Process analysis of biofuelled heat and power plants integrated with a flue gas dryer; Processtudie av biobraensleeldade kraftvaermeverk integrerade med roekgastork

Energy Technology Data Exchange (ETDEWEB)

Johansson, Kent; Steinwall, Pontus [Sycon Energikonsult AB, Malmoe (Sweden)

2000-01-01

In this report three different processes for combined heat and power production from biomass have been evaluated and compared. Both economical and technical questions have been investigated. The examined processes are: 1. CFB fuelled with wet biomass; 2. A boiler fuelled with pulverised biomass integrated with a traditional flue gas dryer; and 3. A boiler fuelled with pulverized biomass integrated with a flue gas dryer with a closed loop. All the processes have a district heat output of 80 MW. Calculations have been made at three different loads: 100, 70 and 40 % respectively. The performance characteristics in form of electric efficiency and fuel utilisation are very similar for the processes. To evaluate the thermodynamic differences between the processes, calculations have been made with extreme temperatures in the district heating net, 65 deg C/100 deg C. The process with a closed loop drier has a saturation temperature in the flue gas of 95 deg C. Therefore this process has a high fuel utilization even if the incoming water has a high temperature. The fuel utilization for alternatives 1 and 2 decreases almost down to the efficiency of the furnace. This shows that the temperature of the water is too high to recapture the latent heat in the flue gases. The investment costs for the processes have been estimated. Also these are very similar for the three alternatives. The cost for the process with the CFB is 412 million SEK. The boiler in alternative 2 and 3 is approximately 20 million SEK cheaper than the CFB. The decreased cost for the boiler is compensated by the cost for the dryers. The investment cost for the traditional dryer has been estimated to 20 million SEK and 30 million SEK for the closed loop dryer. The total cost for alternative 2 is then 417 million SEK and 414 million SEK for alternative 3. Operation and maintenance costs for the processes with dryer are supposed to be 1 respectively 1.5 million SEK higher than for alternative 1. The dryers may

Heat pump dryers theory, design and industrial applications

CERN Document Server

Alves-Filho, Odilio

2015-01-01

Explore the Social, Technological, and Economic Impact of Heat Pump Drying Heat pump drying is a green technology that aligns with current energy, quality, and environmental concerns, and when compared to conventional drying, delivers similar quality at a lower cost. Heat Pump Dryers: Theory, Design and Industrial Applications details the progression of heat pump drying-from pioneering research and demonstration work to an applied technology-and establishes principles and theories that can aid in the successful design and application of heat pump dryers. Based on the author's personal experience, this book compares heat pump dryers and conventional dryers in terms of performance, quality, removal rate, energy utilization, and the environmental effect of both drying processes. It includes detailed descriptions and layouts of heat pump dryers, outlines the principles of operation, and explains the equations, diagrams, and procedures used to form the basis for heat pump dryer dimensioning and design. The author ...

Operation experiences of biofuel dryers; Drifterfarenheter fraan aangtorkar och direkta roekgastorkar

Energy Technology Data Exchange (ETDEWEB)

Berge, Christian; Dejfors, Charlotte [AaF Energikonsult Stockholm AB (Sweden)

2000-01-01

A study regarding operation experiences of indirect steam dryers and direct flue gas dryers of biofuels has been conducted. In the study, plants with the two types of dryers have been visited and operational experiences have been gathered and analysed. Results show that the well proven technique with flue gas dryers has a higher availability than the steam dryers. Several plants have problem with the feeding and discharge systems. Material selection is very important to prevent corrosion. Indirect steam dryers have more environmental regulations than flue gas dryers because of the generated condensate from the fuel drying process. Future work should concentrate on material selections, refining the feeding and discharge systems and control system.

Bed mixing dryer for high moisture content fuels

Energy Technology Data Exchange (ETDEWEB)

Hulkkonen, S; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

1998-12-31

Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

Bed mixing dryer for high moisture content fuels

Energy Technology Data Exchange (ETDEWEB)

Hulkkonen, S.; Heinonen, O. [Imatran Voima Oy, Vantaa (Finland)

1997-12-31

Bed mixing dryer is a new type of fuel drying technology for fluidized bed combustion. The idea is to extract hot bed material from the fluidized bed and use it as a heat source for drying the fuel. Drying occurs at steam atmosphere which makes it possible to recover the latent heat of evaporation to process. This improves the thermal efficiency of the power plant process considerably, especially in combined heat and power applications. Imatran Voima Oy (IVO) has developed the Bed Mixing Dryer technology since early 1990s. The first pilot plant was built in 1994 to IVO`s Kuusamo peat and wood fired power plant. The capacity of the plant is 6 MW{sub e} and 20 MW of district heat. In Kuusamo the dryer is connected to a bubbling fluidized bed. Since it`s commissioning the dryer has been used successfully for about 3000 hours during the heating season in wintertime. The second application of the technology will be a demonstration project in Oerebro (S). IVO Power Engineering Ltd will supply in 1997 a dryer to Oerebro Energi`s peat, wood and coal fired CHP plant equipped with circulating fluidized bed boiler. The fuel to be dried is sawdust with fuel input of about 60 MW. In Kuusamo the dryer produces 3 MW of additional district heat and in Oerebro 6 MW. The fuels in Kuusamo are peat, saw dust and bark. In addition to the municipal heat production this type of drying technology has its benefits in pulp and paper industry processes. Disposal of paper mill sludges is becoming more difficult and costly which has resulted in need of alternative treatment. Drying of the sludge before combustion in a boiler for power production is an attractive option. At the moment IVO is carrying out several studies to apply the Bed Mixing Dryer in pulp and paper industry processes. Economy of drying the sludge looks promising

Test of a solar crop dryer

Energy Technology Data Exchange (ETDEWEB)

Oestergaard Jensen, S. [Teknologisk Institut. SolEnergiCentret, Taastrup (Denmark); Floejgaard Kristensen, E. [Danmarks JordbrugsForskning, Tjele (Denmark); Forman, T. [Aidt Miljoe A/S, Thorsoe (Denmark)

2001-01-01

One of the major goals of the project 'Test and Research Project into the Drying of Food and Wood Products with Solar Heat' was to develop and test a solar crop dryer for use in Ghana. Based on a survey in Ghana (Jensen, Frank and Kristensen, 1999) it was decided to develop a dryer for drying of maize for seed as the increase in value of the crop due the drying here would be high - the dryer may, however, also be used to dry other crops or other items - one unit will e.g. be erected in Ghana to test drying of fish. The capacity of the dryer was defined to be 500 kg having a collector area of approx 25 m{sup 2}. It was decided to let the dryer consist of 5 separate units each with a transparent collector area of 4.77 m{sup 2} and a capacity of approx. 100 kg. The modulized concept has several benfits: If one drying bed is operated improperly this will not affect the total quantity of crops being dried at that time. It is possible to dry different crops (creating different pressure drop) side by side without risking that the crop with the highest pressure drop will be dried improperly. Small dc fans are often cheaper than larger dc fans. The system will be less complex, and an even air distribution over the drying bed is easier obtainable. Finally it is possible to start with only one unit and then gradually increase the capacity of the solar dryer - this will make it easier to invest in a solar dryer. It was further decided that the fans of the dryer should be powered directly by PV-panels in order to make the dryer independent of an often unreliable, missing or expensive grid. The dryer is going to be erected and tested at Silwood Farms situated close to Accra. Silwood Farms has total land acreage of 210 acres where 176 acres are used for cultivating maize - the rest is used for gowing pineapple. A majority of the maize is processed into seed. The main harvest season for maize at Silwood Farms is August/September with a smaller harvest period in January

Experimental investigations of a chimney-dependent solar crop dryer

Energy Technology Data Exchange (ETDEWEB)

Afriyie, J.K.; Nazha, M.A.A.; Rajakaruna, H. [School of Engineering and Technology, De Montfort University, Queens Building, The Gateway, Leicester LE1 9BH (United Kingdom); Forson, F.K. [Department of Mechanical Engineering, Kwame Nkrumah University of Science and Technology, Kumasi (Ghana)

2009-01-15

An experimental investigation into the performance of a solar crop dryer with solar chimney and no air preheating is described. Tests were first performed on the cabinet dryer, using a normal chimney. The trials were repeated with a solar chimney. Still with the solar chimney, further trials were carried out with the roof of the drying chamber inclined further to form a tent dryer. The described tests include no-load tests for airflow rate measurements and drying tests, with cassava as the crop. Air velocities, temperatures, ambient relative humidity and the drop in crop moisture contents at different stages of the drying process are also presented. The effects of the various configurations described above on the drying process are deduced and discussed while comparing the experimental results with one another. In addition, the performance of the dryer in relation to other natural convection dryers is discussed. The results show that the solar chimney can increase the airflow rate of a direct-mode dryer especially when it is well designed with the appropriate angle of drying-chamber roof. However, the increase in flow rate only increases the drying rate when the relative humidity (RH) of the ambient air is below a certain mark (60% for cassava). (author)

Test of solar dryers in Ghana

Energy Technology Data Exchange (ETDEWEB)

Oestergaard Jensen, S. [Teknologisk Institut. SolEnergiCentret, Taastrup (Denmark); Floejgaard Kristensen, E. [Danmarks JordbrugsForskning, Tjele (Denmark); Agyei, F. [FAGOD Ltd. (Ghana); Larsen, T. [Clipper Design Ltd. (Ghana); Nketiah, K.S. [FORIG (Ghana)

2002-06-01

The report describes the tests carried out in Ghana on three solar dryers as part of the project 'Test and Research Project into the Drying of Food and Wood Products with Solar Heat' financed by DANIDA. The main objective of the project was to develop and test solar dryers for crop, fish and wood in Ghana. Three dryers were erected: 1. Solar crop dryer: The solar crop dryer was erected at Silwood Farms at Pokuase about 30 km north of Accra. Silwood Farms grows primarily maize for seed and pineapples, 2. Solar fish dryer: The solar fish dryer was erected at Elite Enterprise Ltd. at Tema about 35 km east-north-east of Accra. Elite Enterprise Ltd. buys and dries fish, 3. Solar wood dryer: The solar wood dryers were erected at Clipper Design Ltd. at Mankoadze about 65 km west-south-west of Accra. Clipper Design Ltd. produces mainly doors. (BA)

Tribological Aspects of the Process of Winding the Steel Rope Around the Winch Drum

Directory of Open Access Journals (Sweden)

M. Matejić, , , ,

2014-03-01

Full Text Available Proper winding of the steel rope around the winch drum is great importance, mostly for: prolonging the service life of the rope, reduction of deformations of the body and the sides of the drum if the winding of the rope is multilayered, increasing of the safety factors, easier unwinding of the rope while lowering the load, even running of the drive unit, etc. The focus of this paper is on the analysis of the friction which occurs in the process of winding and unwinding the rope around the winch drum. Friction force is in its highest intensity when the rope passes from one layer to another, if the winding of the rope is multilayered. As the result of the research, certain mechanisms of winding of the rope from the aspects of the friction force were obtained, and the effects of the forces on the sides of the drum were analyzed.

Energy Efficient Clothes Dryer with IR Heating and Electrostatic Precipitator

Energy Technology Data Exchange (ETDEWEB)

Weaver, Stanton [GE Global Research, Niskayuna, NY (United States)

2017-12-12

The project goal was to develop a revolutionary energy saving technology for residential clothes drying. The team developed an IR (infrared) heating system and NESP (Nebulizer and Electro-Static Precipitator) for integration into a ventless clothes dryer. The proposed technology addresses two of the major inefficiencies in current electric vented dryers by providing effective energy transfer for the removal of the water and recapture of the vapor latent heat. The IR heaters operating in the mid wave (2.5-10um) are very efficient as they target the 3-micron peak absorption of the water molecule. This allows direct energy absorption, unlike conventional element heaters where heat is transferred by convection. The low power NESP removes water vapor from the exhausted stream and recaptures the latent heat in the ESP (Electro-Static Precipitator) exchanger section. This allows the warm dry air to be recirculated back into the drum for additional efficiency savings. The remaining majority of the dryer hardware stays the same. Summing the efficiency gain from the two subcomponents we anticipated the EF (Efficiency Factor) to exceed the goal of 4.04. EF is obtained by dividing the weight (lbs) of water removed by the energy (kWhr) used, where the test load size is 8.45 lbs of bone dry clothing wetted to 57.5% or 4.8lbs of water, and dried to a remaining moisture content of 2.5-5%. Additional benefits include not having to recondition (heat or cool) the large amounts of make-up air to replace the air exhausted by a vented dryer. It was anticipated that the NESP/heat exchanger would be the most challenging and highest risk element in the program. Therefore, the team focused their efforts during Phase 1 of the program on the design, construction, testing, and optimization of the NESP/heat exchanger. At the end Phase 1, the team compared the performance of the NESP/heat exchanger with the system level requirements and made a Go/No-Go decision on proceeding with the second

Drying wood waste with a pulse combustion dryer

Energy Technology Data Exchange (ETDEWEB)

Buchkowski, A.G. [Spectrum Engineering Corp., Ltd., Peterborough, Ontario (Canada); Kitchen, J.A. [John A. Kitchen, Ltd., Hastings, Ontario (Canada)

1993-12-31

There is a vast amount of wood waste available to be used as an alternate fuel if its moisture could be reduced efficiently. Tests have been conducted to assess an industrial dryer using pulse combustion as a heating source for drying wood waste; specifically sawdust and pulverized wet hog fuel. Pulse combustion offers the advantage of high heat transfer, efficient combustion, and low NO{sub x} emissions. The material is injected into the exhaust gases in the tailpipe of the combustor which uses natural gas or propane as a fuel. The turbulence created by the pulsations enhance the drying process by reducing the boundary layer thicknesses. The materials is further dried in a rotary drum. The material has been dried without scorching or burning in tests where the inlet moisture content has been as high as 60% on a wet basis. The outlet moisture contents achieved have typically been 10%. Analysis of the test data and cost estimates of the equipment indicate that the pulse combustion drying system is at least comparable to existing systems in terms of operating costs, and offers very significant savings in capital costs. Testing with various other materials such as wood pulp, sludges and peat is continuing to further assess the equipment`s performance.

Correlations of Mean Process Parameters for Agricultural Products Drying in Thin Bed in Solar Direct Dryers

Directory of Open Access Journals (Sweden)

MSc. Ciro César Bergues-Ricardo

2015-11-01

Full Text Available A group of correlations is given between mean parameters of drying process drying velocity, energy losses, useful energy, and thermal efficiency. Those are suitable for conditions of thin bed drying, in direct solar dryers, and may help for developing of an integral approach of solar drying in those conditions. Correlations are reliable for drying processes of diverse crop products specified, suchas roots, seeds, vegetables, fruits, wood, etc, with natural or forced convection. Correlations were validated in Cuba for usual ranges of efficiency and products in solar dryers of cover, cabinet and house types, in tropical conditions. These correlations are useful for design and exploitation ofdryers and for theoretical and practical comprehension of solar drying like a system.

HANFORD Pu-238 DRUM INTEGRITY ASSESSMENT

International Nuclear Information System (INIS)

CANNELL, G.R.

2004-01-01

Hanford is presently retrieving contact-handled, transuranic (CH-TRU) waste drums from the site's Low-Level Burial Grounds (LLBG) for processing and disposition. A subgroup of these drums (12 total), referred to as Pu-238 drums, has some unique characteristics that may impact the current drum handling and processing activities. These characteristics include content, shielding, thermal, pressurization and criticality issues. An effort to evaluate these characteristics, for the purpose of developing a specific plan for safe retrieval of the Pu-238 drums, is underway. In addition to the above evaluation, the following integrity assessment of the inner container material and/or confinement properties, with primary emphasis on the Source Capsule (primary confinement barrier) and Shipping Container has been performed. Assessment included review of the inner container materials and the potential impact the service history may have had on material and/or confinement properties. Several environmental degradation mechanisms were considered with the objective of answering the following question: Is it likely the container material and/or confinement properties have been significantly altered as a result of service history?

New complex-dryers with RE for coatings

International Nuclear Information System (INIS)

Ge, G.

1998-01-01

Full text: The complex coating dryers are produced with good 2-Ethylhexanoic acid, rare earths and other metals. Simply using such a complex drier can get the total effect instead of the traditional dryers such as Co, Mn, Pb, Zn, Ca etc. It has advantages of saving quantity, decreasing cost, simplifying process, making the operation convenient, good quality, good stability and without Pb. Invention patent of China requisition number is 95119867.X

Predictions and implications of a poisson process model to describe corrosion of transuranic waste drums

International Nuclear Information System (INIS)

Lyon, B.F.; Holmes, J.A.; Wilbert, K.A.

1995-01-01

A risk assessment methodology is described in this paper to compare risks associated with immediate or near-term retrieval of transuranic (TRU) waste drums from bermed storage versus delayed retrieval. Assuming a Poisson process adequately describes corrosion, significant breaching of drums is expected to begin at - 15 and 24 yr for pitting and general corrosion, respectively. Because of this breaching, more risk will be incurred by delayed than by immediate retrieval

The coke drum thermal kinetic effects

Energy Technology Data Exchange (ETDEWEB)

Aldescu, Maria M.; Romero, Sim; Larson, Mel [KBC Advanced Technologies plc, Surrey (United Kingdom)

2012-07-01

The coke drum thermal kinetic dynamics fundamentally affect the coker unit yields as well as the coke product properties and unit reliability. In the drum the thermal cracking and polymerization or condensation reactions take place in a semi-batch environment. Understanding the fundamentals of the foaming kinetics that occur in the coke drums is key to avoiding a foam-over that could result in a unit shutdown for several months. Although the most dynamic changes with time occur during drum filling, other dynamics of the coker process will be discussed as well. KBC has contributed towards uncovering and modelling the complexities of heavy oil thermal dynamics. (author)

Integration of thickener underflow into thermal dryer circuit. Final report

Energy Technology Data Exchange (ETDEWEB)

McClaine, A.W.; Breault, R.W.

1998-12-31

A large number of coal preparation plants in the United States are troubled with coal fines and associated plant operation problems. As part of their process, these plants use thermal dryers for producing product coal, cyclones for first-stage recovery of coal fines, and wet scrubbers for the second-stage removal of coal fines carry-over from the dryer exhaust gas. The first challenge for these plants is to recover the clean ultra-fine coal captured in the scrubbers rather than to dispose of it in settling ponds. The second challenge is to mitigate the over-dry fine coal dusting problems in the dryer product. Prior to the completion of this program, the difficulties of the first challenge involving the recovery and use of fine clean coal from the thermal dryer scrubber effluent had not been solved. The second challenge, controlling fine coal dusting, was previously met by applying a solution of surfactants and process water to the over-dry coal fraction. As a result of the demonstration provided by the performance of this program, the implementation of a simple process improvement, involving the use of a thickener in combination with a belt press, simultaneously solved both challenges: the de-dusting and the dryer scrubber effluent recovery issues. The objective of this project was to: (1) Use a clean coal thickener with a squeeze belt press to recover the ultra-fine coal in dryer scrubber effluent; (2) Demonstrate that the coal-water mixture (CWM) produced from scrubber sludge of a thermal dryer can be used as a dust suppressant. The thickener/belt press system has increased the production of JWRI Mine Number 4 by approximately 0.7%. This production increase was accomplished by recovering and re-using 3 metric tons/hr (3.3 tons/hr) of coal fines that were previously sent to holding ponds, returning this as a 50% CWM to de-dust the 430 metric tons/hr (470 tons/hr) of existing dryer production.

The effect of dryer load on freeze drying process design.

Science.gov (United States)

Patel, Sajal M; Jameel, Feroz; Pikal, Michael J

2010-10-01

Freeze-drying using a partial load is a common occurrence during the early manufacturing stages when insufficient amounts of active pharmaceutical ingredient (API) are available. In such cases, the immediate production needs are met by performing lyophilization with less than a full freeze dryer load. However, it is not obvious at what fractional load significant deviations from full load behavior begin. The objective of this research was to systematically study the effects of variation in product load on freeze drying behavior in laboratory, pilot and clinical scale freeze-dryers. Experiments were conducted with 5% mannitol (high heat and mass flux) and 5% sucrose (low heat and mass flux) at different product loads (100%, 50%, 10%, and 2%). Product temperature was measured in edge as well as center vials with thermocouples. Specific surface area (SSA) was measured by BET gas adsorption analysis and residual moisture was measured by Karl Fischer. In the lab scale freeze-dryer, the molar flux of inert gas was determined by direct flow measurement using a flowmeter and the molar flux of water vapor was determined by manometric temperature measurement (MTM) and tunable diode laser absorption spectroscopy (TDLAS) techniques. Comparative pressure measurement (capacitance manometer vs. Pirani) was used to determine primary drying time. For both 5% mannitol and 5% sucrose, primary drying time decreases and product temperature increases as the load on the shelves decreases. No systematic variation was observed in residual moisture and vapor composition as load decreased. Further, SSA data suggests that there are no significant freezing differences under different load conditions. Independent of dryer scale, among all the effects, variation in radiation heat transfer from the chamber walls to the product seems to be the dominant effect resulting in shorter primary drying time as the load on the shelf decreases (i.e., the fraction of edge vials increases).

Tropical field performance of dual-pass PV tray dryer

Science.gov (United States)

Iskandar, A. Noor; Ya'acob, M. E.; Anuar, M. S.

2017-09-01

Solar Photovoltaic technology has become the preferable solution in many countries around the globe to solve the ever increasing energy demand of the consumers. In line with the consumer need, food processing technology has huge potentials of integration with the renewable energy resources especially in drying process which consumes the highest electricity loads. Traditionally, the solar dryer technology was applied in agriculture and food industries utilizing the sun's energy for drying process, but this is highly dependable on the weather condition and surrounding factors. This work shares some field performance of the new design of portable dual-pass PV tray dryer for drying crops in an enclosed system. The dual-pass PV tray dryer encompass a lightweight aluminium box structure with dimensions of 1.1m (L) x 0.6m (W) x 0.2m (H) and can hold a load capacity of 300g - 3kg of crop depending on the types of the crops. Experiments of field performance monitoring were conducted in October -November 2016 which justifies a considerable reduction in time and crops quality improvement when using the dual-pass PV tray dryer as compared to direct-sun drying.

Performance of indirect solar cabinet dryer

International Nuclear Information System (INIS)

Sreekumar, A.; Manikantan, P.E.; Vijayakumar, K.P.

2008-01-01

In this paper, the development and testing of a new type of efficient solar dryer, particularly meant for drying vegetables and fruit, is described. The dryer has two compartments: one for collecting solar radiation and producing thermal energy and the other for spreading the product to be dried. This arrangement was made to absorb maximum solar radiation by the absorber plate. In this dryer, the product was loaded beneath the absorber plate, which prevented the problem of discoloration due to irradiation by direct sunlight. Two axial flow fans, provided in the air inlet, can accelerate the drying rate. The dryer had six perforated trays for loading the material. The absorber plate of the dryer attained a temperature of 97.2 deg. C when it was studied under no load conditions. The maximum air temperature in the dryer, under this condition was 78.1 deg. C. The dryer was loaded with 4 kg of bitter gourd having an initial moisture content of 95%, and the final desired moisture content of 5% was achieved within 6 h without losing the product colour, while it was 11 h for open sun drying. The collector glazing was inclined at a particular angle, suitable to the location, for absorption of maximum solar radiation. A detailed performance analysis was done by three methods, namely 'annualized cost method', 'present worth of annual savings' and 'present worth of cumulative savings'. The drying cost for 1 kg of bitter gourd was calculated as Rs. 17.52, and it was Rs. 41.35, in the case of an electric dryer. The life span of the solar dryer was assumed to be 20 years. The cumulative present worth of annual savings over the life of the solar dryer was calculated for bitter gourd drying, and it turned out be Rs. 31659.26, which was much higher than the capital cost of the dryer (Rs. 6500). The payback period was calculated as 3.26 years, which was also very small considering the life of the system (20 years). So, the dryer would dry products free of cost during almost its

Short-time leaching behaviour of a cement-matrix incorporating soluble radioactive aggregates

International Nuclear Information System (INIS)

Daniels, H.; Kalitz, C.; Kuhne, L.; Steinhardt, T.; Caspary, G.; Printz, R.; Scherer, U.W.

2015-01-01

As the chemical characterisations of certain cement-based radioactive waste-forms produced by the Nuclear-Services of Juelich Research Centre were not yet fully available, a related study was conducted. In this work the interaction of a specific cement-matrix with incorporated radioactive aggregates, so-called drum-dryer product, was investigated. Therefore, representative cement-samples containing the radioactive waste were taken. The main focus was laid on these samples' behaviour under leaching conditions to quantify soluble and insoluble compounds. Additionally, possible chemical interactions of cement components with drum-dryer product were evaluated. For these purposes, chemical analytics as well as physical methods for characterisation and structural evaluation of the waste-form' s behaviour were used. The leaching experiments lasted for up to 39 days. A comparison of the results of the elementary and ion-chromatographic analysis before and after leaching of the samples was carried out. This lead to the deduction that the majority of the drum-dryer product is not incorporated in the cement matrix in the form of insoluble compounds like a solid solution. Although structural examinations showed the formation of an Apatite-phase that is not characteristic for portland cement, they also supported the measured overall high leachability of the cemented drum-dryer products. It can be concluded that the chemical interaction between the cement matrix and drum-dryer product during and after cementation plays a subordinate, yet not negligible, role with respect to solubility of the drum dryer product under aqueous leaching conditions. Additionally, it can be postulated that the drum-dryer product did not undergo substantial chemical alteration in the environment created by the cement-matrix and the respective leaching experiments. (authors)

Rotary drum for centrifuge

International Nuclear Information System (INIS)

Sakurai, Mitsuo; Ichinoto, Seiichi.

1972-01-01

An outwardly concaved metallic end plate is fitted into each end of a metallic rotary drum for a centrifuge until each end face of the drum is brought to bear upon a section of the end plate radially projected in a direction perpendicular to the axis of rotation of the drum, said section being provided at the marginal edge of the end plate. Following completion of the fitting operation, the end plate is welded to the rotary drum. During high speed rotation, the drum contracts axially and expands radially, while the concave end plate, radially tensioned due to the radial expansion of the drum, undergoes a reduction in its degree of concavity resulting in outwardly directed axial displacement of the end plate proper its marginal edge remaining unaffected relative to the drum. Such displacement conpensates for axial contraction of the drum. Since displacement of the end plate and contraction of the drum depend upon the speed of rotation, substantial axial distortion of the drum can be avoided relative to the end plates at both low and high speeds to permit a high degree of balance for the rotary drum. (Ohno, Y.)

Performance of indirect solar cabinet dryer

Energy Technology Data Exchange (ETDEWEB)

Sreekumar, A.; Manikantan, P.E.; Vijayakumar, K.P. [Solar Thermal Energy Laboratory, Department of Physics, Cochin University of Science and Technology, Kochi 682 022 (India)

2008-06-15

In this paper, the development and testing of a new type of efficient solar dryer, particularly meant for drying vegetables and fruit, is described. The dryer has two compartments: one for collecting solar radiation and producing thermal energy and the other for spreading the product to be dried. This arrangement was made to absorb maximum solar radiation by the absorber plate. In this dryer, the product was loaded beneath the absorber plate, which prevented the problem of discoloration due to irradiation by direct sunlight. Two axial flow fans, provided in the air inlet, can accelerate the drying rate. The dryer had six perforated trays for loading the material. The absorber plate of the dryer attained a temperature of 97.2 C when it was studied under no load conditions. The maximum air temperature in the dryer, under this condition was 78.1 C. The dryer was loaded with 4 kg of bitter gourd having an initial moisture content of 95%, and the final desired moisture content of 5% was achieved within 6 h without losing the product colour, while it was 11 h for open sun drying. The collector glazing was inclined at a particular angle, suitable to the location, for absorption of maximum solar radiation. A detailed performance analysis was done by three methods, namely 'annualized cost method', 'present worth of annual savings' and 'present worth of cumulative savings'. The drying cost for 1 kg of bitter gourd was calculated as Rs. 17.52, and it was Rs. 41.35, in the case of an electric dryer. The life span of the solar dryer was assumed to be 20 years. The cumulative present worth of annual savings over the life of the solar dryer was calculated for bitter gourd drying, and it turned out be Rs. 31659.26, which was much higher than the capital cost of the dryer (Rs. 6500). The payback period was calculated as 3.26 years, which was also very small considering the life of the system (20 years). So, the dryer would dry products free of cost

TRU drum corrosion task team report

Energy Technology Data Exchange (ETDEWEB)

Kooda, K.E.; Lavery, C.A.; Zeek, D.P.

1996-05-01

During routine inspections in March 1996, transuranic (TRU) waste drums stored at the Radioactive Waste Management Complex (RWMC) were found with pinholes and leaking fluid. These drums were overpacked, and further inspection discovered over 200 drums with similar corrosion. A task team was assigned to investigate the problem with four specific objectives: to identify any other drums in RWMC TRU storage with pinhole corrosion; to evaluate the adequacy of the RWMC inspection process; to determine the precise mechanism(s) generating the pinhole drum corrosion; and to assess the implications of this event for WIPP certifiability of waste drums. The task team investigations analyzed the source of the pinholes to be Hcl-induced localized pitting corrosion. Hcl formation is directly related to the polychlorinated hydrocarbon volatile organic compounds (VOCs) in the waste. Most of the drums showing pinhole corrosion are from Content Code-003 (CC-003) because they contain the highest amounts of polychlorinated VOCs as determined by headspace gas analysis. CC-001 drums represent the only other content code with a significant number of pinhole corrosion drums because their headspace gas VOC content, although significantly less than CC-003, is far greater than that of the other content codes. The exact mechanisms of Hcl formation could not be determined, but radiolytic and reductive dechlorination and direct reduction of halocarbons were analyzed as the likely operable reactions. The team considered the entire range of feasible options, ranked and prioritized the alternatives, and recommended the optimal solution that maximizes protection of worker and public safety while minimizing impacts on RWMC and TRU program operations.

TRU drum corrosion task team report

International Nuclear Information System (INIS)

Kooda, K.E.; Lavery, C.A.; Zeek, D.P.

1996-05-01

During routine inspections in March 1996, transuranic (TRU) waste drums stored at the Radioactive Waste Management Complex (RWMC) were found with pinholes and leaking fluid. These drums were overpacked, and further inspection discovered over 200 drums with similar corrosion. A task team was assigned to investigate the problem with four specific objectives: to identify any other drums in RWMC TRU storage with pinhole corrosion; to evaluate the adequacy of the RWMC inspection process; to determine the precise mechanism(s) generating the pinhole drum corrosion; and to assess the implications of this event for WIPP certifiability of waste drums. The task team investigations analyzed the source of the pinholes to be Hcl-induced localized pitting corrosion. Hcl formation is directly related to the polychlorinated hydrocarbon volatile organic compounds (VOCs) in the waste. Most of the drums showing pinhole corrosion are from Content Code-003 (CC-003) because they contain the highest amounts of polychlorinated VOCs as determined by headspace gas analysis. CC-001 drums represent the only other content code with a significant number of pinhole corrosion drums because their headspace gas VOC content, although significantly less than CC-003, is far greater than that of the other content codes. The exact mechanisms of Hcl formation could not be determined, but radiolytic and reductive dechlorination and direct reduction of halocarbons were analyzed as the likely operable reactions. The team considered the entire range of feasible options, ranked and prioritized the alternatives, and recommended the optimal solution that maximizes protection of worker and public safety while minimizing impacts on RWMC and TRU program operations

Type B Drum packages

International Nuclear Information System (INIS)

Edwards, W.S.

1995-11-01

The Type B Drum package is a container in which a single drum containing Type B quantities of radioactive material will be packaged for shipment. The Type B Drum containers are being developed to fill a void in the packaging and transportation capabilities of the US Department of Energy (DOE), as no double containment packaging for single drums of Type B radioactive material is currently available. Several multiple-drum containers and shielded casks presently exist. However, the size and weight of these containers present multiple operational challenges for single-drum shipments. The Type B Drum containers will offer one unshielded version and, if needed, two shielded versions, and will provide for the option of either single or double containment. The primary users of the Type B Drum container will be any organization with a need to ship single drums of Type B radioactive material. Those users include laboratories, waste retrieval facilities, emergency response teams, and small facilities

Test and study for dryer used in steam generator

International Nuclear Information System (INIS)

Xue Yunkui; Liu Shixun; Xie Guandao; Chen Junliang

1994-10-01

Dryer used in steam generator is composed of hooked-vanes and draining structure. The influences of the number of drainage hooks on a hooked-vane, bending angle, distance between two adjacent hooked-vanes, etc. on separation effect are introduced. The improving process of draining structure is also described. The test indicates that the hooked-vanes type dryer allows to change inlet moisture in a large range and that the performance of the dryer is closely related to draining structure. A draining structure with original creation which is selected by the test is presented, its drainage effect is better than that of similar structures at home and abroad. (2 tabs., 21 figs.)

[Thermal energy utilization analysis and energy conservation measures of fluidized bed dryer].

Science.gov (United States)

Xing, Liming; Zhao, Zhengsheng

2012-07-01

To propose measures for enhancing thermal energy utilization by analyzing drying process and operation principle of fluidized bed dryers,in order to guide optimization and upgrade of fluidized bed drying equipment. Through a systematic analysis on drying process and operation principle of fluidized beds,the energy conservation law was adopted to calculate thermal energy of dryers. The thermal energy of fluidized bed dryers is mainly used to make up for thermal consumption of water evaporation (Qw), hot air from outlet equipment (Qe), thermal consumption for heating and drying wet materials (Qm) and heat dissipation to surroundings through hot air pipelines and cyclone separators. Effective measures and major approaches to enhance thermal energy utilization of fluidized bed dryers were to reduce exhaust gas out by the loss of heat Qe, recycle dryer export air quantity of heat, preserve heat for dry towers, hot air pipes and cyclone separators, dehumidify clean air in inlets and reasonably control drying time and air temperature. Such technical parameters such air supply rate, air inlet temperature and humidity, material temperature and outlet temperature and humidity are set and controlled to effectively save energy during the drying process and reduce the production cost.

Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

Energy Technology Data Exchange (ETDEWEB)

Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E. [IVO International Oy, Vantaa (Finland)

1995-12-31

Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

Further development of a mixed-dryer for wood biomass; Sekoituskuivurin jatkokehitys

Energy Technology Data Exchange (ETDEWEB)

Heinonen, O. [Imatran Voima Oy, Vantaa (Finland). Research and Development; Parvio, E [IVO International Oy, Vantaa (Finland)

1996-12-31

Imatran Voima Oy and IVO International Ltd are developing a new, advanced drying method for high moisture content fuels such as peat, biomass, and brown coal. The drying technology is based on using the heat of the fluidized bed directly for drying. The drying takes place at steam atmosphere, which makes it possible to recover the latent heat of evaporation back to process at high temperature level. This improves the thermal efficiency of the plant considerably. The technology is called bed mixing dryer. The pilot plant of the bed mixing dryer was built to IVO`s Kuusamo peat and wood fired power plant that was commissioned in the beginning of 1994. The Kuusamo district heating power plant has a fuel input of 27 MW that gives a power output of 6 MWe and district heat output of 17.5/21.2 MWth. As fuels are used peat, saw dust and wood wastes. The boiler is a bubbling fluidized bed boiler and the steam cycle is a conventional back pressure steam process. The unique feature in the plant is the new dryer that increases the overall thermal efficiency of the plant 10 to 15 units of percentage. In this project the operation and behaviour of the bed mixing dryer has been examined. Various components of the dryer were developed by the cold model tests carried out at IVO`s laboratory in Helsinki. Testing with the Kuusamo bed mixing dryer consisted of about 390 hours of drying tests with peat, bark and saw dust. The dryer operated well, and the drying was effective. The measured final moisture content varied from 7 to 19 % depending on the fuel particle size and the temperature level of the dryer

A thermal analysis for the use of cooled rotating drums in electron processing

International Nuclear Information System (INIS)

Fletcher, P.M.; Williams, K.E.

1988-01-01

The thermal response of rotating drums under an electron beam has been analyzed using a finite difference thermal analysis computer code. Rotating drums are used to convey thin webs or films under the electron beams while controlling their temperature and, in some cases, in dissipating the exotherm involved in curing coatings applied to them. Each portion of the drum surface receives one heat pulse per rotation as it passes under the beam. The drum's thermal behavior shows both an immediate response to each heat pulse and a more gradual response to the average heat acquired over many pulses. After many rotations a steady state is reached where there is only an immediate response to each heat pulse but the gradual heating has tapered off. Nevertheless the steady state temperatures are strongly dependent on the gradual heating that led to them. Slow and fast speeds of rotation are compared showing the effects of both gradual and immediate heating components. The thermal analysis is extended to include the coolant fluid inside the drum shell and the web on the drum surface. The coolant's incoming temperature, volumetric flow rate, flow speed through the coolant channels and film coefficient between the outer shell and fluid are all included in the analysis. The small air gap between the web and drum, the convective cooling of the web to the ambient air, and the exothermic reaction of any chemical reactions on the web are included. The stresses produced in the drum shell (i.e. between the outer surface and the temperature-controlling fluid within the drum) are analyzed in order to define safe e-beam powers and rotating speeds. The analysis provides the basis for many design decisions and can give an end-user a full temperature history for his product for any set of conditions. (author)

Unvented Drum Handling Plan

International Nuclear Information System (INIS)

MCDONALD, K.M.

2000-01-01

This drum-handling plan proposes a method to deal with unvented transuranic drums encountered during retrieval of drums. Finding unvented drums during retrieval activities was expected, as identified in the Transuranic (TRU) Phase I Retrieval Plan (HNF-4781). However, significant numbers of unvented drums were not expected until excavation of buried drums began. This plan represents accelerated planning for management of unvented drums. A plan is proposed that manages unvented drums differently based on three categories. The first category of drums is any that visually appear to be pressurized. These will be vented immediately, using either the Hanford Fire Department Hazardous Materials (Haz. Mat.) team, if such are encountered before the facilities' capabilities are established, or using internal capabilities, once established. To date, no drums have been retrieved that showed signs of pressurization. The second category consists of drums that contain a minimal amount of Pu isotopes. This minimal amount is typically less than 1 gram of Pu, but may be waste-stream dependent. Drums in this category are assayed to determine if they are low-level waste (LLW). LLW drums are typically disposed of without venting. Any unvented drums that assay as TRU will be staged for a future venting campaign, using appropriate safety precautions in their handling. The third category of drums is those for which records show larger amounts of Pu isotopes (typically greater than or equal to 1 gram of Pu). These are assumed to be TRU and are not assayed at this point, but are staged for a future venting campaign. Any of these drums that do not have a visible venting device will be staged awaiting venting, and will be managed under appropriate controls, including covering the drums to protect from direct solar exposure, minimizing of container movement, and placement of a barrier to restrict vehicle access. There are a number of equipment options available to perform the venting. The

Open-loop heat-recovery dryer

Science.gov (United States)

TeGrotenhuis, Ward Evan

2013-11-05

A drying apparatus is disclosed that includes a drum and an open-loop airflow pathway originating at an ambient air inlet, passing through the drum, and terminating at an exhaust outlet. A passive heat exchanger is included for passively transferring heat from air flowing from the drum toward the exhaust outlet to air flowing from the ambient air inlet toward the drum. A heat pump is also included for actively transferring heat from air flowing from the passive heat exchanger toward the exhaust outlet to air flowing from the passive heat exchanger toward the drum. A heating element is also included for further heating air flowing from the heat pump toward the drum.

DESIGN AND THERMAL PERFORMANCE OF THE SOLAR BIOMASS HYBRID DRYER FOR CASHEW DRYING

Directory of Open Access Journals (Sweden)

Saravanan Dhanuskodi

2014-12-01

Full Text Available Drying of Cashew nut to remove testa is one of the most energy-intensive processes of cashew nut process industry. For this reason a hybrid dryer consisting of a solar flat plate collector, a biomass heater and a drying chamber is designed and fabricated. 40 kg of Cashew nut with initial moisture of 9 % is used in the experiment. The performance test of the dryer is carried out in two modes of operation: hybrid-forced convection and hybrid-natural convection. Drying time and drying efficiency during these two modes of operation are estimated and compared with the sun drying. The system is capable of attaining drying temperature between 50º and 70ºC. In the hybrid forced drying, the required moisture content of 3% is achieved within 7 hours and the average system efficiency is estimated as 5.08%. In the hybrid natural drying, the required moisture content is obtained in 9 hours and the average system efficiency is 3.17%. The fuel consumption during the drying process is 0.5 kg/hr and 0.75 kg/hr for forced mode and natural mode, respectively. The drying process in the hybrid forced mode of operation is twice faster than the sun drying. The dryer can be operated in any climatic conditions: as a solar dryer on normal sunny days, as a biomass dryer at night time and as a hybrid dryer on cloudy days. Based on the experimental study, it is concluded that the developed hybrid dryer is suitable for small scale cashew nut farmers in rural areas of developing countries.

Modelling and simulation of processes by smart sensing : a solar dryer for plant material

Energy Technology Data Exchange (ETDEWEB)

Correa, E.C.; Diezma, B.; Ruiz-Altisent, M. [LPF-TAGRALIA Univ. Politecnica, CENIM-CSIC, Madrid (Spain)

2010-07-01

This paper reported on a study in which as small wood dryer was modelled. Studies have shown that properly designed solar dryers may prove to be energy saving devices for drying processes. The drying rate expressed as -dX/dt=f/X (where X is DB wood moisture content), allows to identify 2 different kinetics, notably for high X values or fibre saturation point (FSP) and for X values under FSP, in which diffusion is the mechanism that governs a decreasing drying rate at this stage. The complex drying rate model developed in this study made it possible the determine the wood and convective mass transfer at the wood-air interface. Validation and application to fruit and plant drying cycles is currently underway. Three different proposed models are used in the software for a smart sensor system, which is based on Sensirion sensors for temperature and relative humidity in the air, and thermocouples for timber temperature.

Performance of A Horizontal Cylinder Type Rotary Dryer for Drying Process ofOrganic Compost from Solid Waste Cocoa Pod

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2008-07-01

Full Text Available Cocoa pod husk is the bigest component of cocoa pod, about 70% of total ht of mature pod, and to potentially used as organic compost source. Poten tial solid waste of cocoa pod husk from a cocoa processing centre is about 15— 22 m3/ha/year. A cocoa plantation needs about 20—30 ton/ha/year of organic matters. One of important steps in compos processing technology of cocoa pod solid waste is drying process. Organic compost with 20% moisture content is more easy in handling, application, storage and distribution. Indonesian Coffee and Cocoa Research Institute has designed and tested a horizontal cylinder type rotary dryer for drying process of organic compos from solid waste cocoa pod with kerosene burner as energy sources. The objective of this research is to study performance of a horizontal cylinder type rotary dryer using kerosene burner as energy source for drying process of organic compost from solid waste cocoa pod. The material used was solid waste cocoa pod with 70—75% moisture content (wet basis, 70% size particle larger than 4.76 mm, and 30% size particle less than 4.76 mm, 690—695 kg/m3 bulk density. Drying process temperatures treatment were 60OC, 80OC, and 100OC, and cylinder rotary speed treatments were 7 rpm, 10 rpm, dan 16 rpm. The results showed that dryer had capacity about 102—150 kg/h depend on drying temperature and cylinder rotary speed. Optimum operation condition at 100OC drying temperature, and 10 rpm cylinder rotary speed with drying time to reach final moisture content of 20% was 1,6 h, capacity 136,14 kg/ h, bulk density 410 kg/m3, porocity 45,15%, kerosene consumption as energy source was 2,57 l/h, and drying efficiency 68,34%. Key words : cocoa, drying, rotary dryer, compost, waste

Steam generator with perfected dryers

International Nuclear Information System (INIS)

Fenet, J.C.

1987-01-01

This steam generator has vertically superposed array of steam dryers. These dryers return the steam flow of 180 0 . The return of the water is made by draining channels to the steam production zone [fr

Neutron absorber inserts for 55-gal drums

International Nuclear Information System (INIS)

Wilson, R.E.; Kim, Y.S.; Toffer, H.

2000-01-01

Transport and temporary storage of more than 200 g of fissile material in 55-gal drums at the Rocky Flats Environmental Technology Site (RFETS) have received significant attention during the cleanup mission. This paper discusses successful applications and results of extensive computer studies. Interim storage and movement of fissile material in excess of standard drum limits (200 g) in a safe configuration have been accomplished using special drum inserts. Such inserts have constrained the contents of a drum to two 4-ell bottles. The content of the bottles was limited to 600 g Pu or U in solution or a total of 1200 g for the entire drum. The inserts were a simple design constructed of stainless steel, forming a vertical cylindrical pipe into which two bottles, one on top of the other, could be centered in the drum. The remaining drum volume was configured to preclude any additional bottle placement external to the vertical cylinder. Such inserts in drums were successfully used in moving high-concentration solution from one building to another for chemical processing. Concern about the knowledge of fissile material concentration in bottles prompted another study for drum inserts. The past practice had been to load up to fourteen 4-ell bottles into 55-gal drums, provided the fissile material concentration was < 6 g fissile/ell, and the total drum contents of 200 g fissile was not exceeded. Only one determination of the solution concentration was needed. An extensive safety analysis concluded that a single measurement of bottle content could not ensure compliance with double-contingency-criterion requirements. A second determination of the bottle contents was required before bottles could be placed in a 55-gal drum. Al alternative to a dual-measurement protocol, which is for bolstering administrative control, was to develop an engineered safety feature that would eliminate expensive tests and administrative decisions. A drum insert design was evaluated that would

Multi-shelf domestic solar dryer

International Nuclear Information System (INIS)

Singh, Parm Pal; Singh, Sukhmeet; Dhaliwal, S.S.

2006-01-01

The solar dryer described in this paper can be used for drying various products at home under hygienic conditions with the self guarantee of adulteration free product. This solar dryer is of multi-shelf design, consisting of three perforated trays arranged one above the other. The drying air flows through the product by natural circulation. One of its novel features is variable inclination to capture more solar energy in different seasons. Another novel feature is the option to dry product under shade or without shade as per requirement. The rate of drying is uniform in all the trays due to heating of the air by solar energy in between the trays. The maximum stagnation temperature of this solar dryer was found to be 100 deg. C in the month of November at Ludhiana (31 o N). The moisture evaporation on the 1st, 2nd and 3rd drying day for drying fenugreek leaves was 0.23, 0.18 and 0.038 kg/m 2 h. To overcome the problem of reduction in efficiency on the second and third drying day, a semi-continuous mode of loading has been investigated, in which the efficiency remains almost the same on all drying days. The drying rate in the dryer was more than double that in open shade drying. Moreover, the final moisture content of the product was low enough (7.3% wb) for grinding it to a powder form and for good shelf life (1 year). An uncertainty analysis was performed, and the uncertainty in the efficiency was found to be 1.35%. An economic analysis was performed by three methods. The cost of drying fenugreek leaves in the domestic solar dryer turned out to be about 60% of that in an electric dryer. The cumulative present worth of the savings are much higher (18,316 Rupees) than the capital cost of the dryer (1600 Rupees). The payback period is also very low (<2 years) as compared to the life of the dryer (20 years), so the dryer will dry product free of cost during almost its entire life period. The quality and shelf life of the dried products are comparable to those of

Machine & electrical double control air dryer for vehicle air braking system

Science.gov (United States)

Zhang, Xuan; Yang, Liu; Wang, Xian Yan; Tan, Xiao Yan; Wang, Wei

2017-09-01

As is known to all, a vehicle air brake system, in which usually contains moisture. To solve the problem, it is common to use air dryer to dry compressed air effectively and completely remove the moisture and oil of braking system. However, the existing air dryer is not suitable for all commercial vehicles. According to the operational status of the new energy vehicles in the initial operating period, the structure design principle of the machine & electric control air dryer is expounded from the aspects of the structure and operating principle, research & development process.

Enhancement of Energy Efficiency and Food Product Quality Using Adsorption Dryer with Zeolite

Directory of Open Access Journals (Sweden)

Moh Djaeni

2013-06-01

Full Text Available Drying is a basic operation in wood, food, pharmaceutical and chemical industry. Currently, several drying methods are often not efficient in terms of energy consumption (energy efficiency of 20-60% and have an impact on product quality degradation due to the introduction of operational temperature upper 80oC. This work discusses the development of adsorption drying with zeolite to improve the energy efficiency as well as product quality. In this process, air as drying medium is dehumidified by zeolite. As a result humidity of air can be reduced up to 0.1 ppm. So, for heat sensitive products, the drying process can be performed in low or medium temperature with high driving force. The study has been conducted in three steps: designing the dryer, performing laboratory scale equipment (tray, spray, and fluidised bed dryers with zeolite, and evaluating the dryer performance based on energy efficiency and product quality. Results showed that the energy efficiency of drying process is 15-20% higher than that of conventional dryer. In additon, the dryer can speed up drying time as well as retaining product quality.

Fatigue behaviour of coke drum materials under thermal-mechanical cyclic loading

Directory of Open Access Journals (Sweden)

Jie Chen

2014-01-01

Full Text Available Coke drums are vertical pressure vessels used in the delayed coking process in petroleum refineries. Significant temperature variation during the delayed coking process causes damage in coke drums in the form of bulging and cracking. There were some studies on the fatigue life estimation for the coke drums, but most of them were based on strain-fatigue life curves at constant temperatures, which do not consider simultaneous cyclic temperature and mechanical loading conditions. In this study, a fatigue testing system is successfully developed to allow performing thermal-mechanical fatigue (TMF test similar to the coke drum loading condition. Two commonly used base and one clad materials of coke drums are then experimentally investigated. In addition, a comparative study between isothermal and TMF lives of these materials is conducted. The experimental findings lead to better understanding of the damage mechanisms occurring in coke drums and more accurate prediction of fatigue life of coke drum materials.

Simulation of Hybrid Solar Dryer

International Nuclear Information System (INIS)

Yunus, Y M; Al-Kayiem, H H

2013-01-01

The efficient performance of a solar dryer is mainly depending on the good distribution of the thermal and flow field inside the dryer body. This paper presents simulation results of a solar dryer with a biomass burner as backup heater. The flow and thermal fields were simulated by CFD tools under different operational modes. GAMBIT software was used for the model and grid generation while FLUENT software was used to simulate the velocity and temperature distribution inside the dryer body. The CFD simulation procedure was validated by comparing the simulation results with experimental measurement. The simulation results show acceptable agreement with the experimental measurements. The simulations have shown high temperature spot with very low velocity underneath the solar absorber and this is an indication for the poor design. Many other observations have been visualized from the temperature and flow distribution which cannot be captured by experimental measurements.

Cementitious Spray Dryer Ash-Tire Fiber Material for Maximizing Waste Diversion

Directory of Open Access Journals (Sweden)

Charles E. Riley

2011-01-01

Full Text Available Spray dryer absorber (SDA material, also known as spray dryer ash, is a byproduct of coal combustion and flue gas scrubbing processes that has self-cementing properties similar to those of class C fly ash. SDA material does not usually meet the existing standards for use as a pozzolan in Portland cement concrete due to its characteristically high sulfur content, and thus unlike fly ash, it is rarely put to beneficial use. This paper presents the results of a study with the objective of developing beneficial uses for SDA material in building materials when combined with tire fiber reinforcement originating from a recycling process. Specifically, spray dryer ash was investigated for use as the primary or even the sole binding component in a mortar or concrete. This study differs from previous research in that it focuses on very high contents of spray dryer ash (80 to 100 percent in a hardened product. The overarching objective is to divert products that are normally sent to landfills and provide benefit to society in beneficial applications.

Method of estimating maximum VOC concentration in void volume of vented waste drums using limited sampling data: Application in transuranic waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Connolly, M.J.

1995-01-01

A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds (VOCs) within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles as well as limited waste drum sampling data. The model consists of a series of material balance equations describing steady-state VOC transport from each distinct void volume in the drum. The primary model input is the measured drum headspace VOC concentration. Model parameters are determined or estimated based on available process knowledge. The model effectiveness in estimating VOC concentration in the headspace of the innermost layer of confinement was examined for vented waste drums containing different waste types and configurations. This paper summarizes the experimental measurements and model predictions in vented transuranic waste drums containing solidified sludges and solid waste

40 CFR 1065.342 - Sample dryer verification.

Science.gov (United States)

2010-07-01

...-membrane dryer or thermal chiller. (d) Sample dryer verification procedure. Use the following method to... highest sample water content that you estimate during emission sampling. (3) Introduce the humidified gas... sampling system at a temperature at least 5 °C above the local humidified gas dewpoint. For dryers used in...

CFD Analysis to Calculate the Optimal Air Velocity in Drying Green Tea Process Using Fluidized Bed Dryer

Science.gov (United States)

Yohana, Eflita; Nugraha, Afif Prasetya; Diana, Ade Eva; Mahawan, Ilham; Nugroho, Sri

2018-02-01

Tea processing is basically distinguished into three types which black tea, green tea, and oolong tea. Green tea is processed by heating and drying the leaves. Green tea factories in Indonesia are generally using the process of drying by panning the leaves. It is more recommended to use the fluidization process to speed up the drying process as the quality of the tea can be maintained. Bubbling fluidization is expected to occur in this research. It is a process of bubbles are formed in the fluidization. The effectiveness of the drying process in a fluidized bed dryer machine needs to be improved by using a CFD simulation method to proof that umf < u < ut, where the average velocity value is limited by the minimum and the maximum velocity of the calculation the experimental data. The minimum and the maximum velocity value of the fluidization is 0.96 m/s and 8.2 m/s. The result of the simulation obtained that the average velocity of the upper bed part is 1.81 m/s. From the results obtained, it can be concluded that the calculation and the simulation data is in accordance with the condition of bubbling fluidization in fluidized bed dryer.

Compound drum for a centrifugal separator

International Nuclear Information System (INIS)

1972-01-01

This invention concerns a method for centrifugal separation of UF 6 . The invention provides a composite drum capable of rapid rotation for use in a centrifugal separating arrangement for gaseous materials. The drum is provided with a first drum section comprised of a metal and a second drum section comprised of a fiber-reinforced synthetic material. The second drum section is applied on the outside peripheral surface of the first drum section, where the second drum section is provided with a number of annular components, each of which is shorter than the first drum section

Testing Report: Littleford-Day Dryer Operation: Dryer Operation Impacts of Proposed MIS Mitigation Changes

Energy Technology Data Exchange (ETDEWEB)

Shimskey, Rick W. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Buchmiller, William C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Elmore, Monte R. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2007-06-01

Pacific Northwest National Laboratory performed a series of tests using the Littleford Day 22-liter dryer during investigations that evaluated changes in the melter-feed composition for the Demonstration Bulk Vitrification System. During testing, a new melter-feed formulation was developed that improved dryer performance while improving the retention of waste salts in the melter feed during vitrification.

Control Systems of Rubber Dryer Machinery Components Using Programmable Logic Control (PLC)

Science.gov (United States)

Hendra; Yulianto, A. S.; Indriani, A.; Hernadewita; Hermiyetti

2018-02-01

Application of programmable logic control (PLC) is widely used on the control systems in the many field engineering such as automotive, aviation, food processing and other industries [1-2]. PLC is simply program to control many automatic activity, easy to use, flexible and others. PLC using the ladder program to solve and regulated the control system component. In previous research, PLC was used for control system of rotary dryer machine. In this paper PLC are used for control system of motion component in the rubber dryer machinery. Component of rubber dryer machine is motors, gearbox, sprocket, heater, drying chamber and bearing. Principle working of rubber dryer machinery is wet rubber moving into the drying chamber by sprocket. Sprocket is driven by motors that conducted by PLC to moving and set of wet rubber on the drying chamber. Drying system uses greenhouse effect by making hanger dryer design in the form of line path. In this paper focused on motion control system motors and sensors drying rubber using PLC. The results show that control system of rubber dryer machinery can work in accordance control input and the time required to dry the rubber.

Herbal dryer: drying of ginger (zingiber officinale) using tray dryer

Science.gov (United States)

Haryanto, B.; Hasibuan, R.; Alexander; Ashari, M.; Ridha, M.

2018-02-01

Drying is widely used as a method to preserve food because of its convenience and affordability. Drying of ginger using tray dryer were carried out at various drying conditions, such as air-drying flow, air-drying temperature, and sample dimensions, to achieve the highest drying rate. Samples with various dimensions were placed in the tray dryer and dried using various air-drying flow and temperatures. The weights of samples were observed every 3 minutes interval. Drying was stopped after three times of constant weighing. Data of drying was collected to make the drying curves. Drying curves show that the highest drying rate is achieved using highest air flow and temperature.

Heat-pump tumble dryers; Waermepumpen-Tumbler

Energy Technology Data Exchange (ETDEWEB)

Bluemig, N.; Gatter, R.

2004-07-01

Commonly available tumble dryers with air-vented or condenser systems in combination with electrical heating have a high specific energy consumption and never fulfil the requirements for Energy Label Class A (<= 0.55 kWh/kg.). The development of a tumbler with a heat pump system has enabled a reduction of almost 50% in the specific energy consumption. In addition to ecological aspects, this means that a significant reduction in energy costs is achieved as well as a beneficial effect on room climate. Other considerations taken into account in the development of the 6.5 kg tumbler were: (i) Compact modular design; integration of the heat pump in the appliance casing; (ii) Long operating life without clogging-up of the heat exchanger by fluff; (iii) Stable process throughout the drying in ambient temperatures of up to 35 {sup o}C. Process stability in particular presented a tough challenge. The solution came in the form of an additional booster condenser that prevents overheating of the compressor towards the end of the process when only negligible amounts of energy are being carried away as a result of the low residual moisture in the laundry. It proved possible to reduce the specific power consumption to less than 0.4 kWh/kg and the leak rate to less 30 %. Thanks to the compact, modular design, the heat pump could be integrated in a housing which has the same size as a conventional 6.5 kg dryer. Clogging-up of the heat exchanger surfaces with fluff was prevented by a multi-stage cascade filtration system. With this heat pump dryer it has been possible for the very first time to develop to series production and launch an appliance in the up to 6.5 kg category that not only fulfils the requirements of Energy Label Class A but also offers a serious alternative to conventional tumble dryers thanks to its compact design, operating safety and ease of operation. Future development opportunities lie in more cost-effective production of the heat pump module, shortening of

BWR Steam Dryer Alternating Stress Assessment Procedures

Energy Technology Data Exchange (ETDEWEB)

Morante, R. J. [Brookhaven National Lab. (BNL), Upton, NY (United States); Hambric, S. A. [Brookhaven National Lab. (BNL), Upton, NY (United States); Ziada, S. [Brookhaven National Lab. (BNL), Upton, NY (United States)

2016-12-01

This report presents an overview of Boiling Water Reactor (BWR) steam dryer design; the fatigue cracking failures that occurred at the Quad Cities (QC) plants and their root causes; a history of BWR Extended Power Uprates (EPUs) in the USA; and a discussion of steam dryer modifications/replacements, alternating stress mechanisms on steam dryers, and structural integrity evaluations (static and alternating stress).

