Enhanced transconductance in a double-gate graphene field-effect transistor

Science.gov (United States)

Hwang, Byeong-Woon; Yeom, Hye-In; Kim, Daewon; Kim, Choong-Ki; Lee, Dongil; Choi, Yang-Kyu

2018-03-01

Multi-gate transistors, such as double-gate, tri-gate and gate-all-around transistors are the most advanced Si transistor structure today. Here, a genuine double-gate transistor with a graphene channel is experimentally demonstrated. The top and bottom gates of the double-gate graphene field-effect transistor (DG GFET) are electrically connected so that the conductivity of the graphene channel can be modulated simultaneously by both the top and bottom gate. A single-gate graphene field-effect transistor (SG GFET) with only the top gate is also fabricated as a control device. For systematical analysis, the transfer characteristics of both GFETs were measured and compared. Whereas the maximum transconductance of the SG GFET was 17.1 μS/μm, that of the DG GFET was 25.7 μS/μm, which is approximately a 50% enhancement. The enhancement of the transconductance was reproduced and comprehensively explained by a physics-based compact model for GFETs. The investigation of the enhanced transfer characteristics of the DG GFET in this work shows the possibility of a multi-gate architecture for high-performance graphene transistor technology.

Succeeding at the Bottom-of-the-Pyramid

DEFF Research Database (Denmark)

Boxenbaum, Eva; Olsen, Mette

initiative to build a social impact venture at the interface of a multi-national corporation and a hybrid organization that is operating on the Bottom-of-the-Pyramid market. Our study identifies how corporate social entrepreneurs dynamically use framing and organizational anchoring strategies to build...... ventures in the double pursuit of financial objectives and wider societal objectives. Through an empirical study, we investigate the strategies and practices that corporate social entrepreneurs employ to build radically new social ventures outside their firm. More specifically, we examine a successful......Hybrid organizational forms often rely on the initiative or collaboration of corporate actors, yet the role of these actors is rarely examined in detail. This paper examines corporate social entrepreneurship, which refers to the initiative of corporate actors to establish new, independent social...

Cylinder-type bottom reflector

International Nuclear Information System (INIS)

Elter, C.; Fritz, R.; Kissel, K.F.; Schoening, J.

1982-01-01

Proposal of a bottom reflector for gas-cooled nuclear reactor plants with a pebble bed of spherical fuel elements, where the horizontal forces acting from the core and the bottom reflector upon the side reflector are equally distributed. This is attained by the upper edge of the bottom reflector being placed levelly and by the angle of inclination of the recesses varying. (orig.) [de

Reinforcement mechanism of multi-anchor wall with double wall facing

Science.gov (United States)

Suzuki, Kouta; Kobayashi, Makoto; Miura, Kinya; Konami, Takeharu; Hayashi, Taketo

2017-10-01

The reinforced soil wall has high seismic performance as generally known. However, the seismic behavior has not been clarified accurately yet, especially on multi-anchor wall with double wall facing. Indefinite behavior of reinforced soil wall during earthquake make us complicated in case with adopting to the abutment, because of arrangement of anchor plate as reinforcement often different according to the width of roads. In this study, a series of centrifuge model tests were carried out to investigate the reinforcement mechanism of multi anchor wall with double wall facing from the perspective of the vertical earth pressure. Several types of reinforce arrangement and rigid wall were applied in order to verify the arch function in the reinforced regions. The test results show unique behavior of vertical earth pressure, which was affected by arch action. All the vertical earth pressure placed behind facing panel, are larger than that of middle part between facing panel despite of friction between backfill and facing panel. Similar results were obtained in case using rigid wall. On the other hands, the vertical earth pressure, which were measured at the 3cm high from bottom of model container, shows larger than that of bottom. This results show the existence of arch action between double walls. In addition, it implies that the wall facing of such soil structure confined the backfill as pseudo wall, which is very reason that the multi anchor wall with double wall facing has high seismic performance.

Bottom friction models for shallow water equations: Manning’s roughness coefficient and small-scale bottom heterogeneity

Science.gov (United States)

Dyakonova, Tatyana; Khoperskov, Alexander

2018-03-01

The correct description of the surface water dynamics in the model of shallow water requires accounting for friction. To simulate a channel flow in the Chezy model the constant Manning roughness coefficient is frequently used. The Manning coefficient nM is an integral parameter which accounts for a large number of physical factors determining the flow braking. We used computational simulations in a shallow water model to determine the relationship between the Manning coefficient and the parameters of small-scale perturbations of a bottom in a long channel. Comparing the transverse water velocity profiles in the channel obtained in the models with a perturbed bottom without bottom friction and with bottom friction on a smooth bottom, we constructed the dependence of nM on the amplitude and spatial scale of perturbation of the bottom relief.

Performance of an X-ray spectroscopic system based on a double-gate double-feedback charge preamplifier

CERN Document Server

Fazzi, A

2000-01-01

The performance of a near room temperature X-ray spectroscopic system is reported. The system is based on a charge preamplifier with the first transistor having two separated gates. The preamplifier operates in a continuous reset mode without any physical resistor connected to the input node. The leakage current and the current due to the rate of X-rays is neutralized by an average current of holes, flowing under the control of an additional feedback, from the bottom to the top gate. The preamplifier is followed by a simple circuit which exactly cancels the long tail of the impulse response of a pure double-gate preamplifier. The compensation of this tail, due to the very principle of the preamplifier's continuous reset through the double-gate mechanism, improves substantially the high-rate performance of the system. The preamplifier based on a commercially available double-gate front JFET MX-40 (MOXTEK) coupled to a silicon drift detector produced at BNL achieved ENC of 13 electrons at -30 deg. C. The analys...

Bottom-linked innovation

DEFF Research Database (Denmark)

Kristensen, Catharina Juul

2018-01-01

hitherto been paid little explicit attention, namely collaboration between middle managers and employees in innovation processes. In contrast to most studies, middle managers and employees are here both subjects of explicit investigation. The collaboration processes explored in this article are termed...... ‘bottom-linked innovation’. The empirical analysis is based on an in-depth qualitative study of bottom-linked innovation in a public frontline institution in Denmark. By combining research on employee-driven innovation and middle management, the article offers new insights into such collaborative......Employee-driven innovation is gaining ground as a strategy for developing sustainable organisations in the public and private sector. This type of innovation is characterised by active employee participation, and the bottom-up perspective is often emphasised. This article explores an issue that has...

Hybrid Dye-Sensitized Solar Cells Consisting of Double Titania Layers for Harvesting Light with Wide Range of Wavelengths

Science.gov (United States)

Sadamasu, Kengo; Inoue, Takafumi; Ogomi, Yuhei; Pandey, Shyam S.; Hayase, Shuzi

2011-02-01

We report a hybrid dye-sensitized solar cell consisting of double titania layers (top and bottom layers) stained with two dyes. A top layer fabricated on a glass was mechanically pressed with a bottom layer fabricated on a glass cloth. The glass cloth acts as a supporter of a porous titania layer as well as a holder of electrolyte. The incident photon to current efficiency (IPCE) curve had two peaks corresponding to those of the two dyes, which demonstrates that electrons are collected from both the top and bottom layers.

The Bottom Boundary Layer.

Science.gov (United States)

Trowbridge, John H; Lentz, Steven J

2018-01-03

The oceanic bottom boundary layer extracts energy and momentum from the overlying flow, mediates the fate of near-bottom substances, and generates bedforms that retard the flow and affect benthic processes. The bottom boundary layer is forced by winds, waves, tides, and buoyancy and is influenced by surface waves, internal waves, and stratification by heat, salt, and suspended sediments. This review focuses on the coastal ocean. The main points are that (a) classical turbulence concepts and modern turbulence parameterizations provide accurate representations of the structure and turbulent fluxes under conditions in which the underlying assumptions hold, (b) modern sensors and analyses enable high-quality direct or near-direct measurements of the turbulent fluxes and dissipation rates, and (c) the remaining challenges include the interaction of waves and currents with the erodible seabed, the impact of layer-scale two- and three-dimensional instabilities, and the role of the bottom boundary layer in shelf-slope exchange.

The Bottom Boundary Layer

Science.gov (United States)

Trowbridge, John H.; Lentz, Steven J.

2018-01-01

The oceanic bottom boundary layer extracts energy and momentum from the overlying flow, mediates the fate of near-bottom substances, and generates bedforms that retard the flow and affect benthic processes. The bottom boundary layer is forced by winds, waves, tides, and buoyancy and is influenced by surface waves, internal waves, and stratification by heat, salt, and suspended sediments. This review focuses on the coastal ocean. The main points are that (a) classical turbulence concepts and modern turbulence parameterizations provide accurate representations of the structure and turbulent fluxes under conditions in which the underlying assumptions hold, (b) modern sensors and analyses enable high-quality direct or near-direct measurements of the turbulent fluxes and dissipation rates, and (c) the remaining challenges include the interaction of waves and currents with the erodible seabed, the impact of layer-scale two- and three-dimensional instabilities, and the role of the bottom boundary layer in shelf-slope exchange.

Investigation of InGaN/Si double junction tandem solar cells | Bouzid ...

African Journals Online (AJOL)

In this work, the solar power conversion efficiency of InGaN/Si double junction tandem solar cells was investigated under 1-sun AM1.5 illumination, using realistic material parameters. With this intention, the current-voltage curves are calculated for different front recombination velocities and the influence of the bottom cell ...

Modelling of the bending behaviour of double floor systems for different contact surfaces

Directory of Open Access Journals (Sweden)

Attila PUSKAS

2014-07-01

Full Text Available In the practice of prefabricated concrete structures considerable surfaces of intermediate floors are constructed using double floor systems with prefabricated bottom layer and upper layer. This second layer is cast on site. The quality of the prefabricated concrete is often of superior class with respect to the monolithic layer. In the service state of the double floor system, important compressive stresses appear in the upper concrete layer. On the other hand, the bond quality between the concrete layers cast in successive stages raises questions especially in the case of hollow core floor units with no connecting reinforcement in-between. The paper presents results of the numerical models prepared for double floor elements having different thicknesses for the top and bottom layers, subjected to bending. Three situations have been studied: stepped top surface of the prefabricated slab with no connecting reinforcement, broom swept tracks on the prefabricated slab with no connecting reinforcement and broom swept tracks on the prefabricated slab with stirrups connecting the concrete layers. For each situation two different ratios of the thicknesses of the layers have been considered. The results are emphasizing the critical regions of the elements, the differences in crack development and in the behaviour resulting from surface preparation and use of connecting reinforcements.

Far-field tsunami magnitude determined from ocean-bottom pressure gauge data around Japan

Science.gov (United States)

Baba, T.; Hirata, K.; Kaneda, Y.

2003-12-01

doubled by reflection at the fixed edge (coastline). Hence, we introduce a water-depth term and a reflection coefficient of 2 in the original Abe_fs empirical relation to correct tsunami amplitude for open oceans and obtain Mt = log(2H/h-1/4) + 9.1, where h is the depth of the ocean bottom pressure gage. The modified empirical relation produces tsunami magnitudes close to those determined using tide gauges.

ELECTROCHEMICAL STUDIES OF CARBON STEEL CORROSION IN HANFORD DOUBLE SHELL TANK (DST) WASTE

Energy Technology Data Exchange (ETDEWEB)

DUNCAN, J.B.; WINDISCH, C.F.

2006-10-13

This paper reports on the electrochemical scans for the supernatant of Hanford double-shell tank (DST) 241-SY-102 and the electrochemical scans for the bottom saltcake layer for Hanford DST 241-AZ-102. It further reports on the development of electrochemical test cells adapted to both sample volume and hot cell constraints.

Pressing technology for large bottoms

International Nuclear Information System (INIS)

Jilek, L.

1986-01-01

The technology has been selected of a circular plate bent into the shape of a trough, for pressing bottoms of pressure vessels from a circular plate of large diameter. The initial sheet is first bent in the middle by heating with the edges remaining straight. These are then welded longitudinally by electroslag welding and the circular shape is flame cut. The result will be a plate with a straight surface in the middle with raised edges which may be pressed into the desired shape. In this manner it is also possible to press pressure vessel bottoms with tube couplings from plates which are thickened in the middle and drilled; additional welding is then eliminated. Deformation from heat treatment may be avoided by the use of a fixture in the shape of a ring with a groove into which is fixed the edge of the bottom. During hardening of the bottom it will be necessary to care for the withdrawal of vapours and gases which would hamper uniform cooling. Bottom hardening with the grill and the cupola downwards has been proven. Deformation which occurs during treatment may to a certain extent be removed by calibration which cannot, however, be made without special fixtures and instruments. (J.B.)

Making the results of bottom-up energy savings comparable

Directory of Open Access Journals (Sweden)

Moser Simon

2012-01-01

Full Text Available The Energy Service Directive (ESD has pushed forward the issue of energy savings calculations without clarifying the methodological basis. Savings achieved in the Member States are calculated with rather non-transparent and hardly comparable Bottom-up (BU methods. This paper develops the idea of parallel evaluation tracks separating the Member States’ issue of ESD verification and comparable savings calculations. Comparability is ensured by developing a standardised BU calculation kernel for different energy efficiency improvement (EEI actions which simultaneously depicts the different calculation options in a structured way (e.g. baseline definition, system boundaries, double counting. Due to the heterogeneity of BU calculations the approach requires a central database where Member States feed in input data on BU actions according to a predefined structure. The paper demonstrates the proposed approach including a concrete example of application.

Rita Bottoms: Polyartist Librarian

OpenAIRE

Bottoms, Rita; Reti, Irene; Regional History Project, UCSC Library

2005-01-01

Project Director Irene Reti conducted fourteen hours of interviews with Rita Bottoms, Head of Special Collections at the University Library, UC Santa Cruz, shortly before her retirement in March 2003. This oral history provides a vivid and intimate look at thirty-seven years behind the scenes in the library's Special Collections. For thirty-seven years Bottoms dedicated herself to collecting work by some of the most eminent writers and photographers of the twentieth century, includin...

Shallow flows with bottom topography

NARCIS (Netherlands)

Heijst, van G.J.F.; Kamp, L.P.J.; Theunissen, R.; Rodi, W.; Uhlmann, M.

2012-01-01

This paper discusses laboratory experiments and numerical simulations of dipolar vortex flows in a shallow fluid layer with bottom topography. Two cases are considered: a step topography and a linearly sloping bottom. It is found that viscous effects – i.e., no-slip conditions at the non-horizontal

Measurement of the bottom hadron lifetime at the Z0 resonancce

International Nuclear Information System (INIS)

Fujino, D.H.

1992-06-01

We have measured the bottom hadron lifetime from b bar b events produced at the Z 0 resonance. Using the precision vertex detectors of the Mark II detector at the Stanford Linear Collider, we developed an impact parameter tag to identify bottom hadrons. The vertex tracking system resolved impact parameters to 30 μm for high momentum tracks, and 70 μm for tracks with a momentum of 1 GeV. We selected B hadrons with an efficiency of 40% and a sample purity of 80%, by requiring there be at least two tracks in a single jet that significantly miss the Z 0 decay vertex. From a total of 208 hadronic Z 0 events collected by the Mark II detector in 1990, we tagged 53 jets, of which 22 came from 11 double-tagged events. The jets opposite the tagged ones, referred as the ''untagged'' sample, are rich in B hadrons and unbiased in B decay times. The variable Σδ is the sum of impact parameters from tracks in the jet, and contains vital information on the B decay time. We measured the B lifetime from a one-parameter likelihood fit to the untagged Σδ distribution, obtaining τ b = 1.53 -0.45 +0.55 ±0.16 ps which agrees with the current world average. The first error is statistical and the second is systematic. The systematic error was dominated by uncertainties in the track resolution function. As a check, we also obtained consistent results using the Σδ distribution from the tagged jets and from the entire hadronic sample without any bottom enrichment

Final results of double-shell tank 241-AN-105 ultrasonic inspection

International Nuclear Information System (INIS)

JENSEN, C.E.

1999-01-01

This document presents the results and documentation of the nondestructive ultrasonic examination of tank 241-AN-105. A tank inspection supplier was retained to provide and use an ultrasonic examination system (equipment, procedures, and inspectors) to scan a limited area of double-shell tank 241-AN-105 primary tank wall primary knuckle, and secondary tank bottom. The inspection found some indication of general and local wall thinning with no cracks detected

Ship with a double hull used to transport liquefied gases

Energy Technology Data Exchange (ETDEWEB)

1968-07-18

A ship with a double hull is described which is used to transport liquefied gases in reservoirs which are held inside the inner hull by a glide support and surrounded by insulation. Troughs are situated at the bottom and along the adjacent ends of the side walls to catch leakage from the reservoirs. These catchers are made of a material which is tough when chilled. The catchers have a suction installation to remove the leaked fluid. (5 claims)

Core design of super LWR with double tube water rods

International Nuclear Information System (INIS)

Wu, Jianhui; Oka, Yoshiaki

2014-01-01

Highlights: • Supercritical light water cooled and moderated reactor with double tube water rods is developed. • Double-row fuel rod assembly and out-in fuel loading pattern are applied. • Separation plates in peripheral assemblies increase average outlet temperature. • Neutronic and thermal design criteria are satisfied during the cycle. - Abstract: Double tube water rods are employed in core design of super LWR to simplify the upper core structure and refueling procedure. The light water moderator flows up in the inner tube from the bottom of the core, then, changes the flow direction at the top of the core into the outer tube and flows out at the bottom of the core. It eliminates the moderator guide/distribution tubes into the single tube water rods from the top dome of the reactor pressure vessel of the previous super LWR design. Two rows of fuel rods are filled between the water rods in the fuel assembly. Out-in refueling pattern is adopted to flatten radial power distribution. The peripheral fuel assemblies of the core are divided into four flow zones by separation plates for increasing the average core outlet temperature. Three enrichment zones are used for axial power flattening. The equilibrium core is analyzed based on neutronic/thermal-hydraulic coupled model. The results show that, by applying the separation plates in peripheral fuel assemblies and low gadolinia enrichment, the maximum cladding surface temperature (MCST) is limited to 653 °C with the average outlet temperature of 500 °C. The inherent safety is satisfied by the negative void reactivity effects and sufficient shutdown margin

Measurement of the bottom hadron lifetime at the Z sup 0 resonancce

Energy Technology Data Exchange (ETDEWEB)

Fujino, D.H.

1992-06-01

We have measured the bottom hadron lifetime from b{bar b} events produced at the Z{sup 0} resonance. Using the precision vertex detectors of the Mark II detector at the Stanford Linear Collider, we developed an impact parameter tag to identify bottom hadrons. The vertex tracking system resolved impact parameters to 30 {mu}m for high momentum tracks, and 70 {mu}m for tracks with a momentum of 1 GeV. We selected B hadrons with an efficiency of 40% and a sample purity of 80%, by requiring there be at least two tracks in a single jet that significantly miss the Z{sup 0} decay vertex. From a total of 208 hadronic Z{sup 0} events collected by the Mark II detector in 1990, we tagged 53 jets, of which 22 came from 11 double-tagged events. The jets opposite the tagged ones, referred as the untagged'' sample, are rich in B hadrons and unbiased in B decay times. The variable {Sigma}{delta} is the sum of impact parameters from tracks in the jet, and contains vital information on the B decay time. We measured the B lifetime from a one-parameter likelihood fit to the untagged {Sigma}{delta} distribution, obtaining {tau}{sub b} = 1.53{sub {minus}0.45}{sup +0.55}{plus minus}0.16 ps which agrees with the current world average. The first error is statistical and the second is systematic. The systematic error was dominated by uncertainties in the track resolution function. As a check, we also obtained consistent results using the {Sigma}{delta} distribution from the tagged jets and from the entire hadronic sample without any bottom enrichment.

Double-layer structure in polar mesospheric clouds observed from SOFIE/AIM

Directory of Open Access Journals (Sweden)

H. Gao

2017-02-01

Full Text Available Double-layer structures in polar mesospheric clouds (PMCs are observed by using Solar Occultation for Ice Experiment (SOFIE data between 2007 and 2014. We find 816 and 301 events of double-layer structure with percentages of 10.32 and 7.25 % compared to total PMC events, and the mean distances between two peaks are 3.06 and 2.73 km for the Northern Hemisphere (NH and Southern Hemisphere (SH respectively. Double-layer PMCs almost always have less mean ice water content (IWC than daily IWC during the core of the season, but they are close to each other at the beginning and the end. The result by averaging over all events shows that the particle concentration has obvious double peaks, while the particle radius exhibits an unexpected monotonic increase with decreasing altitude. By further analysis of the background temperature and water vapour residual profiles, we conclude that the lower layer is a reproduced one formed at the bottom of the upper layer. 56.00 and 47.51 % of all double-layer events for the NH and SH respectively have temperature enhancements larger than 2 K locating between their double peaks. The longitudinal anti-correlation between the gravity waves' (GWs' potential energies and occurrence frequencies of double-layer PMCs suggests that the double-layer PMCs tend to form in an environment where the GWs have weaker intensities.

Simulation of double-seaming in a two-piece aluminum can

International Nuclear Information System (INIS)

Romanko, Anne; Berry, Dale; Fox, David

2004-01-01

The aluminum can industry in the United States and Canada manufactures over 100 billion cans per year. Two-piece aluminum cans are commonly used to seal and deliver foodstuffs such as soft drinks, beer, pet food, and other perishable items. In order to ensure product safety and performance, the double seam between the can body and lid is a critical component of the package. Double-seaming is a method by which the flange of the can body and the curl of the end are folded over together such that the final joint is composed of five metal thicknesses. There are a number of design challenges involved with the art of double seaming, especially with the push to lightweight. Although the requirements vary by product, the typical beer package must be able to hold pressures in excess of 90psi. In addition, in production, double seaming is a high-speed operation with speeds as high as 3000 cans/minute on an 18-spindle seamer. For this high volume, low cost industry, understanding and optimizing the seaming process can advance the industry as well as help prevent various manufacturing problems that produce a poor seal between the two pieces of the can.To aid in understanding the mechanics of the can parts during double-seaming, a simulation procedure was developed and carried out on a 202 diameter beverage can and lid. Simulations were run with the explicit dynamics solver ABAQUS/Explicit using the continuum shell element technology available in the ABAQUS general purpose FEA program. The continuum shell is a shear-deformable shell element with the topology of an eight node brick. The element's formulation allows continuously varying, solution-dependent shell thickness and through-thickness pinching stress. One important advantage of using the continuum shell as opposed to a traditional shell element is that true contact interactions at the top and bottom surfaces of the can body and lid can be accurately modeled. With a conventional shell element, contact is performed at the

Simulation of Double-Seaming in a Two-piece Aluminum Can

Science.gov (United States)

Romanko, Anne; Berry, Dale; Fox, David

2004-06-01

The aluminum can industry in the United States and Canada manufactures over 100 billion cans per year. Two-piece aluminum cans are commonly used to seal and deliver foodstuffs such as soft drinks, beer, pet food, and other perishable items. In order to ensure product safety and performance, the double seam between the can body and lid is a critical component of the package. Double-seaming is a method by which the flange of the can body and the curl of the end are folded over together such that the final joint is composed of five metal thicknesses. There are a number of design challenges involved with the art of double seaming, especially with the push to lightweight. Although the requirements vary by product, the typical beer package must be able to hold pressures in excess of 90psi. In addition, in production, double seaming is a high-speed operation with speeds as high as 3000 cans/minute on an 18-spindle seamer. For this high volume, low cost industry, understanding and optimizing the seaming process can advance the industry as well as help prevent various manufacturing problems that produce a poor seal between the two pieces of the can. To aid in understanding the mechanics of the can parts during double-seaming, a simulation procedure was developed and carried out on a 202 diameter beverage can and lid. Simulations were run with the explicit dynamics solver ABAQUS/Explicit using the continuum shell element technology available in the ABAQUS general purpose FEA program. The continuum shell is a shear-deformable shell element with the topology of an eight node brick. The element's formulation allows continuously varying, solution-dependent shell thickness and through-thickness pinching stress. One important advantage of using the continuum shell as opposed to a traditional shell element is that true contact interactions at the top and bottom surfaces of the can body and lid can be accurately modeled. With a conventional shell element, contact is performed at the

Measurement of the bottom hadron lifetime at the Z⁰ resonancce

Energy Technology Data Exchange (ETDEWEB)

Fujino, Donald Hideo [Stanford Univ., CA (United States)

1992-06-01

We have measured the bottom hadron lifetime from b$\\bar{b}$ events produced at the Z⁰ resonance. Using the precision vertex detectors of the Mark II detector at the Stanford Linear Collider, we developed an impact parameter tag to identify bottom hadrons. The vertex tracking system resolved impact parameters to 30 μm for high momentum tracks, and 70 μm for tracks with a momentum of 1 GeV. We selected B hadrons with an efficiency of 40% and a sample purity of 80%, by requiring there be at least two tracks in a single jet that significantly miss the Z⁰ decay vertex. From a total of 208 hadronic Z⁰ events collected by the Mark II detector in 1990, we tagged 53 jets, of which 22 came from 11 double-tagged events. The jets opposite the tagged ones, referred as the ``untagged`` sample, are rich in B hadrons and unbiased in B decay times. The variable Σδ is the sum of impact parameters from tracks in the jet, and contains vital information on the B decay time. We measured the B lifetime from a one-parameter likelihood fit to the untagged Σδ distribution, obtaining τ_b = 1.53 $+0.55\\atop{-0.45}$ ± 0.16 ps which agrees with the current world average. The first error is statistical and the second is systematic. The systematic error was dominated by uncertainties in the track resolution function. As a check, we also obtained consistent results using the Σδ distribution from the tagged jets and from the entire hadronic sample without any bottom enrichment.

Top-Down Beta Enhances Bottom-Up Gamma.

Science.gov (United States)

Richter, Craig G; Thompson, William H; Bosman, Conrado A; Fries, Pascal

2017-07-12

Several recent studies have demonstrated that the bottom-up signaling of a visual stimulus is subserved by interareal gamma-band synchronization, whereas top-down influences are mediated by alpha-beta band synchronization. These processes may implement top-down control of stimulus processing if top-down and bottom-up mediating rhythms are coupled via cross-frequency interaction. To test this possibility, we investigated Granger-causal influences among awake macaque primary visual area V1, higher visual area V4, and parietal control area 7a during attentional task performance. Top-down 7a-to-V1 beta-band influences enhanced visually driven V1-to-V4 gamma-band influences. This enhancement was spatially specific and largest when beta-band activity preceded gamma-band activity by ∼0.1 s, suggesting a causal effect of top-down processes on bottom-up processes. We propose that this cross-frequency interaction mechanistically subserves the attentional control of stimulus selection. SIGNIFICANCE STATEMENT Contemporary research indicates that the alpha-beta frequency band underlies top-down control, whereas the gamma-band mediates bottom-up stimulus processing. This arrangement inspires an attractive hypothesis, which posits that top-down beta-band influences directly modulate bottom-up gamma band influences via cross-frequency interaction. We evaluate this hypothesis determining that beta-band top-down influences from parietal area 7a to visual area V1 are correlated with bottom-up gamma frequency influences from V1 to area V4, in a spatially specific manner, and that this correlation is maximal when top-down activity precedes bottom-up activity. These results show that for top-down processes such as spatial attention, elevated top-down beta-band influences directly enhance feedforward stimulus-induced gamma-band processing, leading to enhancement of the selected stimulus. Copyright © 2017 Richter, Thompson et al.

Bottom-up guidance in visual search for conjunctions.

Science.gov (United States)

Proulx, Michael J

2007-02-01

Understanding the relative role of top-down and bottom-up guidance is crucial for models of visual search. Previous studies have addressed the role of top-down and bottom-up processes in search for a conjunction of features but with inconsistent results. Here, the author used an attentional capture method to address the role of top-down and bottom-up processes in conjunction search. The role of bottom-up processing was assayed by inclusion of an irrelevant-size singleton in a search for a conjunction of color and orientation. One object was uniquely larger on each trial, with chance probability of coinciding with the target; thus, the irrelevant feature of size was not predictive of the target's location. Participants searched more efficiently for the target when it was also the size singleton, and they searched less efficiently for the target when a nontarget was the size singleton. Although a conjunction target cannot be detected on the basis of bottom-up processing alone, participants used search strategies that relied significantly on bottom-up guidance in finding the target, resulting in interference from the irrelevant-size singleton.

MOSFET-based high voltage double square-wave pulse generator with an inductive adder configuration

Energy Technology Data Exchange (ETDEWEB)

Zhao, Xin [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Zhang, Qiaogen, E-mail: hvzhang@mail.xjtu.edu.cn [State Key Laboratory of Electrical Insulation and Power Equipment, Xi' an Jiaotong University, Xi' an 710049 (China); Long, Jinghua [College of Physics, Shenzhen University, Shenzhen 518060 (China); Lei, Yunfei; Liu, Jinyuan [Institute of Optoelectronics, Shenzhen University, Shenzhen 518060 (China)

2015-09-01

This paper presents a fast MOSFET-based solid-state pulse generator for high voltage double square-wave pulses. The generator consists mainly of an inductive adder system stacked of 20 solid-state modules. Each of the modules has 18 power MOSFETs in parallel, which are triggered by individual drive circuits; these drive circuits themselves are synchronously triggered by a signal from avalanche transistors. Our experiments demonstrate that the output pulses with amplitude of 8.1 kV and peak current of about 405 A are available at a load impedance of 20 Ω. The pulse has a double square-wave form with a rise and fall time of 40 ns and 26 ns, respectively and bottom flatness better than 12%. The interval time of the double square-wave pulses can be adjustable by varying the interval time of the trigger pulses.

Analysis of Maisotsenko open gas turbine bottoming cycle

International Nuclear Information System (INIS)

Saghafifar, Mohammad; Gadalla, Mohamed

2015-01-01

Maisotsenko gas turbine cycle (MGTC) is a recently proposed humid air turbine cycle. An air saturator is employed for air heating and humidification purposes in MGTC. In this paper, MGTC is integrated as the bottoming cycle to a topping simple gas turbine as Maisotsenko bottoming cycle (MBC). A thermodynamic optimization is performed to illustrate the advantages and disadvantages of MBC as compared with air bottoming cycle (ABC). Furthermore, detailed sensitivity analysis is reported to present the effect of different operating parameters on the proposed configurations' performance. Efficiency enhancement of 3.7% is reported which results in more than 2600 tonne of natural gas fuel savings per year. - Highlights: • Developed an accurate air saturator model. • Introduced Maisotsenko bottoming cycle (MBC) as a power generation cycle. • Performed Thermodynamic optimization for MBC and air bottoming cycle (ABC). • Performed detailed sensitivity analysis for MBC under different operating conditions. • MBC has higher efficiency and specific net work output as compared to ABC

Nuclear reactor construction with bottom supported reactor vessel

International Nuclear Information System (INIS)

Sharbaugh, J.E.

1987-01-01

This patent describes an improved liquid metal nuclear reactor construction comprising: (a) a nuclear reactor core having a bottom platform support structure; (b) a reactor vessel for holding a large pool of low pressure liquid metal coolant and housing the core; (c) a containment structure surrounding the reactor vessel and having a sidewall spaced outwardly from the reactor vessel side wall and having a base mat spaced below the reactor vessel bottom end wall; (d) a central small diameter post anchored to the containment structure base mat and extending upwardly to the reactor vessel to axially fix the bottom end wall of the reactor vessel and provide a center column support for the lower end of the reactor core; (e) annular support structure disposed in the reactor vessel on the bottom end wall and extending about the lower end of the core; (f) structural support means disposed between the containment structure base mat and bottom end of the reactor vessel wall and cooperating for supporting the reactor vessel at its bottom end wall on the containment structure base mat to allow the reactor vessel to expand radially but substantially prevent any lateral motions that might be imposed by the occurrence of a seismic event; (g) a bed of insulating material disposed between the containment structure base mat and the bottom end wall of the reactor vessel and uniformly supporting the reactor vessel at its bottom end wall; freely expand radially from the central post as it heats up while providing continuous support thereof; (h) a deck supported upon the wall of the containment vessel above the top open end of the reactor vessel; and (i) extendible and retractable coupling means extending between the deck and the top open end of the reactor vessel and flexibly and sealably interconnecting the reactor vessel at its top end to the deck

Estimates of bottom roughness length and bottom shear stress in South San Francisco Bay, California

Science.gov (United States)

Cheng, R.T.; Ling, C.-H.; Gartner, J.W.; Wang, P.-F.

1999-01-01

A field investigation of the hydrodynamics and the resuspension and transport of participate matter in a bottom boundary layer was carried out in South San Francisco Bay (South Bay), California, during March-April 1995. Using broadband acoustic Doppler current profilers, detailed measurements of turbulent mean velocity distribution within 1.5 m above bed have been obtained. A global method of data analysis was used for estimating bottom roughness length zo and bottom shear stress (or friction velocities u*). Field data have been examined by dividing the time series of velocity profiles into 24-hour periods and independently analyzing the velocity profile time series by flooding and ebbing periods. The global method of solution gives consistent properties of bottom roughness length zo and bottom shear stress values (or friction velocities u*) in South Bay. Estimated mean values of zo and u* for flooding and ebbing cycles are different. The differences in mean zo and u* are shown to be caused by tidal current flood-ebb inequality, rather than the flooding or ebbing of tidal currents. The bed shear stress correlates well with a reference velocity; the slope of the correlation defines a drag coefficient. Forty-three days of field data in South Bay show two regimes of zo (and drag coefficient) as a function of a reference velocity. When the mean velocity is >25-30 cm s-1, the ln zo (and thus the drag coefficient) is inversely proportional to the reference velocity. The cause for the reduction of roughness length is hypothesized as sediment erosion due to intensifying tidal currents thereby reducing bed roughness. When the mean velocity is <25-30 cm s-1, the correlation between zo and the reference velocity is less clear. A plausible explanation of scattered values of zo under this condition may be sediment deposition. Measured sediment data were inadequate to support this hypothesis, but the proposed hypothesis warrants further field investigation.

Wet physical separation of MSWI bottom ash

NARCIS (Netherlands)

Muchova, L.

2010-01-01

Bottom ash (BA) from municipal solid waste incineration (MSWI) has high potential for the recovery of valuable secondary materials. For example, the MSWI bottom ash produced by the incinerator at Amsterdam contains materials such as non-ferrous metals (2.3%), ferrous metals (8-13%), gold (0.4 ppm),

The fabrication of a double-layer atom chip with through silicon vias for an ultra-high-vacuum cell

International Nuclear Information System (INIS)

Chuang, Ho-Chiao; Lin, Yun-Siang; Lin, Yu-Hsin; Huang, Chi-Sheng

2014-01-01

This study presents a double-layer atom chip that provides users with increased diversity in the design of the wire patterns and flexibility in the design of the magnetic field. It is more convenient for use in atomic physics experiments. A negative photoresist, SU-8, was used as the insulating layer between the upper and bottom copper wires. The electrical measurement results show that the upper and bottom wires with a width of 100 µm can sustain a 6 A current without burnout. Another focus of this study is the double-layer atom chips integrated with the through silicon via (TSV) technique, and anodically bonded to a Pyrex glass cell, which makes it a desired vacuum chamber for atomic physics experiments. Thus, the bonded glass cell not only significantly reduces the overall size of the ultra-high-vacuum (UHV) chamber but also conducts the high current from the backside to the front side of the atom chip via the TSV under UHV (9.5 × 10 −10  Torr). The TSVs with a diameter of 70 µm were etched through by the inductively coupled plasma ion etching and filled by the bottom-up copper electroplating method. During the anodic bonding process, the electroplated copper wires and TSVs on atom chips also need to pass the examination of the required bonding temperature of 250 °C, under an applied voltage of 1000 V. Finally, the UHV test of the double-layer atom chips with TSVs at room temperature can be reached at 9.5 × 10 −10  Torr, thus satisfying the requirements of atomic physics experiments under an UHV environment. (paper)

A novel sandwich differential capacitive accelerometer with symmetrical double-sided serpentine beam-mass structure

International Nuclear Information System (INIS)

Xiao, D B; Li, Q S; Hou, Z Q; Wang, X H; Chen, Z H; Xia, D W; Wu, X Z

2016-01-01

This paper presents a novel differential capacitive silicon micro-accelerometer with symmetrical double-sided serpentine beam-mass sensing structure and glass–silicon–glass sandwich structure. The symmetrical double-sided serpentine beam-mass sensing structure is fabricated with a novel pre-buried mask fabrication technology, which is convenient for manufacturing multi-layer sensors. The glass–silicon–glass sandwich structure is realized by a double anodic bonding process. To solve the problem of the difficulty of leading out signals from the top and bottom layer simultaneously in the sandwich sensors, a silicon pillar structure is designed that is inherently simple and low-cost. The prototype is fabricated and tested. It has low noise performance (the peak to peak value is 40 μg) and μg-level Allan deviation of bias (2.2 μg in 1 h), experimentally demonstrating the effectiveness of the design and the novel fabrication technology. (paper)

Bottoming organic Rankine cycle configurations to increase Internal Combustion Engines power output from cooling water waste heat recovery

International Nuclear Information System (INIS)

Peris, Bernardo; Navarro-Esbrí, Joaquín; Molés, Francisco

2013-01-01

This work is focused on waste heat recovery of jacket cooling water from Internal Combustion Engines (ICEs). Cooling water heat does not always find use due to its low temperature, typically around 90 °C, and usually is rejected to the ambient despite its high thermal power. An efficient way to take benefit from the ICE cooling water waste heat can be to increase the power output through suitable bottoming Organic Rankine Cycles (ORCs). Thereby, this work simulates six configurations using ten non flammable working fluids and evaluates their performances in efficiency, safety, cost and environmental terms. Results show that the Double Regenerative ORC using SES36 gets the maximum net efficiency of 7.15%, incrementing the ICE electrical efficiency up to 5.3%, although requires duplicating the number of main components and high turbine size. A more rigorous analysis, based on the system feasibility, shows that small improvements in the basic cycle provide similar gains compared to the most complex schemes proposed. So, the single Regenerative ORC using R236fa and the Reheat Regenerative ORC using R134a seem suitable cycles which provide a net efficiency of 6.55%, incrementing the ICE electrical efficiency up to 4.9%. -- Highlights: • Suitable bottoming cycles for ICE cooling water waste heat recovery are studied. • Non flammable working fluids and various ORC configurations are evaluated. • Double regenerative cycle using SES36 is the most efficient configuration. • Regenerative and reheat regenerative ORCs seem feasible cycles. • Electrical efficiency of the ICE can be improved up to 5.3%

Fall Bottom Trawl Survey

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The standardized NEFSC Fall Bottom Trawl Survey was initiated in 1963 and covered an area from Hudson Canyon, NY to Nova Scotia, Canada. Throughout the years,...

Winter Bottom Trawl Survey

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The standardized NEFSC Winter Bottom Trawl Survey was initiated in 1992 and covered offshore areas from the Mid-Atlantic to Georges Bank. Inshore strata were covered...

Summer Bottom Trawl Survey

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Sampling the coastal waters of the Gulf of Maine using the Northeast Fishery Science Center standardized bottom trawl has been problematic due to large areas of hard...

Spring Bottom Trawl Survey

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The standardized NEFSC Spring Bottom Trawl Survey was initiated in 1968 and covered an area from Cape Hatteras, NC, to Nova Scotia, Canada, at depths >27m....

Pretreatment and utilization of waste incineration bottom ashes

DEFF Research Database (Denmark)

Astrup, Thomas

2007-01-01

Within recent years, researchers and authorities have had increasing focus on leaching properties from waste incineration bottom ashes. Researchers have investigated processes such as those related to carbonation, weathering, metal complexation, and leaching control. Most of these investigations......, however, have had a strong emphasis on lab experiments with little focus on full scale bottom ash upgrading methods. The introduction of regulatory limit values restricting leaching from utilized bottom ashes, has created a need for a better understanding of how lab scale experiences can be utilized...

Bottom water circulation in Cascadia Basin

Science.gov (United States)

Hautala, Susan L.; Paul Johnson, H.; Hammond, Douglas E.

2009-10-01

A combination of beta spiral and minimum length inverse methods, along with a compilation of historical and recent high-resolution CTD data, are used to produce a quantitative estimate of the subthermocline circulation in Cascadia Basin. Flow in the North Pacific Deep Water, from 900-1900 m, is characterized by a basin-scale anticyclonic gyre. Below 2000 m, two water masses are present within the basin interior, distinguished by different potential temperature-salinity lines. These water masses, referred to as Cascadia Basin Bottom Water (CBBW) and Cascadia Basin Deep Water (CBDW), are separated by a transition zone at about 2400 m depth. Below the depth where it freely communicates with the broader North Pacific, Cascadia Basin is renewed by northward flow through deep gaps in the Blanco Fracture Zone that feeds the lower limb of a vertical circulation cell within the CBBW. Lower CBBW gradually warms and returns to the south at lighter density. Isopycnal layer renewal times, based on combined lateral and diapycnal advective fluxes, increase upwards from the bottom. The densest layer, existing in the southeast quadrant of the basin below ˜2850 m, has an advective flushing time of 0.6 years. The total volume flushing time for the entire CBBW is 2.4 years, corresponding to an average water parcel residence time of 4.7 years. Geothermal heating at the Cascadia Basin seafloor produces a characteristic bottom-intensified temperature anomaly and plays an important role in the conversion of cold bottom water to lighter density within the CBBW. Although covering only about 0.05% of the global seafloor, the combined effects of bottom heat flux and diapycnal mixing within Cascadia Basin provide about 2-3% of the total required global input to the upward branch of the global thermohaline circulation.

Development of cask body integrated with bottom plate

International Nuclear Information System (INIS)

Yoshida, Takuji; Sasaki, Tomoharu; Koyama, Yoichi; Kumagai, Yasuyuki; Watanabe, Yuichi; Takasa, Seiju

2017-01-01

The main parts of a metal cask for storage and transport of spent nuclear fuel consists of main body, neutron shield material and external cylinder. The forged main body has been manufactured as a cup shape by welding of 'forged body' and 'forged bottom plate' which are independently forged. JSW has developed the manufacturing technology of 'cask body integrated with bottom plate' which has no weld line with the goal of cost reduction, manufacturing period shortening and further reliability improvement. Manufacturing for the prototype of 'cask body integrated with bottom plate' has completed to verify mechanical properties and uniformity of the product which satisfy the specified values stipulated in JSME Code S FA1 2007 edition. Here, we report the manufacturing technology and obtained properties of 'cask body integrated with bottom plate'. (author)

Bottom production asymmetries at the LHC

Energy Technology Data Exchange (ETDEWEB)

Norrbin, E.; Vogt, R.

1999-01-01

We present results on bottom hadron production asymmetries at the LHC within both the Lund string fragmentation model and the intrinsic bottom model. The main aspects of the models are summarized and specific predictions for pp collisions at 14 TeV are given. Asymmetries are found to be very small at central rapidities increasing to a few percent at forward rapidities. At very large rapidities intrinsic production could dominate but this region is probably out of reach of any experiment.

Bottom production asymmetries at the LHC

International Nuclear Information System (INIS)

Norrbin, E.; Vogt, R.

1999-01-01

We present results on bottom hadron production asymmetries at the LHC within both the Lund string fragmentation model and the intrinsic bottom model. The main aspects of the models are summarized and specific predictions for pp collisions at 14 TeV are given. Asymmetries are found to be very small at central rapidities increasing to a few percent at forward rapidities. At very large rapidities intrinsic production could dominate but this region is probably out of reach of any experiment

To fractionate municipal solid waste incineration bottom ash: Key for utilisation?

Science.gov (United States)

Sormunen, Laura Annika; Rantsi, Riina

2015-11-01

For the past decade, the Finnish waste sector has increasingly moved from the landfilling of municipal solid waste towards waste incineration. New challenges are faced with the growing amounts of municipal solid waste incineration bottom ash, which are mainly landfilled at the moment. Since this is not a sustainable or a profitable solution, finding different utilisation applications for the municipal solid waste incineration bottom ash is crucial. This study reports a comprehensive analysis of bottom ash properties from one waste incineration plant in Finland, which was first treated with a Dutch bottom ash recovery technique called advanced dry recovery. This novel process separates non-ferrous and ferrous metals from bottom ash, generating mineral fractions of different grain sizes (0-2 mm, 2-5 mm, 5-12 mm and 12-50 mm). The main aim of the study was to assess, whether the advanced bottom ash treatment technique, producing mineral fractions of different grain sizes and therefore properties, facilitates the utilisation of municipal solid waste incineration bottom ash in Finland. The results were encouraging; the bottom ash mineral fractions have favourable behaviour against the frost action, which is especially useful in the Finnish conditions. In addition, the leaching of most hazardous substances did not restrict the utilisation of bottom ash, especially for the larger fractions (>5 mm). Overall, this study has shown that the advanced bottom ash recovering technique can be one solution to increase the utilisation of bottom ash and furthermore decrease its landfilling in Finland. © The Author(s) 2015.

Damage detection in hazardous waste storage tank bottoms using ultrasonic guided waves

Science.gov (United States)

Cobb, Adam C.; Fisher, Jay L.; Bartlett, Jonathan D.; Earnest, Douglas R.

2018-04-01

Detecting damage in storage tanks is performed commercially using a variety of techniques. The most commonly used inspection technologies are magnetic flux leakage (MFL), conventional ultrasonic testing (UT), and leak testing. MFL and UT typically involve manual or robotic scanning of a sensor along the metal surfaces to detect cracks or corrosion wall loss. For inspection of the tank bottom, however, the storage tank is commonly emptied to allow interior access for the inspection system. While there are costs associated with emptying a storage tank for inspection that can be justified in some scenarios, there are situations where emptying the tank is impractical. Robotic, submersible systems have been developed for inspecting these tanks, but there are some storage tanks whose contents are so hazardous that even the use of these systems is untenable. Thus, there is a need to develop an inspection strategy that does not require emptying the tank or insertion of the sensor system into the tank. This paper presents a guided wave system for inspecting the bottom of double-shelled storage tanks (DSTs), with the sensor located on the exterior side-wall of the vessel. The sensor used is an electromagnetic acoustic transducer (EMAT) that generates and receives shear-horizontal guided plate waves using magnetostriction principles. The system operates by scanning the sensor around the circumference of the storage tank and sending guided waves into the tank bottom at regular intervals. The data from multiple locations are combined using the synthetic aperture focusing technique (SAFT) to create a color-mapped image of the vessel thickness changes. The target application of the system described is inspection of DSTs located at the Hanford site, which are million-gallon vessels used to store nuclear waste. Other vessels whose exterior walls are accessible would also be candidates for inspection using the described approach. Experimental results are shown from tests on multiple

Industrial mixing techniques for Hanford double-shell tanks

International Nuclear Information System (INIS)

Daymo, E.A.

1997-09-01

Jet mixer pumps are currently the baseline technology for sludge mobilization and mixing in one-million gallon double-shell tanks at the Hanford and Savannah River Sites. Improvements to the baseline jet mixer pump technology are sought because jet mixer pumps have moving parts that may fail or require maintenance. Moreover, jet mixers are relatively expensive, they heat the waste, and, in some cases, may not mobilize enough of the sludge. This report documents a thorough literature search for commercially available applicable mixing technologies that could be used for double-shell tank sludge mobilization and mixing. Textbooks, research articles, conference proceedings, mixing experts, and the Thomas Register were consulted to identify applicable technologies. While there are many commercial methods that could be used to mobilize sludge or mix the contents of a one-million gallon tank, few will work given the geometrical constraints (e.g., the mixer must fit through a 1.07-m-diameter riser) or the tank waste properties (e.g., the sludge has such a high yield stress that it generally does not flow under its own weight). Pulsed fluid jets and submersible Flygt mixers have already been identified at Hanford and Savannah River Sites for double-shell tank mixing applications. While these mixing technologies may not be applicable for double-shell tanks that have a thick sludge layer at the bottom (since too many of these mixers would need to be installed to mobilize most of the sludge), they may have applications in tanks that do not have a settled solids layer. Retrieval projects at Hanford and other U.S. Department of Energy sites are currently evaluating the effectiveness of these mixing techniques for tank waste applications. The literature search did not reveal any previously unknown technologies that should be considered for sludge mobilization and mixing in one-million gallon double-shell tanks

Strong Flows of Bottom Water in Abyssal Channels of the Atlantic

Science.gov (United States)

Morozov, E. G.

Analysis of bottom water transport through the abyssal channels of the Atlantic Ocean is presented. The study is based on recent observations in the Russian expeditions and historical data. A strong flow of Antarctic Bottom Water from the Argentine Basin to the Brazil Basin through the Vema Channel is observed on the basis of lowered profilers and anchored buoys with current meters. The further flow of bottom water in the Brazil Basin splits in the northern part of the basin. Part of the bottom water flows to the East Atlantic through the Romanche and Chain fracture zones. The other part follows the bottom topography and flows to the northwester into the North American Basin. Part of the northwesterly flow propagates through the Vema Fracture Zone into the Northeastern Atlantic. This flow generally fills the bottom layer in the Northeastern Atlantic basins. The flows of bottom waters through the Romanche and Chain fracture zones do not spread to the Northeast Atlantic due to strong mixing in the equatorial zone and enhanced transformation of bottom water properties.

Bottom friction optimization for a better barotropic tide modelling

Science.gov (United States)

Boutet, Martial; Lathuilière, Cyril; Son Hoang, Hong; Baraille, Rémy

2015-04-01

At a regional scale, barotropic tides are the dominant source of variability of currents and water heights. A precise representation of these processes is essential because of their great impacts on human activities (submersion risks, marine renewable energies, ...). Identified sources of error for tide modelling at a regional scale are the followings: bathymetry, boundary forcing and dissipation due to bottom friction. Nevertheless, bathymetric databases are nowadays known with a good accuracy, especially over shelves, and global tide models performances are better than ever. The most promising improvement is thus the bottom friction representation. The method used to estimate bottom friction is the simultaneous perturbation stochastic approximation (SPSA) which consists in the approximation of the gradient based on a fixed number of cost function measurements, regardless of the dimension of the vector to be estimated. Indeed, each cost function measurement is obtained by randomly perturbing every component of the parameter vector. An important feature of SPSA is its relative ease of implementation. In particular, the method does not require the development of tangent linear and adjoint version of the circulation model. Experiments are carried out to estimate bottom friction with the HYbrid Coordinate Ocean Model (HYCOM) in barotropic mode (one isopycnal layer). The study area is the Northeastern Atlantic margin which is characterized by strong currents and an intense dissipation. Bottom friction is parameterized with a quadratic term and friction coefficient is computed with the water height and the bottom roughness. The latter parameter is the one to be estimated. Assimilated data are the available tide gauge observations. First, the bottom roughness is estimated taking into account bottom sediment natures and bathymetric ranges. Then, it is estimated with geographical degrees of freedom. Finally, the impact of the estimation of a mixed quadratic/linear friction

Description of double-shell tank selection criteria for inspection

International Nuclear Information System (INIS)

Schwenk, E.B.; Scott, K.V.

1996-01-01

Technical criteria for selecting double-shelf tanks's (DST's) for inspection are presented. Inspection of DST's is planned to non-destructively determine the general condition of their inner wall and bottom knuckle. Inspection of representative tanks will provide a basis for evaluating the integrity of all the DST's and provide a basis for estimating remaining life. The selection criteria recommended are tank age based on date-of-first fluid entry, waste temperature, corrosion inhibitor levels, deviations from normal behavior - involving sludge levels, hydrogen release and waste transfers - least waste depth fluctuation, tank steel type, other chemical species that could activate stress-corrosion cracking, and waste types

Bottom Trawl Survey Protocol Development (HB0706, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Cruise objectives include: 1) Investigate performance characteristics of new research bottom trawl; 2) Develop standard operating procedures for the NEFSC Bottom...

A Water Model Study on Mixing Behavior of the Two-Layered Bath in Bottom Blown Copper Smelting Furnace

Science.gov (United States)

Shui, Lang; Cui, Zhixiang; Ma, Xiaodong; Jiang, Xu; Chen, Mao; Xiang, Yong; Zhao, Baojun

2018-05-01

The bottom-blown copper smelting furnace is a novel copper smelter developed in recent years. Many advantages of this furnace have been found, related to bath mixing behavior under its specific gas injection scheme. This study aims to use an oil-water double-phased laboratory-scale model to investigate the impact of industry-adjustable variables on bath mixing time, including lower layer thickness, gas flow rate, upper layer thickness and upper layer viscosity. Based on experimental results, an overall empirical relationship of mixing time in terms of these variables has been correlated, which provides the methodology for industry to optimize mass transfer in the furnace.

Bottom and top physics

International Nuclear Information System (INIS)

Foley, K.J.; Fridman, A.; Gilman, F.J.; Herten, G.; Hinchliffe, I.; Jawahery, A.; Sanda, A.; Schmidt, M.P.; Schubert, K.R.

1987-09-01

The production of bottom quarks at the SSC and the formalism and phenomenology of observing CP violation in B meson decays is discussed. The production of a heavy t quark which decays into a real W boson, and what we might learn from its decays is examined

Small Engines as Bottoming Cycle Steam Expanders for Internal Combustion Engines

OpenAIRE

Weerasinghe, Rohitha; Hounsham, Sandra

2017-01-01

Heat recovery bottoming cycles for internal combustion engines have opened new avenues for research into small steam expanders [1]. Dependable data for small steam expanders will allow us to predict on their suitability as bottoming cycle engines and the fuel economy achieved by using them as bottoming cycles. Wankel Engines, with its lower resistance properties at small scale provide excellent contenders for bottoming cycle expanders. Present paper is based on results of experiments carried ...

Peabody Western Coal cuts costs with bottom-dump haulers

Energy Technology Data Exchange (ETDEWEB)

Perla, S.; Baecker, G.; Morgan, W. [Empire Machinery, Mesa, AZ (United States)

1995-04-01

A new hauling concept has been introduced at the Black Mesa and Kayenta coal mines of the Peabody Western Coal Co. in northern Arizona, USA. The article describes the switch from Caterpillar 992 wheel loaders with 136 t bottom-dump trucks to 272 t bottom-dump trucks. Cat 789 off-highway trucks were modified to pull bottom-dump trucks. Haulage costs per ton of coal and cost per ton-mile have fallen significantly since the introduction of the new large hauling method. 7 figs., 2 photos.

Spreading of Antarctic Bottom Water in the Atlantic Ocean

OpenAIRE

Morozov, E.; Tarakanov, R. Y.; Zenk, Walter

2012-01-01

This paper describes the transport of bottom water from its source region in the Weddell Sea through the abyssal channels of the Atlantic Ocean. The research brings together the recent observations and historical data. A strong flow of Antarctic Bottom Water through the Vema Channel is analyzed. The mean speed of the flow is 30 cm/s. A temperature increase was found in the deep Vema Channel, which has been observed for 30 years already. The flow of bottom water in the northern part of the Bra...

Search for scalar bottom quarks from gluino decays in collisions at.

