARCIS (Netherlands)

    van Honschoten, J.W.; Berenschot, Johan W.; Ondarcuhu, T.; Sanders, Remco G.P.; Sundaram, J.; Elwenspoek, Michael Curt; Tas, Niels Roelof


    We describe the fabrication of three-dimensional microstructures by means of capillary forces. Using an origami-like technique, planar silicon nitride structures of various geometries are folded to produce three-dimensional objects of 50–100 m. Capillarity is a particularly effective mechanism since

  17. Electrically tunable optofluidic lenses: fabrication and characterization

    NARCIS (Netherlands)

    Mishra, K.


    The objective of this research is to fabricate and characterize an adaptive optofluidic lens device with aberration control. In this work, an electric field is employed as a driving tool to manipulate the liquid-liquid interface for suppressing spherical aberration by using a single flat

  18. Porous Microfluidic Devices - Fabrication adn Applications

    NARCIS (Netherlands)

    de Jong, J.; Geerken, M.J.; Lammertink, Rob G.H.; Wessling, Matthias


    The major part of microfluidic devices nowadays consists of a dense material that defines the fluidic structure. A generic fabrication method enabling the production of completely porous micro devices with user-defined channel networks is developed. The channel walls can be used as a (selective)

  19. Fabrication of hybrid ceramic matrix composites (United States)

    Haug, S. B.; Dharani, L. R.; Carroll, D. R.


    The desire to improve the transverse properties and microcracking stress of unidirectional continuous fiber reinforced ceramic matrix composites has led to development of the hybrid ceramic matrix composite (HCMC). This paper discusses the techniques we used in the fabrication of HCMC specimens used for mechanical characterization.

  20. Properties of natural fabric Polyalthia cerasoides

    CSIR Research Space (South Africa)

    Jayaramudu, J


    Full Text Available The ligno-cellulose natural fabric from the Polyalthia cerasoides tree was analyzed by FTIR, chemical, X-ray and thermo gravimetric methods. The morphology of the fibers was studied by scanning electron and polarized optical microscopic methods...

  1. Microlens array fabrication through crosslinking photopolymerization (United States)

    Croutxe-Barghorn, Celine; Soppera, Olivier; Lougnot, Daniel-Joseph


    Growing interest in miniaturized optical components for various applications such as optical interconnection systems and telecommunication industry have led to the development of several techniques that are used in the fabrication of micro-optical elements. One approach involves the use of polymers as recording materials: these are flexible, highly transparent and cheap. The technique described in the present paper is founded on the ability of self-processing photopolymers to generate refractive microlens arrays. Spatially controlled illumination of a photosensitive layer induces an inhomogeneous photopolymerization involving a mass-transport process of reactive species and generating a relief in the photopolymer layer. The presentation focuses on the fabrication of microlens arrays through photopolymerization with the green line of an argon-ion laser. Surface tension and differential volume shrinkage turned the illuminated area into good quality lenses. The fabricated lens arrays exhibit diameters ranging from less than 20 micrometers to more than 500 micrometers and focal lengths from 100 micrometers to a few millimeters, depending on photonic, optical and physico-chemical parameters. This imaging technique is highly flexible as regards height, shape and optical properties of the lenses that are produced. By starting from the same background, one can also fabricate diffractive optical elements such as gratings and duplicate computer-generated holograms that come increasingly into prominence as the micro-opto-electro-mechanical field expands.

  2. Computation, architectural design and fabrication logic

    DEFF Research Database (Denmark)

    Larsen, Niels Martin


    Digital fabrication and digital form generation can change the way different professions interact in relation to the development and construction of architecture. The technologies can provide a more integrated design process and expand the architectural vocabulary. At Aarhus School of Architecture...

  3. Computational modelling of buckling of woven fabrics

    CSIR Research Space (South Africa)

    Anandjiwala, RD


    Full Text Available The fabric buckling model proposed by Grosberg and Swani has been modified by incorporating Huang’s bilinear bending rule. The proposed model is an extension of the present model and also covers the special cases. The numerical results appear...

  4. Fabrication and characterization of a piezoelectric accelerometer

    DEFF Research Database (Denmark)

    Reus, Roger De; Gulløv, Jens; Scheeper, Patrick


    Zinc oxide based piezoelectric accelerometers were fabricated by bulk micromachining. A high yield was obtained in a relatively simple process sequence. For two electrode configurations a direction selectivity better than 100 was obtained for acceleration in the vertical direction and a selectivity...

  5. Design and fabrication of topologically optimized structures;

    DEFF Research Database (Denmark)

    Feringa, Jelle; Søndergaard, Asbjørn


    Integral structural optimization and fabrication seeks the synthesis of two original approaches; that of topological optimization (TO) and robotic hotwire cutting (HWC) (Mcgee 2011). TO allows for the reduction of up to 70% of the volume of concrete to support a given structure (Sondergaard & Dom...

  6. Dissolvable microneedle fabrication using piezoelectric dispensing technology. (United States)

    Allen, Evin A; O'Mahony, Conor; Cronin, Michael; O'Mahony, Thomas; Moore, Anne C; Crean, Abina M


    Dissolvable microneedle (DMN) patches are novel dosage forms for the percutaneous delivery of vaccines. DMN are routinely fabricated by dispensing liquid formulations into microneedle-shaped moulds. The liquid formulation within the mould is then dried to create dissolvable vaccine-loaded microneedles. The precision of the dispensing process is critical to the control of formulation volume loaded into each dissolvable microneedle structure. The dispensing process employed must maintain vaccine integrity. Wetting of mould surfaces by the dispensed formulation is also an important consideration for the fabrication of sharp-tipped DMN. Sharp-tipped DMN are essential for ease of percutaneous administration. In this paper, we demonstrate the ability of a piezoelectric dispensing system to dispense picolitre formulation volumes into PDMS moulds enabling the fabrication of bilayer DMN. The influence of formulation components (trehalose and polyvinyl alcohol (PVA) content) and piezoelectric actuation parameters (voltage, frequency and back pressure) on drop formation is described. The biological integrity of a seasonal influenza vaccine following dispensing was investigated and maintained voltage settings of 30 V but undermined at higher settings, 50 and 80 V. The results demonstrate the capability of piezoelectric dispensing technology to precisely fabricate bilayer DMN. They also highlight the importance of identifying formulation and actuation parameters to ensure controlled droplet formulation and vaccine stabilisation. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Impact damage in woven fabric reinforced composites

    NARCIS (Netherlands)

    Akkerman, Remko; Warnet, Laurent; van der Ven, E.C.


    Very often, woven fabrics are used as the reinforcement in advanced composite materials. Although the resulting inplane stiffness is lower than of their unidirectional counterparts, the excellent drapability of these materials eases the production of more general doubly curved components. In

  8. Bulk metamaterials: Design, fabrication and characterization

    DEFF Research Database (Denmark)

    Andryieuski, Andrei; Malureanu, Radu; Alabastri, Alessandro


    Bulk metamaterials claim a lot of attention worldwide. We report about our activity and advances in design, fabrication and characterization of metal-dielectric composites with three-dimensional lattices. The nomenclature of designs exhibiting negative index behaviour in the near infrared includes...

  9. Fabrication and optical characterization of improved electroless ...

    African Journals Online (AJOL)

    Fabrication and optical characterization of improved electroless chemically deposited strontium fluoride (SrF2) thin films at 320K. ... Journal of the Nigerian Association of Mathematical Physics ... Other optical and solid state properties were calculated from the data and compared with other deposited thin films. Average ...

  10. Determining glacier flow direction from till fabrics (United States)

    Iverson, Neal R.


    Field and experimental data indicate that fabrics of sheared basal tills, based on particle orientations and on anisotropy of magnetic susceptibility, are inclined relative to the macroscopic plane of shear. As a result, if this plane is tilted with a transverse component, one of the longest-standing axioms of glacial geology-that particles in basal till are preferentially oriented parallel to the direction of shear-is not strictly true. The resultant correction to the shearing direction increases with the transverse and longitudinal components of shear-plane inclination and with the magnitude of the fabric inclination relative to the shear plane. Azimuthal corrections calculated herein range from being negligible to a few tens of degrees for reasonable ranges of shear-plane tilt. The past success of fabric azimuths as indicators of flow direction, despite the absence of this correction, likely reflects the clustering of shear planes about the horizontal in basal tills. However, on the flanks of accreting subglacial bedforms, shear-plane attitudes may well conform to the local bedform slope. As illustrated with hypothetical fabrics of drumlins and flutes, azimuthal corrections can in that case be sufficiently large and systematic to seriously affect interpretations of bedform genesis.

  11. Internal Backpressure for Terabit Switch Fabrics

    DEFF Research Database (Denmark)

    Fagertun, Anna Manolova; Ruepp, Sarah Renée; Rytlig, Andreas


    This paper proposes and analyzes the efficiency of novel backpressure schemes for Terabit switch fabrics. The proposed schemes aim at buffer optimization under uniform traffic distribution with Bernoulli packet arrival process. Results show that a reduction of the needed maximum buffer capacity w...... with up to 47% can be achieved with switch-internal backpressure mechanisms at the expense of a small control overhead....

  12. Fabrication of Environmentally Biodegradable Lignin Nanoparticles

    NARCIS (Netherlands)

    Frangville, C.; Rutkevicius, M.; Richter, A.P.; Velev, O.D.; Stoyanov, S.D.; Paunov, V.N.


    We developed a method for the fabrication of novel biodegradable nanoparticles (NPs) from lignin which are apparently non-toxic for microalgae and yeast. We compare two alternative methods for the synthesis of lignin NPs which result in particles of very different stability upon change of pH. The

  13. Fabrication of universal esthetic lingual button

    Directory of Open Access Journals (Sweden)

    Ramkishore Ratre


    Full Text Available Lingual buttons are used in many instances for labial, as well as lingual orthodontics. A simple method is demonstrated to fabricate the lingual buttons chair side. The buttons made are aesthetic as they are made from composite resin and can be successfully bonded anywhere on all tooth surfaces.

  14. Empowering academia through modern fabrication practices

    DEFF Research Database (Denmark)

    Padfield, Nicolas; Haldrup, Michael; Hobye, Mads

    We posit that modern fabrication and rapid prototyping practices can empower non-technical academic environments. For this to resonate with academic learning and research environments in a university context we must view FabLabs not only as machine parks but as creative environments, producing...

  15. Wound dressing based on nonwoven viscose fabrics. (United States)

    Abou-Okeil, A; Sheta, A M; Amr, A; Ali, Marwa A


    Nonwoven viscose fabric was treated with chitosan/polyvinyl alcohol (PVA) using pad-dry method, using different concentrations of chitosan and PVA. Increasing the amount of PVA leads to increasing of air permeability. Water permeability increased by increasing the amount of PVA to 2 ml (10% solution) then decreased by any increase of the quantity of PVA solution. Roughness increased with increasing the amount of 10% PVA solution. It is shown that roughness, water and air permeability increased with increasing the chitosan concentration. Antibacterial properties was increased with increasing PVA/or chitosan concentration. The chitosan/PVA treated nonwoven viscose fabric was immersed in a solution of Ag nanoparticles. The chitosan/PVA/Ag nanoparticles treated nonwoven fabrics were used as wound dressings on French white Bouscat rabbits, with age ranged from 1 to 2 years. A complete healing was achieved using wound dressing consists of nonwoven viscose fabric treated with chitosan/PVA/Ag nanoparticles after 21 days. The histopathological examination confirmed the complete re-epithelialization and averagely thick epidermis formation. Copyright © 2012 Elsevier Ltd. All rights reserved.

  16. Tunable metamaterials fabricated by fiber drawing

    DEFF Research Database (Denmark)

    Fleming, Simon; Stefani, Alessio; Tang, Xiaoli


    We demonstrate a practical scalable approach to the fabrication of tunable metamaterials. Designed for terahertz (THz) wavelengths, the metamaterial is comprised of polyurethane filled with an array of indium wires using the well-established fiber drawing technique. Modification of the dimensions...

  17. Technological aspects of gaseous pixel detectors fabrication

    NARCIS (Netherlands)

    Blanco Carballo, V.M.; Salm, Cora; Smits, Sander M.; Schmitz, Jurriaan; Melai, J.; Chefdeville, M.A.; van der Graaf, H.


    Integrated gaseous pixel detectors consisting of a metal punctured foil suspended in the order of 50μm over a pixel readout chip by means by SU-8 insulating pillars have been fabricated. SU-8 is used as sacrificial layer but metallization over uncrosslinked SU-8 presents adhesion and stress

  18. Method of fabrication of anchored nanostructure materials (United States)

    Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei


    Methods for fabricating anchored nanostructure materials are described. The methods include heating a nano-catalyst under a protective atmosphere to a temperature ranging from about C. to about C. and contacting the heated nano-catalysts with an organic vapor to affix carbon nanostructures to the nano-catalysts and form the anchored nanostructure material.

  19. Fabrication and characterization of woodpile structures

    DEFF Research Database (Denmark)

    Zalkovskij, Maksim; Malureanu, Radu; Andryieuski, Andrei


    In this paper we present the whole fabrication and characterization cycle for obtaining 3D metal-dielectric woodpile structures. The optical properties of these structures have been measured using different setups showing the need of considering e.g. border effects when planning their use in real...


    A study was conducted to evaluate the emissions of perchloroethylene (tetrachloroethylene) from dry cleaned fabrics to determine: (a) how the introduction of fresh dry cleaning into a home affects the indoor concentration of perchloroethylene, and (b) the effectiveness of ‘airing...

  1. Fabrication and characterization of porous hydroxyapatite ocular ...

    Indian Academy of Sciences (India)


    areas of medicine (Aoki et al 1987; Grote 1987; Shin et al 1992) also. The use of hydroxyapatite as an ocular .... the experimental error, throughout the whole process of fabrication. The median particle size of HAp powder used ... per medication and resolution took place within the 12th post-operative day (figures 9 a–d).

  2. All NbN tunnel junction fabrication (United States)

    Leduc, H. G.; Khanna, S. K.; Stern, J. A.


    The development of SIS tunnel junctions based on NbN for mixer applications in the submillimeter range is reported. The unique technological challenges inherent in the development of all refractory-compound superconductor-based tunnel junctions are highlighted. Current deposition and fabrication techniques are discussed, and the current status of all-NbN tunnel junctions is reported.

  3. Flexible Thermoelectric Generators on Silicon Fabric

    KAUST Repository

    Sevilla, Galo T.


    In this work, the development of a Thermoelectric Generator on Flexible Silicon Fabric is explored to extend silicon electronics for flexible platforms. Low cost, easily deployable plastic based flexible electronics are of great interest for smart textile, wearable electronics and many other exciting applications. However, low thermal budget processing and fundamentally limited electron mobility hinders its potential to be competitive with well established and highly developed silicon technology. The use of silicon in flexible electronics involve expensive and abrasive materials and processes. In this work, high performance flexible thermoelectric energy harvesters are demonstrated from low cost bulk silicon (100) wafers. The fabrication of the micro- harvesters was done using existing silicon processes on silicon (100) and then peeled them off from the original substrate leaving it for reuse. Peeled off silicon has 3.6% thickness of bulk silicon reducing the thermal loss significantly and generating nearly 30% more output power than unpeeled harvesters. The demonstrated generic batch processing shows a pragmatic way of peeling off a whole silicon circuitry after conventional fabrication on bulk silicon wafers for extremely deformable high performance integrated electronics. In summary, by using a novel, low cost process, this work has successfully integrated existing and highly developed fabrication techniques to introduce a flexible energy harvester for sustainable applications.

  4. Precision Metal Fabrication. Florida Vocational Program Guide. (United States)

    University of South Florida, Tampa. Dept. of Adult and Vocational Education.

    This guide identifies considerations in the organization, operation, and evaluation of secondary and postsecondary vocational education programs. It contains both a vocational program guide and Career Merit Achievement Plan (Career MAP) for precision metal fabrication. The guide contains the following sections: occupational description; program…

  5. Metal Fabrication. Florida Vocational Program Guide. (United States)

    University of South Florida, Tampa. Dept. of Adult and Vocational Education.

    This guide identifies considerations in the organization, operation, and evaluation of secondary and postsecondary vocational education programs. It contains both a vocational program guide and Career Merit Achievement Plan (Career MAP) for metal fabrication. The guide contains the following sections: occupational description; program content…

  6. Improved Sound Absorption Performance of Nonwoven Fabric using Fabric Facing and Air Back Cavity

    Directory of Open Access Journals (Sweden)

    Ismail Ahmad Yusuf


    Full Text Available This paper presents the improvement methods to increase sound absorption performance of polyethylene based nonwoven fabric (PNF. The methods are placing a woven fabric in front of the sample as well as providing air cavity behind the sample. The samples were experimentally tested in an impedance tube based on ISO 10354-2:2001 whereby two microphones are used and the transfer matrix methods are employed. From the results, it can be seen that placing front woven fabric effectively increases sound absorption performance. Moreover, introducing air cavity gap behind the sample is also found to be more significant to increase sound absorption.

  7. Fuel Fabrication Capability Research and Development Plan

    Energy Technology Data Exchange (ETDEWEB)

    Senor, David J.; Burkes, Douglas


    The purpose of this document is to provide a comprehensive review of the mission of the Fuel Fabrication Capability (FFC) within the Global Threat Reduction Initiative Convert Program, along with research and development (R&D) needs that have been identified as necessary to ensuring mission success. The design and fabrication of successful nuclear fuels must be closely linked endeavors. Therefore, the overriding motivation behind the FFC R&D program described in this plan is to foster closer integration between fuel design and fabrication to reduce programmatic risk. These motivating factors are all interrelated, and progress addressing one will aid understanding of the others. The FFC R&D needs fall into two principal categories, 1) baseline process optimization, to refine the existing fabrication technologies, and 2) manufacturing process alternatives, to evaluate new fabrication technologies that could provide improvements in quality, repeatability, material utilization, or cost. The FFC R&D Plan examines efforts currently under way in regard to coupon, foil, plate, and fuel element manufacturing, and provides recommendations for a number of R&D topics that are of high priority but not currently funded (i.e., knowledge gaps). The plan ties all FFC R&D efforts into a unified vision that supports the overall Convert Program schedule in general, and the fabrication schedule leading up to the MP-1 and FSP-1 irradiation experiments specifically. The fabrication technology decision gates and down-selection logic and schedules are tied to the schedule for fabricating the MP-1 fuel plates, which will provide the necessary data to make a final fuel fabrication process down-selection. Because of the short turnaround between MP-1 and the follow-on FSP-1 and MP-2 experiments, the suite of specimen types that will be available for MP-1 will be the same as those available for FSP-1 and MP-2. Therefore, the only opportunity to explore parameter space and alternative processing

  8. Numerical analysis of granular soil fabrics (United States)

    Torbahn, L.; Huhn, K.


    Soil stability strongly depends on the material strength that is in general influenced by deformation processes and vice versa. Hence, investigation of material strength is of great interest in many geoscientific studies where soil deformations occur, e.g. the destabilization of slopes or the evolution of fault gouges. Particularly in the former case, slope failure occurs if the applied forces exceed the shear strength of slope material. Hence, the soil resistance or respectively the material strength acts contrary to deformation processes. Besides, geotechnical experiments, e.g. direct shear or ring shear tests, suggest that shear resistance mainly depends on properties of soil structure, texture and fabric. Although laboratory tests enable investigations of soil structure and texture during shear, detailed observations inside the sheared specimen during the failure processes as well as fabric effects are very limited. So, high-resolution information in space and time regarding texture evolution and/or grain behavior during shear is refused. However, such data is essential to gain a deeper insight into the key role of soil structure, texture, etc. on material strength and the physical processes occurring during material deformation on a micro-scaled level. Additionally, laboratory tests are not completely reproducible enabling a detailed statistical investigation of fabric during shear. So, almost identical setups to run methodical tests investigating the impact of fabric on soil resistance are hard to archive under laboratory conditions. Hence, we used numerical shear test experiments utilizing the Discrete Element Method to quantify the impact of different material fabrics on the shear resistance of soil as this granular model approach enables to investigate failure processes on a grain-scaled level. Our numerical setup adapts general settings from laboratory tests while the model characteristics are fixed except for the soil structure particularly the used

  9. Assessment of Internal Fabric of Particulate Materials (United States)

    Alshibi, Khalid A.


    Particle arrangement and distribution within a soil matrix has long been recognized as having significant influence on the mechanical behavior of cohesionless soils. It is well known that two soil specimens having the same grain type (e.g., quartz, feldspar, etc.), same grain size distribution and relative density (or void ratio) can display completely different mechanical behavior. Because of the different fabric configurations in the otherwise similar specimens, they are likely to have different mechanical properties such as stress-strain response, anisotropy, dilatancy, etc. Soil Fabric is defined as the arrangement of particles, particle groups and associated pore space. In the literature, fabric analysis techniques are mainly classified as destructive (e.g., specimen stabilization, thin-sectioning, and microscopy), and nondestructive techniques (e.g., magnetic resonance imaging, ultrasonic testing, x-ray radiography, and computed tomography). Quantifying the void ratio and its distribution is the main parameter used to describe the fabric of particulate materials. This paper presents a comprehensive literature review of fabric analysis techniques applied to particulate materials. In addition, the results of a comprehensive investigation to quantify void ratio of sand specimens will be presented and discussed. The sand used in the experiments in a natural, uniform rounded to sub-rounded silica sand known as F-75 banding sand with mean particle size of 0.22 mm. Uniform specimens and specimens subjected to different axial-strain levels tested under triaxial and biaxial conditions are examined to evaluate void ratio evolution and its distribution using destructive thin-sectioning and nondestructive Computed Tomography (CT) techniques. Details of a new innovative polygon generation technique called Voronoi tessellation used to quantify void ratio of microscopic images of sand grains will be presented and compared to classical Oda's method. Finally, frequency

  10. A biomimic thermal fabric with high moisture permeability

    Directory of Open Access Journals (Sweden)

    Fan Jie


    Full Text Available Moisture comfort is an essential factor for functional property of thermal cloth, especially for thick thermal cloth, since thick cloth may hinder effective moisture permeation, and high moisture concentration in the micro-climate between skin and fabric would cause cold feeling. Here, we report a biomimic thermal fabric with excellent warm retention and moisture management properties. In this fabric, the warp yarn system constructs many tree-shaped channel nets in the thickness direction of the fabric. Experimental result indicates that the special hierarchic configuration of warp yarns endows the biomimic thermal fabric with a better warm retention and water vapor management properties compared with the traditional fabrics.

  11. Functional modification of Nylon fabrics based on noble metal nanoparticles (United States)

    Lin, Xia; Zou, Fan; Chen, Xinzhu; Tang, Bin


    In situ synthesis of gold nanoparticles was realized on Nylon fabrics through heat treatment with assistance of citrate. The synthesized gold nanoparticles imparted bright colors to Nylon fabrics due to its localized surface plasmon resonance (LSPR) features. Optical properties of the treated fabrics were analyzed by recording color strength (K/S) curves of fabrics. Scanning electron microscopy (SEM) was employed to observe the surface morphologies of Nylon fabrics with gold nanoparticles. The influence of pH value on the in situ synthesis of gold nanoparticles was discussed. Moreover, the coloration with gold nanoparticles improved the UV protection of Nylon fabrics.

  12. Wideband polarization splitter and rotator with large fabrication tolerance and simple fabrication process

    DEFF Research Database (Denmark)

    Ding, Yunhong; Ou, Haiyan; Peucheret, Christophe


    We propose and demonstrate a polarization splitter and rotator (PSR) built on a silicon-on-insulator platform. The PSR is constructed with a tapered waveguide followed by a 2×2 multimode interferometer and can be simply fabricated in a single lithography and etching step. A low insertion loss (....5  dB with minimum insertion loss of 0.6 dB) and a low polarization crosstalk (fabrication tolerance (>50  nm) are experimentally demonstrated....

  13. Solid freeform fabrication of biological materials (United States)

    Wang, Jiwen

    This thesis investigates solid freeform fabrication of biological materials for dental restoration and orthopedic implant applications. The basic approach in this study for solid freeform fabrication of biological materials is micro-extrusion of single or multiple slurries for 3D components and inkjet color printing of multiple suspensions for functionally graded materials (FGMs). Common issues associated with micro-extrusion and inkjet color printing are investigated. These common issues include (i) formulation of stable slurries with a pseudoplastic property, (ii) cross-sectional geometry of the extrudate as a function of the extrusion parameters, (iii) fabrication path optimization for extrusion process, (iv) extrusion optimization for multi-layer components, (v) composition control in functionally graded materials, and (vi) sintering optimization to convert the freeform fabricated powder compact to a dense body for biological applications. The present study clearly shows that the rheological and extrusion behavior of dental porcelain slurries depend strongly on the pH value of the slurry and extrusion conditions. A slurry with pseudoplastic properties is a basic requirement for obtaining extruded lines with rectangular cross-sections. The cross-sectional geometry of the extrudate is also strongly affected by extrusion parameters including the extrusion nozzle height, nozzle moving speed, extrusion rate, and critical nozzle height. Proper combinations of these extrusion parameters are necessary in order to obtain single line extrudates with near rectangular cross-sections and 3D objects with dimensional accuracy, uniform wall thickness, good wall uprightness, and no wall slumping. Based on these understandings, single-wall, multi-wall, and solid teeth have been fabricated via micro-extrusion of the dental slurry directly from a CAD digital model in 30 min. Inkjet color printing using stable Al2O3 and ZrO 2 aqueous suspensions has been developed to fabricate

  14. Superparamagnetic photocurable nanocomposite for the fabrication of microcantilevers

    DEFF Research Database (Denmark)

    Suter, M; Ergeneman, O; Zürcher, J


    We present a photocurable polymer composite with superparamagnetic characteristics for the fabrication of microcantilevers. Uniform distribution and low particle agglomeration (......We present a photocurable polymer composite with superparamagnetic characteristics for the fabrication of microcantilevers. Uniform distribution and low particle agglomeration (...

  15. Image Segmentation Applied to the Analysis of Fabric Textures


    Sparavigna, Amelia Carolina


    International audience; In this work, we are proposing the use of image segmentation to the analysis of the textures of fabrics, with the aim of applying this approach to a fabric fault detection based on image processing.

  16. Functional finishing of cotton fabrics using silver nanoparticles. (United States)

    Vigneshwaran, N; Kathe, A A; Varadarajan, P V; Nachane, R P; Balasubramanya, R H


    We have reported a novel in situ synthesis protocol for silver nanoparticles onto cotton fabrics. Here, cotton fabric immersed in silver nitrate solution is autoclaved at 15 psi, 121 degrees C for 15 min. At this temperature and pressure, the aldehyde terminal of starch (residual size material on cotton fabric) reduced the silver nitrate to silver metal and simultaneously stabilized the nanoparticles on fabric itself. The UV-visible absorption spectrum of both cotton fabrics and bath solution showed a typical absorption peak at 420 nm corresponding to the surface plasmon resonance of silver nanoparticles. With the help of transmission electron micrographs, the average size of the dislodged silver nanoparticles in water is calculated to be 20.9 +/- 13.7 nm. This silver nanoparticles impregnated cotton fabrics showed excellent antibacterial activity against Staphylococcus aureus and bacteriostasis activity against Klebsiella pneumoniae. Also, silver nanoparticles impregnated fabrics expressed significant UV-protection capability in comparison with the untreated fabrics.

  17. Adaptive Control of Freeze-Form Extrusion Fabrication Processes (Preprint)

    National Research Council Canada - National Science Library

    Zhao, Xiyue; Landers, Robert G; Leu, Ming C


    Freeze-form Extrusion Fabrication (FEF) is an additive manufacturing process that extrudes high solids loading aqueous ceramic pastes in a layer-by-layer fashion below the paste freezing temperature for component fabrication...

  18. Modelling, fabrication and characterisation of THz fractal meta-materials

    DEFF Research Database (Denmark)

    Xiao, S.; Zhou, L.; Malureanu, Radu


    We present theoretical predictions, fabrication procedure and characterisation results of fractal metamaterials for the THz frequency range. The characterisation results match well the predicted response thus validating both the fabrication procedure as well as the simulation one. Such systems show...

