WorldWideScience

Sample records for east foundry cove

  1. Declining metal levels at Foundry Cove (Hudson River, New York): Response to localized dredging of contaminated sediments

    International Nuclear Information System (INIS)

    Mackie, Joshua A.; Natali, Susan M.; Levinton, Jeffrey S.; Sanudo-Wilhelmy, Sergio A.

    2007-01-01

    This study examines the effectiveness of remediating a well-recognized case of heavy metal pollution at Foundry Cove (FC), Hudson River, New York. This tidal freshwater marsh was polluted with battery-factory wastes (1953-1979) and dredged in 1994-1995. Eight years after remediation, dissolved and particulate metals (Cd, Co, Cu, Pb, Ni, and Ag) were found to be lower than levels in the lower Hudson near New York City. Levels of metals (Co, Ni, Cd) on suspended particles were comparatively high. Concentrations of surface sediment Cd throughout the marsh system remain high, but have decreased both in the dredged and undredged areas: Cd was 2.4-230 mg/kg dw of sediment in 2005 vs. 109-1500 mg/kg in the same area in 1983. The rate of tidal export of Cd from FC has decreased by >300-fold, suggesting that dredging successfully stemmed a major source of Cd to the Hudson River. - Dredging of a hotspot of metal-contaminated sediment is associated with a recognizable local and river-wide decline in cadmium in the Hudson River, New York

  2. Molecular Foundry

    Science.gov (United States)

    . New Study Indicates Greater Capacity for Carbon Storage in the Earth's Subsurface A team of Foundry minerals which make up the dominant clays in the Earth's deep subsurface. Doubling Down on Energy Storage identify molecular components within small volumes of biological samples, such as blood or urine. Industry

  3. The Molecular Foundry (TMF)

    Data.gov (United States)

    Federal Laboratory Consortium — Founded in 2006 by the Department of Energy (DOE), the Molecular Foundry is a critical part of the DOE's National Nanotechnology Initiative, a multi-agency framework...

  4. Energy conservation in foundry

    International Nuclear Information System (INIS)

    Natu, V.M.

    1994-01-01

    In any foundry, the cost of fuel in the form of coal, oil or electrical power, is about 10 to 15% of the cost of the product. Saving of the order of 30 to 50% can be achieved in energy by reducing consumption of fuel and increasing efficiency. This has been illustrated by describing 4 examples in foundry industry. In each case, saving in terms of rupees is also indicated. (N.B.)

  5. FOUNDRY WASTE MANAGEMENT

    Directory of Open Access Journals (Sweden)

    Borut Kosec

    2008-06-01

    Full Text Available Waste management in foundries is gaining a higher ecological and economical importance. Waste is becoming an increasingly traded product, where excellent profits can be made. Due to the cost reduction and successful business operation in companies, waste has to be regenerated and used again as a material to the maximum possible extent. Such research is long lasting and expensive and is a great challenge for companies. In the frame of our research, a total waste management case study for the Slovenian foundry Feniks was carried out. From the sustainable development point of view, waste management is most suitable, since it ensures the material utilization of waste, reduces the consumption of natural renewable or non-renewable resources and makes efficient production capacity utilization possible. Properly treated ecologically safe waste with a suitable physical characteristic, long-term existence, is a substitute for natural materials. Sand, dust, slag and other mineral waste from foundries are increasingly being used as materials in other industries. The foundry Feniks was awarded with certification of the environmental management system according to the standard SIST EN ISO 14001 and confirmed its environmental credentials.

  6. The restoration of an Argonne National Laboratory foundry

    International Nuclear Information System (INIS)

    Shearer, T.; Pancake, D.; Shelton, B.

    1997-01-01

    The Environmental Management Operations' Waste Management Department (WMD) at Argonne National Laboratory-East (ANL-E) undertook the restoration of an unused foundry with the goal of restoring the area for general use. The foundry was used in the fabrication of reactor components for ANL's research and development programs; many of the items fabricated in the facility were radioactive, thereby contaminating the foundry equipment. This paper very briefly describes the dismantling and decontamination of the facility. The major challenges associated with the safe removal of the foundry equipment included the sheer size of the equipment, a limited overhead crane capability (4.5 tonne), the minimization of radioactive and hazardous wastes, and the cost-effective completion of the project, the hazardous and radioactive wastes present, and limited process knowledge (the facility was unused for many years)

  7. JPL Innovation Foundry

    Science.gov (United States)

    Sherwood, Brent; McCleese, Daniel

    2012-01-01

    Space science missions are increasingly challenged today: in ambition, by increasingly sophisticated hypotheses tested; in development, by the increasing complexity of advanced technologies; in budgeting, by the decline of flagship-class mission opportunities; in management, by expectations for breakthrough science despite a risk-averse programmatic climate; and in planning, by increasing competition for scarce resources. How are the space-science missions of tomorrow being formulated? The paper describes the JPL Innovation Foundry, created in 2011, to respond to this evolving context. The Foundry integrates methods, tools, and experts that span the mission concept lifecycle. Grounded in JPL's heritage of missions, flight instruments, mission proposals, and concept innovation, the Foundry seeks to provide continuity of support and cost-effective, on-call access to the right domain experts at the right time, as science definition teams and Principal Investigators mature mission ideas from "cocktail napkin" to PDR. The Foundry blends JPL capabilities in proposal development and concurrent engineering, including Team X, with new approaches for open-ended concept exploration in earlier, cost-constrained phases, and with ongoing research and technology projects. It applies complexity and cost models, projectformulation lessons learned, and strategy analyses appropriate to each level of concept maturity. The Foundry is organizationally integrated with JPL formulation program offices; staffed by JPL's line organizations for engineering, science, and costing; and overseen by senior Laboratory leaders to assure experienced coordination and review. Incubation of each concept is tailored depending on its maturity and proposal history, and its highest leverage modeling and analysis needs.

  8. JPL Innovation Foundry

    Science.gov (United States)

    Sherwood, Brent; McCleese, Daniel

    2013-08-01

    Space science missions are increasingly challenged today: in ambition, by increasingly sophisticated hypotheses tested; in development, by the increasing complexity of advanced technologies; in budgeting, by the decline of flagship-class mission opportunities; in management, by expectations for breakthrough science despite a risk-averse programmatic climate; and in planning, by increasing competition for scarce resources. How are the space-science missions of tomorrow being formulated? The paper describes the JPL Innovation Foundry, created in 2011, to respond to this evolving context. The Foundry integrates methods, tools, and experts that span the mission concept lifecycle. Grounded in JPL's heritage of missions, flight instruments, mission proposals, and concept innovation, the Foundry seeks to provide continuity of support and cost-effective, on-call access to the right domain experts at the right time, as science definition teams and Principal Investigators mature mission ideas from "cocktail napkin" to PDR. The Foundry blends JPL capabilities in proposal development and concurrent engineering, including Team X, with new approaches for open-ended concept exploration in earlier, cost-constrained phases, and with ongoing research and technology projects. It applies complexity and cost models, project-formulation lessons learned, and strategy analyses appropriate to each level of concept maturity. The Foundry is organizationally integrated with JPL formulation program offices; staffed by JPL's line organizations for engineering, science, and costing; and overseen by senior Laboratory leaders to assure experienced coordination and review. Incubation of each concept is tailored depending on its maturity and proposal history, and its highest-leverage modeling and analysis needs.

  9. European MEMS foundries

    Science.gov (United States)

    Salomon, Patric R.

    2003-01-01

    According to the latest release of the NEXUS market study, the market for MEMS or Microsystems Technology (MST) is predicted to grow to $68B by the year 2005, with systems containing these components generating even higher revenues and growth. The latest advances in MST/MEMS technology have enabled the design of a new generation of microsystems that are smaller, cheaper, more reliable, and consume less power. These integrated systems bring together numerous analog/mixed signal microelectronics blocks and MEMS functions on a single chip or on two or more chips assembled within an integrated package. In spite of all these advances in technology and manufacturing, a system manufacturer either faces a substantial up-front R&D investment to create his own infrastructure and expertise, or he can use design and foundry services to get the initial product into the marketplace fast and with an affordable investment. Once he has a viable product, he can still think about his own manufacturing efforts and investments to obtain an optimized high volume manufacturing for the specific product. One of the barriers to successful exploitation of MEMS/MST technology has been the lack of access to industrial foundries capable of producing certified microsystems devices in commercial quantities, including packaging and test. This paper discusses Multi-project wafer (MPW) runs, requirements for foundries and gives some examples of foundry business models. Furthermore, this paper will give an overview on MST/MEMS services that are available in Europe, including pure commercial activities, European project activities (e.g. Europractice), and some academic services.

  10. Excavations at Cook's Cove, Tolaga Bay, New Zealand

    International Nuclear Information System (INIS)

    Walter, R.; Jacomb, C.; Brooks, E.

    2011-01-01

    The Cook's Cove site (Z17/311) on the East Coast of the North Island of New Zealand is an unusual example of an archaeological site spanning close to the full duration of the New Zealand prehistoric sequence. In addition to a record of Polynesian activities, the site is also well known as the type site for the North Island Holocene stratigraphy. Recent excavations at Cook's Cove have resulted in a reinterpretation of the nature of Polynesian occupation and adaptation in this part of the North Island. The application of an 'event phase' interpretative approach provides the means for reconstructing a detailed history of environmental processes and their relationships to cultural activities over a period of 700 years. (author). 61 refs., 17 figs., 13 tabs.

  11. Foundry Coating Technology: A Review

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Tiedje, Niels Skat

    2011-01-01

    is important. In this review, a detailed description of these topics and examples are provided where necessary. A potential area of research in foundry coating development, using sol-gel process is suggested. The application of sol-gel technology in the development of foundry coatings is a novel approach....

  12. Foundries and environmental economy

    Energy Technology Data Exchange (ETDEWEB)

    Caglioti, V

    1974-01-01

    There is a growing emphasis on the recycling of natural resources. For example, the reprocessing of scrap iron involves an average saving of 74% of the energy used in ore reduction and an 84% decrease in pollution output. This calls for an approach to manufacturing that will favor the recycling of raw materials used. A publication of the American Foundrymen's Society lists 450 substances for which there are maximum permissible limits in the foundry work environment. It has been estimated that in Italy, on the average, about 20% of the cost of a manufacturing plant must now be allocated to pollution abatement equipment. Interdisciplinary communication where engineers can converse with physicists, chemists and environmentalists, and vice versa is discussed. Environmentalism also cannot be considered an isolation from the need to regulate the standard of living and to understand and influence human behavior.

  13. JPL Innovation Foundry

    Science.gov (United States)

    Sherwood, Brent; McCleese, Daniel J.

    2012-01-01

    NASA supports the community of mission principal investigators by helping them ideate, mature, and propose concepts for new missions. As NASA's Federally Funded Research and Development Center (FFRDC), JPL is a primary resource for providing this service. The environmental context for the formulation lifecycle evolves continuously. Contemporary trends include: more competitors; more-complex mission ideas; scarcer formulation resources; and higher standards for technical evaluation. Derived requirements for formulation support include: stable, clear, reliable methods tailored for each stage of the formulation lifecycle; on-demand access to standout technical and programmatic subject-matter experts; optimized, outfitted facilities; smart access to learning embodied in a vast oeuvre of prior formulation work; hands-on method coaching. JPL has retooled its provision of integrated formulation lifecycle support to PIs, teams, and program offices in response to this need. This mission formulation enterprise is the JPL Innovation Foundry.

  14. Combinatorial optimization in foundry practice

    Science.gov (United States)

    Antamoshkin, A. N.; Masich, I. S.

    2016-04-01

    The multicriteria mathematical model of foundry production capacity planning is suggested in the paper. The model is produced in terms of pseudo-Boolean optimization theory. Different search optimization methods were used to solve the obtained problem.

  15. SIZE, STRUCTURE AND FUNCTIONALITY IN SHALLOW COVE COMMUNITIES IN RI

    Science.gov (United States)

    We are using an ecosystem approach to examine the ecological integrity and important habitats in small estuarine coves. We sampled the small undeveloped Coggeshall Cove during the sununer of 1999. The cove was sampled at high tide at every 15 cm of substrate elevation along trans...

  16. COVE 2A Benchmarking calculations using NORIA

    International Nuclear Information System (INIS)

    Carrigan, C.R.; Bixler, N.E.; Hopkins, P.L.; Eaton, R.R.

    1991-10-01

    Six steady-state and six transient benchmarking calculations have been performed, using the finite element code NORIA, to simulate one-dimensional infiltration into Yucca Mountain. These calculations were made to support the code verification (COVE 2A) activity for the Yucca Mountain Site Characterization Project. COVE 2A evaluates the usefulness of numerical codes for analyzing the hydrology of the potential Yucca Mountain site. Numerical solutions for all cases were found to be stable. As expected, the difficulties and computer-time requirements associated with obtaining solutions increased with infiltration rate. 10 refs., 128 figs., 5 tabs

  17. Qualitative characteristics of foundry dusts

    Directory of Open Access Journals (Sweden)

    K. Nowacki

    2018-01-01

    Full Text Available Recycling has become a top priority research task in highly developed countries, addressed from the perspective of environmental protection as well as cost-effectiveness of products. In many countries, including Poland, landfilling is still commonly accepted as a method of choice for waste neutralisation. This paper presents results of studies on the environmental impact of iron-bearing foundry waste in the event of its landfill disposal.

  18. Environmental Protection Versus Foundry Engineering Practice

    OpenAIRE

    Maj M.; Werrtz J.; Piekło J.

    2017-01-01

    • Theory and practice of environmental protection in the case of foundries in Europe and Asia • Experience resulting from the cooperation with the foundries in a few European countries, China and India • Phenomena and factors affecting the pollution of the natural environment and the implementation of measures aiming at the environmental protection. Every specialist dealing with foundry processes and their impact on environmental pollution must have encountered in their professional careers n...

  19. Design and Fabrication of a Foundry Sand Mixer Using Locally ...

    African Journals Online (AJOL)

    Most small foundry shops mix their sand manually which is not efficient since homogenous mix cannot be guaranteed and even when foundry mixer are available most of them are imported costing the nation huge foriegn exchange. A foundry sand mixer capable of mixing foundry sand has been designed and fabricated ...

  20. Health and safety at work in foundry companies

    Directory of Open Access Journals (Sweden)

    L. Wojtynek

    2011-07-01

    Full Text Available The article presents the identification and analysis of threats in the environment of the foundry at individual stages of the casts manufacturing process. A generalized model of the foundry was created in the system presentation including harmful and dangerous factors in the foundry technical workplace. This model can refer to an iron foundry and cast steel and small non-ferrous foundries, to modern foundries, with automatic moulding lines and to chill and pressure foundries where machines execute the majority of essential operations.

  1. SEARCH OF COMPOSITIONS OF FOUNDRY GRADES

    Directory of Open Access Journals (Sweden)

    O. S. Komarov

    2014-01-01

    Full Text Available Comparative researches of foundry paints showed that the most acceptable basis for them is disthenesillimanite and it is possible to use sodium aluminate solution as a binding agent.

  2. Environmental Protection Versus Foundry Engineering Practice

    Directory of Open Access Journals (Sweden)

    Maj M.

    2017-06-01

    Full Text Available • Theory and practice of environmental protection in the case of foundries in Europe and Asia • Experience resulting from the cooperation with the foundries in a few European countries, China and India • Phenomena and factors affecting the pollution of the natural environment and the implementation of measures aiming at the environmental protection. Every specialist dealing with foundry processes and their impact on environmental pollution must have encountered in their professional careers numerous situations in which the theory of environmental protection confronts the stark reality. The discrepancy between theory and practice can particularly be noticed in foundry engineering in developing countries where the contrasts between different countries and casting plants are extremely striking. The comparison of working conditions in European and Asian foundries provides a vast scope for further observations and analyses. Environmental protection seems not only a concern of manufacturers of castings, but also of their customers whose opinion exerts a significant influence on both the acceptability of working conditions and on the approach to environmental pollution adopted in metal casting industry. The article presents a number of examples of various outlooks on environmental issues in foundries manufacturing a wide range of cast steel and cast iron castings, where different technologies and production processes are applied.

  3. Half Moon Cove Tidal Project. Feasibility report

    Energy Technology Data Exchange (ETDEWEB)

    1980-11-01

    The proposed Half Moon Cove Tidal Power Project would be located in a small cove in the northern part of Cobscook Bay in the vicinity of Eastport, Maine. The project would be the first tidal electric power generating plant in the United States of America. The basin impounded by the barrier when full will approximate 1.2 square miles. The average tidal range at Eastport is 18.2 feet. The maximum spring tidal range will be 26.2 feet and the neap tidal range 12.8 feet. The project will be of the single pool-type single effect in which generation takes place on the ebb tide only. Utilizing an average mean tidal range of 18.2 feet the mode of operation enables generation for approximately ten and one-half (10-1/2) hours per day or slightly in excess of five (5) hours per tide. The installed capacity will be 12 MW utilizing 2 to 6 MW units. An axial flow, or Bulb type of turbine was selected for this study.

  4. International negotiations in the foundry engineering

    Directory of Open Access Journals (Sweden)

    L. Wojtynek

    2008-04-01

    Full Text Available The aim of this paper is to introduce the essence of negotiations in general, which could find it’s application in foundry engineering. The paper is the result of long cooperation of the authors with foundry engineering and their participation in negotiations between the domestic and foreign companies. In this paper the essence and the rules of negotiations have been introduced. It presents also the skills and abilities of the negotiators. The cycle of negotiations and the following stages of negotiations have been also described. The authors have presented the characteristics of negotiations led by the partners from different parts of the world with particular emphasize on Asian and European countries as with these partners the negotiations in Polish foundries are mainly led.

  5. Arena Cove, California Tsunami Forecast Grids for MOST Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Arena Cove, California Forecast Grids provides bathymetric data strictly for tsunami inundation modeling with the Method of Splitting Tsunami (MOST) model. MOST...

  6. Selected Hydrologic Data for Sand Cove Wash, Washington County, Utah

    National Research Council Canada - National Science Library

    Norton, Aaron; Susong, David D

    2004-01-01

    .... Hydrologic data collected in this study are described and listed in this report. Six boreholes were drilled in Sand Cove Wash to determine the vertical and spatial distribution of the alluvial deposits and their hydrologic...

  7. Elfin Cove, Alaska Tsunami Forecast Grids for MOST Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — The Elfin Cove, Alaska Forecast Grids provides bathymetric data strictly for tsunami inundation modeling with the Method of Splitting Tsunami (MOST) model. MOST is a...

  8. 77 FR 32998 - Foundry Coke From China

    Science.gov (United States)

    2012-06-04

    ... China Determination On the basis of the record \\1\\ developed in the subject five-year review, the United... China would be likely to lead to continuation or recurrence of material injury to an industry in the... Publication 4326 (May 2012), entitled Foundry Coke from China: Investigation No. 731-TA-891 (Second Review...

  9. 76 FR 35886 - Orange Cove Irrigation District, and Friant Power Authority; Notice of Availability of...

    Science.gov (United States)

    2011-06-20

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Project No. 11068-014--California] Orange Cove Irrigation District, and Friant Power Authority; Notice of Availability of Environmental... has prepared an Environmental Assessment (EA) regarding Orange Cove Irrigation District's and Friant...

  10. Benchmarking NNWSI flow and transport codes: COVE 1 results

    International Nuclear Information System (INIS)

    Hayden, N.K.

    1985-06-01

    The code verification (COVE) activity of the Nevada Nuclear Waste Storage Investigations (NNWSI) Project is the first step in certification of flow and transport codes used for NNWSI performance assessments of a geologic repository for disposing of high-level radioactive wastes. The goals of the COVE activity are (1) to demonstrate and compare the numerical accuracy and sensitivity of certain codes, (2) to identify and resolve problems in running typical NNWSI performance assessment calculations, and (3) to evaluate computer requirements for running the codes. This report describes the work done for COVE 1, the first step in benchmarking some of the codes. Isothermal calculations for the COVE 1 benchmarking have been completed using the hydrologic flow codes SAGUARO, TRUST, and GWVIP; the radionuclide transport codes FEMTRAN and TRUMP; and the coupled flow and transport code TRACR3D. This report presents the results of three cases of the benchmarking problem solved for COVE 1, a comparison of the results, questions raised regarding sensitivities to modeling techniques, and conclusions drawn regarding the status and numerical sensitivities of the codes. 30 refs

  11. Environmental favourable foundries through maintenance activities

    Directory of Open Access Journals (Sweden)

    A. Saniuk

    2015-10-01

    Full Text Available Maintenance today contributes to the aim of sustainable development in society, including environmental and energy saving, safety and economical aspects. The main purpose of the paper is to present the role of maintenance in the realization of sustainable developing practices in a foundry industry. Maintenance offers numerous opportunities to reduce the influence of foundry processes on the natural environment and utilize resources more efficiently. Maintenance activities can help to reduce losses and thereby improve the efficiency of the processes used in the production of resources (e.g. raw materials, energy, etc., especially in areas such as: the choice of an appropriate strategy for the maintenance of machinery and equipment (e.g. reactive, preventive, proactive; inventory management of spare parts; lubrication management and management of technology media.

  12. The geology of Burnsville Cove, Bath and Highland Counties, Virginia

    Science.gov (United States)

    Swezey, Christopher; Haynes, John T.; Lambert, Richard A.; White, William B.; Lucas, Philip C.; Garrity, Christopher P.

    2015-01-01

    Burnsville Cove is a karst region in Bath and Highland Counties of Virginia. A new geologic map of the area reveals various units of limestone, sandstone, and siliciclastic mudstone (shale) of Silurian through Devonian age, as well as structural features such as northeast-trending anticlines and synclines, minor thrust faults, and prominent joints. Quaternary features include erosional (strath) terraces and accumulations of mud, sand, and gravel. The caves of Burnsville Cove are located within predominantly carbonate strata above the Silurian Williamsport Sandstone and below the Devonian Oriskany Sandstone. Most of the caves are located within the Silurian Tonoloway Limestone, rather than the Silurian-Devonian Keyser Limestone as reported previously.

  13. An investigation of waste foundry sand in asphalt concrete mixtures.

    Science.gov (United States)

    Bakis, Recep; Koyuncu, Hakan; Demirbas, Ayhan

    2006-06-01

    A laboratory study regarding the reuse of waste foundry sand in asphalt concrete production by replacing a certain portion of aggregate with WFS was undertaken. The results showed that replacement of 10% aggregates with waste foundry sand was found to be the most suitable for asphalt concrete mixtures. Furthermore, the chemical and physical properties of waste foundry sand were analysed in the laboratory to determine the potential effect on the environment. The results indicated that the investigated waste foundry sand did not significantly affect the environment around the deposition

  14. Autonomous Slat-Cove-Filler Device for Reduction of Aeroacoustic Noise Associated with Aircraft Systems

    Science.gov (United States)

    Turner, Travis L. (Inventor); Kidd, Reggie T. (Inventor); Lockard, David P (Inventor); Khorrami, Mehdi R. (Inventor); Streett, Craig L. (Inventor); Weber, Douglas Leo (Inventor)

    2016-01-01

    A slat cove filler is utilized to reduce airframe noise resulting from deployment of a leading edge slat of an aircraft wing. The slat cove filler is preferably made of a super elastic shape memory alloy, and the slat cove filler shifts between stowed and deployed shapes as the slat is deployed. The slat cove filler may be configured such that a separate powered actuator is not required to change the shape of the slat cove filler from its deployed shape to its stowed shape and vice-versa. The outer contour of the slat cove filler preferably follows a profile designed to maintain accelerating flow in the gap between the slat cove filler and wing leading edge to provide for noise reduction.

  15. Urinary 1-hydroxypyrene, a PAH biomarker in foundry workers

    DEFF Research Database (Denmark)

    Omland, Øyvind; Sherson, David; Hansen, Åse Marie

    1996-01-01

    Exposure to PAH in foundry workers has been studied by urinary 1-hydroxypyrene (HPU) levels, quantitatively measured by reversed phase HPLC. Seventy male foundry workers and 68 matched controls were investigated. Polycyclic aromatic hydrocarbon (PAH) exposure was defined by 17 breathing zone hygi...

  16. MEMS/MOEMS foundry services at INO

    Science.gov (United States)

    García-Blanco, Sonia; Ilias, Samir; Williamson, Fraser; Généreux, Francis; Le Noc, Loïc; Poirier, Michel; Proulx, Christian; Tremblay, Bruno; Provençal, Francis; Desroches, Yan; Caron, Jean-Sol; Larouche, Carl; Beaupré, Patrick; Fortin, Benoit; Topart, Patrice; Picard, Francis; Alain, Christine; Pope, Timothy; Jerominek, Hubert

    2010-06-01

    In the MEMS manufacturing world, the "fabless" model is getting increasing importance in recent years as a way for MEMS manufactures and startups to minimize equipment costs and initial capital investment. In order for this model to be successful, the fabless company needs to work closely with a MEMS foundry service provider. Due to the lack of standardization in MEMS processes, as opposed to CMOS microfabrication, the experience in MEMS development processes and the flexibility of the MEMS foundry are of vital importance. A multidisciplinary team together with a complete microfabrication toolset allows INO to offer unique MEMS foundry services to fabless companies looking for low to mid-volume production. Companies that benefit from their own microfabrication facilities can also be interested in INO's assistance in conducting their research and development work during periods where production runs keep their whole staff busy. Services include design, prototyping, fabrication, packaging, and testing of various MEMS and MOEMS devices on wafers fully compatible with CMOS integration. Wafer diameters ranging typically from 1 inch to 6 inches can be accepted while 8-inch wafers can be processed in some instances. Standard microfabrication techniques such as metal, dielectric, and semiconductor film deposition and etching as well as photolithographic pattern transfer are available. A stepper permits reduction of the critical dimension to around 0.4 μm. Metals deposited by vacuum deposition methods include Au, Ag, Al, Al alloys, Ti, Cr, Cu, Mo, MoCr, Ni, Pt, and V with thickness varying from 5 nm to 2 μm. Electroplating of several materials including Ni, Au and In is also available. In addition, INO has developed and built a gold black deposition facility to answer customer's needs for broadband microbolometric detectors. The gold black deposited presents specular reflectance of less than 10% in the wavelength range from 0.2 μm to 100 μm with thickness ranging from

  17. New EUROPRACTICE microsystem design and foundry services

    Science.gov (United States)

    Salomon, Patric R.; Beernaert, Dirk; Turner, Rob

    2000-08-01

    The microsystems market for MST is predicted to grow to 38 billion dollars by the year 2002, with systems containing these components generating even higher revenues and growth. One of the barriers to successful exploitation of this technology has been the lack of access to industrial foundries capable of producing certified microsystems devices in commercial quantities. To overcome this problem, the European Commission has started the EUROPRACTICE program in 1996 with the installation of manufacturing clusters and demonstration activities to provide access to microsystems foundry services for European small and medium sized companies (SMEs). Since 1996, there has been a shift form providing 'broad technology offers' and 'raising awareness fro microsystem capabilities' to 'direct support of design needs' and 'focused services' which allow SMEs to use even complex microsystems technologies to implement their products, The third phase of EUROPRACTICE has just been launched, and contains 5 Manufacturing Clusters, 12 Designs Houses, and 7 Competence Centers, each working in different application/technology areas. The EUROPRACTICE program will be presented together with a detail description of the capabilities of the participants and information on how to access their services.

  18. Wafer-shape metrics based foundry lithography

    Science.gov (United States)

    Kim, Sungtae; Liang, Frida; Mileham, Jeffrey; Tsai, Damon; Bouche, Eric; Lee, Sean; Huang, Albert; Hua, C. F.; Wei, Ming Sheng

    2017-03-01

    As device shrink, there are many difficulties with process integration and device yield. Lithography process control is expected to be a major challenge due to tighter overlay and focus control requirement. The understanding and control of stresses accumulated during device fabrication has becoming more critical at advanced technology nodes. Within-wafer stress variations cause local wafer distortions which in turn present challenges for managing overlay and depth of focus during lithography. A novel technique for measuring distortion is Coherent Gradient Sensing (CGS) interferometry, which is capable of generating a high-density distortion data set of the full wafer within a time frame suitable for a high volume manufacturing (HVM) environment. In this paper, we describe the adoption of CGS (Coherent Gradient Sensing) interferometry into high volume foundry manufacturing to overcome these challenges. Leveraging this high density 3D metrology, we characterized its In-plane distortion as well as its topography capabilities applied to the full flow of an advanced foundry manufacturing. Case studies are presented that summarize the use of CGS data to reveal correlations between in-plane distortion and overlay variation as well as between topography and device yield.

  19. Small Scale Foundries in Ghana: The challenges

    Directory of Open Access Journals (Sweden)

    Anthony ANDREWS

    2012-08-01

    Full Text Available Small Scale Foundries (SSFs have been in existence for several years in Ghana. The industry has created several jobs for the people of Ghana and has minimized the burden on government to find ways of disposing scrap metals generated within the country. While scrap metals are still being exported, the quantity exported has decreased as a result of recycling by foundrymen in producing various parts. The government of Ghana has not paid special attention to this industry. Nevertheless, individuals and private investors are heavily involved in producing several thousands of tonnes of castings annually generating revenue for the government through taxation as well as helping with metal waste disposal. Metal cast products are sold both locally and internationally to neighbouring countries. The industry is however faced with numerous challenges. These include quality issues due to lack of technical know-how, access to funding from both government and private financial institutions and foundry waste management. To promote this industry, government and private financial institutions must be encouraged to come on board. Policies must be established and proper training programme developed to improve and promote this technology. This could go a long way in reducing the high unemployment rate in Ghana.

  20. Hybrid foundry patterns of bevel gears

    Directory of Open Access Journals (Sweden)

    Budzik G.

    2007-01-01

    Full Text Available Possibilities of making hybrid foundry patterns of bevel gears for investment casting process are presented. Rapid prototyping of gears with complex tooth forms is possible with the use of modern methods. One of such methods is the stereo-lithography, where a pattern is obtained as a result of resin curing with laser beam. Patterns of that type are applicable in precision casting. Removing of stereo-lithographic pattern from foundry mould requires use of high temperatures. Resin burning would generate significant amounts of harmful gases. In case of a solid stereo-lithographic pattern, the pressure created during gas burning may cause the mould to crack. A gas volume reduction may be achieved by using patterns of honeycomb structure. However, this technique causes a significant worsening of accuracy of stereo-lithographic patterns in respect of their dimensions and shape. In cooperation with WSK PZL Rzeszów, the Machine Design Department of Rzeszow University of Technology carried out research on the design of hybrid stereo-lithographic patterns. Hybrid pattern consists of a section made by stereo-lithographic process and a section made of casting wax. The latter material is used for stereo-lithographic pattern filling and for mould gating system. The hybrid pattern process consists of two stages: wax melting and then the burn-out of stereolithographic pattern. Use of hybrid patterns reduces the costs of production of stereolithographic patterns. High dimensional accuracy remains preserved in this process.

  1. Modern sedimentation patterns in Potter Cove, King George Island, Antarctica

    Science.gov (United States)

    Hass, H. Christian; Kuhn, Gerhard; Wölfl, Anne-Cathrin; Wittenberg, Nina; Betzler, Christian

    2013-04-01

    IMCOAST among a number of other initiatives investigates the modern and the late Holocene environmental development of south King George Island with a strong emphasis on Maxwell Bay and its tributary fjord Potter Cove (maximum water depth: about 200 m). In this part of the project we aim at reconstructing the modern sediment distribution in the inner part of Potter Cove using an acoustic ground discrimination system (RoxAnn) and more than136 ground-truth samples. Over the past 20 years the air temperatures in the immediate working area increased by more than 0.6 K (Schloss et al. 2012) which is less than in other parts of the West Antarctic Peninsula (WAP) but it is still in the range of the recovery of temperatures from the Little Ice Age maximum to the beginning of the 20th century. Potter Cove is a small fjord characterized by a series of moraine ridges produced by a tidewater glacier (Fourcade Glacier). Presumably, the farthest moraine is not much older than about 500 years (LIA maximum), hence the sediment cover is rather thin as evidenced by high resolution seismic data. Since a few years at least the better part of the tidewater glacier retreated onto the island's mainland. It is suggested that such a fundamental change in the fjord's physiography has also changed sedimentation patterns in the area. Potter Cove is characterized by silty-clayey sediments in the deeper inner parts of the cove. Sediments are coarser (fine to coarse sands and boulders) in the shallower areas; they also coarsen from the innermost basin to the mouth of the fjord. Textural structures follow the seabed morphology, i.e. small v-shaped passages through the moraine ridges. The glacier still produces large amounts of turbid melt waters that enter the cove at various places. We presume that very fine-grained sediments fall out from the meltwater plumes and are distributed by mid-depth or even bottom currents, thus suggesting an anti-estuarine circulation pattern. Older sediments that are

  2. Commercial negotiations in the foundry engineering

    Directory of Open Access Journals (Sweden)

    L. Wojtynek

    2008-10-01

    Full Text Available The article presents the process of commercial negotiations paying attention to the negotiation itself as well as to its basic elements. The specificity of the Polish foundries’ main negotiation partners from The European Union, who are the deliverers of diverse casting range, was specified. The most important cultural factors, which determine the process of negotiations conducted by the representatives of various cultural groups, were analysed. The understanding of cultural differences and adapting to them while negotiating are important factors which constitute the parties’ negotiation process. The meaning of price in the commercial negotiation process was described. The elements of sale process and the factors which influence the casts price were enumerated. What is more, the main methods of determining price were characterized. The essential problems connected with conducting the price negotiations in foundries were indicated.

  3. Maintenance system improvement in cast iron foundry

    Directory of Open Access Journals (Sweden)

    S. Kukla

    2011-07-01

    Full Text Available The work presents the issue of technical equipment management in an iron foundry basing on the assumptions of the TPM system (Total Productive Maintenance. Exploitation analysis of automatic casting lines has been carried out and their work’s influence on the whole production system’s functioning has been researched. Within maintenance system improvement, implementation of autonomic service and planned lines’ review have been proposed in order to minimize the time of breakdown stoppages. The SMED method was used to optimize changeover time, and the OEE (Overall Equipment Effectiveness was applied to evaluate the level of resources usage before and after implementing changes. Further, the influence of the maintenance strategy of casting devices’ efficiency on own costs of casting manufac- ture was estimated.

  4. Ion traps fabricated in a CMOS foundry

    Energy Technology Data Exchange (ETDEWEB)

    Mehta, K. K.; Ram, R. J. [Department of Electrical Engineering and Computer Science, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Eltony, A. M.; Chuang, I. L. [Center for Ultracold Atoms, Research Laboratory of Electronics and Department of Physics, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States); Bruzewicz, C. D.; Sage, J. M., E-mail: jsage@ll.mit.edu; Chiaverini, J., E-mail: john.chiaverini@ll.mit.edu [Lincoln Laboratory, Massachusetts Institute of Technology, Lexington, Massachusetts 02420 (United States)

    2014-07-28

    We demonstrate trapping in a surface-electrode ion trap fabricated in a 90-nm CMOS (complementary metal-oxide-semiconductor) foundry process utilizing the top metal layer of the process for the trap electrodes. The process includes doped active regions and metal interconnect layers, allowing for co-fabrication of standard CMOS circuitry as well as devices for optical control and measurement. With one of the interconnect layers defining a ground plane between the trap electrode layer and the p-type doped silicon substrate, ion loading is robust and trapping is stable. We measure a motional heating rate comparable to those seen in surface-electrode traps of similar size. This demonstration of scalable quantum computing hardware utilizing a commercial CMOS process opens the door to integration and co-fabrication of electronics and photonics for large-scale quantum processing in trapped-ion arrays.

  5. Web-based expert system for foundry pollution prevention

    Science.gov (United States)

    Moynihan, Gary P.

    2004-02-01

    Pollution prevention is a complex task. Many small foundries lack the in-house expertise to perform these tasks. Expert systems are a type of computer information system that incorporates artificial intelligence. As noted in the literature, they provide a means of automating specialized expertise. This approach may be further leveraged by implementing the expert system on the internet (or world-wide web). This will allow distribution of the expertise to a variety of geographically-dispersed foundries. The purpose of this research is to develop a prototype web-based expert system to support pollution prevention for the foundry industry. The prototype system identifies potential emissions for a specified process, and also provides recommendations for the prevention of these contaminants. The system is viewed as an initial step toward assisting the foundry industry in better meeting government pollution regulations, as well as improving operating efficiencies within these companies.

  6. Foundry based approach for InP based PIC development

    NARCIS (Netherlands)

    Smit, M.K.

    2014-01-01

    Europe is making significant investments in development of generic photonic foundry platform infrastructures for InP-based and Silicon Photonic ICs. Here we present the present status for the InP-based JePPIX platform.

  7. Guide to energy efficiency opportunities in Canadian foundries

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    In Canada, the foundry sector employs about 15000 people and most of the companies are members of the Canadian Foundry Association (CFA). The CFA is committed to reducing its greenhouse gas emissions and is therefore looking for energy savings which, in addition to reducing emissions, would help the industry save costs and improve its competitiveness. The aim of this document is to provide operators with a guide to improving energy efficiency in their foundries. The report provides guidance on carrying out energy audits, gathering energy saving ideas, prioritizing projects, and charting the course of improved energy performance. Many different energy saving ideas for many kinds of operation are presented in this guidebook as a help to operators in finding where they could improve their energy efficiency; references to energy saving methods from all over the world are provided. This guidebook is a useful tool for helping foundry operators improve energy efficiency in their operations.

  8. Development of risk assessment tool for foundry workers.

    Science.gov (United States)

    Mohan, G Madhan; Prasad, P S S; Mokkapati, Anil Kumar; Venkataraman, G

    2008-01-01

    Occupational ill-health and work-related disorders are predominant in manufacturing industries due to the inevitable presence of manual work even after several waves of industrial automation and technological advancements. Ergonomic risk factors and musculoskeletal disorders like low-back symptoms have been noted amongst foundry workers. The purpose of this study was to formulate and develop a Physical Effort Index to assess risk factor. The questionnaire tool applicable to foundry environment has been designed and validated. The data recorded through survey across the foundries has been subjected to regression analysis to correlate between proposed physical effort index and the standard Borg's Ratings of Perceived Exertion (RPE) scale. The physical efforts of sixty seven workers in various foundry shop floors were assessed subjectively. The 'Job factors' and 'Work environment' were the two major parameters considered in assessing the worker discomfort level at workplace. A relation between Borg's RPE scale and the above two parameters were arrived at, through regression analysis. The study demonstrates the prevalence of risk factors amongst foundry workers and the effectiveness of the proposed index in estimating the risk factor levels. RELEVANCE TO THE INDUSTRY: The proposed tool will assist foundry supervisors and managers to assess the risk factors and helps in better understanding of the workplace to avoid work-related disorders, ensuring better output.

  9. 77 FR 33446 - Jordan Cove Energy Project, L.P.; Application for Long-Term Authorization to Export Liquefied...

    Science.gov (United States)

    2012-06-06

    ....\\2\\ \\2\\ Jordan Cove states that under the LTA business model, the decision whether to utilize... that presumption ``by making an affirmative showing of inconsistency with the public interest.'' \\6\\ \\5... Cove is highlighted in Jordan Cove's application. Based on the reasoning provided in the Application...

  10. COVE: a visual environment for ocean observatory design

    International Nuclear Information System (INIS)

    Grochow, K; Lazowska, E; Stoermer, M; Kelley, D; Delaney, J

    2008-01-01

    Physical, chemical, and biological ocean processes play a crucial role in determining Earth's environment. Unfortunately, our knowledge of these processes is limited because oceanography is carried out today largely the way it was a century ago: as expeditionary science, going to sea in ships and measuring a relatively small number of parameters (e.g., temperature, salinity, and pressure) as time and budget allow. The NSF Ocean Observatories Initiative is a US$330 million project that will help transform oceanography from a data-poor to a data-rich science. A cornerstone of this project is the deep water Regional Scale Nodes (RSN) that will be installed off the coasts of Washington and Oregon. The RSN will include 1500 km of fiber optic cable providing power and bandwidth to the seafloor and throughout the water column. Thousands of sensors will be deployed to stream data and imagery to shore, where they will be available in real time for ocean scientists and the public at large. The design of the RSN is a complex undertaking, requiring a combination of many different interactive tools and areas of visualization: geographic visualization to see the available seafloor bathymetry, scientific visualization to examine existing geospatially located datasets, layout tools to place the sensors, and collaborative tools to communicate across the team during the design. COVE, the Common Observatory Visualization Environment, is a visualization environment designed to meet all these needs. COVE has been built by computer scientists working closely with the engineering and scientific teams who will build and use the RSN. This paper discusses the data and activities of cabled observatory design, the design of COVE, and results from its use across the team

  11. Unsteady characteristics of a slat-cove flow field

    Science.gov (United States)

    Pascioni, Kyle A.; Cattafesta, Louis N.

    2018-03-01

    The leading-edge slat of a multielement wing is a significant contributor to the acoustic signature of an aircraft during the approach phase of the flight path. An experimental study of the two-dimensional 30P30N geometry is undertaken to further understand the flow physics and specific noise source mechanisms. The mean statistics from particle image velocimetry (PIV) shows the differences in the flow field with angle of attack, including the interaction between the cove and trailing-edge flow. Phase-locked PIV successfully links narrow-band peaks found in the surface pressure spectrum to shear layer instabilities and also reveals that a bulk cove oscillation at a Strouhal number based on a slat chord of 0.15 exists, indicative of shear layer flapping. Unsteady surface pressure measurements are documented and used to estimate spanwise coherence length scales. A narrow-band frequency prediction scheme is also tested and found to agree well with the data. Furthermore, higher-order spectral analysis suggests that nonlinear effects cause additional peaks to arise in the power spectrum, particularly at low angles of attack.

  12. 31. Introduction with adjacent production of foundry and rolling department of electrolysis shop

    International Nuclear Information System (INIS)

    Ivanov, A.V.

    1993-01-01

    The introduction with adjacent production of foundry and rolling department of electrolysis shop was conducted. The foundry machine was described. The chemical properties of aluminium for ferrous alloy production were defined.

  13. Reduced energy consumption for melting in foundries

    Energy Technology Data Exchange (ETDEWEB)

    Skov-Hansen, S.

    2007-09-15

    By improving the gating technology in traditional gating systems it is possible to reduce the amount of metal to be re-melted, and hence reduce the energy consumption for melting in foundries. Traditional gating systems are known for a straight tapered down runner a well base and 90 deg. bends in the runner system. In the streamlined gating systems there are no sharp changes in direction and a large effort is done to confine and control the flow of the molten metal during mould filling. Experiments in real production lines have proven that using streamlined gating systems improves yield by decreasing the poured weight compared to traditional layouts. In a layout for casting of valve housings in a vertically parted mould the weight of the gating system was reduced by 1,1kg which is a 20% weight reduction for the gating system. In a layout for horizontally parted moulds the weight of the gating system has been reduced by 3,7kg which is a weight reduction of 60% for the gating system. The experiments casting valve housings in ductile iron also proved that it is possible to lower the pouring temperature from 1400 deg. C to 1300 deg. C without the risk of cold runs. Glass plate fronted moulds have been used to study the flow of melt during mould filling. These experiments have also been used for studying the flow pattern when ceramic filters are used. The thorough study of the use of filters revealed that the metal passing through the filter is divided into a number of small jets. This proves that filters do not have the claimed positive effect on the flow of metal. The volumes necessary on either side of the filter is not filled till a backpressure is build up and results in formation of pressure shocks when backfilled. These pressure shocks result in more turbulence inside the casting than the same gating system with no filter. Not using filters can mean a reduction in poured weight of 0,6kg. To examine if the experiments using glass plate fronted moulds give

  14. Rationalization of foundry processes on the basis of simulation experiment

    Directory of Open Access Journals (Sweden)

    S. Kukla

    2008-10-01

    Full Text Available The paper presents results of research obtained on the basis of simulation experiment, whose aim was to analyze the performance of cast iron foundry. A simulation model of automobile industry foundry was made. The course of the following processes was analyzedin a computer model: preparation of liquid cast iron, forming and filling the moulds, cooling and stamping the castings, cleaning andfinishing treatment. The sheets of multi-criterion evaluation were prepared, where criteria and variants were assessed by meansof subjective point evaluation and fuzzy character evaluation. The paper presents an analysis example of finishing activities of castings realized in foundry on traditional machines and efficient presses and in cooperation. On the basis of reports from a simulation experiment information was achieved related to activities’ duration, load of accessible resources, the problems of storage and transport, bottle necks in the system and appearing queues in from of workplaces. The research used a universal modelling and simulation packet for productionsystems - ARENA.

  15. Prevalence of job strain among Indian foundry shop floor workers.

    Science.gov (United States)

    Mohan, G Madhan; Elangovan, S; Prasad, P S S; Krishna, P Rama; Mokkapati, Anil Kumar

    2008-01-01

    Global competition in manufacturing sector demand higher productivity levels. In this context, workers in this sector are set with high output targets, leading to job strain. In addition to the strain, hazardous conditions also prevail in some of the manufacturing processes like foundry activities. This paper attempts to appraise the prevalence of job strain among foundry shop floor workers in India with the help of Demands-Control model [8]. In this study, data was collected through a survey using 49-item Job Content Questionnaire (JCQ) [9], a widely used and well-validated test for job strain. Then the data was subjected to statistical analysis after ascertaining the reliability. This survey has revealed that 25% of workers in foundry were experiencing high job strain. Hazardous working conditions, limited decision making authority, etc. appear to be the main contributing factors for the higher levels of strain.

  16. Exposure of iron foundry workers to polycyclic aromatic hydrocarbons

    DEFF Research Database (Denmark)

    Omland, Øyvind; Sherson, D; Hansen, Å M

    1994-01-01

    Exposure to polycyclic aromatic hydrocarbons (PAHs) in foundry workers has been evaluated by determination of benzo(a)pyrene-serum albumin adducts and urinary 1-hydroxypyrene. Benzo(a)pyrene binding to albumin and 1-hydroxypyrene were quantitatively measured by enzyme linked immunosorbent assay...... (ELISA) and reverse phase high performance liquid chromatography (HPLC), respectively. 70 male foundry workers and 68 matched controls were investigated. High and low exposure groups were defined from breathing zone hygienic samples, consisting of 16 PAH compounds in particulate and gaseous phase. Mean...... total PAH was 10.40 micrograms/m3 in the breathing zone, and mean dust adsorbed PAH was 0.15 microgram/m. All carcinogenic PAH was adsorbed to dust. Median benzo(a)pyrene-albumin adduct concentrations (10-90% percentiles) were similar in foundry workers (smokers 0.55 (0.27-1.00) and non-smokers 0.58 (0...

  17. The AHP method used in assessment of foundry enterprise position

    Directory of Open Access Journals (Sweden)

    J. Szymszal

    2008-10-01

    Full Text Available Complex assessment of activity of a selected foundry enterprise based on a modern AHP (Analytic Hierarchy Process method has beenpresented. Having defined the areas of analysis, which include: marketing (products, distribution channels, sales organisation and client concentration, personnel (skills, managerial abilities, organisation climate, effectiveness of incentives, personnel fluctuations, production (availability of raw materials, technical level of production, effective use of production capacities, organisation and management (foundry structure, organisation culture, management performance, the analysis was made using the weighted sum of evaluations. The second step consisted in a comparative assessment of Foundry position using Saaty’s scale modified by Weber and the AHP method with examinationof a hierarchy structure involving the main (parent problem and its direct evolution into sub-problems. The assessment of Foundryposition made by AHP enables introducing changes and/or innovations which are expected to improve the overall productioneffectiveness.

  18. Modified polysaccharides as alternative binders for foundry industry

    Directory of Open Access Journals (Sweden)

    K. Kaczmarska

    2016-10-01

    Full Text Available Polysaccharides constitute a wide group of important polymers with many commercial applications, for example food packaging, fibres, coatings, adhesives etc. This review is devoted to the presentation of polysaccharide application in foundry industry. In this paper the selected properties of foundry moulding sand and core sand containing modified polysaccharides as binders are presented according to foreign literature data. Also, author’s own research about effect of using moulding sand binder consisting of modified polysaccharide (modified starch or its composition with non-toxic synthetic polymers are discussed. Based on technologies taken under consideration in this paper, it could be concluded that polysaccharides are suitable as an alternative for use as binder in foundry moulding applications.

  19. Management of Assortment Inventory Groups in Selected Foundry

    Directory of Open Access Journals (Sweden)

    Szymszal J.

    2015-09-01

    Full Text Available As experience shows the practical, reliable assessment and optimisation of total costs of logistical processes implemented in supply chains of foundry plants is a quite complex and complicated process, because it requires to enclose all, without exception, performed actions, including them in various reference cross-sections, systematic activities and finally transforming them in a totally homogenous collection. Only solid analysis and assessment of assortment management in logistical supply systems in foundry plants of particular assortment groups allows to lower the supply costs significantly. In the article the analysis and assessment of the newest implemented optimising algorithms are presented in the process stock management of selected material groups used in a production process of a chosen foundry plant. A practical solution to solve a problem of rotary stock cost minimisation is given as well as of costs while creating a stock with the usage of economical volume and value of order.

  20. Building biological foundries for next-generation synthetic biology.

    Science.gov (United States)

    Chao, Ran; Yuan, YongBo; Zhao, HuiMin

    2015-07-01

    Synthetic biology is an interdisciplinary field that takes top-down approaches to understand and engineer biological systems through design-build-test cycles. A number of advances in this relatively young field have greatly accelerated such engineering cycles. Specifically, various innovative tools were developed for in silico biosystems design, DNA de novo synthesis and assembly, construct verification, as well as metabolite analysis, which have laid a solid foundation for building biological foundries for rapid prototyping of improved or novel biosystems. This review summarizes the state-of-the-art technologies for synthetic biology and discusses the challenges to establish such biological foundries.

  1. Logic Foundry: Rapid Prototyping for FPGA-Based DSP Systems

    Directory of Open Access Journals (Sweden)

    Bhattacharyya Shuvra S

    2003-01-01

    Full Text Available We introduce the Logic Foundry, a system for the rapid creation and integration of FPGA-based digital signal processing systems. Recognizing that some of the greatest challenges in creating FPGA-based systems occur in the integration of the various components, we have proposed a system that targets the following four areas of integration: design flow integration, component integration, platform integration, and software integration. Using the Logic Foundry, a system can be easily specified, and then automatically constructed and integrated with system level software.

  2. Characterization and extraction of gold contained in foundry industrial wastes

    International Nuclear Information System (INIS)

    Vite T, J.; Vite T, M.; Diaz C, A.; Carreno de Leon, C.

    1999-01-01

    Gold was characterized and leached in foundry sands. These wastes are product among others of the automotive industry where they are used as molds material which are contaminated by diverse metals during the foundry. To fulfil the leaching process four coupled thermostat columns were used. To characterize the solid it was used the X-ray diffraction technique. For the qualitative analysis it was used the Activation analysis technique. Finally, for the study of liquors was used the Plasma diffraction spectroscopy (Icp-As) technique. The obtained results show that the process which was used the thermostat columns was more efficient, than the methods traditionally recommended. (Author)

  3. A pilot project: Antioch Delta Cove, Antioch, California

    International Nuclear Information System (INIS)

    Minder, M.

    1994-01-01

    The project involves the restoration of the Hickmott cannery site, comprising approximately 15 acres (three five acre parcels) located on the Delta in inter-city Antioch. Hickmott Foods, Inc., operated a fruit and vegetable cannery between 1905 and the early 1970's, during which time tomato skins, peach and apricot pits, and asparagus butts were discharged on the site. The decaying fruit pits have caused cyanide contamination. Additionally, the site contains some petroleum hydrocarbon contamination as well as gypsum board contamination, apparently from nearby manufacturing operations. The Antioch Delta Cove Pilot shows how interested parties can work together to clean up contaminated sites and use the clean up process to stimulate technology transfer. The Antioch project is a blueprint that can be replicated at other sites across California

  4. Manganese exposure in foundry furnacemen and scrap recycling workers

    DEFF Research Database (Denmark)

    Lander, F; Kristiansen, J; Lauritsen, Jens

    1999-01-01

    Cast iron products are alloyed with small quantities of manganese, and foundry furnacemen are potentially exposed to manganese during tapping and handling of smelts. Manganese is a neurotoxic substance that accumulates in the central nervous system, where it may cause a neurological disorder...

  5. Using lean methodologies for economically and environmentally sustainable foundries

    Directory of Open Access Journals (Sweden)

    R. M. Torielli

    2011-02-01

    Full Text Available Lean manufacturing is often seen as a set of tools that reduce the total cost and improve the quality of manufactured products. The lean management philosophy is one which targets waste reduction in every facet of the manufacturing business; however, only recently have studies linked lean management philosophies with improving environmental sustainability. These studies suggest that lean manufacturing is more than a set of lean tools that can optimize manufacturing efficiencies; it is a process and mindset that needs to be integrated into daily manufacturing systems to achieve sustainability. The foundry industry, as well as manufacturing in general, has significant challenges in the current regulatory and political climate with developing an economically and environmentally sustainable business model. Lean manufacturing has proven itself as a model for both economic sustainability and environmental stewardship. Several recent studies have shown that both lean and green techniques and “zero-waste” policies also lead to reductions in overall cost. While these strategies have been examined for general manufacturing, they have not been investigated in detail for the foundry industry. This paper will review the current literature and describe how lean and green can provide a relevant framework for environmentally and economically sustainable foundries. Examples of lean and green technologies and techniques which can be applied to foundries in a global context will be described.

