Magnetic refrigerator for hydrogen liquefaction

Energy Technology Data Exchange (ETDEWEB)

Numazawa, T [National Institute for Materials Science, Tsukuba (Japan); Kamlya, K. [Japan Atomic Energy Agency, Naka (Japan); Utaki, T. [Osaka University, Osaka (Japan); Matsumoto, K. [Kanazawa University, Kanazawa (Japan)

2013-06-15

This paper reviews the development status of magnetic refrigeration system for hydrogen liquefaction. There is no doubt that hydrogen is one of most important energy sources in the near future. In particular, liquid hydrogen can be utilized for infrastructure construction consisting of storage and transportation. Liquid hydrogen is in cryogenic temperatures and therefore high efficient liquefaction method must be studied. Magnetic refrigeration which uses the magneto-caloric effect has potential to realize not only the higher liquefaction efficiency > 50 %, but also to be environmentally friendly and cost effective. Our hydrogen magnetic refrigeration system consists of Carnot cycle for liquefaction stage and AMR (active magnetic regenerator) cycle for precooling stages. For the Carnot cycle, we develop the high efficient system > 80 % liquefaction efficiency by using the heat pipe. For the AMR cycle, we studied two kinds of displacer systems, which transferred the working fluid. We confirmed the AMR effect with the cooling temperature span of 12 K for 1.8 T of the magnetic field and 6 second of the cycle. By using the simulation, we estimate the total efficiency of the hydrogen liquefaction plant for 10 kg/day. A FOM of 0.47 is obtained in the magnetic refrigeration system operation temperature between 20 K and 77 K including LN2 work input.

Effect of Recycle Solvent Hydrotreatment on Oil Yield of Direct Coal Liquefaction

Directory of Open Access Journals (Sweden)

Shansong Gao

2015-07-01

Full Text Available Effects of the recycle solvent hydrotreatment on oil yield of direct coal liquefaction were carried out in the 0.18 t/day direct coal liquefaction bench support unit of National Engineering Laboratory for Direct Coal Liquefaction (China. Results showed that the hydrogen-donating ability of the hydrogenated recycle solvent improved and the hydrogen consumption of solvent hydrotreatment was increased by decreasing liquid hourly space velocity (LHSV from 1.5 to 1.0 h−1 and increasing reaction pressure from 13.7 to 19.0 MPa. The hydrogen-donating ability of the hydrogenated recycle solvent was enhanced, thus promoting the oil yield and coal conversion of the liquefaction reaction. The coal conversion and distillates yield of coal liquefaction were increased from 88.74% to 88.82% and from 47.41% to 49.10%, respectively, with the increase in the solvent hydrotreatment pressure from 13.7 to 19.0 MPa. The coal conversion and distillates of coal liquefaction were increased from 88.82% to 89.27% and from 49.10% to 54.49%, respectively, when the LHSV decreased from 1.5 to 1.0 h−1 under the solvent hydrotreatment pressure of 19.0 MPa.

Sequential high gravity ethanol fermentation and anaerobic digestion of steam explosion and organosolv pretreated corn stover.

Science.gov (United States)

Katsimpouras, Constantinos; Zacharopoulou, Maria; Matsakas, Leonidas; Rova, Ulrika; Christakopoulos, Paul; Topakas, Evangelos

2017-11-01

The present work investigates the suitability of pretreated corn stover (CS) to serve as feedstock for high gravity (HG) ethanol production at solids-content of 24wt%. Steam explosion, with and without the addition of H 2 SO 4 , and organosolv pretreated CS samples underwent a liquefaction/saccharification step followed by simultaneous saccharification and fermentation (SSF). Maximum ethanol concentration of ca. 76g/L (78.3% ethanol yield) was obtained from steam exploded CS (SECS) with 0.2% H 2 SO 4 . Organosolv pretreated CS (OCS) also resulted in high ethanol concentration of ca. 65g/L (62.3% ethanol yield). Moreover, methane production through anaerobic digestion (AD) was conducted from fermentation residues and resulted in maximum methane yields of ca. 120 and 69mL/g volatile solids (VS) for SECS and OCS samples, respectively. The results indicated that the implementation of a liquefaction/saccharification step before SSF employing a liquefaction reactor seemed to handle HG conditions adequately. Copyright © 2017 Elsevier Ltd. All rights reserved.

Liquefaction of uranium tailings

International Nuclear Information System (INIS)

1992-02-01

Numerical methods for assessing the liquefaction potential of soils are reviewed with a view to their application to uranium tailings. The method can be divided into two categories: total stress analysis, where changes in pore pressure are not considered in the soil model, and effective stress analysis, where changes in pore pressure are included in the soil model. Effective stress analysis is more realistic, but few computer programs exist for such analysis in two or three dimensions. A simple linearized, two-dimensional, finite element effective stress analysis which incorporates volumetric compaction due to shear motion is described and implemented. The new program is applied to the assessment of liquefaction potential of tailings in the Quirke Mine tailings area near Elliot Lake, Ontario. The results are compared with those of a total stress analysis. Both analyses indicate liquefaction would occur if a magnitude 6.0 earthquake were to occur near the area. However, the extent of liquefaction predicted by the effective stress analysis is much less than that predicted by the total stress analysis. The results of both methods are sensitive to assumed material properties and to the method used to determine the cyclic shear strength of the tailings. Further analysis, incorporating more in situ and/or laboratory data, is recommended before conclusions can be made concerning the dynamic stability of these tailings

Fiscal 1994 report. Liquefaction key technology subcommittee; 1994 nendo ekika kiban gijutsu bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The subcommittee held the 1st meeting in August 1994 and the 2nd in March 1995, when preceding fiscal year's research results, fiscal 1994 research plans, fiscal 1994 research results, etc., were introduced, and deliberated. In the study of hydrorefining of naphtha, kerosene, and light oil fractions, a nitrogen concentration level of not more than 5 ppm was achieved by refining oils from Indonesian coal. Studies were also made about the two-step hydrorefining system, the relationship between the coal oil refining level and sludge formation, etc. In the research for the development of novel catalysts for upgrading coal oil, the active life of a nickel-supporting catalyst for hydrogenation at the 1st step was somewhat prolonged with an increase in the amount of nickel. In the study of coal liquefaction conditions, an AWIP method was deliberated, wherein liquefaction process waste water was utilized as one of catalytic component adjusting materials. For upgrading liquefaction key technologies, studies were made for catalyst improvement and pretreatment method development, and about the behavior of liquefaction reaction in a high boiling solvent-aided process. (NEDO)

Comparative study on liquefaction of creosote and chromated copper arsenate (CCA)-treated wood and untreated southern pine wood: effects of acid catalyst content, liquefaction time, temperature, and phenol to wood ratio

Science.gov (United States)

Hui Pan; Chung-Yun Hse; Todd F. Shupe

2009-01-01

Creosote- and chromated copper arsenate (CCA)-treated wood waste and untreated southern pine wood were liquefied with phenol and sulfuric acid. The effects of sulfuric acid content, liquefaction time, liquefaction temperature, and phenol to wood ratio on liquefaction rate (i.e., wood residue content) were investigated and analyzed by analysis of variance (...

Characterisation of Liquefaction Effects for Beyond-Design Basis Safety Assessment of Nuclear Power Plants

Science.gov (United States)

Bán, Zoltán; Győri, Erzsébet; János Katona, Tamás; Tóth, László

2015-04-01

Preparedness of nuclear power plants to beyond design base external effects became high importance after 11th of March 2011 Great Tohoku Earthquakes. In case of some nuclear power plants constructed at the soft soil sites, liquefaction should be considered as a beyond design basis hazard. The consequences of liquefaction have to be analysed with the aim of definition of post-event plant condition, identification of plant vulnerabilities and planning the necessary measures for accident management. In the paper, the methodology of the analysis of liquefaction effects for nuclear power plants is outlined. The case of Nuclear Power Plant at Paks, Hungary is used as an example for demonstration of practical importance of the presented results and considerations. Contrary to the design, conservatism of the methodology for the evaluation of beyond design basis liquefaction effects for an operating plant has to be limited to a reasonable level. Consequently, applicability of all existing methods has to be considered for the best estimation. The adequacy and conclusiveness of the results is mainly limited by the epistemic uncertainty of the methods used for liquefaction hazard definition and definition of engineering parameters characterizing the consequences of liquefaction. The methods have to comply with controversial requirements. They have to be consistent and widely accepted and used in the practice. They have to be based on the comprehensive database. They have to provide basis for the evaluation of dominating engineering parameters that control the post-liquefaction response of the plant structures. Experience of Kashiwazaki-Kariwa plant hit by Niigata-ken Chuetsu-oki earthquake of 16 July 2007 and analysis of site conditions and plant layout at Paks plant have shown that the differential settlement is found to be the dominating effect in case considered. They have to be based on the probabilistic seismic hazard assessment and allow the integration into logic

Hydrothermal Liquefaction of Enzymatic Hydrolysis Lignin: Biomass Pretreatment Severity Affects Lignin Valorization

DEFF Research Database (Denmark)

Jensen, Mads M.; Djajadi, Demi T.; Torri, Cristian

2018-01-01

Alkalinehydrothermal liquefaction (HTL) of lignin-rich enzymatichydrolysis residues (EnzHR) from wheat straw and Miscanthusx giganteus was performed at 255, 300, and 345 °C to investigate valorization of this side-stream from second-generation bioethanol production. The EnzHR were from biomass...... contributed with additional chemical information as well as confirming trends seen from quantified monomers. This work is relevant for future lignin valorization in biorefineries based on current second-generation bioethanol production....

Fiscal 1990 report on the bituminous coal liquefaction section meeting; 1990 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1991-03-01

At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are delivered and discussions are made concerning the progress of research and development activities. Reported and discussed in relation to the pilot plant support research, etc., are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); development of an optimum coal refining technique (Sumitomo Coal Mining Co., Ltd.); development of an optimum pretreatment technique and improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.); and studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.). Reported and discussed in relation to researches using a bituminous coal liquefaction pilot plant are the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.), the latter covering liquefaction solvent performance optimization, slurry pre-heating furnaces, coal slurry properties, and so forth. (NEDO)

Effects of relative density and accumulated shear strain on post-liquefaction residual deformation

Directory of Open Access Journals (Sweden)

J. Kim

2013-10-01

Full Text Available The damage caused by liquefaction, which occurs following an earthquake, is usually because of settlement and lateral spreading. Generally, the evaluation of liquefaction has been centered on settlement, that is, residual volumetric strain. However, in actual soil, residual shear and residual volumetric deformations occur simultaneously after an earthquake. Therefore, the simultaneous evaluation of the two phenomena and the clarification of their relationship are likely to evaluate post-liquefaction soil behaviors more accurately. Hence, a quantitative evaluation of post-liquefaction damage will also be possible. In this study, the effects of relative density and accumulated shear strain on post-liquefaction residual deformations were reviewed through a series of lateral constrained-control hollow cylindrical torsion tests under undrained conditions. In order to identify the relationship between residual shear and residual volumetric strains, this study proposed a new test method that integrates monotonic loading after cyclic loading, and K0-drain after cyclic loading – in other words, the combination of cyclic loading, monotonic loading, and the K0 drain. In addition, a control that maintained the lateral constrained condition across all the processes of consolidation, cyclic loading, monotonic loading, and drainage was used to reproduce the anisotropy of in situ ground. This lateral constrain control was performed by controlling the axial strain, based on the assumption that under undrained conditions, axial and lateral strains occur simultaneously, and unless axial strain occurs, lateral strain does not occur. The test results confirmed that the recovery of effective stresses, which occur during monotonic loading and drainage after cyclic loading, respectively, result from mutually different structural restoration characteristics. In addition, in the ranges of 40–60% relative density and 50–100% accumulated shear strain, relative

Improvements on mapping soil liquefaction at a regional scale

Science.gov (United States)

Zhu, Jing

Earthquake induced soil liquefaction is an important secondary hazard during earthquakes and can lead to significant damage to infrastructure. Mapping liquefaction hazard is important in both planning for earthquake events and guiding relief efforts by positioning resources once the events have occurred. This dissertation addresses two aspects of liquefaction hazard mapping at a regional scale including 1) predictive liquefaction hazard mapping and 2) post-liquefaction cataloging. First, current predictive hazard liquefaction mapping relies on detailed geologic maps and geotechnical data, which are not always available in at-risk regions. This dissertation improves the predictive liquefaction hazard mapping by the development and validation of geospatial liquefaction models (Chapter 2 and 3) that predict liquefaction extent and are appropriate for global application. The geospatial liquefaction models are developed using logistic regression from a liquefaction database consisting of the data from 27 earthquake events from six countries. The model that performs best over the entire dataset includes peak ground velocity (PGV), VS30, distance to river, distance to coast, and precipitation. The model that performs best over the noncoastal dataset includes PGV, VS30, water table depth, distance to water body, and precipitation. Second, post-earthquake liquefaction cataloging historically relies on field investigation that is often limited by time and expense, and therefore results in limited and incomplete liquefaction inventories. This dissertation improves the post-earthquake cataloging by the development and validation of a remote sensing-based method that can be quickly applied over a broad region after an earthquake and provide a detailed map of liquefaction surface effects (Chapter 4). Our method uses the optical satellite images before and after an earthquake event from the WorldView-2 satellite with 2 m spatial resolution and eight spectral bands. Our method

Behaviors of rice straw two-step liquefaction with sub/supercritical ethanol in carbon dioxide atmosphere.

Science.gov (United States)

Yang, Tianhua; Wang, Jian; Li, Bingshuo; Kai, Xingping; Xing, Wanli; Li, Rundong

2018-06-01

This study extended previous work investigating two-step liquefaction by supercritical ethanol of rice straw under CO 2 atmosphere at temperatures of 270-345 °C. Subcritical CO 2 -subcritical ethanol (SubCO 2 -SubEtOH) pretreatment decreased the content of lignin in the rice stalk from 22.94 to 21.43 wt%. The results showed that although oxygen-transfer reaction, transesterification, carbonylation, and other reactions may occur with the supercritical CO 2 -supercritical ethanol (ScCO 2 -ScEtOH) liquefaction reactions, transesterification was the main reaction. The "de-oxygen-transfer" reaction mainly comprised de-oxygenation and decarboxylation. For temperatures exceeding 320 °C, the bio-oil yield decreased because the effects of esters decreased. The residence time affected the H/C and O/C ratios to a minor extent. It was shown that the nucleophilic and hydrolytic functions of ethanol might be strengthened, generating higher amounts of ester, phenolic, acidic, and hydrocarbon derivatives in the bio-oil fraction. Copyright © 2018 Elsevier Ltd. All rights reserved.

Probabilistic and Scenario Seismic and Liquefaction Hazard Analysis of the Mississippi Embayment Incorporating Nonlinear Site Effects

Science.gov (United States)

Cramer, C. H.; Dhar, M. S.

2017-12-01

The influence of deep sediment deposits of the Mississippi Embayment (ME) on the propagation of seismic waves is poorly understood and remains a major source of uncertainty for site response analysis. Many researchers have studied the effects of these deposits on seismic hazard of the area using available information at the time. In this study, we have used updated and newly available resources for seismic and liquefaction hazard analyses of the ME. We have developed an improved 3D geological model. Additionally, we used surface geological maps from Cupples and Van Arsdale (2013) to prepare liquefaction hazard maps. Both equivalent linear and nonlinear site response codes were used to develop site amplification distributions for use in generating hazard maps. The site amplification distributions are created using the Monte Carlo approach of Cramer et al. (2004, 2006) on a 0.1-degree grid. The 2014 National Seismic Hazard model and attenuation relations (Petersen et al., 2014) are used to prepare seismic hazard maps. Then liquefaction hazard maps are generated using liquefaction probability curves from Holzer (2011) and Cramer et al. (2015). Equivalent linear response (w/ increased precision, restricted nonlinear behavior with depth) shows similar hazard for the ME compared to nonlinear analysis (w/o pore pressure) results. At short periods nonlinear deamplification dominates the hazard, but at long periods resonance amplification dominates. The liquefaction hazard tends to be high in Holocene and late Pleistocene lowland sediments, even with lowered ground water levels, and low in Pleistocene loess of the uplands. Considering pore pressure effects in nonlinear site response analysis at a test site on the lowlands shows amplification of ground motion at short periods. PGA estimates from ME liquefaction and MMI observations are in the 0.25 to 0.4 g range. Our estimated M7.5 PGA hazard within 10 km of the fault can exceed this. Ground motion observations from

Residual Liquefaction under Standing Waves

DEFF Research Database (Denmark)

Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

2012-01-01

This paper summarizes the results of an experimental study which deals with the residual liquefaction of seabed under standing waves. It is shown that the seabed liquefaction under standing waves, although qualitatively similar, exhibits features different from that caused by progressive waves....... The experimental results show that the buildup of pore-water pressure and the resulting liquefaction first starts at the nodal section and spreads towards the antinodal section. The number of waves to cause liquefaction at the nodal section appears to be equal to that experienced in progressive waves for the same...

Dispersed-phase catalysis in coal liquefaction

International Nuclear Information System (INIS)

Utz, B.R.; Cugini, A.V.; Frommell, E.A.

1990-01-01

This paper reports that the specific reaction (activation) conditions for the conversion of catalyst precursors to unsupported catalyst have a direct effect on the catalytic activity and dispersion. The importance of reaction intermediates in decomposition of ammonium heptamolybdate and ammonium tetrathiomolybdate, and the sensitivity of these intermediates to reaction conditions, were studied in coal liquefaction systems. Recent results indicate that optimization of activation conditions facilitates the formation of a highly dispersed and active form of molybdenum disulfide for coal liquefaction. The use of the catalyst precursors ammonium heptamolybdate, ammonium tetrathiomolybdate, and molybdenum trisulfide for the conversion of coal to soluble products will be discussed. The use of an unsupported dispersed-phase catalyst for direct coal liquefaction is not a novel concept and has been employed in may studies with varying success. Dispersed-phase catalysts soluble and oil-soluble salts, and as finely divided powders. While some methods of catalyst introduction give higher dispersion of the catalyst and greater activity for the liquefaction of coal, all of the techniques allow the formation of a finely dispersed inorganic phase

Advanced direct liquefaction concepts for PETC generic units. Final report, Phase I

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The Advanced Concepts for Direct Coal Liquefaction program was initiated by the Department of Energy in 1991 to develop technologies that could significantly reduce the cost of producing liquid fuels by the direct liquefaction of coal. The advanced 2-stage liquefaction technology that was developed at Wilsonville over the past 10 years has contributed significantly toward decreasing the cost of producing liquids from coal to about $33/bbl. It remains, however, the objective of DOE to further reduce this cost to a level more competitive with petroleum based products. This project, among others, was initiated to investigate various alternative approaches to develop technologies that might ultimately lead to a 25 % reduction in cost of product. In this project a number of novel concepts were investigated, either individually or in a coupled configuration that had the potential to contribute toward meeting the DOE goal. The concepts included mature technologies or ones closely related to them, such as coal cleaning by oil agglomeration, fluid coking and distillate hydrotreating and dewaxing. Other approaches that were either embryonic or less developed were chemical pretreatment of coal to remove oxygen, and dispersed catalyst development for application in the 2-stage liquefaction process. This report presents the results of this project. It is arranged in four sections which were prepared by participating organizations responsible for that phase of the project. A summary of the overall project and the principal results are given in this section. First, however, an overview of the process economics and the process concepts that were developed during the course of this program is presented.

Hydrothermal liquefaction of biomass

DEFF Research Database (Denmark)

Toor, Saqib; Rosendahl, Lasse; Rudolf, Andreas

2011-01-01

This article reviews the hydrothermal liquefaction of biomass with the aim of describing the current status of the technology. Hydrothermal liquefaction is a medium-temperature, high-pressure thermochemical process, which produces a liquid product, often called bio-oil or bi-crude. During...... the hydrothermal liquefaction process, the macromolecules of the biomass are first hydrolyzed and/or degraded into smaller molecules. Many of the produced molecules are unstable and reactive and can recombine into larger ones. During this process, a substantial part of the oxygen in the biomass is removed...... by dehydration or decarboxylation. The chemical properties of bio-oil are highly dependent of the biomass substrate composition. Biomass constitutes of various components such as protein; carbohydrates, lignin and fat, and each of them produce distinct spectra of compounds during hydrothermal liquefaction...

Pretreatment methods to obtain pumpable high solid loading wood–water slurries for continuous hydrothermal liquefaction systems

DEFF Research Database (Denmark)

Dãrãbana, Iulia-Maria; Rosendahl, Lasse Aistrup; Pedersen, Thomas Helmer

2015-01-01

Feedstock pretreatment is a prerequisite step for continuous processing of lignocellulosic biomass through HTL, in order to facilitate the pumpability of biomass aqueous slurries. Until now, HTL feedstock pumpability could only be achieved at solid mass content below 15%. In this work, two...... pretreatment methods to obtain wood-based slurries with more than 20% solid mass content, for continuous processing in HTL systems, are proposed. The effect of biomass particle size and pretreatment method on the feedstock pumpability is analyzed. The experimental results show that pumpable wood-based slurries...

U.S. DOE indirect coal liquefaction program: An overview

Energy Technology Data Exchange (ETDEWEB)

Shen, J.; Schmetz, E.; Winslow, J.; Tischer, R. [Dept. of Energy, Germantown, MD (United States); Srivastava, R.

1997-12-31

Coal is the most abundant domestic energy resource in the United States. The Fossil Energy Organization within the US Department of Energy (DOE) has been supporting a coal liquefaction program to develop improved technologies to convert coal to clean and cost-effective liquid fuels to complement the dwindling supply of domestic petroleum crude. The goal of this program is to produce coal liquids that are competitive with crude at $20 to $25 per barrel. Indirect and direct liquefaction routes are the two technologies being pursued under the DOE coal liquefaction program. This paper will give an overview of the DOE indirect liquefaction program. More detailed discussions will be given to the F-T diesel and DME fuels which have shown great promises as clean burning alternative diesel fuels. The authors also will briefly discuss the economics of indirect liquefaction and the hurdles and opportunities for the early commercial deployment of these technologies. Discussions will be preceded by two brief reviews on the liquid versus gas phase reactors and the natural gas versus coal based indirect liquefaction.

Coal liquefaction policy in China: Explaining the policy reversal since 2006

International Nuclear Information System (INIS)

Rong Fang; Victor, David G.

2011-01-01

China has emerged as a leader in coal liquefaction. While the country's abundant coal resources and acute concerns about oil security help explain China's interest in liquefaction, the driving forces for this industry are complicated and policy has been inconsistent. Since 2006 Beijing has tried to slow down the development of liquefaction; even as China has become more dependent on imported oil, the central government has been wary about the large impact of liquefaction technologies on scarce resources such as water. However, local government officials in coal rich areas have strong incentives to pour investment into the technology, which helps explain the uneven development and policy. The future of coal liquefaction will depend on how these forces unfold along with major Beijing-led reforms in the Chinese coal industry, which is closing smaller mines and favoring the emergence of larger coal producing firms. Those reforms will have mixed effects on liquefaction. They temporarily contribute to higher prices for coal while over the longer term creating coal companies that have much greater financial and technical skills needed to deploy technologies such as coal liquefaction at a scale needed if this energy pathway is to be competitive with conventional sources of liquid fuel. - Highlights: ► We explain swings in Chinese policy on coal liquefaction, a possible substitute for imported oil. ► Since 2006 Beijing's support has waned due to fears about environmental impacts and cost of liquefaction. ► Local governments in some coal rich regions remain strongly supportive. ► Volatile oil prices and rising coal prices make this industry more risky than previously thought. ► Consolidation of the coal industry will have mixed effects on viability of liquefaction projects.

Sinking during earthquakes: Critical acceleration criteria control drained soil liquefaction

Science.gov (United States)

Clément, C.; Toussaint, R.; Stojanova, M.; Aharonov, E.

2018-02-01

This article focuses on liquefaction of saturated granular soils, triggered by earthquakes. Liquefaction is defined here as the transition from a rigid state, in which the granular soil layer supports structures placed on its surface, to a fluidlike state, in which structures placed initially on the surface sink to their isostatic depth within the granular layer. We suggest a simple theoretical model for soil liquefaction and show that buoyancy caused by the presence of water inside a granular medium has a dramatic influence on the stability of an intruder resting at the surface of the medium. We confirm this hypothesis by comparison with laboratory experiments and discrete-element numerical simulations. The external excitation representing ground motion during earthquakes is simulated via horizontal sinusoidal oscillations of controlled frequency and amplitude. In the experiments, we use particles only slightly denser than water, which as predicted theoretically increases the effect of liquefaction and allows clear depth-of-sinking measurements. In the simulations, a micromechanical model simulates grains using molecular dynamics with friction between neighbors. The effect of the fluid is captured by taking into account buoyancy effects on the grains when they are immersed. We show that the motion of an intruder inside a granular medium is mainly dependent on the peak acceleration of the ground motion and establish a phase diagram for the conditions under which liquefaction happens, depending on the soil bulk density, friction properties, presence of water, and peak acceleration of the imposed large-scale soil vibrations. We establish that in liquefaction conditions, most cases relax toward an equilibrium position following an exponential in time. We also show that the equilibrium position itself, for most liquefaction regimes, corresponds to the isostatic equilibrium of the intruder inside a medium of effective density. The characteristic time to relaxation is

Earthquake-induced liquefaction in Ferland, Quebec

International Nuclear Information System (INIS)

Tuttle, M.; Seeber, L.

1991-02-01

Detailed geological investigations are under way at a number of liquefaction sites in the Ferland-Boilleau valley, Quebec, where sand boils, ground cracks and liquefaction-related damages to homes were documented immediately following the Ms=6.0, Mblg=6.5 Saguenay earthquake of November 25, 1988. To date, results obtained from these subsurface investigations of sand boils at two sites in Ferland, located about 26 km from the epicentre, indicate that: the Saguenay earthquake induced liquefaction in late-Pleistocene and Holocene sediments which was recorded as sand dikes, sills and vents in near-surface sediments and soils; earthquake-induced liquefaction and ground failure have occurred in this area at least three times in the past 10,000 years; and, the size and morphology of liquefaction features and the liquefaction susceptibility of source layers of the features may be indicative of the intensity of ground shaking. These preliminary results are very promising and suggest that with continued research liquefaction features will become a useful tool in glaciated terrains, such as northeastern North America, for determining not only the timing and location but also the size of past earthquakes

Potential of soil liquefaction at Perlis, northern region of Malalysia

Science.gov (United States)

Ghazaly, Zuhayr Md; Rahim, Mustaqqim Abdul; Nasir, Mohamad Amzar Bin Mhd; Isa, Nur Fitriah; Zaki, Mohd Faiz Mohammad; Hassan, Zulkarnain Bin; Ismail, Zul-Atfi Bin

2017-09-01

Soil liquefaction is earthquake's secondary effect which could cause fatal damages and structures instability. Despite Malaysia been located in stable zone of Pacific Ring of Fire, few significant surrounded quakes like Sumatra-Andaman earthquake had prompted Malaysian's public concern, especially in Perlis area, on local seismic resistant. Hence, this research presents the analysis result of liquefaction potential of the soils, as the secondary effect of earthquake, within Perlis, northern region of Malaysia; the next strong and sustainable metropolis by using semi-empirical procedures introduced by Seed and Idriss. The study consists of two stages which were determination of the local geological and geotechnical site conditions within Perlis and analysis of soil liquefaction susceptibility by using various methods and liquefaction potential by using Simplified Procedure developed by Seed and Idriss on stress approach. There were consist of four phases implemented in order to achieve the objectives targeted for the study after problem being identified. Firstly, a comprehensive review of literature on liquefaction at Perlis was carried out. Second phase was data collection process that includes collection of Site Investigation (SI) report. Thirdly, data analysis was carried out by utilizing suitable method. The final phase was to draw conclusion and recommendation for this study. It can be concluded that the overall Perlis due to earthquake moment magnitude below 7.5 has no potential to soil liquefaction. However, with the range of liquefaction potential of 1.60 to 5.64 in Kuala Perlis area, it is liquefiable. The development of liquefaction severity map of Perlis, Malaysia in this research, may be used by others as a reference for seismic design and standard safety measures as well as for further research work.

Experimental study on the liquefaction of cellulose in supercritical ethanol

Science.gov (United States)

Peng, Jinxing; Liu, Xinyuan; Bao, Zhenbo

2018-03-01

Cellulose is the major composition of solid waste for producing biofuel; cellulose liquefaction is helpful for realizing biomass supercritical liquefaction process. This paper is taking supercritical ethanol as the medium, liquefied cellulose with the intermittence installation of high press cauldron. Experiments have studied technical condition and the technology parameter of cellulose liquefaction in supercritical ethanol, and the pyrolysis mechanism was analysed based on the pyrolysis product. Results show that cellulose can be liquefied, can get good effect through appropriate technology condition. Under not catalyst, highest liquefaction rate of cellulose can reach 73.5%. The composition of the pyrolysis product was determined by GC-MS.

Liquefaction macrophenomena in the great Wenchuan earthquake

Science.gov (United States)

Chen, Longwei; Yuan, Xiaoming; Cao, Zhenzhong; Hou, Longqing; Sun, Rui; Dong, Lin; Wang, Weiming; Meng, Fanchao; Chen, Hongjuan

2009-06-01

On May 12, 2008 at 14:28, a catastrophic magnitude M s 8.0 earthquake struck the Sichuan Province of China. The epicenter was located at Wenchuan (31.00°N, 103.40°E). Liquefaction macrophenomena and corresponding destruction was observed throughout a vast area of 500 km long and 200 km wide following the earthquake. This paper illustrates the geographic distribution of the liquefaction and the relationship between liquefaction behavior and seismic intensity, and summarizes the liquefaction macrophenomena, including sandboils and waterspouts, ground subsidence, ground fissures etc., and relevant liquefaction features. A brief summary of the structural damage caused by liquefaction is presented and discussed. Based on comparisons with liquefaction phenomena observed in the 1976 Tangshan and 1975 Haicheng earthquakes, preliminary analyses were performed, which revealed some new features of liquefaction behavior and associated issues arising from this event. The site investigation indicated that the spatial non-uniformity of liquefaction distribution was obvious and most of the liquefied sites were located in regions of seismic intensity VIII. However, liquefaction phenomena at ten different sites in regions of seismic intensity VI were also observed for the first time in China mainland. Sandboils and waterspouts ranged from centimeters to tens of meters, with most between 1 m to 3 m. Dramatically high water/sand ejections, e.g., more than 10 m, were observed at four different sites. The sand ejections included silty sand, fine sand, medium sand, course sand and gravel, but the ejected sand amount was less than that in the 1976 Tangshan earthquake. Possible liquefaction of natural gravel soils was observed for the first time in China mainland.

Effect of process parameters on hydrothermal liquefaction of oil palm biomass for bio-oil production and its life cycle assessment

International Nuclear Information System (INIS)

Chan, Yi Herng; Yusup, Suzana; Quitain, Armando T.; Tan, Raymond R.; Sasaki, Mitsuru; Lam, Hon Loong; Uemura, Yoshimitsu

2015-01-01

Highlights: • Water is used as a clean solvent to liquefy palm biomass to bio-oil. • The optimum liquefaction condition of oil palm biomass is 390 °C and 25 MPa. • Optimum reaction time for liquefaction of empty fruit bunch and palm mesocarp fiber is 120 min. • Optimum reaction time for liquefaction of palm kernel shell is 240 min. • From the life cycle assessment, a net 2.29 kg CO 2 equivalent is generated per kg of bio-oil produced. - Abstract: This paper presents the studies on the effect of three process parameters; temperature, pressure and reaction time on the subcritical and supercritical hydrothermal liquefaction of oil palm empty fruit bunch, palm mesocarp fiber and palm kernel shell. The effect of temperature (330–390 °C), pressure (25–35 MPa) and reaction time (30–240 min) on bio-oil yields were investigated using a Inconel batch reactor. The optimum liquefaction condition for empty fruit bunch, palm mesocarp fiber and palm kernel shell was at supercritical condition of water; 390 °C and 25 MPa. For the effect of reaction time, bio-oil from empty fruit bunch and palm mesocarp fiber attained maximum yields at 120 min, whereas bio-oil yield from palm kernel shell continued to increase at reaction time of 240 min. Lastly, a life cycle assessment based on a conceptual biomass hydrothermal liquefaction process for bio-oil production was constructed and presented

Assessment of stone columns as a mitigation technique of liquefaction-induced effects during Italian earthquakes (May 2012).

Science.gov (United States)

Forcellini, Davide; Tarantino, Angelo Marcello

2014-01-01

Soil liquefaction has been observed worldwide during recent major earthquakes with induced effects responsible for much of the damage, disruption of function, and considerable replacement expenses for structures. The phenomenon has not been documented in recent time with such damage in Italian context before the recent Emilia-Romagna Earthquake (May 2012). The main lateral spreading and vertical deformations affected the stability of many buildings and impacted social life inducing valuable lessons on liquefaction risk assessment and remediation. This paper aims first of all to reproduce soil response to liquefaction-induced lateral effects and thus to evaluate stone column mitigation technique effectiveness by gradually increasing the extension of remediation, in order to achieve a satisfactory lower level of permanent deformations. The study is based on the use of a FE computational interface able to analyse the earthquake-induced three-dimensional pore pressure generation adopting one of the most credited nonlinear theories in order to assess realistically the displacements connected to lateral spreading.

Transport fuels from two-stage coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Benito, A.; Cebolla, V.; Fernandez, I.; Martinez, M.T.; Miranda, J.L.; Oelert, H.; Prado, J.G. (Instituto de Carboquimica CSIC, Zaragoza (Spain))

1994-03-01

Four Spanish lignites and their vitrinite concentrates were evaluated for coal liquefaction. Correlationships between the content of vitrinite and conversion in direct liquefaction were observed for the lignites but not for the vitrinite concentrates. The most reactive of the four coals was processed in two-stage liquefaction at a higher scale. First-stage coal liquefaction was carried out in a continuous unit at Clausthal University at a temperature of 400[degree]C at 20 MPa hydrogen pressure and with anthracene oil as a solvent. The coal conversion obtained was 75.41% being 3.79% gases, 2.58% primary condensate and 69.04% heavy liquids. A hydroprocessing unit was built at the Instituto de Carboquimica for the second-stage coal liquefaction. Whole and deasphalted liquids from the first-stage liquefaction were processed at 450[degree]C and 10 MPa hydrogen pressure, with two commercial catalysts: Harshaw HT-400E (Co-Mo/Al[sub 2]O[sub 3]) and HT-500E (Ni-Mo/Al[sub 2]O[sub 3]). The effects of liquid hourly space velocity (LHSV), temperature, gas/liquid ratio and catalyst on the heteroatom liquids, and levels of 5 ppm of nitrogen and 52 ppm of sulphur were reached at 450[degree]C, 10 MPa hydrogen pressure, 0.08 kg H[sub 2]/kg feedstock and with Harshaw HT-500E catalyst. The liquids obtained were hydroprocessed again at 420[degree]C, 10 MPa hydrogen pressure and 0.06 kg H[sub 2]/kg feedstock to hydrogenate the aromatic structures. In these conditions, the aromaticity was reduced considerably, and 39% of naphthas and 35% of kerosene fractions were obtained. 18 refs., 4 figs., 4 tabs.

A novel vortex tube-based N2-expander liquefaction process for enhancing the energy efficiency of natural gas liquefaction

Directory of Open Access Journals (Sweden)

Qyyum Muhammad Abdul

2017-01-01

Full Text Available This research work unfolds a simple, safe, and environment-friendly energy efficient novel vortex tube-based natural gas liquefaction process (LNG. A vortex tube was introduced to the popular N2-expander liquefaction process to enhance the liquefaction efficiency. The process structure and condition were modified and optimized to take a potential advantage of the vortex tube on the natural gas liquefaction cycle. Two commercial simulators ANSYS® and Aspen HYSYS® were used to investigate the application of vortex tube in the refrigeration cycle of LNG process. The Computational fluid dynamics (CFD model was used to simulate the vortex tube with nitrogen (N2 as a working fluid. Subsequently, the results of the CFD model were embedded in the Aspen HYSYS® to validate the proposed LNG liquefaction process. The proposed natural gas liquefaction process was optimized using the knowledge-based optimization (KBO approach. The overall energy consumption was chosen as an objective function for optimization. The performance of the proposed liquefaction process was compared with the conventional N2-expander liquefaction process. The vortex tube-based LNG process showed a significant improvement of energy efficiency by 20% in comparison with the conventional N2-expander liquefaction process. This high energy efficiency was mainly due to the isentropic expansion of the vortex tube. It turned out that the high energy efficiency of vortex tube-based process is totally dependent on the refrigerant cold fraction, operating conditions as well as refrigerant cycle configurations.

A novel vortex tube-based N2-expander liquefaction process for enhancing the energy efficiency of natural gas liquefaction

Science.gov (United States)

Qyyum, Muhammad Abdul; Wei, Feng; Hussain, Arif; Ali, Wahid; Sehee, Oh; Lee, Moonyong

2017-11-01

This research work unfolds a simple, safe, and environment-friendly energy efficient novel vortex tube-based natural gas liquefaction process (LNG). A vortex tube was introduced to the popular N2-expander liquefaction process to enhance the liquefaction efficiency. The process structure and condition were modified and optimized to take a potential advantage of the vortex tube on the natural gas liquefaction cycle. Two commercial simulators ANSYS® and Aspen HYSYS® were used to investigate the application of vortex tube in the refrigeration cycle of LNG process. The Computational fluid dynamics (CFD) model was used to simulate the vortex tube with nitrogen (N2) as a working fluid. Subsequently, the results of the CFD model were embedded in the Aspen HYSYS® to validate the proposed LNG liquefaction process. The proposed natural gas liquefaction process was optimized using the knowledge-based optimization (KBO) approach. The overall energy consumption was chosen as an objective function for optimization. The performance of the proposed liquefaction process was compared with the conventional N2-expander liquefaction process. The vortex tube-based LNG process showed a significant improvement of energy efficiency by 20% in comparison with the conventional N2-expander liquefaction process. This high energy efficiency was mainly due to the isentropic expansion of the vortex tube. It turned out that the high energy efficiency of vortex tube-based process is totally dependent on the refrigerant cold fraction, operating conditions as well as refrigerant cycle configurations.

Study on thermochemical liquefaction of biomass feedstocks; Biomass genryo no yuka hanno tokusei ni kansuru kisoteki kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-02-10

Liquefaction is applied to various biomass wastes and unused biomass to study characteristics of the liquefaction in each case. The paper described the system of the conversion and use of biomass into energy, conducted the positioning of the liquefaction, and outlined a history of the liquefaction chemistry and the study. To obtain basic data of characteristics of the liquefaction of various biomass raw materials, the liquefaction was conducted changing operational factors for the purpose of clarifying the product distribution of oil and by-products and oil properties. A comprehensive consideration was made of the liquefaction based on basic data and literature reports on the liquefaction of various biomass. From the above-mentioned studies, it was concluded that the energy can be recovered in a form of oil by applying the liquefaction to various biomass materials. A series of the study clarified effects of various operational factors on characteristics of the liquefaction as well as effects of classification of biomass materials and composition of the materials on characteristics of the liquefaction. 141 refs., 78 figs., 56 tabs.

Novel bimetallic dispersed catalysts for temperature-programmed coal liquefaction. Final report

Energy Technology Data Exchange (ETDEWEB)

Chunshan Song; Schobert, H.H.; Parfitt, D.P. [and others

1997-11-01

Development of new catalysts is a promising approach to more efficient coal liquefaction. It has been recognized that dispersed catalysts are superior to supported catalysts for primary liquefaction of coals, because the control of initial coal dissolution or depolymerization requires intimate contact between the catalyst and coal. This research is a fundamental and exploratory study on catalytic coal liquefaction, with the emphasis on exploring novel bimetallic dispersed catalysts for coal liquefaction and the effectiveness of temperature-programmed liquefaction using dispersed catalysts. The primary objective of this research was to explore novel bimetallic dispersed catalysts from organometallic molecular precursors, that could be used in low concentrations but exhibit relatively high activity for efficient hydroliquefaction of coals under temperature-programmed conditions. We have synthesized and tested various catalyst precursors in liquefaction of subbituminous and bituminous coals and in model compound studies to examine how do the composition and structure of the catalytic precursors affect their effectiveness for coal liquefaction under different reaction conditions, and how do these factors affect their catalytic functions for hydrogenation of polyaromatic hydrocarbons, for cleavage of C-C bonds in polycyclic systems such as 4-(1-naphthylmethyl)bibenzyl, for hydrogenolysis of C-O bond such as that in dinaphthylether, for hydrodeoxygenation of phenolic compounds and other oxygen-containing compounds such as xanthene, and for hydrodesulfurization of polycyclic sulfur compounds such as dibenzothiophene. The novel bimetallic and monometallic precursors synthesized and tested in this project include various Mo- and Fe-based compounds.

Report on 1979 result of Sunshine Project (detailed design). Part 1. Forty t/day solvolysis coal liquefaction pilot plant; 1979 nendo 40T/nichi solvolysis sekitan pilot plant shosai sekkei. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

The subject design documents are the compilation of the result of the design operation for the 'detailed design of 40 t/day class solvolysis coal liquefaction pilot plant'. The design of this pilot plant was conducted using, as the fundamental reference, the basic data provided by Kyushu National Industrial Research Institute and Kyushu University and the results of a contract research on '1 t/day class solvolysis coal liquefaction plant'. The subject detailed design was intended for Phase 1 centering on a single stage liquefaction - coal liquefaction (transformation into pitch) by solvolysis liquefaction reaction. The areas covered consists of the pre-treatment process, material mixing process, reaction process, reaction freezing process, coke separation process, SR recovery process, pitch refining process, utility facilities, and waste water treatment facilities. Incidentally, the processes for which the design operation has been completed this year, particularly the reaction process, coke separation process, SR recovery process, etc., are in the field untrodden technologically in the world; therefore, their design method is supposed to be established from the results of the R and D on coal liquefaction, '1 t/day class solvolysis coal liquefaction plant.' (NEDO)

Report on 1979 result of Sunshine Project (detailed design). Part 1. Forty t/day solvolysis coal liquefaction pilot plant; 1979 nendo 40T/nichi solvolysis sekitan pilot plant shosai sekkei. 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-03-01

The subject design documents are the compilation of the result of the design operation for the 'detailed design of 40 t/day class solvolysis coal liquefaction pilot plant'. The design of this pilot plant was conducted using, as the fundamental reference, the basic data provided by Kyushu National Industrial Research Institute and Kyushu University and the results of a contract research on '1 t/day class solvolysis coal liquefaction plant'. The subject detailed design was intended for Phase 1 centering on a single stage liquefaction - coal liquefaction (transformation into pitch) by solvolysis liquefaction reaction. The areas covered consists of the pre-treatment process, material mixing process, reaction process, reaction freezing process, coke separation process, SR recovery process, pitch refining process, utility facilities, and waste water treatment facilities. Incidentally, the processes for which the design operation has been completed this year, particularly the reaction process, coke separation process, SR recovery process, etc., are in the field untrodden technologically in the world; therefore, their design method is supposed to be established from the results of the R and D on coal liquefaction, '1 t/day class solvolysis coal liquefaction plant.' (NEDO)

Optimization for microwave-assisted direct liquefaction of bamboo residue in glycerol/methanol mixtures

Science.gov (United States)

Jiulong Xie; Jinqiu Qi; Chungyun Hse; Todd F. Shupe

2015-01-01

Bamboo residues were liquefied in a mixture of glycerol and methanol in the presence of sulfuric acid using microwave energy. We investigated the effects of liquefaction conditions, including glycerol/methanol ratio, liquefaction temperature, and reaction time on the conversion yield. The optimal liquefaction conditions were under the temperature of 120

Pretreatment techniques for biofuels and biorefineries

Energy Technology Data Exchange (ETDEWEB)

Fang, Zhen (ed.) [Chinese Academy of Sciences, Kunming, YN (China). Xishuangbanna Tropical Botonical Garden

2013-02-01

The first book focused on pretreatment techniques for biofuels contributed by the world's leading experts. Extensively covers the different types of biomass, various pretreatment approaches and methods that show the subsequent production of biofuels and chemicals. In addition to traditional pretreatment methods, novel techniques are also introduced and discussed. An accessible reference work for students, researchers, academicians and industrialists in biorefineries. This book includes 19 chapters contributed by the world's leading experts on pretreatment methods for biomass. It extensively covers the different types of biomass (e.g. molasses, sugar beet pulp, cheese whey, sugarcane residues, palm waste, vegetable oil, straws, stalks and wood), various pretreatment approaches (e.g. physical, thermal, chemical, physicochemical and biological) and methods that show the subsequent production of biofuels and chemicals such as sugars, ethanol, extracellular polysaccharides, biodiesel, gas and oil. In addition to traditional methods such as steam, hot-water, hydrothermal, diluted-acid, organosolv, ozonolysis, sulfite, milling, fungal and bacterial, microwave, ultrasonic, plasma, torrefaction, pelletization, gasification (including biogas) and liquefaction pretreatments, it also introduces and discusses novel techniques such as nano and solid catalysts, organic electrolyte solutions and ionic liquids. This book offers a review of state-of-the-art research and provides guidance for the future paths of developing pretreatment techniques of biomass for biofuels, especially in the fields of biotechnology, microbiology, chemistry, materials science and engineering. It intends to provide a systematic introduction of pretreatment techniques. It is an accessible reference work for students, researchers, academicians and industrialists in biorefineries.

Co-liquefaction of micro algae with coal. 2; Bisai sorui to sekitan no kyoekika hanno. 2

Energy Technology Data Exchange (ETDEWEB)

Ueda, C.; Matsui, T.; Otsuki, M.; Ikenaga, N.; Suzuki, T. [Kansai University, Osaka (Japan). Faculty of Engineering

1996-10-28

For the removal and recycle of CO2, a global warming gas, utilization of photosynthesis by micro algae is investigated. Formed micro algae are decomposed into CO2, H2O and CH4 again, which does not result in the permanent fixation. For the effective utilization of these micro algae, creation of petroleum alternate energy was tried through the co-liquefaction of micro algae with coal. Were investigated influences of the reaction temperature during the co-liquefaction and influences of catalysts, such as Fe(CO)5-S, Ru(CO)12, and Mo(CO)6-S, which are effective for the coal liquefaction. Micro algae, such as chlorella, spirulina, and littorale, and Yallourn brown coal were tested. It was found that co-liquefaction of micro algae with coal can be successfully proceeded under the same conditions as the liquefaction of coal. The oil yield obtained from the co-liquefaction in the presence of Fe(CO)5-S, an effective catalyst for coal liquefaction, agreed appropriately with the arithmetical mean value from separate liquefaction of coal and micro algae. It was suggested that pyrrhotite, an active species for coal liquefaction, was sufficiently formed by increasing the addition of sulfur. 2 refs., 7 figs., 1 tab.

Beneficial synergistic effect on bio-oil production from co-liquefaction of sewage sludge and lignocellulosic biomass.

Science.gov (United States)

Leng, Lijian; Li, Jun; Yuan, Xingzhong; Li, Jingjing; Han, Pei; Hong, Yuchun; Wei, Feng; Zhou, Wenguang

2018-03-01

Co-liquefaction of municipal sewage sludge (MSS) and lignocellulosic biomass such as rice straw or wood sawdust at different mixing ratios and the characterization of the obtained bio-oil and bio-char were investigated. Synergistic effects were found during co-processing of MSS with biomass for production of bio-oil with higher yield and better fuel properties than those from individual feedstock. The co-liquefaction of MSS/rice straw (4/4, wt) increased the bio-oil yield from 22.74% (bio-oil yield from liquefaction of MSS individually) or 23.67% (rice straw) to 32.45%. Comparable increase on bio-oil yield was also observed for MSS/wood sawdust mixtures (2/6, wt). The bio-oils produced from MSS/biomass mixtures were mainly composed of esters and phenols with lower boiling points (degradation temperatures) than those from individual feedstock (identified with higher heavy bio-oil fractions). These synergistic effects were probably resulted from the interactions between the intermittent products of MSS and those of biomass during processing. Copyright © 2017 Elsevier Ltd. All rights reserved.

Liquefaction chemistry and kinetics: Hydrogen utilization studies

Energy Technology Data Exchange (ETDEWEB)

Rothenberger, K.S.; Warzinski, R.P.; Cugini, A.V. [Pittsburgh Energy Technology Center, PA (United States)] [and others

1995-12-31

The objectives of this project are to investigate the chemistry and kinetics that occur in the initial stages of coal liquefaction and to determine the effects of hydrogen pressure, catalyst activity, and solvent type on the quantity and quality of the products produced. The project comprises three tasks: (1) preconversion chemistry and kinetics, (2) hydrogen utilization studies, and (3) assessment of kinetic models for liquefaction. The hydrogen utilization studies work will be the main topic of this report. However, the other tasks are briefly described.

Cooperative research in coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Huffman, G.P.; Sendlein, L.V.A. (eds.)

1991-05-28

Significant progress was made in the May 1990--May 1991 contract period in three primary coal liquefaction research areas: catalysis, structure-reactivity studies, and novel liquefaction processes. A brief summary of the accomplishments in the past year in each of these areas is given.

Advances in Seabed Liquefaction and its Implications for Marine Structures

DEFF Research Database (Denmark)

Sumer, B. Mutlu

2013-01-01

A review is presented of recent advances in seabed liquefaction and its implications for marine structures. The review is organized in seven sections: Residual liquefaction, including the sequence of liquefaction, mathematical modelling, centrifuge modelling and comparison with standard wave-flum......-flume results; Momentary liquefaction; Floatation of buried pipelines; Sinking of pipelines and marine objects; Liquefaction at gravity structures; Stability of rock berms in liquefied soils; and Impact of seismic-induced liquefaction....

Hydrothermal liquefaction of biomass

DEFF Research Database (Denmark)

Toor, Saqib; Rosendahl, Lasse; Hoffmann, Jessica

2014-01-01

Biomass is one of the most abundant sources of renewable energy, and will be an important part of a more sustainable future energy system. In addition to direct combustion, there is growing attention on conversion of biomass into liquid en-ergy carriers. These conversion methods are divided...... into biochemical/biotechnical methods and thermochemical methods; such as direct combustion, pyrolysis, gasification, liquefaction etc. This chapter will focus on hydrothermal liquefaction, where high pressures and intermediate temperatures together with the presence of water are used to convert biomass...... into liquid biofuels, with the aim of describing the current status and development challenges of the technology. During the hydrothermal liquefaction process, the biomass macromolecules are first hydrolyzed and/or degraded into smaller molecules. Many of the produced molecules are unstable and reactive...

Evaluation of soil liquefaction potential for level ground during earthquakes. A summary report

International Nuclear Information System (INIS)

Seed, H.B.; Arango, I.; Chan, C.K.

1975-10-01

The results of a three-year research program conducted to investigate the settlement and liquefaction of sands under multi-directional shaking are evaluated. The investigation indicated that the behavior of a saturated sand under cyclic loading conditions is a function of its geologic and seismic history and grain structure as well as its placement density. It is concluded that the resistance to liquefaction of a sand deposit can best be estimated by laboratory testing on undisturbed samples. It is shown that cyclic triaxial tests used in conjunction with appropriate correction factors to account for multi-directional shaking, simple shear loading conditions, and overconsolidation effects can provide valid data on cyclic loading characteristics. The concepts of ''limited strain potential'' and acceptable value of the factor of safety against initial liquefaction are introduced. Finally, the two basic methods for evaluating liquefaction potential and the effects of liquefaction are reviewed and updated with the information obtained through this research effort

Report on the bituminous coal liquefaction sub-committee in fiscal 1992; 1992 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the bituminous coal liquefaction sub-committee in the Sunshine Project in fiscal 1992. With an intention of developing a technology on the process (NEDOL) suitable for liquefaction of wide range of coal types placing sub-bituminous coal at the center, researches were carried out by using a pilot plant, and engineering data purposed for practical application of the technology were acquired. The construction of the pilot plant was launched in fiscal 1991. It is necessary to execute the pilot plant plan steadily in the future, and at the same time, reliably acquire different data by means of supportive researches. Economic performance of the process is also important. The first sub-committee meeting presented the following agenda: the status of constructing the 150-t/d pilot plant, tests and investigations thereon, research works by using a 1-t/d PSU, development of the most suitable coal refining technology, development of a coal pretreatment technology, improvement of the distilled oil distribution, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. The second sub-committee meeting presented the following agenda: the status of constructing the pilot plant, tests and investigations on improving the performance of natural pylite catalyst and circulating solvent, technological investigations on structuring a liquefying reaction data analyzing system, studies using a 1-t/d PSU, development of the most suitable coal refining technology, studies on coal liquefaction conditions, and studies on solvent hydrogenating catalysts. (NEDO)

Energy-based numerical models for assessment of soil liquefaction

Directory of Open Access Journals (Sweden)

Amir Hossein Alavi

2012-07-01

Full Text Available This study presents promising variants of genetic programming (GP, namely linear genetic programming (LGP and multi expression programming (MEP to evaluate the liquefaction resistance of sandy soils. Generalized LGP and MEP-based relationships were developed between the strain energy density required to trigger liquefaction (capacity energy and the factors affecting the liquefaction characteristics of sands. The correlations were established based on well established and widely dispersed experimental results obtained from the literature. To verify the applicability of the derived models, they were employed to estimate the capacity energy values of parts of the test results that were not included in the analysis. The external validation of the models was verified using statistical criteria recommended by researchers. Sensitivity and parametric analyses were performed for further verification of the correlations. The results indicate that the proposed correlations are effectively capable of capturing the liquefaction resistance of a number of sandy soils. The developed correlations provide a significantly better prediction performance than the models found in the literature. Furthermore, the best LGP and MEP models perform superior than the optimal traditional GP model. The verification phases confirm the efficiency of the derived correlations for their general application to the assessment of the strain energy at the onset of liquefaction.

Liquefaction under drained condition, from the lab to reality ?

Science.gov (United States)

Clément, Cécile; Aharonov, Einat; Stojanova, Menka; Toussaint, Renaud

2015-04-01

Liquefaction constitutes a significant natural hazard in relation to earthquakes and landslides. This effect can cause buildings to tilt or sink into the soil, mud-volcanoes, floatation of buried objects, long-runout landslides, etc. In this work we present a new understanding regarding the mechanism by which buildings sink and tilt during liquefaction caused by earthquakes. Conventional understanding of liquefaction explains most observed cases as occurring in an undrained, under-compacted, layer of sandy soil saturated with water [1]: According to that understanding, the under compacted sandy layer has the tendency to compact when a load is applied. In our case the load comes from ground shaking during an earthquake. When the soil compacts, the fluid pore pressure rises. Because in undrained conditions the fluid cannot flow out, the pore pressure builds up. The weight of buildings is in this case transferred from the grains of the soil to the pore water. The soil loses its rigidity and it flows like a liquid. From this model scientists made theoretical and empirical laws for geotechnical use and buildings construction. Despite the success of this conventional model in many cases, liquefied soils were also observed under drained conditions, and in previously compacted soils, which doesn't agree with the assumption of the model quoted above. One of the famous liquefaction events is the Kobe port destruction during the 1995 earthquake. A simple calculation of the Deborah number following Goren et al ([2][3]) shows that the undrained constraint was not met below the Kobe port during the 1995 earthquake. We propose another model, of liquefaction in drained granular media. According to our model the mere presence of water in granular media is enough to cause liquefaction during an earthquake, provided that the water reaches close to the surface. Our computations are based on the buoyancy force, and we take into account the static fluid pressure only. For small

Assessment of liquefaction-induced hazards using Bayesian networks based on standard penetration test data

Science.gov (United States)

Tang, Xiao-Wei; Bai, Xu; Hu, Ji-Lei; Qiu, Jiang-Nan

2018-05-01

Liquefaction-induced hazards such as sand boils, ground cracks, settlement, and lateral spreading are responsible for considerable damage to engineering structures during major earthquakes. Presently, there is no effective empirical approach that can assess different liquefaction-induced hazards in one model. This is because of the uncertainties and complexity of the factors related to seismic liquefaction and liquefaction-induced hazards. In this study, Bayesian networks (BNs) are used to integrate multiple factors related to seismic liquefaction, sand boils, ground cracks, settlement, and lateral spreading into a model based on standard penetration test data. The constructed BN model can assess four different liquefaction-induced hazards together. In a case study, the BN method outperforms an artificial neural network and Ishihara and Yoshimine's simplified method in terms of accuracy, Brier score, recall, precision, and area under the curve (AUC) of the receiver operating characteristic (ROC). This demonstrates that the BN method is a good alternative tool for the risk assessment of liquefaction-induced hazards. Furthermore, the performance of the BN model in estimating liquefaction-induced hazards in Japan's 2011 Tōhoku earthquake confirms its correctness and reliability compared with the liquefaction potential index approach. The proposed BN model can also predict whether the soil becomes liquefied after an earthquake and can deduce the chain reaction process of liquefaction-induced hazards and perform backward reasoning. The assessment results from the proposed model provide informative guidelines for decision-makers to detect the damage state of a field following liquefaction.

Hydrothermal liquefaction of agricultural and forestry wastes: state-of-the-art review and future prospects.

Science.gov (United States)

Cao, Leichang; Zhang, Cheng; Chen, Huihui; Tsang, Daniel C W; Luo, Gang; Zhang, Shicheng; Chen, Jianmin

2017-12-01

Hydrothermal liquefaction has been widely applied to obtain bioenergy and high-value chemicals from biomass in the presence of a solvent at moderate to high temperature (200-550°C) and pressure (5-25MPa). This article summarizes and discusses the conversion of agricultural and forestry wastes by hydrothermal liquefaction. The history and development of hydrothermal liquefaction technology for lignocellulosic biomass are briefly introduced. The research status in hydrothermal liquefaction of agricultural and forestry wastes is critically reviewed, particularly for the effects of liquefaction conditions on bio-oil yield and the decomposition mechanisms of main components in biomass. The limitations of hydrothermal liquefaction of agricultural and forestry wastes are discussed, and future research priorities are proposed. Copyright © 2017 Elsevier Ltd. All rights reserved.

Methods of natural gas liquefaction and natural gas liquefaction plants utilizing multiple and varying gas streams

Science.gov (United States)

Wilding, Bruce M; Turner, Terry D

2014-12-02

A method of natural gas liquefaction may include cooling a gaseous NG process stream to form a liquid NG process stream. The method may further include directing the first tail gas stream out of a plant at a first pressure and directing a second tail gas stream out of the plant at a second pressure. An additional method of natural gas liquefaction may include separating CO.sub.2 from a liquid NG process stream and processing the CO.sub.2 to provide a CO.sub.2 product stream. Another method of natural gas liquefaction may include combining a marginal gaseous NG process stream with a secondary substantially pure NG stream to provide an improved gaseous NG process stream. Additionally, a NG liquefaction plant may include a first tail gas outlet, and at least a second tail gas outlet, the at least a second tail gas outlet separate from the first tail gas outlet.

Fiscal 1989 report. Coal liquefaction committee; 1989 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

The committee in this fiscal year had its 1st meeting in June 1989 and 2nd meeting in March 1990, when fiscal 1989 research and development programs and fiscal 1989 research and development results, etc., were reported and discussed. The operating status of the 1 ton/day PSU (process supporting unit) for bituminous coal liquefaction was reported and discussed. The report included its 1st operation for the demonstration of a long-term stable run under standard conditions that continued for trouble-free 50 days, the 2nd operation for the investigation of the effect of liquefaction reaction temperature in which the liquefaction yield recorded the maximum at 450 degrees C with the collection of coal oils of 55 wt.% on the average, and the 3rd operation for the investigation of the effects of liquefaction reaction pressure and catalyst injection size whose details were being analyzed. Reported in relation with the brown coal liquefaction pilot plant was a comprehensive operation of a series of 1st hydrogenation, solvent deashing, and 2nd hydrogenation processes completed after a continuous operation of 460 hours establishing a total operating time of 1050 hours. (NEDO)

Numerical analysis of stone columns in mitigating liquefaction effects in embankment fills

Energy Technology Data Exchange (ETDEWEB)

Borghei, Z.; Soroush, A. [Amirkabir University of Technology, Tehran, (Iran, Islamic Republic of); Noorzad, A. [Power and Water University of Technology, Tehran, (Iran, Islamic Republic of)

2010-07-01

The traditional approach to liquefaction in embankment fills is to use in-situ densification. The use of stone columns offers the possibility of preventing liquefaction and associated settlements while reducing the cost and time required for treatment. This paper investigated the behaviour of stone columns using a numerical method. The study focused on a case study, a sand layer beneath two wall tanks, butane and propane NGL, located on Siri Island, Persian Gulf, Iran. Numerical analyses were carried out to evaluate the rate of excess pore pressure build-up in the improved ground. The numerical model results were compared to the simulation results from a centrifuge test for a uniform 19m-thick liquefiable sand layer. The numerical methodology was verified. The results showed that the stone columns can significantly increase the rate of pore pressure dissipation and reduce the settlement. It was found that the installation process densifies the surrounding soil, decreasing the liquefaction potential.

Liquefaction resistance of calcareous sands

International Nuclear Information System (INIS)

Sandoval Vallejo, Eimar

2012-01-01

Calcareous sands are unique in terms of their origin, mineralogy, shape, fragility and intra particle porosity. This article presents results from an experimental program carried out to study the liquefaction resistance of a calcareous sand retrieved from Cabo Rojo at Puerto Rico. The experimental program included mineralogical characterization, index properties, and undrained cyclic triaxial tests on isotropically consolidated reconstituted samples. Due to the large variation in the calcareous sand properties, results are compared with previous researches carried out on other calcareous sands around the world. Results showed a wide range in the liquefaction resistance of the studied calcareous sands. Cabo Rojo sand experienced greater liquefaction resistance than most of the calcareous sands used for comparison. Important differences in the excess pore pressure generation characteristics were also found.

Exergy analysis of helium liquefaction systems based on modified Claude cycle with two-expanders

Science.gov (United States)

Thomas, Rijo Jacob; Ghosh, Parthasarathi; Chowdhury, Kanchan

2011-06-01

Large-scale helium liquefaction systems, being energy-intensive, demand judicious selection of process parameters. An effective tool for design and analysis of thermodynamic cycles for these systems is exergy analysis, which is used to study the behavior of a helium liquefaction system based on modified Claude cycle. Parametric evaluation using process simulator Aspen HYSYS® helps to identify the effects of cycle pressure ratio and expander flow fraction on the exergetic efficiency of the liquefaction cycle. The study computes the distribution of losses at different refrigeration stages of the cycle and helps in selecting optimum cycle pressures, operating temperature levels of expanders and mass flow rates through them. Results from the analysis may help evolving guidelines for designing appropriate thermodynamic cycles for practical helium liquefaction systems.