  19. Fabrication and characterization of an electrostatic contraction beams micromotor

    NARCIS (Netherlands)

    Sarajlic, Edin; Berenschot, Johan W.; Tas, Niels Roelof; Fujita, H.; Krijnen, Gijsbertus J.M.; Elwenspoek, Michael Curt


    We report on fabrication and experimental characterization of an electrostatic contraction beams motor that exhibits both reliable operation and high performance haracteristics. This electrostatic linear stepper micromotor is fabricated in a single polysilicon layer combining vertical trench

  20. ProtoCology : Integrating modular robotics and non standard fabrication

    NARCIS (Netherlands)

    Friedrich, H.C.


    Modular robotics and architectural designs built from CNC-fabricated unique components are two emergent research areas in which technologies such as integrated parametric design and fabrication, digital control and mechatronics affect construction and (re) configuration of built environments. These

  1. Verifying Deadlock-Freedom of Communication Fabrics (United States)

    Gotmanov, Alexander; Chatterjee, Satrajit; Kishinevsky, Michael

    Avoiding message dependent deadlocks in communication fabrics is critical for modern microarchitectures. If discovered late in the design cycle, deadlocks lead to missed project deadlines and suboptimal design decisions. One approach to avoid this problem is to get high level of confidence on an early microarchitectural model. However, formal proofs of liveness even on abstract models are hard due to large number of queues and distributed control. In this work we address liveness verification of communication fabrics described in the form of high-level microarchitectural models which use a small set of well-defined primitives. We prove that under certain realistic restrictions, deadlock freedom can be reduced to unsatisfiability of a system of Boolean equations. Using this approach, we have automatically verified liveness of several non-trivial models (derived from industrial microarchitectures), where state-of-the-art model checkers failed and pen and paper proofs were either tedious or unknown.

  2. Gel Fabrication of Molybdenum “Beads”

    Energy Technology Data Exchange (ETDEWEB)

    Lowden, Richard Andrew [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Armstrong, Beth L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division; Cooley, Kevin M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States). Materials Science and Technology Division


    Spherical molybdenum particles or “beads” of various diameters are of interest as feedstock materials for the additive manufacture of targets and assemblies used in the production of 99Mo medical isotopes using accelerator technology. Small metallic beads or ball bearings are typically fabricated from wire; however, small molybdenum spheres cannot readily be produced in this manner. Sol-gel processes are often employed to produce small dense microspheres of metal oxides across a broad diameter range that in the case of molybdenum could be reduced and sintered to produce metallic spheres. These Sol-gel type processes were examined for forming molybdenum oxide beads; however, the molybdenum trioxide was chemically incompatible with commonly used gelation materials. As an alternative, an aqueous alginate process being assessed for the fabrication of oxide spheres for catalyst applications was employed to form molybdenum trioxide beads that were successfully reduced and sintered to produce small molybdenum spheres.

  3. Methods for fabrication of flexible hybrid electronics (United States)

    Street, Robert A.; Mei, Ping; Krusor, Brent; Ready, Steve E.; Zhang, Yong; Schwartz, David E.; Pierre, Adrien; Doris, Sean E.; Russo, Beverly; Kor, Siv; Veres, Janos


    Printed and flexible hybrid electronics is an emerging technology with potential applications in smart labels, wearable electronics, soft robotics, and prosthetics. Printed solution-based materials are compatible with plastic film substrates that are flexible, soft, and stretchable, thus enabling conformal integration with non-planar objects. In addition, manufacturing by printing is scalable to large areas and is amenable to low-cost sheet-fed and roll-to-roll processes. FHE includes display and sensory components to interface with users and environments. On the system level, devices also require electronic circuits for power, memory, signal conditioning, and communications. Those electronic components can be integrated onto a flexible substrate by either assembly or printing. PARC has developed systems and processes for realizing both approaches. This talk presents fabrication methods with an emphasis on techniques recently developed for the assembly of off-the-shelf chips. A few examples of systems fabricated with this approach are also described.

  4. General strategy for fabricating thoroughly mesoporous nanofibers

    KAUST Repository

    Hou, Huilin


    Recently, preparation of mesoporous fibers has attracted extensive attentions because of their unique and broad applications in photocatalysis, optoelectronics, and biomaterials. However, it remains a great challenge to fabricate thoroughly mesoporous nanofibers with high purity and uniformity. Here, we report a general, simple and cost-effective strategy, namely, foaming-assisted electrospinning, for producing mesoporous nanofibers with high purity and enhanced specific surface areas. As a proof of concept, the as-fabricated mesoporous TiO2 fibers exhibit much higher photocatalytic activity and stability than both the conventional solid counterparts and the commercially available P25. The abundant vapors released from the introduced foaming agents are responsible for the creation of pores with uniform spatial distribution in the spun precursor fibers. The present work represents a critically important step in advancing the electrospinning technique for generating mesoporous fibers in a facile and universal manner.

  5. Inverted process for graphene integrated circuits fabrication. (United States)

    Lv, Hongming; Wu, Huaqiang; Liu, Jinbiao; Huang, Can; Li, Junfeng; Yu, Jiahan; Niu, Jiebin; Xu, Qiuxia; Yu, Zhiping; Qian, He


    CMOS compatible 200 mm two-layer-routing technology is employed to fabricate graphene field-effect transistors (GFETs) and monolithic graphene ICs. The process is inverse to traditional Si technology. Passive elements are fabricated in the first metal layer and GFETs are formed with buried gate/source/drain in the second metal layer. Gate dielectric of 3.1 nm in equivalent oxide thickness (EOT) is employed. 500 nm-gate-length GFETs feature a yield of 80% and fT/fmax = 17 GHz/15.2 GHz RF performance. A high-performance monolithic graphene frequency multiplier is demonstrated using the proposed process. Functionality was demonstrated up to 8 GHz input and 16 GHz output. The frequency multiplier features a 3 dB bandwidth of 4 GHz and conversion gain of -26 dB.

  6. Fabrication Process of Rounded Damped Detuned Structure

    CERN Document Server

    Hitomi, N; Higashi, Y; Higo, T; Koike, S; Suzuki, T; Takata, K; Takatomi, T; Toge, T; Watanabe, Y


    Following the successful design and fabrication of Damped Detuned Structures (DDS), the JLC/NLC linear collider project advanced to Rounded Damped Detuned Structures (RDDS) with curved cross section of the cavity shape for increased shunt impedance. Various advanced techniques for fabricating RDDS1 disks comparing to those for DDS were established to satisfy the dimension accuracy of +-1 micron over the entire surface made by ultra-precision turning. These disks were assembled with almost the same stacking and bonding jigs and processes as those of DDS3 assembly. In consequence, the assembly showed little disk-to-disk misalignment within 1 micron before and after the process. Though, it had 200 micron smooth bowing, which was subsequently corrected as DDS3, and flares at both ends.

  7. Reforming Shapes for Material-aware Fabrication

    KAUST Repository

    Yang, Yongliang


    © 2015 The Eurographics Association and John Wiley & Sons Ltd. Published by John Wiley & Sons Ltd. As humans, we regularly associate shape of an object with its built material. In the context of geometric modeling, however, this inter-relation between form and material is rarely explored. In this work, we propose a novel data-driven reforming (i.e.; reshaping) algorithm that adapts an input multi-component model for a target fabrication material. The algorithm adapts both the part geometry and the inter-part topology of the input shape to better align with material-aware fabrication requirements. As output, we produce the reshaped model along with respective part dimensions and inter-part junction specifications. We evaluate our algorithm on a range of man-made models and demonstrate a variety of model reshaping examples focusing only on metal and wooden materials.

  8. Conceptual design study of advanced fuel fabrication systems

    Energy Technology Data Exchange (ETDEWEB)

    Ken-ya, Tanaka; Shusaku, Kono; Kiyoshi, Ono [Japan Nuclear Cycle Development JNC, Fuel Fabrication System Group, O-Arai Engineering Center, Ibaraki (Japan)


    The fuel fabrication plant images based on the advanced equipment with availability to operate in hot-cell facility are constructed. The characteristics of each fuel fabrication system for economical and environmental are evaluated roughly. The advanced fuel fabrication routes such as simplified pelletizing, vibration compaction and casting process would have the potential for reducing plant construction cost and minimizing the radioactive waste generated from fuel fabrication process. (author)

  9. Development of Partial Tubular Flat Knitting Fabric Composite Preform

    Directory of Open Access Journals (Sweden)

    Jiang Wei Qing


    Full Text Available After building some structures of partial tubular flat knitting fabric composite preform, the influencing factor on tubular section was analyzed and the fabric was knitted selectively. The partial tubular flat knitting fabric composite preform were Knitted by changing different yarn, row number and two-sided partial tubular flat knitting fabric. Multilayer sheet would be got after hot pressing and it has big market prospects and good application value.

  10. Potential Use of Geotechnical Fabric in Airfield Runway Design. (United States)


    Company. b. Tvpar 3401 - a nonwoven , heat-bonded polypropylene fabric produced by E. I. DuPont De Nemours & Company. c. Mirafi 50OX - a woven, split tape...for geotechnical fabric include ieofabric, filter 3 cloth, geotextile, and civil engineering fabric. Approximately 50 dif- ferent geotechnical...fabrics are commerciall- ivailable in the United States, in both woven and nonwoven styles and in weights from less than 3 oz/sq yd LO over 26 oz/sq yd

  11. Multifunctional non-woven fabrics of interfused graphene fibres


    Li, Zheng; Xu, Zhen; Liu, Yingjun; Wang, Ran; Gao, Chao


    Carbon-based fibres hold promise for preparing multifunctional fabrics with electrical conductivity, thermal conductivity, permeability, flexibility and lightweight. However, these fabrics are of limited performance mainly because of the weak interaction between fibres. Here we report non-woven graphene fibre fabrics composed of randomly oriented and interfused graphene fibres with strong interfibre bonding. The all-graphene fabrics obtained through a wet-fusing assembly approach are porous a...

  12. Reverse-symmetry waveguides: Theory and fabrication

    DEFF Research Database (Denmark)

    Horvath, R.; Lindvold, Lars René; Larsen, N.B.


    We present an extensive theoretical analysis of reverse-symmetry waveguides with special focus on their potential application as sensor components in aqueous media and demonstrate a novel method for fabrication of such waveguides. The principle of reverse symmetry is based on making the refractiv...... has the advantage of deeper penetration of the evanescent electromagnetic field into the cover medium, theoretically permitting higher sensitivity to analytes compared to traditional waveguide designs. We present calculated sensitivities and probing depths of conventional and reverse...

  13. Fabricate-On-Demand Vacuum Insulating Glazings

    Energy Technology Data Exchange (ETDEWEB)

    McCamy, James W. [PPG Industries, Inc., Pittsburgh, PA (United States)


    PPG proposed to design a fabricate-on-demand manufacturing process to overcome the cost and supply chain issues preventing widespread adoption of vacuum insulated glazing (VIG) units. To do so, we focused on improving three areas of VIG manufacturing that drive high costs and limit the ability for smaller manufacturers to enter the market: edge sealing, pillar design/placement, and evacuating the VIG.

  14. Design of the Target Fabrication Tritium Laboratory

    Energy Technology Data Exchange (ETDEWEB)

    Sherohman, J.W.; Roberts, D.H.; Levine, B.H.


    The design of the Target Fabrication Tritium Laboratory for deuterium-tritium fuel processing for laser fusion targets has been accomplished with the intent of providing redundant safeguard systems. The design of the tritium laboratory is based on a combination of tritium handling techniques that are currently used by experienced laboratories. A description of the laboratory in terms of its interrelated processing systems is presented to provide an understanding of the design features for safe operation.

  15. Improving ASIC Reuse with Embedded FPGA Fabrics (United States)


    applications. This fabric is automatically generated from a high-level architecture specification, synthesized to existing standard-cell libraries , and laid...those that can readily be implemented with standard cell libraries , have been proposed as an alternative to the hard FPGA layouts. In this paper...reconfigurable upon power up and that its configuration bits are stored in shift register logic, compatible with standard cell library implementation

  16. Ultrasonic Fabrication of Metallic Nanomaterials and Nanoalloys (United States)

    Shchukin, Dmitry G.; Radziuk, Darya; Möhwald, Helmuth


    This review demonstrates the potential of sonochemistry to become a valuable tool for nanotechnology through composite fabrication if the underlying complex processes are understood and controlled. We show that control of cavitation requires control of interfaces at the microsecond timescale, and a diversity of phenomena is observed at the cavitation interface using different surfactants. Concrete examples show that it is possible to prepare nonequilibrium mono- and multicomponent metallic nanostructures that possess properties considerably different from those of nanostructures prepared by conventional methods.

  17. Magnetic Nanoparticles From Fabrication to Clinical Applications

    CERN Document Server

    Thanh, Nguyen TK


    Offering the latest information in magnetic nanoparticle (MNP) research, Magnetic Nanoparticles: From Fabrication to Clinical Applications provides a comprehensive review, from synthesis, characterization, and biofunctionalization to clinical applications of MNPs, including the diagnosis and treatment of cancers. This book, written by some of the most qualified experts in the field, not only fills a hole in the literature, but also bridges the gaps between all the different areas in this field. Translational research on tailored magnetic nanoparticles for biomedical applications spans a variet

  18. Domainal fabric development, associated microstructures and PT ...

    Indian Academy of Sciences (India)

    The granulite complex around Jenapore, Orissa, Eastern Ghats granulite belt, bears the imprint of two episodes of strong deformation (D1 and D2) attended with foliation (fabric) development (S1 and S2). Two distinct metamorphic events at P-T conditions of ∼900° C at ∼9 kbar and ∼600° C at ∼6 kbar are correlated with ...

  19. Method to fabricate hollow microneedle arrays

    Energy Technology Data Exchange (ETDEWEB)

    Kravitz, Stanley H. (Placitas, NM); Ingersoll, David (Albuquerque, NM); Schmidt, Carrie (Los Lunas, NM); Flemming, Jeb (Albuquerque, NM)


    An inexpensive and rapid method for fabricating arrays of hollow microneedles uses a photoetchable glass. Furthermore, the glass hollow microneedle array can be used to form a negative mold for replicating microneedles in biocompatible polymers or metals. These microneedle arrays can be used to extract fluids from plants or animals. Glucose transport through these hollow microneedles arrays has been found to be orders of magnitude more rapid than natural diffusion.

  20. Pneumatic splints: fabrication and use in neurorehabilitation. (United States)

    Taly, A B; Nair, K P S; Murali, T; Wankade, M


    Asymmetrical tone and weakness in antagonistic muscles often result in misalignment of joint, contractures and deformities. Traditional static splints used to prevent these complications are expensive, have to be custom made and cannot be used when deformities are marked. Authors describe fabrication and use of pneumatic splints, which are economic, safe and easy to apply. These splints have wide application in the management of common medical problems in neurological rehabilitation like hypotension, edema, pain, spasticity and early deformities.

  1. Fabrication Of Fiber-Optic Waveguide Coupler (United States)

    Goss, Willis; Nelson, Mark D.; Mclauchlan, John M.


    Technique for making four-port, single-mode fiber-optic waveguide couplers requires no critically-precise fabrication operations or open-loop processes. Waveguide couplers analogous to beam-splitter prisms. Essential in many applications that require coherent separation or combination of two waves; for example, for interferometric purposes. Components of optical waveguide coupler held by paraffin on microscope slide while remaining cladding of two optical fibers fused together by arc welding.

  2. Fabrication and size control of Ag nanoparticles

    Directory of Open Access Journals (Sweden)

    M Farbod


    Full Text Available  The objective of this research was to fabricate Ag nanoparticles and control their sizes. Colloidal Ag nanoparticles with particle size of 30 nm were prepared by dissolving AgNO3 in ethanol and through the chemical reduction of Ag+ in alcohol solution. To control the nanoparticle size, different samples were fabricated by changing the AgNO3 and stabilizer concentrations and the effects of different factors on the shape and size of nanoparticles were investigated. The samples were characterized using SEM and EDX analysis. The results showed that by increasing the AgNO3 concentration, the average size of nanoparticles increases and nanoparticles lose their spherical shape. Also, we found that by using the stabilizer, it is possible to produce stable nanoparticles but increasing the stabilizer concentration caused an increase in size of nanoparticles. Fabrication of nanoparticles without using stabilizer was achieved but the results showed the nanoparticles size had a growth of 125 nm/h in the alcoholic media.

  3. Fabrication of brittle materials -- current status

    Energy Technology Data Exchange (ETDEWEB)

    Scattergood, R.O.


    The research initiatives in the area of precision fabrication will be continued in the upcoming year. Three students, T. Bifano (PhD), P. Blake (PhD) and E. Smith (MS), finished their research programs in the last year. Sections 13 and 14 will summarize the essential results from the work of the Materials Engineering students Blake and Smith. Further details will be presented in forthcoming publications that are now in preparation. The results from Bifano`s thesis have been published in adequate detail and need not be summarized further. Three new students, S. Blackley (MS), H. Paul (PhD), and S. Smith (PhD) have joined the program and will continue the research efforts in precision fabrication. The programs for these students will be outlined in Sections 15 and 16. Because of the success of the earlier work in establishing new process models and experimental techniques for the study of diamond turning and diamond grinding, the new programs will, in part, build upon the earlier work. This is especially true for investigations concerned with brittle materials. The basic understanding of material response of nominally brittle materials during machining or grinding operations remains as a challenge. The precision fabrication of brittle materials will continue as an area of emphasis for the Precision Engineering Center.

  4. Wafer-scale micro-optics fabrication (United States)

    Voelkel, Reinhard


    Micro-optics is an indispensable key enabling technology for many products and applications today. Probably the most prestigious examples are the diffractive light shaping elements used in high-end DUV lithography steppers. Highly-efficient refractive and diffractive micro-optical elements are used for precise beam and pupil shaping. Micro-optics had a major impact on the reduction of aberrations and diffraction effects in projection lithography, allowing a resolution enhancement from 250 nm to 45 nm within the past decade. Micro-optics also plays a decisive role in medical devices (endoscopes, ophthalmology), in all laser-based devices and fiber communication networks, bringing high-speed internet to our homes. Even our modern smart phones contain a variety of micro-optical elements. For example, LED flash light shaping elements, the secondary camera, ambient light and proximity sensors. Wherever light is involved, micro-optics offers the chance to further miniaturize a device, to improve its performance, or to reduce manufacturing and packaging costs. Wafer-scale micro-optics fabrication is based on technology established by the semiconductor industry. Thousands of components are fabricated in parallel on a wafer. This review paper recapitulates major steps and inventions in wafer-scale micro-optics technology. The state-of-the-art of fabrication, testing and packaging technology is summarized.

  5. Shield Effect Of Functional Interlining Fabric

    Directory of Open Access Journals (Sweden)

    Šaravanja Bosiljka


    Full Text Available Electromagnetic interference (EMI have become very serious in a variety of different electronic equipments, such as personal computers (frequency at several GHz, mobile devices (0.9 – 2.4 GHz and similar. This imposes the need for setting boundaries for EM emission of electric and electronic devices in order to minimize the possibility of interference with radio and wireless communications. Functional textiles can offer protective properties against EM radiation. The aim of this study is to investigate the degree of protection against EM radiation provided by polyamide copper-coated interlining fabric before and after dry cleaning treatment. EM protection efficiency of the interlining functional fabric is explored on both sides at the frequencies of 0.9; 1.8; 2.1 and 2.4 GHz. The results obtained have shown that the interlining fabric has good protective properties against EM radiation, but after dry cleaning, treatment reduction is observed. Scanning electron microscopy micrographs of the interlining surface confirms shield effect decline due to degradation and firing of the copper layers during the process of dry cleaning.

  6. Fabrication of the CALDER light detectors (United States)

    Colantoni, I.; Bellini, F.; Cardani, L.; Casali, N.; Castellano, M. G.; Coppolecchia, A.; Cosmelli, C.; Cruciani, A.; D`Addabbo, A.; Di Domizio, S.; Martinez, M.; Tomei, C.; Vignati, M.


    CALDER (Cryogenic wide-Area Light Detectors with Excellent Resolution) is a project for the development of large area phonon mediated KIDs (Kinetic Inductance Detectors), for the detection of Cherenkov radiation emitted in TeO2 bolometers to search for neutrinoless double beta decay (0 νββ). The KIDs are superconducting detectors made of high quality factor superconducting resonators, which are coupled to a transmission line for signal readout. We designed and fabricated KIDs using aluminum. The Al thin films (40 nm) were evaporated on Si(100) high resistivity silicon wafers using an electron beam evaporator in a HV chamber. In this work we report the steps of the fabrication process. All devices are made in direct-write using Electron Beam Lithography (EBL), positive tone resist poly-methyl methacrylate (PMMA) and lift off process. In order to improve the sensitivity of the detectors we have started recently to use sub-stoichiometric TiN deposited by means of DC magnetron sputtering and we will optimize a different fabrication process.

  7. PMMA microlens array fabricated by indentation process (United States)

    Cirino, Giuseppe A.; Jasinevicius, Renato G.


    This work reports the fabrication of a PMMA-based spherical microlens array (MLA), targeting application of Shack-Hartmann wavefront sensor for lens characterization. The array present 10 by 10 elements, with f-number f/# = f/10 (1 mm diameter, 10 mm focal length). The fabrication method employs a computer-controlled mechanical indentation for the fabrication of an insert mold, and subsequent replication by injection molding on PMMA. After replication and de-molding, the PMMA surface containing the negative of the phase profile of the lens array was evaluated by optical profilometry technique, in terms of the surface quality as well as the replication fidelity. The RMS surface roughness level of approximately (λ/10) was found, considering operation in the visible range of spectrum. Optical characterization was based on the evaluation of the sharpness, FWHM, and maximum intensity, IMAX, values associated to the profiles of each of the 100 generated light spots, obtained in the back focal plane of the MLA. An average sharpness of FWHMAVG = 13.9 +/- 8% μm, and average maximum intensity of IMAX AVG = 0.72 +/- 7% a.u. was obtained.

  8. Fabrication of Microglass Nozzle for Microdroplet Jetting

    Directory of Open Access Journals (Sweden)

    Dan Xie


    Full Text Available An ejection aperture nozzle is the essential part for all microdrop generation techniques. The diameter size, the flow channel geometry, and fluid impedance are the key factors affecting the ejection capacity. A novel low-cost fabrication method of microglass nozzle involving four steps is developed in this work. In the first heating step, the glass pipette is melted and pulled. Then, the second heating step is to determine the tip cone angle and modify the flow channel geometry. The desired included angle is usually of 30~45 degrees. Fine grind can determine the exact diameter of the hole. Postheating step is the final process and it can reduce the sharpness of the edges of the hole. Micronozzles with hole diameters varying from 30 to 100 µm are fabricated by the homemade inexpensive and easy-to-operate setup. Hydrophobic treating method of microglass nozzle to ensure stable and accurate injection is also introduced in this work. According to the jetting results of aqueous solution, UV curing adhesive, and solder, the fabricated microglass nozzle can satisfy the need of microdroplet jetting of multimaterials.

  9. Light emitting fabric technologies for photodynamic therapy. (United States)

    Mordon, Serge; Cochrane, Cédric; Tylcz, Jean Baptiste; Betrouni, Nacim; Mortier, Laurent; Koncar, Vladan


    Photodynamic therapy (PDT) is considered to be a promising method for treating various types of cancer. A homogeneous and reproducible illumination during clinical PDT plays a determinant role in preventing under- or over-treatment. The development of flexible light sources would considerably improve the homogeneity of light delivery. The integration of optical fiber into flexible structures could offer an interesting alternative. This paper aims to describe different methods proposed to develop Side Emitting Optical Fibers (SEOF), and how these SEOF can be integrated in a flexible structure to improve light illumination of the skin during PDT. Four main techniques can be described: (i) light blanket integrating side-glowing optical fibers, (ii) light emitting panel composed of SEOF obtained by micro-perforations of the cladding, (iii) embroidery-based light emitting fabric, and (iv) woven-based light emitting fabric. Woven-based light emitting fabrics give the best performances: higher fluence rate, best homogeneity of light delivery, good flexibility. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Schottky barrier MOSFET systems and fabrication thereof (United States)

    Welch, J.D.


    (MOS) device systems-utilizing Schottky barrier source and drain to channel region junctions are disclosed. Experimentally derived results which demonstrate operation of fabricated N-channel and P-channel Schottky barrier (MOSFET) devices, and of fabricated single devices with operational characteristics similar to (CMOS) and to a non-latching (SRC) are reported. Use of essentially non-rectifying Schottky barriers in (MOS) structures involving highly doped and the like and intrinsic semiconductor to allow non-rectifying interconnection of, and electrical accessing of device regions is also disclosed. Insulator effected low leakage current device geometries and fabrication procedures therefore are taught. Selective electrical interconnection of drain to drain, source to drain, or source to source, of N-channel and/or P-channel Schottky barrier (MOSFET) devices formed on P-type, N-type and Intrinsic semiconductor allows realization of Schottky Barrier (CMOS), (MOSFET) with (MOSFET) load, balanced differential (MOSFET) device systems and inverting and non-inverting single devices with operating characteristics similar to (CMOS), which devices can be utilized in modulation, as well as in voltage controlled switching and effecting a direction of rectification. 89 figs.

  11. Plasma treatment of polyester fabric to impart the water repellency ...

    Indian Academy of Sciences (India)


    Nov 27, 2015 ... Polyester fabric is treated with DCDMS solution by two methods: dipping the fabric directly in DCDMS solution for different intervals and dipping the fabric in DCDMS solution after its exposure into RF plasma chamber for different durations at optimized exposure power conditions. The physical properties of ...

  12. Perceptions of Seshoeshoe fabric, naming and meanings of motifs ...

    African Journals Online (AJOL)

    Responses of participants showed that both the dress and fabric are popularly known as seshoeshoe. It was further found that the choice of the fabric has increased in the market due to the wide variety of motifs and colours although the quality of fabric has not improved. There are still problems encountered by dressmakers ...

  13. Flow resistance of textile materials. Part II: Multifilament Fabrics

    NARCIS (Netherlands)

    Gooijer, H.; Gooijer, H.; Warmoeskerken, Marinus; Groot Wassink, J.


    Part I of this series presented a new model for predicting the flow resistance of monofilament fabrics. In this part, the model is applied to the flow resistance of multi filament fabrics. Experiments show that flow resistance in multifilament fabrics can be modeled in general, but it appears that

  14. Effect of dichlorodimethylsilane on plasma-treated cotton fabric*

    Indian Academy of Sciences (India)

    Abstract. Cotton fabric was treated with dichlorodimethylsilane (DCDMS) solution by two methods. In the first method, the fabrics were directly dipped into DCDMS solu- tion for different time intervals and in the second method, the fabric was first subjected to radiofrequency (RF) plasma treatment for different durations and ...


    NARCIS (Netherlands)

    Maqsood, Muhammad


    This paper introduces a 3D woven fabric-based approach for the development of pressure switch. A fabric substrate, being elastic and extendable is very useful in addition to its high breaking strength and low cost. The developed resistive-type switch is based on the multilayer interlock 3D fabrics.

  16. Evaluation of Speedup and Expansion in Terabit Switch Fabrics

    DEFF Research Database (Denmark)

    Ruepp, Sarah Renée; Rytlig, Andreas; Berger, Michael Stübert


    This paper evaluates speedup and expansion in a multi-stage Terabit switch fabric. Single-stage switch fabrics, e.g. crossbar switches, are difficult to scale up to a Terabit system. Hence, a multi-stage switch fabric, where traffic can be distributed on different chips, offers a promising...

  17. Draping Double-Layer Woven Fabrics Onto Double-Curvature ...

    African Journals Online (AJOL)

    Draping woven fabrics to complex parts with double curvature leads to complex redistribution and reorientation of the yarns in composites reinforced with woven preforms. To reduce the risk of fabric tearing or wrinkling we propose to use double-layer woven fabrics. This paper presents a simulation model for draping

  18. Comparative Evaluation of the Effectiveness of some local Fabrics ...

    African Journals Online (AJOL)

    Ovic et (11., 1993, and. Ovie and Egborge, 2002), this study has shown that locally available local fabrics are good and inexpensive fabrics for zooplankton harvest. In particular, the local fabric, poplin can be employed even in field research, ...