  6. Granulated blast furnace slag – A boon for foundry industry

    African Journals Online (AJOL)

    Keywords: Silica sand; Blast Furnace Slag; Mould properties; Ferrous and nonferrous ... raw material for the production of cast components in foundry industries. ... applications for conserving natural resources and reduce the cost of the raw .... in an elevated temperature melting furnace with temperature values of 750 to.

  7. Effects of flow separation and cove leakage on pressure and heat-transfer distributions along a wing-cove-elevon configuration at Mach 6.9. [Langley 8-ft high temperature tunnel test

    Science.gov (United States)

    Deveikis, W. D.

    1983-01-01

    External and internal pressure and cold-wall heating-rate distributions were obtained in hypersonic flow on a full-scale heat-sink representation of the space shuttle orbiter wing-elevon-cove configuration in an effort to define effects of flow separation on cove aerothermal environment as a function of cove seal leak area, ramp angle, and free-stream unit Reynolds number. Average free-stream Mach number from all tests was 6.9; average total temperature from all tests was 3360 R; free-stream dynamic pressure ranged from about 2 to 9 psi; and wing angle of attack was 5 deg (flow compression). For transitional and turbulent flow separation, increasing cove leakage progressively increased heating rates in the cove. When ingested mass flow was sufficient to force large reductions in extent of separation, increasing cove leakage reduced heating rates in the cove to those for laminar attached flow. Cove heating-rate distributions calculated with a method that assumed laminar developing channel flow agreed with experimentally obtained distributions within root-mean-square differences that varied between 11 and 36 percent where cove walls were parallel for leak areas of 50 and 100 percent.

  8. Foundry fabricated photonic integrated circuit optical phase lock loop.

    Science.gov (United States)

    Bałakier, Katarzyna; Fice, Martyn J; Ponnampalam, Lalitha; Graham, Chris S; Wonfor, Adrian; Seeds, Alwyn J; Renaud, Cyril C

    2017-07-24

    This paper describes the first foundry-based InP photonic integrated circuit (PIC) designed to work within a heterodyne optical phase locked loop (OPLL). The PIC and an external electronic circuit were used to phase-lock a single-line semiconductor laser diode to an incoming reference laser, with tuneable frequency offset from 4 GHz to 12 GHz. The PIC contains 33 active and passive components monolithically integrated on a single chip, fully demonstrating the capability of a generic foundry PIC fabrication model. The electronic part of the OPLL consists of commercially available RF components. This semi-packaged system stabilizes the phase and frequency of the integrated laser so that an absolute frequency, high-purity heterodyne signal can be generated when the OPLL is in operation, with phase noise lower than -100 dBc/Hz at 10 kHz offset from the carrier. This is the lowest phase noise level ever demonstrated by monolithically integrated OPLLs.

  9. Environmental characterization foundry sands used in sanitary landfills

    International Nuclear Information System (INIS)

    Domingues, L.G.F.; Ferreira, G.C.S.; Pires, M.S.G.; Teixeira, I.; Carnin, R.; Sarro, W.S.

    2016-01-01

    The national solid waste policy recommends reducing solid waste generation and reusing them in different applications. Preliminary studies show that the foundry sand generated from cast metal parts undercut, has excellent applicability in grain size stabilization of soils for geotechnical functions, and therefore, should not be discarded as waste. This study aimed at environmental characterization of two lots of waste foundry sand (WFS), from different industries, to the particle size stabilization of a clayey soil for use in coverage of solid waste in landfills. The methodology included physicochemical characterization tests (grain size, permeability, XRF and heavy metals) and environmental (NBR 10004: 2004, NBR 10005: 2004, NBR 10006: 20004 and acute toxicity with Vibrio fischeri). The results prove the environmental viability of using these lots of WFS as functional material in the composition of landfills. (author)

  10. Logistics of Materials Flow in an Iron Foundry

    Directory of Open Access Journals (Sweden)

    Kukla S.

    2013-09-01

    Full Text Available The article presents issues related to creating and realizing added value by logistic processes and processing in a casting enterprise. It discusses possibilities of improving systems of casts production by evaluating labour intensity of casts manufacture and analyzing manufacturing prime costs. Operations with added value, processes indirectly creating added value and operations without added value have been specified. The problem was presented on the example of materials flow design in a foundry, where casts are manufactured in expendable moulds and using automated foundry lines. On the basis of the Pareto analysis, a group of casts was specified whose manufacture significantly influences the functioning of the whole enterprise. Finishing treatment operations have been particularly underlined, as they are performed away from the line and are among the most labour-consuming processes during casts production.

  11. Determination of thermal conductivity in foundry mould mixtures

    Directory of Open Access Journals (Sweden)

    G. Solenički

    2010-01-01

    Full Text Available For a thorough understanding of the behaviour of foundry mould mixtures, a good knowledge of thermal properties of mould materials is needed. Laboratory determination of thermal conductivity of mould mixtures enables a better control over scabbing defects which are a major problem in green sand mould mixtures. A special instrument has been designed for that purpose and it is described in this work.

  12. A novel application of concentrated solar thermal energy in foundries.

    Science.gov (United States)

    Selvaraj, J; Harikesavan, V; Eshwanth, A

    2016-05-01

    Scrap preheating in foundries is a technology that saves melting energy, leading to economic and environmental benefits. The proposed method in this paper utilizes solar thermal energy for preheating scrap, effected through a parabolic trough concentrator that focuses sunlight onto a receiver which carries the metallic scrap. Scraps of various thicknesses were placed on the receiver to study the heat absorption by them. Experimental results revealed the pattern with which heat is gained by the scrap, the efficiency of the process and how it is affected as the scrap gains heat. The inferences from them gave practical guidelines on handling scraps for best possible energy savings. Based on the experiments conducted, preheat of up to 160 °C and a maximum efficiency of 70 % and a minimum efficiency of 40 % could be achieved across the time elapsed and heat gained by the scrap. Calculations show that this technology has the potential to save around 8 % of the energy consumption in foundries. Cumulative benefits are very encouraging: 180.45 million kWh of energy savings and 203,905 t of carbon emissions cut per year across the globe. This research reveals immense scope for this technology to be adopted by foundries throughout the world.

  13. Materials and processing approaches for foundry-compatible transient electronics

    Science.gov (United States)

    Chang, Jan-Kai; Fang, Hui; Bower, Christopher A.; Song, Enming; Yu, Xinge; Rogers, John A.

    2017-07-01

    Foundry-based routes to transient silicon electronic devices have the potential to serve as the manufacturing basis for “green” electronic devices, biodegradable implants, hardware secure data storage systems, and unrecoverable remote devices. This article introduces materials and processing approaches that enable state-of-the-art silicon complementary metal-oxide-semiconductor (CMOS) foundries to be leveraged for high-performance, water-soluble forms of electronics. The key elements are (i) collections of biodegradable electronic materials (e.g., silicon, tungsten, silicon nitride, silicon dioxide) and device architectures that are compatible with manufacturing procedures currently used in the integrated circuit industry, (ii) release schemes and transfer printing methods for integration of multiple ultrathin components formed in this way onto biodegradable polymer substrates, and (iii) planarization and metallization techniques to yield interconnected and fully functional systems. Various CMOS devices and circuit elements created in this fashion and detailed measurements of their electrical characteristics highlight the capabilities. Accelerated dissolution studies in aqueous environments reveal the chemical kinetics associated with the underlying transient behaviors. The results demonstrate the technical feasibility for using foundry-based routes to sophisticated forms of transient electronic devices, with functional capabilities and cost structures that could support diverse applications in the biomedical, military, industrial, and consumer industries.

  14. Statistical and Visualization Data Mining Tools for Foundry Production

    Directory of Open Access Journals (Sweden)

    M. Perzyk

    2007-07-01

    Full Text Available In recent years a rapid development of a new, interdisciplinary knowledge area, called data mining, is observed. Its main task is extracting useful information from previously collected large amount of data. The main possibilities and potential applications of data mining in manufacturing industry are characterized. The main types of data mining techniques are briefly discussed, including statistical, artificial intelligence, data base and visualization tools. The statistical methods and visualization methods are presented in more detail, showing their general possibilities, advantages as well as characteristic examples of applications in foundry production. Results of the author’s research are presented, aimed at validation of selected statistical tools which can be easily and effectively used in manufacturing industry. A performance analysis of ANOVA and contingency tables based methods, dedicated for determination of the most significant process parameters as well as for detection of possible interactions among them, has been made. Several numerical tests have been performed using simulated data sets, with assumed hidden relationships as well some real data, related to the strength of ductile cast iron, collected in a foundry. It is concluded that the statistical methods offer relatively easy and fairly reliable tools for extraction of that type of knowledge about foundry manufacturing processes. However, further research is needed, aimed at explanation of some imperfections of the investigated tools as well assessment of their validity for more complex tasks.

  15. Prevalence of Occupational Asthma and Respiratory Symptoms in Foundry Workers

    Directory of Open Access Journals (Sweden)

    Servet Kayhan

    2013-01-01

    Full Text Available This cross-sectional study was conducted in a foundry factory to assess the prevalence of respiratory symptoms and occupational asthma in foundry workers. Physical examination, spirometric evaluation, chest radiograph, and a questionnaire related to respiratory symptoms were performed. Monitoring of peak expiratory flow rates, spirometric reversibility test, and high-resolution computed tomographies were performed for the participants having respiratory symptoms and/or impaired respiratory function test. A total of 347 participants including 286 workers from production department and 61 subjects who worked in nonproduction departments were enrolled in this study. It is found that phlegm (n: 71, 20.46% and cough (n: 52, 14.98% were the most frequent symptoms. The other symptoms were breathlessness (n: 28, 8.06%, chest tightness (n: 14, 4.03%, and wheezing (n: 7, 2.01% . The prevalence of occupational asthma was found to be more frequent among the subjects who worked in the production department (n: 48, 16.78% than the other persons who worked in the nonproduction department (n: 3, 4.91% by chi-square test (P: 0.001. To prevent hazardous respiratory effects of the foundry production, an early diagnosis of occupational asthma is very important. Cessation of cigarette smoking and using of protective masks during the working time should be encouraged.

  16. Fly-ash poisoning in the surroundings of foundries

    Energy Technology Data Exchange (ETDEWEB)

    Hupka, E

    1955-01-01

    Chronic articular swellings were observed in colts and cattle grazing in the vicinity of two factories. Postmortem findings included an increased synovial content and a detachment of articular cartilage from the underlying bone. Several of the colts also developed roaring due to paralysis of the recurrent nerves. Analysis of fly-ash samples from the two foundries revealed the following: lead, 16.87 percent and 44.79 percent; zinc, 23.41 percent and 5.28 percent; sulfur, 12.53 percent and 8.20 percent; and arsenic, 0.52 percent and 0.22 percent, respectively. Cadmium levels of 2.22 percent were also found in the dust from one of foundries, while cerium (5.00 percent) was detected in the dust from the other foundry. Identical articular lesions were reproduced in two colts receiving dietary rations containing the forge dusts. Manifestations of pharyngoparalysis also appeared, resulting in pneumonia in one case due to pharyngeal dysphagia. Lead poisoning, complicated by other toxic substances, was suggested as the cause. Analyses of several colt livers revealed contents exceeding 0.2 mg/100 g in all cases.

  17. Peninsula Effects on Birds in a Coastal Landscape: Are Coves More Species Rich than Lobes?

    Directory of Open Access Journals (Sweden)

    Sam Riffell

    2012-10-01

    Full Text Available Peninsula effects - decreasing richness with increasing distance along peninsula lobes - have been identified for many taxa on large peninsulas. Peninsula effects are caused by differences in colonization and extinction predicted by island biogeography or by environmental gradients along the peninsula. We compared species-area regressions for cove patches (i.e., mainland to regressions for lobe patches (i.e., on peninsula tips for wet meadow birds along a highly interdigitated shoreline (northern Lake Huron, USA. We conducted analysis both with and without accounting for variation in habitat and landscape characteristics (i.e., environmental gradients of wet meadows. Species-area regressions for coves did not differ from lobes, nor did these results differ when we accounted for gradients. Similarly, few species were more abundant in coves. Peninsula effects may have been lacking because lobe patches were located ≈ 800 m on average from the mainland, and birds are highly mobile and can easily sample patches over these distances. One important caveat was that wet meadow patches > 5 ha were located in coves, so coves would still be important considerations in conservation plans because of the contribution of large patches to reproductive success, dispersal and population dynamics.

  18. 77 FR 59601 - Dominion Cove Point LNG, LP; Notice of Intent To Prepare an Environmental Assessment for the...

    Science.gov (United States)

    2012-09-28

    ... DEPARTMENT OF ENERGY Federal Energy Regulatory Commission [Docket No. PF12-16-000] Dominion Cove Point LNG, LP; Notice of Intent To Prepare an Environmental Assessment for the Planned Cove Point Liquefaction Project, Request for Comments on Environmental Issues, Notice of On- Site Environmental Review, and Notice of Public Scoping Meetings The...

  19. Getting the Price Right: Costing and Charging Commercial Provision in Centres of Vocational Excellence (CoVEs). Research Report

    Science.gov (United States)

    Aitken, Liz; Chadwick, Arthur; Hughes, Maria

    2006-01-01

    Centres of Vocational Excellence (CoVEs) were established in 2001, intended to be a key driver in enhancing the contribution of the further education (FE) sector to meeting skills needs. Current government policy expects employers and individuals to pay a greater share of the costs of training, particularly at Level 3, which is the CoVE priority…

  20. 33 CFR 165.502 - Safety and Security Zone; Cove Point Liquefied Natural Gas Terminal, Chesapeake Bay, Maryland.

    Science.gov (United States)

    2010-07-01

    ... 33 Navigation and Navigable Waters 2 2010-07-01 2010-07-01 false Safety and Security Zone; Cove... Navigable Waters COAST GUARD, DEPARTMENT OF HOMELAND SECURITY (CONTINUED) PORTS AND WATERWAYS SAFETY... Areas Fifth Coast Guard District § 165.502 Safety and Security Zone; Cove Point Liquefied Natural Gas...

  1. Low noise wing slat system with rigid cove-filled slat

    Science.gov (United States)

    Shmilovich, Arvin (Inventor); Yadlin, Yoram (Inventor)

    2013-01-01

    Concepts and technologies described herein provide for a low noise aircraft wing slat system. According to one aspect of the disclosure provided herein, a cove-filled wing slat is used in conjunction with a moveable panel rotatably attached to the wing slat to provide a high lift system. The moveable panel rotates upward against the rear surface of the slat during deployment of the slat, and rotates downward to bridge a gap width between the stowed slat and the lower wing surface, completing the continuous outer mold line shape of the wing, when the cove-filled slat is retracted to the stowed position.

  2. Laboratory assessment of the influence of the proportion of waste foundry sand on the geotechnical engineering properties of clayey soils

    CSIR Research Space (South Africa)

    Mgangira, Martin B

    2006-01-01

    Full Text Available Soil improvement can be achieved through mechanical stabilisation using industrial byproducts. Clayey soils were blended with waste foundry sand to examine its influence on the geotechnical engineering properties of the soils. The waste foundry sand...

  3. 77 FR 20788 - Foundry Coke Products From the People's Republic of China: Final Results of Expedited Second...

    Science.gov (United States)

    2012-04-06

    ... mm (4 inch) sieve, of a kind used in foundries. The foundry coke products subject to the antidumping... purposes, our written description of the scope of the Order is dispositive. Analysis of Comments Received...

  4. design and fabrication of a fou fabrication of a foundry sand mixer

    African Journals Online (AJOL)

    eobe

    favourably with the the imported existing one which urably with the the imported existing one which foundry shops will eliminate the use manual effort save the the country of huge save the the country of huge foreign exchange used i foreign exchange used i. Keywords: Keywords:foundry,sand mixer,fabrication,design,bla.

  5. Advancing the discussion about systematic classroom behavioral observation, a product review of Tenny, J. (2010). eCOVE observation software. Pacific City, OR: eCOVE Software, LLC.

    Science.gov (United States)

    Froiland, John Mark; Smith, Liana

    2014-05-01

    Applied child psychologists and behavioral consultants often use systematic behavioral observations to inform the psychological assessment and intervention development process for children referred for attention and hyperactivity problems. This article provides a review of the 2010 version of the eCOVE classroom observation software in terms of its utility in tracking the progress of children with attention and hyperactive behaviors and its use in evaluating teacher behaviors that may impede or promote children's attention and positive behavior. The eCOVE shows promise as an efficient tool for psychologists and behavioral consultants who want to evaluate the effects of interventions for children with symptoms of ADHD, ODD, mood disorders and learning disorders; however, some research-based improvements for future models are suggested. The reviewers also share their firsthand experience in using eCOVE to evaluate teacher and student behavior exhibited on a television show about teaching urban high school students and during a movie about an eccentric new kindergarten teacher. Rich examples are provided of using strategic behavioral observations to reveal how to improve the classroom environment so as to facilitate attention, motivation and positive behavior among youth. Broader implications for enhancing the use of systematic behavioral observations in the assessment of children and adolescents with attention disorders and related behavioral problems are discussed. Key issues are examined such as the use of behavioral observations during psychological consultation to prevent the previously found gender bias in referrals for ADHD. Using behavioral observations to enhance differential diagnosis is also discussed.

  6. The management of production value stream factors in a foundry

    Directory of Open Access Journals (Sweden)

    S. Borkowski

    2010-01-01

    Full Text Available Connection of two value streams: production and human resources were proposed as a new approach to the production process. To assess the factors of production value streams the elements of the top of the Toyota's house as well as fourth and sixth Toyota's managing principles were used. On the basis of the feedback from respondents –the foundry workers, there can be determined the validity of series of decisive factors' importance that equalizes the work load and requires the standardization.

  7. High Temperature Thermal Properties of Bentonite Foundry Sand

    Directory of Open Access Journals (Sweden)

    Krajewski P.K.

    2015-06-01

    Full Text Available The paper presents results of measuring thermal conductivity and heat capacity of bentonite foundry sand in temperature range ambient - 900­­°C. During the experiments a technical purity Cu plate was cast into the green-sand moulds. Basing on measurements of the mould temperature field during the solidification of the casting, the temperature relationships of the measured properties were evaluated. It was confirmed that water vaporization strongly influences thermal conductivity of the moulding sand in the first period of the mould heating by the poured casting.

  8. Extraction of toxic and valuable metals from foundry sands

    International Nuclear Information System (INIS)

    Vite T, J.

    1996-01-01

    There were extracted valuable metals from foundry sands such as: gold, platinum, silver, cobalt, germanium, nickel and zinc among others, as well as highly toxic metals such as chromium, lead, vanadium and arsenic. The extraction efficiency was up to 100% in some cases. For this reason there were obtained two patents at the United States, patent number 5,356,601, in October 1994, given for the developed process and patent number 5,376,000, in December 1994, obtained for the equipment employed. Therefore, the preliminary parameters for the installation of a pilot plant have also been developed. (Author)

  9. Re-usage of waste foundry sand in high-strength concrete.

    Science.gov (United States)

    Guney, Yucel; Sari, Yasin Dursun; Yalcin, Muhsin; Tuncan, Ahmet; Donmez, Senayi

    2010-01-01

    In this study, the potential re-use of waste foundry sand in high-strength concrete production was investigated. The natural fine sand is replaced with waste foundry sand (0%, 5%, 10%, and 15%). The findings from a series of test program has shown reduction in compressive and tensile strengths, and the elasticity modulus which is directly related to waste foundry inclusion in concrete. Nevertheless the concrete with 10% waste foundry sand exhibits almost similar results to that of the control one. The slump and the workability of the fresh concrete decreases with the increase of the waste foundry sand ratio. Although the freezing and thawing significantly reduces the mechanical and physical properties of the concrete. The obtained results satisfies the acceptable limits set by the American Concrete Institute (ACI). 2010 Elsevier Ltd. All rights reserved.

  10. Total productive maintenance on example of automated foundry lines

    Directory of Open Access Journals (Sweden)

    S. Kukla

    2009-07-01

    Full Text Available Within framework of the presented study one has performed analysis of stoppages in automatic foundry lines operation, and basing on assumptions from complex maintenance system has undertaken himself to develop a service maintenance schedule for machinery installed in the line. Moreover, one has presented general assumptions of TPM system operated in conditions of series and multi-series production of cast iron castings. One has constructed operational database and has elaborated a list of line stoppage causes within a year. One has proposed a possibility of implementation of manufacturing systems modeling and simulating technique in management of production machinery operation in a foundry shop. Within framework of the simulation experiment one has developed schedules of production, schedules of maintenance and has forecasted indices of general productivity of the machinery for a various scenarios of events on example of casting line having in-series structure of operational reliability. In course of the study there was implemented ARENA universal software package to modeling and simulation of the manufacturing systems.

  11. APPLICATION OF ADDITIVELY MANUFACTURED POLYMER COMPOSITE PROTOTYPES IN FOUNDRY

    Directory of Open Access Journals (Sweden)

    Wiesław Kuczko

    2015-05-01

    Full Text Available The paper presents a method, developed by the authors, for manufacturing polymer composites with the matrix manufactured in a layered manner (via 3D printing – Fused Deposition Modeling out of a thermoplastic material. As an example of practical application of this method, functional prototypes are presented, which were used as elements of foundry tooling – patterns for sand molding. In case of manufacturing prototype castings or short series of products, foundries usually cooperate with modeling studios, which produce patterns by conventional, subtractive manufacturing technologies. If patterns have complex shapes, this results in high manufacturing costs and significantly longer time of tooling preparation. The method proposed by the authors allows manufacturing functional prototypes in a short time thanks to utilizing capabilities of additive manufacturing (3D printing technology. Thanks to using two types of materials simultaneously (ABS combined with chemically hardened resins, the produced prototypes are capable of carrying increased loads. Moreover, the method developed by the authors is characterized by manufacturing costs lower than in the basic technology of Fused Deposition Modeling. During the presented studies, the pattern was produced as a polymer composite and it was used to prepare a mold and a set of metal castings.

  12. Physical and chemical limnology of Ides Cove near Rochester, New York, 1970-1982

    Science.gov (United States)

    Bubeck, R.C.; Staubitz, W.W.; Weidemann, A.D.; Spittal, L.P.

    1995-01-01

    Ides Cove is a small embayment on the western shore of Irondequoit Bay near Rochester, N.Y. In 1982, alum was applied to the cove to seal the bottom sediments and thereby decrease nutrient fluxes in an effort to assess the applicability of this technique to Irondequoit Bay. Published data were used to develop a baseline analysis of the chemical and physical limnology of Ides Cove prior to the alum treatment and to provide a basis for comparison and evaluation of post-treatment data. The baseline analysis also enables evaluation of trends in the nutrient status and mixing patterns in Ides Cove since the decrease of sewage inflows and use of road salt in the Irondequoit Bay and Ides Cove drainage basins during 1970-82. Data from 1970-72 and 1979-82 were used to construct partial and full-year depth profiles of several physical properties and chemical constituents of water in the cove; comparison of these profiles indicates a significant improvement in water quality between 1970 and 1982. The diversion of sewage out of the Irondequoit Creek drainage basin in the late 1970's resulted in an 80-percent decrease in total phosphate concentration and a 50- to 60-percent decrease in nitrogen (nitrate and ammonia) concentration in the cove. Indications of decreased primary productivity are associated with these lowered nutrient concentrations. Summer Secchi-disk transparency increased from 0.6 m (meters) in 1970-72 to 1.2 m in 1980-82; peak epilimnetic dissolved oxygen levels decreased from a range of 22 to 28 mg/L (milligrams per liter) to a range of 16 to 20 mg/L; and peak epilimnetic pH decreased from greater than 9.4 to between 8.8 and 9.0. The decrease in the use of road salt in the Irondequoit basin beginning in 1974 resulted in a decrease in chloride concentration and gradient (difference between the surface and bottom con- centration). The maximum annual chloride concentration in the epilimnion decreased from the 210-to-225-mg/L range in the spring of 1971-72 to the

  13. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Pauul J. Tikalsky

    2004-10-31

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: (1) a statistically sound evaluation of the characterization of foundry sand, (2) a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and (3) the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at N{sub ini}, N{sub des}, and N{sub max}. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  14. Excess Foundry Sand Characterization and Experimental Investigation in Controlled Low-Strength Material and Hot-Mixing Asphalt

    Energy Technology Data Exchange (ETDEWEB)

    Tikalsky, Paul J. [Pennsylvania State Univ., University Park, PA (United States); Bahia, Hussain U. [Univ. of Wisconsin, Madison, WI (United States); Deng, An [Pennsylvania State Univ., University Park, PA (United States); Snyder, Thomas [Univ. of Wisconsin, Madison, WI (United States)

    2004-10-15

    This report provides technical data regarding the reuse of excess foundry sand. The report addresses three topics: a statistically sound evaluation of the characterization of foundry sand, a laboratory investigation to qualify excess foundry sand as a major component in controlled low-strength material (CLSM), and the identification of the best methods for using foundry sand as a replacement for natural aggregates for construction purposes, specifically in asphalt paving materials. The survival analysis statistical technique was used to characterize foundry sand over a full spectrum of general chemical parameters, metallic elements, and organic compounds regarding bulk analysis and leachate characterization. Not limited to characterization and environmental impact, foundry sand was evaluated by factor analyses, which contributes to proper selection of factor and maximization of the reuse marketplace for foundry sand. Regarding the integration of foundry sand into CLSM, excavatable CLSM and structural CLSM containing different types of excess foundry sands were investigated through laboratory experiments. Foundry sand was approved to constitute a major component in CLSM. Regarding the integration of foundry sand into asphalt paving materials, the optimum asphalt content was determined for each mixture, as well as the bulk density, maximum density, asphalt absorption, and air voids at Nini, Ndes, and Nmax. It was found that foundry sands can be used as an aggregate in hot-mix asphalt production, but each sand should be evaluated individually. Foundry sands tend to lower the strength of mixtures and also may make them more susceptible to moisture damage. Finally, traditional anti-stripping additives may decrease the moisture sensitivity of a mixture containing foundry sand, but not to the level allowed by most highway agencies.

  15. Specificity of SPC Procedures Application in Foundry in Aspect of Data Acquisition and Data Exploration

    Directory of Open Access Journals (Sweden)

    Ignaszak Z.

    2012-12-01

    Full Text Available The paper presents an analysis of SPC (Statistical Process Control procedures usability in foundry engineering. The authors pay particular attention to the processes complexity and necessity of correct preparation of data acquisition procedures. Integration of SPC systems with existing IT solutions in area of aiding and assistance during the manufacturing process is important. For each particular foundry, methodology of selective SPC application needs to prepare for supervision and control of stability of manufacturing conditions, regarding specificity of data in particular “branches” of foundry production (Sands, Pouring, Metallurgy, Quality.

  16. Creation of Defects Catalogue for Nonconforming Product Identification in the Foundry Organization

    Directory of Open Access Journals (Sweden)

    Andrea Sütőová

    2013-12-01

    Full Text Available The paper deals with system of casting defects classification problematics and creation of defects catalogue in the foundry organization. There is described the value of correct defects classification and identification in the literature review and also some tools for defects classification are mentioned. Existing defects classifications and catalogues are often unusable for particular production processes and casting technology. Many foundries therefore create their own defects catalogues. The sample of created catalogue, which classifies and describes defects occuring in the aluminium foundry organization and its benefits are presented in the paper. The created catalogue primarily serves as a visual support for production operators and quality control processes.

  17. Wastes Characterisation from Foundry Activities on European Level

    International Nuclear Information System (INIS)

    Andres, I.; Ruiz, C.; Ibanez, R.; Viguri, J.; Irabien, A.

    1999-01-01

    This work presents The results of the eco toxicological characterisation of 22 defined wastes from steel foundry activities. The wastes have been selected from three processes, steel mill (smelting). sand casting and cleaning and finishing of steel products,with the common characteristics of represent an important industrial activity in the area and generated the wastes considered in this study. The eco toxicological characterisation obtained applying the Spanish regulations on hazardous waste is compared to the hazardous attributions considered by the European Union in order to characterise a waste as hazardous (non hazardous). The results allow to conclude that a acceptable concordance between both methodologies is reached and remark the need to split the broad generic types of wastes given by the Spanish regulation (Eco toxic / non eco toxic) into clearly identifiable specific types of waste

  18. Radiometric measurement techniques in metallurgy and foundry technology

    International Nuclear Information System (INIS)

    1990-01-01

    The contributions contain informations concerning the present state and development of radiometric measurement techniques in metallurgy and foundry technology as well as their application to the solution of various problems. The development of isotope techniques is briefly described. Major applications of radiometric equipment in industrial measurement are presented together with the use of isotopes to monitor processes of industrial production. This is followed by a short description of numerous laboratory-scale applications. Another contribution deals with fundamental problems and methods of moisture measurement by neutrons. A complex moisture/density measurement device the practical applicability of which has been tested is described here. Possibilities for clay determination in used-up moulding materials are discussed in a further contribution. The clay content can be determined by real-time radiometric density measurement so that the necessary moisture or addition of fresh sand can be controlled. (orig.) With 20 figs., 9 tabs., 178 refs [de

  19. Laboratories for the 21st Century: Case Studies, Molecular Foundry, Berkeley, California

    Energy Technology Data Exchange (ETDEWEB)

    2010-11-01

    This case study provides information on the Molecular Foundry, which incorporates Labs21 principles in its design and construction. The design includes many of the strategies researched at Lawrence Berkeley Laboratory for energy efficient cleanroom and data centers.

  20. Administrative Record Index for SMA 4 - Former Chemical Plant and SMA 5 - Former Pig Iron Foundry

    Science.gov (United States)

    The Administrative Record Index lists the documents, data and other technical information that the EPA - Region 4 considered in preparing the Statement of Basis for the Former Chemical Plant and the Former Pig Iron Foundry at ERP Compliant Coke.

  1. Implementation KMES Quality system for acquisition and processing data in chosen foundry

    Directory of Open Access Journals (Sweden)

    R. Sika

    2008-08-01

    Full Text Available In the paper, main assumptions, algorithms and functions of author’s KMES Quality system are discussed. Its working version is tested in chosen foundry by near 2 years. This system is applied to enlarge the use of chosen technological data accessible during foundry processes. The data can be introduced by means of keyboard directly in the fields (windows present on the PC screen according to program commands, instead of report-manuscripts containing measured results, or from the automated measurement recording system by direct data import to KMES Quality system. In the paper, a way of technological data acquisition with their further integration into main foundry databases and their processing, with taking into consideration e.g. kind of casting assortment, current time, sequences of measurements, are presented. Also the capabilities of linking KMES Quality system with SAP R/3 system existing in this foundry useful to quality assurance is show.

  2. ESTIMATION OF WORKING CONDITIONS OF FOUNDRY WORKERS BY INFRARED (HEAT RADIATION

    Directory of Open Access Journals (Sweden)

    A. M. Lazarenkov

    2010-01-01

    Full Text Available The description of infrared radiations, their influence on human organism is given. The results of investigation of infrared (heat radiation intensity on the workers in foundries are given.

  3. Tributyltin in environmental samples from the Former Derecktor Shipyard, Coddington Cove, Newport RI

    Energy Technology Data Exchange (ETDEWEB)

    Wade, Terry L.; Sweet, Stephen T.; Quinn, James G.; Cairns, Robert W.; King, John W

    2004-05-01

    Tributyltin (TBT) was detected in all 24 surface sediment (top 2 cm) samples collected from Coddington Cove, Newport, RI. TBT surface sediment concentrations ranged from 32 to 372 ng Sn/g with a mean concentration of 146 ng Sn/g. Analyses of selected core sections detected TBT in at least the top 18 cm at all 7 stations where cores were collected. No consistent TBT concentration trends with depth for these cores suggest mixing is an important process in the sediment column. In one core (station 28), TBT was found in the 76-86 cm section at a concentration of 141 ng Sn/g; thus sediments are a significant sink for TBT. However, sediment mixing processes can enhance releases of bioavailable TBT. Mussels, clams and fish from Coddington Cove contain TBT at concentrations ranging from 9.2 to 977 ng Sn/g. TBT concentrations in lobsters were below the detection limit (<6 ng Sn/g). Based on available screening criteria, TBT concentrations in Coddington Cove sediment is likely to be having an adverse effect on the biota at some locations. - TBT is likely to continue to be bioavailable for many years.

  4. Tributyltin in environmental samples from the Former Derecktor Shipyard, Coddington Cove, Newport RI

    International Nuclear Information System (INIS)

    Wade, Terry L.; Sweet, Stephen T.; Quinn, James G.; Cairns, Robert W.; King, John W.

    2004-01-01

    Tributyltin (TBT) was detected in all 24 surface sediment (top 2 cm) samples collected from Coddington Cove, Newport, RI. TBT surface sediment concentrations ranged from 32 to 372 ng Sn/g with a mean concentration of 146 ng Sn/g. Analyses of selected core sections detected TBT in at least the top 18 cm at all 7 stations where cores were collected. No consistent TBT concentration trends with depth for these cores suggest mixing is an important process in the sediment column. In one core (station 28), TBT was found in the 76-86 cm section at a concentration of 141 ng Sn/g; thus sediments are a significant sink for TBT. However, sediment mixing processes can enhance releases of bioavailable TBT. Mussels, clams and fish from Coddington Cove contain TBT at concentrations ranging from 9.2 to 977 ng Sn/g. TBT concentrations in lobsters were below the detection limit (<6 ng Sn/g). Based on available screening criteria, TBT concentrations in Coddington Cove sediment is likely to be having an adverse effect on the biota at some locations. - TBT is likely to continue to be bioavailable for many years

  5. The Food Web of Potter Cove (Antarctica): complexity, structure and function

    Science.gov (United States)

    Marina, Tomás I.; Salinas, Vanesa; Cordone, Georgina; Campana, Gabriela; Moreira, Eugenia; Deregibus, Dolores; Torre, Luciana; Sahade, Ricardo; Tatián, Marcos; Barrera Oro, Esteban; De Troch, Marleen; Doyle, Santiago; Quartino, María Liliana; Saravia, Leonardo A.; Momo, Fernando R.

    2018-01-01

    Knowledge of the food web structure and complexity are central to better understand ecosystem functioning. A food-web approach includes both species and energy flows among them, providing a natural framework for characterizing species' ecological roles and the mechanisms through which biodiversity influences ecosystem dynamics. Here we present for the first time a high-resolution food web for a marine ecosystem at Potter Cove (northern Antarctic Peninsula). Eleven food web properties were analyzed in order to document network complexity, structure and topology. We found a low linkage density (3.4), connectance (0.04) and omnivory percentage (45), as well as a short path length (1.8) and a low clustering coefficient (0.08). Furthermore, relating the structure of the food web to its dynamics, an exponential degree distribution (in- and out-links) was found. This suggests that the Potter Cove food web may be vulnerable if the most connected species became locally extinct. For two of the three more connected functional groups, competition overlap graphs imply high trophic interaction between demersal fish and niche specialization according to feeding strategies in amphipods. On the other hand, the prey overlap graph shows also that multiple energy pathways of carbon flux exist across benthic and pelagic habitats in the Potter Cove ecosystem. Although alternative food sources might add robustness to the web, network properties (low linkage density, connectance and omnivory) suggest fragility and potential trophic cascade effects.

  6. Feasibility for development of an aquaculture facility at Hot Spring Cove

    Energy Technology Data Exchange (ETDEWEB)

    1986-01-01

    This report describes the feasibilty of obtaining geothermally warmed water for use in aquaculture at Hot Springs Cove, British Columbia, and concludes that while the sources can probably be assessed from two sites in the cove, neither this nor the quantity of water available can be known for certain without field trials. The report also examines the feasibility of culturing various species of sea life at Hot Springs Cove, and concludes that a combination of rearing coho salmon smolts and oysters, with the late addition of tilapia, appears to be the most suitable both for biological and economic reasons. The total capital investment amounts to about $1,033,000. Operating costs would be about $450,000 annually, and additional capital to cover this would be needed in the first years of operation. A business plan is provided which includes cash flow projections for the first nine years of operation, and this shows that a maximum investment of approximately $1.2 million would be needed by the third year of operation. If sufficient warm water is available, and the facility is operated successfully, it should pay off the investment in seven to nine years, provided that interest free loans are available for capital investments. 20 refs., 1 fig., 8 tabs.

  7. Barriers to and drivers for energy efficiency in the Swedish foundry industry

    International Nuclear Information System (INIS)

    Rohdin, Patrik; Thollander, Patrik; Solding, Petter

    2007-01-01

    Despite the need for increased industrial energy efficiency, studies indicate that cost-efficient energy conservation measures are not always implemented, explained by the existence of barriers to energy efficiency. This paper investigates the existence of different barriers to and driving forces for the implementation of energy efficiency measures in the energy intensive Swedish foundry industry. The overall results from a questionnaire show that limited access to capital constitutes by far the largest barrier to energy efficiency according to the respondents. A comparison between group-owned and privately owned foundries shows that, except for limited access to capital, they face different high-ranked barriers. While barriers within group owned companies are more related to organizational problems, barriers within private foundries are more related to information problems. This study also found that energy consultants or other actors working with energy issues in foundries are of major importance in overcoming the largest barriers, as the foundries consider them trustworthy. They may thus help the foundries overcome organizational problems such as lack of sub-metering and lack of budget funds by quantifying potential energy efficiency investments. The two, by far, most important drivers were found to be people with real ambition and long-term energy strategies

  8. Identification of Significant Impact of Silicon Foundry Sands Mining on LCIA

    Directory of Open Access Journals (Sweden)

    Jozef Mitterpach

    2015-12-01

    Full Text Available This paper presents a case study based on a LCA (Life Cycle Assessment research program of the silicon foundry sand (SFS due to the large quantity of produced waste foundry sand (WFS. The foundry waste is a high priority sector within the growing European foundry industry. It is necessary to understand the full life cycle of the foundry waste in order to correctly identify magnitude and types of impacts it has on the environment. System boundary includes the processes: mining, modification, packing, storage and transport to foundry. Inventory analysis data were analyzed and finally converted to the functional unit, which has been defined as one ton of SFS. The resulting environmental impact of SFS production in endpoint is: consumption of natural resources 70.9%, ecosystem quality 18.2% and human health 10.9%. The following portions, with respective percentages, have the greatest overall effect on these results: diesel fuel consumption 32.4% and natural gas consumption 28.7%, electricity usage 17.2%, transport 12.2%, devastation caused by the SFS 5.35% and oil (engine, gear and hydraulic consumption 4.14%. The highest contributor to the diesel fuel consumption is the SFS exploitation. The overall effect of desiccation was 35.8% and was caused by high consumption of resources and electricity.

  9. Modelling and Optimization of Organization of Workplaces in a Foundry

    Directory of Open Access Journals (Sweden)

    Kukla S.

    2016-09-01

    Full Text Available The paper presents a practical example of improvement of foundry production systems in terms of post-finishing of nodular iron castings produced in the conditions of bulk production for automotive industry. The attention was paid to high labour-intensive efforts, which are difficult to be subjected to mechanization and automation. The times of actions related to grinding processing of castings in three grinding positions connected with a belt conveyor were estimated with the use of a time study method. A bottleneck as well as limiting factors were specified in a system. A number of improvements were proposed, aimed at improving work organization on the castings post-finishing line. An analysis of work ergonomics at the workplace was made in order to eliminate unnecessary and onerous for the employee actions. A model of production system using the Arena software, on which a simulation experiment was conducted, was drawn up in order to visualize the analysed phenomena. The effects of the project were shown on graphs comparing times, costs, work ergonomics and overall efficiency of production equipment indicator.

  10. Biopolimers – structure, properties and applicability in the foundry industry

    Directory of Open Access Journals (Sweden)

    B. Grabowska

    2008-04-01

    Full Text Available A review of literature data concerning physicochemical properties and possibilities of practical utilisation of the most important natural biopolymers (proteins, celluloses, starch, chitozan are presented in the paper. Biopolymers being renewable natural polymers characterised by several required physicochemical properties (adhesivity, activity, no toxicity, biodegradability constitute more and more interesting processing raw material for various industrial utilisations including environment friendly binding agents for moulding sands. Protein and starch compositions are used as binding agents for moulding and core sands in the foundry industry. Preliminary tests – performed within own research - of modification and utilisation of biopolymers as binding agents for moulding sands are promising from many aspects: technological (adequate properties of moulding sands, ecological (no toxicity, biodegradability and economic (low price. Starch from the polysaccharide group seems to be especially interesting since it is abundant, easily obtainable, biodegradable and the cheapest polymer. At its actual low price and the possibility of using agricultural wastes in the production, problem of utilising starch in many industry branches can become significant, especially in Poland.

  11. Sustainability innovation foundry - FY13: Merging research and operations

    Energy Technology Data Exchange (ETDEWEB)

    Mizner, Jack Harry [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Passell, Howard David [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Keller, Elizabeth James Kistin [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Gordon, Margaret Ellen [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); McNeish, Jerry A. [Sandia National Laboratories, Livermore, CA (United States); Sullivan, Kristina [Sandia National Laboratories, Livermore, CA (United States)

    2013-12-01

    Sustainability is a critical national security issue for the U.S. and other nations. Sandia National Laboratories (SNL) is already a global leader in sustainability science and technology (SS&T) as documented in this report. This report documents the ongoing work conducted this year as part of the Sustainability Innovation Foundry (SIF). The efforts of the SIF support Sandia's national and international security missions related to sustainability and resilience revolving around energy use, water use, and materials, both on site at Sandia and externally. The SIF leverages existing Sandia research and development (R&D) in sustainability science and technology to support new solutions to complex problems. The SIF also builds on existing Sandia initiatives to support transformation of Sandia into a fully sustainable entity in terms of materials, energy, and water use. In the long term, the SIF will demonstrate the efficacy of sustainability technology developed at Sandia through prototyping and test bed approaches and will provide a common platform for support of solutions to the complex problems surrounding sustainability. Highlights from this year include the Sustainability Idea Challenge, improvements in facilities energy use, lectures and presentations from relevant experts in sustainability [Dr. Barry Hughes, University of Denver], and significant development of the Institutional Transformation (IX) modeling tools to support evaluation of proposed modifications to the SNL infrastructure to realize energy savings.

  12. Freshwater and Saline Loads of Dissolved Inorganic Nitrogen to Hood Canal and Lynch Cove, Western Washington

    Science.gov (United States)

    Paulson, Anthony J.; Konrad, Christopher P.; Frans, Lonna M.; Noble, Marlene; Kendall, Carol; Josberger, Edward G.; Huffman, Raegan L.; Olsen, Theresa D.

    2006-01-01

    Hood Canal is a long (110 kilometers), deep (175 meters) and narrow (2 to 4 kilometers wide) fjord of Puget Sound in western Washington. The stratification of a less dense, fresh upper layer of the water column causes the cold, saltier lower layer of the water column to be isolated from the atmosphere in the late summer and autumn, which limits reaeration of the lower layer. In the upper layer of Hood Canal, the production of organic matter that settles and consumes dissolved oxygen in the lower layer appears to be limited by the load of dissolved inorganic nitrogen (DIN): nitrate, nitrite, and ammonia. Freshwater and saline loads of DIN to Hood Canal were estimated from available historical data. The freshwater load of DIN to the upper layer of Hood Canal, which could be taken up by phytoplankton, came mostly from surface and ground water from subbasins, which accounts for 92 percent of total load of DIN to the upper layer of Hood Canal. Although DIN in rain falling on land surfaces amounts to about one-half of the DIN entering Hood Canal from subbasins, rain falling directly on the surface of marine waters contributed only 4 percent of the load to the upper layer. Point-source discharges and subsurface flow from shallow shoreline septic systems contributed less than 4 percent of the DIN load to the upper layer. DIN in saline water flowing over the sill into Hood Canal from Admiralty Inlet was at least 17 times the total load to the upper layer of Hood Canal. In September and October 2004, field data were collected to estimate DIN loads to Lynch Cove - the most inland marine waters of Hood Canal that routinely contain low dissolved-oxygen waters. Based on measured streamflow and DIN concentrations, surface discharge was estimated to have contributed about one-fourth of DIN loads to the upper layer of Lynch Cove. Ground-water flow from subbasins was estimated to have contributed about one-half of total DIN loads to the upper layer. In autumn 2004, the relative

  13. Energy efficiency opportunities in the production process of cast iron foundries: An experience in Italy

    International Nuclear Information System (INIS)

    Lazzarin, Renato M.; Noro, Marco

    2015-01-01

    Foundry sector is one of the most energy intensive in industry. Energy audits performed in 5 Italian cast iron foundries allowed to identify energy utilization in the various processes that from the melting of the iron arrive at the finishing of the casting. Main equipment was surveyed, evaluating the influence on the overall energy consumption, producing a detailed analysis of energy use per department and energy performance indexes. A separate study was carried out for foundries with induction furnaces and cold or hot blast cupolas. Possibilities of heat recovery was identified particularly in combustion air preheating, but also for building heating or to power direct cycles to produce electricity. Better insulation and new insulating materials can improve the efficiency and the quality of the processes. Suggestions are supplied in the various foundry departments for energy saving. Possible energy saving actions on the service plants will be dealt with in a separate paper. - Highlights: • The Authors performed energy audits in 5 Italian cast iron foundries. • Main equipment was surveyed, evaluating the influence on the overall energy consumption. • An analysis of energy use per department and energy performance indexes was performed. • Possibilities of heat recovery were identified in combustion air preheating and for building heating. • Better and new insulating materials were analyzed to improve the efficiency and process quality.

  14. COVE-1: a finite difference creep collapse code for oval fuel pin cladding material

    International Nuclear Information System (INIS)

    Mohr, C.L.

    1975-03-01

    COVE-1 is a time-dependent incremental creep collapse code that estimates the change in ovality of a fuel pin cladding tube. It uses a finite difference method of solving the differential equations which describe the deflection of the tube walls as a function of time. The physical problem is nonlinear, both with respect to geometry and material properties, which requires the use of an incremental, analytical, path-dependent solution. The application of this code is intended primarily for tubes manufactured from Zircaloy. Therefore, provision has been made to include some of the effects of anisotropy in the flow equations for inelastic incremental deformations. 10 references. (U.S.)

  15. Diatoms of the marine littoral of Steenberg's cove in St. Helena Bay, Cape province, South Africa

    CSIR Research Space (South Africa)

    Malcolm, HG

    1973-01-01

    Full Text Available transapical striae in 10 ~m. It is easily overlooked and though recorded in the samples as infrequent may be more abundant. Dimensions of the Steenberg?s Cove material were 8?10 1zm long, 3 jzm broad, striae 27 in 10 1cm. ? 619, 620. A. proteus GREGORY... (cf. CLEVE 1895: 103; GIFFEN 1970a, 267, Fig. 19). Always rare in the material. ? 619, 620. A. proteus var. coutigna CLEVE (cf. GIFFEN 1971 a, 3). As stated in a previous paper the author doubts whether these varieties viz. var. conti,gua CLEVE...

  16. Simulation by the method of inverse cumulative distribution function applied in optimising of foundry plant production

    Directory of Open Access Journals (Sweden)

    J. Szymszal

    2009-01-01

    Full Text Available The study discusses application of computer simulation based on the method of inverse cumulative distribution function. The simulationrefers to an elementary static case, which can also be solved by physical experiment, consisting mainly in observations of foundryproduction in a selected foundry plant. For the simulation and forecasting of foundry production quality in selected cast iron grade, arandom number generator of Excel calculation sheet was chosen. Very wide potentials of this type of simulation when applied to theevaluation of foundry production quality were demonstrated, using a number generator of even distribution for generation of a variable ofan arbitrary distribution, especially of a preset empirical distribution, without any need of adjusting to this variable the smooth theoreticaldistributions.

  17. Drying of water based foundry coatings: Innovative test, process design and optimization methods

    DEFF Research Database (Denmark)

    Di Muoio, Giovanni Luca; Johansen, Bjørn Budolph

    on real industrial cases. These tools have been developed in order to simulate and optimize the drying process and reduce drying time and power consumption as well as production process design time and cost of expensive drying equipment. Results show that test methods from other industries can be used...... capacity goals there is a need to understand how to design, control and optimize drying processes. The main focus of this project was on the critical parameters and properties to be controlled in production in order to achieve a stable and predictable drying process. We propose for each of these parameters...... of Denmark with the overall aim to optimize the drying process of water based foundry coatings. Drying of foundry coatings is a relatively new process in the foundry industry that followed the introduction of water as a solvent. In order to avoid moisture related quality problems and reach production...

  18. Comparison of Energy Consumption in the Classical (PID and Fuzzy Control of Foundry Resistance Furnace

    Directory of Open Access Journals (Sweden)

    Ziółkowskia E.

    2012-09-01

    Full Text Available Foundry resistance furnaces are thermal devices with a relatively large time delay in their response to a change in power parameters. Commonly used in automation classical PID controllers do not meet the requirements of high-quality control. Developed in recent years, fuzzy control theory is increasingly being used in various branches of economy and industry. Fuzzy controllers allow to introduce new developments in control systems of foundry furnaces as well. Correctly selected fuzzy controller can significantly reduce energy consumption in a controlled thermal process of heating equipment. The article presents a comparison of energy consumption by control system of foundry resistance furnace, equipped with either a PID controller or fuzzy controller optimally chosen.

  19. Prevention of occupational injuries: Evidence for effective good practices in foundries.

    Science.gov (United States)

    Porru, Stefano; Calza, Stefano; Arici, Cecilia

    2017-02-01

    Occupational injuries are a relevant research and practical issue. However, intervention studies evaluating the effectiveness of workplace injury prevention programs are seldom performed. The effectiveness of a multifaceted intervention aimed at reducing occupational injury rates (incidence/employment-based=IR, frequency/hours-based=FR, severity=SR) was evaluated between 2008 and 2013 in 29 Italian foundries (22 ferrous; 7 non-ferrous; 3,460 male blue collar workers/year) of varying sizes. Each foundry established an internal multidisciplinary prevention team for risk assessment, monitoring and prevention of occupational injuries, involving employers, occupational physicians, safety personnel, workers' representatives, supervisors. Targets of intervention were workers, equipment, organization, workplace, job tasks. An interrupted time series (ITS) design was applied. 4,604 occupational injuries and 83,156 lost workdays were registered between 2003 and 2013. Statistical analysis showed, after intervention, a reduction of all injury rates (-26% IR, -15% FR, -18% SR) in ferrous foundries and of SR (-4%) in non-ferrous foundries. A significant (p=0.021) 'step-effect' was shown for IR in ferrous foundries, independent of secular trends (pgood external validity; promotion of effective good practices. Main limitations were the non-randomized nature and a medium length post-intervention period. In conclusion, a multifaceted, pragmatic and accountable intervention is effective in reducing the burden of occupational injuries in small-, medium- and large-sized foundries. Practical Applications: The study poses the basis for feasible good practice guidelines to be implemented to prevent occupational injuries, by means of sector-specific numerical benchmarks, with potentially relevant impacts on workers, companies, occupational health professionals and society at large. Copyright © 2016 National Safety Council and Elsevier Ltd. All rights reserved.

  20. Technologies for decreasing the tap temperature to save energy in steel foundries

    Science.gov (United States)

    Biswas, Siddhartha

    Steel foundries are one of the most energy intensive industries. The increasing concerns over volatile energy cost and carbon dioxide emission have pushed foundries to improve efficiency and hence decrease electrical energy consumption. Statistical analysis of industrial survey data was combined with computational fluid dynamics (CFD) modeling to investigate the best industrial practices and opportunities to improve energy efficiency. Reducing tap temperature was identified as one of the important ways of reducing energy consumption. Steel foundries typically tap at 1650-1800°C (3000-3300°F) which is 100-250°C (150-450°F) higher than the pouring temperature. The steel temperature is elevated to compensate for the temperature loss associated with tapping, holding and transporting the liquid steel from the furnace to the pouring floor. Based on experimental investigations and CFD modeling of heat losses during holding in the ladle for different foundry practices, a spreadsheet calculator has been developed to calculate the optimum tap temperature for the specific foundry practices which will eliminate unnecessary superheating. The calculated results were compared and validated with industrial measurements. Improving the lining refractory is one significant way of reducing heat losses during holding of the steel in ladle. Silica sand linings are being used in steel foundries as an inexpensive and convenient material for short holding times and small volumes. The possibilities of improvements of silica sand linings by the addition of lower density cenospheres (hollow spheres), a byproduct of coal fired power plants, was studied through property measurements and laboratory trials.

  1. Optimization of casting defects analysis with supply chain in cast iron foundry process

    Directory of Open Access Journals (Sweden)

    C. Narayanaswamy

    2016-10-01

    Full Text Available Some of the foundries are in need of meeting production targets and due to the urgency they ignore the rejections. The objective of this paper is to analyze the various defects, [1] from molding process in a cast iron foundry. The Failure Mode Effects Analysis (FMEA in quality control [2-6] with suitable supply chain for mold making process considering rejection rates are identified and analyzed in terms of Risk Priority Number (RPN to prioritize the attention for each of the problem. The optimum levels of selected parameters [7] are obtained in this analysis.

  2. Using sol-gel component as additive to foundry coatings to improve casting quality

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Poulsen, T.; Gravesen, B.

    2012-01-01

    The improvement of foundry coatings to enhance performance is important. This paper investigates the effect of using sol‐gel component as an additive to foundry coatings applied on chemically bonded sand cores. Three parameters at three levels each were investigated using Taguchi experimental...... was evaluated. The results show that the surface quality of castings obtained by adding the sol‐gel component to the coatings for cold box cores has no significant difference from castings produced with coatings without sol‐gel component. On the other hand, the addition of the sol‐gel component in coatings...