Science.gov (United States)

Abulencia, A; Acosta, D; Adelman, J; Affolder, T; Akimoto, T; Albrow, M G; Ambrose, D; Amerio, S; Amidei, D; Anastassov, A; Anikeev, K; Annovi, A; Antos, J; Aoki, M; Apollinari, G; Arguin, J-F; Arisawa, T; Artikov, A; Ashmanskas, W; Attal, A; Azfar, F; Azzi-Bacchetta, P; Azzurri, P; Bacchetta, N; Bachacou, H; Badgett, W; Barbaro-Galtieri, A; Barnes, V E; Barnett, B A; Baroiant, S; Bartsch, V; Bauer, G; Bedeschi, F; Behari, S; Belforte, S; Bellettini, G; Bellinger, J; Belloni, A; Ben-Haim, E; Benjamin, D; Beretvas, A; Beringer, J; Berry, T; Bhatti, A; Binkley, M; Bisello, D; Bishai, M; Blair, R E; Blocker, C; Bloom, K; Blumenfeld, B; Bocci, A; Bodek, A; Boisvert, V; Bolla, G; Bolshov, A; Bortoletto, D; Boudreau, J; Bourov, S; Boveia, A; Brau, B; Bromberg, C; Brubaker, E; Budagov, J; Budd, H S; Budd, S; Burkett, K; Busetto, G; Bussey, P; Byrum, K L; Cabrera, S; Campanelli, M; Campbell, M; Canelli, F; Canepa, A; Carlsmith, D; Carosi, R; Carron, S; Casarsa, M; Castro, A; Catastini, P; Cauz, D; Cavalli-Sforza, M; Cerri, A; Cerrito, L; Chang, S H; Chapman, J; Chen, Y C; Chertok, M; Chiarelli, G; Chlachidze, G; Chlebana, F; Cho, I; Cho, K; Chokheli, D; Chou, J P; Chu, P H; Chuang, S H; Chung, K; Chung, W H; Chung, Y S; Ciljak, M; Ciobanu, C I; Ciocci, M A; Clark, A; Clark, D; Coca, M; Connolly, A; Convery, M E; Conway, J; Cooper, B; Copic, K; Cordelli, M; Cortiana, G; Cruz, A; Cuevas, J; Culbertson, R; Cyr, D; DaRonco, S; D'Auria, S; D'onofrio, M; Dagenhart, D; de Barbaro, P; De Cecco, S; Deisher, A; De Lentdecker, G; Dell'Orso, M; Demers, S; Demortier, L; Deng, J; Deninno, M; De Pedis, D; Derwent, P F; Dionisi, C; Dittmann, J R; Dituro, P; Dörr, C; Dominguez, A; Donati, S; Donega, M; Dong, P; Donini, J; Dorigo, T; Dube, S; Ebina, K; Efron, J; Ehlers, J; Erbacher, R; Errede, D; Errede, S; Eusebi, R; Fang, H C; Farrington, S; Fedorko, I; Fedorko, W T; Feild, R G; Feindt, M; Fernandez, J P; Field, R; Flanagan, G; Flores-Castillo, L R; Foland, A; Forrester, S; Foster, G W; Franklin, M; Freeman, J C; Fujii, Y; Furic, I; Gajjar, A; Gallinaro, M; Galyardt, J; Garcia, J E; Garcia Sciverez, M; Garfinkel, A F; Gay, C; Gerberich, H; Gerchtein, E; Gerdes, D; Giagu, S; di Giovanni, G P; Giannetti, P; Gibson, A; Gibson, K; Ginsburg, C; Giokaris, N; Giolo, K; Giordani, M; Giunta, M; Giurgiu, G; Glagolev, V; Glenzinski, D; Gold, M; Goldschmidt, N; Goldstein, J; Gomez, G; Gomez-Ceballos, G; Goncharov, M; González, O; Gorelov, I; Goshaw, A T; Gotra, Y; Goulianos, K; Gresele, A; Griffiths, M; Grinstein, S; Grosso-Pilcher, C; Grundler, U; Guimaraes da Costa, J; Haber, C; Hahn, S R; Hahn, K; Halkiadakis, E; Hamilton, A; Han, B-Y; Handler, R; Happacher, F; Hara, K; Hare, M; Harper, S; Harr, R F; Harris, R M; Hatakeyama, K; Hauser, J; Hays, C; Hayward, H; Heijboer, A; Heinemann, B; Heinrich, J; Hennecke, M; Herndon, M; Heuser, J; Hidas, D; Hill, C S; Hirschbuehl, D; Hocker, A; Holloway, A; Hou, S; Houlden, M; Hsu, S-C; Huffman, B T; Hughes, R E; Huston, J; Ikado, K; Incandela, J; Introzzi, G; Iori, M; Ishizawa, Y; Ivanov, A; Iyutin, B; James, E; Jang, D; Jayatilaka, B; Jeans, D; Jensen, H; Jeon, E J; Jones, M; Joo, K K; Jun, S Y; Junk, T R; Kamon, T; Kang, J; Karagoz-Unel, M; Karchin, P E; Kato, Y; Kemp, Y; Kephart, R; Kerzel, U; Khotilovich, V; Kilminster, B; Kim, D H; Kim, H S; Kim, J E; Kim, M J; Kim, M S; Kim, S B; Kim, S H; Kim, Y K; Kirby, M; Kirsch, L; Klimenko, S; Klute, M; Knuteson, B; Ko, B R; Kobayashi, H; Kondo, K; Kong, D J; Konigsberg, J; Kordas, K; Korytov, A; Kotwal, A V; Kovalev, A; Kraus, J; Kravchenko, I; Kreps, M; Kreymer, A; Kroll, J; Krumnack, N; Kruse, M; Krutelyov, V; Kuhlmann, S E; Kusakabe, Y; Kwang, S; Laasanen, A T; Lai, S; Lami, S; Lammel, S; Lancaster, M; Lander, R L; Lannon, K; Lath, A; Latino, G; Lazzizzera, I; Lecci, C; Lecompte, T; Lee, J; Lee, J; Lee, S W; Lefèvre, R; Leonardo, N; Leone, S; Levy, S; Lewis, J D; Li, K; Lin, C; Lin, C S; Lindgren, M; Lipeles, E; Liss, T M; Lister, A; Litvintsev, D O; Liu, T; Liu, Y; Lockyer, N S; Loginov, A; Loreti, M; Loverre, P; Lu, R-S; Lucchesi, D; Lujan, P; Lukens, P; Lungu, G; Lyons, L; Lys, J; Lysak, R; Lytken, E; Mack, P; MacQueen, D; Madrak, R; Maeshima, K; Maksimovic, P; Manca, G; Margaroli, F; Marginean, R; Marino, C; Martin, A; Martin, M; Martin, V; Martínez, M; Maruyama, T; Matsunaga, H; Mattson, M E; Mazini, R; Mazzanti, P; McFarland, K S; McGivern, D; McIntyre, P; McNamara, P; McNulty, R; Mehta, A; Menzemer, S; Menzione, A; Merkel, P; Mesropian, C; Messina, A; von der Mey, M; Miao, T; Miladinovic, N; Miles, J; Miller, R; Miller, J S; Mills, C; Milnik, M; Miquel, R; Miscetti, S; Mitselmakher, G; Miyamoto, A; Moggi, N; Mohr, B; Moore, R; Morello, M; Movilla Fernandez, P; Mülmenstädt, J; Mukherjee, A; Mulhearn, M; Muller, Th; Mumford, R; Munar, A; Murat, P; Nachtman, J; Nahn, S; Nakano, I; Napier, A; Naumov, D; Necula, V; Neu, C; Neubauer, M S; Nielsen, J; Nigmanov, T; Nodulman, L; Norniella, O; Ogawa, T; Oh, S H; Oh, Y D; Okusawa, T; Oldeman, R; Orava, R; Osterberg, K; Pagliarone, C; Palencia, E; Paoletti, R; Papadimitriou, V; Papikonomou, A; Paramonov, A A; Parks, B; Pashapour, S; Patrick, J; Pauletta, G; Paulini, M; Paus, C; Pellett, D E; Penzo, A; Phillips, T J; Piacentino, G; Piedra, J; Pitts, K; Plager, C; Pondrom, L; Pope, G; Portell, X; Poukhov, O; Pounder, N; Prakoshyn, F; Pronko, A; Proudfoot, J; Ptohos, F; Punzi, G; Pursley, J; Rademacker, J; Rahaman, A; Rakitin, A; Rappoccio, S; Ratnikov, F; Reisert, B; Rekovic, V; van Remortel, N; Renton, P; Rescigno, M; Richter, S; Rimondi, F; Rinnert, K; Ristori, L; Robertson, W J; Robson, A; Rodrigo, T; Rogers, E; Rolli, S; Roser, R; Rossi, M; Rossin, R; Rott, C; Ruiz, A; Russ, J; Rusu, V; Ryan, D; Saarikko, H; Sabik, S; Safonov, A; Sakumoto, W K; Salamanna, G; Salto, O; Saltzberg, D; Sanchez, C; Santi, L; Sarkar, S; Sato, K; Savard, P; Savoy-Navarro, A; Scheidle, T; Schlabach, P; Schmidt, E E; Schmidt, M P; Schmitt, M; Schwarz, T; Scodellaro, L; Scott, A L; Scribano, A; Scuri, F; Sedov, A; Seidel, S; Seiya, Y; Semenov, A; Semeria, F; Sexton-Kennedy, L; Sfiligoi, I; Shapiro, M D; Shears, T; Shepard, P F; Sherman, D; Shimojima, M; Shochet, M; Shon, Y; Shreyber, I; Sidoti, A; Siegrist, J L; Sill, A; Sinervo, P; Sisakyan, A; Sjolin, J; Skiba, A; Slaughter, A J; Sliwa, K; Smirnov, D; Smith, J R; Snider, F D; Snihur, R; Soderberg, M; Soha, A; Somalwar, S; Sorin, V; Spalding, J; Spinella, F; Squillacioti, P; Stanitzki, M; Staveris-Polykalas, A; St Dennis, R; Stelzer, B; Stelzer-Chilton, O; Stentz, D; Strologas, J; Stuart, D; Suh, J S; Sukhanov, A; Sumorok, K; Sun, H; Suzuki, T; Taffard, A; Tafirout, R; Takashima, R; Takeuchi, Y; Takikawa, K; Tanaka, M; Tanaka, R; Tecchio, M; Teng, P K; Terashi, K; Tether, S; Thom, J; Thompson, A S; Thomson, E; Tipton, P; Tiwari, V; Tkaczyk, S; Toback, D; Tokar, S; Tollefson, K; Tomura, T; Tonelli, D; Tönnesmann, M; Torre, S; Torretta, D; Tourneur, S; Trischuk, W; Tsuchiya, R; Tsuno, S; Turini, N; Ukegawa, F; Unverhau, T; Uozumi, S; Usynin, D; Vacavant, L; Vaiciulis, A; Vallecorsa, S; Varganov, A; Vataga, E; Velev, G; Veramendi, G; Veszpremi, V; Vickey, T; Vidal, R; Vila, I; Vilar, R; Vollrath, I; Volobouev, I; Würthwein, F; Wagner, P; Wagner, R G; Wagner, R L; Wagner, W; Wallny, R; Walter, T; Wan, Z; Wang, M J; Wang, S M; Warburton, A; Ward, B; Waschke, S; Waters, D; Watts, T; Weber, M; Wester, W C; Whitehouse, B; Whiteson, D; Wicklund, A B; Wicklund, E; Williams, H H; Wilson, P; Winer, B L; Wittich, P; Wolbers, S; Wolfe, C; Worm, S; Wright, T; Wu, X; Wynne, S M; Yagil, A; Yamamoto, K; Yamaoka, J; Yamashita, Y; Yang, C; Yang, U K; Yao, W M; Yeh, G P; Yoh, J; Yorita, K; Yoshida, T; Yu, I; Yu, S S; Yun, J C; Zanello, L; Zanetti, A; Zaw, I; Zetti, F; Zhang, X; Zhou, J; Zucchelli, S

2006-05-05

We searched for scalar bottom quarks 156 pb(-1) of pp collisions at radicalS = 1.96 recorded by the Collider Detector at Fermilab II experiment at the Tevatron. Scalar bottom quarks can be produced from gluino decays in -parity conserving models of supersymmetry when the mass of the gluino exceeds that of the scalar bottom quark. Then, a scalar bottom quark can decay into a bottom quark and a neutralino. To search for this scenario, we investigated events with large missing transverse energy and at least three jets, two or more of which were identified as containing a secondary vertex from the hadronization of quarks. We found four candidate events, where 2.6 +/- 0.7 are expected from standard model processes, and placed 95% confidence level lower limits on gluino and scalar bottom quark masses of up to 280 and 240 GeV/c(2), respectively.

Magnetic Anticrossing of 1D Subbands in Coupled Ballistic Double Quantum Wires

International Nuclear Information System (INIS)

Blount, Mark A.; Moon, Jeong-Sun; Simmons, Jerry A.; Lyo, Sungkwun K.; Wendt, Joel R.; Reno, John L.

2000-01-01

We study the low-temperature in-plane magnetoconductance of vertically coupled double quantum wires. Using a novel flip-chip technique, the wires are defined by two pairs of mutually aligned split gates on opposite sides of a s 1 micron thick AlGaAs/GaAs double quantum well heterostructure. We observe quantized conductance steps due to each quantum well and demonstrate independent control of each ID wire. A broad dip in the magnetoconductance at -6 T is observed when a magnetic field is applied perpendicular to both the current and growth directions. This conductance dip is observed only when 1D subbands are populated in both the top and bottom constrictions. This data is consistent with a counting model whereby the number of subbands crossing the Fermi level changes with field due to the formation of an anticrossing in each pair of 1D subbands

Bottom friction. A practical approach to modelling coastal oceanography

Science.gov (United States)

Bolanos, Rodolfo; Jensen, Palle; Kofoed-Hansen, Henrik; Tornsfeldt Sørensen, Jacob

2017-04-01

Coastal processes imply the interaction of the atmosphere, the sea, the coastline and the bottom. The spatial gradients in this area are normally large, induced by orographic and bathymetric features. Although nowadays it is possible to obtain high-resolution bathymetry, the details of the seabed, e.g. sediment type, presence of biological material and living organisms are not available. Additionally, these properties as well as bathymetry can also be highly dynamic. These bottom characteristics are very important to describe the boundary layer of currents and waves and control to a large degree the dissipation of flows. The bottom friction is thus typically a calibration parameter in numerical modelling of coastal processes. In this work, we assess this process and put it into context of other physical processes uncertainties influencing wind-waves and currents in the coastal areas. A case study in the North Sea is used, particularly the west coast of Denmark, where water depth of less than 30 m cover a wide fringe along the coast, where several offshore wind farm developments are being carried out. We use the hydrodynamic model MIKE 21 HD and the spectral wave model MIKE 21 SW to simulate atmosphere and tidal induced flows and the wind wave generation and propagation. Both models represent state of the art and have been developed for flexible meshes, ideal for coastal oceanography as they can better represent coastlines and allow a variable spatial resolution within the domain. Sensitivity tests to bottom friction formulations are carried out into context of other processes (e.g. model forcing uncertainties, wind and wave interactions, wind drag coefficient). Additionally, a map of varying bottom properties is generated based on a literature survey to explore the impact of the spatial variability. Assessment of different approaches is made in order to establish a best practice regarding bottom friction and coastal oceanographic modelling. Its contribution is also

SPREADING OF ANTARCTIC BOTTOM WATER IN THE ATLANTIC OCEAN

Directory of Open Access Journals (Sweden)

Eugene Morozov

2012-01-01

Full Text Available This paper describes the transport of bottom water from its source region in the Weddell Sea through the abyssal channels of the Atlantic Ocean. The research brings together the recent observations and historical data. A strong flow of Antarctic Bottom Water through the Vema Channel is analyzed. The mean speed of the flow is 30 cm/s. A temperature increase was found in the deep Vema Channel, which has been observed for 30 years already. The flow of bottom water in the northern part of the Brazil Basin splits. Part of the water flows through the Romanche and Chain fracture zones. The other part flows to the North American Basin. Part of the latter flow propagates through the Vema Fracture Zone into the Northeast Atlantic. The properties of bottom water in the Kane Gap and Discovery Gap are also analyzed.

Bottom-water observations in the Vema fracture zone

Science.gov (United States)

Eittreim, Stephen L.; Biscaye, Pierre E.; Jacobs, Stanley S.

1983-03-01

The Vema fracture zone trough, at 11°N between 41° and 45°E, is open to the west at the 5000-m level but is silled at the 4650-m level on the east where it intersects the axis of the Mid-Atlantic Ridge. The trough is filled with Antarctic Bottom Water (AABW) with a potential temperature of 1.32°C and salinity of 34.82 ppt. The bottom water is thermally well mixed in a nearly homogeneous layer about 700 m thick. The great thickness of this bottom layer, as compared with the bottom-water structure of the western Atlantic basin, may result from enhanced mixing induced by topographic constriction at the west end of the fracture zone trough. A benthic thermocline, with potential temperature gradients of about 1.2 mdeg m-1, is associated with an abrupt increase in turbidity with depth at about 1200 m above bottom. A transitional layer of more moderate temperature gradients, about 0.4 mdeg m-1, lies between the benthic thermocline above and the AABW below. The AABW layer whose depth-averaged suspended paniculate concentrations range from 8 to 19 μg L-1, is consistently higher in turbidity than the overlying waters. At the eastern end of the trough, 140 m below sill depth, very low northeastward current velocities, with maximums of 3 cm s-1, were recorded for an 11-day period.

Bottom head failure program plan

International Nuclear Information System (INIS)

Meyer, R.O.

1989-01-01

Earlier this year the NRC staff presented a Revised Severe Accident Research Program Plan (SECY-89-123) to the Commission and initiated work on that plan. Two of the near-term issues in that plan involve failure of the bottom head of the reactor pressure vessel. These two issues are (1) depressurization and DCH and (2) BWR Mark I Containment Shell Meltthrough. ORNL has developed models for several competing failure mechanisms for BWRs. INEL has performed analytical and experimental work directly related to bottom head failure in connection with several programs. SNL has conducted a number of analyses and experimental activities to examine the failure of LWR vessels. In addition to the government-sponsored work mentioned above, EPRI and FAI performed studies on vessel failure for the Industry Degraded Core Rulemaking Program (IDCOR). EPRI examined the failure of a PWR vessel bottom head without penetrations, as found in some Combustion Engineering reactors. To give more attention to this subject as called for by the revised Severe Accident Research Plan, two things are being done. First, work previously done is being reviewed carefully to develop an overall picture and to determine the reliability of assumptions used in those studies. Second, new work is being planned for FY90 to try to complete a reasonable understanding of the failure process. The review and planning are being done in close cooperation with the ACRS. Results of this exercise will be presented in this paper

Aluminium alloys in municipal solid waste incineration bottom ash.

Science.gov (United States)

Hu, Yanjun; Rem, Peter

2009-05-01

With the increasing growth of incineration of household waste, more and more aluminium is retained in municipal solid waste incinerator bottom ash. Therefore recycling of aluminium from bottom ash becomes increasingly important. Previous research suggests that aluminium from different sources is found in different size fractions resulting in different recycling rates. The purpose of this study was to develop analytical and sampling techniques to measure the particle size distribution of individual alloys in bottom ash. In particular, cast aluminium alloys were investigated. Based on the particle size distribution it was computed how well these alloys were recovered in a typical state-of-the-art treatment plant. Assessment of the cast alloy distribution was carried out by wet physical separation processes, as well as chemical methods, X-ray fluorescence analysis and electron microprobe analysis. The results from laboratory analyses showed that cast alloys tend to concentrate in the coarser fractions and therefore are better recovered in bottom ash treatment plants.

Bottom-up modeling of oil production: A review of approaches

International Nuclear Information System (INIS)

Jakobsson, Kristofer; Söderbergh, Bengt; Snowden, Simon; Aleklett, Kjell

2014-01-01

Bottom-up models of oil production are continuously being used to guide investments and policymaking. Compared to simpler top-down models, bottom-up models have a number of advantages due to their modularity, flexibility and concreteness. The purposes of this paper is to identify the crucial modeling challenges, compare the different ways in which nine existing models handle them, assess the appropriateness of these models, and point to possibilities of further development. The conclusions are that the high level of detail in bottom-up models is of questionable value for predictive accuracy, but of great value for identifying areas of uncertainty and new research questions. There is a potential for improved qualitative insights through systematic sensitivity analysis. This potential is at present largely unrealized. - Highlights: • Bottom-up models are influential in the study of the oil production supply chain. • Nine existing bottom-up models are reviewed. • The high level of detail is of questionable value for predictive accuracy. • There is a potential for more systematic sensitivity analysis

Adsorption of organic pollutants from coking and papermaking wastewaters by bottom ash.

Science.gov (United States)

Sun, Wei-ling; Qu, Yan-zhi; Yu, Qing; Ni, Jin-ren

2008-06-15

Bottom ash, a power plant waste, was used to remove the organic pollutants in coking wastewater and papermaking wastewater. Particular attention was paid on the effect of bottom ash particle size and dosage on the removal of chemical oxygen demand (COD). UV-vis spectra, fluorescence excitation-emission matrix (FEEM) spectra, Fourier transform infrared (FTIR) spectra, and scanning electron microscopic (SEM) photographs were investigated to characterize the wastewaters and bottom ash. The results show that the COD removal efficiencies increase with decreasing particle sizes of bottom ash, and the COD removal efficiency for coking wastewater is much higher than that for papermaking wastewater due to its high percentage of particle organic carbon (POC). Different trends of COD removal efficiency with bottom ash dosage are also observed for coking and papermaking wastewaters because of their various POC concentrations. Significant variations are observed in the FEEM spectra of wastewaters after treatment by bottom ash. New excitation-emission peaks are found in FEEM spectra, and the fluorescence intensities of the peaks decrease. A new transmittance band in the region of 1400-1420 cm(-1) is observed in FTIR spectra of bottom ash after adsorption. The SEM photographs reveal that the surface of bottom ash particles varies evidently after adsorption.

Adsorption of organic pollutants from coking and papermaking wastewaters by bottom ash

International Nuclear Information System (INIS)

Sun Weiling; Qu Yanzhi; Yu Qing; Ni Jinren

2008-01-01

Bottom ash, a power plant waste, was used to remove the organic pollutants in coking wastewater and papermaking wastewater. Particular attention was paid on the effect of bottom ash particle size and dosage on the removal of chemical oxygen demand (COD). UV-vis spectra, fluorescence excitation-emission matrix (FEEM) spectra, Fourier transform infrared (FTIR) spectra, and scanning electron microscopic (SEM) photographs were investigated to characterize the wastewaters and bottom ash. The results show that the COD removal efficiencies increase with decreasing particle sizes of bottom ash, and the COD removal efficiency for coking wastewater is much higher than that for papermaking wastewater due to its high percentage of particle organic carbon (POC). Different trends of COD removal efficiency with bottom ash dosage are also observed for coking and papermaking wastewaters because of their various POC concentrations. Significant variations are observed in the FEEM spectra of wastewaters after treatment by bottom ash. New excitation-emission peaks are found in FEEM spectra, and the fluorescence intensities of the peaks decrease. A new transmittance band in the region of 1400-1420 cm -1 is observed in FTIR spectra of bottom ash after adsorption. The SEM photographs reveal that the surface of bottom ash particles varies evidently after adsorption

Three-Dimensional Adjustment of Stratified Flow Over a Sloping Bottom

National Research Council Canada - National Science Library

Chapman, David

2002-01-01

This study focused on understanding how advection of density within the bottom boundary layer influence the three-dimensional structure, evolution, and dynamics of both the bottom boundary layer and the overlying (interior) flow...

Polymethylmethacrylate-based luminescent solar concentrators with bottom-mounted solar cells

International Nuclear Information System (INIS)

Zhang, Yi; Sun, Song; Kang, Rui; Zhang, Jun; Zhang, Ningning; Yan, Wenhao; Xie, Wei; Ding, Jianjun; Bao, Jun; Gao, Chen

2015-01-01

Graphical abstract: - Highlights: • Bottom-mounted luminescent solar concentrators on dye-doped plates were studied. • The mechanism of transport process was proposed. • The fabricated luminescent solar concentrator achieved a gain of 1.38. • Power conversion efficiency of 5.03% was obtained with cell area coverage of 27%. • The lowest cost per watt of $1.89 was optimized with cell area coverage of 18%. - Abstract: Luminescent solar concentrators offer an attractive approach to concentrate sunlight economically without tracking, but the narrow absorption band of luminescent materials hinders their further development. This paper describes bottom-mounted luminescent solar concentrators on dye-doped polymethylmethacrylate plates that absorb not only the waveguided light but also the transmitted sunlight and partial fluorescent light in the escape cone. A series of bottom-mounted luminescent solar concentrators with size of 78 mm × 78 mm × 7 mm were fabricated and their gain and power conversion efficiency were investigated. The transport process of the waveguided light and the relationship between the bottom-mounted cells were studied to optimize the performance of the device. The bottom-mounted luminescent solar concentrator with cell area coverage of 9% displayed a cell gain of 1.38, to our best knowledge, which is the highest value for dye-doped polymethylmethacrylate plate luminescent solar concentrators. Power conversion efficiency as high as 5.03% was obtained with cell area coverage of 27%. Furthermore, the bottom-mounted luminescent solar concentrator was found to have a lowest cost per watt of $1.89 with cell area coverage of 18%. These results suggested that the fabricated bottom-mounted luminescent solar concentrator may have a potential in low-cost building integrated photovoltaic application

Reuse potential of low-calcium bottom ash as aggregate through pelletization.

Science.gov (United States)

Geetha, S; Ramamurthy, K

2010-01-01

Coal combustion residues which include fly ash, bottom ash and boiler slag is one of the major pollutants as these residues require large land area for their disposal. Among these residues, utilization of bottom ash in the construction industry is very low. This paper explains the use of bottom ash through pelletization. Raw bottom ash could not be pelletized as such due to its coarseness. Though pulverized bottom ash could be pelletized, the pelletization efficiency was low, and the aggregates were too weak to withstand the handling stresses. To improve the pelletization efficiency, different clay and cementitious binders were used with bottom ash. The influence of different factors and their interaction effects were studied on the duration of pelletization process and the pelletization efficiency through fractional factorial design. Addition of binders facilitated conversion of low-calcium bottom ash into aggregates. To achieve maximum pelletization efficiency, the binder content and moisture requirements vary with type of binder. Addition of Ca(OH)(2) improved the (i) pelletization efficiency, (ii) reduced the duration of pelletization process from an average of 14-7 min, and (iii) reduced the binder dosage for a given pelletization efficiency. For aggregate with clay binders and cementitious binder, Ca(OH)(2) and binder dosage have significant effect in reducing the duration of pelletization process. 2010 Elsevier Ltd. All rights reserved.

Refinement of the bottom boundary of the INES scale

International Nuclear Information System (INIS)

Ferjencik, Milos

2010-01-01

No existing edition of the International Nuclear Events Scale (INES) Manual addresses in depth the determination of the bottom boundary of the Scale, although a need for a definition is felt. The article introduces a method for determining the INES bottom boundary applicable to pressurized water reactors. This bottom boundary is put identical with the threshold of degradation of the installation's nuclear safety assurance. A comprehensive flowchart has been developed as the main outcome of the analysis of the nuclear safety assurance violation issue. The use of this flowchart in INES classification to replace the introductory question in the General INES Rating Procedure in the INES Manual is recommended. (orig.)

Homogeneous double-layer amorphous Si-doped indium oxide thin-film transistors for control of turn-on voltage

International Nuclear Information System (INIS)

Kizu, Takio; Tsukagoshi, Kazuhito; Aikawa, Shinya; Nabatame, Toshihide; Fujiwara, Akihiko; Ito, Kazuhiro; Takahashi, Makoto

2016-01-01

We fabricated homogeneous double-layer amorphous Si-doped indium oxide (ISO) thin-film transistors (TFTs) with an insulating ISO cap layer on top of a semiconducting ISO bottom channel layer. The homogeneously stacked ISO TFT exhibited high mobility (19.6 cm"2/V s) and normally-off characteristics after annealing in air. It exhibited normally-off characteristics because the ISO insulator suppressed oxygen desorption, which suppressed the formation of oxygen vacancies (V_O) in the semiconducting ISO. Furthermore, we investigated the recovery of the double-layer ISO TFT, after a large negative shift in turn-on voltage caused by hydrogen annealing, by treating it with annealing in ozone. The recovery in turn-on voltage indicates that the dense V_O in the semiconducting ISO can be partially filled through the insulator ISO. Controlling molecule penetration in the homogeneous double layer is useful for adjusting the properties of TFTs in advanced oxide electronics.

New, national bottom-up estimate for tree-based biological ...

Science.gov (United States)

Nitrogen is a limiting nutrient in many ecosystems, but is also a chief pollutant from human activity. Quantifying human impacts on the nitrogen cycle and investigating natural ecosystem nitrogen cycling both require an understanding of the magnitude of nitrogen inputs from biological nitrogen fixation (BNF). A bottom-up approach to estimating BNF—scaling rates up from measurements to broader scales—is attractive because it is rooted in actual BNF measurements. However, bottom-up approaches have been hindered by scaling difficulties, and a recent top-down approach suggested that the previous bottom-up estimate was much too large. Here, we used a bottom-up approach for tree-based BNF, overcoming scaling difficulties with the systematic, immense (>70,000 N-fixing trees) Forest Inventory and Analysis (FIA) database. We employed two approaches to estimate species-specific BNF rates: published ecosystem-scale rates (kg N ha-1 yr-1) and published estimates of the percent of N derived from the atmosphere (%Ndfa) combined with FIA-derived growth rates. Species-specific rates can vary for a variety of reasons, so for each approach we examined how different assumptions influenced our results. Specifically, we allowed BNF rates to vary with stand age, N-fixer density, and canopy position (since N-fixation is known to require substantial light).Our estimates from this bottom-up technique are several orders of magnitude lower than previous estimates indicating

A Randomized Comparison of the Biomechanical Effect of Two Commercially Available Rocker Bottom Shoes to a Conventional Athletic Shoe During Walking in Healthy Individuals.

Science.gov (United States)

Talaty, Mukul; Patel, Sona; Esquenazi, Alberto

2016-01-01

Rocker bottom shoes have recently gained considerable popularity, likely in part because of the many purported benefits, including reducing joint loading and toning muscles. Scientific inquiry about these benefits has not kept pace with the increased usage of this shoe type. A fundamental premise of rocker bottom shoes is that they transform hard, flat, level surfaces into more uneven ones. Published studies have described a variety of such shoes-all having a somewhat rounded bottom and a cut heel region or a cut forefoot region, or both (double rocker). Despite the fundamentally similar shoe geometries, the reported effects of rocker bottom shoes on gait biomechanics have varied considerably. Ten healthy subjects agreed to participate in the present study and were given appropriately sized Masai Barefoot Technology (St. Louis, MO), Skechers(™) (Manhattan Beach, CA), and New Balance (Boston, MA) conventional walking shoes. After a 12-day accommodation period, the subjects walked wearing each shoe while 3-dimensional motion and force data were collected in the gait laboratory. The key findings included (1) increased trunk flexion, decreased ankle plantarflexion range, and reduced plantarflexion moment in the early stance; (2) increased ankle dorsiflexion and knee flexor moment in the midstance; (3) decreased peak ankle plantarflexion in the late stance; and (4) decreased ankle plantarflexion and decreased hip flexor and knee extensor moments in the pre-swing and into swing phase. The walking speed was unconstrained and was maintained across all shoe types. A biomechanical explanation is suggested for the observed changes. Suggestions for cautions are provided for using rocker bottom shoes in patients with neuromuscular insufficiency. Copyright © 2016 American College of Foot and Ankle Surgeons. Published by Elsevier Inc. All rights reserved.

Out-pile test of the capsule with cone shape bottom structures

Energy Technology Data Exchange (ETDEWEB)

Choi, M. H.; Kang, Y. H.; Cho, M. S.; Choo, K. N.; Kim, B. G.; Son, J. M.; Park, S. J.; Shin, Y. T.; Oh, J. M

2004-01-01

The design modification of bottom guide structures for the instrumented capsule which is used for the irradiation test in the research reactor, HANARO is done because of the cutting trouble of the bottom guide arm's pin. The previous structure of the 3-pin arm shape is changed into one body of the cone shape. The specimens of the bottom end cap ring with three different sizes ({phi}68mm, {phi}70mm, {phi}72mm) are designed and manufactured. The out-pile test for the capsule with previous 3-pin arm and new three bottom structures of the cone shape is performed using the one-channel flow test facilities. In order to estimate the compatibility with HANARO, the structural stability and integrity of the capsule, the out-pile test such as a loading/unloading test, a pressure drop test, a thermal performance test, a displacement measurement due to a vibration and an endurance test etc. is conducted, and the outer diameter of the bottom end cap ring to meet the HANARO requirements is selected. From out-pile test results the capsule with cone shape bottom structures is evaluated as to have the structural stability and the benefit from the fluid's flow respect. Also the size satisfied various requirements among three kinds of bottom end cap rings is 70mm in diameter. It is expected that the new bottom structures of the cone shape with 70mm in diameter will be applicable to all material and special capsules which will be designed and manufactured for the purpose of irradiation tests in the future.

Double hard scattering without double counting

Energy Technology Data Exchange (ETDEWEB)

Diehl, Markus [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Gaunt, Jonathan R. [VU Univ. Amsterdam (Netherlands). NIKHEF Theory Group; Schoenwald, Kay [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany)

2017-02-15

Double parton scattering in proton-proton collisions includes kinematic regions in which two partons inside a proton originate from the perturbative splitting of a single parton. This leads to a double counting problem between single and double hard scattering. We present a solution to this problem, which allows for the definition of double parton distributions as operator matrix elements in a proton, and which can be used at higher orders in perturbation theory. We show how the evaluation of double hard scattering in this framework can provide a rough estimate for the size of the higher-order contributions to single hard scattering that are affected by double counting. In a numeric study, we identify situations in which these higher-order contributions must be explicitly calculated and included if one wants to attain an accuracy at which double hard scattering becomes relevant, and other situations where such contributions may be neglected.

Double hard scattering without double counting

International Nuclear Information System (INIS)

Diehl, Markus; Gaunt, Jonathan R.

2017-02-01

Double parton scattering in proton-proton collisions includes kinematic regions in which two partons inside a proton originate from the perturbative splitting of a single parton. This leads to a double counting problem between single and double hard scattering. We present a solution to this problem, which allows for the definition of double parton distributions as operator matrix elements in a proton, and which can be used at higher orders in perturbation theory. We show how the evaluation of double hard scattering in this framework can provide a rough estimate for the size of the higher-order contributions to single hard scattering that are affected by double counting. In a numeric study, we identify situations in which these higher-order contributions must be explicitly calculated and included if one wants to attain an accuracy at which double hard scattering becomes relevant, and other situations where such contributions may be neglected.

Detection of Higgs bosons decaying to bottom quarks

International Nuclear Information System (INIS)

Gilman, F.J.; Price, L.E.

1986-11-01

Several developments affecting the possibility of Higgs detection are discussed. These include the level of certainty about the t quark mass, Monte Carlo programs to generate both signal and background events, and separation and/or enhancement of heavy quark jets from jets due to light quarks or gluons, and the possibility that the neutral Higgs decay into bottom quarks might be the decay mode of choice for detecting the intermediate mass Higgs. Possible means of detection of an intermediate mass Higgs at the SSC, particularly if a prominent decay mode is to bottom quarks, are examined, using the PYTHIA Monte Carlo program to generate both signal and background events. For the signal, events were generated in which Higgs bosons are created in proton-proton collisions, with the Higgs decaying into bottom quarks. The presence of W or Z bosons, created in the same proton-proton collision, is used to enhance the likelihood of Higgs production and to reduce the potentially enormous background. It is found that the Higgs decay to bottom quarks, if important, would be more favorable for detection of the Higgs than decay to top quarks was found to be because of the smaller background. 3 refs., 4 figs

Influence of bottom ash of palm oil on compressive strength of concrete

Science.gov (United States)

Saputra, Andika Ade Indra; Basyaruddin, Laksono, Muhamad Hasby; Muntaha, Mohamad

2017-11-01

The technological development of concrete demands innovation regarding the alternative material as a part of the effort in improving quality and minimizing reliance on currently used raw materials such as bottom ash of palm oil. Bottom ash known as domestic waste stemming from palm oil cultivation in East Kalimantan contains silica. Like cement in texture and size, bottom ash can be mixed with concrete in which the silica in concrete could help increase the compressive strength of concrete. This research was conducted by comparing between normal concrete and concrete containing bottom ash as which the materials were apart of cement replacement. The bottom ash used in this research had to pass sieve size (#200). The composition tested in this research involved ratio between cement and bottom ash with the following percentages: 100%: 0%, 90%: 10%, 85%: 15% and 80%: 20%. Planned to be within the same amount of compressive strength (fc 25 MPa), the compressive strength of concrete was tested at the age of 7, 14, and 28 days. Research result shows that the addition of bottom ash to concrete influenced workability in concrete, but it did not significantly influence the compressive strength of concrete. Based on the result of compressive strength test, the optimal compressive strength was obtained from the mixture of 100% cement and 0% bottom ash.

Decay of the Bottom mesons

International Nuclear Information System (INIS)

Duong Van Phi; Duong Anh Duc

1992-12-01

The channels of the decay of Bottom mesons are deduced from a selection rule and the Lagrangians which are formed on the LxO(4) invariance and the principle of minimal structure. The estimation of the corresponding decay probabilities are considered. (author). 21 refs

Ocean bottom seismometer technology

Science.gov (United States)

Prothero, William A., Jr.

Seismometers have been placed on the ocean bottom for about 45 years, beginning with the work of Ewing and Vine [1938], and their current use to measure signals from earthquakes and explosions constitutes an important research method for seismological studies. Approximately 20 research groups are active in the United Kingdom, France, West Germany, Japan, Canada, and the United States. A review of ocean bottom seismometer (OBS) instrument characteristics and OBS scientific studies may be found in Whitmarsh and Lilwall [1984]. OBS instrumentation is also important for land seismology. The recording systems that have been developed have been generally more sophisticated than those available for land use, and several modern land seismic recording systems are based on OBS recording system designs.The instrumentation developed for OBS work was the topic of a meeting held at the University of California, Santa Barbara, in July 1982. This article will discuss the state of the art of OBS Technology, some of the problems remaining to be solved, and some of the solutions proposed and implemented by OBS scientists and engineers. It is not intended as a comprehensive review of existing instrumentation.

Experimental Investigation of Discharge Coefficient in Mesh Panel Bottom Intakes

Directory of Open Access Journals (Sweden)

keivan bina

2012-04-01

Full Text Available Bottom racks is a hydraulic structure which is placed in the bed of stream through which, part of flow in the main channel is diverted. These structures have very wide application in industry, irrigation, drainage and etc. Of course much attention had been paid to the study of such structures, but characteristics of flow through bottom racks are complex. The present study was directed to estimate the discharge coefficient of a new kind of bottom racks including both transverse and longitudinal bars that named "mesh panel racks" without considering any solids in the fluid. This kind of bottom intake has advantages from structural point of view and has less deformation under static and dynamic loads. Laboratory setup with three mesh panel intakes was built and the effects of various parameters such as racks slope, porosity and geometry were explored. A dimensional analysis using Buckingham theory showed the effective hydraulic and geometric factors that affect the discharge coefficient (Cd of bottom racks. Then, a statistical approach to determine the discharge coefficient of a rack structure was developed with linear and nonlinear regression using SPSS software. The efficiency of the proposed technique is high enough that the associated error is limited to 10%. Finally, hydraulic performance of mesh panel intakes was compared with regular type of bottom intakes, which consist of longitudinal bars. For this purpose, diverted discharge through both type of intakes calculated in same situation

Constructing bottom barriers with met grouting

International Nuclear Information System (INIS)

Shibazaki, M.; Yoshida, H.

1997-01-01

Installing a bottom barrier using conventional high pressure jetting technology and ensuring barrier continuity is challenging. This paper describes technology that has been developed and demonstrated for the emplacement of bottom barriers using pressures and flow rates above the conventional high pressure jetting parameters. The innovation capable of creating an improved body exceeding 5 meters in diameter has resulted in the satisfying connection and adherence between the treated columns. Besides, the interfaces among the improved bodies obtain the same strength and permeability lower than 1 x 10 -7 cm/sec as body itself. A wide variety of the thickness and the diameter of the improved mass optimizes the application, and the method is nearing completion. The paper explains an aspect and briefs case histories

Properties of the Water Column and Bottom Derived from AVIRIS Data

Science.gov (United States)

Lee, Zhong-Ping; Carder, Kendall L.; Chen, F. Robert; Peacock, Thomas G.

2001-01-01

Using AVIRIS data as an example, we show in this study that the optical properties of the water column and bottom of a large, shallow area can be adequately retrieved using a model-driven optimization technique. The simultaneously derived properties include bottom depth, bottom albedo, and water absorption and backscattering coefficients, which in turn could be used to derive concentrations of chlorophyll, dissolved organic matter, and suspended sediments. The derived bottom depths were compared with a bathymetry chart and a boat survey and were found to agree very well. Also, the derived bottom-albedo image shows clear spatial patterns, with end members consistent with sand and seagrass. The image of absorption and backscattering coefficients indicates that the water is quite horizontally mixed. These results suggest that the model and approach used work very well for the retrieval of sub-surface properties of shallow-water environments even for rather turbid environments like Tampa Bay, Florida.

Eco-friendly porous concrete using bottom ash aggregate for marine ranch application.

Science.gov (United States)

Lee, Byung Jae; Prabhu, G Ganesh; Lee, Bong Chun; Kim, Yun Yong

2016-03-01

This article presents the test results of an investigation carried out on the reuse of coal bottom ash aggregate as a substitute material for coarse aggregate in porous concrete production for marine ranch applications. The experimental parameters were the rate of bottom ash aggregate substitution (30%, 50% and 100%) and the target void ratio (15%, 20% and 25%). The cement-coated granular fertiliser was substituted into a bottom ash aggregate concrete mixture to improve marine ranch applications. The results of leaching tests revealed that the bottom ash aggregate has only a negligible amount of the ten deleterious substances specified in the Ministry of Environment - Enforcement Regulation of the Waste Management Act of Republic Korea. The large amount of bubbles/air gaps in the bottom ash aggregate increased the voids of the concrete mixtures in all target void ratios, and decreased the compressive strength of the porous concrete mixture; however, the mixture substituted with 30% and 10% of bottom ash aggregate and granular fertiliser, respectively, showed an equal strength to the control mixture. The sea water resistibility of the bottom ash aggregate substituted mixture was relatively equal to that of the control mixture, and also showed a great deal of improvement in the degree of marine organism adhesion compared with the control mixture. No fatality of fish was observed in the fish toxicity test, which suggested that bottom ash aggregate was a harmless material and that the combination of bottom ash aggregate and granular fertiliser with substitution rates of 30% and 10%, respectively, can be effectively used in porous concrete production for marine ranch application. © The Author(s) 2015.

Monitoring of metals in Tilapia nilotica tissues, bottom sediments ...

African Journals Online (AJOL)

Tilapia (Tilapia nilotica), bottom sediments and water were collected from Nworie River and Oguta Lake. The muscle, liver and gills of the fish as well as the bottom sediments and water were analysed for Al, Cr, Cd, Pb, As, Zn, Mn, Co, Se, Cu, Ni and Fe using atomic absorption spectrophotometer to highlight the importance ...

A plea for Global Health Action bottom-up

Directory of Open Access Journals (Sweden)

Ulrich Laaser

2016-10-01

Full Text Available This opinion piece focuses on global health action by hands-on bottom-up practice: Initiation of an organizational framework and securing financial efficiency are – however - essential, both clearly a domain of well trained public health professionals. Examples of action are cited in the four main areas of global threats: planetary climate change, global divides and inequity, global insecurity and violent conflicts, global instability and financial crises. In conclusion a stable health systems policy framework would greatly enhance success. However, such organisational framework dries out if not linked to public debates channelling fresh thoughts and controversial proposals: the structural stabilisation is essential but has to serve not to dominate bottom-up activities. In other words a horizontal management is required, a balanced equilibrium between bottom-up initiative and top-down support. Last not least rewarding voluntary and charity work by public acknowledgement is essential.

OIL DECONTAMINATION OF BOTTOM SEDIMENTS EXPERIMENTAL WORK RESULTS

Directory of Open Access Journals (Sweden)

Lushnikov Sergey V.

2006-08-01

Full Text Available This article presents the results of experimental work during 2004-2005 on oil decontamination of bottom sediments of Lake Schuchye, situated in the Komi Republic (Northern Russia. The cause of thecontamination were huge oil spills occurred after a series of accidental ruptures on the Harjaga-Usinsk and Vozej-Usinsk oil-pipe lines in 1994. Flotation technology was used for the cleaning of bottom sediments.157 tons of crude oil were removed during the course of 2-year experimental work from an area of 4,1 ha.The content of aliphatic and alicyclic oil hydrocarbons was reduced from 53,3 g/kg to 2,2 g/kg, on average.Hydrobiological investigations revealed that bottom sediments started to be inhabited by benthos organisms, dominantly Oligochaeta. Besides Oligochaeta, Chironomidae maggots and Bivalvia were detected. Theappearance of Macrozoobenthos organisms can serve as a bioindicator of water quality.

Evaluation of aseismic integrity in HTTR core-bottom structure. Pt. 1. Aseismic test for core-bottom structure

International Nuclear Information System (INIS)

Iyoku, T.; Futakawa, M.; Ishihara, M.

1994-01-01

The aseismic tests were carried out using (1)/(5)-scale and (1)/(3)-scale models of the core-bottom structure of the HTTR to quantitatively evaluate the response of acceleration, strain, impact load etc. The following conclusions are obtained. (i) The frequency response of the keyway strain is correlative with that of the impact acceleration on the hot plenum block. (ii) It was confirmed through (1)/(5)-scale and (1)/(3)-scale model tests that the applied similarity law is valid to evaluate the seismic response characteristics of the core-bottom structure. (ii) The stress of graphite components estimated from the scale model test using S 2 -earthquake excitation was sufficiently lower than the allowable stress used as the design criterion. ((orig.))

12 Trace Metals Distribution in Fish Tissues, Bottom Sediments and ...

African Journals Online (AJOL)

`123456789jkl''''#

Abstract. Water samples, bottom sediments, Tilapia, and Cat Fish from Okumeshi River in Delta state of Nigeria were analysed ... Keywords: Trace metals, Fish Tissues, Water, Bottom sediments, Okumeshi River. Introduction ..... Grey Mangroove Avicemmia marina (Forsk). ... sewage treatment plant oulet pipe extension on.

Effect of bottom slope on the nonlinear triad interactions in shallow water

Science.gov (United States)

Chen, Hongzhou; Tang, Xiaocheng; Zhang, Ri; Gao, Junliang

2018-05-01

This paper aims at investigating the effect of bottom slope to the nonlinear triad interactions for irregular waves propagating in shallow water. The physical experiments are conducted in a wave flume with respect to the transformation of waves propagating on three bottom slopes ( β = 1/15, 1/30, and 1/45). Irregular waves with different type of breaking that are mechanically generated based on JONSWAP spectra are used for the test. The obviously different variations of spectra measured on each bottom reveal a crucial role of slope effect in the energy transfer between harmonics. The wavelet-based bispectrum were used to examine the bottom slope effect on the nonlinear triad interactions. Results show that the different bottom slopes which waves are propagated on will cause a significant discrepancy of triad interactions. Then, the discussions on the summed bicoherence which denote the distribution of phase coupling on each frequency further clarify the effect of bottom slope. Furthermore, the summed of the real and imaginary parts of bispectrum which could reflect the intensity of frequency components participating in the wave skewness and asymmetry were also investigated. Results indicate that the value of these parameters will increase as the bottom slope gets steeper.

Bottom Scour Observed Under Hurricane Ivan

National Research Council Canada - National Science Library

Teague, William J; Jarosz, Eva; Keen, Timothy R; Wang, David W; Hulbert, Mark S

2006-01-01

Observations that extensive bottom scour along the outer continental shelf under Hurricane Ivan resulted in the displacement of more than 100 million cubic meters of sediment from a 35x15 km region...

Sorption behaviour of cobalt-60 on Suez Canal bottom sediments

International Nuclear Information System (INIS)

Abdel Gawad, S.A.; El-Shinawy, R.M.K.; Abdel Malik, W.E.Y.

1981-01-01

Mineralogical, elemental analysis and sorption behaviour of the Suez Canal bottom sediments in the Port Said area were investigated. It was found that the bottom sediment consist mainly of quartz, feldspars and traces of calcite mineral. The cation-exchange capacity was found to increase as the particle size of the sediment decreased. Sorption of 60 Co by the bottom sediment increased with contact time up to 6 h. Variation of the solution pH from 4 to 9 showed limited increase in the sorption of 60 Co. As carrier concentrations increase from 10 -7 N to 10 -3 N, sorption of Co was found to increase linearly following Freundlich isotherm. The presence of Mg 2+ and Fe 3+ in solution depressed the sorption of 60 Co by the sediments. The desorption of 60 Co from bottom sediment with distilled and Suez Canal water was found to increase with contact time. (author)

A global ocean climatological atlas of the Turner angle: implications for double-diffusion and water-mass structure

Science.gov (United States)

You, Yuzhu

2002-11-01

The 1994 Levitus climatological atlas is used to calculate the Turner angle (named after J. Stewart Turner) to examine which oceanic water masses are favorable for double-diffusion in the form of diffusive convection or salt-fingering and which are doubly stable. This atlas complements the Levitus climatology. It reveals the major double-diffusive signals associated with large-scale water-mass structure. In total, about 44% of the oceans display double-diffusion, of which 30% is salt-fingering and 14% is diffusive double-diffusion. Results show that various central and deep waters are favorable for salt-fingering. The former is due to positive evaporation minus precipitation, and the latter is due to thermohaline circulation, i.e. the southward spreading of relatively warm, salty North Atlantic Deep Water (NADW) overlying cold, fresh Antarctic Bottom Water. In the northern Indian Ocean and eastern North Atlantic, favorable conditions for salt-fingering are found throughout the water column. The Red Sea (including the Persian Gulf) and Mediterranean Sea are the sources of warm, salty water for the ocean. As consequence, temperature and salinity in these outflow regions both decrease from the sea surface to the bottom. On the other hand, ocean currents are in general sluggish in these regions. In the polar and subpolar regions of Arctic and Antarctic, Okhotsk Sea, Gulf of Alaska, the subpolar gyre of the North Pacific, the Labrador Sea, and the Norwegian Sea, the upper layer water is favorable for diffusive convection because of high latitude surface cooling and ice melting. Weak and shallow diffusive convection is also found throughout tropical regions and the Bay of Bengal. The former is due to excessive precipitation over evaporation and rain cooling, and the latter is due to both precipitation and river runoff. Diffusive convection in the ocean's interior is unique to the South Atlantic between Antarctic Intermediate Water and upper NADW (uNADW). It is the

Assessment of sludges and tank bottoms treatment processes

International Nuclear Information System (INIS)

Bhutto, A.W.; Bazmi, A.A.

2005-01-01

The petroleum refining industries generate considerable amounts of sludge and tank bottoms as waste. Petroleum refinery receives crude oil containing emulsified water and solids. As the crude oil storage tanks are repeatedly filled and emptied, the water and solids settle towards the bottom as sludge. For tanks that have been in service for several years, the sludge accumulation becomes several feet deep, results in a loss of ullage in refinery crude storage tanks. The accumulation of crude storage tank bottoms is a serious problem experienced by local refineries. The refinery sludge waste is categorized as hazardous waste, which is at present buried in the tankform ground. Since the no hazardous material land filling option available, the disposal of these hazardous materials has become a major problem because of the ISO-14000 certification requirements and expectation of stakeholder. To maximize the waste oil recovery from sludge and tank bottoms and to minimize the volume of the hazardous waste, a number of waste recovery and treatment processes are available. The process designs and unit operations of each process are different and each has its own merits, in terms of the technical complexity, operation friendliness, and costs and economics. A study on each of these technologies and the subsequent tide-up to the existing unit operations is conducted, and the associated technical comparisons are made. (author)

Bottom quark contribution to spin-dependent dark matter detection

Directory of Open Access Journals (Sweden)

Jinmian Li

2016-05-01

Full Text Available We investigate a previously overlooked bottom quark contribution to the spin-dependent cross section for Dark Matter (DM scattering from the nucleon. While the mechanism is relevant to any supersymmetric extension of the Standard Model, for illustrative purposes we explore the consequences within the framework of the Minimal Supersymmetric Standard Model (MSSM. We study two cases, namely those where the DM is predominantly Gaugino or Higgsino. In both cases, there is a substantial, viable region in parameter space (mb˜−mχ≲O(100 GeV in which the bottom contribution becomes important. We show that a relatively large contribution from the bottom quark is consistent with constraints from spin-independent DM searches, as well as some incidental model dependent constraints.

Acoustic Profiling of Bottom Sediments in Large Oil Storage Tanks

Science.gov (United States)

Svet, V. D.; Tsysar', S. A.

2018-01-01

Characteristic features of acoustic profiling of bottom sediments in large oil storage tanks are considered. Basic acoustic parameters of crude oil and bottom sediments are presented. It is shown that, because of the presence of both transition layers in crude oil and strong reverberation effects in oil tanks, the volume of bottom sediments that is calculated from an acoustic surface image is generally overestimated. To reduce the error, additional post-processing of acoustic profilometry data is proposed in combination with additional measurements of viscosity and tank density distributions in vertical at several points of the tank.

Combining bottom-up and top-down

International Nuclear Information System (INIS)

Boehringer, Christoph; Rutherford, Thomas F.

2008-01-01

We motivate the formulation of market equilibrium as a mixed complementarity problem which explicitly represents weak inequalities and complementarity between decision variables and equilibrium conditions. The complementarity format permits an energy-economy model to combine technological detail of a bottom-up energy system with a second-best characterization of the over-all economy. Our primary objective is pedagogic. We first lay out the complementarity features of economic equilibrium and demonstrate how we can integrate bottom-up activity analysis into a top-down representation of the broader economy. We then provide a stylized numerical example of an integrated model - within both static and dynamic settings. Finally, we present illustrative applications to three themes figuring prominently on the energy policy agenda of many industrialized countries: nuclear phase-out, green quotas, and environmental tax reforms

Combining bottom-up and top-down

Energy Technology Data Exchange (ETDEWEB)

Boehringer, Christoph [Department of Economics, University of Oldenburg, Oldenburg (Germany); Centre for European Economic Research (ZEW), Mannheim (Germany); Rutherford, Thomas F. [Ann Arbor, Michigan (United States)

2008-03-15

We motivate the formulation of market equilibrium as a mixed complementarity problem which explicitly represents weak inequalities and complementarity between decision variables and equilibrium conditions. The complementarity format permits an energy-economy model to combine technological detail of a bottom-up energy system with a second-best characterization of the over-all economy. Our primary objective is pedagogic. We first lay out the complementarity features of economic equilibrium and demonstrate how we can integrate bottom-up activity analysis into a top-down representation of the broader economy. We then provide a stylized numerical example of an integrated model - within both static and dynamic settings. Finally, we present illustrative applications to three themes figuring prominently on the energy policy agenda of many industrialized countries: nuclear phase-out, green quotas, and environmental tax reforms. (author)

Daylighting performance evaluation of a bottom-up motorized roller shade

Energy Technology Data Exchange (ETDEWEB)

Kapsis, K.; Athienitis, A.K.; Zmeureanu, R.G. [Department of Building, Civil and Environmental Engineering, Concordia University, Montreal, QC (Canada); Tzempelikos, A. [School of Civil Engineering, Purdue University, West Lafayette, IN (United States)

2010-12-15

This paper presents an experimental and simulation study for quantifying the daylighting performance of bottom-up roller shades installed in office spaces. The bottom-up shade is a motorized roller shade that opens from top to bottom operating in the opposite direction of a conventional roller shade, so as to cover the bottom part of the window, while allowing daylight to enter from the top part of the window, reaching deeper into the room. A daylighting simulation model, validated with full-scale experiments, was developed in order to establish correlations between the shade position, outdoor illuminance and work plane illuminance for different outdoor conditions. Then, a shading control algorithm was developed for application in any location and orientation. The validated model was employed for a sensitivity analysis of the impact of shade optical properties and control on the potential energy savings due to the use of daylighting. The results showed that Daylight Autonomy for the bottom-up shade is 8-58% higher compared to a conventional roller shade, with a difference of 46% further away from the facade, where the use of electric lighting is needed most of the time. The potential reduction in energy consumption for lighting is 21-41%. (author)

Bottom up

International Nuclear Information System (INIS)

Ockenden, James

1999-01-01

This article presents an overview of the electric supply industries in Eastern Europe. The development of more competitive and efficient plant in Poland and work on emissions control ahead of EU membership; the Czech's complicated tariff system; Hungary's promised 8% return on investment in their electricity supply industry and its tariff problems; Bulgaria and Ukraine's desperate need for investment to build alternative plants to their aging nuclear plants; and demand outstripping supply in Romania are among the topics considered.. The viscous circle of poor service and low utility income is considered, and the top-down approach for breaking the cycle by improving plant efficiency, and the bottom up approach of improving plant income as practiced by Moldavia are explained. (UK)

Sediment movement along the U.S. east coast continental shelf-I. Estimates of bottom stress using the Grant-Madsen model and near-bottom wave and current measurements

Science.gov (United States)

Lyne, V.D.; Butman, B.; Grant, W.D.

1990-01-01

Bottom stress is calculated for several long-term time-series observations, made on the U.S. east coast continental shelf during winter, using the wave-current interaction and moveable bed models of Grant and Madsen (1979, Journal of Geophysical Research, 84, 1797-1808; 1982, Journal of Geophysical Research, 87, 469-482). The wave and current measurements were obtained by means of a bottom tripod system which measured current using a Savonius rotor and vane and waves by means of a pressure sensor. The variables were burst sampled about 10% of the time. Wave energy was reasonably resolved, although aliased by wave groupiness, and wave period was accurate to 1-2 s during large storms. Errors in current speed and direction depend on the speed of the mean current relative to the wave current. In general, errors in bottom stress caused by uncertainties in measured current speed and wave characteristics were 10-20%. During storms, the bottom stress calculated using the Grant-Madsen models exceeded stress computed from conventional drag laws by a factor of about 1.5 on average and 3 or more during storm peaks. Thus, even in water as deep as 80 m, oscillatory near-bottom currents associated with surface gravity waves of period 12 s or longer will contribute substantially to bottom stress. Given that the Grant-Madsen model is correct, parameterizations of bottom stress that do not incorporate wave effects will substantially underestimate stress and sediment transport in this region of the continental shelf.

Fluidized bed combustion bottom ash: A better and alternative geo-material resource for construction.

Science.gov (United States)

Mandal, A K; Paramkusam, Bala Ramudu; Sinha, O P

2018-04-01

Though the majority of research on fly ash has proved its worth as a construction material, the utility of bottom ash is yet questionable due to its generation during the pulverized combustion process. The bottom ash produced during the fluidized bed combustion (FBC) process is attracting more attention due to the novelty of coal combustion technology. But, to establish its suitability as construction material, it is necessary to characterize it thoroughly with respect to the geotechnical as well as mineralogical points of view. For fulfilling these objectives, the present study mainly aims at characterizing the FBC bottom ash and its comparison with pulverized coal combustion (PCC) bottom ash, collected from the same origin of coal. Suitability of FBC bottom ash as a dike filter material in contrast to PCC bottom ash in replacing traditional filter material such as sand was also studied. The suitability criteria for utilization of both bottom ash and river sand as filter material on pond ash as a base material were evaluated, and both river sand and FBC bottom ash were found to be satisfactory. The study shows that FBC bottom ash is a better geo-material than PCC bottom ash, and it could be highly recommended as an alternative suitable filter material for constructing ash dikes in place of conventional sand.

An efficient and not polluting bottom ash extraction system

International Nuclear Information System (INIS)

Carrea, A.

1992-01-01

This paper reports that boiler waste water effluent must meet more and more tighter requirements to comply with environmental regulations; sluice water resulting from bottom ash handling is one of the main problems in this context, and many utilities are under effort to maximize the reuse of the sluice water, and, if possible, to meet the aim of zero water discharge from bottom ash handling system. At the same time ash reuse efforts gain strength in order to minimize waste production. One solution to these problems can be found in an innovative Bottom Ash Extraction System (MAC System), marked by the peculiarity to be a continuous dry ash removal; the system has been developed in the last four years by MAGALDI INDUSTRIE SRL in collaboration with ANSALDO Ricerche, the R and D department of ANSALDO, the main Italian Boiler Manufacturer, and is now installed in six ENEL Boilers. The elimination of the water as separation element between the bottom part of the furnace and the outside atmosphere gives advantages mainly from the environmental view point, but a certain improvement in the boiler efficiency has also been demonstrated by the application of the system

Bottom-type scattering layers and equatorial spread F

Directory of Open Access Journals (Sweden)

D. L. Hysell

2004-12-01

Full Text Available Jicamarca radar observations of bottom-type coherent scattering layers in the post-sunset bottomside F-region ionosphere are presented and analyzed. The morphology of the primary waves seen in radar images of the layers supports the hypothesis of kudeki+bhattacharyya-1999 that wind-driven gradient drift instabilities are operating. In one layer event when topside spread F did not occur, irregularities were distributed uniformly in space throughout the layers. In another event when topside spread F did eventually occur, the irregularities within the pre-existing bottom-type layers were horizontally clustered, with clusters separated by about 30km. The same horizontal periodicity was evident in the radar plumes and large-scale irregularities that emerged later in the event. We surmise that horizontal periodicity in bottom-type layer irregularity distribution is indicative of large-scale horizontal waves in the bottomside F-region that may serve as seed waves for large-scale Rayleigh Taylor instabilities. Key words. Ionosphere (equatorial ionosphere; ionospheric irregularties; plasma waves and instabilities

Bottom mass from nonrelativistic sum rules at NNLL

Energy Technology Data Exchange (ETDEWEB)

Stahlhofen, Maximilian

2013-01-15

We report on a recent determination of the bottom quark mass from nonrelativistic (large-n) {Upsilon} sum rules with renormalization group improvement (RGI) at next-to-next-to-leading logarithmic (NNLL) order. The comparison to previous fixed-order analyses shows that the RGI computed in the vNRQCD framework leads to a substantial stabilization of the theoretical sum rule moments with respect to scale variations. A single moment fit (n=10) to the available experimental data yields M{sub b}{sup 1S}=4.755{+-}0.057{sub pert}{+-}0.009{sub {alpha}{sub s}}{+-}0.003{sub exp} GeV for the bottom 1S mass and anti m{sub b}(anti m{sub b})=4.235{+-}0.055{sub pert}{+-}0.003{sub exp} GeV for the bottom MS mass. The quoted uncertainties refer to the perturbative error and the uncertainties associated with the strong coupling and the experimental input.