Evaluation of overturning capacity of low level radioactive waste drum during earthquake. Part 2. Investigation of drum weight distribution effect and drum columns interaction by numerical analysis

International Nuclear Information System (INIS)

Tochigi, Hitoshi

2011-01-01

Numerical analysis case study is carried out for three layered and four layered low level radioactive waste drums by numerical models based on the results of shaking table test. First of all, numerical analysis results about drums displacement due to uplift and sliding on pallets during earthquake are compared with the experimental results and it is shown good agreement in both results. By this analytical model effects of drum weight distribution along height direction and drum columns interaction followed by each other drum's collisions on overturning capacity during earthquake are researched. From numerical analysis results the limit acceleration which is minimum value of input acceleration at storage building floor when three layered or four layered waste drums overturn is researched. It is shown that overturning capacity during earthquake decline when height of gravity center of three layered and four layered drums get large. So it is available to get down height of gravity center by controlling drum weight distribution along height direction. And as effect of drum columns interaction it is indicated that overturning capacity of single column arrangement drums is larger than that of many columns arrangement drums because phase deference between drum columns occur and decrease vibration amplitude by each other collisions. (author)

GAS DRYER DESIGN FOR VERMICELLI USING MICROCONTROLLER ATMEGA 8535

Directory of Open Access Journals (Sweden)

Akhmad Mufasil

2013-04-01

Full Text Available The purpose of this research is designing a gas dryer for vermicelli using a microcontroller ATmega 8535 that can overcome the obstacles in the drying department. The microcontroller ATmega 8535 used to regulate the temperature of the drying chamber. This tool design is made to compare between conventional dryer and a theoritical gas dryer in the factory. The method used in this paper is field study in the factory. Based on the experience then theoritical gas dryer design from the factory’s datas. A microcontroller Atmega 8535 is added to the dryer to easier the dryer operation. The result of the theoritical gas dryer design for vermicelli using a microcontroller ATmega 8535, showed a faster time drying for 131,04 kg of vermicelli need 47,72 minutes at a temperature of 40- 55° C.

Assessment of differences between products obtained in conventional and vacuum spray dryer

Directory of Open Access Journals (Sweden)

Fernanda de Melo RAMOS

Full Text Available Abstract In this work, an experimental unit of a vacuum spray dryer was built. This prototype attempted to combine the advantages of freeze-drying (drying at low temperatures due to vacuum and spray drying (increase of surface area aiming the improvement of heat transfer efficiency. Maltodextrin solutions were dried in the vacuum operated equipment and in conventional spray dryer. The vacuum spray dryer system allowed obtaining powder at low temperatures due to the lowering of pressure conditions (2-5 kPa inside the drying chamber. The products obtained in the two systems were characterized and compared for particle size distribution, moisture content, water activity, bulk density and solubility in water. The processes yields were also evaluated and compared. The vacuum spray dryer system allowed the production of larger, more soluble and less dense particles than those obtained in the conventional configuration of the equipment, resulting in drier and, therefore, with lower water activity particles. Thus, the use of the vacuum spray dryer as a drying technique may be an alternative for the production of powder rich in thermosensitive compounds.

Investigation of influence of drying agent movement on the drying process effectiveness in the gravitational shelf dryer

Directory of Open Access Journals (Sweden)

N. O. Artyukhova

2017-12-01

Full Text Available The article stands for a research of the drying process efficiency of various approaches of reciprocal movement organization of drying agent and disperse material. It focuses on the results of shelf dryer investigation. The test condition was as follows: backflow of the drying agent and disperse material movement; backflow of the drying agent and disperse material movement with the drying agent recirculation; backflow of the drying agent and disperse material movement with the bypassing of drying agent and it’s putting on separate stage of gravitational shelf dryer. The influence of the drying agent movement organization on the characteristics of disperse material and drying agent, energy costs for this process and its efficiency is shown. The recommendations of usage of represented approaches of flows movement organization depending on the desired final moisture of the material as well as its physical and chemical properties are given. The proposed ways of reciprocal flows movement organization allow to reduce the costs of drying agent heating or to increase the efficiency of moisture removal at constant energy consumption.

Solid waste drum array fire performance

International Nuclear Information System (INIS)

Louie, R.L.; Haecker, C.F.; Beitel, J.J.; Gottuck, D.T.; Rhodes, B.T.; Bayier, C.L.

1995-09-01

Fire hazards associated with drum storage of radioactively contaminated waste are a major concern in DOE waste storage facilities. This report is the second of two reports on fire testing designed to provide data relative to the propagation of a fire among storage drum arrays. The first report covers testing of individual drums subjected to an initiating fire and the development of the analytical methodology to predict fire propagation among storage drum arrays. This report is the second report, which documents the results of drum array fire tests. The purpose of the array tests was to confirm the analytical methodology developed by Phase I fire testing. These tests provide conclusive evidence that fire will not propagate from drum to drum unless an continuous fuel source other than drum contents is provided

Direct measurement of γ-emitting radionuclides in waste drum

International Nuclear Information System (INIS)

Ma Ruwei; Mao Yong; Zhang Xiuzhen; Xia Xiaobin; Guo Caiping; Han Yueqin

1993-01-01

The low-level rad waste produced from nuclear power plant, nuclear facilities, and in the process of their decommissioning is stored in waste depository. For the safety of transport and storage of these wastes, some test must be done. One of them is to analyse the kinds and activities of radionuclides in each waste drum. Segmented scanning gamma spectrum analysis can be used for direct measurement of gamma-emitting radionuclides in drum. Gamma emitters such as Co-60, Cs-137, Ra-226 can be measured directly from outside of drum. A method and system for direct measuring gamma emitters in waste drum are described, and measuring apparatus and measurement results as well

Feasibility analysis of heat pump dryer to dry hawthorn cake

International Nuclear Information System (INIS)

Wang, D.C.; Zhang, G.; Han, Y.P.; Zhang, J.P.; Tian, X.L.

2011-01-01

Highlights: → A heat pump dryer (HPD) is effectively proposed to dry hawthorn cake-likely materials. → Low drying temperature and high COP of heat pump are obtained in drying beginning. → HPD is more effective, economic than a traditional hot air dryer. → Feasibility of the HPD is also validated by the operation economy estimation. - Abstract: A heat pump dryer (HPD) would be an economic, environmentally friendly, hygienic drying machine used to dry some food, such as hawthorn cakes. Based on the production process of the hawthorn cake, a HPD is proposed and its basic principle is introduced. The experimental drying curves of the hawthorn cake using the heat pump drying method and the traditional hot air drying method are compared and analyzed. The drying process of hawthorn cakes is similar to that of the other drying materials. The higher drying temperature causes a faster drying process. But in the initial stage of the heat pump drying process, the water content of the hawthorn cake is not sensitive to the drying temperature, so a lower drying air temperature can be available in order to get a higher coefficient of performance (COP) of the heat pump (HP). The experimental results and the economic analysis indicate that the HPD is feasibly used to dry hawthorn cakes.

Feasibility analysis of heat pump dryer to dry hawthorn cake

Energy Technology Data Exchange (ETDEWEB)

Wang, D.C., E-mail: wdechang@163.com [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China); Zhang, G.; Han, Y.P.; Zhang, J.P.; Tian, X.L. [College of Electromechanical Engineering, Qingdao University, Qingdao 266071 (China)

2011-08-15

Highlights: {yields} A heat pump dryer (HPD) is effectively proposed to dry hawthorn cake-likely materials. {yields} Low drying temperature and high COP of heat pump are obtained in drying beginning. {yields} HPD is more effective, economic than a traditional hot air dryer. {yields} Feasibility of the HPD is also validated by the operation economy estimation. - Abstract: A heat pump dryer (HPD) would be an economic, environmentally friendly, hygienic drying machine used to dry some food, such as hawthorn cakes. Based on the production process of the hawthorn cake, a HPD is proposed and its basic principle is introduced. The experimental drying curves of the hawthorn cake using the heat pump drying method and the traditional hot air drying method are compared and analyzed. The drying process of hawthorn cakes is similar to that of the other drying materials. The higher drying temperature causes a faster drying process. But in the initial stage of the heat pump drying process, the water content of the hawthorn cake is not sensitive to the drying temperature, so a lower drying air temperature can be available in order to get a higher coefficient of performance (COP) of the heat pump (HP). The experimental results and the economic analysis indicate that the HPD is feasibly used to dry hawthorn cakes.

Solar dryer with thermal storage and biomass-backup heater

Energy Technology Data Exchange (ETDEWEB)

Madhlopa, A. [Department of Physics and Biochemical Sciences, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi); Ngwalo, G. [Department of Mechanical Engineering, Malawi Polytechnic, P/Bag 303, Blantyre 3 (Malawi)

2007-04-15

An indirect type natural convection solar dryer with integrated collector-storage solar and biomass-backup heaters has been designed, constructed and evaluated. The major components of the dryer are biomass burner (with a rectangular duct and flue gas chimney), collector-storage thermal mass and drying chamber (with a conventional solar chimney). The thermal mass was placed in the top part of the biomass burner enclosure. The dryer was fabricated using simple materials, tools and skills, and it was tested in three modes of operation (solar, biomass and solar-biomass) by drying twelve batches of fresh pineapple (Ananas comosus), with each batch weighing about 20 kg. Meteorological conditions were monitored during the dehydration process. Moisture and vitamin C contents were determined in both fresh and dried samples. Results show that the thermal mass was capable of storing part of the absorbed solar energy and heat from the burner. It was possible to dry a batch of pineapples using solar energy only on clear days. Drying proceeded successfully even under unfavorable weather conditions in the solar-biomass mode of operation. In this operational mode, the dryer reduced the moisture content of pineapple slices from about 669 to 11% (db) and yielded a nutritious dried product. The average values of the final-day moisture-pickup efficiency were 15%, 11% and 13% in the solar, biomass and solar-biomass modes of operation respectively. It appears that the solar dryer is suitable for preservation of pineapples and other fresh foods. Further improvements to the system design are suggested. (author)

Type B drum packages

International Nuclear Information System (INIS)

McCoy, J.C.

1994-08-01

The Type B drum packages (TBD) are conceptualized as a family of containers in which a single 208 L or 114 L (55 gal or 30 gal) drum containing Type B quantities of radioactive material (RAM) can be packaged for shipment. The TBD containers are being developed to fill a void in the packaging and transportation capabilities of the U.S. Department of Energy as no container packaging single drums of Type B RAM exists offering double containment. Several multiple-drum containers currently exist, as well as a number of shielded casks, but the size and weight of these containers present many operational challenges for single-drum shipments. As an alternative, the TBD containers will offer up to three shielded versions (light, medium, and heavy) and one unshielded version, each offering single or optional double containment for a single drum. To reduce operational complexity, all versions will share similar design and operational features where possible. The primary users of the TBD containers are envisioned to be any organization desiring to ship single drums of Type B RAM, such as laboratories, waste retrieval activities, emergency response teams, etc. Currently, the TBD conceptual design is being developed with the final design and analysis to be completed in 1995 to 1996. Testing and certification of the unshielded version are planned to be completed in 1996 to 1997 with production to begin in 1997 to 1998

Application of Constrained Linear MPC to a Spray Dryer

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2014-01-01

In this paper we develop a linear model predictive control (MPC) algorithm for control of a two stage spray dryer. The states are estimated by a stationary Kalman filter. A non-linear first-principle engineering model is developed to simulate the spray drying process. The model is validated against...... experimental data and able to precisely predict the temperatures, the air humidity and the residual moisture in the dryer. The MPC controls these variables to the target and reject disturbances. Spray drying is a cost-effective method to evaporate water from liquid foods and produces a free flowing powder...

Drum-mate: interaction dynamics and gestures in human-humanoid drumming experiments

Science.gov (United States)

Kose-Bagci, Hatice; Dautenhahn, Kerstin; Syrdal, Dag S.; Nehaniv, Chrystopher L.

2010-06-01

This article investigates the role of interaction kinesics in human-robot interaction (HRI). We adopted a bottom-up, synthetic approach towards interactive competencies in robots using simple, minimal computational models underlying the robot's interaction dynamics. We present two empirical, exploratory studies investigating a drumming experience with a humanoid robot (KASPAR) and a human. In the first experiment, the turn-taking behaviour of the humanoid is deterministic and the non-verbal gestures of the robot accompany its drumming to assess the impact of non-verbal gestures on the interaction. The second experiment studies a computational framework that facilitates emergent turn-taking dynamics, whereby the particular dynamics of turn-taking emerge from the social interaction between the human and the humanoid. The results from the HRI experiments are presented and analysed qualitatively (in terms of the participants' subjective experiences) and quantitatively (concerning the drumming performance of the human-robot pair). The results point out a trade-off between the subjective evaluation of the drumming experience from the perspective of the participants and the objective evaluation of the drumming performance. A certain number of gestures was preferred as a motivational factor in the interaction. The participants preferred the models underlying the robot's turn-taking which enable the robot and human to interact more and provide turn-taking closer to 'natural' human-human conversations, despite differences in objective measures of drumming behaviour. The results are consistent with the temporal behaviour matching hypothesis previously proposed in the literature which concerns the effect that the participants adapt their own interaction dynamics to the robot's.

Heat transfer and energy efficiency in infrared paper dryers

Energy Technology Data Exchange (ETDEWEB)

Pettersson, Magnus

1999-11-01

Infrared (IR) dryers are widely used in the paper industry, mainly in the production of coated paper grades. The thesis deals with various aspects of heat transfer and energy use in infrared heaters and dryers as employed in the paper industry. Both gas-fired and electric IR dryers are considered and compared. The thesis also provides an introduction to infrared heaters and infrared drying, including a review of recent literature in the field. The transport of thermal radiation inside a paper sheet was investigated and different IR dryers were compared in terms of their ability to transfer energy to the internal parts of a paper sheet. Although there were evident differences in the absorption of radiation between gas-fired and electric IR dryers, the distinction was found not to be as important as has generally been believed. The main differences appeared to be due to the choice of a one- or a two-sided dryer solution, rather than the spectral distributions emitted by the dryers. A method for evaluating the radiation efficiency of IR heaters was proposed. An electric IR heater was evaluated in the laboratory. The radiation efficiency of the heater was shown to be strongly dependent on the power level. The maximum efficiency, found at high power level, was close to 60 %. A procedure for evaluation of the total energy transfer efficiency of an infrared paper dryer was proposed and used in the evaluation of an electric IR dryer operating in an industrial coating machine. The efficiency of the dryer was roughly 40 %. A model for an electric IR heater was developed. The model includes non-grey radiative heat transfer between the different parts of the heater, as well as conduction in reflector material and convective cooling of the surfaces. Using IR module voltage as the only input, model predictions of temperatures and heat flux were found to agree well with experimental data both at steady state and under transient conditions. The model was also extended to include

Waste streams that preferentially corrode 55-gallon steel storage drums

International Nuclear Information System (INIS)

Zirker, L.R.; Beitel, G.A.; Reece, C.M.

1995-06-01

When 55-gal steel drum waste containers fail in service, i.e., leak, corrode or breach, the standard fix has been to overpack the drum. When a drum fails and is overpacked into an 83-gal overpack drum, there are several negative consequences. Identifying waste streams that preferentially corrode steel drums is essential to the pollution prevention philosophy that ''an ounce of prevention is worth a pound of cure.'' It is essential that facilities perform pollution prevention measures at the front end of processes to reduce pollution on the back end. If these waste streams can be identified before they are packaged, the initial drum packaging system could be fortified or increased to eliminate future drum failures, breaches, clean-ups, and the plethora of other consequences. Therefore, a survey was conducted throughout the US Department of Energy complex for information concerning waste streams that have demonstrated preferential corrosion of 55-gal steel drums. From 21 site contacts, 21 waste streams were so identified. The major components of these waste streams include acids, salts, and solvent liquids, sludges, and still bottoms. The solvent-based waste streams typically had the shortest time to failure, 0.5 to 2 years. This report provides the results of this survey and research

Two-dimensional mathematical model for simulation of the drying process of thick layers of natural materials in a conveyor-belt dryer

Directory of Open Access Journals (Sweden)

Salemović Duško R.

2017-01-01

Full Text Available This paper presents the mathematical model and numerical analysis of the convective drying process of thick slices of colloidal capillary-porous materials slowly moving through conveyor-belt dryer. A flow of hot moist air was used as drying agent. The drying process has been analyzed in the form of a 2-D mathematical model, in two directions: along the conveyor and perpendicular on it. The mathematical model consists of two non-linear differential equations and one equation with a transcendent character and it is based on the mathematical model developed for drying process in a form of a 1-D thin layer. The appropriate boundary conditions were introduced. The presented model is suitable for the automated control of conveyor-belt dryers. The obtained results with analysis could be useful in predicting the drying kinetics of potato slices and similar natural products.

PERFORMANCE ASSESSMENT OF SOLAR DRYER WITH INDIRECT HEATING

Directory of Open Access Journals (Sweden)

Boryana Brashlyanova

2014-03-01

Full Text Available The performed tests were designed to identify and analyze the parameters of drying in a authors model solar dryer. They to be the basis for constructing of an improved model. Drying was carried out in a pilot model solar dryer with prunes in two cycles. Both samples were run under steady sunshine in outdoor air temperature ranging between 20-22°C in the morning and 33-35°C in the early afternoon hours. Depending on the ambient conditions, the drying temperature was found in the range of 30 to 50°C. The dried samples had a water activity Aw> 0.9, due to which the storage is at -18°C. The duration of the drying process of prunes was inconstant and lasted from 2 to 3 days, depending on the final moisture content of the product and the external temperature, humidity, and intensity of solar radiation. The obtained two products intermediate moisture prunes, in addition to direct human consumption could be used as a base for incorporation into other products. Prunes with intermediate moisture content 40% could be consumed directly at ambient temperature or after freezing and tempering at -6 to -5ºC. Based on the established parameters we are to design and produce an improved solar dryer model that allows better utilization of heat and shortening the process duration.

Solar thermal drum drying performance of prune and tomato pomaces

Science.gov (United States)

Fruit and vegetable pomaces are co-products of the food processing industry; they are underutilized in part because their high water activity (aw) renders them unstable. Drum drying is one method that can dry/stabilize pomaces, but current drum drying methods utilize conventional, high-environmental...

Chipping machines: disc and drum energy requirements

Directory of Open Access Journals (Sweden)

Alessio Facello

2013-09-01

Full Text Available Air pollution and fossil fuel reserves exhaustion are increasing the importance of the biomass-derived products, in particular wood, as source of clean and renewable energy for the production of electricity or steam. In order to improve the global efficiency and the entire production chain, we have to evaluate the energetic aspects linked to the process of transformation, handling and transport of these materials. This paper reports results on a comparison between two chippers of similar size using different cutting technology: disc and drum tool respectively. During trials, fuel consumption, PTO torque and speed, processing time and weight of processed material were recorded. Power demand, fuel consumption, specific energy and productivity were computed. The machine was fed with four different feedstock types (chestnut logs, poplar logs, poplar branches, poplar sawmill residues. 15 repetitions for each combination of feedstock-tool were carried out. The results of this study show that the disc tool requires, depending on the processed material, from 12 to 18% less fuel per unit of material processed than the drum tool, and consequently, from 12 to 16% less specific energy. In particular, the highest difference between tools was found in branches processing whereas the smallest was in poplar logs. Furthermore the results of the investigation indicate, that, in testing conditions, the productivity of drum tool is higher (8% than disc tool.

Research Based on the Acoustic Emission of Wind Power Tower Drum Dynamic Monitoring Technology

Science.gov (United States)

Zhang, Penglin; Sang, Yuan; Xu, Yaxing; Zhao, Zhiqiang

Wind power tower drum is one of the key components of the wind power equipment. Whether the wind tower drum performs safety directly affects the efficiency, life, and performance of wind power equipment. Wind power tower drum in the process of manufacture, installation, and operation may lead to injury, and the wind load and gravity load and long-term factors such as poor working environment under the action of crack initiation or distortion, which eventually result in the instability or crack of the wind power tower drum and cause huge economic losses. Thus detecting the wind power tower drum crack damage and instability is especially important. In this chapter, acoustic emission is used to monitor the whole process of wind power tower drum material Q345E steel tensile test at first, and processing and analysis tensile failure signal of the material. And then based on the acoustic emission testing technology to the dynamic monitoring of wind power tower drum, the overall detection and evaluation of the existence of active defects in the whole structure, and the acoustic emission signals collected for processing and analysis, we could preliminarily master the wind tower drum mechanism of acoustic emission source. The acoustic emission is a kind of online, efficient, and economic method, which has very broad prospects for work. The editorial committee of nondestructive testing qualification and certification of personnel teaching material of science and technology industry of national defense, "Acoustic emission testing" (China Machine Press, 2005.1).

Performance of a Big Scale Green House Type Dryer for Coffee Drying Process

Directory of Open Access Journals (Sweden)

Sukrisno Widyotomo

2014-12-01

Full Text Available Dying is one of important steps in coffee processing to produce good quality. Greenhouse is one of artificial drying alternatives that potential for coffee drying method cause of cleans environmental friendly, renewable energy sources and chippers. Indonesian Coffee and Cocoa Research Institute has developed and testing a big scale greenhouse type dryer for fresh coffee cherries and wet parchment coffee drying process. Greenhouse has 24 m length, 18 m width, also 3 m high of the front side and 2 m high of the rear side. The maximum capacity of greenhouse is 40 tons fresh coffee cherries. Fiber Reinforced Plastic (FRP used as greenhouse roof that combined with I and C profile of steel. Fresh coffee cherries and wet parchment coffee from Robusta variety use as main materials in this research. The treatment of this research was 30 kg/m2, 60 kg/m2 and 90 kg/m2 for coffee density. String process has done by manual, two times a day in the morning and in the afternoon. As control, fresh coffee cherries and wet parchment coffee has dried by fully sun drying method. The result showed that a big scale greenhouse has heat drying efficiency between 29.9-58.2% depend on type and density of coffee treatments. On the full sunny day, greenhouse has produced maximum drying air temperature up to 52oC. In radiation cumulative level 4-5 kW-jam/m2 per day, 12.9-38.8 tons fresh coffee cherries or wet parchment coffee with 58-64% moisture content can be dried to 12% moisture content for 6 up to 14 days drying process. Slowly drying mechanism can be avoided negative effect to degradation of quality precursor compound. Capacity of the dryer can be raise and fungi can be reduce with application of controllable mechanical stirring in the greenhouse. Keywords: greenhouse, coffee, drying, quality

COMMERCIAL DEMONSTRATION OF THE MANUFACTURED AGGREGATE PROCESSING TECHNOLOGY UTILIZING SPRAY DRYER ASH

Energy Technology Data Exchange (ETDEWEB)

Roy Scandrol

2003-10-01

Universal Aggregates, LLC proposes to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the Universal Aggregates share is $12.3 (63%). The project team consists of CONSOL Energy Inc., P.J. Dick, Inc., SynAggs, LLC, and Universal Aggregates, LLC. The Birchwood Facility will transform 115,000 tons per year of spray dryer by-products that are currently being disposed of in an offsite landfill into 167,000 tons of a useful product, lightweight aggregates that can be used to manufacture lightweight aggregates that can be used to manufacture lightweight and medium weight masonry blocks. In addition to the environmental benefits, the Birchwood Facility will create nine (9) manufacturing jobs plus additional employment in the local trucking industry to deliver the aggregate to customers or reagents to the facility. A successful demonstration would lead to additional lightweight aggregate manufacturing facilities in the United States. There are currently twenty-one (21) spray dryer facilities operating in the United States that produce an adequate amount of spray dryer by-product to economically justify the installation of a lightweight aggregate manufacturing facility. Industry sources believe that as additional scrubbing is required, dry FGD technologies will be the technology of choice. Letters from potential lightweight aggregate customers indicate that there is a market for the product once the commercialization barriers are eliminated by this demonstration project.

COMMERCIAL DEMONSTRATION OF THE MANUFACTURED AGGREGATE PROCESSING TECHNOLOGY UTILIZING SPRAY DRYER ASH

Energy Technology Data Exchange (ETDEWEB)

Roy Scandrol

2003-04-01

Universal Aggregates, LLC proposes to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the Universal Aggregates share is $12.3 (63%). The project team consists of CONSOL Energy Inc., P.J. Dick, Inc., SynAggs, LLC, and Universal Aggregates, LLC. The Birchwood Facility will transform 115,000 tons per year of spray dryer by-products that are currently being disposed of in an offsite landfill into 167,000 tons of a useful product, lightweight aggregates that can be used to manufacture lightweight aggregates that can be used to manufacture lightweight and medium weight masonry blocks. In addition to the environmental benefits, the Birchwood Facility will create eight (8) manufacturing jobs plus additional employment in the local trucking industry to deliver the aggregate to customers or reagents to the facility. A successful demonstration would lead to additional lightweight aggregate manufacturing facilities in the United States. There are currently twenty-one (21) spray dryer facilities operating in the United States that produce an adequate amount of spray dryer by-product to economically justify the installation of a lightweight aggregate manufacturing facility. Industry sources believe that as additional scrubbing is required, dry flue gas desulfurization (FGD) technologies will be the technology of choice. Letters from potential lightweight aggregate customers indicate that there is a market for the product once the commercialization barriers are eliminated by this demonstration project.

Evaluation of a dryer in a steam generator

International Nuclear Information System (INIS)

Xue Yunkui; Liu Shixun; Guandao, Xie; Chen Junliang

1998-01-01

The hooked-vane-type dryer is used in vertical, natural circulation steam generators used in PWR-type nuclear power stations. it separates the fine droplets of water carried by steam so that the steam generator outlet steam moisture is below 0.25%. Such low moisture is demanded to ensure a safe and economic operation of the unit. The dryer is composed of hooked vanes and a draining structure. A series of tests to screen different designs were performed using air-water mixture. The paper presents the results of the investigation of the effect of the number of drainage hooks , the bending angle , distance between two adjacent vanes, and other geometrical parameters on the performance of a hooked-vane-type steam dryer. It indicates that the dryer still works effectively when the moisture of the steam at the dryer inlet changes in a wide range, and that the performance of the dryer is closely related to the geometry of the draining structure . On the basis of the results of this program, a draining structure with an original design was selected and it is presented in the paper. The performance of the selected draining structure is better than that of similar structures in China and abroad. (author)

Seismic behavior analysis of piled drums

International Nuclear Information System (INIS)

Aoki, H.; Kosaka, T.; Mizushina, T.; Shimizu, M.; Uji, S.; Tsuchiya, H.

1987-01-01

In general, low level radioactive waste is packed in drums and stored in a warehouse being piled vertically, or laid horizontally. To observe the behavior of piled drums during an earthquake, an experimental study was reported. The experimental study is limited by the vibrating platform capacity. To carry out these tests up to the supporting limit is not recommended, in view of the vibrating platform curing as well as the operators' security. It is very useful to develop the analytical method for simulating the behavior of the drums. In this report, a computer program of piled drum's dynamic motion is shown, and the analytical result is referred to the experimental result. From the result of experiment on piled drums, the sliding effect has been found to be very important for the stability of drum, and the rocking motion observed, showing a little acceleration is less than the static estimated value. Behavior of piled drums is a complex phenomena comprising of sliding, rocking and jumping

Learning sustainability by developing a solar dryer for microalgae retrieval

Directory of Open Access Journals (Sweden)

Benedita Malheiro

2016-01-01

Full Text Available Excessive fossil fuel consumption is driving the search for alternative energy production solutions and, in particular, for sustainable sources of energy such as microalgae, from which biodiesel, among other useful compounds, can be obtained. After producing the microalgae, they must be harvested and dried. Existing drying solutions consume too much energy and are, therefore, expensive and unsustainable. The goal of this EPS@ISEP Spring 2013 project was to develop a solar microalgae dryer for the microalgae laboratory of ISEP. A multinational team of five students from distinct fields of study was responsible for designing and building the solar microalgae dryer prototype. The prototype includes a control system to ensure that the microalgae are not destroyed during the drying process. The solar microalgae dryer works as a distiller, extracting the excess water from the microalgae suspension. This paper details the design steps, the building technologies, the ethical and sustainable concerns and compares the prototype with existing solutions. The proposed sustainable microalgae drying process is competitive as far as energy usage is concerned. Finally, the project contributed to increase the team’s sustainable development awareness, active learning and motivation.

Automation of a measurement systems of waste drum alpha activity

International Nuclear Information System (INIS)

Labarre, S.; Bardy, N.

1985-10-01

The alpha radiator activity in the two-hundred liter waste drums is found by an IN96, computerized analyzer of the society Intertechnique, from data delivered by a gamma detector (GeHP) and by neutron detection blocks (He counter). This computerized analyzer manages not only the drum rotation and position in front of the detector, but also the experimental data monitoring and their processing from specific programs (background noise, calibration, drum measurements). Thanks to this automation, the measurement number and their reliability are optimized [fr

Affordable Hybrid Heat Pump Clothes Dryer

Energy Technology Data Exchange (ETDEWEB)

TeGrotenhuis, Ward E. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Butterfield, Andrew [Jabil, St. Petersburg, FL (United States); Caldwell, Dustin D. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Crook, Alexander [Jabil, St. Petersburg, FL (United States)

2016-06-30

This project was successful in demonstrating the feasibility of a step change in residential clothes dryer energy efficiency by demonstrating heat pump technology capable of 50% energy savings over conventional standard-size electric dryers with comparable drying times. A prototype system was designed from off-the-shelf components that can meet the project’s efficiency goals and are affordable. An experimental prototype system was built based on the design that reached 50% energy savings. Improvements have been identified that will reduce drying times of over 60 minutes to reach the goal of 40 minutes. Nevertheless, the prototype represents a step change in efficiency over heat pump dryers recently introduced to the U.S. market, with 30% improvement in energy efficiency at comparable drying times.

Design, development and performance testing of a new natural convection solar dryer

Energy Technology Data Exchange (ETDEWEB)

Pangavhane, D.R. [K.K. Wagh College of Engineering, Nashik (India). Department of Mechanical Engineering; Sawhney, R.L.; Sarsavadia, P.N. [Devi Ahilya Vishwa Vidhyalaya, Indore (India). School of Energy and Environmental Studies

2002-06-01

Mechanical drying of agricultural products is an energy consuming operation in the post-harvesting technology. Greater emphasis is given to using solar energy sources in this process due to the high prices and shortages of fossil fuels. For these purposes, a new natural convection solar dryer consisting of a solar air heater and a drying chamber was developed. This system can be used for drying various agricultural products like fruits and vegetables. In this study, grapes were successfully dried in the developed solar dryer. The qualitative analysis showed that the traditional drying, i.e. shade drying and open sun drying, dried the grapes in 15 and 7 days respectively, while the solar dryer took only 4 days and produced better quality raisins. (author)

CFD analysis for greenhouse effect solar dryer

International Nuclear Information System (INIS)

Wulandani, D.; Abdullah, K.; Hartulistiyoso, E.; Siswantara, I.

2006-01-01

Greenhouse Effect (GHE) solar dryer is a transparent wall structure, consists of absorber plate as solar heat collector, product holders (tray or batch) and fans to discharge moisture from the product. GHE solar dryer is one of the alternative dryer for the farmer and merchants to improve the quality of dried products. Direct sun drying is still popular choice by farmers because it is cheap and simple. However, the method is greatly dependent on the existence of solar irradiation and the product is contaminated very easily by pollution and dirt. The general constraint in designing artificial dryer is the problem of non-uniformity of final moisture content of product, especially for the cabinet of rack type dryer. This condition can be solved by providing uniform distribution of temperature, relative humidity (RH) and airflow velocity of the drying air. Therefore, in this study, such problem was approached by conducting flow simulation within the drying structure by using computational fluid dynamics (CFD) technology to determine the proper position of drying air inlet and outlet, location and capacity of the heat exchanger unit, the position and the capacity of the fan, to produce uniform distribution of the drying air temperature, RH and airflow velocity within the drying chamber.(Author)

Numerical analysis on centrifugal compressor with membrane type dryer

Science.gov (United States)

Razali, M. A.; Zulkafli, M. F.; Mat Isa, N.; Subari, Z.

2017-09-01

Moisture content is a common phenomenon in industrial processes especially in oil and gas industries. This contaminant has a lot of disadvantages which can lead to mechanical failure DEC (Deposition, Erosion & Corrosion) problems. To overcome DEC problem, this study proposed to design a centrifugal compressor with a membrane type dryer to reduce moisture content of a gas. The effectiveness of such design has been analyzed in this study using Computational Fluid Dynamics (CFD) approach. Numerical scheme based on multiphase flow technique is used in ANSYS Fluent software to evaluate the moisture content of the gas. Through this technique, two kind of centrifugal compressor, with and without membrane type dryer has been tested. The results show that the effects of pressure on dew point temperature of the gas change the composition of its moisture content, where high value lead more condensation to occur. However, with the injection of cool dry gas through membrane type dryer in the centrifugal compressor, the pressure and temperature of moisture content as well as mass fraction of H2O in centrifugal compressor show significant reduction.

A dedicated on-line detecting system for auto air dryers

Science.gov (United States)

Shi, Chao-yu; Luo, Zai

2013-10-01

According to the correlative automobile industry standard and the requirements of manufacturer, this dedicated on-line detecting system is designed against the shortage of low degree automatic efficiency and detection precision of auto air dryer in the domestic. Fast automatic detection is achieved by combining the technology of computer control, mechatronics and pneumatics. This system can detect the speciality performance of pressure regulating valve and sealability of auto air dryer, in which online analytical processing of test data is available, at the same time, saving and inquiring data is achieved. Through some experimental analysis, it is indicated that efficient and accurate detection of the performance of auto air dryer is realized, and the test errors are less than 3%. Moreover, we carry out the type A evaluation of uncertainty in test data based on Bayesian theory, and the results show that the test uncertainties of all performance parameters are less than 0.5kPa, which can meet the requirements of operating industrial site absolutely.

Development of nuclear waste concrete drum

International Nuclear Information System (INIS)

Wen Yinghui

1995-06-01

The raw materials selection and the properties for nuclear waste concrete drum, the formula and properties of the concrete, the specification and technical quality requirement of the drum were described. The manufacture essentials and technology, the experiments and checks as well as the effective quality control and quality assurance carried out in the course of production were presented. The developed nuclear waste drum has a simple structure, easily available raw materials and rational formula for concrete. The compressive strength of the drum is more than 70 MPa, the tensile strength is more than 5 MPa, the nitrogen permeability is (2.16∼3.6) x 10 -18 m 2 . The error of the drum in dimensions is +-2 mm. The external surface of the drum is smooth. The drum accords with China standards in the sandy surface, void and crack. The results shows China has the ability to develop and manufacture nuclear waste concrete container and lays the foundation for standardization and series of the nuclear waste container for packing and transporting nuclear wastes in China. (5 figs., 10 tabs.)

Steam drums

International Nuclear Information System (INIS)

Crowder, R.

1978-01-01

Steam drums are described that are suitable for use in steam generating heavy water reactor power stations. They receive a steam/water mixture via riser headers from the reactor core and provide by means of separators and driers steam with typically 0.5% moisture content for driving turbines. The drums are constructed as prestressed concrete pressure vessels in which the failure of one or a few of the prestressing elements does not significantly affect the overall strength of the structure. The concrete also acts as a radiation shield. (U.K.)

The eigenspectra of Indian musical drums.

Science.gov (United States)

Sathej, G; Adhikari, R

2009-02-01

In a family of drums used in the Indian subcontinent, the circular drum head is made of material of nonuniform density. Remarkably, and in contrast to a circular membrane of uniform density, the low eigenmodes of the nonuniform membrane are harmonic. In this work the drum head is modeled as a nonuniform membrane whose density varies smoothly between two prescribed values. The eigenmodes and eigenvalues of the drum head are obtained using a high-resolution numerical method. The mathematical model and the numerical method are able to handle both concentric and eccentric nonuniformities, which correspond, respectively, to the dayan and the bayan drums. For a suitable choice of parameters, which are found by optimizing the harmonicity of the drum, the eigenspectra obtained from the model are in excellent agreement with experiment. The model and the numerical method should find application in numerical sound synthesis.

29 CFR 1915.173 - Drums and containers.

Science.gov (United States)

2010-07-01

... 29 Labor 7 2010-07-01 2010-07-01 false Drums and containers. 1915.173 Section 1915.173 Labor... Vessels, Drums and Containers, Other Than Ship's Equipment § 1915.173 Drums and containers. (a) Shipping drums and containers shall not be pressurized to remove their contents. (b) A temporarily assembled...

Performance of modified greenhouse dryer with thermal energy storage

Directory of Open Access Journals (Sweden)

Om Prakash

2016-11-01

Full Text Available In this attempt, the main goal is to do annual performance, environomical analysis, energy analysis and exergy analysis of the modified greenhouse dryer (MGD operating under active mode (AM and passive mode (PM. Thermal storage is being applied on the ground of MGD. It is applied in three different ways namely barren floor, floor covered with black PVC sheet (PVC and Black Coated. Experimental study of dryers in no-load conditions reveals that floor covered with a black PVC sheet is more conducive for drying purpose than other floors. The MGD under AM is found to be more effective as compared to PM for tomato and capsicum, which are high moisture content crops. For medium moisture content crop (potato chips, both dryers show relatively similar drying performance. Crops dried inside the greenhouse dryer are found to be more nutrient than open sun dried crops. The payback period of the modified greenhouse dryer under passive mode is found to be 1.11 years. However, for the active mode of the modified greenhouse dryer is only 1.89 years. The embodied energy of the passive mode of the dryer is a 480.277 kWh and 628.73 kWh for the active mode of the dryer. The CO2 emissions per annum for passive and active mode greenhouse dryers are found to be 13.45 kg and 17.6 kg respectively. The energy payback time, carbon mitigation and carbon credit have been calculated based type of crop dried. The range of exergy efficiency is 29%–86% in MGD under PM and 30%–78% in the MGD under AM. The variation of Heat utilization factor (HUF for MGD under PM is 0.12–0.38 and 0.26–0.53 for MGD under AM. The range of co-efficient of performances (COP for MGD under PM is 0.55–0.87 and 0.58–0.73 for MGD under AM.

FIFTY-FIVE GALLON DRUM STANDARD STUDY

International Nuclear Information System (INIS)

Puigh, R.J.

2009-01-01

Fifty-five gallon drums are routinely used within the U.S. for the storage and eventual disposal of fissionable materials as Transuranic or low-level waste. To support these operations, criticality safety evaluations are required. A questionnaire was developed and sent to selected Endusers at Hanford, Idaho National Laboratory, Lawrence Livermore National Laboratory, Oak Ridge and the Savannah River Site to solicit current practices. This questionnaire was used to gather information on the kinds of fissionable materials packaged into drums, the models used in performing criticality safety evaluations in support of operations involving these drums, and the limits and controls established for the handling and storage of these drums. The completed questionnaires were reviewed and clarifications solicited through individual communications with each Enduser to obtain more complete and consistent responses. All five sites have similar drum operations involving thousands to tens of thousands of fissionable material waste drums. The primary sources for these drums are legacy (prior operations) and decontamination and decommissioning wastes at all sites except Lawrence Livermore National Laboratory. The results from this survey and our review are discussed in this paper

Vapor generator steam drum spray heat

International Nuclear Information System (INIS)

Fasnacht, F.A. Jr.

1978-01-01

A typical embodiment of the invention provides a combination feedwater and cooldown water spray head that is centrally disposed in the lower portion of a nuclear power plant steam drum. This structure not only discharges the feedwater in the hottest part of the steam drum, but also increases the time required for the feedwater to reach the steam drum shell, thereby further increasing the feedwater temperature before it contacts the shell surface, thus reducing thermal shock to the steam drum structure

Development and performance evaluation of a locally fabricated portable solar tunnel dryer for drying of fruits, vegetables and medicinal plants

International Nuclear Information System (INIS)

Munir, A.; Sultan, U.; Iqbal, M.

2013-01-01

The research was conducted to fabricate and develop a portable solar tunnel dryer (STD) for the drying of fruits, vegetables and medicinal plants. The system was designed as a portable system for decentralized applications at various sites to satisfy the drying requirements of small farmers and co-operatives. The cross sectional area of the solar tunnel dryer was trapezoidal in shape having 0.254 m/sup 2/ face area, with length and width of three meters and one meter respectively. It comprises a collector section (1.35 m) long and a drying section (1.65 m long) and two PV powered DC fans to provide the required air flow rate over the perishable agricultural products to be dried. Transparent polythene cover was used to close the dryer on top side to maintain the steady state air flow within the dryer. It has been observed that the drying air temperature was easily raised by some 8-14 degree C above the ambient temperature at air velocity ranges 0-1 m s/sup -1/. The efficiency of the solar tunnel dryer was found to be 40-45%. Psychrometric analysis was also carried out within the dryer and the process curves were drawn. The process curves were found similar to a conventional dryer showing that this dryer can be successfully utilized for the drying of agricultural products using solar energy. (author)

Influence of the process control on the thermal energy requirement of convection dryers in the brick industry; Einfluss der Prozessfuehrung auf den thermischen Energiebedarf von Konvektionstrocknern in der Ziegelindustrie

Energy Technology Data Exchange (ETDEWEB)

Tretau, Anne

2008-06-10

Brick manufacturing demands high amount of energy. The energy flow analysis inside the brick factory shows that the convective drying of green bricks consumes more than half of the total thermal energy required for brick manufacturing. Therefore this paper deals with the theoretical analysis and investigation for the energy requirement of green bricks. For this, a physical-based model has been developed, which describes the dependence of drying-kinetics as well as the energy-requirement interims of the process parameter like mass of the supply air. It turns out that the specific energy requirement substantially depends on temperature and humidity of the ambience air and also supply air mass flow and its temperature. Due to the continuous temperature rise of the green bricks during the second drying section the specific energy requirement increases significantly with the progressive motion of the drying in a chamber dryer. This is due to the fact that the green brick as well as the air conditioning distance more and more from the cooling limit. Just a low part of the dryer exhaust air is saturated. The exhaust air is continuously sucked out and the green bricks are pulled inside the dryer. So the exhaust air has a relatively higher water saturation. On general, continuous dryers have a lower energy requirement than chamber dryer. For the both types of dryers, the mathematical model shows that the increasing of the supply air temperature combined with a commensurate subsidence of supply air mass flow, results in a reduction of drying energy requirement. The change of other essential parameters of drying like green brick thickness, and density as well as the moisture diffusion coefficient, and the vapour diffusity which are only important in the second drying section are of comparatively negligible effect. The developed mathematical model is successfully implemented for the energy investigation in the industrial dryers. The increase in supply air temperature results

Drum of storing fuel assemblies of nuclear reactor

International Nuclear Information System (INIS)

Artemiev, L.N.; Batjukov, V.I.; Fadeev, A.I.

1979-01-01

The proposed drum for storing fuel assemblies of a nuclear reactor comprises a holder rotatable around its axis and provided with tubular sockets arranged in concentric rows along the circumference of the holder so that the axis of at least one socket of each row intersects the trajectory described by the grip of the recharging mechanism in the course of its movement. The proposed drum design makes it possible to facilitate and speed up the process of recharging fuel asemblies

Silk cocoon drying in forced convection type solar dryer

International Nuclear Information System (INIS)

Singh, Panna Lal

2011-01-01

The thin layer silk cocoon drying was studied in a forced convection type solar dryer. The drying chamber was provided with several trays on which the cocoons loaded in thin layer. The hot air generated in the solar air heater was forced into drying chamber to avoid the direct exposure of sunlight and UV radiation on cocoons. The drying air temperature varied from 50 to 75 o C. The cocoon was dried from the initial moisture content of about 60-12% (wb). The drying data was fitted to thin layer drying models. Drying behaviour of the silk cocoon was best fitted with the Wang and Singh drying model. Good agreement was obtained between predicted and experimental values. Quality of the cocoons dried in the solar dryer was at par with the cocoons dried in the conventional electrical oven dryer in term of the silk yield and strength of the silk. Saving of electrical energy was about 0.75 kWh/kg cocoons dried. Economic analysis indicated that the NPV of the solar dryer was higher and more stable (against escalation rate of electricity) as compare to the same for electrical oven dryer. Due to simplicity in design and construction and significant saving of operational electrical energy, solar cocoon dryer seems to be a viable option.

Complementary Therapy for Addiction: “Drumming Out Drugs”

Science.gov (United States)

Winkelman, Michael

2003-01-01

Objectives. This article examines drumming activities as complementary addiction treatments and discusses their reported effects. Methods. I observed drumming circles for substance abuse (as a participant), interviewed counselors and Internet mailing list participants, initiated a pilot program, and reviewed literature on the effects of drumming. Results. Research reviews indicate that drumming enhances recovery through inducing relaxation and enhancing theta-wave production and brain-wave synchronization. Drumming produces pleasurable experiences, enhanced awareness of preconscious dynamics, release of emotional trauma, and reintegration of self. Drumming alleviates self-centeredness, isolation, and alienation, creating a sense of connectedness with self and others. Drumming provides a secular approach to accessing a higher power and applying spiritual perspectives. Conclusions. Drumming circles have applications as complementary addiction therapy, particularly for repeated relapse and when other counseling modalities have failed. PMID:12660212

DEVELOPMENT OF VACUUM SUBLIMATION DRYERS USING THERMOELECTRIC MODULES

Directory of Open Access Journals (Sweden)

R. A. Barykin

2014-01-01

Full Text Available Summary. The main directions of use of freeze-dryed products and ingredients are revealed. The analysis of sales markets of freeze-dryed products is provided. It is shown that introduction of innovative production technologies will allow to develop dynamically not only to the large companies, but also small firms that will create prerequisites for growth of the Russian market of freeze-dryed products. Tendencies of development of the freeze-drying equipment are analysed. Relevance of development of energy saving freeze-dryers is proved The integrated approach to creation of competitive domestic technologies and the equipment for sublimation dehydration of thermolabile products consists in use of the effective combined remedies of a power supply, a process intensification, reduction of specific energy consumption and, as a result, decrease in product cost at achievement of high quality indicators. Advantages of thermoelectric modules as alternative direction to existing vapor-compression and absorbing refrigerating appliances are given. Researches of process of freeze-drying dehydration with use of thermoelectric modules are conducted. It is scientifically confirmed, that the thermoelectric module working at Peltier effect, promotes increase in refrigerating capacity due to use of the principle of the thermal pump. Options of use of thermoelectric modules in designs of dryers are offered. Optimum operating modes and number of modules in section are defined. Ways of increase of power efficiency of freeze-dryers with use of thermoelectric modules are specified. The received results will allow to make engineering calculations and design of progressive freeze-drying installations with various ways of a power supply.

Development of an Active Solar Crop Dryer: Design Analysis and Performance Evaluation

International Nuclear Information System (INIS)

Itodo, I. N.; Adewole, A.M.; Edemaku, S.K.

2002-01-01

A forced convection indirect solar dryer powered by a PVC module was designed and evaluated. The performance of the dryer was poor; its drying rate, collector and system drying efficiency were 0.74 kg/day, 12% and 10% respectively. The dryer was redesigned and modified into a direct forced convection type- Its design analysis and performance evaluation was undertaken by drying mashed cassava. The drying rate, system drying collector and pick-up efficiencies were 1,6 kg/day (14%/day), 9%, 46% and 29% respectively. Comparatively, the drying rate for sun drying was 0.9 kg/day. The collector efficiency compared very well to the designed value of 48% and may not need further improvement. The pick-up efficiency also compared well with typical averages for this dryer type. The drying rate and system drying efficiency Indicate the need for further development of this dryer. Prediction equations were developed from the results of measured differences in collector, dryer and ambient air temperatures plotted on graphs and applying regression. It is recommended that the volumetric air-flow rate across the drying unit should he improved by affecting the tan speed and air inlet area of the dryer. The improved dryer will subsequently be compared to a natural convection dryer so that an appropriate dryer technology can be recommended for the rural small-scale farmers

Design and performance evaluation of a new hybrid solar dryer for banana

International Nuclear Information System (INIS)

Amer, B.M.A.; Hossain, M.A.; Gottschalk, K.

2010-01-01

A hybrid solar dryer was designed and constructed using direct solar energy and a heat exchanger. The dryer consists of solar collector, reflector, heat exchanger cum heat storage unit and drying chamber. The drying chamber was located under the collector. The dryer was operated during normal sunny days as a solar dryer, and during cloudy day as a hybrid solar dryer. Drying was also carried out at night with stored heat energy in water which was collected during the time of sun-shine and with electric heaters located at water tank. The efficiency of the solar dryer was raised by recycling about 65% of the drying air in the solar dryer and exhausting a small amount of it outside the dryer. Under Mid-European summer conditions it can raise up the air temperature from 30 to 40 deg. C above the ambient temperature. The solar dryer was tested for drying of ripe banana slices. The capacity of the dryer was to dry about 30 kg of banana slices in 8 h in sunny day from an initial moisture content of 82% to the final moisture content of 18% (wb). In the same time it reduced to only 62% (wb) moisture content in open sun drying method. The colour, aroma and texture of the solar dried products were better than the sun drying products.

21 CFR 886.1200 - Optokinetic drum.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Optokinetic drum. 886.1200 Section 886.1200 Food and Drugs FOOD AND DRUG ADMINISTRATION, DEPARTMENT OF HEALTH AND HUMAN SERVICES (CONTINUED) MEDICAL... optokinetic drum is a drum-like device covered with alternating white and dark stripes or pictures that can be...

Contamination control aspects of attaching waste drums to the WIPP Waste Characterization Chamber

International Nuclear Information System (INIS)

Rubick, L.M.; Burke, L.L.

1998-01-01

Argonne National Laboratory West (ANL-W) is verifying the characterization and repackaging of contact-handled transuranic (CH-TRU) mixed waste in support of the Waste Isolation Pilot Program (WIPP) project located in Carlsbad, New Mexico. The WIPP Waste Characterization Chamber (WCC) was designed to allow opening of transuranic waste drums for this process. The WCC became operational in March of 1994 and has characterized approximately 240 drums of transuranic waste. The waste drums are internally contaminated with high levels of transuranic radionuclides. Attaching and detaching drums to the glove box posed serious contamination control problems. Prior to characterizing waste, several drum attachment techniques and materials were evaluated. An inexpensive HEPA filter molded into the bagging material helps with venting during detachment. The current techniques and procedures used to attach and detach transuranic waste drums to the WCC are described

Assessment of the bacterial contamination of hand air dryer in washrooms.

Science.gov (United States)

Alharbi, Sulaiman Ali; Salmen, Saleh Hussein; Chinnathambi, Arunachalam; Alharbi, Naiyf S; Zayed, M E; Al-Johny, Bassam O; Wainwright, Milton

2016-03-01

The present study was carried out, using standard techniques, to identify and count the bacterial contamination of hand air dryers, used in washrooms. Bacteria were isolated from the air flow, outlet nozzle of warm air dryers in fifteen air dryers used in these washrooms. Bacteria were found to be relatively numerous in the air flows. Bacterially contaminated air was found to be emitted whenever a warm air dryer was running, even when not being used for hand drying. Our investigation shows that Staphylococcus haemolyticus, Micrococcus luteus, Pseudomonas alcaligenes, Bacillus cereus and Brevundimonad diminuta/vesicularis were emitted from all of the dryers sampled, with 95% showing evidence of the presence of the potential pathogen S. haemolyticus. It is concluded that hot air dryers can deposit pathogenic bacteria onto the hands and body of users. Bacteria are distributed into the general environment whenever dryers are running and could be inhaled by users and none-users alike. The results provide an evidence base for the development and enhancement of hygienic hand drying practices.

Sustainability assessment of heat exchanger units for spray dryers

International Nuclear Information System (INIS)

Caglayan, Hasan; Caliskan, Hakan

2017-01-01

In this study, the sustainability assessment is performed to the system known as heat exchanger unit with spray dryer. The five-different dead state temperatures (0-5-10-15-20 °C) are considered. It is found that the heat exchanger has the highest energy efficiency (63.32%), while the overall system has the lowest one (5.56%). So, the combination of the spray dryer with the heat exchanger is more effective. On the other hand, the overall exergy efficiency of the system is lower than the heat exchanger and spray dryer for all of the dead state (environmental) temperatures. The exergy efficiency of the heat exchanger is inversely proportional to the dead state temperature, and the maximum rate is found as 49.65% at 0 °C. Furthermore, the exergy efficiencies of the spray dryer and overall system are directly proportional to the dead state temperatures, and the corresponding maximum rates are found to be 26.41% and 24.32% at 20 °C, respectively. Also, the exergy destruction is directly proportional to the dead state temperatures. The minimum and maximum exergy destruction rates are found at the dead state temperatures of 0 °C and 20 °C, respectively. Furthermore, the most sustainable system is found as the heat exchanger unit. - Highlights: • Thermodynamic analyses of industrial heat exchangers and spray dryers. • Sustainability of heat exchangers for spray dryers. • Dead state temperature effects on exergy efficiencies of heat exchangers and spray dryers.

Coke degradation by surface breakage in a modified tumble drum

Energy Technology Data Exchange (ETDEWEB)

Litster, J D

1987-01-01

The surface breakage rate constant for three Australian battery cokes was measured in a specially modified tumble drum using a previously developed technique. The effect of experimental test parameters - coke size, sample mass, drum speed, lifter height and lifter number - on the surface breakage rate constant was examined. The motion of coke particles within a tumble drum was filmed in a simulation experiment with a 0.31 m diameter drum. Particles were raised on the lifters, fell and collided with the bottom of the drum. These collisions were the main source of fines (minus 1 mm) production rather than true abrasion as depicted by a rubbing, rolling action. Hence the term 'surface breakage' is more appropriate than 'abrasion' to describe the breakage process. By measuring the volume of coke carried by each lifter and the height of fall of the coke, the effect of drum speed, sample mass, lifter height and number on the rate of surface breakage was successfully explained. The surface breakage rate constant was found to be proportional to particle size to the power 0.33 for the three cokes studied. A normalized surface breakage rate constant was derived which allowed comparison of cokes with different size distributions. This parameter characterises the coke surface breakage resistance.

Design, manufacture and modeling of a mixed mode dryer for pistachio in Kerman

Energy Technology Data Exchange (ETDEWEB)

Ameri, Mehran; Zangiabadi, Bijan; Mahmoudabadi, Mehdi [Department of Mechanical Engineering, Shahid Bahonar University, Kerman (Iran, Islamic Republic of)

2006-01-15

Production of high quality nuts that have toxics less than 2-2.5 ppm requires a great attention during growing and post harvest processing. Gravitational or Wagon driver using fossil fuel has been traditionally performed to dry pistachio nuts. However, using of fossil fuel is subject to the noxious effects on nuts such as burning, discoloured and various toxic fumes as well as the biological pollution. In Kerman province in south of Iran, where 60% of pistachio nuts export to all over the world, due to long period of sunshine during harvesting season, solar drying are know to be an excellence alternative to the fossil fuel. A specimen mixed-mode solar-dryer is manufactured to study the feasibility of test and to investigate optimization of the drying process in several conditions. Furthermore this designed dryer for pistachio nuts can be simply used for drying of the various agriculture products like fruits and vegetables. With this proposed multi application solar dryer, one can easily reach to acceptable moisture (7%) in a short period of time. For this system a mathematical model of dryer is also suggested here. the proposed solar dryer includes three main parts as collector, chamber and photocell. Chamber has a glassy cover that permits nut expose beam radiation directly. Collector has ability to circulate air by buoyancy forces or convey air by suction fans due to different operation conditions. Photocells prepare electromotive force for fans.National capacity of the dryer is 50Kg. The maximum temperature inside collector at the end of harvest season is 60 degree centigrade during 8-16 local time. In the mathematical modeling after fitting the drawing curves with the remaining moisture amount in the nuts and temperature per drying time, it was found that the major drop in the moisture content of the nuts occurs during the first 9 hours and then decreases gradually. The final moisture amount of the nuts was about 6% in 42 hours. The accuracy of proposed method

Design, manufacture and modeling of a mixed mode dryer for pistachio in Kerman

International Nuclear Information System (INIS)

Ameri, Mehran; Zangiabadi, Bijan; Mahmoudabadi, Mehdi

2006-01-01

Production of high quality nuts that have toxics less than 2-2.5 ppm requires a great attention during growing and post harvest processing. Gravitational or Wagon driver using fossil fuel has been traditionally performed to dry pistachio nuts. However, using of fossil fuel is subject to the noxious effects on nuts such as burning, discoloured and various toxic fumes as well as the biological pollution. In Kerman province in south of Iran, where 60% of pistachio nuts export to all over the world, due to long period of sunshine during harvesting season, solar drying are know to be an excellence alternative to the fossil fuel. A specimen mixed-mode solar-dryer is manufactured to study the feasibility of test and to investigate optimization of the drying process in several conditions. Furthermore this designed dryer for pistachio nuts can be simply used for drying of the various agriculture products like fruits and vegetables. With this proposed multi application solar dryer, one can easily reach to acceptable moisture (7%) in a short period of time. For this system a mathematical model of dryer is also suggested here. the proposed solar dryer includes three main parts as collector, chamber and photocell. Chamber has a glassy cover that permits nut expose beam radiation directly. Collector has ability to circulate air by buoyancy forces or convey air by suction fans due to different operation conditions. Photocells prepare electromotive force for fans.National capacity of the dryer is 50Kg. The maximum temperature inside collector at the end of harvest season is 60 degree centigrade during 8-16 local time. In the mathematical modeling after fitting the drawing curves with the remaining moisture amount in the nuts and temperature per drying time, it was found that the major drop in the moisture content of the nuts occurs during the first 9 hours and then decreases gradually. The final moisture amount of the nuts was about 6% in 42 hours. The accuracy of proposed method

solar dryer with biomass backup heater for drying fruits

African Journals Online (AJOL)

SOLAR DRYER WITH BIOMASS BACKUP HEATER FOR DRYING FRUITS: DEVELOPMENT AND PERFORMANCE ANALYSIS. ... Journal of Science and Technology (Ghana) ... Most solar dryers rely on only solar energy as the heat source.