  3. Locating inputs of freshwater to Lynch Cove, Hood Canal, Washington, using aerial infrared photography

    Science.gov (United States)

    Sheibley, Rich W.; Josberger, Edward G.; Chickadel, Chris

    2010-01-01

    The input of freshwater and associated nutrients into Lynch Cove and lower Hood Canal (fig. 1) from sources such as groundwater seeps, small streams, and ephemeral creeks may play a major role in the nutrient loading and hydrodynamics of this low dissolved-oxygen (hypoxic) system. These disbursed sources exhibit a high degree of spatial variability. However, few in-situ measurements of groundwater seepage rates and nutrient concentrations are available and thus may not represent adequately the large spatial variability of groundwater discharge in the area. As a result, our understanding of these processes and their effect on hypoxic conditions in Hood Canal is limited. To determine the spatial variability and relative intensity of these sources, the U.S. Geological Survey Washington Water Science Center collaborated with the University of Washington Applied Physics Laboratory to obtain thermal infrared (TIR) images of the nearshore and intertidal regions of Lynch Cove at or near low tide. In the summer, cool freshwater discharges from seeps and streams, flows across the exposed, sun-warmed beach, and out on the warm surface of the marine water. These temperature differences are readily apparent in aerial thermal infrared imagery that we acquired during the summers of 2008 and 2009. When combined with co-incident video camera images, these temperature differences allow identification of the location, the type, and the relative intensity of the sources.

  4. Groundwater flow code verification ''benchmarking'' activity (COVE-2A): Analysis of participants' work

    International Nuclear Information System (INIS)

    Dykhuizen, R.C.; Barnard, R.W.

    1992-02-01

    The Nuclear Waste Repository Technology Department at Sandia National Laboratories (SNL) is investigating the suitability of Yucca Mountain as a potential site for underground burial of nuclear wastes. One element of the investigations is to assess the potential long-term effects of groundwater flow on the integrity of a potential repository. A number of computer codes are being used to model groundwater flow through geologic media in which the potential repository would be located. These codes compute numerical solutions for problems that are usually analytically intractable. Consequently, independent confirmation of the correctness of the solution is often not possible. Code verification is a process that permits the determination of the numerical accuracy of codes by comparing the results of several numerical solutions for the same problem. The international nuclear waste research community uses benchmarking for intercomparisons that partially satisfy the Nuclear Regulatory Commission (NRC) definition of code verification. This report presents the results from the COVE-2A (Code Verification) project, which is a subset of the COVE project

  5. Hydrogen and acetate cycling in two sulfate-reducing sediments: Buzzards Bay and Town Cove, Massachusetts

    Energy Technology Data Exchange (ETDEWEB)

    Novelli, P.C. (SUNY, Stony Brook, NY (USA) Univ. of Colorado, Boulder (USA)); Michelson, A.R.; Scranton, M.I. (SUNY, Stony Brook, NY (USA)); Banta, G.T.; Hobbie, J.E. (Marine Biological Laboratory, Woods, Hole, MA (USA)); Howarth, R.W. (Cornell Univ., Ithaca, NY (USA))

    1988-10-01

    Molecular hydrogen and acetate are believed to be key intermediates in the anaerobic remineralization of organic carbon. The authors have made measurements of the cycling of both these compounds in two marine sediments: the bioturbated sediments of Buzzards Bay, Mass., and the much more reducing sediments of Town Cove, Orleans, Mass. Hydrogen concentrations are similar in these environments (from less than 5 to 30 nM), and are within the range previously reported for coastal sediments. However, apparent hydrogen production rates differ by a factor of 60 between these two sediments and at both sites show strong correlation with measured rates of sulfate reduction. Acetate concentrations generally increased with depth in both environments; this increase was greater in Buzzards Bay (22.5 to 71.5 {mu}M) than in Town Cove (26 to 44 {mu}M). Acetate oxidation rates calculated from measured concentrations and {sup 14}C-acetate consumption rate constants suggest that the measured acetate was not all available to sulfate-reducing bacteria. Using the measured sulfate reduction rates, they estimate that between 2% and 100% of the measured acetate pool is biologically available, and that the bioavailable pool decreases with depth. A diagenetic model of the total acetate concentration suggests that consumption may be first order with respect to only a fraction of the total pool.

  6. The study of heavy metals leaching from waste foundry sands using a one-step extraction

    Science.gov (United States)

    Bożym, Marta

    2017-10-01

    There are a number of leaching test which are used to evaluate the effect of foundry waste disposal on the environment (TCLP, SPLP, ASTM at al.). Because the spent foundry sand are usually deposited at the ground level and they have a similar structure to the soil, survey mobility of metals using the same methods seems appropriate. One-step extraction allows for the evaluation of the mobility and bioavailability of metals in soil and waste. Waste foundry sands have been successfully used as a component in manufactured soils in U.S., but concern over metal contamination must be eliminated before considering this direction of use. The study evaluated the leaching of heavy metals (Cd, Pb, Cu, Zn, Cr, Ni) from deposited waste foundry sands. The overall, as well as heavy metals were extracted by different type of extractants: H2O, CH3COOH, HCl, EDTA, MgCl2 and NaCOOH. These extractants are most commonly used to study the mobility and bioavailability of metals in soil and waste. In the present study applicable standards and methodology described in the literature in analysis were used. The results allowed to evaluate the bioavailability of metals leached from those wastes.

  7. Risk assessment of chemicals in foundries: The International Chemical Toolkit pilot-project

    International Nuclear Information System (INIS)

    Ribeiro, Marcela G.; Filho, Walter R.P.

    2006-01-01

    In Brazil, problems regarding protection from hazardous substances in small-sized enterprises are similar to those observed in many other countries. Looking for a simple tool to assess and control such exposures, FUNDACENTRO has started in 2005 a pilot-project to implement the International Chemical Control Toolkit. During the series of visits to foundries, it was observed that although many changes have occurred in foundry technology, occupational exposures to silica dust and metal fumes continue to occur, due to a lack of perception of occupational exposure in the work environment. After introducing the Chemical Toolkit concept to the foundry work group, it was possible to show that the activities undertaken to improve the management of chemicals, according to its concept, will support companies in fulfilling government legislations related to chemical management, occupational health and safety, and environmental impact. In the following meetings, the foundry work group and FUNDACENTRO research team will identify 'inadequate work situations'. Based on the Chemical Toolkit, improvement measures will be proposed. Afterwards, a survey will verify the efficency of those measures in the control of hazards and consequently on the management of chemicals. This step is now in course

  8. Methodology supporting production control in a foundry applying modern DISAMATIC molding line

    Directory of Open Access Journals (Sweden)

    Sika Robert

    2017-01-01

    Full Text Available The paper presents methodology of production control using statistical methods in foundry conditions, using the automatic DISAMATIC molding line. The authors were inspired by many years of experience in implementing IT tools for foundries. The authors noticed that there is a lack of basic IT tools dedicated to specific casting processes, that would greatly facilitate their oversight and thus improve the quality of manufactured products. More and more systems are installed in the ERP or CAx area, but they integrate processes only partially, mainly in the area of technology design and business management from finance and control. Monitoring of foundry processes can generate a large amount of process-related data. This is particularly noticeable in automated processes. An example is the modern DISAMATIC molding line, which integrates several casting processes, such as mold preparation, assembly, pouring or shake out. The authors proposed a methodology that supports the control of the above-mentioned foundry processes using statistical methods. Such an approach can be successfully used, for example, during periodic external audits. The mentioned methodology in the innovative DISAM-ProdC computer tool was implemented.

  9. The study of heavy metals leaching from waste foundry sands using a one-step extraction

    Directory of Open Access Journals (Sweden)

    Bożym Marta

    2017-01-01

    Full Text Available There are a number of leaching test which are used to evaluate the effect of foundry waste disposal on the environment (TCLP, SPLP, ASTM at al.. Because the spent foundry sand are usually deposited at the ground level and they have a similar structure to the soil, survey mobility of metals using the same methods seems appropriate. One-step extraction allows for the evaluation of the mobility and bioavailability of metals in soil and waste. Waste foundry sands have been successfully used as a component in manufactured soils in U.S., but concern over metal contamination must be eliminated before considering this direction of use. The study evaluated the leaching of heavy metals (Cd, Pb, Cu, Zn, Cr, Ni from deposited waste foundry sands. The overall, as well as heavy metals were extracted by different type of extractants: H2O, CH3COOH, HCl, EDTA, MgCl2 and NaCOOH. These extractants are most commonly used to study the mobility and bioavailability of metals in soil and waste. In the present study applicable standards and methodology described in the literature in analysis were used. The results allowed to evaluate the bioavailability of metals leached from those wastes.

  10. Research and application of enterprise resource planning system for foundry enterprises

    Directory of Open Access Journals (Sweden)

    Zhou Jianxin

    2013-01-01

    Full Text Available PPDB issues - four aspects of current management issues of foundry enterprises are discussed in this paper, including Production Management, Process Control, Duration Monitoring and Business Intelligence Data Analysis. Also a whole Enterprise Resource Planning (ERP solution for foundry enterprises is proposed. The solution contains many models, four of which are used to solve the PPDB issues. These are called SPDB models, which separately are the Single-piece management model (based on casting lifecycle, Process management model (based on task-driven technology, Duration monitoring model (based on surplus period, and Business intelligence data analysis model (based on data mining. An ERP system for foundry enterprises, named HZERP, was researched and developed, and applied to a sand casting company of single piece and small batch production. Qualitatively and quantitatively comparing the application effect before and after implementing the HZERP system, the result demonstrated that the foundry ERP system based on the SPDB models can help metal casting enterprises achieve the single-piece management, better regulate the production processes, improve production and delivery management, shorten the production cycle, reduce costs, and speed up the capital turnover to a large extent.

  11. A new low-cost method of reclaiming mixed foundry waste sand based on wet-thermal composite reclamation

    OpenAIRE

    Fan Zitian; Liu Fuchu; Long Wei

    2014-01-01

    A lot of mixed clay-resin waste sand from large-scale iron foundries is discharged every day; so mixed waste sand reclamation in low cost and high quality has a great realistic significance. In the study to investigate the possibility of reusing two types of waste foundry sands, resin bonded sand and clay bonded sand which came from a Chinese casting factory, a new low-cost reclamation method of the mixed foundry waste sand based on the wet-thermal composite reclamation was proposed. The wast...

  12. Persistence, biodegradation and biological impact of Bunker C residues in Black Duck Cove, Nova Scotia

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K.; Wohlgeschaffen, G. D.; Tremblay, G. H. [Dept. of Fisheries and Oceans of Canada, Inst. Maurice-Lamontagne, Mont Joli, PQ (Canada); Vandermeulen, D. C.; Mossman, K. G. [Dept. of Fisheries and Oceans of Canada, Bedford Inst. of Oceanography, Dartmouth, NS (Canada); Doe, K. G.; Jackman, P. M. [Environment Canada, Environmental Science Center, Moncton, NB (Canada); Prince, R. C.; Garrett, R. M.; Haith, C. E. [Exxon Research and Engineering Company, Annandale, NJ (United States)

    1998-12-31

    In 1970, approximately 2,045 cubic metres of Bunker C oil impacted on 300 km of Nova Scotia`s coastline following the grounding of the tanker `Arrow`. Only 10 per cent of the coastline was subjected to cleanup, the remainder was left to degrade naturally. Samples of sediments were collected in 1993 and 1997 in order to assess the attenuation processes on the reduction of toxicity within sediments and interstitial waters at Black Duck Cove, one of the untreated sites where residual oil was clearly evident. Detailed chemical analyses showed that the Bunker C oil at this site has undergone substantial biodegradation. Over the 20 plus years since the oil spill the toxicity of the residual oil has been significantly reduced and there is substantial evidence of habitat recovery.

  13. Persistence, biodegradation and biological impact of Bunker C residues in Black Duck Cove, Nova Scotia

    Energy Technology Data Exchange (ETDEWEB)

    Lee, K.; Wohlgeschaffen, G. D.; Tremblay, G. H. [Dept. of Fisheries and Oceans of Canada, Inst. Maurice-Lamontagne, Mont Joli, PQ (Canada); Vandermeulen, D. C.; Mossman, K. G. [Dept. of Fisheries and Oceans of Canada, Bedford Inst. of Oceanography, Dartmouth, NS (Canada); Doe, K. G.; Jackman, P. M. [Environment Canada, Environmental Science Center, Moncton, NB (Canada); Prince, R. C.; Garrett, R. M.; Haith, C. E. [Exxon Research and Engineering Company, Annandale, NJ (United States)

    1998-07-01

    In 1970, approximately 2,045 cubic metres of Bunker C oil impacted on 300 km of Nova Scotia's coastline following the grounding of the tanker 'Arrow'. Only 10 per cent of the coastline was subjected to cleanup, the remainder was left to degrade naturally. Samples of sediments were collected in 1993 and 1997 in order to assess the attenuation processes on the reduction of toxicity within sediments and interstitial waters at Black Duck Cove, one of the untreated sites where residual oil was clearly evident. Detailed chemical analyses showed that the Bunker C oil at this site has undergone substantial biodegradation. Over the 20 plus years since the oil spill the toxicity of the residual oil has been significantly reduced and there is substantial evidence of habitat recovery.

  14. Differential diagnosis between early repolarization of athlete's heart and coved-type Brugada electrocardiogram.

    Science.gov (United States)

    Zorzi, Alessandro; Leoni, Loira; Di Paolo, Fernando M; Rigato, Ilaria; Migliore, Federico; Bauce, Barbara; Pelliccia, Antonio; Corrado, Domenico

    2015-02-15

    Early repolarization (ER) is typically observed in highly trained athletes as a physiologic consequence of increased vagal tone. The variant of anterior (V1 to V3) ER characterized by "domed" ST-segment elevation and negative T wave raises problems of differential diagnosis with the "coved-type" electrocardiographic pattern seen in Brugada syndrome (BS). This study was designed to identify electrocardiographic criteria for distinguishing athlete's ER from BS. The study compared the electrocardiographic tracings of 61 healthy athletes (80% men, median age 23 ± 8 years), showing "domed" ST-segment elevation and negative T wave in leads V1 to V3, with those of 92 consecutive age- and sex-matched BS patients with a "coved-type" electrocardiographic pattern. The electrocardiographic analysis focused on the ST-segment elevation at J point (STJ) and at 80 milliseconds after J point (ST₈₀). Athletes had a lower maximum amplitude of STJ (1.46 ± 0.7 vs 3.25 ± 0.6 mm, p 1) versus only 2 (3%) athletes (p <0.001). An upsloping ST-segment configuration (STJ/ST₈₀ <1) showed a sensitivity of 97%, a specificity of 100%, and a diagnostic accuracy of 98.7% for the diagnosis of ER. At multivariate analysis, STJ/ST₈₀ ratio remained the only independent predictor for ER (odds ratio 87, 95% confidence interval 19 to 357, p <0.001). In conclusion, the STJ/ST₈₀ ratio is a highly accurate electrocardiographic parameter for differential diagnosis between anterior ER of the athlete and BS. Our results may help in reducing the number of athletes who undergo expensive diagnostic workup or are unnecessarily disqualified from competition for changes that fall within the normal range of athlete's heart. Copyright © 2015 Elsevier Inc. All rights reserved.

  15. Design process optimization, virtual prototyping of manufacturing, and foundry-portable DFM (Invited Paper)

    Science.gov (United States)

    Hogan, James; Progler, Christopher; Chatila, Ahmad; Bruggeman, Bert; Heins, Mitchell; Pack, Robert; Boksha, Victor

    2005-05-01

    We consider modern design for manufacturing (DFM) as a manifestation of IC industry re-integration and intensive cost management dynamics. In that regard DFM is somewhat different from so-called design for yield (DFY) which essentially focuses on productivity (yield) management (that is not to say that DFM and DFY do not have significant overlaps and interactions). We clearly see the shaping of a new "full-chip DFM" infrastructure on the background of the "back to basics" design-manufacturing re-integration dynamics. In the presented work we are focusing on required DFM-efficiencies in a "foundry-fabless" link. Concepts of "virtual prototyping of manufacturing", "design process optimization", and "foundry-portable DFM" models are explored. Both senior management of the industry and leading design groups finally realize the need for a radical change of design styles. Some of the DFM super-goals are to isolate designers from process details and to make designs foundry portable. It requires qualification of designs at different foundries. In their turn, foundries specified and are implementing a set of DFM rules: "action-required", "recommended", and "guidelines" while asking designers to provide netlist and testing information. Also, we observe strong signs of innovation coming back to the mask industry. Powerful solutions are emerging and shaping up toward mask-centered IP as a business. While it seems that pure-play foundries have found their place for now in the "IDM+" model (supporting manufacturing capacity of IDMs) it is not obvious how sustainable the model is. Wafer as a production unit is not sufficient anymore; foundries are being asked by large customers to price products in terms of good die. It brings back the notion of the old ASIC business model where the foundry is responsible for dealing with both random and systematic yield issues for a given design. One scenario of future development would be that some of the leading foundries might eventually

  16. [Comparison of color reappearance between metal-ceram restoration and foundry-ceram restoration using crystaleye spectrophotometer].

    Science.gov (United States)

    Shi, Tao; Zhang, Ning; Kong, Fan-wen; Zhan, De-song

    2010-10-01

    To study the color reappearance effect of metal-ceram restoration and foundry-ceram restoration using Crystaleye spectrophotometer. 58 metal-ceram restorations and 58 foundry-ceram restorations according to the result of the Crystaleye spectrophotometer were made respectively. The deltaE between restorations and natural teeth as referenced were analyzed. And satisfaction of dentists and patients were evaluated. The deltaE between metal-ceram restorations and natural teeth was 7.13 +/- 0.74. The deltaE between foundry-ceram restorations and teeth was 1.47 +/- 0.84. There were statistical differences between the deltaE (P spectrophotometer can provide accurate reference for foundry-ceram restoration, but for metal-ceram restoration it is not accurate.

  17. Applications of the systems theory to the designing of the sand preparation sub-system in foundry plants

    Directory of Open Access Journals (Sweden)

    R. Wrona

    2009-07-01

    Full Text Available This study provides the basic principles for designing the functional structure of manufacturing systems and their components. The analysis of functional values is applied to create the technological and manufacturing model underlying the design of the foundry equipment with machine units and materials handling systems. Quoted examples illustrate the approved procedure to be applied to control the sand preparation process in a foundry.

  18. Investigation into the Heat of Hydration and Alkali Silica Reactivity of Sustainable Ultrahigh Strength Concrete with Foundry Sand

    Directory of Open Access Journals (Sweden)

    Federico Aguayo

    2017-01-01

    Full Text Available This study presents the hydration reactivity and alkali silica reaction (ASR of ultrahigh strength concrete (UHSC that has been made more sustainable by using spent foundry sand. Spent foundry sand not only is sustainable but has supplementary cementitious material (SCM characteristics. Two series of UHSC mixtures were prepared using a nonreactive and reactive sand (in terms of ASR to investigate both the impact of a more reactive aggregate and the use of spent foundry sand. Conduction calorimetry was used to monitor the heat of hydration maintained under isothermal conditions, while ASR was investigated using the accelerated mortar bar test (AMBT. Additionally, the compressive strengths were measured for both series of mixtures at 7, 14, and 28 days to confirm high strength requirements. The compressive strengths ranged from 85 MPa (12,345 psi to 181.78 MPa (26,365 psi. This result demonstrates that a UHSC mixture was produced. The calorimetry results revealed a slight acceleration in the heat of hydration flow curve compared to the control from both aggregates indicating increased hydration reactivity from the addition of foundry waste. The combination of foundry sand and reactive sand was found to increase ASR reactivity with increasing additions of foundry sand up to 30% replacement.

  19. Sessile macro-epibiotic community of solitary ascidians, ecosystem engineers in soft substrates of Potter Cove, Antarctica

    OpenAIRE

    Rimondino, Clara; Torre, Luciana; Sahade, Ricardo Jose; Tatian, Marcos

    2016-01-01

    The muddy bottoms of inner Potter Cove, King George Island (Isla 25 de Mayo), South Shetlands, Antarctica, show a high density and richness of macrobenthic species, particularly ascidians. In other areas, ascidians have been reported to play the role of ecosystem engineers, as they support a significant number of epibionts, increasing benthic diversity. In this study, a total of 21 sessile macro-epibiotic taxa present on the ascidian species Corella antarctica Sluiter, 1905, Cnemidocarpa verr...

  20. Reuse of waste foundry sand through interaction with sodium silicate binder

    International Nuclear Information System (INIS)

    Souza, J.C.; Chinelatto, A.S.A.; Chinelatto, A.L.; Oliveira, I.L.

    2012-01-01

    Green sand molds are used in metal casting process. However, after heating, activated bentonite present in green sand lose the binding properties, and part of the foundry sand has to be discarded from the process. The ABNT NBR 15.984/2011 establishes the management of waste foundry sand (WFS) avoiding disposal in landfills. The objective of this work was to investigate the possibility of reusing the WFS from the study of their interaction with sodium silicate binder. Studies with silica sand and new green sand was performed to compare the results obtained with the WFS. The characterizations of the samples were performed by measures the compressive strength, X-ray diffraction, optical microscopy and scanning electron microscopy. The results showed that there is interaction of the sodium silicate with the WFS as well as with the silica sand and green sand. (author)

  1. EVALUATION OF THE BENTONITE CONTENT IN SPENT FOUNDRY SANDS AS A FUNCTION OF HYDRAULIC CONDUCTIVITY COEFFICIENT

    Directory of Open Access Journals (Sweden)

    Schirlene Chegatti

    2013-06-01

    Full Text Available This study evaluates the relationship of the bentonite content and hydraulic conductivity coefficient (k of waste foundry sands in tests of hydraulic conductivity in a flexible wall permeameter. The test samples had concentrations of activated sodium bentonite and natural sodium bentonite between 4% and 15%. It was also analyzed chemically the liquid leachate (aluminum, barium, chromium, cadmium, lead, phenols, iron, fluoride, and manganese, following de standard tests of Standard Methods 3111 B e D for the determination of this components in liquid samples. The experiments were supplemented with cation exchange capacity analysis. The results indicate that the values of are is related to the content of bentonite in waste foundry sand and the percolation from this waste disposal.

  2. SYNBIOCHEM Synthetic Biology Research Centre, Manchester – A UK foundry for fine and speciality chemicals production

    Directory of Open Access Journals (Sweden)

    Le Feuvre RA

    2016-12-01

    Full Text Available The UK Synthetic Biology Research Centre, SYNBIOCHEM, hosted by the Manchester Institute of Biotechnology at the University of Manchester is delivering innovative technology platforms to facilitate the predictable engineering of microbial bio-factories for fine and speciality chemicals production. We provide an overview of our foundry activities that are being applied to grand challenge projects to deliver innovation in bio-based chemicals production for industrial biotechnology.

  3. Moisture diffusion coefficients determination of furan bonded sands and water based foundry coatings

    DEFF Research Database (Denmark)

    Di Muoio, Giovanni Luca; Tiedje, Niels Skat

    2016-01-01

    Moisture content in furan bonded sand and water based coatings can be one of the main causes for gas related defects in large cast iron parts. Moisture diffusion coefficients for these materials are needed to precisely predict the possible moisture levels in foundry moulds. In this study, we first...... provide an example on how it is possible to apply this knowledge to estimate moisture variation in a sand mould during production....

  4. AN ANALYSIS OF THE DIFFERENTIATION STRATEGIES OF RURAL FOUNDRIES IN THE BEGINNING OF THE 20TH CENTURY IN THE PROVINCE OF QUEBEC

    Directory of Open Access Journals (Sweden)

    Lisa Baillargeon

    2009-01-01

    Full Text Available The business model and strategic position of Quebec's rural foundries at the beginning of the 20th century is virtually unknown. Inferences have been made based on pictorial and oral data sources. This data reveals that successful rural foundries were, in essence, confined to producing and selling agricultural tools to local farmers on an as-needed basis, because large urban foundries were already mass-producing domestic and industrial objects. In contrast, use of detailed accounting records and advertising publications of three rural foundries over the 1900 to 1914 period provides a clearer picture of the production and of the clientele of those rural foundries. Analysis of these sources suggests that the strategic business model of rural foundries was much more elaborate than the existing literature posits. Rural owner-managers of the early 20th century were sophisticated strategists, marketers, and operators.

  5. ELABORATION OF MANAGEMENT PLAN OF SOLID WASTE FROM SMALL CAST IRON FOUNDRIES

    Directory of Open Access Journals (Sweden)

    Carlos Alberto Mendes Moraes

    2013-12-01

    Full Text Available The foundry industry contributes to society meeting the demand of metal scrap recycling, but, at the same time, it brings a high risk of environmental impact for its many potentially pollutant wastes. Among these, there are slag and used foundry sand (cold cure molding. Through a survey about the production process of a small cast iron company, the collected data was compiled to determine the organizational setting in terms of generation and segregation of waste. From a complete environmental diagnosis carried out in eight small cast iron foundries, one of them was chosen to be a basis for the elaboration of an industrial solid waste management plan, which is becoming necessary to know and manage the generation of wastes qualitatively and quantitatively. A data assessment about the production process was carried out and compiled to determine the actual organizational scenario. As a result of that, it is possible to create a favorable environment to develop tools for environmental impacts prevention, which will permit the migration for more complex actions on the direction of more efficient process, cleaner production, and internal and external recycling of exceeding materials.

  6. Lung function and functional capacity among foundry workers using effective risk control measures.

    Science.gov (United States)

    Bernardes, Rosane Andrea Bretas; Chiavegato, Luciana Dias; de Moraes, Mônica Vasconcelos; Negreiros, Alexandher; Padula, Rosimeire Simprini

    2015-01-01

    Inhaled dust in the environment can trigger specific reactions in the airways and cause various respiratory diseases. Evaluate the lung function and functional capacity of foundry workers who are exposed to metals and use effective control measures. A cross-sectional study was realized with 108 workers at a bronze foundry and machining plant and in maintenance at a private university, both in Brazil. The workers were divided into two groups: the study group exposed to metals but using risk control measues and a control group not exposed to metal work. The Medical Research Council Questionnaire on Respiratory Symptoms and the International Physical Activity Questionnaire were administered, and lung function and functional capacity were evaluated. Comparative statistics were used to identify differences in the outcome measures between the two groups. The groups had similar personal and anthropometric characteristics and time on the job. Spirometry and peak expiratory flow presented no significant differences between the groups. And there was also no statistically significant difference between groups in functional capacity as assessed by performance on the six-minute walk test. Foundry industry workers in Brazil who were exposed to metal but used risk control measures had similar lung function and functional capacity when compared to the control group who were not exposed to metal. This is a positive results and maybe related to age, time exposure and control of occupational hazards. However, these workers need to continue being monitored in longitudinal studies.

  7. Pressure-Velocity Correlations in the Cove of a Leading Edge Slat

    Science.gov (United States)

    Wilkins, Stephen; Richard, Patrick; Hall, Joseph

    2015-11-01

    One of the major sources of aircraft airframe noise is related to the deployment of high-lift devices, such as leading-edge slats, particularly when the aircraft is preparing to land. As the engines are throttled back, the noise produced by the airframe itself is of great concern, as the aircraft is low enough for the noise to impact civilian populations. In order to reduce the aeroacoustic noise sources associated with these high lift devices for the next generation of aircraft an experimental investigation of the correlation between multi-point surface-mounted fluctuating pressures measured via flush-mounted microphones and the simultaneously measured two-component velocity field measured via Particle Image Velocimetry (PIV) is studied. The development of the resulting shear-layer within the slat cove is studied for Re =80,000, based on the wing chord. For low Mach number flows in air, the major acoustic source is a dipole acoustic source tied to fluctuating surface pressures on solid boundaries, such as the underside of the slat itself. Regions of high correlations between the pressure and velocity field near the surface will likely indicate a strong acoustic dipole source. In order to study the underlying physical mechanisms and understand their role in the development of aeroacoustic noise, Proper Orthogonal Decomposition (POD) by the method of snapshots is employed on the velocity field. The correlation between low-order reconstructions and the surface-pressure measurements are also studied.

  8. Linking energy efficiency and innovation practices: Empirical evidence from the foundry sector

    International Nuclear Information System (INIS)

    Cagno, Enrico; Ramirez-Portilla, Andres; Trianni, Andrea

    2015-01-01

    The Europe 2020 strategy currently promotes energy efficiency and innovation through disconnected targets focusing on either energy or R&D. Similar policies indicate that in practice, these two concepts are usually perceived as mutually exclusive. Furthermore, evidence in the literature regarding the relationship between R&D and energy efficiency is still highly limited. This exploratory study aims to address this gap by investigating the link between innovation practices and energy efficiency through a multiple case study of 30 foundries in Northern Italy. We analysed the firms' innovativeness, measured by internal R&D and Open Innovation practices (inbound and outbound), and energy efficiency, measured by specific energy consumption, level of adoption of energy-efficient technologies and barriers to energy efficiency. The results seem to show that those foundries complementing internal R&D with inbound practices have a higher level of energy efficiency, a higher level of adoption of available technologies, and a lower perception of barriers to efficiency improvements. This finding suggests that diversifying innovation practices could lead to better performance with respect to all three indicators of energy efficiency analysed. This study contributes to understanding how more innovative firms can be more energy efficient, providing interesting highlights for managers and policymakers. -- Highlights: •The relation between innovation practices and energy efficiency is articulated. •The link between innovation practices and energy efficiency is tested for foundries. •Energy efficiency is measured with three different indicators. •Analyses of the relations between these indicators support the link with innovation. •Concurrent adoption of internal R&D and inbound practices leads to higher efficiency

  9. The Analysis of Foundry Engineering of Copper Alloys Based on the Research of a Metallurgist Settlement in Szczepidło

    Directory of Open Access Journals (Sweden)

    Garbacz-Klempka A.

    2017-03-01

    Full Text Available The article presents chosen aspects of foundry engineering of the settlement dwellers, including the archaeometric characteristics and metal science analysis of the artefacts, as well as an attempted reconstruction of the production organization. Discovered in Szczepidło (Greater Poland, the foundry workshop is unique in Central European Bronze Age.

  10. Interaction of smoking, uptake of polycyclic aromatic hydrocarbons, and cytochrome P450IA2 activity among foundry workers

    DEFF Research Database (Denmark)

    Sherson, D; Sigsgaard, T; Overgaard, E

    1992-01-01

    .56-5.24). The same was true for smoking controls and foundry workers (9.10, 95% CI 8.00-10.20 and 8.69, 95% CI 7.37-10.01). Both smoking groups had raised IA2 ratios compared with non-smokers (p less than 0.01). Non-smoking controls and foundry workers had similar hpU concentrations (0.16, 95% CI 0.10-0.22 and 0...... hygienic samples (respirable dust 1.2 to 3.52 mg/m3 (93 samples)) and as total PAH (0.46 micrograms/m3) and pyrene concentrations (0.28 micrograms/m3) (six samples). Non-smoking controls and foundry workers had similar IA2 ratios (5.63, 95% confidence interval (95% CI) 4.56-6.70 and 4.40, 95% CI 3...

  11. Foundry industries: environmental aspects and environmental condition indicators; Industrias de fundicion: aspectos ambientales e indicadores de condicion ambiental

    Energy Technology Data Exchange (ETDEWEB)

    Sosa, B. s.; Banda-Noriega, R. B.; Guerrero, E. M.

    2013-03-01

    Nowadays, environmental indicators are widely used as effective tools to assist decision-making in both public and private sectors. The lack of literature and research about local and regional Environmental Condition Indicators (ECI), the poor knowledge regarding solid waste generation, effluents and gas emissions from foundry industries, and their particular location in the urban area of Tandil, Argentina are the main reasons for this investigation, aiming to develop a set a of ECI to provide information about the environment in relation to the foundry industry. The study involves all the foundries located in the city between March and April 2010. The set of ECI developed includes 9 indicators for air, 5 for soil and 1 for water. Specific methodology was used for each indicator. (Author) 31 refs.

  12. Use of wasted foundry sand (WFS) as a partial substitute for silica in a soda lime glass

    International Nuclear Information System (INIS)

    Martin, A.C.; Ueno, O.K.; Folgueras, M.V.

    2016-01-01

    The waste foundry sand (WFS) is the main waste generates in foundry industries. Studies in the literature suggest the use of WFS in different materials, such as concrete, brick or asphalt. This work aims to partially replace the silica of a soda-lime glass by the WFS. The waste foundry sand has in its composition elements such as iron and aluminum that can affect the glass quality, which justifies the residue processing to reduce the impurity content. The treatments, that included mechanical agitation and thermal treatment, resulted in a slight decrease in the percent of iron with consequent increase of the silica content. After treatment, some sands were incorporated into the glass, that showed green color but with lower absorption intensity for the sand with less iron content. It was observed that it's possible to obtain glasses using WFS, however, there is difficulty in color controlling. (author

  13. New sol–gel refractory coatings on chemically-bonded sand cores for foundry applications to improve casting surface quality

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Poulsen, T.; Stage, R.K.

    2011-01-01

    Foundry refractory coatings protect bonded sand cores and moulds from producing defective castings during the casting process by providing a barrier between the core and the liquid metal. In this study, new sol–gel refractory coating on phenolic urethane cold box (PUCB) core was examined. The coa......Foundry refractory coatings protect bonded sand cores and moulds from producing defective castings during the casting process by providing a barrier between the core and the liquid metal. In this study, new sol–gel refractory coating on phenolic urethane cold box (PUCB) core was examined......–gel coated cores have better surface quality than those from uncoated cores and comparable surface quality with the commercial coatings. Therefore, the new sol–gel coating has a potential application in the foundry industry for improving the surface finish of castings thereby reducing the cost of fettling...

  14. Energy conservation in flame-heated hearth furnaces in aluminium foundries. Pt. 1

    Energy Technology Data Exchange (ETDEWEB)

    Moser, R

    1981-01-01

    There are two fields for energy saving: The aluminium foundries obtain the electrolytic metal in liquid form and therefore also excessive heat. This must be used. The furnaces must be designed and operated so that they use as little energy as possible. Both subjects are investigated by considering 59 existing plants in Europe. They are compared regarding energy consumption and heat balance. A series of possibilities for improved use of fuel, such as improvement of the burner setting, automatic regulation of excess air and use of combustion with enriched oxygen supply are given.

  15. Free radicals of an aromatic nature in air samples from iron foundries

    Energy Technology Data Exchange (ETDEWEB)

    Westerberg, L M

    1982-01-01

    Free radicals of relatively long life were identified as spin adducts of phenyl-N-tert-butylnitrone. Pyrolysis studies showed the radicals were oxy-radicals. The hyperfine splitting constants of spin adducts of radicals from the pyrolysis in air of benzo(a)pyrene, coal tar pitch, and moulding sand containing hard coal dust were the same as those of the radicals found in foundry air. Since these radicals can bind to DNA, they must be considered when estimating the hazardous effects of polluted air.

  16. Determination of pollutants in foundry during the manufacture of metal constructions for high buildings

    Science.gov (United States)

    Ivanova, Irina; Sushko, Elena; Lyshnikova, Anna; Prykina, Larisa

    2018-03-01

    Current developments are devoted to the environmental safety of the foundry. There is a significant amount of pollutants, according to dust, which is released in the working area, during the manufacture of metal structures for high buildings. From the point of dust extraction, the most unfavorable areas are shot blasting, sand-blasting chambers and knockout grills. The weight fraction of dust composition with diameters up to 20 μm reaches 43,8% by mass, according to experimental analysis. This kind of dust is the most dangerous to employees and also it creates problems for dust-cleaning in the air.

  17. Replies to Challenges in the Field of Air Pollution Control in Foundry Plants

    Directory of Open Access Journals (Sweden)

    Margraf R.

    2012-09-01

    Full Text Available The solution of applications for air pollution control in foundries for iron and non-ferrous metals may not only be understood as the observance of requested emission limit values at the stack outlet. An effective environmental protection already starts with the greatest possible capture of pollutants at the source with at the same time minimisation of the volume flow necessary for this. Independent of this, the downstream installed filtration system has to realise a degree of separation of definitely above 99%.

  18. Comparative Analysis of the Thermal Insulation of Traditional and Newly Designed Protective Clothing for Foundry Workers

    Directory of Open Access Journals (Sweden)

    Iwona Frydrych

    2016-09-01

    Full Text Available An objective of the undertaken research was checking the applicability of aluminized basalt fabrics for the production of clothing for foundry workers. The results of flammability, the resistance to contact, convective and radiation heat, as well as the resistance to big molten metal splashes confirmed the thesis of applicability of the packages with the use of aluminized basalt fabric content for the assumed purpose; therefore, such protective clothing was produced. Thermal comfort of foundry workers is very important and related to many factors, i.e., the structure of the protective clothing package, the number of layers, their thickness, the distance between the body and appropriate underwear. In the paper, a comparison of the results of thermal insulation measurement of two kinds of protective clothing is presented: the traditional one made of aluminized glass fabrics and the new one made of aluminized basalt fabrics. Measurements of clothing thermal insulation were conducted using a thermal manikin dressed in the protective clothing and three kinds of underwear products covering the upper and lower part of the manikin.

  19. Replies to Challenges in the Field of Air Pollution Control in Foundry Plants

    Directory of Open Access Journals (Sweden)

    R. Margraf

    2012-09-01

    Full Text Available The solution of applications for air pollution control in foundries for iron and non-ferrous metals may not only be understood as theobservance of requested emission limit values at the stack outlet. An effective environmental protection already starts with the greatest possible capture of pollutants at the source with at the same time minimisation of the volume flow necessary for this. Independent of this, the downstream installed filtration system has to realise a degree of separation of definitely above 99%.Furthermore, when selecting the filter construction, attention has to be paid to a high availability. An even temporarily productionwithout filter will more and more no longer be accepted by residents and authorities. Incidents at the filter lead to a shutdown of the whole production.Additional measures for heat recovery while preparing concepts for filtration plants help to reduce the energy consumption and servefor a sustained conservation of environment.A consequent consideration of the items above is also condition for the fact that environmental protection in foundries remainsaffordable. The lecture deals with the subjects above from the point of view of a plant constructor.

  20. Risk assessment in a foundry unit by energy trace and barrier analysis method (ETBA

    Directory of Open Access Journals (Sweden)

    S.A. Ayati

    2010-01-01

    Full Text Available Background and aimsAs a Development of Industrial process, human, environment,equipment, material and validity of system has been exposed to hazardous conditions. Regards of32.3 percent of occupations in industries, this study focused on risk assessment of foundry unit byenergy trace and barrier analysis (ETBA method and presented approaches to control of accident.Methodsthe recent study is as a case study one to risk assessment in a foundry unit in Qazvinindustrial city in1387. In this study risks were founded by ETBA method and evaluated by MILSTD-882B. Data were collected by direct observations, interview with workers and supervisorand engineers, walking-talking through method, documents investigation of operationalprocessors, preventive maintenances, equipment technical properties, accidental and medicaldocuments. Finally ETBA worksheets completed.Findingstotally 154 risks has been found. 40 from total are been unacceptable risk, 68unfavorable and also 46 acceptable but with remediation action. Casting workshop had risks morethan other workshops (with 74 identified risks.Potential and heat energies were founded as mosthazardous energies, with respectively 51 and 38 risk cases.ConclusionThis study recommended to be done actions for identification and control risk,such as: safety training, occupation training, preventive maintenance, contract safety, safetycommunication and safety audit group.

  1. Tools and Strategies for Product Life Cycle Management ñ A Case Study in Foundry

    Science.gov (United States)

    Patil, Rajashekar; Kumar, S. Mohan; Abhilash, E.

    2012-08-01

    Advances in information and communication technology (ICT) have opened new possibilities of collaborations among the customers, suppliers, manufactures and partners to effectively tackle various business challenges. Product Life Cycle Management(PLM) has been a proven approach for Original Equipment Manufacturers (OEMs) to increase their productivity, improve their product quality, speed up delivery, and increase their profit and to become more efficient. However, their Tier 2 and Tier 3 suppliers like foundry industries are still in their infancy without adopting PLM. Hence to enhance their understanding, the basic concepts, the tools and strategies for PLM are presented is this paper. By selecting and implementing appropriate PLM strategies in a small foundry, an attempt was also made to understand the immediate benefits of using PLM tools (commercial PLM software and digital manufacturing tools). This study indicated a reduction in lead time and improved utilization of organizational resources in the production of automobile impeller. These observations may be further extrapolated to other multiproduct, multi-discipline and multi-customer companies to realize the advantages of using PLM technology

  2. Waste Foundry Sand Usage for Building Material Production: A First Geopolymer Record in Material Reuse

    Directory of Open Access Journals (Sweden)

    Neslihan Doğan-Sağlamtimur

    2018-01-01

    Full Text Available In order to bring a solution to the problem of waste foundry sand (WFS in the foundry sector and achieve its reuse, geopolymer building material (as a cementless technology was produced from the WFS for the first time in the literature in this study. The physical and mechanical characteristics of this material were determined. In the first part of the experimental step, the sieve analysis, loose/tight unit weight, and loss of ignition of the WFS were obtained as well as the ultimate analysis. In the second step, the water absorption percentage, porosity, unit weight, and compressive strength tests were conducted on the WFS-based geopolymer specimens activated by chemical binders (sodium hydroxide: NaOH and sodium silicate: Na2SiO3. As the unit weights of all the produced samples were lower than 1.6 g/cm3, they may be considered as lightweight building materials. The minimum compressive strength value for building wall materials was accepted as 2.5 MPa by national standards. In this study, the maximum compressive strength value was measured as 12.3 MPa for the mixture incorporation of 30% Na2SiO3 at the curing temperature of 200°C in 28 days. It was concluded that this geopolymer material is suitable for using as a building wall material.

  3. A Production Planning Model for Make-to-Order Foundry Flow Shop with Capacity Constraint

    Directory of Open Access Journals (Sweden)

    Xixing Li

    2017-01-01

    Full Text Available The mode of production in the modern manufacturing enterprise mainly prefers to MTO (Make-to-Order; how to reasonably arrange the production plan has become a very common and urgent problem for enterprises’ managers to improve inner production reformation in the competitive market environment. In this paper, a mathematical model of production planning is proposed to maximize the profit with capacity constraint. Four kinds of cost factors (material cost, process cost, delay cost, and facility occupy cost are considered in the proposed model. Different factors not only result in different profit but also result in different satisfaction degrees of customers. Particularly, the delay cost and facility occupy cost cannot reach the minimum at the same time; the two objectives are interactional. This paper presents a mathematical model based on the actual production process of a foundry flow shop. An improved genetic algorithm (IGA is proposed to solve the biobjective problem of the model. Also, the gene encoding and decoding, the definition of fitness function, and genetic operators have been illustrated. In addition, the proposed algorithm is used to solve the production planning problem of a foundry flow shop in a casting enterprise. And comparisons with other recently published algorithms show the efficiency and effectiveness of the proposed algorithm.

  4. Value-Chain Dynamics of the West Point Foundry, 1817-1911: A Historical Case Analysis in Marketing

    Science.gov (United States)

    Petkus, Ed, Jr.

    2013-01-01

    This case provides the opportunity for students to explore marketing and value/supply-chain dynamics in a unique historical context. The West Point Foundry (WPF), located in Cold Spring, New York, was one of the most important manufacturing ventures in the United States from 1817 to 1911. The case outlines the supply-chain details of the WPF as…

  5. Determining the optimal index of heat stress in foundry, die casting and road construction industries using FAHP_Topsis

    Directory of Open Access Journals (Sweden)

    Maryam Dehghanipoor

    2016-12-01

    Full Text Available Introduction: Heat stress is one of the harmful risks in casting and die casting industries, which can not only cause work-related diseases but also can impair the performance and safety of workers. Since the indicators that are used to evaluate heat stress are very different, it is very difficult to choose a suitable index. The aim of this study was to determine the optimum heat stress index in foundry, die-cast, and road construction industries using FAHP and Topsis methods. Material and Method: In order to determine optimum heat stress index in foundry, die-cast, and road construction industries, first, the prioritization criteria were defined by experts (including ease of measurement, measurement accuracy, comprehensiveness, time, cost, and correlation. Then, considering these criteria, the best heat stress index was determined based on experts’ opinions and using FAHP and Topsis methods. Result: The results of this study suggest that given the current conditions and criteria, WBGT and P4SR is the best indices for foundry, die casting and construction. Conclusion: The results showed that according to comprehensiveness, accuracy and correlation criteria, the WBGT index is considered as the best indicator of heat stress assessment in foundry, die-cast and road construction industries. Moreover, the HSI ranked in the last place due to the complexity and cost of its calculation.

  6. Respirable silica dust exposure amongst foundry workers in Gauteng, South Africa: A task-based risk assessment

    CSIR Research Space (South Africa)

    Khoza, NN

    2012-09-01

    Full Text Available /m³ respectively in foundry two. The maximum exposure concentration was 0.835 mg/m³ and minimum exposure was 0.010 mg/m³. Data were analysed by using SPSS version 18. The highest exposed occupations were moulders, sand mixers, furnace operators, shake...

  7. The Synthetic Aperture Radar Science Data Processing Foundry Concept for Earth Science

    Science.gov (United States)

    Rosen, P. A.; Hua, H.; Norton, C. D.; Little, M. M.

    2015-12-01

    Since 2008, NASA's Earth Science Technology Office and the Advanced Information Systems Technology Program have invested in two technology evolutions to meet the needs of the community of scientists exploiting the rapidly growing database of international synthetic aperture radar (SAR) data. JPL, working with the science community, has developed the InSAR Scientific Computing Environment (ISCE), a next-generation interferometric SAR processing system that is designed to be flexible and extensible. ISCE currently supports many international space borne data sets but has been primarily focused on geodetic science and applications. A second evolutionary path, the Advanced Rapid Imaging and Analysis (ARIA) science data system, uses ISCE as its core science data processing engine and produces automated science and response products, quality assessments and metadata. The success of this two-front effort has been demonstrated in NASA's ability to respond to recent events with useful disaster support. JPL has enabled high-volume and low latency data production by the re-use of the hybrid cloud computing science data system (HySDS) that runs ARIA, leveraging on-premise cloud computing assets that are able to burst onto the Amazon Web Services (AWS) services as needed. Beyond geodetic applications, needs have emerged to process large volumes of time-series SAR data collected for estimation of biomass and its change, in such campaigns as the upcoming AfriSAR field campaign. ESTO is funding JPL to extend the ISCE-ARIA model to a "SAR Science Data Processing Foundry" to on-ramp new data sources and to produce new science data products to meet the needs of science teams and, in general, science community members. An extension of the ISCE-ARIA model to support on-demand processing will permit PIs to leverage this Foundry to produce data products from accepted data sources when they need them. This paper will describe each of the elements of the SAR SDP Foundry and describe their

  8. Design and production of a novel sand materials strength testing machine for foundry applications

    DEFF Research Database (Denmark)

    Nwaogu, Ugochukwu Chibuzoh; Hansen, K. S.; Tiedje, Niels Skat

    2012-01-01

    testing machine was designed and built for both green sand and chemically-bonded sand materials. This machine measures and presents the loading response as a force-displacement profile from which the mechanical properties of the moulding materials can be deduced. The system was interfaced to a computer......In the foundry, existing strength testing machines are used to measure only the maximum fracture strength of mould and core materials. With traditionally used methods, the loading history to ascertain deformation of the material is not available. In this paper, a novel moulding material strength...... with a commercial PC based-control and data acquisition software. The testing conditions and operations are specified in the user interface and the data acquisition is made according to specifications. The force and displacements were calibrated to ensure consistency and reliability of the measurement data...

  9. Exploitation of the residue of foundry exhauster powder in ceramics for covering

    International Nuclear Information System (INIS)

    Valentina, Luiz Veriano Oliveira Dalla; Folgueras, Marilena Valadares; Knop, Wanessa Rejane; Semptikovski, Simone Claudiano

    2010-01-01

    The work evaluates the possibility of the use the exhauster powder generated in the foundry process in ceramic mass atomized semigre type. This residue was characterized by scanning electron microscopy, x-ray diffractometry and thermal analysis (DSC, TG). Formulations were prepared with different exhauster powder content. The sintered materials between 1000°C at 1 200 deg C. The results showed of the scanning electron microscopy and the characterization of the technological properties (water absorption, linear shrinkage and apparent density) had demonstrated the viability of the use of this residue. Through experiments it was observed that the exhauster powder promoted an increment in the sintering degree, and raised texts of this they increase of the porosity and intensification in the color of the new material. That is, it is possible to incorporate small amounts of the exhauster powder in substitution the substances cousins of natural origin. (author)

  10. [The genetic component of chronic respiratory diseases in workers of foundry productions].

    Science.gov (United States)

    Loskutov, D V; Khamitova, R Ya

    Review of the literature shows that currently there is an accumulation of data on the genetic determination of individual susceptibility to adverse industrial factors. Material of the research were high molecular DNA samples isolated from epithelial mouth scrapings in 99 foundry workers. Study of polymorphic variants of interleukin genes was performed by means of the analysis ofproducts of amplification of specific regions of the genome. Homozygous genotype TNF-a (-308A/G) was established to increase the relative risk of shaping of chronic respiratory diseases: with AA alleles - by 6.4 times and GG alleles - by 2.4 times, while the heterozygous genotype (AG) decreases - by 1. 9 times. Polymorphism of gene IL-1β (+3953 T / C) had no significance for the development of respiratory disease. Genotyping interleukins, involved in the inflammatory responses of the bronchopulmonary tract, can be considered as an element ofprimary prevention in industries with a high risk for shaping of respiratory diseases.

  11. The effect of main alloying elements on the physical properties of Al–Si foundry alloys

    International Nuclear Information System (INIS)

    Stadler, F.; Antrekowitsch, H.; Fragner, W.; Kaufmann, H.; Pinatel, E.R.; Uggowitzer, P.J.

    2013-01-01

    In this study we describe the effect of the main alloying elements Si, Cu and Ni on the thermal properties of hypoeutectic and near-eutectic Al–Si foundry alloys. By means of systematic variations of the chemical composition, the influence of the amount of ‘second phases’ on the thermal conductivity, thermal expansion coefficient, and thermal shock resistance is evaluated. Thermodynamic calculations predicting the phase formation in multi-component Al–Si cast alloys were carried out and verified using SEM, EDX and XRD analysis. The experimentally obtained data are discussed on a systematic basis of thermodynamic calculations and compared to theoretical models for the thermal conductivity and thermal expansion of heterogeneous solids.

  12. MODERN RESOURCE-SAVING TECHNOLOGIES IN FOUNDRY PRODUCTION OF JSC «MINSK TRAKTOR PLANT»

    Directory of Open Access Journals (Sweden)

    F. A. Domotenko

    2016-01-01

    Full Text Available In article the main world tendencies of development of the production technology of sandy cores and value of this production in complex technology of manufacture of castings are considered. It is established that the most rational way of production technically and economically is manufacture of wafer sandy cores using the Cold-box-amin technology. Scientific, technical, technological and economic aspects of modernization of foundry production of JSC MTZ with complete transition to production of sandy cores on the resource-saving Cold-box-amin technology are provided. The main distinctive feature of this reequipment – all planned works are based on the domestic technological developments and the equipment created in the cooperation by specialists of JSC BELNIILIT and JSC MTZ. Within GNTP essential support to the provided works was given by the state.

  13. The analysis of the wax foundry models fabrication process for the CPX3000 device

    Directory of Open Access Journals (Sweden)

    G. Budzik

    2011-04-01

    Full Text Available The paper presents possibilities of creating wax founding models by means of CPX3000 device. The device is used for Rapid Prototypingof models made of foundry wax in an incremental process. The paper also presents problems connected with choosing technologicalparameters for incremental shaping which influence the accuracy of created models. Issues connected with post-processing are alsodescribed. This process is of great importance for obtaining geometrically correct models. The analysis of parameters of cleaning models from supporting material is also presented. At present CPX3000 printer is the first used in Poland device by 3D Systems firm for creating wax models. The printer is at The Faculty of Mechanical Engineering at Rzeszów University of Technology.

  14. Strobloy — The New Combined Grain Refiner and Modifier for Hypoeutectic AlSi Foundry Alloys

    Science.gov (United States)

    Bondhus, Eivind; Sagstad, Trond

    Hydelko presents a new combination alloy for use in hypoeuctectic aluminium silicon foundry alloys. Strobloy simplifies today's addition practice of grain refiner and modifier by reducing the number of additions from two to one. Strobloy is a combination product between the well-established TiBloy, and strontium. The alloy contains nucleating particles in the form of the mixed boride (Al, Ti)B2, which is beneficial regarding settling and grain refining efficiency. Strontium is present as fast-dissolving AL4Sr particles. Trials carried out indicate that Strobloy shows very good performance compared to separate additions of TiBloy/AlTi5B1 and AlSr master alloy. The grain refining efficiency and modification level is the same or better. This paper displays results collected from tests done with different strontium levels in an A356 alloy. Comparisons to separate additions of TiBloy and AlSr are presented.

