Use of the lognormal distribution for the coefficients of friction and wear

International Nuclear Information System (INIS)

Steele, Clint

2008-01-01

To predict the reliability of a system, an engineer might allocate a distribution to each input. This raises a question: how to select the correct distribution? Siddall put forward an evolutionary approach that was intended to utilise both the understanding of the engineer and available data. However, this method requires a subjective initial distribution based on the engineer's understanding of the variable or parameter. If the engineer's understanding is limited, the initial distribution will be misrepresentative of the actual distribution, and application of the method will likely fail. To provide some assistance, the coefficients of friction and wear are considered here. Basic tribology theory, dimensional issues and the central limit theorem are used to argue that the distribution for each of the coefficients will typically be like a lognormal distribution. Empirical evidence from other sources is cited to lend support to this argument. It is concluded that the distributions for the coefficients of friction and wear would typically be lognormal in nature. It is therefore recommended that the engineer, without data or evidence to suggest differently, should allocate a lognormal distribution to the coefficients of friction and wear

Confidence bounds and hypothesis tests for normal distribution coefficients of variation

Science.gov (United States)

Steve Verrill; Richard A. Johnson

2007-01-01

For normally distributed populations, we obtain confidence bounds on a ratio of two coefficients of variation, provide a test for the equality of k coefficients of variation, and provide confidence bounds on a coefficient of variation shared by k populations.

Measurement of distribution coefficients of U series radionuclides on soils under shallow land environment (2). pH dependence of distribution coefficients

International Nuclear Information System (INIS)

Sakamoto, Yoshiaki; Takebe, Shinichi; Ogawa, Hiromichi; Inagawa, Satoshi; Sasaki, Tomozou

2001-01-01

In order to study sorption behavior of U series radionuclides (Pb, Ra, Th, Ac, Pa and U) under aerated zone environment (loam-rain water system) and aquifer environment (sand-groundwater system) for safety assessment of U bearing waste, pH dependence of distribution coefficients of each element has been obtained. The pH dependence of distribution coefficients of Pb, Ra, Th, Ac and U was analyzed by model calculation based on aqueous speciation of each element and soil surface charge characteristics, which is composed of a cation exchange capacity and surface hydroxyl groups. From the model calculation, the sorption behavior of Pb, Ra, Th, Ac and U could be described by a combination of cation exchange reaction and surface-complexation model. (author)

Estimation of the dose delivered to critical organs outside the radiation beams of a Mevatron MX6700 and a Mevatron KDS

International Nuclear Information System (INIS)

Chakkor, H.; Ginjaume, M.; Sanchez-Reyes, A.; Ortega, X.

1994-01-01

The radiation dose received outside collimated radiation is named peripheral dose. The peripheral radiation dose is especially important from a clinical point of view, when some critical organs as eye-lens or gonads are near the target volume,thus generating potential cataract formation, or gonadal disfunction. Accurate prediction of the peripheral dose distribution can also be used in retrospective studies to evaluate possible correlation between radiotherapy dose and secondary cancer incidence in tissues external to the treatment field. The main objective of the present work was the measurement of peripheral dose produced in Siemens Mevatron MX6700 (6 MV) and a Siemens Mevatron KDS (6 and 18 MV linear accelerators. Measurement techniques include the use of a ionization chamber and thermoluminescent dosimeters (TLD) in simple polystyrene phantoms and anthropomorphic phantoms. To obtain high accuracy in the measurements 3 dosemeters were placed in every analyzed point and 10 TLD were situated at the reference point. In addition, an individual calibration factor was used in the dose determination. Doses received in eye-lens, hypophysis, thyroid breast, uterus and gonads, during typical neoplasia treatments as breast neoplasia, head and neck tumour, lung or pelvis tumour and lymphomas are reported. 1 tab.; 1 ref. (author)

Distribution coefficients of purine alkaloids in water-ammonium sulfate-alkyl acetate-dialkyl phthalate systems

Science.gov (United States)

Korenman, Ya. I.; Krivosheeva, O. A.; Mokshina, N. Ya.

2012-12-01

The distribution of purine alkaloids (caffeine, theobromine, theophylline) was studied in the systems: alkyl acetates-dialkyl phtalate-salting-out agent (ammonium sulfate). The quantitative characteristics of the extraction-distribution coefficients ( D) and the degree of extraction ( R, %) are calculated. The relationships between the distribution coefficients of alkaloids and the length of the hydrocarbon radical in the molecule of alkyl acetate (dialkyl phtalate) are determined. The possibility of predicting the distribution coefficients is demonstrated.

Energy distribution for Coefficients of Redundant Signal Representations of Music

DEFF Research Database (Denmark)

Endelt, Line Ørtoft; la Cour-Harbo, Anders

2005-01-01

different time-frequency dictionaries. We have applied these methods to music to examine their ability to express music signals in a sparse manner for a number of dictionaries and window lengths. The evaluation is based on the m-term approximation needed to represent 90 %, 95 %, 99 % and 99......In this paper we investigate how the energy is distributed in the coefficients vector of various redundant signal representations of music signals. The representations are found using Basis Pursuit, Matching Pursuit, Alternating Projections, Best Orthogonal Basis and Method of Frames, with five.......9 % of the energy in the coefficients, also the time consummation for finding the representations are considered. The distribution of energy in the coefficients of the representations found using Basis Pursuit, Matching Pursuit, Alternating Projections and Best Orthogonal Basis depends mainly on the signal...

Confidence bounds for normal and lognormal distribution coefficients of variation

Science.gov (United States)

Steve Verrill

2003-01-01

This paper compares the so-called exact approach for obtaining confidence intervals on normal distribution coefficients of variation to approximate methods. Approximate approaches were found to perform less well than the exact approach for large coefficients of variation and small sample sizes. Web-based computer programs are described for calculating confidence...

Confidence bounds and hypothesis tests for normal distribution coefficients of variation

Science.gov (United States)

Steve P. Verrill; Richard A. Johnson

2007-01-01

For normally distributed populations, we obtain confidence bounds on a ratio of two coefficients of variation, provide a test for the equality of k coefficients of variation, and provide confidence bounds on a coefficient of variation shared by k populations. To develop these confidence bounds and test, we first establish that estimators based on Newton steps from n-...

Distribution coefficient of plutonium between sediment and seawater

International Nuclear Information System (INIS)

Duursma, E.K.; Parsi, P.

1974-01-01

Using plutonium 237 as a tracer, a series of experiments were conducted to determine the distribution coefficient of plutonium onto sediments both under oxic and anoxic conditions, where the plutonium was added to seawater in three different valence states: III, IV and VI

Self-similar optical pulses in competing cubic-quintic nonlinear media with distributed coefficients

International Nuclear Information System (INIS)

Zhang Jiefang; Tian Qing; Wang Yueyue; Dai Chaoqing; Wu Lei

2010-01-01

We present a systematic analysis of the self-similar propagation of optical pulses within the framework of the generalized cubic-quintic nonlinear Schroedinger equation with distributed coefficients. By appropriately choosing the relations between the distributed coefficients, we not only retrieve the exact self-similar solitonic solutions, but also find both the approximate self-similar Gaussian-Hermite solutions and compact solutions. Our analytical and numerical considerations reveal that proper choices of the distributed coefficients could make the unstable solitons stable and could restrict the nonlinear interaction between the neighboring solitons.

On the size distribution of cities: an economic interpretation of the Pareto coefficient.

Science.gov (United States)

Suh, S H

1987-01-01

"Both the hierarchy and the stochastic models of size distribution of cities are analyzed in order to explain the Pareto coefficient by economic variables. In hierarchy models, it is found that the rate of variation in the productivity of cities and that in the probability of emergence of cities can explain the Pareto coefficient. In stochastic models, the productivity of cities is found to explain the Pareto coefficient. New city-size distribution functions, in which the Pareto coefficient is decomposed by economic variables, are estimated." excerpt

Sediment pore water distribution coefficients of PCB congeners in enriched black carbon sediment

International Nuclear Information System (INIS)

Martinez, Andres; O'Sullivan, Colin; Reible, Danny; Hornbuckle, Keri C.

2013-01-01

More than 2300 sediment pore water distribution coefficients (K PCBids ) of 93 polychlorinated biphenyls (PCBs) were measured and modeled from sediments from Indiana Harbor and Ship Canal. K PCBids were calculated from previously reported bulk sediment values and newly analyzed pore water. PCBs in pore waters were measured using SPME PDMS-fiber and ∑PCB ranged from 41 to 1500 ng L −1 . The resulting K PCBids were ∼1 log unit lower in comparison to other reported values. A simple model for the K PCBid consisted of the product of the organic carbon fraction and the octanol–water partition coefficient and provided an excellent prediction for the measured values, with a mean square error of 0.09 ± 0.06. Although black carbon content is very high in these sediments and was expected to play an important role in the distribution of PCBs, no improvement was obtained when a two-carbon model was used. -- Highlights: •PCB sediment-pore water distribution coefficients were measured and modeled. •Distribution coefficients were lower in comparison to other reported values. •Organic carbon fraction times the K OW yielded the best prediction model. •The incorporation of black carbon into a model did not improve the results. -- The organic carbon fraction times the octanol–water partition coefficient yielded the best prediction model for the sediment pore water distribution coefficient of PCBs

Procedures and apparatus for measuring diffusion and distribution coefficients in compacted clays

Energy Technology Data Exchange (ETDEWEB)

Hume, H B

1993-12-01

Diffusion and distribution coefficients are needed to assess the migration of radionuclides through the compacted clay-based buffer and backfill materials proposed for use in a nuclear fuel waste disposal vault. This report describes the techniques used to measure these coefficients. Both steady-state and transient diffusion experiments are discussed. The procedures used to prepare the clay plug, assemble the cell, conduct the experiment and calculate the results are described. In addition, methods for obtaining distribution coefficients for radionuclides on both loose and compacted clays are discussed. (author). 18 refs., 3 tabs., 16 figs.

Procedures and apparatus for measuring diffusion and distribution coefficients in compacted clays

International Nuclear Information System (INIS)

Hume, H.B.

1993-12-01

Diffusion and distribution coefficients are needed to assess the migration of radionuclides through the compacted clay-based buffer and backfill materials proposed for use in a nuclear fuel waste disposal vault. This report describes the techniques used to measure these coefficients. Both steady-state and transient diffusion experiments are discussed. The procedures used to prepare the clay plug, assemble the cell, conduct the experiment and calculate the results are described. In addition, methods for obtaining distribution coefficients for radionuclides on both loose and compacted clays are discussed. (author). 18 refs., 3 tabs., 16 figs

The stochastic distribution of available coefficient of friction on quarry tiles for human locomotion.

Science.gov (United States)

Chang, Wen-Ruey; Matz, Simon; Chang, Chien-Chi

2012-01-01

The available coefficient of friction (ACOF) for human locomotion is the maximum coefficient of friction that can be supported without a slip at the shoe and floor interface. A statistical model was introduced to estimate the probability of slip by comparing the ACOF with the required coefficient of friction, assuming that both coefficients have stochastic distributions. This paper presents an investigation of the stochastic distributions of the ACOF of quarry tiles under dry, water and glycerol conditions. One hundred friction measurements were performed on a walkway under the surface conditions of dry, water and 45% glycerol concentration. The Kolmogorov-Smirnov goodness-of-fit test was used to determine if the distribution of the ACOF was a good fit with the normal, log-normal and Weibull distributions. The results indicated that the ACOF appears to fit the normal and log-normal distributions better than the Weibull distribution for the water and glycerol conditions. However, no match was found between the distribution of ACOF under the dry condition and any of the three continuous distributions evaluated. Based on limited data, a normal distribution might be more appropriate due to its simplicity, practicality and familiarity among the three distributions evaluated.

Measurement and prediction of aromatic solute distribution coefficients for aqueous-organic solvent systems. Final report

Energy Technology Data Exchange (ETDEWEB)

Campbell, J.R.; Luthy, R.G.

1984-06-01

Experimental and modeling activities were performed to assess techniques for measurement and prediction of distribution coefficients for aromatic solutes between water and immiscible organic solvents. Experiments were performed to measure distribution coefficients in both clean water and wastewater systems, and to assess treatment of a wastewater by solvent extraction. The theoretical portions of this investigation were directed towards development of techniques for prediction of solute-solvent/water distribution coefficients. Experiments were performed to assess treatment of a phenolic-laden coal conversion wastewater by solvent extraction. The results showed that solvent extraction for recovery of phenolic material offered several wastewater processing advantages. Distribution coefficients were measured in clean water and wastewater systems for aromatic solutes of varying functionality with different solvent types. It was found that distribution coefficients for these compounds in clean water systems were not statistically different from distribution coefficients determined in a complex coal conversion process wastewater. These and other aromatic solute distribution coefficient data were employed for evaluation of modeling techniques for prediction of solute-solvent/water distribution coefficients. Eight solvents were selected in order to represent various chemical classes: toluene and benzene (aromatics), hexane and heptane (alkanes), n-octanol (alcohols), n-butyl acetate (esters), diisopropyl ether (ethers), and methylisobutyl ketone (ketones). The aromatic solutes included: nonpolar compounds such as benzene, toluene and naphthalene, phenolic compounds such as phenol, cresol and catechol, nitrogenous aromatics such as aniline, pyridine and aminonaphthalene, and other aromatic solutes such as naphthol, quinolinol and halogenated compounds. 100 references, 20 figures, 34 tables.

The rate coefficients of unimolecular reactions in the systems with power-law distributions

Science.gov (United States)

Yin, Cangtao; Guo, Ran; Du, Jiulin

2014-08-01

The rate coefficient formulae of unimolecular reactions are generalized to the systems with the power-law distributions based on nonextensive statistics, and the power-law rate coefficients are derived in the high and low pressure limits, respectively. The numerical analyses are made of the rate coefficients as functions of the ν-parameter, the threshold energy, the temperature and the number of degrees of freedom. We show that the new rate coefficients depend strongly on the ν-parameter different from one (thus from a Boltzmann-Gibbs distribution). Two unimolecular reactions, CH3CO→CH3+CO and CH3NC→CH3CN, are taken as application examples to calculate their power-law rate coefficients, which obtained with the ν-parameters slightly different from one can be exactly in agreement with all the experimental studies on these two reactions in the given temperature ranges.

Distribution coefficients for plutonium and americium on particulates in aquatic environments

International Nuclear Information System (INIS)

Sanchez, A.L.; Schell, W.R.; Sibley, T.H.

1982-01-01

The distribution coefficients of two transuranic elements, plutonium and americium, were measured experimentally in laboratory systems of selected freshwater, estuarine, and marine environments. Gamma-ray emitting isotopes of these radionuclides, 237 Pu and 241 Am, were significantly greater than the sorption Ksub(d) values, suggesting some irreversibility in the sorption of these radionuclides onto sediments. The effects of pH and of sediment concentration on the distribution coefficients were also investigated. There were significant changes in the Ksub(d) values as these parameters were varied. Experiments using sterilized and nonsterilized samples for some of the sediment/water systems indicate possible bacterial effects on Ksub(d) values. (author)

Measurement of the distribution coefficient between soil and Cesium-137

International Nuclear Information System (INIS)

Tejada V, S.; Hernandez P, M.

1996-01-01

The measurement of the distribution coefficient of Cs-137 is currently performed by batch method between radioisotope solution and which was collected from the Mexican Disposal Site, near the town of Maquixco, in the state of Mexico. The Kd values were obtained in activity concentration of Cs-137 of 100 Bq. The solution is shaken for seven days at 25 o C when the maximum amount of radionuclide is absorbed by the soil. The radionuclide in solution is measured by gamma spectrometry. The results obtained from batch method show that the distribution coefficients were from 144 to 660 ml/g for fine soil particles. This work is currently done as part of the site characterization studies for the disposal of low level rad-waste. (authors). 10 refs., 2 tabs

Estimation of the effective distribution coefficient from the solubility constant

International Nuclear Information System (INIS)

Wang, Yug-Yea; Yu, C.

1994-01-01

An updated version of RESRAD has been developed by Argonne National Laboratory for the US Department of Energy to derive site-specific soil guidelines for residual radioactive material. In this updated version, many new features have been added to the, RESRAD code. One of the options is that a user can input a solubility constant to limit the leaching of contaminants. The leaching model used in the code requires the input of an empirical distribution coefficient, K d , which represents the ratio of the solute concentration in soil to that in solution under equilibrium conditions. This paper describes the methodology developed to estimate an effective distribution coefficient, Kd, from the user-input solubility constant and the use of the effective K d for predicting the leaching of contaminants

Estimates of the Sampling Distribution of Scalability Coefficient H

Science.gov (United States)

Van Onna, Marieke J. H.

2004-01-01

Coefficient "H" is used as an index of scalability in nonparametric item response theory (NIRT). It indicates the degree to which a set of items rank orders examinees. Theoretical sampling distributions, however, have only been derived asymptotically and only under restrictive conditions. Bootstrap methods offer an alternative possibility to…

A methodology to quantify the stochastic distribution of friction coefficient required for level walking.

Science.gov (United States)

Chang, Wen-Ruey; Chang, Chien-Chi; Matz, Simon; Lesch, Mary F

2008-11-01

The required friction coefficient is defined as the minimum friction needed at the shoe and floor interface to support human locomotion. The available friction is the maximum friction coefficient that can be supported without a slip at the shoe and floor interface. A statistical model was recently introduced to estimate the probability of slip and fall incidents by comparing the available friction with the required friction, assuming that both the available and required friction coefficients have stochastic distributions. This paper presents a methodology to investigate the stochastic distributions of the required friction coefficient for level walking. In this experiment, a walkway with a layout of three force plates was specially designed in order to capture a large number of successful strikes without causing fatigue in participants. The required coefficient of friction data of one participant, who repeatedly walked on this walkway under four different walking conditions, is presented as an example of the readiness of the methodology examined in this paper. The results of the Kolmogorov-Smirnov goodness-of-fit test indicated that the required friction coefficient generated from each foot and walking condition by this participant appears to fit the normal, log-normal or Weibull distributions with few exceptions. Among these three distributions, the normal distribution appears to fit all the data generated with this participant. The average of successful strikes for each walk achieved with three force plates in this experiment was 2.49, ranging from 2.14 to 2.95 for each walking condition. The methodology and layout of the experimental apparatus presented in this paper are suitable for being applied to a full-scale study.

Study of distribution coefficients of admixtures in tellurium

International Nuclear Information System (INIS)

Kuchar, L.; Drapala, J.; Kuchar, L. jr.

1986-01-01

Limit areas of tellurium-admixture binary systems were studied and the values determined of steady-state distribution coefficients of admixtures. A second order polynomial was used to express equations of solidus and liquidus curves for Te-Se, Te-S, Te-Hg systems; the curves are graphically represented. The most effective method for preparing high-purity tellurium is zonal melting with material removal. (M.D.). 4 figs., 4 tabs., 16 refs

Distribution of temperature coefficient density for muons in the atmosphere

Directory of Open Access Journals (Sweden)

Kuzmenko V.S.

2017-12-01

Full Text Available To date, several dozens of new muon detectors have been built. When studying cosmic-ray intensity variations with these detectors, located deep in the atmosphere, it is necessary to calculate all characteristics, including the distribution of temperature coefficient density for muons in the atmosphere, taking into account their specific geometry. For this purpose, we calculate the density of temperature coefficients of muon intensity in the atmosphere at various zenith angles of detection at sea level and at various depths underground for different absorption ranges of primary protons and pions in the atmosphere.

A review of the distribution coefficients of trace elements in soils: influence of sorption system, element characteristics, and soil colloidal properties.

Science.gov (United States)

Shaheen, Sabry M; Tsadilas, Christos D; Rinklebe, Jörg

2013-12-01

Knowledge about the behavior and reactions of separate soil components with trace elements (TEs) and their distribution coefficients (Kds) in soils is a key issue in assessing the mobility and retention of TEs. Thus, the fate of TEs and the toxic risk they pose depend crucially on their Kd in soil. This article reviews the Kd of TEs in soils as affected by the sorption system, element characteristics, and soil colloidal properties. The sorption mechanism, determining factors, favorable conditions, and competitive ions on the sorption and Kd of TEs are also discussed here. This review demonstrates that the Kd value of TEs does not only depend on inorganic and organic soil constituents, but also on the nature and characteristics of the elements involved as well as on their competition for sorption sites. The Kd value of TEs is mainly affected by individual or competitive sorption systems. Generally, the sorption in competitive systems is lower than in mono-metal sorption systems. More strongly sorbed elements, such as Pb and Cu, are less affected by competition than mobile elements, such as Cd, Ni, and Zn. The sorption preference exhibited by soils for elements over others may be due to: (i) the hydrolysis constant, (ii) the atomic weight, (iii) the ionic radius, and subsequently the hydrated radius, and (iv) its Misono softness value. Moreover, element concentrations in the test solution mainly affect the Kd values. Mostly, values of Kd decrease as the concentration of the included cation increases in the test solution. Additionally, the Kd of TEs is controlled by the sorption characteristics of soils, such as pH, clay minerals, soil organic matter, Fe and Mn oxides, and calcium carbonate. However, more research is required to verify the practical utilization of studying Kd of TEs in soils as a reliable indicator for assessing the remediation process of toxic metals in soils and waters. © 2013 Elsevier B.V. All rights reserved.

Critical electrode size in measurement of d33 coefficient of films via spatial distribution of piezoelectric displacement

International Nuclear Information System (INIS)

Wang Zhihong; Miao Jianmin

2008-01-01

Spatial distributions of piezoelectric displacement response across the top electrode have been used in this paper to measure the piezoelectric coefficient d 33 of films based on the converse piezoelectric effect. The technical details and features of a scanning laser Doppler vibrometer have been summarized and discussed for accurately obtaining the spatial displacement distributions. Three definitions, including the apparent, the effective and the constrained piezoelectric coefficient d 33 of films, have been clarified and used to better understand the fundamental phenomenon behind the measured displacement distributions. Finite element analysis reveals that both the apparent and the effective piezoelectric coefficients depend on the electrode radius of test capacitor as well as film thickness. However, there exists a critical electrode size for apparent piezoelectric coefficients and a critical test capacitor aspect ratio for effective piezoelectric coefficient. Beyond their respective critical values, both coefficients converge to the constrained piezoelectric coefficient irrespective of film thickness. The finding of the critical electric size makes it possible to consistently measure the constrained piezoelectric coefficient of films by using the spatial distributions of the piezoelectric displacement response and becomes the fundamental criterion of this measurement method

Standard test method for distribution coefficients of inorganic species by the batch method

CERN Document Server

American Society for Testing and Materials. Philadelphia

2010-01-01

1.1 This test method covers the determination of distribution coefficients of chemical species to quantify uptake onto solid materials by a batch sorption technique. It is a laboratory method primarily intended to assess sorption of dissolved ionic species subject to migration through pores and interstices of site specific geomedia. It may also be applied to other materials such as manufactured adsorption media and construction materials. Application of the results to long-term field behavior is not addressed in this method. Distribution coefficients for radionuclides in selected geomedia are commonly determined for the purpose of assessing potential migratory behavior of contaminants in the subsurface of contaminated sites and waste disposal facilities. This test method is also applicable to studies for parametric studies of the variables and mechanisms which contribute to the measured distribution coefficient. 1.2 The values stated in SI units are to be regarded as standard. No other units of measurement a...

Study on the distribution coefficient during environmental impact evaluation in Chinese inland nuclear power plants

International Nuclear Information System (INIS)

Xu Haifeng; Shang Zhaorong; Chen Fangqiang

2012-01-01

Description the radionuclide distribution coefficient of the important factors in the river sediment systems, at home and abroad the main method of measuring the K d value and progress in China's inland nuclear power plant environmental impact assessment of workers to carry out the distribution coefficient K d value measurement ideas put forward recommendations. (authors)

Empirical Sampling Distributions of Equating Coefficients for Graded and Nominal Response Instruments.

Science.gov (United States)

Baker, Frank B.

1997-01-01

Examined the sampling distributions of equating coefficients produced by the characteristic curve method for tests using graded and nominal response scoring using simulated data. For both models and across all three equating situations, the sampling distributions were generally bell-shaped and peaked, and occasionally had a small degree of…

On the construction of bivariate exponential distributions with an arbitrary correlation coefficient

DEFF Research Database (Denmark)

Bladt, Mogens; Nielsen, Bo Friis

In this paper we use a concept of multivariate phase-type distributions to define a class of bivariate exponential distributions. This class has the following three appealing properties. Firstly, we may construct a pair of exponentially distributed random variables with any feasible correlation...... coefficient (also negative). Secondly, the class satisfies that any linear combination (projection) of the marginal random variables is a phase {type distributions, The latter property is potentially important for the development hypothesis testing in linear models. Thirdly, it is very easy to simulate...

Determination of distribution coefficients of some natural radionuclides (U, Ra, Pb, Po) between different types of Syrian soils and their solutions

International Nuclear Information System (INIS)

Al-Masri, M. S.; Al-Hamwi, A.; Amin, Y.; Al-Akel, B.

2009-11-01

In this study, distribution coefficients of some natural radionuclides ( 226 Ra, U, 210 Pb and 210 Po) between different types of soils in Syria and their solutions were determined. The distribution coefficients values ranged from (164-1933, 280-1722, 350-4749 and 101-117) l kg - 1 for 226 Ra, U, 210 Pb and 210 Po, respectively at pH = 4.0. While, the distribution coefficients values ranged from (207-6706, 673-2397, 149-2147 and 103- 292) l kg - 1 for 226 Ra, U, 210 Pb and 210 Po, respectively at pH = 5.5. In addition, the distribution coefficients values ranged from (167-1707, 126- 1239, 44-1122 and 125-1475) l kg - 1 for 226 Ra, U, 210 Pb and 210 Po, respectively at pH = 7.0. Moreover, the results showed that 210 Po distribution coefficients had the maximum values at pH 7. While 210 Pb distribution coefficients had the minimum values at same pH. In addition to, U distribution coefficients had the maximum values at pH 5.5. On the other hand, the effect of soil mineral content, CEC, ECE, pH and soluble ions on the distribution coefficients were investigated. In general, the results showed that there are logarithmic relationships between studied radionuclide activity in the soil and their distribution coefficients in all soil types (R 2 ranged from 0.59 to 1.00 at pH 4.0). On the other hand, there were no relationships between the distribution coefficients and soil pH. (authors)

Predicting cyclohexane/water distribution coefficients for the SAMPL5 challenge using MOSCED and the SMD solvation model

Science.gov (United States)

Diaz-Rodriguez, Sebastian; Bozada, Samantha M.; Phifer, Jeremy R.; Paluch, Andrew S.

2016-11-01

We present blind predictions using the solubility parameter based method MOSCED submitted for the SAMPL5 challenge on calculating cyclohexane/water distribution coefficients at 298 K. Reference data to parameterize MOSCED was generated with knowledge only of chemical structure by performing solvation free energy calculations using electronic structure calculations in the SMD continuum solvent. To maintain simplicity and use only a single method, we approximate the distribution coefficient with the partition coefficient of the neutral species. Over the final SAMPL5 set of 53 compounds, we achieved an average unsigned error of 2.2± 0.2 log units (ranking 15 out of 62 entries), the correlation coefficient ( R) was 0.6± 0.1 (ranking 35), and 72± 6 % of the predictions had the correct sign (ranking 30). While used here to predict cyclohexane/water distribution coefficients at 298 K, MOSCED is broadly applicable, allowing one to predict temperature dependent infinite dilution activity coefficients in any solvent for which parameters exist, and provides a means by which an excess Gibbs free energy model may be parameterized to predict composition dependent phase-equilibrium.

The stochastic distribution of available coefficient of friction for human locomotion of five different floor surfaces.

Science.gov (United States)

Chang, Wen-Ruey; Matz, Simon; Chang, Chien-Chi

2014-05-01

The maximum coefficient of friction that can be supported at the shoe and floor interface without a slip is usually called the available coefficient of friction (ACOF) for human locomotion. The probability of a slip could be estimated using a statistical model by comparing the ACOF with the required coefficient of friction (RCOF), assuming that both coefficients have stochastic distributions. An investigation of the stochastic distributions of the ACOF of five different floor surfaces under dry, water and glycerol conditions is presented in this paper. One hundred friction measurements were performed on each floor surface under each surface condition. The Kolmogorov-Smirnov goodness-of-fit test was used to determine if the distribution of the ACOF was a good fit with the normal, log-normal and Weibull distributions. The results indicated that the ACOF distributions had a slightly better match with the normal and log-normal distributions than with the Weibull in only three out of 15 cases with a statistical significance. The results are far more complex than what had heretofore been published and different scenarios could emerge. Since the ACOF is compared with the RCOF for the estimate of slip probability, the distribution of the ACOF in seven cases could be considered a constant for this purpose when the ACOF is much lower or higher than the RCOF. A few cases could be represented by a normal distribution for practical reasons based on their skewness and kurtosis values without a statistical significance. No representation could be found in three cases out of 15. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

Distribution Coefficient Kd of Cesium in Soils from Areas in Perak

International Nuclear Information System (INIS)

Azian Hashim; Mohd Suhaimi Hamzah; Shamsiah Abdul Rahman; Nazaratul Ashifa Abdullah Salim; Md Suhaimi Elias; Shakirah Shukor; Muhd Azfar Azman; Siti Aminah Omar

2015-01-01

This is the paper reports on the study of distribution coefficient or Kd value in soil collected from the Western of Perak, which is Manjung, Setiawan, and Lahat with two different depths using lab batch method. Particle sizes were analyzed using the conventional technique known as pipette method. pH of the sample were 2-3. Determinations for cesium were performed using Inductively Coupled Plasma-Mass (ICP-MS). From the results, distribution factor for cesium, Kd value, was found to be influenced by the particle size of soil. (author)

On the Construction of Bivariate Exponential Distributions with an Arbitrary Correlation Coefficient

DEFF Research Database (Denmark)

Bladt, Mogens; Nielsen, Bo Friis

2010-01-01

coefficient (also negative). Secondly, the class satisfies that any linear combination (projection) of the marginal random variables is a phase-type distribution. The latter property is partially important for the development of hypothesis testing in linear models. Finally, it is easy to simulate...

A simple approximation to the bivariate normal distribution with large correlation coefficient

NARCIS (Netherlands)

Albers, Willem/Wim; Kallenberg, W.C.M.

1994-01-01

The bivariate normal distribution function is approximated with emphasis on situations where the correlation coefficient is large. The high accuracy of the approximation is illustrated by numerical examples. Moreover, exact upper and lower bounds are presented as well as asymptotic results on the

Transformation of correlation coefficients between normal and lognormal distribution and implications for nuclear applications

International Nuclear Information System (INIS)

Žerovnik, Gašper; Trkov, Andrej; Smith, Donald L.; Capote, Roberto

2013-01-01

Inherently positive parameters with large relative uncertainties (typically ≳30%) are often considered to be governed by the lognormal distribution. This assumption has the practical benefit of avoiding the possibility of sampling negative values in stochastic applications. Furthermore, it is typically assumed that the correlation coefficients for comparable multivariate normal and lognormal distributions are equivalent. However, this ideal situation is approached only in the linear approximation which happens to be applicable just for small uncertainties. This paper derives and discusses the proper transformation of correlation coefficients between both distributions for the most general case which is applicable for arbitrary uncertainties. It is seen that for lognormal distributions with large relative uncertainties strong anti-correlations (negative correlations) are mathematically forbidden. This is due to the asymmetry that is an inherent feature of these distributions. Some implications of these results for practical nuclear applications are discussed and they are illustrated with examples in this paper. Finally, modifications to the ENDF-6 format used for representing uncertainties in evaluated nuclear data libraries are suggested, as needed to deal with this issue

Transformation of correlation coefficients between normal and lognormal distribution and implications for nuclear applications

Energy Technology Data Exchange (ETDEWEB)

Žerovnik, Gašper, E-mail: gasper.zerovnik@ijs.si [Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Trkov, Andrej, E-mail: andrej.trkov@ijs.si [Jožef Stefan Institute, Jamova cesta 39, SI-1000 Ljubljana (Slovenia); Smith, Donald L., E-mail: donald.l.smith@anl.gov [Argonne National Laboratory, 1710 Avenida del Mundo, Coronado, CA 92118-3073 (United States); Capote, Roberto, E-mail: roberto.capotenoy@iaea.org [NAPC–Nuclear Data Section, International Atomic Energy Agency, PO Box 100, Vienna-A-1400 (Austria)

2013-11-01

Inherently positive parameters with large relative uncertainties (typically ≳30%) are often considered to be governed by the lognormal distribution. This assumption has the practical benefit of avoiding the possibility of sampling negative values in stochastic applications. Furthermore, it is typically assumed that the correlation coefficients for comparable multivariate normal and lognormal distributions are equivalent. However, this ideal situation is approached only in the linear approximation which happens to be applicable just for small uncertainties. This paper derives and discusses the proper transformation of correlation coefficients between both distributions for the most general case which is applicable for arbitrary uncertainties. It is seen that for lognormal distributions with large relative uncertainties strong anti-correlations (negative correlations) are mathematically forbidden. This is due to the asymmetry that is an inherent feature of these distributions. Some implications of these results for practical nuclear applications are discussed and they are illustrated with examples in this paper. Finally, modifications to the ENDF-6 format used for representing uncertainties in evaluated nuclear data libraries are suggested, as needed to deal with this issue.

Engineering magnetic polariton system with distributed coefficients: Applications to soliton management

International Nuclear Information System (INIS)

Kuetche, Victor K.; Nguepjouo, Francis T.; Kofane, Timoleon C.

2014-01-01

In the wake of the recent design of a powerful method for generating higher-dimensional evolution systems with distributed coefficients Kuetche (2014) [15] illustrated on the dynamics of the current-fed membrane of zero Young’s modulus, we construct the general Lax-representation of a new higher-dimensional coupled evolution equations with varying coefficients. Discussing the physical meanings of these equations, we show that the coupled system above describes the propagation of magnetic polaritons within saturated ferrites, resulting structurally from the fast-near adiabatic magnetization dynamics combined to the Maxwell’s equations. Accordingly, we address some practical issues of the nonautonomous soliton managements underlying in the fast remagnetization process of data inputs within magnetic memory devices

Stochastic distribution of the required coefficient of friction for level walking--an in-depth study.

Science.gov (United States)

Chang, Wen-Ruey; Matz, Simon; Chang, Chien-Chi

2012-01-01

This study investigated the stochastic distribution of the required coefficient of friction (RCOF) which is a critical element for estimating slip probability. Fifty participants walked under four walking conditions. The results of the Kolmogorov-Smirnov two-sample test indicate that 76% of the RCOF data showed a difference in distribution between both feet for the same participant under each walking condition; the data from both feet were kept separate. The results of the Kolmogorov-Smirnov goodness-of-fit test indicate that most of the distribution of the RCOF appears to have a good match with the normal (85.5%), log-normal (84.5%) and Weibull distributions (81.5%). However, approximately 7.75% of the cases did not have a match with any of these distributions. It is reasonable to use the normal distribution for representation of the RCOF distribution due to its simplicity and familiarity, but each foot had a different distribution from the other foot in 76% of cases. The stochastic distribution of the required coefficient of friction (RCOF) was investigated for use in a statistical model to improve the estimate of slip probability in risk assessment. The results indicate that 85.5% of the distribution of the RCOF appears to have a good match with the normal distribution.

Are distribution coefficients measured from batch experiments meaningful for quantifying retention in compacted material?

Energy Technology Data Exchange (ETDEWEB)

Goutelard, F.; Charles, Y.; Page, J. [CEA/DEN/DPC/SECR/L3MR batiment 450, 91191 Gif sur Yvette (France)

2005-07-01

Full text of publication follows: To quantify the ability of a clayey material to act as a barrier for radionuclides migration, reliable data on retention properties must be available. The most common method for determining the distribution coefficient, quantifying the radionuclide adsorption, is the batch technique applied to powdered solid. Are these data meaningful for highly compacted minerals? This question is still under debate in literature [1,2]. The aim of the present study is to compare distribution coefficient (KD) value for Cs and Ni onto compacted and dispersed for both Bentonite MX80 and Callovo-Oxfordian clayey material in a simulated site water. Firstly, classical batch sorption experiments are carried on dispersed materials pre-conditioned with the simulated site water at pH 7.3. Radiotracer {sup 137}Cs and {sup 58}Ni are used to investigate the constant-pH isotherm sorption. The bottleneck for measuring distribution coefficient onto highly compacted material lies in a careful monitoring of chemical conditions because they are driven by diffusion processes. For this study, we have chosen to use in-diffusion experiments [3]. Sample size is optimized to reach for high retention level (300 mL/g) the steady state in a reasonable time (3 to 6 month). In order to describe the response surface of compacted distribution coefficient on bentonite MX80, a 2 variables Doehlert matrix has been chosen. In this experimental design, the two variables are density and dispersed distribution coefficient. Bentonite is pre-conditioning before compaction to a density ranging from 1.2 to 1.85 kg/l. The pellet is confined in a cylindrical stainless steel filter (150 {mu}L) closed to both ends. The cell is placed in a tightly closed bottle containing the working solution. After a re-equilibration period (at least 3 weeks), {sup 133}Cs and {sup 59}Ni stable isotope are introduced for monitoring the KD level (between 150 mL/g to 330 mL/g). Radiotracer {sup 137}Cs and {sup 58

Are distribution coefficients measured from batch experiments meaningful for quantifying retention in compacted material?

International Nuclear Information System (INIS)

Goutelard, F.; Charles, Y.; Page, J.

2005-01-01

Full text of publication follows: To quantify the ability of a clayey material to act as a barrier for radionuclides migration, reliable data on retention properties must be available. The most common method for determining the distribution coefficient, quantifying the radionuclide adsorption, is the batch technique applied to powdered solid. Are these data meaningful for highly compacted minerals? This question is still under debate in literature [1,2]. The aim of the present study is to compare distribution coefficient (KD) value for Cs and Ni onto compacted and dispersed for both Bentonite MX80 and Callovo-Oxfordian clayey material in a simulated site water. Firstly, classical batch sorption experiments are carried on dispersed materials pre-conditioned with the simulated site water at pH 7.3. Radiotracer 137 Cs and 58 Ni are used to investigate the constant-pH isotherm sorption. The bottleneck for measuring distribution coefficient onto highly compacted material lies in a careful monitoring of chemical conditions because they are driven by diffusion processes. For this study, we have chosen to use in-diffusion experiments [3]. Sample size is optimized to reach for high retention level (300 mL/g) the steady state in a reasonable time (3 to 6 month). In order to describe the response surface of compacted distribution coefficient on bentonite MX80, a 2 variables Doehlert matrix has been chosen. In this experimental design, the two variables are density and dispersed distribution coefficient. Bentonite is pre-conditioning before compaction to a density ranging from 1.2 to 1.85 kg/l. The pellet is confined in a cylindrical stainless steel filter (150 μL) closed to both ends. The cell is placed in a tightly closed bottle containing the working solution. After a re-equilibration period (at least 3 weeks), 133 Cs and 59 Ni stable isotope are introduced for monitoring the KD level (between 150 mL/g to 330 mL/g). Radiotracer 137 Cs and 58 Ni are used to quantify the

Coefficients of distribution and accumulation of K, Rb, Cs and 137Cs in the intensive poultry breeding cycle

International Nuclear Information System (INIS)

Djuric, G.; Ajdacic, N.; Institut za Nuklearne Nauke Boris Kidric, Belgrade

1984-01-01

The concentration of K,Rb,Cs and the activity level of Cs-137 in samples from the intensive poultry breeding cycle (feed, meat, eggs), under the condition of chronic alimentary contamination is presented. Concentrations of Cs and Rb were determined by non-destructive neutron activation analysis, concentration of K by atomic absorption flame photometry and activity of Cs-137 by gamma spectrometric analysis. On the basis of these results, coefficients of distribution and accumulation were calculated. The distribution coefficients of the analysed stable isotopes in meat have values close to 1, whereas for various parts of egg these coefficients vary between 0.5 and 1.5. Significant differences in Cs-137 distribution in various parts of egg were established. The values of accumulation coefficients indicate that all analysed elements selectively accumulate in the meat of young birds (broilers), and Cs-137 accumulates in the egg white as well. (orig.)

Spatial distribution of coefficients for determination of global radiation in Serbia

Directory of Open Access Journals (Sweden)

Nikolić Jugoslav L.

2012-01-01

Full Text Available The aim of this paper is a creation of the spatial distribution of the corresponding coefficients for the indirect determination of global radiation using all direct measurements data of this shortwave radiation balance component in Serbia in the standard climate period (1961-1990. Based on the global radiation direct measurements data recorded in the past and routine measurements/observations of cloudiness and sunshine duration, the spatial distribution coefficients maps required for calculation of global radiation were produced on the basis of sunshine/cloudiness in an arbitrary point on the territory of Serbia. Besides, a specific verification of the proposed empirical formula was performed. This paper contributes to a wide range of practical applications as direct measurements of global radiation are relatively rare, and are not carried out in Serbia today. Significant application is possible in the domain of renewable energy sources. The development of method for determination of the global radiation has an importance from the aspect of the environmental protection; however it also has an economic importance through applications in numerous commercial projects, as it does not require special measurements or additional financial investments.

Ionization constants by curve fitting: determination of partition and distribution coefficients of acids and bases and their ions.

Science.gov (United States)

Clarke, F H; Cahoon, N M

1987-08-01

A convenient procedure has been developed for the determination of partition and distribution coefficients. The method involves the potentiometric titration of the compound, first in water and then in a rapidly stirred mixture of water and octanol. An automatic titrator is used, and the data is collected and analyzed by curve fitting on a microcomputer with 64 K of memory. The method is rapid and accurate for compounds with pKa values between 4 and 10. Partition coefficients can be measured for monoprotic and diprotic acids and bases. The partition coefficients of the neutral compound and its ion(s) can be determined by varying the ratio of octanol to water. Distribution coefficients calculated over a wide range of pH values are presented graphically as "distribution profiles". It is shown that subtraction of the titration curve of solvent alone from that of the compound in the solvent offers advantages for pKa determination by curve fitting for compounds of low aqueous solubility.

A Correction of Random Incidence Absorption Coefficients for the Angular Distribution of Acoustic Energy under Measurement Conditions

DEFF Research Database (Denmark)

Jeong, Cheol-Ho

2009-01-01

Most acoustic measurements are based on an assumption of ideal conditions. One such ideal condition is a diffuse and reverberant field. In practice, a perfectly diffuse sound field cannot be achieved in a reverberation chamber. Uneven incident energy density under measurement conditions can cause...... discrepancies between the measured value and the theoretical random incidence absorption coefficient. Therefore the angular distribution of the incident acoustic energy onto an absorber sample should be taken into account. The angular distribution of the incident energy density was simulated using the beam...... tracing method for various room shapes and source positions. The averaged angular distribution is found to be similar to a Gaussian distribution. As a result, an angle-weighted absorption coefficient was proposed by considering the angular energy distribution to improve the agreement between...

Estimation of the distribution coefficient by combined application of two different methods

International Nuclear Information System (INIS)

Vogl, G.; Gerstenbrand, F.

1982-01-01

A simple, non-invasive method is presented which permits determination of the rBCF and, in addition, of the distribution coefficient of the grey matter. The latter, which is closely correlated with the cerebral metabolism, has only been determined in vitro so far. The new method will be a means to check its accuracy. (orig.) [de

Sorption behavior of cesium onto bentonite colloid

International Nuclear Information System (INIS)

Iijima, Kazuki; Masuda, Tsuguya; Tomura, Tsutomu

2004-01-01

It is considered that bentonite colloid might be generated from bentonite which will be used as buffer material in geological disposal system, and can facilitate the migration of radionuclides by means of sorption. In order to examine this characteristic, sorption and desorption experiments of Cs onto bentonite colloid were carried out to obtain its distribution coefficient (Kd) and information on the reversibility of its sorption. In addition, particle size distribution and shape of colloid were investigated and their effect on the sorption behavior was discussed. Kds for Cs were around 20 m 3 /kg for sorption and 30 m 3 /kg for desorption, in which sorbed Cs was desorbed by 8.4x10 -4 mol/l of NaCl solution. These values did not show any dependencies on Cs concentration and duration of sorption and desorption. The first 20% of sorbed Cs was desorbed reversibly at least. Most of colloidal particles were larger than 200 nm and TEM micrographs showed they had only several sheets of the clay crystal. Obtained Kds for colloidal bentonite were larger than those for powdered bentonite. This can be caused by difference of competing ions in the solution, characteristics of contained smectite, or sorption site density. (author)

Apparent distribution coefficients of transuranium elements in UK coastal waters

International Nuclear Information System (INIS)

Kershaw, P.J.; Pentreath, R.J.; Harvey, B.R.; Lovett, M.B.; Boggis, S.J.

1986-01-01

The authorized inputs of low-level radioactive waste into the Irish Sea from the British Nuclear Fuels plc reprocessing plant at Sellafield may be used to advantage to study the distribution and behaviour of artificial radionuclides in the marine environment. Apparent distribution coefficients (Ksub(d)) for the transuranium elements Np, Pu, Am and Cm have been determined by the analysis of environmental samples collected from UK coastal waters. The sampling methodology for obtaining suspended sediment-seawater Ksub(d)s by filtration is described and critically evaluated. Artefacts may be introduced in the sample collection stage. Ksub(d) values have also been determined for seabed sediment-interstitial waters and the precautions taken to preserve in-situ chemical conditions are described. Variations in Ksub(d) values are discussed in relation to distance from Sellafield, suspended load, redox conditions and oxidation state changes. (author)

Distribution of physicians and hospital beds based on Gini coefficient and Lorenz curve: A national survey

Directory of Open Access Journals (Sweden)

Satar Rezaei

2016-06-01

Full Text Available Introduction: Inequality is prevalent in all sectors, particularly in distribution of and access to resources in the health sector. The aim of current study was to investigate the distribution of physicians and hospital beds in Iran in 2001, 2006 and 2011. Methods: This retrospective, cross-sectional study evaluated the distribution of physicians and hospital beds in 2001, 2006 and 2011 using Gini coefficient and Lorenz curve. The required data, including the number of physicians (general practitioners and specialists, number of hospital beds and number of hospitalized patients were obtained from the statistical yearbook of Iranian Statistical Center (ISC. The data analysis was performed by DASP software. Results: The Gini Coefficients for physicians and hospital beds based on population in 2001 were 0.19 and 0.16, and based on hospitalized patients, were 0.48 and 0.37, respectively. In 2006, these values were found to be 0.18 and 0.15 based on population, and 0.21 and 0.21 based on hospitalized patients, respectively. In 2011, however, the Gini coefficients were reported to be 0.16 and 0.13 based on population, and 0.47 and 0.37 based on hospitalized patients, respectively. Although distribution status had improved in 2011compared with 2001 in terms of population and number of hospitalized patients, there was more inequality in distribution based on the number of hospitalized patients than based on population. Conclusion: This study indicated that inequality in distribution of physicians and hospital beds was declined in 2011 compared with 2001. This distribution was based on the population, so it is suggested that, in allocation of resource, the health policymakers consider such need indices as the pattern of diseases and illness-prone areas, number of inpatients, and mortality.

Research on sorption behavior of radionuclides under shallow land environment. Mechanism and standard methodologies for measurement of distribution coefficients of radionuclides

International Nuclear Information System (INIS)

Sakamoto, Yoshiaki; Tanaka, Tadao; Takebe, Shinichi; Nagao, Seiya; Ogawa, Hiromichi; Komiya, Tomokazu; Hagiwara, Shigeru

2001-01-01

This study consists of two categories' research works. One is research on sorption mechanism of radionuclides with long half-life, which are Technetium-99, TRU elements and U series radionuclides, on soil and rocks, including a development of database of distribution coefficients of radionuclides. The database on the distribution coefficients of radionuclides with information about measurement conditions, such as shaking method, soil characteristics and solution composition, has been already opened to the public (JAERI-DATABASE 20001003). Another study is investigation on a standard methodology of the distribution coefficient of radionuclide on soils, rocks and engineering materials in Japan. (author)

A novel method for the investigation of liquid/liquid distribution coefficients and interface permeabilities applied to the water-octanol-drug system.

Science.gov (United States)

Stein, Paul C; di Cagno, Massimiliano; Bauer-Brandl, Annette

2011-09-01

In this work a new, accurate and convenient technique for the measurement of distribution coefficients and membrane permeabilities based on nuclear magnetic resonance (NMR) is described. This method is a novel implementation of localized NMR spectroscopy and enables the simultaneous analysis of the drug content in the octanol and in the water phase without separation. For validation of the method, the distribution coefficients at pH = 7.4 of four active pharmaceutical ingredients (APIs), namely ibuprofen, ketoprofen, nadolol, and paracetamol (acetaminophen), were determined using a classical approach. These results were compared to the NMR experiments which are described in this work. For all substances, the respective distribution coefficients found with the two techniques coincided very well. Furthermore, the NMR experiments make it possible to follow the distribution of the drug between the phases as a function of position and time. Our results show that the technique, which is available on any modern NMR spectrometer, is well suited to the measurement of distribution coefficients. The experiments present also new insight into the dynamics of the water-octanol interface itself and permit measurement of the interface permeability.

Estimation of soil-soil solution distribution coefficient of radiostrontium using soil properties.

Science.gov (United States)

Ishikawa, Nao K; Uchida, Shigeo; Tagami, Keiko

2009-02-01

We propose a new approach for estimation of soil-soil solution distribution coefficient (K(d)) of radiostrontium using some selected soil properties. We used 142 Japanese agricultural soil samples (35 Andosol, 25 Cambisol, 77 Fluvisol, and 5 others) for which Sr-K(d) values had been determined by a batch sorption test and listed in our database. Spearman's rank correlation test was carried out to investigate correlations between Sr-K(d) values and soil properties. Electrical conductivity and water soluble Ca had good correlations with Sr-K(d) values for all soil groups. Then, we found a high correlation between the ratio of exchangeable Ca to Ca concentration in water soluble fraction and Sr-K(d) values with correlation coefficient R=0.72. This pointed us toward a relatively easy way to estimate Sr-K(d) values.