Corn Drying with Zeolite in The Fluidized Bed Dryer under Medium Temperature

Directory of Open Access Journals (Sweden)

Mohamad Djaeni

2013-08-01

Full Text Available Drying is an important step to find high quality of corn. Based on Standard of National Industry, populer as SNI, number 01-3920-1995, the corn was well stored at moisture content 14% or below (wet basis. However, conventional corn drying dealed with in-efficient energy process and corn quality degradation. This research evaluated the performance of corn drying assisted by zeolite as moisture adsorbent. In this process, the zeolite and corn were placed in the dryer fluidized by warm air as drying medium under 40 - 50oC. The air evaporated water product from corn, and at same time the zeolite adsorbed moisture in air. So, the relative humidity of air in dryer can be kept low in which enhanced the driving force for drying. Beside that, the moisture adsoprtion by zeolite was exothermic process that can supply the energy for drying or keep the dryer temperature. Thus, the drying rate can be faster. This work foccussed to observe the effect of drying temperature, air velocity, and corn to zeolite ratio on drying time as well as corn quality. As indicators, the drying rate was estimated and the proxymates content such as protein, fat, and carbohydrate content were analyzed. The results showed that compared with conventional fluidised bed dryer, corn drying with zeolite, can speed up drying time as well as improving the constant of drying rate. In addition, the corn proximate nutrition content can be well retained. At operating temperature 40oC, air velocity 9 m.s-1, and zeolite to corn ratio 1:2, the drying time can be 60 minutes shorter compared to that without zeolite.

Assessment of the bacterial contamination of hand air dryer in washrooms

OpenAIRE

Alharbi, Sulaiman Ali; Salmen, Saleh Hussein; Chinnathambi, Arunachalam; Alharbi, Naiyf S.; Zayed, M.E.; Al-Johny, Bassam O.; Wainwright, Milton

2016-01-01

The present study was carried out, using standard techniques, to identify and count the bacterial contamination of hand air dryers, used in washrooms. Bacteria were isolated from the air flow, outlet nozzle of warm air dryers in fifteen air dryers used in these washrooms. Bacteria were found to be relatively numerous in the air flows. Bacterially contaminated air was found to be emitted whenever a warm air dryer was running, even when not being used for hand drying. Our investigation shows th...

Technical and environmental analysis of biofuel dryers; Teknisk och miljoemaessig analys av biobraensletorkar

Energy Technology Data Exchange (ETDEWEB)

Muenter, M; Hagman, U; Harnevie, H; Johansen, H; Kristensson, I; Westermark, M; Viberg, T [Vattenfall Energimarknad, Stockholm (Sweden)

1999-03-01

A study regarding technology and environmental impact of the drying process of biofuels has been conducted. In the study two different types of dryers are analyzed. The result from the study shows that emissions of primarily hydrocarbons is high from the direct technic. The emission can be decreased considerably by improving the burner of the dryer. For the indirect technic the evaporated water give rise to problems in the sewage treatment plant. Studies show that biological treatment will result in an acceptable condensate.

Handling 78,000 drums of mixed-waste sludge

International Nuclear Information System (INIS)

Berry, J.B.; Gilliam, T.M.; Harrington, E.S.; Youngblood, E.L.; Baer, M.B.

1991-01-01

The Oak Ridge Gaseous Diffusion Plant (now know as the Oak Ridge K-25 Site) prepared two mixed-waste surface impoundments for closure by removing the sludge and contaminated pond-bottom clay and attempting to process it into durable, nonleachable, concrete monoliths. Interim, controlled, above-ground storage of the stabilized waste was planned until final disposition. The strategy for disposal included delisting the stabilized pond sludge from hazardous to nonhazardous and disposing of the delisted monoliths as radioactive waste. Because of schedule constraints and process design and control deficiencies, ∼46,000 drums of material in various stages of solidification and ∼32,000 drums of unprocessed sludge are presently being stored. In addition, the abandoned treatment facility still contains ∼16,000 gal of raw sludge. Such conditions do not comply with the requirements set forth by the Resource Conservation and Recovery Act (RCRA) for the storage of listed waste. Various steps are being taken to bring the storage of ∼78,000 drums of mixed waste into compliance with RCRA. This paper (1) reviews the current situation, (2) discusses the plan for remediation of regulatory noncompliances, including decanting liquid from stabilized waste and dewatering untreated waste, and (3) provides an assessment of alternative raw-waste treatment processes. 1 ref., 6 figs., 2 tabs

Biogas utilization for drying sweet potato chips by using infrared dryer

Science.gov (United States)

Sriharti, Rahayuningtyas, Ari; Susanti, Novita Dwi; Sitompul, Rislima Febriani

2017-11-01

This study aims to utilize biogas, that produced from organic waste, as fuel for infrared dryers. The digester was dome type, which made from fiberglass, 5.5 m3 capacities, gas container made from soft PVC, 5.6 m3 capacities. The infrared dryer was household scale which have dimension 2000 mm x 2000 mm x 2000 mm, it is consist of 2 racks, which have size 1500 mm x 500 mm x 1400 mm, and consist of 44 baking pans (600 mm X 400 mm x 30 mm), the dryer has 36 kg of capacity. The parameters observed include ambient temperature, temperature inside the digester, pH value, biogas production, drying room temperature, moisture content of sweet potato and biogas consumption for drying. Infrared dryer is used to dry the sweet potato slices thickness of 2 mm with total amount 12 kg, at room temperature dryer ± 60 °C. The results showed that the average biogas production was 1.335 m3 per day, at a temperature of 26 - 35 °C and the neutral pH value was 6.99 - 7.7. 12 kg of sweet potato sliced dried for 4 hours, the initial moisture content of 79.68 % decreased to 8.98 %, the consumption of biogas used 4,952 m3. The final result of drying process of sweet potato slices of 3.5 kg, there was a shrinkage of 70.83 %. Characterization of sweet potato slices is 3 % protein, 0,6 % fat, 94 % carbohydrate and 2 % ash. These sweet potato can be used as flour for cookies and cake raw materials, the use of sweet potato flour can reach 50 - 100 %.

Performance Analysis of a Solar Dryer Equipped with a Recycling Air System and Desiccant Chamber

Directory of Open Access Journals (Sweden)

M.H Aghkhani

2013-09-01

Full Text Available Drying is a high energy consuming process. Solar drying is one of the most popular methods for dehydration of agricultural products. In the present study, the performance of a forced convection solar dryer equipped with recycling air system and desiccant chamber was investigated. The solar dryer is comprised of solar collector, drying chamber, silica jell desiccant chamber, air ducts, fan and measuring and controlling system. Drying rate and energy consumption in three levels of air temperature (40, 45 and 50 oC and two modes of drying (with recycling air and no-recycling with open duct system were measured and compared. The results showed that increasing the drying air temperature decreased the drying time and increased the energy consumption in the mode of non-recycling air system. The dryer efficiency and drying rate were better in the mode of recycling air system than open duct system. The highest dryer efficiency was obtained from drying air temperature of 50 oC and the mode of recycling air system. In general, the efficiency of solar collector and the highest efficiency of the dryer were 0.34 and 0.41, respectively.

Farm level evaluation of biomass energy operated seed dryer at selected sites of Bangladesh

International Nuclear Information System (INIS)

Rahman, S.M.M.; Bhuiyan, M.G.K.; Rahman, M.A.; Baqui, M.A.; Bala, B.K.

2006-01-01

Drying is one of the major problem in post harvest and processing of farm produce specially paddy seed in Bangladesh resulting tremendous shortage of quality seed. Evaluation through demonstrations was undertaken for the resource poor farmers at the selected sites to have practical experience of the IRRI-BRRI seed dryer. Viability of the dried paddy was more than 90% after six months of storage. The farmers were satisfied on the performance of the dryer. 68-100% farmers were motivated to hire the dyer during Boro and Aus seasons. Thus, the farm level evaluation and adoption of seed dryer will give a better alternative, aware and motivate the farmers on producing quality seed through proper drying and will contribute increased production

Modeling VOC transport in simulated waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

1993-06-01

A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the VOC permeability had been measured. Permeabilities for five VOCs [methylene chloride, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), 1,1,1-trichloroethane, carbon tetrachloride, and trichloroethylene] were measured across a polyethylene bag. Comparison of model and experimental results of VOC concentration as a function of time indicate that model accurately accounts for significant VOC transport mechanisms in a lab-scale waste drum

Economic Optimization of Spray Dryer Operation using Nonlinear Model Predictive Control

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2014-01-01

In this paper we investigate an economically optimizing Nonlinear Model Predictive Control (E-NMPC) for a spray drying process. By simulation we evaluate the economic potential of this E-NMPC compared to a conventional PID based control strategy. Spray drying is the preferred process to reduce...... the water content for many liquid foodstuffs and produces a free flowing powder. The main challenge in controlling the spray drying process is to meet the residual moisture specifications and avoid that the powder sticks to the chamber walls of the spray dryer. We present a model for a spray dryer that has...... been validated on experimental data from a pilot plant. We use this model for simulation as well as for prediction in the E-NMPC. The E-NMPC is designed with hard input constraints and soft output constraints. The open-loop optimal control problem in the E-NMPC is solved using the single...

Development and Evaluation of Solar Tunnel Dryer for Commercial Fish Drying

Science.gov (United States)

Mohod, A. G.; Khandetod, Y. P.; Shrirame, H. Y.

2014-01-01

The local practice of drying fish in open sun drying poses problems such as high moisture content, uncontrolled drying and contamination. These problems can be avoided by proper use of improved methods such as the solar tunnel dryer, which results in faster drying of fish. The semi cylindrical walk-in type natural convection solar tunnel dryer, having drying area of 37.5 m2 was developed and evaluated for the drying of fish products in comparison with the conventional method of open sun drying. The experiments were conducted without fish and with fish to evaluate the performance of solar tunnel dryer. The average rise in temperature inside the solar tunnel dryer was found to be 11.24 °C and 18.29 °C over the ambient temperature during no load test in winter and summer respectively. The average 28 % saving in time was observed for selected fish drying using solar tunnel dryer over open sun drying method with average drying efficiency of 19 %. The economics was calculated for drying of prawns ( Parapaeneopsis stylifera) by solar tunnel dryer and open sun drying system on the basis of business as a whole. The economics of the solar tunnel dryer is presented in term of Net present worth, Benefit-Cost Ratio, Payback period, Profitability index and Internal rate of return. The pay back period for solar tunnel dryer was found to be 2.84 years.

49 CFR 178.505 - Standards for aluminum drums.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Standards for aluminum drums. 178.505 Section 178... PACKAGINGS Non-bulk Performance-Oriented Packaging Standards § 178.505 Standards for aluminum drums. (a) The following are the identification codes for aluminum drums: (1) 1B1 for a non-removable head aluminum drum...

Development of SGS for various waste drums

International Nuclear Information System (INIS)

Kim, Ki-Hong; Ryu, Young-Gerl; Kwak, Kyung-Kil; Ji, Yong-Young

2006-01-01

Radioactive waste assay system was manufactured to measure the individual nuclides' activity in homogeneous and non-homogeneous waste drums and to exclude worker's exposure. After measuring the activities of all individual γ-emitters, our system was programmed to calculate the activities of α, Β emitters, automatically and then calculated total activities of drum by utilizing scaling factor (relationship between α, Β emitters and Co-60, Cs-137). In general, SGS (Segmented gamma Scanning system) divided a waste drum into 8 segments vertically, and also 8 sectors in one segment to minimize the error. And SGS can be determined the density of drum by using the several matrix correction methods such as transmission ratio, differential peak absorption and mean density correction, individually or by combination. However, from the NPPs and other nuclear facilities, various drum (100∼350L) could be generated. To analyze the activities of γ-emitters from various drums, we modified the collimator (horizontal and vertical) and added detector mover to the existing SGS system. As a results, the measurement error was <12% in a short distance (10 segments, Co-60; 47.87μCi and Cs-137; 101.16μCi) and was <25% in a long distance (8 segments, same sources). This system can be applied to the drum which TGS system does not analyze drum (for example, high density, high activities and large volume). (author)

Sound analysis of a cup drum

International Nuclear Information System (INIS)

Kim, Kun ho

2012-01-01

The International Young Physicists’ Tournament (IYPT) is a worldwide tournament that evaluates a high-school student's ability to solve various physics conundrums that have not been fully resolved in the past. The research presented here is my solution to the cup drum problem. The physics behind a cup drum has never been explored or modelled. A cup drum is a musical instrument that can generate different frequencies and amplitudes depending on the location of a cup held upside-down over, on or under a water surface. The tapping sound of a cup drum can be divided into two components: standing waves and plate vibration. By individually researching the nature of these two sounds, I arrived at conclusions that could accurately predict the frequencies in most cases. When the drum is very close to the surface, qualitative explanations are given. In addition, I examined the trend of the tapping sound amplitude at various distances and qualitatively explained the experimental results. (paper)

Drum inspection robots: Application development

International Nuclear Information System (INIS)

Hazen, F.B.; Warner, R.D.

1996-01-01

Throughout the Department of Energy (DOE), drums containing mixed and low level stored waste are inspected, as mandated by the Resource Conservation and Recovery Act (RCRA) and other regulations. The inspections are intended to prevent leaks by finding corrosion long before the drums are breached. The DOE Office of Science and Technology (OST) has sponsored efforts towards the development of robotic drum inspectors. This emerging application for mobile and remote sensing has broad applicability for DOE and commercial waste storage areas. Three full scale robot prototypes have been under development, and another project has prototyped a novel technique to analyze robotically collected drum images. In general, the robots consist of a mobile, self-navigating base vehicle, outfitted with sensor packages so that rust and other corrosion cues can be automatically identified. They promise the potential to lower radiation dose and operator effort required, while improving diligence, consistency, and documentation

Neural network modeling of drying of rice in BAU-STR dryer

Science.gov (United States)

Alam, Md. Ashraful; Saha, Chayan Kumer; Alam, Md. Monjurul; Ashraf, Md. Ali; Bala, Bilash Kanti; Harvey, Jagger

2018-05-01

The experimental performance and artificial neural network modeling of rice drying in BAU-STR dryer is presented in this paper. The dryer consists of a biomass stove as a heat source, a perforated inner bin and a perforated outer bin with annular space for grains, and a blower (1 hp) to supply heated air. The dryer capacity was 500 kg of freshly harvested rice. Twenty experimental runs were conducted to investigate the experimental performance of the dryer for drying of rice. An independent multilayer neural network approach was used to predict the performance of the BAU-STR dryer for drying of rice. Ten sets of experimental data were used for training using back propagation algorithm and another ten sets of data were used for testing the artificial neural network model. The prediction of the performance of the dryer was found to be excellent after it was adequately trained. The statistical analysis showed that the errors (MSE and RMSE) were within and acceptable range of ±5% with a coefficient of determination (R2) of 99%. The model can be used to predict the potential of the dryer for different locations, and can also be used in a predictive optimal control algorithm.

Mechanical Modeling of a WIPP Drum Under Pressure

Energy Technology Data Exchange (ETDEWEB)

Smith, Jeffrey A. [Sandia National Laboratories, Albuquerque, NM (United States)

2014-11-25

Mechanical modeling was undertaken to support the Waste Isolation Pilot Plant (WIPP) technical assessment team (TAT) investigating the February 14th 2014 event where there was a radiological release at the WIPP. The initial goal of the modeling was to examine if a mechanical model could inform the team about the event. The intention was to have a model that could test scenarios with respect to the rate of pressurization. It was expected that the deformation and failure (inability of the drum to contain any pressure) would vary according to the pressurization rate. As the work progressed there was also interest in using the mechanical analysis of the drum to investigate what would happen if a drum pressurized when it was located under a standard waste package. Specifically, would the deformation be detectable from camera views within the room. A finite element model of a WIPP 55-gallon drum was developed that used all hex elements. Analyses were conducted using the explicit transient dynamics module of Sierra/SM to explore potential pressurization scenarios of the drum. Theses analysis show similar deformation patterns to documented pressurization tests of drums in the literature. The calculated failure pressures from previous tests documented in the literature vary from as little as 16 psi to 320 psi. In addition, previous testing documented in the literature shows drums bulging but not failing at pressures ranging from 69 to 138 psi. The analyses performed for this study found the drums failing at pressures ranging from 35 psi to 75 psi. When the drums are pressurized quickly (in 0.01 seconds) there is significant deformation to the lid. At lower pressurization rates the deformation of the lid is considerably less, yet the lids will still open from the pressure. The analyses demonstrate the influence of pressurization rate on deformation and opening pressure of the drums. Analyses conducted with a substantial mass on top of the closed drum demonstrate that the

Evaluation of hybrid solar – biomass dryer with no load

Directory of Open Access Journals (Sweden)

Yassen Tadahmun Ahmed

2014-07-01

Full Text Available Experimental study was carried out to investigate the performance of designed and fabricated hybrid solar-biomass dryer without load. The solar side was a natural convection mixed mode, while the biomass side was a hot air produced from a burner/gas to gas heat exchanger. The experiments have been conducted to test the dryer temperature, inlet and outlet relative humidity, outlet velocity, and biomass feeding rate. In the solar mode the maximum dryer temperature was 63°C. Behaviours of the velocity in the dryer was found to follow solar radiation available to the dryer. The velocity was in the range of 0.6 – 1.35 m/s through the 0.0176 m2 area of the outlet when the solar radiation was in the range of 150 – 880 W/m2. Two feeding rates of wood were used to investigate the dryer performance through the night. The results showed that at feeding rate 278 g/hr, the drying air mean temperature was 62 ºC. This temperature was more suitable than the measured drying air temperature at feeding rate 490 g/hr. Also the 62 °C drying environment is more stable and feasible for drying almost all types of products.

Effectiveness of a heat exchanger in a heat pump clothes dryer

Science.gov (United States)

Nasution, A. H.; Sembiring, P. G.; Ambarita, H.

2018-02-01

This paper deals with study on a heat pump clothes dryer coupled with a heat exchanger. The objective is to explore the effects of the heat exchanger on the performance of the heat pump dryer. The heat pump dryer consists of a vapor compression cycle and integrated with a drying room with volume 1 m3. The power of compressor is 800 Watt and the refrigerant of the cycle is R22. The heat exchanger is a flat plate type with dimensions of 400 mm × 400 mm × 400 mm. The results show the present of the heat exchanger increase the performance of the heat pump dryer. In the present experiment the COP, TP and SMER increase 15.11%, 4.81% and 58.62%, respectively. This is because the heat exchanger provides a better drying condition in the drying room with higher temperature and lower relative humidity in comparison with heat pump dryer without heat exchanger. The effectiveness of the heat exchanger is also high, it is above 50%. It is suggested to install a heat exchanger in a heat pump dryer.

Cookoff Modeling of a WIPP waste drum (68660)

Energy Technology Data Exchange (ETDEWEB)

Hobbs, Michael L. [Sandia National Laboratories, Albuquerque, NM (United States)

2014-11-24

A waste drum located 2150 feet underground may have been the root cause of a radiation leak on February 14, 2014. Information provided to the WIPP Technical Assessment Team (TAT) was used to describe the approximate content of the drum, which included an organic cat litter (Swheat Scoop®, or Swheat) composed of 100% wheat products. The drum also contained various nitrate salts, oxalic acid, and a nitric acid solution that was neutralized with triethanolamine (TEA). CTH-TIGER was used with the approximate drum contents to specify the products for an exothermic reaction for the drum. If an inorganic adsorbent such as zeolite had been used in lieu of the kitty litter, the overall reaction would have been endothermic. Dilution with a zeolite adsorbent might be a useful method to remediate drums containing organic kitty litter. SIERRA THERMAL was used to calculate the pressurization and ignition of the drum. A baseline simulation of drum 68660 was performed by assuming a background heat source of 0.5-10 W of unknown origin. The 0.5 W source could be representative of heat generated by radioactive decay. The drum ignited after about 70 days. Gas generation at ignition was predicted to be 300-500 psig with a sealed drum (no vent). At ignition, the wall temperature increases modestly by about 1°C, demonstrating that heating would not be apparent prior to ignition. The ignition location was predicted to be about 0.43 meters above the bottom center portion of the drum. At ignition only 3-5 kg (out of 71.6 kg total) has been converted into gas, indicating that most of the material remained available for post-ignition reaction.

Use of drum driers for processing various industrial wastes into high-grade animal feeding stuffs

Energy Technology Data Exchange (ETDEWEB)

Fritze, H

1976-01-01

Strict anti-pollution legislation governing admissible effluent concentrations and high charges are forcing certain industries (potato starch and dried potato flake factories, sugar factories and dairies) to install facilities for recovering valuable substances, which are used mainly as fodder. In this way the effluent charges can be reduced and a return is obtained on the investment and operating costs. Processes are described whereby such substances can be extracted efficiently when using Escher Wyss drum driers.

The impact of immersion protection requirements on hair dryer electrocutions in the USA.

Science.gov (United States)

Rodgers, Gregory B; Garland, Sarah

2012-12-01

To evaluate the effectiveness of the immersion protection requirements of a voluntary safety standard for portable handheld hair dryers in preventing electrocution deaths in the USA. The present work was an interrupted time series study design. Data on annual hair dryer-related electrocution deaths resulting from water contact were developed for the 1980-2007 study period. A multivariate Poisson regression model for rate data was used to evaluate the impact of the immersion protection requirements during the post-intervention period. The analysis controlled for the estimated number of hair dryers in use and the estimated number of US homes equipped with ground fault circuit interrupters, safety devices that would address hair dryer electrocutions even in the absence of the immersion protection requirements of the voluntary standard. The implementation of the 1987 and 1991 immersion protection requirements of the voluntary standard for portable handheld hair dryers was the intervention studied. The main outcome measure was the estimated reduction in the hair dryer electrocution rate associated with the immersion protection requirements of the voluntary standard. After controlling for covariates, the immersion protection requirements were estimated to reduce the rate of hair dryer immersion electrocution deaths by 96.6% (95% CI, 90.8% to 98.8%). This suggests the prevention of about 280 immersion electrocution deaths involving hair dryers during the post-intervention period (1987-2007). The immersion protection requirements of the voluntary safety standard for hair dryers have been highly effective in reducing hair dryer electrocutions.

Sealing of rotary drums for operation under pressurized conditions

International Nuclear Information System (INIS)

Shirvani, M.; Khanof, M. H.; Yousefi, M. R.; Sadighi, S.

2006-01-01

In practice, rotary drums are always designed for operation under vacuum conditions. In this paper, a novel technique is proposed for sealing the rotary drums under pressurized conditions. The proposed system is based on applying a secondary pressurized volume around the leaking gap of the drum. By controlling the pressure of this volume above the pressure of the drum, it will be possible to prevent from any leakage of gases to the ambient. The objective of a controller in this system is that the pressure of secondary volume be kept above the pressure of the drum in spite of the disturbances which may be exerted on the system by the wind outside the drum. The control system is also required to trace the variations in the drum pressure with the least fluctuations in the pressure difference among the drum and the volume

Gas formation in drum waste packages of Paks NPP

International Nuclear Information System (INIS)

Molnar, M.; Palcsu, L.; Svingor, E.; Szanto, Z.; Futo, I.; Ormai, P.

2000-01-01

Gas composition measurements have been carried out by mass spectrometry analysis of samples taken from the headspace of ten drum waste packages generated and temporarily stored at Paks NPP. Four drums contained compacted solid waste, three drums were filled with grouted (solidified) sludge and three drums contained solid waste without compaction. The drums have been equipped with a special gas outlet system to make repeated sampling possible. Based on the first measurements significant differences in the gas composition and the rate of gas generation among the drums were found. (author)

Packaging design criteria for the Type B Drum

International Nuclear Information System (INIS)

Edwards, W.S.; Smith, R.J.; Wells, A.H.

1995-09-01

The Type B Drum package is a transportation cask capable of shipping a single 55-gal (208 L) drum of transuranic (TRU) waste. The Type B Drum is smaller than existing certified packages, such as the TRUPACT-II cask, but will allow payloads with higher thermal and gas generation rates, thus providing greater operational flexibility. The Type B Drum package has double containment so that plutonium contents and other radioactive material may be transported in Type B quantities. Conceptual designs of unshielded and shielded versions of the Type B Drum were completed in Report on the Conceptual Design of the Unshielded Type B Drum Packaging and Report on the Conceptual Design of the Shielded type B Drum Packaging (WEC 1994a, WEC 1994b), which demonstrated the Type B Drum to be a viable packaging system. A Type B package containment system must withstand the normal conditions of transport and the hypothetical accident conditions, which include a 9-m (30-ft) drop onto an unyielding surface and a 1-m (3-ft) drop onto a 15-cm (6-in.) diameter pin, and a fire and immersion scenarios

Buoy-Rope-Drum Wave Power System

Directory of Open Access Journals (Sweden)

Linsen Zhu

2013-01-01

Full Text Available A buoy-rope-drum wave power system is a new type of floating oscillating buoy wave power device, which absorbs energy from waves by buoy-rope-drum device. Based on the linear deep water wave theory and pure resistive load, with cylinder buoy as an example, the research sets up the theoretical model of direct-drive buoy-rope-drum wave power efficiency and analyzes the influence of the mass and load of the system on its generating efficiency. It points out the two main categories of the efficient buoy-rope-drum wave power system: light thin type and resonance type, and optimal designs of their major parameters are carried out on the basis of the above theoretical model of generating efficiency.

Active Drumming Experience Increases Infants' Sensitivity to Audiovisual Synchrony during Observed Drumming Actions.

Science.gov (United States)

Gerson, Sarah A; Schiavio, Andrea; Timmers, Renee; Hunnius, Sabine

2015-01-01

In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition.

DEGRADATION EVALUATION OF HEAVY WATER DRUMS AND TANKS

Energy Technology Data Exchange (ETDEWEB)

Mickalonis, J.; Vormelker, P.

2009-07-31

Heavy water with varying chemistries is currently being stored in over 6700 drums in L- and K-areas and in seven tanks in L-, K-, and C-areas. A detailed evaluation of the potential degradation of the drums and tanks, specific to their design and service conditions, has been performed to support the demonstration of their integrity throughout the desired storage period. The 55-gallon drums are of several designs with Type 304 stainless steel as the material of construction. The tanks have capacities ranging from 8000 to 45600 gallons and are made of Type 304 stainless steel. The drums and tanks were designed and fabricated to national regulations, codes and standards per procurement specifications for the Savannah River Site. The drums have had approximately 25 leakage failures over their 50+ years of use with the last drum failure occurring in 2003. The tanks have experienced no leaks to date. The failures in the drums have occurred principally near the bottom weld, which attaches the bottom to the drum sidewall. Failures have occurred by pitting, crevice and stress corrosion cracking and are attributable, in part, to the presence of chloride ions in the heavy water. Probable degradation mechanisms for the continued storage of heavy water were evaluated that could lead to future failures in the drum or tanks. This evaluation will be used to support establishment of an inspection plan which will include susceptible locations, methods, and frequencies for the drums and tanks to avoid future leakage failures.

Storage drums for radio-active waste

International Nuclear Information System (INIS)

Knights, H.C.

1982-01-01

The lid of a storage drum for radioactive waste is secured by a series of clamps each of which has a hook for engaging the rim of the drum. Each clamp has an indicating means whereby a remote operator can check that the lid is secured to the drum. In a second embodiment, the position of an arm acts as a visual indication as to whether or not the clamp is in engagement with the container rim. (author)

New practical method for evaluation of a conventional flat plate continuous pistachio dryer

Energy Technology Data Exchange (ETDEWEB)

Kouchakzadeh, Ahmad [Agri Machinery Engineering, Ilam University, Ilam (Iran, Islamic Republic of); Tavakoli, Teymur [Agri Machinery Engineering, Tarbyat Modares University, Tehran (Iran, Islamic Republic of)

2011-07-15

Highlights: {yields} Evaluation of a conventional flat plate continuous pistachio dryer with a new feasible method. {yields} Using thermophysical properties of air and matter. {yields} This manner could be utilized in similar dryer for other agricultural products. {yields} Method shows the heat loss and power separately. -- Abstract: Testing a dryer is necessary to evaluate its absolute and comparative performance with other dryers. A conventional flat plate continuous pistachio dryer was tested by a new practical method of mass and energy equilibrium. Results showed that the average power consumption and heat loss in three tests are 62.13 and 18.99 kW, respectively. The ratio of heat loss on power consumption showed that the efficiency of practical pistachios flat plate dryer is about 69.4%.

New practical method for evaluation of a conventional flat plate continuous pistachio dryer

International Nuclear Information System (INIS)

Kouchakzadeh, Ahmad; Tavakoli, Teymur

2011-01-01

Highlights: → Evaluation of a conventional flat plate continuous pistachio dryer with a new feasible method. → Using thermophysical properties of air and matter. → This manner could be utilized in similar dryer for other agricultural products. → Method shows the heat loss and power separately. -- Abstract: Testing a dryer is necessary to evaluate its absolute and comparative performance with other dryers. A conventional flat plate continuous pistachio dryer was tested by a new practical method of mass and energy equilibrium. Results showed that the average power consumption and heat loss in three tests are 62.13 and 18.99 kW, respectively. The ratio of heat loss on power consumption showed that the efficiency of practical pistachios flat plate dryer is about 69.4%.

Shearer drums - the cutting edge

Energy Technology Data Exchange (ETDEWEB)

O' Neill, M.; Wright, C.

2004-09-15

The paper discusses continuous miner and shearer cutters. It claims cutting drum require the same level of engineering know-how and technical expertise as do the machines driving them, and that the cutting drum, whether on a longwall shearer or continuous miner, comprises, the steel, pedestals, bit holders and the bits.

Improving adsorption dryer energy efficiency by simultaneous optimization and heat integration

NARCIS (Netherlands)

Atuonwu, J.C.; Straten, G. van; Deventer, H.C. van; Boxtel, A.J.B. van

2011-01-01

Conventionally, energy-saving techniques in drying technology are sequential in nature. First, the dryer is optimized without heat recovery and then, based on the obtained process conditions, heat recovery possibilities are explored. This work presents a methodology for energy-efficient adsorption

Metabolic Demands of Heavy Metal Drumming

Directory of Open Access Journals (Sweden)

Bryan Romero

2016-07-01

Full Text Available Background: The drum set involves dynamic movement of all four limbs. Motor control studies have been done on drum set playing, yet not much is known about the physiological responses to this activity. Even less is known about heavy metal drumming. Aims: The purpose of this study was to determine metabolic responses and demands of heavy metal drumming. Methods: Five semi-professional male drummers (mean ± SD age = 27.4 ± 2.6 y, height = 177.2 ± 3.8 cm, body mass = 85.1 ± 17.8 kg performed four prescribed and four self-selected heavy metal songs. Oxygen consumption (VO2, minute ventilation (VE and respiratory exchange ratio (RER were measured using a metabolic cart.  Heart rate (HR was measured using a heart rate monitor. VO2max was determined using a graded cycle ergometer test. Results: The results indicated a metabolic cost of 6.3 ± 1.4 METs and heart rate of 145.1 ± 15.7 beats·min-1 (75.4 ± 8.3% of age-predicted HRmax. VO2 peak values reached approximately 90% of the drummer’s VO2max when performing at the fastest speeds. According to these results, heavy metal drumming may be considered vigorous intensity activity (≥ 6.0 METs. The relative VO2max of 40.2 ± 9.5 mL·kg·min-1 leads to an aerobic fitness classification of “average” for adult males. Conclusions: The metabolic demands required during heavy metal drumming meet the American College of Sports Medicine guidelines for the development of health related fitness.  Keywords: Drum set, Exercise physiology, VO2, Music

Development and performance evaluation of forced convection potato solar dryer

International Nuclear Information System (INIS)

Khan, M.A.; Sabir, M.S.; Iqbal, M.

2011-01-01

This research paper deals with the design development and testing of a forced convection solar dryer, for drying and converting to flour of high moisture content vegetables like potatoes. The angle of solar collector was made adjustable for the absorption of maximum solar radiation by the absorber plate. The air flow rate was controlled by adjustable gate valve to find the optimum flow rate for dehydration of the product. The penetration of solar radiation raised the temperature of the absorber plate of the dryer to 110 deg. C during the operation under stagnation or no load conditions. The maximum air temperature attained in the solar air heater, under this condition was 80 deg. C. The dryer was loaded with 12 Kg of blanched potato chips having an initial moisture content of 89.75%, and the final desired moisture content of 6.95% was achieved within five hours without losing the color of potato chips, while the moisture contents reduction was from 89.75% to 33.75% for five hours in open sun drying under shade. The drying cost for 1 Kg of potatoes was calculated as Rs. 245 and it was Rs. 329 in the case of an electric dryer. The life span of the solar dryer was assumed to be 20 years. The cumulative present worth of annual savings over the life of the solar dryer was calculated for blanched potato chips drying, and it turned out be Rs.163177.67/- which was much higher than the capital cost of the dryer (Rs. 25000). The payback period was calculated as 0.89 years, which was also very small considering the life of the system (20 years). (author)

MICROBIOLOGICAL CHARACTERISTICS OF THE AIR BLOWN BY WARM AIR HAND DRYERS

Directory of Open Access Journals (Sweden)

Recai OÐUR; Omer Faruk TEKBAS; Osman HANCI; Umut OZCAN

2005-02-01

Full Text Available The aim of the study was to determine the microbiological characteristics of air blown from warm air hand dryers, and to compare findings with the microbiological characteristics of indoor air in which the dryer settled. Air samples was taken from different public places (shopping centers, restaurants and hospitals and investigated for total viable counts, coagulase negative Staphylococcus, E. Coli, Staphylococcus aureus and enteric pathogens. There were differences between sampling indoor places for some of the microorganisms, but all of the air samples taken from dryers contained more microorganisms than indoor air, and the differences between hand dryers and indoor air were statistically significant (p<0.05 except for enteric pathogens. As a result it could be said that warm air hand dryers could be microbiological contamination sources in restrooms or the other places that they are used. [TAF Prev Med Bull 2005; 4(1.000: 1-7

Energy Expenditure in Rock/Pop Drumming

OpenAIRE

De La Rue, S; Draper, Stephen B; Potter, Christopher R; Smith, M.

2013-01-01

Despite the vigorous nature of rock/pop drumming, there are no precise data on the energy expenditure of this activity. The aim of this study was to quantify the energy cost of rock/pop drumming. Fourteen male drummers (mean +/- SD; age 27 +/- 8 yrs.) completed an incremental drumming test to establish the relationship between energy expenditure and heart rate for this activity and a ramped cycle ergometer test to exhaustion as a criterion measure for peak values (oxygen uptake and heart rate...

Active Drumming Experience Increases Infants' Sensitivity to Audiovisual Synchrony during Observed Drumming Actions.

Directory of Open Access Journals (Sweden)

Sarah A Gerson

Full Text Available In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early music perception and cognition.

Active Drumming Experience Increases Infants’ Sensitivity to Audiovisual Synchrony during Observed Drumming Actions

Science.gov (United States)

Timmers, Renee; Hunnius, Sabine

2015-01-01

In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this training, relative to no training, on their later perception of the synchrony between audio and visual presentation of the drumming action. In a second experiment, we then contrasted this active experience with the observation of drumming in order to test whether observation of the audiovisual effect was as effective for sensitivity to multimodal synchrony as active experience. Our results indicated that active experience provided a unique benefit above and beyond observational experience, providing insights on the embodied roots of (early) music perception and cognition. PMID:26111226

Simulating Lahars Using A Rotating Drum

Science.gov (United States)

Neather, Adam; Lube, Gert; Jones, Jim; Cronin, Shane

2014-05-01

complex flow geometry and process of erosion and deposition seen in our high speed videos is more complicated than previously reported in the literature. We identify two layers only in the slowest flows (< 0.5 rad s-1), while faster ones (< 4 rad s-1) include between three and five. As the rotational velocity of the drum increases, the curvature of the free surface increases. In the central part of the drum, the primary interfaces occasionally merges into an elliptical zone rather than a linear shear boundary. Inside this zone is a complete circulation of material. These zones' size and number appears to be a function of the rotational velocity of the drum. These "Neather cells" (as we tentatively name these phenomena) can reach as large as 20 mm in thickness. The centre of mass' deflection from vertical is linearly dependent on rotational velocity, whilst the typical flow regimes as identified by Mellmann [2001] show no influence. The frequency of avalanches increases with velocity up to a critical velocity (approximately 1.1 rad s-1), after which the avalanche frequency remains constant. 1 References J Mellmann. The transverse motion of solids in rotating cylinders-forms of motion and transition behavior. Powder Technology, 118(3):251-270, 2001.

Drying of Rosella (Hibiscus sabdariffa) Flower Petals using Solar Dryer with Double Glass Cover Collector

OpenAIRE

Tjukup Marnoto

2014-01-01

Chemical ingredients in rosella petals are very beneficial for health. Rosella petals needed to be drained for storage and packing purpose. The traditional drying takes 5 days and less healthy. Solar dryer technology can speed up the drying process and protect materials from dust contamination. Solar dryer with double glass covered collector has been designed and made for drying of agricultural products such as rosella flowers. Rosella petals as much as 2300 grams with initial moisture conten...

Rotary drum for distilling bituminous material

Energy Technology Data Exchange (ETDEWEB)

1921-11-02

A rotary drum with insert tubes for distilling bituminous materials, like mineral coal, brown coal, wood, peat, and oil-shale, is characterized in that the insert tube is heated also by superheated steam introduced into the drum.

Small-Scale Experiments.10-gallon drum experiment summary

Energy Technology Data Exchange (ETDEWEB)

Rosenberg, David M.

2015-02-05

A series of sub-scale (10-gallon) drum experiments were conducted to characterize the reactivity, heat generation, and gas generation of mixtures of chemicals believed to be present in the drum (68660) known to have breached in association with the radiation release event at the Waste Isolation Pilot Plant (WIPP) on February 14, 2014, at a scale expected to be large enough to replicate the environment in that drum but small enough to be practical, safe, and cost effective. These tests were not intended to replicate all the properties of drum 68660 or the event that led to its breach, or to validate a particular hypothesis of the release event. They were intended to observe, in a controlled environment and with suitable diagnostics, the behavior of simple mixtures of chemicals in order to determine if they could support reactivity that could result in ignition or if some other ingredient or event would be necessary. There is a significant amount of uncertainty into the exact composition of the barrel; a limited sub-set of known components was identified, reviewed with Technical Assessment Team (TAT) members, and used in these tests. This set of experiments was intended to provide a framework to postulate realistic, data-supported hypotheses for processes that occur in a “68660-like” configuration, not definitively prove what actually occurred in 68660.

A method to quantify tritium inside waste drums: He{sup 3} ingrowth method

Energy Technology Data Exchange (ETDEWEB)

Godot, A.; Lepeytre, C.; Hubinois, J.C. [CEA Valduc, Dept. Traitement Materiaux Nucleaires, Service Analyses- Dechets, Lab. Chimie Analytique, 21 - Is-sur-Tille (France); Arseguel, A.; Daclin, J.P.; Douche, C. [CEA Valduc, Dept. Traitement Materiaux Nucleaires, Service Analyses- Dechets, Lab. de Gestion des Dechets Trities, 21 - Is-sur-Tille (France)

2008-07-15

This method enables an indirect, non intrusive and non destructive measurement of the Tritium activity in wastes drums. The amount of tritium enclosed inside a wastes drum can be determined by the measurement of the leak rate of {sup 3}He of this latter. The simulation predicts that a few months are necessary for establishing the equilibrium between the {sup 3}He production inside the drum and the {sup 3}He drum leak. In practice, after one year of storage, sampling {sup 3}He outside the drum can be realized by the mean of a confining chamber that collect the {sup 3}He outflow. The apparatus, the experimental procedure and the calculation of tritium activity from mass spectrometric {sup 3}He measurements are detailed. The industrial device based on a confinement cell and the automated process to measure the {sup 3}He amount at the initial time and after the confinement time is described. Firstly, reference drums containing a certified tritium activity (HTO) in addition to organic materials have been measured to qualify the method and to evaluate its performances. Secondly, tritium activity of organic wastes drums issued from the storage building in Valduc have been determined. Results of the qualification and optimised values of the experimental parameters are reported in order to determine the performances of this industrial device. As a conclusion, the apparatus enables the measurement of an activity as low as 1 GBq of tritium in a 200 liters drum containing organic wastes. (authors)

Infrared thermography applied to monitoring of radioactive waste drums

International Nuclear Information System (INIS)

Kelmer, P.; Camarano, D.M.; Calado, F.; Phillip, B.; Viana, C.; Andrade, R.M.

2013-01-01

The use of thermography in the inspection of drums containing radioactive waste is being stimulated by the absence of physical contact. In Brazil the majority of radioactive wastes are compacted solids packed in metal drums stored temporarily for decades and requires special attention. These drums have only one qualitative indication of the radionuclides present. However, its structural condition is not followed systematically. The aim of this work is presents a methodology by applying thermography for monitoring the structural condition of drums containing radioactive waste in order to detect degraded regions of the drums. (author)

Monte Carlo method to characterize radioactive waste drums

International Nuclear Information System (INIS)

Lima, Josenilson B.; Dellamano, Jose C.; Potiens Junior, Ademar J.

2013-01-01

Non-destructive methods for radioactive waste drums characterization have being developed in the Waste Management Department (GRR) at Nuclear and Energy Research Institute IPEN. This study was conducted as part of the radioactive wastes characterization program in order to meet specifications and acceptance criteria for final disposal imposed by regulatory control by gamma spectrometry. One of the main difficulties in the detectors calibration process is to obtain the counting efficiencies that can be solved by the use of mathematical techniques. The aim of this work was to develop a methodology to characterize drums using gamma spectrometry and Monte Carlo method. Monte Carlo is a widely used mathematical technique, which simulates the radiation transport in the medium, thus obtaining the efficiencies calibration of the detector. The equipment used in this work is a heavily shielded Hyperpure Germanium (HPGe) detector coupled with an electronic setup composed of high voltage source, amplifier and multiport multichannel analyzer and MCNP software for Monte Carlo simulation. The developing of this methodology will allow the characterization of solid radioactive wastes packed in drums and stored at GRR. (author)

The design, construction, and operation of the Integrated Radwaste Treatment System (IRTS) Drum Cell

International Nuclear Information System (INIS)

Landau, B.; Russillo, A.; Frank, D.; Garland, D.

1989-12-01

This report describes the design, construction, and the operation of the Integrated Radwaste Treatment Systems (IRTS) Drum Cell at the West Valley Demonstration Project (WVDP), West Valley, New York. The IRTS Drum Cell was designed to provide a shielded, secure storage area for the remote handling and placement of low-level Class C radioactive waste produced in the IRTS. The Drum Cell was designed to contain up to approximately 8,804 drums from decontaminated supernatant processing. This waste is to be poured into 0.27m 3 in a temperature controlled environment to ensure the cement will not be subjected to freezing and thawing cycles. A Temporary Weather Structure (TWS), a pre-engineered building, now encloses the Drum Cell and associated equipment so that remote waste-handling and placement operations can continue without regard to weather conditions. The Drum Cell was designed so that this TWS could be removed and the low-level waste entombed in place. Final disposition of this low-level waste is currently being evaluated in an Environmental Impact Statement (EIS). 10 refs., 11 figs., 1 tab

21 CFR 886.4230 - Ophthalmic knife test drum.

Science.gov (United States)

2010-04-01

... 21 Food and Drugs 8 2010-04-01 2010-04-01 false Ophthalmic knife test drum. 886.4230 Section 886...) MEDICAL DEVICES OPHTHALMIC DEVICES Surgical Devices § 886.4230 Ophthalmic knife test drum. (a) Identification. An ophthalmic knife test drum is a device intended to test the keenness of ophthalmic surgical...

Experimental Investigation on an Energy Efficient Solar Tunnel Dryer

OpenAIRE

M. R. Seshan Ram

2012-01-01

The research determines the effectiveness of the solar tunnel dryer developed and the product dried in the device is superior in quality and also it is compatible with branded products available in the market. The study also determines Acetamide as Phase Key words: Solar Tunnel Dryer, Acetamide as Phase Change Materials, Conversion into Thermal Energy, Thermocouple, and Pyranometer

Alternatives to reduce corrosion of carbon steel storage drums

International Nuclear Information System (INIS)

Zirker, L.R.; Beitel, G.A.

1995-11-01

The major tasks of this research were (a) pollution prevention opportunity assessments on the overpacking operations for failed or corroded drums, (b) research on existing container corrosion data, (c) investigation of the storage environment of the new Resource Conservation and Recovery Act Type II storage modules, (d) identification of waste streams that demonstrate deleterious corrosion affects on drum storage life, and (e) corrosion test cell program development. Twenty-one waste streams from five US Department of Energy (DOE) sites within the DOE Complex were identified to demonstrate a deleterious effect to steel storage drums. The major components of these waste streams include acids, salts, and solvent liquids, sludges, and still bottoms. The solvent-based waste streams typically had the shortest time to failure: 0.5 to 2 years. The results of this research support the position that pollution prevention evaluations at the front end of a project or process will reduce pollution on the back end

Modeling unsteady-state VOC transport in simulated waste drums

International Nuclear Information System (INIS)

Liekhus, K.J.; Gresham, G.L.; Peterson, E.S.; Rae, C.; Hotz, N.J.; Connolly, M.J.

1994-01-01

This report is a revision of an EG ampersand G Idaho informal report originally titled Modeling VOC Transport in Simulated Waste Drums. A volatile organic compound (VOC) transport model has been developed to describe unsteady-state VOC permeation and diffusion within a waste drum. Model equations account for three primary mechanisms for VOC transport from a void volume within the drum. These mechanisms are VOC permeation across a polymer boundary, VOC diffusion across an opening in a volume boundary, and VOC solubilization in a polymer boundary. A series of lab-scale experiments was performed in which the VOC concentration was measured in simulated waste drums under different conditions. A lab-scale simulated waste drum consisted of a sized-down 55-gal metal drum containing a modified rigid polyethylene drum liner. Four polyethylene bags were sealed inside a large polyethylene bag, supported by a wire cage, and placed inside the drum liner. The small bags were filled with VOC-air gas mixture and the VOC concentration was measured throughout the drum over a period of time. Test variables included the type of VOC-air gas mixtures introduced into the small bags, the small bag closure type, and the presence or absence of a variable external heat source. Model results were calculated for those trials where the permeability had been measured

Space-DRUMS trade mark sign experimental development using parabolic reduced gravity flights

International Nuclear Information System (INIS)

Guigne, J.Y.; Millan, D.; Davidson, R.

2000-01-01

Space-DRUMS trade mark sign is a microgravity containerless-processing facility that uses acoustic beams to position large diameter liquid or solid samples within a gas-filled chamber. Its capacity to control the position of large diameter (6 cm) low density solid materials was successfully demonstrated on NASA's DC-9 parabolic aircraft in July 1996; two subsequent flights occurred in 1998 using the KC-135 and A-300 aircraft to further refine the technology used in the system. The working environment for the Space-DRUMS trade mark sign facility is the Space Shuttle/Space Station where long duration microgravity experimentation can take place. Since the reduced gravity environment of an A-300 or a KC-135 parabolic flight is much harsher than that of the Space Shuttle in terms of residual acceleration magnitudes experienced by the samples to be held in position; this more extreme environment allows for most Space-DRUMS trade mark sign technical payload functionality tests to be conducted. In addition to flight hardware shakedowns, parabolic flights continue to be extensively used to study and evaluate the behavior of candidate-advanced materials proposed for ISS Space-DRUMS trade mark sign campaigns. The first samples to be processed in 2001 involve combustion synthesis (also known as SHS - Self-propagating High Temperature Synthesis) of large glass-ceramic and of porous ceramic spheres. Upmassing Space-DRUMS trade mark sign for the International Space Station is scheduled for early 2001

A model for the thermodynamic analysis in a batch type fluidized bed dryer

International Nuclear Information System (INIS)

Özahi, Emrah; Demir, Hacımurat

2013-01-01

An original model for thermodynamic analysis of a batch type fluidized bed dryer is proposed herein considering two separate systems comprised of drying air medium as a control volume and particles to be dried as a control mass. By means of the proposed model, energetic and exergetic analyses of a drying column of a batch type fluidized bed dryer are carried out as an original contribution to literature since there is no such like model in which the analyses are performed considering two separate systems. The energetic efficiencies evaluated by means of the proposed model using the data in literature are compared with those in literature and a good conformity is satisfied with an acceptable error margin of ±9%. A new correlation is also developed with a mean deviation of ±10% in order to evaluate the energetic efficiency for not only corn drying process but also drying processes of other particles at inlet air temperature of 50 °C. Effects of air mass flow rate, mass of particle and ambient temperature on energetic and exergetic efficiencies are analyzed and some concluding remarks are highlighted for further studies. - Highlights: • Energetic and exergetic analyses of a batch type fluidized bed dryer are developed. • An original model is proposed for thermodynamic analyses in a fluidized bed dryer. • The proposed model is compared with the data in literature with an accuracy of ±9%. • Effect of air mass flow rate is more significant than that of ambient temperature. • Effect of mass of particle is more significant than that of ambient temperature

Heat load limits for TRU drums on pads

International Nuclear Information System (INIS)

Steimke, J.L.; McKinley, M.S.

1993-08-01

Some of the Trans-Uranic (TRU) waste generated at SRS is packaged in 55 gallon, galvanized steel drums and stored on concrete pads that are exposed to the weather. It was necessary to compute how much heat can be generated by the waste in these drums without exceeding the temperature limits of the contents of the drum. This report documents the calculation of heat load limits for the drum, which depend on the temperature limits of the contents of the drum. The applicable temperature limits for the contents of the drum are the melting temperature of the polyethylene liner, 284 ± 8 F, the combustion temperature of paper, 450 F and the decomposition temperature of anionic resin, 190 F. One part of the analysis leading to the heat load limits was the collection of weather records on solar flux, wind speed and air temperature. Another part of the task was an experimental measurement of two important properties of the drum lid, the emittance and the absorptance. As used here, emittance is the rate at which an object emits infrared thermal radiation divided by the rate at which a perfect black body at the same temperature emits thermal radiation. Absorptance is the rate at which an object absorbs solar radiation divided by the rate at which a perfect black body absorbs radiation. For nine locations on each of eight typical weathered drum lids the measured emittance ranged from 0.73 ± 0.05 to 1.00 ± 0.07 (95% confidence level) and the average emittance for the eight lids was 0.85. For the eight drum lids the measured absorptance ranged from 0.64 ± 0.07 to 0.79 ± 0.07 with an average absorptance for the eight lids of 0.739

Rotary drum for a centrifugal separator

International Nuclear Information System (INIS)

Fukai, Tamotsu.

1970-01-01

Herein provided is a rotary drum designed to prevent strength reduction and eccentric weight redistribution at the joints between the drum body and the end cups therefore when materials having divergent specific gravities, strengths and Young's Modulus are employed as the construction materials for the drum body and end cups. The drum body is fabricated by combining glass, carbon boron or similar high strength fibers with a thermosetting hardenable resin. This composite material is then molded into the finished cylindrical product the ends of which are bent slightly inward to receive a rigid, high-strength, ring-shaped end fitting to be integrally joined thereto during the molding operation. Each ring is further adapted to retain an end cap by a procedure which entails lowering the temperature of the end cap and applying heat to the ring, thus joining both members tightly together by employing the differences in thermal expansion of each. (Owens, K. J.)

Effect of brining on the drying rate of tilapia in a solar tunnel dryer

Energy Technology Data Exchange (ETDEWEB)

Kituu, G.M.; Shitanda, D.; Kanali, C.L.; Mailutha, J.T. [Jomo Kenyatta Univ. of Agriculture and Technology, Nairobi (Kenya). BEED

2008-07-01

In addition to being a source of protein, fish is an important source of local and foreign currency earnings in Kenya. A substantial amount of fish production is exported. Approximately 30 per cent is exported to the European Union, the United States, and countries in the Middle East, but nearly half of the total annual fish harvest in Kenya goes to waste due to poor processing and preservation. Measures must be taken to ensure the fish industry is protected and waste is minimized, since the livelihood of over 500,000 people depends on fish as a source of proteins and employment. Therefore, it is necessary to implement appropriate and affordable processing and preservation techniques for fish at the artisanal landing sites in order to reduce the wastage and spoilage of fish during oversupply, and to enhance long storage. This paper presented studies that were conducted to determine the effect of brining on the drying rate of tilapia in a solar tunnel dryer. The paper discussed the materials and methods, including a description of the solar tunnel dryer system; the brining process of fish; the fish drying process; and data analysis. It was concluded that limiting the amount of salt used in brining, and subsequently dehydrating fish with a solar tunnel dryer achieves a more stable and suitable dried fish product than osmotic dehydration or solar drying process separately. 19 refs., 5 figs., 2 appendices.

Modeling and simulation of milk emulsion drying in spray dryers

Directory of Open Access Journals (Sweden)

V. S. Birchal

2005-06-01

Full Text Available This work aims at modeling and simulating the drying of whole milk emulsion in spray dryers. Drops and particles make up the discrete phase and are distributed into temporal compartments following their residence time in the dryer. Air is the continuous and well-mixed phase. Mass and energy balances are developed for each phase, taking into account their interactions. Constitutive equations for describing the drop swelling and drying mechanisms as well as the heat and mass transfer between particles and hot air are proposed and analyzed. A set of algebraic-differential equations is obtained and solved by specific numerical codes. Results from experiments carried out in a pilot spray dryer are used to validate the model developed and the numerical algorithm. Comparing the simulated and experimental data, it is shown that the model predicts well the individual drop-particle history inside the dryer as well as the overall outlet air-particle temperature and humidity.

Examination of representative drum from 618-9 Burial Ground

International Nuclear Information System (INIS)

Duncan, D.R.; Bunnell, L.R.

1992-10-01

The work described in this report was conducted in pursuance of Task E of the Pacific Northwest Laboratory Solid Waste Technology Support Program for Westinghouse Hanford Company. Task E calls for a determination of the corrosion rate of low-carbon steels under typical Hanford Site conditions. To meet this objective, Pacific Northwest Laboratory examined one intact drum that was judged to be representative of the largely intact drums excavated at the 618-9 Burial Ground located west of the 300 Area at the Hanford Site. Six samples were examined to characterize the drum, its composition, and its corrosion and corrosion products. The drum, which was found empty, was constructed of low-carbon steel. Its surface appeared relatively sound. The drum metal varied in thickness, but the minimum thickness in the samples was near 0.020 in. The corrosion corresponds to approximately 25 to 35 mils of metal loss, roughly a 1 mil/yr corrosion rate. Corrosion products were goethite and maghymite, expected products of iron buried in soil. Apparently, the drum leaked some time ago, but the cause of the leakage is unknown because records of the drums and their burial are limited. The drum was empty when found, and it is possible that it could have failed by pitting rather than by general corrosion. A pitting rate of about 3.5 mils/yr would have caused loss of drum integrity in the time since burial

Qualitative and quantitative analysis of plutonium in solid waste drums

International Nuclear Information System (INIS)

Anno, Jacques; Escarieux, Emile

1977-01-01

An assessment of the results given by a study carried out for the development of qualitative and quantitative analysis, by γ spectrometry, of plutonium in solid waste drums is presented. After having reminded the standards and their incidence on the quantities of plutonium to be measured (application at industrial Pu: 20% of Pu 240 ) the equipment used is described. Measurement station provided with a mechanical system consisting of: a rail and a pulley block to bring the drums; a pit and a hydraulic jack with a rotating platform. The detection instrumentation consisting of: a high volume coaxial Ge(Li) detector with a γ ray resolution of 2 keV; an associated electronic; a processing of data by a 'Plurimat 20' minicomputer. Principles of the identification and measurements are specified and supported by experimental results. They are the following: determination of the quality of Pu by measuring the ratio between the γ ray intensities of the 239 Pu 129 keV and of the 241 Pu 148 keV; measurement of the 239 Pu mass by estimating the γ ray counting rate of the 375 keV from the calibrating curves given by plutonium samples varying from 32 mg to 80 g; correction of the results versus the source position into the drum and versus the filling in plastic materials into this drum. The experimental results obtained over 40 solid waste drums are presented along with the error estimates [fr

Herbs drying using a heat pump dryer

Energy Technology Data Exchange (ETDEWEB)

Fatouh, M.; Metwally, M.N.; Helali, A.B.; Shedid, M.H. [Department of Mechanical Power Engineering, Faculty of Engineering at El Mattaria, Helwan University, P.O. Box 11718, Masaken El-Helmia, Cairo (Egypt)

2006-09-15

In the present work, a heat pump assisted dryer is designed and constructed to investigate the drying characteristics of various herbs experimentally. R134a is used as a working fluid in the heat pump circuit during the experimental work. Experiments have been conducted on Jew's mallow, spearmint and parsley. The effects of herb size, stem presence, surface load, drying air temperature and air velocity on the drying characteristics of Jew's mallow have been predicted. Experimental results show that a high surface load of 28kg/m{sup 2} yields the smallest drying rate, while the drying air with temperature of 55{sup o}C and velocity of 2.7m/s achieves the largest drying rate. A maximum dryer productivity of about 5.4kg/m{sup 2}h is obtained at the air temperature of 55{sup o}C, air velocity of 2.7m/s and dryer surface load of 28kg/m{sup 2}. It was found that small size herbs without stem need low specific energy consumption and low drying time. Comparison of the drying characteristics of different herbs revealed that parsley requires the lowest specific energy consumption (3684kJ/kg{sub H{sub 2}O}) followed by spearmint (3982kJ/kg{sub H{sub 2}O}) and Jew's mallow (4029kJ/kg{sub H{sub 2}O}). Finally, dryer productivity has been correlated in terms of surface load, drying air velocity and drying air temperature. (author)

The Welding Effect on Mechanical Strength of Low Level Radioactive Waste Drum Container

International Nuclear Information System (INIS)

Aisyah; Herlan Martono

2007-01-01

The treatment of compactable low level solid waste was started by compaction of 100 liter drum containing the waste using 600 kN hydraulic press in 200 liters drum. The 200 liter drum of waste container containing of compacted waste then immobilized with cement and stored in interm storage. The 200 liter drum of waste container made of carbon steel material to comply with a good mechanical strength request in order to be able to retain the waste content for long period. Welding is a one step in a waste drum container fabrication process that has an opportunity in decreasing these mechanical strength. The research is carried out by welding the waste drum container material sample by electric arc welding. Mechanical strength test carried out by measuring the tensile strength by using the tensile strength machine, hardness test by using Vickers hardness test and microstructure observation by using the optic microscope. The result shows that the welding cause the microstructure changes, its meaning of forming ferro oxide phase on welding area that leads to the brittle material, so that the mechanical strength has a decreasing slightly. Nevertheless the decreasing of mechanical strength is still in the range of safety limit. (author)

30 CFR 77.307 - Thermal dryers; location and installation; general.

Science.gov (United States)

2010-07-01

... where the heat, sparks, flames, or coal dust from the system might cause a fire or explosion. (b... LABOR COAL MINE SAFETY AND HEALTH MANDATORY SAFETY STANDARDS, SURFACE COAL MINES AND SURFACE WORK AREAS OF UNDERGROUND COAL MINES Thermal Dryers § 77.307 Thermal dryers; location and installation; general...