  19. non-woven fabrics treated with bamboo activated charcoal

    African Journals Online (AJOL)



    Jun 21, 2012 ... Non-woven fabrics are commonly applied in medicine and healthcare, and its utilization could change from the reusable to disposable products. Non- woven fabrics are chiefly applied in medicine, healthcare and for filtering (Wang and He, 2007). Furthermore, the present study will be aimed at fabricating ...

  20. Comparison of compression properties of stretchable knitted fabrics and bi-stretch woven fabrics for compression garments

    NARCIS (Netherlands)

    Maqsood, Muhammad


    Stretchable fabrics have diverse applications ranging from casual apparel to performance sportswear and compression therapy. Compression therapy is the universally accepted treatment for the management of hypertrophic scarring after severe burns. Mostly stretchable knitted fabrics are used in

  1. Magnetic fabric of brittle fault rocks (United States)

    Pomella, Hannah


    The anisotropy of magnetic susceptibility (AMS) has been recognized as a highly sensitive indicator of rock fabric and is widely employed in the field of structural geology. Brittle faults are often characterized by fault breccia and gouge, fault rocks with clast-in-matrix textures. A noteworthy property of both gouge and breccia is the often observed presence of a fabric that is defined by the preferred orientation of clasts and grains in the matrix. In the very fine-grained gouge and in the matrix of the breccia the fabric is not visible in the field or in thin sections but can probably be detected by AMS analyses. For the present study different kinds of brittle fault rocks have been sampled on two faults with known tectonic settings, in order to allow for a structural interpretation of the measured AMS signal. The measurements were carried out with an AGICO MFK1-FA Kappabridge and a CS4 furnace apparatus at the Institute of Geology, University of Innsbruck. Fault gouge was sampled on the Naif fault located in the Southern Alps, E of Meran, South Tyrol, Italy. Along this fault the Permian Granodiorite overthrusts the Southalpine basement and its Permomesozoic cover. The Neoalpine thrust fault is characterised by a wide cataclastic zone and an up to 1 m thick fault gouge. The gouge was sampled using paleomagnetic sample boxes. Heating experiments indicate that the magnetic fabric is dominated by paramagnetic minerals (>95%). The samples provide a magnetic susceptibility in the range of +10*E-5 [SI]. The K-min axis of the magnetic ellipsoid corresponds approximately to the pol of the fault plane measured in the field. However the whole magnetic ellipsoid shows a variation in the inclination compared to the structural data. Fine-grained ultracataclasites were sampled on the Assergi fault, located in the Abruzzi Apennines, NE of L'Aquila, Italy. This normal fault was active in historical time and crosscuts limestones as well as talus deposits. An up to 20 cm thick

  2. A Novel Two-Step Method for Fabricating Silver Plating Cotton Fabrics

    Directory of Open Access Journals (Sweden)

    Hao Liu


    Full Text Available A novel two-step method was presented for fabricating silver plating cotton fabrics (SPCFs with high electrical conductivity and excellent washing fastness. First, polydopamine (PDA film was coated on the surface of cotton fabrics by in situ polymerization of dopamine, the silver ions in silver nitrate solution were reduced by the catechol groups of polydopamine, and silver nanoparticles were combined with polydopamine by covalent bond on the surface of cotton fabrics. Second, silver ions were reduced by glucose, and silver plating was coated on the surface. Subsequently, the properties of SPCFs were characterized by field emission scanning electron microscopy (FESEM, X-ray photoelectron spectroscopy (XPS and thermogravimetric analysis (TGA, and so forth. With the increasing of silver-ammonia solution concentration or dopamine concentration, the surface resistivity of SPCFs decreases and gradually stabilized. The surface resistivity of the SPCFs can reach 0.12±0.02 Ω, and electromagnetic shielding effectiveness (ESE of the SPCFs can reach 58.5±4.5 dB. Conductive fabrics have wide application prospect in many of fields, such as antibacterial, intelligent textiles, smart garments, electromagnetic shielding, and flexible sensors.

  3. Fabrication of semi-transparent superoleophobic thin film from fabrics and nanoparticle-based hierarchical structure

    Directory of Open Access Journals (Sweden)

    Nishizawa S.


    Full Text Available Superoleophobic thin films have many potential applications including fluid transfer, fluid power systems, stain resistant and antifouling materials, and microfluidics among others. Transparency is also desired with superhydrophobicity for their numerous applications; however transparency and oleophobicity are almost incompatible relationship with each other in the point of surface structure. Because oleophobicity required rougher structure at nano-micro scale than hydrophobicity, and these rough structure brings light scattering. So far, there is very few report of the compatible of transparency and superoleophobicity. In this report, we proposed the see-through type fabrics using the nanoparticle-based hierarchical structure thin film for improving both of oleophobicity and transparency. The vacant space between fibrils of fabrics has two important roles: the one is to through the light, another one is to introduce air layer to realize Cassie state of liquid droplet on thin film. To realize the low surface energy and nanoscale rough structure surface on fibrils, we used the spray method with perfluoroalkyl methacrylic copolymer (PMC, silica nano particles and volatile solvent. From the SEM image, the hierarchical structures of nanoparticle were formed uniformly on the fabrics. The transparency of thin film obtained was approximately 61% and the change of transparency between pre-coated fabrics and coated was 11%. From investigation of the surface wettability, the contact angles of oils (rapeseed oil and hexadecane and water droplet on the fabricated film were over 150 degree.

  4. One-pot fabrication and antimicrobial properties of novel PET nonwoven fabrics. (United States)

    Lin, Song; Wang, Zheng; Qi, Jian-cheng; Wu, Jin-hui; Tian, Tao; Hou, Li-li; Hao, Li-mei; Yang, Jing-quan


    Recently, with the ever-growing demand for healthy living, more and more research is focused on materials capable of killing harmful microorganisms around the world. It is believed that designing such protective materials for hygienic and biomedical applications can benefit people in professional areas and daily life. Thus, in this paper, one novel kind of antibacterial poly(ethylene terephthalate) (PET) nonwoven fabrics was conveniently one-pot prepared, with the combined immobilization of two biological antimicrobial agents, i.e. ε-polylysine and natamycin, by using the soft methacrylate nonwoven fabrics adhesives. Then, the antimicrobial activities of the functional fabrics were investigated by using the standard shaking-flask method, showing excellent antibacterial efficiency (AE) against both Escherichia coli (8099) and Staphylococcus aureus (ATCC 6538) (AE > 99.99%) compared with untreated PET nonwoven fabrics. The anti-bioaerosol tests also showed similar trends. Meantime, scanning electron microscopy analysis indicated that the bacteria on the antibacterial PET appeared to be partly bacteriolyzed and showed much less viability than those on the pristine ones. Moreover, the long residual biocidal action of such modified PET fabrics was also evaluated, and the antibacterial activity of antibacterial fibers was unaffected by the 3 month artificially accelerated aging. © 2011 IOP Publishing Ltd

  5. One-pot fabrication and antimicrobial properties of novel PET nonwoven fabrics

    Energy Technology Data Exchange (ETDEWEB)

    Lin Song; Wang Zheng; Qi Jiancheng; Wu Jinhui; Tian Tao; Hao Limei; Yang Jingquan [Institute of Medical Equipment, Academy of Military Medical Sciences, Tianjin 300161 (China); Hou Lili, E-mail: [National Bio-protection Engineering Center, Tianjin 300161 (China)


    Recently, with the ever-growing demand for healthy living, more and more research is focused on materials capable of killing harmful microorganisms around the world. It is believed that designing such protective materials for hygienic and biomedical applications can benefit people in professional areas and daily life. Thus, in this paper, one novel kind of antibacterial poly(ethylene terephthalate) (PET) nonwoven fabrics was conveniently one-pot prepared, with the combined immobilization of two biological antimicrobial agents, i.e. {epsilon}-polylysine and natamycin, by using the soft methacrylate nonwoven fabrics adhesives. Then, the antimicrobial activities of the functional fabrics were investigated by using the standard shaking-flask method, showing excellent antibacterial efficiency (AE) against both Escherichia coli (8099) and Staphylococcus aureus (ATCC 6538) (AE > 99.99%) compared with untreated PET nonwoven fabrics. The anti-bioaerosol tests also showed similar trends. Meantime, scanning electron microscopy analysis indicated that the bacteria on the antibacterial PET appeared to be partly bacteriolyzed and showed much less viability than those on the pristine ones. Moreover, the long residual biocidal action of such modified PET fabrics was also evaluated, and the antibacterial activity of antibacterial fibers was unaffected by the 3 month artificially accelerated aging.

  6. Preparation of ion-exchange fiber fabrics by electrospray deposition. (United States)

    Matsumoto, Hidetoshi; Wakamatsu, Yuji; Minagawa, Mie; Tanioka, Akihiko


    Ion-exchange fiber (IEF) fabrics were prepared by electrospray deposition (ESD) and post-deposition chemical modification of their surfaces. Nonwoven fibrous fabrics were obtained from the solutions of synthetic polymers-polystyrene (PS) and poly(4-vinylpyridine) (P4VP)-of various concentrations. The diameter of the fiber in the fabrics ranged from 600 nm to 1.70 microm. Cation- and anion-exchange fiber (CEF and AEF) fabrics were obtained from the sulfonation of PS fabrics and the quaternization of P4VP fabrics, respectively. These fabrics were thoroughly characterized by a series of techniques, such as scanning electron microscopy (SEM), permporometry, nitrogen adsorption measurements, and potentiometric titrations. The SEM images showed that the fabrics had a porous structure after their chemical modification. The mean pore size, porosity, and specific surface area of the flow-through pores were 1.67-3.53 microm, about 80%, and 13 m(2)/g, respectively. The ion-exchange capacity was in the range from 0.78 to 1.34 mmol/g. The AEF fabric, on the other hand, showed a high specific surface area, i.e., the Brunauer-Emmett-Teller (BET) surface area of 600 m(2)/g, due to the formation of much smaller pores on the surface of the fiber structure in the fabric. The secondary chemical modification of the nano-microfiber fabrics by ESD provides novel functional materials with a large adsorption capacity and a high catalytic activity.

  7. Relationship between the Physical Properties and Hand of Jean Fabric

    Directory of Open Access Journals (Sweden)

    Kawamura Atsushi


    Full Text Available We investigated the distinctive characteristics of jean fabrics (denim fabrics obtained from jeans and compared the physical properties and the hand. We used 13 kinds of jean fabric from commercial jeans and 26 other fabric types. The physical properties were measured using the Kawabata evaluation system, and the fabric hand was evaluated by 20 subjects using a semantic differential method. To characterise the hand of jean fabrics compared with other fabrics, we used principal component analysis and obtained three principal components. We found that jean fabrics were characterised by the second principal component, which was affected by feelings of thickness and weight. We further characterised the jean fabrics according to ‘softness & smoothness’ and ‘non-fullness’, depending on country of origin and type of manufacturer. The three principal components were analysed using multiple linear regression to characterise the components according to the physical properties. We explained the hand of fabrics including jean fabrics using its association with physical properties.

  8. Surface enhanced Raman scattering (SERS) fabrics for trace analysis

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Jun [National Engineering Laboratory for Advanced Yarn and Fabric Formation and Clean Production, Wuhan Textile University, Wuhan 430073 (China); Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials & Key Laboratory for the Synthesis and Application of Organic Functional Molecules, Ministry of Education & College of Chemistry & Chemical Engineering, Hubei University, Wuhan 430062 (China); Zhou, Ji [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials & Key Laboratory for the Synthesis and Application of Organic Functional Molecules, Ministry of Education & College of Chemistry & Chemical Engineering, Hubei University, Wuhan 430062 (China); Tang, Bin, E-mail: [National Engineering Laboratory for Advanced Yarn and Fabric Formation and Clean Production, Wuhan Textile University, Wuhan 430073 (China); Institute for Frontier Materials, Deakin University, Geelong, Victoria 3216 (Australia); Zeng, Tian; Li, Yaling [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials & Key Laboratory for the Synthesis and Application of Organic Functional Molecules, Ministry of Education & College of Chemistry & Chemical Engineering, Hubei University, Wuhan 430062 (China); Li, Jingliang [Institute for Frontier Materials, Deakin University, Geelong, Victoria 3216 (Australia); Ye, Yong, E-mail: [Hubei Collaborative Innovation Center for Advanced Organic Chemical Materials & Key Laboratory for the Synthesis and Application of Organic Functional Molecules, Ministry of Education & College of Chemistry & Chemical Engineering, Hubei University, Wuhan 430062 (China); Wang, Xungai [National Engineering Laboratory for Advanced Yarn and Fabric Formation and Clean Production, Wuhan Textile University, Wuhan 430073 (China); Institute for Frontier Materials, Deakin University, Geelong, Victoria 3216 (Australia)


    Highlights: • Gold nanoparticles are in-situ synthesized on silk fabrics by heating. • Flexible silk fabrics with gold nanoparticles are used for surface-enhanced Raman scattering (SERS). • SERS activities of silk fabrics with different gold contents are investigated. - Abstract: Flexible SERS active substrates were prepared by modification of silk fabrics with gold nanoparticles. Gold nanoparticles were in-situ synthesized after heating the silk fabrics immersed in gold ion solution. Localized surface plasmon resonance (LSPR) properties of the treated silk fabrics varied as the concentration of gold ions changed, in relation to the morphologies of gold nanoparticles on silk. In addition, X-ray diffraction (XRD) was used to observe the structure of the gold nanoparticle treated silk fabrics. The SERS enhancement effect of the silk fabrics treated with gold nanoparticles was evaluated by collecting Raman signals of different concentrations of p-aminothiophenol (PATP), 4-mercaptopyridine (4-MPy) and crystal violet (CV) solutions. The results demonstrate that the silk fabrics corresponding to 0.3 and 0.4 mM of gold ions possess high SERS activity compared to the other treated fabrics. It is suggested that both the gold content and morphologies of gold nanoparticles dominate the SERS effect of the treated silk fabrics.

  9. Elongation of fibers from highly viscous dextran solutions enables fabrication of rapidly dissolving drug carrying fabrics. (United States)

    Frampton, John P; Lai, David; Lounds, Maxwell; Chung, Kyeongwoon; Kim, Jinsang; Mansfield, John F; Takayama, Shuichi


    A simple method is presented for forming thread-like fibers from highly viscous dextran solutions. Based on the cohesive and adhesive forces between a dextran solution and the substrate to which it is applied, multiple fibers of approximately 10 μm in diameter can be elongated simultaneously. These fibers can be woven into multiple layers to produce fabrics of varying fiber orientations and mechanical properties. Various bioactive agents can be incorporated into the dextran solution prior to fiber formation, including hemostatic and antibiotic agents. Fabrics containing thrombin are capable of coagulating human platelet poor plasma in vitro. Fabrics containing antibiotics are capable of suppressing bacterial growth in a disk diffusion assay. These data suggest that this new material composed entirely of dextran has promise as a drug delivery component in wound dressings. © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Potassium-argon (argon-argon), structural fabrics (United States)

    Cosca, Michael A.; Rink, W. Jack; Thompson, Jereon


    Definition: 40Ar/39Ar geochronology of structural fabrics: The application of 40Ar/39Ar methods to date development of structural fabrics in geologic samples. Introduction: Structural fabrics develop during rock deformation at variable pressures (P), temperatures (T), fluid compositions (X), and time (t). Structural fabrics are represented in rocks by features such as foliations and shear zones developed at the mm to km scale. In ideal cases, the P-T-X history of a given structural fabric can be constrained using stable isotope, cation exchange, and/or mineral equilibria thermobarometry (Essene 1989). The timing of structural fabric development can be assessed qualitatively using geologic field observations or quantitatively using isotope-based geochronology. High-precision geochronology of the thermal and fluid flow histories associated with structural fabric development can answer fundamental geologic questions including (1) when hydrothermal fluids transported and deposited ore minerals, ...

  11. Rapsodie first core fabrication. 2. part: manufacture results; Fabrication du premier coeur de rapsodie. Deuxieme partie: resultats de fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Masselot, Y.; Bataller, S.; Ganivet, M.; Guillet, H.; Robillard, A.; Stosskopf, F. [Commissariat a l' Energie Atomique, Cadarache (France). Centre d' Etudes Nucleaires


    This report is the second in a series of three describing the processes, results and peculiar technical problems related to the manufacture of the first core of the fast reactor Rapsodie. It includes a critical study of the results obtained on the pellets, pins and sub-assemblies as compared with their specifications. By the way, the benefit of the linear mass concept as a quality test for a given manufacture is shown. At last performances and balance of the first two production runs are examined. (author) [French] Ce rapport est le second d'une serie de trois qui decrivent les procedes, les resultats et les problemes techniques particuliers de la fabrication du premier coeur de la pile a neutrons rapides RAPSODIE. Il comporte une etude critique des resultats obtenus pour les pastillles, les aiguilles et les assemblages combustibles, compares a leur specifications. A cette occasion, on montre l'interet de la notion de masse lineaire comme critere de qualite d'une fabrication. Les performances et le bilan des deux premieres campagnes de production sont enfin examines. (auteur)

  12. Different techniques in fabrication of ocular prosthesis. (United States)

    Cevik, Pinar; Dilber, Erhan; Eraslan, Oguz


    Loss of an eye caused by cancer, trauma, or congenital defect creates a deep psychological impact on an individual's life especially social and professional life. Custom-made prosthesis, compared to stock prosthesis, provides a better fit to the eye socket, better cosmetic results, and less discomfort to the patient in the long term. The main objective of this article was to describe 3 different alternative and practical techniques of fabricating custom-made ocular prosthesis. An impression of anophthalmic socket was made with the addition of cured silicone-based precision impression material in all techniques. A master cast was prepared and duplicated with condensation silicone. A self-cure acrylic resin was polymerized in the silicone model and was fitted into the patient's eye socket. A digital photograph of the patient's iris was made using a digital camera and printed on good-quality photo paper in various shades and sizes in the first and the second techniques. Then the photo paper was coated with PVC so as not to allow any color flowing. The proper iris was then inserted to the acrylic base. The prosthesis was final processed using orthodontic heat polymerizing clear acrylic resin.In the other technique, after the trying-in process with wax pattern, an acrylic base was fabricated using heat polymerizing scleral acrylic resin. The prosthetic iris was fabricated from a transparent contact lens by painting the lens with watercolor paints and attaching it to an acrylic resin with tissue conditioner. The final process was made with heat polymerizing transparent acrylic resin. Custom-made prosthesis allows better esthetic and functional results to the patient in comparison to stock prosthesis. Further follow-up is necessary to check the condition and fit of the ocular prosthesis in such patients.

  13. Maintenance and fabrication of electronic equipment

    Energy Technology Data Exchange (ETDEWEB)

    Chung, Chong Soo; Moon, Byung Soo; Hong, Suk Boong; Kim, Yong Keun; Kim, Jung Bok


    Providing technical support to the maintenance and repair problems of electronic instruments, we have assisted the research and development work, and reduced operation cost of the pilot plants in KAERI. In addition, we have improved the performance of the data processing system of RMS, and modified the cyclic box and IND100 using PLCs which are a facility for airborne monitoring in radiation area and lamp control modules of radiation monitoring control panel respectively. And also, a gamma-ray densitometer for KNGR has been designed and fabricated.

  14. Fabrication of transparent ceramics using nanoparticles (United States)

    Cherepy, Nerine J; Tillotson, Thomas M; Kuntz, Joshua D; Payne, Stephen A


    A method of fabrication of a transparent ceramic using nanoparticles synthesized via organic acid complexation-combustion includes providing metal salts, dissolving said metal salts to produce an aqueous salt solution, adding an organic chelating agent to produce a complexed-metal sol, heating said complexed-metal sol to produce a gel, drying said gel to produce a powder, combusting said powder to produce nano-particles, calcining said nano-particles to produce oxide nano-particles, forming said oxide nano-particles into a green body, and sintering said green body to produce the transparent ceramic.

  15. Fabrication and testing of composite ring specimens (United States)

    Liber, T.; Daniel, I. M.; Labedz, R.; Niiro, T.


    The tooling and techniques used in the fabrication of composite laminate tubes of any desired ply orientation and stacking sequence are described along with techniques for cutting ring specimens under internal pressure. The method consists of laying up the tube on a central circular mandrel, and by means of internal pressure, expanding the prepreg tube against the cavity wall of an external mold tool, which forms the geometric curing envelope for the tube. Tube quality is assessed by laminate wall thickness measurement, by hoop strength measurement on rings cut from the ends of the tube, and by ultrasonic inspection.

  16. Nanowires and nanostructures fabrication using template methods

    DEFF Research Database (Denmark)

    Mátéfi-Tempfli, Stefan; Mátéfi-Tempfli, M.; Vlad, A.


    One of the great challenges of today is to find reliable techniques for the fabrication of nanomaterials and nanostructures. Methods based on template synthesis and on self organization are the most promising due to their easiness and low cost. This paper focuses on the electrochemical synthesis ...... of nanowires and nanostructures using nanoporous host materials such as supported anodic aluminum considering it as a key template for nanowires based devices. New ways are opened for applications by combining such template synthesis methods with nanolithographic techniques....

  17. Fabrication of a custom ocular prosthesis. (United States)

    Sethi, Tania; Kheur, Mohit; Haylock, Colin; Harianawala, Husain


    Defects of the eye may follow removal of a part of or the entire orbit. This results in the patient becoming visually, esthetically and psychologically handicapped. Restoring the defect with a silicone- or acrylic-based prosthesis not only restores esthetics but also gives back the lost confidence to the patient. This is a case report of a patient with a 'pthisical eye' and details the steps in fabrication of an ocular prosthesis. Particular attention has been given to the laboratory process in this technique to minimize the residual monomer content in the artificial eye.

  18. Fabrication of a Microneedle Using Human Hair (United States)

    Yoshida, Yoshikazu; Takei, Tamotsu


    In this study, we developed a novel microneedle design to inject medication into the skin and to remove blood from a blood vessel. A drilling machine and chemicals were used to drill a hollow needle bore into the center of a strand of human hair. Our results demonstrate that a pen-shaped microneedle has been fabricated at a length of 1.1 mm, a base diameter of 80 µm, and a tip diameter of 40 µm. The hair microneedle was sufficiently strong to insert into the meat of a chicken leg.

  19. Carbohydrate microarrays: survey of fabrication techniques. (United States)

    Culf, Adrian S; Cuperlovic-Culf, Miroslava; Ouellette, Rodney J


    Carbohydrate microarrays are being developed in order to decipher the information content of the glycome. This postgenomic activity is necessary because of the complexity of protein biosynthesis and post-translational modifications that cannot currently be detected at the genome level. This review looks, in detail, at the experimental approaches that have been taken in the fabrication and preparation of carbohydrate microarrays, glycan arrays and glyco-chips. Tether structures, glycan solution preparation, detection methods and applications have been gathered together in a tabular format.

  20. Method of fabricating bifacial tandem solar cells (United States)

    Wojtczuk, Steven J; Chiu, Philip T; Zhang, Xuebing; Gagnon, Edward; Timmons, Michael


    A method of fabricating on a semiconductor substrate bifacial tandem solar cells with semiconductor subcells having a lower bandgap than the substrate bandgap on one side of the substrate and with subcells having a higher bandgap than the substrate on the other including, first, growing a lower bandgap subcell on one substrate side that uses only the same periodic table group V material in the dislocation-reducing grading layers and bottom subcells as is present in the substrate and after the initial growth is complete and then flipping the substrate and growing the higher bandgap subcells on the opposite substrate side which can be of different group V material.

  1. Fabrication and calibration of search coils

    CERN Document Server

    Buzio, M


    In this paper the techniques available to make and calibrate magnetic search coils are reviewed, with emphasis on harmonic coil systems as the commonly-used optimal choice for integral measurements of accelerator magnets in terms of measuring range, accuracy, and cost. The topics treated, drawing extensively on half a century of experience at CERN, include mechanical and electrical design criteria, practical fabrication techniques, metrological considerations, and various calibration methods for coil parameters such as surface area, rotation radius, tilt angle etc. in both static or time-varying magnetic fields.

  2. CCD research. [design, fabrication, and applications (United States)

    Gassaway, J. D.


    The fundamental problems encountered in designing, fabricating, and applying CCD's are reviewed. Investigations are described and results and conclusions are given for the following: (1) the development of design analyses employing computer aided techniques and their application to the design of a grapped structure; (2) the role of CCD's in applications to electronic functions, in particular, signal processing; (3) extending the CCD to silicon films on sapphire (SOS); and (4) all aluminum transfer structure with low noise input-output circuits. Related work on CCD imaging devices is summarized.

  3. In situ fabrication of a tunable microlens. (United States)

    Zhang, Lei; Wang, Zhiyuan; Wang, Yichuan; Qiu, Rui; Fang, Wei; Tong, Limin


    We demonstrate an optofluidic variable-focus microlens formed by a solid polydimethylsiloxane (PDMS) meniscus channel wall and a tunable liquid lens body. A novel method for in situ fabrication of the meniscus channel wall is developed by introducing liquid PDMS prepolymer into a microchannel followed by curing. Three-light manipulation techniques including tunable optical focusing, collimating, and diverging are realized by varying the refractive index (RI) of liquid lens body. Also, we present an absorption measurement of methylene blue (MB) with a collimated probing light, achieving a detection limit of 0.25 μM by using a 5-mm-long detection cell.

  4. Iodine Beam Dump Design and Fabrication (United States)

    Polzin, K. A.; Bradley, D. E.


    During the testing of electric thrusters, high-energy ions impacting the walls of a vacuum chamber can cause corrosion and/or sputtering of the wall materials, which can damage the chamber walls. The sputtering can also introduce the constituent materials of the chamber walls into an experiment, with those materials potentially migrating back to the test article and coating it with contaminants over time. The typical method employed in this situation is to install a beam dump fabricated from materials that have a lower sputter yield, thus reducing the amount of foreign material that could migrate towards the test article or deposit on anything else present in the vacuum facility.

  5. Particle Lithography Enables Fabrication of Multicomponent Nanostructures (United States)

    Lin, Wei-feng; Swartz, Logan A.; Li, Jie-Ren; Liu, Yang; Liu, Gang-yu


    Multicomponent nanostructures with individual geometries have attracted much attention because of their potential to carry out multiple functions synergistically. The current work reports a simple method using particle lithography to fabricate multicomponent nanostructures of metals, proteins, and organosiloxane molecules, each with its own geometry. Particle lithography is well-known for its capability to produce arrays of triangular-shaped nanostructures with novel optical properties. This paper extends the capability of particle lithography by combining a particle template in conjunction with surface chemistry to produce multicomponent nanostructures. The advantages and limitations of this approach will also be addressed. PMID:24707328

  6. Thin-Film Photovoltaic Device Fabrication (United States)

    Scofield, John H.


    This project will primarily involve the fabrication and characterization of thin films and devices for photovoltaic applications. The materials involved include Il-VI materials such as zinc oxide, cadmium sulfide, and doped analogs. The equipment ot be used will be sputtering and physical evaporations. The types of characterization includes electrical, XRD, SEM and CV and related measurements to establish the efficiency of the devices. The faculty fellow will be involved in a research team composed of NASA and University researchers as well as students and other junior researchers.

  7. Anchored nanostructure materials and method of fabrication (United States)

    Seals, Roland D; Menchhofer, Paul A; Howe, Jane Y; Wang, Wei


    Anchored nanostructure materials and methods for their fabrication are described. The anchored nanostructure materials may utilize nano-catalysts that include powder-based or solid-based support materials. The support material may comprise metal, such as NiAl, ceramic, a cermet, or silicon or other metalloid. Typically, nanoparticles are disposed adjacent a surface of the support material. Nanostructures may be formed as anchored to nanoparticles that are adjacent the surface of the support material by heating the nano-catalysts and then exposing the nano-catalysts to an organic vapor. The nanostructures are typically single wall or multi-wall carbon nanotubes.

  8. Fabrics Protect Sensitive Skin from UV Rays (United States)


    Late Johnson Space Center engineer Dr. Robert Dotts headed a team to develop cool suits for children suffering from life-threatening sun sensitivities. Dotts hoped to develop ultraviolet-blocking technology in a fabric that -- unlike in a bulky space suit -- could remain comfortable, light, and breathable in the sun and heat. The team worked with SPF 4 US LLC (SPF) of Madison, Wisconsin to design ultraviolet-blocking cool suits, which protect sun-sensitive patients and enable them to experience life outdoors safely. Using knowledge gained during the NASA collaboration, SPF created an entire line of ultraviolet-blocking apparel.