Determination of distribution coefficient (Kd's) of some artificial and naturally occurring radionuclide in fresh and marine coastal water sediment

International Nuclear Information System (INIS)

Al-Masri, M. S.; Mamish, S; Haleem, M. A.

2004-12-01

Distribution coefficients of artificial and natural radionuclides in fresh and marine water sediment are used in modeling radionuclide dispersion in water system, and the radiation risk and environmental investigating of impact of radioactive emissions, due to routine operations of nuclear plants or disposal and burial of radioactive waste in the environment. In the present work, distribution coefficient of uranium, lead, polonium, radium (naturally occurring radionuclides that may be emitted into the Syrian environment by the phosphate and oil industry with relatively high concentrations) and caesium 137 and strontium 85, in fresh water sediment (Euphrates River, Orantos River and Mzzerib Lake) and marine coastal water (Lattakia, Tartous and Banias). Distribution coefficients were found to vary between (5.8-17.18)*10 3 , (2.2-8.11)*10 3 , (0.22-2.08)*10 3 , (0.16-0.19)*10 3 , (0.38-0.69)*10 3 and 49-312 for polonium, lead, uranium, radium, cesium and strontium respectively. Results have indicated that most measurement distribution coefficients in the present study were lower than those values reported in IAEA documents for marine coastal sediment. In addition, variations of Kd's with aqueous phase composition and sediment elemental and mineralogical composition and its total organic materials content have been studied, where liner correlation coefficients for each isotope with different parameters have been determined. The obtained data reported in this study can be used for radioactive contaminants dispersion and transfer in Syrian river, lake and coast to assess risks to public due to discharges of the phosphate and oil industry into the Syrian environment. (Authors)

Distribution coefficient of radionuclides on rocks for performance assessment of high-level radioactive waste repository

International Nuclear Information System (INIS)

Shibutani, Tomoki; Shibata, Masahiro; Suyama, Tadahiro

1999-11-01

Distribution coefficients of radionuclides on rocks are selected for safety assessment in the 'Second Progress Report on Research and Development for the geological disposal of HLW in Japan (H12 Report)'. The categorized types of rock are granitic rocks (crystalline and acidic rocks), basaltic rocks (crystalline and basic rocks), psammitic rocks (neogene sedimentary (soft)), and tuffaceous-pelitic rocks (pre-neogene sedimentary rocks (hard)). The types of groundwater are FRHP (fresh reducing high-pH), FRLP (fresh reducing low-pH), SRHP (saline reducing high-pH), SRLP (saline reducing low-pH), MRNP (mixing reducing neutral-pH) and FOHP (fresh oxidizing high-pH) groundwater. The elements to be surveyed are Ni, Se, Zr, Nb, Tc, Pd, Sn, Cs, Sm, Pb, Ra, Ac, Th, Pa, U, Np, Pu, Am and Cm. Distribution coefficients are collected from literatures describing batch sorption experimental results, and are selected under consideration of conservativity. (author)

TU-F-18C-05: Evaluation of a Method to Calculate Patient-Oriented MGD Coefficients Using Estimates of Glandular Tissue Distribution

International Nuclear Information System (INIS)

Porras-Chaverri, M; Galavis, P; Bakic, P; Vetter, J

2014-01-01

Purpose: Evaluate mammographic mean glandular dose (MGD) coefficients for particular known tissue distributions using a novel formalism that incorporates the effect of the heterogeneous glandular tissue distribution, by comparing them with MGD coefficients derived from the corresponding anthropomorphic computer breast phantom. Methods: MGD coefficients were obtained using MCNP5 simulations with the currently used homogeneous assumption and the heterogeneously-layered breast (HLB) geometry and compared against those from the computer phantom (ground truth). The tissue distribution for the HLB geometry was estimated using glandularity map image pairs corrected for the presence of non-glandular fibrous tissue. Heterogeneity of tissue distribution was quantified using the glandular tissue distribution index, Idist. The phantom had 5 cm compressed breast thickness (MLO and CC views) and 29% whole breast glandular percentage. Results: Differences as high as 116% were found between the MGD coefficients with the homogeneous breast core assumption and those from the corresponding ground truth. Higher differences were found for cases with more heterogeneous distribution of glandular tissue. The Idist for all cases was in the [−0.8 − +0.3] range. The use of the methods presented in this work results in better agreement with ground truth with an improvement as high as 105 pp. The decrease in difference across all phantom cases was in the [9 − 105] pp range, dependent on the distribution of glandular tissue and was larger for the cases with the highest Idist values. Conclusion: Our results suggest that the use of corrected glandularity image pairs, as well as the HLB geometry, improves the estimates of MGD conversion coefficients by accounting for the distribution of glandular tissue within the breast. The accuracy of this approach with respect to ground truth is highly dependent on the particular glandular tissue distribution studied. Predrag Bakic discloses current

AN EMPIRICAL INVESTIGATION OF THE EFFECTS OF NONNORMALITY UPON THE SAMPLING DISTRIBUTION OF THE PROJECT MOMENT CORRELATION COEFFICIENT.

Science.gov (United States)

HJELM, HOWARD; NORRIS, RAYMOND C.

THE STUDY EMPIRICALLY DETERMINED THE EFFECTS OF NONNORMALITY UPON SOME SAMPLING DISTRIBUTIONS OF THE PRODUCT MOMENT CORRELATION COEFFICIENT (PMCC). SAMPLING DISTRIBUTIONS OF THE PMCC WERE OBTAINED BY DRAWING NUMEROUS SAMPLES FROM CONTROL AND EXPERIMENTAL POPULATIONS HAVING VARIOUS DEGREES OF NONNORMALITY AND BY CALCULATING CORRELATION COEFFICIENTS…

Distribution coefficients for chemical components of a coal-oil/water system

Energy Technology Data Exchange (ETDEWEB)

Picel, K C; Stamoudis, V C; Simmons, M S

1988-09-01

Distribution coefficients (K/sub D/) were measured by equilibrating a coal oil comparative reference material (CRM-1) with water and then separating the oil and water phases. Aqueous phase concentrations were determined by direct analysis of this phase, while organic phase concentrations were determined from the original oil composition by difference. The log K/sub D/ values obtained for acidic and basic components were generally <3, while those for the neutral components ranged from 3 to 6. For aromatic hydrocarbons, strong correlations were observed between log K/sub D/ and log S/sub w/ (water solubility), and between log K/sub D/ and log K/sub o//sub w/ (octanol/water partition coefficient). Alkylated benzenes had significantly higher K/sub D/s than did unsubstituted aromatics of similar molecular weight. Examination of homologs revealed an increase of 0.307 log K/sub D/ units per additional carbon atom for polynuclear aromatic hydrocarbons having from 10 to 16 carbons. Alkyl substituent effects determined for various sets of homologs ranged from 0.391 to 0.466 log K/sub d/ units per -CH/sub 2/- group added. 38 refs., 5 figs., 7 tabs.

The Effect of Nonzero Autocorrelation Coefficients on the Distributions of Durbin-Watson Test Estimator: Three Autoregressive Models

Directory of Open Access Journals (Sweden)

Mei-Yu LEE

2014-11-01

Full Text Available This paper investigates the effect of the nonzero autocorrelation coefficients on the sampling distributions of the Durbin-Watson test estimator in three time-series models that have different variance-covariance matrix assumption, separately. We show that the expected values and variances of the Durbin-Watson test estimator are slightly different, but the skewed and kurtosis coefficients are considerably different among three models. The shapes of four coefficients are similar between the Durbin-Watson model and our benchmark model, but are not the same with the autoregressive model cut by one-lagged period. Second, the large sample case shows that the three models have the same expected values, however, the autoregressive model cut by one-lagged period explores different shapes of variance, skewed and kurtosis coefficients from the other two models. This implies that the large samples lead to the same expected values, 2(1 – ρ0, whatever the variance-covariance matrix of the errors is assumed. Finally, comparing with the two sample cases, the shape of each coefficient is almost the same, moreover, the autocorrelation coefficients are negatively related with expected values, are inverted-U related with variances, are cubic related with skewed coefficients, and are U related with kurtosis coefficients.

Behavior of plutonium interacting with bentonite and sulfate-reducing anaerobic bacteria

International Nuclear Information System (INIS)

Kudo, A.; Zheng, J.; Cayer, I.; Fujikawa, Y.; Yoshikawa, H.; Ito, M.

1997-01-01

The interactions between sulfate reducing anaerobic bacteria and plutonium, with or without bentonite present, were investigated using distribution coefficients [Kd (ml/g)] as an index of the radionuclide behavior. Plutonium Kds for living bacteria varied within a large range, from 1,804 to 112,952, depending on the pH, while the Kds ranged from 1,180 to 5,931 for dead bacteria. In general, living bacteria had higher plutonium Kds than dead bacteria. Furthermore, the higher Kd values of 39,677 to 106,915 for living bacteria were obtained for a pH range between 6.83 and 8.25, while no visible pH effect was observed for dead bacteria. These Kd values were obtained using tracers for both 236 Pu and 239 Pu, which can check the experimental procedures and mass balance. Another comparison was conducted for plutonium Kd values of mixtures of living bacteria with bentonite and sterilized bacteria with bentonite. The range of Kd values for the non-sterilized bacteria with bentonite were 1,194 to 83,648 while Kd values for the sterilized bacteria with bentonite were from 624 to 17,236. Again, the Kd values for the living bacteria with bentonite were higher than those of sterilized bacteria with bentonite. In other words, the presence of living anaerobic bacteria with bentonite increased, by roughly 50 times, the Kd values of 239 Pu when compared to the mixture of dead bacteria with bentonite. The results indicate that the effects of anaerobic bacteria within the engineered barrier system (in this case bentonite) will play a significant role in the behavior of plutonium in geologic repositories

Correlation functions for the distribution coefficients of U(IV) and Pu(III) ions between aqueous nitric acid and 30% TBP in an aliphatic diluent

International Nuclear Information System (INIS)

Geldard, J.F.; Beyerlein, A.L.; Phillips, L.

1985-01-01

Distribution coefficient correlations for U(IV) and Pu(III) are obtained in terms of a modified form of the total nitrate ion salting strength that was successfully used to obtain distribution coefficient correlations for U(VI) and Pu(IV) in the earlier work of G.L. Richardson. The modification of salting strength was needed to account for the fact that the U(IV) distribution coefficients measured under conditions where U(VI) is present consistently fall below those obtained when it is absent. The correlations were incorporated into the mixer-settler computer model PUBG, and in the simulation of a 20-stage 1B partitioning contactor, calculated product stream concentrations were in excellent agreement with experiment. Earlier mixer-settler computer models, which failed to account for U(IV) distribution coefficients, predicted that U(IV) remained in the aqueous product stream, which is contrary to the experimental measurements

Correlation functions for the distribution coefficients of U(IV) and Pu(III) ions between aqueous nitric acid and 30% TBP in an aliphatic diluent

Energy Technology Data Exchange (ETDEWEB)

Geldard, J.F.; Beyerlein, A.L.; Phillips, L.

1985-09-01

Distribution coefficient correlations for U(IV) and Pu(III) are obtained in terms of a modified form of the total nitrate ion salting strength that was successfully used to obtain distribution coefficient correlations for U(VI) and Pu(IV) in the earlier work of G.L. Richardson. The modification of salting strength was needed to account for the fact that the U(IV) distribution coefficients measured under conditions where U(VI) is present consistently fall below those obtained when it is absent. The correlations were incorporated into the mixer-settler computer model PUBG, and in the simulation of a 20-stage 1B partitioning contactor, calculated product stream concentrations were in excellent agreement with experiment. Earlier mixer-settler computer models, which failed to account for U(IV) distribution coefficients, predicted that U(IV) remained in the aqueous product stream, which is contrary to the experimental measurements.

Monitoring device for local power peaking coefficients

International Nuclear Information System (INIS)

Mihashi, Ishi

1987-01-01

Purpose: To determine and monitor the local power peaking coefficients by a method not depending on the combination of fuel types. Constitution: Representative values for the local power distribution can be obtained by determining corresponding burn-up degrees based on the burn-up degree of each of fuel assembly segments obtained in a power distribution monitor and by the interpolation and extrapolation of void coefficients. The typical values are multiplied with compensation coefficients for the control rod effect and coefficients for compensating the effect of adjacent fuel assemblies in a calculation device to obtain typical values for the present local power distribution compensated with all of the effects. Further, the calculation device compares them with typical values of the present local power distribution to obtain an aimed local power peaking coefficient as the maximum value thereof. According to the present invention, since the local power peaking coefficients can be determined not depending on the combination of the kind of fuels, if the combination of fuel assemblies is increased upon fuel change, the amount of operation therefor is not increased. (Kamimura, M.)

Carrier Mediated Distribution System (CAMDIS): a new approach for the measurement of octanol/water distribution coefficients.

Science.gov (United States)

Wagner, Bjoern; Fischer, Holger; Kansy, Manfred; Seelig, Anna; Assmus, Frauke

2015-02-20

Here we present a miniaturized assay, referred to as Carrier-Mediated Distribution System (CAMDIS) for fast and reliable measurement of octanol/water distribution coefficients, log D(oct). By introducing a filter support for octanol, phase separation from water is facilitated and the tendency of emulsion formation (emulsification) at the interface is reduced. A guideline for the best practice of CAMDIS is given, describing a strategy to manage drug adsorption at the filter-supported octanol/buffer interface. We validated the assay on a set of 52 structurally diverse drugs with known shake flask log D(oct) values. Excellent agreement with literature data (r(2) = 0.996, standard error of estimate, SEE = 0.111), high reproducibility (standard deviation, SD < 0.1 log D(oct) units), minimal sample consumption (10 μL of 100 μM DMSO stock solution) and a broad analytical range (log D(oct) range = -0.5 to 4.2) make CAMDIS a valuable tool for the high-throughput assessment of log D(oc)t. Copyright © 2014 Elsevier B.V. All rights reserved.

Vertical random variability of the distribution coefficient in the soil and its effect on the migration of fallout radionuclides

International Nuclear Information System (INIS)

Bunzl, K.

2002-01-01

In the field, the distribution coefficient, K d , for the sorption of a radionuclide by the soil cannot be expected to be constant. Even in a well defined soil horizon, K d will vary stochastically in horizontal as well as in vertical direction around a mean value. The horizontal random variability of K d produce a pronounced tailing effect in the concentration depth profile of a fallout radionuclide, much less is known on the corresponding effect of the vertical random variability. To analyze this effect theoretically, the classical convection-dispersion model in combination with the random-walk particle method was applied. The concentration depth profile of a radionuclide was calculated one year after deposition assuming constant values of the pore water velocity, the diffusion/dispersion coefficient, and the distribution coefficient (K d = 100 cm 3 x g -1 ) and exhibiting a vertical variability for K d according to a log-normal distribution with a geometric mean of 100 cm 3 x g -1 and a coefficient of variation of CV 0.53. The results show that these two concentration depth profiles are only slightly different, the location of the peak is shifted somewhat upwards, and the dispersion of the concentration depth profile is slightly larger. A substantial tailing effect of the concentration depth profile is not perceivable. Especially with respect to the location of the peak, a very good approximation of the concentration depth profile is obtained if the arithmetic mean of the K d -values (K d = 113 cm 3 x g -1 ) and a slightly increased dispersion coefficient are used in the analytical solution of the classical convection-dispersion equation with constant K d . The evaluation of the observed concentration depth profile with the analytical solution of the classical convection-dispersion equation with constant parameters will, within the usual experimental limits, hardly reveal the presence of a log-normal random distribution of K d in the vertical direction in

Effects of aqueous-soluble organic compounds on the removal of selected radionuclides from high-level waste part I: Distribution of Sr, Cs, and Tc onto 18 absorbers from an irradiated, organic-containing leachate simulant for Hanford Tank 101-SY

International Nuclear Information System (INIS)

Marsh, S.F.; Svitra, Z.V.; Bowen, S.M.

1995-01-01

Many of the radioactive waste storage tanks at U.S. Department of Energy facilities contain organic compounds that have been degraded by radiolysis and chemical reactions. In this investigation, we measured the effect of some aqueous-soluble organic compounds on the sorption of strontium, cesium, and technetium onto 18 absorbers that offer high sorption of strontium from organic-free solutions. For our test solution we used a leachate from a simulated slurry for Hanford Tank 101-SY that initially contained ethylenediaminetetraacetic acid (EDTA) and then was gamma-irradiated to 34 Mrads. We measured distribution coefficients (Kds) for each element/absorber combination for dynamic contact periods of 30 min, 2 h, and 6 h to obtain information about sorption kinetics. To facilitate comparisons, we include Kd values for these same element/absorber combinations from three organic-free simulant solutions. The Kd values for strontium sorption from the simulant that contained the degraded organics usually decreased by large factors, whereas the Kd values for cesium and technetium sorption were relatively unaffected

Estimation of the location parameter of distributions with known coefficient of variation by record values

Directory of Open Access Journals (Sweden)

N. K. Sajeevkumar

2014-09-01

Full Text Available In this article, we derived the Best Linear Unbiased Estimator (BLUE of the location parameter of certain distributions with known coefficient of variation by record values. Efficiency comparisons are also made on the proposed estimator with some of the usual estimators. Finally we give a real life data to explain the utility of results developed in this article.

Relation between distribution coefficient of radioactive strontium and solid-liquid distribution ratio of background stable strontium

International Nuclear Information System (INIS)

Igarashi, Toshifumi; Mahara, Yasunori; Okamura, Masaki; Ashikawa, Nobuo.

1992-01-01

Distribution coefficients (K d ) of nuclides, which are defined as the ratio of the adsorbed concentration to the solution concentration, are important in predicting nuclide migration in the subsurface environment. This study was undertaken to contrust an effective method of determining the most pertinent K d value for simulating in situ distribution phenomena between the solid and liquid phases, by using background stable isotopes. This paper describes the applicability of this method to Sr by carrying out a batch Sr adsorption experiment where stable Sr coexisted with the radioactive isotope, 85 Sr, and by comparing the concentration distribution ratio of the background stable Sr with the K d value obtained by the batch experiment. The results showed that the K d of 85 Sr (K d85 ) agreed well with the K d of the coexisting stable Sr (K ds ) and that the two values decreased with an increase in the concentration of the stable Sr, when sand was used as an adsorbent. In addition, the K d85 corresponded to the ratio of the exchangeable solid-phase concentration of background stable Sr to the concentration of the background stable Sr in groundwater when the concentration of the coexisting stable Sr approached the background level. On the other hand, when powdered rock samples were used, the K d85 did not agree with the K ds , and the concentration distribution ratio of the background stable Sr was greater than the K d85 . This discrepancy might be due to the disequilibrium resulting from grinding the rock matrices. This suggests that measurement of the background stable Sr distribution ratio between the solid and liquid phases can be an effective method of estimating the K d of radioactive Sr when the groundwater is in satisfactory contact with the adsorption medium. (author)

A Numerical Procedure for Flow Distribution and Pressure Drops for U and Z Type Configurations Plate Heat Exchangers with Variable Coefficients

International Nuclear Information System (INIS)

López, R; Lecuona, A; Ventas, R; Vereda, C

2012-01-01

In Plate Heat Exchangers it is important to determine the flow distribution and pressure drops, because they affect directly the performance of a heat exchanger. This work proposes an incompressible, one-dimensional, steady state, discrete model allowing for variable overall momentum coefficients to determine these magnitudes. The model consists on a modified version of the Bajura and Jones model for dividing and combining flow manifolds. The numerical procedure is based on the finite differences approximation approach proposed by Datta and Majumdar. A linear overall momentum coefficient distribution is used in the dividing manifold, but the model is not limited to linear distributions. Comparisons are made with experimental, numerical and analytical data, yielding good results.

STUDY OF REFLECTION COEFFICIENT DISTRIBUTION FOR ANTI-REFLECTION COATINGS ON SMALL-RADIUS OPTICAL PARTS

Directory of Open Access Journals (Sweden)

L. A. Gubanova

2015-03-01

Full Text Available The paper deals with findings for the energy reflection coefficient distribution of anti- reflection coating along the surface of optical elements with a very small radius (2-12 mm. The factors influencing the magnitude of the surface area of the optical element, in which the energy reflection coefficient is constant, were detected. The main principles for theoretical models that describe the spectral characteristics of the multilayer interference coatings were used to achieve these objectives. The relative size of the enlightenment area is defined as the ratio of the radius for the optical element surface, where the reflection is less than a certain value, to its radius (ρ/r. The result of research is the following: this size is constant for a different value of the curvature radius for the optical element made of the same material. Its value is determined by the refractive index of material (nm, from which the optical element was made, and the design of antireflection coatings. For single-layer coatings this value is ρ/r = 0.5 when nm = 1.51; and ρ/r = 0.73 when nm = 1.75; for two-layer coatings ρ/r = 0.35 when nm = 1.51 and ρ/r = 0.41 when nm = 1.75. It is shown that with increasing of the material refractive index for the substrate size, the area of minimum reflection coefficient is increased. The paper considers a single-layer, two-layer, three-layer and five-layer structures of antireflection coatings. The findings give the possibility to conclude that equal thickness coverings formed on the optical element surface with a small radius make no equal reflection from the entire surface, and distribution of the layer thickness needs to be looked for, providing a uniform radiation reflection at all points of the spherical surface.

Spectro-ellipsometric studies of sputtered amorphous Titanium dioxide thin films: simultaneous determination of refractive index, extinction coefficient, and void distribution

CERN Document Server

Lee, S I; Oh, S G

1999-01-01

Amorphous titanium dioxide thin films were deposited onto silicon substrates by using RF magnetron sputtering, and the index of refraction, the extinction coefficient, and the void distribution of these films were simultaneously determined from the analyses of there ellipsometric spectra. In particular, our novel strategy, which combines the merits of multi-sample fitting, the dual dispersion function, and grid search, was proven successful in determining optical constants over a wide energy range, including the energy region where the extinction coefficient was large. Moreover, we found that the void distribution was dependent on the deposition conditions, such as the sputtering power, the substrate temperature, and the substrate surface.

Classification of distribution coefficient data by mineral components and chemical forms

International Nuclear Information System (INIS)

Takeda, Seiji; Kimura, Hideo; Matsuzuru, Hideo

1996-01-01

The use of distribution coefficient (Kd) in radionuclide transport model has been reported in a number of papers. However, Kd data cover a wide range even for a specific element. In this study the Kd data of neptunium, uranium and selenium, which are included in sorption database (SDB, OECD/NEA) of radionuclides, were classified by a solid phase and a dominant species in a solution. The aqueous species of these elements were estimated by a geochemical model. The Kd data classified by the analyzed speciation were tested by a nonparametric statistical method. The results of tests proved that the Kd data of neptunium or uranium, which covered a wide range, were influenced by the supersaturation of Np(OH) 4 (s) or schoepite. The Kd data of neptunium could be classified by the dominant aqueous species, NpO 2 + , NpO 2 CO 3 - , NpO 2 OH(aq) and Np(OH) 4 (aq). The Kd data of these four dominant species which are not equilibrated with supersaturated Np(OH) 4 (s) are less than 100 ml/g. The analyzed aqueous species of uranium were UO 2 (OH) 2 (aq) and UO 2 (CO 3 ) n 2-2n (n=2,3) in hexavalent state. It is suggested that the distribution coefficient of neptunium and uranium depends on dominant aqueous species or charged species, i.e., cationic, anionic and nonionic forms. The dominant aqueous species of selenium are HSe - , HSeO 3 - , SeO 3 2- and SeO 4 2- . The result of the nonparametric statistical test shows that the Kd value of HSeO 3 - is higher than of other anionic forms. However, the influence of the species, HSe - , SeO 3 2- and SeO 4 2- , on Kd values is not clearly identified. Considering the dominant species, the Kd of elements are in ranges of 1 to 2 orders of magnitude being in general narrower than those classified by mineral and rock types. (author)

Experimental determination of the distribution coefficient (Kd) of lead and barium in soils of semiarid region of Bahia, Brazil

International Nuclear Information System (INIS)

Santos, Mariana M.; Fernandes, Heloisa H.F; Pontedeiro, Elizabeth M.; Su, Jian

2013-01-01

To determine the concentration of heavy metals and other contaminants in soils, aimed at evaluating the environmental impact, the use of the distribution coefficient is required (Kd), defined as the relationship between the concentrations adsorbed and in solution. The objective of this study was to determine the rates for the Lead and Barium metals in soil collected in Caetite, the state of Bahia, in two different depths. The importance of determining the distribution coefficient lies in the fact that being performed using a tropical soil. For the isotherms of Kd was used batch test method by adsorption to obtain the final concentrations. The first step was to determine the best ratio soil: solution obtained after equilibration time and finally the equilibrium concentration of the contaminant. Were also calculated percentages of the metal adsorbed by the soil and the amount of solute by the adsorbent. With the values obtained in experiments and using Mathematica 8.0 software, were made graphics equilibrium concentration versus quantity adsorbed (C vs. S). It can also plot isotherms for different models of Kd: linear, Langmuir and Freundlich in order to determine which adsorption model would fit best to the measured data and thus determine the distribution coefficient of the metal in the soil analyzed. The Freundlich isotherm was better adapted to the points of the two metals in both soils

Determination of the distribution coefficients for the radionuclides 134Cs, 60Co and 234Th in the Pinheiros river sediment

International Nuclear Information System (INIS)

Lima, Marina Ferreira

1992-01-01

The distribution coefficients (Kd) were determined in order to foresee the fate of the radionuclides discharged to the environment. Based upon the source-term released by IPEN's facilities in Pinheiros River during the year of 1988, three radionuclides were chosen as being the more critical, according to the radiation protection standards: 137 Cs, 60 Co and 232 Th. Their Kd were determined experimentally in laboratory by using the corresponding radioactive tracers 134 Cs, 60 Co and 234 Th. Three different experimental methodologies were used: the static method. the shaken method and the dynamic method. The parameters studied were the effects of pH, aerobic condition and time of contact. No considerable changes were observed for the cesium Kd with the variation of pH and aerobic condition, the kd extreme values being 20 ml/g and 30 ml/g for the pH range between 4 and 8. The study of the time of contact showed that the equilibrium between the cesium concentration in the water and sediment was achieved in a few days. For the cobalt, the pH effect was considerable, since the Kd increased from 46 ml/g for pH 4 to 2,25x10 3 ml/g for pH 8. The Kd observed with the agitation with air was around 420 ml/g, rising to 670 ml/g with the agitation with N 2 . The results obtained in the study of the time of contact effect showed that the equilibrium between the cobalt concentration in the water and sediment was not achieved even after 15 days of contact. For the thorium, also, the pH effect was considerable, since the Kd increased fram 1,40 x 10 5 ml/g for pH 4 to 2,55 x 10 6 ml/g for pH 8. No effect was observed, on the other hand, for the kd values obtained in the experiment carried out with air agitation or N 2 agitation, around 2,75 x 10 6 ml/g. The results obtained in the study of the time of contact effect showed that the equilibrium between the thorium concentration in the water and sediment was achieved after just one hour of contact. The results obtained can be

Estimation of distribution coefficient for uranium in soil around a waste disposal site at Trombay

International Nuclear Information System (INIS)

Mishra, S.; Chaudhary, D.K.; Sandeep, P.; Pandit, G.G.

2014-01-01

Soil contamination arising from the disposed waste from industrial origin is of major concern now a days. There is a possibility of run off as well as Ieaching of contaminants from the sites to nearby aquatic bodies through rain water. Distribution coefficient, K d in soil is an important parameter to predict the migration of contaminants. However it requires precise measurement not only for the accurate prediction of contaminant transport but also for describing the sorption behavior in a particular environment. The variation of K d values for a radionuclide is due to differences in geochemical conditions, soil materials, nature of water and methods used for the measurements. For the present study soil samples have been collected near a waste disposal site at Trombay and the sorption of uranium has been studied by measuring the distribution coefficient (K d ) by laboratory batch method. In our earlier studies, we could notice substantial effect of ionic composition of ground water on the K d values of uranium. In this study we have used rain water as the sorption media and the measured K d value s were compared with previous values for different soil and water characteristics from different regions of India

Coefficient Omega Bootstrap Confidence Intervals: Nonnormal Distributions

Science.gov (United States)

Padilla, Miguel A.; Divers, Jasmin

2013-01-01

The performance of the normal theory bootstrap (NTB), the percentile bootstrap (PB), and the bias-corrected and accelerated (BCa) bootstrap confidence intervals (CIs) for coefficient omega was assessed through a Monte Carlo simulation under conditions not previously investigated. Of particular interests were nonnormal Likert-type and binary items.…

A microfluidic platform for the rapid determination of distribution coefficients by gravity assisted droplet-based liquid-liquid extraction

DEFF Research Database (Denmark)

Poulsen, Carl Esben; Wootton, Robert C. R.; Wolff, Anders

2015-01-01

The determination of pharmacokinetic properties of drugs, such as the distribution coefficient, D, is a crucial measurement in pharmaceutical research. Surprisingly, the conventional (gold standard) technique used for D measurements, the shake-flask method, is antiquated and unsuitable...... for the testing of valuable and scarce drug candidates. Herein we present a simple micro fluidic platform for the determination of distribution coefficients using droplet-based liquid-liquid extraction. For simplicity, this platform makes use of gravity to enable phase separation for analysis and is 48 times...... the apparent acid dissociation constant, pK', as a proxy for inter-system comparison. Our platform determines a pK' value of 7.24 ± 0.15, compared to 7.25 ± 0.58 for the shake-flask method in our hands and 7.21 for the shake-flask method in literature. Devices are fabricated using injection moulding, the batch...

Evaluation of distribution coefficients for the prediction of strontium and cesium migration in a uniform sand

International Nuclear Information System (INIS)

Reynolds, W.D.; Gillham, R.W.; Cherry, J.A.

1982-01-01

The validity of using a distribution coefficient (Ksub(d)) in the mathematical prediction of strontium and cesium transport through uniform saturated sand was investigated by comparing measured breakthrough curves with curves of simulations using the advection-dispersion and the advection equations. Values for Ksub(d) were determined by batch equilibration tests and, indirectly, by fitting the mathematical model to breakthrough data from column experiments. Although the advection-dispersion equation accurately represented the breakthrough curves for two nonreactive solutes (chloride and tritium), neither it nor the advection equation provided close representations of the strontium and cesium curves. The simulated breakthrough curves for strontium and cesium were nearly symmetrical, whereas the data curves were very asymmetrical, with long tails. Column experiments with different pore-water velocities indicated that the shape of the normalized breakthrough curves was not sensitive to velocity. This suggests that the asymmetry of the measured curves was the result of nonlinear partitioning of the cations between the solid and liquid phases, rather than nonequilibrium effects. The results indicate that the distribution coefficient, when used in advection-dispersion models for prediction of the migration of strontium and cesium in field situations, can result in significant error

Meta-Analysis of Coefficient Alpha

Science.gov (United States)

Rodriguez, Michael C.; Maeda, Yukiko

2006-01-01

The meta-analysis of coefficient alpha across many studies is becoming more common in psychology by a methodology labeled reliability generalization. Existing reliability generalization studies have not used the sampling distribution of coefficient alpha for precision weighting and other common meta-analytic procedures. A framework is provided for…

Field experiment determinations of distribution coefficients of actinide elements in alkaline lake environments

International Nuclear Information System (INIS)

Simpson, H.J.; Trier, R.M.; Li, Y.H.; Anderson, R.F.

1984-01-01

Radionuclide concentrations of a number of elements (Am, Pu, U, Pa, Th, Ac, Ra, Po, Pb, Cs, and Sr) have been measured in the water and sediments of a group of alkaline lakes in the western USA. These data demonstrate greatly enhanced soluble phase concentrations of elements with oxidation states of III, IV, V, and VI as the result of carbonate complexing. Dissolved concentrations of isotopes of U, Pa, and Th in a lake with pH = 10 and a total inorganic carbon concentration of 4 x 10 -1 moles/1 were greater than those in sea water (pH = 8, ΣCO 2 = 2 x 10 -3 moles/1) by order of magnitude for 233 U, 238 U (--10 2 ), 231 Pa, 228 Th, 230 Th (--10 3 ) and 22 Th (--10 5 ). Concentrations of fallout /sup 239,240/Pu in the more alkaline lakes were equivalent to effective distribution coefficients of --10 3 , about a factor of 10 2 lower than in most other natural lakes, rivers, estuaries and coastal marine waters. Measurements of radionuclides in natural systems are essential for assessment of the likely fate of radionuclides which may be released from high level waste repositories to ground water. Laboratory-scale experiments using tracer additions of radionuclides to mixtures of water and sediment yielded distribution coefficients which were significantly different from those derived from field measurements (10 1 -10 2 lower for Po and Pu). Order of magnitude calculations from thermodynamic data of expected maximum U and Th concentrations, limited by pure phase solubilities, suggest that carbonate complexing can enhance solubility by many orders of magnitude in natural waters, even at relatively low carbonate ion concentrations

Calculation of age-dependent dose conversion coefficients for radionuclides uniformly distributed in air

International Nuclear Information System (INIS)

Hung, Tran Van; Satoh, Daiki; Takahashi, Fumiaki; Tsuda, Shuichi; Endo, Akira; Saito, Kimiaki; Yamaguchi, Yasuhiro

2005-02-01

Age-dependent dose conversion coefficients for external exposure to photons emitted by radionuclides uniformly distributed in air were calculated. The size of the source region in the calculation was assumed to be effectively semi-infinite in extent. Firstly, organ doses were calculated with a series of age-specific MIRD-5 type phantoms using MCNP code, a Monte Carlo transport code. The calculations were performed for mono-energetic photon sources of twelve energies from 10 keV to 5 MeV and for phantoms of newborn, 1, 5, 10 and 15 years, and adult. Then, the effective doses to the different age-phantoms from the mono-energetic photon sources were estimated based on the obtained organ doses. The calculated effective doses were used to interpolate the conversion coefficients of the effective doses for 160 radionuclides, which are important for dose assessment of nuclear facilities. In the calculation, energies and intensities of emitted photons from radionuclides were taken from DECDC, a recent compilation of decay data for radiation dosimetry developed at JAERI. The results are tabulated in the form of effective dose per unit concentration and time (Sv per Bq s m -3 ). (author)

Activity coefficients of electrons and holes in semiconductors

International Nuclear Information System (INIS)

Orazem, M.E.; Newman, J.

1984-01-01

Dilute-solution transport equations with constant activity coefficients are commonly used to model semiconductors. These equations are consistent with a Boltzmann distribution and are invalid in regions where the species concentration is close to the respective site concentration. A more rigorous treatment of transport in a semiconductor requires activity coefficients which are functions of concentration. Expressions are presented for activity coefficients of electrons and holes in semiconductors for which conduction- and valence-band energy levels are given by the respective bandedge energy levels. These activity coefficients are functions of concentration and are thermodynamically consistent. The use of activity coefficients in macroscopic transport relationships allows a description of electron transport in a manner consistent with the Fermi-Dirac distribution

A parameterization scheme for the x-ray linear attenuation coefficient and energy absorption coefficient.

Science.gov (United States)

Midgley, S M

2004-01-21

A novel parameterization of x-ray interaction cross-sections is developed, and employed to describe the x-ray linear attenuation coefficient and mass energy absorption coefficient for both elements and mixtures. The new parameterization scheme addresses the Z-dependence of elemental cross-sections (per electron) using a simple function of atomic number, Z. This obviates the need for a complicated mathematical formalism. Energy dependent coefficients describe the Z-direction curvature of the cross-sections. The composition dependent quantities are the electron density and statistical moments describing the elemental distribution. We show that it is possible to describe elemental cross-sections for the entire periodic table and at energies above the K-edge (from 6 keV to 125 MeV), with an accuracy of better than 2% using a parameterization containing not more than five coefficients. For the biologically important elements 1 coefficients. At higher energies, the parameterization uses fewer coefficients with only two coefficients needed at megavoltage energies.

Predicting volume of distribution with decision tree-based regression methods using predicted tissue:plasma partition coefficients.

Science.gov (United States)

Freitas, Alex A; Limbu, Kriti; Ghafourian, Taravat

2015-01-01

Volume of distribution is an important pharmacokinetic property that indicates the extent of a drug's distribution in the body tissues. This paper addresses the problem of how to estimate the apparent volume of distribution at steady state (Vss) of chemical compounds in the human body using decision tree-based regression methods from the area of data mining (or machine learning). Hence, the pros and cons of several different types of decision tree-based regression methods have been discussed. The regression methods predict Vss using, as predictive features, both the compounds' molecular descriptors and the compounds' tissue:plasma partition coefficients (Kt:p) - often used in physiologically-based pharmacokinetics. Therefore, this work has assessed whether the data mining-based prediction of Vss can be made more accurate by using as input not only the compounds' molecular descriptors but also (a subset of) their predicted Kt:p values. Comparison of the models that used only molecular descriptors, in particular, the Bagging decision tree (mean fold error of 2.33), with those employing predicted Kt:p values in addition to the molecular descriptors, such as the Bagging decision tree using adipose Kt:p (mean fold error of 2.29), indicated that the use of predicted Kt:p values as descriptors may be beneficial for accurate prediction of Vss using decision trees if prior feature selection is applied. Decision tree based models presented in this work have an accuracy that is reasonable and similar to the accuracy of reported Vss inter-species extrapolations in the literature. The estimation of Vss for new compounds in drug discovery will benefit from methods that are able to integrate large and varied sources of data and flexible non-linear data mining methods such as decision trees, which can produce interpretable models. Graphical AbstractDecision trees for the prediction of tissue partition coefficient and volume of distribution of drugs.

Calculation of the fuel temperature coefficient of reactivity considering non-uniform radial temperature distribution in the fuel rod

Energy Technology Data Exchange (ETDEWEB)

Pazirandeh, Ali [Islamic Azad Univ., Tehran (Iran, Islamic Republic of). Science and Research Branch; Hooshyar Mobaraki, Almas

2017-07-15

The safe operation of a reactor is based on feedback models. In this paper we attempted to discuss the influence of a non-uniform radial temperature distribution on the fuel rod temperature coefficient of reactivity. The paper demonstrates that the neutron properties of a reactor core is based on effective temperature of the fuel to obtain the correct fuel temperature feedback. The value of volume-averaged temperature being used in the calculations of neutron physics with feedbacks would result in underestimating the probable event. In the calculation it is necessary to use the effective temperature of the fuel in order to provide correct accounting of the fuel temperature feedback. Fuel temperature changes in different zones of the core and consequently reactivity coefficient change are an important parameter for analysis of transient conditions. The restricting factor that compensates the inserted reactivity is the temperature reactivity coefficient and effective delayed neutron fraction.

Limits of the memory coefficient in measuring correlated bursts

Science.gov (United States)

Jo, Hang-Hyun; Hiraoka, Takayuki

2018-03-01

Temporal inhomogeneities in event sequences of natural and social phenomena have been characterized in terms of interevent times and correlations between interevent times. The inhomogeneities of interevent times have been extensively studied, while the correlations between interevent times, often called correlated bursts, are far from being fully understood. For measuring the correlated bursts, two relevant approaches were suggested, i.e., memory coefficient and burst size distribution. Here a burst size denotes the number of events in a bursty train detected for a given time window. Empirical analyses have revealed that the larger memory coefficient tends to be associated with the heavier tail of the burst size distribution. In particular, empirical findings in human activities appear inconsistent, such that the memory coefficient is close to 0, while burst size distributions follow a power law. In order to comprehend these observations, by assuming the conditional independence between consecutive interevent times, we derive the analytical form of the memory coefficient as a function of parameters describing interevent time and burst size distributions. Our analytical result can explain the general tendency of the larger memory coefficient being associated with the heavier tail of burst size distribution. We also find that the apparently inconsistent observations in human activities are compatible with each other, indicating that the memory coefficient has limits to measure the correlated bursts.

Chaotic oscillations of the Klein-Gordon equation with distributed energy pumping and van der Pol boundary regulation and distributed time-varying coefficients

Directory of Open Access Journals (Sweden)

Bo Sun

2014-09-01

Full Text Available Consider the Klein-Gordon equation with variable coefficients, a van der Pol cubic nonlinearity in one of the boundary conditions and a spatially distributed antidamping term, we use a variable-substitution technique together with the analogy with the 1-dimensional wave equation to prove that for the Klein-Gordon equation chaos occurs for a class of equations and boundary conditions when system parameters enter a certain regime. Chaotic and nonchaotic profiles of solutions are illustrated by computer graphics.

Monitoring device for local power peaking coefficient

International Nuclear Information System (INIS)

Mitsuhashi, Ishi

1987-01-01

Purpose: To monitor the local power peaking coefficients obtained by the method not depending on the combination of fuel types. Method: A plurality of representative values for the local power distribution determined by the nuclear constant calculation for one fuel assembly are memorized regarding each of the burn-up degree and the void coefficient on every positions and fuel types in fuel rod assemblies. While on the other hand, the representative values for the local power distribution as described above are compensated by a compensation coefficient considering the effect of adjacent segments and a control rod compensation coefficient considering the effect due to the control rod insertion relative to the just-mentioned compensation coefficient. Then, the maximum value among them is selected to determine the local power peaking coefficient at each of the times and each of the segments, which is monitored. According to this system, the calculation and the working required for the fitting work depending on the combination of fuel types are no more required at all to facilitate the maintenance as well. (Horiuchi, T.)

Variable-coefficient higher-order nonlinear Schroedinger model in optical fibers: Variable-coefficient bilinear form, Baecklund transformation, brightons and symbolic computation

International Nuclear Information System (INIS)

Tian Bo; Gao Yitian; Zhu Hongwu

2007-01-01

Symbolically investigated in this Letter is a variable-coefficient higher-order nonlinear Schroedinger (vcHNLS) model for ultrafast signal-routing, fiber laser systems and optical communication systems with distributed dispersion and nonlinearity management. Of physical and optical interests, with bilinear method extend, the vcHNLS model is transformed into a variable-coefficient bilinear form, and then an auto-Baecklund transformation is constructed. Constraints on coefficient functions are analyzed. Potentially observable with future optical-fiber experiments, variable-coefficient brightons are illustrated. Relevant properties and features are discussed as well. Baecklund transformation and other results of this Letter will be of certain value to the studies on inhomogeneous fiber media, core of dispersion-managed brightons, fiber amplifiers, laser systems and optical communication links with distributed dispersion and nonlinearity management

Sorption distribution coefficients of uranium, thorium and radium of selected Malaysian peat soils

International Nuclear Information System (INIS)

Mohd Zaidi Ibrahim; Zalina Laili; Muhamat Omar; Phillip, Esther

2010-01-01

A study on sorption of uranium, thorium and radium on Malaysian peat soils was conducted to determine their distribution coefficient (K d ) values. Batch studies were performed to investigate the influence of pH and the concentrations of radionuclides. Peat soil samples used in this study were collected from Bachok, Batu Pahat, Dalat, Hutan Melintang and Pekan. The peat samples from different location have different chemical characteristics and K d values. No correlation was found between chemical characteristics and the K d values for radium and thorium, but K d value for uranium was found correlated with humic and organic content. The K d value was found to be influenced by soluble humic substances or humic substances leach out from peat soils. (author)

Evaluating and categorizing the reliability of distribution coefficient values in the sorption database

International Nuclear Information System (INIS)

Ochs, Michael; Saito, Yoshihiko; Kitamura, Akira; Shibata, Masahiro; Sasamoto, Hiroshi; Yui, Mikazu

2007-03-01

Japan Atomic Energy Agency (JAEA) has developed the sorption database (JNC-SDB) for bentonite and rocks in order to assess the retardation property of important radioactive elements in natural and engineered barriers in the H12 report. The database includes distribution coefficient (K d ) of important radionuclides. The K d values in the SDB are about 20,000 data. The SDB includes a great variety of K d and additional key information from many different literatures. Accordingly, the classification guideline and classification system were developed in order to evaluate the reliability of each K d value (Th, Pa, U, Np, Pu, Am, Cm, Cs, Ra, Se, Tc on bentonite). The reliability of 3740 K d values are evaluated and categorized. (author)

Sorption of Pu onto some kinds of clay

International Nuclear Information System (INIS)

Jia Haihong; Si Gaohua; Liu Wei; Yu Jing

2010-01-01

There are rich clay mines holding in one area, so it's necessary to know about these clays' sorption capacity to Pu, for building radioactive waste repository in the area. Distribution coefficients of Pu onto different clays were acquired in static method, with the result about 104. The size of clay is different, but the result of Kds is near. In addition, it's estimated how far Pu moves in the most rapid speed in the clay based on these Kids', disregarding the influence of Pu-colloid. In a word, as a kind of backfilling material clays in the area can effectively prevent Pu from moving to environment, and when designing the backfilling layer, it's not necessary to catch clays through NO.200 sieve, if only considering the influence of Kd. (authors)

Using the Gini Coefficient for Bug Prediction in Eclipse

NARCIS (Netherlands)

Giger, E.; Pinzger, M.; Gall, H.C.

2011-01-01

The Gini coefficient is a prominent measure to quantify the inequality of a distribution. It is often used in the field of economy to describe how goods, e.g., wealth or farmland, are distributed among people. We use the Gini coefficient to measure code ownership by investigating how changes made to

Random matrix theory analysis of cross-correlations in the US stock market: Evidence from Pearson’s correlation coefficient and detrended cross-correlation coefficient

Science.gov (United States)

Wang, Gang-Jin; Xie, Chi; Chen, Shou; Yang, Jiao-Jiao; Yang, Ming-Yan

2013-09-01

In this study, we first build two empirical cross-correlation matrices in the US stock market by two different methods, namely the Pearson’s correlation coefficient and the detrended cross-correlation coefficient (DCCA coefficient). Then, combining the two matrices with the method of random matrix theory (RMT), we mainly investigate the statistical properties of cross-correlations in the US stock market. We choose the daily closing prices of 462 constituent stocks of S&P 500 index as the research objects and select the sample data from January 3, 2005 to August 31, 2012. In the empirical analysis, we examine the statistical properties of cross-correlation coefficients, the distribution of eigenvalues, the distribution of eigenvector components, and the inverse participation ratio. From the two methods, we find some new results of the cross-correlations in the US stock market in our study, which are different from the conclusions reached by previous studies. The empirical cross-correlation matrices constructed by the DCCA coefficient show several interesting properties at different time scales in the US stock market, which are useful to the risk management and optimal portfolio selection, especially to the diversity of the asset portfolio. It will be an interesting and meaningful work to find the theoretical eigenvalue distribution of a completely random matrix R for the DCCA coefficient because it does not obey the Marčenko-Pastur distribution.

Resummed coefficient function for the shape function

OpenAIRE

Aglietti, U.

2001-01-01

We present a leading evaluation of the resummed coefficient function for the shape function. It is also shown that the coefficient function is short-distance-dominated. Our results allow relating the shape function computed on the lattice to the physical QCD distributions.

Correlation Coefficients: Appropriate Use and Interpretation.

Science.gov (United States)

Schober, Patrick; Boer, Christa; Schwarte, Lothar A

2018-05-01

Correlation in the broadest sense is a measure of an association between variables. In correlated data, the change in the magnitude of 1 variable is associated with a change in the magnitude of another variable, either in the same (positive correlation) or in the opposite (negative correlation) direction. Most often, the term correlation is used in the context of a linear relationship between 2 continuous variables and expressed as Pearson product-moment correlation. The Pearson correlation coefficient is typically used for jointly normally distributed data (data that follow a bivariate normal distribution). For nonnormally distributed continuous data, for ordinal data, or for data with relevant outliers, a Spearman rank correlation can be used as a measure of a monotonic association. Both correlation coefficients are scaled such that they range from -1 to +1, where 0 indicates that there is no linear or monotonic association, and the relationship gets stronger and ultimately approaches a straight line (Pearson correlation) or a constantly increasing or decreasing curve (Spearman correlation) as the coefficient approaches an absolute value of 1. Hypothesis tests and confidence intervals can be used to address the statistical significance of the results and to estimate the strength of the relationship in the population from which the data were sampled. The aim of this tutorial is to guide researchers and clinicians in the appropriate use and interpretation of correlation coefficients.

Study of the mineralogic composition influence of the ground of Goiania, Brazil, in the distribution coefficient of the 137 Cs

International Nuclear Information System (INIS)

Anon

2000-01-01

Interactions between the soil and a solute in a liquid effluent depend on the characteristics of this solute as well as on the nature of the soil. The soil distribution coefficient K d in non altered natural systems can be estimated by the summation of the K d 's of its individual mineral components. In thesis this approach allows an evaluation of the distribution coefficient on the basis of the qualitative and quantitative identification of the mineral constituents of a given soil. This work reported here aimed at gathering preliminary data and at pointing the relevance of the approach in studies of radionuclide sorption by soils. A sample of the Goiania soil was collected and analyzed by X Ray diffractometry. The thus identified mineral components were subsequently submitted to individual batch tests, using 137 Cs as tracer. The mineral species tested were: kaolinite, gibbsite, goethite, hematite, muscovite, quartz and zirconite. The values obtained for K d are presented and discussed. (author)

Performance of intraclass correlation coefficient (ICC) as a reliability index under various distributions in scale reliability studies.