Hand dryer noise in public restrooms exceeds 80 dBA at 10 ft (3 m

Directory of Open Access Journals (Sweden)

Shari Salzhauer Berkowitz

2015-01-01

Full Text Available High airflow hand dryers are found in many public restrooms today. These dryers offer quick and clean hand drying, and are seen as being an environment-friendly alternative to paper towels. However, many new hand dryers are loud, exposing individuals using the facilities as well as those employees who clean the facilities to potentially dangerous noise. Prolonged exposure to high levels of occupational noise can cause damage to hair cells in the cochlea, resulting in varying degrees of noise-induced hearing loss. This study examined the intensity (in dBA of the noise produced by the air dryers in campus restrooms. Hand dryer peak and average noise was measured with a sound level meter at 2.5 ft, 5 ft, and 10 ft from the dryer. Noise measurements did not decrease as predicted by the inverse-square law, probably because of the reverberative surfaces found in the restrooms. The small sample of hand dryers tested was mostly found to be producing more noise than the manufacturer claimed they would; indeed, none of the dryers would be safe for an 8-h workday exposure. While hand dryers do reduce paper trash, they pose as a different sort of hazard to our environment and population.

Modeling of thermal mode of drying special purposes ceramic products in batch action chamber dryers

Science.gov (United States)

Lukianov, E. S.; Lozovaya, S. Yu; Lozovoy, N. M.

2018-03-01

The article is devoted to the modeling of batch action chamber dryers in the processing line for producing shaped ceramic products. At the drying stage, for various reasons, most of these products are warped and cracked due to the occurrence of irregular shrinkage deformations due to the action of capillary forces. The primary cause is an untruly organized drying mode due to imperfection of chamber dryers design specifically because of the heat-transfer agent supply method and the possibility of creating a uniform temperature field in the whole volume of the chamber.

Performances of continuous dryer with inert medium fluidized bed

Directory of Open Access Journals (Sweden)

Arsenijević Zorana Lj.

2008-01-01

Full Text Available A fluid bed dryer with inert particles represents a very attractive alternative to other drying technologies according to the main efficiency criteria, i.e. specific water evaporation rate, specific heat consumption and speci­fic air consumption. A high drying efficiency results from the large con­tact area and from the large temperature difference between the inlet and outlet air. A rapid mixing of the particles leads to nearly isothermal conditions throughout the bed. A fluid bed dryer with inert particles was used for drying of slurries. Experiments were performed in a cylindrical column 215 mm in diameter with glass spheres as inert particles. In this paper, results of drying experi­ments with slurries of Zineb fungicide, copper hydroxide, calcium carbo­nate and pure water used as the feed material are presented. In our fluidized bed we successfully dried a number of other materials such as: fungicides and pesticides (Ziram, Propineb, Mangozeb, copper oxy-chloride, copper oxy-sulphate, Bordeaux mixture, other inorganic compounds (calcium sulphate, cobalt carbonate, electrolytic copper, sodium chloride, and a complex compound (organo-bentonite. The effects of operating conditions on dryer throughput and product quality were investigated. Main performance criteria, i.e. specific water evaporation rate, specific heat consumption and specific air consumption, were quantified. Temperature profile along the bed was mapped, and nearly isothermal conditions were found due to thorough mixing of the particles. Analysis of drying and energy efficiencies as a function of inlet and outlet air temperature difference was performed for deeper insight in dryer behavior and for optimizing dryer design and operation from an energy point of view. A simple mathematical model based on an overall heat balance predicts the dryer performance quite well. The industrial prototype with fluid bed of 0.8 m in diameter and capacity 650 kg of evaporated moisture per

Experimental silo-dryer-aerator for the storage of soybean grains

Directory of Open Access Journals (Sweden)

Paulo C. Coradi

Full Text Available ABSTRACT This study aimed to verify the capacity of silo-dryer-aerator prototype equipment operating as a silo-storage-aerator for soybean quality analysis. Soybeans with water content of 17% (wet basis – w.b. were dried and stored in a silo-dryer-aerator system that was designed using a drying chamber, four independent storage cells, and a static capacity of 164 kg. Another batch of grains was stored in a silo-storage-aerator with a capacity of 1,200 kg. The experiment was set up in a completely randomized factorial 5 × 4 experimental design including five grain batches stored after being dried at 30, 40, and 50 °C (mixed grains were dried at three temperatures in the silo-dryer-aerator cells and one mixed grain batch stored in the silo-storage-aerator system under ambient air conditions for four storage times (zero, one, two, and three months. There was no difference between the grains stored in the silo-dryer-aerator and silo-storage-aerator at the end of the three-month storage in terms of the physico-chemical quality. The storage time associated with drying at 50 °C caused a reduction in the physical-chemical quality of the grains. The silo-dryer-aerator system was presented as a possible alternative to store soybean (Glycine max L. grains.

Case studies of corrosion of mixed waste and transuranic waste drums

International Nuclear Information System (INIS)

Kosiewicz, S.T.

1993-01-01

This paper presents three case studies of corrosion of waste drums at the Los Alamos National Laboratory (LANL). Corrosion was not anticipated by the waste generators, but occurred because of subtle chemical or physical mechanisms. In one case, drums of a cemented transuranic (TRU) sludge experienced general and pitting corrosion. In the second instance, a chemical from a commercial paint stripper migrated from its primary containment drums to chemically attack overpack drums made of mild carbon steel. In the third case, drums of mixed low level waste (MLLW) soil corroded drum packaging even though the waste appeared to be dry when it was placed in the drums. These case studies are jointly discussed as ''lessons learned'' to enhance awareness of subtle mechanisms that can contribute to the corrosion of radioactive waste drums during interim storage

Model-Based Energy Efficiency Optimization of a Low-Temperature Adsorption Dryer

NARCIS (Netherlands)

Atuonwu, J.C.; Straten, G. van; Deventer, H.C. van; Boxtel, A.J.B. van

2011-01-01

Low-temperature drying is important for heat-sensitive products, but at these temperatures conventional convective dryers have low energy efficiencies. To overcome this challenge, an energy efficiency optimization procedure is applied to a zeolite adsorption dryer subject to product quality. The

Low cost solar dryer for fish

African Journals Online (AJOL)

Administrator

Department of Electrical and Other Energy Sources, College of Agricultural Engineering and Technology, DBSKKV, ... The average solar energy ranged between 450 - 500 ..... classification and selection of dryers, In Handbook of industrial.

76 FR 22324 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2011-04-21

... standards, the current standards for room air conditioners and clothes dryers, and the history of the... Residential Clothes Dryers and Room Air Conditioners AGENCY: Office of Energy Efficiency and Renewable Energy... equipment, including residential clothes dryers and room air conditioners. EPCA also requires the U.S...

The Saami shaman drums: some reflexions from an archaelogical perspective

Directory of Open Access Journals (Sweden)

Inger Zachrisson

1991-01-01

Full Text Available The Saami shaman drums from northern Scandinavia can be discussed from many different points of view. For an archaeologist there are other questions of interest than those which generally occupy the historian of religions. One important question is how old the known Saami drums are. The known drums are as a rule assumed to be from the seventeenth or the eighteenth centuries, when most of them were collected. It has also been thought that, because of the materials they are made of, drums could not have been preserved any longer. Another perhaps more interesting question is how old the known types of Saami drums might be. When did they acquire their 'classical' form? What did the Viking Age Saami drums look like?

The Saami shaman's drum and the star horizons

Directory of Open Access Journals (Sweden)

Bo Sommarström

1991-01-01

Full Text Available The aim of this contribution is to examine the possible influences of stellar constellations on the positioning of the drum figures on the drums used by the Saami people during the 17th and 18th centuries. Certain of the drum figures seem to have a similar position to corresponding figures on traditional star maps, both with respect to single star constellations and to some members of the Zodiac circle. The most general correspondences between star maps and the painted designs on drums depend on the existence of a cross for determining the four cardinal points in both cases. The star constellations compared here with the drum-figures are in fact peripheral Saami skies. It is hard to believe that they can have played any vital role in their capacity as star symbols within the frame of the Saamis' own astral cosmology. It is more probable that the earthly meanings of most of the figures were more important to the drummer.

Safety analysis report for packaging (onsite) steel drum

International Nuclear Information System (INIS)

McCormick, W.A.

1998-01-01

This Safety Analysis Report for Packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the steel drum packaging system meets the transportation safety requirements of HNF-PRO-154, Responsibilities and Procedures for all Hazardous Material Shipments, for an onsite packaging containing Type B quantities of solid and liquid radioactive materials. The basic component of the steel drum packaging system is the 208 L (55-gal) steel drum

Performance of mechanically shaken indirect contact atmospheric dryer in drying pastelike materials

Directory of Open Access Journals (Sweden)

K. P. Melo

2004-09-01

Full Text Available Pastelike materials are encountered in many technological processes in chemical, pharmaceutical, foodstuff and natural product industries. The most important factor in the drying of this type of materials is the nature of the moisture bonding that occurs. Because of the different characteristics of pastes, it is impossible to recommend a universal type of dryer for all of these materials. Some of the dryers available provide only indirect contact with the drying agent (heat and also maintain constant moisture with a system of rotating paddles. We evaluated the performance of this type by studying the dryer kinetics curves for ground coffee under a variety of operational conditions of moisture load of material, temperature of the heating plate, intensity of the mechanical mixing of the moisture material, and initial moisture. The effects of these parameters (except for moisture were studied using a 2³ factorial design. According the analyses of the kinetics drying curves, was observed that the increase in the temperature of the plate and rotation as well as the decrease in the load facilitates more effective removal of moisture. In statistical analysis was determined that the load of the material and the heating plate temperature influence the final moisture content of the material and plate temperature modifies the final temperature of the solid. Also, was suggested linear models from the factorial design to describe the process of drying coffee grounds satisfactorily.

Source Test Report for the 205 Delayed Coking Unit Drum 205-1201 and Drum 205-1202 Depressurization Vents (Marathon Petroleum Company LLC)

Science.gov (United States)

The 2010 Source Test was performed during the atmospheric depressurization step of the delayed coking process prior to the removal of petroleum coke from the coke drum. The 205 DCU was operated under a variety of conditions during the 2010 Source Test.

The Design And Development Of Solar Maize Dryer With Subsidiary ...

African Journals Online (AJOL)

A solar Dryer with a subsidiary heating source for drying maize seed is designed and constructed. The dryer is made up a solar collector (heat source), the drying chamber (Product storage), and a subsidiary heating source (local oil). The plant when put in operation by expositing it to the solar rays, is capable of attaining a ...

ENERGY STAR Certified Residential Clothes Dryers

Data.gov (United States)

U.S. Environmental Protection Agency — Certified models meet all ENERGY STAR requirements as listed in the Version 1.1 ENERGY STAR Program Requirements for Clothes Dryers that are effective as of January...

A greenhouse type solar dryer for small-scale dried food industries: Development and dissemination

Energy Technology Data Exchange (ETDEWEB)

Janjai, Serm [Solar Energy Research Laboratory, Department of Physics, Faculty of Science, Silpakorn University, Nakhon Pathom 73000 (Thailand)

2012-07-01

In this study, a greenhouse type solar dryer for small-scale dried food industries was developed and disseminated. The dryer consists of a parabolic roof structure covered with polycarbonate sheets on a concrete floor. The system is 8.0m in width, 20.0m in length and 3.5m in height, with a loading capacity about 1,000kg of fruits or vegetables. To ensure continuous drying operation, a 100kW-LPG gas burner was incorporated to supply hot air to the dryer during cloudy or rainy days. Nine 15-W DC fans powered by three 50-W PV modules were used to ventilate the dryer. This dryer was installed for a small-scale food industry at Nakhon Pathom in Thailand to produce osmotically dehydrated tomato. To investigate its performance, the dryer was used to dry 3 batches of osmotically dehydrated tomato. Results obtained from these experiments showed that drying air temperatures in the dryer varied from 35 C to 65 C. In addition, the drying time for these products was 2-3 days shorter than that of the natural sun drying and good quality dried products were obtained. A system of differential equations describing heat and moisture transfers during drying of osmotically dehydrated tomato was also developed. The simulated results agreed well with the experimental data. For dissemination purpose, other two units of this type of dryer were constructed and tested at two locations in Thailand and satisfactory results were obtained.

An improved segmented gamma scanning for radioactive waste drums

International Nuclear Information System (INIS)

Liu Cheng; Wang Dezhong; Bai Yunfei; Qian Nan

2010-01-01

In this paper, the equivalent radius of radioactive sources in each segment is determined by analyzing the different responses of the two identical detectors, and an improved segmented gamma scanning is used to assay waste drums containing mainly organic materials, and proved by an established simulation model. The simulated radioactivity distributions in homogenous waste drum and an experimental heterogeneous waste drum were compared with those of traditional segmented gamma scanning. The results show that our method is good in performance and can be used for analyzing the waste drums. (authors)

Breakage and drying behaviour of granules in a continuous fluid bed dryer: Influence of process parameters and wet granule transfer.

Science.gov (United States)

De Leersnyder, F; Vanhoorne, V; Bekaert, H; Vercruysse, J; Ghijs, M; Bostijn, N; Verstraeten, M; Cappuyns, P; Van Assche, I; Vander Heyden, Y; Ziemons, E; Remon, J P; Nopens, I; Vervaet, C; De Beer, T

2018-03-30

Although twin screw granulation has already been widely studied in recent years, only few studies addressed the subsequent continuous drying which is required after wet granulation and still suffers from a lack of detailed understanding. The latter is important for optimisation and control and, hence, a cost-effective practical implementation. Therefore, the aim of the current study is to increase understanding of the drying kinetics and the breakage and attrition phenomena during fluid bed drying after continuous twin screw granulation. Experiments were performed on a continuous manufacturing line consisting of a twin-screw granulator, a six-segmented fluid bed dryer, a mill, a lubricant blender and a tablet press. Granulation parameters were fixed in order to only examine the effect of drying parameters (filling time, drying time, air flow, drying air temperature) on the size distribution and moisture content of granules (both of the entire granulate and of size fractions). The wet granules were transferred either gravimetrically or pneumatically from the granulator exit to the fluid bed dryer. After a certain drying time, the moisture content reached an equilibrium. This drying time was found to depend on the applied airflow, drying air temperature and filling time. The moisture content of the granules decreased with an increasing drying time, airflow and drying temperature. Although smaller granules dried faster, the multimodal particle size distribution of the granules did not compromise uniform drying of the granules when the target moisture content was achieved. Extensive breakage of granules was observed during drying. Especially wet granules were prone to breakage and attrition during pneumatic transport, either in the wet transfer line or in the dry transfer line. Breakage and attrition of granules during transport and drying should be anticipated early on during process and formulation development by performing integrated experiments on the granulator

Design and Evaluation of Solar Grain Dryer with a Back-up Heater

OpenAIRE

K.S. Tonui; E.B.K. Mutai; D.A. Mutuli; D.O. Mbuge; K.V. Too

2014-01-01

The aim of the study was to design and construct a solar grain dryer integrated with a simple biomass burner using locally available materials. This was to address the limitations of the natural sun drying for example drying exposure, liability to pests and rodents, over-dependence on sun and escalated cost of mechanical dryers. This became beneficial especially in reducing post-harvest losses as well as helping in the preservation of agricultural product. The dryer is composed of solar colle...

75 FR 27504 - Substantial Product Hazard List: Hand-Held Hair Dryers

Science.gov (United States)

2010-05-17

... immersion during their use. Section 15(a) of the CPSA defines ``substantial product hazard'' to include, a....'' Hand-held hair dryers routinely contain open-coil heating elements that are, in essence, uninsulated..., bathtub, or lavatory). The proposed rule would define ``hand-held hair dryer'' as ``an electrical...

Calculation of a thermostressed state for drum-separator vessels in transient regimes

International Nuclear Information System (INIS)

Il'in, Yu.V.; Kazakova, T.Yu.; Parafilo, L.M.; Shcherbakov, S.I.

1979-01-01

The temperature regime and stressed state of the drum-separator vessel in the transient regime with alternating pressure and water level are investigated using calculations. The temperature fields are calculated by the alternating directions method. Stresses and deformations are calculated by the method of finite elements. The stressed state of the vessel is determined for a series of fixed time moments tausub(i), when the T(tausub(i), r, phi) temperature distribution and P(tausub(i)) internal pressure are known. The methods described are used while developing the calculation program for the temperatures and stressed state (FORTRAN, EC-1050). Given are the calculation results obtained using these programs for the processes following the safety system response at the first block of the Bilibinsk NPP and the processes of power regulation in the ''Sever-2'' facility. The comparison of the obtained calculated curves with the experimental data confirms fitness of the proposed calculated scheme for description of the real processes taking place in the drum-separator vessels in the transient regimes. It is emphasized that the given scheme of solution of the equations describing a thermostressed state of the drum-separator vessels can be used while estimating their operation capacity

Source imaging of drums in the APNEA system

International Nuclear Information System (INIS)

Hensley, D.

1995-01-01

The APNea System is a neutron assay device utilizing both a passive mode and a differential-dieaway active mode. The total detection efficiency is not spatially uniform, even for an empty chamber, and a drum matrix in the chamber can severely distort this response. In order to achieve a response which is independent of the way the source material is distributed in a drum, an imaging procedure has been developed which treats the drum as a number of virtual (sub)volumes. Since each virtual volume of source material is weighted with the appropriate instrument parameters (detection efficiency and thermal flux), the final assay result is essentially independent of the actual distribution of the source material throughout the drum and its matrix

Listening to the Shape of a Drum

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 3; Issue 9. Listening to the Shape of a Drum - The Mathematics of Vibrating Drums. S Kesavan. General Article Volume 3 Issue 9 September 1998 pp 26-34. Fulltext. Click here to view fulltext PDF. Permanent link:

Simulation of exhaust gas heat recovery from a spray dryer

International Nuclear Information System (INIS)

Golman, Boris; Julklang, Wittaya

2014-01-01

This study explored various alternatives in improving the energy utilization of spray drying process through the exhaust gas heat recovery. Extensible and user-friendly simulation code was written in Visual Basic for Applications within Microsoft Excel for this purpose. The effects of process parameters were analyzed on the energy efficiency and energy saving in the industrial-scale spray drying system with exhaust gas heat recovery in an air-to-air heat exchanger and in the system with partial recirculation of exhaust air. The spray dryer is equipped with an indirect heater for heating the drying air. The maximum gains of 16% in energy efficiency and 50% in energy saving were obtained for spray drying system equipped with heat exchanger for exhaust air heat recovery. In addition, 34% in energy efficiency and 61% in energy saving for system with recirculation of exhaust air in the present range of process parameters. The high energy efficiency was obtained during drying of large amount of dilute slurry. The energy saving was increased using the large amount of hot drying air. - Highlights: • We model industrial-scale spray drying process with the exhaust gas heat recovery. • We develop an Excel VBA computer program to simulate spray dryer with heat recovery. • We examine effects of process parameters on energy efficiency and energy saving. • High energy efficiency is obtained during drying of large amount of dilute slurry. • Energy saving is increased using the large amount of hot drying air

Improving Dryer and Press Efficiencies Through Combustion of Hydrocarbon Emissions

Energy Technology Data Exchange (ETDEWEB)

Sujit Banerjee

2005-10-31

Emission control devices on dryers and presses have been legislated into the industry, and are now an integral part of the drying system. These devices consume large quantities of natural gas and electricity and down-sizing or eliminating them will provide major energy savings. The principal strategy taken here focuses on developing process changes that should minimize (and in some cases eliminate) the need for controls. A second approach is to develop lower-cost control options. It has been shown in laboratory and full-scale work that Hazardous Air Pollutants (HAPs) emerge mainly at the end of the press cycle for particleboard, and, by extension, to other prod-ucts. Hence, only the air associated with this point of the cycle need be captured and treated. A model for estimating terpene emissions in the various zones of veneer dryers has been developed. This should allow the emissions to be concentrated in some zones and minimized in others, so that some of the air could be directly released without controls. Low-cost catalysts have been developed for controlling HAPs from dryers and presses. Catalysts conventionally used for regenerative catalytic oxidizers can be used at much lower temperatures for treating press emissions. Fluidized wood ash is an especially inexpensive mate-rial for efficiently reducing formaldehyde in dryer emissions. A heat transfer model for estimating pinene emissions from hot-pressing strand for the manufacture of flakeboard has been constructed from first principles and validated. The model shows that most of the emissions originate from the 1-mm layer of wood adjoining the platen surface. Hence, a simple control option is to surface a softwood mat with a layer of hardwood prior to pressing. Fines release a disproportionate large quantity of HAPs, and it has been shown both theo-retically and in full-scale work that particles smaller than 400 µm are principally responsible. Georgia-Pacific is considering green

24 CFR 3280.708 - Exhaust duct system and provisions for the future installation of a clothes dryer.

Science.gov (United States)

2010-04-01

...(a)(1) through (5). (c) Provisions for future installation of electric clothes dryers. When wiring is... for the future installation of a clothes dryer. 3280.708 Section 3280.708 Housing and Urban... duct system and provisions for the future installation of a clothes dryer. (a) Clothes dryers. (1) All...

Fire propagation through arrays of solid-waste storage drums

International Nuclear Information System (INIS)

Smith, S.T.; Hinkle, A.W.

1995-01-01

The extent of propagation of a fire through drums of solid waste has been an unresolved issue that affects all solid-waste projects and existing solid-waste storage and handling facilities at the Hanford site. The issue involves the question of how many drums of solid waste within a given fire area will be consumed in a design-basis fire for given parameters such as drum loading, storage arrays, initiating events, and facility design. If the assumption that all drums of waste within a given fire area are consumed proves valid, then the construction costs of solid waste facilities may be significantly increased

75 FR 7987 - Energy Conservation Standards for Residential Clothes Dryers and Room Air Conditioners: Public...

Science.gov (United States)

2010-02-23

... Conservation Standards for Residential Clothes Dryers and Room Air Conditioners: Public Meeting and... conservation standards for residential clothes dryers and room air conditioners; the analytical framework..., Mailstop EE-2J, Public Meeting for Residential Clothes Dryers and Room Air Conditioners, EERE-2007-BT-STD...

Listening to the Shape of a Drum

Indian Academy of Sciences (India)

Home; Journals; Resonance – Journal of Science Education; Volume 3; Issue 10. Listening to the Shape of a Drum - You Cannot Hear the Shape of a Drum! S Kesavan. General Article Volume 3 Issue 10 October 1998 pp 49-58. Fulltext. Click here to view fulltext PDF. Permanent link:

Performance Evaluation of an Active Solar Dryer Equipped with an Auxilliary Electrical Heater and Heat Recovery System

International Nuclear Information System (INIS)

Pourghasemi Ranjbar, M.; Alavi Naeini, N.; Mortezapour, H.

2016-01-01

Drying is a very sophisticated process which consumes a large amount of energy. Solar energy can be used as an alternative or supplementary energy source to fossil fuels. Solar dryers are common ways for saving fossil fuel consumption during agricultural products drying. In this study, the performance of an active solar dryer equipped with an energy recovery system was investigated at three levels of drying air temperature. The results showed that the energy recovery system was able to increase inlet air temperature by 16.8, 18.5 and 18.9 ° C at drying temperatures of 55, 65 and 75 ℃, respectively. Meanwhile 47.8, 42.9 and 40.9 percents of the dryer exhaust air energy were recovered respectively at these conditions which subsequently led to a reduction of 30.7, 19.2 and 14.7 percents in electrical heater energy consumption.

Hydrogen explosion testing with a simulated transuranic drum

International Nuclear Information System (INIS)

Dykes, K.L.; Meyer, M.L.

1990-01-01

Transuranic (TRU) waste generated at the Savannah River Site (SRS) is currently stored onsite for future retrieval and permanent disposal at the Waste Isolation Pilot Plant (WIPP). Some of the TRU waste is stored in vented 210-liter (55-gallon) drums and consists of gloves, wipes, plastic valves, tools, etc. Gas generation caused by radiolysis and biodegradation of these organic waste materials may produce a flammable hydrogen-air mixture (>4% v/v) in the multi-layer plastic waste bags. Using a worst case scenario, a drum explosion test program was carried out to determine the hydrogen concentration necessary to cause removal of the drum lid. Test results indicate an explosive mixture up to 15% v/v of hydrogen can be contained in an SRS TRU drum without total integrity failure via lid removal

Performance of a Forced-Convection Greenhouse Dryer for Fish Drying

Directory of Open Access Journals (Sweden)

Martunis Martunis

2013-04-01

Full Text Available ABSTRACT. This research present experimental performance of a forced convection greenhouse dryer for drying of fish. The greenhouse dryer was installed at Aceh province, Indonesia. It has a concrete floor with the area of 6×4 m2. The roof of dryer is built in semi-cylindrical shape and covered with transparent polycarbonate sheets. Two axial flow fans powered by a 50-watt solar cell module was used to generate forced convection for ventilating the dryer.To investigate its performance, the dryer was used to dry two batches of fish. The Results showed that to dry 50 kg fish with initial moisture 68 % required 11 hours. Incontrast, to dry the same amount of fish using sun drying take a time about 2 days. The air temperature inside greenhouse dryer at noon in the clear day was 45-55°C. Kinerja Pengering Rumah Kaca Dengan Metode Konveksi Paksa Untuk Pengeringan Ikan ABSTRAK. Penelitian ini memperlihatkan hasil percobaan terhadap kinerja pengering rumah kaca dengan metode konveksi udara secara paksa pada pengeringan ikan. Penelitian pengering rumah kaca ini dilakukan di Propinsi Aceh, Indonesia. Pengering ini berlantaikan beton dengan luas sebesar 6x4 m2. .Atapnya dibuat berbentuk semi-selinder dan ditutup dengan lembaran plastik transparan berbahan polikarbonat. Dua buah kipas dengan aliran udara secara aksial dipasang dengan sumber daya berasal dari panel surya sebesar 50 Watt dan dipakai untuk menghasilkan konveksi udara paksa pada ventilasi pengering. Untuk menginvestigasi kinerja rumah kaca ini, pengering ini digunakan untuk mengeringkan dua tumpukan ikan. Hasilnya menunjukkan bahwa untuk mengeringkan sebanyak 50 kg ikan dengan kadar air awalnya sebesar 68% membutuhkan waktu selama 11 jam. Sebaliknya, dengan menggunakan sinar matahari secara langsung, untuk mengeringkan ikan dengan jumlah yang sama, maka waktu yang dibutuhkan lebih lama yaitu sekitar 2 hari. Suhu udara di dalam rumah pengering tepat pada siang hari yang cerah berkisar antara 45

Handling 78,000 drums of mixed-waste sludge

International Nuclear Information System (INIS)

Berry, J.B.; Harrington, E.S.; Mattus, A.J.

1991-01-01

The Oak Ridge Gaseous Diffusion Plant (now known as the Oak Ridge K-25 Site) closed two mixed-waste surface impoundments by removing the sludge and contaminated pond-bottom clay and attempting to process it into durable, nonleachable, concrete monoliths. Interim, controlled, above-ground storage included delisting the stabilized sludge from hazardous to nonhazardous and disposing of the delisted monoliths as Class 1 radioactive waste. Because of schedule constraints and process design and control deficiencies, ∼46,000 drums of material in various stages of solidification and ∼32,000 barrels of unprocessed sludge are stored. The abandoned treatment facility still contains ∼16,000 gal of raw sludge. Such storage of mixed waste does not comply with the Resource Conservation and Recovery Act (RCRA) guidelines. This paper describes actions that are under way to bring the storage of ∼78,000 drums of mixed waste into compliance with RCRA. Remediation of this problem by treatment to meet regulatory requirements is the focus of the discussion. 3 refs., 2 figs., 4 tabs

76 FR 971 - Energy Conservation Program for Consumer Products: Test Procedures for Clothes Dryers and Room...

Science.gov (United States)

2011-01-06

.... Detergent Specifications for Clothes Dryer Test Cloth Preconditioning 5. Changes To Reflect Current Usage... conservation standard; (3) updated detergent specifications for clothes dryer test cloth preconditioning; (4... detergent specifications for clothes dryer test cloth preconditioning; (7) update the references to external...

The aesthetic interpretation on Wooden Drum Dancing of Wa people

Directory of Open Access Journals (Sweden)

Youfeng Wang

2017-02-01

Full Text Available The Wa nationality, a typical ethnic group in Yunnan province, is an ancient one lives across Yunnan. The main residences of it are border area beside northern Yunnan and the Wa States in Burma. Among all the Wa dances, Wooden Drum Dancing leads a vital position, and it is also a symbolic dancing in the culture of Wa people. The feature of Wooden Drum Dancing is that every action expending by the beats of wooden drum, namely, first the wooden drum, then the Wooden Drum Dancing. Dancing is an important content in the life of Wa people, and the aesthetics of life comes from dancing, so they present their value on worship by the form of dancing. This article is going to interpret the aesthetic standard on Wa people’s Wooden Drum Dancing by the view of aesthetics, and come into a conclude that the inspiration of such dancing came from practice and their worship to nature and ancestor. The Wooden Drum Dancing displays totally the tough air and solidarity of Wa people, which also presents the fair society of them. The Wooden Drum Dancing is an enriched art that Wa People took from particle life, so dancing of Wa is often classified into the aesthetic area of plain. The information of people’s living situation displayed by Wa dancing also conveys their rich emotions. The sense of beauty within Wooden Drum Dancing will give others a solemn feeling. The formal beauty is displayed by the rhythm of upper part of body, and the power beauty is displayed by the rhythm of the lower part of body.

7 CFR 1434.8 - Containers and drums.

Science.gov (United States)

2010-01-01

... 7 Agriculture 10 2010-01-01 2010-01-01 false Containers and drums. 1434.8 Section 1434.8... REGULATIONS FOR HONEY § 1434.8 Containers and drums. (a)(1) To be eligible for assistance under this part, honey must be packed in: (i) CCC-approved, 5-gallon plastic containers; (ii) 5-gallon metal containers...

Verification calculation of drum and pulley overhead travelling crane on gamma irradiators

International Nuclear Information System (INIS)

Syamsurrijal Ramdja; Ari Satmoko; Sutomo Budihardjo

2010-01-01

Having verified the calculation of dam drum pulleys found on cranes to facilitate the gamma irradiator. Drum is a device for rolling steel ropes while the pulley is a circular pieces called disks, which are made from metal or non-metal to transmit motion and force. Having verified calculation of forces acting style on drums, drum diameter and length and style of press that occurred on drums. Likewise, the pulley, pulley diameter verified calculations, measures of disc and shaft power pulleys. From the verification results will be obtained whether the data drums and pulley device is safe or not safe to use. (author)

Los Alamos waste drum shufflers users manual

International Nuclear Information System (INIS)

Rinard, P.M.; Adams, E.L.; Painter, J.

1993-01-01

This user manual describes the Los Alamos waste drum shufflers. The primary purpose of the instruments is to assay the mass of 235 U (or other fissile materials) in drums of assorted waste. It can perform passive assays for isotopes that spontaneously emit neutrons or active assays using the shuffler technique as described on this manual

JUSTIFICATION FOR A LIMIT OF 15 PERCENT HYDROGEN IN A 55-GALLON DRUM

International Nuclear Information System (INIS)

MARUSICH, R.M.

2007-01-01

The concentration of 15% hydrogen in air in a waste drum is used as the concentration at which the drum remains intact in the case of a deflagration. The following describes what could happen to the drum if 15% hydrogen or more in air were ignited. Table 2 of the Savannah River report WSRC-TR-90-165 ''TRU Drum Hydrogen Explosion Tests'' provides the results of tests performed in 55-gallon drums filled with hydrogen and air mixtures. The hydrogen-air mixtures were ignited by a hot-wire igniter. The results of the tests are shown in Table 1. They concluded that drums can withstand deflagration involving hydrogen concentration up to 15% hydrogen. Testing was performed at Idaho Falls and documented in a letter from RH Beers, Waste Technology Programs Division, EG and G Idaho, to CP Gertz, Radioactive Waste Technology Branch, DOE dated Sept. 29, 1983. In these tests, 55-gallon drums were filled with hydrogen-air mixtures which were ignited. The results in Table 2.2 showed that ignition for drums containing 11% and 14% hydrogen, the drum lid remained on the drum. Ignition in drum with 30% hydrogen resulted in lid loss. It is concluded from the results of these two tests that, for uncorroded drums, a 15% hydrogen in air mixture will not result in loss of drum integrity (i.e., lid remains on, walls remain intact). The drum walls however, may be thinned due to corrosion. The effect of the deflagration on thinner walls is assessed next. Assume a 15% hydrogen in air mixture exists in a drum. The pressure assuming adiabatic isochoric complete combustion (AICC) conditions is 69 psig (using the same deflagration pressure calculation method as in HNF-19492, ''Revised Hydrogen Deflagration Analysis which got 82 psig for 20% hydrogen in air)

A59 Drum Activity database (DRUMAC): system documentation

International Nuclear Information System (INIS)

Keel, Alan.

1993-01-01

This paper sets out the requirements, database design, software module designs and test plans for DRUMAC (the Active handling Building Drum Activity Database) - a computer-based system to record the radiological inventory for LLW/ILW drums dispatched from the Active Handling Building. (author)

PIV measurements of flow structures in a spray dryer

DEFF Research Database (Denmark)

Meyer, Knud Erik; Velte, Clara Marika; Ullum, Thorvald

2011-01-01

Stereoscopic Particle Image Velocimetry (PIV) measurements are made in horizontal planes in a simplified scale model of a spray dryer using water as fluid. The sample rate was sufficient to resolve phenomena at lower frequencies. Data reveal asymmetric velocity fields in both mean fields and dyna......Stereoscopic Particle Image Velocimetry (PIV) measurements are made in horizontal planes in a simplified scale model of a spray dryer using water as fluid. The sample rate was sufficient to resolve phenomena at lower frequencies. Data reveal asymmetric velocity fields in both mean fields...

Development of a revolving drum reactor for open-sorption heat storage processes

International Nuclear Information System (INIS)

Zettl, Bernhard; Englmair, Gerald; Steinmaurer, Gerald

2014-01-01

To evaluate the potential of an open sorption storage process using molecular sieves to provide thermal energy for space heating and hot water, an experimental study of adsorption heat generation in a rotating reactor is presented. Dehydrated zeolite of the type 4A and MSX were used in form of spherical grains and humidified room air was blown through the rotating bed. Zeolite batches of about 50 kg were able to generate an adsorption heat up to 12 kWh and temperature shifts of the process air up to 36 K depending on the inlet air water content and the state of dehydration of the storage materials. A detailed study of the heat transfer effects, the generated adsorption heat, and the evolving temperatures show the applicability of the reactor and storage concept. - Highlights: • Use of an open adsorption concept for domestic heat supply was proved. • A rotating heat drum reactor concept was successfully applied. • Zeolite batches of 50 kg generated up to 12 kWh adsorption heat (580 kJ/kg). • Temperature shift in the rotating material bed was up to 60 K during adsorption

Review on advanced of solar assisted chemical heat pump dryer for agriculture produce

International Nuclear Information System (INIS)

Fadhel, M.I.; Sopian, K.; Daud, W.R.W.; Alghoul, M.A.

2011-01-01

Over the past three decades there has been nearly exponential growth in drying R and D on a global scale. Improving of the drying operation to save energy, improve product quality as well as reduce environmental effect remained as the main objectives of any development of drying system. A solar assisted chemical heat pump dryer is a new solar drying system, which have contributed to better cost-effectiveness and better quality dried products as well as saving energy. A solar collector is adapted to provide thermal energy in a reactor so a chemical reaction can take place. This reduces the dependency of the drying technology on fossil energy for heating. In this paper a review on advanced of solar assisted chemical heat pump dryer is presented (the system model and the results from experimental studies on the system performance are discussed). The review of heat pump dryers and solar assisted heat pump dryer is presented. Description of chemical heat pump types and the overview of chemical heat pump dryer are discussed. The combination of chemical heat pump and solar technology gives extra efficiency in utilizing energy. (author)

Evaluation of X-ray System for Nondestructive Testing on Radioactive Waste Drums

International Nuclear Information System (INIS)

Park, Jong Kil; Maeng, Seong Jun; Lee, Yeon Ee; Hwang, Tae Won

2008-01-01

The physical and chemical properties of radioactive waste drums, which have been temporarily stored on site, should be characterized before their shipment to a disposal facility in order to prove that the properties meet the acceptance guideline. The investigation of NDT(Nondestructive Test) method was figured out that the contents in drum, the quantitative analysis of free standing water and void fraction can be examined with X-ray NDT techniques. This paper describes the characteristics of X-ray NDT such as its principles, the considerations for selection of X-ray system, etc. And then, the waste drum characteristics such as drum type and dimension, contents in drum, etc. were examined, which are necessary to estimate the optimal X-ray energy for NDT of a drum. The estimation results were that: the proper X-ray energy is under 3 MeV to test the drums of 320 β and less; both X-ray systems of 450 keV and/or 3 MeV might be needed considering the economical efficiency and the realization. The number of drums that can be tested with 450 keV and 3 MeV X-ray system was figured out as 42,327 and 18,105 drums (based on storage of 2006. 12), respectively. Four testing scenarios were derived considering equipment procurement method, outsourcing or not, etc. The economical and feasibility assessment for the scenarios was resulted in that an optimal scenario is dependent on the acceptance guide line, the waste generator's policy on the waste treatment and the delivery to a disposal facility, etc. For example, it might be desirable that a waste generator purchases two 450 keV mobile system to examine the drums containing low density waste, and that outsourcing examination for the high density drums, if all NDT items such as quantitative analysis for 'free standing water' and 'void fraction', and confirmation of contents in drum have to be characterized. However, one 450 keV mobile system seems to be required to test only the contents in 13,000 drums per year.

Chimpanzee drumming : a spontaneous performance with characteristics of human musical drumming

NARCIS (Netherlands)

Dufour, Valerie; Poulin, Nicolas; Cure, Charlotte; Sterck, Elisabeth H. M.

2015-01-01

Despite the quintessential role that music plays in human societies by enabling us to release and share emotions with others, traces of its evolutionary origins in other species remain scarce. Drumming like humans whilst producing music is practically unheard of in our most closely related species,

Novel temperature control technique for a medicinal herb dryer system powered by a photovoltaic array

International Nuclear Information System (INIS)

Abd El-Shafy A Nafeh; Hanaa M Fargali; Faten H Fahmy; Mohamed A Hassan

2006-01-01

Each plant has its own optimal drying temperature, especially for the medicinal herbs, because they are sensitive to heat. If the drying temperature becomes more than the optimal value, some chemical reactions will occur and influence the quality of the dried herb, such as color, taste, and aroma. While if the drying temperature becomes lower than the optimal value, the drying process will slow down; and consequently an expected degradation in the quality of the herb may occur, due to insects and fungi infestation which increase in moist conditions. This paper presents a new temperature control technique for a medicinal herb dryer system. The technique fixes the drying temperature of the medicinal herbs at 40 degree C, even in cases of rapidly changing atmospheric conditions. The control of the dryer temperature is achieved through using the proportional integral (PI) controller. The designed dryer contains two systems, which are the thermal and the electrical systems. The thermal system is designed to heat the drying air by using the solar energy and bio-gas fuel. Whereas, the electrical system, which contains a photovoltaic (PV) modules and a battery, is designed to supply the different electrical loads of the dryer system. The control technique is investigated through simulation work by using MATLAB-SIMULINK. The simulation results indicate the high capability of the proposed technique in controlling the drying temperature, even in cases of rapidly changing atmospheric conditions

Conceptual design of pilot scale solar dryer for seaweeds

International Nuclear Information System (INIS)

Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >Roche-Delgado, Liset; Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >Hernández-Touset, Juan Pedro; Marta Abreu de Las Villas (Cuba))" data-affiliation=" (Departamento de Ingeniería Química, Facultad de Química y Farmacia, Universidad Central Marta Abreu de Las Villas (Cuba))" >García-Rodríguez, Agustín

2017-01-01

Drying algal biomass with the use of solar radiation is an economical and environmentally compatible option. The aim of this work was to design an indirect solar dryer with natural air circulation for seaweeds drying. The equipment supports discrete quantities of wet biomass and is protected from environmental situations that may damage the product; it does not need electricity to operate and the construction and operating costs are low. This comprises a collector made of copper plates for air circulation, heated by solar radiation, a glass cover and drying trays with a wooden structure. The dryer was designed to obtain 0, 3 kg / day of dry biomass. The methodology allows construction and operation of a flexible solar dryer in different operating conditions for research on seaweeds. Correspondingly with environmental and operating conditions the design included estimation of drying time, the determination of drying area, number of trays, air flow from the collector to the trays, collector sizing; heat transfer area, temperature reached by air and collector efficiency. (author)

Natural convection solar dryer with biomass back-up heater

Energy Technology Data Exchange (ETDEWEB)

Bena, B.; Fuller, R.J. [University of Melbourne (Australia). Faculty of Engineering

2002-07-01

A direct-type natural convection solar dryer and a simple biomass burner have been combined to demonstrate a drying technology suitable for small-scale processors of dried fruits and vegetables in non-electrified areas of developing countries. From a series of evaluation trials of the system, the capacity of the dryer was found to be 20-22kg of fresh pineapple arranged in a single layer of 0.01-m-thick slices. The overall drying efficiency of the unit was calculated to be {approx} 9%. During the same trial, the drying efficiency of the solar component alone was found to be 22%. Other trials estimated the efficiency of the burner in producing useful heat for drying to be 27%. Key features of the biomass burner were found to be the addition of thermal mass on the upper surface, an internal baffle plate to lengthen the exhaust gas exit path and a variable air inlet valve. Further modifications to further improve the performance of both the solar and biomass components of the dryer are suggested. (author)

Nonlinear vibrations analysis of rotating drum-disk coupling structure

Science.gov (United States)

Chaofeng, Li; Boqing, Miao; Qiansheng, Tang; Chenyang, Xi; Bangchun, Wen

2018-04-01

A dynamic model of a coupled rotating drum-disk system with elastic support is developed in this paper. By considering the effects of centrifugal and Coriolis forces as well as rotation-induced hoop stress, the governing differential equation of the drum-disk is derived by Donnell's shell theory. The nonlinear amplitude-frequency characteristics of coupled structure are studied. The results indicate that the natural characteristics of the coupling structure are sensitive to the supporting stiffness of the disk, and the sensitive range is affected by rotating speeds. The circumferential wave numbers can affect the characteristics of the drum-disk structure. If the circumferential wave number n = 1 , the vibration response of the drum keeps a stable value under an unbalanced load of the disk, there is no coupling effect if n ≠ 1 . Under the excitation, the nonlinear hardening characteristics of the forward traveling wave are more evident than that of the backward traveling wave. Moreover, because of the coupling effect of the drum and the disk, the supporting stiffness of the disk has certain effect on the nonlinear characteristics of the forward and backward traveling waves. In addition, small length-radius and thickness-radius ratios have a significant effect on the nonlinear characteristics of the coupled structure, which means nonlinear shell theory should be adopted to design rotating drum's parameter for its specific structural parameters.

Transverse mixing of ellipsoidal particles in a rotating drum

Directory of Open Access Journals (Sweden)

He Siyuan

2017-01-01

Full Text Available Rotating drums are widely used in industry for mixing, milling, coating and drying processes. In the past decades, mixing of granular materials in rotating drums has been extensively investigated, but most of the studies are based on spherical particles. Particle shape has an influence on the flow behaviour and thus mixing behaviour, though the shape effect has as-yet received limited study. In this work, discrete element method (DEM is employed to study the transverse mixing of ellipsoidal particles in a rotating drum. The effects of aspect ratio and rotating speed on mixing quality and mixing rate are investigated. The results show that mixing index increases exponentially with time for both spheres and ellipsoids. Particles with various aspect ratios are able to reach well-mixed states after sufficient revolutions in the rolling or cascading regime. Ellipsoids show higher mixing rate when rotational speed is set between 25 and 40 rpm. The relationship between mixing rate and aspect ratio of ellipsoids is established, demonstrating that, particles with aspect ratios of 0.5 and 2.0 achieve the highest mixing rates. Increasing rotating speed from 15 rpm to 40 rpm does not necessarily increase the mixing speed of spheres, while monotonous increase is observed for ellipsoids.

Thin layer drying characteristics of curry leaves (Murraya koenigii in an indirect solar dryer

Directory of Open Access Journals (Sweden)

Vijayan Selvaraj

2017-01-01

Full Text Available In this work, the thin layer drying characteristics of curry leaves (Murraya koenigii has been studied in an indirect forced convection solar dryer with constant air mass flow rate of 0.0636 kg/s. Twelve thin layer drying models were tested for its suitability to describe the drying characteristics of curry leaves. The dryer has reduced the initial moisture content of curry leaves from 67.3% (wet basis to the final moisture content of 4.75% (wet basis in 3.5 hours. The pickup efficiency of indirect solar dryer for drying curry leaves was varied between 4.9% and 23.02%. Based on the statistical parameters, the Modified Henderson and Pabis model and Wang and Singh model were selected for predicting the drying characteristics of curry leaves. The payback period for the solar dryer was evaluated as 8 months, which is found to be much lower when compared with the entire life span of 15 years. The payback evaluation confirms that the solar dryer is economically viable in rural applications.

Analysis of heat recovery from a spray dryer by recirculation of exhaust air

International Nuclear Information System (INIS)

Golman, Boris; Julklang, Wittaya

2014-01-01

Highlights: • We study a spray dryer with heat recovery by partial recirculation of exhaust air. • We examine effects of process parameters on energy efficiency and energy savings. • Decreasing drying air temperature and flow rate will increase energy efficiency. • Increasing recirculation ratio and slurry feed rate will increase energy efficiency. - Abstract: Model simulations were employed to investigate the influences of process parameters on the energy recovery in spray drying process that partially recycle the exhaust drying gas. The energy efficiency and energy saving were studied for various values of recirculation ratios with respect to the temperature and flow rate of the drying air, slurry feed rate and concentration of slurry in spray drying of advanced ceramic materials. As a result, significant gains in energy efficiency and energy saving were obtained for a spray drying system with high recirculation ratio of exhaust air. The high slurry feed rate and the low slurry concentration, inlet drying air temperature and drying air flow rate enhanced the energy efficiency of spray drying system. However, the high energy saving was obtained in spray dryers operating at low slurry feed rate and high slurry concentration

A novel rate of the reaction between NaOH with CO2 at low temperature in spray dryer

Directory of Open Access Journals (Sweden)

Yadollah Tavan

2017-03-01

Full Text Available Carbon dioxide (CO2 is an influential greenhouse gas that has a significant impact on global warming partly. Nowadays, many techniques are available to control and remove CO2 in different chemical processes. Since the spray dryer has high removal efficiency rate, a laboratory-scale spray dryer is used to absorb carbon dioxide from air in aqueous solution of NaOH. In the present study, the impact of NaOH concentration, operating temperature and nozzle diameter on removal efficiency of CO2 is explored through experimental study. Moreover, the reaction kinetic of NaOH with CO2 is studied over the temperature range of 50–100 °C in a laboratory-scale spray dryer absorber. In the present contribution, a simple reaction rate equation is proposed that shows the lowest deviation from the experimental data with error less than 2%.

Energetic and economic optimization of solar tunnel dryers with a photovoltaic driven fan

International Nuclear Information System (INIS)

Muehlbauer, W.; Mayer, R.A.; Esper, A.; Reisinger, L.; Linckh, G.; Hensel, O.

1992-02-01

In the recent years the solar tunnel dryer has been used successfully for drying several agricultural products in tropical and subtropical countries. Up to now the dissemination has been limited to electrified areas. Objective of this work has been the improvement of the thermal performance of the tunnel dryer due to a optimization of the plastic film solar air heater as well as optimization work in point of fluid dynamic view to reduce the power requirement of the blower. To improve the efficiency of the blower optimization work had been done by investigating several blower wheels, dc-motors and actuation systems. A PV-System was designed according to these requirements to test the long term behaviour. The remarkable features of the newly designed solar tunnel dryer are the low power requirement for driving the blower and a high efficiency of the actuation. In the range of a power requirement of 80 - 100 W a blower with an efficiency of 48% is now available. The theoretical power requirement of the solar tunnel dryer could be reduced to 11 W. From economic point of view the use of the solar tunnel dryer is possible. (orig.) With 3 refs., 15 tabs., 49 figs [de

Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

Energy Technology Data Exchange (ETDEWEB)

Wayne, David M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2015-10-19

On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO₃), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

Simultaneous Thermal Analysis of WIPP and LANL Waste Drum Samples: A Preliminary Report

International Nuclear Information System (INIS)

Wayne, David M.

2015-01-01

On Friday, February 14, 2014, an incident in P7R7 of the WIPP underground repository released radioactive material into the environment. The direct cause of the event was a breached transuranic (TRU) waste container, subsequently identified as Drum 68660. Photographic and other evidence indicates that the breach of 68660 was caused by an exothermic event. Subsequent investigations (Britt, 2015; Clark and Funk, 2015; Wilson et al., 2015; Clark, 2015) indicate that the combination of nitrate salts, pH neutralizing chemicals, and organic-based adsorbent represented a potentially energetic mixture. The materials inside the breached steel drum consisted of remediated, 30- to 40-year old, Pu processing wastes from LANL. The contents were processed and repackaged in 2014. Processing activities at LANL included: 1) neutralization of acidic liquid contents, 2) sorption of the neutralized liquid, and 3) mixing of acidic nitrate salts with an absorber to meet waste acceptance criteria. The contents of 68660 and its sibling, 68685, were derived from the same parent drum, S855793. Drum S855793 originally contained ten plastic bags of acidic nitrate salts, and four bags of mixed nitrate and oxalate salts generated in 1985 by Pu recovery operations. These salts were predominantly oxalic acid, hydrated nitrate salts of Mg, Ca, and Fe, anhydrous Na(NO 3 ), and minor amounts of anhydrous and hydrous nitrate salts of Pb, Al, K, Cr, and Ni. Other major components include sorbed water, nitric acid, dissolved nitrates, an absorbent (Swheat Scoop®) and a neutralizer (KolorSafe®). The contents of 68660 are described in greater detail in Appendix E of Wilson et al. (2015)

Critical Point Dryer: Tousimis 916B Series C

Data.gov (United States)

Federal Laboratory Consortium — Description:CORAL Name: Critical Point DryerThis system utilizes CO 2to dry fragile suspended and floating structures Specifications / Capabilities:Wafer size up to...

RATIONALE FOR CENTERING CAPACITY OF REDISIGNED BELT CONVEYOR DRUMS

Directory of Open Access Journals (Sweden)

V. V. Suglobov

2016-02-01

Full Text Available Purpose. In the study is necessary: 1 to justify aligning drums of a new design of belt conveyors; 2 to develop a method for calculating and determining the rational design parameters of drums depending on the technical parameters of the conveyor belt (the length of the conveyor, belt width, the performance of the conveyor, the diameter of the drive and tension drums, etc.; 3 to carry out pilot studies of efficiency conveyor belt in a production environment in order to determine the magnitude of dynamic loads and a comparative evaluation of the effectiveness of the centering ability of conventional and new designs of drums. Methodology. To substantiate the effectiveness of the centering ability of the drums of a new design by the authors developed a mathematical model of interaction of the tape with the drum. Mathematical simulation of tape reels with new design comes to drawing up a differential equation of the belt based on the dynamic component and restoring force. This model allowed us to estimate the movement of the tape in the transverse direction based on the calculated additional dynamic loads and forces on the investigated centering a conveyor belt with given specifications. For the first time the technique of calculating and determining the rational parameters of the drums, which allows determining the design parameters of the centering portions, depending on the mechanical properties and geometric parameters of the tape. Findings. With the help of mathematical modeling the scientifically substantiated effect of centering the ability of the new design of the drum, which ensures stable tape running along the longitudinal axis of the conveyor. The authors made the following conclusions: 1 the mathematical model of interaction with the new belt design of the drum, which allowed to describe the belt in the transverse direction in view of additional dynamic loads and renewable power was developed; 2 the method of calculation and

Measurement of dose rate and estimation of beta activity in zircaloy hull drum

International Nuclear Information System (INIS)

Pandey, J.P.N.; Kumar, Pankaj; Shinde, A.M.; Purohit, R.G.; Sarkar, P.K.

2012-01-01

Fuel Reprocessing Plant is designed for the processing of spent fuel from reactor for the recovery of plutonium and uranium as PuO 2 and U 3 O 8 respectively. Zircaloy is used as cladding material of natural uranium fuel pins used in the reactors. In reprocessing plants chop and leach method is used to remove the zircaloy clad from the fuel matrix during Head End Treatment. Initially spent fuel bundles are chopped into pieces and collected in perforated baskets kept in dissolvers. All chopped pieces are dissolved in HNO 3 in the dissolvers followed by heating and boiling. Dissolved solutions are transferred to Filtrate Tank (FT) leaving behind un-dissolved zircoloy hull pieces in the dissolver baskets. Un-dissolved and almost dry hull pieces are transferred in hull drum from the dissolver baskets using the Hull Tilting Facility. Hull drums are made of stainless steel having 500 litre capacity and two third of its volume is filled with zircoloy pieces. Hull drums filled with hull pieces are loaded in Hull Removal Cask (HRC) and transported to SWMF (Solid Waste Management Facility) site for interim storage/disposal in tile holes. Hull pieces are high active solid wastes which contain significant amount of fission products. Radiation levels on hull drums are in the range of few hundreds of mGy/h which has high potential of external hazards if not handled properly. Therefore hull drums are handled remotely in specially designed lead shielded cask

Experimental investigation of a solar dryer with natural convective heat flow

Energy Technology Data Exchange (ETDEWEB)

Gbaha, P.; Yobouet Andoh, H.; Kouassi Saraka, J. [Laboratoire d' Energies d' Energies Nouvelles et Renouvelables, Institut National Polytechnique Felix Houphoeuet-Boigny, B.P. 1526 Yamoussoukro (Ivory Coast); Kamenan Koua, B.; Toure, S. [Laboratoire d' Energie Solaire, Universite de Cocody, 22 B.P.: 582, Abidjan 22 (Ivory Coast)

2007-09-15

A direct type natural convection solar dryer is designed. It is constructed in local materials (wood, blades of glass, metals) then tested experimentally in foodstuffs drying (cassava, bananas, mango). It is about an experimental approach which consists in analyzing the behavior of the dryer. The study relates mainly kinetics and establishment of drying heat balances. The influence of significant parameters governing heat and mass transfers, such as solar incident radiation, drying air mass flow and effectiveness, is analyzed in order to evaluate its thermal performances. Experimental data can be represented by empirical correlations of the form M(t)=M{sub i}exp(-kt) for representation of drying process. The resolution of these drying equations makes-possible to predict total drying time of each product. Moreover, this drying process allows to reduce the moisture content of cassava and sweet banana approximately to 80% in 19 and 22 h, respectively to reach the safety threshold value of 13%. This value permits the conservation of these products about one year without deterioration. The determination of parameters, like ambient temperature, drying chamber temperature, drying air mass flow and incident heat fluxes, allow to predict the drying effectiveness for modeling and refining the dimensioning of the elaborate prototype. (author)

Experimental investigation of rotating-drum separators for liquid-metal MHD applications

International Nuclear Information System (INIS)

Lenzo, C.S.; Dauzvardis, P.V.; Hantman, R.G.