  9. Design, fabrication and control of soft robots. (United States)

    Rus, Daniela; Tolley, Michael T


    Conventionally, engineers have employed rigid materials to fabricate precise, predictable robotic systems, which are easily modelled as rigid members connected at discrete joints. Natural systems, however, often match or exceed the performance of robotic systems with deformable bodies. Cephalopods, for example, achieve amazing feats of manipulation and locomotion without a skeleton; even vertebrates such as humans achieve dynamic gaits by storing elastic energy in their compliant bones and soft tissues. Inspired by nature, engineers have begun to explore the design and control of soft-bodied robots composed of compliant materials. This Review discusses recent developments in the emerging field of soft robotics.

  10. Fabrication of implanted $^{22}$Na targets

    CERN Multimedia


    A knowledge of the $^{22}$Na(p,$\\gamma$)$^{23}$ Mg reaction rate is of significant astrophysical interest. In order to complete previous studies of this reaction, radioactive $^{22}$Na targets of high purity are required. We ask for support to fabricate these targets via the implantation technique at ISOLDE GPS (off—line mode) using $^{22}$Na nuclides in an Al matrix produced in Nov. 1990 at the PSI (Zürich). The $^{22}$Na nuclides are released and ionized in a surface ionisation source, mass-analyzed at ISOLDE GPS, and implanted in a Ni-Ta backing and a C—foil in a special implantation setup.

  11. 2k micro moulding for MID fabrication

    DEFF Research Database (Denmark)

    Islam, Aminul; Hansen, Hans Nørgaard; Jørgensen, Martin Bondo


    Molded Interconnect Devices (MIDs) are plastic substrates with electrical infrastructure. The fabrication of MIDs is usually based on injection molding and different process chains may be identified from this starting point. The use of MIDs has been driven primarily by the automotive sector......, but recently the medical sector seems more and more interested. In particular, the possibility of miniaturization of 3D components with electrical infrastructure is attractive. The paper describes possible manufacturing routes and challenges of miniaturized MIDs based on two component injection molding...... modulate the qualities of final MID. Results and discussion presented here can be a valuable used guide for mass production of molded interconnect devices....

  12. Dream, Joke, and Social Fabric: On Writing

    Directory of Open Access Journals (Sweden)

    Hilda Teresita Karlen Zbrun


    Full Text Available Through the narration of a dream, the article seeks to account for the fact that the formations of the unconscious are possible whenever subjects are involved in the social fabric. Just as a joke is a joke because there is someone to laugh at it, a dream, when it is narrated, becomes a text to be read. Subjects resort to these formations when they feel trapped due to an approximation to the real. Although the real appears as a boundary that halts writing, it is also the condition of possibility of subjective production.

  13. Modelling the Effect of Weave Structure and Fabric Thread Density on Mechanical and Comfort Properties of Woven Fabrics

    Directory of Open Access Journals (Sweden)

    Maqsood Muhammad


    Full Text Available The paper investigates the effects of weave structure and fabric thread density on the comfort and mechanical properties of various test fabrics woven from polyester/cotton yarns. Three different weave structures, that is, 1/1 plain, 2/1 twill and 3/1 twill, and three different fabric densities were taken as input variables whereas air permeability, overall moisture management capacity, tensile strength and tear strength of fabrics were taken as response variables and a comparison is made of the effect of weave structure and fabric density on the response variables. The results of fabric samples were analysed in Minitab statistical software. The coefficients of determinations (R-sq values of the regression equations show a good predictive ability of the developed statistical models. The findings of the study may be helpful in deciding appropriate manufacturing specifications of woven fabrics to attain specific comfort and mechanical properties.

  14. Antibacterial property of fabrics coated by magnesium-based brucites

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Ying; Sha, Lin; Zhao, Jiao; Li, Qian; Zhu, Yimin, E-mail:; Wang, Ninghui


    Highlights: • Magnesium-based antibacterial agents composited by brucites with different particle sizes were proposed for the first time. • The coating process for making antibacterial fabrics was easy to operate and apply in industrial application. • The materials used in the antibacterial fabrics were environmental-friendly and cost-effective. • Reduction percentage of as-prepared antibacterial fabrics against E. coli and S. aureus reached to 96.6%, 100% respectively. • The antibacterial fabrics attained excellent washing durability. - Abstract: A kind of environmental-friendly magnesium-based antibacterial agent was reported for the first time, which was composited by brucites with different particle sizes. The antibacterial fabrics were produced by coating the magnesium-based antibacterial agents on the 260T polyester pongee fabrics with waterborne polyurethane. The coating process was simple, low-cost, and harmless to human health and environment. Characteristics of the antibacterial agents and fabrics were studied by particulate size distribution analyzer (PSDA), X-ray diffraction (XRD), and scanning electron microscopy (SEM). The results demonstrated that the coating layer was covered tightly on the fabrics and compositing of different particles by a certain proportion made full filling of the coating layer. Meanwhile, compositing did not change the structure of brucites. The antibacterial fabrics presented strong antibacterial properties against Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus), with the reduction percentage of 96.6% and 100%, respectively, and the antibacterial fabrics attained excellent washing durability.

  15. Smart fabric sensors and e-textile technologies: a review (United States)

    Castano, Lina M.; Flatau, Alison B.


    This paper provides a review of recent developments in the rapidly changing and advancing field of smart fabric sensor and electronic textile technologies. It summarizes the basic principles and approaches employed when building fabric sensors as well as the most commonly used materials and techniques used in electronic textiles. This paper shows that sensing functionality can be created by intrinsic and extrinsic modifications to textile substrates depending on the level of integration into the fabric platform. The current work demonstrates that fabric sensors can be tailored to measure force, pressure, chemicals, humidity and temperature variations. Materials, connectors, fabric circuits, interconnects, encapsulation and fabrication methods associated with fabric technologies prove to be customizable and versatile but less robust than their conventional electronics counterparts. The findings of this survey suggest that a complete smart fabric system is possible through the integration of the different types of textile based functional elements. This work intends to be a starting point for standardization of smart fabric sensing techniques and e-textile fabrication methods.

  16. Interpreting the formation of bloodstains on selected apparel fabrics. (United States)

    de Castro, Therese; Nickson, Tania; Carr, Debra; Knock, Clare


    Bloodstain pattern analysis (BPA) is the investigation and interpretation of blood deposited at crime scenes. However, the interaction of blood and apparel fabrics has not been widely studied. In this work, the development of bloodstains (passive, absorbed and transferred) dropped from three different heights (500, 1,000, 1,500 mm) on two cotton apparel fabrics (1 × 1 rib knit, drill) was investigated. High-speed video was used to investigate the interaction of the blood and fabric at impact. The effect of drop height on the development of passive, absorbed and transferred bloodstains was investigated using image analysis and statistical tools. Visually, the passive bloodstain patterns produced on the technical face of fabrics from the different drop heights were similar. The blood soaked unequally through to the technical rear of both fabrics. Very little blood was transferred between a bloody fabric and a second piece of fabric. Statistically, drop height did not affect the size of the parent bloodstain (wet or dry), but did affect the number of satellite bloodstains formed. Some differences between the two fabrics were noted, therefore fabric structure and properties must be considered when conducting BPA on apparel fabrics.

  17. Fabricating an S&OP Process

    DEFF Research Database (Denmark)

    Lichen, Alex Yu

    Inspired by Latour’s (2005a) notion of matters of concern and M.C. Escher’s Circle Limit III as a representation of the Poincaré Disk, this study follows how an S&OP process was fabricated in a large Swedish manufacturing company. The study claims that when actors are fabricating the S&OP process......, local actors create emergent, ongoing and multiple matters of concern around it. The group demand chain, the actor who is responsible for guiding the implementation of the process, delegates the attempts to close these matters of concern to local actors located in separate times and spaces. As a result......, constituents of the S&OP process are dispersed in diverse local times and spaces rather than being coordinated in a single time and space by the group demand chain. Accounting is a set of matters of concern. The S&OP process and its purpose of integration come from an “absolute nothingness” – its minimal...

  18. Design and fabrication of a hybrid actuator (United States)

    Fu, Yao; Ghantasala, Muralidhar K.; Harvey, Erol; Qin, Lijiang


    The necessity to reduce the size of actuators and at the same time increase the force and the air gap has placed severe constraints on the suitability of current microactuator technology for various applications. This has led to the development of new actuator technologies based on novel materials or modifying existing systems. As an effort in this direction, we are reporting on the design and fabrication of a hybrid actuator employing a combination of electromagnetic and piezoelectric actuation methods for the first time. This actuator was designed and optimized by using the piezoelectric and electromagnetic solvers of commercially available FEM software packages (CoventorWare and ANSYS). The device consists of a shaped piezoelectric composite cantilever on the top and a copper coil wound around a permalloy core assembled on a silicon substrate with a permanent magnet at the bottom. The composite cantilever consists of polarized piezoelectric polymer polyvinylidene fluoride (PVDF) with an electroplated permalloy layer on one side. Microstructures in the required shape are introduced using novel methodologies including laser micromachining and microembossing. The hybrid actuator has been fabricated and tested using standard testing procedures. The experimental data are compared with the simulation results from both the finite element methods and the analytical model. There is excellent agreement between the results obtained in simulation and by experiment. A maximum total deflection of 400 µm with a typical contact force of 200 µN has been achieved.

  19. Research highlights: microfluidically-fabricated materials. (United States)

    Koh, Jaekyung; Wu, Chueh-Yu; Kittur, Harsha; Di Carlo, Dino


    Polymer particles with precise shapes or chemistries are finding unique uses in a variety of applications, including tissue engineering, drug delivery, barcoding, and diagnostic imaging. Microfluidic systems have been and are continuing to play a large role in enabling the precision synthesis of designer particles in a uniform manner. To expand the impact of these microfluidic-fabricated materials additional fundamental capabilities should still be developed. The capability to fabricate microparticles with complex three-dimensional shapes and increase the production rate of particles to an industrial scale will allow evaluation of shaped particles in a range of new applications to enhance biological, magnetic, optical, surface wetting, as well as other interfacial or mechanical properties of materials. Here we highlight work applying large collections of simple spherical microgels, with unique surface chemistry that allows in situ particle-particle annealing, to form microporous injectable scaffolds for accelerated tissue regeneration. We also report on two other techniques that are addressing the ability to create 3D-shaped microparticles by first sculpting a fluid precursor stream, and increasing the rate of production of particles using contact lithography to millions of particles per hour. The combination of these capabilities and the applications they will enable suggest a bright future for microfluidics in making the next materials.

  20. Fabrication of taste sensor for education (United States)

    Wu, Xiao; Tahara, Yusuke; Toko, Kiyoshi; Kuriyaki, Hisao


    In order to solve the unconcern to usefulness of learning science among high school students in Japan, we developed a simple fabricated taste sensor with sensitivity and selectivity to each taste quality, which can be applied in science class. A commercialized Teflon membrane was used as the polymer membrane holding lipids. In addition, a non-adhesive method is considered to combine the membrane and the sensor electrode using a plastic cap which is easily accessible. The taste sensor for education fabricated in this way showed a good selectivity and sensitivity. By adjusting the composition of trioctylmethylammonium chloride (TOMA) and phosphoric acid di(2-ethylhexyl) ester (PAEE) included in lipid solution, we improved the selectivity of this simple taste sensor to saltiness and sourness. To verify this taste sensor as a useful science teaching material for science class, we applied this taste sensor into a science class for university students. By comparing the results between the sensory test and the sensor response, humans taste showed the same tendency just as the sensor response, which proved the sensor as a useful teaching material for science class.

  1. Earth's oldest mantle fabrics indicate Eoarchaean subduction. (United States)

    Kaczmarek, Mary-Alix; Reddy, Steven M; Nutman, Allen P; Friend, Clark R L; Bennett, Vickie C


    The extension of subduction processes into the Eoarchaean era (4.0-3.6 Ga) is controversial. The oldest reported terrestrial olivine, from two dunite lenses within the ∼3,720 Ma Isua supracrustal belt in Greenland, record a shape-preferred orientation of olivine crystals defining a weak foliation and a well-defined lattice-preferred orientation (LPO). [001] parallel to the maximum finite elongation direction and (010) perpendicular to the foliation plane define a B-type LPO. In the modern Earth such fabrics are associated with deformation of mantle rocks in the hanging wall of subduction systems; an interpretation supported by experiments. Here we show that the presence of B-type fabrics in the studied Isua dunites is consistent with a mantle origin and a supra-subduction mantle wedge setting, the latter supported by compositional data from nearby mafic rocks. Our results provide independent microstructural data consistent with the operation of Eoarchaean subduction and indicate that microstructural analyses of ancient ultramafic rocks provide a valuable record of Archaean geodynamics.

  2. Design and Fabrication of an Anaerobic Digester

    Directory of Open Access Journals (Sweden)

    M. S. Abubakar


    Full Text Available Anaerobic digester is a physical structure that provides a conducive environment for the multiplication of micro-organisms that degrades organic matter to generate biogas energy. Energy is required in agriculture for crop production, processing and storage, poultry production and electricity for farmstead and farm settlements. It is energy that propels agricultural mechanization, which minimizes the use of human and animal muscles and its inherent drudgery in agriculture. The energy demand required to meet up with the agricultural growth in Nigeria is high and growing every year. In this study the design and fabrication of an anaerobic digester was reported which is an attempt to boost energy requirement for small and medium dryland farmers in Nigeria. The design of the digester includes the following concept; the basic principles of anaerobic digestion processes, socio-economic status of the dryland farmers, amount of biogas to be produced. Finally, the digester was fabricated using locally available raw materials within the dryland area of Nigeria. At the end, preliminary flammability test was conducted and the biogas produced was found to be flammable.

  3. Proposed technique for fabricating complete denture

    Directory of Open Access Journals (Sweden)

    Abdulsalam Ali Zwiad


    Full Text Available Introduction: Reduction of the visits for fabricating complete dentures are welcomed by both dentists and patients and this might be an aspect of the new changes in prosthodontic treatment according to the suggested new methods. Clinical Innovation: Complete dentures fabricated by the technique described in this report reduce processing time, cost and efforts since the technique does not require the use of gypsum materials, metal flasks or other related materials to obtain a mold for packing the heat cured acrylic resin as might be needed with the conventional method. This method requires only an appropriate volume of silicone impression material to provide the required mold and a heat pressure machine for processing and polymerization of the heat-cured acrylic resin. Although this technique might be difficult to be applicable by all dentist but it could be consider an advisable method. Discussion: Because the record base in this technique is made of heat cured resin, it provides a reliable denture base with better retention and stability and it overcomes the shortcomings that may be faced during registration of vertical dimension. This technique meets the basic requirements for a successful complete denture which is well tolerated by the patient′s mouth.

  4. Template-assisted fabrication of protein nanocapsules (United States)

    Dougherty, Shelley A.; Liang, Jianyu; Kowalik, Timothy F.


    Bionanomaterials have recently begun to spark a great amount of interest and could potentially revolutionize biomedical research. Nanoparticles, nanocapsules, and nanotubular structures are becoming attractive options in drug and gene delivery. The size of the delivery vehicles greatly impacts cellular uptake and makes it highly desirable to precisely control the diameter and length of nanocarriers to make uniform nanoparticles at low cost. Carbon nanotubes have shown great potential within the field of drug and gene delivery. However, their insolubility and cytotoxicity could severely delay FDA approval. A desirable alternative would be to fabricate nanostructures from biomaterials such as proteins, peptides, or liposomes, which are already FDA approved. In this article we demonstrate the preparation of protein nanocapsules with both ends sealed using a template-assisted alternate immersion method combined with controlled cleaving. Glucose oxidase nanocapsules with controllable diameter, wall thickness, and length were fabricated and characterized with SEM and TEM. The biochemical activity of glucose oxidase in the form of nanocapsules after processing was confirmed using UV spectrometry. Our future work will explore proteins suitable for drug encapsulation and cellular uptake and will focus on optimizing the cleaving process to gain precise control over the length of the nanocapsules.

  5. Evolving MEMS Resonator Designs for Fabrication (United States)

    Hornby, Gregory S.; Kraus, William F.; Lohn, Jason D.


    Because of their small size and high reliability, microelectromechanical (MEMS) devices have the potential to revolution many areas of engineering. As with conventionally-sized engineering design, there is likely to be a demand for the automated design of MEMS devices. This paper describes our current status as we progress toward our ultimate goal of using an evolutionary algorithm and a generative representation to produce designs of a MEMS device and successfully demonstrate its transfer to an actual chip. To produce designs that are likely to transfer to reality, we present two ways to modify evaluation of designs. The first is to add location noise, differences between the actual dimensions of the design and the design blueprint, which is a technique we have used for our work in evolving antennas and robots. The second method is to add prestress to model the warping that occurs during the extreme heat of fabrication. In future we expect to fabricate and test some MEMS resonators that are evolved in this way.

  6. SPS Fabric of the Cosmos Cafe (United States)

    Chakrabarti, Anish


    Hosted by Brian Greene and based on his best-selling book of the same title, The Fabric of the Cosmos is a new four- part NOVA series that explores the deepest mysteries of space and time. The program was kicked-off by 30 ``Cosmic Cafes'' being held around the country funded by an NSF grant which allows SPS-NOVA to fund SPS chapters for these events. During the summer I assisted in planning this kick-off, reviewing and suggesting revisions of resources related to the NOVA series to make them relevant to an SPS audience. I also got to organize and moderate the first ``Cosmic Cafe.'' The Cosmic cafe that I organized was discussion based, with our speaker Dr. James Gates starting with a short talk and then opening the floor up for questions. By organizing a ``Cosmic cafe,'' I got real hand experience about the challenges an SPS chapter would face while organizing a cafe themselves. Based on my experience I shall also discuss the effectiveness of the first ever themed science cafe blitz. A science caf'e is an informal discussion with an expert in a very casual location, usually a restaurant, coffee shop, or a bar. A science cafe is mostly discussion based, but has a lot of freedom for the format. A ``Cosmic'' cafe is a science cafe which is based around the topics discussed in the documentary ``The Fabric of the Cosmos.''

  7. LIFE Target Fabrication Research Plan Sept 2008

    Energy Technology Data Exchange (ETDEWEB)

    Miles, R; Biener, J; Kucheyev, S; Montesanti, R; Satcher, J; Spadaccini, C; Rose, K; Wang, M; Hamza, A; Alexander, N; Brown, L; Hund, J; Petzoldt, R; Sweet, W; Goodin, D


    The target-system for the baseline LIFE fast-ignition target was analyzed to establish a preliminary estimate for the costs and complexities involved in demonstrating the technologies needed to build a prototype LIFE plant. The baseline fast-ignition target upon which this analysis was developed is shown in Figure 1.0-1 below. The LIFE target-system incorporates requirements for low-cost, high throughput manufacture, high-speed, high accuracy injection of the target into the chamber, production of sufficient energy from implosion and recovery and recycle of the imploded target material residue. None of these functions has been demonstrated to date. Existing target fabrication techniques which lead to current 'hot spot' target costs of {approx}$100,000 per target and at a production rate of 2/day are unacceptable for the LIFE program. Fabrication techniques normally used for low-cost, low accuracy consumer products such as toys must be adapted to the high-accuracy LIFE target. This will be challenge. A research program resulting is the demonstration of the target-cycle technologies needed for a prototype LIFE reactor is expected to cost {approx}$51M over the course of 5 years. The effort will result in targets which will cost an estimated $0.23/target at a rep-rate of 20 Hz or about 1.73M targets/day.

  8. Method for fabricating a microelectromechanical resonator

    Energy Technology Data Exchange (ETDEWEB)

    Wojciechowski, Kenneth E; Olsson, III, Roy H


    A method is disclosed which calculates dimensions for a MEM resonator in terms of integer multiples of a grid width G for reticles used to fabricate the resonator, including an actual sub-width L.sub.a=NG and an effective electrode width W.sub.e=MG where N and M are integers which minimize a frequency error f.sub.e=f.sub.d-f.sub.a between a desired resonant frequency f.sub.d and an actual resonant frequency f.sub.a. The method can also be used to calculate an overall width W.sub.o for the MEM resonator, and an effective electrode length L.sub.e which provides a desired motional impedance for the MEM resonator. The MEM resonator can then be fabricated using these values for L.sub.a, W.sub.e, W.sub.o and L.sub.e. The method can also be applied to a number j of MEM resonators formed on a common substrate.

  9. A scalable fabrication process of polymer microneedles. (United States)

    Yang, Sixing; Feng, Yan; Zhang, Lijun; Chen, Nixiang; Yuan, Weien; Jin, Tuo


    While polymer microneedles may easily be fabricated by casting a solution in a mold, either centrifugation or vacuumizing is needed to pull the viscous polymer solution into the microholes of the mold. We report a novel process to fabricate polymer microneedles with a one-sided vacuum using a ceramic mold that is breathable but water impermeable. A polymer solution containing polyvinyl alcohol and polysaccharide was cast in a ceramic mold and then pulled into the microholes by a vacuum applied to the opposite side of the mold. After cross-linking and solidification through freeze-thawing, the microneedle patch was detached from the mold and transferred with a specially designed instrument for the drying process, during which the patch shrank evenly to form an array of regular and uniform needles without deformation. Moreover, the shrinkage of the patches helped to reduce the needles' size to ease microfabrication of the male mold. The dried microneedle patches were finally punched to the desired sizes to achieve various properties, including sufficient strength to penetrate skin, microneedles-absorbed water-swelling ratios, and drug-release kinetics. The results showed that the microneedles were strong enough to penetrate pigskin and that their performance was satisfactory in terms of swelling and drug release.

  10. Fabricating PFPE Membranes for Capillary Electrophoresis (United States)

    Lee, Michael C.; Willis, Peter A.; Greer, Frank; Rolland, Jason


    A process has been developed for fabricating perfluoropolyether (PFPE) membranes that contain microscopic holes of precise sizes at precise locations. The membranes are to be incorporated into laboratory-on-a-chip microfluidic devices to be used in performing capillary electrophoresis. The present process is a modified version of part of the process, described in the immediately preceding article, that includes a step in which a liquid PFPE layer is cured into solid (membrane) form by use of ultraviolet light. In the present process, one exploits the fact that by masking some locations to prevent exposure to ultraviolet light, one can prevent curing of the PFPE in those locations. The uncured PFPE can be washed away from those locations in the subsequent release and cleaning steps. Thus, holes are formed in the membrane in those locations. The most straightforward way to implement the modification is to use, during the ultraviolet-curing step, an ultraviolet photomask similar to the photomasks used in fabricating microelectronic devices. In lieu of such a photomask, one could use a mask made of any patternable ultraviolet-absorbing material (for example, an ink or a photoresist).

  11. Fabrication of ZnO incorporated chitosan nanocomposites for enhanced functional properties of cellulosic fabric (United States)

    Raza, Z. A.; Anwar, F.; Ahmad, S.; Aslam, M.


    This study concerns the fabrication of chitosan/zinc oxide nano-composites (CZNCs) by using a facile preparation method. The optical, structural and morphological features of nano-composites were investigated by using advanced analytical techniques. The developed CZNCs were coated on to woven cotton fabric by using the pad-dry-cure method. The coated fabric specimens were characterized for surface, functional and textile properties including antibacterial activity and (ultra violet) UV-blocking. The spectral and optical properties demonstrated that the nano-composites developed exhibited hexagonal structural pattern with an average particle size of about 50 nm. The resulting nano-composites were characterized by x-ray diffraction spectroscopy; scanning electron microscopy equipped with energy dispersive x-ray, dynamic light scattering technique and so forth. The incorporated concentration of zinc oxide nanoparticles affected both crystallite size and crystallinity of the nano-composites. The nano-composite coated cotton fabric exhibited durable antibacterial, UV-blocking and textile properties with a fair whiteness index.

  12. Fabrication of microchannels in polycrystalline diamond using pre-fabricated Si substrates (United States)

    Chandran, Maneesh; Elfimchev, Sergey; Michaelson, Shaul; Akhvlediani, Rozalia; Ternyak, Orna; Hoffman, Alon


    In this paper, we report on a simple, feasible method to fabricate microchannels in diamond. Polycrystalline diamond microchannels were produced by fabricating trenches in a Si wafer and subsequently depositing a thin layer of diamond onto this substrate using the hot filament vapor deposition technique. Fabrication of trenches in the Si substrate at different depths was carried out by standard photolithography, and the subsequent deposition of the diamond layer was performed by the hot filament chemical vapor deposition technique. The growth mechanism of diamond that leads to the formation of closed diamond microchannels is discussed in detail based on the Knudsen number and growth chemistry of diamond. Variations in the crystallite size, crystalline quality, and thickness of the diamond layer along the trench depths were systematically analyzed using cross-sectional scanning electron microscopy and Raman spectroscopy. Defect density and formation of non-diamond forms of carbon in the diamond layer were found to increase with the trench depth, which sets a limit of 5-45 μm trench depth (or an aspect ratio of 1-9) for the fabrication of diamond microchannels using this method under the present conditions.

  13. Functionalisation of fabrics with conducting polymer for tuning capacitance and fabrication of supercapacitor. (United States)

    Firoz Babu, K; Siva Subramanian, S P; Anbu Kulandainathan, M


    Conducting polymer (polypyrrole (PPy) doped with anion) film has been coated on different textile substrates from a mild, room temperature wet in situ chemical polymerisation method exploiting pyrrole as a monomer and ferric chloride as an oxidant and compared their electrochemical capacitive behaviour by assembling as an unit cell supercapacitor. PPy composites were prepared with carbohydrate polymers like cotton, linen (Natural cellulosic fibre), modified cellulosic fibre-viscose rayon and synthetic polymer polyester fabrics to investigate the influence on electrochemical capacitance. The surface morphology and chemistry of these materials were analysed by SEM, FT-IR, and XRD. It reveals that the PPy has greater interaction with the cellulosic fabrics, but whereas surface deposition only has taken place with synthetic fibres. The capacitive behaviour of the PPy coated textiles were evaluated using cyclic voltammetry, impedance spectroscopy and charge-discharge analysis. A unit cell was fabricated to investigate the capacitive behaviour by assembling two symmetric textile electrodes separated by a solid polymer (PVA/1M H2SO4 gel) electrolyte membrane. The textile electrodes prepared with PPy-Cotton and PPy-Viscose exhibited the highest specific capacitance value of 268 F g(-1) and 244 F g(-1), respectively at a scan rate of 5 mV s(-1). The charge-discharge analysis also shows higher specific capacitance value for PPy-Viscose and PPy-Cotton. The focus of this research is to highlight a successful, simple and reproducible method for fabrication of the textile based supercapacitor and the chemistry of surface interaction of PPy molecule with natural and synthetic fabrics. Copyright © 2013 Elsevier Ltd. All rights reserved.

  14. Redundancy of Supply in the International Nuclear Fuel Fabrication Market: Are Fabrication Services Assured?

    Energy Technology Data Exchange (ETDEWEB)

    Seward, Amy M.; Toomey, Christopher; Ford, Benjamin E.; Wood, Thomas W.; Perkins, Casey J.


    For several years, Pacific Northwest National Laboratory (PNNL) has been assessing the reliability of nuclear fuel supply in support of the U.S. Department of Energy/National Nuclear Security Administration. Three international low enriched uranium reserves, which are intended back up the existing and well-functioning nuclear fuel market, are currently moving toward implementation. These backup reserves are intended to provide countries credible assurance that of the uninterrupted supply of nuclear fuel to operate their nuclear power reactors in the event that their primary fuel supply is disrupted, whether for political or other reasons. The efficacy of these backup reserves, however, may be constrained without redundant fabrication services. This report presents the findings of a recent PNNL study that simulated outages of varying durations at specific nuclear fuel fabrication plants. The modeling specifically enabled prediction and visualization of the reactors affected and the degree of fuel delivery delay. The results thus provide insight on the extent of vulnerability to nuclear fuel supply disruption at the level of individual fabrication plants, reactors, and countries. The simulation studies demonstrate that, when a reasonable set of qualification criteria are applied, existing fabrication plants are technically qualified to provide backup fabrication services to the majority of the world's power reactors. The report concludes with an assessment of the redundancy of fuel supply in the nuclear fuel market, and a description of potential extra-market mechanisms to enhance the security of fuel supply in cases where it may be warranted. This report is an assessment of the ability of the existing market to respond to supply disruptions that occur for technical reasons. A forthcoming report will address political disruption scenarios.