Science.gov (United States)

Mehta, Shraddha; Bastero-Caballero, Rowena F; Sun, Yijun; Zhu, Ray; Murphy, Diane K; Hardas, Bhushan; Koch, Gary

2018-04-29

Many published scale validation studies determine inter-rater reliability using the intra-class correlation coefficient (ICC). However, the use of this statistic must consider its advantages, limitations, and applicability. This paper evaluates how interaction of subject distribution, sample size, and levels of rater disagreement affects ICC and provides an approach for obtaining relevant ICC estimates under suboptimal conditions. Simulation results suggest that for a fixed number of subjects, ICC from the convex distribution is smaller than ICC for the uniform distribution, which in turn is smaller than ICC for the concave distribution. The variance component estimates also show that the dissimilarity of ICC among distributions is attributed to the study design (ie, distribution of subjects) component of subject variability and not the scale quality component of rater error variability. The dependency of ICC on the distribution of subjects makes it difficult to compare results across reliability studies. Hence, it is proposed that reliability studies should be designed using a uniform distribution of subjects because of the standardization it provides for representing objective disagreement. In the absence of uniform distribution, a sampling method is proposed to reduce the non-uniformity. In addition, as expected, high levels of disagreement result in low ICC, and when the type of distribution is fixed, any increase in the number of subjects beyond a moderately large specification such as n = 80 does not have a major impact on ICC. Copyright © 2018 John Wiley & Sons, Ltd.

Radionuclide adsorption distribution coefficients measured in Hanford sediments for the low level waste performance assessment project

International Nuclear Information System (INIS)

Kaplan, D.I.; Serne, R.J.; Owen, A.T.

1996-08-01

Preliminary modeling efforts for the Hanford Site's Low Level Waste-Performance Assessment (LLW PA) identified 129 I, 237 Np, 79 Se, 99 Tc, and 234 , 235 , 238 U as posing the greatest potential health hazard. It was also determined that the outcome of these simulations was very sensitive to the parameter describing the extent to which radionuclides sorb to the subsurface matrix, i.e., the distribution coefficient (K d ). The distribution coefficient is a ratio of the radionuclide concentration associated with the solid phase to that in the liquid phase. The objectives of this study were to (1) measure iodine, neptunium, technetium, and uranium K d values using laboratory conditions similar to those expected at the LLW PA disposal site, and (2) evaluate the effect of selected environmental parameters, such as pH, ionic strength, moisture concentration, and radio nuclide concentration, on K d values of selected radionuclides. It is the intent of these studies to develop technically defensible K d values for the PA. The approach taken throughout these studies was to measure the key radio nuclide K d values as a function of several environmental parameters likely to affect their values. Such an approach provides technical defensibility by identifying the mechanisms responsible for trends in K d values. Additionally, such studies provide valuable guidance regarding the range of K d values likely to be encountered in the proposed disposal site

Free vibration analysis of straight-line beam regarded as distributed system by combining Wittrick-Williams algorithm and transfer dynamic stiffness coefficient method

Energy Technology Data Exchange (ETDEWEB)

Choi, Myung Soo; Yang, Kyong Uk [Chonnam National University, Yeosu (Korea, Republic of); Kondou, Takahiro [Kyushu University, Fukuoka (Japan); Bonkobara, Yasuhiro [University of Miyazaki, Miyazaki (Japan)

2016-03-15

We developed a method for analyzing the free vibration of a structure regarded as a distributed system, by combining the Wittrick-Williams algorithm and the transfer dynamic stiffness coefficient method. A computational algorithm was formulated for analyzing the free vibration of a straight-line beam regarded as a distributed system, to explain the concept of the developed method. To verify the effectiveness of the developed method, the natural frequencies of straight-line beams were computed using the finite element method, transfer matrix method, transfer dynamic stiffness coefficient method, the exact solution, and the developed method. By comparing the computational results of the developed method with those of the other methods, we confirmed that the developed method exhibited superior performance over the other methods in terms of computational accuracy, cost and user convenience.

Solvent Extraction Batch Distribution Coefficients with Savannah River Site Dissolved Salt Cake

International Nuclear Information System (INIS)

Walker, D.D.

2002-01-01

Researchers characterized high-level waste derived from dissolved salt cake from the Savannah River Site (SRS) tank farm and measured the cesium distribution coefficients (DCs) for extraction, scrub, and stripping steps of the caustic-side solvent extraction (CSSX) flowsheet. The measurements used two SRS high-level waste samples derived entirely or in part from salt cake. The chemical compositions of both samples are reported. Dissolved salt cake waste contained less Cs-137 and more dianions than is typical of supernate samples. Extraction and scrub DCs values for both samples exceeded process requirements and agreed well with model predictions. Strip DCs values for the Tank 46F sample also met process requirements. However, strip DCs values could not be calculated for the Tank 38H sample due to the poor material balance for Cs-137. Potential explanations for the poor material balance are discussed and additional work to determine the cause is described

Quantitative differentiation of breast lesions at 3T diffusion-weighted imaging (DWI) using the ratio of distributed diffusion coefficient (DDC).

Science.gov (United States)

Ertas, Gokhan; Onaygil, Can; Akin, Yasin; Kaya, Handan; Aribal, Erkin

2016-12-01

To investigate the accuracy of diffusion coefficients and diffusion coefficient ratios of breast lesions and of glandular breast tissue from mono- and stretched-exponential models for quantitative diagnosis in diffusion-weighted magnetic resonance imaging (MRI). We analyzed pathologically confirmed 170 lesions (85 benign and 85 malignant) imaged using a 3.0T MR scanner. Small regions of interest (ROIs) focusing on the highest signal intensity for lesions and also for glandular tissue of contralateral breast were obtained. Apparent diffusion coefficient (ADC) and distributed diffusion coefficient (DDC) were estimated by performing nonlinear fittings using mono- and stretched-exponential models, respectively. Coefficient ratios were calculated by dividing the lesion coefficient by the glandular tissue coefficient. A stretched exponential model provides significantly better fits then the monoexponential model (P DDC ratio (area under the curve [AUC] = 0.93) when compared with lesion DDC, ADC ratio, and lesion ADC (AUC = 0.91, 0.90, 0.90) but with no statistically significant difference (P > 0.05). At optimal thresholds, the DDC ratio achieves 93% sensitivity, 80% specificity, and 87% overall diagnostic accuracy, while ADC ratio leads to 89% sensitivity, 78% specificity, and 83% overall diagnostic accuracy. The stretched exponential model fits better with signal intensity measurements from both lesion and glandular tissue ROIs. Although the DDC ratio estimated by using the model shows a higher diagnostic accuracy than the ADC ratio, lesion DDC, and ADC, it is not statistically significant. J. Magn. Reson. Imaging 2016;44:1633-1641. © 2016 International Society for Magnetic Resonance in Medicine.

Distribution coefficients of amino acid, peptide and enzyme in respect to aqueous two phase system composed of dextran, polyethylene glycol and water; Dekisutoran+poriechiren gurikoru+mizu karanaru suiseinisokei ni taisuru aminosan, pepuchido oyobi koso no bunpai keisu

Energy Technology Data Exchange (ETDEWEB)

Iwai, Yoshio [Kyushu University, Fukuoka (Japan); Kakizaka, Keijiro; Shindo, Takashi; Ishida, Otetsu; Arai, Yasuhiko

1999-01-05

Distribution coefficients of five kinds of amino acids (aspartic acid, asparagines, methionine, cysteine and cytidine) and two kinds of peptides (glycylglycine and hexane glycine) were measured. These distribution coefficients are in good correlation with the osmosis viral expression. The interaction parameter in the osmosis viral expression can be estimated by hydrophilic group parameter. The distribution coefficient of {alpha}-amylase was estimated by the osmosis viral expression using the above-mentioned hydrophilic group parameter, and the estimated value showed substantially good correspondence with the actually measured value, but for the distribution coefficient of {beta}-amylase, no coincidence was found. (translated by NEDO)

An employment of distribution coefficients for the valuation of the soils with regard to their radiological risks

International Nuclear Information System (INIS)

Carini, F.; Silva, S.; Fontana, P.

1985-01-01

As a preliminary step it has been demonstrated that the distribution coefficients may prove useful items in order to classify soils to a radioprotective purpose. We have obtained transfer factors from soils, which were different according to their principal chemical and physical features, into plants typical of the middle Po valley agriculture. By utilizing these factors as guiding indexes,it is possible, through cluster analysis, to determine a range of soils with regard to their radiological risk starting only from the pedologic parameters

Comparison of the distribution coefficients of plutonium and other radionuclides in Lake Michigan to those in other systems

International Nuclear Information System (INIS)

Wahlgren, M.A.; Nelson, D.M.

1976-01-01

Filtration of Lake Michigan water samples has been carried out routinely since 1973, and some plutonium concentrations in the seston have been reported. During 1975 and 1976 a sufficient number of filter samples from various depths was obtained throughout the field seasons to establish whether or not a distribution coefficient also controls the uptake of plutonium by the formation of particulates and their settling from the surface waters. Samples from ANL station 5 (10 km SW of Grand Haven, Michigan, water depth 67 m), of the southern basin, and from the lower Great Lakes have been analyzed for dry weight, ash weight, total organic (loss of weight on ignition), amorphous silica, calcite, and residual minerals. Distribution coefficients were calculated on the basis of each of these solid components, and self-consistent values were observed for depth, season, or lake only, on the basis of dry weight of seston. The findings strongly suggest that the uptake of fallout plutonium (including inputs of new fallout during the summer of 1975) is dominated by a surface coating process common to all seston particle types. An insufficient number of 137 Cs analyses were obtained to correlate its uptake to a specific component of the seston, but its behavior is clearly different from that of plutonium

Temperature dependence of Kerr coefficient and quadratic polarized optical coefficient of a paraelectric Mn:Fe:KTN crystal

Directory of Open Access Journals (Sweden)

Qieni Lu

2015-08-01

Full Text Available We measure temperature dependence on Kerr coefficient and quadratic polarized optical coefficient of a paraelectric Mn:Fe:KTN crystal simultaneously in this work, based on digital holographic interferometry (DHI. And the spatial distribution of the field-induced refractive index change can also be visualized and estimated by numerically retrieving sequential phase maps of Mn:Fe:KTN crystal from recording digital holograms in different states. The refractive indices decrease with increasing temperature and quadratic polarized optical coefficient is insensitive to temperature. The experimental results suggest that the DHI method presented here is highly applicable in both visualizing the temporal and spatial behavior of the internal electric field and accurately measuring electro-optic coefficient for electrooptical media.

Comparing linear probability model coefficients across groups

DEFF Research Database (Denmark)

Holm, Anders; Ejrnæs, Mette; Karlson, Kristian Bernt

2015-01-01

of the following three components: outcome truncation, scale parameters and distributional shape of the predictor variable. These results point to limitations in using linear probability model coefficients for group comparisons. We also provide Monte Carlo simulations and real examples to illustrate......This article offers a formal identification analysis of the problem in comparing coefficients from linear probability models between groups. We show that differences in coefficients from these models can result not only from genuine differences in effects, but also from differences in one or more...... these limitations, and we suggest a restricted approach to using linear probability model coefficients in group comparisons....

The role of a detailed aqueous phase source release model in the LANL area G performance assessment

Energy Technology Data Exchange (ETDEWEB)

Vold, E.L.; Shuman, R.; Hollis, D.K. [Los Alamos National Lab., NM (United States)] [and others

1995-12-31

A preliminary draft of the Performance Assessment for the Los Alamos National Laboratory (LANL) low-level radioactive waste disposal facility at Area G is currently being completed as required by Department of Energy orders. A detailed review of the inventory data base records and the existing models for source release led to the development of a new modeling capability to describe the liquid phase transport from the waste package volumes. Nuclide quantities are sorted down to four waste package release categories for modeling: rapid release, soil, concrete/sludge, and corrosion. Geochemistry for the waste packages was evaluated in terms of the equilibrium coefficients, Kds, and elemental solubility limits, Csl, interpolated from the literature. Percolation calculations for the base case closure cover show a highly skewed distribution with an average of 4 mm/yr percolation from the disposal unit bottom. The waste release model is based on a compartment representation of the package efflux, and depends on package size, percolation rate or Darcy flux, retardation coefficient, and moisture content.

Effects of soluble organic complexants and their degradation products on the removal of selected radionuclides from high-level waste. Part II: Distributions of Sr, Cs, Tc, and Am onto 32 absorbers from four variations of Hanford tank 101-SY simulant solution

International Nuclear Information System (INIS)

Marsh, S.F.; Svitra, Z.V.; Bowen, S.M.

1995-04-01

Many of the radioactive waste storage tanks at U.S. Department of Energy facilities contain organic compounds that have been degraded by radiolysis and chemical reactions during decades of storage. In this second part of our three-part investigation of the effects of soluble organic complexants and their degradation products, we measured the sorption of strontium, cesium, technetium, and americium onto 32 absorbers that offer high sorption of these elements in the absence of organic complexants. The four solutions tested were (1) a simulant for a 3:1 dilution of Hanford Tank 101-SY contents that initially contained ethylenediaminetetraacetic acid (EDTA), (2) this simulant after gamma-irradiation to 34 Mrads, (3) the unirradiated simulant after treatment with a hydrothermal organic-destruction process, and (4) the irradiated simulant after hydrothermal processing. For each of 512 element/absorber/solution combinations, we measured distribution coefficients (Kds) twice for each period for dynamic contact periods of 30 min, 2 h, and 6 h to obtain information about sorption kinetics. On the basis of our 3,072 measured Kd values, the sorption of strontium and americium is significantly decreased by the organic components of the simulant solutions, whereas the sorption of cesium and technetium appears unaffected by the organic components of the simulant solutions

Form coefficient of helical toroidal solenoids

International Nuclear Information System (INIS)

Amelin, V.Z.; Kunchenko, V.B.

1982-01-01

For toroidal solenoids with continuous spiral coil, winded according to the laws of equiinclined and simple cylindrical spirals with homogeneous, linearly increasing to the coil periphery and ''Bitter'' distribution of current density, the analytical expressions for the dependence between capacity consumed and generated magnetic field, expressions for coefficients of form similar to Fabry coefficient for cylindrical solenoids are obtained and dependence of the form coefficient and relative volume of solenoid conductor on the number of revolutions of screw line per one circumvention over the large torus radius is also investigated. Analytical expressions of form coefficients and graphical material permit to select the optimum geometry as to capacity consumed both for spiral (including ''force-free'') and conventional toroidal solenoids of magnetic systems in thermonulear installations

Distribution functions to estimate radionuclide solid-liquid distribution coefficients in soils: the case of Cs

Energy Technology Data Exchange (ETDEWEB)

Ramirez-Guinart, Oriol; Rigol, Anna; Vidal, Miquel [Analytical Chemistry department, Faculty of Chemistry, University of Barcelona, Mart i Franques 1-11, 08028, Barcelona (Spain)

2014-07-01

In the frame of the revision of the IAEA TRS 364 (Handbook of parameter values for the prediction of radionuclide transfer in temperate environments), a database of radionuclide solid-liquid distribution coefficients (K{sub d}) in soils was compiled with data coming from field and laboratory experiments, from references mostly from 1990 onwards, including data from reports, reviewed papers, and grey literature. The K{sub d} values were grouped for each radionuclide according to two criteria. The first criterion was based on the sand and clay mineral percentages referred to the mineral matter, and the organic matter (OM) content in the soil. This defined the 'texture/OM' criterion. The second criterion was to group soils regarding specific soil factors governing the radionuclide-soil interaction ('cofactor' criterion). The cofactors depended on the radionuclide considered. An advantage of using cofactors was that the variability of K{sub d} ranges for a given soil group decreased considerably compared with that observed when the classification was based solely on sand, clay and organic matter contents. The K{sub d} best estimates were defined as the calculated GM values assuming that K{sub d} values were always log-normally distributed. Risk assessment models may require as input data for a given parameter either a single value (a best estimate) or a continuous function from which not only individual best estimates but also confidence ranges and data variability can be derived. In the case of the K{sub d} parameter, a suitable continuous function which contains the statistical parameters (e.g. arithmetical/geometric mean, arithmetical/geometric standard deviation, mode, etc.) that better explain the distribution among the K{sub d} values of a dataset is the Cumulative Distribution Function (CDF). To our knowledge, appropriate CDFs has not been proposed for radionuclide K{sub d} in soils yet. Therefore, the aim of this works is to create CDFs for

Evolution of Sr distribution coefficient as a function of time, incubation conditions and measurement technique

International Nuclear Information System (INIS)

Wang Guo; Staunton, Siobhan

2005-01-01

A thorough understanding of the dynamics of radiostrontium in soil is required to allow accurate long-term predictions of its mobility. We have followed the soil solution distribution of 85 Sr as a function of time under controlled conditions over 4 months and studied the effect of soil moisture content and organic matter amendments. Data have been compared to redox conditions and soil pH. To fuel the ongoing debate on the validity of distribution coefficient (K d ) values measured in dilute suspension, we have compared values obtained from the activity concentration in soil solution obtained by centrifugation to data obtained in suspension with or without air-drying of the soil samples after incubation. The 85 Sr adsorption properties of soil, incubated without prior contamination were also measured. There is some time-dependent adsorption of Sr. This is partly due to changing soil composition due to the decomposition of added organic matter and anaerobic conditions induced by flooding. There is also a kinetic effect, but adsorption remains largely reversible. Most of the observed effects are lost when soil is suspended in electrolyte solution

[Assessment of ecosystem in giant panda distribution area based on entropy method and coefficient of variation].

Science.gov (United States)

Yan, Zhi Gang; Li, Jun Qing

2017-12-01

The areas of the habitat and bamboo forest, and the size of the giant panda wild population have greatly increased, while habitat fragmentation and local population isolation have also intensified in recent years. Accurate evaluation of ecosystem status of the panda in the giant panda distribution area is important for giant panda conservation. The ecosystems of the distribution area and six mountain ranges were subdivided into habitat and population subsystems based on the hie-rarchical system theory. Using the panda distribution area as the study area and the three national surveys as the time node, the evolution laws of ecosystems were studied using the entropy method, coefficient of variation, and correlation analysis. We found that with continuous improvement, some differences existed in the evolution and present situation of the ecosystems of six mountain ranges could be divided into three groups. Ecosystems classified into the same group showed many commonalities, and difference between the groups was considerable. Problems of habitat fragmentation and local population isolation became more serious, resulting in ecosystem degradation. Individuali-zed ecological protection measures should be formulated and implemented in accordance with the conditions in each mountain system to achieve the best results.

Distribution coefficients for 85Sr and 137Cs in Japanese agricultural soils and their correlations with soil properties

International Nuclear Information System (INIS)

Kamei-Ishikawa, N.; Uchida, S.; Tagami, K.

2008-01-01

In this work, soil-soil solution distribution coefficients (K d ) of Sr and Cs were obtained for 112 Japanese agricultural soil samples (50 paddy soil and 62 upland soil samples) using batch sorption test. The relationships between Sr- or Cs-K d values and soil properties were discussed. Furthermore, the amount of Cs fixed in soil was estimated for 22 selected soil samples using a sequential extraction method. Then, cross effects of some soil properties for Cs fixation were evaluated. (author)

Estimating the workpiece-backingplate heat transfer coefficient in friction stirwelding

DEFF Research Database (Denmark)

Larsen, Anders; Stolpe, Mathias; Hattel, Jesper Henri

2012-01-01

Purpose - The purpose of this paper is to determine the magnitude and spatial distribution of the heat transfer coefficient between the workpiece and the backingplate in a friction stir welding process using inverse modelling. Design/methodology/approach - The magnitude and distribution of the heat...... in an inverse modeling approach to determine the heat transfer coefficient in friction stir welding. © Emerald Group Publishing Limited....

Unified solution of the Boltzmann equation for electron and ion velocity distribution functions and transport coefficients in weakly ionized plasmas

Science.gov (United States)

Konovalov, Dmitry A.; Cocks, Daniel G.; White, Ronald D.

2017-10-01

The velocity distribution function and transport coefficients for charged particles in weakly ionized plasmas are calculated via a multi-term solution of Boltzmann's equation and benchmarked using a Monte-Carlo simulation. A unified framework for the solution of the original full Boltzmann's equation is presented which is valid for ions and electrons, avoiding any recourse to approximate forms of the collision operator in various limiting mass ratio cases. This direct method using Lebedev quadratures over the velocity and scattering angles avoids the need to represent the ion mass dependence in the collision operator through an expansion in terms of the charged particle to neutral mass ratio. For the two-temperature Burnett function method considered in this study, this amounts to avoiding the need for the complex Talmi-transformation methods and associated mass-ratio expansions. More generally, we highlight the deficiencies in the two-temperature Burnett function method for heavy ions at high electric fields to calculate the ion velocity distribution function, even though the transport coefficients have converged. Contribution to the Topical Issue "Physics of Ionized Gases (SPIG 2016)", edited by Goran Poparic, Bratislav Obradovic, Dragana Maric and Aleksandar Milosavljevic.

Fibroblast growth factor 21 is not required for glucose homeostasis, ketosis and tumour suppression associated to ketogenic diets in mice

Science.gov (United States)

Stemmer, Kerstin; Zani, Fabio; Habegger, Kirk M.; Neff, Christina; Kotzbeck, Petra; Bauer, Michaela; Yalamanchilli, Suma; Azad, Ali; Lehti, Maarit; Martins, Paulo J.F.; Müller, Timo D.; Pfluger, Paul T.; Seeley, Randy J.

2016-01-01

AIMS/HYPOTHESIS Ketogenic diets (KDs) increasingly gained attention as effective means for weight loss and potential adjunctive treatment of cancer. Metabolic benefits of KDs are regularly ascribed towards enhanced hepatic secretion of fibroblast growth factor (FGF) 21, and its systemic effects on fatty acid oxidation, energy expenditure and body weight. Ambiguous data from Fgf21 knockout strains and low FGF21 concentrations reported for humans in ketosis have nevertheless cast doubt regarding the endogenous function of FGF21. We here aimed to elucidate the causal role of FGF21 in mediating therapeutic benefits of KDs on metabolism and cancer. METHODS We established a dietary model of increased vs. decreased FGF21 by feeding C57BL/6J mice with KDs, either depleted or enriched with protein, respectively. We furthermore used wild type and Fgf21 knockout mice that were subjected to the respective diets, and monitored energy and glucose homeostasis as well as tumor growth after transplantation of Lewis-Lung-Carcinoma cells. RESULTS Hepatic and circulating but not adipose tissue FGF21 levels were profoundly increased by protein starvation and independent of the state of ketosis. We demonstrate that endogenous FGF21 is not essential for the maintenance of normoglycemia upon protein and carbohydrate starvation and is dispensable for the effects of KDs on energy expenditure. Furthermore, the tumor-suppressing effects of KDs were independent from FGF21, and rather driven by concomitant protein and carbohydrate starvation. CONCLUSION/INTERPRETATION Our data indicate that multiple systemic effects of KDs exposure in mice that were previously ascribed towards increased FGF21 secretion are rather a consequence of protein malnutrition. PMID:26099854

Studies on simulated nuclear waste of mixed solvent type

International Nuclear Information System (INIS)

Aggarwal, S.

1989-09-01

Caesium 137, strontium 90 and ruthenium 106 are among the longest lived fission products present in reprocessing wastes and are therefore considered to be a long term hazard to the environment. A method for removal of 137-Cs, 90-Sr and 106-Ru from the nuclear waste is by ion-exchange and sorption. Radiochemical methods were employed to investigate the uptake of 137-Cs, 90-Sr and 106-Ru by synthetic type A, X, Y, zeolites and by mordenite and clinoptilolite. The solvents employed were tributylphosphate (TBP) and kerosene (OK). The dependence of the exchange process on time was studied at room temperature. The exchange equilibrium was strongly dependent on time during the first hour but then attained equilibrium. It was also noted that the distribution coefficient (Kd) values for 137-Cs were higher than those for 90-Sr which were higher than those for 106-Ru. Thus the order of extraction was: 137-Cs > 90-Sr > 106-Ru. Ethanol was also used as the solvent to see the effect on the Kds by varying the amount of water present, i.e. from 0% water to 10% water. It was observed that the Kd increased with an increase in water content. The effect of pH and different ratios of TBP:OK were also studied. There was no relationship between the Kds and the different ratios. Some work was also done on the adsorption of 137-Cs on cements and cement phases. The sorption of 137-Cs on to all types of cements was low. (author)

Estimating Runoff Coefficients Using Weather Radars

DEFF Research Database (Denmark)

Ahm, Malte; Thorndahl, Søren Liedtke; Rasmussen, Michael R.

2012-01-01

This paper presents a method for estimating runoff coefficients of urban drainage catchments based on a combination of high resolution weather radar data and insewer flow measurements. By utilising the spatial variability of the precipitation it is possible to estimate the runoff coefficients...... of separate subcatchments. The method is demonstrated through a case study of an urban drainage catchment (678ha) located in the municipality of Aarhus, Denmark. The study has proven it is possible to use corresponding measurements of the relative rainfall distribution over the catchment and runoff...... measurements to identify the runoff coefficients at subcatchment level. The number of potential subcatchments is limited by the number of available rainfall events with a sufficient spatial variability....

Algebraic polynomials with random coefficients

Directory of Open Access Journals (Sweden)

K. Farahmand

2002-01-01

Full Text Available This paper provides an asymptotic value for the mathematical expected number of points of inflections of a random polynomial of the form a0(ω+a1(ω(n11/2x+a2(ω(n21/2x2+…an(ω(nn1/2xn when n is large. The coefficients {aj(w}j=0n, w∈Ω are assumed to be a sequence of independent normally distributed random variables with means zero and variance one, each defined on a fixed probability space (A,Ω,Pr. A special case of dependent coefficients is also studied.

Estimation Of The Spatial Distribution Of Crop Coefficient (Kc) From Landsat Satellite Imagery

International Nuclear Information System (INIS)

Abou EI-Magd, I.H.

2009-01-01

Single crop coefficient factor (K c ) is an essential component for crop water allocation for efficient irrigation scheduling and irrigation water management. Kc is basically defined as the ratio of actual evapotranspiration and grass/alfalfa reference evapotranspiration and always measured by lysimeter in localized area in the field, which then generalized on the whole irrigated land. The lack of precise information about the crop coefficient particularly in our country together with both small sized fields and heterogeneity of agricultural crops calls for developing a new methodology for computing a real time crop coefficient from remotely sensed data. This paper discusses the methodology developed for obtaining a real time single crop coefficient from Landsat Satellite ETM + 7 imageries. The methodology was applied and optimized on one irrigation field with two different dates and crop cover in the northern Delta of Egypt

Effect of water content on strontium retardation factor and distribution coefficient in Chinese loess.

Science.gov (United States)

Huo, Lijuan; Qian, Tianwei; Hao, Junting; Liu, Hongfang; Zhao, Dongye

2013-12-01

Geological burial and landfill are often employed for disposal of nuclear wastes. Typically, radionuclides from nuclear facilities transport through the unsaturated zone before reaching the groundwater aquifer. However, transport studies are often conducted under saturated and steady-state flow conditions. This research aimed to examine the effects of unsaturated flow conditions and soil water content (θ) on Sr sorption and retardation in Chinese loess through 1D column transport experiments. Reagent SrCl2 was used as a surrogate for the radioactive isotope ((90)Sr) in the experiment because of their analogous adsorption and transportation characteristics. The spatial distribution of Sr along the column length was determined by segmenting the soil bed and analysing the Sr content in each soil segment following each column breakthrough test. The single-region (SR) and two-region (TR) models were employed to interpret the transport data of Sr as well as a tracer (Br(-)), which resulted in the dispersion coefficient (D) and retardation factor (Rd) under a given set of unsaturated flow conditions. For the tracer, the SR and TR models offered nearly the same goodness of fitting to the breakthrough curves (R(2) ≈ 0.97 for both models). For the highly sorptive Sr, however, the TR model provided better fitting (R(2), 0.80-0.96) to the Sr retention profiles than the SR model (R(2), 0.20-0.89). The Sr retention curves exhibited physical non-equilibrium characteristics, particularly at lower water content of the soil. For the unsaturated soil, D and the pore water velocity (v) displayed a weak linear correlation, which is attributed to the altering dispersivity as the water content varies. A much improved linear correlation was observed between D and v/θ. The retardation factor of Sr increased from 69.1 to 174.2 as θ decreased from 0.46 to 0.26 (cm(3) cm(-3)), while the distribution coefficient (Kd) based on Rd remained nearly unchanged at various θ levels. These

Diffusion coefficient adaptive correction in Lagrangian puff model

International Nuclear Information System (INIS)

Tan Wenji; Wang Dezhong; Ma Yuanwei; Ji Zhilong

2014-01-01

Lagrangian puff model is widely used in the decision support system for nuclear emergency management. The diffusion coefficient is one of the key parameters impacting puff model. An adaptive method was proposed in this paper, which could correct the diffusion coefficient in Lagrangian puff model, and it aimed to improve the accuracy of calculating the nuclide concentration distribution. This method used detected concentration data, meteorological data and source release data to estimate the actual diffusion coefficient with least square method. The diffusion coefficient adaptive correction method was evaluated by Kincaid data in MVK, and was compared with traditional Pasquill-Gifford (P-G) diffusion scheme method. The results indicate that this diffusion coefficient adaptive correction method can improve the accuracy of Lagrangian puff model. (authors)

Estimating varying coefficients for partial differential equation models.

Science.gov (United States)

Zhang, Xinyu; Cao, Jiguo; Carroll, Raymond J

2017-09-01

Partial differential equations (PDEs) are used to model complex dynamical systems in multiple dimensions, and their parameters often have important scientific interpretations. In some applications, PDE parameters are not constant but can change depending on the values of covariates, a feature that we call varying coefficients. We propose a parameter cascading method to estimate varying coefficients in PDE models from noisy data. Our estimates of the varying coefficients are shown to be consistent and asymptotically normally distributed. The performance of our method is evaluated by a simulation study and by an empirical study estimating three varying coefficients in a PDE model arising from LIDAR data. © 2017, The International Biometric Society.

Transitions in genetic toggle switches driven by dynamic disorder in rate coefficients

International Nuclear Information System (INIS)

Chen, Hang; Thill, Peter; Cao, Jianshu

2016-01-01

In biochemical systems, intrinsic noise may drive the system switch from one stable state to another. We investigate how kinetic switching between stable states in a bistable network is influenced by dynamic disorder, i.e., fluctuations in the rate coefficients. Using the geometric minimum action method, we first investigate the optimal transition paths and the corresponding minimum actions based on a genetic toggle switch model in which reaction coefficients draw from a discrete probability distribution. For the continuous probability distribution of the rate coefficient, we then consider two models of dynamic disorder in which reaction coefficients undergo different stochastic processes with the same stationary distribution. In one, the kinetic parameters follow a discrete Markov process and in the other they follow continuous Langevin dynamics. We find that regulation of the parameters modulating the dynamic disorder, as has been demonstrated to occur through allosteric control in bistable networks in the immune system, can be crucial in shaping the statistics of optimal transition paths, transition probabilities, and the stationary probability distribution of the network.

Transitions in genetic toggle switches driven by dynamic disorder in rate coefficients

Energy Technology Data Exchange (ETDEWEB)

Chen, Hang, E-mail: hangchen@mit.edu; Thill, Peter; Cao, Jianshu [Department of Chemistry, Massachusetts Institute of Technology, Cambridge, Massachusetts 02139 (United States)

2016-05-07

In biochemical systems, intrinsic noise may drive the system switch from one stable state to another. We investigate how kinetic switching between stable states in a bistable network is influenced by dynamic disorder, i.e., fluctuations in the rate coefficients. Using the geometric minimum action method, we first investigate the optimal transition paths and the corresponding minimum actions based on a genetic toggle switch model in which reaction coefficients draw from a discrete probability distribution. For the continuous probability distribution of the rate coefficient, we then consider two models of dynamic disorder in which reaction coefficients undergo different stochastic processes with the same stationary distribution. In one, the kinetic parameters follow a discrete Markov process and in the other they follow continuous Langevin dynamics. We find that regulation of the parameters modulating the dynamic disorder, as has been demonstrated to occur through allosteric control in bistable networks in the immune system, can be crucial in shaping the statistics of optimal transition paths, transition probabilities, and the stationary probability distribution of the network.

APPROXIMATION OF PROBABILITY DISTRIBUTIONS IN QUEUEING MODELS

Directory of Open Access Journals (Sweden)

T. I. Aliev

2013-03-01

Full Text Available For probability distributions with variation coefficient, not equal to unity, mathematical dependences for approximating distributions on the basis of first two moments are derived by making use of multi exponential distributions. It is proposed to approximate distributions with coefficient of variation less than unity by using hypoexponential distribution, which makes it possible to generate random variables with coefficient of variation, taking any value in a range (0; 1, as opposed to Erlang distribution, having only discrete values of coefficient of variation.

Modified Regression Correlation Coefficient for Poisson Regression Model

Science.gov (United States)

Kaengthong, Nattacha; Domthong, Uthumporn

2017-09-01

This study gives attention to indicators in predictive power of the Generalized Linear Model (GLM) which are widely used; however, often having some restrictions. We are interested in regression correlation coefficient for a Poisson regression model. This is a measure of predictive power, and defined by the relationship between the dependent variable (Y) and the expected value of the dependent variable given the independent variables [E(Y|X)] for the Poisson regression model. The dependent variable is distributed as Poisson. The purpose of this research was modifying regression correlation coefficient for Poisson regression model. We also compare the proposed modified regression correlation coefficient with the traditional regression correlation coefficient in the case of two or more independent variables, and having multicollinearity in independent variables. The result shows that the proposed regression correlation coefficient is better than the traditional regression correlation coefficient based on Bias and the Root Mean Square Error (RMSE).

Estimation of uranium isotopes in soil affected by Fukushima nuclear power plant accident and its mobility based on distribution coefficient and soil properties

Energy Technology Data Exchange (ETDEWEB)

Sahoo, S.K. [National Institute of Radiological Sciences (Japan); Mishra, S. [Bhabha Atomic Research Centre (India); Sorimachi, A.; Hosoda, M.; Tokonami, S. [Hirosaki University (Japan); Kritsananuwat, R. [Tokyo Metropolitan University (Japan); Ishikawa, T. [Fukushima Medical University (Japan)

2014-07-01

An extraordinary earthquake of magnitude 9.0 followed by Tsunami on 11 March 2011 caused serious nuclear accident at the Fukushima Daiichi Nuclear Power Plant (FDNPP) about 250 km north to Tokyo, capital of Japan. This resulted in radioactive contamination due to deposition of long-lived radionuclides. Contaminated soil can cause an enhanced radiation exposure even after many years. Depending upon environmental conditions radionuclides can be mobilized to aquatic systems. Therefore, the fate and transfer of these radionuclides in the soil water system is very important for radiation protection and dose assessment. In the present study, emphasis has been given on isotope ratio measurement of uranium that may give some idea about its contamination during accident. Soil and water samples were collected from contaminated areas around FDNPP. Inductively coupled plasma mass spectrometry (ICPMS) is used for total uranium concentration and thermal ionization mass spectrometry (TIMS) has been used for uranium isotopes measurement. Extraction chromatography has been used for the separation of uranium. We have observed, isotope ratio {sup 235}U/{sup 238}U is of natural origin, however in a few soil samples {sup 236}U has been detected. For the migration behavior, its distribution coefficient (K{sub d}) has been determined using laboratory batch method. Depleted uranium is used as tracer for uranium K{sub d} estimation. Chemical characterization of soil with respect to different parameters has been carried out. The effect of these soil parameters on distribution coefficient of uranium has been studied in order to explain the radionuclide mobility in this particular area. The distribution coefficient values for uranium are found to vary from 30-35679 L/Kg. A large variation in the distribution coefficient values shows the retention or mobility of uranium is highly dependent on soil characteristics in the particular area. This variation is explained with respect to pH, Fe, Mn

Relativistic neoclassical transport coefficients with momentum correction

International Nuclear Information System (INIS)

Marushchenko, I.; Azarenkov, N.A.

2016-01-01

The parallel momentum correction technique is generalized for relativistic approach. It is required for proper calculation of the parallel neoclassical flows and, in particular, for the bootstrap current at fusion temperatures. It is shown that the obtained system of linear algebraic equations for parallel fluxes can be solved directly without calculation of the distribution function if the relativistic mono-energetic transport coefficients are already known. The first relativistic correction terms for Braginskii matrix coefficients are calculated.

Microscopic coefficients for the quantum master equation of a Fermi system

International Nuclear Information System (INIS)

Stefanescu, E.; Sandulescu, A.

2002-01-01

In a previous paper, we derived a master equation for fermions, of Lindblad's form, with coefficients depending on microscopic quantities. In this paper, we study the properties of the dissipative coefficients taking into account the explicit expressions of: (a) the matrix elements of the dissipative potential, evaluated from the condition that, essentially, this potential induces transitions among the system eigenstates without significantly modifying these states, (b) the densities of the environment states according to the Thomas-Fermi model, and (c) the occupation probabilities of these states taken as a Fermi-Dirac distribution. The matrix of these coefficients correctly describes the system dynamics: (a) for a normal, Fermi-Dirac distribution of the environment population, the decays dominate the excitation processes; (b) for an inverted (exotic) distribution of this population, specific to a clustering state, the excitation processes are dominant. (author)

Geochemical and physical properties, distribution coefficients of soils and sediments at the Olkiluoto Island and in the reference area in 2010-2011

International Nuclear Information System (INIS)

Lahdenperae, A.-M.

2014-04-01

The report summarises the chemical, physical and mineralogical data and the calculated 'in situ' distribution coefficients (K d ) values of the indigenous elements from the different types of soil and sediment samples at the Olkiluoto Island and in the Reference area that were taken in 2010-2011. The data has been collected in order to extend the understanding of the site evolution and for radionuclide transport analyses and modelling. 'In situ' distribution coefficients, K d values are used to indicate the relevant mobility of elements and radionuclides. This report is part of the entirety of soil and sediment data from different soil types, soil layers and environmental conditions collected earlier for the biosphere site description and development. Soil and sediment samples were taken at various depths of humus, peat, gyttja, sandy/fine sandy till and cropland soils. The analyses procedure varied to some extent between the samples. In all samples were analysed pH, LOI, C, N, and the total concentrations of the elements using HNO 3 -HF extraction. The 'in situ' K d values were calculated using the formula by Sheppard et al.. For selected samples the easily leachable fraction was analysed by NH 4 Ac (pH 4.5). Bulk density and mineralogy was determined for a few samples. Grain size distribution was measured only from till samples. The results are discussed and the physical-chemical data and distribution coefficients of the results are presented. The cation exchange capacity and base saturation are calculated for the sandy/fine sandy till samples from Olkiluoto. The K d values of the important indigenous elements Ag, Cl, Cs, I, Mo, Ni, Se and Sr are of main interest in biosphere development due to the longest half-lives of the associated radionuclides, thus having long interaction times. The K d data are inherently extremely variable due to nature of practical quantity in question, aggregating a number of processes into a single value, but the data also vary

Geochemical and physical properties, distribution coefficients of soils and sediments at the Olkiluoto Island and in the reference area in 2010-2011

Energy Technology Data Exchange (ETDEWEB)

Lahdenperae, A.-M. [Saanio and Riekkola Oy, Helsinki (Finland)

2014-04-15

The report summarises the chemical, physical and mineralogical data and the calculated 'in situ' distribution coefficients (K{sub d}) values of the indigenous elements from the different types of soil and sediment samples at the Olkiluoto Island and in the Reference area that were taken in 2010-2011. The data has been collected in order to extend the understanding of the site evolution and for radionuclide transport analyses and modelling. 'In situ' distribution coefficients, K{sub d} values are used to indicate the relevant mobility of elements and radionuclides. This report is part of the entirety of soil and sediment data from different soil types, soil layers and environmental conditions collected earlier for the biosphere site description and development. Soil and sediment samples were taken at various depths of humus, peat, gyttja, sandy/fine sandy till and cropland soils. The analyses procedure varied to some extent between the samples. In all samples were analysed pH, LOI, C, N, and the total concentrations of the elements using HNO{sub 3}-HF extraction. The 'in situ' K{sub d} values were calculated using the formula by Sheppard et al.. For selected samples the easily leachable fraction was analysed by NH{sub 4}Ac (pH 4.5). Bulk density and mineralogy was determined for a few samples. Grain size distribution was measured only from till samples. The results are discussed and the physical-chemical data and distribution coefficients of the results are presented. The cation exchange capacity and base saturation are calculated for the sandy/fine sandy till samples from Olkiluoto. The K{sub d} values of the important indigenous elements Ag, Cl, Cs, I, Mo, Ni, Se and Sr are of main interest in biosphere development due to the longest half-lives of the associated radionuclides, thus having long interaction times. The K{sub d} data are inherently extremely variable due to nature of practical quantity in question, aggregating a number of

Interpretation of diffusion coefficients in nanostructured materials from random walk numerical simulation.

Science.gov (United States)

Anta, Juan A; Mora-Seró, Iván; Dittrich, Thomas; Bisquert, Juan

2008-08-14

We make use of the numerical simulation random walk (RWNS) method to compute the "jump" diffusion coefficient of electrons in nanostructured materials via mean-square displacement. First, a summary of analytical results is given that relates the diffusion coefficient obtained from RWNS to those in the multiple-trapping (MT) and hopping models. Simulations are performed in a three-dimensional lattice of trap sites with energies distributed according to an exponential distribution and with a step-function distribution centered at the Fermi level. It is observed that once the stationary state is reached, the ensemble of particles follow Fermi-Dirac statistics with a well-defined Fermi level. In this stationary situation the diffusion coefficient obeys the theoretical predictions so that RWNS effectively reproduces the MT model. Mobilities can be also computed when an electrical bias is applied and they are observed to comply with the Einstein relation when compared with steady-state diffusion coefficients. The evolution of the system towards the stationary situation is also studied. When the diffusion coefficients are monitored along simulation time a transition from anomalous to trap-limited transport is observed. The nature of this transition is discussed in terms of the evolution of electron distribution and the Fermi level. All these results will facilitate the use of RW simulation and related methods to interpret steady-state as well as transient experimental techniques.

Stress Optical Coefficient, Test Methodology, and Glass Standard Evaluation

Science.gov (United States)

2016-05-01

ARL-TN-0756 ● MAY 2016 US Army Research Laboratory Stress Optical Coefficient, Test Methodology , and Glass Standard Evaluation...Stress Optical Coefficient, Test Methodology , and Glass Standard Evaluation by Clayton M Weiss Oak Ridge Institute for Science and Education...ORISE), Belcamp, MD Parimal J Patel Weapons and Materials Research Directorate, ARL Approved for public release; distribution is

Existence and global exponential stability of periodic solution to BAM neural networks with periodic coefficients and continuously distributed delays

International Nuclear Information System (INIS)

Zhou Tiejun; Chen Anping; Zhou Yuyuan

2005-01-01

By using the continuation theorem of coincidence degree theory and Liapunov function, we obtain some sufficient criteria to ensure the existence and global exponential stability of periodic solution to the bidirectional associative memory (BAM) neural networks with periodic coefficients and continuously distributed delays. These results improve and generalize the works of papers [J. Cao, L. Wang, Phys. Rev. E 61 (2000) 1825] and [Z. Liu, A. Chen, J. Cao, L. Huang, IEEE Trans. Circuits Systems I 50 (2003) 1162]. An example is given to illustrate that the criteria are feasible

Existence and global exponential stability of periodic solution to BAM neural networks with periodic coefficients and continuously distributed delays

Science.gov (United States)

Zhou, distributed delays [rapid communication] T.; Chen, A.; Zhou, Y.

2005-08-01

By using the continuation theorem of coincidence degree theory and Liapunov function, we obtain some sufficient criteria to ensure the existence and global exponential stability of periodic solution to the bidirectional associative memory (BAM) neural networks with periodic coefficients and continuously distributed delays. These results improve and generalize the works of papers [J. Cao, L. Wang, Phys. Rev. E 61 (2000) 1825] and [Z. Liu, A. Chen, J. Cao, L. Huang, IEEE Trans. Circuits Systems I 50 (2003) 1162]. An example is given to illustrate that the criteria are feasible.

Dielectronic recombination rate coefficients to excited states of Be-like oxygen

Energy Technology Data Exchange (ETDEWEB)

Murakami, Izumi; Safronova, Ulyana I.; Kato, Takako

2001-05-01

We have calculated energy levels, radiative transition probabilities, and autoionization rates for Be-like oxygen (O{sup 4+}) including ls{sup 2}2lnl' (n=2 - 8, l {<=} n - 1) and 1s{sup 2}3l'nl (n=3 - 6, l {<=} n - l) states by multi-configurational Hartree-Fock method (Cowan code) and perturbation theory Z-expansion method (MZ code). The state selective dielectronic recombination rate coefficients to excited states of Be-like O ions are obtained. Configuration mixing plays an important role for the principal quantum number n distribution of the dielectronic recombination rate coefficients for 2snl (n {<=} 5) levels at low electron temperature. The orbital angular momentum quantum number l distribution of the rate coefficients shows a peak at l = 4. The total dielectronic recombination rate coefficient is derived as a function of electron temperature. (author)

Evaluation of distribution coefficients and concentration ratios of (90)Sr and (137)Cs in the Techa River and the Miass River.

Science.gov (United States)

Shishkina, E A; Pryakhin, E A; Popova, I Ya; Osipov, D I; Tikhova, Yu; Andreyev, S S; Shaposhnikova, I A; Egoreichenkov, E A; Styazhkina, E V; Deryabina, L V; Tryapitsina, G A; Melnikov, V; Rudolfsen, G; Teien, H-C; Sneve, M K; Akleyev, A V

2016-07-01

Empirical data on the behavior of radionuclides in aquatic ecosystems are needed for radioecological modeling, which is commonly used for predicting transfer of radionuclides, estimating doses, and assessing possible adverse effects on species and communities. Preliminary studies of radioecological parameters including distribution coefficients and concentration ratios, for (90)Sr and (137)Cs were not in full agreement with the default values used in the ERICA Tool and the RESRAD BIOTA codes. The unique radiation situation in the Techa River, which was contaminated by long-lived radionuclides ((90)Sr and (137)Cs) in the middle of the last century allows improved knowledge about these parameters for river systems. Therefore, the study was focused on the evaluation of radioecological parameters (distribution coefficients and concentration ratios for (90)Sr and (137)Cs) for the Techa River and the Miass River, which is assumed as a comparison waterbody. To achieve the aim the current contamination of biotic and abiotic components of the river ecosystems was studied; distribution coefficients for (90)Sr and (137)Cs were calculated; concentration ratios of (90)Sr and (137)Cs for three fish species (roach, perch and pike), gastropods and filamentous algae were evaluated. Study results were then compared with default values available for use in the well-known computer codes ERICA Tool and RESRAD BIOTA (when site-specific data are not available). We show that the concentration ratios of (137)Cs in whole fish bodies depend on the predominant type of nutrition (carnivores and phytophagous). The results presented here are useful in the context of improving of tools for assessing concentrations of radionuclides in biota, which could rely on a wider range of ecosystem information compared with the process limited the current versions of ERICA and RESRAD codes. Further, the concentration ratios of (90)Sr are species-specific and strongly dependent on Ca(2+) concentration in

Comparison of distributed vortex receptivity coefficients at excitation of 3D TS-waves in presence and absence of surface waviness and pressure gradient

Science.gov (United States)

Borodulin, V. I.; Ivanov, A. V.; Kachanov, Y. S.; Mischenko, D. A.; Fedenkova, A. A.

2016-10-01

The paper is devoted to quantitative experimental investigation of effective mechanisms of excitation of 3D TS instability waves due to distributed boundary layer receptivity to free-stream vortices. Experiments carried out in a self-similar boundary layer with Hartree parameter βH = -0.115 and concentrated on studying two receptivity mechanisms connected with distributed scattering of 3D unsteady free-stream vortices both on the natural boundary layer nonuniformity (smooth surface) and on 2D surface nonuniformity (waviness). Obtained quantitative characteristics (distributed receptivity coefficients) are compared directly with those obtained in Blasius boundary layer. It is found that the adverse pressure gradient leads to reduction of efficiency of the vortex-roughness receptivity mechanism.

Distribution coefficients of different soil types at Olkiluoto repository site and its surroundings, southwestern Finland

Energy Technology Data Exchange (ETDEWEB)

Lahdenperae, Anne-Maj [Saanio and Riekkola Oy, Laulukuja 4, FI-00420 Helsinki (Finland); Ikonen, Ari T.K. [Environmental Research and Assessment EnviroCase, Ltd., Hallituskatu 1 D 4, 28100 Pori (Finland)

2014-07-01

In Finland, the Olkiluoto Island on the western coast has been selected as a repository site for the spent nuclear fuel. Due to shallow sea areas around the island, the post-glacial crustal rebound (around 6 mm/y) is changing the landscape significantly; during the next thousands of years new soil types are emerging, the present bays will narrow and form future lakes and mires assumedly similar to those farther inland at present. The effects of terrain development are important in long-term safety assessments for the repository, especially in the biosphere assessments addressing radiation exposure of people and biota in scenarios of radionuclide releases. 'In situ' distribution coefficients, K{sub d} values are used to indicate the relevant mobility of radionuclides of concern from nuclear waste. These radionuclides have very long half-lives and long interaction times with soils, ranging from centuries to millennia. By measuring the desorption K{sub d} values of the indigenous stable elements (Ag, Cl, Cs, I, Mo, Nb, Ni, Se and Sr) from field moist samples are a valid description of slow retention processes. The 'in situ' K{sub d} desorption values are calculated for humus, peat and different mineral soil samples taken from the Olkiluoto Island and the Reference Area used as an analogue of the future terrain. The solids are extracted alternatively by HNO{sub 3}-HF and NH{sub 4}Ac (pH 4.5). The K{sub d} values are highly dependent on environmental factors, including but not limited to pH, soil type, soil horizon, soil body, texture, element chemical form, organic matter, carbon content and biological activity. This is discussed in the contribution; e.g., for several elements pH and K{sub d} values correlate - the finer the soil or sediment, the higher the K{sub d} values - and humus and peat samples have a clear correlation with the organic matter and carbon contents. The contribution also compares the 'in situ' K{sub d} values to

Out-of-order event processing in kinetic data structures

DEFF Research Database (Denmark)

Abam, Mohammad; de Berg, Mark; Agrawal, Pankaj

2011-01-01

’s for the maintenance of several fundamental structures such as kinetic sorting and kinetic tournament trees, which overcome the difficulty by employing a refined event scheduling and processing technique. We prove that the new event scheduling mechanism leads to a KDS that is correct except for finitely many short......We study the problem of designing kinetic data structures (KDS’s for short) when event times cannot be computed exactly and events may be processed in a wrong order. In traditional KDS’s this can lead to major inconsistencies from which the KDS cannot recover. We present more robust KDS...