1978-01-01

For the past several years, Argonne National Laboratory has been active in the development of closed-cycle two-phase-flow MHD power systems. One of the key components in such systems is an effective and efficient gas-liquid separator-diffuser. On the basis of an assessment of present technology, it was decided to study the characteristics of a rotating drum type of separator, and a multitask research and development program was initiated within the overall liquid-metal MHD research program. The first task, now completed, centered on the investigation of single-phase flow (liquid) deposited by a flow nozzle on the inner surface of freely-rotating cylinders or drums of 423 mm and 282 mm diam. The tests were designed to study the recovery of energy in the liquid layer deposited on the drum; the torque transmitted to the drum by the liquid as the result of shear stress between the liquid and the drum surface; the characteristics of the liquid layer; and the effects of drum size, nozzle shape and orientation, and nozzle velocity. The test results showed that a stable liquid film was formed on the drum and that the kinetic energy of the liquid layer was high enough to be potentially useful in two-phase-flow MHD power systems

Fire testing of 55 gallon metal waste drums for dry waste storage

International Nuclear Information System (INIS)

Hasegawa, H.K.; Staggs, K.J.; Doughty, S.M.

1993-07-01

The primary goal of this test program was to conduct a series of fire test to provide information on the fire performance of 55 gallon metal waste drums used for solid waste disposal at Department Of Energy (DOE) facilities. This program was limited in focus to three different types of 55 gallon drums, one radiant heat source, and one specific fire size. The initial test was a single empty 55 gallon drum exposed to a standard ASTME-119 time temperature curve for over 10 minutes. The full scale tests involved metal drums exposed to a 6' diameter flammable liquid fire for a prescribed period of time. The drums contained simulated dry waste materials of primarily class A combustibles. The test results showed that a conventional 55 gallon drum with a 1in. bung would blow its lid consistently

Evaluating the parameters of a mobile maize dryer in practice

Directory of Open Access Journals (Sweden)

Josef Los

2013-01-01

Full Text Available The method of drying maize for grain has been recently employed on a large scale in the Czech Republic not only thanks to new maize hybrids but also thanks to the existence of new models of drying plants. One of the new post-harvest lines is a plant in Lipoltice (mobile dryer installed in 2010, storage base in 2012 where basic operational measurements were made of the energy intensiveness of drying and operating parameters of the maize dryer were evaluated. The process of maize drying had two stages, i.e. pre-drying from the initial average grain humidity of 28.55% to 19.6% in the first stage, and the additional drying from 16.7% to a final storage grain humidity of 13.7%. Mean volumes of natural gas consumed per 1 t% for drying in the first and second stage amounted to 1.275 m3 and 1.56 m3, respectively. The total mean consumption of electric energy per 1 t% was calculated to be 1.372 kWh for the given configuration of the post-harvest line.

Study on mechanics of driving drum with superelastic convexity surface covering-layer structure

Energy Technology Data Exchange (ETDEWEB)

Xiao, L.J.; Sui, X.H.; Miao, D.J. [Shandong University of Science & Technology, Qingdao (China)

2008-09-15

Belt conveyor is one of the main transport equipment in coal mine and the driving drum is its key part. With the method of bionic design, the mushroom morphological structure is applied to the design of covering-layer structure of driving drum surface of belt conveyor. Superelastic rubber with large deformation is adopted as the covering-layer material. Nonlinear constitutive model of rubber, which is of superelasticity and large deformation, is established. The stress states and deformation principles of driving drums including both bionic covering-layer and common covering-layer are obtained by static intensity analysis with Finite Element Analysis (FEA) software ANSYS. The values of the stress and strain on the driving drum surface are gotten and the dangerous area is determined. FEA results show that the superelastic convexity surface structure can enlarge the contact area between the driving drum and viscoelastic belt. The results also show that in comparison with common driving drum, the bionic surface driving drum can not only increase the friction coefficient between drum and belt but also prolong its service life.

Expected precision of neutron multiplicity measurements of waste drums

International Nuclear Information System (INIS)

Ensslin, N.; Krick, M.S.; Menlove, H.O.

1995-01-01

DOE facilities are beginning to apply passive neutron multiplicity counting techniques to the assay of plutonium scrap and residues. There is also considerable interest in applying this new measurement technique to 208-liter waste drums. The additional information available from multiplicity counting could flag the presence of shielding materials or improve assay accuracy by correcting for matrix effects such as (α,n) induced fission or detector efficiency variations. The potential for multiplicity analysis of waste drums, and the importance of better detector design, can be estimated by calculating the expected assay precision using a Figure of Merit code for assay variance. This paper reports results obtained as a function of waste drum content and detector characteristics. We find that multiplicity analysis of waste drums is feasible if a high-efficiency neutron counter is used. However, results are significantly poorer if the multiplicity analysis must be used to solve for detection efficiency

Re-evaluation of the 1995 Hanford Large Scale Drum Fire Test Results

International Nuclear Information System (INIS)

Yang, J M

2007-01-01

A large-scale drum performance test was conducted at the Hanford Site in June 1995, in which over one hundred (100) 55-gal drums in each of two storage configurations were subjected to severe fuel pool fires. The two storage configurations in the test were pallet storage and rack storage. The description and results of the large-scale drum test at the Hanford Site were reported in WHC-SD-WM-TRP-246, ''Solid Waste Drum Array Fire Performance,'' Rev. 0, 1995. This was one of the main references used to develop the analytical methodology to predict drum failures in WHC-SD-SQA-ANAL-501, 'Fire Protection Guide for Waste Drum Storage Array,'' September 1996. Three drum failure modes were observed from the test reported in WHC-SD-WM-TRP-246. They consisted of seal failure, lid warping, and catastrophic lid ejection. There was no discernible failure criterion that distinguished one failure mode from another. Hence, all three failure modes were treated equally for the purpose of determining the number of failed drums. General observations from the results of the test are as follows: (lg b ullet) Trash expulsion was negligible. (lg b ullet) Flame impingement was identified as the main cause for failure. (lg b ullet) The range of drum temperatures at failure was 600 C to 800 C. This is above the yield strength temperature for steel, approximately 540 C (1,000 F). (lg b ullet) The critical heat flux required for failure is above 45 kW/m 2 . (lg b ullet) Fire propagation from one drum to the next was not observed. The statistical evaluation of the test results using, for example, the student's t-distribution, will demonstrate that the failure criteria for TRU waste drums currently employed at nuclear facilities are very conservative relative to the large-scale test results. Hence, the safety analysis utilizing the general criteria described in the five bullets above will lead to a technically robust and defensible product that bounds the potential consequences from postulated

Steam generator with integral downdraft dryer

Energy Technology Data Exchange (ETDEWEB)

Hochmuth, F.W.

1992-02-01

On June 30, 1989, a financial assistance award was granted by the United State Department of Energy, the purpose of which was to study and evaluate the technical aspect, the economic viability, and commercial possibilities of a new furnace design for burning high moisture cellulose type fuels. The new design is an invention by F.W. Hochmuth, P.Eng. and has received United States Patents Nos. 4,480, 557 and 4,502,397. It was conceived as a method to improve the general operation and efficiency of waste wood burning boilers, to avoid the use of stabilizing fuels such as oil or gas, and to reduce objectionable stack emissions. A further objective was to obtain such benefits at relatively low cost by integrating all new material requirements within the furnace itself thereby avoiding the need for costly external equipment. The proposed integral down-draft dryer avoids the use of external dryer systems that are very expensive, have high power consumption, and require a large amount of maintenance. This document provides the details of this invention.

Remote radioactive waste drum inspection with an autonomous mobile robot

International Nuclear Information System (INIS)

Heckendorn, F.M.; Ward, C.R.; Wagner, D.G.

1992-01-01

An autonomous mobile robot is being developed to perform remote surveillance and inspection task on large numbers of stored radioactive waste drums. The robot will be self guided through narrow storage aisles and record the visual image of each viewable drum for subsequent off line analysis and archiving. The system will remove the personnel from potential exposure to radiation, perform the require inspections, and improve the ability to assess the long term trends in drum conditions

Application of artificial neural networks on the characterization of radioactive waste drums

International Nuclear Information System (INIS)

Potiens Junior, Ademar Jose; Hiromoto, Goro

2011-01-01

The methodology consist of system simulation of drum-detector by Monte Carlo for obtention of counting efficiency. The obtained data were treated and a neural artificial network (RNA) were constructed for evaluation of total activity of drum. For method evaluation measurements were performed in ten position parallel to the drum axis and the results submitted to the RNA. The developed methodology showed to be effective for isotopic characterization of gamma emitter radioactive wastes distributed in a heterogeneous way in a 200 litters drum. The objective of this work as to develop a methodology of analyse for quantification and localization of radionuclides not homogeneous distributed in a 200 liters drum based on the mathematical techniques

Fatigue life estimation on coke drum due to cycle optimization

Science.gov (United States)

Siahaan, Andrey Stephan; Ambarita, Himsar; Kawai, Hideki; Daimaruya, Masashi

2018-04-01

In the last decade, due to the increasing demand of petroleum product, the necessity for converting the heavy oil are increasing. Thus, demand for installing coke drum in whole world will be increase. The coke drum undergoes the cyclic high temperature and suddenly cooling but in fact is not designed to withstand that kind of cycle, thus the operational life of coke drum is much shorter in comparison to other equipment in oil refinery. Various factors determine in order to improve reliability and minimize the down time, and it is found that the cycle optimization due to cycle, temperature, and pressure have an important role. From this research it is found that the fatigue life of the short cycle is decrease by a half compare to the normal cycle. It also found that in the preheating stage, the stress peak is far exceed the yield strength of coke drum material and fall into plastic deformation. This is happened because of the temperature leap in the preheating stage that cause thermal shock in the upper part of the skirt of the coke drum.

Development of simulation code for FBR spent fuel dissolution with rotary drum type continuous dissolver

International Nuclear Information System (INIS)

Sano, Yuichi; Katsurai, Kiyomichi; Washiya, Tadahiro; Koizumi, Tsutomu; Matsumoto, Satoshi

2011-01-01

Japan Atomic Energy Agency (JAEA) has been studying rotary drum type continuous dissolver for FBR spent fuel dissolution. For estimating the fuel dissolution behavior under several operational conditions in this dissolver, we have been developing the simulation code, PLUM, which mainly consists of 3 modules for calculating chemical reaction, mass transfer and thermal balance in the rotary drum type continuous dissolver. Under the various conditions where dissolution experiments were carried out with the batch-wise dissolver for FBR spent fuel and with the rotary drum type continuous dissolver for UO 2 fuel, it was confirmed that the fuel dissolution behaviors calculated by the PLUM code showed good agreement with the experimental ones. Based on this result, the condition for obtaining the dissolver solution with high HM (heavy metal : U and Pu) concentration (∼500g/L), which is required for the next step, i.e. crystallization process, was also analyzed by this code and appropriate operational conditions with the rotary drum type continuous dissolver, such as feedrate, concentration and temperature of nitric acid, could be clarified. (author)

Development of heat pump and infrared-convective dryer and performance analysis for stale bread drying

International Nuclear Information System (INIS)

Aktaş, Mustafa; Şevik, Seyfi; Aktekeli, Burak

2016-01-01

Highlights: • Investigation of stale bread drying behaviors by developing the HPD and IRD. • New techniques for the HP and IR dryers are proposed and found to be efficient. • Evaluations on potential uses low temperature applications of the dryers were reported. • 35.6% of energy saving was provided by heat recovery device. • The overall system efficiency of HPD was calculated as 13–60%. - Abstract: This experimental study aims to develop a heat pump dryer (HPD) and an infrared dryer (IRD) also the comparative empirical analyses of these two methods and to analyze the drying kinetic of stale bread sliced 15 mm thickness and effectiveness on the drying kinetics of the stale bread of dryers. Dryers have been developed by using different techniques such as heat recovery unit, proportional control (PC) of drying air temperature, simultaneous control of the relative humidity–temperature–air flow rate, water cycle dehumidifier and closed-loop cycle to increase the drying efficiency of industrial drying applications. The highest coefficient of performance of the whole heat pump system (COP_w_s_,_H_P) was calculated as 3.7 and drying efficiencies of the IRD and HPD systems were calculated as 39% and 25%, respectively. When the HPD and IRD systems were compared in terms of drying time and energy consumption, it was observed that the IRD system did not only shortened the drying time up to 69%, but also decreased the energy consumption of the system by 43.2%. Based on the obtained results the effective moisture diffusivity (D_e) was calculated in the range from 8.3 × 10"−"8 to 3.2 × 10"−"7 m"2/s and mass transfer coefficient (h_m) was varied from 1.17 × 10"−"5 to 4.52 × 10"−"5 m/s. It was concluded that both dryers have significant effect in reduction of water content; the relative humidity controlled HPD can be applied efficiently for dryers and the dried stale bread can be reused as bread crumb by food industry.

Slurry spray distribution within a simulated laboratory scale spray dryer

International Nuclear Information System (INIS)

Bertone, P.C.

1979-01-01

It was found that the distribution of liquid striking the sides of a simulated room temperature spray dryer was not significantly altered by the choice of nozles, nor by a variation in nozzle operating conditions. Instead, it was found to be a function of the spray dryer's configuration. A cocurrent flow of air down the drying cylinder, not possible with PNL's closed top, favorably altered the spray distribution by both decreasing the amount of liquid striking the interior of the cylinder from 72 to 26% of the feed supplied, and by shifting the zone of maximum impact from 1.0 to 1.7 feet from the nozzle. These findings led to the redesign of the laboratory scale spray dryer to be tested at the Savannah River Plant. The diameter of the drying chamber was increased from 5 to 8 inches, and a cocurrent flow of air was established with a closed recycle. Finally, this investigation suggested a drying scheme which offers all the advantages of spray drying without many of its limitations

Experimental study of liquid carryover in a separator drum

International Nuclear Information System (INIS)

Prabhudharwadkar, Deoras M.; More, Rahul Z.; Iyer, Kannan N.

2010-01-01

The phenomenon of carryover, i.e. entrainment of liquid along with separated steam is observed in all the steam separators. Due to the risks, such as turbine blade erosion and radioactivity leakage, associated with it, it is desired to have an estimate of the carryover value. This is all the more important when the separation is only under the influence of gravity as proposed in some of the new generation natural circulation reactors. Experiments were carried out in an air-water facility at atmospheric conditions to characterize the entrainment in drums with ratio of the drum diameter to riser diameter varying from 1 to 6. Various parameters influencing the liquid entrainment were identified. The vapour superficial velocity and the drum diameter to riser diameter ratio were found to be the most influencing parameters. A dimensionless prediction correlation was evolved for the liquid entrainment and it was found to agree with previous works in the literature for drum to riser diameter ratio equal to 1.

49 CFR 178.509 - Standards for plastic drums and jerricans.

Science.gov (United States)

2010-10-01

... than production residues or regrind from the same manufacturing process may be used unless approved by... those used in the manufacture of the design type, retesting may be omitted if the carbon black content... or heads of drums and jerricans must be so designed and applied that they remain secure and leakproof...

Drying process optimization for an API solvate using heat transfer model of an agitated filter dryer.

Science.gov (United States)

Nere, Nandkishor K; Allen, Kimberley C; Marek, James C; Bordawekar, Shailendra V

2012-10-01

Drying an early stage active pharmaceutical ingredient candidate required excessively long cycle times in a pilot plant agitated filter dryer. The key to faster drying is to ensure sufficient heat transfer and minimize mass transfer limitations. Designing the right mixing protocol is of utmost importance to achieve efficient heat transfer. To this order, a composite model was developed for the removal of bound solvent that incorporates models for heat transfer and desolvation kinetics. The proposed heat transfer model differs from previously reported models in two respects: it accounts for the effects of a gas gap between the vessel wall and solids on the overall heat transfer coefficient, and headspace pressure on the mean free path length of the inert gas and thereby on the heat transfer between the vessel wall and the first layer of solids. A computational methodology was developed incorporating the effects of mixing and headspace pressure to simulate the drying profile using a modified model framework within the Dynochem software. A dryer operational protocol was designed based on the desolvation kinetics, thermal stability studies of wet and dry cake, and the understanding gained through model simulations, resulting in a multifold reduction in drying time. Copyright © 2012 Wiley-Liss, Inc.

Corrosion susceptibility of steel drums containing cemented intermediate level nuclear wastes

Science.gov (United States)

Duffó, Gustavo S.; Farina, Silvia B.; Schulz, Fátima M.; Marotta, Francesca

2010-10-01

Cementation processes are used as immobilization techniques for low or intermediate level radioactive waste for economical and safety reasons and for being a simple operation. In particular, ion-exchange resins commonly used for purification of radioactive liquid waste from nuclear reactors are immobilized before being stored to improve the leach resistance of the waste matrix and to maintain mechanical stability. Combustible solid radioactive waste can be incinerated and the resulting ashes can also be immobilized before storage. The immobilized resins and ashes are then contained in steel drums that may undergo corrosion depending on the presence of certain contaminants. The work described in this paper was aimed at evaluating the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins and incineration ashes containing different concentrations of aggressive species (mostly chloride and sulphate ions). A special type of specimen was designed to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 1 year. The results show the deleterious effect of chloride on the expected lifespan of the waste containers.

Corrosion susceptibility of steel drums containing cemented intermediate level nuclear wastes

International Nuclear Information System (INIS)

Duffo, Gustavo S.; Farina, Silvia B.; Schulz, Fatima M.; Marotta, Francesca

2010-01-01

Cementation processes are used as immobilization techniques for low or intermediate level radioactive waste for economical and safety reasons and for being a simple operation. In particular, ion-exchange resins commonly used for purification of radioactive liquid waste from nuclear reactors are immobilized before being stored to improve the leach resistance of the waste matrix and to maintain mechanical stability. Combustible solid radioactive waste can be incinerated and the resulting ashes can also be immobilized before storage. The immobilized resins and ashes are then contained in steel drums that may undergo corrosion depending on the presence of certain contaminants. The work described in this paper was aimed at evaluating the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins and incineration ashes containing different concentrations of aggressive species (mostly chloride and sulphate ions). A special type of specimen was designed to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix were monitored over a time period of 1 year. The results show the deleterious effect of chloride on the expected lifespan of the waste containers.

Radwaste disposal drum centrifuge

International Nuclear Information System (INIS)

Rubin, L.S.; Deltete, C.P.; Crook, M.R.

1988-01-01

The drum or processing bowl of the DDC becomes the disposal container when the filling operation is completed. Rehandling of the processed resin is eliminated. By allowing the centrifugally compacted resin to remain in the processing container, extremely efficient waste packaging can be achieved. The dewatering results and volume reductions reported during 1986 were based upon laboratory scale testing sponsored by the Electric Power Research Institute (EPRI) and the Department of Energy (DOE). Since the publication of these preliminary results, additional testing using a full-scale prototype DDC has been completed, again under the auspices of the DOE. Full-scale testing has substantiated the results of earlier testing and has formed the basis for preliminary discussions with the U.S. Nuclear Regulatory Commission (NRC) regarding DDC licensing for radioactive applications. A comprehensive Topical Report and Process Control Program is currently being prepared for submittal to the NRC for review under a utility licensing action. Detailed cost-benefit analyses for actual plant operations have been prepared to substantiate the attractiveness of the DDC. Several methods to physically integrate a DDC into a nuclear power plant have also been developed

FIPS: a process for the solidification of fission product solutions using a drum drier. [HTGR fuel reprocessing

Energy Technology Data Exchange (ETDEWEB)

Halaszovich, St.; Laser, M.; Merz, E.; Thiele, D.

1976-08-01

A new process consisting of the steps concentration of the fission product solution, denitration of the solution by addition of formaldehyde, addition of glass-forming additives, drying of the slurry using a drum drier, melting of the dry product in the crucible by rising level in-pot-melting, and off-gas treatment and recovery of nitric acid is under development. A small plant with a capacity of 1 kg glass per hour has been tested in hot cells with fission product solutions from LWR fuel element reprocessing since December 1974. The equipment is very simple to operate and to control. No serious problems arose during operation.

Material Selection for a Manual Winch Rope Drum

OpenAIRE

Moses F. Oduori; Enoch K. Musyoka; Thomas O. Mbuya

2016-01-01

The selection of materials is an essential task in mechanical design processes. This paper sets out to demonstrate the application of analytical decision making during mechanical design and, particularly, in selecting a suitable material for a given application. Equations for the mechanical design of a manual winch rope drum are used to derive quantitative material performance indicators, which are then used in a multiple attribute decision making (MADM) model to rank the candidate materials....

Drying of Rhinacanthus nasutus (Linn. Kurz. using a solar dryer incorporated with a backup thermal energy storage from wood combustion

Directory of Open Access Journals (Sweden)

Perapong Tekasakul

2006-05-01

Full Text Available An indirect, natural convection, solar cabinet dryer incorporated with a backup thermal energy storage from wood combustion was designed and tested with the Thai herb, Rhinacanthus nasutus (Linn. Kurz. Most of Thai herbs are widely used as traditional medicine and drying is an initial step in the production process. Solar dryer with a biomass backup heating system is the most feasible solution to drying in Thailand. In this work, a 4 m x 5 m solar collector was used to absorb solar radiation for heating the incoming air during the daytime, while a biomass burner was used to supply heat when solar energy was not possible. Heat from fuelwood combustion was accumulated in the thermal storage system made of bricks, and was used to heat up the incoming air. Results showed that the herb was dried uniformly and the temperature inside the drying cabinet could be maintained above 50ºC for more than 10 hours. Thermal efficiency when using solar energy was 10.5%, but the value was less than 1% when using the heat from biomass burning. This resulted from the low moisture content of the products after being dried by the solar energy. The dryer is beneficial to the operators, particularly in southern Thailand, where continuous drying is required. This dryer is by no means limited to drying of the herb. Currently, four dryers of the same model have been used by farmer groups in southern Thailand for drying bananas, several types of herbs, fish, and other products. In economic consideration, its payback period is 5.5 years when compared with the LPG-equipped dryer. When the total cost and production capacity are considered, its payback period is about 6 years.

Drying of Rosella (Hibiscus sabdariffa Flower Petals using Solar Dryer with Double Glass Cover Collector

Directory of Open Access Journals (Sweden)

Tjukup Marnoto

2014-10-01

Full Text Available Chemical ingredients in rosella petals are very beneficial for health. Rosella petals needed to be drained for storage and packing purpose. The traditional drying takes 5 days and less healthy. Solar dryer technology can speed up the drying process and protect materials from dust contamination. Solar dryer with double glass covered collector has been designed and made for drying of agricultural products such as rosella flowers. Rosella petals as much as 2300 grams with initial moisture content of 90.84 % be dried with this dryer until the moisture content of 7.67 % takes only 2 days, although the weather was less sunny . The temperature in the drying chamber was not more than 50° C, so it was good for drying groceries, not damaging chemical ingredients. The relative humidity in the space dryeris was about 40 % and it was still relative low. Drying rate and drying performance was expressed by the efficiency and Specific Moisture Evaporation Rate ( SMER were influenced by water content of the dried material and weather. Daily efficiency at the first and the second day: 14.931 % and 5.78%, while the daily SMER on the first and the second day: 0.222 and 0.0256 ( kg / kWh .

Corrosion of steel drums containing cemented ion-exchange resins as intermediate level nuclear waste

Science.gov (United States)

Duffó, G. S.; Farina, S. B.; Schulz, F. M.

2013-07-01

Exhausted ion-exchange resins used in nuclear reactors are immobilized by cementation before being stored. They are contained in steel drums that may undergo internal corrosion depending on the presence of certain contaminants. The objective of this work is to evaluate the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins with different aggressive species. The corrosion potential and the corrosion rate of the steel, and the electrical resistivity of the matrix were monitored for 900 days. Results show that the cementation of ion-exchange resins seems not to pose special risks regarding the corrosion of the steel drums. The corrosion rate of the steel in contact with cemented ion-exchange resins in the absence of contaminants or in the presence of 2.3 wt.% sulphate content remains low (less than 0.1 μm/year) during the whole period of the study (900 days). The presence of chloride ions increases the corrosion rate of the steel at the beginning of the exposure but, after 1 year, the corrosion rate drops abruptly reaching a value close to 0.1 μm/year. This is probably due to the lack of water to sustain the corrosion process. When applying the results obtained in the present work to estimate the corrosion depth of the steel drums containing the cemented radioactive waste after a period of 300 years, it is found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums. Cementation of ion-exchange resins does not seem to pose special risks regarding the corrosion of the steel drums that contained them; even in the case the matrix is highly contaminated with chloride ions.

Performance of a chevron steam dryer for removal of lead-bismuth droplets

International Nuclear Information System (INIS)

Dostal, Vaclav; Yusibani, Elin; Takahashi, Minoru

2005-01-01

An analysis was performed of a chevron type steam dryer with a trap for the removal of lead-bismuth droplets from steam leaving the Water Boiling Direct Contact Lead or Lead-Bismuth Cooled Reactor. The Lagrangian method was used and is described here. The steam flow field was developed using a CFD code FrontFlow/Red. The simulated dryer performance results were compared to a simple theoretical model from literature. The simulation shown that droplets down to 6 microns in diameter can be completely removed by the steam dryer, which is better than reported earlier in literature. A discrepancy with the theoretical model was found for larger droplets (5 to 10 microns in diameter), where the theoretical model predicted lower removal efficiency. The discrepancy is attributed to be installation of the trap, which is not included in this theoretical model. Some droplets of 1 and 0.5 microns were removed in the dryer as well, which indicates the potential for the fine droplet removal if the trap design is carefully optimized. The investigation of the effect of initial droplet velocity shown that the removal efficiency increases with the increase of the positive velocity components. For larger droplets the effect of initial velocity was found to be minuscule. (author)

Model air-supported drum-type homopolar generator

International Nuclear Information System (INIS)

Kustom, R.L.; Fuja, R.E.; Wehrle, R.B.; Smith, R.P.; Kovarik, T.J.

1977-01-01

A single cylinder, drum-type homopolar generator has been designed and built for the purpose of developing a simple air support system for thin cylinder rotors operated at high surface velocities and significant radial drum growth. The model has an aluminum cylinder which is 0.32 cm thick, 25 cm in diameter, and 12.7 cm long. It is designed to operate at a peak current of 2500 A and to store a total of 40 kJ with a surface velocity of 305 m/sec

Performance studies of solar tunnel dryer for drying aonla (Embilica Officinalis) pulp

International Nuclear Information System (INIS)

Seveda, M. S.

2012-01-01

A solar tunnel dryer was constructed and evaluated the performance for drying aonla pulp. The dryer consists of a transparent UV stabilized plastic covered solar collector cum drying unit. Evaluation parameters are air temperature, solar insolation, moisture content, relative humidity and airflow rate. A minimum of 111.18 m 2 solar collector area is required to dry a batch 1000 kg aonla pulp in 16 hours (two days drying period). The initial and final moisture content considered were 424.93 and 10.08% dry basis, respectively. It was observed that on an average 43 per cent of higher temperature was obtained in solar tunnel dryer over the ambient temperature. The results obtained during the test period denoted that the maximum gained energy occurred at 13 o'clock hour and then gradually declined since the maximum solar radiation occurred at this time. (author)

Tritium isotopic exchange in air detritiation dryers

International Nuclear Information System (INIS)

Everatt, A.E.; Johnson, R.E.; Senohrabek, J.A.; Shultz, C.M.

1989-02-01

Isotopic exchange between tritiated and non-tritiated water species in a molecular sieve bed has been demonstrated. At high humidities (+6 degrees Celsius dew point) the rate of tritium isotopic exchange in a 2.4 L molecular sieve bed has been demonstrated to be at least 50% of published exchange rates. In an industrial-sized air detritiation dryer, utilizing the pretreatment technique of H 2 O steam washing to elute the residual tritium, a DF of 12 600 has been demonstrated when operating at an inlet vapor tritium concentration of 14 Ci/kg and at inlet and outlet dew points of 4.8 and -54 degrees Celsius, respectively. In the NPD dryer bed studied, which was not optimally designed for full benefit from isotopic exchange, at least one order of magnitude in additional detritiation is attributed to isotopic exchange in the unsaturated zone. The technique of eluting the residual tritium from an industrial sized bed by H 2 O washing at high temperature, high humidity and low bed loading has been demonstrated to be a fast and effective way of removing tritium from a molecular sieve bed during regeneration. The isotopic exchange model accurately predicted the exchange between tritiated and non-tritiated water species in a molecular sieve bed where there is no net adsorption or desorption. The model's prediction of the tritium breakthrough trend observed in the NPD tests was poor; however, a forced fit can be achieved if the exchange rates in the MTZ and the unsaturated zone are manipulated. More experiments are needed to determine the relative rates of tritium exchange in the saturated, mass transfer, and unsaturated zones of a dryer bed

Energy savings by optimization of drying processes through use of models and effective control; Energibesparelser ved optimering af toerreprocesser gennem anvendelse af modeller og effektiv regulering

Energy Technology Data Exchange (ETDEWEB)

Didriksen, H.; Sandvig Nielsen, J.; Weel Hansen, M.

2001-06-01

The aim of the project is to present a procedure to optimize existing drying processes. The optimization deals with energy consumption, capacity utilization and product quality. Other factors can also be included in the optimization, e.g. minimization of volume of discharged air. The optimization of existing drying processes will use calculation tool based on a mathematical simulation model for the process to calculate the most optimum operation situation on the basis of given conditions. In the project mathematical models have been developed precisely with this aim. The calculation tools have been developed with a user interface so that the tools can be used by technical staff in industrial companies and by consultants. The project also illustrates control of drying processes. Based on the developed models, the effect of using different types of control strategies by means of model simulations is illustrated. Three types of drying processes are treated: drum dryers, disc dryers and drying chambers. The work with the development of the simulation models has been very central in the project, as these have to be the basis for the optimization of the processes. The work is based on a large amount of information from academical literature and knowledge and experience about modelling thermal processes at dk-TEKNIK. The models constitute the core in the simulation programmes. The models describe the most important physical effects in connection with mass and energy transfer and transport under the drying for the three treated drying technologies. (EHS)

A study of particle motion in rotary dryer

Directory of Open Access Journals (Sweden)

M. H. Lisboa

2007-09-01

Full Text Available The purpose of this work was to study the performance of a rotary dryer in relation to number of flights. In this work an equationing was proposed to calculate the area used by the solids in two-segment flights of with any angle between the segments. From this area, the flight holdup and the length of fall of the particles were calculated for different angle positions and the results obtained were compared to experimental values. The results show an increase in dryer efficiency with the increase in number of flights up to a limit value, for ideal operational conditions. The experimental data on average residence time were compared to results obtained by calculations using equations proposed in the literature. The equation proposed for predicting flight holdup and length of fall of particles generated very accurate estimations.

Performance of a solar dryer using hot air from roof-integrated solar collectors for drying herbs and spices

Energy Technology Data Exchange (ETDEWEB)

Janjai, S.; Tung, P. [Silpakorn University, Pathom (Thailand). Dept. of Physics

2005-11-01

A solar dryer for drying herbs and spices using hot air from roof-integrated solar collectors was developed. The dryer is a bin type with a rectangular perforated floor. The bin has a dimension of 1.0 m x 2.0 m x 0.7 m. Hot air is supplied to the dryer from fiberglass-covered solar collectors, which also function as the roof of a farmhouse. The total area of the solar collectors is 72 m{sup 2}. To investigate its performance, the dryer was used to dry four batches of rosella flowers and three batches of lemon-grasses during the year 2002-2003. The dryer can be used to dry 200 kg of rosella flowers and lemon-grasses within 4 and 3 days, respectively. The products being dried in the dryer were completely protected from rains and insects and the dried products are of high quality. The solar air heater has an average daily efficiency of 35% and it performs well both as a solar collector and a roof of a farmhouse. (author)

Analysis of heat conduction in a drum brake system of the wheeled armored personnel carriers

Science.gov (United States)

Puncioiu, A. M.; Truta, M.; Vedinas, I.; Marinescu, M.; Vinturis, V.

2015-11-01

This paper is an integrated study performed over the Braking System of the Wheeled Armored Personnel Carriers. It mainly aims to analyze the heat transfer process which is present in almost any industrial and natural process. The vehicle drum brake systems can generate extremely high temperatures under high but short duration braking loads or under relatively light but continuous braking. For the proper conduct of the special vehicles mission in rough terrain, we are talking about, on one hand, the importance of the possibility of immobilization and retaining position and, on the other hand, during the braking process, the importance movement stability and reversibility or reversibility, to an encounter with an obstacle. Heat transfer processes influence the performance of the braking system. In the braking phase, kinetic energy transforms into thermal energy resulting in intense heating and high temperature states of analyzed vehicle wheels. In the present work a finite element model for the temperature distribution in a brake drum is developed, by employing commercial finite element software, ANSYS. These structural and thermal FEA models will simulate entire braking event. The heat generated during braking causes distortion which modifies thermoelastic contact pressure distribution drum-shoe interface. In order to capture the effect of heat, a transient thermal analysis is performed in order to predict the temperature distribution transitional brake components. Drum brakes are checked both mechanical and thermal. These tests aim to establish their sustainability in terms of wear and the variation coefficient of friction between the friction surfaces with increasing temperature. Modeling using simulation programs led eventually to the establishment of actual thermal load of the mechanism of brake components. It was drawn the efficiency characteristic by plotting the coefficient of effectiveness relative to the coefficient of friction shoe-drum. Thus induced

Study on effectiveness of continuous solar dryer integrated with desiccant thermal storage for drying cocoa beans

Directory of Open Access Journals (Sweden)

Sari Farah Dina

2015-03-01

Full Text Available The main objective is to assess effectiveness of continuous solar dryer integrated with desiccant thermal storage for drying cocoa beans. Two type of desiccants were tested, molecular sieve 13× (Na86 [(AlO286·(SiO2106]·264H2O as an adsorbent type and CaCl2 as an absorbent type. The results revealed that during sunshine hours, the maximum temperature within the drying chamber varied from 40 °C to 54 °C. In average, it was 9–12 °C higher than ambient temperature. These temperatures are very suitable for drying cocoa beans. During off-sunshine hours, humidity of air inside the drying chamber was lower than ambient because of the desiccant thermal storage. Drying times for intermittent directs sun drying, solar dryer integrated with adsorbent, and solar dryer integrated with absorbent were 55 h, 41 h, and 30 h, respectively. Specific energy consumptions for direct sun drying, solar dryer integrated with adsorbent, and solar dryer integrated with absorber were 60.4 MJ/kg moist, 18.94 MJ/kg moist, and 13.29 MJ/kg moist, respectively. The main conclusion can be drawn here is that a solar dryer integrated with desiccant thermal storage makes drying using solar energy more effective in term of drying time and specific energy consumption.

The effect of fan speed control system on the inlet air temperature uniformity in a solar dryer

Directory of Open Access Journals (Sweden)

S. F Mousavi

2015-09-01

Full Text Available Introduction: Drying process of agricultural products, fruits and vegetables are highly energy demanding and hence are the most expensive postharvest operation. Nowadays, the application of control systems in different area of science and engineering plays a key role and is considered as the important and inseparable parts of any industrial process. The review of literature indicates that enormous efforts have been donefor the intelligent control of solar driers and in this regard some simulation models are used through computer programming. However, because of the effect of air velocity on the inlet air temperature in dryers, efforts have been made to control the fan speed based ont he temperature of the absorber plate in this study, and the behavior of this system was compared with an ordinary dryer without such a control system. Materials and methods: In this study, acabinet type solar dryer with forced convection and 5kg capacity of fresh herbs was used. The dryer was equipped with a fan in the outlet chamber (the chimney for creating air flow through the dryer. For the purpose of research methods and automatic control of fan speed and for adjusting the temperature of the drying inlet air, a control system consisting of a series of temperature and humidity sensors and a microcontroller was designed. To evaluatethe effect of the system with fan speed control on the uniformity of air temperature in the drying chamber and hence the trend of drying process in the solar dryer, the dryer has been used with two different modes: with and without the control of fan speed, each in twodays (to minimize the errors of almost the same ambient temperature. The ambient air temperature during the four days of experiments was obtained from the regional Meteorological Office. Some fresh mint plants (Mentha longifolia directly harvested from the farm in the morning of the experiment days were used as the drying materials. Each experimental run continued for 9

Numerical calculations of heat engineering parameters of a solar greenhouse dryer

International Nuclear Information System (INIS)

Akhatov, Zh.S.; Khalimov, A.S.

2015-01-01

The results of numerical simulation to determine the optimum volume of a thermal storage water heater in a solar greenhouse dryer are presented. A CAD (computer-aided design) model is created for the given installation by simulating the heat transfer processes with the aid of the Solid Works Flow Simulation software. The given CAD model consists of a concrete foundation and a steel frame in which translucent coatings made from two-layer polycarbonate sheets 6 mm in thickness with an air gap between the two layers are attached. The north wall is made of bricks with size and thickness of 2 x 4 m"2 and 0.4 m, respectively. The front surface has an angle of inclination 39.53 degree with respect to the horizontal surface for the maximum incidence of solar radiation to its surface. All the geometrical dimensions of the solar greenhouse dryer were selected on the basis of the allocated platform for the solar drying installation 3 x 4 m"2 in size. It is shown that the optimum volume of the heat storage tank for the present installation is 500 L. (authors)

Quantitative real-time monitoring of dryer effluent using fiber optic near-infrared spectroscopy.

Science.gov (United States)

Harris, S C; Walker, D S

2000-09-01

This paper describes a method for real-time quantitation of the solvents evaporating from a dryer. The vapor stream in the vacuum line of a dryer was monitored in real time using a fiber optic-coupled acousto-optic tunable filter near-infrared (AOTF-NIR) spectrometer. A balance was placed in the dryer, and mass readings were recorded for every scan of the AOTF-NIR. A partial least-squares (PLS) calibration was subsequently built based on change in mass over change in time for solvents typically used in a chemical manufacturing plant. Controlling software for the AOTF-NIR was developed. The software collects spectra, builds the PLS calibration model, and continuously fits subsequently collected spectra to the calibration, allowing the operator to follow the mass loss of solvent from the dryer. The results indicate that solvent loss can be monitored and quantitated in real time using NIR for the optimization of drying times. These time-based mass loss values have also been used to calculate "dynamic" vapor density values for the solvents. The values calculated are in agreement with values determined from the ideal gas law and could prove valuable as tools to measure temperature or pressure indirectly.

THE EFFECT OF THE THICKNESS OF A PACKED BED ON THE DYNAMIC AND THERMAL BEHAVIOR OF A SOLAR DRYER

Directory of Open Access Journals (Sweden)

S KHALDI

2015-06-01

Full Text Available Drying food in the sun is a safe, easy and economical way to preserve food, especially fruits. Cabinet dryers are the most popular equipment for fruit drying. Because of intermittent nature of solar energy, storage is required for uninterrupted supply in order to match the needs. The main objective of this study is to assess effectiveness of continuous solar dryer integrated with packed bed as thermal storage with natural airflow for drying figs (Ficuscarica. The cabinet dryer were envisaged theoretically (computational fluid dynamics (CFD. The distribution of the velocity and temperature of air within the solar dryer were presented during one day of August and under the climate conditions of Tlemcen (Algeria.  The effects of presence of a packed bed on the distribution of velocity and temperature of airflow and on the temperature of figs were analyzed. The results show that the solar dryer design, incorporating a packed bed enhances the capabilities and performance of the solar dryer, through increasing time of drying.

Drying of mint leaves in a solar dryer and under open sun: Modelling, performance analyses

International Nuclear Information System (INIS)

Akpinar, E. Kavak

2010-01-01

In this study was investigated the thin-layer drying characteristics in solar dryer with forced convection and under open sun with natural convection of mint leaves, and, performed energy analysis and exergy analysis of solar drying process of mint leaves. An indirect forced convection solar dryer consisting of a solar air collector and drying cabinet was used in the experiments. The drying data were fitted to ten the different mathematical models. Among the models, Wang and Singh model for the forced solar drying and the natural sun drying were found to best explain thin-layer drying behaviour of mint leaves. Using the first law of thermodynamics, the energy analysis throughout solar drying process was estimated. However, exergy analysis during solar drying process was determined by applying the second law of thermodynamics. Energy utilization ratio (EUR) values of drying cabinet varied in the ranges between 7.826% and 46.285%. The values of exergetic efficiency were found to be in the range of 34.760-87.717%. The values of improvement potential varied between 0 and 0.017 kJ s -1 . Energy utilization ratio and improvement potential decreased with increasing drying time and ambient temperature while exergetic efficiency increased.

Artificial neural networks in the evaluation of the radioactive waste drums activity

International Nuclear Information System (INIS)

Potiens, J.R.A.J.; Hiromoto, G.

2006-01-01

The mathematical techniques are becoming more important to solve geometry and standard identification problems. The gamma spectrometry of radioactive waste drums would be a complex solution problem. The main difficulty is the detectors calibration for this geometry; the waste is not homogeneously distributed inside the drums, therefore there are many possible combinations between the activity and the position of these radionuclides inside the drums, making the preparation of calibration standards impracticable. This work describes the development of a methodology to estimate the activity of a 200 L radioactive waste drum, as well as a mapping of the waste distribution, using Artificial Neural Network. The neural network data set entry obtaining was based on the possible detection efficiency combination with 10 sources activities varying from 0 to 74 x 10 3 Bq. The set up consists of a 200 L drum divided in 5 layers. Ten detectors were positioned all the way through a parallel line to the drum axis, from 15 cm of its surface. The Cesium -137 radionuclide source was used. The 50 efficiency obtained values (10 detectors and 5 layers), combined with the 10 source intensities resulted in a 100,000 lines for 15 columns matrix, with all the possible combinations of source intensity and the Cs-137 position in the 5 layers of the drum. This archive was divided in 2 parts to compose the set of training: input and target files. The MatLab 7.0 module of neural networks was used for training. The net architecture has 10 neurons in the input layer, 18 in the hidden layer and 5 in the output layer. The training algorithm was the 'traincgb' and after 300 'epoch s' the medium square error was 0.00108172. This methodology allows knowing the detection positions answers in a heterogeneous distribution of radionuclides inside a 200 L waste drum; in consequence it is possible to estimate the total activity of the drum in the training neural network limits. The results accuracy depends

Active drumming experience increases infants' sensitivity to audiovisual synchrony during observed drumming actions

NARCIS (Netherlands)

Gerson, S.A.; Schiavio, A.A.R.; Timmers, R.; Hunnius, S.

2015-01-01

In the current study, we examined the role of active experience on sensitivity to multisensory synchrony in six-month-old infants in a musical context. In the first of two experiments, we trained infants to produce a novel multimodal effect (i.e., a drum beat) and assessed the effects of this

Field measurements of temperature profile for floatovoltaic dryer in the tropics

Science.gov (United States)

Osman, F. A.; Ya'acob, M. E.; Iskandar, A. Noor

2017-09-01

Most of the equator region in a tropical climate zone experiences hot and humid weather but sometimes heavy rain and thunderstorms which occur stochastically in monsoon season. Sunlight which is the energy source can be harvested approximately 8 hours (on average basis) daily throughout the year which leads to the promotion of Solar PV technologies. This works projects the field performance for a new Floatovoltaic Dryer prototype with flexible PV roofing structures covering the top of the dryer system. The field measurements are collected on the lake of Engineering Faculty, UPM supported with 4-parameter weather station. Temperature profile with RH measurements inside the Floatovoltaic Dryer compartments as compared to direct-sun drying mechanism are the main contributions of this work and it projects more than 12 W of convection heat energy could be harvested by using the clean system. The field measurements imply various points of thermocouple and humidity sensor throughout the experiment. Temperature and humidity will be the main elements recorded to analyze the differences under monocrystalline PV panel as compared to natural drying.

Operational Augmentation of Forced Circulation Type Solar Dryer System Using CFD Analysis

OpenAIRE

Atul Patel; Gaurav Patel

2014-01-01

Solar drying is basically heat and mass transfer process in which the liquid water from the surface and the vapour removed by draft. The efficiency of a solar drying system is affected by the properties of drying materials.e.g. size, shape and geometry as well as ambient conditions. In this research article, the authors have done the CFD analysis of a Forced Circulation type Solar Dryer used conventionally for dehydrating vegetables and fruits. Using CFD analysis, the limiting...

Development and engineering application of rotating drum acid-curing equipment in uranium mills

International Nuclear Information System (INIS)

Liu Wenhua

2006-01-01

The development and engineering application of rotating drum acid-curing equipment for 'strong acid-curing and ferri-trickle leaching' process are introduced, including the design of main structure, problems appeared in the development and engineering application, and methods solved. (authors)

Design and development of a connection of a magnetic drum with two computers

International Nuclear Information System (INIS)

Malriq, Jean.

1976-01-01

In the experiment in High Energy Physics 'Hyperons SPS' realized at the CERN 300 GeV the connection between a drum and two computers is studied. One of the two computers is a NORD-10 the other may be anyone if it has a CAMAC interface. The input/output structure of the NORD-10 has been studied, then the interface NORD-drum and the CAMAC-drum interface have been realized. The electronic commutation allowing each computer to be connected on the drum through its specific interface has been built [fr

Impact of flow induced vibration acoustic loads on the design of the Laguna Verde Unit 2 steam dryer

International Nuclear Information System (INIS)

Forsyth, D. R.; Wellstein, L. F.; Theuret, R. C.; Han, Y.; Rajakumar, C.; Amador C, C.; Sosa F, W.

2015-09-01

Industry experience with Boiling Water Reactors (BWRs) has shown that increasing the steam flow through the main steam lines (MSLs) to implement an extended power up rate (EPU) may lead to amplified acoustic loads on the steam dryer, which may negatively affect the structural integrity of the component. The source of these acoustic loads has been found to be acoustic resonance of the side branches on the MSLs, specifically, coupling of the vortex shedding frequency and natural acoustic frequency of safety relief valves (SRVs). The resonance that results from this coupling can contribute significant acoustic energy into the MSL system, which may propagate upstream into the reactor pressure vessel steam dome and drive structural vibration of steam dryer components. This can lead to high-cycle fatigue issues. Lock-in between the vortex shedding frequency and SRV natural frequency, as well as the ability for acoustic energy to propagate into the MSL system, are a function of many things, including the plant operating conditions, geometry of the MSL/SRV junction, and placement of SRVs with respect to each other on the MSLs. Comision Federal de Electricidad and Westinghouse designed, fabricated, and installed acoustic side branches (ASBs) on the MSLs which effectively act in the system as an energy absorber, where the acoustic standing wave generated in the side-branch is absorbed and dissipated inside the ASB. These ASBs have been very successful in reducing the amount of acoustic energy which propagates into the steam dome. In addition, modifications to the Laguna Verde Nuclear Power Plant Unit 2 steam dryer have been completed to reduce the stress levels in critical locations in the dryer. The objective of this paper is to describe the acoustic side branch concept and the design iterative processes that were undertaken at Laguna Verde Unit 2 to achieve a steam dryer design that meets the guidelines of the American Society of Mechanical Engineers, Boiler and Pressure

Impact of flow induced vibration acoustic loads on the design of the Laguna Verde Unit 2 steam dryer

Energy Technology Data Exchange (ETDEWEB)

Forsyth, D. R.; Wellstein, L. F.; Theuret, R. C.; Han, Y.; Rajakumar, C. [Westinghouse Electric Company LLC, Cranberry Township, PA 16066 (United States); Amador C, C.; Sosa F, W., E-mail: forsytdr@westinghouse.com [Comision Federal de Electricidad, Central Nucleoelectrica Laguna Verde, Km 42.5 Carretera Cardel-Nautla, 91680 Alto Lucero, Veracruz (Mexico)

2015-09-15

Industry experience with Boiling Water Reactors (BWRs) has shown that increasing the steam flow through the main steam lines (MSLs) to implement an extended power up rate (EPU) may lead to amplified acoustic loads on the steam dryer, which may negatively affect the structural integrity of the component. The source of these acoustic loads has been found to be acoustic resonance of the side branches on the MSLs, specifically, coupling of the vortex shedding frequency and natural acoustic frequency of safety relief valves (SRVs). The resonance that results from this coupling can contribute significant acoustic energy into the MSL system, which may propagate upstream into the reactor pressure vessel steam dome and drive structural vibration of steam dryer components. This can lead to high-cycle fatigue issues. Lock-in between the vortex shedding frequency and SRV natural frequency, as well as the ability for acoustic energy to propagate into the MSL system, are a function of many things, including the plant operating conditions, geometry of the MSL/SRV junction, and placement of SRVs with respect to each other on the MSLs. Comision Federal de Electricidad and Westinghouse designed, fabricated, and installed acoustic side branches (ASBs) on the MSLs which effectively act in the system as an energy absorber, where the acoustic standing wave generated in the side-branch is absorbed and dissipated inside the ASB. These ASBs have been very successful in reducing the amount of acoustic energy which propagates into the steam dome. In addition, modifications to the Laguna Verde Nuclear Power Plant Unit 2 steam dryer have been completed to reduce the stress levels in critical locations in the dryer. The objective of this paper is to describe the acoustic side branch concept and the design iterative processes that were undertaken at Laguna Verde Unit 2 to achieve a steam dryer design that meets the guidelines of the American Society of Mechanical Engineers, Boiler and Pressure

Thermal hydraulic aspects of steam drum level control philosophy for the natural circulation based heavy water reactor

International Nuclear Information System (INIS)

Gupta, S.K.; Gaikwad, A.J.; Kumar, Rajesh

2004-01-01

From safety considerations advanced nuclear reactors rely more and more on passive systems such as natural circulation for primary heat removal. A natural circulation based water reactor is relatively larger in size so as to reduce flow losses and channel type for proper flow distribution. From the size of steam drum considerations it has to be multi loop but has a common inlet header. Normally the turbine follows the reactor. This paper addresses the thermal hydraulic aspects of the steam drum pressure and level control philosophy for a four drum, natural circulation based, channel type boiling water advanced reactor. Three philosophies may be followed for drum control viz. individual drum control, one control drum approach and an average of all the four drums. For drum pressure control, the steam flow to the turbine is be regulated. A single point pressure control is better than individual drum pressure control. This is discussed in the paper. But the control point has to be at a place down steam the point where all steam line from individual drum meet. This may lead to different pressure in all the four drums depending on the power produced in the respective loops. The difference in pressure cannot be removed even if the four drums are directly connected through pipes. Also the pressure control scheme with/without interconnection is discussed. For level, the control of individual drum may not be normally possible because of common inlet header. As the frictional pressure drops in the large diameter downcomers are small as compared to elevation pressure drops, the level in all the steam drum tend to equalize. Consequently a single representative drum level may be chosen as a control variable for controlling level in all the four drums. But in case, where all the four loops are producing different powers and single point pressure control is effective, the scheme may not work satisfactorily. the level in a drum may depend on the power produced in the loop

A verification calculation of drum and pulley overhead travelling crane on gamma irradiator ISG-500

International Nuclear Information System (INIS)

Syamsurrijal Ramdja; Ari Satmoko; Sutomo Budihardjo

2010-01-01

It has been verified the calculation of drum and pulleys on cranes as facility the gamma irradiator ISG-500. Drum is a device for rolling steel ropes while the pulley is a circular pieces called disks, and both of which are made from metal or non-metal to transmit motion and force. It has been verified the calculation of forces on the drum, drum diameter and length, and pressuring force occurred on the drums. Likewise to the pulley, the pulley diameter calculations verification, size of disc and shaft power pulleys. From the verification results, it will be obtained whether the data drums and pulley device are safe or not safe to be used. (author)

DEM simulation of particle mixing for optimizing the overcoating drum in HTR fuel fabrication

Science.gov (United States)

Liu, Malin; Lu, Zhengming; Liu, Bing; Shao, Youlin

2013-06-01

The rotating drum was used for overcoating coated fuel particles in HTR fuel fabrication process. All the coated particles should be adhered to equal amount of graphite powder, which means that the particle should be mixed quickly in both radial and axial directions. This paper investigated the particle flow dynamics and mixing behavior in different regimes using the discrete element method (DEM). By varying the rotation speed, different flow regimes such as slumping, rolling, cascading, cataracting, centrifuging were produced. The mixing entropy based on radial and axial grid was introduced to describe the radial and axial mixing behaviors. From simulation results, it was found that the radial mixing can be achieved in the cascading regime more quickly than the slumping, rolling and centrifuging regimes, but the traditional rotating drum without internal components can not achieve the requirements of axial mixing and should be improved. Three different structures of internal components are proposed and simulated. The new V-shaped deflectors were found to achieve a quick axial mixing behavior and uniform axial distribution in the rotating drum based on simulation results. At last, the superiority was validated by experimental results, and the new V-shaped deflectors were used in the industrial production of the overcoating coated fuel particles in HTR fuel fabrication process.

49 CFR 178.506 - Standards for metal drums other than steel or aluminum.

Science.gov (United States)

2010-10-01

... aluminum. 178.506 Section 178.506 Transportation Other Regulations Relating to Transportation PIPELINE AND... drums other than steel or aluminum. (a) The following are the identification codes for metal drums other than steel or aluminum: (1) 1N1 for a non-removable head metal drum; and (2) 1N2 for a removable head...

A model of gas generation and transport within TRU [transuranic] waste drums

International Nuclear Information System (INIS)

Smith, F.G. III.

1987-01-01

Gas generation from the radiolytic decomposition of organic material contaminated with plutonium is modeled. Concentrations of gas throughout the waste drum are determined using a diffusional transport model. The model accurately reproduces experimentally measured gas concentrations. With polyethylene waste in unvented drums, the model predicts that hydrogen gas can accumulate to concentrations greater than 4 mole percent (lower flammable limit) with about 5 Ci of plutonium. Polyethylene provides a worst case for combustible waste material. If the drum liner is punctured and a carbon composite filter vent is installed in the drum lid, the plutonium loading can be increased to 240 Ci without generating flammable gas mixtures. 5 refs., 7 figs., 4 tabs

Simulation Modeling of Non-Homogeneous Mixture in the Horizontal Drum Mixer

Directory of Open Access Journals (Sweden)

Andrey Vladimirovich Ostroukh

2015-05-01

Full Text Available The paper proposes a simulation model of the diffusion mixing of solids, based on the theory of probability and stochastic diffusion model of imperfect processes of solid particles. It is assumed that the particles have different sizes and density. Model of the program implemented in the AnyLogic SoftWare. Developed a simulation model to evaluate the differences between the intense mixing processes in time and assess their impact on the course of other processes in a horizontal drum mixer.

Device to measure level in a steam drum of NPP

International Nuclear Information System (INIS)

Vinogradov, Yu.A.

1988-01-01

Gravitation-hydrostatic device for measuring coolant level in a steam drum of NPP is described. The device enables to improve the accuracy and sensitivity of measuring coolant level above and below the submerged perforated sheet of the steam drum and decrease the amount of levelling vessels in the unit by 50%. 1 fig

Characterization of void volume VOC concentration in vented TRU waste drums - an interim report

International Nuclear Information System (INIS)

Liekhus, K.J.

1994-09-01

A test program is underway at the Idaho National Engineering Laboratory to determine if the concentration of volatile organic compounds (VOCs) in the drum headspace is representative of the VOC concentration in the entire drum void space and to demonstrate that the VOC concentration in the void space of each layer of confinement can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. An experimental test plan was developed requiring gas sampling of 66 transuranic (TRU) waste drums. This interim report summarizes the experimental measurements and model predictions of VOC concentration in the innermost layer of confinement from waste drums sampled and analyzed in FY 1994

The method study for nuclide analysis of waste drum

International Nuclear Information System (INIS)

Ruan Guanglin; Huang Xianguo; Xing Shixiong

2001-01-01

The principle of waste drum nuclide analysis system and the principle of the detector chosen are introduced. The linear attenuation coefficient and mass attenuation coefficient of five environmental medium (water, soil, red brick, concrete and sands) have been measured with γ transmission method simulative equipment. The absorption coefficient and nuclide activity of three measuring conditions (collimation-columnar source, un-collimation-columnar source, and un-collimation-rotation-drum source) have been calculated

Possibilities of rotating drums in ultra-high-speed cinematography

International Nuclear Information System (INIS)

Andre, Michel

A theoretical study shows that it is possible to produce a drum rotating at a peripheral speed of 500m/s. A prototype has actually reached this speed and confirmed the feasibility of the system. It is driven by an electric motor and is made of titanium covered with boron fibres. The main performances to be expected of cameras (whole-image, slit or spectrographic) using such a drum is described [fr

ANALYSIS OF DESIGN PECULIARITIES PERTAINING TO DRUMS OF CONTINUOUS MACHINES

Directory of Open Access Journals (Sweden)

V. Yu. Prushak

2007-01-01

Full Text Available The paper considers design peculiarities of belt conveyor drums in respect of their operational reliability; their advantages and disadvantages have been analyzed. There are some proposals presenting technical solutions to modernization of belt conveyor drum designs which presuppose reduction of their material consumption while preserving their strength and general rigidity. 

Protein Concentrate Production from Thin Stillage.

Science.gov (United States)

Ratanapariyanuch, Kornsulee; Shim, Youn Young; Emami, Shahram; Reaney, Martin J T

2016-12-21

Two-stage fermentation (TSF) of saccharified wheat with a consortium of endemic lactobacilli produced CO 2 and induced colloid separation of fermented solution to produce a protein concentrate (PC). Protein-rich slurry (50%, db) was obtained by decanting solution or skimming floating material during or after TSF. Washing and drying processes were explored to improve protein content, extend storage life of slurry, and yield converted stillage for compound recovery. Centrifuging and washing slurry afforded a PC and clarified solution. PC protein content increased to 60% (w/w, db). The PC was dried in a spray dryer or drum dryer or tray dryer. Dried PC water activity ranged 0.23-0.30. The dried PC lysine content was low, but lysine availability (95%) was excellent. Liquid from TSF and washing was readily microfiltered. Mass recovery of protein, glycerol, 1,3-propanediol, lactic acid, acetic acid, and glycerylphosphorylcholine from combined TSF, washing, and filtration were 66, 76, 72, 77, 74, and 84%, respectively.