  15. Evaluation of microplastics in Jurujuba Cove, Niterói, RJ, Brazil, an area of mussels farming.

    Science.gov (United States)

    Castro, Rebeca Oliveira; Silva, Melanie L; Marques, Mônica Regina C; de Araújo, Fábio V

    2016-09-15

    Once non-biodegradable, microplastics remain on the environment absorbing toxic hydrophobic compounds making them a risk to biodiversity when ingested or filtered by organisms and entering in the food chain. To evaluate the potential of the contamination by microplastics in mussels cultivated in Jurujuba Cove, Niterói, RJ, waters of three stations were collected during a rain and dry seasons using a plankton net and later filtered. Microplastics were quantified and characterized morphologically and chemically. The results showed a high concentration of microplastics in both seasons with diversity of colors, types and sizes. Synthetic polymers were present in all samples. The presence of microplastics was probably due to a high and constant load of effluent that this area receives and to the mussel farming activity that use many plastic materials. Areas with high concentrations of microplastics could not be used for mussel cultivation due to the risk of contamination to consumers. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Beyond barriers – A case study on driving forces for improved energy efficiency in the foundry industries in Finland, France, Germany, Italy, Poland, Spain, and Sweden

    International Nuclear Information System (INIS)

    Thollander, Patrik; Backlund, Sandra; Trianni, Andrea; Cagno, Enrico

    2013-01-01

    Highlights: • Results are based on a questionnaire in the European foundry industry. • The energy efficiency potential is assed to be 7.5% of the total energy use. • Most important drivers to and barriers for energy efficiency are financial followed by organizational. • EPC is used among 23% of the foundries, third party financing among 12%. • Large energy management improvement potentials are uncovered. - Abstract: Energy management plays an important role in the transformation of industrial energy systems towards improved energy efficiency and increased sustainability. This paper aims to study driving forces for improved energy efficiency in some European energy-intensive foundry industries. The investigation has been conducted as a multiple case study involving 65 foundries located in Finland, France, Germany, Italy, Poland, Spain, and Sweden. The most relevant perceived driving forces were found to be financially related, followed by organizational driving forces. Nevertheless, some differences can be appreciated according to the firm’s size and country. Almost half of the studied foundries lack a long-term energy strategy, about one-fourth stated that they have used Energy Performance Contracting (EPC), and only approximately one in ten foundries have used Third Party Financing (TPF). Among the studied foundries, three out of five have conducted an energy audit. On average, the energy saving potential according to the respondents is stated to be 7.5%. In conclusion, energy management in the European foundry industry, despite increasing energy prices and extensive energy policy actions taken by the EU, still seems to have great improvement potential, calling for future research and policy actions in the field

  17. A Study of the Cold Resistance of Pipe Coiled Stock Produced at Foundry-Rolling Works. Part 2

    Science.gov (United States)

    Bagmet, O. A.; Naumenko, V. V.; Smetanin, K. S.

    2018-03-01

    Results of a study of coiled stock from low-carbon steels alloyed with manganese and silicon and different additives of niobium and titanium are presented. The coiled stock is produced at foundry-rolling works by the method of direct rolling of thin slabs right after their continuous casting. The microdeformation of the crystal lattice and the crystallographic texture are determined. The conditions of formation of the most favorable structure and texture in the steels are specified.

  18. Suitability of a South African silica sand for three-dimensional printing of foundry moulds and cores

    Directory of Open Access Journals (Sweden)

    Nyembwe, Kasongo

    2016-11-01

    Full Text Available Applications of three-dimensional printing (3DP to metal casting include, among other things, the direct manufacturing of foundry moulds and cores in refractory materials such as silica sand. The main properties of silica sand that are essentially related to the traditional moulding and core-making processes are: size distribution, clay content, pH, acid demand, and refractoriness. The silica sand used for 3DP must also be appropriately selected for the layer-based manufacturing process involved in 3DP. Properties such as grain size distribution, grain surface morphology, angularity, flowability, and recoating abilities have a particular importance when determining sand suitability. Because of these extra requirements, only a limited range of available foundry silica sands can be used for 3DP processes. The latter situation explains the scarcity and high cost of suitable silica sands, thus contributing to the relatively high operational costs of the 3DP processes for the production of sand moulds and cores. This research paper investigates the suitability of a locally-available silica sand for use in a Voxeljet VX1000 3DP machine. The local silica sand was assessed and compared with an imported silica sand recommended by the manufacturer of 3DP equipment in terms of foundry characteristics and recoating behaviour. The study shows that, despite the differences between the characteristics of the two silica sands, the local sand could be considered a suitable alternative to imported sand for rapid sand casting applications.

  19. Risk assessment related to manual handling on choosen work possition in foundry Alstom Power Sp. z o. o.

    Directory of Open Access Journals (Sweden)

    G. Kowal

    2010-04-01

    Full Text Available Manual handling remains one of the different types of transport inside working place, although technological progress and modernorganization of work. Manual transport as a transport inside working place is related to foundry industry. According to polish lawregulations employer has to give consideration to manual handling in professional risk assessment and introduce actions for manualhandling reduction. In Foundry Elblag case there is found that in many processes manual handling are made by workers. For example wecan choose melting processes (additives manual feeding, mixing and pulling metallurgical slag, etc. or fettling processes like grinding.Objective of that analysis was to define level of risk related to manual handling in work stand chosen and define activities impacted onrisk assessment result with biggest range. For risk reduction, technical and organizational solutions were shown (better ergonomically work stand, method of work and worker’s awareness about good practices. In this study methods related to manual handling risk assessment were described, focus on KIM method used in Foundry Elblag. Key Item Method allow to estimate the risk by simple calculation based on key indicators (time rating points, rating points of mass, posture or work condition. Points were chosen based on timekeeping, information from workers and foreman.

  20. Combining optimisation and simulation in an energy systems analysis of a Swedish iron foundry

    International Nuclear Information System (INIS)

    Mardan, Nawzad; Klahr, Roger

    2012-01-01

    To face global competition, and also reduce environmental and climate impact, industry-wide changes are needed, especially regarding energy use, which is closely related to global warming. Energy efficiency is therefore an essential task for the future as it has a significant impact on both business profits and the environment. For the analysis of possible changes in industrial production processes, and to choose what changes should be made, various modelling tools can be used as a decision support. This paper uses two types of energy analysis tool: Discrete Event Simulation (DES) and Energy Systems Optimisation (ESO). The aim of this study is to describe how a DES and an ESO tool can be combined. A comprehensive five-step approach is proposed for reducing system costs and making a more robust production system. A case study representing a new investment in part of a Swedish iron foundry is also included to illustrate the method's use. The method described in this paper is based on the use of the DES program QUEST and the ESO tool reMIND. The method combination itself is generic, i.e. other similar programs can be used as well with some adjustments and adaptations. The results from the case study show that when different boundary conditions are used the result obtained from the simulation tools is not optimum, in other words, the result shows only a feasible solution and not the best way to run the factory. It is therefore important to use the optimisation tool in such cases in order to obtain the optimum operating strategy. By using the optimisation tool a substantial amount of resources can be saved. The results also show that the combination of optimisation and simulation tools is useful to provide very detailed information about how the system works and to predict system behaviour as well as to minimise the system cost. -- Highlights: ► This study describes how a simulation and an optimisation tool can be combined. ► A case study representing a new

  1. Health-hazard evaluation report GHETA 83-309-1405, Chrysler Corporation Foundry, Indianapolis, Indiana

    International Nuclear Information System (INIS)

    Patil, A.

    1984-01-01

    In response to a request arising out of employee concerns over the medical surveillance program at the Chrysler Corporation Foundry located in Indianapolis, Indiana, an evaluation was made of chest radiographs evaluated by the program with specific concern directed to disagreement on the radiographic diagnosis of pneumoconiosis. The request was made by the Chrysler Corporation and the United Auto Workers National Joint Committee on Health and Safety. Three NIOSH certified B-readers independently interpreted a set of 78 systematically sampled posteroanterior (PA) chest radiographs from the system files. These interpretations were compared among themselves and with company interpretations. While none of the radiographs was deemed unreadable, 35% were classified as having poor technical quality. Only one film was found which had a profusion of small opacities, and the company had interpreted the film as positive. Overall, agreement on proportion of positive readings and agreement on individual films was as good between the company and B-readers as it was between any two of the individual B-readers. The author recommends, however, that in order to avoid future complaints of the nature, the company should use standard radiographic equipment and techniques, NIOSH certified B-readers, and current international classifications of radiographs for pneumoconioses in their medical surveillance program

  2. Mechanical and Durability Properties of Concrete Made with Used Foundry Sand as Fine Aggregate

    Directory of Open Access Journals (Sweden)

    G. Ganesh Prabhu

    2015-01-01

    Full Text Available In recent years, the construction industry has been faced with a decline in the availability of natural sand due to the growth of the industry. On the other hand, the metal casting industries are being forced to find ways to safely dispose of waste foundry sand (FS. With the aim of resolving both of these issues, an investigation was carried out on the reuse of waste FS as an alternative material to natural sand in concrete production, satisfied with relevant international standards. The physical and chemical properties of the FS were addressed. The influence of FS on the behaviour of concrete was evaluated through strength and durability properties. The test results revealed that compared to the concrete mixtures with a substitution rate of 30%, the control mixture had a strength value that was only 6.3% higher, and this enhancement is not particularly high. In a similar manner, the durability properties of the concrete mixtures containing FS up to 30% were relatively close to those of control mixture. From the test results, it is suggested that FS with a substitution rate of up to 30% can be effectively used in concrete production without affecting the strength and durability properties of the concrete.

  3. Properties of made by different methods of RP impeller foundry patterns

    Directory of Open Access Journals (Sweden)

    G. Budzik

    2007-04-01

    Full Text Available This article presents the tests of properties of foundry patterns of turbocharger turbine impeller. Impellers prototypes were predestinated for casting by method losing patterns. There were carried out tests of these prototypes made by different methods of Rapid Prototyping (RP. Two impeller were made by growth methods: stereolitography (SLA and three dimensional printing (3DP. One prototype was made by the method of Vacuum Casting as a wax casting. Tests were executed in the Department of Machine Design of Rzeszow University of Technology in cooperation with WSK PZL Rzeszow and Car Technology Krakow. First impeller was carried out by method of stereolitography on SLA 250 plant. That pattern was also used to carry out silicon matrix for casting of wax pattern. Next pattern was printed by three dimensional printer Z510 from the powder ZP14. Good removability of the pattern from the mould is particularly essential for impellers of small turbines with blades of small thickness of their section. All pattern were tested on their removability from the ceramic mould. The best melting properties had the wax pattern. Patterns made from resin SL5170 (SLA and powder ZP14 (3DP were removed in the process of burning but about 1% of soot was left in the mould.

  4. Corrosion of immersed ceramic heat exchanger tubes in aluminium foundry baths

    Energy Technology Data Exchange (ETDEWEB)

    Bracho-Troconis, C.B.; Frot, G.; Bienvenu, Y. [Ecole des Mines de Paris, Evry (France). Centre des Materiaux; Frety, N. [Ecole des Mines d`Albi-Carmaux (France); Alliat, I. [CERSTA-Gaz de France, Saint-Denis (France)

    1997-12-31

    The corrosion of three non-oxide ceramics by Al-9Si-3Cu baths and by fluxes (mixtures of chlorides and fluorides of sodium and potassium) at about 750 C was studied in a foundry environment. Comparison of results of the metallurgical examination of A, a silicon-nitride-bonded silicon carbide and of B, a reaction-bonded silicon nitride, surface treated to fill all the external porosity provides some insight into the role of the bonding phase and the porosity. Grade C is a graphite bonded silicon carbide with an external protection by a ceramic glazing. The SiC phase in the tubes is inert to the corrosive liquids (attributed to the silicon content in the metal). A and C ceramics react only in the presence of a flux. Sodium and chlorine were identified in the corrosion products as well as AlN (A) and Al{sub 4}C{sub 3} (C), resulting from reaction of the silicon nitride or of the graphite bonding phase with aluminium. This suggests that the fluxes are responsible for the corrosive process, by causing the formation of gaseous aluminium halides which penetrate the porous bonding phase and react with it to form AlN or Al{sub 4}C{sub 3}. (orig.) 13 refs.

  5. Methods of Computational Intelligence in the Context of Quality Assurance in Foundry Products

    Directory of Open Access Journals (Sweden)

    Rojek G.

    2016-06-01

    Full Text Available One way to ensure the required technical characteristics of castings is the strict control of production parameters affecting the quality of the finished products. If the production process is improperly configured, the resulting defects in castings lead to huge losses. Therefore, from the point of view of economics, it is advisable to use the methods of computational intelligence in the field of quality assurance and adjustment of parameters of future production. At the same time, the development of knowledge in the field of metallurgy, aimed to raise the technical level and efficiency of the manufacture of foundry products, should be followed by the development of information systems to support production processes in order to improve their effectiveness and compliance with the increasingly more stringent requirements of ergonomics, occupational safety, environmental protection and quality. This article is a presentation of artificial intelligence methods used in practical applications related to quality assurance. The problem of control of the production process involves the use of tools such as the induction of decision trees, fuzzy logic, rough set theory, artificial neural networks or case-based reasoning.

  6. Workload assessment on foundry SME to enhance productivity using full time equivalent

    Directory of Open Access Journals (Sweden)

    Sari Amarria Dila

    2018-01-01

    Full Text Available Aluminium SME aims to increase the production amount by producing wok as much as 300 Units. The problem is workload analysis of operator on the wok production line in the wok foundry SME as well as the production cycle-making cycle time and analyze the workload received by the operator when producing 300 woks using the full time equivalent (FTE method. This study aims to measure the workload of each division worker in the production process with a total of 13 workers observed. This study provides a work division recommendation based on the workload that has been carefully examined. This research involves percentage of workload effectiveness and the wages of workers. In lathe division have overload workload. While the printing division, melting inspection division, packaging and transportation division including normal workload category and the percentage of good work effectiveness. The result provides recommendations for the addition of 2 workers in each division that includes the category of overload of the lathe division with the number of initial workers as many as 13 workers to 15 workers. In the last stage perform a simulation by comparing the system of prefix work and proposal. The simulation results obtained with the initial work system to get an average of 223 woks / day. Meanwhile, for the proposed work system to get an average output of 291 woks.

  7. Modeling of the influence of coarsening on viscoplastic behavior of a 319 foundry aluminum alloy

    International Nuclear Information System (INIS)

    Martinez, R.; Russier, V.; Couzinié, J.P.; Guillot, I.; Cailletaud, G.

    2013-01-01

    Both metallurgical and mechanical behaviors of a 319 foundry aluminum alloy have been modeled by means of a multiscale approach. The nano-scale, represented by the coarsening of Al 2 Cu precipitates, has been modeled according to the Lifshitz–Slyozov–Wagner (LSW) law in a range of temperature going from 23 °C to 300 °C up to 1000 h aging time. Results were then compared to transmission electron microscope (TEM) observations and are in good agreement with the experimental measurements. The model allows us to know the critical radius, the volume fraction and the number of particles per μm 3 in a α-phase representative volume element (RVE). The increase in yield stress generated by the interaction of dislocations with precipitates, lattice and solid solution, is modeled on the microscale. The yield stress becomes thus a function of the precipitation state, and is time/temperature dependent. These two models were then combined into a mechanical macroscale model in order to represent the Low Cycle Fatigue (LCF) behavior of the material. An elasto-viscoplastic law has been used and all the material parameters were experimentally determined with LCF stress/strain loops for the first cycle and for the mechanical steady state. The simulation results are in good agreement with the experiments.

  8. Effects of waste glass and waste foundry sand additions on reclaimed tiles containing sewage sludge ash.

    Science.gov (United States)

    Lin, Deng-Fong; Luo, Huan-Lin; Lin, Kuo-Liang; Liu, Zhe-Kun

    2017-07-01

    Applying sewage sludge ash (SSA) to produce reclaimed tiles is a promising recycling technology in resolving the increasing sludge wastes from wastewater treatment. However, performance of such reclaimed tiles is inferior to that of original ceramic tiles. Many researchers have therefore tried adding various industrial by-products to improve reclaimed tile properties. In this study, multiple materials including waste glass and waste foundry sand (WFS) were added in an attempt to improve physical and mechanical properties of reclaimed tiles with SSA. Samples with various combinations of clay, WFS, waste glass and SSA were made with three kiln temperatures of 1000°C, 1050°C, and 1100°C. A series of tests on the samples were next conducted. Test results showed that waste glass had positive effects on bending strength, water absorption and weight loss on ignition, while WFS contributed the most in reducing shrinkage, but could decrease the tile bending strength when large amount was added at a high kiln temperature. This study suggested that a combination of WFS from 10% to 15%, waste glass from 15% to 20%, SSA at 10% at a kiln temperature between 1000°C and 1050°C could result in quality reclaimed tiles with a balanced performance.

  9. The Implementation of Computer Platform for Foundries Cooperating in a Supply Chain

    Directory of Open Access Journals (Sweden)

    Wilk-Kołodziejczyk D.

    2014-08-01

    Full Text Available This article presents a practical solution in the form of implementation of agent-based platform for the management of contracts in a network of foundries. The described implementation is a continuation of earlier scientific work in the field of design and theoretical system specification for cooperating companies [1]. The implementation addresses key design assumptions - the system is implemented using multi-agent technology, which offers the possibility of decentralisation and distributed processing of specified contracts and tenders. The implemented system enables the joint management of orders for a network of small and medium-sized metallurgical plants, while providing them with greater competitiveness and the ability to carry out large procurements. The article presents the functional aspects of the system - the user interface and the principle of operation of individual agents that represent businesses seeking potential suppliers or recipients of services and products. Additionally, the system is equipped with a bi-directional agent translating standards based on ontologies, which aims to automate the decision-making process during tender specifications as a response to the request.

  10. The Use of Some Forecasting Methods and SWOT Analysis in the Selected Processes of Foundry

    Directory of Open Access Journals (Sweden)

    Szymszal J.

    2017-12-01

    Full Text Available Forecasting and analysis SWOT are helping tools in the business activity, because under conditions of dynamic changes in both closer and more distant surroundings, reliable, forward-looking information and trends analysis are playing a decisive role. At present, the ability to use available data in forecasting and other analyzes according with changes in business environment are the key managerial skills required, since both forecasting and SWOT analysis are a integral part of the management process, and the appropriate level of forecasting knowledge is increasingly appreciated. Examples of practical use of some forecasting methods in optimization of the procurement, production and distribution processes in foundries are given. The possibilities of using conventional quantitative forecasting methods based on econometric and adaptive models applying the creep trend and harmonic weights are presented. The econometric models were additionally supplemented with the presentation of error estimation methodology, quality assessment and statistical verification of the forecast. The possibility of using qualitative forecasts based on SWOT analysis was also mentioned.

  11. Sessile macro-epibiotic community of solitary ascidians, ecosystem engineers in soft substrates of Potter Cove, Antarctica

    Directory of Open Access Journals (Sweden)

    Clara Rimondino

    2015-01-01

    Full Text Available The muddy bottoms of inner Potter Cove, King George Island (Isla 25 de Mayo, South Shetlands, Antarctica, show a high density and richness of macrobenthic species, particularly ascidians. In other areas, ascidians have been reported to play the role of ecosystem engineers, as they support a significant number of epibionts, increasing benthic diversity. In this study, a total of 21 sessile macro-epibiotic taxa present on the ascidian species Corella antarctica Sluiter, 1905, Cnemidocarpa verrucosa (Lesson, 1830 and Molgula pedunculata Herdman, 1881 were identified, with Bryozoa being the most diverse. There were differences between the three ascidian species in terms of richness, percent cover and diversity of sessile macro-epibionts. The morphological characteristics of the tunic surface, the available area for colonization (and its relation with the age of the basibiont individuals and the pH of the ascidian tunic seem to explain the observed differences. Recent environmental changes in the study area (increase of suspended particulate matter caused by glaciers retreat have been related to observed shifts in the benthic community structure, negatively affecting the abundance and distribution of the studied ascidian species. Considering the diversity of sessile macro-epibionts found on these species, the impact of environmental shifts may be greater than that estimated so far.

  12. Geothermal investment analysis with site-specific applications to Roosevelt Hot Springs and Cove Fort-Sulphurdale, Utah

    Energy Technology Data Exchange (ETDEWEB)

    Cassel, T.A.V.; Edelstein, R.H.; Blair, P.D.

    1978-12-01

    The analysis and modeling of investment behavior in the development of hydrothermal electric power facilities are reported. This investment behavior reflects a degree of sensitivity to public policy alternatives concerning taxation and regulation of the resource and its related energy conversion facilities. The objective of the current research is to provide a realistic and theoretically sound means for estimating the impacts of such public policy alternatives. A stochastic simulation model was developed which offers an efficient means for site-specific investment analysis of private sector firms and investors. The results of the first year of work are discussed including the identification, analysis, quantification and modeling of: a decision tree reflecting the sequence of procedures, timing and stochastic elements of hydrothermal resource development projects; investment requirements, expenses and revenues incurred in the exploration, development and utilization of hydrothermal resources for electric power generation; and multiattribute investment decision criteria of the several types of firms in the geothermal industry. An application of the investment model to specific resource sites in the state of Utah is also described. Site specific data for the Known Geothermal Resource Areas of Roosevelt Hot Springs and Cove Fort-Sulphurdale are given together with hypothesized generation capacity growth rates.

  13. Geochronology of the Swift Current granite and host volcanic rocks of the Love Cove group, southwestern Avalon zone, Newfoundland

    International Nuclear Information System (INIS)

    Dallmeyer, R.D.; O'Driscoll, C.F.; Hussey, E.M.

    1981-01-01

    Zircon fractions from the variably deformed and metamorphosed Swift Current granite and host volcanic rocks of the Love Cove Group record individually discordant U-Pb ages with well-defined upper concordia intercept ages of 580 +- 20 and 590 +- 30 Ma, respectively. These are interpreted to be crystallization dates and indicate a late Proterozoic cogmagmatic relationship. Primary hornblende from the pluton record disturbed 40 Ar/ 39 Ar age spectra that suggest postcrystallization argon loss, probably during Acadian (Devonian) regional metamorphism. 40 Ar/ 39 Ar plateau ages of 560-566 Ma are well defined for the hornblende and are interpreted to date times of postmagmatic cooling. The similarity between zircon and hornblende dates suggests relatively rapid postmagmatic cooling. A six-point, Rb-Sr whole-rock isochron age of 548 +- 11 Ma is defined for the pluton. The slight discordancy of this date in comparison with the zircon and hornblende ages may reflect a minor disturbance of whole-rock isotopic systems during Acadian regional metamorphism. (author)

  14. Monitoring of heavy metal particle emission in the exhaust duct of a foundry using LIBS

    International Nuclear Information System (INIS)

    Dutouquet, C.; Le Bihan, O.; Dermigny, A.; Frejafon, E.; Gallou, G.; Sirven, J.B.; Torralba, B.

    2014-01-01

    Heavy metals have long been known to be detrimental to human health and the environment.Their emission is mainly considered to occur via the atmospheric route. Most of airborne heavy metals are of anthropogenic origin and produced through combustion processes at industrial sites such as incinerators and foundries. Current regulations impose threshold limits on heavy metal emissions. The reference method currently implemented for quantitative measurements at exhaust stacks consists of on-site sampling of heavy metals on filters for the particulate phase (the most prominent and only fraction considered in this study) prior to subsequent laboratory analysis. Results are therefore known only a few days after sampling. Stiffer regulations require the development of adapted tools allowing automatic, on-site or even in-situ measurements with temporal resolutions. The Laser-Induced Breakdown Spectroscopy (LIBS) technique was deemed as a potential candidate to meet these requirements. On site experiments were run by melting copper bars and monitoring emission of this element in an exhaust duct at a pilot-scale furnace in a French research center dedicated to metal casting. Two approaches designated as indirect and direct analysis were broached in these experiments. The former corresponds to filter enrichment prior to subsequent LIBS interrogation whereas the latter entails laser focusing right through the aerosol for detection. On-site calibration curves were built and compared with those obtained at laboratory scale in order to investigate possible matrix and analyte effects. Eventually, the obtained results in terms of detection limits and quantitative temporal monitoring of copper emission clearly emphasize the potentialities of the direct LIBS measurements. (authors)

  15. Engineering properties of concrete with partial utilization of used foundry sand.

    Science.gov (United States)

    Manoharan, Thiruvenkitam; Laksmanan, Dhamothiran; Mylsamy, Kaliyannan; Sivakumar, Pandian; Sircar, Anirbid

    2018-01-01

    Solid wastes generated from manufacturing industries are increasing at an alarming rate and it is consistently increasing. One such industrial solid waste is Used Foundry Sand (UFS). On the other hand, fine aggregates involved in the concrete are generally river sand, which is scarce, high cost and excavation of the river sand that promote environmental degradation. So, there is an urge to find some alternative solution to dispose UFS and to limit the use of river sand. In this research work, river sand was partially replaced by UFS. The percentage replacements were 0, 5, 10, 15, 20 and 25 wt% respectively. Experimental investigations were carried out to evaluate the mechanical, durability and micro-structural properties of M20 concrete at the age of 7, 28 and 91 day. XRD (X-ray Diffraction), EDX (Energy Dispersive X-ray) and optical-microscopic imaging analysis were performed to identify the presence of various compounds and micro cracks in the concrete with UFS. Comparative studies on control mix against trial mix were carried out. It was found that compression strength, flexural strength and modulus of elasticity were approximately constant up to 20 wt% UFS and decreased with further addition. Whereas, split tensile strength was increased after 20 wt% addition but it affects the other properties of concrete. The durability test results showed that the resistance of concrete against abrasion and rapid chloride permeability of the concrete mixture containing UFS up to 20 wt% were almost similar to the values of control mix. The findings suggest that UFS can effectively replace river sand. However, it is recommended that the replacement should not exceed 20 wt%. Copyright © 2017. Published by Elsevier Ltd.

  16. Monitoring of heavy metal particle emission in the exhaust duct of a foundry using LIBS.

    Science.gov (United States)

    Dutouquet, C; Gallou, G; Le Bihan, O; Sirven, J B; Dermigny, A; Torralba, B; Frejafon, E

    2014-09-01

    Heavy metals have long been known to be detrimental to human health and the environment. Their emission is mainly considered to occur via the atmospheric route. Most of airborne heavy metals are of anthropogenic origin and produced through combustion processes at industrial sites such as incinerators and foundries. Current regulations impose threshold limits on heavy metal emissions. The reference method currently implemented for quantitative measurements at exhaust stacks consists of on-site sampling of heavy metals on filters for the particulate phase (the most prominent and only fraction considered in this study) prior to subsequent laboratory analysis. Results are therefore known only a few days after sampling. Stiffer regulations require the development of adapted tools allowing automatic, on-site or even in-situ measurements with temporal resolutions. The Laser-Induced Breakdown Spectroscopy (LIBS) technique was deemed as a potential candidate to meet these requirements. On site experiments were run by melting copper bars and monitoring emission of this element in an exhaust duct at a pilot-scale furnace in a French research center dedicated to metal casting. Two approaches designated as indirect and direct analysis were broached in these experiments. The former corresponds to filter enrichment prior to subsequent LIBS interrogation whereas the latter entails laser focusing right through the aerosol for detection. On-site calibration curves were built and compared with those obtained at laboratory scale in order to investigate possible matrix and analyte effects. Eventually, the obtained results in terms of detection limits and quantitative temporal monitoring of copper emission clearly emphasize the potentialities of the direct LIBS measurements. Copyright © 2014 Elsevier B.V. All rights reserved.

  17. Mechanical and toxicological evaluation of concrete artifacts containing waste foundry sand.

    Science.gov (United States)

    Mastella, Miguel Angelo; Gislon, Edivelton Soratto; Pelisser, Fernando; Ricken, Cláudio; da Silva, Luciano; Angioletto, Elídio; Montedo, Oscar Rubem Klegues

    2014-08-01

    The creation of metal parts via casting uses molds that are generally made from sand and phenolic resin. The waste generated after the casting process is called waste foundry sand (WFS). Depending on the mold composition and the casting process, WFS can contain substances that prevent its direct emission to the environment. In Brazil, this waste is classified according to the Standard ABNT NBR 10004:2004 as a waste Class II (Non-Inert). The recycling of this waste is limited because its characteristics change significantly after use. Although the use (or reuse) of this byproduct in civil construction is a technically feasible alternative, its effects must be evaluated, especially from mechanical and environmental points of view. Thus, the objective of this study is to investigate the effect of the use of WFS in the manufacture of cement artifacts, such as masonry blocks for walls, structural masonry blocks, and paving blocks. Blocks containing different concentrations of WFS (up to 75% by weight) were produced and evaluated using compressive strength tests (35 MPa at 28 days) and toxicity tests on Daphnia magna, Allium cepa (onion root), and Eisenia foetida (earthworm). The results showed that there was not a considerable reduction in the compressive strength, with values of 35 ± 2 MPa at 28 days. The toxicity study with the material obtained from leaching did not significantly interfere with the development of D. magna and E. foetida, but the growth of the A. cepa species was reduced. The study showed that the use of this waste in the production of concrete blocks is feasible from both mechanical and environmental points of view. Copyright © 2014 Elsevier Ltd. All rights reserved.

  18. Exploring Mission Concepts with the JPL Innovation Foundry A-Team

    Science.gov (United States)

    Ziemer, John K.; Ervin, Joan; Lang, Jared

    2013-01-01

    The JPL Innovation Foundry has established a new approach for exploring, developing, and evaluating early concepts called the A-Team. The A-Team combines innovative collaborative methods with subject matter expertise and analysis tools to help mature mission concepts. Science, implementation, and programmatic elements are all considered during an A-Team study. Methods are grouped by Concept Maturity Level (CML), from 1 through 3, including idea generation and capture (CML 1), initial feasibility assessment (CML 2), and trade space exploration (CML 3). Methods used for each CML are presented, and the key team roles are described from two points of view: innovative methods and technical expertise. A-Team roles for providing innovative methods include the facilitator, study lead, and assistant study lead. A-Team roles for providing technical expertise include the architect, lead systems engineer, and integration engineer. In addition to these key roles, each A-Team study is uniquely staffed to match the study topic and scope including subject matter experts, scientists, technologists, flight and instrument systems engineers, and program managers as needed. Advanced analysis and collaborative engineering tools (e.g. cost, science traceability, mission design, knowledge capture, study and analysis support infrastructure) are also under development for use in A-Team studies and will be discussed briefly. The A-Team facilities provide a constructive environment for innovative ideas from all aspects of mission formulation to eliminate isolated studies and come together early in the development cycle when they can provide the biggest impact. This paper provides an overview of the A-Team, its study processes, roles, methods, tools and facilities.

  19. Correlation between airborne manganese concentration at the workstations in the iron foundry and manganese concentration in workers’ blood

    Directory of Open Access Journals (Sweden)

    Seyedtaghi Mirmohammadi

    2017-08-01

    Full Text Available Background: Manganese (Mn used as raw material for melting process in the ferrous foundry is considered as hazardous neurotoxic substance because it accumulates in the central nervous system and may cause neurological disorders. The furnace-men and melting department workers are potentially exposed to manganese particles or fume in the workplace. The objective of the research has been to investigate the sources and levels of manganese exposure in the foundry by correlation of blood-manganese (B-Mn and air-manganese (air-Mn measurement. Material and Methods: Air-Mn and Mn of blood serum were measured involving workers who worked in a big-sized foundry during 1 year. The standard method of the Occupational Safety and Health Administration (OSHA ID-121 was used for air and blood assessment and atomic absorption spectroscopy (AAS was carried out for air and blood sample analysis. Results: The air sampling results have revealed that there is a high exposure to manganese (4.5 mg/m3 in the workplace as compared to the National Institute for Occupational Safety and Health’s (NIOSH time weighted average (the reference time-weighted average (TWA = 1 mg/m3. The average blood serum Mn concentration was 2.745 μg/l for subjects working for shorter than 3 months and 274.85 μg/l for subjects working 3–12 months. Conclusions: Against the research hypothesis there was no correlation between the air-Mn concentration and the B-Mn (serum level of manganese in the serum of the exposed subjects. It may be due to short time of air sampling of manganese airborne particles, and a real-time monitoring of airborne manganese particles is suggested for any future study. Med Pr 2017;68(4:449–458

  20. Optimization as investment decision support in a Swedish medium-sized iron foundry - A move beyond traditional energy auditing

    International Nuclear Information System (INIS)

    Thollander, Patrik; Mardan, Nawzad; Karlsson, Magnus

    2009-01-01

    Due to increased globalisation, industries are facing greater competition that is pressing companies into decreasing their expenses in order to increase their profits. As regards Swedish industry, it has been faced with substantial increases in energy prices in recent years. Barriers to energy efficiency such as imperfect information inhibit investments in energy efficiency measures, energy audits being one means of reducing barriers and overcoming imperfect information. However, an evaluation of such energy audits in Sweden reveals that it is chiefly low-cost measures that are undertaken as a result of an audit. Moreover, these audits often tend to focus on support processes such as ventilation, lighting, air compressors etc., while measures impacting production processes are often not as extensively covered, which underlines the need for further support in addition to energy audits. Decision support is practised in a variety of different disciplines such as optimization and simulation and the aim of this paper is to explore whether investment decision support practices may be used successfully towards small and medium-sized manufacturers in Sweden when complex production-related investment decisions are taken. The optimization results from the different cases, involving a foundry's investment in a new melting unit, indicate that with no electricity price fluctuations over the day, the investment seems sound as it lowers the overall energy costs. However, with fluctuating electricity prices, there are no large differences in energy costs between the option of retaining the existing five melting furnaces at the foundry and investing in a twin furnace and removing the holding furnaces - which was the initial investment plan for the foundry in the study. It would not have been possible to achieve this outcome without the use of investment decision support such as MIND. One of the main conclusions in this paper is that investment decision support, when strategic

  1. Characterization and extraction of gold contained in foundry industrial wastes; Caracterizacion y extraccion de oro contenido en matrices de desechos industriales de fundicion

    Energy Technology Data Exchange (ETDEWEB)

    Vite T, J; Vite T, M; Diaz C, A; Carreno de Leon, C [Instituto Nacional de Investigaciones Nucleares, Depto. de Estudios del Ambiente, A.P. 18-1027, 11801 Mexico D.F. (Mexico)

    1999-07-01

    Gold was characterized and leached in foundry sands. These wastes are product among others of the automotive industry where they are used as molds material which are contaminated by diverse metals during the foundry. To fulfil the leaching process four coupled thermostat columns were used. To characterize the solid it was used the X-ray diffraction technique. For the qualitative analysis it was used the Activation analysis technique. Finally, for the study of liquors was used the Plasma diffraction spectroscopy (Icp-As) technique. The obtained results show that the process which was used the thermostat columns was more efficient, than the methods traditionally recommended. (Author)

  2. Estimates of Nutrient Loading by Ground-Water Discharge into the Lynch Cove Area of Hood Canal, Washington

    Science.gov (United States)

    Simonds, F. William; Swarzenski, Peter W.; Rosenberry, Donald O.; Reich, Christopher D.; Paulson, Anthony J.

    2008-01-01

    field investigations show that ground-water discharge into the Lynch Cove area of Hood Canal is highly dynamic and strongly affected by the large tidal range. In areas with a steep shoreline and steep hydraulic gradient, ground-water discharge is spatially concentrated in or near the intertidal zone, with increased discharge during low tide. Topographically flat areas with weak hydraulic gradients had more spatial variability, including larger areas of seawater recirculation and more widely dispersed discharge. Measured total-dissolved-nitrogen concentrations in ground water ranged from below detection limits to 2.29 milligrams per liter and the total load entering Lynch Cove was estimated to be approximately 98 ? 10.3 metric tons per year (MT/yr). This estimate is based on net freshwater seepage rates from Lee-type seepage meter measurements and can be compared to estimates derived from geochemical tracer mass balance estimates (radon and radium) of 231 to 749 MT/yr, and previous water-mass-balance estimates (14 to 47 MT/ yr). Uncertainty in these loading estimates is introduced by complex biogeochemical cycles of relevant nutrient species, the representativeness of measurement sites, and by energetic dynamics at the coastal aquifer-seawater interface caused by tidal forcing.

  3. Property enhancement by grain refinement of zinc-aluminium foundry alloys

    International Nuclear Information System (INIS)

    Krajewski, W K; Piwowarski, G; Krajewski, P K; Greer, A L

    2016-01-01

    Development of cast alloys with good mechanical properties and involving less energy consumption during their melting is one of the key demands of today's industry. Zinc foundry alloys of high and medium Al content, i.e. Zn-(15-30) wt.% Al and Zn-(8-12) wt.% Al, can satisfy these requirements. The present paper summarizes the work [1-9] on improving properties of sand-cast ZnAl10 (Zn-10 wt.% Al) and ZnAl25 (Zn-25 wt. % Al) alloys by melt inoculation. Special attention was devoted to improving ductility, whilst preserving high damping properties at the same time. The composition and structural modification of medium- and high-aluminium zinc alloys influence their strength, tribological properties and structural stability. In a series of studies, Zn - (10-12) wt. % Al and Zn - (25-26) wt.% Al - (1-2.5) wt.% Cu alloys have been doped with different levels of added Ti. The melted alloys were inoculated with ZnTi-based refiners and it was observed that the dendritic structure is significantly finer already after addition of 50 - 100 ppm Ti to the melted alloys. The alloy's structure and mechanical properties have been studied using: SEM (scanning electron microscopy), LM (light microscopy), dilatometry, pin-on-disc wear, and tensile strength measurements. Grain refinement leads to significant improvement of ductility in the binary high-aluminium Zn-(25-27) Al alloys while in the medium-aluminium alloys the effect is rather weak. In the ternary alloys Zn-26Al-Cu, replacing a part of Cu with Ti allows dimensional changes to be reduced while preserving good tribological properties. Furthermore, the high initial damping properties were nearly entirely preserved after inoculation. The results obtained allow us to characterize grain refinement of the examined high-aluminium zinc alloys as a promising process leading to the improvement of their properties. At the same time, using low melting ZnTi-based master alloys makes it possible to avoid the excessive melt

  4. Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

    Directory of Open Access Journals (Sweden)

    Nirmala D.B.

    2016-06-01

    Full Text Available This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37 Orthogonal Arrays (OA with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering “Nominal the better” situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

  5. Experimental study of optimal self compacting concrete with spent foundry sand as partial replacement for M-sand using Taguchi approach

    Science.gov (United States)

    Nirmala, D. B.; Raviraj, S.

    2016-06-01

    This paper presents the application of Taguchi approach to obtain optimal mix proportion for Self Compacting Concrete (SCC) containing spent foundry sand and M-sand. Spent foundry sand is used as a partial replacement for M-sand. The SCC mix has seven control factors namely, Coarse aggregate, M-sand with Spent Foundry sand, Cement, Fly ash, Water, Super plasticizer and Viscosity modifying agent. Modified Nan Su method is used to proportion the initial SCC mix. L18 (21×37) Orthogonal Arrays (OA) with the seven control factors having 3 levels is used in Taguchi approach which resulted in 18 SCC mix proportions. All mixtures are extensively tested both in fresh and hardened states to verify whether they meet the practical and technical requirements of SCC. The quality characteristics considering "Nominal the better" situation is applied to the test results to arrive at the optimal SCC mix proportion. Test results indicate that the optimal mix satisfies the requirements of fresh and hardened properties of SCC. The study reveals the feasibility of using spent foundry sand as a partial replacement of M-sand in SCC and also that Taguchi method is a reliable tool to arrive at optimal mix proportion of SCC.

  6. Correlation between work process-related exposure to polycyclic aromatic hydrocarbons and urinary levels of alpha-naphthol, beta-naphthylamine and 1-hydroxypyrene in iron foundry workers

    DEFF Research Database (Denmark)

    Hansen, Åse Marie; Omland, Øyvind; Poulsen, O M

    1994-01-01

    foundry workers. Hand molders, finishing workers and truck drivers tended to have the highest levels. Concerning alpha-naphthol the highest concentrations were measured in urine from casters and shake-out workers. With regard to epidemiologic studies demonstrating that molders and casters have a higher...

  7. Benthic diatoms from Potter Cove, 25 de Mayo (King George) Island, Antarctica: Mucilage and glucan storage as a C-source for limpets

    Science.gov (United States)

    Daglio, Yasmin; Sacristán, Hernán; Ansaldo, Martín; Rodríguez, María C.

    2018-03-01

    Biofilms were allowed to develop on ceramic tiles placed in closed containers on the shore of Potter Cove, 25 de Mayo (King George) Island. Water pumping from the cove inside the containers extended for 25 days. Diatoms were the dominant microalgae in these biofilms, which were removed from a set of tiles to a) characterize the extracellular mucilage, b) carry out floristic determination and c) perform grazing experiments with the limpet Nacella concinna. Biofilms mucilaginous matrix consisted of proteins and carbohydrates. Room temperature aqueous extraction of the freeze-dried material rendered a fraction enriched in the storage glucan chrysolaminarin, its identity confirmed by methylation structural analyses. Hot water extracted products showed greater heterogeneity in monosaccharide composition, including glucose, mannose, galactose, fucose, xylose and rhamnose. Diatom identification revealed that Pseudogomphonema kamtschaticum was the dominant species followed by several Navicula species, Nitzschia pellucida and Synedra kerguelensis. Photographical survey of colonized tiles placed in glass flasks together with a specimen of Nacella concinna exhibited between 5 and 30% removal of the biofilms coverage after 24 h of exposure to the limpet, suggesting that EPS and chrysolaminarin constitute a C-source for the gastropod.

  8. Summary of public participation : Environmental impact assessment : Proposal by the New Brunswick Power Commission to refurbish the Coleson Cove generating station

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2002-09-01

    A proposal was made by New Brunswick (NB) Power for the refurbishment of the Coleson Cove generating station, to the Public Utilities Board (PUB). It was determined by the PUB that a requirement existed for 1050 megawatt (MW) of power at Coleson Cove. This document presented a summary of public participation. Two meetings were held in support of the Environmental Impact Assessment (EIA). Several concerns were raised by various groups at both meetings. Some of the issues discussed included: (1) Orimulsion{sup R} fuel, reputed to be the dirtiest fuel in the world, (2) fuel supply, (3) project agenda, (4) project costs and others. It appeared that most of the participants in the public consultation process were against the proposal. It was felt that the emissions of sulphur dioxide and nitrous oxide should be considered in the greater context of reducing present and future emissions of greenhouse gases. The participants recommended that the New Brunswick government support a 400 MW combined cycle natural gas turbine unit instead of the proposal under review. Much opposition to the project concerned the potential degradation of the environment and the health of the citizens. Environmental representatives were concerned since the Solid Waste Management Area would be located in the vicinity of a proposed marine and wildlife sanctuary. Industry representatives were eager for the opportunities offered by the proposal. refs.

  9. Proposed stratotype for the base of the highest Cambrian stage at the first appearance datum of Cordylodus andresi, Lawson Cove section, Utah, USA

    Science.gov (United States)

    Miller, J.F.; Ethington, Raymond L.; Evans, K.R.; Holmer, L.E.; Loch, James D.; Popov, L.E.; Repetski, J.E.; Ripperdan, R.L.; Taylor, John F.

    2006-01-01

    We propose a candidate for the Global Standard Stratotype-section and Point (GSSP) for the base of the highest stage of the Furongian Series of the Cambrian System. The section is at Lawson Cove in the Ibex area of Millard County, Utah, USA. The marker horizon is the first appearance datum (FAD) of the conodont Cordylodus andresi Viira et Sergeyeva in Kaljo et al. [Kaljo, D., Borovko, N., Heinsalu, H., Khazanovich, K., Mens, K., Popov, L., Sergeyeva, S., Sobolevskaya, R., Viira, V., 1986. The Cambrian-Ordovician boundary in the Baltic-Ladoga clint area (North Estonia and Leningrad Region, USSR). Eesti NSV Teaduste Akadeemia Toimetised. Geologia 35, 97-108]. At this section and elsewhere this horizon also is the FAD of the trilobite Eurekia apopsis (Winston et Nicholls, 1967). This conodont characterizes the base of the Cordylodus proavus Zone, which has been recognized in many parts of the world. This trilobite characterizes the base of the Eurekia apopsis Zone, which has been recognized in many parts of North America. The proposed boundary is 46.7 m above the base of the Lava Dam Member of the Notch Peak Formation at the Lawson Cove section. Brachiopods, sequence stratigraphy, and carbon-isotope geochemistry are other tools that characterize this horizon and allow it to be recognized in other areas. ?? 2006 Nanjing Institute of Geology and Palaeontology, CAS.

  10. Lung cancer risk in welders and foundry workers with a history of heavy smoking in the USA: The National Lung Screening Trial.

    Science.gov (United States)

    Wong, Jason Y Y; Bassig, Bryan A; Seow, Wei Jie; Hu, Wei; Ji, Bu-Tian; Blair, Aaron; Silverman, Debra T; Lan, Qing

    2017-06-01

    Foundry work is a risk factor for lung cancer; however, the association with welding is unclear, as smoking is common among metalworkers and may mask the relationship. We evaluated whether history of welding and foundry work, independently and jointly, and employment duration were associated with lung cancer risk in heavy smokers. We analysed data from the National Lung Screening Trial, a prospective randomised trial of 53 454 heavy smokers (>30 pack-years) in the USA. Cox regression models were used to estimate the HRs and 95% CIs of medically/histologically confirmed incident lung cancer during the follow-up period (2002-2009) in relation to history and duration of welding and foundry work assessed via questionnaires, adjusted for screening arm, component study, sex, age, race/ethnicity, education, smoking status and pack-years, body mass index and personal/family medical history. There were 2034 incident lung cancer cases throughout the follow-up. Increasing years of employment in welding (p-trend =0.039) and foundry work (p-trend =0.005) were related to increased lung cancer risk among heavy smokers. Having ever been employed (≥1 yr) as either a welder or foundry worker alone was associated with non-significant increased risks of lung cancer (HR=1.12 (95% CI 0.91 to 1.37) and HR=1.09 (95% CI 0.85 to 1.39), respectively). Further, there was a joint-effect in that those who were ever employed in both occupations had significantly increased risks (HR=1.48 (95% CI 1.08 to 2.04)). Our findings provide further evidence that exposure to welding/metal fumes may be associated with elevated lung cancer risk. NCT00047385. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

  11. Use of Solid Waste (Foundry Slag) Mortar and Bamboo Reinforcement in Seismic Analysis for Single Storey Masonry Building

    Science.gov (United States)

    Ahmad, S.; Husain, A.; Ghani, F.; Alam, M. N.

    2013-11-01

    The conversion of large amount of solid waste (foundry slag) into alternate source of building material will contribute not only as a solution to growing waste problem, but also it will conserve the natural resources of other building material and thereby reduce the cost of construction. The present work makes an effort to safe and economic use of recycle mortar (1:6) as a supplementary material. Conventional and recycled twelve prisms were casted with varying percentage of solid waste (foundry slag) added (0, 10, 20, 30 %) replacing cement by weight and tested under compression testing machine. As the replacement is increasing, the strength is decreasing. 10 % replacement curve is very closed to 0 % whereas 20 % is farther and 30 % is farthest. 20 % replacement was chosen for dynamic testing as its strength is within permissible limit as per IS code. A 1:4 scale single storey brick model with half size brick was fabricated on shake table in the lab for dynamic testing using pure friction isolation system (coarse sand as friction material µ = 0.34). Pure friction isolation technique can be adopted economically in developing countries where low-rise building prevails due to their low cost. The superstructure was separated from the foundation at plinth level, so as to permit sliding of superstructure during severe earthquake. The observed values of acceleration and displacement responses compare fairly with the analytical values of the analytical model. It also concluded that 20 % replacement of cement by solid waste (foundry slag) could be safely adopted without endangering the safety of the masonry structures under seismic load.To have an idea that how much energy is dissipated through this isolation, the same model with fixed base was tested and results were compared with the isolated free sliding model and it has been observed that more than 60 % energy is dissipated through this pure friction isolation technique. In case of base isolation, no visible cracks

  12. No evidence of increased risk of soft tissue sarcomas in the neighborhood of a steel foundry in Verona

    Directory of Open Access Journals (Sweden)

    Marta Benedetti

    2010-12-01

    Full Text Available The aim of the present study was to evaluate the possible association between occurrence of soft tissue sarcomas in Verona (Italy and residence near a steel foundry, whose emissions of dioxin-like compounds may be relevant. Exposure to total suspended particulate (TSP emitted from the plant as estimated by ADMS-urban dispersion model was used as an indirect index of exposure to dioxin-like compounds. Verona municipality was divided in six subareas according to the decreasing levels of estimated TSP exposure, and soft tissue sarcomas cases were mapped according to residence at time of diagnosis. Standardized incidence ratios were computed. No statistically significant departures between observed and expected cases were detected as illustrated by trend-test results.

  13. Monolithic silicon photonics in a sub-100nm SOI CMOS microprocessor foundry: progress from devices to systems

    Science.gov (United States)

    Popović, Miloš A.; Wade, Mark T.; Orcutt, Jason S.; Shainline, Jeffrey M.; Sun, Chen; Georgas, Michael; Moss, Benjamin; Kumar, Rajesh; Alloatti, Luca; Pavanello, Fabio; Chen, Yu-Hsin; Nammari, Kareem; Notaros, Jelena; Atabaki, Amir; Leu, Jonathan; Stojanović, Vladimir; Ram, Rajeev J.

    2015-02-01

    We review recent progress of an effort led by the Stojanović (UC Berkeley), Ram (MIT) and Popović (CU Boulder) research groups to enable the design of photonic devices, and complete on-chip electro-optic systems and interfaces, directly in standard microelectronics CMOS processes in a microprocessor foundry, with no in-foundry process modifications. This approach allows tight and large-scale monolithic integration of silicon photonics with state-of-the-art (sub-100nm-node) microelectronics, here a 45nm SOI CMOS process. It enables natural scale-up to manufacturing, and rapid advances in device design due to process repeatability. The initial driver application was addressing the processor-to-memory communication energy bottleneck. Device results include 5Gbps modulators based on an interleaved junction that take advantage of the high resolution of the sub-100nm CMOS process. We demonstrate operation at 5fJ/bit with 1.5dB insertion loss and 8dB extinction ratio. We also demonstrate the first infrared detectors in a zero-change CMOS process, using absorption in transistor source/drain SiGe stressors. Subsystems described include the first monolithically integrated electronic-photonic transmitter on chip (modulator+driver) with 20-70fJ/bit wall plug energy/bit (2-3.5Gbps), to our knowledge the lowest transmitter energy demonstrated to date. We also demonstrate native-process infrared receivers at 220fJ/bit (5Gbps). These are encouraging signs for the prospects of monolithic electronics-photonics integration. Beyond processor-to-memory interconnects, our approach to photonics as a "More-than- Moore" technology inside advanced CMOS promises to enable VLSI electronic-photonic chip platforms tailored to a vast array of emerging applications, from optical and acoustic sensing, high-speed signal processing, RF and optical metrology and clocks, through to analog computation and quantum technology.

  14. arena_cove.grd

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NGDC builds and distributes high-resolution, coastal digital elevation models (DEMs) that integrate ocean bathymetry and land topography to support NOAA's mission to...

  15. Lithogenic and biogenic particle deposition in an Antarctic coastal environment (Marian Cove, King George Island): Seasonal patterns from a sediment trap study

    Science.gov (United States)

    Khim, B. K.; Shim, J.; Yoon, H. I.; Kang, Y. C.; Jang, Y. H.

    2007-06-01

    Particulate suspended material was recovered over a 23-month period using two sediment traps deployed in shallow water (˜30 m deep) off the King Sejong Station located in Marian Cove of King George Island, West Antarctica. Variability in seasonal flux and geochemical characteristics of the sediment particles highlights seasonal patterns of sedimentation of both lithogenic (terrigenous) and biogenic particles in the coastal glaciomarine environment. All components including total mass flux, lithogenic particle flux and biogenic particle flux show distinct seasonal variation, with high recovery rates during the summer and low rates under winter fast ice. The major contributor to total mass flux is the lithogenic component, comprising from 88% during the summer months (about 21 g m -2 d -1) up to 97% during the winter season (about 2 g m -2 d -1). The lithogenic particle flux depends mainly on the amount of snow-melt (snow accumulation) delivered into the coastal region as well as on the resuspension of sedimentary materials. These fine-grained lithogenic particles are silt-to-clay sized, composed mostly of clay minerals weathered on King George Island. Biogenic particle flux is also seasonal. Winter flux is ˜0.2 g m -2 d -1, whereas the summer contribution increases more than tenfold, up to 2.6 g m -2 d -1. Different biogenic flux between the two summers indicates inter-annual variability to the spring-summer phytoplankton bloom. The maximum of lithogenic particle flux occurs over a short period of time, and follows the peak of biogenic particle flux, which lasts longer. The seasonal warming and sea-ice retreat result in change in seawater nutrient status and subsequent ice-edge phytoplankton production. Meanwhile, the meltwater input to Marian Cove from the coastal drainage in January to February plays a major role in transporting lithogenic particles into the shallow water environment, although the tidal currents may be the main agents of resuspension in this

  16. Environmental characterization foundry sands used in sanitary landfills; Caracterizacao ambiental de areias descartadas de fundicao utilizadas na cobertura de residuos em aterros sanitarios

    Energy Technology Data Exchange (ETDEWEB)

    Domingues, L.G.F.; Ferreira, G.C.S.; Pires, M.S.G.; Teixeira, I.; Carnin, R.; Sarro, W.S., E-mail: lucienegferrari@gmail.com [Universidade Estadual de Campinas (UNICAMP), SP (Brazil)

    2016-07-01

    The national solid waste policy recommends reducing solid waste generation and reusing them in different applications. Preliminary studies show that the foundry sand generated from cast metal parts undercut, has excellent applicability in grain size stabilization of soils for geotechnical functions, and therefore, should not be discarded as waste. This study aimed at environmental characterization of two lots of waste foundry sand (WFS), from different industries, to the particle size stabilization of a clayey soil for use in coverage of solid waste in landfills. The methodology included physicochemical characterization tests (grain size, permeability, XRF and heavy metals) and environmental (NBR 10004: 2004, NBR 10005: 2004, NBR 10006: 20004 and acute toxicity with Vibrio fischeri). The results prove the environmental viability of using these lots of WFS as functional material in the composition of landfills. (author)

  17. Metallurgy and foundry practice. German-English. With 40,000 citations. Metallurgie und Giessereitechnik. Deutsch-Englisch. Mit etwa 40,000 Wortstellen

    Energy Technology Data Exchange (ETDEWEB)

    Stoelzel, K [ed.