Co-Liquefaction of Elbistan Lignite with Manure Biomass; Part 3 - Effect of Reaction Time and Temperature

Science.gov (United States)

Koyunoglu, Cemil; Karaca, Hüseyin

2017-12-01

Most of the liquefaction process were carried out in a batch reactor, in which the residence time of the liquefaction products is long enough to favour the retrogressive reactions. To minimize retrogressive reactions, the liquefaction of coal was carried out in a flowing solvent reactor in which a fixed bed of coal is continuously permeated by hot solvent. Solvent flowing through the coal bed carries the liquefaction products out of the reactor. Unlike experiments carried out under similar conditions in a batch reactor no increase in solid residue is observed during long time high temperature runs in the flowing solvent reactor. There is a greater appreciation of the importance of retrograde, or polymerization, reactions. If the free radicals formed when coal breaks down are not quickly capped with hydrogen, they react with each other to form large molecules that are much harder to break down than the original coal. Reaction time impacts both the co-liquefaction cost and the product yield. So as to study this idea, the experiments of Elbistan Lignite (EL) with manure co-liquefaction carried out by changing the reaction time from 30 to 120 minutes. As a result, the greatest oil products yields obtained at 60 minutes. Therefore, by thinking about the oil products yield values acquired, the optimal reaction time was obtained to be 60 minutes for Elbistan lignite (EL) with manure liquefied with the temperature of 350°C and 400°C. Above 425°C did not examine because solvent (tetraline) loses its function after 425 °C. The obtained optimum temperature found 400°C due to higher total conversion of liquefaction products and also oil+gas yields.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil

Energy Technology Data Exchange (ETDEWEB)

Zheng, Ji-Lu, E-mail: triace@163.com; Zhu, Ming-Qiang; Wu, Hai-tang

2015-09-15

Highlights: • Swine carcasses can be converted to bio-oil by alkaline hydrothermal liquefaction. • It seems that the use of the bio-oil for heat or CHP is technically suitable. • Some valuable chemicals were found in the bio-oils. • The bio-oil and the solid residue constituted an energy efficiency of 93.63% for the feedstock. • The solid residue can be used as a soil amendment, to sequester C and for preparing activated carbon. - Abstract: It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, the effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2 wt% bio-oil, having a high heating value of 32.35 MJ/kg and a viscosity of 305cp, and 22 wt% solid residue were realized at a liquefaction temperature of 250 °C, a reaction time of 60 min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels.

Alkaline hydrothermal liquefaction of swine carcasses to bio-oil

International Nuclear Information System (INIS)

Zheng, Ji-Lu; Zhu, Ming-Qiang; Wu, Hai-tang

2015-01-01

Highlights: • Swine carcasses can be converted to bio-oil by alkaline hydrothermal liquefaction. • It seems that the use of the bio-oil for heat or CHP is technically suitable. • Some valuable chemicals were found in the bio-oils. • The bio-oil and the solid residue constituted an energy efficiency of 93.63% for the feedstock. • The solid residue can be used as a soil amendment, to sequester C and for preparing activated carbon. - Abstract: It is imperative that swine carcasses are disposed of safely, practically and economically. Alkaline hydrothermal liquefaction of swine carcasses to bio-oil was performed. Firstly, the effects of temperature, reaction time and pH value on the yield of each liquefaction product were determined. Secondly, liquefaction products, including bio-oil and solid residue, were characterized. Finally, the energy recovery ratio (ERR), which was defined as the energy of the resultant products compared to the energy input of the material, was investigated. Our experiment shows that reaction time had certain influence on the yield of liquefaction products, but temperature and pH value had bigger influence on the yield of liquefaction products. Yields of 62.2 wt% bio-oil, having a high heating value of 32.35 MJ/kg and a viscosity of 305cp, and 22 wt% solid residue were realized at a liquefaction temperature of 250 °C, a reaction time of 60 min and a pH value of 9.0. The bio-oil contained up to hundreds of different chemical components that may be classified according to functional groups. Typical compound classes in the bio-oil were hydrocarbons, organic acids, esters, ketones and heterocyclics. The energy recovery ratio (ERR) reached 93.63%. The bio-oil is expected to contribute to fossil fuel replacement in stationary applications, including boilers and furnaces, and upgrading processes for the bio-oil may be used to obtain liquid transport fuels

Whole Algae Hydrothermal Liquefaction Technology Pathway

Energy Technology Data Exchange (ETDEWEB)

Biddy, M.; Davis, R.; Jones, S.

2013-03-01

This technology pathway case investigates the feasibility of using whole wet microalgae as a feedstock for conversion via hydrothermal liquefaction. Technical barriers and key research needs have been assessed in order for the hydrothermal liquefaction of microalgae to be competitive with petroleum-derived gasoline-, diesel-, and jet-range hydrocarbon blendstocks.

Secondary liquefaction in ethanol production

DEFF Research Database (Denmark)

2007-01-01

The invention relates to a method of producing ethanol by fermentation, said method comprising a secondary liquefaction step in the presence of a themostable acid alpha-amylase or, a themostable maltogenic acid alpha-amylase.......The invention relates to a method of producing ethanol by fermentation, said method comprising a secondary liquefaction step in the presence of a themostable acid alpha-amylase or, a themostable maltogenic acid alpha-amylase....

STUDIES ON SOIL LIQUEFACTION AND SETTLEMENT IN THE URAYASU DISTRICT USING EFFECTIVE STRESS ANALYSES FOR THE 2011 EAST JAPAN GREAT EARTHQUAKE

Science.gov (United States)

Fukutake, Kiyoshi; Jang, Jiho

The 2011 East Japan Great Earthquake caused soil liquefaction over a wide area. In particular, severe soil liquefaction was reported in the northern parts of the reclaimed lands around Tokyo Bay, even though the seismic intensity in this area was only about 5 on the Japan scale with low acceleration. The authors surveyed the residual settlement in the Urayasu district and then conducted effective stress analyses of areas affected and not affected by liquefaction. The analyses compared with the acceleration waves monitored with K-NET Urayasu or ground settlements surveyed. It is based on the acceleration observed on the seismic bedrocks in earthquake engineering in some other districts adjacent to Urayasu. Much of the settlement was due to the long duration of the earthquake, with further settlement resulting from the aftershock. The study shows that the affects of aftershocks need to be monitored, as well as needs for improvement of simplified liquefaction prediction methods using the factor of safety, FL.

Development of continuous bench scale unit for direct liquefaction

Energy Technology Data Exchange (ETDEWEB)

Yoon, Wang Lai [Korea Inst. of Energy and Resources, Daeduk (Korea, Republic of)

1996-12-31

Batch coal liquefaction experiments using tubing bombs and continuous experiments by cell liquefaction test facility were carried out. The main purpose was to maximize the coal liquefaction yields by improving the activity of coal dissolution catalysts which are oil soluble transition metal naphthenate and to supplement the incomplete research results. In the meantime, the study on the reaction characteristics of coal liquefaction and coal liquid upgrading catalyst upon sulfiding conditions and phosphorous addition have been conducted (author). 102 refs., 35 figs.

Development of continuous bench scale unit for direct liquefaction

Energy Technology Data Exchange (ETDEWEB)

Yoon, Wang Lai [Korea Inst. of Energy and Resources, Daeduk (Korea, Republic of)

1995-12-31

Batch coal liquefaction experiments using tubing bombs and continuous experiments by cell liquefaction test facility were carried out. The main purpose was to maximize the coal liquefaction yields by improving the activity of coal dissolution catalysts which are oil soluble transition metal naphthenate and to supplement the incomplete research results. In the meantime, the study on the reaction characteristics of coal liquefaction and coal liquid upgrading catalyst upon sulfiding conditions and phosphorous addition have been conducted (author). 102 refs., 35 figs.

Prospect of coal liquefaction in Indonesia

International Nuclear Information System (INIS)

Hartiniati; Dasuki, A.S.; Artanto, Yu.; Sulaksono, D.; Gunanjar

1997-01-01

With the current known oil reserves of about 11 billion barrel and annual production of approximately 500 million barrel, the country's oil reserves will be depleted by 2010, and Indonesia would have become net oil importer if no major oil fields be found somewhere in the archipelago. Under such circumstances the development of new sources of liquid fuel becomes a must, and coal liquefaction can be one possible solution for the future energy problem in Indonesia, particularly in the transportation sector due to the availability of coal in huge amount. This paper present the prospect of coal liquefaction in Indonesia and look at the possibility of integrating the process with HTR as a heat supplier. Evaluation of liquidability of several low grade Indonesian coals will also be presented. Coal from South Banko-Tanjung Enim is found to be one of the most suitable coal for liquefaction. Several studies show that an advanced coal liquefaction technology recently developed has the potential to reduce not only the environmental impact but also the production cost. The price of oil produced in the year 2000 is expected to reach US $ 17.5 ∼ 19.2/barrel and this will compete with the current oil price. Not much conclusion can be drawn from the idea of integrating HTR with coal liquefaction plant due to limited information available. (author). 7 figs, 3 tabs

Liquefaction induced by earthquakes in Japan. Jiban no ekijoka/ekijoka saigai chosa kenkyu no seika

Energy Technology Data Exchange (ETDEWEB)

Tono, I [Nation Inst. for Enviromental Studies, Tsukuba (Japan)

1992-09-01

Disaster caused by liquefaction is an important problem for the development of water-front because most of the places suffered from liquefaction disasters recently are located on sandy grounds. The damaged cases in the past due to liquefaction induced by earthquakes are grouped into: subsidence and inclination caused by the loss of supporting force of the ground, coming to the surface of buried structures due to excess pore hydrostatic pressure, destruction of lifeline accompanying the fluidization of ground, breakdown of bulkhead, retaining wall, etc. by increased earth pressure, sinking of soil structures, ground fissure, sliding, and immersion in floods and submergence of farms due to spouting of underground water. As regards prediction of liquefaction, description is made on the prediction of the occurrence of liquefaction and liquefaction prediction for which sedimentation environment is taken into consideration. Open-cut investigation can be said as the most effective means for accurate learning of the depth, thickness and sedimentation structure of liquefied layers. Liquefaction layers found in remains are also introduced. 16 refs., 6 figs.

A spotlight on liquefaction: evidence from clinical settings and experimental models in tuberculosis.

Science.gov (United States)

Cardona, Pere-Joan

2011-01-01

Liquefaction is one of the most intriguing aspects of human tuberculosis. It is a major cause of the transition from the infection to active disease (tuberculosis, TB) as well as the transmission of M. tuberculosis to other persons. This paper reviews the natural history of liquefaction in humans from a pathological and radiological point of view and discusses how the experimental models available can be used to address the topic of liquefaction and cavity formation. Different concepts that have been related to liquefaction, from the influence of immune response to mechanical factors, are reviewed. Synchronic necrosis or apoptosis of infected macrophages in a close area, together with an ineffective fibrosis, appears to be clue in this process, in which macrophages, the immune response, and bacillary load interact usually in a particular scenario: the upper lobes of the lung. The summary would be that even if being a stochastic effect, liquefaction would result if the organization of the intragranulomatous necrosis (by means of fibrosis) would be disturbed.

Evaluating liquefaction potential. A case history

International Nuclear Information System (INIS)

Blystra, A.R.

1991-01-01

Several earthen hydropower embankment dams in the midwestern United States were constructed using hydraulic fill methods and are liable to liquefaction during an earthquake due to the use of very loose, saturated sand in the embankment or foundations. A case history is presented describing the methodology used in evaluating the liquefaction potential of the largest earthfill dam in Michigan. The methodology includes the use of standard penetration and cone penetration test data in the formulation of a simplified procedure. Field investigations, laboratory testing, and analyses used are described. In addition to the drilling program, field work included an extensive ground penetrating radar survey, acoustic emission testing, and an electrical resistivity survey. It was found that the lowest calculated factor of safety against liquefaction is 0.63 for a loose zone ca 140 feet below the top of the embankment, and the factor of safety against slope failure, should the zone liquefy, is 1.49. It was concluded that while liquefaction is possible, post earthquake stability is adequate. 6 refs., 3 figs., 1 tab

Two-stage coal liquefaction without gas-phase hydrogen

Science.gov (United States)

Stephens, H.P.

1986-06-05

A process is provided for the production of a hydrogen-donor solvent useful in the liquefaction of coal, wherein the water-gas shift reaction is used to produce hydrogen while simultaneously hydrogenating a donor solvent. A process for the liquefaction of coal using said solvent is also provided. The process enables avoiding the use of a separate water-gas shift reactor as well as high pressure equipment for liquefaction. 3 tabs.

Liquefaction Potential for Soil Deposits in Muscat, Oman

Science.gov (United States)

El Hussain, I. W.; Deif, A.; Girgis, M.; Al-Rawas, G.; Mohamed, A.; Al-Jabri, K.; Al-Habsi, Z.

2015-12-01

Muscat is located in the northeastern part of Oman on a narrow strip between Oman coast and Oman Mountains, which is the place for at least four earthquakes of order of 5.2 magnitude in the last 1300 years. The near surface geology of Muscat varies from hard rocks in the eastern, southern and western parts to dense and lose sediments in the middle and northern parts. Liquefaction occurs in saturated cohesionless soils when its shear strength decreased to zero due to the increase of pore pressure. More than 500 boreholes in Muscat area were examined for their liquefaction susceptibility based on the soil characteristics data. Only soils susceptible to liquefaction are further considered for liquefaction hazard assessment. Liquefaction occurs if the cyclic stress ratio (CSR) caused by the earthquake is higher than the cyclic resistance ratio (CRR) of the soil. CSR values were evaluated using PGA values at the surface obtained from previously conducted seismic hazard and microzonation studies. CRR for Muscat region is conducted using N values of SPT tests from numerous borehole data and the shear wave velocity results from 99 MASW surveys over the entire region. All the required corrections are conducted to get standardized (N1) 60 values, to correct shear-wave velocity, and scale the results for Mw 6.0 instead of the proposed 7.5 (magnitude scaling factor). Liquefaction hazard maps are generated using the minimum factor of safety (FS) at each site as a representative of the FS against liquefaction at that location. Results indicate that under the current level of seismic hazard, liquefaction potential is possible at few sites along the northern coast where alluvial soils and shallow ground water table are present. The expected soft soil settlement is also evaluated at each liquefiable site.

Two-stage liquefaction of a Spanish subbituminous coal

Energy Technology Data Exchange (ETDEWEB)

Martinez, M.T.; Fernandez, I.; Benito, A.M.; Cebolla, V.; Miranda, J.L.; Oelert, H.H. (Instituto de Carboquimica, Zaragoza (Spain))

1993-05-01

A Spanish subbituminous coal has been processed in two-stage liquefaction in a non-integrated process. The first-stage coal liquefaction has been carried out in a continuous pilot plant in Germany at Clausthal Technical University at 400[degree]C, 20 MPa hydrogen pressure and anthracene oil as solvent. The second-stage coal liquefaction has been performed in continuous operation in a hydroprocessing unit at the Instituto de Carboquimica at 450[degree]C and 10 MPa hydrogen pressure, with two commercial catalysts: Harshaw HT-400E (Co-Mo/Al[sub 2]O[sub 3]) and HT-500E (Ni-Mo/Al[sub 2]O[sub 3]). The total conversion for the first-stage coal liquefaction was 75.41 wt% (coal d.a.f.), being 3.79 wt% gases, 2.58 wt% primary condensate and 69.04 wt% heavy liquids. The heteroatoms removal for the second-stage liquefaction was 97-99 wt% of S, 85-87 wt% of N and 93-100 wt% of O. The hydroprocessed liquids have about 70% of compounds with boiling point below 350[degree]C, and meet the sulphur and nitrogen specifications for refinery feedstocks. Liquids from two-stage coal liquefaction have been distilled, and the naphtha, kerosene and diesel fractions obtained have been characterized. 39 refs., 3 figs., 8 tabs.

Mongolian coal liquefaction test; Mongorutan no ekika tokusei

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, H.; Kubo, H. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Tsedevsuren, T. [National Research Center of Chemistry and Technology of Coal in Mongoria (Mongolia)

1996-10-28

This paper describes the results of liquefaction tests of Mongolian coals using an autoclave and a flow micro reactor. Uvdughudag coal, Hootiinhonhor coal, and Shivee-Ovoo coal were used for liquefaction tests with an autoclave. Oil yields of Uvdughudag and Hootiinhonhor coals were 55.56 wt% and 55.29 wt%, respectively, which were similar to that of Wyoming coal. Similar results were obtained, as to produced gas and water yields. These coals were found to be suitable for coal liquefaction. Lower oil yield, 42.55 wt% was obtained for Shivee-Ovoo coal, which was not suitable for liquefaction. Liquefaction tests were conducted for Uvdughudag coal with a flow micro reactor. The oil yield was 55.7 wt%, which was also similar to that of Wyoming coal, 56.1 wt%. Hydrogen consumption of Uvdughudag coal was also similar to that of Wyoming coal. From these, Uvdughudag coal can be a prospective coal for liquefaction. From the distillation distribution of oil, distillate fraction yield below 350{degree}C of Uvdughudag coal was 50.7 wt%, which was much higher than that of Wyoming coal, 35.6 wt%. Uvdughudag coal is a coal with high light oil fraction yield. 2 figs., 5 tabs.

Coal liquefaction becomes viable

Energy Technology Data Exchange (ETDEWEB)

NONE

2005-11-15

In 2003 the May/June issue of CoalTrans International speculated that coal liquefaction would become viable due to falling coal prices. This has not proved the case but the sustained high oil price is sparking new interest. A survey by Energy Intelligence and Marketing Research during November 2005 revealed a growth in the number of projects under development or at the feasibility stage. The article reports projects in China, the USA, Australia, New Zealand, the Philippines and India. China is commissioning the first wave of large liquefaction plants. The key question is whether other countries, particularly the USA, will follow.

Liquefaction Microzonation of Babol City Using Artificial Neural Network

DEFF Research Database (Denmark)

Farrokhzad, F.; Choobbasti, A.J.; Barari, Amin

2012-01-01

that will be less susceptible to damage during earthquakes. The scope of present study is to prepare the liquefaction microzonation map for the Babol city based on Seed and Idriss (1983) method using artificial neural network. Artificial neural network (ANN) is one of the artificial intelligence (AI) approaches...... microzonation map is produced for research area. Based on the obtained results, it can be stated that the trained neural network is capable in prediction of liquefaction potential with an acceptable level of confidence. At the end, zoning of the city is carried out based on the prediction of liquefaction...... that can be classified as machine learning. Simplified methods have been practiced by researchers to assess nonlinear liquefaction potential of soil. In order to address the collective knowledge built-up in conventional liquefaction engineering, an alternative general regression neural network model...

Semi-automated landform classification for hazard mapping of soil liquefaction by earthquake

Science.gov (United States)

Nakano, Takayuki

2018-05-01

Soil liquefaction damages were caused by huge earthquake in Japan, and the similar damages are concerned in near future huge earthquake. On the other hand, a preparation of soil liquefaction risk map (soil liquefaction hazard map) is impeded by the difficulty of evaluation of soil liquefaction risk. Generally, relative soil liquefaction risk should be able to be evaluated from landform classification data by using experimental rule based on the relationship between extent of soil liquefaction damage and landform classification items associated with past earthquake. Therefore, I rearranged the relationship between landform classification items and soil liquefaction risk intelligibly in order to enable the evaluation of soil liquefaction risk based on landform classification data appropriately and efficiently. And I developed a new method of generating landform classification data of 50-m grid size from existing landform classification data of 250-m grid size by using digital elevation model (DEM) data and multi-band satellite image data in order to evaluate soil liquefaction risk in detail spatially. It is expected that the products of this study contribute to efficient producing of soil liquefaction hazard map by local government.

Thermoeconomic optimization of a cryogenic refrigeration cycle for re-liquefaction of the LNG boil-off gas

Energy Technology Data Exchange (ETDEWEB)

Sayyaadi, Hoseyn; Babaelahi, M. [Faculty of Mechanical Engineering-Energy Division, K.N. Toosi University of Technology, P.O. Box: 19395-1999, No. 15-19, Pardis Str., Mollasadra Ave., Vanak Sq., Tehran 1999 143344 (Iran)

2010-09-15

The development of the liquefaction process for the Liquefied Natural Gas (LNG) boil-off re-liquefaction plants will be addressed to provide an environmentally friendly and cost effective solution for the gas transportation. In this manner, onboard boil-off gas (BOG) re-liquefaction system as a cryogenic refrigeration cycle is utilized in order to re-liquefy the BOG and returns it to the cargo tanks instead of burning it. In this paper, a thermoeconomic optimization of the LNG-BOG liquefaction system is performed. A thermoeconomic model based on energy and exergy analyses and an economic model according to the total revenue requirement (TRR) are developed. Minimizing of the unit cost of the refrigeration effect as a product of BOG re-liquefaction plant is performed using the genetic algorithm. Results of thermoeconomic optimization are compared with corresponding features of the base case system. Finally, sensitivity of the total cost of the system product with respect to the variation of some operating parameters is studied. (author)

Pyrolysis and liquefaction of acetone and mixed acetone/ tetralin swelled Mukah Balingian Malaysian sub-bituminous coal-The effect on coal conversion and oil yield

International Nuclear Information System (INIS)

Mohd Pauzi Abdullah; Mohd Azlan Mohd Ishak; Khudzir Ismail

2008-01-01

The effect of swelling on Mukah Balingian (MB) Malaysian sub-bituminous coal macrostructure was observed by pyrolysing the swelled coal via thermogravimetry under nitrogen at ambient pressure. The DTG curves of the pyrolyzed swelled coal samples show the presence of evolution peaks at temperature ranging from 235 - 295 degree Celsius that are due to releasing of light molecular weight hydrocarbons. These peaks, however, were not present in the untreated coal, indicating some changes in the coal macrostructure has occurred in the swelled coal samples. The global pyrolysis kinetics for coal that follows the first-order decomposition reaction was used to evaluate the activation energy of the pyrolyzed untreated and swelled coal samples. The results thus far have shown that the activation energy for the acetone and mixed acetone/ tetralin-swelled coal samples exhibit lower values than untreated coal, indicating less energy is required during the pyrolysis process due to the weakening of the coal-coal macromolecular interaction network. Moreover, liquefaction on the swelled coal samples that was carried out at temperatures ranging from 360 to 450 degree Celsius at 4 MPa of nitrogen pressure showed the enhancement of the coal conversion and oil yield at temperature of 420 degree Celsius, with retrogressive reaction started to dominate at higher temperature as indicated by decreased and increased in oil yield and high molecular weight pre-asphaltene, respectively. These observations suggest that the solvent swelling pre-treatment using acetone and mixed acetone/ tetralin can improve the coal conversion and oil yields at less severe liquefaction condition. (author)

Wave liquefaction in soils with clay content

DEFF Research Database (Denmark)

Kirca, Özgür; Sumer, B. Mutlu; Fredsøe, Jørgen

2012-01-01

The paper presents the results of an experimental study of the influence of clay content (in silt-clay and sand-clay mixtures) on liquefaction beneath progressive waves. The experiments showed that the influence of clay content is very significant. Susceptibility of silt to liquefaction is increa...

Effect of sulfur or hydrogen sulfide on initial stage of coal liquefaction in tetralin; Sekitan ekika shoki katei ni okeru io to ryuka suiso no hatasu yakuwari

Energy Technology Data Exchange (ETDEWEB)

Nakada, M. [Government Industrial Research Institute, Kyushu, Saga (Japan)

1996-10-28

It is well known that the solubilization of coal can be accelerated by adding sulfur or hydrogen sulfide during direct liquefaction of difficult coals. From the studies of authors on the coal liquefaction under the conditions at rather low temperatures between 300 and 400{degree}C, liquefaction products with high quality can be obtained by suppressing the aromatization of naphthene rings, but it was a problem that the reaction rate is slow. For improving this point, results obtained by changing solvents have been reported. In this study, to accelerate the liquefaction reaction, Illinois No.6 coal was liquefied in tetralin at temperature range from 300 to 400{degree}C by adding a given amount of sulfur or hydrogen sulfide at the initial stage of liquefaction. The addition of sulfur or hydrogen sulfide provided an acceleration effect of liquefaction reaction at temperature range between 300 and 400{degree}C. The addition of sulfur or hydrogen sulfide at 400{degree}C increased the oil products. At 370 and 400{degree}C, the liquid yield by adding sulfur was slightly higher than that by adding hydrogen sulfide, unexpectedly. The effects of sulfur and hydrogen sulfide were reversed when increasing the hydrogen pressure. 5 figs., 1 tab.

Coal liquefaction and gas conversion contractors review conference: Proceedings

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-11-01

This volume contains 55 papers presented at the conference. They are divided into the following topical sections: Direct liquefaction; Indirect liquefaction; Gas conversion (methane conversion); and Advanced research liquefaction. Papers in this last section deal mostly with coprocessing of coal with petroleum, plastics, and waste tires, and catalyst studies. Selected papers are indexed separately for inclusion in the Energy Science and Technology Database.

Coal liquefaction and gas conversion: Proceedings. Volume 1

Energy Technology Data Exchange (ETDEWEB)

1993-12-31

Volume I contains papers presented at the following sessions: AR-Coal Liquefaction; Gas to Liquids; and Direct Liquefaction. Selected papers have been processed separately for inclusion in the Energy Science and Technology Database.

A Spotlight on Liquefaction: Evidence from Clinical Settings and Experimental Models in Tuberculosis

Directory of Open Access Journals (Sweden)

Pere-Joan Cardona

2011-01-01

Full Text Available Liquefaction is one of the most intriguing aspects of human tuberculosis. It is a major cause of the transition from the infection to active disease (tuberculosis, TB as well as the transmission of M. tuberculosis to other persons. This paper reviews the natural history of liquefaction in humans from a pathological and radiological point of view and discusses how the experimental models available can be used to address the topic of liquefaction and cavity formation. Different concepts that have been related to liquefaction, from the influence of immune response to mechanical factors, are reviewed. Synchronic necrosis or apoptosis of infected macrophages in a close area, together with an ineffective fibrosis, appears to be clue in this process, in which macrophages, the immune response, and bacillary load interact usually in a particular scenario: the upper lobes of the lung. The summary would be that even if being a stochastic effect, liquefaction would result if the organization of the intragranulomatous necrosis (by means of fibrosis would be disturbed.

Japan`s New Sunshine Project. 20. 1995 annual summary of coal liquefaction and gasification

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-10-01

The paper described a summary of the 1995 study on coal liquefaction and gasification under the New Sunshine Project. As for coal liquefaction, a study was made of liquefaction characteristics and catalysts of various coals. Also studied were liquefaction conditions for quality improvement of liquefaction products, an evaluation method of quality of coal liquid, and a utilization method of coal liquid. In order to prevent carbonization and realize effective liquefaction, a study was conducted for elucidation of the reaction mechanism of high pressure hydrogenation. In a 150t/d pilot plant using hydrogen transfer hydrogenation solvents, the NEDOL method was studied using various catalysts and kinds of coals. This is a step prior to data acquisition for engineering, actual construction of equipment and operation. A 1t/d process supporting unit is a unit to support it. The unit conducts studies on slurry letdown valves and synthetic iron sulfide catalysts, screening of Chinese coals, etc. As to coal gasification, the paper added to the basic research the combined cycle power generation using entrained flow coal gasification for improvement of thermal efficiency and environmental acceptability and the HYCOL method for hydrogen production. 68 refs., 40 figs.

Prediction of strain energy-based liquefaction resistance of sand-silt mixtures: An evolutionary approach

Science.gov (United States)

Baziar, Mohammad H.; Jafarian, Yaser; Shahnazari, Habib; Movahed, Vahid; Amin Tutunchian, Mohammad

2011-11-01

Liquefaction is a catastrophic type of ground failure, which usually occurs in loose saturated soil deposits under earthquake excitations. A new predictive model is presented in this study to estimate the amount of strain energy density, which is required for the liquefaction triggering of sand-silt mixtures. A wide-ranging database containing the results of cyclic tests on sand-silt mixtures was first gathered from previously published studies. Input variables of the model were chosen from the available understandings evolved from the previous studies on the strain energy-based liquefaction potential assessment. In order to avoid overtraining, two sets of validation data were employed and a particular monitoring was made on the behavior of the evolved models. Results of a comprehensive parametric study on the proposed model are in accord with the previously published experimental observations. Accordingly, the amount of strain energy required for liquefaction onset increases with increase in initial effective overburden pressure, relative density, and mean grain size. The effect of nonplastic fines on strain energy-based liquefaction resistance shows a more complicated behavior. Accordingly, liquefaction resistance increases with increase in fines up to about 10-15% and then starts to decline for a higher increase in fines content. Further verifications of the model were carried out using the valuable results of some downhole array data as well as centrifuge model tests. These verifications confirm that the proposed model, which was derived from laboratory data, can be successfully utilized under field conditions.

Coal liquefaction technologies for producing ultra clean fuel

International Nuclear Information System (INIS)

Tahir, M.S.; Haq, N.U.; Nasir, H.; Islam, N.

2011-01-01

The expanding demand for petroleum, accompanied by the diminishing petroleum reserves and the energy security, has intensified the significance in coal liquefaction technologies (CTL) globally and specially in Pakistan. Pakistan is rich in coal resources, but short of petroleum. The Geological Survey of Pakistan based on wide spread drilling over an area of 9000 sq. km, a total of 175 billion tons of coal resource potential has been assessed. This paper overviews a general introduction on the mechanisms and processes of CLT such as direct coal liquefaction (DCL) and indirect coal liquefaction (ICL) technologies. (author)

FY 1981 Report on the results of Sunshine Project. Coal energy; 1981 nendo sunshine keikaku seika hokokusho. Sekitan energy

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-07-01

This report presents the results of (researches on solvolysis liquefaction mechanisms and reaction promotion with oil- and coal-based solvents), conducted as part of the research and development project for coal liquefaction techniques. The FY 1981 program includes researches on (1) the effects of liquefaction reaction conditions on liquefaction yield and production of light products for coal species of low degree of carbonization, including brown coal, (2) the effects of pretreatment of coal on its liquefaction reactivity, and (3) up-grading of the solvolysis coal liquid (SCL). For the item (1), HA240 (hydrogenated Ashland's A240) is used to investigate its liquefaction capacity for various coal species of low degree of carbonization, including brown coal. For the item (2), the effects of pretreatment in a hot water bath with reflux was investigated for sub-bituminous coal in the FY 1980. In the FY 1981, various pretreatment methods are attempted for enhancing liquefaction reactivity of brown coal. As a result, it is found that ash content of brown coal is decreased to one-third of the initial level, when it is treated in a diluted hydrochloric acid bath with reflux. For the item (3), SCL hydrogenated by Birch reduction (B-SCL, 1) is compared with H-SCL with respect to properties, structures and thermal crackability, to discuss the items required for the catalyst to be used in the second stage by clarifying effectiveness of the catalyst. (NEDO)

The Liquefaction of Hydrogen and Helium Using Small Coolers

International Nuclear Information System (INIS)

Green, Michael A.

2006-01-01

This report discusses the history of the liquefaction of hydrogen and helium using small coolers. This history dates form the 1960's when two stage GM coolers capable of reaching 7 K were used to liquefy helium and hydrogen by suing an added compressor and J-T circuit. Liquefaction using the added circuit failed to become mainstream because the J-T valve and heat exchanger clogged because of impurities in the gas being liquefied. Liquefaction using a GM cooler without an added J-T circuit proved to be difficult because the first stage was not used to pre-cool the gas coming to the second stage of the cooler. Once the gas being liquefied was pre-cooled using the cooler first stage, improvements in the liquefaction rates were noted. The advent of low temperature pulse tube cooler (down to 2.5 K) permitted one to achieve dramatic improvement is the liquefactions rates for helium. Similar but less dramatic improvements are expected for hydrogen as well. Using the PT-415 cooler, one can expect liquefaction rates of 15 to 20 liters per day for helium or hydrogen provided the heat leak into the cooler and the storage vessel is low. A hydrogen liquefier for MICE is presented at the end of this report

FY 1994 report on the Coal Liquefaction Committee; 1994 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

The paper reported the FY 1994 activities of the Coal Liquefaction Committee. The Coal Liquefaction Committee in this fiscal year was held on November 29, 1994 (1st) and March 22, 1995 (2nd), and report was made on the bituminous coal liquefaction study and state of the R and D of liquefaction base technology. Report was also made on the state of construction of bituminous coal liquefaction PP, outline of the results of the PSU operation, outline of the 11th Japan-U.S. JTM, etc. In the liquefaction base study, report/discussion were made about the improvement/rationalization of liquefaction process, study of innovative technology of coal liquefaction, study of coal liquefaction conditions, study for higher liquefaction element technology, project on the internationalization of coal liquefaction technology, etc. As to the relation of the entrained bed coal gasification power plant, report/discussion were made about survey/study on the processing of coal for coal gasification use (survey of coal kind selection, development of information processing system for coal conversion technology). Besides, as a topic, report was made on the economical evaluation/calculation of a commercial plant for brown coal liquefaction. (NEDO)

Status of health and environmental research relative to direct coal liquefaction: 1976 to the present

Energy Technology Data Exchange (ETDEWEB)

Gray, R.H.; Cowser, K.E. (eds.)

1982-06-01

This document describes the status of health and environmental research efforts, supported by the US Department of Energy (DOE), to assist in the development of environmentally acceptable coal liquefaction processes. Four major direct coal liquefaction processes are currently in (or have been investigated at) the pilot plant stage of development. Two solvent refined coal processes (SRC-I and -II), H-coal (a catalytic liquefaction process) and Exxon donor solvent (EDS). The Pacific Northwest Laboratory was assigned responsibility for evaluating SRC process materials and prepared comprehensive health and environmental effects research program plans for SRC-I and -II. A similar program plan was prepared for H-coal process materials by the Oak Ridge National Laboratory. A program has been developed for EDS process materials by Exxon Research and Engineering Co. The program includes short-term screening of coal-derived materials for potential health and ecological effects. Longer-term assays are used to evaluate materials considered most representative of potential commercial practice and with greatest potential for human exposure or release to the environment. Effects of process modification, control technologies and changing operational conditions on potential health and ecological effects are also being evaluated. These assessments are being conducted to assist in formulating cost-effective environmental research programs and to estimate health and environmental risks associated with a large-scale coal liquefaction industry. Significant results of DOE's health and environmental research efforts relative to coal liquefaction include the following: chemical characterization, health effects, ecological fate and effects, amelioration and risk assessment.

Japan's New Sunshine Project. 1994 annual summary of coal liquefaction and gasification

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

This paper summarizes the report for fiscal 1994 on research and development related to coal liquefaction and gasification. In the research and development of coal liquefaction technologies, reports were given on research of liquefaction characteristics of different coals and liquefaction process thereof, and on research of catalysts for the coal liquefaction. In the research and development of coal gasification technologies, reports were given on fundamental studies on gasification characteristics of different coals. In the research and development of liquefaction technologies for bituminous coal, reports were given on design, construction and operation of a bituminous coal liquefaction pilot plant with a capacity of 150 t/d, and the operation supporting studies on the pilot plant. In the fundamental research on the coal liquefaction process, reports were given on refining technologies and utilization of the refined materials, and studies on environment preservation in applying the coal liquefaction technologies. In the research on hydrogen manufacturing technologies by using the fundamental coal technology, reports were given on design, construction and operational studies of a pilot plant. In the research and development of the coal gasification technologies, reports were given on development of a jet-flow gasified coal electric power plant, selection of coals, and development of a data processing system. (NEDO)

Thermal properties of biopolyol from oil palm fruit fibre (OPFF) using solvolysis liquefaction technique

Science.gov (United States)

Kormin, Shaharuddin; Rus, Anika Zafiah M.; Azahari, M. Shafiq M.

2017-09-01

Liquefaction is known to be an effective method for converting biomass into a biopolyol. The biomass liquefaction of oil palm fruit waste (PFW) in the presence of liquefaction solvent/polyhydric alcohol (PA): polyethylene glycol 400 (PEG400) using sulfuric acid as catalyst was studied. For all experiments, the liquefaction was conducted at 150°C and atmospheric pressure. The mass ratio of OPFW to liquefaction solvents used in all the experiments was, 1/3. Thermogravimetric analyses (TGA) were used to analyze their biopolyol and residue behaviors. It was found that thermal stability of oil palm mesocarp fibre (PM), oil palm shell (PS) and oil palm kernel (PK) fibre exhibited the first degradation of hard segment at (232, 104, 230°C) and the second degradation of soft segment at (314, 226, 412°C) as compared to PM, PS and PK residue which (229, 102, 227°C) of hard segment and (310, 219, 299°C) of segment, respectively. This behavior of thermal degradation of the hard segment and soft segment of biopolyol was changes after undergo solvolysis liquefaction process. The result analysis showed that the resulting biopolyol and its residue was suitable monomer for polyurethane (PU) synthesis for the production of PU foams.

Numerical modeling of liquefaction-induced failure of geo-structures subjected to earthquakes

International Nuclear Information System (INIS)

Rapti, Ioanna

2016-01-01

The increasing importance of performance-based earthquake engineering analysis points out the necessity to assess quantitatively the risk of liquefaction. In this extreme scenario of soil liquefaction, devastating consequences are observed, e.g. excessive settlements, lateral spreading and slope instability. The present PhD thesis discusses the global dynamic response and interaction of an earth structure-foundation system, so as to determine quantitatively the collapse mechanism due to foundation's soil liquefaction. As shear band generation is a potential earthquake-induced failure mode in such structures, the FE mesh dependency of results of dynamic analyses is thoroughly investigated and an existing regularization method is evaluated. The open-source FE software developed by EDF R and D, called Code-Aster, is used for the numerical simulations, while soil behavior is represented by the ECP constitutive model, developed at Centrale-Supelec. Starting from a simplified model of 1D SH wave propagation in a soil column with coupled hydro-mechanical nonlinear behavior, the effect of seismic hazard and soil's permeability on liquefaction is assessed. Input ground motion is a key component for soil liquefaction apparition, as long duration of main shock can lead to important nonlinearity and extended soil liquefaction. Moreover, when a variation of permeability as function of liquefaction state is considered, changes in the dissipation phase of excess pore water pressure and material behavior are observed, which do not follow a single trend. The effect of a regularization method with enhanced kinematics approach, called first gradient of dilation model, on 1D SH wave propagation is studied through an analytical solution. Deficiencies of the use of this regularization method are observed and discussed, e.g. spurious waves apparition in the soil's seismic response. Next, a 2D embankment-type model is simulated and its dynamic response is evaluated in dry, fully drained

Hydrothermal Liquefaction of Biomass

Energy Technology Data Exchange (ETDEWEB)

Elliott, Douglas C.

2010-12-10

Hydrothermal liquefaction technology is describes in its relationship to fast pyrolysis of biomass. The scope of work at PNNL is discussed and some intial results are presented. HydroThermal Liquefaction (HTL), called high-pressure liquefaction in earlier years, is an alternative process for conversion of biomass into liquid products. Some experts consider it to be pyrolysis in solvent phase. It is typically performed at about 350 C and 200 atm pressure such that the water carrier for biomass slurry is maintained in a liquid phase, i.e. below super-critical conditions. In some applications catalysts and/or reducing gases have been added to the system with the expectation of producing higher yields of higher quality products. Slurry agents ('carriers') evaluated have included water, various hydrocarbon oils and recycled bio-oil. High-pressure pumping of biomass slurry has been a major limitation in the process development. Process research in this field faded away in the 1990s except for the HydroThermal Upgrading (HTU) effort in the Netherlands, but has new resurgence with other renewable fuels in light of the increased oil prices and climate change concerns. Research restarted at Pacific Northwest National Laboratory (PNNL) in 2007 with a project, 'HydroThermal Liquefaction of Agricultural and Biorefinery Residues' with partners Archer-Daniels-Midland Company and ConocoPhillips. Through bench-scale experimentation in a continuous-flow system this project investigated the bio-oil yield and quality that could be achieved from a range of biomass feedstocks and derivatives. The project was completed earlier this year with the issuance of the final report. HydroThermal Liquefaction research continues within the National Advanced Biofuels Consortium with the effort focused at PNNL. The bench-scale reactor is being used for conversion of lignocellulosic biomass including pine forest residue and corn stover. A complementary project is an international

Investigation of bio-composites using Novolac type liquefied wood resin: effects of liquefaction and fabrication conditions

Science.gov (United States)

Hui Pan; Chung-Yun Hse; Todd F. Shupe

2009-01-01

Wood liquefaction using an organic solvent and an acid catalyst has long been studied as a novel technique to utilize biomass as an alternative to petroleum-based products. Oxalic acid is a weaker organic acid than a mineral acid and wood liquefaction with oxalic acid as a catalyst will result in a higher amount of wood residue than that with a mineral acid....

Influence of clay content on wave-induced liquefaction

DEFF Research Database (Denmark)

Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

2014-01-01

of measurements were carried out: (1) pore-water pressure measurements across the soil depth and (2) water-surface elevation measurements. These measurements were synchronized with video recordings of the liquefaction process from the side. The ranges of the various quantities in the experiments were wave height...... of silt and clay was not liquefied. Sand may become prone to liquefaction with the introduction of clay, contrary to the general perception that this type of sediment is normally liquefaction-resistant under waves. For instance, sand with d50 50:4 mmwas liquefied with CC510:8%, whereas sand with d50 50...

Direct hydrothermal liquefaction of undried macroalgae Enteromorpha prolifera using acid catalysts

International Nuclear Information System (INIS)

Yang, Wenchao; Li, Xianguo; Liu, Shishi; Feng, Lijuan

2014-01-01

Highlights: • Bio-oil from liquefaction of wet E. prolifera was as feasible as dry powder. • Adding acid catalysts could improve the flow property of bio-oil. • Alkenes in the bio-oil converted to ketones in the presence of acid catalysts. • Content of 5-methyl furfural increased in the bio-oil obtained with acid catalysts. • Esters were formed in the bio-oil when adding sulfuric acid as a catalyst. - Abstract: Direct liquefaction of macroalgae Enteromorpha prolifera without predrying treatment was performed in a batch reactor. Effects of temperature, reaction time, biomass-to-water ratio and acid catalysts (sulfuric acid and acetic acid) on liquefaction products were investigated. Raw material and liquefaction products were analyzed by elemental analysis, Fourier transform infrared (FT-IR) and gas chromatography–mass spectrometry (GC–MS). Results showed that liquefaction at 290 °C for 20 min with 1:3 biomass-to-water ratio produced the highest bio-oil yield of 28.4 wt%, and high heating value (HHV) was 29.5 MJ/kg. Main components of bio-oil were fatty acids, ketones, alkenes and 5-methyl furfural, and main components of water soluble organics (WSOs) were pyridines, carboxylic acids and glycerol. In the bio-oil obtained with acid catalysts, content of ketones significantly increased while alkenes disappeared. Content of 5-methyl furfural also increased. Flow property of bio-oils was improved in the presence of acid catalysts. Moreover, esters were formed when adding sulfuric acid

Coal liquefaction committee report for fiscal 1981; 1981 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

For the assurance of smooth progress of coal technology development endeavors, the New Energy and Industrial Technology Development Organization (NEDO) has installed coal technology development committees (general committee on coal technologies, coal liquefaction committee, plant materials committee, coal type survey committee, total system committee, and coal gasification committee). The coal liquefaction committee deliberates and evaluates liquefaction technology and propels forward smoothly the efforts to develop the technology. Under the coal liquefaction committee, there are four subcommittees, which are the 1st subcommittee (primary liquefaction subcommittee), 2nd subcommittee (solid/liquid separation subcommittee), 3rd subcommittee (secondary hydrogenation subcommittee), and the 4th subcommittee (brown coal liquefaction subcommittee). The 2nd and 3rd subcommittees deal with common tasks as they were studied in fiscal 1980. The 1st subcommittee incorporates into itself the old subcommittees that respectively worked on the three liquefaction processes (the direct hydrogenation process, the solvent extraction process, and the Solvolysis process), and is designed to provide a site for information exchange. A brown coal liquefaction committee is incorporated into the coal liquefaction committee as the 4th subcommittee. This report is a compilation of the agendas of the respective subcommittees of the coal liquefaction committee. (NEDO)

Kinetics of coal liquefaction during heating-up and isothermal stages

Energy Technology Data Exchange (ETDEWEB)

Xian Li; Haoquan Hu; Shengwei Zhu; Shuxun Hu; Bo Wu; Meng Meng [Dalian University of Technology, Dalian (China). Institute of Coal Chemical Engineering

2008-04-15

Direct liquefaction of Shenhua bituminous coal was carried out in a 500 ml autoclave with iron catalyst and coal liquefaction cycle-oil as solvent at initial hydrogen of 8.0 MPa, residence time of 0-90 min. To investigate the liquefaction kinetics, a model for heating-up and isothermal stages was developed to estimate the rate constants of both stages. In the model, the coal was divided into three parts, easy reactive part, hard reactive part and unreactive part, and four kinetic constants were used to describe the reaction mechanism. The results showed that the model is valid for both heating-up and isothermal stages of liquefaction perfectly. The rate-controlled process for coal liquefaction is the reaction of preasphaltene plus asphaltene (PAA) to oil plus gas (O + G). The upper-limiting conversion of isothermal stage was estimated by the kinetic calculation. 21 refs., 4 figs., 4 tabs.

Effect of methanol on the liquefaction reaction of biomass in hot compressed water under microwave energy

Science.gov (United States)

Junming Xu; Jianchun Jiang; Chun-Yun Hse; Todd F. Shupe

2013-01-01

Liquefaction of sawdust was studied in methanol-water solutions using an acid catalyst under microwave energy. The effect of the methanol concentration on the changes of components in the liquefied products was analyzed by gas chromatography−mass spectrometry (GC−MS). It was found that 5-hydroxymethylfurfural (HMF) and levulinic acid are the...

[Longjintonglin Capsules for type IIIA prostatitis accompanied by abnormal semen liquefaction: A clinical observation].

Science.gov (United States)

Cai, Hong-cai; Wan, Chang-chun; Geng, Qiang; Liu, Wei; Zhang, Guo-wei; Shang, Xue-jun; Huang, Yu-feng

2016-01-01

To evaluate the therapeutic effect of Longjintonglin Capsules on type IIIA prostatitis accompanied by abnormal semen liquefaction. We selected 140 patients with type IIIA prostatitis accompanied by abnormal semen liquefaction according to the diagnostic standards of the American Institutes of Health (NIH) and treated them with Longjintonglin Capsules orally 3 capsules once tid for 12 weeks. We obtained the NIH Chronic Prostatitis Symptom Indexes (NIH-CPSI), traditional Chinese medicine (TCM) syndrome scores, leukocyte count in the expressed prostatic secretion (EPS), semen liquefaction time, and the results of semen analysis and compared these indicators before and after the treatment. Of the 140 cases, 132 were included in this study, excluding 8 due to their incomplete case histories. Before and after 4, 8 and 12 weeks of medication, the total NIH-CPSI scores were 24.52 ± 5.43, 21.28 ± 4.85, 18.01 ± 4.28, and 14.49 ± 3.65 (P prostatitis were cured and another 72 well responded, with an overall response rate of 78.0%. Of those with abnormal semen liquefaction, 61 were cured, 39 well responded, and 32 failed to respond, with an overall effectiveness rate of 75.8%. Semen analysis showed significantly increased percentage of progressively motile sperm after 4, 8 and 12 weeks of medication as compared with the baseline (P prostatitis accompanied by abnormal semen liquefaction.

Japan`s sunshine project. 17.. 1992 annual summary of coal liquefaction and gasification

Energy Technology Data Exchange (ETDEWEB)

1993-09-01

This report describes the achievement of coal liquefaction and gasification technology development in the Sunshine Project for FY 1992. It presents the research and development of coal liquefaction which includes studies on reaction mechanism of coal liquefaction and catalysts for coal liquefaction, the research and development of coal gasification technologies which includes studies on gasification characteristics of various coals and improvement of coal gasification efficiency, the development of bituminous coal liquefaction which includes engineering, construction and operation of a bituminous coal liquefaction pilot plant and research by a process supporting unit (PSU), the development of brown coal liquefaction which includes research on brown coal liquefaction with a pilot plant and development of techniques for upgrading coal oil from brown coal, the development of common base technologies which includes development of slurry letdown valves and study on upgrading technology of coal-derived distillates, the development of coal-based hydrogen production technology with a pilot plant, the development of technology for entrained flow coal gasification, the assessment of coal hydrogasification, and the international co-operation. 4 refs., 125 figs., 39 tabs.

Investigation of Bioethanol Productivity from Sargassum sp. (Brown Seaweed) by Pressure Cooker and Steam Cooker Pretreatments

International Nuclear Information System (INIS)

Yu Yu Wah; Kyaw Nyein Aye; Tint Tint Kyaw; Moe Moe Kyaw

2011-12-01

Production of biothanol from Sargassum sp. (Brown seaweed) is more suitable than using any other raw materials because it can easily collect on Chaung Tha Beach in Myanmar without any environmental damages. In this regard an attempt for bioethanol production from sargassum sp. by separation hydrolysis and fermentation (SHF) with saccharomyces cerevisiae was made. Sargassum sp. was pretreated with steam cooker at 120 C and 1 bar for 30 min and pressure cooker at 65 C for 2 hour. The pretreated sargassum sp. was liquefied with the crude enzyme from Trichoderma sp. at the temperature of 50 C and pH of 4 for the first liquefaction step and 95 C, pH of 5 and enzyme of SPEZYME FERD were employed for the second liquefaction step. OPTIDEX L-400 was used as saccharified enzyme with the temperature of 65 C and pH of 4.5 at saccharification step. The process of fermentation was followed by distillation at 78 C for alcohol extraction. Concentrations of crude ethanol were about 1.8% by using steam cooker and 2% for pressure cooker treatment with enzyme mediated saccharification followed by yeast fermentation. Yields of bioethanol were 23% for pressure cooker treatment and 21% for steam cooker treatment at SHF process.

On the risk of liquefaction of buffer and backfill

Energy Technology Data Exchange (ETDEWEB)

Pusch, R. [Geodevelopment AB, Lund (Sweden)

2000-10-01

The necessary prerequisites for liquefaction of buffers and backfills in a KBS-3 repository exist but the stress conditions and intended densities practically eliminate the risk of liquefaction for single earthquakes with magnitudes up to M=8 and normal duration. For buffers rich in expandable minerals it would be possible to reduce the density at water saturation to 1,700 - 1,800 kg/m{sup 3} or even less without any significant risk of liquefaction, while the density at saturation of backfills with 10 - 15% expandable clay should not be reduced to less than about 1,900 kg/m{sup 3}. Since the proposed densities of both buffers and backfills will significantly exceed these minimum values it is concluded that there is no risk of liquefaction of the engineered soil barriers in a KBS-3 repository even for very significant earthquakes.

On the risk of liquefaction of buffer and backfill

International Nuclear Information System (INIS)

Pusch, R.

2000-10-01

The necessary prerequisites for liquefaction of buffers and backfills in a KBS-3 repository exist but the stress conditions and intended densities practically eliminate the risk of liquefaction for single earthquakes with magnitudes up to M=8 and normal duration. For buffers rich in expandable minerals it would be possible to reduce the density at water saturation to 1,700 - 1,800 kg/m 3 or even less without any significant risk of liquefaction, while the density at saturation of backfills with 10 - 15% expandable clay should not be reduced to less than about 1,900 kg/m 3 . Since the proposed densities of both buffers and backfills will significantly exceed these minimum values it is concluded that there is no risk of liquefaction of the engineered soil barriers in a KBS-3 repository even for very significant earthquakes

Assessment of Soil Liquefaction Potential Based on Numerical Method

DEFF Research Database (Denmark)

Choobasti, A. Janalizadeh; Vahdatirad, Mohammad Javad; Torabi, M.

2012-01-01

Paying special attention to geotechnical hazards such as liquefaction in huge civil projects like urban railways especially in susceptible regions to liquefaction is of great importance. A number of approaches to evaluate the potential for initiation of liquefaction, such as Seed and Idriss...... simplified method have been developed over the years. Although simplified methods are available in calculating the liquefaction potential of a soil deposit and shear stresses induced at any point in the ground due to earthquake loading, these methods cannot be applied to all earthquakes with the same...... accuracy, also they lack the potential to predict the pore pressure developed in the soil. Therefore, it is necessary to carry out a ground response analysis to obtain pore pressures and shear stresses in the soil due to earthquake loading. Using soil historical, geological and compositional criteria...

Cooperative research in coal liquefaction. Final report, May 1, 1990-- April 30, 1991

Energy Technology Data Exchange (ETDEWEB)

Huffman, G.P. [ed.

1992-02-15

The Consortium for Fossil Fuel Liquefaction Science (CFFLS) is currently engaged in a three year contract with the US Department of Energy investigating a range of research topics dealing with direct coal liquefaction. This report summarizes the results of this program in its second year, from May 1, 1990 to April 30, 1991. Accomplishments for this period are presented for the following tasks: Iron-based catalysts for coal liquefaction, exploratory research on coal conversion, novel coal liquefaction concepts, and novel catalysts for coal liquefaction.

A novel process for small-scale pipeline natural gas liquefaction

International Nuclear Information System (INIS)

He, T.B.; Ju, Y.L.

2014-01-01

Highlights: • A novel process was proposed to liquefy natural gas by utilizing the pressure exergy. • The process is zero energy consumption. • The maximum liquefaction rate of the process is 12.61%. • The maximum exergy utilization rate is 0.1961. • The economic analysis showed that the payback period of the process is quit short. - Abstract: A novel process for small-scale pipeline natural gas liquefaction is designed and presented. The novel process can utilize the pressure exergy of the pipeline to liquefy a part of natural gas without any energy consumption. The thermodynamic analysis including mass, energy balance and exergy analysis are adopted in this paper. The liquefaction rate and exergy utilization rate are chosen as the objective functions. Several key parameters are optimized to approach the maximum liquefaction rate and exergy utilization rate. The optimization results showed that the maximum liquefaction rate is 12.61% and the maximum exergy utilization rate is 0.1961. What is more, the economic performances of the process are also discussed and compared by using the maximum liquefaction rate and exergy utilization rate as indexes. In conclusion, the novel process is suitable for pressure exergy utilization due to its simplicity, zero energy consumption and short payback period

Outline of research achievement of fiscal 1983. Development of coal liquefaction technologies; Sekitan ekika gijutsu kaihatsu. 1983 nendo kenkyu seika no gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-07-01

Reported are the results of (1) the development of bituminous coal liquefaction technology, (2) development of brown coal liquefaction technology, (3) experimental fabrication and development of plant equipment and materials therefor, and (4) a survey on coal type selection. The goals of the development are mentioned below. Under Item (1), an optimum liquefaction process and a solid/liquid separation process are to be defined, the effect of iron-based catalysts upon liquefaction reaction is to be elucidated, a technology for constructing a direct hydroliquefaction unit is to be established, and a plant using such a unit is to be developed. Under Item (2), an optimum liquefaction technology is to be established, high in economic efficiency and reliability, by subjecting Australia's Victoria brown coal to the direct liquefaction process. In particular, a new brown coal liquefaction technology is to be established, which will be an organic combination of a novel, raw brown coal slurry dehydration technology, a solvent deashing technology, and the secondary hydrogenation technology, all centering on the basic technology of primary hydrogenation. Under Item (3), reactor materials, accessory materials, slurry pumps, etc., are to be experimentally manufactured and developed further. Under Item (4), data are to be collected on coal resources, coal quality, liquefaction characteristics, etc., during the process of technology development for liquefaction, etc. Furthermore, methods are to be established for the effective utilization of liquefaction products and for their optimum refining. (NEDO)

Liquefaction assessment based on combined use of CPT and shear wave velocity measurements

Science.gov (United States)

Bán, Zoltán; Mahler, András; Győri, Erzsébet

2017-04-01

Soil liquefaction is one of the most devastating secondary effects of earthquakes and can cause significant damage in built infrastructure. For this reason liquefaction hazard shall be considered in all regions where moderate-to-high seismic activity encounters with saturated, loose, granular soil deposits. Several approaches exist to take into account this hazard, from which the in-situ test based empirical methods are the most commonly used in practice. These methods are generally based on the results of CPT, SPT or shear wave velocity measurements. In more complex or high risk projects CPT and VS measurement are often performed at the same location commonly in the form of seismic CPT. Furthermore, VS profile determined by surface wave methods can also supplement the standard CPT measurement. However, combined use of both in-situ indices in one single empirical method is limited. For this reason, the goal of this research was to develop such an empirical method within the framework of simplified empirical procedures where the results of CPT and VS measurements are used in parallel and can supplement each other. The combination of two in-situ indices, a small strain property measurement with a large strain measurement, can reduce uncertainty of empirical methods. In the first step by careful reviewing of the already existing liquefaction case history databases, sites were selected where the records of both CPT and VS measurement are available. After implementing the necessary corrections on the gathered 98 case histories with respect to fines content, overburden pressure and magnitude, a logistic regression was performed to obtain the probability contours of liquefaction occurrence. Logistic regression is often used to explore the relationship between a binary response and a set of explanatory variables. The occurrence or absence of liquefaction can be considered as binary outcome and the equivalent clean sand value of normalized overburden corrected cone tip

Report on results for fiscal 1997 on development of coal liquefaction technology . Development of liquefaction base technology (studies on development and internationalization of environmentally benign coal liquefaction technology); 1997 nendo sekitan ekika gijutsu seika hokokusho. Ekika kiban gijutsu no kaihatsu (kankyo chowagata sekitan ekika gijutsu no kaihatsu oyobi kokusaika kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

The research objective is the development of environmentally benign coal liquefaction technology and the studies on internationalization of coal liquefaction technology. Implemented for the former are (1) research on improvement and rationalization of liquefaction process and (2) research on advancement of liquefaction base technology. In (1), studies were made on in-oil preprocessing technology and scale suppressing measures for the purpose of obtaining reform/high grade of coal, and on improvement of liquefied oil collecting ratio, sophistication of coal slurry and attainment of light oil/high grade from liquefied crude oil for the purpose of optimizing liquefaction reactive conditions and improving a solvent. In (2), in developing high activity/high dispersion type new catalysts, catalytic sufurization behavior and activity manifestation mechanism were explored, as were iron hydroxide based iron ore properties and liquefaction reactive characteristics. The initial reactive characteristics of liquefaction for example were investigated for the purpose of collecting basic data for expanding kinds of coal. In order to attain the latter objective of the research, a feasibility study of liquefaction location was conducted, as were the investigation including sampling of iron ore for catalytic material and the investigation of coal gasification technology. After the completion of the Australian brown coal liquefaction project, the development of the coal liquefaction technology commenced in fiscal 1994 produced a number of useful records and ended in 1997. (NEDO)

Influence of saturation degree and role of suction in unsaturated soils behaviour: application to liquefaction

Directory of Open Access Journals (Sweden)

Vernay Mathilde

2016-01-01

Full Text Available The effect of the pore fluid compressibility on liquefaction has been studied by various authors. But few papers have been published about the role of suction in cyclic behavior of unsaturated soils. Most of these works use Skempton coefficient B as a reference in terms of saturation degree to analyze their results. The use of B in experimental conditions is convenient, but is not accurate when studying liquefaction behavior, since effects of suction are neglected. In this paper, the influence of saturation degree on mechanical behavior of a soil under dynamic loads is studied. Cyclic undrained triaxial tests were performed on sand samples, under various levels of saturation. Soil-water characteristic curve was used, in order to study influence of suction. The first results confirm that when the degree of saturation decreases, the resistance increases. Initial positive suction tends to stiffen the soil. It also appears that the presence of air delays the occurrence of liquefaction, but doesn’t prevent it. Indeed, liquefaction is observed, whether the soil is saturated or not.

Fiscal 1991 report. Coal liquefaction committee; 1991 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

The committee in this fiscal year had the 1st meeting in July 1991, the 2nd in August 1991, and the 3rd in March 1992, when fiscal 1990 research and development results, fiscal 1991 research and development programs, fiscal 1991 research and development results, etc., were reported and deliberated. At the 2nd meeting, the meaning of coal liquefaction technology development and how to go ahead with the task were described, which topic for discussion was entitled 'How coal liquefaction technology should be for the 21st century.' After discussion, it was agreed upon that a coal liquefaction technology package be completed in fiscal 2000 based on the absorption of each other's findings and on the utilization of basic studies common to both to be realized through the exchange of technologies between the brown coal liquefaction project and the bituminous coal liquefaction project. Under the brown coal liquefaction project, a 50 ton/day pilot plant was built and operated in Victoria, Australia, and the operation was completed in October 1990. The results of research and development under the coal brown liquefaction project will be compiled by fiscal 1993. (NEDO)

Direct catalytic hydrothermal liquefaction of spirulina to biofuels with hydrogen

Science.gov (United States)

Zeng, Qin; Liao, Hansheng; Zhou, Shiqin; Li, Qiuping; Wang, Lu; Yu, Zhihao; Jing, Li

2018-01-01

We report herein on acquiring biofuels from direct catalytic hydrothermal liquefaction of spirulina. The component of bio-oil from direct catalytic hydrothermal liquefaction was similar to that from two independent processes (including liquefaction and upgrading of biocrude). However, one step process has higher carbon recovery, due to the less loss of carbons. It was demonstrated that the yield and HHV of bio-oil from direct catalytic algae with hydrothermal condition is higher than that from two independent processes.

Development of liquefaction process of coal and biomass in supercritical water; Chorinkaisui wo mochiita sekitan biomass doji ekika process no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Nonaka, H.; Matsumura, Y.; Tsutsumi, A.; Yoshida, K. [The University of Tokyo, Tokyo (Japan). Faculty of Engineering; Masuno, Y.; Inaba, A. [National Institute for Resources and Environment, Tsukuba (Japan)

1996-10-28

Liquefaction of coal and biomass in supercritical water has been investigated, in which strong solubilization force of supercritical water against hydrocarbons is utilized. Free radicals are formed through the cleavage of covalent bonds in coal under the heating condition at around 400{degree}C during coal liquefaction. It is important to stabilize these unstable intermediate products by hydrogen transfer. On the other hand, hydrogen is not required for the liquefaction of biomass having higher H/C atomic ratio and oxygen content than those of coal. Co-liquefaction of coal and biomass was conducted using supercritical water, in which excess hydrogen from the liquefaction of biomass would be transferred to coal, resulting in the effective liquefaction of coal. Mixture of coal and cellulose was liquefied in supercritical water at 390{degree}C under the pressure of 25 MPa using a semi-continuous reactor, and the results were compared with those from the separate liquefaction of them. The co-liquefaction of coal and cellulose did not show any difference in the residue yield from the separate liquefaction of these, but led to the increased production of compounds with lower molecular weight. The liquefaction was completed in 15 minutes. 5 refs., 3 figs., 3 tabs.