  15. Disc resonator gyroscope fabrication process requiring no bonding alignment (United States)

    Shcheglov, Kirill V. (Inventor)


    A method of fabricating a resonant vibratory sensor, such as a disc resonator gyro. A silicon baseplate wafer for a disc resonator gyro is provided with one or more locating marks. The disc resonator gyro is fabricated by bonding a blank resonator wafer, such as an SOI wafer, to the fabricated baseplate, and fabricating the resonator structure according to a pattern based at least in part upon the location of the at least one locating mark of the fabricated baseplate. MEMS-based processing is used for the fabrication processing. In some embodiments, the locating mark is visualized using optical and/or infrared viewing methods. A disc resonator gyroscope manufactured according to these methods is described.

  16. Local electrophoretic deposition using a nanopipette for micropillar fabrication (United States)

    Iwata, Futoshi; Metoki, Junya


    A novel and simple technique was developed for the fabrication of micropillars using a nanopipette that is a tapered glass capillary with a micrometer-sized aperture at the tip. The nanopipette was filled with a colloidal solution that included metal nanoparticles. Its tip was put in contact with a substrate, and the substrate was moved downward for continuous deposition of the metal colloidal solution to form micropillars. To improve fabrication reproducibility, the amount of Au colloidal solution deposited was controlled by a feedback loop that maintained a predefined constant current during electrophoretic deposition. The stiffness of the fabricated micropillars was evaluated by applying a loading force using a microcantilever under scanning electron microscopy. The Young’s modulus of the fabricated pillars was measured to be in the range of 7.7–14.8 GPa, depending on the fabrication parameters of the predefined current and fabrication speed.

  17. Integration of textile fabric and coconut shell in particleboard (United States)

    Misnon, M. I.; Bahari, S. A.; Islam, M. M.; Epaarachchi, J. A.


    In this study, cotton fabric and coconut shell were integrated in particleboard to reduce the use of wood. Particleboards containing mixed rubberwood and coconut shell with an equal weight ratio have been integrated with various layers of cotton fabric. These materials were bonded by urea formaldehyde with a content level of 12% by weight. Flexural and water absorption tests were conducted to analyze its mechanical properties and dimensional stability. Results of flexural test showed an increment at least double strength values in fabricated materials as compared to control sample. The existence of fabric in the particleboard system also improved the dimensional stability of the produced material. Enhancement of at least 39% of water absorption could help the dimensional stability of the produced material. Overall, these new particleboards showed better results with the incorporation of cotton fabric layers and this study provided better understanding on mechanical and physical properties of the fabricated particleboard.

  18. Imparting permanent antimicrobial activity onto viscose and acrylic fabrics. (United States)

    Mekewi, M; El-Sayed, A Atef; Amin, M S; Said, Hala I


    Viscose and acrylic fabrics were aminated to enhance metal chelation of Cu, Zn and Ni for the purpose of imparting fabrics antimicrobial activity against Escherichia coli and Staphylococcus aureus. Fabrics were firstly epoxidized using epichlorohydrin prior amination. Optimization of the reaction conditions, e.g., temperature, medium pH, amine type and metal type and their concentrations, are reported. Aminated fabrics of viscose and acrylic were shown to be viable for chelation with divalent metal cations. The overall results revealed that antibacterial resistance of metalized aminated fabrics that the activity trend of metals is in the order Cu-complex>Zn-complex>Ni-complex with regard to fighting of microorganisms and permanent even after 10 washing. Reaction mechanism of epoxidation, amination and metal chelation of fabrics are offered supported by FT-IR structural study, nitrogen content and atomic absorption spectroscopy. Copyright © 2012 Elsevier B.V. All rights reserved.

  19. Innovative forming and fabrication technologies : new opportunities.

    Energy Technology Data Exchange (ETDEWEB)

    Davis, B.; Hryn, J.; Energy Systems; Kingston Process Metallurgy, Inc.


    The advent of light metal alloys and advanced materials (polymer, composites, etc.) have brought the possibility of achieving important energy reductions into the full life cycle of these materials, especially in transportation applications. 1 These materials have gained acceptance in the aerospace industry but use of light metal alloys needs to gain wider acceptance in other commercial transportation areas. Among the main reasons for the relatively low use of these materials are the lack of manufacturability, insufficient mechanical properties, and increased material costs due to processing inefficiencies. Considering the enormous potential energy savings associated with the use of light metal alloys and advanced materials in transportation, there is a need to identify R&D opportunities in the fields of materials fabrication and forming aimed at developing materials with high specific mechanical properties combined with energy efficient processes and good manufacturability. This report presents a literature review of the most recent developments in the areas of fabrication and metal forming focusing principally on aluminum alloys. In the first section of the document, the different sheet manufacturing technologies including direct chill (DC) casting and rolling, spray forming, spray rolling, thin slab, and strip casting are reviewed. The second section of the document presents recent research on advanced forming processes. The various forming processes reviewed are: superplastic forming, electromagnetic forming, age forming, warm forming, hydroforming, and incremental forming. Optimization of conventional forming processes is also discussed. Potentially interesting light metal alloys for high structural efficiency including aluminum-scandium, aluminum-lithium, magnesium, titanium, and amorphous metal alloys are also reviewed. This section concludes with a discussion on alloy development for manufacturability. The third section of the document reviews the latest

  20. Comfort Characterization of Various Fabrics for Extremity Protection (United States)


    Tables Table 1. Evaluated fabrics. Areal density values are manufacturer values, except for polyester and continuous fiber knitted aramid (CFKA) fabrics...continuous fiber knitted aramid (CFKA) fabrics, which were experimentally measured. Note: ACU = Army Combat Uniform. Sample Part Areal name Description...Technology Laboratory, U.K. Ministry of Defence. ArmorFelt is a commercial product composed of felted aramid and UHMWPE fibers . TexTech is a hybrid

  1. A biomimic thermal fabric with high moisture permeability


    Fan Jie; Cheng Qian; Zhao Lian-Ying; Liu Yong; Ma Chong-Qi


    Moisture comfort is an essential factor for functional property of thermal cloth, especially for thick thermal cloth, since thick cloth may hinder effective moisture permeation, and high moisture concentration in the micro-climate between skin and fabric would cause cold feeling. Here, we report a biomimic thermal fabric with excellent warm retention and moisture management properties. In this fabric, the warp yarn system constructs many tree-shaped channel...

  2. Fabrication of selective solar absorbers using pulsed laser deposition

    CSIR Research Space (South Africa)

    Yalisi, B


    Full Text Available solar absorbers have been fabricated before using different techniques, among them the sol gel technique, sputtering, painting and the chemical vapour deposition (CVD) technique....

  3. Advanced Silicone-based Coatings for Flexible Fabric Applications Project (United States)

    National Aeronautics and Space Administration — Silicone coatings are the system of choice for inflatable fabrics used in several space, military, and consumer applications, including airbags, parachutes, rafts,...

  4. Fabrication and Characterization of Edge-Emitting Semiconductor Lasers (United States)

    Song, Junyeob

    The semiconductor laser was invented in 1962, and has recently become ubiquitous in modern life. This thesis focuses on the development of a semiconductor laser fabricating process which utilizes semiconductor manufacturing technology in a cleanroom environment including photolithography, etching, deposition, and bonding processes. A photomask for patterning is designed, recipes of photolithography process and etching process are developed with experiments. This work gives how to develop the process of fabrication and determine the parameters for each processes. A series of semiconductor laser devices are then fabricated using the developed process and characterization is performed to assess device performance with industrial standard methods. A fabricated device has 18W power and 11% conversion efficiency.

  5. Preparation and characterisation of thermoresponsive nanogels for smart antibacterial fabrics

    Energy Technology Data Exchange (ETDEWEB)

    Zafar, Muhammad [Institute of Materials Research and Innovation, University of Bolton (United Kingdom); Shah, Tahir, E-mail: [Institute of Materials Research and Innovation, University of Bolton (United Kingdom); Rawal, Amit [Department of Textile Technology, Indian Institute of Technology Delhi, Hauz Khas, New Delhi (India); Siores, Elias [Institute of Materials Research and Innovation, University of Bolton (United Kingdom); TEI Athens, Agiou Spyrodonos, 12243 Egaleo, Athens (Greece)


    The present investigation involves the preparation and characterisation of silver containing nanogels and their incorporation onto the surface of woven fabrics so that they can be potentially used in biomedical applications such as wound dressings. These silver nanoparticles were mixed with N-isopropylacrylamide (NIPAM) based nanogels during and at the end of polymerisation process prior to their application onto the fabrics. NIPAM based nanogels were found to have a peak of lower critical solution temperature (LCST) that is close to the human body temperature. These nanogels were applied on cotton fabrics and cured for 15 h at 30 °C. Silver based nanogels were padded onto the fabrics followed by drying at 30 °C overnight. Scanning electron microscopy images have shown excellent distribution of silver nanoparticles on the fabric surface. EDX analysis was also conducted to confirm the presence of silver particles on the fabric surface. The results showed that a cotton fabric treated with silver based nanogels prevented the growth of bacteria, i.e. Gram-positive (Staphylococcus epidermidis) and Gram-negative (Escherichia coli), on whereas the control cotton fabric samples exhibited considerable level of bacterial growth. Specifically, the nanogels in which the silver particles were added during the polymerisation process were observed to have higher antibacterial efficacy towards both types of bacteria. - Highlights: • Silver containing NIPAM based nanogels were prepared and characterised. • Cotton fabric treated with silver based nanogels prevented the growth of bacteria. • Silver particles added during polymerisation revealed higher antibacterial efficacy.

  6. One-step fabrication of supramolecular microcapsules from microfluidic droplets

    National Research Council Canada - National Science Library

    Zhang, Jing; Coulston, Roger J; Jones, Samuel T; Geng, Jin; Scherman, Oren A; Abell, Chris


    Although many techniques exist for preparing microcapsules, it is still challenging to fabricate them in an efficient and scalable process without compromising functionality and encapsulation efficiency...

  7. Fabrication Routes for Continuous Fiber-Reinforced Ceramic Composites (CFCC) (United States)

    DiCarlo, James A.; Bansal, Narottam P.


    The primary approaches used for fabrication of continuous fiber-reinforced ceramic composite (CFCC) components have been reviewed. The CFCC fabrication issues related to fiber, interface, and matrix have been analyzed. The capabilities, advantages and limitations of the five matrix-infiltration routes have been compared and discussed. Today, the best fabrication route for the CFCC end-user is not clear and compromises need to be made depending on the details of the CFCC application. However, with time, this problem should be reduced as research continues to develop advanced CFCC constituents and fabrication routes.

  8. Fabrication Process Development for Light Deformable Mirrors Project (United States)

    National Aeronautics and Space Administration — This development is a collaborative effort between California Institute of Technology (Caltech) and the Jet Propulsion Laboratory (JPL). The fabrication is done...

  9. A Statistical Approach for Obtaining the Controlled Woven Fabric Width

    Directory of Open Access Journals (Sweden)

    Shaker Khubab


    Full Text Available A common problem faced in fabric manufacturing is the production of inconsistent fabric width on shuttleless looms in spite of the same fabric specifications. Weft-wise crimp controls the fabric width and it depends on a number of factors, including warp tension, temple type, fabric take-up pressing tension and loom working width. The aim of this study is to investigate the effect of these parameters on the fabric width produced. Taguchi’s orthogonal design was used to optimise the weaving parameters for obtaining controlled fabric width. On the basis of signal to noise ratios, it could be concluded that controlled fabric width could be produced using medium temple type and intense take-up pressing tension at relatively lower warp tension and smaller loom working width. The analysis of variance revealed that temple needle size was the most significant factor affecting the fabric width, followed by loom working width and warp tension, whereas take-up pressing tension was least significant of all the factors investigated in the study.

  10. Potential for Fabric Damage by Welding Electron Beam (United States)

    Fragomeni, James M.; Nunes, Arthur C., Jr.


    Welding electron beam effects on Nextel AF-62 ceramic fabric enable a preliminary, tentative interpretation of electron beam fabric damage. Static surface charging does not protect fabric from beam penetration, but penetration occurs only after a delay time. The delay time is thought to be that required for the buildup of outgassing products at the fabric surface to a point where arcing occurs. Extra long delays are noted when the gun is close enough to the surface to be shut off by outgassing emissions. Penetration at long distances is limited by beam attenuation from electronic collisions with the chamber atmosphere.

  11. Geometrical Modeling of Woven Fabrics Weavability-Limit New Relationships

    Directory of Open Access Journals (Sweden)

    Dalal Mohamed


    Full Text Available The weavability limit and tightness for 2D and 3D woven fabrics is an important factor and depends on many geometric parameters. Based on a comprehensive review of the literature on textile fabric construction and property, and related research on fabric geometry, a study of the weavability limit and tightness relationships of 2D and 3D woven fabrics was undertaken. Experiments were conducted on a representative number of polyester and cotton woven fabrics which have been woven in our workshop, using three machines endowed with different insertion systems (rapier, projectiles and air jet. Afterwards, these woven fabrics have been analyzed in the laboratory to determine their physical and mechanical characteristics using air permeability-meter and KES-F KAWABATA Evaluation System for Fabrics. In this study, the current Booten’s weavability limit and tightness relationships based on Ashenhurst’s, Peirce’s, Love’s, Russell’s, Galuszynskl’s theory and maximum-weavability is reviewed and modified as new relationships to expand their use to general cases (2D and 3D woven fabrics, all fiber materiel, all yarns etc…. The theoretical relationships were examined and found to agree with experimental results. It was concluded that the weavability limit and tightness relationships are useful tools for weavers in predicting whether a proposed fabric construction was weavable and also in predicting and explaining their physical and mechanical properties.

  12. Influence of Weave into Slippage of Yarns in Woven Fabric

    Directory of Open Access Journals (Sweden)



    Full Text Available Slippage resistance of yarns at a seam in woven fabrics is a very important factor and very strict claims are raised for this property. It is necessary to know how fabric structure influences on seam slippage quality before manufacturing the fabric. The purpose of this work was to establish which of the weave factor is most suitable to describe balanced weave fabrics seam slippage. It was investigated seam slippage characteristics in the fabric and the factor was offered, which characterizes best fabric structure from the thread slippage point of view. Fifteen wool fabrics, which differ only on weave were weaved for investigations. The test was carried out according to LST EN ISO 13936-1standard. First of all, the well known factors such as fabric structure factor P and average float F were investigated and then a new fabric structure factor was offered, which the best characterizes the weave from thread slippage point of view. The proposed model shows good correlation between experimental and theoretical values of the new weave factor.

  13. Fabrication and characterization of non-linear parabolic microporous membranes. (United States)

    Rajasekaran, Pradeep Ramiah; Sharifi, Payam; Wolff, Justin; Kohli, Punit


    Large scale fabrication of non-linear microporous membranes is of technological importance in many applications ranging from separation to microfluidics. However, their fabrication using traditional techniques is limited in scope. We report on fabrication and characterization of non-linear parabolic micropores (PMS) in polymer membranes by utilizing flow properties of fluids. The shape of the fabricated PMS corroborated well with simplified Navier-Stokes equation describing parabolic relationship of the form L - t(1/2). Here, L is a measure of the diameter of the fabricated micropores during flow time (t). The surface of PMS is smooth due to fluid surface tension at fluid-air interface. We demonstrate fabrication of PMS using curable polydimethylsiloxane (PDMS). The parabolic shape of micropores was a result of interplay between horizontal and vertical fluid movements due to capillary, viscoelastic, and gravitational forces. We also demonstrate fabrication of asymmetric "off-centered PMS" and an array of PMS membranes using this simple fabrication technique. PMS containing membranes with nanoscale dimensions are also possible by controlling the experimental conditions. The present method provides a simple, easy to adopt, and energy efficient way for fabricating non-linear parabolic shape pores at microscale. The prepared parabolic membranes may find applications in many areas including separation, parabolic optics, micro-nozzles / -valves / -pumps, and microfluidic and microelectronic delivery systems.

  14. Adaptive Robotic Fabrication for Conditions of Material Inconsistency

    DEFF Research Database (Denmark)

    Nicholas, Paul; Zwierzycki, Mateusz; Clausen Nørgaard, Esben


    metal sheet. The paper focuses on the issue of geometric inaccuracies associated with material springback that are experienced in the making of a research demonstrator. It asks how to fabricate in conditions of material inconsistency, and how might adaptive models negotiate between the design model...... and the fabrication process? Here, two adaptive methods are presented that aim to increase forming accuracy with only a minimum increase in fabrication time, and that maintain ongoing input from the results of the fabrication process. The first method is an online sensor-based strategy and the second method...... is an offline predictive strategy based on machine learning. Rigidisation of thin metal skins...

  15. Comparison of Quantitative Antifungal Testing Methods for Textile Fabrics. (United States)

    Imoto, Yasuo; Seino, Satoshi; Nakagawa, Takashi; Yamamoto, Takao A


     Quantitative antifungal testing methods for textile fabrics under growth-supportive conditions were studied. Fungal growth activities on unfinished textile fabrics and textile fabrics modified with Ag nanoparticles were investigated using the colony counting method and the luminescence method. Morphological changes of the fungi during incubation were investigated by microscopic observation. Comparison of the results indicated that the fungal growth activity values obtained with the colony counting method depended on the morphological state of the fungi on textile fabrics, whereas those obtained with the luminescence method did not. Our findings indicated that unique characteristics of each testing method must be taken into account for the proper evaluation of antifungal activity.

  16. Turbine airfoil fabricated from tapered extrusions (United States)

    Marra, John J


    An airfoil (30) and fabrication process for turbine blades with cooling channels (26). Tapered tubes (32A-32D) are bonded together in a parallel sequence, forming a leading edge (21), a trailing edge (22), and pressure and suction side walls (23, 24) connected by internal ribs (25). The tapered tubes may be extruded without camber to simplify the extrusion process, then bonded along matching surfaces (34), forming a non-cambered airfoil (28), which may be cambered in a hot forming process and cut (48) to length. The tubes may have tapered walls that are thinner at the blade tip (T1) than at the base (T2), reducing mass. A cap (50) may be attached to the blade tip. A mounting lug (58) may be forged (60) on the airfoil base and then machined, completing the blade for mounting in a turbine rotor disk.

  17. Transparent Ceramic Scintillator Fabrication, Properties and Applications

    Energy Technology Data Exchange (ETDEWEB)

    Cherepy, N J; Kuntz, J D; Roberts, J J; Hurst, T A; Drury, O B; Sanner, R D; Tillotson, T M; Payne, S A


    Transparent ceramics offer an alternative to single crystals for scintillator applications such as gamma ray spectroscopy and radiography. We have developed a versatile, scaleable fabrication method, using Flame Spray Pyrolysis (FSP) to produce feedstock which is readily converted into phase-pure transparent ceramics. We measure integral light yields in excess of 80,000 Ph/MeV with Cerium-doped Garnets, and excellent optical quality. Avalanche photodiode readout of Garnets provides resolution near 6%. For radiography applications, Lutetium Oxide offers a high performance metric and is formable by ceramics processing. Scatter in transparent ceramics due to secondary phases is the principal limitation to optical quality, and afterglow issues that affect the scintillation performance are presently being addressed.

  18. Tenth target fabrication specialists` meeting: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Foreman, L.R.; Stark, J.C. [comp.


    This tenth meeting of specialists in target fabrication for inertial confinement is unique in that it is the first meeting that was completely unclassified. As a result of the new classification, we were able to invite more foreign participation. In addition to participants from the US, UK, and Canada, representatives from France, Japan, and two Russian laboratories attended, about 115 in all. This booklet presents full papers and poster sessions. Indirect and direct drive laser implosions are considered. Typical topics include: polymer or aluminium or resorcinol/formaldehyde shells, laser technology, photon tunneling microscopy as a characterization tool, foams, coatings, hohlraums, and beryllium capsules. Hydrogen, deuterium, tritium, and beryllium are all considered as fuels.

  19. Superamphiphobic miniature boat fabricated by laser micromachining (United States)

    Yin, Kai; Dong, Xinran; Zhang, Fan; Wang, Cong; Duan, Ji'an


    We fabricated a superamphiphobic miniature boat with marked drag reduction and excellent loading capacity using femtosecond laser direct writing technology. The as-prepared superamphiphobic surface of the boat exhibited apparent contact angles larger than 150° toward both water and oil. Miniature boats with the superamphiphobic surface slid effortlessly on both water and oil-polluted water surfaces, with an increase in sliding distance by up to 52% and load increase of up to 27% compared with those of a boat with an untreated surface. A potential mechanism that explains the excellent performance of the superamphiphobic miniature boat was also discussed. This work provides a simple and economically viable strategy to obtain advanced surfaces for use in microfluidics and marine engineering.

  20. Silicon photonics and challenges for fabrication (United States)

    Feilchenfeld, N. B.; Nummy, K.; Barwicz, T.; Gill, D.; Kiewra, E.; Leidy, R.; Orcutt, J. S.; Rosenberg, J.; Stricker, A. D.; Whiting, C.; Ayala, J.; Cucci, B.; Dang, D.; Doan, T.; Ghosal, M.; Khater, M.; McLean, K.; Porth, B.; Sowinski, Z.; Willets, C.; Xiong, C.; Yu, C.; Yum, S.; Giewont, K.; Green, W. M. J.


    Silicon photonics is rapidly becoming the key enabler for meeting the future data speed and volume required by the Internet of Things. A stable manufacturing process is needed to deliver cost and yield expectations to the technology marketplace. We present the key challenges and technical results from both 200mm and 300mm facilities for a silicon photonics fabrication process which includes monolithic integration with CMOS. This includes waveguide patterning, optical proximity correction for photonic devices, silicon thickness uniformity and thick material patterning for passive fiber to waveguide alignment. The device and process metrics show that the transfer of the silicon photonics process from 200mm to 300mm will provide a stable high volume manufacturing platform for silicon photonics designs.

  1. Fabrication of silicon molds for polymer optics

    DEFF Research Database (Denmark)

    Nilsson, Daniel; Jensen, Søren; Menon, Aric Kumaran


    A silicon mold used for structuring polymer microcavities for optical applications is fabricated, using a combination of DRIE (deep reactive ion etching) and anisotropic chemical wet etching with KOH + IPA. For polymer optical microcavities, low surface roughness and vertical sidewalls are often...... needed. This is achieved by aligning the mold precisely to the [110] direction of a silicon (100) wafer and etching very close to the (110) surfaces using a DRIE Bosch process. The surface roughness of the sidewalls is then removed with a short etch in KOH + IPA. To achieve this, the parameters for DRIE...... and KOH + IPA etch have been optimized. To reduce stiction between the silicon mold and the polymers used for molding, the mold is coated with a teflon-like material using the DRIE system. Released polymer microstructures characterized with AFM and SEM are also presented....

  2. Fabrication and properties of multiferroic nanocomposite films

    KAUST Repository

    Al-Nassar, Mohammed Y.


    A new type of multiferroic polymer nanocomposite is presented, which exhibits excellent ferromagnetism and ferroelectricity simultaneously at room temperature. The multiferroic nanocomposite consists of a ferroelectric copolymer poly(vinylindene fluoride-trifluoroethylene) [P(VDF-TrFE)] and high aspect ratio ferromagnetic nickel (Ni) nanowires (NWs), which were grown inside anodic aluminum oxide membranes. The fabrication of nanocomposite films with Ni NWs embedded in P(VDF-TrFE) has been successfully carried out via a simple low-temperature spin-coating technique. Structural, ferromagnetic, and ferroelectric properties of the developed nanocomposite have been investigated. The remanent and saturation polarization as well as the coercive field of the ferroelectric phase are slightly affected by the incorporation of the NWs as well as the thickness of the films. While the former two decrease, the last increases by adding the NWs or increasing the thickness. The ferromagnetic properties of the nanocomposite films are found to be isotropic.

  3. Photonic crystals physics, fabrication and applications

    CERN Document Server

    Ohtaka, Kazuo


    "Photonic Crystals" details recent progress in the study of photonic crystals, ranging from fundamental aspects to up-to-date applications, in one unified treatment It covers most of the worldwide frontier fields in photonic crystals, including up-to-date fabrication techniques, recent and future technological applications, and our basic understanding of the various optical properties of photonic crystals Brand-new theoretical and experimental data are also presented The book is intended for graduate course students and specialists actively working in this field, but it will also be useful for newcomers, especially the extensive chapter dealing with fundamental aspects of photonic crystals, which paves the way to a full appreciation of the other topics addressed

  4. Fabrication and Multiprobe Electrical Characterization of Nanostructures

    DEFF Research Database (Denmark)

    Klarskov, Mikkel Buster


    Engineering of graphene for modifying electrical properties, such as opening an electronic band gap, has been shown both theoretically and experimentally by creating periodic holes in the graphene sheet, however at the price of lower carrier mobility. Such holes can be made with special fabrication...... to the current direction. The results show a decrease in carrier mobility with increasing number of rows, but does not indicate a band gap opening with holes sizes of 50 nm and a pitch of 100 nm, which suggests that smaller holes and pitch are necessary for creating band gap in graphene. Electrical...... characterization of graphene and other nanostructures usually involves lithographic processing which can alter or damage fragile materials, and metal electrodes are permanently placed to the sample. This project presents a fast method for electrical characterization for graphene and other nanostructures by the use...

  5. Fabrication of a novel quartz micromachined gyroscope (United States)

    Xie, Liqiang; Xing, Jianchun; Wang, Haoxu; Wu, Xuezhong


    A novel quartz micromachined gyroscope is proposed in this paper. The novel gyroscope is realized by quartz anisotropic wet etching and 3-dimensional electrodes deposition. In the quartz wet etching process, the quality of Cr/Au mask films affecting the process are studied by experiment. An excellent mask film with 100 Å Cr and 2000 Å Au is achieved by optimization of experimental parameters. Crystal facets after etching seriously affect the following sidewall electrodes deposition process and the structure's mechanical behaviours. Removal of crystal facets is successfully implemented by increasing etching time based on etching rate ratios between facets and crystal planes. In the electrodes deposition process, an aperture mask evaporation method is employed to prepare electrodes on 3-dimensional surfaces of the gyroscope structure. The alignments among the aperture masks are realized by the ABM™ Mask Aligner System. Based on the processes described above, a z-axis quartz gyroscope is fabricated successfully.

  6. Fabrication of Microscale Carbon Nanotube Fibers

    Directory of Open Access Journals (Sweden)

    Gengzhi Sun


    Full Text Available Carbon nanotubes (CNTs have excellent mechanical, chemical, and electronic properties, but realizing these excellences in practical applications needs to assemble individual CNTs into larger-scale products. Recently, CNT fibers demonstrate the potential of retaining CNT's superior properties at macroscale level. High-performance CNT fibers have been widely obtained by several fabrication approaches. Here in this paper, we review several key spinning techniques including surfactant-based coagulation spinning, liquid-crystal-based solution spinning, spinning from vertical-aligned CNT arrays, and spinning from CNT aerogel. The method, principle, limitations, and recent progress of each technique have been addressed, and the fiber properties and their dependences on spinning parameters are also discussed.

  7. Design & fabrication of cantilever array biosensors

    DEFF Research Database (Denmark)

    Boisen, Anja; Thundat, T


    Surface immobilization of functional receptors on microfabricated cantilever arrays offers a new paradigm for the development of biosensors based on nanomechanics. Microcantilever-based systems are capable of real-time, multiplexed detection of unlabeled disease markers in extremely small volumes......, electronic processing, and even local telemetry on a single chip have the potential of satisfying the need for highly sensitive and selective multiple-target detection in very small samples. Here we will review the design and fabrication process of cantilever-based biosensors.......Surface immobilization of functional receptors on microfabricated cantilever arrays offers a new paradigm for the development of biosensors based on nanomechanics. Microcantilever-based systems are capable of real-time, multiplexed detection of unlabeled disease markers in extremely small volumes...