Analytical and experimental evaluation of solid waste drum fire performance volumes I and II

Energy Technology Data Exchange (ETDEWEB)

Hecker, C.F., [Los Alamos Technical Associates, Inc., Kennewick, WA (United States); Rhodes, B.T.; Beitel, J.J.; Gottuk, D.T.; Beyler, C.L.; Rosenbaum, E.R., [Hughes Associates, Inc., Columbia, MD (United States)

1995-04-28

Fire hazards associated with drum storage of radioactively contaminated wastes are a major concern in DOE facilities design for long term storage of solid wastes in drums. These facilities include drums stored in pallet arrays and in rack storage systems. This report details testing in this area

Experimental investigation on energy and exergy analysis of coriander (Coriadrum sativum L.) leaves drying in natural convection solar dryer

International Nuclear Information System (INIS)

Panwar, N.L.

2014-01-01

This study deals with thin layer drying characteristics of Coriandrum sativum L. leaves in a natural convection solar dryer. The Coriandrum sativum L. leaves were dried from a moisture content of 88% (w.b.) to 4.5% (w.b.) in 7.5 hours. The obtained drying data were fitted to eight different drying kinetics models. Of these, the model suggested by Midilli et al. [20] had the best fit with the drying behavior of Coriandrum sativum L. leaves. In addition, the thermodynamic behaviour of a solar dryer was evaluated. The energy efficiency during the study varied from 7.81 to 37.93%. The exergy efficiency of the drying process ranged between 55.35 and 79.39%. (author)

Techniques for improving shuffler assay results for 55-gallon waste drums

International Nuclear Information System (INIS)

Rinard, P.M.; Prettyman, T.H.; Stuenkel, D.

1994-01-01

Accurate assays of the fissile contents in waste drums are needed to ensure the most proper and economical handling and disposal of the waste. An improvement of accuracy will mean fewer drums disposed as transuranic waste when they really contain low-level waste, saving both money and burial sites. Shufflers are used for assaying waste drums and are very accurate with nonmoderating matrices (such as iron). In the active mode they count delayed neutrons released after fissions are induced by irradiation neutrons from a 252 Cf source. However, as the hydrogen density from matrices such as paper or gloves increases, the accuracy can suffer without proper attention. The neutron transport and fission probabilities change with the hydrogen density, causing the neutron count rate to vary with the position of the fissile material within the drum. The magnitude of this variation grows with the hydrogen density

A study of the drying effect on lemon slices using a closed-type solar dryer

Energy Technology Data Exchange (ETDEWEB)

Ho-Hsien Chen; Hernandez, C.E.; Tzou-Chi Huang [National Pingtung University of Science and Technology (China). Dept. of Food Science

2005-01-01

An experimental closed-type dryer associated with a photovoltaic system (PV) was developed. The transparent drying cabinet was designed with high transmittance glass to decrease the reflection of direct sunlight and to offer extra direct solar heating on the raw material during drying. Parallel wiring with a local electrical grid was necessary for switching purposes if there is insufficient battery backup during peak operation. Lemon slices were dried using the closed-type solar dryer and results were compared with hot air drying at 60{sup o}C. The results indicate that the dried lemon slices using a closed-type solar dryer has better general levels of quality in terms of sensory parameters. (author)

EARLY TESTS OF DRUM TYPE PACKAGINGS - THE LEWALLEN REPORT

Energy Technology Data Exchange (ETDEWEB)

Smith, A.

2010-07-29

The need for robust packagings for radioactive materials (RAM) was recognized from the earliest days of the nuclear industry. The U.S. Department of Energy (DOE) Rocky Flats Plant developed a packaging for shipment of Pu in the early 1960's, which became the U.S. Department of Transportation (DOT) 6M specification package. The design concepts were employed in other early packagings. Extensive tests of these at Savannah River Laboratory (now Savannah River National Laboratory) were performed in 1969 and 1970. The results of these tests were reported in 'Drum and Board-Type Insulation Overpacks of Shipping Packages for Radioactive Materials', by E. E. Lewallen. The Lewallen Report was foundational to design of subsequent drum type RAM packaging. This paper summarizes this important early study of drum type packagings. The Lewallen Report demonstrated the ability packagings employing drum and insulation board overpacks and engineered containment vessels to meet the Type B package requirements. Because of the results of the Lewallen Report, package designers showed high concern for thermal protection of 'Celotex'. Subsequent packages addressed this by following strategies like those recommended by Lewallen and by internal metal shields and supplemental, encapsulated insulation disks, as in 9975. The guidance provide by the Lewallen Report was employed in design of a large number of drum size packagings over the following three decades. With the increased public concern over transportation of radioactive materials and recognition of the need for larger margins of safety, more sophisticated and complex packages have been developed and have replaced the simple packagings developed under the Lewallen Report paradigm.

Reconstruction of the isotope activity content of heterogeneous nuclear waste drums.

Science.gov (United States)

Krings, Thomas; Mauerhofer, Eric

2012-07-01

Radioactive waste must be characterized in order to verify its conformance with national regulations for intermediate storage or its disposal. Segmented gamma scanning (SGS) is a most widely applied non-destructive analytical technique for the characterization of radioactive waste drums. The isotope specific activity content is generally calculated assuming a homogeneous matrix and activity distribution for each measured drum segment. However, real radioactive waste drums exhibit non-uniform isotope and density distributions most affecting the reliability and accuracy of activities reconstruction in SGS. The presence of internal shielding structures in the waste drum contributes generally to a strong underestimation of the activity and this in particular for radioactive sources emitting low energy gamma-rays independently of their spatial distribution. In this work we present an improved method to quantify the activity of spatially concentrated gamma-emitting isotopes (point sources or hot spots) in heterogeneous waste drums with internal shielding structures. The isotope activity is reconstructed by numerical simulations and fits of the angular dependent count rate distribution recorded during the drum rotation in SGS using an analytical expression derived from a geometric model. First results of the improved method and enhancements of this method are shown and are compared to each other as well as to the conventional method which assumes a homogeneous matrix and activity distribution. It is shown that the new model improves the accuracy and the reliability of the activity reconstruction in SGS and that the presented algorithm is suitable with respect to the framework requirement of industrial application. Copyright © 2011 Elsevier Ltd. All rights reserved.

Study on the dynamic performance of concrete mixer's mixing drum

Directory of Open Access Journals (Sweden)

J. Yang

2017-06-01

Full Text Available When working, the geometric distribution shape of concrete in concrete mixing truck's rotary drum changes continuously, which cause a great difficulty for studying the dynamic performance of the mixing drum. In this paper, the mixing system of a certain type of concrete mixing truck is studied. A mathematical formulation has been derived through the force analysis to calculate the supporting force. The calculation method of the concrete distribution shape in the rotary drum is developed. A new transfer matrix is built with considering the concrete geometric distribution shape. The effects of rotating speed, inclination angle and concrete liquid level on the vibration performance of the mixing drum are studied with a specific example. Results show that with the increase of rotating speed, the vibration amplitude of the mixing drum decreases. The peak amplitude gradually moves to the right with the inclination angle increasing. The amplitude value of the peak's left side decreases when tilt angle increases, while the right side increases. The maximum unbalanced response amplitude of the drum increases with the decrease of concrete liquid level height, and the vibration peak moves to the left.

Renewable Energy Opportunities at Fort Drum, New York

Energy Technology Data Exchange (ETDEWEB)

Brown, Scott A.; Orrell, Alice C.; Solana, Amy E.; Williamson, Jennifer L.; Hand, James R.; Russo, Bryan J.; Weimar, Mark R.; Rowley, Steven; Nesse, Ronald J.

2010-10-20

This document provides an overview of renewable resource potential at Fort Drum, based primarily upon analysis of secondary data sources supplemented with limited on-site evaluations. This effort focuses on grid-connected generation of electricity from renewable energy sources and also on ground source heat pumps for heating and cooling buildings. The effort was funded by the U.S. Army Installation Management Command (IMCOM) as follow-on to the 2005 Department of Defense (DoD) Renewables Assessment. The site visit to Fort Drum took place on May 4 and 5, 2010.

Considerations for an active and passive scanner to assay nuclear waste drums

International Nuclear Information System (INIS)

Martz, H.E.; Azevedo, S.G.; Roberson, G.P.; Schneberk, D.J.; Koenig, Z.M.; Camp, D.C.

1990-01-01

Radioactive wastes are generated at many DOE laboratories, military facilities, fuel fabrication and enrichment plants, reactors, hospitals, and university research facilities. At all of these sites, wastes must be separated, packaged, categorized, and packed into some sort of container--usually 208-L (55-gal) drums--for shipment to waste-storage sites. Prior to shipment, the containers must be labeled, assayed, and certified; the assay value determines the ultimate disposition of the waste containers. An accurate nondestructive assay (NDA) method would identify all the radioisotopes present and provide a quantitative measurement of their activity in the drum. In this way, waste containers could be routed in the most cost-effective manner and without having to reopen them. Currently, the most common gamma-ray method used to assay nuclear waste drums is segmented gamma-ray scanning (SGS) spectrometer that crudely measures only the amount of 235 U or 239 Pu present in the drum. This method uses a spatially-averaged, integrated, emitted gamma-ray-intensity value. The emitted intensity value is corrected by an assumed constant-attenuation value determined by a spatially-averaged, transmission (or active) measurement. Unfortunately, this typically results in an inaccurate determination of the radioactive activities within a waste drum because this measurement technique is valid only for homogeneous-attenuation or known drum matrices. However, since homogeneous-attenuation matrices are not common and may be unknown, other NDA techniques based on active and Passive CT (A ampersand PCT) are under development. The active measurement (ACT) yields a better attenuation matrix for the drum, while the passive measurement (PCT) more accurately determines the identity of the radioisotopes present and their activities. 9 refs., 2 figs

Performance Evaluation of a Pebble Bed Solar Crop Dryer ...

African Journals Online (AJOL)

Nigerian Journal of Technology ... The solar crop dryer consists of an imbedded pebble bed solar heat storage unit/solar collector ... The crop-drying chamber is made of drying trays of wire gauze while the roof is made of transparent glazing.

US Department of Transportation (DOT) Spec 7A Type A evaluation document: Spec 17C 55-gal steel drum with RWMC/SWEPP drum venting system carbon filter assembly

International Nuclear Information System (INIS)

Edling, D.A.

1986-01-01

As part of MRC-Mound's responsibility to coordinate DOE Spec 7A Type A Packaging testing, evaluation, and utilization, this document evaluates per 49CFR 173.415(a) the SWEPP packaging system: DOT Spec 17C steel drums - 30, 55 and 83-gal; High Density Polyethylene (HDPE) liners; and SWEPP DVS Filter Assemblies (two configurations) as a US DOT Spec 7A Type A packaging. A variety of Type A performance testing was done on: DOT Spec 17C 55-gal steel drums; DOT Spec 17C 55-gal steel drums with HDPE liners; and DOT Spec 17C 55-gal steel drums with ''Nucfil'' filters as part of MRC-Mound's Type A Packaging Evaluation Program funded by DOE/HQ, DP-4, Security Evaluations. The subject SWEPP packaging incorporates modifications to the ''Nucfil'' filter and installation assembly previously tested in conjunction with the Spec 17C 55-gal drums. Thus, additional testing was required on the new filter installation in order to evaluate the entire packaging system. This document presents the test data to demonstrate the SWEPP packaging system's performance against the DOT 7A Type A requirements

Design and Fabrication of a Direct Natural Convection Solar Dryer for Tapioca

Directory of Open Access Journals (Sweden)

Diemuodeke E. OGHENERUONA

2011-06-01

Full Text Available Based on preliminary investigations under controlled conditions of drying experiments, a direct natural convection solar dryer was designed and fabricated to dry tapioca in the rural area. This paper describes the design considerations followed and presents the results of MS excel computed results of the design parameters. A minimum of 7.56 m2 solar collector area is required to dry a batch of 100 kg tapioca in 20 hours (two days drying period. The initial and final moisture content considered were 79 % and 10 % wet basis, respectively. The average ambient conditions are 32ºC air temperatures and 74 % relative humidity with daily global solar radiation incident on horizontal surface of 13 MJ/m2/day. The weather conditions considered are of Warri (lat. 5°30’, long. 5°41’, Nigeria. A prototype of the dryer so designed was fabricated with minimum collector area of 1.08 m2. This prototype dryer will be used in experimental drying tests under various loading conditions.

Modelling the drying kinetics of green peas in a solar dryer and under open sun

Energy Technology Data Exchange (ETDEWEB)

Sunil [Department of Mechanical Engineering, BRCM CET Bahal, Haryana–127028 (India); Varun [Department of Mechanical Engineering, NIT Hamirpur, (H.P.)–177005 (India); Sharma, Naveen [Department of Mechanical and Industrial Engineering, IITR, (U.K.)–247667 (India)

2013-07-01

The drying kinetics of green peas was investigated in an indirect solar dryer and under open sun. The entire drying process took place exclusively in falling rate period. The constant rate period was absent from the drying curves. The rehydration capacity was also determined for peas dried in solar dryer and under open sun. The rehydration capacity of solar dried peas was found higher than open sun dried peas. The drying data obtained from experiments were fitted to eight different mathematical models. The performance of these models was examined by comparing the coefficient of correlation (R2), sum of squares error (SSE), mean squared error (MSE) and root mean square error (RMSE) between observed and predicted values of moisture ratios. Among these models, the thin layer drying model developed by Page showed good agreement with the data obtained from experiments for bottom tray. The Midilli et al. model has shown better fit to the experimental data for top tray and open sun than other models.

Natural convection solar crop dryers in Kenya: Theory and practical application. African Energy Programme research report series no. 3

International Nuclear Information System (INIS)

Othieno, H.

1987-01-01

design also has succeeded in solving the identified problems associated with the tradition sun drying techniques. One would therefore expect the demand for these dryers to be high. The actual situation is different. Farmers are not willing to spend money to acquire the dryers. Perhaps this is attributed to the fact that there is still high level of underemployment (or unemployment) of rural population and the fact that traditional drying method does not cost anything. Moreover the land area required for spreading the crops is still abundant in the rural areas. The farmers therefore appear not to appreciate the advantages of the solar dryer. Due to seasonal maize shortages which occasionally occur in Kenya, the government is now emphasizing the need to preserve cereal grains through proper drying and storage facilities. Expensive large oil-fired dryers have been imported and the government, through National Cereals and Produce Board, spends a lot of money to run these dryers. If small scale solar crop dryers were used at the farm level so that all cereal grains reaching the National Cereals and Produce Board were dry to the required moisture content for- long term storage, the government would save on the imported oil needed to operate the large industrial dryers. The individual farmer does not realize this and it is high time the government adopted a firm policy on the promotion of renewable energy devices. The policy should aim at assisting not only in educating the farmers but also in supporting researchers to disseminate knowledge about these devices. Relevant government ministries e.g. Ministry of Energy and Regional Development, Ministry of Agriculture and Ministry of Environment and Natural Resources should actively be involved in the dissemination process through Newspapers, Radio and T.V. Perhaps the Kenya National Council for Science and Technology should play a coordinating role

Natural convection solar crop dryers in Kenya: Theory and practical application. African Energy Programme research report series no. 3

Energy Technology Data Exchange (ETDEWEB)

Othieno, H [Kenyatta University, Nairobi (Kenya)

1987-07-01

design also has succeeded in solving the identified problems associated with the tradition sun drying techniques. One would therefore expect the demand for these dryers to be high. The actual situation is different. Farmers are not willing to spend money to acquire the dryers. Perhaps this is attributed to the fact that there is still high level of underemployment (or unemployment) of rural population and the fact that traditional drying method does not cost anything. Moreover the land area required for spreading the crops is still abundant in the rural areas. The farmers therefore appear not to appreciate the advantages of the solar dryer. Due to seasonal maize shortages which occasionally occur in Kenya, the government is now emphasizing the need to preserve cereal grains through proper drying and storage facilities. Expensive large oil-fired dryers have been imported and the government, through National Cereals and Produce Board, spends a lot of money to run these dryers. If small scale solar crop dryers were used at the farm level so that all cereal grains reaching the National Cereals and Produce Board were dry to the required moisture content for- long term storage, the government would save on the imported oil needed to operate the large industrial dryers. The individual farmer does not realize this and it is high time the government adopted a firm policy on the promotion of renewable energy devices. The policy should aim at assisting not only in educating the farmers but also in supporting researchers to disseminate knowledge about these devices. Relevant government ministries e.g. Ministry of Energy and Regional Development, Ministry of Agriculture and Ministry of Environment and Natural Resources should actively be involved in the dissemination process through Newspapers, Radio and T.V. Perhaps the Kenya National Council for Science and Technology should play a coordinating role.

Electromechanical dynamic analysis for the drum driving system of the long-wall shearer

Directory of Open Access Journals (Sweden)

Changzhao Liu

2015-10-01

Full Text Available The drum driving system is one of the weakest parts of the long-wall shearer, and some methods are also needed to monitor and control the long-wall shearer to adapt to the important trend of unmanned operation in future mining systems. Therefore, it is essential to conduct an electromechanical dynamic analysis for the drum driving system of the long-wall shearer. First, a torsional dynamic model of planetary gears is proposed which is convenient to be connected to the electric motor model for electromechanical dynamic analysis. Next, an electromechanical dynamic model for the drum driving system is constructed including the electric motor, the gear transmission system, and the drum. Then, the electromechanical dynamic characteristics are simulated when the shock loads are acted on the drum driving system. Finally, some advices are proposed for improving the reliability, monitoring the operating state, and choosing the control signals of the long-wall shearer based on the simulation.

Characterization of voic volume VOC concentration in vented TRU waste drums. Final report

Energy Technology Data Exchange (ETDEWEB)

Liekhus, K.J.

1994-12-01

A test program has been conducted at the Idaho National Engineering Laboratory to demonstrate that the concentration of volatile organic compounds within the innermost layer of confinement in a vented waste drum can be estimated using a model incorporating diffusion and permeation transport principles and limited waste drum sampling data. This final report summarizes the experimental measurements and model predictions for transuranic waste drums containing solidified sludges and solid waste.

Comprehensive investigation of the metal in drums of boilers at thermal power stations

Science.gov (United States)

Ozhigov, L. S.; Mitrofanov, A. S.; Tolstolutskaya, G. D.; Vasilenko, R. L.; Rudenko, A. G.; Ruzhytskyi, V. V.; Ribalchenko, N. D.; Shramchenko, S. V.

2017-05-01

A comparative investigation of the metal of drums of two TP-100 boilers at the Starobeshevskaya and the Lugansk thermal power stations (TPS) was performed. Their operation time was approximately 300000 hours; the shell of one drum was ruptured during a hydraulic test, and the other drum is in operation. According to the results of the technical diagnostics and a strength analysis, both drums comply with the applicable regulatory requirements. The objects of the investigation were fragments of the ruptured drum and a "plug" cut out of the shell during a scheduled inspection. The investigation was carried out by microscopic metallography methods and the scanning electron microscopy technique. Mechanical tests of metal specimens were performed, and the hydrogen content in these specimens was measured. Prior to the material research, the metal was examined using a magnetic memory method. The investigation yielded specifics of the metal microstructure, mechanical properties, and fracture patterns of the metal specimens at various temperatures. An investigation performed by the method of thermal-desorption mass spectrometry revealed no considerable difference in the hydrogen content in the metal of both drums, thereby excluding the effect of hydrogenation in analyzing the rupture causes. It was established that the drum at the Starobeshevskaya TPS had been damaged due to its low impact strength at room temperature and high brittle-ductile transition point. Comparison of the metallographic study data with the results obtained using the magnetic memory method suggests that the fracture was caused by local formation of the Widmannstatten pattern at points where accessories are welded to the shell. The prospects are demonstrated of the comprehensive approach to nondestructive examination (NDE) of TPS drums using the magnetic memory technique and metallographic methods.

Investigations with respect to pressure build-up in 200 l drums with supercompacted low level waste (LLW)

International Nuclear Information System (INIS)

Kroth, K.; Lammertz, H.

1988-04-01

In the drum storage facilities of various nuclear power stations, ballooning effects have recently been observed on a limited number of 200 l drums filled with hypercompacted mixed LLW. The ballooning of the drums lid and bottom is due to internal overpressure caused by gas formation in the waste. The internal drum pressures and the composition of the drum gases were measured on a considerable number of 200 l drums. Hydrogen, formed by chemical reactions between the waste components, was identified as the pressure generating gas. The reasons for the hydrogen formation were investigated on both real and simulated wastes. (orig.) [de

Mushroom dehydration in a hybrid-solar dryer

International Nuclear Information System (INIS)

Reyes, Alejandro; Mahn, Andrea; Cubillos, Francisco; Huenulaf, Pedro

2013-01-01

Highlights: ► Mushrooms (Paris variety) were dehydrated in a hybrid solar dryer. ► Effective diffusivity was estimated by the Constant Diffusivity Model. ► Drying kinetics were adjusted by a semi-theoretical and the empirical Page model. ► Temperature, thickness and air recycle significantly affected critical moisture. ► The input of solar energy resulted in 3.5–12.5% electrical energy saving. - Abstract: Mushrooms (Paris variety) were dehydrated in a hybrid solar dryer (HSD) provided with a 3 m 2 solar panel and electric resistances. Mushrooms were cut in 8 mm or 4 mm thickness slices. At the outlet of the tray dryer 80–90% air was recycled and the air temperature was adjusted to the pre-defined levels (50 or 60 °C). At the outlet of the solar panel the air temperature raised between 2 and 20 °C above the ambient temperature, depending mainly of solar radiation level. Temperature, slices thickness and air recycle level had statistically significant effects on critical moisture content (X c ), as well as on the time necessary to reach a moisture content of 0.1 (wb). The color parameters of dehydrated mushroom indicate a notorious darkening, in all runs. Rehydration assays at 35 °C showed that in less than 30 min rehydrated mushrooms reached a moisture content of 0.8 (wb). Effective diffusivity (D eff ) was estimated by the Simplified Constant Diffusivity Model (SCDM), and it ranged between 6E−10 and 40E−10 m 2 /s, with R 2 higher than 0.98, agreeing with literature. The adjustment of experimental drying kinetics with the empirical Page’s model resulted in R 2 higher than 0.997. Finally, the input of solar energy resulted in 3.5–12.5% energy saving. These values could even be improved by increasing the agro-product load in the HSD

Predation of the zebra mussel (Dreissena polymorpha) by freshwater drum in western Lake Erie

Science.gov (United States)

French, John R. P.; Bur, Michael T.; Nalepa, Thomas F.; Schloesser, Donald W.

1992-01-01

Environmental and economic problems associated with the colonization of zebra mussels (Dreissena polymorpha) in western Lake Erie created a need to investigate control mechanisms. Predation by fishes is one potential means of control, but predation on zebra mussels by native fishes in Lake Erie is unknown. The freshwater drum (Aplodinotus grunniens) is the most likely fish predator since it is the only fish with pharyngeal teeth capable of crushing mollusk shells. In 1990, freshwater drum were collected in western Lake Erie from 9 sites near rocky reefs and 13 sites with silt or sand bottoms, and gut contents were examined. Predation on zebra mussels increased as drum size increased. Small drum (200-249 mm in length) fed mainly on dipterans, amphipods, and small fish; small zebra mussels (375 mm in length) fed almost exclusively on zebra mussels (seasons and locations combined). The smallest drum capable of crushing zebra mussel shells was 265 mm. Since freshwater drum over 375 mm feed heavily on zebra mussels, they may become a possible biological control mechanism for mussels in portions of North America.

Burning test on a storage drum filled with a mixture of sodiumnitrate and bitumen

International Nuclear Information System (INIS)

Knotik, K.; Leichter, P.; Spalek, K.

1979-01-01

A burning test on a common storage drum filled with a mixture of sodiumnitrate and bitumen was carried out to show the incinerability of said mixture. A 50 l mild steel drum was filled with 80,7 kg sodiumnitrate/bitumen-mixture. The drum was packed in a 200 l mild steel drum, the remaining space was filled with enough sand to cover the top of the inner drum with 15 cm of sand. The sand packing was then soaked with 70 l of light distillate fuel and ignited. The fuel burned until self-extinguishing occurred. 30 % (22,2 l) of the fuel was burned. 0,7 % of the energy potential was absorbed in the sand layer. The highest measured temperature was 34 0 C at the top of the test drum. It can be concluded, that even under severe external actions the ignition temperature of 400 0 C for bitumen/waste mixtures cannot be reached, providing correct technical storage conditions, which means that the void space in the cavities is filled with unburnable absorbing material like sand or salt. (author)

Sampling and analysis plan for the characterization of eight drums at the 200-BP-5 pump-and-treat systems

International Nuclear Information System (INIS)

Laws, J.R.

1995-01-01

Samples will be collected and analyzed to provide sufficient information for characterization of mercury and aluminum contamination in drums from the final rinse of the tanks in the two pump-and-treat systems supporting the 200-BP-5 Operable Unit. The data will be used to determine the type of contamination in the drums to properly designate the waste for disposal or treatment. This sampling plan does not substitute the sampling requirements but is a separate sampling event to manage eight drums containing waste generated during an unanticipated contamination of the process water with mercury and aluminum nitrate nonahydrate (ANN). The Toxicity Characteristic Leaching Procedure (TCLP) will be used for extraction, and standard US Environmental Protection Agency (EPA) methods will be used for analysis

Design, construction and test run of a two-tonne capacity solar rice dryer with rice-husk-fired auxiliary heater

International Nuclear Information System (INIS)

Iloeje, O.C.; Ekechukwu, O.V.; Ezeike, G.O.I.

1993-09-01

The design and construction details of a two-tonne per batch capacity natural-circulation solar rice dryer and the highlights of the design of its rice-husk-fired auxiliary heating system which is still under construction are presented. The dryer measures approximately 17.7m long by 9.8m wide by 6m high. Preliminary results of a test run on the solar dryer section only is reported. (author). 5 refs, 3 figs

The media, the reconstruction of drumming, and the tradition of the ...

African Journals Online (AJOL)

The Prodigal Ones by Mount Zion Films Production (and other drum music performance in films) shows the media enhancement of the performance of the ensemble serving as accompaniment during a traditional festival. The short scene allocated to a traditional festival reveals the significance of drumming and the input of ...

Identification of the fast and thermal neutron characteristics of transuranic waste drums

Energy Technology Data Exchange (ETDEWEB)

Storm, B.H. Jr.; Bramblett, R.L. [Lockheed Martin Specialty Components, Largo, FL (United States); Hensley, C. [Oak Ridge National Lab., TN (United States)

1997-11-01

Fissile and spontaneously fissioning material in transuranic waste drums can be most sensitively assayed using an active and passive neutron assay system such as the Active Passive Neutron Examination and Assay. Both the active and the passive assays are distorted by the presence of the waste matrix and containerization. For accurate assaying, this distortion must be characterized and accounted for. An External Matrix Probe technique has been developed that accomplishes this task. Correlations between in-drum neutron flux measurements and monitors in the Active Passive Neutron Examination and Assay chamber with various matrix materials provide a non-invasive means of predicting the thermal neutron flux in waste drums. Similarly, measures of the transmission of fast neutrons emitted from sources in the drum. Results obtained using the Lockheed Martin Specialty Components Active Passive Neutron Examination and Assay system are discussed. 12 figs., 1 tab.

The Extraordinary Nature of Barney's Drumming : A Complementary Study of Ordinary Noise Making in Chimpanzees

NARCIS (Netherlands)

Dufour, Valérie; Pasquaretta, Cristian; Gayet, Pierre; Sterck, Elisabeth H M

In a previous study (Dufour et al., 2015) we reported the unusual characteristics of the drumming performance of a chimpanzee named Barney. His sound production, several sequences of repeated drumming on an up-turned plastic barrel, shared features typical for human musical drumming: it was

Development of a multi-purpose dryer | Kadurumba | Nigeria ...

African Journals Online (AJOL)

The novel design uses heat sources from electric burners and it is located beneath the product spreading chamber. This prevented the problem of discoloration due to direct heat from the burners. A thermostat was used for its temperature control and light indicators were introduced to monitor the operation of the dryer with a ...

Coke drums inspection and evaluation using stress and strain analysis techniques

Energy Technology Data Exchange (ETDEWEB)

Haraguchi, Marcio Issamu [Tricom Tecnologia e Servicos de Manutencao Industrial Ltda., Piquete, SP (Brazil); Samman, Mahmod [Houston Engineering Solutions, Houston, TX (United States); Tinoco, Ediberto Bastos; Marangone, Fabio de Castro; Silva, Hezio Rosa da; Barcelos, Gustavo de Carvalho [Petroleo Brasileiro S.A. (PETROBRAS), Rio de Janeiro, RJ (Brazil)

2012-07-01

Coke drums deform due to a complex combination of mechanical and thermal cyclic stresses. Bulges have progressive behavior and represent the main maintenance problem related to these drums. Bulge failure typically result in through-wall cracks, leaks, and sometimes fires. Such failures generally do not represent a great risk to personnel. Repairs needed to maintain reliability of these vessels might require extensive interruption to operation which in turn considerably impacts the profitability of the unit. Therefore the condition, progression and severity of these bulges should be closely monitored. Coke drums can be inspected during turnaround with 3D Laser Scanning and Remote Visual Inspection (RVI) tools, resulting in a detailed dimensional and visual evaluation of the internal surface. A typical project has some goals: inspect the equipment to generate maintenance or inspection recommendations, comparison with previous results and baseline data. Until recently, coke drum structural analysis has been traditionally performed analyzing Stress Concentration Factors (SCF) thought Finite Element Analysis methods; however this technique has some serious technical and practical limitations. To avoid these shortcomings, the new strain analysis technique PSI (Plastic Strain Index) was developed. This method which is based on API 579/ ASME FFS standard failure limit represents the state of the art of coke drum bulging severity assessment has an excellent correlation with failure history. (author)

Analytical and empirical evaluation of low-level waste drum response to accident environments

International Nuclear Information System (INIS)

May, R.A.; Romesberg, L.E.; Yoshimura, H.R.; Baker, W.E.; Hokanson, J.C.

1980-01-01

Based on results of tests to date, it was found that the structural response of low-level waste drums to impact environments can be generally predicted, both analytically and with subscale models. As currently represented, only the 1/4 scale models would adequately represent full scale drum deformation; however, additional work has shown that with proper heat treating the strength of the material used in the 1/8 scale containers can be reduced to the correct value. Both analytical models give results that are expected to be within the range of behavior of the full scale drums. Failure of the drum closure can be adequately inferred from the radial deformation results of both subscale tests and computer analyses. 6 figures

Teknik Gelatinisasi Tepung Beras untuk Menurunkan Penyerapan Minyak Selama Penggorengan Minyak Terendam

Directory of Open Access Journals (Sweden)

Florentina Florentina

2017-02-01

Full Text Available Pregelatinized rice flour is one of ingredients that can reduce oil uptake. Gelatinization can be processed by drum drying, extrusion, and steaming. The aim of this research was to know the effect of gelatinization rice flour by drum drying, extrusion, and cooking rice on water holding capacity, degree of gelatinization, and oil uptake. Oil uptake was analyzed by using food model that substituted with 50 % pregelatinized flour. Results indicated that degree of gelatinization and water holding capacity of pregelatinized flour by drum drying was higher than extrusion and cooking rice. The highest reducing oil uptake of product was produced using pregelatinized flour by drum dryer was 33.70 % while by extruder which was 13.32 % and rice cooker was 10.09 % ABSTRAK Tepung beras pragelatinisasi merupakan salah satu ingredien yang dapat mengurangi penyerapan minyak. Proses gelatinisasi dapat dilakukan dengan metode pengeringan drum, ekstrusi, dan pengukusan. Penelitian ini bertujuan untuk mengetahui pengaruh teknik gelatinisasi tepung beras dengan pengeringan drum, ekstrusi, dan pemasakan nasi terhadap daya ikat air, derajat gelatinisasi dan penyerapan minyak. Penyerapan minyak dianalisis dengan menggunakan model pangan yang telah disubtitusi 50 % tepung pragelatinisasi. Hasil penelitian menunjukkan bahwa derajat gelatinisasi dan daya ikat air pada tepung pragelatinisasi dari pengeringan drum lebih tinggi daripada proses ekstrusi dan pemasakan nasi. Penurunan penyerapan minyak tertinggi dihasilkan pada produk dengan penggunaan tepung pragelatinisasi pengeringan drum yaitu 33,70 %, sedangkan ekstruder sebesar 13,32 % dan pemasak nasi sebesar 10,09 %.

Beat my bass, pluck my drum

NARCIS (Netherlands)

Hengeveld, B.J.; Funk, M.; Doing, V.

2014-01-01

Beating a bass, plucking a drum -- new systems of instruments make it possible. In this paper we describe recent research into networked musical instruments for group improvisation; instruments that reciprocally influence each other's behaviour, making, contrary to what we are used to, the

Corrosion of steel drums containing simulated radioactive waste of low and intermediate level

International Nuclear Information System (INIS)

Farina, S.B.; Schulz Rodríguez, F.; Duffó, G.S.

2013-01-01

Ion-exchange resins are frequently used during the operation of nuclear power plants and constitute radioactive waste of low and intermediate level. For the final disposal inside the repository the resins are immobilized by cementation and placed inside steel drums. The eventful contamination of the resins with aggressive species may cause corrosion problems to the drums. In order to assess the incidence of this phenomenon and to estimate the lifespan of the steel drums, in the present work, the corrosion susceptibility of steel drums in contact with cemented ion-exchange resins contaminated with different aggressive species was studied. The aggressive species studied were chloride ions (main ionic species of concern) and sulphate ions (produced during radiolysis of the cationic exchange-resins after cementation). The corrosion rate of the steel was monitored over a time period of 900 days and a chemical and morphological analysis of the corrosion products formed on the steel in each condition was performed. When applying the results obtained in the present work to estimate the corrosion depth of the drums containing the cemented radioactive waste after a period of 300 years (foreseen durability of the Low and Intermediate Level Radioactive Waste facility in Argentina), it was found that in the most unfavourable case (high chloride contamination), the corrosion penetration will be considerably lower than the thickness of the wall of the steel drums. (author)

Calculation of calibration factors and layout criteria for gamma scanning of waste drums from nuclear plants

International Nuclear Information System (INIS)

Inder Schmitten, W.; Sohnius, B.; Wehner, E.

1990-01-01

This paper present a procedure to calculate calibration factors for converting the measured gamma rate of waste drums into activity content and a layout and free release measurement criterion for waste drums. A computer program is developed that simulates drum scanning technique, which calculates calibration factors and eliminates laborious experimental measurements. The calculated calibration factors exhibit good agreement with experimentally determined values. By checking the calculated calibration factors for trial equipment layouts (including the waste drum and the scanning facility) using the layout and free release measurement criterion, a layout can be achieved that clearly determines whether there can be free release of a waste drum

A large-scale solar greenhouse dryer using polycarbonate cover: Modeling and testing in a tropical environment of Lao People's Democratic Republic

Energy Technology Data Exchange (ETDEWEB)

Janjai, Serm; Intawee, Poolsak; Kaewkiew, Jinda; Sritus, Chanoke [Solar Energy Research Laboratory, Department of Physics, Faculty of Science, Silpakorn University, Nakhon Pathom 73000 (Thailand); Khamvongsa, Vathsana [Department of Physics, Faculty of Natural Science, National University of Laos, P O Box 7322, Vientiane (Lao People' s Democratic Republic)

2011-03-15

A large-scale solar greenhouse dryer with a loading capacity of 1000 kg of fruits or vegetables has been developed and tested at field levels. The dryer has a parabolic shape and the dryer is covered with polycarbonate sheets. The base of the dryer is a black concrete floor with an area of 7.5 x 20.0 m{sup 2}. Nine DC fans powered by three 50-W solar cell modules are used to ventilate the dryer. The dryer was installed at Champasak (15.13 N, 105.79 E) in Lao People's Democratic Republic (Lao PDR). It is routinely used to dry chilli, banana and coffee. To assess the experimental performances of the dryer, air temperature, air relative humidity and product moisture contents were measured. One thousand kilograms of banana with the initial moisture content of 68% (wb) was dried within 5 days, compared to 7 days required for natural sun drying with the same weather conditions. Also three hundred kilograms of chilli with the initial moisture content of 75% (wb) was dried within 3 days while the natural sun drying needed 5 days. Two hundred kilograms of coffee with the initial moisture content of 52% (wb) was dried within 2 days as compared to 4 days required for natural sun drying. The chilli, coffee and banana dried in this dryer were completely protected from insects, animals and rain. Furthermore, good quality of dried products was obtained. The payback period of the dryer is estimated to be 2.5 years. A system of partial differential equations describing heat and moisture transfer during drying of chilli, coffee and banana in the greenhouse dryer was developed. These equations were solved by using the finite different method. The simulated results agree well with the experimental data. This model can be used to provide the design data for this type of dryer in other locations. (author)

Color image digitization and analysis for drum inspection

International Nuclear Information System (INIS)

Muller, R.C.; Armstrong, G.A.; Burks, B.L.; Kress, R.L.; Heckendorn, F.M.; Ward, C.R.

1993-01-01

A rust inspection system that uses color analysis to find rust spots on drums has been developed. The system is composed of high-resolution color video equipment that permits the inspection of rust spots on the order of 0.25 cm (0.1-in.) in diameter. Because of the modular nature of the system design, the use of open systems software (X11, etc.), the inspection system can be easily integrated into other environmental restoration and waste management programs. The inspection system represents an excellent platform for the integration of other color inspection and color image processing algorithms

Equipment for capping drums, especially with radioactive waste

International Nuclear Information System (INIS)

Bednarik, F.

1987-01-01

The equipment consists of a pneumatic cylinder, lever systems with jaws, guide bars, and of securing pins. The top cylinder lid and the bottom cylinder lid provided with openings are slidably attached to a shaft firmly connected to a piston and a support plate. Firmly attached to the bottom lid using brackets are pins holding connecting rods controlling the double-arm levers pivoted on pins, featuring jaws pivoted on forks firmly attached to the support plate and provided with a replaceable spacer insert. The guide bars are firmly attached to the support plate via braces and stiffeners. The securing pins are loaded with springs seated in the braces. The benefits of the equipment include that the lid closing levers with jaws, mechanically controlled using one pneumatic cylinder, thanks to their number and configuration, close the lid around the drum border provided with small recesses which do not reach above the circumference of the drum being closed. The equipment can also be used for carrying closed drums, this also during compressed air failures because the levers with jaws are secured in position with the pneumatic cylinder leg. (J.B.). 1 fig

A-Ha. Drum'n'bassi supernimi FABIO

Index Scriptorium Estoniae

2002-01-01

7.sept. annab norra menukaim popansambel A-Ha Tallinnas Lauluväljakul kontserdi, kus presenteerib ka oma viimast albumit "Lifelines". 14. sept.tuleb drum'n'bassi spetsialist Fabio Tallinna üritusele Circulation

Thermal decomposition study of uranyl nitrate and cerium hydroxide in a spray dryer

International Nuclear Information System (INIS)

Silva Wildhagen, G.R. da.

1993-05-01

A study, in a spray dryer system based on drying and thermal decomposition of uranyl nitrate solutions aiming the production of uranium trioxide adequate for the use in posterior steps of reduction and hydro fluorination in nuclear fuel cycle; and cerium hydroxide suspensions for the production of cerium oxide with high surface area is presented. Thus, the project and construction of a countercurrent spray dryer was elaborated for capacity of 10 Kg U O 3 /h and 3,5 k Ce O 2 /h. The methodology used in these experiments consisted in the analysis of several parameters (concentration and flow rate of the feed, atomization pressure and inlet temperature of the dryer) over the physical and chemical properties of the products. Using the obtained results, with the help of a mathematical model, it was developed the project of a continuous pilot unity for the production of uranium trioxide or cerium oxide, with capacity of 20 Kg U O 3 /h or 10 Kg Ce O 2 /h, respectively. (author)

A solar assisted heat-pump dryer and water heater

International Nuclear Information System (INIS)

Hawlader, M.N.A.; Chou, S.K.; Jahangeer, K.A.; Rahman, S.M.A.

2006-01-01

Growing concern about the depletion of conventional energy resources has provided impetus for considerable research and development in the area of alternative energy sources. A solar assisted heat pump dryer and water heater found to be one of the solutions while exploring for alternative energy sources. The heat pump system is used for drying and water heating applications with the major share of the energy derived from the sun and the ambient. The solar assisted heat pump dryer and water heater has been designed, fabricated and tested. The performance of the system has been investigated under the meteorological conditions of Singapore. The system consists of a variable speed reciprocating compressor, evaporator-collector, storage tank, air cooled condenser, auxiliary heater, blower, dryer, dehumidifier, and air collector. The drying medium used is air and the drying chamber is configured to carry out batch drying of good grains. A water tank connected in series with the air cooled condenser delivers hot water for domestic applications. The water tank also ensures complete condensation of the refrigerant vapour. A simulation program is developed using Fortran language to evaluate the performance of the system and the influence of different variables. The performance indices considered to evaluate the performance of the system are: Solar Fraction (SF), Coefficient of Performance (COP) and Specific Moisture Extraction Rate (SMER). A COP value of 7.5 for a compressor speed of 1800 rpm was observed. Maximum collector efficiencies of 0.86 and 0.81 have been found for evaporator-collector and air collector, respectively. A value of the SMER of 0.79 has been obtained for a load of 20 kg and a compressor speed of 1200 rpm

Analysis, scale modeling, and full-scale tests of low-level nuclear-waste-drum response to accident environments

International Nuclear Information System (INIS)

Huerta, M.; Lamoreaux, G.H.; Romesberg, L.E.; Yoshimura, H.R.; Joseph, B.J.; May, R.A.

1983-01-01

This report describes extensive full-scale and scale-model testing of 55-gallon drums used for shipping low-level radioactive waste materials. The tests conducted include static crush, single-can impact tests, and side impact tests of eight stacked drums. Static crush forces were measured and crush energies calculated. The tests were performed in full-, quarter-, and eighth-scale with different types of waste materials. The full-scale drums were modeled with standard food product cans. The response of the containers is reported in terms of drum deformations and lid behavior. The results of the scale model tests are correlated to the results of the full-scale drums. Two computer techniques for calculating the response of drum stacks are presented. 83 figures, 9 tables

Method of and apparatus for decontaminating radioactive garments

International Nuclear Information System (INIS)

Capella, J.A.; Morrison, D.R.

1980-01-01

Garments are deposited in a cleaning drum which is agitated during a wash cycle. A dry cleaning solvent is continuously added to the drum during the wash cycle and continuously removed from the drum during the wash cycle to flush the radioactive particulate material separated from the garments into a sump. The solvent is pumped from the sump for addition to the drum during the wash cycle and the pumped solvent is filtered to remove substantially all of the radioactive particulate material suspended in the solvent. Radiation sensors permit monitoring of the recycled solvent to ensure satisfactory operation of filters. The solvent is cleaned by a distilling apparatus, a condenser and a moisture separating apparatus. A fan dryer is provided. (author)

X-Ray, Digital Imaging with Volumetric Density Measurement and Profiling, Applied to the Characterization of Waste Drums

International Nuclear Information System (INIS)

Huhtiniemi, I.; Gupta, N.; Halliwell, S.

2006-01-01

The European Commission's Joint Research Centre Ispra Site (JRC-Ispra) has initiated a decommissioning and waste management program that will span about two decades. The program includes a requirement to characterize the contents of about 6,500 radioactive, 220 litre waste drums whose documented history is incomplete. To render the characterization process more efficient, the drums will be initially divided into homogeneous groups, an activity that will be based on existing documentation and non-destructive examination (NDE) by X-ray digital imaging. This paper describes the X-ray imaging techniques chosen, and the planned performance validation of the equipment. (authors)

Behavior of a portable solar dryer for pineapple fiber Comportamento de um secador solar para fibras de abacaxi

Directory of Open Access Journals (Sweden)

Róger Moya

2012-12-01

Full Text Available In Costa Rica, there has been a growing interest to use pineapple fiber from plant, for which current processes need to be improved or new processes need to be developed, with emphasis on drying methods. This work presents the design and evaluation of the behavior of a prototype portable solar dryer in four sites of Costa Rica. The design describes the main parts of the dryer, as well as how they were constructed. The behavior was evaluated according to temperature and relative humidity inside e outside the chamber, and the influence of direct and indirect solar radiation. In order to achieve improved dryer efficiency, a dehumidifier was used to control relative humidity, and a heating system was implemented during the hours of low temperature, low solar radiation and high relative humidity. Based on drying time, final moisture content of fibers of pineapple leaves from plant, and the varying hours when fibers were put to dry, the evaluation of the dryer revealed that the best fiber-drying interval is from 6h00 to 14h00, and after that, it is convenient to inject hot air and use a dehumidifier in the dryer in order to increase its efficiency.Na Costa Rica, o interesse pelo uso da fibra proveniente da folha de abacaxizeiro. Tem almentado e essa atividade precisa de melhoramento ou implementação de novos processos para alcançar maior eficiência, principalmente na secagem da fibra. O presente trabalho apresenta o design e comportamento de uma protótipo portátil de secadora solar em 4 sites geográficos da Costa Rica. Estão descritas as principais partes do secador, bem como a metodologia de construção. O comportamento foi avaliado de acordo com a temperatura e umidade relativa interna e externa da câmara e a influencia da radiação direta e indireta. Com a finalidade de melhorar a eficiência da secadora, foi usado um desumidificador para controlar a umidade relativa e ainda um sistema de aquecimento durante as horas de baixa temperatura

Europa Drum Sampler (EDuS), Phase I

Data.gov (United States)

National Aeronautics and Space Administration — The main objective of the proposed work is to develop a robust and effective sample acquisition system for the Europa lander called the Europa Drum Sampler (EDuS)....

Energy Cost of Active and Sedentary Music Video Games: Drum and Handheld Gaming vs. Walking and Sitting.

Science.gov (United States)

Miranda, Edwin; Overstreet, Brittany S; Fountain, William A; Gutierrez, Vincent; Kolankowski, Michael; Overstreet, Matthew L; Sapp, Ryan M; Wolff, Christopher A; Mazzetti, Scott A

2017-01-01

To compare energy expenditure during and after active and handheld video game drumming compared to walking and sitting. Ten experienced, college-aged men performed four protocols (one per week): no-exercise seated control (CTRL), virtual drumming on a handheld gaming device (HANDHELD), active drumming on drum pads (DRUM), and walking on a treadmill at ~30% of VO 2max (WALK). Protocols were performed after an overnight fast, and expired air was collected continuously during (30min) and after (30min) exercise. DRUM and HANDHELD song lists, day of the week, and time of day were identical for each participant. Significant differences (p DRUM > HANDHELD. No significant differences in the rates of energy expenditure among groups during recovery were observed. Total energy expenditure was significantly greater (p < 0.05) during WALK (149.5 ± 30.6 kcal) compared to DRUM (118.7 ± 18.8 kcal) and HANDHELD (44.9±11.6 kcal), and greater during DRUM compared to HANDHELD. Total energy expenditure was not significantly different between HANDHELD (44.9 ± 11.6 kcal) and CTRL (38.2 ± 6.0 kcal). Active video game drumming at expert-level significantly increased energy expenditure compared to handheld, but it hardly met moderate-intensity activity standards, and energy expenditure was greatest during walking. Energy expenditure with handheld video game drumming was not different from no-exercise control. Thus, traditional aerobic exercise remains at the forefront for achieving the minimum amount and intensity of physical activity for health, individuals desiring to use video games for achieving weekly physical activity recommendations should choose games that require significant involvement of lower-body musculature, and time spent playing sedentary games should be a limited part of an active lifestyle.

MCNP Modeling Results for Location of Buried TRU Waste Drums

International Nuclear Information System (INIS)

Steinman, D K; Schweitzer, J S

2006-01-01

In the 1960's, fifty-five gallon drums of TRU waste were buried in shallow pits on remote U.S. Government facilities such as the Idaho National Engineering Laboratory (now split into the Idaho National Laboratory and the Idaho Completion Project [ICP]). Subsequently, it was decided to remove the drums and the material that was in them from the burial pits and send the material to the Waste Isolation Pilot Plant in New Mexico. Several technologies have been tried to locate the drums non-intrusively with enough precision to minimize the chance for material to be spread into the environment. One of these technologies is the placement of steel probe holes in the pits into which wireline logging probes can be lowered to measure properties and concentrations of material surrounding the probe holes for evidence of TRU material. There is also a concern that large quantities of volatile organic compounds (VOC) are also present that would contaminate the environment during removal. In 2001, the Idaho National Engineering and Environmental Laboratory (INEEL) built two pulsed neutron wireline logging tools to measure TRU and VOC around the probe holes. The tools are the Prompt Fission Neutron (PFN) and the Pulsed Neutron Gamma (PNG), respectively. They were tested experimentally in surrogate test holes in 2003. The work reported here estimates the performance of the tools using Monte-Carlo modelling prior to field deployment. A MCNP model was constructed by INEEL personnel. It was modified by the authors to assess the ability of the tools to predict quantitatively the position and concentration of TRU and VOC materials disposed around the probe holes. The model was used to simulate the tools scanning the probe holes vertically in five centimetre increments. A drum was included in the model that could be placed near the probe hole and at other locations out to forty-five centimetres from the probe-hole in five centimetre increments. Scans were performed with no chlorine in the

Press to compress contaminated wastes drums

International Nuclear Information System (INIS)

Prevost, J.

1993-01-01

This patent describes a press for contaminated wastes drums pressing. The press is made of a structure comprising a base and an upper stringer bind to the base by vertical bearers, a compression system comprising a main cylinder and a ram, connected to the upper stringer

Development of Simple Drying Model for Performance Prediction of Solar Dryer: Theoretical Analysis

DEFF Research Database (Denmark)

Singh, Shobhana; Kumar, Subodh

2012-01-01

An analytical moisture diffusion model which considers the influence of external resistance to mass transfer is developed to predict thermal performance of dryer system. The moisture diffusion coefficient, Deff that is necessary to evaluate the prediction model has been determined in terms...... of experimental drying parameters. A laboratory model of mixed-mode solar dryer system is tested with cylindrical potato samples of thickness 5 and 18 mm under simulated indoor conditions. The potato samples were dried at a constant absorbed thermal energy of 750 W/m2 and air mass flow rate of 0.011 kg...

A Markov chain analysis of the effectiveness of drum-buffer-rope material flow management in job shop environment

Directory of Open Access Journals (Sweden)

Masoud Rabbani

2015-09-01

Full Text Available The theory of constraints is an approach for production planning and control, which emphasizes on the constraints in the system to increase throughput. The theory of constraints is often referred to as Drum-Buffer-Rope developed originally by Goldratt. Drum-Buffer-Rope uses the drum or constraint to create a schedule based on the finite capacity of the first bottleneck. Because of complexity of the job shop environment, Drum-Buffer-Rope material flow management has very little attention to job shop environment. The objective of this paper is to apply the Drum-Buffer-Rope technique in the job shop environment using a Markov chain analysis to compare traditional method with Drum-Buffer-Rope. Four measurement parameters were considered and the result showed the advantage of Drum-Buffer-Rope approach compared with traditional one.

Application of the Monte Carlo method to estimate doses in a radioactive waste drum environment

International Nuclear Information System (INIS)

Rodenas, J.; Garcia, T.; Burgos, M.C.; Felipe, A.; Sanchez-Mayoral, M.L.

2002-01-01

During refuelling operation in a Nuclear Power Plant, filtration is used to remove non-soluble radionuclides contained in the water from reactor pool. Filter cartridges accumulate a high radioactivity, so that they are usually placed into a drum. When the operation ends up, the drum is filled with concrete and stored along with other drums containing radioactive wastes. Operators working in the refuelling plant near these radwaste drums can receive high dose rates. Therefore, it is convenient to estimate those doses to prevent risks in order to apply ALARA criterion for dose reduction to workers. The Monte Carlo method has been applied, using MCNP 4B code, to simulate the drum containing contaminated filters and estimate doses produced in the drum environment. In the paper, an analysis of the results obtained with the MCNP code has been performed. Thus, the influence on the evaluated doses of distance from drum and interposed shielding barriers has been studied. The source term has also been analysed to check the importance of the isotope composition. Two different geometric models have been considered in order to simplify calculations. Results have been compared with dose measurements in plant in order to validate the calculation procedure. This work has been developed at the Nuclear Engineering Department of the Polytechnic University of Valencia in collaboration with IBERINCO in the frame of an RD project sponsored by IBERINCO

Analysis of Energy Consumption of "Compression Heat" Pressure Heat Dryer%“压缩热”干燥机能耗分析

Institute of Scientific and Technical Information of China (English)

李申

2015-01-01

作为典型的热质交换设备，吸附干燥器再生能量是被吸水量锁定的。总耗能受到吸附剂本身物理性质的制约，可用“质量守恒”与“能量守恒”两大定律来解释其能耗过程。各类吸附干燥器能耗量都要通过“能量衡算”来确定。“压缩热”干燥器与其他一切加热干燥器一样采取了“长周期”工作循环制，解吸环节无效热损很大。无热再生干燥器则采用了“短周期”工作制，为实际耗气量减少留有了较大的空间。%As the typical heat and mass transfer equipment, the energy of regenerative desiccant dryers is limited by water absorption. The total energy consumption is restricted by the physical properties of the adsorbent, which can be explained through two laws of conservation of mass and energy conservation. The energy consumption in each absorption dryers should be determined by“energy balance”.“Compression heat”dryer adopts“long-period”working cycle system as other heating dryers, in which invalid heat losses are great in desorption process. However, regenerated dryer without heat adopts“short-period”working cycle system, which provides greater space for actual gas consumption reduction.

Performance analysis of greenhouse dryer by using insulated north-wall under natural convection mode

Directory of Open Access Journals (Sweden)

Prashant Singh Chauhan

2016-11-01

Full Text Available A prototype north wall insulated greenhouse dryer has been fabricated and tested in no-load conditions under natural convection mode. Experimentation has been conducted in two different cases. Case-I is when solar collector placed inside the dryer and Case-II is North wall insulated greenhouse dryer without solar collector. Coefficient of performance, heat utilisation factor, convective heat transfer coefficient and coefficient of diffusivity have been evaluated in thermal performance analysis. The difference of the highest convective heat transfer coefficient of both cases is 29.094W/m2°C which is showing the effectiveness of insulated north wall and solar collector. The maximum coefficient of diffusivity (0.0827 was achieved during the third day of experiment in Case-II. The inside room temperature of wall insulated greenhouse dryer for Case-I is 4.11%, 5.08 % and 11.61 % higher than the Case-II during the day 1, day 2 and day 3 respectively. This result is also showing the effectiveness of solar collector and insulated north wall. The highest heat utilisation factor (0.616 is obtained during the second day for Case-I while for Case-II it is 0.769 during the third day of experimentation. Maximum coefficient of performance achieved is 0.892 during the third day of the experiment for Case-I whereas 0.953 is obtained on the first day of experimentation for Case-II.

DRUMS: a human disease related unique gene mutation search engine.

Science.gov (United States)

Li, Zuofeng; Liu, Xingnan; Wen, Jingran; Xu, Ye; Zhao, Xin; Li, Xuan; Liu, Lei; Zhang, Xiaoyan

2011-10-01

With the completion of the human genome project and the development of new methods for gene variant detection, the integration of mutation data and its phenotypic consequences has become more important than ever. Among all available resources, locus-specific databases (LSDBs) curate one or more specific genes' mutation data along with high-quality phenotypes. Although some genotype-phenotype data from LSDB have been integrated into central databases little effort has been made to integrate all these data by a search engine approach. In this work, we have developed disease related unique gene mutation search engine (DRUMS), a search engine for human disease related unique gene mutation as a convenient tool for biologists or physicians to retrieve gene variant and related phenotype information. Gene variant and phenotype information were stored in a gene-centred relational database. Moreover, the relationships between mutations and diseases were indexed by the uniform resource identifier from LSDB, or another central database. By querying DRUMS, users can access the most popular mutation databases under one interface. DRUMS could be treated as a domain specific search engine. By using web crawling, indexing, and searching technologies, it provides a competitively efficient interface for searching and retrieving mutation data and their relationships to diseases. The present system is freely accessible at http://www.scbit.org/glif/new/drums/index.html. © 2011 Wiley-Liss, Inc.

Corrosion of steel drums containing immobilized ion exchange-resins and incineration ashes

International Nuclear Information System (INIS)

Marotta, F.; Schulz Rodriguez, F.M.; Farina, Silvia B.; Duffo, Gustavo S.

2009-01-01

The Argentine Atomic Energy Commission (CNEA) is responsible for developing the management nuclear waste disposal programme. This programme contemplates the design and construction of a facility for the final disposal of intermediate-level radioactive wastes. The proposed model is a near-surface monolithic repository similar to those in operation in El Cabril, Spain. The design of this type of repository is based on the use of multiple, independent and redundant barriers. The intermediate radioactive waste consists mostly in spent ionic exchange resins and filters from the nuclear power plants, research reactors and radioisotopes production facilities. The spent resins, as well as the incineration ashes, have to be immobilized before being stored to improve leach resistance of waste matrix and to maintain mechanical stability for safety requirements. Generally, cementation processes have been used as immobilization techniques for economical reasons as well as for being a simple operation. The immobilized resins and incineration ashes are thus contained in steel drums that, in turn, can undergo corrosion depending on the ionic content of the matrix. This work is a part of a systematic study of the corrosion susceptibility of steel drums in contact with immobilized cemented exchange-resins with different types and contents of aggressive species and incineration ashes. To this purpose, a special type of specimen was manufactured to simulate the cemented waste in the drum. The evolution of the corrosion potential and the corrosion current density of the steel, as well as the electrical resistivity of the matrix are being monitored along time. The aggressive species studied were chloride ions (the main ionic species present in nature) and sulphate ions (produced during the radiolysis process of the cationic exchange-resins after cementation). Preliminary results show the strong effect of chloride on the corrosion susceptibility of the steel. Monitoring will continue for

Electric-stepping-motor tests for a control-drum actuator of a nuclear reactor

Science.gov (United States)

Kieffer, A. W.

1972-01-01

Experimental tests were conducted on two stepping motors for application as reactor control-drum actuators. Various control-drum loads with frictional resistances ranging from approximately zero to 40 N-m and inertias ranging from zero to 0.424 kg-sq m were tested.

