Driver behaviour in motorway car-following transitions and driver support systems

NARCIS (Netherlands)

Feenstra, P.; Horst, A.R.A. van der

2006-01-01

Co-operative driving with speed adaptation functionality has great potential to improve traffic-throughput, traffic-safety, and environmental-impact on heavily used traffic-infrastructures. A driving-simulator study was performed to investigate the driver behaviour with respect to such

CAMAC Driver Support for Windows NT trademark and Lunux trademark

International Nuclear Information System (INIS)

Slimmer, D.A.; Streets, J.M.

1999-01-01

CAMAC is a Modular Instrumentation and Digital Interface System defined as a standardized instrumentation system for Computer Automated Measurement and Control. CAMAC hardware and software has been defined by the NIM Committee (National Instrumentation Methods Committee) of the US Department of Energy and the ESONE Committee (European Standards on Nuclear Electronics Committee) of European Laboratories. Fermi National Accelerator Laboratory has for many years produced software packages that follow the ANSI/IEEE standard 758-1979 for a variety of computers, CAMAC controller interfaces, and operating systems. In order to enable the re-use of existing hardware and software, Fermilab now supports standard routine libraries and drivers for Windows NT 4.0 and the Linux operating systems for the Jorway 411s SCSI Bus CAMAC Driver[l] and the Jorway73A SCSI Bus CAMAC Crate Controller. A number of test stands and small experiments both on-site and off-site are using this software for their CAMAC data acquisition needs

Intelligent car guidance system (parking support system); Chiteki sharyo yudo system (chusha shien system)

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-01

This system enables a driver to park the car at a predetermined spot without the driver seeing the outside scene. The system shows on a driver seat display the steps that the driver is to follow and thereby supports the driver when visibility is poor, when the parking space is difficult to approach, when the driver is a novice, or when the driver is aged. The system ensures accurate positioning of the car by showing the steering direction and angle, the car speed, and the force of braking to the driver. For this purpose, the system knows the absolute car position by the use of an RFID (Radio Frequency Identification) tag which is a kind of IC (Integrated Circuit) card and D-GPS (Differential-Global Positioning System), grasps the relative car position by the use of a gyroscope, and collects data from plural sensors, which are complementary to each other, such as a car-speed sensor and a steering sensor. (translated by NEDO)

Development of Data Acquisition Card Driver for ICRH System on EAST

Science.gov (United States)

Liu, Daming; Luo, Jiarong; Zhao, Yanping; Qin, Chengming

2008-04-01

Presented in this paper is the development of the driver for the data acquisition card with a peripheral component interconnection (PCI) local bus on the ion cyclotron range of frequency heating (ICRH) system. The driver is mainly aimed at the embedded VxWorks system (real-time operating system) which is widely used in various fields of real-time systems. An efficient way is employed to develop this driver, which will advance the real-time control of the ICRH system on the experimental advanced superconductor tokamak (EAST). The driver is designed using the TORNADO integrated development environment (IDE), and implemented in C plus language. The details include the hardware configuration, analogue/digital (A/D) and digital/analogue (D/A) conversion, input and output (I/O) operation of the driver to support over five cards. The data acquisition card can be manipulated in a low-level program and meet the requirements of A/D conversion and D/A outputs.

Should drivers be operating within an automation-free bandwidth? Evaluating haptic steering support systems with different levels of authority.

Science.gov (United States)

Petermeijer, Sebastiaan M; Abbink, David A; de Winter, Joost C F

2015-02-01

The aim of this study was to compare continuous versus bandwidth haptic steering guidance in terms of lane-keeping behavior, aftereffects, and satisfaction. An important human factors question is whether operators should be supported continuously or only when tolerance limits are exceeded. We aimed to clarify this issue for haptic steering guidance by investigating costs and benefits of both approaches in a driving simulator. Thirty-two participants drove five trials, each with a different level of haptic support: no guidance (Manual); guidance outside a 0.5-m bandwidth (Band1); a hysteresis version of Band1, which guided back to the lane center once triggered (Band2); continuous guidance (Cont); and Cont with double feedback gain (ContS). Participants performed a reaction time task while driving. Toward the end of each trial, the guidance was unexpectedly disabled to investigate aftereffects. All four guidance systems prevented large lateral errors (>0.7 m). Cont and especially ContS yielded smaller lateral errors and higher time to line crossing than Manual, Band1, and Band2. Cont and ContS yielded short-lasting aftereffects, whereas Band1 and Band2 did not. Cont yielded higher self-reported satisfaction and faster reaction times than Band1. Continuous and bandwidth guidance both prevent large driver errors. Continuous guidance yields improved performance and satisfaction over bandwidth guidance at the cost of aftereffects and variability in driver torque (indicating human-automation conflicts). The presented results are useful for designers of haptic guidance systems and support critical thinking about the costs and benefits of automation support systems.

Teen driver support system (TDSS) field operational test : final report.

Science.gov (United States)

2015-11-01

Although teen drivers make up a small percentage of the U.S. driving population, they are at an especially high risk : of being involved in a crash. Factors that contribute to teen drivers risk include their lack of experience and their : tendency...

TECHNOLOGICAL DEVELOPMENT OF DRIVING SUPPORT SYSTEMS BASED ON HUMAN BEHAVIORAL CHARACTERISTICS

Directory of Open Access Journals (Sweden)

Shunichi DOI

2006-01-01

Full Text Available Driving support and cruise assist systems are of growing importance in achieving both road traffic safety and convenience. Such driver support seeks to achieve, with the highest possible quality, nothing less than “driver-vehicle symbiosis under all conditions.” At the same time, many traffic accidents result from improper driver behavior. The author focuses on driver behavior under various driving conditions, conducting detailed measurement and analysis of visual perception and attention characteristics as well as perceptual characteristics involved in driving. The aim in doing so is to support research on driving support systems and driving workload reduction technologies that function as human-vehicle systems and take such characteristics into account.

Home Discharge and Out-of-Hospital Follow-Up of Total Artificial Heart Patients Supported by a Portable Driver System

Science.gov (United States)

2014-01-01

To enhance ambulation and facilitate hospital discharge of total artificial heart (TAH)–supported patients, we adapted a mobile ventricular assistance device (VAD) driver (Excor) for TAH use and report on the performance of Excor-driven TAH patients discharged home. Ten patients stabilized on a TAH, driven by the CSS (“Circulatory Support System”), were progressively switched over to the Excor in hospital over 14 days as a pilot, with daily hemodynamics and laboratory parameters measured. Twenty-two stable TAH patients were subsequently placed on the Excor, trained, and discharged home. Clinical and hemodynamic parameters were followed. All pilot study patients were clinically stable on the Excor, with no decrease in TAH output noted (6.3 + 0.3 L/min [day 1] vs. 5.8 + 0.2 L/min [day 14], p = 0.174), with a trend suggesting improvement of both hepatic and renal function. Twenty-two TAH patients were subsequently successfully discharged home on the portable driver and were supported out of hospital for up to 598 days (range, 2–598; mean = 179 ± 140 days), remaining ambulatory, New York Heart Association (NYHA) class I or II, and free of readmission for 88.5% of the time of support. TAH patients may be effectively and safely supported by a mobile drive system. As such, the utility of the TAH may be extended to support patients beyond the hospital, at home, with overall ambulatory freedom. PMID:24577369

BASIC STUDY ON TAILORMADE BRAKING SUPPORT SYSTEM

Directory of Open Access Journals (Sweden)

Toshiya HIROSE, M.S.

2004-01-01

This research reviewed the construction of models of a Tailormade Braking Support System (TBSS for braking to stop vehicles and the evaluation of drivers. As a result, the following conclusions were drawn. (1 Braking factors were found to change in the period from the start of braking to stopping; (2 Changes in braking factors can be logically incorporated into the control elements of braking support system; (3 Readymade Driver Model is effective as a model to be incorporated into the base system of TBSS; (4 Tailormade Driver Model built on Neural Network is effective as a main model to construct TBSS; (5 As for TBSS, both subjective and objective ratings on the timing and magnitude of braking are favorable, and its safety and sense of security are improved.

Drivers\\' Life Quality, Marital Satisfaction, and Social Support in Cargo Terminal of Yazd City

Directory of Open Access Journals (Sweden)

Mohammad Ali Morovati Sharifabadi

2017-02-01

Full Text Available Abstract Introduction: This is important to consider the health, social support, and marital satisfaction of drivers since they own one of the essential and stressful jobs in society. The purpose of this research was to investigate quality of life, marital satisfaction, and social support of the drivers referring to the cargo terminal of Yazd City. Methods: In order to collect data, 134 drivers in Yazd cargo terminal were selected. The ENRICH questionnaire of marital satisfaction, SF-36 questionnaire, and social support questionnaire (SSQ have been used as data collection tools. The collected data were then analyzed by Independent T test, Analysis of Variance (ANOVA, and Pearson correlation. Results: According to the results, the drivers' average age was 40.2±9.17 years old. The mean scores of marital satisfaction, quality of life, and social support were equal to 120.04±20.14 out of 175, 99.69±18.14 out of 149, and 15±4.76 out of 23, respectively. About 60.4 % of drivers were not satisfied with their jobs. There were significant relationships between weight and marital satisfaction (P=0.02, as well as between job satisfaction (P=0.003 (P=0.015 and income (P=0.047 (P=0.020, to social support and quality of life. Also, a strong significant positive relationship was observed in correlation coefficient between social support and two variables of quality of life and marital satisfaction (P=0.000. Conclusion: This can be argued that marital satisfaction, quality of life, and social support of the drivers are lower than the expected levels. Therefore, it can be concluded that physical and mental health of drivers can be effective on safety of roads; thereby it is necessary to improve their conditions in marital satisfaction, quality of life, and social support

Reducing risky driver behaviour through the implementation of a driver risk management system

Directory of Open Access Journals (Sweden)

Rose Luke

2014-11-01

Full Text Available South Africa has one of the highest incidences of road accidents in the world. Most accidents are avoidable and are caused by driver behaviour and errors. The purpose of this article was to identify the riskiest driver behaviours in commercial fleets in South Africa, to determine the business impact of such behaviour, to establish a framework for the management of risky driver behaviour and to test the framework by applying a leading commercial driver behaviour management system as a case study. The case study comprised three South African commercial fleets. Using data from these fleets, critical incident triangles were used to determine the ratio data of risky driver behaviour to near-collisions and collisions. Based on managing the riskiest driver behaviours as causes of more serious incidents and accidents, the results indicated that through the implementation of an effective driver risk management system, risky incidents were significantly reduced.

[Social support and occupational stress relationship analysis of 1 413 train drivers in a railway bureau].

Science.gov (United States)

Gu, G Z; Yu, S F; Zhou, W H; Wu, H; Kang, L; Chen, R

2017-02-06

Objective: To investigate the social support status of train drivers. Methods: Using cluster sampling, a cross-sectional study was conducted in 1 413 male train drivers (including 301 passenger train drivers, 683 freight train drivers, 85 guest scheduling train drivers, 265 cargo adjustable drivers, and 79 high-speed train drivers) from a railway bureau depot. The survey included individual factors, social support, occupational stressors, strains, personalities, and coping strategy using occupational stress instruments and effort-reward imbalance questionnaire. We compared the difference in social support scores between different drivers, who were divided according to job type and age. Additionally, the correlation between social support score and job strain-related factors was analyzed. The influence of depressive symptoms and job satisfaction were analyzed using a non-conditional logistic multivariate model. Results: The overall average age P (50) ( P (25), P (75)) of 1 413 train drivers was 33.92 (27.83,43.58) years. The overall average length of service 12.25 (5.25,22.75) years. A significant difference in social support scores was observed according to job type ( H =23.23, P40 years (27 (22,31)). Correlation analysis revealed that the social support score was negatively associated with job satisfaction ( r=- 0.43), reward ( r=- 0.22), working stability ( r=- 0.23), promotion opportunities ( r=- 0.12), positive affectivity ( r=- 0.31), esteem ( r=- 0.21), and self-esteem ( r=- 0.20) scores ( Pstress ( r= 0.29), negative affectivity ( r= 0.23), and depressive symptoms ( r= 0.44) scores ( Poccupational stress. High social support was related to reduction in the occurrence of occupational stress, depressive symptoms, and low job satisfaction. Social support is related to mental health of train drivers.

Integrated Context-Aware Driver Assistance System Architecture

Directory of Open Access Journals (Sweden)

Elhadi M. Shakshuki

2013-01-01

Full Text Available Recently, significant improvements have been made in the area of vehicular communication systems. Furthermore, vehicle-to-vehicle communication is considered a key concept for keeping roads safe. An efficient implementation of these systems is necessary to ensure the safety of driving situations and to reduce the collision rates. This paper proposes a Context-Aware Driver Assistance System that links drivers with the physical environment surrounding them using multiple types of sensors and traffic systems as well as considering the senior driver's difficulties and the system processing time. This is achieved by developing a warning system that assists drivers to avoid collisions and improve their response times. The proposed system architecture consists of a set of components to process the user's request such as parking assistance, and to provide responses and advices when needed. These components include communication, knowledge exchange, knowledge update, and context-history. Also, it includes other processes such as context-history manipulation, hazard detection, and hazard detection control. The main goal of the proposed system is to reduce the number of car accidents and improve driver's decisions. The NXT Robotic environment is used to demonstrate the feasibility of the proposed system.

Advanced driver assistance systems for teen drivers: Teen and parent impressions, perceived need, and intervention preferences.

Science.gov (United States)

Weiss, Eve; Fisher Thiel, Megan; Sultana, Nahida; Hannan, Chloe; Seacrist, Thomas

2018-02-28

From the advent of airbags to electronic stability control, technological advances introduced into automobile design have significantly reduced injury and death from motor vehicle crashes. These advances are especially pertinent among teen drivers, a population whose leading cause of death is motor vehicle crashes. Recently developed advanced driver assistance systems (ADAS) have the potential to compensate for skill deficits and reduce overall crash risk. Yet, ADAS is only effective if drivers are willing to use it. Limited research has been conducted on the suitability of ADAS for teen drivers. The goal of this study is to identify teen drivers' perceived need for ADAS, receptiveness to in-vehicle technology, and intervention preferences. The long-term goal is to understand public perceptions and barriers to ADAS use and to help determine how these systems must evolve to meet the needs of the riskiest driving populations. Three focus groups (N = 24) were conducted with licensed teen drivers aged 16-19 years and 2 focus groups with parents of teen drivers (N = 12). Discussion topics included views on how ADAS might influence driving skills and behaviors; trust in technology; and data privacy. Discussions were transcribed; the team used conventional content analysis and open coding methods to identify 12 coding domains and code transcripts with NVivo 10. Interrater reliability testing showed moderate to high kappa scores. Overall, participants recognized potential benefits of ADAS, including improved safety and crash reduction. Teens suggested that ADAS is still developing and therefore has potential to malfunction. Many teens reported a greater trust in their own driving ability over vehicle technology. They expressed that novice drivers should learn to drive on non-ADAS-equipped cars and that ADAS should be considered a supplemental aid. Many teens felt that overreliance on ADAS may increase distracted driving or risky behaviors among teens. Parents also

Over-the-Horizon Awareness for Advanced Driver Assistance Systems: the TrafficFilter and microSlotted 1-Persistence Flooding

NARCIS (Netherlands)

van Eenennaam, Martijn; Heijenk, Geert; Karagiannis, Georgios; van Arem, Bart

2011-01-01

Vehicle-to-vehicle communications (V2V) is a promising technique for Advanced Driver Assistance Systems to increase traffic safety and efficiency. A proposed system is the Congestion Assistant, which supports drivers when approaching and driving in traffic congestion. Studies have shown great

Safety implications of electronic driving support systems : an orientation.

OpenAIRE

Gundy, C.M. Steyvers, F.J.J.M. & Kaptein, N.A.

1995-01-01

This report focuses on traffic safety aspects of driving support systems. The report consists of two parts. First of all, the report discusses a number of topics, relevant for the implementation and evaluation of driving support systems. These topics include: (1) safety research into driving support systems: (2) the importance of research into driver models and the driving task; (3) horizontal integration of driving support systems; (4) vertical integration of driving support systems; (5) tas...

Microcontroller based driver alertness detection systems to detect drowsiness

Science.gov (United States)

Adenin, Hasibah; Zahari, Rahimi; Lim, Tiong Hoo

2018-04-01

The advancement of embedded system for detecting and preventing drowsiness in a vehicle is a major challenge for road traffic accident systems. To prevent drowsiness while driving, it is necessary to have an alert system that can detect a decline in driver concentration and send a signal to the driver. Studies have shown that traffc accidents usually occur when the driver is distracted while driving. In this paper, we have reviewed a number of detection systems to monitor the concentration of a car driver and propose a portable Driver Alertness Detection System (DADS) to determine the level of concentration of the driver based on pixelated coloration detection technique using facial recognition. A portable camera will be placed at the front visor to capture facial expression and the eye activities. We evaluate DADS using 26 participants and have achieved 100% detection rate with good lighting condition and a low detection rate at night.

Modeling of Driver Steering Operations in Lateral Wind Disturbances toward Driver Assistance System

Science.gov (United States)

Kurata, Yoshinori; Wada, Takahiro; Kamiji, Norimasa; Doi, Shun'ichi

Disturbances decrease vehicle stability and increase driver's mental and physical workload. Especially unexpected disturbances such as lateral winds have severe effect on vehicle stability and driver's workload. This study aims at building a driver model of steering operations in lateral wind toward developing effective driver assistance system. First, the relationship between the driver's lateral motion and its reactive quick steering behavior is investigated using driving simulator with lateral 1dof motion. In the experiments, four different wind patterns are displayed by the simulator. As the results, strong correlation was found between the driver's head lateral jerk by the lateral disturbance and the angular acceleration of the steering wheel. Then, we build a mathematical model of driver's steering model from lateral disturbance input to steering torque of the reactive quick feed-forward steering based on the experimental results. Finally, validity of the proposed model is shown by comparing the steering torque of experimental results and that of simulation results.

Study on driving control behavior for lane change maneuver. Analysis of expert driver using neural network system; Shasen henkoji no driver sosa tokusei. Neural network system ni yoru jukuren driver no kaiseki

Energy Technology Data Exchange (ETDEWEB)

Yang, Z; Okayama, T; Katayama, T [Japan Automobile Research Institute Inc., Tsukuba (Japan); Kageyama, I [Nihon University, Tokyo (Japan)

1997-10-01

In order to study driver steering control behavior for vehicle, a driver model for single-lane change maneuver is constructed by a neural network system concerned with the man-machine-environment system. And, using sensitivity analysis, it is found that the model represent the driver control behavior, and the relation between the driver control behavior and vehicle responses. The sensitivity analysis is also examined by applying to the 2nd order predictive driver model. The validity of the sensitivity analysis is confirmed. 5 refs., 8 figs.

Short-term cardiovascular measures for driver support: Increasing sensitivity for detecting changes in mental workload.

Science.gov (United States)

Stuiver, Arjan; Brookhuis, Karel A; de Waard, Dick; Mulder, Ben

2014-02-05

With on-going increases in traffic density and the availability of more and more in-vehicle technology, driver overload is a growing concern. To reduce the burden of workload on the driver, it is essential that support systems that become available are able to use estimations of drivers' workload. In this paper a short-term cardiovascular approach to assess drivers' mental workload is described using data collected in a driving simulator study. The effects of short lasting increases in task demand (40s) on heart rate and blood pressure and derived variability measures are applied as indicators of mental effort. Fifteen drivers participated in 6 sessions of 1.5h in a driving simulator study. Two traffic density levels (7.5minute segments) were compared in which short-segments (40s) of fog were used to induce additional workload demands. Higher traffic density was reflected in increased systolic blood pressure and decreased blood pressure variability. Heart rate variability and blood pressure variability measures decreased during driving in fog in the low traffic condition, indicating increased effort investment during fog in this condition. The results show that the described short-term measures can be applied to give an indication of cardiovascular reactivity as a function workload. Copyright © 2014 Elsevier B.V. All rights reserved.

SCALE system driver

International Nuclear Information System (INIS)

Petrie, L.M.

1984-01-01

The SCALE driver was designed to allow implementation of a modular code system consisting of control modules, which determine the calculation path, and functional modules, which perform the basic calculations. The user can either select a control module and have that module determine the execution path, or the user can select functional modules directly by input

A COOPERATIVE ASSISTANCE SYSTEM BETWEEN VEHICLES FOR ELDERLY DRIVERS

Directory of Open Access Journals (Sweden)

Naohisa HASHIMOTO

2009-01-01

Full Text Available This paper proposes a new concept of elderly driver assistance systems, which performs the assistance by cooperative driving between two vehicles, and describes some experiments with elderly drivers. The assistance consists of one vehicle driven by an elderly driver called a guest vehicle and the other driven by a assisting driver called a host vehicle, and the host vehicle assists or escorts the guest vehicle through the inter-vehicle communications. The functions of the systems installed on a single-seat electric vehicle are highly evaluated by subjects of elderly drivers in virtual streets on a test track.

Implementation Of CAN Based Intelligent Driver Alert System

Directory of Open Access Journals (Sweden)

Yin Mar Win Kyaw Myo Maung Maung

2015-08-01

Full Text Available This system is an attempt to analyze Intelligent Driver Alert System Using CAN Protocol. CAN Controller Area Network offer an efficient communication protocol among sensors actuators controllers and other nodes in real-time applications and is known for its simplicity reliability and high performance. It has given an effective way by which can increase the car and driver safety. This system presents the development and implementation of a digital driving system for a semi-autonomous vehicle to improve the driver-vehicle interface using microcontroller based data acquisition system that uses ADC to bring all control data from analog to digital format. In this system the signal information like temperature LM35 sensor if the temperature increase above the 60 o C and ultrasonic sensor is adapted to measure the distance between the object and vehicle if obstacle is detected within 75cm from the vehicle the controller gives buzzer to the driver speed measure using RPM sensor if revolution increase up to 1200 per minute controller act and to avoid the maximum revolution and to check the fuel level continuously and display in the percentage if fuel level below 20 percent the controller also gives buzzer to the driver and distance fuel level and temperature continuously display on the LCD.

Cedar Avenue driver assist system evaluation report.

Science.gov (United States)

2011-12-01

This paper summarizes an evaluation of the Driver Assist System (DAS) used by the Minnesota Valley Transit Authority (MTVA) for bus shoulder operations. The DAS is a GPS-based technology suite that provides lane-position feedback to the driver via a ...

THE RELATION BETWEEN DRIVER BEHAVIOR AND INTELLIGENT TRANSPORT SYSTEM

Directory of Open Access Journals (Sweden)

Alica Kalašová

2017-12-01

Full Text Available The main objective of Slovakia’s transport policy is to reduce the number of traffic accidents and increase safety on our roads. Implementation of intelligent transport systems presents one of the possibilities how to meet this goal. Acceptance of these systems by motor vehicle drivers and other road traffic participants is necessary in order for them to fulfill their purpose. Only if the drivers will accept intelligent transport systems, it is possible to flexibly and effectively manage road traffic flexibly and effectively. From the perspective of a driver it concerns, in particular, the possibility of using alternative routes when traffic accidents or other obstacles occurs on the route that would significantly affect the continuity and safety of road traffic. Thanks to these technologies, it is possible to choose the appropriate route while driving, of course based on the criterion, which the driver considers the most important during the transport from origin to destination (driving time, distance from origin to destination, fuel consumption, quality of infrastructure. Information isare provided to the driver through variable message signs or directly in the vehicle (RDS-TMC. Another advantage of intelligent transport systems is a positive impact on psychological well-being of the driver while driving. Additional information about the possible obstacles, weather conditions and dangerous situations that occur on the roads as well as alternative routes are provided to the driver well in advance. This paper is mainly focused on how the drivers perceive the influence of intelligent transport systems in Žilina region.

Cooperative advanced Driver assistance Systems - Technological measures for data privacy compliance

OpenAIRE

Jäger, Hubert; Schnieder, Lars

2016-01-01

Cooperative advanced driver assistance systems (ADAS) will contribute to road traffic safety: Critical situations will be detected, the driver alerted and control of the vehicle interfered with automatically. However, the introduction of such driver assistance systems presupposes that data privacy issues have already been solved in advance. A necessary condition for the driver to accept and trust new Driver assistance systems is that his/her personal and personally identifiable data will be t...

Driver-centred vehicle automation: using network analysis for agent-based modelling of the driver in highly automated driving systems.

Science.gov (United States)

Banks, Victoria A; Stanton, Neville A

2016-11-01

To the average driver, the concept of automation in driving infers that they can become completely 'hands and feet free'. This is a common misconception, however, one that has been shown through the application of Network Analysis to new Cruise Assist technologies that may feature on our roads by 2020. Through the adoption of a Systems Theoretic approach, this paper introduces the concept of driver-initiated automation which reflects the role of the driver in highly automated driving systems. Using a combination of traditional task analysis and the application of quantitative network metrics, this agent-based modelling paper shows how the role of the driver remains an integral part of the driving system implicating the need for designers to ensure they are provided with the tools necessary to remain actively in-the-loop despite giving increasing opportunities to delegate their control to the automated subsystems. Practitioner Summary: This paper describes and analyses a driver-initiated command and control system of automation using representations afforded by task and social networks to understand how drivers remain actively involved in the task. A network analysis of different driver commands suggests that such a strategy does maintain the driver in the control loop.

Driving with a partially autonomous forward collision warning system: how do drivers react?

Science.gov (United States)

Muhrer, Elke; Reinprecht, Klaus; Vollrath, Mark

2012-10-01

The effects of a forward collision warning (FCW) and braking system (FCW+) were examined in a driving simulator study analyzing driving and gaze behavior and the engagement in a secondary task. In-depth accident analyses indicate that a lack of appropriate expectations for possible critical situations and visual distraction may be the major causes of rear-end crashes. Studies with FCW systems have shown that a warning alone was not enough for a driver to be able to avoid the accident. Thus,an additional braking intervention by such systems could be necessary. In a driving simulator experiment, 30 drivers took part in a car-following scenario in an urban area. It was assumed that different lead car behaviors and environmental aspects would lead to different drivers' expectations of the future traffic situation. Driving with and without FCW+ was introduced as a between-subjects factor. Driving with FCW+ resulted in significantly fewer accidents in critical situations. This result was achieved by the system's earlier reaction time as compared with that of drivers. The analysis of the gaze behavior showed that driving with the system did not lead to a stronger involvement in secondary tasks. The study supports the hypotheses about the importance of missing expectations for the occurrence of accidents. These accidents can be prevented by an FCW+ that brakes autonomously. The results indicate that an autonomous braking intervention should be implemented in FCW systems to increase the effectiveness of these assistance systems.

Fusion of optimized indicators from Advanced Driver Assistance Systems (ADAS) for driver drowsiness detection.

Science.gov (United States)

Daza, Iván García; Bergasa, Luis Miguel; Bronte, Sebastián; Yebes, Jose Javier; Almazán, Javier; Arroyo, Roberto

2014-01-09

This paper presents a non-intrusive approach for monitoring driver drowsiness using the fusion of several optimized indicators based on driver physical and driving performance measures, obtained from ADAS (Advanced Driver Assistant Systems) in simulated conditions. The paper is focused on real-time drowsiness detection technology rather than on long-term sleep/awake regulation prediction technology. We have developed our own vision system in order to obtain robust and optimized driver indicators able to be used in simulators and future real environments. These indicators are principally based on driver physical and driving performance skills. The fusion of several indicators, proposed in the literature, is evaluated using a neural network and a stochastic optimization method to obtain the best combination. We propose a new method for ground-truth generation based on a supervised Karolinska Sleepiness Scale (KSS). An extensive evaluation of indicators, derived from trials over a third generation simulator with several test subjects during different driving sessions, was performed. The main conclusions about the performance of single indicators and the best combinations of them are included, as well as the future works derived from this study.

Fusion of Optimized Indicators from Advanced Driver Assistance Systems (ADAS for Driver Drowsiness Detection

Directory of Open Access Journals (Sweden)

Iván G. Daza

2014-01-01

Full Text Available This paper presents a non-intrusive approach for monitoring driver drowsiness using the fusion of several optimized indicators based on driver physical and driving performance measures, obtained from ADAS (Advanced Driver Assistant Systems in simulated conditions. The paper is focused on real-time drowsiness detection technology rather than on long-term sleep/awake regulation prediction technology. We have developed our own vision system in order to obtain robust and optimized driver indicators able to be used in simulators and future real environments. These indicators are principally based on driver physical and driving performance skills. The fusion of several indicators, proposed in the literature, is evaluated using a neural network and a stochastic optimization method to obtain the best combination. We propose a new method for ground-truth generation based on a supervised Karolinska Sleepiness Scale (KSS. An extensive evaluation of indicators, derived from trials over a third generation simulator with several test subjects during different driving sessions, was performed. The main conclusions about the performance of single indicators and the best combinations of them are included, as well as the future works derived from this study.

The micro-step motor controller protocol and driver

International Nuclear Information System (INIS)

Hong, Kwang Pyo; Lee, Chang Hee; Moon, Myung Kook; Choi, Bung Hun; Choi, Young Hyun; Cheon, Jong Gu

2004-11-01

We developed the communication protocol which is a main kernel of motor control firmware program that is used at HANARO neutron spectrometer now. This protocol driver divide into as a 4 group(Serial protocol, DLL, Active-X, Labview driver), so end-user can control the motor control as easily by PC RS232/422 port and have a merits as follows: Support a Low Level/High level driver, Support a Network Connectivity function by using High level Driver, One Server can services many client request. By using this protocol, The End-user can be easily makes a application motor control program and developed another application system program by using several kinds of programming tools under Widows and Linux based operation systems

Study of human interface for narrow road drive assist system considered characteristic of driver; Driver no tokusei wo koryoshita kyoro soko shien system no human interface no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Ikeda, A [Subaru Research Center Co., Tokyo (Japan); Amada, N; Kawashima, H [Keio University, Tokyo (Japan)

1997-10-01

The measurement of driver`s watching point, driving time on narrow road and the evaluation of stress etc. were conducted in order to construct the narrow road drive assist system using the stereo image recognition system. Consequently, the driver`s thinking process, stress factor and the indispensable information for this system were clarified. 4 refs., 8 figs., 3 tabs.

Drivers of forests and tree-based systems for food security and nutrition

DEFF Research Database (Denmark)

Kleinschmit, Daniela; Sijapati Basnett, Bimbika; Martin, Adrian

2015-01-01

In the context of this chapter, drivers are considered to be natural or anthropogenic developments affecting forests and tree-based systems for food security and nutrition. They can improve and contribute to food security and nutrition, but they can also lead to food insecurity and malnutrition. ...... consumption, income and livelihood; or through both. These drivers are interrelated and can have different consequences depending on the social structure; for example, they can support food security for elite groups but can increase the vulnerability of other groups.......In the context of this chapter, drivers are considered to be natural or anthropogenic developments affecting forests and tree-based systems for food security and nutrition. They can improve and contribute to food security and nutrition, but they can also lead to food insecurity and malnutrition......, commercialisation of agriculture, industrialisation of forest resources, gender imbalances, conflicts, formalisation of tenure rights, rising food prices and increasing per capita income) were identified within these four categories. They affect food security and nutrition through land use and management; through...

Analyzing Drivers' Attitude towards HUD System Using a Stated Preference Survey

Directory of Open Access Journals (Sweden)

Hongwei Guo

2014-02-01

Full Text Available It is very important for drivers to obtain driving information easily and efficiently. There are many advanced devices used for driving safety assistance. Of these assistance devices, the head-up display (HUD system can promote the reduction of driver's reaction time and improve spatial awareness. The drivers' attitude towards and preference for HUD system are crucial to design the functional framework and interface of HUD system. This study explored the relationships between drivers' attitude and HUD presentation image designs using stated preference data from questionnaire survey. The questionnaire included drivers' attitude towards the use of HUD and the preference for the information display zone and information display elements of the HUD. Contrastive analysis was adopted to examine the variations in drivers' attitude and preference for age and driving skills. According to the results, the participants have varying attitudes to HUD system, but most participants show relatively unified preference for the information display zone and information display elements. The results can also be used to customize a HUD presentation image which is in accordance with the drivers' feelings and preferences.

Why drivers use cell phones and support legislation to restrict this practice.

Science.gov (United States)

Sanbonmatsu, David M; Strayer, David L; Behrends, Arwen A; Ward, Nathan; Watson, Jason M

2016-07-01

The use of cell phones while driving is ubiquitous, particularly in countries where the practice is legal. However, surveys indicate that most drivers favor legislation to limit the use of mobile devices during the operation of a vehicle. A study was conducted to understand this inconsistency between what drivers do and what they advocate for others. Participants completed a survey about their driving attitudes, abilities, and behaviors. Following previous research, drivers reported using cell phones for benefits such as getting work done. The hypocrisy of using cell phones while advocating restrictions appears to stem from differences in the perceived safety risks of self vs. others' use of cell phones. Many if not most drivers believe they can drive safely while using mobile devices. However, they lack confidence in others' ability to drive safely while distracted and believe that others' use of cell phones is dangerous. The threat to public safety of others' usage of mobile devices was one of the strongest independent predictors of support for legislation to restrict cell phone use. Published by Elsevier Ltd.

Car drivers' perceptions of electronic stability control (ESC) systems.

Science.gov (United States)

Vadeby, Anna; Wiklund, Mats; Forward, Sonja

2011-05-01

As a way to reduce the number of car crashes different in-car safety devices are being introduced. In this paper one such application is being investigated, namely the electronic stability control system (ESC). The study used a survey method, including 2000 private car drivers (1000 driving a car with ESC and 1000 driving a car without ESC). The main objective was to investigate the effect of ESC on driver behaviour. Results show that drivers report that they drive even more carelessly when they believe that they have ESC, than when they do not. Men are more risk prone than women and young drivers more than older drivers. Using the theory of planned behaviour the results show that attitude, subjective norm and perceived control explain between 62% and 67% of driver's variation of intentions to take risks. When descriptive norm was added to the model a small but statistically significant increase was found. The study also shows that more than 35% erroneously believe that their car is equipped with an ESC system. These findings may suggest that driver behaviour could reduce the positive effect ESC has on accidents. It also shows that drivers who purchase a new car are not well informed about what kind of safety devices the car is equipped with. These findings highlight the need for more targeted information to drivers. Copyright © 2010 Elsevier Ltd. All rights reserved.

Wireless and wearable EEG system for evaluating driver vigilance.

Science.gov (United States)

Lin, Chin-Teng; Chuang, Chun-Hsiang; Huang, Chih-Sheng; Tsai, Shu-Fang; Lu, Shao-Wei; Chen, Yen-Hsuan; Ko, Li-Wei

2014-04-01

Brain activity associated with attention sustained on the task of safe driving has received considerable attention recently in many neurophysiological studies. Those investigations have also accurately estimated shifts in drivers' levels of arousal, fatigue, and vigilance, as evidenced by variations in their task performance, by evaluating electroencephalographic (EEG) changes. However, monitoring the neurophysiological activities of automobile drivers poses a major measurement challenge when using a laboratory-oriented biosensor technology. This work presents a novel dry EEG sensor based mobile wireless EEG system (referred to herein as Mindo) to monitor in real time a driver's vigilance status in order to link the fluctuation of driving performance with changes in brain activities. The proposed Mindo system incorporates the use of a wireless and wearable EEG device to record EEG signals from hairy regions of the driver conveniently. Additionally, the proposed system can process EEG recordings and translate them into the vigilance level. The study compares the system performance between different regression models. Moreover, the proposed system is implemented using JAVA programming language as a mobile application for online analysis. A case study involving 15 study participants assigned a 90 min sustained-attention driving task in an immersive virtual driving environment demonstrates the reliability of the proposed system. Consistent with previous studies, power spectral analysis results confirm that the EEG activities correlate well with the variations in vigilance. Furthermore, the proposed system demonstrated the feasibility of predicting the driver's vigilance in real time.

Design and validation of advanced driver assistance systems

NARCIS (Netherlands)

Gietelink, O.J.

2007-01-01

This thesis presents new tools and methods for the design and validation of advanced driver assistance systems (ADASs). ADASs aim to improve driving comfort and traffic safety by assisting the driver in recognizing and reacting to potentially dangerous traffic situations. A major challenge in

Factors correlated with traffic accidents as a basis for evaluating Advanced Driver Assistance Systems.

Science.gov (United States)

Staubach, Maria

2009-09-01

This study aims to identify factors which influence and cause errors in traffic accidents and to use these as a basis for information to guide the application and design of driver assistance systems. A total of 474 accidents were examined in depth for this study by means of a psychological survey, data from accident reports, and technical reconstruction information. An error analysis was subsequently carried out, taking into account the driver, environment, and vehicle sub-systems. Results showed that all accidents were influenced by errors as a consequence of distraction and reduced activity. For crossroad accidents, there were further errors resulting from sight obstruction, masked stimuli, focus errors, and law infringements. Lane departure crashes were additionally caused by errors as a result of masked stimuli, law infringements, expectation errors as well as objective and action slips, while same direction accidents occurred additionally because of focus errors, expectation errors, and objective and action slips. Most accidents were influenced by multiple factors. There is a safety potential for Advanced Driver Assistance Systems (ADAS), which support the driver in information assimilation and help to avoid distraction and reduced activity. The design of the ADAS is dependent on the specific influencing factors of the accident type.

Driving with intelligent vehicles: driving behaviour with Adaptive Cruise Control and the acceptance by individual drivers

NARCIS (Netherlands)

Hoedemaeker, D.M.

1999-01-01

This thesis focuses on the following research questions: What are the effects of driver support systems on driving behaviour? To what extent will driver support systems be accepted by individual drivers? To what extent will driving behaviour and acceptance be determined by individual differences?

Investigation of user needs for driver assistance: results of an Internet questionnaire

NARCIS (Netherlands)

van Driel, Cornelie; van Arem, Bart

2005-01-01

Advanced Driver Assistance Systems (ADAS) aim at supporting the driver with the driving task and are expected to lead to a safer, cleaner and more efficient and comfortable transport system. This paper presents the results of an Internet questionnaire among more than 1000 Dutch car drivers.

The driver, the road, the rules … and the rest? A systems-based approach to young driver road safety.

Science.gov (United States)

Scott-Parker, B; Goode, N; Salmon, P

2015-01-01

The persistent overrepresentation of young drivers in road crashes is universally recognised. A multitude of factors influencing their behaviour and safety have been identified through methods including crash analyses, simulated and naturalistic driving studies, and self-report measures. Across the globe numerous, diverse, countermeasures have been implemented; the design of the vast majority of these has been informed by a driver-centric approach. An alternative approach gaining popularity in transport safety is the systems approach which considers not only the characteristics of the individual, but also the decisions and actions of other actors within the road transport system, along with the interactions amongst them. This paper argues that for substantial improvements to be made in young driver road safety, what has been learnt from driver-centric research needs to be integrated into a systems approach, thus providing a holistic appraisal of the young driver road safety problem. Only then will more effective opportunities and avenues for intervention be realised. Copyright © 2014 Elsevier Ltd. All rights reserved.

Design of a Fatigue Detection System for High-Speed Trains Based on Driver Vigilance Using a Wireless Wearable EEG

Directory of Open Access Journals (Sweden)

Xiaoliang Zhang

2017-03-01

Full Text Available The vigilance of the driver is important for railway safety, despite not being included in the safety management system (SMS for high-speed train safety. In this paper, a novel fatigue detection system for high-speed train safety based on monitoring train driver vigilance using a wireless wearable electroencephalograph (EEG is presented. This system is designed to detect whether the driver is drowsiness. The proposed system consists of three main parts: (1 a wireless wearable EEG collection; (2 train driver vigilance detection; and (3 early warning device for train driver. In the first part, an 8-channel wireless wearable brain-computer interface (BCI device acquires the locomotive driver’s brain EEG signal comfortably under high-speed train-driving conditions. The recorded data are transmitted to a personal computer (PC via Bluetooth. In the second step, a support vector machine (SVM classification algorithm is implemented to determine the vigilance level using the Fast Fourier transform (FFT to extract the EEG power spectrum density (PSD. In addition, an early warning device begins to work if fatigue is detected. The simulation and test results demonstrate the feasibility of the proposed fatigue detection system for high-speed train safety.

Automation warning system against driver falling asleep in-traffic

Directory of Open Access Journals (Sweden)

Dymov I. S.

2017-12-01

Full Text Available The paper is devoted to the development of a new automation recognition and warning system against driver falling asleep in-traffic. The issue of the physical condition control of professional drivers on the voyage has been considered both on the part of efficiency and quality of its determination, and in terms of improving overall road safety. The existing and widely used devices for determining the transition to the stage of sleep of drivers being in-traffic have been analyzed. Their advantages and disadvantages have been detected. It has been established that the main negative factor preventing the mass introduction of pre-existing warning systems is the need to wear one or another monitoring device before starting the movement. Carried out project research work has proposed a complex monitoring of the physical and physiological condition of driving person as a new warning method against falling asleep in-traffic. The proposed variations of algorithmic implementations can be used in long-distance trucks and passenger vehicles. Two different versions of the automatic control status of the driver physical condition have been considered. The first approach has proposed the use of sensors of the biometric parameters of body, pulsus, body temperature, and hands on wheel pressure sensors. The second one has proposed using the tracking cameras. Both for the first and second versions of the automation system a toolset of control devices is being installed inside the vehicle and have no physical, so irritating action on the driver. Software approach for the false operation rejection of the devices has been developed. The paper considers the flow diagrams of the automatic systems and logical structure of analysis and decision-making. The set of impacts intended for driver's awakening has been proposed. The conclusion about the engineering perspectives of the proposed approach of projected automation systems has been made.

The Supporting a Teen's Effective Entry to the Roadway (STEER) Program: Feasibility and Preliminary Support for a Psychosocial Intervention for Teenage Drivers with ADHD

Science.gov (United States)

Fabiano, Gregory A.; Hulme, Kevin; Linke, Stuart; Nelson-Tuttle, Chris; Pariseau, Meaghan; Gangloff, Brian; Lewis, Kemper; Pelham, William E.; Waschbusch, Daniel A.; Waxmonsky, James G.; Gormley, Matthew; Gera, Shradha; Buck, Melina

2011-01-01

Teenage drivers with attention-deficit/hyperactivity disorder (ADHD) are at considerable risk for negative driving outcomes, including traffic citations, accidents, and injuries. Presently, no efficacious psychosocial interventions exist for teenage drivers with ADHD. The Supporting a Teen's Effective Entry to the Roadway (STEER) program is a…

Video-based lane estimation and tracking for driver assistance: Survey, system, and evaluation

OpenAIRE

McCall, J C; Trivedi, Mohan Manubhai

2006-01-01

Driver-assistance systems that monitor driver intent, warn drivers of lane departures, or assist in vehicle guidance are all being actively considered. It is therefore important to take a critical look at key aspects of these systems, one of which is lane-position tracking. It is for these driver-assistance objectives that motivate the development of the novel "video-based lane estimation and tracking" (VioLET) system. The system is designed using steerable filters for robust and accurate lan...

Older drivers and ADAS : which systems improve road safety?

NARCIS (Netherlands)

Davidse, R.J.

2006-01-01

In the coming decades, the number of older drivers that experiences difficulties in traffic as a result of functional limitations will strongly increase. Advanced Driver Assistance Systems (ADAS) could resolve some of these difficulties, by providing personal assistance in a road environment that

Designing Fatigue Warning Systems: The perspective of professional drivers.

Science.gov (United States)

Meng, Fanxing; Li, Shuling; Cao, Lingzhi; Peng, Qijia; Li, Musen; Wang, Chunhui; Zhang, Wei

2016-03-01

Professional drivers have been characterized as experiencing heavy fatigue resulting from long driving time in their daily work. This study aimed to explore the potential demand of Fatigue Warning Systems (FWSs) among professional drivers as a means of reducing the danger of fatigue driving and to examine their opinions regarding the design of FWSs. Six focus groups with 35 participants and a questionnaire survey with 600 respondents were conducted among Chinese truck and taxi drivers to collect qualitative and quantitative data concerning the current situation of fatigue driving and opinions regarding the design of FWSs. The results revealed that both truck and taxi drivers had a positive attitude toward FWSs, and they hoped this system could not only monitor and warn them regarding their fatigue but also somewhat relieve their fatigue before they could stop and rest. As for warning signals, participants preferred auditory warnings, as opposed to visual, vibrotactile or electric stimuli. Interestingly, it was proposed that verbal warnings involving the information regarding consequences of fatigue driving or the wishes of drivers' family members would be more effective. Additionally, different warning patterns, including graded, single and continuous warnings, were discussed in the focus group. Finally, the participants proposed many other suggestions, as well as their concerns regarding FWSs, which will provide valuable information for companies who wish to develop FWSs for professional drivers. Copyright © 2015. Published by Elsevier Ltd.

Intersection assistance: a safe solution for older drivers?

Science.gov (United States)

Dotzauer, Mandy; Caljouw, Simone R; de Waard, Dick; Brouwer, Wiebo H

2013-10-01

Within the next few decades, the number of older drivers operating a vehicle will increase rapidly (Eurostat, 2011). As age increases so does physical vulnerability, age-related impairments, and the risk of being involved in a fatal crashes. Older drivers experience problems in driving situations that require divided attention and decision making under time pressure as reflected by their overrepresentation in at-fault crashes on intersections. Advanced Driver Assistance Systems (ADAS) especially designed to support older drivers crossing intersections might counteract these difficulties. In a longer-term driving simulator study, the effects of an intersection assistant on driving were evaluated. 18 older drivers (M=71.44 years) returned repeatedly completing a ride either with or without a support system in a driving simulator. In order to test the intersection assistance, eight intersections were depicted for further analyses. Results show that ADAS affects driving. Equipped with ADAS, drivers allocated more attention to the road center rather than the left and right, crossed intersections in shorter time, engaged in higher speeds, and crossed more often with a critical time-to-collision (TTC) value. The implications of results are discussed in terms of behavioral adaptation and safety. Copyright © 2013 Elsevier Ltd. All rights reserved.

Assessing the utility of TAM, TPB, and UTAUT for advanced driver assistance systems.