  8. Fabrication and Characterization of Cobalt Microbars (United States)

    Useche, Diego; Gelvez, Ciro; Patino, Edgar J.; Basile, Leonardo; Superconductivity; Nanodevices Laboratory Team

    Magnetic materials have been widely used in applications such as data storage, magnetic tunnel junctions and spin valve structures. In the present work we explore the shape anisotropy of a millimeter size array of magnetic microbars. For this study we focused on Cobalt microbars fabricated using photolithography, thermal evaporation and sputtering techniques. Magnetization measurements as a function of angle were performed on microbars samples which differ slightly in their dimensions. The measurements were carried out using vibrating sample magnetometry (VSM) and magnetic optic kerr effect (MOKE). Also, computer simulations in OOMMF were done in order to simulate the experimental results. Despite the bars being in the micrometer scale a small shape anisotropy was observed. Furthermore, when the applied field was parallel to the microbars the maximum coercivity was found and decreased slightly as the field rotated towards the perpendicular direction. It was also found a sheared hysteresis loop in one of the samples.

  9. Method of fabricating a catalytic structure (United States)

    Rollins, Harry W [Idaho Falls, ID; Petkovic, Lucia M [Idaho Falls, ID; Ginosar, Daniel M [Idaho Falls, ID


    A precursor to a catalytic structure comprising zinc oxide and copper oxide. The zinc oxide has a sheet-like morphology or a spherical morphology and the copper oxide comprises particles of copper oxide. The copper oxide is reduced to copper, producing the catalytic structure. The catalytic structure is fabricated by a hydrothermal process. A reaction mixture comprising a zinc salt, a copper salt, a hydroxyl ion source, and a structure-directing agent is formed. The reaction mixture is heated under confined volume conditions to produce the precursor. The copper oxide in the precursor is reduced to copper. A method of hydrogenating a carbon oxide using the catalytic structure is also disclosed, as is a system that includes the catalytic structure.

  10. Design and fabrication of novel photodetector arrays (United States)

    Li, Mary J.; Allen, Christine A.; Aslam, Shahid; Chen, Tina C.; Finkbeiner, Fred M.; Gordon, Scott A.; Kuhn, Jonathan L.; Mott, David B.; Stahle, Carl M.; Stahle, Caroline K.; Tralshawala, Nilesh; Wang, Liqin L.


    We are developing novel photodetector arrays based on superconducting transition-edge sensor (TES) and pop-up detector (PUD) technologies. The TES has the potential for a new generation of high sensitivity photodetectors from the IR to the x-ray. This is directly due to the sharpness of the resistance change with temperature at the superconducting transition. The TESs are deposited on the PUD arrays and serve as the sensing elements. The PUDs are close-packed, folded membrane arrays that provide the TES substrate and the thermal isolation required by the bolometers and microcalorimeters. This paper presents the processing-related characterization result of preliminary TES and PUD designs. The gaol of this work is to fabricate a new generation of x-ray calorimeters and IR bolometers for space flight projects.

  11. Fabric defect segmentation using multichannel blob detectors (United States)

    Kumar, Ajay; Pang, Grantham


    The problem of automated defect detection in textured materials is investigated. A new algorithm based on multichannel filtering is presented. The texture features are extracted by filtering the acquired image using a filter bank consisting of a number of real Gabor functions, with multiple narrow spatial frequency and orientation channels. For each image, we propose the use of image fusion to multiplex the information from sixteen different channels obtained in four orientations. Adaptive degrees of thresholding and the associated effect on sensitivity to material impurities are discussed. This algorithm realizes large computational savings over the previous approaches and enables high-quality real-time defect detection. The performance of this algorithm has been tested thoroughly on real fabric defects, and experimental results have confirmed the usefulness of the approach.

  12. Fabrication of advanced design (grooved) cermet anodes

    Energy Technology Data Exchange (ETDEWEB)

    Windisch, C.F. Jr. [Pacific Northwest Lab., Richland, WA (United States); Huettig, F.R. [Ceramic Magnetics, Inc., Fairfield, NJ (United States)


    Attempts were made to fabricate full-size anodes with advanced, or grooved, design using isostatic pressing, slip casting injection molding. Of the three approaches, isostatic pressing produced an anode with dimensions nearest to the target specifications, without serious macroscopic flaws. This approach is considered the most promising for making advanced anodes for aluminum smelting. However, significant work still remains to optimize the physical properties and microstructure of the anode, both of which were significantly different from that of previous anodes. Injection molding and slip casting yielded anode materials with serious deficiencies, including cracks and holes. Injection molding gave cermet material with the best intrinsic microstructure, i.e., the microstructure of the material between macroscopic flaws was very similar to that of anodes previously made at PNL. Reason for the similarity may have to do with amount of residual binder in the material prior to sintering.

  13. Batch fabrication of nanotubes suspended between microelectrodes

    DEFF Research Database (Denmark)

    Mateiu, Ramona Valentina; Stöckli, T.; Knapp, H. F.


    We report a fabrication method, which uses standard UV-lithography to pattern the catalyst for the chemical vapour deposition(CVD) of suspended double clamped single walled carbon nanotubes. By using an aqueous solution of Fe(NO3)3 the patterning of the catalyst material onto microelectrodes can...... be done with a simple lift-off process with standard photolithographic resist. An applied electric field is sustained between the microelectrodes during CVD to guide the nanotube growth. Comparison with simulations shows that the location and the orientation of the grown carbon nanotubes (CNT) correspond...... to the regions of maximum electric field, enabling accurate positioning of a nanotube by controlling the shape of the microelectrodes. The CNT bridges are deflected tens of nm when a DC voltage is applied between the nanotube and a gate microelectrode indicating that the clamping through the catalyst particles...

  14. Fabrication of Li-intercalated bilayer graphene

    Directory of Open Access Journals (Sweden)

    K. Sugawara


    Full Text Available We have succeeded in fabricating Li-intercalated bilayer graphene on silicon carbide. The low-energy electron diffraction from Li-deposited bilayer graphene shows a sharp 3×3R30° pattern in contrast to Li-deposited monolayer graphene. This indicates that Li atoms are intercalated between two adjacent graphene layers and take the same well-ordered superstructure as in bulk C6Li. The angle-resolved photoemission spectroscopy has revealed that Li atoms are fully ionized and the π bands of graphene are systematically folded by the superstructure of intercalated Li atoms, producing a snowflake-like Fermi surface centered at the Γ point. The present result suggests a high potential of Li-intercalated bilayer graphene for application to a nano-scale Li-ion battery.

  15. Closeout of JOYO-1 Specimen Fabrication Efforts

    Energy Technology Data Exchange (ETDEWEB)

    ME Petrichek; JL Bump; RF Luther


    Fabrication was well under way for the JOYO biaxial creep and tensile specimens when the NR Space program was canceled. Tubes of FS-85, ASTAR-811C, and T-111 for biaxial creep specimens had been drawn at True Tube (Paso Robles, CA), while tubes of Mo-47.5 Re were being drawn at Rhenium Alloys (Cleveland, OH). The Mo-47.5 Re tubes are now approximately 95% complete. Their fabrication and the quantities produced will be documented at a later date. End cap material for FS-85, ASTAR-811C, and T-111 had been swaged at Pittsburgh Materials Technology, Inc. (PMTI) (Large, PA) and machined at Vangura (Clairton, PA). Cutting of tubes, pickling, annealing, and laser engraving were in process at PMTI. Several biaxial creep specimen sets of FS-85, ASTAR-811C, and T-111 had already been sent to Pacific Northwest National Laboratory (PNNL) for weld development. In addition, tensile specimens of FS-85, ASTAR-811C, T-111, and Mo-47.5 Re had been machined at Kin-Tech (North Huntington, PA). Actual machining of the other specimen types had not been initiated. Flowcharts 1-3 detail the major processing steps each piece of material has experienced. A more detailed description of processing will be provided in a separate document [B-MT(SRME)-51]. Table 1 lists the in-process materials and finished specimens. Also included are current metallurgical condition of these materials and specimens. The available chemical analyses for these alloys at various points in the process are provided in Table 2.

  16. Spacecraft fabrication and test MODIL. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Saito, T.T.


    This report covers the period from October 1992 through the close of the project. FY 92 closed out with the successful briefing to industry and with many potential and important initiatives in the spacecraft arena. Due to the funding uncertainties, we were directed to proceed as if our funding would be approximately the same as FY 92 ($2M), but not to make any major new commitments. However, the MODIL`s FY 93 funding was reduced to $810K and we were directed to concentrate on the cryocooler area. The cryocooler effort completed its demonstration project. The final meetings with the cryocooler fabricators were very encouraging as we witnessed the enthusiastic reception of technology to help them reduce fabrication uncertainties. Support of the USAF Phillips Laboratory cryocooler program was continued including kick-off meetings for the Prototype Spacecraft Cryocooler (PSC). Under Phillips Laboratory support, Gill Cruz visited British Aerospace and Lucas Aerospace in the United Kingdom to assess their manufacturing capabilities. In the Automated Spacecraft & Assembly Project (ASAP), contracts were pursued for the analysis by four Brilliant Eyes prime contractors to provide a proprietary snap shot of their current status of Integrated Product Development. In the materials and structure thrust the final analysis was completed of the samples made under the contract (``Partial Automation of Matched Metal Net Shape Molding of Continuous Fiber Composites``) to SPARTA. The Precision Technologies thrust funded the Jet Propulsion Laboratory to prepare a plan to develop a Computer Aided Alignment capability to significantly reduce the time for alignment and even possibly provide real time and remote alignment capability of systems in flight.

  17. Localized Corrosion of Alloy 22 -Fabrication Effects-

    Energy Technology Data Exchange (ETDEWEB)

    Rebak, R B


    This report deals with the impact of fabrication processes on the localized corrosion behavior of Alloy 22 (N06022). The four fabrication processes that were analyzed are: (1) Surface stress mitigation of final closure weld, (2) Manufacturing of the mockup container, (3) Black annealing of the container and (4) Use of different heats of Alloy 22 for container fabrication. Immersion and Electrochemical tests performed in the laboratory are generally aggressive and do not represent actual repository environments in Yucca Mountain. For example, to determine the intergranular attack in the heat affected zone of a weldment, tests are conducted in boiling acidic and oxidizing solutions according to ASTM standards. These solutions are used to compare the behavior of differently treated metallic coupons. Similarly for electrochemical tests many times pure sodium chloride or calcium chloride solutions are used. Pure chloride solutions are not representative of the repository environment. (1) Surface Stress Mitigation: When metallic plates are welded, for example using the Gas Tungsten Arc Welding (GTAW) method, residual tensile stresses may develop in the vicinity of the weld seam. Processes such as Low Plasticity Burnishing (LPB) and Laser Shock Peening (LSP) could be applied locally to eliminate the residual stresses produced by welding. In this study, Alloy 22 plates were welded and then the above-mentioned surface treatments were applied to eliminate the residual tensile stresses. The aim of the current study was to comparatively test the corrosion behavior of as-welded (ASW) plates with the corrosion behavior of plates with stress mitigated surfaces. Immersion and electrochemical tests were performed. Results from both immersion and electrochemical corrosion tests show that the corrosion resistance of the mitigated plates was not affected by the surface treatments applied. (2) Behavior of Specimens from a Mockup container: Alloy 22 has been extensively tested for

  18. Fabrication of Te and Te-Au Nanowires-Based Carbon Fiber Fabrics for Antibacterial Applications. (United States)

    Chou, Ting-Mao; Ke, Yi-Yun; Tsao, Yu-Hsiang; Li, Ying-Chun; Lin, Zong-Hong


    Pathogenic bacteria that give rise to diseases every year remain a major health concern. In recent years, tellurium-based nanomaterials have been approved as new and efficient antibacterial agents. In this paper, we developed the approach to directly grow tellurium nanowires (Te NWs) onto commercial carbon fiber fabrics and demonstrated their antibacterial activity. Those Te NWs can serve as templates and reducing agents for gold nanoparticles (Au NPs) to deposit. Three different Te-Au NWs with varied concentration of Au NPs were synthesized and showed superior antibacterial activity and biocompability. These results indicate that the as-prepared carbon fiber fabrics with Te and Te-Au NWs can become antimicrobial clothing products in the near future.

  19. Study on micro fabricated stainless steel surface to anti-biofouling using electrochemical fabrication (United States)

    Hwang, Byeong Jun; Lee, Sung Ho


    Biofilm formed on the surface of the object by the microorganism resulting in fouling organisms. This has led to many problems in daily life, medicine, health and industrial community. In this study, we tried to prevent biofilm formation on the stainless steel (SS304) sheet surface with micro fabricated structure. After then forming the microscale colloid patterns on the surface of stainless steel by using an electrochemical etching forming a pattern by using a FeCl3 etching was further increase the surface roughness. Culturing the Pseudomonas aeruginosa on the stainless steel fabricated with a micro structure on the surface was observed a relationship between the surface roughness and the biological fouling of the micro structure. As a result, the stainless steel surface with a micro structure was confirmed to be the biological fouling occurs less. We expect to be able to solve the problems caused by biological fouling in various fields such as medicine, engineering, using this research.

  20. Fabrication of hierarchical ZnO nanostructures on cotton fabric for wearable device applications (United States)

    Pandiyarasan, V.; Suhasini, S.; Archana, J.; Navaneethan, M.; Majumdar, Abhijit; Hayakawa, Y.; Ikeda, H.


    We have investigated ZnO nanostructures on cotton fabric (CF) s a flexible material for an application of wearable thermoelectric (TE) power generator which requires super-hydrophobicity, UV protection, and high TE efficiency. Field emission scanning electron microscopy images revealed that the formed ZnO nanostructures have a mixture of nanorods and nanosheets and are uniformly coated on the CF. XRD pattern and Raman spectra revealed that the ZnO nanostructure has a wurtzite structure. Contact angle measurements showed that the ZnO-nanostructures-coated CF possessed a high super hydrophobic nature with an angle of 132.5°. ZnO nanocomposite/CF sample exhibited an excellent UV protection factor 183.84. Seebeck coefficient, electrical resistivity and thermoelectric power factor of the ZnO nanostructures on cotton fabric were evaluated to be 28 μV/K, 0.04 Ω-cm, and 22 μW/m K2, respectively.

  1. Combined Compression and Shear Structural Evaluation of Stiffened Panels Fabricated Using Electron Beam Freeform Fabrication


    Nelson, Erik Walter


    Unitized aircraft structures have the potential to be more efficient than current aircraft structures. The Electron Beam Freeform Fabrication (EBF3) process can be used to manufacture unitized aircraft structures. The structural efficiency of blade stiffened panels made with EBF3 was compared to panels made by integrally machining from thick plate. The panels were tested under two load cases in a combined compression-shear load test fixture. One load case tested the panels' responses to a...

  2. Fabrication and Characterization of Superconductive Coplanar Waveguide Resonators : Fabrication and Characterization of Superconductive Coplanar Waveguide Resonators


    Ergül, Adem


    The objective of this thesis is to evaluate a generic process for fabrication and characterization of the Superconductive coplanar waveguide (CPW) resonators. Superconductive CPW resonators with various lengths and shapes are designed to investigate their electrical and magnetic properties as well as resonance properties and sensitivities. In the first part of thesis, two different models are introduced in order to estimate the nonlinear kinetic inductance of a superconducting CPW resonator. ...

  3. Fabrication and Design of Optical Nanomaterials (United States)

    Huntington, Mark D.

    Over the past several decades, advances in nanometer scale fabrication has sparked interes in applications that take advantage of materials that are structured at these small length scales. Specifically, metallic optical nanomaterials have emerged as a new way to control light at length scales that are smaller than the wavelength of light and have optical properties that are distinctly different from their macroscale counterparts. Although there have been may advances in nanofabrication, the performance and widespread use of optical nanomaterials is still limited by fabrication and design challenges. This dissertation describes advances in the fabrication, characterization, and design of optical nanomaterials. First we demonstrate how a portable and compact photolithography system can be made using a light source composed of UV LEDs. Our solid-state photolithography (SSP) system brings the capabilities of one of the most important yet workhorse tools of micro- and nanotechnology--the mask aligner--to the benchtop. The two main highlights of chapter 2 include: (i) portable, low-cost photolithography and (ii) high quality patterning. We replace the mask aligner with a system composed of UV LEDs and a diffuser that can be built for as little as $30. The design of the SSP system alleviates the need for dedicated power supplies, vacuum lines and cooling systems, which makes it a true benchtop photolithography system. We further show that sub-wavelength features can be fabricated across 4-in wafers and that these patterns are of high quality such that they can be easily transferred into functional materials. Chapter 3 describes a parallel method to create nanometer scale textures over large areas with unprecedented control over wrinkle wavelength. The main points of this chapter include: (i) a new material system for nanowrinkles, (ii) wrinkles with tunable wavelengths, and (iii) a method for measuring the skin thickness. First, we show that RIE treatment of PS with

  4. 49 CFR 192.153 - Components fabricated by welding. (United States)


    ... 49 Transportation 3 2010-10-01 2010-10-01 false Components fabricated by welding. 192.153 Section....153 Components fabricated by welding. (a) Except for branch connections and assemblies of standard... welding, whose strength cannot be determined, must be established in accordance with paragraph UG-101 of...

  5. Panel fabrication utilizing GaAs solar cells (United States)

    Mardesich, N.


    The development of the GaAs solar cells for space applications is described. The activities in the fabrication of GaAs solar panels are outlined. Panels were fabricated while introducing improved quality control, soldering laydown and testing procedures. These panels include LIPS II, San Marco Satellite, and a low concentration panel for Rockwells' evaluation. The panels and their present status are discussed.

  6. Perceptions of seshoeshoe fabric, naming and meanings of motifs

    African Journals Online (AJOL)


    need to have a national identity and embraced the blue “German Print”, or terantala as it was called, the fabric has evolved extensively. The most popular brand of the fabric that was produced was called the Three Cats and this was exported to South Africa. This brand is now produced by the Da Gama Textiles in South.

  7. Automated pilling detection and fuzzy classification of textile fabrics (United States)

    Dar, Iqbal M.; Mahmood, Waqar; Vachtsevanos, George


    In the textile industry, the degree of fabric pilling is subjectively determined by human inspectors resulting in inconsistent quality control. The observed resistance to pilling is reported on an arbitrary scale ranging from No. 5 (no pillings) to No. 1 (very severe pilling). This paper presents a system and a methodology that counts the number of pillings on textile fabric samples automatically and classifies them into one of the pre-defined classes with repeatable accuracy while accounting for the human judgment by allowing the determination of the degree of confidence assigned to the sample's membership in each class. The system consists of an apparatus; an imaging and data processing software procedure for counting the number of pillings; and a methodology for classifying the fabric samples into one of the pre-defined classes with repeatable accuracy while accounting for human judgment. A CCD camera is used to capture successive gray scale images of the fabric sample. A series of segmentation, Radon transform, morphological filtering, and detrending operations are applied to the fabric images to determine the true pilling count. The structuring element for the morphological operations is designed such that fuzz balls (which are not pillings) are filtered. Using fuzzy membership functions, the fabric pilling count is mapped to fabric pilling resistance rating. The system has been successfully tested on a large number of fabric samples with different shades and textures provided by the textile industry.

  8. Fabrication of optochemical and electrochemical sensors using thin ...

    Indian Academy of Sciences (India)

    This paper describes the fabrication of thin films of porphyrin and metallophthalocyanine derivatives on different substrates for the optochemical detection of HCl gas and electrochemical determination of L-cysteine (CySH). Solid state gas sensor for HCl gas was fabricated by coating meso-substituted porphyrin derivatives ...

  9. 21 CFR 884.6140 - Assisted reproduction micropipette fabrication instruments. (United States)


    ... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Assisted reproduction micropipette fabrication... HUMAN SERVICES (CONTINUED) MEDICAL DEVICES OBSTETRICAL AND GYNECOLOGICAL DEVICES Assisted Reproduction Devices § 884.6140 Assisted reproduction micropipette fabrication instruments. (a) Identification...

  10. Piezoresistive effect in top-down fabricated silicon nanowires

    DEFF Research Database (Denmark)

    Reck, Kasper; Richter, Jacob; Hansen, Ole


    We have designed and fabricated silicon test chips to investigate the piezoresistive properties of both crystalline and polycrystalline nanowires using a top-down approach, in order to comply with conventional fabrication techniques. The test chip consists of 5 silicon nanowires and a reference...

  11. Perceptions of seshoeshoe fabric, naming and meanings of motifs

    African Journals Online (AJOL)


    naming. STATEMENT OF THE PROBLEM. Since the 1950s when Basotho women saw a need to have a national identity and embraced the blue “German Print”, or terantala as it was called, the fabric has evolved extensively. The most popular brand of the fabric that was produced was called the Three Cats and this.

  12. Fabrication of glass microchannels by xurography for electrophoresis applications. (United States)

    Pessoa de Santana, Phillipe; Segato, Thiago Pinotti; Carrilho, Emanuel; Lima, Renato Sousa; Dossi, Nicolò; Kamogawa, Marcos Yassuo; Gobbi, Angelo Luiz; Piazzeta, Maria Helena; Piccin, Evandro


    This communication describes a simple and cost-effective method for fabricating glass microchannels by wet chemical etching using masks made by xurography in vinyl adhesive films. Analytical performance of microfluidic devices fabricated using the new approach was evaluated by microchip electrophoresis coupled to capacitively coupled contactless conductivity detection (C(4)D) and laser-induced fluorescence (LIF) detection.

  13. Fabrication and mechanical performance of the ATLAS central solenoid

    CERN Document Server

    Mizumaki, S; Kobayashi, T; Yamaoka, H; Kondo, Y; Kawai, M; Doi, Y; Haruyama, T; Mine, S; Takano, H; Yamamoto, A; Kondo, T; ten Kate, H H J


    Fabrication of the central solenoid for ATLAS detector in the CERN- LHC project was completed, and the performance test has been successfully carried out in Japan. The solenoid has arrived at CERN to be assembled with the LAr calorimeter. This paper describes the fabrication and mechanical, performance of the ATLAS central solenoid. (10 refs).

  14. Fabrication of cell container arrays with overlaid surface topographies

    NARCIS (Netherlands)

    Truckenmüller, R.K.; Giselbrecht, S.; Escalante Marun, M.; Groenendijk, M.N.W.; Groenendijk, M.N.W.; Papenburg, B.J.; Rivron, N.C.; Unadkat, H.V.; Saile, V.; Subramaniam, Vinod; van Blitterswijk, Clemens; van den Berg, Albert; Wessling, Matthias; de Boer, Jan; Stamatialis, Dimitrios

    This paper presents cell culture substrates in the form of microcontainer arrays with overlaid surface topographies, and a technology for their fabrication. The new fabrication technology is based on microscale thermoforming of thin polymer films whose surfaces are topographically prepatterned on a

  15. Bisecting Microfluidic Channels with Metallic Nanowires Fabricated by Nanoskiving

    NARCIS (Netherlands)

    Kalkman, Gerard A; Zhang, Yanxi; Monachino, Enrico; Mathwig, Klaus; Kamminga, Machteld E; Pourhossein Aghbolagh, Parisa; Oomen, Pieter E; Stratmann, Sarah A; Zhao, Zhiyuan; van Oijen, Antoine M; Verpoorte, Elisabeth; Chiechi, Ryan C


    This paper describes the fabrication of millimeter-long gold nanowires that bisect the center of microfluidic channels. We fabricated the nanowires by nanoskiving and then suspended them over a trench in a glass structure. The channel was sealed by bonding it to a complementary

  16. Fabrication of silicon based glass fibres for optical communication

    Indian Academy of Sciences (India)

    Silicon based glass fibres are fabricated by conventional fibre drawing process. First, preform fabrication is carried out by means of conventional MCVD technique by using various dopants such as SiCl4, GeCl4, POCl3, and FeCl3. The chemicals are used in such a way that step index single mode fibre can be drawn.

  17. Fabrication of Superconducting Detectors for Studying the Universe (United States)

    Brown, Ari-David


    Superconducting detectors offer unparalleled means of making astronomical/cosmological observations. Fabrication of these detectors is somewhat unconventional; however, a lot of novel condensed matter physics/materials scientific discoveries and semiconductor fabrication processes can be generated in making these devices.

  18. Flexible and wearable electronic silk fabrics for human physiological monitoring (United States)

    Mao, Cuiping; Zhang, Huihui; Lu, Zhisong


    The development of textile-based devices for human physiological monitoring has attracted tremendous interest in recent years. However, flexible physiological sensing elements based on silk fabrics have not been realized. In this paper, ZnO nanorod arrays are grown in situ on reduced graphene oxide-coated silk fabrics via a facile electro-deposition method for the fabrication of silk-fabric-based mechanical sensing devices. The data show that well-aligned ZnO nanorods with hexagonal wurtzite crystalline structures are synthesized on the conductive silk fabric surface. After magnetron sputtering of gold electrodes, silk-fabric-based devices are produced and applied to detect periodic bending and twisting. Based on the electric signals, the deformation and release processes can be easily differentiated. Human arterial pulse and respiration can also be real-time monitored to calculate the pulse rate and respiration frequency, respectively. Throat vibrations during coughing and singing are detected to demonstrate the voice recognition capability. This work may not only help develop silk-fabric-based mechanical sensing elements for potential applications in clinical diagnosis, daily healthcare monitoring and voice recognition, but also provide a versatile method for fabricating textile-based flexible electronic devices.

  19. Design, fabrication and performance evaluation of a 22-channel ...

    Indian Academy of Sciences (India)

    The indigenous design, fabrication and performance evaluation of ... Therefore it was decided to take up the project of indigenous design and fabrication of a .... acquisition software. A digital IaO card forms the link between the personal computer and the data acquisition hardware. The integrator produces an integrated ...

  20. 25 CFR 307.11 - Certificates fastened to fabrics. (United States)


    ... 25 Indians 2 2010-04-01 2010-04-01 false Certificates fastened to fabrics. 307.11 Section 307.11 Indians INDIAN ARTS AND CRAFTS BOARD, DEPARTMENT OF THE INTERIOR NAVAJO ALL-WOOL WOVEN FABRICS; USE OF... the hand seal press furnished by the Indian Arts and Crafts Board. ...

  1. Advanced trans-tibial socket fabrication using selective laser sintering. (United States)

    Rogers, Bill; Bosker, Gordon W; Crawford, Richard H; Faustini, Mario C; Neptune, Richard R; Walden, Gail; Gitter, Andrew J


    There have been a variety of efforts demonstrating the use of solid freeform fabrication (SFF) for prosthetic socket fabrication though there has been little effort in leveraging the strengths of the technology. SFF encompasses a class of technologies that can create three dimensional objects directly from a geometric database without specific tooling or human intervention. A real strength of SFF is that cost of fabrication is related to the volume of the part, not the part's complexity. For prosthetic socket fabrication this means that a sophisticated socket can be fabricated at essentially the same cost as a simple socket. Adding new features to a socket design becomes a function of software. The work at The University of Texas Health Science Center at San Antonio (UTHSCSA) and University of Texas at Austin (UTA) has concentrated on developing advanced sockets that incorporate structural features to increase comfort as well as built in fixtures to accommodate industry standard hardware. Selective laser sintering (SLS) was chosen as the SFF technology to use for socket fabrication as it was capable of fabricating sockets using materials appropriate for prosthetics. This paper details the development of SLS prosthetic socket fabrication techniques at UTHSCSA/UTA over a six-year period.

  2. Fabrication and Characterisation of Membrane-Based Gold Electrodes

    DEFF Research Database (Denmark)

    Bakmand, Tanya; Kwasny, Dorota; Dimaki, Maria


    This work presents a versatile, membrane based electrochemical sensor with thin film electrodes fabricated through Ebeam evaporation directly on porous materials (membranes). Here, the fabrication of the electrodes is described along with possible methods for integration in fluidic systems and ch...

  3. Fabrication of functional structures on thin silicon nitride membranes

    NARCIS (Netherlands)

    Ekkels, P.; Tjerkstra, R.W.; Krijnen, Gijsbertus J.M.; Berenschot, Johan W.; Brugger, J.P.; Elwenspoek, Michael Curt

    A process to fabricate functional polysilicon structures above large (4×4 mm2) thin (200 nm), very flat LPCVD silicon rich nitride membranes was developed. Key features of this fabrication process are the use of low-stress LPCVD silicon nitride, sacrificial layer etching, and minimization of

  4. Plasma treatment of polyester fabric to impart the water repellency ...

    Indian Academy of Sciences (India)

    silane (DCDMS) gives better water repellency. When cotton fabric was treated earlier with DCDMS, though water repellency property was enhanced, the fabric lost its strength due to hydrochloric acid [HCl] generated during the condensation reaction [8]. So, it is considered necessary to carry out the investigation using a.