SIMULATION OF ANALYTICAL TRANSIENT WAVE DUE TO DOWNWARD BOTTOM THRUST

Directory of Open Access Journals (Sweden)

Sugih Sudharma Tjandra

2015-11-01

Full Text Available Generation process is an important part of understanding waves, especially tsunami. Large earthquake under the sea is one major cause of tsunamis. The sea surface deforms as a response from the sea bottom motion caused by the earthquake. Analytical description of surface wave generated by bottom motion can be obtained from the linearized dispersive model. For a bottom motion in the form of a downward motion, the result is expressed in terms of improper integral. Here, we focus on analyzing the convergence of this integral, and then the improper integral is approximated into a finite integral so that the integral can be evaluated numerically. Further, we simulate free surface elevation for three different type of bottom motions, classified as impulsive, intermediate, and slow  movements. We demonstrate that the wave propagating to the right, with a depression as the leading wave, followed with subsequent wave crests. This phenomena is often observed in most tsunami events.

Safe jack-up method permits repairs of tank bottoms and foundations

International Nuclear Information System (INIS)

de Wit, J.

1991-01-01

The oil and chemical industries use many thousands of steel tanks to store crude oil, oil products, and chemical liquids. The majority of these tanks are 30-40 years old. Tank bottoms are likely to begin leaking in the coming years, as these tanks get older. The European technique of jacking up a tank and repairing its foundation allows the thorough inspection of the underside of the tank bottom and the removal of saturated foundation material. And the possibility of soil and groundwater pollution is reduced to a minimum. With good, regular maintenance, the lifetime of a storage tank is very long. But experience has shown that special attention should be paid to the tank's bottom. Tank bottoms are only 5 or 6 mm thick, and in the last 10 years, an increasing number of leaks in tank bottoms have been reported. Tank foundations are affected by these leaks. This article describes the resulting procedure, which is used successfully in many European countries, but is not yet common in the U.S

Bottom reflector for power reactors

International Nuclear Information System (INIS)

Elter, C.; Kissel, K.F.; Schoening, J.; Schwiers, H.G.

1982-01-01

In pebble bed reactors erosion and damage due fuel elements movement on the surface of the bottom reflector should be minimized. This can be achieved by chamfering and/or rounding the cover edges of the graphite blocks and the edges between the drilled holes and the surface of the graphite block. (orig.) [de

14 CFR 25.533 - Hull and main float bottom pressures.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 25... AIRCRAFT AIRWORTHINESS STANDARDS: TRANSPORT CATEGORY AIRPLANES Structure Water Loads § 25.533 Hull and main float bottom pressures. (a) General. The hull and main float structure, including frames and bulkheads...

Co-sintering of treated APC-residues with bottom ash

DEFF Research Database (Denmark)

Jensen, Dorthe Lærke; Bergfeldt, Britta; Vehlow, Jürgen

2001-01-01

the influence of co-sintering of Ferrox products with bottom ashes on the quality of the residues and the effects on the combustion process. Only few elements showed higher concentrations in the bottom ashes of these co-combustion tests compared to reference tests. No significant effect on the leaching......Air pollution control residues stabilised by means of the Ferrox process can be sager disposed of due to lower contents of soluble salts and lesssoluble heavy metals stabilised in iron oxides. Co-combustion tests in the Karlsruhe test incinerator TAMARA were carried out in order to investigate...... behaviour of the bottom ashes could be found. During the co-combustion process an increase in SO2 concentrations in the raw gas and slightly lower temperatures in the fuel bed could be observed....

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

Directory of Open Access Journals (Sweden)

Antoni

2017-01-01

Full Text Available Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment including water absorption, sieve analysis, and fineness modulus. Highvolume fly ash (HVFA mortar specimens were made and the compressive strength and flowability test using bottom ash after treatment are compared with that of the sand specimen. Low water to cementitious ratio was used to ensure higher strength from the cementitious paste and superplasticizer demand was determined for each treatment. The result showed that bottom ash can be used as fine aggregate replacement material. Sieve separation of the bottom ash could produce 75% of the compressive strength compared with the control sand specimen, whereas pounded bottom ash could have up to 96% of the compressive strength of the control specimen. A 28-day compressive strength of 45 MPa was achievable with 100% replacement of fine aggregate with bottom ash.

Ac-induced disruption of the doubleDs structure in tomato

NARCIS (Netherlands)

Rommens, Caius M.T.; Biezen, Erik A. van der; Ouwerkerk, Pieter B.F.; Nijkamp, H. John J.; Hille, Jacques

1991-01-01

The maize doubleDs element is stably maintained in the tomato genome. Upon the subsequent introduction of Ac into a plant containing doubleDs, disruption of the doubleDs structure and DNA rearrangements at the site of the doubleDs element were observed. No indications were obtained for excision of

Use of Incineration Solid Waste Bottom Ash as Cement Mixture in Cement Production

Science.gov (United States)

Jun, N. H.; Abdullah, M. M. A. B.; Jin, T. S.; Kadir, A. A.; Tugui, C. A.; Sandu, A. V.

2017-06-01

Incineration solid waste bottom ash was use to examine the suitability as a substitution in cement production. This study enveloped an innovative technology option for designing new equivalent cement that contains incineration solid waste bottom ash. The compressive strength of the samples was determined at 7, 14, 28 and 90 days. The result was compared to control cement with cement mixture containing incineration waste bottom ash where the result proved that bottom ash cement mixture able achieve its equivalent performance compared to control cement which meeting the requirement of the standards according to EN 196-1. The pozzolanic activity index of bottom ash cement mixture reached 0.92 at 28 days and 0.95 at 90 and this values can be concluded as a pozzolanic material with positive pozzolanic activity. Calcium hydroxide in Portland cement decreasing with the increasing replacement of bottom ash where the reaction occur between Ca(OH)2 and active SiO2.

Utilization of power plant bottom ash as aggregates in fiber-reinforced cellular concrete.

Science.gov (United States)

Lee, H K; Kim, H K; Hwang, E A

2010-02-01

Recently, millions tons of bottom ash wastes from thermoelectric power plants have been disposed of in landfills and coastal areas, regardless of its recycling possibility in construction fields. Fiber-reinforced cellular concrete (FRCC) of low density and of high strength may be attainable through the addition of bottom ash due to its relatively high strength. This paper focuses on evaluating the feasibility of utilizing bottom ash of thermoelectric power plant wastes as aggregates in FRCC. The flow characteristics of cement mortar with bottom ash aggregates and the effect of aggregate type and size on concrete density and compressive strength were investigated. In addition, the effects of adding steel and polypropylene fibers for improving the strength of concrete were also investigated. The results from this study suggest that bottom ash can be applied as a construction material which may not only improve the compressive strength of FRCC significantly but also reduce problems related to bottom ash waste.

Culture from the Bottom Up

Science.gov (United States)

Atkinson, Dwight; Sohn, Jija

2013-01-01

The culture concept has been severely criticized for its top-down nature in TESOL, leading arguably to its falling out of favor in the field. But what of the fact that people do "live culturally" (Ingold, 1994)? This article describes a case study of culture from the bottom up--culture as understood and enacted by its individual users.…

Physical and Chemical Properties of Coal Bottom Ash (CBA) from Tanjung Bin Power Plant

Science.gov (United States)

Izzati Raihan Ramzi, Nurul; Shahidan, Shahiron; Zulkhairi Maarof, Mohamad; Ali, Noorwirdawati

2016-11-01

The objective of this study is to determine the physical and chemical characteristics of Coal Bottom Ash (CBA) obtained from Tanjung Bin Power Plant Station and compare them with the characteristics of natural river sand (as a replacement of fine aggregates). Bottom ash is the by-product of coal combustion during the electricity generating process. However, excess bottom ash production due to the high production of electricity in Malaysia has caused several environmental problems. Therefore, several tests have been conducted in order to determine the physical and chemical properties of bottom ash such as specific gravity, density, particle size distribution, Scanning Electron Microscopic (SEM) and X- Ray Fluorescence (XRF) in the attempt to produce sustainable material from waste. The results indicated that the natural fine aggregate and coal bottom ash have very different physical and chemical properties. Bottom ash was classified as Class C ash. The porous structure, angular and rough texture of bottom ash affected its specific gravity and particle density. From the tests, it was found that bottom ash is recommended to be used in concrete as a replacement for fine aggregates.

Experimental Study on the Measurement of Water Bottom Vibration Induced by Underwater Drilling Blasting

Directory of Open Access Journals (Sweden)

Gu Wenbin

2015-01-01

Full Text Available Due to the lack of proper instrumentations and the difficulties in underwater measurements, the studies about water bottom vibration induced by underwater drilling blasting are seldom reported. In order to investigate the propagation and attenuation laws of blasting induced water bottom vibration, a water bottom vibration monitor was developed with consideration of the difficulties in underwater measurements. By means of this equipment, the actual water bottom vibration induced by underwater drilling blasting was measured in a field experiment. It shows that the water bottom vibration monitor could collect vibration signals quite effectively in underwater environments. The followed signal analysis shows that the characteristics of water bottom vibration and land ground vibration induced by the same underwater drilling blasting are quite different due to the different geological environments. The amplitude and frequency band of water bottom vibration both exceed those of land ground vibration. Water bottom vibration is mainly in low-frequency band that induced by blasting impact directly acts on rock. Besides the low-frequency component, land vibration contains another higher frequency band component that induced by followed water hammer wave acts on bank slope.

Aluminium recovery from waste incineration bottom ash, and its oxidation level.

Science.gov (United States)

Biganzoli, Laura; Grosso, Mario

2013-09-01

The recovery of aluminium (Al) scraps from waste incineration bottom ash is becoming a common practice in waste management. However, during the incineration process, Al in the waste undergoes oxidation processes that reduce its recycling potential. This article investigates the behaviour of Al scraps in the furnace of two selected grate-fired waste-to-energy plants and the amount recoverable from the bottom ash. About 21-23% of the Al fed to the furnace with the residual waste was recovered and potentially recycled from the bottom ash. Out of this amount, 76-87% was found in the bottom ash fraction above 5 mm and thus can be recovered with standard eddy current separation technology. These values depend on the characteristics and the mechanical strength of the Al items in the residual waste. Considering Al packaging materials, about 81% of the Al in cans can be recovered from the bottom ash as an ingot, but this amount decreases to 51% for trays, 27% for a mix of aluminium and poly-laminated foils and 47% for paper-laminated foils. This shows that the recovery of Al from the incineration residues increases proportionally to the thickness of the packaging.

Layered growth with bottom-spray granulation for spray deposition of drug.

Science.gov (United States)

Er, Dawn Z L; Liew, Celine V; Heng, Paul W S

2009-07-30

The gap in scientific knowledge on bottom-spray fluidized bed granulation has emphasized the need for more studies in this area. This paper comparatively studied the applicability of a modified bottom-spray process and the conventional top-spray process for the spray deposition of a micronized drug during granulation. The differences in circulation pattern, mode of growth and resultant granule properties between the two processes were highlighted. The more ordered and consistent circulation pattern of particles in a bottom-spray fluidized bed was observed to give rise to layered granule growth. This resulted in better drug content uniformity among the granule batches and within a granule batch. The processes' sensitivities to wetting and feed material characteristics were also compared and found to differ markedly. Less robustness to differing process conditions was observed for the top-spray process. The resultant bottom-spray granules formed were observed to be less porous, more spherical and had good flow properties. The bottom-spray technique can thus be potentially applied for the spray deposition of drug during granulation and was observed to be a good alternative to the conventional technique for preparing granules.

Ocean Bottom Seismic Scattering

Science.gov (United States)

1989-11-01

EPR, the Clipperton and Orozco fracture zones , and along the coast of Mexico, were recorded for a two month period using ocean bottom seismometers...67. Tuthill, J.D., Lewis, B.R., and Garmany, J.D., 1981, Stonely waves, Lopez Island noise, and deep sea noise from I to 5 hz, Marine Geophysical...Patrol Pell Marine Science Library d/o Coast Guard R & D Center University of Rhode Island Avery Point Narragansett Bay Campus Groton, CT 06340

Prospects of obtaining samples of bottom sediments from subglacial lake Vostok

Directory of Open Access Journals (Sweden)

Н. И. Васильев

2017-04-01

Full Text Available The paper proves the timeliness of obtaining and examining bottom sediments from subglacial Lake Vostok. Predictive geological section of Lake Vostok and information value of bottom sediments have been examined. Severe requirements towards environmental security of lake examinations and sampling of bottom sediments rule out the use of conventional drilling technologies, as they would pollute the lake with injection liquid from the borehole. In order to carry out sampling of bottom sediments from the subglacial lake, it is proposed to use a dynamically balanced tool string, which enables rotary drilling without any external support on borehole walls to transmit counter torque.     A theoretical analysis has been carried out to assess the operation of the tool string, which is a two-mass oscillatory electromechanical system of reciprocating and rotating motion (RRM with two degrees of freedom.

Area-intensive bottom culture production of blue mussels, Mytilus edulis (L.)

DEFF Research Database (Denmark)

Christensen, Helle Torp

column have the potential to become an alternative seed source for mussel production in bottom cultures. When compared to mussels collected from natural benthic mussel beds, suspended mussels had an active predator response by developing a significantly stronger attach-ment to the substrate and having...... a more pronounced aggregation behaviour. Bottom mussels exhibited a passive strategy by developing a thicker shell and larger relative size of the posterior adductor muscle. When comparing the performance of suspended and bottom seed mussels on complex and smooth sub-strate, respectively, originally...

Comparative Study of the Use of Different Biomass Bottom Ash in the Manufacture of Ceramic Bricks

OpenAIRE

Eliche-Quesada, D; Felipe Sesé, Manuel Ángel (UNIR); Martínez-Martínez, S; Pérez-Villarejo, L

2017-01-01

The present study evaluates the suitability of several types of biomass bottom ashes [wood bottom ash (WBA), pine-olive pruning bottom ash (POPBA), olive stone bottom ash (OSBA), and olive pomace bottom ash (OPBA)] as an alternative source to replace ceramic raw material in the production of clay bricks. The clay and biomass bottom ash were characterized by means of X-ray diffraction (XRD) (crystallinity), X-ray fluorescence spectroscopy (XRF) (chemical composition), carbon, nitrogen, hydroge...

Construction of reactor vessel bottom of prestressed reinforced concrete

International Nuclear Information System (INIS)

Sitnikov, M.I.; Metel'skij, V.P.

1980-01-01

Methods are described for building reactor vessel bottoms of prestressed reinforced concrete during NPPs construction in Great Britain, France, Germany (F.R.) and the USA. Schematic of operations performed in succession is presented. Considered are different versions of one of the methods for concreting a space under a facing by forcing concrete through a hole in the facing. The method provides tight sticking of the facing to the reactor vessel bottom concrete

14 CFR 23.533 - Hull and main float bottom pressures.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Hull and main float bottom pressures. 23... Water Loads § 23.533 Hull and main float bottom pressures. (a) General. The hull and main float....00213; K2=hull station weighing factor, in accordance with figure 2 of appendix I of this part; VS1...

Landfilling: Bottom Lining and Leachate Collection

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Manfredi, Simone; Kjeldsen, Peter

2011-01-01

from entering the groundwater or surface water. The bottom lining system should cover the full footprint area of the landfill, including both the relatively flat bottom and the sideslopes in the case of an excavated configuration. This prevents the lateral migration of leachate from within the landfill...... triple) liners, are extremely effective in preventing leachate from entering into the environment. In addition, the risk of polluting the groundwater at a landfill by any leakage of leachate depends on several factors related to siting of the landfill: distance to the water table, distance to surface...... water bodies, and the properties of the soil beneath the landfill. In addition to the lining and drainage systems described in this chapter, the siting and hydrogeology of the landfill site (Chapter 10.12) and the top cover (Chapter 10.9) are also part of the barrier system, contributing to reducing...

Experimental Study on the Measurement of Water Bottom Vibration Induced by Underwater Drilling Blasting

OpenAIRE

Wenbin, Gu; Jianghai, Chen; Zhenxiong, Wang; Zhihua, Wang; Jianqing, Liu; Ming, Lu

2015-01-01

Due to the lack of proper instrumentations and the difficulties in underwater measurements, the studies about water bottom vibration induced by underwater drilling blasting are seldom reported. In order to investigate the propagation and attenuation laws of blasting induced water bottom vibration, a water bottom vibration monitor was developed with consideration of the difficulties in underwater measurements. By means of this equipment, the actual water bottom vibration induced by underwater ...

Classification of bottom composition and bathymetry of shallow waters by passive remote sensing

Science.gov (United States)

Spitzer, D.; Dirks, R. W. J.

The use of remote sensing data in the development of algorithms to remove the influence of the watercolumn on upwelling optical signals when mapping the bottom depth and composition in shallow waters. Calculations relating the reflectance spectra to the parameters of the watercolumn and the diverse bottom types are performed and measurements of the underwater reflection coefficient of sandy, mud, and vegetation-type seabottoms are taken. The two-flow radiative transfer model is used. Reflectances within the spectral bands of the Landsat MSS, the Landsat TM, SPOT HVR, and the TIROS-N series AVHRR were computed in order to develop appropriate algorithms suitable for the bottom depth and type mapping. Bottom depth and features appear to be observable down to 3-20 m depending on the water composition and bottom type.

Double trisomy (48,XXX,+18) with features of Roberts syndrome

Energy Technology Data Exchange (ETDEWEB)

Descartes, M.; Longshore, J.W.; Crawford, E. [Univ. of Alabama, Birmingham, AL (United States)] [and others

1994-09-01

We report an infant with double trisomy 48,XXX,+18, who also displayed features of Roberts syndrome. All previously published cases with similar double trisomy have presented with features of trisomy 18 syndrome. The chromosome analysis done at birth revealed the double trisomy; parental chromosomes were normal. The proband presented with microbrachycephaly, unilateral cleft lip and palate, choanal atresia, midfacial capillary hemanioma, thin nares, shallow orbits, malformed ears, sparse hair, hypomelia of the upper limbs, rocker-bottom feet, auricular septal defect and agenesis of the corpus callosum. Characteristic features of Roberts syndrome included hypomelia, midfacial defects, and severe growth deficiency. Among the many different features reported in the literature for patients with trisomy 18 syndrome, the most consistent were growth deficiency, clenched fingers and congenital heart defects (e.g. VSD, ASD, PDA). Although some of our patient`s features such as cleft lip and cleft palate, low-set malformed ears, ASD, defects of the corpus callosum, choanal atresia, radial aplasia could also be seen in trisomy 18 syndrome (in 10-50% of the cases), her phenotype was more typical of Roberts syndrome because of symmetrical hypomelia and midfacial defects. Our patient`s chromosomes did not show premature separation of centromeric heterochromatin, a feature reported to occur in approximately one-half of individuals with Roberts syndrome. Sporadic aneuploidy involving different chromosomes has been found in lymphocyte cultures from some Roberts syndrome patients and is considered by some authors as a mitotic mutant. This aneuploidy is most likely to be chromosome gain. The simultaneous occurrence of trisomy X and 18 is extremely rare with only 11 cases having been reported in the literature. Our patient is unique since she has the double trisomy in addition to the characteristic features of Roberts syndrome.

Combining Top-down and Bottom-up Accountability: Evidence from a Bribery Experiment.

OpenAIRE

Danila Serra

2008-01-01

Monitoring corruption typically relies on top-down interventions aimed at increasing the probability of external controls and the severity of punishment. An alternative approach to fighting corruption is to induce bottom-up pressure for reform. Recent studies have shown that both top-down and bottom-up mechanisms are rarely able to keep service providers accountable. This paper investigates the effectiveness of an accountability system that combines bottom-up monitoring and top-down auditing ...

Quality assurance of MSWI bottom ash. Environmental properties; Kvalitetssaekring av slaggrus. Miljoemaessiga egenskaper

Energy Technology Data Exchange (ETDEWEB)

Flyhammar, Peter [Lund Univ. (Sweden). Dept. of Engineering Geology

2006-04-15

In Sweden several hundred tonnes of MSWI bottom ash are generated annually at 29 incineration plants for municipal solid waste. So far bottom ash has mainly been disposed in to landfills or used as cover material in landfills or in other construction works at landfills. A few applications of bottom ash in construction works outside landfills have been reported. A large problem for the market of bottom ash and other secondary materials outside Swedish waste treatment plants is the lack of roles and regulations for a non-polluting use. During 2002 Hartlen and Groenholm (HG) presented a proposal to a system to assure the quality of bottom ash after homogenization and stabilization. A quality assurance of environmental properties should be based on leaching tests. The aim of this project was to study how the control of environmental properties of bottom ash earlier described in e.g. a product information sheet should be worked out. The starting-point has been a control system for bottom ash developed by the Sysav company. Different leaching tests illustrate however different aspects of the environmental properties, e.g. short-term and long-term leaching. Limit and target values for different variables could affect both the possibilities to use bottom ash as well as the sampling from storage heaps. We have chosen to investigate: pH, availability and leached amount and the connection between these variables; the possibilities to use pH or the availability to assess both short-term and long term leaching properties; how the number of subsamples that should be collected from a storage heap is affected by different control variables and quality requirements; how bottom ash is stabilized by today's storage technology and how the technology could be improved. Our sample test of bottom ash from Swedish incineration plants indicates that the availability of elements such as Cd, Cu, Cr, Ni, Pb and Zn in bottom ash usually is below Sysav's target values. Extreme values

Bottom fauna of the Malacca Strait

Digital Repository Service at National Institute of Oceanography (India)

Parulekar, A.H.; Ansari, Z.A.

Bottom fauna of Malacca Strait (connecting the Indian Ocean with Pacific) in the depth range of 80 to 1350 m, is dominated by meiofauna which exceeds macrofauna by 12.5 times in weight and by more than 780 times in population density. Standing crop...

Treated bottom ash medium and method of arsenic removal from drinking water

Science.gov (United States)

Gadgil, Ashok

2009-06-09

A method for low-cost arsenic removal from drinking water using chemically prepared bottom ash pre-treated with ferrous sulfate and then sodium hydroxide. Deposits on the surface of particles of bottom ash form of activated iron adsorbent with a high affinity for arsenic. In laboratory tests, a miniscule 5 grams of pre-treated bottom ash was sufficient to remove the arsenic from 2 liters of 2400 ppb (parts per billion) arsenic-laden water to a level below 50 ppb (the present United States Environmental Protection Agency limit). By increasing the amount of pre-treated bottom ash, even lower levels of post-treatment arsenic are expected. It is further expected that this invention supplies a very low-cost solution to arsenic poisoning for large population segments.

Flowable Backfill Materials from Bottom Ash for Underground Pipeline

Directory of Open Access Journals (Sweden)

Kyung-Joong Lee

2014-04-01

Full Text Available The purpose of this study was to investigate the relationship between strength and strain in manufacturing controlled low strength materials to recycle incineration bottom ash. Laboratory tests for controlled low strength materials with bottom ash and recycled in-situ soil have been carried out. The optimum mixing ratios were 25%–45% of in-situ soil, 30% of bottom ash, 10%–20% of fly ash, 0%–3% of crumb rubber, 3% of cement, and 22% of water. Each mixture satisfied the standard specifications: a minimum 20 cm of flowability and 127 kPa of unconfined compressive strength. The average secant modulus (E50 was (0.07–0.08 qu. The ranges of the internal friction angle and cohesion for mixtures were 36.5°–46.6° and 49.1–180 kPa, respectively. The pH of all of the mixtures was over 12, which is strongly alkaline. Small-scale chamber tests for controlled low strength materials with bottom ash and recycled in-situ soil have been carried out. Vertical deflection of 0.88–2.41 mm and horizontal deflection of 0.83–3.72 mm were measured during backfilling. The vertical and horizontal deflections of controlled low strength materials were smaller than that of sand backfill.

Quality assurance of MSWI bottom ash. Environmental properties; Kvalitetssaekring av slaggrus. Miljoemaessiga egenskaper

Energy Technology Data Exchange (ETDEWEB)

Flyhammar, Peter [Lund Univ. (Sweden). Engineering Geology

2006-04-15

In Sweden, several hundred tonnes of MSWI bottom ash are generated annually at 29 incineration plants for municipal solid waste. So far bottom ash has mainly been disposed in to landfills or used as cover material in landfills or in other construction works at landfills. A few applications of bottom ash in construction works outside landfills have been reported. A large problem for the market of bottom ash and other secondary materials outside Swedish waste treatment plants is the lack of roles and regulations for a non-polluting use. During 2002 Hartlen and Groenholm presented a proposal to a system to assure the quality of bottom ash after homogenization and stabilization. They notice that the leaching of salts and metals to ground water constitutes the largest risk for the environment during use of bottom ash. Therefore, a quality assurance of environmental properties should be based on leaching tests. The aim of this project was to study how the control of environmental properties of bottom ash (at first hand leaching properties) earlier described in e.g. a product information sheet should be worked out. The starting-point has been a control system for bottom ash developed by Sysav. Different leaching tests illustrate however different aspects of the environmental properties, e.g. short-term and long-term leaching. Limit and target values for different variables could affect both the possibilities to use bottom ash as well as the sampling from storage heaps. We have chosen to investigate pH, availability and leached amount and the connection between these variables. the possibilities to use pH or the availability to assess both short-term and longterm leaching properties. how the number of subsamples that should be collected from a storage heap is affected by different control variables and quality requirements. how bottom ash is stabilized by today's storage technology and how the technology could be improved. Our sample test of bottom ash from Swedish

Where to start? Bottom-up attention improves working memory by determining encoding order.

Science.gov (United States)

Ravizza, Susan M; Uitvlugt, Mitchell G; Hazeltine, Eliot

2016-12-01

The present study aimed to characterize the mechanism by which working memory is enhanced for items that capture attention because of their novelty or saliency-that is, via bottom-up attention. The first experiment replicated previous research by corroborating that bottom-up attention directed to an item is sufficient for enhancing working memory and, moreover, generalized the effect to the domain of verbal working memory. The subsequent 3 experiments sought to determine how bottom-up attention affects working memory. We considered 2 hypotheses: (1) Bottom-up attention enhances the encoded representation of the stimulus, similar to how voluntary attention functions, or (2) It affects the order of encoding by shifting priority onto the attended stimulus. By manipulating how stimuli were presented (simultaneous/sequential display) and whether the cue predicted the tested items, we found evidence that bottom-up attention improves working memory performance via the order of encoding hypothesis. This finding was observed across change detection and free recall paradigms. In contrast, voluntary attention improved working memory regardless of encoding order and showed greater effects on working memory. We conclude that when multiple information sources compete, bottom-up attention prioritizes the location at which encoding should begin. When encoding order is set, bottom-up attention has little or no benefit to working memory. (PsycINFO Database Record (c) 2016 APA, all rights reserved).

ICT-ENABLED BOTTOM-UP ARCHITECTURAL DESIGN

Directory of Open Access Journals (Sweden)

Burak Pak

2016-04-01

Full Text Available This paper aims at discussing the potentials of bottom-up design practices in relation to the latest developments in Information and Communication Technologies (ICT by making an in-depth review of inaugural cases. The first part of the study involves a literature study and the elaboration of basic strategies from the case study. The second part reframes the existing ICT tools and strategies and elaborates on their potentials to support the modes of participation performed in these cases. As a result, by distilling the created knowledge, the study reveals the potentials of novel modes of ICT-enabled design participation which exploit a set of collective action tools to support sustainable ways of self-organization and bottom-up design. The final part explains the relevance of these with solid examples and presents a hypothetical case for future implementation. The paper concludes with a brief reflection on the implications of the findings for the future of architectural design education.

Mathematical model of whole-process calculation for bottom-blowing copper smelting

Science.gov (United States)

Li, Ming-zhou; Zhou, Jie-min; Tong, Chang-ren; Zhang, Wen-hai; Li, He-song

2017-11-01

The distribution law of materials in smelting products is key to cost accounting and contaminant control. Regardless, the distribution law is difficult to determine quickly and accurately by mere sampling and analysis. Mathematical models for material and heat balance in bottom-blowing smelting, converting, anode furnace refining, and electrolytic refining were established based on the principles of material (element) conservation, energy conservation, and control index constraint in copper bottom-blowing smelting. Simulation of the entire process of bottom-blowing copper smelting was established using a self-developed MetCal software platform. A whole-process simulation for an enterprise in China was then conducted. Results indicated that the quantity and composition information of unknown materials, as well as heat balance information, can be quickly calculated using the model. Comparison of production data revealed that the model can basically reflect the distribution law of the materials in bottom-blowing copper smelting. This finding provides theoretical guidance for mastering the performance of the entire process.

Adsorption and desorption characteristics of crystal violet in bottom ash column

Directory of Open Access Journals (Sweden)

Puthiya Veetil Nidheesh

2012-06-01

Full Text Available This study described adsorption of Crystal Violet (CV by bottom ash in fixed-bed column mode. Equilibrium of adsorption was studied in batch mode for finding adsorption capacity of bottom ash. In fixed bed column adsorption, the effects of bed height, feed flow rate, and initial concentration were studied by assessing breakthrough curve. The slope of the breakthrough curve decreased with increasing bed height. The breakthrough time and exhaustion time were decreased with increasing influent CV concentration and flow rates. The effect of bed depth, flow rate and CV concentration on the adsorption column design parameters were analyzed. Bed depth service time (BDST model was applied for analysis of crystal violet adsorption in the column. The adsorption capacity of bottom ash was calculated at 10% breakthrough point for different flow rates and concentrations. Desorption studies reveals that recovery of CV from bottom ash was effective by using CH3COOH than H2SO4, NaOH, HCl and NaCl solutions.

ADSORPTION AND DESORPTION CHARACTERISTICS OF CRYSTAL VIOLET IN BOTTOM ASH COLUMN

Directory of Open Access Journals (Sweden)

Puthiya Veetil Nidheesh

2012-01-01

Full Text Available This study described adsorption of Crystal Violet (CV by bottom ash in fixed-bed column mode. Equilibrium of adsorption was studied in batch mode for finding adsorption capacity of bottom ash. In fixed bed column adsorption, the effects of bed height, feed flow rate, and initial concentration were studied by assessing breakthrough curve. The slope of the breakthrough curve decreased with increasing bed height. The breakthrough time and exhaustion time were decreased with increasing influent CV concentration and flow rates. The effect of bed depth, flow rate and CV concentration on the adsorption column design parameters were analyzed. Bed depth service time (BDST model was applied for analysis of crystal violet adsorption in the column. The adsorption capacity of bottom ash was calculated at 10% breakthrough point for different flow rates and concentrations. Desorption studies reveals that recovery of CV from bottom ash was effective by using CH3COOH than H2SO4, NaOH, HCl and NaCl solutions.

Processed bottom ash for replacing fine aggregate in making high-volume fly ash concrete

OpenAIRE

Antoni; Sulistio Aldi Vincent; Wahjudi Samuel; Hardjito Djwantoro; Hardjito Djwantoro

2017-01-01

Bottom ash is a coal plant by-product that is abundant and underutilized. There is the potential use of bottom ash as a fine aggregate replacement in concrete mixtures; however, the problems of water absorption and uniformity of quality of the material need to be overcome first. In this study, bottom ash was treated by sieve separation and pounding to smaller particle size for use as a sand substitute. The physical and chemical characteristics of bottom ash were tested after treatment includi...

Measuring Sandy Bottom Dynamics by Exploiting Depth from Stereo Video Sequences

DEFF Research Database (Denmark)

Musumeci, Rosaria E.; Farinella, Giovanni M.; Foti, Enrico

2013-01-01

In this paper an imaging system for measuring sandy bottom dynamics is proposed. The system exploits stereo sequences and projected laser beams to build the 3D shape of the sandy bottom during time. The reconstruction is used by experts of the field to perform accurate measurements and analysis...

Bottom-up synthetic biology: modular design for making artificial platelets

Science.gov (United States)

Majumder, Sagardip; Liu, Allen P.

2018-01-01

Engineering artificial cells to mimic one or multiple fundamental cell biological functions is an emerging area of synthetic biology. Reconstituting functional modules from biological components in vitro is a challenging yet an important essence of bottom-up synthetic biology. Here we describe the concept of building artificial platelets using bottom-up synthetic biology and the four functional modules that together could enable such an ambitious effort.

Bottom depth and type for shallow waters: Hyperspectral observations from a blimp

Energy Technology Data Exchange (ETDEWEB)

Lee, ZhongPing; Carder, K.; Steward, R. [Univ. of South Florida, St. Petersburg, FL (United States)] [and others

1997-08-01

In a study of a blimp transect over Tampa Bay (Florida), hyperspectral upwelling radiance over the sand and seagrass bottoms was measured. These measurements were converted to hyperspectral remote-sensing reflectances. Using a shallow-water remote-sensing-reflectance model, in-water optical properties, bottom depths and bottom albedos were derived analytically and simultaneously by an optimization procedure. In the process, curvatures of sand and seagrass albedos were used. Also used was a model of absorption spectrum of phytoplankton pigments. The derived bottom depths were compared with bathymetry charts and found to agree well. This study suggests that a low-flying blimp is a useful platform for the study and mapping of coastal water environments. The optical model as well as the data-reduction procedure used are practical for the retrieval of shallow water optical properties.

Measuring device for water quality at reactor bottom

Energy Technology Data Exchange (ETDEWEB)

Urata, Hidehiro; Takagi, Jun-ichi

1995-10-27

The present invention concerns measurement for water quality at the bottom of a reactor of a BWR type plant, in which reactor water is sampled and analyzed in a state approximate to conditions in a pressure vessel. Based on the result, hydrogen injection amount is controlled during hydrogen injection operation. Namely, a monitor for water quality is disposed to a sampling line in communication with the bottom of a pressure vessel. A water quality monitor is disposed to a drain sampling line in communication with the bottom of the pressure vessel. A corrosion potentiometer is disposed to the pressure sampling line or the drain sampling line. A dissolved oxygen measuring device is disposed to the pressure vessel sampling line or the drain sampling line. With such a constitution, the reactor water can be sampled and analyzed in a state approximate to the conditions in the pressure vessel. In addition, signals from the water quality monitor are inputted to a hydrogen injection amount control device. As a result, the amount of hydrogen injected to primary coolants can be controlled in a state approximate to the conditions in the pressure vessel. (I.S.).

Measuring device for water quality at reactor bottom

International Nuclear Information System (INIS)

Urata, Hidehiro; Takagi, Jun-ichi.

1995-01-01

The present invention concerns measurement for water quality at the bottom of a reactor of a BWR type plant, in which reactor water is sampled and analyzed in a state approximate to conditions in a pressure vessel. Based on the result, hydrogen injection amount is controlled during hydrogen injection operation. Namely, a monitor for water quality is disposed to a sampling line in communication with the bottom of a pressure vessel. A water quality monitor is disposed to a drain sampling line in communication with the bottom of the pressure vessel. A corrosion potentiometer is disposed to the pressure sampling line or the drain sampling line. A dissolved oxygen measuring device is disposed to the pressure vessel sampling line or the drain sampling line. With such a constitution, the reactor water can be sampled and analyzed in a state approximate to the conditions in the pressure vessel. In addition, signals from the water quality monitor are inputted to a hydrogen injection amount control device. As a result, the amount of hydrogen injected to primary coolants can be controlled in a state approximate to the conditions in the pressure vessel. (I.S.)

Current Enhancement with Contact-Area-Limited Doping for Bottom-Gate, Bottom-Contact Organic Thin-Film Transistors

Science.gov (United States)

Noda, Kei; Wakatsuki, Yusuke; Yamagishi, Yuji; Wada, Yasuo; Toyabe, Toru; Matsushige, Kazumi

2013-02-01

The current enhancement mechanism in contact-area-limited doping for bottom-gate, bottom-contact (BGBC) p-channel organic thin-film transistors (OTFTs) was investigated both by simulation and experiment. Simulation results suggest that carrier shortage and large potential drop occur in the source-electrode/channel interface region in a conventional BGBC OTFT during operation, which results in a decrease in the effective field-effect mobility. These phenomena are attributed to the low carrier concentration of active semiconductor layers in OTFTs and can be alleviated by contact-area-limited doping, where highly doped layers are prepared over source-drain electrodes. According to two-dimensional current distribution obtained from the device simulation, a current flow from the source electrode to the channel region via highly doped layers is generated in addition to the direct carrier injection from the source electrode to the channel, leading to the enhancement of the drain current and effective field-effect mobility. The expected current enhancement mechanism in contact-area-limited doping was experimentally confirmed in typical α-sexithiophene (α-6T) BGBC thin-film transistors.

Bottom Production

CERN Document Server

Nason, P.; Schneider, O.; Tartarelli, G.F.; Vikas, P.; Baines, J.; Baranov, S.P.; Bartalini, P.; Bay, A.; Bouhova, E.; Cacciari, M.; Caner, A.; Coadou, Y.; Corti, G.; Damet, J.; Dell'Orso, R.; De Mello Neto, J.R.T.; Domenech, J.L.; Drollinger, V.; Eerola, P.; Ellis, N.; Epp, B.; Frixione, S.; Gadomski, S.; Gavrilenko, I.; Gennai, S.; George, S.; Ghete, V.M.; Guy, L.; Hasegawa, Y.; Iengo, P.; Jacholkowska, A.; Jones, R.; Kharchilava, A.; Kneringer, E.; Koppenburg, P.; Korsmo, H.; Kramer, M.; Labanca, N.; Lehto, M.; Maltoni, F.; Mangano, Michelangelo L.; Mele, S.; Nairz, A.M.; Nakada, T.; Nikitin, N.; Nisati, A.; Norrbin, E.; Palla, F.; Rizatdinova, F.; Robins, S.; Rousseau, D.; Sanchis-Lozano, M.A.; Shapiro, M.; Sherwood, P.; Smirnova, L.; Smizanska, M.; Starodumov, A.; Stepanov, N.; Vogt, R.

2000-01-01

We review the prospects for bottom production physics at the LHC. Members of the working group who has contributed to this document are: J. Baines, S.P. Baranov, P. Bartalini, A. Bay, E. Bouhova, M. Cacciari, A. Caner, Y. Coadou, G. Corti, J. Damet, R. Dell'Orso, J.R.T. De Mello Neto, J.L. Domenech, V. Drollinger, P. Eerola, N. Ellis, B. Epp, S. Frixione, S. Gadomski, I. Gavrilenko, S. Gennai, S. George, V.M. Ghete, L. Guy, Y. Hasegawa, P. Iengo, A. Jacholkowska, R. Jones, A. Kharchilava, E. Kneringer, P. Koppenburg, H. Korsmo, M. Kraemer, N. Labanca, M. Lehto, F. Maltoni, M.L. Mangano, S. Mele, A.M. Nairz, T. Nakada, N. Nikitin, A. Nisati, E. Norrbin, F. Palla, F. Rizatdinova, S. Robins, D. Rousseau, M.A. Sanchis-Lozano, M. Shapiro, P. Sherwood, L. Smirnova, M. Smizanska, A. Starodumov, N. Stepanov, R. Vogt

Methodological peculiarities of the Braun-Blanquet method used for marine bottom vegetation classification

Directory of Open Access Journals (Sweden)

AFANASYEV Dmitry F.

2012-09-01

Full Text Available The features of the Brown Blanquet method application for the classification of the Black and Azov Seas bottom phytocenoses are discussed. Special attention is given to following methodological questions: term of observations, necessary for associations revealing, size of relevance area, the features of geobotanic al underwater exploration technology, description of the bottom communities with epiphytes and the peculiarities of bottom vegetation syntaxonomic analysis.

Bottom-up and top-down emotion generation: implications for emotion regulation

Science.gov (United States)

Misra, Supriya; Prasad, Aditya K.; Pereira, Sean C.; Gross, James J.

2012-01-01

Emotion regulation plays a crucial role in adaptive functioning and mounting evidence suggests that some emotion regulation strategies are often more effective than others. However, little attention has been paid to the different ways emotions can be generated: from the ‘bottom-up’ (in response to inherently emotional perceptual properties of the stimulus) or ‘top-down’ (in response to cognitive evaluations). Based on a process priming principle, we hypothesized that mode of emotion generation would interact with subsequent emotion regulation. Specifically, we predicted that top-down emotions would be more successfully regulated by a top-down regulation strategy than bottom-up emotions. To test this hypothesis, we induced bottom-up and top-down emotions, and asked participants to decrease the negative impact of these emotions using cognitive reappraisal. We observed the predicted interaction between generation and regulation in two measures of emotional responding. As measured by self-reported affect, cognitive reappraisal was more successful on top-down generated emotions than bottom-up generated emotions. Neurally, reappraisal of bottom-up generated emotions resulted in a paradoxical increase of amygdala activity. This interaction between mode of emotion generation and subsequent regulation should be taken into account when comparing of the efficacy of different types of emotion regulation, as well as when reappraisal is used to treat different types of clinical disorders. PMID:21296865

Intelligent Evaluation Method of Tank Bottom Corrosion Status Based on Improved BP Artificial Neural Network

Science.gov (United States)

Qiu, Feng; Dai, Guang; Zhang, Ying

According to the acoustic emission information and the appearance inspection information of tank bottom online testing, the external factors associated with tank bottom corrosion status are confirmed. Applying artificial neural network intelligent evaluation method, three tank bottom corrosion status evaluation models based on appearance inspection information, acoustic emission information, and online testing information are established. Comparing with the result of acoustic emission online testing through the evaluation of test sample, the accuracy of the evaluation model based on online testing information is 94 %. The evaluation model can evaluate tank bottom corrosion accurately and realize acoustic emission online testing intelligent evaluation of tank bottom.

MAPPING OF THE RUSSIAN NORTHERN SEAS BOTTOM RELIEF USING DIGITAL ELEVATION MODELS

Directory of Open Access Journals (Sweden)

S. M. Koshel

2014-01-01

Full Text Available The task of the project is the design of the digital elevation models (DEM of the bottoms of Barents Sea, Pechora Sea, and the White Sea. Accuracy (resolution of DEMs allows for adequate delineation of morphological structures and peculiarities of the sea bottoms and the design of bathymetrical and derivative maps. DEMs of the sea bottom were compiled using data from navigation charts of different scales, where additional isobaths were drawn manually taking into account the classification features of the bottom topography forms. Next procedures were carried out: scanning of these charts, processing of scanned images, isobaths vectorization and creation of attribute tables, vector layers transformation to geographical coordinates as well editing, merging and joining of the map sheets, correction of geometry and attributes. For generation of digital model of bottom topography it is important to choose algorithm which allows for representation all of the sea bottom features expressed by isobaths in most details. The original algorithm based on fast calculation of distances to the two different nearest isobaths was used. Interpretation of isolines as vector linear objects is the main peculiarity of this algorithm. The resulted DEMs were used to design bathymetrical maps of Barents Sea of 1:2 500 000 scale, Pechora Sea of 1:1 000 000 scale, and White Sea of 1:750 000 scale. Different derivative maps were compiled based on DEM of the White Sea.

Z decay into a bottom quark, a light sbottom, and a light gluino

International Nuclear Information System (INIS)

Cheung Kingman; Keung Waiyee

2003-01-01

The discrepancy between the measured and theoretical production cross section of b quarks at the Fermilab Tevatron can probably be explained by the recently proposed scenario of light gluinos of mass 12-16 GeV and light sbottoms of mass 2-5.5 GeV. In this scenario, we study a related process at the Z pole, Z→bb-tilde 1 * g-tilde+b-barb-tilde 1 g-tilde followed by g-tilde→bb-tilde 1 */b-barb-tilde 1 . The hadronic branching ratio for this channel is (1-3)x10 -3 , which is of the order of the size of the uncertainty in R b . We find that a typical event consists of an energetic prompt bottom jet back to back with a 'fat' bottom jet, which consists of a bottom quark and two bottom squarks. Such events with a 10 -3 branching ratio may affect the measurement of R b ; they are even more interesting if the fat bottom jet can be identified

Development of built-in debris-filter bottom nozzle for PWR fuel assemblies

International Nuclear Information System (INIS)

Juntaro Shimizu; Kazuki Monaka; Masaji Mori; Kazuo Ikeda

2005-01-01

Mitsubishi Heavy Industries, Ltd. (MHI) has worked to improve the capability of anti debris bottom nozzle for a PWR fuel assembly. The Current debris filter bottom nozzle (DFBN) having 4mm diameter flow holes can capture the larger size of debris than the flow hole inner diameter. MHI has completed the development of the built-in debris filter bottom nozzle, which is the new idea of the debris-filter for high burnup (55GWd/t assembly average burnup). Built-in debris filter bottom nozzle consists of the blades and nozzle body. The blades made from inconel strip are embedded and welded on the grooved top surface of the bottom nozzle adapter plate. A flow hole is divided by the blade and the trap size of the debris is reduced. Because the blades block the coolant flow, it was anticipated to increase the pressure loss of the nozzle, however, adjusting the relation between blade and taper shape of the flow hole, the pressure loss has been successfully maintained the satisfactory level. Grooves are cut on the nozzle plate; nevertheless, the additional skirts on the four sides of the nozzle compensate the structural strength. (authors)

Utilization of power plant bottom-ash particles as stabilizer in aluminum foams

Energy Technology Data Exchange (ETDEWEB)

Asavavisithchai, Seksak; Prapajaraswong, Attanadol [Chulalongkorn Univ., Bangkok (Thailand). Dept. of Metallurgical Engineering

2013-07-01

Aluminum foams, produced via powder metallurgical (PM) process, normally require the addition of ceramic particles in compaction stage, in order to increase both foamability of precursors and mechanical properties of the final foam products. Bottom ash particles are a by-product waste obtained from thermoelectric power plants which are commonly found to be used in landfill facilities. The major chemical constituent, approximately between 30 wt.-% and 60 wt.-%, of bottom ash particles is SiO{sub 2}, depending on chemical composition in coal, sintering condition and environment, and other process parameters. In this study, we explore the feasibility of utilizing bottom ash particles of thermoelectric power plant wastes as stabilizer in aluminum foams. A small amount of two-size bottom ash particles (mean size of 78 {mu}m and 186 {mu}m), between 1 wt.-% and 5 wt.-%, have been added to aluminum foams. Foam expansion, macro- and microstructures as well as mechanical properties, such as compressive strength and microhardness, were investigated. The results from the present study suggest that bottom ash particles can be used as a stabilizing material which can improve both cellular structure and mechanical properties of aluminum foams. (orig.)

Testing the possibility for reusing mswi bottom ash in Greenlandic road construction

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Jørgensen, Anders Stuhr; Villumsen, Arne

2012-01-01

requirements (a grain size distribution, wear resistance, visual fraction analysis and bearing capacity) for reuse as fill material in road construction [2]. Environmental classification based on heavy metal content and leachability was also investigated. The tests showed that it will not be possible to use......, which can influence the quality of MWSI residues. About 15,000 tons MSWI bottom ash is produced annually in Greenland and is disposed of at the open disposal sites without leachate collection or encapsulation. The MSWI bottom ash could have value as a secondary resource in construction work in Greenland...... the bottom ash directly after the incineration as the bottom ash did not comply with all the requirements specified by the Danish Road Directorate. These technical requirements could be improved by removing large fractions (> 45mm) and metal parts as well as changing the grain size distribution...

Double-double effect and coordination number

International Nuclear Information System (INIS)

Mioduski, T.

1992-01-01

The original method of interpretation together with its theoretical foundations is developed, making it possible to use location and direction of the double-double (tetrad) effect within the Ln and An series to determine the coordination number (CN) complexes of the f-block elements. The method is applied for potentiometric and radiometric equilibrium studies. It has been pointed and that the decisive factor for the direction of the double-double effect in the case of the Gibbs energy variations is a difference in the CN of the f-element ion between the reaction product complex and that for the reaction substrate the ''regular'' effect for a given tetrad is accompanied by decrease in the CN while the ''reverse'' effect by increase in the CN. (author). 122 refs, 5 tabs, 8 figs

An experimental study on sodium-water reaction in the double pool LMFBR, (4)

International Nuclear Information System (INIS)

Kumagai, Hiromichi; Yoshida, Kazuo; Uotani, Masaki; Akimoto, Tokuzo

1989-01-01

Double Pool type LMFBR set the rectangular cross-sectional steam generator (SGs) inside a secondary vessel. The initial spike pressure rise caused by large sodium-water reaction in SGs might be radiated into a large sodium pool in the secondary vessel. Therefore basic experiments on pressure wave propagation were carried out by generating pressure wave in water by mean of a set of drop hummer and piston. But the experimental apparatus in water was not convenience to simulate the structure near the bottom end of the SGs shell. In this reports, experiments were carried out by generating pulse sound pressure in air, and compared with the results pressure waves in water. (author)

Bottom production

Energy Technology Data Exchange (ETDEWEB)

Baines, J.; Baranov, S.P.; Bartalini, P.; Bay, A.; Bouhova, E.; Cacciari, M.; Caner, A.; Coadou, Y.; Corti, G.; Damet, J.; Dell-Orso, R.; De Mello Neto, J.R.T.; Domenech, J.L.; Drollinger, V.; Eerola, P.; Ellis, N.; Epp, B.; Frixione, S.; Gadomski, S.; Gavrilenko, I.; Gennai, S.; George, S.; Ghete, V.M.; Guy, L.; Hasegawa, Y.; Iengo, P.; Jacholkowska, A.; Jones, R.; Kharchilava, A.; Kneringer, E.; Koppenburg, P.; Korsmo, H.; Kramer, M.; Labanca, N.; Lehto, M.; Maltoni, F.; Mangano, M.L.; Mele, S.; Nairz, A.M.; Nakada, T.; Nikitin, N.; Nisati, A.; Norrbin, E.; Palla, F.; Rizatdinova, F.; Robins, S.; Rousseau, D.; Sanchis-Lozano, M.A.; Shapiro, M.; Sherwood, P.; Smirnova, L.; Smizanska, M.; Starodumov, A.; Stepanov, N.; Vogt, R.

2000-03-15

In the context of the LHC experiments, the physics of bottom flavoured hadrons enters in different contexts. It can be used for QCD tests, it affects the possibilities of B decays studies, and it is an important source of background for several processes of interest. The physics of b production at hadron colliders has a rather long story, dating back to its first observation in the UA1 experiment. Subsequently, b production has been studied at the Tevatron. Besides the transverse momentum spectrum of a single b, it has also become possible, in recent time, to study correlations in the production characteristics of the b and the b. At the LHC new opportunities will be offered by the high statistics and the high energy reach. One expects to be able to study the transverse momentum spectrum at higher transverse momenta, and also to exploit the large statistics to perform more accurate studies of correlations.

Bottom production

International Nuclear Information System (INIS)

Baines, J.; Baranov, S.P.; Bartalini, P.; Bay, A.; Bouhova, E.; Cacciari, M.; Caner, A.; Coadou, Y.; Corti, G.; Damet, J.; Dell-Orso, R.; De Mello Neto, J.R.T.; Domenech, J.L.; Drollinger, V.; Eerola, P.; Ellis, N.; Epp, B.; Frixione, S.; Gadomski, S.; Gavrilenko, I.; Gennai, S.; George, S.; Ghete, V.M.; Guy, L.; Hasegawa, Y.; Iengo, P.; Jacholkowska, A.; Jones, R.; Kharchilava, A.; Kneringer, E.; Koppenburg, P.; Korsmo, H.; Kramer, M.; Labanca, N.; Lehto, M.; Maltoni, F.; Mangano, M.L.; Mele, S.; Nairz, A.M.; Nakada, T.; Nikitin, N.; Nisati, A.; Norrbin, E.; Palla, F.; Rizatdinova, F.; Robins, S.; Rousseau, D.; Sanchis-Lozano, M.A.; Shapiro, M.; Sherwood, P.; Smirnova, L.; Smizanska, M.; Starodumov, A.; Stepanov, N.; Vogt, R.

2000-01-01

In the context of the LHC experiments, the physics of bottom flavoured hadrons enters in different contexts. It can be used for QCD tests, it affects the possibilities of B decays studies, and it is an important source of background for several processes of interest. The physics of b production at hadron colliders has a rather long story, dating back to its first observation in the UA1 experiment. Subsequently, b production has been studied at the Tevatron. Besides the transverse momentum spectrum of a single b, it has also become possible, in recent time, to study correlations in the production characteristics of the b and the b. At the LHC new opportunities will be offered by the high statistics and the high energy reach. One expects to be able to study the transverse momentum spectrum at higher transverse momenta, and also to exploit the large statistics to perform more accurate studies of correlations

Double Charge Exchange Reactions and Double Beta Decay

Science.gov (United States)

Auerbach, N.

2018-05-01

The subject of this presentation is at the forefront of nuclear physics, namely double beta decay. In particular one is most interested in the neutrinoless process of double beta decay, when the decay proceeds without the emission of two neutrinos. The observation of such decay would mean that the lepton conservation symmetry is violated and that the neutrinos are of Majorana type, meaning that they are their own anti-particles. The life time of this process has two unknowns, the mass of the neutrino and the nuclear matrix element. Determining the nuclear matrix element and knowing the cross-section well will set limits on the neutrino mass. There is a concentrated effort among the nuclear physics community to calculate this matrix element. Usually these matrix elements are a very small part of the total strength of the transition operators involved in the process. There is no simple way to “calibrate” the nuclear double beta decay matrix element. The double beta decay is a double charge exchange process, therefore it is proposed that double charge exchange reactions using ion projectiles on nuclei that are candidates for double beta decay, will provide additional necessary information about the nuclear matrix elements.

Coil in bottom part of splitter magnet

CERN Multimedia

CERN PhotoLab

1976-01-01

Radiation-resistant coil being bedded into the bottom part of a splitter magnet. This very particular magnet split the beam into 3 branches, for 3 target stations in the West-Area. See Annual Report 1975, p.176, Figs.14 and 15.

The Role of Rough Topography in Mediating Impacts of Bottom Drag in Eddying Ocean Circulation Models.

Science.gov (United States)

Trossman, David S; Arbic, Brian K; Straub, David N; Richman, James G; Chassignet, Eric P; Wallcraft, Alan J; Xu, Xiaobiao

2017-08-01

Motivated by the substantial sensitivity of eddies in two-layer quasi-geostrophic (QG) turbulence models to the strength of bottom drag, this study explores the sensitivity of eddies in more realistic ocean general circulation model (OGCM) simulations to bottom drag strength. The OGCM results are interpreted using previous results from horizontally homogeneous, two-layer, flat-bottom, f-plane, doubly periodic QG turbulence simulations and new results from two-layer β -plane QG turbulence simulations run in a basin geometry with both flat and rough bottoms. Baroclinicity in all of the simulations varies greatly with drag strength, with weak drag corresponding to more barotropic flow and strong drag corresponding to more baroclinic flow. The sensitivity of the baroclinicity in the QG basin simulations to bottom drag is considerably reduced, however, when rough topography is used in lieu of a flat bottom. Rough topography reduces the sensitivity of the eddy kinetic energy amplitude and horizontal length scales in the QG basin simulations to bottom drag to an even greater degree. The OGCM simulation behavior is qualitatively similar to that in the QG rough bottom basin simulations in that baroclinicity is more sensitive to bottom drag strength than are eddy amplitudes or horizontal length scales. Rough topography therefore appears to mediate the sensitivity of eddies in models to the strength of bottom drag. The sensitivity of eddies to parameterized topographic internal lee wave drag, which has recently been introduced into some OGCMs, is also briefly discussed. Wave drag acts like a strong bottom drag in that it increases the baroclinicity of the flow, without strongly affecting eddy horizontal length scales.

76 FR 19125 - Bottom Mount Combination Refrigerator-Freezers From Korea and Mexico

Science.gov (United States)

2011-04-06

...)] Bottom Mount Combination Refrigerator-Freezers From Korea and Mexico AGENCY: United States International... bottom mount combination refrigerator-freezers from Korea and Mexico, provided for in subheadings 8418.10... five business days thereafter, or by May 23, 2011. For further information concerning the conduct of...

Bottom-pressure observations of deep-sea internal hydrostatic and non-hydrostatic motions

NARCIS (Netherlands)

van Haren, H.

2013-01-01

In the ocean, sloping bottom topography is important for the generation and dissipation of internal waves. Here, the transition of such waves to turbulence is demonstrated using an accurate bottom-pressure sensor that was moored with an acoustic Doppler current profiler and high-resolution

Fresh Properties and Flexural Strength of Self-Compacting Concrete Integrating Coal Bottom Ash

Directory of Open Access Journals (Sweden)

Jamaluddin Norwati

2016-01-01

Full Text Available This paper presents the effect of using coal bottom ash as a partial replacement of fine aggregates in self-compacting concrete (SCC on its fresh properties and flexural strength. A comparison between SCC with various replacements of fine aggregates with coal bottom ash showed that SCC obtained flexural strength decrease on increase of water cement ratio from 0.35 to 0.45. The natural sand was replaced with coal bottom ash up to 30% volumetrically. The fresh properties were investigated by slump flow, T500 spread time, L-box test and sieve segregation resistance in order to evaluate its self-compatibility by compared to control samples embed with natural sand. The results revealed that the flowability and passing ability of SCC mixtures are decreased with higher content of coal bottom ash replacement. The results also showed that the flexural strength is affected by the presence of coal bottom ash in the concrete. In addition, the water cement ratios are influence significantly with higher binder content in concrete.

Large Eddy Simulations of a Bottom Boundary Layer Under a Shallow Geostrophic Front

Science.gov (United States)

Bateman, S. P.; Simeonov, J.; Calantoni, J.

2017-12-01

The unstratified surf zone and the stratified shelf waters are often separated by dynamic fronts that can strongly impact the character of the Ekman bottom boundary layer. Here, we use large eddy simulations to study the turbulent bottom boundary layer associated with a geostrophic current on a stratified shelf of uniform depth. The simulations are initialized with a spatially uniform vertical shear that is in geostrophic balance with a pressure gradient due to a linear horizontal temperature variation. Superposed on the temperature front is a stable vertical temperature gradient. As turbulence develops near the bottom, the turbulence-induced mixing gradually erodes the initial uniform temperature stratification and a well-mixed layer grows in height until the turbulence becomes fully developed. The simulations provide the spatial distribution of the turbulent dissipation and the Reynolds stresses in the fully developed boundary layer. We vary the initial linear stratification and investigate its effect on the height of the bottom boundary layer and the turbulence statistics. The results are compared to previous models and simulations of stratified bottom Ekman layers.

90Sr content in the Black Sea bottom sediments after the Chernobyl NPP accident and its use as a radiotracer for an assessment of bottom settlement rate

International Nuclear Information System (INIS)

Mirzoyeva, N. Y.; Egorov, V. N.; Polikarpov, G. G.