Science.gov (United States)

Rahman, Md Mahmudur; Lesch, Mary F; Horrey, William J; Strawderman, Lesley

2017-11-01

Advanced Driver Assistance Systems (ADAS) are intended to enhance driver performance and improve transportation safety. The potential benefits of these technologies, such as reduction in number of crashes, enhancing driver comfort or convenience, decreasing environmental impact, etc., have been acknowledged by transportation safety researchers and federal transportation agencies. Although these systems afford safety advantages, they may also challenge the traditional role of drivers in operating vehicles. Driver acceptance, therefore, is essential for the implementation of these systems into the transportation system. Recognizing the need for research into the factors affecting driver acceptance, this study assessed the utility of the Technology Acceptance Model (TAM), the Theory of Planned Behavior (TPB), and the Unified Theory of Acceptance and Use of Technology (UTAUT) for modelling driver acceptance in terms of Behavioral Intention to use an ADAS. Each of these models propose a set of factors that influence acceptance of a technology. Data collection was done using two approaches: a driving simulator approach and an online survey approach. In both approaches, participants interacted with either a fatigue monitoring system or an adaptive cruise control system combined with a lane-keeping system. Based on their experience, participants responded to several survey questions to indicate their attitude toward using the ADAS and their perception of its usefulness, usability, etc. A sample of 430 surveys were collected for this study. Results found that all the models (TAM, TPB, and UTAUT) can explain driver acceptance with their proposed sets of factors, each explaining 71% or more of the variability in Behavioral Intention. Among the models, TAM was found to perform the best in modelling driver acceptance followed by TPB. The findings of this study confirm that these models can be applied to ADAS technologies and that they provide a basis for understanding driver

Handbook of driver assistance systems basic information, components and systems for active safety and comfort

CERN Document Server

Hakuli, Stephan; Lotz, Felix; Singer, Christina

2016-01-01

This fundamental work explains in detail systems for active safety and driver assistance, considering both their structure and their function. These include the well-known standard systems such as Anti-lock braking system (ABS), Electronic Stability Control (ESC) or Adaptive Cruise Control (ACC). But it includes also new systems for protecting collisions protection, for changing the lane, or for convenient parking. The book aims at giving a complete picture focusing on the entire system. First, it describes the components which are necessary for assistance systems, such as sensors, actuators, mechatronic subsystems, and control elements. Then, it explains key features for the user-friendly design of human-machine interfaces between driver and assistance system. Finally, important characteristic features of driver assistance systems for particular vehicles are presented: Systems for commercial vehicles and motorcycles.

Heading Control System for a Multi-body Vehicle with a Virtual Test Driver

Directory of Open Access Journals (Sweden)

POSTALCIOGLU OZGEN, S.

2010-08-01

Full Text Available This paper includes a Heading Control (HC system for a multi-body vehicle. HC system helps reducing the required torque from the driver and improves the lane keeping efficiency. HC system is important for safety and driver comfort in traffic. The controller performance is examined on a virtual test drive platform. The optimal control theory is applied to HC system and examined on a curved path and under a side wind disturbance. Different assistance levels are applied to see the characteristics of the controller with different virtual test drivers. The results are analyzed based on three performance indices; lane keeping performance (LKP index, assist torque performance (ATP index and driver torque performance (DTP index. As seen from the results while using HC system the lateral displacement decreases as the lane keeping performance increases and the driver torque performance decreases as the assist torque performance increases.

INFLUENCE OF HMI ERGONOMY ON DRIVERS IN COOPERATIVE SYSTEMS AREA

Directory of Open Access Journals (Sweden)

Tomáš Jizba

2017-12-01

Full Text Available Modern vehicles are getting smarter and utilize more and more the advantages of Advanced Driver Assistance Systems (ADAS. Deployment of upcoming technologies, such as cooperative systems (V2X, will most likely be the key step towards a significant reduction of accidents across the globe. Some of these systems extend driver’s field of vision, so the driver can be forewarned against a wide range of threats. Unlike technology, the human processing capacity has remained almost unchanged over centuries. Therefore, it is necessary to bear in mind that drivers have restricted capabilities to process multiple warnings. In this context, an important question arises: How can be V2X warnings integrated into the Human Machine Interface (HMI of vehicles, and what warning policy is needed to ensure high usability, acceptance, efficiency and understanding of such a warning interface from the driver’s point of view. Using a human centered design approach, two concepts of visual driver-vehicle interface for V2X warnings were developed and evaluated. One of those interfaces was based on a 1-stage warning policy and the second one utilized a dynamic 3-stage warning approach. The research revealed that drivers prefer to have dynamic warnings that correspond with the level of danger to which they are exposed, rather than only one warning displayed in a situation of imminent danger. However, with regards to overall usability score and workload measurements, results showed that the 3-stage system performed worse in comparison with the 1-stage system.

Principle for the Validation of a Driving Support using a Computer Vision-Based Driver Modelization on a Simulator

Directory of Open Access Journals (Sweden)

Baptiste Rouzier

2015-07-01

Full Text Available This paper presents a new structure for a driving support designed to compensate for the problems caused by the behaviour of the driver without causing a feeling of unease. This assistance is based on a shared control between the human and an automatic support that computes and applies an assisting torque on the steering wheel. This torque is computed from a representation of the hazards encountered on the road by virtual potentials. However, the equilibrium between the relative influences of the human and the support on the steering wheel are difficult to find and depend upon the situation. This is why this driving support includes a modelization of the driver based on an analysis of several face features using a computer vision algorithm. The goal is to determine whether the driver is drowsy or whether he is paying attention to some specific points in order to adapt the strength of the support. The accuracy of the measurements made on the face features is estimated, and the interest of the proposal as well as the concepts raised by such assistance are studied through simulations.

"The little squealer" or "the virtual guardian angel"? Young drivers' and their parents' perspective on using a driver monitoring technology and its implications for parent-young driver communication.

Science.gov (United States)

Guttman, Nurit; Gesser-Edelsburg, Anat

2011-02-01

In-vehicle driving monitoring technologies have the potential to enable young drivers to learn from self-assessment. However, their use is largely dependent on parental involvement. A total of 79 interviews were conducted with young drivers and parents regarding this technology and its use. Most had the experience of having an in-vehicle data recorder installed in the vehicle driven by the young drivers. Parents and the young drivers expressed both appreciation as well as reservations about its potential as a means to enhance the driving safety of young drivers. A surprising finding was that some parents did not check the feedback and said they relied on the young driver to do so. Main concerns related to privacy, parent-young driver relationship, self-esteem and confidence, constructive use of the feedback data, and the limitations of the documentation that can be done by the technology. Providing parents and young drivers with a support system and tools to discuss and utilize the feedback are underscored. Challenges include addressing the invasion of young drivers' privacy and gender differences, and using the monitoring-capacity of the technology to enhance safe driving practices. Implications for programs to enhance communication and a dialogical approach between parents and young drivers are discussed. Copyright © 2010 Elsevier Ltd. All rights reserved.

Challenges for Older Drivers in Urban, Suburban, and Rural Settings

Directory of Open Access Journals (Sweden)

Rashmi P. Payyanadan

2018-03-01

Full Text Available Along with age-related factors, geographical settings—urban, suburban, and rural areas—also contribute to the differences in fatal crashes among older drivers. These differences in crash outcomes might be attributed to the various driving challenges faced by older drivers residing in different locations. To understand these challenges from the perspective of the older driver, a focus group study was conducted with drivers 65 and older from urban, suburban, and rural settings. Guided-group interviews were used to assess driving challenges, mobility options, opportunities for driver support systems (DSS, and alternate transportation needs. Content analysis of the interview responses resulted in four categories representing common challenges faced by older drivers across the settings: behavior of other drivers on the road, placement of road signs, reduced visibility of road signs due to age-related decline, and difficulties using in-vehicle technologies. Six categories involved location-specific challenges such as heavy traffic situations for urban and suburban drivers, and multi-destination trips for rural drivers. Countermeasures implemented by older drivers to address these challenges primarily involved route selection and avoidance. Technological advances of DSS systems provide a unique opportunity to support the information needs for route selection and avoidance preferences of drivers. Using the content analysis results, a framework was built to determine additional and modified DSS features to meet the specific challenges of older drivers in urban, suburban, and rural settings. These findings suggest that there is heterogeneity in the driving challenges and preferences of older drivers based on their location. Consequently, DSS technologies and vehicle automation need to be tailored to not only meet the driving safety and mobility needs of older drivers as a population, but also to their driving environment.

SMARTPHONE-BASED APPROACH TO ADVANCED DRIVER ASSISTANCE SYSTEM (ADAS RESEARCH AND DEVELOPMENT

Directory of Open Access Journals (Sweden)

I. B. Lashkov

2015-11-01

Full Text Available Subject of Research.The paper deals with findings and presents asmartphone-based approach to advanced driver assistance system (ADAS research and development.The approach is based on the data of smartphone cameras and sensors. The line of researchis associated with the developmentof mobile advanced driver assistance system (ADAS. Method.The proposedapproach isbased on the use of driver'sand vehicle behavior ontologies. Current ADAS systems can be divided into two main categories according to the method of implementation: mobile applications, manually installed by the driver from the application stores, and safetyhardware and softwaresystems,integrated into vehicles by manufacturesor in the automotive service centers.Mobile application installed on the smartphone uses the built-in rear and front-facing cameras and sensors to monitor both the road and vehicles ahead, and at the same time the driver in order to prevent traffic collisions. The service consists of components for objects recognition in the images obtained with cameras, and components for traffic situation analysis. Main Results. The driver safety mobile application has been developedfor the use on mobile phones.The mobile phone is mounted on the windshield of a car.In case of dangerous event occurrence, the application engine will make an audible or vibration signal to inform the driver to be concentratedand more vigilant. For example, road obstacles, rear-end and stationary vehicle accidents are the most common accident types.The mobile application detects whether a crash is imminent by computing the ‘Time To Contact’ (TTC taking into account host vehicle speed, relative speed and relative acceleration.If the driver doesn’t maintain safe minimum distance with the car immediately ahead, the mobile application will alert the driver by displaying an attention icon with an audible alert. The dual-camera sensing application is designed to help the drivers increase the trip safety

PILOT RESULTS ON FORWARD COLLISION WARNING SYSTEM EFFECTIVENESS IN OLDER DRIVERS.

Science.gov (United States)

Lester, Benjamin D; Sager, Lauren N; Dawson, Jeffrey; Hacker, Sarah D; Aksan, Nazan; Rizzo, Matthew; Kitazaki, Satoshi

2015-06-01

Advanced Driver Assistance Systems (ADAS) have largely been developed with a "one-size-fits-all" approach. This approach neglects the large inter-individual variability in perceptual and cognitive abilities that affect aging ADAS users. We investigated the effectiveness of a forward collision warning (FCW) with fixed response parameters in young and older drivers with differing levels of cognitive functioning. Drivers responded to a pedestrian stepping into the driver's path on a simulated urban road. Behavioral metrics included response times (RT) for pedal controls and two indices of risk penetration (e.g., maximum deceleration and minimum time-to-collision (TTC)). Older drivers showed significantly slower responses at several time points compared to younger drivers. The FCW facilitated response times (RTs) for older and younger drivers. However, older drivers still showed smaller safety gains compared to younger drivers at accelerator pedal release and initial brake application when the FCW was active. No significant differences in risk metrics were observed within the condition studied. The results demonstrate older drivers likely differ from younger drivers using a FCW with a fixed parameter set. Finally, we briefly discuss how future research should examine predictive relationships between domains of cognitive functioning and ADAS responses to develop parameter sets to fit the individual.

Continuous monitoring the vehicle dynamics and driver behavior using navigation systems

Science.gov (United States)

Ene, George

2017-10-01

In all fields cost is very important and the increasing amount of data that are needed for active safety systems, like ADAS, lead to implementation of some complex and powerful unit for processing raw data. In this manner is necessary a cost-effective method to estimate the maximum available tire road friction during acceleration and braking by continuous monitoring the vehicle dynamics and driver behavior. The method is based on the hypothesis that short acceleration and braking periods can indicate vehicle dynamics, and thus the available tire road friction coefficient, and also human behavior and his limits. Support for this hypothesis is found in the literature and is supported by the result of experiments conducted under different conditions and seasons.

Analysis of an induction linac driver system for inertial fusion

International Nuclear Information System (INIS)

Hovingh, J.; Brady, V.O.; Faltens, A.; Keefe, D.; Lee, E.P.

1987-07-01

A linear induction accelerator that produces a beam of energetic (5 to 20 GeV) heavy (130 to 210 amu) ions is a prime candidate as a driver for inertial fusion. Continuing developments in sources for ions with charge state greater than unity allow a potentially large reduction in the driver cost and an increase in the driver efficiency. The use of high undepressed tunes (σ 0 ≅ 85 0 ) and low depressed tunes (σ ≅ 8.5 0 ) also contributes to a potentially large reduction in the driver cost. The efficiency and cost of the induction linac system are discussed as a function of output energy and pulse repetition frequency for several ion masses and charge states. The cost optimization code LIACEP, including accelerating module alternatives, transport modules, and scaling laws, is presented. Items with large cost-leverage are identified as a guide to future research activities and development of technology that can yield substantial reductions in the accelerator system cost and improvement in the accelerator system efficiency. Finally, a cost-effective strategy using heavy ion induction linacs in a development scenario for inertial fusion is presented. 34 refs., 6 figs., 7 tabs

A Context-Aware EEG Headset System for Early Detection of Driver Drowsiness

Directory of Open Access Journals (Sweden)

Gang Li

2015-08-01

Full Text Available Driver drowsiness is a major cause of mortality in traffic accidents worldwide. Electroencephalographic (EEG signal, which reflects the brain activities, is more directly related to drowsiness. Thus, many Brain-Machine-Interface (BMI systems have been proposed to detect driver drowsiness. However, detecting driver drowsiness at its early stage poses a major practical hurdle when using existing BMI systems. This study proposes a context-aware BMI system aimed to detect driver drowsiness at its early stage by enriching the EEG data with the intensity of head-movements. The proposed system is carefully designed for low-power consumption with on-chip feature extraction and low energy Bluetooth connection. Also, the proposed system is implemented using JAVA programming language as a mobile application for on-line analysis. In total, 266 datasets obtained from six subjects who participated in a one-hour monotonous driving simulation experiment were used to evaluate this system. According to a video-based reference, the proposed system obtained an overall detection accuracy of 82.71% for classifying alert and slightly drowsy events by using EEG data alone and 96.24% by using the hybrid data of head-movement and EEG. These results indicate that the combination of EEG data and head-movement contextual information constitutes a robust solution for the early detection of driver drowsiness.

Method and system for communicating with a laser power driver

Science.gov (United States)

Telford, Steven

2017-07-18

A system for controlling a plurality of laser diodes includes an optical transmitter coupled to the laser diode driver for each laser diode. An optical signal including bi-phase encoded data is provided to each laser diode driver. The optical signal includes current level and pulse duration information at which each of the diodes is to be driven. Upon receiving a trigger signal, the laser diode drivers operate the laser diodes using the current level and pulse duration information to output a laser beam.

Untangling the drivers of nonlinear systems with information theory

Science.gov (United States)

Wing, S.; Johnson, J.

2017-12-01

Many systems found in nature are nonlinear. The drivers of the system are often nonlinearly correlated with one another, which makes it a challenge to understand the effects of an individual driver. For example, solar wind velocity (Vsw) and density (nsw) are both found to correlate well with radiation belt fluxes and are thought to be drivers of the magnetospheric dynamics; however, the Vsw is anti-correlated with nsw, which can potentially confuse interpretation of these relationships as causal or coincidental. Information theory can untangle the drivers of these systems, describe the underlying dynamics, and offer constraints to modelers and theorists, leading to better understanding of the systems. Two examples are presented. In the first example, the solar wind drivers of geosynchronous electrons with energy range of 1.8-3.5 MeV are investigated using mutual information (MI), conditional mutual information (CMI), and transfer entropy (TE). The information transfer from Vsw to geosynchronous MeV electron flux (Je) peaks with a lag time (t) of 2 days. As previously reported, Je is anticorrelated with nsw with a lag of 1 day. However, this lag time and anticorrelation can be attributed mainly to the Je(t + 2 days) correlation with Vsw(t) and nsw(t + 1 day) anticorrelation with Vsw(t). Analyses of solar wind driving of the magnetosphere need to consider the large lag times, up to 3 days, in the (Vsw, nsw) anticorrelation. Using CMI to remove the effects of Vsw, the response of Je to nsw is 30% smaller and has a lag time < 24 hr, suggesting that the loss mechanism due to nsw or solar wind dynamic pressure has to start operating in < 24 hr. nsw transfers about 36% as much information as Vsw (the primary driver) to Je. Nonstationarity in the system dynamics are investigated using windowed TE. When the data is ordered according to high or low transfer entropy it is possible to understand details of the triangle distribution that has been identified between Je(t + 2

Driver Psychology during Automated Platooning

NARCIS (Netherlands)

Heikoop, D.D.

2017-01-01

With the rapid increase in vehicle automation technology, the call for understanding how humans behave while driving in an automated vehicle becomes more urgent. Vehicles that have automated systems such as Lane Keeping Assist (LKA) or Adaptive Cruise Control (ACC) not only support drivers in their

A method to investigate drivers' acceptance of Blind Spot Detection System®.

Science.gov (United States)

Piccinini, Giuliofrancesco; Simões, Anabela; Rodrigues, Carlos Manuel; Leitão, Miguel

2012-01-01

Lately, with the goal of improving road safety, car makers developed and commercialised some Advanced Driver Assistance Systems (ADAS) which, through the detection of blind spot areas on the vehicle's sides, could help the drivers during the overtaking and the change lane task. Despite the possible benefits to reduce lateral crashes, the overall impact on road safety of such systems have not been deeply studied yet; notably, despite some researches have been carried out, there is a lack of studies regarding the long-term usage and drivers' acceptance of those systems. In order to fill the research gap, a methodology, based on the combination of focus groups interviews, questionnaires and a small-scale field operational test (FOT), has been designed in this study; such a methodology aims at evaluating drivers' acceptance of Blind Spot Information System® and at proposing some ideas to improve the usability and user-friendliness of this (or similar) device in their future development.

Stress-oriented driver assistance system for electric vehicles.

Science.gov (United States)

Athanasiou, Georgia; Tsotoulidis, Savvas; Mitronikas, Epaminondas; Lymberopoulos, Dimitrios

2014-01-01

Stress is physiological and physical reaction that appears in highly demanding situations and affects human's perception and reaction capability. Occurrence of stress events within highly dynamic road environment could lead to life-threatening situation. With the perspective of safety and comfort driving provision to anxious drivers, in this paper a stress-oriented Driver Assistance System (DAS) is proposed. The DAS deployed on Electric Vehicle. This novel DAS customizes driving command signal in respect to road context, when stress is detected. The effectiveness of this novel DAS is verified by simulation in MATLAB/SIMULINK environment.

On-Road Driver Monitoring System Based on a Solar-Powered In-Vehicle Embedded Platform

OpenAIRE

Yen-Lin Chen; Chao-Wei Yu; Zi-Jie Chien; Chin-Hsuan Liu; Hsin-Han Chiang

2014-01-01

This study presents an on-road driver monitoring system, which is implemented on a stand-alone in-vehicle embedded system and driven by effective solar cells. The driver monitoring function is performed by an efficient eye detection technique. Through the driver’s eye movements captured from the camera, the attention states of the driver can be determined and any fatigue states can be avoided. This driver monitoring technique is implemented on a low-power embedded in-vehicle platform. Besides...

Driver Behavioral Changes through Interactions with an Automatic Brake System for Collision Avoidance

Science.gov (United States)

Itoh, Makoto; Fujiwara, Yusuke; Inagaki, Toshiyuki

This paper discusses driver's behavioral changes as a result of driver's use of an automatic brake system for preventing a rear-end collision from occurring. Three types of automatic brake systems are investigated in this study. Type 1 brake system applies a strong automatic brake when a collision is very imminent. Type 2 brake system initiates brake operation softly when a rear-end crash may be anticipated. Types 1 and 2 are for avoidance of a collision. Type 3 brake system, on the other hand, applies a strong automatic brake to reduce the damage when a collision can not be avoided. An experiment was conducted with a driving simulator in order to analyze the driver's possible behavioral changes. The results showed that the time headway (THW) during car following phase was reduced by use of an automatic brake system of any type. The inverse of time to collision (TTC), which is an index of the driver's brake timing, increased by use of Type 1 brake system when the deceleration rate of the lead vehicle was relatively low. However, the brake timing did not change when the drivers used Type 2 or 3 brake system. As a whole, dangerous behavioral changes, such as overreliance on a brake system, were not observed for either type of brake system.

Getting ADAS on the Road : Actors' Interactions in Advanced Driver Assistance Systems Deployment

NARCIS (Netherlands)

Walta, L.

2011-01-01

Currently, many car drivers spend many hours in congested traffic. If their cars would have been equipped with an electronic system that automatically follows the car in front of them, congestion might have been prevented. Such a system is an example of Advanced Driver Assistance Systems (ADAS).

Brake reactions of distracted drivers to pedestrian Forward Collision Warning systems.

Science.gov (United States)

Lubbe, Nils

2017-06-01

Forward Collision Warning (FCW) can be effective in directing driver attention towards a conflict and thereby aid in preventing or mitigating collisions. FCW systems aiming at pedestrian protection have been introduced onto the market, yet an assessment of their safety benefits depends on the accurate modeling of driver reactions when the system is activated. This study contributes by quantifying brake reaction time and brake behavior (deceleration levels and jerk) to compare the effectiveness of an audio-visual warning only, an added haptic brake pulse warning, and an added Head-Up Display in reducing the frequency of collisions with pedestrians. Further, this study provides a detailed data set suited for the design of assessment methods for car-to-pedestrian FCW systems. Brake response characteristics were measured for heavily distracted drivers who were subjected to a single FCW event in a high-fidelity driving simulator. The drivers maintained a self-regulated speed of 30km/h in an urban area, with gaze direction diverted from the forward roadway by a secondary task. Collision rates and brake reaction times differed significantly across FCW settings. Brake pulse warnings resulted in the lowest number of collisions and the shortest brake reaction times (mean 0.8s, SD 0.29s). Brake jerk and deceleration were independent of warning type. Ninety percent of drivers exceeded a maximum deceleration of 3.6m/s 2 and a jerk of 5.3m/s 3 . Brake pulse warning was the most effective FCW interface for preventing collisions. In addition, this study presents the data required for driver modeling for car-to-pedestrian FCW similar to Euro NCAP's 2015 car-to-car FCW assessment. Practical applications: Vehicle manufacturers should consider the introduction of brake pulse warnings to their FCW systems. Euro NCAP could introduce an assessment that quantifies the safety benefits of pedestrian FCW systems and thereby aid the proliferation of effective systems. Copyright © 2017

Cost/performance analysis of an induction linac driver system for inertial fusion

International Nuclear Information System (INIS)

Hovingh, J.; Brady, V.O.; Faltens, A.; Hoyer, E.H.; Lee, E.P.

1986-01-01

A linear induction accelerator that produces a beam of energetic (≅ 10 GeV) heavy (A ≅ 200) ions is a prime candidate as a driver for inertial fusion. Continuing developments is amorphous iron for use in accelerating modules represent a potentially large reduction in the driver cost and an increase in the driver efficiency. Additional insulator developments may also represent a potentially large reduction in the driver cost. The efficiency and cost of the induction linac system is discussed as a function of output energy and pulse repetition frequency for several beam charge states, numbers of beams and beam particle species. Accelerating modules and transport modules are described. Large cost leverage items are identified as a guide to future research activities and technology of development that can yield further substantial reductions in the accelerator system cost and improvement in the accelerator system efficiency

Cost/performance analysis of an induction linac driver system for inertial fusion

International Nuclear Information System (INIS)

Hovingh, J.; Brady, V.O.; Faltens, A.; Hoyer, E.H.; Lee, E.P.

1985-11-01

A linear induction accelerator that produces a beam of energetic (approx. =10 GeV) heavy (CAapprox.200) ions is a prime candidate as a driver for inertial fusion. Continuing developments in amorphous iron for use in accelerating modules represent a potentially large reduction in the driver cost and an increase in the driver efficiency. Additional insulator developments may also represent a potentially large reduction in the driver cost. The efficiency and cost of the induction linac system is discussed as a function of output energy and pulse repetition frequency for several beam charge states, numbers of beams and beam particle species. Accelerating modules and transport modules will be described. Large cost leverage items will be identified as a guide to future research activities and technology of development that can yield further substantial reductions in the accelerator system cost and improvement in the accelerator system efficiency. 13 refs., 2 figs

A Context-Aware S-Health Service System for Drivers

Directory of Open Access Journals (Sweden)

Jingkun Chang

2017-03-01

Full Text Available As a stressful and sensitive task, driving can be disturbed by various factors from the health condition of the driver to the environmental variables of the vehicle. Continuous monitoring of driving hazards and providing the most appropriate business services to meet actual needs can guarantee safe driving and make great use of the existing information resources and business services. However, there is no in-depth research on the perception of a driver’s health status or the provision of customized business services in case of various hazardous situations. In order to constantly monitor the health status of the drivers and react to abnormal situations, this paper proposes a context-aware service system providing a configurable architecture for the design and implementation of the smart health service system for safe driving, which can perceive a driver’s health status and provide helpful services to the driver. With the context-aware technology to construct a smart health services system for safe driving, this is the first time that such a service system has been implemented in practice. Additionally, an assessment model is proposed to mitigate the impact of the acceptable abnormal status and, thus, reduce the unnecessary invocation of the services. With regard to different assessed situations, the business services can be invoked for the driver to adapt to hazardous situations according to the services configuration model, which can take full advantage of the existing information resources and business services. The evaluation results indicate that the alteration of the observed status in a valid time range T can be tolerated and the frequency of the service invocation can be reduced.

Driver Drowsiness Warning System Using Visual Information for Both Diurnal and Nocturnal Illumination Conditions

Directory of Open Access Journals (Sweden)

Flores MarcoJavier

2010-01-01

Full Text Available Every year, traffic accidents due to human errors cause increasing amounts of deaths and injuries globally. To help reduce the amount of fatalities, in the paper presented here, a new module for Advanced Driver Assistance System (ADAS which deals with automatic driver drowsiness detection based on visual information and Artificial Intelligence is presented. The aim of this system is to locate, track, and analyze both the drivers face and eyes to compute a drowsiness index, where this real-time system works under varying light conditions (diurnal and nocturnal driving. Examples of different images of drivers taken in a real vehicle are shown to validate the algorithms used.

Behavioral adaptation of young and older drivers to an intersection crossing advisory system

NARCIS (Netherlands)

Dotzauer, Mandy; de Waard, Dick; Caljouw, Simone R.; Poehler, Gloria; Brouwer, Wiebo H.

An advanced driver assistance system (ADAS) provided information about the right of way regulation and safety to cross an upcoming intersection. Effects were studied in a longer-term study involving 18 healthy older drivers between the ages of 65 and 82 years and 18 healthy young drivers between the

Toyota drivers' experiences with Dynamic Radar Cruise Control, Pre-Collision System, and Lane-Keeping Assist.

Science.gov (United States)

Eichelberger, Angela H; McCartt, Anne T

2016-02-01

Advanced crash avoidance and driver assistance technologies potentially can prevent or mitigate many crashes. Previous surveys with drivers have found favorable opinions for many advanced technologies; however, these surveys are not necessarily representative of all drivers or all systems. As the technologies spread throughout the vehicle fleet, it is important to continue studying driver acceptance and use of them. This study focused on 2010-2013 Toyota Sienna and Prius models that were equipped with adaptive cruise control, forward collision avoidance, and lane departure warning and prevention (Prius models only). Telephone interviews were conducted in summer 2013 with 183 owners of vehicles with these technologies. About 9 in 10 respondents wanted adaptive cruise control and forward collision avoidance on their next vehicle, and 71% wanted lane departure warning/prevention again. Males and females reported some differences in their experiences with the systems; for example, males were more likely to have turned on lane departure warning/prevention than females, and when using this system, males reported more frequent warnings than did females. Relative to older drivers, drivers age 40 and younger were more likely to have seen or heard a forward collision warning. Consistent with the results in previous surveys of owners of luxury vehicles, the present survey found that driver acceptance of the technologies was high, although less so for lane departure warning/prevention. Experiences with the Toyota systems differed by driver age and gender to a greater degree than in previous surveys, suggesting that the responses of drivers may begin to differ as crash avoidance technology becomes available on a wider variety of vehicles. Crash avoidance technologies potentially can prevent or mitigate many crashes, but their success depends in part on driver acceptance. These systems will be effective only to the extent that drivers use them. Copyright © 2015 Elsevier Ltd and

INTERACTIVITY OF THE MODERN AUTOMATED SYSTEMS OF THE HELP TO THE DRIVER

OpenAIRE

Svetlana Alekseevna Vasyugova; Andrey Borisovich Nikolaev

2017-01-01

In this article the current technologies in the field of intelligent transportation systems are investigated. The latest systems on control of the safe movement on roads are considered. The analysis of the systems of the help to the driver implemented in cars is carried out. The system concept of the help to the driver of «System help» is offered. Algorithms of work of this system which is based on the principles of interactivity and interaction are investigated. By results of researches expe...

Review of advanced driver assistance systems (ADAS)

Science.gov (United States)

Ziebinski, Adam; Cupek, Rafal; Grzechca, Damian; Chruszczyk, Lukas

2017-11-01

New cars can be equipped with many advanced safety solutions. Airbags, seatbelts and all of the essential passive safety parts are standard equipment. Now cars are often equipped with new advanced active safety systems that can prevent accidents. The functions of the Advanced Driver Assistance Systems are still growing. A review of the most popular available technologies used in ADAS and descriptions of their application areas are discussed in this paper.

Autonomous Driver Based on an Intelligent System of Decision-Making.

Science.gov (United States)

Czubenko, Michał; Kowalczuk, Zdzisław; Ordys, Andrew

The paper presents and discusses a system ( xDriver ) which uses an Intelligent System of Decision-making (ISD) for the task of car driving. The principal subject is the implementation, simulation and testing of the ISD system described earlier in our publications (Kowalczuk and Czubenko in artificial intelligence and soft computing lecture notes in computer science, lecture notes in artificial intelligence, Springer, Berlin, 2010, 2010, In Int J Appl Math Comput Sci 21(4):621-635, 2011, In Pomiary Autom Robot 2(17):60-5, 2013) for the task of autonomous driving. The design of the whole ISD system is a result of a thorough modelling of human psychology based on an extensive literature study. Concepts somehow similar to the ISD system can be found in the literature (Muhlestein in Cognit Comput 5(1):99-105, 2012; Wiggins in Cognit Comput 4(3):306-319, 2012), but there are no reports of a system which would model the human psychology for the purpose of autonomously driving a car. The paper describes assumptions for simulation, the set of needs and reactions (characterizing the ISD system), the road model and the vehicle model, as well as presents some results of simulation. It proves that the xDriver system may behave on the road as a very inexperienced driver.

The effects of driver identity on driving safety in a retrospective feedback system.

Science.gov (United States)

Zhao, Guozhen; Wu, Changxu

2012-03-01

Retrospective feedback that provides detailed information on a driver's performance in critical driving situations at the end of a trip enhances his/her driving behaviors and safe driving habits. Although this has been demonstrated by a previous study, retrospective feedback can be further improved and applied to non-critical driving situations, which is needed for transportation safety. To propose a new retrospective feedback system that uses driver identity (i.e., a driver's name) and to experimentally study its effects on measures of driving performance and safety in a driving simulator. We conducted a behavioral experimental study with 30 participants. "Feedback type" was a between-subject variable with three conditions: no feedback (control group), feedback without driver identity, and feedback with driver identity. We measured multiple aspects of participants' driving behavior. To control for potential confounds, factors that were significantly correlated with driving behavior (e.g., age and driving experience) were all entered as covariates into a multivariate analysis of variance. To examine the effects of speeding on collision severity in driving simulation studies, we also developed a new index - momentum of potential collision - with a set of equations. Subjects who used a feedback system with driver identity had the fewest speeding violations and central-line crossings, spent the least amount of time speeding and crossing the central line, had the lowest speeding and central-line crossing magnitude, ran the fewest red lights, and had the smallest momentum of potential collision compared to the groups with feedback without driver identity and without feedback (control group). The new retrospective feedback system with driver identity has the potential to enhance a person's driving safety (e.g., speeding, central-line crossing, momentum of potential collision), which is an indication of the valence of one's name in a feedback system design. Copyright �

The driver as archetype for driver assistance systems? A driver-model based approach for the development of situation-adaptive DAS; Der Fahrer als Vorbild fuer Fahrerassistenzsysteme? Ein Fahrermodellbasierter Ansatz zur Entwicklung von situationsadaptiven FAS

Energy Technology Data Exchange (ETDEWEB)

Benmimoun, A. [Inst. fuer Kraftfahrwesen, RWTH-Aachen, Aachen (Germany)

2004-07-01

A new approach for the development of advanced driver assistance systems is presented. The keynote of this new approach is to use the driver model of the traffic simulation tool PELOPS as a control algorithm and to apply it to a vehicle. The fact, that the human driving behaviour is the starting point of the development, is the main advantage of this new approach. Thus important aspects for the development of driver assistance systems like a situation-adaptive and reliable control, understandable behaviour and the consideration of driver-individual parameters are integrated in the controller design from the beginning. An application example of the new approach is shown. (orig.)

Factors influencing compliance to tactical driver advice: an assessment using a think-aloud protocol

NARCIS (Netherlands)

Risto, Malte; Martens, Marieke Hendrikje

2013-01-01

Connected Cruise Control (CCC) is an in-car driver support systems that aims to improve throughput in dense motorway traffic by advising drivers how to drive. The system is currently under development within a HTAS project. It will integrate lane advice, headway advice and speed advice. CCC will not

INTERACTIVITY OF THE MODERN AUTOMATED SYSTEMS OF THE HELP TO THE DRIVER

Directory of Open Access Journals (Sweden)

Svetlana Alekseevna Vasyugova

2017-09-01

Full Text Available In this article the current technologies in the field of intelligent transportation systems are investigated. The latest systems on control of the safe movement on roads are considered. The analysis of the systems of the help to the driver implemented in cars is carried out. The system concept of the help to the driver of «System help» is offered. Algorithms of work of this system which is based on the principles of interactivity and interaction are investigated. By results of researches experiment on quality of work of system concept of «System help» is made.

State of the art Advanced Driver Assistance Systems (ADAS).

NARCIS (Netherlands)

OEI, H.-L.

2017-01-01

An overview of state-of-the-art ADA Advanced Driver Assistance systems is given. First a main structuring system for the ADA systems is presented, needed for purposes of relevancy, and consistency : the three phases in the accident process, i.e. pre-crash, crash and post-crash; the driving task at

Parental perceptions of the learner driver log book system in two Australian states.

Science.gov (United States)

Bates, Lyndel; Watson, Barry; King, Mark Johann

2014-01-01

Though many jurisdictions internationally now require learner drivers to complete a specified number of hours of supervised driving practice before being able to drive unaccompanied, very few require learner drivers to complete a log book to record this practice and then present it to the licensing authority. Learner drivers in most Australian jurisdictions must complete a log book that records their practice, thereby confirming to the licensing authority that they have met the mandated hours of practice requirement. These log books facilitate the management and enforcement of minimum supervised hours of driving requirements. Parents of learner drivers in 2 Australian states, Queensland and New South Wales, completed an online survey assessing a range of factors, including their perceptions of the accuracy of their child's learner log book and the effectiveness of the log book system. The study indicates that the large majority of parents believe that their child's learner log book is accurate. However, they generally report that the log book system is only moderately effective as a system to measure the number of hours of supervised practice a learner driver has completed. The results of this study suggest the presence of a paradox, with many parents possibly believing that others are not as diligent in the use of log books as they are or that the system is too open to misuse. Given that many parents report that their child's log book is accurate, this study has important implications for the development and ongoing monitoring of hours of practice requirements in graduated driver licensing systems.

Google glass: a driver distraction cause or cure?

Science.gov (United States)

Sawyer, Ben D; Finomore, Victor S; Calvo, Andres A; Hancock, P A

2014-11-01

We assess the driving distraction potential of texting with Google Glass (Glass), a mobile wearable platform capable of receiving and sending short-message-service and other messaging formats. A known roadway danger, texting while driving has been targeted by legislation and widely banned. Supporters of Glass claim the head-mounted wearable computer is designed to deliver information without concurrent distraction. Existing literature supports the supposition that design decisions incorporated in Glass might facilitate messaging for drivers. We asked drivers in a simulator to drive and use either Glass or a smartphone-based messaging interface, then interrupted them with an emergency brake event. Both the response event and subsequent recovery were analyzed. Glass-delivered messages served to moderate but did not eliminate distracting cognitive demands. A potential passive cost to drivers merely wearing Glass was also observed. Messaging using either device impaired driving as compared to driving without multitasking. Glass in not a panacea as some supporters claim, but it does point the way to design interventions that effect reduced load in multitasking. Discussions of these identified benefits are framed within the potential of new in-vehicle systems that bring both novel forms of distraction and tools for mitigation into the driver's seat.

Reduction of low frequency vibration of truck driver and seating system through system parameter identification, sensitivity analysis and active control

Science.gov (United States)

Wang, Xu; Bi, Fengrong; Du, Haiping

2018-05-01

This paper aims to develop an 5-degree-of-freedom driver and seating system model for optimal vibration control. A new method for identification of the driver seating system parameters from experimental vibration measurement has been developed. The parameter sensitivity analysis has been conducted considering the random excitation frequency and system parameter uncertainty. The most and least sensitive system parameters for the transmissibility ratio have been identified. The optimised PID controllers have been developed to reduce the driver's body vibration.

Availability of Life Support Equipment and its Utilization by Ambulance Drivers.

Science.gov (United States)

Acharya, Rija; Badhu, Angur; Shah, Tara; Shrestha, Sharmila

2017-09-08

An effective ambulance is a vital requirement for providing an emergency medical service. Well-equipped ambulances with trained paramedics can save many lives during the golden hours of trauma care. The objective was to document the availability and utilization of basic life support equipment in the ambulances and to assess knowledge on first aid among the drivers. Descriptive design was used. Total of 109 ambulances linked to B.P. Koirala Institute of Health Sciences were enrolled using purposive sampling method. Self- constructed observation checklist and semi structured interview schedule was used for data collection. More than half of the respondents had less than five years of experience and were not trained in first aid. About two-third of the respondents had adequate knowledge on first aid. About 90% of the ambulance had oxygen cylinder and adult oxygen mask which was 'usually' used equipment. More than half of ambulance had equipment less than 23% as compared to that of national guidelines. There was significant association of knowledge with the experience (p = 0.004) and training (p = 0.001). Availability of equipment was associated with training received (p = 0.007),organization (p= 0.032)and district (p = 0.023) in which the ambulance is registered. The study concludes that maximum ambulance linked to BPKIHS, Nepal did not have even one fourth of the equipment for basic life support. Equipment usually used was oxygen cylinder and oxygen mask. Majority of driver had adequate knowledge on first aid and it was associated with training and experience.

Evaluation of ADAS with a supported-driver model for desired allocation of tasks between human and technology performance

NARCIS (Netherlands)

van den Beukel, Arie Paul; van der Voort, Mascha C.; Meyer, G.; Valldorf, J.

2009-01-01

Partly automated driving is relevant for solving mobility problems, but also causes concerns with respect to the driver‟s reliability in task performance. The supported driver model presented in this paper is therefore intended to answer the question, what type of support and in which circumstances,

Acoustic Levitation With One Driver

Science.gov (United States)

Wang, T. G.; Rudnick, I.; Elleman, D. D.; Stoneburner, J. D.

1985-01-01

Report discusses acoustic levitation in rectangular chamber using one driver mounted at corner. Placement of driver at corner enables it to couple effectively to acoustic modes along all three axes. Use of single driver reduces cost, complexity and weight of levitation system below those of three driver system.

Effects of Self-Efficacy on Healthy Eating Depends on Normative Support: a Prospective Study of Long-Haul Truck Drivers.

Science.gov (United States)

Hamilton, Kyra; Hagger, Martin S

2018-04-01

Fruit and vegetable intake (FV) is insufficient in industrialized nations and there is excess of discretionary food choices (DC; foods high in fat, sugar, and salt). Long-haul truck drivers are considered a particularly at-risk group given the limited food choices and normatively reinforced eating habits at truck rest-stops. Self-efficacy and normative support are key determinants of eating behavior yet the processes underlying their effects on behavior are not well understood. We tested the direct and interactive effects of self-efficacy and normative support on healthy eating behaviors in long-haul truck drivers in a prospective correlational study. Long-haul truck drivers (N = 82) completed an initial survey containing self-report measures of behavioral intentions, perceived normative support, and self-efficacy for their FV and DC behaviors. Participants completed a follow-up survey 1 week later in which they self-reported their FV and DC behavior. A mediated moderation analysis identified an interactive effect of self-efficacy and normative support on behavior mediated by intention for FV and DC behavior. Specifically, we confirmed a compensation effect in which self-efficacy was more likely to have an effect on FV and DC behavior through intentions in participants with low normative support. Results indicate the importance of self-efficacy in predicting FV and DC intentions and behavior in the absence of a supportive normative environment. The compensatory effect of self-efficacy beliefs on behavior through intentions when normative support is low should be confirmed using experimental methods.

Modeling driver stop/run behavior at the onset of a yellow indication considering driver run tendency and roadway surface conditions.

Science.gov (United States)

Elhenawy, Mohammed; Jahangiri, Arash; Rakha, Hesham A; El-Shawarby, Ihab

2015-10-01

The ability to model driver stop/run behavior at signalized intersections considering the roadway surface condition is critical in the design of advanced driver assistance systems. Such systems can reduce intersection crashes and fatalities by predicting driver stop/run behavior. The research presented in this paper uses data collected from two controlled field experiments on the Smart Road at the Virginia Tech Transportation Institute (VTTI) to model driver stop/run behavior at the onset of a yellow indication for different roadway surface conditions. The paper offers two contributions. First, it introduces a new predictor related to driver aggressiveness and demonstrates that this measure enhances the modeling of driver stop/run behavior. Second, it applies well-known artificial intelligence techniques including: adaptive boosting (AdaBoost), random forest, and support vector machine (SVM) algorithms as well as traditional logistic regression techniques on the data in order to develop a model that can be used by traffic signal controllers to predict driver stop/run decisions in a connected vehicle environment. The research demonstrates that by adding the proposed driver aggressiveness predictor to the model, there is a statistically significant increase in the model accuracy. Moreover the false alarm rate is significantly reduced but this reduction is not statistically significant. The study demonstrates that, for the subject data, the SVM machine learning algorithm performs the best in terms of optimum classification accuracy and false positive rates. However, the SVM model produces the best performance in terms of the classification accuracy only. Copyright © 2015 Elsevier Ltd. All rights reserved.

Adaptive object placement for augmented reality use in driver assistance systems

OpenAIRE

Bordes, Lucie; Breckon, Toby P.; Katramados, Ioannis; Kheyrollahi, Alireza

2011-01-01

We present an approach for adaptive object placement for Augmented Reality (AR) use in driver assistance systems. Combined vanishing point and road surface detection enable the real-time adaptive emplacement of AR objects within a drivers' natural field of view for on-road information display. This work combines both automotive vision and multimedia production aspects of real-time visual engineering.

Fighting against a shortage of truck drivers in logistics: Measures that employers can take to promote drivers' work ability and health.

Science.gov (United States)

Staats, Ulrike; Lohaus, Daniela; Christmann, Alina; Woitschek, Michèle

2017-01-01

For several years, the transportation industry has been concerned about a severe shortage of professional truck drivers. Studies investigating the reasons found that poor working conditions and stresses and strains resulting from physiological and psychological job demands have had a negative impact on drivers' health and ability to work. Nevertheless, until now, most employers have refrained from offering measures to support the work ability and well-being of drivers, mainly due to financial pressures in the industry. The present study was aimed at designing adequate and affordable measures to support drivers' health. With reference to the Work Ability Index and the house of work ability (Ilmarinen & Tuomi, 2004), 56 truck drivers participated in guided interviews about their working conditions and health-related problems as well as their attitudes, experiences, and desires with respect to being offered supportive measures by their employers. The measures derived are specific and realizable and expected to be widely accepted by professional drivers. They are designed to elicit a positive attitude in the drivers toward exercising and to help them overcome related psychological barriers. The implementation of the recommended measures can be expected to support drivers' work ability and help reduce the frictional costs of their employers.

Creating a smart application system to provide a beneficial maintenance service for elderly drivers

Directory of Open Access Journals (Sweden)

Jung Sebin

2017-01-01

Full Text Available As overall population ages, elderly drivers have become a larger percentage of the driving population. With this trend, a lot of vehicle systems have been improved for elderly’s safety and convenience using different advanced technologies. However, elderly drivers have often paid more money than other drivers in a car-repair shop due to their lack of knowledge about vehicle systems with modern technologies. Given this fact, developing a tool to diminish this disadvantage and to help elderly drivers maintain their cars with confidence and with minimal cost is necessary. Therefore, this research work mainly focuses on suggesting a system concept on user-interface application, which is connected to a smart phone or a tablet to provide beneficial services anywhere. For the research outcome, diverse research activities – surveys, interviews with small focus groups, observations of the focus groups, and discussions – has been conducted to understand the elderly driver’s difficulties and behaviours regarding vehicle maintenance, to investigate what specific problems make them uncomfortable in repair shops, and to demonstrate how new system-concepts could be developed for the elderly. Furthermore, we conclude that adequate system-concepts for the elderly would offer elderly drivers convenient vehicle repair and maintenance and provide them a confident driving experience.

Traffic modelling validation of advanced driver assistance systems

NARCIS (Netherlands)

Tongeren, R. van; Gietelink, O.J.; Schutter, B. de; Verhaegen, M.

2007-01-01

This paper presents a microscopic traffic model for the validation of advanced driver assistance systems. This model describes single-lane traffic and is calibrated with data from a field operational test. To illustrate the use of the model, a Monte Carlo simulation of single-lane traffic scenarios

Drivers and challenges for implementing ISO 14001 environmental management systems in an emerging Gulf Arab country.

Science.gov (United States)

Waxin, Marie-France; Knuteson, Sandra L; Bartholomew, Aaron

2017-11-13

Worldwide, ISO 14001 certification for organizations has become the norm, but the Arab world accounts for an insignificant portion of all the certified organizations. There is a dearth of research on environmental management systems (EMS) in Arab and emerging countries and in public organizations. The objectives of this research are to: (1) examine the key drivers and challenges related to implementation of ISO 14001 certified EMS in the United Arab Emirates, an emerging Arab country and (2) compare and contrast these drivers and challenges between private and public organizations. We adopt an explorative, qualitative methodology, using semi-structured interviews with environmental managers in 11 organizations (6 private and 5 public) from different industrial sectors. Drivers of EMS certification were mostly similar between private and public organizations, with some differences. Compliance with regulations and standards, and increasing environmental performance were the main drivers for ISO 14001 certification in both private and public organizations. Commitment to sustainability was more important for public organizations. Cost reduction, competitors, leadership commitment and customers' demands were shared drivers, but more stressed by private organizations. Local community and employees' pressures were reported by private organizations only. The challenges to ISO 14001 implementation were similar for private and public organizations. They were: a lack of qualified human resources, practical challenges associated with implementation, a lack of regulations, a lack of support from management, and high costs. Our findings have implications for managers, academics, consultants, and policy makers in the UAE and other emerging markets.

Kin-Driver: a database of driver mutations in protein kinases.

Science.gov (United States)

Simonetti, Franco L; Tornador, Cristian; Nabau-Moretó, Nuria; Molina-Vila, Miguel A; Marino-Buslje, Cristina

2014-01-01

Somatic mutations in protein kinases (PKs) are frequent driver events in many human tumors, while germ-line mutations are associated with hereditary diseases. Here we present Kin-driver, the first database that compiles driver mutations in PKs with experimental evidence demonstrating their functional role. Kin-driver is a manual expert-curated database that pays special attention to activating mutations (AMs) and can serve as a validation set to develop new generation tools focused on the prediction of gain-of-function driver mutations. It also offers an easy and intuitive environment to facilitate the visualization and analysis of mutations in PKs. Because all mutations are mapped onto a multiple sequence alignment, analogue positions between kinases can be identified and tentative new mutations can be proposed for studying by transferring annotation. Finally, our database can also be of use to clinical and translational laboratories, helping them to identify uncommon AMs that can correlate with response to new antitumor drugs. The website was developed using PHP and JavaScript, which are supported by all major browsers; the database was built using MySQL server. Kin-driver is available at: http://kin-driver.leloir.org.ar/ © The Author(s) 2014. Published by Oxford University Press.