  5. Fabrication of micro-Ni arrays by electroless and electrochemical ...

    Indian Academy of Sciences (India)

    Nickel micro-arrays were fabricated by electroless and electrochemical deposition in an etched porous aluminum membrane. The aluminum membrane with metal characteristic could be fabricated from high-purity aluminium by electrochemical method. The aluminum reduced Ni2+ into Ni and the formed Ni nuclei served as ...

  6. Fabricating a custom earpiece for hand-held radios. (United States)

    Potter, James V; Hansen, Nancy A; Schroetlin, Robert G; Jones, John D


    This article describes the fabrication of a custom earpiece for use with hand-held radios. The technique can be used to fabricate custom earpieces, as a public service, for law enforcement personnel, firefighters, emergency medical services (EMS) personnel, and others, improving safety and providing a valuable benefit to the community.

  7. Ultrafast Laser Fabrication of Bragg Waveguides in GLS Chalcogenide Glass

    Directory of Open Access Journals (Sweden)

    McMillen Ben


    Full Text Available We present work on the fabrication of Bragg waveguides in gallium-lanthanum-sulfide chalcogenide glass using an ultrafast laser. Waveguides were written with a single pass while modulating the writing beam. The spatial and temporal profile of the writing beam was ontrolled during waveguide fabrication in order to control the shape and size of the waveguide cross-section.

  8. The spin-valve transistor: Fabrication, characterization and physics

    NARCIS (Netherlands)

    Jansen, R.; van 't Erve, O.M.J.; Kim, S.D.; Vlutters, R.; Anil Kumar, P.S.; Lodder, J.C.


    An overview is given of the fabrication, basic properties, and physics of the spin-valve transistor. We describe the layout of this three-terminal ferromagnet/semiconductor hybrid device, as well as the operating principle. Fabrication technologies are discussed, including vacuum metal bonding. We

  9. Automatic detection of seed coat fragments in cotton fabrics (United States)

    Seed coat fragments (SCF) reduce the marketability of cotton fiber, yarns and fabrics. It is particularly important to measure SCF content in the fabric because they cause severe dyeing and appearance defects. SCF content is greatly affected by cotton varieties, environmental conditions during crop ...

  10. Comparative Evaluation of the Effectiveness of some local Fabrics ...

    African Journals Online (AJOL)

    All fabrics were effective in harvesting species of the copepods, the cladocerans and the large-sized rotifer, Asplanchna. The grey baft and the nylon net were not effective in harvesting the small-sized rotifer species like Keratella, Filinia and Trichocerca.All the fabrics effectively harvested Moina, an excellent freshwater ...

  11. Fabrication of an all-metal atomic force microscope probe

    DEFF Research Database (Denmark)

    Rasmussen, Jan Pihl; Tang, Peter Torben; Hansen, Ole


    This paper presents a method for fabrication of an all-metal atomic force microscope probe (tip, cantilever and support) for optical read-out, using a combination of silicon micro-machining and electroforming. The paper describes the entire fabrication process for a nickel AFM-probe. In addition...

  12. Advective heat transfer and fabric development in a shallow crustal ...

    Indian Academy of Sciences (India)

    Resulting granite mylonites show Y-maximum c axis fabric in completely recrystallized quartz ribbons,dynamic recrystallization of perthites,and myrmekite indicative of fabric development under intermediate temperature (∼500-400° C). The weakly-deformed interior shows myrmekite,feldspar microfracturing and limited ...

  13. LAF-Fabric : Data processing for Linguistic Annotation Framework

    NARCIS (Netherlands)

    Roorda, Dirk


    LAF-fabric is a Python tool for running Python notebooks with access to the information in a LAF resource. The selling point of LAF-fabric is performance, both in terms of speed and memory usage. The second goal is to make it really easy for you to write analytic notebooks straightforwardly in terms

  14. Suspended microstructures of epoxy based photoresists fabricated with UV photolithography

    DEFF Research Database (Denmark)

    Hemanth, Suhith; Anhøj, Thomas Aarøe; Caviglia, Claudia


    In this work we present an easy, fast, reliable and low cost microfabrication technique for fabricating suspended microstructures of epoxy based photoresistswith UV photolithography. Two different fabrication processes with epoxy based resins (SU-8 and mr-DWL) using UV exposures at wavelengths...

  15. Fabrication of keratin-silica hydrogel for biomedical applications

    Energy Technology Data Exchange (ETDEWEB)

    Kakkar, Prachi; Madhan, Balaraman, E-mail:


    In the recent past, keratin has been fabricated into different forms of biomaterials like scaffold, gel, sponge, film etc. In lieu of the myriad advantages of the hydrogels for biomedical applications, a keratin-silica hydrogel was fabricated using tetraethyl orthosilicate (TEOS). Textural analysis shed light on the physical properties of the fabricated hydrogel, inturn enabling the optimization of the hydrogel. The optimized keratin-silica hydrogel was found to exhibit instant springiness, optimum hardness, with ease of spreadability. Moreover, the hydrogel showed excellent swelling with highly porous microarchitecture. MTT assay and DAPI staining revealed that keratin-silica hydrogel was biocompatible with fibroblast cells. Collectively, these properties make the fabricated keratin-silica hydrogel, a suitable dressing material for biomedical applications. - Highlights: • Keratin-silica hydrogel has been fabricated using sol–gel technique. • The hydrogel shows appropriate textural properties. • The hydrogel promotes fibroblast cells proliferation. • The hydrogel has potential soft tissue engineering applications like wound healing.

  16. Towards neuromorphic electronics: Memristors on foldable silicon fabric

    KAUST Repository

    Ghoneim, Mohamed T.


    The advantages associated with neuromorphic computation are rich areas of complex research. We address the fabrication challenge of building neuromorphic devices on structurally foldable platform with high integration density. We present a CMOS compatible fabrication process to demonstrate for the first time memristive devices fabricated on bulk monocrystalline silicon (100) which is next transformed into a flexible thin sheet of silicon fabric with all the pre-fabricated devices. This process preserves the ultra-high integration density advantage unachievable on other flexible substrates. In addition, the memristive devices are of the size of a motor neuron and the flexible/folded architectural form factor is critical to match brain cortex\\'s folded pattern for ultra-compact design.

  17. Functionalization of cotton fabrics through thermal reduction of graphene oxide (United States)

    Cai, Guangming; Xu, Zhenglin; Yang, Mengyun; Tang, Bin; Wang, Xungai


    Graphene oxide (GO) was in-situ reduced on cotton fabrics by a simple heat treatment, which endowed cotton fabrics with multi-functions. GO was coated on the surface of cotton fabric through a conventional ;dip and dry; approach. Reduced graphene oxide (RGO) was obtained from GO in the presence of cotton by heating under the protection of nitrogen. Fourier transform infrared (FTIR) spectroscopy, X-ray photoelectron spectroscopy, Raman spectroscopy and scanning electron microscopy were employed to characterize the complexes of RGO and cotton (RGO/cotton). The RGO/cotton fabrics showed good electrical conductivity, surface hydrophobicity and ultraviolet (UV) protection properties. These properties did not deteriorate significantly after repeated fabric bending and washing.

  18. Fabrication and characterization of monolithic solid oxide fuel cells (United States)

    Minh, N. Q.; Horne, C. R.; Liu, F. S.; Moffatt, D. M.; Staszak, P. R.

    The monolithic solid oxide fuel cell (MSOFC) is an all-ceramic structure in which cell components are configured in a compact corrugated array. The MSOFC shows promise for use in a wide range of sizes (kilowatt to megawatt) and a broad spectrum of applications (electric utility, cogeneration, on-site, and aerospace power). A process based on the tape calendering technique is being developed for the fabrication of the MSOFC. MSOFC single cells have been fabricated by this process without cracking or delamination. Stacks of various sizes have been formed and processed to demonstrate fabricability of the monolithic structure. Extensive physical, chemical, electrical, and electrochemical characterization of fabricated samples has been carried out to confirm the required properties of each cell component. The characterization results reported have been used to support material and fabrication improvements.

  19. Neuronal representation of fabric texture for thermal microenvironment

    Directory of Open Access Journals (Sweden)

    Liu Yuqing


    Full Text Available Fabric, our second skin with moisture and thermal capacity for skin temperature regulation, can arouse feelings of pleasant and discomfort. To examine the neurocognitive ability and emotion of fabric tactile perception under different local temperatures, we used functional magnetic resonance imaging with the same denim fabric stimuli and forearm contact area, and found a functional dissociation: the affective regions was more involved during warm condition, the discriminative regions were more involved during neutral condition and the basis regions were significance during cool condition. The higher local skin temperature environment can result in the improvement of sensitivity and discriminability by dorsal pathway (spatial and ventral pathway (frequency for fabric perception. Our results help to explain how the brain uses internal models to interpret external fabric tactile stimuli with micro environmental changing.


    Directory of Open Access Journals (Sweden)

    Vedat ÖZYAZGAN


    Full Text Available In this paper Ne 30/1 cotton yarn obtained by using pure cotton fibers is employed. 1x1, 2x1 and 3x1 Rib fabrics were knitted with yarns at different gauges. During the knitting process, the tension was kept constant. In order to investigate the relaxation on the knitting process fabric samples were treated using three relaxation processes; dry, wet and full respectively. After each relaxation process, stitches dimensions were measured. As a result of these measurements, it is observed that as the relaxation increases the stitches length decreases while the stitches width increases. In rib knitting, As the fabric stretches increases the stitch length increases. As a result it is observed that as the stitch length increases, the width of the stitches increases linearly. In all rib fabrics, increase in the stitch density leads to an increase in the weight of the fabric.

  1. Nucleophilic Addition of Reactive Dyes on Amidoximated Acrylic Fabrics (United States)

    El-Shishtawy, Reda M.; El-Zawahry, Manal M.; Abdelghaffar, Fatma; Ahmed, Nahed S. E.


    Seven reactive dyes judiciously selected based on chemical structures and fixation mechanisms were applied at 2% owf of shade on amidoximated acrylic fabrics. Amidoximated acrylic fabric has been obtained by a viable amidoximation process. The dyeability of these fabrics was evaluated with respect to the dye exhaustion, fixation, and colour strength under different conditions of temperature and dyeing time. Nucleophilic addition type reactive dyes show higher colour data compared to nucleophilic substitution ones. FTIR studies further implicate the binding of reactive dyes on these fabrics. A tentative mechanism is proposed to rationalize the high fixation yield obtained using nucleophilic addition type reactive dyes. Also, the levelling and fastness properties were evaluated for all dyes used. Excellent to good fastness and levelling properties were obtained for all samples irrespective of the dye used. The result of investigation offers a new method for a viable reactive dyeing of amidoximated acrylic fabrics. PMID:25258720

  2. Micro fabrication of biodegradable polymer drug delivery devices

    DEFF Research Database (Denmark)

    Nagstrup, Johan

    permeability and degradation. These systems are for the majority based on traditional materials used in micro technology, such as SU-8, silicon, poly(methyl methacrylate). The next step in developing these new drug delivery systems is to replace classical micro fabrication materials with biodegradable polymers....... In order to successfully do this, methods for fabricating micro structures in biodegradable polymers need to be developed. The goal of this project has been to develop methods for micro fabrication in biodegradable polymers and to use these methods to produce micro systems for oral drug delivery. This has...... successfully been achieved by fabrication of micro container systems made of poly(Llactic acid) and polycaprolactone. To achieve this, polymer solutions have been developed using the theory of Hansen’s solubility parameters. The solutions are used to fabricate polymer films by spin coating, which are used...

  3. Selective laser etching or ablation for fabrication of devices

    KAUST Repository

    Buttner, Ulrich


    Methods of fabricating devices vial selective laser etching are provided. The methods can include selective laser etching of a portion of a metal layer, e.g. using a laser light source having a wavelength of 1,000 nm to 1,500 nm. The methods can be used to fabricate a variety of features, including an electrode, an interconnect, a channel, a reservoir, a contact hole, a trench, a pad, or a combination thereof. A variety of devices fabricated according to the methods are also provided. In some aspects, capacitive humidity sensors are provided that can be fabricated according to the provided methods. The capacitive humidity sensors can be fabricated with intricate electrodes, e.g. having a fractal pattern such as a Peano curve, a Hilbert curve, a Moore curve, or a combination thereof.

  4. Fabrication of Hydrophobic Nanostructured Surfaces for Microfluidic Control. (United States)

    Morikawa, Kyojiro; Tsukahara, Takehiko


    In the field of micro- and nanofluidics, various kinds of novel devices have been developed. For such devices, not only fluidic control but also surface control of micro/nano channels is essential. Recently, fluidic control by hydrophobic nanostructured surfaces have attracted much attention. However, conventional fabrication methods of nanostructures require complicated steps, and integration of the nanostructures into micro/nano channels makes fabrication procedures even more difficult and complicated. In the present study, a simple and easy fabrication method of nanostructures integrated into microchannels was developed. Various sizes of nanostructures were successfully fabricated by changing the plasma etching time and etching with a basic solution. Furthermore, it proved possible to construct highly hydrophobic nanostructured surfaces that could effectively control the fluid in microchannels at designed pressures. We believe that the fabrication method developed here and the results obtained are valuable contributions towards further applications in the field of micro- and nanofluidics.

  5. Fabrication and Testing of Deflecting Cavities for APS

    Energy Technology Data Exchange (ETDEWEB)

    Mammosser, John; Wang, Haipeng; Rimmer, Robert; Jim, Henry; Katherine, Wilson; Dhakal, Pashupati; Ali, Nassiri; Jim, Kerby; Jeremiah, Holzbauer; Genfa, Wu; Joel, Fuerst; Yawei, Yang; Zenghai, Li


    Jefferson Lab (Newport News, Virginia) in collaboration with Argonne National Laboratory (Argonne, IL) has fabricated and tested four first article, 2.8 GHz, deflecting SRF cavities, for Argonne's Short-Pulse X-ray (SPX) project. These cavities are unique in many ways including the fabrication techniques in which the cavity cell and waveguides were fabricated. These cavity subcomponents were milled from bulk large grain niobium ingot material directly from 3D CAD files. No forming of sub components was used with the exception of the beam-pipes. The challenging cavity and helium vessel design and fabrication results from the stringent RF performance requirements required by the project and operation in the APS ring. Production challenges and fabrication techniques as well as testing results will be discussed in this paper.

  6. Nucleophilic addition of reactive dyes on amidoximated acrylic fabrics. (United States)

    El-Shishtawy, Reda M; El-Zawahry, Manal M; Abdelghaffar, Fatma; Ahmed, Nahed S E


    Seven reactive dyes judiciously selected based on chemical structures and fixation mechanisms were applied at 2% of of shade on amidoximated acrylic fabrics. Amidoximated acrylic fabric has been obtained by a viable amidoximation process. The dyeability of these fabrics was evaluated with respect to the dye exhaustion, fixation, and colour strength under different conditions of temperature and dyeing time. Nucleophilic addition type reactive dyes show higher colour data compared to nucleophilic substitution ones. FTIR studies further implicate the binding of reactive dyes on these fabrics. A tentative mechanism is proposed to rationalize the high fixation yield obtained using nucleophilic addition type reactive dyes. Also, the levelling and fastness properties were evaluated for all dyes used. Excellent to good fastness and levelling properties were obtained for all samples irrespective of the dye used. The result of investigation offers a new method for a viable reactive dyeing of amidoximated acrylic fabrics.

  7. Present and future of non-woven fabric technology

    Energy Technology Data Exchange (ETDEWEB)

    Tsuji, Issei (Idemitsu Kosan Co. Ltd., Tokyo, (Japan))


    Non-woven fabrics which had been in the background as an auxiliary material is now on the surface as such disposable household merchandise as paper diapers, disposable pocket warmes and wet tissue, etc. rapidly get popular. The non-wovens show a large variety of performances according to the difference of the raw materials and the method of manufacture. What is important in the future is the technology of 'order-made' non-wovens, i.e., the complex texturing and the post-fabrication technology. This report describes on the following items: Definition and concept of non-woven fabrics. Market and applications. Production method (Wet process and dry process, bonding and entangling). Type and features (staple type, needle punched type, stitch bonded type, spun bond type, and wet type). Future trends. Reciprocal process. Melt-blown non-woven fabric. Spun-lace non-woven fabric. 5 refs., 3 figs., 4 tabs.

  8. Compound Half-Backed Weave Design For Digital Jacquard Fabric (United States)

    Zhang, Meng; Zhou, Jiu


    Based on layered-combination design mode and compound structure, this paper presents a design method, named compound half-backed weave in order to achieve innovating weave structure and surface effect of fabric. This design method includes primary weaves chosen, half-backed technical points set up and half-backed weave databases established. The fabric produced using compound half-backed weave designed by this method can exhibit a unique half-backed effect that only half of the threads on the fabric surface remain in a state of being covered by adjacent wefts. Compound half-backed weave can not only meets the design need of jacquard fabric with different digital images and effectively improves the efficiency of structural design, but also puts forward new theory and method for innovative design of digital jacquard fabric.

  9. A Rapid Process for Fabricating Gas Sensors

    Directory of Open Access Journals (Sweden)

    Chun-Ching Hsiao


    Full Text Available Zinc oxide (ZnO is a low-toxicity and environmentally-friendly material applied on devices, sensors or actuators for “green” usage. A porous ZnO film deposited by a rapid process of aerosol deposition (AD was employed as the gas-sensitive material in a CO gas sensor to reduce both manufacturing cost and time, and to further extend the AD application for a large-scale production. The relative resistance change (△R/R of the ZnO gas sensor was used for gas measurement. The fabricated ZnO gas sensors were measured with operating temperatures ranging from 110 °C to 180 °C, and CO concentrations ranging from 100 ppm to 1000 ppm. The sensitivity and the response time presented good performance at increasing operating temperatures and CO concentrations. AD was successfully for applied for making ZnO gas sensors with great potential for achieving high deposition rates at low deposition temperatures, large-scale production and low cost.

  10. Fabrication for precision mechanisms. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Gillespie, L.K.


    The fabrication of components and assemblies for miniature precision mechanisms provides a variety of exacting manufacturing challenges. Size alone makes many parts hard to pick up, handle, measure, and install. This same small size causes more distortion or bending during machining, assembly, and welding. Some parts even float on the cleaning and deburring solutions. Tools break easily in very small holes, and surface finishes play an important role in part operation. Twenty-five manufacturing operations were studied to improve the precision of existing machining and assembly techniques. The study included the machining of metals and plastics using techniques new to the manufacture of miniature switches, timers, and actuators. Drilling, tapping, and press-fitting miniature features were evaluated. Fixturing and handling techniques, friction reduction, and the forming of ceramic parts were also studied. Many of the new approaches from this study have been incorporated into existing processes and further refined. Detailed observations have been reported in 33 other Bendix reports and the highlights of those observations are summarized in this study.

  11. MEMS tactile display: from fabrication to characterization (United States)

    Miki, Norihisa; Kosemura, Yumi; Watanabe, Junpei; Ishikawa, Hiroaki


    We report fabrication and characterization of MEMS-based tactile display that can display users various tactile information, such as Braille codes and surface textures. The display consists of 9 micro-actuators that are equipped with hydraulic displacement amplification mechanism (HDAM) to achieve large enough displacement to stimulate the human tactile receptors. HDAM encapsulates incompressible liquids. We developed a liquid encapsulation process, which we termed as Bonding-in-Liquid Technique, where bonding with a UV-curable resin in glycerin is conducted in the liquid, which prevented interfusion of air bubbles and deformation of the membrane during the bonding. HDAM successfully amplified the displacement generated by piezoelectric actuators by a factor of 6. The display could virtually produce "rough" and "smooth" surfaces, by controlling the vibration frequency, displacement, and the actuation periods of an actuator until the adjacent actuator was driven. We introduced a sample comparison method to characterize the surfaces, which involves human tactile sensation. First, we prepared samples whose mechanical properties are known. We displayed a surface texture to the user by controlling the parameters and then, the user selects a sample that has the most similar surface texture. By doing so, we can correlate the parameters with the mechanical properties of the sample as well as find the sets of the parameters that can provide similar tactile information to many users. The preliminary results with respect to roughness and hardness is presented.

  12. Material fabrication using acoustic radiation forces (United States)

    Sinha, Naveen N.; Sinha, Dipen N.; Goddard, Gregory Russ


    Apparatus and methods for using acoustic radiation forces to order particles suspended in a host liquid are described. The particles may range in size from nanometers to millimeters, and may have any shape. The suspension is placed in an acoustic resonator cavity, and acoustical energy is supplied thereto using acoustic transducers. The resulting pattern may be fixed by using a solidifiable host liquid, forming thereby a solid material. Patterns may be quickly generated; typical times ranging from a few seconds to a few minutes. In a one-dimensional arrangement, parallel layers of particles are formed. With two and three dimensional transducer arrangements, more complex particle configurations are possible since different standing-wave patterns may be generated in the resonator. Fabrication of periodic structures, such as metamaterials, having periods tunable by varying the frequency of the acoustic waves, on surfaces or in bulk volume using acoustic radiation forces, provides great flexibility in the creation of new materials. Periodicities may range from millimeters to sub-micron distances, covering a large portion of the range for optical and acoustical metamaterials.

  13. Fabrication and characterization of heterojunction transistors (United States)

    Lo, Chien-Fong


    Submircon emitter finger high-speed double heterojunction InAlAs/InGaAsSb/InGaAs bipolar transistors (DHBTs) and a variety of nitride high electron mobility transistors (HEMTs) including AlGaN/GaN, InAlN/GaN, and AlN/GaN were fabricated and characterized. DHBT structures were grown by solid source molecular beam epitaxy (SSMBE) on Fe-doped semiinsulating InP substrates and nitride HEMTs were grown with a metal organic chemical vapor deposition (MOCVD) system on sapphire or SiC substrates. AlN/GaN HEMTs were grown with a RF-VMBE on sapphire substrates. Ultra low base contact resistance of 3.7 x 10-7 ohm-cm2 after 1 min 250¢XC thermal treatment on noval InGaAsSb base of DHBTs was achieved and a long-term thermal stability of base metallization was studied. Regarding small scale DHBT fabrication, tri-layer system was introduced to improve the resolution for submicron emitter patterning and help to pile up a thicker emitter metal stack; guard-ring technique was applied around the emitter periphery in order to preserve the current gain at small emitter dimensions. Ultra low turn-on voltage and high current gain can be realized with InGaAsSb-base DHBTs as compared to the conventional InGaAs-base DHBTs. A peak current gain cutoff frequency (fT) of 268 GHz and power gain cutoff frequency (fmax) of 485 GHz were achieved. GaN-based HEMTs herein were fabricated with gate lengths from 400 nm to 1im, and were deposited Ti/Al/Ni/Au as their Ohmic contact metallization. Effects of the Ohmic contact annealing for lattice-matched InAlN/GaN HEMTs with and without a thin GaN cap layer were exhibited and their optimal annealing temperature were obtained. A maximum drain current of 1.3 A/mm and an extrinsic transconductance of 366 mS/mm were demonstrated for InAlN/GaN HEMTs with the shortest gate length. A unity-gain cutoff frequency (fT) of 69 GHz and a maximum frequency of oscillation (fmax) of 80 GHz for InAlN/GaN HEMTs were extracted from measured scattering parameters

  14. Fabrication of fluorescent chitosan-containing microcapsules

    Directory of Open Access Journals (Sweden)

    Zhang R.


    Full Text Available Intense emission peaks of Eu(DBM3Phen (DBM and Phen are dibenzoylmethane and 1,10-phenanthroline, respectively in the microcapsules containing molecules of quaternary ammonium chitosan (QACS and sodium alginate are observed. The microcapsules are assembled by using CaCO3 particles as template cores by the layer-by-layer (LbL technique. Observation of microcapsules by the fluorescence mode and the transmission mode in the confocal laser scanning microscopy shows that the microcapsules are intact after core decomposition. Fluorescence under ultraviolet irradiation comes directly from the Eu(DBM3Phen. Homogeneous assembly of Eu(DBM3Phen can be deduced due to the homogeneous fluorescence of the microcapsules in the fluorescence micrographs. The microcapsules show adherence to solid substrates due to large quantities of hydroxyl groups of QACS. AFM measurements of dried hollow microcapsules with only 4 bilayers of (CS/SA fabricated with Eu(DBM3Phen show the intact shell with a thickness of 3.0 nm. Regarding the biocompatible natural polysaccharides and the intense fluorescence emission, the microcapsules in this work might be of great importance in potential application in drug delivery and bioassay.

  15. Fabrication of Carbohydrate Microarrays by Boronate Formation. (United States)

    Adak, Avijit K; Lin, Ting-Wei; Li, Ben-Yuan; Lin, Chun-Cheng


    The interactions between soluble carbohydrates and/or surface displayed glycans and protein receptors are essential to many biological processes and cellular recognition events. Carbohydrate microarrays provide opportunities for high-throughput quantitative analysis of carbohydrate-protein interactions. Over the past decade, various techniques have been implemented for immobilizing glycans on solid surfaces in a microarray format. Herein, we describe a detailed protocol for fabricating carbohydrate microarrays that capitalizes on the intrinsic reactivity of boronic acid toward carbohydrates to form stable boronate diesters. A large variety of unprotected carbohydrates ranging in structure from simple disaccharides and trisaccharides to considerably more complex human milk and blood group (oligo)saccharides have been covalently immobilized in a single step on glass slides, which were derivatized with high-affinity boronic acid ligands. The immobilized ligands in these microarrays maintain the receptor-binding activities including those of lectins and antibodies according to the structures of their pendant carbohydrates for rapid analysis of a number of carbohydrate-recognition events within 30 h. This method facilitates the direct construction of otherwise difficult to obtain carbohydrate microarrays from underivatized glycans.

  16. Modeling electrodeposition for LIGA microdevice fabrication

    Energy Technology Data Exchange (ETDEWEB)

    Griffiths, S.K.; Nilson, R.H.; Bradshaw, R.W. [and others


    To better understand and to help optimize the electroforming portion of the LIGA process, we have developed one and two-dimensional numerical models describing electrode-position of metal into high aspect-ratio molds. The one-dimensional model addresses dissociation, diffusion, electromigration, and deposition of multiple ion species. The two-dimensional model is limited to a single species, but includes transport induced by forced flow of electrolyte outside the mold and by buoyancy associated with metal ion depletion within the mold. To guide model development and to validate these models, we have also conducted a series of laboratory experiments using a sulfamate bath to deposit nickel in cylindrical molds having aspect ratios up to twenty-five. The experimental results indicate that current densities well in excess of the diffusion-limited currents may still yield metal deposits of acceptable morphology. However, the numerical models demonstrate that such large ion fluxes cannot be sustained by convection within the mold resulting from flow across the mold top. Instead, calculations suggest that the observed enhancement of transport probably results from natural convection within the molds, and that buoyancy-driven flows may be critical to metal ion transport even in micron-scale features having very large aspect ratios. Taking advantage of this enhanced ion transport may allow order-of-magnitude reductions in electroforming times for LIGA microdevice fabrication. 42 refs., 14 figs., 1 tab.

  17. Fabricating Superhydrophobic Polymeric Materials for Biomedical Applications. (United States)

    Kaplan, Jonah; Grinstaff, Mark


    Superhydrophobic materials, with surfaces possessing permanent or metastable non-wetted states, are of interest for a number of biomedical and industrial applications. Here we describe how electrospinning or electrospraying a polymer mixture containing a biodegradable, biocompatible aliphatic polyester (e.g., polycaprolactone and poly(lactide-co-glycolide)), as the major component, doped with a hydrophobic copolymer composed of the polyester and a stearate-modified poly(glycerol carbonate) affords a superhydrophobic biomaterial. The fabrication techniques of electrospinning or electrospraying provide the enhanced surface roughness and porosity on and within the fibers or the particles, respectively. The use of a low surface energy copolymer dopant that blends with the polyester and can be stably electrospun or electrosprayed affords these superhydrophobic materials. Important parameters such as fiber size, copolymer dopant composition and/or concentration, and their effects on wettability are discussed. This combination of polymer chemistry and process engineering affords a versatile approach to develop application-specific materials using scalable techniques, which are likely generalizable to a wider class of polymers for a variety of applications.