    1986-01-01

    The dictionary represents the German-English terminology of the broad field of metallurgy (the dressing of ores and fluxes, pig iron and steel making, powder and nonferrous metallurgy, forming processes etc.) as well as of the broad field of foundry practice. Apart from the theoretical fundamental principles emphasis is on the problems of materials working and materials testing. Moreover, the dictionary considers a number of technical terms concerning the hardening, surface treatment and corrosion of materials.

  18. Alpha spectrometric characterization of process-related particle size distributions from active particle sampling at the Los Alamos National Laboratory uranium foundry

    Energy Technology Data Exchange (ETDEWEB)

    Plionis, Alexander A [Los Alamos National Laboratory; Peterson, Dominic S [Los Alamos National Laboratory; Tandon, Lav [Los Alamos National Laboratory; Lamont, Stephen P [Los Alamos National Laboratory

    2009-01-01

    Uranium particles within the respirable size range pose a significant hazard to the health and safety of workers. Significant differences in the deposition and incorporation patterns of aerosols within the respirable range can be identified and integrated into sophisticated health physics models. Data characterizing the uranium particle size distribution resulting from specific foundry-related processes are needed. Using personal air sampling cascade impactors, particles collected from several foundry processes were sorted by activity median aerodynamic diameter onto various Marple substrates. After an initial gravimetric assessment of each impactor stage, the substrates were analyzed by alpha spectrometry to determine the uranium content of each stage. Alpha spectrometry provides rapid nondestructive isotopic data that can distinguish process uranium from natural sources and the degree of uranium contribution to the total accumulated particle load. In addition, the particle size bins utilized by the impactors provide adequate resolution to determine if a process particle size distribution is: lognormal, bimodal, or trimodal. Data on process uranium particle size values and distributions facilitate the development of more sophisticated and accurate models for internal dosimetry, resulting in an improved understanding of foundry worker health and safety.

  19. Evaluation of Synthetic Gypsum Recovered via Wet Flue-Gas Desulfurization from Electric Power Plants for Use in Foundries

    Directory of Open Access Journals (Sweden)

    R. Biernacki

    2012-09-01

    Full Text Available This article investigates possible use of waste gypsum (synthetic, recovered via flue-gas desulfurization from coal-fired electric powerplants, in foundries. Energy sector, which in Eastern Europe is mostly composed from coal-fired electric power plants, is one of the largestproducers of sulfur dioxide (SO2.In order to protect the environment and reduce the amount of pollution flue-gas desulfurization (FGD is used to remove SO2 fromexhaust flue gases of fossil-fuel power plants. As a result of this process gypsum waste is produced that can be used in practicalapplications.Strength and permeability tests have been made and also in-depth analysis of energy consumption of production process to investigateways of preparing the synthetic gypsum for casting moulds application. This paper also assesses the chemical composition, strength andpermeability of moulds made with synthetic gypsum, in comparison with moulds made with traditional GoldStar XL gypsum and withceramic molds. Moreover examination of structure of synthetic gypsum, the investigations on derivatograph and calculations of energyconsumption during production process of synthetic gypsum in wet flue-gas desulfurization were made.After analysis of gathered data it’s possible to conclude that synthetic gypsum can be used as a material for casting mould. There is nosignificant decrease in key properties, and on the other hand there is many additional benefits including low energy consumption,decreased cost, and decreased environmental impact.

  20. Conditions of Thermal Reclamation Process Realization on a Sample of Spent Moulding Sand from an Aluminum Alloy Foundry Plant

    Directory of Open Access Journals (Sweden)

    Łucarz M.

    2017-06-01

    Full Text Available The results of investigations of thermal reclamation of spent moulding sands originating from an aluminum alloy foundry plant are presented in this paper. Spent sands were crushed by using two methods. Mechanical fragmentation of spent sand chunks was realized in the vibratory reclaimer REGMAS. The crushing process in the mechanical device was performed either with or without additional crushing-grinding elements. The reclaimed material obtained in this way was subjected to thermal reclamations at two different temperatures. It was found that a significant binder gathering on grain surfaces favors its spontaneous burning, even in the case when a temperature lower than required for the efficient thermal reclamation of furan binders is applied in the thermal reclaimer. The burning process, initiated by gas burners in the reclaimer chamber, generates favorable conditions for self-burning (at a determined amount of organic binders on grain surfaces. This process is spontaneously sustained and decreases the demand for gas. However, due to the significant amount of binder, this process is longer than in the case of reclaiming moulding sand prepared with fresh components.

  1. Using mixture design of experiments to assess the environmental impact of clay-based structural ceramics containing foundry wastes

    Energy Technology Data Exchange (ETDEWEB)

    Coronado, M. [Department of Chemistry and Process and Resources Engineering, University of Cantabria, 39005 Santander (Spain); Department of Materials and Ceramics Engineering (CICECO), University of Aveiro, 3810-193 Aveiro (Portugal); Segadães, A.M. [Department of Materials and Ceramics Engineering (CICECO), University of Aveiro, 3810-193 Aveiro (Portugal); Andrés, A., E-mail: andresa@unican.es [Department of Chemistry and Process and Resources Engineering, University of Cantabria, 39005 Santander (Spain)

    2015-12-15

    Highlights: • Modelling of the environmental risk in terms of clay and by-products contents. • M-DoE and response surface plots enable quick comparison of three ceramic processes. • Basicity of the mixture increases the leaching, especially at low firing temperatures. • Liquid phase content plays a major role decreasing the leaching of Cr and Mo. • Together, M-DoE and phase diagrams enable better prediction of pollutants leaching. - Abstract: This work describes the leaching behavior of potentially hazardous metals from three different clay-based industrial ceramic products (wall bricks, roof tiles, and face bricks) containing foundry sand dust and Waelz slag as alternative raw materials. For each product, ten mixtures were defined by mixture design of experiments and the leaching of As, Ba, Cd, Cr, Cu, Mo, Ni, Pb, and Zn was evaluated in pressed specimens fired simulating the three industrial ceramic processes. The results showed that, despite the chemical, mineralogical and processing differences, only chrome and molybdenum were not fully immobilized during ceramic processing. Their leaching was modeled as polynomial equations, functions of the raw materials contents, and plotted as response surfaces. This brought to evidence that Cr and Mo leaching from the fired products is not only dependent on the corresponding contents and the basicity of the initial mixtures, but is also clearly related with the mineralogical composition of the fired products, namely the amount of the glassy phase, which depends on both the major oxides contents and the firing temperature.

  2. Optimising a Model of Minimum Stock Level Control and a Model of Standing Order Cycle in Selected Foundry Plant

    Directory of Open Access Journals (Sweden)

    Szymszal J.

    2013-09-01

    Full Text Available It has been found that the area where one can look for significant reserves in the procurement logistics is a rational management of the stock of raw materials. Currently, the main purpose of projects which increase the efficiency of inventory management is to rationalise all the activities in this area, taking into account and minimising at the same time the total inventory costs. The paper presents a method for optimising the inventory level of raw materials under a foundry plant conditions using two different control models. The first model is based on the estimate of an optimal level of the minimum emergency stock of raw materials, giving information about the need for an order to be placed immediately and about the optimal size of consignments ordered after the minimum emergency level has occurred. The second model is based on the estimate of a maximum inventory level of raw materials and an optimal order cycle. Optimisation of the presented models has been based on the previously done selection and use of rational methods for forecasting the time series of the delivery of a chosen auxiliary material (ceramic filters to a casting plant, including forecasting a mean size of the delivered batch of products and its standard deviation.

  3. West and East

    Directory of Open Access Journals (Sweden)

    Alexander Rappaport

    2017-12-01

    Full Text Available The topic “West-East” has a clear cultural and historical meaning. Orthodox temples face East. The way from West to East and from East to West is tens of thousands of kilometers long and has a special meaning. It differs from the way from North to South: the horizontal axes connect regions, while the vertical axis (Earth-Sky connects the worlds. The expansion of Eurasian tribes occurred along the East-West axis – the world horizontal way. Today the cultural memory of people in the East and West finds itself in the theatre of new dramas of existence and new forces. With the advances in electronic technologies, the world movements seem to have sunk in the depth of the chthonian past to come up anew to the surface of fantastic speeds and momentary connections. A new type of planetary landscape-space relation appears, giving no place for West and East.

  4. JPRS Report, East Europe

    National Research Council Canada - National Science Library

    1988-01-01

    Partial Contents: East Europe, Party Activities, Socialist Party, Freedom Fighters, Education, Youth Training, Historian, Death Penalty, Peace Making Duties, Socialism, Communism, Economics, Restructuring...

  5. East African Medical Journal

    African Journals Online (AJOL)

    The East African Medical Journal is intended for publication of papers on ... research on problems relevant to East Africa and other African countries will receive special ... Analysis of survival patterns of TB‐HIV co‐infected patients in relation to ...

  6. Middle East Respiratory Syndrome

    Centers for Disease Control (CDC) Podcasts

    2014-07-07

    This podcast discusses Middle East Respiratory Syndrome, or MERS, a viral respiratory illness caused by Middle East Respiratory Syndrome Coronavirus—MERS-CoV.  Created: 7/7/2014 by National Center for Immunization and Respiratory Diseases (NCIRD).   Date Released: 7/7/2014.

  7. Middle East - future perspectives

    International Nuclear Information System (INIS)

    Lior, Y.

    1997-01-01

    Facts concerning the basic features of Tlatelolco Treaty are discussed in comparison with the Middle East situation which is described as a special case. Countries in the Middle East should attain political, social and ideological maturity necessary for the adoption of negotiating strategies suitable for this particular region

  8. A study on EUV reticle surface molecular contamination under different storage conditions in a HVM foundry fab

    Science.gov (United States)

    Singh, SherJang; Yatzor, Brett; Taylor, Ron; Wood, Obert; Mangat, Pawitter

    2017-03-01

    The prospect of EUVL (Extreme Ultraviolet Lithography) insertion into HVM (High Volume Manufacturing) has never been this promising. As technology is prepared for "lab to fab" transition, it becomes important to comprehend challenges associated with integrating EUVL infrastructure within existing high volume chip fabrication processes in a foundry fab. The existing 193nm optical lithography process flow for reticle handling and storage in a fab atmosphere is well established and in-fab reticle contamination concerns are mitigated with the reticle pellicle. However EUVL reticle pellicle is still under development and if available, may only provide protection against particles but not molecular contamination. HVM fab atmosphere is known to be contaminated with trace amounts of AMC's (Atmospheric Molecular Contamination). If such contaminants are organic in nature and get absorbed on the reticle surface, EUV photon cause photo-dissociation resulting into carbon generation which is known to reduce multilayer reflectivity and also degrades exposure uniformity. Chemical diffusion and aggregation of other ions is also reported under the e-beam exposure of a EUV reticle which is known to cause haze issues in optical lithography. Therefore it becomes paramount to mitigate absorbed molecular contaminant concerns on EUVL reticle surface. In this paper, we have studied types of molecular contaminants that are absorbed on an EUVL reticle surface under HVM fab storage and handling conditions. Effect of storage conditions (gas purged vs atmospheric) in different storage pods (Dual pods, Reticle Clamshells) is evaluated. Absorption analysis is done both on ruthenium capping layer as well as TaBN absorber. Ru surface chemistry change as a result of storage is also studied. The efficacy of different reticle cleaning processes to remove absorbed contaminant is evaluated as well.

  9. Use of wasted foundry sand (WFS) as a partial substitute for silica in a soda lime glass; Utilizacao de areia descartada de fundicao (ADF) como substituinte parcial da silica em um vidro soda-cal

    Energy Technology Data Exchange (ETDEWEB)

    Martin, A.C.; Ueno, O.K.; Folgueras, M.V., E-mail: amandacarolinemartin@gmail.com [Universidade do Estado de Santa Catarina (CCT/UDESC), Joinville, SC (Brazil). Centro de Ciencias Tecnologicas

    2016-07-01

    The waste foundry sand (WFS) is the main waste generates in foundry industries. Studies in the literature suggest the use of WFS in different materials, such as concrete, brick or asphalt. This work aims to partially replace the silica of a soda-lime glass by the WFS. The waste foundry sand has in its composition elements such as iron and aluminum that can affect the glass quality, which justifies the residue processing to reduce the impurity content. The treatments, that included mechanical agitation and thermal treatment, resulted in a slight decrease in the percent of iron with consequent increase of the silica content. After treatment, some sands were incorporated into the glass, that showed green color but with lower absorption intensity for the sand with less iron content. It was observed that it's possible to obtain glasses using WFS, however, there is difficulty in color controlling. (author.

  10. EAST AFRICAN MEDICAL JOURNAL

    African Journals Online (AJOL)

    2003-11-11

    Nov 11, 2003 ... East African Medical Journal Vol. ... Lecturer/Consultant Surgeon, Paediatric Surgery Unit, Department of Surgery, College of Medical Sciences, University of Calabar, .... mind and the results obtained were however satisfying.

  11. Fluxus East / Petra Stegmann

    Index Scriptorium Estoniae

    Stegmann, Petra

    2008-01-01

    Näitusest "Fluxus East" Kumu Kunstimuuseumis. Fluxuse liikumisest leedu kunstniku George Maciunase (1931-1978) eestvedamisel. Liikumise ilmingutest Eestis (happeningid, muusikaaktsioonid, visuaalne poeesia, mail art). Kuraator Petra Stegmann, kujundaja Andrea Pichl

  12. Leukaemia in East Suffolk

    International Nuclear Information System (INIS)

    Bush, M.F.H.

    1983-09-01

    An investigation was conducted by the East Suffolk Health Authority to determine whether there were any geographical variations in the incidence of leukaemia over the last fifteen years in East Suffolk suggesting an environmental hazard, e.g. Sizewell Power Station. No areas were found to have a statistically significant increased incidence of leukaemia cases although there did appear to be a cluster of cases in the Leiston area. (U.K.)

  13. Ergonomic Improvements for Foundries

    Energy Technology Data Exchange (ETDEWEB)

    Frank Peters; Patrick Patterson

    2002-06-18

    The goal of this project was to make improvements to the production systems of the steel casting industry through ergonomic improvements. Because of the wide variety of products, the wide range of product sizes, and the relatively small quantities of any particular product, manual operations remain a vital part of the production systems of the steel casting companies. Ergonomic improvements will assist the operators to more efficiently and consistently produce quality products.

  14. World review: Middle East

    International Nuclear Information System (INIS)

    Anon.

    2000-01-01

    The article gives information on contracts announced (and to whom) and recently completed in some parts of the Middle East in the petroleum, natural gas and petrochemicals industries. Areas specifically mentioned are Bahrain, Egypt, Iran, Libya, Oman, Qatar, Saudi Arabia, Syria and the United Arab Emirates. The prospects for the petrochemical industry in particular are good and continued growth is expected. Gas is likely to make an increasingly important contribution to the prosperity of the Middle East and is expected to carry a higher priority than expansion of crude oil production

  15. Environmental impact of some trace elements emission from the work environment of Atbara Cement Factory and Atbara Railway Foundry

    Energy Technology Data Exchange (ETDEWEB)

    Nimir, S A.M. [University of Khartoum, Faculty of Education, Department of Chemistry, Khartoum (Sudan)

    2006-06-15

    This work was performed to evaluate the chemical pollution level by some trace elements at the work environment of Atbara Cement Factory (ACF) and Atbara Railway Foundry (ARF). Samples of soil and air were collected from the two sites study, ACF and ARF. To assess the environmental impact of these industrial complexes, the samples were collected from sites expected to be free from industrial emission to serve as control. Plant samples were also collected from (ACF) and the control site. The samples were analyzed and the concentrations of K, Na, Mn, Fe, Cu, Zu and Pb were determined using three analytical techniques: Atomic absorption spectroscopy (AAS), X-ray fluorescence (X RF), and flame emission photometry (FEP). Soil samples were chemically fractionated using separation methods and the solutions were analyzed using AAS methods and FEP to determine the chemical form of the elements. The quality of the data was achieved through the analysis of certified reference materials. The results of this study were compared with previous literature. The data were treated by calculating enrichment factor and statistically by multivariate analysis such as, principle component analysis and cluster analysis. The findings of the study were concluded as follows. The effect of emission from both sites is very clear when the concentrations of the studied trace elements in soil and air samples are compared with the respective concentrations at the control site. Higher values of these elements are found at ARF and slightly high at ACF. The elements which can be attributed to industrial emission are noticeably higher at ARF, for example Cu is forty times as higher as compared to the control site. While Zn is slightly high and Pb is very high. The same remarks are further confirmed by enrichment factor calculation. For soil samples enrichment factor was obtained for two groups of elements, the enriched group includes the elements Pb, Cu and Zn which have enrichment factors higher in

  16. Environmental impact of some trace elements emission from the work environment of Atbara Cement Factory and Atbara Railway Foundry

    International Nuclear Information System (INIS)

    Nimir, S.A.M.

    2006-06-01

    This work was performed to evaluate the chemical pollution level by some trace elements at the work environment of Atbara Cement Factory (ACF) and Atbara Railway Foundry (ARF). Samples of soil and air were collected from the two sites study, ACF and ARF. To assess the environmental impact of these industrial complexes, the samples were collected from sites expected to be free from industrial emission to serve as control. Plant samples were also collected from (ACF) and the control site. The samples were analyzed and the concentrations of K, Na, Mn, Fe, Cu, Zu and Pb were determined using three analytical techniques: Atomic absorption spectroscopy (AAS), X-ray fluorescence (X RF), and flame emission photometry (FEP). Soil samples were chemically fractionated using separation methods and the solutions were analyzed using AAS methods and FEP to determine the chemical form of the elements. The quality of the data was achieved through the analysis of certified reference materials. The results of this study were compared with previous literature. The data were treated by calculating enrichment factor and statistically by multivariate analysis such as, principle component analysis and cluster analysis. The findings of the study were concluded as follows. The effect of emission from both sites is very clear when the concentrations of the studied trace elements in soil and air samples are compared with the respective concentrations at the control site. Higher values of these elements are found at ARF and slightly high at ACF. The elements which can be attributed to industrial emission are noticeably higher at ARF, for example Cu is forty times as higher as compared to the control site. While Zn is slightly high and Pb is very high. The same remarks are further confirmed by enrichment factor calculation. For soil samples enrichment factor was obtained for two groups of elements, the enriched group includes the elements Pb, Cu and Zn which have enrichment factors higher in

  17. Middle East political stability

    OpenAIRE

    2008-01-01

    Henry Siegman asks whether the next US President can rescue a two-state solution to the Israel–Palestine conflict; Lakhdar Brahimi discusses Iran – war or peace in the Middle East?; Eric Rouleau assesses the Iranian nuclear threat; Walid Khadduri looks at concerns over the future of Iraq and regional implications.

  18. East Asian welfare regime

    DEFF Research Database (Denmark)

    Abrahamson, Peter

    2017-01-01

    The paper asks if East Asian welfare regimes are still productivist and Confucian? And, have they developed public care policies? The literature is split on the first question but (mostly) confirmative on the second. Care has to a large, but insufficient extent, been rolled out in the region...

  19. Fleet Readiness Center East

    Science.gov (United States)

    ability to take care of our Customers, our People, and our Business. WHAT'S NEW ON FACEBOOK? weather icon S o cial Media Navy Twitter US Navy Pinterest US Navy Instagram FRC East Facebook US Navy Google FRCE ADVERSE WEATHER INFO Severe Weather Number: 252-464-8333 Visit us on Facebook for up-to-date

  20. Middle East Respiratory Syndrome (MERS)

    Science.gov (United States)

    Middle East Respiratory Syndrome Coronavirus; MERS-CoV; Novel coronavirus; nCoV ... for Disease Control and Prevention website. Middle East Respiratory Syndrome (MERS): Frequently asked questions and answers. www. ...

  1. JPRS Report, East Europe

    Science.gov (United States)

    1990-05-04

    ments, they actively advertise their readiness to enter 90GE0031A East Berlin A USSENWIRTSCHAFT a barter deal and they will accept it as long as...AG it comprises the following aspects: has set up two joint ventures in the USSR producing shoes; Adidas has one joint venture in Hungary.) Joint...administration until product development, advertising , and marketing. In the repayment of long-term credits. Consortiums addition, the Soviet firm is interested

  2. Ground water contamination with (238)U, (234)U, (235)U, (226)Ra and (210)Pb from past uranium mining: cove wash, Arizona.

    Science.gov (United States)

    Dias da Cunha, Kenya Moore; Henderson, Helenes; Thomson, Bruce M; Hecht, Adam A

    2014-06-01

    in the majority of the water samples, indicating more than one source of contamination could contribute to the sampled sources. The effective doses due to ingestion of the minimum uranium concentrations in water samples exceed the average dose considering inhalation and ingestion of regular diet for other populations around the world (1 μSv/year). The maximum doses due to ingestion of (238)U or (234)U were above the international limit for effective dose for members of the public (1 mSv/year), except for inhabitants of two chapters. The highest effective dose was estimated for inhabitants of Cove, and it was almost 20 times the international limit for members of the public. These results indicate that ingestion of water from some of the sampled sources poses health risks.

  3. Drugs in East Germany.

    Science.gov (United States)

    Dressler, J; Müller, E

    1997-09-01

    Germany was divided into two parts after World War II. The closed border and a nonconvertible currency in the Eastern part were the factors that did not allow a drug market to develop. Alcohol and medicaments were used as substitute drugs. Since Germany was reunified 5 years ago, there are now the same conditions prevailing for the procurement and sale of drugs in East Germany as there are in the Western German states. This report describes the current state of drug traffic, especially in Saxony, under the new social conditions.

  4. Climatic variability of east Malaysia

    International Nuclear Information System (INIS)

    Camerlengo, A.L.; Saadon, M.N.; Awang, M.; Somchit, H.; Rang, L.Y.

    2001-01-01

    The objective of this paper is to learn the variability of atmospheric pressure, relative humidity and insolation in East Malaysia. The main results of our study are: (1) a gentle pressure gradient is observed at the east coast in the boreal winter, (2) smaller atmospheric pressure values are noted during the first inter-monsoon period all across East Malaysia, (3) lesser insolation values are observed in Sarawak and at the east coast during the boreal winter as compared to the boreal summer, and (4) a poleward increase of insolation is registered. (author)

  5. Automação industrial e sistemas informatizados de gestão da produção em fundições de mercado Industrial automation and computerized production management systems in make-to-order foundries

    Directory of Open Access Journals (Sweden)

    Flavio Cesar F. Fernandes

    2002-12-01

    Full Text Available Fundição é um processo de fabricação que vem crescendo em importância. O principal objetivo deste artigo é analisar, em termos de automação e sistemas informatizados de gestão da produção (SIGP, as fundições de mercado (fundições que produzem sob encomenda um grande número de pedidos vindos, em geral, de um grande número de clientes no interior do Estado de São Paulo pertencentes aos 5 principais pólos (Piracicaba, Indaiatuba, Limeira, São Carlos e Itu com 10 a 250 trabalhadores. Das 61 empresas do interior de São Paulo, 35 situam-se nesses 5 pólos (ou em suas imediações; entrevistamos pessoalmente os diretores industriais e visitamos o chão de fábrica de 30 fundições dentre essas 35. Analisamos quase 200 tabelas de freqüência e de contingência e extraímos várias conclusões, por exemplo: (i entre os três principais problemas e necessidades relativos à produção, dois deles estão diretamente relacionados com a automação industrial e com os SIGP; (ii são coincidentes os interesses em automação e SIGP.Foundry is a manufacturing process with a growing importance. The main objective of this paper is to analyze, in terms of automation and of computerized production management systems (CPMS, the make-to-order foundry in the interior of the state of São Paulo belonging to 5 main foundry industrial districts (Piracicaba, Indaiatuba, Limeira, São Carlos and Itu with 10 to 250 workers. From the 61 enterprises in the interior of São Paulo State, 35 are situated in these 5 industrial districts (or in their neighborhood; we interviewed personally the industrial executive officer and visited the shop-floor of 30 among this 35 foundries. We have analyzed almost 200 frequency and contingency tables and draw several conclusions, for example: (i among the three main problems and necessities related with production, two of them are directly related with automation and CPMS; (ii automation and CPMS generate coincident

  6. The Danish East India Company

    DEFF Research Database (Denmark)

    Sørensen, Karsten Engsig

    2005-01-01

    The article analysis the first Danish East India Company incorporated in 1616, which was the first Danish Stock Company and which has impacts even on modern Danish company la......The article analysis the first Danish East India Company incorporated in 1616, which was the first Danish Stock Company and which has impacts even on modern Danish company la...

  7. Middle East gas

    International Nuclear Information System (INIS)

    Thomas, V.

    2001-01-01

    Despite the significant contribution of the Middle East countries of Bahrain, Iran, Iraq, Kuwait, Qatar, Saudi Arabia and the United Arab Emirates in the Arabia Gulf to the world's oil output, they are placing increasing emphasis on natural gas as a source of exports and to fuel domestic economic growth. The region accounts for 35% of the world's proven gas resource base, with Iran and Qatar holding major reserves. The region is becoming increasingly important in global liquefied natural gas (LNG) trade and details of key LNG projects and the major players in this area are given; a key advantage is the region's position between the two main markets - the Asia Pacific and the Atlantic Basin. Brief details are also given of gas pipeline projects and gas-to-liquid (GTL) projects in the region

  8. [Health risk assessment of exposure to metals in the workers of the steel foundry and in the general population of Taranto (Italy)].

    Science.gov (United States)

    Soleo, Leonardo; Lovreglio, Piero; Panuzzo, Laura; D'Errico, Maria Nicolà; Basso, Antonella; Gilberti, Maria Enrica; Drago, Ignazio; Tomasi, Cesare; Apostoli, Pietro

    2012-01-01

    To study the urinary excretion of As, Cr, Mn, Co, Ni, Cu, Zn, Cd, Sn, Ba, Hg, Pb, Sb in workers at the Taranto integrated-cycle steel foundry and in subjects from the general population of Taranto, to assess the health risk posed by occupational exposure and environmental exposure, respectively, to these metals. The study included 49 steel foundry workers (exposed), working in the minerals and agglomerates pools, steel processing plants 1 and 2 and maritime plants, and 50 subjects belonging to the general population of Taranto resident at various distances from the factory (controls), randomly selected from the exposed subjects and controls enrolled in previous research conducted in 2005. A questionnaire was administered to all participants, enquiring into general characteristics, lifestyle, diet, and any medical conditions. Informed written consent to take part in the study was obtained from all subjects before enrolment. The results of environmental monitoring performed in 2005 in the workers' sectors, consisting of determining As, Cr, Mn, Ni, Cu, Zn, Cd and Pb in the respirable dust, revealed by both samplers applied in fixed positions and personal samplers, were considered. Urine samples were obtained from all participants on a Friday, to determine As and Cr by AAS and all the other metal elements by a multielement technique with ICP-MS. Urinary creatinine was also determined to make any necessary adjustments. All urine analyses were performed in 2005 within one month of urine collection. In the respirable dust, As and Cd were always within the LOD, whereas Cr, Mn, Ni, Cu and Pb were 1-2 orders of magnitude below the respective TLV-TWA of the ACGIH. Mn was the only metal element that presented significantly higher urinary concentrations in exposed subjects as compared to controls, although the values in both groups were in any case within the Italian reference range. Co, Cu, Zn, Sn and Sb showed significantly higher urinary concentrations in controls than in

  9. East India Company Logbooks - Images

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — This collection consists of images of 1,235 ship logbooks created during British East India Company voyages. Period of record 1786-1834, peaking in 1804. The...

  10. Heavy-metal contamination of soils in Saxony/Germany by foundry fumes and low-cost rapid analyses of contaminated soils by XRF

    Science.gov (United States)

    Mucke, D.

    2012-04-01

    Heavy-metal contamination of soils in Saxony/Germany by foundry fumes and low-cost rapid analysis of contaminated soils by XRF Dieter Mucke, Rolf Kumann, Sebastian Baldauf GEOMONTAN Gesellschaft für Geologie und Bergbau mbH&Co.KG, Muldentalstrasse 56, 09603 Rothenfurth, Saxony/Germany For hundreds of years in the Ore Mountains between Bohemia and Saxony silver and other ores are produced and smelted. Sulphide- and sulpharsenide-ores needed to be roasted first. In doing so the sulphide sulphur was oxidised under formation of sulphur dioxide SO2 and arsenide conversed into elemental arsenic and arsenide trioxide As2O3 respectively. Also the metals lead, cadmium and zinc are components of hut smokes, in the field of nickel foundries also nickel. The contents of soils basically reflect the geogenic conditions, which are caused by decomposition- and relocation-effects of the mineralisations, in the area of foundries also with influences by with the hut smokes anthropogenic mobilised elements. The Saxonian Agency for Environment and Geology drafted in 1992 a Soil Investigation Program with the aim of investigation of the contamination of Saxonian soils with arsenic and toxic heavy metals. In order of this Agency GEOMONTAN investigated 1164 measuring points in the grid 4 * 4 km.soil profiles and extracted soil samples for analysis. In the result of the laboratory examinations the Agency edited the "Soil atlas of the Free State of Saxony". 27 elements, pH and PAK are shown in detailed maps and allow in whole Saxony the first assessment of the contamination of soils with arsenic and toxic heavy metals. Each of the investigated soil profiles represent an area of 16 km2. Already by the different use of the districts (agricultural, industrial, urban) restricts representative values. GEOMONTAN in the meantime used at the exploration of a copper deposit in Brandenburg/Germany with approx. 50,000 single tests at drill cores a very fast low-cost method: the X Ray fluorescence

  11. Nuclear power in East Asia

    International Nuclear Information System (INIS)

    Abelson, P.H.

    1996-01-01

    This editorial discusses the shifting dominance in the nuclear reactor technology from the USA to new leadership in East Asia. With the expanding economies and electricity demand, Design, construction and operation of a large number of nuclear power plants in east Asia will support nuclear engineers, technologist, manufacturing facilities, and potential weapons experts. In contrast, the cessation of construction of power reactors in the US is leading to deminished nuclear capabilities

  12. ISSN 2073 ISSN 2073-9990 East Cent. East Cent. East Cent. Afr. J.

    African Journals Online (AJOL)

    DELL

    East and Central African Journal of Surgery. ... collaboration in the writing and editing of Surgical Care at the District Hospital, ... increasing availability of computers and huge developments in software technology such ... Emergency Surgery ...

  13. Forests of East Texas, 2014

    Science.gov (United States)

    Thomas J. Brandeis

    2015-01-01

    This resource update provides an overview of forest resources in east Texas derived from an inventory conducted by the U.S. Forest Service, Forest Inventory and Analysis (FIA) Program at the Southern Research Station in cooperation with the Texas A&M Forest Service. These estimates are based on field data collected using the FIA annualized sample design and are...

  14. Forests of east Texas, 2013

    Science.gov (United States)

    K.J.W. Dooley; T.J. Brandeis

    2014-01-01

    This resource update provides an overview of forest resources in east Texas based on an inventory conducted by the U.S. Forest Service, Forest Inventory and Analysis (FIA) program at the Southern Research Station in cooperation with the Texas A&M Forest Service. Forest resource estimates are based on field data collected using the FIA annualized sample design and...

  15. Forests of east Texas, 2016

    Science.gov (United States)

    Kerry Dooley

    2018-01-01

    This resource update provides an overview of forest resources in east Texas based on an inventory conducted by the U.S. Forest Service, Forest Inventory and Analysis (FIA) program at the Southern Research Station (SRS) in cooperation with Texas A&M Forest Service. The 254 counties of Texas are consolidated into seven FIA survey units—Southeast (unit 1),...

  16. East African Orthopaedic Journal: Submissions

    African Journals Online (AJOL)

    Author Guidelines. The East African Orthopaedic Journal is published biannually by the Kenya Orthopaedics Association. Its primary objective is to give researchers in orthopaedics and ... Format should be as follows; Details of authors as for original articles, summary of not more than 200 words, introduction, case report,

  17. East African Journal of Statistics: Journal Sponsorship

    African Journals Online (AJOL)

    East African Journal of Statistics: Journal Sponsorship. Journal Home > About the Journal > East African Journal of Statistics: Journal Sponsorship. Log in or Register to get access to full text downloads.

  18. Multinationals and East Asian Integration | IDRC - International ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    ... and the United States, in the recent and rapid economic growth and integration in East Asia. ... "dragons" of East Asia have emerged among the world's leading economic powers. ... Asian outlook: New growth dependent on new productivity.

  19. Ergonomic Improvements for Foundries; FINAL

    International Nuclear Information System (INIS)

    Frank Peters; Patrick Patterson

    2002-01-01

    The goal of this project was to make improvements to the production systems of the steel casting industry through ergonomic improvements. Because of the wide variety of products, the wide range of product sizes, and the relatively small quantities of any particular product, manual operations remain a vital part of the production systems of the steel casting companies. Ergonomic improvements will assist the operators to more efficiently and consistently produce quality products

  20. Middle East and North African Oil.

    Science.gov (United States)

    Al-Quazzaz, Ayad

    1981-01-01

    Traces the history of oil and natural gas in the Middle East and relates the importance of the Middle East's current stores of oil to economic development. Information is presented on the relationship of major oil companies and local governments, OPEC, rate of production, and the impact of oil on the societies of the Middle East and North Africa.…

  1. Scopus: Journal of East African Ornithology

    African Journals Online (AJOL)

    Scopus: Journal of East African Ornithology has been published since 1977 by the Bird Committee of the East Africa Natural History Society. Originally titled Scopus, the addition of Journal of East African Ornithology began with our January 2018 issue. The journal is published Open Access twice a year, typically in January ...

  2. Funding problems threaten Middle East's synchrotron

    CERN Multimedia

    McCabe, H

    1999-01-01

    Scientists will tour the Middle East to try to raise support for the Synchrotron radiation for Experimental Science and Applications in the Middle East project. The plan is to dismantle and move a decommissioned synchrotron from Berlin to the Middle East where scientists of any nationality would be able to use it (3 paragraphs).

  3. Portulacaria afra in East AFrica | Newton | Journal of East African ...

    African Journals Online (AJOL)

    No Abstract. East African Journal of Natural History Vol. 96 (1) 2007: pp. 107-108. http://dx.doi.org/10.2982/0012-8317(2007)96[107:PAIEA]2.0.CO;2 · AJOL African Journals Online. HOW TO USE AJOL... for Researchers · for Librarians · for Authors · FAQ's · More about AJOL · AJOL's Partners · Terms and Conditions of Use ...

  4. Energy supply in East Germany

    Energy Technology Data Exchange (ETDEWEB)

    Shimoyama, Tsutomu

    1988-07-10

    East Germany has abundant brown coal, about 90.4% of primary energy production in 1986. The high dependence upon brown coal has been established since its reevaluation in 1980 and the production is reaching a peak. Its share in power generation is also as high as 83.3% in the year. Therefore, the energy sufficiency of East Germany is about 80%. Problems are arising, however, in deterioration of excavation conditions and coal quality. Domestic energy resources such as the uranium and natural gas are also used to the maximum extent. The nuclear power has about 10% of share in the power generation. The share expansion policy is seemingly maintained even after the accident of Chernoble. Exploration, excavation and reprocessing of the uranium are conducted under the leadership of USSR. The country depends upon the oil in a very low level, less than 1%, as a result of the energy conservation policy in 1980's. (1 fig, 5 tabs)

  5. East African Cenozoic vegetation history.

    Science.gov (United States)

    Linder, Hans Peter

    2017-11-01

    The modern vegetation of East Africa is a complex mosaic of rainforest patches; small islands of tropic-alpine vegetation; extensive savannas, ranging from almost pure grassland to wooded savannas; thickets; and montane grassland and forest. Here I trace the evolution of these vegetation types through the Cenozoic. Paleogene East Africa was most likely geomorphologically subdued and, as the few Eocene fossil sites suggest, a woodland in a seasonal climate. Woodland rather than rainforest may well have been the regional vegetation. Mountain building started with the Oligocene trap lava flows in Ethiopia, on which rainforest developed, with little evidence of grass and none of montane forests. The uplift of the East African Plateau took place during the middle Miocene. Fossil sites indicate the presence of rainforest, montane forest and thicket, and wooded grassland, often in close juxtaposition, from 17 to 10 Ma. By 10 Ma, marine deposits indicate extensive grassland in the region and isotope analysis indicates that this was a C 3 grassland. In the later Miocene rifting, first of the western Albertine Rift and then of the eastern Gregory Rift, added to the complexity of the environment. The building of the high strato-volcanos during the later Mio-Pliocene added environments suitable for tropic-alpine vegetation. During this time, the C 3 grassland was replaced by C 4 savannas, although overall the extent of grassland was reduced from the mid-Miocene high to the current low level. Lake-level fluctuations during the Quaternary indicate substantial variation in rainfall, presumably as a result of movements in the intertropical convergence zone and the Congo air boundary, but the impact of these fluctuations on the vegetation is still speculative. I argue that, overall, there was an increase in the complexity of East African vegetation complexity during the Neogene, largely as a result of orogeny. The impact of Quaternary climatic fluctuation is still poorly understood

  6. East Asia basin Analysis Project

    International Nuclear Information System (INIS)

    Terman, M.J.

    1986-01-01

    The United Nations-related Committee for Coordination of Joint Prospecting for Mineral Resources in Asian Offshore Areas (CCOP), in cooperation with the International Union of Geological Sciences and Circum-Pacific Council, is implementing the East Asia Basin Analysis Project. National and regional organizations, principally members of the ASEAN Council of Petroleum, are compiling maps at a scale of 1:2 million and stratigraphic cross sections of basins, with particular initial emphasis on defining and assessing oil and gas plays and with later analytical focus on other sedimentary minerals (e.g., coal, phosphate, evaporites, and uranium). Completion is anticipated in 1988. Two major elements of the project are being contributed from other agencies. (1) Base maps. - The US Geological Survey (USGS) has partly compiled eight sheets covering east Asia that show bathymetry, shorelines, and drainage systems. One sheet also presents topography and selected cultural features. All sheets are scheduled to be completed in 1987. (2) Geotectonic maps. - The Working Group on Studies of East Asian Tectonics and Resources (SEATAR) is now completing 10 transect studies with crustal profiles and strip maps at a scale of 1:1 million. One map for each transect shows a plate tectonic interpretation. Transect coordinators or others will be encouraged to extrapolate between the strips and complete the geotectonic interpretation (on USGS bases) in 1987. The IGCP Project 220 is also compiling on (USGS bases) the tin and tungsten granites of east Asia, emphasizing geochemical data needed to identify predictive models. Other mapping will probably follow mineral-deposit modeling workshops on ophiolotic chromite and regional symposia on oceanic massive sulfide and subvolcanic gold and base metals. Completion may be possible by 1989

  7. Recent LHCD experiments in EAST

    International Nuclear Information System (INIS)

    Ding, B.J.

    2013-01-01

    LHCD system of 2.45 GHz in EAST has been updated to 4MW in last campaign. Aimed at high confinement (H-mode) plasma in EAST, the LHW-plasma coupling and current drive experiments were continued. Experiments of local gas puffing near LHW antenna shows that gas puffing from electron side is better to improve LHW-plasma coupling than that from ion side. LHCD experiments at high density are also performed, demonstrating that the decrease of current efficiency at high density may be related to the parametric decay instability (PDI) effect. Lithiation and local gas puffing near LHW antenna are utilized so as to sustain H-mode plasma. H-mode plasma is obtained by LHCD with a wide range of parameters: Ip=0.4∼0.8MA, B_t=1.35∼1.81T, n_e=1.5∼2.5x10"1"9 m"-"3, P_L_H_W>=0.5MW. LHW power deposition and driven current profile with C3PO/LUKE are calculated with the experimental parameters, showing that central and large driven current seems not a necessary condition for the H-mode plasma. H-mode is reproduced with CRONOS. Long pulse plasmas, >400s L mode fully driven by LHCD and >30s H-mode with LHCD and ICRF, have been achieved and demonstrated in EAST. (author)

  8. The Middle East population puzzle.

    Science.gov (United States)

    Omran, A R; Roudi, F

    1993-07-01

    An overview is provided of Middle Eastern countries on the following topics; population change, epidemiological transition theory and 4 patterns of transition in the middle East, transition in causes of death, infant mortality declines, war mortality, fertility, family planning, age and sex composition, ethnicity, educational status, urbanization, labor force, international labor migration, refugees, Jewish immigration, families, marriage patterns, and future growth. The Middle East is geographically defined as Bahrain, Egypt, Iraq, Jordan, Kuwait, Lebanon, Oman, Qatar, Saudi Arabia, Syria, United Arab Emirates, Yemen, Gaza and the West Bank, Iran, Turkey, and Israel. The Middle East's population grew very little until 1990 when the population was 43 million. Population was about doubled in the mid-1950s at 80 million. Rapid growth occurred after 1950 with declines in mortality due to widespread disease control and sanitation efforts. Countries are grouped in the following ways: persistent high fertility and declining mortality with low to medium socioeconomic conditions (Jordan, Oman, Syria, Yemen, and the West Bank and Gaza), declining fertility and mortality in intermediate socioeconomic development (Egypt, Lebanon, Turkey, and Iran), high fertility and declining mortality in high socioeconomic conditions (Bahrain, Iraq, Kuwait, Qatar, Saudi Arabia, and the United Arab Emirates), and low fertility and mortality in average socioeconomic conditions (Israel). As birth and death rates decline, there is an accompanying shift from communicable diseases to degenerative diseases and increases in life expectancy; this pattern is reflected in the available data from Egypt, Kuwait, and Israel. High infant and child mortality tends to remain a problem throughout the Middle East, with the exception of Israel and the Gulf States. War casualties are undetermined, yet have not impeded the fastest growing population growth rate in the world. The average fertility is 5 births

  9. The East Midlands in 2006: the demography of the East Midlands

    OpenAIRE

    Lawton, C

    2006-01-01

    The East Midlands in 2006 is the evidence base that was produced to underpin the devleopment of the regional economic strategy, A Flourishing Region. This document presents detailed analysis of the demography of the East Midlands.

  10. Near East/South Asia Report

    National Research Council Canada - National Science Library

    1986-01-01

    .... This report from Near East/South Asia, Algeria, Sudan, Iraq, Israel, Kuwait, Saudi Arabia, Syria, Afghanistan, Bangladesh, India, Iran, and Pakistan, contains articles on Economics, Political Science...

  11. Near East/South Asia Report

    National Research Council Canada - National Science Library

    1986-01-01

    .... This report from Near East/South Asia, Egypt, Libya, Morocco, Tunisia, Israel, Jordan, Lebanon, Syria, Afghanistan, Bangladesh, and Iran contains articles on Political Science, Economics, Regional...

  12. Near East/South Asia Report

    National Research Council Canada - National Science Library

    1986-01-01

    .... This report from Near East/South Asia, Egypt, Libya, Tunisia, Israel, Afghanistan, Bangladesh, Iran, Iraq, and Pakistan contains articles on International, Regional, Political and Economic Issues...

  13. Near East/South Asia Report

    National Research Council Canada - National Science Library

    1986-01-01

    .... This report from the Near East/South Asia, Algeria, Egypt, Tunisia, Israel, Kuwait, Lebanon, Oman, Qatar, Saudi Arabia, Afghanistan and Iran, contains articles on International Affairs, Politics...

  14. Near East/South Asia Report

    National Research Council Canada - National Science Library

    1986-01-01

    .... This report contains articles on the Near East/South Asia, Egypt, Mauritania, Morocco, Tunisia, Israel, Jordan, Kuwait, Oman, Saudi Arabia, United Arab Emirates, Afghanistan, Iran and Pakistan...

  15. East Carnduff Unit: corrosion problems

    Energy Technology Data Exchange (ETDEWEB)

    Banks, C D

    1966-07-01

    Waterflooding of the East Carnduff Unit began in late 1962. The first injection line leak was discovered April 29, 1965. The first 6 leaks in the East Carnduff Unit occurred within a period of less than one month--a very startling and serious warning of pending problems. Analysis of the pipe removed showed a deep pit covered by a severe scale in the piping fitting. Several remedial actions were tried in order to develop the present inhibition program. First, the lines were cleaned as well as possible utilizing rubber pig spheres with normal injection pressure. This proved very effective and 2 passes wiped out most of the scale in the lines. Only one line required acid. After the lines had been cleaned, a water treating rate of an organic amine corrosion inhibitor, 10 ppm of the scale inhibitor, and bactericide at the rate of 40 ppm slugs 2 days per month was initiated. The above treating program is in use at the present time and is maintaining a very low leak frequency. This experience has demonstrated 2 important points in waterflood operations: (1) a bare piping system in warm brine service requires constant attention to insure that it is being kept clean; and (2) reliance cannot be placed on any one method of checking corrosion rates.

  16. Alien smuggling: East to West.

    Science.gov (United States)

    Walsh, J H

    1987-01-01

    This year untold millions of illegal aliens will enter Western Europe, Canada, and the US; in 1986, the US alone made 1.7 million apprehensions. Because of the numbers involved and the hard currency exchanged, alien smuggling has become big business--a lucrative track in desparate human beings. West Germany's open door asylum policy has been a boon to the smugglers, and West Berlin is currently a favored port of entry. The government provides social benefits--apartments, food, a stipend, and clothing--for asylum seekers. Smuggling operations appear to fit 3 categories: 1) state-sponsored alien smugglers, with a sub-category of terrorists; 2) ethnic smugglers with a history of terrorist spinoffs; and 3) independent smugglers, who are profit oriented, and willing to handle ethnic aliens and terrorists. In West Germany, immigration investigations begin at the border. West German officials often know that as they cause the Eastern border to be tightened, the flow will gravitate south toward Austria. Redirecting the trasit of Third Worlders from East Berlin away from West Germany, Sweden, and Denmark will be a stop-gap measure at best. Part of West Germany's immigration problem can be traced to the Basic Law that provides asylum for those who claim persecution (political, racial, ethnic, or religious). Yet, any attempt to change asylum would result in an admission of defeat in the quest for a unified Germany. Should Austria move to tighten its immigration laws, agreements similar to those between East and West Germany will likely follow.

  17. Middle East oil and gas

    International Nuclear Information System (INIS)

    1995-01-01

    This study is intended to shed light on structural changes occurring in six Middle East countries (Iran, Iraq, Kuwait, Qatar, Saudi Arabia and the United Arab Emirates) that can be expected to have a significant impact on their oil and gas industry. These six countries provide 42% of the world's traded crude oil, on which Member countries of the International Energy Agency (IEA) are increasingly dependent. They also contain about 65% and 30% of the world's proven oil and natural gas reserves, respectively, and command a strategic location between Europe and Asia. The Middle East has been one of the most volatile parts of the world where war, revolution and embargoes have caused major upheavals that have led to oil supply disruptions. The oil resources of all six countries were initially developed by international oil companies and all are members of the Organization of the Petroleum Exporting Countries (OPEC). In 1994, their crude oil production capacity was about 23 million barrels per day (mbd) and is planned to expand to about 28 mbd by the year 2000. Revenue from the sale of oil accounts for more than 80% of each nation's total exports and about 75% of each government's income. The objectives of this study are: to detail their announced oil and gas development plans, to describe the major trends occurring in these countries, to outline the government responses to the trends, and to analyse the impact of government policies on oil and gas development. (J.S.). 121 refs., 136 figs., 212 tabs

  18. Massive job cuts threaten East German science

    CERN Multimedia

    Hamer, M

    1990-01-01

    German reunification could result in thousands of scientists losing their jobs. At the end of this year the East German state budget for science will run out. Scientists in the East are keen to find Western support to protect their research (1 page).

  19. Journal of East African Natural History

    African Journals Online (AJOL)

    The Journal of East African Natural History is published jointly by the East Africa Natural History Society and the National Museums of Kenya. The Journal publishes papers and notes in the field of natural history, broadly defined as the study of organisms in their natural state, relevant to the eastern African region.

  20. Cultural Foundations of Learning: East and West

    Science.gov (United States)

    Li, Jin

    2012-01-01

    Western and East Asian people hold fundamentally different beliefs about learning that influence how they approach child rearing and education. Reviewing decades of research, Dr. Jin Li presents an important conceptual distinction between the Western mind model and the East Asian virtue model of learning. The former aims to cultivate the mind to…

  1. Green chemistry education in the Middle East

    Science.gov (United States)

    Kolopajlo, Larry

    2017-06-01

    The Middle East once dominated the age of alchemy, and today it is experiencing a resurgence by transforming the age of petroleum chemicals into a greener science through Estidama. This green conversion is taking place through green chemical research and education. This report examines and reviews the understudied subject of green chemical education in the Middle East through the lens of context and history.

  2. Chumbo no sangue de crianças e passivo ambiental de uma fundição de chumbo no Brasil Blood lead levels in children and environmental legacy of a lead foundry in Brazil

    Directory of Open Access Journals (Sweden)

    Fernando Martins Carvalho

    2003-01-01

    Full Text Available OBJETIVO: Determinar os níveis de chumbo no sangue de crianças que moravam próximo a uma fundição de chumbo desativada na Cidade de Santo Amaro da Purificação, Estado da Bahia, em setembro de 1998; e identificar fatores associados à variação destes níveis. MÉTODOS: Estudo de corte transversal com crianças de 1 a 4 anos de idade que residiam a menos de 1 km da fundição. Mães ou responsáveis por 47 crianças responderam questionários sobre transtornos do hábito alimentar (comer barro, terra, reboco ou outros materiais e outros aspectos epidemiológicos relevantes. A concentração de chumbo no sangue foi determinada por espectrofotometria de absorção atômica. RESULTADOS: O nível médio de chumbo foi de 17,1 ± 7,3 mig/dL. Os níveis de chumbo no sangue foram cerca de 5 mig/dL mais elevados em crianças que tinham transtorno do hábito alimentar, independentemente da idade, presença de escória visível no peridomicílio, situação de emprego do pai, história familiar de intoxicação pelo chumbo e desnutrição. CONCLUSÕES: O passivo ambiental da fundição de chumbo, desativada em 1993, permanece como um fator de risco relevante para elevar os níveis desse metal no sangue de crianças, particularmente aquelas que apresentam transtornos do hábito alimentar.OBJECTIVE: To determine the blood lead levels in children living an inactive lead foundry in the city of Santo Amaro da Purificação,state of Bahia, in September of 1998; and to identify factors associated with differences in these levels. METHODS: Cross-sectional study with children between 1 and 4 years of age living within 1 km of the lead foundry. Mothers or guardians of 47 children answered a questionnaire concerning ingestion of clay, soli, plaster and / or other materias (pica,and other relevant epidemiological aspects. The concentration of lead in blood was determined by atermined by atomic absorption espectrophotometry. RESULTS: The mean lead level was 17

  3. East Capital suunab investorid Venemaale / Gert Tiivas ; interv. Raivo Sormunen

    Index Scriptorium Estoniae

    Tiivas, Gert, 1973-

    2007-01-01

    Rootsi investeerimispanga East Capitali Balti regiooni juht Gert Tiivas soovitab investeerida Baltimaadest suurema potentsiaaliga riikide börsidele. Vt. samas: CV: Gert Tiivas; East Capitali fondid. Diagramm: East Capitali Venemaa fondis on enim raha

  4. King Cove, Alaska Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  5. Arena Cove, California Coastal Digital Elevation Model

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — NOAA's National Geophysical Data Center (NGDC) is building high-resolution digital elevation models (DEMs) for select U.S. coastal regions. These integrated...

  6. MISR Views the Middle East

    Science.gov (United States)

    2000-01-01

    This image, generated using 16 orbits of MISR data collected between August 16 and August 30, 2000, takes us to the cradle of many civilizations. The data are from the 60-degree aftward-viewing camera. Because the individual orbit swaths are only 400 kilometers wide, they were 'mosaiced' together to form this composite picture, which covers about 2700 kilometers from west to east and 1750 kilometers from north to south. A few discontinuities are present in the mosaic, particularly near clouds, due to changes in the scene which occurred between dates when the individual orbit data were acquired.At the northern tip of the Red Sea, the Gulf of Suez and the Gulf of Aqaba frame the sandy deserts and spectacular mountains of the Sinai Peninsula. The highest peaks are Gebel Katherina (Mountain of St. Catherine, 2637 meters) and Gebel Musa (Mountain of Moses, also known as Mount Sinai, 2285 meters). To the northeast, Israel and Jordan flank the Dead Sea, one of the saltiest inland water bodies in the world. At its northern edge is Qumran, where the ancient Scrolls were discovered; the city of Jerusalem lies about 30 kilometers to the west.Several large rivers are prominent. Flowing southeastward through Iraq are the Tigris and Euphrates. The dark area between the two rivers, northwest of the Persian Gulf, is a very fertile region where fishing and farming are prevalent. Wending its way through eastern Egypt is the Nile. In the south is Lake Nasser and the Aswan Dam; continuing northward the Nile passes the Temple of Luxor as it sharply loops to the east. It then turns west and northward, eventually passing the capital city of Cairo, and finally spreading into a prominent delta as it empties into the Mediterranean Sea. The bright dot just west of the apex of the delta marks the location of the great Pyramids and Sphinx complexes on the Giza Plateau. On the coast, west of the delta, is the ancient city of Alexandria, Egypt's main seaport.'MISR', as it turns out, is the

  7. Networks model of the East Turkistan terrorism

    Science.gov (United States)

    Li, Ben-xian; Zhu, Jun-fang; Wang, Shun-guo

    2015-02-01

    The presence of the East Turkistan terrorist network in China can be traced back to the rebellions on the BAREN region in Xinjiang in April 1990. This article intends to research the East Turkistan networks in China and offer a panoramic view. The events, terrorists and their relationship are described using matrices. Then social network analysis is adopted to reveal the network type and the network structure characteristics. We also find the crucial terrorist leader. Ultimately, some results show that the East Turkistan network has big hub nodes and small shortest path, and that the network follows a pattern of small world network with hierarchical structure.