Design of laser diode driver with constant current and temperature control system

Science.gov (United States)

Wang, Ming-cai; Yang, Kai-yong; Wang, Zhi-guo; Fan, Zhen-fang

2017-10-01

A laser Diode (LD) driver with constant current and temperature control system is designed according to the LD working characteristics. We deeply researched the protection circuit and temperature control circuit based on thermos-electric cooler(TEC) cooling circuit and PID algorithm. The driver could realize constant current output and achieve stable temperature control of LD. Real-time feedback control method was adopted in the temperature control system to make LD work on its best temperature point. The output power variety and output wavelength shift of LD caused by current and temperature instability were decreased. Furthermore, the driving current and working temperature is adjustable according to specific requirements. The experiment result showed that the developed LD driver meets the characteristics of LD.

Drivers' smart advisory system improves driving performance at STOP sign intersections

Directory of Open Access Journals (Sweden)

Qing Li

2017-06-01

Full Text Available STOP signs are often physically blocked by obstacles at the corner, forming a safety threat. To enhance the safety at an un-signalized intersection like a STOP sign intersection, a radio frequency identification (RFID based drivers smart advisory system (DSAS was developed, which provides drivers with an earlier warning message when they are approaching an un-signalized intersection. In this research, a pilot field test was conducted with the DSAS alarm on an approach towards a STOP sign intersection in a residential area in Houston, Texas. The designed test route covers all turning movements, including left turn, through movement, and right turn. GPS units recorded test drivers' driving behaviors. A self-developed MATLAB program and statistically significant difference t-test were applied to analyze the impacts of the DSAS messages on drivers' driving performance, in terms of approaching speed profile, acceleration/deceleration rates, braking distance, and possible extra vehicle emissions induced by the introduction of the DSAS message. Drivers' preference on the DSAS was investigated by a designed survey questionnaire among test drivers. Results showed that the DSAS alarm was able to induce drivers to drive significantly slower to approach a STOP sign intersection, perform smaller fluctuation in acceleration/deceleration rates, and be more aware of a coming STOP sign indicated by decelerating earlier. All test drivers preferred to follow the DSAS alarm on roads for a safety concern. Further, the DSAS alarm caused the reduction in emission rates through movement. For a general observation, more road tests with more participants and different test routes were recommended.

Driver assistance systems - status and future prospects; Fahrerassistenzsysteme fuer Nutzfahrzeuge - Stand und Ausblick

Energy Technology Data Exchange (ETDEWEB)

Hipp, E.; Schaller, K.V. [MAN Nutzfahrzeuge AG, Muenchen (Germany)

2001-07-01

Driver assistance systems help the driver in his work. The demand for such systems will be determined by the marked increase in traffic on our roads and also the growing requirements on drivers of commercial vehicles. These systems are basically understood to be systems which assist navigation, the selection and retention of driving values and the stabilisation with regard to the vehicle and its surroundings. They include - Adaptive cruise control, - stop and go systems, - vehicle to vehicle communication, - lane guard system, - turn-off assistance. New approaches to ease the driver's burden, improve traffic flow and safety will be discussed and - as far as possible - assessed. Their use, acceptance and legal questions are to be presented against a background of long-term evaluation, system limits and functional transparency. (orig.) [German] Fahrerassistenzsysteme helfen dem Fahrer bei seinen Aufgaben. Die deutlichen Veraenderungen im Verkehrsgeschehen auf unseren Strassen aber auch die gestiegenen Anforderungen an den Fahrer von Nutzfahrzeugen werden die Nachfrage nach solchen Systemen bestimmen. Grundsaetzlich werden hier Systeme verstanden, die assistieren bei der Navigation, der Wahl und Einhaltung der Fuehrungsgroessen und bei der Stabilisierung im Umfeld von Fahrzeug und von Fahrumgebung. Betrachtet werden - Adaptive Cruise Control, - Stop and Go-Systeme, - Fahrzeug-Fahrzeug Kommunikation, - Lane Guard System, - Abbiegeassistenz und weiterfuehrende, - Telematiksysteme. Neue Ansaetze, die zur Entlastung des Fahrers, zu Verbesserungen im Verkehrsfluss und der Fahrsicherheit fuehren werden diskutiert und - soweit moeglich - bewertet. Nutzung, Akzeptanz, rechtliche Fragen sollen vor dem Hintergrund von Langzeitbewertung, Systemgrenzen und Funktionstransparenz dargestellt werden. (orig.)

On-Road Driver Monitoring System Based on a Solar-Powered In-Vehicle Embedded Platform

Directory of Open Access Journals (Sweden)

Yen-Lin Chen

2014-01-01

Full Text Available This study presents an on-road driver monitoring system, which is implemented on a stand-alone in-vehicle embedded system and driven by effective solar cells. The driver monitoring function is performed by an efficient eye detection technique. Through the driver’s eye movements captured from the camera, the attention states of the driver can be determined and any fatigue states can be avoided. This driver monitoring technique is implemented on a low-power embedded in-vehicle platform. Besides, this study also proposed monitoring machinery that can detect the brightness around the car to effectively determine whether this in-vehicle system is driven by the solar cells or by the vehicle battery. On sunny days, the in-vehicle system can be powered by solar cell in places without the vehicle battery. While in the evenings or on rainy days, the ambient solar brightness is insufficient, and the system is powered by the vehicle battery. The proposed system was tested under the conditions that the solar irradiance is 10 to 113 W/m2 and solar energy and brightness at 10 to 170. From the testing results, when the outside solar radiation is high, the brightness of the inside of the car is increased, and the eye detection accuracy can also increase as well. Therefore, this solar powered driver monitoring system can be efficiently applied to electric cars to save energy consumption and promote the driving safety.

Technological drivers in data centers and telecom systems: Multiscale thermal, electrical, and energy management

International Nuclear Information System (INIS)

Garimella, Suresh V.; Persoons, Tim; Weibel, Justin; Yeh, Lian-Tuu

2013-01-01

Highlights: ► Thermal management approaches reviewed against energy usage of IT industry. ► Challenges of energy efficiency in large-scale electronic systems highlighted. ► Underlying drivers for progress at the business and technology levels identified. ► Thermal, electrical and energy management challenges discussed as drivers. ► Views of IT system operators, manufacturers and integrators represented. - Abstract: We identify technological drivers for tomorrow’s data centers and telecommunications systems, including thermal, electrical and energy management challenges, based on discussions at the 2nd Workshop on Thermal Management in Telecommunication Systems and Data Centers in Santa Clara, California, on April 25–26, 2012. The relevance of thermal management in electronic systems is reviewed against the background of the energy usage of the information technology (IT) industry, encompassing perspectives of different sectors of the industry. The underlying drivers for progress at the business and technology levels are identified. The technological challenges are reviewed in two main categories – immediate needs and future needs. Enabling cooling techniques that are currently under development are also discussed

Driver assistance system for lane departure avoidance by steering and differential braking

OpenAIRE

MINOIU-ENACHE, N; MAMMAR, S; GLASER, S; LUSETTI, B

2010-01-01

Lane departure avoidance systems assist actively the driver during inattention or drowsiness and increase driving safety. Most of the lane departure avoidance systems use for the lateral control of the vehicle in closed loop a DC motor similar to the electrical powered steering (EPS) assistance. Important difficulties and limits of this approach are the shared control with the driver on the steering wheel and the vehicle handling at limits. In this paper a combined lateral control using a DC ...

Global drivers, sustainable manufacturing and systems ergonomics.

Science.gov (United States)

Siemieniuch, C E; Sinclair, M A; Henshaw, M J deC

2015-11-01

This paper briefly explores the expected impact of the 'Global Drivers' (such as population demographics, food security; energy security; community security and safety), and the role of sustainability engineering in mitigating the potential effects of these Global Drivers. The message of the paper is that sustainability requires a significant input from Ergonomics/Human Factors, but the profession needs some expansion in its thinking in order to make this contribution. Creating a future sustainable world in which people experience an acceptable way of life will not happen without a large input from manufacturing industry into all the Global Drivers, both in delivering products that meet sustainability criteria (such as durability, reliability, minimised material requirement and low energy consumption), and in developing sustainable processes to deliver products for sustainability (such as minimum waste, minimum emissions and low energy consumption). Appropriate changes are already being implemented in manufacturing industry, including new business models, new jobs and new skills. Considerable high-level planning around the world is in progress and is bringing about these changes; for example, there is the US 'Advanced Manufacturing National Program' (AMNP)', the German 'Industrie 4.0' plan, the French plan 'la nouvelle France industrielle' and the UK Foresight publications on the 'Future of Manufacturing'. All of these activities recognise the central part that humans will continue to play in the new manufacturing paradigms; however, they do not discuss many of the issues that systems ergonomics professionals acknowledge. This paper discusses a number of these issues, highlighting the need for some new thinking and knowledge capture by systems ergonomics professionals. Among these are ethical issues, job content and skills issues. Towards the end, there is a summary of knowledge extensions considered necessary in order that systems ergonomists can be fully

Design methodology for fault-tolerant control of advanced driver assistance systems

NARCIS (Netherlands)

Gietelink, O.J.; Ploeg, J.; Schutter, B. de; Verhaegen, M.H.G.

2003-01-01

The objective of this project is to develop a methodology for the design, testing, evaluation and implementation of control systems for Advanced Driver Assistance Systems (ADAS). Examples of ADAS are collision avoidance systems, lane departure warning systems, pre-crash sensing, and adaptive cruise

Examination of supplemental driver training and online basic driver education courses : traffic tech.

Science.gov (United States)

2012-08-01

The first six months of unsupervised driving are the most : hazardous in a novice drivers driving experience. Most : States adopted graduated driver licensing (GDL) systems : to give novice drivers experience in a protective environment, : gradual...

Coping with the worrying complexity of cooperative driver assistance systems

NARCIS (Netherlands)

Ouden, F.C. den; Papp, Z.; Zoutendijk, A.M.; Netten, B.D.; Agovic, K.

2006-01-01

In recent years a clear trend became visible towards vehicles equipped with intelligent driver assistance systems based on cooperation between vehicle and infrastructure. The main reason for this is the high potential cooperative systems show to increase traffic throughput and safety and to decrease

Development of Ethernet emulation driver for reflective memory

International Nuclear Information System (INIS)

Seo, Seong-Heon

2010-01-01

Reflective memory (RFM) is adopted as a real time network in the KSTAR plasma control system (PCS). Since the data uploaded from any computer are automatically shared among all the computers on the RFM network, the design of a distributed control system based on RFM is easily implemented through the management of memory mapping. The data providers and consumers are logically well seperated so that, if memory mapping information is given, a new control unit can be added without any modification to the existing system except connecting a new RFM module through an optical cable. The KSTAR PCS is also connected with the Ethernet in addition to the RFM because the RFM does not support the Transmission Control Protocol/Internet Protocol (TCP/IP) and many network services of the operating system such as the Network File System (NFS) and the Secure Shell (SSH) are based on the TCP/IP. Therefore we developed an Ethernet emulation driver for the RFM to eliminate the need for a separate Ethernet network. The driver was tested on the Linux kernel 2.6.31. The algorithm of the emulation driver is explained and the experimental setup is presented.

A CRITICAL OVERVIEW OF DRIVER INFORMATION SYSTEMS; THE NEED IN LARGE CITIES

Directory of Open Access Journals (Sweden)

Banihan GÜNAY

1998-01-01

Full Text Available The growth of traffic has exacerbated a number of problems like congestion and delay. In the field of dynamic traffic management, providing systems that disseminate necessary information to drivers and guide traffic according to the most efficient paths considering the current traffic conditions has been a central idea. Information technology gained predominance as the limitations of traditional traffic engineering became apparent. This paper elaborates on Driver Information and reviews critically current technologies available. Need for the applications of such systems is also addressed.

Driver Fatigue Detection System Using Electroencephalography Signals Based on Combined Entropy Features

Directory of Open Access Journals (Sweden)

Zhendong Mu

2017-02-01

Full Text Available Driver fatigue has become one of the major causes of traffic accidents, and is a complicated physiological process. However, there is no effective method to detect driving fatigue. Electroencephalography (EEG signals are complex, unstable, and non-linear; non-linear analysis methods, such as entropy, maybe more appropriate. This study evaluates a combined entropy-based processing method of EEG data to detect driver fatigue. In this paper, 12 subjects were selected to take part in an experiment, obeying driving training in a virtual environment under the instruction of the operator. Four types of enthrones (spectrum entropy, approximate entropy, sample entropy and fuzzy entropy were used to extract features for the purpose of driver fatigue detection. Electrode selection process and a support vector machine (SVM classification algorithm were also proposed. The average recognition accuracy was 98.75%. Retrospective analysis of the EEG showed that the extracted features from electrodes T5, TP7, TP8 and FP1 may yield better performance. SVM classification algorithm using radial basis function as kernel function obtained better results. A combined entropy-based method demonstrates good classification performance for studying driver fatigue detection.

Big Data as a Driver for Clinical Decision Support Systems: A Learning Health Systems Perspective

Directory of Open Access Journals (Sweden)

Arianna Dagliati

2018-05-01

Full Text Available Big data technologies are nowadays providing health care with powerful instruments to gather and analyze large volumes of heterogeneous data collected for different purposes, including clinical care, administration, and research. This makes possible to design IT infrastructures that favor the implementation of the so-called “Learning Healthcare System Cycle,” where healthcare practice and research are part of a unique and synergic process. In this paper we highlight how “Big Data enabled” integrated data collections may support clinical decision-making together with biomedical research. Two effective implementations are reported, concerning decision support in Diabetes and in Inherited Arrhythmogenic Diseases.

Prediction of Driver's Intention of Lane Change by Augmenting Sensor Information Using Machine Learning Techniques.

Science.gov (United States)

Kim, Il-Hwan; Bong, Jae-Hwan; Park, Jooyoung; Park, Shinsuk

2017-06-10

Driver assistance systems have become a major safety feature of modern passenger vehicles. The advanced driver assistance system (ADAS) is one of the active safety systems to improve the vehicle control performance and, thus, the safety of the driver and the passengers. To use the ADAS for lane change control, rapid and correct detection of the driver's intention is essential. This study proposes a novel preprocessing algorithm for the ADAS to improve the accuracy in classifying the driver's intention for lane change by augmenting basic measurements from conventional on-board sensors. The information on the vehicle states and the road surface condition is augmented by using an artificial neural network (ANN) models, and the augmented information is fed to a support vector machine (SVM) to detect the driver's intention with high accuracy. The feasibility of the developed algorithm was tested through driving simulator experiments. The results show that the classification accuracy for the driver's intention can be improved by providing an SVM model with sufficient driving information augmented by using ANN models of vehicle dynamics.

Economic and Cultural Drivers of Immigrant Support Worldwide

DEFF Research Database (Denmark)

Valentino, Nicholas A.; Soroka, Stuart N.; Iyengar, Shanto

2017-01-01

Employing a comparative experimental design drawing on over 18,000 interviews across eleven countries on four continents, this article revisits the discussion about the economic and cultural drivers of attitudes towards immigrants in advanced democracies. Experiments manipulate the occupational...

Modelling Supported Driving as an Optimal Control Cycle : Framework and Model Characteristics

NARCIS (Netherlands)

Wang, M.; Treiber, M.; Daamen, W.; Hoogendoorn, S.P.; Van Arem, B.

2013-01-01

Driver assistance systems support drivers in operating vehicles in a safe, comfortable and efficient way, and thus may induce changes in traffic flow characteristics. This paper puts forward a receding horizon control framework to model driver assistance and cooperative systems. The accelerations of

OLDER DRIVERS AND ADAS

Directory of Open Access Journals (Sweden)

Ragnhild J. DAVIDSE

2006-01-01

Next, based on the available literature, relevant ADAS are discussed in terms of their availability, their effects on safety and the willingness of older drivers to use and buy them. One of the conclusions is that only very few of the types of support that are thought to be most beneficial to the safety of older drivers are provided by the ADAS that are currently available.

Decision support systems in water and wastewater treatment process selection and design: a review.

Science.gov (United States)

Hamouda, M A; Anderson, W B; Huck, P M

2009-01-01

The continuously changing drivers of the water treatment industry, embodied by rigorous environmental and health regulations and the challenge of emerging contaminants, necessitates the development of decision support systems for the selection of appropriate treatment trains. This paper explores a systematic approach to developing decision support systems, which includes the analysis of the treatment problem(s), knowledge acquisition and representation, and the identification and evaluation of criteria controlling the selection of optimal treatment systems. The objective of this article is to review approaches and methods used in decision support systems developed to aid in the selection, sequencing of unit processes and design of drinking water, domestic wastewater, and industrial wastewater treatment systems. Not surprisingly, technical considerations were found to dominate the logic of the developed systems. Most of the existing decision-support tools employ heuristic knowledge. It has been determined that there is a need to develop integrated decision support systems that are generic, usable and consider a system analysis approach.

State-of-the-art Versus Time-triggered Object Tracking in Advanced Driver Assistance Systems

Directory of Open Access Journals (Sweden)

Moritz Koplin

2013-04-01

Full Text Available Most state-of-the-art driver assistance systems cannot guarantee that real-time images of object states are updated within a given time interval, because the object state observations are typically sampled by uncontrolled sensors and transmitted via an indeterministic bus system such as CAN. To overcome this shortcoming, a paradigm shift toward time-triggered advanced driver assistance systems based on a deterministic bus system, such as FlexRay, is under discussion. In order to prove the feasibility of this paradigm shift, this paper develops different models of a state-of-the-art and a time-triggered advanced driver assistance system based on multi-sensor object tracking and compares them with regard to their mean performance. The results show that while the state-of-the-art model is advantageous in scenarios with low process noise, it is outmatched by the time-triggered model in the case of high process noise, i.e., in complex situations with high dynamic.

An Orientation Sensor-Based Head Tracking System for Driver Behaviour Monitoring

Directory of Open Access Journals (Sweden)

Yifan Zhao

2017-11-01

Full Text Available Although at present legislation does not allow drivers in a Level 3 autonomous vehicle to engage in a secondary task, there may become a time when it does. Monitoring the behaviour of drivers engaging in various non-driving activities (NDAs is crucial to decide how well the driver will be able to take over control of the vehicle. One limitation of the commonly used face-based head tracking system, using cameras, is that sufficient features of the face must be visible, which limits the detectable angle of head movement and thereby measurable NDAs, unless multiple cameras are used. This paper proposes a novel orientation sensor based head tracking system that includes twin devices, one of which measures the movement of the vehicle while the other measures the absolute movement of the head. Measurement error in the shaking and nodding axes were less than 0.4°, while error in the rolling axis was less than 2°. Comparison with a camera-based system, through in-house tests and on-road tests, showed that the main advantage of the proposed system is the ability to detect angles larger than 20° in the shaking and nodding axes. Finally, a case study demonstrated that the measurement of the shaking and nodding angles, produced from the proposed system, can effectively characterise the drivers’ behaviour while engaged in the NDAs of chatting to a passenger and playing on a smartphone.

DRIVING IN EMERGENCIES WITH USE OF SYSTEM OF THE HELP TO THE DRIVER

Directory of Open Access Journals (Sweden)

Svetlana Alekseevna Vasyugova

2017-05-01

Full Text Available The purpose of this article consists in research of modern technologies in automotive industry by the analysis and carrying out technical experiment. The main attention concentrates on traffic safety, which is carried out by automation and modernization of vehicles. In article innovative solutions on implementation of the safe movement of the car are considered. The system of the help to the driver in emergencies of “System help” is offered. This system is intended for implementation of automation of certain processes of the car at those moments of the movement when the driver ignores or doesn’t notice the informing signals of system.

Motivational Interviewing support for a behavioral health internet intervention for drivers with type 1 diabetes

Directory of Open Access Journals (Sweden)

Karen S. Ingersoll

2015-05-01

Full Text Available While Internet interventions can improve health behaviors, their impact is limited by program adherence. Supporting program adherence through telephone counseling may be useful, but there have been few direct tests of the impact of support. We describe a Telephone Motivational Interviewing (MI intervention targeting adherence to an Internet intervention for drivers with Type 1 Diabetes, DD.com, and compare completion of intervention benchmarks by those randomized to DD.com plus MI vs. DD.com only. The goal of the pre-intervention MI session was to increase the participant's motivation to complete the Internet intervention and all its assignments, while the goal of the post-treatment MI session was to plan for maintaining changes made during the intervention. Sessions were semi-structured and partially scripted to maximize consistency. MI Fidelity was coded using a standard coding system, the MITI. We examined the effects of MI support vs. no support on number of days from enrollment to program benchmarks. Results show that MI sessions were provided with good fidelity. Users who received MI support completed some program benchmarks such as Core 4 (t176 df = −2.25; p < .03 and 11 of 12 monthly driving diaries significantly sooner, but support did not significantly affect time to intervention completion (t177 df = −1.69; p < .10 or rates of completion. These data suggest that there is little benefit to therapist guidance for Internet interventions including automated email prompts and other automated minimal supports, but that a booster MI session may enhance collection of follow-up data.

VEHIL: a test facility for validation of fault management systems for advanced driver assistance systems

NARCIS (Netherlands)

Gietelink, O.J.; Ploeg, J.; Schutter, de B.; Verhaegen, M.H.

2004-01-01

We present a methodological approach for the validation of fault management systems for Advanced Driver Assistance Systems (ADAS). For the validation process the unique VEHIL facility, developed by TNO Automotive and currently situated in Helmond, The Netherlands, is applied. The VEHIL facility

Driver assistance systems - road to success for platooning; Fahrerassistenzsysteme - Wegbereiter fuer Lkw-Konvois

Energy Technology Data Exchange (ETDEWEB)

Happe, J.; Preuschoff, E. [Zentrum fuer Lern- und Wissensmanagement und Lehrstuhl Informatik im Maschinenbau der RWTH Aachen, Aachen (Germany)

2004-07-01

Resulting from the continuous increase of freight transport and the limitation of the capacity for road-transport, there is a need of optimising road traffic flow and of improving the utilisation of the given infrastructure. The objective is making the whole traffic system safer, more efficient and environmentally friendly. A potential concept is the realisation of truck platoons on highways by using advanced driver assistant systems (ADAS). The electronic coupling of the trucks in short distance minimises the work-load of the truck drivers and results in a safety benefit. Furthermore the short distances lead to a positive effect on road capacity and a reduction of the fuel consumption of the following vehicles because of lee-driving. Within a project ''Preparing action for the realisation of advanced driver assistant system in freight transport'' a group of scientists of the Aachen University worked on requirements for the medium-term realisation of automatic truck platoons on highways. (orig.)

Reliability prediction for the vehicles equipped with advanced driver assistance systems (ADAS and passive safety systems (PSS

Directory of Open Access Journals (Sweden)

Balbir S. Dhillon

2012-10-01

Full Text Available The human error has been reported as a major root cause in road accidents in today’s world. The human as a driver in road vehicles composed of human, mechanical and electrical components is constantly exposed to changing surroundings (e.g., road conditions, environmentwhich deteriorate the driver’s capacities leading to a potential accident. The auto industries and transportation authorities have realized that similar to other complex and safety sensitive transportation systems, the road vehicles need to rely on both advanced technologies (i.e., Advanced Driver Assistance Systems (ADAS and Passive Safety Systems (PSS (e.g.,, seatbelts, airbags in order to mitigate the risk of accidents and casualties. In this study, the advantages and disadvantages of ADAS as active safety systems as well as passive safety systems in road vehicles have been discussed. Also, this study proposes models that analyze the interactions between human as a driver and ADAS Warning and Crash Avoidance Systems and PSS in the design of vehicles. Thereafter, the mathematical models have been developed to make reliability prediction at any given time on the road transportation for vehicles equipped with ADAS and PSS. Finally, the implications of this study in the improvement of vehicle designs and prevention of casualties are discussed.

Development of device drivers embedded in real time OS for SPring-8 SR control system

International Nuclear Information System (INIS)

Masuda, T.; Fujiwara, S.; Nakamura, T.; Takebe, H.; Wada, T.

1994-01-01

A distributed computer system has been adopted for the SPring-8 SR control system. For lower level computers, we intend to adopt VMEbus computer systems with the real time OS which are compliant with POSIX. For R and D study, we introduced LynxOS and wrote device drivers for Digital Output(DO), Digital Input(DI) and Analog Input(AI) boards on VMEbus. They were successfully operated with device drivers. (author)

Integrated quality status and inventory tracking system for FFTF driver fuel pins

International Nuclear Information System (INIS)

Gottschalk, G.P.

1979-11-01

An integrated system for quality status and inventory tracking of Fast Flux Test Facility (FFTF) driver fuel pins has been developed. Automated fuel pin identification systems, a distributed computer network, and a data base are used to implement the tracking system

Conceptual Drivers for an Exploration Medical System

Science.gov (United States)

Antonsen, Erik; Hanson, Andrea; Shah, Ronak; Reed, Rebekah; Canga, Michael

2016-01-01

Interplanetary spaceflight, such as NASA's proposed three-year mission to Mars, provides unique and novel challenges when compared with human spaceflight to date. Extended distance and multi-year missions introduce new elements of operational complexity and additional risk. These elements include: inability to resupply medications and consumables, inability to evacuate injured or ill crew, uncharted psychosocial conditions, and communication delays that create a requirement for some level of autonomous medical capability. Because of these unique challenges, the approaches used in prior programs have limited application to a Mars mission. On a Mars mission, resource limitations will significantly constrain available medical capabilities, and require a paradigm shift in the approach to medical system design and risk mitigation for crew health. To respond to this need for a new paradigm, the Exploration Medical Capability (ExMC) Element is assessing each Mars mission phase-transit, surface stay, rendezvous, extravehicular activity, and return-to identify and prioritize medical needs for the journey beyond low Earth orbit (LEO). ExMC is addressing both planned medical operations, and unplanned contingency medical operations that meld clinical needs and research needs into a single system. This assessment is being used to derive a gap analysis and studies to support meaningful medical capabilities trades. These trades, in turn, allow the exploration medical system design to proceed from both a mission centric and ethics-based approach, and to manage the risks associated with the medical limitations inherent in an exploration class mission. This paper outlines the conceptual drivers used to derive medical system and vehicle needs from an integrated vision of how medical care will be provided within this paradigm. Keywords: (Max 6 keywords: exploration, medicine, spaceflight, Mars, research, NASA)

The High-efficiency LED Driver for Visible Light Communication Applications.

Science.gov (United States)

Gong, Cihun-Siyong Alex; Lee, Yu-Chen; Lai, Jyun-Liang; Yu, Chueh-Hao; Huang, Li Ren; Yang, Chia-Yen

2016-08-08

This paper presents a LED driver for VLC. The main purpose is to solve the low data rate problem used to be in switching type LED driver. The GaN power device is proposed to replace the traditional silicon power device of switching LED driver for the purpose of increasing switching frequency of converter, thereby increasing the bandwidth of data transmission. To achieve high efficiency, the diode-connected GaN power transistor is utilized to replace the traditional ultrafast recovery diode used to be in switching type LED driver. This work has been experimentally evaluated on 350-mA output current. The results demonstrate that it supports the data of PWM dimming level encoded in the PPM scheme for VLC application. The experimental results also show that system's efficiency of 80.8% can be achieved at 1-Mb/s data rate.

Systems analysis for modular versus multi-beam HIF drivers

International Nuclear Information System (INIS)

Meier, W.R.; Logan, B.G.

2004-01-01

Previous modeling for HIF drivers concentrated on designs in which 100 or more beams are grouped in an array and accelerated through a common set of induction cores. The total beam energy required by the target is achieved by the combination of final ion energy, current per beam and number of beams. Economic scaling favors a large number of small (∼1 cm dia.) beams. An alternative architecture has now been investigated, which we refer to as a modular driver. In this case, the driver is subdivided into many (>10) independent accelerators with one or many beams each. A key objective of the modular driver approach is to be able to demonstrate all aspects of the driver (source-to-target) by building a single, lower cost module compared to a full-scale, multi-beam driver. We consider and compare several design options for the modular driver including single-beam designs with solenoid instead of quadrupole magnets in order to transport the required current per module in a single beam, solenoid/quad combinations, and multi-beam, all-quad designs. The drivers are designed to meet the requirements of the hybrid target, which can accommodate a larger spot size than the distributed radiator target that was used for the Robust Point Design. We compare the multi-beam and modular driver configuration for a variety and assumptions and identify key technology advances needed for the modular design

Drivers` activities and information needs in an automated highway system. Working paper, August 1995-May 1996

Energy Technology Data Exchange (ETDEWEB)

Levitan, L.; Bloomfield, J.

1996-10-01

In most visions of the AHS--including that of the National Automated Highway System Consortium--it has been assumed that when a vehicle was under automated control, the driver would be allowed to engage in any of a variety of activities not related to driving (e.g, working, reading, sleeping). The objective of the first study reported here--one of the noncommuter studies--was to determine what drivers do when traveling under automated control, and whether the age of and/gender or the driver and/or the intrastring gap have an influence on those activities. One the objectives of the commuter experiment--of relevance for this report--was to determine whether what drivers do when traveling under automated control changes as a function of experience with the AHS (i.e., across trials). As conceptualization of the AHS proceeds, the details of the interface between the driver and the in-vehicle system will become more important. One part of that interface will be information supplied by the AHS to the driver, perhaps about such things as traffic conditions ahead predicted trip time to the driver`s selected exit, and so on. To maximize the utility of that information, it is important to determine what it is that drivers would like to know when traveling under automated control. The objective of the third study reported here--the second of the five noncommuter experiments--was to provide a first investigation of that issue.

A study of driver's route choice behavior based on evolutionary game theory.

Science.gov (United States)

Jiang, Xiaowei; Ji, Yanjie; Du, Muqing; Deng, Wei

2014-01-01

This paper proposes a route choice analytic method that embeds cumulative prospect theory in evolutionary game theory to analyze how the drivers adjust their route choice behaviors under the influence of the traffic information. A simulated network with two alternative routes and one variable message sign is built to illustrate the analytic method. We assume that the drivers in the transportation system are bounded rational, and the traffic information they receive is incomplete. An evolutionary game model is constructed to describe the evolutionary process of the drivers' route choice decision-making behaviors. Here we conclude that the traffic information plays an important role in the route choice behavior. The driver's route decision-making process develops towards different evolutionary stable states in accordance with different transportation situations. The analysis results also demonstrate that employing cumulative prospect theory and evolutionary game theory to study the driver's route choice behavior is effective. This analytic method provides an academic support and suggestion for the traffic guidance system, and may optimize the travel efficiency to a certain extent.

How countries link REDD+ interventions to drivers in their readiness plans: implications for monitoring systems

International Nuclear Information System (INIS)

Salvini, G; Herold, M; De Sy, V; Kissinger, G; Brockhaus, M; Skutsch, M

2014-01-01

Countries participating in the REDD+ scheme are in the readiness phase, designing policy interventions to address drivers of deforestation and forest degradation (DD). In order for REDD+ interventions to be effective, it is essential that they take into account the specific drivers that they aim to address. Moreover it is crucial to design systems that monitor the effectiveness of the planned interventions. In this article we provide a comprehensive and comparative assessment of interventions proposed by 43 REDD+ countries in 98 readiness documents. We summarize the types of interventions and assess if they are formulated referring to the drivers of DD that they are aiming to address. Based on this assessment we consider the implications for systems for monitoring effectiveness of proposed interventions. Most countries reviewed link proposed interventions to specific drivers of DD. The majority of the countries making this link have better driver data quality, in particularly those that present their data in ratio or ordinal terms. Proposed interventions focus not only on activities to reduce deforestation, but also on other forest related REDD+ activities such as sustainable forest management, which reduce forest degradation and enhance forest stocks. Moreover, driver-specific interventions often relate to drivers not only inside but also outside the forest sector. Hence we suggest that monitoring systems need to assess not only deforestation rates through remote sensing, but also degradation and other carbon stock changes within the forest, using more detailed ground level surveys and measurements. In addition, the performance of interventions outside the forest need to be monitored, even if the impacts of these cannot be linked to specific changes in forest carbon stock in specific locations. (paper)

Assisting Driver Sovereignty : A Fail-Safe Design Approach to Driver Distraction

NARCIS (Netherlands)

Van Gijssel, A.

2013-01-01

This thesis investigates the potential of a fail-safe approach to driver distraction through novel interface concepts for integrated Advanced Driver Assistance Systems (ADAS). Traffic accidents are a negative side effect of the universal and economical desire for mobility. The year 2009 saw the

Vehicle emission implications of drivers' smart advisory system for traffic operations in work zones.

Science.gov (United States)

Li, Qing; Qiao, Fengxiang; Yu, Lei

2016-05-01

Wireless communication systems have been broadly applied in various complicated traffic operations to improve mobility and safety on roads, which may raise a concern about the implication of the new technology on vehicle emissions. This paper explores how the wireless communication systems improve drivers' driving behaviors and its contributions to the emission reduction, in terms of Operating Mode (OpMode) IDs distribution used in emission estimation. A simulated work zone with completed traffic operation was selected as a test bed. Sixty subjects were recruited for the tests, whose demographic distribution was based on the Census data in Houston, Texas. A scene of a pedestrian's crossing in the work zone was designed for the driving test. Meanwhile, a wireless communication system called Drivers Smart Advisory System (DSAS) was proposed and introduced in the driving simulation, which provided drivers with warning messages in the work zone. Two scenarios were designed for a leading vehicle as well as for a following vehicle driving through the work zone, which included a base test without any wireless communication systems, and a driving test with the trigger of the DSAS. Subjects' driving behaviors in the simulation were recorded to evaluate safety and estimate the vehicle emission using the Environmental Protection Agency (EPA) released emission model MOVES. The correlation between drivers' driving behavior and the distribution of the OpMode ID during each scenario was investigated. Results show that the DSAS was able to induce drivers to accelerate smoothly, keep longer headway distance and stop earlier for a hazardous situation in the work zone, which driving behaviors result in statistically significant reduction in vehicle emissions for almost all studied air pollutants (p-values range from 4.10E-51 to 2.18E-03). The emission reduction was achieved by the switching the distribution of the OpMode IDs from higher emission zones to lower emission zones

Generic Model Predictive Control Framework for Advanced Driver Assistance Systems

NARCIS (Netherlands)

Wang, M.

2014-01-01

This thesis deals with a model predictive control framework for control design of Advanced Driver Assistance Systems, where car-following tasks are under control. The framework is applied to design several autonomous and cooperative controllers and to examine the controller properties at the

Autonomous emergency braking systems adapted to snowy road conditions improve drivers' perceived safety and trust.

Science.gov (United States)

Koglbauer, Ioana; Holzinger, Jürgen; Eichberger, Arno; Lex, Cornelia

2018-04-03

This study investigated drivers' evaluation of a conventional autonomous emergency braking (AEB) system on high and reduced tire-road friction and compared these results to those of an AEB system adaptive to the reduced tire-road friction by earlier braking. Current automated systems such as the AEB do not adapt the vehicle control strategy to the road friction; for example, on snowy roads. Because winter precipitation is associated with a 19% increase in traffic crashes and a 13% increase in injuries compared to dry conditions, the potential of conventional AEB to prevent collisions could be significantly improved by including friction in the control algorithm. Whereas adaption is not legally required for a conventional AEB system, higher automated functions will have to adapt to the current tire-road friction because human drivers will not be required to monitor the driving environment at all times. For automated driving functions to be used, high levels of perceived safety and trust of occupants have to be reached with new systems. The application case of an AEB is used to investigate drivers' evaluation depending on the road condition in order to gain knowledge for the design of future driving functions. In a driving simulator, the conventional, nonadaptive AEB was evaluated on dry roads with high friction (μ = 1) and on snowy roads with reduced friction (μ = 0.3). In addition, an AEB system adapted to road friction was designed for this study and compared with the conventional AEB on snowy roads with reduced friction. Ninety-six drivers (48 males, 48 females) assigned to 5 age groups (20-29, 30-39, 40-49, 50-59, and 60-75 years) drove with AEB in the simulator. The drivers observed and evaluated the AEB's braking actions in response to an imminent rear-end collision at an intersection. The results show that drivers' safety and trust in the conventional AEB were significantly lower on snowy roads, and the nonadaptive autonomous braking strategy was

Active gated imaging in driver assistance system

Science.gov (United States)

Grauer, Yoav

2014-04-01

In this paper, we shall present the active gated imaging system (AGIS) in relation to the automotive field. AGIS is based on a fast-gated camera and pulsed illuminator, synchronized in the time domain to record images of a certain range of interest. A dedicated gated CMOS imager sensor and near infra-red (NIR) pulsed laser illuminator, is presented in this paper to provide active gated technology. In recent years, we have developed these key components and learned the system parameters, which are most beneficial to nighttime (in all weather conditions) driving in terms of field of view, illumination profile, resolution, and processing power. We shall present our approach of a camera-based advanced driver assistance systems (ADAS) named BrightEye™, which makes use of the AGIS technology in the automotive field.

Do management practices support or constrain safe driving behaviour? A multi-level investigation in a sample of occupational drivers.

Science.gov (United States)

Newnam, Sharon; Warmerdam, Amanda; Sheppard, Dianne; Griffin, Mark; Stevenson, Mark

2017-05-01

It has been estimated that one-third of all work-related deaths occur while driving for work-related purposes. Despite this, many organisations are unaware of the practices, beyond those that identify and control the impact of unforeseen events (i.e., risk management), that predispose drivers to risk. This study addresses the issue by identifying the management practices operationalised as, High Performance Workplace Systems (HPWS) that influence safe driver behaviour. The study also explores the value given to safety by senior level management as a moderator of the relationship between HPWS practices and driver behaviour. Each factor was tested within a two level hierarchical model consisting of 911 drivers, nested within 161 supervisors and 83 organisations. The findings highight that under conditions of high investment in job and work design, communication and selection practices, drivers reported poorer driving behaviour. An interaction effect also demonstrated that under conditions of high investment in remuneration, drivers reported safer behaviour, but only when they perceived that managers valued and prioritised safety. The findings challenge current thinking in the management of workplace road safety. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Method to Increase Drivers' Trust in Collision Warning Systems Based on Reliability Information of Sensor

Science.gov (United States)

Tsutsumi, Shigeyoshi; Wada, Takahiro; Akita, Tokihiko; Doi, Shun'ichi

Driver's workload tends to be increased during driving under complicated traffic environments like a lane change. In such cases, rear collision warning is effective for reduction of cognitive workload. On the other hand, it is pointed out that false alarm or missing alarm caused by sensor errors leads to decrease of driver' s trust in the warning system and it can result in low efficiency of the system. Suppose that reliability information of the sensor is provided in real-time. In this paper, we propose a new warning method to increase driver' s trust in the system even with low sensor reliability utilizing the sensor reliability information. The effectiveness of the warning methods is shown by driving simulator experiments.

An innovative non-intrusive driver assistance system for vital signal monitoring.

NARCIS (Netherlands)

Sun, Y. & Yu, X.

2016-01-01

This paper describes an in-vehicle nonintrusive biopotential measurement system for driver health monitoring and fatigue detection. Previous research has found that the physiological signals including eye features, electrocardiography (ECG), electroencephalography (EEG) and their secondary

Letting in-vehicle navigation lead the way: Older drivers' perceptions of and ability to follow a GPS navigation system.

Science.gov (United States)

Stinchcombe, Arne; Gagnon, Sylvain; Kateb, Matthew; Curtis, Meredith; Porter, Michelle M; Polgar, Jan; Bédard, Michel

2017-09-01

In-vehicle navigation systems have the potential to simplify the driving task by reducing the drivers' need to engage in wayfinding, especially in unfamiliar environments. This study sought to characterize older drivers' overall assessment of using in-vehicle GPS technology as part of a research study and to explore whether the use of this technology has an impact on participants' driving behaviour. Forty-seven older drivers completed an on-road evaluation where directions were provided by an in-vehicle GPS navigation system and their behaviour was recorded using video technology. They later completed a questionnaire to assess their perception of the navigation system. After the study, participants were grouped based on whether they were able to accurately follow the instructions provided by the navigation system. The results indicated that most drivers were satisfied with the navigation technology and found the directions it provided to be clear. There were no statistically significant differences in the number of on-road errors committed by drivers who did not follow the directions from the navigation system in comparison to drivers who did follow the directions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Experimental Research in Boost Driver with EDLCs

Science.gov (United States)

Matsumoto, Hirokazu

The supply used in servo systems tends to have a high voltage in order to reduce loss and improve the response of motor drives. We propose a new boost motor driver that comprises EDLCs. The proposed driver has a simple structure, wherein the EDLCs are connected in series to the supply, and comprises a charge circuit to charge the EDLCs. The proposed driver has three advantages over conventional boost drivers. The first advantage is that the driver can easily attain the stable boost voltage. The second advantage is that the driver can reduce input power peaks. In a servo system, the input power peaks become greater than the rated power in order to accelerate the motor rapidly. This implies that the equipments that supply power to servo systems must have sufficient power capacity to satisfy the power peaks. The proposed driver can suppress the increase of the power capacity of supply facilities. The third advantage is that the driver can store almost all of the regenerative energy. Conventional drivers have a braking resistor to suppress the increase in the DC link voltage. This causes a considerable reduction in the efficiency. The proposed driver is more efficient than conventional drivers. In this study, the experimental results confirmed the effectiveness of the proposed driver and showed that the drive performance of the proposed driver is the same as that of a conventional driver. Furthermore, it was confirmed that the results of the simulation of a model of the EDLC module, whose capacitance is dependent on the frequency, correspond well with the experimental results.

A Two-Dimensional Weighting Function for a Driver Assistance System

NARCIS (Netherlands)

De Winter, J.; Mulder, M.; Van Paassen, M.M.; Abbink, D.A.; Wieringa, P.A.

2008-01-01

Driver assistance systems that supply force feedback (FF) on the accelerator commonly use relative distance and velocity with respect to the closest lead vehicle in front of the own vehicle. This 1-D feedback might not accurately represent the situation and can cause unwanted step-shaped changes in

A Framework for Function Allocation in Intelligent Driver Interface Design for Comfort and Safety

Directory of Open Access Journals (Sweden)

Wuhong Wang

2010-11-01

Full Text Available This paper presents a conceptual framework for ecological function allocation and optimization matching solution for a human-machine interface with intelligent characteristics by lwho does what and when and howr consideration. As a highlighted example in nature-social system, intelligent transportation system has been playing increasingly role in keeping traffic safety, our research is concerned with identifying human factors problem of In-vehicle Support Systems (ISSs and revealing the consequence of the effects of ISSs on driver cognitive interface. The primary objective is to explore some new ergonomics principals that will be able to use to design an intelligent driver interface for comfort and safety, which will address the impact of driver interfaces layouts, traffic information types, and driving behavioral factors on the advanced vehicles safety design.

USING THE SAFE SYSTEM APPROACH TO KEEP OLDER DRIVERS SAFELY MOBILE

Directory of Open Access Journals (Sweden)

Jim LANGFORD

2006-01-01

Full Text Available In 2003, Australian road transport jurisdictions collectively accepted that the greatest road safety gains would be achieved through adopting a Safe System approach, derived from Sweden's Vision Zero and the Netherlands' Sustainable Safety strategies. A key objective of all three approaches is to manage vehicles, the road infrastructure, speeds, road users and the interactions between these components, to ensure that in the event of crashes, crash energies will remain at levels that minimize the probability of death and serious injury. Older drivers pose a particular challenge to the Safe System approach, given particularly their greater physical frailty, their driving patterns and for some at least, their reduced fitness to drive. This paper has analyzed the so-called ‘older driver problem’ and identified a number of key factors underpinning their crash levels, for which countermeasures can be identified and implemented within a Safe System framework. The recommended countermeasures consist of: (1 safer roads, through a series of design improvements particularly governing urban intersections; (2 safer vehicles, through both the promotion of crashworthiness as a critical consideration when purchasing a vehicle and the wide use of developed and developing ITS technologies; (3 safer speeds especially at intersections; and (4 safer road users, through both improved assessment procedures to identify the minority of older drivers with reduced fitness to drive and educational efforts to encourage safer driving habits particularly but not only through self-regulation.

Preface to the special section on human factors and automation in vehicles: designing highly automated vehicles with the driver in mind.

Science.gov (United States)

Merat, Natasha; Lee, John D

2012-10-01

This special section brings together diverse research regarding driver interaction with advanced automotive technology to guide design of increasingly automated vehicles. Rapidly evolving vehicle automation will likely change cars and trucks more in the next 5 years than the preceding 50, radically redefining what it means to drive. This special section includes 10 articles from European and North American researchers reporting simulator and naturalistic driving studies. Little research has considered the consequences of fully automated driving, with most focusing on lane-keeping and speed control systems individually. The studies reveal two underlying design philosophies: automate driving versus support driving. Results of several studies, consistent with previous research in other domains, suggest that the automate philosophy can delay driver responses to incidents in which the driver has to intervene and take control from the automation. Understanding how to orchestrate the transfer or sharing of control between the system and the driver, particularly in critical incidents, emerges as a central challenge. Designers should not assume that automation can substitute seamlessly for a human driver, nor can they assume that the driver can safely accommodate the limitations of automation. Designers, policy makers, and researchers must give careful consideration to what role the person should have in highly automated vehicles and how to support the driver if the driver is to be responsible for vehicle control. As in other domains, driving safety increasingly depends on the combined performance of the human and automation, and successful designs will depend on recognizing and supporting the new roles of the driver.

Adaptive importance sampling for probabilistic validation of advanced driver assistance systems

NARCIS (Netherlands)

Gietelink, O.J.; Schutter, B. de; Verhaegen, M.

2006-01-01

We present an approach for validation of advanced driver assistance systems, based on randomized algorithms. The new method consists of an iterative randomized simulation using adaptive importance sampling. The randomized algorithm is more efficient than conventional simulation techniques. The

A Driver Behavior Learning Framework for Enhancing Traffic Simulation

Directory of Open Access Journals (Sweden)

Ramona Maria Paven

2014-06-01

Full Text Available Traffic simulation provides an essential support for developing intelligent transportation systems. It allows affordable validation of such systems using a large variety of scenarios that involves massive data input. However, realistic traffic models are hard to be implemented especially for microscopic traffic simulation. One of the hardest problems in this context is to model the behavior of drivers, due the complexity of human nature. The work presented in this paper proposes a framework for learning driver behavior based on a Hidden Markov Model technique. Moreover, we propose also a practical method to inject this behavior in a traffic model used by the SUMO traffic simulator. To demonstrate the effectiveness of this method we present a case study involving real traffic collected from Timisoara city area.

Model implementation for dynamic computation of system cost for advanced life support

Science.gov (United States)

Levri, J. A.; Vaccari, D. A.