FY 1992 report on the Coal Liquefaction Committee; 1992 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

The paper reported activities of the Coal Liquefaction Committee in FY 1992. In the 1st committee meeting, report/discussion were made of the summary of the FY 1992 R and D plan on the bituminous coal liquefaction, brown coal liquefaction and the common/basic technology. Further, the following were reported as topics: results of the operation by bituminous coal liquefaction PSU and small equipment, state of arrangement of the results of the brown coal liquefaction project, making of the basic policy for development of the common/basic technology, construction of package of coal liquefaction technology. In the 2nd committee meeting, the summary of the results of the FY 1992 R and D was reported/discussed. As to the development of bituminous coal liquefaction technology, study using pilot plant and support study were reported. Concerning the development of brown coal liquefaction technology, study using a 50t/d pilot plant and complementary study of operation. Relating to the development of the common/basic technology, trial manufacture/development of plant equipment/materials, survey of selection of coal kind, etc. The paper also reported a scheme on the evaluation of efficiency of the brown coal liquefaction process. (NEDO)

Assessment of liquefaction potential during earthquakes by arias intensity

Science.gov (United States)

Kayen, R.E.; Mitchell, J.K.

1997-01-01

An Arias intensity approach to assess the liquefaction potential of soil deposits during earthquakes is proposed, using an energy-based measure of the severity of earthquake-shaking recorded on seismograms of the two horizontal components of ground motion. Values representing the severity of strong motion at depth in the soil column are associated with the liquefaction resistance of that layer, as measured by in situ penetration testing (SPT, CPT). This association results in a magnitude-independent boundary that envelopes initial liquefaction of soil in Arias intensity-normalized penetration resistance space. The Arias intensity approach is simple to apply and has proven to be highly reliable in assessing liquefaction potential. The advantages of using Arias intensity as a measure of earthquake-shaking severity in liquefaction assessment are: Arias intensity is derived from integration of the entire seismogram wave form, incorporating both the amplitude and duration elements of ground motion; all frequencies of recorded motion are considered; and Arias intensity is an appropriate measure to use when evaluating field penetration test methodologies that are inherently energy-based. Predictor equations describing the attenuation of Arias intensity as a function of earthquake magnitude and source distance are presented for rock, deep-stiff alluvium, and soft soil sites.

Design of generic coal conversion facilities: Process release---Direct coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

1991-09-01

The direct liquefaction portion of the PETC generic direct coal liquefaction process development unit (PDU) is being designed to provide maximum operating flexibility. The PDU design will permit catalytic and non-catalytic liquefaction concepts to be investigated at their proof-of-the-concept stages before any larger scale operations are attempted. The principal variations from concept to concept are reactor configurations and types. These include thermal reactor, ebullating bed reactor, slurry phase reactor and fixed bed reactor, as well as different types of catalyst. All of these operating modes are necessary to define and identify the optimum process conditions and configurations for determining improved economical liquefaction technology.

Combined (alkaline+ultrasonic) pretreatment effect on sewage sludge disintegration.

Science.gov (United States)

Kim, Dong-Hoon; Jeong, Emma; Oh, Sae-Eun; Shin, Hang-Sik

2010-05-01

The individual effects of alkaline (pH 8-13) and ultrasonic (3750-45,000kJ/kg TS) pretreatments on the disintegration of sewage sludge were separately tested, and then the effect of combining these two methods at different intensity levels was investigated using response surface methodology (RSM). In the combined pretreatment, ultrasonic treatment was applied to the alkali-pretreated sludge. While the solubilization (SCOD/TCOD) increase was limited to 50% in individual pretreatments, it reached 70% in combined pretreatment, and the results clearly showed that preconditioning of sludge at high pH levels played a crucial role in enhancing the disintegration efficiency of the subsequent ultrasonic pretreatment. By applying regression analysis, the disintegration degree (DD) was fitted based on the actual value to a second order polynomial equation: Y=-172.44+29.82X(1)+5.30x10(-3)X(2)-7.53x10(-5)X(1)X(2)-1.10X(1)(2)-1.043x10(-7)X(2)(2), where X(1), X(2), and Y are pH, specific energy input (kJ/kg TS), and DD, respectively. In a 2D contour plot describing the tendency of DD with respect to pH and specific energy input, it was clear that DD increased as pH increased, but it seemed that DD decreased when the specific energy input exceeded about 20,000kJ/kg TS. This phenomenon tells us that there exists a certain point where additional energy input is ineffective in achieving further disintegration. A synergetic disintegration effect was also found in the combined pretreatment, with lower specific energy input in ultrasonic pretreatment yielding higher synergetic effect. Finally, in order to see the combined pretreatment effect in continuous operation, the sludge pretreated with low intensity alkaline (pH 9)/ultrasonic (7500kJ/kg TS) treatment was fed to a 3 L of anaerobic sequencing batch reactor after 70 days of control operation. CH(4) production yield significantly increased from 81.9+/-4.5mL CH(4)/g COD(added) to 127.3+/-5.0mL CH(4)/g COD(added) by pretreatment, and

Coal liquefaction process streams characterization and evaluation

Energy Technology Data Exchange (ETDEWEB)

Robbins, G.A.; Brandes, S.D.; Winschel, R.A.; Burke, F.P.

1992-03-01

CONSOL R D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-fold: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.

Residual liquefaction of seabed under standing waves

DEFF Research Database (Denmark)

Kirca, V.S. Ozgur; Sumer, B. Mutlu; Fredsøe, Jørgen

2013-01-01

This paper presents the results of an experimental study of the seabed liquefaction beneath standing waves. Silt (with d50 =0.070mm) was used in the experiments. Two kinds of measurements were carried out: pore water pressure measurements and water surface elevation measurements. These measurements...... were synchronized with video recording of the liquefaction process from the side. The ranges of the various quantities in the experiments were wave height H= 5.9-12.0 cm, wave period T= 1.09s, and water depth h=30 cm. The experiments show that the seabed liquefaction under standing waves, although...... qualitatively similar, show features different from that caused by progressive waves. The pore water pressure builds up (or accumulated) in the areas around the node and subsequently spreads out toward the antinodes. The experimental results imply that this transport is caused by a diffusion mechanism...

GIS-based soil liquefaction susceptibility map of Mumbai city for earthquake events

Science.gov (United States)

Mhaske, Sumedh Yamaji; Choudhury, Deepankar

2010-03-01

The problem of liquefaction of soil during seismic event is one of the important topics in the field of Geotechnical Earthquake Engineering. Liquefaction of soil is generally occurs in loose cohesionless saturated soil when pore water pressure increases suddenly due to induced ground motion and shear strength of soil decreases to zero and leading the structure situated above to undergo a large settlement, or failure. The failures took place due to liquefaction induced soil movement spread over few square km area continuously. Hence this is a problem where spatial variation involves and to represent this spatial variation Geographic Information System (GIS) is very useful in decision making about the area subjected to liquefaction. In this paper, GIS software GRAM++ is used to prepare soil liquefaction susceptibility map for entire Mumbai city in India by marking three zones viz. critically liquefiable soil, moderately liquefiable soil and non liquefiable soil. Extensive field borehole test data for groundwater depth, standard penetration test (SPT) blow counts, dry density, wet density and specific gravity, etc. have been collected from different parts of Mumbai. Simplified procedure of Youd et al. (2001) is used for calculation of factor of safety against soil liquefaction potential. Mumbai city and suburban area are formed by reclaiming lands around seven islands since 1865 till current date and still it is progressing in the area such as Navi Mumbai and beyond Borivali to Mira road suburban area. The factors of safety against soil liquefaction were determined for earthquake moment magnitude ranging from Mw = 5.0 to 7.5. It is found that the areas like Borivali, Malad, Dahisar, Bhandup may prone to liquefaction for earthquake moment magnitude ranging from Mw = 5.0 to 7.5. The liquefaction susceptibility maps were created by using GRAM++ by showing the areas where the factor of safety against the soil liquefaction is less than one. Proposed liquefaction

Bio-char derived from sewage sludge by liquefaction: Characterization and application for dye adsorption

Energy Technology Data Exchange (ETDEWEB)

Leng, Lijian [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Yuan, Xingzhong, E-mail: yxz@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Huang, Huajun [School of Land Resources and Environment, Jiangxi Agricultural University, Nanchang 330045 (China); Shao, Jianguang; Wang, Hou [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China); Chen, Xiaohong [School of Business, Central South University, Changsha 410083 (China); Zeng, Guangming [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environment Biology and Pollution Control, Hunan University, Ministry of Education, Changsha 410082 (China)

2015-08-15

Graphical abstract: - Highlights: • SS liquefaction bio-chars were effective on MG and MB removal from aqueous. • MG adsorption capacity depended strongly on carboxylic and phenolic groups. • Metal release accounted for nearly 30% of the total MG adsorbed on bio-chars. • Acetone and low temperature favor effective adsorbent production by liquefaction. - Abstract: Bio-chars produced by liquefaction of sewage sludge with methanol, ethanol, or acetone as the solvent at 260–380 °C were characterized in terms of their elemental composition, thermogravimetric characteristics, surface area and pore size distribution, and oxygen-containing functional groups composition. The surface area and total volume of the bio-chars were low, but the contents of oxygen-containing functional groups were high. The bio-chars were effective on Malachite green (MG) and Methylene blue (MB) removal from aqueous solution. The MG adsorption equilibrium data showed excellent fit to the Langmuir model and the kinetic data fitted well to the Pseudo-second-order model. Thermodynamic investigations indicated that MG adsorption on bio-char was spontaneous and endothermic. The MG adsorption mechanism appears to be associated with cation release and functional group participation. Additionally, liquefaction of SS with acetone as the solvent at low temperature (280 °C) would favor the production of bio-char adsorbent in terms of bio-char yield and MG and MB adsorption capacity.

Report on the coal liquefaction committee in fiscal 1992; 1992 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-03-01

This paper reports the activities of the coal liquefaction committee in fiscal 1992. The first committee meeting was held on August 21. After having confirmed the minutes of the previous meeting, an explanation was given on the research and development plans in fiscal 1992. The explanation covered the general explanation, bituminous coal liquefaction, brown coal liquefaction, and the common and fundamental aspects. The presented topics included the achievements in the operations using a bituminous coal liquefaction PSU and a small device, the status of compiling the achievements in the brown coal liquefaction project, preparation of the basic policy on developing the common basic technologies, and structuring of a coal liquefaction technology package. The second meeting was held on March 18, 1993. The meeting verified the minutes of the previous meeting, and gave the sub-committee reports for fiscal 1992. The sub-committees include those for bituminous coal liquefaction, brown coal liquefaction, environmental safety evaluation, and separation and refining technologies. As the summary of the achievements in fiscal 1992, descriptions were given on the bituminous coal liquefaction, brown coal liquefaction, and common and basic aspects. The fiscal 1993 plan presented included the budget aspect. A description was given as a topic on the economic performance evaluation and the working scheme (the execution plan) for the brown coal liquefaction process. (NEDO)

Liquefaction of ground tire rubber at low temperature.

Science.gov (United States)

Cheng, Xiangyun; Song, Pan; Zhao, Xinyu; Peng, Zonglin; Wang, Shifeng

2018-01-01

Low-temperature liquefaction has been investigated as a novel method for recycling ground tire rubber (GTR) into liquid using an environmentally benign process. The liquefaction was carried out at different temperatures (140, 160 and 180 °C) over variable time ranges (2-24 h) by blending the GTR with aromatic oil in a range from 0 to 100 parts per hundred rubber (phr). The liquefied GTR was separated into sol (the soluble fraction of rubber which can be extracted with toluene) and gel fractions (the solid fraction obtained after extraction) to evaluate the reclaiming efficiency. It was discovered that the percentage of the sol fraction increased with time, swelling ratio and temperature. Liquefied rubber was obtained with a high sol fraction (68.34 wt%) at 140 °C. Simultaneously, separation of nano-sized carbon black from the rubber networks occurred. The separation of carbon black from the network is the result of significant damage to the cross-linked-network that occurs throughout the liquefaction process. During liquefaction, a competitive reaction between main chain scission and cross-link bond breakage takes place. Copyright © 2017 Elsevier Ltd. All rights reserved.

Japan's New Sunshine Project. 1994 annual summary of coal liquefaction and gasification

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-08-01

This paper summarizes the report for fiscal 1994 on research and development related to coal liquefaction and gasification. In the research and development of coal liquefaction technologies, reports were given on research of liquefaction characteristics of different coals and liquefaction process thereof, and on research of catalysts for the coal liquefaction. In the research and development of coal gasification technologies, reports were given on fundamental studies on gasification characteristics of different coals. In the research and development of liquefaction technologies for bituminous coal, reports were given on design, construction and operation of a bituminous coal liquefaction pilot plant with a capacity of 150 t/d, and the operation supporting studies on the pilot plant. In the fundamental research on the coal liquefaction process, reports were given on refining technologies and utilization of the refined materials, and studies on environment preservation in applying the coal liquefaction technologies. In the research on hydrogen manufacturing technologies by using the fundamental coal technology, reports were given on design, construction and operational studies of a pilot plant. In the research and development of the coal gasification technologies, reports were given on development of a jet-flow gasified coal electric power plant, selection of coals, and development of a data processing system. (NEDO)

Post-liquefaction soil-structure interaction for buried structures: Sensitivity analysis studies

International Nuclear Information System (INIS)

Pires, J.A.; Ang, H.S.; Katayama, I.; Satoh, M.

1993-01-01

The post liquefaction behavior of buried conduits is analyzed and sensitivity analysis is conducted to investigate the damage potential of the forces induced in the buried lifelines following seismically induced liquefaction of the surrounding soil. Various lifeline configurations and loading conditions are considered. The loading conditions considered are: buoyancy forces and permanent ground displacements parallel to the lifeline axis. Pertinent parameters for the soil-lifeline interaction following liquefaction are identified. (author)

Cooperative research in coal liquefaction. Technical progress report, May 1, 1993--April 30, 1994

Energy Technology Data Exchange (ETDEWEB)

Huffman, G.P. [ed.

1994-10-01

Accomplishments for the past year are presented for the following tasks: coliquefaction of coal with waste materials; catalysts for coal liquefaction to clean transportation fuels; fundamental research in coal liquefaction; and in situ analytical techniques for coal liquefaction and coal liquefaction catalysts some of the highlights are: very promising results have been obtained from the liquefaction of plastics, rubber tires, paper and other wastes, and the coliquefaction of wastes with coal; a number of water soluble coal liquefaction catalysts, iron, cobalt, nickel and molybdenum, have been comparatively tested; mossbauer spectroscopy, XAFS spectroscopy, TEM and XPS have been used to characterize a variety of catalysts and other samples from numerous consortium and DOE liquefaction projects and in situ ESR measurements of the free radical density have been conducted at temperatures from 100 to 600{degrees}C and H{sub 2} pressures up to 600 psi.

Probabilistic liquefaction hazard analysis at liquefied sites of 1956 Dunaharaszti earthquake, in Hungary

Science.gov (United States)

Győri, Erzsébet; Gráczer, Zoltán; Tóth, László; Bán, Zoltán; Horváth, Tibor

2017-04-01

Liquefaction potential evaluations are generally made to assess the hazard from specific scenario earthquakes. These evaluations may estimate the potential in a binary fashion (yes/no), define a factor of safety or predict the probability of liquefaction given a scenario event. Usually the level of ground shaking is obtained from the results of PSHA. Although it is determined probabilistically, a single level of ground shaking is selected and used within the liquefaction potential evaluation. In contrary, the fully probabilistic liquefaction potential assessment methods provide a complete picture of liquefaction hazard, namely taking into account the joint probability distribution of PGA and magnitude of earthquake scenarios; both of which are key inputs in the stress-based simplified methods. Kramer and Mayfield (2007) has developed a fully probabilistic liquefaction potential evaluation method using a performance-based earthquake engineering (PBEE) framework. The results of the procedure are the direct estimate of the return period of liquefaction and the liquefaction hazard curves in function of depth. The method combines the disaggregation matrices computed for different exceedance frequencies during probabilistic seismic hazard analysis with one of the recent models for the conditional probability of liquefaction. We have developed a software for the assessment of performance-based liquefaction triggering on the basis of Kramer and Mayfield method. Originally the SPT based probabilistic method of Cetin et al. (2004) was built-in into the procedure of Kramer and Mayfield to compute the conditional probability however there is no professional consensus about its applicability. Therefore we have included not only Cetin's method but Idriss and Boulanger (2012) SPT based moreover Boulanger and Idriss (2014) CPT based procedures into our computer program. In 1956, a damaging earthquake of magnitude 5.6 occurred in Dunaharaszti, in Hungary. Its epicenter was located

Quaternary Geology and Liquefaction Susceptibility, Napa, California 1:100,000 Quadrangle: A Digital Database

Science.gov (United States)

Sowers, Janet M.; Noller, Jay S.; Lettis, William R.

1998-01-01

Earthquake-induced ground failures such as liquefaction have historically brought loss of life and damage to property and infrastructure. Observations of the effects of historical large-magnitude earthquakes show that the distribution of liquefaction phenomena is not random. Liquefaction is restricted to areas underlain by loose, cohesionless sands and silts that are saturated with water. These areas can be delineated on the basis of thorough geologic, geomorphic, and hydrologic mapping and map analysis (Tinsley and Holzer, 1990; Youd and Perkins, 1987). Once potential liquefaction zones are delineated, appropriate public and private agencies can prepare for and mitigate seismic hazard in these zones. In this study, we create a liquefaction susceptibility map of the Napa 1:100,000 quadrangle using Quaternary geologic mapping, analysis of historical liquefaction information, groundwater data, and data from other studies. The study is atterned after state-of-the-art studies by Youd (1973) Dupre and Tinsley (1980) and Dupre (1990) in the Monterey-Santa Cruz area, Tinsley and others (1985) in the Los Angeles area, and Youd and Perkins (1987) in San Mateo County, California. The study area comprises the northern San Francisco Metropolitan Area, including the cities of Santa Rosa, Vallejo, Napa, Novato, Martinez, and Fairfield (Figure 1). Holocene estuarine deposits, Holocene stream deposits, eolian sands, and artificial fill are widely present in the region (Helley and Lajoie, 1979) and are the geologic materials of greatest concern. Six major faults capable of producing large earthquakes cross the study area, including the San Andreas, Rodgers Creek, Hayward, West Napa, Concord, and Green Valley faults (Figure 1).

Preliminary study of soil liquefaction hazard at Terengganu shoreline, Peninsular Malaysia

Science.gov (United States)

Hashim, H.; Suhatril, M.; Hashim, R.

2017-06-01

Terengganu is a shoreline state located in Peninsular Malaysia which is a growing hub for port industries and tourism centre. The northern part offers pristine settings of a relax beach areas whereas the southern part are observed to be a growing centre for development. The serious erosion on soil deposit along the beach line presents vulnerable soil condition to soil liquefaction consists of sandy with low plasticity and shallow ground water. Moreover, local earthquake from nearby fault have present significant tremors over the past few years which need to be considered in the land usage or future development in catering the seismic loading. Liquefaction analysis based on field standard penetration of soil is applied on 546 boreholes scattered along the shoreline areas ranging 244 km of shoreline stretch. Based on simplified approach, it is found that more than 70% of the studied areas pose high liquefaction potential since there are saturated loose sand and silt deposits layer ranges at depth 3 m and up to 20 m. The presence of clay deposits and hard stratum at the remaining 30% of the studied areas shows good resistance to soil liquefaction hence making the area less significant to liquefaction hazard. Result indicates that liquefaction improving technique is advisable in future development of shoreline areas of Terengganu state.

Technology for advanced liquefaction processes: Coal/waste coprocessing studies

Energy Technology Data Exchange (ETDEWEB)

Cugini, A.V.; Rothenberger, K.S.; Ciocco, M.V. [Pittsburgh Energy Technology Center, PA (United States)] [and others

1995-12-31

The efforts in this project are directed toward three areas: (1) novel catalyst (supported and unsupported) research and development, (2) study and optimization of major operating parameters (specifically pressure), and (3) coal/waste coprocessing. The novel catalyst research and development activity has involved testing supported catalysts, dispersed catalysts, and use of catalyst testing units to investigate the effects of operating parameters (the second area) with both supported and unsupported catalysts. Several supported catalysts were tested in a simulated first stage coal liquefaction application at 404{degrees}C during this performance period. A Ni-Mo hydrous titanate catalyst on an Amocat support prepared by Sandia National laboratories was tested. Other baseline experiments using AO-60 and Amocat, both Ni-Mo/Al{sub 2}O{sub 3} supported catalysts, were also made. These experiments were short duration (approximately 12 days) and monitored the initial activity of the catalysts. The results of these tests indicate that the Sandia catalyst performed as well as the commercially prepared catalysts. Future tests are planned with other Sandia preparations. The dispersed catalysts tested include sulfated iron oxide, Bayferrox iron oxide (iron oxide from Miles, Inc.), and Bailey iron oxide (micronized iron oxide from Bailey, Inc.). The effects of space velocity, temperature, and solvent-to-coal ratio on coal liquefaction activity with the dispersed catalysts were investigated. A comparison of the coal liquefaction activity of these catalysts relative to iron catalysts tested earlier, including FeOOH-impregnated coal, was made. These studies are discussed.

High titer ethanol production from SPORL-pretreated lodgepole pine by simultaneous enzymatic saccharification and combined fermentation.

Science.gov (United States)

Lan, T Q; Gleisner, Roland; Zhu, J Y; Dien, Bruce S; Hector, Ronald E

2013-01-01

Lodgepole wood chips were pretreated by sulfite pretreatment to overcome recalcitrance of lignocelluloses (SPORL) at 25% solids loading and 180 °C for 20 min with sulfuric acid and sodium bisulfite charges of 2.2 and 8 wt/wt% on an oven-dry wood basis, respectively. The pretreated wood chips were disk-milled with pretreatment spent liquor and water, and the solid fraction was separated from the liquor stream. The liquor was neutralized and concentrated through vacuum evaporation. Quasi-simultaneous enzymatic saccharification of the cellulosic solids and combined fermentation with the concentrated liquor was conducted at up to 20% total solids loading. Fed-batching of the solids facilitated liquefaction and saccharification, as well as managing instantaneous inhibitor concentrations. At a commercial cellulase (CTec2) loading of only 9 FPU or 0.06 mL/g untreated wood, a maximum ethanol titer of 47.4 g/L was achieved, resulting in a calculated yield of 285 L/tonne of wood using Saccharomyces cerevisiae YRH400 at 35 °C and pH 5.5. Published by Elsevier Ltd.

Comparison of the sand liquefaction estimated based on codes and practical earthquake damage phenomena

Science.gov (United States)

Fang, Yi; Huang, Yahong

2017-12-01

Conducting sand liquefaction estimated based on codes is the important content of the geotechnical design. However, the result, sometimes, fails to conform to the practical earthquake damages. Based on the damage of Tangshan earthquake and engineering geological conditions, three typical sites are chosen. Moreover, the sand liquefaction probability was evaluated on the three sites by using the method in the Code for Seismic Design of Buildings and the results were compared with the sand liquefaction phenomenon in the earthquake. The result shows that the difference between sand liquefaction estimated based on codes and the practical earthquake damage is mainly attributed to the following two aspects: The primary reasons include disparity between seismic fortification intensity and practical seismic oscillation, changes of groundwater level, thickness of overlying non-liquefied soil layer, local site effect and personal error. Meanwhile, although the judgment methods in the codes exhibit certain universality, they are another reason causing the above difference due to the limitation of basic data and the qualitative anomaly of the judgment formulas.

Biomass Indirect Liquefaction Strategy Workshop Summary Report

Energy Technology Data Exchange (ETDEWEB)

none,

2014-07-01

This report is based on the proceedings of the U.S. Department of Energy Bioenergy Technologies Office Biomass Indirect Liquefaction Strategy Workshop. The workshop, held March 20–21, 2014, in Golden, Colorado, discussed and detailed the research and development needs for biomass indirect liquefaction. Discussions focused on pathways that convert biomass-based syngas (or any carbon monoxide, hydrogen gaseous stream) to liquid intermediates (alcohols or acids) and further synthesize those intermediates to liquid hydrocarbons that are compatible as either a refinery feed or neat fuel.

Co-liquefaction of Elbistan Lignite with Manure Biomass; Part 2 - Effect of Biomass Type, Waste to Lignite Ratio and Solid to Liquid Ratio

Science.gov (United States)

Karaca, Hüseyin; Koyunoglu, Cemil

2017-12-01

Most coal hydrogenation processes require a large quantity of hydrogen. In general, a coal derived liquid such as anthracene oil was used as a hydrogen donor solvent. Tetralin, partially hydrogenated pyrene, phenantrene and coal-derived solvents, which contain hydroaromatic compounds, are efficient solvents to donate hydrogen. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. This must be hydrogenated during or before the process and recycled. To reduce the cost of hydrogen donor vehicles instead of liquids recycled from the liquefaction process or several biomass types, industrial by products, liquid fractions derived from oil sands bitumen were successfully used to solubilize a coal from the past. In an attempt to reduce the high cost of hydrogen, part of the hydrogen was replaced by a low cost hydrogen donor solvent. However, when hydrogen is supplied from the hydroaromatic structures present in the solvent, the activity of coal minerals is too low to rehydrogenate the solvent in-situ. Nevertheless, a decrease of using oxygen, in addition to enhanced usage of the hydrogen supply by using various waste materials might lead to a decrease of the cost of the liquefaction procedure. So instead of using tetralin another feeding material such as biomass is becoming another solution improving hydrogen donor substances. Most of the liquefaction process were carried out in a batch reactor, in which the residence time of the liquefaction products is long enough to favour the retrogressive reactions, early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Early studies which are related to liquefaction of coal with biomass generally focus on the synergetic effects of coal while biomass added. Alternatively, to understand the hydrogen transfer from biomass to coal, in this study, Elbistan Lignite (EL) with manure, tea

Simultaneous production of biocrude oil and recovery of nutrients and metals from human feces via hydrothermal liquefaction

International Nuclear Information System (INIS)

Lu, Jianwen; Zhang, Jiaren; Zhu, Zhangbing; Zhang, Yuanhui; Zhao, Yu; Li, Ruirui; Watson, Jamison; Li, Baoming; Liu, Zhidan

2017-01-01

Highlights: • Fast degradation of human waste and energy recovery via hydrothermal liquefaction. • Biocrude, nutrients and metals in human waste are physically separated via HTL. • Max. liquefied fraction was 87.89%, and highest biocrude yield was 34.44% • HTL is promising for treatment from human wastes, and other wet biowastes. - Abstract: Hydrothermal liquefaction (HTL) is a thermochemical process specifically suitable for treating wet wastes. This study investigated its potential for the production of biocrude oil and the recovery of nutrients and metals from human feces via HTL. Specifically, the effects of temperature (260 °C, 300 °C, 340 °C), retention time (10 min, 30 min, 50 min) and total solid (TS) content (5%, 15%, 25%) were studied. The maximum liquefied fraction was 87.89% and the highest biocrude yield reached 34.44% with a higher heating value of 40.29 MJ/kg. Experimental results showed that 54% of carbon in the human feces was migrated to the biocrude oil while 72% of nitrogen was released to the aqueous phase. In addition, most of heavy and alkaline-earth metal elements in the human feces, including Ca (89%), Mg (81%), Al (88%), Fe (72%) and Zn (94%) were distributed in the solid residue, whereas K (89%) and Na (73%) were mainly dissolved into the aqueous phase. This study demonstrated that the efficient degradation of human waste via HTL without any pretreatment and its potential for the valorization in biocrude oil as well as separated nutrients and metals.

EFFECT OF AQUEOUS PRETREATMENT ON PYROLYSIS CHARACTERISTICS OF NAPIER GRASS

Directory of Open Access Journals (Sweden)

ISAH YAKUB MOHAMMED

2015-11-01

Full Text Available Effect of non-catalytic aqueous pretretment on pyrolysis characteristics of Napier grass was investigated using thermogravimetric analyser. Increasing pretreatment severity (0.0-2.0 improved pyrolysis process. The residual mass at the end of pyrolysis for the pretreated sample was about 50% less compared to the untreated sample. Kinetics of the process was evaluated using order based model and both pretreated and untreated samples followed first order reaction. The activation energy of the pretreated samples was similar and higher than that of the raw sample which was attributed to faster rate of decomposition due removal of hetromaterials (ash, extractives and some hemicellulose in the pretreatment stage. Finally, this pretreatment method has demonstrated effectiveness for the removal of pyrolysis retardants and will improve the quantity and quality of bio-oil yield.

Summary of the research achievements in fiscal 1988. Development of coal liquefaction technologies; Sekitan ekika gijutsu kaihatsu. 1988 nendo kenkyu seika no gaiyo

Energy Technology Data Exchange (ETDEWEB)

NONE

1989-03-01

This paper reports the summary of the research and development works in fiscal 1988. The following researches were carried out: as development of a bituminous coal liquefaction technology, studies by using a pilot plant, studies on support of the pilot plant (studies by using an experimental plant (studies by using a 1-t/d PSU, development of an optimal pretreatment technology for coals to be used for liquefaction, studies on improvement in fraction oil distribution in the NEDOL process, and studies by using a 1-t/d plant)), and (studies by using a small device (studies on coal liquefying conditions, and studies on solvent hydrogenation catalysts)). Studies were carried out on operation of the pilot plant, and on support of the pilot plant operation. Materials for auxiliary machinery were developed (including in-plant test of new materials), and so were the devices (including development of a let-down valve) as trial fabrication and development of the plant devices and materials. As coal type selection and survey, coal types were surveyed, and liquefaction performance of Chinese coals was tested. In order to develop applications of coal liquefied products and a refining technology, developments were carried out on up-grading of the coal liquefied oil, a petroleum mixing technology, and a technology to separate hetero compounds in coal liquefied oil, and applications of the compounds. (NEDO)

Use of liquefaction-induced features for paleoseismic analysis - An overview of how seismic liquefaction features can be distinguished from other features and how their regional distribution and properties of source sediment can be used to infer the location and strength of Holocene paleo-earthquakes

Science.gov (United States)

Obermeier, S.F.

1996-01-01

Liquefaction features can be used in many field settings to estimate the recurrence interval and magnitude of strong earthquakes through much of the Holocene. These features include dikes, craters, vented sand, sills, and laterally spreading landslides. The relatively high seismic shaking level required for their formation makes them particularly valuable as records of strong paleo-earthquakes. This state-of-the-art summary for using liquefaction-induced features for paleoseismic interpretation and analysis takes into account both geological and geotechnical engineering perspectives. The driving mechanism for formation of the features is primarily the increased pore-water pressure associated with liquefaction of sand-rich sediment. The role of this mechanism is often supplemented greatly by the direct action of seismic shaking at the ground surface, which strains and breaks the clay-rich cap that lies immediately above the sediment that liquefied. Discussed in the text are the processes involved in formation of the features, as well as their morphology and characteristics in field settings. Whether liquefaction occurs is controlled mainly by sediment grain size, sediment packing, depth to the water table, and strength and duration of seismic shaking. Formation of recognizable features in the field generally requires a low-permeability cap above the sediment that liquefied. Field manifestations are controlled largely by the severity of liquefaction and the thickness and properties of the low-permeability cap. Criteria are presented for determining whether observed sediment deformation in the field originated by seismically induced liquefaction. These criteria have been developed mainly by observing historic effects of liquefaction in varied field settings. The most important criterion is that a seismic liquefaction origin requires widespread, regional development of features around a core area where the effects are most severe. In addition, the features must have a

Catalytic subcritical water liquefaction of flax straw for high yield of furfural

International Nuclear Information System (INIS)

Harry, Inibehe; Ibrahim, Hussameldin; Thring, Ron; Idem, Raphael

2014-01-01

There is substantial interest in the application of biomass as a renewable fuel or for production of chemicals. Flax straw can be converted into valuable chemicals and biofuels via liquefaction in sub-critical water. In this study, the yield of furfural and the kinetics of flax straw liquefaction under sub-critical water conditions were investigated using a high-pressure autoclave reactor. The liquefaction was conducted in the temperature range of 175–325 °C, pressure of 0.1 MPa–8 MPa, retention time in the range of 0 min–120 min, and flax straw mass fraction (w F ) of 5–20 %. Also, the effect of acid catalysts on furfural yield was studied. The kinetic parameters of flax straw liquefaction were determined using nonlinear regression of the experimental data, assuming second-order kinetics. The apparent activation energy was found to be 27.97 kJ mol −1 while the reaction order was 2.0. The optimum condition for furfural yield was at 250 °C, 6.0 MPa, w F of 5% and 0 retention time after reaching set conditions. An acid catalyst was found to selectively favour furfural yield with 40% flax straw conversion. - Highlights: • Flax straw liquefaction in subcritical water. • Creation of a reaction pathway that can be used to optimized furfural production. • Acid catalyst selectively favoured furfural yield with respect to other liquid products. • At the highest process temperature of 325 °C, a carbon conversion of 40% was achieved. • Activation energy and reaction order was 28 kJ/mol and 2.0 respectively

Characteristics estimation of coal liquefaction residue; Sekitan ekika zansa seijo no suisan ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Itonaga, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Okada, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

1996-10-28

The paper studied a possibility of estimating characteristics of coal liquefaction residue from liquefaction conditions in the case of fixing coal kind in the NEDOL process coal liquefaction PSU. Wyoming coal was used for the study, and the already proposed simplified liquefaction reaction models were used. Among material balances explained by the models, those of asphaltene, preasphaltene, THF insoluble matters are concerned with residue composition. Ash content is separately calculated from ash balance. Reaction velocity constants of simplified liquefaction reaction models which influence the residue composition were obtained by the multiple regression method from experimental results in the past. The estimation expression of residue viscosity was introduced from residue ash/composition. When the residue composition is estimated by the model from liquefaction conditions, and the residue viscosity is obtained using it, the higher the liquefaction temperature is, the higher the residue viscosity is. The result obtained well agreed the measuring result. The simplified liquefaction model of a certain coal kind has been established, and characteristics of residue can be estimated even at liquefaction conditions which have never been experienced before if there is a certain amount of the accumulated data on residue composition/characteristics. 4 refs., 4 figs., 4 tabs.

Assessment of wood liquefaction in acidified ethylene glycol using experimental design methodology

Energy Technology Data Exchange (ETDEWEB)

Rezzoug, S.A. [Universite de La Rochelle, Lab. de Maitrise des Technologies Agro-Industrielles, La Rochelle, 17 (France); Capart, R. [Universite de Technologie de Compiegne, Dept. de Genie Chimique, Compiegne, 60 (France)

2003-03-01

The liquefaction of milled wood (Pinus pinaster) was effected in ethylene glycol acidified with small quantities of H{sub 2}SO{sub 4} as catalyst. The purpose of this paper is to evaluate the influence upon the liquefaction yield of the three operating variables, the maximal temperature (150-280 deg C), the reaction time at maximal temperature (20-60 min) and the amount of added H{sub 2}SO{sub 4} (0-1.5% on dry wood). The individual effects, as well as the interactions between operating variables, are investigated by using an experimental design methodology. From a Pareto chart, it appears that the most significant effects are clearly those of the maximum temperature and the interaction between acidity and temperature. Such effects can be graphically verified through response surfaces and contour line plots. From a regression analysis, the conversion rate of wood into liquid is simply expressed as a function of the operating variables by a polynomial containing quadratic terms. A statistical model seems particularly appropriate in the case of complex and multi-components, as wood, a kinetic model is nevertheless proposed for the liquefaction of micro-crystalline cellulose. This model accounts for the formation of a carbonaceous solid residue from the liquid product. Such an unwanted phenomenon obviously results in a lower yield in liquid product. (Author)

Liquefaction behaviors of bamboo residues in a glycerol-based solvent using microwave energy

Science.gov (United States)

Jiulong Xie; Chung-Yun Hse; Todd F. Shupe; Jinqiu Qi; Hui Pan

2014-01-01

Liquefaction of bamboo was performed in glycerol–methanol as co-solvent using microwave energy and was evaluated by characterizing the liquefied residues. High efficiency conversion of bamboo was achieved under mild reaction conditions. Liquefaction temperature and time interacted to affect the liquefaction reaction. Fourier transform infrared analyzes of the residues...

Influence of solvent type on microwave-assisted liquefaction of bamboo

Science.gov (United States)

Jiulong Xie; Chung Hse; Todd F. Shupe; Tingxing Hu

2016-01-01

Microwave-assisted liquefaction of bamboo in glycerol, polyethylene glycerol (PEG), methanol, ethanol, and water were comparatively investigated by evaluating the temperature-dependence for conversion and liquefied residue characteristics. The conversion for the liquefaction in methanol, ethanol, and water increased with an increase in reaction temperature, while that...

Determination of soil liquefaction characteristics by large-scale laboratory tests

International Nuclear Information System (INIS)

1975-05-01

The testing program described in this report was carried out to study the liquefaction behavior of a clean, uniform, medium sand. Horizontal beds of this sand, 42 inches by 90 inches by 4 inches were prepared by pluviation with a special sand spreader, saturated, and tested in a shaking table system designed for this program, which applied a horizontal cyclic shear stress to the specimens. Specimen size was selected to reduce boundary effects as much as possible. Values of pore pressures and shear strains developed during the tests are presented for sand specimens at relative densities of 54, 68, 82, and 90 percent, and the results interpreted to determine the values of the stress ratio causing liquefaction at the various relative densities

Hydrothermal co-liquefaction of microalgae, wood, and sugar beet pulp

NARCIS (Netherlands)

Brilman, D. W.F.; Drabik, N.; Wądrzyk, M.

2017-01-01

Hydrothermal co-liquefaction of mixed (wet and dry) biomass residue streams would greatly enhance the viability and scale up potential of the technology as platform in bioenergy and biorefinery applications. This study aims to identify possible interaction effects between three different feeds

Mars Propellant Liquefaction Modeling in Thermal Desktop

Science.gov (United States)

Desai, Pooja; Hauser, Dan; Sutherlin, Steven

2017-01-01

NASAs current Mars architectures are assuming the production and storage of 23 tons of liquid oxygen on the surface of Mars over a duration of 500+ days. In order to do this in a mass efficient manner, an energy efficient refrigeration system will be required. Based on previous analysis NASA has decided to do all liquefaction in the propulsion vehicle storage tanks. In order to allow for transient Martian environmental effects, a propellant liquefaction and storage system for a Mars Ascent Vehicle (MAV) was modeled using Thermal Desktop. The model consisted of a propellant tank containing a broad area cooling loop heat exchanger integrated with a reverse turbo Brayton cryocooler. Cryocooler sizing and performance modeling was conducted using MAV diurnal heat loads and radiator rejection temperatures predicted from a previous thermal model of the MAV. A system was also sized and modeled using an alternative heat rejection system that relies on a forced convection heat exchanger. Cryocooler mass, input power, and heat rejection for both systems were estimated and compared against sizing based on non-transient sizing estimates.

Liquefaction technology assessment. Final report

Energy Technology Data Exchange (ETDEWEB)

1979-05-01

A survey of coal liquefaction technology and analysis of projected relative performance of high potential candidates has been completed and the results are reported here. The key objectives of the study included preparation of a broad survey of the status of liquefaction processes under development, selection of a limited number of high potential process candidates for further study, and an analysis of the relative commercial potential of these candidates. Procedures which contributed to the achievement of the above key goals included definition of the characteristics and development status of known major liquefaction process candidates, development of standardized procedures for assessing technical, environmental, economic and product characteristics for the separate candidates, and development of procedures for selecting and comparing high potential processes. The comparisons were made for three production areas and four marketing areas of the US. In view of the broad scope of the objectives the survey was a limited effort. It used the experience gained during preparation of seven comprehensive conceptual designs/economic evaluations plus comprehensive reviews of the designs, construction and operation of several pilot plants. Results and conclusions must be viewed in the perspective of the information available, how this information was treated, and the full context of the economic comparison results. Comparative economics are presented as ratios; they are not intended to be predictors of absolute values. Because the true cost of constructing and operating large coal conversion facilities will be known only after commercialization, relative values are considered more appropriate. (LTN)

The effect of wastewater pretreatment on nanofiltration membrane performance

Directory of Open Access Journals (Sweden)

Ali Hashlamon

2017-03-01

Full Text Available Membrane fouling is considered a serious obstacle for operation and cost efficiency in wastewater treatment using nanofiltration (NF. However, pretreatment is the most practical way to reduce this prior to NF. In this research, two types of wastewaters were pretreated with different methods prior to NF to examine the effect of pretreatment on membrane fouling in terms of turbidity, chemical oxygen demand (COD and permeate flux. Turbidity and COD were measured to assess solid foulants and organic species in the wastewater, respectively. The first sample was secondary treated sewage, which was pretreated using coagulation-flocculation-sedimentation (CFS only. Steady flux was increased from 24 L/m2h for wastewater without pretreatment to 32.1 L/m2h with pretreatment. COD was also eliminated after CFS/NF, and turbidity was reduced to 0.6 NTU. The second sample was diluted biodiesel wastewater, which was pretreated using a combination of powdered-activated carbon (PAC adsorption and CFS (PAC/CFS. Steady flux was increased from 22.3 L/m2h for wastewater without pretreatment to 28.7 L/m2h with pretreatment; biodiesel wastewater quality also improved. Turbidity was reduced from 12 to 0.6 NTU, and COD was reduced from 526 to 4 mg/L after NF with PAC/CFS pretreatment, while COD was reduced from 526 to 95 mg/L using NF without pretreatment.

Dynamic behavior of potentially unstable soils and application of model for seismic risk reduction from liquefaction occurrence

International Nuclear Information System (INIS)

Sheshov, Vlatko

2002-11-01

Throughout the last decades, liquefaction phenomenon has been one of the most frequently discussed subjects in geotechnical earthquake engineering. Liquefaction has been a problem arousing considerable attention among the world scientists. The consequences from liquefaction occurrence have been present after each stronger earthquake. We have been witnesses of several strong earthquakes (Kobe - Japan, Chi Chi-Taiwan, Bhuj-India) that have occurred in the last decade. In these earthquakes, the liquefaction phenomenon caused severe damage to structures, loss of their functioning and indirect loss of human lives. Liquefaction as a phenomenon should not arouse fear but should call for serious elaboration and attention instead. The destructive nature of liquefaction could be mitigated, i.e., overcome in two ways: avoiding construction at locations characterized by high liquefaction potential which is not always possible and taking of measures for improvement of foundation soil. Finding out suitable measures for improvement of soil and thus mitigating the liquefaction potential has been the main incentive for the elaboration of this dissertation. The dissipation method involving the use of vertical drains as one of the measures for improvement of soils has been elaborated in details in this scientific work. The doctoral dissertation has been realized through experimental and analytical investigations. The experimental investigations done in the first phase represent model seismic shaking table tests of the efficiency of vertical drains (prefabricated and gravel drains). The analytical investigations in this phase have involved mathematical simulation of the effect of vertical drains upon pore pressure state during the experiments. The second phase of the experimental investigations has involved model tests of the behavior of pile foundations in soils susceptible to liquefaction with installed prefabricated drains. In this phase, the 'p - y' relationships have been

Evaluation of performance of analytical and numerical methods to account for liquefaction effects on the seismic response of anchored quay walls

NARCIS (Netherlands)

van Elsäcker, W.A.; Besseling, F.; Lengkeek, H.J.; Brinkgreve, R.B.J.; de Gijt, J.G.; Jonkman, S.N.

2017-01-01

Liquefaction induced by earthquakes has shown to have potential devastating influence on seismic performance of anchored quay walls. Therefore, measures to mitigate liquefaction are commonly part of the design of quay walls in
seismically active regions. Such mitigation measures are costly.

Hydrogen Transfer during Liquefaction of Elbistan Lignite to Biomass; Total Reaction Transformation Approach

Science.gov (United States)

Koyunoglu, Cemil; Karaca, Hüseyin

2017-12-01

Given the high cost of the tetraline solvent commonly used in liquefaction, the use of manure with EL is an important factor when considering the high cost of using tetraline as a hydrogen transfer source. In addition, due to the another cost factor which is the catalyst prices, red mud (commonly used, produced as a byproduct in the production of aluminium) is reduced cost in the work of liquefaction of coal, biomass, even coal combined biomass, corresponding that making the EL liquefaction an agenda for our country is another important factor. Conditions for liquefaction experiments conducted for hydrogen transfer from manure to coal; Catalyst concentration of 9%, liquid/solid ratio of 3/1, reaction time of 60 min, fertilizer/lignite ratio of 1/3, and the reaction temperature of 400 °C, the stirred speed of 400 rpm and the initial nitrogen pressure of 20 bar was fixed. In order to demonstrate the hydrogen, transfer from manure to coal, coal is used solely, by using tetraline (also known as a hydrogen carrier) and distilled water which is not hydrogen donor as a solvent in the co-liquefaction of experiments, and also the liquefaction conditions are carried out under an inert (N2) gas atmosphere. According to the results of the obtained liquefaction test; using tetraline solvent the total liquid product conversion percentage of the oil + gas conversion was 38.3 %, however, the results of oil+gas conversion obtained using distilled water and EL combined with manure the total liquid product conversion percentage was 7.4 %. According to the results of calorific value and elemental analysis, only the ratio of (H/C)atomic of coal obtained by using tetraline increased with the liquefaction of manure and distilled water. The reason of the increase in the amount of hydrogen due to hydrogen transfer from the manure on the solid surface of the coal, and also on the surface of the inner pore of the coal during the liquefaction, brings about the evaluation of the coal as a

Survey on development of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of literature survey on brown coal liquefaction reactions and elementary techniques. Liquefaction of brown coal in the presence of CO and steam, or CO, H{sub 2} and steam has been investigated. It is not clear by the literature survey whether it is superior to the normal process which uses hydrogen. Brown coal contains moisture at high contents, and the drying techniques are necessary to be developed for its liquefaction. The future coal liquefaction plant will be much larger than the past one, and there are a number of problems to be solved, such as those involved in the designs of large-sized high-pressure slurry pumps, heat exchangers and preheaters. It is also necessary to develop the materials of and production techniques for large reactors which are serviceable under severe conditions. The solid-liquid separation for liquefaction products involves a number of the elementary techniques characteristic of coal liquefaction processes, and needs many technological developments. The one-stage brown coal liquefaction process is compared with the two-stage process for the secondary hydrogenation of SCR, but no clear conclusions are reached. (NEDO)

Production of Advanced Biofuels via Liquefaction - Hydrothermal Liquefaction Reactor Design: April 5, 2013

Energy Technology Data Exchange (ETDEWEB)

Knorr, D.; Lukas, J.; Schoen, P.

2013-11-01

This report provides detailed reactor designs and capital costs, and operating cost estimates for the hydrothermal liquefaction reactor system, used for biomass-to-biofuels conversion, under development at Pacific Northwest National Laboratory. Five cases were developed and the costs associated with all cases ranged from $22 MM/year - $47 MM/year.

Study of initial stage in coal liquefaction. Increase in oil yield with suppression of retrogressive reaction during initial stage; Ekika hanno no shoki katei ni kansuru kenkyu. 1.

Energy Technology Data Exchange (ETDEWEB)

Uesugi, K.; Kanaji, M.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. Ltd., Tokyo (Japan)

1996-10-28

For the coal liquefaction, improvement of liquefaction conditions and increase of liquefied oil yield are expected by suppressing the recombination through rapid stabilization of pyrolytic radicals which are formed at the initial stage of liquefaction. Two-stage liquefaction combining prethermal treatment and liquefaction was performed under various conditions, to investigate the effects of reaction conditions on the yields and properties of products as well as to increase liquefied oil yield. Consequently, it was found that the catalyst contributes greatly to the hydrogen transfer to coal at the prethermal treatment. High yield of n-hexane soluble fraction with products having low condensation degree could be obtained by combining the prethermal treatment in the presence of hydrogen and catalyst with the concentration of slurry after the treatment. This was considered to be caused by the synergetic effect between the improvement of liquefaction by suppressing polymerization/condensation at the initial stage of reaction through the prethermal treatment and the effective hydrogen transfer accompanied with the improvement of contact efficiency of coal/catalyst by the concentration of slurry at the stage of liquefaction. 4 refs., 8 figs.

SHAKING TABLE TEST AND EFFECTIVE STRESS ANALYSIS ON SEISMIC PERFORMANCE WITH SEISMIC ISOLATION RUBBER TO THE INTERMEDIATE PART OF PILE FOUNDATION IN LIQUEFACTION

Science.gov (United States)

Uno, Kunihiko; Otsuka, Hisanori; Mitou, Masaaki

The pile foundation is heavily damaged at the boundary division of the ground types, liquefied ground and non-liquefied ground, during an earthquake and there is a possibility of the collapse of the piles. In this study, we conduct a shaking table test and effective stress analysis of the influence of soil liquefaction and the seismic inertial force exerted on the pile foundation. When the intermediate part of the pile, there is at the boundary division, is subjected to section force, this part increases in size as compared to the pile head in certain instances. Further, we develop a seismic resistance method for a pile foundation in liquefaction using seismic isolation rubber and it is shown the middle part seismic isolation system is very effective.

Low temperature lignocellulose pretreatment: effects and interactions of pretreatment pH are critical for maximizing enzymatic monosaccharide yields from wheat straw

DEFF Research Database (Denmark)

Pedersen, Mads; Johansen, Katja S.; Meyer, Anne S.

2011-01-01

Background: The recent development of improved enzymes and pentose-using yeast for cellulosic ethanol processes calls for new attention to the lignocellulose pretreatment step. This study assessed the influence of pretreatment pH, temperature, and time, and their interactions on the enzymatic...... alkaline pretreatments. Alkaline pretreatments also solubilized most of the lignin. Conclusions: Pretreatment pH exerted significant effects and factor interactions on the enzymatic glucose and xylose releases. Quite extreme pH values were necessary with mild thermal pretreatment strategies (T...... glucose and xylose yields from mildly pretreated wheat straw in multivariate experimental designs of acid and alkaline pretreatments. Results: The pretreatment pH was the most significant factor affecting both the enzymatic glucose and xylose yields after mild thermal pretreatments at maximum 140 degrees...

Effects of Pretreatment Methods on Electrodes and SOFC Performance

Directory of Open Access Journals (Sweden)

Guo-Bin Jung

2014-06-01

Full Text Available Commercially available tapes (anode, electrolyte and paste (cathode were choosen to prepare anode-supported cells for solid oxide fuel cell applications. For both anode-supported cells or electrolyte-supported cells, the anode needs pretreatment to reduce NiO/YSZ to Ni/YSZ to increase its conductivity as well as its catalytic characteristics. In this study, the effects of different pretreatments (open-circuit, closed-circuit on cathode and anodes as well as SOFC performance are investigated. To investigate the influence of closed-circuit pretreatment on the NiO/YSZ anode alone, a Pt cathode is utilized as reference for comparison with the LSM cathode. The characterization of the electrical resistance, AC impedance, and SOFC performance of the resulting electrodes and/or anode-supported cell were carried out. It’s found that the influence of open-circuit pretreatment on the LSM cathode is limited. However, the influence of closed-circuit pretreatment on both the LSM cathode and NiO/YSZ anode and the resulting SOFC performance is profound. The effect of closed-circuit pretreatment on the NiO/YSZ anode is attributed to its change of electronic/pore structure as well as catalytic characteristics. With closed-circuit pretreatment, the SOFC performance improved greatly from the change of LSM cathode (and Pt reference compared to the Ni/YSZ anode.

Liquefaction of solid carbonaceous material with catalyst recycle

Science.gov (United States)

Gupta, Avinash; Greene, Marvin I.

1992-01-01

In the two stage liquefaction of a carbonaceous solid such as coal wherein coal is liquefied in a first stage in the presence of a liquefaction solvent and the first stage effluent is hydrogenated in the presence of a supported hydrogenation catalyst in a second stage, catalyst which has been previously employed in the second stage and comminuted to a particle size distribution equivalent to 100% passing through U.S. 100 Mesh, is passed to the first stage to improve the overall operation.

EARTHQUAKE INDUCED LIQUEFACTION ANALYSIS OF

African Journals Online (AJOL)

liquefaction analysis of Tendaho earth-fill dam, which is part ... sugar cane plantation in an area of 60,000 hectares. The project .... The model is prepared using the QUAKE/W program for the ..... Geo-slope International, Ltd., Canada. Dynamic ...

St. Louis area earthquake hazards mapping project; seismic and liquefaction hazard maps

Science.gov (United States)

Cramer, Chris H.; Bauer, Robert A.; Chung, Jae-won; Rogers, David; Pierce, Larry; Voigt, Vicki; Mitchell, Brad; Gaunt, David; Williams, Robert; Hoffman, David; Hempen, Gregory L.; Steckel, Phyllis; Boyd, Oliver; Watkins, Connor M.; Tucker, Kathleen; McCallister, Natasha

2016-01-01

We present probabilistic and deterministic seismic and liquefaction hazard maps for the densely populated St. Louis metropolitan area that account for the expected effects of surficial geology on earthquake ground shaking. Hazard calculations were based on a map grid of 0.005°, or about every 500 m, and are thus higher in resolution than any earlier studies. To estimate ground motions at the surface of the model (e.g., site amplification), we used a new detailed near‐surface shear‐wave velocity model in a 1D equivalent‐linear response analysis. When compared with the 2014 U.S. Geological Survey (USGS) National Seismic Hazard Model, which uses a uniform firm‐rock‐site condition, the new probabilistic seismic‐hazard estimates document much more variability. Hazard levels for upland sites (consisting of bedrock and weathered bedrock overlain by loess‐covered till and drift deposits), show up to twice the ground‐motion values for peak ground acceleration (PGA), and similar ground‐motion values for 1.0 s spectral acceleration (SA). Probabilistic ground‐motion levels for lowland alluvial floodplain sites (generally the 20–40‐m‐thick modern Mississippi and Missouri River floodplain deposits overlying bedrock) exhibit up to twice the ground‐motion levels for PGA, and up to three times the ground‐motion levels for 1.0 s SA. Liquefaction probability curves were developed from available standard penetration test data assuming typical lowland and upland water table levels. A simplified liquefaction hazard map was created from the 5%‐in‐50‐year probabilistic ground‐shaking model. The liquefaction hazard ranges from low (60% of area expected to liquefy) in the lowlands. Because many transportation routes, power and gas transmission lines, and population centers exist in or on the highly susceptible lowland alluvium, these areas in the St. Louis region are at significant potential risk from seismically induced liquefaction and associated

Subcritical hydrothermal liquefaction of barley straw in fresh water and recycled aqueous phase

DEFF Research Database (Denmark)

Zhu, Zhe; Toor, Saqib; Rosendahl, Lasse

2014-01-01

This project focuses on the investigation of addition of aqueous phase in the production of biofuel from biomass through hydrothermal liquefaction (HTL) technology. Hydrothermal liquefaction is a wet thermal conversion process, which can convert all kinds of biomass to fuels. In this study, barley...... straw was first liquefied in fresh distilled water with the presence of K2CO3 catalyst at 300 C as the reference run. Afterwards, the aqueous phase which is obtained from liquefaction process in the previous run was recycled and used as the reaction medium from the second to the fourth run....... With the addition of recycling aqueous phase in HTL process, it is expected that the amount of the waste water and energy consumption can be reduced. The effect of water recirculation on product yield and properties was investigated in this study. The results showed that bio-oil yield was 34.85 wt% when the barley...

Geological occurrence response to trace elemental migration in coal liquefaction based on SPSS: take no. 11 coalbed in Antaibao mine for example

Science.gov (United States)

Xia, Xiaohong; Qin, Yong; Yang, Weifeng

2013-03-01

Coal liquefaction is an adoptable method to transfer the solid fossil energy into liquid oil in large scale, but the dirty material in which will migrate to different step of liquefaction. The migration rule of some trace elements is response to the react activity of macerals in coal and the geological occurrence of the element nature of itself. In this paper, from the SPSS data correlation analysis and hierarchical clustering dendrogram about the trace elements with macerals respond to coal liquefaction yield, it shows the trace elements in No.11 Antaibao coal seam originated from some of lithophile and sulphophle elements. Correlation coefficient between liquefaction yield of three organic macerals and migration of the elements in liquefaction residue indicated that the lithophile are easy to transfer to residue, while sulphophle are apt to in the liquid products. The activated macerals are response to sulphophle trace elements. The conclusion is useful to the coal blending and environmental effects on coal direct liquefaction.

Thermodynamic Analysis on of Skid-Mounted Coal-bed Methane Liquefaction Device using Cryogenic Turbo-Expander

Science.gov (United States)

Chen, Shuangtao; Niu, Lu; Zeng, Qiang; Li, Xiaojiang; Lou, Fang; Chen, Liang; Hou, Yu

2017-12-01

Coal-bed methane (CBM) reserves are rich in Sinkiang of China, and liquefaction is a critical step for the CBM exploration and utilization. Different from other CBM gas fields in China, CBM distribution in Sinkiang is widespread but scattered, and the pressure, flow-rate and nitrogen content of CBM feed vary significantly. The skid-mounted liquefaction device is suggested as an efficient and economical way to recover methane. Turbo-expander is one of the most important parts which generates the cooling capacity for the cryogenic liquefaction system. Using turbo-expander, more cooling capacity and higher liquefied fraction can be achieved. In this study, skid-mounted CBM liquefaction processes based on Claude cycle are established. Cryogenic turbo-expander with high expansion ratio is employed to improve the efficiency of CBM liquefaction process. The unit power consumption per liquefaction mole flow-rate for CBM feed gas is used as the object function for process optimization, compressor discharge pressure, flow ratio of feed gas to turbo-expander and nitrogen friction are analyzed, and optimum operation range of the liquefaction processes are obtained.

FY 1991 report on the bituminous coal liquefaction section; 1991 nendo rekiseitan ekikabukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

The paper reported activities of the bituminous coal liquefaction section in FY 1991. In the 1st bituminous coal liquefaction section meeting, report/discussion were made on the outline of the plan on the FY 1991 research using pilot plant and the support study of pilot plant. In the 2nd section meeting, report was made on 'How the development of coal liquefaction technology should be in the 21st century,' a report made by the joint section of bituminous coal/brown coal liquefaction. In the 3rd section meeting, report/discussion were made on the state of progress of the FY 1991 R and D and results. In the study using the bituminous coal liquefaction pilot plant, report was made on the outline of construction of a 150t/d pilot plant, study on the acquisition of material balance, analytical study of the data on liquefaction tower, testing survey on properties of coal slurry, and testing survey on slurry preheating furnace. In the support study of pilot plant, report was made on the study using 1t/d PUS, study on the development of the optimum coal refining technology and improvement in the distillate distribution, study of conditions for coal liquefaction and study of solvent hydrogenation catalyst. (NEDO)

Indirect liquefaction of coal. [Coal gasification plus Fischer-Tropsch, methanol or Mobil M-gasoline process

Energy Technology Data Exchange (ETDEWEB)

None

1980-06-30

The most important potential environmental problems uniquely associated with indirect liquefaction appear to be related to the protection of occupational personnel from the toxic and carcinogenic properties of process and waste stream constituents, the potential public health risks from process products, by-products and emissions and the management of potentially hazardous solid wastes. The seriousness of these potential problems is related partially to the severity of potential effects (i.e., human mortality and morbidity), but even more to the uncertainty regarding: (1) the probable chemical characteristics and quantities of process and waste streams; and (2) the effectiveness and efficiencies of control technologies not yet tested on a commercial scale. Based upon current information, it is highly improbable that these potential problems will actually be manifested or pose serious constraints to the development of indirect liquefaction technologies, although their potential severity warrants continued research and evaluation. The siting of indirect liquefaction facilities may be significantly affected by existing federal, state and local regulatory requirements. The possibility of future changes in environmental regulations also represents an area of uncertainty that may develop into constraints for the deployment of indirect liquefaction processes. Out of 20 environmental issues identified as likely candidates for future regulatory action, 13 were reported to have the potential to impact significantly the commercialization of coal synfuel technologies. These issues are listed.

EXPLORATORY RESEARCH ON NOVEL COAL LIQUEFACTION CONCEPT

Energy Technology Data Exchange (ETDEWEB)

Brandes, S.D.; Winschel, R.A.

1998-11-30

The report presents a summary the work performed under DOE Contract No. DE-AC22-95PC95050. Investigations performed under Task 4--Integrated Flow Sheet Testing are detailed. In this program, a novel direct coal liquefaction technology was investigated by CONSOL Inc. with the University of Kentucky Center for Applied Energy Research and LDP Associates. The process concept explored consists of a first-stage coal dissolution step in which the coal is solubilized by hydride ion donation. In the second stage, the products are catalytically upgraded to refinery feedstocks. Integrated first-stage and solids-separation steps were used to prepare feedstocks for second-stage catalytic upgrading. An engineering and economic evaluation was conducted concurrently with experimental work throughout the program. Approaches to reduce costs for a conceptual commercial plant were recommended at the conclusion of Task 3. These approaches were investigated in Task 4. The economic analysis of the process as it was defined at the conclusion of Task 4, indicates that the production of refined product (gasoline) via this novel direct liquefaction technology is higher than the cost associated with conventional two-stage liquefaction technologies.

Advanced liquefaction using coal swelling and catalyst dispersion techniques. Volume 2, appendices. Final technical report, October 1, 1991--September 30, 1994

Energy Technology Data Exchange (ETDEWEB)

Curtis, C.W. [Auburn Univ., AL (United States); Chander, S. [Pennsylvania State Univ., College Park, PA (United States); Gutterman, C.