  8. A nuclear-weapon-free Middle East

    International Nuclear Information System (INIS)

    Jortner, Joshua

    1986-01-01

    The paper examines the issue of nuclear-weapon States involvement in regional conflicts, and whether such a conflict in the Middle East could trigger a nuclear war between the Super-Powers. Comments on the Middle Eastern situation are given, along with a discussion of the Non-Proliferation Treaty (NPT) and the Middle East, Israel and the NPT, and the nuclear potential in Arab countries. The proposal, by Israel, of a nuclear weapon-free zone in the Middle East is outlined. (UK)

  9. East Asian perspective on global environmental problems

    International Nuclear Information System (INIS)

    Yonehara, M.

    1995-01-01

    The Central Research Institute of Electric Power Industry has been conducting active global warming research programs focusing on development of a method to forecast climate change accompanying global warming both globally and in East Asia. A regional climate change forecasting method is being developed and researches are conducted on impacts of climate change on the natural and social environment in East Asia. Researches are also conducted focusing on the relationship between emissions and deposition of acid substances and assessment of the environmental impacts of acid rain in East Asia. 4 figs

  10. Turkmenistan and the Middle East

    Directory of Open Access Journals (Sweden)

    Michael B. Bishku

    2016-01-01

    Full Text Available Turkmenistan is a weak country militarily, but well-­endowed with natural gas reserves. While the latter also insulates it somewhat from international criticism of its human rights abuses, unfortunately, Turkmenistan is landlocked and dependent upon the goodwill of its neighbors in order to export that commodity. Additionally, Turkmenistan is in need of technological assistance. Given its relatively homogenous population and its hydrocarbon wealth it has adopted a policy of subsidizing certain necessities—though it underfunds other—and is fairly stable internally. Nevertheless, it is ruled under an autocratic political system, suffers massive corruption, and has to contend with fears of instability on its borders. Therefore, Turkmenistan has adopted a policy of permanent neutrality and is open to cooperation with all its neighbors as well as the big powers. The countries of the Middle East as both immediate and nearby neighbors play an important part in the international relations of Turkmenistan and in providing technological assistance and economic investments. This article, which reviews and analyzes those ties, utilizes government documents, academic works and newspapers from Turkmenistan and Middle Eastern countries.

  11. Middle East food safety perspectives.

    Science.gov (United States)

    Idriss, Atef W; El-Habbab, Mohammad S

    2014-08-01

    Food safety and quality assurance are increasingly a major issue with the globalisation of agricultural trade, on the one hand, and intensification of agriculture, on the other. Consumer protection has become a priority in policy-making amongst the large economies of the Middle East and North Africa (MENA) countries following a number of food safety incidents. To enhance food safety, it is necessary to establish markets underpinned by knowledge and resources, including analysis of international rejections of food products from MENA countries, international laboratory accreditation, improved reporting systems and traceability, continued development and validation of analytical methods, and more work on correlating sensory evaluation with analytical results. MENA countries should develop a national strategy for food safety based on a holistic approach that extends from farm-to-fork and involves all the relevant stakeholders. Accordingly, food safety should be a regional programme, raising awareness among policy- and decision-makers of the importance of food safety and quality for consumer protection, food trade and economic development. © 2014 Society of Chemical Industry.

  12. Unrealistic Optimism: East and West?

    Science.gov (United States)

    Joshi, Mary Sissons; Carter, Wakefield

    2013-01-01

    Following Weinstein’s (1980) pioneering work many studies established that people have an optimistic bias concerning future life events. At first, the bulk of research was conducted using populations in North America and Northern Europe, the optimistic bias was thought of as universal, and little attention was paid to cultural context. However, construing unrealistic optimism as a form of self-enhancement, some researchers noted that it was far less common in East Asian cultures. The current study extends enquiry to a different non-Western culture. Two hundred and eighty seven middle aged and middle income participants (200 in India, 87 in England) rated 11 positive and 11 negative events in terms of the chances of each event occurring in “their own life,” and the chances of each event occurring in the lives of “people like them.” Comparative optimism was shown for bad events, with Indian participants showing higher levels of optimism than English participants. The position regarding comparative optimism for good events was more complex. In India those of higher socioeconomic status (SES) were optimistic, while those of lower SES were on average pessimistic. Overall, English participants showed neither optimism nor pessimism for good events. The results, whose clinical relevance is discussed, suggest that the expression of unrealistic optimism is shaped by an interplay of culture and socioeconomic circumstance. PMID:23407689

  13. Unrealistic optimism: east and west?

    Directory of Open Access Journals (Sweden)

    Mary Sissons Joshi

    2013-02-01

    Full Text Available Following Weinstein’s pioneering work (1980 many studies established that people have an optimistic bias concerning future life events. At first, the bulk of research was conducted using populations in North America and Northern Europe, the optimistic bias was thought of as universal, and little attention was paid to cultural context. However, construing unrealistic optimism as a form of self-enhancement, some researchers noted that it was far less common in East Asian cultures. The current study extends enquiry to a different non-Western culture. Two hundred and eighty seven middle aged and middle-income participants (200 in India, 87 in England rated 11 positive and 11 negative events in terms of the chances of each event occurring in their own life, and the chances of each event occurring in the lives of people like them. Comparative optimism was shown for bad events, with Indian participants showing higher levels of optimism than English participants. The position regarding comparative optimism for good events was more complex. In India those of higher socioeconomic status were optimistic, while those of lower socioeconomic status were on average pessimistic. Overall, English participants showed neither optimism nor pessimism for good events. The results, whose clinical relevance is discussed, suggest that the expression of unrealistic optimism is moulded by an interplay of culture and socioeconomic circumstance.

  14. JPRS Report, Near East & South Asia

    National Research Council Canada - National Science Library

    1992-01-01

    This report covers international issues relating to the Near East: regional affairs, Palestinian affairs, Iraq, Jordan, Mauritania, Morocco, Sudan, United Arab Emirates, and the Republic of Yemen; and South Asia...

  15. Scopus: Journal of East African Ornithology: Contact

    African Journals Online (AJOL)

    Principal Contact. Darcy Ogada Dr Bird Committee of the East Africa Natural History Society. Editors,. Scopus,. c/o Nature Kenya,. P.O. Box 44486,. G.P.O. 00100,. Nairobi, Kenya. Email: scopus@naturekenya.org ...

  16. East African Journal of Sciences: Submissions

    African Journals Online (AJOL)

    Aims The East African Journal of Sciences (EAJS) publishes original scientific ... of ideas among scientists engaged in research and development activities; and ... font size 12, Times New Roman), including tables, figures and illustrations.

  17. Near East/South Asia Report

    National Research Council Canada - National Science Library

    1986-01-01

    .... This report from the Near East/South Asia, Egypt, Libya, Tunisa, Iraq, Israel, Kuwait, Oman, Saudi Arabia, Syria, United Arab Emirates, Iran and Pakistan, the articles are on Politics, Economics...

  18. Zoning, 2004, East Baton Rouge Parish, Louisiana

    Data.gov (United States)

    Louisiana Geographic Information Center — This is a graphical polygon dataset depicting the zoning boundaries of the East Baton Rouge Parish of the State of Louisiana. Zoning can be defined as the range of...

  19. Scientific Communication | Okolo | East African Medical Journal

    African Journals Online (AJOL)

    East African Medical Journal. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 92, No 2 (2015) >. Log in or Register to get access to full text downloads.

  20. Biogas - Bioenergy potential in East Africa

    International Nuclear Information System (INIS)

    1997-01-01

    The workshop is part of the project: 'Energy production from Sisal Waste in East Africa' sponsored by the Danish Energy Agency, an agency under the Danish Ministry of Environment and Energy. This project has been carried out in close cooperation between the Danish Technological Institute and University of Dar es Salaam, Applied Microbiology Unit, who has also taken care of the practical arrangement. The main objectives of the workshop was: To present the ongoing research in East Africa on biogas production from organic residues; To get an overview of political and administrative issues related to promotion and implementation of renewable energy facilities in East Africa; To discuss appropriate set-ups for bioenergy facilities in East Africa. (au)

  1. Biogas - Bioenergy potential in East Africa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    The workshop is part of the project: `Energy production from Sisal Waste in East Africa` sponsored by the Danish Energy Agency, an agency under the Danish Ministry of Environment and Energy. This project has been carried out in close cooperation between the Danish Technological Institute and University of Dar es Salaam, Applied Microbiology Unit, who has also taken care of the practical arrangement. The main objectives of the workshop was: To present the ongoing research in East Africa on biogas production from organic residues; To get an overview of political and administrative issues related to promotion and implementation of renewable energy facilities in East Africa; To discuss appropriate set-ups for bioenergy facilities in East Africa. (au)

  2. Biogas - Bioenergy potential in East Africa

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    The workshop is part of the project: `Energy production from Sisal Waste in East Africa` sponsored by the Danish Energy Agency, an agency under the Danish Ministry of Environment and Energy. This project has been carried out in close cooperation between the Danish Technological Institute and University of Dar es Salaam, Applied Microbiology Unit, who has also taken care of the practical arrangement. The main objectives of the workshop was: To present the ongoing research in East Africa on biogas production from organic residues; To get an overview of political and administrative issues related to promotion and implementation of renewable energy facilities in East Africa; To discuss appropriate set-ups for bioenergy facilities in East Africa. (au)

  3. Hydrography, 2004, East Baton Rouge Parish, Louisiana

    Data.gov (United States)

    Louisiana Geographic Information Center — The Hydrography layer is an area geometry depicting the various water features that include the rivers, streams, creeks, lakes, etc of East Baton Rouge Parish.

  4. The Water Conflict in the Middle East

    National Research Council Canada - National Science Library

    1997-01-01

    The water conflict in the Middle East is reaching a crisis peak. The region suffers from a shortage of water, a high rate of population growth and the absence of a clear criteria for sharing waters within the region...

  5. Near East/South Asia Report

    National Research Council Canada - National Science Library

    1986-01-01

    .... This report from the Near East/South Asia, Algeria, Egypt, Sudan, Tunisia, Israel, Lebanon, Afghanistan, Bangladesh, Iran and Pakistan, contains articles on Politics, Economics, Regional Affairs and Military Affairs...

  6. EAST OJAI HYDROLOGY, VENTURA COUNTY, USA

    Data.gov (United States)

    Federal Emergency Management Agency, Department of Homeland Security — The basis of the hydrologic data for East Ojai FIS is the HSPF study for Ventura River watershed documented in a report entitled...

  7. East African Agricultural and Forestry Journal

    African Journals Online (AJOL)

    East African Agricultural and Forestry Journal is published by the Kenya ... water resource base to meet the challenges of poverty alleviation and food security. ... on maize growth, nitrogen uptake and yield in a semi-arid Kenyan environment ...

  8. Microbial keratitis in West and East Malaysia

    OpenAIRE

    Vanitha Ratnalingam; Thiageswari Umapathy; Kala Sumugam; Hanida Hanafi; Shamala Retnasabapathy

    2017-01-01

    AIM: To evaluate the epidemiological and etiological factors of microbial keratitis seen in tertiary hospitals in West and East Malaysia.METHODS: A total of 207 patients were enrolled. Patients referred for microbial keratitis to Sungai Buloh Hospital and Kuala Lumpur Hospital in West Malaysia and Queen Elizabeth Hospital and Kuching General Hospital in East Malaysia were recruited. Risk factors were documented. Corneal scrapings for microscopy and culture were performed.RESULTS: The most com...

  9. Regional Integration: A Political Federation of the East African ...

    African Journals Online (AJOL)

    The aim of this paper is to explore the possibility and viability of an East African political federation project. Since the late 1800s under the then British East Africa, the countries of East Africa have been searching for ways to integrate. The search led to the establishment of the East African Community (EAC) in December ...

  10. The East African rift system

    Science.gov (United States)

    Chorowicz, Jean

    2005-10-01

    This overview paper considers the East African rift system (EARS) as an intra-continental ridge system, comprising an axial rift. It describes the structural organization in three branches, the overall morphology, lithospheric cross-sections, the morphotectonics, the main tectonic features—with emphasis on the tension fractures—and volcanism in its relationships with the tectonics. The most characteristic features in the EARS are narrow elongate zones of thinned continental lithosphere related to asthenospheric intrusions in the upper mantle. This hidden part of the rift structure is expressed on the surface by thermal uplift of the rift shoulders. The graben valleys and basins are organized over a major failure in the lithospheric mantle, and in the crust comprise a major border fault, linked in depth to a low angle detachment fault, inducing asymmetric roll-over pattern, eventually accompanied by smaller normal faulting and tilted blocks. Considering the kinematics, divergent movements caused the continent to split along lines of preexisting lithospheric weaknesses marked by ancient tectonic patterns that focus the extensional strain. The hypothesis favored here is SE-ward relative divergent drifting of a not yet well individualized Somalian plate, a model in agreement with the existence of NW-striking transform and transfer zones. The East African rift system comprises a unique succession of graben basins linked and segmented by intracontinental transform, transfer and accommodation zones. In an attempt to make a point on the rift system evolution through time and space, it is clear that the role of plume impacts is determinant. The main phenomenon is formation of domes related to plume effect, weakening the lithosphere and, long after, failure inducing focused upper mantle thinning, asthenospheric intrusion and related thermal uplift of shoulders. The plume that had formed first at around 30 Ma was not in the Afar but likely in Lake Tana region (Ethiopia

  11. Pathways to an East Asian Higher Education Area: A Comparative Analysis of East Asian and European Regionalization Processes

    Science.gov (United States)

    Chao, Roger Y., Jr.

    2014-01-01

    The Author argues that historical regional developments in Europe and East Asia greatly influence the formation of an East Asian Higher Education Area. As such, this article compares European and East Asian regionalization and higher education regionalization processes to show this path dependency in East Asian regionalization of higher education…

  12. 78 FR 20559 - Safety Zones; Swim Events in the Captain of the Port New York Zone; Hudson River, East River...

    Science.gov (United States)

    2013-04-05

    ... Liberty to Freedom Swim: Waters of the Upper New York Bay, from Liberty Island, NJ to North Cove, New York... security of people, places or vessels. 7. Unfunded Mandates Reform Act The Unfunded Mandates Reform Act of..., local, or tribal government, in the aggregate, or by the private sector of $100,000,000 (adjusted for...

  13. The great East Japan earthquake

    Energy Technology Data Exchange (ETDEWEB)

    Fluke, R.

    2011-06-15

    'Full text:' More formally called the Tohoku-Chihou-Taiheiyo-Oki Earthquake of March 11, 2011, it was the ensuing tsunami that caused the most death and destruction to the north-east coastal region of Japan. It is also what caused the multiple meltdowns at Fukushima Dai-ichi. Reactor Unit 1, ironically, was scheduled to be permanently shut down for decommissioning just two weeks later. The Fukushima Dai-ichi nuclear power plant has a tsunami protection barrier designed for the worst recorded tsunami in that area since 1896 - to a height of 5.7 m. The plant itself is on an elevated grade of about 10 m. The tsunami, reported to be 14-15 m, caused inundation of the entire site with at least four metres of seawater. The seawater flooded the turbine building and damaged electrical equipment including the emergency diesel generators, leaving the entire six-unit nuclear power plan without any source of AC power, known as the 'station blackout scenario'. There are numerous reports available on-line at various sites. The Japanese Government report is frank and forthcoming on the causes and the lessons learned, and the lAEA Mission report is in-depth and well presented, not only as a factual account of the events but as a unified source of the conclusions and lessons learned. Photos of the catastrophe are available at the TEPCO web site: http://www.tepco.co.jp/en/index-e.html. In this edition of the Bulletin there is a 'layman's' description of CANDU and BWR design in terms of the fundamental safety principles - Control, Cool and Contain as well as a description of how these principles were met, or not met at Fukushima Dai-ichi. Also, an excerpt from the IAEA Expert Mission is included. We 'technocrats' sometimes forget about the human aspects of a nuclear disaster. An essay by Dr. Michael Edwards is included entitled 'Psychology, Philosophy and Nuclear Science'. Other references to the events appear throughout this

  14. The great East Japan earthquake

    International Nuclear Information System (INIS)

    Fluke, R.

    2011-01-01

    'Full text:' More formally called the Tohoku-Chihou-Taiheiyo-Oki Earthquake of March 11, 2011, it was the ensuing tsunami that caused the most death and destruction to the north-east coastal region of Japan. It is also what caused the multiple meltdowns at Fukushima Dai-ichi. Reactor Unit 1, ironically, was scheduled to be permanently shut down for decommissioning just two weeks later. The Fukushima Dai-ichi nuclear power plant has a tsunami protection barrier designed for the worst recorded tsunami in that area since 1896 - to a height of 5.7 m. The plant itself is on an elevated grade of about 10 m. The tsunami, reported to be 14-15 m, caused inundation of the entire site with at least four metres of seawater. The seawater flooded the turbine building and damaged electrical equipment including the emergency diesel generators, leaving the entire six-unit nuclear power plan without any source of AC power, known as the 'station blackout scenario'. There are numerous reports available on-line at various sites. The Japanese Government report is frank and forthcoming on the causes and the lessons learned, and the lAEA Mission report is in-depth and well presented, not only as a factual account of the events but as a unified source of the conclusions and lessons learned. Photos of the catastrophe are available at the TEPCO web site: http://www.tepco.co.jp/en/index-e.html. In this edition of the Bulletin there is a 'layman's' description of CANDU and BWR design in terms of the fundamental safety principles - Control, Cool and Contain as well as a description of how these principles were met, or not met at Fukushima Dai-ichi. Also, an excerpt from the IAEA Expert Mission is included. We 'technocrats' sometimes forget about the human aspects of a nuclear disaster. An essay by Dr. Michael Edwards is included entitled 'Psychology, Philosophy and Nuclear Science'. Other references to the events appear throughout this edition.(author)

  15. The genus Cuscuta L. in East Asia

    Directory of Open Access Journals (Sweden)

    E. V. Aistova

    2015-07-01

    Full Text Available On the basis of published data, herbarium collections  and  our  own  research  the  overview  of  the spread  of  7  dodder  species  (genus  Cuscuta  on  the territory of  of the Russian Far East and East Asia is given. The  history  of  research  dodders  on  the  territory  of  the Russian Far East, ecological and spreading peculiarities are described. Certain eurytopic species (C. campestris Yunck., C. japonica Choisy and C. europaea L. growing on the territory of the Russian Far East have plasticity and  rapid  adaptive  response  for  changing  ecological and  geographical  conditions.  C.  epilinum  Weihe, C. epithymum (L. Nathh., C. tinei Insenga have not been naturalized in the Russian Far East.

  16. Forecasting of Currency Crises in East Asia

    Directory of Open Access Journals (Sweden)

    Chi-Young Song

    2005-06-01

    Full Text Available In this paper, we have developed a forecasting system for currency crisis in East Asia based on a signaling approach. Our system uses 15 monthly indicators of five East Asian countries including Indonesia, Korea, Malaysia, the Philippines and Thailand that were severely hit by the currency crisis in 1997. We investigate the performance of the system through deploying out-of-sample forecasting for the periods both before and after the 1997 East Asian currency crisis. Unlike the existing research based on the signaling approach, our out-of-sample forecasting does not fix the in-sample period. The out-of-sample forecasting between July 1995 and June 1997 shows that prior to breakout of the crisis, several indicators including real exchange rates and exports sent frequent warnings to all crisis-hit East Asian countries except the Philippines. This may indicate that a signaling-based early warning system for currency crisis could have been an useful method of forecasting the East Asian crisis. On the other hand, we also find that our forecasting system often generates warning signals during the out-of-sample period between July 1999 and June 2001. Since we have not observed any currency crisis in this region after 1998, these are all false alarms, indicating that our system may be seriously exposed to the type II error. We can, however, mitigate this problem if we adjust the optimal critical values of indicators depending on the preferences of forecasting system manager.

  17. EAST ICRF system for long pulse operation

    International Nuclear Information System (INIS)

    Zhao, Y.P.; Zhang, X.J.; Mao, Y.Z.

    2013-01-01

    Radio frequency (RF) power in the ion cyclotron range of frequencies (ICRF) is one of the primary auxiliary heating techniques for Experimental Advanced Superconducting Tokamak (EAST). A 6.0 MW ICRF systems in the range of 25-70 MHz has been put into operation during the EAST 2012 spring campaign. The ICRF systems consist of two port-mounted antennas and each antenna is driven by two independent 1.5 MW RF power source. Another four 1.5 MW ICRF system is under way of construction.The system will deliver more than 10 MW of RF power to the plasma for 1000 sec pulse length. This paper gives brief introduction of the ICRF systems capability on EAST. (author)

  18. Recent progress with ICRF heating on EAST

    International Nuclear Information System (INIS)

    Zhang Xinjun; Zhao, Y.P.; Mao, Y.Z.

    2014-01-01

    Radio Frequency (RF) power in the ion cyclotron range of frequencies (ICRF) is one of the primary auxiliary heating techniques for Experimental Advanced Superconducting Tokamak (EAST). The ICRF system for the EAST has been developed to support long-pulse, high-β, advanced tokamak fusion physics experiments. The ICRF system can deliver 12 MW of RF power to the plasma for 1000 seconds through two antennas located in B- and I-ports. Each ICRF transmitter with high power up to 1.5 MW has been successfully tested on a dummy load. The main technical features of the ICRF system is described. Two simulation codes, TORIC (a full wave solver) and SSFPQL (the quasilinear Fokker-Planck solver), are combined to simulate the ICRF heating in the EAST 2D magnetic configuration. The fast wave propagation and absorption characteristics, power partitions among the plasma species and the RF driven energetic tails have been analyzed. (author)

  19. Soviet and East European energy databook

    International Nuclear Information System (INIS)

    Wilson, D.C.

    1991-01-01

    For the USSR, energy data is assembled under the following main headings: energy and the economy; production; engineering; exploration; transport of fuel; refining; consumption by sector; employment; finance; trade; electricity. There are 162 tables. Five tables of data on Eastern Europe as a region cover production of energy, consumption, and exports of crude and oil products. Using similar broad headings as these for the USSR, a further 184 tables give data for the following individual countries: Bulgaria; Czechoslovakia; East Germany; Hungary; Poland; Romania; Yugoslavia. The data has been accumulated from Soviet and East European sources, mainly newspapers, journals, annual yearbooks and private contacts and the chief of these are listed. (UK)

  20. The Middle East, OPEC and oil

    International Nuclear Information System (INIS)

    Roberts, J.

    1996-01-01

    The importance of the Middle East to the oil industry, was discussed. The unresolved Arab-Israeli dispute and the ongoing conflicts in the Gulf are the two main reasons for political instability in the Middle East. This in turn, shapes the security of the region and its oil supplies. The factors which will shape the future of OPEC, including the Arab-Israeli conflict, the issue of the return of Iraqi crude to the market, and production decisions by Saudi Arabia were discussed in the context of their impact on OPEC's role as a coordinator of oil policies and of market stabilisation through price control

  1. Development of plasma fueling on EAST

    International Nuclear Information System (INIS)

    Yao, X.J.; Zheng, X.W.; Li, C.Z.; Chen, Y.

    2015-01-01

    To achieve better plasma density control, experimental advanced superconducting tokamak (EAST) has already equipped with gas puffing (GP), supersonic molecular beam injection (SMBI) and pellet injection (PI). During the past few years, lots of experiments and ameliorations have been done. The performance of the SMBI and gas puffing (GP) feedback systems were used and compared. And the preliminary result of pellet injection was also presented here. The results shows the PI and SMBI were more compatible to the long pulse high density discharge on EAST. (author)

  2. African Muslim Youth and the Middle East

    DEFF Research Database (Denmark)

    Ihle, Annette Haaber

    this African tradition of religious scholarship in the Middle East. The paper will, with the help of Pierre Bourdieu's notion of forms of capital related to various fields, analyse the challenges which Muslim students encounter during their stay in the Middle East and the forms of capital they bring back......, marked by economic decline and political instability. In Africa a weak or even failed state often means that young people have in reality no access to political, educational or economic positions and resources. In some countries like Nigeria, Ghana and the Ivory Coast the marginalisation of the youth...

  3. 78 FR 26359 - Community of Elfin Cove, DBA Elfin Cove Utility Commission; Notice of Preliminary Permit...

    Science.gov (United States)

    2013-05-06

    ...-kilowatt (kW) power recovery turbine; (4) a 25-foot-long, 8-foot- wide, 3-foot-deep cobble-lined tailrace... 150-foot-long, 8- foot-wide, 3-foot-deep cobble-lined tailrace discharging flows into Port Althorp... electronically via the Internet. See 18 CFR 385.2001(a)(1)(iii) and the instructions on the Commission's Web site...

  4. Disruption simulation for the EAST plasma

    International Nuclear Information System (INIS)

    Niu Xingping; Wu Bin

    2007-01-01

    The disruptions due to vertical displacement event for the EAST plasma are simulated in this article by using the TSC program. Meanwhile, the evolutions of the halo current and stress on vacuum vessel are calculated; the disruptions at different initial conditions are compared with each other, and killer pellet injection is simulated for the device fast shutting-down. (authors)

  5. Ice age plant refugia in East Greenland

    DEFF Research Database (Denmark)

    Funder, Svend Visby

    1979-01-01

    From the distribution of plants it has been inferred by some botanists that ice-free areas existed in East Greenland accommodating a flora which survived one or several ice ages in the area. Comparing this evidence with recent information on the chronology of glaciations and post-glacial vegetation...

  6. Educational Transition of East Malaysian Distance Learners.

    Science.gov (United States)

    Saw, K. G.; Awang, M. N.; Idrus, R. M.; Atan, H.; Azli, N. A.; Jaafar, I.; Rahman, Z. A.; Latiff, Z. A.

    1999-01-01

    Describes results of a study of the changing perceptions of East Malaysian distance learners studying at the Universiti Sains Malaysia. Highlights include students' perceptions of their study skills; and the impact of their studies on other areas of their life, including social obligations, recreation, families, health, finances, work, and…

  7. Journal of East African Natural History: Submissions

    African Journals Online (AJOL)

    2017-11-01

    Nov 1, 2017 ... Author Guidelines. Submission: manuscripts should be submitted as a Word document in an email attachment, to the Editor-in-Chief, Journal of East African Natural History at office@naturekenya.org. The manuscript should be accompanied by a covering letter from the author, or in the case of multiple ...

  8. Correlation Dynamics in East Asian Financial Markets

    NARCIS (Netherlands)

    Kuper, Gerard; Lestano, L

    2014-01-01

    This paper examines the dynamic relationship between stock returns and exchange rate changes using daily data from January 3, 1994 - September 27, 2013 for six East Asian countries: Indonesia, Malaysia, the Philippines, Singapore, South Korea and Thailand. We estimate conditional correlations using

  9. "Reading to Write" in East Asian Studies

    Science.gov (United States)

    Freedman, Leora

    2013-01-01

    A reading-writing initiative began in 2011-12 at the University of Toronto as a partnership between an East Asian Studies (EAS) department and an English Language Learning (ELL) Program. In this institution, students are expected to enter into scholarly discussions in their first year essays, yet many (both native English speakers and non-native…

  10. Financing Technological Upgrading in East Asia

    NARCIS (Netherlands)

    Rasiah, Rajah; Mubarik, Shujaat; Yap, Xiao-Shan

    2017-01-01

    There has been considerable discussion on the drivers of economic growth in East Asia. While most studies recognize that capital accumulation and macroeconomic management were critical in hastening growth, few have examined systematically and comparatively how policy frameworks – spearheaded through

  11. Correlation dynamics in East Asian financial markets

    NARCIS (Netherlands)

    Lestano, L; Kuper, Gerard H.

    2016-01-01

    We examine the dynamic relationship between stock returns and exchange rate changes using daily data from January 1994 to September 2013 for six East Asian countries. We use the multivariate GARCH-DCC model in order to disclose the relationship between stock markets and foreign exchange markets

  12. Five bid to host Middle East synchroton

    CERN Multimedia

    McCabe, H

    1999-01-01

    Germany is willing to donate a synchrotron to a research centre to be built somewhere in the Middle East. Bids to host the centre were submitted by Turkey, Cyprus, Iran, the Palestinian Authority and Egypt. Funding of at least 30 million US dollars still needs to be found (1 page).

  13. Ethnic entrepreneurship and internationalisation in East Africa

    NARCIS (Netherlands)

    Leendert de Bell; Hein Roelfsema; Khalidi Swabiri

    Using the World Bank Enterprise Surveys panel data for the East African Community, this paper analyses the influence of ethnic origin of entrepreneurs on internationalisation and firm performance. Using traditional probit and OLS estimation techniques in combination with matching strategies to

  14. Transmission of Middle East respiratory syndrome coronavirus ...

    African Journals Online (AJOL)

    ... hand hygiene, and cough etiquette, would minimize the infection rate among HCPs. The required consumables for maintaining hand hygiene should be readily available to all HCPs. Keywords: Middle East respiratory syndrome coronavirus (MERS-CoV), Systematic review, healthcareassociated infections, Coronaviruses ...

  15. Methane from the East Siberian Arctic shelf

    DEFF Research Database (Denmark)

    Petrenko...[], Vasilii V.; Etheridge, David M.

    2010-01-01

    In their Report “Extensive methane venting to the atmosphere from sediments of the East Siberian Arctic Shelf” (5 March, p. 1246), N. Shakhova et al. write that methane (CH4) release resulting from thawing Arctic permafrost “is a likely positive feedback to climate warming.” They add...

  16. Financing environmental policy in East Central Europe

    NARCIS (Netherlands)

    Kolk, A.; van der Weij, E.

    1998-01-01

    The transition in East Central Europe created a general optimism which was reflected in a belief that a solution to the environmental problems faced by these countries would be found. There were great expectations regarding the blessings of the market economy, which would diminish state-guided waste

  17. Consented Autopsy and the Middle-East.

    Science.gov (United States)

    Kharoshah, Magdy A; Hussain, Syed Ather; Madadin, Mohammed; Menezes, Ritesh G

    2017-02-01

    Consented autopsy is almost non-existent in the Middle-East where established social and cultural beliefs regarding the procedure might discourage family members from requesting a consented autopsy. Evidence suggests that new information is obtained from consented autopsies. It would not be in the best interest of medicine if social and cultural misconceptions succeed in erasing the existence of consented autopsies entirely.

  18. People and forests in East Kalimantan

    Science.gov (United States)

    Kuswata Kartawinata; Timothy C. Jessup; A. P. Vayda; S. Riswan; Cynthia Mackie; Nancy E. Peluso

    1992-01-01

    Two major Indonesian-MAB (Man and the Biosphere) projects were carried out in the province of East Kalimantan, Indonesia, in the 1980s. Investigators found that farmers vary in their reason for practicing shifting cultivation of logging and agriculture, in their intensity of farming, and in the amount of damage they caused forests in their practices. Shifting...

  19. East Africa’s Fragmented Security Cooperation

    DEFF Research Database (Denmark)

    Nordby, Johannes Riber; Jacobsen, Katja

    2013-01-01

    Since the 1990s, East Africa has developed what appears to be an impressive security architecture. Katja Lindskov Jacobsen and Johannes Riber Nordby warn, however, that appearances can be deceptive. The region’s security institutions remain too nationalistic and self-interested for their own good....

  20. East African Journal of Sciences: Editorial Policies

    African Journals Online (AJOL)

    Open Access Policy. This journal provides immediate open access to its content, upon registration, on the principle that making research freely available to the public supports a greater global exchange of knowledge. Creative Commons License East African Journal of Sciences by Haramaya University is licensed under a ...

  1. Housing East Asia: socioeconomic and demographic challenges

    NARCIS (Netherlands)

    Doling, J.; Ronald, R.

    2014-01-01

    Housing and home ownership has been strongly embedded in East Asian socioeconomic and policy models. Based on the primacy of national economic growth objectives, it was promoted as a means of, on the one hand, contributing directly to economic growth through the motor of the construction industry,

  2. National oil companies of South East Asia

    International Nuclear Information System (INIS)

    Singh, Gurdip

    1998-12-01

    Contains Executive Summary and Chapters on: Pertamina; Petronas; Petroleum Authority of Thailand; Philippines National Oil Company; Petro Vietnam; Myanmar Oil and Gas Enterprise; Singapore; Asean Free Trade Agreement, and Appendix on Petroleum tax legislation in the main south east Asian countries. (Author)

  3. East African Journal of Public Health

    African Journals Online (AJOL)

    The East African Journal of Public Health is a multi-disciplinary journal publishing scientific research work from a range of public health related disciplines including community medicine, epidemiology, nutrition, behavioural sciences, health promotion, health education, communicable and non-communicable disease.

  4. Assessing sanitary mixtures in East African cities

    NARCIS (Netherlands)

    Letema, S.C.

    2012-01-01

    The urbanisation of poverty and informality in East African cities poses a threat to environmental
    health, perpetuates social exclusion and inequalities, and creates service gaps (UN-Habitat, 2008).
    This makes conventional sanitation provision untenable citywide, giving rise to the

  5. Central control system for the EAST tokamak

    International Nuclear Information System (INIS)

    Sun Xiaoyang; Ji Zhenshan; Wu Yicun; Luo Jiarong

    2008-01-01

    The architecture, the main function and the design scheme of the central control system and the collaboration system of EAST tokamak are described. The main functions of the central control system are to supply a union control interface for all the control, diagnoses, and data acquisition (DAQ) subsystem and it is also designed to synchronize all those subsystem. (authors)

  6. Peculiarities of transformation processes in East Germany

    Directory of Open Access Journals (Sweden)

    Marion Dathe

    2011-03-01

    Full Text Available The process of socio-economic transformation of East German lands after the German reunification in 1990 is analyzed, the term "transformation" in frames of planned and market economies is defined. The author studies the historical determinants of the transformation process in Germany. German economic and industrial history in context of the driving forces and their social values, as well as the properties of the planning and economic systems that underlie the transformation of East German mentality, are considered. Further analysis is connected with economic, social and political components of the East German transformation process, "the dominance of the West", the collapse of the Council for Mutual Economic Assistance, privatization etc. Finally, the outcome of already traversed path of transformation of East Germany is considered. It is concluded, that the transformation process is not only historically conditioned situations of both the merging parties in the case of Germany, but also the positive or negative perception of its results and the motivation for its further implementation.

  7. East Midlands healthcare and bioscience sector strategy

    OpenAIRE

    East Midlands Development Agency

    2007-01-01

    The healthcare and bioscience sector is one of four priority sectors identified in the regional economic strategy, A Flourishing Region. This document sets out a strategy for maximising the contribution of the healthcare and biosciences sector to the economic development of the East Midlands.

  8. The Eichmann Trial on East German Television

    NARCIS (Netherlands)

    Keilbach, Judith

    2014-01-01

    abstractThe trial against Adolf Eichmann was one of the first transnational media events on television. Its world-wide coverage required transnational cooperation. Using East German television reports about the trial this article argues that although the event transcended national borders it

  9. The Eichmann Trial on East German Television

    Directory of Open Access Journals (Sweden)

    Judith Keilbach

    2014-06-01

    Full Text Available The trial against Adolf Eichmann was one of the first transnational media events on television. Its world-wide coverage required transnational cooperation. Using East German television reports about the trial this article argues that although the event transcended national borders it maintained at the same time ideological boundaries.

  10. Sponges from Clipperton Island, East Pacific

    NARCIS (Netherlands)

    van Soest, R.W.M.; Kaiser, K.L.; van Syoc, R.

    2011-01-01

    Twenty sponge species (totalling 190 individuals) were collected during the 1938, 1994 and 2004/5 expeditions to the remote island of Clipperton in the East Pacific Ocean. Seven species are widespread Indo-Pacific sponges; nine species comprise sponges new to science; four species were represented

  11. Soldiers and Civilians in Contemporary Middle East

    DEFF Research Database (Denmark)

    2017-01-01

    Despite the fact that the co-called Arab Spring has spread promising winds across the Middle East and the Northern Afria (MENA) region over the past decade, several countries in the region have nevertheless been caught up in devastating and destructive intra-state conflicts. A prevailing trend...

  12. Progress of the EAST project in China

    International Nuclear Information System (INIS)

    Wan, Y.X.; Wu, S.T.; Weng, P.D.; Li, J.G.; Gao, D.M.

    2005-01-01

    The Experimental Advanced Superconducting Tokamak (EAST) project is one of the National Mega-Projects of Science Research of China, which was approved by Chinese government in 1998. EAST is a full superconducting tokamak with an elongated plasma cross-section. The mission of the project is to widely investigate both of the physics and the technologies of advanced tokamak operations, especially the mechanism of power and particle handling for steady-state operations. The basic requirements for the EAST tokamak are full superconducting coils, suitable inductive current system, continuous working non-inductive current driven and heating systems, flexible operation scenarios, flexible J(r) and P(r) control, reliable and fast plasma positioning and shaping control, changeable plasma facing components, advanced divertor and diagnostics. Significant progress of the EAST project has been achieved during last two years. The R and D programs, mainly focused on the superconducting magnets, have processed successfully. The prototypes of main parts have been fabricated and qualified. Most of the key parts of the machine have been delivered to the assembly site. The assembly of the device has begun. It is planned to obtain the first plasma in 2005. The detail information of the testing results of superconducting magnets will be given in this paper. The assembly plan and the experimental plan will be introduced, too. (author)

  13. East African Journal of Public Health: Journal Sponsorship

    African Journals Online (AJOL)

    East African Journal of Public Health: Journal Sponsorship. Journal Home > About the Journal > East African Journal of Public Health: Journal Sponsorship. Log in or Register to get access to full text downloads.

  14. Scopus: Journal of East African Ornithology: Journal Sponsorship

    African Journals Online (AJOL)

    Scopus: Journal of East African Ornithology: Journal Sponsorship. Journal Home > About the Journal > Scopus: Journal of East African Ornithology: Journal Sponsorship. Log in or Register to get access to full text downloads.

  15. East and Central African Journal of Surgery: About this journal

    African Journals Online (AJOL)

    East and Central African Journal of Surgery: About this journal. Journal Home > East and Central African Journal of Surgery: About this journal. Log in or Register to get access to full text downloads.

  16. Archives: East and Central African Journal of Surgery

    African Journals Online (AJOL)

    Items 1 - 40 of 40 ... Archives: East and Central African Journal of Surgery. Journal Home > Archives: East and Central African Journal of Surgery. Log in or Register to get access to full text downloads.

  17. Detection of phylogenetic extraction of sheep populations in East ...

    African Journals Online (AJOL)

    USER

    2010-06-28

    Jun 28, 2010 ... populations in East and South Asia based on fuzzy ... Based on the previous research, according to the Hierarchy clustering, the sheep populations in East and South ... have been known and some data have been obtained,.

  18. ISSN 2073 ISSN 2073 9990 East Cent. Afr. J. 9990 East Cent. Afr. J ...

    African Journals Online (AJOL)

    Hp 630 Dual Core

    COSECSA/ASEA Publication East and Central African ... the one hand on medical technology and equipment and on the other hand on the medical .... traumatic brain injury was the main cause of death amongst emergency admissions at the.

  19. ISSN 2073 ISSN 2073 9990 East Cent. Afr. J. s 9990 East Cent. Afr.

    African Journals Online (AJOL)

    Hp 630 Dual Core

    she went abroad to South East Asia to seek better medical care. ... developed deep venous thrombosis and pulmonary thrombo embolism eventually ... lengthy procedures, change in nursing staff during procedures and failure to count surgical ...

  20. Technical diagnosis system for EAST tokamak

    International Nuclear Information System (INIS)

    Qian Jing; Weng, P.D.; Luo, J.R.; Chen, Z.M.; Wu, Y.

    2010-01-01

    Technical diagnosis system (TDS) is one of the important subsystems of EAST (experimental advanced superconducting tokamak) device, main function of which is to monitor status parameters in EAST device. Those status parameters include temperature of different positions of main components, resistance of each superconducting (SC) coils, joint resistance of SC coils and high-temperature superconducting (HTS) current leads, strain of cold-quality components endured force, and displacement and current of toroidal field (TF) coils in EAST device, which are analog input signals. In addition there are still some analog and digital output signals. The TDS monitors all of those signals in the period of EAST experiments. TDS data monitoring is described in detail for it plays important role during EAST campaign. And how to protect the SC magnet system during each plasma discharging is presented with data of temperature of coolant inlet and outlet of SC coils and feeders and cases of the TF coils and temperature in the upper and middle and bottom of the TF coil case. During construction of the TDS primary difficulties come from installation of Lakeshore Cernox temperature sensors, strain measurement of central solenoid coils support legs and installation of co-wound voltage sensors for quench detection. While during operation since the first commissioning big challenges are from temperature measurement changes in current leads and quench detection of PF coils. Those difficulties in both stages are introduced which are key to make the TDS reliable. Meanwhile analysis of experimental data like temperature as a back up to testify quench occurrence and stress on vacuum vessel thermal shield and vacuum vessel have also been discussed.

  1. Integration and reintegration in CARIM-East countries

    OpenAIRE

    STRATAN, Alexandru; SAVELYEVA, Galina; KOTELNIK, Vera; ZAKHAROVA, Svetlana

    2013-01-01

    CARIM-East: Creating an Observatory of Migration East of Europe Version in other language: Migration Policy Centre CARIM-East Research Report 2013/38 Policy in the field of migrants’ integration is a relatively new task for practically all CARIM-East countries. Integration has an impact upon demography, including the composition and structure of the country’s population, namely gender ratio, mortality, marriage structure, birth rate, ageing etc. While integrating into society migr...

  2. East Asian Values Surveys : making a case for East Asian-origin values survey concepts

    OpenAIRE

    Vinken, Henk

    2006-01-01

    This paper aims to contribute to social scientific work towards enhancing the cultural fit of comparative values surveys projects on a conceptual level both for Western and East Asian survey research communities and their publics. It starts with noting that, after a long period in which Western values were regarded superior ('orientalism'), in recent decades certain East Asian and specifically Confucian values are much celebrated ('reversed orientalism'). Yet, most contemporary cross-cultural...

  3. Impact of anthropogenic aerosols from global, East Asian, and non-East Asian sources on East Asian summer monsoon system

    Science.gov (United States)

    Wang, Qiuyan; Wang, Zhili; Zhang, Hua

    2017-01-01

    The impact of the total effects due to anthropogenic aerosols from global, East Asian, and non-East Asian sources on East Asian summer monsoon (EASM) system is studied using an aerosol-climate online model BCC_AGCM2.0.1_CUACE/Aero. The results show that the summer mean net all-sky shortwave fluxes averaged over East Asian monsoon region (EAMR) at the top of the atmosphere (TOA) and surface reduce by 4.8 and 5.0 W m- 2, respectively, due to the increases of global aerosol emissions in 2000 relative to 1850. Changes in radiations and their resulting changes in heat and water transport and cloud fraction contribute together to the surface cooling over EAMR in summer. The increases in global anthropogenic aerosols lead to a decrease of 2.1 K in summer mean surface temperature and an increase of 0.4 hPa in summer mean surface pressure averaged over EAMR, respectively. It is shown that the changes in surface temperature and pressure are significantly larger over land than ocean, thus decreasing the contrast of land-sea surface temperature and pressure. This results in the marked anomalies of north and northeast winds over eastern and southern China and the surrounding oceans in summer, thereby weakening the EASM. The summer mean precipitation averaged over the EAMR reduces by 12%. The changes in non-East Asian aerosol emissions play a more important role in inducing the changes of local temperature and pressure, and thus significantly exacerbate the weakness of the EASM circulation due to local aerosol changes. The weakening of circulation due to both is comparable, and even the effect of non-local aerosols is larger in individual regions. The changes of local and non-local aerosols contribute comparably to the reductions in precipitation over oceans, whereas cause opposite changes over eastern China. Our results highlight the importance of aerosol changes outside East Asia in the impact of the changes of anthropogenic aerosols on EASM.

  4. Genetic diversity of Diaphorina citri and its endosymbionts across east and south-east Asia.

    Science.gov (United States)

    Wang, Yanjing; Xu, Changbao; Tian, Mingyi; Deng, Xiaoling; Cen, Yijing; He, Yurong

    2017-10-01

    Diaphorina citri is the vector of 'Candidatus Liberibacter asiaticus', the most widespread pathogen associated huanglongbing, the most serious disease of citrus. To enhance our understanding of the distribution and origin of the psyllid, we investigated the genetic diversity and population structures of 24 populations in Asia and one from Florida based on the mtCOI gene. Simultaneously, genetic diversity and population structures of the primary endosymbiont (P-endosymbiont) 'Candidatus Carsonella ruddii' and secondary endosymbiont (S-endosymbiont) 'Candidatus Profftella armatura' of D. citri were determined with the housekeeping genes. AMOVA analysis indicated that populations of D. citri and its endosymbionts in east and south-east Asia were genetically distinct from populations in Pakistan and Florida. Furthermore, P-endosymbiont populations displayed a strong geographical structure across east and south-east Asia, while low genetic diversity indicated the absence of genetic structure among the populations of D. citri and its S-endosymbiont across these regions. The 'Ca. C. ruddii' is more diverse and structured than the D. citri and the 'Ca. P. armatura' across east and south-east Asia. Multiple introductions of the psyllid have occurred in China. Management application for controlling the pest is proposed based on the genetic information of D. citri and its endosymbionts. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

  5. East African rarities committee report | Fisher | Scopus: Journal of ...

    African Journals Online (AJOL)

    East African Rarities Committee (EARC) Special Report Species included for East African countries in Britton (1980) which have since been considered unacceptable. East African Rarities Committee Report 2013–2015. Full Text: EMAIL FREE FULL TEXT EMAIL FREE FULL TEXT · DOWNLOAD FULL TEXT DOWNLOAD ...

  6. Tekstil Atıksularının Gideriminde Atık Döküm Kumlarının Kullanımı / Using of Waste Foundry Sands in Removal of Textile Wastewater

    Directory of Open Access Journals (Sweden)

    ELİF HATİCE GÜRKAN

    2012-12-01

    öküm kumlarının, tekstil endüstrisi atık sularında renk gideriminde adsorbent olarak kullanılması amaçlanmaktadır. Using of Waste Foundry Sands in Removal of Textile Wastewater Nowadays, the accelerating need of water due to usage of water in industralized countries and global warming is causing all water sources to be exhausted. The effects the industrial wastewater made to the nature are important level, changer of natural balance, and sometimes non returned position. By reusing the treated the wastewater, not only the consumption of natural water sources has been prevented, but also the amount of discharged treated wastewater and its effects to the environment has been decreased. The wastewater resulted from industries shows big differences according to the wastewater in houses in the conditions of resource, amount, and character. So output water of the industry establishment has to be purified to prevent not to dirty natural water places. Textile industry is one of the biggest industries of Turkey and it consumes Access amount of water. As there are several methods and technologies used in this sector due to the different raw materials and various chemicals, the wastewaters obtained vary related to the products produced. The most prominent feature of textile industry wastewater is contained high amounts of organic and inorganic chemicals, and high total organic carbon (TOC, chemical oxygen demand (COD and intense color. The discharge of dyes into the receiving waters constitutes only a small portion of water pollution. However the presence of very low concentrations of dyes in receiving waters is aesthetically undesirable. Therefore, treatment processes removing dyes from textile effluents have become important in order to conserve receiving waters. In this study is to investigate using the adsorpsion method of removal with waste foundry sands, which are used expecially dye nd textile industries and are an important polluting agent in the waste water dumped into

  7. Nuclear age in the Middle East

    Energy Technology Data Exchange (ETDEWEB)

    Yiftah, S

    1976-01-01

    The book analyses, clarifies and summarises, from various aspects, some of the many questions concerning the motivation, the meaning, the economics, the dangers and the risks of introducing nuclear technology into the Middle East area following the recent agreements between some Mid Eastern countries and the United States, France, Germany and the U.S.S.R. about the supply of nuclear power reactors and nuclear fuel to the Middle East. The recent strong nuclear prgrams of countries such as India and Iran, who have wide-ranging ties with the Mid-Eastern countries, coupled with the huge revenues of petrodollars by the Arab countries of the area, together with the dangers of another 1973-type oil embargo are discussed and the triple crises of energy, ecology and nuclear weapons proliferation are considered.

  8. Measurement of Radiated Power Loss on EAST

    International Nuclear Information System (INIS)

    Duan Yanmin; Hu Liqun; Mao Songtao; Xu Ping; Chen Kaiyun; Lin Shiyao; Zhong Guoqiang; Zhang Jizong; Zhang Ling; Wang Liang

    2011-01-01

    A type of silicon detector known as AXUV (absolute extreme ultraviolet) photodiodes is successfully used to measure the radiated power in EAST. The detector is characterized by compact structure, fast temporal response (<0.5 s) and flat spectral sensitivity in the range from ultra-violet to X-ray. Two 16-channel AXUV arrays are installed in EAST to view the whole poloidal cross-section of plasma. Based on the diagnostic system, typical radiation distributions for both limiter and divertor plasma are obtained and compared. As divertor detachment occurs, the radiation distribution in X-point region is observed to vary distinctly. The total radiation power losses in discharges with different plasma parameters are briefly analyzed.

  9. The post-war Middle East

    International Nuclear Information System (INIS)

    Tempest, P.

    1992-01-01

    The Middle East remains today the global energy fulcrum. One year after the Persian Gulf war, the region is in greater turmoil and political uncertainty than it has known in modern times. The Iraqi invasion of Kuwait and subsequent external military intervention forced neighboring states to question the need for a foreign military presence in the future. The rift between the secular revolutionary states in the region led by Iraq, Libya, Yemen, Algeria, and Syria and the traditional monarchy of Saudi Arabia and the emirates of the gulf has widened. Egypt provides, at present, an uncomfortable bridge. The balance of political forces may be shifting. This paper attempts to answer the following questions: Where will we see the new leadership in the Middle East? Will it again play a role through the Organization of Petroleum Exporting Countries and determination of the oil price in shaping the structure of global energy supply and demand?

  10. Collaboration with East African security organisations

    DEFF Research Database (Denmark)

    Nordby, Johannes Riber; Jacobsen, Katja L.

    2012-01-01

    of the concept. At the same time the three organisations represent different constellations of member nations and thus different national interests, and locally they have different legitimacy and political strength. Thus, when choosing collaboration partners for a security project it is not simply a question......When it comes to understanding the concept of security and the way fragile security situations should be solved, the difference is big. While EASF – the East African Standby Force – is a regular military force with a rather traditional, military perception of the concept of security, EAC (East...... African Community) and IGAD (Intergovernmental Authority on Development) have broader perceptions of the concept. According to EAC, security also concerns matters such as policy reform, legislation, education and infrastructure. IGAD considers food security and environmental and economic issues as part...

  11. The nuclear age in the Middle East

    International Nuclear Information System (INIS)

    Yiftah, Shimon.

    1976-01-01

    The book analyses, clarifies and summarises, from various aspects, some of the many questions concerning the motivation, the meaning, the economics, the dangers and the risks of introducing nuclear technology into the Middle East area following the recent agreements between some Mid Eastern countries and the United States, France, Germany and the U.S.S.R. about the supply of nuclear power reactors and nuclear fuel to the Middle East. The recent strong nuclear prgrams of countries such as India and Iran, who have wide-ranging ties with the Mid-Eastern countries, coupled with the huge revenues of petrodollars by the Arab countries of the area, together with the dangers of another 1973-type oil embargo are discussed and the triple crises of energy, ecology and nuclear weapons proliferation are considered. (B.G.)

  12. Pipelines to power South East Asia

    Energy Technology Data Exchange (ETDEWEB)

    Scholes, W

    1994-07-01

    European, North American and Australian pipeline companies are busy building pipelines to transport natural gas to power stations throughout South East Asia. Many countries, such as Thailand, Malaysia, Singapore and Indonesia, have economies expanding at more than eight percent a year. Cambodia and Laos are awaiting energy development. Myanmar will not only benefit from the global economic expansion but from the flourishing economies of nearby Thailand and Malaysia which are now investing in neighbouring countries, while their national petroleum companies are starting to operate worldwide. It is the ever expanding rush of industrialisation, urbanisation and the move to raise living standards throughout the region that is accelerating the need for more power stations, both gas and coal-fired, throughout South East Asia. (author)

  13. Brief communication: Drought likelihood for East Africa

    Science.gov (United States)

    Yang, Hui; Huntingford, Chris

    2018-02-01

    The East Africa drought in autumn of year 2016 caused malnutrition, illness and death. Close to 16 million people across Somalia, Ethiopia and Kenya needed food, water and medical assistance. Many factors influence drought stress and response. However, inevitably the following question is asked: are elevated greenhouse gas concentrations altering extreme rainfall deficit frequency? We investigate this with general circulation models (GCMs). After GCM bias correction to match the climatological mean of the CHIRPS data-based rainfall product, climate models project small decreases in probability of drought with the same (or worse) severity as 2016 ASO (August to October) East African event. This is by the end of the 21st century compared to the probabilities for present day. However, when further adjusting the climatological variability of GCMs to also match CHIRPS data, by additionally bias-correcting for variance, then the probability of drought occurrence will increase slightly over the same period.