2004-01-01

Life support system designs for long-duration space missions have a multitude of requirements drivers, such as mission objectives, political considerations, cost, crew wellness, inherent mission attributes, as well as many other influences. Evaluation of requirements satisfaction can be difficult, particularly at an early stage of mission design. Because launch cost is a critical factor and relatively easy to quantify, it is a point of focus in early mission design. The method used to determine launch cost influences the accuracy of the estimate. This paper discusses the appropriateness of dynamic mission simulation in estimating the launch cost of a life support system. This paper also provides an abbreviated example of a dynamic simulation life support model and possible ways in which such a model might be utilized for design improvement. c2004 COSPAR. Published by Elsevier Ltd. All rights reserved.

Environmental control and life support system requirements and technology needs for advanced manned space missions

Science.gov (United States)

Powell, Ferolyn T.; Sedej, Melaine; Lin, Chin

1987-01-01

NASA has completed an environmental control and life support system (ECLSS) technology R&D plan for advanced missions which gave attention to the drivers (crew size, mission duration, etc.) of a range of manned missions under consideration. Key planning guidelines encompassed a time horizon greater than 50 years, funding resource requirements, an evolutionary approach to goal definition, and the funding of more than one approach to satisfy a given perceived requirement. Attention was given to the ECLSS requirements of transportation and service vehicles, platforms, bases and settlements, ECLSS functions and average load requirements, unique drivers for various missions, and potentially exploitable commonalities among vehicles and habitats.

Smart EV Energy Management System to Support Grid Services

Science.gov (United States)

Wang, Bin

Under smart grid scenarios, the advanced sensing and metering technologies have been applied to the legacy power grid to improve the system observability and the real-time situational awareness. Meanwhile, there is increasing amount of distributed energy resources (DERs), such as renewable generations, electric vehicles (EVs) and battery energy storage system (BESS), etc., being integrated into the power system. However, the integration of EVs, which can be modeled as controllable mobile energy devices, brings both challenges and opportunities to the grid planning and energy management, due to the intermittency of renewable generation, uncertainties of EV driver behaviors, etc. This dissertation aims to solve the real-time EV energy management problem in order to improve the overall grid efficiency, reliability and economics, using online and predictive optimization strategies. Most of the previous research on EV energy management strategies and algorithms are based on simplified models with unrealistic assumptions that the EV charging behaviors are perfectly known or following known distributions, such as the arriving time, leaving time and energy consumption values, etc. These approaches fail to obtain the optimal solutions in real-time because of the system uncertainties. Moreover, there is lack of data-driven strategy that performs online and predictive scheduling for EV charging behaviors under microgrid scenarios. Therefore, we develop an online predictive EV scheduling framework, considering uncertainties of renewable generation, building load and EV driver behaviors, etc., based on real-world data. A kernel-based estimator is developed to predict the charging session parameters in real-time with improved estimation accuracy. The efficacy of various optimization strategies that are supported by this framework, including valley-filling, cost reduction, event-based control, etc., has been demonstrated. In addition, the existing simulation-based approaches do

The bottom-supported fast reactor - system simplifications and enhanced safety

International Nuclear Information System (INIS)

Petrozelli, J.; Golan, S.; Kawamura, Yutaka; Kumaoka, Yoshio; Nakagawa, Hiroshi

1992-01-01

The 600-MW(electric) bottom-supported fast reactor (BSFR) incorporates the following key features: (1) modular upper internal structure (UIS); (2) electromagnetic pumps (EMPs); (3) low-sodium-void-worth metal-fuel core; and (4) bottom supported reactor vessel (BSRV), which is entirely supported by the basement, except for the control rods, control rod drives (CRDs), UIS, and the stationary plug; by comparison, a top-supported reactor vessel (TSRV) is completely supported by the operating floor. The diameter of the reactor vessel (RV) is 12.8 m (42 ft), and the height (distance from the basemat to the operating floor) is 19.8 m (65 ft). The RV is supported by a single support cylinder anchored to the basemat. The core has 210 driver assemblies and 192 radial blanket assemblies in an annular configuration. The primary heat transport system components consist of four intermediate heat exchangers (IHXs), four EMPs, and four primary reactor auxillary cooling systems. All these components are supported by the BSRV and hang from their tops. Six modular, vertically movable UIS mechanisms clear the UIS from the space over the core during refueling. The top closure is designed to operate at the reactor outlet temperature and is free to expand and contract. Small bellows between the top closure and each UIS model accommodate differential movements and comprise a portion of the cover gas boundary. A 1200-MW(electric) plant with two 600-MW(electric) (twin) nuclear steam supply systems is being studied

Analyzing the Drivers of Advanced Sustainable Manufacturing System Using AHP Approach

Directory of Open Access Journals (Sweden)

K. Madan Shankar

2016-08-01

Full Text Available A number of current manufacturing sectors are striving hard to introduce innovative long-term strategies into their operations. As a result, many scholarly studies have found it fruitful to investigate advanced manufacturing strategies such as agile, computer-integrated, and cellular manufacturing. Through the example of downstream cases, manufacturing sectors have learned that financial benefits garnered through automated technologies cannot be counted on as a sole measure to ensure their success in today’s competitive and fluctuating marketplaces. The objective of this study is to integrate those advanced techniques with sustainable operations, to promote advanced sustainable manufacturing so those manufacturing sectors can thrive even in uncertain markets. To establish this connection, this study analyzes the drivers of advanced sustainable manufacturing through a proposed framework validated through a case study in India. Common drivers are collected from the literature, calibrated with opinions from experts, and analyzed through an analytical hierarchy process (AHP, which is a multi-criteria decision making (MCDM approach. This study reveals that quality is the primary driver that pressures manufacturing sectors to adopt advanced sustainable manufacturing. Manufacturers can easily note the top ranked driver and adopt it to soundly implement advanced sustainable manufacturing. In addition, some key future scopes are explored along with possible recommendations for effective implementation of advanced sustainable manufacturing systems.

Current trends in laser fusion driver and beam combination laser system using stimulated Brillouin scattering phase conjugate mirrors for a fusion driver

International Nuclear Information System (INIS)

Kong, Hong Jin

2008-01-01

Laser fusion energy (LFE) is well known as one of the promising sources if clean energy for mankind. Laser fusion researches have been actively progressed, since Japan and the Soviet Union as well as USA developed ultrahigh power lasers at the beginning of 1970s. At present in USA, NIF (National Ignition Facility), which is the largest laser fusion facility in the world, is under construction and will be completed in 2008. Japan as a leader of the laser fusion research has developed a high energy and high power laser system, Gekko XII, and is under contemplation of FIREX projects for the fast ignition. China also has SG I, II lasers for performing the fusion research, and SG III is under construction as a next step. France is also constructing LMJ (Laser countries, many other developed countries in Europe, such as Russia, Germany, UK, and so on, have their own high energy laser systems for the fusion research. In Korea, the high power laser development started with SinMyung laser in KAIST in 1994, and KLF (KAERI Laser Facility) of KAERI was recently completed in 2007. For the practical use of laser fusion energy, the laser driver should be operated with a high repetition rate around 10Hz. Yet, current high energy laser systems, Such as NIF, Gekko XII, and etc., can be operated with only several shots per day. Some researchers have developed their own techniques to reduce the thermal loads of the laser material, by using laser diodes as pump sources and ceramic laser materials with high thermal energy scaling up for the real fusion driver. For this reason, H. J. Kong et al. proposed the beam combination laser system using stimulated Brillouin scattering phase conjugate mirrors (SBS PCMs) for a fusion driver. Proposed beam combination has many advantages for energy scaling up; it is composed by simple optical systems with small amount of components, there is no interaction between neighbored sub beams, the SBS PCMs can be used for a high energy beam reflection with

Component framework support for developing device drivers

OpenAIRE

Michiels, Sam; Kenens, Peter; Matthijs, Frank; Walravens, Dirk; Berbers, Yolande; Verbaeten, Pierre

2000-01-01

In this paper, we advocate the use of component framework technology for developing state-of-the-art system software. Relevant contributions of DiPS (Distrinet Protocol Stack), a component framework, include its anonymous interaction model, connectors for handling non-functional issues such as the concurrency model, and builder support. DiPS has effectively been used in industrial protocol stacks. This paper shows how we are using the DiPS component framework to build and support flexib...

Visual behaviour analysis and driver cognitive model

Energy Technology Data Exchange (ETDEWEB)

Baujon, J.; Basset, M.; Gissinger, G.L. [Mulhouse Univ., (France). MIPS/MIAM Lab.

2001-07-01

Recent studies on driver behaviour have shown that perception - mainly visual but also proprioceptive perception - plays a key role in the ''driver-vehicle-road'' system and so considerably affects the driver's decision making. Within the framework of the behaviour analysis and studies low-cost system (BASIL), this paper presents a correlative, qualitative and quantitative study, comparing the information given by visual perception and by the trajectory followed. This information will help to obtain a cognitive model of the Rasmussen type according to different driver classes. Many experiments in real driving situations have been carried out for different driver classes and for a given trajectory profile, using a test vehicle and innovative, specially designed, real-time tools, such as the vision system or the positioning module. (orig.)

Proving autonomous vehicle and advanced driver assistance systems safety : final research report.

Science.gov (United States)

2016-02-15

The main objective of this project was to provide technology for answering : crucial safety and correctness questions about verification of autonomous : vehicle and advanced driver assistance systems based on logic. : In synergistic activities, we ha...

Creating the environment for driver distraction: A thematic framework of sociotechnical factors.

Science.gov (United States)

Parnell, Katie J; Stanton, Neville A; Plant, Katherine L

2018-04-01

As modern society becomes more reliant on technology, its use within the vehicle is becoming a concern for road safety due to both portable and built-in devices offering sources of distraction. While the effects of distracting technologies are well documented, little is known about the causal factors that lead to the drivers' engagement with technological devices. The relevance of the sociotechnical system within which the behaviour occurs requires further research. This paper presents two experiments, the first aims to assess the drivers self-reported decision to engage with technological tasks while driving and their reasoning for doing so with respect to the wider sociotechnical system. This utilised a semi-structured interview method, conducted with 30 drivers to initiate a discussion on their likelihood of engaging with 22 different tasks across 7 different road types. Inductive thematic analysis provided a hierarchical thematic framework that detailed the self-reported causal factors that influence the drivers' use of technology whilst driving. The second experiment assessed the relevance of the hierarchical framework to a model of distraction that was established from within the literature on the drivers use of distracting technologies while driving. The findings provide validation for some relationships studied in the literature, as well as providing insights into relationships that require further study. The role of the sociotechnical system in the engagement of distractions while driving is highlighted, with the causal factors reported by drivers suggesting the importance of considering the wider system within which the behaviour is occurring and how it may be creating the conditions for distraction to occur. This supports previous claims made within the literature based model. Recommendations are proposed that encourage a movement away from individual focused countermeasures towards systemic actors. Copyright © 2017 Elsevier Ltd. All rights reserved.

Decadal-Scale Forecasting of Climate Drivers for Marine Applications.

Science.gov (United States)

Salinger, J; Hobday, A J; Matear, R J; O'Kane, T J; Risbey, J S; Dunstan, P; Eveson, J P; Fulton, E A; Feng, M; Plagányi, É E; Poloczanska, E S; Marshall, A G; Thompson, P A

Climate influences marine ecosystems on a range of time scales, from weather-scale (days) through to climate-scale (hundreds of years). Understanding of interannual to decadal climate variability and impacts on marine industries has received less attention. Predictability up to 10 years ahead may come from large-scale climate modes in the ocean that can persist over these time scales. In Australia the key drivers of climate variability affecting the marine environment are the Southern Annular Mode, the Indian Ocean Dipole, the El Niño/Southern Oscillation, and the Interdecadal Pacific Oscillation, each has phases that are associated with different ocean circulation patterns and regional environmental variables. The roles of these drivers are illustrated with three case studies of extreme events-a marine heatwave in Western Australia, a coral bleaching of the Great Barrier Reef, and flooding in Queensland. Statistical and dynamical approaches are described to generate forecasts of climate drivers that can subsequently be translated to useful information for marine end users making decisions at these time scales. Considerable investment is still needed to support decadal forecasting including improvement of ocean-atmosphere models, enhancement of observing systems on all scales to support initiation of forecasting models, collection of important biological data, and integration of forecasts into decision support tools. Collaboration between forecast developers and marine resource sectors-fisheries, aquaculture, tourism, biodiversity management, infrastructure-is needed to support forecast-based tactical and strategic decisions that reduce environmental risk over annual to decadal time scales. © 2016 Elsevier Ltd. All rights reserved.

Driver's anger state identification by using facial expression in ...

African Journals Online (AJOL)

Preventive safety system of vehicle is highlighted to reduce the number of traffic accidents. Driver's state adaptive driving safety system may be one of candidates of the safety system. Identifying driver's psychosomatic states is indispensable to establish those safety systems. Anger of driver state is often seen in traffic ...

Knowledge bases, clinical decision support systems, and rapid learning in oncology.

Science.gov (United States)

Yu, Peter Paul

2015-03-01

One of the most important benefits of health information technology is to assist the cognitive process of the human mind in the face of vast amounts of health data, limited time for decision making, and the complexity of the patient with cancer. Clinical decision support tools are frequently cited as a technologic solution to this problem, but to date useful clinical decision support systems (CDSS) have been limited in utility and implementation. This article describes three unique sources of health data that underlie fundamentally different types of knowledge bases which feed into CDSS. CDSS themselves comprise a variety of models which are discussed. The relationship of knowledge bases and CDSS to rapid learning health systems design is critical as CDSS are essential drivers of rapid learning in clinical care. Copyright © 2015 by American Society of Clinical Oncology.

Probabilistic safety analysis about the radiation risk for the driver in a fast-scan container/vehicle inspection system

International Nuclear Information System (INIS)

Li Junli; Zhu Guoping; Ming Shenjin; Cao Yanfeng

2008-01-01

A new Container/Vehicle Inspection System called fast-scan inspection system has been developed and used in some countries, which has a special advantage in scanning efficiency of 200 - 400 containers per hour. However, for its unique scanning mode, the fast-scan inspection system causes some worries about the radiation risk for the truck drivers, who will drive the container truck to pass through the scanning tunnel and might be exposed by the radiation beam in accidents. A PSA analysis, which has been widely used to evaluate the safety of nuclear power plant in the past, is presented here to estimate the probability of accidental exposure to the driver and evaluate the health risk. The fault tree and event tree analysis show that the probability of accidental exposure to the driver is pretty low and the main failure contributions are human errors and scanning control devices failures, which provides some recommendations for the further improvement about this product. Furthermore, on the basic of ICRP No.60 and 76 reports, the health risk to the truck driver is only about 4.0x10 -14 /a. Compared with the exempt level of 5x10 -7 /a, it can be concluded that the fast-scan system is safe enough for the truck driver. (author)

Improving driver alertness through music selection using a mobile EEG to detect brainwaves.

Science.gov (United States)

Liu, Ning-Han; Chiang, Cheng-Yu; Hsu, Hsiang-Ming

2013-06-26

Driving safety has become a global topic of discussion with the recent development of the Smart Car concept. Many of the current car safety monitoring systems are based on image discrimination techniques, such as sensing the vehicle drifting from the main road, or changes in the driver's facial expressions. However, these techniques are either too simplistic or have a low success rate as image processing is easily affected by external factors, such as weather and illumination. We developed a drowsiness detection mechanism based on an electroencephalogram (EEG) reading collected from the driver with an off-the-shelf mobile sensor. This sensor employs wireless transmission technology and is suitable for wear by the driver of a vehicle. The following classification techniques were incorporated: Artificial Neural Networks, Support Vector Machine, and k Nearest Neighbor. These classifiers were integrated with integration functions after a genetic algorithm was first used to adjust the weighting for each classifier in the integration function. In addition, since past studies have shown effects of music on a person's state-of-mind, we propose a personalized music recommendation mechanism as a part of our system. Through the in-car stereo system, this music recommendation mechanism can help prevent a driver from becoming drowsy due to monotonous road conditions. Experimental results demonstrate the effectiveness of our proposed drowsiness detection method to determine a driver's state of mind, and the music recommendation system is therefore able to reduce drowsiness.

Toward best practice in Human Machine Interface design for older drivers: A review of current design guidelines.

Science.gov (United States)

Young, K L; Koppel, S; Charlton, J L

2017-09-01

Older adults are the fastest growing segment of the driving population. While there is a strong emphasis for older people to maintain their mobility, the safety of older drivers is a serious community concern. Frailty and declines in a range of age-related sensory, cognitive, and physical impairments can place older drivers at an increased risk of crash-related injuries and death. A number of studies have indicated that in-vehicle technologies such as Advanced Driver Assistance Systems (ADAS) and In-Vehicle Information Systems (IVIS) may provide assistance to older drivers. However, these technologies will only benefit older drivers if their design is congruent with the complex needs and diverse abilities of this driving cohort. The design of ADAS and IVIS is largely informed by automotive Human Machine Interface (HMI) guidelines. However, it is unclear to what extent the declining sensory, cognitive and physical capabilities of older drivers are addressed in the current guidelines. This paper provides a review of key current design guidelines for IVIS and ADAS with respect to the extent they address age-related changes in functional capacities. The review revealed that most of the HMI guidelines do not address design issues related to older driver impairments. In fact, in many guidelines driver age and sensory cognitive and physical impairments are not mentioned at all and where reference is made, it is typically very broad. Prescriptive advice on how to actually design a system so that it addresses the needs and limitations of older drivers is not provided. In order for older drivers to reap the full benefits that in-vehicle technology can afford, it is critical that further work establish how older driver limitations and capabilities can be supported by the system design process, including their inclusion into HMI design guidelines. Copyright © 2016 Elsevier Ltd. All rights reserved.

Ventilation and Heart Rate Monitoring in Drivers using a Contactless Electrical Bioimpedance System

Science.gov (United States)

Macías, R.; García, M. A.; Ramos, J.; Bragós, R.; Fernández, M.

2013-04-01

Nowadays, the road safety is one of the most important priorities in the automotive industry. Many times, this safety is jeopardized because of driving under inappropriate states, e.g. drowsiness, drugs and/or alcohol. Therefore several systems for monitoring the behavior of subjects during driving are researched. In this paper, a device based on a contactless electrical bioimpedance system is shown. Using the four-wire technique, this system is capable of obtaining the heart rate and the ventilation of the driver through multiple textile electrodes. These textile electrodes are placed on the car seat and the steering wheel. Moreover, it is also reported several measurements done in a controlled environment, i.e. a test room where there are no artifacts due to the car vibrations or the road state. In the mentioned measurements, the system response can be observed depending on several parameters such as the placement of the electrodes or the number of clothing layers worn by the driver.

Ventilation and Heart Rate Monitoring in Drivers using a Contactless Electrical Bioimpedance System

International Nuclear Information System (INIS)

Macías, R; García, M A; Ramos, J; Bragós, R; Fernández, M

2013-01-01

Nowadays, the road safety is one of the most important priorities in the automotive industry. Many times, this safety is jeopardized because of driving under inappropriate states, e.g. drowsiness, drugs and/or alcohol. Therefore several systems for monitoring the behavior of subjects during driving are researched. In this paper, a device based on a contactless electrical bioimpedance system is shown. Using the four-wire technique, this system is capable of obtaining the heart rate and the ventilation of the driver through multiple textile electrodes. These textile electrodes are placed on the car seat and the steering wheel. Moreover, it is also reported several measurements done in a controlled environment, i.e. a test room where there are no artifacts due to the car vibrations or the road state. In the mentioned measurements, the system response can be observed depending on several parameters such as the placement of the electrodes or the number of clothing layers worn by the driver.

Agriculture production as a major driver of the Earth system exceeding planetary boundaries

Directory of Open Access Journals (Sweden)

Bruce M. Campbell

2017-12-01

Full Text Available We explore the role of agriculture in destabilizing the Earth system at the planetary scale, through examining nine planetary boundaries, or "safe limits": land-system change, freshwater use, biogeochemical flows, biosphere integrity, climate change, ocean acidification, stratospheric ozone depletion, atmospheric aerosol loading, and introduction of novel entities. Two planetary boundaries have been fully transgressed, i.e., are at high risk, biosphere integrity and biogeochemical flows, and agriculture has been the major driver of the transgression. Three are in a zone of uncertainty i.e., at increasing risk, with agriculture the major driver of two of those, land-system change and freshwater use, and a significant contributor to the third, climate change. Agriculture is also a significant or major contributor to change for many of those planetary boundaries still in the safe zone. To reduce the role of agriculture in transgressing planetary boundaries, many interventions will be needed, including those in broader food systems.

Is More Better? - Night Vision Enhancement System's Pedestrian Warning Modes and Older Drivers.

Science.gov (United States)

Brown, Timothy; He, Yefei; Roe, Cheryl; Schnell, Thomas

2010-01-01

Pedestrian fatalities as a result of vehicle collisions are much more likely to happen at night than during day time. Poor visibility due to darkness is believed to be one of the causes for the higher vehicle collision rate at night. Existing studies have shown that night vision enhancement systems (NVES) may improve recognition distance, but may increase drivers' workload. The use of automatic warnings (AW) may help minimize workload, improve performance, and increase safety. In this study, we used a driving simulator to examine performance differences of a NVES with six different configurations of warning cues, including: visual, auditory, tactile, auditory and visual, tactile and visual, and no warning. Older drivers between the ages of 65 and 74 participated in the study. An analysis based on the distance to pedestrian threat at the onset of braking response revealed that tactile and auditory warnings performed the best, while visual warnings performed the worst. When tactile or auditory warnings were presented in combination with visual warning, their effectiveness decreased. This result demonstrated that, contrary to general sense regarding warning systems, multi-modal warnings involving visual cues degraded the effectiveness of NVES for older drivers.

U.S. DOE driver development for ICF

International Nuclear Information System (INIS)

Sluyter, M.M.

1995-01-01

The goal of the Department of Energy (DOE) supported Inertial Confinement Fusion (ICF) Program is to produce pure fusion ignition with fusion yields of 200 to 1000 millions of joules, which could find several applications in the defence and in the electric power generation. The National Ignition Facility will operate in both direct and indirect driver modes, with a glass laser driver. However two other options have been developed to increase the energy efficiency: the Light Ion Pulsed Power program and the NIKE KrF laser. Heavy ion drivers are also investigated -Abstract only-. (TEC)

The antilock braking system anomaly: a drinking driver problem?

Science.gov (United States)

Harless, David W; Hoffer, George E

2002-05-01

Antilock braking systems (ABS) have held promise for reducing the incidence of accidents because they reduce stopping times on slippery surfaces and allow drivers to maintain steering control during emergency braking. Farmer et al. (Accident Anal. Prevent. 29 (1997) 745) provide evidence that antilock brakes are beneficial to nonoccupants: a set of 1992 model General Motors vehicles equipped with antilock brakes were involved in significantly fewer fatal crashes in which occupants of other vehicles, pedestrians, or bicyclists were killed. But, perversely, the risk of death for occupants of vehicles equipped with antilock brakes increased significantly after adoption. Farmer (Accident Anal. Prevent. 33 (2001) 361) updates the analysis for 1996- 1998 and finds a significant attenuation in the ABS anomaly. Researchers have put forward two hypotheses to explain this antilock brake anomaly: risk compensation and improper operation of antilock brake-equipped vehicles. We provide strong evidence for the improper operation hypothesis by showing that the antilock brake anomaly is confined largely to drinking drivers. Further, we show that the attenuation phenomenon occurs consistently after the first three to four years of vehicle service.

A driver-adaptive stability control strategy for sport utility vehicles

Science.gov (United States)

Zhu, Shenjin; He, Yuping

2017-08-01

Conventional vehicle stability control (VSC) systems are designed for average drivers. For a driver with a good driving skill, the VSC systems may be redundant; for a driver with a poor driving skill, the VSC intervention may be inadequate. To increase safety of sport utility vehicles (SUVs), this paper proposes a novel driver-adaptive VSC (DAVSC) strategy based on scaling the target yaw rate commanded by the driver. The DAVSC system is adaptive to drivers' driving skills. More control effort would be exerted for drivers with poor driving skills, and vice versa. A sliding mode control (SMC)-based differential braking (DB) controller is designed using a three degrees of freedom (DOF) yaw-plane model. An eight DOF nonlinear yaw-roll model is used to simulate the SUV dynamics. Two driver models, namely longitudinal and lateral, are used to 'drive' the virtual SUV. By integrating the virtual SUV, the DB controller, and the driver models, the performance of the DAVSC system is investigated. The simulations demonstrate the effectiveness of the DAVSC strategy.

Drivers' Visual Characteristics when Merging onto or Exiting an Urban Expressway.

Directory of Open Access Journals (Sweden)

Ying Cheng

Full Text Available The aim of this study is to examine drivers' visual and driving behavior while merging onto or exiting an urban expressway with low and high traffic densities. The analysis was conducted according to three periods (approaching, merging or exiting, and accelerating or decelerating. A total of 10 subjects (8 males and 2 females with ages ranging from 25 to 52 years old (M = 30.0 years old participated in the study. The research was conducted in a natural driving situation, and the drivers' eye movements were monitored and recorded using an eye tracking system. The results show that the influence of traffic density on the glance duration and scan duration is more significant when merging than when exiting. The results also demonstrate that the number of glances and the mean glance duration are mainly related to the driving task (e.g., the merging period. Therefore, drivers' visual search strategies mainly depend on the current driving task. With regard to driving behavior, the variation tendencies of the duration and the velocity of each period are similar. These results support building an automated driving assistant system that can automatically identify gaps and accelerate or decelerate the car accordingly or provide suggestions to the driver to do so.

[Occupational stress situation analysis of different types of train drivers].

Science.gov (United States)

Zhou, Wenhui; Gu, Guizhen; Wu, Hui; Yu, Shanfa

2014-11-01

To analyze the status of occupational stress in different types of train drivers. By using cluster sampling method, a cross-sectional study was conducted in 1 339 train drivers (including 289 passenger train drivers, 637 freight trains drivers, 339 passenger shunting train drivers, and 74 high speed rail drivers) from a Railway Bureau depot. The survey included individual factors, occupational stress factors, stress response factors and stress mitigating factors. The occupational stress factors, stress response factors and mitigating factors were measured by the revised effort-reward imbalance (ERI) model questionnaires and occupational stress measurement scale. By using the method of covariance analysized the difference of occupational stress factors of all types train drivers, the method of Stepwise regression was used to analyze the effection (R(2)) of occupational stress factors and stress mitigating factors on stress response factors. Covariance analysis as covariates in age, education level, length of service and marital status showed that the scores of ERI (1.58 ± 0.05), extrinsic effort (19.88 ± 0.44), rewards (23.43 ± 0.43), intrinsic effort (17.86 ± 0.36), physical environment (5.70 ± 0.22), social support (30.51 ± 0.88) and daily tension (10.27 ± 0.38 ) of high speed rail drivers were higher than other drivers (F values were 6.06, 11.32, 7.05, 13.25, 5.20, 9.48 and 6.14 respectively, P occupational stress factors and mitigating factors to depressive symptoms of train drivers was high speed rail drivers (R(2) = 0.64), passenger train drivers (R(2) = 0.44), passenger shunting train drivers (R(2) = 0.39), freight trains drivers (R(2) = 0.38); job satisfaction of train drivers was high speed rail drivers (R(2) = 0.68), passenger train drivers (R(2) = 0.62), freight trains drivers (R(2) = 0.43), passenger shunting train drivers(R(2) = 0.38); to daily tension of train drivers was high speed rail drivers (R(2) = 0.54), passenger train drivers (R(2) = 0

A new design of pulsed laser diode driver system for multistate quantum key distribution

Science.gov (United States)

Abdullah, M. S.; Jamaludin, M. Z.; Witjaksono, G.; Mokhtar, M. H. H.

2011-07-01

In this paper, we describe a new design of laser diode driver system based on MOSFET current mirror and digital signal controller (DSC). The system is designed to emit stream pairs of photons from three semiconductor laser diodes. The DSC is able to switch between the three laser diodes at constant rate. The duty cycle is maintained at 1% in order to reduce its thermal effect and thus prolong the laser diodes' life cycles. The MOSFET current mirror circuits are capable of delivering constant modulation current with peak current up to 58 mA to each laser diode. This laser driver system will allow the generating biphotons automatically with qubit rate around 8-13% for μ less than or equal to 1, thus making it practical for six-states quantum key distribution implementation.

OpenNebula KVM SR-IOV driver

CSIR Research Space (South Africa)

Macleod, D

2013-05-01

Full Text Available With the recent release of an OFED which supports SR-IOV on Infiniband HCAs it is now possible to use verbs from inside a VM. This VMM driver supports these Infiniband HCAs, and any other SR-IOV network device, in OpenNebula....

Supporting driver headway choice : The effects of discrete headway feedback when following headway instructions

NARCIS (Netherlands)

Risto, M.; Martens, M.H.

2014-01-01

With specific headway instructions drivers are not able to attain the exact headways as instructed. In this study, the effects of discrete headway feedback (and the direction of headway adjustment) on headway accuracy for drivers carrying out time headway instructions were assessed experimentally.

Supporting driver headway choice: The effects of discrete headway feedback when following headway instructions

NARCIS (Netherlands)

Risto, Malte; Martens, Marieke Hendrikje

2014-01-01

With specific headway instructions drivers are not able to attain the exact headways as instructed. In this study, the effects of discrete headway feedback (and the direction of headway adjustment) on headway accuracy for drivers carrying out time headway instructions were assessed experimentally.

Tracking progress in teenage driver crash risk in the United States since the advent of graduated driver licensing programs.

Science.gov (United States)

McCartt, Anne T; Teoh, Eric R

2015-06-01

This study examined U.S. teenagers' crash rates since 1996, when the first graduated driver licensing (GDL) program in the United State was implemented. Passenger vehicle driver crash involvement rates for 16-19 and 30-59 (middle-aged) year-olds were examined, using data from the Fatality Analysis Reporting System, National Automotive Sampling System General Estimates System, Census Bureau, and National Household Travel Surveys. Per capita fatal and police-reported crash rates in 2012 were lower for 16year-olds than for middle-aged drivers but older teenagers' rates were higher. Mileage-based fatal and police-reported crash rates in 2008 were higher for teenagers than for middle-aged drivers and higher for 16-17year-olds than for older teenagers. In 1996-2012, teenagers' per capita fatal and police-reported crash rates declined sharply, especially for 16-17year-olds, and more so than for middle-aged drivers. Substantial declines also occurred in teenagers' mileage-based fatal and police-reported crash rates from 1995-96 to 2008, generally more so than for middle-aged drivers. Regarding factors in fatal crashes in 1996 and 2012, proportions of young teenagers' crashes occurring at night and with multiple teenage passengers declined, more so than among older teenagers and middle-aged drivers. The proportion of fatally injured drivers who had been drinking declined for teenagers but changed little for middle-aged drivers. Improvements were not apparent in rates of driver errors or speeding among teenage drivers in fatal crashes. Teenage drivers' crash risk dropped during the period of implementation of GDL laws, especially fatal crash types targeted by GDL. However, teenagers' crash risk remains high, and important crash factors remain unaddressed by GDL. Although this study was not designed to examine the role of GDL, the results are consistent with the increased presence of such laws. More gains are achievable if states strengthen their laws. Copyright © 2015

Driver competence performance indicators using OTMR

Energy Technology Data Exchange (ETDEWEB)

Hassan EL Rashidy, R.A.

2016-07-01

The current practice for assessing driver competence performance is in-cab riding by driver managers. However, this paper investigates whether real-world driving data extracted from on-train monitoring recorders data (OTMR) can be used to assess the driver performance. A number of indicators were used to evaluate the drivers’ performance. These include: their use of the emergency bypass switch, the driver's reminder appliance as well as the driver’s reaction time. A study case illustrated the applicability of OTMR data to estimate the proposed indicators, which suggests that the indicators can be useful in the driver management system in addition to the current indicators. Furthermore, the proposed indicators could be used to tailor the driver training schemes up to their individual needs and evaluate their effectiveness. They could even be used for improving driver competence performance and reducing crash involvement by revealing potentially detrimental driving performance. (Author)

Life Support Filtration System Trade Study for Deep Space Missions

Science.gov (United States)

Agui, Juan H.; Perry, Jay L.

2017-01-01

The National Aeronautics and Space Administrations (NASA) technical developments for highly reliable life support systems aim to maximize the viability of long duration deep space missions. Among the life support system functions, airborne particulate matter filtration is a significant driver of launch mass because of the large geometry required to provide adequate filtration performance and because of the number of replacement filters needed to a sustain a mission. A trade analysis incorporating various launch, operational and maintenance parameters was conducted to investigate the trade-offs between the various particulate matter filtration configurations. In addition to typical launch parameters such as mass, volume and power, the amount of crew time dedicated to system maintenance becomes an increasingly crucial factor for long duration missions. The trade analysis evaluated these parameters for conventional particulate matter filtration technologies and a new multi-stage particulate matter filtration system under development by NASAs Glenn Research Center. The multi-stage filtration system features modular components that allow for physical configuration flexibility. Specifically, the filtration system components can be configured in distributed, centralized, and hybrid physical layouts that can result in considerable mass savings compared to conventional particulate matter filtration technologies. The trade analysis results are presented and implications for future transit and surface missions are discussed.

Schoolbus driver performance can be improved with driver training ...

African Journals Online (AJOL)

The Safe Travel to School Programme was recently implemented by a national child safety agency, with a focus on driver road safety awareness, defensive ... of a vehicle telematics tracking system with regular, individual driving behaviour ...

A spring-mass-damper system dynamics-based driver-vehicle integrated model for representing heterogeneous traffic

Science.gov (United States)

Munigety, Caleb Ronald

2018-04-01

The traditional traffic microscopic simulation models consider driver and vehicle as a single unit to represent the movements of drivers in a traffic stream. Due to this very fact, the traditional car-following models have the driver behavior related parameters, but ignore the vehicle related aspects. This approach is appropriate for homogeneous traffic conditions where car is the major vehicle type. However, in heterogeneous traffic conditions where multiple vehicle types are present, it becomes important to incorporate the vehicle related parameters exclusively to account for the varying dynamic and static characteristics. Thus, this paper presents a driver-vehicle integrated model hinged on the principles involved in physics-based spring-mass-damper mechanical system. While the spring constant represents the driver’s aggressiveness, the damping constant and the mass component take care of the stability and size/weight related aspects, respectively. The proposed model when tested, behaved pragmatically in representing the vehicle-type dependent longitudinal movements of vehicles.

Detecting Driver Drowsiness Based on Sensors: A Review

Directory of Open Access Journals (Sweden)

Kenneth Sundaraj

2012-12-01

Full Text Available In recent years, driver drowsiness has been one of the major causes of road accidents and can lead to severe physical injuries, deaths and significant economic losses. Statistics indicate the need of a reliable driver drowsiness detection system which could alert the driver before a mishap happens. Researchers have attempted to determine driver drowsiness using the following measures: (1 vehicle-based measures; (2 behavioral measures and (3 physiological measures. A detailed review on these measures will provide insight on the present systems, issues associated with them and the enhancements that need to be done to make a robust system. In this paper, we review these three measures as to the sensors used and discuss the advantages and limitations of each. The various ways through which drowsiness has been experimentally manipulated is also discussed. We conclude that by designing a hybrid drowsiness detection system that combines non-intusive physiological measures with other measures one would accurately determine the drowsiness level of a driver. A number of road accidents might then be avoided if an alert is sent to a driver that is deemed drowsy.

Modeling and Recognizing Driver Behavior Based on Driving Data: A Survey

Directory of Open Access Journals (Sweden)

Wenshuo Wang

2014-01-01

Full Text Available In recent years, modeling and recognizing driver behavior have become crucial to understanding intelligence transport systems, human-vehicle systems, and intelligent vehicle systems. A wide range of both mathematical identification methods and modeling methods of driver behavior are presented from the control point of view in this paper based on the driving data, such as the brake/throttle pedal position and the steering wheel angle, among others. Subsequently, the driver’s characteristics derived from the driver model are embedded into the advanced driver assistance systems, and the evaluation and verification of vehicle systems based on the driver model are described.

Deep Learning-Based Gaze Detection System for Automobile Drivers Using a NIR Camera Sensor.

Science.gov (United States)

Naqvi, Rizwan Ali; Arsalan, Muhammad; Batchuluun, Ganbayar; Yoon, Hyo Sik; Park, Kang Ryoung

2018-02-03

A paradigm shift is required to prevent the increasing automobile accident deaths that are mostly due to the inattentive behavior of drivers. Knowledge of gaze region can provide valuable information regarding a driver's point of attention. Accurate and inexpensive gaze classification systems in cars can improve safe driving. However, monitoring real-time driving behaviors and conditions presents some challenges: dizziness due to long drives, extreme lighting variations, glasses reflections, and occlusions. Past studies on gaze detection in cars have been chiefly based on head movements. The margin of error in gaze detection increases when drivers gaze at objects by moving their eyes without moving their heads. To solve this problem, a pupil center corneal reflection (PCCR)-based method has been considered. However, the error of accurately detecting the pupil center and corneal reflection center is increased in a car environment due to various environment light changes, reflections on glasses surface, and motion and optical blurring of captured eye image. In addition, existing PCCR-based methods require initial user calibration, which is difficult to perform in a car environment. To address this issue, we propose a deep learning-based gaze detection method using a near-infrared (NIR) camera sensor considering driver head and eye movement that does not require any initial user calibration. The proposed system is evaluated on our self-constructed database as well as on open Columbia gaze dataset (CAVE-DB). The proposed method demonstrated greater accuracy than the previous gaze classification methods.

Driver assistant system for industrial vehicles; Fahrerassistenzsysteme fuer Nutzfahrzeuge

Energy Technology Data Exchange (ETDEWEB)

Winterhagen, J.

1999-10-01

It is the intention of DaimlerChrysler AG to automatize future industrial vehicles by means of driver assistant systems. The components - from automatic distance control to fully electric steering - are in different stages of maturity. Some prototypes were presented recently at the Papenburg test site. [German] Fahrerassistenzsysteme werden das Nutzfahrzeug der Zukunft nach Vorstellungen der DaimlerChrysler AG weitestgehend automatisieren. Die dazu notwendigen Techniken - vom automatischen Abstandsregler bis zur vollelektrischen Lenkung - haben unterschiedliche Reifegrade. Einige Prototypen stellte das Unternehmen kuerzlich auf dem Pruefgelaende Papenburg vor. (orig.)

A novel active heads-up display for driver assistance.

Science.gov (United States)

Doshi, Anup; Cheng, Shinko Yuanhsien; Trivedi, Mohan Manubhai

2009-02-01

In this paper, we introduce a novel laser-based wide-area heads-up windshield display which is capable of actively interfacing with a human as part of a driver assistance system. The dynamic active display (DAD) is a unique prototype interface that presents safety-critical visual icons to the driver in a manner that minimizes the deviation of his or her gaze direction without adding to unnecessary visual clutter. As part of an automotive safety system, the DAD presents alerts in the field of view of the driver only if necessary, which is based upon the state and pose of the driver, vehicle, and environment. This paper examines the effectiveness of DAD through a comprehensive comparative experimental evaluation of a speed compliance driver assistance system, which is implemented on a vehicular test bed. Three different types of display protocols for assisting a driver to comply with speed limits are tested on actual roadways, and these are compared with a conventional dashboard display. Given the inclination, drivers who are given an overspeed warning alert reduced the time required to slow down to the speed limit by 38% (p system.

Driver steering model for closed-loop steering function analysis

Science.gov (United States)

Bolia, Pratiksh; Weiskircher, Thomas; Müller, Steffen

2014-05-01

In this paper, a two level preview driver steering control model for the use in numerical vehicle dynamics simulation is introduced. The proposed model is composed of cascaded control loops: The outer loop is the path following layer based on potential field framework. The inner loop tries to capture the driver's physical behaviour. The proposed driver model allows easy implementation of different driving situations to simulate a wide range of different driver types, moods and vehicle types. The expediency of the proposed driver model is shown with the help of developed driver steering assist (DSA) function integrated with a conventional series production (Electric Power steering System with rack assist servo unit) system. With the help of the DSA assist function, the driver is prevented from over saturating the front tyre forces and loss of stability and controllability during cornering. The simulation results show different driver reactions caused by the change in the parameters or properties of the proposed driver model if the DSA assist function is activated. Thus, the proposed driver model is useful for the advanced driver steering and vehicle stability assist function evaluation in the early stage of vehicle dynamics handling and stability evaluation.

Traffic Safety through Driver Assistance and Intelligence

Directory of Open Access Journals (Sweden)

Heiner Bubb

2011-05-01

BMW, Daimler, Audi, Citroen, Lexus, VW, Opel, Peugeot, Renault, Chevrolet, Saab and Bosch. Both the contributions of research work concerning driving behavior analysis and driver assistance systems have to be aligned with a permanently updated interaction within the system of driver, vehicle and road traffic environment.

A Framework for Estimating Long Term Driver Behavior

Directory of Open Access Journals (Sweden)

Vijay Gadepally

2017-01-01

Full Text Available We present a framework for estimation of long term driver behavior for autonomous vehicles and vehicle safety systems. The Hybrid State System and Hidden Markov Model (HSS+HMM system discussed in this article is capable of describing the hybrid characteristics of driver and vehicle coupling. In our model, driving observations follow a continuous trajectory that can be measured to create continuous state estimates. These continuous state estimates can then be used to estimate the most likely driver state using decision-behavior coupling inherent to the HSS+HMM system. The HSS+HMM system is encompassed in a HSS structure and intersystem connectivity is determined by using signal processing and pattern recognition techniques. The proposed method is suitable for a number of autonomous and vehicle safety scenarios such as estimating intent of other vehicles near intersections or avoiding hazardous driving events such as unexpected lane changes. The long term driver behavior estimation system involves an extended HSS+HMM structure that is capable of including external information in the estimation process. Through the grafting and pruning of metastates, the HSS+HMM system can be dynamically updated to best represent driver choices given external information. Three application examples are also provided to elucidate the theoretical system.

Brakes, brake control and driver assistance systems function, regulation and components

CERN Document Server

2014-01-01

Braking systems have been continuously developed and improved throughout the last years. Major milestones were the introduction of antilock braking system (ABS) and electronic stability program. This reference book provides a detailed description of braking components and how they interact in electronic braking systems. Contents Motor vehicle safety.- Basic principles of vehicle dynamics.- Car braking systems.- Car braking-system components.- Wheel brakes.- Antilock breaking systems.- Traction control system.- Electronic stability program.- Automatic brake functions.- Hydraulic modulator.- Sensors for brake control.- Sensotronic brake control.- Active steering.- Occupant protection systems.- Driver assistance systems.- Adaptive cruise control.- Parking systems.- Instrumentation.- Orientation methods.- Navigation systems.- Workshop technology. The target groups Motor-vehicle technicians in education and vocational training Master-mechanics and technicians in garage-workshops Teachers and lecturers in vocation...

Microfabricated Ion Beam Drivers for Magnetized Target Fusion

Science.gov (United States)

Persaud, Arun; Seidl, Peter; Ji, Qing; Ardanuc, Serhan; Miller, Joseph; Lal, Amit; Schenkel, Thomas

2015-11-01

Efficient, low-cost drivers are important for Magnetized Target Fusion (MTF). Ion beams offer a high degree of control to deliver the required mega joules of driver energy for MTF and they can be matched to several types of magnetized fuel targets, including compact toroids and solid targets. We describe an ion beam driver approach based on the MEQALAC concept (Multiple Electrostatic Quadrupole Array Linear Accelerator) with many beamlets in an array of micro-fabricated channels. The channels consist of a lattice of electrostatic quadrupoles (ESQ) for focusing and of radio-frequency (RF) electrodes for ion acceleration. Simulations with particle-in-cell and beam envelope codes predict >10x higher current densities compared to state-of-the-art ion accelerators. This increase results from dividing the total ion beam current up into many beamlets to control space charge forces. Focusing elements can be biased taking advantage of high breakdown electric fields in sub-mm structures formed using MEMS techniques (Micro-Electro-Mechanical Systems). We will present results on ion beam transport and acceleration in MEMS based beamlets. Acknowledgments: This work is supported by the U.S. DOE under Contract No. DE-AC02-05CH11231.

VD-411 branch driver

International Nuclear Information System (INIS)

Gorbunov, N.V.; Karev, A.G.; Mal'tsev, Eh.I.; Morozov, B.A.

1985-01-01

The VD-411 branch driver for CAMAC moduli control by the SM-4 computer is described. The driver realizes data exchange with moduli disposed in 28 crates grouped in 4 branches. Data exchange can be carried out either in the program regime or in the regime of direct access to the memory. Fulfilment of 11 block regimes and one program regime is provided for. A possibility of individual programming of exchange methods in block regimes is left for users for organisation of quicker and most flexible data removal from the CAMAC moduli. In the regime of direct access the driver provides data transmission at the size up to 64 Kwords placing it in the computer memory of 2 M byte. High rate of data transmission and the developed system of interruptions ensure efficient utilization of the VD-411 branch driver at data removal from facilities in high energy physics experiments

The driver's role in the development of new infotainment- and driver-assistance systems in the car; Die Rolle des Fahrers bei der Entwicklung neuer Infotainment- und Fahrerassistenzsysteme

Energy Technology Data Exchange (ETDEWEB)

Christ, S.; Bauer, A. [Spiegel Institut Mannheim, Bruehl (Germany)

2003-07-01

In the following contribution we will stress the importance of including the driver in the development of new Infotainment- and Driver-Assistance Systems. The necessity to do so derives from ever increasing complexity of above systems as well as from growing cost pressure in the automotive industry. Furthermore, we will point out several possibilities including the driver in the development of above systems and illustrate them by practical examples. Finally, we will present methods with the help of which potential users can test future technology at an early design stage, where the engineer still disposes of a wide scope of design possibilities. (orig.) [German] Im folgenden Beitrag soll die Wichtigkeit der Einbeziehung des Fahrers in den Entwicklungsprozess neuer Infotainment- und Fahrerassistenzsysteme dargelegt und begruendet werden. Die Notwendigkeit hierzu leitet sich sowohl aus der zunehmenden Komplexitaet der Systeme sowie dem gewachsenen Kostendruck in der Automobilindustrie ab. Weiter werden unterschiedliche Moeglichkeiten der Integration des Fahrers in den Entwicklungsprozess vorgestellt und durch Fallbeispiele aus der Praxis verdeutlicht. Im letzten Teil werden Verfahren aufgezeigt, mit deren Hilfe zukuenftige Technik von potenziellen Nutzern zu einem Zeitpunkt getestet werden kann, zu dem der Entwickler noch weiten Gestaltungsspielraum besitzt. (orig.)

Quantitative analysis of the relationship between driver`s behavior and vehicle motion; Sharyo unten ni taisuru untensha no kyodo no teiryoka bunseki ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Nakagawa, H; Matsuura, Y [Osaka Sangyo University, Osaka (Japan); Masuda, T

1997-10-01

In order to study the subject of driving safety about the human-vehicle interaction, driver`s maneuvering behavior was shot by CCD-cameras installed in a cabin and the motion of traveling vehicle was simultaneously taken by VTR-cameras set on the test course. These pictures were analyzed using the three-dimensional image processing system (Peak Motus system). Consequently, this system was effectively able to use for these measurements and analysis and introduced the correlation between the vehicle movement and the driver`s action. 4 refs., 12 figs., 2 tabs.