1995-04-01

Liquefaction experiments were undertaken using subbituminous Black Thunder mine coal to observe the effects of aqueous SO{sub 2} coal beneficiation and the introduction of various coal swelling solvents and catalyst precursors. Aqueous SO{sub 2} beneficiation of Black Thunder coal removed alkali metals and alkaline earth metals, increased the sulfur content and increased the catalytic liquefaction conversion to THF solubles compared to untreated Black Thunder coal. The liquefaction solvent had varying effects on coal conversion, depending upon the type of solvent added. The hydrogen donor solvent, dihydroanthracene, was most effective, while a coal-derived Wilsonville solvent promoted more coal conversion than did relatively inert 1-methylnaphthalene. Swelling of coal with hydrogen bonding solvents tetrahydrofuran (THF), isopropanol, and methanol, prior to reaction resulted in increased noncatalytic conversion of both untreated and SO{sub 2} treated Black Thunder coals, while dimethylsulfoxide (DMSO), which was absorbed more into the coal than any other swelling solvent, was detrimental to coal conversion. Swelling of SO{sub 2} treated coal before liquefaction resulted in the highest coal conversions; however, the untreated coal showed the most improvements in catalytic reactions when swelled in either THF, isopropanol, or methanol prior to liquefaction. The aprotic solvent DMSO was detrimental to coal conversion.

A case study of liquefaction risk analysis based on the thickness and depth of the liquefaction layer using CPT and electric resistivity data in the Hinode area, Itako City, Ibaraki Prefecture, Japan

Science.gov (United States)

Jinguuji, Motoharu; Toprak, Selcuk

2017-12-01

The Hinode area of Itako City in Ibaraki Prefecture, Japan, suffered some of the most severe liquefaction damage of any areas in the Great Eastern Japan Earthquake in 2011. This liquefaction damage has been investigated by Itako City, as well as by universities and research institutes in Japan. The National Institute of Advanced Industrial Science and Technology (AIST) has carried out numerous investigations along the Tone River, and in particular, intensive surveys were done in the Hinode area. We have conducted a risk analysis based on the thickness and depth of the liquefaction layer measured using cone penetration testing (CPT) data and electric resistivity data obtained in the Hinode area. The distribution of the risk estimated from CPT at 143 points, and that obtained from analysis of the resistivity survey data, agreed with the distribution of actual damage. We also carried out conventional risk analyses method using the liquefaction resistance factor (FL) and liquefaction potential index (PL) methods with CPT data. The results show high PL values over the entire area, but their distribution did not agree well with actual damage in some parts of the study area. Because the analysis of the thickness and depth of the liquefaction layer, using geophysical prospecting methods, can cover a widespread area, this method will be very useful in investigating liquefaction risk, especially for gas and water pipelines.

Report on the FY 1998 results of the New Sunshine Project (B version). Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

In 1994, a memorandum on the research cooperation was agreed between NEDO and BPPT (The Agency for the Assessment and Application Technology) in Indonesia, based on the request for the coal liquefaction technology cooperation from BPPT. It includes the following items: conference for professionals to be held, invitation and training of Indonesian engineers, activity for joint field survey and potential survey of location of coal liquefaction commercial plant. Further in 1997, the secondary memorandum was concluded for the potential survey for securing the hydrogen required for coal liquefaction by coal gasification. The survey was summarized as the potential survey for location of coal liquefaction. In the testing study for improving economical efficiency of liquefaction process, it was made clear that the higher the Fe content of Banko coal is, the higher the reaction of liquefaction is, and that Fe compounds in coal show catalysis. In the Soroako area in Sulawesi island, there are the nickel mine run by PT. Inco. Soroako limonite is promising as catalyst material for commercial-scale coal liquefaction. In the gasification method, the plant construction cost increases, but the production amount of coal-derived liquid can be increased. That is more profitable than the production of hydrogen from natural gas. (NEDO)

Effect of multi-stream heat exchanger on performance of natural gas liquefaction with mixed refrigerant

Science.gov (United States)

Chang, Ho-Myung; Lim, Hye Su; Choe, Kun Hyung

2012-12-01

A thermodynamic study is carried out to investigate the effect of multi-stream heat exchanger on the performance of natural gas (NG) liquefaction with mixed refrigerant (MR). A cold stream (low-pressure MR) is in thermal contact with opposite flow of two hot streams (high-pressure MR and NG feed) at the same time. In typical process simulation with commercial software (such as Aspen HYSYS®), the liquefaction performance is estimated with a method of minimum temperature approach, simply assuming that two hot streams have the same temperature. In this study, local energy balance equations are rigorously solved with temperature-dependent properties of MR and NG feed, and are linked to the thermodynamic cycle analysis. The figure of merit (FOM) is quantitatively examined in terms of UA (the product of overall heat transfer coefficient and heat exchange area) between respective streams. In a single-stage MR process, it is concluded that the temperature profile from HYSYS is difficult to realize in practice, and the FOM value from HYSYS is an over-estimate, but can be closely achieved with a proper heat-exchanger design. It is also demonstrated that there exists a unique optimal ratio in three UA's, and no direct heat exchanger between hot streams is recommended.

Analysis of flammability limits for the liquefaction process of oxygen-bearing coal-bed methane

International Nuclear Information System (INIS)

Li, Q.Y.; Wang, L.; Ju, Y.L.

2011-01-01

Highlights: → A novel liquefaction and distillation process is designed for oxygen bearing coal-bed methane. → Oxygen contained in coal-bed methane is removed in distillation process. → Flammability limits are analyzed for the whole operation process. → We find explosion hazard may exist in distillation tower. → Effective measures are proposed to ensure the operation safety in distillation tower. - Abstract: A novel liquefaction and distillation process has been proposed and designed for the typical oxygen-bearing coal-bed methane (CBM), in which the impurities of the oxygen and nitrogen components are removed in the distillation column. The flammability limit theory combining with HYSYS simulation results are employed to analyze and calculate the flammability limits and the results indicate that no flammability hazard exists in the stages of compression, liquefaction and throttling. However, flammability hazard exists at the top the distillation column because the methane mole fraction decreases to the value below the upper flammability limit (UFL). The safety measures of initially removing oxygen content from the feed gas combining with the control of the bottom flowrate (flowrate of the liquid product at column bottom) are proposed to ensure the operation safety of the liquefaction process. The results reveal that the operation safety of the whole process can be guaranteed, together with high methane recovery rate and high purity of the liquid product. The applicability of the liquefaction process has also been analyzed in this paper. The simulation results can offer references for the separation of oxygen from CBM, the analysis of flammability limits and the safety measures for the whole process.

Hydrothermal liquefaction of microalgae's for bio oil production

DEFF Research Database (Denmark)

Toor, Saqib; Reddy, Harvind; Deng, Shuguang

process water for algae cultivation. GC-MS, elemental analyzer, calorimeter and nutrient analysis were used to analyze bio-crude, lipid-extracted algae and water samples produced in the hydrothermal liquefaction process. The highest bio-oil yield of 46% was obtained on Nannochloropsis salina at 310 °C...... and 107 bar. For Spirulina platensis algae sample, the highest bio-oil yield is 38% at 350 °C and 195 bar. Preliminary data also indicate that a lipid-extracted algae solid residue sample obtained in the hydrothermal liquefaction process contains a high level of proteins...

Assessment of Susceptibility to Liquefaction of Saturated Road Embankment Subjected to Dynamic Loads

Science.gov (United States)

Borowiec, Anna; Maciejewski, Krzysztof

2014-03-01

Liquefaction has always been intensely studied in parts of the world where earthquakes occur. However, the seismic activity is not the only possible cause of this phenomenon. It may in fact be triggered by some human activities, such as constructing and mining or by rail and road transport. In the paper a road embankment built across a shallow water reservoir is analyzed in terms of susceptibility to liquefaction. Two types of dynamic loadings are considered: first corresponding to an operation of a vibratory roller and second to an earthquake. In order to evaluate a susceptibility of soil to liquefaction, a factor of safety against triggering of liquefaction is used (FSTriggering). It is defined as a ratio of vertical effective stresses to the shear stresses both varying with time. For the structure considered both stresses are obtained using finite element method program, here Plaxis 2D. The plastic behavior of the cohesionless soils is modeled by means of Hardening Soil (HS) constitutive relationship, implemented in Plaxis software. As the stress tensor varies with time during dynamic excitation, the FSTriggering has to be calculated for some particular moment of time when liquefaction is most likely to occur. For the purposes of this paper it is named a critical time and established for reference point at which the pore pressures were traced in time. As a result a factor of safety distribution throughout embankment is generated. For the modeled structure, cyclic point loads (i.e., vibrating roller) present higher risk than earthquake of magnitude 5.4. Explanation why considered structure is less susceptible to earthquake than typical dam could lay in stabilizing and damping influence of water, acting here on both sides of the slope. Analogical procedure is applied to assess liquefaction susceptibility of the road embankment considered but under earthquake excitation. Only the higher water table is considered as it is the most unfavorable. Additionally the

Conversion of Low-Rank Wyoming Coals into Gasoline by Direct Liquefaction

Energy Technology Data Exchange (ETDEWEB)

Polyakov, Oleg

2013-12-31

Under the cooperative agreement program of DOE and funding from Wyoming State’s Clean Coal Task Force, Western Research Institute and Thermosolv LLC studied the direct conversion of Wyoming coals and coal-lignin mixed feeds into liquid fuels in conditions highly relevant to practice. During the Phase I, catalytic direct liquefaction of sub-bituminous Wyoming coals was investigated. The process conditions and catalysts were identified that lead to a significant increase of desirable oil fraction in the products. The Phase II work focused on systematic study of solvothermal depolymerization (STD) and direct liquefaction (DCL) of carbonaceous feedstocks. The effect of the reaction conditions (the nature of solvent, solvent/lignin ratio, temperature, pressure, heating rate, and residence time) on STD was investigated. The effect of a number of various additives (including lignin, model lignin compounds, lignin-derivable chemicals, and inorganic radical initiators), solvents, and catalysts on DCL has been studied. Although a significant progress has been achieved in developing solvothermal depolymerization, the side reactions – formation of considerable amounts of char and gaseous products – as well as other drawbacks do not render aqueous media as the most appropriate choice for commercial implementation of STD for processing coals and lignins. The trends and effects discovered in DCL point at the specific features of liquefaction mechanism that are currently underutilized yet could be exploited to intensify the process. A judicious choice of catalysts, solvents, and additives might enable practical and economically efficient direct conversion of Wyoming coals into liquid fuels.

Liquefaction of Lignocellulose in Fractionated Light Bio-Oil: Proof of Concept and Techno-Economic Assessment

NARCIS (Netherlands)

Kumar, S.; Lange, Jean Paul; van Rossum, G.; Kersten, Sascha R.A.

2015-01-01

The direct thermal liquefaction of lignocellulose can provide a biocrude that could be used as a precursor for biofuels. However, earlier attempts to use the whole reactor effluent as a liquefaction medium, by recycling it to the liquefaction reactor, were hampered by the buildup of heavy products.

Research on mechanism of and catalysts for extraction liquefaction of coal using coal-based solvents; Sekitankei yozai ni yoru sekitan no chushutsu ekika kiko to shokubai no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-07-01

Papers of Professor Yoshio Kamiya of Tokyo University are compiled into this report. The list of the papers includes (1) Synthesis of heavy fuel oils from coal; (2) Research and development of coal liquefaction; (3) Dissolution reaction of coal by hydrogen-donating aromatic solvents (I); (4) Effect of hydrogen-donor solvent on the liquefaction of coal; (5) Recent studies on the chemical structure of solvent refined coal; (6) Dissolution reaction of coal by hydrogen-donating aromatic solvents (II); (7) Future of coal as energy material; (8), (9), (10) same as (6) in the subject discussed; (11) Recent studies on coal liquefaction catalysts; (12) Environmental problems and drain treatment to accompany processes of converting fossil resources into fuels; (13) Chemistry of coal oxidation; (14) Fractionation and analysis of solvent refined coal by gel permeation chromatography; (15) Current state of research and development of coal liquefaction; (16) Properties and components of coal oils from coal liquefaction processes under development; (17) Solvent effect of coal derived aromatic compounds on the liquefaction of Akabira coal; (18) Chemistry of coal liquefaction; (19) Research and development of coal liquefaction in the U.S.; (20) Thermal treatment of coal-related aromatic ethers in tetralin solution; (21) Recent technology of utilizing heavy carbon resources; (22) Chemical properties and reactivity of coal; (23) Current state and future of development of coal liquefaction processes; and (24) Development of overseas coal liquefaction projects. (NEDO)

Retesting of liquefaction and nonliquefaction case histories from the 1976 Tangshan earthquake

Science.gov (United States)

Moss, R.E.S.; Kayen, R.E.; Tong, L.-Y.; Liu, S.-Y.; Cai, G.-J.; Wu, J.

2011-01-01

A field investigation was performed to retest liquefaction and nonliquefaction sites from the 1976 Tangshan earthquake in China. These sites were carefully investigated in 1978 and 1979 by using standard penetration test (SPT) and cone penetration test (CPT) equipment; however, the CPT measurements are obsolete because of the now nonstandard cone that was used at the time. In 2007, a modern cone was mobilized to retest 18 selected sites that are particularly important because of the intense ground shaking they sustained despite their high fines content and/or because the site did not liquefy. Of the sites reinvestigated and carefully reprocessed, 13 were considered accurate representative case histories. Two of the sites that were originally investigated for liquefaction have been reinvestigated for cyclic failure of fine-grained soil and removed from consideration for liquefaction triggering. The most important outcome of these field investigations was the collection of more accurate data for three nonliquefaction sites that experienced intense ground shaking. Data for these three case histories is now included in an area of the liquefaction triggering database that was poorly populated and will help constrain the upper bound of future liquefaction triggering curves. ?? 2011 American Society of Civil Engineers.

Coal liquefaction: A research and development needs assessment: Final report, Volume II

Energy Technology Data Exchange (ETDEWEB)

Schindler, H.D.; Burke, F.P.; Chao, K.C.; Davis, B.H.; Gorbaty, M.L.; Klier, K.; Kruse, C.W.; Larsen, J.W.; Lumpkin, R.E.; McIlwain, M.E.; Wender, I.; Stewart, N.

1989-03-01

Volume II of this report on an assessment of research needs for coal liquefaction contains reviews of the five liquefaction technologies---direct, indirect, pyrolysis, coprocessing, and bioconversion. These reviews are not meant to be encyclopedic; several outstanding reviews of liquefaction have appeared in recent years and the reader is referred to these whenever applicable. Instead, these chapters contain reviews of selected topics that serve to support the panel's recommendations or to illustrate recent accomplishments, work in progress, or areas of major research interest. At the beginning of each of these chapters is a brief introduction and a summary of the most important research recommendations brought out during the panel discussions and supported by the material presented in the review. A review of liquefaction developments outside the US is included. 594 refs., 100 figs., 60 tabs.

Experimental validation of a mathematical model for seabed liquefaction in waves

DEFF Research Database (Denmark)

Sumer, B. Mutlu; Kirca, Özgür; Fredsøe, Jørgen

2011-01-01

This paper summarizes the results of an experimental study directed towards the validation of a mathematical model for the buildup of pore water pressure and resulting liquefaction of marine soils under progressive waves. Experiments were conducted under controlled conditions with silt ( d50 = 0.......070 mm) in a wave flume with a soil pit. Waves with wave heights in the range 7.7-18 cm with the water depth 55 cm and the wave period 1.6 s enabled us to study both the liquefaction and no-liquefaction regime pore water pressure buildup. The experimental data was used to validate the model. A numerical...

Shear wave velocity-based evaluation and design of stone column improved ground for liquefaction mitigation

Science.gov (United States)

Zhou, Yanguo; Sun, Zhengbo; Chen, Jie; Chen, Yunmin; Chen, Renpeng

2017-04-01

The evaluation and design of stone column improvement ground for liquefaction mitigation is a challenging issue for the state of practice. In this paper, a shear wave velocity-based approach is proposed based on the well-defined correlations of liquefaction resistance (CRR)-shear wave velocity ( V s)-void ratio ( e) of sandy soils, and the values of parameters in this approach are recommended for preliminary design purpose when site specific values are not available. The detailed procedures of pre- and post-improvement liquefaction evaluations and stone column design are given. According to this approach, the required level of ground improvement will be met once the target V s of soil is raised high enough (i.e., no less than the critical velocity) to resist the given earthquake loading according to the CRR- V s relationship, and then this requirement is transferred to the control of target void ratio (i.e., the critical e) according to the V s- e relationship. As this approach relies on the densification of the surrounding soil instead of the whole improved ground and is conservative by nature, specific considerations of the densification mechanism and effect are given, and the effects of drainage and reinforcement of stone columns are also discussed. A case study of a thermal power plant in Indonesia is introduced, where the effectiveness of stone column improved ground was evaluated by the proposed V s-based method and compared with the SPT-based evaluation. This improved ground performed well and experienced no liquefaction during subsequent strong earthquakes.

The sequence of sediment behaviour during wave-induced liquefaction

DEFF Research Database (Denmark)

Sumer, B. Mutlu; Hatipoglu, Figen; Fredsøe, Jørgen

2006-01-01

to be in agreement with recent centrifuge wave-tank experiments. As for the final stage of the sequence of processes (formation of ripples), the ripple steepness (normalized with the angle of repose) for sediment with liquefaction history is found to be the same as that in sediment with no liquefaction history.......This paper presents the results of an experimental investigation of the complete sequence of sediment behaviour beneath progressive waves. The sediment was silty with d(50) = 0.060 mm. Two kinds of measurements were carried out: pore-water pressure measurements (across the sediment depth...... of liquefaction and compaction fronts in the sediment and (iii) the characteristics of the orbital motion of the liquefied sediment including the motion of the interface between the water body and the sediment. The ranges of the various quantities in the tests were: wave height, H = 9-17 cm, wave period, T = 1...

Machine learning modelling for predicting soil liquefaction susceptibility

Directory of Open Access Journals (Sweden)

P. Samui

2011-01-01

Full Text Available This study describes two machine learning techniques applied to predict liquefaction susceptibility of soil based on the standard penetration test (SPT data from the 1999 Chi-Chi, Taiwan earthquake. The first machine learning technique which uses Artificial Neural Network (ANN based on multi-layer perceptions (MLP that are trained with Levenberg-Marquardt backpropagation algorithm. The second machine learning technique uses the Support Vector machine (SVM that is firmly based on the theory of statistical learning theory, uses classification technique. ANN and SVM have been developed to predict liquefaction susceptibility using corrected SPT [(N₁₆₀] and cyclic stress ratio (CSR. Further, an attempt has been made to simplify the models, requiring only the two parameters [(N₁₆₀ and peck ground acceleration (a_max/g], for the prediction of liquefaction susceptibility. The developed ANN and SVM models have also been applied to different case histories available globally. The paper also highlights the capability of the SVM over the ANN models.

Assessment of Soil Liquefaction Potential in Defence Housing Authority, Karachi, Pakistan

Directory of Open Access Journals (Sweden)

Sumaira Asif Khan

2017-04-01

Full Text Available The occurrence of liquefaction phenomenon may be induced in the event of a large magnitude earthquake but sometimes loose, saturated and poorly graded sand may be subjected to liquefaction due to the vibration produced by other sources. Liquefaction could cause damage to building and infrastructure due to sudden increase of pore pressure in the loose layers of saturated sand causing the loss of bearing capacity and shear strength. Defence Housing Authority (DHA is the well planned residential scheme established by Pakistan Army along the coastal belt of Karachi. The soil occurring in DHA is fine grained, poorly graded and mainly comprises of sandy silt and silty sand of Recent age, where water table is encountered at very shallow depth. Hence, it is important to assess the geotechnical behavior of the soil in DHA area, where most of the high rise buildings and mega civil structures are being constructed. In present study, seismic soil liquefaction was evaluated at 15 sites (30 bore holes in DHA by using simplified empirical method in terms of Factor of Safety (FS. The Relative Density (RD was determined with the help of Standard Penetration Test (SPT data. Grain size analysis was also carried out on each borehole samples. The results revealed that the DHA area is vulnerable to liquefaction during severe seismic event of magnitude between 6.5 and 7.5 in Karachi.

Mineral catalysis of oil producing reactions in coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Shridharani, K.G.

1983-01-01

This work was concerned primarily with the development of a relatively inexpensive, readily available, high activity catalyst that can be used as a disposable catalyst in coal liquefaction processes. For a fair evaluation of the developmental mineral catalyst (presulfided iron oxide), it was necessary to determine at different stages of this work, whether catalyst inhibition, deactivation or activity was the limiting factor in coal liquefaction catalysis. First, different routes were explored to prepare a high hydrogenation activity, iron-based catalyst. Naphthalene hydrogenation was used as a model reaction to rate the hydrogenation activities of different additives. Presulfiding of iron oxide with H/sub 2/S, under controlled conditions, rendered the highest hydrogenation activity mineral catalyst, which had a hydrogenation activity even greater than that of commercial CoMo/Al/sub 2/O/sub 3/ catalyst sulfided with creosote oil and hydrogen. Sulfiding of CoMo/Al/sub 2/O/sub 3/ catalyst with H/sub 2/S remarkably improved its initial hydrogenation activity. Second, the catalyst inhibition and deactivation during liquefaction were studied. Liquefaction-process solvents contain a number of compounds that can either deactivate or inhibit the hydrogenation activity of a catalyst. Finally, the hydrocracking activity of the presulfided iron oxide catalyst was compared with that of commercial catalysts, CoMo/Al/sub 2/O/sub 3/ and low alumina FCC catalyst.

Size effects on acid bisulfite pretreatment efficiency: multiple product yields in spent liquor and enzymatic digestibility of pretreated solids

Science.gov (United States)

Yalan Liu; Jinwu Wang; Michael P. Wolcott

2017-01-01

Currently, feedstock size effects on chemical pretreatment performance were not clear due to the complexity of the pretreatment process and multiple evaluation standards such as the sugar recovery in spent liquor or enzymatic digestibility. In this study, we evaluated the size effects by various ways: the sugar recovery and coproduct yields in spent liquor, the...

Report on results of R and D of coal liquefaction technology in fiscal 1981; 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu seika setsumeisho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper explains the results of development of coal liquefaction technology under the Sunshine Project in fiscal 1981. In connection with solvent extraction and liquefaction, an 1 t/day experimental plant was completed for bituminous coals and operated continuously for 153 hours. An examination also started for the development of a 250 t/day pilot plant. As the element studies, R and D is in progress on the solvent extraction and liquefaction process, solid-liquid separation, secondary hydrogenation, and plant materials. In brown coals, the construction work of a 50 t/day pilot plant started for the purpose of establishing liquefaction technology for brown coal in Victoria State, Australia, with a part of the equipment manufactured. As the element studies, research was conducted on primary hydrogenation, deliming, secondary hydrogenation, dehydration and catalysts. In solvolysis liquefaction, a short-time concluding liquefaction reaction was continuously performed by a plant of 1 t/day scale. In direct hydro-liquefaction, a 2.4 t/day experimental plant was constructed, with the element studies conducted successively. In other words, researches were carried out by the bench scale plant on liquefaction, solid-liquid separation, iron-based catalysts, catalyst and reutilization, motive force recovery system by hydrohoist, and effect of preheating and deaeration. (NEDO)

Engineering geologic and geotechnical analysis of paleoseismic shaking using liquefaction effects: Field examples

Science.gov (United States)

Green, R.A.; Obermeier, S.F.; Olson, S.M.

2005-01-01

The greatest impediments to the widespread acceptance of back-calculated ground motion characteristics from paleoliquefaction studies typically stem from three uncertainties: (1) the significance of changes in the geotechnical properties of post-liquefied sediments (e.g., "aging" and density changes), (2) the selection of appropriate geotechnical soil indices from individual paleoliquefaction sites, and (3) the methodology for integration of back-calculated results of strength of shaking from individual paleoliquefaction sites into a regional assessment of paleoseismic strength of shaking. Presented herein are two case studies that illustrate the methods outlined by Olson et al. [Engineering Geology, this issue] for addressing these uncertainties. The first case study is for a site near Memphis, Tennessee, wherein cone penetration test data from side-by-side locations, one of liquefaction and the other of no liquefaction, are used to readily discern that the influence of post-liquefaction "aging" and density changes on the measured in situ soil indices is minimal. In the second case study, 12 sites that are at scattered locations in the Wabash Valley and that exhibit paleoliquefaction features are analyzed. The features are first provisionally attributed to the Vincennes Earthquake, which occurred around 6100 years BP, and are used to illustrate our proposed approach for selecting representative soil indices of the liquefied sediments. These indices are used in back-calculating the strength of shaking at the individual sites, the results from which are then incorporated into a regional assessment of the moment magnitude, M, of the Vincennes Earthquake. The regional assessment validated the provisional assumption that the paleoliquefaction features at the scattered sites were induced by the Vincennes Earthquake, in the main, which was determined to have M ??? 7.5. The uncertainties and assumptions used in the assessment are discussed in detail. ?? 2004 Elsevier B

Effective pretreatment of coal for briquetting

Energy Technology Data Exchange (ETDEWEB)

Sunami, Y; Nishioka, K; Sugimoto, Y

1980-01-01

The pretreatment of coal for briquetting is considered in an attempt to improve the quality of the briquets produced. Crushing of coal to obtain a size distribution suitable for close packing was found to be effective in improving coking properties while drying of coal was found to be effective in increasing briquet density. (In Japanese)

Whole Algae Hydrothermal Liquefaction Technology Pathway

Energy Technology Data Exchange (ETDEWEB)

Biddy, Mary J.; Davis, Ryan; Jones, Susanne B.; Zhu, Yunhua

2013-03-31

In support of the Bioenergy Technologies Office, the National Renewable Energy Laboratory (NREL) and the Pacific Northwest National Laboratory (PNNL) are undertaking studies of biomass conversion technologies to hydrocarbon fuels to identify barriers and target research toward reducing conversion costs. Process designs and preliminary economic estimates for each of these pathway cases were developed using rigorous modeling tools (Aspen Plus and Chemcad). These analyses incorporated the best information available at the time of development, including data from recent pilot and bench-scale demonstrations, collaborative industrial and academic partners, and published literature and patents. This pathway case investigates the feasibility of using whole wet microalgae as a feedstock for conversion via hydrothermal liquefaction. Technical barriers and key research needs have been assessed in order for the hydrothermal liquefaction of microalgae to be competitive with petroleum-derived gasoline, diesel and jet range blendstocks.

Subtask 3.3 - Feasibility of Direct Coal Liquefaction in the Modern Economic Climate

Energy Technology Data Exchange (ETDEWEB)

Benjamin Oster; Joshua Strege; Marc Kurz; Anthony Snyder; Melanie Jensen

2009-06-15

Coal liquefaction provides an alternative to petroleum for the production of liquid hydrocarbon-based fuels. There are two main processes to liquefy coal: direct coal liquefaction (DCL) and indirect coal liquefaction (ICL). Because ICL has been demonstrated to a greater extent than DCL, ICL may be viewed as the lower-risk option when it comes to building a coal liquefaction facility. However, a closer look, based on conversion efficiencies and economics, is necessary to determine the optimal technology. This report summarizes historical DCL efforts in the United States, describes the technical challenges facing DCL, overviews Shenhua's current DCL project in China, provides a DCL conceptual cost estimate based on a literature review, and compares the carbon dioxide emissions from a DCL facility to those from an ICL facility.

The Effect of Ultrasound Pretreatment on Poplar Wood Dimensional Stability

Directory of Open Access Journals (Sweden)

Shu Qiu

2016-08-01

Full Text Available Dimensional stability is a key property of wood that significantly affects its applications. The effect of an ultrasound pretreatment on poplar wood (Populous tomentosa dimensional stability was examined. During the pretreatments, wood samples were immersed in distilled water and treated ultrasonically under three different powers and frequencies. The samples were then analyzed by Fourier transform infrared spectroscopy (FTIR and X-ray diffraction (XRD. The chemical transformation of the cell-wall material was studied and then associated with the change of water absorption and the swelling coefficient. The results showed that the water absorption decreased after the ultrasonic pretreatment. The axial and radial swelling coefficients of the pretreated samples decreased, while the tangential swelling coefficients increased. The volumetric swelling coefficient of pretreated specimens fluctuated near 4.48% (the volumetric swelling coefficient of untreated wood. Ultrasonic pretreatment increased the number of hydrophilic groups, such as the hydroxyl, acetyl, and uronic ester groups. Meanwhile, the pretreatment also increased the degree of crystallinity and reduced the available polar groups. These two factors together caused the change of the moisture absorption and the swelling coefficient of the pretreated wood. These conclusions suggest that the ultrasonic pretreatment is a promising method for further chemical modification of wood.

Effect of process parameters on solvolysis liquefaction of Chlorella pyrenoidosa in ethanol–water system and energy evaluation

International Nuclear Information System (INIS)

Peng, Xiaowei; Ma, Xiaoqian; Lin, Yousheng; Wang, Xusheng; Zhang, Xiaoshen; Yang, Cheng

2016-01-01

Highlights: • Microalgae liquefaction in ethanol–water promoted bio-oil yield and property. • There existed synergistic effect between ethanol and water. • Ethanol contributed to deoxygenation and hydrogen-donating for bio-oil. • Net energy ratios of 20% and 40% ethanol were larger than pyrolysis technology. - Abstract: In this work, Chlorella pyrenoidosa was converted into bio-oil via solvolysis liquefaction in sub/supercritical ethanol–water system. The influence of reaction temperature (220–300 °C), retention time (0–120 min), solid/liquid ratio (6.3/75–50.0/75 g/mL) and ethanol content (0–100%) on bio-oil yield and property was investigated. The increase of reaction temperature and retention time both improved the bio-oil yield. The bio-oil yield increased firstly and then decreased when the solid/liquid ratio and ethanol content exceeded 18.8/75 g/mL and 80%, respectively. As the reaction temperature <260 °C and retention time <30 min, a soft and unsticky product was insoluble in dichloromethane (DCM) during the extraction process. The chemical composition of the DCM-insoluble product was analyzed by FTIR (Fourier Transform Infrared Spectrometry). The change tendency of O/C and H/C atomic ratio of bio-oil indicated that the addition of ethanol contributed to deoxygenation and hydrogen-donating for bio-oil, due to the dehydration and decarboxylation reaction. "1H NMR (hydrogen-1 nuclear magnetic resonance) analysis indicated that the main chemical compositions of bio-oil were aliphatic functional groups and heteroatomic functionalities (80.00–83.58%). The addition of ethanol enhanced the transesterification to form more ester. The NER (net energy ratio, the ratio of energy output to energy consumption) of solvolysis liquefaction in ethanol–water system (NER < 1) was less than that of hydrothermal liquefaction in sole water system (NER = 1.29), but the NERs of 20% and 40% ethanol content (NER = 0.91, 0.70 for 20% and 40% ethanol content

Studies of initial stage in coal liquefaction. Effect of prethermal treatment condition with process solvent to increase oil yields; Ekika hanno no shoki katei ni kansuru kenkyu. Sekitan no maeshori joken to yozai koka

Energy Technology Data Exchange (ETDEWEB)

Shindo, T.; Komatsu, N.; Kishimoto, M.; Okui, T.; Kaneko, T.; Shimasaki, K. [Nippon Brown Coal Liquefaction Co. ltd., Tokyo (Japan)

1996-10-28

Process solvent was hydrogenated in the brown coal liquefaction, to investigate the influence of it on the prethermal treatment and liquefaction. Consequently, it was found that the n-hexane soluble (HS) yield was improved. In this study, capacity of hydrogen transfer from solvent during prethermal treatment and effects of catalyst were investigated. Since prethermal treatment in oil was effective for improving the oil yield in the presence of hydrogen/catalyst or high hydrogen-donor solvent, influence of hydrogen-donor performance of solvent or addition of catalyst on the hydrogenation behavior of coal and the characteristics of products during prethermal treatment were investigated in relation to successive liquefaction results. As a result, it was found that the increase of HS yield was due to the acceleration of conversion of THF-insoluble using high hydrogen-donor solvent and/or by adding catalyst. It was also found that the use of high hydrogen-donor solvent and highly active catalyst at the stage of prethermal treatment before the successive liquefaction was effective for improving the HS yield, i.e., liquefied oil yield. 2 refs., 5 figs., 1 tab.

Direct liquefaction of plastics and coprocessing of coal with plastics

Energy Technology Data Exchange (ETDEWEB)

Huffman, G.P.; Feng, Z.; Mahajan, V. [Univ. of Kentucky, Lexington, KY (United States)

1995-12-31

The objectives of this work were to optimize reaction conditions for the direct liquefaction of waste plastics and the coprocessing of coal with waste plastics. In previous work, the direct liquefaction of medium and high density polyethylene (PE), polypropylene (PPE), poly(ethylene terephthalate) (PET), and a mixed plastic waste, and the coliquefaction of these plastics with coals of three different ranks was studied. The results established that a solid acid catalyst (HZSM-5 zeolite) was highly active for the liquefaction of the plastics alone, typically giving oil yields of 80-95% and total conversions of 90-100% at temperatures of 430-450 {degrees}C. In the coliquefaction experiments, 50:50 mixtures of plastic and coal were used with a tetralin solvent (tetralin:solid = 3:2). Using approximately 1% of the HZSM-5 catalyst and a nanoscale iron catalyst, oil yields of 50-70% and total conversion of 80-90% were typical. In the current year, further investigations were conducted of the liquefaction of PE, PPE, and a commingled waste plastic obtained from the American Plastics Council (APC), and the coprocessing of PE, PPE and the APC plastic with Black Thunder subbituminous coal. Several different catalysts were used in these studies.

Case studies on direct liquefaction of low rank Wyoming coal

Energy Technology Data Exchange (ETDEWEB)

Adler, P.; Kramer, S.J.; Poddar, S.K. [Bechtel Corp., San Francisco, CA (United States)

1995-12-31

Previous Studies have developed process designs, costs, and economics for the direct liquefaction of Illinois No. 6 and Wyoming Black Thunder coals at mine-mouth plants. This investigation concerns two case studies related to the liquefaction of Wyoming Black Thunder coal. The first study showed that reducing the coal liquefaction reactor design pressure from 3300 to 1000 psig could reduce the crude oil equivalent price by 2.1 $/bbl provided equivalent performing catalysts can be developed. The second one showed that incentives may exist for locating a facility that liquifies Wyoming coal on the Gulf Coast because of lower construction costs and higher labor productivity. These incentives are dependent upon the relative values of the cost of shipping the coal to the Gulf Coast and the increased product revenues that may be obtained by distributing the liquid products among several nearby refineries.

Bio-crude production from secondary pulp/paper-mill sludge and waste newspaper via co-liquefaction in hot-compressed water

International Nuclear Information System (INIS)

Zhang, Linghong; Champagne, Pascale; Xu, Chunbao

2011-01-01

Co-liquefaction of secondary pulp/paper-mill sludge (solids concentration: 1.6 wt%) and waste newspaper with a total solids concentration of 11.3 wt% was investigated with and without the addition of catalysts in a 75 ml Parr High-Pressure reactor at temperatures of 250-380 o C for 20 min. The yield of heavy oil (HO) without catalyst was between 16.7 and 28.0 wt% within this temperature range, and peaked at 350 o C. The addition of HCO 2 H, FeS, or KOH at 5 wt% of the total solids (on a dry basis) was found to enhance the HO yield at 300 o C, particularly HCO 2 H, which increased the yield of HO from 24.9 to 34.4 wt%. More interestingly, synergistic effects between secondary pulp/paper-mill sludge and waste newspaper were observed in the co-liquefaction operations. For example, the HO yield attained was 26.9 wt% at 300 o C in the co-liquefaction of the mixture of 33 wt% sludge and 67 wt% waste newspaper, and was noted to be 9 wt% and 6 wt% higher than the yields obtained from liquefaction of sludge and waste newspaper alone, respectively. The HOs from liquefaction or co-liquefaction at 300 o C for 20 min exhibited significantly higher energy contents (HHV ≥ 30 MJ/kg), almost doubled those (-tilde 16 MJ/kg) of the original feedstocks.

Simulation and Optimization of an Innovative Dual Mixed Component Refrigerant Cycle (DMRC) for Natural Gas Offshore Liquefaction Plants

International Nuclear Information System (INIS)

SHAHBA, L.A.; Fahmy, M.F.M.

2004-01-01

Simulation and optimization of an innovative liquefaction process used for the LNG production , namely the Dual Mixed Refrigerant Process (DMRC) has been conducted using the HYSYS simulator .This new process is especially suitable for off shore natural gas liquefaction plants. A numerical optimization technique has been used to determine the optimum conditions for Egyptian natural gas feed source. The investigation of the effect of different compositions of the Mixed refrigerants used was conducted. Meanwhile, the investigation of the influence of the temperature of cooling water used was conducted. The best optimum conditions for the DMRC process were determined .The optimum results achieved for the DMRC process revealed that the DMRC process can be successfully applied as a promising technique for off shore natural gas liquefaction plants

Cooperative research in coal liquefaction infratechnology and generic technology development: Final report, October 1, 1985 to December 31, 1986

Energy Technology Data Exchange (ETDEWEB)

Sendlein, L.V.A.

1987-06-29

During the first year of its research program, the Consortium for Fossil Fuel Liquefaction Science has made significant progress in many areas of coal liquefaction and coal structure research. Research topics for which substantial progress has been made include integrated coal structure and liquefaction studies, investigation of differential liquefaction processes, development and application of sophisticated techniques for structural analysis, computer analysis of multivariate data, biodesulfurization of coal, catalysis studies, co-processing of coal and crude oil, coal dissolution and extraction processes, coal depolymerization, determination of the liquefaction characteristics of many US coals for use in a liquefaction database, and completion of a retrospective technology assessment for direct coal liquefaction. These and related topics are discussed in considerably more detail in the remainder of this report. Individual projects are processed separately for the data base.

Post Hoc Analysis of Passive Cavitation Imaging for Classification of Histotripsy-Induced Liquefaction in Vitro.

Science.gov (United States)

Bader, Kenneth B; Haworth, Kevin J; Maxwell, Adam D; Holland, Christy K

2018-01-01

Histotripsy utilizes focused ultrasound to generate bubble clouds for transcutaneous tissue liquefaction. Bubble activity maps are under development to provide image guidance and monitor treatment progress. The aim of this paper was to investigate the feasibility of using plane wave B-mode and passive cavitation images to be used as binary classifiers of histotripsy-induced liquefaction. Prostate tissue phantoms were exposed to histotripsy pulses over a range of pulse durations (5- ) and peak negative pressures (12-23 MPa). Acoustic emissions were recorded during the insonation and beamformed to form passive cavitation images. Plane wave B-mode images were acquired following the insonation to detect the hyperechoic bubble cloud. Phantom samples were sectioned and stained to delineate the liquefaction zone. Correlation between passive cavitation and plane wave B-mode images and the liquefaction zone was assessed using receiver operating characteristic (ROC) curve analysis. Liquefaction of the phantom was observed for all the insonation conditions. The area under the ROC (0.94 versus 0.82), accuracy (0.90 versus 0.83), and sensitivity (0.81 versus 0.49) was greater for passive cavitation images relative to B-mode images ( ) along the azimuth of the liquefaction zone. The specificity was greater than 0.9 for both imaging modalities. These results demonstrate a stronger correlation between histotripsy-induced liquefaction and passive cavitation imaging compared with the plane wave B-mode imaging, albeit with limited passive cavitation image range resolution.

The use of mixed pyrrhotite/pyrite catalysts for co-liquefaction of coal and waste rubber tires

Energy Technology Data Exchange (ETDEWEB)

Dadyburjor, D.B.; Zondlo, J.W.; Sharma, R.K. [West Virginia Univ., Morgantown, WV (United States)] [and others

1995-12-31

The overall objective of this research program is to determine the optimum processing conditions for tire/coal co-liquefaction. The catalysts used will be a ferric-sulfide-based materials, as well as promising catalysts from other consortium laboratories. The intent here is to achieve the maximum coal+tire conversion at the mildest conditions of temperature and pressure. Specific objectives include an investigation of the effects of time, temperature, pressure, catalyst and co-solvent on the conversion and product slate of the co-liquefaction. Accomplishments and conclusions are discussed.

Study on hydrogen transfer in coal liquefaction by tritium and carbon-14 tracers

International Nuclear Information System (INIS)

Nitoh, Osamu; Kabe, Toshiaki; Kabe, Yaeko.

1985-01-01

For the analysis of mechanism of hydrogenation and cracking of coal, the liquefaction of Taiheiyo coal using tritium labeled gaseous hydrogen and tritium labeled tetralin with small amounts of carbon-14 labeled naphthalene has been studied. Taiheiyo coal(25g) was thermally decomposed in tetralin or naphthalene solvent(75g) at 400--440 0 C under the initial hydrogen pressure of 5.9MPa for 30min with Ni-Mo-Al 2 O 3 catalyst(0--5g). The reaction mixture in an autoclave was separated by filtration, distillation and solvent extraction. Produced gas, oils and the solvent were analyzed by gas chromatography. The tritium and carbon-14 contents of separated reaction products were measured with a liquid scintilation counter to study the hydrogen transfer mechanism. The distribution of reaction products and the amount of hydrogen transfer from gas or solvent to the products were also determined. In hydrogen donor solvent such as tetralin, the coal liquefaction yield was independent from the catalyst, but the catalyst was effective in hydrocracking of preasphaltene and asphaltene. In naphthalene solvent, the coal liquefaction reaction hardly occured in the absence of the catalyst, because hydrogen transfer from both the solvent and gaseous hydrogen was scarce. Tritium distribution in the reaction products showed that complicated hydrogen exchange reactions between gaseous hydrogen, coal liquids and solvent came out by the presence of coal liquids and catalyst. The very small amounts of carbon-14 transferred to the liquefaction products showed that carbon exchange or transfer between solvent and coal did not take place. (author)

Report on results for fiscal 1997 (B edition) on development of coal liquefaction technology. Development of bituminous coal liquefaction technology (research by pilot plant) 1/2; 1997 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Rekiseitan ekika gijutsu no kaihatsu (pilot plant ni yoru kenkyu) 2/2

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-06-01

This paper reports the operation of a pilot plant of a bituminous coal liquefaction technology as the 1/2 report. The operation research of the Run-2 through the Run-4-2 was conducted using, as the material, tanitoharum coal which is operating basis coal. The Run-2 achieved a coal charging continuous operation for 42 days. During the operation of 80% slurry supply load, various data were obtained including material balance under the NEDOL standard liquefaction conditions, with a liquefaction yield of 54% daf coal achieved. Steam blowing into the heating tube was found effective as measures to cope with coking generation in the heating furnace of a vacuum distillation tower. The softening point of liquefaction residuals was improved to 178 degrees C through the extracting adjustment of reduced pressure heavy gravity light oil fraction for washing. The Run-3/4-1 achieved a plant load ratio of 100% and a long-term coal charging continuous operation for 80 days, while the Run-3 achieved a slurry supply load of 100% under the NEDOL standard liquefaction conditions. The Run-4-1 achieved a high liquefaction yield of 58wt% daf coal. Performance was confirmed of a neutron beam source irradiation apparatus/measuring system and a tracer injection equipment. (NEDO)

Achievement report for fiscal 1982 on Sunshine Program. Research and development of coal liquefaction technology (Conceptual designs for coal liquefaction pilot plants - Solvent extraction liquefaction process); 1982 nendo sekitan ekika gijutsu no kenkyu kaihatsu seika hokokusho. Sekitan ekika pilot plant no gainen sekkei (yozai chushutsu ekikaho)

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

This research aims to prepare conceptual designs for a 250t/d-class and 500t/d-class coal liquefaction pilot plants based on the achievement of research on solvent extraction liquefaction of coal. It also aims to define the solvent extraction process and provide decision-making material relative to the development and promotion of coal liquefaction technologies in the future. Development started in 1978 of the technology of solvent extraction liquefaction of coal, and a 1t/d PDU (process development unit) was completed in 1981. Studies through its operation have continued for more than 3000 hours already, and technical data are being accumulated steadily. Techniques acquired through operating the 1t/d PDU have been put together, and rough process conditions are established. A rough process result is achieved of the same conditions. In these two respects, the newly developed process is equal to other processes. The phenomena in this process are roughly grasped. It is deemed that, with the existing technique combined with the technique acquired here, a technological level has been reached where conceptual designs of large pilot plants may be worked out for solvent extraction liquefaction of coal. Under the circumstances, with a view to developing a commercial plant whose main products will be fuel oils, conceptual designs are prepared for large pilot plants, and are compiled into this report. (NEDO)

Enhancement of energy performance in a boil-off gas re-liquefaction system of LNG carriers using ejectors

International Nuclear Information System (INIS)

Tan, Hongbo; Zhao, Qingxuan; Sun, Nannan; Li, Yanzhong

2016-01-01

Highlights: • An ejector-enhanced LNG boil-off gas (BOG) re-liquefaction system is proposed. • The new system has an improvement of 28% in COP over the existing system. • The specific energy consumption of the new system is reduced to 0.59 kW h/kg(BOG). • The power consumption of 754.1 kW is saved in the case study. - Abstract: An ejector-enhanced Liquefied Natural Gas (LNG) boil-off gas (BOG) re-liquefaction system is proposed to improve the energy efficiency of the existing system. In the new system, two ejectors are respectively used to reduce the energy loss in the expansion of the pressurized BOG and inject a part of fuel BOG into the compression system, and a recuperator is employed to recover the cold energy of the BOG exited from LNG tank. The performance improvement of the proposed system is analysed on the basis of the simulation in Aspen HYSYS. In the case of the re-liquefaction capacity of 4557.6 kg/h, the coefficient of performance (COP) and exergy efficiency can be increased by 28%, and the specific energy consumption (SEC) reduced from 0.756 to 0.59 kW h/kg(BOG) compared to the conventional BOG re-liquefaction system. Correspondingly, the power consumption of 754.1 kW is saved. This means that applying ejectors can effectively improve the energy efficiency of the existing BOG re-liquefaction system for LNG carriers.

Thermochemical liquefaction characteristics of microalgae in sub- and supercritical ethanol

Energy Technology Data Exchange (ETDEWEB)

You, Qiao; Chen, Liang [College of Environmental Science and Engineering, Hunan University, Changsha (China); Key Laboratory of Environment Biology and Pollution Control, Ministry of Education, Changsha (China)

2011-01-15

Thermochemical liquefaction characteristics of Spirulina, a kind of high-protein microalgae, were investigated with the sub- and supercritical ethanol as solvent in a 1000 mL autoclave. The influences of various liquefaction parameters on the yields of products (bio-oil and residue) from the liquefaction of Spirulina were studied, such as the reaction temperature (T), the S/L ratio (R{sub 1}, solid: Spirulina, liquid: ethanol), the solvent filling ratio (R{sub 2}) and the type and dosage of catalyst. Without catalyst, the bio-oil yields were in the range of 35.4 wt.% and 45.3 wt.% depending on the changes of T, R{sub 1} and R{sub 2}. And the bio-oil yields increased generally with increasing T and R{sub 2}, while the bio-oil yields reduced with increasing R{sub 1}. The FeS catalyst was certified to be an ideal catalyst for the liquefaction of Spirulina microalgae for its advantages on promoting bio-oil production and suppressing the formation of residue. The optimal dosage of catalyst (FeS) was ranging from 5-7 wt.%. The elemental analyses and FT-IR and GC-MS measurements for the bio-oils revealed that the liquid products have much higher heating values than the crude Spirulina sample and fatty acid ethyl ester compounds were dominant in the bio-oils, irrespective of whether catalyst was used. (author)

Activity and selectivity of three molybdenum catalysts for coal liquefaction reactions

Energy Technology Data Exchange (ETDEWEB)

Curtis, C.W.; Pellegrino, J.L.

The activity and selectivity of three different molybdenum catalysts for reactions occurring in coal liquefaction, specifically for hydrogenation (HYD), hydrodeoxygenation (HDO), hydrodenitrogenation (HDN), hydrodesulfurization (HDS), and hydrocracking (HYC), have been examined. The three molybdenum catalysts used were molybdenum napthenate, molybdenum on ..gamma..-alumina, and a precipitated, disordered MoS/sub 2/. Molybdenum naphthenate was most selective for HYD and HDN. All three catalysts exhibited approximately equal activity for HDS and HDO and little selectivity for HYC of alkyl bridge structures. The activity and selectivity of the three molybdenum catalysts for producing hydrocarbons and removing heteroatoms from coal during liquefaction were determined and compared. Molybdenum naphthenate was the most active catalyst for hydrocarbon production and removal of nitrogen- and oxygen-containing species during coal liquefaction. 31 refs., 4 figs., 7 tabs.

Evaluation of liquefaction potential of soil based on standard penetration test using multi-gene genetic programming model

Science.gov (United States)

Muduli, Pradyut; Das, Sarat

2014-06-01

This paper discusses the evaluation of liquefaction potential of soil based on standard penetration test (SPT) dataset using evolutionary artificial intelligence technique, multi-gene genetic programming (MGGP). The liquefaction classification accuracy (94.19%) of the developed liquefaction index (LI) model is found to be better than that of available artificial neural network (ANN) model (88.37%) and at par with the available support vector machine (SVM) model (94.19%) on the basis of the testing data. Further, an empirical equation is presented using MGGP to approximate the unknown limit state function representing the cyclic resistance ratio (CRR) of soil based on developed LI model. Using an independent database of 227 cases, the overall rates of successful prediction of occurrence of liquefaction and non-liquefaction are found to be 87, 86, and 84% by the developed MGGP based model, available ANN and the statistical models, respectively, on the basis of calculated factor of safety (F s) against the liquefaction occurrence.

FY 1980 Report on results of Sunshine Project. Research and development of coal liquefaction techniques (Development of direct hydrogenation type liquefaction plant and researches on liquefaction reactions in the presence of iron-based catalyst); 1980 nendo sekitan ekika gijutsu no kenkyu kaihatsu, chokusetsu suiten ekika plant no kaihatsu seika hokokusho. Tetsukei shokubai ni yoru ekika hanno no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This program is aimed at development of iron-based catalyst suited for direct hydrogenation type coal liquefaction by elucidating the effects of the catalyst on the liquefaction reactions. The iron-based catalyst seems to act as the radical stabilizer rather than the reaction promoter, because the increased quantity of the catalyst and increased H{sub 2} pressure share the common pattern rather than the catalyst enhances the activity, which is associated with increased reaction temperature or residence time. This is more notably observed when the coal species is changed to brown coal. In other words, recombination of the decomposition products by polycondensation is accelerated in the presence of the catalyst in decomposition of brown coal from bituminous coal, with the result that the catalyst effects are more notably observed. Whether this results from difference in age between brown coal and bituminous coal or content of specific types of ashes should be elucidated, because this point is considered to deeply relate to eventual development of the liquefaction reaction system. The FY 1980 program includes the primary screening of different types of iron compounds and tests of some iron-metal-based catalysts. (NEDO)

Report for fiscal 1995 by basic liquefaction technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

Delivered at the 1st meeting are a report on the fiscal 1995 research plan and an interim report, involving the use of coal-derived oils, research on refining technology using a PDU (process developing unit), reforming technology and petroleum blending technology for coal-derived oils, development of new reforming catalysts, technology of heterocompound separation, and the development of applications. Reported in relation with the development of environmentally friendly coal liquefaction technology are the study of coal liquefaction conditions, study of the upgrading of basic liquefaction techniques for the improvement and rationalization of the liquefaction process, and a project of liquefaction technology internationalization. A report is also given on a liquefaction catalyst study meeting. At the 2nd meeting, reports are delivered on the development of environmentally friendly coal liquefaction technology, including a briefing on the situation in general, designing of highly active catalysts, elucidation of the mechanism of emergence of activity, achievement of the marginal yield of coal-derived oils, and the properties of catalyst attached to coal. Delivered in relation with the use of coal-derived oils and technology for their refining are a briefing on the situation in general and reports on the blockup to occur in the naphtha fraction process and measures to counter the problem, control of the metamorphosis of active metals in reaction, heterocompound separation technology, and the development of applications. (NEDO)

Effects of low dose radiation pretreatment on radiation injuried brain's free radicle

International Nuclear Information System (INIS)

Xu Fuqi; Wang Cheng; Xie Hong; Tian Ye

2006-01-01

Objective: To investigate the effect of low dose radiation pretreatment on radiation in- juried brain's free radicle to provide some useful data of brain radiation injury protection. Methods: One hundred mGy was selected as the pretreatment does, 25 Gy was selected as the challenge does. Experiment rats were divided into three groups randomly, group one as simple group:the group irradiated without exposing to pre-irradiation; group two as 6 h-group: the group irradiated with LDR pretreatment 6 h before exposing to 25 Gy irradiation; group three as 24 h-group:the group irradiated with LDR pretreatment 24 h before 25 Gy irradiation. The observation was done 6 hour's after irradiation, the effect of LDR pretreatment on increasing activity of the superoxide dismutase(SOD) and the content of malondialdehyde(MDA) after the brain tissue homogenate were detected. Results: Com- pared with the simple group, the group with LDR pretreatment showed increasing of SOD and decreasing of MDA at the 6th hour after 25Gy irradiation. In addition, there was no difference between the 6 h-group and the 24 h-group. Conclusion: LDR pretreatment can increase SOD and decrease MDA in some period. It could infer that the suitable LDR pretreatment could play a protective role in the brain radiation injury. (authors)

Biomass Direct Liquefaction Options. TechnoEconomic and Life Cycle Assessment

Energy Technology Data Exchange (ETDEWEB)

Tews, Iva J.; Zhu, Yunhua; Drennan, Corinne; Elliott, Douglas C.; Snowden-Swan, Lesley J.; Onarheim, Kristin; Solantausta, Yrjo; Beckman, David

2014-07-31

The purpose of this work was to assess the competitiveness of two biomass to transportation fuel processing routes, which were under development in Finland, the U.S. and elsewhere. Concepts included fast pyrolysis (FP), and hydrothermal liquefaction (HTL), both followed by hydrodeoxygenation, and final product refining. This work was carried out as a collaboration between VTT (Finland), and PNNL (USA). The public funding agents for the work were Tekes in Finland and the Bioenergy Technologies Office of the U.S. Department of Energy. The effort was proposed as an update of the earlier comparative technoeconomic assessment performed by the IEA Bioenergy Direct Biomass Liquefaction Task in the 1980s. New developments in HTL and the upgrading of the HTL biocrude product triggered the interest in reinvestigating this comparison of these biomass liquefaction processes. In addition, developments in FP bio-oil upgrading had provided additional definition of this process option, which could provide an interesting comparison.

Ground motions estimates for a cascadia earthquake from liquefaction evidence

Science.gov (United States)

Dickenson, S.E.; Obermeier, S.F.

1998-01-01

Paleoseismic studies conducted in the coastal regions of the Pacific Northwest in the past decade have revealed evidence of crustal downdropping and subsequent tsunami inundation, attributable to a large earthquake along the Cascadia subduction zone which occurred approximately 300 years ago, and most likely in 1700 AD. In order to characterize the severity of ground motions from this earthquake, we report on results of a field search for seismically induced liquefaction features. The search was made chiefly along the coastal portions of several river valleys in Washington, rivers along the central Oregon coast, as well as on islands in the Columbia River of Oregon and Washington. In this paper we focus only on the results of the Columbia River investigation. Numerous liquefaction features were found in some regions, but not in others. The regional distribution of liquefaction features is evaluated as a function of geologic and geotechnical factors at each site in order to estimate the intensity of ground shaking.

Liquefaction susceptibility of fine-grained soils: preliminary study report. Final report, September 1985-March 1986

Energy Technology Data Exchange (ETDEWEB)

Chang, N.Y.

1987-09-01

Soil liquefaction, a hazardous ground failure induced by strong motion earthquakes, can cause catastrophic damage to structures such as dams, bridges, power plants, and water-front structures and may involve great losses of life. Examples of liquefaction and resulting damage were observed during the Alaska (1964), Niigata, Japan (1964), and Tangshan, China (1976), earthquakes. Ground failure due to earthquake-induced soil liquefaction may manifest itself as excessive settlement, loss of bearing capacity, sand boiling, and flow slides. The liquefaction potential of clean sands has been studied extensively for the last two decades. However, case histories revealed that liquefied sands were seldom clean. They may contain various percentages of silt or clay or both. In fact, the Chinese observation in the Tansghan earthquake indicated that some cohesive soils may have liquefied. If this indeed had happened, then structures underlain by fine-grained soils, with a marginal safety factor based on the liquefaction criteria normally applied to sands, may actually be unsafe. Thus there is an urgent need for establishing new criteria for the liquefaction susceptibility of soils to include those identified as fine-grained. The author, Professor N.Y. Chang of the University of Colorado at Denver, visited several Chinese agencies and and universities in and near Beijing, China, in the summer of 1985 in an attempt to investigate and verify reported data on the liquefaction of cohesive soils during the Tangshan earthquake of 1976 and to negotiate cooperative research into the problem. This report presents the result of supportive literature review and the findings of the China trip.

Motor fuels made by direct liquefaction of coal, peat and biomass. Drivmedel genom direktfoervaetskning av kol, torv och biomassa

Energy Technology Data Exchange (ETDEWEB)

Granath, L; Karlsson, G; Karlsson, G; Nilsson, T

1981-01-01

The Department of Chemical Technology at the Royal Institute of Technology has completed a system study concerning direct liquefaction of peat and biomass to produce transportation fuel. A comprehensive survey of coal liquefaction is included. Gasoline produced in Sweden from direct liquefaction of imported coal may compete with regular gasoline at the earliest around 1985. Biomass can become a competitive alternative to black coal at the beginning of the 21st century. Methanol can be produced from wood with a higher efficiency than the transportation fuels which are produced by direct liquefaction. The peat is not good source for liquefaction as wood chips. A continuously working liquefaction plant designed also for peat among other substances is under construction at the Royal Institute of Technology, Stockholm.

Comparison of oxygen liquefaction methods for use on the Martian surface

Science.gov (United States)

Johnson, W. L.; Hauser, D. M.; Plachta, D. W.; Wang, X.-Y. J.; Banker, B. F.; Desai, P. S.; Stephens, J. R.; Swanger, A. M.

2018-03-01

In order to use oxygen that is produced on the surface of Mars from In-Situ production processes in a chemical propulsion system, the oxygen must first be converted from vapor phase to liquid phase and then stored within the propellant tanks of the propulsions system. There are multiple ways that this can be accomplished, from simply attaching a liquefaction system onto the propellant tanks to carrying separate tanks for liquefaction and storage of the propellant and loading just prior to launch (the way that traditional rocket launches occur on Earth). A study was done into these various methods by which the oxygen (and methane) could be liquefied and stored on the Martian surface. Five different architectures or cycles were considered: Tube-on-Tank (also known as Broad Area Cooling or Distributed Refrigeration), Tube-in-Tank (also known as Integrated Refrigeration and Storage), a modified Linde open liquefaction/refrigeration cycle, the direct mounting of a pulse tube cryocooler onto the tank, and an in-line liquefier at ambient pressure. Models of each architecture were developed to give insight into the performance and losses of each of the options. The results were then compared across eight categories: Mass, Power (both input and heat rejection), Operability, Cost, Manufacturability, Reliability, Volume-ility, and Scalability. The result was that Tube-on-Tank and Tube-in-Tank architectures were the most attractive solutions, with NASA's engineering management choosing to pursue tube on tank development rather than further differentiate the two. As a result NASA is focusing its Martian surface liquefaction activities and technology development on Tube-on-Tank liquefaction cycles.

Quantitative characterization of the aqueous fraction from hydrothermal liquefaction of algae

Energy Technology Data Exchange (ETDEWEB)

Maddi, Balakrishna; Panisko, Ellen; Wietsma, Thomas; Lemmon, Teresa; Swita, Marie; Albrecht, Karl; Howe, Daniel

2016-10-01

Aqueous streams generated from hydrothermal liquefaction contain approximately 30% of the total carbon present from the algal feed. Hence, this aqueous carbon must be utilized to produce liquid fuels and/or specialty chemicals for economic sustainability of hydrothermal liquefaction on industrial scale. In this study, aqueous fractions produced from the hydrothermal liquefaction of fresh water and saline water algal cultures were analyzed using a wide variety of analytical instruments to determine their compositional characteristics. This study will also inform researchers designing catalysts for down-stream processing such as high-pressure catalytic conversion of organics in aqueous phase, catalytic hydrothermal gasification, and biological conversions. Organic chemical compounds present in all eight aqueous fractions were identified using two-dimensional gas chromatography equipped with time-of-flight mass spectrometry. Identified compounds include organic acids, nitrogen compounds and aldehydes/ketones. Conventional gas chromatography and liquid chromatography methods were utilized to quantify the identified compounds. Inorganic species in the aqueous stream of hydrothermal liquefaction of algae were identified using ion chromatography and inductively coupled plasma optical emission spectrometer. The concentrations of organic chemical compounds and inorganic species are reported. The amount quantified carbon ranged from 45 to 72 % of total carbon in the aqueous fractions.

Effect of alkaline microwaving pretreatment on anaerobic digestion and biogas production of swine manure.

Science.gov (United States)

Yu, Tao; Deng, Yihuan; Liu, Hongyu; Yang, Chunping; Wu, Bingwen; Zeng, Guangming; Lu, Li; Nishimura, Fumitake

2017-05-10

Microwave assisted with alkaline (MW-A) condition was applied in the pretreatment of swine manure, and the effect of the pretreatment on anaerobic treatment and biogas production was evaluated in this study. The two main microwaving (MW) parameters, microwaving power and reaction time, were optimized for the pretreatment. Response surface methodology (RSM) was used to investigate the effect of alkaline microwaving process for manure pretreatment at various values of pH and energy input. Results showed that the manure disintegration degree was maximized of 63.91% at energy input of 54 J/g and pH of 12.0, and variance analysis indicated that pH value played a more important role in the pretreatment than in energy input. Anaerobic digestion results demonstrated that MW-A pretreatment not only significantly increased cumulative biogas production, but also shortened the duration for a stable biogas production rate. Therefore, the alkaline microwaving pretreatment could become an alternative process for effective treatment of swine manure.

Novel bimetallic dispersed catalysts for temperature-programmed coal liquefaction. Technical progress report, October 1995--December 1995

Energy Technology Data Exchange (ETDEWEB)

Song, C.; Cooke, W.S.; Schmidt, E.; Schobert, H.H.