2006-01-01

The increase of 9 0Sr concentrations in the Black Sea bottom sediments along to western coast of the Black Sea and south part of Crimea was observed in 1987-1988 years. To our opinion, it was connected with hydrological processes (for example, currents), occurring in the given sea parts. The most polluted by post-Chernobyl 9 0Sr areas were bottom sediments of Dnieper, Dniester and Danube River deltas, territory of an arrangement of a main channel of the North-Crimea Channel - region of a peninsula Tarkhankut, southeast part of Crimea (Feodosiya area). The similar situation in confined of the greatest contents 9 0Sr to the specified areas not only is kept with time (till 2000), but the process of increase of 9 0Sr concentration in bottom sediments of the investigated regions is observed. So average concentration of 9 0Sr in Dnieper River delta bottom sediments in 1987 was 28,5 Bq kg - 1 , in 2000 - 148,2 28,5 Bq kg - 1 of Dry Weight. Such character of 9 0Sr redistribution shows, that both in first years after Chernobyl NPP accident, and in the following time, the entry of 9 0Sr in the Black Sea basin occurs, basically, with water flow of the large rivers in a northwest part of the Black Sea, discharge waters of the North-Crimean Channel. These sources of 9 0Sr input to the Black Sea ecosystem considerably prevailed above direct atmospheric pollution by given radionuclide in April-May 1986 at once after the Chernobyl NPP accident. On the base of monitoring researches results the maps of 9 0Sr dynamics redistribution in the Black Sea bottom sediments (0-5 cm) since 1986 (Chernobyl NPP accident) up to 2000 were sketched out. The distribution of 9 0Sr radionuclide in the bottom sediments columns, which were selected from the Corukh river mouth region and from the Dnieper-Bug estuary area, is investigated. The peaks of 9 0Sr increased contents were founded in the profile of its vertical distribution in the bottom sediments. These peaks correspond to the periods of 9 0Sr

Cathodic protection simulation of above ground storage tank bottom: Experimental and numerical results

Energy Technology Data Exchange (ETDEWEB)

Schultz, Marcelo [Inspection Department, Rio de Janeiro Refinery - REDUC, Petrobras, Rio de Janeiro (Brazil); Brasil, Simone L.D.C. [Chemistry School, Federal University of Rio de Janeiro, UFRJ, Rio de Janeiro (Brazil); Baptista, Walmar [Corrosion Department, Research Centre - CENPES, Petrobras (Brazil); Miranda, Luiz de [Materials and Metallurgical Engineering Program, COPPE, UFRJ, Rio de Janeiro (Brazil); Brito, Rosane F. [Corrosion Department, Research Centre, CENPES, Petrobras, Rio de Janeiro (Brazil)

2004-07-01

The deterioration history of Above ground Storage Tanks (AST) of Petrobras' refineries - shows that the great incidence of corrosion in the AST bottom is at the external side. This is a problem in the disposability of storage crude oil and other final products. At this refinery, all AST's are built over a concrete base with a lot of pile to support the structure and distribute the charge homogeneously. Because of this it is very difficult to use cathodic protection as an anti-corrosive method for each one of these tanks. This work presents an alternative cathodic protection system to protect the external side of the tank bottom using a new metallic bottom, placed at different distance from the original one. The space between the two bottoms was filled with one of two kinds of soils, sand or clay, more conductive than the concrete. Using a prototype tank it was studied the potential distributions over the new tank bottom for different system parameters, as soil resistivity, number and position of anodes localized in the old bottom. These experimental results were compared to numerical simulations, carried out using a software based on the Boundary Element Method. The computer simulation validates this protection method, confirming to be a very useful tool to define the optimized cathodic protection system configuration. (authors)

Bottom-up vs. top-down effects on terrestrial insect herbivores: a meta-analysis.

Science.gov (United States)

Vidal, Mayra C; Murphy, Shannon M

2018-01-01

Primary consumers are under strong selection from resource ('bottom-up') and consumer ('top-down') controls, but the relative importance of these selective forces is unknown. We performed a meta-analysis to compare the strength of top-down and bottom-up forces on consumer fitness, considering multiple predictors that can modulate these effects: diet breadth, feeding guild, habitat/environment, type of bottom-up effects, type of top-down effects and how consumer fitness effects are measured. We focused our analyses on the most diverse group of primary consumers, herbivorous insects, and found that in general top-down forces were stronger than bottom-up forces. Notably, chewing, sucking and gall-making herbivores were more affected by top-down than bottom-up forces, top-down forces were stronger than bottom-up in both natural and controlled (cultivated) environments, and parasitoids and predators had equally strong top-down effects on insect herbivores. Future studies should broaden the scope of focal consumers, particularly in understudied terrestrial systems, guilds, taxonomic groups and top-down controls (e.g. pathogens), and test for more complex indirect community interactions. Our results demonstrate the surprising strength of forces exerted by natural enemies on herbivorous insects, and thus the necessity of using a tri-trophic approach when studying insect-plant interactions. © 2017 John Wiley & Sons Ltd/CNRS.

Diagnostic study, design and implementation of an integrated model of care in France: a bottom-up process with continuous leadership

Directory of Open Access Journals (Sweden)

Matthieu de Stampa

2010-02-01

Full Text Available Background: Sustaining integrated care is difficult, in large part because of problems encountered securing the participation of health care and social service professionals and, in particular, general practitioners (GPs. Purpose: To present an innovative bottom-up and pragmatic strategy used to implement a new integrated care model in France for community-dwelling elderly people with complex needs. Results: In the first step, a diagnostic study was conducted with face-to-face interviews to gather data on current practices from a sample of health and social stakeholders working with elderly people. In the second step, an integrated care model called Coordination Personnes Agées (COPA was designed by the same major stakeholders in order to define its detailed characteristics based on the local context. In the third step, the model was implemented in two phases: adoption and maintenance. This strategy was carried out by a continuous and flexible leadership throughout the process, initially with a mixed leadership (clinician and researcher followed by a double one (clinician and managers of services in the implementation phase. Conclusion: The implementation of this bottom-up and pragmatic strategy relied on establishing a collaborative dynamic among health and social stakeholders. This enhanced their involvement throughout the implementation phase, particularly among the GPs, and allowed them to support the change practices and services arrangements

Stabilization of bottom sediments from Rzeszowski Reservoir

Directory of Open Access Journals (Sweden)

Koś Karolina

2015-06-01

Full Text Available The paper presents results of stabilization of bottom sediments from Rzeszowski Reservoir. Based on the geotechnical characteristics of the tested sediments it was stated they do not fulfill all the criteria set for soils in earth embankments. Therefore, an attempt to improve their parameters was made by using two additives – cement and lime. An unconfined compressive strength, shear strength, bearing ratio and pH reaction were determined on samples after different time of curing. Based on the carried out tests it was stated that the obtained values of unconfined compressive strength of sediments stabilized with cement were relatively low and they did not fulfill the requirements set by the Polish standard, which concerns materials in road engineering. In case of lime stabilization it was stated that the tested sediments with 6% addition of the additive can be used for the bottom layers of the improved road base.

Importance of Nonperturbative QCD Parameters for Bottom Mesons

Directory of Open Access Journals (Sweden)

A. Upadhyay

2014-01-01

Full Text Available The importance of nonperturbative quantum chromodynamics (QCD parameters is discussed in context to the predicting power for bottom meson masses and isospin splitting. In the framework of heavy quark effective theory, the work presented here focuses on the different allowed values of the two nonperturbative QCD parameters used in heavy quark effective theory formula, and using the best fitted parameter, masses of the excited bottom meson states in jp=1/2+ doublet in strange and nonstrange sectors are calculated here. The calculated masses are found to be matching well with experiments and other phenomenological models. The mass splitting and hyperfine splitting have also been analyzed for both strange and nonstrange heavy mesons with respect to spin and flavor symmetries.

From Stable ZnO and GaN Clusters to Novel Double Bubbles and Frameworks

Directory of Open Access Journals (Sweden)

Matthew R. Farrow

2014-05-01

Full Text Available A bottom up approach is employed in the design of novel materials: first, gas-phase “double bubble” clusters are constructed from high symmetry, Th, 24 and 96 atom, single bubbles of ZnO and GaN. These are used to construct bulk frameworks. Upon geometry optimization—minimisation of energies and forces computed using density functional theory—the symmetry of the double bubble clusters is reduced to either C1 or C2, and the average bond lengths for the outer bubbles are 1.9 Å, whereas the average bonds for the inner bubble are larger for ZnO than for GaN; 2.0 Å and 1.9 Å, respectively. A careful analysis of the bond distributions reveals that the inter-bubble bonds are bi-modal, and that there is a greater distortion for ZnO. Similar bond distributions are found for the corresponding frameworks. The distortion of the ZnO double bubble is found to be related to the increased flexibility of the outer bubble when composed of ZnO rather than GaN, which is reflected in their bulk moduli. The energetics suggest that (ZnO12@(GaN48 is more stable both in gas phase and bulk frameworks than (ZnO12@(ZnO48 and (GaN12@(GaN48. Formation enthalpies are similar to those found for carbon fullerenes.

BWR fuel assembly bottom nozzle with one-way coolant flow valve

International Nuclear Information System (INIS)

Taleyarkhan, R.P.

1987-01-01

In a nuclear reactor having a flow of coolant/moderator fluid therein, at least one fuel assembly installed in the fluid flow, the fuel assembly is described comprising in combination: a bundle of elongated fuel rods disposed in side-by-side relationship so as to form an array of spaced fuel rods; an outer tubular flow channel surrounding the fuel rods so as to direct the flow of coolant/moderator fluid along the fuel rods; bottom and top nozzles mounted at opposite ends of the flow channel and having an inlet and outlet respectively for allowing entry and exit of the flow of coolant/moderator fluid into and from the flow channel and along the fuel rods therein; and a coolant flow direction control device operatively disposed in the bottom nozzle so as to open the inlet thereof to the flow of coolant/moderator fluid in an inflow direction into the flow channel through the bottom nozzle inlet but close the inlet to the flow of coolant/moderator fluid from the flow channel through the bottom nozzle inlet upon reversal of coolant/moderator fluid flow from the inflow direction

NMFS Bottom Longline Analytical Dataset Provided to NRDA

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The Southeast Fisheries Science Center Mississippi Laboratories has conducted standardized bottom longline surveys in the Gulf of Mexico and South Atlantic since...

s-Step Krylov Subspace Methods as Bottom Solvers for Geometric Multigrid

Energy Technology Data Exchange (ETDEWEB)

Williams, Samuel [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Lijewski, Mike [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Almgren, Ann [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Straalen, Brian Van [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Carson, Erin [Univ. of California, Berkeley, CA (United States); Knight, Nicholas [Univ. of California, Berkeley, CA (United States); Demmel, James [Univ. of California, Berkeley, CA (United States)

2014-08-14

Geometric multigrid solvers within adaptive mesh refinement (AMR) applications often reach a point where further coarsening of the grid becomes impractical as individual sub domain sizes approach unity. At this point the most common solution is to use a bottom solver, such as BiCGStab, to reduce the residual by a fixed factor at the coarsest level. Each iteration of BiCGStab requires multiple global reductions (MPI collectives). As the number of BiCGStab iterations required for convergence grows with problem size, and the time for each collective operation increases with machine scale, bottom solves in large-scale applications can constitute a significant fraction of the overall multigrid solve time. In this paper, we implement, evaluate, and optimize a communication-avoiding s-step formulation of BiCGStab (CABiCGStab for short) as a high-performance, distributed-memory bottom solver for geometric multigrid solvers. This is the first time s-step Krylov subspace methods have been leveraged to improve multigrid bottom solver performance. We use a synthetic benchmark for detailed analysis and integrate the best implementation into BoxLib in order to evaluate the benefit of a s-step Krylov subspace method on the multigrid solves found in the applications LMC and Nyx on up to 32,768 cores on the Cray XE6 at NERSC. Overall, we see bottom solver improvements of up to 4.2x on synthetic problems and up to 2.7x in real applications. This results in as much as a 1.5x improvement in solver performance in real applications.

Vertical single- and double-walled carbon nanotubes grown from modified porous anodic alumina templates

International Nuclear Information System (INIS)

Maschmann, Matthew R; Franklin, Aaron D; Amama, Placidus B; Zakharov, Dmitri N; Stach, Eric A; Sands, Timothy D; Fisher, Timothy S

2006-01-01

Vertical single-walled and double-walled carbon nanotube (SWNT and DWNT) arrays have been grown using a catalyst embedded within the pore walls of a porous anodic alumina (PAA) template. The initial film structure consisted of a SiO x adhesion layer, a Ti layer, a bottom Al layer, a Fe layer, and a top Al layer deposited on a Si wafer. The Al and Fe layers were subsequently anodized to create a vertically oriented pore structure through the film stack. CNTs were synthesized from the catalyst layer by plasma-enhanced chemical vapour deposition (PECVD). The resulting structure is expected to form the basis for development of vertically oriented CNT-based electronics and sensors

Phytotoxic effects of bottom sediments from Ignalina NPP wastewater canals and cooler

International Nuclear Information System (INIS)

Montvydiene, D.

2002-01-01

In the paper impact of Ignalina Nuclear Power Plant (INPP) waste upon phytotoxicity of sediments from Lake Drukshiai was recognized. Samples of bottom sediments were collected from various wastewater canals of INPP, from the canal of wastewater treatment plant (WWTP), small lake and rivulet, which are on the route of that wastes into Drukshiai. In 1995, 132 sites of Drukshiai were observed in order to assess the phytotoxicity of its bottom sediments. The research was carried out in July of 1993-2000. Number of somatic mutations (pink, colourless and morphological) and nonviable stamen hairs (the quantity of whose indicates lethality, when hair contains less than 12 cells) in Tradescantia (clone 02) stamen hair (SH) system was counted. Genotoxic effect of bottom sediments on Tradescantia was estimated according to Sparrow et al. (1972) and Marciulioniene et al. (1996). Genotoxic effects were considered weak if amount of somatic mutations not exceeded 1%, there were no non-viable stamen hairs, and medium effect was when the number of somatic mutations was between 1.0-4.0% and non-viable stamen hairs did not reach 40,0%. As well as strong effect was when numbers of somatic mutations and non-viable stamen hairs exceeding 4.0% and 40.0%, respectively. L. sativum is a rather sensitive, widely applied biotest because of its simplicity, cheapness and short duration. This test based on Magone (1989) method and lasted for 48 hours, after which time the seeds germination and root length of seedlings was measured. Tested bottom sediments causing percent inhibitions of 100-60%, 61-40%, 41-20%, and 20-0% were classified as highly toxic, moderately toxic, slightly toxic and non-toxic, respectively. Estimations in both cases were run in triplicates. The data were estimated using the analysis of variance with significance defined at α = 0,05. It was established that in accordance with the phytotoxic impact, the wastes discharged by INPP into Drukshiai in 1993-2000 are attributed

The influence of triple bottom line on international operations management

Directory of Open Access Journals (Sweden)

Francisco Sperotto Flores

2017-12-01

Full Text Available This paper takes a triple bottom line perspective to analyze how the international operations literature integrates economic, social, and environmental issues. Additionally, it shows the main drivers of and barriers to the adoption of triple bottom line practices by companies in an international context. We conducted a literature review in English language journals which publish research of production and operations management and sustainability, resulting in a final sample of 29 papers. Results show that social and legal pressure for companies to adopt a responsible behavior prompts an isomorphic process that leads them to conduct their operations on behalf of triple bottom line goals. Behavioral differences between spin-offs in various countries caused institutions to create mechanisms that can press and change private standards through regulation and enforcement. There is room for progress in studies that seek to analyze the company’s relationships in its international experience and its multi-institutional relations.

Carbon deposition at the bottom of gaps in TEXTOR experiments

International Nuclear Information System (INIS)

Matveev, D.; Kirschner, A.; Esser, H.G.; Freisinger, M.; Kreter, A.; Van Hoey, O.; Borodin, D.; Litnovsky, A.; Wienhold, P.; Coenen, J.W.; Stoschus, H.; Philipps, V.; Brezinsek, S.; Van Oost, G.

2013-01-01

Results of a new dedicated experiment addressing the problem of impurity deposition at the bottom in gaps are presented along with modelling. A test limiter with an isolated gap was exposed to the scrape-off layer plasma in TEXTOR. The exposure was accompanied by injection of 13 C-marked methane in the vicinity of the gap. Deposition at the bottom of the gap was monitored in situ with Quartz-Microbalance diagnostics. The 13 C deposition efficiency of about 2.6 × 10 −5 was measured. Post mortem analysis of resulting deposited layers performed with SIMS and EPMA techniques yields about a factor 2 smaller value corresponding to approximately 10% contribution of the gap bottom to the total 13 C deposition in the gap. This measured contribution is effectively much smaller than observed earlier in TEXTOR, taking the difference in geometry into account, and is in reasonable agreement with modelling performed with ERO and 3D-GAPS codes

Gear Selectivity of a Longfin Squid Bottom Trawl

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Loligo pealeii (longfin inshore squid) co-occurs with Atlantic butterfish (Peprilus triacanthus) throughout the year and discarding in the L. pealeii bottom trawl...

Analysis of hydrodynamic characteristics of unmanned underwater vehicle moving close to the sea bottom

Directory of Open Access Journals (Sweden)

Xiao-xu Du

2014-03-01

Full Text Available The accurate research on the hydrodynamics of unmanned underwater vehicle (UUV, which moves close to the sea bottom, has a great significance for its maneuverability. The structured grid of the computational models with different distances to the sea bottom and attack angles is generated by Ansys ICEM, and the flow field near the sea bottom is simulated using CFX. The characteristics of the drag, lift, pitching moment influenced by the distance to sea bottom and the attack angle are studied. The result shows that the drag coefficient increases with the decrease of distance, while it increases with the increase of attack angle. There exists attraction force when UUV moves close to the sea bottom, and the attraction force increases with the decrease in distance. The lift coefficient increases with the increase in attack angle. The absolute value of the pitching moment coefficient increases with the decrease in distance and the increase in attack angle.

A Study on the Environmental Standard of Sediment on the Bottom of the Water

Energy Technology Data Exchange (ETDEWEB)

Lee, Chang Hee; Yoo, Hye Jin [Korea Environment Institute, Seoul (Korea)

2000-12-01

Sediment on the bottom of the water has been considered one of the water pollutants in the environmental management of Korea so treated as a management on pollutants, as you can see the examples in the dragging operation in the polluted sea area. To healthily maintain and conserve the water ecosystem including bottom living things in the water, sediment on the bottom of the water should be recognized as the independent medium, which should maintain the certain quality like the water, the atmosphere, and soil, rather than the source of water pollution. Such recognition means that the management of sediment on the bottom of the water should change the fragmentary goal, centered the post management focusing on the water management, to the ecosystematic goal including the bottom living things. In a point of the view, this study has a great significance to suggest not only the final goal for the management of sediment on the bottom of the water but also the necessity of developing the environmental standard of the sediment on the bottom of the water, which is a standard of the management or judgment in the actual managing the sediment on the bottom of the water - an estimation on the pollution of sediment, a removal of the polluted sediment, a purification of sediment, and an abandonment of the dragged sediment -, and the development measures. Considering the situation that even the basic scheme related to the management of sediment is not prepared in the Government level, the concept of the environmental standard of sediment, the foreign example of the environmental standard of sediment, the current state of the domestic sediment pollution, and the development scheme of the environmental standard in this study must be the important foundation to establish the management system of sediment in the Government level. 121 refs., 10 figs., 45 tabs.

Evaluation of the bottom water reservoir VAPEX process

Energy Technology Data Exchange (ETDEWEB)

Frauenfeld, T.W.J.; Jossy, C.; Kissel, G.A. [Alberta Research Council, Devon, AB (Canada); Rispler, K. [Saskatchewan Research Council, Saskatoon, SK (Canada)

2004-07-01

The mobilization of viscous heavy oil requires the dissolution of solvent vapour into the oil as well as the diffusion of the dissolved solvent into the virgin oil. Vapour extraction (VAPEX) is an enhanced oil recovery (EOR) process which involves injecting a solvent into the reservoir to reduce the viscosity of hydrocarbons. This paper describes the contribution of the Alberta Research Council to solvent-assisted oil recovery technology. The bottom water process was also modelled to determine its feasibility for a field-scale oil recovery scheme. Several experiments were conducted in an acrylic visual model in which Pujol and Boberg scaling were used to produce a lab model scaling a field process. The model simulated a slice of a 30 metre thick reservoir, with a 10 metre thick bottom water zone, containing two horizontal wells (25 metres apart) at the oil water interface. The experimental rates were found to be negatively affected by continuous low permeability layers and by oil with an initial gas content. In order to achieve commercial oil recovery rates, the bottom water process must be used to increase the surface area exposed to solvents. A large oil water interface between the wells provides contact for solvent when injecting gas at the interface. High production rates are therefore possible with appropriate well spacing. 11 refs., 4 tabs., 16 figs.

An Analysis Model for Water Cone Subsidence in Bottom Water Drive Reservoirs

Science.gov (United States)

Wang, Jianjun; Xu, Hui; Wu, Shucheng; Yang, Chao; Kong, lingxiao; Zeng, Baoquan; Xu, Haixia; Qu, Tailai

2017-12-01

Water coning in bottom water drive reservoirs, which will result in earlier water breakthrough, rapid increase in water cut and low recovery level, has drawn tremendous attention in petroleum engineering field. As one simple and effective method to inhibit bottom water coning, shut-in coning control is usually preferred in oilfield to control the water cone and furthermore to enhance economic performance. However, most of the water coning researchers just have been done on investigation of the coning behavior as it grows up, the reported studies for water cone subsidence are very scarce. The goal of this work is to present an analytical model for water cone subsidence to analyze the subsidence of water cone when the well shut in. Based on Dupuit critical oil production rate formula, an analytical model is developed to estimate the initial water cone shape at the point of critical drawdown. Then, with the initial water cone shape equation, we propose an analysis model for water cone subsidence in bottom water reservoir reservoirs. Model analysis and several sensitivity studies are conducted. This work presents accurate and fast analytical model to perform the water cone subsidence in bottom water drive reservoirs. To consider the recent interests in development of bottom drive reservoirs, our approach provides a promising technique for better understanding the subsidence of water cone.

Study of droplet flow in a T-shape microchannel with bottom wall fluctuation

Science.gov (United States)

Pang, Yan; Wang, Xiang; Liu, Zhaomiao

2018-03-01

Droplet generation in a T-shape microchannel, with a main channel width of 50 μm , side channel width of 25 μm, and height of 50 μm, is simulated to study the effects of the forced fluctuation of the bottom wall. The periodic fluctuations of the bottom wall are applied on the near junction part of the main channel in the T-shape microchannel. Effects of bottom wall's shape, fluctuation periods, and amplitudes on the droplet generation are covered in the research of this protocol. In the simulation, the average size is affected a little by the fluctuations, but significantly by the fixed shape of the deformed bottom wall, while the droplet size range is expanded by the fluctuations under most of the conditions. Droplet sizes are distributed in a periodic pattern with small amplitude along the relative time when the fluctuation is forced on the bottom wall near the T-junction, while the droplet emerging frequency is not varied by the fluctuation. The droplet velocity is varied by the bottom wall motion, especially under the shorter period and the larger amplitude. When the fluctuation period is similar to the droplet emerging period, the droplet size is as stable as the non-fluctuation case after a development stage at the beginning of flow, while the droplet velocity is varied by the moving wall with the scope up to 80% of the average velocity under the conditions of this investigation.

A Comprehensive Review on the Properties of Coal Bottom Ash in Concrete as Sound Absorption Material

Directory of Open Access Journals (Sweden)

Ramzi Hannan Nurul Izzati Raihan

2017-01-01

Full Text Available The government is currently implementing policies to increase the usage of coal as fuel for electricity generation. At the same time, the dependency on gas will be reduced. In addition, coal power plants in Malaysia produce large amounts of industrial waste such as bottom ash which is collected in impoundment ponds (ash pond. However, millions of tons of coal ash (bottom ash waste are collected in ponds near power plant stations. Since bottom ash has been classified as hazardous material that threatens the health and safety of human life, an innovative and sustainable solution has been introduced to reuse or recycle industrial waste such as coal bottom ash in concrete mixtures to create a greener and more sustainable world. Bottom ash has the potential to be used as concrete material to replace fine aggregates, coarse aggregates or both. Hence, this paper provides an overview of previous research which used bottom ash as fine aggregate replacement in conventional concrete. The workability, compressive strength, flexural strength, and sound absorption of bottom ash in concrete are reviewed.

An analytical evaluation for the pressure drop characteristics of bottom nozzle flow holes

International Nuclear Information System (INIS)

Yang, S. G.; Kim, H. J.; Lim, H. T.; Park, E. J.; Jeon, K. L.

2002-01-01

An analytical evaluation for the bottom nozzle flow holes was performed to find a best design concept in terms of pressure drop. For this analysis, Computational Fluid Dynamics (CFD), FLUENT 5.5, code was selected as an analytical evaluation tool. The applicability of CFD code was verified by benchmarking study with Vibration Investigation of Small-scale Test Assemblies (VISTA) test data in several flow conditions and typical flow hole shape. From this verification, the analytical data were benchmarked roughly within 17% to the VISTA test data. And, overall trend under various flow conditions looked very similar between both cases. Based on the evaluated results using CFD code, it is concluded that the deburring and multiple chamfer hole features at leading edge are the excellent design concept to decrease pressure drop across bottom nozzle plate. The deburring and multiple chamfer hole features at leading edge on the bottom nozzle plate have 12% and 17% pressure drop benefit against a single chamfer hole feature on the bottom nozzle plate, respectively. These design features are meaningful and applicable as a low pressure drop design concept of bottom nozzle for Pressurized Water Reactor (PWR) fuel assembly

Uranium isotopes in waters and bottom sediments of rivers and lakes in Poland

International Nuclear Information System (INIS)

Pietrzak-Flis, Z.; Kaminska, I.; Chrzanowski, E.

2004-01-01

Activity concentrations of 238 U, 234 U and 235 U were determined in waters and bottom sediments in two main rivers in Poland (the Vistula and Odra rivers) with their tributaries, in four coastal rivers and six lakes. Concentration of 238 U and 233 U were compared with the concentrations of 226 Ra determined in another study. As compared with concentrations in coastal rivers and in lakes, enhanced concentrations of the radionuclides were observed in water and bottom sediments in the upper and middle courses of Vistula river, whereas in the Odra river the enhanced concentrations were present only in the bottom sediments. The enhanced concentrations in the Vistula river result from the discharge of coal mine waters from the Upper Silesian Coal Basin, and they indicate that the discharge was continued. The enhanced concentration in Odra river observed only in bottom sediments indicate that the discharge occurred in the past. The 234 U/ 238 U ratio for the bottom sediments was close to unity, indicating that these isotopes were close to equilibrium, whereas for water the average ratio was form 1.2 for lakes to 1.5 for the Vistula river, demonstrating the lack of equilibrium. (author)

Modified Back Contact Interface of CZTSe Thin Film Solar Cells: Elimination of Double Layer Distribution in Absorber Layer.

Science.gov (United States)

Zhang, Zhaojing; Yao, Liyong; Zhang, Yi; Ao, Jianping; Bi, Jinlian; Gao, Shoushuai; Gao, Qing; Jeng, Ming-Jer; Sun, Guozhong; Zhou, Zhiqiang; He, Qing; Sun, Yun

2018-02-01

Double layer distribution exists in Cu 2 SnZnSe 4 (CZTSe) thin films prepared by selenizing the metallic precursors, which will degrade the back contact of Mo substrate to absorber layer and thus suppressing the performance of solar cell. In this work, the double-layer distribution of CZTSe film is eliminated entirely and the formation of MoSe 2 interfacial layer is inhibited successfully. CZTSe film is prepared by selenizing the precursor deposited by electrodeposition method under Se and SnSe x mixed atmosphere. It is found that the insufficient reaction between ZnSe and Cu-Sn-Se phases in the bottom of the film is the reason why the double layer distribution of CZTSe film is formed. By increasing Sn content in the metallic precursor, thus making up the loss of Sn because of the decomposition of CZTSe and facilitate the diffusion of liquid Cu 2 Se, the double layer distribution is eliminated entirely. The crystallization of the formed thin film is dense and the grains go through the entire film without voids. And there is no obvious MoSe 2 layer formed between CZTSe and Mo. As a consequence, the series resistance of the solar cell reduces significantly to 0.14 Ω cm 2 and a CZTSe solar cell with efficiency of 7.2% is fabricated.

Non-charm hadronic decays of bottom baryons

International Nuclear Information System (INIS)

Kohara, Y.

1999-01-01

Two-body decay amplitudes of antitriplet bottom baryons Λ 0b , Θ 0 b and Θ -b to a decuplet baryon and a pseudoscalar meson are analyzed on the basis of the quark diagram scheme. Relations among the various decay rates to decuplet baryons are derived

Mapping practices of project management – merging top-down and bottom-up perspectives

DEFF Research Database (Denmark)

Thuesen, Christian

2015-01-01

This paper presents a new methodology for studying different accounts of project management practices based on network mapping and analysis. Drawing upon network mapping and visualization as an analytical strategy top-down and bottom-up accounts of project management practice are analysed...... and compared. The analysis initially reveals a substantial difference between the top-down and bottom-up accounts of practice. Furthermore it identifies a soft side of project management that is central in the bottom-up account but absent from the top-down. Finally, the study shows that network mapping...

Bottom-up and top-down effects on plant communities

DEFF Research Database (Denmark)

Souza, Lara; Zelikova, Tamara Jane; Sanders, Nate

2016-01-01

-down) and soil nitrogen (bottom-up) were manipulated over six years in an existing old-field community. We tracked plant α and β diversity - within plot richness and among plot biodiversity- and aboveground net primary productivity (ANPP) over the course of the experiment. We found that bottom-up factors...... affected ANPP while top-down factors influenced plant community structure. Across years, while N reduction lowered ANPP by 10%, N reduction did not alter ANPP relative to control plots. Further, N reduction lowered ANPP by 20% relative to N addition plots. On the other hand, the reduction of insect...... community composition via shifts in plant dominance....

Tunnel magnetoresistance in asymmetric double-barrier magnetic tunnel junctions

International Nuclear Information System (INIS)

Useinov, N.Kh.; Petukhov, D.A.; Tagirov, L.R.

2015-01-01

The spin-polarized tunnel conductance and tunnel magnetoresistance (TMR) through a planar asymmetric double-barrier magnetic tunnel junction (DBMTJ) have been calculated using quasi-classical model. In DBMTJ nanostructure the magnetization of middle ferromagnetic metal layer can be aligned parallel or antiparallel with respect to the fixed magnetizations of the top and bottom ferromagnetic electrodes. The transmission coefficients of an electron to pass through the barriers have been calculated in terms of quantum mechanics. The dependencies of tunnel conductance and TMR on the applied voltage have been calculated in case of non-resonant transmission. Estimated in the framework of our model, the difference between the spin-channels conductances at low voltages was found relatively large. This gives rise to very high magnitude of TMR. - Highlights: • The spin-polarized conductance through the junction is calculated. • Dependencies of the tunnel conductance vs applied bias are shown. • Bias voltage dependence of tunnel magnetoresistance for the structure is shown

Weaver Bottoms Wildlife Habitat Restoration: A Case Study

National Research Council Canada - National Science Library

Davis, Mary M; Damberg, Carol

1994-01-01

.... The Weaver Bottoms Rehabilitation Project is a large scale wetland restoration project that is directed at regaining lost habitat by creating hydrological and energy conditions conducive to marsh growth and production. Davis et al. (1993...

Net-bottom Cage Inserts for Water Bird Casualties

Directory of Open Access Journals (Sweden)

Jackie Belle

2017-10-01

Full Text Available My Bright Idea is a net-bottomed cage insert, which is used to support pelagic avian casualties. The idea was designed and modified by the International Bird Rescue in California (Bird Rescue.

Bottom-quark effects in Higgs production at intermediate transverse momentum arXiv

CERN Document Server

Caola, Fabrizio; Melnikov, Kirill; Monni, Pier Francesco; Tancredi, Lorenzo; Wever, Christopher

We provide a precise description of the Higgs boson transverse momentum distribution including top and bottom quark contributions, that is valid for transverse momenta in the range mb < pt < mt, where mb and mt are the bottom and top quark masses. This description is based on a combination of fixed next-to-leading order (NLO) results with next-to-next-to-leading logarithmic (NNLL) transverse momentum resummation. We show that ambiguities in the resummation procedure for the b-quark loops are of the same order as the related fixed-order uncertainties. We conclude that the current uncertainty in the top-bottom interference contribution to the Higgs transverse momentum spectrum is O(20%).

Interaction of random wave-current over uneven and porous bottoms

International Nuclear Information System (INIS)

Suo Yaohong; Zhang Zhonghua; Zhang Jiafan; Suo Xiaohong

2009-01-01

Starting from linear wave theory and applying Green's second identity and considering wave-current interaction for porous bottoms and variable water depth, the comprehensive mild-slope equation model theory of wave-current interaction is developed, then paying attention to the effect of random waves, by use of Kubo et al.'s method, a model theory of the interaction between random waves and current over uneven and porous bottoms is established. Finally the characteristics of the random waves are discussed numerically from both the geometric-optics approximation and the target spectrum.

Morphology of bottom surfaces of glacier ice tongues in the East Antarctic region

Energy Technology Data Exchange (ETDEWEB)

Bianchi, C.; Chiappini, M.; Zirizzotti, A.; Zuccheretti, E. [Istituto Nazionale di Geofisica e Vulcanologia, Rome (Italy); Tabacco, I. E. [Milan Univ., Milan (Italy). Sez. Geofisica; Passerini, A. [Milan Univ. Bicocca, Milan (Italy). Dipt. di Fisica

2001-02-01

During three Antarctic summer campaigns (1995/97/99) Radio Echo Sounding (RES) system data from some glacier ice tongues in the East Antarctic regions between Victoria Land and George 5. Land were collected. The morphology and structure of the bottom surfaces deduced from the electromagnetic interpretation of echo signal were observed. The bottom surfaces at the ice/water interface show either irregular or flat contours or both. Some ice tongues are nearly perfectly flat, others show clear signs of irregularities while three of them have good regular spaced rippled bottom surfaces. The latter structures are well-evident in the longitudinal traverse of the tongues, whereas the transversal paths do not show the same features. This particular shape of the bottom surfaces related to the ablation process and detachment mechanism could be interesting especially to determine some physical characteristics and the possible fracture points of the ice tongues.

Morphology of bottom surfaces of glacier ice tongues in the East Antarctic region

Directory of Open Access Journals (Sweden)

E. Zuccheretti

2001-06-01

Full Text Available During three Antarctic summer campaigns (1995/97/99 Radio Echo Sounding (RES system data from some glacier ice tongues in the East Antarctic regions between Victoria Land and George V Land were collected. The morphology and structure of the bottom surfaces deduced from the electromagnetic interpretation of echo signal were observed. The bottom surfaces at the ice/water interface show either irregular or flat contours or both. Some ice tongues are nearly perfectly flat, others show clear signs of irregularities while three of them have good regular spaced rippled bottom surfaces. The latter structures are well-evident in the longitudinal traverse of the tongues, whereas the transversal paths do not show the same features. This particular shape of the bottom surfaces related to the ablation process and detachment mechanism could be interesting especially to determine some physical characteristics and the possible fracture points of the ice tongues.

Gulf of Maine Cooperative Bottom Longline Survey Database

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — This database is for a bottom longline (fixed gear) survey executed in the western and central Gulf of Maine targeting complex rocky habitats. The survey is operated...

Lime application methods, water and bottom soil acidity in fresh water fish ponds

Directory of Open Access Journals (Sweden)

Queiroz Julio Ferraz de

2004-01-01

Full Text Available Although some methods for determining lime requirement of pond soils are available and commonly used, there is still no consensus on whether it is more effective to apply liming materials to the bottoms of empty ponds or to wait and apply them over the water surface after ponds are filled. There is also little information on how deep lime reacts in pond sediment over time, and whether the depth of reaction is different when liming materials are applied to the water or to the soil. Therefore, three techniques for treating fish ponds with agricultural limestone were evaluated in ponds with clayey soils at a commercial fish farm. Amounts of agricultural limestone equal to the lime requirement of bottom soils were applied to each of three ponds by: direct application over the pond water surface; spread uniformly over the bottom of the empty pond; spread uniformly over the bottom of the empty pond followed by tilling of the bottom. Effectiveness of agricultural limestone applications did not differ among treatment methods. Agricultural limestone also reacted quickly to increase total alkalinity and total hardness of pond water to acceptable concentrations within 2 weeks after application. The reaction of lime to increase soil pH was essentially complete after one to two months, and lime had no effect below a soil depth of 8 cm. Tilling of pond bottoms to incorporate liming materials is unnecessary, and tilling consumes time and is an expensive practice; filled ponds can be limed effectively.

Properties of the water column and bottom derived from Airborne Visible Infrared Imaging Spectrometer (AVIRIS) data

Science.gov (United States)

Lee, Zhongping; Carder, Kendall L.; Chen, Robert F.; Peacock, Thomas G.

2001-06-01

Using Airborne Visible Infrared Imaging Spectrometer (AVIRIS) data as an example, we show in this study that the properties of the water column and bottom of a large, shallow area can be adequately retrieved using a model-driven optimization technique. The simultaneously derived properties include bottom depth, bottom albedo, and water absorption and backscattering coefficients, which in turn could be used to derive concentrations of chlorophyll, dissolved organic matter, and suspended sediments in the water column. The derived bottom depths were compared with a bathymetry chart and a boat survey and were found to agree very well. Also, the derived bottom albedo image shows clear spatial patterns, with end-members consistent with sand and seagrass. The image of absorption and backscattering coefficients indicates that the water is quite horizontally mixed. Without bottom corrections, chlorophyll a retrievals were ˜50 mg m-3, while the retrievals after bottom corrections were tenfold less, approximating real values. These results suggest that the model and approach used work very well for the retrieval of subsurface properties of shallow-water environments even for rather turbid environments like Tampa Bay, Florida.

Control Properties of Bottom Fired Marine Boilers

DEFF Research Database (Denmark)

Solberg, Brian; Andersen, Palle; Karstensen, Claus M. S.

2007-01-01

This paper focuses on model analysis of a dynamic model of a bottom fired one-pass smoke tube boiler. Linearized versions of the model are analyzed and show large variations in system gains at steady state as function of load whereas gain variations near the desired bandwidth are small. An analys...

Bottom Raking Damage to High-Speed Craft

DEFF Research Database (Denmark)

Simonsen, Bo Cerup

1998-01-01

This paper presents a comparative study of the raking damage to high speed craft (HSC) and conventional ships. The analysis is based on a detailed theoretical model for the raking resistance of an assembled ship bottom structure and on the idea that the impact conditions for various ship types have...

Spectroscopy and decays of charm and bottom

International Nuclear Information System (INIS)

Butler, J.N.

1997-10-01

After a brief review of the quark model, we discuss our present knowledge of the spectroscopy of charm and bottom mesons and baryons. We go on to review the lifetimes, semileptonic, and purely leptonic decays of these particles. We conclude with a brief discussion B and D mixing and rare decays

Solidification/stabilization of fly and bottom ash from medical waste incineration facility.

Science.gov (United States)

Anastasiadou, Kalliopi; Christopoulos, Konstantinos; Mousios, Epameinontas; Gidarakos, Evangelos

2012-03-15

In the present work, the stabilization/solidification of fly and bottom ash generated from incinerated hospital waste was studied. The objectives of the solidification/stabilization treatment were therefore to reduce the leachability of the heavy metals present in these materials so as to permit their disposal in a sanitary landfill requiring only a lower degree of environmental protection. Another objective of the applied treatment was to increase the mechanical characteristics of the bottom ash using different amounts of Ordinary Portland Cement (OPC) as a binder. The solidified matrix showed that the cement is able to immobilize the heavy metals found in fly and bottom ash. The TCLP leachates of the untreated fly ash contain high concentrations of Zn (13.2 mg/l) and Pb (5.21 mg/l), and lesser amounts of Cr, Fe, Ni, Cu, Cd and Ba. Cement-based solidification exhibited a compressive strength of 0.55-16.12 MPa. The strength decreased as the percentage of cement loading was reduced; the compressive strength was 2.52-12.7 MPa for 60% cement mixed with 40% fly ash and 6.62-16.12 MPa for a mixture of 60% cement and 40% bottom ash. The compressive strength reduced to 0.55-1.30 MPa when 30% cement was mixed with 70% fly ash, and to 0.90-7.95 MPa when 30% cement was mixed with 70% bottom ash, respectively. Copyright © 2011 Elsevier B.V. All rights reserved.

Searches for supersymmetric partners of the bottom and top quarks with the ATLAS detector

CERN Document Server

Dafinca, Alexandru

"Supersymmetry is a promising candidate theory that could solve the hierarchy problem and explain the dark matter density in the Universe. The ATLAS experiment at the Large Hadron Collider is sensitive to a variety of such supersymmetric models. This thesis reports on a search for pair production of the supersymmetric scalar partners of bottom and top quarks in 20.1 fb$^{-1}$ of $pp$ collisions at a centre-of-mass energy of 8 TeV using the ATLAS experiment. The study focuses on final states with large missing transverse momentum, no electrons or muons and two jets identified as originating from a $b$-quark. This final state can be produced in a $R$-parity conserving minimal supersymmetric scenario, assuming that the scalar bottom decays exclusively to a bottom quark and a neutralino and the scalar top decays to a bottom quark and a chargino, with a small mass difference with the neutralino. As no signal is observed above the Standard Model expectation, competitive exclusion limits are set on scalar bottom and...

Optimization of hydrogen and syngas production from PKS gasification by using coal bottom ash.

Science.gov (United States)

Shahbaz, Muhammad; Yusup, Suzana; Inayat, Abrar; Patrick, David Onoja; Pratama, Angga; Ammar, Muhamamd

2017-10-01

Catalytic steam gasification of palm kernel shell is investigated to optimize operating parameters for hydrogen and syngas production using TGA-MS setup. RSM is used for experimental design and evaluating the effect of temperature, particle size, CaO/biomass ratio, and coal bottom ash wt% on hydrogen and syngas. Hydrogen production appears highly sensitive to all factors, especially temperature and coal bottom ash wt%. In case of syngas, the order of parametric influence is: CaO/biomass>coal bottom ash wt%>temperature>particle size. The significant catalytic effect of coal bottom ash is due to the presence of Fe 2 O 3 , MgO, Al 2 O 3 , and CaO. A temperature of 692°C, coal bottom ash wt% of 0.07, CaO/biomass of 1.42, and particle size of 0.75mm are the optimum conditions for augmented yield of hydrogen and syngas. The production of hydrogen and syngas is 1.5% higher in the pilot scale gasifier as compared to TGA-MS setup. Copyright © 2017 Elsevier Ltd. All rights reserved.

Possible Significance of Early Paleozoic Fluctuations in Bottom Current Intensity, Northwest Iapetus Ocean

Science.gov (United States)

Lash, Gary G.

1986-06-01

Sedimentologic and geochemical characteristics of red and green deep water mudstone exposed in the central Appalachian orogen define climatically-induced fluctuations in bottom current intensity along the northwest flank of the Iapetus Ocean in Early and Middle Ordovician time. Red mudstone accumulated under the influence of moderate to vigorous bottom current velocities in oxygenated bottom water produced during climatically cool periods. Interbedded green mudstone accumulated at greater sedimentation rates, probably from turbidity currents, under the influence of reduced thermohaline circulation during global warming periods. The close association of green mudstone and carbonate turbidites of Early Ordovician (late Tremadocian to early Arenigian) age suggests that a major warming phase occurred at this time. Increasing temperatures reduced bottom current velocities and resulted in increased production of carbonate sediment and organic carbon on the carbonate platform of eastern North America. Much of the excess carbonate sediment and organic carbon was transported into deep water by turbidity currents. Although conclusive evidence is lacking, this eustatic event may reflect a climatic warming phase that followed the postulated glacio-eustatic Black Mountain event. Subsequent Middle Ordovician fluctuations in bottom current intensity recorded by thin red-green mudstone couplets probably reflect periodic growth and shrinkage of an ice cap rather than major glacial episodes.

Tsunami Simulation Method Assimilating Ocean Bottom Pressure Data Near a Tsunami Source Region

Science.gov (United States)

Tanioka, Yuichiro

2018-02-01

A new method was developed to reproduce the tsunami height distribution in and around the source area, at a certain time, from a large number of ocean bottom pressure sensors, without information on an earthquake source. A dense cabled observation network called S-NET, which consists of 150 ocean bottom pressure sensors, was installed recently along a wide portion of the seafloor off Kanto, Tohoku, and Hokkaido in Japan. However, in the source area, the ocean bottom pressure sensors cannot observe directly an initial ocean surface displacement. Therefore, we developed the new method. The method was tested and functioned well for a synthetic tsunami from a simple rectangular fault with an ocean bottom pressure sensor network using 10 arc-min, or 20 km, intervals. For a test case that is more realistic, ocean bottom pressure sensors with 15 arc-min intervals along the north-south direction and sensors with 30 arc-min intervals along the east-west direction were used. In the test case, the method also functioned well enough to reproduce the tsunami height field in general. These results indicated that the method could be used for tsunami early warning by estimating the tsunami height field just after a great earthquake without the need for earthquake source information.

Comparision of Bathymetry and Bottom Characteristics From Hyperspectral Remote Sensing Data and Shipborne Acoustic Measurements

Science.gov (United States)

McIntyre, M. L.; Naar, D. F.; Carder, K. L.; Howd, P. A.; Lewis, J. M.; Donahue, B. T.; Chen, F. R.

2002-12-01

There is growing interest in applying optical remote sensing techniques to shallow-water geological applications such as bathymetry and bottom characterization. Model inversions of hyperspectral remote-sensing reflectance imagery can provide estimates of bottom albedo and depth. This research was conducted in support of the HyCODE (Hyperspectral Coupled Ocean Dynamics Experiment) project in order to test optical sensor performance and the use of a hyperspectral remote-sensing reflectance algorithm for shallow waters in estimating bottom depths and reflectance. The objective of this project was to compare optically derived products of bottom depths and reflectance to shipborne acoustic measurements of bathymetry and backscatter. A set of three high-resolution, multibeam surveys within an 18 km by 1.5 km shore-perpendicular transect 5 km offshore of Sarasota, Florida were collected at water depths ranging from 8 m to 16 m. These products are compared to bottom depths derived from aircraft remote-sensing data collected with the AVIRIS (Airborne Visible-Infrared Imaging Spectrometer) instrument data by means of a semi-analytical remote sensing reflectance model. The pixel size of the multibeam bathymetry and AVIRIS data are 0.25 m and 10 m, respectively. When viewed at full resolution, the multibeam bathymetry data show small-scale sedimentary bedforms (wavelength ~10m, amplitude ~1m) that are not observed in the lower resolution hyperspectral bathymetry. However, model-derived bottom depths agree well with a smoothed version of the multibeam bathymetry. Depths derived from shipborne hyperspectral measurements were accurate within 13%. In areas where diver observations confirmed biological growth and bioturbation, derived bottom depths were less accurate. Acoustic backscatter corresponds well with the aircraft hyperspectral imagery and in situ measurements of bottom reflectance. Acoustic backscatter was used to define the distribution of different bottom types

Pengaruh Kombinasi Fly Ash dan Bottom Ash sebagai Bahan Substitusi pada Campuran Beton terhadap Sifat Mekanis

OpenAIRE

Yahya, Tengku Tantoni; Kurniawandy, Alex; Djauhari, Zulfikar

2017-01-01

Fly ash and bottom ash were waste that generated from the power plant burning coal process. Fly ash and bottom ash has the potential to be developed as a basic ingredient in concrete composites. This research aimed to obtain the properties of fresh concrete and hard concrete of the combined effect of fly ash and bottom ash as a substitute ingredient in composite concrete. This research has examined the influence of a combination of waste fly ash and bottom ash to the compressive strength of a...

The Interplay of Top-Down and Bottom-Up

DEFF Research Database (Denmark)

Winkler, Till; Brown, Carol V.; Ozturk, Pinar

2014-01-01

The exchange of patient health information across different organizations involved in healthcare delivery has potential benefits for a wide range of stakeholders. However, many governments in Europe and in the U.S. have, despite both top-down and bottom-up initiatives, experienced major barriers...... in achieving sustainable models for implementing health information exchange (HIE) throughout their healthcare systems. In the case of the U.S., three years after stimulus funding allocated as part of the 2009 HITECH Act, the extent to which government funding will be needed to sustain health information...... organizations (HIOs) that facilitate HIE across regional stakeholders remains an unanswered question. This research investigates the impacts of top-down and bottom-up initiatives on the evolutionary paths of HIOs in two contingent states in the U.S. (New Jersey and New York) which had different starting...

Bottom-up effects on attention capture and choice

DEFF Research Database (Denmark)

Peschel, Anne; Orquin, Jacob Lund; Mueller Loose, Simone

Attention processes and decision making are accepted to be closely linked together because only information that is attended to can be incorporated in the decision process. Little is known however, to which extent bottom-up processes of attention affect stimulus selection and therefore...... the information available to form a decision. Does changing one visual cue in the stimulus set affect attention towards this cue and what does that mean for the choice outcome? To address this, we conducted a combined eye tracking and choice experiment in a consumer choice setting with visual shelf simulations...... salient. The observed effect on attention also carries over into increased choice likelihood. From these results, we conclude that even small changes in the choice capture attention based on bottom-up processes. Also for eye tracking studies in other domains (e.g. search tasks) this means that stimulus...

49 CFR 179.103-5 - Bottom outlets.

Science.gov (United States)

2010-10-01

.... (a) In addition to or in place of the venting, loading and unloading valves, measuring and sampling... or male and female flange attachment, but in no case shall the breakage groove or equivalent extend... attachment on a pad attached to the outside bottom of the tank. The mounting pad must have a maximum...

Uni-directional waves over slowly varying bottom, part II: Deformation of travelling waves

NARCIS (Netherlands)

Pudjaprasetya, S.R.; Pudjaprasetya, S.R.; van Groesen, Embrecht W.C.

1996-01-01

A new Korteweg-de Vries type of equation for uni-directional waves over slowly varying bottom has been derived in Part I. The equation retains the Hamiltonian structure of the underlying complete set of equations for surface waves. For flat bottom it reduces to the standard Korteweg-de Vries

Measurement of the Z-boson branching fraction into hadrons containing bottom quarks

International Nuclear Information System (INIS)

Kral, J.F.

1990-09-01

We use the Mark II detector to study Z decays into bottom quark-anti-quark pairs, leading to the production of bottom hadrons. The Z bosons are formed in e + e - annihilation at the SLC at center-of-mass energies between 89 and 93 GeV. We identify events containing semileptonic decays of bottom hadrons by detecting isolated leptons, i.e leptons with high transverse momenta relative to the nearest hadronic jet. Using isolated electrons and muons, we measure the B-hadron semileptonic branching ratio times the fraction of hadronic Z decays which contain bottom hadrons, B(B → X ell ν)·Γ(Z → b bar b)/Γ(Z → had) = 0.025 -0.009 +0.100 ± 0.005, where we have listed the statistical errors followed by the systematic error. Assuming B(B → X(ell)ν) = 11% ± 1%, we measure Γ(Z → b bar b)/Γ(Z → had) = 0.23 -0.09 +0.11 , in good agreement with the standard-model prediction of 0.22. We find Γ(Z → b bar b) = 0.40 -0.16 +0.19 GeV. 83 refs., 34 figs., 19 tabs

Lost in translation? Multi-metric macrobenthos indicators and bottom trawling

DEFF Research Database (Denmark)

Gislason, Henrik; Bastardie, Francois; Dinesen, Grete E.

2017-01-01

trawling. We use linear mixed effects models to analyze how bottom trawling intensity affects the indicators used in the Danish (Danish Quality Index, DKI) and Swedish (Benthic Quality Index, BQI) environmental monitoring programs in the Kattegat, the sea area between Sweden and Denmark. Using year...... of individuals per sample (density), we expect species density and density to be positively correlated. This correlation was confirmed by a simulation model and by statistical analysis of the bottom samples in which log species density was highly significantly related to log density (r = 0.75, df = 144, p ...

Bottomonia: open bottom strong decays and spectrum

Directory of Open Access Journals (Sweden)

Santopinto E.

2014-05-01

Full Text Available We present our results for the bottomonium spectrum with self energy corrections. The bare masses used in the calculation are computed within Godfrey and Isgur’s relativized quark model. We also discuss our results for the open bottom strong decay widths of higher bottomonia in the 3P0 pair-creation model.

Seismic evaluation of large flat-bottomed tanks

International Nuclear Information System (INIS)

Kennedy, R.P.; Kassawara, R.P.

1990-01-01

This paper presents a procedure for conservatively evaluating the seismic capacity of flat-bottom fluid storage tanks. The authors know of no case of tank failures at capacity levels less than those predicted by this procedure. Thus, the predicted capacity represents a High Confidence Low Probability of Failure (HCLPF) capacity consistent with earthquake experience. (orig.)

Gammametry of sea bottom in prospecting for minerals. Gammametriya morskogo dna pri poiskakh poleznykh iskopaemykh

Energy Technology Data Exchange (ETDEWEB)

Shatsov, A N [Vsesoyuznyj Nauchno-Issledovatel' skij Inst. Yadernoj Geofiziki i Geokhimii, Moscow (USSR)

1977-01-01

The main aspects of study of the natural gamma field in the geological investigations of sea bottom are considered. Problems of development of sea scintillation radiometers for continuous (in profiles) and discrete, in (in stations) measurements of the natural gamma-radiation of the superficial layer of modern sea sediment and rock of sea bottom in conditions of natural occurence are discussed. The significance of gammametry of shallow-water zones, in the Caspian, Baltic, Black and Japan seas for the study of the geological structure of the sea bottom and its mineral base is shown. Geophysical methods are briefly described which must be used in combination with gammametry of the sea bottom. According to the Soviet and foreign sources the future of using spectrometry of natural and also induced and captured gamma radiation is shown for the study of ferro-manganese and phosphorus concretions, depressions in the sea bottom, filled by highly mineralized brines and silts.

The petroleum industry improving the bottom line

International Nuclear Information System (INIS)

Benner, R.I.

1992-01-01

The oil and gas exploration and production business environment has presented many challenges over the last decade, notably price volatility and rising costs. Managing the margin and changing a company's cost structure to improve the bottom line is a major issue with company executives. The experiences of Oryx Energy Company since its spinoff from Sun Company in 1988 are used as an example of a company makeover. A generalized exploration and production income statement is employed to present industry cost/portfolio relationships and strategies for improving the bottom line. At Oryx, three major strategies were set in place to enhance shareholder value: an increased emphasis on applied technology, including horizontal drilling, advanced 3-dimensional seismic prospecting, and intensive use of interactive computer workstations; international expansion; and an emphasis on the U.S. Gulf of Mexico, deemphasizing the onshore U.S. and the gas processing business. Specific strategies are outlined in the areas of increasing revenues, reducing production cost and exploration expense, and controlling general and administrative expenses. 8 refs., 18 figs., 2 tabs

Biomixing generated by benthic filterfeeders: A diffusion model for near-bottom phytoplankton depletion

DEFF Research Database (Denmark)

Scheel Larsen, Poul; Riisgård, H.U.

1997-01-01

-feeders, the polychaete Nereis diversicolor and the ascidian Ciona intestinalis, respectively. The model is based on sinks located at inhalant openings and Fick's law with an effective diffusivity that decreases with distance above the bottom due to the biomixing generated by exhalant and inhalant feeding currents. For N....... intestinalis, having inhalant and exhalant openings situated about 0.05-0.1 m above the bottom and a higher and inclined exhalant jet velocity of about 0.1-0.2 m s-1, the concentration distributions show a nearly uniform depletion over a layer reaching a thickness of 0.2-0.3 m above the bottom due to high...

Ocean Bottom Seismometers technology: current state and future outlook

Science.gov (United States)

Ilinskiy, Dmitry; Ganzha, Oleg

2016-04-01

The beginning of 2000s was marked by a significant progress in the development and use of self-pop-up sea-bottom seismic recorders (Ocean Bottom Seismometers). In Russia it was a novel solution developed by the Russian Academy of Sciences Experimental Design Bureau of Oceanological Engineering. This recorder and its clones have been widely used not only for the Earth crust studies, but also for investigations of sub-basalt structures and gas hydrate exploration. And what has happened over the last 10 years? Let us look closely at the second generation of ocean bottom stations developed by Geonodal Solutions (GNS) as an illustration of the next step forward in the sea-bottom acquisition technology. First of all, hardware components have changed dramatically. The electronic components became much smaller, accordingly, the power consumption and electronic self-noise were dropped down significantly. This enabled development of compact station 330 mm in diameter instead of previous 450mm. The weight fell by half, while the autonomy increased up to 90 days due to both decreased energy consumption and increased capacity of the batteries. The dynamic range of recorded seismic data has expended as a result of decreased set noise and the application of 24-bit A/D converters. The instruments dimensions have been reduced, power consumption decreased, clock accuracy was significantly improved. At the same time, development of advanced time reference algorithms enabled to retain instrument accuracy around 1 ms during all the autonomous recording period. The high-speed wireless data transfer technology offered a chance to develop "maintenance-free" station throughout its operation time. The station can be re-used at the different sea bottom locations without unsealing of the deep-water container for data download, battery re-charge, clock synchronization. This noticeably reduces the labor efforts of the personnel working with the stations. This is critically important in field

Field measurements of bottom boundary layer and suspend particle materials on Jyoban coast in Japan

International Nuclear Information System (INIS)

Yagi, Hiroshi; Sugimatsu, Kouichi; Nishi, Yoshihiro; Kawamata, Shigeru; Nakayama, Akiyoshi; Udagawa, Toru; Suzuki, Akira

2013-01-01

To understand the characteristics of the bottom boundary layer (BBL), movements of suspended particle material (SPM) and its related radionuclide transport on Jyoban coast, the continuous monitoring of bottom environments using the mooring system and the intensive field survey of BBL with FRA-TRIPOD were performed. The observation results have shown the fundamental characteristics of BBL (vertical distributions of velocities and bottom roughness, etc.) and bottom turbidity variations. The turbidity at the shallow water depth (30 m) was strongly influenced by waves and turbid water generated on rough wave conditions was transported by the coastal currents with the several days period. Turbidities at the deeper depths (80 m and 130 m) were affected by semidiurnal internal tides. (author)

Impressions of the turbulence variability in a weakly stratified, flat-bottom deep-sea ‘boundary layer’

NARCIS (Netherlands)

van Haren, H.

2015-01-01

The character of turbulent overturns in a weakly stratified deep-sea is investigated in some detail using 144 high-resolution temperature sensors at 0.7 m intervals, starting 5 m above the bottom. A 9-day, 1 Hz sampled record from the 912 m depth flat-bottom (<0.5% bottom-slope) mooring site in the

Probing magnetic bottom and crustal temperature variations along the Red Sea margin of Egypt

Science.gov (United States)

Ravat, D.; Salem, A.; Abdelaziz, A.M.S.; Elawadi, E.; Morgan, P.