Does assisted driving behavior lead to safety-critical encounters with unequipped vehicles' drivers?

Science.gov (United States)

Preuk, Katharina; Stemmler, Eric; Schießl, Caroline; Jipp, Meike

2016-10-01

With Intelligent Transport Systems (e.g., traffic light assistance systems) assisted drivers are able to show driving behavior in anticipation of upcoming traffic situations. In the years to come, the penetration rate of such systems will be low. Therefore, the majority of vehicles will not be equipped with these systems. Unequipped vehicles' drivers may not expect the driving behavior of assisted drivers. However, drivers' predictions and expectations can play a significant role in their reaction times. Thus, safety issues could arise when unequipped vehicles' drivers encounter driving behavior of assisted drivers. This is why we tested how unequipped vehicles' drivers (N=60) interpreted and reacted to the driving behavior of an assisted driver. We used a multi-driver simulator with three drivers. The three drivers were driving in a line. The lead driver in the line was a confederate who was followed by two unequipped vehicles' drivers. We varied the equipment of the confederate with an Intelligent Transport System: The confederate was equipped either with or without a traffic light assistance system. The traffic light assistance system provided a start-up maneuver before a light turned green. Therefore, the assisted confederate seemed to show unusual deceleration behavior by coming to a halt at an unusual distance from the stop line at the red traffic light. The unusual distance was varied as we tested a moderate (4m distance from the stop line) and an extreme (10m distance from the stop line) parameterization of the system. Our results showed that the extreme parametrization resulted in shorter minimal time-to-collision of the unequipped vehicles' drivers. One rear-end crash was observed. These results provided initial evidence that safety issues can arise when unequipped vehicles' drivers encounter assisted driving behavior. We recommend that future research identifies counteractions to prevent these safety issues. Moreover, we recommend that system developers

Does early training improve driving skills of young novice French drivers?

Science.gov (United States)

Freydier, Chloé; Berthelon, Catherine; Bastien-Toniazzo, Mireille

2016-11-01

The aim of this research was to study drivers' performances and divided attention depending on their initial training. The performances of young novice drivers who received early training, traditionally trained drivers and more experienced drivers were compared during a dual task consisting of a simulated car-following task and a number' parity judgment task. It was expected that, due to their limited driving experience, the young novice drivers would have more difficulty in adequately distributing their attention between the two tasks. Poorer performances by novice drivers than experienced drivers were therefore expected. The results indicate that traditionally trained drivers had more difficulties in speed regulation and maintaining their position in the lane than drivers with early training and experienced drivers. Performance impairment linked to driving inexperience was also found in the secondary task. The results were interpreted regarding the attentional resources involved in driving with a secondary task and supported the positive effects of French early training. Copyright © 2016 Elsevier Ltd. All rights reserved.

Lifetime prediction of LED lighting systems considering thermal coupling between LED sources and drivers

DEFF Research Database (Denmark)

Alfarog, Azzarn Orner; Qu, Xiaohui; Wang, Huai

2017-01-01

and accelerate the failure. In this paper, a new thermal model concerning the thermal coupling is proposed with Finite Element Method (FEM) simulation for parameter acquirement. The proposed model has a better estimation of the thermal stresses of key components in the LED lamps and therefore an improved...... separately, and then the thermal design is also optimized independently. In practice, the LED source and driver are usually compacted in a single fixture. The heat dissipated from LED source and driver will be coupled together and affect the heat transfer performance, which may degrade the whole system...

Understanding local-scale drivers of biodiversity outcomes in terrestrial protected areas.

Science.gov (United States)

Barnes, Megan D; Craigie, Ian D; Dudley, Nigel; Hockings, Marc

2017-07-01

Conservation relies heavily on protected areas (PAs) maintaining their key biodiversity features to meet global biodiversity conservation goals. However, PAs have had variable success, with many failing to fully maintain their biodiversity features. The current literature concerning what drives variability in PA performance is rapidly expanding but unclear, sometimes contradictory, and spread across multiple disciplines. A clear understanding of the drivers of successful biodiversity conservation in PAs is necessary to make them fully effective. Here, we conduct a comprehensive assessment of the current state of knowledge concerning the drivers of biological outcomes within PAs, focusing on those that can be addressed at local scales. We evaluate evidence in support of potential drivers to identify those that enable more successful outcomes and those that impede success and provide a synthetic review. Interactions are discussed where they are known, and we highlight gaps in understanding. We find that elements of PA design, management, and local and national governance challenges, species and system ecology, and sociopolitical context can all influence outcomes. Adjusting PA management to focus on actions and policies that influence the key drivers identified here could improve global biodiversity outcomes. © 2016 New York Academy of Sciences.

Visualization drivers for Geant4

International Nuclear Information System (INIS)

Beretvas, Andy

2005-01-01

This document is on Geant 4 visualization tools (drivers), evaluating pros and cons of each option, including recommendations on which tools to support at Fermilab for different applications. Four visualization drivers are evaluated. They re OpenGL, HepRep, DAWN and VRML. They all have good features, OpenGL provides graphic output with out an intermediate file. HepRep provides menus to assist the user. DAWN provides high quality plots and even for large files produces output quickly. VRML uses the smallest disk space for intermediate files. Large experiments at Fermilab will want to write their own display. They should proceed to make this display graphics independent. Medium experiment will probably want to use HepRep because of it's menu support. Smaller scale experiments will want to use OpenGL in the spirit of having immediate response, good quality output and keeping things simple

Driver's Behavior Modeling Using Fuzzy Logic

Directory of Open Access Journals (Sweden)

Sehraneh Ghaemi

2010-01-01

Full Text Available In this study, we propose a hierarchical fuzzy system for human in a driver-vehicle-environment system to model takeover by different drivers. The driver's behavior is affected by the environment. The climate, road and car conditions are included in fuzzy modeling. For obtaining fuzzy rules, experts' opinions are benefited by means of questionnaires on effects of parameters such as climate, road and car conditions on driving capabilities. Also the precision, age and driving individuality are used to model the driver's behavior. Three different positions are considered for driving and decision making. A fuzzy model called Model I is presented for modeling the change of steering angle and speed control by considering time distances with existing cars in these three positions, the information about the speed and direction of car, and the steering angle of car. Also we obtained two other models based on fuzzy rules called Model II and Model III by using Sugeno fuzzy inference. Model II and Model III have less linguistic terms than Model I for the steering angle and direction of car. The results of three models are compared for a driver who drives based on driving laws.

Far-infrared pedestrian detection for advanced driver assistance systems using scene context

Science.gov (United States)

Wang, Guohua; Liu, Qiong; Wu, Qingyao

2016-04-01

Pedestrian detection is one of the most critical but challenging components in advanced driver assistance systems. Far-infrared (FIR) images are well-suited for pedestrian detection even in a dark environment. However, most current detection approaches just focus on pedestrian patterns themselves, where robust and real-time detection cannot be well achieved. We propose a fast FIR pedestrian detection approach, called MAP-HOGLBP-T, to explicitly exploit the scene context for the driver assistance system. In MAP-HOGLBP-T, three algorithms are developed to exploit the scene contextual information from roads, vehicles, and background objects of high homogeneity, and we employ the Bayesian approach to build a classifier learner which respects the scene contextual information. We also develop a multiframe approval scheme to enhance the detection performance based on spatiotemporal continuity of pedestrians. Our empirical study on real-world datasets has demonstrated the efficiency and effectiveness of the proposed method. The performance is shown to be better than that of state-of-the-art low-level feature-based approaches.

Initial Stage Reference Search : Driver Simulators to Test Shared Controls, Limited Autonomy Vehicle Systems

Science.gov (United States)

2015-09-01

This literature review and reference scanning focuses on the use of driver simulators for semiautonomous (or shared control) vehicle systems (2012present), including related research from other modes of transportation (e.g., rail or aviation). Foc...

[Health reasons for work disability among municipal transport drivers].

Science.gov (United States)

Szubert, Zuzanna; Sobala, Wojciech

2005-01-01

The health condition of public transport drivers is one of the factors playing a role in assuring safety of passengers taking use of this kind of transportation means. Therefore, the assessment of pathologies occurring in this occupational group is essential from the prevention point of view. Drivers employed in the municipal transport system are at particular risk. The aim of the study was to define health reasons of work disability among bus and tram drivers in general and to indicate pathologies responsible for disabilities in particular. The study covered 940 drivers (including 788 men and 152 women) employed in a municipal transportation enterprise during the years 1996-2000. Bus (30%) and tram (22%) drivers as well as transport service workers (48%), aged over 45 years, but under the retirement age, were eligible for the study. The analysis of temporary work disability during a five-year period was based on sickness absence, sickness absence rate and the average duration of sickness absence. The analysis revealed that diseases of the circulatory system form the major group of pathologies responsible for total sickness absence among bus drivers (43%), tram drivers (27%) and transport service workers (27%). These disease are also a leading cause of earlier retirement. They mostly include ischemic heart disease in bus drivers and hypertension in tram drivers. Cancers (pleura, kidney and eye) were responsible for 9% of sickness absence in the group of male tram drivers, whereas endocrine, nutritional and metabolic diseases and immunity disorders (diabetes, disorders of thyroid gland) in 16% of female tram drivers. Diseases of the musculoskeletal system were major causes of sickness absence among female tram drivers (24%), whereas malignant and benign neoplasms of breast and uterine myoma in 24% of female transport service workers. The results of the analysis are in agreement with the literature findings and provide explicit evidence that employment in the

Examination of Supplemental Driver Training and Online Basic Driver Education

Science.gov (United States)

2012-06-01

This report describes supplemental driver training programs and online basic driver education. It coves supplemental driver training that : focused on knowledge and skills beyond those normally found in traditional driver education delivered in the U...

Drivers Advancing Oral Health in a Large Group Dental Practice Organization.

Science.gov (United States)

Simmons, Kristen; Gibson, Stephanie; White, Joel M

2016-06-01

Three change drivers are being implemented to high standards of patient centric and evidence-based oral health care within the context of a large multispecialty dental group practice organization based on the commitment of the dental hygienist chief operating officer and her team. A recent environmental scan elucidated 6 change drivers that can impact the provision of oral health care. Practitioners who can embrace and maximize aspects of these change drivers will move dentistry forward and create future opportunities. This article explains how 3 of these change drivers are being applied in a privately held, accountable risk-bearing entity that provides individualized treatment programs for more than 417,000 members. To facilitate integration of the conceptual changes related to the drivers, a multi-institutional, multidisciplinary, highly functioning collaborative work group was formed. The document Dental Hygiene at a Crossroads for Change(1) inspired the first author, a dental hygienist in a unique position as chief operating officer of a large group practice, to pursue evidence-based organizational change and to impact the quality of patient care. This was accomplished by implementing technological advances including dental diagnosis terminology in the electronic health record, clinical decision support, standardized treatment guidelines, quality metrics, and patient engagement to improve oral health outcomes at the patient and population levels. The systems and processes used to implement 3 change drivers into a large multi-practice dental setting is presented to inform and inspire others to implement change drivers with the potential for advancing oral health. Technology implementing best practices and improving patient engagement are excellent drivers to advance oral health and are an effective use of oral health care dollars. Improved oral health can be leveraged through technological advances to improve clinical practice. Copyright © 2016 Elsevier Inc

PCI hardware support in LIA-2 control system

International Nuclear Information System (INIS)

Bolkhovityanov, D.; Cheblakov, P.

2012-01-01

The control system of the LIA-2 accelerator is built on cPCI crates with *86- compatible processor boards running Linux. Slow electronics is connected via CAN-bus, while fast electronics (4 MHz and 200 MHz fast ADCs and 200 MHz timers) are implemented as cPCI/PMC modules. Several ways to drive PCI control electronics in Linux were examined. Finally a user-space drivers approach was chosen. These drivers communicate with hardware via a small kernel module, which provides access to PCI BARs and to interrupt handling. This module was named USPCI (User-Space PCI access). This approach dramatically simplifies creation of drivers, as opposed to kernel drivers, and provides high reliability (because only a tiny and thoroughly-debugged piece of code runs in kernel). LIA-2 accelerator was successfully commissioned, and the solution chosen has proven adequate and very easy to use. Besides, USPCI turned out to be a handy tool for examination and debugging of PCI devices direct from command-line. In this paper available approaches to work with PCI control hardware in Linux are considered, and USPCI architecture is described. (authors)

An Overview on Study of Identification of Driver Behavior Characteristics for Automotive Control

Directory of Open Access Journals (Sweden)

Na Lin

2014-01-01

Full Text Available Driver characteristics have been the research focus for automotive control. Study on identification of driver characteristics is provided in this paper in terms of its relevant research directions and key technologies involved. This paper discusses the driver characteristics based on driver’s operation behavior, or the driver behavior characteristics. Following the presentation of the fundamental of the driver behavior characteristics, the key technologies of the driver behavior characteristics are reviewed in detail, including classification and identification methods of the driver behavior characteristics, experimental design and data acquisition, and model adaptation. Moreover, this paper discusses applications of the identification of the driver behavior characteristics which has been applied to the intelligent driver advisory system, the driver safety warning system, and the vehicle dynamics control system. At last, some ideas about the future work are concluded.

What the drivers do and do not tell you: using verbal protocol analysis to investigate driver behaviour in emergency situations.

Science.gov (United States)

Banks, Victoria A; Stanton, Neville A; Harvey, Catherine

2014-01-01

Although task analysis of pedestrian detection can provide us with useful insights into how a driver may behave in emergency situations, the cognitive elements of driver decision-making are less well understood. To assist in the design of future Advanced Driver Assistance Systems, such as Autonomous Emergency Brake systems, it is essential that the cognitive elements of the driving task are better understood. This paper uses verbal protocol analysis in an exploratory fashion to uncover the thought processes underlying behavioural outcomes represented by hard data collected using the Southampton University Driving Simulator.

Are professional drivers less sleepy than non-professional drivers?

Science.gov (United States)

Anund, Anna; Ahlström, Christer; Fors, Carina; Åkerstedt, Torbjörn

2018-01-01

Objective It is generally believed that professional drivers can manage quite severe fatigue before routine driving performance is affected. In addition, there are results indicating that professional drivers can adapt to prolonged night shifts and may be able to learn to drive without decreased performance under high levels of sleepiness. However, very little research has been conducted to compare professionals and non-professionals when controlling for time driven and time of day. Method The aim of this study was to use a driving simulator to investigate whether professional drivers are more resistant to sleep deprivation than non-professional drivers. Differences in the development of sleepiness (self-reported, physiological and behavioral) during driving was investigated in 11 young professional and 15 non-professional drivers. Results Professional drivers self-reported significantly lower sleepiness while driving a simulator than non-professional drivers. In contradiction, they showed longer blink durations and more line crossings, both of which are indicators of sleepiness. They also drove faster. The reason for the discrepancy in the relation between the different sleepiness indicators for the two groups could be due to more experience to sleepiness among the professional drivers or possibly to the faster speed, which might unconsciously have been used by the professionals to try to counteract sleepiness. Conclusion Professional drivers self-reported significantly lower sleepiness while driving a simulator than non-professional drivers. However, they showed longer blink durations and more line crossings, both of which are indicators of sleepiness, and they drove faster.

Gender differences and demographic influences in perceived concern for driver safety and support for impaired driving countermeasures.

Science.gov (United States)

Butters, Jennifer; Mann, Robert E; Wickens, Christine M; Boase, Paul

2012-12-01

Driving safety, impaired driving, and legislation to address these concerns remain important issues. It is imperative countermeasures be targeted toward the most appropriate groups. This paper explores the potential relationship between gender and driving attitudes toward safety issues and impaired-driving countermeasures. The data are from the 2007 Impaired Driving Survey commissioned by Transport Canada and Mothers Against Drunk Driving (MADD) Canada. The survey is a, stratified by region, telephone survey of 1,514 Canadian drivers 18years of age and older with a valid driver's license who had driven within the past 30days. The findings illustrate a consistent impact of gender on these issues. Other variables were also identified as relevant factors although less consistently. Current findings suggest that strategies for building support for interventions, or for changing risk perception/concern for risky driving behaviors should be tailored by gender to maximize the potential for behavior change. This information may assist program and policy developers through the identification of more or less receptive target groups. Future research directions are also presented. Copyright © 2012 National Safety Council and Elsevier Ltd. All rights reserved.

Research on driver fatigue detection

Science.gov (United States)

Zhang, Ting; Chen, Zhong; Ouyang, Chao

2018-03-01

Driver fatigue is one of the main causes of frequent traffic accidents. In this case, driver fatigue detection system has very important significance in avoiding traffic accidents. This paper presents a real-time method based on fusion of multiple facial features, including eye closure, yawn and head movement. The eye state is classified as being open or closed by a linear SVM classifier trained using HOG features of the detected eye. The mouth state is determined according to the width-height ratio of the mouth. The head movement is detected by head pitch angle calculated by facial landmark. The driver's fatigue state can be reasoned by the model trained by above features. According to experimental results, drive fatigue detection obtains an excellent performance. It indicates that the developed method is valuable for the application of avoiding traffic accidents caused by driver's fatigue.

Prevalence of driver physical factors leading to unintentional lane departure crashes.

Science.gov (United States)

Cicchino, Jessica B; Zuby, David S

2017-07-04

Some lane-keeping assist systems in development and production provide autonomous braking and steering to correct unintentional lane drift but otherwise require drivers to fully control their vehicles. The goal of this study was to quantify the proportion of drivers involved in unintentional lane drift crashes who would be unable to regain control of their vehicles to inform the design of such systems. The NHTSA's National Motor Vehicle Crash Causation Survey collected in-depth, on-scene data for a nationally representative sample of 5,470 U.S. police-reported passenger vehicle crashes during 2005-2007 that occurred between 6 a.m. and midnight and for which emergency medical services were dispatched. The physical states of drivers involved in the 631 lane drift crashes in the sample, which represented 259,034 crashes nationally, were characterized. Thirty-four percent of drivers who crashed because they drifted from their lanes were sleeping or otherwise incapacitated. These drivers would be unlikely to regain full control of their vehicles if an active safety system prevented their initial drift. An additional 13% of these drivers had a nonincapacitating medical issue, blood alcohol concentration (BAC) ≥ 0.08%, or other physical factor that may not allow them to regain full vehicle control. When crashes involved serious or fatal injuries, 42% of drivers who drifted were sleeping or otherwise incapacitated, and an additional 14% were impacted by a nonincapacitating medical issue, BAC ≥ 0.08%, or other physical factor. Designers of active safety systems that provide autonomous lateral control should consider that a substantial proportion of drivers at risk of lane drift crashes are incapacitated. Systems that provide only transient corrective action may not ultimately prevent lane departure crashes for these drivers, and drivers who do avoid lane drift crashes because of these systems may be at high risk of other types of crashes when they attempt to regain

Processes, Performance Drivers and ICT Tools in Human Resources Management

OpenAIRE

Oškrdal Václav; Pavlíček Antonín; Jelínková Petra

2011-01-01

This article presents an insight to processes, performance drivers and ICT tools in human resources (HR) management area. On the basis of a modern approach to HR management, a set of business processes that are handled by today’s HR managers is defined. Consequently, the concept of ICT-supported performance drivers and their relevance in the area of HR management as well as the relationship between HR business processes, performance drivers and ICT tools are defined. The theoretical outcomes ...

Advanced driver assistance systems: Using multimodal redundant warnings to enhance road safety.

Science.gov (United States)

Biondi, Francesco; Strayer, David L; Rossi, Riccardo; Gastaldi, Massimiliano; Mulatti, Claudio

2017-01-01

This study investigated whether multimodal redundant warnings presented by advanced assistance systems reduce brake response times. Warnings presented by assistance systems are designed to assist drivers by informing them that evasive driving maneuvers are needed in order to avoid a potential accident. If these warnings are poorly designed, they may distract drivers, slow their responses, and reduce road safety. In two experiments, participants drove a simulated vehicle equipped with a forward collision avoidance system. Auditory, vibrotactile, and multimodal warnings were presented when the time to collision was shorter than five seconds. The effects of these warnings were investigated with participants performing a concurrent cell phone conversation (Exp. 1) or driving in high-density traffic (Exp. 2). Braking times and subjective workload were measured. Multimodal redundant warnings elicited faster braking reaction times. These warnings were found to be effective even when talking on a cell phone (Exp. 1) or driving in dense traffic (Exp. 2). Multimodal warnings produced higher ratings of urgency, but ratings of frustration did not increase compared to other warnings. Findings obtained in these two experiments are important given that faster braking responses may reduce the potential for a collision. Copyright © 2016 Elsevier Ltd. All rights reserved.

Drivers and Limits for Transport

DEFF Research Database (Denmark)

Kristensen, Niels Buus; Nielsen, Thomas A. Sick; Gudmundsson, Henrik

This report summarizes key outcomes of the study ’Drivers and Limits’ that was supported for the period 2009-2013 by a research grant from the Danish Strategic Research Council. The project investigated - for the empirical context of Denmark - key driving forces behind transport growth, as well...

Injury mitigation estimates for an intersection driver assistance system in straight crossing path crashes in the United States.

Science.gov (United States)

Scanlon, John M; Sherony, Rini; Gabler, Hampton C

2017-05-29

Accounting for one fifth of all crashes and one sixth of all fatal crashes in the United States, intersection crashes are among the most frequent and fatal crash modes. Intersection advanced driver assistance systems (I-ADAS) are emerging vehicle-based active safety systems that aim to help drivers safely navigate intersections. The objective of this study was to estimate the number of crashes and number of vehicles with a seriously injured driver (Maximum Abbreviated Injury Scale [MAIS] 3+) that could be prevented or reduced if, for every straight crossing path (SCP) intersection crash, one of the vehicles had been equipped with an I-ADAS. This study retrospectively simulated 448 U.S. SCP crashes as if one of the vehicles had been equipped with I-ADAS. Crashes were reconstructed to determine the path and speeds traveled by the vehicles. Cases were then simulated with I-ADAS. A total of 30 variations of I-ADAS were considered in this study. These variations consisted of 5 separate activation timing thresholds, 3 separate computational latency times, and 2 different I-ADAS response modalities (i.e., a warning or autonomous braking). The likelihood of a serious driver injury was computed for every vehicle in every crash using impact delta-V. The results were then compiled across all crashes in order to estimate system effectiveness. The model predicted that an I-ADAS that delivers an alert to the driver has the potential to prevent 0-23% of SCP crashes and 0-25% of vehicles with a seriously injured driver. Conversely, an I-ADAS that autonomously brakes was found to have the potential to prevent 25-59% of crashes and 38-79% of vehicles with a seriously injured driver. I-ADAS effectiveness is a strong function of design. Increasing computational latency time from 0 to 0.5 s was found to reduce crash and injury prevention estimates by approximately one third. For an I-ADAS that delivers an alert, crash/injury prevention effectiveness was found to be very sensitive to

Embedded Platforms for Computer Vision-based Advanced Driver Assistance Systems: a Survey

OpenAIRE

Velez, Gorka; Otaegui, Oihana

2015-01-01

Computer Vision, either alone or combined with other technologies such as radar or Lidar, is one of the key technologies used in Advanced Driver Assistance Systems (ADAS). Its role understanding and analysing the driving scene is of great importance as it can be noted by the number of ADAS applications that use this technology. However, porting a vision algorithm to an embedded automotive system is still very challenging, as there must be a trade-off between several design requisites. Further...

DRIVER INATTENTION

Directory of Open Access Journals (Sweden)

Richard TAY

2004-01-01

Full Text Available Driver inattention, especially driver distraction, is an extremely influential but generally neglected contributing factor of road crashes. This paper explores some of the common behaviours associated with several common forms of driver inattention, with respect to their perceived crash risks, rates of self-reported behaviours and whether drivers regulate such behaviours depending on the road and traffic environment, and provides some policy recommendations to address issues raised.

Effects of cellular telephone manipulation on driver`s performance; Jidosha untenchu no keitai denwa shiyo sosa ni kanrensuru mondai no kenkyu

Energy Technology Data Exchange (ETDEWEB)

Tokunaga, R; Ozawa, M; Hagiwara, T [Hokkaido University, Sapporo (Japan); Takagi, H; Shimojo, A [Civil Engineering Research Institute of Hokkaido, Hokkaido (Japan)

1997-10-01

The present evaluates effects of cellular telephone manipulation on driver`s performance. The major independent variables were the reaction time and the mental workload. Hart et al. proposed the concept of the subjective mental workload. Experiments were conduced using a driving simulator without motion. Findings showed that the hands free system may provide less effect than the cellular telephone on the passenger seat on driver`s reaction time and mental workload. 4 refs., 2 tabs., 5 figs.

Repurposing PEV batteries : supporting renewables meet the drivers

International Nuclear Information System (INIS)

Bibeau, E.

2009-01-01

Methods of repurposing plug-in hybrid electric vehicle (PHEV) batteries were presented. Declining fossil fuel resources and increased environmental emissions are driving the need to repurpose PHEV batteries. Current paths to address energy drivers in transportation include the use of hydrogen; the reduction of tailpipe emissions; an increased use of biofuels; and reductions in fossil fuel usage. Electric mobility can also be combined with other methods to provide a sustainable long-term approach to transportation management. An increase in electric mobility will aid in ensuring that Canada's overall energy management strategy is successful. It was concluded that the addition of renewable energy resources will increase energy efficiency and lower energy demand. tabs., figs.

Relationships of working conditions, health problems and vehicle accidents in bus rapid transit (BRT) drivers.

Science.gov (United States)

Gómez-Ortiz, Viviola; Cendales, Boris; Useche, Sergio; Bocarejo, Juan P

2018-04-01

The aim of this study was to estimate accident risk rates and mental health of bus rapid transit (BRT) drivers based on psychosocial risk factors at work leading to increased stress and health problems. A cross-sectional research design utilized a self-report questionnaire completed by 524 BRT drivers. Some working conditions of BRT drivers (lack of social support from supervisors and perceived potential for risk) may partially explain Bogota's BRT drivers' involvement in road accidents. Drivers' mental health problems were associated with higher job strain, less support from co-workers, fewer rewards and greater signal conflict while driving. To prevent bus accidents, supervisory support may need to be increased. To prevent mental health problems, other interventions may be needed such as reducing demands, increasing job control, reducing amount of incoming information, simplifying current signals, making signals less contradictory, and revising rewards. © 2018 Wiley Periodicals, Inc.

Progress with situation assessment and risk prediction in advanced driver assistance systems : A survey

NARCIS (Netherlands)

Rendon-Velez, E.; Horváth, I.; Opiyo, E.Z.

2009-01-01

In the field of automotive safety, advanced driver assistance systems (ADAS) are receiving growing attention. Effective ADAS requires awareness of the actual driving situation, a reliable assessment of the risks, and making rapid decisions on assisting actions. This paper reviews the current

The importance of sight for drivers

Directory of Open Access Journals (Sweden)

Alicja Pas-Wyroślak

2013-06-01

Full Text Available Sight is the basic sense for drivers. Condition of the eye determines correct, comfortable and safe performance of the work as drivers. This article presents various factors influencing the sight condition. There are two groups of factors, external (environment, the kind and time of work, stress caused by work and internal (systemic and local disorders. All these factors can reduce significantly visual functions, such as visual acuity, field of vision, color vision, strereoscopic vision, twilight vision and glare sensitivity. There are also presented actual requirements for drivers and causes of the car accidents in various age groups. Impairments in vision functions can be dangerous for both the driver and other road users. Med Pr 2013;64(3:419–425

Driving fatigue in professional drivers: a survey of truck and taxi drivers.

Science.gov (United States)

Meng, Fanxing; Li, Shuling; Cao, Lingzhi; Li, Musen; Peng, Qijia; Wang, Chunhui; Zhang, Wei

2015-01-01

Fatigue among truck drivers has been studied extensively; however, less is known regarding the fatigue experience of taxi drivers in heavily populated metropolitan areas. This study aimed to compare the differences and similarities between truck and taxi driver fatigue to provide implications for the fatigue management and education of professional drivers. A sample of 274 truck drivers and 286 taxi drivers in Beijing was surveyed via a questionnaire, which included items regarding work characteristics, fatigue experience, accident information, attitude toward fatigue, and methods of counteracting fatigue. Driver fatigue was prevalent among professional drivers, and it was even more serious for taxi drivers. Taxi drivers reported more frequent fatigue experiences and were involved in more accidents. Among the contributing factors to fatigue, prolonged driving time was the most important factor identified by both driver groups. Importantly, the reason for the engagement in prolonged driving was neither due to the lack of awareness concerning the serious outcome of fatigue driving nor because of their poor detection of fatigue. The most probable reason was the optimism bias, as a result of which these professional drivers thought that fatigue was more serious for other drivers than for themselves, and they thought that they were effective in counteracting the effect of fatigue on their driving performance. Moreover, truck drivers tended to employ methods that require stopping to counteract fatigue, whereas taxi drivers preferred methods that were simultaneous with driving. Although both driver groups considered taking a nap as one of the most effective means to address fatigue, this method was not commonly used. Interestingly, these drivers were aware that the methods they frequently used were not the most effective means to counteract fatigue. This study provides knowledge on truck and taxi drivers' characteristics in fatigue experience, fatigue attitude, and

Knowledge-based driver assistance systems traffic situation description and situation feature relevance

CERN Document Server

Huelsen, Michael

2014-01-01

The comprehension of a traffic situation plays a major role in driving a vehicle. Interpretable information forms a basis for future projection, decision making and action performing, such as navigating, maneuvering and driving control. Michael Huelsen provides an ontology-based generic traffic situation description capable of supplying various advanced driver assistance systems with relevant information about the current traffic situation of a vehicle and its environment. These systems are enabled to perform reasonable actions and approach visionary goals such as injury and accident free driv

Identification of drivers for modular production

DEFF Research Database (Denmark)

Brunoe, Thomas Ditlev; Bossen, Jacob; Nielsen, Kjeld

2015-01-01

Todays competitive environment in industry creates a need for companies to enhance their ability to introduce new products faster. To increase rampup speed reconfigurable manufacturing systems is a promising concept, however to implement this production platforms and modular manufacturing...... is required. This paper presents an analysis whether and which module drivers from general product development can be applied to the development process of a modular manufacturing system. The result is a compiled list of modular drivers for manufacturing and examples of their use....

Fast and Precise Symbolic Analysis of Concurrency Bugs in Device Drivers

OpenAIRE

Deligiannis, P; Donaldson, AF; Rakamaric, Z

2015-01-01

? 2015 IEEE.Concurrency errors, such as data races, make device drivers notoriously hard to develop and debug without automated tool support. We present Whoop, a new automated approach that statically analyzes drivers for data races. Whoop is empowered by symbolic pairwise lockset analysis, a novel analysis that can soundly detect all potential races in a driver. Our analysis avoids reasoning about thread interleavings and thus scales well. Exploiting the race-freedom guarantees provided by W...

Reversing Control of a Car with a Trailer Using the Driver Assistance System

Directory of Open Access Journals (Sweden)

Jae Il Roh

2011-06-01

Full Text Available Passive trailer systems provide a variety of advantages in delivery and transportation applications. The transportation capacity of the truck with multiple trailers can be increased in proportion to the number of trailers. The cost of the car with trailers is much lower than the cost of multiple cars. However, the major drawback of the trailer system is that the control problem is difficult. We concentrate on the motion control problem of ʺpushingʺ trailers because pushing is much more difficult than ʺpullingʺ. In this paper, it is shown how the car with passive trailers can be easily controlled by the use of the proposed driver assist system and the motion control scheme. Since the keypad is the only additional device for the driver assist system, the proposed scheme can be implemented with the conventional trucks without many hardware modifications. The manual control strategy of pushing is established. The kinematic design of the passive trailer is adopted from the prior work (Park and Chung, 2004. The kinematic configuration design of the car with trailers is proposed for pushing control. The usefulness of the proposed scheme is experimentally verified with the small scale car with trailer system for the car parking problem. The parking control requires forward and reverse motion in narrow environment. It is shown that even beginners can easily control the pushing motion with the proposed scheme.

Reversing Control of a Car with a Trailer Using the Driver Assistance System

Directory of Open Access Journals (Sweden)

Jae Roh

2011-06-01

Full Text Available Passive trailer systems provide a variety of advantages in delivery and transportation applications. The transportation capacity of the truck with multiple trailers can be increased in proportion to the number of trailers. The cost of the car with trailers is much lower than the cost of multiple cars. However, the major drawback of the trailer system is that the control problem is difficult. We concentrate on the motion control problem of “pushing” trailers because pushing is much more difficult than “pulling”. In this paper, it is shown how the car with passive trailers can be easily controlled by the use of the proposed driver assist system and the motion control scheme. Since the keypad is the only additional device for the driver assist system, the proposed scheme can be implemented with the conventional trucks without many hardware modifications. The manual control strategy of pushing is established. The kinematic design of the passive trailer is adopted from the prior work (Park and Chung, 2004. The kinematic configuration design of the car with trailers is proposed for pushing control. The usefulness of the proposed scheme is experimentally verified with the small scale car with trailer system for the car parking problem. The parking control requires forward and reverse motion in narrow environment. It is shown that even beginners can easily control the pushing motion with the proposed scheme.

Physics at a New Fermilab Proton Driver

International Nuclear Information System (INIS)

Geer, Steve

2005-01-01

In 2004 the Fermilab Long Range Planning Committee identified a new high intensity Proton Driver as an attractive option for the future, primarily motivated by the recent exciting developments in neutrino physics. The Fermilab Director has requested further development of the physics case for a new Fermilab Proton Driver, exploring both its ability to support a World class neutrino program, and the other physics opportunities it would provide. A physics study has been ongoing for the last 6 months. The emerging physics case will be presented.

[Influencing factors for job satisfaction in train drivers in a railway bureau: an analysis of 1413 cases].

Science.gov (United States)

Gu, G Z; Yu, S F; Zhou, W H; Wu, H; Kang, L; Chen, R

2017-01-20

Objective: To investigate the influencing factors for job satisfaction in train drivers. Methods: In March 2012, cluster sampling was used to conduct a cross-sectional survey in 1413 male train drivers (including 301 passenger train drivers, 683 freight train drivers, 350 passenger shunting train drivers, and 79 high-speed train drivers) from a locomotive depot of a railway bureau. The occupational stress instruments, job content questionnaire, and effort-reward imbalance questionnaire were used to analyze job satisfaction, occupational stress factors, stress reaction, individual characteristics, coping strategies, and social support. Results: There were significant differences in job satisfaction score between the drivers with different posts, working years, ages, smoking status, and drinking status ( P analysis revealed that job satisfaction score was positively correlated with reward, working stability, promotion opportunity, positive emotion, social support, self-esteem, and coping strategy scores ( P analysis of variance showed that compared with the moderate and low job satisfaction groups, the high job satisfaction group had significantly higher reward, positive emotion, promotion opportunity, and role ambiguity scores ( P job satisfaction groups the low job satisfaction group had significantly higher scores of psychological needs, effort, role conflict, sleep disorders, daily stress, depressive symptom, negative emotion, drug use, intragroup conflict, and social support ( P job satisfaction group had a significantly higher score of self-esteem than the other two groups ( P analysis showed that the risk of job dissatisfaction in the drivers with low so-cial support and high daily stress was more than 2 times that in those with high social support and low daily stress ( OR =2.176 and 2.171) , and sleep disorders, effort, depressive symptom, low self-esteem, and role conflict were risk factors for job dissatisfaction ( OR =1.48-1.625). Conclusion: Occupational

i-Car: An Intelligent and Interactive Interface for Driver Assistance ...

African Journals Online (AJOL)

i-Car: An Intelligent and Interactive Interface for Driver Assistance System. ... techniques with pattern recognition, feature extraction, machine learning, object recognition, ... The system uses eye closure based decision algorithm to detect driver ...

A vision-based driver nighttime assistance and surveillance system based on intelligent image sensing techniques and a heterogamous dual-core embedded system architecture.

Science.gov (United States)

Chen, Yen-Lin; Chiang, Hsin-Han; Chiang, Chuan-Yen; Liu, Chuan-Ming; Yuan, Shyan-Ming; Wang, Jenq-Haur

2012-01-01

This study proposes a vision-based intelligent nighttime driver assistance and surveillance system (VIDASS system) implemented by a set of embedded software components and modules, and integrates these modules to accomplish a component-based system framework on an embedded heterogamous dual-core platform. Therefore, this study develops and implements computer vision and sensing techniques of nighttime vehicle detection, collision warning determination, and traffic event recording. The proposed system processes the road-scene frames in front of the host car captured from CCD sensors mounted on the host vehicle. These vision-based sensing and processing technologies are integrated and implemented on an ARM-DSP heterogamous dual-core embedded platform. Peripheral devices, including image grabbing devices, communication modules, and other in-vehicle control devices, are also integrated to form an in-vehicle-embedded vision-based nighttime driver assistance and surveillance system.

Supporting the Support System: How Assessment and Communication Can Help Patients and Their Support Systems.

Science.gov (United States)

Harkey, Jane; Young, Jared; Carter, Jolynne Jo; Demoratz, Michael

The benefits of having a support system, such as social relationships with close friends and family, have been well documented for patients with serious health issues. As scientific evidence has shown, individuals who have the lowest level of involvement in social relationships face a greater mortality risk. Support systems, however, are not infallible. Relationship stress can have a negative impact on people-patient and caregiver alike-behaviorally, psychosocially, and physiologically. The purpose of this article is to encourage case managers who take a patient-centered approach to also consider the existence and extent of the support system, as well as any stresses or tensions that are observable within the support system. Although the case manager is ethically obliged to advocate for the individual receiving case management services, that advocacy can be extended to the support system for the good of all. This discussion applies to numerous case management practices and work settings including (but not limited to) hospital-based case management, home health, geriatrics, catastrophic case management, mental health, palliative care, and end of life/hospice. As part of the assessment phase of the case management process, case managers determine the extent of the patient's support system or social support network such as family and close friends. Although their advocacy is primarily for the patient receiving case management services, case managers also become aware of the needs of the support system members as they face their loved one's serious illness, severe injury, geriatric care demands, or end of life. Case managers can use their communication skills, especially motivational interviewing, with patients and their support systems to identify stresses and issues that can impact the pursuit of health goals. In addition, case managers ensure that individuals and their support systems are kept informed such as about the health condition, stage of disease, plan of

Design and simulation of advanced charge recovery piezoactuator drivers

International Nuclear Information System (INIS)

Biancuzzi, G; Lemke, T; Woias, P; Goldschmidtboeing, F; Ruthmann, O; Schrag, H J; Vodermayer, B; Schmid, T

2010-01-01

The German Artificial Sphincter System project aims at the development of an implantable sphincter prosthesis driven by a piezoelectrically actuated micropump. The system has been designed to be fully implantable, i.e. the power supply is provided by a rechargeable lithium polymer battery. In order to provide sufficient battery duration and to limit battery dimensions, special effort has to be made to minimize power consumption of the whole system and, in particular, of the piezoactuator driver circuitry. Inductive charge recovery can be used to recover part of the charge stored within the actuator. We are going to present a simplified inductor-based circuit capable of voltage inversion across the actuator without the need of an additional negative voltage source. The dimension of the inductors required for such a concept is nevertheless significant. We therefore present a novel alternative concept, called direct switching, where the equivalent capacitance of the actuator is charged directly by a step-up converter and discharged by a step-down converter. We achieved superior performance compared to a simple inductor-based driver with the advantage of using small-size chip inductors. As a term of comparison, the performance of the aforementioned drivers is compared to a conventional driver that does not implement any charge recovery technique. With our design we have been able to achieve more than 50% reduction in power consumption compared to the simplest conventional driver. The new direct switching driver performs 15% better than an inductor-based driver. A novel, whole-system SPICE simulation is presented, where both the driving circuit and the piezoactuator are modeled making use of advanced nonlinear models. Such a simulation is a precious tool to design and optimize piezoactuator drivers

A drug identification system for intoxicated drivers based on a systematic review

Directory of Open Access Journals (Sweden)

Alfonso GONZÁLEZ

2016-07-01

Full Text Available Tests to detect the use of illegal substances among drivers are becoming more common. During these tests, a saliva test is performed and agents observe the driver to determine whether or not they are driving under the influence of psychoactive substances. During the joint control of alcohol and drugs, a breath test is performed followed by a saliva test. In addition, agents use a previously established observation questionnaire to evaluate external signs that the driver may present. This review aims to help expand and improve the questionnaire administered by the traffic officer to the driver, so that upon completing the questionnaire as indicated, it is possible to determine which drug corresponds to the symptoms displayed by the driver. The diagnosis will be facilitated by a software tool that employs the use of decision trees whose gain function has been modified to give different weights to signs and methods. A study was conducted on the symptoms and observable and/or easily detectable signs of drugs detected at sobriety checkpoints. This has enabled the creation of a test that determines the substance consumed by the driver. The proposal facilitates the detection of drugs with the data gathered from the test.

Free and open source software at CERN: integration of drivers in the Linux kernel

International Nuclear Information System (INIS)

Gonzalez Cobas, J.D.; Iglesias Gonsalvez, S.; Howard Lewis, J.; Serrano, J.; Vanga, M.; Cota, E.G.; Rubini, A.; Vaga, F.

2012-01-01

Most device drivers written for accelerator control systems suffer from a severe lack of portability due to the ad hoc nature of the code, often embodied with intimate knowledge of the particular machine it is deployed in. In this paper we challenge this practice by arguing for the opposite approach: development in the open, which in our case translates into the integration of our code within the Linux kernel. We make our case by describing the upstream merge effort of the tsi148 driver, a critical (and complex) component of the control system. The encouraging results from this effort have then led us to follow the same approach with two more ambitious projects, currently in the works: Linux support for the upcoming FMC boards and a new I/O subsystem. (authors)

Induction linac drivers for commercial heavy-ion beam fusion

International Nuclear Information System (INIS)

Keefe, D.

1987-11-01

This paper discusses induction linac drivers necessary to accelerate heavy ions at inertial fusion targets. Topics discussed are: driver configurations, the current-amplifying induction linac, high current beam behavior and emittance growth, new considerations for driver design, the heavy ion fusion systems study, and future studies. 13 refs., 6 figs., 1 tab

Detection of Driver Drowsiness Using Wavelet Analysis of Heart Rate Variability and a Support Vector Machine Classifier

Directory of Open Access Journals (Sweden)

Gang Li

2013-12-01

Full Text Available Driving while fatigued is just as dangerous as drunk driving and may result in car accidents. Heart rate variability (HRV analysis has been studied recently for the detection of driver drowsiness. However, the detection reliability has been lower than anticipated, because the HRV signals of drivers were always regarded as stationary signals. The wavelet transform method is a method for analyzing non-stationary signals. The aim of this study is to classify alert and drowsy driving events using the wavelet transform of HRV signals over short time periods and to compare the classification performance of this method with the conventional method that uses fast Fourier transform (FFT-based features. Based on the standard shortest duration for FFT-based short-term HRV evaluation, the wavelet decomposition is performed on 2-min HRV samples, as well as 1-min and 3-min samples for reference purposes. A receiver operation curve (ROC analysis and a support vector machine (SVM classifier are used for feature selection and classification, respectively. The ROC analysis results show that the wavelet-based method performs better than the FFT-based method regardless of the duration of the HRV sample that is used. Finally, based on the real-time requirements for driver drowsiness detection, the SVM classifier is trained using eighty FFT and wavelet-based features that are extracted from 1-min HRV signals from four subjects. The averaged leave-one-out (LOO classification performance using wavelet-based feature is 95% accuracy, 95% sensitivity, and 95% specificity. This is better than the FFT-based results that have 68.8% accuracy, 62.5% sensitivity, and 75% specificity. In addition, the proposed hardware platform is inexpensive and easy-to-use.

Study on Driver Visual Physiological Characteristics in Urban Traffic

Directory of Open Access Journals (Sweden)

Fengyuan Wang

2014-01-01

Full Text Available In the integrated traffic environment, human factor is always a main factor of the three elementary factors, besides the vehicle and road factor. The driver physiological and psychological characteristics have an important impact especially on traffic safety in urban road traffic conditions. Some typical traffic scenes in condition of urban road, such as light signal control at intersection, overtaking, and passing, are selected for condition analysis. An eye movement apparatus was used to obtain driver eye closure, blink frequency, and other visual physiological indicators in the traffic conditions of urban road. The regular patterns of driver visual characteristics in the corresponding scenes were analyzed in detail to provide data and theoretical support for the further research on traffic safety of urban environment from the viewpoint of driver psychology and behavior.

EMERGENCE OF "DRIVERS" FOR THE IMPLEMENTATION OF HEALTH TECHNOLOGY ASSESSMENT.

Science.gov (United States)

Castro Jaramillo, Hector Eduardo; Moreno-Mattar, Ornella; Osorio-Cuevas, Diana

2016-01-01

Health technology assessment (HTA) examines the consequences of the application of health technologies and is aimed at better informing decision-makers. Over the past 30 years, different countries have implemented HTA organizations. Colombia established by law its own HTA agency (IETS) in 2011 which started operations in November 2012. The aim of this study was to assess the feasibility of conducting and using HTA to inform decision-making in this context. Through a qualitative approach, ten "drivers" emerged with the ability to help or hinder HTA development in this context: availability and quality of data, implementation strategy, cultural aspects, local capacity, financial support, policy/political support, globalization, stakeholder pressure, health system context, and usefulness perception. Semi-structured interviews were conducted with key HTA researchers, after following rigorous transcription, and thematic content analysis, those aspects that may be barriers or facilitator for HTA development and use in Colombia were identified. Although HTA has become a tool to inform decision-making around the world, its use may vary according to setting. Determining those aspects which may enable or interfere with HTA development and use in Colombia may be useful for other countries when considering the establishment of HTA systems. The conceptual transferability of concepts like "drivers" with caveats may be of interest for similar settings trying to incorporate HTA processes and institutions into systematic decision-making.

Recommendations for CAMAC Serial Highway drivers and LAM Graders for the SCC-L2 Serial Crate Controller

International Nuclear Information System (INIS)

1978-01-01

The functional requirements of Drivers for the CAMAC Serial Highway defined in IEEE Standard 595-1976 are described. The description is independent of the implementation, and in particular no assumption is made about the boundary between hardware and software within the Driver. Topics covered are the user interface, the supporting system services required, demand handling, and a detailed discussion of the message analysis for various levels of error recovery. An appendix describes the recommended features of LAM Graders for use with the Serial Crate Controller Type L2 of IEEE Std 595-1976

Using shadow page cache to improve isolated drivers performance.

Science.gov (United States)

Zheng, Hao; Dong, Xiaoshe; Wang, Endong; Chen, Baoke; Zhu, Zhengdong; Liu, Chengzhe

2015-01-01

With the advantage of the reusability property of the virtualization technology, users can reuse various types and versions of existing operating systems and drivers in a virtual machine, so as to customize their application environment. In order to prevent users' virtualization environments being impacted by driver faults in virtual machine, Chariot examines the correctness of driver's write operations by the method of combining a driver's write operation capture and a driver's private access control table. However, this method needs to keep the write permission of shadow page table as read-only, so as to capture isolated driver's write operations through page faults, which adversely affect the performance of the driver. Based on delaying setting frequently used shadow pages' write permissions to read-only, this paper proposes an algorithm using shadow page cache to improve the performance of isolated drivers and carefully study the relationship between the performance of drivers and the size of shadow page cache. Experimental results show that, through the shadow page cache, the performance of isolated drivers can be greatly improved without impacting Chariot's reliability too much.