Albedo-adjusted fast-neutron diffusion coefficients in reactor reflectors

International Nuclear Information System (INIS)

Terney, W.B.

1975-01-01

In the newer, larger pressurized-water reactor cores, the calculated power distributions are fairly sensitive to the number of neutron groups used and to the treatment of the reflector cross sections. Comparisons between transport and diffusion calculations show that the latter substantially underpredict the reflector albedos in the fast (top) group and that the power distribution is shifted toward the core center when compared to 4-group transport theory results. When the fast-neutron diffusion coefficients are altered to make the transport- and diffusion-theory albedos agree, the power distributions are also brought into agreement. An expression for the fast-neutron diffusion coefficients in reflector regions has been derived such that the diffusion calculation reproduces the albedo obtained from a transport solution. In addition, a correction factor for mesh effects applicable to coarse mesh problems is presented. The use of the formalism gives the correct albedos and improved power distributions. (U.S.)

Conversion coefficients and yrast state spins in 180Os

International Nuclear Information System (INIS)

Dracoulis, G.D.; Kibedi, T.; Byrne, A.P.; Fabricius, B.; Stuchbery, A.E.

1989-11-01

Internal conversion coefficients of transitions in 180 Os have been measured using a superconducting, solenoidal electron spectrometer, operated in the lens mode. The high energy resolution and efficiency allow a precise measurement of the conversion coefficients of the 528 keV yrast transition. The values obtained, α K = 0.015 (2), α L = 0.004(1) define pure E2 multipolarity. Taken with the measured γ-ray angular distribution, the conversion coefficient leads to an unambiguous assignment of 16 + →14 + for the 528 keV transition. 14 refs., 5 figs., 1 tab

Optimized probabilistic calibration of safety coefficients in defect severity assessments; Dimensionnement probabiliste optimise des coefficients de securite dans les etudes de nocivite de defauts

Energy Technology Data Exchange (ETDEWEB)

Ardillon, E.; Pitner, P.; Barthelet, B. [Electricite de France, Direction des Etudes at Recherches, 92 - Clamart (France)

1997-12-31

The construction codes currently used in nuclear engineering recommend analysis methods and criteria consistent with a deterministic approach. Since 1993, in the framework of work related to the RSEM codes, the EFMT Branch has launched a probabilistic approach to establish a link between the current `deterministic` rules and failure risk assessments for the structures considered. There is an explicit link between the two approaches in the elementary strength/load case where the variables are Gaussian. This case provides the basis for the proposed methodology. In the complex case discussed in this paper, involving cracked piping with numerous non-Gaussian inputs, for a given failure mode, there is an implicit relationship between the target reliability level and the partial safety coefficients attached to each variable. The mean flaw size is the intermediate parameter used to make this link and allows flexibility in the choice of coefficients, thereby raising the question of optimized calibration. The approach is illustrated by the choice of coefficients based on the coordinates of the most probable failure point, resulting in a single set of coefficients adapted to the immediate vicinity of a given situation. In cases where the criterion must guarantee a given reliability level for a number of different operating situations, no set of coefficients can entirely guarantee the target reliability level. So, an optimized set of coefficients has to be selected, ensuring a reliability level as uniform as possible over the scope considered. This paper compares an initial coefficient proposal with a choice based on the design point method. The intermediate variable in assessing the reliability level is the mean flaw size, which would seem compatible with problems encountered under operating conditions. In addition, realistic risk assessment requires validation of the main variable distribution assumptions. We give an example of adjustment of distribution assumptions to

DETERMINATION OF MOISTURE DIFFUSION COEFFICIENT OF LARCH BOARD WITH FINITE DIFFERENCE METHOD

Directory of Open Access Journals (Sweden)

Qiaofang Zhou

2011-04-01

Full Text Available This paper deals with the moisture diffusion coefficient of Dahurian Larch (Larix gmelinii Rupr. by use of the Finite Difference Method (FDM. To obtain moisture distributions the dimensional boards of Dahurian Larch were dried, from which test samples were cut and sliced evenly into 9 pieces in different drying periods, so that moisture distributions at different locations and times across the thickness of Dahurian Larch were obtained with a weighing method. With these experimental data, FDM was used to solve Fick’s one-dimensional unsteady-state diffusion equation, and the moisture diffusion coefficient across the thickness at specified time was obtained. Results indicated that the moisture diffusion coefficient decreased from the surface to the center of the Dahurian Larch wood, and it decreased with decreasing moisture content at constant wood temperature; as the wood temperature increased, the moisture diffusion coefficient increased, and the effect of the wood temperature on the moisture diffusion coefficient was more significant than that of moisture content. Moisture diffusion coefficients were different for the two experiments due to differing diffusivity of the specimens.

Measurement of distribution coefficients using a radial injection dual-tracer test

International Nuclear Information System (INIS)

Pickens, J.F.; Jackson, R.E.; Inch, K.J.; Merritt, W.F.

1981-01-01

The dispersive and adsorptive properties of a sandy aquifer were evaluated by using a radial injection dual-tracer test with 131 I as the nonreactive tracer and 85 Sr as the reactive tracer. The tracer migration was monitored by using multilevel point-sampling devices located at various radial distances and depths. Nonequilibrium physical and chemical adsorption effects for 85 Sr were treated as a spreading or dispersion mechanism in the breakthrough curve analysis. The resulting effective dispersivity values for 85 Sr were typically a factor of 2 to 5 larger than those obtained for 131 I. The distribution coefficient (K/sub d//sup Sr/) values obtained from analysis of the breakthrough curves at three depths and two radial distances ranged from 2.6 to 4.5 ml/g. These compare favorably with values obtained by separation of fluids from solids in sediment cores, by batch experiments on core sediments and by analysis of a 25-year-old radioactive waste plume in another part of the same aquifer. Correlations of adsorbed 85 Sr radioactivity with grain size fractions demonstrated preferential adsorption to the coarsest fraction and to the finest fraction. The relative amounts of electrostatically and specifically adsorbed 85 Sr on the aquifer sediments were determined with desorption experiments on core sediments using selective chemical extractants. The withdrawal phase breakthrough curves for the well, obtained immediately following the injection phase, showed essentially full tracer recoveries for both 131 I and 85 Sr. Relatively slow desorption of 85 Sr provided further indication of the nonequilibrium nature of the adsorption-desorption phenomena

Breakdown coefficients and scaling properties of rain fields

Directory of Open Access Journals (Sweden)

D. Harris

1998-01-01

Full Text Available The theory of scale similarity and breakdown coefficients is applied here to intermittent rainfall data consisting of time series and spatial rain fields. The probability distributions (pdf of the logarithm of the breakdown coefficients are the principal descriptor used. Rain fields are distinguished as being either multiscaling or multiaffine depending on whether the pdfs of breakdown coefficients are scale similar or scale dependent, respectively. Parameter  estimation techniques are developed which are applicable to both multiscaling and multiaffine fields. The scale parameter (width, σ, of the pdfs of the log-breakdown coefficients is a measure of the intermittency of a field. For multiaffine fields, this scale parameter is found to increase with scale in a power-law fashion consistent with a bounded-cascade picture of rainfall modelling. The resulting power-law exponent, H, is indicative of the smoothness of the field. Some details of breakdown coefficient analysis are addressed and a theoretical link between this analysis and moment scaling analysis is also presented. Breakdown coefficient properties of cascades are also investigated in the context of parameter estimation for modelling purposes.

Estimation of uranium and cobalt-60 distribution coefficients and uranium-235 enrichment at the Combustion Engineering Company site in Windsor, Connecticut

International Nuclear Information System (INIS)

Wang, Y.; Orlandini, K.A.; Yu, C.

1996-05-01

Site-specific distribution coefficients for uranium isotopes and cobalt-60 (Co-60) and the fraction of uranium-235 (U-235) enrichment by mass were estimated for environmental samples collected from the Combustion Engineering Company site in Windsor, CT. This site has been identified for remedial action under the US Department of Energy's (DOE) Formerly Utilized Sites Remedial Action Program. The authority of DOE at the Combustion Engineering site is limited to (1) Building 3; (2) other activities or areas associated exclusively with Building 3 (such as sewer lines); or (3) contamination that is exclusively highly enriched uranium. In this study, 16 samples were collected from the Combustion Engineering site, including 8 soil, 4 sediment, 3 water, and 1 water plus sludge sample. These samples were analyzed for isotopic uranium by alpha spectrometry and for Co-60 by gamma spectrometry. The site-specific distribution coefficient for each isotope was estimated as the ratio of extractable radionuclide activity in the solid phase to the activity in the contact solution following a 19-day equilibration. The uranium activity measurements indicate that uranium-234 (U-234) and uranium-238 (U-238) were in secular equilibrium in two soil samples and that soil and sediment samples collected from other sampling locations had higher U-234 activity than U-238 activity in both the solid and solution phases. The site-specific distribution coefficient (Kd) ranged from 82 to 44,600 mL/g for U-238 and from 102 to 65,900 mL/g for U-234. Calculation of U-235 enrichment by mass indicated that four soil samples had values greater than 0.20; these values were 0.37, 0.38, 0.46, and 0.68. Cobalt-60 activity was detected in only three sediment samples. The measured Co-60 activity in the solid phase ranged from 0.15 to 0.45 pCi/g and that in the water phase of all three samples combined was 4 pCi/L. The Kd value for Co-60 in the site brook sediment was calculated to be 70 mL/g

Sorption-desorption processes of radioisotopes with solid materials from liquid releases and atmosphere deposits. The distribution coefficient (Ksub(d)), its uses, limitations, and practical applications

International Nuclear Information System (INIS)

Saas, Arsene

1979-03-01

The various sorption-desorption processes of radionuclides with environmental materials are presented. The parameters governing the distribution coefficient are reviewed in the light of various examples. The factors affecting equilibria between the different phases are: reaction time, concentration of the solid phase, water quality, salinity, competition between ions, concentration of radioisotopes or stable isotopes, pH of the mobile phase, particle diameter, chemical form of the radioisotopes, nature of the solid phase, temperature. The effects of the biological parameters on the distribution coefficient are discussed. Biological processes affect the main chemical transformations: mineralization, insolubilization, oxidation-reduction, complexation, ... The importance of these processes is demonstrated by a number of examples in various media. Finally, the practical use of Ksub(d) in the assessment of the environmental impact of radioactive releases is developed, with special emphasis on the limits of its use in siting studies and its essential interest in specifying pathways and capacity of a river system [fr

New method for calculating the coupling coefficient in graded index optical fibers

Science.gov (United States)

Savović, Svetislav; Djordjevich, Alexandar

2018-05-01

A simple method is proposed for determining the mode coupling coefficient D in graded index multimode optical fibers. It only requires observation of the output modal power distribution P(m, z) for one fiber length z as the Gaussian launching modal power distribution changes, with the Gaussian input light distribution centered along the graded index optical fiber axis (θ0 = 0) without radial offset (r0 = 0). A similar method we previously proposed for calculating the coupling coefficient D in a step-index multimode optical fibers where the output angular power distributions P(θ, z) for one fiber length z with the Gaussian input light distribution launched centrally along the step-index optical fiber axis (θ0 = 0) is needed to be known.

Determination of the distribution coefficient of 46 elements on tin dioxide in 0.1N HNO3-acetone media

International Nuclear Information System (INIS)

Jaffrezic-Renault, N.

1977-01-01

The use of radioactive indicators for the determination of the distribution coefficients of 46 elements on SnO 2 in 0.1N HNO 3 -acetone media is described. The determination has been carried out in static conditions: labelled element solution has been agitated with SnO 2 for two hours; the elements have been labelled with radioisotopes generally obtained by (n, γ) reaction, by irradiating a part of the used salt in EL 3 or OSIRIS reactor in the C.E.N. Saclay (France). Results show that the elements may be classified into several groups, according to their oxidation state. (T.I.)

FGF21 is not required for glucose homeostasis, ketosis or tumour suppression associated with ketogenic diets in mice.

Science.gov (United States)

Stemmer, Kerstin; Zani, Fabio; Habegger, Kirk M; Neff, Christina; Kotzbeck, Petra; Bauer, Michaela; Yalamanchilli, Suma; Azad, Ali; Lehti, Maarit; Martins, Paulo J F; Müller, Timo D; Pfluger, Paul T; Seeley, Randy J

2015-10-01

Ketogenic diets (KDs) have increasingly gained attention as effective means for weight loss and potential adjunctive treatment of cancer. The metabolic benefits of KDs are regularly ascribed to enhanced hepatic secretion of fibroblast growth factor 21 (FGF21) and its systemic effects on fatty-acid oxidation, energy expenditure (EE) and body weight. Ambiguous data from Fgf21-knockout animal strains and low FGF21 concentrations reported in humans with ketosis have nevertheless cast doubt regarding the endogenous function of FGF21. We here aimed to elucidate the causal role of FGF21 in mediating the therapeutic benefits of KDs on metabolism and cancer. We established a dietary model of increased vs decreased FGF21 by feeding C57BL/6J mice with KDs, either depleted of protein or enriched with protein. We furthermore used wild-type and Fgf21-knockout mice that were subjected to the respective diets, and monitored energy and glucose homeostasis as well as tumour growth after transplantation of Lewis lung carcinoma cells. Hepatic and circulating, but not adipose tissue, FGF21 levels were profoundly increased by protein starvation, independent of the state of ketosis. We demonstrate that endogenous FGF21 is not essential for the maintenance of normoglycaemia upon protein and carbohydrate starvation and is therefore not needed for the effects of KDs on EE. Furthermore, the tumour-suppressing effects of KDs were independent of FGF21 and, rather, driven by concomitant protein and carbohydrate starvation. Our data indicate that the multiple systemic effects of KD exposure in mice, previously ascribed to increased FGF21 secretion, are rather a consequence of protein malnutrition.

Modelling of power-reactivity coefficient measurement

International Nuclear Information System (INIS)

Strmensky, C.; Petenyi, V.; Jagrik, J.; Minarcin, M.; Hascik, R.; Toth, L.

2005-01-01

Report describes results of modeling of power-reactivity coefficient analysis on power-level. In paper we calculate values of discrepancies arisen during transient process. These discrepancies can be arisen as result of experiment evaluation and can be caused by disregard of 3D effects on neutron distribution. The results are critically discussed (Authors)

measurements of distribution coefficients and lipophilicity values

African Journals Online (AJOL)

Preferred Customer

octanol and water, followed by measuring the distribution of the solute in ... Instrumentation and apparatus: HPLC-UV-DAD and HPLC–ESI-MS experiments .... process in the determination of KD and log P values for the HFSLM extracts. ..... Perrin, D.D.; Dempsey, B. Buffers for pH and Metal Ion Control, Chapman and Hall:.

Measuring Resource Inequality: The Gini Coefficient

Directory of Open Access Journals (Sweden)

Michael T. Catalano

2009-07-01

Full Text Available This paper stems from work done by the authors at the Mathematics for Social Justice Workshop held in June of 2007 at Middlebury College. We provide a description of the Gini coefficient and some discussion of how it can be used to promote quantitative literacy skills in mathematics courses. The Gini Coefficient was introduced in 1921 by Italian statistician Corrado Gini as a measure of inequality. It is defined as twice the area between two curves. One, the Lorenz curve for a given population with respect to a given resource, represents the cumulative percentage of the resource as a function of the cumulative percentage of the population that shares that percentage of the resource. The second curve is the line y = x which is the Lorenz curve for a population which shares the resource equally. The Gini coefficient can be interpreted as the percentage of inequality represented in the population with respect to the given resource. We propose that the Gini coefficient can be used to enhance students’ understanding of calculus concepts and provide practice for students in using both calculus and quantitative literacy skills. Our examples are based mainly on distribution of energy resources using publicly available data from the Energy Information Agency of the United States Government. For energy resources within the United States, we find that by household, the Gini coefficient is 0.346, while using the 51 data points represented by the states and Washington D.C., the Gini coefficient is 0.158. When we consider the countries of the world as a population of 210, the Gini coefficient is 0.670. We close with ideas for questions which can be posed to students and discussion of the experiences two other mathematics instructors have had incorporating the Gini coefficient into pre-calculus-level mathematics classes.

Self-diffusion coefficients of the metastable Lennard-Jones vapor

International Nuclear Information System (INIS)

Nie Chu; Zhou Youhua; Marlow, W H; Hassan, Y A

2008-01-01

Self-diffusion coefficients of a metastable Lennard-Jones vapor were obtained using the memory function formalism and the frequency moments of the velocity autocorrelation function at reduced temperatures from 0.75 to 1.0. The radial density distribution functions used to evaluate the second, fourth and sixth frequency moments of the velocity autocorrelation function were obtained from the restricted canonical ensemble Monte Carlo simulation (Corti and Debenedetti 1994 Chem. Eng. Sci. 49 2717). The self-diffusion coefficients at reduced temperature 0.75 do not vary monotonically as the density increases, and for the other three temperatures the self-diffusion coefficients vary normally

Self-diffusion coefficients of the metastable Lennard-Jones vapor

Energy Technology Data Exchange (ETDEWEB)

Nie Chu; Zhou Youhua [School of Physics and Information Engineering, Jianghan University, Wuhan 430056 (China); Marlow, W H; Hassan, Y A [Department of Nuclear Engineering, Texas A and M University, College Station, TX 77843 (United States)], E-mail: yhzhou@jhun.edu.cn

2008-10-15

Self-diffusion coefficients of a metastable Lennard-Jones vapor were obtained using the memory function formalism and the frequency moments of the velocity autocorrelation function at reduced temperatures from 0.75 to 1.0. The radial density distribution functions used to evaluate the second, fourth and sixth frequency moments of the velocity autocorrelation function were obtained from the restricted canonical ensemble Monte Carlo simulation (Corti and Debenedetti 1994 Chem. Eng. Sci. 49 2717). The self-diffusion coefficients at reduced temperature 0.75 do not vary monotonically as the density increases, and for the other three temperatures the self-diffusion coefficients vary normally.

Relationship between attenuation coefficients and dose-spread kernels

International Nuclear Information System (INIS)

Boyer, A.L.

1988-01-01

Dose-spread kernels can be used to calculate the dose distribution in a photon beam by convolving the kernel with the primary fluence distribution. The theoretical relationships between various types and components of dose-spread kernels relative to photon attenuation coefficients are explored. These relations can be valuable as checks on the conservation of energy by dose-spread kernels calculated by analytic or Monte Carlo methods

The determination of the cesium distribution coefficient of the interim storage soil from Abadia de Goias, Go, Brazil

International Nuclear Information System (INIS)

Marumo, J.T.; Suarez, A.A.

1989-01-01

In September, 1987, an unauthorized removal of a cesium-therapy unit and its violation caused an accident, where several places of Goiania's city, capital of Goias, Brazil, were contaminated. The removal of the radioactive wastes generated from decontamination process, was made to Abadia de Goias city (near Goiania), where an interim storage was constructed. Soil samples collected from the 57th Street (Goiania) and from the interim storage permitted to determine, through static method, the cesium distribution coefficient for different cesium solution concentrations. Those results allows for some migration/retention evaluations in disposal site selection. Some soils parameters (water content, density, granulometric analysis, etc) as well as clay minerals constituents were also determined. (author) [pt

Robust Exponential Synchronization for a Class of Master-Slave Distributed Parameter Systems with Spatially Variable Coefficients and Nonlinear Perturbation

Directory of Open Access Journals (Sweden)

Chengdong Yang

2015-01-01

Full Text Available This paper addresses the exponential synchronization problem of a class of master-slave distributed parameter systems (DPSs with spatially variable coefficients and spatiotemporally variable nonlinear perturbation, modeled by a couple of semilinear parabolic partial differential equations (PDEs. With a locally Lipschitz constraint, the perturbation is a continuous function of time, space, and system state. Firstly, a sufficient condition for the robust exponential synchronization of the unforced semilinear master-slave PDE systems is investigated for all admissible nonlinear perturbations. Secondly, a robust distributed proportional-spatial derivative (P-sD state feedback controller is desired such that the closed-loop master-slave PDE systems achieve exponential synchronization. Using Lyapunov’s direct method and the technique of integration by parts, the main results of this paper are presented in terms of spatial differential linear matrix inequalities (SDLMIs. Finally, two numerical examples are provided to show the effectiveness of the proposed methods applied to the robust exponential synchronization problem of master-slave PDE systems with nonlinear perturbation.

Tomography based determination of permeability, Dupuit-Forchheimer coefficient, and interfacial heat transfer coefficient in reticulate porous ceramics

International Nuclear Information System (INIS)

Petrasch, Joerg; Meier, Fabian; Friess, Hansmartin; Steinfeld, Aldo

2008-01-01

A computer tomography based methodology is applied to determine the transport properties of fluid flow across porous media. A 3D digital representation of a 10-ppi reticulate porous ceramic (RPC) sample was generated by X-ray tomographic scans. Structural properties such as the porosity, specific interfacial surface area, pore-size distribution, mean survival time, two-point correlation function s 2 , and local geometry distribution of the RPC sample are directly extracted from the tomographic data. Reference solutions of the fluid flow governing equations are obtained for Re = 0.2-200 by applying finite volume direct pore-level numerical simulation (DPLS) using unstructured, body-fitted, tetrahedral mesh discretization. The permeability and the Dupuit-Forchheimer coefficient are determined from the reference solutions by DPLS, and compared to the values predicted by selected porous media flow models, namely: conduit-flow, hydraulic radius theory, drag models, mean survival time bound, s 2 -bound, fibrous bed correlations, and local porosity theory-based models. DPLS is further employed to determine the interfacial heat transfer coefficient and to derive a corresponding Nu-correlation, which is compared to empirical correlations

Gini coefficient as a life table function

Directory of Open Access Journals (Sweden)

2003-06-01

Full Text Available This paper presents a toolkit for measuring and analyzing inter-individual inequality in length of life by Gini coefficient. Gini coefficient and four other inequality measures are defined on the length-of-life distribution. Properties of these measures and their empirical testing on mortality data suggest a possibility for different judgements about the direction of changes in the degree of inequality by using different measures. A new computational procedure for the estimation of Gini coefficient from life tables is developed and tested on about four hundred real life tables. The estimates of Gini coefficient are precise enough even for abridged life tables with the final age group of 85+. New formulae have been developed for the decomposition of differences between Gini coefficients by age and cause of death. A new method for decomposition of age-components into effects of mortality and composition of population by group is developed. Temporal changes in the effects of elimination of causes of death on Gini coefficient are analyzed. Numerous empirical examples show: Lorenz curves for Sweden, Russia and Bangladesh in 1995, proportional changes in Gini coefficient and four other measures of inequality for the USA in 1950-1995 and for Russia in 1959-2000. Further shown are errors of estimates of Gini coefficient when computed from various types of mortality data of France, Japan, Sweden and the USA in 1900-95, decompositions of the USA-UK difference in life expectancies and Gini coefficients by age and cause of death in 1997. As well, effects of elimination of major causes of death in the UK in 1951-96 on Gini coefficient, age-specific effects of mortality and educational composition of the Russian population on changes in life expectancy and Gini coefficient between 1979 and 1989. Illustrated as well are variations in life expectancy and Gini coefficient across 32 countries in 1996-1999 and associated changes in life expectancy and Gini

Modal and Dynamic Analysis of a Vehicle with Kinetic Dynamic Suspension System

Directory of Open Access Journals (Sweden)

Bangji Zhang

2016-01-01

Full Text Available A novel kinetic dynamic suspension (KDS system is presented for the cooperative control of the roll and warp motion modes of off-road vehicles. The proposed KDS system consists of two hydraulic cylinders acting on the antiroll bars. Hence, the antiroll bars are not completely replaced by the hydraulic system, but both systems are installed. In this paper, the vibration analysis in terms of natural frequencies of different motion modes in frequency domain for an off-road vehicle equipped with different configurable suspension systems is studied by using the modal analysis method. The dynamic responses of the vehicle with different configurable suspension systems are investigated under different road excitations and maneuvers. The results of the modal and dynamic analysis prove that the KDS system can reduce the roll and articulation motions of the off-road vehicle without adding extra bounce stiffness and deteriorating the ride comfort. Furthermore, the roll stiffness is increased and the warp stiffness is decreased by the KDS system, which could significantly enhance handing performance and off-road capability.

Spectral effects on some physical coefficients of x-Ray interaction with materials of low atomic number

International Nuclear Information System (INIS)

EL-Kazzaz, S.A.; Youssef, M.; EL-Hadad, S.; and EL-Nadi, L.M.

1988-01-01

X-ray spectra were measured before and after passing through some materials of medical importance applying X-ray diffraction. The mass absorption coefficients of these materials were determined at X-ray peak voltages 27, 30 and 42 kV-p making use the measured spectrum and also by using the direct beam absorption. It has been found that the mass absorption coefficients calculated from the X-ray spectral distribution analysis are in general lower than those obtained considering the direct beam method. From the study of the atomic number and energy dependence of the mass absorption coefficients it has been found that the dependence of the coefficients calculated from the spectral distribution is good agreement with the previously studied data for monoenergetic x-ray beam. Also the roentgen - to - Rad conversion factors were determined at the different used energies and materials. The value of the mass absorption coefficients calculated from the spectral distribution is recommended for use in dose calculation

Evaluating the coefficients of autocorrelation in a series of annual run-off of the Far East rivers

Energy Technology Data Exchange (ETDEWEB)

Sakharyuk, A V

1981-01-01

An evaluation is made of the coefficients of autocorrelation in series of annual river run-off based on group analysis using data on the distribution law of sampling correlation coefficients of temporal series subordinate to the III type Pearson's distribution.

Distribution of 14 elements from two solutions simulating Hanford HLW Tank 102-SY (acid-dissolved sludge and acidified supernate) on four cation exchange resins and five anion exchange resins having different functional groups

International Nuclear Information System (INIS)

Marsh, S.F.; Svitra, Z.V.; Bowen, S.M.

1995-01-01

As part of the Tank Waste Remediation System program at Los Alamos, we evaluated a series of cation exchange and anion exchange resins for their ability to remove hazardous components from radioactive high-level waste (HLW). The anion exchangers were Reillex TM HPQ, a polyvinyl pyridine resin, and four strong-base polystyrene resins having trimethyl, tri ethyl, tri propyl, and tributyl amine as their respective functional groups. The cation exchange resins included Amberlyst TM 15 and Amberlyst tM XN-1010 with sulfonic acid functionality, Duolite TM C-467 with phosphonic acid functionality, and poly functional Diphonix TM with di phosphonic acid, sulfonic acid, and carboxylic acid functionalities. We measured the distributions of 14 elements on these resins from solutions simulating acid-dissolved sludge (pH 0.6) and acidified supernate (pH 3.5) from underground storage tank 102-SY at the Hanford Reservation near Richland, Washington, USA. To these simulants, we added the appropriate radionuclides and used gamma spectrometry to measure fission products (Ce, Cs, Sr, Tc, and Y), actinides (U, Pu, and Am), and matrix elements (Cr, Co, Fe, Mn, Zn, and Zr). For each of the 252 element/resin/solution combinations, distribution coefficients (Kds) were measured for dynamic contact periods of 30 minutes, 2 hours, and 6 hours to obtain information about sorption kinetics from these complex media. Because we measured the sorption of many different elements, the tabulated results indicate which unwanted elements are most likely to interfere with the sorption of elements of special interest. On the basis of these 756 measured Kd values, we conclude that some of the tested resins appear suitable for partitioning hazardous components from Hanford HLW. (author). 10 refs., 11 tabs

Distribution coefficients of 134Cs, 60Co, 65Zn and 51Cr in different contaminated soils affected by organic waste disposal

International Nuclear Information System (INIS)

Metwally, E.

2003-01-01

Batch adsorption experiments were conducted with mixtures of solutes of different concentrations of some radionuclides as 1 34Sc, 6 0Co, 6 5Zn and 5 1Cr, in five different soils. The soils varied in their organic matter source and content due to prolonged irrigation with primary treated sewage effluent or untreated industrial wastewater. the distribution coefficients (K d ) were measured at different equilibrium times namely, 2, 24, 48, 72, 144 and 336 h. statistical correlation and curve fittings indicated that metal sorption into soils was influenced by the presence of clays, organic matter content and hydrous oxides of Fe and Mn. The highest log K d values were obtained in case of Cs in all investigated soils with a general mean of 1.878 0.28. Log K d for Cr exhibited a higher values than those did for at any tested soil (general mean 1.675 .33 and 1.658 0.24 for Cr and Co respectively). Zinc had the lowest log K d values, indicating that Cs is highly retained in soil than other tested elements and Zn is relatively mobile in soil than other tested elements. The investigated elements retention in soil could be arranged in the following order: Cs > Cr > Co > Zn. Soils enriched in organic matter exhibited the highest sorption caption capacity for all tested metals. Variability in the distribution coefficient due to soils and metals interactions were discussed

Negative power coefficient on PHWRs with CARA fuel

International Nuclear Information System (INIS)

Lestani, H.A.; González, H.J.; Florido, P.C.

2014-01-01

Highlights: • A PHWR fuel was optimized to obtain a negative power coefficient. • Fuel cost, being a measure of design investment efficiency, was optimized. • Influence on power coefficient of geometrical and economical parameters’ was studied. • Different neutronic absorbers were studied; pure absorbers can be used. • Thermal and economical models were developed to complement neutronic assessment. - Abstract: A study of power coefficient of reactivity in heavy water reactors is made analyzing the reactivity components of fuels with several modifications oriented at reducing the coefficient. A cell model is used for neutronics calculations; a non-linear two dimensional model is used to evaluate the thermal changes that follow a power change; and a levelized unit energy cost model is used to assess the economical feasibility of the design changes introduced to reduce power coefficient. The necessity of modelling all the aforementioned quantities in a coupled scheme is stressed, as a strong interdependence was found. A series of design changes complied with a negative power coefficient of reactivity, with a feasible power radial distribution and with low refuelling cost. Some investigation lines that exceed the fuel cell study and deal with the plant operation are marked as potentially addressing the stable operation of big heavy water reactors

Determination of BEACON Coupling Coefficients using data from Xenon transient

International Nuclear Information System (INIS)

Bozic, M.; Kurincic, B.

2007-01-01

NEK uses BEACO TM code (BEACO TM - Westinghouse Best Estimate Analyzer for Core Operating Nuclear) for core monitoring, analysis and core behaviour prediction. Coupling Coefficients determine relationship between core response and excore instrumentation. Measured power distribution using incore moveable detectors during Xenon transient with sufficient power axial offset change is the most important data for further analysis. Classic methodology and BEACO TM Conservative methodology using established Coupling Coefficients are compared on NPP Krsko case. BEACON TM Conservative methodology with predefined Coupling Coefficients is used as a surveillance tool for verification of relationship between core and excore instrumentation during power operation. (author)

Sources, distribution and export coefficient of phosphorus in lowland polders of Lake Taihu Basin, China.

Science.gov (United States)

Huang, Jiacong; Gao, Junfeng; Jiang, Yong; Yin, Hongbin; Amiri, Bahman Jabbarian

2017-12-01

Identifying phosphorus (P) sources, distribution and export from lowland polders is important for P pollution management, however, is challenging due to the high complexity of hydrological and P transport processes in lowland areas. In this study, the spatial pattern and temporal dynamics of P export coefficient (PEC) from all the 2539 polders in Lake Taihu Basin, China were estimated using a coupled P model for describing P dynamics in a polder system. The estimated amount of P export from polders in Lake Taihu Basin during 2013 was 1916.2 t/yr, with a spatially-averaged PEC of 1.8 kg/ha/yr. PEC had peak values (more than 4.0 kg/ha/yr) in the polders near/within the large cities, and was high during the rice-cropping season. Sensitivity analysis based on the coupled P model revealed that the sensitive factors controlling the PEC varied spatially and changed through time. Precipitation and air temperature were the most sensitive factors controlling PEC. Culvert controlling and fertilization were sensitive factors controlling PEC during some periods. This study demonstrated an estimation of PEC from 2539 polders in Lake Taihu Basin, and an identification of sensitive environmental factors affecting PEC. The investigation of polder P export in a watershed scale is helpful for water managers to learn the distribution of P sources, to identify key P sources, and thus to achieve best management practice in controlling P export from lowland areas. Copyright © 2017 Elsevier Ltd. All rights reserved.

Experimental evaluation of heat transfer coefficients between radiant ceiling and room

DEFF Research Database (Denmark)

Causone, Francesco; Corgnati, Stefano P.; Filippi, Marco

2009-01-01

The heat transfer coefficients between radiant surfaces and room are influenced by several parameters: surfaces temperature distributions, internal gains, air movements. The aim of this paper is to evaluate the heat transfer coefficients between radiant ceiling and room in typical conditions...... of occupancy of an office or residential building. Internal gains were therefore simulated using heated cylinders and heat losses using cooled surfaces. Evaluations were developed by means of experimental tests in an environmental chamber. Heat transfer coefficient may be expressed separately for radiation...

Measurement method of the distribution coefficient on the sorption process. Basic procedure of the method relevant to the barrier materials used for the deep geological disposal: 2006

International Nuclear Information System (INIS)

2006-08-01

This standard was approved by Atomic Energy Society of Japan after deliberation of the Subcommittee on the Radioactive Waste Management, the Nuclear Cycle Technical Committee and the Standard Committee, and after obtaining about 600 comments from specialists of about 30 persons. This document defines the basic measurement procedure of the distribution coefficient (hereafter referred as Kd) to judge the reliability, reproducibility and applications and to provide the requirements for inter-comparison of Kd for a variety of barrier materials used for deep geological disposal of radioactive wastes. The basic measurement procedure of Kd is standardized, following the preceded standard, 'Measurement Method of the Distribution Coefficient on the Sorption Process - Basic Procedure of Batch Method Relevant to the Barrier Materials Used for the Shallow Land Disposal: 2002 (hereafter referred as Standard for the Shallow Land Disposal)', and considering recent progress after its publication and specific issues to the deep geological disposal. (J.P.N.)

The coefficient of determination R2 and intra-class correlation coefficient from generalized linear mixed-effects models revisited and expanded.

Science.gov (United States)

Nakagawa, Shinichi; Johnson, Paul C D; Schielzeth, Holger

2017-09-01

The coefficient of determination R 2 quantifies the proportion of variance explained by a statistical model and is an important summary statistic of biological interest. However, estimating R 2 for generalized linear mixed models (GLMMs) remains challenging. We have previously introduced a version of R 2 that we called [Formula: see text] for Poisson and binomial GLMMs, but not for other distributional families. Similarly, we earlier discussed how to estimate intra-class correlation coefficients (ICCs) using Poisson and binomial GLMMs. In this paper, we generalize our methods to all other non-Gaussian distributions, in particular to negative binomial and gamma distributions that are commonly used for modelling biological data. While expanding our approach, we highlight two useful concepts for biologists, Jensen's inequality and the delta method, both of which help us in understanding the properties of GLMMs. Jensen's inequality has important implications for biologically meaningful interpretation of GLMMs, whereas the delta method allows a general derivation of variance associated with non-Gaussian distributions. We also discuss some special considerations for binomial GLMMs with binary or proportion data. We illustrate the implementation of our extension by worked examples from the field of ecology and evolution in the R environment. However, our method can be used across disciplines and regardless of statistical environments. © 2017 The Author(s).

Varying coefficients model with measurement error.

Science.gov (United States)

Li, Liang; Greene, Tom

2008-06-01

We propose a semiparametric partially varying coefficient model to study the relationship between serum creatinine concentration and the glomerular filtration rate (GFR) among kidney donors and patients with chronic kidney disease. A regression model is used to relate serum creatinine to GFR and demographic factors in which coefficient of GFR is expressed as a function of age to allow its effect to be age dependent. GFR measurements obtained from the clearance of a radioactively labeled isotope are assumed to be a surrogate for the true GFR, with the relationship between measured and true GFR expressed using an additive error model. We use locally corrected score equations to estimate parameters and coefficient functions, and propose an expected generalized cross-validation (EGCV) method to select the kernel bandwidth. The performance of the proposed methods, which avoid distributional assumptions on the true GFR and residuals, is investigated by simulation. Accounting for measurement error using the proposed model reduced apparent inconsistencies in the relationship between serum creatinine and GFR among different clinical data sets derived from kidney donor and chronic kidney disease source populations.

Variable Eddington factors and flux-limiting diffusion coefficients

International Nuclear Information System (INIS)

Whalen, P.P.

1982-01-01

Variable Eddington factors and flux limiting diffusion coefficients arise in two common techniques of closing the moment equations of transport. The first two moment equations of the full transport equation are still frequently used to solve many problems of radiative or particle transport. An approximate analysis, developed by Levermore, exhibits the relation between the coefficients of the two different techniques. This analysis is described and then used to test the validity of several commonly used flux limiters and Eddington factors. All of the ad-hoc flux limiters have limited validity. All of the variable Eddington factors derived from some underlying description of the angular distribution function are generally valid. The use of coefficients from Minerbo's elegant maximum entropy Eddington factor analysis is suggested for use in either flux limited diffusion or variable Eddington factor equations

Angular distribution coefficients for γ-ray polarization produced in polarized capture reactions

International Nuclear Information System (INIS)

Wulf, E.A.; Guillemette, J.; Weller, H.R.; Seyler, R.G.

1999-01-01

The previous publications have dealt with the angular momentum formalism of both linear and circularly polarized photons in (γ, x) reactions on both polarized and unpolarized targets, and the inverse (capture) reactions initiated by polarized beams. In the present work, utilizing the general formalism of Welton, the authors deal with the linear polarization of the γ-rays which are produced in capture reactions on unpolarized targets, including the possibility of having incident polarized spin 1/2 projectiles. These capture reactions are denoted by a(rvec x, rvec L)c, where rvec x is the incident polarized spin 1/2 projectile and rvec L represents the outgoing polarized γ-ray. They present here the formalism in a convenient form, display a sample table of coefficients, and illustrate its use by means of several examples. A FORTRAN code will be made available for generating similar coefficients for other reactions

Ångström coefficient as a tracer of the continental aerosols

NARCIS (Netherlands)

Kuśmierczyk-Michulec, J.T.; Eijk, A.M.J. van

2007-01-01

The variation of the extinction coefficient with wavelength can be presented as a power law function with a constant (related to the power factor) known as the Ångström coefficient. When the particle size distribution is dominated by small particles, usually associated with pollution, the Ångström

Octanol-water distribution of engineered nanomaterials.

Science.gov (United States)

Hristovski, Kiril D; Westerhoff, Paul K; Posner, Jonathan D

2011-01-01

The goal of this study was to examine the effects of pH and ionic strength on octanol-water distribution of five model engineered nanomaterials. Distribution experiments resulted in a spectrum of three broadly classified scenarios: distribution in the aqueous phase, distribution in the octanol, and distribution into the octanol-water interface. Two distribution coefficients were derived to describe the distribution of nanoparticles among octanol, water and their interface. The results show that particle surface charge, surface functionalization, and composition, as well as the solvent ionic strength and presence of natural organic matter, dramatically impact this distribution. Distributions of nanoparticles into the interface were significant for nanomaterials that exhibit low surface charge in natural pH ranges. Increased ionic strengths also contributed to increased distributions of nanoparticle into the interface. Similarly to the octanol-water distribution coefficients, which represent a starting point in predicting the environmental fate, bioavailability and transport of organic pollutants, distribution coefficients such as the ones described in this study could help to easily predict the fate, bioavailability, and transport of engineered nanomaterials in the environment.

Statistical Analysis of Bending Rigidity Coefficient Determined Using Fluorescence-Based Flicker-Noise Spectroscopy.

Science.gov (United States)

Doskocz, Joanna; Drabik, Dominik; Chodaczek, Grzegorz; Przybyło, Magdalena; Langner, Marek

2018-06-01

Bending rigidity coefficient describes propensity of a lipid bilayer to deform. In order to measure the parameter experimentally using flickering noise spectroscopy, the microscopic imaging is required, which necessitates the application of giant unilamellar vesicles (GUV) lipid bilayer model. The major difficulty associated with the application of the model is the statistical character of GUV population with respect to their size and the homogeneity of lipid bilayer composition, if a mixture of lipids is used. In the paper, the bending rigidity coefficient was measured using the fluorescence-enhanced flicker-noise spectroscopy. In the paper, the bending rigidity coefficient was determined for large populations of 1-palmitoyl-2-oleoyl-sn-glycero-3-phosphocholine and 1,2-dioleoyl-sn-glycero-3-phosphocholine vesicles. The quantity of obtained experimental data allows to perform statistical analysis aiming at the identification of the distribution, which is the most appropriate for the calculation of the value of the membrane bending rigidity coefficient. It has been demonstrated that the bending rigidity coefficient is characterized by an asymmetrical distribution, which is well approximated with the gamma distribution. Since there are no biophysical reasons for that we propose to use the difference between normal and gamma fits as a measure of the homogeneity of vesicle population. In addition, the effect of a fluorescent label and types of instrumental setups on determined values has been tested. Obtained results show that the value of the bending rigidity coefficient does not depend on the type of a fluorescent label nor on the type of microscope used.

Radar meteors range distribution model. IV. Ionization coefficient

Czech Academy of Sciences Publication Activity Database

Pecinová, Drahomíra; Pecina, Petr

2008-01-01

Roč. 38, č. 1 (2008), s. 12-20 ISSN 1335-1842 R&D Projects: GA ČR GA205/03/1405 Institutional research plan: CEZ:AV0Z10030501 Keywords : physics of meteors * radar meteors * range distribution Subject RIV: BN - Astronomy, Celestial Mechanics, Astrophysics

Distribution coefficients for Pb+2 and Cr+6 with variation in soil particle size

International Nuclear Information System (INIS)

Singhal, R.K.; Preetha, J.; Gurg, R.P.

2003-01-01

Simulated experiments were conducted in the laboratory to evaluate the impact of soil particle size on the distribution coefficient (K d ) for soil - water system for Pb as Pb +2 and Cr as Cr +6 . The variation in particle size leads to variation in mineralogical and organic carbon (OC) contents which in turn lead to variation in cation exchange capacity (CEC). The conditions were kept as close to that of the natural environment during the spiking of the soil. The spiked soil is fractionated in seven different fractions between 500 - 355 μm and 105 - > 75 μm contains relatively higher percentage of OC than the other fractions. The CEC of different fractions of the soil is determined by ammonium acetate method. Higher CEC was observed for particle in the range of 105 - > 75 μm. The analysis of Pb and Cr was carried out using Atomic Absorption Spectrometer after the complete destruction f the soil matrix. Among the various fractions, the K d values are higher for 75μm for Pb +2 and Cr +6 and their ranges are 4.3-9.6 x 10 5 ml/gm and 2.1-24.8 x 10 6 ml/gm, respectively. (author)

Performance Assessment Transport Modeling of Uranium at the Area 5 Radioactive Waste Management Site at the Nevada National Security Site

International Nuclear Information System (INIS)

2010-01-01

Following is a brief summary of the assumptions that are pertinent to the radioactive isotope transport in the GoldSim Performance Assessment model of the Area 5 Radioactive Waste Management Site, with special emphasis on the water-phase reactive transport of uranium, which includes depleted uranium products. The Area 5 PA model assumes activity disposed in trenches is well mixed within the native alluvium of the trench at the time the facility is closed. Waste containers and waste forms are assumed not to limit the release of radionuclides for transport. In the Area 5 RWMS PA model, the pathways that are considered to bring radioactivity in the waste zone to the surface soils of the closure covers are (1) plant uptake, (2) burrowing animal activity, and (3) advection/dispersion/diffusion in the pore water. Water-phase transport is a minor component of the transport, which is dominated by plant uptake and burrowing animal activity. Because the soil column is mostly dry, upward water flux rates are extremely small, resulting in small advective/dispersive transport of radioactive isotopes in pore water of the unsaturated zone. Reactive transport of radioactive elements in the Area 5 soil pore water are modeled using element-specific partition coefficients (Kds) that partition radioactivity between pore water and soil of the disposal cell, and solubility limits that control the solubility of elements in pore water. Geochemical modeling is not performed in the Area 5 RWMS GoldSim PA model; however, Kds and solubility limits were derived from previous geochemical modeling performed using Area 5 geochemical data. Kds for uranium were developed based on geochemical modeling using the mineral characteristics of soil (alluvium) and the chemical characteristics of water at the site (Carle et al., 2002). In the GoldSim model, uranium Kd is represented with a lognormal distribution with a mean value of 0.8 milliliter per gram (taken from Figure 4.11, Page 4-19 of Carle et al

Comparison of values of Pearson’s and Spearman’s correlation coefficient on the same sets of data

OpenAIRE

Hauke, Jan; Kossowski, Tomasz

2011-01-01

Spearman’s rank correlation coefficient is a nonparametric (distribution-free) rank statistic proposed by Charles Spearman as a measure of the strength of an association between two variables. It is a measure of a monotone association that is used when the distribution of data makes Pearson’s correlation coefficient undesirable or misleading. Spearman’s coefficient is not a measure of the linear relationship between two variables, as some “statisticians” declare. It assesses how well an arbit...

Electron Transport Coefficients and Effective Ionization Coefficients in SF6-O2 and SF6-Air Mixtures Using Boltzmann Analysis

Science.gov (United States)

Wei, Linsheng; Xu, Min; Yuan, Dingkun; Zhang, Yafang; Hu, Zhaoji; Tan, Zhihong

2014-10-01

The electron drift velocity, electron energy distribution function (EEDF), density-normalized effective ionization coefficient and density-normalized longitudinal diffusion velocity are calculated in SF6-O2 and SF6-Air mixtures. The experimental results from a pulsed Townsend discharge are plotted for comparison with the numerical results. The reduced field strength varies from 40 Td to 500 Td (1 Townsend=10-17 V·cm2) and the SF6 concentration ranges from 10% to 100%. A Boltzmann equation associated with the two-term spherical harmonic expansion approximation is utilized to gain the swarm parameters in steady-state Townsend. Results show that the accuracy of the Boltzmann solution with a two-term expansion in calculating the electron drift velocity, electron energy distribution function, and density-normalized effective ionization coefficient is acceptable. The effective ionization coefficient presents a distinct relationship with the SF6 content in the mixtures. Moreover, the E/Ncr values in SF6-Air mixtures are higher than those in SF6-O2 mixtures and the calculated value E/Ncr in SF6-O2 and SF6-Air mixtures is lower than the measured value in SF6-N2. Parametric studies conducted on these parameters using the Boltzmann analysis offer substantial insight into the plasma physics, as well as a basis to explore the ozone generation process.

Spatial correlation in 3D MIMO channels using fourier coefficients of power spectrums

KAUST Repository

Nadeem, Qurrat-Ul-Ain; Kammoun, Abla; Debbah, Mé rouane; Alouini, Mohamed-Slim

2015-01-01

for arbitrary angular distributions and antenna patterns. The resulting expression depends on the underlying angular distributions and antenna patterns through the Fourier Series (FS) coefficients of power azimuth and elevation spectrums. The novelty

Maximal planar networks with large clustering coefficient and power-law degree distribution

International Nuclear Information System (INIS)

Zhou Tao; Yan Gang; Wang Binghong

2005-01-01

In this article, we propose a simple rule that generates scale-free networks with very large clustering coefficient and very small average distance. These networks are called random Apollonian networks (RANs) as they can be considered as a variation of Apollonian networks. We obtain the analytic results of power-law exponent γ=3 and clustering coefficient C=(46/3)-36 ln (3/2)≅0.74, which agree with the simulation results very well. We prove that the increasing tendency of average distance of RANs is a little slower than the logarithm of the number of nodes in RANs. Since most real-life networks are both scale-free and small-world networks, RANs may perform well in mimicking the reality. The RANs possess hierarchical structure as C(k)∼k -1 that are in accord with the observations of many real-life networks. In addition, we prove that RANs are maximal planar networks, which are of particular practicability for layout of printed circuits and so on. The percolation and epidemic spreading process are also studied and the comparisons between RANs and Barabasi-Albert (BA) as well as Newman-Watts (NW) networks are shown. We find that, when the network order N (the total number of nodes) is relatively small (as N∼10 4 ), the performance of RANs under intentional attack is not sensitive to N, while that of BA networks is much affected by N. And the diseases spread slower in RANs than BA networks in the early stage of the suseptible-infected process, indicating that the large clustering coefficient may slow the spreading velocity, especially in the outbreaks

Drag coefficient Variability and Thermospheric models

Science.gov (United States)

Moe, Kenneth

Satellite drag coefficients depend upon a variety of factors: The shape of the satellite, its altitude, the eccentricity of its orbit, the temperature and mean molecular mass of the ambient atmosphere, and the time in the sunspot cycle. At altitudes where the mean free path of the atmospheric molecules is large compared to the dimensions of the satellite, the drag coefficients can be determined from the theory of free-molecule flow. The dependence on altitude is caused by the concentration of atomic oxygen which plays an important role by its ability to adsorb on the satellite surface and thereby affect the energy loss of molecules striking the surface. The eccentricity of the orbit determines the satellite velocity at perigee, and therefore the energy of the incident molecules relative to the energy of adsorption of atomic oxygen atoms on the surface. The temperature of the ambient atmosphere determines the extent to which the random thermal motion of the molecules influences the momentum transfer to the satellite. The time in the sunspot cycle affects the ambient temperature as well as the concentration of atomic oxygen at a particular altitude. Tables and graphs will be used to illustrate the variability of drag coefficients. Before there were any measurements of gas-surface interactions in orbit, Izakov and Cook independently made an excellent estimate that the drag coefficient of satellites of compact shape would be 2.2. That numerical value, independent of altitude, was used by Jacchia to construct his model from the early measurements of satellite drag. Consequently, there is an altitude dependent bias in the model. From the sparce orbital experiments that have been done, we know that the molecules which strike satellite surfaces rebound in a diffuse angular distribution with an energy loss given by the energy accommodation coefficient. As more evidence accumulates on the energy loss, more realistic drag coefficients are being calculated. These improved drag

Distribution coefficients of caesium, chlorine, iodine, niobium, selenium and technetium on Olkiluoto soils

International Nuclear Information System (INIS)

Soederlund, M.; Lusa, M.; Virtanen, S.; Vaelimaa, I.; Hakanen, M.; Lehto, J.; Lahdenperae, A.-M.