1996-02-01

Coal liquefaction involves cleavage of methylene, dimethylene and ether bridges connecting polycyclic aromatic units and the reactions of various oxygen functional groups. Here in this quarterly, we report on the catalytic effects of several molybdenum-, cobalt-, and iron-containing compounds in the reactions of dibenzothiophene (DBT) with hydrogen under conditions related to coal liquefaction. The catalytic effects of several molybdenum-, cobalt-, and iron-containing compounds have been examined in the hydrogenation and hydrodesulfurization reactions of dibenzothiophene (DBT) under conditions related to coal liquefaction. The metal compounds are candidate catalyst precursors for direct coal liquefaction. The reactions were carried out in batch microautoclave reactors at 400{degrees}C for 30 minutes with 6.9 MPa (cold) hydrogen pressure, and tridecane solvent. A metal loading of 0.5 mol% resulted in low conversion and only hydrogenation. Addition of sulfur in 4:1 molar ratio led only to a minor increase in conversion and hydrodesulfurization. The use of a higher boiling solvent (octadecane vs. tridecane) was beneficial in providing increased conversion, hydrodesulfurization, and hydrogenation. An increase in metal compound loading to 36.2 mol% led to a dramatic increase in conversion, hydrodesulfurization, and hydrocracking. Molybdenum hexacarbonyl at 36 mol% loading, with added sulfur at 6:1 ratio and octadecane solvent, gave 100% conversion of dibenzothiophene to other products with 100% hydrodesulfurization. Ammonium tetrathiomolybdate and molybdenum(III) chloride are less active under similar conditions. A cobalt-molybdenum thiocubane complex gave unexpectedly low conversions. Iron and cobalt carbonyls also provided very low conversions, even with added sulfur.

Report on the achievements in research and development of a coal liquefaction technology in the Sunshine Project in fiscal 1981. Development of a solvolysis liquefaction plant (development of a 1 t/d experimental plant and research on solvolysis liquefaction process); Sekitan ekika gijutsu no kenkyu kaihatsu, solvolysis ekika plant no kaihatsu seika hokokusho. 1t/nichi jikken plant no kaihatsu (solvolysis ekika process no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

This paper describes the achievements in the Sunshine Project in fiscal 1981 in development of a solvolysis liquefaction plant. The solvolysis process is characterized by performing the first stage reaction (liquefaction) in a short time by using hydrogenated heavy solvent produced spontaneously in the process. This short-time liquefaction reaction was carried out continuously by using a 1-t/d experimental plant, and a prospect was obtained on smooth operation and realization of the device. A test using a testing device allowing the temperature to rise within several minutes was performed on the effectiveness of a hydrogenated coal based heavy solvent (fractions of a hydrogenated heavy anthracene as a model) as a study on the first stage reaction. Partially hydrogenated materials of polycyclic condensed aromatics in the heavy solvent is largely involved in the initial reaction. In the solid-liquid separation, solids and heavy fractions are selected and removed from the first stage reaction products, and the light fraction is supplied into the second stage reaction (hydrogenation). The solvent deliming process was tested by using a batch type solid-liquid separator, whose effectiveness was verified. Studies were performed by using Australian sub-bituminous coal on operation of a continuous operation device consisted of systems for the first stage reaction (liquefaction), solid-liquid separation, second stage reaction (hydrogenation), and solvent circulation. (NEDO)

Combination of ensiling and fungal delignification as effective wheat straw pretreatment

DEFF Research Database (Denmark)

Thomsen, Sune T.; Londono, Jorge E. G.; Ambye-Jensen, Morten

2016-01-01

straw (WS). This study was undertaken to assess whether a combination of forced ensiling with Lactobacillus buchneri and WRF treatment using a low cellulase fungus, Ceriporiopsis subvermispora, could produce a relevant pretreatment effect on WS for bioethanol and biogas production. Results......: A combination of the ensiling and WRF treatment induced efficient pretreatment of WS by reducing lignin content and increasing enzymatic sugar release, thereby enabling an ethanol yield of 66 % of the theoretical max on the WS glucan, i.e. a yield comparable to yields obtained with high-tech, large......-scale pretreatment methods. The pretreatment effect was reached with only a minor total solids loss of 5 % by weight mainly caused by the fungal metabolism. The combination of the biopretreatments did not improve the methane potential of the WS, but improved the initial biogas production rate significantly...

Report for fiscal 1994 by subcommittee on coal liquefaction basic technology; 1994 nendo ekika kiban gijutsu bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-03-01

This report covers the proceedings of subcommittee meetings. Using PDUs (process development unit), comparison is made between bituminous coal-derived oils (150t/d plant for the Indonesian coal) and brown coal-derived oils (50t/d plant for the Yallourn coal), product quality is improved by a 2-stage refining process, engines are tested, etc., all these demonstration and research efforts intended to win social recognition for coal liquefaction products. Among basic studies, there are the development of technologies for reforming coal-derived oils and for mixing them will petroleum, development of new catalysts for reforming, development of a technology for separating heterocompounds and the like, and the development of their applications. Furthermore, technologies are developed for environmentally friendly coal liquefaction, feasibility of coal liquefaction technology internationalization is deliberated, and technical researches and joint researches are conducted. At the second meeting of the subcommittee, achievements relative to the refining and applications of liquefaction products are presented, including the hydrorefining of naphtha, heating oil, and light oil; development of new catalysts; heterocompound separation technology; and the development of new applications. In relation with the development of environmentally friendly coal liquefaction technologies, studies are presented on liquefaction conditions and on the upgrading of basic technologies of liquefaction. Also referred to are the reports delivered at a meeting on liquefaction catalysts (January 1995). (NEDO)

Production and Optimization of Direct Coal Liquefaction derived Low Carbon-Footprint Transportation Fuels

Energy Technology Data Exchange (ETDEWEB)

Steven Markovich

2010-06-30

This report summarizes works conducted under DOE Contract No. DE-FC26-05NT42448. The work scope was divided into two categories - (a) experimental program to pretreat and refine a coal derived syncrude sample to meet transportation fuels requirements; (b) system analysis of a commercial scale direct coal liquefaction facility. The coal syncrude was derived from a bituminous coal by Headwaters CTL, while the refining study was carried out under a subcontract to Axens North America. The system analysis included H{sub 2} production cost via six different options, conceptual process design, utilities requirements, CO{sub 2} emission and overall plant economy. As part of the system analysis, impact of various H{sub 2} production options was evaluated. For consistence the comparison was carried out using the DOE H2A model. However, assumptions in the model were updated using Headwaters database. Results of Tier 2 jet fuel specifications evaluation by the Fuels & Energy Branch, US Air Force Research Laboratory (AFRL/RZPF) located at Wright Patterson Air Force Base (Ohio) are also discussed in this report.

Pretreatment with polyamines alleviate the deleterious effects of diuron in maize leaves.

Science.gov (United States)

Durmuş, Nuran; Bekircan, Tuba

2015-03-01

The effects of diuron, a photosystem II inhibiting herbicide, on lipid peroxidation, photosynthetic pigments, soluble protein, proline contents and some antioxidant enzymes in maize leaves were studied and protective effects of polyamines against diuron toxicity were investigated. Diuron significantly increased lipid peroxidation, suggesting oxidative damage in the plants and proline content, while it decreased total chlorophyll, carotenoid and soluble protein levels in the leaves during the experiments. Pretreatment with polyamines statistically decreased lipid peroxidation induced by diuron and spermine (SPM) proved to be the most effective polyamine. Also, pretreatment with polyamines significantly prevented the losses of total chlorophyll, carotenoid and soluble protein induced by diuron. On the other hand, pretreatment with polyamines significantly increased proline contents of the leaves in comparison with the leaves treated with diuron. Superoxide dismutase (SOD), guaiacol peroxidase (GPX) and glutathione reductase (GR) activities increased in the leaves treated with diuron while catalase (CAT ) activity decreased. Pretreatment with spermidine (SPD) did not change significantly SOD activity at 24 and 72 hrs of diuron treatment but prevented the increase in SOD activity induced by diuron at 48 h. However, pretreatment with SPD increased GPX activity at 24 h and GR activity at 48 and 72 hrs. CAT activity in the leaves pretreated with SPD was similar to that of the leaves treated with diuron. Pretreatment with SPM prevented the increase in SOD activity induced by diuron at 48 h but significantly increased it at 72 h of diuron treatment. However, pretreatment with SPM did not significantly change GPX and GR activities during the experiments but reversed the decrease in CAT activity induced by diuron at 72 h. Pretreatment with putrescine (PUT) prevented the increase in SOD activity induced by diuron at 48 and 72 hrs while it increased GPX and GR activities at 48

Effect of alkaline microwaving pretreatment on anaerobic digestion and biogas production of swine manure

OpenAIRE

Tao Yu; Yihuan Deng; Hongyu Liu; Chunping Yang; Bingwen Wu; Guangming Zeng; Li Lu; Fumitake Nishimura

2017-01-01

Microwave assisted with alkaline (MW-A) condition was applied in the pretreatment of swine manure, and the effect of the pretreatment on anaerobic treatment and biogas production was evaluated in this study. The two main microwaving (MW) parameters, microwaving power and reaction time, were optimized for the pretreatment. Response surface methodology (RSM) was used to investigate the effect of alkaline microwaving process for manure pretreatment at various values of pH and energy input. Resul...

Development of an extruder-feeder biomass direct liquefaction process

Energy Technology Data Exchange (ETDEWEB)

White, D.H.; Wolf, D. (Arizona Univ., Tucson, AZ (United States). Dept. of Chemical Engineering)

1991-10-01

As an abundant, renewable, domestic energy resource, biomass could help the United States reduce its dependence on imported oil. Biomass is the only renewable energy technology capable of addressing the national need for liquid transportation fuels. Thus, there is an incentive to develop economic conversion processes for converting biomass, including wood, into liquid fuels. Through research sponsored by the US DOE's Biomass Thermochemical Conversion Program, the University of Arizona has developed a unique biomass direct liquefaction system. The system features a modified single-screw extruder capable of pumping solid slurries containing as high as 60 wt% wood flour in wood oil derived vacuum bottoms at pressures up to 3000 psi. The extruder-feeder has been integrated with a unique reactor by the University to form a system which offers potential for improving high pressure biomass direct liquefaction technology. The extruder-feeder acts simultaneously as both a feed preheater and a pumping device for injecting wood slurries into a high pressure reactor in the biomass liquefaction process. An experimental facility was constructed and following shakedown operations, wood crude oil was produced by mid-1985. By July 1988, a total of 57 experimental continuous biomass liquefaction runs were made using White Birch wood feedstock. Good operability was achieved at slurry feed rates up to 30 lb/hr, reactor pressures from 800 to 3000 psi and temperatures from 350{degree}C to 430{degree}C under conditions covering a range of carbon monoxide feed rates and sodium carbonate catalyst addition. Crude wood oils containing as little as 6--10 wt% residual oxygen were produced. 38 refs., 82 figs., 26 tabs.

Studies on liquefaction and pyrolysis of peat and biomass at KTH

International Nuclear Information System (INIS)

Bjoernbom, E.; Sjoestrom, K.; Hoernel, C.; Zanzi, R.; Bjoernbom, P.

1996-01-01

A brief review of the study on thermochemical conversion of solid fuels is done. The study have been performed in the Royal Institute of Technology, Stockholm, since the outbreak of energy crisis in the seventies. The main problems connected with utilisation of peat for energy are: 90% moisture content in the deposits and 35-40% oxygen content in the dry substance. Simultaneous dewatering and liquefaction of peat have been achieved by the Bjoerbom method. The wet peat has been treated with CO and H 2 O without preliminary drying, using water as a medium agent. After treatment water has been phase-separated from the heavy oil product. Another approach is de-oxygenation of peat prior to liquefaction. A significant part of oxygen in peat and biomass can be removed by thermal decomposition of the fuels prior to liquefaction and removal of carbon dioxide and water from the organic matter in them. The products obtained after de-oxygenation demand low consumption of external hydrogenation agent because they are rich in hydrogen. Some criteria for selection of peat as a raw material for liquefaction are given. The equipment and experimental procedure for pyrolysis of peat and biomass are described. A free fall tubular reactor with max operating pressure of 5 MPa and temperature of 1100 o C has been used. The effect of treatment conditions under the rapid pyrolysis in the free fall reactor on the yield and the reactivity of char obtained after the final pyrolysis is shown. Peat and wood are transformed into pyrolysis products for less than 1 second; 35-50% of the moisture- and ash-free peat and 70% of the wood have been converted into gaseous products.The char obtained in the rapid pyrolysis contains a fraction which can be further de-volatilized by slow pyrolysis for a few minutes - time much longer than the time for formation of primary products. High reactivity of char is favoured by lower pyrolysis temperature, shorter residence time and larger particle size of the fuel

Histotripsy Liquefaction of Large Hematomas.

Science.gov (United States)

Khokhlova, Tatiana D; Monsky, Wayne L; Haider, Yasser A; Maxwell, Adam D; Wang, Yak-Nam; Matula, Thomas J

2016-07-01

Intra- and extra-muscular hematomas result from repetitive injury as well as sharp and blunt limb trauma. The clinical consequences can be serious, including debilitating pain and functional deficit. There are currently no short-term treatment options for large hematomas, only lengthy conservative treatment. The goal of this work was to evaluate the feasibility of a high intensity focused ultrasound (HIFU)-based technique, termed histotripsy, for rapid (within a clinically relevant timeframe of 15-20 min) liquefaction of large volume (up to 20 mL) extra-vascular hematomas for subsequent fine-needle aspiration. Experiments were performed using in vitro extravascular hematoma phantoms-fresh bovine blood poured into 50 mL molds and allowed to clot. The resulting phantoms were treated by boiling histotripsy (BH), cavitation histotripsy (CH) or a combination in a degassed water tank under ultrasound guidance. Two different transducers operating at 1 MHz and 1.5 MHz with f-number = 1 were used. The liquefied lysate was aspirated and analyzed by histology and sized in a Coulter Counter. The peak instantaneous power to achieve BH was lower than (at 1.5 MHz) or equal to (at 1 MHz) that which was required to initiate CH. Under the same exposure duration, BH-induced cavities were one and a half to two times larger than the CH-induced cavities, but the CH-induced cavities were more regularly shaped, facilitating easier aspiration. The lysates contained a small amount of debris larger than 70 μm, and 99% of particulates were smaller than 10 μm. A combination treatment of BH (for initial debulking) and CH (for liquefaction of small residual fragments) yielded 20 mL of lysate within 17.5 minutes of treatment and was found to be most optimal for liquefaction of large extravascular hematomas. Copyright © 2016 World Federation for Ultrasound in Medicine & Biology. Published by Elsevier Inc. All rights reserved.

Liquefaction of H2 molecules upon exterior surfaces of carbon nanotube bundles

International Nuclear Information System (INIS)

Han, Sang Soo; Kang, Jeung Ku; Lee, Hyuck Mo; Duin, Adri C.T. van; Goddard, William A. III

2005-01-01

We have used molecular dynamics simulations to investigate interaction of H 2 molecules on the exterior surfaces of carbon nanotubes (CNTs): single and bundle types. At 80 K and 10 MPa, it is found that charge transfer occurs from a low curvature region to a high curvature region of the deformed CNT bundle, which develops charge polarization only on the deformed structure. The long-range electrostatic interactions of polarized charges on the deformed CNT bundle with hydrogen molecules are observed to induce a high local-ordering of H 2 gas that results in hydrogen liquefaction. Our predicted heat of hydrogen liquefaction on the CNT bundle is 97.6 kcal kg -1 . On the other hand, hydrogen liquefaction is not observed in the CNT of a single type. This is because charge polarization is not developed on the single CNT as it is symmetrically deformed under the same pressure. Consequently, the hydrogen storage capacity on the CNT bundle is much higher due to liquefaction than that on the single CNT. Additionally, our results indicate that it would also be possible to liquefy H 2 gas on a more strongly polarized CNT bundle at temperatures higher than 80 K

Dynamic dielectric properties of a wood liquefaction system using polyethylene glycol and glycerol

Science.gov (United States)

Mengchao Zhou; Thomas L. Eberhardt; Bo Cai; Chung-Yun Hse; Hui Pan

2017-01-01

Microwave-assisted liquefaction has shown potential for rapid thermal processing of lignocellulosic biomass. The efficiency of microwave heating depends largely on the dielectric properties of the materials being heated. The objective of this study was to investigate the dynamic interactions between microwave energy and the reaction system during the liquefaction of a...

Design, synthesis, and characterization of novel fine-particle, unsupported catalysts for coal liquefaction

Energy Technology Data Exchange (ETDEWEB)

Klein, M.T.

1991-12-30

The purpose of this work is to investigate the kinetics-assisted design, synthesis and characterization of fme-pardcle, unsupported catalysts for coal liquefaction. The goal is to develop a fundamental understanding of coal catalysis and catalysts that will, in turn, allow for the specification of a novel optimal catalyst for coal liquefaction.

Catalytic activity of pyrite for coal liquefaction reaction; Tennen pyrite no shokubai seino ni kansuru kento

Energy Technology Data Exchange (ETDEWEB)

Hirano, K.; Kozu, M.; Okada, T.; Kobayashi, M. [Nippon Coal Oil Co. Ltd., Tokyo (Japan)

1996-10-28

Since natural pyrite is easy to obtain and cheap as coal liquefaction catalyst, it is to be used for the 150 t/d scale NEDOL process bituminous coal liquefaction pilot plant. NEDO and NCOL have investigated the improvement of catalytic activity of pulverized natural pyrite for enhancing performance and economy of the NEDOL process. In this study, coal liquefaction tests were conducted using natural pyrite catalyst pulverized by dry-type bowl mill under nitrogen atmosphere. Mechanism of catalytic reaction of the natural pyrite was discussed from relations between properties of the catalyst and liquefaction product. The natural pyrite provided an activity to transfer gaseous hydrogen into the liquefaction product. It was considered that pulverized pyrite promotes the hydrogenation reaction of asphaltene because pulverization increases its contact rate with reactant and the amount of active points on its surface. It was inferred that catalytic activity of pyrite is affected greatly by the chemical state of Fe and S on its surface. 3 refs., 4 figs., 1 tab.

Direct liquefaction of low-rank coals under mild conditions

Energy Technology Data Exchange (ETDEWEB)

Braun, N.; Rinaldi, R. [Max-Planck-Institut fuer Kohlenforschung, Muelheim an der Ruhr (Germany)

2013-11-01

Due to decreasing of petroleum reserves, direct coal liquefaction is attracting renewed interest as an alternative process to produce liquid fuels. The combination of hydrogen peroxide and coal is not a new one. In the early 1980, Vasilakos and Clinton described a procedure for desulfurization by leaching coal with solutions of sulphuric acid/H{sub 2}O{sub 2}. But so far, H{sub 2}O{sub 2} has never been ascribed a major role in coal liquefaction. Herein, we describe a novel approach for liquefying low-rank coals using a solution of H{sub 2}O{sub 2} in presence of a soluble non-transition metal catalyst. (orig.)

Effect of Different Sugar Beet Pulp Pretreatments on Biogas Production Efficiency.

Science.gov (United States)

Ziemiński, Krzysztof; Kowalska-Wentel, Monika

2017-03-01

The objective of this study was to determine the effect of different sugar beet pulp (SBP) pretreatments on biogas yield from anaerobic digestion. SBP was subjected to grinding, thermal-pressure processing, enzymatic hydrolysis, or combination of these pretreatments. It was observed that grinding of SBP to 2.5-mm particles resulted in the cumulative biogas productivity of 617.2 mL/g volatile solids (VS), which was 20.2 % higher compared to the biogas yield from the not pretreated SBP, and comparable to that from not ground, enzymatically hydrolyzed SBP. The highest cumulative biogas productivity, 898.7 mL/g VS, was obtained from the ground, thermal-pressure pretreated and enzymatically hydrolyzed SBP. The latter pretreatment variant enabled to achieve the highest glucose concentration (24.765 mg/mL) in the enzymatic hydrolysates. The analysis of energy balance showed that the increase in the number of SBP pretreatment operations significantly reduced the gain of electric energy.

Probabilistic versus deterministic hazard assessment in liquefaction susceptible zones

Science.gov (United States)

Daminelli, Rosastella; Gerosa, Daniele; Marcellini, Alberto; Tento, Alberto

2015-04-01

Probabilistic seismic hazard assessment (PSHA), usually adopted in the framework of seismic codes redaction, is based on Poissonian description of the temporal occurrence, negative exponential distribution of magnitude and attenuation relationship with log-normal distribution of PGA or response spectrum. The main positive aspect of this approach stems into the fact that is presently a standard for the majority of countries, but there are weak points in particular regarding the physical description of the earthquake phenomenon. Factors like site effects, source characteristics like duration of the strong motion and directivity that could significantly influence the expected motion at the site are not taken into account by PSHA. Deterministic models can better evaluate the ground motion at a site from a physical point of view, but its prediction reliability depends on the degree of knowledge of the source, wave propagation and soil parameters. We compare these two approaches in selected sites affected by the May 2012 Emilia-Romagna and Lombardia earthquake, that caused widespread liquefaction phenomena unusually for magnitude less than 6. We focus on sites liquefiable because of their soil mechanical parameters and water table level. Our analysis shows that the choice between deterministic and probabilistic hazard analysis is strongly dependent on site conditions. The looser the soil and the higher the liquefaction potential, the more suitable is the deterministic approach. Source characteristics, in particular the duration of strong ground motion, have long since recognized as relevant to induce liquefaction; unfortunately a quantitative prediction of these parameters appears very unlikely, dramatically reducing the possibility of their adoption in hazard assessment. Last but not least, the economic factors are relevant in the choice of the approach. The case history of 2012 Emilia-Romagna and Lombardia earthquake, with an officially estimated cost of 6 billions

Influence of the void ratio and the confining on the static liquefaction in slopes in shangi sand

Directory of Open Access Journals (Sweden)

Alfonso Mariano Ramos Cañón

2015-01-01

Full Text Available A numerical study on the onset of static liquefaction in slopes under undrained conditions of loading was developed based on a general liquefaction flow instability criterion for elastoplastic soils based on the concept of loss of controllability. The criterion is applied to the case of axisymmetric loading to detect the onset of static liquefaction. The criterion is used in conjunction with an elastoplastic model for sands and is tested by means of numerical simulations of element tests. The numerical results are compared with experimental evidence obtaining good agreement. A quantitative study of the influence of the mean pressure, void ratio and the anisotropy of stress on the onset of static liquefaction is presented for the Changi sand. From the analysis of the numerical results, it can be concluded that: a. the mobilized friction angle at the onset of liquefaction is not an intrinsic property of the material, but is a state variable b. Despite of the multiple variables involved in the process of generation of undrained instability, the state of stresses at the onset of static liquefaction can be conveniently represented by a linear relation between Dq/po and no . This graphical representation can be used in the practice of geotechnical engineering to quantify the margin of security against the static liquefaction of a sandy slope.

Effect of ultrasonic pretreatment on purified water disinfection

International Nuclear Information System (INIS)

Simon Andreu, P.; Lardin Mifsut, C.; Vergara Romero, L.; Polo Canas, P. M.; Perez Sanchez, P.; Rancano Perez, A.

2009-01-01

Due to the importance of a suitable water disinfection in order to insure a pollutant effect minimization against environment, this work has been carried out to determine how can affect an ultrasonic pre-treatment upon disinfection step. It has been confirmed the ultrasonic disintegration of bacterial cells in treated water and disinfectant power of treatment by itself, which is not enough to be used as a single method in water disinfection. It has also been proved that from a technical and economical point of view the combination of UV and ultrasound improves the UV treatment performance. Finally, it has been detected that an ultrasonic pre-treatment increases chlorination effectiveness, however the high cost in this combination makes it unfeasible of industrial scale. (Author) 6 refs

Solvent recyclability in a multistep direct liquefaction process

Energy Technology Data Exchange (ETDEWEB)

Hetland, M.D.; Rindt, J.R. [Univ. of North Dakota, Grand Forks, ND (United States)

1995-12-31

Direct liquefaction research at the Energy & Environmental Research Center (EERC) has, for a number of years, concentrated on developing a direct liquefaction process specifically for low-rank coals (LRCs) through the use of hydrogen-donating solvents and solvents similar to coal-derived liquids, the water/gas shift reaction, and lower-severity reaction conditions. The underlying assumption of all of the research was that advantage could be taken of the reactivity and specific qualities of LRCs to produce a tetrahydrofuran (THF)-soluble material that might be easier to upgrade than the soluble residuum produced during direct liquefaction of high-rank coals. A multistep approach was taken to produce the THF-soluble material, consisting of (1) preconversion treatment to prepare the coal for solubilization, (2) solubilization of the coal in the solvent, and (3) polishing to complete solubilization of the remaining material. The product of these three steps can then be upgraded during a traditional hydrotreatment step. The results of the EERC`s research indicated that additional studies to develop this process more fully were justified. Two areas were targeted for further research: (1) determination of the recyclability of the solvent used during solubilization and (2) determination of the minimum severity required for hydrotreatment of the liquid product. The current project was funded to investigate these two areas.

Vitamin C Pretreatment Enhances the Antibacterial Effect of Cold Atmospheric Plasma

DEFF Research Database (Denmark)

Helgadottir, Saga; Pandit, Santosh; Mokkapati, Venkata R. S. S.

2017-01-01

intervals and to evaluate the effect of combined treatment with vitamin C. We demonstrate that CAP is not very effective against 48 h mature bacterial biofilms of several common opportunistic pathogens: Staphylococcus epidermidis, Escherichia coli, and Pseudomonas aeruginosa. However, if bacterial biofilms...... are pre-treated with vitamin C for 15 min before exposure to CAP, a significantly stronger bactericidal effect can be obtained. Vitamin C pretreatment enhances the bactericidal effect of cold plasma by reducing the viability from 10 to 2% in E. coli biofilm, 50 to 11% in P. aeruginosa, and 61 to 18% in S....... epidermidis biofilm. Since it is not feasible to use extended CAP treatments in medical practice, we argue that the pre-treatment of infectious lesions with vitamin C prior to CAP exposure can be a viable route for efficient eradication of bacterial biofilms in many different applications....

Economically viable large-scale hydrogen liquefaction

Science.gov (United States)

Cardella, U.; Decker, L.; Klein, H.

2017-02-01

The liquid hydrogen demand, particularly driven by clean energy applications, will rise in the near future. As industrial large scale liquefiers will play a major role within the hydrogen supply chain, production capacity will have to increase by a multiple of today’s typical sizes. The main goal is to reduce the total cost of ownership for these plants by increasing energy efficiency with innovative and simple process designs, optimized in capital expenditure. New concepts must ensure a manageable plant complexity and flexible operability. In the phase of process development and selection, a dimensioning of key equipment for large scale liquefiers, such as turbines and compressors as well as heat exchangers, must be performed iteratively to ensure technological feasibility and maturity. Further critical aspects related to hydrogen liquefaction, e.g. fluid properties, ortho-para hydrogen conversion, and coldbox configuration, must be analysed in detail. This paper provides an overview on the approach, challenges and preliminary results in the development of efficient as well as economically viable concepts for large-scale hydrogen liquefaction.

FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of materials for the coal liquefaction plant); 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sekitan ekika plant zairyo no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

A 1 T/D solvent-extraction type coal liquefaction test plant was constructed and operated to obtain the technical data for the design of, and establish the techniques for, an efficient coal liquefaction plant. The FY 1980 program includes surveys on the materials for coal liquefaction plants, covering those already developed and under development, to clarify the problematical points; drafting the test schedules; and conceptual designs of the material testing facilities. The major problems involved in the materials for coal liquefaction plants include erosion by fluidizing coal slurry, hydrogen embrittlement of the reactor materials, and corrosion by the liquefaction products (e.g., stress-corrosion cracking of austenitic steel, and corrosion by organic acids). The surveys on materials research trends suggest that USA seems to concentrate their research efforts on the reactor materials. The corrosion tests are mostly of in-plant tests, but the stress corrosion and slurry erosion tests are conducted on a laboratory scale. The conceptual designs are drawn for some testing units, e.g., the loop type material testing unit and basic testing unit for jet-spray type slurry erosion. (NEDO)

Renewable chemical feedstocks from integrated liquefaction processing of lingocellulosic materials using microwave energy

Science.gov (United States)

Junming Xu; Jianchun Jiang; Chung-Yun Hse; Todd F. Shupe

2012-01-01

The objective of this investigation was to find a simple method for the production of phenolic rich products and sugar derivatives (biopolyols) via separation of liquefied lingocellulosic materials. Liquefaction of lignocellulosic materials was conducted in methanol at 180 °C for 15 min with the conversion of raw materials at about 75%. After liquefaction, the...

The direct liquefaction proof of concept program

Energy Technology Data Exchange (ETDEWEB)

Comolli, A.G.; Lee, L.K.; Pradhan, V.R.; Stalzer, R.H. [New York & Puritan Avenues, Lawrenceville, NJ (United States)

1995-12-31

The goal of the Proof of Concept (POC) Program is to develop Direct Coal Liquefaction and associated transitional technologies towards commercial readiness for economically producing premium liquid fuels from coal in an environmentally acceptable manner. The program focuses on developing the two-stage liquefaction (TSL) process by utilizing geographically strategic feedstocks, commercially feasible catalysts, new prototype equipment, and testing co-processing or alternate feedstocks and improved process configurations. Other high priority objectives include dispersed catalyst studies, demonstrating low rank coal liquefaction without solids deposition, improving distillate yields on a unit reactor volume basis, demonstrating ebullated bed operations while obtaining scale-up data, demonstrating optimum catalyst consumption using new concepts (e.g. regeneration, cascading), producing premium products through on-line hydrotreating, demonstrating improved hydrogen utilization for low rank coals using novel heteroatom removal methods, defining and demonstrating two-stage product properties for upgrading; demonstrating efficient and economic solid separation methods, examining the merits of integrated coal cleaning, demonstrating co-processing, studying interactions between the preheater and first and second-stage reactors, improving process operability by testing and incorporating advanced equipment and instrumentation, and demonstrating operation with alternate coal feedstocks. During the past two years major PDU Proof of Concept runs were completed. POC-1 with Illinois No. 6 coal and POC-2 with Black Thunder sub-bituminous coal. Results from these operations are continuing under review and the products are being further refined and upgraded. This paper will update the results from these operations and discuss future plans for the POC program.

[Protective effect of Uncaria rhynchophylla total alkaloids pretreatment on hippocampal neurons after acute hypoxia].

Science.gov (United States)

Liu, Wei; Zhang, Zhao-qin; Zhao, Xiao-min; Gao, Yun-sheng

2006-05-01

To investigate the effect of Uncaria rhynchophylla total alkaloids (RTA) pretreatment on the voltage-gated sodium currents of the rat hippocampal neurons after acute hypoxia. Primary cultured hippocampal neurons were divided into RTA pre-treated and non-pretreated groups. Patch clamp whole-cell recording was used to compare the voltage-gated sodium current amplitude and threshold with those before hypoxia. After acute hypoxia, sodium current amplitude was significantly decreased and its threshold was upside. RTA pretreatment could inhibit the reduction of sodium current amplitude. RTA pretreatment alleviates the acute hypoxia-induced change of sodium currents, which may be one of the mechanisms for protective effect of RTA on cells.

Mechanism of waste biomass pyrolysis: Effect of physical and chemical pre-treatments

International Nuclear Information System (INIS)

Das, Oisik; Sarmah, Ajit K.

2015-01-01

To impart usability in waste based biomass through thermo-chemical reactions, several physical and chemical pre-treatments were conducted to gain an insight on their mode of action, effect on the chemistry and the change in thermal degradation profiles. Two different waste biomasses (Douglas fir, a softwood and hybrid poplar, a hardwood) were subjected to four different pre-treatments, namely, hot water pre-treatment, torrefaction, acid (sulphuric acid) and salt (ammonium phosphate) doping. Post pre-treatments, the changes in the biomass structure, chemistry, and thermal makeup were studied through electron microscopy, atomic absorption/ultra violet spectroscopy, ion exchange chromatography, and thermogravimetry. The pre-treatments significantly reduced the amounts of inorganic ash, extractives, metals, and hemicellulose from both the biomass samples. Furthermore, hot water and torrefaction pre-treatment caused mechanical disruption in biomass fibres leading to smaller particle sizes. Torrefaction of Douglas fir wood yielded more solid product than hybrid poplar. Finally, the salt pre-treatment increased the activation energies of the biomass samples (especially Douglas fir) to a great extent. Thus, salt pre-treatment was found to bestow thermal stability in the biomass. - Highlights: • Pre-treatments reduce ash, extractives, alkalines and hemicellulose from biomass. • Torrefaction of Douglas fir yields more solid product than hybrid poplar. • Salt pretreatment significantly increases the activation energy of biomass. • Acid and salt pretreatment bestows thermal stability in biomass.

Mechanism of waste biomass pyrolysis: Effect of physical and chemical pre-treatments

Energy Technology Data Exchange (ETDEWEB)

Das, Oisik [Department of Biological Systems Engineering, Washington State University, Pullman 99164-6120, WA (United States); Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand); Sarmah, Ajit K., E-mail: a.sarmah@auckland.ac.nz [Department of Civil and Environmental Engineering, University of Auckland, Auckland 1142 (New Zealand)

2015-12-15

To impart usability in waste based biomass through thermo-chemical reactions, several physical and chemical pre-treatments were conducted to gain an insight on their mode of action, effect on the chemistry and the change in thermal degradation profiles. Two different waste biomasses (Douglas fir, a softwood and hybrid poplar, a hardwood) were subjected to four different pre-treatments, namely, hot water pre-treatment, torrefaction, acid (sulphuric acid) and salt (ammonium phosphate) doping. Post pre-treatments, the changes in the biomass structure, chemistry, and thermal makeup were studied through electron microscopy, atomic absorption/ultra violet spectroscopy, ion exchange chromatography, and thermogravimetry. The pre-treatments significantly reduced the amounts of inorganic ash, extractives, metals, and hemicellulose from both the biomass samples. Furthermore, hot water and torrefaction pre-treatment caused mechanical disruption in biomass fibres leading to smaller particle sizes. Torrefaction of Douglas fir wood yielded more solid product than hybrid poplar. Finally, the salt pre-treatment increased the activation energies of the biomass samples (especially Douglas fir) to a great extent. Thus, salt pre-treatment was found to bestow thermal stability in the biomass. - Highlights: • Pre-treatments reduce ash, extractives, alkalines and hemicellulose from biomass. • Torrefaction of Douglas fir yields more solid product than hybrid poplar. • Salt pretreatment significantly increases the activation energy of biomass. • Acid and salt pretreatment bestows thermal stability in biomass.

Effect of Glycerol Pretreatment on Levoglucosan Production from Corncobs by Fast Pyrolysis

Directory of Open Access Journals (Sweden)

Liqun Jiang

2017-11-01

Full Text Available In this manuscript, glycerol was used in corncobs’ pretreatment to promote levoglucosan production by fast pyrolysis first and then was further utilized as raw material for chemicals production by microbial fermentation. The effects of glycerol pretreatment temperatures (220–240 °C, time (0.5–3 h and solid-to-liquid ratios (5–20% were investigated. Due to the accumulation of crystalline cellulose and the removal of minerals, the levoglucosan yield was as high as 35.8% from corncobs pretreated by glycerol at 240 for 3 h with a 5% solid-to-liquid ratio, which was obviously higher than that of the control (2.2%. After glycerol pretreatment, the fermentability of the recovered glycerol remaining in the liquid stream from glycerol pretreatment was evaluated by Klebsiella pneumoniae. The results showed that the recovered glycerol had no inhibitory effect on the growth and metabolism of the microbe, which was a promising substrate for fermentation. The value-added applications of glycerol could reduce the cost of biomass pretreatment. Correspondingly, this manuscript offers a green, sustainable, efficient and economic strategy for an integrated biorefinery process.

Survey on the trend of coal liquefaction/gasification technologies, broken down by application; Sekitan no ekika gas ka no yotobetsu gijutsu no doko chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1983-03-01

To drive forward the development of the above-named technologies efficiently and effectively, it is necessary to clearly define what coal derived products will meet the need of the clientele and to develop coal derived products accordingly. This survey aims to disclose the whole pictures of the oil/gas using areas and enable the study and evaluation of the possibilities of using coal derived products as substitutes in every one of the expected applications. It also aims to clarify product characteristics, use conditions, technical tasks, and problems to accompany actual substitution in the applications where possibilities are high of their serving as substitutes. Chapter 1, explaining the trend of coal liquefaction/gasification technologies, describes projects for the development of coal liquefaction/gasification technologies, trend of the development of coal liquefaction/gasification technologies, and properties of coal liquefaction/gasification products. Chapter 2, explaining the trend of demand for energy for use in the respective applications, analyzes the trend of demands for oil products, gases, and methanol. Chapter 3 summarizes the applications of chemical materials and fuels for studying the use of coal liquefaction/gasification products as substitutes in the respective applications. Chapter 4 collects problems to solve for the enhancement of coal liquefaction/gasification projects. (NEDO)

Hydrothermal Liquefaction of the Microalgae Phaeodactylum tricornutum

DEFF Research Database (Denmark)

Sigaard Christensen, Per; Peng, Gaël; Vogel, Frédéric

2014-01-01

The microalgae Phaeodactylum tricornutum was processed by hydrothermal liquefaction in order to assess the influence of reaction temperature and reaction time on the product and elemental distribution. The experiments were carried out at different reaction times (5 and 15 min) and over a wide range...

The making of Andersen’s liquefaction chart

DEFF Research Database (Denmark)

Sabaliauskas, Tomas; Ibsen, Lars Bo

Andersen’s chart (Andersen & Berre, 1999) is a graphical method of observing cyclic soil response. It allows observing soil response to various stress amplitudes that can lead to liquefaction, excess plastic deformation stabilizing soil response.The process of obtaining the original chart has been...

A study on the hydrotreating of coal hydro liquefaction residue and its kinetics

Energy Technology Data Exchange (ETDEWEB)

Huang, J.; Lu, X.; Zhang, D.; Gao, J. [Department of Chemical Engineering for Energy Resources, East China University of Science and Technology, Shanghai (China)

2010-09-15

Hydro-conversion of coal hydro liquefaction residue obtained from a 6 t/day pilot plant of Shenhua Group in Shanghai was carried out under the hydrotreating condition. The coal hydro liquefaction residue and its product were extracted in sequence with n-hexane, toluene and tetrahydrofuran in a Soxhlet apparatus. The n-hexane soluble fractions increased with the increase of reaction temperature and time. Its amount increased from 14.14% to a maximum of 40.86% under the conditions of 470 {sup o}C and 30 min, which meant that moderate extension of coal residence time in the coal hydro liquefaction reactor is beneficial to the increase of oil yield. A 4-lumped kinetic model of coal hydro liquefaction residue hydro-conversion was performed using solubility-based lumped fractions. In the model, the tetrahydrofuran insoluble fractions were classified into two parts: easily reactive part and unreactive part. The kinetic parameters were estimated by a fourth-order Runge-Kutta method and a nonlinear least squares method, and the apparent activation energies were calculated according to the Arrhenius Equation. A large quantity of total catalyst consisting of remained liquefaction catalyst, part of the mineral from raw coal and additive Fe-based catalyst could considerably reduce the apparent activation energy of hydro-conversion for the toluene insoluble/tetrahydrofuran insoluble fractions to 36.79 kJ-mol{sup -1}. The calculated values of the model coincided well with the experimental values. (authors)

Numerical simulation of liquefaction behaviour of granular materials ...

Indian Academy of Sciences (India)

R. Narasimhan (Krishtel eMaging) 1461 1996 Oct 15 13:05:22

cles using Discrete Element Method (DEM) is used to study the liquefaction behaviour of ... studies have focussed on the stress-strain relation- ... experimentation still remains quite problematic. ... distorting the periodic cell and changing its vol-.

Whole Algae Hydrothermal Liquefaction: 2014 State of Technology

Energy Technology Data Exchange (ETDEWEB)

Jones, Susanne B.; Zhu, Yunhua; Snowden-Swan, Lesley J.; Anderson, Daniel; Hallen, Richard T.; Schmidt, Andrew J.; Albrecht, Karl O.; Elliott, Douglas C.

2014-07-30

This report describes the base case yields and operating conditions for converting whole microalgae via hydrothermal liquefaction and upgrading to liquid fuels. This serves as the basis against which future technical improvements will be measured.

Fiscal 1991 report on the brown coal liquefaction section meeting; 1991 nendo kattan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

At the 1st through 5th brown coal liquefaction group meetings held for the fiscal year, reports are delivered and discussions are made about the progress of research and development. At the 1st meeting, a fiscal 1991 brown coal liquefaction research plan is introduced, and discussed. At the 2nd meeting, an interim report on the brown coal liquefaction technology development project is discussed. At the 3rd meeting (a joint meeting of the brown coal and bituminous coal liquefaction groups), an agendum entitled 'what the development of brown/bituminous coal liquefaction technologies for the 21st century should be' is reported, and discussed. At the 4th meeting, reports are made on the results of deliberation at the Industrial Technology Council, progress of the follow-up study, progress of the collection of achievements, and so forth. At the 5th meeting, the outline of the follow-up study, the collection of achievements in the pilot plant study (a project report preparation schedule and materials evaluation), the progress of pilot plant dismantling work, etc., are reported and discussed. (NEDO)

Fiscal 1991 report on the brown coal liquefaction section meeting; 1991 nendo kattan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1992-03-01

At the 1st through 5th brown coal liquefaction group meetings held for the fiscal year, reports are delivered and discussions are made about the progress of research and development. At the 1st meeting, a fiscal 1991 brown coal liquefaction research plan is introduced, and discussed. At the 2nd meeting, an interim report on the brown coal liquefaction technology development project is discussed. At the 3rd meeting (a joint meeting of the brown coal and bituminous coal liquefaction groups), an agendum entitled 'what the development of brown/bituminous coal liquefaction technologies for the 21st century should be' is reported, and discussed. At the 4th meeting, reports are made on the results of deliberation at the Industrial Technology Council, progress of the follow-up study, progress of the collection of achievements, and so forth. At the 5th meeting, the outline of the follow-up study, the collection of achievements in the pilot plant study (a project report preparation schedule and materials evaluation), the progress of pilot plant dismantling work, etc., are reported and discussed. (NEDO)

Liquefaction analysis of alluvial soil deposits in Bedsa south west of Cairo

Directory of Open Access Journals (Sweden)

Kamal Mohamed Hafez Ismail Ibrahim

2014-09-01

Full Text Available Bedsa is one of the districts in Dahshour that lays south west of Cairo and suffered from liquefaction during October 1992 earthquake, Egypt. The soil profile consists of alluvial river Nile deposits mainly sandy mud with low plasticity; the ground water is shallow. The earthquake hypocenter was 18 km far away with local magnitude 5.8; the fault length was 13.8 km, as recorded by the Egyptian national seismological network (ENSN at Helwan. The analysis used the empirical method introduced by the national center for earthquake engineering research (NCEER based on field standard penetration of soil. It is found that the studied area can liquefy since there are saturated loose sandy silt layers at depth ranges from 7 to 14 m. The settlement is about 26 cm. The probability of liquefaction ranges between 40% and 100%. The presence of impermeable surface from medium cohesive silty clay acts as a plug resisting and trapping the upward flow of water during liquefaction, so fountain and spouts at weak points occurs. It is wise to use point bearing piles with foundation level deeper than 14 m beyond the liquefiable depth away from ground slopes, otherwise liquefaction improving techniques have to be applied in the area.

Fiscal 1993 report. Coal liquefaction committee; 1993 nendo sekitan ekika iinkai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The committee in this fiscal year had the 1st meeting in July 1993, the 2nd in December 1993, and the 3rd in March 1994, when fiscal 1993 research and development programs and results were reported and discussed. Reported and discussed at the 2nd meeting were the compilation of brown coal liquefaction technology development project results, evaluation report on the same, hydrorefining of oil from brown coal and the research and development of application technologies for the same, and an environmental safety evaluation test on the same. In selecting a standard coal for the operation of the 150 ton/day pilot plant, PSU (process supporting unit)-aided studies were made on the analytical values presented by coals, yield of the liquid, yield of the liquefaction residue, yield of the generated gas, amount of the hydrogen consumed, coal oil properties, liquefaction residue properties, operationality, etc. On-site investigations were conducted also in Indonesia, and a conclusion was reached that Tanito Harum coal would be the most suitable for the pilot plant. Concerning the liquefaction catalyst for the pilot plant, a report was given on a comparison made between the activity of a synthetic iron sulfide and that of natural pyrite. (NEDO)

Cooperative research program in coal liquefaction. Quarterly report, May 1, 1993--October 31, 1993

Energy Technology Data Exchange (ETDEWEB)

Hoffman, G.P. [ed.

1994-07-01

This report summarizes progress in four areas of research under the general heading of Coal Liquefaction. Results of studies concerning the coliquefaction of coal with waste organic polymers or chemical products of these polymers were reported. Secondly, studies of catalytic systems for the production of clean transportation fuels from coal were discussed. Thirdly, investigations of the chemical composition of coals and their dehydrogenated counterparts were presented. These studies were directed toward elucidation of coal liquefaction processes on the chemical level. Finally, analytical methodologies developed for in situ monitoring of coal liquefaction were reported. Techniques utilizing model reactions and methods based on XAFS, ESR, and GC/MS are discussed.

Liquefaction of Semen Generates and Later Degrades a Conserved Semenogelin Peptide That Enhances HIV Infection

Science.gov (United States)

Liu, Haichuan; Usmani, Shariq M.; Neidleman, Jason; Müller, Janis A.; Avila-Herrera, Aram; Gawanbacht, Ali; Zirafi, Onofrio; Chu, Simon; Dong, Ming; Kumar, Senthil T.; Smith, James F.; Pollard, Katherine S.; Fändrich, Marcus; Kirchhoff, Frank; Münch, Jan; Witkowska, H. Ewa; Greene, Warner C.

2014-01-01

ABSTRACT Semen enhances HIV infection in vitro, but how long it retains this activity has not been carefully examined. Immediately postejaculation, semen exists as a semisolid coagulum, which then converts to a more liquid form in a process termed liquefaction. We demonstrate that early during liquefaction, semen exhibits maximal HIV-enhancing activity that gradually declines upon further incubation. The decline in HIV-enhancing activity parallels the degradation of peptide fragments derived from the semenogelins (SEMs), the major components of the coagulum that are cleaved in a site-specific and progressive manner upon initiation of liquefaction. Because amyloid fibrils generated from SEM fragments were recently demonstrated to enhance HIV infection, we set out to determine whether any of the liquefaction-generated SEM fragments associate with the presence of HIV-enhancing activity. We identify SEM1 from amino acids 86 to 107 [SEM1(86-107)] to be a short, cationic, amyloidogenic SEM peptide that is generated early in the process of liquefaction but that, conversely, is lost during prolonged liquefaction due to the activity of serine proteases. Synthetic SEM1(86-107) amyloids directly bind HIV-1 virions and are sufficient to enhance HIV infection of permissive cells. Furthermore, endogenous seminal levels of SEM1(86-107) correlate with donor-dependent variations in viral enhancement activity, and antibodies generated against SEM1(86-107) recognize endogenous amyloids in human semen. The amyloidogenic potential of SEM1(86-107) and its virus-enhancing properties are conserved among great apes, suggesting an evolutionarily conserved function. These studies identify SEM1(86-107) to be a key, HIV-enhancing amyloid species in human semen and underscore the dynamic nature of semen's HIV-enhancing activity. IMPORTANCE Semen, the most common vehicle for HIV transmission, enhances HIV infection in vitro, but how long it retains this activity has not been investigated. Semen

Reducing capital and operating costs in gas processing, liquefaction, and storage

Energy Technology Data Exchange (ETDEWEB)

Krusen, III, L C [Phillips Petroleum Co., Bartlesville, OK (United States). Research Div.

1997-06-01

The LNG industry is unanimous that capital costs must be reduced throughout the chain, and especially at the liquefaction facility including associated gas processing and LNG storage. The Ken ai LNG plant provides an example of how both reduced capital and operating costs were attained. This paper will cover cost production strategies that can be applied to liquefaction processes in general, and will than focus on their realization in the Phillips Optimized Cascade LNG process. The paper concludes that reduced LNG plant costs are attainable. (Author).

Reducing capital and operating costs in gas processing, liquefaction, and storage

International Nuclear Information System (INIS)

Krusen, L.C. III

1997-01-01

The LNG industry is unanimous that capital costs must be reduced throughout the chain, and especially at the liquefaction facility including associated gas processing and LNG storage. The Ken ai LNG plant provides an example of how both reduced capital and operating costs were attained. This paper will cover cost production strategies that can be applied to liquefaction processes in general, and will than focus on their realization in the Phillips Optimized Cascade LNG process. The paper concludes that reduced LNG plant costs are attainable. (Author)

Effects of Chloramphenicol Pretreatment on Xylazine/ketamine ...

African Journals Online (AJOL)

Keyword: Chloramphenicol, xylazine, ketamine, anaesthesia, cats. The effect of pretreatment with a single intramuscular (im) dose of chloramphenicol (10mg/kg) on the anaethesia induced with im injection of ketamine (25mg/kg) was investigated in five cats premedicated with im xylazine (1.0mg/kg) and atropine ...

An optimum cold end configuration for helium liquefaction cycles

International Nuclear Information System (INIS)

Minta, M.; Smith, J.L.

1984-01-01

This chapter examines the effect of the non-ideal behavior of helium at low temperature on the performance of helium liquefaction cycles. The effect is isolated by means of a continuum model for the precooling stage. The cold end losses are due primarily to the composite effect of the non-ideality of helium at low temperatures and the heat exchanger losses, in addition to the component losses fixed by the expander/compressor efficiencies. Topics considered include continuously distributed full-pressure ratio expanders, continuously distributed full-flow expanders, the heat exchange effect (ideal gas working fluid, real gas working fluid), and cold end configuration. The cold end configuration minimizes the cycle cold end losses

Rotating disk atomization of Gd and Gd-Y for hydrogen liquefaction via magnetocaloric cooling

Energy Technology Data Exchange (ETDEWEB)

Slinger, Tyler [Iowa State Univ., Ames, IA (United States)

2016-12-17

In order to enable liquid hydrogen fuel cell technologies for vehicles the cost of hydrogen liquefaction should be lowered. The current method of hydrogen liquefaction is the Claude cycle that has a figure of merit (FOM) of 0.3-0.35. New magnetocaloric hydrogen liquefaction devices have been proposed with a FOM>0.5, which is a significant improvement. A significant hurdle to realizing these devices is the synthesis of spherical rare earth based alloy powders of 200μm in diameter. In this study a centrifugal atomization method that used a rotating disk with a rotating oil quench bath was developed to make gadolinium and gadolinium-yttrium spheres. The composition of the spherical powders included pure Gd and Gd_0.91Y_0.09. The effect of atomization parameters, such as superheat, melt properties, disk shape, disk speed, and melt system materials and design, were investigated on the size distribution and morphology of the resulting spheres. The carbon, nitrogen, and oxygen impurity levels also were analyzed and compared with the magnetic performance of the alloys. The magnetic properties of the charge material as well as the resulting powders were measured using a vibrating sample magnetometer. The saturation magnetization and Curie temperature were the target properties for the resulting spheres. These values were compared with measurements taken on the charge material in order to investigate the effect of atomization processing on the alloys.

Shear-wave velocity-based probabilistic and deterministic assessment of seismic soil liquefaction potential

Science.gov (United States)

Kayen, R.; Moss, R.E.S.; Thompson, E.M.; Seed, R.B.; Cetin, K.O.; Der Kiureghian, A.; Tanaka, Y.; Tokimatsu, K.

2013-01-01

Shear-wave velocity (Vs) offers a means to determine the seismic resistance of soil to liquefaction by a fundamental soil property. This paper presents the results of an 11-year international project to gather new Vs site data and develop probabilistic correlations for seismic soil liquefaction occurrence. Toward that objective, shear-wave velocity test sites were identified, and measurements made for 301 new liquefaction field case histories in China, Japan, Taiwan, Greece, and the United States over a decade. The majority of these new case histories reoccupy those previously investigated by penetration testing. These new data are combined with previously published case histories to build a global catalog of 422 case histories of Vs liquefaction performance. Bayesian regression and structural reliability methods facilitate a probabilistic treatment of the Vs catalog for performance-based engineering applications. Where possible, uncertainties of the variables comprising both the seismic demand and the soil capacity were estimated and included in the analysis, resulting in greatly reduced overall model uncertainty relative to previous studies. The presented data set and probabilistic analysis also help resolve the ancillary issues of adjustment for soil fines content and magnitude scaling factors.

Characteristics of the products of hydrothermal liquefaction combined with cellulosic bio-ethanol process

International Nuclear Information System (INIS)

Li, Rundong; Xie, Yinghui; Yang, Tianhua; Li, Bingshuo; Zhang, Yang; Kai, Xingping

2016-01-01

The integration utilization of fermentation residues from cellulosic bio-ethanol has attracted a great deal of attention to balance the total cost of bio-ethanol production while simultaneously dealing with bio-ethanol wastewater. A process of hydrothermal liquefaction (HTL) of intact materials from cellulosic bio-ethanol in a batch reactor was proposed. The effects of the reaction temperature and time on the liquefaction characteristics were examined. The optimum condition for liquefaction fermentation residues was 370 °C (21.25 MPa) and 30 min with a bio-oil yield of 40.79 wt%. GC-MS results indicated that the major chemical species in the bio-oil were phenols, ketones, long-chain hydrocarbons and fatty acids. Supercritical conditions (375 °C, 23.50 MPa) was favored for the low-molecular-weight species formation compared to subcritical conditions (370 °C, 21.25 MPa), as some long-chain species decreased. This work thus can provide a novel idea for bio-oil production from HTL of cellulosic bio-ethanol fermentation residues. - Highlights: • Bio-oil production via HTL combined with cellulosic bio-ethanol process was proposed. • Optimum condition for HTL of materials from cellulosic bio-ethanol was 370 °C and 30 min. • Bio-oil contained higher content of hydrocarbons and lower contents of organic acids.

Process Water Recycle in Hydrothermal Liquefaction of Microalgae To Enhance Bio-oil Yield

NARCIS (Netherlands)

Ramos-Tercero, E.A.; Bertucco, A.; Brilman, Derk Willem Frederik

2015-01-01

In this work, the effect of recycling the process water (PW) of hydrothermal liquefaction (HTL) to the HTL reactor was investigated, with the objective being to recover carbon from the organic content of the PW and to develop a solvent-free process. When recycling twice the PW at 220, 240, and 265

Process intensification effect of ball milling on the hydrothermal pretreatment for corn straw enzymolysis

International Nuclear Information System (INIS)

Yuan, Zhengqiu; Long, Jinxing; Wang, Tiejun; Shu, Riyang; Zhang, Qi; Ma, Longlong

2015-01-01

Highlights: • Novel pretreatment of ball milling combined with hydrothermal method was presented. • Intensification effect of ball milling was significant for corn straw enzymolysis. • Ball milling destroyed the physical structure of corn straw. • Chemical (liquid mixture) method removed lignin and hemicellulose. • Glucose yield increased from 0.41 to 13.86 mg mL −1 under the optimized condition. - Abstract: Enhancement of the cellulose accessibility is significant for biomass enzymatic hydrolysis. Here, we reported an efficient combined pretreatment for corn straw enzymolysis using ball milling and dilute acid hydrothermal method (a mixture solvent of H 2 O/ethanol/sulfuric acid/hydrogen peroxide liquid). The process intensification effect of ball milling on the pretreatment of the corn straw was studied through the comparative characterization of the physical–chemical properties of the raw and pretreated corn straw using FT-IR, BET, XRD, SEM, and HPLC analysis. The effect of the pretreatment temperature was also investigated. Furthermore, various pretreatment methods were compared as well. Moreover, the pretreatment performance was measured by enzymolysis. The results showed that ball milling had a significant process intensification effect on the corn straw enzymolysis. The glucose concentration was dramatically increased from 0.41 to 13.86 mg mL −1 after the combined treatment of ball milling and hydrothermal. The efficient removal of lignin and hemicellulose and the enlargement of the surface area were considered to be responsible for this significant increase based on the intensive analysis on the main components and the physical–chemical properties of the raw and pretreated corn straw

Studies on characteristics of fluid dynamics in the coal liquefaction reactor; Sekitan ekika hanno tonai no ryudo tokusei

Energy Technology Data Exchange (ETDEWEB)

Sakawaki, K.; Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan); Mochizuki, M.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Tachikawa, N.; Moki, T.; Ishikawa, I. [Japan Atomic Energy Research Institute, Tokyo (Japan)

1996-10-28

To design the coal liquefaction reactor of large scale plant in future, it is important to understand characteristics of fluid dynamics within the coal liquefaction reactor. In this study, to measure the fluid dynamics of liquid phase within the coal liquefaction reactor operated under high temperature and high pressure coal liquefaction condition, neutron attenuating tracer (NAT) technique, one of the tracer test methods, was applied using 1 t/d coal treating PSU. The residence time of liquid phase within the reactor can be measured by utilizing property of neutron of being absorbed by materials. The tracer was injected at the inlets of first and third reactors, and the neutron was counted at each outlet. The concentration of tracer was derived from the discrete value, to determine the residence time distribution of liquid phase. The mean residence time of liquid phase in the single first reactor and in the total three reactors were prolonged under the severe operation conditions of liquefaction. The more severe the liquefaction operation condition was, the more active the mixing of liquid phase was in the first reactor. It was found that the progress of reaction was accelerated. 2 refs., 5 figs., 1 tab.

Process and analytical studies of enhanced low severity co-processing using selective coal pretreatment

Energy Technology Data Exchange (ETDEWEB)

Baldwin, R.M.; Miller, R.L.

1991-12-01

The findings in the first phase were as follows: 1. Both reductive (non-selective) alkylation and selective oxygen alkylation brought about an increase in liquefaction reactivity for both coals. 2. Selective oxygen alkylation is more effective in enhancing the reactivity of low rank coals. In the second phase of studies, the major findings were as follows: 1. Liquefaction reactivity increases with increasing level of alkylation for both hydroliquefaction and co-processing reaction conditions. 2. the increase in reactivity found for O-alkylated Wyodak subbituminous coal is caused by chemical changes at phenolic and carboxylic functional sites. 3. O-methylation of Wyodak subbituminous coal reduced the apparent activation energy for liquefaction of this coal.

Soil Improvement By Jet Grout Method And Geogrid Against Liquefaction: Example Of Samsun-Tekkeköy

Science.gov (United States)

Öztürk, Seda; Banu İkizler, S.; Şadoǧlu, Erol; Dadaşbilge, Ozan; Angın, Zekai

2017-04-01

scenarios of earthquakes with 6.0, 6.5, 7.0 and 7.2 magnitudes. As a result of the analyses made, it has been deemed necessary to improve the soil in order to prevent or reduce the liquefaction effects which may occur in a possible earthquake due to the presence of liquefaction potential in the research area. For this purpose, jet grouting method and geogrid fill system, which are used widely in Turkey, have been chosen as appropriate improvement methods. Geogrids are strong in tension so they are commonly used to reinforce subsoils below foundations. Additionally, jet grouting method provides high bearing capacity; it is solution to the settlement problems, it can be applied to almost any kind of soil and it has a short production period. Within this scope, optimal solution was obtained with 616 pieces of 8 m and 12 m jet grout columns with the diameter of 0.65 m and with geogrid mechanical fillings laid on jet grout columns. Thus, not only the risk of liquefaction was eliminated but also an improvement of more than 3 times of the bearing capacity of the foundation was acquired. In addition, the required quality control tests were carried out for the jet grout columns built in the research area and no adverse effects were observed. Key words: Liquefaction, soil improvement, jet grouting, geogrid

The effectiveness of pretreatment physics plan review for detecting errors in radiation therapy

International Nuclear Information System (INIS)

Gopan, Olga; Zeng, Jing; Novak, Avrey; Nyflot, Matthew; Ford, Eric

2016-01-01

Purpose: The pretreatment physics plan review is a standard tool for ensuring treatment quality. Studies have shown that the majority of errors in radiation oncology originate in treatment planning, which underscores the importance of the pretreatment physics plan review. This quality assurance measure is fundamentally important and central to the safety of patients and the quality of care that they receive. However, little is known about its effectiveness. The purpose of this study was to analyze reported incidents to quantify the effectiveness of the pretreatment physics plan review with the goal of improving it. Methods: This study analyzed 522 potentially severe or critical near-miss events within an institutional incident learning system collected over a three-year period. Of these 522 events, 356 originated at a workflow point that was prior to the pretreatment physics plan review. The remaining 166 events originated after the pretreatment physics plan review and were not considered in the study. The applicable 356 events were classified into one of the three categories: (1) events detected by the pretreatment physics plan review, (2) events not detected but “potentially detectable” by the physics review, and (3) events “not detectable” by the physics review. Potentially detectable events were further classified by which specific checks performed during the pretreatment physics plan review detected or could have detected the event. For these events, the associated specific check was also evaluated as to the possibility of automating that check given current data structures. For comparison, a similar analysis was carried out on 81 events from the international SAFRON radiation oncology incident learning system. Results: Of the 356 applicable events from the institutional database, 180/356 (51%) were detected or could have been detected by the pretreatment physics plan review. Of these events, 125 actually passed through the physics review; however

The effectiveness of pretreatment physics plan review for detecting errors in radiation therapy

Energy Technology Data Exchange (ETDEWEB)

Gopan, Olga; Zeng, Jing; Novak, Avrey; Nyflot, Matthew; Ford, Eric, E-mail: eford@uw.edu [Department of Radiation Oncology, University of Washington Medical Center, 1959 NE Pacific Street, Box 356043, Seattle, Washington 98195 (United States)

2016-09-15

Purpose: The pretreatment physics plan review is a standard tool for ensuring treatment quality. Studies have shown that the majority of errors in radiation oncology originate in treatment planning, which underscores the importance of the pretreatment physics plan review. This quality assurance measure is fundamentally important and central to the safety of patients and the quality of care that they receive. However, little is known about its effectiveness. The purpose of this study was to analyze reported incidents to quantify the effectiveness of the pretreatment physics plan review with the goal of improving it. Methods: This study analyzed 522 potentially severe or critical near-miss events within an institutional incident learning system collected over a three-year period. Of these 522 events, 356 originated at a workflow point that was prior to the pretreatment physics plan review. The remaining 166 events originated after the pretreatment physics plan review and were not considered in the study. The applicable 356 events were classified into one of the three categories: (1) events detected by the pretreatment physics plan review, (2) events not detected but “potentially detectable” by the physics review, and (3) events “not detectable” by the physics review. Potentially detectable events were further classified by which specific checks performed during the pretreatment physics plan review detected or could have detected the event. For these events, the associated specific check was also evaluated as to the possibility of automating that check given current data structures. For comparison, a similar analysis was carried out on 81 events from the international SAFRON radiation oncology incident learning system. Results: Of the 356 applicable events from the institutional database, 180/356 (51%) were detected or could have been detected by the pretreatment physics plan review. Of these events, 125 actually passed through the physics review; however

Effect of ultrasonic pretreatment on anaerobic digestion and its sludge dewaterability.