An Evolutionary Approach to Driving Tendency Recognition for Advanced Driver Assistance Systems

Directory of Open Access Journals (Sweden)

Lee Jong-Hyun

2016-01-01

Full Text Available Driving tendency recognition is important for constructing Advanced Driver Assistance Systems (ADAS. However, it had not been a lot of research using vehicle sensing data, due to the high difficulty to define it. In this paper, we attempt to improve the learning capability of a machine learning method using evolutionary computation. We propose a driving tendency recognition method, with consideration of data characteristics. Comparison of our classification system with conventional methods demonstrated the effectiveness and accuracy over 92% in our system. Our proposed evolutionary approach is confirmed that improve the classification accuracy of the learning method through evolution in the experiment.

Steering disturbance rejection using a physics-based neuromusculoskeletal driver model

Science.gov (United States)

Mehrabi, Naser; Sharif Razavian, Reza; McPhee, John

2015-10-01

The aim of this work is to develop a comprehensive yet practical driver model to be used in studying driver-vehicle interactions. Drivers interact with their vehicle and the road through the steering wheel. This interaction forms a closed-loop coupled human-machine system, which influences the driver's steering feel and control performance. A hierarchical approach is proposed here to capture the complexity of the driver's neuromuscular dynamics and the central nervous system in the coordination of the driver's upper extremity activities, especially in the presence of external disturbance. The proposed motor control framework has three layers: the first (or the path planning) plans a desired vehicle trajectory and the required steering angles to perform the desired trajectory; the second (or the musculoskeletal controller) actuates the musculoskeletal arm to rotate the steering wheel accordingly; and the final layer ensures the precision control and disturbance rejection of the motor control units. The physics-based driver model presented here can also provide insights into vehicle control in relaxed and tensed driving conditions, which are simulated by adjusting the driver model parameters such as cognition delay and muscle co-contraction dynamics.

A path-following driver/vehicle model with optimized lateral dynamic controller

Directory of Open Access Journals (Sweden)

Behrooz Mashadi

Full Text Available Reduction in traffic congestion and overall number of accidents, especially within the last decade, can be attributed to the enormous progress in active safety. Vehicle path following control with the presence of driver commands can be regarded as one of the important issues in vehicle active safety systems development and more realistic explanation of vehicle path tracking problem. In this paper, an integrated driver/DYC control system is presented that regulates the steering angle and yaw moment, considering driver previewed path. Thus, the driver previewed distance, the heading error and the lateral deviation between the vehicle and desired path are used as inputs. Then, the controller determines and applies a corrective steering angle and a direct yaw moment to make the vehicle follow the desired path. A PID controller with optimized gains is used for the control of integrated driver/DYC system. Genetic Algorithm as an intelligent optimization method is utilized to adapt PID controller gains for various working situations. Proposed integrated driver/DYC controller is examined on lane change manuvers andthe sensitivity of the control system is investigated through the changes in the driver model and vehicle parameters. Simulation results show the pronounced effectiveness of the controller in vehicle path following and stability.

Tarantula: Killing driver bugs before they hatch

DEFF Research Database (Denmark)

Lawall, Julia Laetitia; Muller, Gilles; Urunuela, Richard

2005-01-01

The Linux operating system is undergoing continual evolution. Evolution in the kernel and generic driver modules often triggers the need for corresponding evolutions in specific device drivers. Such collateral evolutions are tedious, because of the large number of device drivers, and error......-prone, because of the complexity of the code modifications involved. We propose an automatic tool, Tarantula, to aid in this process. In this paper, we examine some recent evolutions in Linux and the collateral evolutions they trigger, and assess the corresponding requirements on Tarantula....

Locomotor diseases among male long-haul truck drivers and other professional drivers

DEFF Research Database (Denmark)

Jensen, Anker; Kaerlev, Linda; Tüchsen, Finn

2007-01-01

-249) and for other truck drivers (SHR: 130, 95% CI: 108-156) compared to bus drivers (SHR: 110, 95% CI: 79-149). All drivers had high SHR for lesions of the ulnar nerve (SHR: 159, 95% CI: 119-207), especially bus drivers (SHR: 197, 95% CI: 116-311). Long-haul truck drivers had high SHRs for synovitis and bursitis...

Integrating cost information with health management support system: an enhanced methodology to assess health care quality drivers.

Science.gov (United States)

Kohli, R; Tan, J K; Piontek, F A; Ziege, D E; Groot, H

1999-08-01

Changes in health care delivery, reimbursement schemes, and organizational structure have required health organizations to manage the costs of providing patient care while maintaining high levels of clinical and patient satisfaction outcomes. Today, cost information, clinical outcomes, and patient satisfaction results must become more fully integrated if strategic competitiveness and benefits are to be realized in health management decision making, especially in multi-entity organizational settings. Unfortunately, traditional administrative and financial systems are not well equipped to cater to such information needs. This article presents a framework for the acquisition, generation, analysis, and reporting of cost information with clinical outcomes and patient satisfaction in the context of evolving health management and decision-support system technology. More specifically, the article focuses on an enhanced costing methodology for determining and producing improved, integrated cost-outcomes information. Implementation issues and areas for future research in cost-information management and decision-support domains are also discussed.

Cyclist-related content in novice driver education and training.

Science.gov (United States)

Bonham, Jennifer; Johnson, Marilyn

2018-02-01

In Australia, the increasing public profile and policy interest in cycling contrasts with variable cycling participation rates across jurisdictions (Australian Bicycle Council, 2017) and lack of cyclist-specific infrastructure. Cyclists and drivers often share road space, usually without indication from the built environment about how to maximise each other's safety and utility. Yet despite this regular interaction, cyclists are largely absent from the driver licensing process in Australia. That is, novice drivers are not taught how to share the road with cyclists. This case study used a mixed methods approach to examine the cyclist-related content in the Graduated Driver Licensing System (GDLS) in the Australian Capital Territory (ACT). The case study was conducted in four stages: 1) content analysis of all documents used through the GDLS; 2) observations of the Road Ready course and learner driver lessons; 3) online survey; and, 4) semi-structured interviews. Cyclists are rarely mentioned in the GDLS in the ACT and references often constructed cyclists as problematic or were based in instructors' personal opinion (rather than scripted responses). Outcomes from this study have directly informed a new vulnerable road user driver licence competency in the ACT and findings include recommendations for greater inclusion of cyclists in the driver licensing system. Copyright © 2017 Elsevier Ltd. All rights reserved.

A Stochastic LWR Model with Consideration of the Driver's Individual Property

International Nuclear Information System (INIS)

Tang Tieqiao; Wang Yunpeng; Yu Guizhen; Huang Haijun

2012-01-01

In this paper, we develop a stochastic LWR model based on the influences of the driver's individual property on his/her perceived density and speed deviation. The numerical results show that the driver's individual property has great effects on traffic flow only when the initial density is moderate, i.e., at this time, oscillating traffic flow will occur and the oscillating phenomena in the traffic system consisting of the conservative and aggressive drivers is more serious than that in the traffic system consisting of the conservative (aggressive) drivers.

Schoolbus driver performance can be improved with driver training, safety incentivisation, and vehicle roadworthy modifications

Directory of Open Access Journals (Sweden)

A van Niekerk

2017-03-01

Full Text Available In South Africa (SA, the school transport industry provides millions of children with a means of travelling to and from school. The industry has, however, been reported to be plagued by widespread safety concerns. The consequent road traffic incidents have often been attributed to driver factors, including driving in excess of legal speeds or at inappropriate speeds; driving while under the influence of alcohol, while sleepy or fatigued; or driving without using protective equipment for vehicle occupants. There are currently very few SA interventions that specifically target this important industry role-player. The Safe Travel to School Programme was recently implemented by a national child safety agency, with a focus on driver road safety awareness, defensive driver training, eye- testing, vehicle roadworthy inspections with selected upgrades, incentives for safe performance, and implementation of a vehicle telematics tracking system with regular, individual driving behaviour information updates. This quasi-experimental study offers an evaluation of the initial impact on safety performance of this telematics-based driver and vehicle safety intervention in terms of speeding, acceleration, braking, cornering, and time-of-day driving, and compares the school transport driver performance with that of general motorists. Despite concerns that some school transport vehicles are used for multiple purposes outside of school transport duties, at night, and for longer distances, overall these vehicles recorded lower percentages of speeding, lower harsh braking, and lower average harsh cornering and acceleration than general drivers.

Peer influence predicts speeding prevalence among teenage drivers.

Science.gov (United States)

Simons-Morton, Bruce G; Ouimet, Marie Claude; Chen, Rusan; Klauer, Sheila G; Lee, Suzanne E; Wang, Jing; Dingus, Thomas A

2012-12-01

Preventing speed-related crashes could reduce costs and improve efficiency in the transportation industry. This research examined the psychosocial and personality predictors of observed speeding among young drivers. Survey and driving data were collected from 42 newly-licensed teenage drivers during the first 18months of licensure. Speeding (i.e., driving 10mph over the speed limit; about 16km/h) was assessed by comparing speed data collected with recording systems installed in participants' vehicles with posted speed limits. Speeding was correlated with elevated g-force event rates (r=0.335, pb0.05), increased over time, and predicted by day vs. night trips, higher sensation seeking, substance use, tolerance of deviance, susceptibility to peer pressure, and number of risky friends. Perceived risk was a significant mediator of the association between speeding and risky friends. The findings support the contention that social norms may influence teenage speeding behavior and this relationship may operate through perceived risk. Copyright © 2012 National Safety Council and Elsevier Ltd. All rights reserved.

Towards a real-time driver workload estimator: An on-the-road study

NARCIS (Netherlands)

Leeuwen, P. van; Landman, R.; Buning, L.; Heffelaar, T.; Hogema, J.; Hemert, J.M. van; Winter, J. de; Happee, R.

2017-01-01

Driver distraction is a leading cause of crashes. The introduction of in-vehicle technology in the last decades has added support to the driving task. However, in-vehicle technologies and handheld electronic devices may also be a threat to driver safety due to information overload and distraction.

Survey of pedestrian detection for advanced driver assistance systems.

Science.gov (United States)

Gerónimo, David; López, Antonio M; Sappa, Angel D; Graf, Thorsten

2010-07-01

Advanced driver assistance systems (ADASs), and particularly pedestrian protection systems (PPSs), have become an active research area aimed at improving traffic safety. The major challenge of PPSs is the development of reliable on-board pedestrian detection systems. Due to the varying appearance of pedestrians (e.g., different clothes, changing size, aspect ratio, and dynamic shape) and the unstructured environment, it is very difficult to cope with the demanded robustness of this kind of system. Two problems arising in this research area are the lack of public benchmarks and the difficulty in reproducing many of the proposed methods, which makes it difficult to compare the approaches. As a result, surveying the literature by enumerating the proposals one--after-another is not the most useful way to provide a comparative point of view. Accordingly, we present a more convenient strategy to survey the different approaches. We divide the problem of detecting pedestrians from images into different processing steps, each with attached responsibilities. Then, the different proposed methods are analyzed and classified with respect to each processing stage, favoring a comparative viewpoint. Finally, discussion of the important topics is presented, putting special emphasis on the future needs and challenges.

Designing driver assistance systems with crossmodal signals: multisensory integration rules for saccadic reaction times apply.

Directory of Open Access Journals (Sweden)

Rike Steenken

Full Text Available Modern driver assistance systems make increasing use of auditory and tactile signals in order to reduce the driver's visual information load. This entails potential crossmodal interaction effects that need to be taken into account in designing an optimal system. Here we show that saccadic reaction times to visual targets (cockpit or outside mirror, presented in a driving simulator environment and accompanied by auditory or tactile accessories, follow some well-known spatiotemporal rules of multisensory integration, usually found under confined laboratory conditions. Auditory nontargets speed up reaction time by about 80 ms. The effect tends to be maximal when the nontarget is presented 50 ms before the target and when target and nontarget are spatially coincident. The effect of a tactile nontarget (vibrating steering wheel was less pronounced and not spatially specific. It is shown that the average reaction times are well-described by the stochastic "time window of integration" model for multisensory integration developed by the authors. This two-stage model postulates that crossmodal interaction occurs only if the peripheral processes from the different sensory modalities terminate within a fixed temporal interval, and that the amount of crossmodal interaction manifests itself in an increase or decrease of second stage processing time. A qualitative test is consistent with the model prediction that the probability of interaction, but not the amount of crossmodal interaction, depends on target-nontarget onset asynchrony. A quantitative model fit yields estimates of individual participants' parameters, including the size of the time window. Some consequences for the design of driver assistance systems are discussed.

Planning Support Systems (PSS-Based Spatial Plan Alternatives and Environmental Assessment

Directory of Open Access Journals (Sweden)

Hee-Sun Choi

2016-03-01

Full Text Available Spatial planning is at the core of national land and urban development. Many countries and cities seek sustainable development through various means such as coordinated environmental planning, environmental assessment, and internalization of environmental analysis and planning. A Planning Support System (PSS is a GIS (Geographic Information System-based, spatial decision-making support system that incorporates a variety of theories and pertinent models. This study adopted the “What if?” model to design an alternative spatial plan that includes generation of predictive scenarios and is relatively easy to use. In the cities studied, we identified a total of six scenarios based on the main drivers of development—namely, population and spatial policies. Subsequently, we assessed the alternatives for their environmental impact, preparing sensitivity maps for each major environmental issue in the target area (natural ecosystem, air and microclimate, natural disasters. One projected advantage of the “What if?” model is that its digital visualization of proposed plans may improve public awareness and involvement. Furthermore, the tool is expected to be highly useful in ensuring the objectivity of quantitative analyses. However, it is necessary to develop a PSS that is both standardized and tailored to the particular needs of each area. Finally, the development of an e-governance system will be beneficial in ensuring public access to the decision making process.

Driver's behavioural changes with new intelligent transport system interventions at railway level crossings--A driving simulator study.

Science.gov (United States)

Larue, Grégoire S; Kim, Inhi; Rakotonirainy, Andry; Haworth, Narelle L; Ferreira, Luis

2015-08-01

Improving safety at railway level crossings is an important issue for the Australian transport system. Governments, the rail industry and road organisations have tried a variety of countermeasures for many years to improve railway level crossing safety. New types of intelligent transport system (ITS) interventions are now emerging due to the availability and the affordability of technology. These interventions target both actively and passively protected railway level crossings and attempt to address drivers' errors at railway crossings, which are mainly a failure to detect the crossing or the train and misjudgement of the train approach speed and distance. This study aims to assess the effectiveness of three emerging ITS that the rail industry considers implementing in Australia: a visual in-vehicle ITS, an audio in-vehicle ITS, as well as an on-road flashing beacons intervention. The evaluation was conducted on an advanced driving simulator with 20 participants per trialled technology, each participant driving once without any technology and once with one of the ITS interventions. Every participant drove through a range of active and passive crossings with and without trains approaching. Their speed approach of the crossing, head movements and stopping compliance were measured. Results showed that driver behaviour was changed with the three ITS interventions at passive crossings, while limited effects were found at active crossings, even with reduced visibility. The on-road intervention trialled was unsuccessful in improving driver behaviour; the audio and visual ITS improved driver behaviour when a train was approaching. A trend toward worsening driver behaviour with the visual ITS was observed when no trains were approaching. This trend was not observed for the audio ITS intervention, which appears to be the ITS intervention with the highest potential for improving safety at passive crossings. Copyright © 2015 Elsevier Ltd. All rights reserved.

Concurrent audio-visual feedback for supporting drivers at intersections: A study using two linked driving simulators.

Science.gov (United States)

Houtenbos, M; de Winter, J C F; Hale, A R; Wieringa, P A; Hagenzieker, M P

2017-04-01

A large portion of road traffic crashes occur at intersections for the reason that drivers lack necessary visual information. This research examined the effects of an audio-visual display that provides real-time sonification and visualization of the speed and direction of another car approaching the crossroads on an intersecting road. The location of red blinking lights (left vs. right on the speedometer) and the lateral input direction of beeps (left vs. right ear in headphones) corresponded to the direction from where the other car approached, and the blink and beep rates were a function of the approaching car's speed. Two driving simulators were linked so that the participant and the experimenter drove in the same virtual world. Participants (N = 25) completed four sessions (two with the audio-visual display on, two with the audio-visual display off), each session consisting of 22 intersections at which the experimenter approached from the left or right and either maintained speed or slowed down. Compared to driving with the display off, the audio-visual display resulted in enhanced traffic efficiency (i.e., greater mean speed, less coasting) while not compromising safety (i.e., the time gap between the two vehicles was equivalent). A post-experiment questionnaire showed that the beeps were regarded as more useful than the lights. It is argued that the audio-visual display is a promising means of supporting drivers until fully automated driving is technically feasible. Copyright © 2016. Published by Elsevier Ltd.

Drivers of land use change and household determinants of sustainability in smallholder farming systems of Eastern Uganda

NARCIS (Netherlands)

Ebanyat, P.; Ridder, de N.; Jager, de A.; Delve, R.J.; Bekunda, M.; Giller, K.E.

2010-01-01

Smallholder farming systems in sub-Saharan Africa have undergone changes in land use, productivity and sustainability. Understanding of the drivers that have led to changes in land use in these systems and factors that influence the systems’ sustainability is useful to guide appropriate targeting of

The development of ground unmanned vehicles, driver assistance systems and components according to patent publications

Science.gov (United States)

Saykin, A. M.; Tuktakiev, G. S.; Zhuravlev, A. V.; Zaitseva, E. P.

2018-02-01

The paper contains the analysis of the main trends in the patenting of ground unmanned vehicles, driver assistance systems (ADAS) and unmanned vehicle components abroad during the period from 2010 to 2016. The conclusion was made that the intensity of their patenting abroad increased.

a Design of the Driver Airbag Module with Floating Horn Assembly

Science.gov (United States)

Suh, Chang-Min; Lee, Young-Hoon; Suh, Duck-Young

The driver airbag system is designed as a supplemental restraint system in addition to the seatbelt, and is designed to protect the driver's head and chest against severe injury by a device that is actuated in case of vehicle's fronted impact. Deployment of an airbag module with floating horn assembly is a highly dynamic process. The concept of driver airbag module with floating horn assembly and aluminum emblem is presented as a useful parameter when the airbag deploys and the energy is evaluated as performance factor in airbag module. Floating horn assembly is also one of the major factors for driver airbag module design to perform its horn function and check the package between driver airbag module and steering wheel. This study on the design of driver airbag module with floating horn assembly proved the feasibility as a new safety device. However, the system level study is needed for decrease of passenger injury. This study can be used for the implementation of a prototype of DABM with floating horn device.

Free Electron Laser as Energy Driver for Inertial Confinement Fusion

International Nuclear Information System (INIS)

Saldin, E.L.; Shnejdmiller, E.A.; Ul'yanov, Yu.N.; Sarantsev, V.P.; Yurkov, M.V.

1994-01-01

A FEL based energy driver for Inertial Confinement Fusion (ICF) is proposed. The key element of the scheme is free electron laser system. Novel technical solutions reveal a possibility to construct the FEL system operating at radiation wavelength λ = 0.5 μm and providing flash energy E = 1 MJ and brightness 4 x 10 22 W cm -2 sr -1 within steering pulse duration 0.1-2 ns. Total energy efficiency of the proposed ICF energy driver is about of 11% and repetition rate is 40 Hz. Dimensions of such an ICF driver are comparable with those of heavy-ion ICF driver, while the problem of technical realization seems to be more realistic. It is shown that the FEL based ICF energy driver may be constructed at the present level of accelerator technique R and D. 27 refs., 10 figs., 3 tabs

Performance assessment of an onboard monitoring system for CMV drivers : a field operational test : research brief.

Science.gov (United States)

2016-11-01

The primary goal of an onboard monitoring system (OBMS) is to enhance driver performance and safety. OBMSs are employed with the expectation that feedback provided concurrently (via flashing feedback lights in the vehicle) and cumulatively (via coach...

Predicting crash-relevant violations at stop sign-controlled intersections for the development of an intersection driver assistance system.

Science.gov (United States)

Scanlon, John M; Sherony, Rini; Gabler, Hampton C

2016-09-01

Intersection crashes resulted in over 5,000 fatalities in the United States in 2014. Intersection Advanced Driver Assistance Systems (I-ADAS) are active safety systems that seek to help drivers safely traverse intersections. I-ADAS uses onboard sensors to detect oncoming vehicles and, in the event of an imminent crash, can either alert the driver or take autonomous evasive action. The objective of this study was to develop and evaluate a predictive model for detecting whether a stop sign violation was imminent. Passenger vehicle intersection approaches were extracted from a data set of typical driver behavior (100-Car Naturalistic Driving Study) and violations (event data recorders downloaded from real-world crashes) and were assigned weighting factors based on real-world frequency. A k-fold cross-validation procedure was then used to develop and evaluate 3 hypothetical stop sign warning algorithms (i.e., early, intermediate, and delayed) for detecting an impending violation during the intersection approach. Violation detection models were developed using logistic regression models that evaluate likelihood of a violation at various locations along the intersection approach. Two potential indicators of driver intent to stop-that is, required deceleration parameter (RDP) and brake application-were used to develop the predictive models. The earliest violation detection opportunity was then evaluated for each detection algorithm in order to (1) evaluate the violation detection accuracy and (2) compare braking demand versus maximum braking capabilities. A total of 38 violating and 658 nonviolating approaches were used in the analysis. All 3 algorithms were able to detect a violation at some point during the intersection approach. The early detection algorithm, as designed, was able to detect violations earlier than all other algorithms during the intersection approach but gave false alarms for 22.3% of approaches. In contrast, the delayed detection algorithm sacrificed

Neurological symptoms and syndromes in municipal transport drivers

Directory of Open Access Journals (Sweden)

Halina Sińczuk-Walczak

2015-07-01

Full Text Available Background: The way the municipal transport drivers perform their job contributes to varied burdens linked with the body posture at work, stress, shift work, vibration, noise and exposure to chemical agents. The aim of the study was to assess the condition of the nervous system (NS in municipal transport drivers. Material and Methods: The study covered 42 men, aged 43.4 years (standard deviation (SD: 8.3, employed as bus drivers in the municipal transport enterprise. The duration of employment was 11.8 years on average (SD: 8.6. The condition of the nervous system was assessed on the basis of clinical neurological examinations. Results: Chronic lumbosacral syndrome was found in 54.8% of the subjects. A significant relationship between the incidence of lumbosacral syndrome and the duration of employment (p = 0.032 was observed; significantly higher in drivers employed for 11–15 years (90.9% in comparison to the remaining groups. Nervous system functional disorders were niejedcharacterized by the increased emotional irritability (47.6%, sleep disorders manifested by excessive sleepiness (33.3% or insomnia (28.6% and headaches (3%, mostly tension headaches. Excessive daytime sleepiness was significantly age-dependent (p = 0.038. Conclusions: The evidenced NS disorders indicate the need to undertake preventive measures tailored for the occupational group of bus drivers. Med Pr 2015;66(3:333–341

Gaze position modulates the effectiveness of forward collision warnings for drowsy drivers.

Science.gov (United States)

Gaspar, John G; Schwarz, John-Chris W; Brown, Timothy L; Kang, Julie

2017-12-22

Advanced driver assistance systems (ADAS) have the potential to prevent crashes and reduce their severity. Forward collision warnings (FCW) are quickly becoming standard across vehicle lineups and may prevent frontal crashes by alerting drivers. Previous research has demonstrated the effectiveness of FCW for distracted drivers, but their effectiveness for other types of impairment remains unknown. Like distraction, drowsiness can impair driver response time and lead to crashes. The goal of the present study was to evaluate the effectiveness of FCW for moderately and severely drowsy drivers using a high-fidelity driving simulator. Drowsy drivers were divided into three warning conditions during a revealed stop vehicle forward collision event: An auditory alert, a haptic seat vibration, and a no warning baseline. Results indicate that FCW were effective at speeding drowsy driver response, but only when the drowsy drivers were looking away from the forward roadway at the onset of the event. These results have important implications for ADAS technology and driver state monitoring systems. Copyright © 2017 Elsevier Ltd. All rights reserved.

Do advertisements at the roadside distract the driver?

Science.gov (United States)

Kettwich, Carmen; Klinger, Karsten; Lemmer, Uli

2008-04-01

Nowadays drivers have to get along with an increasing complex visual environment. More and more cars are on the road. There are not only distractions available within the vehicle, like radio and navigation system, the environment outside the car has also become more and more complex. Hoardings, advertising pillars, shop fronts and video screens are just a few examples. For this reason the potential risk of driver distraction is rising. But in which way do the advertisements at the roadside influence the driver's attention? The investigation which is described is devoted to this topic. Various kinds of advertisements played an important role, like illuminated and non-illuminated posters as well as illuminated animated ads. Several test runs in an urban environment were performed. The gaze direction of the driver's eye was measured with an eye tracking system. The latter consists of three cameras which logged the eye movements during the test run and a small-sized scene camera recording the traffic scene. 16 subjects (six female and ten male) between 21 and 65 years of age took part in this experiment. Thus the driver's fixation duration of the different advertisements could be determined.

[Reliability and validity of Driving Anger Scale in professional drivers in China].

Science.gov (United States)

Li, Z; Yang, Y M; Zhang, C; Li, Y; Hu, J; Gao, L W; Zhou, Y X; Zhang, X J

2017-11-10

Objective: To assess the reliability and validity of the Chinese version of Driving Anger Scale (DAS) in professional drivers in China and provide a scientific basis for the application of the scale in drivers in China. Methods: Professional drivers, including taxi drivers, bus drivers, truck drivers and school bus drivers, were selected to complete the questionnaire. Cronbach's α and split-half reliability were calculated to evaluate the reliability of DAS, and content, contract, discriminant and convergent validity were performed to measure the validity of the scale. Results: The overall Cronbach's α of DAS was 0.934 and the split-half reliability was 0.874. The correlation coefficient of each subscale with the total scale was 0.639-0.922. The simplified version of DAS supported a presupposed six-factor structure, explaining 56.371% of the total variance revealed by exploratory factor analysis. The DAS had good convergent and discriminant validity, with the success rate of calibration experiment of 100%. Conclusion: DAS has a good reliability and validity in professional drivers in China, and the use of DAS is worth promoting in divers.

Driver style and driver skill – Clustering sub-groups of drivers differing in their potential danger in traffic

DEFF Research Database (Denmark)

Martinussen, Laila Marianne; Møller, Mette; Prato, Carlo Giacomo

The Driver Behavior Questionnaire (DBQ) and the Driver Skill Inventory (DSI) are two of the most frequently used measures of self-reported driving style and driving skill. The motivation behind the present study was to test drivers’ consistency or judgment of their own self-reported driving ability...... based on a combined use of the DBQ and the DSI. Moreover, the joint use of the two instruments was applied to identify sub-groups of drivers that differ in their potential danger in traffic (as measured by frequency of aberrant driving behaviors and level of driving skills), as well as to test whether...... the sub-groups of drivers differed in characteristics such as age, gender, annual mileage and accident involvement. 3908 drivers aged 18–84 participated in the survey. The results suggested that the drivers are consistent in their reporting of driving ability, as the self-reported driving skill level...

Review on identification study of driver behavior intention and characteristics

Directory of Open Access Journals (Sweden)

Gang LI

2017-08-01

Full Text Available In order to better improve vehicle active safety and realize personalized driving, aiming at the problem of the identification of driver behavior intention and characteristics, the electronic control systems' important role in the automobile and the importance of the driver behavior intention and characteristic identification are discussed. The relative domestic and foreign research is summarized, and the prospect is put forward. In order to improve the performance of automobile electronic control system and realize the intelligent control for the cars, the identification of driver behavior intention and characteristics needs to be studied. How to rationally classify and on-line identify drivers' characteristics correctly for the steering, braking and acceleration characteristics is a long term research topic.

Driver trust in five driver assistance technologies following real-world use in four production vehicles.

Science.gov (United States)

Kidd, David G; Cicchino, Jessica B; Reagan, Ian J; Kerfoot, Laura B

2017-05-29

Information about drivers' experiences with driver assistance technologies in real driving conditions is sparse. This study characterized driver interactions with forward collision warning, adaptive cruise control, active lane keeping, side-view assist, and lane departure warning systems following real-world use. Fifty-four Insurance Institute for Highway Safety employees participated and drove a 2016 Toyota Prius, 2016 Honda Civic, 2017 Audi Q7, or 2016 Infiniti QX60 for up to several weeks. Participants reported mileage and warnings from the technologies in an online daily-use survey. Participants reported their level of agreement with five statements regarding trust in an online post-use survey. Responses were averaged to create a composite measure of trust ranging from -2 (strongly disagree) to +2 (strongly agree) for each technology. Mixed-effect regression models were constructed to compare trust among technologies and separately among the study vehicles. Participants' free-response answers about what they liked least about each system were coded and examined. Participants reported driving 33,584 miles during 4 months of data collection. At least one forward collision warning was reported in 26% of the 354 daily reports. The proportion of daily reports indicating a forward collision warning was much larger for the Honda (70%) than for the Audi (18%), Infiniti (15%), and Toyota (10%). Trust was highest for side-view assist (0.98) and lowest for active lane keeping (0.20). Trust in side-view assist was significantly higher than trust in active lane keeping and lane departure warning (0.53). Trust in active lane keeping was significantly lower than trust in adaptive cruise control (0.67) and forward collision warning (0.71). Trust in adaptive cruise control was higher for the Audi (0.72) and Toyota (0.75) compared with the Honda (0.30), and significantly higher for the Infiniti (0.93). Trust in Infiniti's side-view assist (0.58) was significantly lower than

Deep Learning-Based Gaze Detection System for Automobile Drivers Using a NIR Camera Sensor

Directory of Open Access Journals (Sweden)

Rizwan Ali Naqvi

2018-02-01

Full Text Available A paradigm shift is required to prevent the increasing automobile accident deaths that are mostly due to the inattentive behavior of drivers. Knowledge of gaze region can provide valuable information regarding a driver’s point of attention. Accurate and inexpensive gaze classification systems in cars can improve safe driving. However, monitoring real-time driving behaviors and conditions presents some challenges: dizziness due to long drives, extreme lighting variations, glasses reflections, and occlusions. Past studies on gaze detection in cars have been chiefly based on head movements. The margin of error in gaze detection increases when drivers gaze at objects by moving their eyes without moving their heads. To solve this problem, a pupil center corneal reflection (PCCR-based method has been considered. However, the error of accurately detecting the pupil center and corneal reflection center is increased in a car environment due to various environment light changes, reflections on glasses surface, and motion and optical blurring of captured eye image. In addition, existing PCCR-based methods require initial user calibration, which is difficult to perform in a car environment. To address this issue, we propose a deep learning-based gaze detection method using a near-infrared (NIR camera sensor considering driver head and eye movement that does not require any initial user calibration. The proposed system is evaluated on our self-constructed database as well as on open Columbia gaze dataset (CAVE-DB. The proposed method demonstrated greater accuracy than the previous gaze classification methods.

Drivers and moderators of business decline

Directory of Open Access Journals (Sweden)

Marius Pretorius

2010-12-01

Full Text Available Purpose: Reports of business failure elicit various reactions, while research in this domain often appears to be limited by a lack of access to information about failure and by the negativity that surrounds it. Those who have experienced failure do not readily talk about it, or they disappear from the radar screen of researchers. Yet failure is preceded by decline which, when focused on strategically, can reduce eventual failures if early action is taken. The main purpose of this study is to develop a conceptual framework or typology of the drivers and moderators of business decline. Design/methodology/approach: After applying the "grounded theory" approach to the academic literature on decline and failure, a conceptual framework for the variables that drive and moderate business decline is proposed. Findings: The study proposes that decline has three core drivers, three peripheral drivers and four moderators. The core drivers identified are: resource munificence; leadership as origin; and causality (strategic versus operational origin of decline. The three peripheral drivers are: unique preconditions; continuous decisions impact; and extremes dichotomy. The study describes four moderators of the drivers: life cycle stage; stakeholder perspective; quantitative versus qualitative nature of signs and causes; and finally the age and size effects. Research limitations/implications: The proposed conceptual framework is based on literature only, although it has found support during discussions with practitioners. It is proposed to readers of this journal for scrutiny and validation. Practical implications: Strategists need to understand what drives decline in order to act timeously; practitioners who have an insight into the moderators with their impacts could make better decisions in response to decline in organisations and possibly avoid business failure. Originality/Value: Understanding business decline is still a huge theoretical challenge, which

Determinants and Drivers of Infectious Disease Threat Events in Europe.

Science.gov (United States)

Semenza, Jan C; Lindgren, Elisabet; Balkanyi, Laszlo; Espinosa, Laura; Almqvist, My S; Penttinen, Pasi; Rocklöv, Joacim

2016-04-01

Infectious disease threat events (IDTEs) are increasing in frequency worldwide. We analyzed underlying drivers of 116 IDTEs detected in Europe during 2008-2013 by epidemic intelligence at the European Centre of Disease Prevention and Control. Seventeen drivers were identified and categorized into 3 groups: globalization and environment, sociodemographic, and public health systems. A combination of >2 drivers was responsible for most IDTEs. The driver category globalization and environment contributed to 61% of individual IDTEs, and the top 5 individual drivers of all IDTEs were travel and tourism, food and water quality, natural environment, global trade, and climate. Hierarchical cluster analysis of all drivers identified travel and tourism as a distinctly separate driver. Monitoring and modeling such disease drivers can help anticipate future IDTEs and strengthen control measures. More important, intervening directly on these underlying drivers can diminish the likelihood of the occurrence of an IDTE and reduce the associated human and economic costs.

Exploring Challenges in Developing a Smart and Effective Assistive System for Improving the Experience of the Elderly Drivers

Science.gov (United States)

Jung, Sebin; Meng, Hong-Ying; Qin, Sheng-Feng

2017-09-01

As the overall population ages, driving-related accidents and injuries, associated with elderly drivers, have risen. Existing research about elderly drivers mainly focuses on factual data collection and analysis, indicating the elderly's growing fatal accident rates and their different behaviours compared to younger drivers. However, few research has focused on design-led practical solutions to mitigate the elderly's growing fatal accidents, by considering their usability and body conditions, afflicting the elderly, such as decreased vision, hearing, and reaction times. In this paper, first, current worldwide situations on growing fatal accident rates for elderly drivers is reviewed and the key impact factors are identified and discussed with regarding to usability and design trend in the automotive technology for elderly. Second, existing smart vehicle technology-based solutions to promote safe driving are explored and their pros and cons are discussed and analysed. Most of solutions are not created by people with driving difficulties, which are caused by health problems most commonly afflicting the elderly. Thirdly, diverse design-led research activities are taken, such as a survey, observation, and interviews to gain new understanding of what kinds of driving problems elderly drivers have and demonstrate how new system concepts could be developed for the elderly's benefits. Finally, it is found that the elderly's low vision and late reaction are main factors causing their driving difficulties. Based on this finding, usable vehicle system design ideas have been proposed, by utilising facial expression sensing technology as a solution. The proposed solutions would ensure reducing both the elderly's driving problems and high fatal accident rates and provide a more enjoyable driving environment for the elderly population.

An econometric analysis of the effects of the penalty points system driver's license in Spain.

Science.gov (United States)

Castillo-Manzano, José I; Castro-Nuño, Mercedes; Pedregal, Diego J

2010-07-01

This article seeks to quantify the effects of the penalty points system driver's license during the 18-month period following its coming into force. This is achieved by means of univariate and multivariate unobserved component models set up in a state space framework estimated using maximum likelihood. A detailed intervention analysis is carried out in order to test for the effects and their duration of the introduction of the penalty points system driver's license in Spain. Other variables, mainly indicators of the level of economic activity in Spain, are also considered. Among the main effects, we can mention an average reduction of almost 12.6% in the number of deaths in highway accidents. It would take at least 2 years for that effect to disappear. For the rest of the safety indicator variables (vehicle occupants injured in highway accidents and vehicle occupants injured in accidents built-up areas) the effects disappeared 1 year after the law coming into force. Copyright 2010 Elsevier Ltd. All rights reserved.

SPADAS: a high-speed 3D single-photon camera for advanced driver assistance systems

Science.gov (United States)

Bronzi, D.; Zou, Y.; Bellisai, S.; Villa, F.; Tisa, S.; Tosi, A.; Zappa, F.

2015-02-01

Advanced Driver Assistance Systems (ADAS) are the most advanced technologies to fight road accidents. Within ADAS, an important role is played by radar- and lidar-based sensors, which are mostly employed for collision avoidance and adaptive cruise control. Nonetheless, they have a narrow field-of-view and a limited ability to detect and differentiate objects. Standard camera-based technologies (e.g. stereovision) could balance these weaknesses, but they are currently not able to fulfill all automotive requirements (distance range, accuracy, acquisition speed, and frame-rate). To this purpose, we developed an automotive-oriented CMOS single-photon camera for optical 3D ranging based on indirect time-of-flight (iTOF) measurements. Imagers based on Single-photon avalanche diode (SPAD) arrays offer higher sensitivity with respect to CCD/CMOS rangefinders, have inherent better time resolution, higher accuracy and better linearity. Moreover, iTOF requires neither high bandwidth electronics nor short-pulsed lasers, hence allowing the development of cost-effective systems. The CMOS SPAD sensor is based on 64 × 32 pixels, each able to process both 2D intensity-data and 3D depth-ranging information, with background suppression. Pixel-level memories allow fully parallel imaging and prevents motion artefacts (skew, wobble, motion blur) and partial exposure effects, which otherwise would hinder the detection of fast moving objects. The camera is housed in an aluminum case supporting a 12 mm F/1.4 C-mount imaging lens, with a 40°×20° field-of-view. The whole system is very rugged and compact and a perfect solution for vehicle's cockpit, with dimensions of 80 mm × 45 mm × 70 mm, and less that 1 W consumption. To provide the required optical power (1.5 W, eye safe) and to allow fast (up to 25 MHz) modulation of the active illumination, we developed a modular laser source, based on five laser driver cards, with three 808 nm lasers each. We present the full characterization of

Improving Driver Alertness through Music Selection Using a Mobile EEG to Detect Brainwaves

Directory of Open Access Journals (Sweden)

Hsiang-Ming Hsu

2013-06-01

Full Text Available Driving safety has become a global topic of discussion with the recent development of the Smart Car concept. Many of the current car safety monitoring systems are based on image discrimination techniques, such as sensing the vehicle drifting from the main road, or changes in the driver’s facial expressions. However, these techniques are either too simplistic or have a low success rate as image processing is easily affected by external factors, such as weather and illumination. We developed a drowsiness detection mechanism based on an electroencephalogram (EEG reading collected from the driver with an off-the-shelf mobile sensor. This sensor employs wireless transmission technology and is suitable for wear by the driver of a vehicle. The following classification techniques were incorporated: Artificial Neural Networks, Support Vector Machine, and k Nearest Neighbor. These classifiers were integrated with integration functions after a genetic algorithm was first used to adjust the weighting for each classifier in the integration function. In addition, since past studies have shown effects of music on a person’s state-of-mind, we propose a personalized music recommendation mechanism as a part of our system. Through the in-car stereo system, this music recommendation mechanism can help prevent a driver from becoming drowsy due to monotonous road conditions. Experimental results demonstrate the effectiveness of our proposed drowsiness detection method to determine a driver’s state of mind, and the music recommendation system is therefore able to reduce drowsiness.

Socio-demographic impacts on lane-changing response time and distance in work zone with Drivers' Smart Advisory System

Directory of Open Access Journals (Sweden)

Qing Li

2015-10-01

Full Text Available Lane-changing behavior is an important component of traffic simulation. A lane-changing action is normally confined to a decision-making process of the task, and the action itself is sometimes assumed as an instantaneous event. Besides, the lane-changing behavior is based mostly on observable positions and speeds of other vehicles, rather than on vehicles' intentions. In practice, changing one lane requires about 5–6 s to complete. Existing lane-changing models do not comprehensively consider drivers' response to work zone lane-changing signs (or other related messages, if any. Furthermore, drivers' socio-demographics are normally not taken into account. With regard to this, fuzzy logic-based lane-changing models that consider drivers' socio-demographics were developed to improve the realism of lane-changing maneuvers in work zones. Drivers' Smart Advisory System (DSAS messages were provided as one of the scenarios. Drivers' responses, including reactions to work zone signs and DSAS messages, and actions to change lane, were investigated. Drivers' socio-demographic factors were primary independent variables, while Lane-Changing Response Time (LCRT and Distance (LCRD were defined as output variables. The model validation process yielded acceptable error ranges. To illustrate how these models can be used in traffic simulation, the LCRT and LCRD in work zones were estimated for five geo-locations with different socio-demographic specifications. Results show that the DSAS is able to instruct all drivers to prepare and change lanes earlier, thereby shortening the duration of changing lanes. Educational background and age are essential variables, whereas the impacts of gender on the output variables are indistinctive.

A Rapid Prototyping Environment for Cooperative Advanced Driver Assistance Systems

Directory of Open Access Journals (Sweden)

Kay Massow

2018-01-01

Full Text Available Advanced Driver Assistance Systems (ADAS were strong innovation drivers in recent years, towards the enhancement of traffic safety and efficiency. Today’s ADAS adopt an autonomous approach with all instrumentation and intelligence on board of one vehicle. However, to further enhance their benefit, ADAS need to cooperate in the future, using communication technologies. The resulting combination of vehicle automation and cooperation, for instance, enables solving hazardous situations by a coordinated safety intervention on multiple vehicles at the same point in time. Since the complexity of such cooperative ADAS grows with each vehicle involved, very large parameter spaces need to be regarded during their development, which necessitate novel development approaches. In this paper, we present an environment for rapidly prototyping cooperative ADAS based on vehicle simulation. Its underlying approach is either to bring ideas for cooperative ADAS through the prototyping stage towards plausible candidates for further development or to discard them as quickly as possible. This is enabled by an iterative process of refining and assessment. We reconcile the aspects of automation and cooperation in simulation by a tradeoff between precision and scalability. Reducing precise mapping of vehicle dynamics below the limits of driving dynamics enables simulating multiple vehicles at the same time. In order to validate this precision, we also present a method to validate the vehicle dynamics in simulation against real world vehicles.

An evidence-based review: distracted driver.

Science.gov (United States)

Llerena, Luis E; Aronow, Kathy V; Macleod, Jana; Bard, Michael; Salzman, Steven; Greene, Wendy; Haider, Adil; Schupper, Alex

2015-01-01

Cell phone use and texting are prevalent within society and have thus pervaded the driving population. This technology is a growing concern within the confines of distracted driving, as all diversions from attention to the road have been shown to increase the risk of crashes. Adolescent, inexperienced drivers, who have the greatest prevalence of texting while driving, are at a particularly higher risk of crashes because of distraction. Members of the Injury Control Violence Prevention Committee of the Eastern Association for the Surgery of Trauma performed a PubMed search of articles related to distracted driving and cell phone use as a distractor of driving between 2000 and 2013. A total of 19 articles were found to merit inclusion as evidence in the evidence-based review. These articles provided evidence regarding the relationship between distracted driving and crashes, cell phone use contributing to automobile accidents, and/or the relationship between driver experience and automobile accidents. (Adjust methods/results sections to the number of articles that correctly corresponds to the number of references, as well as the methodology for reference inclusion.) Based on the evidence reviewed, we can recommend the following. All drivers should minimize all in-vehicle distractions while on the road. All drivers should not text or use any touch messaging system (including the use of social media sites such as Facebook and Twitter) while driving. Younger, inexperienced drivers should especially not use cell phones, texting, or any touch messaging system while driving because they pose an increased risk for death and injury caused by distractions while driving.

Self- and peer-assessments of ambulance drivers' driving performance

Directory of Open Access Journals (Sweden)

Anna Sundström

2012-07-01

Full Text Available The aim of the present study was to develop and examine the quality of the Ambulance Driver Self-assessment Questionnaire (ADSQ and the Ambulance Driver Peer-assessment Questionnaire (ADPQ measuring aspects of, driving performance, driving style and driving competence. In addition the ADSQ measures self-reflection and safety-attitudes. The aim of the study was also to examine ambulance drivers' self- and peer-assessments as well as to examine the accuracy of self-assessments by comparing self-assessed and peer-assessed driving performance, driving style and competence. 76 ambulance drivers employed at two ambulance stations in northern Sweden completed ADSQ and ADPQ. Item analyses were conducted to examine the psychometric properties of the items, and based on the results some revisions were made to improve the questionnaires. The revised questionnaires were functioning rather well, although some subscale demonstrated low internal consistency. Subscale inter-correlations provided support for construct validity. Self- and peer-assessments indicated safe driving performance and good driver competence, which is positive from a traffic safety perspective. A comparison of mean self- and peer-assessment ratings, controlling for age, gender and driving experience showed no significant differences, except for the subscale overtaking. This indicates that ambulance drivers' self-assessments are realistic in most areas.

Bioregenerative Life Support System Research as part of the DLR EDEN Initiative

Science.gov (United States)

Bamsey, Matthew; Schubert, Daniel; Zabel, Paul; Poulet, Lucie; Zeidler, Conrad

In 2011, the DLR Institute of Space Systems launched a research initiative called EDEN - Evolution and Design of Environmentally-closed Nutrition-Sources. The research initiative focuses on bioregenerative life support systems, especially greenhouse modules, and technologies for future crewed vehicles. The EDEN initiative comprises several projects with respect to space research, ground testing and spin-offs. In 2014, EDEN’s new laboratory officially opened. This new biological cleanroom laboratory comprises several plant growth chambers incorporating a number of novel controlled environment agriculture technologies. This laboratory will be the nucleus for a variety of plant cultivation experiments within closed environments. The utilized technologies are being advanced using the pull of space technology and include such items as stacked growth systems, PAR-specific LEDs, intracanopy lighting, aeroponic nutrient delivery systems and ion-selective nutrient sensors. The driver of maximizing biomass output per unit volume and energy has much application in future bioregenerative life support systems but can also provide benefit terrestrially. The EDEN laboratory also includes several specially constructed chambers for advancing models addressing the interaction between bioregenerative and physical-chemical life support systems. The EDEN team is presently developing designs for containerized greenhouse modules. One module is planned for deployment to the German Antarctic Station, Neumayer III. The shipping container based system will provide supplementation to the overwintering crew’s diet, provide psychological benefit while at the same time advancing the technology and operational readiness of harsh environment plant production systems. In addition to hardware development, the EDEN team has participated in several early phase designs such as for the ESA Greenhouse Module for Space System and for large-scale vertical farming. These studies often utilize the

Driver fatigue alarm based on eye detection and gaze estimation

Science.gov (United States)

Sun, Xinghua; Xu, Lu; Yang, Jingyu

2007-11-01

The driver assistant system has attracted much attention as an essential component of intelligent transportation systems. One task of driver assistant system is to prevent the drivers from fatigue. For the fatigue detection it is natural that the information about eyes should be utilized. The driver fatigue can be divided into two types, one is the sleep with eyes close and another is the sleep with eyes open. Considering that the fatigue detection is related with the prior knowledge and probabilistic statistics, the dynamic Bayesian network is used as the analysis tool to perform the reasoning of fatigue. Two kinds of experiments are performed to verify the system effectiveness, one is based on the video got from the laboratory and another is based on the video got from the real driving situation. Ten persons participate in the test and the experimental result is that, in the laboratory all the fatigue events can be detected, and in the practical vehicle the detection ratio is about 85%. Experiments show that in most of situations the proposed system works and the corresponding performance is satisfying.