2014-02-01

Retention of caesium, chlorine, iodine, niobium, selenium and technetium was investigated on soil samples from Olkiluoto using laboratory batch sorption experiments. Distribution coefficients were measured for both dried and sieved and untreated (wet, not sieved) mineral soil and humus in aerobic and anaerobic conditions. Mineralogical composition of the samples was determined by XRD-analysis. Caesium was sorbed efficiently on mineral soil samples and less efficiently on humus. Sorption decreased with decreasing cation exchange capacity and clay fraction content. The effect of competing cations decreased in the order Cs + >NH 4 + >K + >Ca 2+ >Na + . Chlorine was not retained by mineral soil samples, and the sorption was weak on humus. The sorption of iodine was the strongest on humus and the weakest on the untreated mineral soil samples in the anaerobic conditions. In the mineral soil samples, the sorption decreased with decreasing organic matter content and increasing pH. The retention of niobium on soil samples was the most efficient among the studied elements. The retention was high regardless of the aeration conditions. Sorption on humus was smaller. Selenium was retained efficiently on humus. Sorption on mineral soil samples was stronger in aerobic conditions. Sorption increased with time. Technetium was sorbed well on humus and anaerobic, untreated mineral soil samples. Sorption increased with increasing organic matter content and decreasing redox potential. The results from the sorption experiments are used in the site specific radionuclide migration modelling. (orig.)

Efficient calculation of atomic rate coefficients in dense plasmas

Science.gov (United States)

Aslanyan, Valentin; Tallents, Greg J.

2017-03-01

Modelling electron statistics in a cold, dense plasma by the Fermi-Dirac distribution leads to complications in the calculations of atomic rate coefficients. The Pauli exclusion principle slows down the rate of collisions as electrons must find unoccupied quantum states and adds a further computational cost. Methods to calculate these coefficients by direct numerical integration with a high degree of parallelism are presented. This degree of optimization allows the effects of degeneracy to be incorporated into a time-dependent collisional-radiative model. Example results from such a model are presented.

Determination of sedimentation rates and absorption coefficient of ...

African Journals Online (AJOL)

DR. MIKE HORSFALL

particles have pores that can absorb radiation. Gamma rays have been used to study the absorption coefficients of cobalt(II) insoluble compounds (Essien and Ekpe, 1998), densities of marine sediments. (Gerland and Villinger, 1995) and soil particle-size distribution (Vaz et al., 1992). In this study, sedimentation rates of ...

Occurrence of different classes of perfluorinated compounds in Greek wastewater treatment plants and determination of their solid–water distribution coefficients

International Nuclear Information System (INIS)

Arvaniti, Olga S.; Ventouri, Elpida I.; Stasinakis, Athanasios S.; Thomaidis, Nikolaos S.

2012-01-01

Highlights: ► Eighteen PFCs were determined in wastewater and sludge samples using LC–MS/MS. ► PFPeA, PFOA and PFOS were the dominating compounds in both WWTPs. ► No significant decrease or even increase of most PFCs was noticed in effluents. ► Distribution coefficients of PFCs were calculated for different types of sludge. ► Sorption potential was affected by the target compound and the type of sludge. - Abstract: The concentrations of eighteen perfluorinated compounds (PFCs: C5–C14 carboxylates, C4, C6–C8 and C10 sulfonates and 3 sulfonamides) were determined in wastewater and sludge samples originating from two different wastewater treatment plants (WWTPs). The analytes were extracted by solid phase extraction (dissolved phase) or sonication followed by solid phase extraction (solid phase). Qualitative and quantitative analyses were performed by LC–MS/MS. According to the results, perfluoropentanoic acid (PFPeA), perfluorooctanoic acid (PFOA) and perfluorooctane sulfonate (PFOS) were dominant in wastewater and sludge samples from both plants. The average concentrations in the raw and treated wastewater ranged up to 75.7 ng L −1 (perfluorotridecanoic acid, PFTrDA) and 76.0 ng L −1 (PFPeA), respectively. Concentrations of most PFCs were higher in effluents than in influents, indicating their formation during wastewater treatment processes. In sewage sludge, the average concentrations ranged up to 6.7 ng g −1 dry weight (PFOS). No significant seasonal variations in PFCs concentrations were observed, while higher concentrations of PFOA, PFOS and perfluorononanoic acid (PFNA) were determined in the WWTP receiving municipal and industrial wastewater. Significantly different distribution coefficient (K d ) values were determined for different PFCs and different type of sludge, ranging between 169 L kg −1 (PFHxS) to 12,922 L kg −1 (PFDA).

Electron energy distribution functions and transport coefficients relevant for air plasmas in the troposphere: impact of humidity and gas temperature

Energy Technology Data Exchange (ETDEWEB)

Gordillo-Vazquez, F J [Instituto de Astrofisica de Andalucia (IAA), CSIC, PO Box 3004, 18080 Granada (Spain); Donko, Z [Research Institute for Solid State Physics and Optics, H-1525 Budapest, PO Box, 49 (Hungary)

2009-08-15

A Boltzmann and Monte Carlo analysis of the electron energy distribution function (EEDF) and transport coefficients for air plasmas is presented for the conditions of the Earth troposphere where some transient luminous events (TLEs) such as blue jets, blue starters and gigantic jets have been observed. According to recent model results (Minschwaner et al 2004 J. Climate 17 1272) supported by the halogen occultation experiment, the relative humidity of the atmospheric air between 0 and 15 km can change between 15% and 100% depending on the altitude investigated and the ground temperature. The latter results cover a region of latitudes between -25 deg. S and +25 deg. N, that is, the Earth tropical region where lightning and TLE activity is quite high. The calculations shown here suggest that the relative humidity has a clear impact on the behaviour of the EEDF and magnitude of the transport coefficients of air plasmas at ground (0 km) and room temperature conditions (293 K). At higher altitudes (11 and 15 km), the influence of the relative humidity is negligible when the values of the gas temperature are assumed to be the 'natural' ones corresponding to those altitudes, that is, {approx}215 K (at 11 km) and {approx}198 K (at 15 km). However, it is found that a small enhancement (of maximum 100 K) in the background gas temperature (that could be reasonably associated with the TLE activity) would lead to a remarkable impact of the relative humidity on the EEDF and transport coefficients of air plasmas under the conditions of blue jets, blue starters and gigantic jets at 11 and 15 km. The latter effects are visible for relatively low reduced electric fields (E/N {<=} 25 Td) that could be controlling the afterglow kinetics of the air plasmas generated by TLEs. However, for much higher fields such as, for instance, 400 Td (representative of the fields in the streamer coronas and lightning leaders), the impact of increasing the relative humidity and gas

Electron energy distribution functions and transport coefficients relevant for air plasmas in the troposphere: impact of humidity and gas temperature

International Nuclear Information System (INIS)

Gordillo-Vazquez, F J; Donko, Z

2009-01-01

A Boltzmann and Monte Carlo analysis of the electron energy distribution function (EEDF) and transport coefficients for air plasmas is presented for the conditions of the Earth troposphere where some transient luminous events (TLEs) such as blue jets, blue starters and gigantic jets have been observed. According to recent model results (Minschwaner et al 2004 J. Climate 17 1272) supported by the halogen occultation experiment, the relative humidity of the atmospheric air between 0 and 15 km can change between 15% and 100% depending on the altitude investigated and the ground temperature. The latter results cover a region of latitudes between -25 deg. S and +25 deg. N, that is, the Earth tropical region where lightning and TLE activity is quite high. The calculations shown here suggest that the relative humidity has a clear impact on the behaviour of the EEDF and magnitude of the transport coefficients of air plasmas at ground (0 km) and room temperature conditions (293 K). At higher altitudes (11 and 15 km), the influence of the relative humidity is negligible when the values of the gas temperature are assumed to be the 'natural' ones corresponding to those altitudes, that is, ∼215 K (at 11 km) and ∼198 K (at 15 km). However, it is found that a small enhancement (of maximum 100 K) in the background gas temperature (that could be reasonably associated with the TLE activity) would lead to a remarkable impact of the relative humidity on the EEDF and transport coefficients of air plasmas under the conditions of blue jets, blue starters and gigantic jets at 11 and 15 km. The latter effects are visible for relatively low reduced electric fields (E/N ≤ 25 Td) that could be controlling the afterglow kinetics of the air plasmas generated by TLEs. However, for much higher fields such as, for instance, 400 Td (representative of the fields in the streamer coronas and lightning leaders), the impact of increasing the relative humidity and gas temperature is only slightly

Evaluation of distribution coefficients and concentration ratios of ⁹⁰Sr and ¹³⁷Cs in the Techa River and the Miass River

OpenAIRE

Shishkina, Elena A.; Pryakhin, Evgeny A.; Popova, Irina Ya.; Osipov, Denis I.; Tikhova, Yu.; Andreyev, S.S.; Shaposhnikova, I.A.; Egoreichenkov, E.A.; Styazhkina, E.V.; Deryabina, Larisa V.; Tryapitsina, Galina A.; Melnikov, Viktor S.; Rudolfsen, Geir; Teien, Hans-Christian; Sneve, Malgorzata Karpov

2016-01-01

Source:http://www.sciencedirect.com/science/article/pii/S0265931X16300959 Empirical data on the behavior of radionuclides in aquatic ecosystems are needed for radioecological modeling, which is commonly used for predicting transfer of radionuclides, estimating doses, and assessing possible adverse effects on species and communities. Preliminary studies of radioecological parameters including distribution coefficients and concentration ratios, for 90Sr and 137Cs were not in full agreement w...

Migration behavior and sorption mechanisms of radionuclides in sedimentary sand stones

International Nuclear Information System (INIS)

Tanaka, Tadao; Kamiyama, Hideo; Sriyotha, K.

1993-05-01

The influence of crushed particle size and weathering of sedimentary rock on migration behavior and sorption mechanisms of 60 Co, 85 Sr and 137 Cs has been investigated by using the fresh sand stones (classified into two particle size ranges of 1 ∼ 3 mm and 2 , KCl, NH 2 OH-HCl, K-oxalate and H 2 O 2 solutions were carried out, to elucidate their dominated sorption mechanisms. Distribution coefficient values of the all three radionuclides, Kds, for the sand stone of 1 ∼ 3 mm was smaller than that of 85 Sr, and the same irreversible sorptions as the selective sorption of Co onto manganese oxides and fixation of Cs by the layer silicate for 60 Co and 137 Cs, respectively. Larger sorbability of the weathered sand stone was explained to be related to an increase of amounts of the effective sorption site, such as cation exchangeable site, calcite, smectite and manganese oxides, which was possibly caused from metamorphism induced by weathering the fresh sand stone. (author)

Contribution to the evaluation of diffusion coefficients in plasmas containing argon and fluorine

International Nuclear Information System (INIS)

Novakovic, N V

2006-01-01

The theoretical values of the numerical evaluation of the electron and ion diffusion coefficients in plasmas from mixtures of argon and fluorine are presented. The temperature dependence of the diffusion coefficients for low-pressure (from 0.1 to 1.0 kPa) and low-temperature (from 500 to 5000 K) argon plasmas with 20% and 30% of added fluorine are investigated. These values are results of the applications of the specific numerical model to the evaluation plasma composition and transport coefficients in argon plasma with fluorine as additive. It is assumed that the system is kept under constant pressure and that a corresponding state of local thermodynamical equilibrium (LTE) is attained. Since the LTE can be assumed, a Maxwellian electron distribution function will be adopted. The hypothesis of LTE, which is commonly used in most of the numerical evaluations, is analysed with the modified Debye radius r D *. The binary electron and ion diffusion coefficients are calculated with the equilibrium plasma composition and with the collision frequencies. Strictly speaking, Maxwellian distribution function (in the state LTE) is not valid for low pressure, but in this case with the aid of the modified Debye radius, a Maxwellian f e M is assumed correctly. It is shown that the electron diffusion coefficients are about four orders of magnitude larger than the corresponding overall diffusion coefficients of ions. Both diffusion coefficients are lower in argon plasma with 30% than with 20% of fluorine additives, in the whole temperature range examined

Determination of axial diffusion coefficients by the Monte-Carlo method

International Nuclear Information System (INIS)

Milgram, M.

1994-01-01

A simple method to calculate the homogenized diffusion coefficient for a lattice cell using Monte-Carlo techniques is demonstrated. The method relies on modelling a finite reactor volume to induce a curvature in the flux distribution, and then follows a large number of histories to obtain sufficient statistics for a meaningful result. The goal is to determine the diffusion coefficient with sufficient accuracy to test approximate methods built into deterministic lattice codes. Numerical results are given. (author). 4 refs., 8 figs

Technique for Determining Lock Coefficient of Differential "Quif"

Directory of Open Access Journals (Sweden)

A. B. Fominyh

2015-01-01

Full Text Available Increasing the traction qualities of cars on the black ice and snow-covered roads is a relevant task. There are two ways to solve this task, i.e. optimize distribution of the power stream between the driving wheels of the car; introduce a differential (differentials of the increased friction in transmission.Now, an installation of the increased friction differential in transmission is the most widespread measure to increase traction properties of cars. The differential of design "Quif" is one of such differentials. To estimate the efficiency degree of using such a differential is possible either experimentally or theoretically. In case of theoretically determined usefulness of this differential design, as an estimate indicator of the differential installation in transmission a coefficient of lock is accepted.The article considers an algorithm and a technique to calculate a lock coefficient of the differential design "Quif" allowing us to define numeric values of the lock coefficient of such differential at designing stage. It also considers how the lock coefficient depends on the gearing angle and tilt angle of the gear wheel teeth of differential. The given estimating algorithm of designated parameter of differential has more logical and compact structure with regard to the known ones. The lock coefficient values calculated by the offered technique differ from the experimental data by no more than 12%. Taking into account abovementioned, the presented technique for calculating lock coefficient of differential "Quif" is advisable for practical application.

Organ and effective dose rate coefficients for submersion exposure in occupational settings

International Nuclear Information System (INIS)

Veinot, K.G.; Dewji, S.A.; Hiller, M.M.; Eckerman, K.F.; Easterly, C.E.

2017-01-01

External dose coefficients for environmental exposure scenarios are often computed using assumption on infinite or semi-infinite radiation sources. For example, in the case of a person standing on contaminated ground, the source is assumed to be distributed at a given depth (or between various depths) and extending outwards to an essentially infinite distance. In the case of exposure to contaminated air, the person is modeled as standing within a cloud of infinite, or semi-infinite, source distribution. However, these scenarios do not mimic common workplace environments where scatter off walls and ceilings may significantly alter the energy spectrum and dose coefficients. In this paper, dose rate coefficients were calculated using the International Commission on Radiological Protection (ICRP) reference voxel phantoms positioned in rooms of three sizes representing an office, laboratory, and warehouse. For each room size calculations using the reference phantoms were performed for photons, electrons, and positrons as the source particles to derive mono-energetic dose rate coefficients. Since the voxel phantoms lack the resolution to perform dose calculations at the sensitive depth for the skin, a mathematical phantom was developed and calculations were performed in each room size with the three source particle types. Coefficients for the noble gas radionuclides of ICRP Publication 107 (e.g., Ne, Ar, Kr, Xe, and Rn) were generated by folding the corresponding photon, electron, and positron emissions over the mono-energetic dose rate coefficients. Results indicate that the smaller room sizes have a significant impact on the dose rate per unit air concentration compared to the semi-infinite cloud case. For example, for Kr-85 the warehouse dose rate coefficient is 7% higher than the office dose rate coefficient while it is 71% higher for Xe-133. (orig.)

Organ and effective dose rate coefficients for submersion exposure in occupational settings

Energy Technology Data Exchange (ETDEWEB)

Veinot, K.G. [Easterly Scientific, Knoxville, TN (United States); Y-12 National Security Complex, Oak Ridge, TN (United States); Dewji, S.A.; Hiller, M.M. [Center for Radiation Protection Knowledge, Oak Ridge National Laboratory, Oak Ridge, TN (United States); Eckerman, K.F.; Easterly, C.E. [Easterly Scientific, Knoxville, TN (United States)

2017-11-15

External dose coefficients for environmental exposure scenarios are often computed using assumption on infinite or semi-infinite radiation sources. For example, in the case of a person standing on contaminated ground, the source is assumed to be distributed at a given depth (or between various depths) and extending outwards to an essentially infinite distance. In the case of exposure to contaminated air, the person is modeled as standing within a cloud of infinite, or semi-infinite, source distribution. However, these scenarios do not mimic common workplace environments where scatter off walls and ceilings may significantly alter the energy spectrum and dose coefficients. In this paper, dose rate coefficients were calculated using the International Commission on Radiological Protection (ICRP) reference voxel phantoms positioned in rooms of three sizes representing an office, laboratory, and warehouse. For each room size calculations using the reference phantoms were performed for photons, electrons, and positrons as the source particles to derive mono-energetic dose rate coefficients. Since the voxel phantoms lack the resolution to perform dose calculations at the sensitive depth for the skin, a mathematical phantom was developed and calculations were performed in each room size with the three source particle types. Coefficients for the noble gas radionuclides of ICRP Publication 107 (e.g., Ne, Ar, Kr, Xe, and Rn) were generated by folding the corresponding photon, electron, and positron emissions over the mono-energetic dose rate coefficients. Results indicate that the smaller room sizes have a significant impact on the dose rate per unit air concentration compared to the semi-infinite cloud case. For example, for Kr-85 the warehouse dose rate coefficient is 7% higher than the office dose rate coefficient while it is 71% higher for Xe-133. (orig.)

Studies on distribution coefficient (Kd) of naturally occurring radionuclides in geological matrices

International Nuclear Information System (INIS)

Pandit, G.G.

2014-01-01

Accurate prediction of fate and transport of toxic and radioactive metals in the subsurface of uranium tailing pond sites is critical to the assessment of environmental impact and to the development of effective remediation technologies. The mobility of radionuclides and toxic metals is enhanced by acidification of tailings due to sulphide oxidation catalysed by microbial activity. Due to infiltration of water, there is a possibility of leaching of these radionuclides and toxic metals from the tailings pond to the ground water. Sorption onto mineral surfaces is an important mechanism for reducing radionuclide concentrations along ground water flow paths and retarding radionuclide migration to the accessible environment. Reactive transport of ground water contaminants often assume that the reaction governing the retardation of a particular contaminant or radionuclide can be described by simple partitioning constant, K d . This constant is assumed to account for all the reversible sorption processes affecting transport of the contaminant. Experimental determination of site-specific K d values is absolutely essential for the accurate estimation of reactive transport of these contaminants. The results of such studies would be helpful to model migration of these pollutants and to estimate the radiation dose to members of the public through groundwater drinking pathway at different distances from the tailings pond. In the present study it is clearly observed that K d values of most of the radionuclides are strongly dependent on different soil and ground water parameters. The relationships generated between distribution coefficient values of different radionuclides and different soil and ground water parameters can be used to generate look up table. And these relationships can also be used for the prediction of K d values of different radionuclides by using the different physico-chemical parameters of soil and ground water of the particular location

Coefficients of interphase distribution and Gibbs energy of the transfer of nicotinic acid from water into aqueous solutions of ethanol and dimethylsulfoxide

Science.gov (United States)

Grazhdan, K. V.; Gamov, G. A.; Dushina, S. V.; Sharnin, V. A.

2012-11-01

Coefficients of the interphase distribution of nicotinic acid are determined in aqueous solution systems of ethanol-hexane and DMSO-hexane at 25.0 ± 0.1°C. They are used to calculate the Gibbs energy of the transfer of nicotinic acid from water into aqueous solutions of ethanol and dimethylsulfoxide. The Gibbs energy values for the transfer of the molecular and zwitterionic forms of nicotinic acid are obtained by means of UV spectroscopy. The diametrically opposite effect of the composition of binary solvents on the transfer of the molecular and zwitterionic forms of nicotinic acid is noted.

Optimised method to estimate octanol water distribution coefficient (logD) in a high throughput format.

Science.gov (United States)

Low, Ying Wei Ivan; Blasco, Francesca; Vachaspati, Prakash

2016-09-20

Lipophilicity is one of the molecular properties assessed in early drug discovery. Direct measurement of the octanol-water distribution coefficient (logD) requires an analytical method with a large dynamic range or multistep dilutions, as the analyte's concentrations span across several orders of magnitude. In addition, water/buffer and octanol phases which have very different polarity could lead to matrix effects and affect the LC-MS response, leading to erroneous logD values. Most compound libraries use DMSO stocks as it greatly reduces the sample requirement but the presence of DMSO has been shown to underestimate the lipophilicity of the analyte. The present work describes the development of an optimised shake flask logD method using deepwell 96 well plate that addresses the issues related to matrix effects, DMSO concentration and incubation conditions and is also amenable to high throughput. Our results indicate that the equilibrium can be achieved within 30min by flipping the plate on its side while even 0.5% of DMSO is not tolerated in the assay. This study uses the matched matrix concept to minimise the errors in analysing the two phases namely buffer and octanol in LC-MS. Copyright © 2016 Elsevier B.V. All rights reserved.

Separate measurement of local diffusion coefficients in grain boundaries and in adjacent regions

International Nuclear Information System (INIS)

Klotsman, S.M.; Kajgorodov, V.N.

1994-01-01

A new measuring technique is presented that allows one separate determination of grain boundary width and local diffusion coefficients. With the use of the technique presented phenomenological description is accompished for time and temperature dependences of relative and absolute level populations in a zone of preferential intercrystalline diffusion. Local diffusion coefficients obtained for the upper temperature limit of applicability of the technique proposed are in a good agreement with values calculated form coordinate distribution of atoic probes. Local diffusion coefficients determined at lower temperatures essentially differ from those calculated assuming that suction coefficient is equal to a coefficient of volume diffusion. Experimental dta are given for diffusion parameters in Ag, Pd and W polycrystals. 16 refs., 3 figs., 2 tabs

Atomic rate coefficients in a degenerate plasma

Science.gov (United States)

Aslanyan, Valentin; Tallents, Greg

2015-11-01

The electrons in a dense, degenerate plasma follow Fermi-Dirac statistics, which deviate significantly in this regime from the usual Maxwell-Boltzmann approach used by many models. We present methods to calculate the atomic rate coefficients for the Fermi-Dirac distribution and present a comparison of the ionization fraction of carbon calculated using both models. We have found that for densities close to solid, although the discrepancy is small for LTE conditions, there is a large divergence from the ionization fraction by using classical rate coefficients in the presence of strong photoionizing radiation. We have found that using these modified rates and the degenerate heat capacity may affect the time evolution of a plasma subject to extreme ultraviolet and x-ray radiation such as produced in free electron laser irradiation of solid targets.

Metabolic Signatures of Kidney Yang Deficiency Syndrome and Protective Effects of Two Herbal Extracts in Rats Using GC/TOF MS

Directory of Open Access Journals (Sweden)

Linjing Zhao

2013-01-01

Full Text Available Kidney Yang Deficiency Syndrome (KDS-Yang, a typical condition in Chinese medicine, shares similar clinical signs of the glucocorticoid withdrawal syndrome. To date, the underlying mechanism of KDS-Yang has been remained unclear, especially at the metabolic level. In this study, we report a metabolomic profiling study on a classical model of KDS-Yang in rats induced by hydrocortisone injection to characterize the metabolic transformation using gas chromatography/time-of-flight mass spectrometry. WKY1, a polysaccharide extract from Astragalus membranaceus and Lycium barbarum, and WKY2, an aqueous extract from a similar formula containing Astragalus membranaceus, Lycium barbarum, Morinda officinalis, Taraxacum mongolicum, and Cinnamomum cassia presl, were used separately for protective treatments of KDS-Yang. The changes of serum metabolic profiles indicated that significant alterations of key metabolic pathways in response to abrupt hydrocortisone perturbation, including decreased energy metabolism (lactic acid, acetylcarnitine, lipid metabolism (free fatty acids, 1-monolinoleoylglycerol, and cholesterol, gut microbiota metabolism (indole-3-propionic acid, biosynthesis of catecholamine (norepinephrine, and elevated alanine metabolism, were attenuated or normalized with different degrees by the pretreatment of WKY1 or WKY2, which is consistent with the observations in which the two herbal agents could ameliorate biochemical markers of serum cortisone, adrenocorticotropic (ACTH, and urine 17-hydroxycorticosteroids (17-OHCS.

Moderator temperature coefficient in BWR core

International Nuclear Information System (INIS)

Naito, Yoshitaka

1977-01-01

Temperature dependences of infinite multiplication factor k sub(infinity) and neutron leakage from the core must be examined for estimation of moderator temperature coefficient. Temperature dependence on k sub(infinity) has been investigated by many researchers, however, the dependence on neutron leakage of a BWR with cruciformed control rods has hardly been done. Because there are difficulties and necessity on calculations of three space dimensional and multi-energy groups neutron distribution in a BWR core. In this study, moderator temperature coefficients of JPDR-II (BWR) core were obtained by calculation with DIFFUSION-ACE, which is newly developed three-dimensional multi-group computer code. The results were compared with experimental data measured from 20 to 275 0 C of the moderator temperature and the good agreement was obtained between calculation and measurement. In order to evaluate neutron leakage from the core, the other two calculations were carried out, adjusting criticality by uniform absorption rate and by material buckling. The former underestimated neutron leakage and the latter overestimated it. Discussion on the results shows that in order to estimate the temperature coefficient of BWR, neutron leakage must be evaluated precisely, therefore the calculation at actual pattern of control rods is necessary. (auth.)

Coefficients of productivity for Yellowstone's grizzly bear habitat

Science.gov (United States)

Mattson, David John; Barber, Kim; Maw, Ralene; Renkin, Roy

2004-01-01

This report describes methods for calculating coefficients used to depict habitat productivity for grizzly bears in the Yellowstone ecosystem. Calculations based on these coefficients are used in the Yellowstone Grizzly Bear Cumulative Effects Model to map the distribution of habitat productivity and account for the impacts of human facilities. The coefficients of habitat productivity incorporate detailed information that was collected over a 20-year period (1977-96) on the foraging behavior of Yellowstone's bears and include records of what bears were feeding on, when and where they fed, the extent of that feeding activity, and relative measures of the quantity consumed. The coefficients also incorporate information, collected primarily from 1986 to 1992, on the nutrient content of foods that were consumed, their digestibility, characteristic bite sizes, and the energy required to extract and handle each food. Coefficients were calculated for different time periods and different habitat types, specific to different parts of the Yellowstone ecosystem. Stratifications included four seasons of bear activity (spring, estrus, early hyperphagia, late hyperphagia), years when ungulate carrion and whitebark pine seed crops were abundant versus not, areas adjacent to (bear activity in each region, habitat type, and time period were incorporated into calculations, controlling for the effects of proximity to human facilities. The coefficients described in this report and associated estimates of grizzly bear habitat productivity are unique among many efforts to model the conditions of bear habitat because calculations include information on energetics derived from the observed behavior of radio-marked bears.

Effect of Variable Manning Coefficients on Tsunami Inundation

Science.gov (United States)

Barberopoulou, A.; Rees, D.

2017-12-01

Numerical simulations are commonly used to help estimate tsunami hazard, improve evacuation plans, issue or cancel tsunami warnings, inform forecasting and hazard assessments and have therefore become an integral part of hazard mitigation among the tsunami community. Many numerical codes exist for simulating tsunamis, most of which have undergone extensive benchmarking and testing. Tsunami hazard or risk assessments employ these codes following a deterministic or probabilistic approach. Depending on the scope these studies may or may not consider uncertainty in the numerical simulations, the effects of tides, variable friction or estimate financial losses, none of which are necessarily trivial. Distributed manning coefficients, the roughness coefficients used in hydraulic modeling, are commonly used in simulating both riverine and pluvial flood events however, their use in tsunami hazard assessments is primarily part of limited scope studies and for the most part, not a standard practice. For this work, we investigate variations in manning coefficients and their effects on tsunami inundation extent, pattern and financial loss. To assign manning coefficients we use land use maps that come from the New Zealand Land Cover Database (LCDB) and more recent data from the Ministry of the Environment. More than 40 classes covering different types of land use are combined into major classes such as cropland, grassland and wetland representing common types of land use in New Zealand, each of which is assigned a unique manning coefficient. By utilizing different data sources for variable manning coefficients, we examine the impact of data sources and classification methodology on the accuracy of model outputs.

Discharge Coefficient of Rectangular Short-Crested Weir with Varying Slope Coefficients

Directory of Open Access Journals (Sweden)

Yuejun Chen

2018-02-01

Full Text Available Rectangular short-crested weirs are widely used for simple structure and high discharge capacity. As one of the most important and influential factors of discharge capacity, side slope can improve the hydraulic characteristics of weirs at special conditions. In order to systemically study the effects of upstream and downstream slope coefficients S1 and S2 on overflow discharge coefficient in a rectangular short-crested weir the Volume of Fluid (VOF method and the Renormalization Group (RNG κ-ε turbulence model are used. In this study, the slope coefficient ranges from V to 3H:1V and each model corresponds to five total energy heads of H0 ranging from 8.0 to 24.0 cm. Comparisons of discharge coefficients and free surface profiles between simulated and laboratory results display a good agreement. The simulated results show that the difference of discharge coefficients will decrease with upstream slopes and increase with downstream slopes as H0 increases. For a given H0, the discharge coefficient has a convex parabolic relation with S1 and a piecewise linearity relation with S2. The maximum discharge coefficient is always obtained at S2 = 0.8. There exists a difference between upstream and downstream slope coefficients in the influence range of free surface curvatures. Furthermore, a proposed discharge coefficient equation by nonlinear regression is a function of upstream and downstream slope coefficients.

Improved spectral absorption coefficient grouping strategy of wide band k-distribution model used for calculation of infrared remote sensing signal of hot exhaust systems

Science.gov (United States)

Hu, Haiyang; Wang, Qiang

2018-07-01

A new strategy for grouping spectral absorption coefficients, considering the influences of both temperature and species mole ratio inhomogeneities on correlated-k characteristics of the spectra of gas mixtures, has been deduced to match the calculation method of spectral overlap parameter used in multiscale multigroup wide band k-distribution model. By comparison with current spectral absorption coefficient grouping strategies, for which only the influence of temperature inhomogeneity on the correlated-k characteristics of spectra of single species was considered, the improvements in calculation accuracies resulting from the new grouping strategy were evaluated using a series of 0D cases in which radiance under 3-5-μm wave band emitted by hot combustion gas of hydrocarbon fuel was attenuated by atmosphere with quite different temperature and mole ratios of water vapor and carbon monoxide to carbon dioxide. Finally, evaluations are presented on the calculation of remote sensing thermal images of transonic hot jet exhausted from a chevron ejecting nozzle with solid wall cooling system.

The development of a high-throughput measurement method of octanol/water distribution coefficient based on hollow fiber membrane solvent microextraction technique.

Science.gov (United States)

Bao, James J; Liu, Xiaojing; Zhang, Yong; Li, Youxin

2014-09-15

This paper describes the development of a novel high-throughput hollow fiber membrane solvent microextraction technique for the simultaneous measurement of the octanol/water distribution coefficient (logD) for organic compounds such as drugs. The method is based on a designed system, which consists of a 96-well plate modified with 96 hollow fiber membrane tubes and a matching lid with 96 center holes and 96 side holes distributing in 96 grids. Each center hole was glued with a sealed on one end hollow fiber membrane tube, which is used to separate the aqueous phase from the octanol phase. A needle, such as microsyringe or automatic sampler, can be directly inserted into the membrane tube to deposit octanol as the accepted phase or take out the mixture of the octanol and the drug. Each side hole is filled with aqueous phase and could freely take in/out solvent as the donor phase from the outside of the hollow fiber membranes. The logD can be calculated by measuring the drug concentration in each phase after extraction equilibrium. After a comprehensive comparison, the polytetrafluoroethylene hollow fiber with the thickness of 210 μm, an extraction time of 300 min, a temperature of 25 °C and atmospheric pressure without stirring are selected for the high throughput measurement. The correlation coefficient of the linear fit of the logD values of five drugs determined by our system to reference values is 0.9954, showed a nice accurate. The -8.9% intra-day and -4.4% inter-day precision of logD for metronidazole indicates a good precision. In addition, the logD values of eight drugs were simultaneously and successfully measured, which indicated that the 96 throughput measure method of logD value was accurate, precise, reliable and useful for high throughput screening. Copyright © 2014 Elsevier B.V. All rights reserved.

Regional Difference in Specialization Coefficients of Physicians in Nagasaki, Japan

OpenAIRE

Tanimura, Susumu; Mizota, Tsutomu

2004-01-01

In the comparison of municipalities with respect to the medical human resources, not only the number of physicians but also the distribution of their medical practice is important. The objective of the present study was to develop an index appropriate for comparing relatively small municipalities regarding the distribution of physician's medical practice and to apply it to Nagasaki Prefecture, Japan. We modified the specialization coefficient using Bayesian smoothing technique and used it as ...

Evaluation of sorption distribution coefficient of Cs onto granite using sorption data collected in sorption database and sorption model

International Nuclear Information System (INIS)

Nagasaki, S.

2013-01-01

Based on the sorption distribution coefficients (K d ) of Cs onto granite collected from the JAERI Sorption Database (SDB), the parameters for a two-site model without the triple-layer structure were optimized. Comparing the experimentally measured K d values of Cs onto Mizunami granite carried out by JAEA with the K d values predicted by the model, the effect of the ionic strength on the K d values of Cs onto granite was evaluated. It was found that K d values could be determined using the content of biotite in granite at a sodium concentration ([Na]) of 1 x 10 -2 to 5 x 10 -1 mol/dm 3 . It was suggested that in high ionic strength solutions, the sorption of Cs onto other minerals such as microcline should also be taken into account. (author)

Determination coefficient distribution rhenium and tungsten using method extraction with solvent methyl ethyl ketone

International Nuclear Information System (INIS)

Riftanio Natapratama Hidayat; Maria Christina Prihatiningsih; Duyeh Setiawan

2015-01-01

Determination of the distribution coefficient (K d ) of the rhenium and tungsten conducted for the purpose of knowing the value of K d of the two elements. K d value determination is applied to the process of separation rhenium-188 from target of tungsten-188 for the purposes purification of radioisotopes that are made to meet the radionuclide and radiochemical purity. The K d value determination using solvent extraction with methyl ethyl ketone (MEK). Prior to the determination of K d values, determined beforehand the optimum conditions of extraction process based on the effect of agitation time, the volume of MEK, and the pH of the solution. Confirmation the results of the extraction was conducted using UV-Vis spectrophotometer with a complexing KSCN under acidic conditions and reductant SnCl 2 . The results showed that the optimum condition extraction process to feed each of 10 ppm is when the agitation for 10 minutes, the volume of MEK in 20 ml, and the pH below 5. Obtained the maximum recovery of rhenium are drawn to the organic phase as much as 9.545 ppm. However, the condition of the extraction process does not affect the migration of tungsten to the organic phase. Then the maximum K d values obtained at 2.7566 rhenium and tungsten maximum K d is 0.0873. Optimum conditions of extraction process can be further tested on radioactive rhenium and tungsten as an alternative to the separation of radioisotopes. (author)

Investigation on Thrust and Moment Coefficients of a Centrifugal Turbomachine

Directory of Open Access Journals (Sweden)

Bo Hu

2018-04-01

Full Text Available In radial pumps and turbines, the centrifugal through-flow in both the front and the back chambers is quite common. It strongly impacts the core swirl ratio, pressure distribution, axial thrust and frictional torque. In order to investigate these relationships experimentally, a test rig was designed at the University of Duisburg-Essen and described in this paper. Based on both the experimental and numerical results, correlations are determined to predict the impacts of the centrifugal through-flow on the core swirl ratio, the thrust coefficient and the moment coefficient. Two correlations respectively are determined to associate the core swirl ratio with the local through-flow coefficient for both Batchelor type flow and Stewartson type flow. The correlations describing the thrust coefficient and the moment coefficient in a rotor-stator cavity with centripetal through-flow (Hu et al., 2017 are modified for the case of centrifugal through-flow. The Daily and Nece diagram distinguishing between different flow regimes in rotor-stator cavities is extended with a through-flow coordinate into 3D. The achieved results provide a comprehensive data base which is intended to support the calculation of axial thrust and moment coefficients during the design process of radial pumps and turbines in a more accurate manner.

Efficient computation of aerodynamic influence coefficients for aeroelastic analysis on a transputer network

Science.gov (United States)

Janetzke, David C.; Murthy, Durbha V.

1991-01-01

Aeroelastic analysis is multi-disciplinary and computationally expensive. Hence, it can greatly benefit from parallel processing. As part of an effort to develop an aeroelastic capability on a distributed memory transputer network, a parallel algorithm for the computation of aerodynamic influence coefficients is implemented on a network of 32 transputers. The aerodynamic influence coefficients are calculated using a 3-D unsteady aerodynamic model and a parallel discretization. Efficiencies up to 85 percent were demonstrated using 32 processors. The effect of subtask ordering, problem size, and network topology are presented. A comparison to results on a shared memory computer indicates that higher speedup is achieved on the distributed memory system.

Parallel computation of aerodynamic influence coefficients for aeroelastic analysis on a transputer network

Science.gov (United States)

Janetzke, D. C.; Murthy, D. V.

1991-01-01

Aeroelastic analysis is mult-disciplinary and computationally expensive. Hence, it can greatly benefit from parallel processing. As part of an effort to develop an aeroelastic analysis capability on a distributed-memory transputer network, a parallel algorithm for the computation of aerodynamic influence coefficients is implemented on a network of 32 transputers. The aerodynamic influence coefficients are calculated using a three-dimensional unsteady aerodynamic model and a panel discretization. Efficiencies up to 85 percent are demonstrated using 32 processors. The effects of subtask ordering, problem size and network topology are presented. A comparison to results on a shared-memory computer indicates that higher speedup is achieved on the distributed-memory system.

Effects of Void Uncertainties on Pin Power Distributions and the Void Reactivity Coefficient for a 10X10 BWR Assembly

International Nuclear Information System (INIS)

Jatuff, F.; Krouthen, J.; Helmersson, S.; Chawla, R.

2004-01-01

A significant source of uncertainty in Boiling Water Reactor physics is associated with the precise characterisation of the axially-dependent neutron moderation properties of the coolant inside the fuel assembly channel, and the corresponding effects on reactor physics parameters such as the lattice neutron multiplication, the neutron migration length, and the pin-by-pin power distribution. In this paper, the effects of particularly relevant void fraction uncertainties on reactor physics parameters have been studied for a BWR assembly of type Westinghouse SVEA-96 using the CASMO-4, HELIOS/PRESTO-2 and MCNP4C codes. The SVEA-96 geometry is characterised by the sub-division of the assembly into four different sub-bundles by means of an inner bypass with a cruciform shape. The study has covered the following issues: (a) the effects of different cross-section data libraries on the void coefficient of reactivity, for a wide range of void fractions; (b) the effects due to a heterogeneous vs. homogeneous void distribution inside the sub-bundles; and (c) the consequences of partly inserted absorber blades producing different void fractions in different sub-bundles. (author)

Artificial neural network application for predicting soil distribution coefficient of nickel

International Nuclear Information System (INIS)

Falamaki, Amin

2013-01-01

The distribution (or partition) coefficient (K d ) is an applicable parameter for modeling contaminant and radionuclide transport as well as risk analysis. Selection of this parameter may cause significant error in predicting the impacts of contaminant migration or site-remediation options. In this regards, various models were presented to predict K d values for different contaminants specially heavy metals and radionuclides. In this study, artificial neural network (ANN) is used to present simplified model for predicting K d of nickel. The main objective is to develop a more accurate model with a minimal number of parameters, which can be determined experimentally or select by review of different studies. In addition, the effects of training as well as the type of the network are considered. The K d values of Ni is strongly dependent on pH of the soil and mathematical relationships were presented between pH and K d of nickel recently. In this study, the same database of these presented models was used to verify that neural network may be more useful tools for predicting of K d . Two different types of ANN, multilayer perceptron and redial basis function, were used to investigate the effect of the network geometry on the results. In addition, each network was trained by 80 and 90% of the data and tested for 20 and 10% of the rest data. Then the results of the networks compared with the results of the mathematical models. Although the networks trained by 80 and 90% of the data the results show that all the networks predict with higher accuracy relative to mathematical models which were derived by 100% of data. More training of a network increases the accuracy of the network. Multilayer perceptron network used in this study predicts better than redial basis function network. - Highlights: ► Simplified models for predicting K d of nickel presented using artificial neural networks. ► Multilayer perceptron and redial basis function used to predict K d of nickel in

Transformation formulas for legendre coefficients of double-differential cross sections

International Nuclear Information System (INIS)

Shi Xiangjun; Zhang Jingshang

1989-01-01

Approximate analytical formulas have been derived for the transformation of Legendre coefficients of double-differential continuum cross sections of two-body nuclear reactions from the center-of-mass to the laboratory system. This transformation differs from that of elastic-scattering angular distribution coefficients on its accuracy which depends not only upon the target mass, but also upon outgoing energies. A fast code has been written to transform Legendre coefficients of neutron inelastic scattering cross-sections. The calculations have been carried out using a recently introduced numerical integration method for more complicated problems in which the energy spectrum is either an evaporation spectrum or a spectrum obtained from a (pre-)compound model. The results are quite satisfactory provided that the target mass or the outgoing energy is not sufficiently low

Local organ dose conversion coefficients for angiographic examinations of coronary arteries

International Nuclear Information System (INIS)

Schlattl, H; Zankl, M; Hausleiter, J; Hoeschen, C

2007-01-01

New organ dose conversion coefficients for coronary angiographic interventions are presented, as well as dose distributions and resulting maximal local dose conversion coefficients in the relevant organs. For the Monte Carlo based simulations, voxel models of the human anatomy were employed which represent the average Caucasian adult man and woman as defined by the International Commission on Radiological Protection. In the 21 investigated projections, the mean organ dose conversion coefficients vary from a few 0.01 to 2 mGy(Gy cm 2 ) -1 , depending on the projections. However, especially in portions of the lungs and the active bone marrow, the conversion coefficients can locally amount up to 10 mGy(Gy cm 2 ) -1 , which is half the average conversion coefficient of the skin at the field entrance. In addition to the dose conversion coefficients, the dependence of the patient dose on the projection has been estimated. It could be shown that the patient doses are highest for left anterior oblique views with strong caudal or cranial orientation. Nevertheless, for a large range of image-intensifier positions no significant dose differences could be found

Accurate reactivity void coefficient calculation for the fast spectrum reactor FBR-IME

Energy Technology Data Exchange (ETDEWEB)

Lima, Fabiano P.C.; Vellozo, Sergio de O.; Velozo, Marta J., E-mail: fabianopetruceli@outlook.com, E-mail: vellozo@cbpf.br, E-mail: martajann@gmail.com [Instituto Militar de Engenharia (IME), Rio de Janeiro, RJ (Brazil). Secao de Engenharia Militar

2017-07-01

This paper aims to present an accurate calculation of the void reactivity coefficient for the FBR-IME, a fast spectrum reactor in development at the Engineering Military Institute (IME). The main design peculiarity lies in using mixed oxide [MOX - PuO{sub 2} + U(natural uranium)O{sub 2}] as fuel core. For this task, SCALE system was used to calculate the reactivity for several voids distributions generated by bubbles in the sodium beyond its boiling point. The results show that although the void reactivity coefficient is positive and location dependent, they are offset by other feedback effects, resulting in a negative overall coefficient. (author)

Estimating Subcatchment Runoff Coefficients using Weather Radar and a Downstream Runoff Sensor

DEFF Research Database (Denmark)

Ahm, Malte; Thorndahl, Søren Liedtke; Rasmussen, Michael R.

2013-01-01

This paper presents a method for estimating runoff coefficients of urban drainage subcatchments based on a combination of high resolution weather radar data and flow measurements from a downstream runoff sensor. By utilising the spatial variability of the precipitation it is possible to estimate...... the runoff coefficients of the separate subcatchments. The method is demonstrated through a case study of an urban drainage catchment (678 ha) located in the city of Aarhus, Denmark. The study has proven that it is possible to use corresponding measurements of the relative rainfall distribution over...... the catchment and downstream runoff measurements to identify the runoff coefficients at subcatchment level....

Estimating subcatchment runoff coefficients using weather radar and a downstream runoff sensor.

Science.gov (United States)

Ahm, Malte; Thorndahl, Søren; Rasmussen, Michael R; Bassø, Lene

2013-01-01

This paper presents a method for estimating runoff coefficients of urban drainage subcatchments based on a combination of high resolution weather radar data and flow measurements from a downstream runoff sensor. By utilising the spatial variability of the precipitation it is possible to estimate the runoff coefficients of the separate subcatchments. The method is demonstrated through a case study of an urban drainage catchment (678 ha) located in the city of Aarhus, Denmark. The study has proven that it is possible to use corresponding measurements of the relative rainfall distribution over the catchment and downstream runoff measurements to identify the runoff coefficients at subcatchment level.

Measurement of Turbulent Skin Friction Drag Coefficients Produced by Distributed Surface Roughness of Pristine Marine Coatings

DEFF Research Database (Denmark)

Zafiryadis, Frederik; Meyer, Knud Erik; Gökhan Ergin, F.

drag coefficients as well as roughness Reynolds numbers for the various marine coatings across the range of Rex by fitting of the van Driest profile. The results demonstrate sound agreement with the present ITTC method for determining skin friction coefficients for practically smooth surfaces at low...... Reynolds numbers compared to normal operation mode for the antifouling coatings. Thus, better estimates for skin friction of rough hulls can be realised using the proposed method to optimise preliminary vessel design....

Stable Parameter Estimation for Autoregressive Equations with Random Coefficients

Directory of Open Access Journals (Sweden)

V. B. Goryainov

2014-01-01

Full Text Available In recent yearsthere has been a growing interest in non-linear time series models. They are more flexible than traditional linear models and allow more adequate description of real data. Among these models a autoregressive model with random coefficients plays an important role. It is widely used in various fields of science and technology, for example, in physics, biology, economics and finance. The model parameters are the mean values of autoregressive coefficients. Their evaluation is the main task of model identification. The basic method of estimation is still the least squares method, which gives good results for Gaussian time series, but it is quite sensitive to even small disturbancesin the assumption of Gaussian observations. In this paper we propose estimates, which generalize the least squares estimate in the sense that the quadratic objective function is replaced by an arbitrary convex and even function. Reasonable choice of objective function allows you to keep the benefits of the least squares estimate and eliminate its shortcomings. In particular, you can make it so that they will be almost as effective as the least squares estimate in the Gaussian case, but almost never loose in accuracy with small deviations of the probability distribution of the observations from the Gaussian distribution.The main result is the proof of consistency and asymptotic normality of the proposed estimates in the particular case of the one-parameter model describing the stationary process with finite variance. Another important result is the finding of the asymptotic relative efficiency of the proposed estimates in relation to the least squares estimate. This allows you to compare the two estimates, depending on the probability distribution of innovation process and of autoregressive coefficients. The results can be used to identify an autoregressive process, especially with nonGaussian nature, and/or of autoregressive processes observed with gross

Selection of distribution coefficients for contaminant fate and transport calculations: Strontium as a case study

International Nuclear Information System (INIS)

Kaplan, D.I.; Krupka, K.M.; Serne, R.J.