  14. Online Plasma Shape Reconstruction for EAST Tokamak

    International Nuclear Information System (INIS)

    Luo Zhengping; Xiao Bingjia; Zhu Yingfei; Yang Fei

    2010-01-01

    An online plasma shape reconstruction, based on the offline version of the EFIT code and MPI library, can be carried out between two adjacent shots in EAST. It combines online data acquisition, parallel calculation, and data storage together. The program on the master node of the cluster detects the termination of the discharge promptly, reads diagnostic data from the EAST mdsplus server on the completion of data storing, and writes the results onto the EFIT mdsplus server after the calculation is finished. These processes run automatically on a nine-nodes IBM blade center. The total time elapsed is about 1 second to several minutes, depending on the duration of the shot. With the results stored in the mdsplus server, it is convenient for operators and physicists to analyze the behavior of plasma using visualization tools.

  15. The Middle East in the year 2000

    International Nuclear Information System (INIS)

    Henderson, S.

    1996-02-01

    The Middle East in the year 2000 provides all insight into the political and economic changes taking place in the region and explains what they mean for the oil and gas industry. This comprehensive report combines published forecasts with expert comment and analysis, making it a highly practical business guide. With oil and gas at the heart of its discussion it looks in detail at: the likely shape of the Middle East into the next century, with a country-by-country review; the declared aspirations of Middle Eastern countries, with likely economic trends including oil production; the complete political and economic picture and what the future may hold; the long- and short-term future for oil; how oil prices will change over the coming years; the impact of non-Opec production on the region; the opportunities and competitive advantages for companies wanting to do business in the region; fundamentalism versus democracy; and various political scenarios. (author)

  16. Brief communication: Drought likelihood for East Africa

    Directory of Open Access Journals (Sweden)

    H. Yang

    2018-02-01

    Full Text Available The East Africa drought in autumn of year 2016 caused malnutrition, illness and death. Close to 16 million people across Somalia, Ethiopia and Kenya needed food, water and medical assistance. Many factors influence drought stress and response. However, inevitably the following question is asked: are elevated greenhouse gas concentrations altering extreme rainfall deficit frequency? We investigate this with general circulation models (GCMs. After GCM bias correction to match the climatological mean of the CHIRPS data-based rainfall product, climate models project small decreases in probability of drought with the same (or worse severity as 2016 ASO (August to October East African event. This is by the end of the 21st century compared to the probabilities for present day. However, when further adjusting the climatological variability of GCMs to also match CHIRPS data, by additionally bias-correcting for variance, then the probability of drought occurrence will increase slightly over the same period.

  17. Pipelines to power South East Asia

    International Nuclear Information System (INIS)

    Scholes, W.

    1994-01-01

    European, North American and Australian pipeline companies are busy building pipelines to transport natural gas to power stations throughout South East Asia. Many countries, such as Thailand, Malaysia, Singapore and Indonesia, have economies expanding at more than eight percent a year. Cambodia and Laos are awaiting energy development. Myanmar will not only benefit from the global economic expansion but from the flourishing economies of nearby Thailand and Malaysia which are now investing in neighbouring countries, while their national petroleum companies are starting to operate worldwide. It is the ever expanding rush of industrialisation, urbanisation and the move to raise living standards throughout the region that is accelerating the need for more power stations, both gas and coal-fired, throughout South East Asia. (author)

  18. JPRS Report, Near East & South Asia

    Science.gov (United States)

    1991-05-10

    But Something like the joke-either the oppressor horseman first of all we must stress the differences between us and will die or the horse will die...elements within the Bangladesh elections were countermanded in two following deaths of polity to the democratic process. This attributed to the two...THE FRONTIER POST American and British aims in the Middle East, which in English 4 Mar 91 p 9 include the complete destruction of Iraq, the death of

  19. THE VARIABLE REFLECTION NEBULA CEPHEUS A EAST

    International Nuclear Information System (INIS)

    Hodapp, Klaus W.; Bressert, Eli

    2009-01-01

    We report K'-band imaging observations of the reflection nebula associated with Cepheus A East covering the time interval from 1990 to 2004. Over this time the reflection nebula shows variations of flux distribution, which we interpret as the effect of inhomogeneous and varying extinction in the light path from the illuminating source HW2 to the reflection nebula. The obscuring material is located within typical distances of ∼ 10 AU from the illuminating source.

  20. Turkey and Stability in East Asia

    Science.gov (United States)

    2016-12-01

    military growth. China will try to expel the United States from the region, and then conflict is inevitable . Liberals think that the economic...ascendance in East Asia. Realists view the rise of China as a reason for conflict and power struggle in the region; a rising power inevitably leads to an... conflict is inevitable because, according to Kenneth Neal Waltz, “a state that is amassing instruments of war, even for its own defensive, is cast

  1. Near East/South Asia Report

    Science.gov (United States)

    1987-03-26

    all forces having an interest m the solution and an interest in society there is an alliance and partnership to confront the danger overtaking the...must be partnership and consensus in order to reach a solution. I doubt that President al-Jumayyil can at this stage settle affairs in East Beirut by...mountains, followed by another, in 1977 in Dhofar. ! Three conservation projects were undertaken, with the sup- port of the WWF and IUCN, which

  2. JPRS Report, Near East & South Asia.

    Science.gov (United States)

    1989-06-06

    as their Big Brother or the founder of the theory behind their move- ment. Of course, this change is not easy. There is resistance to it, and many...secretary of the UGET, and Hamadi El Euch, spokesman for the UGTE , by Nejib Lakenji; date and place not given] [Text] Following outbreaks of violence...1989 42 NEAR EAST of Tunisian Students], represented by its general secre- tary, Abdellatif Mekki; and the UGTE [Tunisian Gen- eral Student Union

  3. JPRS Report, Near East and South Asia.

    Science.gov (United States)

    1991-07-31

    Territories [Jerusalem AL-USBU’ AL-JADID 15 Jun] .. 25 Merchants Interviewed on Chamber of Commerce Elections...043 26 NEAR EAST 31 July 1991 deceased and the armed men during which they opened holding Chamber of Commerce elections in the West fire on Khayyal...passing through the after having given Chamber of Commerce officials a area and fled immediately. refusal to hold the elections? A climate of resentment

  4. Political opposition in patriarchal East London

    OpenAIRE

    Atkinson, D

    2010-01-01

    This paper describes the growing level of politicization in East London in the 1950s, and the way this affected the patriarchal normative system, which prevailed in urban administration. Patriarchalism, as a system, was susceptible of different interpretations by white municipal officials, and their response to black political opposition ranged from liberal forbearance to rigid and uncompromising intolerance. Black leaders’ attitudes to the patriarchal order were similarly nuan...

  5. Sponges from Clipperton Island, East Pacific

    OpenAIRE

    van Soest, R.W.M.; Kaiser, K.L.; van Syoc, R.

    2011-01-01

    Twenty sponge species (totalling 190 individuals) were collected during the 1938, 1994 and 2004/5 expeditions to the remote island of Clipperton in the East Pacific Ocean. Seven species are widespread Indo-Pacific sponges; nine species comprise sponges new to science; four species were represented only by small thin patches insufficient for proper characterization and could be only determined to genus. The new species may not be necessarily endemic to the island, as several show similarities ...

  6. Upgrade of ICRF heating system on EAST

    International Nuclear Information System (INIS)

    Chen Gen; Zhao Yanpin; Mao Yuzhou

    2013-01-01

    ICRF (Ion Cyclotron Range of Frequency) heating is an essential heating and current drive tool on EAST (Experimental Advanced Superconducting Tokamak). The high-power steady-state transmitters were designed as a part of research and development of ICRF heating system which aimed at output power of 1.5 MW for 1000 s in a frequency range of 25 to 70 MHz. There are 3 stage power amplifiers for each transmitter. Tube TH525A and TH535 were chosen for drive power amplifier (DPA) and final power amplifier (FPA), respectively. The power supply system of DPA and FPA were upgraded by using reliable PSM high voltage sources, whose response time is less than 5 μs. The ICRF system, which consists of 8 transmitters, will give out more than 10 MW total output power in the future. Four of them have been already fabricated, and another four are under construction. Three liquid stub tuners are used for impedance matching between antennas and transmitters, which can be only tuned shot to shot. There are two fast wave heating antennas which are assembled at I port and B port on EAST. Several projects are in progress including fast response impedance matching, distributed data acquisition and control system and so on for EAST ICRF heating system. (author)

  7. Detrital Zircons Split Sibumasu in East Gondwana

    Science.gov (United States)

    Zhang, X.; Chung, S. L.

    2017-12-01

    It is widely accepted that Sibumasu developed as a united terrane and originated from NW Australian margin in East Gondwana. Here we report new detrital zircon U-Pb-Hf isotopic data from Sumatra that, in combination with literature data, challenge and refute the above long-held view. In particular, the East and West Sumatra terranes share nearly identical Precambrian to Paleozoic detrital zircon age distributions and Hf isotopes, indicating a common provenance/origin for them. The Sumatra detrital zircons exhibit a prominent population of ca. 1170-1070 Ma, indistinguishable from those of the Lhasa and West Burma terranes, with detritus most probably sourcing from western Australia. By contrast, Sibuma (Sibumasu excluding Sumatra) detrital zircons display a prevailing population of ca. 980-935 Ma, strongly resembling those of the western Qiangtang terrane, with detrital materials most likely derived from Greater India and Himalayas. Such markedly distinct detrital zircon age profiles between Sumatra and Sibuma require disparate sources/origin for them, provoking disintegration of the widely-adopted, but outdated, term Sibumasu and thus inviting a new configuration of East Gondwana in the early Paleozoic, with Sumatra and West Burma lying outboard the Lhasa terrane in the NW Australian margin and Sibuma situated in the northern Greater Indian margin. More future investigations are needed to establish the precise rifting and drifting histories of Sumatra and Sibuma, as two separated terranes, during the breakup of Gondwana.

  8. Comparison of East Asian winter monsoon indices

    Directory of Open Access Journals (Sweden)

    Gao Hui

    2007-01-01

    Full Text Available Four East Asian winter monsoon (EAWM indices are compared in this paper. In the research periods, all the indices show similar interannual and decadal-interdecadal variations, with predominant periods centering in 3–4 years, 6.5 years and 9–15 years, respectively. Besides, all the indices show remarkable weakening trends since the 1980s. The correlation coefficient of each two indices is positive with a significance level of 99%. Both the correlation analyses and the composites indicate that in stronger EAWM years, the Siberian high and the higher-level subtropical westerly jet are stronger, and the Aleutian low and the East Asia trough are deeper. This circulation pattern is favorable for much stronger northwesterly wind and lower air temperature in the subtropical regions of East Asia, while it is on the opposite in weaker EAWM years. Besides, EAWM can also exert a remarkable leading effect on the summer monsoon. After stronger (weaker EAWM, less (more summer precipitation is seen over the regions from the Yangtze River valley of China to southern Japan, while more (less from South China Sea to the tropical western Pacific.

  9. Middle East gas utilization and export potential

    International Nuclear Information System (INIS)

    Cornet-Gandolphe, S.

    1995-01-01

    There is huge gas supply potential in the Middle East, which possesses over one third of the world's natural gas reserves. However, marketed production represents only 6% of the world total, demonstrating that gas resources in the Middle East are under utilized. The value of these resources will be realized only if the gas finds a commercial outlet that guarantees proper return on investments for gas producers and the best possible use of this nonrenewable resource for governments. Apart from the chemical sector, which has provided a good outlet for natural gas, the development of natural gas resources in the region has been very limited historically, inhibited by many factors linked to the resource itself and to the characteristics of the region. However, natural gas in the Middle East is now at a crossroads, facing both major challenges and significant opportunities. The region, which currently plays only a marginal role on the world gas market, has the potential to become a leading world supplier, provided a number of political and economic conditions are fulfilled. This paper discusses some of the challenges that Middle Eastern countries face in trying to develop their natural gas resources. It reviews development potential for Middle Eastern gas reserves, whether for local use and/or exports, and it highlights future opportunities. (Author)

  10. The cryogenic control system of EAST

    International Nuclear Information System (INIS)

    Zhuang, M.; Hu, L.B.; Zhow, Z.W.; Xia, G.H.

    2012-01-01

    Highlights: ► A reliable and flexible duplex control system is required for cryogenic system. ► The cryogenic control system is based on Delta-V DCS. ► It has been proved to be an effective way to control cryogenic process. ► It will provide useful experience and inspiration for the development in the cryogenic control engineering. - Abstract: A large scale helium cryogenic system is one of the key components for the EAST tokamak device for the cooling of PF and TF coils, structures, thermal shields, buslines, current leads and cryopumps. Since the cooling scheme of the EAST cryogenic system is fairly complicated, a reliable and flexible control system is required for cryogenic system. The cryogenic control system is based on DeltaV DCS which is the process control software developed by Emerson Company. The EAST cryogenic system has been in operation for four years and has been proved to be safe, stable and energy saving by the past 7 experiments. This paper describes the redundant control network, hardware configuration, software structure, auxiliary system and the new development in the future.

  11. Damage caused due to foundry smoke

    Energy Technology Data Exchange (ETDEWEB)

    1891-01-01

    A detailed analysis of an air pollution event which occurred in 1891 in the vicinity of a superphosphate plant is given. The logic and tests used to implicate HF as the causative agent of environmental stress are detailed thoroughly.

  12. Configuring and Exploring the Foundry Trade Space

    Science.gov (United States)

    2012-04-01

    manufacturability implies the existence of a process plan and available resources, the MFE is closely related to the PPE and may internally embody...the PPE in its construction. For example, the MFE can answer queries as to a component’s manufacturability by attempting to generate a process plan...make it manufacturable. Conversely, the MFE could be built up from higher level heuristics and surrogate models, but these would ultimately need to

  13. 76 FR 21695 - Proposed Flood Elevation Determinations

    Science.gov (United States)

    2011-04-18

    ... County. At the Betts Spring None +571 Branch and Bradford Creek confluence. Big Cove Creek Approximately.... Approximately 0.7 mile None +677 upstream of the Big Cove Creek confluence. Blue Spring Creek Approximately 400... Road. Approximately 450 feet None +748 upstream of Spragins Hollow Road Northwest. East Fork Pinhook...

  14. An Overview of the EAST Project

    International Nuclear Information System (INIS)

    Songtao Wu

    2006-01-01

    The China national project of Experimental Advanced Superconducting Tokamak (EAST) has been in its final engineering phase in the Institute of Plasma Physics, the Chinese Academy of Sciences (ASIPP). The year of 2006 is the important year for the EAST project. After six years hard work, the first engineering commissioning of EAST superconducting tokamak began with vacuum pumping on 7, Feb. The first charge of one of the PF coils was made on 13, Mar. The EAST superconducting tokamak is a full superconducting tokamak with a non-circle cross-section of the vacuum vessel and active cooling plasma facing components. The scientific and the engineering missions of the EAST project are to study physics issues of the advanced steady-state tokamak operations and to establish technology basis of full superconducting tokamaks. The EAST project features both superconducting toroidal field (TF) coils and poloidal field (PF) coils, continuous working (CW) non-inductive plasma current drive and heating systems, flexible and reliable PF system design to shape and control plasmas with big elongations and triangularity, real time data collection and feedback for steady-state profile control, active cooling and changeable plasma facing components (PFC) and advanced diagnostic measurements. During the past five years, the main R (and) D mainly focused on the design, fabrication and test of 16 kA CICC (Cable-in-Conduit Conductor) and the large scale superconducting magnet has been completed. The test results shown the performances of all superconducting magnets are well acceptable. For the deadlock configuration among the main components of the superconducting tokamak, the first commissioning was taken without the vacuum vessel ducts for easily disassembling if some important problems were found. In the commissioning, the TF system was charged up to 8 kA in 5000 s and the toroidal field at the major radius of 1.7 m is 2 T, which is 60% of the designed value. The reason why the TF system

  15. The Middle East WMDFZ: hopes and fears

    International Nuclear Information System (INIS)

    Hautecouverture, Benjamin

    2014-05-01

    The 3. Preparatory Committee (PrepCom) for the 2015 Nuclear Non-Proliferation Treaty (NPT) Review Conference took place in New York between 28 April and 9 May 2014. Despite the failure to hold a conference in Helsinki in 2013 on a zone free of weapons of mass destruction and their delivery systems (WMDFZ) in the Middle East, due to a lack of consensus among States, the issue of the Middle East did not unduly disrupt this year's round of debates. This is in contrast to the Geneva PrepCom in the spring of 2013, where the Egyptian delegation's decision to leave the second session before the close first checked the momentum generated by the adoption of the 2010 Action Plan. The argument put forward by the Egyptian delegation was the lack of progress on the implementation of a commitment in the document to bring together all of the States in the region at a conference in 2012 on the Middle East WMDFZ project with the support of a facilitator. Although bilateral and multilateral (the Glion process) negotiations are in progress out of the spotlight under the auspices of Ambassador Laajava on both the agenda and outcome of a future conference, as well as on its procedural aspects, it is impossible to say with any certainty that a conference in Helsinki bringing together all of the States in the region will take place before the 2015 NPT Review Conference. One of the principal weaknesses of the Middle East WMDFZ project is its inscription almost twenty years ago in the framework of the NPT (with the resolution 'on the Middle East' of the 1995 Review and Extension Conference). The fact that Israel, a key State in the region, was absent at that time and is still absent today has naturally hindered the progress of this issue from review conference to review conference. The NPT forum is clearly inappropriate for dealing with the multiple regional security issues involved in the project. Yet, no alternative to the NPT currently exists, despite the fact that the real substance of

  16. Enhancement of EAST plasma control capabilities

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, Bingjia, E-mail: bjxiao@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei (China); Yuan, Qiping; Luo, Zhengping; Huang, Yao; Liu, Lei; Guo, Yong; Pei, Xiaofang; Chen, Shuliang [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Humphreys, D.A.; Hyatt, A.W. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Mueller, Dennis [Princeton Plasma Physics Laboratory, Princeton, NJ (United States); Calabró, G.; Crisanti, F. [ENEA UnitàTecnicaFusione, C.R. Frascati, Via E. Fermi 45, 00044 Frascati, Roma (Italy); Albanese, R.; Ambrosino, R. [CREATE, Università di Napoli Federicao II, Università di Cassino and Università di Napoli Parthenope, Via Claudio 19, 80125 Napoli (Italy)

    2016-11-15

    Highlights: • Parallel plasma equilibrium reconstruction using GPU for real-time control on EAST. • Vertical control using Bang-bang + PID method to improve the response and minimize the oscillation caused by the latency. • Quasi-snow flake divertor plasma configuration has been demonstrated on EAST. - Abstract: In order to improve the plasma control performance and enhance the capability for advanced plasma control, new algorithms such as PEFIT/ISOFLUX plasma shape feedback control, quasi-snowflake plasma shape development and vertical control under new vertical control power supply, have been implemented and experimentally tested and verified in EAST 2014 campaign. P-EFIT is a rewritten version of EFIT aiming at fast real-time equilibrium reconstruction by using GPU for parallelized computation. Successful control using PEFIT/ISOFLUX was established in dedicated experiment. Snowfldivertor plasma shape has the advantage of spreading heat over the divertor target and a quasi-snowflake (QSF) configuration was achieved in discharges with I{sub p} = 0.25 MA and B{sub t} = 1.8T, κ∼1.9, by plasma position feedback control. The shape feedback control to achieve QSF shape has been preliminary implemented by using PEFIT and the initial experimental test has been done. For more robust vertical instability control, the inner coil (IC) and its power supply have been upgraded. A new control algorithm with the combination of Bang-bang and PID controllers has been developed. It is shown that new vertical control power supply together with the new control algorithms results in higher vertical controllability.

  17. A South-East Asian perspective.

    Science.gov (United States)

    Koh, D; Chia, S E; Jeyaratnam, J

    2000-01-01

    In order to discuss the subject of occupational medicine in the next century, changes in the present demographic profile and work activity must be considered first. Only then can the challenges be identified, and appropriate strategies be formulated to respond to them. In the diverse countries of South-East Asia, improved health and work conditions, the advent of new technology, a redistribution of work activity, and an ageing workforce can be expected. Two other factors that have specific impact in the region are the recent financial crisis and the occurrence of an international environmental haze from forest fires. The various countries in South-East Asia, which are in different stages of development, and have different problems and priorities, will respond differently to the demands for occupational health. It is likely that there will be a shift in the focus of current health care activities towards specific work sectors, the recognition of new hazards at work, the identification of newly emerging work related diseases, and an increase in health promotion in the workplace. Hopefully, there will be improved training of health professionals to ensure that there are adequate numbers and that they are well prepared to face these changes. Responsive, appropriate and well enforced labour legislation to protect the health of all workers, and international cooperation in occupational and environmental health are also required. As global and regional economic conditions continue to remain unstable and the impact of the crisis further takes its course, the final effect on occupational health in South-East Asia remains to be seen.

  18. Cerebral cortices of East african early hominids.

    Science.gov (United States)

    Falk, D

    1983-09-09

    An endocast of the frontal lobe of a reconstructed skull, which is approximately 2 million years old, from the Koobi Fora region of Kenya appears to represent the oldest human-like cortical sulcal pattern in the fossil record, while the endocast from another skull from the same region produces an endocast that appears apelike in its frontal lobe and similar to endocasts from earlier South African australopithecines. New analysis of paleoanatomical evidence thus indicates that at least two taxa of early hominids coexisted in East Africa.

  19. Gender Inequality in North East India

    OpenAIRE

    Mahanta, Bidisha; Nayak, Purusottam

    2013-01-01

    The present paper is an attempt to analyze the status of gender inequality in North East India using various indicators based on secondary data. The study reveals that the northeast is better off than that of the nation as a whole in terms of gender equality. However inequality between women and men exists in the region in spite of the predominance of various ethnic groups who by and large do not believe in sex discrimination. The study reveals that women are relatively disempowered and enjoy...

  20. The genus Rhaponticum in East Asia

    Directory of Open Access Journals (Sweden)

    Gorovoy, P.

    2010-12-01

    Full Text Available The genus Rhaponticum in East Asia has always been a taxon for discussion. Rhaponticum carthamoides from East Siberia comprises three subspecies: carthamoides, chamarensis and orientale. Even though they differ in morphology, they do not have isolated areas. Rhaponticum satzyperovii was recently described and its author pointed out its affinity with Rh. uniflorum. Plant height, stem indumentum, and radical and stem leaf dissection were signaled as the diagnostic characters. Our present study on living and herbarium specimens of Rh. satzyperovii shows that the diagnostic characters are not consistent. The species area was also claimed to be an argument for considering Rh. satzyperovii a distinct species. This area covers the south of the Primorye Province in the Far East of Russia with some locations in the adjacent Jewish Autonomous Region and in China. In our study, the area of Rh. satzyperovii is found to be within the area of Rh. uniflorum and thereafter they turned out to have no disjunction. In East Asia, Rh. uniflorum is characterized by a wide range of morphological variability. We suggest that Rh. satzyperovii should be included within Rh. uniflorum without any taxonomic rank.El género Rhaponticum en el Este de Asia ha sido siempre un taxón discutido. Rhaponticum carthamoides del Este de Siberia incluye tres subespecies: carthamoides, chamarensis y orientale. Aunque difieren en su morfología, sus áreas no están aisladas. Rhaponticum satzyperovii fue descrito recientemente y su autor señaló su afinidad con Rh. uniflorum. Los caracteres diagnósticos fueron la altura de la planta, el indumento del tallo y las divisiones de las hojas basales y caulinares. Nuestro estudio de plantas vivas y muestras de herbario de Rh. satzyperovii muestra que los caracteres diagnósticos no son consistentes. El área de distribución también se argumentó para considerar Rh. satzyperovii una especie diferente. El área cubre el sur de la provincia de

  1. [International migration in the Middle East].

    Science.gov (United States)

    Beauge, G

    1985-01-01

    This special issue contains a selection of 12 papers by various authors on aspects of international migration to the Middle East. Papers are included on the impact of migration on socioeconomic development, income distribution, and rural capitalization in Egypt; migration from rural Lebanon; the effect of emigration on Pakistan; Indian workers in Oman; inter-Arab migration and development; the role of the state in migration in the Arab peninsula; the dynamics of manpower in Kuwait; the Iraqi model and Arab unity; and the impact of this migration on the concept of the New Economic Order.

  2. Middle east gas: supply source of Europe

    International Nuclear Information System (INIS)

    Vivies, P. de

    1995-01-01

    The evolution of gas demand, the decreasing of reserves leads to the question of European future needs satisfaction. The european market can call on the russian production or middle east production. Iran has the most important reserves but the needs of the population can limit the gas supply. Yemen and Oman which have less important reserves but also less important needs to satisfy can be a serious alternative; Abu dhabi reserves are destined to asia market. The qatar has the most important gas offshore field in the world. The LNG (liquefied natural gas) seems to have a better position than gas pipeline to dispatch gas towards Europe

  3. East-West cooperation at CERN

    CERN Document Server

    2002-01-01

    From left to right: H. Bokemeyer, in charge of physics for INTAS, J. Sinnaeve, INTAS' general secretary and R. Landua, ATHENA spokesman, visit the ATHENA experiment installations. Heads of INTAS (International Association for the promotion and cooperation of the new independent states of the former Soviet Union) visited CERN on 11 October. This association is in charge of preserving and promoting the scientific potential of the former Soviet Union countries through a cooperation between East and West. In recents years, a certain number of projects related to the LHC experiments have been co-financed by INTAS. The support for young researchers coming from these countries is also a big success.

  4. Extension of operational limits on EAST

    International Nuclear Information System (INIS)

    Gao Xiang; Li Jiangang; Wan Baonian; Zhao Junyu; Hu Liqun; Liu Haiqing; Jie Yinxian; Xu Qiang; Wu Zhenwei; Yang Yu; Gong Xianzu; Shen Biao; Hu Jiansheng; Shi Yuejiang; Ling Bili; Wang Jun; Sajjad, S.; Zang Qing; Gao Wei; Zhang Tao; Yu Yaowei; Yang Yao; Han Xiaofeng; Shi Nan; Ming Tingfeng; Ti Ang; Zhang Wenyang; Xu Guosheng; Chen Junling; Luo Guangnan; Zhang Xiaodong; Mao Jianshan; Wan Yuanxi

    2007-01-01

    The first plasma has been achieved successfully in the Experimental Advanced Superconducting Tokamak (EAST). Boronization by the glow discharge (GDC) method was studied in experiments. The plasma performance was obviously improved by GDC boronization. Extension of the operational region and improvement in the plasma performance were obtained. Sawtooth discharges were observed by means of soft x-ray signals, electron cyclotron emission signals and line averaged electron density after boronization. Lower q a and more stable operation were also achieved following GDC boronization. The plasma current ramp-up rate was also improved as a result of decreased impurity content and low averaged loop voltage due to boronization

  5. East, West German gas pipeline grids linked

    International Nuclear Information System (INIS)

    Anon.

    1992-01-01

    This paper reports that Ruhrgas AG, Essen, has started up the first large diameter gas pipeline linking the gas grids of former East and West Germany. Ruhrgas last month placed in service a 40 in., 70 km line at Vitzeroda, near Eisenach, linking a new Ruhrgas pipeline in Hesse state with a 330 km gas pipeline built last year in Thuringia and Saxony states by Erdgasversorgungs GmbH (EVG), Leipzig. The new link enables pipeline operator EVG to receive 70 bcf/year of western European gas via Ruhrgas, complementing the 35 bcf/year of gas coming from the Commonwealth of Independent States via Verbundnetz Gas AG (VNG), Leipzig

  6. ISSN 2073 ISSN 2073 9990 East Cent. Afr. J. s 9990 East Cent. Afr.

    African Journals Online (AJOL)

    Hp 630 Dual Core

    Countries in the Afro Asian stone belt (stretching from Egypt and Sudan, through the Middle East, India, Pakistan, Burma, Thailand, Indonesia and the Philippines) falling within the .... BJU International, 89(suppl.1): 62 68,. 2002. 10. J.U.V. Monu, Pattern of urolithiasis in Benin City, Nigeria. Journal of the national medical.

  7. ISSN 2073 ISSN 2073-9990 East Cent. Afr. J. surg. (Online) 90 East ...

    African Journals Online (AJOL)

    DELL

    East and Central African Journal of Surgery. ... as the 3D cone beam CT machines which reduce exposure to irradiations, .... effect is closely related to the depth of impaction and height of the body of the mandible. ... extraction based on mere speculation or expectation of a sequelae, however a joint committee on third molar.

  8. ISSN 2073 ISSN 2073-9990 East Cent. Afr. J. s 9990 East Cent. Afr.

    African Journals Online (AJOL)

    Hp 630 Dual Core

    2016-08-01

    Aug 1, 2016 ... Congenital Diaphragmatic Hernia Outcomes in East frica: The Ethiopian Experience. Miliard Derbew ... One child was diagnosed with congenital pulmonary airway malformation (CPAM). In total, 10 (83.3%) of our patients were initially misdiagnosed. Only one patient .... Superficial Surgical Site infection. 2.

  9. ISSN 2073 ISSN 2073 9990 East Cent. Afr. J. s 9990 East Cent. Afr ...

    African Journals Online (AJOL)

    Hp 630 Dual Core

    East & Central African Journal of Surgery. Nov/Dec 2014 Vol. 19 (3). Pattern and and Outcome of Surgical Management of Postrenal cute Renal Failure Over. Three Years Period at Tikur nbessa Specialized Hospital. L. Samodai, D. ndualem, . Getasew. Addis Ababa University, School of Medicine, Department of Surgery.

  10. ISSN 2073 ISSN 2073-9990 East Cent. Afr. J. surg. (Online) 90 East ...

    African Journals Online (AJOL)

    DELL

    2005-04-12

    Apr 12, 2005 ... East and Central African Journal of Surgery. .... Any man who is over 40 years with a positive family history (Especially one with HPC-1 gene) warrants a ..... effects of fluid retention, venous & arterial thrombosis, cardiac toxicity, stroke. .... with insertion of an indwelling catheter or intermittent catheterization ...

  11. Book Review: Flora of Tropical East Africa | Bytebier | Journal of East ...

    African Journals Online (AJOL)

    Flora of Tropical East Africa Edited by H.J. Beentje & S.A. Ghazanfar. Polygalaceae by J. Paiva. Kew Publishing, Royal Botanic Gardens, Kew, UK, 2007. ISBN- 978 1 84246 191 4 (softbound). 61 pages. Dryopteridaceae by J.P. Roux, M. Shaffer-Fehre & B. Verdcourt. Kew Publishing, Royal Botanic Gardens, Kew, UK, 2007.

  12. ISSN 2073-9990 East Cent. Afr. J. s 9990 East Cent. Afr. J. s

    African Journals Online (AJOL)

    Prof Kakande

    COSECSA/ASEA Publication -East and Central African Journal of Surgery. .... Only the manner of skin closure varied. ... Table 1. Wound Closure Time. Mean wound closure time in group A was 244+8.20 seconds whereas mean wound ... They have been used on skin, bone, cartilage graft, and middle ear surgery, repair of.

  13. East Greenland Caledonides: stratigraphy, structure and geochronology: Lower Palaeozoic stratigraphy of the East Greenland Caledonides

    Directory of Open Access Journals (Sweden)

    Smith, M. Paul

    2004-12-01

    Full Text Available The Lower Palaeozoic stratigraphy of the East Greenland Caledonides, from the fjord region of North-East Greenland northwards to Kronprins Christian Land, is reviewed and a number of new lithostratigraphical units are proposed. The Slottet Formation (new is a Lower Cambrian quartzite unit, containing Skolithos burrows, that is present in the Målebjerg and Eleonore Sø tectonic windows, in the nunatak region of North-East Greenland. The unit is the source of common and often-reported glacial erratic boulders containing Skolithos that are distributed throughout the fjord region. The Målebjerg Formation (new overlies the Slottet Formation in the tectonic windows, and comprises limestones and dolostones of assumed Cambrian–Ordovician age. The Lower Palaeozoic succession of the fjord region of East Greenland (dominantly limestones and dolostones is formally placed in the Kong Oscar Fjord Group (new. Amendments are proposed for several existing units in the Kronprins Christian Land and Lambert Land areas, where they occur in autochthonous, parautochthonous and allochthonous settings.

  14. Monetary Cooperation in East Asia: Major Issues and Future Prospects

    Directory of Open Access Journals (Sweden)

    Jai-Won Ryou

    2004-06-01

    Full Text Available The Asian currency crisis in 1997 and the launch of the euro in 1999 made the possibility and desirability of introducing a regional currency union in East Asia a point of debate. At present, the empirical findings and policy implications of previous studies are mixed. We are still in need of theoretical and empirical studies that capture the salient features of East Asia, and give us reliable recommendations for incentive structures, configurations and policy instruments in monetary cooperation in its various stages. This paper aims to review major conceptual and empirical issues relevant to monetary cooperation in East Asia, including proposals for a regional cooperative framework for exchange rate stability or forming a currency union in the region. East Asian countries have no experience with any type of monetary cooperation and all we have are hypothetical predictions. Nevertheless, East Asian countries may be on the brink of an historical evolution to economic and monetary integration, as Europe was half a century ago. The progressive integration of markets in East Asia has conferred a commonality of economic interest upon the countries in the region. As the economic structures of East Asian countries converge with one another through closer ties of trade, investment and finance, the necessity for monetary cooperation will be more likely to emerge in the future. Monetary cooperation in East Asia will be a long process. East Asian countries should make efforts to build collective institutions in the beginning.

  15. Soccer: Moulding the Middle East and North Africa

    OpenAIRE

    Dorsey, J.M.

    2016-01-01

    Nowhere in the world has sports in general and soccer in particular played such a key role in the development of a region than in the Middle East and North Africa. Yet, the nexus of sports, politics and society is one area that Middle East studies with few exceptions have ignored. Similarly, sports studies have focused on all parts of the world with one exception: the Middle East and North Africa. Nonetheless, sports and particularly soccer has been in various parts of the Middle East key to ...

  16. Analysis of EAST tokamak cryostat anti-seismic performance

    International Nuclear Information System (INIS)

    Chen Wei; Kong Xiaoling; Liu Sumei; Ni Xiaojun; Wang Zhongwei

    2014-01-01

    A 3-D finite element model for EAST tokamak cryostat is established by using ANSYS. On the basis of the modal analysis, the seismic response of the EAST tokamak cryostat structure is calculated according to an input of the design seismic response spectrum referring to code for seismic design of nuclear power plants. Calculation results show that EAST cryostat displacement and stress response is small under the action of earthquake. According to the standards, EAST tokamak cryostat structure under the action of design seismic can meet the requirements of anti-seismic design intensity, and ensure the anti-seismic safety of equipment. (authors)

  17. Otimização da programação de cargas de forno em uma fábrica de fundição em aço-inox Optimizing the scheduling of furnace loadings in a inox-steel foundry

    Directory of Open Access Journals (Sweden)

    Raida de Jesus Silva

    2004-04-01

    Full Text Available Neste trabalho apresenta-se uma abordagem para otimizar a programação de cargas de forno em fundições de mercado de pequeno porte. Tal abordagem consiste, basicamente, em definir a programação dos fornos para produzir uma carteira de pedidos composta de diversas peças em ligas metálicas variadas, de maneira a maximizar a produtividade (ou a margem de contribuição ao lucro e satisfazer prazos de entrega e restrições de processo. O procedimento proposto é baseado na teoria dos problemas de corte e empacotamento; ele combina uma heurística construtiva gulosa com o clássico problema da mochila. Para validá-lo, um estudo de caso foi realizado numa fundição em aço-inox localizada em São Carlos, SP. Os resultados da simulação de duas semanas de produção da empresa mostraram que o procedimento é capaz de produzir soluções melhores do que as utilizadas pela empresa.This study presents an approach to optimize the scheduling of furnace loadings in small size foundries. The approach consists of determining a furnace scheduling to produce all ordered items in such a way as to maximize productivity (or profit contribution and satisfy due dates and process restraints. It is based on the theory of cutting and packing problems; it combines a greedy constructive heuristic and the classical knapsack problem. To validate the approach, a case study was developed in a inox-steel foundry located in São Carlos, SP. The results obtained simulating two weeks of the company production showed that the procedure is able to generate better solutions than the ones used by the company.

  18. East Asian Studies of Tropospheric Aerosols and their Impact on Regional Climate (EAST -AIRC): An overview

    Science.gov (United States)

    Zhangqing, Li; Li, C.; Chen, H.; Tsay, S.-C.; Holben, B.; Huang, J.; Li, B.; Maring, H.; Qian, Y.; Shi, G.; hide

    2011-01-01

    As the most populated region of the world, Asia is a major source of aerosols with potential large impact over vast downstream areas, Papers published in this special section describe the variety of aerosols observed in China and their effects and interactions with the regional climate as part of the East Asian Study of Tropospheric Aerosols and their Impact on Regional Climate (EAST-AIRC), The majority of the papers are based on analyses of observations made under three field projects, namely, the Atmospheric Radiation Measurements (ARM) Mobile Facility mission in China (AMF-China), the East Asian Study of Tropospheric Aerosols: An International Regional Experiment (EAST-AIRE), and the Atmospheric Aerosols of China and their Climate Effects (AACCE), The former two are U,S,-China collaborative projects, and the latter is a part of the China's National Basic Research program (or often referred to as "973 project"), Routine meteorological data of China are also employed in some studies, The wealth of general and speCIalized measurements lead to extensive and close-up investigations of the optical, physical, and chemical properties of anthropogenic, natural, and mixed aerosols; their sources, formation, and transport mechanisms; horizontal, vertical, and temporal variations; direct and indirect effects; and interactions with the East Asian monsoon system, Particular efforts are made to advance our understanding of the mixing and interaction between dust and anthropogenic pollutants during transport. Several modeling studies were carried out to simulate aerosol impact on radiation budget, temperature, precipitation, wind and atmospheric circulation, fog, etc, In addition, impacts of the Asian monsoon system on aerosol loading are also simulated.

  19. EAST machine assembly and its measurement system

    International Nuclear Information System (INIS)

    Wu, S.T.

    2005-01-01

    The EAST (HT-7U) superconducting tokamak consists of a superconducting poloidal field magnet system, a toroidal field magnet system, a vacuum vessel and in-vessel components, thermal shields and a cryostat vessel. The main parts of the machine have been delivered to ASIPP (Institute of Plasma Physics, Chinese Academy of Sciences) successionally from 2003. For its complicated constitution and precise requirement, a reasonable assembly procedure and measurement technique should be defined carefully. Before the assembly procedure, a reference frame has been set up with reference fiducial targets on the wall of the test hall by an industrial measurement system. After the torus of TF coils is formed, a new reference frame will be set up from the position of the TF torus. The vacuum vessel with all inner parts will be installed with reference of the new reference frame. The big size and mass of components, special configuration of the superconducting machine with tight installation tolerances of the HT-7U (EAST) machine result in complicated assembly procedure. The procedure had begun with the installation of the support frame and the base of cryostat vessel last year. In this paper, the requirements of the assembly precise for some key components of the machine are described. The reference frame for the assembly and maintenance is explained. The assembly procedure is introduced

  20. Middle East: New Balkans of the World?

    Directory of Open Access Journals (Sweden)

    Dr.Sc. Georgescu Stefan

    2012-12-01

    Full Text Available Middle East is a region whose geopolitical dynamics has many analogies with the role of the Balkans in the first half of the 19th century and up to the 3rd decade of the 20th century, namely a "Powder keg of Europe", defined in the same period as the "Eastern Issue".Moreover, Middle East is a region located at the junction of three continents: Europe, Asia and the Mediterranean Africa, and along with ancient Egypt is the cradle of Western civilization, providing for it political, economic, religious, scientific, military, intellectual and institutional models.Four millennia of civilization before Christian era did not pass without leaving a trace.Trade, currency, law, diplomacy, technology applied to works in time of war or peace, the profit based economy and the bureaucratized economy, popular and absolutist government, nationalist and universal spirit, tolerance and fanaticism – all these are not inventions of the modern world, but have their origins and methods of implementation, often even sophisticated methods, in this region.

  1. Energy privatization in the Middle East

    International Nuclear Information System (INIS)

    Tetreault, M.A.

    1997-01-01

    The issue of energy privatization in the Middle East was discussed with particular examples from Kuwait. The development of Kuwait's domestic political institutions is unique in the Arab Gulf which makes privatization more complicated than in other Middle Eastern countries. The major issue in Kuwait is whether foreign investors and domestic private investors will be allowed equity participation in oil and gas production projects. It was suggested that the answer depends on general assessments of national financial and state security interests and on individual case judgements respecting each potential partnership. Historically, one of the main reasons for nationalization of private investment in oil and gas in the Middle East was the desire of governments to increase state revenues. Nationalization permitted states to set prices and production levels themselves and to keep the difference between costs and prices instead of sharing it with corporate owners. However, nationalization is not without its problems as indicated by the difficulties encountered by governments in trying to make the the OPEC-managed hydrocarbon regime work. The three main reasons for the current willingness of Middle Eastern governments to consider re-admitting private companies as equity participants in their energy industries, namely market share and terms of access, interstate disputes, and desire to minimize corruption, were also discussed. It was suggested that these are strong arguments that support taking another look at privatization as a strategy that is in the long-term interest of Middle Eastern oil producing states. 19 refs

  2. Multinational uranium enrichment in the Middle East

    International Nuclear Information System (INIS)

    Ahmad, Ali; Salahieh, Sidra; Snyder, Ryan

    2017-01-01

    The Joint Comprehensive Plan of Action (JCPOA) agreed to by Iran and the P5+1 in July 2015 placed restrictions on Iran’s nuclear program while other Middle Eastern countries– Egypt, Jordan, Saudi Arabia, Turkey, and the United Arab Emirates–are planning to build their own nuclear power plants to meet increasing electricity demands. Although the JCPOA restricts Iran's uranium enrichment program for 10–15 years, Iran's neighbors may choose to develop their own national enrichment programs giving them a potential nuclear weapons capability. This paper argues that converting Iran's national enrichment program to a more proliferation-resistant multinational arrangement could offer significant economic benefits–reduced capital and operational costs–due to economies of scale and the utilization of more efficient enrichment technologies. In addition, the paper examines policy aspects related to financing, governance, and how multinational enrichment could fit into the political and security context of the Middle East. A multinational enrichment facility managed by regional and international partners would provide more assurance that it remains peaceful and could help build confidence between Iran and its neighbors to cooperate in managing other regional security challenges. - Highlights: • Freezing Iran's nuclear program is an opportunity to launch joint initiatives in ME. • A joint uranium enrichment program in the Middle East offers economic benefits. • Other benefits include improved nuclear security and transparency in the region.

  3. East Europe's energy trade takes new shape

    International Nuclear Information System (INIS)

    Movit, C.

    1991-01-01

    Often in the past, Western analysts of global energy demand have treated Eastern Europe as just part of a black box labeled Communist. Only the net flow of energy to the non-Communist world was of any consequence. The region, although primarily a major net importer of energy from the Soviet Union, was a very small net exporter of energy to non-Communist countries based Polish coal exports. Romanian refined petroleum product exports, and some minor exports of refined products by other East European countries. The political and economic configurations of Eastern Europe has changed dramatically over the past 2 years, however, and the way in which East European energy relationships are considered will have to change accordingly. With the sweeping transformation of these economies (for the most part, radically in the direction of a market orientation) and the breakup of their unique system of mutual trade, the patterns of energy production, consumption, and trade which have prevailed in the region during the post-war period will also change significantly. Forecasting the net-impact on energy demand in this region of offsetting trends due to economic reform (i.e., renewed economic dynamism vs. decreased energy intensity of aggregate economic output) is a very difficult task. Moreover, there are additional complications introduced by changes in the political system, such as the increased importance of environmental quality in the choice of fuel and production technology due to clearly enunciated concern of the popular political movements with these issues

  4. East coast gas - the big picture

    International Nuclear Information System (INIS)

    Drummond, K.J.

    1998-01-01

    The North American conventional gas resource base was reviewed and an explanation of how Canada's East coast fits into the overall picture was given. At 1996 year end, the total conventional ultimate natural gas resource base for North America was estimated to be 2,695 trillion cubic feet. The most important supply areas are Canada and the United States. Mexico and Alaska are expected to play only a minor role in the overall North American supply. Approximately half of the conventional gas estimated to exist in North America remains to be discovered. Only 78 per cent from the half that has been discovered has been produced, and only 22 per cent of it is remaining as reserves. Of the undiscovered natural gas resource, 38 per cent is in the frontier regions of Alaska and Canada. The growing importance of the East coast of North America as markets for natural gas was reviewed. The distribution of ultimate conventional marketable gas resources for Canada was described. The potential of the Western Canadian Sedimentary Basin (WCSB) and selected frontier areas were assessed. The report showed an undiscovered conventional marketable gas estimate of 122 trillion cubic feet for the WCSB and 107 trillion cubic feet for the Frontier areas. The two most significant areas of discovery in eastern Canada were considered to be the Hibernia oil field on the Grand Banks and the Venture gas field of the Scotian Shelf. 2 tabs., 7 figs

  5. East coast development overview : why now?

    International Nuclear Information System (INIS)

    Anderson, J.

    1998-01-01

    Progress achieved in developing East coast natural gas markets was discussed. Mobil, Shell, Imperial, Mosbacher and Nova Scotia Resources received the go-ahead for the Sable Offshore Energy Project last December. The owner companies created Sable Offshore Energy Inc. (SOE Inc.) for managing and operating the development. Mobil (which has 50 per cent of the total invested in the Sable offshore project) and their partners will spend an average of one million dollars per day in Nova Scotia over the next 22 months in order to ensure that they will deliver gas from the offshore site by late 1999. That is in addition to the 400 million dollars already spent by the consortium in the province of Nova Scotia. Job creation, of particular significance in the Atlantic provinces, is also expected to be a significant factor in lifting the GDP of Nova Scotia to three per cent in 1998. According to an estimate by the Bank of Nova Scotia, the Sable and pipeline projects alone will create more than 7,500 spin-off jobs. The five major factors which make eastern Canada development possible and economically attractive are: (1) resource potential, (2) technological advancements, (3) alliances, (4) market proximity, and (5) the rapidly expanding global market for natural gas. Each of these factors and how they impact on the East coast natural gas industry were discussed in some detail

  6. Filterscope diagnostic system on EAST tokamak

    International Nuclear Information System (INIS)

    Xu, Z.; Wu, Z.W.; Gao, W.; Zhang, L.; Huang, J.; Chen, Y.J.; Wu, C.R.; Zhang, P.F.

    2015-01-01

    Filterscope diagnostic system, which is designed for monitoring the line emission in fusion plasma has been widely used on fusion devices such as DIII-D, NSTX, CDX-U, KSTAR etc. On EAST (Experimental Advanced Superconducting Tokamak), a filterscope diagnostic system has been mounted to observe the line emission and visible bremsstrahlung emission in plasma from discharge campaign of 2014. It plays a crucial role in studying Edge Localized Modes (ELM) and H-mode, thanks to its high temporal resolution (0.005ms) and good spatial resolution (∼2cm). Furthermore, multi-channel signals at up to 200kHz sampling rates can be digitized simultaneously. The wavelength covers He II (468.5nm), Li I (670.8nm), Li II (548.3nm), C III (465.0nm), O II (441.5nm), Mo I (386.4nm), W I (400.9nm) and visible bremsstrahlung radiation at 538nm besides Dα (656.1nm) and Dγ (433.9nm) with the corresponding wavelength filters. The new developed filterscope system was operating during the EAST 2014 fall experimental campaign and several types ELMs has been observed. (author)

  7. The East Greenland rifted volcanic margin

    Directory of Open Access Journals (Sweden)

    C. Kent Brooks

    2011-12-01

    Full Text Available The Palaeogene North Atlantic Igneous Province is among the largest igneous provinces in the world and this review of the East Greenland sector includes large amounts of information amassed since previous reviews around 1990.The main area of igneous rocks extends from Kangerlussuaq (c. 67°N to Scoresby Sund (c. 70°N, where basalts extend over c. 65 000 km2, with a second area from Hold with Hope (c. 73°N to Shannon (c. 75°N. In addition, the Ocean Drilling Project penetrated basalt at five sites off South-East Greenland. Up to 7 km thickness of basaltic lavas have been stratigraphically and chemically described and their ages determined. A wide spectrum of intrusions are clustered around Kangerlussuaq, Kialeeq (c. 66°N and Mesters Vig (c. 72°N. Layered gabbros are numerous (e.g. the Skaergaard and Kap Edvard Holm intrusions, as are under- and oversaturated syenites, besides small amounts of nephelinite-derived products, such as the Gardiner complex (c. 69°N with carbonatites and silicate rocks rich in melilite, perovskite etc. Felsic extrusive rocks are sparse. A single, sanidine-bearing tuff found over an extensive area of the North Atlantic is thought to be sourced from the Gardiner complex.The province is famous for its coast-parallel dyke swarm, analogous to the sheeted dyke swarm of ophiolites, its associated coastal flexure, and many other dyke swarms, commonly related to central intrusive complexes as in Iceland. The dyke swarms provide time markers, tracers of magmatic evolution and evidence of extensional events. A set of dykes with harzburgite nodules gives unique insight into the Archaean subcontinental lithosphere.Radiometric dating indicates extrusion of huge volumes of basalt over a short time interval, but the overall life of the province was prolonged, beginning with basaltic magmas at c. 60 Ma and continuing to the quartz porphyry stock at Malmbjerg (c. 72°N at c. 26 Ma. Indeed, activity was renewed in the Miocene with

  8. Soccer: Moulding the Middle East and North Africa

    NARCIS (Netherlands)

    Dorsey, J.M.

    2016-01-01

    Nowhere in the world has sports in general and soccer in particular played such a key role in the development of a region than in the Middle East and North Africa. Yet, the nexus of sports, politics and society is one area that Middle East studies with few exceptions have ignored. Similarly, sports

  9. The first-step of EAST remote participation system

    Energy Technology Data Exchange (ETDEWEB)

    Sun, Xiaoyang, E-mail: xysun@ipp.ac.cn; Ji, Zhenshan; Wang, Feng; Li, Shi; Wang, Yong

    2016-11-15

    Highlights: • A new design for remote participation system for EAST tokamak is proposed. • Rich Internet Application (RIA) and NoSQL Database was select to implement the system. • Two kind of technique for accessing EPICS PV data remotely through Internet was proposed. - Abstract: The EAST Tokamak at Institute of Plasma Physics Chinese Academy of Sciences (CASIPP) is the first fully-superconducting Tokamak facility. International collaboration can improve the quality and impact of fusion research. It is a key feature for EAST research. During 2014 EAST campaign, more than 60 physicists and experts visited CASIPP and participated in EAST discharging experiment. With an increasing number of collaborations, remote participation becomes important as an economical and effective alternative to traditional way. This paper presents an overview of the first-step development work of the EAST Remote Participation System (EAST RPS). At current stage, the EAST RPS is focused on remote access to engineering data, NoSQL-based data archiving engine, message service and video service.

  10. East and Central African Journal of Surgery: Contact

    African Journals Online (AJOL)

    Principal Contact. Prof. Ignatius Kakande Editor-in-Chief Association of Surgeons of East Africa. East and Central African Journal of Surgery. P.O. Box 7051. Kampala. Uganda. Alternative email: igkakande@gmail.com. Phone: +256 772 501 745. Email: ecajs@gmail.com ...

  11. The East European Press and Three-Mile Island.

    Science.gov (United States)

    Johnson, Owen V.

    This report of the investigation into East European newspaper treatment of the accident at Pennsylvania's Three Mile Island nuclear power plant in the spring of 1979 focuses on the Czech and Slovak media, particularly on the Slovak Communist Party's daily newspaper, "Pravda." The response of the media of other East European countries to…

  12. Far East Asia | Page 67 | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Far East Asia. Extrême-Orient. Read more about Environmental Degradation, Social Marginalization and the Dynamics of Vulnerability in the Earthquake of October 2005 (Pakistan). Language English. Read more about Promoting Trade in Services in the Middle East and North Africa : Pilot Project. Language English.

  13. Crowdfunding in Emerging Markets : Lessons from East African Startups

    OpenAIRE

    World Bank Group

    2015-01-01

    The purpose of this paper is to capture lessons learned from East African entrepreneurs who were some of crowdfunding’s first adopters. Their experiences can serve as a practical guide for entrepreneurs looking to more effectively utilize crowdfunding across all emerging markets. In order to gather this data, the World Bank conducted interviews with a number of East African technology entr...

  14. Design and thermal-hydraulic calculation for EAST PFCs' baking

    International Nuclear Information System (INIS)

    Wan Xiaogang; Yao Damao

    2006-01-01

    According to the vacuum requirements for fusion in a tokamak device, the authors adopted a kind of gas flow baking technique in EAST. This paper presented the sketch design for EAST PFCs' baking, selected the specifications for the working gas. Calculated the hydraulic and thermal conditions in PFCs under baking, and simulated the results. (authors)

  15. Measuring Entrepreneurial Activity in the Middle East and North Africa

    International Development Research Centre (IDRC) Digital Library (Canada)

    Total funding. CA$ 678,500. Country(s). Middle East, North of Sahara, South of Sahara, Central Asia, Far East Asia, South Asia. Project Leader. Dr. Mohamed Derrabi. Institution. Al Akhawayn University. Institution Country. Morocco. Institution Website. http://www.aui.ma. Project Leader. Abedou Abderrahamne. Institution.

  16. Elders Point East Marsh Island Restoration Monitoring Data Analysis

    Science.gov (United States)

    2017-09-21

    accounting for more than 90% of the measured biomass on average, indicative of a well-established marsh (Figure 12). For Elders East the data indicated...61 3.3 Other Biological and Physical Measures ...Figure 9. Growth measurements at Elders East and JoCo Marsh. ....................................................... 20 Figure 10. Stem survival at

  17. East Africa Evaluation Hub - Institute of Rural Reconstruction (IIRR ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Outcome Mapping is a planning, monitoring and evaluation methodology developed by IDRC and its partners. There is an active global community of Outcome Mapping users, but few of them are in East Africa. A survey of evaluation experts and development organizations in East Africa showed some familiarity with and ...