Impact of Automation on Drivers' Performance in Agricultural Semi-Autonomous Vehicles.

Science.gov (United States)

Bashiri, B; Mann, D D

2015-04-01

Drivers' inadequate mental workload has been reported as one of the negative effects of driving assistant systems and in-vehicle automation. The increasing trend of automation in agricultural vehicles raises some concerns about drivers' mental workload in such vehicles. Thus, a human factors perspective is needed to identify the consequences of such automated systems. In this simulator study, the effects of vehicle steering task automation (VSTA) and implement control and monitoring task automation (ICMTA) were investigated using a tractor-air seeder system as a case study. Two performance parameters (reaction time and accuracy of actions) were measured to assess drivers' perceived mental workload. Experiments were conducted using the tractor driving simulator (TDS) located in the Agricultural Ergonomics Laboratory at the University of Manitoba. Study participants were university students with tractor driving experience. According to the results, reaction time and number of errors made by drivers both decreased as the automation level increased. Correlations were found among performance parameters and subjective mental workload reported by the drivers.

Smart driver monitoring : when signal processing meets human factors : in the driver's seat

NARCIS (Netherlands)

Aghaei, A.S.; Donmez, B.; Liu, C.C.; He, D.; Liu, G.; Plataniotis, K.N.; Chen, H.Y.W.; Sojoudi, Z.

2016-01-01

This article provides an interdisciplinary perspective on driver monitoring systems by discussing state-of-the-art signal processing solutions in the context of road safety issues identified in human factors research. Recently, the human factors community has made significant progress in

Highly automated driving, secondary task performance, and driver state.

Science.gov (United States)

Merat, Natasha; Jamson, A Hamish; Lai, Frank C H; Carsten, Oliver

2012-10-01

A driving simulator study compared the effect of changes in workload on performance in manual and highly automated driving. Changes in driver state were also observed by examining variations in blink patterns. With the addition of a greater number of advanced driver assistance systems in vehicles, the driver's role is likely to alter in the future from an operator in manual driving to a supervisor of highly automated cars. Understanding the implications of such advancements on drivers and road safety is important. A total of 50 participants were recruited for this study and drove the simulator in both manual and highly automated mode. As well as comparing the effect of adjustments in driving-related workload on performance, the effect of a secondary Twenty Questions Task was also investigated. In the absence of the secondary task, drivers' response to critical incidents was similar in manual and highly automated driving conditions. The worst performance was observed when drivers were required to regain control of driving in the automated mode while distracted by the secondary task. Blink frequency patterns were more consistent for manual than automated driving but were generally suppressed during conditions of high workload. Highly automated driving did not have a deleterious effect on driver performance, when attention was not diverted to the distracting secondary task. As the number of systems implemented in cars increases, an understanding of the implications of such automation on drivers' situation awareness, workload, and ability to remain engaged with the driving task is important.

Counterfactual simulations applied to SHRP2 crashes: The effect of driver behavior models on safety benefit estimations of intelligent safety systems.

Science.gov (United States)

Bärgman, Jonas; Boda, Christian-Nils; Dozza, Marco

2017-05-01

As the development and deployment of in-vehicle intelligent safety systems (ISS) for crash avoidance and mitigation have rapidly increased in the last decades, the need to evaluate their prospective safety benefits before introduction has never been higher. Counterfactual simulations using relevant mathematical models (for vehicle dynamics, sensors, the environment, ISS algorithms, and models of driver behavior) have been identified as having high potential. However, although most of these models are relatively mature, models of driver behavior in the critical seconds before a crash are still relatively immature. There are also large conceptual differences between different driver models. The objective of this paper is, firstly, to demonstrate the importance of the choice of driver model when counterfactual simulations are used to evaluate two ISS: Forward collision warning (FCW), and autonomous emergency braking (AEB). Secondly, the paper demonstrates how counterfactual simulations can be used to perform sensitivity analyses on parameter settings, both for driver behavior and ISS algorithms. Finally, the paper evaluates the effect of the choice of glance distribution in the driver behavior model on the safety benefit estimation. The paper uses pre-crash kinematics and driver behavior from 34 rear-end crashes from the SHRP2 naturalistic driving study for the demonstrations. The results for FCW show a large difference in the percent of avoided crashes between conceptually different models of driver behavior, while differences were small for conceptually similar models. As expected, the choice of model of driver behavior did not affect AEB benefit much. Based on our results, researchers and others who aim to evaluate ISS with the driver in the loop through counterfactual simulations should be sure to make deliberate and well-grounded choices of driver models: the choice of model matters. Copyright © 2017 Elsevier Ltd. All rights reserved.

The effect of varying levels of vehicle automation on drivers' lane changing behaviour.

Science.gov (United States)

Madigan, Ruth; Louw, Tyron; Merat, Natasha

2018-01-01

Much of the Human Factors research into vehicle automation has focused on driver responses to critical scenarios where a crash might occur. However, there is less knowledge about the effects of vehicle automation on drivers' behaviour during non-critical take-over situations, such as driver-initiated lane-changing or overtaking. The current driving simulator study, conducted as part of the EC-funded AdaptIVe project, addresses this issue. It uses a within-subjects design to compare drivers' lane-changing behaviour in conventional manual driving, partially automated driving (PAD) and conditionally automated driving (CAD). In PAD, drivers were required to re-take control from an automated driving system in order to overtake a slow moving vehicle, while in CAD, the driver used the indicator lever to initiate a system-performed overtaking manoeuvre. Results showed that while drivers' acceptance of both the PAD and CAD systems was high, they generally preferred CAD. A comparison of overtaking positions showed that drivers initiated overtaking manoeuvres slightly later in PAD than in manual driving or CAD. In addition, when compared to conventional driving, drivers had higher deviations in lane positioning and speed, along with higher lateral accelerations during lane changes following PAD. These results indicate that even in situations which are not time-critical, drivers' vehicle control after automation is degraded compared to conventional driving.

The effect of varying levels of vehicle automation on drivers' lane changing behaviour.

Directory of Open Access Journals (Sweden)

Ruth Madigan

Full Text Available Much of the Human Factors research into vehicle automation has focused on driver responses to critical scenarios where a crash might occur. However, there is less knowledge about the effects of vehicle automation on drivers' behaviour during non-critical take-over situations, such as driver-initiated lane-changing or overtaking. The current driving simulator study, conducted as part of the EC-funded AdaptIVe project, addresses this issue. It uses a within-subjects design to compare drivers' lane-changing behaviour in conventional manual driving, partially automated driving (PAD and conditionally automated driving (CAD. In PAD, drivers were required to re-take control from an automated driving system in order to overtake a slow moving vehicle, while in CAD, the driver used the indicator lever to initiate a system-performed overtaking manoeuvre. Results showed that while drivers' acceptance of both the PAD and CAD systems was high, they generally preferred CAD. A comparison of overtaking positions showed that drivers initiated overtaking manoeuvres slightly later in PAD than in manual driving or CAD. In addition, when compared to conventional driving, drivers had higher deviations in lane positioning and speed, along with higher lateral accelerations during lane changes following PAD. These results indicate that even in situations which are not time-critical, drivers' vehicle control after automation is degraded compared to conventional driving.

Sensor-Based Trajectory Generation for Advanced Driver Assistance System

Directory of Open Access Journals (Sweden)

Christopher James Shackleton

2013-03-01

Full Text Available This paper investigates the trajectory generation problem for an advanced driver assistance system that could sense the driving state of the vehicle, so that a collision free trajectory can be generated safely. Specifically, the problem of trajectory generation is solved for the safety assessment of the driving state and to manipulate the vehicle in order to avoid any possible collisions. The vehicle senses the environment so as to obtain information about other vehicles and static obstacles ahead. Vehicles may share the perception of the environment via an inter-vehicle communication system. The planning algorithm is based on a visibility graph. A lateral repulsive potential is applied to adaptively maintain a trade-off between the trajectory length and vehicle clearance, which is the greatest problem associated with visibility graphs. As opposed to adaptive roadmap approaches, the algorithm exploits the structured nature of the environment for construction of the roadmap. Furthermore, the mostly organized nature of traffic systems is exploited to obtain orientation invariance, which is another limitation of both visibility graphs and adaptive roadmaps. Simulation results show that the algorithm can successfully solve the problem for a variety of commonly found scenarios.

Driver style and driver skills – clustering drivers differing in their potential danger in traffic

DEFF Research Database (Denmark)

Martinussen, Laila Marianne; Møller, Mette; Prato, Carlo Giacomo

The Driver Behavior Questionnaire (DBQ) and the Driver Skill Inventory (DSI) are two of the most frequently used measures of driving style and driving skill. The motivation behind the present study was to test drivers’ insight into their own driving ability based on a combined use of the DBQ......, annual mileage and accident involvement. 3908 drivers aged 18–84 participated in the survey. The results suggested that the drivers have good insight into their own driving ability, as the driving skill level mirrored the frequency of aberrant driving behaviors. K-means cluster analysis revealed four...... distinct clusters that differed in the frequency of aberrant driving behavior and driving skills, as well as individual characteristics and driving related factors such as annual mileage, accident frequency and number of tickets and fines. Thus, two sub-groups were identified as more unsafe than the two...

Sensors for advanced driver assistance systems; Sensoren fuer Fahrerassistenzsysteme

Energy Technology Data Exchange (ETDEWEB)

Ritschel, W.; Wixforth, T. [Hella KGaA Hueck und Co., Lippstadt (Germany)

2004-07-01

Essential safety applications and those aimed at driver convenience (blind spot surveillance, stop and go, pre-crash, parking assistant) can be effected in vehicles with the aid of radar sensors. The radar sensors used can be differentiated in terms of the bandwidth required (narrow band or ultra-wide band) and in terms of the modulation of the transmission signal (pulse modulation or CW). Ultra-wide band systems at the moment are not eligible for admission and do not conform with the present regulations in the European Union. The sensors currently being developed at hella for production use are characterized by the fact that they cover the primary applications in motor vehicles. In these cases the transmission signals radiated lie within the valid limits currently approved within the European Union. (orig.)

Railway suicide: the psychological effects on drivers.

Science.gov (United States)

Farmer, R; Tranah, T; O'Donnell, I; Catalan, J

1992-05-01

People have jumped (or fallen) in front of trains on the London Underground system in increasing numbers throughout the twentieth century. During the past decade there have been about 100 such incidents each year, of which around 90 would involve the train driver witnessing his train strike the person on the track. Most are suicides or attempts at suicide. They represent major unexpected and violent events in the lives of the train drivers and it might be expected that some of them would respond by developing a post-traumatic stress reaction of the type identified by Horowitz (1976) or other adverse psychological reactions or both. The research reported in this paper was designed to characterize the range of responses of drivers to the experiences of killing or injuring members of the public during the course of their daily work. It was found that 16.3% of the drivers involved in incidents did develop post-traumatic stress disorder and that other diagnoses, e.g. depression and phobic states, were present in 39.5% of drivers when interviewed one month after the incident.

Reliability of drivers in urban intersections.

Science.gov (United States)

Gstalter, Herbert; Fastenmeier, Wolfgang

2010-01-01

The concept of human reliability has been widely used in industrial settings by human factors experts to optimise the person-task fit. Reliability is estimated by the probability that a task will successfully be completed by personnel in a given stage of system operation. Human Reliability Analysis (HRA) is a technique used to calculate human error probabilities as the ratio of errors committed to the number of opportunities for that error. To transfer this notion to the measurement of car driver reliability the following components are necessary: a taxonomy of driving tasks, a definition of correct behaviour in each of these tasks, a list of errors as deviations from the correct actions and an adequate observation method to register errors and opportunities for these errors. Use of the SAFE-task analysis procedure recently made it possible to derive driver errors directly from the normative analysis of behavioural requirements. Driver reliability estimates could be used to compare groups of tasks (e.g. different types of intersections with their respective regulations) as well as groups of drivers' or individual drivers' aptitudes. This approach was tested in a field study with 62 drivers of different age groups. The subjects drove an instrumented car and had to complete an urban test route, the main features of which were 18 intersections representing six different driving tasks. The subjects were accompanied by two trained observers who recorded driver errors using standardized observation sheets. Results indicate that error indices often vary between both the age group of drivers and the type of driving task. The highest error indices occurred in the non-signalised intersection tasks and the roundabout, which exactly equals the corresponding ratings of task complexity from the SAFE analysis. A comparison of age groups clearly shows the disadvantage of older drivers, whose error indices in nearly all tasks are significantly higher than those of the other groups

Schoolbus driver performance can be improved with driver training ...

African Journals Online (AJOL)

and compares the school transport driver performance with that of general motorists. Despite concerns that ... To compare Safe Travel to School Programme driver safety perfor- .... The SA government has recognised the challenges faced with.

Heavy-ion driver parametric studies and choice of a base 5 mega-joule driver design

International Nuclear Information System (INIS)

Bieri, R.; Meier, W.

1992-01-01

Parametric studies to optimize heavy-ion driver designs are described and an optimized 5 MJ driver design is described. Parametric studies are done on driver parameters including driver energy, number of beams, type of superconductor used in focusing magnets, maximum magnetic field allowed at the superconducting windings, axial quadrupole field packing fraction, ion mass, and ion charge state. All modeled drivers use the maximum beam currents allowed by the Maschke limits; driver scaling is described in a companion paper. The optimized driver described is conservative and cost effective. The base driver direct costs are only $120/Joule, and the base driver uses no recirculation, beam combination, or beam separation. The low driver cost achieved is due, in part, to the use of compact Nb 3 Sn quadrupole arrays, but results primarily from optimization over the large, multi-dimensional, parameter space available for heavy-ion drivers

Myocardial infarction in Swedish subway drivers.

Science.gov (United States)

Bigert, Carolina; Klerdal, Kristina; Hammar, Niklas; Gustavsson, Per

2007-08-01

Particulate matter in urban air is associated with the risk of myocardial infarction in the general population. Very high levels of airborne particles have been detected in the subway system of Stockholm, as well as in several other large cities. This situation has caused concern for negative health effects among subway staff. The aim of this study was to investigate whether there is an increased incidence of myocardial infarction among subway drivers. Data from a population-based case-control study of men aged 40-69 in Stockholm County in 1976-1996 were used. The study included all first events of myocardial infarction in registers of hospital discharges and deaths. The controls were selected randomly from the general population. National censuses were used for information on occupation. Altogether, 22 311 cases and 131 496 controls were included. Among these, 54 cases and 250 controls had worked as subway drivers. The relative risk of myocardial infarction among subway drivers was not increased. It was 0.92 [95% confidence interval (95% CI) 0.68-1.25] when the subway drivers were compared with other manual workers and 1.06 (95% CI 0.78-1.43) when the subway drivers were compared with all other gainfully employed men. Subgroup analyses indicated no influence on the risk of myocardial infarction from the duration of employment, latency time, or time since employment stopped. Subway drivers in Stockholm do not have a higher incidence of myocardial infarction than other employed persons.

Requirements Development Issues for Advanced Life Support Systems: Solid Waste Management

Science.gov (United States)

Levri, Julie A.; Fisher, John W.; Alazraki, Michael P.; Hogan, John A.

2002-01-01

Long duration missions pose substantial new challenges for solid waste management in Advanced Life Support (ALS) systems. These possibly include storing large volumes of waste material in a safe manner, rendering wastes stable or sterilized for extended periods of time, and/or processing wastes for recovery of vital resources. This is further complicated because future missions remain ill-defined with respect to waste stream quantity, composition and generation schedule. Without definitive knowledge of this information, development of requirements is hampered. Additionally, even if waste streams were well characterized, other operational and processing needs require clarification (e.g. resource recovery requirements, planetary protection constraints). Therefore, the development of solid waste management (SWM) subsystem requirements for long duration space missions is an inherently uncertain, complex and iterative process. The intent of this paper is to address some of the difficulties in writing requirements for missions that are not completely defined. This paper discusses an approach and motivation for ALS SWM requirements development, the characteristics of effective requirements, and the presence of those characteristics in requirements that are developed for uncertain missions. Associated drivers for life support system technological capability are also presented. A general means of requirements forecasting is discussed, including successive modification of requirements and the need to consider requirements integration among subsystems.

UWB dual burst transmit driver

Science.gov (United States)

Dallum, Gregory E [Livermore, CA; Pratt, Garth C [Discovery Bay, CA; Haugen, Peter C [Livermore, CA; Zumstein, James M [Livermore, CA; Vigars, Mark L [Livermore, CA; Romero, Carlos E [Livermore, CA

2012-04-17

A dual burst transmitter for ultra-wideband (UWB) communication systems generates a pair of precisely spaced RF bursts from a single trigger event. An input trigger pulse produces two oscillator trigger pulses, an initial pulse and a delayed pulse, in a dual trigger generator. The two oscillator trigger pulses drive a gated RF burst (power output) oscillator. A bias driver circuit gates the RF output oscillator on and off and sets the RF burst packet width. The bias driver also level shifts the drive signal to the level that is required for the RF output device.

Drivers of forests and tree-based systems for food security and nutrition

DEFF Research Database (Denmark)

Kleinschmit, Daniela; Sijapati Basnett, Bimbika; Martin, Adrian

2015-01-01

In the context of this chapter, drivers are considered to be natural or anthropogenic developments affecting forests and tree-based systems for food security and nutrition. They can improve and contribute to food security and nutrition, but they can also lead to food insecurity and malnutrition......, commercialisation of agriculture, industrialisation of forest resources, gender imbalances, conflicts, formalisation of tenure rights, rising food prices and increasing per capita income) were identified within these four categories. They affect food security and nutrition through land use and management; through...

Patient support systems

International Nuclear Information System (INIS)

Braden, A.B.; McBride, T.R.; Styblo, D.J.; Taylor, S.K.; Richey, J.B.

1979-01-01

A patient support system for use in computerized tomography (CT) is described. The system is particularly useful for CT scanning of the brain and also of the abdominal area. The support system consists of two moveable tables which may be translated into position for X-ray scanning of the patient's body and which may be translated incrementally and automatically to obtain scans at adjacent locations. For use with brain scans, the second table is replaced by a detachable restraint assembly which is described in detail. The support system is so designed that only a small volume of low density material will intercept the X-ray beam. (UK)

Evaluating Effect of Objectives, Obstacles, Drivers, Team Dynamics and Organizational Support on ICT Effectiveness by Fuzzy DEMATEL

Directory of Open Access Journals (Sweden)

Mohammad Ali Keramati

2012-12-01

Full Text Available Due to different effects of ICT on varied aspects of performing the duties in organizations, governments have been intending to use ICT in the recent years very dramatically. The significant issue to which we should pay attention is the using of ICT without directing attention towards the mutual effects of different ICT domains shall be resulted in malfunction and inefficiency of organizations in carrying out their tasks. Therefore, the present research tried to develop a systematic structure in ICT domain and analyze the various ICT domains in order to identify the penetrating and penetrated factors (cause and effect. In doing so, at the present research firstly by the usage of other researchers' results and achievements, it was attempted to specify the different ICT domains including objectives, obstacles, drivers, team dynamics and organizational support and then another elements so-called ICT effectiveness was added in order to study the effect of above-mentioned factors on ICT effectiveness. Then, standard fuzzy DEMATEL technique questionnaire was distributed among 35 persons of experts working in ICT and IT fields to gather required information and data. After gathering required data and information, they were analyzed through DEMATEL techniques in fuzzy states, respectively. The results obtained from the DEMATEL technique in fuzzy state reveal that in ICT domain, the objectives were determined as the most penetrating elements into other elements of ICT domain and the drivers were the most penetrable element in ICT domain too.

Simulator to evaluate and optimise driver assistance systems; Ein Simulator zur Bewertung und Optimierung von Fahrerassistenzsystemen

Energy Technology Data Exchange (ETDEWEB)

Locher, J. [Hella KG Hueck and Co., Paderborn (Germany); Kleinkes, M. [Hella KG Hueck and Co., Lippstadt (Germany)

2003-07-01

For a short time now, the L-LAB (Light-LABoratory), a joint research facility of Hella KG and the University of Paderborn, has had a simulator available which allows the evaluation of driver assistance systems and the optimisation of man-machine interfaces. It is an interactive night driver simulator, which can be used to visualise any type of headlamp beam pattern true to the original. A Smart is used as the input medium; image projection is via a 3-channel high-performance beamer projection system onto large screens. Alongside synthetic roads, there is also a digitalised course available, approx. 10 km long, the original of which is actually used by Hella as a proving ground. Road safety indicators can be recorded directly and indirectly. For example, obstacles which suddenly appear force drivers to apply the brakes. The stopping distance required can be interpreted as a direct indicator for safety. In addition, an eye tracking system is used to record the eye movements of the test subjects, which allows additional road safety indicators to be derived. Comparative investigations between the digitalised proving ground and reality allow validation of the simulator. This year, a comprehensive study will be made to optimise the man-machine interface in connection with infrared vision systems in vehicles. The advantages of simulation are not only in the economical implementation possibilities and control of the variables, but also the fact that properties of driver assistance systems can be evaluated which are not even technically possible yet in reality. The use of the simulator developed here is not limited to tests connected with the visibility of obstacles, however. Rather, it allows the investigation and evaluation of a large range of potential driver assistance systems. (orig.) [German] Dem L-LAB (Light-LABoratory), einer gemeinsamen Forschungseinrichtung der Universitaet Paderborn und der Firma Hella KG in Lippstadt, steht seit kurzer Zeit ein Simulator zur

Organizational Structures and Processes to Support and Sustain Effective Technical Assistance in a State-Wide Multi-Tiered System of Support Initiative

Science.gov (United States)

Morrison, Julie Q.; Russell, Christine; Dyer, Stephanie; Metcalf, Terri; Rahschulte, Rebecca L.

2014-01-01

Despite the national proliferation of technical assistance as a driver for school reform and as a model for embedded and sustained professional development, very little is known about the organizational structures and processes needed to support technical assistance. The purpose of this paper is to describe a structured needs assessment process…

Processes, Performance Drivers and ICT Tools in Human Resources Management

Directory of Open Access Journals (Sweden)

Oškrdal Václav

2011-06-01

Full Text Available This article presents an insight to processes, performance drivers and ICT tools in human resources (HR management area. On the basis of a modern approach to HR management, a set of business processes that are handled by today’s HR managers is defined. Consequently, the concept of ICT-supported performance drivers and their relevance in the area of HR management as well as the relationship between HR business processes, performance drivers and ICT tools are defined. The theoretical outcomes are further enhanced with results obtained from a survey among Czech companies. This article was written with kind courtesy of finances provided by VŠE IGA grant „IGA – 32/2010“.

Bevel gear driver and method having torque limit selection

Science.gov (United States)

Cook, Joseph S., Jr.

1994-08-01

This invention comprises a torque drive mechanism utilizing axially translatable, mutually engageable transmission members having mating crown gears, driven and driving members with a three-element drive train being biased together by resilient means or by a fluid actuator system, the apparatus being operable to transmit a precisely controlled degree of torque to a driven member. The apparatus is applicable for use in hand tools and as a replacement for impact torque drivers, torque wrenches, motorized screw drivers, or the like, wherein the applied torque must be precisely controlled or limited. The bevel torque drive includes a drive gear which is axially displaceable and rotatable within cylindrical driver housing, a rotatable intermediate gear, and an output gear. Key rotationally secures displaceable gear with respect to input shaft but permits axial movement therebetween. A thrust bearing is preferably connected to the lower end of shaft for support to reduce play and friction between shaft and a transmission joint disc during rotation of the gear train. Coaxially mounted coiled spring is footed against displaceable gear for biasing the displaceable gear toward and into engagement with the intermediate gear for driving intermediate gear and output gear. Torque control is achieved by the use of straight or spiral beveled gears which are of configurations adapted to withdraw from mutual engagement upon the torque exceeding a predetermined limit. The novel, advantageous features of the invention include the configuration of the mating, crown gear sets and the axially translatable, slidable drive gear. The mechanism is capable of transmitting a high degree of torque within a narrow, compact transmission housing. The compact size and narrow, elongated configuration of the housing is particularly applicable for use in hand tools and in multiple torque driver mechanisms in which it is necessary to drive multiple fasteners which are located in close proximity. Prior

Identification of Visual Cues and Quantification of Drivers' Perception of Proximity Risk to the Lead Vehicle in Car-Following Situations

Science.gov (United States)

Kondoh, Takayuki; Yamamura, Tomohiro; Kitazaki, Satoshi; Kuge, Nobuyuki; Boer, Erwin Roeland

Longitudinal vehicle control and/or warning technologies that operate in accordance with drivers' subjective perception of risk need to be developed for driver-support systems, if such systems are to be used fully to achieve safer, more comfortable driving. In order to accomplish this goal, it is necessary to identify the visual cues utilized by drivers in their perception of risk when closing on the vehicle ahead in a car-following situation. It is also necessary to quantify the relation between the physical parameters defining the spatial relationship to the vehicle ahead and psychological metrics with regard to the risk perceived by the driver. This paper presents the results of an empirical study on quantification and formulization of drivers' subjective perception of risk based on experiments performed with a fixed-base driving simulator at the Nissan Research Center. Experiments were carried out to investigate the subjective perception of risk relative to the headway distance and closing velocity to the vehicle ahead using the magnitude estimation method. The experimental results showed that drivers' perception of risk was strongly affected by two variables: time headway, i.e., the distance to the lead vehicle divided by the following vehicle's velocity, and time to collision, i.e., the distance to the lead vehicle divided by relative velocity. It was also found that an equation for estimating drivers' perception of risk can be formulated as the summation of the time headway inverse and the time to collision inverse and that this expression can be applied to various approaching situations. Furthermore, the validity of this equation was examined based on real-world driver behavior data measured with an instrumented vehicle.

Can We Model Driver Perceptions? An In-Situ Experiment in Real-World Conditions

Directory of Open Access Journals (Sweden)

Aly M. Tawfik, PhD

2014-06-01

Full Text Available It is clear that perceptions play a significant role in traveler decisions. Consequently, traveler perceptions are a corner stone in the feasibility of traveler information systems; for traveler information systems are only valuable if the drivers are incapable of accurately acquiring the provided information on their own, and if the provided information is relevant for the drivers' decision criteria. Accuracy of traveler perceptions has been repeatedly researched in public transportation, and has been found to vary according to different reasons. However, in spite of the clear significance of traveler perceptions, minimal effort has been put into modeling it. Almost all travel behavior models are based on traveler experiences, which are assumed to reflect traveler perceptions via the addition of some random error component. This works introduces an alternative approach: instead of adding an error component to represent driver perceptions, it proposes to model driver perceptions. This work is based on a real-world route choice experiment of a sample of 20 drivers who made more than 2,000 real-world route choices. Each of the drivers' experiences, perceptions, and choices were recorded, analyzed and cross examined. The paper demonstrates that: i driver experiences are different from driver perceptions, ii driver perceptions explain driver choices better than driver experiences, iii it is possible to model and predict driver perceptions of travel distance, time and speed.

Obstacles to engaging in young driver licensing: Perspectives of parents.

Science.gov (United States)

Naz, Sehana; Scott-Parker, Bridie

2017-02-01

Young novice drivers remain at greater risk of injury and death despite a wealth of interventions including graduated driver licensing (GDL) programs. The key to implementing safer practices inherent in GDL appears to lie with optimising the role of parents. This qualitative research explored the parent's perspectives of obstacles to engaging in the driver licensing process within a GDL program. Parents also shared advice on what they found helpful, and where relevant, recommended changes in the process to enable safer practices for young drivers. Twenty-three parents (aged 35-60 years, M=49.52, SD=8.01, 11 males) participated in semi-structured interviews regarding licensing experiences with their young driver children. The young drivers included learner (n=11), provisional (restricted/intermediate) (n=9) and open (unrestricted/full) licence drivers (n=3), ranging from 16 to 24 years (M=18.04, SD=2.21, 13 males). Content analysis revealed that most obstacles were encountered at the learner licensing phase, with the parent-reported difficult temperament of the learner driver the most prominent. Unsurprisingly, advice to other parents to be patient and remain calm featured heavily during the same phase. Anxiety from not having control of the vehicle was another obstacle at the learner phase, translating to anxieties for child safety in the early stages of provisional driving. Recommendations for the current GDL included more rigorous road rule testing, with general support for the program, professional driver training at learner and provisional stages facilitated parental engagement through the licensing phases. The findings overwhelmingly suggest a need for parents to be educated regarding their importance in, and of, the driver licensing process, and the efficacy of their instruction, content and practices. Copyright © 2016 Elsevier Ltd. All rights reserved.

A UNIX device driver for a Translink II Transputer board

International Nuclear Information System (INIS)

Wiley, J.C.

1991-01-01

A UNIX device driver for a TransLink II Transputer board is described. A complete listing of the code is presented. The device driver allows a transputer array to be used with the A/UX operating system

Negativity Bias in Dangerous Drivers.

Directory of Open Access Journals (Sweden)

Jing Chai

Full Text Available The behavioral and cognitive characteristics of dangerous drivers differ significantly from those of safe drivers. However, differences in emotional information processing have seldom been investigated. Previous studies have revealed that drivers with higher anger/anxiety trait scores are more likely to be involved in crashes and that individuals with higher anger traits exhibit stronger negativity biases when processing emotions compared with control groups. However, researchers have not explored the relationship between emotional information processing and driving behavior. In this study, we examined the emotional information processing differences between dangerous drivers and safe drivers. Thirty-eight non-professional drivers were divided into two groups according to the penalty points that they had accrued for traffic violations: 15 drivers with 6 or more points were included in the dangerous driver group, and 23 drivers with 3 or fewer points were included in the safe driver group. The emotional Stroop task was used to measure negativity biases, and both behavioral and electroencephalograph data were recorded. The behavioral results revealed stronger negativity biases in the dangerous drivers than in the safe drivers. The bias score was correlated with self-reported dangerous driving behavior. Drivers with strong negativity biases reported having been involved in mores crashes compared with the less-biased drivers. The event-related potentials (ERPs revealed that the dangerous drivers exhibited reduced P3 components when responding to negative stimuli, suggesting decreased inhibitory control of information that is task-irrelevant but emotionally salient. The influence of negativity bias provides one possible explanation of the effects of individual differences on dangerous driving behavior and traffic crashes.

Effects of memory rehearsal on driver performance: experiment and theoretical account.

Science.gov (United States)

Salvucci, Dario D; Beltowska, Joanna

2008-10-01

We report an experiment and a theoretical analysis concerning the effects of an exclusively cognitive task, specifically a memory rehearsal task, on driver performance. Although recent work on driver distraction has elucidated the sometimes significant effects of cognitive processing on driver performance, these studies have typically mixed cognitive with perceptual and motor processing, making it difficult to isolate the effects of cognitive processing alone. We asked participants to drive in a driving simulator during only the rehearsal stage of a serial-recall memory task while we measured their ability to maintain a central lane position and respond to the illumination of a lead vehicle's brake lights. Memory rehearsal significantly affected drivers' steering performance as measured by lateral deviation from lane center, and it also significantly affected drivers' response time to the braking stimulus for the higher load memory task. These results lend support to a theoretical account of cognitive distraction provided by threaded cognition theory in terms of a cognitive bottleneck in procedural processing, and they also suggest that consideration of task urgency may be important in accounting for performance trade-offs among concurrent tasks. The experiment augments the current understanding of cognitive driver distraction and suggests that even exclusively cognitive secondary tasks may sometimes affect driver performance.

Driver support and automated driving systems : Acceptance and effects on behavior

NARCIS (Netherlands)

De Waard, D.; Brookhuis, K.A.; Scerbo, MW; Mouloua, M

1999-01-01

Automation in driving ranges from simple in-vehicle information systems to completely automated driving in the Automated Highway System (AHS). An increased level of automation and increased restriction in behavioural freedom, as well as decreased control over tasks, have serious consequences for

Education and driver-training

Directory of Open Access Journals (Sweden)

Andrej Justinek

1999-12-01

Full Text Available The characteristics of the driver are manifested in his/her behaviour. For safe driving one must have a driver's knowledge. The contents of educational material are determined by law, and are both theoretical and practical, yet frequently they do not suffice to meet the requirements of safe driving. In this paper, the author suggests that, in the training of drivers, more educational elements should be included, such a would have  an effective influence on the driver's moti ves and attitudes. The driver's motives - which may result in incorrect driving­ are diverse: most often, the default is overspeeding, even though the drivers always over-estimate the potential time gain. In fact, over-fast driving is a way of satisfying other, different needs; and, above all, it is a form of compensation for unsettled life problems, and at the same time an indication of the driver's personal inability to cope with stress.

Vision based Traffic Sign Detection and Analysis for Intelligent Driver Assistance Systems

DEFF Research Database (Denmark)

Møgelmose, Andreas; Trivedi, Mohan M.; Moeslund, Thomas B.

2012-01-01

In this paper, we provide a survey of the traffic sign detection literature, detailing detection systems for Traffic Sign Recognition (TSR) for driver assistance. We separately describe the contributions of recent works to the various stages inherent in traffic sign detection: segmentation, feature...... extraction, and final sign detection. While TSR is a well-established research area, we highlight open research issues in the literature, including a dearth of use of publicly-available image databases, and the over-representation of European traffic signs. Further, we discuss future directions for TSR...

PCI-VME bridge device driver design of a high-performance data acquisition and control system on LINUX

International Nuclear Information System (INIS)

Sun Yan; Ye Mei; Zhang Nan; Zhao Jingwei

2000-01-01

Data Acquisition and Control is an important part of Nuclear Electronic and Nuclear Detection application in HEP. The key methods are introduced for designing LINUX Device Driver of PCI-VME Bridge Device based on the realized Data Acquisition and Control System

Driver and dispatcher perceptions of AATA's Advanced Operating System

Science.gov (United States)

1999-01-01

This report details results of focus groups and written surveys conducted with AATA motor coach operators. The drivers' early verdict on AOS is favorable overall; limitations in : communication are generally unwelcome, but other services such as auto...

A Framework for Analysing Driver Interactions with Semi-Autonomous Vehicles

Directory of Open Access Journals (Sweden)

Siraj Shaikh

2012-12-01

Full Text Available Semi-autonomous vehicles are increasingly serving critical functions in various settings from mining to logistics to defence. A key characteristic of such systems is the presence of the human (drivers in the control loop. To ensure safety, both the driver needs to be aware of the autonomous aspects of the vehicle and the automated features of the vehicle built to enable safer control. In this paper we propose a framework to combine empirical models describing human behaviour with the environment and system models. We then analyse, via model checking, interaction between the models for desired safety properties. The aim is to analyse the design for safe vehicle-driver interaction. We demonstrate the applicability of our approach using a case study involving semi-autonomous vehicles where the driver fatigue are factors critical to a safe journey.

Driver braking behavior analysis to improve autonomous emergency braking systems in typical Chinese vehicle-bicycle conflicts.

Science.gov (United States)

Duan, Jingliang; Li, Renjie; Hou, Lian; Wang, Wenjun; Li, Guofa; Li, Shengbo Eben; Cheng, Bo; Gao, Hongbo

2017-11-01

Bicycling is one of the fundamental modes of transportation especially in developing countries. Because of the lack of effective protection for bicyclists, vehicle-bicycle (V-B) accident has become a primary contributor to traffic fatalities. Although AEB (Autonomous Emergency Braking) systems have been developed to avoid or mitigate collisions, they need to be further adapted in various conflict situations. This paper analyzes the driver's braking behavior in typical V-B conflicts of China to improve the performance of Bicyclist-AEB systems. Naturalistic driving data were collected, from which the top three scenarios of V-B accidents in China were extracted, including SCR (a bicycle crossing the road from right while a car is driving straight), SCL (a bicycle crossing the road from left while a car is driving straight) and SSR (a bicycle swerving in front of the car from right while a car is driving straight). For safety and data reliability, a driving simulator was employed to reconstruct these three scenarios and some 25 licensed drivers were recruited for braking behavior analysis. Results revealed that driver's braking behavior was significantly influenced by V-B conflict types. Pre-decelerating behaviors were found in SCL and SSR conflicts, whereas in SCR the subjects were less vigilant. The brake reaction time and brake severity in lateral V-B conflicts (SCR and SCL) was shorter and higher than that in longitudinal conflicts (SSR). The findings improve their applications in the Bicyclist-AEB and test protocol enactment to enhance the performance of Bicyclist-AEB systems in mixed traffic situations especially for developing countries. Copyright © 2017 Elsevier Ltd. All rights reserved.

Study on driver model for hybrid truck based on driving simulator experimental results

Directory of Open Access Journals (Sweden)

Dam Hoang Phuc

2018-04-01

Full Text Available In this paper, a proposed car-following driver model taking into account some features of both the compensatory and anticipatory model representing the human pedal operation has been verified by driving simulator experiments with several real drivers. The comparison between computer simulations performed by determined model parameters with the experimental results confirm the correctness of this mathematical driver model and identified model parameters. Then the driver model is joined to a hybrid vehicle dynamics model and the moderate car following maneuver simulations with various driver parameters are conducted to investigate influences of driver parameters on vehicle dynamics response and fuel economy. Finally, major driver parameters involved in the longitudinal control of drivers are clarified. Keywords: Driver model, Driver-vehicle closed-loop system, Car Following, Driving simulator/hybrid electric vehicle (B1

Cognitive functioning differentially predicts different dimensions of older drivers' on-road safety.

Science.gov (United States)

Aksan, Nazan; Anderson, Steve W; Dawson, Jeffrey; Uc, Ergun; Rizzo, Matthew

2015-02-01

The extent to which deficits in specific cognitive domains contribute to older drivers' safety risk in complex real-world driving tasks is not well understood. We selected 148 drivers older than 70 years of age both with and without neurodegenerative diseases (Alzheimer disease-AD and Parkinson disease-PD) from an existing driving database of older adults. Participant assessments included on-road driving safety and cognitive functioning in visuospatial construction, speed of processing, memory, and executive functioning. The standardized on-road drive test was designed to examine multiple facets of older driver safety including navigation performance (e.g., following a route, identifying landmarks), safety errors while concurrently performing secondary navigation tasks ("on-task" safety errors), and safety errors in the absence of any secondary navigation tasks ("baseline" safety errors). The inter-correlations of these outcome measures were fair to moderate supporting their distinctiveness. Participants with diseases performed worse than the healthy aging group on all driving measures and differences between those with AD and PD were minimal. In multivariate analyses, different domains of cognitive functioning predicted distinct facets of driver safety on road. Memory and set-shifting predicted performance in navigation-related secondary tasks, speed of processing predicted on-task safety errors, and visuospatial construction predicted baseline safety errors. These findings support broad assessments of cognitive functioning to inform decisions regarding older driver safety on the road and suggest navigation performance may be useful in evaluating older driver fitness and restrictions in licensing. Copyright © 2014 Elsevier Ltd. All rights reserved.

PCI-VME bridge device driver design of a high-performance data acquisition and control system on LINUX

International Nuclear Information System (INIS)

Sun Yan; Ye Mei; Zhang Nan; Zhao Jingwei

2001-01-01

Data acquisition and control is an important part of nuclear electronic and nuclear detection application in HEP. The key method has been introduced for designing LINUX device driver of PCI-VME bridge device based on realized by authors' data acquisition and control system

Generation of Driver and Reporter Constructs for the GAL4 Expression System in Drosophila.

Science.gov (United States)

Southall, Tony D; Brand, Andrea H

2008-07-01

INTRODUCTIONThe GAL4 system is a method for ectopic gene expression that allows the selective activation of any cloned gene in a wide variety of tissue- and cell-specific patterns. This protocol describes the generation of driver and reporter lines for use with the GAL4 system in Drosophila. A promoter-GAL4 fusion is constructed using a P-element transformable vector, and a GAL4-responsive target gene is created via generation of an upstream activation sequence (UAS)-reporter construct. An alternative strategy for integration using the phiC31 system is also provided. Transformant lines are generated using standard procedures for microinjection.

Factors associated with civilian drivers involved in crashes with emergency vehicles.

Science.gov (United States)

Drucker, Christopher; Gerberich, Susan G; Manser, Michael P; Alexander, Bruce H; Church, Timothy R; Ryan, Andrew D; Becic, Ensar

2013-06-01

Motor vehicle crashes involving civilian and emergency vehicles (EVs) have been a known problem that contributes to fatal and nonfatal injuries; however, characteristics associated with civilian drivers have not been examined adequately. This study used data from The National Highway Traffic Safety Administration's Fatality Analysis Reporting System and the National Automotive Sampling System General Estimates System to identify driver, roadway, environmental, and crash factors, and consequences for civilian drivers involved in fatal and nonfatal crashes with in-use and in-transport EVs. In general, drivers involved in emergency-civilian crashes (ECCs) were more often driving: straight through intersections (vs. same direction) of four-points or more (vs. not at intersection); where traffic signals were present (vs. no traffic control device); and at night (vs. midday). For nonfatal ECCs, drivers were more often driving: distracted (vs. not distracted); with vision obstructed by external objects (vs. no obstruction); on dark but lighted roads (vs. daylight); and in opposite directions (vs. same directions) of the EVs. Consequences included increased risk of injury (vs. no injury) and receiving traffic violations (vs. no violation). Fatal ECCs were associated with driving on urban roads (vs. rural), although these types of crashes were less likely to occur on dark roads (vs. daylight). The findings of this study suggest drivers may have difficulties in visually detecting EVs in different environments. Copyright © 2013 Elsevier Ltd. All rights reserved.

Support system, excavation arrangement, and process of supporting an object

Science.gov (United States)

Arnold, Bill W.

2017-08-01

A support system, an excavation arrangement, and a process of supporting an object are disclosed. The support system includes a weight-bearing device and a camming mechanism positioned below the weight-bearing device. A downward force on the weight-bearing device at least partially secures the camming mechanism to opposing surfaces. The excavation arrangement includes a borehole, a support system positioned within and secured to the borehole, and an object positioned on and supported by the support system. The process includes positioning and securing the support system and positioning the object on the weight-bearing device.

An application of the driver behavior questionnaire to Chinese carless young drivers.

Science.gov (United States)

Zhang, Qian; Jiang, Zuhua; Zheng, Dongpeng; Wang, Yifan; Man, Dong

2013-01-01

Carless young drivers refers to those drivers aged between 18 and 25 years who have a driver's license but seldom have opportunities to practice their driving skills because they do not have their own cars. Due to China's lower private car ownership, many young drivers turn into carless young drivers after licensure, and the safety issue associated with them has become a matter of great concern in China. Because few studies have examined the driving behaviors of these drivers, this study aims to utilize the Driver Behavior Questionnaire (DBQ) to investigate the self-reported driving behaviors of Chinese carless young drivers. A total of 523 Chinese carless young drivers (214 females, 309 males) with an average age of 21.91 years completed a questionnaire including the 27-item DBQ and demographics. The data were first randomized into 2 subsamples for factor analysis and then combined together for the following analyses. Both an exploratory factor analysis (EFA, n = 174) and a confirmatory factor analysis (CFA, n = 349) were performed to investigate the factor structure of the DBQ. Correlation analysis was conducted to examine the relationships between the demographics and the DBQ scales' variables. Multivariate linear regression and logistic regression were performed to investigate the prediction of the DBQ scales and crash involvement in the previous year. The EFA produced a 4-factor structure identified as errors, violations, attention lapses, and memory lapses, and the CFA revealed a good model fit after the removal of one item with a low factor loading and the permission of the error covariance between some items. The Chinese carless young drivers reported a comparatively low level of aberrant driving behaviors. The 3 most frequently reported behaviors were all lapses and the 3 least were all violations. Gender was the only significant predictor of the 2 lapses scales and lifetime mileage was the only significant predictor of the violations scale. Only the

Parent attitudes toward integrating parent involvement into teenage driver education courses.

Science.gov (United States)

Hartos, Jessica; Huff, David C

2008-01-01

The widespread adoption of graduated driver licensing (GDL) policies has effectively reduced crash risk for young drivers; however, parents must support, reinforce, and enforce GDL for it to be effective, and research indicates that parents need better information and instruction for adhering to GDL requirements, conducting supervised practice driving, and restricting independent teenage driving. Because teenagers in most states must take driver education to enter the licensing process prior to age 18, integrating parent involvement into driver education may be an effective way to inform and instruct parents on a large scale about teen driver safety. This study assessed parent attitudes (overall and by rural status, minority status, and income level) toward integrating parent involvement into teenage driver education classes. In this study, 321 parents of teenagers enrolled in driver education classes across the state of Montana completed surveys about current involvement in driver education and attitudes toward required involvement. The results indicated that parents were not very involved currently in their teenagers' driver education classes, but 76% reported that parents should be required to be involved. If involvement were required, parents would prefer having written materials sent home, access to information over the Internet, or discussions in person with the instructor; far fewer would prefer to attend classes or behind-the-wheel driving instruction. There were few differences in parent attitudes by rural or minority status but many by income level. Compared to higher income parents, lower income parents were more likely to endorse required parent involvement in teenage driver education classes and to want parent information from driver education about many teen driving issues. That the majority of parents are open to required involvement in their teenagers' driver education classes is promising because doing so could better prepare parents to understand

A method for making a glass supported system, such glass supported system, and the use of a glass support therefor

NARCIS (Netherlands)

Unnikrishnan, S.; Jansen, Henricus V.; Berenschot, Johan W.; Fazal, I.; Louwerse, M.C.; Mogulkoc, B.; Sanders, Remco G.P.; de Boer, Meint J.; Elwenspoek, Michael Curt

2008-01-01

The invention relates to a method for making a glass supported micro or nano system, comprising the steps of: i) providing a glass support; ii) mounting at least one system on at least one glass support; and iii) bonding the system to the glass support, such that the system is circumferentially

Description and operating performance of a parallel-rail electric-arc system with helium driver gas for the Langley 6-inch expansion tube

Science.gov (United States)

Moore, J. A.

1976-01-01

A parallel-rail arc-discharge system to heat and pressurize the initial helium driver gas of the Langley 6-inch expansion tube is described. This system was designed for a 2.44-m-long driver vessel rated at 138 MPa, with a distance between rails of 20.3 cm. Electric energy was obtained from a capacitor storage system rated at 12,000 V with a maximum energy of 5 MJ. Tests were performed over a range of energy from 1.74 MJ to the maximum value. The operating experience and system performance are discussed, along with results from a limited number of expansion-tube tests with air and carbon dioxide as test gases.

Are cellular phone blocking applications effective for novice teen drivers?