1997-01-01

As part of an ongoing project funded by a cooperative effort involving the Office of Radiation and Indoor Air (ORIA) of the U.S. Environmental Protection Agency (EPA), the Office of Environmental Restoration (EM-40) of the Department of Energy (DOE), and the Nuclear Regulatory Agency (NRC), distribution coefficient (K d ) values are being compiled from the literature to develop provisional tables for cadmium, cesium, chromium, lead, plutonium, strontium, thorium, and uranium. The tables are organized according to important aqueous- and solid-phase parameters affecting the sorption of these contaminants. These parameters, which vary with contaminant, include pH and redox conditions; cation exchange capacity (CEC); presence of iron-oxide, aluminum-oxide, clay, and mica minerals; organic matter content; and solution concentrations of contaminants, competing ions, and complexing ligands. Sorption information compiled for strontium is used to illustrate our approach. The strontium data show how selected geochemical parameters (i.e., CEC, pH, and clay content) affect Strontium K d values and the selection of open-quote default close-quote K d values needed for modeling contaminant transport and risks at sites for which site specific data are lacking. Results of our evaluation may be used by site management and technical staff to assess contaminant fate, migration, and risk calculations in support of site remediation and waste management decisions

Study on the influence of X-ray tube spectral distribution on the analysis of bulk samples and thin films: Fundamental parameters method and theoretical coefficient algorithms

International Nuclear Information System (INIS)

Sitko, Rafal

2008-01-01

Knowledge of X-ray tube spectral distribution is necessary in theoretical methods of matrix correction, i.e. in both fundamental parameter (FP) methods and theoretical influence coefficient algorithms. Thus, the influence of X-ray tube distribution on the accuracy of the analysis of thin films and bulk samples is presented. The calculations are performed using experimental X-ray tube spectra taken from the literature and theoretical X-ray tube spectra evaluated by three different algorithms proposed by Pella et al. (X-Ray Spectrom. 14 (1985) 125-135), Ebel (X-Ray Spectrom. 28 (1999) 255-266), and Finkelshtein and Pavlova (X-Ray Spectrom. 28 (1999) 27-32). In this study, Fe-Cr-Ni system is selected as an example and the calculations are performed for X-ray tubes commonly applied in X-ray fluorescence analysis (XRF), i.e., Cr, Mo, Rh and W. The influence of X-ray tube spectra on FP analysis is evaluated when quantification is performed using various types of calibration samples. FP analysis of bulk samples is performed using pure-element bulk standards and multielement bulk standards similar to the analyzed material, whereas for FP analysis of thin films, the bulk and thin pure-element standards are used. For the evaluation of the influence of X-ray tube spectra on XRF analysis performed by theoretical influence coefficient methods, two algorithms for bulk samples are selected, i.e. Claisse-Quintin (Can. Spectrosc. 12 (1967) 129-134) and COLA algorithms (G.R. Lachance, Paper Presented at the International Conference on Industrial Inorganic Elemental Analysis, Metz, France, June 3, 1981) and two algorithms (constant and linear coefficients) for thin films recently proposed by Sitko (X-Ray Spectrom. 37 (2008) 265-272)

Modelling the impact of blood flow on the temperature distribution in the human eye and the orbit: fixed heat transfer coefficients versus the Pennes bioheat model versus discrete blood vessels

Energy Technology Data Exchange (ETDEWEB)

Flyckt, V M M; Raaymakers, B W; Lagendijk, J J W [Department of Radiotherapy, University Medical Center Utrecht, Heidelberglaan 100, 3584 CX Utrecht (Netherlands)

2006-10-07

Prediction of the temperature distribution in the eye depends on how the impact of the blood flow is taken into account. Three methods will be compared: a simplified eye anatomy that applies a single heat transfer coefficient to describe all heat transport mechanisms between the sclera and the body core, a detailed eye anatomy in which the blood flow is accounted for either by the bioheat approach, or by including the discrete vasculature in the eye and the orbit. The comparison is done both for rabbit and human anatomies, normo-thermally and when exposed to homogeneous power densities. The first simplified model predicts much higher temperatures than the latter two. It was shown that the eye is very hard to heat when taking physiological perfusion correctly into account. It was concluded that the heat transfer coefficient describing the heat transport from the sclera to the body core reported in the literature for the first simplified model is too low. The bioheat approach is appropriate for a first-order approximation of the temperature distribution in the eye when exposed to a homogeneous power density, but the discrete vasculature down to 0.2 mm in diameter needs to be taken into account when the heterogeneity of the temperature distribution at a mm scale is of interest.

Modelling the impact of blood flow on the temperature distribution in the human eye and the orbit: fixed heat transfer coefficients versus the Pennes bioheat model versus discrete blood vessels

International Nuclear Information System (INIS)

Flyckt, V M M; Raaymakers, B W; Lagendijk, J J W

2006-01-01

Prediction of the temperature distribution in the eye depends on how the impact of the blood flow is taken into account. Three methods will be compared: a simplified eye anatomy that applies a single heat transfer coefficient to describe all heat transport mechanisms between the sclera and the body core, a detailed eye anatomy in which the blood flow is accounted for either by the bioheat approach, or by including the discrete vasculature in the eye and the orbit. The comparison is done both for rabbit and human anatomies, normo-thermally and when exposed to homogeneous power densities. The first simplified model predicts much higher temperatures than the latter two. It was shown that the eye is very hard to heat when taking physiological perfusion correctly into account. It was concluded that the heat transfer coefficient describing the heat transport from the sclera to the body core reported in the literature for the first simplified model is too low. The bioheat approach is appropriate for a first-order approximation of the temperature distribution in the eye when exposed to a homogeneous power density, but the discrete vasculature down to 0.2 mm in diameter needs to be taken into account when the heterogeneity of the temperature distribution at a mm scale is of interest

Spatial Distribution of the Coefficient of Variation and Bayesian Forecast for the Paleo-Earthquakes in Japan

Science.gov (United States)

Nomura, Shunichi; Ogata, Yosihiko

2016-04-01

We propose a Bayesian method of probability forecasting for recurrent earthquakes of inland active faults in Japan. Renewal processes with the Brownian Passage Time (BPT) distribution are applied for over a half of active faults in Japan by the Headquarters for Earthquake Research Promotion (HERP) of Japan. Long-term forecast with the BPT distribution needs two parameters; the mean and coefficient of variation (COV) for recurrence intervals. The HERP applies a common COV parameter for all of these faults because most of them have very few specified paleoseismic events, which is not enough to estimate reliable COV values for respective faults. However, different COV estimates are proposed for the same paleoseismic catalog by some related works. It can make critical difference in forecast to apply different COV estimates and so COV should be carefully selected for individual faults. Recurrence intervals on a fault are, on the average, determined by the long-term slip rate caused by the tectonic motion but fluctuated by nearby seismicities which influence surrounding stress field. The COVs of recurrence intervals depend on such stress perturbation and so have spatial trends due to the heterogeneity of tectonic motion and seismicity. Thus we introduce a spatial structure on its COV parameter by Bayesian modeling with a Gaussian process prior. The COVs on active faults are correlated and take similar values for closely located faults. It is found that the spatial trends in the estimated COV values coincide with the density of active faults in Japan. We also show Bayesian forecasts by the proposed model using Markov chain Monte Carlo method. Our forecasts are different from HERP's forecast especially on the active faults where HERP's forecasts are very high or low.

Determination of Flow Resistance Coefficient for Vegetation in Open Channel: Laboratory study

Science.gov (United States)

Aliza Ahmad, Noor; Ali, ZarinaMd; Arish, Nur Aini Mohd; Munirah Mat Daud, Azra; Fatin Amirah Alias, Nur

2018-04-01

This study focused on determination of flow resistances coefficient for grass in an open channel. Laboratory works were conducted to examine the effects of varying of roughness elements on the flume to determine flow resistance coefficient and also to determine the optimum flow resistance with five different flow rate, Q. Laboratory study with two type of vegetation which are Cow Grass and Pearl Grass were implementing to the bed of a flume. The roughness coefficient, n value is determine using Manning’s equation while Soil Conservation Services (SCS) method was used to determine the surface resistance. From the experiment, the flow resistance coefficient for Cow Grass in range 0.0008 - 0.0039 while Pearl Grass value for the flow resistance coefficient are in between 0.0013 - 0.0054. As a conclusion the vegetation roughness value in open channel are depends on density, distribution type of vegetation used and physical characteristic of the vegetation itself

Evaluation of sorption distribution coefficient of Cs onto granite using sorption data collected in sorption database and sorption model

Energy Technology Data Exchange (ETDEWEB)

Nagasaki, S., E-mail: nagasas@mcmaster.ca [McMaster Univ., Hamilton, Ontario (Canada)

2013-07-01

Based on the sorption distribution coefficients (K{sub d}) of Cs onto granite collected from the JAERI Sorption Database (SDB), the parameters for a two-site model without the triple-layer structure were optimized. Comparing the experimentally measured K{sub d} values of Cs onto Mizunami granite carried out by JAEA with the K{sub d} values predicted by the model, the effect of the ionic strength on the K{sub d} values of Cs onto granite was evaluated. It was found that K{sub d} values could be determined using the content of biotite in granite at a sodium concentration ([Na]) of 1 x 10{sup -2} to 5 x 10{sup -1} mol/dm{sup 3} . It was suggested that in high ionic strength solutions, the sorption of Cs onto other minerals such as microcline should also be taken into account. (author)

Simulation of temporal and spatial distribution of required irrigation water by crop models and the pan evaporation coefficient method

Science.gov (United States)

Yang, Yan-min; Yang, Yonghui; Han, Shu-min; Hu, Yu-kun

2009-07-01

Hebei Plain is the most important agricultural belt in North China. Intensive irrigation, low and uneven precipitation have led to severe water shortage on the plain. This study is an attempt to resolve this crucial issue of water shortage for sustainable agricultural production and water resources management. The paper models distributed regional irrigation requirement for a range of cultivated crops on the plain. Classic crop models like DSSAT- wheat/maize and COTTON2K are used in combination with pan-evaporation coefficient method to estimate water requirements for wheat, corn, cotton, fruit-trees and vegetables. The approach is more accurate than the static approach adopted in previous studies. This is because the combination use of crop models and pan-evaporation coefficient method dynamically accounts for irrigation requirement at different growth stages of crops, agronomic practices, and field and climatic conditions. The simulation results show increasing Required Irrigation Amount (RIA) with time. RIA ranges from 5.08×109 m3 to 14.42×109 m3 for the period 1986~2006, with an annual average of 10.6×109 m3. Percent average water use by wheat, fruit trees, vegetable, corn and cotton is 41%, 12%, 12%, 11%, 7% and 17% respectively. RIA for April and May (the period with the highest irrigation water use) is 1.78×109 m3 and 2.41×109 m3 respectively. The counties in the piedmont regions of Mount Taihang have high RIA while the central and eastern regions/counties have low irrigation requirement.

Copper and zinc distribution coefficients for sandy aquifer materials

DEFF Research Database (Denmark)

Christensen, Thomas Højlund; Astrup, Thomas; Boddum, J. K.

2000-01-01

Distribution coe�cients (Kd) were measured for copper (Cu) and zinc (Zn) in laboratory batch experiments for 17 sandy aquifer materials at environmentally relevant solute concentrations (Cu: 5±300 mg/l, Zn: 20±3100 mg/l). The Kd values ranged two to three orders of magnitude (Cu: 70±10,800 l/ kg...

Semiempirical calculation of van der Waals coefficients for alkali-metal and alkaline-earth-metal atoms

International Nuclear Information System (INIS)

Mitroy, J.; Bromley, M.W.J.

2003-01-01

The van der Waals coefficients, C 6 , C 8 , and C 10 for the alkali-metal (Li, Na, K, and Rb) and alkaline-earth-metal (Be, Mg, Ca, and Sr) atoms are estimated by a combination of ab initio and semiempirical methods. Polarizabilities and atom-wall coefficients are given as a diagnostic check, and the lowest order nonadiabatic dispersion coefficient, D 8 and the three-body coefficient, C 9 are also presented. The dispersion coefficients are in agreement with the available relativistic many-body perturbation theory calculations. The contribution from the core was included by using constrained sum rules involving the core polarizability and Hartree-Fock expectation values to estimate the f-value distribution

Computation of Clebsch-Gordan and Gaunt coefficients using binomial coefficients

International Nuclear Information System (INIS)

Guseinov, I.I.; Oezmen, A.; Atav, Ue

1995-01-01

Using binomial coefficients the Clebsch-Gordan and Gaunt coefficients were calculated for extremely large quantum numbers. The main advantage of this approach is directly calculating these coefficients, instead of using recursion relations. Accuracy of the results is quite high for quantum numbers l 1 , and l 2 up to 100. Despite direct calculation, the CPU times are found comparable with those given in the related literature. 11 refs., 1 fig., 2 tabs

Meta-analytical synthesis of regression coefficients under different categorization scheme of continuous covariates.

Science.gov (United States)

Yoneoka, Daisuke; Henmi, Masayuki

2017-11-30

Recently, the number of clinical prediction models sharing the same regression task has increased in the medical literature. However, evidence synthesis methodologies that use the results of these regression models have not been sufficiently studied, particularly in meta-analysis settings where only regression coefficients are available. One of the difficulties lies in the differences between the categorization schemes of continuous covariates across different studies. In general, categorization methods using cutoff values are study specific across available models, even if they focus on the same covariates of interest. Differences in the categorization of covariates could lead to serious bias in the estimated regression coefficients and thus in subsequent syntheses. To tackle this issue, we developed synthesis methods for linear regression models with different categorization schemes of covariates. A 2-step approach to aggregate the regression coefficient estimates is proposed. The first step is to estimate the joint distribution of covariates by introducing a latent sampling distribution, which uses one set of individual participant data to estimate the marginal distribution of covariates with categorization. The second step is to use a nonlinear mixed-effects model with correction terms for the bias due to categorization to estimate the overall regression coefficients. Especially in terms of precision, numerical simulations show that our approach outperforms conventional methods, which only use studies with common covariates or ignore the differences between categorization schemes. The method developed in this study is also applied to a series of WHO epidemiologic studies on white blood cell counts. Copyright © 2017 John Wiley & Sons, Ltd.

Research on bimodal particle extinction coefficient during Brownian coagulation and condensation for the entire particle size regime

International Nuclear Information System (INIS)

Tang Hong; Lin Jianzhong

2011-01-01

The extinction coefficient of atmospheric aerosol particles influences the earth’s radiation balance directly or indirectly, and it can be determined by the scattering and absorption characteristics of aerosol particles. The problem of estimating the change of extinction coefficient due to time evolution of bimodal particle size distribution is studied, and two improved methods for calculating the Brownian coagulation coefficient and the condensation growth rate are proposed, respectively. Through the improved method based on Otto kernel, the Brownian coagulation coefficient can be expressed simply in powers of particle volume for the entire particle size regime based on the fitted polynomials of the mean enhancement function. Meanwhile, the improved method based on Fuchs–Sutugin kernel is developed to obtain the condensation growth rate for the entire particle size regime. And then, the change of the overall extinction coefficient of bimodal distributions undergoing Brownian coagulation and condensation can be estimated comprehensively for the entire particle size regime. Simulation experiments indicate that the extinction coefficients obtained with the improved methods coincide fairly well with the true values, which provide a simple, reliable, and general method to estimate the change of extinction coefficient for the entire particle size regime during the bimodal particle dynamic processes.

Fourier coefficientes computation in two variables, a distributional version

OpenAIRE

Carlos Manuel Ulate R.

2015-01-01

The present article, by considering the distributional summations of Euler-Maclaurin and a suitable choice of the distribution, results in repre- sentations for the Fourier coefficients in two variables are obtained. These representations may be used for the numerical evaluation of coefficients.

Derivation of Coefficients for the Bidirectional Reflection Distribution Function from AVHRR-data over Europe, under Consideration of the Helmholtz Reciprocity Law

Science.gov (United States)

Billing, H.; Koslowsky, D.

In the AVHRR data of the polar orbiting NOAA Satellites, directional reflectance under a certain view from satellite and a certain illumination by the sun is measured. Due to the nearly sunsynchroneous orbit of the NOAA satellite, each area is seen under different viewing angles in successive days. Only after approximately 9 days, the conditions are again similar. Areas, seen in specular direction, may appear only half as bright, as if seen in antispecular direction. This deviation from a Lambertian reflector is a function of the surface roughness and the degree of coverage with vegetation. The NOAA afternoon satellites drift by half an hour from year to year. Thus even data from the same season, but different years, are seen under different illumination conditions. To derive the bidirectional reflection distribution function in dependence on satellite viewing angle and solar illumination becomes a very complicated procedure. Using the Helmholtz reciprocity principle (HRP), i.e. the symetrie in viewing and illumination, reduces the problem by one dimension. For different bidimensional reflection laws it will be tested, whether they can be formulated to fullfill the HRP. Via regression, the parameters will be deduced for time series of AVHRR data of 10 years from NOAA 11,14,16 and 17. Brdfunctions, suggested by Rao as well as a law, suggested by Ba seem to become unstable for low sun resp. large viewing zenit angles. Only brdfs with 4 coefficients can fit the observed distributions. A nonlinear temporal angular model (NTAM), suggested by Latifovic,Cihlar and Chen, seems to be suitable to describe even the hot spot and the dependence on plant growth. The coefficients of these brdf-function will be derived via regression for monthly series of cloud free data for the European area, where AVHRR data in full resolution are received in Berlin. Using these coefficients, monthly maps of surface roughness are produced for the above area for the time since 1985. Ba, M

Shear viscosity coefficient from microscopic models

International Nuclear Information System (INIS)

Muronga, Azwinndini

2004-01-01

The transport coefficient of shear viscosity is studied for a hadron matter through microscopic transport model, the ultrarelativistic quantum molecular dynamics (UrQMD), using the Green-Kubo formulas. Molecular-dynamical simulations are performed for a system of light mesons in a box with periodic boundary conditions. Starting from an initial state composed of π,η,ω,ρ,φ with a uniform phase-space distribution, the evolution takes place through elastic collisions, production, and annihilation. The system approaches a stationary state of mesons and their resonances, which is characterized by common temperature. After equilibration, thermodynamic quantities such as the energy density, particle density, and pressure are calculated. From such an equilibrated state the shear viscosity coefficient is calculated from the fluctuations of stress tensor around equilibrium using Green-Kubo relations. We do our simulations here at zero net baryon density so that the equilibration times depend on the energy density. We do not include hadron strings as degrees of freedom so as to maintain detailed balance. Hence we do not get the saturation of temperature but this leads to longer equilibration times

Fourier coefficientes computation in two variables, a distributional version

Directory of Open Access Journals (Sweden)

Carlos Manuel Ulate R.

2015-01-01

Full Text Available The present article, by considering the distributional summations of Euler-Maclaurin and a suitable choice of the distribution, results in repre- sentations for the Fourier coefficients in two variables are obtained. These representations may be used for the numerical evaluation of coefficients.

Determination of the coefficient of uranium and thorium distribution in phosphogypsum for their use in sanitary landfills

Energy Technology Data Exchange (ETDEWEB)

Marchesi, Marcos Vinicius A.; Hama, Naruhiko; Jacomino, Vanusa M. F.; Ladeira, Ana Claudia Q.; Cota, Stela D. S., E-mail: mvmarchesi@hotmail.com, E-mail: sdsc@cdtn.br, E-mail: vmfj@cdtn.br, E-mail: ana.ladeira@cdtn.br, E-mail: naruhikohama@hotmail.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil); Nascimento, Marcos Roberto Lopes do; Taddei, Maria Helena, E-mail: pmarcos@cnen.gov.br, E-mail: mhtaddei@cnen.gov.br [Comissao Nacional de Energia Nuclear (LAPOC/CNEN), Pocos de Caldas, MG (Brazil). Laboratorio de Pocos de Caldas

2013-07-01

Phosphogypsum is a byproduct from the production of phosphoric acid, and contain radionuclides, heavy metals and metalloids from phosphate rock. It represents a risk to the environment if improperly stored. Because it is composed mainly of dihydrated calcium sulphate, phosphogypsum can be used in anaerobic environments such as those found in landfills to accelerate microbial processes of decomposition of municipal solid waste and thus increase the life of these facilities. One of the options of your application being studied is the use of phosphogypsum replacing the covers of soil/clay in landfills. Besides reducing the demand for soil and clay, this application would be an alternative to disposal of the waste, since the alternatives are not sufficient for more than five million tons produced per year in Brazil. To ensure the safety of this application, the potential environmental impact of contaminants in phosphogypsum should be evaluated. The rate of leaching of contaminants are being studied by determining the coefficient of distribution of the contaminants in the phosphogypsum. Batch tests were performed by mixing different proportions of slurry and phosphogypsum. This work presents the results for the chain of uranium and natural thorium.

Determination of the coefficient of uranium and thorium distribution in phosphogypsum for their use in sanitary landfills

International Nuclear Information System (INIS)

Marchesi, Marcos Vinicius A.; Hama, Naruhiko; Jacomino, Vanusa M. F.; Ladeira, Ana Claudia Q.; Cota, Stela D. S.; Nascimento, Marcos Roberto Lopes do; Taddei, Maria Helena

2013-01-01

Phosphogypsum is a byproduct from the production of phosphoric acid, and contain radionuclides, heavy metals and metalloids from phosphate rock. It represents a risk to the environment if improperly stored. Because it is composed mainly of dihydrated calcium sulphate, phosphogypsum can be used in anaerobic environments such as those found in landfills to accelerate microbial processes of decomposition of municipal solid waste and thus increase the life of these facilities. One of the options of your application being studied is the use of phosphogypsum replacing the covers of soil/clay in landfills. Besides reducing the demand for soil and clay, this application would be an alternative to disposal of the waste, since the alternatives are not sufficient for more than five million tons produced per year in Brazil. To ensure the safety of this application, the potential environmental impact of contaminants in phosphogypsum should be evaluated. The rate of leaching of contaminants are being studied by determining the coefficient of distribution of the contaminants in the phosphogypsum. Batch tests were performed by mixing different proportions of slurry and phosphogypsum. This work presents the results for the chain of uranium and natural thorium

Simulating Osmotic Equilibria: A New Tool for Calculating Activity Coefficients in Concentrated Aqueous Salt Solutions.

Science.gov (United States)

Bley, Michael; Duvail, Magali; Guilbaud, Philippe; Dufrêche, Jean-François

2017-10-19

Herein, a new theoretical method is presented for predicting osmotic equilibria and activities, where a bulk liquid and its corresponding vapor phase are simulated by means of molecular dynamics using explicit polarization. Calculated time-averaged number density profiles provide the amount of evaporated molecules present in the vapor phase and consequently the vapor-phase density. The activity of the solvent and the corresponding osmotic coefficient are determined by the vapor density at different solute concentrations with respect to the reference vapor density of the pure solvent. With the extended Debye-Hückel equation for the activity coefficient along with the corresponding Gibbs-Duhem relation, the activity coefficients of the solutes are calculated by fitting the osmotic coefficients. A simple model based on the combination of Poisson processes and Maxwell-Boltzmann velocity distributions is introduced to interpret statistical phenomena observed during the simulations, which are related to evaporation and recondensation. This method is applied to aqueous dysprosium nitrate [Dy(NO 3 ) 3 ] solutions at different concentrations. The obtained densities of the liquid bulk and the osmotic and activity coefficients are in good agreement with the experimental results for concentrated and saturated solutions. Density profiles of the liquid-vapor interface at different concentrations provide detailed insight into the spatial distributions of all compounds.

Coefficient estimates of negative powers and inverse coefficients for ...

Indian Academy of Sciences (India)

and the inequality is sharp for the inverse of the Koebe function k(z) = z/(1 − z)2. An alternative approach to the inverse coefficient problem for functions in the class S has been investigated by Schaeffer and Spencer [27] and FitzGerald [6]. Although, the inverse coefficient problem for the class S has been completely solved ...

Effect of retardation coefficient for radionuclide migration on assessment results of environmental impact

International Nuclear Information System (INIS)

Wang Zhiming

2004-01-01

Environmental impact report is an important content in enforcing environmental impact assessment system. Effect of retardation coefficient used in models of radionuclide migration in geological media on the calculated results of maximum concentration of calculated points at the lower reaches is discussed in this paper. It is shown from experimental results that the retardation coefficient is not a constant. And it is shown from calculated results that retardation coefficient obviously affect the calculated results of maximum concentration of calculated point at the lower reaches. Conservation level of the assessment results would considerably be affected, and hence confidence level of results would be affected if the aspects are not paid enough attention and solved. The paper suggests that retardation coefficient used in migration models should directly be obtained by measurement in the field or in column, rather than using the result derived from distribution coefficients according to some formula in order to prevent the nonconservative results

Ion Exchange Distribution Coefficient Tests and Computer Modeling at High Ionic Strength Supporting Technetium Removal Resin Maturation

Energy Technology Data Exchange (ETDEWEB)

Nash, Charles A. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Hamm, L. Larry [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); Smith, Frank G. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL); McCabe, Daniel J. [Savannah River Site (SRS), Aiken, SC (United States). Savannah River National Lab. (SRNL)

2014-12-19

The primary treatment of the tank waste at the DOE Hanford site will be done in the Waste Treatment and Immobilization Plant (WTP) that is currently under construction. The baseline plan for this facility is to treat the waste, splitting it into High Level Waste (HLW) and Low Activity Waste (LAW). Both waste streams are then separately vitrified as glass and poured into canisters for disposition. The LAW glass will be disposed onsite in the Integrated Disposal Facility (IDF). There are currently no plans to treat the waste to remove technetium, so its disposition path is the LAW glass. Due to the water solubility properties of pertechnetate and long half-life of ⁹⁹Tc, effective management of ⁹⁹Tc is important to the overall success of the Hanford River Protection Project mission. To achieve the full target WTP throughput, additional LAW immobilization capacity is needed, and options are being explored to immobilize the supplemental LAW portion of the tank waste. Removal of ⁹⁹Tc, followed by off-site disposal, would eliminate a key risk contributor for the IDF Performance Assessment (PA) for supplemental waste forms, and has potential to reduce treatment and disposal costs. Washington River Protection Solutions (WRPS) is developing some conceptual flow sheets for supplemental LAW treatment and disposal that could benefit from technetium removal. One of these flowsheets will specifically examine removing ⁹⁹Tc from the LAW feed stream to supplemental immobilization. To enable an informed decision regarding the viability of technetium removal, further maturation of available technologies is being performed. This report contains results of experimental ion exchange distribution coefficient testing and computer modeling using the resin SuperLig^® 639^a to selectively remove perrhenate from high ionic strength simulated LAW. It is advantageous to operate at higher concentration in order to treat the waste

Derivation of the chemical-equilibrium rate coefficient using scattering theory

Science.gov (United States)

Mickens, R. E.

1977-01-01

Scattering theory is applied to derive the equilibrium rate coefficient for a general homogeneous chemical reaction involving ideal gases. The reaction rate is expressed in terms of the product of a number of normalized momentum distribution functions, the product of the number of molecules with a given internal energy state, and the spin-averaged T-matrix elements. An expression for momentum distribution at equilibrium for an arbitrary molecule is presented, and the number of molecules with a given internal-energy state is represented by an expression which includes the partition function.

Heat transfer coefficients for particles in liquid in axially rotating cans

Science.gov (United States)

Hassan, B. H.

A theoretical analysis was carried out to determine the nondimensional parameters and corresponding correlations for the overall heat transfer coefficient (between the external steam and internal rotating liquid) and the liquid-particle film heat transfer coefficient for spherical particles in liquid in axially rotating 303 x 406 cans undergoing steam heating. The correlations were obtained from dimensional analysis of the equations of continuity, motion and energy, together with the thermal energy balances and the particle-fluid dynamics of the system. The theoretical solutions for the temperature distribution in spherical particles with a time varying boundary condition were presented.

Time correlation functions and transport coefficients in a dilute superfluid

International Nuclear Information System (INIS)

Kirkpatrick, T.R.; Dorfman, J.R.

1985-01-01

Time correlation functions for the transport coefficients in the linear Landau-Khalatnikov equations are derived on the basis of a formal theory. These Green--Kubo expressions are then explicitly evaluated for a dilute superfluid and the resulting transport coefficiencts are shown to be identical to those obtained previously by using a distribution function method

Thermodynamic equilibrium model to predict the cobalt distribution coefficient in the CoCl2--HCl--H2O--TBP liquid--liquid extraction system

International Nuclear Information System (INIS)

Nevarez, M.; Bautista, R.G.

1976-01-01

The development of a thermodynamic equilibrium model to predict the cobalt distribution coefficient in the CoCl 2 -HCl-H 2 O-TBP system is described. The model makes use of the various aqueous phase cobaltous chloride complexes stoichiometric stability constants expressed as their degree of formation, their mechanism of extraction into the organic phase, and the equilibrium constant for the extraction reaction. The model was verified by the good agreement between the calculated cobalt distribution coefficients and those obtained experimentally both in the present study and published by other investigators. The optimum extraction of cobalt by the TBP occurred at an HCl equilibrium aqueous place concentration between 8.5 and 9.5M. The development of efficient procedures for the separation and concentration of important industrial metals from their aqueous solutions by liquid-liquid extraction has recently been given impetus by the realization of an impending shortage of energy and mineral resources. Liquid-liquid extraction is one of the few methods by which it is possible to quantitatively separate elements which are similar in properties. The use of liquid-liquid extraction to separate cobalt and nickel, which very frequently occur in nature together, is an important separation problem in nonferrous metallurgy. There is some fundamental information available in the chemical literature regarding the mechanism and equilibrium thermodynamic properties of selected liquid-liquid extraction systems. This research effort shows how this available information can be utilized to improve existing separation and concentration theory and technique. The development and application of a thermodynamic equilibrium model for describing the liquid-liquid extraction of cobaltous chloride from aqueous HCl solutions by tributyl phosphate (TBP) using experimental data obtained in this investigation and from the literature are presented

Converting Sabine absorption coefficients to random incidence absorption coefficients

DEFF Research Database (Denmark)

Jeong, Cheol-Ho

2013-01-01

are suggested: An optimization method for the surface impedances for locally reacting absorbers, the flow resistivity for extendedly reacting absorbers, and the flow resistance for fabrics. With four porous type absorbers, the conversion methods are validated. For absorbers backed by a rigid wall, the surface...... coefficients to random incidence absorption coefficients are proposed. The overestimations of the Sabine absorption coefficient are investigated theoretically based on Miki's model for porous absorbers backed by a rigid wall or an air cavity, resulting in conversion factors. Additionally, three optimizations...... impedance optimization produces the best results, while the flow resistivity optimization also yields reasonable results. The flow resistivity and flow resistance optimization for extendedly reacting absorbers are also found to be successful. However, the theoretical conversion factors based on Miki's model...

Adaptive Neuro-Fuzzy Computing Technique for Determining Turbulent Flow Friction Coefficient

Directory of Open Access Journals (Sweden)

Mohammad Givehchi

2013-08-01

Full Text Available Estimation of the friction coefficient in pipes is very important in many water and wastewater engineering issues, such as distribution of velocity and shear stress, erosion, sediment transport and head loss. In analyzing these problems, knowing the friction coefficient, can obtain estimates that are more accurate. In this study in order to estimate the friction coefficient in pipes, using adaptive neuro-fuzzy inference systems (ANFIS, grid partition method was used. For training and testing of neuro-fuzzy model, the data derived from the Colebrook’s equation was used. In the neuro-fuzzy approach, pipe relative roughness and Reynolds number are considered as input variables and friction coefficient as output variable is considered. Performance of the proposed approach was evaluated by using of the data obtained from the Colebrook’s equation and based on statistical indicators such as coefficient determination (R2, root mean squared error (RMSE and mean absolute error (MAE. The results showed that the adaptive nerou-fuzzy inference system with grid partition method and gauss model as an input membership function and linear as an output function could estimate friction coefficient more accurately than other conditions. The new proposed approach in this paper has capability of application in the practical design issues and can be combined with mathematical and numerical models of sediment transfer or real-time updating of these models.

On a new procedure for determining the diffusion coefficients of swarm electrons

International Nuclear Information System (INIS)

Winkler, R.; Wilhelm, J.; Braglia, G.L.

1985-01-01

A new method for solving the Boltzmann kinetic equation applied to the determination of diffusion coefficients of swarm electrons in a model plasma, and CO 2 and N 2 plasmas is proposed. The method which uses Legendre polynomial expansion of the electron velocity distribution of the stationary and homogeneous plasma, is based upon an analytical isolation of the non-singular part of the general solution from the singular part. The converged values of the diffusion coefficients given by the new method are compared with the results of Monte-Carlo simulations. (D.Gy.)

Heat transfer coefficient as parameter describing ability of insulating liquid to heat transfer

Science.gov (United States)

Nadolny, Zbigniew; Gościński, Przemysław; Bródka, Bolesław

2017-10-01

The paper presents the results of the measurements of heat transfer coefficient of insulating liquids used in transformers. The coefficient describes an ability of the liquid to heat transport. On the basis of the coefficient, effectiveness of cooling system of electric power devices can be estimated. Following liquids were used for the measurements: mineral oil, synthetic ester and natural ester. It was assumed that surface heat load is about 2500 W·m-2, which is equal the load of transformer windings. A height of heat element was 1.6 m, because it makes possible steady distribution of temperature on its surface. The measurements of heat transfer coefficient was made as a function of various position of heat element (vertical, horizontal). In frame of horizontal position of heat element, three suppositions were analysed: top, bottom, and side.

Heat transfer coefficient as parameter describing ability of insulating liquid to heat transfer

Directory of Open Access Journals (Sweden)

Nadolny Zbigniew

2017-01-01

Full Text Available The paper presents the results of the measurements of heat transfer coefficient of insulating liquids used in transformers. The coefficient describes an ability of the liquid to heat transport. On the basis of the coefficient, effectiveness of cooling system of electric power devices can be estimated. Following liquids were used for the measurements: mineral oil, synthetic ester and natural ester. It was assumed that surface heat load is about 2500 W·m-2, which is equal the load of transformer windings. A height of heat element was 1.6 m, because it makes possible steady distribution of temperature on its surface. The measurements of heat transfer coefficient was made as a function of various position of heat element (vertical, horizontal. In frame of horizontal position of heat element, three suppositions were analysed: top, bottom, and side.

Moisture Transfer in Concrete: Numerical Determination of the Capillary Conductivity Coefficient

Directory of Open Access Journals (Sweden)

Simo Elie

2017-03-01

Full Text Available We numerically investigated moisture transfer in buildings made of concrete. We considered three types of concrete: normal concrete, pumice concrete and cellular concrete. We present the results of a 1-D liquid water flow in such materials. We evaluated the moisture distribution in building materials using the Runge-Kutta fourth-and-fifth-order method. The DOPRI5 code was used as an integrator. The model calculated the resulting moisture content and other moisture-dependent physical parameters. The moisture curves were plotted. The dampness data obtained was utilized for the numerical computation of the coefficient of the capillary conductivity of moisture. Different profiles of this coefficient are represented. Calculations were performed for four different values of the outdoor temperature: -5°C, 0°C, 5°C and 10°C. We determined that the curves corresponding to small time intervals of wetting are associated with great amplitudes of the capillary conductivity . The amplitudes of the coefficient of the capillary conductivity decrease as the time interval increases. High outdoor temperatures induce high amplitudes of the coefficient of the capillary conductivity.

Variation of the distribution coefficient (Kd) of selenium in soils under various microbial states

International Nuclear Information System (INIS)

Fevrier, L.; Martin-Garin, A.; Leclerc, E.

2007-01-01

This study aimed to (i) evaluate whether the K d value of selenium is dependent upon the soil microbial activity and (ii) define the limitation of the use of the K d concept to describe selenium behaviour in soils when assessing the long-term radiological waste disposal risk. K d coefficients, as well as information on selenite speciation in the soil-solution, were derived from short- and long-term batch experiments with a calcareous silty clay soil in various microbial states. Soil microbial activity induced (i) an increase of the K d value from 16 l kg -1 in sterile conditions to 130 l kg -1 when the soil was amended with glucose and nitrate, and (ii) changes in selenium speciation both in the solution (presence of seleno-species other than free Se(IV)) and in the solid phase (Se linked to microorganisms). Although the K d coefficient adequately reflects the initial fractionation between soil-solid and soil-solution, it does not allow for speciation and microbial processes, which could affect reversibility, mobility and the long-term accumulation and uptake into crops

Coefficient Alpha: A Reliability Coefficient for the 21st Century?

Science.gov (United States)

Yang, Yanyun; Green, Samuel B.

2011-01-01

Coefficient alpha is almost universally applied to assess reliability of scales in psychology. We argue that researchers should consider alternatives to coefficient alpha. Our preference is for structural equation modeling (SEM) estimates of reliability because they are informative and allow for an empirical evaluation of the assumptions…

Coefficient of friction of a starved lubricated spur gear pair

International Nuclear Information System (INIS)

Liu, Huaiju; Zhu, Caichao; Sun, Zhangdong; Zhang, Yuanyuan; Song, Chaosheng

2016-01-01

The frictional power loss issue of gear pairs becomes an important concern in both industry and academia due to the requirement of the energy saving and the improvement of power density of gear drives. A thermal starved elastohydrodynamic lubrication model is developed to study the tribological performance of a spur gear pair under starved lubrication conditions. The contact pressure, the film thickness, the temperature rise, the frictional power loss, as well as the coefficient of friction are evaluated by considering the variation of the curvature radius, the sliding/rolling motion, and the load distribution of gear tooth within the meshing period. Effects of lubrication starvation condition, load and speed on the coefficient of friction are studied.

Distribution of stress in greenhouses frames estimated by aerodynamic coefficients of Brazilian and European standards

Directory of Open Access Journals (Sweden)

José Gabriel Vieira Neto

2016-04-01

Full Text Available ABSTRACT Widely disseminated in both national and international scenarios, greenhouses are agribusiness solutions which are designed to allow for greater efficiency and control of the cultivation of plants. Bearing this in mind, the construction of greenhouses should take into consideration the incidence of wind, and other such aspects of comfort and safety, and ensure they are factored into the design of structural elements. In this study, we evaluated the effects of pressure coefficients established by the European standard EN 13031-1 (2001 and the Brazilian standard ABNT (1988, which are applicable to the structures of greenhouses with flat roofs, taking into account the following variables: roof slope, external and internal pressure coefficients and height-span ratio of the structure. Using the ANSYSTM computer program, zones of columns and roof were discretized by the Beam44 finite element to identify the maximum and minimum stress portions connected to the aerodynamic coefficients. With this analysis, we found that, in the smallest roof slope (a equal to 20°, the frame stress was quite similar for standards adopted. On the other hand, for the greatest inclination (a equal to 26°, the stress was consistently lower under the Brazilian standard. In view of this, we came to the conclusion that the differences between stresses when applying both standards were more significant at the higher degrees of height-span ratio and roof slope.

The empirical Gaia G-band extinction coefficient

Science.gov (United States)

Danielski, C.; Babusiaux, C.; Ruiz-Dern, L.; Sartoretti, P.; Arenou, F.

2018-06-01

Context. The first Gaia data release unlocked the access to photometric information for 1.1 billion sources in the G-band. Yet, given the high level of degeneracy between extinction and spectral energy distribution for large passbands such as the Gaia G-band, a correction for the interstellar reddening is needed in order to exploit Gaia data. Aims: The purpose of this manuscript is to provide the empirical estimation of the Gaia G-band extinction coefficient kG for both the red giants and main sequence stars in order to be able to exploit the first data release DR1. Methods: We selected two samples of single stars: one for the red giants and one for the main sequence. Both samples are the result of a cross-match between Gaia DR1 and 2MASS catalogues; they consist of high-quality photometry in the G-, J- and KS-bands. These samples were complemented by temperature and metallicity information retrieved from APOGEE DR13 and LAMOST DR2 surveys, respectively. We implemented a Markov chain Monte Carlo method where we used (G - KS)0 versus Teff and (J - KS)0 versus (G - KS)0, calibration relations to estimate the extinction coefficient kG and we quantify its corresponding confidence interval via bootstrap resampling. We tested our method on samples of red giants and main sequence stars, finding consistent solutions. Results: We present here the determination of the Gaia extinction coefficient through a completely empirical method. Furthermore we provide the scientific community with a formula for measuring the extinction coefficient as a function of stellar effective temperature, the intrinsic colour (G - KS)0, and absorption.

Convective Heat Transfer Coefficients of the Human Body under Forced Convection from Ceiling

DEFF Research Database (Denmark)

Kurazumi, Yoshihito; Rezgals, Lauris; Melikov, Arsen Krikor

2014-01-01

The average convective heat transfer coefficient for a seated human body exposed to downward flow from above was determined. Thermal manikin with complex body shape and size of an average Scandinavian female was used. The surface temperature distribution of the manikin’s body was as the skin...... of the convective heat transfer coefficient of the whole body (hc [W/(m2•K)]) was proposed: hc=4.088+6.592V1.715 for a seated naked body at 20ºC and hc=2.874+7.427V1.345 for a seated naked body at 26ºC. Differences in the convective heat transfer coefficient of the whole body in low air velocity range, V

A Semiparametric Time Trend Varying Coefficients Model: With An Application to Evaluate Credit Rationing in U.S. Credit Market

OpenAIRE

Jingping Gu; Paula Hernandez-Verme

2009-01-01

In this paper, we propose a new semiparametric varying coefficient model which extends the existing semi-parametric varying coefficient models to allow for a time trend regressor with smooth coefficient function. We propose to use the local linear method to estimate the coefficient functions and we provide the asymptotic theory to describe the asymptotic distribution of the local linear estimator. We present an application to evaluate credit rationing in the U.S. credit market. Using U.S. mon...

A Semiparametric Time Trend Varying Coefficients Model: With An Application to Evaluate Credit Rationing in U.S. Credit Market

OpenAIRE

Qi Gao; Jingping Gu; Paula Hernandez-Verme

2012-01-01

In this paper, we propose a new semiparametric varying coefficient model which extends the existing semi-parametric varying coefficient models to allow for a time trend regressor with smooth coefficient function. We propose to use the local linear method to estimate the coefficient functions and we provide the asymptotic theory to describe the asymptotic distribution of the local linear estimator. We present an application to evaluate credit rationing in the U.S. credit market. Using U.S. mon...

CFD simulation of simultaneous monotonic cooling and surface heat transfer coefficient

International Nuclear Information System (INIS)

Mihálka, Peter; Matiašovský, Peter

2016-01-01

The monotonic heating regime method for determination of thermal diffusivity is based on the analysis of an unsteady-state (stabilised) thermal process characterised by an independence of the space-time temperature distribution on initial conditions. At the first kind of the monotonic regime a sample of simple geometry is heated / cooled at constant ambient temperature. The determination of thermal diffusivity requires the determination rate of a temperature change and simultaneous determination of the first eigenvalue. According to a characteristic equation the first eigenvalue is a function of the Biot number defined by a surface heat transfer coefficient and thermal conductivity of an analysed material. Knowing the surface heat transfer coefficient and the first eigenvalue the thermal conductivity can be determined. The surface heat transport coefficient during the monotonic regime can be determined by the continuous measurement of long-wave radiation heat flow and the photoelectric measurement of the air refractive index gradient in a boundary layer. CFD simulation of the cooling process was carried out to analyse local convective and radiative heat transfer coefficients more in detail. Influence of ambient air flow was analysed. The obtained eigenvalues and corresponding surface heat transfer coefficient values enable to determine thermal conductivity of the analysed specimen together with its thermal diffusivity during a monotonic heating regime.

THREE-MOMENT BASED APPROXIMATION OF PROBABILITY DISTRIBUTIONS IN QUEUEING SYSTEMS

Directory of Open Access Journals (Sweden)

T. I. Aliev

2014-03-01

Full Text Available The paper deals with the problem of approximation of probability distributions of random variables defined in positive area of real numbers with coefficient of variation different from unity. While using queueing systems as models for computer networks, calculation of characteristics is usually performed at the level of expectation and variance. At the same time, one of the main characteristics of multimedia data transmission quality in computer networks is delay jitter. For jitter calculation the function of packets time delay distribution should be known. It is shown that changing the third moment of distribution of packets delay leads to jitter calculation difference in tens or hundreds of percent, with the same values of the first two moments – expectation value and delay variation coefficient. This means that delay distribution approximation for the calculation of jitter should be performed in accordance with the third moment of delay distribution. For random variables with coefficients of variation greater than unity, iterative approximation algorithm with hyper-exponential two-phase distribution based on three moments of approximated distribution is offered. It is shown that for random variables with coefficients of variation less than unity, the impact of the third moment of distribution becomes negligible, and for approximation of such distributions Erlang distribution with two first moments should be used. This approach gives the possibility to obtain upper bounds for relevant characteristics, particularly, the upper bound of delay jitter.

Recurrence relations between transformation coefficients of hyperspherical harmonics and their application to Moshinsky coefficients

International Nuclear Information System (INIS)

Raynal, J.

1976-01-01

Closed formulae and recurrence relations for the transformation of a two-body harmonic oscillator wave function to the hyperspherical formalism are given. With them Moshinsky or Smirnov coefficients are obtained from the transformation coefficients of hyperspheric harmonics. For these coefficients the diagonalization method of Talman and Lande reduces to simple recurrence relations which can be used directly to compute them. New closed formulae for these coefficients are also derived: they are needed to compute the two simplest coefficients which determine the sign for the recurrence relation. (Auth.)

Microstructural effect on radiative scattering coefficient and asymmetry factor of anisotropic thermal barrier coatings

Science.gov (United States)

Chen, X. W.; Zhao, C. Y.; Wang, B. X.

2018-05-01

Thermal barrier coatings are common porous materials coated on the surface of devices operating under high temperatures and designed for heat insulation. This study presents a comprehensive investigation on the microstructural effect on radiative scattering coefficient and asymmetry factor of anisotropic thermal barrier coatings. Based on the quartet structure generation set algorithm, the finite-difference-time-domain method is applied to calculate angular scattering intensity distribution of complicated random microstructure, which takes wave nature into account. Combining Monte Carlo method with Particle Swarm Optimization, asymmetry factor, scattering coefficient and absorption coefficient are retrieved simultaneously. The retrieved radiative properties are identified with the angular scattering intensity distribution under different pore shapes, which takes dependent scattering and anisotropic pore shape into account implicitly. It has been found that microstructure significantly affects the radiative properties in thermal barrier coatings. Compared with spherical shape, irregular anisotropic pore shape reduces the forward scattering peak. The method used in this paper can also be applied to other porous media, which designs a frame work for further quantitative study on porous media.

Comparison of field-measured radon diffusion coefficients with laboratory-measured coefficients

International Nuclear Information System (INIS)

Lepel, E.A.; Silker, W.B.; Thomas, V.W.; Kalkwarf, D.R.

1983-04-01

Experiments were conducted to compare radon diffusion coefficients determined for 0.1-m depths of soils by a steady-state method in the laboratory and diffusion coefficients evaluated from radon fluxes through several-fold greater depths of the same soils covering uranium-mill tailings. The coefficients referred to diffusion in the total pore volume of the soils and are equivalent to values for the quantity, D/P, in the Generic Environmental Impact Statement on Uranium Milling prepared by the US Nuclear Regulatory Commission. Two soils were tested: a well-graded sand and an inorganic clay of low plasticity. For the flux evaluations, radon was collected by adsorption on charcoal following passive diffusion from the soil surface and also from air recirculating through an aluminum tent over the soil surface. An analysis of variance in the flux evaluations showed no significant difference between these two collection methods. Radon diffusion coefficients evaluated from field data were statistically indistinguishable, at the 95% confidence level, from those measured in the laboratory; however, the low precision of the field data prevented a sensitive validation of the laboratory measurements. From the field data, the coefficients were calculated to be 0.03 +- 0.03 cm 2 /s for the sand cover and 0.0036 +- 0.0004 cm 2 /s for the clay cover. The low precision in the coefficients evaluated from field data was attributed to high variation in radon flux with time and surface location at the field site

Studying the extinction coefficient due to aerosol particles at different spectral bands in some regions at great Cairo

International Nuclear Information System (INIS)

Shaltout, M.A. Mosalam; Tadros, M.T.Y.; El-Metwally, M.

2000-01-01

Extinction coefficient due to aerosol has been estimated by Pyrheliometric and Gorgie type Actinometric measurements in the industrial, urban areas and compared with agricultural areas. The measurements distributed over one year from June 1992 to May 1993 were made under clear sky for five spectral bands. The results show two maxima in hot wet and spring months and minimum in winter months, but there is a fluctuation in urban area. Diurnal variations show maximum at noon especially in the industrial area. Level of extinction coefficient in the industrial and urban area is greater that that of the agricultural area, except for hot wet months is due to the increase of water vapor content in agricultural area. Spectral distribution of the extinction coefficient decreases monotonically with wavelength. Size of particles in industrial area is greater than in urban and agricultural areas. The temperature and water vapor content have important rules in increasing the extinction coefficient of aerosols. (Author)

Soil-soil solution distribution coefficient of soil organic matter is a key factor for that of radioiodide in surface and subsurface soils.

Science.gov (United States)

Unno, Yusuke; Tsukada, Hirofumi; Takeda, Akira; Takaku, Yuichi; Hisamatsu, Shun'ichi

2017-04-01

We investigated the vertical distribution of the soil-soil-solution distribution coefficients (K d ) of 125 I, 137 Cs, and 85 Sr in organic-rich surface soil and organic-poor subsurface soil of a pasture and an urban forest near a spent-nuclear-fuel reprocessing plant in Rokkasho, Japan. K d of 137 Cs was highly correlated with water-extractable K + . K d of 85 Sr was highly correlated with water-extractable Ca 2+ and SOC. K d of 125 I - was low in organic-rich surface soil, high slightly below the surface, and lowest in the deepest soil. This kinked distribution pattern differed from the gradual decrease of the other radionuclides. The thickness of the high- 125 I - K d middle layer (i.e., with high radioiodide retention ability) differed between sites. K d of 125 I - was significantly correlated with K d of soil organic carbon. Our results also showed that the layer thickness is controlled by the ratio of K d -OC between surface and subsurface soils. This finding suggests that the addition of SOC might prevent further radioiodide migration down the soil profile. As far as we know, this is the first report to show a strong correlation of a soil characteristic with K d of 125 I - . Further study is needed to clarify how radioiodide is retained and migrates in soil. Copyright © 2017 Elsevier Ltd. All rights reserved.

An inverse moisture diffusion algorithm for the determination of diffusion coefficient

Science.gov (United States)

Jen Y. Liu; William T. Simpson; Steve P. Verrill

2000-01-01

The finite difference approximation is applied to estimate the moisture-dependent diffusion coefficient by utilizing test data of isothermal moisture desorption in northern red oak (Quercus rubra). The test data contain moisture distributions at discrete locations across the thickness of specimens, which coincides with the radial direction of northern red oak, and at...

A comparison of confidence interval methods for the concordance correlation coefficient and intraclass correlation coefficient with small number of raters.