  18. Investment, stability and the politics of Middle-East embargoes

    International Nuclear Information System (INIS)

    Hollis, R.

    1996-01-01

    This paper reviews the political situation in the Middle East and considers the current level of energy investment in the region. The factors affecting the stability of countries in the Middle East are examined, and the politics of western embargoes is explored. (author)

  19. Transferring the Malaria Epidemic Prediction Model to Users in East ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Transferring the Malaria Epidemic Prediction Model to Users in East Africa. In the highlands of East Africa, epidemic malaria is an emerging climate-related hazard that urgently needs addressing. Malaria incidence increased by 337% during the 1987 epidemic in Rwanda. In Tanzania, Uganda and Kenya, malaria incidence ...

  20. Sef-interest vs altruism in East Asia's development aid

    DEFF Research Database (Denmark)

    Müller, Anders Riel

    2013-01-01

    Criticism of East Asia’s alleged self-interest-led development aid can also be applied to Western donors. This may teach us lessons about our own history.......Criticism of East Asia’s alleged self-interest-led development aid can also be applied to Western donors. This may teach us lessons about our own history....

  1. Looking East: Yin and Yang of an Academic Exchange

    Science.gov (United States)

    La Roche, Claire Reeves

    2011-01-01

    Intended as a brief guide to the cultural differences associated with an East-West academic exchange, this paper discusses customs and cultural norms likely to be encountered. Chinese economic growth has been accompanied by rapidly increasing East-West study abroad opportunities. Over the past decade, China has sent more students to study abroad…

  2. The first-step of EAST remote participation system

    International Nuclear Information System (INIS)

    Sun, Xiaoyang; Ji, Zhenshan; Wang, Feng; Li, Shi; Wang, Yong

    2016-01-01

    Highlights: • A new design for remote participation system for EAST tokamak is proposed. • Rich Internet Application (RIA) and NoSQL Database was select to implement the system. • Two kind of technique for accessing EPICS PV data remotely through Internet was proposed. - Abstract: The EAST Tokamak at Institute of Plasma Physics Chinese Academy of Sciences (CASIPP) is the first fully-superconducting Tokamak facility. International collaboration can improve the quality and impact of fusion research. It is a key feature for EAST research. During 2014 EAST campaign, more than 60 physicists and experts visited CASIPP and participated in EAST discharging experiment. With an increasing number of collaborations, remote participation becomes important as an economical and effective alternative to traditional way. This paper presents an overview of the first-step development work of the EAST Remote Participation System (EAST RPS). At current stage, the EAST RPS is focused on remote access to engineering data, NoSQL-based data archiving engine, message service and video service.

  3. The Business of Politics Commerce, and Culture in East Asia

    DEFF Research Database (Denmark)

    Ooi, Can-Seng

    2016-01-01

    Review of: "Cultural Policies in East Asia: Dynamics Between the State, Arts and Creative Industries". Edited by Hye-Kyung Lee and Lorraine Lim. Basingstoke: Palgrave, Macmillan, 2014. 229 pp.......Review of: "Cultural Policies in East Asia: Dynamics Between the State, Arts and Creative Industries". Edited by Hye-Kyung Lee and Lorraine Lim. Basingstoke: Palgrave, Macmillan, 2014. 229 pp....

  4. Recent progress of the ECE diagnostics on EAST

    International Nuclear Information System (INIS)

    Liu, Y.; Ling, B.L.; Han, X.

    2013-01-01

    On EAST, a 32-channel radiometer system with wider frequency range and better spatial resolution has been commissioned in 2012, and a Michelson interferometer system from JET was relocated very recently. These systems together with the systems we already have, satisfy the requirement of the electron cyclotron emission measurements on EAST for a wide range of toroidal magnetic field. (author)

  5. Absolute intensity calibration for ECE measurements on EAST

    International Nuclear Information System (INIS)

    Liu Yong; Liu Xiang; Zhao Hailin

    2014-01-01

    In this proceeding, the results of the in-situ absolute intensity calibration for ECE measurements on EAST are presented. A 32-channel heterodyne radiometer system and a Michelson interferometer on EAST have been calibrated independently, and preliminary results from plasma operation indicate a good agreement between the electron temperature profiles obtained with different systems. (author)

  6. Journal of East African Natural History: Editorial Policies

    African Journals Online (AJOL)

    Focus and Scope. The Journal of East African Natural History is published jointly by the East Africa Natural History Society and the National Museums of Kenya. The Journal publishes papers and notes in the field of natural history, broadly defined as the study of organisms in their natural state, relevant to the eastern African ...

  7. Management of Water Demand in Africa and the Middle East ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Management of Water Demand in Africa and the Middle East : Current Practices and Future Needs. Couverture du livre Management of Water Demand in Africa and the Middle East : Current Practices. Directeur(s) : David B. Brooks, Eglal Rached et Maurice Saade. Maison(s) d'édition : CRDI. 1 janvier 1997. ISBN : Épuisé.

  8. Management of Water Demand in Africa and the Middle East ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    1997-01-01

    Management of Water Demand in Africa and the Middle East : Current Practices and Future Needs. Couverture du livre Management of Water Demand in Africa and the Middle East : Current Practices. Editor(s):. David B. Brooks, Eglal Rached et Maurice Saade. Publisher(s):. CRDI. January 1, 1997. ISBN: Épuisé. 78 pages.

  9. Far East Asia | Page 185 | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    In Multinationals and East Asian Integration, leading Asian economists examine the role of foreign private-sector firms, especially from Japan and the United States, in the recent and rapid economic growth and integration in East Asia. With examples from China, Hong Kong, Indonesia, Malaysia, the Philippines, Singapore, ...

  10. Far East Asia | Page 184 | IDRC - International Development ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    In Multinationals and East Asian Integration, leading Asian economists examine the role of foreign private-sector firms, especially from Japan and the United States, in the recent and rapid economic growth and integration in East Asia. With examples from China, Hong Kong, Indonesia, Malaysia, the Philippines, Singapore, ...

  11. Language Education Policy and Practice in East and Southeast Asia

    Science.gov (United States)

    Kirkpatrick, Andy; Liddicoat, Anthony J.

    2017-01-01

    East and Southeast Asia represents a linguistically and culturally diverse region. For example, more than 700 languages are spoken in Indonesia alone. It is against this backdrop of diversity that the ten countries that comprise Association of South East Asian Nations (ASEAN) have recently signed the ASEAN Charter which, while calling for respect…

  12. Toroidal charge exchange recombination spectroscopy on EAST

    Energy Technology Data Exchange (ETDEWEB)

    Ye, Minyou, E-mail: yemy@ustc.edu.cn [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 (China); Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Li, Yingying [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Yu, Yi [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 (China); Shi, Yuejiang [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 (China); WCI for Fusion Theory, National Fusion Research Institute, 52 Eoeun-Dong, Yusung-Gu, Daejeon 305-333 (Korea, Republic of); Lyu, Bo; Fu, Jia [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); Du, Xuewei; Yin, Xianghui; Zhang, Yi; Wang, Qiuping [School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 (China); Wan, Baonian [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei, Anhui 230031 (China); School of Nuclear Science and Technology, University of Science and Technology of China, Hefei, Anhui 230026 (China)

    2015-10-15

    A toroidal charge exchange recombination spectroscopy (CXRS) diagnostic, on the basis of a heating neutral beam injector (NBI), is constructed on EAST tokamak. Simulation of Spectra (SOS) code is used to design and evaluate the diagnostic performance. 30 spatial channels work simultaneously in recent experiment, which covers a radial region from 1.55 m to 2.30 m in the cross section. The CXRS has a radial resolution of 1–3.5 cm from core to edge. The acquisition time is typically 10 ms, limited by the poor photon statistics. The diagnostic can observe not only the normal C{sup 5+} emission line at 529.1 nm but also any interested wavelength in the range of 400–700 nm. In this work, a brief overview on the R&D and the instrument performance for the toroidal CXRS diagnostic is described, together with first results.

  13. Poppy tea drinking in East Anglia.

    Science.gov (United States)

    London, M; O'Regan, T; Aust, P; Stockford, A

    1990-10-01

    Poppy tea drinking was a widespread traditional practice in the Fenlands of East Anglia during the nineteenth century. The subsequent social changes which led to greater integration of the area with the rest of the country may have contributed to a decline in the practice. In recent years poppy tea drinking has been revived within the illicit drug using community and a survey using a self-report questionnaire was carried out among patients attending the Cambridge Drug Dependency Unit. Forty-three patients admitted to drinking poppy tea, usually during the summer months and on an intermittent basis. The potency of the infusion varied and was unpredictable but in general was low. Although poisoning from herbicides and pesticides was seen as the main risk, it is in the main perceived by drug users as a harmless secondary activity existing alongside the more regular and more potent drugs of misuse.

  14. Middle East natural gas - getting it to markets

    International Nuclear Information System (INIS)

    Skinner, R.

    1996-01-01

    Middle East gas reserves, production, and consumption were presented graphically, along with the demand for 'piped' or liquefied natural gas in the Middle East itself, in Asia and in Europe. The European gas market outlook was examined, taking into account economic growth, EEC restructuring, crude oil prices and their effects on net-backs, deregulation and competitive grid-based energy, upstream and midstream investments under conditions of price uncertainty, and environmental and social influences. Middle East pipeline proposals (17 projects) for a total of 34,943 kilometres of pipeline, were reviewed. The general conclusion was that (1) the Middle East has lots of gas, (2) both Asia and Europe will be substantial markets for Middle East LNG despite the 'tyranny of distance', and (3) pipelines to these markets will be built in the longer-term. tabs., figs

  15. Potential of Fishing Port Development in the East Java

    Science.gov (United States)

    Rosana, N.; Prasita, V. D.

    2018-03-01

    The development of fishing ports in East Java is one of efforts to increase the province revenue, develop the fishing industry and to improve the welfare of fishermen. Profile of capture fisheries in East Java should be provide information that can be developed based on priorities and types of resources. The purpose of this study was to determine several districts in East Java which is a priority for the development of fishing ports based on the potential that exists. The method used is descriptive and spatial analysis in order to obtain an overview of the districts in East Java that has the potential to be developed. Results of the study is the districts in East Java are priorities for the development of fishing ports based on aspects related to the fishery is Banyuwangi, Trenggalek and Jember.

  16. Biogeochemistry of the Ballarat East goldfield

    International Nuclear Information System (INIS)

    Stott, J.; Arne, D.; Waldron, H.

    1998-01-01

    The gold deposits along the crest of the Whitehorse Range were extensively worked last century, and the area was revegetated during the 1930s with Monterey Pine (P. radiata). P. Radiata of different ages were sampled at 25m intervals along two east-west traverses roughly perpendicular to the strike of the Ballarat East field. Sampling occurred during the winter of 1995 following heavy rains. Blackwood (Acacia melanoxylon) and Chinese scrub (Cassinia aculeata) were also sampled for comparative purposes. A third traverse through a belt of remnant eucalyptus (E. obliqua, E. dives, and E. macrorhyncha) was sampled to the south of the pine plantation in 1996. These samples were washed in de-ionised water. Sample material included either leaves or needles, the tips of twigs, and outer bark. The samples were dried, pulverized and analysed using instrumental neutron activation at Lucas Heights, NSW. Gold and As from Cassinia leaves and twigs, and Eucalyptus bark show a good correlation with extensions of known mineralized trends inferred from aerial photographs, as do Ce, Cr, La, Sm, Sc and Th. Samples of P. radiata needles and bark show only a moderate correlation with mineralized trends for Au and As. Repeat sampling to determine sampling variance has revealed probable contamination of Eucalyptus outer bark by dust. Sequential washing experiments indicate that the dust is difficult to remove from fibrous outer bark. Therefore, while application of biogeochemistry to exploration in the central Victorian Goldfields appears feasible, caution must be exercised in the interpretation of data from outer bark for some Eucalyptus species

  17. Cleveland Dam East Abutment : seepage control project

    Energy Technology Data Exchange (ETDEWEB)

    Huber, F.; Siu, D. [Greater Vancouver Regional District, Burnaby, BC (Canada); Ahlfield, S.; Singh, N. [Klohn Crippen Consultants Ltd., Vancouver, BC (Canada)

    2004-09-01

    North Vancouver's 91 meter high Cleveland Dam was built in the 1950s in a deep bedrock canyon to provide a reservoir for potable water to 18 municipalities. Flow in the concrete gravity dam is controlled by a gated spillway, 2 mid-level outlets and intakes and 2 low-level outlets. This paper describes the seepage control measures that were taken at the time of construction as well as the additional measures that were taken post construction to control piezometric levels, seepage and piping and slope instability in the East Abutment. At the time of construction, a till blanket was used to cover the upstream reservoir slope for 200 meters upstream of the dam. A single line grout curtain was used through the overburden from ground surface to bedrock for a distance of 166 meters from the dam to the East Abutment. Since construction, the safety of the dam has been compromised through changes in piezometric pressure, seepage and soil loss. Klohn Crippen Consultants designed a unique seepage control measure to address the instability risk. The project involved excavating 300,000 cubic meters of soil to form a stable slope and construction bench. A vertical wall was constructed to block seepage. The existing seepage control blanket was also extended by 260 meters. The social, environmental and technical issues that were encountered during the rehabilitation project are also discussed. The blanket extension construction has met design requirements and the abutment materials that are most susceptible to internal erosion have been covered by non-erodible blanket materials such as plastic and roller-compacted concrete (RCC). The project was completed on schedule and within budget and has greatly improved the long-term stability of the dam and public safety. 2 refs., 8 figs.

  18. East African discourses on khat and sex.

    Science.gov (United States)

    Beckerleg, Susan

    2010-12-01

    The study aims to review and analyse the varied East African discourses on the effects of khat use on libido, fertility, transmission of HIV, prostitution and rape. The data were gathered between 2004 and 2009 in Kenya and Uganda. Between 2004 and 2005 across Kenya and Uganda a broad survey approach was adopted, involving identification of and travel to production areas, interviews with producers and consumers in rural and urban settings. In addition, a survey of 300 Ugandan consumers was carried out in late 2004. Between 2007 and 2009, an in-depth study of khat production, trade and consumption was conducted in Uganda. This study also employed a mixture of methods, including key informant interviews participant-observation and a questionnaire survey administered to 210 khat consumers. Khat is associated, by consumers and its detractors alike, with changes in libido and sexual performance. Although there is no evidence to support their claims, detractors of khat use argue that khat causes sexual violence, causes women to enter sex work, and that chewing causes the spread of sexually transmitted diseases, including the HIV virus. In East Africa the discourse on khat and sex has led to consumption of the substances being associated by many people with uncontrolled sexual behaviour. There is no evidence that khat use fuels promiscuity, commercial sex, sexually transmitted diseases or rape. The current discourse on khat and sex touches on all these topics. Local religious and political leaders invoke khat use as a cause of what they argue is a breakdown of morals and social order. In Kenya and Uganda it is women khat consumers who are seen as sexually uncontrolled. In Uganda, the argument is extended even to men: with male khat chewers labelled as prone to commit rape. Copyright © 2010 Elsevier Ireland Ltd. All rights reserved.

  19. Biogeochemistry of the Ballarat East goldfield

    Energy Technology Data Exchange (ETDEWEB)

    Stott, J.; Arne, D. [University of Ballarat, VIC (Australia). Minerals Industry Research Institute]|[Posgold Ltd, Tennant Creek, NT (Australia); Waldron, H. [Becquerel Laboratories, Lucas Heights, NSW (Australia)

    1998-12-31

    The gold deposits along the crest of the Whitehorse Range were extensively worked last century, and the area was revegetated during the 1930s with Monterey Pine (P. radiata). P. Radiata of different ages were sampled at 25m intervals along two east-west traverses roughly perpendicular to the strike of the Ballarat East field. Sampling occurred during the winter of 1995 following heavy rains. Blackwood (Acacia melanoxylon) and Chinese scrub (Cassinia aculeata) were also sampled for comparative purposes. A third traverse through a belt of remnant eucalyptus (E. obliqua, E. dives, and E. macrorhyncha) was sampled to the south of the pine plantation in 1996. These samples were washed in de-ionised water. Sample material included either leaves or needles, the tips of twigs, and outer bark. The samples were dried, pulverized and analysed using instrumental neutron activation at Lucas Heights, NSW. Gold and As from Cassinia leaves and twigs, and Eucalyptus bark show a good correlation with extensions of known mineralized trends inferred from aerial photographs, as do Ce, Cr, La, Sm, Sc and Th. Samples of P. radiata needles and bark show only a moderate correlation with mineralized trends for Au and As. Repeat sampling to determine sampling variance has revealed probable contamination of Eucalyptus outer bark by dust. Sequential washing experiments indicate that the dust is difficult to remove from fibrous outer bark. Therefore, while application of biogeochemistry to exploration in the central Victorian Goldfields appears feasible, caution must be exercised in the interpretation of data from outer bark for some Eucalyptus species

  20. Crustal evolution in north-east and east Africa from model Nd ages

    International Nuclear Information System (INIS)

    Harris, N.B.W.; Hawkesworth, C.J.; Ries, A.C.

    1984-01-01

    The authors present the results of an Nd isotope study on the major rock units of the Pan-African (1,100-500 Myr BP) terrane. Charnockites from Jabel Uweinat, a basement inlier at the junction of Egypt, Libya and the Sudan, yield middle Archaean model Nd ages, whilst model ages of < 1,200 Myr have been obtained in a belt from the Eastern Desert of Egypt to north-west Kenya. Overall, the Pan-African rocks from north-east and east Africa and those from the Damara of Namibia exhibit a wide range of epsilonsub(Nd)(T) from +7.5 to -18.0 which reflects regional changes in tectonic style and is not readily reconciled with simple models for the evolution of average continental crust. (author)

  1. Multiple Sclerosis Epidemiology in East Asia, South East Asia and South Asia: A Systematic Review.

    Science.gov (United States)

    Eskandarieh, Sharareh; Heydarpour, Pouria; Minagar, Alireza; Pourmand, Shadi; Sahraian, Mohammad Ali

    2016-01-01

    Multiple sclerosis (MS) is one of the most common chronic immune-mediated diseases of the human central nervous system and an important cause of non-traumatic neurologic disability among young population in several countries. Recent reports from East Asia, South East Asia and South Asia have proposed a low to moderate prevalence of MS in these countries. A literature review search was carried out in December 2014 in Medline, Embase, Scopus and Cochrane library to recover original population-based studies on MS epidemiology in East Asia, South East Asia and South Asia countries published between January 1, 1950 and December 30, 2014. We intended search strategies using the key words: multiple sclerosis, prevalence, incidence and epidemiology. Based on our inclusion criteria, 68 epidemiologic studies were included in this systematic review. The most extensively used diagnostic criteria in the studies were McDonald's criteria. Most studies were performed in a multi-center hospital setting. The female to male ratio varied and ranged from 0.7 in India to 9.0 in China. The mean age at disease onset ranged from the lowest age of 25.3 in Iran to the highest age of 46.4 in China. MS prevalence ranged from 0.77 in 100,000 populations in Hong Kong (1999) to 85.80 in 100,000 in Iran (2013). Advances in MS registries around the globe allow nationwide population-based studies and will allow worldly comparisons between the prevalence and incidence in different regions that are provided to monitor estimation. © 2016 S. Karger AG, Basel.

  2. The role of the East Asian active margin in widespread extensional and strike-slip deformation in East Asia

    NARCIS (Netherlands)

    Schellart, Wouter P.; Lister, G. S.

    2005-01-01

    East Asia is a region of widespread deformation, dominated by normal and strike-slip faults. Deformation has been interpreted to result from extrusion tectonics related to the India-Eurasia collision, which started in the Early Eocene. In East and SE China, however, deformation started earlier than

  3. Transitional processes and the role of cities in east and South-East Europe

    Directory of Open Access Journals (Sweden)

    Stojkov Borislav

    2014-01-01

    Full Text Available The cities of Eastern and South East Europe, passing through dynamic and uncertain processes of social, economic and political transition, are being confronted with serious challenges in relation to more stabilized cities of Central and, especially, Western Europe. The former policy of centralization is faced with political, administrative and economic changes, as well as with aspirations towards decentralization, regionalization and polycentrism. The confronted tendencies still dominantly influence to the level of Eastern and South East cities' competitiveness. This urgently asks for orientation towards functional positioning of cities within wider metropolitan and regional frameworks. Another crucial orientation is presented by initial tendencies of metropolitan areas linking or networking in wider regional context. Both tendencies indicate the crucial problem of city governance quality level, according to contemporary criteria instead classical and hierarchical model of executing governmental power. Some examples of cities in Eastern and South East Europe are presented in the article, as well as of some cities in Central Europe where initial phase of transition has been completed.

  4. Cross-national differences in the holistic use of traditional East Asian medicine in East Asia.

    Science.gov (United States)

    Shim, Jae-Mahn; Kim, Jibum

    2016-12-23

    Complementary and alternative medicine (CAM) has been one of the popular strategies for health promotion. Traditional East Asian medicine (TEAM) is one of the most popular CAM practices in the world and there are suggestions that its holistic utilization is important for users to gain its effects for health promotion. In this context, this study investigates the extent to which TEAM users in East Asian countries utilize various modalities of TEAM holistically. It provides a model that explains cross-national differences in the extent of the holistic use of TEAM between China, Japan, Korea and Taiwan. Using the 2010 East Asian Social Survey, regression models specify the relationship between the holistic use of TEAM and the geographical location (country). The presence of TEAM doctors who hold the comprehensive and exclusive practice rights over TEAM is found to be conducive to the holistic utilization of various TEAM modalities. Thus, Taiwanese and Koreans use TEAM more holistically than Chinese and even more so than Japanese. The result suggests that the manner in which TEAM is institutionalized affect the extent to which TEAM users utilize various TEAM modalities together and potentially the health promotion effects of TEAM. © The Author 2016. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  5. Proceedings of the French Senate conference 'Going Nuclear in the Middle East - In search of an European Middle East policy'

    International Nuclear Information System (INIS)

    Larcher, G.; De Rohan, J.; Malley, R.; Francois-Poncet, J.; Boroumand, L.; Cordesman, A.H.; Alani, M.; Hourcade, B.; Cerisier-ben Guiga, M.; Shihabi, M.; Singh, M.; Siegman, H.; Aubin De La Messuziere, Y.; Boillon, B.; Yasseen, F.; Barzani, M.; Chouet, A.; Filiu, J.P.; Heisbourg, F.; Giuliani, J.D.; Asseburg, M.; Spencer, C.; Solana Madagaria, J.

    2010-01-01

    The Middle East today is quite clearly one of the global hotspots of the world. It is also a big challenge for the international community. The interests are due to geography, history, economics and also to the fact that what takes place in the Middle East is important for the security of rest of the world. These two days of conference organised by the French Senate took stock of the Middle East question through 6 round tables dealing with: 1 - General overview Nuclear Islam in the Middle East; 2 - How likely is a successful dialogue with Iran? 3 - What Future for the Palestinian People? 4 - 2010, A Renaissance for Iraq? 5 - The Latest on Al Qaeda? 6 - In search of a European Union Policy for the Middle East. This document gathers the talks of the different experts and the questions and answers from the participants. (J.S.)

  6. Russia And East Asia: New Opportunities And Challenges

    Directory of Open Access Journals (Sweden)

    Anna A. Kireeva

    2014-01-01

    Full Text Available The article focuses on major dimensions, achievements, challenges and prospects of relations between Russia and East Asia. Strategic importance of the region is shaped by East Asia's increasing role in world politics and economy as well as by its appeal for Russia's modernization agenda. Russia's great power status rests upon the effectiveness of its East Asian policy and development model of Siberia and the Russian Far East. Russia's positions in East Asia have improved substantially over the 2000s. However, its involvement in regional economic interaction is still insignificant and Russia cannot be regarded as a full-fledged regional player in this domain. Russian-Chinese strategic partnership has been the axis of Russia's East Asian foreign policy, though overdependence on China threatens Russia's independent policy in the region and encourages Russia to search for ways to diversify its ties. Russia's national interests reside in multivector policy, aimed at developing substantive relations not only with China but also with Japan, South Korea, ASEAN (Vietnam in the first place and India along with Russia's involvement in the resolution of Korean nuclear crisis. The rise of China and the US counter-offensive have resulted in a changing strategic environment in East Asia. A need for balancing between the US and China has brought about ASEAN countries' desire to welcome Russia as a "balancer" or an "honest player" in the region. It corresponds with Russia's course on playing a greater role in regional cooperation and integration. Russia's improving ties in political, economic, energy and security dimensions have the potential to contribute to the stability of the emerging polycentric regional order in East Asia and development of Russia's regions of Siberia and the Far East.

  7. RUSSIA AND EAST ASIA: NEW OPPORTUNITIES AND CHALLENGES

    Directory of Open Access Journals (Sweden)

    Anna A. Kireeva

    2014-01-01

    Full Text Available The article focuses on major dimensions, achievements, challenges and prospects of relations between Russia and East Asia. Strategic importance of the region is shaped by East Asia's increasing role in world politics and economy as well as by its appeal for Russia's modernization agenda. Russia's great power status rests upon the effectiveness of its East Asian policy and development model of Siberia and the Russian Far East. Russia's positions in East Asia have improved substantially over the 2000s. However, its involvement in regional economic interaction is still insignificant and Russia cannot be regarded as a full-fledged regional player in this domain. Russian-Chinese strategic partnership has been the axis of Russia's East Asian foreign policy, though overdependence on China threatens Russia's independent policy in the region and encourages Russia to search for ways to diversify its ties. Russia's national interests reside in multivector policy, aimed at developing substantive relations not only with China but also with Japan, South Korea, ASEAN (Vietnam in the first place and India along with Russia's involvement in the resolution of Korean nuclear crisis. The rise of China and the US counter-offensive have resulted in a changing strategic environment in East Asia. A need for balancing between the US and China has brought about ASEAN countries' desire to welcome Russia as a "balancer" or an "honest player" in the region. It corresponds with Russia's course on playing a greater role in regional cooperation and integration. Russia's improving ties in political, economic, energy and security dimensions have the potential to contribute to the stability of the emerging polycentric regional order in East Asia and development of Russia's regions of Siberia and the Far East.

  8. Trade Liberalization between Russia and East Asian Countries

    Directory of Open Access Journals (Sweden)

    Dmitriy Aleksandrovich Izotov

    2015-12-01

    Full Text Available Based on the international statistics data the author estimates effects of trade liberalization between Russia and East Asian countries. The prospective niche markets in mutual trade and the impact of trade liberalization on the national economies were identified. Using a partial equilibrium model the author indicates the following positive trade effects for Russia and East Asia: trade creation effect prevails over trade diversion effect; general welfare and mutual trade of the countries tend to increase. The Russian economy has positive trade effects with all the East Asian countries, with the highest scale in the case of Sino-Russian trade. At the same time trade liberalization has following some costs for the Russian economy: a the growing role of imports, mostly from China, compared to Russian exports; b reduction of tariff revenues, which are four times higher for Russia, compared to East Asian countries; c continued negative trade balance with the East Asian countries. The evaluation shows that the increase of Russian exports to East Asian countries is feasible only for certain commodity groups which determine marketable niches of specific East Asian countries; at the same time, Russia can import from East Asia a huge range of commodity groups. The study reveals that reduction in tariff measures and non- tariff restrictions will not lead to a massive increase in Russian exports and changing in its trade and geographical structure. On the basis of prolongation of short-term trends the author identifies long-term challenges and opportunities for the Russian economy from trade liberalization with East Asian countries. According to the estimation results, the author suggests that in the current environment of global trade liberalization the tariff measures become less significant as a tool for redistribution of commodity flows

  9. The late Cainozoic East Antarctic ice sheet

    International Nuclear Information System (INIS)

    Colhoun, E.A.

    1999-01-01

    A review, mainly of East Antarctic late Cainozoic (post 40 Ma) geological and geomorphological evidence, supports the hypothesis of the continuous presence of an ice sheet, of about the present size, since the late Miocene. Evidence is presented and the view advanced that, during the late Wisconsin maximum of isotope stage 2, ice was not nearly as thick or extensive over the continental shelf as required by the model of 'maximum' Antarctic glaciation. Some of the factors influencing the contribution of Antarctica to post-glacial sea-level rise are discussed. It is considered that Antarctica's contribution was probably considerably less than previously estimated. The dating of marine and freshwater sequences in the Vestfold and Bunger Hills is consistent with deglaciation around the Pleistocene Holocene boundary, after the Late Wisconsin maximum. A date of ∼25 ka BP from permafrost in the Larsemann Hills means that either the Larsemann Hills were not glaciated during the Late Wisconsin or the ice failed to erode much of the permafrost surface. The degree of weathering of rock and glacial drifts in the Vestfold, Larsemann and Bunger Hills suggests a long time for formation, perhaps considerably longer than indicated by the dated marine and freshwater sediment sequences. Cosmogenic isotope dating in the Vestfold Hills has provided equivocal ages for deglaciation. While the results could indicate deglaciation before 80 ka BP, they do not confirm such early deglaciation. If the ice cover was thin and failed to remove the previous rock exposure profile, then the assays could predate the last ice advance. Weathered iron crust fragments in the till suggest little erosion. The raised beaches of the oases are Holocene. Assuming they have been produced by post Late Wisconsin isostatic uplift and by the Holocene transgression, calculations show that the Antarctic continental ice sheet could not have been more than ∼500 m thicker in the inner shelf-coastal zone. The

  10. West-East migration in Germany since 1990

    OpenAIRE

    Beck, Grit

    2011-01-01

    Not only did 2.5 million people migrate from East Germany to West Germany between 1991 and 2006, 1.5 million people also moved from West to East Germany. This counter-current movement took placed largely unnoticed by the public and researchers alike. This paper uses both quantitative and qualitative data to first of all examine how the population structure in the New Länder has changed as a result of interregional migration between Länder in East and West Germany. It goes on to study the moti...

  11. Hopeful Chungnam Of The Miracle In The East Sea

    International Nuclear Information System (INIS)

    2008-07-01

    This reports Herbei spirit oil spill incident and overcoming the accident, which includes congratulatory address and the reason of publishing, summary of the Herbei spirit oil spill incident, starting the oil spill, spreading oil and restoration, trouble of creature ecology and fishing industry, the worst pollution and effort to restore and to prevent, public sentiment and executive measurement, volunteer work for prevention, donation, hopeful wave in the east sea, new jump for the clean east sea, report of passion on oil spill incident and culture tour cluster of Chungnam east sea.

  12. Operational region and sawteeth oscillation in the EAST tokamak

    International Nuclear Information System (INIS)

    Liu, H Q; Gao, X; Zhao, J Y; Hu, L Q; Jie, Y X; Ling, B L; Xu, Q; Ti, A; Ming, T F; Yang, Y; Wu, Z W; Wang, J; Xu, G S; Gao, W; Zhong, G Q; Zang, Q; Shi, Y J; Shen, B; Zhou, Q; Li, Y D; Gong, X Z; Hu, J S; Sun, Y W; Zhao, Y P; Luo, J R; Mao, J S; Weng, P D; Wan, Y X; Zhang, X D; Wan, B N; Li, J

    2007-01-01

    The first plasma discharges were successfully achieved on the experimental advanced superconducting tokamak (EAST) in 2006. The sawteeth behaviours were observed by means of soft x-ray diagnostics and ECE signals in the EAST. The displacement and radius of the q = 1 surface was studied and compared with the result of equilibrium calculation. The density sawtooth oscillation was also observed by the HCN laser interferometer diagnostics. The structure of the EAST operational region was studied in detail. Plasma performance was obviously improved by the boronization and wall conditioning. It was observed that lower q a and a wider stable operating region is extended by the GDC boronization

  13. Hopeful Chungnam Of The Miracle In The East Sea

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2008-07-15

    This reports Herbei spirit oil spill incident and overcoming the accident, which includes congratulatory address and the reason of publishing, summary of the Herbei spirit oil spill incident, starting the oil spill, spreading oil and restoration, trouble of creature ecology and fishing industry, the worst pollution and effort to restore and to prevent, public sentiment and executive measurement, volunteer work for prevention, donation, hopeful wave in the east sea, new jump for the clean east sea, report of passion on oil spill incident and culture tour cluster of Chungnam east sea.

  14. Variations of Terrestrial Net Primary Productivity in East Asia

    Directory of Open Access Journals (Sweden)

    Fangmin Zhang

    2012-01-01

    Full Text Available Due to the heterogeneity and complexity of terrestrial ecosystems of East Asia, a better understanding of relationships between climate change and net primary productivity (NPP distribution is important to predict future carbon dynamics. The objective of this study is to analyze the temporal-spatial patterns of NPP in East Asia (10°S - 55°N, 60 - 155°E from 1982 to 2006 using the process-based Boreal Ecosystem Productivity Simulator (BEPS model. Prior to the regional simulation, the annual simulated NPP was validated using field observed NPP demonstrating the ability of BEPS to simulate NPP in different ecosystems of East Asia.

  15. Simulated East-west differences in F-region peak electron density at Far East mid-latitude region

    Science.gov (United States)

    Ren, Z.; Wan, W.

    2017-12-01

    In the present work, using Three-Dimensional Theoretical Ionospheric Model of the Earth in Institute of Geology and Geophysics, Chinese Academy of Sciences (TIME3D-IGGCAS), we simulated the east-west differences in Fregion peak electron density (NmF2) at Far East mid-latitude region.We found that, after removing the longitudinal variations of neutral parameters, TIME3D-IGGCAS can better represent the observed relative east-west difference (Rew) features. Rew is mainly negative (West NmF2 > East NmF2) at noon and positive (East NmF2 >West NmF2) at evening-night. The magnitude of daytime negative Rew is weak at local winter and strong at local summer, and the daytime Rew show two negative peaks around two equinoxes. With the increasing of solar flux level, the magnitude of Rew mainly become larger, and two daytime negative peaks slight shifts to June Solstice. With the decreasing of geographical latitude, Rew mainly become positive, and two daytime negative peaks slight shifts to June Solstice. Our simulation also suggested that the thermospheric zonal wind combined with the geomagnetic field configuration play a pivotal role in the formation of the ionospheric east-west differences at Far East midlatitude region.

  16. The stability margin on EAST tokamak

    International Nuclear Information System (INIS)

    Jin-Ping, Qian; Bao-Nian, Wan; Biao, Shen; Bing-Jia, Xiao; Walker, M.L.; Humphreys, D.A.

    2009-01-01

    The experimental advanced superconducting tokamak (EAST) is the first full superconducting tokamak with a D-shaped cross-sectional plasma presently in operation. Its poloidal coils are relatively far from the plasma due to the necessary thermal isolation from the superconducting magnets, which leads to relatively weaker coupling between plasma and poloidal field. This may cause more difficulties in controlling the vertical instability by using the poloidal coils. The measured growth rates of vertical stability are compared with theoretical calculations, based on a rigid plasma model. Poloidal beta and internal inductance are varied to investigate their effects on the stability margin by changing the values of parameters α n and γ n (Howl et al 1992 Phys. Fluids B 4 1724), with plasma shape fixed to be a configuration with k = 1.9 and δ = 0.5. A number of ways of studying the stability margin are investigated. Among them, changing the values of parameters κ and l i is shown to be the most effective way to increase the stability margin. Finally, a guideline of stability margin M s (κ, l i , A) to a new discharge scenario showing whether plasmas can be stabilized is also presented in this paper

  17. Particle and Power Exhaust in EAST

    Science.gov (United States)

    Wang, Liang; Ding, Fang; Yu, Yaowei; Gan, Kaifu; Liang, Yunfeng; Xu, Guosheng; Xiao, Bingjia; Sun, Youwen; Luo, Guangnan; Gong, Xianzu; Hu, Jiansheng; Li, Jiangang; Wan, Baonian; Maingi, Rajesh; Guo, Houyang; Garofalo, Andrea; EAST Team

    2017-10-01

    A total power injection up to 0.3GJ has been achieved in EAST long pulse USN operation with ITER-like water-cooling W-monoblock divertor, which has steady-state power exhaust capability of 10 MWm-2. The peak temperature of W target saturated at t = 12 s to the value T 500oC and a heat flux 3MWm-2was maintained. Great efforts to reduce heat flux and accommodate particle exhaust simultaneously have been made towards long pulse of 102s time scale. By exploiting the observation of Pfirsch-Schlüter flow direction in the SOL, the Bt direction with Bx ∇B away from the W divertor (more particles favor outer target in USN) was adopted along with optimizing the strike point location near the pumping slot, to facilitate particle and impurity exhaust with the top cryo-pump. By tailoring the 3D divertor footprint through edge magnetic topology change, the heat load was dispersed widely and thus peak heat flux and W sputtering was well controlled. Active feedback control of total radiative power with neon seeding was achieved within frad = 17-35%, exhibiting further potential for heat flux reduction with divertor and edge radiation. Other heat flux handling techniques, including quasi snowflake configuration, will also be presented.

  18. East Kentucky Bioenergy Capacity Assessment Project

    Energy Technology Data Exchange (ETDEWEB)

    Phillips, J. Michael [Morehead State Univ., KY (United States); Montross, Michael [Univ. of Kentucky, Lexington, KY (United States); Mark, Tyler [Morehead State Univ., KY (United States)

    2013-03-31

    When you look across the landscape of Kentucky you will find a very diverse topography. In the western portions of the state you will find fertile and gently rolling soils that are prime land for traditional row crop production. As you move east towards the Appalachian Mountains the terrain becomes increasing roughed and less productive soils. One of the primary objectives of Morehead State University is to serve the eastern Kentucky population of Kentucky. Fitting within that mission is identifying new opportunities for people living in this region. With the passing of the Renewable Fuels Standard in 2005 there was a focus put on the production of biomass crops that can be used in the production of ethanol and cellulosic ethanol. The majority of US ethanol production is derived from corn. The eastern portion of Kentucky is not well suited for corn production, but might be a location for other biomass crops to be produced. Additionally, many farmers in the region were looking for alternative crops to tobacco that might be well suited for the region.

  19. East Greenland tetrapods are Devonian in age

    Science.gov (United States)

    Marshall, J. E. A.; Astin, T. R.; Clack, J. A.

    1999-07-01

    Palynological dates unambiguously resolve the stratigraphic age of the East Greenland sedimentary rocks containing the earliest well-preserved tetrapod remains. This is the first time that spore samples have been discovered in the sedimentary succession that has yielded Acanthostega and Ichthyostega, two tetrapods that are regarded as critically important taxa for our understanding of the origin and early evolution of the tetrapods. These palynological assemblages conclusively show that the rocks are Devonian in age. The evidence resolves a 60-year-old dispute regarding the age of these rocks and contradicts a recent controversial study suggesting a much younger (Carboniferous, Viséan) age for these tetrapods. Spore samples bracketing the in situ occurrences of both tetrapod genera place them securely within the Famennian Age of the Devonian Period and at least as old as Famennian 2b. The ages of all known Devonian tetrapods are reviewed and related to a common palynological standard. This review places Ichthyostega and Acanthostega as the earliest of the Famennian tetrapods.

  20. East-west collaboration in nuclear science

    International Nuclear Information System (INIS)

    Wolfram von, Oertzen

    2002-01-01

    The Sandarski-2 meeting on east-west collaborations in nuclear sciences was held in May 2001 in Bulgaria with 115 participants from 17 European countries, Usa, Japan and Russia (Dubna). The scientific included 66 oral contributions. During the last decade Eastern Europe has undergone substantial political and economic changes. These changes have had a decisive impact on the scientific community in these countries, because the support for basic and applied science has decreased dramatically due to the collapse of economic systems. It should noted that there are still good resources: experimental installations, technical and scientific manpower and a well trained human intellectual reserve but conditions differ strongly from one institute to another. Many national and European institutions have set up support programs for the funding of local activities for scientists in their eastern institutions or by funding collaborations between eastern and western scientists. Many highly specialized eastern scientists work now in Europe, the Usa and Japan but the brain drain from the poorest eastern countries is a real problem. One recommendation put forward at this meeting is the creation of European structures for the support of scientists in their eastern home institutions in such a way that they can return and continue to work at home. (A.C.)

  1. Health promotion in South East Asia.

    Science.gov (United States)

    Mir, N S

    1998-01-01

    The countries of the South East Asia region, which includes Bangladesh, Bhutan, Pakistan, Korea, India, Indonesia, Maldives, Myanmar, Nepal, Sri Lanka, and Thailand, have undertaken a variety of strategies to address the health challenges in the region. The ever-growing pressure of population in the region has allowed rapid transmission of communicable diseases like malaria, tuberculosis (TB), leprosy, and HIV/AIDS. One of the innovative community-based health initiatives in response to this problem is Indonesia's Primary Health Care Project. This project aimed to develop a sustainable health infrastructure by training medical staff, coordinators, village cadres, midwives and those working for TB programs; provision of ongoing guidance and education in this area; and provision of medicines and funds. The project has pioneered a process towards positive changes. Another strategy is the collaboration of youth groups, island development committees, and health workers in Maldives which has led to the declaration of two islands (Madifushi and Haa Alif Berinmadhoo) as 'no smoking' islands. In addition, Sarvodaya has successfully developed a methodology to involve Buddhist monks in AIDS prevention and control through "the Buddhist approach to AIDS prevention in Sri Lanka."

  2. Developing the east coast gas industry

    International Nuclear Information System (INIS)

    Stedman, C.

    1998-01-01

    Development of a natural gas industry on Canada's east coast was discussed. The various stages of near-term and long-term development were outlined. Opportunities were identified in the areas of Grand Banks gas utilization, third party gas and natural gas liquids transportation and processing, cogeneration, petrochemicals and in energy marketing and services. As an example of this industry development, a corporate review of Novagas Canada Ltd., was presented. The company was formed in January 1994 and is wholly owned by Nova Gas International. Novagas Canada has ultimate resources of 62.9 Tcf of natural gas of which 48.9 Tcf remains to be discovered. The company focuses on non-regulated mid-stream operations of the natural gas/natural gas liquid value chain. Some 800 million dollars have been invested so far in gas processing, liquids and olefins businesses in Nova Scotia and the Grand Banks/Labrador area. The pending Nova/TCPL merger will combine Novagas Canada's and TransCanada Gas Services' midstream assets. The general conclusion was that the resource base is large enough to support development throughout the gas and natural gas liquids value chain, and that a critical mass is required to support development of the necessary gas infrastructure. A sizeable challenge remains in encouraging gas utilization, and in encouraging competition, open access and unbundling of energy services. 2 tabs., 2 figs

  3. East European nuclear power plant review

    International Nuclear Information System (INIS)

    Thomas, Steve

    1993-01-01

    Western public opinion regards East European nuclear power plants as inefficient and dangerous. However the plants achieve consistently good operating performances. The load factors achieved by each type of plant by country in 1991 are tabulated. These are shown to be good, especially the Hungarian plant. Load factors seem to be dependent on the type of plant rather than where they were installed. WWER 213s worked better than the WWER 320s. This was because of long shutdowns to try and bring the safety standards up to acceptable levels. RBMK performances were depressed because of a 30% derating by safety authorities on 8 out of the 15 units operating. Overall the picture in Eastern Europe is encouraging with improvements in safety related indicators such as break-down frequency whilst the plants still achieve respectable load factors. The performance of the WWER 320s is particularly encouraging. Good load factors from this type of plant in Russia, the Ukraine and Bulgaria may allow older unsafe plant to be phased out. (UK)

  4. Recent plasma control progress on EAST

    Energy Technology Data Exchange (ETDEWEB)

    Xiao, B.J., E-mail: bjxiao@ipp.ac.cn [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Yuan, Q.P. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China); Humphreys, D.A.; Walker, M.L.; Hyatt, A.W.; Leuer, J.A.; Jackson, G.L. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Mueller, D. [Princeton Plasma Physics Laboratory, Princeton, NJ (United States); Penaflor, B.G.; Pigrowski, D.A.; Johnson, R.D.; Welander, A.S. [General Atomics, P.O. Box 85608, San Diego, CA 92186-5608 (United States); Zhang, R.R.; Luo, Z.P.; Guo, Y.; Xing, Z.; Zhang, Y. [Institute of Plasma Physics, Chinese Academy of Sciences, Hefei (China)

    2012-12-15

    In recent 2 years, various algorithms to control plasma shape, current and density have been implemented or improved for EAST tokamak. These plasma control performances have been verified by either simulated or actual experimental operation, and thus plasma control basis has been established for the long pulse operation and high performance H-mode plasma operation with low hybrid wave (LHW) and ion cyclotron resonance frequency (ICRF) heating. Startup simulation has been done by using TOKSYS code for the plasma breakdown in either 3.1 Wb or 4.5 Wb initial poloidal flux state and the scenarios proved to be robust and used for routine operation. Various shape configurations have been well feedback controlled by using ISOFLUX limited, double-null or single null algorithms based on RTEFIT equilibrium reconstruction. For the long pulse operation, strike point control and magnetics drift compensation have been implemented in the plasma control system (PCS). To improve the operation safety and efficiency, the verification of magnetic diagnostics before plasma breakdown has been demonstrated adequate to prevent a discharge in case of key sensor failure.

  5. East Asian Capital Markets: Integration and Convergence

    Directory of Open Access Journals (Sweden)

    Yana Valeryevna Dyomina

    2016-09-01

    Full Text Available The article examines the interdependence of East Asian stock and bond markets. Hierarchical cluster analysis of bond markets of ten regional countries shows that the most similar ones are the following: Indonesia, Malaysia, the Philippines and Singapore. In 2006-2009 Thailand also belonged with this group, however, since 2010 it is a separate cluster. The second cluster includes Hong Kong, the Republic of Korea and China, the third one - Japan, the fourth one - Vietnam. As for regional equity markets, the study shows that regional stock indices respond to the dynamics of American ones to a greater extent than to the dynamics of each other. In addition, Asian indices’ interconnection is chiefly negative. To assess stock indices’ convergence the author employs cluster analysis which divides 16 studied stock exchanges in 7 different groups. According to the obtained results, the author concludes that integration of regional capital markets is the long-term goal. Besides, markets’ integration will be easier and faster within clusters; inter-cluster mergers will be the next step. The basic problem here arises from the Japanese market, which, in the case of forced or ill-conceived program of events, will absorb all other markets or end up outside the integration processes

  6. NASA's East and Southeast Asia Initiatives: BASE-ASIA and EAST-AIRE

    Science.gov (United States)

    Tsay, S.; Maring, H.

    2005-01-01

    Airborne dust from northern China influences air quality and regional climate in Asia during springtime. However, with the economic growth in China, increased emission of particulate air pollutants from industrial and vehicular sources will not only impact the earth's radiation balance, but also adversely affect human health year round. In addition, both of dust and aerosol pollutants can be transported swiftly across the Pacific affecting North America within a few days. Asian dust and pollutant aerosols can be detected by their colored appearance using current Earth observing satellites (e.g., MODIS, SeaWiFS, TOMS, etc.) and by sunphotometers deployed on the surface of the earth. Biomass burning has been a regular practice for land clearing and conversion in many countries, especially those in Africa, South America, and Southeast Asia. However, the climatology of Southeast Asia is very different than that of Africa and South America, such that large-scale biomass burning causes smoke to interact extensively with clouds during the peak-burning season of March to April. Globally significant sources of greenhouse gases (eg., CO2, CH4), chemically active gases (e.g., NO, CO, HC, CH3Br), and atmospheric aerosols are produced by biomass burning. These gases influence the Earth-atmosphere system, impacting both global climate and tropospheric chemistry. Some aerosols can serve as cloud condensation nuclei, which play a role in determining cloud lifetime and precipitation, altering the earth's radiation and water budgets. Biomass burning also affects the biogeochemical cycling of nitrogen and carbon compounds; the hydrological cycle; land surface reflectivity and emissivity; and ecosystem biodiversity and stability. Two NASA initiatives, EAST-AIRE (East Asian Study of Tropospheric Aerosols: an International Regional Experiment) and BASE-ASIA (Biomass-burning Aerosols in South East-Asia: Smoke Impact Assessment) will be presented. The objectives of these initiatives is to

  7. Records: East African Rarities Committee report and change of remit ...

    African Journals Online (AJOL)

    Scopus: Journal of East African Ornithology. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 29 (2009) >. Log in or Register to get access to full text downloads.

  8. Short communications | Mockler | Scopus: Journal of East African ...

    African Journals Online (AJOL)

    Scopus: Journal of East African Ornithology. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 36, No 1 (2016) >. Log in or Register to get access to full text downloads.

  9. Systematic and taxonomic issues concerning some East African bird ...

    African Journals Online (AJOL)

    Scopus: Journal of East African Ornithology. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 34 (2015) >. Log in or Register to get access to full text downloads.

  10. General practitioners and clinical guidelines | Bhagat | East African ...

    African Journals Online (AJOL)

    East African Medical Journal. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 78, No 1 (2001) >. Log in or Register to get access to full text downloads.

  11. ISSN 2073-9990 East Cent. Afr. J. surg

    African Journals Online (AJOL)

    Hp 630 Dual Core

    To counteract this shortage, many countries are developing or expanding local training programs, both at ... East Africa and Europe. In 2011, the ... workload, work-life balance during the training and remuneration after training. Further studies ...

  12. Climate Prediction Center (CPC) East Atlantic Teleconnection Pattern Index

    Data.gov (United States)

    National Oceanic and Atmospheric Administration, Department of Commerce — Monthly tabulated index of the East Atlantic Teleconnection pattern. The data spans the period 1950 to present. The index is derived from a rotated principal...

  13. Household Density and Infant Care in an East African Society

    Science.gov (United States)

    Munroe, Ruth H.; Munroe, Robert L.

    1971-01-01

    A cross-cultural relationship between household density and infant indulgence was investigated among Logoli infants in East Africa. Findings were taken as supportive of the view that socialization practices are influenced by ecological variables. (Author/JB)

  14. Eye Munchausen's Syndrome: Case Report | Atipo-Tsiba | East ...

    African Journals Online (AJOL)

    East African Medical Journal. Journal Home · ABOUT THIS ... Munchausen's syndrome is a psychiatric disorder characterised by a need to simulate a disease or trauma self-mutilation, in order to attract attention or sympathy. Patients with this ...

  15. Gastric outlet obstruction in Northwestern Ethiopia | Kotisso | East ...

    African Journals Online (AJOL)

    East and Central African Journal of Surgery. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 5, No 2 (2000) >. Log in or Register to get access to full text downloads.

  16. Gastric cancers at Kibogora Hospital | Ntakiyiruta | East and Central ...

    African Journals Online (AJOL)

    East and Central African Journal of Surgery. Journal Home · ABOUT THIS JOURNAL · Advanced Search · Current Issue · Archives · Journal Home > Vol 14, No 1 (2009) >. Log in or Register to get access to full text downloads.

  17. Water Management in Africa and the Middle East: Challenges and ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Book cover Water Management in Africa and the Middle East: Challenges and ... key issues and trends, and map out strategies for further research and action. ... and adaptive water management: Innovative solutions from the Global South”.

  18. Improved density measurement by FIR laser interferometer on EAST tokamak

    International Nuclear Information System (INIS)

    Shen, Jie; Jie, Yinxian; Liu, Haiqing; Wei, Xuechao; Wang, Zhengxing; Gao, Xiang

    2013-01-01

    Highlights: • In 2012, the water-cooling Mo wall was installed in EAST. • A schottky barrier diode detector is designed and used on EAST for the first time. • The three-channel far-infrared laser interferometer can measure the electron density. • The improved measurement and latest experiment results are reported. • The signal we get in this experiment campaign is much better than we got in 2010. -- Abstract: A three-channel far-infrared (FIR) hydrogen cyanide (HCN) laser interferometer is in operation since 2010 to measure the line averaged electron density on experimental advanced superconducting tokamak (EAST). The HCN laser signal is improved by means of a new schottky barrier diode (SBD) detector. The improved measurement and latest experiment results of the three-channel FIR laser interferometer on EAST tokamak are reported

  19. The latest development of EAST neutral beam injector

    International Nuclear Information System (INIS)

    Hu Chundong; Xu Yongjian

    2014-01-01

    As the first full superconducting non-circular cross section Tokomak in the world, EAST is used to explore the forefront physics and engineering issues on the construction of Tokomak fusion reactor. Neutral beam injection has been recognized as one of the most effective means for plasma heating. According to the research plan of the EAST physics experiment, a set of neutral beam injector (4∼8 MW, 10∼100 s)will be built and operational in 2014. The paper presents the latest development of EAST neutral beam injector and the latest experiment results of long pulse beam extraction and high power beam extraction are reported, those results show that all targets reach or almost reach the design targets. All these will lay a solid foundation for the achievement of plasma heating and current drive for EAST in 2014. (authors)

  20. Cold war, quantum foundations, and East-West collaboration

    Energy Technology Data Exchange (ETDEWEB)

    Skaar-Jacobsen, Anja [Niels Bohr Archive, Copenhagen (Germany)

    2011-07-01

    It is well-known that the cultural cold war changed the ideological line in the Soviet Union from the late 1940s and that this had serious implications for the autonomy of research in genetics and quantum foundations in the East bloc. However, besides the more narrow concern from the point of view of research in quantum foundations, I suggest that the ideological impact on quantum foundations also constituted an obstacle for attempts by Western physicists to bring about a rapprochement between physics in the east and west in general. In connection with re-establishing East-West co-operation between physicists after Stalin's death in 1953 this obstacle needed to be cleared away. In my talk I discuss these issues and how the Institute for Theoretical Physics in Copenhagen came to be an important meeting place for physicists from the East and West from the mid-1950s.