Science.gov (United States)

Creaser, Janet I; Edwards, Christopher J; Morris, Nichole L; Donath, Max

2015-09-01

Distracted driving is a significant concern for novice teen drivers. Although cellular phone bans are applied in many jurisdictions to restrict cellular phone use, teen drivers often report making calls and texts while driving. The Minnesota Teen Driver Study incorporated cellular phone blocking functions via a software application for 182 novice teen drivers in two treatment conditions. The first condition included 92 teens who ran a driver support application on a smartphone that also blocked phone usage. The second condition included 90 teens who ran the same application with phone blocking but which also reported back to parents about monitored risky behaviors (e.g., speeding). A third control group consisting of 92 novice teen drivers had the application and phone-based software installed on the phones to record cellular phone (but not block it) use while driving. The two treatment groups made significantly fewer calls and texts per mile driven compared to the control group. The control group data also demonstrated a higher propensity to text while driving rather than making calls. Software that blocks cellular phone use (except 911) while driving can be effective at mitigating calling and texting for novice teen drivers. However, subjective data indicates that some teens were motivated to find ways around the software, as well as to use another teen's phone while driving when they were unable to use theirs. Cellular phone bans for calling and texting are the first step to changing behaviors associated with texting and driving, particularly among novice teen drivers. Blocking software has the additional potential to reduce impulsive calling and texting while driving among novice teen drivers who might logically know the risks, but for whom it is difficult to ignore calling or texting while driving. Copyright © 2015 Elsevier Ltd and National Safety Council. All rights reserved.

The vehicle dynamics control system of Bosch; Die Fahrdynamikregelung von Bosch

Energy Technology Data Exchange (ETDEWEB)

Zanten, A.T. van [Robert Bosch GmbH, Stuttgart (Germany); Erhardt, R. [Robert Bosch GmbH, Stuttgart (Germany); Pfaff, G. [Robert Bosch GmbH, Stuttgart (Germany)

1996-11-01

Vehicle handling at the physical limit of adhesion between the tires and the road is extremely difficult. In such situations the driver may be supported by controlling the longitudinal and the lateral forces on the tires. The Vehicle Dynamics Control System of Bosch (VDC) does that by controlled braking of individual wheels which makes the vehicle motion approach the nomial motion intended by the driver. It uses signals to derive the driver`s intent (steering wheel angle, brake pressure, engine torque) and signals to dervie the actual motion of the vehicle (yaw rate, lateral acceleration). The support of the driver is not limited to coasting conditions. Also during full braking (ABS), partial braking, engine drag, free rolling and acceleration (ASR) of the vehicle the system supports the driver in all safety critical situations. In this paper an overview of the VDC is given. The goal of the development of VDC, the physical background, the concept of the system, the control and the controller algorithm are described. The benefit of VDC is demonstrated by an experimental test. (orig.) [Deutsch] Fahrdynamikregelsysteme FDR sind Regelsysteme im Bremssystem und Antriebsstrang, die das seitliche Ausbrechen des Fahrzeugs verhindern. Waehrend ABS das Blockieren der Raeder beim Bremsen und ASR das Durchdrehen der Raeder beim Antrieb verhindert, verhindert FDR das Schleudern und das Schieben des Fahrzeugs. (orig.)

Levitation With a Single Acoustic Driver

Science.gov (United States)

Barmatz, M. B.; Gaspar, M. S.; Allen, J. L.

1986-01-01

Pair of reports describes acoustic-levitation systems in which only one acoustic resonance mode excited, and only one driver needed. Systems employ levitation chambers of rectangular and cylindrical geometries. Reports first describe single mode concept and indicate which modes used to levitate sample without rotation. Reports then describe systems in which controlled rotation of sample introduced.

Leveraging accelerated testing of LED drivers to model the reliability of two-stage and multi-channel drivers

Energy Technology Data Exchange (ETDEWEB)

Davis, Lynn; Perkins, Curtis; Smith, Aaron; Clark, Terry; Mills, Karmann

2017-05-30

The next wave of LED lighting technology is likely to be tunable white lighting (TWL) devices which can adjust the colour of the emitted light between warm white (~ 2700 K) and cool white (~ 6500 K). This type of lighting system uses LED assemblies of two or more colours each controlled by separate driver channels that independently adjust the current levels to achieve the desired lighting colour. Drivers used in TWL devices are inherently more complex than those found in simple SSL devices, due to the number of electrical components in the driver required to achieve this level of control. The reliability of such lighting systems can only be studied using accelerated stress tests (AST) that accelerate the aging process to time frames that can be accommodated in laboratory testing. This paper describes AST methods and findings developed from AST data that provide insights into the lifetime of the main components of one-channel and multi-channel LED devices. The use of AST protocols to confirm product reliability is necessary to ensure that the technology can meet the performance and lifetime requirements of the intended application.

Driver behavior following an automatic steering intervention.

Science.gov (United States)

Fricke, Nicola; Griesche, Stefan; Schieben, Anna; Hesse, Tobias; Baumann, Martin

2015-10-01

The study investigated driver behavior toward an automatic steering intervention of a collision mitigation system. Forty participants were tested in a driving simulator and confronted with an inevitable collision. They performed a naïve drive and afterwards a repeated exposure in which they were told to hold the steering wheel loosely. In a third drive they experienced a false alarm situation. Data on driving behavior, i.e. steering and braking behavior as well as subjective data was assessed in the scenarios. Results showed that most participants held on to the steering wheel strongly or counter-steered during the system intervention during the first encounter. Moreover, subjective data collected after the first drive showed that the majority of drivers was not aware of the system intervention. Data from the repeated drive in which participants were instructed to hold the steering wheel loosely, led to significantly more participants holding the steering wheel loosely and thus complying with the instruction. This study seems to imply that without knowledge and information of the system about an upcoming intervention, the most prevalent driving behavior is a strong reaction with the steering wheel similar to an automatic steering reflex which decreases the system's effectiveness. Results of the second drive show some potential for countermeasures, such as informing drivers shortly before a system intervention in order to prevent inhibiting reactions. Copyright © 2015 Elsevier Ltd. All rights reserved.

A novel algorithm for finding optimal driver nodes to target control complex networks and its applications for drug targets identification.

Science.gov (United States)

Guo, Wei-Feng; Zhang, Shao-Wu; Shi, Qian-Qian; Zhang, Cheng-Ming; Zeng, Tao; Chen, Luonan

2018-01-19

The advances in target control of complex networks not only can offer new insights into the general control dynamics of complex systems, but also be useful for the practical application in systems biology, such as discovering new therapeutic targets for disease intervention. In many cases, e.g. drug target identification in biological networks, we usually require a target control on a subset of nodes (i.e., disease-associated genes) with minimum cost, and we further expect that more driver nodes consistent with a certain well-selected network nodes (i.e., prior-known drug-target genes). Therefore, motivated by this fact, we pose and address a new and practical problem called as target control problem with objectives-guided optimization (TCO): how could we control the interested variables (or targets) of a system with the optional driver nodes by minimizing the total quantity of drivers and meantime maximizing the quantity of constrained nodes among those drivers. Here, we design an efficient algorithm (TCOA) to find the optional driver nodes for controlling targets in complex networks. We apply our TCOA to several real-world networks, and the results support that our TCOA can identify more precise driver nodes than the existing control-fucus approaches. Furthermore, we have applied TCOA to two bimolecular expert-curate networks. Source code for our TCOA is freely available from http://sysbio.sibcb.ac.cn/cb/chenlab/software.htm or https://github.com/WilfongGuo/guoweifeng . In the previous theoretical research for the full control, there exists an observation and conclusion that the driver nodes tend to be low-degree nodes. However, for target control the biological networks, we find interestingly that the driver nodes tend to be high-degree nodes, which is more consistent with the biological experimental observations. Furthermore, our results supply the novel insights into how we can efficiently target control a complex system, and especially many evidences on the

Managers’ Support – A Key Driver behind Enterprise Risk Management Maturity

Directory of Open Access Journals (Sweden)

Sprčić Danijela Miloš

2017-04-01

Full Text Available Severe consequences of the global fi nancial crisis resulted in re-thinking the risk management processes and approaches, highlighting the need for a comprehensive risk management framework. Consequently, more and more companies are moving away from the Traditional “silo-based” Risk Management (TRM to a more holistic approach known as Enterprise Risk Management (ERM. This paper presents results of both exploratory and empirical research. First, we develop ERM Index that measures maturity of ERM process within the company. Then, we present empirical results on the level of maturity and determinants of risk management system development in listed Croatian companies. Research indicates low levels of ERM development: even 38 per cent of analysed companies have no elements of ERM system, from which 22 per cent do not manage corporate risks at all. Except the company’s size supported by the economies of scale argument, managers’ support is the most important determinant of ERM system maturity in Croatian companies.

The role of simulation in the assessment of older drivers.

NARCIS (Netherlands)

Sommer, Sascha; Rothermel, Stefan; Henriksson, Per; de Waard, Dick; Brookhuis, Karel; Sommer, Sascha; Verwey, Willem B.

2003-01-01

Within the project AGILE an assessment system for ageing drivers is developed. A multi-tier procedure including simulator-based diagnostic tests is will be created. Objective driver performance measurement, design of risky scenarios to test performance limits and high face validity are benefits of

Characteristics of Chinese Driver Behavior

NARCIS (Netherlands)

Li, J.

2014-01-01

The high growth rate of vehicle ownership and many novel drivers in China determine the special features of Chinese driver behavior. This thesis introduces a comparative study on driver behavior by the analysis of saturation flow at urban intersections, Driver Behavior Questionnaire surveys, focus

Fatigue in Younger and Older Drivers: Effectiveness of an Alertness-Maintaining Task.

Science.gov (United States)

Song, Woojin; Woon, Fu L; Doong, Alice; Persad, Carol; Tijerina, Louis; Pandit, Pooja; Cline, Carol; Giordani, Bruno

2017-09-01

The aim of this study was to examine the effects of an alertness-maintaining task (AMT) in older, fatigued drivers. Fatigue during driving increases crash risk, and previous research suggests that alertness and driving in younger adults may be improved using a secondary AMT during boring, fatigue-eliciting drives. However, the potential impact of an AMT on driving has not been investigated in older drivers whose ability to complete dual tasks has been shown to decline and therefore may be negatively affected with an AMT in driving. Younger ( n = 29) and older drivers ( n = 39) participated in a 50-minute simulated drive designed to induce fatigue, followed by four 10-minute sessions alternating between driving with and without an AMT. Younger drivers were significantly more affected by fatigue on driving performance than were older drivers but benefitted significantly from the AMT. Older drivers did not demonstrate increased driver errors with fatigue, and driving did not deteriorate significantly during participation in the AMT condition, although their speed was significantly more variable with the AMT. Consistent with earlier research, an AMT applied during fatiguing driving is effective in improving alertness and reducing driving errors in younger drivers. Importantly, older drivers were relatively unaffected by fatigue, and use of an AMT did not detrimentally affect their driving performance. These results support the potential use of an AMT as a new automotive technology to improve fatigue and promote driver safety, though the benefits of such technology may differ between different age groups.

Crash probability estimation via quantifying driver hazard perception.

Science.gov (United States)

Li, Yang; Zheng, Yang; Wang, Jianqiang; Kodaka, Kenji; Li, Keqiang

2018-07-01

Crash probability estimation is an important method to predict the potential reduction of crash probability contributed by forward collision avoidance technologies (FCATs). In this study, we propose a practical approach to estimate crash probability, which combines a field operational test and numerical simulations of a typical rear-end crash model. To consider driver hazard perception characteristics, we define a novel hazard perception measure, called as driver risk response time, by considering both time-to-collision (TTC) and driver braking response to impending collision risk in a near-crash scenario. Also, we establish a driving database under mixed Chinese traffic conditions based on a CMBS (Collision Mitigation Braking Systems)-equipped vehicle. Applying the crash probability estimation in this database, we estimate the potential decrease in crash probability owing to use of CMBS. A comparison of the results with CMBS on and off shows a 13.7% reduction of crash probability in a typical rear-end near-crash scenario with a one-second delay of driver's braking response. These results indicate that CMBS is positive in collision prevention, especially in the case of inattentive drivers or ole drivers. The proposed crash probability estimation offers a practical way for evaluating the safety benefits in the design and testing of FCATs. Copyright © 2017 Elsevier Ltd. All rights reserved.

Modelling the influence of sensory dynamics on linear and nonlinear driver steering control

Science.gov (United States)

Nash, C. J.; Cole, D. J.

2018-05-01

A recent review of the literature has indicated that sensory dynamics play an important role in the driver-vehicle steering task, motivating the design of a new driver model incorporating human sensory systems. This paper presents a full derivation of the linear driver model developed in previous work, and extends the model to control a vehicle with nonlinear tyres. Various nonlinear controllers and state estimators are compared with different approximations of the true system dynamics. The model simulation time is found to increase significantly with the complexity of the controller and state estimator. In general the more complex controllers perform best, although with certain vehicle and tyre models linearised controllers perform as well as a full nonlinear optimisation. Various extended Kalman filters give similar results, although the driver's sensory dynamics reduce control performance compared with full state feedback. The new model could be used to design vehicle systems which interact more naturally and safely with a human driver.

Management Accounting as a Knowledge Based Organization Value Driver for the 21st Century Business

Directory of Open Access Journals (Sweden)

Daraban Marius Costin

2017-01-01

Full Text Available The 21st century information and information technology revolution has made its mark onclassical business functions like business support services. Management accounting, a still youngbusiness activity has transformed from reactive cost determination focus to proactive valuecreating and considerate resource business driver. Management accounting is on the way toasserting itself as a proactive business value driver for the modern 21st century businessorganizations. The present paper is presenting the arguments that support the transformation ofmanagement accounting from the “bean counter” score keeping role to value driver supported byknowledge, the prime commodity of the 21st century business environment. Managementaccounting is the business partner that delivers reliable and accurate data and information for thebusiness decision process that is more and more influenced globalization, internationalization andaccelerating and dynamic markets. Can modern companies afford to disregard the dormant valuedrivers from within their own business organization?

The Use of Persuasive In-Car Technology to Persuade Drivers at the Tactical Level

NARCIS (Netherlands)

van Gent, P.; Farah, H.; Nes, Nicole Van; van Arem, B.

2017-01-01

The use of in-car technology has become more prevalent, both as driver assistance systems as well as connectivity or entertainment systems. Driver assistance systems can be built-in, after-market or run on a smartphone. The challenge however, is to increase drivers’ compliance with these systems.

S-Band POSIX Device Drivers for RTEMS

Science.gov (United States)

Lux, James P.; Lang, Minh; Peters, Kenneth J.; Taylor, Gregory H.

2011-01-01

This is a set of POSIX device driver level abstractions in the RTEMS RTOS (Real-Time Executive for Multiprocessor Systems real-time operating system) to SBand radio hardware devices that have been instantiated in an FPGA (field-programmable gate array). These include A/D (analog-to-digital) sample capture, D/A (digital-to-analog) sample playback, PLL (phase-locked-loop) tuning, and PWM (pulse-width-modulation)-controlled gain. This software interfaces to Sband radio hardware in an attached Xilinx Virtex-2 FPGA. It uses plug-and-play device discovery to map memory to device IDs. Instead of interacting with hardware devices directly, using direct-memory mapped access at the application level, this driver provides an application programming interface (API) offering that easily uses standard POSIX function calls. This simplifies application programming, enables portability, and offers an additional level of protection to the hardware. There are three separate device drivers included in this package: sband_device (ADC capture and DAC playback), pll_device (RF front end PLL tuning), and pwm_device (RF front end AGC control).

GPS Usage in a Population of Low-Vision Drivers.

Science.gov (United States)

Cucuras, Maria; Chun, Robert; Lee, Patrick; Jay, Walter M; Pusateri, Gregg

2017-01-01

We surveyed bioptic and non-bioptic low-vision drivers in Illinois, USA, to determine their usage of global positioning system (GPS) devices. Low-vision patients completed an IRB-approved phone survey regarding driving demographics and usage of GPS while driving. Participants were required to be active drivers with an Illinois driver's license, and met one of the following criteria: best-corrected visual acuity (BCVA) less than or equal to 20/40, central or significant peripheral visual field defects, or a combination of both. Of 27 low-vision drivers, 10 (37%) used GPS while driving. The average age for GPS users was 54.3 and for non-users was 77.6. All 10 drivers who used GPS while driving reported increased comfort or safety level. Since non-GPS users were significantly older than GPS users, it is likely that older participants would benefit from GPS technology training from their low-vision eye care professionals.

Drivers' perceptions regarding speeding and driving on urban residential streets with a 30 km/h speed limit

Directory of Open Access Journals (Sweden)

Do Duy Dinh

2013-07-01

Full Text Available Previous studies have shown very little information regarding drivers' opinions, attitudes and behaviours with respect to speeding and driving on urban residential streets with a 30 km/h speed limit. The present research aims to address this issue by conducting a questionnaire study with a sample of 367 Japanese drivers. The results showed that drivers tended to have positive beliefs about complying with the 30 km/h speed limit and understand the negative consequences of speeding; however, a majority of the drivers considered breaking the speed limit as a way to reduce their travel time. While the extent of speeding was found to be very serious, a number of drivers still supported the use of a 30 km/h speed limit on residential streets and favoured protecting the right of vulnerable street users. The logistic regression models developed in this study identified that the drivers who did not support the 30 km/h speed limit were associated with those who had committed traffic-law violations, who had negative beliefs about complying with the speed limit, who did not consider residents' opinions, who believed it is acceptable for them to drive at a high speed, and who felt it difficult to refrain from speeding. With regard to anti-speeding countermeasures, under drivers' point of view, streets should be designed to make the 30 km/h speed limit more credible, although this study also showed evidence supporting the application of public awareness programmes and social campaigns as speeding interventions. In addition, this research investigated drivers' speed choices in various specific driving circumstances, and six underlying factors affecting drivers' speed choices were determined. On the basic of the findings, the implications and suggestions for speeding interventions were also discussed.

Real-time Alarm Monitoring System for Detecting Driver Fatigue in Wireless Areas

Directory of Open Access Journals (Sweden)

Rongrong Fu

2017-04-01

Full Text Available The purpose of this paper was to develop a real-time alarm monitoring system that can detect the fatigue driving state through wireless communication. The drivers’ electroencephalogram (EEG signals were recorded from occipital electrodes. Seven EEG rhythms with different frequency bands as gamma, hbeta, beta, sigma, alpha, theta and delta waves were extracted. They were simultaneously assessed using relative operating characteristic (ROC curves and grey relational analysis to select one as the fatigue feature. The research results showed that the performance of theta wave was the best one. Therefore, theta wave was used as fatigue feature in the following alarm device. The real-time alarm monitoring system based on the result has been developed, once the threshold was settled by using the data of the first ten minutes driving period. The developed system can detect driver fatigue and give alarm to indicate the onset of fatigue automatically.

Modeling and Recognizing Driver Behavior Based on Driving Data: A Survey

OpenAIRE

Wang, Wenshuo; Xi, Junqiang; Chen, Huiyan

2014-01-01

In recent years, modeling and recognizing driver behavior have become crucial to understanding intelligence transport systems, human-vehicle systems, and intelligent vehicle systems. A wide range of both mathematical identification methods and modeling methods of driver behavior are presented from the control point of view in this paper based on the driving data, such as the brake/throttle pedal position and the steering wheel angle, among others. Subsequently, the driver’s characteristics de...

Assessing the relationship between the Driver Behavior Questionnaire and the Driver Skill Inventory: Revealing sub-groups of drivers

DEFF Research Database (Denmark)

Martinussen, Laila Marianne; Møller, Mette; Prato, Carlo Giacomo

2014-01-01

The Driver Behavior Questionnaire and the Driver Skill Inventory are two of the most frequently used measures of self-reported driving style and driving skill. The motivation behind the present study was to identify sub-groups of drivers that potentially act dangerously in traffic (as measured...... self-reported driving skills and whether the reported skill level was reflected in the reported aberrant driving behaviors. 3908 drivers aged 18–84 participated in the survey. K-means cluster analysis revealed four distinct sub-groups that differed in driving skills and frequency of aberrant driving...... by frequency of aberrant driving behaviors and level of driving skills), as well as to test whether the sub-groups differ in characteristics such as age, gender, annual mileage and accident involvement. Furthermore, the joint analysis of the two instruments was used to test drivers’ assessment of their own...

Heavy-ion driver design and scaling

International Nuclear Information System (INIS)

Bieri, R.; Monsler, M.; Meier, W.; Stewart, L.

1992-01-01

Parametric models for scaling heavy-ion driver designs are described. Scaling of target performance and driver cost is done for driver parameters including driver energy, number of beams, type of superconductor used in focusing magnets, maximum magnetic field allowed at the superconducting windings, linear quadrupole array packing fraction mass, and ion charge state. The cumulative accelerator voltage and beam currents are determined from the Maschke limits on beam current for each choice of driver energy and post-acceleration pulse duration. The heavy-ion driver is optimized over the large available driver parameter space. Parametric studies and the choice of a base driver model are described in a companion paper

High-Voltage LED Light Engine with Integrated Driver

Energy Technology Data Exchange (ETDEWEB)

Soer, Wouter [Lumileds LLC, San Jose, CA (United States)

2016-02-29

LED luminaires have seen dramatic changes in cost breakdown over the past few years. The LED component cost, which until recently was the dominant portion of luminaire cost, has fallen to a level of the same order as the other luminaire components, such as the driver, housing, optics etc. With the current state of the technology, further luminaire performance improvement and cost reduction is realized most effectively by optimization of the whole system, rather than a single component. This project focuses on improving the integration between LEDs and drivers. Lumileds has developed a light engine platform based on low-cost high-power LEDs and driver topologies optimized for integration with these LEDs on a single substrate. The integration of driver and LEDs enables an estimated luminaire cost reduction of about 25% for targeted applications, mostly due to significant reductions in driver and housing cost. The high-power LEDs are based on Lumileds’ patterned sapphire substrate flip-chip (PSS-FC) technology, affording reduced die fabrication and packaging cost compared to existing technology. Two general versions of PSS-FC die were developed in order to create the desired voltage and flux increments for driver integration: (i) small single-junction die (0.5 mm²), optimal for distributed lighting applications, and (ii) larger multi-junction die (2 mm² and 4 mm²) for high-power directional applications. Two driver topologies were developed: a tapped linear driver topology and a single-stage switch-mode topology, taking advantage of the flexible voltage configurations of the new PSS-FC die and the simplification opportunities enabled by integration of LEDs and driver on the same board. A prototype light engine was developed for an outdoor “core module” application based on the multi-junction PSS-FC die and the single-stage switch-mode driver. The light engine meets the project efficacy target of 128 lm/W at a luminous flux

Drivers of health system strengthening: learning from implementation of maternal and child health programmes in Mozambique, Nepal and Rwanda.

Science.gov (United States)

Samuels, Fiona; Amaya, Ana B; Balabanova, Dina

2017-09-01

There is a growing understanding that strong health systems are crucial to sustain progress. Health systems, however, are complex and much of their success depends on factors operating at different levels and outside the health system, including broader governance and political commitment to health and social development priorities. Recognizing these complexities, this article offers a pragmatic approach to exploring the drivers of progress in maternal and child health in Mozambique, Nepal and Rwanda. To do this, the article builds on a semi-systematic literature review and case study findings, designed and analysed using a multi-level framework. At the macro level, governance with effective and committed leaders was found to be vital for achieving positive health outcomes. This was underpinned by clear commitment from donors coupled by a significant increase in funding to the health sector. At the meso level, where policies are operationalized, inter-sectoral partnerships as well as decentralization and task-shifting emerged as critical. At micro (service interface) level, community-centred models and accessible and appropriately trained and incentivized local health providers play a central role in all study countries. The key drivers of progress are multiple, interrelated and transversal in terms of their operation; they are also in a constant state of flux as health systems and contexts develop. Without seeking to offer a blueprint, the study demonstrates that a 'whole-system' approach can help elicit the key drivers of change and potential pathways towards desirable outcomes. Furthermore, understanding the challenges and opportunities that are instrumental to progress at each particular level of a health system can help policy-makers and implementers to navigate this complexity and take action to strengthen health systems. © The Author 2017. Published by Oxford University Press in association with The London School of Hygiene and Tropical Medicine. All rights

Observed and projected drivers of emerging infectious diseases in Europe.

Science.gov (United States)

Semenza, Jan C; Rocklöv, Joacim; Penttinen, Pasi; Lindgren, Elisabet

2016-10-01

Emerging infectious diseases are of international concern because of the potential for, and impact of, pandemics; however, they are difficult to predict. To identify the drivers of disease emergence, we analyzed infectious disease threat events (IDTEs) detected through epidemic intelligence collected at the European Centre for Disease Prevention and Control (ECDC) between 2008 and 2013, and compared the observed results with a 2008 ECDC foresight study of projected drivers of future IDTEs in Europe. Among 10 categories of IDTEs, foodborne and waterborne IDTEs were the most common, vaccine-preventable IDTEs caused the highest number of cases, and airborne IDTEs caused the most deaths. Observed drivers for each IDTE were sorted into three main groups: globalization and environmental drivers contributed to 61% of all IDTEs, public health system drivers contributed to 21%, and social and demographic drivers to 18%. A multiple logistic regression analysis showed that four of the top five drivers for observed IDTEs were in the globalization and environment group. In the observational study, the globalization and environment group was related to all IDTE categories, but only to five of eight categories in the foresight study. Directly targeting these drivers with public health interventions may diminish the chances of IDTE occurrence from the outset. © 2016 New York Academy of Sciences.

The TRAIN-project: railway safety and the train driver information environment and work situation. A summary of the main results

Energy Technology Data Exchange (ETDEWEB)

Kecklund, L. [MTO Psychology and Swedish National Rail Administration (Sweden); Ingre, M.; Kecklund, G.; Soederstroem, M.; Aakerstedt, T. [National Inst. for Psychosocial Factors and Health (Sweden); Lindberg, E. [Swedish National Rail Administration (Sweden); Jansson, A.; Olsson, E.; Sandblad, B. [Uppsala Univ. (Sweden). Dept. of Human-Computer Interaction; Almqvist, P. [Swedish State Railways (Sweden)

2001-07-01

The TRAIN project investigates traffic safety related risks, focusing in particular on the train driver work situation, use of information but also on the supporting safety organisation. It is an on-going project funded and managed by Swedish National Rail Administration and carried out by independent researchers. The project provides a multi-disciplinary investigation by use of a man-technology-organisation (MTO) perspective. Activities performed are task analysis, evaluation of the drivers use of information and interaction with the ATP system as well as analyses of stress, mental workload and work hours. Several methods are being used such as interviews, questionnaires, diaries, activity monitoring and videotapes. This paper gives an overview of the project as well as a short summary of the main results. Detailed results are presented in separate reports as started in the reference list. Some of the main results are that the drivers report severe problems concerning sleepiness on early morning shifts, problems with maintenance on vehicles, lack of information supporting the planning task as well as problems in understanding ATP functions. Two groups of drivers having a feed-back related as opposed to a feed-forward driving style could be identified. In conclusion there is a great need to perform more scientific studies of human factors and railway safety as well as to implement safety management programs including professional human factors competence in the railway industries. (orig.)

Using Shadow Page Cache to Improve Isolated Drivers Performance

Directory of Open Access Journals (Sweden)

Hao Zheng

2015-01-01

Full Text Available With the advantage of the reusability property of the virtualization technology, users can reuse various types and versions of existing operating systems and drivers in a virtual machine, so as to customize their application environment. In order to prevent users’ virtualization environments being impacted by driver faults in virtual machine, Chariot examines the correctness of driver’s write operations by the method of combining a driver’s write operation capture and a driver’s private access control table. However, this method needs to keep the write permission of shadow page table as read-only, so as to capture isolated driver’s write operations through page faults, which adversely affect the performance of the driver. Based on delaying setting frequently used shadow pages’ write permissions to read-only, this paper proposes an algorithm using shadow page cache to improve the performance of isolated drivers and carefully study the relationship between the performance of drivers and the size of shadow page cache. Experimental results show that, through the shadow page cache, the performance of isolated drivers can be greatly improved without impacting Chariot’s reliability too much.

Older drivers : a review.

NARCIS (Netherlands)

Hakamies-Blomqvist, L. Sirén, A. & Davidse, R.J.

2004-01-01

The proportion of senior citizens (aged 65+) will grow from about 15 per cent in the year 2000 to about 30 per cent in the year 2050. The share of older drivers in the driver population will grow even faster because of increasing licensing rates among the ageing population. Older drivers do not have

A numerical tool for reproducing driver behaviour: experiments and predictive simulations.

Science.gov (United States)

Casucci, M; Marchitto, M; Cacciabue, P C

2010-03-01

This paper presents the simulation tool called SDDRIVE (Simple Simulation of Driver performance), which is the numerical computerised implementation of the theoretical architecture describing Driver-Vehicle-Environment (DVE) interactions, contained in Cacciabue and Carsten [Cacciabue, P.C., Carsten, O. A simple model of driver behaviour to sustain design and safety assessment of automated systems in automotive environments, 2010]. Following a brief description of the basic algorithms that simulate the performance of drivers, the paper presents and discusses a set of experiments carried out in a Virtual Reality full scale simulator for validating the simulation. Then the predictive potentiality of the tool is shown by discussing two case studies of DVE interactions, performed in the presence of different driver attitudes in similar traffic conditions.

Why do drivers maintain short headways in fog? A driving-simulator study evaluating feeling of risk and lateral control during automated and manual car following.

Science.gov (United States)

Saffarian, M; Happee, R; Winter, J C F de

2012-01-01

Drivers in fog tend to maintain short headways, but the reasons behind this phenomenon are not well understood. This study evaluated the effect of headway on lateral control and feeling of risk in both foggy and clear conditions. Twenty-seven participants completed four sessions in a driving simulator: clear automated (CA), clear manual (CM), fog automated (FA) and fog manual (FM). In CM and FM, the drivers used the steering wheel, throttle and brake pedals. In CA and FA, a controller regulated the distance to the lead car, and the driver only had to steer. Drivers indicated how much risk they felt on a touchscreen. Consistent with our hypothesis, feeling of risk and steering activity were elevated when the lead car was not visible. These results might explain why drivers adopt short headways in fog. Practitioner Summary: Fog poses a serious road safety hazard. Our driving-simulator study provides the first experimental evidence to explain the role of risk-feeling and lateral control in headway reduction. These results are valuable for devising effective driver assistance and support systems.

The role of looming and attention capture in drivers' braking responses.

Science.gov (United States)

Terry, Hugh R; Charlton, Samuel G; Perrone, John A

2008-07-01

This study assessed the ability of drivers to detect the deceleration of a preceding vehicle in a simulated vehicle-following task. The size of the preceding vehicles (car, van, or truck) and following speeds (50, 70, or 100 km/h) were systematically varied. Participants selected a preferred following distance by engaging their vehicle's cruise control and when the preceding vehicle began decelerating (no brake lights were illuminated), the participant's braking latency and distances to the lead vehicle were recorded. The experiment also employed a secondary task condition to examine how the attention-capturing properties of a looming vehicle were affected by driver distraction. The results indicated that a looming stimulus is capable of redirecting a driver's attention in a vehicle following task and, as with detection of brake lights, a driver's detection of a looming vehicle is compromised in the presence of a distracting task. Interestingly, increases in vehicle size had the effect of decreasing drivers' braking latencies and drivers engaged in the secondary task were significantly closer to the lead vehicle when they began braking, regardless of the size of the leading vehicle. Performance decrements resulting from the secondary task were reflected in a time-to-collision measure but not in optic expansion rate, lending support to earlier arguments that time-to-collision estimates require explicit cognitive judgements while perception of optic expansion may function in a more automatic fashion to redirect a driver's attention when cognitive resources are low or collision is imminent.

Using Self-Reliance Factors to Decide How to Share Control Between Human Powered Wheelchair Drivers and Ultrasonic Sensors.

Science.gov (United States)

Sanders, David A

2017-08-01

A shared-control scheme for a powered wheelchair is presented. The wheelchair can be operated by a wheelchair driver using a joystick, or directed by a sensor system, or control can be combined between them. The wheelchair system can modify direction depending on the local environment. Sharing the control allows a disabled wheelchair driver to drive safely and efficiently. The controller automatically establishes the control gains for the sensor system and the human driver by calculating a self-reliance factor for the wheelchair driver. The sensor system can influence the motion of the wheelchair to compensate for some deficiency in a disabled driver. Practical tests validate the proposed techniques and designs.

Orangutan Alu quiescence reveals possible source element: support for ancient backseat drivers

Directory of Open Access Journals (Sweden)

Walker Jerilyn A

2012-04-01

Full Text Available Abstract Background Sequence analysis of the orangutan genome revealed that recent proliferative activity of Alu elements has been uncharacteristically quiescent in the Pongo (orangutan lineage, compared with all previously studied primate genomes. With relatively few young polymorphic insertions, the genomic landscape of the orangutan seemed like the ideal place to search for a driver, or source element, of Alu retrotransposition. Results Here we report the identification of a nearly pristine insertion possessing all the known putative hallmarks of a retrotranspositionally competent Alu element. It is located in an intronic sequence of the DGKB gene on chromosome 7 and is highly conserved in Hominidae (the great apes, but absent from Hylobatidae (gibbon and siamang. We provide evidence for the evolution of a lineage-specific subfamily of this shared Alu insertion in orangutans and possibly the lineage leading to humans. In the orangutan genome, this insertion contains three orangutan-specific diagnostic mutations which are characteristic of the youngest polymorphic Alu subfamily, AluYe5b5_Pongo. In the Homininae lineage (human, chimpanzee and gorilla, this insertion has acquired three different mutations which are also found in a single human-specific Alu insertion. Conclusions This seemingly stealth-like amplification, ongoing at a very low rate over millions of years of evolution, suggests that this shared insertion may represent an ancient backseat driver of Alu element expansion.

A High-Performance Deformable Mirror with Integrated Driver ASIC for Space Based Active Optics

Science.gov (United States)

Shelton, Chris

Direct imaging of exoplanets is key to fully understanding these systems through spectroscopy and astrometry. The primary impediment to direct imaging of exoplanets is the extremely high brightness ratio between the planet and its parent star. Direct imaging requires a technique for contrast suppression, which include coronagraphs, and nulling interferometers. Deformable mirrors (DMs) are essential to both of these techniques. With space missions in mind, Microscale is developing a novel DM with direct integration of DM and its electronic control functions in a single small envelope. The Application Specific Integrated Circuit (ASIC) is key to the shrinking of the electronic control functions to a size compatible with direct integration with the DM. Through a NASA SBIR project, Microscale, with JPL oversight, has successfully demonstrated a unique deformable mirror (DM) driver ASIC prototype based on an ultra-low power switch architecture. Microscale calls this the Switch-Mode ASIC, or SM-ASIC, and has characterized it for a key set of performance parameters, and has tested its operation with a variety of actuator loads, such as piezo stack and unimorph, and over a wide temperature range. These tests show the SM-ASIC's capability of supporting active optics in correcting aberrations of a telescope in space. Microscale has also developed DMs to go with the SM-ASIC driver. The latest DM version produced uses small piezo stack elements in an 8x8 array, bonded to a novel silicon facesheet structure fabricated monolithically into a polished mirror on one side and mechanical linkage posts that connect to the piezoelectric stack actuators on the other. In this Supporting Technology proposal we propose to further develop the ASIC-DM and have assembled a very capable team to do so. It will be led by JPL, which has considerable expertise with DMs used in Adaptive Optics systems, with high-contrast imaging systems for exoplanet missions, and with designing DM driver

Advances of energy drivers at Osaka

International Nuclear Information System (INIS)

Kato, Yoshiaki; Nakai, Sadao; Yamanaka, Chiyoe.

1979-01-01

The energy driver development at the Institute of Laser Engineering (ILE), Osaka University, comprises three fields; glass, laser, carbon dioxide laser, and relativistic electron beam. The development of reliable glass lasers has been the main program at ILE. The GEKKO 12 module program was carried out in the fiscal years from 1977 to 1979 in order to develop various laser components and subsystems which are necessary to construct a 20 kJ GEKKO 12 glass laser. The measured gain coefficient of the 200 mm disk amplifier was 0.10/cm corresponding to the αD product of 4.0. The expected peak output power of the system was 2 TW at 0.1 ns and 0.9 kJ at 1 ns. The recent advances in coating techniques will enable to operate this system over 1.3 kJ per beam at 3 ns. Carbon dioxide lasers have been developed as efficient high energy lasers to study the wave length scaling of implosion process. The design and construction of the 10 kJ LEKKO 8 laser system are in progress. Relativistic electron beam machines, being the most cost-effective driver, have been studied to control pulsed power and to investigate electron beam plasma interaction. As the future plans of ILE, the construction of a 100 kJ energy driver from 1958 to 1987 for scientific break-even experiments is considered. (Kato, T.)

Value drivers: an approach for estimating health and disease management program savings.

Science.gov (United States)

Phillips, V L; Becker, Edmund R; Howard, David H

2013-12-01

Health and disease management (HDM) programs have faced challenges in documenting savings related to their implementation. The objective of this eliminate study was to describe OptumHealth's (Optum) methods for estimating anticipated savings from HDM programs using Value Drivers. Optum's general methodology was reviewed, along with details of 5 high-use Value Drivers. The results showed that the Value Driver approach offers an innovative method for estimating savings associated with HDM programs. The authors demonstrated how real-time savings can be estimated for 5 Value Drivers commonly used in HDM programs: (1) use of beta-blockers in treatment of heart disease, (2) discharge planning for high-risk patients, (3) decision support related to chronic low back pain, (4) obesity management, and (5) securing transportation for primary care. The validity of savings estimates is dependent on the type of evidence used to gauge the intervention effect, generating changes in utilization and, ultimately, costs. The savings estimates derived from the Value Driver method are generally reasonable to conservative and provide a valuable framework for estimating financial impacts from evidence-based interventions.

Volvo drivers' experiences with advanced crash avoidance and related technologies.

Science.gov (United States)

Eichelberger, Angela H; McCartt, Anne T

2014-01-01

Crash avoidance technologies can potentially prevent or mitigate many crashes, but their success depends in part on driver acceptance. Owners of 2010-2012 model Volvo vehicles with several technologies were interviewed about their experiences. Interviews were conducted in summer 2012 with 155 owners of vehicles with City Safety as a standard feature; 145 owners with an optional technology package that included adaptive cruise control, distance alert, collision warning with full auto brake (and pedestrian detection on certain models), driver alert control, and lane departure warning; and 172 owners with both City Safety and the technology package. The survey response rates were 21 percent for owners with City Safety, 30 percent for owners with the technology package, and 27 percent for owners with both. Ten percent of owners opted out before the telephone survey began, and 18 percent declined to participate when called. Despite some annoyance, most respondents always leave the systems on, although fewer do so for lane departure warning (59%). For each of the systems, at least 80 percent of respondents with the system would want it on their next vehicle. Many respondents reported safer driving habits with the systems (e.g., following less closely with adaptive cruise control, using turn signals more often with lane departure warning). Fewer respondents reported potentially unsafe behavior, such as allowing the vehicle to brake for them at least some of the time. About one third of respondents experienced autonomous braking when they believed they were at risk of crashing, and about one fifth of respondents thought it had prevented a crash. About one fifth of respondents with the technology package reported that they were confused or misunderstood which safety system had activated in their vehicle. Consistent with the results for early adopters in the previous survey of Volvo and Infiniti owners, the present survey found that driver acceptance of the technologies

Evaluation of a program to enhance young drivers' safety in Israel.

Science.gov (United States)

Toledo, Tomer; Lotan, Tsippy; Taubman-Ben-Ari, Orit; Grimberg, Einat

2012-03-01

Young drivers in Israel, as in other parts of the world, are involved in car crashes more than any other age group. The graduated driver licensing system in Israel requires that all new drivers be accompanied by an experienced driver whenever they drive for the first 3 months after obtaining a driving license. In an effort to make the accompanied driving phase more effective, a novel program which targets both young drivers and their parents was initiated in 2005. The program administers a personal meeting with the young driver and the accompanying parent scheduled for the beginning of the accompanied driving phase. In this meeting guidance is given regarding best practices for undertaking the accompanied driving, as well as tips for dealing with in-vehicle parent-teen dynamics. Through 2008, almost 130,000 families of young drivers have participated in the program. In order to evaluate the effectiveness of the program, injury crash records of the young drivers who participated in the program were compared with those of all other young drivers that were licensed at the same time period. The results obtained indicate statistically significant lower crash records for young drivers that participated in the program. Limitations of the evaluation related to self-selection biases are discussed, and practical implications are suggested. Copyright © 2011 Elsevier Ltd. All rights reserved.

Evaluation of advanced driver assistance system with the VEHIL test facility: experiences and future developments at TNO automotive

NARCIS (Netherlands)

Kusters, L.J.J.; Gietelink, O.J.; Hoof, J.F.A.M. van; Lemmen, P.P.M.

2004-01-01

This paper presents the working principle, functionality and the experience during the first operational period of the VEHIL laboratory, dedicated to the development and testing of advanced driver assistance systems. The position of VEHIL and its PC based full software variant PRESCAN is illustrated

Cognitive characteristics of older Japanese drivers.

Science.gov (United States)

Susilowati, Indri H; Yasukouchi, Akira

2012-02-29

Some causes of accidents among older drivers are: not paying attention to traffic signals; missing stop lines; and having to deal with and misjudging emergency situations. These causes of accidents reveal problems with attention and cognition. Such incidents are also related to driver perception and stress-coping mechanisms. It is important to examine the relation of stress reactions to attention and cognition as a factor influencing the causes of accidents commonly involving older drivers. Subjects were 10 young drivers (23.3 ± 3.33 years) and 25 older drivers divided into two groups (older1 [60 to 65 years] and older2 [> 65 years]). This study revealed the correlation within driver stress inventory and driver coping questionnaires parameters was observed only in older drivers. They also needed a longer response time for Trail Making Test A and B. The factors affected the attention and cognition of older drivers by age but not driving experience itself, and coping parameters such as emotion focus, reappraisal, and avoidance were not included as stress inventory parameters. Being prone to fatigue was less for younger drivers than older drivers. Because they have shorter distances, shorter drive times, and no need for expressways, older drivers also had a significantly lower risk of thrill-seeking behaviour and more patience. The intervention addressing their attention skills, aggressive feelings, and emotion focus should be considered. The technological improvements in cars will make older drivers feel safer and make driving easier which might lower the attention paid to the road, and regular driving training might be needed to assess and enhance their safety.

A Test Device Module of the Step Motor Driver for HANARO CAR Operation

Energy Technology Data Exchange (ETDEWEB)

Im, Yun-Taek; Doo, Seung-Gyu; Shin, Jin-Won; Kim, Ki-Hyun; Choi, Young-San; Lee, Jung-Hee; Kim, Hyung-Kyoo; Lee, Choong-Sung [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2016-10-15

The brand-new control system is reliable and has advantages compared with the old control system, and the installed system covers all functional operations of old system. Nevertheless, packaged RTP systems do not include a step motor or driver, and it is necessary to develop a proper test device to check the step motor and driver without using the RTP system. In particular, the operation of a CAR (Control Absorber Rod) requires many complicated procedures. Occasionally, it takes significant time to prepare for a field test. In this work, a test device module for a step motor diver is shown to emulate a HANARO CAR operation, and the test device system architecture, operational principle, and experiment results are presented. A commercial 8-bit μ-processor is applied to implement the device. A portable test device for HANARO CAR operation is presented. An 8-bit μ-controller is used to emulate a HANARO CAR operation. The digital interface, as well as the functional operation, of the test device module matches that of the currently used driver. This device can be used to check the functional validity of the step motor and driver.

Drug involvement of fatally injured drivers

Science.gov (United States)

2010-11-01

While data focusing on the danger of driving under the influence : of alcohol is readily available and often cited, less is : known or discussed about drivers under the influence of : other drugs. The Fatality Analysis Reporting System (FARS), : a ce...

Training of Drivers in the Function of Road Traffic Safety

Directory of Open Access Journals (Sweden)

Sinan Alispahić

2007-09-01

Full Text Available The problem of the participation of young drivers in trafficaccidents is constantly present and represents a significant socialproblem. In complex and dynamic conditions of moderntraffic flows, the young drivers are exposed to various and unforeseenhazard situations and events which they had not experiencedduring the basic training. Therefore, they should be providedwith the possibility of acquiring additional experiences insolving typical hazard situations in traffic. This is possible bythe system of advanced training which places the course participantin the situation of facing possible hazards, with the aim ofincreasing the awareness of risk in driving and behaviour at thesteering wheel. Advanced driver training is based on the specificprogram and training the drivers to acquire additional experiencesin solving dangerous traffic situations.

Stimulus driver for epilepsy seizure suppression with adaptive loading impedance

Science.gov (United States)

Ker, Ming-Dou; Lin, Chun-Yu; Chen, Wei-Ling

2011-10-01

A stimulus driver circuit for a micro-stimulator used in an implantable device is presented in this paper. For epileptic seizure control, the target of the driver was to output 30 µA stimulus currents when the electrode impedance varied between 20 and 200 kΩ. The driver, which consisted of the output stage, control block and adaptor, was integrated in a single chip. The averaged power consumption of the stimulus driver was 0.24-0.56 mW at 800 Hz stimulation rate. Fabricated in a 0.35 µm 3.3 V/24 V CMOS process and applied to a closed-loop epileptic seizure monitoring and controlling system, the proposed design has been successfully verified in the experimental results of Long-Evans rats with epileptic seizures.

Combining coordination of motion actuators with driver steering interaction.

Science.gov (United States)

Tagesson, Kristoffer; Laine, Leo; Jacobson, Bengt

2015-01-01

A new method is suggested for coordination of vehicle motion actuators; where driver feedback and capabilities become natural elements in the prioritization. The method is using a weighted least squares control allocation formulation, where driver characteristics can be added as virtual force constraints. The approach is in particular suitable for heavy commercial vehicles that in general are over actuated. The method is applied, in a specific use case, by running a simulation of a truck applying automatic braking on a split friction surface. Here the required driver steering angle, to maintain the intended direction, is limited by a constant threshold. This constant is automatically accounted for when balancing actuator usage in the method. Simulation results show that the actual required driver steering angle can be expected to match the set constant well. Furthermore, the stopping distance is very much affected by this set capability of the driver to handle the lateral disturbance, as expected. In general the capability of the driver to handle disturbances should be estimated in real-time, considering driver mental state. By using the method it will then be possible to estimate e.g. stopping distance implied from this. The setup has the potential of even shortening the stopping distance, when the driver is estimated as active, this compared to currently available systems. The approach is feasible for real-time applications and requires only measurable vehicle quantities for parameterization. Examples of other suitable applications in scope of the method would be electronic stability control, lateral stability control at launch and optimal cornering arbitration.

Decision support systems

DEFF Research Database (Denmark)

Jørgensen, L.N.; Noe, E.; Langvad, A.M.

2007-01-01

system Crop Protection Online is widely used by advisors and as a learning tool for students. Although the system has been validated in many field trials over the years and has shown reliable results, the number of end-users among farmers has been relatively low during the last 10 years (approximately...... 1000 farmers). A sociological investigation of farmers' decision-making styles in the area of crop protection has shown that arable farmers can be divided into three major groups: (a) system-orientated farmers, (b) experience-based farmers and (c) advisory-orientated farmers. The information required...... by these three groups to make their decisions varies and therefore different ways of using decision support systems need to be provided. Decision support systems need to be developed in close dialogue and collaboration with user groups....

Leptospirosis in American Samoa 2010: epidemiology, environmental drivers, and the management of emergence.