Science.gov (United States)

Xu, Huacheng; He, Pinjing; Yu, Guanghui; Shao, Liming

2011-01-01

To investigate the effect of ultrasonic pretreatment on anaerobic digestion and sludge dewaterability and further to probe into the influencing factors on sludge dewaterability, sludge flocs were stratified into four fractions: (1) slime; (2) loosely bound extracellular polymeric substances (LB-EPS); (3) tightly bound EPS (TB-EPS); and (4) EPS-free pellets. The results showed that ultrasonic pretreatment increased the anaerobic digestion efficiency by 7%-8%. Anaerobic digestion without ultrasonic pretreatment deteriorated the sludge dewaterability, with the capillary suction time (CST) increased from 1.42 to 47.3 (sec x L)/g-TSS. The application of ultrasonic pretreatment firstly deteriorated the sludge dewaterability (normalized CST increased to 44.4 (sec x L)/g-TSS), while subsequent anaerobic digestion offset this effect and ultimately decreased the normalized CST to 23.2 (sec x L)/g-TSS. The dewaterability of unsonicated sludge correlated with protein (p = 0.003) and polysaccharide (p = 0.004) concentrations in the slime fraction, while that of sonicated sludge correlated with protein concentrations in the slime and LB-EPS fractions (p anarobic digestion.

Effects of Pretreatments in Convective Dehydration of Rosehip (Rosa eglanteria

Directory of Open Access Journals (Sweden)

Alejandra Mabellini

2012-04-01

Full Text Available The aim of this work was to experimentally determine drying curves for thin layer and bed drying of rosehip fruits, with and without pretreatments, to reduce processing times as a function of drying air operating variables, to propose dehydration kinetics of fruits and to determine its kinetic parameters for further use within drying simulation software. Fruits were pre-treated both chemically and mechanically, which included dipping the fruits in NaOH and ethyl oleate solutions; and cutting or perforating the fruit cuticle, respectively. Simulation models were then adopted to fit the kinetics drying data considering fruit volume shrinkage. These simple models minimized the calculation time during the simulation of deep-bed driers. Results show that pre-treatments reduced processing times up to 57%, and evaluated models satisfactorily predicted the drying of rosehip fruit. Effective mass diffusion coefficients were up to 4-fold greater when fruit was submitted to mechanical pretreatments.

Novel use of residue from direct coal liquefaction process

Energy Technology Data Exchange (ETDEWEB)

Jianli Yang; Zhaixia Wang; Zhenyu Liu; Yuzhen Zhang [Chinese Academy of Sciences, Taiyuan (China). State Key Laboratory of Coal Conversion

2009-09-15

Direct coal liquefaction residue (DCLR) is, commonly, designed to be used as a feed stock for gasification or combustion. Use of DCLR as a value added product is very important for improving overall economy of direct coal liquefaction processes. This study shows that the DCLR may be used as a pavement asphalt modifier. The modification ability is similar to that of Trinidad Lake Asphalt (TLA), a superior commercial modifier. Asphalts modified by two DCLRs meet the specifications of ASTM D5710 and BSI BS-3690 designated for the TLA-modified asphalts. The required addition amount for the DCLRs tested is less than that for TLA due possibly to the high content of asphaltene in DCLRs. Different compatibility was observed for the asphalts with the same penetration grade but from the different origin. Different components in the DCLR play different roles in the modification. Positive synergetic effects among the fractions were observed, which may due to the formation of the stable colloid structure. Unlike polymer-type modifier, the structure of asphalt-type modifier has a similarity with petroleum asphalts which favors the formation of a stable dispersed polar fluid (DPF) colloid structure and improves the performance of pavement asphalt. 12 refs., 1 fig., 6 tabs.

Direct liquefaction proof-of-concept facility

Energy Technology Data Exchange (ETDEWEB)

Alfred G. Comolli; Peizheng Zhou; HTI Staff

2000-01-01

The main objective of the U.S. DOE, Office of Fossil Energy, is to ensure the US a secure energy supply at an affordable price. An integral part of this program was the demonstration of fully developed coal liquefaction processes that could be implemented if market and supply considerations so required, Demonstration of the technology, even if not commercialized, provides a security factor for the country if it is known that the coal to liquid processes are proven and readily available. Direct liquefaction breaks down and rearranges complex hydrocarbon molecules from coal, adds hydrogen, and cracks the large molecules to those in the fuel range, removes hetero-atoms and gives the liquids characteristics comparable to petroleum derived fuels. The current processes being scaled and demonstrated are based on two reactor stages that increase conversion efficiency and improve quality by providing the flexibility to adjust process conditions to accommodate favorable reactions. The first stage conditions promote hydrogenation and some oxygen, sulfur and nitrogen removal. The second stage hydrocracks and speeds the conversion to liquids while removing the remaining sulfur and nitrogen. A third hydrotreatment stage can be used to upgrade the liquids to clean specification fuels.

Post-cyclic behavior of low plasticity silt under full and limited liquefaction using triaxial compression testing.

Science.gov (United States)

2010-02-01

During an earthquake, liquefaction does not happen all the time. It depends on the duration and magnitude of the earthquake and the properties (with relationship to resistance of liquefaction) of the low plasticity silt. Under low duration or magnitu...

Comparative data on effects of leading pretreatments and enzyme loadings and formulations on sugar

Energy Technology Data Exchange (ETDEWEB)

Wyman, Charles [Univ. of California, Riverside, CA (United States); Balan, Venkatech [Michigan State Univ., East Lansing, MI (United States); Dale, Bruce E. [Michigan State Univ., East Lansing, MI (United States); Elander, Richard [National Renewable Energy Lab. (NREL), Golden, CO (United States); Falls, Matthew [Texas A & M Univ., College Station, TX (United States); Hames, Bonnie [Ceres Corporation, Thousand Oaks, CA (United States); Holtzapple, Mark [Texas A & M Univ., College Station, TX (United States); Ladisch, Michael R. [Purdue Univ., West Lafayette, IN (United States); Lee, Y. Y. [Auburn Univ., AL (United States); Mosier, Nathan [Purdue Univ., West Lafayette, IN (United States); Pallapolu, Venkata R. [Auburn Univ., AL (United States); Shi, Jian [Univ. of California, Riverside, CA (United States); Warner, Ryan E. [Genencor, Palo Alto, CA (United States)

2011-06-16

Dilute sulfuric acid (DA), sulfur dioxide (SO2), liquid hot water (LHW), soaking in aqueous ammonia (SAA), ammonia fiber expansion (AFEX), and lime pretreatments were applied to Alamo, Dacotah, and Shawnee switchgrass. Application of the same analytical methods and material balance approaches facil-itated meaningful comparisons of glucose and xylose yields from combined pretreatment and enzymatic hydrolysis. Use of a common supply of cellulase, beta-glucosidase, and xylanase also eased comparisons. All pretreatments enhanced sugar recovery from pretreatment and subsequent enzymatic hydrolysis substantially compared to untreated switchgrass. Adding beta-glucosidase was effective early in enzy-matic hydrolysis while cellobiose levels were high but had limited effect on longer term yields at the enzyme loadings applied. Adding xylanase improved yields most for higher pH pretreatments where more xylan was left in the solids. Harvest time had more impact on performance than switchgrass variety, and microscopy showed changes in different features could impact performance by different pretreatments.

Report on the achievements in research and development of a coal liquefaction technology in the Sunshine Project in fiscal 1981. Development of a solvent extraction and liquefaction plant (development of a 1-t/d experimental plant and research on the solvent extraction and liquefaction process); 1981 nendo sekitan ekika gijutsu no kenkyu kaihatsu, yozai chushutsu ekika plant no kaihatsu seika hokokusho. 1t/d jikken plant no kaihatsu (yozai chushutsu ekika process no kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Among the items of the solvent extraction and liquefaction plant technologies in the Sunshine Project in fiscal 1981, this paper describes the achievements in developing a 1-t/d experimental plant and the solvent extraction and liquefaction process. Basic facilities were completed by giving expansion constructions on the extraction reaction column, gas-liquid separation column, and hydrogenation reaction column. The operation was performed with the primary object placed on verifying the effect of measures on problems that have been extracted, and checking the solvent balance. The conversion rate at an extraction reaction temperature of 450 degrees C was 83%, agreeing with the result of the fundamental study. The solvent has turned light as a result of 153-hour continuous operation, but circulating use was possible. Progress of the reaction has become easily controllable in the hydrogenation system. Fundamental discussions were given on engineering aspects, which require further accumulation of data. In the research of the solvent extraction and liquefaction process, fiscal 1981 has performed discussions on liquefaction catalysts, and on the effect of the hydrogen donating solvents. The discussions were for the fundamental research to establish adequate conditions for the 1-t/d experimental plant by operating a small continuous operation facility to its full extent, and by using a batch type reaction device. Screening was also carried out on catalysts. (NEDO)

FY 1980 Report on results of Sunshine Project. Development of coal liquefaction techniques (Development of 1 T/D test plant, and researches on the solvent-extraction type liquefaction process); 1980 nendo sekitan ekika gijutsu no kaihatsu, yozai chushutsu ekika plant no kaihatsu seika hokokusho. 1t/nichi jikken plant no kaihatsu, yozai chushutsu ekika process no kenkyu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This program is aimed at establishing the techniques for solvent-extraction type coal liquefaction plant by constructing and operating a 1 T/D test plant to obtain the technical data for the efficient plant. The test plant is operated to confirm the effects of temperature and coal slurry concentration on liquefaction conversion by the solvent-extraction for a short time in the furnace for the extraction unit. The extraction type coal liquefaction tests can be conducted for a reaction time of around 1 hour by the test plant. The recycled solvent purification unit is installed, to regenerate the hydrogen donor solvent. For researches on the solvent-extraction type coal liquefaction process, the continuous extraction is conducted, to investigate the effects of extraction reaction rate at relatively low pressure. The optimum hydrogenation conditions are studied for the test plant. It is confirmed that a Mo-based catalyst is suitable for the hydrogenation. The batch type reaction system is operated to investigate the liquid yield of Wandoan coal, and recycled solvent balances and compositions. (NEDO)

Effect of Various Pretreatments on Quality Attributes of Vacuum-Fried Shiitake Mushroom Chips

Directory of Open Access Journals (Sweden)

Aiqing Ren

2018-01-01

Full Text Available The objective of this study is to investigate the effects of pretreatments on the quality of vacuum-fried shiitake mushroom slices. Four different pretreatments addressed in this study were (1 blanching as control, (2 blanching and osmotic dehydration with maltodextrin (MD solution, (3 blanching, osmotic dehydration, and coating with sodium carboxymethyl cellulose (CMC, (4 blanching and osmotic dehydration, followed by freezing. All samples were pretreated and then fried in palm oil at 90°C with vacuum degree of −0.095 MPa for 30 min. The results showed that pretreatments significantly (p0.05 differences of fried chip in the texture among the four different pretreatments. The aw values of all the fried chips were less than 0.38, indicating that the products had a long shelf life. Therefore, the blanching, osmotic dehydration, and coating pretreatment before vacuum frying was the most suitable pretreatment for vacuum-fried shiitake mushroom chips.

Finite Element Modelling of Seismic Liquefaction in Soils

NARCIS (Netherlands)

Galavi, V.; Petalas, A.; Brinkgreve, R.B.J.

2013-01-01

Numerical aspects of seismic liquefaction in soils as implemented in the finite element code, PLAXIS, is described in this paper. After description of finite element equations of dynamic problems, three practical dynamic boundary conditions, namely viscous boundary tractions, tied degrees of freedom

Seismic behavior of breakwaters on complex ground by numerical tests: Liquefaction and post liquefaction ground settlements

Science.gov (United States)

Gu, Linlin; Zhang, Feng; Bao, Xiaohua; Shi, Zhenming; Ye, Guanlin; Ling, Xianzhang

2018-04-01

A large number of breakwaters have been constructed along coasts to protect humans and infrastructures from tsunamis. There is a risk that foundation soils of these structures may liquefy, or partially liquefy during the earthquake preceding a tsunami, which would greatly reduce the structures' capacity to resist the tsunami. It is necessary to consider not only the soil's liquefaction behavior due to earthquake motions but also its post-liquefaction behavior because this behavior will affect the breakwater's capacity to resist an incoming tsunami. In this study, numerical tests based on a sophisticated constitutive model and a soil-water coupled finite element method are used to predict the mechanical behavior of breakwaters and the surrounding soils. Two real breakwaters subjected to two different seismic excitations are examined through numerical simulation. The simulation results show that, earthquakes affect not only the immediate behavior of breakwaters and the surrounding soils but also their long-term settlements due to post-earthquake consolidation. A soil profile with thick clayey layers beneath liquefied soil is more vulnerable to tsunami than a soil profile with only sandy layers. Therefore, quantitatively evaluating the seismic behavior of breakwaters and surrounding soils is important for the design of breakwater structures to resist tsunamis.

Comparison of FeS, FeS + S and solid superacid catalytic properties for coal hydro-liquefaction

Energy Technology Data Exchange (ETDEWEB)

Zhicai Wang; Hengfu Shui; Dexiang Zhang; Jinsheng Gao [East China University of Science and Technology, Shanghai (China). College of Resource and Environment Engineering

2007-03-15

Catalyst plays an important role in direct coal liquefaction. This paper focuses on the catalytic behavior of a novel SO{sub 4}{sup 2-}/ZrO{sub 2} superacid catalyst in coal hydro-liquefaction. A series of hydro-liquefaction experiments were conducted under mild conditions - 400{sup o}C, 30 min and H{sub 2} initial pressure 4 MPa in a batch autoclave with a volume of 100 ml. The catalytic property of SO{sub 4}{sup 2-}/ZrO{sub 2} was compared with FeS and FeS + S by Shenhua coal. The liquefaction products catalyzed by different catalysts were analyzed by FTIR spectrum, {sup 1}H NMR spectrum and element analysis. In addition, the SO{sub 4}{sup 2-}/ZrO{sub 2} solid superacid was characterized. The results indicated that the SO{sub 4}{sup 2-}/ZrO{sub 2} solid superacid shows outstanding catalytic property for direct liquefaction of coal and gives the highest coal conversion and gas + oil yield compared to other two catalysts. The THF conversion and the extraction yield of CS{sub 2}/NMP mixed solvent of liquefied coal catalyzed with SO{sub 4}{sup 2-}/ZrO{sub 2} are 76.3%, daf and 81.2%, daf respectively, and the yield of gas + oil is 62.5%, daf under the condition used in this study. The pyrolysis of coal macromolecular clusters can be promoted by catalysts such as FeS, FeS + S and SO{sub 4}{sup 2-}/ZrO{sub 2}. There may be only the pyrolysis of volatile matter and the relaxation of the structure of coal macromolecular clusters in non-catalytic liquefaction at 400{sup o}C. Added sulfur in FeS can improve the catalytic activity of hydrogenation. SO{sub 4}{sup 2-}/ZrO{sub 2} is a notable catalyst in the study of coal direct liquefaction because it shows excellent catalytic activities for the pyrolysis and the hydrogenation. In addition, it has been found that the C-O bond is the most stable group in coal liquefaction reaction except for the covalent bond between carbon and carbon. 34 refs., 6 figs., 6 tabs.

Coal liquefaction still a dream

Energy Technology Data Exchange (ETDEWEB)

Overberg, H

1982-03-19

Liquefaction of coal is not profitable in West Germany and will not be so far some time to coal. This is true for West German and imported coal. The result may be improved but not changed by combined conversion of coal and top residues of distilleries. These are the main statements of a study carried out by Messrs. Veba Oel AG, Gelsenkirchen, on behalf of the Federal Minister for Research and Technology. The results of the study are presented in 20 volumes.

Electrical resistivity tomography for studying liquefaction induced by the May 2012 Emilia-Romagna earthquake (Mw = 6.1, northern Italy)

Science.gov (United States)

Giocoli, A.; Quadrio, B.; Bellanova, J.; Lapenna, V.; Piscitelli, S.

2014-04-01

This work shows the result of an electrical resistivity tomography (ERT) survey carried out for imaging and characterizing the shallow subsurface affected by the coseismic effects of the Mw = 6.1 Emilia-Romagna (northern Italy) earthquake that occurred on 20 May 2012. The most characteristic coseismic effects were ground failure, lateral spreading and liquefaction that occurred extensively along the paleo-Reno River in the urban areas of San Carlo and Mirabello (southwestern portion of Ferrara Province). In total, six electrical resistivity tomographies were performed and calibrated with surface geological surveys, exploratory boreholes and aerial photo interpretations. This was one of first applications of the electrical resistivity tomography method in investigating coseismic liquefaction.

Electrical resistivity tomography for studying liquefaction induced by the May 2012 Emilia-Romagna earthquake (Mw = 6.1, North Italy)

Science.gov (United States)

Giocoli, A.; Quadrio, B.; Bellanova, J.; Lapenna, V.; Piscitelli, S.

2013-10-01

This work shows the result of an Electrical Resistivity Tomography survey carried out for imaging and characterizing the shallow subsurface affected by the coseismic effects of the Mw = 6.1 Emilia-Romagna (North Italy) earthquake occurred on 20 May 2012. The most characteristic coseismic effects were ground failure, lateral spreading and liquefaction that occurred extensively along the paleo-Reno river in the urban areas of San Carlo, a hamlet of Sant'Agostino municipality, and of Mirabello (south-western portion of the Ferrara Province). Totally, six Electrical Resistivity Tomography were performed and calibrated with surface geological surveys, exploratory borehole and aerial photo interpretations. This was one of the first applications of the Electrical Resistivity Tomography method in investigating coseismic liquefaction.

Effect of pretreatment of molasses and recycling of yeast on ethanol fermentation

Energy Technology Data Exchange (ETDEWEB)

Samaniego, R; Srivastas, R L

1971-01-01

The effect of pretreatment of molasses and recycling yeast for the removal of calcium, potassium, coloring matter, and colloidal substances on the production of ethanol from the fermentation of molasses was studied. Highest yield of ethanol (9.1%) was obtained from molasses pretreated with egg albumin followed by the treatment with ethanol(8.5%) and H/sub 2/SO/sub 4/ (8.1%) as compared to control (7.9%). Pretreatment with Al/sub 2/(SO/sub 4/)/sub 3/ and activated C did not improve yield. Lowest yield was recorded with tartaric acid. The washing of yeast with HCl (pH 3.5) resulted in higher yields of ethanol as compared to control in all stages of recyclings. Pretreatment of yeast with 5% NaCl retarded the fermentation rate and caused low yield of ethanol. A combined effect of H/sub 2/SO/sub 4/ and HCl showed no essential difference in yields of ethanol except in the third recycling.

SUMMARY REPORT OF THE DOE DIRECT LIQUEFACTION PROCESS DEVELOPMENT CAMPAIGN OF THE LATE TWENTIETH CENTURY; FINAL

International Nuclear Information System (INIS)

F.P. Burke; S.D. Brandes; D.C. McCoy; R.A. Winschel; D. Gray; G. Tomlinson

2001-01-01

Following the petroleum price and supply disruptions of 1973, the U.S. government began a substantial program to fund the development of alternative fuels. Direct coal liquefaction was one of the potential routes to alternative fuels. The direct coal liquefaction program was funded at substantial levels through 1982, and at much lower levels thereafter. Those processes that were of most interest during this period were designed to produce primarily distillate fuels. By 1999, U.S. government funding for the development of direct coal liquefaction ended. Now that the end of this campaign has arrived, it is appropriate to summarize the process learnings derived from it. This report is a summary of the process learnings derived from the DOE direct coal liquefaction process development campaign of the late twentieth century. The report concentrates on those process development programs that were designed to produce primarily distillate fuels and were largely funded by DOE and its predecessors in response to the petroleum supply and price disruptions of the 1970s. The report is structured as chapters written by different authors on most of the major individual DOE-funded process development programs. The focus of the report is process learnings, as opposed to, say, fundamental coal liquefaction science or equipment design. As detailed in the overview (Chapter 2), DOE's direct coal liquefaction campaign made substantial progress in improving the process yields and the quality of the distillate product. Much of the progress was made after termination by 1983 of the major demonstration programs of the ''first generation'' (SRC-II, H-Coal, EDS) processes

Determination of Liquefaction Potential using Artificial Neural Networks

DEFF Research Database (Denmark)

Farrokhzad, F; Choobbasti, A.J; Barari, Amin

2011-01-01

The authors propose an alternative general regression model based on neural networks, which enables analysis of summary data obtained by liquefaction analysis according to usual methods. For that purpose, the data from some thirty boreholes made during field investigations in Babol, in the Iranian...

Effect of properties of iron compounds on the catalytic activity in direct coal liquefaction; Tetsu kagobutsu no keitai to sekitan ekika kassei

Energy Technology Data Exchange (ETDEWEB)

Kaneko, T.; Tazawa, K. [Mitsubishi Chemical Corp., Tokyo (Japan); Shimasaki, K. [Kobe Steel Ltd. (Japan)

1998-08-20

When considering merchandising scale of the coal liquefaction process, it is a preliminary condition that metal used for its catalyst is rich in resource volume, cheap in production cost, without pollution, and so forth, and application of cheap iron ore and ferrous compounds to disposable catalyst is desired. As liquefaction activity of the iron ore was hitherto improved by its micro crushing, its mechanical crush had a limit of about 2 {mu}m in mean particle diameter. However, together with recent crushing technique, crushers with high performance were developed, and then micro crushing by sub-micron became possible industri8ally even for iron ore. In this study, three kinds of Australian iron ores such as limonite of ferric hydroxide type iron ore, pyrite of ferrous sulfide type, and hematite of ferric oxide type were micro crushed to examine coal liquefaction activity and hydrogenation reaction activity of 1-methyl naphthalene (1-MN) and also relationship between properties and activity of catalyst for the latter before and after reaction. 11 refs., 8 figs., 5 tabs.

Effect of plasma pretreatment on the structure and emission characteristics of carbon nanotubes

International Nuclear Information System (INIS)

Uh, Hyung Soo; Lee, Soo Myun; Choi, Seok Rim; Park, Sang Sik; Cho, Euo Sik; Lee, Jong Duk; Kwon, Sang Jik

2003-01-01

Carbon nanotubes (CNTs) were grown on Ni-coated TiN/Si substrates by using microwave plasma chemical vapor deposition with a gas mixture of H 2 /CH 4 at a low temperature of 500 .deg. C. The effect of H 2 plasma pretreatment on the diameter of grown CNTs was investigated. We found that the average diameter of CNTs could be easily controlled by using the H 2 -plasma pretreatment time before CNTs growth and varied from 36 nm to 26 nm as the pretreatment time changed from 5 min to 15 min. However, any further increase in the pretreatment time gave rise to a rapid decrease in CNTs growth. After 25 min of the plasma pretreatment, scanning electron microscopy observation exhibited the destruction of the CNTs. The impact of the plasma pretreatment time on the emission behavior of CNTs was also investigated in a diode-type electron-emission configuration. The variation of the CNT diameter due to the plasma pretreatment caused a drastic change in emission properties. The turn-on voltages of CNT emitters varied from 3.5 V/μm to 9 V/μm, depending on the hydrogen-plasma pretreatment conditions. The close relationship between the electron-emission characteristics and the pretreatment time indicates that the pretreatment condition may be a key process parameter in CNTs growth for field-emission displays and should be optimized.

Assessment of materials selection and performance for direct-coal- liquefaction plants in the United States

Energy Technology Data Exchange (ETDEWEB)

Olsen, A.R.; Judkins, R.R.; Keiser, J.R.

1996-09-01

Several direct coal liquefaction processes have been demonstrated at the pilot plant level in the United States. Presently only one plant remains operational, namely, the Hydrocarbon Technologies, Inc., 4.0- ton-per-day process development unit in Lawrenceville, New Jersey. The period from 1974 to 1982 saw the greatest amount of development of direct coal liquefaction in the United States with four major pilot plants being devoted to variants of this technology. The plants included the SRC-I plant at Wilsonville, Alabama, which operated from 1974 to 1992; the SRC-I/II plant at Fort Lewis, Washington, which operated from 1974 to 1981; the H-Coal plant at Catlettsburg, Kentucky, which operated from 1980 to 1982; and the Exxon Coal Liquefaction Pilot Plant at Baytown, Texas, which operated from 1980 to 1982. Oak Ridge National Laboratory scientists and engineers were actively involved in many phases and technical disciplines at all four of these plants, especially in materials testing, evaluation, and failure analyses. In addition, ORNL materials scientists and engineers conducted reviews of the demonstration and commercial plant designs for materials selections. The ORNL staff members worked closely with materials engineers at the pilot plants in identifying causes of materials degradation and failures, and in identifying solutions to these problems. This report provides a comprehensive summary of those materials activities. Materials performance data from laboratory and coal liquefaction pilot plant tests, failure analyses, and analyses of components after use in pilot plants were reviewed and assessed to determine the extent and causes of materials degradation in direct coal liquefaction process environments. Reviews of demonstration and commercial plant design documents for materials selections were conducted. These reviews and assessments are presented to capture the knowledge base on the most likely materials of construction for direct coal liquefaction plants.

Japan`s New Sunshine Project. 1996 Annual Summary of Coal Liquefaction and Gasification; 1996 nendo new sunshine keikaku seika hokokusho gaiyoshu. Sekitan no ekika gasuka

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-11-01

In reference to the results of the research and development under the fiscal 1996 New Sunshine Project, a report was summed up on coal liquefaction and coal gasification. As to the R and D of coal liquefaction technology, researches were conducted on liquefaction characteristics and engineering properties by coal kind, catalysts for coal liquefaction, liquefaction reaction of coal and reformation utilization of the liquefied products, liquefaction reaction mechanism and coking mechanism, solubility of coal in solvent and catalytic reaction mechanism, solvent reaction mechanism by hydrogen donor solvent, etc. Concerning the R and D of coal gasification technology, made were the basic study of eco-technology adaptable gasification technology and the study of coal gasification enhancing technology. Further, as to the development of bituminous coal liquefaction technology, carried out were the study in pilot plants and the support study of pilot plants. Additionally, R and D were done of the basic technology of coal liquefaction such as upgrading technology and environmentally acceptable coal liquefaction technology, and of coal hydrogasification technology. 3 refs., 81 figs., 25 tabs.

Comparison of Microwave and Ozonolysis Effect as Pretreatment on Sugarcane Bagasse Enzymatic Hydrolysis

Directory of Open Access Journals (Sweden)

N Eqra

2015-03-01

Full Text Available Bioethanol production from agricultural residues is one of the promising methods. Pretreatment is the most important step in this type of bioethanol production. In this study, the saccharification percentage of sugarcane bagasse was investigated after two types of pretreatments including ozone steaming and microwave. Microwave pretreatment was studied with two factors of microwave radiation (170, 450, and 850 w and microwave duration (2, 6, and 10 min. The ozonolysis (ozone steaming pretreatment was surveyed with two factors of moisture content of bagasse (30, 40, and 50% and ozonolysis time (1.5, 2.5, 3.5, and 4.5 hr. After hydrolysis, the Saccharification percentage of sugarcane bagasse increased to 57.2% and 67.06% with microwave and ozonolysis pretreatments, respectively; compare to 20.85% in non-ozonated bagasse. It can be concluded that the ozonolysis is the most effective pretreatment regarding to saccharification percentage of sugarcane bagasse.

Efficient direct coal liquefaction of a premium brown coal catalyzed by cobalt-promoted fumed oxides

Energy Technology Data Exchange (ETDEWEB)

Trautmann, M.; Loewe, A.; Traa, Y. [Stuttgart Univ. (Germany). Inst. of Chemical Technology

2013-11-01

The search for alternatives in the fuel sector is an important technological challenge. An interim solution could be provided by direct coal liquefaction. Hydrogen economy and the lack of an efficient catalyst are the main obstacles for this process. We used a premium German brown coal with a high H/C molar ratio of 1.25 and nanostructured cobalt catalysts to improve the efficiency of direct coal liquefaction. We were able to recover and recycle the catalyst efficiently and reached good brown coal conversions and oil yields with single-stage coal liquefaction. The oil quality observed almost reached that of a conventional crude oil considering higher heating value (HHV), H/C molar ratio and aliphatic content. (orig.)

Coal liquefaction with preasphaltene recycle

Science.gov (United States)

Weimer, Robert F.; Miller, Robert N.

1986-01-01

A coal liquefaction system is disclosed with a novel preasphaltene recycle from a supercritical extraction unit to the slurry mix tank wherein the recycle stream contains at least 90% preasphaltenes (benzene insoluble, pyridine soluble organics) with other residual materials such as unconverted coal and ash. This subject process results in the production of asphaltene materials which can be subjected to hydrotreating to acquire a substitute for No. 6 fuel oil. The preasphaltene-predominant recycle reduces the hydrogen consumption for a process where asphaltene material is being sought.

Deoxy-liquefaction of three different species of macroalgae to high-quality liquid oil.

Science.gov (United States)

Li, Jinhua; Wang, Guoming; Chen, Ming; Li, Jiedong; Yang, Yaoyao; Zhu, Qiuyan; Jiang, Xiaohuan; Wang, Zonghua; Liu, Haichao

2014-10-01

Three species of macroalgae (Ulva lactuca, Laminaria japonica and Gelidium amansii) were converted into liquid oils via deoxy-liquefaction. The elemental analysis, FTIR and GC-MS results showed that the three liquid oils were all mainly composed of aromatics, phenols, alkanes and alkenes, other oxygen-containing compounds, and some nitrogen-containing compounds though there were some differences in terms of their types or contents due to the different constituents in the macroalgae feedstocks. The oxygen content was only 5.15-7.30% and the H/C molar ratio was up to 1.57-1.73. Accordingly, the HHV of the three oils were 42.50, 41.76 and 40.00 MJ/kg, respectively. The results suggested that U. lactuca, L. japonica and G. amansii have potential as biomass feedstock for fuel and chemicals and that deoxy-liquefaction technique may be an effective way to convert macroalgae into high-quality liquid oil. Copyright © 2014 Elsevier Ltd. All rights reserved.

A review on hydrothermal pre-treatment technologies and environmental profiles of algal biomass processing.

Science.gov (United States)

Patel, Bhavish; Guo, Miao; Izadpanah, Arash; Shah, Nilay; Hellgardt, Klaus

2016-01-01

The need for efficient and clean biomass conversion technologies has propelled Hydrothermal (HT) processing as a promising treatment option for biofuel production. This manuscript discussed its application for pre-treatment of microalgae biomass to solid (biochar), liquid (biocrude and biodiesel) and gaseous (hydrogen and methane) products via Hydrothermal Carbonisation (HTC), Hydrothermal Liquefaction (HTL) and Supercritical Water Gasification (SCWG) as well as the utility of HT water as an extraction medium and HT Hydrotreatment (HDT) of algal biocrude. In addition, the Solar Energy Retained in Fuel (SERF) using HT technologies is calculated and compared with benchmark biofuel. Lastly, the Life Cycle Assessment (LCA) discusses the limitation of the current state of art as well as introduction to new potential input categories to obtain a detailed environmental profile. Copyright © 2015 Elsevier Ltd. All rights reserved.

Effects of embryo induction media and pretreatments in isolated ...

African Journals Online (AJOL)

STORAGESEVER

2009-11-16

Nov 16, 2009 ... chemical + heat and also the effects of 5 embryo induction media (NPB-99, C17, ... Key words: Hexaploid wheat, haploid, isolated microspore culture, pretreatment, ..... this method is influenced by several mentioned factors.

Effect of pretreatment on purple-fleshed sweet potato flour for cake making

Science.gov (United States)

Hutasoit, M. S.; Julianti, E.; Lubis, Z.

2018-02-01

The purple-fleshed sweet-potato (PFSP) flour was produced by varying pretreatment of washed chips: dipping in 0.5 and 1.0% (w/v) citric acid solution for 30 min, dipping in 0.5 and 1.0% (w/v) citric acid solution for 30 min and followed by steam blanching for 5 min. The pretreatment effect on cake quality was investigated. The results showed that PFSP flour produced from pretreatment with dipping in 0.5% citric acid for 30 min followed by steam blanching for 5 min had higher lightness (L*) value and lower browning index, higher hedonic value of color and aroma and baking expansion. The specific volume of cake from pretreated flour, untreated flour and wheat flour were 44.87, 43.83, and 50.43cm3/g, respectively. The sensory evaluation of cake indicated that cake from pretreated PFSP flour was acceptable compare to those of cake from wheat flour.

Survival of Legionella in earthquake-induced soil disturbance (liquefaction) in residential areas, Christchurch, New Zealand: implications for disease.

Science.gov (United States)

Graham, Frances F; Harte, David Jg

2017-05-12

To investigate a possible link between liquefaction dust exposure and the noticeable increase in legionellosis cases in response to major earthquakes in 2010 and 2011 that resulted in widespread soil disturbance (liquefaction) in parts of Christchurch, New Zealand. We culture tested liquefaction-affected soil for Legionella spp. in the six months following the first earthquake in 2010. Thirty silt samples were collected randomly from locations within Christchurch's metropolitan area that were affected by liquefaction. The samples were tested to determine the presence of Legionella using qualitative and quantitative methods. Liquefaction-affected soil samples from three sites were further subjected to particle size distribution analysis and determination of major oxides. A controlled field study was established using six silt samples and one control (commercial compost), seeded with a wild-type strain of Legionella bozemanae serogroup (sg) 1 and persistence monitored over a 60-day period by culturing for the presence of Legionella. Dry matter determinations were undertaken so that total Legionella could be calculated on a dry weight basis. Legionella bacteria were undetectable after day one in the silt samples. However, L. bozemanae sg1 was detected in the control sample for the entire study period. This study showed that the liquefaction-affected soil could not contribute directly to the observed increase in legionellosis cases after the earthquakes due to its inability to support growth and survival of the Legionella bacteria.

Liquefaction induced by modern earthquakes as a key to paleoseismicity: A case study of the 1988 Saguenay event

International Nuclear Information System (INIS)

Tuttle, M.; Cowie, P.; Wolf, L.

1992-01-01

Liquefaction features, including sand dikes, sills, and sand-filled craters, that formed at different distances from the epicenter of the 1988 (Mw 5.9) Saguenay earthquake are compared with one another and with older features. Modern liquefaction features decrease in size with increasing distance from the Saguenay epicenter. This relationship suggests that the size of liquefaction features may be used to determine source zones of past earthquakes and to estimate attenuation of seismic energy. Pre-1988 liquefaction features are cross-cut by the 1988 features. Although similar in morphology to the modern features, the pre-1988 features are more weathered and considerably larger in size. The larger pre-1988 features are located in the Ferland area, whereas the smallest pre-1988 feature occurs more than 37 km to the southwest. This spatial distribution of different size features suggests that an unidentified earthquake source zone (in addition to the one that generated the Saguenay earthquake) may exist in the Laurentide-Saguenay region. Structural relationships of the liquefaction features indicate that one, possibly two, earthquakes induced liquefaction in the region prior to 1988. The age of only one pre-1988 feature is well-constrained at 340 ± 70 radiocarbon years BP. If the 1663 earthquake was responsible for the formation of this feature, this event may have been centered in the Laurentide-Saguenay region rather than in the Charlevoix seismic zone

Characteristics of process oils from HTI coal/plastics co-liquefaction runs

Energy Technology Data Exchange (ETDEWEB)

Robbins, G.A.; Brandes, S.D.; Winschel, R.A. [and others

1995-12-31

The objective of this project is to provide timely analytical support to DOE`s liquefaction development effort. Specific objectives of the work reported here are presented. During a few operating periods of Run POC-2, HTI co-liquefied mixed plastics with coal, and tire rubber with coal. Although steady-state operation was not achieved during these brief tests periods, the results indicated that a liquefaction plant could operate with these waste materials as feedstocks. CONSOL analyzed 65 process stream samples from coal-only and coal/waste portions of the run. Some results obtained from characterization of samples from Run POC-2 coal/plastics operation are presented.

Initial Earthquake Centrifuge Model Experiments for the Study of Liquefaction

National Research Council Canada - National Science Library

Steedman, R

1998-01-01

.... These are intended to gather data suitable for the development of improved design approaches for the prediction of liquefaction under earthquake loading using the new centrifuge facility at the WES...

An Advanced Wet Expansion Turbine for Hydrogen Liquefaction, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This proposal is responsive to NASA SBIR Topic X10.01, specifically, the need for efficient small- to medium-scale hydrogen liquefaction technologies including...

Nitrogen expander cycles for large capacity liquefaction of natural gas

Energy Technology Data Exchange (ETDEWEB)

Chang, Ho-Myung; Park, Jae Hoon; Gwak, Kyung Hyun [Hong Ik University, Department of Mechanical Engineering, Seoul, 121-791 (Korea, Republic of); Choe, Kun Hyung [Korea Gas Corporation, Incheon, 406-130 (Korea, Republic of)

2014-01-29

Thermodynamic study is performed on nitrogen expander cycles for large capacity liquefaction of natural gas. In order to substantially increase the capacity, a Brayton refrigeration cycle with nitrogen expander was recently added to the cold end of the reputable propane pre-cooled mixed-refrigerant (C3-MR) process. Similar modifications with a nitrogen expander cycle are extensively investigated on a variety of cycle configurations. The existing and modified cycles are simulated with commercial process software (Aspen HYSYS) based on selected specifications. The results are compared in terms of thermodynamic efficiency, liquefaction capacity, and estimated size of heat exchangers. The combination of C3-MR with partial regeneration and pre-cooling of nitrogen expander cycle is recommended to have a great potential for high efficiency and large capacity.

Nitrogen expander cycles for large capacity liquefaction of natural gas

Science.gov (United States)

Chang, Ho-Myung; Park, Jae Hoon; Gwak, Kyung Hyun; Choe, Kun Hyung

2014-01-01

Thermodynamic study is performed on nitrogen expander cycles for large capacity liquefaction of natural gas. In order to substantially increase the capacity, a Brayton refrigeration cycle with nitrogen expander was recently added to the cold end of the reputable propane pre-cooled mixed-refrigerant (C3-MR) process. Similar modifications with a nitrogen expander cycle are extensively investigated on a variety of cycle configurations. The existing and modified cycles are simulated with commercial process software (Aspen HYSYS) based on selected specifications. The results are compared in terms of thermodynamic efficiency, liquefaction capacity, and estimated size of heat exchangers. The combination of C3-MR with partial regeneration and pre-cooling of nitrogen expander cycle is recommended to have a great potential for high efficiency and large capacity.

Nitrogen expander cycles for large capacity liquefaction of natural gas

International Nuclear Information System (INIS)

Chang, Ho-Myung; Park, Jae Hoon; Gwak, Kyung Hyun; Choe, Kun Hyung

2014-01-01

Thermodynamic study is performed on nitrogen expander cycles for large capacity liquefaction of natural gas. In order to substantially increase the capacity, a Brayton refrigeration cycle with nitrogen expander was recently added to the cold end of the reputable propane pre-cooled mixed-refrigerant (C3-MR) process. Similar modifications with a nitrogen expander cycle are extensively investigated on a variety of cycle configurations. The existing and modified cycles are simulated with commercial process software (Aspen HYSYS) based on selected specifications. The results are compared in terms of thermodynamic efficiency, liquefaction capacity, and estimated size of heat exchangers. The combination of C3-MR with partial regeneration and pre-cooling of nitrogen expander cycle is recommended to have a great potential for high efficiency and large capacity

Predicted Liquefaction in the Greater Oakland and Northern Santa Clara Valley Areas for a Repeat of the 1868 Hayward Earthquake

Science.gov (United States)

Holzer, T. L.; Noce, T. E.; Bennett, M. J.

2008-12-01

Probabilities of surface manifestations of liquefaction due to a repeat of the 1868 (M6.7-7.0) earthquake on the southern segment of the Hayward Fault were calculated for two areas along the margin of San Francisco Bay, California: greater Oakland and the northern Santa Clara Valley. Liquefaction is predicted to be more common in the greater Oakland area than in the northern Santa Clara Valley owing to the presence of 57 km2 of susceptible sandy artificial fill. Most of the fills were placed into San Francisco Bay during the first half of the 20th century to build military bases, port facilities, and shoreline communities like Alameda and Bay Farm Island. Probabilities of liquefaction in the area underlain by this sandy artificial fill range from 0.2 to ~0.5 for a M7.0 earthquake, and decrease to 0.1 to ~0.4 for a M6.7 earthquake. In the greater Oakland area, liquefaction probabilities generally are less than 0.05 for Holocene alluvial fan deposits, which underlie most of the remaining flat-lying urban area. In the northern Santa Clara Valley for a M7.0 earthquake on the Hayward Fault and an assumed water-table depth of 1.5 m (the historically shallowest water level), liquefaction probabilities range from 0.1 to 0.2 along Coyote and Guadalupe Creeks, but are less than 0.05 elsewhere. For a M6.7 earthquake, probabilities are greater than 0.1 along Coyote Creek but decrease along Guadalupe Creek to less than 0.1. Areas with high probabilities in the Santa Clara Valley are underlain by latest Holocene alluvial fan levee deposits where liquefaction and lateral spreading occurred during large earthquakes in 1868 and 1906. The liquefaction scenario maps were created with ArcGIS ModelBuilder. Peak ground accelerations first were computed with the new Boore and Atkinson NGA attenuation relation (2008, Earthquake Spectra, 24:1, p. 99-138), using VS30 to account for local site response. Spatial liquefaction probabilities were then estimated using the predicted ground motions

Optimizing the conditions for the microwave-assisted direct liquefaction of Ulva prolifera for bio-oil production using response surface methodology

International Nuclear Information System (INIS)

Liu, Junhai; Zhuang, Yingbin; Li, Yan; Chen, Limei; Guo, Jingxue; Li, Demao; Ye, Naihao

2013-01-01

Microwave-assisted direct liquefaction (MADL) of Ulva prolifera was performed in ethylene glycol (EG) using sulfuric acid (H 2 SO 4 ) as a catalyst. Response Surface Methodology (RSM) based on central composite rotatable design (CCRD) was employed to optimize the conditions of three independent variables (catalyst content, solvent-to-feedstock ratio and temperature) for the liquefaction yield. And the bio-oil was analyzed by elementary analysis, Fourier transform infrared spectroscopic analysis (FT-IR) and gas chromatography–mass spectrometry (GC–MS). The maximum liquefaction yield was 93.17%, which was obtained under a microwave power of 600 W for 30 min at 165 °C with a solvent-to-feedstock ratio of 18.87:1 and 4.93% sulfuric acid. The bio-oil was mainly composed of phthalic acid esters, alkenes and a fatty acid methyl ester with a long chain from C 16 to C 20 . - Highlights: • Ulva prolifera was converted to bio-oil through microwave-assisted direct liquefaction. • Response surface methodology was used to optimize the liquefaction technology. • A maximum liquefaction rate of 93.17 wt% bio-oil was obtained. • The bio-oil was composed of carboxylic acids and esters

Influence of ethylene glycol pretreatment on effectiveness of atmospheric pressure plasma treatment of polyethylene fibers

International Nuclear Information System (INIS)

Wen Ying; Li Ranxing; Cai Fang; Fu Kun; Peng Shujing; Jiang Qiuran; Yao Lan; Qiu Yiping

2010-01-01

For atmospheric pressure plasma treatments, the results of plasma treatments may be influenced by liquids adsorbed into the substrate. This paper studies the influence of ethylene glycol (EG) pretreatment on the effectiveness of atmospheric plasma jet (APPJ) treatment of ultrahigh molecular weight polyethylene (UHMWPE) fibers with 0.31% and 0.42% weight gain after soaked in EG/water solution with concentration of 0.15 and 0.3 mol/l for 24 h, respectively. Scanning electron microscopy (SEM) shows that the surface of fibers pretreated with EG/water solution does not have observable difference from that of the control group. The X-ray photoelectron spectroscopy (XPS) results show that the oxygen concentration on the surface of EG-pretreated fibers is increased less than the plasma directly treated fibers. The interfacial shear strength (IFSS) of plasma directly treated fibers to epoxy is increased almost 3 times compared with the control group while that of EG-pretreated fibers to epoxy does not change except for the fibers pretreated with lower EG concentration and longer plasma treatment time. EG pretreatment reduces the water contact angle of UHMWPE fibers. In conclusion, EG pretreatment can hamper the effect of plasma treatment of UHMWPE fibers and therefore longer plasma treatment duration is required for fibers pretreated with EG.

Effect of Pretreatments on Seed Viability During Fruit Development ...

African Journals Online (AJOL)

Fiifi Baidoo

and petri dishes on moist filter paper, gave 80% germination in variety gabonensis, 20 weeks after fruiting. .... Effect of pretreatments on seed germination of fruits of Irvingia gabonensis plucked from forest ...... A review of the tariff structure and.

Isolation and characterization of cellulose nanofibers from bamboo using microwave liquefaction combined with chemical treatment and ultrasonication

Science.gov (United States)

Jiulong Xie; Chung Hse; Cornelis F. De Hoop; Tingxing Hu; Jinqiu Qi; Todd F. Shupe

2016-01-01

Cellulose nanofibers were successfully isolated from bamboo using microwave liquefaction combinedwith chemical treatment and ultrasonic nanofibrillation processes. The microwave liquefaction couldeliminate almost all the lignin in bamboo, resulting in high cellulose content residues within 7 min, andthe cellulose enriched residues could be readily purified by...

Effect of thermal, chemical and thermo-chemical pre-treatments to enhance methane production

Energy Technology Data Exchange (ETDEWEB)

Rafique, Rashad; Nizami, Abdul-Sattar; Murphy, Jerry D.; Kiely, Gerard [Department of Civil and Environmental Engineering, University College Cork (Ireland); Poulsen, Tjalfe Gorm [Department of Biotechnology, Chemistry and Environmental Engineering, Aalborg University (Denmark); Asam, Zaki-ul-Zaman [Department of Civil Engineering, National University of Ireland Galway (Ireland)

2010-12-15

The rise in oil price triggered the exploration and enhancement of various renewable energy sources. Producing biogas from organic waste is not only providing a clean sustainable indigenous fuel to the number of on-farm digesters in Europe, but also reducing the ecological and environmental deterioration. The lignocellulosic substrates are not completely biodegraded in anaerobic digesters operating at commercial scale due to their complex physical and chemical structure, which result in meager energy recovery in terms of methane yield. The focus of this study is to investigate the effect of pre-treatments: thermal, thermo-chemical and chemical pre-treatments on the biogas and methane potential of dewatered pig manure. A laboratory scale batch digester is used for these pre-treatments at different temperature range (25 C-150 C). Results showed that thermo-chemical pretreatment has high effect on biogas and methane potential in the temperature range (25-100 C). Maximum enhancement is observed at 70 C with increase of 78% biogas and 60% methane production. Thermal pretreatment also showed enhancement in the temperature range (50-10 C), with maximum enhancement at 100 C having 28% biogas and 25% methane increase. (author)

Effect of heat treatment changes on swelling treatment of coal; Sekitan no bojun shori sayo ni oyobosu netsushori henka no eikyo

Energy Technology Data Exchange (ETDEWEB)

Satsuka, T.; Mashimo, K.; Wainai, T. [Nihon University, Tokyo (Japan). College of Science and Technology

1996-10-28

Discussions were given on effects of heat treatment at relatively low temperatures as a pretreatment for coal liquefaction on coal swelling and hydrogenolysis reaction. Taiheiyo coal was heated to 200{degree}C for one hour as a pretreatment. The attempted heating methods consisted of four steps of rapid heating (6.7{degree}C/min)quenching (20{degree}C/min), rapid heating/natural cooling (0.7{degree}C/min), heating (1.0{degree}C/min)/quenching, and heating/natural cooling. The swelling treatment was composed of adding methanol benzene into heat treated coal, and leaving it at room temperature for 24 hours. The hydrogenolysis was carried out by using a tetralin solvent and at an initial hydrogen pressure of 20 kg/cm{sup 2} and a temperature of 350{degree}C and for a time of one hour. Hydrogenolysis conversion in the heat treated coal was found lower than that of the original coal because of generation of liquefaction inactive components due to thermal polymerization. When the heat treated coal is swollen by using the solvent, gas yield from the hydrogenolysis reaction decreased due to gas suppression effect, and the conversion was lower than that of the original coal. Heat treatment suggests densification of the coal structure. Swollen coal shows no conspicuous difference in the heat treatment methods against the hydrogenolysis due to the swelling effect. 3 refs., 5 figs., 1 tab.

Fiscal 1989 report on the bituminous coal liquefaction section meeting; 1989 nendo rekiseitan ekika bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1990-03-01

At the 1st, 2nd, and 3rd group meetings held for the fiscal year, reports are given and discussions are made about the progress of research and development. Reported and discussed in relation to the progress of the pilot plant support research are studies with the 1t/d PSU (process supporting unit) (Nippon Steel Corporation, Mitsui Coal Liquefaction Co., Ltd., and Japan Coal Oil Co., Ltd.); improvement on distillate distribution (Sumitomo Metal Industries, Ltd.); development of an optimum decalcification technique (Sumitomo Coal Mining Co., Ltd., and Sumitomo Metal Industries, Ltd.); studies of solvent hydrogenation catalysts (Sumitomo Metal Mining Co., Ltd., and Chiyoda Corp.); and studies of coal liquefaction conditions (Mitsui Engineering and Shipbuilding Co., Ltd.). In relation to studies using a bituminous coal liquefaction pilot plant, the progress of the 150t/d PP (pilot plant) effort (Japan Coal Oil, Co., Ltd.) and the outlines of pilot surveys (Japan Coal Oil Co., Ltd.) are reported and discussed, the latter covering liquefaction solvent performance optimization, slurry preheating furnaces, coal slurry properties, and so forth. (NEDO)

Ground Characterization Studies in Canakkale Pilot Site of LIQUEFACT Project

Science.gov (United States)

Ozcep, F.; Oztoprak, S.; Aysal, N.; Bozbey, I.; Tezel, O.; Ozer, C.; Sargin, S.; Bekin, E.; Almasraf, M.; Cengiz Cinku, M.; Ozdemir, K.

2017-12-01

The our aim is to outline the ground characterisation studies in Canakkale test site. Study is based on the EU H2020 LIQUEFACT project entitled "Liquefact: Assessment and mitigation of liquefaction potential across Europe: a holistic approach to protect structures / infrastructures for improved resilience to earthquake-induced liquefaction disasters". Objectives and extent of ground characterization for Canakkale test site includes pre-existing soil investigation studies and complementary field studies. There were several SPT and geophysical tests carried out in the study area. Within the context of the complementary tests, six (6) study areas in the test site were chosen and complementary tests were carried out in these areas. In these areas, additional boreholes were opened and SPT tests were performed. It was decided that additional CPT (CPTU and SCPT) and Marchetti Dilatometer (DMT) tests should be carried out within the scope of the complementary testing. Seismic refraction, MASW and micro tremor measurements had been carried out in pre-existing studies. Shear wave velocities obtained from MASW measurements were evaluated to the most rigorous level. These tests were downhole seismic, PS-logging, seismic refraction, 2D-ReMi, MASW, micro tremor (H/V Nakamura method), 2D resistivity and resonance acoustic profiling (RAP). RAP is a new technique which will be explained briefly in the relevant section. Dynamic soil properties had not been measured in pre-existing studies, therefore these properties were investigated within the scope of the complementary tests. Selection of specific experimental tests of the complementary campaign was based on cost-benefit considerations Within the context of complementary field studies, dynamic soil properties were measured using resonant column and cyclic direct shear tests. Several sieve analyses and Atterberg Limits tests which were documented in the pre-existing studies were evaluated. In the complementary study carried out

Effect of cadmium pretreatment on liver regeneration after partial hepatectomy in rats

International Nuclear Information System (INIS)

Margeli, A.; Theocharis, S.; Skaltsas, S.; Skopelitou, A.; Kittas, C.; Mykoniatis, M.; Varonos, D.

1994-01-01

In this study we examined the effect of cadmium pretreatment, administered 24 h before partial hepatectomy, on the liver regenerative process in rats, at different time intervals. The rate of 3 H thymidine incorporation into hepatic DNA and the activity of the enzyme thymidine kinase were used as indices of liver proliferative capacity. Thymidine kinase, the rate-determining enzyme of DNA biosynthesis, was suppressed during the first hours following partial hepatectomy in the liver of cadmium pretreated animals. DNA biosynthesis was also strongly decreased in cadmium pretreated animals, by delaying the first peak of liver regeneration, compared with the partially hepatectomized ones. Biochemical parameters, mitotic index and proliferating cell nuclear antigen staining were also coestimated. The above data suggest that cadmium pretreatment suppressed the hepatic regenerative process, probably due to the inhibition of thymidine kinase. (orig./MG)

The making of Andersen’s liquefaction chart

OpenAIRE

Sabaliauskas, Tomas; Ibsen, Lars Bo

2017-01-01

Andersen’s chart (Andersen & Berre, 1999) is a graphical method of observing cyclic soil response. It allows observing soil response to various stress amplitudes that can lead to liquefaction, excess plastic deformation stabilizing soil response.The process of obtaining the original chart has been improved. Algorithm based approximation is introduced. Pore pressure dependent ultimate bearing capacity normalization factor is introduced to normalize the chart.

The effect of microwave pretreatment on chemical looping gasification of microalgae for syngas production

International Nuclear Information System (INIS)

Hu, Zhifeng; Ma, Xiaoqian; Jiang, Enchen

2017-01-01

Highlights: • Microwave pretreatment is beneficial to chemical-looping gasification reaction. • Gasification efficiency and gas yield increased greatly under microwave pretreatment. • 60 s is the optimal microwave pretreatment time in CLG to produce syngas. • Suitable microwave pretreatment can make the structure of solid residue become loose. • 750 W is the optimal microwave pretreatment power in CLG to produce syngas. - Abstract: Chemical-looping gasification (CLG) of Chlorella vulgaris was carried out in a quartz tube reactor under different microwave pretreatment. The product fractional yields, conversion efficiency and analysis of performance parameters were analyzed in order to obtain the characterization and optimal conditions of microwave pretreatment for syngas production. The results indicate that microwave pretreatment is conducive to CLG reaction. Furthermore, the higher power or the longer time in the process of microwave pretreatment could not exhibit a better effect on CLG. In addition, 750 W and 60 s is the optimal microwave pretreatment power and time respectively to obtain a great reducibility of oxygen carrier, high conversion efficiency, high products yield and good LHV. The H_2 yield, LHV, gasification efficiency and gas yield increased obviously from 18.12%, 12.14 MJ/Nm"3, 59.76% and 1.04 Nm"3/kg of untreated Chlorella vulgaris to 24.55%, 13.13 MJ/Nm"3, 72.16% and 1.16 Nm"3/kg of the optimal microwave pretreatment condition, respectively.

Fractional Multistage Hydrothermal Liquefaction of Biomass and Catalytic Conversion into Hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Cortright, Randy [Virent, Inc., Madison, WI (United States); Rozmiarek, Robert [Virent, Inc., Madison, WI (United States); Dally, Brice [Virent, Inc., Madison, WI (United States); Holland, Chris [Virent, Inc., Madison, WI (United States)

2017-08-31

The objective of this project was to develop an improved multistage process for the hydrothermal liquefaction (HTL) of biomass to serve as a new front-end, deconstruction process ideally suited to feed Virent’s well-proven catalytic technology, which is already being scaled up. This process produced water soluble, partially de-oxygenated intermediates that are ideally suited for catalytic finishing to fungible distillate hydrocarbons. Through this project, Virent, with its partners, demonstrated the conversion of pine wood chips to drop-in hydrocarbon distillate fuels using a multi-stage fractional conversion system that is integrated with Virent’s BioForming® process. The majority of work was in the liquefaction task and included temperature scoping, solvent optimization, and separations.

Method for controlling boiling point distribution of coal liquefaction oil product

Science.gov (United States)

Anderson, Raymond P.; Schmalzer, David K.; Wright, Charles H.

1982-12-21

The relative ratio of heavy distillate to light distillate produced in a coal liquefaction process is continuously controlled by automatically and continuously controlling the ratio of heavy distillate to light distillate in a liquid solvent used to form the feed slurry to the coal liquefaction zone, and varying the weight ratio of heavy distillate to light distillate in the liquid solvent inversely with respect to the desired weight ratio of heavy distillate to light distillate in the distillate fuel oil product. The concentration of light distillate and heavy distillate in the liquid solvent is controlled by recycling predetermined amounts of light distillate and heavy distillate for admixture with feed coal to the process in accordance with the foregoing relationships.

Lignocellulosic Biomass Pretreatment Using AFEX

Science.gov (United States)

Balan, Venkatesh; Bals, Bryan; Chundawat, Shishir P. S.; Marshall, Derek; Dale, Bruce E.

Although cellulose is the most abundant organic molecule, its susceptibility to hydrolysis is restricted due to the rigid lignin and hemicellulose protection surrounding the cellulose micro fibrils. Therefore, an effective pretreatment is necessary to liberate the cellulose from the lignin-hemicellulose seal and also reduce cellulosic crystallinity. Some of the available pretreatment techniques include acid hydrolysis, steam explosion, ammonia fiber expansion (AFEX), alkaline wet oxidation, and hot water pretreatment. Besides reducing lignocellulosic recalcitrance, an ideal pretreatment must also minimize formation of degradation products that inhibit subsequent hydrolysis and fermentation. AFEX is an important pretreatment technology that utilizes both physical (high temperature and pressure) and chemical (ammonia) processes to achieve effective pretreatment. Besides increasing the surface accessibility for hydrolysis, AFEX promotes cellulose decrystallization and partial hemicellulose depolymerization and reduces the lignin recalcitrance in the treated biomass. Theoretical glucose yield upon optimal enzymatic hydrolysis on AFEX-treated corn stover is approximately 98%. Furthermore, AFEX offers several unique advantages over other pretreatments, which include near complete recovery of the pretreatment chemical (ammonia), nutrient addition for microbial growth through the remaining ammonia on pretreated biomass, and not requiring a washing step during the process which facilitates high solid loading hydrolysis. This chapter provides a detailed practical procedure to perform AFEX, design the reactor, determine the mass balances, and conduct the process safely.

BP and NCB to collaborate in coal liquefaction study. [Supercritical gas extraction; dissolution in anthracene oil

Energy Technology Data Exchange (ETDEWEB)

1978-02-17

British Petroleum and NCB are collaborating in a two year study of coal liquefaction which could result in a demonstration plant being built. The two liquefaction techniques which the NCB is developing at present are supercritical extraction, and dissolution in anthracene oil. A disadvantage of the latter process is that high grade coking coals must be used.

Thermodynamic design of natural gas liquefaction cycles for offshore application

Science.gov (United States)

Chang, Ho-Myung; Lim, Hye Su; Choe, Kun Hyung

2014-09-01

A thermodynamic study is carried out for natural gas liquefaction cycles applicable to offshore floating plants, as partial efforts of an ongoing governmental project in Korea. For offshore liquefaction, the most suitable cycle may be different from the on-land LNG processes under operation, because compactness and simple operation are important as well as thermodynamic efficiency. As a turbine-based cycle, closed Claude cycle is proposed to use NG (natural gas) itself as refrigerant. The optimal condition for NG Claude cycle is determined with a process simulator (Aspen HYSYS), and the results are compared with fully-developed C3-MR (propane pre-cooled mixed refrigerant) JT cycles and various N2 (nitrogen) Brayton cycles in terms of efficiency and compactness. The newly proposed NG Claude cycle could be a good candidate for offshore LNG processes.

Re-Condensation and Liquefaction of Helium and Hydrogen Using Coolers

International Nuclear Information System (INIS)

Green, Michael A.

2009-01-01

Coolers are used to cool cryogen free devices at temperatures from 5 to 30 K. Cryogen free cooling involves a temperature drop within the device being cooled and between the device and the cooler cold heads. Liquid cooling with a liquid cryogen distributed over the surface of a device combined with re-condensation can result in a much lower temperature drop between the cooler and the device being cooled. The next logical step beyond simple re-condensation is using a cooler to liquefy the liquid cryogen in the device. A number of tests of helium liquefaction and re-condensation of helium have been run using a pulse tube cooler in the drop-in mode. This report discusses the parameter space over which re-condensation and liquefaction for helium and hydrogen can occur.

Ethanol production from industrial hemp: effect of combined dilute acid/steam pretreatment and economic aspects

DEFF Research Database (Denmark)

Gunnarsson, Ingólfur Bragi; Svensson, Sven-Erik; Prade, Thomas

2014-01-01

In the present study, combined steam (140-180 °C) and dilute-acid pre-hydrolysis (0.0-2.0%) were applied to industrial hemp (Cannabis sativa L.), as pretreatment for lignocellulosic bioethanol production. The influence of the pretreatment conditions and cultivation type on the hydrolysis and etha......In the present study, combined steam (140-180 °C) and dilute-acid pre-hydrolysis (0.0-2.0%) were applied to industrial hemp (Cannabis sativa L.), as pretreatment for lignocellulosic bioethanol production. The influence of the pretreatment conditions and cultivation type on the hydrolysis...... pretreated at the optimal conditions showed positive economic results. The type of hemp cultivation (organic or conventional) did not influence significantly the effectiveness of the pretreatment and subsequent enzymatic hydrolysis and ethanol fermentation....

Bonding effectiveness to different chemically pre-treated dental zirconia.