Evaluation of a fruit solar dryer; Avaliacao de um secador solar de frutas

Energy Technology Data Exchange (ETDEWEB)

Berthier, L.J.; Bittencourt, J.; Queiroz, M.R.

2000-07-01

A study of the Nanica banana drying was carried out in a solar dryer with six trays operating with direct exposure of the product to the solar radiation and internal convection. The solar drying was performed College of Agricultural Engineering of the UNICAMP, Campinas, S.Paulo state, Brazil. The study aimed a 20 to 25 per cent final humidity of the dry product, result obtained in the different trays during a maximum drying period of 147 hours (6 days), in a batch system. During the drying period, the average temperature of the environment air at daylight was of 26 degree Celsius with a maximum of 32 degree Celsius, and 18 degrees Celsius during nocturnal period, with a minimum of 12,6 degree Celsius. In the inward of the dryer reached average values near to 50 degree Celsius, measured at noon. The 29,540 kg initial net weight of peeled banana was reduced to yield of 10,815 kg after the drying process, obtaining an income of 36,61 percent of the total production. With the values of the product weight loss, the curves of the drying in each tray had been built, observing that, in the upper trays reached the desired humidity in a lesser period.

Steam generator with integral downdraft dryer. Final project report

Energy Technology Data Exchange (ETDEWEB)

Hochmuth, F.W.

1992-02-01

On June 30, 1989, a financial assistance award was granted by the United State Department of Energy, the purpose of which was to study and evaluate the technical aspect, the economic viability, and commercial possibilities of a new furnace design for burning high moisture cellulose type fuels. The new design is an invention by F.W. Hochmuth, P.Eng. and has received United States Patents Nos. 4,480, 557 and 4,502,397. It was conceived as a method to improve the general operation and efficiency of waste wood burning boilers, to avoid the use of stabilizing fuels such as oil or gas, and to reduce objectionable stack emissions. A further objective was to obtain such benefits at relatively low cost by integrating all new material requirements within the furnace itself thereby avoiding the need for costly external equipment. The proposed integral down-draft dryer avoids the use of external dryer systems that are very expensive, have high power consumption, and require a large amount of maintenance. This document provides the details of this invention.

First Industrial Tests of a Matrix Monitor Correction for the Differential Die-away Technique of Historical Waste Drums

International Nuclear Information System (INIS)

Antoni, Rodolphe; Passard, Christian; Perot, Bertrand; Batifol, Marc; Vandamme, Jean-Christophe; Grassi, Gabriele

2015-01-01

The fissile mass in radioactive waste drums filled with compacted metallic residues (spent fuel hulls and nozzles) produced at AREVA NC La Hague reprocessing plant is measured by neutron interrogation with the Differential Die-away measurement Technique (DDT). In the next years, old hulls and nozzles mixed with Ion-Exchange Resins will be measured. The ion-exchange resins increase neutron moderation in the matrix, compared to the waste measured in the current process. In this context, the Nuclear Measurement Laboratory (LMN) of CEA Cadarache has studied a matrix effect correction method, based on a drum monitor, namely a 3He proportional counter located inside the measurement cavity. After feasibility studies performed with LMN's PROMETHEE 6 laboratory measurement cell and with MCNPX simulations, this paper presents first experimental tests performed on the industrial ACC (hulls and nozzles compaction facility) measurement system. A calculation vs. experiment benchmark has been carried out by performing dedicated calibration measurements with a representative drum and 235 U samples. The comparison between calculation and experiment shows a satisfactory agreement for the drum monitor. The final objective of this work is to confirm the reliability of the modeling approach and the industrial feasibility of the method, which will be implemented on the industrial station for the measurement of historical wastes. (authors)

Performance of a convective, infrared and combined infrared- convective heated conveyor-belt dryer.

Science.gov (United States)

El-Mesery, Hany S; Mwithiga, Gikuru

2015-05-01

A conveyor-belt dryer was developed using a combined infrared and hot air heating system that can be used in the drying of fruits and vegetables. The drying system having two chambers was fitted with infrared radiation heaters and through-flow hot air was provided from a convective heating system. The system was designed to operate under either infrared radiation and cold air (IR-CA) settings of 2000 W/m(2) with forced ambient air at 30 °C and air flow of 0.6 m/s or combined infrared and hot air convection (IR-HA) dryer setting with infrared intensity set at 2000 W/m(2) and hot at 60 °C being blown through the dryer at a velocity of 0.6 m/s or hot air convection (HA) at an air temperature of 60 °C and air flow velocity 0.6 m/s but without infrared heating. Apple slices dried under the different dryer settings were evaluated for quality and energy requirements. It was found that drying of apple (Golden Delicious) slices took place in the falling rate drying period and no constant rate period of drying was observed under any of the test conditions. The IR-HA setting was 57.5 and 39.1 % faster than IR-CA and HA setting, respectively. Specific energy consumption was lower and thermal efficiency was higher for the IR-HA setting when compared to both IR-CA and HA settings. The rehydration ratio, shrinkage and colour properties of apples dried under IR-HA conditions were better than for either IR-CA or HA.

Detection of free liquid in cement-solidified radioactive waste drums using computed tomography

International Nuclear Information System (INIS)

Steude, J.S.; Tonner, P.D.

1991-01-01

Acceptance criteria for disposal of radioactive waste drums require that the cement-solidified material in the drum contain minimal free liquid after the cement has hardened. Free liquid is to be avoided because it may corrode the drum, escape and cause environmental contamination. The DOE has requested that a nondestructive evaluation method be developed to detect free liquid in quantities in excess of 0.5% by volume. This corresponds to about 1 liter in a standard 208 liter (55 gallon) drum. In this study, the detection of volumes of free liquid in a 57 cm (2 ft.) diameter cement-solidified drum is demonstrated using high-energy X-ray computed tomography (CT0. In this paper it is shown that liquid concentrations of simulated radioactive waste inside glass tubes imbedded in cement can easily be detected, even for tubes with inner diameters less than 2 mm (0.08 in.). Furthermore, it is demonstrated that tubes containing water and liquid concentrations of simulated radioactive waste can be distinguished from tubes of the same size containing air. The CT images were obtained at a rate of about 6 minutes per slice on a commercially available CT system using a 9 MeV linear accelerator source

Temperature Control System for Mushroom Dryer

Science.gov (United States)

Wibowo, I. A.; Indah, Nur; Sebayang, D.; Adam, N. H.

2018-03-01

The main problem in mushroom cultivation is the handling after the harvest. Drying is one technique to preserve the mushrooms. Traditionally, mushrooms are dried by sunshine which depends on the weather. This affects the quality of the dried mushrooms. Therefore, this paper proposes a system to provide an artificial drying for mushrooms in order to maintain their quality. The objective of the system is to control the mushroom drying process to be faster compared to the natural drying at an accurate and right temperature. A model of the mushroom dryer has been designed, built, and tested. The system comprises a chamber, heater, blower, temperature sensor and electronic control circuit. A microcontroller is used as the controller which is programmed to implement a bang-bang control that regulates the temperature of the chamber. A desired temperature is inputted as a set point of the control system. Temperature of 45 °C is chosen as the operational drying temperature. Several tests have been carried out to examine the performance of the system including drying speed, the effects of ambient conditions, and the effects of mushroom size. The results show that the system can satisfy the objective.

Nuclear waste calorimeter for very large drums with 385 litres sample volume

Energy Technology Data Exchange (ETDEWEB)

Jossens, G.; Mathonat, C. [SETARAM Instrumentation, Caluire (France); Bachelet, F. [CEA Valduc, Is sur Tille (France)

2015-03-15

Calorimetry is a very precise and well adapted tool for the classification of drums containing nuclear waste material depending on their level of activities (low, medium, high). A new calorimeter has been developed by SETARAM Instrumentation and the CEA Valduc in France. This new calorimeter is designed for drums having a volume bigger than 100 liters. It guarantees high operator safety by optimizing drum handling and air circulation for cooling, and optimized software for direct measurement of the quantity of nuclear material. The LVC1380 calorimeter makes it possible to work over the range 10 to 3000 mW, which corresponds to approximately 0.03 to 10 g of tritium or 3 to 955 g of {sup 241}Pu in a volume up to 385 liters. This calorimeter is based on the heat flow measurement using Peltier elements which surround the drum in the 3 dimensions and therefore measure all the heat coming from the radioactive stuff whatever its position inside the drum. Calorimeter's insulating layers constitute a thermal barrier designed to filter disturbances until they represent less than 0.001 Celsius degrees and to eliminate long term disturbances associated, for example, with laboratory temperature variations between day and night. A calibration device based on Joule effect has also been designed. Measurement time has been optimized but remains long compared with other methods of measurement such as gamma spectrometry but its main asset is to have a good accuracy for low level activities.

Radioactive gaseous waste processing device

International Nuclear Information System (INIS)

Kishi, Tadao.

1990-01-01

The present invention concerns a radioactive gaseous waste processing device used in BWR power plants. A heater is disposed to the lower portion of a dryer for dehydrating radioactive off gases. Further, a thermometer is disposed to a coolant return pipeway on the exit side of the cooling portion of the dryer and signals sent from the thermometer are inputted to an automatic temperature controller. If the load on the dryer is reduced, the value of the thermometer is lowered than a set value, then an output signal corresponding to the change is supplied from the automatic temperature controller to the heater to forcively apply loads to the dryer. Therefore, defrosting can be conducted completely without operating a refrigerator, and the refrigerator can be maintained under a constant load by applying a dummy load when the load in the dryer is reduced. (I.N.)

Real-time radiography, digital radiography, and computed tomography for nonintrusive waste drum characterization

International Nuclear Information System (INIS)

Martz, H.E.; Schneberk, D.J.; Roberson, G.P.

1994-07-01

We are investigating and developing the application of x-ray nondestructive evaluation (NDE) and gamma-ray nondestructive assay (NDA) methods to nonintrusively characterize 208-liter (55-gallon) mixed waste drums. Mixed wastes contain both hazardous and radioactive materials. We are investigating the use of x-ray NDE methods to verify the content of documented waste drums and determine if they can be used to identify hazardous and nonconforming materials. These NDE methods are also being used to help waste certification and hazardous waste management personnel at LLNL to verify/confirm and/or determine the contents of waste. The gamma-ray NDA method is used to identify the intrinsic radioactive source(s) and to accurately quantify its strength. The NDA method may also be able to identify some hazardous materials such as heavy metals. Also, we are exploring techniques to combine both NDE and NDA data sets to yield the maximum information from these nonintrusive, waste-drum characterization methods. In this paper, we report an our x-ray NDE R ampersand D activities, while our gamma-ray NDA activities are reported elsewhere in the proceedings. We have developed a data, acquisition scanner for x-ray NDE real-time radiography (RTR), as well as digital radiography transmission computed tomography (TCT) along with associated computational techniques for image reconstruction, analysis, and display. We are using this scanner and real-waste drums at Lawrence Livermore National Laboratory (LLNL). In this paper, we discuss some issues associated with x-ray imaging, describe the design construction of an inexpensive NDE drum scanner, provide representative DR and TCT results of both mock- and real-waste drums, and end with a summary of our efforts and future directions. The results of these scans reveal that RTR, DR, and CT imaging techniques can be used in concert to provide valuable information about the interior of low-level-, transuranic-, and mock-waste drums without

Comparison of three control strategies for optimization of spray dryer operation

DEFF Research Database (Denmark)

Petersen, Lars Norbert; Poulsen, Niels Kjølstad; Niemann, Hans Henrik

2017-01-01

controllers for operation of a four-stage spray dryer. The three controllers are a proportional-integral (PI) controller that is used in industrial practice for spray dryer operation, a linear model predictive controller with real-time optimization (MPC with RTO, MPC-RTO), and an economically optimizing...... nonlinear model predictive controller (E-NMPC). The MPC with RTO is based on the same linear state space model in the MPC and the RTO layer. The E-NMPC consists of a single optimization layer that uses a nonlinear system of ordinary differential equations for its predictions. The PI control strategy has...... the production rate, while minimizing the energy consumption, keeping the residual moisture content of the powder below a maximum limit, and avoiding that the powder sticks to the chamber walls. We use an industrially recorded disturbance scenario in order to produce realistic simulations and conclusions...

The Effect of Wetting on The Course of The Drum Granulation

Directory of Open Access Journals (Sweden)

Błaszczyk Michał

2017-06-01

Full Text Available This paper presents the results of experimental drum granulation of silica flour with the use of wetting liquids with different values of surface tension. Additionally, different liquid jet breakup and different residual moisture of the bed were applied in the tests. The process was conducted periodically in two stages: wetting and proper granulation, during which no liquid was supplied to the bed. The condition of the granulated material after the period of wetting (particle size distribution and moisture of separate fractions and a change in the particle size distribution during the further conduct of the process (granulation kinetics were determined.

Case studies of heat conduction in rotary drums with L-shaped lifters via DEM

Directory of Open Access Journals (Sweden)

Qiang Xie

2018-03-01

Full Text Available Rotary drums are widely used in numerous processes in industry to handle granular materials. In present work, heat transfer processes in drums with L-shaped lifters have been investigated by coupling the discrete element method (DEM with heat transfer model. Effects of both operational and structural parameters have been analyzed. It is found that increasing rotational speed could improve heat transfer to a certain extent, however, just in relatively low speed stage. When lifter number increases, the heat transfer speed slightly decreases. An increasing lifter height could promote heat transfer first and then reduces it, but the amplitude of variation keeps small. The heat transfer rate descends with increasing lifter width. The heat transfer mechanisms have also been discussed by comparing mixing rates, total contact areas for thermal conduction, time constants (TC indicating apparent heat transfer rate and effective heat transfer coefficients(HTC. It is concluded that dynamic conduction due to particle flow is dominated in all cases. The L-shaped lifers are turned out not a good choice when heat conduction between particles is prominent.

Simulation of Solar Heat Pump Dryer Directly Driven by Photovoltaic Panels

Science.gov (United States)

Houhou, H.; Yuan, W.; Wang, G.

2017-05-01

This paper investigates a new type of solar heat pump dryer directly driven by photovoltaic panels. In order to design this system, a mathematical model has been established describing the whole drying process, including models of key components and phenomena of heat and mass transfer at the product layer and the air. The results of simulation at different drying air temperatures and velocities have been calculated and it indicate that the temperature of drying air is crucial external parameter compared to the velocity, with the increase of drying temperature from 45°C to 55°C, the product moisture content (Kg water/Kg dry product) decreased from 0.75 Kg/Kg to 0.3 Kg/Kg.

Drying of Ceramic Hollow Bricks in an Industrial Tunnel Dryer: A Finite Volume Analysis

Directory of Open Access Journals (Sweden)

F Tavares

2016-10-01

Full Text Available This paper aims to study the drying of industrial hollow bricks in a tunnel dryer cross flow type. The theoretical model is based on mass and energy conservation equations applied to air and product. To validate the methodology, numerical and experimental results for the moisture content and the temperature of brick during the drying in an industrial scale are compared and a good correlation was obtained. Results of moisture content and temperature of the product, and temperature, relative humidity and absolute humidity of drying air as a function of drying time and position in the dryer are presented and analyzed.

Analysis of efficiency of a solar dryer tunnel type of mango pulp; Analisis de la eficiencia de un secador solar tipo tunel para pulpa de mango

Energy Technology Data Exchange (ETDEWEB)

Chagoyan Serrano, Jose [Universidad Autonoma de Baja California Sur, La Paz, Baja California Sur (Mexico)

2000-07-01

A new method to assess the performance of a solar dryer is presented. It describes energy efficiency indicators to improve a commercial dryer design. First, a preliminary dryer design procedure is described step by step. Then, two different modes of a tunnel dryer are investigated: Batch and semi-continue operations. The results of the analysis show that, the thermal efficiency is not sufficient to rate de dryer performance. It is necessary to include the productivity of the drying process and the quality of the dried fruit. The drying process and productivity tend to go hand-in-hand but in opposite directions. That is to say, raising the thermal efficiency reduce the process productivity and conversely. The analysis also suggests that an agreement between the efficiency, productivity and the quality must be specified in the drier design. [Spanish] Se presenta un procedimiento nuevo para evaluar la operacion de un secador solar, con el cual se precisan indicadores de la eficiencia que pueden ser utiles para mejorar el diseno del equipo. Se empieza por describir los pasos de un procedimiento de diseno preliminar de un sistema de secado. Despues, se analizan cualitativamente dos secadores: uno que opera por lotes y el otro de modo semicontinuo. Los resultados del analisis muestran que, la eficiencia termica del equipo no es un criterio suficiente para evaluar su operacion; tambien se requiere tomar encuenta la productividad del proceso de secado y la calidad del producto final. Se concluye que la eficiencia termica y la productividad del proceso son conceptos encontrados. Es decir, la eficiencia termica del equipo no es un criterio suficiente para evaluar su operacion; tambien se requiere tomar en cuenta la productividad del proceso de secado y la calidad del producto final. Se concluye que la eficiencia termica y la productividad del proceso son conceptos encontrados. Es decir, la eficiencia termica solo se puede aumentar a costa de la productividad y viceversa

Composition and activity variations in bulk gas of drum waste packages of Paks NPP

International Nuclear Information System (INIS)

Molnar, M.; Palcsu, L.; Svingor, E.; Szanto, Zs.; Futo, I.; Ormai, P.

2001-01-01

To obtain reliable estimates of the quantities and rates of the gas production a series of measurements was carried out in drum waste packages generated and temporarily stored at the site of Paks Nuclear Power Plant (Paks NPP). Ten drum waste packages were equipped with sampling valves for repeated sampling. Nine times between 04/02/2000 and 19/07/2001 qualitative gas component analyses of bulk gases of drums were executed. Gas samples were delivered to the laboratory of the ATOMKI for tritium and radiocarbon content measurements.(author)

Infrared thermography applied to monitoring of radioactive waste drums; Termografia infravermelha aplicada ao monitoramento de tambores de rejeitos radioativos

Energy Technology Data Exchange (ETDEWEB)

Kelmer, P.; Camarano, D.M. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Calado, F.; Phillip, B.; Viana, C.; Andrade, R.M., E-mail: paulafuziki@yahoo.com.br, E-mail: flavio.arcalado@gmail.com, E-mail: bruno.phil@gmail.com, E-mail: criisviana@hotmail.com, E-mail: rma@ufmg.br, E-mail: dmc@cdtn.br [Universidade Federal de Minas Gerais (UFMG), Belo Horizonte, MG (Brazil). Departamento de Engenharia Eletrica

2013-07-01

The use of thermography in the inspection of drums containing radioactive waste is being stimulated by the absence of physical contact. In Brazil the majority of radioactive wastes are compacted solids packed in metal drums stored temporarily for decades and requires special attention. These drums have only one qualitative indication of the radionuclides present. However, its structural condition is not followed systematically. The aim of this work is presents a methodology by applying thermography for monitoring the structural condition of drums containing radioactive waste in order to detect degraded regions of the drums. (author)

Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

Energy Technology Data Exchange (ETDEWEB)

Jonassen, Ola

1999-10-01

The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidising gas, (3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger, and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

Low-Level Waste Drum Assay Intercomparison Study

International Nuclear Information System (INIS)

Greutzmacher, K.; Kuzminski, J.; Myers, S. C.

2003-01-01

Nuclear waste assay is an integral element of programs such as safeguards, waste management, and waste disposal. The majority of nuclear waste is packaged in drums and analyzed by various nondestructive assay (NDA) techniques to identify and quantify the radioactive content. Due to various regulations and the public interest in nuclear issues, the analytical results are required to be of high quality and supported by a rigorous Quality Assurance (QA) program. A valuable QA tool is an intercomparison program in which a known sample is analyzed by a number of different facilities. While transuranic waste (TRU) certified NDA teams are evaluated through the Performance Demonstration Program (PDP), low-level waste (LLW) assay specialists have not been afforded a similar opportunity. NDA specialists from throughout the DOE complex were invited to participate in this voluntary drum assay intercomparison study that was organized and facilitated by the Solid Waste Operations and the Safeguards Science and Technology groups at the Los Alamos National Laboratory and by Eberline Services. Each participating NDA team performed six replicate blind measurements of two 55-gallon drums with relatively low-density matrices (a 19.1 kg shredded paper matrix and a 54.4 kg mixed metal, rubber, paper and plastic matrix). This paper presents the results from this study, with an emphasis on discussing the lessons learned as well as desirable follow up programs for the future. The results will discuss the accuracy and precision of the replicate measurements for each NDA team as well as any issues that arose during the effort

Special closures for steel drum shipping containers

International Nuclear Information System (INIS)

Bonzon, L.L.; Otts, J.V.

1976-01-01

The objective of this program was to develop special lid closures for typical, steel drum, radioactive material shipping containers. Previous experience and testing had shown that the existing container was adequate to withstand the required environmental tests for certification, but that the lid and closure were just marginally effective. Specifically, the lid closure failed to consistently maintain a tight seal between the container and the lid after drop tests, thus causing the package contents to be vulnerable in the subsequent fire test. Recognizing the deficiency, the United States Energy Research and Development Administration requested the development of new closure(s) which would: (1) be as strong and resistant to a drop as the bottom of the container; (2) have minimal economic impact on the overall container cost; (3) maximize the use of existing container designs; (4) consider crush loads; and (5) result in less dependence on personnel and loading procedures. Several techniques were evaluated and found to be more effective than the standard closure mechanism. Of these, three new closure techniques were designed, fabricated, and proven to be structurally adequate to provide containment when a 454-kg drum was drop tested from 9.14-m onto an unyielding surface. The three designs were: (1) a 152-mm long lid extension or skirt welded to the standard drum lid, (2) a separate inner lid, with 152-mm long skirt and (3) C-clamps used at the container-lid interface. Based upon structural integrity, economic impact, and minimal design change, the lid extension is the recommended special closure

Design and Testing of a Natural Convection Solar Tunnel Dryer for Mango

Directory of Open Access Journals (Sweden)

Isaac Nyambe Simate

2017-01-01

Full Text Available A natural convection solar tunnel dryer comprising three major units, a solar collector unit, a drying unit, and a vertical bare flat-plate chimney, was constructed. No-load tests with a horizontal configuration of air entry into the collector resulted in a bidirectional air flow in the dryer. To correct this undesirable situation, an air guide at the collector was incorporated to ensure that air entered in a vertical direction. To investigate its performance, drying experiments with mango were carried out at the University of Zambia, Department of Agricultural Engineering. Uncertainties in the parameters measured in the experiment were analysed and quantified. The results showed that, under solar radiation between 568.4 and 999.5 W/m2, air temperature of up to 65.8°C was attained at the collector unit. The average relative humidity values were 30.8%, 6.4%, and 8.4% for the ambient, collector, and drying unit, respectively. Under these conditions, mango with an initial moisture content of 85.5% (wet basis was dried to 13.0% (wet basis in 9.5 hours. The collector, drying, and pick-up efficiencies were found to be 24.7%, 12.8%, and 35.0%, respectively. The average temperature difference between the chimney air and ambient air was 12.1°C, and this was sufficient in driving the flow of air through the dryer.

Fluid bed dryer and Aeropep solidification system. Amendment 1 to topical report

International Nuclear Information System (INIS)

1975-01-01

Information is presented on interfaces between the aerojet fluid bed dryer and the liquid radwaste system, plant ventilation system, and radioactive solid waste handling system for BWR and PWR type reactors. (U.S.)

Determination of stresses caused by fluctuation of acoustic load in the steam dryers of a BWR

International Nuclear Information System (INIS)

Centeno P, J.; Quezada G, S.; Prieto G, A.; Vazquez R, A.; Espinosa P, G.; Nunez C, A.

2014-10-01

The extended power up-rate (EPU) in a nuclear power plant cause various problems in BWR components also in the steam system. This due to increased steam flow generated in the reactor and is conveyed to the turbine by the four main steam lines (MSL). One of the most serious problems is the generation of acoustic pressure loads in the metal structure of the steam dryer which eventually leads to fatigue failure and even the appearance of cracks, and in turn it causes loose parts that are entrained by the steam and transported in the MSL. This problem is due to the fluctuation of load acoustics caused by the union of the safety or relief valves (SRV) with the MSL, spreading through these to reach the reactor pressure vessel (RPV) where the effect of resonance of the acoustic wave is amplified and impacts directly in the supporting structure of the steam dryer, skirt and the panels where the mixture liquid-steam is dried, by centrifugation effect and runoff of liquid water. Efforts in the steam dryer operating conditions of EPU for two cases will be analyzed in this work, the first is before the installation of Acoustic Side Branch (ASB), and in the second case we consider the installation of said ASB in the standpipes of SRV. The analysis was performed with numerical experiments on a platform for computational fluid dynamics with virtual geometries previously designed based on the actual components of the reactor and steam system. The model to study is delimited by the top of the RPV, the steam dryer and a section of each of the four MSL with ten standpipes of SRV. With the obtained data and considering the mechanical-structural properties of the steam dryer material, we can evaluate the mechanical resistance to impacts by acoustic pressure load and its possible deformation or cracking. (Author)

Intelligent mobile sensor system for drum inspection and monitoring: Phase 1

International Nuclear Information System (INIS)

1993-06-01

The objective of this project was to develop an operational system for monitoring and inspection activities for waste storage facility operations at several DOE sites. Specifically, the product of this effort is a robotic device with enhanced intelligence and maneuverability capable of conducting routine inspection of stored waste drums. The device is capable of operating in narrow aisles and interpolating the free aisle space between rows of stacked drums. The system has an integrated sensor suite for leak detection, and is interfaced with a site database both for inspection planning and for data correlation, updating, and report generation. The system is capable of departing on an assigned mission, collecting required data, recording which positions of its mission had to be aborted or modified due to environmental constraints, and reporting back when the mission is complete. Successful identification of more than 90% of all drum defects has been demonstrated in a high fidelity waste storage facility mockup. Identified anomalies included rust spots, rust streaks, areas of corrosion, dents, and tilted drums. All drums were positively identified and correlated with the site database. This development effort is separated into three phases of which phase one is now complete. The first phase has demonstrated an integrated system for monitoring and inspection activities for waste storage facility operations. This demonstration system was quickly fielded and evaluated by leveraging technologies developed from previous NASA and DARPA contracts and internal research. The second phase will demonstrate a prototype system appropriate for operational use in an actual storage facility. The prototype provides an integrated design that considers operational requirements, hardware costs, maintenance, safety, and robustness. The final phase will demonstrate commercial viability using the prototype vehicle in a pilot waste operations and inspection project

The Saami drums and the religious encounter in the 17th and 18th centuries

Directory of Open Access Journals (Sweden)

Håkan Rydving

1991-01-01

Full Text Available From the end of the 17th to the middle of the 18th century much of the confrontation between indigenous Saami religion and Christianity was focused on the drums. The Saamis of both Denmark—Norway and Sweden—Finland had been christianized for decade. The main problem for the Church authorities turned out to be that of making the Saamis abandon their indigenous religious customs. From the end of the 17th century, an intense period of propaganda and coercion began to make the Saamis abandon these non Christian elements in their religion. For the Saamis, the drums represented their threatened culture, the resistance against the Christian claim to exclusiveness, and a striving to preserve traditional values. The drums had a twofold role to play in the religious encounter. They were both foci of the confrontation and sources documenting and structuring it. The fight between old and new beliefs is to some extent possible to follow in the records from the district and county courts. These records give us access to Saami arguments and views of the importance of the drums in Saami society. The function of the drums as instruments for a Saami description of the encounter is, however, difficult to make out. The drum figures are difficult to interpret and there are a number of alternative ways of understanding their meaning.

Analysis of force variance for a continuous miner drum using the Design of Experiments method

Energy Technology Data Exchange (ETDEWEB)

S. Somanchi; V.J. Kecojevic; C.J. Bise [Pennsylvania State University, University Park, PA (United States)

2006-06-15

Continuous miners (CMs) are excavating machines designed to extract a variety of minerals by underground mining. The variance in force experienced by the cutting drum is a very important aspect that must be considered during drum design. A uniform variance essentially means that an equal load is applied on the individual cutting bits and this, in turn, enables better cutting action, greater efficiency, and longer bit and machine life. There are certain input parameters used in the drum design whose exact relationships with force variance are not clearly understood. This paper determines (1) the factors that have a significant effect on the force variance of the drum and (2) the values that can be assigned to these factors to minimize the force variance. A computer program, Continuous Miner Drum (CMD), was developed in collaboration with Kennametal, Inc. to facilitate the mechanical design of CM drums. CMD also facilitated data collection for determining significant factors affecting force variance. Six input parameters, including centre pitch, outer pitch, balance angle, shift angle, set angle and relative angle were tested at two levels. Trials were configured using the Design of Experiments (DoE) method where 2{sup 6} full-factorial experimental design was selected to investigate the effect of these factors on force variance. Results from the analysis show that all parameters except balance angle, as well as their interactions, significantly affect the force variance.

First Industrial Tests of a Matrix Monitor Correction for the Differential Die-away Technique of Historical Waste Drums

Energy Technology Data Exchange (ETDEWEB)

Antoni, Rodolphe; Passard, Christian; Perot, Bertrand [CEA Cadarache DEN/Nuclear Measurement Laboratory, 13108 Saint-Paul lez Durance (France); Batifol, Marc; Vandamme, Jean-Christophe [Nuclear Measurement Team, AREVA NC, La Hague plant F-50444 Beaumont-Hague (France); Grassi, Gabriele [AREVA NC, 1 place Jean-Millier, 92084 Paris-La-Defense cedex (France)

2015-07-01

The fissile mass in radioactive waste drums filled with compacted metallic residues (spent fuel hulls and nozzles) produced at AREVA NC La Hague reprocessing plant is measured by neutron interrogation with the Differential Die-away measurement Technique (DDT). In the next years, old hulls and nozzles mixed with Ion-Exchange Resins will be measured. The ion-exchange resins increase neutron moderation in the matrix, compared to the waste measured in the current process. In this context, the Nuclear Measurement Laboratory (LMN) of CEA Cadarache has studied a matrix effect correction method, based on a drum monitor, namely a 3He proportional counter located inside the measurement cavity. After feasibility studies performed with LMN's PROMETHEE 6 laboratory measurement cell and with MCNPX simulations, this paper presents first experimental tests performed on the industrial ACC (hulls and nozzles compaction facility) measurement system. A calculation vs. experiment benchmark has been carried out by performing dedicated calibration measurements with a representative drum and {sup 235}U samples. The comparison between calculation and experiment shows a satisfactory agreement for the drum monitor. The final objective of this work is to confirm the reliability of the modeling approach and the industrial feasibility of the method, which will be implemented on the industrial station for the measurement of historical wastes. (authors)

Simultaneous correction of attenuation and geometric response in emission tomography applied to nuclear waste drums

International Nuclear Information System (INIS)

Thierry, Raphael

1999-01-01

Multi-photonic emission tomography is a non destructive technique applied to the control of radioactive waste drums. The emitted gamma rays are detected on the range [50 keV, 2 MeV] by a hyper pure germanium, of high resolution in energy, which enables to set up a detailed list of radionuclides contained within the drum. From different points of measurement located in a transaxial plane of the drum, the activity distribution is computed by a reconstruction algorithm. An algebraic modelling of the physical process has been developed in order to correct the different degrading phenomenon, in particular the attenuation and the detector geometric response. Attenuation through the materials constituting the barrel is the preponderant phenomena. Its ignorance prevents from accurate activity quantification. Its correction has been realised from an attenuation map obtained by a transmission tomograph. The detector geometric response, introducing a blurring within the detection, is compensated by an analytic model. An adequate modelling of those phenomenon is primordial: it highly contributes on a large scale the image quality and the quantification. The image reconstruction, requiring the resolution of sparse linear system, is realised by iterative algorithms. Due to the 'ill-posed' nature of tomographic reconstruction, it is necessary to use regularisation: by introducing an a priori information on the solution, the stabilisation of the methods is carried out. We chose to minimise the Maximum A Posteriori criterion. Its resolution is considered with a half-quadratic regularisation: it permits the preservation of natural discontinuities, and avoids global-over smoothing of the image. It is evaluated on real phantoms and waste drums. Efficient sampling of the data is considered. (author) [fr

Commercial Demonstration of the Manufactured Aggregate Processing Technology Utilizing Spray Dryer Ash

Energy Technology Data Exchange (ETDEWEB)

Milton Wu; Paul Yuran

2006-12-31

Universal Aggregates LLC (UA) was awarded a cost sharing Co-operative Agreement from the Department of Energy (DOE) through the Power Plant Improvement Initiative Program (PPII) to design, construct and operate a lightweight aggregate manufacturing plant at the Birchwood Power Facility in King George, Virginia in October 2001. The Agreement was signed in November 2002. The installation and start-up expenses for the Birchwood Aggregate Facility are $19.5 million. The DOE share is $7.2 million (37%) and the UA share is $12.3 million (63%). The original project team consists of UA, SynAggs, LLC, CONSOL Energy Inc. and P. J. Dick, Inc. Using 115,000 ton per year of spray dryer ash (SDA), a dry FGD by-product from the power station, UA will produce 167,000 tons of manufactured lightweight aggregate for use in production of concrete masonry units (CMU). Manufacturing aggregate from FGD by-products can provide an economical high-volume use and substantially expand market for FGD by-products. Most of the FGD by-products are currently disposed of in landfills. Construction of the Birchwood Aggregate Facility was completed in March 2004. Operation startup was begun in April 2004. Plant Integration was initiated in December 2004. Integration includes mixing, extrusion, curing, crushing and screening. Lightweight aggregates with proper size gradation and bulk density were produced from the manufacturing aggregate plant and loaded on a stockpile for shipment. The shipped aggregates were used in a commercial block plant for CMU production. However, most of the production was made at low capacity factors and for a relatively short time in 2005. Several areas were identified as important factors to improve plant capacity and availability. Equipment and process control modifications and curing vessel clean up were made to improve plant operation in the first half of 2006. About 3,000 tons of crushed aggregate was produced in August 2006. UA is continuing to work to improve plant

Non-intrusive measurement of tritium activity in waste drums by modelling a 3He leak quantified by mass spectrometry

International Nuclear Information System (INIS)

Demange, D.

2002-01-01

This study deals with a new method that makes it possible to measure very low tritium quantities inside radioactive waste drums. This indirect method is based on measuring the decaying product, 3 He, and requires a study of its behaviour inside the drum. Our model considers 3 He as totally free and its leak through the polymeric joint of the drum as two distinct phenomena: permeation and laminar flow. The numerical simulations show that a pseudo-stationary state takes place. Thus, the 3 He leak corresponds to the tritium activity inside the drum but it appears, however, that the leak peaks when the atmospheric pressure variations induce an overpressure in the drum. Nevertheless, the confinement of a drum in a tight chamber makes it possible to quantify the 3 He leak. This is a non-intrusive measurement of its activity, which was experimentally checked by using reduced models, representing the drum and its confinement chamber. The drum's confinement was optimised to obtain a reproducible 3 He leak measurement. The gaseous samples taken from the chamber were purified using selective adsorption onto activated charcoals at 77 K to remove the tritium and pre-concentrate the 3 He. The samples were measured using a leak detector mass spectrometer. The adaptation of the signal acquisition and the optimisation of the analysis parameters made it possible to reach the stability of the external calibrations using standard gases with a 3 He detection limit of 0.05 ppb. Repeated confinement of the reference drums demonstrated the accuracy of this method. The uncertainty of this non-intrusive measurement of the tritium activity in 200-liter drums is 15% and the detection limit is about 1 GBq after a 24 h confinement. These results led to the definition of an automated tool able to systematically measure the tritium activity of all storage waste drums. (authors)

performance evaluation of a pebble bed solar crop dryer abstract

African Journals Online (AJOL)

Dr Obe

The open-air sun drying is prevalent and very common in the rural areas. Farmers spread their agricultural produce such as maize, cassava, pepper, tomatoes etc. ... drying system. The abundance of solar radiation in. Nigeria could make crop drying with solar dryers very easy and simple. Economic appraisal of solar drying ...

Field test results for radioactive waste drum characterization with Waste Inspection Tomography (WIT)

Energy Technology Data Exchange (ETDEWEB)

Bernardi, R.T. [Bio-Imaging Research, Inc., Lincolnshire, IL (United States)

1997-11-01

This paper summarizes the design, fabrication, factory testing, evaluation and demonstration of waste inspection tomography (WIT). WIT consists of a self-sufficient, mobile semi-trailer for Non-Destructive Evaluation and Non-Destructive Assay (NDE/NDA) characterization of nuclear waste drums using X-ray and gamma-ray tomographic techniques. The 23-month WIT Phase I initial test results include 2 MeV Digital Radiography (DR), Computed Tomography (CT), Anger camera imaging, Single Photon Emission Computed Tomography (SPECT), Gamma-Ray Spectroscopy, Collimated Gamma Scanning (CGS), and Active and Passive Computed Tomography (A&PCT) using a 1.4 mCi source of {sup 166}Ho. These techniques were initially demonstrated on a 55-gallon phantom drum with three simulated waste matrices of combustibles, heterogeneous metals, and cement using check sources of gamma active isotopes. Waste matrix identification, isotopic identification, and attenuation-corrected gamma activity determination were all demonstrated nondestructively and noninvasively. Preliminary field tests results with nuclear waste drums are summarized. WIT has inspected drums with 0 to 20 grams plutonium 239. The minimum measured was 0.131 gram plutonium 239 in cement. 8 figs.

Estimation of build up of dose rate on U3O8 product drum

International Nuclear Information System (INIS)

Pandey, J.P.N.; Shinde, A.M.; Deshpande, M.D.

2008-01-01

In fuel reprocessing plant, plutonium oxide and uranium oxide (U 3 O 8 ) are products. Approximately 180 kg U 3 O 8 is filled in SS drum and sealed firmly before storage. In PHWR natural uranium (UO 2 ) is used as fuel. In natural uranium, thorium-232 is present as an impurity at few tens of ppm level. During irradiation in power reactors, due to nuclear reaction formation of 232 U from 232 Th takes place. Natural decay of 232 U leads to the formation of 208 Tl. As time passes, there is buildup of 208 Tl and hence increase in dose rate on the drum containing U 3 O 8 . It is essential to estimate the buildup of dose rate considering the external radiological hazards involved during U 3 O 8 drum handling, transportation and fuel fabrication. This paper describes the calculation of dose rate on drum in future years using MCNP code. For dose rate calculation decay of fission product activity which remains as contamination in product and build up of '2 08 Tl from 232 U is considered. Some measured values of dose rate on U 3 O 8 drum are given for the comparisons with estimated dose rate based on MCNP code. (author)

Optimum method to determine gamma activity in 200 liter drums. In-toto measurement or extracting a sample

International Nuclear Information System (INIS)

Bronson, Frazier

2008-01-01

In the process of decommissioning contaminated facilities, and in the conduct of normal operations involving radioactive material, it is frequently required to measure radioactivity in large containers such as 200 liter drums. For solid material, it is quite unusual for the radioactivity to be homogeneously distributed throughout the container. One way to derive the concentration of radioactivity within the container is to extract a sample for subsequent measurement in the laboratory. Another way is to use gamma spectroscopy and assay the entire container, or in-toto measurement. This paper examines the process of determining the best way to estimate the activity within the container, and gives quantitative estimates of measurement uncertainty for various conditions of radioactivity contained within 200 liter drums. When the contents of the container are not homogeneous, the sampling uncertainty is likely to be larger than the in-toto measurement uncertainty. (author)

On the efficiency calibration of a drum waste assay system

CERN Document Server

Dinescu, L; Cazan, I L; Macrin, R; Caragheorgheopol, G; Rotarescu, G

2002-01-01

The efficiency calibration of a gamma spectroscopy waste assay system, constructed by IFIN-HH, was performed. The calibration technique was based on the assumption of a uniform distribution of the source activity in the drum and also a uniform sample matrix. A collimated detector (HPGe--20% relative efficiency) placed at 30 cm from the drum was used. The detection limit for sup 1 sup 3 sup 7 Cs and sup 6 sup 0 Co is approximately 45 Bq/kg for a sample of about 400 kg and a counting time of 10 min. A total measurement uncertainty of -70% to +40% was estimated.

Development of an active solar crop dryer: design analysis and ...

African Journals Online (AJOL)

The design analysis and performance evaluation of an active solar crop dryer was undertaken by drying marched cassava. The drying rate, system drying, collector and pick-up efficiencies were 1.6kg/day (14%/day), 9%, 46% and 29% respectively. Comparatively, the drying rate for sun drying was 0.9kg/day. The collector ...

Plasma Glucose Levels for Red Drum Sciaenops Ocellatus in a Florida Estuarine Fisheries Reserve

Science.gov (United States)

Bourtis, Carla M.; Francis-Floyd, Ruth; Boggs, Ashley S P.; Reyier, Eric A.; Stolen, Eric D.; Yanong, Roy P.; Guillette, Louis J., Jr.

2015-01-01

Despite the significant value of the southeastern United States' red drum (Sciaenops ocellatus) fishery, there is a lack of clinical blood chemistry data. This was the first study to assess plasma glucose values as an indicator of stress response to evaluate variation and the effect of reproductive activity for wild adult red drum in Florida. Red drum (n=126) were collected from NASA's Kennedy Space Center waters during three reproductive periods in 2011. Samples were obtained from the branchial vessels of the gill arch. Plasma glucose levels were significantly different among reproductive periods, with the highest mean values recorded during the spawning period, September- October (38.23 mg / dL +/- 10.0). The glucose range was 17 - 69 mg / dL. Glucose values were lower during all three periods than previous values recorded for cultured or captive red drum studies. This may indicate that fish from this population were under less stress than other populations previously sampled.

Online Monitoring of Temperature Using Wireless Module in a Rotating Drum-Applicable to Leather Industries

Directory of Open Access Journals (Sweden)

T. Narayani

2015-07-01

Full Text Available In order to ensure safe and efficient operation of unit processes, foremost requirement is accurate measurement of process variables, with which quality can be monitored and controlled. Understanding the necessity of online monitoring of process temperature in tanning/dyeing process, the article is focused on wireless measurement of physical parameters involved in wet processing of hides/ skins and monitoring through digital computer for further analysis. It’s a challenging task to measure and communicate the process information from a closed rotating drum. Wireless communication is proposed because of its enhanced security, superfast operating speed, and increased mobility. The physical parameters which are predominant in tanning process are temperature, pH, conductivity etc. of the process fluid. It is necessary to carryout dyeing at 65 0C for producing raw to wet blue process. As a first attempt, wireless module for temperature measurement has been developed. The module includes signal transmitter and receiver section. In the transmitter section, the temperature which is measured by an integrated sensor is converted into frequency signal and imposed on a radio frequency signal (career signal and get transmitted in air. On the other side, receiver section receives the radio frequency signal and converts that into electrical signals to interface with the digital computer for online monitoring. The module is able to receive and control temperature of tanning drum within a distance of 100 meters. Real time experiments on the fabricated model show interesting results for commercialization.

Vibration Analysis for Steam Dryer of APR1400 Steam Generator

Energy Technology Data Exchange (ETDEWEB)

Han, Sung-heum; Ko, Doyoung [KHNP CRI, Daejeon (Korea, Republic of); Cho, Minki [Doosan Heavy Industry, Changwon (Korea, Republic of)

2016-10-15

This paper is related to comprehensive vibration assessment program for APR1400 steam generator internals. According to U.S. Nuclear Regulatory Commission, Regulatory Guide 1.20 (Rev.3, March 2007), we conducted vibration analysis for a steam dryer as the second steam separator of steam generator internals. The vibration analysis was performed at the 100 % power operating condition as the normal operation condition. The random hydraulic loads were calculated by the computational fluid dynamics and the structural responses were predicted by power spectral density analysis for the probabilistic method. In order to meet the recently revised U.S. NRC RG 1.20 Rev.3, the CVAP against the potential adverse flow effects in APR1400 SG internals should be performed. This study conducted the vibration response analysis for the SG steam dryer as the second moisture separator at the 100% power condition, and evaluated the structural integrity. The predicted alternating stress intensities were evaluated to have more than 17.78 times fatigue margin compared to the endurance limit.

Drying of carrot slices in a triple pass solar dryer

Directory of Open Access Journals (Sweden)

Seshachalam Kesavan

2017-01-01

Full Text Available An indirect triple pass forced convection solar dryer was developed and its performance was evaluated for drying of carrot slices. The drying experiments were carried out under the meteorological conditions of Coimbatore city in India during the year 2016. The experimental set-up consists of a blower, triple pass packed bed air collector (using sand with wire mesh absorber plate, and a drying chamber. The air mass flow rate was optimized to 0.062 kg/s. The initial moisture content of the carrot slices was reduced from 87.5% (on wet basis to the final moisture content of 10% (wet basis in 6 h duration. The thin layer drying characteristics were analyzed using twelve mathematical models available in open literature. The results showed that the pick-up efficiency of the dryer was varied in the range between 14 and 43% with an average air collector thermal efficiency of 44% during the experimentation. The drying characteristics of carrot slices was predicted with good degree of accuracy using Wang and Singh drying model.

KAJIAN TEKNIS-EKONOMIS ALAT PENGERING PATI SAGU MODEL CROSS FLOW VIBRO FLUIDIZED BED (Study on Technical-Economic of Sago Starch Dryer Model of Cross Flow Vibro Fluidized Bed

Directory of Open Access Journals (Sweden)

Abadi Jading

2015-02-01

Full Text Available The purpose of this research was to evaluate performance of vibro cross flow fluidized bed dryer using biomass fuel for drying sago starch. The phase of research were evaluation of dryer heated by a biomass stove using coconut shell as a fuel and observation of the drying temperature, moisture content, drying time, energy analysis, and drying effiviency, as well as calculation of its economic analysis. The dryer has dimension of 200x50x1500 cm for length, width, hight, respectively, and working capacity of 35kg/process. The results showed that biomass fuel consumption for drying sago starch for 7 hours was 12740,00 MJ (70 kg/process and electricity consumption for blower and vibrator was 37,80 MJ. Furthermore, the dryer reduced moisture content of sago starch from 42% (wb to 12% (wb with temperature in the vibrator chamber of 40-60 oC and relative humidity of 50%, as well as ambient temperature of 30 3C and drying efficiency of 46,02%. Economic analysis showed that the dryer had NPV of Rp. 16.002.858, BCR of 1,53, IRR of 35%, and PBP of 3,51 years. Keywords: Cross flow, vibro fluidized bed dryer, biomass stoves, sago starch, financial analysis   ABSTRAK Tujuan penelitian ini adalah melakukan pengujian terhadap alat pengering pati berbasis sagu model cross flow vibrofluidized bed bertenaga biomassa. Tahapan penelitian meliputi pengujian alat pengering menggunakan tungku biomassa berbahan bakar tempurung kelapa dengan melakukan pengamatan suhu selama pengeringan, penurunan kadar air, waktu pengeringan, kebutuhan energi, efisiensi pengering, dan analisis finansial. Konstruksi alat pengering pati sagu model vibro fluidized bed bertenaga biomassa berukuran panjang, lebar dan tinggi masing-masing (200x50x1500 cm, serta memiliki daya tampung atau kapasitas maksimum pati sagu basah 35 kg/proses. Hasil pengujian menunjukkan bahwa alat pengering ini mampu mengeringkan pati sagu selama 7 jam, dengan konsumsi bahan bakar tempurung kelapa sebanyak 70 kg

OPTIMIZATION OF TRANSIEN PROCESSES OF WATER LEVEL VARIATION IN DRUM OF STEAM BOILERS

Directory of Open Access Journals (Sweden)

G. T. Kulakov

2014-01-01

Full Text Available The work of regulator in general three-impulse automatic control system of water level in drum of boiler doesn’t supply quality of internal and external disturbance attack (presentation of regulation mistakes. That is why it is needed to improve. Different methods of proportional plus reset controller regulation of three-phase automatic feed control system are considered. There were suggested new methods to improve the quality of regulation of water level in boilers. Here the step system of automatic regulation was determined, on the base of transfer function.It is noticed that optimal transient processes supply calculation of numerical value of transmission factor of regulator at g =2,618, it is more then was recommended, but statistic mistakes remain. The transient simulation method in fast-time scale is recommended, this allow to determine early the value of statistic mistake of regulation by disturbances of reheated steam consumption and properly change the task to compensating device of step automatic control system. And numerical value of time constant criteria  should be calculated on the base of numbers of golden section(Phi, taking into account the definite time constant of lead section and time-lag, time-lag on controlled influence channel, and also taking into account maximum value of controlled influence. This method allow to reduce in two times the total time of regulation, to decrease absolute mistake of regulation in three times, and maximum value of regulation influence by feedwater in 1,7 times.

Kinematics and Path Following Control of an Articulated Drum Roller

Science.gov (United States)

BIAN, Yongming; YANG, Meng; FANG, Xiaojun; WANG, Xiahui

2017-07-01

Automatic navigation of an articulated drum roller, which is an articulated steering type vehicle widely used in the construction industry, is highly expected for operation cost reduction and improvement of work efficiency. In order to achieve the path following control, considering that its steering system is articulated steering and two frames are articulated by an active revolute joint, a kinematic model and an error dynamic state-space equation of an articulated drum roller are proposed. Besides, a state-feedback control law based on Lyapunov stability theory is also designed, which can be proved to achieve the purpose of control by the analysis of stability. What's more, to evaluate the performance of the proposed method, simulation under the MATLAB/Simulink and experiments using positioning algorithm and errors correction at the uneven construction site are performed, with initial displacement error (-1.5 m), heading error (-0.11 rad) and steering angle (-0.19 rad). Finally, simulation and experimental results show that the errors and steering angle can decrease gradually, and converge to zero with time. Meanwhile, the control input is not saturated. An articulated drum roller can lock into a desired path with the proposed method in uneven fields.

Estimation of possibility of brittle fracture in high pressure boiler drums

International Nuclear Information System (INIS)

Grin', E.A.

2005-01-01

Paper presents the results of analysis of the problem to ensure brittle strength of high pressure boiler drums made with application of the present-day methods of linear and nonlinear fracture mechanics. The charts of the temperature boundaries of brittle fracture and of the critical factors of stress intensity plotted depending on the actual properties of the material and on dimensions of flaws are presented for standard size drums made of 22K and 16GNM steels. In the paper there are some examples of the practical application of the given charts [ru

Life cycle energy metrics and CO 2 credit analysis of a hybrid photovoltaic/thermal greenhouse dryer

OpenAIRE

P. Barnwal; G. N. Tiwari

2008-01-01

In this paper, life cycle energy metrics, such as energy payback time (EPBT), energy production factor (EPF) and life cycle conversion efficiency (LCCE), and mitigation of CO 2 emissions for a hybrid photovoltaic/thermal (PV/T) greenhouse dryer have been analyzed. The hybrid PV/T greenhouse (roof type even span) dryer, designed and constructed at Solar Energy Park, Indian Institute of Technology, New Delhi (28°35′N, 77°12′E, 216 m above MSL), India, has a 2.50 m × 2.60 m floor area, 1.80 m ce...

Humidity level In psychrometric processes

International Nuclear Information System (INIS)

Mojsovski, Filip

2008-01-01

When a thermal engineer needs to control, rather than merely moderate humidity, he must focus on the moisture level as a separate variable - not simply an addition of temperature control. Controlling humidity generally demands a correct psychrometric approach dedicated to that purpose [1].Analysis of the humidity level in psychrometric thermal processes leads to relevant data for theory and practice [2]. This paper presents: (1) the summer climatic curve for the Skopje region, (2) selected results of investigation on farm dryers made outside laboratories. The first purpose of such activity was to examine relations between weather conditions and drying conditions. The estimation of weather condition for the warmest season of the year was realized by a summer climatic curve. In the science of drying, basic drying conditions are temperature, relative humidity and velocity of air, thickness of dried product and dryer construction. The second purpose was to realize correct prediction of drying rates for various psychrometrics drying processes and local products. Test runs with the dryer were carried out over a period of 24 h, using fruits and vegetables as experimental material. Air flow rate through the dryer of 150 m3/h, overall drying rate of 0.04 kg/h and air temperature of 65 oC were reached. Three types of solar dryers, were exploited in the research.

Energy aAnalysis and Kinetics of Mint Leaves Dehydration Using Vibro-Fluidized Bed Heat Pump Dryer

Directory of Open Access Journals (Sweden)

S. M Ataei Ardestani

2015-03-01

Full Text Available Fluidized bed dryers have not yet been used for drying products such as mint leaves. This could be due to high porosity and low mechanical resistance resulting in poor quality of fluidization. Applying vibration has been recommended to overcome problems such as channeling and defluidization, and hence improving the fluidization quality. In this research, a laboratory scale vibro-fluidized bed heat pump dryer was designed and constructed for drying mint leaves. The experiments were conducted at vibration frequency of 80 Hz and amplitude of 3 mm. The velocity and temperature of the inlet air was controlled by an automatic control system. Experiments were carried out at 40, 50 and 60 °C, and two methods: heat pump drying (HPD and non-heat pump drying (NHPD. The results revealed that drying process primarily occurred in the falling rate period. Effective moisture diffusivity of the samples increased with increase in drying air temperature and varied from 4.26656×10-11 to 2.95872×10-10 m2 s-1 for the HPD method, and 3.71918×10-11 to 1.29196×10-10 m2 s-1 for the NHPD method and was within the reported range of 10-9 to 10-11 m2 s-1 for drying of food materials. The activation energy was determined to be 84 kJ mol-1 for the HPD and 54.34 kJ mol-1 for the NHPD, both have very good agreement with the results of other investigators. The coefficient of performance and specific moisture evaporation rate showed the acceptable performance of the heat pump system. Moreover, the energy consumption of the dryer for the NHPD method was more than the HPD method.

Comparison of Fenton process and adsorption method for treatment of industrial container and drum cleaning industry wastewater.

Science.gov (United States)

Güneş, Elçin; Çifçi, Deniz İzlen; Çelik, Suna Özden

2018-04-01

The present study aims to explore the characterization of industrial container and drum cleaning (ICDC) industry wastewater and treatment alternatives of this wastewater using Fenton and adsorption processes. Wastewater derived from ICDC industry is usually treated by chemical coagulation and biological treatment in Turkey and then discharged in a centralized wastewater treatment facility. It is required that the wastewater COD is below 1500 mg/L to treat in a centralized wastewater treatment facility. The wastewater samples were characterized for parameters of pH, conductivity, COD, BOD 5 , TSS, NH 3 -N, TN, TOC, TP, Cd, Cr, Cu, Fe, Ni, Pb, Zn, and Hg. Initial COD values were in the range of 11,300-14,200 mg/L. The optimum conditions for Fenton treatment were 35-40 g/L for H 2 O 2 , 2-5 g/L for Fe 2+ , and 13-36 for H 2 O 2 /Fe 2+ molar ratio. The optimum conditions of PAC doses and contact times in adsorption studies were 20-30 g/L and 5-12 h, respectively. Removal efficiencies of characterized parameters for the three samples were compared for both Fenton and adsorption processes under optimum conditions. The results suggest that these wastewaters are suitable for discharge to a centralized wastewater treatment plant.

CSER 00-006 Storage of Plutonium Residue Containers in 55 Gallon Drums at the PFP

Energy Technology Data Exchange (ETDEWEB)

DOBBIN, K.D.

2000-05-24

This criticality safety evaluation report (CSER) provides the required limit set and controls for safe transit and storage of these drums in the 234-5Z Building at the PFP. A mass limit of 200 g of plutonium or fissile equivalent per drum is acceptable

Granular flow in a rotating drum: Experiments and theory

Science.gov (United States)

Hung, C. Y.; Stark, C. P.; Capart, H.; Li, L.; Smith, B.; Grinspun, E.

2015-12-01

Erosion at the base of a debris flow fundamentally controls how large the flow will become and how far it will travel. Experimental observations of this important phenomenon are rather limited, and this lack has led theoretical treatments to making ad hoc assumptions about the basal process. In light of this, we carried out a combination of laboratory experiments and theoretical analysis of granular flow in a rotating drum, a canonical example of steady grain motion in which entrainment rates can be precisely controlled. Our main result is that basal sediment is entrained as the velocity profile adjusts to imbalance in the flow of kinetic energy.Our experimental apparatus consisted of a 40cm-diameter drum, 4cm-deep, half-filled with 2.3mm grains. Rotation rates varied from 1-70 rpm. We varied the effective scale by varying effective gravity from 1g to 70g on a geotechnical centrifuge. The field of grain motion was recorded using high-speed video and mapped using particle tracking velocimetry. In tandem we developed a depth-averaged theory using balance equations for mass, momentum and kinetic energy. We assumed a linearized GDR Midi granular rheology [da Cruz, 2005] and a Coulomb friction law along the sidewalls [Jop et al., 2005]. A scaling analysis of our equations yields a dimensionless "entrainment number" En, which neatly parametrizes the flow geometry in the drum for a wide range of variables, e.g., rotation rate and effective gravity. At low En, the flow profile is planar and kinetic energy is balanced locally in the flow layer. At high En, the flow profile is sigmoidal (yin-yang shaped) and the kinetic energy is dominated by longitudinal, streamwise transfer. We observe different scaling behavior under each of these flow regimes, e.g., between En and kinetic energy, surface slope and flow depth. Our theory correctly predicts their scaling exponents and the value of En at which the regime transition takes place. We are also able to make corrections for

Evaluation and mitigation of tritium memory in detritiation dryers

International Nuclear Information System (INIS)

Malara, C.; Ricapito, I.; Edwards, R.A.H.; Toci, F.

1999-01-01

In atmospheric detritiation, and other tritium processes, tritium is adsorbed on zeolites (molecular sieves) in the form of tritiated water. Regeneration removes almost all the physically adsorbed water, but a proportion remains permanently in the zeolite and binder structure as chemically bound water or hydroxyl groups. Exchange between adsorbed water and bound water means that tritiated water is retained in the structure after regeneration. At the end of its life, the zeolite therefore constitutes a tritiated waste. Furthermore, if an atmosphere detritiation dryer (ADD) gets highly contaminated from a tritium spill, retained tritium contaminates both the small amount of vapour leaving the bed during the next drying cycle, and the water produced in the subsequent regeneration. This report first describes experiments to measure the tritiated water retained in a 5A zeolite bed after standard regeneration treatments, and then investigates strategies to mitigate the effect: more thorough regeneration and isotope swamping or elution. The effect of zeolite ageing after thermal cycling is also seen. (orig.)