2011-01-01

Over 50 magnetic bottom depths derived from spectra of magnetic anomalies in Eastern Egypt along the Red Sea margin show variable magnetic bottoms ranging from 10 to 34. km. The deep magnetic bottoms correspond more closely to the Moho depth in the region, and not the depth of 580??C, which lies significantly deeper on the steady state geotherms. These results support the idea of Wasilewski and coworkers that the Moho is a magnetic boundary in continental regions. Reduced-to-pole magnetic highs correspond to areas of Younger Granites that were emplaced toward the end of the Precambrian. Other crystalline Precambrian units formed earlier during the closure of ocean basins are not strongly magnetic. In the north, magnetic bottoms are shallow (10-15. km) in regions with a high proportion of these Younger Granites. In the south, the shoaling of the magnetic bottom associated with the Younger Granites appears to be restricted to the Aswan and Ras Banas regions. Complexity in the variation of magnetic bottom depths may arise due to a combination of factors: i) regions of Younger (Precambrian) Granites with high magnetite content in the upper crust, leaving behind low Curie temperature titanomagnetite components in the middle and lower crust, ii) rise in the depth of 580??C isotherm where the crust may have been heated due to initiation of intense magmatism at the time of the Red Sea rifting (~. 20. Ma), and iii) the contrast of the above two factors with respect to the neighboring regions where the Moho and/or Curie temperature truncates lithospheric ferromagnetism. Estimates of fractal and centroid magnetic bottoms in the oceanic regions of the Red Sea are significantly below the Moho in places suggesting that oceanic uppermost mantle may be serpentinized to the depth of 15-30 km in those regions. ?? 2011 Elsevier B.V.

The desorption of caesium from Peach Bottom HTGR steam generator materials

International Nuclear Information System (INIS)

Clark, M.J.

1979-03-01

The work at Harwell on the Peach Bottom End-of-Life Program in co-operation with the General Atomic Company (U.S.A.) is described. Materials taken from the Economiser, Evaporator and Superheater Sections of the Peach Bottom Unit No. 1. High Temperature Gas Cooled Reactor (HTGR) Heat Exchanger were placed in a reducing atmosphere comparable to the composition of an HTGR helium coolant gas, and the desorption of caesium isotopes measured under known conditions of flow, temperature and oxygen pressure. (author)

Leaching from waste incineration bottom ashes treated in a rotary kiln

DEFF Research Database (Denmark)

Hyks, Jiri; Nesterov, Igor; Mogensen, Erhardt

2011-01-01

Leaching from municipal solid waste incineration bottom ash treated in a rotary kiln was quantified using a combination of lab-scale leaching experiments and geochemical modelling. Thermal treatment in the rotary kiln had no significant effect on the leaching of Al, Ba, Ca, Mg, Si, Sr, Zn, sulfate...... the thermal treatment. Overall, rotary kiln thermal treatment of bottom ashes can be recommended to reduce the leaching of Cu, Pb, Cl and DOC; however, increased leaching of Cr and Mo should be expected....

Repair Mortars and New Concretes with Coal Bottom and Biomass Ashes Using Rheological Optimisation

International Nuclear Information System (INIS)

Bras, A.; Faustino, P.

2016-01-01

The objective of the present work is to analyse the potential of using non-classical additions in concrete and mortar compositions such as coal bottom ash and biomass ash (Bio), as partial replacing binder of ordinary Portland cement. It is intended to deal with production of these type of wastes and its accumulation and contribute to the minimisation of carbon and embodied energy in construction materials. The aim is to identify the concrete and mortars formulation types where it is possible to get more benefit by incorporating bottom ash and Bio. Based on the optimisation of the rheological properties of cement-based materials, mortars with repair function and concrete compositions were developed including 0%, 10%, 15% and 20% of bottom ash and Bio as cement replacement. An assessment of the evolution of relative concrete compressive strength was calculated as a function of the relative solid volume fraction of several concretes. bottom ash compositions present low resistance to high flow rates, increasing the ease of placement and vibration. bottom ash seems to present more filler and pozzolanic effect when compared with Bio. bottom ash mortars fulfil the compressive strength and stiffness requirements to be used as repair mortars, allowing the replacement of 15% or 20% of cement by an industrial waste. This by-product is able to work in the development of the mortar and concrete microstructure strength adopting a much more sustainable solution for the environment.

Bottom Topographic Changes of Poyang Lake During Past Decade Using Multi-temporal Satellite Images

Science.gov (United States)

Zhang, S.

2015-12-01

Poyang Lake, as a well-known international wetland in the Ramsar Convention List, is the largest freshwater lake in China. It plays crucial ecological role in flood storage and biological diversity. Poyang Lake is facing increasingly serious water crises, including seasonal dry-up, decreased wetland area, and water resource shortage, all of which are closely related to progressive bottom topographic changes over recent years. Time-series of bottom topography would contribute to our understanding of the lake's evolution during the past several decades. However, commonly used methods for mapping bottom topography fail to frequently update quality bathymetric data for Poyang Lake restricted by weather and accessibility. These deficiencies have limited our ability to characterize the bottom topographic changes and understanding lake erosion or deposition trend. To fill the gap, we construct a decadal bottom topography of Poyang Lake with a total of 146 time series medium resolution satellite images based on the Waterline Method. It was found that Poyang Lake has eroded with a rate of -14.4 cm/ yr from 2000 to 2010. The erosion trend was attributed to the impacts of human activities, especially the operation of the Three Gorge Dams, sand excavation, and the implementation of water conservancy project. A decadal quantitative understanding bottom topography of Poyang Lake might provide a foundation to model the lake evolutionary processes and assist both researchers and local policymakers in ecological management, wetland protection and lake navigation safety.

Agricultural ammonia emissions in China: reconciling bottom-up and top-down estimates

Directory of Open Access Journals (Sweden)

L. Zhang

2018-01-01

Full Text Available Current estimates of agricultural ammonia (NH3 emissions in China differ by more than a factor of 2, hindering our understanding of their environmental consequences. Here we apply both bottom-up statistical and top-down inversion methods to quantify NH3 emissions from agriculture in China for the year 2008. We first assimilate satellite observations of NH3 column concentration from the Tropospheric Emission Spectrometer (TES using the GEOS-Chem adjoint model to optimize Chinese anthropogenic NH3 emissions at the 1∕2°  ×  2∕3° horizontal resolution for March–October 2008. Optimized emissions show a strong summer peak, with emissions about 50 % higher in summer than spring and fall, which is underestimated in current bottom-up NH3 emission estimates. To reconcile the latter with the top-down results, we revisit the processes of agricultural NH3 emissions and develop an improved bottom-up inventory of Chinese NH3 emissions from fertilizer application and livestock waste at the 1∕2°  ×  2∕3° resolution. Our bottom-up emission inventory includes more detailed information on crop-specific fertilizer application practices and better accounts for meteorological modulation of NH3 emission factors in China. We find that annual anthropogenic NH3 emissions are 11.7 Tg for 2008, with 5.05 Tg from fertilizer application and 5.31 Tg from livestock waste. The two sources together account for 88 % of total anthropogenic NH3 emissions in China. Our bottom-up emission estimates also show a distinct seasonality peaking in summer, consistent with top-down results from the satellite-based inversion. Further evaluations using surface network measurements show that the model driven by our bottom-up emissions reproduces the observed spatial and seasonal variations of NH3 gas concentrations and ammonium (NH4+ wet deposition fluxes over China well, providing additional credibility to the improvements we have made to our

Heavy Metal Contamination of Soils around a Hospital Waste Incinerator Bottom Ash Dumps Site.

Science.gov (United States)

Adama, M; Esena, R; Fosu-Mensah, B; Yirenya-Tawiah, D

2016-01-01

Waste incineration is the main waste management strategy used in treating hospital waste in many developing countries. However, the release of dioxins, POPs, and heavy metals in fly and bottom ash poses environmental and public health concerns. To determine heavy metal (Hg, Pb, Cd, Cr, and Ag) in levels in incinerator bottom ash and soils 100 m around the incinerator bottom ash dump site, ash samples and surrounding soil samples were collected at 20 m, 40 m, 60 m, 80 m, 100 m, and 1,200 m from incinerator. These were analyzed using the absorption spectrophotometer method. The geoaccumulation (I geo) and pollution load indices (PLI) were used to assess the level of heavy metal contamination of surrounding soils. The study revealed high concentrations in mg/kg for, Zn (16417.69), Pb (143.80), Cr (99.30), and Cd (7.54) in bottom ash and these were above allowable limits for disposal in landfill. The study also found soils within 60 m radius of the incinerator to be polluted with the metals. It is recommended that health care waste managers be educated on the implication of improper management of incinerator bottom ash and regulators monitor hospital waste incinerator sites.

Direct Numerical Simulation of Oscillatory Flow Over a Wavy, Rough, and Permeable Bottom

Science.gov (United States)

Mazzuoli, Marco; Blondeaux, Paolo; Simeonov, Julian; Calantoni, Joseph

2018-03-01

The results of a direct numerical simulation of oscillatory flow over a wavy bottom composed of different layers of spherical particles are described. The amplitude of wavy bottom is much smaller in scale than typical bed forms such as sand ripples. The spherical particles are packed in such a way to reproduce a bottom profile observed during an experiment conducted in a laboratory flow tunnel with well-sorted coarse sand. The amplitude and period of the external forcing flow as well as the size of the particles are set equal to the experimental values and the computed velocity field is compared with the measured velocity profiles. The direct numerical simulation allows for the evaluation of quantities, which are difficult to measure in a laboratory experiment (e.g., vorticity, seepage flow velocity, and hydrodynamic force acting on sediment particles). In particular, attention is focused on the coherent vortex structures generated by the vorticity shed by both the spherical particles and the bottom waviness. Results show that the wavy bottom triggers transition to turbulence. Moreover, the forces acting on the spherical particles are computed to investigate the mechanisms through which they are possibly mobilized by the oscillatory flow. It was found that forces capable of mobilizing surface particles are strongly correlated with the particle position above the mean bed elevation and the passage of coherent vortices above them.

Characterisation of MSWI bottom ash for potential use as subbase in Greenlandic road construction

DEFF Research Database (Denmark)

Kirkelund, Gunvor Marie; Jørgensen, Anders Stuhr; Ingeman-Nielsen, Thomas

2012-01-01

of infrastructure due to increased oil and mineral exploitation. Thus, in this study MSWI bottom ash from a Greenlandic incinerator was tested for possible reuse as subbase in road construction. The mechanical properties (grain size distribution, wear resistance and bearing capacity) showed that the bottom ash...... grain sizes and could be reduced by removing some of these smaller grain sizes to obtain the stability requirement of the bottom ash. All in all, this study showed that the Greenlandic bottom ash has potential for being reused in road construction....... was acceptable for reuse after some small adjustments in the grain size distribution to prevent frost sensitivity. Results obtained from heavy metal content and heavy metal leaching complied with the Danish guideline values for reuse of waste materials in construction. Leaching of Cu and Cr was high from small...

Response of benthic fauna to experimental bottom fishing

NARCIS (Netherlands)

Sciberras, Marija; Hiddink, Jan Geert; Jennings, Simon; Szostek, Claire L.; Hughes, Kathryn M.; Kneafsey, Brian; Clarke, Leo J.; Ellis, Nick; Rijnsdorp, Adriaan D.; Mcconnaughey, Robert A.; Hilborn, Ray; Collie, Jeremy S.; Pitcher, C.R.; Amoroso, Ricardo O.; Parma, Ana M.; Suuronen, Petri; Kaiser, Michel J.

2018-01-01

Bottom-contact fishing gears are globally the most widespread anthropogenic sources of direct disturbance to the seabed and associated biota. Managing these fishing disturbances requires quantification of gear impacts on biota and the rate of recovery following disturbance. We undertook a systematic

RELATING BOTTOM QUARK MASS IN DR-BAR AND MS-BAR REGULARIZATION SCHEMES

International Nuclear Information System (INIS)

2002-01-01

The value of the bottom quark mass at Q = M Z in the (bar D)(bar R) scheme is an important input for the analysis of supersymmetric models with a large value of tan β. Conventionally, however, the running bottom quark mass extracted from experimental data is quoted in the (bar M)(bar S) scheme at the scale Q = m b . We describe a two loop procedure for the conversion of the bottom quark mass from (bar M)(bar S) to (bar D)(bar R) scheme. The Particle Data Group value m b # bar M# # bar S#(m b # bar M# # bar S#) = 4.2 ± 0.2 GeV corresponds to a range of 2.65-3.03 GeV for m b # bar D# # bar R#(M Z )

Method for cooling a breeder reactor and breeder reactor for applying the method

International Nuclear Information System (INIS)

Gast, K.

1977-01-01

The fuel assemblies of the fission zone and the breeder subassemblies in the radial breeding blanket are supported on a double bottom. The coolant gets into the interspace of the double bottom below the blanket. This part of the space is separated from the interspace of the double bottom below the fission zone. Each breeder subassembly consists of a twin tube. The coolant enters the inner tube, flows through it upwards in axial direction, is then deflected on the upper end, and afterwards, in the annulus of the twin tube, flows down again in axial direction into the inlet region, below the double bottom. From there on it flows upwards through the fuel assemblies of the fission zone from below. Thereby a uniformly high coolant outlet temperature is obtained. (DG) [de

Some Approaches to the Analysis and Interpretation of Wide-Angle Bottom Loss Data.

Science.gov (United States)

1982-02-15

different mechanisms which cause acoustic energy to be lost in the ocean bottom. It is, however, a very significant parameter in predicting bottom loss...Model Based on Numerical Integration," J. Acoust. Soc. Am. 64, 1470. Helmberger, D. V., G. Engen , and P. Scott, 1979. "A Note on Velocity, Density, and

Speciation of Chromium in Bottom Ash Obtained by the Incineration of the Leather Waste Shavings

OpenAIRE

k. louhab; H. Assas

2006-01-01

The evolution of bottom ash morphology and chromium metals behavior during incineration of a leather waste shavings at different incineration temperature have been studied. The Cr, Ca, Mg, Cl rates in bottom ashes, flay ashes and emitted gases in different incineration temperature of the tannery wastes are also determined. The morphology of the bottom ashes obtained by incineration at different temperature from the leather waste shavings was examined by MEB. The result sho...

Exergy analysis of a combined vapor power cycle and boiler flue gas driven double effect water–LiBr absorption refrigeration system

International Nuclear Information System (INIS)

Talukdar, K.; Gogoi, T.K.

2016-01-01

Highlights: • A combined vapor power and double effect water–LiBr absorption refrigeration system is proposed. • The flue gas of the power cycle boiler is the heat source for the double effect refrigeration system. • Energy and exergy analyses are performed to evaluate performance of the combined system. • Effect of high pressure generator temperature on combined system performance is highlighted. • Comparison is provided with a single effect absorption system integrated combined system. - Abstract: A combined vapor power cycle (PC) and double effect water–LiBr absorption refrigeration system (ARS) is proposed in this study. The boiler leaving flue gas of the PC is the heat source for the high pressure generator (HPG) of the double effect ARS. Exergy analysis of the proposed system is performed to show the performance variation of both the topping PC and the bottoming ARS with changing HPG temperature from 120 °C to 150 °C. Further the performance of double effect ARS integrated combined power and cooling system is compared with a similar system integrated with a single effect ARS. HPG temperature of the double effect ARS and generator temperature of the single effect ARS are considered as 120 °C and 80 °C respectively. Results show that the power and efficiency of the topping PC decreases with HPG temperature due to reduction in steam generation rate in the boiler. COP and exergy efficiency of the double effect ARS also reduces with increasing HPG temperature. The irreversible losses in the PC components decrease while the total irreversibility of the combined power and cooling system increases with HPG temperature due to increase in exergy loss with the HPG leaving flue gas and irreversibility of the ARS components. PC performance does not vary much due to replacement of the double effect ARS with the single effect ARS, however higher COP and exergy efficiency of the double effect system are achieved with much lower irreversible losses in the

Investigation on Leaching Behaviour of Fly Ash and Bottom Ash Replacement in Self-Compacting Concrete

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

Fly ash and bottom ash are some of the waste generated by coal-fired power plants, which contains large quantities of toxic and heavy metals. In recent years, many researchers have been interested in studying on the properties of self-compacting concrete incorporated with fly ash and bottom ash but there was very limited research from the combination of fly ash and bottom ash towards the environmental needs. Therefore, this research was focused on investigating the leachability of heavy metals of SCC incorporated with fly ash and bottom ash by using Toxicity Characteristic Leaching Procedure, Synthetic Precipitation Leaching Procedure and Static Leaching Test. The samples obtained from the coal-fired power plant located at Peninsula, Malaysia. In this study, the potential heavy metals leached out from SCC that is produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a substitute for sand with the ratios from 10% to 30% respectively were designated and cast. There are eight heavy metals of concern such as As, Cr, Pb, Zn, Cu, Ni, Mn and Fe. The results indicated that most of the heavy metals leached below the permissible limits from the United States Environmental Protection Agency and World Health Organization limit for drinking water. As a conclusion, the minimum leaching of the heavy metals from the incorporation of fly ash and bottom ash in self-compacting concrete was found in 20% of fly ash and 20% of bottom ash replacement. The results also indicate that this incorporation could minimize the potential of environmental problems.

Thermo-economic comparative analysis of gas turbine GT10 integrated with air and steam bottoming cycle

Science.gov (United States)

Czaja, Daniel; Chmielnak, Tadeusz; Lepszy, Sebastian

2014-12-01

A thermodynamic and economic analysis of a GT10 gas turbine integrated with the air bottoming cycle is presented. The results are compared to commercially available combined cycle power plants based on the same gas turbine. The systems under analysis have a better chance of competing with steam bottoming cycle configurations in a small range of the power output capacity. The aim of the calculations is to determine the final cost of electricity generated by the gas turbine air bottoming cycle based on a 25 MW GT10 gas turbine with the exhaust gas mass flow rate of about 80 kg/s. The article shows the results of thermodynamic optimization of the selection of the technological structure of gas turbine air bottoming cycle and of a comparative economic analysis. Quantities are determined that have a decisive impact on the considered units profitability and competitiveness compared to the popular technology based on the steam bottoming cycle. The ultimate quantity that can be compared in the calculations is the cost of 1 MWh of electricity. It should be noted that the systems analyzed herein are power plants where electricity is the only generated product. The performed calculations do not take account of any other (potential) revenues from the sale of energy origin certificates. Keywords: Gas turbine air bottoming cycle, Air bottoming cycle, Gas turbine, GT10

Improving Heat Transfer at the Bottom of Vials for Consistent Freeze Drying with Unidirectional Structured Ice.

Science.gov (United States)

Rosa, Mónica; Tiago, João M; Singh, Satish K; Geraldes, Vítor; Rodrigues, Miguel A

2016-10-01

The quality of lyophilized products is dependent of the ice structure formed during the freezing step. Herein, we evaluate the importance of the air gap at the bottom of lyophilization vials for consistent nucleation, ice structure, and cake appearance. The bottom of lyophilization vials was modified by attaching a rectified aluminum disc with an adhesive material. Freezing was studied for normal and converted vials, with different volumes of solution, varying initial solution temperature (from 5°C to 20°C) and shelf temperature (from -20°C to -40°C). The impact of the air gap on the overall heat transfer was interpreted with the assistance of a computational fluid dynamics model. Converted vials caused nucleation at the bottom and decreased the nucleation time up to one order of magnitude. The formation of ice crystals unidirectionally structured from bottom to top lead to a honeycomb-structured cake after lyophilization of a solution with 4% mannitol. The primary drying time was reduced by approximately 35%. Converted vials that were frozen radially instead of bottom-up showed similar improvements compared with normal vials but very poor cake quality. Overall, the curvature of the bottom of glass vials presents a considerable threat to consistency by delaying nucleation and causing radial ice growth. Rectifying the vials bottom with an adhesive material revealed to be a relatively simple alternative to overcome this inconsistency.

Importance of the Gulf of Aqaba for the formation of bottom water in the Red Sea

Science.gov (United States)

Plähn, Olaf; Baschek, Burkard; Badewien, Thomas H.; Walter, Maren; Rhein, Monika

2002-08-01

Conductivity-temperature-depth tracer and direct current measurements collected in the northern Red Sea in February and March 1999 are used to study the formation of deep and bottom water in that region. Historical data showed that open ocean convection in the Red Sea can contribute to the renewal of intermediate or deep water but cannot ventilate the bottom water. The observations in 1999 showed no evidence for open ocean convection in the Red Sea during the winter 1998/1999. The overflow water from the Gulf of Aqaba was found to be the densest water mass in the northern Red Sea. An anomaly of the chlorofluorocarbon component CFC-12 observed in the Gulf of Aqaba and at the bottom of the Red Sea suggests a strong contribution of this water mass to the renewal of bottom water in the Red Sea. The CFC data obtained during this cruise are the first available for this region. Because of the new signal, it is possible for the first time to subdivide the deep water column into deep and bottom water in the northern Red Sea. The available data set also shows that the outflow water from the Gulf of Suez is not dense enough to reach down to the bottom of the Red Sea but was found about 250 m above the bottom.

The footprint of bottom trawling in European waters

NARCIS (Netherlands)

Eigaard, Ole R.; Bastardie, Francois; Hintzen, Niels T.; Buhl-Mortensen, Lene; Buhl-Mortensen, Pål; Catarino, Rui; Dinesen, Grete E.; Egekvist, Josefine; Fock, Heino O.; Geitner, Kerstin; Gerritsen, Hans D.; González, Manuel Marín; Jonsson, Patrik; Kavadas, Stefanos; Laffargue, Pascal; Lundy, Mathieu; Gonzalez-Mirelis, Genoveva; Nielsen, J.R.; Papadopoulou, Nadia; Posen, Paulette E.; Pulcinella, Jacopo; Russo, Tommaso; Sala, Antonello; Silva, Cristina; Smith, Christopher J.; Vanelslander, Bart; Rijnsdorp, Adriaan D.

2017-01-01

Mapping trawling pressure on the benthic habitats is needed as background to support an ecosystem approach to fisheries management. The extent and intensity of bottom trawling on the European continental shelf (0-1000 m) was analysed from logbook statistics and vessel monitoring system data for

The analysis of bottom forming process for hybrid heating device

Science.gov (United States)

Bałon, Paweł; Świątoniowski, Andrzej; Kiełbasa, Bartłomiej

2017-10-01

In this paper the authors present an unusual method for bottom forming applicable for various industrial purposes including the manufacture of water heaters or pressure equipment. This method allows for the fabrication of the bottom of a given piece of stainless steel into a pre-determined shape conforming to the DIN standard which determines the most advantageous dimensions for the bottom cross section in terms of working pressure loading. The authors checked the validity of the method in a numerical and experimental way generating a tool designed to produce bottoms of specified geometry. Many problems are encountered during the design and production of parts, especially excessive sheet wrinkling over a large area of the part. The experiment showed that a lack of experience and numerical analysis in the design of such elements would result in the production of highly wrinkled parts. This defect would render the parts impossible to assemble with the cylindrical part. Many tool shops employ a method for drawing elements with a spherical surface which involves additional spinning, stamping, and grading operations, which greatly increases the cost of parts production. The authors present and compare two forming methods for spherical and parabolic objects, and experimentally confirm the validity of the sheet reversing method with adequate pressure force. The applied method produces parts in one drawing operation and in a following operation that is based on laser or water cutting to obtain a round blank. This reduces the costs of tooling manufacturing by requiring just one tool which can be placed on any hydraulic press with a minimum force of 2 000 kN.

A mechanical comparison of linear and double-looped hung supplemental heavy chain resistance to the back squat: a case study.

Science.gov (United States)

Neelly, Kurt R; Terry, Joseph G; Morris, Martin J

2010-01-01

A relatively new and scarcely researched technique to increase strength is the use of supplemental heavy chain resistance (SHCR) in conjunction with plate weights to provide variable resistance to free weight exercises. The purpose of this case study was to determine the actual resistance being provided by a double-looped versus a linear hung SHCR to the back squat exercise. The linear technique simply hangs the chain directly from the bar, whereas the double-looped technique uses a smaller chain to adjust the height of the looped chain. In both techniques, as the squat descends, chain weight is unloaded onto the floor, and as the squat ascends, chain weight is progressively loaded back as resistance. One experienced and trained male weight lifter (age = 33 yr; height = 1.83 m; weight = 111.4 kg) served as the subject. Plate weight was set at 84.1 kg, approximately 50% of the subject's 1 repetition maximum. The SHCR was affixed to load cells, sampling at a frequency of 500 Hz, which were affixed to the Olympic bar. Data were collected as the subject completed the back squat under the following conditions: double-looped 1 chain (9.6 kg), double-looped 2 chains (19.2 kg), linear 1 chain, and linear 2 chains. The double-looped SHCR resulted in a 78-89% unloading of the chain weight at the bottom of the squat, whereas the linear hanging SHCR resulted in only a 36-42% unloading. The double-looped technique provided nearly 2 times the variable resistance at the top of the squat compared with the linear hanging technique, showing that attention must be given to the technique used to hang SHCR.

Glass-ceramic from mixtures of bottom ash and fly ash.

Science.gov (United States)

Vu, Dinh Hieu; Wang, Kuen-Sheng; Chen, Jung-Hsing; Nam, Bui Xuan; Bac, Bui Hoang

2012-12-01

Along with the gradually increasing yield of the residues, appropriate management and treatment of the residues have become an urgent environmental protection problem. This work investigated the preparation of a glass-ceramic from a mixture of bottom ash and fly ash by petrurgic method. The nucleation and crystallization kinetics of the new glass-ceramic can be obtained by melting the mixture of 80% bottom ash and 20% fly ash at 950 °C, which was then cooled in the furnace for 1h. Major minerals forming in the glass-ceramics mainly are gehlenite (Ca(2)Al(2)SiO(7)) & akermanite (Ca(2)MgSiO(7)) and wollastonite (CaSiO(3)). In addition, regarding chemical/mechanical properties, the chemical resistance showing durability, and the leaching concentration of heavy metals confirmed the possibility of engineering and construction applications of the most superior glass-ceramic product. Finally, petrurgic method of a mixture of bottom ash and fly ash at 950 °C represents a simple, inexpensive, and energy saving method compared with the conventional heat treatment. Copyright © 2012 Elsevier Ltd. All rights reserved.

The study of the stress - strain state of the tank with bottom water drainage during operation

Science.gov (United States)

Shchipkova, Yu V.; Tokarev, V. V.

2018-04-01

Bottom drainage from tank is a current problem in modern tank usage. This article proposes the use of the bottom drainage system from the tank with the shape of the sloped cone to the centre of it. Changing the bottom design alters the stress - strain state to be analyzed in the Ansys. The analysis concluded that the proposed drainage system should be applied.

Single production of an exotic bottom partner at LHC

International Nuclear Information System (INIS)

Álvarez, Ezequiel; Rold, Leandro Da; Vietto, Juan Ignacio Sanchez

2014-01-01

We study single production and detection at the LHC run II of exotic partners of the bottom quark. For masses larger than 1 TeV single production can dominate over pair production that is suppressed due to phase space. The presence of exotic partners of the bottom is motivated in models aiming to solve the A FB b anomaly measured at LEP and SLC. Minimal models of this type with partial compositeness predict, as the lightest bottom partner, a new fermion V of electric charge −4/3, also called mirror. The relevant coupling for our study is a WVb vertex, which yields a signal that corresponds to a hard W, a hard b-jet and a forward light jet. We design a search strategy for the leptonic decay of the W, which avoids the large QCD multijet background and its large uncertainties. We find that the main backgrounds are W+jets and tt-bar, and the key variables to enhance the signal over them are a hard b-jet and the rapidity of the light jet. We determine the discovery reach for the LHC run II, in particular we predict that, for couplings of order ∼g/10, this signal could be detected at a 95% confidence level with a mass up to 2.4 TeV using the first 100 fb −1

Preparation of footing bottom of Temelin nuclear powerplant reactors

International Nuclear Information System (INIS)

Vyleta, M.

1988-01-01

The Temelin nuclear power site geologically belongs to the so-called monotonous moldanubium deposit. The site features a range of rocks, from easy to sort out rocks and rocks that can be mined using excavators, to difficult to sort out rocks that are necessary to be broken down, to rocks that are difficult to blast. The table in the main building site area was first lowered by 7 m to a ground elevation of 507.3 m, this in an area of 800x500 m. On the main four production unit sites, the working level of the reactor rooms and the engine rooms was lowered to a ground elevation of 502.3 m. The space of the first main production unit in an area of 70x70 m was excavated down to an elevation of 501.2 m, i.e. 1.1 m above the footing bottom of the first reactor. The technology is described in detail of building the footing bottom, based on the division of the whole area in 70 working fields (7x10 m) in which all working operations proceed in a closed cycle. It was thus guaranteed that the footing bottom would not disturbed with blasting operations or damaged as a result of the movement of building machines and vehicles on exposed rock. (Z.M.). 7 figs., 1 refs

Thorium content in bottom sediments of Pacific and Indian oceans

International Nuclear Information System (INIS)

Gurvich, E.G.; Lisitsyn, A.P.

1980-01-01

Presented are the results of 232 Th distribution study in different substance-genetic types of bottom sediments of Pacific and Indian oceans. Th content determination has been carried out by the method of instrumental neutron activation analysis. Th distribution maps in the surface layer of bottom sediments of Pacific and Indian oceans are drawn. It is noted that Indian ocean sediments are much richer with Th moreover Th distribution in different types of sediments is very non-uniform. Non-uniformity of Th distribution in different types of Pacific ocean sediments is considerably less than that of Indian ocean and exceeds it only in red oozes

Analysis of core damage frequency from internal events: Peach Bottom, Unit 2

International Nuclear Information System (INIS)

Kolaczkowski, A.M.; Lambright, J.A.; Ferrell, W.L.; Cathey, N.G.; Najafi, B.; Harper, F.T.

1986-10-01

This document contains the internal event initiated accident sequence analyses for Peach Bottom, Unit 2; one of the reference plants being examined as part of the NUREG-1150 effort by the Nuclear Regulatory Commission. NUREG-1150 will document the risk of a selected group of nuclear power plants. As part of that work, this report contains the overall core damage frequency estimate for Peach Bottom, Unit 2, and the accompanying plant damage state frequencies. Sensitivity and uncertainty analyses provided additional insights regarding the dominant contributors to the Peach Bottom core damage frequency estimate. The mean core damage frequency at Peach Bottom was calculated to be 8.2E-6. Station blackout type accidents (loss of all ac power) were found to dominate the overall results. Anticipated Transient Without Scram accidents were also found to be non-negligible contributors. The numerical results are largely driven by common mode failure probability estimates and to some extent, human error. Because of significant data and analysis uncertainties in these two areas (important, for instance, to the most dominant scenario in this study), it is recommended that the results of the uncertainty and sensitivity analyses be considered before any actions are taken based on this analysis

Accumulation and potential dissolution of Chernobyl-derived radionuclides in river bottom sediment

International Nuclear Information System (INIS)

Sanada, Yukihisa; Matsunaga, Takeshi; Yanase, Nobuyuki; Nagao, Seiya; Amano, Hikaru; Takada, Hideshige; Tkachenko, Yuri

2002-01-01

Areas contaminated with radionuclides from the Chernobyl nuclear accident have been identified in Pripyat River near the Chernobyl Nuclear Power Plant. The river bottom sediment cores contained 137 Cs (10 5 - 10 6 Bq/m 2 ) within 0-30 cm depth, whose concentration is comparable to that in the ground soil in the vicinity of the nuclear power plant (the Exclusion Zone). The sediment cores also accumulated 90 Sr (10 5 Bq/m 2 ), 239,240 Pu (10 4 Bq/m 2 ) and 241 Am (10 4 Bq/m 2 ) derived from the accident. Several nuclear fuel particles have been preserved at 20-25 cm depth that is the peak area of the concentrations of the radionuclides. Th ese inventories in the bottom sediments were compared with those of the released radionuclides during the accident. An analysis using a selective sequential extraction technique was applied for the radionuclides in the sediments. Results suggest that the possibility of release of 137 Cs and 239,240 Pu from the bottom sediment was low compared with 90 Sr. The potential dissolution and subsequent transport of 90 Sr from the river bottom sediment should be taken into account with respect to the long-term radiological influence on the aquatic environment

Development of debris-resistant bottom end piece

International Nuclear Information System (INIS)

Sohn, Dong Seong; Lee, Jae Kyung; Hwang, Dae Hyun; Yim, Jung Sik; Song, Kee Nam; Oh, Dong Seok; Im, Hyun Tae

1993-01-01

Debris-related fuel failures has been identified to be one of the major causes of fuel failures recently occured in nuclear power plants. In order to reduce the possibility of debris-related fuel failures, it is necessary to prevent the debris from reaching to fuel rods. In this regard, it is important to develop Debris-Resistant Bottom End Piece. (Author)

Area-intensive bottom culture of blue mussels Mytilus edulis in a micro-tidal estuary

DEFF Research Database (Denmark)

Dolmer, Per; Christensen, Helle Torp; Hansen, Benni Winding

2012-01-01

Dredge fishery for blue mussels Mytilus edulis (L.) impacts the benthic ecosystem, and substitution by area-intensive bottom culture production may reduce adverse effects on the ecosystem. Two different field studies in 2007 and 2009 tested the productivity of bottom culture of blue mussels, and ...

Exact Riemann solutions of the Ripa model for flat and non-flat bottom topographies

Science.gov (United States)

Rehman, Asad; Ali, Ishtiaq; Qamar, Shamsul

2018-03-01

This article is concerned with the derivation of exact Riemann solutions for Ripa model considering flat and non-flat bottom topographies. The Ripa model is a system of shallow water equations accounting for horizontal temperature gradients. In the case of non-flat bottom topography, the mass, momentum and energy conservation principles are utilized to relate the left and right states across the step-type bottom topography. The resulting system of algebraic equations is solved iteratively. Different numerical case studies of physical interest are considered. The solutions obtained from developed exact Riemann solvers are compared with the approximate solutions of central upwind scheme.

Observing Double Stars

Science.gov (United States)

Genet, Russell M.; Fulton, B. J.; Bianco, Federica B.; Martinez, John; Baxter, John; Brewer, Mark; Carro, Joseph; Collins, Sarah; Estrada, Chris; Johnson, Jolyon; Salam, Akash; Wallen, Vera; Warren, Naomi; Smith, Thomas C.; Armstrong, James D.; McGaughey, Steve; Pye, John; Mohanan, Kakkala; Church, Rebecca

2012-05-01

Double stars have been systematically observed since William Herschel initiated his program in 1779. In 1803 he reported that, to his surprise, many of the systems he had been observing for a quarter century were gravitationally bound binary stars. In 1830 the first binary orbital solution was obtained, leading eventually to the determination of stellar masses. Double star observations have been a prolific field, with observations and discoveries - often made by students and amateurs - routinely published in a number of specialized journals such as the Journal of Double Star Observations. All published double star observations from Herschel's to the present have been incorporated in the Washington Double Star Catalog. In addition to reviewing the history of visual double stars, we discuss four observational technologies and illustrate these with our own observational results from both California and Hawaii on telescopes ranging from small SCTs to the 2-meter Faulkes Telescope North on Haleakala. Two of these technologies are visual observations aimed primarily at published "hands-on" student science education, and CCD observations of both bright and very faint doubles. The other two are recent technologies that have launched a double star renaissance. These are lucky imaging and speckle interferometry, both of which can use electron-multiplying CCD cameras to allow short (30 ms or less) exposures that are read out at high speed with very low noise. Analysis of thousands of high speed exposures allows normal seeing limitations to be overcome so very close doubles can be accurately measured.

Heavy Metal Contamination of Soils around a Hospital Waste Incinerator Bottom Ash Dumps Site

Directory of Open Access Journals (Sweden)

M. Adama

2016-01-01

Full Text Available Waste incineration is the main waste management strategy used in treating hospital waste in many developing countries. However, the release of dioxins, POPs, and heavy metals in fly and bottom ash poses environmental and public health concerns. To determine heavy metal (Hg, Pb, Cd, Cr, and Ag in levels in incinerator bottom ash and soils 100 m around the incinerator bottom ash dump site, ash samples and surrounding soil samples were collected at 20 m, 40 m, 60 m, 80 m, 100 m, and 1,200 m from incinerator. These were analyzed using the absorption spectrophotometer method. The geoaccumulation (Igeo and pollution load indices (PLI were used to assess the level of heavy metal contamination of surrounding soils. The study revealed high concentrations in mg/kg for, Zn (16417.69, Pb (143.80, Cr (99.30, and Cd (7.54 in bottom ash and these were above allowable limits for disposal in landfill. The study also found soils within 60 m radius of the incinerator to be polluted with the metals. It is recommended that health care waste managers be educated on the implication of improper management of incinerator bottom ash and regulators monitor hospital waste incinerator sites.

Heavy Metal Contamination of Soils around a Hospital Waste Incinerator Bottom Ash Dumps Site

Science.gov (United States)

Adama, M.; Esena, R.; Fosu-Mensah, B.; Yirenya-Tawiah, D.

2016-01-01

Waste incineration is the main waste management strategy used in treating hospital waste in many developing countries. However, the release of dioxins, POPs, and heavy metals in fly and bottom ash poses environmental and public health concerns. To determine heavy metal (Hg, Pb, Cd, Cr, and Ag) in levels in incinerator bottom ash and soils 100 m around the incinerator bottom ash dump site, ash samples and surrounding soil samples were collected at 20 m, 40 m, 60 m, 80 m, 100 m, and 1,200 m from incinerator. These were analyzed using the absorption spectrophotometer method. The geoaccumulation (I geo) and pollution load indices (PLI) were used to assess the level of heavy metal contamination of surrounding soils. The study revealed high concentrations in mg/kg for, Zn (16417.69), Pb (143.80), Cr (99.30), and Cd (7.54) in bottom ash and these were above allowable limits for disposal in landfill. The study also found soils within 60 m radius of the incinerator to be polluted with the metals. It is recommended that health care waste managers be educated on the implication of improper management of incinerator bottom ash and regulators monitor hospital waste incinerator sites. PMID:27034685

The Chicago Fire of 1871: A Bottom Up Approach to Disaster Relief

OpenAIRE

Skarbek, Emily C.

2014-01-01

Can bottom-up relief efforts lead to recovery after disasters? Conventional wisdom and contemporary public policy suggest that major crises require centralized authority to provide disaster relief goods. Using a novel set of comprehensive donation and expenditure data collected from archival records, this paper examines a bottom-up relief effort following one of the most devastating natural disasters of the nineteenth century: the Chicago Fire of 1871. Findings show that while there was no ce...

Subtidal soft-bottom macroinvertebrate communities of the Canary Islands. An ecological approach

OpenAIRE

Monterroso,Oscar; Riera,Rodrigo; Núñez,Jorge

2012-01-01

The Canarian archipelago is characterized by a mosaic of soft-bottoms such as Cymodocea nodosa meadows, Caulerpa spp. meadows, mäerl bottoms, sabellid fields and bare sandy seabeds, including various macroinfaunal communities. Vegetated habitats (e.g. Cymodocea and Caulerpa) maintain more diverse communities than the non-vegetated seabeds. The results indicated that Caulerpa meadows and, to a lesser extent, Cymodocea nodosa and sabellid fields are the richest and most diverse ecosystems in th...

Air bottoming cycle, an alternative to combined cycles. Final report

Energy Technology Data Exchange (ETDEWEB)

Kaikko, J. [Royal Inst. of Techn., Stockholm (Sweden). Dept. of Energy Technology

2001-10-01

In this work, the idea of Air Bottoming Cycle (ABC) has been studied. The objectives for the work have been to establish an understanding of the concept for power and heat generation as well as to find - if possible - feasible concepts for future use in the Swedish energy system. Combined cycle in power generation is an established technology. In the conventional combined cycle, a gas turbine works as a topping cycle together with the steam (Rankine) bottoming cycle. In the ABC the steam bottoming cycle is replaced with a gas turbine (Brayton) bottoming cycle having air as a working fluid. The two gas turbines are thermally connected over a gas-to-gas heat exchanger. This concept promises savings in weight and cost, as well as operating benefits, compared to the Rankine bottoming technology. The ABC has been modelled using a heat balance program, and a parametric study for the concept optimisation as well as for off-design analysis has been performed. Performance of the ABC has been compared to other, established technologies. A preliminary economic evaluation has been made. As a result of the study, it is clarified that the Rankine bottoming cycle with steam remains superior to the ABC as regards electrical efficiency in the medium and large power scale. For small-scale applications (<10 MW{sub e}) where the thermodynamic advantage of the Rankine cycle is not dominating any longer and its economy is burdened by the heavy investment structure, the ABC becomes the better alternative for energy utilisation. A preliminary economic evaluation shows that (at energy prices autumn 2000) the ABC is at the same level as the comparable small-scale cogeneration installations. Due to high power-to-heat ratio however, higher electricity prices will favour the ABC. One interesting feature of the ABC is that about 50% of the dissipated low-value heat from the cycle is carried by clean (sterile) air at the temperature around 200 deg C. This air can be utilised for space heating or

International double taxation

OpenAIRE

Körbl, Hugo

2012-01-01

1 Summary This thesis deals with the issue of international double taxation of income and capital and methods for its solution. International double taxation is an issue which states began to deal with in the late 19th century. This interest intensified after the First World War when also the League of Nations (predecessor of the United Nations) began to deal with international double taxation. Most attention the phenomenon of double taxation of income and capital with an international elemen...

An integrated top-down and bottom-up strategy for characterization protein isoforms and modifications

Energy Technology Data Exchange (ETDEWEB)

Wu, Si; Tolic, Nikola; Tian, Zhixin; Robinson, Errol W.; Pasa-Tolic, Ljiljana

2011-04-15

Bottom-up and top-down strategies are two commonly used methods for mass spectrometry (MS) based protein identification; each method has its own advantages and disadvantages. In this chapter, we describe an integrated top-down and bottom-up approach facilitated by concurrent liquid chromatography-mass spectrometry (LC-MS) analysis and fraction collection for comprehensive high-throughput intact protein profiling. The approach employs a high resolution reversed phase (RP) LC separation coupled with LC eluent fraction collection and concurrent on-line MS with a high field (12 Tesla) Fourier-transform ion cyclotron resonance (FTICR) mass spectrometer. Protein elusion profiles and tentative modified protein identification are made using detected intact protein mass in conjunction with bottom-up protein identifications from the enzymatic digestion and analysis of corresponding LC fractions. Specific proteins of biological interest are incorporated into a target ion list for subsequent off-line gas-phase fragmentation that uses an aliquot of the original collected LC fraction, an aliquot of which was also used for bottom-up analysis.

Formation of double layers

International Nuclear Information System (INIS)

Leung, P.; Wong, A.Y.; Quon, B.H.

1981-01-01

Experiments on both stationary and propagating double layers and a related analytical model are described. Stationary double layers were produced in a multiple plasma device, in which an electron drift current was present. An investigation of the plasma parameters for the stable double layer condition is described. The particle distribution in the stable double layer establishes a potential profile, which creates electron and ion beams that excite plasma instabilities. The measured characteristics of the instabilities are consistent with the existence of the double layer. Propagating double layers are formed when the initial electron drift current is large. Ths slopes of the transition region increase as they propagate. A physical model for the formation of a double layer in the experimental device is described. This model explains the formation of the low potential region on the basis of the space charge. This space charge is created by the electron drift current. The model also accounts for the role of ions in double layer formation and explains the formation of moving double layers. (Auth.)

Spectroscopy and lifetime of bottom and charm hadrons

International Nuclear Information System (INIS)

F. Ukegawa

2000-01-01

There are several motivations for studying masses and lifetimes of the hadrons containing a heavy quark, either the bottom or the charm quark. First, the mass and the lifetime are fundamental properties of an elementary particle. Second, the spectroscopy of hadrons gives insights into the QCD potential between quarks. In particular, a symmetry exists for heavy hadrons when the heavy quark mass is taken to be infinite, providing a powerful tool to predict and understand properties of those heavy hadrons. Third, studies of the lifetimes of heavy hadrons probe their decay mechanisms. A measurement of the lifetime, or the total decay width, is necessary when the authors extract magnitudes of elements of the Kobayashi-Maskawa matrix. Again, in the limit of an infinite heavy quark mass things become simple and decay of a heavy hadron should be the decay of the heavy quark Q. This leads to a prediction that all hadrons containing the heavy quark Q should have the same lifetime, that of the quark Q. This is far from reality in the case of charm hadrons, where the D + meson lifetime is about 2.5 times longer than the D 0 meson lifetime. Perhaps the charm quark is not heavy enough. The simple quark decay picture should be a better approximation for the bottom hadrons because of the larger b quark mass. On the experimental side, the measurements and knowledge of the heavy hadrons (in particular bottom hadrons) have significantly improved over the last decade, thanks to high statistics data accumulated by various experiments. The authors shall review recent developments in these studies in the remainder of this manuscript

Increased performance in a bottom-up designed robot by experimentally guided redesign

DEFF Research Database (Denmark)

Larsen, Jørgen Christian

2013-01-01

Purpose – Using a bottom-up, model-free approach when building robots is often seen as a less scientific way, compared to a top-down model-based approach, because the results are not easily generalizable to other systems. The authors, however, hypothesize that this problem may be addressed by using...... the bottom-up, mode-free approach, the authors used the robotic construction kit, LocoKit. This construction kit allows researchers to construct legged robots, without having a mathematical model beforehand. The authors used no specific mathematical model to design the robot, but instead used intuition...... solid experimental methods. The purpose of this paper is to show how well-known experimental methods from bio-mechanics are used to measure and locate weaknesses in a bottom-up, model-free implementation of a quadruped walker and come up with a better solution. Design/methodology/approach – To study...

Bottom and top physics

International Nuclear Information System (INIS)

Foley, K.J.; Gilman, F.J.; Herten, G.; Hinchliffe, I.; Jawahery, A.; Sanda, A.; Schmidt, M.P.; Schubert, K.R.; Fridman, A.

1988-01-01

The production of heavy quark flavors occurs primarily by the strong interactions and offers another arena in which to test QCD and to probe gluon distributions at very small values of x. Such quarks can also be produced as decay products of possible new, yet undiscovered particles, e.g., Higgs bosons, and therefore are a necessary key to reconstructing such particles. The decay products of heavy quarks, especially from their semileptonic decays, can themselves form a background to other new physics processes. The production of bottom quarks at the SSC and the formalism and phenomenology of observing CP violation in B meson decays is discussed. The production of a heavy t quark which decays into a real W boson, and what might be learned from its decays is examined

Some Durability Aspects of Ambient Cured Bottom Ash Geopolymer Concrete

Directory of Open Access Journals (Sweden)

Saravanakumar R.

2017-09-01

Full Text Available The present study examines some durability aspects of ambient cured bottom ash geopolymer concrete (BA GPC due to accelerated corrosion, sorptivity, and water absorption. The bottom ash geopolymer concrete was prepared with sodium based alkaline activators under ambient curing temperatures. The sodium hydroxide used concentration was 8M. The performance of BA GPC was compared with conventional concrete. The test results indicate that BA GPC developes a strong passive layer against chloride ion diffusion and provides better protection against corrosion. Both the initial and final rates of water absorption of BA GPC were about two times less than those of conventional concrete. The BA GPC significantly enhanced performance over equivalent grade conventional concrete (CC.

Valorization of MSWI bottom ash for biogas desulfurization: Influence of biogas water content.

Science.gov (United States)

Fontseré Obis, Marta; Germain, Patrick; Troesch, Olivier; Spillemaecker, Michel; Benbelkacem, Hassen

2017-02-01

In this study an alternative valorization of Municipal Solid Waste Incineration (MSWI) Bottom Ash (BA) for H 2 S elimination from landfill biogas was evaluated. Emphasis was given to the influence of water content in biogas on H 2 S removal efficiency by BA. A small-scale pilot was developed and implemented in a landfill site located in France. A new biogas analyzer was used and allowed real-time continuous measurement of CH 4 , CO 2 , O 2 , H 2 S and H 2 O in raw and treated biogas. The H 2 S removal efficiency of bottom ash was evaluated for different inlet biogas humidities: from 4 to 24g water /m 3 . The biogas water content was found to greatly affect bottom ash efficiency regarding H 2 S removal. With humid inlet biogas the H 2 S removal was almost 3 times higher than with a dry inlet biogas. Best removal capacity obtained was 56gH 2 S/kgdryBA. A humid inlet biogas allows to conserve the bottom ash moisture content for a maximum H 2 S retention. Copyright © 2016 Elsevier Ltd. All rights reserved.

Material distribution in treated MSWI bottom ash fractions

NARCIS (Netherlands)

van de Wouw, P.M.F.; Florea, M.V.A.; Brouwers, H.J.H.

2016-01-01

Municipal Solid Waste Incineration (MSWI) reduces the mass and volume of the waste by about 70% and 90%, respectively. Next to boiler and fly ash, solid MSWI Bottom Ash (BA) makes up for 80% of the remaining material and contains unburned matter, glass, ceramics, metals, and minerals. At present BA

Pressure drop performance evaluation for test assemblies with the newly developed top and bottom nozzles

International Nuclear Information System (INIS)

Lee, S. K.; Park, N. K.; Su, J. M.; Kim, H. K.; Lee, J. N.; Kim, K. T.

2003-01-01

To perform the hydraulic test for the newly developed top and bottom nozzles, two kinds of test assemblies were manufactured i. e. one is the test assembly which has the newly developed top and bottom nozzles and the other is Guardian test assembly which is commercially in mass production now. The test results show that the test assembly with one top nozzle and two bottom nozzles has a greater pressure loss coefficient than Guardian test assembly by 60.9% and 90.4% at the bottom nozzle location. This cause is due to the debris filtering plate for bottom nozzle to improve a filtering efficiency aginst foreign material. In the region of mid grid and top nozzle, there is no difference in pressure loss coefficient between the test assemblies since the componet features in these regions are very similar or same each other. The loss coefficients are 14.2% and 21.9% for model A and B respectively in the scale of test assembly, and the value would be within the 10% in the scale of real fuel assembly. As a result of hydraulic performance evaluation, model A is superior to model B

MSWI Bottom Ash Characterization and Resource Recovery Potential Assessment.

Czech Academy of Sciences Publication Activity Database

Šyc, Michal; Kameníková, Petra; Krausová, Aneta; Zach, Boleslav; Pohořelý, Michael; Svoboda, Karel; Punčochář, Miroslav

2015-01-01

Roč. 2, č. 36 (2015), s. 79-84 ISSN 1640-4902 R&D Projects: GA TA ČR TE02000236 Institutional support: RVO:67985858 Keywords : MSWI * bottom ash * metal recovery Subject RIV: CI - Industrial Chemistry, Chemical Engineering

MONITORING OF PHOSPHORUS CONTENT IN “WATER-PARTICULATE MATERIALS-BOTTOM SEDIMENTS SYSTEM” FOR RIVER PRUT

Directory of Open Access Journals (Sweden)

VASILE RUSU

2011-03-01

Full Text Available Monitoring of phosphorus content in “water-particulatematerials-bottom sediments system” for river Prut. Seasonal and spatialdynamics of phosphorus forms in water, particulate materials and bottomsediments of river Prut was elucidated. The scheme for determination ofphosphorus forms in water and particulate materials according to World HealthOrganization classification was evaluated. Additionally, this scheme was tested forestimation of phosphorus content in bottom sediments. The supplemented schemeallows the analysis of the phosphorus forms for the entirely system “water –particulate materials – bottom sediments”, extending possibilities for interpretationof phosphorus dynamics in natural waters.

A Bottom-up Approach to Environmental Cost-Benefit Analysis

DEFF Research Database (Denmark)

Carolus, Johannes Friedrich; Hanley, Nick; Olsen, Søren Bøye

with the underlying environmental problem, and then assesses costs and benefits of various strategies and solutions suggested by local and directly affected stakeholders. For empirical case studies concerning two river catchments in Sweden and Latvia, the bottom-up CBA approach utilises local knowledge, assesses......Cost-Benefit Analysis is a method to assess the effects of policies and projects on social welfare. CBAs are usually applied in a top-down approach, in the sense that a decision-making body first decides on which policies or projects are to be considered, and then applies a set of uniform criteria...... plans which are not only developed for local conditions but are also likely to be more acceptable to local society, and sheds additional light on possible distributional effects. By not only benefitting from, but also supporting participative environmental planning, bottom-up CBA is in line...

Experimental and simulation studies on a single pass, double duct solar air heater

Energy Technology Data Exchange (ETDEWEB)

Forson, F.K. [Kwame Nkrumah Univ. of Science and Technology, Dept. of Mechanical Engineering, Kumasi (Ghana); Rajakaruna, H. [De Montfort Univ., School of Engineering and Technology, Leicester (United Kingdom)

2003-05-01

A mathematical model of a single pass, double duct solar air heater (SPDDSAH) is described. The model provides a design tool capable of predicting: incident solar radiation, heat transfer coefficients, mean air flow rates, mean air temperature and relative humidity at the exit. Results from the simulation are presented and compared with experimental ones obtained on a full scale air heater and a small scale laboratory one. Reasonable agreement between the predicted and measured values is demonstrated. Predicted results from a parametric study are also presented. It is shown that significant improvement in the SPDDSAH performance can be obtained with an appropriate choice of the collector parameters and the top to bottom channel depth ratio of the two ducts. The air mass flow rate is shown to be the dominant factor in determining the overall efficiency of the heater. (Author)

Phosphorus availability from bottom sediments of lakes using a nuclear technique

International Nuclear Information System (INIS)

Flores, F.; Facetti, J.F.

1991-01-01

Availability of phosphorus from the bottom sediments of a lake plays an import role in the development of aquatic biota and in the enhancement of eutrophication process. In this work the 31 P↔ 32 P isotopic exchange (E values) technique was applied to assess the potential influence of this phosphorus reservoir on the water quality of Acaray and Yguazu Dams, at the Eastern Region of Paraguay. Samples analyzed were taken from the bottom sediments of the water bodies at different sites as well as from the shores. The method is reliable and yields information of ecological significance

Pemanfaatan Bottom Ash Sebagai Agregat Buatan

OpenAIRE

Nuciferani, Felicia Tria; Antoni, Antoni; Hardjito, Djwantoro

2014-01-01

The aim of this study is to explore the possible use of bottom ash as artificial aggregates. It is found that the pelletizer method by using mixer without blade is one possibility to manufacture artificial aggregates. The optimum mixture composition of artificial aggregate is found to be 3 BA : 1FA : 0,5 C , by weight, and immersed once in cement slurry. The water content in ssd condition is 27% with the compressive strength of the aggregate 2.4 MPa on the seventh day. Concrete produced with ...

High-frequency bottom-pressure and acoustic variations in a sea strait: internal wave turbulence

NARCIS (Netherlands)

van Haren, H.

2012-01-01

During a period of 3 days, an accurate bottom-pressure sensor and a four-beam acoustic Doppler current profiler (ADCP) were mounted in a bottom frame at 23 m in a narrow sea strait with dominant near-rectilinear tidal currents exceeding 1 m s(-1) in magnitude. The pressure record distinguishes small

Bottom Dissolved Oxygen Maps From SEAMAP Summer Groundfish/Shrimp Surveys

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Bottom dissolved oxygen (DO) data was extracted from environmental profiles acquired during the Southeast Fisheries Science Center Mississippi Laboratories summer...

Monitoring changes in stream bottom sediments and benthic invertebrates.

Science.gov (United States)

1981-01-01

The study was conducted to determine whether the analysis of stream bottom sediments could be used to assess sediment pollution generated by highway construction. Most of the work completed to date has involved testing and refining methods for the co...

Microbial quality of bagged baby spinach and romaine lettuce: effects of top versus bottom sampling.

Science.gov (United States)

Kase, Julie A; Borenstein, Stacey; Blodgett, Robert J; Feng, Peter C H

2012-01-01

Contamination with Escherichia coli O157:H7 and Salmonella have called into question the safety and microbial quality of bagged ready-to-eat leafy greens. This study expands on previous findings that these goods have high total bacteria counts (TBC) and coliform counts, variation in counts among different lots, that Escherichia coli is present, and disparities in counts when bags are top or bottom sampled. Nearly 100 bags of baby spinach and hearts of romaine lettuce from a single brand were subjected to both top and bottom sampling. Product was blended, and a portion serially diluted and plated to obtain TBC. Total coliform and E. coli levels were estimated by the most-probable-number (MPN) technique with ColiComplete discs. Top-sampled TBC from bags of baby spinach (48 bags, 13 different lots) ranged from 3.9 to 8.1 log CFU/g and bottom-sampled TBC ranged from 4.0 to 8.2 log CFU/g, with 52% of the bags (or 39% of the lots) producing TBC higher in bottom samples. For hearts of romaine (47 bags from 19 different lots), top-sampled bags had TBC ranging from 2.4 to 7.0 log, and bottom-sampled bags had TBC from 3.3 to 7.3 log, with 64% of the bags (or 63% of the lots) showing higher TBC in bottom samples. However, we are unable to reject the hypothesis that the top and bottom samples from either commodity contain the same TBC (P ≥ 0.08). No E. coli was detected and total coliform bacteria counts were, with few exceptions, ≥210 MPN/g, irrespective of TBC. In general, lots with the most number of days before the printed "use-by" date had lower TBC. However, the R(2) values for either baby spinach (0.4085) or hearts of romaine (0.2946) suggest that age might not be a very good predictor of higher TBC. TBC varied widely between lots and even more so within same-lot samples, as indicated by the sum of squares results. This finding, along with higher TBC in bottom samples, suggests further consideration when a microbiological sampling scheme of bagged produce is

Air bottoming cycle, an alternative to combined cycles. Final report

Energy Technology Data Exchange (ETDEWEB)

Kaikko, J. [Royal Inst. of Tech., Stockholm (Sweden). Dept. of Energy Technology

2002-02-01

In this work, the idea of Air Bottoming Cycle (ABC) has been studied. The objectives for the work have been to establish an understanding of the concept for power and heat generation as well as to find - if possible - feasible concepts for future use in the Swedish energy system. Combined cycle in power generation is an established technology. In the conventional combined cycle, a gas turbine works as a topping cycle together with the steam (Rankine) bottoming cycle. In the ABC the steam bottoming cycle is replaced with a gas turbine (Brayton) bottoming cycle having air as a working fluid. The two gas turbines are thermally connected over a gas-to-gas heat exchanger. This concept promises savings in weight and cost, as well as operating benefits, compared to the Rankine bottoming technology. The ABC has been modelled using a heat balance program, and a parametric study for the concept optimisation as well as for off-design analysis has been performed. Performance of the ABC has been compared to other, established technologies. A preliminary economic evaluation has been made. As a result of the study, it is clarified that the Rankine bottoming cycle with steam remains superior to the ABC as regards electrical efficiency in the medium and large power scale. For small-scale applications (<10 MW{sub e}) where the thermodynamic advantage of the Rankine cycle is not dominating any longer and its economy is burdened by the heavy investment structure, the ABC becomes the better alternative for energy utilisation. A preliminary economic evaluation shows that (at energy prices autumn 2000) the ABC is at the same level as the comparable small-scale cogeneration installations. Due to high power-to-heat ratio however, higher electricity prices will favour the ABC. One interesting feature of the ABC is that about 50% of the dissipated low-value heat from the cycle is carried by clean (sterile) air at the temperature around 200 deg C. This air can be utilised for space heating or

Bottom sample taker

Energy Technology Data Exchange (ETDEWEB)

Garbarenko, O V; Slonimskiy, L D

1982-01-01

In order to improve the quality of the samples taken during offshore exploration from benthic sediments, the proposed design of the sample taker has a device which makes it possible to regulate the depth of submersion of the core lifter. For this purpose the upper part of the core lifter has an inner delimiting ring, and within the core lifter there is a piston suspended on a cable. The position of the piston in relation to the core lifter is previously assigned depending on the compactness of the benthic sediments and is fixed by tension of the cable which is held by a clamp in the cover of the core taker housing. When lowered to the bottom, the core taker is released, and under the influence of hydrostatic pressure of sea water, it enters the sediments. The magnitude of penetration is limited by the distance between the piston and the stopping ring. The piston also guarantees better preservation of the sample when the instrument is lifted to the surface.