Science.gov (United States)

Inokoshi, Masanao; Poitevin, André; De Munck, Jan; Minakuchi, Shunsuke; Van Meerbeek, Bart

2014-09-01

The objective of this study was to evaluate the effect of different chemical pre-treatments on the bond durability to dental zirconia. Fully sintered IPS e.max ZirCAD (Ivoclar Vivadent) blocks were subjected to tribochemical silica sandblasting (CoJet, 3M ESPE). The zirconia samples were additionally pre-treated using one of four zirconia primers/adhesives (Clearfil Ceramic Primer, Kuraray Noritake; Monobond Plus, Ivoclar Vivadent; Scotchbond Universal, 3M ESPE; Z-PRIME Plus, Bisco). Finally, two identically pre-treated zirconia blocks were bonded together using composite cement (RelyX Ultimate, 3M ESPE). The specimens were trimmed at the interface to a cylindrical hourglass and stored in distilled water (7 days, 37 °C), after which they were randomly tested as is or subjected to mechanical ageing involving cyclic tensile stress (10 N, 10 Hz, 10,000 cycles). Subsequently, the micro-tensile bond strength was determined, and SEM fractographic analysis performed. Weibull analysis revealed the highest Weibull scale and shape parameters for the 'Clearfil Ceramic Primer/mechanical ageing' combination. Chemical pre-treatment of CoJet (3M ESPE) sandblasted zirconia using Clearfil Ceramic Primer (Kuraray Noritake) and Monobond Plus (Ivoclar Vivadent) revealed a significantly higher bond strength than when Scotchbond Universal (3M ESPE) and Z-PRIME Plus (Bisco) were used. After ageing, Clearfil Ceramic Primer (Kuraray Noritake) revealed the most stable bond durability. Combined mechanical/chemical pre-treatment, the latter with either Clearfil Ceramic Primer (Kuraray Noritake) or Monobond Plus (Ivoclar Vivadent), resulted in the most durable bond to zirconia. As a standard procedure to durably bond zirconia to tooth tissue, the application of a combined 10-methacryloyloxydecyl dihydrogen phosphate/silane ceramic primer to zirconia is clinically highly recommended.

Effect of operating conditions on direct liquefaction of low-lipid microalgae in ethanol-water co-solvent for bio-oil production

International Nuclear Information System (INIS)

Ji, Changhao; He, Zhixia; Wang, Qian; Xu, Guisheng; Wang, Shuang; Xu, Zhixiang; Ji, Hengsong

2017-01-01

Highlights: • Low-lipid microalgae was selected as feedstock for DL in ethanol-water co-solvent. • Operating conditions had great influence on product yields and conversion rate. • Bio-oil could be obtained from all three main components. • Ethanol and water showed obviously synergistic effect during the DL of microalgae. • Bio-oil composition from DL of microalgae was different from lignocellulose biomass. - Abstract: In this work, the direct liquefaction (DL) of low-lipid microalgae Spirulina was investigated in a 50 ml autoclave reactor with ethanol and water as co-solvent. The objective of this research was carried out to examine the effect of operating conditions such as reaction temperature, reaction time, solvent/microalgae (S/M) ratio and ethanol-water co-solvent (EWCS) composition on product distribution and bio-oil characterization. The results revealed that the optimal operating conditions for bio-oil yield and conversion rate were reaction temperature of 300 °C, reaction time of 45 min, ethanol content of 50 vol.% and S/M ratio of 40/4 ml/g, which gave the bio-oil yield of 59.5% and conversion rate of 94.73%. Conversion rate in EWCS was significantly higher than that in pure water or ethanol, suggesting the synergistic effect between ethanol and water during microalgae DL. Distinct difference in composition and relative content of compound among bio-oils in different solvents were observed by GC–MS and FT-IR. Compared with hydrothermal liquefaction, the most abundant compounds in bio-oil from both EWCS and pure ethanol were esters. The presence of ethanol could enhance the bio-oil yield and improve bio-oil quality by promoting the formation of esters.

Sensitizing Effects of Pretreatment Measures on Cancer Chemotherapy Nausea and Vomiting.

Science.gov (United States)

Gard, Diane; And Others

1988-01-01

Explored sensitizing effects of pretreatment assessment on posttreatment chemotherapy nausea and vomiting and interactive effects of personal dispositions for information seeking. Oncology patients rated side effects experienced previously (experimental condition), or parking conditions (control). Posttreatment, nausea of experimentals was…

Earthquake induced liquefaction hazard, probability and risk assessment in the city of Kolkata, India: its historical perspective and deterministic scenario

Science.gov (United States)

Nath, Sankar Kumar; Srivastava, Nishtha; Ghatak, Chitralekha; Adhikari, Manik Das; Ghosh, Ambarish; Sinha Ray, S. P.

2018-01-01

Liquefaction-induced ground failure is one amongst the leading causes of infrastructure damage due to the impact of large earthquakes in unconsolidated, non-cohesive, water saturated alluvial terrains. The city of Kolkata is located on the potentially liquefiable alluvial fan deposits of Ganga-Bramhaputra-Meghna Delta system with subsurface litho-stratigraphic sequence comprising of varying percentages of clay, cohesionless silt, sand, and gravel interbedded with decomposed wood and peat. Additionally, the region has moderately shallow groundwater condition especially in the post-monsoon seasons. In view of burgeoning population, there had been unplanned expansion of settlements in the hazardous geological, geomorphological, and hydrological conditions exposing the city to severe liquefaction hazard. The 1897 Shillong and 1934 Bihar-Nepal earthquakes both of M w 8.1 reportedly induced Modified Mercalli Intensity of IV-V and VI-VII respectively in the city reportedly triggering widespread to sporadic liquefaction condition with surface manifestation of sand boils, lateral spreading, ground subsidence, etc., thus posing a strong case for liquefaction potential analysis in the terrain. With the motivation of assessing seismic hazard, vulnerability, and risk of the city of Kolkata through a consorted federal funding stipulated for all the metros and upstart urban centers in India located in BIS seismic zones III, IV, and V with population more than one million, an attempt has been made here to understand the liquefaction susceptibility condition of Kolkata under the impact of earthquake loading employing modern multivariate techniques and also to predict deterministic liquefaction scenario of the city in the event of a probabilistic seismic hazard condition with 10% probability of exceedance in 50 years and a return period of 475 years. We conducted in-depth geophysical and geotechnical investigations in the city encompassing 435 km2 area. The stochastically

SU-E-T-148: Benchmarks and Pre-Treatment Reviews: A Study of Quality Assurance Effectiveness

International Nuclear Information System (INIS)

Lowenstein, J; Nguyen, H; Roll, J; Walsh, A; Tailor, A; Followill, D

2015-01-01

Purpose: To determine the impact benchmarks and pre-treatment reviews have on improving the quality of submitted clinical trial data. Methods: Benchmarks are used to evaluate a site’s ability to develop a treatment that meets a specific protocol’s treatment guidelines prior to placing their first patient on the protocol. A pre-treatment review is an actual patient placed on the protocol in which the dosimetry and contour volumes are evaluated to be per protocol guidelines prior to allowing the beginning of the treatment. A key component of these QA mechanisms is that sites are provided timely feedback to educate them on how to plan per the protocol and prevent protocol deviations on patients accrued to a protocol. For both benchmarks and pre-treatment reviews a dose volume analysis (DVA) was performed using MIM softwareTM. For pre-treatment reviews a volume contour evaluation was also performed. Results: IROC Houston performed a QA effectiveness analysis of a protocol which required both benchmarks and pre-treatment reviews. In 70 percent of the patient cases submitted, the benchmark played an effective role in assuring that the pre-treatment review of the cases met protocol requirements. The 35 percent of sites failing the benchmark subsequently modified there planning technique to pass the benchmark before being allowed to submit a patient for pre-treatment review. However, in 30 percent of the submitted cases the pre-treatment review failed where the majority (71 percent) failed the DVA. 20 percent of sites submitting patients failed to correct their dose volume discrepancies indicated by the benchmark case. Conclusion: Benchmark cases and pre-treatment reviews can be an effective QA tool to educate sites on protocol guidelines and to minimize deviations. Without the benchmark cases it is possible that 65 percent of the cases undergoing a pre-treatment review would have failed to meet the protocols requirements.Support: U24-CA-180803

Report for fiscal 1981 of Sunshine Program coal group. Basic research on Solvolysis liquefaction technology; 1981 nendo solvolysis ekika gijutsu no kiso kenkyu hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-03-01

Basic research is conducted on the Solvolysis liquefaction process for the purpose of producing from coal an ashless, low-sulfur, pollution-free liquid fuel. In the research on the Solvolysis liquefaction (1st stage liquefaction) of coal using a hydrogenation solvent, the Solvolysis liquefaction of coal is studied, for which a refined Solvolysis pitch containing coal substances and a hydride of solvent refined coal are used as Solvolysis liquefaction solvents for the 1st stage. In the research on the 1st stage liquefaction reaction conditions using a high-temperature closed process, two methods are employed. One is a method that uses a mini-pump type reactor in which a small hermetic container is submerged in a high-temperature solvent for rapid heating and the other is a method that uses a pipe type reactor in which coal slurry is caused to travel through a pipe heated to a high temperature. For the analysis of the 2nd stage liquefaction (hydrogenation) reaction conditions, the properties of the 2nd coal liquid, and the constitution of the 2nd coal liquid, and the for the research on the 1st stage liquefaction capacity, the hydrogenation of anthracene oil and solvent refined coal as recyclable solvent models is studied. (NEDO)

Process and analytical studies of enhanced low severity co-processing using selective coal pretreatment. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Baldwin, R.M.; Miller, R.L.

1991-12-01

The findings in the first phase were as follows: 1. Both reductive (non-selective) alkylation and selective oxygen alkylation brought about an increase in liquefaction reactivity for both coals. 2. Selective oxygen alkylation is more effective in enhancing the reactivity of low rank coals. In the second phase of studies, the major findings were as follows: 1. Liquefaction reactivity increases with increasing level of alkylation for both hydroliquefaction and co-processing reaction conditions. 2. the increase in reactivity found for O-alkylated Wyodak subbituminous coal is caused by chemical changes at phenolic and carboxylic functional sites. 3. O-methylation of Wyodak subbituminous coal reduced the apparent activation energy for liquefaction of this coal.

Effect of Kaempferol Pretreatment on Myocardial Injury in Rats.

Science.gov (United States)

Vishwakarma, Anamika; Singh, Thakur Uttam; Rungsung, Soya; Kumar, Tarun; Kandasamy, Arunvikram; Parida, Subhashree; Lingaraju, Madhu Cholenahalli; Kumar, Ajay; Kumar, Asok; Kumar, Dinesh

2018-01-20

The present study was undertaken to evaluate the effect of kaempferol in isoprenaline (ISP)-induced myocardial injury in rats. ISP was administered subcutaneously for two subsequent days to induce myocardial injury. Assessment of myocardial injury was done by estimation of hemodynamic functions, myocardial infarcted area, cardiac injury markers, lipid profile, oxidative stress, pro-inflammatory cytokines and histopathology of heart and liver. Rats pretreated with kaempferol showed reduction in the myocardial infarcted area and heart rate. However, no improvement was observed in change in body weight, mean arterial, systolic and diastolic blood pressure. Kaempferol showed significant decrease in serum LDH, CK-MB, troponin-I and lipid profile. However, highest dose of kaempferol did not reduce the serum triglyceride level. Further, antioxidant enzymes, SOD and catalase, were also higher. However, reduced glutathione, serum SGOT and creatinine did not show any improvement. Kaempferol showed reduction in MDA level. Kaempferol at highest dose showed reduction in pro-MMP-2 expression and MMP-9 level. mRNA expression level of TNF-α was not different in kaempferol-pretreated myocardial injured rats with ISP-alone group. Pretreatment with kaempferol at highest dose showed mild mononuclear infiltration and degenerative changes in heart tissue section of myocardial injured rats. Rats pretreated with kaempferol at higher concentration showed normal cordlike arrangement of hepatocytes with moderate swelling of hepatocytes (vacuolar degeneration) around the central vein. Study suggests that kaempferol attenuated lipid profile, infarcted area and oxidative stress in ISP-induced myocardial injury in rats.

Liquefaction-induced lateral spreading in Oceano, California, during the 2003 San Simeon Earthquake

Science.gov (United States)

Holzer, Thomas L.; Noce, Thomas E.; Bennett, Michael J.; Di Alessandro, Carola; Boatwright, John; Tinsley, John C.; Sell, Russell W.; Rosenberg, Lewis I.

2004-01-01

The December 22, 2003, San Simeon, California, (M6.5) earthquake caused damage to houses, road surfaces, and underground utilities in Oceano, California. The community of Oceano is approximately 50 miles (80 km) from the earthquake epicenter. Damage at this distance from a M6.5 earthquake is unusual. To understand the causes of this damage, the U.S. Geological Survey conducted extensive subsurface exploration and monitoring of aftershocks in the months after the earthquake. The investigation included 37 seismic cone penetration tests, 5 soil borings, and aftershock monitoring from January 28 to March 7, 2004. The USGS investigation identified two earthquake hazards in Oceano that explain the San Simeon earthquake damage?site amplification and liquefaction. Site amplification is a phenomenon observed in many earthquakes where the strength of the shaking increases abnormally in areas where the seismic-wave velocity of shallow geologic layers is low. As a result, earthquake shaking is felt more strongly than in surrounding areas without similar geologic conditions. Site amplification in Oceano is indicated by the physical properties of the geologic layers beneath Oceano and was confirmed by monitoring aftershocks. Liquefaction, which is also commonly observed during earthquakes, is a phenomenon where saturated sands lose their strength during an earthquake and become fluid-like and mobile. As a result, the ground may undergo large permanent displacements that can damage underground utilities and well-built surface structures. The type of displacement of major concern associated with liquefaction is lateral spreading because it involves displacement of large blocks of ground down gentle slopes or towards stream channels. The USGS investigation indicates that the shallow geologic units beneath Oceano are very susceptible to liquefaction. They include young sand dunes and clean sandy artificial fill that was used to bury and convert marshes into developable lots. Most of

Effects of thermo-chemical pre-treatment on anaerobic biodegradability and hydrolysis of lignocellulosic biomass

NARCIS (Netherlands)

Fernandes, T.; Klaasse Bos, G.J.; Zeeman, G.; Sanders, J.P.M.; Lier, van J.B.

2009-01-01

The effects of different thermo-chemical pre-treatment methods were determined on the biodegradability and hydrolysis rate of lignocellulosic biomass. Three plant species, hay, straw and bracken were thermo-chemically pre-treated with calcium hydroxide, ammonium carbonate and maleic acid. After

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Summary of FY 1980 results of Sunshine Project. Development of coal liquefaction techniques; 1980 nendo sekitan ekika gijutsu no kaihatsu seika hokokusho. Sunshine keikaku itaku kenkyu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

1981-03-01

This report summarizes the results of the 3 R and D themes for coal liquefaction techniques, pursued by the Sunshine Project; (1) development of solvent extraction type liquefaction plant, and brown coal liquefaction technique R and D demonstration surveys, (2) development of solvolysis type liquefaction plant, and (3) development of direct hydrogenation type liquefaction plant. For the theme (1), the 1 T/D test plant, solid/liquid separator and small-size continuous settlement separator are constructed, and partly completed. The elementary studies include solvent extraction type liquefaction process, materials for coal liquefaction plant and solid/liquid separation. Australia's Victoria brown coal and Chinese coal are studied to clarify the possible problems involved in liquefaction of these coal species for commercialization of the liquefaction techniques in the early stage. The elementary techniques studied include dehydration of brown coal, milling at high temperature in oil, de-ashing, and secondary and primary hydrogenation. For the theme (2), the 1 T/D plant is inspected and maintained to clarify the problems involved in the continuous operation, revamped and repaired as necessary, given preventive maintenance, and tested for operability confirmation. The elementary studies include solvolysis type liquefaction process, scale-up, hydrogenation plant for solvolysis pitch. For the item (3), the 2.4 T/D test plant is constructed, and the elementary studies are conducted, for, e.g., liquefaction reactions in the presence of an iron-based catalyst. (NEDO)

Thermodynamic design of hydrogen liquefaction systems with helium or neon Brayton refrigerator

Science.gov (United States)

Chang, Ho-Myung; Ryu, Ki Nam; Baik, Jong Hoon

2018-04-01

A thermodynamic study is carried out for the design of hydrogen liquefaction systems with helium (He) or neon (Ne) Brayton refrigerator. This effort is motivated by our immediate goal to develop a small-capacity (100 L/h) liquefier for domestic use in Korea. Eight different cycles are proposed and their thermodynamic performance is investigated in comparison with the existing liquefaction systems. The proposed cycles include the standard and modified versions of He Brayton refrigerators whose lowest temperature is below 20 K. The Brayton refrigerator is in direct thermal contact with the hydrogen flow at atmospheric pressure from ambient-temperature gas to cryogenic liquid. The Linde-Hampson system pre-cooled by a Ne Brayton refrigerator is also considered. Full cycle analysis is performed with the real properties of fluids to estimate the figure of merit (FOM) under an optimized operation condition. It is concluded that He Brayton refrigerators are feasible for this small-scale liquefaction, because a reasonably high efficiency can be achieved with simple and safe (low-pressure) operation. The complete cycles with He Brayton refrigerator are presented for the development of a prototype, including the ortho-to-para conversion.

Effective enzymatic in situ saccharification of bamboo shoot shell pretreated by dilute alkalic salts sodium hypochlorite/sodium sulfide pretreatment under the autoclave system.

Science.gov (United States)

Chong, Gang-Gang; He, Yu-Cai; Liu, Qiu-Xiang; Kou, Xiao-Qin; Huang, Xiao-Jun; Di, Jun-Hua; Ma, Cui-Luan

2017-10-01

In this study, dilute alkali salts (0.6% NaClO, 0.067% Na 2 S) pretreatment at 10% sulfidity under the autoclave system at 120°C for 40min was used for pretreating bamboo shoot shell (BSS). Furthermore, FT-IR, XRD and SEM were employed to characterize the changes in the cellulose structural characteristics (porosity, morphology, and crystallinity) of the pretreated BSS solid residue. After 72h, the reducing sugars and glucose from the enzymatic in situ hydrolysis of 50g/L pretreated BSS in dilute NaClO/Na 2 S media could be obtained at 31.11 and 20.32g/L, respectively. Finally, the obtained BSS-hydrolysates containing alkalic salt NaClO/Na 2 S resulted in slightly negative effects on the ethanol production. Glucose in BSS-hydrolysates was fermented from 20.0 to 0.17g/L within 48h, and an ethanol yield of 0.41g/g glucose, which represents 80.1% of the theoretical yield, was obtained. This study provided an effective strategy for potential utilization of BSS. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of heat pretreatment temperature on fermentative hydrogen production using mixed cultures

Energy Technology Data Exchange (ETDEWEB)

Baghchehsaraee, Bita; Nakhla, George; Karamanev, Dimitre; Margaritis, Argyrios [Department of Chemical and Biochemical Engineering, The University of Western Ontario, London, Ontario N6A 5B9 (Canada); Reid, Gregor [Department of Microbiology and Immunology, The University of Western Ontario, London, Ontario (Canada); Canadian Research and Development Center for Probiotics, Lawson Health Research Institute, 268 Grosvenor Street, London, Ontario N6A 4V2 (Canada)

2008-08-15

The effect of heat treatment at different temperatures on two types of inocula, activated sludge and anaerobically digested sludge, was investigated in batch cultures. Heat treatments were conducted at 65, 80 and 95 C for 30 min. The untreated inocula produced less amount of hydrogen than the pretreated inocula, with lactic acid as the main metabolite. The maximum yields of 2.3 and 1.6 mol H{sub 2}/mol glucose were achieved for the 65 C pretreated anaerobically digested and activated sludges, respectively. Approximately a 15% decrease in yield was observed with increasing pretreatment temperature from 65 to 95 C concomitant with an increase in butyrate/acetate ratio from 1.5 to 2.4 for anaerobically digested sludge. The increase of pretreatment temperature of activated sludge to 95 C suppressed the hydrogen production by lactic acid fermentation. DNA analysis of the microbial community showed that the elevated pretreatment temperatures reduced the species diversity. (author)

Effect of pretreatments and processing conditions on anti-nutritional factors in climbing bean flours

Directory of Open Access Journals (Sweden)

Emmanuel Mugabo

2017-04-01

Full Text Available It is difficult for many Rwandans to utilize climbing bean seeds (Phaseolus vulgaris. L mainly because of longer cooking time (2 hours and the high consumption of basic fuel. Climbing beans also contain anti-nutritional factors such tannins, phytates, trypsin inhibitors and phytohemagglutinins that limit nutrient absorption. One way to solve this problem is to utilize the flour of climbing beans made from different treatments and processing methods. In this study, climbing beans were pre-treated by soaking them in water for 24 hours, soaking in 2% sodium bicarbonate solution and steam blanching for 10 minutes. After that, pre-treated climbing beans were processed into flours by processing methods such as roasting, cooking and germination where anti-nutritional factors were reduced. The pretreatments did not significantly (p>0.05 affect phytates in climbing bean flours but processing conditions significantly (p<0.05 reduced it. Pretreatments and processing conditions significantly (p<0.05 reduced tannin content. The pretreatments followed by different processing conditions significantly (p<0.05 decreased trypsin inhibitors content. The great significant decrease in phytohemagglutinins content was observed in pretreatment followed by different processing methods. All pretreatments and processing conditions effectively decreased anti-nutritional factors at low level. However, pretreatments or untreated followed by germination and roasting were found to be the most and the least effective respectively.  Making flour from germinated climbing bean seeds is a good option for sustainable food processing as it reduces anti-nutritional factors. It is an inexpensive method in terms of time, energy and fuel for Rwandan households, restaurants and industries where climbing bean seeds are integral part of daily meal.

Application of Freezing and Thawing in Apple (Malus domestica) Juice Extraction.

Science.gov (United States)

Nadulski, Rafał; Kobus, Zbigniew; Wilczyński, Kamil; Zawiślak, Kazimierz; Grochowicz, Józef; Guz, Tomasz

2016-09-28

The paper presents the results of the research on the impact of enzymatic liquefaction, freezing and thawing on the efficiency of juice pressure extraction from apple pulp and quality of the obtained juices. The research was conducted using three types of pretreatment prior the pressing: crushing and enzymatic liquefaction in temperature of 25 °C, crushing and enzymatic liquefaction in temperature of 45 °C and crushing followed by freezing and thawing of the pulp. The study included three varieties of apples. The juice was obtained using a laboratory basket press. It was determined that the pretreatment of the pulp as well as the varietal characteristics of the fruits have a significant impact on the efficiency of the pressure extraction process. The enzymatic treatment of the pulp, irrespective of the temperature at which it was conducted, significantly increased the efficiency of the process. No effect of the temperature (25 or 45 °C) of enzymatic treatment on the efficiency of the pressure extraction process was found. Pretreatment of the pulp based on freezing and thawing contributes to the increase of efficiency of pressing in the case of two apple cultivars, that is, Idared and Red Delicious. It was showed that total phenolic content, antioxidant activity, the soluble solids content and juice acidity (pH) depend on the pretreatment of the pulp and the varietal characteristics of apples. Following the application of pretreatment of the pulp, an increase was observed in the content of polyphenols and in the antioxidant activity of the juices obtained. © 2016 Institute of Food Technologists®

Effects of pretreatment processes on improving the formation of ultrananocrystalline diamond

International Nuclear Information System (INIS)

Chen, Li-Ju; Tai, Nyan-Hwa; Lee, Chi-Young; Lin, I-Nan.

2007-01-01

Effects of pretreatment on the nuclei formation of ultrananocrystalline diamond (UNCD) on Si substrates were studied. Either precoating a thin layer of titanium (∼400 nm) or ultrasonication pretreatment using diamond and titanium mixed powder (D and T process) enhances the nucleation process on Si substrates markedly, and the UNCD nuclei formed and fully covered the Si substrate, when deposition was processed using the microwave-plasma-enhanced chemical-vapor deposition process for 10 min. In contrast, during the same period, ultrasonication pretreatment using diamond powders (D process) can only form large UNCD clusters, which were scarcely distributed on Si substrates. The analyses using x-ray diffractometer, secondary ion mass spectroscopy, and electron spectroscopy for chemical analysis reveal that the titanium layer reacted with carbon species in the plasma, forming crystalline TiC phase, which facilitates the subsequent formation of UNCD nuclei. The beneficial effect of Ti layer on enhancing the nucleation of UNCD is presumably owing to high solubility and high diffusivity of carbon species in Ti materials, as compared with those of Si materials

Continuous bench-scale slurry catalyst testing direct coal liquefaction rawhide sub-bituminous coal

Energy Technology Data Exchange (ETDEWEB)

Bauman, R.F.; Coless, L.A.; Davis, S.M. [and others

1995-12-31

In 1992, the Department of Energy (DOE) sponsored research to demonstrate a dispersed catalyst system using a combination of molybdenum and iron precursors for direct coal liquefaction. This dispersed catalyst system was successfully demonstrated using Black Thunder sub-bituminous coal at Wilsonville, Alabama by Southern Electric International, Inc. The DOE sponsored research continues at Exxon Research and Development Laboratories (ERDL). A six month continuous bench-scale program using ERDL`s Recycle Coal Liquefaction Unit (RCLU) is planned, three months in 1994 and three months in 1995. The initial conditions in RCLU reflect experience gained from the Wilsonville facility in their Test Run 263. Rawhide sub-bituminous coal which is similar to the Black Thunder coal tested at Wilsonville was used as the feed coal. A slate of five dispersed catalysts for direct coal liquefaction of Rawhide sub-bituminous coal has been tested. Throughout the experiments, the molybdenum addition rate was held constant at 100 wppm while the iron oxide addition rate was varied from 0.25 to 1.0 weight percent (dry coal basis). This report covers the 1994 operations and accomplishments.

Technical and economic aspects of brown coal gasification and liquefaction

International Nuclear Information System (INIS)

Speich, P.

1980-01-01

A number of gasification and liquefaction processes for Rhenish brown coal are investigated along with the technical and economic aspects of coal beneficiation. The status of coal beneficiation and the major R + D activities are reviewed. (orig.) [de

Effects of glycyrrhizin pre-treatment on transient ischemic brain ...

African Journals Online (AJOL)

Effects of glycyrrhizin pre-treatment on transient ischemic brain injury in mice. ... on transient ischemic brain injury in mice. Chiyeon Lim, Sehyun Lim, Young-Jun Lee, Bokcheul Kong, Byoungho Lee, Chang-Hyun Kim, Buyeo Kim, Suin Cho ... induced brain damage. Keywords: Glycyrrhizin, licorice, stroke, apoptosis ...

Cooperative research in coal liquefaction. Final report, May 1, 1991--April 30, 1992

Energy Technology Data Exchange (ETDEWEB)

Huffman, G.P. [ed.

1996-03-01

Extensive research continued on catalysts based on novel anion-treated (mainly sulfated) oxides and oxyhydroxides of iron [Fe{sub x}O{sub y}/SO{sub 4}]. In addition, sulfated oxides of tin as well as molybdenum promoted iron oxides were used. Incorporation of small amounts of sulfate, molybdate, or tungstate anions by wet precipitation/impregnation methods was found to increase the surface acidic character of iron oxides; more importantly, it reduced the grain sizes significantly with corresponding increases in specific surface areas. These anion-treated iron and tin oxides were more active for direct coal liquefaction and coal-heavy oil coprocessing than their untreated counterparts. With these catalyst systems, higher conversion levels are obtained as compared to the soluble precursors of iron and molybdenum at the same catalyst metalloading (3500 ppm iron and 50 ppm molybdenum with respect to coal). Sulfated iron oxides and oxyhydroxides were equally active as coal liquefaction catalysts. The sulfate, molybdate, and tungstate anions were found to have similar promotional effects on the properties and activities of iron oxides. One step in the synthesis of anion-treated iron and tin oxides is precipitation as hydroxides using either urea or ammonium hydroxide. The catalysts prepared using urea as a precipitation agent were more reproducible than those using ammonium, hydroxide in terms of activities and properties. These catalysts/catalyst precursors were characterized by several techniques to determine their physical (size and structure related) and chemical (acidity) properties. Sulfated and molybdated iron oxides were found to have grain sizes as small as 10-20 nm. An attempt was made to correlate the physicochemical properties of these catalysts with their activity for coal liquefaction.

Survey on peripheral techniques of brown coal liquefaction techniques; Kattan ekika gijutsu ni kansuru shuhen gijutsu no chosa

Energy Technology Data Exchange (ETDEWEB)

NONE

1980-09-01

Described herein are results of survey on brown coal liquefaction techniques and peripheral techniques, centered by COSTEAM process under development in USA, solubilization by alcohol and liquefaction and cracking with the aid of tetrahydroquinoline as the hydrogen donor under development in Japan, and low-temperature carbonization and new promising techniques. The COSTEAM process shows higher reaction rates, conversions and oil yields for brown coal liquefaction than the one using hydrogen gas. Some of the problems involved in this process high viscosity and oxygenated compound content of the product oil. The product oil is acceptable as fuel for power generating plants and can be produced at a moderate cost, but may be unsuitable as vehicle fuel. Coal liquefaction and solubilization processes are mainly represented by those which use hydrogen. The hydrogen cost, which is high, determines the product price. The processes which use alcohol or tetrahydroquinoline are still in the experimental stage. (NEDO)

Simplified dynamic analysis to evaluate liquefaction-induced lateral deformation of earth slopes: a computational fluid dynamics approach

Science.gov (United States)

Jafarian, Yaser; Ghorbani, Ali; Ahmadi, Omid

2014-09-01

Lateral deformation of liquefiable soil is a cause of much damage during earthquakes, reportedly more than other forms of liquefaction-induced ground failures. Researchers have presented studies in which the liquefied soil is considered as viscous fluid. In this manner, the liquefied soil behaves as non-Newtonian fluid, whose viscosity decreases as the shear strain rate increases. The current study incorporates computational fluid dynamics to propose a simplified dynamic analysis for the liquefaction-induced lateral deformation of earth slopes. The numerical procedure involves a quasi-linear elastic model for small to moderate strains and a Bingham fluid model for large strain states during liquefaction. An iterative procedure is considered to estimate the strain-compatible shear stiffness of soil. The post-liquefaction residual strength of soil is considered as the initial Bingham viscosity. Performance of the numerical procedure is examined by using the results of centrifuge model and shaking table tests together with some field observations of lateral ground deformation. The results demonstrate that the proposed procedure predicts the time history of lateral ground deformation with a reasonable degree of precision.

Highly Dispersed Pseudo-Homogeneous and Heterogeneous Catalysts Synthesized via Inverse Micelle Solutions for the Liquefaction of Coal

Energy Technology Data Exchange (ETDEWEB)

Hampden-Smith, M.; Kawola, J.S.; Martino, A.; Sault, A.G.; Yamanaka, S.A.

1999-01-05

The mission of this project was to use inverse micelle solutions to synthesize nanometer sized metal particles and test the particles as catalysts in the liquefaction of coal and other related reactions. The initial focus of the project was the synthesis of iron based materials in pseudo-homogeneous form. The frost three chapters discuss the synthesis, characterization, and catalyst testing in coal liquefaction and model coal liquefaction reactions of iron based pseudo-homogeneous materials. Later, we became interested in highly dispersed catalysts for coprocessing of coal and plastic waste. Bifunctional catalysts . to hydrogenate the coal and depolymerize the plastic waste are ideal. We began studying, based on our previously devised synthesis strategies, the synthesis of heterogeneous catalysts with a bifunctional nature. In chapter 4, we discuss the fundamental principles in heterogeneous catalysis synthesis with inverse micelle solutions. In chapter 5, we extend the synthesis of chapter 4 to practical systems and use the materials in catalyst testing. Finally in chapter 6, we return to iron and coal liquefaction now studied with the heterogeneous catalysts.

Hydrothermal liquefaction of barley straw to bio-crude oil

DEFF Research Database (Denmark)

Zhu, Zhe; Rosendahl, Lasse; Toor, Saqib

2015-01-01

Hydrothermal liquefaction (HTL) of barley straw with K2CO3 at different temperatures (280–400 C) was conducted and compared to optimize its process conditions; the aqueous phase as a co-product from this process was recycled to explore the feasibility of implementing wastewater reuse for bio...

Synergistic effect of alkaline pretreatment and Fe dosing on batch anaerobic digestion of maize straw

International Nuclear Information System (INIS)

Khatri, Shailendra; Wu, Shubiao; Kizito, Simon; Zhang, Wanqin; Li, Jiaxi; Dong, Renjie

2015-01-01

Highlights: • Synergistic effect of NaOH treatment and Fe dosage to maize straw was investigated. • Combining NaOH treatment and Fe dosing resulted in 57% and 56% higher biogas and methane yield respectively. • Combined treatment shortened the technical digestion time from 48 days to 7 days. • Methane content did not differ significantly among the straw treatments. - Abstract: The synergistic effect of alkaline pretreatment and Fe dosing on anaerobic digestion of maize straw was investigated using mesophilic batch reactors. Three straw treatments were investigated as follows: NaOH (4% and 6%) pretreatment, Fe dosage (50, 200, 1000 and 2000 mg/L), and combined NaOH pretreatment and Fe dosage. Compared to the control, NaOH pretreatment alone increased methane yield by 3.5% (313.3 mL CH_4/gVS) and 22.5% (370.9 mL CH_4/gVS) and shortened the technical digestion time (TDT) from 48 days to 19 days and 10 days in 4% NaOH and 6% NaOH pretreatment respectively. Moreover, Fe dosing (200–1000 mg/L) alone gave a methane yield higher (9.4%) than that obtained from 4% NaOH and 7.5% less than the methane yield from 6% NaOH pretreatment; however, the TDT was 10 days longer. Combining NaOH pretreatment and Fe dosage (200–1000 mg/L) significantly increased the methane yield even further to 21.8% (368.8 mL CH_4/gVS) and 56.2% (472.9 mL CH_4/gVS), and shortened TDT from 48 days to 13 days and 7 days in 4% NaOH and 6% NaOH pretreatment respectively. This synergistic effect may be attributed to the fact that the alkaline treatment improved accessibility of the biodegradable fraction of the straw while Fe contributed to increased microbial enzyme activity.

Effect of gamma irradiation on the mosquito Culex Pipiens complex L. Pretreated with radioprotectors glutathione and mexamine: The effect on certain biological aspects. Vol. 4

International Nuclear Information System (INIS)

El-Moursy, A.A.; Abdel-Rahman, A.M.; Roushdy, H.M.; Gehad, M.A.

1996-01-01

The Ld 50 /24 h of glutathione and mexamine solutions were obtained by applying concentrations of 2.25%, and 0.26%, respectively to o-h old pupae of C. Pipiens. Also, the optimum exposure time (OET) was 20 minutes for glutathione and 10 min. for mexamine. A depressing effect was recorded in the percent of adult emergence after pretreatment with either glutathione or mexamine as compared to emergence after pretreatment with either glutathione or mexamine solutions and gamma irradiation. pretreatment with either glutathione or mexamine had no significant effect on sex ratio. A depressing effect was recorded in the percent of adult emergence after pretreatment with either glutathione or mexamine as compared to emergence after pretreatment with either glutathione or mexamine solutions and gamma irradiation. pretreatment with either glutathione or mexamine had no significant effect on sex ratio. Some recovery was observed in the adult lifespan, probably due to pretreatment with radioprotectors. This recovery was more evident in males than in females. 2 figs., 3 tabs

Renewable hydrocarbon fuels from hydrothermal liquefaction: A techno-economic analysis

DEFF Research Database (Denmark)

Pedersen, Thomas Helmer; Hansen, Nick Høy; Pérez, Oscar Miralles

2018-01-01

This study demonstrates the economic feasibility of producing renewable transportation drop-in fuels from lignocellulosic biomass through hydrothermal liquefaction and upgrading. An Aspen Plus® process model is developed based on extensive experimental data to document a techno-economic assessmen...

Microwave-assisted liquefaction of wood with polyhydric alcohols and its application in preparation of polyurethane (PU) foams

Science.gov (United States)

Hui Pan; Zhifeng Zheng; Chung Y. Hse

2011-01-01

Microwave radiation was used as the heating source in southern pine wood liquefaction with PEG/glycerin binary solvent. It was found that microwave heating was more efficient than conventional oil bath heating for wood liquefaction. The wood residue content of the H2SO4 catalyzed liquefied wood dropped to zero within 5 min with microwave heating. The resulting...

The effect of dilute acid pre-treatment process in bioethanol production from durian (Durio zibethinus) seeds waste

Science.gov (United States)

Ghazali, K. A.; Salleh, S. F.; Riayatsyah, T. M. I.; Aditiya, H. B.; Mahlia, T. M. I.

2016-03-01

Lignocellulosic biomass is one of the promising feedstocks for bioethanol production. The process starts from pre-treatment, hydrolysis, fermentation, distillation and finally obtaining the final product, ethanol. The efficiency of enzymatic hydrolysis of cellulosic biomass depends heavily on the effectiveness of the pre-treatment step which main function is to break the lignin structure of the biomass. This work aims to investigate the effects of dilute acid pre-treatment on the enzymatic hydrolysis of durian seeds waste to glucose and the subsequent bioethanol fermentation process. The yield of glucose from dilute acid pre-treated sample using 0.6% H2SO4 and 5% substrate concentration shows significant value of 23.4951 g/L. Combination of dilute acid pre-treatment and enzymatic hydrolysis using 150U of enzyme able to yield 50.0944 g/L of glucose content higher compared to normal pre-treated sample of 8.1093 g/L. Dilute acid pre-treatment sample also shows stable and efficient yeast activity during fermentation process with lowest glucose content at 2.9636 g/L compared to 14.7583g/L for normal pre-treated sample. Based on the result, it can be concluded that dilute acid pre-treatment increase the yield of ethanol from bioethanol production process.

Effect of pre-treatments on seed germination of Parkia biglobosa ...

African Journals Online (AJOL)

Effect of pre-treatments on seed germination of Parkia biglobosa (Benth) ... There has been emphasis on the use of indigenous tree species to check land ... out to investigate the most effective pre-sowing treatments to break seed dormancy and to ... Matured seeds of P. biglobosa were collected from farmers at Mbalagh ...

Coal conversion rate in 1t/d PSU liquefaction reactor; 1t/d PSU ekika hannoto ni okeru sekitan tenka sokudo no kento

Energy Technology Data Exchange (ETDEWEB)

Ikeda, K.; Imada, K. [Nippon Steel Corp., Tokyo (Japan); Nogami, Y.; Inokuchi, K. [Mitsui SRC Development Co. Ltd., Tokyo (Japan)

1996-10-28

To investigate the coal liquefaction characteristics, coal slurry samples were taken from the outlets of the reactors and slurry preheater of NEDOL process 1 t/d process supporting unit (PSU), and were analyzed. Tanito Harum coal was used for liquefaction, and the slurry was prepared with recycle solvent. Liquefaction was performed using synthetic iron sulfide catalyst at reaction temperatures, 450 and 465{degree}C. Solubility of various solid samples was examined against n-hexane, toluene, and tetrahydrofuran (THF). When considering the decrease of IMO (THF-insoluble and ash) as a characteristic of coal conversion reaction, around 20% at the outlet of the slurry preheater, around 70% within the first reactor, and several percents within the successive second and third reactors were converted against supplied coal. Increase of reaction temperature led to the increase of evaporation of oil fraction, which resulted in the decrease of actual slurry flow rate and in the increase of residence time. Thus, the conversion of coal was accelerated by the synergetic effect of temperature and time. Reaction rate constant of the coal liquefaction was around 2{times}10{sup -1} [min{sup -1}], which increased slightly with increasing the reaction temperature from 450 to 465{degree}C. 3 refs., 5 figs., 1 tab.

Fiscal 1996 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1996 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. In the modification of facilities, detailed designs were prepared for product oil reforming facilities and some equipment and devices were procured. In addition, the 3rd liquefaction reactor cone section and the neutron attenuation-aided measuring device were refurbished. In the injection of coal, a 62-day and 23-day slurry injection operations were accomplished using Tanito Harum coal, when the impact imposed on the yield of the product, etc., by the change of liquefaction catalysts and by gas phase hydrogen concentration enriching conditions was investigated, and the unit was examined for operationality. During a 42-day operation for maintenance, the unit was operated using only the slurry heater for the investigation of the initial reaction in liquefaction, and studies were conducted about the heater exit temperature, G/L (gas-liquid ratio), and the effect to ensue from the use of a different solvent. In the effort to develop and evaluate new materials, implantation tests were conducted for metallic materials and the 3rd liquefaction reactor was subjected to a non-destructive inspection. Wastewater from the process was examined for quality, and environment-related measurements were performed for the atmosphere. (NEDO)

Microwave-assisted acid pretreatment of alkali lignin: Effect on characteristics and pyrolysis behavior.

Science.gov (United States)

Duan, Dengle; Ruan, Roger; Wang, Yunpu; Liu, Yuhuan; Dai, Leilei; Zhao, Yunfeng; Zhou, Yue; Wu, Qiuhao

2018-03-01

This study performed microwave-assisted acid pretreatment on pure lignin. The effects of microwave temperature, microwave time, and hydrochloric acid concentration on characteristics and pyrolysis behavior of lignin were examined. Results of ultimate analysis revealed better properties of all pretreated samples than those of raw lignin. Fourier transform infrared spectroscopy analysis showed breakage of βO4 bond and aliphatic side chain, decrease in OH groups, and formation of CO groups in pretreatment. Microwave temperature exerted more significant influence on lignin structure. Thermal stability of treated lignin was improved and insensitive to short microwave time and acid concentration under mild conditions. Resulting from improved alkyl-phenols and decreased alkoxy-phenols, microwave-assisted acid pretreatment of lignin yielded bio-oil with excellent quality. Total yield of phenols in pyrolysis vapors (200 °C) improved to 14.15%, whereas that of guaiacols decreased to 22.36%. This study shows that microwave-assisted acid pretreatment is a promising technology for lignin conversion. Copyright © 2017 Elsevier Ltd. All rights reserved.

Effect of steam pretreatment on oil palm empty fruit bunch for the production of sugars

International Nuclear Information System (INIS)

Shamsudin, Saleha; Md Shah, Umi Kalsom; Zainudin, Huzairi; Abd-Aziz, Suraini; Mustapa Kamal, Siti Mazlina; Shirai, Yoshihito; Hassan, Mohd Ali

2012-01-01

Lignocellulose into fuel ethanol is the most feasible conversion route strategy in terms of sustainability. Oil palm empty fruit bunch (EFB) generated from palm oil production is a huge source of cellulosic material and represents a cheap renewable feedstock which awaits further commercial exploitation. The purpose of this study was to investigate the feasibility of using steam at 0.28 MPa and 140 °C generated from the palm oil mill boiler as a pretreatment to enhance the digestibility of EFB for sugars production. The effects of steam pretreatment or autohydrolysis on chemical composition changes, polysaccharide conversion, sugar production and morphology alterations of four different types of EFB namely fresh EFB (EFB1), sterilized EFB (EFB2), shredded EFB (EFB3) and ground EFB (EFB4) were evaluated. In this study, the effects of steam pretreatment showed major alterations in the morphology of EFB as observed under the scanning electron microscope. Steam pretreated EFB2 was found to have the highest total conversion of 30% to sugars with 209 g kg −1 EFB. This production was 10.5 fold higher than for EFB1 and 1.6 fold and 1.7 fold higher than EFB3 and EFB4, respectively. The results suggested that pretreatment of EFB by autohydrolysis using steam from the mill boiler could be considered as being a suitable pretreatment process for the production of sugars. These sugars can be utilized as potential substrates for the production of various products such as fuel ethanol. -- Highlights: ► We investigate the feasibility of steam pretreatment to enhance digestibility of EFB. ► Steam pretreatment increased sugars to 3.4 fold and caused major alteration in EFB morphology under SEM. ► Autohydrolysis which does not require the addition of chemicals is an attractive pretreatment approach to EFB.

Techno-economic Analysis of Acid Gas Removal and Liquefaction for Pressurized LNG

Science.gov (United States)

Lee, S. H.; Seo, Y. K.; Chang, D. J.

2018-05-01

This study estimated the life cycle cost (LCC) of an acid gas removal and a liquefaction processes for Pressurized LNG (PLNG) production and compared the results with the cost of normal LNG production. PLNG is pressurized LNG that is liquefied at a higher pressure and temperature than normal LNG. Due to the high temperature, the energy for liquefaction is reduced. The allowable CO2 concentration in PLNG is increased up to 3 mol% when the product pressure 25 bar. An amine process with 35 wt% of diethanolamine (DEA) aqueous solution and a nitrogen expansion cycle were selected for the acid gas removal and the liquefaction processes, respectively. Two types of CO2 concentration in the feed gas were investigated to analyze their impacts on the acid gas removal unit. When the CO2 concentration was 5 mol%, the acid gas removal unit was required for both LNG and PLNG production. However, the acid gas removal unit was not necessary in PLNG when the concentration was 0.5 mol% and the pressure was higher than 15 bar. The results showed that the LCC of PLNG was reduced by almost 35% relative to that of LNG when the PLNG pressure was higher than 15 bar.

Biogas production from microalgae grown in wastewater: Effect of microwave pretreatment

International Nuclear Information System (INIS)

Passos, Fabiana; Solé, Maria; García, Joan; Ferrer, Ivet

2013-01-01

Highlights: ► Microwave irradiation enhanced the disintegration and digestibility of microalgae. ► Algal biomass solubilisation increased by 800% with microwave pretreatment. ► The main parameter influencing biomass solubilisation was the applied specific energy. ► Increased biogas production rate (27–75%) and yield (12–78%) with pretreated biomass. ► Linear correlation between microalgae solubilisation and biogas yield. - Abstract: The aim of this study was to evaluate the effect of microwave pretreatment on the solubilisation and anaerobic digestion of microalgae–bacterial biomass cultivated in high rate algal ponds for wastewater treatment. The microwave pretreatment comprised three specific energies (21,800, 43,600 and 65,400 kJ/kg TS), combining three output power values with different exposure times. Response surface analysis showed that the main parameter influencing biomass solubilisation was the applied specific energy. Indeed, a similar solubilisation increase was obtained for the same specific energy, regardless of the output power and exposure time (280–350% for 21,800 kJ/kg TS, 580–610% for 43,600 kJ/kg TS and 730–800% for 65,400 kJ/kg TS). In biochemical methane potential tests, the initial biogas production rate (27–75% increase) and final biogas yield (12–78% increase) were higher with pretreated biomass. A linear correlation was found between biomass solubilisation and biogas yield. It can be concluded that microwave irradiation enhanced the disintegration and digestibility of microalgae

Subtask 3.9 - Direct Coal Liquefaction Process Development

Energy Technology Data Exchange (ETDEWEB)

Aulich, Ted; Sharma, Ramesh

2012-07-01

The Energy and Environmental Research Center (EERC), in partnership with the U.S. Department of Energy (DOE) and Accelergy Corporation, an advanced fuels developer with technologies exclusively licensed from ExxonMobil, undertook Subtask 3.9 to design, build, and preliminarily operate a bench-scale direct coal liquefaction (DCL) system capable of converting 45 pounds/hour of pulverized, dried coal to a liquid suitable for upgrading to fuels and/or chemicals. Fabrication and installation of the DCL system and an accompanying distillation system for off-line fractionation of raw coal liquids into 1) a naphtha middle distillate stream for upgrading and 2) a recycle stream was completed in May 2012. Shakedown of the system was initiated in July 2012. In addition to completing fabrication of the DCL system, the project also produced a 500-milliliter sample of jet fuel derived in part from direct liquefaction of Illinois No. 6 coal, and submitted the sample to the Air Force Research Laboratory (AFRL) at Wright Patterson Air Force Base, Dayton, Ohio, for evaluation. The sample was confirmed by AFRL to be in compliance with all U.S. Air Force-prescribed alternative aviation fuel initial screening criteria.

Steam explosion pretreatment of softwood: the effect of the explosive decompression on enzymatic digestibility.

Science.gov (United States)

Pielhop, Thomas; Amgarten, Janick; von Rohr, Philipp Rudolf; Studer, Michael H

2016-01-01

Steam explosion pretreatment has been examined in many studies for enhancing the enzymatic digestibility of lignocellulosic biomass and is currently the most common pretreatment method in commercial biorefineries. The information available about the effect of the explosive decompression on the biochemical conversion is, however, very limited, and no studies prove that the latter is actually enhanced by the explosion. Hence, it is of great value to discern between the effect of the explosion on the one hand and the steaming on the other hand, to identify their particular influences on enzymatic digestibility. The effect of the explosive decompression in the steam explosion pretreatment of spruce wood chips on their enzymatic cellulose digestibility was studied systematically. The explosion had a high influence on digestibility, improving it by up to 90 % compared to a steam pretreatment without explosion. Two factors were identified to be essentially responsible for the effect of the explosion on enzymatic digestibility: pretreatment severity and pressure difference of the explosion. A higher pretreatment severity can soften up and weaken the lignocellulose structure more, so that the explosion can better break up the biomass and decrease its particle size, which enhances its digestibility. In particular, increasing the pressure difference of the explosion leads to more defibration, a smaller particle size and a better digestibility. Though differences were found in the micro- and nanostructure of exploded and non-exploded biomass, the only influence of the explosion on digestibility was found to be the macroscopic particle size reduction. Steam explosion treatments with a high severity and a high pressure difference of the explosion lead to a comparatively high cellulose digestibility of the-typically very recalcitrant-softwood biomass. This is the first study to show that explosion can enhance the enzymatic digestibility of lignocellulosic biomass. If the

Assessment of thermodynamic models for the design, analysis and optimisation of gas liquefaction systems

International Nuclear Information System (INIS)

Nguyen, Tuong-Van; Elmegaard, Brian

2016-01-01

Highlights: • Six thermodynamic models used for evaluating gas liquefaction systems are compared. • Three gas liquefaction systems are modelled, assessed and optimised for each equation of state. • The predictions of thermophysical properties and energy flows are significantly different. • The GERG-2008 model is the only consistent one, while cubic, virial and statistical equations are unsatisfying. - Abstract: Natural gas liquefaction systems are based on refrigeration cycles – they consist of the same operations such as heat exchange, compression and expansion, but they have different layouts, components and working fluids. The design of these systems requires a preliminary simulation and evaluation of their performance. However, the thermodynamic models used for this purpose are characterised by different mathematical formulations, ranges of application and levels of accuracy. This may lead to inconsistent results when estimating hydrocarbon properties and assessing the efficiency of a given process. This paper presents a thorough comparison of six equations of state widely used in the academia and industry, including the GERG-2008 model, which has recently been adopted as an ISO standard for natural gases. These models are used to (i) estimate the thermophysical properties of a Danish natural gas, (ii) simulate, and (iii) optimise liquefaction systems. Three case studies are considered: a cascade layout with three pure refrigerants, a single mixed-refrigerant unit, and an expander-based configuration. Significant deviations are found between all property models, and in all case studies. The main discrepancies are related to the prediction of the energy flows (up to 7%) and to the heat exchanger conductances (up to 11%), and they are not systematic errors. The results illustrate the superiority of using the GERG-2008 model for designing gas processes in real applications, with the aim of reducing their energy use. They demonstrate as well that

Effect of Pre-treatment method on the Hydrolysis of Corn cob and Sawdust

Directory of Open Access Journals (Sweden)

Olawole Ogirima Olanipekun

2016-12-01

Full Text Available Efficient pre-treatment has been found to be crucial step before enzymatic hydrolysis of cellulose into fuels or chemicals. As a result various pretreatment methods have been developed to facilitate these bio-conversion processes, and this research focuses on the effect of two pretreatment methods such as liquid hot water and sulphuric acid pre-treatment to remove some of the components like lignin and hemicellulose which form structural barrier to enzymatic accessibility of cellulose in corn cobs and sawdust. The cellulosic materials were first dried in oven at 65 oC for 24 hours,  and using   solid to liquid ratio of 1:10, the two methods were carried out at resident times ranging from 10 - 40 minutes. The liquid hot water method involved heating the cellulosic materials in water at 120 oC and 1atmosphere in a pressure vessel, and for the second method, the dried cellulosic materials were refluxed in 5 % sulphuric acid at a temperature of 120 oC. Pretreated samples were filtered and liquid fractions were analyzed for the presence of reducing sugars, while solid residues were dried in the oven and weighed to measure the mass lost during pretreatment as a pointer to lignin breakdown. It was observed that the mass lost increased with time for both pretreatment methods, but the liquid hot water pretreatment gave higher lignin and hemicellulose removal when compared to the sulphuric acid pre-treatment. The pretreated materials were hydrolyzed with two combinations of commercial enzymes namely cellulase/ hemicellulase and cellulase/β glucosidase. The reducing sugar was measured using Dinitrosalycilic acid (DNSA method and the sugar yields from corn cobs were higher than that of sawdust when subjected to similar process conditions, and the enzyme combination of cellulase/glucosidase gave higher yields of reducing sugars.  A model equation which describes the hydrolysis process was developed from first principles and the experimental data

Anaerobic digestion of post-hydrothermal liquefaction wastewater for improved energy efficiency of hydrothermal bioenergy processes.

Science.gov (United States)

Zhou, Yan; Schideman, Lance; Zheng, Mingxia; Martin-Ryals, Ana; Li, Peng; Tommaso, Giovana; Zhang, Yuanhui

2015-01-01

Hydrothermal liquefaction (HTL) is a promising process for converting wet biomass and organic wastes into bio-crude oil. It also produces an aqueous product referred to as post-hydrothermal liquefaction wastewater (PHWW) containing up to 40% of the original feedstock carbon, which reduces the overall energy efficiency of the HTL process. This study investigated the feasibility of using anaerobic digestion (AD) to treat PHWW, with the aid of activated carbon. Results showed that successful AD occurred at relatively low concentrations of PHWW (≤ 6.7%), producing a biogas yield of 0.5 ml/mg CODremoved, and ∼53% energy recovery efficiency. Higher concentrations of PHWW (≥13.3%) had an inhibitory effect on the AD process, as indicated by delayed, slower, or no biogas production. Activated carbon was shown to effectively mitigate this inhibitory effect by enhancing biogas production and allowing digestion to proceed at higher PHWW concentrations (up to 33.3%), likely due to sequestering toxic organic compounds. The addition of activated carbon also increased the net energy recovery efficiency of AD with a relatively high concentration of PHWW (33.3%), taking into account the energy for producing activated carbon. These results suggest that AD is a feasible approach to treat PHWW, and to improve the energy efficiency of the HTL processes.

Microbial liquefaction of peat for the production of synthetic fuels

Energy Technology Data Exchange (ETDEWEB)

Gunasekaran, M.

1988-01-01

Objectives of this study were: to evaluate the potential of using various microorganisms to hydrolyse and liquify peat; to determine the optimal conditions for peat hydrolysis and liquefaction; to study the co-metabolizable substances; to separate the compounds present in liquified peat by alumina and silica acid chromatography and capillary gas chromatography; and to identify the compounds in liquified peat by capillary GC-Mass spectrometry. Organisms used in the study include: Coprinus comatus, Coriolus hirsutus, Ganoderma lucidum, Lentinus edodes, Lenzites trabea, Phanerochaete chrysosporium, Pleurotus ostreatus, P. sapidus, Polyporus adjustus, Neurospora sitophila, Rhizophus arrhizus, Bacillus subtilis, Acinetobacter sp. and Alcaligenes sp. The fungi were maintained and cultivated in potato dextrose agar at 30 C. The bacteria were maintained in nutrient agar at 30 C. We have also initiated work on coal solubilization in addition to the studies on peat liquefaction. A relatively new substratum or semi-solid base for culture media called Pluronic F-127, or Polyol (BASF, New Jersey). Objectives of this study were: (1) to study the growth patterns of Candida ML 13 on pluronic as substratum; (2) to determine the rate of microbial coal solubilization on pluronic F-127 amended in different growth media; (3) to separate the mycelial mat of Candida ML 13 from unsolubilized coal particles and solubilized coal products from pluronic F-127; (4) to determine the effects of pH on microbial coal solubilization in pluronic F-127 media; (5) the effect of concentration of pluronic F-127 in media on coal solubilization; and, (6) to study the role of extracellular factors secreted by Candida ML 13 on coal solubilization in pluronic F-127 media. Results are discussed. 4 refs.

Simulation and statistical analysis for the optimization of nitrogen liquefaction plant with cryogenic Claude cycle using process modeling tool: ASPEN HYSYS

International Nuclear Information System (INIS)

Joshi, D.M.

2017-01-01

Cryogenic technology is used for liquefaction of many gases and it has several applications in food process engineering. Temperatures below 123 K are considered to be in the field of cryogenics. Extreme low temperatures are a basic need for many industrial processes and have several applications, such as superconductivity of magnets, space, medicine and gas industries. Several methods can be used to obtain the low temperatures required for liquefaction of gases. The process of cooling or refrigerating a gas to a temperature below its critical temperature so that liquid can be formed at some suitable pressure, which is below the critical pressure, is the basic liquefaction process. Different cryogenic cycle configurations are designed for getting the liquefied form of gases at different temperatures. Each of the cryogenic cycles like Linde cycle, Claude cycle, Kapitza cycle or modified Claude cycle has its own advantages and disadvantages. The placement of heat exchangers, Joule-Thompson valve and turboexpander decides the configuration of a cryogenic cycle. Each configuration has its own efficiency according to the application. Here, a nitrogen liquefaction plant is used for the analysis purpose. The process modeling tool ASPEN HYSYS can provide a software simulation approach before the actual implementation of the plant in the field. This paper presents the simulation and statistical analysis of the Claude cycle with the process modeling tool ASPEN HYSYS. It covers the technique used to optimize the liquefaction of the plant. The simulation results so obtained can be used as a reference for the design and optimization of the nitrogen liquefaction plant. Efficient liquefaction will give the best performance and productivity to the plant.

Simulation and statistical analysis for the optimization of nitrogen liquefaction plant with cryogenic Claude cycle using process modeling tool: ASPEN HYSYS

Science.gov (United States)

Joshi, D. M.

2017-09-01

Cryogenic technology is used for liquefaction of many gases and it has several applications in food process engineering. Temperatures below 123 K are considered to be in the field of cryogenics. Extreme low temperatures are a basic need for many industrial processes and have several applications, such as superconductivity of magnets, space, medicine and gas industries. Several methods can be used to obtain the low temperatures required for liquefaction of gases. The process of cooling or refrigerating a gas to a temperature below its critical temperature so that liquid can be formed at some suitable pressure, which is below the critical pressure, is the basic liquefaction process. Different cryogenic cycle configurations are designed for getting the liquefied form of gases at different temperatures. Each of the cryogenic cycles like Linde cycle, Claude cycle, Kapitza cycle or modified Claude cycle has its own advantages and disadvantages. The placement of heat exchangers, Joule-Thompson valve and turboexpander decides the configuration of a cryogenic cycle. Each configuration has its own efficiency according to the application. Here, a nitrogen liquefaction plant is used for the analysis purpose. The process modeling tool ASPEN HYSYS can provide a software simulation approach before the actual implementation of the plant in the field. This paper presents the simulation and statistical analysis of the Claude cycle with the process modeling tool ASPEN HYSYS. It covers the technique used to optimize the liquefaction of the plant. The simulation results so obtained can be used as a reference for the design and optimization of the nitrogen liquefaction plant. Efficient liquefaction will give the best performance and productivity to the plant.

When is the liquefaction of coal economic. [Including safe and secure supplies, low interest, multiplier effect of money spent inside the country, employment, etc

Energy Technology Data Exchange (ETDEWEB)

1980-09-01

Usually the commercialization of a technology is determined by the economic viability. However, looking at coal conversion we recognize that there is also a strategic factor to be considered. Before entering into what is almost a political debate about the strategic value of coal conversion, let us look at the economic data. Table 2 shows specific cost numbers for coal gasification, coal liquefaction and electricity from coal. When the total cost of the different fuels is calculated with capital charges as would be required by private industry, one would arrive at indeed high figures, high compared to the present day cost of liquid energy. However, in the capital intensive electricity industry, capital can be accounted for on a capital charge basis of 7 to 17%. If this type of soft financing is applied to coal, coal liquids and coal gas, the figures already become much more attractive. Money internally spent within a country will turnover a few times. This is described by economists as the effect of the multiplier. To even further improve the prospects of home-made liquids one can add the value of avoiding unemployment. A labor intensive industry like the coal gasification and liquefaction industry may give a boost to the number of jobs and as a result have even another additional value to the country involved. Such an analysis leads to the conclusion that coal gasification and liquefaction could develop as a utility type industry under rather tight Government control. This has its strategic advantages with respect to stability and security of supply. On the other hand it may discourage private industry from getting involved in this business. Much will therefore depend on the political decision making process and that maybe is one of the biggest unknowns left in answer to the question when coal conversion will become of economic significance.

Hydrothermal Liquefaction Treatment Hazard Analysis Report

Energy Technology Data Exchange (ETDEWEB)

Lowry, Peter P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Wagner, Katie A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2016-09-12

Hazard analyses were performed to evaluate the modular hydrothermal liquefaction treatment system. The hazard assessment process was performed in 2 stages. An initial assessment utilizing Hazard Identification and Preliminary Hazards Analysis (PHA) techniques identified areas with significant or unique hazards (process safety-related hazards) that fall outside of the normal operating envelope of PNNL and warranted additional analysis. The subsequent assessment was based on a qualitative What-If analysis. The analysis was augmented, as necessary, by additional quantitative analysis for scenarios involving a release of hazardous material or energy with the potential for affecting the public. The following selected hazardous scenarios received increased attention: •Scenarios involving a release of hazardous material or energy, controls were identified in the What-If analysis table that prevent the occurrence or mitigate the effects of the release. •Scenarios with significant consequences that could impact personnel outside the immediate operations area, quantitative analyses were performed to determine the potential magnitude of the scenario. The set of “critical controls” were identified for these scenarios (see Section 4) which prevent the occurrence or mitigate the effects of the release of events with significant consequences.

Design optimization of single mixed refrigerant natural gas liquefaction process using the particle swarm paradigm with nonlinear constraints

International Nuclear Information System (INIS)

Khan, Mohd Shariq; Lee, Moonyong

2013-01-01

The particle swarm paradigm is employed to optimize single mixed refrigerant natural gas liquefaction process. Liquefaction design involves multivariable problem solving and non-optimal execution of these variables can waste energy and contribute to process irreversibilities. Design optimization requires these variables to be optimized simultaneously; minimizing the compression energy requirement is selected as the optimization objective. Liquefaction is modeled using Honeywell UniSim Design ™ and the resulting rigorous model is connected with the particle swarm paradigm coded in MATLAB. Design constraints are folded into the objective function using the penalty function method. Optimization successfully improved efficiency by reducing the compression energy requirement by ca. 10% compared with the base case. -- Highlights: ► The particle swarm paradigm (PSP) is employed for design optimization of SMR NG liquefaction process. ► Rigorous SMR process model based on UniSim is connected with PSP coded in MATLAB. ► Stochastic features of PSP give more confidence in the optimality of complex nonlinear problems. ► Optimization with PSP notably improves energy efficiency of the SMR process.