Science.gov (United States)

Feng, Dai; Svetnik, Vladimir; Coimbra, Alexandre; Baumgartner, Richard

2014-01-01

The intraclass correlation coefficient (ICC) with fixed raters or, equivalently, the concordance correlation coefficient (CCC) for continuous outcomes is a widely accepted aggregate index of agreement in settings with small number of raters. Quantifying the precision of the CCC by constructing its confidence interval (CI) is important in early drug development applications, in particular in qualification of biomarker platforms. In recent years, there have been several new methods proposed for construction of CIs for the CCC, but their comprehensive comparison has not been attempted. The methods consisted of the delta method and jackknifing with and without Fisher's Z-transformation, respectively, and Bayesian methods with vague priors. In this study, we carried out a simulation study, with data simulated from multivariate normal as well as heavier tailed distribution (t-distribution with 5 degrees of freedom), to compare the state-of-the-art methods for assigning CI to the CCC. When the data are normally distributed, the jackknifing with Fisher's Z-transformation (JZ) tended to provide superior coverage and the difference between it and the closest competitor, the Bayesian method with the Jeffreys prior was in general minimal. For the nonnormal data, the jackknife methods, especially the JZ method, provided the coverage probabilities closest to the nominal in contrast to the others which yielded overly liberal coverage. Approaches based upon the delta method and Bayesian method with conjugate prior generally provided slightly narrower intervals and larger lower bounds than others, though this was offset by their poor coverage. Finally, we illustrated the utility of the CIs for the CCC in an example of a wake after sleep onset (WASO) biomarker, which is frequently used in clinical sleep studies of drugs for treatment of insomnia.

Transport coefficients and orientational distributions of dilute colloidal dispersions composed of hematite particles (for an external magnetic field parallel to the angular velocity vector of simple shear flow)

International Nuclear Information System (INIS)

Satoh, Akira; Hayasaka, Ryo; Majima, Tamotsu

2008-01-01

We have treated a dilute dispersion composed of ferromagnetic rodlike particles with a magnetic moment normal to the particle axis, such as hematites, to investigate the influences of the magnetic field strength, shear rate, and random forces on the orientational distribution of rodlike particles and also on transport coefficients, such as viscosity and diffusion coefficient. In the present analysis, these rodlike particles are assumed to conduct the rotational Brownian motion in a simple shear flow as well as an external magnetic field. The results obtained here are summarized as follows. In the case of a strong magnetic field and a smaller shear rate, the rodlike particle can freely rotate in the xy-plane with the magnetic moment continuing to point the magnetic field direction. On the other hand, for a strong shear flow, the particle has a tendency to incline in the flow direction with the magnetic moment pointing to the magnetic field direction. In the case of the magnetic field applied normal to the direction of the sedimentation, the diffusion coefficient gives rise to smaller values than expected, since the rodlike particle sediments with the particle axis inclining toward directions normal to the movement direction and, of course, toward the direction along that direction

Velocity Distributions in Inelastic Granular Gases with Continuous Size Distributions

International Nuclear Information System (INIS)

Li Rui; Li Zhi-Hao; Zhang Duan-Ming

2011-01-01

We study by numerical simulation the property of velocity distributions of granular gases with a power-law size distribution, driven by uniform heating and boundary heating. It is found that the form of velocity distribution is primarily controlled by the restitution coefficient η and q, the ratio between the average number of heatings and the average number of collisions in the system. Furthermore, we show that uniform and boundary heating can be understood as different limits of q, with q ≫ 1 and q ≤ 1, respectively. (general)

Modelling the stochastic nature of the available coefficient of friction at footwear-floor interfaces.

Science.gov (United States)

Gragg, Jared; Klose, Ellison; Yang, James

2017-07-01

The available coefficient of friction (ACOF) is a measure of the friction available between two surfaces, which for human gait would be the footwear-floor interface. It is often compared to the required coefficient of friction (RCOF) to determine the likelihood of a slip in gait. Both the ACOF and RCOF are stochastic by nature meaning that neither should be represented by a deterministic value, such as the sample mean. Previous research has determined that the RCOF can be modelled well by either the normal or lognormal distributions, but previous research aimed at determining an appropriate distribution for the ACOF was inconclusive. This study focuses on modelling the stochastic nature of the ACOF by fitting eight continuous probability distributions to ACOF data for six scenarios. In addition, the data were used to study the effect that a simple housekeeping action such as sweeping could have on the ACOF. Practitioner Summary: Previous research aimed at determining an appropriate distribution for the ACOF was inconclusive. The study addresses this issue as well as looking at the effect that an act such as sweeping has on the ACOF.

Singularities of the transmission coefficient and anomalous scattering by a dielectric slab

Science.gov (United States)

Shestopalov, Yury

2018-03-01

We prove the existence and describe the distribution on the complex plane of the singularities, resonant states (RSs), of the transmission coefficient in the problem of the plane wave scattering by a parallel-plate dielectric slab in free space. It is shown that the transmission coefficient has isolated poles all with nonzero imaginary parts that form countable sets in the complex plane of the refraction index or permittivity of the slab with the only accumulation point at infinity. The transmission coefficient never vanishes and anomalous scattering, when its modulus exceeds unity, occurs at arbitrarily small loss of the dielectric filling the layer. These results are extended to the cases of scattering by arbitrary multi-layer parallel-plane media. Connections are established between RSs, spectral singularities, eigenvalues of the associated Sturm-Liouville problems on the line, and zeros of the corresponding Jost function.

The influence of precipitation kinetics on trace element partitioning between solid and liquid solutions: A coupled fluid dynamics/thermodynamics framework to predict distribution coefficients

Science.gov (United States)

Kavner, A.

2017-12-01

In a multicomponent multiphase geochemical system undergoing a chemical reaction such as precipitation and/or dissolution, the partitioning of species between phases is determined by a combination of thermodynamic properties and transport processes. The interpretation of the observed distribution of trace elements requires models integrating coupled chemistry and mechanical transport. Here, a framework is presented that predicts the kinetic effects on the distribution of species between two reacting phases. Based on a perturbation theory combining Navier-Stokes fluid flow and chemical reactivity, the framework predicts rate-dependent partition coefficients in a variety of different systems. We present the theoretical framework, with applications to two systems: 1. species- and isotope-dependent Soret diffusion of species in a multicomponent silicate melt subjected to a temperature gradient, and 2. Elemental partitioning and isotope fractionation during precipitation of a multicomponent solid from a multicomponent liquid phase. Predictions will be compared with results from experimental studies. The approach has applications for understanding chemical exchange in at boundary layers such as the Earth's surface magmatic systems and at the core/mantle boundary.

Study of the determination method of the river dispersion coefficient

International Nuclear Information System (INIS)

Carvalho, M.A.G. de.

1982-01-01

An application of the method introduced by 'Fischer, H.B. - 1968 - Dispersion prediction in natural streams Journal of the Sanitary Engineering Division, ACSE, vol. 94 n 5A5. Proc. Paper 6169 pp 927-943.', for the calculation of the dispersion coefficient, based on Taylor's model is made. The aim is to develop a method which avoids the necessity of having an instantaneous impulse at the entrance section (1st section) of the system being measured. The dispersion coefficient is determined by curve fitting the experimental response in the 2nd secton and that obtained with the model by means of the non-linear least-squares method. The same method is applied with the residence time distribution function. The theoretical differences between these two function and their results are discussed. By adjusting the two model parameters in all these calculations, the dispersion coefficient and the mean velocity are determined, simultaneously. A comparison between the moment's method and Fischer's formulation is also done using the same experimental data. (E.G.) [pt

Nondestructive hall coefficient measurements using ACPD techniques

Science.gov (United States)

Velicheti, Dheeraj; Nagy, Peter B.; Hassan, Waled

2018-04-01

Hall coefficient measurements offer great opportunities as well as major challenges for nondestructive materials characterization. The Hall effect is produced by the magnetic Lorentz force acting on moving charge carriers in the presence of an applied magnetic field. The magnetic perturbation gives rise to a Hall current that is normal to the conduction current but does not directly perturb the electric potential distribution. Therefore, Hall coefficient measurements usually exploit the so-called transverse galvanomagnetic potential drop effect that arises when the Hall current is intercepted by the boundaries of the specimen and thereby produce a measurable potential drop. In contrast, no Hall potential is produced in a large plate in the presence of a uniform normal field at quasi-static low frequencies. In other words, conventional Hall coefficient measurements are inherently destructive since they require cutting the material under tests. This study investigated the feasibility of using alternating current potential drop (ACPD) techniques for nondestructive Hall coefficient measurements in plates. Specifically, the directional four-point square-electrode configuration is investigated with superimposed external magnetic field. Two methods are suggested to make Hall coefficient measurements in large plates without destructive machining. At low frequencies, constraining the bias magnetic field can replace constraining the dimensions of the specimen, which is inherently destructive. For example, when a cylindrical permanent magnet is used to provide the bias magnetic field, the peak Hall voltage is produced when the diameter of the magnet is equal to the diagonal of the square ACPD probe. Although this method is less effective than cutting the specimen to a finite size, the loss of sensitivity is less than one order of magnitude even at very low frequencies. In contrast, at sufficiently high inspection frequencies the magnetic field of the Hall current induces a

Weyl q-coefficients for uq(3) and Racah q -coefficients for suq(2)

International Nuclear Information System (INIS)

Asherova, R.M.; Smirnov, Yu.F.; Tolstoy, V.N.

1996-01-01

With the aid of the projection-operator technique, the general analytic expression for the elements of the matrix that relates the U and T bases of an arbitrary finite-dimensional irreducible representation of the uq(3) quantum algebra (Weyl q-coefficients) is obtained for the case where the deformation parameter q is not equal to a square root of unity. The procedure for resummation of q-factorial expressions is used to prove that, modulo phase factors, these Weyl q-coefficients coincide with Racah q-coefficients for the suq(2) quantum algebra. It is also shown that, on the basis of one general formula, the q-analogs of all known general analytic expressions for the 6j symbols (and Racah coefficients) of the Lie algebras of the angular momentum can be obtained by using this resummation procedure. The symmetry properties of these q coefficients are discussed. The result is formulated in the following way: the general formulas for the q-6j symbols (Racah q-coefficients) of the suq(2) quantum algebra are obtained from the general formulas for the conventional 6j symbols (Racah coefficients) of the su(2) Lie algebra by replacing directly all factorials with q-factorials, the symmetry properties of the q-6j symbols being completely coincident with the symmetry properties of the conventional 6j symbols

Effective elasticity coefficients of native rocks and consolidated granular matter

International Nuclear Information System (INIS)

Schulz, Beatrix M.; Schulz, Michael

2008-01-01

The elastic coefficients of binary heterogeneous materials, such as several native rock materials or consolidated granular matter will be determined in terms of a perturbation expansion. Furthermore, in order to check the validity of the obtained results, these are compared with numerical investigations using Boole's model of randomly distributed spheres. Finally, we apply the results on several classes of native rocks and consolidated granular materials

Population decay time and distribution of exciton states analyzed by rate equations based on theoretical phononic and electron-collisional rate coefficients

Science.gov (United States)

Oki, Kensuke; Ma, Bei; Ishitani, Yoshihiro

2017-11-01

Population distributions and transition fluxes of the A exciton in bulk GaN are theoretically analyzed using rate equations of states of the principal quantum number n up to 5 and the continuum. These rate equations consist of the terms of radiative, electron-collisional, and phononic processes. The dependence of the rate coefficients on temperature is revealed on the basis of the collisional-radiative model of hydrogen plasma for the electron-collisional processes and theoretical formulation using Fermi's "golden rule" for the phononic processes. The respective effects of the variations in electron, exciton, and lattice temperatures are exhibited. This analysis is a base of the discussion on nonthermal equilibrium states of carrier-exciton-phonon dynamics. It is found that the exciton dissociation is enhanced even below 150 K mainly by the increase in the lattice temperature. When the thermal-equilibrium temperature increases, the population fluxes between the states of n >1 and the continuum become more dominant. Below 20 K, the severe deviation from the Saha-Boltzmann distribution occurs owing to the interband excitation flux being higher than the excitation flux from the 1 S state. The population decay time of the 1 S state at 300 K is more than ten times longer than the recombination lifetime of excitons with kinetic energy but without the upper levels (n >1 and the continuum). This phenomenon is caused by a shift of population distribution to the upper levels. This phonon-exciton-radiation model gives insights into the limitations of conventional analyses such as the ABC model, the Arrhenius plot, the two-level model (n =1 and the continuum), and the neglect of the upper levels.

The Truth About Ballistic Coefficients

OpenAIRE

Courtney, Michael; Courtney, Amy

2007-01-01

The ballistic coefficient of a bullet describes how it slows in flight due to air resistance. This article presents experimental determinations of ballistic coefficients showing that the majority of bullets tested have their previously published ballistic coefficients exaggerated from 5-25% by the bullet manufacturers. These exaggerated ballistic coefficients lead to inaccurate predictions of long range bullet drop, retained energy and wind drift.

Estimating Reaction Rate Coefficients Within a Travel-Time Modeling Framework

Energy Technology Data Exchange (ETDEWEB)

Gong, R [Georgia Institute of Technology; Lu, C [Georgia Institute of Technology; Luo, Jian [Georgia Institute of Technology; Wu, Wei-min [Stanford University; Cheng, H. [Stanford University; Criddle, Craig [Stanford University; Kitanidis, Peter K. [Stanford University; Gu, Baohua [ORNL; Watson, David B [ORNL; Jardine, Philip M [ORNL; Brooks, Scott C [ORNL

2011-03-01

A generalized, efficient, and practical approach based on the travel-time modeling framework is developed to estimate in situ reaction rate coefficients for groundwater remediation in heterogeneous aquifers. The required information for this approach can be obtained by conducting tracer tests with injection of a mixture of conservative and reactive tracers and measurements of both breakthrough curves (BTCs). The conservative BTC is used to infer the travel-time distribution from the injection point to the observation point. For advection-dominant reactive transport with well-mixed reactive species and a constant travel-time distribution, the reactive BTC is obtained by integrating the solutions to advective-reactive transport over the entire travel-time distribution, and then is used in optimization to determine the in situ reaction rate coefficients. By directly working on the conservative and reactive BTCs, this approach avoids costly aquifer characterization and improves the estimation for transport in heterogeneous aquifers which may not be sufficiently described by traditional mechanistic transport models with constant transport parameters. Simplified schemes are proposed for reactive transport with zero-, first-, nth-order, and Michaelis-Menten reactions. The proposed approach is validated by a reactive transport case in a two-dimensional synthetic heterogeneous aquifer and a field-scale bioremediation experiment conducted at Oak Ridge, Tennessee. The field application indicates that ethanol degradation for U(VI)-bioremediation is better approximated by zero-order reaction kinetics than first-order reaction kinetics.

Test of methods for retrospective activity size distribution determination from filter samples

International Nuclear Information System (INIS)

Meisenberg, Oliver; Tschiersch, Jochen

2015-01-01

Determining the activity size distribution of radioactive aerosol particles requires sophisticated and heavy equipment, which makes measurements at large number of sites difficult and expensive. Therefore three methods for a retrospective determination of size distributions from aerosol filter samples in the laboratory were tested for their applicability. Extraction into a carrier liquid with subsequent nebulisation showed size distributions with a slight but correctable bias towards larger diameters compared with the original size distribution. Yields in the order of magnitude of 1% could be achieved. Sonication-assisted extraction into a carrier liquid caused a coagulation mode to appear in the size distribution. Sonication-assisted extraction into the air did not show acceptable results due to small yields. The method of extraction into a carrier liquid without sonication was applied to aerosol samples from Chernobyl in order to calculate inhalation dose coefficients for 137 Cs based on the individual size distribution. The effective dose coefficient is about half of that calculated with a default reference size distribution. - Highlights: • Activity size distributions can be recovered after aerosol sampling on filters. • Extraction into a carrier liquid and subsequent nebulisation is appropriate. • This facilitates the determination of activity size distributions for individuals. • Size distributions from this method can be used for individual dose coefficients. • Dose coefficients were calculated for the workers at the new Chernobyl shelter

The relationship between multilevel models and non-parametric multilevel mixture models: Discrete approximation of intraclass correlation, random coefficient distributions, and residual heteroscedasticity.

Science.gov (United States)

Rights, Jason D; Sterba, Sonya K

2016-11-01

Multilevel data structures are common in the social sciences. Often, such nested data are analysed with multilevel models (MLMs) in which heterogeneity between clusters is modelled by continuously distributed random intercepts and/or slopes. Alternatively, the non-parametric multilevel regression mixture model (NPMM) can accommodate the same nested data structures through discrete latent class variation. The purpose of this article is to delineate analytic relationships between NPMM and MLM parameters that are useful for understanding the indirect interpretation of the NPMM as a non-parametric approximation of the MLM, with relaxed distributional assumptions. We define how seven standard and non-standard MLM specifications can be indirectly approximated by particular NPMM specifications. We provide formulas showing how the NPMM can serve as an approximation of the MLM in terms of intraclass correlation, random coefficient means and (co)variances, heteroscedasticity of residuals at level 1, and heteroscedasticity of residuals at level 2. Further, we discuss how these relationships can be useful in practice. The specific relationships are illustrated with simulated graphical demonstrations, and direct and indirect interpretations of NPMM classes are contrasted. We provide an R function to aid in implementing and visualizing an indirect interpretation of NPMM classes. An empirical example is presented and future directions are discussed. © 2016 The British Psychological Society.

Experimental determination of the distribution coefficient (Kd) of lead and barium in soils of semiarid region of Bahia, Brazil; Determinacao experimental do coeficiente de distribuicao (Kd) de chumbo e bario em solos da regiao semiarida do estado da Bahia

Energy Technology Data Exchange (ETDEWEB)

Santos, Mariana M.; Fernandes, Heloisa H.F; Pontedeiro, Elizabeth M.; Su, Jian, E-mail: mariana@lasme.coppe.ufrj.br, E-mail: heloisa@lasme.coppe.ufrj.br, E-mail: bettinadulley@hotmail.com, E-mail: sujian@lasme.coppe.ufrj.br [Coordenacao dos Programas de Pos-Graduacao em Engenharia (COOPE/UFRJ), Rio de Janeiro, RJ (Brazil). Lab. de Simulacao e Metodos em Engenharia

2013-07-01

To determine the concentration of heavy metals and other contaminants in soils, aimed at evaluating the environmental impact, the use of the distribution coefficient is required (Kd), defined as the relationship between the concentrations adsorbed and in solution. The objective of this study was to determine the rates for the Lead and Barium metals in soil collected in Caetite, the state of Bahia, in two different depths. The importance of determining the distribution coefficient lies in the fact that being performed using a tropical soil. For the isotherms of Kd was used batch test method by adsorption to obtain the final concentrations. The first step was to determine the best ratio soil: solution obtained after equilibration time and finally the equilibrium concentration of the contaminant. Were also calculated percentages of the metal adsorbed by the soil and the amount of solute by the adsorbent. With the values obtained in experiments and using Mathematica 8.0 software, were made graphics equilibrium concentration versus quantity adsorbed (C vs. S). It can also plot isotherms for different models of Kd: linear, Langmuir and Freundlich in order to determine which adsorption model would fit best to the measured data and thus determine the distribution coefficient of the metal in the soil analyzed. The Freundlich isotherm was better adapted to the points of the two metals in both soils.

Quantitative Analysis of Isolated Single-Wall Carbon Nanotubes with Their Molar Absorbance Coefficients

Directory of Open Access Journals (Sweden)

Shota Kuwahara

2014-01-01

Full Text Available The molar absorbance coefficients of metallic, semiconducting, and (6,5 chirality enriched single-wall carbon nanotubes were evaluated by a spray technique combined with atomic force microscopy. Single-wall carbon nanotubes with isolated and a single predominant electronic type were obtained by using the density-gradient ultracentrifugation technique. In the visible region, all coefficients had similar values around 2–5 × 109/mL mol−1 cm−1, independent of their diameter distribution and the electronic types of single-wall carbon nanotubes, and the εS22/εM11  and εS11/εM11 were estimated to be 1.0 and 4.0, respectively. The coefficient strongly depends on the length of single-wall carbon nanotubes, independent of their electronic types and chirality.

Goodness-of-fit tests for the Gompertz distribution

DEFF Research Database (Denmark)

Lenart, Adam; Missov, Trifon

The Gompertz distribution is often fitted to lifespan data, however testing whether the fit satisfies theoretical criteria was neglected. Here five goodness-of-fit measures, the Anderson-Darling statistic, the Kullback-Leibler discrimination information, the correlation coefficient test, testing ...... for the mean of the sample hazard and a nested test against the generalized extreme value distributions are discussed. Along with an application to laboratory rat data, critical values calculated by the empirical distribution of the test statistics are also presented.......The Gompertz distribution is often fitted to lifespan data, however testing whether the fit satisfies theoretical criteria was neglected. Here five goodness-of-fit measures, the Anderson-Darling statistic, the Kullback-Leibler discrimination information, the correlation coefficient test, testing...

SO-FDTD method and its application to the calculation of electromagnetic wave reflection coefficients of plasma

International Nuclear Information System (INIS)

Yang Hongwei; Nanjing Agricultural Univ., Nanjing; Chen Rushan; Zhang Yun

2006-01-01

The dielectric property of dispersive media is written as rational polynomial function, the relation between D and E is derived in time domain. It is named shift operator FDTD (SO-FDTD) method. The high accuracy and efficiency of this method is confirmed by computing the reflection coefficients of electromagnetic waves by a collisional plasma slab. The reflection coefficients between plasma and the atmosphere or vacuum can be calculated by using the SO-FDTD method. The result is that the reflection coefficients are affected by plasma thickness, electron numerical density, the distributing orderliness of electron density, and incidence wave frequency. (authors)

Reconstruction of emission coefficients for a non-axisymmetric coupling arc by algebraic reconstruction technique

International Nuclear Information System (INIS)

Zhang Guangjun; Xiong Jun; Gao Hongming; Wu Lin

2011-01-01

A preliminary investigation of tomographic reconstruction of an asymmetric arc plasma has been carried out. The objective of this work aims at reconstructing emission coefficients of a non-axisymmetric coupling arc from measured intensities by means of an algebraic reconstruction technique (ART). In order to define the optimal experimental scheme for good quality with limited views, the dependence of the reconstruction quality on three configurations (four, eight, ten projection angles) are presented and discussed via a displaced Gaussian model. Then, the emission coefficients of a free burning arc are reconstructed by the ART with the ten-view configuration and an Abel inversion, respectively, and good agreement is obtained. Finally, the emission coefficient profiles of the coupling arc are successfully achieved with the ten-view configuration. The results show that the distribution of emission coefficient for the coupling arc is different from centrosymmetric shape. The ART is perfectly suitable for reconstructing emission coefficients of the coupling arc with the ten-view configuration, proving the feasibility and utility of the ART to characterize an asymmetric arc.

The Determinants of Gini Coefficient in Iran Based on Bayesian Model Averaging

Directory of Open Access Journals (Sweden)

Mohsen Mehrara

2015-03-01

Full Text Available This paper has tried to apply BMA approach in order to investigate important influential variables on Gini coefficient in Iran over the period 1976-2010. The results indicate that the GDP growth is the most important variable affecting the Gini coefficient and has a positive influence on it. Also the second and third effective variables on Gini coefficient are respectively the ratio of government current expenditure to GDP and the ratio of oil revenue to GDP which lead to an increase in inequality. This result is corresponding with rentier state theory in Iran economy. Injection of massive oil revenue to Iran's economy and its high share of the state budget leads to inefficient government spending and an increase in rent-seeking activities in the country. Economic growth is possibly a result of oil revenue in Iran economy which has caused inequality in distribution of income.

The HD+ dissociative recombination rate coefficient at low temperature

Directory of Open Access Journals (Sweden)

Wolf A.

2015-01-01

Full Text Available The effect of the rotational temperature of the ions is considered for low-energy dissociative recombination (DR of HD+. Merged beams measurements with HD+ ions of a rotational temperature near 300 K are compared to multichannel quantum defect theory calculations. The thermal DR rate coefficient for a Maxwellian electron velocity distribution is derived from the merged-beams data and compared to theoretical results for a range of rotational temperatures. Good agreement is found for the theory with 300 K rotational temperature. For a low-temperature plasma environment where also the rotational temperature assumes 10 K, theory predicts a considerably higher thermal DR rate coefficient. The origin of this is traced to predicted resonant structures of the collision-energy dependent DR cross section at few-meV collision energies for the particular case of HD+ ions in the rotational ground state.

Extending the Constant Coefficient Solution Technique to Variable Coefficient Ordinary Differential Equations

Science.gov (United States)

Mohammed, Ahmed; Zeleke, Aklilu

2015-01-01

We introduce a class of second-order ordinary differential equations (ODEs) with variable coefficients whose closed-form solutions can be obtained by the same method used to solve ODEs with constant coefficients. General solutions for the homogeneous case are discussed.

Precise predictions for the angular coefficients in Z-boson production at the LHC

Science.gov (United States)

Gauld, R.; Gehrmann-De Ridder, A.; Gehrmann, T.; Glover, E. W. N.; Huss, A.

2017-11-01

The angular distributions of lepton pairs in the Drell-Yan process can provide rich information on the underlying QCD production mechanisms. These dynamics can be parameterised in terms of a set of frame dependent angular coefficients, A i=0,…,7, which depend on the invariant mass, transverse momentum, and rapidity of the lepton pair. Motivated by recent measurements of these coefficients by ATLAS and CMS, and in particular by the apparent violation of the Lam-Tung relation A 0 - A 2 = 0, we perform a precision study of the angular coefficients at O({α}s^3) in perturbative QCD. We make predic-tions relevant for pp collisions at √{s}=8 TeV, and perform comparisons with the available ATLAS and CMS data as well as providing predictions for a prospective measurement at LHCb. To expose the violation of the Lam-Tung relationship we propose a new observable ΔLT = 1 - A 2 /A 0 that is more sensitive to the dynamics in the region where A 0 and A 2 are both small. We find that the O({α}s^3) corrections have an important impact on the p T,Z distributions for several of the angular coefficients, and are essential to provide an adequate description of the data. The compatibility of the available ATLAS and CMS data is reassessed by performing a partial χ 2 test with respect to the central theoretical prediction which shows that χ 2 /N data is significantly reduced by going from O({α}s^2) to O({α}s^3).

Prediction of Sliding Friction Coefficient Based on a Novel Hybrid Molecular-Mechanical Model.

Science.gov (United States)

Zhang, Xiaogang; Zhang, Yali; Wang, Jianmei; Sheng, Chenxing; Li, Zhixiong

2018-08-01

Sliding friction is a complex phenomenon which arises from the mechanical and molecular interactions of asperities when examined in a microscale. To reveal and further understand the effects of micro scaled mechanical and molecular components of friction coefficient on overall frictional behavior, a hybrid molecular-mechanical model is developed to investigate the effects of main factors, including different loads and surface roughness values, on the sliding friction coefficient in a boundary lubrication condition. Numerical modelling was conducted using a deterministic contact model and based on the molecular-mechanical theory of friction. In the contact model, with given external loads and surface topographies, the pressure distribution, real contact area, and elastic/plastic deformation of each single asperity contact were calculated. Then asperity friction coefficient was predicted by the sum of mechanical and molecular components of friction coefficient. The mechanical component was mainly determined by the contact width and elastic/plastic deformation, and the molecular component was estimated as a function of the contact area and interfacial shear stress. Numerical results were compared with experimental results and a good agreement was obtained. The model was then used to predict friction coefficients in different operating and surface conditions. Numerical results explain why applied load has a minimum effect on the friction coefficients. They also provide insight into the effect of surface roughness on the mechanical and molecular components of friction coefficients. It is revealed that the mechanical component dominates the friction coefficient when the surface roughness is large (Rq > 0.2 μm), while the friction coefficient is mainly determined by the molecular component when the surface is relatively smooth (Rq < 0.2 μm). Furthermore, optimal roughness values for minimizing the friction coefficient are recommended.

On the velocity distributions of granular gases

International Nuclear Information System (INIS)

Polito, A.M.M.; Rocha Filho, T.M.; Figueiredo, A.

2009-01-01

We present a new approach to determine velocity distributions in granular gases to improve the Sonine polynomial expansion of the velocity distribution function, at higher inelasticities, for the homogeneous cooling regime of inelastic hard spheres. The perturbative consistency is recovered using a new set of dynamical variables based on the characteristic function and we illustrate our approach by computing the first four Sonine coefficients for moderate and high inelasticities. The analytical coefficients are compared with molecular dynamics simulations results and with a previous approach by Huthmann et al.

On the Kendall Correlation Coefficient

OpenAIRE

Stepanov, Alexei

2015-01-01

In the present paper, we first discuss the Kendall rank correlation coefficient. In continuous case, we define the Kendall rank correlation coefficient in terms of the concomitants of order statistics, find the expected value of the Kendall rank correlation coefficient and show that the later is free of n. We also prove that in continuous case the Kendall correlation coefficient converges in probability to its expected value. We then propose to consider the expected value of the Kendall rank ...

The κ-generalized distribution: A new descriptive model for the size distribution of incomes

Science.gov (United States)

Clementi, F.; Di Matteo, T.; Gallegati, M.; Kaniadakis, G.

2008-05-01

This paper proposes the κ-generalized distribution as a model for describing the distribution and dispersion of income within a population. Formulas for the shape, moments and standard tools for inequality measurement-such as the Lorenz curve and the Gini coefficient-are given. A method for parameter estimation is also discussed. The model is shown to fit extremely well the data on personal income distribution in Australia and in the United States.

Hybrid Modeling of Intra-DCT Coefficients for Real-Time Video Encoding

Directory of Open Access Journals (Sweden)

Li Jin

2008-01-01

Full Text Available Abstract The two-dimensional discrete cosine transform (2-D DCT and its subsequent quantization are widely used in standard video encoders. However, since most DCT coefficients become zeros after quantization, a number of redundant computations are performed. This paper proposes a hybrid statistical model used to predict the zeroquantized DCT (ZQDCT coefficients for intratransform and to achieve better real-time performance. First, each pixel block at the input of DCT is decomposed into a series of mean values and a residual block. Subsequently, a statistical model based on Gaussian distribution is used to predict the ZQDCT coefficients of the residual block. Then, a sufficient condition under which each quantized coefficient becomes zero is derived from the mean values. Finally, a hybrid model to speed up the DCT and quantization calculations is proposed. Experimental results show that the proposed model can reduce more redundant computations and achieve better real-time performance than the reference in the literature at the cost of negligible video quality degradation. Experiments also show that the proposed model significantly reduces multiplications for DCT and quantization. This is particularly suitable for processors in portable devices where multiplications consume more power than additions. Computational reduction implies longer battery lifetime and energy economy.

Correlation coefficients in neutron β-decay

International Nuclear Information System (INIS)

Byrne, J.

1978-01-01

The various angular and polarisation coefficients in neutron decay are the principal sources of information on the β-interaction. Measurements of the electron-neutrino angular correlation coefficient (a), the neutron-spin-electron-momentum correlation coefficient (A), the neutron-spin-neutrino-momentum correlation coefficient (B), and the triple correlation coefficient D and time-reversal invariance are reviewed and the results discussed. (U.K.)

On the Diffusion Coefficient of Two-step Method for LWR analysis

International Nuclear Information System (INIS)

Lee, Deokjung; Choi, Sooyoung; Smith, Kord S.

2015-01-01

The few-group constants including diffusion coefficients are generated from the assembly calculation results. Once the assembly calculation is done, the cross sections (XSs) are spatially homogenized, and a critical spectrum calculation is performed in order to take into account the neutron leakages of the lattice. The diffusion coefficient is also generated through the critical spectrum calculation. Three different methods of the critical spectrum calculation such as B1 method, P1 method, and fundamental mode (FM) calculation method are considered in this paper. The diffusion coefficients can also be affected by transport approximations for the transport XS calculation which is used in the assembly transport lattice calculation in order to account for the anisotropic scattering effects. The outflow transport approximation and the inflow transport approximation are investigated in this paper. The accuracy of the few group data especially the diffusion coefficients has been studied to optimize the combination of the transport correction methods and the critical spectrum calculation methods using the UNIST lattice physics code STREAM. The combination of the inflow transport approximation and the FM method is shown to provide the highest accuracy in the LWR core calculations. The methodologies to calculate the diffusion coefficients have been reviewed, and the performances of them have been investigated with a LWR core problem. The combination of the inflow transport approximation and the fundamental mode critical spectrum calculation shows the smallest errors in terms of assembly power distribution

The use of photon correlation spectroscopy method for determining diffusion coefficient in brine and herring flesh

Directory of Open Access Journals (Sweden)

Shumanova M.V.

2015-03-01

Full Text Available The process fish salting has been studied by the method of photon correlation spectroscopy; the distribution of salt concentration in the solution and herring flesh with skin has been found, diffusion coefficients and salt concentrations used for creating a mathematical model of the salting technology have been worked out; the possibility of determination by this method the coefficient of dynamic viscosity of solutions and different media (minced meat etc. has been considered

A Bayesian Framework for Estimating the Concordance Correlation Coefficient Using Skew-elliptical Distributions.

Science.gov (United States)

Feng, Dai; Baumgartner, Richard; Svetnik, Vladimir

2018-04-05

The concordance correlation coefficient (CCC) is a widely used scaled index in the study of agreement. In this article, we propose estimating the CCC by a unified Bayesian framework that can (1) accommodate symmetric or asymmetric and light- or heavy-tailed data; (2) select model from several candidates; and (3) address other issues frequently encountered in practice such as confounding covariates and missing data. The performance of the proposal was studied and demonstrated using simulated as well as real-life biomarker data from a clinical study of an insomnia drug. The implementation of the proposal is accessible through a package in the Comprehensive R Archive Network.

On the Use of Fine Distributed Moderating Material to Enhance Feedback Coefficients in Fast Reactors

International Nuclear Information System (INIS)

Merk, B.

2012-01-01

Conclusions and outlook: • Use of moderating material to enhance feedback coefficients in SFR: • Creation of a new degree of freedom for SFR design; • Good opportunities for the compensation of the effects due to transmutation fuels; • No major influence on Am incinieration; • Major problem is the thermal stability; • Stability up to ~1300°C by use of YH

Using the Coefficient of Determination "R"[superscript 2] to Test the Significance of Multiple Linear Regression

Science.gov (United States)

Quinino, Roberto C.; Reis, Edna A.; Bessegato, Lupercio F.

2013-01-01

This article proposes the use of the coefficient of determination as a statistic for hypothesis testing in multiple linear regression based on distributions acquired by beta sampling. (Contains 3 figures.)

Photon dose conversion coefficients for the human teeth in standard irradiation geometries

Energy Technology Data Exchange (ETDEWEB)

Ulanovsky, A; Wieser, A; Zankl, M; Jacob, P

2005-07-01

Photon dose conversion coefficients for the human tooth materials are computed in energy range from 0.01 to 10 MeV by the Monte Carlo method. The voxel phantom Golem of the human body with newly defined tooth region and a modified version of the EGS4 code have been used to compute the coefficients for 30 tooth cells with different locations and materials. The dose responses are calculated for cells representing buccal and lingual enamel layers. The computed coefficients demonstrate a strong dependence on energy and geometry of the radiation source and a weaker dependence on location of the enamel voxels. For isotropic and rotational radiation fields the enamel dose does not show a significant dependence on tooth sample locations. The computed coefficients are used to convert from absorbed dose in teeth to organ dose or to integral air kerma. Examples of integral conversion factors from enamel dose to air kerma are given for several photon fluences specific for the Mayak reprocessing plant in Russia. The integral conversion factors are strongly affected by the energy and angular distributions of photon fluence, which are important characteristics of an exposure scenario for reconstruction of individual occupational doses. (orig.)

SAMPL5: 3D-RISM partition coefficient calculations with partial molar volume corrections and solute conformational sampling

Science.gov (United States)

Luchko, Tyler; Blinov, Nikolay; Limon, Garrett C.; Joyce, Kevin P.; Kovalenko, Andriy

2016-11-01

Implicit solvent methods for classical molecular modeling are frequently used to provide fast, physics-based hydration free energies of macromolecules. Less commonly considered is the transferability of these methods to other solvents. The Statistical Assessment of Modeling of Proteins and Ligands 5 (SAMPL5) distribution coefficient dataset and the accompanying explicit solvent partition coefficient reference calculations provide a direct test of solvent model transferability. Here we use the 3D reference interaction site model (3D-RISM) statistical-mechanical solvation theory, with a well tested water model and a new united atom cyclohexane model, to calculate partition coefficients for the SAMPL5 dataset. The cyclohexane model performed well in training and testing (R=0.98 for amino acid neutral side chain analogues) but only if a parameterized solvation free energy correction was used. In contrast, the same protocol, using single solute conformations, performed poorly on the SAMPL5 dataset, obtaining R=0.73 compared to the reference partition coefficients, likely due to the much larger solute sizes. Including solute conformational sampling through molecular dynamics coupled with 3D-RISM (MD/3D-RISM) improved agreement with the reference calculation to R=0.93. Since our initial calculations only considered partition coefficients and not distribution coefficients, solute sampling provided little benefit comparing against experiment, where ionized and tautomer states are more important. Applying a simple pK_{ {a}} correction improved agreement with experiment from R=0.54 to R=0.66, despite a small number of outliers. Better agreement is possible by accounting for tautomers and improving the ionization correction.

SAMPL5: 3D-RISM partition coefficient calculations with partial molar volume corrections and solute conformational sampling.

Science.gov (United States)

Luchko, Tyler; Blinov, Nikolay; Limon, Garrett C; Joyce, Kevin P; Kovalenko, Andriy

2016-11-01

Implicit solvent methods for classical molecular modeling are frequently used to provide fast, physics-based hydration free energies of macromolecules. Less commonly considered is the transferability of these methods to other solvents. The Statistical Assessment of Modeling of Proteins and Ligands 5 (SAMPL5) distribution coefficient dataset and the accompanying explicit solvent partition coefficient reference calculations provide a direct test of solvent model transferability. Here we use the 3D reference interaction site model (3D-RISM) statistical-mechanical solvation theory, with a well tested water model and a new united atom cyclohexane model, to calculate partition coefficients for the SAMPL5 dataset. The cyclohexane model performed well in training and testing ([Formula: see text] for amino acid neutral side chain analogues) but only if a parameterized solvation free energy correction was used. In contrast, the same protocol, using single solute conformations, performed poorly on the SAMPL5 dataset, obtaining [Formula: see text] compared to the reference partition coefficients, likely due to the much larger solute sizes. Including solute conformational sampling through molecular dynamics coupled with 3D-RISM (MD/3D-RISM) improved agreement with the reference calculation to [Formula: see text]. Since our initial calculations only considered partition coefficients and not distribution coefficients, solute sampling provided little benefit comparing against experiment, where ionized and tautomer states are more important. Applying a simple [Formula: see text] correction improved agreement with experiment from [Formula: see text] to [Formula: see text], despite a small number of outliers. Better agreement is possible by accounting for tautomers and improving the ionization correction.

Estimating temperature reactivity coefficients by experimental procedures combined with isothermal temperature coefficient measurements and dynamic identification

International Nuclear Information System (INIS)

Tsuji, Masashi; Aoki, Yukinori; Shimazu, Yoichiro; Yamasaki, Masatoshi; Hanayama, Yasushi

2006-01-01

A method to evaluate the moderator coefficient (MTC) and the Doppler coefficient through experimental procedures performed during reactor physics tests of PWR power plants is proposed. This method combines isothermal temperature coefficient (ITC) measurement experiments and reactor power transient experiments at low power conditions for dynamic identification. In the dynamic identification, either one of temperature coefficients can be determined in such a way that frequency response characteristics of the reactivity change observed by a digital reactivity meter is reproduced from measured data of neutron count rate and the average coolant temperature. The other unknown coefficient can also be determined by subtracting the coefficient obtained from the dynamic identification from ITC. As the proposed method can directly estimate the Doppler coefficient, the applicability of the conventional core design codes to predict the Doppler coefficient can be verified for new types of fuels such as mixed oxide fuels. The digital simulation study was carried out to show the feasibility of the proposed method. The numerical analysis showed that the MTC and the Doppler coefficient can be estimated accurately and even if there are uncertainties in the parameters of the reactor kinetics model, the accuracies of the estimated values are not seriously impaired. (author)

Research on friction coefficient of nuclear Reactor Vessel Internals Hold Down Spring: Stress coefficient test analysis method

International Nuclear Information System (INIS)

Linjun, Xie; Guohong, Xue; Ming, Zhang

2016-01-01

Graphical abstract: HDS stress coefficient test apparatus. - Highlights: • This paper performs mathematic deduction to the physical model of Hold Down Spring (HDS), establishes a mathematic model of axial load P and stress, stress coefficient and friction coefficient and designs a set of test apparatuses for simulating the pretightening process of the HDS for the first time according to a model similarity criterion. • The mathematical relation between the load and the strain is obtained about the HDS, and the mathematical model of the stress coefficient and the friction coefficient is established. So, a set of test apparatuses for obtaining the stress coefficient is designed according to the model scaling criterion and the friction coefficient of the K1000 HDS is calculated to be 0.336 through the obtained stress coefficient. • The relation curve between the theoretical load and the friction coefficient is obtained through analysis and indicates that the change of the friction coefficient f would influence the pretightening load under the condition of designed stress. The necessary pretightening load in the design process is calculated to be 5469 kN according to the obtained friction coefficient. Therefore, the friction coefficient and the pretightening load under the design conditions can provide accurate pretightening data for the analysis and design of the reactor HDS according to the operations. - Abstract: This paper performs mathematic deduction to the physical model of Hold Down Spring (HDS), establishes a mathematic model of axial load P and stress, stress coefficient and friction coefficient and designs a set of test apparatuses for simulating the pretightening process of the HDS for the first time according to a model similarity criterion. By carrying out tests and researches through a stress testing technique, P–σ curves in loading and unloading processes of the HDS are obtained and the stress coefficient k f of the HDS is obtained. So, the

Research on friction coefficient of nuclear Reactor Vessel Internals Hold Down Spring: Stress coefficient test analysis method

Energy Technology Data Exchange (ETDEWEB)

Linjun, Xie, E-mail: linjunx@zjut.edu.cn [College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310014 (China); Guohong, Xue; Ming, Zhang [Shanghai Nuclear Engineering Research & Design Institute, Shanghai 200233 (China)

2016-08-01

Graphical abstract: HDS stress coefficient test apparatus. - Highlights: • This paper performs mathematic deduction to the physical model of Hold Down Spring (HDS), establishes a mathematic model of axial load P and stress, stress coefficient and friction coefficient and designs a set of test apparatuses for simulating the pretightening process of the HDS for the first time according to a model similarity criterion. • The mathematical relation between the load and the strain is obtained about the HDS, and the mathematical model of the stress coefficient and the friction coefficient is established. So, a set of test apparatuses for obtaining the stress coefficient is designed according to the model scaling criterion and the friction coefficient of the K1000 HDS is calculated to be 0.336 through the obtained stress coefficient. • The relation curve between the theoretical load and the friction coefficient is obtained through analysis and indicates that the change of the friction coefficient f would influence the pretightening load under the condition of designed stress. The necessary pretightening load in the design process is calculated to be 5469 kN according to the obtained friction coefficient. Therefore, the friction coefficient and the pretightening load under the design conditions can provide accurate pretightening data for the analysis and design of the reactor HDS according to the operations. - Abstract: This paper performs mathematic deduction to the physical model of Hold Down Spring (HDS), establishes a mathematic model of axial load P and stress, stress coefficient and friction coefficient and designs a set of test apparatuses for simulating the pretightening process of the HDS for the first time according to a model similarity criterion. By carrying out tests and researches through a stress testing technique, P–σ curves in loading and unloading processes of the HDS are obtained and the stress coefficient k{sub f} of the HDS is obtained. So, the

DETERMINATION EXPERIMENTALE DU COEFFICIENT DE DISPERSION D’UNE MATRICE DE SOL

Directory of Open Access Journals (Sweden)

R MAOUI

2005-06-01

Full Text Available La caractérisation des interactions entre une espèce chimique et une matrice de sol est généralement considérée dans les études des phénomènes de transport. Ce type de réaction est assujetti à l’estimation du coefficient de dispersion D. Ce coefficient représente le gradient de concentration de l’élément et le flux de transport ; il dépend de la distribution de la vitesse, de la porosité du milieu et des courants du liquide. Le présent travail décrit le procédé expérimental et la technique associée utilisés en vue de quantifier le coefficient D de deux traceurs radioactifs. Les résultats obtenus à l’échelle du laboratoire sont très satisfaisants et restent en conformité avec les résultats publiés

Dose Rate and Mass Attenuation Coefficients of Gamma Ray for Concretes

CERN Document Server

Abdel-Latif, A A; Kansouh, W A; El-Sayed, F H

2003-01-01

This work is concerned with the study of the leakage gamma ray dose and mass attenuation coefficients for ordinary, basalt and dolomite concretes made from local ores. Concretes under investigation were constructed from gravel, basalt and dolomite ores, and then reconstructed with the addition of 3% steel fibers by weight. Measurements were carried out using a collimated beam from sup 6 sup 0 Co gamma ray source and sodium iodide (3x3) crystal with the genie 2000 gamma spectrometer. The obtained fluxes were transformed to gamma ray doses and displayed in the form of gamma ray dose rates distribution. The displayed curves were used to estimate the linear attenuation coefficients (mu), the relaxation lengths (lambda), half value layer (t sub 1 /2) and tenth value layer (t sub 1 /10). Also, The total mass attenuation coefficients of gamma ray have been calculated to the concerned concretes using XCOM (version 3.1) program and database elements cross sections from Z=1 to 100 at energies from 10 keV to 100 MeV. In...

Permeability and Dispersion Coefficients in Rocks with Fracture Network - 12140

Energy Technology Data Exchange (ETDEWEB)

Lee, C.K.; Htway, M.Z. [Handong Global University, 3 Namsong-ri, Heunghae-eub, Buk-gu, Pohang, Kyungbuk, 791-708 (Korea, Republic of); Yim, S.P. [Korea Atomic Energy Research Institute, P.O.Box 150, Yusong, Daejon, 305-600 (Korea, Republic of)

2012-07-01

Fluid flow and solute transport are considered for a rock medium with a fracture network with regard to the effective permeability and the dispersion coefficients. To investigate the effects of individual fractures a three-fracture system is chosen in which two are parallel and the third one connects the two at different angles. Specifically the micro-cell boundary-value problems(defined through multiple scale analysis) are solved numerically by using finite elements to calculate the permeability and dispersion coefficients. It is shown that the permeability depends significantly on the pattern of the fracture distribution and the dispersion coefficient is influenced by both the externally imposed pressure gradient (which also reflects the flow field) and the direction of the gradient of solute concentration on the macro-scale. From the calculations of the permeability and dispersion coefficients for solute in a rock medium with a fracture network the following conclusions are drawn. 1. The permeability of fractured medium depends on the primary orientation of the fracture network and is influenced by the connecting fractures in the medium. 2. The cross permeability, e.g., permeability in the direction normal to the direction of the external pressure gradient is rather insensitive to the orientation of the fracture network. 3. Calculation of permeability is most efficiently achieved with optimal discretization across individual fractures and is rather insensitive to the discretization along the fracture.. 4. The longitudinal dispersion coefficient Dxx of a fractured medium depends on both the macro-scale concentration gradient and the direction of the flow (pressure gradient). Hence both features must be considered when investigating solute transport in a fractured medium. (authors)

Measuring of heat transfer coefficient

DEFF Research Database (Denmark)

Henningsen, Poul; Lindegren, Maria

Subtask 3.4 Measuring of heat transfer coefficient Subtask 3.4.1 Design and setting up of tests to measure heat transfer coefficient Objective: Complementary testing methods together with the relevant experimental equipment are to be designed by the two partners involved in order to measure...... the heat transfer coefficient for a wide range of interface conditions in hot and warm forging processes. Subtask 3.4.2 Measurement of heat transfer coefficient The objective of subtask 3.4.2 is to determine heat transfer values for different interface conditions reflecting those typically operating in hot...

Clustering Coefficients for Correlation Networks

Directory of Open Access Journals (Sweden)

Naoki Masuda

2018-03-01

Full Text Available Graph theory is a useful tool for deciphering structural and functional networks of the brain on various spatial and temporal scales. The clustering coefficient quantifies the abundance of connected triangles in a network and is a major descriptive statistics of networks. For example, it finds an application in the assessment of small-worldness of brain networks, which is affected by attentional and cognitive conditions, age, psychiatric disorders and so forth. However, it remains unclear how the clustering coefficient should be measured in a correlation-based network, which is among major representations of brain networks. In the present article, we propose clustering coefficients tailored to correlation matrices. The key idea is to use three-way partial correlation or partial mutual information to measure the strength of the association between the two neighboring nodes of a focal node relative to the amount of pseudo-correlation expected from indirect paths between the nodes. Our method avoids the difficulties of previous applications of clustering coefficient (and other measures in defining correlational networks, i.e., thresholding on the correlation value, discarding of negative correlation values, the pseudo-correlation problem and full partial correlation matrices whose estimation is computationally difficult. For proof of concept, we apply the proposed clustering coefficient measures to functional magnetic resonance imaging data obtained from healthy participants of various ages and compare them with conventional clustering coefficients. We show that the clustering coefficients decline with the age. The proposed clustering coefficients are more strongly correlated with age than the conventional ones are. We also show that the local variants of the proposed clustering coefficients (i.e., abundance of triangles around a focal node are useful in characterizing individual nodes. In contrast, the conventional local clustering coefficients

Clustering Coefficients for Correlation Networks.