Numerical simulation of water flow through the bottom en piece of a nuclear fuel assembly

International Nuclear Information System (INIS)

Navarro, Moyses A.; Santos, Andre A. Campagnole dos

2007-01-01

The water flow through the bottom nozzle of a nuclear fuel assembly was simulated using a commercial CFD code, CFX 10.0. Previously, simulations with a perforated plate similar to the bottom nozzle plate were performed to define the appropriate mesh refinement and turbulence model (κ-ε or SST). Subsequently, the numerical simulation was performed with the optimized mesh using the turbulence model (κ-ε in a standard bottom nozzle with some geometric simplifications. The numerical results were compared with experimental results to determine the pressure drop through the bottom nozzle in the Reynolds range from ∼10500 to ∼95000. The agreement between the numerical simulations and experimental results may be considered satisfactory. The study indicated that the CFD codes can play an important role in the development of pieces with complex geometries, optimizing the planning of the experiments and aiding in the experimental analysis. (author)

A dataset from bottom trawl survey around Taiwan

Directory of Open Access Journals (Sweden)

Kwang-tsao Shao

2012-05-01

Full Text Available Bottom trawl fishery is one of the most important coastal fisheries in Taiwan both in production and economic values. However, its annual production started to decline due to overfishing since the 1980s. Its bycatch problem also damages the fishery resource seriously. Thus, the government banned the bottom fishery within 3 nautical miles along the shoreline in 1989. To evaluate the effectiveness of this policy, a four year survey was conducted from 2000–2003, in the waters around Taiwan and Penghu (Pescadore Islands, one region each year respectively. All fish specimens collected from trawling were brought back to lab for identification, individual number count and body weight measurement. These raw data have been integrated and established in Taiwan Fish Database (http://fishdb.sinica.edu.tw. They have also been published through TaiBIF (http://taibif.tw, FishBase and GBIF (website see below. This dataset contains 631 fish species and 3,529 records, making it the most complete demersal fish fauna and their temporal and spatial distributional data on the soft marine habitat in Taiwan.

Bottom-mounted control rod drive mechanism for KJRR

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin Haeng; Kim, Sanghaun; Yoo, Yeon-Sik, E-mail: yooys@kaeri.re.kr; Cho, Yeong-Garp; Huh, Hyung; Lee, Hyokwang; Sun, Jong-Oh; Ryu, Jeong-Soo

2016-04-15

Highlights: • The basic design features and characteristics of the KJRR BMCRDM are described. • The similarities and differences of some research reactor CRDMs are compared. • The current status of the design and development of the CRDM is described. • The future plan of the qualification tests of the CRDM is summarized. - Abstract: The KIJANG research reactor (KJRR), which is currently being designed by Korea Atomic Energy Research Institute, is a pool type research reactor with 15 MW of thermal power. Contrary to the top-mounted control rod drive mechanism (CRDM), the main drive mechanism of the KJRR CRDM is located in a reactivity control mechanism room under the reactor pool bottom. Recently, we accomplished the design and development of a prototype CRDM. In this paper, we introduce the basic design concept of the bottom-mounted CRDM for KJRR, and compare the similarities and differences of some research reactor CRDMs. The current status of the prototype CRDM development based on a finite element analysis and experimental verification, and the future plan of the CRDM qualification tests, are both described.

Bioassay of Lake Onego bottom sediments toxicity based on their chemical composition and deepwater macrozoobenthos state

Directory of Open Access Journals (Sweden)

Kalinkina Nataliya Michailovna

2017-03-01

Full Text Available The bioassay of the toxicity of bottom sediments sampled in different areas of Lake Onega was carried out by crustaceans biotesting (Ceriodaphnia affinis Lillijeborg. It was shown that in the most areas of Lake Onega there are non-toxic bottom sediments. Toxic bottom sediments were found in Kondopogskaya Bay, intensively polluted with pulp-and-paper mill wastewaters. For the first time in the deep central part of Lake Onega the area was revealed where the toxic bottom sediments contain a high content of iron, manganese and other trace elements typical for the central areas of the lake. The mapping of the bottom of Lake Onega was accomplished, and three zones were identified based on the analysis of the data concerning the chemical composition of bottom sediments, bioassay toxicity data and the results of the deepwater macrozoobenthos assessment. For each zone the parameters of the main groups of benthos (Amphipoda, Oligochaeta, Chironomidae were defined. The first zone is located in the area of intensive anthropogenic influence (Kondopogskaya Bay, Petrozavodskaya Bay, Povenets Bay, Kizhi Skerries. The second zone is located mostly in the deep part of Petrozavodskaya Bay, where the most intensive development of amphipods is observed. The third area is identified for the first time: it is located in the central deep part of Lake Onega, where the communities of macrozoobenthos are limited by a natural toxic factor.

Double Trouble

NARCIS (Netherlands)

Elsaesser, Thomas; Kievit, Robert; Simons, Jan

1994-01-01

Double Trouble highlights the career of Dutch scriptwriter and television producer Chiem van Houweninge, well-known for his long-running TV comedy series and as author of episodes for TV detective series. Double Trouble gives Van Houweninge's own views on writing and filming in television prime

Hydrodynamic cavitation: a bottom-up approach to liquid aeration

NARCIS (Netherlands)

Raut, J.S.; Stoyanov, S.D.; Duggal, C.; Pelan, E.G.; Arnaudov, L.N.; Naik, V.M.

2012-01-01

We report the use of hydrodynamic cavitation as a novel, bottom-up method for continuous creation of foams comprising of air microbubbles in aqueous systems containing surface active ingredients, like proteins or particles. The hydrodynamic cavitation was created using a converging-diverging nozzle.

Dual-frequency ring-magnet power supply with flat bottom

International Nuclear Information System (INIS)

Praeg, W.F.

1983-01-01

A power supply is described that furnishes an essentially flat-bottom injection field, followed by a dual-frequency cosine field. This results in efficient beam capture during injection and reduces significantly the peak rf power required during acceleration in a rapid-cycling synchrotron

Bottom loaded filter for radioactive liquids

International Nuclear Information System (INIS)

Wendland, W.G.

1983-01-01

This invention relates to equipment for filtering liquids and more particularly to filter assemblies for use with radioactive by-products of nuclear power plants. The invention provides a compact, bottom-loaded filter assembly that can be quickly and safely loaded and unloaded without the use of complex remote equipment. The assembly is integrally shielded and does not require external shielding. The closure hatch may be automatically aligned to facilitate quick sealing attachment after replacement of the filter cartridge, and the filter cartridge may be automatically positioned within the filter housing during the replacement operation

Recognition and Construction of Top, Bottom, and Versatile Orientations in Gay/Bisexual Men.

Science.gov (United States)

Moskowitz, David A; Roloff, Michael E

2017-01-01

Research on gay and bisexual men's sexual position self-label (i.e., being a top, bottom, or versatile during anal sex) has revealed only independent snapshots of its development by focusing primarily on the influence of penis size. Moreover, the basic chronology of development of the sexual position self-label has barely been addressed. In response, we implemented a survey of 282 gay and bisexual men that measured demographics (including height and penis size), age of sexual recognitions, sexual position self-label, and attitudinal constructs suggested by previous literature as important (e.g., pleasure, control, anxieties, and gender typicality). Results suggested that men's sexual position self-label was learned over a 15-year timespan. Ages of first same-sex genital manipulation and first anal sex experiences were related to age at first self-labeling. With respect to predictors of labels, a multivariate path model was created. The model did not support the direct importance of penis size, but identified indirect paths that linked penis size to top/bottom identification (e.g., smaller penis sizes leading to topping-anxieties and thus, a bottom label). Finding bottoming to be pleasurable and the importance of sexual control dynamics were the only two direct predictors. The path model substantiated the reliance both bottoms and tops show towards seeking (or not seeking among tops) gender typical, sexually dominant partners. It also supported previous evidence regarding race; specifically, while race may activate differences in sexual behavioral dynamics, it is not a great predictor of the sexual position self-label. This study shows that sexual position self-labeling has enormous complexity and cannot be reduced down to penis size.

A Comprehensive Review on the Properties of Coal Bottom Ash in Concrete as Sound Absorption Material

OpenAIRE

Ramzi Hannan Nurul Izzati Raihan; Shahidan Shahiron; Ali Noorwirdawati; Maarof Mohamad Zulkhairi

2017-01-01

The government is currently implementing policies to increase the usage of coal as fuel for electricity generation. At the same time, the dependency on gas will be reduced. In addition, coal power plants in Malaysia produce large amounts of industrial waste such as bottom ash which is collected in impoundment ponds (ash pond). However, millions of tons of coal ash (bottom ash) waste are collected in ponds near power plant stations. Since bottom ash has been classified as hazardous material th...

Effects of the bottom boundary condition in numerical investigations of dense water cascading on a slope

Science.gov (United States)

Berntsen, Jarle; Alendal, Guttorm; Avlesen, Helge; Thiem, Øyvind

2018-05-01

The flow of dense water along continental slopes is considered. There is a large literature on the topic based on observations and laboratory experiments. In addition, there are many analytical and numerical studies of dense water flows. In particular, there is a sequence of numerical investigations using the dynamics of overflow mixing and entrainment (DOME) setup. In these papers, the sensitivity of the solutions to numerical parameters such as grid size and numerical viscosity coefficients and to the choices of methods and models is investigated. In earlier DOME studies, three different bottom boundary conditions and a range of vertical grid sizes are applied. In other parts of the literature on numerical studies of oceanic gravity currents, there are statements that appear to contradict choices made on bottom boundary conditions in some of the DOME papers. In the present study, we therefore address the effects of the bottom boundary condition and vertical resolution in numerical investigations of dense water cascading on a slope. The main finding of the present paper is that it is feasible to capture the bottom Ekman layer dynamics adequately and cost efficiently by using a terrain-following model system using a quadratic drag law with a drag coefficient computed to give near-bottom velocity profiles in agreement with the logarithmic law of the wall. Many studies of dense water flows are performed with a quadratic bottom drag law and a constant drag coefficient. It is shown that when using this bottom boundary condition, Ekman drainage will not be adequately represented. In other studies of gravity flow, a no-slip bottom boundary condition is applied. With no-slip and a very fine resolution near the seabed, the solutions are essentially equal to the solutions obtained with a quadratic drag law and a drag coefficient computed to produce velocity profiles matching the logarithmic law of the wall. However, with coarser resolution near the seabed, there may be a

Enhanced E-bed bottoms upgrading using latest catalytic technology

Energy Technology Data Exchange (ETDEWEB)

Toshima, H.; Mayo, S.; Sedlacek, Z.; Hughes, T.; De Wind, M. [Albermarle Corp., Amsterdam (Netherlands)

2009-07-01

The profitability of refineries depends on heavy oil upgrading in terms of price, conversion, yields and quality of the product. The Ebullated-bed process represents a solution for the effective primary upgrading of heavy oils. Since the 1970s, Albemarle has commercialized several E-bed catalysts to upgrade the bottoms in low sediment and high hydrogenation operations. Although an E-bed is used to maximize the conversion of vacuum residuum (VR), it is often limited by fouling caused by sediment in the product. In order to reduce sedimentation in the product, Albemarle developed an improved E-bed catalytic technology by characterizing the asphaltenes and sediments in order to better understand the oil chemistry and compatibility. The most recent development involves the patented catalyst-staging technology and the improved single catalyst application. Both achieve very low sediment or higher hydrodesulphurization (HDS) and Conradson carbon (CCR) removal for improved bottom upgrading. tabs., figs.

Bottom up design of nanoparticles for anti-cancer diapeutics

DEFF Research Database (Denmark)

Needham, David; Arslanagic, Amina; Glud, Kasper

2016-01-01

for EPR uptake and tumor detection. We show that, while free-drug cannot be optimally administered in vivo, a nanoparticle formulation of orlistat could in principle represent a stable parenteral delivery system. The article ends with a brief discussion of what we see as the way forward in Individualized...... the feasibility of an idea: could we design, make, develop, and test the concept for treating metastatic cancer by, "Putting the Drug in the Cancer's Food? "Limit size" is the size of the cancer's food, ? the common Low Density Lipoprotein, (LDL) ~20 nm diameter. In this contribution to Pieter's LTAA we focus...... on the "bottom" (nucleation) and the "up" (growth) of "bottom-up design" as it applies to homogeneous nucleation of especially, hydrophobic drugs and the 8 physico-chemical stages and associated parameters that determine the initial size, and any subsequent coarsening, of a nanoparticle suspension. We show that...

Final summary report on the Peach Bottom End-of-Life Program

International Nuclear Information System (INIS)

Steward, K.P.

1978-07-01

HTGR design methods verifications have been performed under the Peach Bottom End-of-Life Program by comparison of actual with predicted physics, thermal, fission product, and materials behavior in Peach Bottom. These design methods verifications have utilized the data determined from nondestructive fuel and circuit gamma scanning on-site, from laboratory examinations of samples removed from the primary circuit, and from a complementary program of Peach Bottom fuel element postirradiation examinations at Oak Ridge National Laboratory. Fifty-five driver fuel elements were axially gamma scanned to determine fission product distributions for use in burnup calculations, power profile determinations, and fission product release and redistribution studies. The cesium plateout distribution in the primary circuit was subsequently mapped by gamma scanning the ducting at 12 locations, axially traversing 79 steam generator tubes with Cd Te detectors from the water side, and internally scanning two vertical runs of ducting. Component removal involved trepanning of the primary circuit ducting, obtaining access to the steam generator internals, and removing over 100 superheater, evaporator, and economizer tubing samples. During this phase, macroscopic examinations of the steam generator and ducting internals were performed. Subsequent laboratory examinations of removed samples included radiochemical tests to substantiate in-situ gamma scans and to determine 90 Sr distributions; metallurgical tests to evaluate surface films, microstructural changes, and residual mechanical properties; and tritium permeation tests to provide data for improving HTGR tritium release predictions. The condition and metallurgical integrity of all components examined were found to be excellent, with minimal coolant/substrate interaction and entirely acceptable residual mechanical properties. The suitability of the materials used in the construction of the Peach Bottom HTGR was thereby confirmed

Utilization of sepiolite materials as a bottom liner material in solid waste landfills.

Science.gov (United States)

Guney, Yucel; Cetin, Bora; Aydilek, Ahmet H; Tanyu, Burak F; Koparal, Savas

2014-01-01

Landfill bottom liners are generally constructed with natural clay soils due to their high strength and low hydraulic conductivity characteristics. However, in recent years it is increasingly difficult to find locally available clay soils that satisfy the required engineering properties. Fine grained soils such as sepiolite and zeolite may be used as alternative materials in the constructions of landfill bottom liners. A study was conducted to investigate the feasibility of using natural clay rich in kaolinite, sepiolite, zeolite, and their mixtures as a bottom liner material. Unconfined compression tests, swell tests, hydraulic conductivity tests, batch and column adsorption tests were performed on each type of soil and sepiolite-zeolite mixtures. The results of the current study indicate that sepiolite is the dominant material that affects both the geomechanical and geoenvironmental properties of these alternative liners. An increase in sepiolite content in the sepiolite-zeolite mixtures increased the strength, swelling potential and metal adsorption capacities of the soil mixtures. Moreover, hydraulic conductivity of the mixtures decreased significantly with the addition of sepiolite. The utilization of sepiolite-zeolite materials as a bottom liner material allowed for thinner liners with some reduction in construction costs compared to use of a kaolinite-rich clay. Copyright © 2013 Elsevier Ltd. All rights reserved.

Collection and preparation of bottom sediment samples for analysis of radionuclides and trace elements

International Nuclear Information System (INIS)

2003-07-01

The publication is the first in a series of TECDOCs on sampling and sample handling as part of the IAEA support to improve reliability of nuclear analytical techniques (NATs) in Member State laboratories. The purpose of the document is to provide information on the methods for collecting sediments, the equipment used, and the sample preparation techniques for radionuclide and elemental analysis. The most appropriate procedures for defining the strategies and criteria for selecting sampling locations, for sample storage and transportation are also given. Elements of QA/QC and documentation needs for sampling and sediment analysis are discussed. Collection and preparation of stream and river bottom sediments, lake bottom sediments, estuary bottom sediments, and marine (shallow) bottom sediments are covered. The document is intended to be a comprehensive manual for the collection and preparation of bottom sediments as a prerequisite to obtain representative and meaningful results using NATs. Quality assurance and quality control (QA/QC) is emphasized as an important aspect to ensure proper collection, transportation, preservation, and analysis since it forms the basis for interpretation and legislation. Although there are many approaches and methods available for sediment analyses, the scope of the report is limited to sample preparation for (1) analysis of radionuclides (including sediment dating using radionuclides such as Pb-210 and Cs-137) and (2) analysis of trace, minor and major elements using nuclear and related analytical techniques such as NAA, XRF and PIXE

Collection and preparation of bottom sediment samples for analysis of radionuclides and trace elements

Energy Technology Data Exchange (ETDEWEB)

NONE

2003-07-01

The publication is the first in a series of TECDOCs on sampling and sample handling as part of the IAEA support to improve reliability of nuclear analytical techniques (NATs) in Member State laboratories. The purpose of the document is to provide information on the methods for collecting sediments, the equipment used, and the sample preparation techniques for radionuclide and elemental analysis. The most appropriate procedures for defining the strategies and criteria for selecting sampling locations, for sample storage and transportation are also given. Elements of QA/QC and documentation needs for sampling and sediment analysis are discussed. Collection and preparation of stream and river bottom sediments, lake bottom sediments, estuary bottom sediments, and marine (shallow) bottom sediments are covered. The document is intended to be a comprehensive manual for the collection and preparation of bottom sediments as a prerequisite to obtain representative and meaningful results using NATs. Quality assurance and quality control (QA/QC) is emphasized as an important aspect to ensure proper collection, transportation, preservation, and analysis since it forms the basis for interpretation and legislation. Although there are many approaches and methods available for sediment analyses, the scope of the report is limited to sample preparation for (1) analysis of radionuclides (including sediment dating using radionuclides such as Pb-210 and Cs-137) and (2) analysis of trace, minor and major elements using nuclear and related analytical techniques such as NAA, XRF and PIXE.

The Plastic Potential, Double-slip, Double-spin and Viscoplasticity

Science.gov (United States)

Harris, David

2010-05-01

In this paper we describe two classical models for rate-independent behaviour of granular materials, namely the plastic potential and the double shearing model, emphasising their ill-posedness. We then describe a model, called the doubleslip and double-spin model which generalises the plastic potential model and is closely related to the double shearing model. This new model eliminates the causes of the ill-posedness in the classical models and provides a suitable basis for the analysis of the deformation and flow of granular materials in the rate-independent regime. There has been considerable recent interest in the intermediate regime between densely-packed, rate-independent, quasistatic flow and the rate-dependent dilute gaseous regime. In this intermediate regime the material also exhibits a degree of ratedependence. The natural extension of a rate-independent plasticity model to incorporate rate-dependent material behaviour is by way of viscoplasticity. The archetypal example here is the Bingham material which generalises a von Mises type plasticity model and introduces a viscosity parameter into the model. We propose an extension of the double-slip and double-spin model to incorporate viscosity, thereby extending the range of the model to incorporate rate-dependent behaviour. The new model is then applied to a simplified problem of pipe flow.

t anti tb anti b hadroproduction with massive bottom quarks with PowHel

International Nuclear Information System (INIS)

Bevilacqua, G.; Garzelli, M.V.; Kardos, A.

2017-09-01

The associated production of top-antitop-bottom-antibottom quarks is a relevant irreducible background for Higgs boson analyses in the top-antitop-Higgs production channel, with Higgs decaying into a bottom-antibottom quark pair. We implement this process in the PowHel event generator, considering the bottom quarks as massive in all steps of the computation which involves hard-scattering matrix-elements in the 4-flavour number scheme combined with 4-flavour Parton Distribution Functions. Predictions with NLO QCD+Parton Shower accuracy, as obtained by PowHel+PYTHIA, are compared to those which resulted from a previous PowHel implementation with hard-scattering matrix-elements in the 5-flavour number scheme, considering as a baseline the example of a realistic analysis of top-antitop hadroproduction with additional b-jet activity, performed by the CMS collaboration at the Large Hadron Collider.

Particles of bottom and suspended sediments: height of rise

Directory of Open Access Journals (Sweden)

Khodzinskaya Anna Gennadievna

2014-12-01

Full Text Available In the article, characteristic values of dynamic sizes of bottom and suspended sediments, including their probabilistic assessment, are considered. The article presents the processing results in respect of the experimental data for bottom and suspended sediments, obtained in the laboratory environment using samples and filming methods. The experiments have proven that the dynamic hydraulic size determines the height of rise for the particles of the saltation load, rather than suspended ones. In the laboratory environment, the maximal height of rise is mainly driven by the relative flow depth. According to the assessment made by the co-authors, depths of flows employed in the experiments designated for the identification of heights of rises, were comparable to saltation heights of particles. Besides, the saltation height of particles, having relative density well below 2.65, nearly always exceeded half of the depth of the laboratory flow. Hydrodynamic conditions favourable for the separation and motion of artificial particles in coarse surface tanks are far different from the motion of sand particles on the bottom of lowland rivers. Values of hydraulic resistance ratios typical for laboratory experiments by far exceed their values typical for lowland rivers, and it means that the conditions of the experiments performed in the laboratory were similar to those typical for mountain rivers. The research findings have proven that the particle separation and motion pattern, if artificial particles are made of the materials demonstrating variable density and elasticity values and if loose particles travel over fixed ones, is different from the pattern typical for natural particles having variable coarseness.

Modelling and Measurements of Bunch Profiles at the LHC Flat Bottom

CERN Document Server

Papadopoulou, Stefania; Muller, Juan; Papaphilippou, Yannis; Trad, Georges

2016-01-01

At the LHC flat bottom the interplay between a series of effects (i.e. intrabeam scattering, longitudinal beam manipulations, non-linearities of the machine, etc) can lead to a population of the tails of the beam distributions, which may become non-Gaussian. This paper presents observations of the evolution of particle distributions in the LHC flat bottom. Novel distribution functions are employed to represent the beam profiles, and used as a guideline for generalising emittance growth rate estimations due to IBS. Finally, an attempt is made to benchmark an IBS Monte-Carlo simulation code, able to track 3D particle distributions, with the measured beam profile evolutions.

Phosphorus availability from bottom sediments of lakes using a nuclear technique

International Nuclear Information System (INIS)

Flores, F.; Facetti, J.F.

1992-01-01

Availability of phosphorus from the bottom sediments of a lake plays an import role in the development of aquatic biota and in the enhancement of the eutrophication process. In this work, the 31 P- 32 P isotopic exchange (E values) technique was applied to assess the potential influence of this phosphorus 'reservoir' on the water quality of the Acaray and Yguazu Dams in the Easter Region of Paraguay. Samples analyzed were taken from the bottom sediments of the water body at different sites as well as from the shores. The method is reliable and yields information of potential ecological significance. (author) 14 refs.; 2 tabs

Application of thermally activated municipal solid waste incineration (MSWI) bottom ash fines as binder substitute

NARCIS (Netherlands)

Tang, P.; Florea, M.V.A.; Spiesz, P.R.; Brouwers, H.J.H.

Untreated municipal solid waste incineration (MSWI) bottom ash fines (0–2 mm) have poor pozzolanic properties, and contain substances which can pose an environmental risk (e.g. heavy metals and salts). This study investigates combined treatments applied on bottom ash fines (BAF) to increase their

Double layers in space

International Nuclear Information System (INIS)

Carlqvist, P.

1982-07-01

For more than a decade it has been realised that electrostatic double layers are likely to occur in space. We briefly discuss the theoretical background of such double layers. Most of the paper is devoted to an account of the observational evidence for double layers in the ionosphere and magnetosphere of the Earth. Several different experiments are reviewed including rocket and satellite measurements and ground based observations. It is concluded that the observational evidence for double layers in space is very strong. The experimental results indicate that double layers with widely different properties may exist in space. (Author)

Double layers in space

International Nuclear Information System (INIS)

Carlqvist, P.

1982-01-01

For more than a decade it has been realised that electrostatic double layers are likely to occur in space. The author briefly discusses the theoretical background of such double layers. Most of the paper is devoted to an account of the observational evidence for double layers in the ionosphere and magnetosphere of the Earth. Several different experiments are reviewed including rocket and satellite measurements and ground based observations. It is concluded that the observational evidence for double layers in space is very strong. The experimental results indicate that double layers with widely different properties may exist in space. (Auth.)

Fracture Mechanics Models for Brittle Failure of Bottom Rails due to Uplift in Timber Frame Shear Walls

Directory of Open Access Journals (Sweden)

Joergen L. Jensen

2016-01-01

Full Text Available In partially anchored timber frame shear walls, hold-down devices are not provided; hence the uplift forces are transferred by the fasteners of the sheathing-to-framing joints into the bottom rail and via anchor bolts from the bottom rail into the foundation. Since the force in the anchor bolts and the sheathing-to-framing joints do not act in the same vertical plane, the bottom rail is subjected to tensile stresses perpendicular to the grain and splitting of the bottom rail may occur. This paper presents simple analytical models based on fracture mechanics for the analysis of such bottom rails. An existing model is reviewed and several alternative models are derived and compared qualitatively and with experimental data. It is concluded that several of the fracture mechanics models lead to failure load predictions which seem in sufficiently good agreement with the experimental results to justify their application in practical design.

Persistent and energetic bottom-trapped topographic Rossby waves observed in the southern South China Sea

Science.gov (United States)

Shu, Yeqiang; Xue, Huijie; Wang, Dongxiao; Chai, Fei; Xie, Qiang; Cai, Shuqun; Chen, Rongyu; Chen, Ju; Li, Jian; He, Yunkai

2016-01-01

Energetic fluctuations with periods of 9–14 days below a depth of 1400 m were observed in the southern South China Sea (SCS) from 5 years of direct measurements. We interpreted such fluctuations as topographic Rossby waves (TRWs) because they obey the dispersion relation. The TRWs persisted from May 24, 2009 to August 23, 2013, and their bottom current speed with a maximum of ~10 cm/s was one order of magnitude greater than the mean current and comparable to the tidal currents near the bottom. The bottom-trapped TRWs had an approximate trapping depth of 325 m and reference wavelength of ~82 km, which were likely excited by eddies above. Upper layer current speed that peaked approximately every 2 months could offer the energy sources for the persistent TRWs in the southern SCS. Energetic bottom-trapped TRWs may have a comparable role in deep circulation to tides in areas with complex topography. PMID:27075644

Leaching behaviour of municipal solid waste incineration bottom ash: From granular material to monolithic concrete.

Science.gov (United States)

Sorlini, Sabrina; Collivignarelli, Maria Cristina; Abbà, Alessandro

2017-09-01

The aim of this work was to assess the leaching behaviour of the bottom ash derived from municipal solid waste incineration (MSWI) used in concrete production. In particular, the release of pollutants was evaluated by the application of different leaching tests, both on granular materials and monolithic samples (concrete mixtures cast with bottom ash). The results confirmed that, according to Italian regulations, unwashed bottom ashes present critical issues for the use as alternative aggregates in the construction sector due to the excessive release of pollutants; instead, the leachate from washed bottom ashes was similar to natural aggregates. The concentration of pollutants in the leachate from concrete mixtures was lower than regulation limits for reuse. The crushing process significantly influenced the release of pollutants: this behaviour was due both to the increase in surface area and the release of contaminants from cement. Moreover, the increase in contact time (up to 64 days) involved more heavy metals to be released.

A Bottom-up Trend in Research of Management of Technology

Directory of Open Access Journals (Sweden)

Yoko Ishino

2014-12-01

Full Text Available Management of Technology (MOT is defined as an academic discipline of management that enables organizations to manage their technological fundamentals to create competitive advantage. MOT covers a wide range of contents including administrative strategy, R&D management, manufacturing management, technology transfer, production control, marketing, accounting, finance, business ethics, and others. For each topic, researchers have conducted their MOT research at various levels. However, a practical and pragmatic side of MOT surely affects its research trends. Finding changes of MOT research trends, or the chronological transitions of principal subjects, can help understand the key concepts of current MOT. This paper studied a bottom-up trend in research fields in MOT by applying a text-mining method to the conference proceedings of IAMOT (International Association for Management of Technology. First, focusing on only nouns found several keywords, which more frequently emerge over time in the IAMOT proceedings. Then, expanding the scope into other parts of speech viewed the keywords in a natural context. Finally, it was found that the use of an important keyword has qualitatively and quantitatively extended over time. In conclusion, a bottom-up trend in MOT research was detected and the effects of the social situation on the trend were discussed.Keywords: Management of Technology; Text Mining; Research Trend; Bottom-up Trend; Patent

Double-continuum wave functions and double-photoionization cross sections of two-electron systems

International Nuclear Information System (INIS)

Tiwary, S.N.

1996-09-01

The present review briefly presents the growing experimental as well as theoretical interests in recent years in the double-continuum wave functions and double-photoionization cross sections of two-electron systems. The validity of existing double-continuum wave functions is analyzed and the importance of electronic correlations in both the initial as well as final states wave functions involved in the transition amplitude for double-photoionization process is demonstrated. At present, we do not have comprehensive and practical double-continuum wave functions which account the full correlation of two-electron in the continuum. Basic difficulties in making accurate theoretical calculations of double ionization by a single high energy photon especially in the vicinity of the threshold, where the correlation plays an important role, are discussed. Illuminating, illustrative and representative examples are presented in order to show the present status and the progress in this field. Future challenges and directions, in high-precision double-photoionization cross sections calculations, have been discussed and suggested. (author). 133 refs, 9 figs

Three-Dimensional Adjustment of Stratified Flow Over a Sloping Bottom

National Research Council Canada - National Science Library

Chapman, David

2002-01-01

.... Results indicate the simple theories are relevant to the ocean and that the bottom boundary layer plays an important role in the behavior of ocean currents, even when the boundary layer is thin...

Nanosecond laser scribing of CIGS thin film solar cell based on ITO bottom contact

Science.gov (United States)

Kuk, Seungkuk; Wang, Zhen; Fu, Shi; Zhang, Tao; Yu, Yi Yin; Choi, JaeMyung; Jeong, Jeung-hyun; Hwang, David J.

2018-03-01

Cu(In,Ga)Se2 (CIGS) thin films, a promising photovoltaic architecture, have mainly relied on Molybdenum for the bottom contact. However, the opaque nature of Molybdenum (Mo) poses limitations in module level fabrication by laser scribing as a preferred method for interconnect. We examined the P1, P2, and P3 laser scribing processes on CIGS photovoltaic architecture on the indium tin oxide (ITO) bottom contact with a cost-effective nanosecond pulsed laser of 532 nm wavelength. Laser illuminated from the substrate side, enabled by the transparent bottom contact, facilitated selective laser energy deposition onto relevant interfaces towards high-quality scribing. Parametric tuning procedures are described in conjunction with experimental and numerical investigation of relevant mechanisms, and preliminary mini-module fabrication results are also presented.

COMPARISON OF TOP AND BOTTOM LOADING OF A DEXTRAN GRADIENT FOR RAT PANCREATIC-ISLET PURIFICATION

NARCIS (Netherlands)

FRITSCHY, WM; VANSUYLICHEM, PTR; WOLTERS, GHJ; VANSCHILFGAARDE, R

Rat pancreatic islet yields obtained with dextran gradient purification were compared after suspending the digest into either the top or the bottom layer of the gradient. A 5-layer discontinuous gradient was used, which consisted of 16 ml 31% dextran as bottom layer, overlayered with 25%, 23%, 20%

Graft fixation with predetermined tension using a new device, the double spike plate.

Science.gov (United States)

Shino, Konsei; Mae, Tatsuo; Maeda, Akira; Miyama, Takahide; Shinjo, Hirotaka; Kawakami, Hideo

2002-10-01

To biomechanically evaluate a new fixation device, DSP (Double Spike Plate; Meira Corp, Nagoya, Aichi, Japan), for pullout graft fixation. Biomechanical study. A porcine tibia in which 8-mm diameter drill holes had been made from the medial tibial metaphysis to the anterior cruciate ligament attachment was rigidly fixed to a tension analyzer. A quadrupled graft consisting of 2 double-looped bovine tendons was prepared with No. 3 polyester sutures placed distally. The graft was passed through the drill hole, and its proximal loop ends were rigidly fixed to a load cell for monitoring graft tension. The graft's distal ends were connected to the DSP by tying the sutures to the top hole in the DSP. The graft tension was predetermined at 49 N (n = 5) or 98 N (n = 5). This tension was maintained for 5 minutes with a suture passed through the bottom hole of the DSP. The plate was fixed to the tibia by hammering its spikes into the bone under the index tension. Finally, the fixation was completed by inserting a screw. Although the graft tension immediately increased to 69 +/- 11 N or 133 +/- 14 N during hammering, it gradually reduced to 49 +/- 10 N or 100 +/- 7 N 5 minutes later. This study shows that graft fixation under a predetermined tension can be achieved with the DSP.

NEFSC 2002 Winter Bottom Trawl Survey (AL0203, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2002 Fall Bottom Trawl Survey (AL0210, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2011 Fall Bottom Trawl Survey (HB1105, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2008 Spring Bottom Trawl Survey (AL0801, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2008 Spring Bottom Trawl Survey (HB0802, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2015 Fall Bottom Trawl Survey (HB1506, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2011 Spring Bottom Trawl Survey (HB1102, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2007 Bottom Trawl Survey Calibration (HB0711, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2003 Spring Bottom Trawl Survey (DE0303, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2008 Fall Bottom Trawl Survey (AL0803, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2004 Winter Bottom Trawl Survey (AL0401, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2005 Fall Bottom Trawl Survey (AL0508, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 1998 Fall Bottom Trawl Survey (AL9811, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2009 Spring Bottom Trawl Survey (HB0901, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2012 Spring Bottom Trawl Survey (HB1201, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2015 Spring Bottom Trawl Survey (HB1501, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2004 Spring Bottom Trawl Survey (AL0403, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 1999 Fall Bottom Trawl Survey (AL9911, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2005 Fall Bottom Trawl Survey (AL0509, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2012 Fall Bottom Trawl Survey (HB1206, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2013 Fall Bottom Trawl Survey (HB1304, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2010 Spring Bottom Trawl Survey (HB1002, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2016 Fall Bottom Trawl Survey (HB1604, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2000 Fall Bottom Trawl Survey (Al0006, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2000 Fall Bottom Trawl Survey (AL0007, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2005 Winter Bottom Trawl Survey (AL0502, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2009 Fall Bottom Trawl Survey (HB0905, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2004 Fall Bottom Trawl Survey (AL0409, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2013 Spring Bottom Trawl Survey (HB1301, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2014 Fall Bottom Trawl Survey (HB1405, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2014 Spring Bottom Trawl Survey (HB1401, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2007 Bottom Trawl Survey Calibration (HB0710, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2005 Spring Bottom Trawl Survey (AL0504, EK500)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2016 Spring Bottom Trawl Survey (HB1601, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

NEFSC 2008 Fall Bottom Trawl Survey (HB0807, EK60)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — The NEFSC bottom trawl survey is a fisheries independent, multi-species survey that provides the primary scientific data for fisheries assessments in the U.S....

Double Outlet Right Ventricle

Science.gov (United States)

... Right Ventricle Menu Topics Topics FAQs Double Outlet Right Ventricle Double outlet right ventricle (DORV) is a rare form of congenital heart disease. En español Double outlet right ventricle (DORV) is a rare form of congenital ...

Impact of bottom trawling on sediment characteristics - A study along inshore waters off Veraval coast, India

Digital Repository Service at National Institute of Oceanography (India)

Bhagirathan, U.; Meenakumari, B.; Jayalakshmy, K.V.; Panda, S.K.; Madhu, V.R.; Vaghela, D.T.

The present communication is a study on the impact of bottom trawling on the sediment characteristics along Veraval coast, which is the largest trawler port of India. Experimental bottom trawling was conducted from MFV Sagarkripa at five transects...

Use of co-combustion bottom ash to design an acoustic absorbing material for highway noise barriers

International Nuclear Information System (INIS)

Arenas, Celia; Leiva, Carlos; Vilches, Luis F.; Cifuentes, Héctor

2013-01-01

Highlights: • The particle size of bottom ash influenced the acoustic behavior of the barrier. • The best sound absorption coefficients were measured for larger particle sizes. • The maximum noise absorption is displaced to lower frequencies for higher thickness. • A noise barrier was designed with better properties than commercial products. • Recycling products from bottom ash no present leaching and radioactivity problems. - Abstract: The present study aims to determine and evaluate the applicability of a new product consisting of coal bottom ash mixed with Portland cement in the application of highway noise barriers. In order to effectively recycle the bottom ash, the influence of the grain particle size of bottom ash, the thickness of the panel and the combination of different layers with various particle sizes have been studied, as well as some environmental properties including leachability (EN-12457-4, NEN-7345) and radioactivity tests. Based on the obtained results, the acoustic properties of the final composite material were similar or even better than those found in porous concrete used for the same application. According to this study, the material produced presented no environmental risk

Re-initiation of bottom water formation in the East Sea (Japan Sea) in a warming world.

Science.gov (United States)

Yoon, Seung-Tae; Chang, Kyung-Il; Nam, SungHyun; Rho, TaeKeun; Kang, Dong-Jin; Lee, Tongsup; Park, Kyung-Ae; Lobanov, Vyacheslav; Kaplunenko, Dmitry; Tishchenko, Pavel; Kim, Kyung-Ryul

2018-01-25

The East Sea (Japan Sea), a small marginal sea in the northwestern Pacific, is ventilated deeply down to the bottom and sensitive to changing surface conditions. Addressing the response of this marginal sea to the hydrological cycle and atmospheric forcing would be helpful for better understanding present and future environmental changes in oceans at the global and regional scales. Here, we present an analysis of observations revealing a slowdown of the long-term deepening in water boundaries associated with changes of water formation rate. Our results indicate that bottom (central) water formation has been enhanced (reduced) with more (less) oxygen supply to the bottom (central) layer since the 2000s. This paper presents a new projection that allows a three-layered deep structure, which retains bottom water, at least until 2040, contrasting previous results. This projection considers recent increase of slope convections mainly due to the salt supply via air-sea freshwater exchange and sea ice formation and decrease of open-ocean convections evidenced by reduced mixed layer depth in the northern East Sea, resulting in more bottom water and less central water formations. Such vigorous changes in water formation and ventilation provide certain implications on future climate changes.

Use of co-combustion bottom ash to design an acoustic absorbing material for highway noise barriers

Energy Technology Data Exchange (ETDEWEB)

Arenas, Celia; Leiva, Carlos; Vilches, Luis F. [University of Seville, School of Industrial Engineering, Department of Chemical and Environmental Engineering, Camino de los Descubrimientos s/n, E-41092 Seville (Spain); Cifuentes, Héctor, E-mail: bulte@us.es [University of Seville, School of Industrial Engineering, Continuum Mechanics and Structural Analysis Department, Camino de los Descubrimientos s/n, E-41092 Seville (Spain)

2013-11-15

Highlights: • The particle size of bottom ash influenced the acoustic behavior of the barrier. • The best sound absorption coefficients were measured for larger particle sizes. • The maximum noise absorption is displaced to lower frequencies for higher thickness. • A noise barrier was designed with better properties than commercial products. • Recycling products from bottom ash no present leaching and radioactivity problems. - Abstract: The present study aims to determine and evaluate the applicability of a new product consisting of coal bottom ash mixed with Portland cement in the application of highway noise barriers. In order to effectively recycle the bottom ash, the influence of the grain particle size of bottom ash, the thickness of the panel and the combination of different layers with various particle sizes have been studied, as well as some environmental properties including leachability (EN-12457-4, NEN-7345) and radioactivity tests. Based on the obtained results, the acoustic properties of the final composite material were similar or even better than those found in porous concrete used for the same application. According to this study, the material produced presented no environmental risk.

Nutrient loading and metabolism in hard-bottom littoral mesocosms

NARCIS (Netherlands)

Kersting, K.; Lindblad, C.

2001-01-01

In eight hard-bottom tidal littoral mesocosms oxygen concentrations and temperature were measured every 30 s and registered as 15 min-averages. The mesocosms were fed with water from the Oslofjord (residence time about 2 h) and the measurements were also performed in the inflow. In addition,

Construction for holding together a cylindrical high pressure reactor vessel with hemispherical bottom and lid

International Nuclear Information System (INIS)

Desmarchais, W.E.; Braun, H.E.

1972-01-01

The construction shall prevent that in case of ruptures of the vessel rupture pieces may damage the secondary shielding system. The construction consists of two yokes fitting to the bottom and the lid of the vessel and held together by means of pull rods. The yokes are designed as truncated conshaped shells. The smaller end of the cone shells supports the hemispherical bottom and the lid of the vessel. The larger cone shell ends are tied together by the pull rods. As further improvements there may be arranged hemispherical protective shields between the hemispherical bottom and the lid of the vessel and the smaller end of the cone shells. (P.K.)

Method of retrieving an object buried in the bottom of a body of water

Energy Technology Data Exchange (ETDEWEB)

van Steveninck, J

1975-05-14

In this method of retrieving an object buried in the bottom of a body of water, the object to be retrieved has a number of openings or nozzles, with the aid of at least some of which the object has been buried by fluidization in the bottom of a body of water, for example a fluidization device for burying a pipeline or a fluidization anchor. The method consists of supplying a gas to the buried object, allowing the gas to pass to and through openings or nozzles on the object in such a manner that the gas will be introduced into, and will refluidize the bottom material above the object, and raising the object. Experiments have shown that in this manner fluidization can be reestablished immediately, due to the low density and the low viscosity of the gas, whereafter the object due to the low resistance of the refluidized bottom material is easy to raise to the surface, even after the fluidization has been interrupted for a long period of time. Preferably, the gas used is air, since air is readily available; however, other gases can be used, if desired. (7 claims)

Bottom-up learning of hierarchical models in a class of deterministic POMDP environments

Directory of Open Access Journals (Sweden)

Itoh Hideaki

2015-09-01

Full Text Available The theory of partially observable Markov decision processes (POMDPs is a useful tool for developing various intelligent agents, and learning hierarchical POMDP models is one of the key approaches for building such agents when the environments of the agents are unknown and large. To learn hierarchical models, bottom-up learning methods in which learning takes place in a layer-by-layer manner from the lowest to the highest layer are already extensively used in some research fields such as hidden Markov models and neural networks. However, little attention has been paid to bottom-up approaches for learning POMDP models. In this paper, we present a novel bottom-up learning algorithm for hierarchical POMDP models and prove that, by using this algorithm, a perfect model (i.e., a model that can perfectly predict future observations can be learned at least in a class of deterministic POMDP environments

New-Generation Aluminum Composite with Bottom Ash Industrial Waste

Science.gov (United States)

Mandal, A. K.; Sinha, O. P.

2018-02-01

Industrial waste bottom ash (BA) from a pulverized coal combustion boiler containing hard wear-resistant particles was utilized in this study to form an aluminum composite through a liquid metallurgy route. Composites comprising 5 wt.% and 10 wt.% bottom ash were characterized for their physiochemical, microstructural, mechanical, as well as tribological properties, along with pure aluminum. Scanning electron microscopy (SEM) microstructure revealed uniform distribution of BA particles throughout the matrix of the composite, whereas x-ray diffraction (XRD) analysis confirmed presence of aluminosilicate phase. Addition of 10 wt.% BA improved the Brinell hardness number (BHN) from 13 to 19 and ultimate tensile strength (UTS) from 71 MPa to 87 MPa, whereas ductility was adversely reduced after 5% BA addition. Incorporation of BA particles resulted in reduced dry sliding wear rates examined up to 80 N load compared with aluminum. Hence, such composites having lower cost could be applied as significantly hard, wear-resistant materials in applications in the automotive industry.

New-Generation Aluminum Composite with Bottom Ash Industrial Waste

Science.gov (United States)

Mandal, A. K.; Sinha, O. P.

2018-06-01

Industrial waste bottom ash (BA) from a pulverized coal combustion boiler containing hard wear-resistant particles was utilized in this study to form an aluminum composite through a liquid metallurgy route. Composites comprising 5 wt.% and 10 wt.% bottom ash were characterized for their physiochemical, microstructural, mechanical, as well as tribological properties, along with pure aluminum. Scanning electron microscopy (SEM) microstructure revealed uniform distribution of BA particles throughout the matrix of the composite, whereas x-ray diffraction (XRD) analysis confirmed presence of aluminosilicate phase. Addition of 10 wt.% BA improved the Brinell hardness number (BHN) from 13 to 19 and ultimate tensile strength (UTS) from 71 MPa to 87 MPa, whereas ductility was adversely reduced after 5% BA addition. Incorporation of BA particles resulted in reduced dry sliding wear rates examined up to 80 N load compared with aluminum. Hence, such composites having lower cost could be applied as significantly hard, wear-resistant materials in applications in the automotive industry.

Alternative ORC bottoming cycles FOR combined cycle power plants

International Nuclear Information System (INIS)

Chacartegui, R.; Sanchez, D.; Munoz, J.M.; Sanchez, T.

2009-01-01

In this work, low temperature Organic Rankine Cycles are studied as bottoming cycle in medium and large scale combined cycle power plants. The analysis aims to show the interest of using these alternative cycles with high efficiency heavy duty gas turbines, for example recuperative gas turbines with lower gas turbine exhaust temperatures than in conventional combined cycle gas turbines. The following organic fluids have been considered: R113, R245, isobutene, toluene, cyclohexane and isopentane. Competitive results have been obtained for toluene and cyclohexane ORC combined cycles, with reasonably high global efficiencies. The paper is structured in four main parts. A review of combined cycle and ORC cycle technologies is presented, followed by a thermodynamic analysis of combined cycles with commercial gas turbines and ORC low temperature bottoming cycles. Then, a parametric optimization of an ORC combined cycle plant is performed in order to achieve a better integration between these two technologies. Finally, some economic considerations related to the use of ORC in combined cycles are discussed.

Integrating the bottom-up and top-down approach to energy economy modelling. The case of Denmark

DEFF Research Database (Denmark)

Klinge Jacobsen, Henrik

1998-01-01

This paper presents results from an integration project covering Danish models based on bottom-up and top-down approaches to energy]economy modelling. The purpose of the project was to identify theoretical and methodological problems for integrating existing models for Denmark and to implement...... an integration of the models. The integration was established through a number of links between energy bottom-up modules and a macroeconomic model. In this integrated model it is possible to analyse both top-down instruments, such as taxes along with bottom-up instruments, such as regulation of technology...

Study of tritium permeation through Peach Bottom Steam Generator tubes

International Nuclear Information System (INIS)

Yang, L.; Baugh, W.A.; Baldwin, N.L.

1977-06-01

The report describes the equipment developed, samples tested, procedures used, and results obtained in the tritium permeation tests conducted on steam generator tubing samples which were removed from the Peach Bottom Unit No. 1 reactor

The Bottom Line: Industry and the Environment in South Africa ...

International Development Research Centre (IDRC) Digital Library (Canada)

The Bottom Line is a major new contribution to the debates on industry and the ... and the environmental management of small and medium-sized enterprises. ... book will appeal to industrial managers, environmentalists, lawyers, engineers, ...

Congenital double-double lip: A rare case report

Directory of Open Access Journals (Sweden)

Swati Phore

2017-01-01

Full Text Available A double lip is a rare anomaly characterized by a horizontal fold of redundant mucosal tissue that is situated proximal to the vermilion border. It may be either congenital or acquired and has no gender or race predilection. It occurs most often in the upper lip, although both upper and lower lips are occasionally involved. Surgical intervention (simple excision produces good functional and cosmetic results. In this report, a case of a nonsyndromic congenital maxillary double upper lip and lower lip, both are described. Double lip is of special interest in dental profession as a dental surgeon is normally the first one to diagnose this rare and uncommon condition. Authors hereby discuss a very rare condition in which both upper and lower lips are involved.

The Fishery Performance Indicators: A Management Tool for Triple Bottom Line Outcomes

Science.gov (United States)

Anderson, James L.; Anderson, Christopher M.; Chu, Jingjie; Meredith, Jennifer; Asche, Frank; Sylvia, Gil; Smith, Martin D.; Anggraeni, Dessy; Arthur, Robert; Guttormsen, Atle; McCluney, Jessica K.; Ward, Tim; Akpalu, Wisdom; Eggert, Håkan; Flores, Jimely; Freeman, Matthew A.; Holland, Daniel S.; Knapp, Gunnar; Kobayashi, Mimako; Larkin, Sherry; MacLauchlin, Kari; Schnier, Kurt; Soboil, Mark; Tveteras, Sigbjorn; Uchida, Hirotsugu; Valderrama, Diego

2015-01-01

Pursuit of the triple bottom line of economic, community and ecological sustainability has increased the complexity of fishery management; fisheries assessments require new types of data and analysis to guide science-based policy in addition to traditional biological information and modeling. We introduce the Fishery Performance Indicators (FPIs), a broadly applicable and flexible tool for assessing performance in individual fisheries, and for establishing cross-sectional links between enabling conditions, management strategies and triple bottom line outcomes. Conceptually separating measures of performance, the FPIs use 68 individual outcome metrics—coded on a 1 to 5 scale based on expert assessment to facilitate application to data poor fisheries and sectors—that can be partitioned into sector-based or triple-bottom-line sustainability-based interpretative indicators. Variation among outcomes is explained with 54 similarly structured metrics of inputs, management approaches and enabling conditions. Using 61 initial fishery case studies drawn from industrial and developing countries around the world, we demonstrate the inferential importance of tracking economic and community outcomes, in addition to resource status. PMID:25946194

Top-down or bottom-up modelling. An application to CO2 abatement

International Nuclear Information System (INIS)

Laroui, F.; Van Leeuwen, M.J.

1995-06-01

In four articles a comparison is made of bottom-up, or engineers'' models, and top-down models, which comprise macro-econometric models, computable general equilibrium models and also models in the system dynamics tradition. In the first article the history of economic modelling is outlined. In the second article the multi-sector macro-economic Computable General Equilibrium model for the Netherlands is described. It can be used to study the long-term effects of fiscal policy measures on economic and environmental indicators, in particular the effects on the level of CO2-emissions. The aim of article 3 is to describe the structure of the electricity supply industry in the UK and how it can be represented in a bottom-up sub-model within a more general E3 sectoral model of the UK economy. The objective of the last paper (4) is mainly a methodological discussion about integrating top-down and bottom-up models which can be used to assess CO2 abatement policies impacts on economic activity

Assessing the Efficiency of Small-Scale and Bottom Trawler Vessels in Greece

Directory of Open Access Journals (Sweden)

Dario Pinello

2016-07-01

Full Text Available This study explores the technical and scale efficiency of two types of Greek fishing vessels, small-scale vessels and bottom trawlers, using a bias-corrected input-oriented Data Envelopment Analysis model. Moreover, the associations between efficiency scores and vessel’s and skipper’s characteristics are also explored. The results indicate that small-scale vessels achieve a very low average technical efficiency score (0.42 but a much higher scale efficiency score (0.81. Conversely, bottom trawlers achieve lower scale but higher technical efficiency scores (0.68 and 0.73, respectively. One important finding of this study is that the technical efficiency of small-scale vessels, in contrast to trawlers, is positively associated with the experience of the skipper. In a looser context, it can be said that small-scale fisheries mainly rely on skill, whereas bottom trawlers rely more on technology. This study concludes that there is space for improvement in efficiency, mainly for small-scale vessels, which could allow the achievement of the same level of output by using reduced inputs.

Thermo-economic analysis of recuperated Maisotsenko bottoming cycle using triplex air saturator: Comparative analyses

International Nuclear Information System (INIS)

Saghafifar, Mohammad; Omar, Amr; Erfanmoghaddam, Sepehr; Gadalla, Mohamed

2017-01-01

Highlights: • Proposing recuperated Maisotsenko bottoming cycle (RMBC) as a new combined cycle. • Introducing triplex air saturator for waste heat recovery application. • Conducting thermodynamic optimization to maximize RMBC thermal efficiency. • Conducting thermo-economic optimization to minimize RMBC cost of electricity. - Abstract: A recently recommended combined cycle power plant is to employ another gas turbine cycle for waste heat recovery as an air bottoming cycle (ABC). There are some studies conducted to improve ABC’s thermodynamic performance utilizing commonly power augmentation methods such as steam/water injection. In particular, it is proposed to employ Maisotsenko gas turbine cycle as a bottoming cycle, i.e. Maisotsenko bottoming cycle (MBC). Due to the promising performance of the MBC configuration, it is decided to investigate a recuperated MBC (RMBC) configuration by recommending the triplex air saturator. In this way, the air saturator consists of three sections. The first section is an indirect evaporative cooler while the other two sections are responsible for heat recovery from the topping and bottoming cycle turbines exhaust. In this paper, thermodynamic and thermo-economic analyses are carried out to study the main merits and demerits of RMBC against MBC configuration. Thermodynamic optimization results indicate that the maximum achievable efficiency for MBC and RMBC incorporation in a simple gas turbine power plant are 39.40% and 44.73%, respectively. Finally, thermo-economic optimization shows that the optimum levelized cost of electricity for MBC and RMBC power plants are 62.922 US$/MWh and 58.154 US$/MWh, respectively.

Individualized FAC on bottom tab subassemblies to minimize adhesive gap between emitter and optics

Science.gov (United States)

Sauer, Sebastian; Müller, Tobias; Haag, Sebastian; Beleke, Andreas; Zontar, Daniel; Baum, Christoph; Brecher, Christian

2017-02-01

High Power Diode Laser (HPDL) systems with short focal length fast-axis collimators (FAC) require submicron assembly precision. Conventional FAC-Lens assembly processes require adhesive gaps of 50 microns or more in order to compensate for component tolerances (e.g. deviation of back focal length) and previous assembly steps. In order to control volumetric shrinkage of fast-curing UV-adhesives shrinkage compensation is mandatory. The novel approach described in this paper aims to minimize the impact of volumetric shrinkage due to the adhesive gap between HPDL edge emitters and FAC-Lens. Firstly, the FAC is actively aligned to the edge emitter without adhesives or bottom tab. The relative position and orientation of FAC to emitter are measured and stored. Consecutively, an individual subassembly of FAC and bottom tab is assembled on Fraunhofer IPT's mounting station with a precision of +/-1 micron. Translational and lateral offsets can be compensated, so that a narrow and uniform glue gap for the consecutive bonding process of bottom tab to heatsink applies (Figure 4). Accordingly, FAC and bottom tab are mounted to the heatsink without major shrinkage compensation. Fraunhofer IPT's department assembly of optical systems and automation has made several publications regarding active alignment of FAC lenses [SPIE LASE 8241-12], volumetric shrinkage compensation [SPIE LASE 9730-28] and FAC on bottom tab assembly [SPIE LASE 9727-31] in automated production environments. The approach described in this paper combines these and is the logical continuation of that work towards higher quality of HPDLs.

Effect of bottom type on catch rates of North Sea cod (Gadus morhua) in surveys with commercial fishing vessels

DEFF Research Database (Denmark)

Wieland, Kai; Pedersen, Eva Maria; Olesen, Hans Jakob

2009-01-01

were substantially higher on gravel or stone bottom and at ship wrecks than on sand bottom. The difference in the catch rates between the two bottom categories at paired stations within a short distance was highly significant for all the three fishing methods. Similarly, average CPUE for most surveys...

Ocean Thermal Conversion (OTEC) Project Bottom Cable Protection Study: Environmental Characteristics and Hazards Analysis,

Science.gov (United States)

1981-10-01

Chesaneake Division, Naval Facilities Engineering Command, Washington, DC) 34. "Strait of Belle Isle Crossing HVDC Transmission - Submarine Cable...phenomena; such as wind storm generated wave action, bottom currents, bottom mudslides, or seismic activity; as well as human activity, such as...engaging a cable. Ship anchors are used to develop holding power on the seafloor for mooring a floating body permanently or temporary on site. The major

State of the soft bottoms of the continental shelf

International Nuclear Information System (INIS)

Guzman Alvis, Angela I; Solano, Oscar David

2002-01-01

The presented information, it is based on studies carried out on the continental shelf of the Colombian Caribbean, mainly in the Gulf of Morrosquillo and the Magdalena and Guajira departments in the last ten years. A diagnostic is done of the soft bottoms of the Colombian continental shelf

Synthesis of Zeolite-X from Bottom Ash for H2 Adsorption

Science.gov (United States)

Kurniawan, R. Y.; Romadiansyah, T. Q.; Tsamarah, A. D.; Widiastuti, N.

2018-01-01

Zeolite-X was synthesized from bottom ash power plant waste using fusion method on air atmosphere. The fused product dissolved in demineralized water and aluminate solution was added to adjust the SiO2/Al2O3 molar ratio gel prior hydrothermal process. The synthesis results were characterized using X-Ray Diffraction (XRD), Scanning Electron Microscope (SEM), and Fourier Transform Infrared (FTIR). The results showed that the zeolite-X has a high crystallinity with octahedral particle. The pure-form zeolite-X then was characterized and tested for H2 gas adsorption by gravimetric method to determine the H2 gas adsorption capacity of zeolite-X from bottom ash and it was compared to synthetic zeolite-X.

Neoliberalism Viewed From the Bottom Up

DEFF Research Database (Denmark)

Danneris, Sophie

2017-01-01

Drawing on the assumption that it is pivotal to include a bottom up perspective to understand the way in which the welfare system functions, this chapter sets out to explore the lived experience of neoliberalism. The purpose is to gain insight into the consequences of neoliberalism from...... the viewpoint of the vulnerable benefit claimants who encounter it on a daily basis. The analysis is based on a qualitative longitudinal study conducted from 2013 to 2015, which shows how, in varying ways, clients routinely cope with being part of a neoliberal welfare state: by resignation, by taking action...

a New Technique Based on Mini-Uas for Estimating Water and Bottom Radiance Contributions in Optically Shallow Waters

Science.gov (United States)

Montes-Hugo, M. A.; Barrado, C.; Pastor, E.