Pretreatment of the macroalgae Chaetomorpha linum for the production of bioethanol - Comparison of five pretreatment technologies

DEFF Research Database (Denmark)

Schultz-Jensen, Nadja; Thygesen, Anders; Thomsen, Sune Tjalfe

2013-01-01

-assisted pretreatment (PAP) and ball milling (BM), to determine effects of the pretreatment methods on the conversion of C. linum into ethanol by simultaneous saccharification and fermentation (SSF). WO and BM showed the highest ethanol yield of 44. g ethanol/100. g glucan, which was close to the theoretical ethanol......A qualified estimate for pretreatment of the macroalgae Chaetomorpha linum for ethanol production was given, based on the experience of pretreatment of land-based biomass. C. linum was subjected to hydrothermal pretreatment (HTT), wet oxidation (WO), steam explosion (STEX), plasma...... yield of 57. g ethanol/100. g glucan. A 64% higher ethanol yield, based on raw material, was reached after pretreatment with WO and BM compared with unpretreated C. linum, however 50% of the biomass was lost during WO. Results indicated that the right combination of pretreatment and marine macroalgae...

Biological production of alcohols from coal through indirect liquefaction

Energy Technology Data Exchange (ETDEWEB)

Barik, S; Prieto, S; Harrison, S B; Clausen, E C; Gaddy, J L

1988-08-01

The purpose of this project is to demonstrate the feasibility of producing liquid fuels from the components of synthesis gas through biological indirect liquefaction. The results of pure culture and natural source screening studies aimed at finding organisms capable of carrying out the conversions are presented and discussed. 17 refs., 2 figs., 8 tabs.

Fiscal 1995 report. Liquefaction key technology subcommittee; 1995 nendo ekika kiban gijutsu bukai hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-03-01

The subcommittee held the 1st meeting in September 1955 and the 2nd in March 1996, when fiscal 1995 research plans and research results were introduced and deliberated. In the study for designing a high-dispersion catalyst and the elucidation of the mechanism of activity expression, catalysts of highly dispersed iron supported on the brown coal surface in various ways were compared with each other in terms of liquefaction activity. Furthermore, geometric changes in the iron catalyst during the sulfurizing process were examined using the XRD (X-ray diffraction) and TEM (transient electromagnetic) methods. An improved catalyst was found to achieve a liquefaction yield near the Yallourn coal liquefaction limit in a high boiling solvent system. Concerning the study of coal oil product applications and refining technologies, reports were delivered on research results relating to the problem of blocking to occur during naphtha fraction refining and measures therefor, inhibition of active metal geometric changes during reaction, methods for separating hetero-compounds from coal oil and application thereof, and so forth. (NEDO)

Mild Biomass Liquefaction Process for Economic Production of Stabilized Refinery-Ready Bio-oil

Energy Technology Data Exchange (ETDEWEB)

Gangwal, Santosh [Southern Research, Durham, NC (United States); Meng, Jiajia [Southern Research, Durham, NC (United States); McCabe, Kevin [Southern Research, Durham, NC (United States); Larson, Eric [Princeton Univ., NJ (United States). Princeton Environmental Inst.; Mastro, Kelly [Southern Research, Durham, NC (United States)

2016-04-25

Southern Research (SR) in cooperation with U.S. Department of Energy (DOE), Bioenergy Technology Office (BETO), investigated a biomass liquefaction process for economic production of stabilized refinery-ready bio-oil. The project was awarded by DOE under a Funding Opportunity Announcement (DE-FOA-0000686) for Bio-oil Stabilization and Commoditization that intended to evaluate the feasibility of using bio-oil as a potential feedstock in an existing petroleum refinery. SR investigated Topic Area 1 of the FOA at Technology Readiness Level 2-3 to develop thermochemical liquefaction technologies for producing a bio-oil feedstock from high-impact biomass that can be utilized within a petroleum refinery. Bio-oil obtained from fast pyrolysis of biomass is a green intermediate that can be further upgraded into a biofuel for blending in a petroleum refinery using a hydro-deoxygenation (HDO) route. Co-processing pyrolysis bio-oil in a petroleum refinery is an attractive approach to leverage the refinery’s existing capital. However, the petroleum industry is reluctant to accept pyrolysis bio-oil because of a lack of a standard definition for an acceptable bio-oil feedstock in existing refinery processes. Also per BETO’s multiyear program plan, fast pyrolysis-based bio-fuel is presently not cost competitive with petroleum-based transportation fuels. SR aims to develop and demonstrate a cost-effective low-severity thermal liquefaction and hydrodeoxygenation (HDO) process to convert woody biomass to stabilized bio-oils that can be directly blended with hydrotreater input streams in a petroleum refinery for production of gasoline and/or diesel range hydrocarbons. The specific project objectives are to demonstrate the processes at laboratory scale, characterize the bio-oil product and develop a plan in partnership with a refinery company to move the technology towards commercialization.

Effect of pelleting on the recalcitrance and bioconversion of dilute-acid pretreated corn stover

Energy Technology Data Exchange (ETDEWEB)

Allison E Ray; Amber Hoover; Gary Gresham

2012-07-01

Background: Knowledge regarding the performance of densified biomass in biochemical processes is limited. The effects of densification on biochemical conversion are explored here. Methods: Pelleted corn stover samples were generated from bales that were milled to 6.35 mm. Low-solids acid pretreatment and simultaneous saccharification and fermentation were performed to evaluate pretreatment efficacy and ethanol yields achieved for pelleted and ground stover (6.35 mm and 2 mm) samples. Both pelleted and 6.35-mm ground stover were evaluated using a ZipperClave® reactor under high-solids, process-relevant conditions for multiple pretreatment severities (Ro), followed by enzymatic hydrolysis of the washed, pretreated solids. Results: Monomeric xylose yields were significantly higher for pellets (approximately 60%) than for ground formats (approximately 38%). Pellets achieved approximately 84% of theoretical ethanol yield (TEY); ground stover formats had similar profiles, reaching approximately 68% TEY. Pelleting corn stover was not detrimental to pretreatment efficacy for both low- and high-solids conditions, and even enhanced ethanol yields.

Effect of EDTA and phosphoric Acid pretreatment on the bonding effectiveness of self-etch adhesives to ground enamel.

Science.gov (United States)

Ibrahim, Ihab M; Elkassas, Dina W; Yousry, Mai M

2010-10-01

This in vitro study determined the effect of enamel pretreatment with phosphoric acid and ethylenediaminetetraacetic acid (EDTA) on the bond strength of strong, intermediary strong, and mild self-etching adhesive systems. Ninety sound human premolars were used. Resin composite cylinders were bonded to flat ground enamel surfaces using three self-etching adhesive systems: strong Adper Prompt L-Pop (pH=0.9-1.0), intermediary strong AdheSE (pH=1.6-1.7), and mild Frog (pH=2). Adhesive systems were applied either according to manufacturer instructions (control) or after pretreatment with either phosphoric acid or EDTA (n=10). After 24 hours, shear bond strength was tested using a universal testing machine at a cross-head speed of 0.5 mm/minute. Ultra-morphological characterization of the surface topography and resin/enamel interfaces as well as representative fractured enamel specimens were examined using scanning electron microscopy (SEM). Neither surface pretreatment statistically increased the mean shear bond strength values of either the strong or the intermediary strong self-etching adhesive systems. However, phosphoric acid pretreatment significantly increased the mean shear bond strength values of the mild self-etching adhesive system. SEM examination of enamel surface topography showed that phosphoric acid pretreatment deepened the same etching pattern of the strong and intermediary strong adhesive systems but converted the irregular etching pattern of the mild self-etching adhesive system to a regular etching pattern. SEM examination of the resin/enamel interface revealed that deepening of the etching pattern was consistent with increase in the length of resin tags. EDTA pretreatment had a negligible effect on ultra-morphological features. Use of phosphoric acid pretreatment can be beneficial with mild self-etching adhesive systems for bonding to enamel.

Hydrothermal liquefaction of microalgae to produce biofuels: state of the art and future prospects

Science.gov (United States)

Vlaskin, M. S.; Chernova, N. I.; Kiseleva, S. V.; Popel', O. S.; Zhuk, A. Z.

2017-09-01

The article presents a review of the state of the art and lines of research on hydrothermal liquefaction (HTL) of microalgae (MA). The main advantages of this technology for production of biofuel are that it does not require predrying of the feedstock and ensures a relatively high product yield—the ratio of the end product weight to the feedstock weight—owing to the fact that all the microalgal components, viz., lipids, proteins, and carbohydrates, are converted into biofuel. MA hydrothermal liquefaction is considered to be a promising technology for conversion of biomass and is a subject of a series of research studies and, judging by the available publications, the scope of research in this field is expanding currently. However, many significant problems remain unsolved. In particular, an active searched is being conducted for suitable strains that will ensure not only a high lipid yield—necessary to convert microalgae into biodiesel—but also higher biomass productivity and a higher biofuel yield; the chemical reactions that occur during the hydrothermal treatment are being studied; and the effect of significant process variables, such as temperature, heating rate, holdup time at the maximum temperature, biomass concentration in the water suspension, biochemical and elemental compositions of the microalgae, use of catalysts, etc., on the liquefaction processes is being studied. One of the urgent tasks is also the reduction of the nitrogen content in the resulting biofuel. Studies aimed at the development of a continuous process and rational heat-processing plants for thermal microalgal conversion are being conducted to increase the energy efficiency of the HTL process, in particular, to provide the heat recovery and separation of the end product.

Achievement report for fiscal 1982 on Sunshine Program. Coal energy; 1982 nendo sunshine keikaku seika hokokusho. Sekitan energy

Energy Technology Data Exchange (ETDEWEB)

NONE

1982-07-01

This research program consists of (1) the solid catalyst-aided reforming of various petroleum based oils and heavy coal oils into Solvolysis solvents and the secondary hydrogenolysis, (2) a search for pre-treatment for improvement on the sub-bituminous coal liquefaction yield, and (3) a search for measures for improvement on the brown coal liquefaction yield. Studied in this fiscal year are (1) the high-temperature short-contact time liquefaction of brown coal, (2) the role of catalyst support for selective upgrading of SRC (solvent refined coal), and (3) reforming of thermal melting feature of low rank coal by preliminary deashing at room temperature. In relation with Item (1), it is found that the dehydrogenation or reaction to carbonization of molecules involved in hydrogen donation is structure-sensitive but that thermolysis of coal is accelerated under high-temperature conditions to allow transfer hydrogen to contribute uniformly. It is deemed also that matching is excellent between hydrogen transfer and thermolysis, that the solvent dissolution level is elevated, and that the reaction short in duration inhibits consecutive polymerization reaction. These are supposed to be effective in improving on the liquefaction yield and in rendering heavy constituents lighter. In relation with Item (2), it is found that the experimentally manufactured catalysts are effective in reducing the weight of heavy constituents. In relation with Item (3), a carbonization reforming method is experimentally implemented in which the ash that affects carbonization is further removed by a pre-treatment at room temperature. (NEDO)

Effect of different pretreatments on dried chilli (Capsicum annum L.) quality

Science.gov (United States)

Anoraga, S. B.; Sabarisman, I.; Ainuri, M.

2018-03-01

Chilli (Capsicum annum L.) has significant price fluctuation. When the chilli price is declined, it causes food waste from unsold chilli. Therefore, drying chilli is a solution for this condition. Futhermore, it can be processed for various product like chilli powder, chilli sauce, etc. The aim of this study was to investigate the effect of different pretreatments on dried chilli quality. Chilli was blenched with hot water and steam before drying. The purpose of this pretreatments is to inactivate enzyme that prevents color and vitamin C losses. The quality parameters were moisture content, colour, vitamin C content, and capsaicin. Changes were observed by gravimetri method for moisture content, chromameter in L* a * b * colour model, and iodine titration for vitamin C. After drying for 20 hours at 60°C, chilli with steam blanching pretreatment dried rapidly than other samples. Unpretreated chilli had higher vitamin C content and better color than blanched chilli.

Liquefaction of lignohemicellulosic waste by processing with carbon monoxide and water

Energy Technology Data Exchange (ETDEWEB)

El-Saied, H

1977-09-01

The liquefaction of lignohemicellulosic waste by processing with carbon monoxide and water for 10 minutes at 250/sup 0/-440/sup 0/C and 40 to 70 atm initial pressure in a rocking autoclave produced benzene-soluble heavy oil in yields up to 80%. High conversion and yields were favored by high thermal stress, short reaction times, and sufficient hydrogen to prevent radical recombination in the critical liquefaction stages. The addition of sodium or calcium hydroxide, sodium carbonate, iron oxide, etc. in small amounts gave good oil yields under less severe conditions. Lignins from rice straw, bagasse, and other grasses gave higher yields than the woody lignin obtained from cotton stalks. In products obtained by liquefying black liquor lignohemicellulose from an Eyptian rice straw pulping plant, the hydrogen-carbon atomic ratio was 1.0 to 1.3:1.

Achievement report for fiscal 1984 on Sunshine Program. Research on coal liquefaction reaction and the reforming and utilization of products; 1984 nendo sekitan no ekika hanno to seiseibutsu no kaishitsu riyo no kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1985-03-01

Upon the development into a single law of the three liquefaction related laws, studies are started on coal liquefaction reaction and the reforming and utilization of the products. In the research on coal liquefaction reaction, the solvent ratio, change in reaction time, and change in liquefaction product constitution in case of repeated circulation of the solvent are tracked, and their relations with the liquefaction rate and yield are studied, these efforts involving the Taiheiyo coal, Yallourn coal, and the Miike coal. The Taiheiyo coal is subjected to a short-duration liquefaction reaction test. In the research on product reforming, the medium-gravity fraction from coal liquefaction is subjected to hydrogenation, and the effect of the reaction conditions on the properties and constitution of the thus-treated oil are studied. An SRC (solvent refined coal) solution of the Taiheiyo coal is subjected to hydrogenation in the presence of a Ni-Mo catalyst, and the SRC cracking rate and product properties are compared with those obtained from another solution treated with a Co-Mo catalyst. In the research on product utilization, the medium-gravity fraction from coal liquefaction is subjected to hydrogenation under three sets of different reaction conditions in the presence of a Ni-Mo/Al{sub 2}O{sub 3} based catalyst. In this process, specimens are prepared by mixing the original oil, its hydrogenated product, and a petroleum-based light oil, and a study is made about the usability of the specimens and their mixtures with petroleum-based heater oil as light oil or heater oil. (NEDO)

Experimental Study of Subcritical Water Liquefaction of Biomass

DEFF Research Database (Denmark)

Zhu, Zhe; Toor, Saqib; Rosendahl, Lasse

2014-01-01

In this work, hydrothermal liquefaction (HTL) of wood industry residues (wood, bark, sawdust) and macroalgae for producing biofuels has been investigated under subcritical water conditions (at temperature of 300 C), with and without the presence of catalyst. The effects of catalyst and biomass type...... bio-crudes were analyzed. The results showed that the higher heating values (HHVs) were in the range of 24.15 to 31.79 MJ/kg, and they were enhanced in the presence of catalyst, except for that of the macroalgae. The solid residues were characterized by heating value, SEM and FTIR. It was found...... that the addition of K2CO3 lowered the solids quality in terms of the heating values, while it did not have apparent effect on the functional groups of solid residues. SEM analysis of the raw biomass and solid residues revealed that the char formation for wood, sawdust and macroalgae had initially finished when...

Role of heat exchangers in helium liquefaction cycles: Simulation studies using Collins cycle

International Nuclear Information System (INIS)

Thomas, Rijo Jacob; Ghosh, Parthasarathi; Chowdhury, Kanchan

2012-01-01

Highlights: ► Role of heat exchangers in basic helium liquefier analyzed to design large-scale ones. ► Heat exchangers that determine inlet temperature to expanders are more significant. ► Limiting values of nondimensional UA for each heat exchanger have been determined. ► Extra area distributed such that effectiveness of all heat exchangers increase uniformly. ► Heat exchanger performance variation have little influence on the optimum expander flow. - Abstract: Energy efficiency of large-scale helium liquefiers generally employed in fusion reactors and accelerators is determined by the performance of their constituting components. Simulation with Aspen HYSYS ® V7.0, a commercial process simulator, helps to understand the effects of heat exchanger parameters on the performance of a helium liquefier. Effective UA (product of overall heat transfer coefficient U, heat transfer surface area A and deterioration factor F) has been taken as an independent parameter, which takes into account all thermal irreversibilities and configuration effects. Nondimensionalization of parameters makes the results applicable to plants of any capacity. Rate of liquefaction is found to increase linearly with the effectiveness of heat exchangers. Performance of those heat exchangers that determine the inlet temperatures to expanders have more influence on the liquid production. Variation of sizes of heat exchangers does not affect the optimum rate of flow through expanders. Increasing UA improves the rate of liquid production; however, the improvement saturates at limiting UA. Maximum benefit in liquefaction is obtained when the available heat transfer surface area is distributed in such a way that the effectiveness remains equal for all heat exchangers. Conclusions from this study may be utilized in analyzing and designing large helium plants.

Fiscal 1998 achievement report. Coal liquefaction technology development - Bituminous coal liquefaction technology development - Study for supporting pilot plant - Study using 1t/d PSU (Study of operation using PSU); 1998 nendo seika hokokusho. Sekitan ekika gijutsu kaihatsu - Rekiseitan ekika gijutsu no kaihatsu - Pilot plant no shien kenkyu - 1t/d process support unit (PSU) ni yoru kenkyu (PSU ni yoru unten kenkyu)

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-06-01

The operation of a 1t/d PSU (process support unit) was studied for the NEDOL coal liquefaction process. For the modification of facilities, product oil reforming facilities were installed. In the coal injection operation, a 59-day slurry operation was carried out using Tanito Harum coal, which was for the evaluation of the reforming effect under the product reforming conditions, operationality, and liquefaction characteristics. A 37-day slurry operation was also performed using Chinese coal, which was intended to pursue improved cost performance and to collect the light oil fraction in the flow of reforming operation. In the operation for maintenance, investigations were conducted into conditions for hydrogenation in a 1-through operation involving the solvent hydrogenation process and the normal pressure distillation facilities and into the effect of pre-hydrogenation solvent properties, which aimed at grasping the effect of product oil reforming measures and their influence on operationality. In the survey of environments, the properties of wastewater from the liquefaction process using Tanito Harum coal were studied and toxicity evaluation tests were conducted for activated sludge. (NEDO)

Coal liquefaction process streams characterization and evaluation. Quarterly technical progress report, October 1--December 31, 1991

Energy Technology Data Exchange (ETDEWEB)

Robbins, G.A.; Brandes, S.D.; Winschel, R.A.; Burke, F.P.

1992-03-01

CONSOL R&D is conducting a three-year program to characterize process and product streams from direct coal liquefaction process development projects. The program objectives are two-fold: (1) to obtain and provide appropriate samples of coal liquids for the evaluation of analytical methodology, and (2) to support ongoing DOE-sponsored coal liquefaction process development efforts. The two broad objectives have considerable overlap and together serve to provide a bridge between process development and analytical chemistry.

Differential effect of glucocorticoids on tumour necrosis factor production in mice: up-regulation by early pretreatment with dexamethasone.

Science.gov (United States)

Fantuzzi, G; Demitri, M T; Ghezzi, P

1994-04-01

Glucocorticoids (GC) are well known inhibitors of tumour necrosis factor (TNF) production. We investigated the role of endogenous GC in the regulation of TNF production in mice treated with lipopolysaccharide (LPS) using a pretreatment with dexamethasone (DEX) to down-regulate the hypothalamus-pituitary-adrenal axis (HPA). Short-term DEX pretreatment (up to 12 h before LPS) inhibited TNF production, but earlier (24-48 h) pretreatments potentiated it. This up-regulating effect was not observed in adrenalectomized mice or when GC synthesis was inhibited with cyanoketone (CK). This effect could not be explained only by the suppression of LPS-induced corticosterone (CS) levels induced by DEX, since a 48-h pretreatment potentiated TNF production without affecting LPS-induced CS levels. On the other hand, mice chronically pretreated with DEX were still responsive to its inhibitory effect on TNF production, thus ruling out the possibility of a decreased responsiveness to GC.

Effect of pretreating of host oil on coprocessing

Energy Technology Data Exchange (ETDEWEB)

Hajdu, P.E.; Tierney, J.W.; Wender, I. [Univ. of Pittsburgh, PA (United States)

1995-12-31

The principal objective of this research was to determine if coprocessing performance (i.e., coal conversion and oil yield) could be significantly improved by pretreating the heavy resid prior to reacting it with coal. For this purpose, two petroleum vacuum resids (1000{degrees}F+), one from the Amoco Co. and another from the Citgo Co., were used as such and after they had been pretreated by catalytic hydrogenation and hydrocracking reactions. The pretreatments were aimed at improving the host oil by; (1) converting any aromatic structures in the petroleum to hydroaromatic compounds capable of donating hydrogen, (2) cracking the heavy oil to lower molecular weight material that might serve as a better solvent, (3) reducing the coking propensity of the heavy oil through the hydrogenation of polynuclear aromatic compounds, and (4) removing metals and heteroatoms that might poison a coprocessing catalyst. Highly dispersed catalysts, including fine particle Fe- and Mo-based, and dicobalt octacarbonyl, Co{sub 2}(CO){sub 8}, were used in this study. The untreated and pretreated resids were extensively characterized in order to determine chemical changes brought about by the pretreatments. The modified heavy oils were then coprocessed with an Illinois No. 6 coal as well as with a Wyodak coal, and compared to coprocessing with untreated resids under the same hydroliquefaction conditions. The amount of oil derived from coal was estimated by measuring the level of phenolic oxygen (derived mainly from coal) present in the oil products. Results are presented and discussed.

Pretreatment of wheat straw for fermentation to methane

International Nuclear Information System (INIS)

Hashimoto, A.G.

1986-01-01

The effects of pretreating wheat straw with gamma-ray irradiation, ammonium hydroxide, and sodium hydroxide on methane yield, fermentation rate constant, and loss of feedstock constituents were evaluated using laboratory-scale batch fermentors. Results showed that methane yield increased as pretreatment alkali concentration increased, with the highest yield being 37% over untreated straw for the pretreatment consisting of sodium hydroxide dosage of 34 g OH - /kg volatile solids, at 90 0 C for 1 h. Gamma-ray irradiation had no significant effect on methane yield. Alkaline pretreatment temperatures above 100 0 C caused a decrease in methane yield. After more than 100 days of fermentation, all of the hemicellulose and more than 80% of the cellulose were degraded. The loss in cellulose and hemicellulose accounted for 100% of the volatile solids lost. No consistent effect of pretreatments on batch fermentation rates was noted. Semicontinuous fermentations of straw-manure mixtures confirmed the relative effectiveness of sodium- and ammonium-hydroxide pretreatments

Role of expanders in helium liquefaction cycles: Parametric studies using Collins cycle

International Nuclear Information System (INIS)

Thomas, Rijo Jacob; Ghosh, Parthasarathi; Chowdhury, Kanchan

2011-01-01

Large scale helium liquefaction/refrigeration plant is a key subsystem of fusion devices. Performance of these plants is dependent on a number of geometric and operating parameters of its constituting components such as compressors, heat exchangers, expanders, valves, etc. Expander has been chosen as the subject matter of analyses in the present study. As the sensible cold of helium vapor is lost in liquefiers, the expanders in liquefaction cycles have to provide more refrigeration than those in refrigeration cycles. The expander parameters such as rate of mass flow, operating pressure, inlet temperature, etc. are inter-dependent, and hence, it is difficult to predict the system behavior with variation of a particular parameter. This necessitates the use of process simulators. Parametric studies have been performed on Collins helium liquefaction cycle using Aspen HYSYS. Collins cycle has all the basic characteristics of a large-scale helium liquefier and the results of this study may be extrapolated to understand the behavior of large scale helium liquefiers. The study shows that the maximum liquid production is obtained when 80% of the compressor flow is diverted through the expanders and it is equally distributed between the two expanders. The relationships between the liquid production and the isentropic efficiency of expanders are almost linear and both the higher and lower temperature expanders exhibit similar trends.

Role of expanders in helium liquefaction cycles: Parametric studies using Collins cycle

Energy Technology Data Exchange (ETDEWEB)

Thomas, Rijo Jacob, E-mail: rijojthomas@gmail.com [Cryogenic Engineering Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India); Ghosh, Parthasarathi; Chowdhury, Kanchan [Cryogenic Engineering Centre, Indian Institute of Technology, Kharagpur, West Bengal 721302 (India)

2011-06-15

Large scale helium liquefaction/refrigeration plant is a key subsystem of fusion devices. Performance of these plants is dependent on a number of geometric and operating parameters of its constituting components such as compressors, heat exchangers, expanders, valves, etc. Expander has been chosen as the subject matter of analyses in the present study. As the sensible cold of helium vapor is lost in liquefiers, the expanders in liquefaction cycles have to provide more refrigeration than those in refrigeration cycles. The expander parameters such as rate of mass flow, operating pressure, inlet temperature, etc. are inter-dependent, and hence, it is difficult to predict the system behavior with variation of a particular parameter. This necessitates the use of process simulators. Parametric studies have been performed on Collins helium liquefaction cycle using Aspen HYSYS. Collins cycle has all the basic characteristics of a large-scale helium liquefier and the results of this study may be extrapolated to understand the behavior of large scale helium liquefiers. The study shows that the maximum liquid production is obtained when 80% of the compressor flow is diverted through the expanders and it is equally distributed between the two expanders. The relationships between the liquid production and the isentropic efficiency of expanders are almost linear and both the higher and lower temperature expanders exhibit similar trends.

Conceptual study of hydrogen donor solvent in the NEDOL coal liquefaction process

Energy Technology Data Exchange (ETDEWEB)

Kouzu, M.; Onozaki, M.; Oi, S. [Mitsui SRC Co Ltd, Tokyo (Japan)

2002-03-01

A 150 ton/day coal liquefaction pilot plant (PP) of the NEDOL process, supported by New Energy and Industrial Technology Development Organization (NEDO), was operated successfully for a total of 269 days at Kashima, Japan. With a great number of data obtained through the operation, the design procedure for the NEDOL process was studied. Middle and heavy oils from the coal employed were recycled as a hydrogen-donor solvent after hydrotreatment over Ni Mo/gamma-Al2O{sub 3} in a trickle bed reactor. The hydrogen donating ability of the solvent was high enough to obtain higher oil yield (50-58 wt%) at the aromaticity of ca. 0.45. Life expectancy of solvent hydrotreatment catalyst, requisite to the hydrotreater design, was estimated under PP operating conditions. In addition, physical properties of the solvent required for process design were determined, and hydrodynamics in the liquefaction bubble column reactors were examined. Taking the obtained hydrodynamics and thermal behavior into consideration, a design procedure of the liquefaction bubble column reactors was establsihed using a process simulator (CARD) validated by the product yields of PP. The simulation including distillation and solvent hydrotreatment showed that the content of heavy oil fraction (b.p. 350 - 538{degree} C) in the solvent was a determinant factor in the design of a large scale plant based on the NEDOL process.

Effects of sodium carbonate pretreatment on the chemical compositions and enzymatic saccharification of rice straw.

Science.gov (United States)

Yang, Linfeng; Cao, Jie; Jin, Yongcan; Chang, Hou-min; Jameel, Hasan; Phillips, Richard; Li, Zhongzheng

2012-11-01

The effects of sodium carbonate (Na(2)CO(3)) pretreatment on the chemical compositions and enzymatic saccharification of rice straw were investigated. The enzymatic digestibility of rice straw is enhanced after pretreatment since pretreated solids show significant delignification with high sugar availability. During pretreatment, an increasing temperature and Na(2)CO(3) charge leads to enhanced delignification, whereas an increased degradation of polysaccharides as well, of which xylan acts more susceptible than glucan. The sugar recovery of enzymatic hydrolysis goes up rapidly with the total titratable alkali (TTA) increasing from 0% to 8%, and then it reaches a plateau. The highest sugar recovery of rice straw after pretreatment, 71.7%, 73.2%, and 76.1% for total sugar, glucan, and xylan, respectively, is obtained at 140°C, TTA 8% and cellulase loading of 20 FPU/g-cellulose. In this condition, the corresponding delignification ratio of pretreated solid is 41.8%, while 95% of glucan and 76% of xylan are conserved. Copyright © 2012 Elsevier Ltd. All rights reserved.

Reports on 1976 result of Sunshine Project. Investigation on development policy and position of various coal liquefaction processes in Japan; 1976 nendo Nippon ni okeru kakushu sekitan ekika process no kaihatsu hoshin to ichizuke ni kansuru chosa seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1977-03-01

This report is the summary of the 'investigation results concerning development policy and position of various coal liquefaction processes in Japan'. The purpose of this investigative research is primarily to clarify the position of coal energy in the future energy supply, technologies of converting coal to clean fuel as the form of coal energy utilization most suitable for Japan, and the position of coal liquefaction in such converting technologies, and also to decide on the policy of R and D on coal liquefaction process in Japan at present. Accordingly, this paper investigates the status quo of various liquefaction processes including the coal liquefaction technologies for which R and D are conducted under the Sunshine Project; making analysis/assessment from such viewpoint as clean process as environmental safeguard and a precondition for coal energy utilization, technical problems concerning coal import and transportation, and suitability for the present energy consumption structure centering on oil; and further, examining the position of coal liquefaction in the general effective utilization of coal as organic carbonaceous resources in the distant future. (NEDO)

STUDY OF SOLVENT AND CATALYST INTERACTIONS IN DIRECT COAL LIQUEFACTION; SEMIANNUAL

International Nuclear Information System (INIS)

Michael T. Klein

2000-01-01

There are several aspects of the Direct Coal Liquefaction process which are not fully understood and which if better understood might lead to improved yields and conversions. Among these questions are the roles of the catalyst and the solvent. While the solvent is known to act by transfer of hydrogen atoms to the free radicals formed by thermal breakdown of the coal in an uncatalyzed system, in the presence of a solid catalyst as is now currently practiced, the yields and conversions are higher than in an uncatalyzed system. The role of the catalyst in this case is not completely understood. DOE has funded many projects to produce ultrafine and more active catalysts in the expectation that better contact between catalyst and coal might result. This approach has met with limited success probably because mass transfer between two solids in a fluid medium i.e. the catalyst and the coal, is very poor. It is to develop an understanding of the role of the catalyst and solvent in Direct Liquefaction that this project was initiated. Specifically it was of interest to know whether direct contact between the coal and the catalyst was important. By separating the solid catalyst in a stainless steel basket permeable to the solvent but not the coal in the liquefaction reactor, it was shown that the catalyst still maintains a catalytic effect on the liquefaction process. There is apparently transfer of hydrogen atoms from the catalyst through the basket wall to the coal via the solvent. Strong hydrogen donor solvents appear to be more effective in this respect than weak hydrogen donors. It therefore appears that intimate contact between catalyst and coal is not a requirement, and that the role of the catalyst may be to restore the hydrogen donor strength to the solvent as the reaction proceeds. A range of solvents of varying hydrogen donor strength was investigated. Because of the extensive use of thermogravimetric analysis in this laboratory in was noted that the peak

Comparative Effects of Biomass Pre-Treatments for Direct and Indirect Transesterification to Enhance Microalgal Lipid Recovery

International Nuclear Information System (INIS)

Ghasemi Naghdi, Forough; Thomas-Hall, Skye R.; Durairatnam, Reuben; Pratt, Steven; Schenk, Peer M.

2014-01-01

Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME) recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however, FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane–ethanol (3:1). Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171%) under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min) in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Comparative effects of biomass pre-treatments for direct and indirect transesterification to enhance microalgal lipid recovery

Directory of Open Access Journals (Sweden)

Forough eGhasemi Naghdi

2014-12-01

Full Text Available Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane-ethanol (3:1. Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171% under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Comparative Effects of Biomass Pre-Treatments for Direct and Indirect Transesterification to Enhance Microalgal Lipid Recovery

Energy Technology Data Exchange (ETDEWEB)

Ghasemi Naghdi, Forough; Thomas-Hall, Skye R.; Durairatnam, Reuben [Algae Biotechnology Laboratory, School of Agriculture and Food Sciences, The University of Queensland, Brisbane, QLD (Australia); Pratt, Steven [School of Chemical Engineering, The University of Queensland, Brisbane, QLD (Australia); Schenk, Peer M., E-mail: p.schenk@uq.edu.au [Algae Biotechnology Laboratory, School of Agriculture and Food Sciences, The University of Queensland, Brisbane, QLD (Australia)

2014-12-04

Microalgal lipid recovery for biodiesel production is currently considered suboptimal, but pre-treatment of algal biomass, the use of solvent mixtures and the positioning of transesterification can lead to increased yields. Here, the effect of various reportedly successful pre-treatments and solvent mixtures were directly compared to each other and combined with direct and indirect transesterification methods using the oleaginous microalga Tetraselmis sp. M8. Microwave and thermal pre-treatments were applied and the total lipid and fatty acid methyl ester (FAME) recoveries were investigated. The application of pre-treatments increased FAME recovery through indirect transesterification when a Soxhlet system was used but they had no significant effect for direct transesterification. Gravimetric analyses of total lipids revealed that lipid recovery was highest when utilizing the chloroform-based Bligh and Dyer extraction method; however, FAME yield was the highest when applying a Soxhlet system utilizing a solvent mixture of hexane–ethanol (3:1). Total lipid recovery did not necessarily correlate with the recovery of FAMEs. The highest FAME recovery was achieved from thermal or microwave pre-treated biomass followed by indirect transesterification through Soxhlet extraction. FAME recovery could be more than doubled (increase of up to 171%) under these conditions. We conclude that a simple thermal pre-treatment (80°C for 10 min) in combination with solvent mixture extraction through indirect transesterification may present a cost-effective and scalable option for large-scale lipid extraction from microalgae.

Electrochemical pretreatment of waste activated sludge: effect of process conditions on sludge disintegration degree and methane production.

Science.gov (United States)

Ye, Caihong; Yuan, Haiping; Dai, Xiaohu; Lou, Ziyang; Zhu, Nanwen

2016-11-01

Waste activated sludge (WAS) requires a long digestion time because of a rate-limiting hydrolysis step - the first phase of anaerobic digestion (AD). Pretreatment can be used prior to AD to facilitate the hydrolysis step and improve the efficiency of WAS digestion. This study evaluated a novel application of electrochemical (EC) technology employed as the pretreatment method prior to AD of WAS, focusing on the effect of process conditions on sludge disintegration and subsequent AD process. A superior process condition of EC pretreatment was obtained by reaction time of 30 min, electrolysis voltage of 20 V, and electrode distance of 5 cm, under which the disintegration degree of WAS ranged between 9.02% and 9.72%. In the subsequent batch AD tests, 206 mL/g volatile solid (VS) methane production in EC pretreated sludge was obtained, which was 20.47% higher than that of unpretreated sludge. The AD time was 19 days shorter for EC pretreated sludge compared to the unpretreated sludge. Additionally, the EC + AD reactor achieved 41.84% of VS removal at the end of AD. The analysis of energy consumption showed that EC pretreatment could be effective in enhancing sludge AD with reduced energy consumption when compared to other pretreatment methods.

Producing Lignin-Based Polyols through Microwave-Assisted Liquefaction for Rigid Polyurethane Foam Production

Directory of Open Access Journals (Sweden)

Bai-Liang Xue

2015-02-01

Full Text Available Lignin-based polyols were synthesized through microwave-assisted liquefaction under different microwave heating times (5–30 min. The liquefaction reactions were carried out using polyethylene glycol (PEG-400/glycerol as liquefying solvents and 97 wt% sulfur acid as a catalyst at 140 °C. The polyols obtained were analyzed for their yield, composition and structural characteristics using gel permeation chromatography (GPC, Fourier transform infrared (FT-IR and nuclear magnetic resonance (NMR spectra. FT-IR and NMR spectra showed that the liquefying solvents reacted with the phenol hydroxyl groups of the lignin in the liquefied product. With increasing microwave heating time, the viscosity of polyols was slightly increased and their corresponding molecular weight (MW was gradually reduced. The optimal condition at the microwave heating time (5 min ensured a high liquefaction yield (97.47% and polyol with a suitable hydroxyl number (8.628 mmol/g. Polyurethane (PU foams were prepared by polyols and methylene diphenylene diisocyanate (MDI using the one-shot method. With the isocyanate/hydroxyl group ([NCO]/[OH] ratio increasing from 0.6 to 1.0, their mechanical properties were gradually increased. This study provided some insight into the microwave-assisted liquefied lignin polyols for the production of rigid PU foam.

Reducing biomass recalcitrance via mild sodium carbonate pretreatment.

Science.gov (United States)

Mirmohamadsadeghi, Safoora; Chen, Zhu; Wan, Caixia

2016-06-01

This study examined the effects of mild sodium carbonate (Na2CO3) pretreatment on enzymatic hydrolysis of different feedstocks (i.e., corn stover, Miscanthus, and switchgrass). The results showed that sodium carbonate pretreatment markedly enhanced the sugar yields of the tested biomass feedstocks. The pretreated corn stover, Miscanthus, and switchgrass gave the glucose yields of 95.1%, 62.3%, and 81.3%, respectively, after enzymatic hydrolysis. The above glucose yields of pretreated feedstocks were 2-4 times that of untreated ones. The pretreatment also enhanced the xylose yields, 4 times for corn stover and 20 times for both Miscanthus and switchgrass. Sodium carbonate pretreatment removed 40-59% lignin from the tested feedstocks while preserving most of cellulose (sodium carbonate pretreatment was effective for reducing biomass recalcitrance and subsequently improving the digestibility of lignocellulosic biomass. Copyright © 2016 Elsevier Ltd. All rights reserved.

Process for the liquefaction of solid carbonaceous materials wherein nitrogen is separated from hydrogen via ammonia synthesis

Science.gov (United States)

Stetka, Steven S.; Nazario, Francisco N.

1982-01-01

In a process for the liquefaction of solid carbonaceous materials wherein bottoms residues are upgraded with a process wherein air is employed, the improvement wherein nitrogen buildup in the system is avoided by ammonia synthesis. In a preferred embodiment hydrogen from other portions of the liquefaction process will be combined with hydrogen produced as a result of the bottoms upgrading to increase the H.sub.2 :N.sub.2 ratio in the ammonia reactor.

A characterization and evaluation of coal liquefaction process streams. Quarterly technical progress report, July 1--September 30, 1995

Energy Technology Data Exchange (ETDEWEB)

Robbins, G.A.; Brandes, S.D.; Winschel, R.A.; Burke, F.P.

1995-12-01

The objectives of this project are to support the DOE direct coal liquefaction process development program and to improve the useful application of analytical chemistry to direct coal liquefaction process development. Independent analyses by well-established methods will be obtained of samples produced in direct coal liquefaction processes under evaluation by DOE. Additionally, analytical instruments and techniques which are currently underutilized for the purpose of examining coal-derived samples will be evaluated. The data obtained from this study will be used to help guide current process development and to develop an improved data base on coal and coal liquids properties. A sample bank will be established and maintained for use in this project and will be available for use by other researchers. The reactivity of the non-distillable resids toward hydrocracking at liquefaction conditions (i.e., resid reactivity) will be examined. From the literature and data experimentally obtained, a mathematical kinetic model of resid conversion will be constructed. It is anticipated that such a model will provide insights useful for improving process performance and thus the economics of direct coal liquefaction. Some of the contract activities for this quarter are: We completed many of the analyses on the 81 samples received from HTI bench-scale run CMSL-9, in which coal, coal/mixed plastics, and coal/high density polyethylene were fed; Liquid chromatographic separations of the 15 samples in the University of Delaware sample set were completed; and WRI completed CP/MAS {sup 13}C-NMR analyses on the Delaware sample set.

Report on the FY 1998 results of the New Sunshine Project (B version). Data attached 2. Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo (fuzoku shiryo 2))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the project for internationalization of coal liquefaction technology, this paper reported on the potential survey for location of Indonesian low grade coal liquefaction (study of applicability of the improved BCL process and survey of hydrogen production technology using coal gasification). The survey was conducted of a locational possibility of a coal liquefaction commercial plant to be located at mine site in South Sumatra for Banko coal raw material. The improved BCL process was applied in which the results of the study by NBCL Takasago Research Institute were reflected. Further, the hydrogen production was studied by gasification of Banko coal, and the comparison was made with the conventional natural gas reforming method. As a result of the study using information/knowledge obtained during the conceptual design of Australian brown coal, the construction cost of commercial scale liquefaction plant with the Banko coal processing amount of 30,000 tons/day became 549.8 billion yen in the case of using natural gas as raw material for hydrogen production. This construction cost is the lowest as compared with 601.7 billion yen in the demonstrative BCL process and with 577.1 billion yen in the advanced BCL process. This is a process making use of features of Banko coal. The process for hydrogen production by the steam reforming method using natural gas has an advantage of increasing the production amount of coal-derived liquid the most of the three other methods. (NEDO)

Report on the FY 1998 results of the New Sunshine Project (B version). Data attached 1. Development of coal liquefaction technology (Development of base technology of liquefaction (Project on internationalization of coal liquefaction technology)); 1998 nendo sekitan ekika gijutsu kaihatsu seika hokokusho (B ban). Ekika kiban gijutsu no kaihatsu (sekitan ekika gijutsu no kokusaika jigyo (fuzoku shiryo-1))

Energy Technology Data Exchange (ETDEWEB)

NONE

1999-03-01

As a part of the project for internationalization of coal liquefaction technology, this paper reported on the potential survey for location of Indonesian low grade coal liquefaction (study of applicability of the improved BCL process and survey of hydrogen production technology using coal gasification). The survey was conducted of a locational possibility of a coal liquefaction commercial plant to be located at mine site in South Sumatra for Banko coal raw material. The improved BCL process was applied in which the results of the study by NBCL Takasago Research Institute were reflected. Further, the hydrogen production was studied by gasification of Banko coal, and the comparison was made with the conventional natural gas reforming method. As a result of the study using information/knowledge obtained during the conceptual design of Australian brown coal, the construction cost of commercial scale liquefaction plant with the Banko coal processing amount of 30,000 tons/day became 549.8 billion yen in the case of using natural gas as raw material for hydrogen production. This construction cost is the lowest as compared with 601.7 billion yen in the demonstrative BCL process and with 577.1 billion yen in the advanced BCL process. This is a process making use of features of Banko coal. The process for hydrogen production by the steam reforming method using natural gas has an advantage of increasing the production amount of coal-derived liquid the most of the three other methods. (NEDO)

Effects of chemical-physical pre-treatment processes on hemp fibres for reinforcement of composites and textiles

DEFF Research Database (Denmark)

Thomsen, Anne Belinda; Thygesen, Anders; Bohn, Vibeke

2006-01-01

Retted hemp fibres were treated using chemical-physical pre-treatments and the material was characterised chemically in order to evaluate the effect of the pre-treatments, respectively, wet oxidation (WO), hydrothermal treatment (HT) and steam explosion (STEX). Process variables were addition...

Effects of process parameters of various pretreatments on enzymatic hydrolysability of Ceiba pentandra (L.) Gaertn. (Kapok) fibre: A response surface methodology study

International Nuclear Information System (INIS)

Tye, Ying Ying; Lee, Keat Teong; Wan Abdullah, Wan Nadiah; Leh, Cheu Peng

2015-01-01

Kapok fibre is a promising raw material to produce sugar by enzymatic hydrolysis. In this work, effects of water, acid and alkaline pretreatments on the enzymatic sugar yield were studied through response surface methodology (RSM) and supported by the analysis of chemical compositions and physical structure of the fibre. For water pretreatment, reaction temperature and time were the independent variables while chemical concentration was also used as the third independent variable for acid and alkaline pretreatments. For all pretreatments, the enzymatic hydrolysis conditions were kept constant. The structure of pretreated fibre was also examined using scanning electron microscope (SEM). Results showed that water and acid pretreatments effectively dissolved hemicellulose of the fibre with the latter unveiled better results. The alkaline pretreatment resulted in the highest total glucose yield (g/kg of untreated fibre) as compared to water and acid pretreatments. SEM analysis illustrated that water and acid pretreatments led severe destruction of fibre structure; however, both of these pretreatments exhibited lower enhancement of enzymatic hydrolysability of kapok fibre as compared to that observed in alkaline pretreatment. - Highlights: • Effect of pretreatments on sugar yield was studied by response surface methodology. • Glucose yield was highly related to the chemical compositions of pretreated fibers. • Pretreatments altered the physical structure of kapok fibers. • Enzymatic hydrolysability of fibre was improved the most by alkaline treatment. • Over 94% cellulose of the pretreated fibres was converted to glucose

Helium refrigeration system for hydrogen liquefaction applications

Science.gov (United States)

Nair, J. Kumar, Sr.; Menon, RS; Goyal, M.; Ansari, NA; Chakravarty, A.; Joemon, V.

2017-02-01

Liquid hydrogen around 20 K is used as cold moderator for generating “cold neutron beam” in nuclear research reactors. A cryogenic helium refrigeration system is the core upon which such hydrogen liquefaction applications are built. A thermodynamic process based on reversed Brayton cycle with two stage expansion using high speed cryogenic turboexpanders (TEX) along with a pair of compact high effectiveness process heat exchangers (HX), is well suited for such applications. An existing helium refrigeration system, which had earlier demonstrated a refrigeration capacity of 470 W at around 20 K, is modified based on past operational experiences and newer application requirements. Modifications include addition of a new heat exchanger to simulate cryogenic process load and two other heat exchangers for controlling the temperatures of helium streams leading out to the application system. To incorporate these changes, cryogenic piping inside the cold box is suitably modified. This paper presents process simulation, sizing of new heat exchangers as well as fabrication aspects of the modified cryogenic process piping.

Design and analysis of liquefaction process for offshore associated gas resources

International Nuclear Information System (INIS)

Li, Q.Y.; Ju, Y.L.

2010-01-01

Liquefaction is the key section on floating platform. Some experts and designers selected mixed refrigerant process for floating platform, while some recommended expander cycle. However, few of them compared the two types of processes systemically before making a choice. In this paper, the liquefaction processes of propane pre-cooled mixed refrigerant cycle (C 3 /MRC), mixed refrigerant cycle (MRC) and nitrogen expander cycle (N 2 expander) for the special offshore associated gases in South China Sea have been designed and studied. These processes have been analyzed and compared systematically considering the main factors including the performance parameters, economic performance, layout, sensitivity to motion, suitability to different gas resources, safety and operability, accounting for the features of the floating production, storage and offloading unit for liquefied natural gas (LNG-FPSO) in marine environment. The results indicated that N 2 expander has higher energy consumption and poorer economic performance, while it has much more advantages than C 3 /MRC and MRC for offshore application because it is simpler and more compact and thus requiring less deck area, less sensitive to LNG-FPSO motion, has better suitability for other gas resources, has higher safety and is easier to operate. Therefore, N 2 expander is the most suitable offshore liquefaction process. In addition, the exergy analysis is conducted for N 2 expander and the results indicate that the compression equipments and after coolers, expanders and LNG heat exchangers are the main contribution to the total exergy losses. The measures to decrease the losses for these equipments are then discussed.

Achievement report for fiscal 1993 on research under Sunshine Program. Research on direct liquefaction reaction of coal; 1993 nendo sekitan no chokusetsu ekika hanno ni kansuru kenkyu seika hokokusho

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-03-01

The reaction velocity constant of coal or the distribution of products in a high-pressure hydrocracking process of coal are found not to be affected by the temperature rise rate. The liquefaction of coal using CO and water is analyzed using a high-pressure differential thermal analyzer. The hydrogen gas generated during the water gas reaction reacts with CO for the formation of alcohols, carbonic acid, etc. The reaction rate is found to be higher when the specimen contains more oxygen. When coals greatly different from each other in terms of thermolytic reactivity, caking property, and intersolubility with medium oils are mixed, synergistic effects are exhibited, positive when active hydrogen supply is abundant and negative when it is short. In the case of the Hokkaido coal which contains 73.0-87.4% carbon, the grain diameter does not affect the liquefaction rate when the coal is crushed to the 48-mesh size approximately. Reaction velocity in direct liquefaction does not relate to hydrogen pressure. Asphaltenes in coal liquefaction are produced at the beginning of reaction, to be reduced in molecular weight due to cleavage of methylene crosslinks with the progress of reaction. Studies are conducted in a 0.1t/d-capable bench plant about liquefaction reaction characteristics and coal liquid properties, and chemical structures. (NEDO)

Catalytic hydrothermal liquefaction (HTL of biomass for bio-crude production using Ni/HZSM-5 catalysts

Directory of Open Access Journals (Sweden)

Shouyun Cheng

2017-04-01

Full Text Available Hydrothermal liquefaction (HTL is an effective method that can convert biomass into bio-crude, but direct use of bio-crude derived from biomass HTL remains a challenge due to the lower quality. In this study, bifunctional Ni/HZSM-5 catalysts and zinc hydrolysis were combined to produce upgraded bio-crude in an in-situ HTL process. The K2CO3 and HZSM-5 catalysts with different Ni loading ratios were tested. The effects of different catalysts on the yield and quality of bio-crude and gas were investigated. The results indicated that the catalysts improved bio-crude and gas yields, compared to pine sawdust liquefaction without catalyst. The catalysts reduced the contents of undesirable oxygenated compounds such as acids, ketones, phenols, alcohols and esters in bio-crude products while increased desirable hydrocarbons content. K2CO3 produced highest bio-crude yield and lowest solid residue yield among all catalysts. Compared to parent HZSM-5 catalyst, bifunctional Ni/HZSM-5 catalysts exhibited higher catalyst activity to improve quality of upgraded bio-crude due to its integration of cracking and hydrodeoxygenation reactions. 6%Ni/HZSM-5 catalyst produced the bio-crude with the highest hydrocarbons content at 11.02%. This catalyst can be a candidate for bio-crude production from biomass HTL.

Assessment and mitigation of liquefaction

International Nuclear Information System (INIS)

Czelada, J. A.; Melentijevic, S.

2014-01-01

The simplified empirical procedure in its original form presented in Youd et al (2001) and some further developments given in Idriss and Boulanger (2006) for evaluating liquefaction resistance of soils is presented in this paper only for the criteria based on standard penetration test (SPT). Methods for estimating the ground improvement techniques by stone columns and dynamics compaction are presented. For stone columns Priebe method (1995) and homogenized method (equivalent parameters) are present. for dynamic compaction methods proposed by Recomendacion Geotecnica para las Obras Maritimas y/o Porturaria - ROM 0.5-05 (2005) and Nashed et al. (2009) are described. These analysis methods for each ground improvement technique are compared in two different case histories showing similar results in each one. (Author)

Feasibility and comparative studies of thermochemical liquefaction of Camellia oleifera cake in different supercritical organic solvents for producing bio-oil

International Nuclear Information System (INIS)

Chen, Hongmei; Zhai, Yunbo; Xu, Bibo; Xiang, Bobin; Zhu, Lu; Li, Ping; Liu, Xiaoting; Li, Caiting; Zeng, Guangming

2015-01-01

Highlights: • Thermochemical liquefaction of COC was a prominent process for producing bio-oil. • Type of solvent affected the yield and composition of bio-oil considerably. • Liquefaction of COC in SCEL at 300 °C was preferred for producing bio-oil. - Abstract: Thermochemical liquefaction of Camellia oleifera cake (COC) for producing bio-oil was conducted in supercritical methanol (SCML), ethanol (SCEL) and acetone (SCAL), respectively. GC–MS, elemental analysis and ICP-OES were used to characterize properties of bio-oil. Results showed that thermochemical liquefaction of COC was a prominent process for generating bio-oil. Increase of temperature was beneficial to the increase of bio-oil yield, and yield of bio-oil followed the sequence of SCAL > SCEL > SCML. In spite of the highest bio-oil yield, the lowest calorific value and highest contents of Zn, Pb, Cd, Ni, Fe, Mn, and Cr were found in bio-oil from SCAL. Though SCML has very similar bio-oil composition and calorific value with SCEL, higher bio-oil yield and lower contents of heavy metals could be obtained with SCEL, especially in bio-oil from SCEL at 300 °C. Moreover, the origin of ethanol could make the bio-oil product totally renewable. Therefore, liquefaction of COC in SCEL at 300 °C could have great potential in generating bio-oil

Effects of Pretreatment of Single and Mixed Lignocellulosic Substrates on Production of Endoglucanase by Bacillus aerius S5.2

Directory of Open Access Journals (Sweden)

Mushafau Adebayo Oke

2016-06-01

Full Text Available A mixed substrate (MS comprising oil palm empty fruit bunch (EFB, oil palm frond (OPF, and rice husk (RH was evaluated for endoglucanase production by Bacillus aerius S5.2. Effects of sulphuric acid, sodium hydroxide, N-methylmorpholine-N-oxide (NMMO, and hydrothermal pretreatments on endoglucanase production were investigated. Endoglucanase production by B. aerius on the untreated (0.677 U/mL and pretreated MS (0.305 – 0.630 U/mL was generally similar, except that the acid (0.305 U/mL and hydrothermal (0.549 U/mL pretreatments that were more severe consequently produced significantly lower titres. Alkali pretreatment supported the highest enzyme production (0.630 U/mL among all pretreatments that were studied. When endoglucanase production on the alkali-pretreated MS and single substrates (SS was compared, alkali-pretreated EFB produced a titre (0.655 U/mL similar to the MS, and this was significantly higher than titres recorded on OPF (0.504 U/mL and RH (0.525 U/mL. Lower enzyme production was found to be consistent with higher pretreatment severity and greater removal of amorphous regions in all the pretreatments. Furthermore, combining the SS showed no adverse effects on endoglucanase production.

Developing Effective Separation of Feldspar and Quartz While Recycling Tailwater by HF Pretreatment

Directory of Open Access Journals (Sweden)

Weiqing Wang

2018-04-01

Full Text Available The effect of hydrofluoric acid (HF pretreatment on flotation of feldspar and quartz using dodecylamine (DDA as collector was investigated by micro-flotation, zeta potential, pyrene fluorescence spectroscopy, attenuated total reflection flourier transformed infrared spectroscopy (ATR-FTIR, scanning electron microscope (SEM, X-ray photoelectron spectroscopy (XPS and bench scale flotation. The micro-flotation tests revealed that there was little difference in the flotation of feldspar and quartz at pH 2, using H2SO4 as pH regulator. After HF pretreatment, the floatability of feldspar significantly increased while the floatability of quartz showed no change. HF pretreatment resulted in leaching of SiO2 and enrichment of Na, K and Al on the feldspar surface. Consequently, the negative surface charge of feldspar increased at pH 2, which allowed for the flotation separation of the feasible minerals. This took place via an increased electrostatic adsorption between DDA and Na, K, Al on the feldspar surface, which effectively increased its hydrophobicity and as a result, improved the floatability of feldspar. An alternative process which exhibited effective separation of quartz and feldspar while recycling the tailwater from the flotation was proposed.

Effect of the pre-treatment on the performance of MBR, Berghausen WWTP. Germany

Directory of Open Access Journals (Sweden)

Medhat A.E. Moustafa

2011-06-01

Full Text Available Pilot scale experiments were carried out to examine the effect of the pre-treatment methods on the performance of MBR. The PURON® MBR module was used in this study. In order to investigate the effect of pre-treatment on the behaviour of membrane, samples were withdrawn at different locations in Berghausen WWTP. During the first period samples have been collected directly from the main source as raw sewage to determine its main characteristics. During the second period samples have been screened with screening 1 mm filter material to prevent debris from damaging the membrane. During the third phase samples have been taken after the primary settling tank to have the benefits of filtering out unwanted trash, removing scum and floating debris. The study showed that the membrane bio-reactor filters out nearly all solids, the pre-treatment has a positive effect on the MBR performance, and the pre-sedimentation is more effective than fine screening. Moreover, aeration is considered as one of the intrinsic parameters in both hydraulic and biological process performances because of its ability to maintain solids in suspension, scours the membrane surface, limits fouling, and provide oxygen to the biomass, which results in a better biodegradability.

Advanced Direct Liquefaction Concepts for PETC Generic Units - Phase II

Energy Technology Data Exchange (ETDEWEB)

None

1997-12-01

The results of Laboratory and Bench-Scale experiments and supporting technical and economic assessments conducted under DOE Contract No. DE-AC22-91PC91040 are reported for the period July 1, 1997 to September 30, 1997. This contract is with the University of Kentucky Research Foundation which supports work with the University of Kentucky Center for Applied Energy Research, CONSOL, Inc., LDP Associates, and Hydrocarbon Technologies, Inc. This work involves the introduction into the basic two stage liquefaction process several novel concepts which include dispersed lower-cost catalysts, coal cleaning by oil agglomeration, and distillate hydrotreating and dewaxing. Results are reported from experiments in which various methods were tested to activate dispersed Mo precursors. Several oxothiomolybdates precursors having S/Mo ratios from two to six were prepared. Another having a S/Mo ratio of eleven was also prepared that contained an excess of sulfur. In the catalyst screening test, none of these precursors exhibited an activity enhancement that might suggest that adding sulfur into the structure of the Mo precursors would be beneficial to the process. In another series of experiments, AHM impregnated coal slurried in the reaction mixture was pretreated withH S/H under pressure and successively heated for 30 min at 120, 250 2 2 and 360 C. THF conversions in the catalyst screening test were not affected while resid conversions o increased such that pretreated coals impregnated with 100 ppm Mo gave conversions equivalent to untreated coals impregnated with 300 ppm fresh Mo. Cobalt, nickel and potassium phosphomolybdates were prepared and tested as bimetallic precursors. The thermal stability of these compounds was evaluated in TG/MS to determine whether the presence of the added metal would stabilize the Keggin structure at reaction temperature. Coals impregnated with these salts showed the Ni and Co salts gave the same THF conversion as PMA while the Ni salt gave higher

Role of heat exchangers in helium liquefaction cycles: Simulation studies using Collins cycle

Energy Technology Data Exchange (ETDEWEB)

Thomas, Rijo Jacob, E-mail: rijojthomas@gmail.com [Cryogenic Engineering Centre, Indian Institute of Technology, Kharagpur 721302 (India); Ghosh, Parthasarathi; Chowdhury, Kanchan [Cryogenic Engineering Centre, Indian Institute of Technology, Kharagpur 721302 (India)

2012-01-15

Highlights: Black-Right-Pointing-Pointer Role of heat exchangers in basic helium liquefier analyzed to design large-scale ones. Black-Right-Pointing-Pointer Heat exchangers that determine inlet temperature to expanders are more significant. Black-Right-Pointing-Pointer Limiting values of nondimensional UA for each heat exchanger have been determined. Black-Right-Pointing-Pointer Extra area distributed such that effectiveness of all heat exchangers increase uniformly. Black-Right-Pointing-Pointer Heat exchanger performance variation have little influence on the optimum expander flow. - Abstract: Energy efficiency of large-scale helium liquefiers generally employed in fusion reactors and accelerators is determined by the performance of their constituting components. Simulation with Aspen HYSYS{sup Registered-Sign} V7.0, a commercial process simulator, helps to understand the effects of heat exchanger parameters on the performance of a helium liquefier. Effective UA (product of overall heat transfer coefficient U, heat transfer surface area A and deterioration factor F) has been taken as an independent parameter, which takes into account all thermal irreversibilities and configuration effects. Nondimensionalization of parameters makes the results applicable to plants of any capacity. Rate of liquefaction is found to increase linearly with the effectiveness of heat exchangers. Performance of those heat exchangers that determine the inlet temperatures to expanders have more influence on the liquid production. Variation of sizes of heat exchangers does not affect the optimum rate of flow through expanders. Increasing UA improves the rate of liquid production; however, the improvement saturates at limiting UA. Maximum benefit in liquefaction is obtained when the available heat transfer surface area is distributed in such a way that the effectiveness remains equal for all heat exchangers. Conclusions from this study may be utilized in analyzing and designing large helium

The current status of coal liquefaction technologies - Panorama 2008; La liquefaction du charbon: ou en est-on aujourd'hui? - Panorama 2008

Energy Technology Data Exchange (ETDEWEB)

NONE

2008-07-01

In 2008, a first coal liquefaction unit to produce motor fuel (20,000 BPSD) will come on-stream in Shenhua, China (in the Ercos region of Inner Mongolia). Other, more ambitious projects have been announced in China for between now and 2020. Since oil production is expected to peak in the medium term, this technology may develop regionally in the next 20 years to cover ever-increasing demand for motor fuel.

New magnetic refrigeration materials for the liquefaction of hydrogen

International Nuclear Information System (INIS)

Gschneidner, K.A.; Takeya, H.; Moorman, J.O.; Pecharsky, V.K.; Malik, S.K.; Zimm, C.B.

1994-01-01

Five heavy lanthanide ferromagnetic intermetallic compounds were studied as potential magnetic refrigerants for the liquefaction of hydrogen gas. (Dy 0.5 Er 0.5 )Al 2 and TbNi 2 appear to be better refrigerants than GdPd for a Joule-Brayton cycle refrigerator, while (Gd 0.54 Er 0.46 )AlNi seems to be a suitable refrigerant for an Ericsson cycle refrigerator

Modelling landslide liquefaction, mobility bifurcation and the dynamics of the 2014 Oso disaster

Science.gov (United States)

Iverson, Richard M.; George, David L.

2016-01-01

Some landslides move slowly or intermittently downslope, but others liquefy during the early stages of motion, leading to runaway acceleration and high-speed runout across low-relief terrain. Mechanisms responsible for this disparate behaviour are represented in a two-phase, depth-integrated, landslide dynamics model that melds principles from soil mechanics, granular mechanics and fluid mechanics. The model assumes that gradually increasing pore-water pressure causes slope failure to nucleate at the weakest point on a basal slip surface in a statically balanced mass. Failure then spreads to adjacent regions as a result of momentum exchange. Liquefaction is contingent on pore-pressure feedback that depends on the initial soil state. The importance of this feedback is illustrated by using the model to study the dynamics of a disastrous landslide that occurred near Oso, Washington, USA, on 22 March 2014. Alternative simulations of the event reveal the pronounced effects of a landslide mobility bifurcation that occurs if the initial void ratio of water-saturated soil equals the lithostatic, critical-state void ratio. They also show that the tendency for bifurcation increases as the soil permeability decreases. The bifurcation implies that it can be difficult to discriminate conditions that favour slow landsliding from those that favour liquefaction and long runout.

Effects of phenobarbital pretreatment on the in vivo metabolism of carbaryl in rats