  18. Cotation de fabrication avec les normes ISO

    CERN Document Server

    Anselmetti, Bernard


    La cotation ISO en production impose de nouvelles méthodologies pour élaborer les documents de maîtrise de la qualité géométrique des produits : les dessins de phase, du brut et d'états intermédiaires pour la conformité des pièces et les fiches de production, de réglage, de contrôle et de surveillance pour la conformité des moyens de production. Une méthode de transfert unidirectionnelle simple permet d'établir des dessins de phase en normes ISO et d'optimiser la répartition des tolérances à isocapabilité. Cette cotation est déclinée en cotation d'état intermédiaire, de production et de réglage. Une méthode tridimensionnelle est proposée pour prendre en compte les effets des défauts angulaires. Une maquette montre les fonctionnalités envisageables pour les futurs outils d'aides au tolérancement de fabrication au sein de la CFAO. De nombreux exercices illustrent les différentes démarches. Ce Manuel de tolérancement est principalement destiné aux préparateurs méthodes et aux c...

  19. Ultraprecision optical fabrication on fused silica (United States)

    Wang, Junlin


    In this paper, an optical fabrication process is introduced in detail, which is about achieving ultra-precision surface by iteration of ion beam figuring (IBF) and supersmooth polishing technology. Developed as a new technology to achieve supersmooth surface, Numerical controlled micro-jet polishing (MJP) technology is also introduced. 100mm-diameter fused silica is used as the sample. In the process, the surface is superpolished with MJP at first, then IBF is used to correct the figure, and finally MJP is applied again to finish iteration process. The path for IBF is raster scanning, and MJP processes in a spiral way. The figure and roughness of the surface are tested and analyzed with interferometer and atomic force microscope (AFM). The results indicate that ultra-precision optical surface is achieved by the iteration process with figure accuracy of 0.879nmrms, mid-spatial frequency and high-spatial frequency roughness of 0.119nmrms and 0.0726nmrms respectively.

  20. Robotic fabrication in architecture, art, and design

    CERN Document Server

    Braumann, Johannes


    Architects, artists, and designers have been fascinated by robots for many decades, from Villemard’s utopian vision of an architect building a house with robotic labor in 1910, to the design of buildings that are robots themselves, such as Archigram’s Walking City. Today, they are again approaching the topic of robotic fabrication but this time employing a different strategy: instead of utopian proposals like Archigram’s or the highly specialized robots that were used by Japan’s construction industry in the 1990s, the current focus of architectural robotics is on industrial robots. These robotic arms have six degrees of freedom and are widely used in industry, especially for automotive production lines. What makes robotic arms so interesting for the creative industry is their multi-functionality: instead of having to develop specialized machines, a multifunctional robot arm can be equipped with a wide range of end-effectors, similar to a human hand using various tools. Therefore, architectural researc...

  1. Design and fabrication of colloidal polymer nanocomposites. (United States)

    Wang, Tao; Keddie, Joseph L


    It is well established that colloidal polymer particles can be used to create organised structures by methods of horizontal deposition, vertical deposition, spin-casting, and surface pattern-assisted deposition. Each particle acts as a building block in the structure. This paper reviews how two-phase (or hybrid) polymer colloids can offer an attractive method to create nanocomposites. Structure in the composite can be controlled at the nanoscale by using such particles. Methods to create armored particles, such as via methods of hetero-flocculation and Pickering polymerization, are of particular interest here. Polymer colloids can also be blended with other types of nanoparticles, e.g. nanotubes and clay platelets, to create nanocomposites. Structure can be controlled over length scales approaching the macroscopic through the assembly of hybrid particles or particle blends via any of the various deposition methods. Colloidal nanocomposites can offer unprecedented long-range 2D or 3D order that provides a periodic modulation of physical properties. They can also be employed as porous templates for further nanomaterial fabrication. Challenges in the design and control of the macroscopic properties, especially mechanical, are considered. The importance of the internal interfacial structure (e.g. between inorganic and polymer particles) is highlighted.

  2. Fabrication and characterization of electrospun titania nanofibers

    Energy Technology Data Exchange (ETDEWEB)

    Chandrasekar, Ramya [South Dakota School of Mines and Technology; Zhang, Lifeng [ORNL; Howe, Jane Y [ORNL; Hedin, Nyle E [Department of Chemistry, South Dakota School of Mines; Zhang, Y [School of Physics and Materials Science, Anhui University, Hefei, Anhui 230039, China


    Titania (TiO2) nanofibers were fabricated by electrospinning three representative spin dopes made of titanium (IV) n-butoxide (TNBT) and polyvinylpyrrolidone (PVP) with the TNBT/PVP mass ratio being 1/2 in three solvent systems including N,N-dimethylformamide (DMF), isopropanol, and DMF/isopropanol (1/1 mass ratio) mixture, followed by pyrolysis at 500 C. The detailed morphological and structural properties of both the as-electrospun precursor nanofibers and the resulting final TiO2 nanofibers were characterized by SEM, TEM, and XRD. The results indicated that the precursor nanofibers and the final TiO2 nanofibers made from the spin dopes containing DMF alone or DMF/isopropanol mixture as the solvent had the common cylindrical morphology with diameters ranging from tens to hundreds of nanometers, while those made from the spin dope containing isopropanol alone as the solvent had an abnormal concave morphology with sizes/widths ranging from sub-microns to microns. Despite the morphological discrepancies, all precursor nanofibers were structurally amorphous without distinguishable phase separation, while all final TiO2 nanofibers consisted of anatase-phased TiO2 single-crystalline grains with sizes of approximately 10 nm. The electrospun TiO2 nanofiber mat is expected to significantly outperform other forms (such as powder and film) of TiO2 for the solar cell (particularly dye-sensitized solar cell) and photo-catalysis applications.

  3. Fabrication and characterization of branched carbon nanostructures

    Directory of Open Access Journals (Sweden)

    Sharali Malik


    Full Text Available Carbon nanotubes (CNTs have atomically smooth surfaces and tend not to form covalent bonds with composite matrix materials. Thus, it is the magnitude of the CNT/fiber interfacial strength that limits the amount of nanomechanical interlocking when using conventional CNTs to improve the structural behavior of composite materials through reinforcement. This arises from two well-known, long standing problems in this research field: (a inhomogeneous dispersion of the filler, which can lead to aggregation and (b insufficient reinforcement arising from bonding interactions between the filler and the matrix. These dispersion and reinforcement issues could be addressed by using branched multiwalled carbon nanotubes (b-MWCNTs as it is known that branched fibers can greatly enhance interfacial bonding and dispersability. Therefore, the use of b-MWCNTs would lead to improved mechanical performance and, in the case of conductive composites, improved electrical performance if the CNT filler was better dispersed and connected. This will provide major benefits to the existing commercial application of CNT-reinforced composites in electrostatic discharge materials (ESD: There would be also potential usage for energy conversion, e.g., in supercapacitors, solar cells and Li-ion batteries. However, the limited availability of b-MWCNTs has, to date, restricted their use in such technological applications. Herein, we report an inexpensive and simple method to fabricate large amounts of branched-MWCNTs, which opens the door to a multitude of possible applications.

  4. Electrospinning: a fascinating fiber fabrication technique. (United States)

    Bhardwaj, Nandana; Kundu, Subhas C


    With the emergence of nanotechnology, researchers become more interested in studying the unique properties of nanoscale materials. Electrospinning, an electrostatic fiber fabrication technique has evinced more interest and attention in recent years due to its versatility and potential for applications in diverse fields. The notable applications include in tissue engineering, biosensors, filtration, wound dressings, drug delivery, and enzyme immobilization. The nanoscale fibers are generated by the application of strong electric field on polymer solution or melt. The non-wovens nanofibrous mats produced by this technique mimics extracellular matrix components much closely as compared to the conventional techniques. The sub-micron range spun fibers produced by this process, offer various advantages like high surface area to volume ratio, tunable porosity and the ability to manipulate nanofiber composition in order to get desired properties and function. Over the years, more than 200 polymers have been electrospun for various applications and the number is still increasing gradually with time. With these in perspectives, we aim to present in this review, an overview of the electrospinning technique with its promising advantages and potential applications. We have discussed the electrospinning theory, spinnable polymers, parameters (solution and processing), which significantly affect the fiber morphology, solvent properties and melt electrospinning (alternative to solution electrospinning). Finally, we have focused on varied applications of electrospun fibers in different fields and concluded with the future prospects of this efficient technology. (c) 2010 Elsevier Inc. All rights reserved.

  5. Fabrication of protein chip by magnetic force. (United States)

    Choi, Yong-Sung; Jang, Gil-Soo; Hong, Kyung-Jin; Lee, Kyung-Sup


    This research describes a new immobilizing method of many kinds of biomaterials (enzyme, antibody, and DNA) on a transducer array using magnetic force interaction as the short-range force. The method composes two immobilizing steps. In the first step, same biomaterials are immobilized on metal particles. In the second step, the particles are arranged by the fluidic self-assembly method at random on an array. An array immobilized many kinds of the particles become multichannel biosensor. The biosensor can apply to DNA chip, protein chip, multienzyme electrode, and so on. The metal particles and the array were fabricated by micromachining manufacture. The metal particles were multilayer structure (gold, titanium, and nickel). In the array case, sidewalls of patterning nickel dots on an array were covered by thick negative photoresist (SU-8), and the array was magnetized. The array and the particles were mixed in buffer solution, and were arranged by magnetic force interaction. A quarter of total nickel dots were covered by the particles. The binding direction of the particles was controllable, and condition of particles was almost with gold surface on top. The immobilization of the biomaterials to metal particles was able to materialize it by using 3-CPD. This confirmed an activity by the luminol radiation.

  6. Material control in nuclear fuel fabrication facilities. Part I. Fuel descriptions and fabrication processes, P. O. 1236909 Final report

    Energy Technology Data Exchange (ETDEWEB)

    Borgonovi, G.M.; McCartin, T.J.; Miller, C.L.


    The report presents information on foreign nuclear fuel fabrication facilities. Fuel descriptions and fuel fabrication information for three basic reactor types are presented: The information presented for LWRs assumes that Pu--U Mixed Oxide Fuel (MOX) will be used as fuel.

  7. The effect of fabric structural parameters and fiber type on the comfort-related properties of commercial apparel fabrics

    CSIR Research Space (South Africa)

    Stoffberg, ME


    Full Text Available The effect of fabric structural parameters and fiber type on the comfort-related properties, namely water vapor resistance and thermal resistance, of commercial apparel (suiting) fabrics, containing both natural and man-made fibers have been studied...

  8. Fabrication of rectangular cross-sectional microchannels on PMMA with a CO2 laser and underwater fabricated copper mask (United States)

    Prakash, Shashi; Kumar, Subrata


    CO2 lasers are commonly used for fabricating polymer based microfluidic devices. Despite several key advantages like low cost, time effectiveness, easy to operate and no requirement of clean room facility, CO2 lasers suffer from few disadvantages like thermal bulging, improper dimensional control, difficulty to produce microchannels of other than Gaussian cross sectional shapes and inclined surface walls. Many microfluidic devices require square or rectangular cross-sections which are difficult to produce using normal CO2 laser procedures. In this work, a thin copper sheet of 40 μm was used as a mask above the PMMA (Polymethyl-methacrylate) substrate while fabricating the microchannels utilizing the raster scanning feature of the CO2 lasers. Microchannels with different width dimensions were fabricated utilizing a CO2 laser in with mask and without-mask conditions. A comparison of both the fabricating process has been made. It was found that microchannels with U shape cross section and rectangular cross-section can efficiently be produced using the with mask technique. In addition to this, this technique can provide perfect dimensional control and better surface quality of the microchannel walls. Such a microchannel fabrication process do not require any post-processing. The fabrication of mask using a nanosecond fiber laser has been discussed in details. An underwater laser fabrication method was adopted to overcome heat related defects in mask preparation. Overall, the technique was found to be easy to adopt and significant improvements were observed in microchannel fabrication.

  9. Development of Fabrication Technology for Ceramic Nuclear Fuel

    Energy Technology Data Exchange (ETDEWEB)

    Kim, H. S.; Lee, Y. W.; Na, S. H.; Kim, Y. G.; Jung, C. Y.; Kim, S. H.; Lee, S. C.; Son, D. S


    Purpose and Necessity Research purposes for the 3rd stage were to reaffirm the MOX fabrication processes and to establish the process database, based on the fabrication technology developed during the previous stage. This project was also proceeded to improve the fuel performance and to accomplish the inherent MOX technology for PWR. The fabrication processes should be proceeded in the glove boxes because the raw powders of MOX fuel is very toxic. Therefore, some special technology were needed to develop besides the fuel fabrication technology. Both core technology and steadiness of fabrication process are important to obtain homogeneity and thermo-physical properties of MOX fuel pellet. By developing these technology in fashion unique to ourselves, we can take the initiative in the nuclear fuel for next generation. The uranium price has been increasing along with the oil price recently. We have to secure the MOX fabrication technology which serves the effective use of uranium resource. Improvement of pellet characteristics along with the MOX irradiation analysis: Collection and monitoring of the MOX irradiation data, Establishment of the improvement methods of pellet characteristics Establishment of the MOX pellet fabrication process by the unique technology, Establishment of database with the MOX fabrication parameters and characteristics, Analysis of co-relation and re-appearance of the pellet characteristics affected by each process parameter, Construction of feedback system between database and process, Application of the unique fabrication technology to the industrial spot. Applicability of the unique fabrication processes to the glove box technology, Installment of process equipment in the glove box and development of operation skill, Methods for modifying, handling, maintaining and fixing of glove box and subsidiary, Construction of transport channel for the connection between glove boxes - MOX fabrication by the unique technology in the glove box. Research

  10. Investigation on mechanical properties of basalt composite fabrics (experiment study

    Directory of Open Access Journals (Sweden)

    Talebi Mazraehshahi H.


    Full Text Available To fully appreciate the role and application of composite materials to structures, correct understanding of mechanical behaviors required for selection of optimum material. Fabric reinforced composites are composed of a matrix that is reinforced with pliable fabric, glass fabric is most popular reinforcement for different application specially in aircraft structure, although other fabric material are also used. At this study new fabric material called basalt with epoxy resin introduced and mechanical behaviors of this material investigated from view point of testing. For this study two type of fabric with different thickness used. Comparison between this composite reinforcement with popular reinforcement as carbon, glass, kevlar performed. To determine mechanical properties of epoxy based basalt fabric following test procedure performed : 1. Tensile testing according to ASTM D3039 in 0° and 90° direction to find ultimate strength in tension and shear, modulus of elasticity, elangation and ultimate strain. 2. Compression testing according to EN 2850 ultimate compression strength and maximum deformation under compression loading. 3. Shear testing according to ASTM D3518-94 to find in plane shear response of polymer matrix composites materials. 4. Predict flexural properties of sandwich construction which manufactured from basalt facing with PVC foam core according to ASTM C393-94. Material strength properties must be based on enough tests of material to meet the test procedure specifications [1]. For this reason six specimens were manufactured for testing and the tests were performed on them using an INSTRON machine model 5582. In the study, the effect of percent of resin in basalt reinforced composite was investigated. Also the weights of the ballast based composites with different percent of resin were measured with conventional composites. As the weight is an important parameter in aerospace industry when the designer wants to replace one

  11. Investigation on mechanical properties of basalt composite fabrics (experiment study) (United States)

    Talebi Mazraehshahi, H.; Zamani, H.


    To fully appreciate the role and application of composite materials to structures, correct understanding of mechanical behaviors required for selection of optimum material. Fabric reinforced composites are composed of a matrix that is reinforced with pliable fabric, glass fabric is most popular reinforcement for different application specially in aircraft structure, although other fabric material are also used. At this study new fabric material called basalt with epoxy resin introduced and mechanical behaviors of this material investigated from view point of testing. For this study two type of fabric with different thickness used. Comparison between this composite reinforcement with popular reinforcement as carbon, glass, kevlar performed. To determine mechanical properties of epoxy based basalt fabric following test procedure performed : 1). Tensile testing according to ASTM D3039 in 0° and 90° direction to find ultimate strength in tension and shear, modulus of elasticity, elangation and ultimate strain. 2). Compression testing according to EN 2850 ultimate compression strength and maximum deformation under compression loading. 3). Shear testing according to ASTM D3518-94 to find in plane shear response of polymer matrix composites materials. 4). Predict flexural properties of sandwich construction which manufactured from basalt facing with PVC foam core according to ASTM C393-94. Material strength properties must be based on enough tests of material to meet the test procedure specifications [1]. For this reason six specimens were manufactured for testing and the tests were performed on them using an INSTRON machine model 5582. In the study, the effect of percent of resin in basalt reinforced composite was investigated. Also the weights of the ballast based composites with different percent of resin were measured with conventional composites. As the weight is an important parameter in aerospace industry when the designer wants to replace one material with

  12. Interpreting inverse magnetic fabric in dikes from Eastern Iceland (United States)

    Trippanera, Daniele; Urbani, Stefano; Porreca, Massimiliano; Acocella, Valerio; Kissel, Catherine; Sagnotti, Leonardo; Winkler, Aldo


    Since the 70's magnetic fabric analysis has been used to infer magma emplacement in dikes. However, the interpretation of magmatic flow orientation in dikes is often complicated by the occurrence of anomalous (i.e. inverse) magnetic fabric. This latter may either reflect the presence of single-domain (SD) grains or result from peculiar orientation mechanisms of magnetic minerals in magmas of different viscosities. Tertiary dike swarms of extinct volcanic systems in Eastern Iceland represent the ideal case study to clarify the origin of anomalous magnetic fabric. Here we present the results of a multidisciplinary study on dikes belonging to the Alftafjordur volcanic system (Eastern Iceland), including a: (1) structural field study in order to identify kinematic and thermal indicators of dikes; (2) anisotropy of low-field magnetic susceptibility (AMS) analysis, to investigate the magnetic fabric and reconstruct the flow direction of 25 dikes; (3) first order reversal curve (FORC) diagrams and thermomagnetic properties of selected dikes to define the magnetic mineralogy; (4) petrofabric and image analyses at different microscopic scales to investigate the origin of the magnetic fabric and compare the AMS results with mineral texture. Our results show that half of the dikes show a well defined inverse magnetic fabrics (k max orthogonal to the dike margins) and anomalous high anisotropy degrees. Only 7 dikes have a normal magnetic fabric and other 6 dikes have an intermediate magnetic fabric. No clear prevalence of SD grains, which could explain the inverse magnetic fabric, was observed. On the contrary, petrofabric and thermomagnetic analysis reveal the presence of low Ti-content coarse magnetite and high Ti-content elongated magnetite grains as the main contributors to most of the observed magnetic fabrics. In particular, the orientation of the elongated high Ti-content magnetite grains, though usually scattered, is partly comparable with that of the maximum and


    Directory of Open Access Journals (Sweden)

    ORK Nilay


    Full Text Available Product variability of manufactured leather goods such as garment leathers could be closely related to the wear comfort because each material forming the garments are affected the comfort properties of the products. Considering the significant demand to elastic woven stretch fabrics and the advantages provided to leather goods like allowing easy body movements, well-fitting and keeping the shape make the use of stretch fabrics focus in interest. In this study, the performance properties of stretch leathers, leathers and spandex fabrics were presented and the differences between the characteristic properties of the leathers were described. For this purpose, physical characteristics of leathers were investigated in terms of thickness, weight, drape ability, stiffness, bending stiffness, air and water vapor permeability. The drape ability, stiffness and bending stiffness properties were significantly affected by the stretch fabrics laminated on the suede side of the leathers. The drape ability, stiffness and bending values were increased due to the implementation of stretch fabrics. There was no significant difference between the air permeability values of the leathers prior and after the implementation of stretch fabrics in contrast to water vapor permeability. The results of this study showed that the aesthetic behavior of clothing materials such as drape and stiffness properties as well as water vapor permeability was mainly affected from the implementation of the stretch fabrics.

  14. Weaves and Colours of Lithuanian Folk Skirts Fabrics

    Directory of Open Access Journals (Sweden)



    Full Text Available In the article weaves and colours of Lithuanian folk skirts fabrics are analysed. The investigation objects are the skirts from funds of three Lithuanian Museums: 258 skirts from National M. K. Čiurlionis Museum of Art, 85 skirts from Lithuanian Open Air Museum and 16 skirts from A. and A. Tamošaitis gallery “Židinys”. Distribution of skirts fabrics according to weaves was estimated, and it shows, that fabrics of plain weave are most widespread (53 %, combined and twill weaves are less popular (19 % and 18 %, respectively. The weaves of fabrics are determined during investigation and plans of weave were made proposing recommendations for manufacturing of similar fabrics. Also distribution of colours and number of colours in the fabrics were analysed. The biggest number of colours is in fabrics of simple weaves (plain and twill, and the most characteristic are green, red, black and blue colours. DOI:

  15. Weaves and Colours of Lithuanian Folk Skirts Fabrics

    Directory of Open Access Journals (Sweden)



    Full Text Available In the article weaves and colours of Lithuanian folk skirts fabrics are analysed. The investigation objects are the skirts from funds of three Lithuanian Museums: 258 skirts from National M. K. Čiurlionis Museum of Art, 85 skirts from Lithuanian Open Air Museum and 16 skirts from A. and A. Tamošaitis gallery “Židinys”. Distribution of skirts fabrics according to weaves was estimated, and it shows, that fabrics of plain weave are most widespread (53 %, combined and twill weaves are less popular (19 % and 18 %, respectively. The weaves of fabrics are determined during investigation and plans of weave were made proposing recommendations for manufacturing of similar fabrics. Also distribution of colours and number of colours in the fabrics were analysed. The biggest number of colours is in fabrics of simple weaves (plain and twill, and the most characteristic are green, red, black and blue colours. DOI:

  16. Multifunctional non-woven fabrics of interfused graphene fibres (United States)

    Li, Zheng; Xu, Zhen; Liu, Yingjun; Wang, Ran; Gao, Chao


    Carbon-based fibres hold promise for preparing multifunctional fabrics with electrical conductivity, thermal conductivity, permeability, flexibility and lightweight. However, these fabrics are of limited performance mainly because of the weak interaction between fibres. Here we report non-woven graphene fibre fabrics composed of randomly oriented and interfused graphene fibres with strong interfibre bonding. The all-graphene fabrics obtained through a wet-fusing assembly approach are porous and lightweight, showing high in-plane electrical conductivity up to ∼2.8 × 104 S m−1 and prominent thermal conductivity of ∼301.5 W m−1 K−1. Given the low density (0.22 g cm−3), their specific electrical and thermal conductivities set new records for carbon-based papers/fabrics and even surpass those of individual graphene fibres. The as-prepared fabrics are further used as ultrafast responding electrothermal heaters and durable oil-adsorbing felts, demonstrating their great potential as high-performance and multifunctional fabrics in real-world applications. PMID:27901022

  17. Strategies for the fabrication of porous platinum electrodes

    Energy Technology Data Exchange (ETDEWEB)

    Kloke, Arne; Stetten, Felix von; Kerzenmacher, Sven [Laboratory for MEMS Applications, Department of Microsystems Engineering-IMTEK, University of Freiburg, Freiburg (Germany); Zengerle, Roland [Laboratory for MEMS Applications, Department of Microsystems Engineering-IMTEK, University of Freiburg, Freiburg (Germany); BIOSS Centre for Biological Signalling Studies, Albert-Ludwigs-Universitaet Freiburg (Germany)


    Porous platinum is of high technological importance due to its various applications in fuel cells, sensors, stimulation electrodes, mechanical actuators and catalysis in general. Based on a discussion of the general principles behind the reduction of platinum salts and corresponding deposition processes this article discusses techniques available for platinum electrode fabrication. The numerous, different strategies available to fabricate platinum electrodes are reviewed and discussed in the context of their tuning parameters, strengths and weaknesses. These strategies comprise bottom-up approaches as well as top-down approaches. In bottom-up approaches nanoparticles are synthesized in a first step by chemical, photochemical or sonochemical means followed by an electrode formation step by e.g. thin film technology or network formation to create a contiguous and conducting solid electrode structure. In top-down approaches fabrication starts with an already conductive electrode substrate. Corresponding strategies enable the fabrication of substrate-based electrodes by e.g. electrodeposition or the fabrication of self-supporting electrodes by dealloying. As a further top-down strategy, this review describes methods to decorate porous metals other than platinum with a surface layer of platinum. This way, fabrication methods not performable with platinum can be applied to the fabrication of platinum electrodes with the special benefit of low platinum consumption. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  18. Multifunctional non-woven fabrics of interfused graphene fibres (United States)

    Li, Zheng; Xu, Zhen; Liu, Yingjun; Wang, Ran; Gao, Chao


    Carbon-based fibres hold promise for preparing multifunctional fabrics with electrical conductivity, thermal conductivity, permeability, flexibility and lightweight. However, these fabrics are of limited performance mainly because of the weak interaction between fibres. Here we report non-woven graphene fibre fabrics composed of randomly oriented and interfused graphene fibres with strong interfibre bonding. The all-graphene fabrics obtained through a wet-fusing assembly approach are porous and lightweight, showing high in-plane electrical conductivity up to ~2.8 × 104 S m-1 and prominent thermal conductivity of ~301.5 W m-1 K-1. Given the low density (0.22 g cm-3), their specific electrical and thermal conductivities set new records for carbon-based papers/fabrics and even surpass those of individual graphene fibres. The as-prepared fabrics are further used as ultrafast responding electrothermal heaters and durable oil-adsorbing felts, demonstrating their great potential as high-performance and multifunctional fabrics in real-world applications.


    Directory of Open Access Journals (Sweden)

    DIRLIK UYSAL Çagla Dilara


    Full Text Available Knitting fabrics are characterized by the confort they confer on the wearer. Textiles with mcirocpsules are bocoming more popular and nowadays Phase Change Materials (PCM are used for thermal control and to avoid temperature changes to be clearly noticeable. Consequently, they can control variations in temerpature and make the user feel more confortable. Washing durability and rigidity are very important when considering fabrics treated with microencapsules. In this study we first aimed to study what influence has the resin concentration with the durability of microencapsules on the fabric after having washed it and its confort. To observe the presence of microcapsules after washing procedure the scanning electron microscopy (SEM was used. SEM analysis showed different density of microcapsules with PCMs depending on the binder concentration used. It could be clearly noticieable that 5times washed fabric and 10times washed fabric still show microacapsules on it. On the other hand we used padding method for the application of PCMs into the fabris and this study put forth the binder effect on rigidity. We have demonstrated that when we increase the binder concentration for padding bath, after 10th laundry cycles for the same fabric, we still have microcalsules on it. On the other hand, density of binder effect negatively influences on rigidity of the fabric.

  20. Flame-resistant pure and hybrid woven fabrics from basalt (United States)

    Jamshaid, H.; Mishra, R.; Militky, J.


    This work has been formulated to investigate the burning behavior of different type of fabrics. The main concentration is to see how long the fabric resists after it catches the fire and the propagation of fire can be reduced by using flame resistant fiber i.e basalt. Basalt fiber is an environmental friendly material with low input, high output, low energy consumption and less emission. The goal of present investigations is to show the dependence of fabric flammability on its structure parameters i.e weave type, blend type etc. Fabric weaves have strong effect on flammability properties. Plain weave has the lowest burning rate as the density of the plain weave fabric is more and the structure is tight which gives less chances of flame passing through the fabric. Thermal stability is evaluated with TGA of all hybrid and nonhybrid fabrics and compared. The thermal stability of the basalt fiber is excellent. When comparing thermal analysis curves for hybrid samples it demonstrates that thermal stability of the samples containing basalt is much higher than the non- hybrid samples. Percentage weight loss is less in hybrid samples as compared to non-hybrid samples. The effectiveness of hybridization on samples may be indicated by substantial lowering of the decomposition mass. Correlation was made between flammability with the infrared radiations (IR)