2015-08-01

The mapping of nearshore bathymetry based on spaceborne radiometers is commonly used for QC ocean colour products in littoral waters. However, the accuracy of these estimates is relatively poor with respect to those derived from Lidar systems due in part to the large uncertainties of bottom depth retrievals caused by changes on bottom reflectivity. Here, we present a method based on mini unmanned aerial vehicles (UAS) images for discriminating bottom-reflected and water radiance components by taking advantage of shadows created by different structures sitting on the bottom boundary. Aerial surveys were done with a drone Draganfly X4P during October 1 2013 in optically shallow waters of the Saint Lawrence Estuary, and during low tide. Colour images with a spatial resolution of 3 mm were obtained with an Olympus EPM-1 camera at 10 m height. Preliminary results showed an increase of the relative difference between bright and dark pixels (dP) toward the red wavelengths of the camera's receiver. This is suggesting that dP values can be potentially used as a quantitative proxy of bottom reflectivity after removing artefacts related to Fresnel reflection and bottom adjacency effects.

Use of Unprocessed Coal Bottom Ash as Partial Fine Aggregate ...

African Journals Online (AJOL)

2012r

transportation applications such as structural fill, road base material, and as snow ... normal fine particles resulting in weak porous paste, modulus of elasticity is ..... with the porous structure and high absorptivity of fine particles of bottom ash.

The effects of physiology and behaviour on the near-bottom ...

African Journals Online (AJOL)

African Journal of Marine Science ... behaviour on the near-bottom distributions of Karenia brevis on the West Florida shelf: a numerical study ... In shallow, more turbid environments, migrating cells access between 35% and 67% of the light

Comparative analyses of contaminant levels in bottom feeding and predatory fish using the National Contaminant Biomonitoring Program data

Energy Technology Data Exchange (ETDEWEB)

Kidwell, J.M. [Clement International Corp., Fairfax, VA (United States); Phillips, L.J. [Versar Inc., Springfield, VA (United States); Birchard, G.F. [George Mason Univ., Fairfax, VA (United States)

1995-06-01

Both bottom feeding and predatory fish accumulate chemical contaminants found in water. Bottom feeders are readily exposed to the greater quantities of chlorinated hydrocarbons and metals that accumulate in sediments. Predators, on the other hand, may bioaccumulate organochlorine pesticides, PCBs, and metals from the surrounding water or from feeding on other fish, including bottom feeders, which may result in the biomagnification of these compounds in their tissues. This study used National Contaminant Biomonitoring Program data produced by the Fish and Wildlife Service to test the hypothesis that differences exist between bottom feeders and predators in tissue levels of organochlorine pesticides, PCBs, and metals. 7 refs., 2 tabs.

Searches for scalar top and scalar bottom quarks at LEP2

CERN Document Server

Barate, R; Décamp, D; Ghez, P; Goy, C; Lees, J P; Lucotte, A; Minard, M N; Nief, J Y; Pietrzyk, B; Casado, M P; Chmeissani, M; Comas, P; Crespo, J M; Delfino, M C; Fernández, E; Fernández-Bosman, M; Garrido, L; Juste, A; Martínez, M; Merino, G; Miquel, R; Mir, L M; Padilla, C; Park, I C; Pascual, A; Perlas, J A; Riu, I; Sánchez, F; Teubert, F; Colaleo, A; Creanza, D; De Palma, M; Gelao, G; Iaselli, Giuseppe; Maggi, G; Maggi, M; Marinelli, N; Nuzzo, S; Ranieri, A; Raso, G; Ruggieri, F; Selvaggi, G; Silvestris, L; Tempesta, P; Tricomi, A; Zito, G; Huang, X; Lin, J; Ouyang, Q; Wang, T; Xie, Y; Xu, R; Xue, S; Zhang, J; Zhang, L; Zhao, W; Abbaneo, D; Alemany, R; Bazarko, A O; Becker, U; Bright-Thomas, P G; Cattaneo, M; Cerutti, F; Dissertori, G; Drevermann, H; Forty, Roger W; Frank, M; Hagelberg, R; Hansen, J B; Harvey, J; Janot, P; Jost, B; Kneringer, E; Knobloch, J; Lehraus, Ivan; Mato, P; Minten, Adolf G; Moneta, L; Pacheco, A; Pusztaszeri, J F; Ranjard, F; Rizzo, G; Rolandi, Luigi; Rousseau, D; Schlatter, W D; Schmitt, M; Schneider, O; Tejessy, W; Tomalin, I R; Wachsmuth, H W; Wagner, A; Ajaltouni, Ziad J; Barrès, A; Boyer, C; Falvard, A; Ferdi, C; Gay, P; Guicheney, C; Henrard, P; Jousset, J; Michel, B; Monteil, S; Montret, J C; Pallin, D; Perret, P; Podlyski, F; Proriol, J; Rosnet, P; Rossignol, J M; Fearnley, Tom; Hansen, J D; Hansen, J R; Hansen, P H; Nilsson, B S; Rensch, B; Wäänänen, A; Daskalakis, G; Kyriakis, A; Markou, C; Simopoulou, Errietta; Vayaki, Anna; Blondel, A; Brient, J C; Machefert, F P; Rougé, A; Rumpf, M; Valassi, Andrea; Videau, H L; Focardi, E; Parrini, G; Zachariadou, K; Cavanaugh, R J; Corden, M; Georgiopoulos, C H; Hühn, T; Jaffe, D E; Antonelli, A; Bencivenni, G; Bologna, G; Bossi, F; Campana, P; Capon, G; Casper, David William; Chiarella, V; Felici, G; Laurelli, P; Mannocchi, G; Murtas, F; Murtas, G P; Passalacqua, L; Pepé-Altarelli, M; Curtis, L; Dorris, S J; Halley, A W; Knowles, I G; Lynch, J G; O'Shea, V; Raine, C; Scarr, J M; Smith, K; Teixeira-Dias, P; Thompson, A S; Thomson, E; Thomson, F; Turnbull, R M; Buchmüller, O L; Dhamotharan, S; Geweniger, C; Graefe, G; Hanke, P; Hansper, G; Hepp, V; Kluge, E E; Putzer, A; Sommer, J; Tittel, K; Werner, S; Wunsch, M; Beuselinck, R; Binnie, David M; Cameron, W; Dornan, Peter J; Girone, M; Goodsir, S M; Martin, E B; Morawitz, P; Moutoussi, A; Nash, J; Sedgbeer, J K; Spagnolo, P; Stacey, A M; Williams, M D; Ghete, V M; Girtler, P; Kuhn, D; Rudolph, G; Betteridge, A P; Bowdery, C K; Colrain, P; Crawford, G; Finch, A J; Foster, F; Hughes, G; Jones, R W L; Sloan, Terence; Whelan, E P; Williams, M I; Hoffmann, C; Jakobs, K; Kleinknecht, K; Quast, G; Renk, B; Rohne, E; Sander, H G; Van Gemmeren, P; Zeitnitz, C; Aubert, Jean-Jacques; Benchouk, C; Bonissent, A; Bujosa, G; Carr, J; Coyle, P; Diaconu, C A; Ealet, A; Fouchez, D; Konstantinidis, N P; Leroy, O; Motsch, F; Payre, P; Talby, M; Sadouki, A; Thulasidas, M; Tilquin, A; Trabelsi, K; Aleppo, M; Antonelli, M; Ragusa, F; Berlich, R; Blum, Walter; Büscher, V; Dietl, H; Ganis, G; Gotzhein, C; Kroha, H; Lütjens, G; Lutz, Gerhard; Männer, W; Moser, H G; Richter, R H; Rosado-Schlosser, A; Schael, S; Settles, Ronald; Seywerd, H C J; Saint-Denis, R; Stenzel, H; Wiedenmann, W; Wolf, G; Boucrot, J; Callot, O; Chen, S; Cordier, A; Davier, M; Duflot, L; Grivaz, J F; Heusse, P; Höcker, A; Jacholkowska, A; Jacquet, M; Kim, D W; Le Diberder, F R; Lefrançois, J; Lutz, A M; Nikolic, I A; Schune, M H; Serin, L; Simion, S; Tournefier, E; Veillet, J J; Videau, I; Zerwas, D; Azzurri, P; Bagliesi, G; Bettarini, S; Bozzi, C; Calderini, G; Ciulli, V; Dell'Orso, R; Fantechi, R; Ferrante, I; Giassi, A; Gregorio, A; Ligabue, F; Lusiani, A; Marrocchesi, P S; Messineo, A; Palla, Fabrizio; Sanguinetti, G; Sciabà, A; Sguazzoni, G; Steinberger, Jack; Tenchini, Roberto; Vannini, C; Venturi, A; Verdini, P G; Blair, G A; Bryant, L M; Chambers, J T; Gao, Y; Green, M G; Medcalf, T; Perrodo, P; Strong, J A; Von Wimmersperg-Töller, J H; Botterill, David R; Clifft, R W; Edgecock, T R; Haywood, S; Maley, P; Norton, P R; Thompson, J C; Wright, A E; Bloch-Devaux, B; Colas, P; Fabbro, B; Kozanecki, Witold; Lançon, E; Lemaire, M C; Locci, E; Pérez, P; Rander, J; Renardy, J F; Rosowsky, A; Roussarie, A; Schuller, J P; Schwindling, J; Trabelsi, A; Vallage, B; Black, S N; Dann, J H; Kim, H Y; Litke, A M; McNeil, M A; Taylor, G; Booth, C N; Boswell, R; Brew, C A J; Cartwright, S L; Combley, F; Kelly, M S; Lehto, M H; Newton, W M; Reeve, J; Thompson, L F; Affholderbach, K; Böhrer, A; Brandt, S; Cowan, G D; Foss, J; Grupen, Claus; Lutters, G; Saraiva, P; Smolik, L; Stephan, F; Apollonio, M; Bosisio, L; Della Marina, R; Giannini, G; Gobbo, B; Musolino, G; Pütz, J; Rothberg, J E; Wasserbaech, S R; Williams, R W; Armstrong, S R; Charles, E; Elmer, P; Ferguson, D P S; González, S; Greening, T C; Hayes, O J; Hu, H; Jin, S; McNamara, P A; Nachtman, J M; Nielsen, J; Orejudos, W; Pan, Y B; Saadi, Y; Scott, I J; Walsh, J; Wu Sau Lan; Wu, X; Yamartino, J M; Zobernig, G

1997-01-01

Searches for scalar top and bottom quarks have been performed with data collected by the ALEPH detector at LEP. The data sample consists of 21.7 pb^-1 taken at sqrt{s} = 161, 170, and 172~GeV and 5.7 pb^-1 taken at sqrt{s} = 130 and 136~GeV. No evidence for scalar top quarks or scalar bottom quarks was found in the channels stop --> c chi, stop --> b l snu, and sbottom --> b chi. For the channel stop --> c chi a limit of 67 GeV/c^2 has been set on the scalar top quark mass, independent of the mixing angle between the supersymmetric partners of the left and right-handed states of the top quark. This limit assumes a mass difference between the stop and the chi of at least 10 GeV/c^2. For the channel stop --> b l snu the mixing-angle independent scalar top limit is 70 GeV/c^2, assuming a mass difference between the stop and the snu of at least 10 GeV/c^2. For the channel sbottom --> b chi, a limit of 73 GeV/c^2 has been set on the mass of the supersymmetric partner of the left-handed state of the bottom quark. T...

Small Engines as Bottoming Cycle Steam Expanders for Internal Combustion Engines

Directory of Open Access Journals (Sweden)

Rohitha Weerasinghe

2017-01-01

Full Text Available Heat recovery bottoming cycles for internal combustion engines have opened new avenues for research into small steam expanders (Stobart and Weerasinghe, 2006. Dependable data for small steam expanders will allow us to predict their suitability as bottoming cycle engines and the fuel economy achieved by using them as bottoming cycles. Present paper is based on results of experiments carried out on small scale Wankel and two-stroke reciprocating engines as air expanders and as steam expanders. A test facility developed at Sussex used for measurements is comprised of a torque, power and speed measurements, electronic actuation of valves, synchronized data acquisition of pressure, and temperatures of steam and inside of the engines for steam and internal combustion cycles. Results are presented for four engine modes, namely, reciprocating engine in uniflow steam expansion mode and air expansion mode and rotary Wankel engine in steam expansion mode and air expansion mode. The air tests will provide base data for friction and motoring effects whereas steam tests will tell how effective the engines will be in this mode. Results for power, torque, and p-V diagrams are compared to determine the change in performance from air expansion mode to steam expansion mode.

Burlington Bottoms Wildlife Mitigation Project. Final Environmental Assessment/Management Plan and Finding of No Significant Impact.

Energy Technology Data Exchange (ETDEWEB)

1994-12-01

Bonneville Power Administration (BPA) proposes to fund wildlife management and enhancement activities for the Burlington bottoms wetlands mitigation site. Acquired by BPA in 1991, wildlife habitat at Burlington bottoms would contribute toward the goal of mitigation for wildlife losses and inundation of wildlife habitat due to the construction of Federal dams in the lower Columbia and Willamette River Basins. Target wildlife species identified for mitigation purposes are yellow warbler, great blue heron, black-capped chickadee, red-tailed hawk, valley quail, spotted sandpiper, wood duck, and beaver. The Draft Management Plan/Environmental Assessment (EA) describes alternatives for managing the Burlington Bottoms area, and evaluates the potential environmental impacts of the alternatives. Included in the Draft Management Plan/EA is an implementation schedule, and a monitoring and evaluation program, both of which are subject to further review pending determination of final ownership of the Burlington Bottoms property.

Burlington Bottoms Wildlife Mitigation Project. Final environmental assessment/management plan and finding of no significant impact

International Nuclear Information System (INIS)

1994-12-01

Bonneville Power Administration (BPA) proposes to fund wildlife management and enhancement activities for the Burlington bottoms wetlands mitigation site. Acquired by BPA in 1991, wildlife habitat at Burlington bottoms would contribute toward the goal of mitigation for wildlife losses and inundation of wildlife habitat due to the construction of Federal dams in the lower Columbia and Willamette River Basins. Target wildlife species identified for mitigation purposes are yellow warbler, great blue heron, black-capped chickadee, red-tailed hawk, valley quail, spotted sandpiper, wood duck, and beaver. The Draft Management Plan/Environmental Assessment (EA) describes alternatives for managing the Burlington Bottoms area, and evaluates the potential environmental impacts of the alternatives. Included in the Draft Management Plan/EA is an implementation schedule, and a monitoring and evaluation program, both of which are subject to further review pending determination of final ownership of the Burlington Bottoms property

Trace elements in bottom sediments of the Barents Sea on the standard section "Kola Meridian"

Directory of Open Access Journals (Sweden)

Lapteva A. M.

2017-03-01

Full Text Available The levels of trace metals (Cu, Zn, Ni, Cr, Mn, Co, Pb, Cd, Hg and arsenic (As in samples of bottom sediments from the Barents Sea on eight stations of the standard section "Kola Meridian" have been investigated. Trace elements have been determined on atomic absorption spectrophotometer AA-6800 with mercury-hydride attachment HVG-1 of the company Shimadzu (Japan by the methods of flaming (acetylene – air and electrothermal atomization. Common and very toxic trace elements include Pb, Cd, As, and Hg. It is believed that 90 % of lead, 70–80 % of cadmium, and arsenic, over 30 % of mercury in the atmosphere are of anthropogenic origin, and emissions of these elements in the atmosphere are almost completely manufactured in the Northern Hemisphere. The main sources of income in the Barents Sea are waters of the North Atlantic current and the large-scale atmospheric transport from industrialized Central Europe. As a rule the spatial distribution of trace elements is in good agreement with the granulometric composition of bottom sediments and the content of organic carbon. The contents of most of the listed trace elements in samples of bottom sediments on the standard section "Kola Meridian" in the Norwegian classification are consistent with background levels with the exception of Ni, Cr, and As. Their content in bottom sediments at some stations has met the criteria for "slight" and "moderate" pollution. The obtained results confirm the insignificant levels of contamination of bottom sediments of some trace elements. On the status of stocks of commercial species of aquatic biological resources, the observed levels of contamination of bottom sediments in the investigated areas of the Barents Sea will have no significant effect

Performance improvement inpolymer-based thin film transistor using modified bottom-contact structures with etched SiO{sub 2} layers

Energy Technology Data Exchange (ETDEWEB)

Park, Jeong Woo [R and D Center, Samsung Corning Precision Materials Co., Ltd, Asan (Korea, Republic of); You, Young Jun; Shim, Jae Won [Dept. of Electronics and Electrical Engineering, Dongguk University-Seoul, Seoul (Korea, Republic of)

2017-02-15

Polymer-based thin film transistors (TFTs) with a modified bottom-contact structure and etched SiO{sub 2} layer were developed and investigated. An increase in the field-effect mobility in the developed TFTs compared to TFTs with a normal bottom-contact structure was ascertained. A bottom-contact structure and the photolithographic processing method were used to ensure that the developed TFTs were suitable for commercial applications. Increased mobility of the modified bottom-contact structure was attributed to direct contact of the Au electrode with the active polymer layer.

Thermal shock behavior of toughened gadolinium zirconate/YSZ double-ceramic-layered thermal barrier coating

International Nuclear Information System (INIS)

Zhong, Xinghua; Zhao, Huayu; Zhou, Xiaming; Liu, Chenguang; Wang, Liang; Shao, Fang; Yang, Kai; Tao, Shunyan; Ding, Chuanxian

2014-01-01

Highlights: • Gd 2 Zr 2 O 7 /YSZ DCL thermal barrier coating was designed and fabricated. • The Gd 2 Zr 2 O 7 top ceramic layer was toughened by addition of nanostructured 3YSZ. • Remarkable improvement in thermal shock resistance of the DCL coating was achieved. - Abstract: Double-ceramic-layered (DCL) thermal barrier coating system comprising of toughened Gadolinium zirconate (Gd 2 Zr 2 O 7 , GZ) as the top ceramic layer and 4.5 mol% Y 2 O 3 partially-stabilized ZrO 2 (4.5YSZ) as the bottom ceramic layer was fabricated by plasma spraying and thermal shock behavior of the DCL coating was investigated. The GZ top ceramic layer was toughened by addition of nanostructured 3 mol% Y 2 O 3 partially-stabilized ZrO 2 (3YSZ) to improve fracture toughness of the matrix. The thermal shock resistance of the DCL coating was enhanced significantly compared to that of single-ceramic-layered (SCL) GZ-3YSZ composite coating, which is believed to be primarily attributed to the two factors: (i) the increase in fracture toughness of the top ceramic layer by incorporating nanostructured YSZ particles and (ii) the improvement in strain tolerance through the utilization of 4.5YSZ as the bottom ceramic layer. In addition, the failure mechanisms are mainly attributed to the still low fracture toughness of the top ceramic layer and oxidation of the bond-coat

Characterization of bottom ashes from coal pulverized power plants to determine their potential use feasibility

International Nuclear Information System (INIS)

Menendez, E.; Alvaro, A. M.; Argiz, C.; Parra, J. L.; Moragues, A.

2013-01-01

The disposal of coal by products represents environmental and economical problems around the world. Therefore, the reuse and valorisation of this waste has become an important issue in the last decades. While high-value construction products containing fly ash were developed and its use is actually totally accepted as an addition to cement, the use of the bottom ash as supplementary cementitious material has not been allow. This paper examines the chemical and physical properties of fly ashes and bottom ashes from two different coal power plants in order to compare them and analyse the potential feasibility of bottom ash as cement replacement. The mechanical properties of cement mortars made with different percentages of both ashes were also study. The results obtained showed similar chemical composition of both kinds of ashes. The compressive strength values of mortars with 10 % and 25 % of cement replacement (at 28 days) were above the limits established in European standards and there were not significant differences between fly ash and bottom ash from both origins. (Author)

Numerical Simulation Study on Steam-Assisted Gravity Drainage Performance in a Heavy Oil Reservoir with a Bottom Water Zone

Directory of Open Access Journals (Sweden)

Jun Ni

2017-12-01

Full Text Available In the Pikes Peak oil field near Lloydminster, Canada, a significant amount of heavy oil reserves is located in reservoirs with a bottom water zone. The properties of the bottom water zone and the operation parameters significantly affect oil production performance via the steam-assisted gravity drainage (SAGD process. Thus, in order to develop this type of heavy oil resource, a full understanding of the effects of these properties is necessary. In this study, the numerical simulation approach was applied to study the effects of properties in the bottom water zone in the SAGD process, such as the initial gas oil ratio, the thickness of the reservoir, and oil saturation of the bottom water zone. In addition, some operation parameters were studied including the injection pressure, the SAGD well pair location, and five different well patterns: (1 two corner wells, (2 triple wells, (3 downhole water sink well, (4 vertical injectors with a horizontal producer, and (5 fishbone well. The numerical simulation results suggest that the properties of the bottom water zone affect production performance extremely. First, both positive and negative effects were observed when solution gas exists in the heavy oil. Second, a logarithmical relationship was investigated between the bottom water production ratio and the thickness of the bottom water zone. Third, a non-linear relation was obtained between the oil recovery factor and oil saturation in the bottom water zone, and a peak oil recovery was achieved at the oil saturation rate of 30% in the bottom water zone. Furthermore, the operation parameters affected the heavy oil production performance. Comparison of the well patterns showed that the two corner wells and the triple wells patterns obtained the highest oil recovery factors of 74.71% and 77.19%, respectively, which are almost twice the oil recovery factors gained in the conventional SAGD process (47.84%. This indicates that the optimized SAGD process

Bottom-Up Tri-gate Transistors and Submicrosecond Photodetectors from Guided CdS Nanowalls.

Science.gov (United States)

Xu, Jinyou; Oksenberg, Eitan; Popovitz-Biro, Ronit; Rechav, Katya; Joselevich, Ernesto

2017-11-08

Tri-gate transistors offer better performance than planar transistors by exerting additional gate control over a channel from two lateral sides of semiconductor nanowalls (or "fins"). Here we report the bottom-up assembly of aligned CdS nanowalls by a simultaneous combination of horizontal catalytic vapor-liquid-solid growth and vertical facet-selective noncatalytic vapor-solid growth and their parallel integration into tri-gate transistors and photodetectors at wafer scale (cm 2 ) without postgrowth transfer or alignment steps. These tri-gate transistors act as enhancement-mode transistors with an on/off current ratio on the order of 10 8 , 4 orders of magnitude higher than the best results ever reported for planar enhancement-mode CdS transistors. The response time of the photodetector is reduced to the submicrosecond level, 1 order of magnitude shorter than the best results ever reported for photodetectors made of bottom-up semiconductor nanostructures. Guided semiconductor nanowalls open new opportunities for high-performance 3D nanodevices assembled from the bottom up.

How To Design A Triple Bottom Line Organization: A Start-Up Case Study

Directory of Open Access Journals (Sweden)

Bernhard Schroeder

2014-05-01

Full Text Available In today’s business environment, where success for a start-up company is measured by early revenue and profit, it can be quite challenging to design a triple bottom line organization (people/planet/profit from the very beginning. We present a case study of a U.S.-based start-up firm and discuss its early challenges, developmental processes, and current success as a triple bottom line firm. The company’s founder and CEO, with no initial product, distribution, or revenue strategy, sought to develop a company that could provide the marketplace with a valuable product while also staying true to a corporate vision of positively affecting less fortunate people. Our analysis of the case suggests that the founder’s vision, passion, transparent communication, and leveraging of partners’ resources were key elements in building the firm. We draw implications of our case study for the designers of future triple bottom line organizations.

The effect of bottom sediment supplement on heavy metals content in plants (Zea mays and soil

Directory of Open Access Journals (Sweden)

Baran A.

2013-04-01

Full Text Available Important aspect of bottom sediments is the problem of their management or disposal after their extraction from the bottom of rivers, dam reservoirs, ports, channels or ponds. The research aimed at an assessment of potential environmental management of bottom sediment used as an admixture to light soil basing on its effect on contents of heavy metals in plants and soil. The research was conducted on light soil with granulometric structure of weakly loamy sand. The bottom sediment was added to light soil in the amount of 0 (control 5, 10, 30 i 50%. The test plant was maize (Zea mays, “Bora” c.v. The sediment applied in the presented research revealed high share of silt and clay fractions, alkaline pH and low contents of heavy metals, therefore it may be used as an admixture to the above mentioned soils to improve their productivity. The applied bottom sediment to the soil affected a decreased in Zn, Cd and Pb content in maize in comparison with the treatment without the deposit whereas increased content of Cu, Cr and Ni. No exceeded permissible content of heavy metals concerning plant assessment in view of their forage usability were registered in maize biomass.

Iodine versus Bromine Functionalization for Bottom-Up Graphene Nanoribbon Growth

DEFF Research Database (Denmark)

Bronner, Christopher; Marangoni, Tomas; Rizzo, Daniel J.

2017-01-01

Deterministic bottom-up approaches for synthesizing atomically well-defined graphene nanoribbons (GNRs) largely rely on the surface-catalyzed activation of selected labile bonds in a molecular precursor followed by step-growth polymerization and cyclodehydrogenation. While the majority of success...

Definition and calculation of bottom quark cross-sections in deep-inelastic scattering at HERA and De termination of their uncertainties

Energy Technology Data Exchange (ETDEWEB)

Carli, T. E-mail: tancredi.carli@cern.ch; Chiochia, V.; Klimek, K

2003-09-01

The uncertainties involved in the calculation of bottom quark cross-sections in deep-inelastic scattering at HERA are studied in different phase space regions. Besides the inclusive bottom quark cross-section, definitions closer to the detector acceptance requiring at least one high energetic muon from the semi-leptonic bottom quark decay or a jet with high transverse energy are investigated. For each case the uncertainties due to the choice of the renormalisation and factorisation scale as well as the bottom quark mass are estimated in the perturbative NLO QCD calculation and furthermore uncertainties in the fragmentation of the bottom quark to a B-meson and in its semi-leptonic decay are discussed. (author)

Wave trapping by dual porous barriers near a wall in the presence of bottom undulation

Science.gov (United States)

Kaligatla, R. B.; Manisha; Sahoo, T.

2017-09-01

Trapping of oblique surface gravity waves by dual porous barriers near a wall is studied in the presence of step type varying bottom bed that is connected on both sides by water of uniform depths. The porous barriers are assumed to be fixed at a certain distance in front of a vertical rigid wall. Using linear water wave theory and Darcy's law for flow past porous structure, the physical problem is converted into a boundary value problem. Using eigenfunction expansion in the uniform bottom bed region and modified mild-slope equation in the varying bottom bed region, the mathematical problem is handled for solution. Moreover, certain jump conditions are used to account for mass conservation at slope discontinuities in the bottom bed profile. To understand the effect of dual porous barriers in creating tranquility zone and minimum load on the sea wall, reflection coefficient, wave forces acting on the barrier and the wall, and surface wave elevation are computed and analyzed for different values of depth ratio, porous-effect parameter, incident wave angle, gap between the barriers and wall and slope length of undulated bottom. The study reveals that with moderate porosity and suitable gap between barriers and sea wall, using dual barriers an effective wave trapping system can be developed which will exert less wave force on the barriers and the rigid wall. The proposed wave trapping system is likely to be of immense help for protecting various facilities/ infrastructures in coastal environment.

Wave Trapping by Dual Porous Barriers Near a Wall in the Presence of Bottom Undulation

Institute of Scientific and Technical Information of China (English)

R.B. Kaligatla; Manisha; T. Sahoo

2017-01-01

Trapping of oblique surface gravity waves by dual porous barriers near a wall is studied in the presence of step type varying bottom bed that is connected on both sides by water of uniform depths. The porous barriers are assumed to be fixed at a certain distance in front of a vertical rigid wall. Using linear water wave theory and Darcy's law for flow past porous structure, the physical problem is converted into a boundary value problem. Using eigenfunction expansion in the uniform bottom bed region and modified mild-slope equation in the varying bottom bed region, the mathematical problem is handled for solution. Moreover, certain jump conditions are used to account for mass conservation at slope discontinuities in the bottom bed profile. To understand the effect of dual porous barriers in creating tranquility zone and minimum load on the sea wall, reflection coefficient, wave forces acting on the barrier and the wall, and surface wave elevation are computed and analyzed for different values of depth ratio, porous-effect parameter, incident wave angle, gap between the barriers and wall and slope length of undulated bottom. The study reveals that with moderate porosity and suitable gap between barriers and sea wall, using dual barriers an effective wave trapping system can be developed which will exert less wave force on the barriers and the rigid wall. The proposed wave trapping system is likely to be of immense help for protecting various facilities/ infrastructures in coastal environment.

Reconstructing bottom water temperatures from measurements of temperature and thermal diffusivity in marine sediments

Science.gov (United States)

Miesner, F.; Lechleiter, A.; Müller, C.

2015-07-01

Continuous monitoring of oceanic bottom water temperatures is a complicated task, even in relatively easy-to-access basins like the North or Baltic seas. Here, a method to determine annual bottom water temperature variations from inverse modeling of instantaneous measurements of temperatures and sediment thermal properties is presented. This concept is similar to climate reconstructions over several thousand years from deep borehole data. However, in contrast, the presented method aims at reconstructing the recent temperature history of the last year from sediment thermal properties and temperatures from only a few meters depth. For solving the heat equation, a commonly used forward model is introduced and analyzed: knowing the bottom water temperature variations for the preceding years and the thermal properties of the sediments, the forward model determines the sediment temperature field. The bottom water temperature variation is modeled as an annual cosine defined by the mean temperature, the amplitude and a phase shift. As the forward model operator is non-linear but low-dimensional, common inversion schemes such as the Newton algorithm can be utilized. The algorithms are tested for artificial data with different noise levels and for two measured data sets: from the North Sea and from the Davis Strait. Both algorithms used show stable and satisfying results with reconstruction errors in the same magnitude as the initial data error. In particular, the artificial data sets are reproduced with accuracy within the bounds of the artificial noise level. Furthermore, the results for the measured North Sea data show small variances and resemble the bottom water temperature variations recorded from a nearby monitoring site with relative errors smaller than 1 % in all parameters.

Comparison between bottom-up and top-down approaches in the estimation of measurement uncertainty.

Science.gov (United States)

Lee, Jun Hyung; Choi, Jee-Hye; Youn, Jae Saeng; Cha, Young Joo; Song, Woonheung; Park, Ae Ja

2015-06-01

Measurement uncertainty is a metrological concept to quantify the variability of measurement results. There are two approaches to estimate measurement uncertainty. In this study, we sought to provide practical and detailed examples of the two approaches and compare the bottom-up and top-down approaches to estimating measurement uncertainty. We estimated measurement uncertainty of the concentration of glucose according to CLSI EP29-A guideline. Two different approaches were used. First, we performed a bottom-up approach. We identified the sources of uncertainty and made an uncertainty budget and assessed the measurement functions. We determined the uncertainties of each element and combined them. Second, we performed a top-down approach using internal quality control (IQC) data for 6 months. Then, we estimated and corrected systematic bias using certified reference material of glucose (NIST SRM 965b). The expanded uncertainties at the low glucose concentration (5.57 mmol/L) by the bottom-up approach and top-down approaches were ±0.18 mmol/L and ±0.17 mmol/L, respectively (all k=2). Those at the high glucose concentration (12.77 mmol/L) by the bottom-up and top-down approaches were ±0.34 mmol/L and ±0.36 mmol/L, respectively (all k=2). We presented practical and detailed examples for estimating measurement uncertainty by the two approaches. The uncertainties by the bottom-up approach were quite similar to those by the top-down approach. Thus, we demonstrated that the two approaches were approximately equivalent and interchangeable and concluded that clinical laboratories could determine measurement uncertainty by the simpler top-down approach.

High-frequency internal waves and thick bottom mixed layers observed by gliders in the Gulf Stream

Science.gov (United States)

Todd, Robert E.

2017-06-01

Autonomous underwater gliders are conducting high-resolution surveys within the Gulf Stream along the U.S. East Coast. Glider surveys reveal two mechanisms by which energy is extracted from the Gulf Stream as it flows over the Blake Plateau, a portion of the outer continental shelf between Florida and North Carolina where bottom depths are less than 1000 m. Internal waves with vertical velocities exceeding 0.1 m s-1 and frequencies just below the local buoyancy frequency are routinely found over the Blake Plateau, particularly near the Charleston Bump, a prominent topographic feature. These waves are likely internal lee waves generated by the subinertial Gulf Stream flow over the irregular bathymetry of the outer continental shelf. Bottom mixed layers with O(100) m thickness are also frequently encountered; these thick bottom mixed layers likely form in the lee of topography due to enhanced turbulence generated by O(1) m s-1 near-bottom flows.

Inversion for Sound Speed Profile by Using a Bottom Mounted Horizontal Line Array in Shallow Water

International Nuclear Information System (INIS)

Feng-Hua, Li; Ren-He, Zhang

2010-01-01

Ocean acoustic tomography is an appealing technique for remote monitoring of the ocean environment. In shallow water, matched field processing (MFP) with a vertical line array is one of the widely used methods for inverting the sound speed profile (SSP) of water column. The approach adopted is to invert the SSP with a bottom mounted horizontal line array (HLA) based on MFP. Empirical orthonormal functions are used to express the SSP, and perturbation theory is used in the forward sound field calculation. This inversion method is applied to the data measured in a shallow water acoustic experiment performed in 2003. Successful results show that the bottom mounted HLA is able to estimate the SSP. One of the most important advantages of the inversion method with bottom mounted HLA is that the bottom mounted HLA can keep a stable array shape and is safe in a relatively long period. (fundamental areas of phenomenology (including applications))

The Design of Drawing Process of Cylindrical Cup with Oval Bottom Using Computer Simulation

Directory of Open Access Journals (Sweden)

Kapustová Mária

2017-01-01

Full Text Available Based on technological calculations, technology of one-operation drawing without blankholder was designed for production of a large-dimensional drawpiece with shape of welded on concave bottom. The necessary drawing force was also defined by calculation as maximum drawing force for trimming of drawpiece bottom. This contribution points out to the importance of FEM simulation of drawing process in order to verify the design of production technology of drawpiece with shape of welded on concave bottom on the basis of technological calculations. Simulation programme Deform verified the construction design of drawing tool determined for drawpiece production by first draw, and also determined the drawing force actually consumed during plastic deformation of drawpiece shape. Used simulation software confirmed correctness of drawing tool construction, as correct material plastic flow in drawing tool was monitored and production of drawpiece was faultless.

Control strategy on the double-diffusive convection in a nanofluid layer with internal heat generation

Science.gov (United States)

Mokhtar, N. F. M.; Khalid, I. K.; Siri, Z.; Ibrahim, Z. B.; Gani, S. S. A.

2017-10-01

The influences of feedback control and internal heat source on the onset of Rayleigh-Bénard convection in a horizontal nanofluid layer is studied analytically due to Soret and Dufour parameters. The confining boundaries of the nanofluid layer (bottom boundary-top boundary) are assumed to be free-free, rigid-free, and rigid-rigid, with a source of heat from below. Linear stability theory is applied, and the eigenvalue solution is obtained numerically using the Galerkin technique. Focusing on the stationary convection, it is shown that there is a positive thermal resistance in the presence of feedback control on the onset of double-diffusive convection, while there is a positive thermal efficiency in the existence of internal heat generation. The possibilities of suppress or augment of the Rayleigh-Bénard convection in a nanofluid layer are also discussed in detail.

Bottom-up approach to sustainable urban development in Lebanon: The case of Zouk Mosbeh

OpenAIRE

El Asmar, Jean-Pierre; Ebohon, O. J.; Taki, A. H.

2012-01-01

In contrast with the “top-down” approach to development, the dominant methodology in Lebanon, Iemphasize rather the “bottom-up” approach where all stakeholders have equal opportunities to participate in policy formulation and implementation. The bottom-up or participatory approach to sustainable development has hardly been tested for urban development and management in Lebanon. This research concerns the sustainable rehabilitation of the built environment in the area of Zouk Mosbeh (ZM) in ...

Dissociable effects of top-down and bottom-up attention during episodic encoding

Science.gov (United States)

Uncapher, Melina R.; Hutchinson, J. Benjamin; Wagner, Anthony D.

2011-01-01

It is well established that the formation of memories for life’s experiences—episodic memory—is influenced by how we attend to those experiences, yet the neural mechanisms by which attention shapes episodic encoding are still unclear. We investigated how top-down and bottom-up attention contribute to memory encoding of visual objects in humans by manipulating both types of attention during functional magnetic resonance imaging (fMRI) of episodic memory formation. We show that dorsal parietal cortex—specifically, intraparietal sulcus (IPS)—was engaged during top-down attention and was also recruited during the successful formation of episodic memories. By contrast, bottom-up attention engaged ventral parietal cortex—specifically, temporoparietal junction (TPJ)—and was also more active during encoding failure. Functional connectivity analyses revealed further dissociations in how top-down and bottom-up attention influenced encoding: while both IPS and TPJ influenced activity in perceptual cortices thought to represent the information being encoded (fusiform/lateral occipital cortex), they each exerted opposite effects on memory encoding. Specifically, during a preparatory period preceding stimulus presentation, a stronger drive from IPS was associated with a higher likelihood that the subsequently attended stimulus would be encoded. By contrast, during stimulus processing, stronger connectivity with TPJ was associated with a lower likelihood the stimulus would be successfully encoded. These findings suggest that during encoding of visual objects into episodic memory, top-down and bottom-up attention can have opposite influences on perceptual areas that subserve visual object representation, suggesting that one manner in which attention modulates memory is by altering the perceptual processing of to-be-encoded stimuli. PMID:21880922

The influence of coal bottom ash and tincal (boron mineral) additions on the physical and microstructures of ceramic bodies

Energy Technology Data Exchange (ETDEWEB)

Bayca, S.U.; Batar, T.; Sayin, E.; Solak, O.; Kahraman, B. [Celal Bayar University, Manisa (Turkey). Soma Vocational School

2008-07-01

In this paper, the influence of coal bottom ash and tincal additions on the physical properties and microstructures of the standard wall tile body composition was investigated. Water absorption, fang strength, dry and fired shrinkage tests of the incorporated ceramic bodies and reference body were done. Microstructures of sintered tiles were analyzed using a scanning electron microscope (SEM). The results show that tincal additions to the ceramic body improved the physical properties of the tiles. As a result, tincal can be used as a flux material in the ceramic bodies due to its favorable effects on the water absorption and fired strength. The results revealed that bottom ash can be used in the ceramic tile body composition. When bottom ash was used in the ceramic industry, environmental hazards of bottom ash are inhibited. Furthermore, bottom ash is transformed to an economic product.

Resource partitioning within major bottom fish species in a highly productive upwelling ecosystem

Science.gov (United States)

Abdellaoui, Souad; El Halouani, Hassan; Tai, Imane; Masski, Hicham

2017-09-01

The Saharan Bank (21-26°N) is a wide subtropical continental shelf and a highly productive upwelling ecosystem. The bottom communities are dominated by octopus and sparid fish, which are the main targets of bottom-trawl fishing fleets. To investigate resource partitioning within the bottom fish community, adult fish from 14 of the most abundant species were investigated for stomach content analysis. Samples were collected during two periods: October 2003 and May 2007. The diet of the analysed species showed more variation between periods than between size classes, suggesting that temporal or spatial variability in prey availability appears to play a significant role in their diet. Multivariate analysis and subsequent clustering led to a grouping of the species within five trophic guilds. Two species were fish feeders, and the others mainly fed on benthic invertebrates, where epibenthic crustaceans, lamellibranchs and fish were the most important groups in defining trophic guilds. We found that the studied species had a high rate of overlapping spatial distributions and overlapping trophic niches. In this highly productive upwelling ecosystem, where food resources may not be a limiting factor, inter-specific competition did not appear to be an important factor in structuring bottom fish communities. For the species that showed differences in the proportions of prey categories in comparison with other ecosystems, the rise of the proportion of epibenthic crustaceans in their diet was a common feature; a possible consequence of the benthic productivity of this highly productive upwelling ecosystem.

Dynamics of fluctuations of Cs-137 contents in the bottom sediment in limnetic dam reservoir Goczalkowice

International Nuclear Information System (INIS)

Kwapulinski, J.; Majchrzyk, H.; Kalita, T.; Miroslawski, J.

1986-01-01

The results of 137 Cs studies in bottom sediment in the Goczalkowice reservoir are presented. The determined coefficients of aquatic migration, difusion in bottom sediment and water in vertical section confirm zonal nature of 137 Cs occurrance and accumulation in the reservoir. 5 refs., 1 fig., 6 tabs. (author)

Biomass gasification bottom ash as a source of CaO catalyst for biodiesel production via transesterification of palm oil

International Nuclear Information System (INIS)

Maneerung, Thawatchai; Kawi, Sibudjing; Wang, Chi-Hwa

2015-01-01

Highlights: • CaO catalyst was successfully developed from wood gasification bottom ash. • CaCO 3 in bottom ash can be converted to CaO catalyst by calcination. • CaO catalysts derived from bottom ash exhibited high activity towards transesterification. • CaO catalysts derived from bottom ash can be reutilized up to four times. - Abstract: The main aim of this research is to develop environmentally and economically benign heterogeneous catalysts for biodiesel production via transesterification of palm oil. For this propose, calcium oxide (CaO) catalyst has been developed from bottom ash waste arising from woody biomass gasification. Calcium carbonate was found to be the main component in bottom ash and can be transformed into the active CaO catalyst by simple calcination at 800 °C without any chemical treatment. The obtained CaO catalysts exhibit high biodiesel production activity, over 90% yield of methyl ester can be achieved at the optimized reaction condition. Experimental kinetic data fit well the pseudo-first order kinetic model. The activation energy (E a ) of the transesterification reaction was calculated to be 83.9 kJ mol −1 . Moreover, the CaO catalysts derived from woody biomass gasification bottom ash can be reutilized up to four times, offering the efficient and low-cost CaO catalysts which could make biodiesel production process more economic and environmental friendly

Bottom-up approach for carbon nanotube interconnects

International Nuclear Information System (INIS)

Li Jun; Ye Qi; Cassell, Alan; Ng, Hou Tee; Stevens, Ramsey; Han Jie; Meyyappan, M.

2003-01-01

We report a bottom-up approach to integrate multiwalled carbon nanotubes (MWNTs) into multilevel interconnects in silicon integrated-circuit manufacturing. MWNTs are grown vertically from patterned catalyst spots using plasma-enhanced chemical vapor deposition. We demonstrate the capability to grow aligned structures ranging from a single tube to forest-like arrays at desired locations. SiO 2 is deposited to encapsulate each nanotube and the substrate, followed by a mechanical polishing process for planarization. MWNTs retain their integrity and demonstrate electrical properties consistent with their original structure

Experimental and Numerical Investigations of Applying Tip-bottomed Tool for Bending Advanced Ultra-high Strength Steel Sheet

Science.gov (United States)

Mitsomwang, Pusit; Borrisutthekul, Rattana; Klaiw-awoot, Ken; Pattalung, Aran

2017-09-01

This research was carried out aiming to investigate the application of a tip-bottomed tool for bending an advanced ultra-high strength steel sheet. The V-die bending experiment of a dual phase steel (DP980) sheet which had a thickness of 1.6 mm was executed using a conventional bending and a tip-bottomed punches. Experimental results revealed that the springback of the bent worksheet in the case of the tip-bottomed punch was less than that of the conventional punch case. To further discuss bending characteristics, a finite element (FE) model was developed and used to simulate the bending of the worksheet. From the FE analysis, it was found that the application of the tip-bottomed punch contributed the plastic deformation to occur at the bending region. Consequently, the springback of the worksheet reduced. In addition, the width of the punch tip was found to affect the deformation at the bending region and determined the springback of the bent worksheet. Moreover, the use of the tip-bottomed punch resulted in the apparent increase of the surface hardness of the bent worksheet, compared to the bending with the conventional punch.

Distribution of 137Cs in samples of ocean bottom sediments of the baltic sea in 1982-1983

International Nuclear Information System (INIS)

Gedenov, L.I.; Flegontov, V.M.; Ivanova, L.M.; Kostandov, K.A.

1986-01-01

The concentration of Cs-137 in samples of ocean bottom sediments picked up in 1979 in the Gulf of Finland with a geological nozzle pipe varied within a wide interval of values. The results could indicate nonuniformity of the Cs-137 distribution in ocean bottom sediments as well as the penetration of significant amounts of Cs-137 to large depths. The main error resulted from the sampling technique employed because the upper part of the sediment could be lost. In 1982, a special ground-sampling device, with which the upper layer of sediments in the water layer close to the ocean bottom could be sampled, was tested in the Gulf of Finland and the Northeastern part of the Baltic Sea. The results of a layerwise determination of the Cs-137 concentration in samples of ocean bottom sediments of the Gulf of Finland and of the Baltic Sea are listed. The new soil-sampling device for picking samples of ocean sediments of undisturbed stratification will allow a correct determination of the radionuclide accumulation in the upper layers of ocean bottom sediments in the Baltic Sea

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1986-01-01

Recent work by Phillips and Selby has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. In some instances an influence diagram can be used as a graphical representation of probabilistic dependence within a system or event sequence. Under these circumstances, Bayesian statistics is employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g. the top node). Top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. The purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies

Chloride leaching from municipal solid waste incineration (MSWI) bottom ash

NARCIS (Netherlands)

Alam, Q.; Schollbach, K.; Florea, M.V.A.; Brouwers, H.J.H.; Vlastimil, Bilek; Kersner, Zbynek; Simonova, Hana

2017-01-01

The presence of chlorides in the Municipal Solid Waste Incineration bottom ashes (BA) hinders their potential for recycling in building materials. The contaminant content in the incineration residues is strictly regulated by the Dutch legislation Soil Quality Decree (2013). The fine fraction

Analyzing Double Image Illusion through Double Indiscernibility and Lattice Theory

Directory of Open Access Journals (Sweden)

Kohei Sonoda

2011-10-01

Full Text Available The figure-ground division plays a fundamental role in all image perceptions. Although there are a lot of studies about extraction of a figure such as detection of edges or grouping of texture, there are few discussions about a relationship between obtained figure and ground. We focused on double image illusions having two complementary relationships be- tween figure and ground and analyzed them. We divided the double image illusions according to two different interpretations and using these divisions we extracted and analyzed their logical structures by lattices derived from rough sets that we had developed. As a result we discovered unusual logical structures in double image illusions.

Experimental investigation of slamming impact acted on flat bottom bodies and cumulative damage

Directory of Open Access Journals (Sweden)

Hyunkyoung Shin

2018-05-01

Full Text Available Most offshore structures including offshore wind turbines, ships, etc. suffer from the impulsive pressure loads due to slamming phenomena in rough waves. The effects of elasticity & plasticity on such slamming loads are investigated through wet free drop test results of several steel unstiffened flat bottom bodies in the rectangular water tank. Also, their cumulative deformations by consecutively repetitive free drops from 1000 mm to 2000 mm in height are measured. Keywords: Slamming phenomena, Impulsive pressure load, Wet free drop test, Flat bottom body, Cumulative damage

Sieving of municipal solid waste incineration (MSWI) bottom ash; Siktning av askor fraan avfallsfoerbraenning

Energy Technology Data Exchange (ETDEWEB)

Todorovic, Jelena

2010-07-01

Waste-to-Energy is steadily increasing in Sweden and more than 46 % of municipal solid waste (MSW) is being incinerated. Solid residues from MSW incineration (MSWI) mainly constitute of bottom ash and air pollution control (APC) residues. Bottom ashes from MSWI amounted to 0.7 millions of tons and APC residues to 0.2 millions of tons in 2008. Bottom ashes from MSWI contain pollutants like metals (e.g. Pb, Zn, Cu), metalloids (e.g. As, Se), elements forming oxyanions (e.g. Sb, Cr, Mo) and easily soluble salts like chlorides and sulphates. These constituents can leach out polluting the environment if ash comes in contact with water. Treatment methods for decreasing the amount of pollutants in ashes or their mobility are therefore needed. Sieving was investigated as a separate or a complementary treatment method for MSWI ashes. Hypothesis was that the large share of pollutant concentrations could be removed from the ashes through separation of the finest fractions. The rest is less harmful to the environment, more acceptable as secondary construction material or less costly to landfill. Investigation included three MSWI ashes, namely bottom ash from Boraas Energy och Miljoe's plant with fluid bad, boiler ash from the same plant and bottom ash from Renova's stocker grate type plant. Ashes were sieved in 2-4 size fractions. Total content of pollutants and their leachability (batch leaching test, L/S=10 l/kg) was assessed for each of the fractions. Leaching results were compared to limit values stipulated by Swedish Environmental Protection Agency for acceptance of waste at landfills as wells as to recommendations for reuse of waste as a construction material. Results from bottom ash from the stocker grate type incinerator and from the boiler ash confirm the hypothesis that pollutants leach out in higher concentrations from the finer fractions. A large amount of pollutant could be removed from the ashes through sieving, but the goal to produce a fraction that

Thermodynamic analysis of the effect of channel geometry on heat transfer in double-layered microchannel heat sinks

International Nuclear Information System (INIS)

Zhai, Yuling; Li, Zhouhang; Wang, Hua; Xu, Jianxin

2017-01-01

Highlights: • A novel geometry with rectangular and complex channels in each layer is presented. • It shows lower pressure drop and more uniform temperature distribution. • The essence of enhanced heat transfer is analyzed from thermodynamics. - Abstract: Novel double-layered microchannel heat sinks with different channel geometries in each layer (Structure 2 for short) are designed to reduce pressure drop and maintain good heat transfer performance, which is compared with structure 1 (the same of complex channel geometry in each layer). The effect of parallel flow, counter flow and different channel geometries on heat transfer is studied numerically. Moreover, the essence of heat transfer enhancement is analyzed by thermodynamics. On one hand, the synergy relationship between flow field and temperature field is analyzed by field synergy principle. On the other hand, the irreversibility of heat transfer is studied by transport efficiency of thermal energy. The results show that the temperature distribution of counter flow is more uniform than that of parallel flow. Furthermore, heat dissipation and pressure drop of structure 2 are both better and lower than that of structure 1. Form the viewpoint of temperature distribution, structure C2 (i.e., counter flow with rectangular channels in upper layer and complex channels in bottom layer) presents the most uniform bottom temperature for microelectronic cooling. However, comprehensive heat transfer performance of structure P2 (i.e., parallel flow with rectangular channels in upper layer and complex channels in bottom layer) shows the best from the viewpoint of thermodynamics. The reasons can be ascribed to the channel geometry of structure P2 can obviously improve the synergy relationship between temperature and velocity fields, reduce fluid temperature gradient and heat transfer irreversibility.

Influence of break structures on the distribution of radionuclides in bottom sediments of the Kyiv reservoir

International Nuclear Information System (INIS)

Shestopalov, V.M.; Lyal'ko, V.I.; Fedorovskij, A.D.; Sirenko, L.A.; Khodorovskij, A.Ya.

2000-01-01

We study the distribution of radionuclides in bottom sediments of the Kyiv reservoir on the basis of research of adjacent territory break - block structures with deciphering space-born images and ground measurements and forecast the occurrence of extreme situations due to the redistribution of bottom water flows and sediments of radionuclides

The bottom water exchange between the Singapore Strait and the West Johor Strait

Science.gov (United States)

Sun, Yunfang; Eltahir, Elfatih; Malanotte-Rizzoli, Paola

2017-08-01

As a part of the border between Singapore and Malaysia, the West Johor Strait (WJS) suffered newly from harmful algal blooms. There is no previous study showing the source of the nutrients in the WJS. This paper is investigating the possible water exchange between the water in the WJS and the bottom water in Singapore Strait. This paper adopts a two-level nesting atmosphere-ocean coupled models to downscale the global atmosphere-ocean model into the Singapore coastal water, keeping the large-scale and long-term ocean and climate circulation signals and the advantages of the high-resolution. Based on the high-resolution ocean circulation fields, a Lagrangian particle tracking model is used to trace the Singapore Strait's bottom water movement and the water mixing in the WJS. The results showed that the numerical models well resolved the Singapore coastal water regional circulation. There is a small but significant bottom water (1.25%) transport from the Singapore Strait to the WJS, which occurs from the southwest coastline of Singapore. The bottom water in the Singapore Strait prefers to enter the WJS during the spring tide and the flood period, and stay in Johor Strait for 6.4 days. The spring tide is the first-order factor for the water vertical mixing in the WJS, the wind is also very important for the vertical mixing especially in neap tide condition. An overall very important factor is the light perturbation. With the strongest vertical mixing of nutrients and bottom sediments due to the spring tide, the latter ones may inhibit the light penetration during the spring tide and reduce the algal bloom. The light penetration otherwise is greater during the neap tide, when the winds are the most important factor and hence favor the algal bloom. With the strongest wind in February and the longest permanence time in June and the sufficient nutrient supply in February and June, the most serious algal blooms may happen in February and June in the WJS.

An experimental study on the hazard assessment and mechanical properties of porous concrete utilizing coal bottom ash coarse aggregate in Korea.

Science.gov (United States)

Park, Seung Bum; Jang, Young Il; Lee, Jun; Lee, Byung Jae

2009-07-15

This study evaluates quality properties and toxicity of coal bottom ash coarse aggregate and analyzes mechanical properties of porous concrete depending on mixing rates of coal bottom ash. As a result, soundness and resistance to abrasion of coal bottom ash coarse aggregate were satisfied according to the standard of coarse aggregate for concrete. To satisfy the standard pertaining to chloride content, the coarse aggregates have to be washed more than twice. In regards to the result of leaching test for coal bottom ash coarse aggregate and porous concrete produced with these coarse aggregates, it was satisfied with the environment criteria. As the mixing rate of coal bottom ash increased, influence of void ratio and permeability coefficient was very little, but compressive and flexural strength decreased. When coal bottom ash was mixed over 40%, strength decreased sharply (compressive strength: by 11.7-27.1%, flexural strength: by maximum 26.4%). Also, as the mixing rate of coal bottom ash increased, it was confirmed that test specimens were destroyed by aggregate fracture more than binder fracture and interface fracture. To utilize coal bottom ash in large quantities, it is thought that an improvement method in regards to strength has to be discussed such as incorporation of reinforcing materials and improvement of aggregate hardness.

Nanomaterial processing using self-assembly-bottom-up chemical and biological approaches

International Nuclear Information System (INIS)

Thiruvengadathan, Rajagopalan; Gangopadhyay, Keshab; Gangopadhyay, Shubhra; Korampally, Venumadhav; Ghosh, Arkasubhra; Chanda, Nripen

2013-01-01

Nanotechnology is touted as the next logical sequence in technological evolution. This has led to a substantial surge in research activities pertaining to the development and fundamental understanding of processes and assembly at the nanoscale. Both top-down and bottom-up fabrication approaches may be used to realize a range of well-defined nanostructured materials with desirable physical and chemical attributes. Among these, the bottom-up self-assembly process offers the most realistic solution toward the fabrication of next-generation functional materials and devices. Here, we present a comprehensive review on the physical basis behind self-assembly and the processes reported in recent years to direct the assembly of nanoscale functional blocks into hierarchically ordered structures. This paper emphasizes assembly in the synthetic domain as well in the biological domain, underscoring the importance of biomimetic approaches toward novel materials. In particular, two important classes of directed self-assembly, namely, (i) self-assembly among nanoparticle–polymer systems and (ii) external field-guided assembly are highlighted. The spontaneous self-assembling behavior observed in nature that leads to complex, multifunctional, hierarchical structures within biological systems is also discussed in this review. Recent research undertaken to synthesize hierarchically assembled functional materials have underscored the need as well as the benefits harvested in synergistically combining top-down fabrication methods with bottom-up self-assembly. (review article)

Retention and leaching of nitrite by municipal solid waste incinerator bottom ash under the landfill circumstance.

Science.gov (United States)

Yao, Jun; Kong, Qingna; Zhu, Huayue; Long, Yuyang; Shen, Dongsheng

2015-01-01

The retention and leaching of nitrite by municipal solid waste incinerator (MSWI) bottom ash could affect its migration in the landfill. In this study, the effect of the dosage of MSWI bottom ash as well as the variation of the landfill environmental parameters including pH, anions and organic matter on the nitrite retention and leaching behavior was investigated by batch experiments. The highest removal percentage (73.0%) of nitrite was observed when the dosage of MSWI bottom ash was 10 g L(-1) in 2 mg L(-1) nitrite solution. Further increase of the dosage would retard the retention, as the nitrite leaching from MSWI bottom ash was enhanced. The optimum retention of nitrite was observed when the pH was 5.0, while the leaching of nitrite showed a consistent reduction with the increase of pH. Besides, the presence of Cl(-), SO4(2)(-) and acetic acid could enhance the leaching of nitrite and mitigate the retention process. However, the retention of nitrite was enhanced by PO4(3)(-), which was probably due to the formation of the apatite, an active material for the adsorption of the nitrite. These results suggested that MSWI bottom ash could affect the migration of nitrite in the landfill, which was related to the variation of the landfill circumstance. Copyright © 2014 Elsevier Ltd. All rights reserved.

Specific expression of the vacuolar iron transporter, TgVit, causes iron accumulation in blue-colored inner bottom segments of various tulip petals.

Science.gov (United States)

Momonoi, Kazumi; Tsuji, Toshiaki; Kazuma, Kohei; Yoshida, Kumi

2012-01-01

Several flowers of Tulipa gesneriana exhibit a blue color in the bottom segments of the inner perianth. We have previously reported the inner-bottom tissue-specific iron accumulation and expression of the vacuolar iron transporter, TgVit1, in tulip cv. Murasakizuisho. To clarify whether the TgVit1-dependent iron accumulation and blue-color development in tulip petals are universal, we analyzed anthocyanin, its co-pigment components, iron contents and the expression of TgVit1 mRNA in 13 cultivars which show a blue color in the bottom segments of the inner perianth accompanying yellow- and white-colored inner-bottom petals. All of the blue bottom segments contained the same anthocyanin component, delphinidin 3-rutinoside. The flavonol composition varied with cultivar and tissue part. The major flavonol in the bottom segments of the inner perianth was rutin. The iron content in the upper part was less than that in the bottom segments of the inner perianth. The iron content in the yellow and white petals was higher in the bottom segment of the inner perianth than in the upper tissues. TgVit1 mRNA expression was apparent in all of the bottom tissues of the inner perianth. The result of a reproduction experiment by mixing the constituents suggests that the blue coloration in tulip petals is generally caused by iron complexation to delphinidin 3-rutinoside and that the iron complex is solubilized and stabilized by flavonol glycosides. TgVit1-dependent iron accumulation in the bottom segments of the inner perianth might be controlled by an unknown system that differentiated the upper parts and bottom segments of the inner perianth.