Reducing language to rhythm: Amazonian Bora drummed language exploits speech rhythm for long-distance communication

Science.gov (United States)

Seifart, Frank; Meyer, Julien; Grawunder, Sven; Dentel, Laure

2018-04-01

Many drum communication systems around the world transmit information by emulating tonal and rhythmic patterns of spoken languages in sequences of drumbeats. Their rhythmic characteristics, in particular, have not been systematically studied so far, although understanding them represents a rare occasion for providing an original insight into the basic units of speech rhythm as selected by natural speech practices directly based on beats. Here, we analyse a corpus of Bora drum communication from the northwest Amazon, which is nowadays endangered with extinction. We show that four rhythmic units are encoded in the length of pauses between beats. We argue that these units correspond to vowel-to-vowel intervals with different numbers of consonants and vowel lengths. By contrast, aligning beats with syllables, mora or only vowel length yields inconsistent results. Moreover, we also show that Bora drummed messages conventionally select rhythmically distinct markers to further distinguish words. The two phonological tones represented in drummed speech encode only few lexical contrasts. Rhythm thus appears to crucially contribute to the intelligibility of drummed Bora. Our study provides novel evidence for the role of rhythmic structures composed of vowel-to-vowel intervals in the complex puzzle concerning the redundancy and distinctiveness of acoustic features embedded in speech.

Sanitary condition of electrical hand dryers in toilets of shopping centres in Kraków

Directory of Open Access Journals (Sweden)

Anna Lenart-Boroń

2015-06-01

Full Text Available Introduction. Shopping habits have changed over the past several years and consumers choose shopping centres, where they can spend time and visit restaurants. People usually wash hands before meals, but toilets in shopping centres are visited by hundreds of users every day which makes their cleanliness questionable. Therefore, the aim of this study was to assess the sanitary condition of electrical hand dryers in toilets of the selected shopping centres in Kraków. Material and methods. Air was sampled at the outlet of electrical hand dryers and surface swabs of hand dryers were taken in toilets of five shopping centres. Air sampling was conducted using the MAS-100 impactor. The number of mesophilic bacteria, fungi, actinomycetes, staphylococci and Escherichia coli was determined. The results of air analyses were compared with the limits provided by the Polish Standards on air quality. Results. The number of microorganisms varied between the studied centres. In terms of mesophilic bacteria and fungi the air was unpolluted. The concentration of actinomycetes however significantly exceeded the limits set by the Polish Standards. Numerous Escherichia coli were found both in the air and in swabs in one of the centres. However the number of E. coli and staphylococci did not exceed the minimum infective dose. Conclusions. The studies showed high concentrations of airborne actinomycetes and staphylococci. Also the presence of E. coli in the air and swabs allows the conclusion that legal regulations for concentrations of airborne microorganisms are necessary to make people aware of this problem. However, it was found that using electrical hand dryers does not have impact on human health.

Modification of Indirect Solar Dryer for Simplicia Production

Science.gov (United States)

Purnomo, C. W.; Indarti, S.

2018-03-01

Simplicia is natural ingredient for herbal medicine that has been subjected to drying only. This study aims to develop an appropriate drying equipment to produce dried leaves of sambung nyawa (Gynura procumbens (Lour.) Merr.) or also called “longevity spinach”. Typical indirect solar drier was modified to be able to process more fresh leaves in order to speed up the production. The modification was done using double solar collector and wind powered ventilation. The double solar collector was applied in order to collect more solar energy for larger dimension of drying chamber, while the wind-ventilator was installed to provide forced convection of hot air flow inside the dryer. The drying kinetic including the drying constants were investigated using three common thin layer drying equations to model the drying behavior of the leaves. The moisture ratio (MR) depletion with respect to the drying time (t) of the leaves can be well represented by equation of MR=1.1732exp(-0.0993.t)-0.1732exp(-17.3871.t).

Experimental Method for Analyzing Friction Phenomenon Related to Drum Brake Squeal

Directory of Open Access Journals (Sweden)

J. GLIŠOVIĆ

2010-12-01

Full Text Available Automobile brakes have been intensively developed during past few decades, but the maximum motor’s power, that should amortized in vehicle brakes, has been significantly increased also. Most of the kinetic energy of the moving vehicles is transforming into heat through friction. But the small part of kinetic energy transforms into sound pressure and makes noise. Low frequency squeal of drum brakes is very intense and can lead to customers’ complain. The interaction between the brake system and the vehicle framework and suspension is often very substantial during occurrence of brake noise. Unfortunately, to solve this type of squeal problem is also difficult because of the large number of components involved. The other cause is attributed to self-excited vibration that is induced when the friction material has a negative slope in relation to the relative velocity. This paper illustrates an approach to experimental studies of drum brakes in road conditions in order to monitor changes in the coefficient of friction that can generate drum brake squeal at low frequencies.

Sustainable implementation of solar tunnel dryers, water heaters and cookers in Nepal

Energy Technology Data Exchange (ETDEWEB)

Kovacs, Peter [Danish Energy Management, DEM for Renewable Energy Project, REP, Dhobighat, Lalitpur (Nepal); Shrestha, Niraj; Shakya, Prajwal Raj [Renewable Energy Project, REP, Dhobighat, Lalitpur (Nepal); Pokharel, Govind [Alternative Energy Promotion Centre (AEPC), Lalitpur (Nepal)

2008-07-01

The Renewable Energy Project (REP) is a joint effort of the European Union and the Government of Nepal. Main objectives of the project are to create renewable energy infrastructure and services for the benefit of rural people in remote districts of Nepal. The REP will provide solar energy systems for public services in remote districts, as well as for income generating activities e.g. agro business and tourism. The REP focuses on the installation of institutional PV systems with a total capacity of 0.850 MWp. Concurrently, a number of solar thermal systems are being provided to community organizations (COs) in rural areas of Nepal. The priority applications for the solar thermal part are solar tunnel dryers for small industries drying vegetables. fruits and herbs, solar water heaters for community centers in trekking areas and large scale solar cookers in schools. The paper describes the Renewable Energy Project's implementation program for solar thermal technology and in particular the implications on design and usefulness of the solar tunnel dryer from on-site feasibility studies carried out by the project team. REP provides a framework for a sustainable implementation of these systems by carrying out the whole process from dissemination of information to demand collection, feasibility studies, design, procurement, commissioning and user training. Hand over of ownership will take place once the equipment is installed and successfully commissioned. Monitoring during the first year of operation should conclude the project. REP is co-funded by the European Union and the Government of Nepal. (orig.)

Improvement of Algorithms for Pressure Maintenance Systems in Drum-Separators of RBMK-1000 Reactors

Energy Technology Data Exchange (ETDEWEB)

Aleksakov, A. N., E-mail: yankovskiy.k@nikiet.ru; Yankovskiy, K. I. [JSC “N. A. Dollezhal Research and Development Institute of Power Engineering (NIKIET),” (Russian Federation); Dunaev, V. I.; Kushbasov, A. N. [JSC “Diakont,” (Russian Federation)

2015-05-15

The main tasks and challenges for pressure regulation in the drum-separators of RBMK-1000 reactors are described. New approaches to constructing algorithms for pressure control in drum-separators by electro-hydraulic turbine control systems are discussed. Results are provided from tests of the operation of modernized pressure regulators during fast transients with reductions in reactor power.

High speed rotary drum

Energy Technology Data Exchange (ETDEWEB)

Sagara, H

1970-03-25

A high speed rotary drum is disclosed in which the rotor vessel is a double-wall structure comprising an inner wave-shaped pipe inserted coaxially within an outer straight pipe, the object being to provide a strengthened composite light-weight structure. Since force induced axial deformation of the straight pipe and radial deformation of the corrugated pipe are small, the composite effectively resists external forces and, if the waves of the inner pipe are given a sufficient amplitude, the thickness of both pipes may be reduced to lower the overall weight. Thus high angular velocities can be obtained to separate U/sup 235/ from gaseous UF/sub 6/.

Use of Computational Fluid Dynamics for improving freeze-dryers design and process understanding. Part 1: Modelling the lyophilisation chamber.

Science.gov (United States)

Barresi, Antonello A; Rasetto, Valeria; Marchisio, Daniele L

2018-05-15

This manuscript shows how computational models, mainly based on Computational Fluid Dynamics (CFD), can be used to simulate different parts of an industrial freeze-drying equipment and to properly design them; in particular, the freeze-dryer chamber and the duct connecting the chamber with the condenser, with the valves and vanes eventually present are analysed in this work. In Part 1, it will be shown how CFD can be employed to improve specific designs, to perform geometry optimization, to evaluate different design choices and how it is useful to evaluate the effect on product drying and batch variance. Such an approach allows an in-depth process understanding and assessment of the critical aspects of lyophilisation. This can be done by running either steady-state or transient simulations with imposed sublimation rates or with multi-scale approaches. This methodology will be demonstrated on freeze-drying equipment of different sizes, investigating the influence of the equipment geometry and shelf inter-distance. The effect of valve type (butterfly and mushroom) and shape on duct conductance and critical flow conditions will be instead investigated in Part 2. Copyright © 2018. Published by Elsevier B.V.

The determination of carbon dioxide concentration using atmospheric pressure ionization mass spectrometry/isotopic dilution and errors in concentration measurements caused by dryers.

Science.gov (United States)

DeLacy, Brendan G; Bandy, Alan R

2008-01-01

An atmospheric pressure ionization mass spectrometry/isotopically labeled standard (APIMS/ILS) method has been developed for the determination of carbon dioxide (CO(2)) concentration. Descriptions of the instrumental components, the ionization chemistry, and the statistics associated with the analytical method are provided. This method represents an alternative to the nondispersive infrared (NDIR) technique, which is currently used in the atmospheric community to determine atmospheric CO(2) concentrations. The APIMS/ILS and NDIR methods exhibit a decreased sensitivity for CO(2) in the presence of water vapor. Therefore, dryers such as a nafion dryer are used to remove water before detection. The APIMS/ILS method measures mixing ratios and demonstrates linearity and range in the presence or absence of a dryer. The NDIR technique, on the other hand, measures molar concentrations. The second half of this paper describes errors in molar concentration measurements that are caused by drying. An equation describing the errors was derived from the ideal gas law, the conservation of mass, and Dalton's Law. The purpose of this derivation was to quantify errors in the NDIR technique that are caused by drying. Laboratory experiments were conducted to verify the errors created solely by the dryer in CO(2) concentration measurements post-dryer. The laboratory experiments verified the theoretically predicted errors in the derived equations. There are numerous references in the literature that describe the use of a dryer in conjunction with the NDIR technique. However, these references do not address the errors that are caused by drying.

Determination of the germanium detector efficiency for measurements of the radionuclide activity contained in a radioactive waste drum

International Nuclear Information System (INIS)

Rodenas, J.; Gallardo, S.; Ballester, S.; Hoyler, F.

2006-01-01

One of the features in the characterization of a drum containing radioactive wastes is to verify the activity of radionuclides contained in the drum. An H.P. Ge detector can be used for this measurement. However, it is necessary to perform an efficiency calibration for all geometries involved. In the framework of a joint project between the Departamento de Ingenieria Quimica y Nuclear (Universidad Politecnica de Valencia, Spain) and the Fachbereich Angewandte Naturwissenschaften und Technik (Fachhochschule Aachen, Abteilung Julich, Germany), different configurations for a drum containing radioactive sources have been implemented in the laboratory. A cylindrical drum of 850 mm height, a diameter equal to 560 mm and 3 mm of steel thickness has been used in the experimental measurements. The drum contains a clay ceramic matrix whose chemical composition is 55% SiO 2 , 40% of Al 2 O 3 and 5% of TiO 2 . Several vertical PVC tubes having a diameter of 30 mm are inserted in the drum at different distances from the central axis. In the experiment, a pack of point sources with 133 Ba, 60 Co and 137 Cs is introduced into each one of the tubes. A ring-shape distributed source is generated by rotating the drum around its axis during the measurement. The detector efficiency is determined experimentally for these configurations. On the other hand, a Monte Carlo model, using the M.C.N.P. code, has been developed to simulate the drum, the clay matrix and the PVC tubes. The effect of the drum spinning has been reproduced simulating a ring source with different diameters. The model also includes detailed detector geometry. Using this Monte Carlo model, the detector efficiency is calculated for each configuration implemented in the laboratory. Comparison of results from Monte Carlo simulation and experimental measurements should permit the validation of the M.C.N.P. model. Consequently it will be possible to obtain efficiency curves without experimental measurements. Therefore, these

Heat transfer to immersed horizontal tubes in gas fluidized bed dryers

Energy Technology Data Exchange (ETDEWEB)

Jonassen, Ola

1999-07-01

The main objective of this study was to construct heat pump fluidized bed dryers of the FHT type with improved dewatering capacity for a given size of the dryer. The use of heat exchangers immersed in the fluidized bed drying chambers is an important part of the FHT (Fluidized Bed High Temperature Heat Pump Dryer) concept. A pilot plant FHT dryer was built and successfully tested on fish meal raw material and seaweed. The plant included two fluidized bed drying chambers with immersed heat exchangers. The gain in water vapor of the drying air through the chambers was increased up to four times that of adiabatic drying. The energy saving concept was retained as a SMER ratio of 3.5 to 4.7 was measured in the same tests. Therefore optimization of the immersed heat exchangers was considered the most important single objective for this work. The optimization study of the heat exchangers was confined to the actual operating conditions for the dryers using: (1) Bubbling gas fluidized beds were used, (2) air as the only type of fluidizing gas,(3) beds at atmospheric pressure, (4) bed temperatures below 100 {sup o}C, (5) fluidized particles of Geldart classes B and D, (6) horizontal tube banks for the immersed heat exchanger and the influence of radiation heat transfer was ignored. The heat transfer study was confined to the fluidized bed side of the heat exchanger surface. It was concluded early in this work that the bubbles play a major role in generating the particle circulation inside the bed and hence also in heat transfer. Publications describing the most important bubble induced mechanisms contributing to high rates of heat transfer were found to be limited. Therefore the first part of this study was aimed at establishing a method for locating and measuring the size and rise velocity of bubbles inside the bed. The method established through this work using differential pressure measurements from two static pressure probes was used later in the study of heat transfer

Design of temperature detection device for drum of belt conveyor

Science.gov (United States)

Zhang, Li; He, Rongjun

2018-03-01

For difficult wiring and big measuring error existed in the traditional temperature detection method for drum of belt conveyor, a temperature detection device for drum of belt conveyor based on Radio Frequency(RF) communication is designed. In the device, detection terminal can collect temperature data through tire pressure sensor chip SP370 which integrates temperature detection and RF emission. The receiving terminal which is composed of RF receiver chip and microcontroller receives the temperature data and sends it to Controller Area Network(CAN) bus. The test results show that the device meets requirements of field application with measuring error ±3.73 ° and single button battery can provide continuous current for the detection terminal over 1.5 years.

Results of the gamma-neutron mapper performance test on 55-gallon drums at the RWMC

International Nuclear Information System (INIS)

Gehrke, R.J.; Lawrence, R.S.; Roybal, L.G.; Svoboda, J.M.; Harker, D.J.; Thompson, D.N.; Carpenter, M.V.; Josten, N.E.

1995-07-01

The primary purpose of the gamma-neutron mapper (G at sign) is to provide accurate and quantitative spatial information of the gamma-ray and neutron radiation fields as a function of position about the excavation of a radioactive waste site. The GNM is designed to operate remotely and can be delivered to any point on an excavation by the robotic gantry crane developed by the dig-face project at the Idaho National Engineering Laboratory (INEL). It can also be easily adapted to other delivery systems. The GNM can be deployed over a waste site at a predetermined scan rate and has sufficient accuracy to identify and quantify radioactive contaminants of importance. The results reported herein are from a performance test conducted at the Transuranic Storage Area, Building 628, of the Radioactive Waste Management Complex located at the INEL. This building is an active interim-storage area for 55-gal drums of transuranic waste from the Department of Energy's Rocky Flats Plant. The performance test consisted of scanning a stack of drums five high by five wide. Prior to the test, radiation fields were measured by a health physicist at the center of the drums and ranged from 0.5 mR/h to 35 mR/h. Scans of the drums using the GNM were taken at standoff distances from the vertical drum stack of 15 cm, 30 cm, 45 cm, and 90 cm. Data were acquired at scan speeds of 7.5 cm/s and 15 cm/s. The results of these scans and a comparison of these results with the manifests of these drums are compared and discussed

ANALISIS KELAYAKAN TEKNIS DAN FINANSIAL DARI INVESTASI PENGADAAN TRAY DRYER BERBAHAN BAKAR BIOMASSA PADA USAHA ARANG TEMPURUNG KELAPA BERBASIS EKSPOR (Studi Kasus di Tropica Nucifera Industry – Yogyakarta

Directory of Open Access Journals (Sweden)

Fanny Widadie

2013-11-01

Full Text Available The purpose of the study is to assess the technical and financial feasibility of procurement investment Tray Dryer fueled biomass to operations of coconut shell charcoal briquette in PT. Tropica Nucifera Industry. The result showed that investment-Tray Dryer on cocnut shell charcoal briquette bussiness was highly feasibile both the technical and financial aspects. The technical aspect was seen that the quantity-production capabilities of coconut shell charcoal briquettes using a dryer-Tray Dryer could be increased 15 percent compared the previous consdition-used of solar energy. While the quality of the charcoal briquettes produced from Tray Dryer was a much butter quality, moisture content (6.39%; ash (2.65%; carbon-bound (85.83%, compared to using sunlight, water content (15.89; ash (2.57% and carbon-bound (77.32%.The financial aspects of procurement Tray Dryer investment that its value was more feasible than previous, nothing Tray Dryer. Coconut shell charcoal briquet enterprises without using Tray Dryer was feasible to be done with NPV 1,058,928.12, IRR 63%, Payback Period 1 year and 9 moths, Net B/C 2.25 and analysis of swicthcing value reached 20 percent. And after the business using Tray Drayer, the financial analysis was much more feasible with NPV 2,285,500,498.12, IRR 113%, Payback Period 11 months, Net B/C 3.5 and analysis of switching value reached 50 percent.

Experimental investigation and thermodynamic performance analysis of a solar dryer using an evacuated-tube air collector

International Nuclear Information System (INIS)

Lamnatou, Chr.; Papanicolaou, E.; Belessiotis, V.; Kyriakis, N.

2012-01-01

Highlights: ► We evaluate an evacuated-tube solar air collector and use it to develop a novel dryer. ► Apple, carrot and apricot thin-layer drying experiments are conducted. ► Best overall fitting among several available thin-layer drying models is pursued. ► Thermodynamic analysis yields optimal collector area, energy utilization/exergy loss. ► The proposed dryer has a capacity for drying larger quantities of products. -- Abstract: The present work presents a thermodynamic performance analysis of a solar dryer with an evacuated-tube collector. Drying experiments for apples, carrots and apricots were conducted, after a preliminary stage of the investigation which included measurements for the determination of the collector efficiency. These results showed that the warm outlet air of the collector attains temperature levels suitable for drying of agricultural products without the need of preheating. Thus, the present collector was used as the heat source for a drying chamber in the frame of the development of a novel, convective, indirect solar dryer; given the fact that in the literature there are only a few studies about this type of collectors in conjunction with solar drying applications. Thin-layer drying models were fitted to the experimental drying curves, including the recent model of Diamante et al. which showed good correlation coefficients for all the tested products. Drying parameters such as moisture ratio and drying rates were calculated. Furthermore, an energetic/exergetic analysis of the dryer was also conducted and performance coefficients such as pick-up and exergy efficiencies, energy utilization ratio, exergy losses were determined for several configurations such as single and double-trays and several drying air velocities. On the other hand, an optimal collector surface area study was conducted, based on laws for minimum entropy generation. Design parameters such as optimum collector area were determined based on the minimum entropy

Experimental study of regenerative desiccant integrated solar dryer with and without reflective mirror

Energy Technology Data Exchange (ETDEWEB)

Shanmugam, V. [Department of Mechanical Engineering, Sathyabama University, Chennai, 600 119 (India); Natarajan, E. [Institute for Energy Studies, College of Engineering, Anna University, Chennai, 600 025 (India)

2007-06-15

An indirect forced convection with desiccant integrated solar dryer has been built and tested. The main parts are: a flat plate solar air collector, a drying chamber, desiccant bed and a centrifugal blower. The system is operated in two modes, sunshine hours and off sunshine hours. During sun shine hours the hot air from the flat plate collector is forced to the drying chamber for drying the product and simultaneously the desiccant bed receives solar radiation directly and through the reflected mirror. In the off sunshine hours, the dryer is operated by circulating the air inside the drying chamber through the desiccant bed by a reversible fan. The dryer is used to dry 20 kg of green peas and pineapple slices. Drying experiments were conducted with and without the integration of desiccant unit. The effect of reflective mirror on the drying potential of desiccant unit was also investigated. With the inclusion of reflective mirror, the drying potential of the desiccant material is increased by 20% and the drying time is reduced. The drying efficiency of the system varies between 43% and 55% and the pick-up efficiency varies between 20% and 60%, respectively. Approximately in all the drying experiments 60% of moisture is removed by air heated using solar energy and the remainder by the desiccant. The inclusion of reflective mirror on the desiccant bed makes faster regeneration of the desiccant material. (author)

PADDY DRYING IN MIXED ADSORPTION DRYER WITH ZEOLITE: DRYING RATE AND TIME ESTIMATION

Directory of Open Access Journals (Sweden)

Mochammad Djaeni

2013-11-01

Full Text Available Recently, the main problem of the rice stock and distribution in Indonesia is the quality degradation as indicated in unpleasant odor (smelly, stained, yellowness, and high percentage of broken rice. This is due to the low of paddy quality dried by from either direct sunlight or conventional fluidized bed dryer. As a result, the paddy cracks and breaks easily during milling in which causes the storage life being shorter as the enzymatic degradation by germ or fungi occurs. Air dehumidified with zeolite at drying medium temperature is potential to improve the quality of paddy. Zeolite is a material having high affinity to water vapor. In this case, the paddy and zeolite was mixed and fluidized with the air. The air will evaporate water from paddy, and at same time, the zeolite will adsorb water from air. Hence, the humidity of dryer can be kept low in which improves the driving force for drying. This work discusses the effect of presence of zeolite in the dryer, operational drying temperature, air velocity and relative humidity on drying rate of paddy. The results showed that increasing of zeolite as well as operational temperature increased the drying rate. In addition, using the model, the air dehumidification with zeolite and increase of air velocity can speed up drying time significantly at operational temperature below 80oC. This condition is very suitable for paddy drying since the quality degradation can be avoided.

Saving energy. [Metal Coating With Infrared Dryers

Energy Technology Data Exchange (ETDEWEB)

Schmid, K

1981-01-01

One way of saving energy in metal coating is by using electrically heated infrared dryers with medium-wave radiation (2 to 3 ..mu..m). The absorbing capacity of varnishes and plastic coatings is >90% in this range so that the radiation energy is almost completely transformed into heat. Medium-wave radiation sources have a much higher service life than short-wave sources (30.000 hours of operation) and do not require cooling; compared with long-wave sources, they have a higher heat transfer and thus much shorter drying times. The main fields of application, a cost example, and practical examples among the customers of Messrs. Eisenmann are presented.

Design and Performance Evaluation of a Solar Assisted Heat Pump Dryer Integrated with Biomass Furnace for Red Chilli

Directory of Open Access Journals (Sweden)

M. Yahya

2016-01-01

Full Text Available The performance of a solar assisted heat pump dryer integrated with biomass furnace has been designed and evaluated for drying red chillies, and drying kinetics of red chillies were evaluated. The red chillies were dried from 22 kg with moisture content of 4.26 db to moisture content of 0.08 db which needed 11 hours, with the average drying chamber temperature, drying chamber relative humidity, and an air mass flow rate of 70.5°C, 10.1%, and 0.124 kg/s, respectively, while the open sun drying needed 62 hours. Compared to open sun drying, this dryer yielded 82% saving in drying time. The drying rate, the specific moisture extraction rate, and thermal efficiency of the dryer were estimated in average to be about 1.57 kg/h, 0.14 kg/kWh, and 9.03%, respectively. Three mathematical models, the Newton, Henderson-Pabis, and Page models, were fitted to the experimental data on red chillies dried by solar assisted heat pump dryer integrated with biomass furnace and open sun drying. The performance of these models was evaluated by comparing the coefficient of determination (R2, mean bias error (MBE, and root mean-square error (RMSE. The Page model gave the best results for representing drying kinetics of red chillies.

Modelling of hot air chamber designs of a continuous flow grain dryer

DEFF Research Database (Denmark)

Kjær, Lotte Strange; Poulsen, Mathias; Sørensen, Kim

2018-01-01

The pressure loss, flow distribution and temperature distribution of a number of designs of the hot air chamber in a continuous flow grain dryer, were investigated using CFD. The flow in the dryer was considered as steady state, compressible and turbulent. It is essential that the grain...... is uniformly dried as uneven drying can result in damage to the end-product during storage. The original commercial design was modified with new guide vanes at the inlets to reduce the pressure loss and to ensure a uniform flow to the line burner in the hot air chamber. The new guide vane design resulted...... in a 10% reduction in pressure loss and a γ-value of 0.804. Various design changes of the hot air chamber were analysed in terms of pressure loss and temperature distribution with the aim of a temperature variation of 5 K at the outlet ducts. An obstruction design was analysed, which improved mixing...

Design aspects of integrated compact thermal storage system for solar dryer applications

International Nuclear Information System (INIS)

Rajaraman, R.; Velraj, R.; Renganarayanan, S.

2000-01-01

Solar energy is an excellent source for drying of crops, fruits, vegetables and other agricultural and forest products. Though the availability of solar energy is plenty, it is time dependent in nature. The energy need for some applications is also time dependent, but in a different pattern and phase from the solar energy supply. This implies that the solar dryer should be integrated with an efficient thermal storage system to match the time-dependent supply and end-use requirements. Based on the studies carried out on Latent Heat Thermal Storage (LHTS) Systems, it is observed that when air is used as the heat transfer fluid in LHTS system, nearly uniform surface heat flux can be achieved. Hence the LHTS systems are most suitable for air based solar drying applications. In the present work some major conclusions arrived from the investigations on LHTS systems and the design considerations for the integrated latent heat thermal storage for the solar dryer are reported. (Author)

Product development of pumpkin tablet

Directory of Open Access Journals (Sweden)

Kamgoed, T.

2007-05-01

Full Text Available The development of pumpkin tablet was studied and the drying conditions of pumpkin using a double drum dryer were optimized. The study factors were drying agents (maltodextrin D.E.13-16 andtapioca flour at different levels (3 and 5%, drying temperatures (130 and 140oC and drum dryer speeds (4 and 5 rpm. The results showed that the optimal conditions were using 3% maltodextrin D.E.13-16, dryingtemperature of 130oC and drum dryer speed of 4 rpm. The moisture, fat, bulk density, reducing sugars and granulometric retention of the obtained pumpkin powder were 3.39%, 1.42%, 1.004 g/ml, 12.63% and 0.67%, respectively and L*, a* and b* values were 73.85, -0.60 and 35.23, respectively. A study of suitable amount of icing sugar using different contents for tablet production (0, 10, 20, 30 and 40% was performedand showed that using 20% icing sugar was the most acceptable. The obtained pumpkin tablet was subjected to chemical, physical and microbiological analysis. The ash, moisture, protein, fat, fiber and carbohydratecontents were 1.87, 3.60, 3.34, 1.00, 2.26 and 87.99%, respectively. The reducing sugars and β-carotene contents were 5.44±0.61% and 3.79±0.57 mg/100g, respectively. The Aw, hardness and solubility were 0.56,3.25 kgf and 25.00 %, respectively. The L*, a* and b* values were 79.85, 0.28 and 23.64, respectively. The total microbial count and the yeast and mould count were <10 CFU/g. The shelf life of the pumpkin tabletwas at least 4 months at room temperature (35±2oC.

Solar dryers for a non-polluting removal of sewage sludge; Solartrockner fuer eine umweltfreundliche Klaerschlammentsorgung

Energy Technology Data Exchange (ETDEWEB)

Kos, Manfred [Lenze, Hameln (Germany)

2011-06-15

The acceptance of solar drying technology is depending on the quality of the produced dry goods. On local markets as well as for the export market dryed products can only compete if they can meet the quality standards of the food processing industry and consumers. A high added value for operators of solar dryers especially from developing countries can only be achieved if the goods can be exported. Dried sewage sludge shows to have an energy density corresponding to brown coal, burns however carbon dioxide neutrally compared with fossil fuels and grows continuously in water treatment plants on the outskirts of cities. (GL)

Criticality safety study of Pu contaminated carbon waste stored in 100 L steel drums

International Nuclear Information System (INIS)

Anno, J.; Simonneau, M.

1995-01-01

The notion of the minimum critical areal density (D minca ) used to ensure the Criticality-Safety of poor solid waste is recalled with its deficiencies. D minca is assumed constant, independent of the fissile material concentration. This assumption is only true for unreflected mediums. Corrective factors are established. Furthermore, the usual norm of the Pu-H 2 O, which is 0.20 g/cm 2 , (concrete reflected) is greater than that for other mediums, such as Pu contaminated graphite waste (Pu-C), which is 0.036 g/cm 2 . D minca calculated on infinite slabs is confirmed by calculations on infinite planar multilayers arrays of 100 l cubical waste drums. Moreover, d minca increases linearly with the steel thickness of the drums' walls and goes up to 0.17 g/cm 2 for 0.105 cm of steel. The safety analysis on a real storage case takes into account the limited amount of Pu (100 g) and C (100 kg), the minimum thickness of 0.07 cm of drums' steel, their geometrical arrangement, the heterogeneity and size of contamination and the occurrence of neutronic poison (N and Cl) in the waste. Because of these parameters, the Keff are very less than 0.95 and the taken norm of 0.1 g/cm 2 for the Pu-C waste is fulfilled. Finally, it is demonstrated that the mixing of Pu-C waste drums and Pu-H 2 O wastes drums is allowed. (authors). 14 refs., 5 figs., 6 tabs

40 CFR 264.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

Science.gov (United States)

2010-07-01

... HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Landfills § 264.316 Disposal of small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste in overpacked... hazardous waste in overpacked drums (lab packs). 264.316 Section 264.316 Protection of Environment...

40 CFR 265.316 - Disposal of small containers of hazardous waste in overpacked drums (lab packs).

Science.gov (United States)

2010-07-01

... OPERATORS OF HAZARDOUS WASTE TREATMENT, STORAGE, AND DISPOSAL FACILITIES Landfills § 265.316 Disposal of small containers of hazardous waste in overpacked drums (lab packs). Small containers of hazardous waste... hazardous waste in overpacked drums (lab packs). 265.316 Section 265.316 Protection of Environment...

76 FR 22453 - Energy Conservation Program: Energy Conservation Standards for Residential Clothes Dryers and...

Science.gov (United States)

2011-04-21

... Mode and Off Mode b. Automatic Cycle Termination c. Ventless Clothes Dryers d. Consumer Usage Habits e... as cooling capacity in British thermal units (Btu) per hour (h) divided by electrical input power in...

Improved Processing and Marketing of Healthy Fish Products in ...

International Development Research Centre (IDRC) Digital Library (Canada)

Improved Processing and Marketing of Healthy Fish Products in Inland Fisheries in Malawi (CultiAF). This project aims ... They will test different pre-drying methods: -no pre-drying treatment -parboiling -smoking -brining Solar dryer and business model testing Researchers will assess the solar dryers' economic performance.

Feeling the beat where it counts: fostering multi-limb rhythm skills with the haptic drum kit

NARCIS (Netherlands)

Holland, S.; Bouwer, A.J.; Dalgleish, M.; Hurtig, T.M.

2010-01-01

This paper introduces a tool known as the Haptic Drum Kit, which employs four computer-controlled vibrotactile devices, one attached to each wrist and ankle. In the applications discussed here, haptic pulses are used to guide the playing, on a drum kit, of rhythmic patterns that require multi-limb

CT examination of radwaste drums

International Nuclear Information System (INIS)

Duwe, R.; Jansen, P.

1988-01-01

In order to garantee safe operation of the waste disposal site it is inevitable for the operator to know the radioactive inventory as well as the physical and chemical properties of the conditioned waste. The declarations of the waste producers describing the type, amount and conditioning of the wastes are taken as a basis for specifications of waste forms. The aim of the work till now was to install simple measuring desk for emission computed tomography in order to count γ-activity levels in drums, and to detect density distributions by transmission computed tomography. (orig.) [de

Fault Diagnosis of Demountable Disk-Drum Aero-Engine Rotor Using Customized Multiwavelet Method

Directory of Open Access Journals (Sweden)

Jinglong Chen

2015-10-01

Full Text Available The demountable disk-drum aero-engine rotor is an important piece of equipment that greatly impacts the safe operation of aircraft. However, assembly looseness or crack fault has led to several unscheduled breakdowns and serious accidents. Thus, condition monitoring and fault diagnosis technique are required for identifying abnormal conditions. Customized ensemble multiwavelet method for aero-engine rotor condition identification, using measured vibration data, is developed in this paper. First, customized multiwavelet basis function with strong adaptivity is constructed via symmetric multiwavelet lifting scheme. Then vibration signal is processed by customized ensemble multiwavelet transform. Next, normalized information entropy of multiwavelet decomposition coefficients is computed to directly reflect and evaluate the condition. The proposed approach is first applied to fault detection of an experimental aero-engine rotor. Finally, the proposed approach is used in an engineering application, where it successfully identified the crack fault of a demountable disk-drum aero-engine rotor. The results show that the proposed method possesses excellent performance in fault detection of aero-engine rotor. Moreover, the robustness of the multiwavelet method against noise is also tested and verified by simulation and field experiments.

Controlling in situ crystallization of pharmaceutical particles within the spray dryer.

Science.gov (United States)

Woo, Meng Wai; Lee, May Ginn; Shakiba, Soroush; Mansouri, Shahnaz

2017-11-01

Simultaneous solidification and in situ crystallization (or partial crystallization) of droplets within the drying chamber are commonly encountered in the spray drying of pharmaceuticals. The crystallinity developed will determine the functionality of the powder and its stability during storage. This review discusses strategies that can be used to control the in situ crystallization process. Areas covered: The premise of the strategies discussed focuses on the manipulation of the droplet drying rate relative to the timescale of crystallization. This can be undertaken by the control of the spray drying operation, by the use of volatile materials and by the inclusion of additives. Several predictive approaches for in situ crystallization control and new spray dryer configuration strategies are further discussed. Expert opinion: Most reports, hitherto, have focused on the crystallinity of the spray dried material or the development of crystallinity during storage. More mechanistic understanding of the in situ crystallization process during spray drying is required to guide product formulation trials. The key challenge will be in adapting the mechanistic approach to the myriad possible formulations in the pharmaceutical industry.

Steam drum level dynamics in a multiple loop natural circulation system of a pressure-tube type boiling water reactor

International Nuclear Information System (INIS)

Jain, Vikas; Kulkarni, P.P.; Nayak, A.K.; Vijayan, P.K.; Saha, D.; Sinha, R.K.

2011-01-01

Highlights: → We have highlighted the problem of drum level dynamics in a multiple loop type NC system using RELAP5 code. → The need of interconnections in steam and liquid spaces close to drum is established. → The steam space interconnections equalize pressure and liquid space interconnections equalize level. → With this scheme, the system can withstand anomalous conditions. → However, the controller is found to be inevitable for inventory balance. - Abstract: Advanced Heavy Water Reactor (AHWR) is a pressure tube type boiling water reactor employing natural circulation as the mode of heat removal under all the operating conditions. Main heat transport system (MHTS) of AHWR is essentially a multi-loop natural circulation system with all the loops connected to each other. Each loop of MHTS has a steam drum that provides for gravity based steam-water separation. Steam drum level is a very critical parameter especially in multi-loop natural circulation systems as large departures from the set point may lead to ineffective separation of steam-water or may affect the driving head. However, such a system is susceptible to steam drum level anomalies under postulated asymmetrical operating conditions among the different quadrants of the core like feedwater flow distribution anomaly among the steam drums or power anomaly among the core quadrants. Analyses were carried out to probe such scenarios and unravel the underlying dynamics of steam drum level using system code RELAP5/Mod3.2. In addition, a scheme to obviate such problem in a passive manner without dependence on level controller was examined. It was concluded that steam drums need to be connected in the liquid as well as steam space to make the system tolerant to asymmetrical operating conditions.

Evaluation of an industrial gas-fired IR dryer; Utvaerdering av en industriell gaseldad IR-straalare

Energy Technology Data Exchange (ETDEWEB)

Stenstroem, S; Hermodsson, S

1994-11-01

The IR dryer is used in a paper making machine to dry the paper web after it has been coated with a surface layer. In part 1 of the project a mathematical model have been developed, capable of calculating the radiation intensity and other energy flows in the dryer. In part 2 of the project, measurements have been made on the IR radiator mounted in the paper making machine. The calculation model shows the efficiency of the radiator to 39% at full power and 35% at half power. The direct measurements were made at half power and gave an efficiency of 31% for new radiators and 28% for old ones. The conclusion is that the calculation model values corresponds very well compared with direct measurements.

A prototype of radioactive waste drum monitor by non-destructive assays using gamma spectrometry

International Nuclear Information System (INIS)

Thanh, Tran Thien; Trang, Hoang Thi Kieu; Chuong, Huynh Dinh; Nguyen, Vo Hoang; Tran, Le Bao; Tam, Hoang Duc; Tao, Chau Van

2016-01-01

In this work, segmented gamma scanning and the gamma emission tomography were used to locate unknown sources in a radioactive waste drum. The simulated detector response function and full energy peak efficiency are compared to corresponding experimental data and show about 5.3% difference for an energy ranging from 81 keV to 1332.5 keV for point sources. Computation of the corresponding activity is in good agreement with the true values. - Highlights: • Segmented gamma scanning and gamma emission tomography are used to locate point source in waste drums. • The PENELOPE software is used to compute the detection efficiency of the localized point source in the waste drum. • The activity of "1"3"7Cs and "6"0Co point source could be determined with an accuracy better than 10% for air and sand matrices.

Analysis and Testing of a Natural Convection Solar Dryer for the Tropics

Directory of Open Access Journals (Sweden)

A. O. Adelaja

2013-01-01

Full Text Available Solar dryers are imperative for the tropical and sub-Saharan African countries, which are faced with the duo challenges of inadequate electrical energy supply, which has severely limited the application of conventional refrigeration as a means of preservation of agricultural produce, and the need to make produce competitive in the international market. In this study, a cost-effective natural convection solar dryer was developed; the thermal and drying analyses were done and tested to obtain some performance evaluation parameters for the system in order to examine its efficiency and effectiveness by drying some plantain fillets. The collector and system efficiencies are found to be 46.4% and 78.73%, respectively, while a percentage moisture removal of 77.5% was achieved at the 20th hour in order to give final moisture contents of 15.75% in the product, which still maintained its integrity. With a cost of about $195.00, it has been affordable for the small- and medium-scale enterprises as well as for private use in domestic applications.

Preliminary minimum detectable limit measurements in 208-L drums for selected actinide isotopes in mock-waste matrices

International Nuclear Information System (INIS)

Camp, D.C.; Wang, Tzu-Fang; Martz, H.E.

1992-01-01

Preliminary minimum detectable levels (MDLS) of selected actinide isotopes have been determined in full-scale, 55-gallon drums filled with a range of mock-waste materials from combustibles (0.14 g/CM 3 ) to sand (1.7 g/CM 3 ). Measurements were recorded from 100 to 10,000 seconds with selected actinide sources located in these drums at an edge position, on the center axis of a drum and midway between these two positions. Measurements were also made with a 166 Ho source to evaluate the attenuation of these mock-matrix materials as a function of energy. By knowing where the source activity is located within a drum, our preliminary results show that a simply collimated 90% HPGE detector can differentiate between TRU (>100 nCi/g) and LLW amounts of 239 Pu in only 100s of measurement time and with sufficient accuracy in both low and medium density, low Z materials. Other actinides measured so far include 235 U, 241 Am, and 244 Cm. These measurements begin to establish the probable MDLs achievable in the nondestructive assays of real waste drums when using active and passive CT. How future measurements may differ from these preliminary measurements is also discussed

A maximum power point tracking algorithm for buoy-rope-drum wave energy converters

Science.gov (United States)

Wang, J. Q.; Zhang, X. C.; Zhou, Y.; Cui, Z. C.; Zhu, L. S.

2016-08-01

The maximum power point tracking control is the key link to improve the energy conversion efficiency of wave energy converters (WEC). This paper presents a novel variable step size Perturb and Observe maximum power point tracking algorithm with a power classification standard for control of a buoy-rope-drum WEC. The algorithm and simulation model of the buoy-rope-drum WEC are presented in details, as well as simulation experiment results. The results show that the algorithm tracks the maximum power point of the WEC fast and accurately.

Radiological analyses of intermediate and low level supercompacted waste drums by VQAD code

International Nuclear Information System (INIS)

Bace, M.; Trontl, K.; Gergeta, K.

2004-01-01

In order to increase the possibilities of the QAD-CGGP code, as well as to make the code more user friendly, modifications of the code have been performed. A general multisource option has been introduced into the code and a user friendly environment has been created through a Graphical User Interface. The improved version of the code has been used to calculate gamma dose rates of a single supercompacted waste drum and a pair of supercompacted waste drums. The results of the calculation were compared with the standard QAD-CGGP results. (author)

Demonstration test on manufacturing 200 l drum inner shielding material for recycling of reactor operating metal scrap

International Nuclear Information System (INIS)

Umemura, A.; Kimura, K.; Ueno, H.

1993-01-01

Low-level reactor wastes should be safely recycled considering those resource values, the reduction of waste disposal volume and environmental effects. The reasonable recycling system of reactor operating metal scrap has been studied and it was concluded that the 200 liter drum inner shielding material is a very promising product for recycling within the nuclear industry. The drum inner shielding material does not require high quality and so it is expected to be easily manufactured by melting and casting from roughly sorted scrap metals. This means that the economical scrap metal recycling system can be achieved by introducing it. Furthermore its use will ensure safety because of being contained in a drum. In order to realize this recycling system with the drum inner shielding material, the demonstration test program is being conducted. The construction of the test facility, which consists of a melting and refining furnace, a casting apparatus, a machining apparatus etc., was finishing in September, 1992

The design of a mechanical referencing system for the rear drum of the Longwall Shearer Coal Miner

Science.gov (United States)

Jones, E. W.; Yang, T. C. H.

1981-01-01

The design of two systems which reference the position of a longwall shearer coal miner to the mine roof of the present cut and of the last cut are presented. This system is part of an automation system that will guide the rear cutting drum in such a manner that the total depth of cut remains constant even though the front drum may be following an undulating roof profile. The rear drum referencing mechanism continually monitors the distance from the mine roof to the floor for the present cut. This system provides a signal to control a constant depth of cut. The last cut follower mechanism continually monitors the distance from the mine roof of the prior cut to the cutting drum. This latter system provides a signal to minimize the step height in the roof between cuts. The dynamic response of this hydraulic-pneumatic and mechanical system is analyzed to determine accumulator size and precharge pressure.

Measurement of VOC permeability of polymer bags and VOC solubility in polyethylene drum liner

International Nuclear Information System (INIS)

Liekhus, K.J.; Peterson, E.S.

1995-03-01

A test program conducted at the Idaho National Engineering Laboratory (INEL) investigated the use of a transport model to estimate the volatile organic compound (VOC) concentration in the void volume of a waste drum. Unsteady-state VOC transport model equations account for VOC permeation of polymer bags, VOC diffusion across openings in layers of confinement, and VOC solubility in a polyethylene drum liner. In support of this program, the VOC permeability of polymer bags and VOC equilibrium concentration in a polyethylene drum liner were measured for nine VOCs. The VOCs used in experiments were dichloromethane, carbon tetrachloride, cyclohexane, toluene, 1,1,1-trichloroethane, methanol, 1,1,2-trichloro-1,2,2-trifluoroethane (Freon-113), trichloroethylene, and p-xylene. The experimental results of these measurements as well as a method of estimating both parameters in the absence of experimental data are described in this report

Energy and rice quality aspects during drying of freshly harvested paddy with industrial inclined bed dryer

International Nuclear Information System (INIS)

Sarker, M.S.H.; Ibrahim, M. Nordin; Ab. Aziz, N.; Mohd. Salleh, P.

2014-01-01

Highlights: • We presented performance evaluation approach for industrial inclined bed paddy dryer. • Specific electrical energy consumption was 1.44–1.95 MJ/kg water evaporated. • Specific thermal energy consumption was 2.77–3.47 MJ/kg water evaporated. • Dryer yielded 1–4% higher head rice at drying temperature of 38–39 °C than 41–42 °C. • Dryers should be operated at 38–39 °C for 1–4% higher head rice at reasonable energy. - Abstract: The performance evaluation of any industrial dryer regarding energy consumption and product quality should be assessed to check its present status and to suggest for further efficient operation. An investigation was carried out to evaluate the impact of drying temperature and air flow on energy consumption and quality of rice during paddy drying with industrial inclined bed dryer (IBD) with average holding capacity of 15 ton in the selected complexes of Padiberas Nasional Berhad (BERNAS)-the national paddy custodian of Malaysia. In reducing paddy moisture content (mc) from 22% to 23% wet basis (wb) down to around 12.5% wb, the final mc, the specific electrical (in terms of primary energy) and the specific thermal energy consumption were found to be varied between 1.44 to 1.95 MJ/kg water evaporated and 2.77 to 3.47 MJ/kg water evaporated, respectively. Analysis revealed that the specific electrical energy consumption was around 20% lesser and the specific thermal energy consumption of IBDs was around 10% higher during drying with air temperature of 41–42 °C than drying with 38–39 °C in reducing paddy mc from 22% to 23% (wb) down to around 12.5% (wb). However, paddy being with almost same initial mc dried using drying temperature of 38–39 °C, IBDs yielded 1–4% higher head rice yield while milling recovery and whiteness were comparable at acceptable milling degree and transparency. The bed air flows between 0.27 and 0.29 m 3 m −2 s −1 resulted in higher head rice yield slightly while its

Elastic Elements in a Wrist Prosthesis for Drumming Reduce Muscular Effort, but Increase Imprecision and Perceived Stress

Directory of Open Access Journals (Sweden)

Georg Stillfried

2018-03-01

Full Text Available Recently, progress has been made in the development of mechanical joints with variable intrinsic stiffness, opening up the search for application areas of such variable-stiffness joints. By varying the stiffness of its joints, the resonant frequency of a system can be tuned to perform cyclical tasks most energy-efficiently, making the variable-stiffness joint a candidate element for an advanced prosthetic device specifically designed for the cyclical task of drumming. A prerequisite for a successful variable-stiffness drumming prosthesis is the ability of human drummers to profitably employ different stiffness levels for playing different beats. In this pilot study, 29 able-bodied subjects (20 drumming novices and 9 experts wear a cuff on the forearm, to which a drumstick is connected using changeable adapters, consisting of several leaf springs with different stiffness and one maximally stiff connection element. The subjects are asked to play simple regular drum beats at different frequencies, one of which is the resonant frequency of the adapter-drumstick system. The subject's performance of each drumming task is rated in terms of accuracy and precision, and the effort is measured using questionnaires for the perceived stress as well as electromyography (EMG for the muscular activity. The experiments show that using springs instead of the stiff connection leads to lower muscular activity, indicating that humans are able to use the energy-storing capabilities of the springs, or that muscular activity is reduced due to the lower mass of the springs. However, the perceived stress is increased and the novices' performance lowered, possibly due to a higher cerebral load for controlling the elastic system. The hypothesis that “matching the resonant frequency of the spring-drumstick system to the desired frequency leads to better performance and lower effort” is not confirmed. Possible explanations are discussed. In conclusion, a series

Elastic Elements in a Wrist Prosthesis for Drumming Reduce Muscular Effort, but Increase Imprecision and Perceived Stress

Science.gov (United States)

Stillfried, Georg; Stepper, Johannes; Neppl, Hannah; Vogel, Jörn; Höppner, Hannes

2018-01-01

Recently, progress has been made in the development of mechanical joints with variable intrinsic stiffness, opening up the search for application areas of such variable-stiffness joints. By varying the stiffness of its joints, the resonant frequency of a system can be tuned to perform cyclical tasks most energy-efficiently, making the variable-stiffness joint a candidate element for an advanced prosthetic device specifically designed for the cyclical task of drumming. A prerequisite for a successful variable-stiffness drumming prosthesis is the ability of human drummers to profitably employ different stiffness levels for playing different beats. In this pilot study, 29 able-bodied subjects (20 drumming novices and 9 experts) wear a cuff on the forearm, to which a drumstick is connected using changeable adapters, consisting of several leaf springs with different stiffness and one maximally stiff connection element. The subjects are asked to play simple regular drum beats at different frequencies, one of which is the resonant frequency of the adapter-drumstick system. The subject's performance of each drumming task is rated in terms of accuracy and precision, and the effort is measured using questionnaires for the perceived stress as well as electromyography (EMG) for the muscular activity. The experiments show that using springs instead of the stiff connection leads to lower muscular activity, indicating that humans are able to use the energy-storing capabilities of the springs, or that muscular activity is reduced due to the lower mass of the springs. However, the perceived stress is increased and the novices' performance lowered, possibly due to a higher cerebral load for controlling the elastic system. The hypothesis that “matching the resonant frequency of the spring-drumstick system to the desired frequency leads to better performance and lower effort” is not confirmed. Possible explanations are discussed. In conclusion, a series-elastic element appears to

Automated box/drum waste assay (252Cf shuffler) through the material access and accountability boundary

International Nuclear Information System (INIS)

Horley, E.C.; Bjork, C.W.; Bourret, S.C.; Polk, P.J.; Schneider, C.J.; Studley, R.V.

1992-01-01

For the first time, a shuffler waste-assay system has been made a part of material access and accountability boundary (MAAB). A 252 Cf Pass-Thru shuffler integrated with a conveyor handling system, will process box or drum waste across the MAAB. This automated system will significantly reduce personnel operating costs because security forces will not be required at the MAAB during waste transfer. Further, the system eliminates the chance of a mix-up between measured and nonmeasured waste. This Pass-Thru shuffler is to be installed in the Westinghouse Savannah River Company 321M facility to screen waste boxes and drums for 235 U. An automated conveyor will load waste containers into the shuffler, and upon verification, will transfer the containers across the MAAB. Verification will consist of a weight measurement followed by active neutron interrogation. Containers that pass low-level waste criteria will be conveyed to an accumulator section outside the MAAB. If a container fails to meet the waste criteria, it will be rejected and sent back to the load station for manual inspection and repackaging

Mathematical modeling of a mixed flow spray dryer

International Nuclear Information System (INIS)

Kasiri, N.; Delkhan, F.

2001-01-01

In this paper a mathematical model has been developed to simulate the behavior of spray dryers with an up-flowing spray. The model is based on mass, energy and momentum balance on a single droplet , and mass and energy balances on the drying gas. The system of nonlinear differential equations thus obtained is solved to predict the changes in temperature, humidity, diameter, velocity components and the density of the droplets as well as the temperature and the humidity changes of the drying gas. The predicted results were then compared with an industrially available set of results. A good degree of proximity between the two is reported

Impact of Different Standard Type A7A Drum Closure-Ring Practices on Gasket Contraction and Bolt Closure Distance– 15621

Energy Technology Data Exchange (ETDEWEB)

Ketusky, Edward [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Blanton, Paul [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Bobbitt, John H. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2015-03-11

The Department of Energy, the Savannah River National Laboratory, several manufacturers of specification drums, and the United States Department of Transportation (DOT) are collaborating in the development of a guidance document for DOE contractors and vendors who wish to qualify containers to DOT 7A Type A requirements. Currently, the effort is focused on DOT 7A Type A 208-liter (55-gallons) drums with a standard 12-gauge bolted closure ring. The U.S. requirements, contained in Title 49, Part 178.350 “Specification 7A; general packaging, Type A specifies a competent authority review of the packaging is not required for the transport of (Class 7) radioactive material containing less than Type A quantities of radioactive material. For Type AF drums, a 4 ft. regulatory free drop must be performed, such that the drum “suffers maximum damage.” Although the actual orientation is not defined by the specification, recent studies suggest that maximum damage would result from a shallow angle top impact, where kinetic energy is transferred to the lid, ultimately causing heavy damage to the lid, or even worse, causing the lid to come off. Since each vendor develops closure recommendations/procedures for the drums they manufacture, key parameters applied to drums during closing vary based on vendor. As part of the initial phase of the collaboration, the impact of the closure variants on the ability of the drum to suffer maximum damage is investigated. Specifically, closure testing is performed varying: 1) the amount of torque applied to the closure ring bolt; and, 2) stress relief protocol, including: a) weight of hammer; and, b) orientation that the hammer hits the closure ring. After closure, the amount of drum lid gasket contraction and the distance that the closure bolt moves through the closure ring is measured.

Construction of a flexible pilot dryer for products such as biofuels and iron ore pellets; Uppbyggnad av flexibel pilottork foer produkter som biobraenslen och jaernmalmspellets

Energy Technology Data Exchange (ETDEWEB)

Karlsson, Erik; Truedsson, Ida; Stenstroem, Stig

2009-02-15

Drying of different products is an operation that requires large amounts of energy in Sweden, a compilation from 2006 indicates a total use of over 32 TWh of thermal energy. A more energy efficient drying process can thus result in significant savings of energy for this process. The interest to use biofuels for heating purposes increases with increasing energy prices and thus also the interest to dewater and dry these products. Often an excess of low-value heat (flue gases, warm water etc.) is available and it would be desirable to use these streams for drying of different products. The goal in this project has been to carry out two subtasks: A Rebuild and modernise the old pilot dryer at the department so that it can be used for studies of drying kinetics for different products in a bed or as separate particles. B Perform a number of drying experiments with two representative bio-fuels which can be used for evaluation of different proposals for drying of these products. The results will mainly be of interest for companies handling biofuels in the forestry sector, for LKAB producing iron ore pellets and for manufacturers of industrial dryers. The constructed pilot dryer can be used for studies of drying kinetics of different types of products such as bark, wood chips, materials in the form of pellets such as iron ore pellets or wood pellets and foods. If the drying cell is designed so that fine particulate materials are not entrained with the gas flow, products such as municipal or industrial sludges can also be handled in the dryer. The results indicate specific energy use figures of between 2500 and 3000 kJ/kg evaporated water, both for different fractions of bark and independently if the origin of the bark was Vaeroe or Iggesund. The drying time to reach a dry matter content of 60 % for a bed with a thickness of 20 cm and an air velocity of 1 m/s is about 5000 seconds at an air temperature of 50 deg C. It increases to 15000 seconds to reach a dry matter content

Multiloop control of a drum boiler

Directory of Open Access Journals (Sweden)

Alena Kozáková

2014-05-01

Full Text Available The Equivalent Subsystems Method (ESM (Kozáková et al., 2011 is methodology of decentralized controller design in the frequency domain which allows designing local controllers using any SISO frequency domain method. The paper deals with the digital ESM version where digital local PID controllers guaranteeing required performance for the full system are designed for individual equivalent subsystems using the practice-oriented Sine-wave method (Bucz et al., 2012. The proposed decentralized controller design procedure was verified on the nonlinear benchmark drum boiler simulation model (Morilla, 2012.

Solar energy in food processing-a critical appraisal.

Science.gov (United States)

Eswara, Amruta R; Ramakrishnarao, M

2013-04-01

Increasing population and high cost of fuels have created opportunities for using alternate energies for post-harvest processing of foods. Solar food processing is an emerging technology that provides good quality foods at low or no additional fuel costs. A number of solar dryers, collectors and concentrators are currently being used for various steps in food processing and value addition. Society for Energy, Environment and Development (SEED) developed Solar Cabinet Dryer with forced circulation which has been used for dehydration and development of value added products from locally grown fruits, vegetables, leafy greens and forest produce. Drying under simulated shade conditions using UV-reducing Blue filter helps retain nutrients better. Its simple design and ease of handling makes SEED Solar Dryer an ideal choice for application of food processing in rural settings, closer to where the harvest is produced, eliminating the need for expensive transportation or storage of fresh produce. It also creates employment opportunities among the rural population, especially women. Other gadgets based on solar collectors and concentrators currently being used at various steps of food processing are reviewed.

Analysis on energy consumption of drying process for dried Chinese noodles

International Nuclear Information System (INIS)

Wang, Zhenhua; Zhang, Yingquan; Zhang, Bo; Yang, Fuguang; Yu, Xiaolei; Zhao, Bo; Wei, Yimin

2017-01-01

Highlights: • Energy analysis of a tunnel dryer for dried Chinese noodles is completed. • Energy saving performance of dryers with different inlet air was compared. • MND was developed and evaluated, and the efficiency and throughput was improved. - Abstract: Drying is an important operation during the production of dried Chinese noodles, and the energy consumption from drying accounts for approximately 60% of the total energy consumption during the manufacturing process. To investigate the energy consumption and throughput of dryers for dried Chinese noodles, experiments were conducted using a new 130-m long tunnel dryer with two lines of noodles (ND) and an old 60-m long tunnel dryer with five lines of noodles (OD). The energy saving effects of a modified new 130-m long tunnel dryer (MND), which was only modified through the inclusion of automatic control for temperature and humidity without any modifications to the oil heater or ND dryer structure, were also compared. The energy saving effect was determined from the enthalpy difference between the inlet and outlet humid air of the ND and MND. Finally, the MND was found to be better than ND in terms of energy efficiency and throughput, and trends for the future of noodle drying were discussed.