Properties and Leachability of Self-Compacting Concrete Incorporated with Fly Ash and Bottom Ash

Science.gov (United States)

Kadir, Aeslina Abdul; Ikhmal Haqeem Hassan, Mohd; Jamaluddin, Norwati; Bakri Abdullah, Mohd Mustafa Al

2016-06-01

The process of combustion in coal-fired power plant generates ashes, namely fly ash and bottom ash. Besides, coal ash produced from coal combustion contains heavy metals within their compositions. These metals are toxic to the environment as well as to human health. Fortunately, treatment methods are available for these ashes, and the use of fly ash and bottom ash in the concrete mix is one of the few. Therefore, an experimental program was carried out to study the properties and determine the leachability of selfcompacting concrete incorporated with fly ash and bottom ash. For experimental study, self-compacting concrete was produced with fly ash as a replacement for Ordinary Portland Cement and bottom ash as a replacement for sand with the ratios of 10%, 20%, and 30% respectively. The fresh properties tests conducted were slump flow, t500, sieve segregation and J-ring. Meanwhile for the hardened properties, density, compressive strength and water absorption test were performed. The samples were then crushed to be extracted using Toxicity Characteristic Leaching Procedure and heavy metals content within the samples were identified accordingly using Atomic Absorption Spectrometry. The results demonstrated that both fresh and hardened properties were qualified to categorize as self-compacting concrete. Improvements in compressive strength were observed, and densities for all the samples were identified as a normal weight concrete with ranges between 2000 kg/m3 to 2600 kg/m3. Other than that, it was found that incorporation up to 30% of the ashes was safe as the leached heavy metals concentration did not exceed the regulatory levels, except for arsenic. In conclusion, this study will serve as a reference which suggests that fly ash and bottom ash are widely applicable in concrete technology, and its incorporation in self-compacting concrete constitutes a potential means of adding value to appropriate mix and design.

Rapid bottom melting widespread near Antarctic ice sheet grounding lines

Science.gov (United States)

Rignot, E.; Jacobs, S.

2002-01-01

As continental ice from Antartica reaches the grounding line and begins to float, its underside melts into the ocean. Results obtained with satellite radar interferometry reveal that bottom melt rates experienced by large outlet glaciers near their grounding lines are far higher than generally assumed.

Bottom-up laboratory testing of the DKIST Visible Broadband Imager (VBI)

Science.gov (United States)

Ferayorni, Andrew; Beard, Andrew; Cole, Wes; Gregory, Scott; Wöeger, Friedrich

2016-08-01

The Daniel K. Inouye Solar Telescope (DKIST) is a 4-meter solar observatory under construction at Haleakala, Hawaii [1]. The Visible Broadband Imager (VBI) is a first light instrument that will record images at the highest possible spatial and temporal resolution of the DKIST at a number of scientifically important wavelengths [2]. The VBI is a pathfinder for DKIST instrumentation and a test bed for developing processes and procedures in the areas of unit, systems integration, and user acceptance testing. These test procedures have been developed and repeatedly executed during VBI construction in the lab as part of a "test early and test often" philosophy aimed at identifying and resolving issues early thus saving cost during integration test and commissioning on summit. The VBI team recently completed a bottom up end-to-end system test of the instrument in the lab that allowed the instrument's functionality, performance, and usability to be validated against documented system requirements. The bottom up testing approach includes four levels of testing, each introducing another layer in the control hierarchy that is tested before moving to the next level. First the instrument mechanisms are tested for positioning accuracy and repeatability using a laboratory position-sensing detector (PSD). Second the real-time motion controls are used to drive the mechanisms to verify speed and timing synchronization requirements are being met. Next the high-level software is introduced and the instrument is driven through a series of end-to-end tests that exercise the mechanisms, cameras, and simulated data processing. Finally, user acceptance testing is performed on operational and engineering use cases through the use of the instrument engineering graphical user interface (GUI). In this paper we present the VBI bottom up test plan, procedures, example test cases and tools used, as well as results from test execution in the laboratory. We will also discuss the benefits realized

Combined effect of bottom reflectivity and water turbidity on steady state thermal efficiency of salt gradient solar pond

International Nuclear Information System (INIS)

Husain, M.; Patil, P.S.; Patil, S.R.; Samdarshi, S.K.

2004-01-01

In salt gradient solar ponds, the clarity of water and absorptivity of the bottom are important concerns. However, both are practically difficult to maintain beyond a certain limit. The reflectivity of the bottom causes the loss of a fraction of the incident radiation flux, resulting in lower absorption of flux in the pond. Turbidity hinders the propagation of radiation. Thereby it decreases the flux reaching the storage zone. Both these factors lower the efficiency of the pond significantly. However, the same turbidity also prevents the loss of radiation reflected from the bottom. Hence, the combined effect is compensatory to some extent. The present work is an analysis of the combined effect of the bottom's reflectivity and water turbidity on the steady state efficiency of solar ponds. It is found that in the case of a reflective bottom, turbidity, within certain limits, improves the efficiency of pond. This is apparently contradictory to the conventional beliefs about the pond. Nevertheless, this conclusion is of practical importance for design and maintenance of solar ponds

Relative importance of plant-mediated bottom-up and top-down forces on herbivore abundance on Brassica oleracea

NARCIS (Netherlands)

Kos, M.; Broekgaarden, C.; Kabouw, P.; Oude Lenferink, K.; Poelman, E.H.; Vet, L.E.M.; Dicke, M.; Loon, van J.J.A.

2011-01-01

1. Arthropod communities are structured by complex interactions between bottom-up (resource-based) and top-down (natural enemy-based) forces. Their relative importance in shaping arthropod communities, however, continues to be under debate. Bottom-up and top-down forces can be affected by

Bottom nozzle of a LWR fuel assembly

International Nuclear Information System (INIS)

Leroux, J.C.

1991-01-01

The bottom nozzle consists of a transverse element in form of box having a bending resistant grid structure which has an outer peripheral frame of cross-section corresponding to that of the fuel assembly and which has walls defining large cells. The transverse element has a retainer plate with a regular array of openings. The retainer plate is fixed above and parallel to the grid structure with a spacing in order to form, between the grid structure and the retainer plate a free space for tranquil flow of cooling water and for debris collection [fr

Rankine bottoming cycle safety analysis. Final report

Energy Technology Data Exchange (ETDEWEB)

Lewandowski, G.A.

1980-02-01

Vector Engineering Inc. conducted a safety and hazards analysis of three Rankine Bottoming Cycle Systems in public utility applications: a Thermo Electron system using Fluorinal-85 (a mixture of 85 mole % trifluoroethanol and 15 mole % water) as the working fluid; a Sundstrand system using toluene as the working fluid; and a Mechanical Technology system using steam and Freon-II as the working fluids. The properties of the working fluids considered are flammability, toxicity, and degradation, and the risks to both plant workers and the community at large are analyzed.

SOFIA - A simulation tool for bottom founded and floating offshore structures

DEFF Research Database (Denmark)

Nielsen, Morten Eggert; Ulriksen, Martin Dalgaard; Damkilde, Lars

2017-01-01

This paper presents a recently developed simulation tool, SOFIA (Simulation Of Floaters In Action), suitable for modeling slender bottom founded and moored/freely floating space frame structures exposed to environmental loads. In contrast to traditional rigid body formulations of floating...... and structure domains, which are coupled through the structural equation of motion. The structural domain is handled by means of the finite element method, while large displacements and stress stiffening effects, exhibited by moored floating structures, are inherently included due to a co-rotational element...... formulation. The fluid domain is modeled by an appropriate water wave theory, and the hydrodynamic loads are evaluated at the instantaneous fluid-structure interface by means of a relative Morison equation. The equation of motion is solved in time domain, which makes SOFIA capable of handling bottom founded...

Report of the Committee on the Survey of Hull Bottom of Nuclear Ship Mutsu

International Nuclear Information System (INIS)

1979-01-01

The nuclear ship Mutsu arrived the Sasebo Shipyard, Sasebo Heavy Industries Co., Ltd., in October, 1978, to repair the shielding for the reactor and to inspect generally the safety. The docking works were not carried out since 1972 for the Mutsu, therefore it was decided to admit the Mutsu in a dock to put the hull in order. To prepare for starting the output test again, it is necessary to grasp the state of the hull part below water line and take appropriate measures as occasions demand, therefore the Japan Nuclear Ship Development Agency established the Committee on the Survey of Hull Bottom of Nuclear Ship Mutsu in July, 1979. Three meetings of the committee were held from July 2 to September 19, and the draft of the report was drawn up. The Mutsu entered No. 5 dock of the Sasebo Shipyard on July 9, and left on July 23, and the survey of the hull bottom was carried out during that period. The results of the survey are reported as follows: the state of bottom shell plates, the state of aft part and the propeller, the state of sea chests, the state of the electrical corrosion protection of bottom shell plates and the state of sea valves. The problem to be specially mentioned was not found, and it was recognized that the sound maintenance has been carried out. (Kako, I.)

Characteristics of low-frequency components of the near-bottom current in the Chinese Pioneer Area

Institute of Scientific and Technical Information of China (English)

LIANG Chujin; HOU Yijun; CHEN Qi; DONG Ruzhou; DONG Lixian

2004-01-01

Two deep-sea moorings were deployed respectively in the east area and the west area of Chinese Pioneer Area (CPA) in the tropic east Pacific to monitor the regional deep-sea dynamics below 600 meters above bottom (mab) from July 1997 to Oct. 1999. Results of statistics, spectral estimate and correlation analysis of the low-passed velocity data show that time scales of low-frequency components of the near-bottom currents are 25~120 days, in which 51-day period dominates the lower band of the frequency domain. Topographic features have obvious effect on low-frequency currents below 50 mab; modulations of the bottom-intensified sheared mean flow to the low-frequency currents are the dynamic mechanism of the frequency shift that occurs in both the east-area and the west-area.

Identifying prognostic features by bottom-up approach and correlating to drug repositioning.

Directory of Open Access Journals (Sweden)

Wei Li

Full Text Available Traditionally top-down method was used to identify prognostic features in cancer research. That is to say, differentially expressed genes usually in cancer versus normal were identified to see if they possess survival prediction power. The problem is that prognostic features identified from one set of patient samples can rarely be transferred to other datasets. We apply bottom-up approach in this study: survival correlated or clinical stage correlated genes were selected first and prioritized by their network topology additionally, then a small set of features can be used as a prognostic signature.Gene expression profiles of a cohort of 221 hepatocellular carcinoma (HCC patients were used as a training set, 'bottom-up' approach was applied to discover gene-expression signatures associated with survival in both tumor and adjacent non-tumor tissues, and compared with 'top-down' approach. The results were validated in a second cohort of 82 patients which was used as a testing set.Two sets of gene signatures separately identified in tumor and adjacent non-tumor tissues by bottom-up approach were developed in the training cohort. These two signatures were associated with overall survival times of HCC patients and the robustness of each was validated in the testing set, and each predictive performance was better than gene expression signatures reported previously. Moreover, genes in these two prognosis signature gave some indications for drug-repositioning on HCC. Some approved drugs targeting these markers have the alternative indications on hepatocellular carcinoma.Using the bottom-up approach, we have developed two prognostic gene signatures with a limited number of genes that associated with overall survival times of patients with HCC. Furthermore, prognostic markers in these two signatures have the potential to be therapeutic targets.

Project Half Double

DEFF Research Database (Denmark)

Svejvig, Per; Ehlers, Michael; Adland, Karoline Thorp

activities carried out within the framework of the projects. The formal part of Project Half Double was initiated in June 2015. We started out by developing, refining and testing the Half Double methodology on seven pilot projects in the first phase of the project, which will end June 2016. The current......Project Half Double has a clear mission to succeed in finding a project methodology that can increase the success rate of our projects while increasing the speed at which we generate new ideas and develop new products and services. Chaos and complexity should be seen as a basic condition...... and as an opportunity rather than a threat and a risk. We are convinced that by doing so, we can strengthen Denmark’s competitiveness and play an important role in the battle for jobs and future welfare. The overall goal is to deliver “projects in half the time with double the impact”, where projects in half the time...

Project Half Double

DEFF Research Database (Denmark)

Svejvig, Per; Gerstrøm, Anna; Frederiksen, Signe Hedeboe

The Half Double mission: Project Half Double has a clear mission. We want to succeed in finding a project methodology that can increase the success rate of our projects while increasing the development speed of new products and services. We are convinced that by doing so we can strengthen...... the competitiveness of Denmark and play an important role in the battle for jobs and future welfare. The overall goal is to deliver “Projects in half the time with double the impact” where projects in half the time should be understood as half the time to impact (benefit realization, effect is achieved......) and not as half the time for project execution. The Half Double project journey: It all began in May 2013 when we asked ourselves: How do we create a new and radical project paradigm that can create successful projects? Today we are a movement of hundreds of passionate project people, and it grows larger...

The Study on Stability and Seakeeping Characteristics of the Glass Bottom Boat Trimaran in Karimunjawa Island

Science.gov (United States)

Arswendo Adietya, Berlian; Windyandari, Aulia; Fauzan Zakki, Ahmad

2018-03-01

Recently the diversity of fish populations in the waters Karimunjawa Island is only appreciated by those who have the ability to play diving and snorkeling. It is due to the unavailability of a vehicle that is specially made to delight in the fascination of the underwater panorama. One of the alternative solutions is using the glass bottom boat technology which is using transparent bottom that might look out the underwater scenery instead of swimming and snorkeling. The paper has focused on the study of intact stability and seakeeping characteristics of glass bottom boat trimaran in Karimunjawa Island. The intact stability characteristics will be investigated at the various load cases and weight distribution configurations which are influenced by the passenger positions and fuel tank condition. Regarding the seakeeping performance analysis, the ITTC-Bretschneider will be adopted as the wave spectrum at the wave parameters defined from the operational environment. The influence of the parameters on the stability and seakeeping of the glass bottom boat trimaran are presented and discussed.

Conditions for the occurrence of intense turbidity currents in the benthic boundary layer over a sloping bottom

NARCIS (Netherlands)

Zhmur, VV

2003-01-01

The evolution of density currents over the continental slope of the ocean is investigated with allowance for the entrainment of the bottom sediments and background liquid in motion. A simple criterion is proposed for determining the possibility of evolving initially weak density currents into bottom

Cascadia Initiative Ocean Bottom Seismograph Performance

Science.gov (United States)

Evers, B.; Aderhold, K.

2017-12-01

The Ocean Bottom Seismograph Instrument Pool (OBSIP) provided instrumentation and operations support for the Cascadia Initiative community experiment. This experiment investigated geophysical processes across the Cascadia subduction zone through a combination of onshore and offshore seismic data. The recovery of Year 4 instruments in September 2015 marked the conclusion of a multi-year experiment that utilized 60 ocean-bottom seismographs (OBSs) specifically designed for the subduction zone boundary, including shallow/deep water deployments and active fisheries. The new instruments featured trawl-resistant enclosures designed by Lamont-Doherty Earth Observatory (LDEO) and Scripps Institution of Oceanography (SIO) for shallow deployment [water depth ≤ 500 m], as well as new deep-water instruments designed by Woods Hole Oceanographic Institute (WHOI). Existing OBSIP instruments were also deployed along the Blanco Transform Fault and on the Gorda Plate through complementary experiments. Station instrumentation included weak and strong motion seismometers, differential pressure gauges (DPG) and absolute pressure gauges (APG). All data collected from the Cascadia, Blanco, and Gorda deployments is available through the Incorporated Research Institutions for Seismology (IRIS) Data Management Center (DMC). The Cascadia Initiative is the largest amphibious seismic experiment undertaken to date, encompassing a diverse technical implementation and demonstrating an effective structure for community experiments. Thus, the results from Cascadia serve as both a technical and operational resource for the development of future community experiments, such as might be contemplated as part of the SZ4D Initiative. To guide future efforts, we investigate and summarize the quality of the Cascadia OBS data using basic metrics such as instrument recovery and more advanced metrics such as noise characteristics through power spectral density analysis. We also use this broad and diverse

Double parton scattering in the ultraviolet. Addressing the double counting problem

Energy Technology Data Exchange (ETDEWEB)

Diehl, Markus [Deutsches Elektronen-Synchrotron (DESY), Hamburg (Germany); Gaunt, Jonathan R. [Nikhef Theory Group, Amsterdam (Netherlands); Amsterdam VU Univ. (Netherlands)

2016-11-15

An important question in the theory of double parton scattering is how to incorporate the possibility of the parton pairs being generated perturbatively via 1→ 2splitting into the theory, whilst avoiding double counting with single parton scattering loop corrections. Here, we describe a consistent approach for solving this problem, which retains the notion of double parton distributions (DPDs) for individual hadrons. Further, we discuss the construction of appropriate model DPDs in our framework, and the use of these to compute the DPS part, presenting DPS 'luminosities' from our model DPDs for a few sample cases.

Microplastics in Baltic bottom sediments: Quantification procedures and first results.

Science.gov (United States)

Zobkov, M; Esiukova, E

2017-01-30

Microplastics in the marine environment are known as a global ecological problem but there are still no standardized analysis procedures for their quantification. The first breakthrough in this direction was the NOAA Laboratory Methods for quantifying synthetic particles in water and sediments, but fibers numbers have been found to be underestimated with this approach. We propose modifications for these methods that will allow us to analyze microplastics in bottom sediments, including small fibers. Addition of an internal standard to sediment samples and occasional empty runs are advised for analysis quality control. The microplastics extraction efficiency using the proposed modifications is 92±7%. Distribution of microplastics in bottom sediments of the Russian part of the Baltic Sea is presented. Microplastic particles were found in all of the samples with an average concentration of 34±10 items/kg DW and have the same order of magnitude as neighbor studies reported. Copyright © 2016 Elsevier Ltd. All rights reserved.

Bottom-quark forward-backward asymmetry, dark matter, and the LHC

Science.gov (United States)

Liu, Da; Liu, Jia; Wagner, Carlos E. M.; Wang, Xiao-Ping

2018-03-01

The LEP experiment at CERN provided accurate measurements of the Z neutral gauge boson properties. Although all measurements agree well with the standard model (SM) predictions, the forward backward asymmetry of the bottom-quark remains almost 3 σ away from the SM value. We proposed that this anomaly may be explained by the existence of a new U (1 )D gauge boson, which couples with opposite charges to the right-handed components of the bottom and charm quarks. Cancellation of gauge anomalies demands the presence of a vector-like singlet charged lepton as well as a neutral Dirac (or Majorana) particle that provides a dark matter candidate. Constraints from precision measurements imply that the mass of the new gauge boson should be around 115 GeV. We discuss the experimental constraints on this scenario, including the existence of a di-jet resonance excess at an invariant mass similar to the mass of this new gauge boson, observed in boosted topologies at the CMS experiment.

Behavioral and neural evidence of increased attention to the bottom half of the face in deaf signers

Science.gov (United States)

Mitchell, Teresa V.; Letourneau, Susan M.; Maslin, Melissa T.

2013-01-01

Purpose This study examined the effects of deafness and sign language use on the distribution of attention across the top and bottom halves of faces. Methods In a composite face task, congenitally deaf signers and typically hearing controls made same/different judgments of the top or bottom halves of faces presented with the halves aligned or spatially misaligned, while event-related potentials (ERPs) were recorded. Results Both groups were more accurate when judging misaligned than aligned faces, which indicates holistic face processing. Misalignment affected all ERP components examined, with effects on the N170 resembling those of face inversion. Hearing adults were similarly accurate when judging the top and bottom halves of the faces, but deaf signers were more accurate when attending to the bottom than the top. Attending to the top elicited faster P1 and N170 latencies for both groups; within the deaf group, this effect was greatest for individuals who produced the highest accuracies when attending to the top. Conclusions These findings dovetail with previous research by providing behavioral and neural evidence of increased attention to the bottom half of the face in deaf signers, and by documenting that these effects generalize to a speeded task, in the absence of gaze shifts, with neutral facial expressions. PMID:23142816

Top-down versus bottom-up processing of influence diagrams in probabilistic analysis

International Nuclear Information System (INIS)

Timmerman, R.D.; Burns, T.J.; Dodds, H.L. Jr.

1984-01-01

Recent work by Phillips et al., and Selby et al., has shown that influence diagram methodology can be a useful analytical tool in reactor safety studies. An influence diagram is a graphical representation of probabilistic dependence within a system or event sequence. Bayesian statistics are employed to transform the relationships depicted in the influence diagram into the correct expression for a desired marginal probability (e.g. the top event). As with fault trees, top-down and bottom-up algorithms have emerged as the dominant methods for quantifying influence diagrams. Purpose of this paper is to demonstrate a potential error in employing the bottom-up algorithm when dealing with interdependencies. In addition, the computing efficiency of both methods is discussed

A balance of bottom-up and top-down in linking climate policies

Science.gov (United States)

Green, Jessica F.; Sterner, Thomas; Wagner, Gernot

2014-12-01

Top-down climate negotiations embodied by the Kyoto Protocol have all but stalled, chiefly because of disagreements over targets and objections to financial transfers. To avoid those problems, many have shifted their focus to linkage of bottom-up climate policies such as regional carbon markets. This approach is appealing, but we identify four obstacles to successful linkage: different levels of ambition; competing domestic policy objectives; objections to financial transfers; and the difficulty of close regulatory coordination. Even with a more decentralized approach, overcoming the 'global warming gridlock' of the intergovernmental negotiations will require close international coordination. We demonstrate how a balance of bottom-up and top-down elements can create a path toward an effective global climate architecture.

Integrated Assessment of Energy Policies: A Decomposition of Top-Down and Bottom-Up

Energy Technology Data Exchange (ETDEWEB)

Boehringer, Christoph (Univ. of Oldenburg (Germany)); Rutherford, Thomas F. (ETH Zuerich (Switzerland))

2008-01-15

The formulation of market equilibrium problems as mixed complementarity problems (MCP) permits integration of bottom-up programming models of the energy system into top-down general equilibrium models of the overall economy. Yet, in practise the MCP approach loses analytical tractability of income effects, when the energy system includes upper and lowrbounds on many decision variables . We therefore advocate the use of complementarity methods to solve only the top-down economic equilibrium model and employ quadratic programming to solve the underlying bottom-up energy supply model. A simple iterative procedure reconciles the equilibrium prices and quantities between both models.

When endogenous spatial attention improves conscious perception: effects of alerting and bottom-up activation.

Science.gov (United States)

Botta, Fabiano; Lupiáñez, Juan; Chica, Ana B

2014-01-01

Recent studies have consistently demonstrated that conscious perception interacts with exogenous attentional orienting, but it can be dissociated from endogenous attentional orienting (Chica Lasaponara, et al., 2011; Wyart & Tallon-Baudry, 2008). It has been hypothesized that enhanced conscious processing at exogenously attended locations results from a synergistic action of spatial orienting, bottom-up activation, and phasic alerting induced by the abrupt onset of the exogenous cue (Chica, Lasaponara, et al., 2011). Instead, as endogenous cues need more time to be interpreted, the phasic alerting they produce may have dissipated when the target appears. Furthermore, endogenous cues presumably elicit a weak bottom-up activation at the cued location. Consistent with these hypotheses, we observed that endogenous attention modulated conscious perception, but only when phasic alerting or bottom-up activation was increased. Results are discussed in the context of recent theoretical models of consciousness (Dehaene, Changeux, Naccache, Sackur, & Sergent, 2006). Copyright © 2013 Elsevier Inc. All rights reserved.

Measuring Zonal Transport Variability of the Antarctic Circumpolar Current Using GRACE Ocean Bottom Pressure

Science.gov (United States)

Makowski, J.; Chambers, D. P.; Bonin, J. A.

2012-12-01

Previous studies have suggested that ocean bottom pressure (OBP) can be used to measure the transport variability of the Antarctic Circumpolar Current (ACC). Using OBP data from the JPL ECCO model and the Gravity Recovery and Climate Experiment (GRACE), we examine the zonal transport variability of the ACC integrated between the major fronts between 2003-2010. The JPL ECCO data are used to determine average front positions for the time period studies, as well as where transport is mainly zonal. Statistical analysis will be conducted to determine the uncertainty of the GRACE observations using a simulated data set. We will also begin looking at low frequency changes and how coherent transport variability is from region to region of the ACC. Correlations with bottom pressure south of the ACC and the average basin transports will also be calculated to determine the probability of using bottom pressure south of the ACC as a means for describing the ACC dynamics and transport.

Enhanced stability of thin film transistors with double-stacked amorphous IWO/IWO:N channel layer

Science.gov (United States)

Lin, Dong; Pi, Shubin; Yang, Jianwen; Tiwari, Nidhi; Ren, Jinhua; Zhang, Qun; Liu, Po-Tsun; Shieh, Han-Ping

2018-06-01

In this work, bottom-gate top-contact thin film transistors with double-stacked amorphous IWO/IWO:N channel layer were fabricated. Herein, amorphous IWO and N-doped IWO were deposited as front and back channel layers, respectively, by radio-frequency magnetron sputtering. The electrical characteristics of the bi-layer-channel thin film transistors (TFTs) were examined and compared with those of single-layer-channel (i.e., amorphous IWO or IWO:N) TFTs. It was demonstrated to exhibit a high mobility of 27.2 cm2 V‑1 s‑1 and an on/off current ratio of 107. Compared to the single peers, bi-layer a-IWO/IWO:N TFTs showed smaller hysteresis and higher stability under negative bias stress and negative bias temperature stress. The enhanced performance could be attributed to its unique double-stacked channel configuration, which successfully combined the merits of the TFTs with IWO and IWO:N channels. The underlying IWO thin film provided percolation paths for electron transport, meanwhile, the top IWO:N layer reduced the bulk trap densities. In addition, the IWO channel/gate insulator interface had reduced defects, and IWO:N back channel surface was insensitive to the ambient atmosphere. Overall, the proposed bi-layer a-IWO/IWO:N TFTs show potential for practical applications due to its possibly long-term serviceability.

Modelling of landfill gas adsorption with bottom ash for utilization of renewable energy

Energy Technology Data Exchange (ETDEWEB)

Miao, Chen

2011-10-06

Energy crisis, environment pollution and climate change are the serious challenges to people worldwide. In the 21st century, human being is trend to research new technology of renewable energy, so as to slow down global warming and develop society in an environmentally sustainable method. Landfill gas, produced by biodegradable municipal solid waste in landfill, is a renewable energy source. In this work, landfill gas utilization for energy generation is introduced. Landfill gas is able to produce hydrogen by steam reforming reactions. There is a steam reformer equipment in the fuel cells system. A sewage plant of Cologne in Germany has run the Phosphoric Acid Fuel Cells power station with biogas for more than 50,000 hours successfully. Landfill gas thus may be used as fuel for electricity generation via fuel cells system. For the purpose of explaining the possibility of landfill gas utilization via fuel cells, the thermodynamics of landfill gas steam reforming are discussed by simulations. In practice, the methane-riched gas can be obtained by landfill gas purification and upgrading. This work investigate a new method for upgrading-landfill gas adsorption with bottom ash experimentally. Bottom ash is a by-product of municipal solid waste incineration, some of its physical and chemical properties are analysed in this work. The landfill gas adsorption experimental data show bottom ash can be used as a potential adsorbent for landfill gas adsorption to remove CO{sub 2}. In addition, the alkalinity of bottom ash eluate can be reduced in these adsorption processes. Therefore, the interactions between landfill gas and bottom ash can be explained by series reactions accordingly. Furthermore, a conceptual model involving landfill gas adsorption with bottom ash is developed. In this thesis, the parameters of landfill gas adsorption equilibrium equations can be obtained by fitting experimental data. On the other hand, these functions can be deduced with theoretical approach

Station blackout calculations for Peach Bottom

International Nuclear Information System (INIS)

Hodge, S.A.

1985-01-01

A calculational procedure for the Station Blackout Severe Accident Sequence at Browns Ferry Unit One has been repeated with plant-specific application to one of the Peach Bottom Units. The only changes required in code input are with regard to the primary continment concrete, the existence of sprays in the secondary containment, and the size of the refueling bay. Combustible gas mole fractions in the secondary containment of each plant during the accident sequence are determined. It is demonstrated why the current state-of-the-art corium/concrete interaction code is inadequate for application to the study of Severe Accident Sequences in plants with the BWR MK I or MK II containment design

Renormalization group improved bottom mass from {Upsilon} sum rules at NNLL order

Energy Technology Data Exchange (ETDEWEB)

Hoang, Andre H.; Stahlhofen, Maximilian [Wien Univ. (Austria). Fakultaet fuer Physik; Ruiz-Femenia, Pedro [Wien Univ. (Austria). Fakultaet fuer Physik; Valencia Univ. - CSIC (Spain). IFIC

2012-09-15

We determine the bottom quark mass from non-relativistic large-n {Upsilon} sum rules with renormalization group improvement at next-to-next-to-leading logarithmic order. We compute the theoretical moments within the vNRQCD formalism and account for the summation of powers of the Coulomb singularities as well as of logarithmic terms proportional to powers of {alpha}{sub s} ln(n). The renormalization group improvement leads to a substantial stabilization of the theoretical moments compared to previous fixed-order analyses, which did not account for the systematic treatment of the logarithmic {alpha}{sub s} ln(n) terms, and allows for reliable single moment fits. For the current world average of the strong coupling ({alpha}{sub s}(M{sub Z})=0.1183{+-}0.0010) we obtain M{sub b}{sup 1S}=4.755{+-}0.057{sub pert} {+-}0.009{sub {alpha}{sub s}}{+-}0.003{sub exp} GeV for the bottom 1S mass and anti m{sub b}(anti m{sub b})=4.235{+-}0.055{sub pert}{+-}0.003{sub exp} GeV for the bottom MS mass, where we have quoted the perturbative error and the uncertainties from the strong coupling and the experimental data.

Mixing Phenomena in a Bottom Blown Copper Smelter: A Water Model Study

Science.gov (United States)

Shui, Lang; Cui, Zhixiang; Ma, Xiaodong; Akbar Rhamdhani, M.; Nguyen, Anh; Zhao, Baojun

2015-03-01

The first commercial bottom blown oxygen copper smelting furnace has been installed and operated at Dongying Fangyuan Nonferrous Metals since 2008. Significant advantages have been demonstrated in this technology mainly due to its bottom blown oxygen-enriched gas. In this study, a scaled-down 1:12 model was set up to simulate the flow behavior for understanding the mixing phenomena in the furnace. A single lance was used in the present study for gas blowing to establish a reliable research technique and quantitative characterisation of the mixing behavior. Operating parameters such as horizontal distance from the blowing lance, detector depth, bath height, and gas flow rate were adjusted to investigate the mixing time under different conditions. It was found that when the horizontal distance between the lance and detector is within an effective stirring range, the mixing time decreases slightly with increasing the horizontal distance. Outside this range, the mixing time was found to increase with increasing the horizontal distance and it is more significant on the surface. The mixing time always decreases with increasing gas flow rate and bath height. An empirical relationship of mixing time as functions of gas flow rate and bath height has been established first time for the horizontal bottom blowing furnace.

Document de travail 5: Beyond Collier's Bottom Billion | CRDI ...

International Development Research Centre (IDRC) Digital Library (Canada)

16 déc. 2010 ... L'ouvrage de Paul Collier, The Bottom Billion, suscite un grand intérêt dans le domaine du développement. Il repose sur la thèse selon laquelle un groupe de près de 60 pays, dont la population totale avoisine un milliard de personnes, sont pris dans quatre pièges principaux.

Bottom Sediment Chemistry, Nutrient Balance, and Water Birds in ...

African Journals Online (AJOL)

Water bird characteristics, nutrient loadings, and the levels of bottom sediment silicon oxide (SiO2), aluminium oxide (Al2O3), ferric oxide (Fe2O3), calcium oxide (CaO), copper (Cu), phosphorus (P) and organic carbon (C) was studied in eight high altitude (2040-2640m) small shallow (0.065-0.249 km2; 0.9-3.1 m) ...

Emotional face expression modulates occipital-frontal effective connectivity during memory formation in a bottom-up fashion

Directory of Open Access Journals (Sweden)

Daiming eXiu

2015-04-01

Full Text Available This study investigated the role of bottom-up and top-down neural mechanisms in the processing of emotional face expression during memory formation. Functional brain imaging data was acquired during incidental learning of positive (‘happy’, neutral and negative (‘angry’ or ‘fearful’ faces. Dynamic Causal Modeling (DCM was applied on the fMRI data to characterize effective connectivity within a brain network involving face perception (inferior occipital gyrus and fusiform gyrus and successful memory formation related areas (hippocampus, superior parietal lobule, amygdala and orbitofrontal cortex. The bottom-up models assumed processing of emotional face expression along feed forward pathways to the orbitofrontal cortex. The top-down models assumed that the orbitofrontal cortex processed emotional valence and mediated connections to the hippocampus. A subsequent recognition memory test showed an effect of negative emotion on the response bias, but not on memory performance. Our DCM findings showed that the bottom-up model family of effective connectivity best explained the data across all subjects and specified that emotion affected most bottom-up connections to the orbitofrontal cortex, especially from the occipital visual cortex and superior parietal lobule. Of those pathways to the orbitofrontal cortex the connection from the inferior occipital gyrus correlated with memory performance independently of valence. We suggest that bottom-up neural mechanisms support effects of emotional face expression and memory formation in a parallel and partially overlapping fashion.

Compressive strength performance of OPS lightweight aggregate concrete containing coal bottom ash as partial fine aggregate replacement

Science.gov (United States)

Muthusamy, K.; Mohamad Hafizuddin, R.; Mat Yahaya, F.; Sulaiman, M. A.; Syed Mohsin, S. M.; Tukimat, N. N.; Omar, R.; Chin, S. C.

2018-04-01

Concerns regarding the negative impact towards environment due to the increasing use of natural sand in construction industry and dumping of industrial solid wastes namely coal bottom ash (CBA) and oil palm shell (OPS) has resulted in the development of environmental friendly lightweight concrete. The present study investigates the effect of coal bottom ash as partial fine aggregate replacement towards workability and compressive strength of oil palm shell lightweight aggregate concrete (OPS LWAC). The fresh and mechanical properties of this concrete containing various percentage of coal bottom ash as partial fine aggregate replacement were investigated. The result was compared to OPS LWAC with 100 % sand as a control specimen. The concrete workability investigated by conducting slump test. All specimens were cast in form of cubes and water cured until the testing age. The compressive strength test was carried out at 7 and 28 days. The finding shows that integration of coal bottom ash at suitable proportion enhances the strength of oil palm shell lightweight aggregate concrete.

Magnetic and transport properties of single and double perpendicular magnetic tunnel junctions

International Nuclear Information System (INIS)

Cuchet, Lea

2015-01-01

Due to their advantageous properties in terms of data retention, storage density and critical current density for Spin Transfer Torque (STT) switching, the magnetic tunnel junctions with perpendicular anisotropy have become predominant in the developments for MRAM applications. The aim of this thesis is to improve the anisotropy and transport properties of such structures and to realize even more complex stacks such as perpendicular double junctions. Studies on the magnetic properties and Tunnel Magnetoresistance (TMR) measurements showed that to optimize the performances of the junctions, all the thicknesses of the different layers constituting the stack have to be adapted. To guaranty both a large TMR as well a strong perpendicular anisotropy, compromises are most of the time needed. Studies as a function of magnetic thickness enabled to extract the saturation magnetization, the critical thickness and the magnetic dead layer thickness both in the bottom reference and the top storage layer in structures capped with Ta. This type of junction could be tested electrically after patterning the sample into nano-pillars. Knowing that perpendicular anisotropy mostly arises at the metal/oxide interface, the Ta capping layer was replaced by a MgO one, leading to a huge increase in the anisotropy of the free layer. A second top reference was then added on such a stack to create functional perpendicular double junctions. CoFeB/insertion/CoFeB synthetic antiferromagnetic storage layers could be developed and were proved to be stable enough to replace the standard Co/Pt-based reference layers. (author) [fr

Decades with four double triodes; Decades a quatre doubles triodes

Energy Technology Data Exchange (ETDEWEB)

Wahl, R [Commissariat a l' Energie Atomique, Lab. du Fort de Chatillon, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

1952-07-01

Decades with four double triodes The described decade consists of four double triodes and four crystals germanium; which has the following characteristics: - Attack in negative impulses. - Sensitivity 12 volts {+-} 40 % for signals of 1 {mu}s about. - Time of resolution 2,5 {mu}s. - Voltage 250 v {+-} 40 %. - heating 6,3 v {+-} 40 %. - Tolerance on the values of the elements of installation 10%. (author) [French] La decade decrite comprend quatre doubles triodes et quatre cristaux germanium; elle a les caracteristiques suivantes: - Attaque en impulsions negatives. - Sensiblite 12 volts {+-} 40 % pour des signaux de 1 {mu}s environ. - Temps de resolution 2,5 {mu}s. - Alimentation 250 v {+-} 40 %. - Chauffage 6,3 v {+-} 40 %. - Tolerance sur les valeurs des elements de montage l0 %. (auteur)

Antimony leaching from MSWI bottom ash: modelling of the effect of pH and carbonation.

Science.gov (United States)

Cornelis, Geert; Van Gerven, Tom; Vandecasteele, Carlo

2012-02-01

Development of treatment methods to reduce Sb leaching from municipal solid waste incinerator (MSWI) bottom ash, such as accelerated carbonation, is being complicated by insufficient understanding of Sb geochemistry. The leaching of antimonate (Sb(V)) and antimonite (Sb(III)) in MSWI bottom was studied as a function of pH and degree of carbonation. While total (Sb(V)+Sb(III)) leaching was lowest (1.2 mg kg(-1)) at the natural pH (i.e. 10.6) of uncarbonated bottom ash, HPLC-ICP-MS analysis showed that acidification and carbonation increased Sb(V) leaching, but decreased Sb(III) leaching, probably because Sb(III)(OH)(4)(-) became less stable. PHREEQC geochemical modelling suggested that Sb(V) concentrations approached equilibrium with the romeites, i.e. calcium antimonates, Ca(1.13)Sb(2)(OH)(0.26)·0.74H(2)O at pH=10.6 and Ca[Sb(OH)(6)](2) at pH=8. It is hypothesised that not interaction with ettringite but dissolution of romeite controls antimonate leaching in the pH range 8-11 in MSWI bottom ash, because while Ca is preferentially leached from romeite, the mineral structures containing more Ca at higher pH are less soluble. A model was proposed where acidification and carbonation both lead to lower Ca(2+) and/or hydroxyl concentration, which removes Ca(2+) and hydroxyls from the romeite structure and leads to comparably higher Sb(V) concentration in equilibrium with romeite. Sb solubility depends on pH and Ca(2+) availability in this model, which has implications for bottom ash valorisation and risk assessment. Copyright © 2011 Elsevier Ltd. All rights reserved.

Stress testing hydrologic models using bottom-up climate change assessment

Science.gov (United States)

Stephens, C.; Johnson, F.; Marshall, L. A.

2017-12-01

Bottom-up climate change assessment is a promising approach for understanding the vulnerability of a system to potential future changes. The technique has been utilised successfully in risk-based assessments of future flood severity and infrastructure vulnerability. We find that it is also an ideal tool for assessing hydrologic model performance in a changing climate. In this study, we applied bottom-up climate change to compare the performance of two different hydrologic models (an event-based and a continuous model) under increasingly severe climate change scenarios. This allowed us to diagnose likely sources of future prediction error in the two models. The climate change scenarios were based on projections for southern Australia, which indicate drier average conditions with increased extreme rainfall intensities. We found that the key weakness in using the event-based model to simulate drier future scenarios was the model's inability to dynamically account for changing antecedent conditions. This led to increased variability in model performance relative to the continuous model, which automatically accounts for the wetness of a catchment through dynamic simulation of water storages. When considering more intense future rainfall events, representation of antecedent conditions became less important than assumptions around (non)linearity in catchment response. The linear continuous model we applied may underestimate flood risk in a future climate with greater extreme rainfall intensity. In contrast with the recommendations of previous studies, this indicates that continuous simulation is not necessarily the key to robust flood modelling under climate change. By applying bottom-up climate change assessment, we were able to understand systematic changes in relative model performance under changing conditions and deduce likely sources of prediction error in the two models.

Small break loss of coolant accidents: Bottom and side break

International Nuclear Information System (INIS)

Hardy, P.G.; Richter, H.J.

1987-01-01

A LOCA can be caused, e.g. by a small break in the primary cooling system. The rate of fluid escaping through such a break will define the time until the core will be uncovered. Therefore the prediction of fluid loss and pressure transient is of major importance to plan for timely action in response to such an event. Stratification of the two phases might be present upstream of the break, thus, the location of the break relative to the vapor-liquid interface and the overall upstream fluid conditions are relevant for the calculation of fluid loss. Experimental results and analyses are presented here for small breaks at the bottom or at the side of a small pressure vessel. It was found that in such a case the onset of the so-called ''vapor pull through'' is important but swelling at sufficient depressurization rates of the liquid due to flashing is also of significance. It was also discovered that in the bottom break the flow rate is strongly dependent on the break entrance quality of the vapour-liquid mixture. The side break can be treated similarly to the bottom break if the interface level is above the break. The analyses developed on the basis of experimental observations showed reasonable agreement of predicted and measured pressure transients. It was possible to calculate the changing interface level and mixture void fraction history in a way compatible with the behavior observed during the experiments. Even though the experiments were performed at low pressures, this work should help to get a better understanding of physical phenomena occurring in a full scale small break LOCA. (orig./HP)

Assessing the Gap Between Top-down and Bottom-up Measured Methane Emissions in Indianapolis, IN.

Science.gov (United States)

Prasad, K.; Lamb, B. K.; Cambaliza, M. O. L.; Shepson, P. B.; Stirm, B. H.; Salmon, O. E.; Lavoie, T. N.; Lauvaux, T.; Ferrara, T.; Howard, T.; Edburg, S. L.; Whetstone, J. R.

2014-12-01

Releases of methane (CH4) from the natural gas supply chain in the United States account for approximately 30% of the total US CH4 emissions. However, there continues to be large questions regarding the accuracy of current emission inventories for methane emissions from natural gas usage. In this paper, we describe results from top-down and bottom-up measurements of methane emissions from the large isolated city of Indianapolis. The top-down results are based on aircraft mass balance and tower based inverse modeling methods, while the bottom-up results are based on direct component sampling at metering and regulating stations, surface enclosure measurements of surveyed pipeline leaks, and tracer/modeling methods for other urban sources. Mobile mapping of methane urban concentrations was also used to identify significant sources and to show an urban-wide low level enhancement of methane levels. The residual difference between top-down and bottom-up measured emissions is large and cannot be fully explained in terms of the uncertainties in top-down and bottom-up emission measurements and estimates. Thus, the residual appears to be, at least partly, attributed to a significant wide-spread diffusive source. Analyses are included to estimate the size and nature of this diffusive source.

Transport of mass goods on the top run and bottom run of belt conveyors

Energy Technology Data Exchange (ETDEWEB)

Zimmermann, D

1977-06-01

For combined coal winning from the collieries 'General Blumenthal' and 'Ewald Fortsetzung' a large belt conveyor plant was taken into operation which is able to transport 1360 tons/h in the top run and 300 tons/h of dirt in the bottom run. The different types of coal are transported separately in intermittent operation with the aid of bunker systems connected to the front and rear of the belt conveyor. Persons can be transported in the top run as well as in the bottom run.

Searches for scalar top and scalar bottom quarks at LEP2

Science.gov (United States)

ALEPH Collaboration; Barate, R.; Buskulic, D.; Decamp, D.; Ghez, P.; Goy, C.; Lees, J.-P.; Lucotte, A.; Minard, M.-N.; Nief, J.-Y.; Pietrzyk, B.; Casado, M. P.; Chmeissani, M.; Comas, P.; Crespo, J. M.; Delfino, M.; Fernandez, E.; Fernandez-Bosman, M.; Garrido, Ll.; Juste, A.; Martinez, M.; Merino, G.; Miquel, R.; Mir, Ll. M.; Padilla, C.; Park, I. C.; Pascual, A.; Perlas, J. A.; Riu, I.; Sanchez, F.; Teubert, F.; Colaleo, A.; Creanza, D.; de Palma, M.; Gelao, G.; Iaselli, G.; Maggi, G.; Maggi, M.; Marinelli, N.; Nuzzo, S.; Ranieri, A.; Raso, G.; Ruggieri, F.; Selvaggi, G.; Silvestris, L.; Tempesta, P.; Tricomi, A.; Zito, G.; Huang, X.; Lin, J.; Ouyang, Q.; Wang, T.; Xie, Y.; Xu, R.; Xue, S.; Zhang, J.; Zhang, L.; Zhao, W.; Abbaneo, D.; Alemany, R.; Bazarko, A. O.; Becker, U.; Bright-Thomas, P.; Cattaneo, M.; Cerutti, F.; Dissertori, G.; Drevermann, H.; Forty, R. W.; Frank, M.; Hagelberg, R.; Hansen, J. B.; Harvey, J.; Janot, P.; Jost, B.; Kneringer, E.; Knobloch, J.; Lehraus, I.; Mato, P.; Minten, A.; Moneta, L.; Pacheco, A.; Pusztaszeri, J.-F.; Ranjard, F.; Rizzo, G.; Rolandi, L.; Rousseau, D.; Schlatter, D.; Schmitt, M.; Schneider, O.; Tejessy, W.; Tomalin, I. R.; Wachsmuth, H.; Wagner, A.; Ajaltouni, Z.; Barrès, A.; Boyer, C.; Falvard, A.; Ferdi, C.; Gay, P.; Guicheney, C.; Henrard, P.; Jousset, J.; Michel, B.; Monteil, S.; Montret, J.-C.; Pallin, D.; Perret, P.; Podlyski, F.; Proriol, J.; Rosnet, P.; Rossignol, J.-M.; Fearnley, T.; Hansen, J. D.; Hansen, J. R.; Hansen, P. H.; Nilsson, B. S.; Rensch, B.; Wäänänen, A.; Daskalakis, G.; Kyriakis, A.; Markou, C.; Simopoulou, E.; Vayaki, A.; Blondel, A.; Brient, J. C.; Machefert, F.; Rougé, A.; Rumpf, M.; Valassi, A.; Videau, H.; Focardi, E.; Parrini, G.; Zachariadou, K.; Cavanaugh, R.; Corden, M.; Georgiopoulos, C.; Huehn, T.; Jaffe, D. E.; Antonelli, A.; Bencivenni, G.; Bologna, G.; Bossi, F.; Campana, P.; Capon, G.; Casper, D.; Chiarella, V.; Felici, G.; Laurelli, P.; Mannocchi, G.; Murtas, F.; Murtas, G. P.; Passalacqua, L.; Pepe-Altarelli, M.; Curtis, L.; Dorris, S. J.; Halley, A. W.; Knowles, I. G.; Lynch, J. G.; O'Shea, V.; Raine, C.; Scarr, J. M.; Smith, K.; Teixeira-Dias, P.; Thompson, A. S.; Thomson, E.; Thomson, F.; Turnbull, R. M.; Buchmüller, O.; Dhamotharan, S.; Geweniger, C.; Graefe, G.; Hanke, P.; Hansper, G.; Hepp, V.; Kluge, E. E.; Putzer, A.; Sommer, J.; Tittel, K.; Werner, S.; Wunsch, M.; Beuselinck, R.; Binnie, D. M.; Cameron, W.; Dornan, P. J.; Girone, M.; Goodsir, S.; Martin, E. B.; Morawitz, P.; Moutoussi, A.; Nash, J.; Sedgbeer, J. K.; Spagnolo, P.; Stacey, A. M.; Williams, M. D.; Ghete, V. M.; Girtler, P.; Kuhn, D.; Rudolph, G.; Betteridge, A. P.; Bowdery, C. K.; Colrain, P.; Crawford, G.; Finch, A. J.; Foster, F.; Hughes, G.; Jones, R. W. L.; Sloan, T.; Whelan, E. P.; Williams, M. I.; Hoffmann, C.; Jakobs, K.; Kleinknecht, K.; Quast, G.; Renk, B.; Rohne, E.; Sander, H.-G.; van Gemmeren, P.; Zeitnitz, C.; Aubert, J. J.; Benchouk, C.; Bonissent, A.; Bujosa, G.; Carr, J.; Coyle, P.; Diaconu, C.; Ealet, A.; Fouchez, D.; Konstantinidis, N.; Leroy, O.; Motsch, F.; Payre, P.; Talby, M.; Sadouki, A.; Thulasidas, M.; Tilquin, A.; Trabelsi, K.; Aleppo, M.; Antonelli, M.; Ragusa, F.; Berlich, R.; Blum, W.; Büscher, V.; Dietl, H.; Ganis, G.; Gotzhein, C.; Kroha, H.; Lütjens, G.; Lutz, G.; Männer, W.; Moser, H.-G.; Richter, R.; Rosado-Schlosser, A.; Schael, S.; Settles, R.; Seywerd, H.; St. Denis, R.; Stenzel, H.; Wiedenmann, W.; Wolf, G.; Boucrot, J.; Callot, O.; Chen, S.; Cordier, A.; Davier, M.; Duflot, L.; Grivaz, J.-F.; Heusse, Ph.; Höcker, A.; Jacholkowska, A.; Jacquet, M.; Kim, D. W.; Le Diberder, F.; Lefrançois, J.; Lutz, A.-M.; Nikolic, I.; Schune, M.-H.; Serin, L.; Simion, S.; Tournefier, E.; Veillet, J.-J.; Videau, I.; Zerwas, D.; Azzurri, P.; Bagliesi, G.; Bettarini, S.; Bozzi, C.; Calderini, G.; Ciulli, V.; dell'Orso, R.; Fantechi, R.; Ferrante, I.; Giassi, A.; Gregorio, A.; Ligabue, F.; Lusiani, A.; Marrocchesi, P. S.; Messineo, A.; Palla, F.; Sanguinetti, G.; Sciabà, A.; Sguazzoni, G.; Steinberger, J.; Tenchini, R.; Vannini, C.; Venturi, A.; Verdini, P. G.; Blair, G. A.; Bryant, L. M.; Chambers, J. T.; Gao, Y.; Green, M. G.; Medcalf, T.; Perrodo, P.; Strong, J. A.; von Wimmersperg-Toeller, J. H.; Botterill, D. R.; Clifft, R. W.; Edgecock, T. R.; Haywood, S.; Maley, P.; Norton, P. R.; Thompson, J. C.; Wright, A. E.; Bloch-Devaux, B.; Colas, P.; Fabbro, B.; Kozanecki, W.; Lançon, E.; Lemaire, M. C.; Locci, E.; Perez, P.; Rander, J.; Renardy, J.-F.; Rosowsky, A.; Roussarie, A.; Schuller, J.-P.; Schwindling, J.; Trabelsi, A.; Vallage, B.; Black, S. N.; Dann, J. H.; Kim, H. Y.; Litke, A. M.; McNeil, M. A.; Taylor, G.; Booth, C. N.; Boswell, R.; Brew, C. A. J.; Cartwright, S.; Combley, F.; Kelly, M. S.; Lehto, M.; Newton, W. M.; Reeve, J.; Thompson, L. F.; Affholderbach, K.; Böhrer, A.; Brandt, S.; Cowan, G.; Foss, J.; Grupen, C.; Lutters, G.; Saraiva, P.; Smolik, L.; Stephan, F.; Apollonio, M.; Bosisio, L.; della Marina, R.; Giannini, G.; Gobbo, B.; Musolino, G.; Putz, J.; Rothberg, J.; Wasserbaech, S.; Williams, R. W.; Armstrong, S. R.; Charles, E.; Elmer, P.; Ferguson, D. P. S.; González, S.; Greening, T. C.; Hayes, O. J.; Hu, H.; Jin, S.; McNamara, P. A., III; Nachtman, J. M.; Nielsen, J.; Orejudos, W.; Pan, Y. B.; Saadi, Y.; Scott, I. J.; Walsh, J.; Wu, Sau Lan; Wu, X.; Yamartino, J. M.; Zobernig, G.

1997-11-01

Searches for scalar top and bottom quarks have been performed with data collected by the ALEPH detector at LEP. The data sample consists of 21.7 pb-1 taken at sqrt(s) = 161, 170, and 172 GeV and 5.7 pb-1 taken at sqrt(s) = 130 and 136 GeV. No evidence for scalar top quarks or scalar bottom quarks was found in the channels t~-->cχ, t~-->blν~, and b~-->bχ. For the channel t~-->cχ a limit of 67 GeV/c2has been set on the scalar top quark mass, independent of the mixing angle between the supersymmetric partners of the left and right-handed states of the top quark. This limit assumes a mass difference between the t~ and the χ of at least 10 GeV/c2. For the channel t~-->blν~ the mixing-angle independent scalar top limit is 70 GeV/c2, assuming a mass difference between the t~ and the ν~ of at least 10 GeV/c2. For the channel b~-->bχ, a limit of 73 GeV/c2has been set on the mass of the supersymmetric partner of the left-handed state of the bottom quark. This limit is valid if the mass difference between the b~ and the χ is at least 10 GeV/c2.

Infaunal macrobenthic community of soft bottom sediment in a tropical shelf

Digital Repository Service at National Institute of Oceanography (India)

Jayaraj, K.A.; Jacob, J.; DineshKumar, P.K.

Studies of benthic communities in tropical shelf waters are limited. In this study, we deal with the infaunal benthic community of soft bottom sediment of the tropical eastern Arabian Sea shelf. Benthic macroinfauna was sampled with a Smith...

Top, Bottom, and Versatile Anal Sex Roles in Same-Sex Male Relationships: Implications for Relationship and Sexual Satisfaction.

Science.gov (United States)

Moskowitz, David A; Garcia, Christopher P

2018-06-01

Across much of the gay and bisexual male research on sexual position self-label (i.e., calling oneself a top, bottom, or versatile), there exist two commonalities: (1) studies tend to focus almost entirely on individual, relationally single androphilic men; (2) studies rarely account for relationships and relationship dynamics. In response, we explored the role of self-label over sexual and relationship satisfaction among gay and bisexual partnered men. Specifically, we looked at whether adopted sexual position identities were consonant or dissonant (i.e., matching or mismatching) with enacted behavior in relationships and how that impacted men's attitudes toward different relational attributes. Through an online survey, we sampled 169 men in same-sex relationships, asking them questions about their ideal penetrative role identities and their reality penetrative roles with their partner. We then asked them to rate their relationship on 10 sexual and interpersonal attributes. Multiple regression modeling suggested ideal-reality penetrative role dissonance was predictive of sexual dissatisfaction among tops who bottomed in their relationships and, to a lesser extent, bottoms who topped. In contrast, penetrative role dissonance was predictive of relationship satisfaction among tops who bottomed in their relationship, but not bottoms who topped. We conclude that a potential reason for this paradox among tops who bottom may be sexual altruism. That is, men may be satisfied with other aspects within their relationships, understand their partner's anal sex preferences, and accommodate that position in response to their initial relationship satisfaction.

The agronomic landspreading of coal bottom ash: using a regulated solid waste as a resource

Energy Technology Data Exchange (ETDEWEB)

Sell, N; McIntosh, T; Severance, C; Peterson, A

1989-02-01

Within the US, approximately 8860 Mg of dry coal bottom ash is generated daily, the majority of which is disposed of by landfilling. The disposal cost varies significantly depending on location. In Wisconsin, for example, in 1987 public landfill disposal costs ranged from 8.90 US dollars to 30 US dollars per Mg. However, bottom ash appears to be an acceptable soil amendment which may alter texture and improve tilth by making clay soils more friable and decreasing crust formation. If a generic exemption for this material can be developed with the appropriate regulatory bodies, use of coal bottom ash as a soil amendment has societal and economic advantages. This paper describes the key point of an agronomic management plant. An economic comparison indicates that, based on 1987 costs, agronomic use is only 38% as costly as landfill disposal. 14 refs., 5 tabs.

Conceptual Design of Bottom-mounted Control Rod Drive Mechanism

International Nuclear Information System (INIS)

Lee, Jin Haeng; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Dongmin; Kim, Jong In

2013-01-01

The arrangement of the BMCRDMs and irradiation holes in the core is therefore easier than that of the top-mounted CRDM. Hence, many foreign research reactors, such as JRR-3M, JMTR, OPAL, and CARR, have adopted the BMCRDM concept. The purpose of this paper is to introduce the basic design concept on the BMCRDM. The major differences of the CRDMs between HANARO and KJRR are compared, and the design features and individual system of the BMCRDM for the KJRR are described. The Control Rod Drive Mechanism (CRDM) is a device to regulate the reactor power by changing the position of a Control Absorber Rod (CAR) and to shut down the reactor by fully inserting the CAR into the core within a specified time. The Bottom-Mounted CRDM (BMCRDM) for the KiJang Research Reactor (KJRR) is a quite different design concept compared to the top-mounted CRDM such as HANARO and JRTR. The main drive mechanism of the BMCRDM is located in a Reactivity Control Mechanism (RCM) room under the reactor pool bottom, which makes the interference with equipment in the reactor pool reduced

Conceptual Design of Bottom-mounted Control Rod Drive Mechanism

Energy Technology Data Exchange (ETDEWEB)

Lee, Jin Haeng; Kim, Sanghaun; Yoo, Yeonsik; Cho, Yeonggarp; Kim, Dongmin; Kim, Jong In [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

2013-05-15

The arrangement of the BMCRDMs and irradiation holes in the core is therefore easier than that of the top-mounted CRDM. Hence, many foreign research reactors, such as JRR-3M, JMTR, OPAL, and CARR, have adopted the BMCRDM concept. The purpose of this paper is to introduce the basic design concept on the BMCRDM. The major differences of the CRDMs between HANARO and KJRR are compared, and the design features and individual system of the BMCRDM for the KJRR are described. The Control Rod Drive Mechanism (CRDM) is a device to regulate the reactor power by changing the position of a Control Absorber Rod (CAR) and to shut down the reactor by fully inserting the CAR into the core within a specified time. The Bottom-Mounted CRDM (BMCRDM) for the KiJang Research Reactor (KJRR) is a quite different design concept compared to the top-mounted CRDM such as HANARO and JRTR. The main drive mechanism of the BMCRDM is located in a Reactivity Control Mechanism (RCM) room under the reactor pool bottom, which makes the interference with equipment in the reactor pool reduced.

Feature-based attention: it is all bottom-up priming.

Science.gov (United States)

Theeuwes, Jan

2013-10-19

Feature-based attention (FBA) enhances the representation of image characteristics throughout the visual field, a mechanism that is particularly useful when searching for a specific stimulus feature. Even though most theories of visual search implicitly or explicitly assume that FBA is under top-down control, we argue that the role of top-down processing in FBA may be limited. Our review of the literature indicates that all behavioural and neuro-imaging studies investigating FBA suffer from the shortcoming that they cannot rule out an effect of priming. The mere attending to a feature enhances the mandatory processing of that feature across the visual field, an effect that is likely to occur in an automatic, bottom-up way. Studies that have investigated the feasibility of FBA by means of cueing paradigms suggest that the role of top-down processing in FBA is limited (e.g. prepare for red). Instead, the actual processing of the stimulus is needed to cause the mandatory tuning of responses throughout the visual field. We conclude that it is likely that all FBA effects reported previously are the result of bottom-up priming.