Science.gov (United States)

Masuda, Naoki; Sakaki, Michiko; Ezaki, Takahiro; Watanabe, Takamitsu

2018-01-01

Graph theory is a useful tool for deciphering structural and functional networks of the brain on various spatial and temporal scales. The clustering coefficient quantifies the abundance of connected triangles in a network and is a major descriptive statistics of networks. For example, it finds an application in the assessment of small-worldness of brain networks, which is affected by attentional and cognitive conditions, age, psychiatric disorders and so forth. However, it remains unclear how the clustering coefficient should be measured in a correlation-based network, which is among major representations of brain networks. In the present article, we propose clustering coefficients tailored to correlation matrices. The key idea is to use three-way partial correlation or partial mutual information to measure the strength of the association between the two neighboring nodes of a focal node relative to the amount of pseudo-correlation expected from indirect paths between the nodes. Our method avoids the difficulties of previous applications of clustering coefficient (and other) measures in defining correlational networks, i.e., thresholding on the correlation value, discarding of negative correlation values, the pseudo-correlation problem and full partial correlation matrices whose estimation is computationally difficult. For proof of concept, we apply the proposed clustering coefficient measures to functional magnetic resonance imaging data obtained from healthy participants of various ages and compare them with conventional clustering coefficients. We show that the clustering coefficients decline with the age. The proposed clustering coefficients are more strongly correlated with age than the conventional ones are. We also show that the local variants of the proposed clustering coefficients (i.e., abundance of triangles around a focal node) are useful in characterizing individual nodes. In contrast, the conventional local clustering coefficients were strongly

Clustering Coefficients for Correlation Networks

Science.gov (United States)

Masuda, Naoki; Sakaki, Michiko; Ezaki, Takahiro; Watanabe, Takamitsu

2018-01-01

Graph theory is a useful tool for deciphering structural and functional networks of the brain on various spatial and temporal scales. The clustering coefficient quantifies the abundance of connected triangles in a network and is a major descriptive statistics of networks. For example, it finds an application in the assessment of small-worldness of brain networks, which is affected by attentional and cognitive conditions, age, psychiatric disorders and so forth. However, it remains unclear how the clustering coefficient should be measured in a correlation-based network, which is among major representations of brain networks. In the present article, we propose clustering coefficients tailored to correlation matrices. The key idea is to use three-way partial correlation or partial mutual information to measure the strength of the association between the two neighboring nodes of a focal node relative to the amount of pseudo-correlation expected from indirect paths between the nodes. Our method avoids the difficulties of previous applications of clustering coefficient (and other) measures in defining correlational networks, i.e., thresholding on the correlation value, discarding of negative correlation values, the pseudo-correlation problem and full partial correlation matrices whose estimation is computationally difficult. For proof of concept, we apply the proposed clustering coefficient measures to functional magnetic resonance imaging data obtained from healthy participants of various ages and compare them with conventional clustering coefficients. We show that the clustering coefficients decline with the age. The proposed clustering coefficients are more strongly correlated with age than the conventional ones are. We also show that the local variants of the proposed clustering coefficients (i.e., abundance of triangles around a focal node) are useful in characterizing individual nodes. In contrast, the conventional local clustering coefficients were strongly

Size effects on the transport coefficient of liquid lithium, sodium and potassium using a soft sphere potential

International Nuclear Information System (INIS)

Adebayo, G.A.; Anusionwu, B.C.

2004-08-01

The dependence of the self diffusion coefficient of atoms in liquid Lithium, Sodium and Potassium, interacting through a soft sphere potential, on the number of atoms have been investigated using Molecular Dynamics Simulation at various temperatures. Our calculations predict non-linear relationship between the diffusion coefficient and the number of particles at high densities and medium or low temperatures. The radial distribution function obtained agrees well with experiment. (author)

Form of multicomponent Fickian diffusion coefficients matrix

International Nuclear Information System (INIS)

Wambui Mutoru, J.; Firoozabadi, Abbas

2011-01-01

Highlights: → Irreversible thermodynamics establishes form of multicomponent diffusion coefficients. → Phenomenological coefficients and thermodynamic factors affect sign of diffusion coefficients. → Negative diagonal elements of diffusion coefficients matrix can occur in non-ideal mixtures. → Eigenvalues of the matrix of Fickian diffusion coefficients may not be all real. - Abstract: The form of multicomponent Fickian diffusion coefficients matrix in thermodynamically stable mixtures is established based on the form of phenomenological coefficients and thermodynamic factors. While phenomenological coefficients form a symmetric positive definite matrix, the determinant of thermodynamic factors matrix is positive. As a result, the Fickian diffusion coefficients matrix has a positive determinant, but its elements - including diagonal elements - can be negative. Comprehensive survey of reported diffusion coefficients data for ternary and quaternary mixtures, confirms that invariably the determinant of the Fickian diffusion coefficients matrix is positive.

Mechanical Safety Subcommittee Guideline for Design of Thin Windows Regarding Roark’s Edge Condition Coefficient

Energy Technology Data Exchange (ETDEWEB)

Ader, C. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Voirin, E. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); McGee, M. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States); Nobrega, L. [Fermi National Accelerator Lab. (FNAL), Batavia, IL (United States)

2017-06-15

An error was found in an edge stress coefficient used to calculate stresses in thin windows. This error is present in “Roark’s Formulas for Stress and Strain” 7th and 8th Edition. The 6th Edition is correct. This guideline specially discusses a major difference in regards to a coefficient used in calculating the edge stress in “Roark’s Formulas for Stress and Strain” 6th Edition compared to the 7th and 8th Editions. In Chapter 10: Flat Plates under “Circular plates under distributed load producing large deflections,” Case 3, which is “Fixed and held. Uniform pressure q over entire plate.” The coefficient for a fixed edge condition in the 6th Edition1 K4 = 0.476 while in the 7th and 8th Edition2, the coefficient is 1.73 which is significant difference.

Sample Size Calculation for Estimating or Testing a Nonzero Squared Multiple Correlation Coefficient

Science.gov (United States)

Krishnamoorthy, K.; Xia, Yanping

2008-01-01

The problems of hypothesis testing and interval estimation of the squared multiple correlation coefficient of a multivariate normal distribution are considered. It is shown that available one-sided tests are uniformly most powerful, and the one-sided confidence intervals are uniformly most accurate. An exact method of calculating sample size to…

Theoretical treatment of equilibrium data and evaluation of diffusion coefficients in extraction of uranium

Energy Technology Data Exchange (ETDEWEB)

Manohar, Smitha; Theyyunni, T K [Process Engineering and Systems Development Division, Bhabha Atomic Research Centre, Mumbai (India); Ragunathan, T S [Department of Chemical Engineering, Indian Inst. of Tech., Mumbai (India)

1994-06-01

A meaningful approach to the calculation of the performance of solvent extraction contactors in the PUREX process requires a good understanding of the equilibrium distribution of the important constituents, namely uranyl nitrate and nitric acid. Published literature refers to the empirical correlation of the distribution data, generally in the form of polynomials. Attempts are made to describe the distribution data in a form which is specially convenient for numerical computations along with its theoretical significance. Attempts are also made to derive suitable equations which would aid in estimation of diffusion coefficients in the uranyl nitrate-nitric acid-TBP/diluent system. (author). 2 tabs.

The effect of changing seawater Ca and Mg concentrations upon the distribution coefficients of Mg and Sr in the skeletons of the scleractinian coral Pocillopora damicornis

Science.gov (United States)

Giri, Sharmila J.; Swart, Peter K.; Devlin, Quinn B.

2018-02-01

The skeletal composition of calcifying organisms, in particular Mg/Ca and Sr/Ca ratios, have been widely used to understand fluctuations in seawater chemistry throughout the Phanerozoic. While the success of applying these data to the geologic record depends on a knowledge of the distribution coefficients for these elements (DMg and DSr), there are scarcely any studies which have described how these values vary as a result of changing seawater Mg/Ca ratios. To address this, we have cultured the scleractinian coral, Pocillopora damicornis, in seawater with ranges of Mg and Ca concentrations. Here, we demonstrate that Mg/Ca and Sr/Ca ratios of coral skeletons correlate with total seawater Mg/Ca and Sr/Ca molar ratios, but that apparent DMg and DSr values do not remain constant across the range of experimental seawater treatments, with DMg values significantly increasing with seawater Mg/Ca ratios and DSr values significantly increasing with seawater Ca concentrations. These trends are not rate dependent and may be best explained by a Rayleigh distillation model, in which the calcifying space is semi-isolated from seawater during skeletogenesis (i.e. leaky). As there is a slight increase in DMg and decrease in DSr values between our "Jurassic" and "Modern" seawater treatments, the application of a constant distribution coefficient to estimate changes in ancient seawater chemistry may underestimate seawater Mg/Ca ratios and overestimate Sr/Ca throughout the Mesozoic and Cenozoic. We suggest that interpretations of seawater chemistry from fossil corals may be improved by using the relationships derived for skeletal and seawater Mg/Ca and Sr/Ca ratios established by our experiments, as they incorporate the effect of seawater Mg/Ca ratios on skeletal Mg/Ca and Sr/Ca ratios.

Rayleigh Pareto Distribution

Directory of Open Access Journals (Sweden)

Kareema ‎ Abed Al-Kadim

2017-12-01

Full Text Available In this paper Rayleigh Pareto distribution have  introduced denote by( R_PD. We stated some  useful functions. Therefor  we  give some of its properties like the entropy function, mean, mode, median , variance , the r-th moment about the mean, the rth moment about the origin, reliability, hazard functions, coefficients of variation, of sekeness and of kurtosis. Finally, we estimate the parameters  so the aim of this search  is to introduce a new distribution

Extensive Investigations on Bio-Inspired Trust and Reputation Model over Hops Coefficient Factor in Distributed Wireless Sensor Networks

Directory of Open Access Journals (Sweden)

Vinod Kumar Verma

2014-08-01

Full Text Available Resource utilization requires a substantial consideration for a trust and reputation model to be deployed within a wireless sensor network (WSN. In the evaluation, our attention is focused on the effect of hops coefficient factor estimation on WSN with bio-inspired trust and reputation model (BTRM. We present the state-of-the-art system level evaluation of accuracy and path length of sensor node operations for their current and average scenarios. Additionally, we emphasized over the energy consumption evaluation for static, dynamic and oscillatory modes of BTRM-WSN model. The performance of the hops coefficient factor for our proposed framework is evaluated via analytic bounds and numerical simulations.

Reliability Estimation of Aero-engine Based on Mixed Weibull Distribution Model

Science.gov (United States)

Yuan, Zhongda; Deng, Junxiang; Wang, Dawei

2018-02-01

Aero-engine is a complex mechanical electronic system, based on analysis of reliability of mechanical electronic system, Weibull distribution model has an irreplaceable role. Till now, only two-parameter Weibull distribution model and three-parameter Weibull distribution are widely used. Due to diversity of engine failure modes, there is a big error with single Weibull distribution model. By contrast, a variety of engine failure modes can be taken into account with mixed Weibull distribution model, so it is a good statistical analysis model. Except the concept of dynamic weight coefficient, in order to make reliability estimation result more accurately, three-parameter correlation coefficient optimization method is applied to enhance Weibull distribution model, thus precision of mixed distribution reliability model is improved greatly. All of these are advantageous to popularize Weibull distribution model in engineering applications.

Evaluating Residence Time for Cesium Removal from Simulated Hanford Tank Wastes Using SuperLig(R) 644 Resin

International Nuclear Information System (INIS)

Hassan, N.M.

2003-01-01

Batch contact and column experiments were performed to evaluate the effect of residence time on cesium (Cs) removal from two simulated Hanford tank wastes using SuperLig(R) 644 resin. The two waste simulants mimic the compositions of tanks 241-AZ-102 and 241-AN-107 at the U.S. Department of Energy (DOE) Hanford site. A single column made of glass tube (2.7-cm i.d.), which contained approximately 100 mL of H-form SuperLig(R) 644 resin was used in the column experiments. The experiments each consisted of loading, elution, and regeneration steps were performed at flow rates ranging from 0.64 to 8.2 BV/h for AZ-102 and from 1.5 to 18 BV/h for AN-107 simulant. The lowest flow rates of 0.64 and 1.5 BV/h were selected to evaluate less than optimal flow conditions in the plant. The range of the flow rates is consistent with the River Protection Project design for the waste treatment plant (WTP) columns, which will operate at a flow rate between 1.5 to 3 BV/h. Batch contact experiments were also performed for two batches of SuperLig(R) 644 to determine the equilibrium distribution coefficients (Kds) as a function of Cs concentration

Geochemical effects on the behavior of LLW radionuclides in soil/groundwater environments

Energy Technology Data Exchange (ETDEWEB)

Krupka, K.M.; Sterne, R.J. [Pacific Northwest Lab., Richland, WA (United States)

1995-12-31

Assessing the migration potential of radionuclides leached from low-level radioactive waste (LLW) and decommissioning sites necessitates information on the effects of sorption and precipitation on the concentrations of dissolved radionuclides. Such an assessment requires that the geochemical processes of aqueous speciation, complexation, oxidation/reduction, and ion exchange be taken into account. The Pacific Northwest National Laboratory (PNNL) is providing technical support to the U.S. Nuclear Regulatory Commission (NRC) for defining the solubility and sorption behavior of radionuclides in soil/ground-water environments associated with engineered cementitious LLW disposal systems and decommissioning sites. Geochemical modeling is being used to predict solubility limits for radionuclides under geochemical conditions associated with these environments. The solubility limits are being used as maximum concentration limits in performance assessment calculations describing the release of contaminants from waste sources. Available data were compiled regarding the sorption potential of radionuclides onto {open_quotes}fresh{close_quotes} cement/concrete where the expected pH of the cement pore waters will equal to or exceed 10. Based on information gleaned from the literature, a list of preferred minimum distribution coefficients (Kd`s) was developed for these radionuclides. The K{sub d} values are specific to the chemical environments associated with the evolution of the compositions of cement/concrete pore waters.

Angular distribution and rotations of frame in vector meson decays into lepton pairs

International Nuclear Information System (INIS)

Palestini, Sandro

2011-01-01

We discuss how the angular distribution of lepton pairs from decays of vector mesons depends on the choice of reference frame, and provide a geometrical description of the transformations of the coefficients of the angular distribution. Invariant expressions involving all coefficients are discussed, together with bounds and consistency relations.

Diffusion coefficients of Fokker-Planck equation for rotating dust grains in a fusion plasma

Science.gov (United States)

Bakhtiyari-Ramezani, M.; Mahmoodi, J.; Alinejad, N.

2015-11-01

In the fusion devices, ions, H atoms, and H2 molecules collide with dust grains and exert stochastic torques which lead to small variations in angular momentum of the grain. By considering adsorption of the colliding particles, thermal desorption of H atoms and normal H2 molecules, and desorption of the recombined H2 molecules from the surface of an oblate spheroidal grain, we obtain diffusion coefficients of the Fokker-Planck equation for the distribution function of fluctuating angular momentum. Torque coefficients corresponding to the recombination mechanism show that the nonspherical dust grains may rotate with a suprathermal angular velocity.

Electron excitation coefficients of neutral and ionic levels of krypton in Townsend discharges

International Nuclear Information System (INIS)

Malovic, G.N.; Strinic, A.I.; Petrovic, Z.Lj.; Sadeghi, N.

2006-01-01

In this paper, we present experimental results for excitation coefficients of krypton atoms to several Kr and Kr + excited levels for E/N (electric field to gas particle number density ratio usually in units of Townsend, 1 Td = 10 -21 V m 2 ) values from 7 x 10 -20 V m 2 to above 1 x 10 -17 V m 2 . The data have been obtained in two different parallel plate self-sustained Townsend discharge drift tubes. The spatial distribution of the emission intensities were recorded and then normalized to give excitation coefficients at the anode, by using the electron flux at this point. The values of these coefficients are placed on an absolute scale by using a standard tungsten ribbon lamp calibrated against a primary blackbody radiation standard. The ionization rates at different E/N are obtained from the spatial emission profiles. The data for atomic krypton levels 2p 2 , 2p 3 , 2p 5 , 2p 6 , 2p 7 , 2p 8 , 3p 5 and 3p 6 (in Paschen notation) were converted to excitation coefficients by using quenching coefficients from the literature. The emission coefficients of eight 4s 2 4p 4 ( 3 P)5p levels of Kr + have also been measured for E/N values from about 1 x 10 -18 V m 2 up to nearly 8 x 10 -18 V m 2

A Pareto upper tail for capital income distribution

Science.gov (United States)

Oancea, Bogdan; Pirjol, Dan; Andrei, Tudorel

2018-02-01

We present a study of the capital income distribution and of its contribution to the total income (capital income share) using individual tax income data in Romania, for 2013 and 2014. Using a parametric representation we show that the capital income is Pareto distributed in the upper tail, with a Pareto coefficient α ∼ 1 . 44 which is much smaller than the corresponding coefficient for wage- and non-wage-income (excluding capital income), of α ∼ 2 . 53. Including the capital income contribution has the effect of increasing the overall inequality measures.

Sabine absorption coefficients to random incidence absorption coefficients

DEFF Research Database (Denmark)

Jeong, Cheol-Ho

2014-01-01

into random incidence absorption coefficients for porous absorbers are investigated. Two optimization-based conversion methods are suggested: the surface impedance estimation for locally reacting absorbers and the flow resistivity estimation for extendedly reacting absorbers. The suggested conversion methods...

Banded Structures in Electron Pitch Angle Diffusion Coefficients from Resonant Wave Particle Interactions

Science.gov (United States)

Tripathi, A. K.; Singhal, R. P.; Khazanov, G. V.; Avanov, L. A.

2016-01-01

Electron pitch angle (D (alpha)) and momentum (D(pp)) diffusion coefficients have been calculated due to resonant interactions with electrostatic electron cyclotron harmonic (ECH) and whistler mode chorus waves. Calculations have been performed at two spatial locations L = 4.6 and 6.8 for electron energies 10 keV. Landau (n = 0) resonance and cyclotron harmonic resonances n = +/-1, +/-2,...+/-5 have been included in the calculations. It is found that diffusion coefficient versus pitch angle (alpha) profiles show large dips and oscillations or banded structures. The structures are more pronounced for ECH and lower band chorus (LBC) and particularly at location 4.6. Calculations of diffusion coefficients have also been performed for individual resonances. It is noticed that the main contribution of ECH waves in pitch angle diffusion coefficient is due to resonances n = +1 and n = +2. A major contribution to momentum diffusion coefficients appears from n = +2. However, the banded structures in D alpha and Dpp coefficients appear only in the profile of diffusion coefficients for n = +2. The contribution of other resonances to diffusion coefficients is found to be, in general, quite small or even negligible. For LBC and upper band chorus waves, the banded structures appear only in Landau resonance. The Dpp diffusion coefficient for ECH waves is one to two orders smaller than D alpha coefficients. For chorus waves, Dpp coefficients are about an order of magnitude smaller than D alpha coefficients for the case n does not = 0. In case of Landau resonance, the values of Dpp coefficient are generally larger than the values of D alpha coefficients particularly at lower energies. As an aid to the interpretation of results, we have also determined the resonant frequencies. For ECH waves, resonant frequencies have been estimated for wave normal angle 89 deg and harmonic resonances n = +1, +2, and +3, whereas for whistler mode waves, the frequencies have been calculated for angle

A comparative radiological assessment of five European biosphere systems in the context of potential contamination of well water from the hypothetical disposal of radioactive waste.

Science.gov (United States)

Olyslaegers, G; Zeevaert, T; Pinedo, P; Simon, I; Pröhl, G; Kowe, R; Chen, Q; Mobbs, S; Bergström, U; Hallberg, B; Katona, T; Eged, K; Kanyar, B

2005-12-01

In the framework of the BioMoSA project for the development of biosphere assessment models for radioactive waste disposal the Reference Biosphere Methodology developed in the IAEA programme BIOMASS was applied to five locations, situated in different European countries. Specific biosphere models were applied to assess the hypothetical contamination of a range of agricultural and environmental pathways and the dose to individuals, following contamination of well water. The results of these site-specific models developed by the different BioMoSA partners, and the individual normalised dose to the exposure groups were compared against each other. Ingestion of drinking water, fruit and vegetables were found to be among the most important pathways for almost all radionuclides. Stochastic calculations revealed that consumption habits, transfer factors, irrigation rates and distribution coefficients (Kd(s)) were the most important parameters that influence the end results. Variations in the confidence intervals were found to be higher for sorbing elements (e.g. (36)Cl, (237)Np, (99)Tc, (238)U, (129)I) than for mobile elements (e.g. (226)Ra, (79)Se, (135)Cs, (231)Pa, (239)Pu). The influence of daughter products, for which the distribution into the biosphere was calculated individually, was also shown to be important. This paper gives a brief overview of the deterministic and stochastic modelling results and the parameter sensitivity. A screening methodology was introduced to identify the most important pathways, simplify a generic biosphere tool and refine the existing models.

Transport Coefficients of Fluids

CERN Document Server

Eu, Byung Chan

2006-01-01

Until recently the formal statistical mechanical approach offered no practicable method for computing the transport coefficients of liquids, and so most practitioners had to resort to empirical fitting formulas. This has now changed, as demonstrated in this innovative monograph. The author presents and applies new methods based on statistical mechanics for calculating the transport coefficients of simple and complex liquids over wide ranges of density and temperature. These molecular theories enable the transport coefficients to be calculated in terms of equilibrium thermodynamic properties, and the results are shown to account satisfactorily for experimental observations, including even the non-Newtonian behavior of fluids far from equilibrium.

Dicty_cDB: SHL271 [Dicty_cDB

Lifescience Database Archive (English)

Full Text Available *tl*eiksnrc*sfiih**wlcnwfglylkiirsk*rfrfsslvrsysiem *n*skenvg*skckryqrgsksfsn*kds...*stfkeflyhrtclglkl hrsydq**r*tl*eiksnrc*sfiih**wlcnwfglylkiirsk*rfrfsslvrsysiem *n*skenvg*skckryqrgsksfsn*kd

Influence of water vapour on the height distribution of positive ions, effective recombination coefficient and ionisation balance in the quiet lower ionosphere

Directory of Open Access Journals (Sweden)

V. Barabash

2014-03-01

vapour concentration upper limit at altitudes between 75 and 87 km, beyond which the water vapour concentration ceases to influence the numerical densities of Cl2+ and Cl1+, the effective recombination coefficient and the electron number density in the summer ionosphere. This water vapour concentration limit corresponds to values found in the H2O-1 profile that was observed in the summer mesosphere by the Upper Atmosphere Research Satellite (UARS. The electron density modelled using the H2O-1 profile agreed well with the electron density measured in the summer ionosphere when the measured profiles did not have sharp gradients. For sharp gradients in electron and positive ion number densities, a water profile that can reproduce the characteristic behaviour of the ionospheric parameters should have an inhomogeneous height distribution of water vapour.

Energy coefficients for a propeller series

DEFF Research Database (Denmark)

Olsen, Anders Smærup

2004-01-01

The efficiency for a propeller is calculated by energy coefficients. These coefficients are related to four types of losses, i.e. the axial, the rotational, the frictional, and the finite blade number loss, and one gain, i.e. the axial gain. The energy coefficients are derived by use...... of the potential theory with the propeller modelled as an actuator disk. The efficiency based on the energy coefficients is calculated for a propeller series. The results show a good agreement between the efficiency based on the energy coefficients and the efficiency obtained by a vortex-lattice method....

A drying coefficient for building materials

DEFF Research Database (Denmark)

Scheffler, Gregor Albrecht; Plagge, Rudolf

2009-01-01

coefficient is defined which can be determined based on measured drying data. The correlation of this coefficient with the water absorption and the vapour diffusion coefficient is analyzed and its additional information content is critically challenged. As result, a drying coefficient has been derived......The drying experiment is an important element of the hygrothermal characterisation of building materials. Contrary to other moisture transport experiments as the vapour diffusion and the water absorption test, it is until now not possible to derive a simple coefficient for the drying. However......, in many cases such a coefficient would be highly appreciated, e.g. in interaction of industry and research or for the distinction and selection of suitable building materials throughout design and practise. This article first highlights the importance of drying experiments for hygrothermal...

Zero Distribution of System with Unknown Random Variables Case Study: Avoiding Collision Path

Directory of Open Access Journals (Sweden)

Parman Setyamartana

2014-07-01

Full Text Available This paper presents the stochastic analysis of finding the feasible trajectories of robotics arm motion at obstacle surrounding. Unknown variables are coefficients of polynomials joint angle so that the collision-free motion is achieved. ãk is matrix consisting of these unknown feasible polynomial coefficients. The pattern of feasible polynomial in the obstacle environment shows as random. This paper proposes to model the pattern of this randomness values using random polynomial with unknown variables as coefficients. The behavior of the system will be obtained from zero distribution as the characteristic of such random polynomial. Results show that the pattern of random polynomial of avoiding collision can be constructed from zero distribution. Zero distribution is like building block of the system with obstacles as uncertainty factor. By scale factor k, which has range, the random coefficient pattern can be predicted.

Materials analysis using x-ray linear attenuation coefficient measurements at four photon energies

International Nuclear Information System (INIS)

Midgley, S M

2005-01-01

The analytical properties of an accurate parameterization scheme for the x-ray linear attenuation coefficient are examined. The parameterization utilizes an additive combination of N compositional- and energy-dependent coefficients. The former were derived from a parameterization of elemental cross-sections using a polynomial in atomic number. The compositional-dependent coefficients are referred to as the mixture parameters, representing the electron density and higher order statistical moments describing elemental distribution. Additivity is an important property of the parameterization, allowing measured x-ray linear attenuation coefficients to be written as linear simultaneous equations, and then solved for the unknown coefficients. The energy-dependent coefficients can be determined by calibration from measurements with materials of known composition. The inverse problem may be utilized for materials analysis, whereby the simultaneous equations represent multi-energy linear attenuation coefficient measurements, and are solved for the mixture parameters. For in vivo studies, the choice of measurement energies is restricted to the diagnostic region (approximately 20 keV to 150 keV), where the parameterization requires N ≥ 4 energies. We identify a mathematical pathology that must be overcome in order to solve the inverse problem in this energy regime. An iterative inversion strategy is presented for materials analysis using four or more measurements, and then tested against real data obtained at energies 32 keV to 66 keV. The results demonstrate that it is possible to recover the electron density to within ±4% and fourth mixture parameter. It is also a key finding that the second and third mixture parameters cannot be recovered, as they are of minor importance in the parameterization at diagnostic x-ray energies

Invar hardening under keeping of low values of temperature coefficient of linear expansion

International Nuclear Information System (INIS)

Bashnin, Yu.A.; Shiryaeva, A.N.; Omel'chenko, A.V.

1982-01-01

Complex invar alloying with chromium, zirconium and nitrogen is conducted for increasing hardness and assuring low values of the temperature coefficient of linear expansion. It is shown that alloying with nitride-forming elements-chromium, zirconium and the following high-temperature saturation under high pressure with nitrogen provides the invar hardening at assuring a low temperature coefficient of linear expansion. Saturation with nitrogen under 100 MPa pressure at 1050 deg C during 3 hours permits to prepare an invar containing up to 0.2% N 2 uniformly distributed over the whole cross section of samples with 4 mm diameter. Nitrogen in invar alloys alloyed with chromium and zirconium affects the Curie point similarly to carbon and nickel shifting it towards higher temperatures, it slightly changes the value of the temperature coefficient of linear expansion and provides linear character of thermal expansion dependence on temperature in the +100 deg C - -180 deg C range

Negative Correlation between the Diffusion Coefficient and Transcriptional Activity of the Glucocorticoid Receptor.

Science.gov (United States)

Mikuni, Shintaro; Yamamoto, Johtaro; Horio, Takashi; Kinjo, Masataka

2017-08-25

The glucocorticoid receptor (GR) is a transcription factor, which interacts with DNA and other cofactors to regulate gene transcription. Binding to other partners in the cell nucleus alters the diffusion properties of GR. Raster image correlation spectroscopy (RICS) was applied to quantitatively characterize the diffusion properties of EGFP labeled human GR (EGFP-hGR) and its mutants in the cell nucleus. RICS is an image correlation technique that evaluates the spatial distribution of the diffusion coefficient as a diffusion map. Interestingly, we observed that the averaged diffusion coefficient of EGFP-hGR strongly and negatively correlated with its transcriptional activities in comparison to that of EGFP-hGR wild type and mutants with various transcriptional activities. This result suggests that the decreasing of the diffusion coefficient of hGR was reflected in the high-affinity binding to DNA. Moreover, the hyper-phosphorylation of hGR can enhance the transcriptional activity by reduction of the interaction between the hGR and the nuclear corepressors.

Influence on Heat Transfer Coefficient of Heat Exchanger by Velocity and Heat Transfer Temperature Difference

Directory of Open Access Journals (Sweden)

WANG Fang

2017-04-01

Full Text Available Aimed to insufficient heat transfer of heat exchanger, research the influence on the heat transfer coefficient impacted by velocity and heat transfer temperature difference of tube heat exchanger. According to the different heat transfer temperature difference and gas velocity，the experimental data were divided into group. Using the control variable method，the above two factors were analyzed separately. K一△T and k一:fitting curve were clone to obtain empirical function. The entire heat exchanger is as the study object，using numerical simulation methods，porous media，k一￡model，second order upwind mode，and pressure一velocity coupling with SIMPLE algorithm，the entire heat exchanger temperature field and the heat transfer coefficient distribution were given. Finally the trend of the heat transfer coefficient effected by the above two factors was gotten.

Determination of dispersion coefficients in the River Plate

International Nuclear Information System (INIS)

Maggio, G.E.; Graino, J.G.; Kopp, U.I.; Tripoli, C.R.

1987-01-01

The determination of dispersion coefficients of contaminants through a radioactive tracer was performed as a contribution to the development of a mathematical model for a zone of the River Plate, close to the effluent discharge. During March 1987, six operations of tracer (I-131) injection and follow-up were carried out. The injection was performed by breaking a bulb under water and the follow-up of the 'radioactive spot' was done by means of a boat. Once the 'radioactive spot' was located (approximately 2 hours after the injection) a series of transversal movements over it was effected, measuring the activity concentration by means of a submerged detector. At the same time the coordinates of each point were determined in order to draw a map of the activity distribution. This procedure was repeated for different spot positions. This set of data can be plotted on a map of the zone under study, so as to obtain a set of iso activity curves. However, these curves would be representative provided that corrections are made for the boat speed, the water speed and the half-life of radionuclide. From each set of iso activity curves, the variance and the increase of variance, as well as the dispersion coefficients, can be determined. This procedure was applied to each one of the six above mentioned operations. Presently, different values of dispersion coefficient are available for different river conditions. These values, together with other parameters, such as wind velocity, temperature, salinity, bacterial behaviour, etc., will allow the calibration of the mathematical model. (Author)

Compilation report of VHTRC temperature coefficient benchmark calculations

Energy Technology Data Exchange (ETDEWEB)

Yasuda, Hideshi; Yamane, Tsuyoshi [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1995-11-01

A calculational benchmark problem has been proposed by JAERI to an IAEA Coordinated Research Program, `Verification of Safety Related Neutronic Calculation for Low-enriched Gas-cooled Reactors` to investigate the accuracy of calculation results obtained by using codes of the participating countries. This benchmark is made on the basis of assembly heating experiments at a pin-in block type critical assembly, VHTRC. Requested calculation items are the cell parameters, effective multiplication factor, temperature coefficient of reactivity, reaction rates, fission rate distribution, etc. Seven institutions from five countries have joined the benchmark works. Calculation results are summarized in this report with some remarks by the authors. Each institute analyzed the problem by applying the calculation code system which was prepared for the HTGR development of individual country. The values of the most important parameter, k{sub eff}, by all institutes showed good agreement with each other and with the experimental ones within 1%. The temperature coefficient agreed within 13%. The values of several cell parameters calculated by several institutes did not agree with the other`s ones. It will be necessary to check the calculation conditions again for getting better agreement. (J.P.N.).

Recovery coefficients as a test of system linearity of response in PET

International Nuclear Information System (INIS)

Geworski, L.; Munz, D.L.; Knoop, B.; Hofmann, M.; Knapp, W.H.

2002-01-01

Aim: New imaging protocols have created an increasing demand for quantitation in dedicated PET. Besides attenuation and scatter correction the recovery correction, accounting for the instrument's limited spatial resolution, has gained importance. For clinical practicability these corrections should work independent from the object, i.e. from the actual distribution of emitter and absorber. Aim of the study was to test this object independency, i.e. system linearity of response, by comparing recovery coefficients (RC) determined for different object geometries. In fact, this comparison may serve as a final test on system linearity of response, as measured on the quantitative accuracy by which the activity concentration in small lesions can be recovered. Method: For hot and cold spot imaging situations spatial distribution of activity is different. Therefore, scatter correction algorithm has to deal with different scatter distributions. If all factors disturbing system linearity, specifically scatter and attenuation, are corrected to a sufficient degree of accuracy, the system behaves linearly resulting in the theoretical relationship. CSRC = (1-HSRC). Thus, this equation, applied hot and cold spot measurements, will serve as a test on the effectiveness of the corrections and, hence, as a test of system linearity of response. Following IEC standard procedures (IEC 61675-1) measurements were done with and without interplane septa (2D/3D) on an ECAT EXACT 922 using a cylindrical phantom containing six spheres of different diameters (10 mm - 40 mm). All data were corrected for attenuation (transmission scan) and scatter (2D: deconvolution, 3D: scatter model), as implemented in the scanner's standard software. Recovery coefficients were determined for cold (CSRC) and hot (HSRC) lesions using both 2D and 3D acquisition mode. Results: CSRC directly measured versus CSRC calculated according to eq. (1) from HSRC resulted in an excellent agreement for both 2D and 3D data

Partial differential equations II elements of the modern theory equations with constant coefficients

CERN Document Server

Shubin, M

1994-01-01

This book, the first printing of which was published as Volume 31 of the Encyclopaedia of Mathematical Sciences, contains a survey of the modern theory of general linear partial differential equations and a detailed review of equations with constant coefficients. Readers will be interested in an introduction to microlocal analysis and its applications including singular integral operators, pseudodifferential operators, Fourier integral operators and wavefronts, a survey of the most important results about the mixed problem for hyperbolic equations, a review of asymptotic methods including short wave asymptotics, the Maslov canonical operator and spectral asymptotics, a detailed description of the applications of distribution theory to partial differential equations with constant coefficients including numerous interesting special topics.

Turbid Media Extinction Coefficient for Near-Infrared Laser Radiation

International Nuclear Information System (INIS)

Dreischuh, T; Gurdev, L; Vankov, O; Stoyanov, D; Avramov, L

2015-01-01

In this work, extended investigations are performed of the extinction coefficient of Intralipid-20% dilutions in distilled water depending on the Intralipid concentration, for laser radiation wavelengths in the red and near-infrared regions covering the so-called tissue optical window. The extinction is measured by using an approach we have developed recently based on the features of the spatial intensity distribution of laser-radiation beams propagating through semi-infinite turbid media. The measurements are conducted using separately two dilution- containing plexiglass boxes of different sizes and volumes, in order to prove the appropriateness of the assumption of semi-infinite turbid medium. The experimental results for the extinction are in agreement with our previous results and with empiric formulae found by other authors concerning the wavelength dependence of the scattering coefficient of Intralipid – 10% and Intralipid – 20%. They are also in agreement with known data of the water absorptance. It is estimated as well that the wavelengths around 1320 nm would be advantageous for deep harmless sensing and diagnostics of tissues

Isolation of Salmonella typhimurium strains that utilize exogenous 3-deoxy-D-manno-Octulosonate for synthesis of lipopolysaccharide

International Nuclear Information System (INIS)

Goldman, R.C.; Devine, E.M.

1987-01-01

Spontaneous mutants of Salmonella typhimurium LT2 were selected for the ability to accumulate exogenous 3-deoxy-D-manno-octulosonate (KDO). Bacteria containing a gene (kdsA) which codes for a temperature-sensitive KDO-8-phosphate synthetase were plated at the restrictive temperature of 42 0 C on medium containing 5 mM KDO. Since bacteria containing the kdsA lesion are unable to grown at 42 0 C due to inhibition of lipopolysaccharide (LPS) synthesis and accumulation of lipid A precursor, this method allowed direct, positive selection of mutants capable of utilizing exogenous KDO for LPS synthesis. Spontaneous mutants, selected at a frequency of about 10 -6 , required exogenous KDO for growth at 42 0 C. The growth rate at 42 0 C was nearly normal in the presence of 20 mM KDO and was directly proportional to KDO concentrations below 20 mM. Exogenous KDO also suppressed accumulation of lipid A precursor. The apparent K/sub m/ for KDO accumulation was 23 mM, and the maximum rate of transport was calculated to be 505 pmol of DKO per min per 10 8 cells. Bacteria incorporated exogenous [ 3 H]KDO exclusively into LPS, with less that 10% dilution in specific activity due to residual endogenous KDO synthesis. The mutation giving rise to the ability to accumulate exogenous KDO was extremely useful in the direct screening for new mutations in the kdsA gene after localized mutagenesis. Five mutations in kdsA were isolated, four of which were new alleles as determined by on fine-structure analysis. The ability to introduce labeled ( 3 H, 13 C, and 14 C) KDO in vivo should simplify and extend the analysis of this critical metabolic pathway in gram-negative bacteria

Quadrature formulas for Fourier coefficients

KAUST Repository

Bojanov, Borislav

2009-09-01

We consider quadrature formulas of high degree of precision for the computation of the Fourier coefficients in expansions of functions with respect to a system of orthogonal polynomials. In particular, we show the uniqueness of a multiple node formula for the Fourier-Tchebycheff coefficients given by Micchelli and Sharma and construct new Gaussian formulas for the Fourier coefficients of a function, based on the values of the function and its derivatives. © 2009 Elsevier B.V. All rights reserved.

Computational error estimates for Monte Carlo finite element approximation with log normal diffusion coefficients

KAUST Repository

Sandberg, Mattias

2015-01-07

The Monte Carlo (and Multi-level Monte Carlo) finite element method can be used to approximate observables of solutions to diffusion equations with log normal distributed diffusion coefficients, e.g. modelling ground water flow. Typical models use log normal diffusion coefficients with H¨older regularity of order up to 1/2 a.s. This low regularity implies that the high frequency finite element approximation error (i.e. the error from frequencies larger than the mesh frequency) is not negligible and can be larger than the computable low frequency error. This talk will address how the total error can be estimated by the computable error.

Experimental determination of the local heat transfer coefficient in a closely packed pin arrangement

International Nuclear Information System (INIS)

Moeller, S.V.

1982-09-01

The determination of the heat transfer coefficient of the pins of the Spallation Neutron Source is a very important problem for the development of this facility, as data for thermal and structural studies. For this purpose, a test apparatus was built, in scale 1:1, for the simulation of the thermal and hydraulical conditions of the Neutron Source. This apparatus is a pin bank, with one of the pins electrically heated. Performance of measurements gave the values for the heat transfer coefficient, here presented in the Nusselt Number form, and its local distribution. Results show the linear dependence of Nusselt Number on Reynolds Number, for a constant heat production. (orig.) [de

Colocalization coefficients evaluating the distribution of molecular targets in microscopy methods based on pointed patterns

Czech Academy of Sciences Publication Activity Database

Pastorek, Lukáš; Sobol, Margaryta; Hozák, Pavel

2016-01-01

Roč. 146, č. 4 (2016), s. 391-406 ISSN 0948-6143 R&D Projects: GA TA ČR(CZ) TE01020118; GA ČR GA15-08738S; GA MŠk(CZ) ED1.1.00/02.0109; GA MŠk(CZ) LM2015062 Grant - others:Human Frontier Science Program(FR) RGP0017/2013 Institutional support: RVO:68378050 Keywords : Colocalization * Quantitative analysis * Pointed patterns * Transmission electron microscopy * Manders' coefficients * Immunohistochemistry Subject RIV: EB - Genetics ; Molecular Biology Impact factor: 2.553, year: 2016

Analysis of the Effects of Streamwise Lift Distribution on Sonic Boom Signature

Science.gov (United States)

Yoo, Paul

2013-01-01

Investigation of sonic boom has been one of the major areas of study in aeronautics due to the benefits a low-boom aircraft has in both civilian and military applications. This work conducts a numerical analysis of the effects of streamwise lift distribution on the shock coalescence characteristics. A simple wing-canard-stabilator body model is used in the numerical simulation. The streamwise lift distribution is varied by fixing the canard at a deflection angle while trimming the aircraft with the wing and the stabilator at the desired lift coefficient. The lift and the pitching moment coefficients are computed using the Missile DATCOM v. 707. The flow field around the wing-canard- stabilator body model is resolved using the OVERFLOW-2 flow solver. Overset/ chimera grid topology is used to simplify the grid generation of various configurations representing different streamwise lift distributions. The numerical simulations are performed without viscosity unless it is required for numerical stability. All configurations are simulated at Mach 1.4, angle-of-attack of 1.50, lift coefficient of 0.05, and pitching moment coefficient of approximately 0. Four streamwise lift distribution configurations were tested.

Reproducibility of The Random Incidence Absorption Coefficient Converted From the Sabine Absorption Coefficient

DEFF Research Database (Denmark)

Jeong, Cheol-Ho; Chang, Ji-ho

2015-01-01

largely depending on the test room. Several conversion methods for porous absorbers from the Sabine absorption coefficient to the random incidence absorption coefficient were suggested by considering the finite size of a test specimen and non-uniformly incident energy onto the specimen, which turned out...... resistivity optimization outperforms the surface impedance optimization in terms of the reproducibility....

Banded Structures in Electron Pitch Angle Diffusion Coefficients from Resonant Wave-Particle Interactions

Science.gov (United States)

Tripathi, A. K.; Singhal, R. P.; Khazanov, G. V.; Avanov, L. A.

2016-01-01

Electron pitch angle (D(sub (alpha alpha))) and momentum (D(sub pp)) diffusion coefficients have been calculated due to resonant interactions with electrostatic electron cyclotron harmonic (ECH) and whistler mode chorus waves. Calculations have been performed at two spatial locations L=4.6 and 6.8 for electron energies less than or equal to 10 keV. Landau (n=0) resonance and cyclotron harmonic resonances n= +/- 1, +/-2, ... +/-5 have been included in the calculations. It is found that diffusion coefficient versus pitch angle (alpha) profiles show large dips and oscillations or banded structures. The structures are more pronounced for ECH and lower band chorus (LBC) and particularly at location 4.6. Calculations of diffusion coefficients have also been performed for individual resonances. It is noticed that the main contribution of ECH waves in pitch angle diffusion coefficient is due to resonances n=+1 and n=+2. A major contribution to momentum diffusion coefficients appears from n=+2. However, the banded structures in D(sub alpha alpha) and D(sub pp) coefficients appear only in the profile of diffusion coefficients for n=+2. The contribution of other resonances to diffusion coefficients is found to be, in general, quite small or even negligible. For LBC and upper band chorus waves, the banded structures appear only in Landau resonance. The D(sub pp) diffusion coefficient for ECH waves is one to two orders smaller than D(sub alpha alpha) coefficients. For chorus waves, D(sub pp) coefficients are about an order of magnitude smaller than D(sub alpha alpha) coefficients for the case n does not equal 0. In case of Landau resonance, the values of D(sub pp) coefficient are generally larger than the values of D(sub alpha alpha) coefficients particularly at lower energies. As an aid to the interpretation of results, we have also determined the resonant frequencies. For ECH waves, resonant frequencies have been estimated for wave normal angle 89 deg and harmonic resonances

The Applicability of the Distribution Coefficient, KD, Based on Non-Aggregated Particulate Samples from Lakes with Low Suspended Solids Concentrations.

Directory of Open Access Journals (Sweden)

Aine Marie Gormley-Gallagher

Full Text Available Separate phases of metal partitioning behaviour in freshwater lakes that receive varying degrees of atmospheric contamination and have low concentrations of suspended solids were investigated to determine the applicability of the distribution coefficient, KD. Concentrations of Pb, Ni, Co, Cu, Cd, Cr, Hg and Mn were determined using a combination of filtration methods, bulk sample collection and digestion and Inductively Coupled Plasma-Mass Spectrometry (ICP-MS. Phytoplankton biomass, suspended solids concentrations and the organic content of the sediment were also analysed. By distinguishing between the phytoplankton and (inorganic lake sediment, transient variations in KD were observed. Suspended solids concentrations over the 6-month sampling campaign showed no correlation with the KD (n = 15 for each metal, p > 0.05 for Mn (r2 = 0.0063, Cu (r2 = 0.0002, Cr (r2 = 0.021, Ni (r2 = 0.0023, Cd (r2 = 0.00001, Co (r2 = 0.096, Hg (r2 = 0.116 or Pb (r2 = 0.164. The results implied that colloidal matter had less opportunity to increase the dissolved (filter passing fraction, which inhibited the spurious lowering of KD. The findings conform to the increasingly documented theory that the use of KD in modelling may mask true information on metal partitioning behaviour. The root mean square error of prediction between the directly measured total metal concentrations and those modelled based on the separate phase fractions were ± 3.40, 0.06, 0.02, 0.03, 0.44, 484.31, 80.97 and 0.1 μg/L for Pb, Cd, Mn, Cu, Hg, Ni, Cr and Co respectively. The magnitude of error suggests that the separate phase models for Mn and Cu can be used in distribution or partitioning models for these metals in lake water.

Determination and reliability of dose coefficients for radiopharmaceuticals; Ermittlung der Zuverlaessigkeit von Dosiskoeffizienten fuer Radiopharmaka

Energy Technology Data Exchange (ETDEWEB)

Spielmann, V.; Li, W.B.; Zankl, M.; Oeh, U.

2015-11-15

The dose coefficients used in nuclear medicine for dose calculations of radiopharmaceuticals are based on recommendations by ICRP (International Commission on radiological protection) and the MIRD (Medical Internal Radiation Dose Committee) using mathematical models for the temporal activity distributions in organs and tissues (biokinetic models) and mathematical models of the human body. These models using an idealized human body do not include uncertainty estimations. The research project is aimed to determine the uncertainties and thus the reliability of the dose coefficients for radiopharmaceuticals and to identify the biokinetic and dosimetric parameters that contribute most of the uncertainties.

Linear Ordinary Differential Equations with Constant Coefficients. Revisiting the Impulsive Response Method Using Factorization

Science.gov (United States)

Camporesi, Roberto

2011-01-01

We present an approach to the impulsive response method for solving linear constant-coefficient ordinary differential equations based on the factorization of the differential operator. The approach is elementary, we only assume a basic knowledge of calculus and linear algebra. In particular, we avoid the use of distribution theory, as well as of…

Drag Coefficient Estimation in Orbit Determination

Science.gov (United States)

McLaughlin, Craig A.; Manee, Steve; Lichtenberg, Travis

2011-07-01

Drag modeling is the greatest uncertainty in the dynamics of low Earth satellite orbits where ballistic coefficient and density errors dominate drag errors. This paper examines fitted drag coefficients found as part of a precision orbit determination process for Stella, Starlette, and the GEOSAT Follow-On satellites from 2000 to 2005. The drag coefficients for the spherical Stella and Starlette satellites are assumed to be highly correlated with density model error. The results using MSIS-86, NRLMSISE-00, and NRLMSISE-00 with dynamic calibration of the atmosphere (DCA) density corrections are compared. The DCA corrections were formulated for altitudes of 200-600 km and are found to be inappropriate when applied at 800 km. The yearly mean fitted drag coefficients are calculated for each satellite for each year studied. The yearly mean drag coefficients are higher for Starlette than Stella, where Starlette is at a higher altitude. The yearly mean fitted drag coefficients for all three satellites decrease as solar activity decreases after solar maximum.

Determination of heat transfer coefficient with vapor condensation inside the tubes diesel’s radiator sections

Directory of Open Access Journals (Sweden)

Y.K.Sklifus

2012-12-01

Full Text Available The article presents the calculation of heat transfer coefficient during condensation of steam, the mathematical model of temperature distribution in the gas and liquid phases of the coolant and the model of the formation of the condensate film on the walls of the tubes.

Airflow in Gravity Sewers - Determination of Wastewater Drag Coefficient.

Science.gov (United States)

Bentzen, Thomas Ruby; Østertoft, Kristian Kilsgaard; Vollertsen, Jes; Fuglsang, Emil Dietz; Nielsen, Asbjørn Haaning

2016-03-01

Several experiments have been conducted in order to improve the understanding of the wastewater drag and the wall frictional force acting on the headspace air in gravity sewers. The aim of the study is to improve the data basis for a numerical model of natural sewer ventilation. The results of the study shows that by integrating the top/side wall shear stresses the log-law models for the air velocity distribution along the unwetted perimeter resulted in a good agreement with the friction forces calculated by use of the Colebrook-White formula for hydraulic smooth pipes. Secondly, the water surface drags were found by log-law models of the velocity distribution in turbulent flows to fit velocity profiles measured from the water surface and by integrating the water surface drags along the wetted perimeter, mean water surface drags were found and a measure of the water surface drag coefficient was found.

Effect of the coefficient of friction and tightening speed on the preload induced at the dental implant complex with the finite element method.

Science.gov (United States)

Bulaqi, Haddad Arabi; Mousavi Mashhadi, Mahmoud; Geramipanah, Farideh; Safari, Hamed; Paknejad, Mojgan

2015-05-01

To prevent screw loosening, a clear understanding of the factors influencing secure preload is necessary. The purpose of this study was to investigate the effect of coefficient of friction and tightening speed on screw tightening based on energy distribution method with exact geometric modeling and finite element analysis. To simulate the proper boundary conditions of the screw tightening process, the supporting bone of an implant was considered. The exact geometry of the implant complex, including the Straumann dental implant, direct crown attachment, and abutment screw were modeled with Solidworks software. Abutment screw/implant and implant/bone interfaces were designed as spiral thread helixes. The screw-tightening process was simulated with Abaqus software, and to achieve the target torque, an angular displacement was applied to the abutment screw head at different coefficients of friction and tightening speeds. The values of torque, preload, energy distribution, elastic energy, and efficiency were obtained at the target torque of 35 Ncm. Additionally, the torque distribution ratio and preload simulated values were compared to theoretically predicted values. Upon reducing the coefficient of friction and enhancing the tightening speed, the angle of turn increased at the target torque. As the angle of turn increased, the elastic energy and preload also increased. Additionally, by increasing the coefficient of friction, the frictional dissipation energy increased but the efficiency decreased, whereas the increase in tightening speed insignificantly affected efficiency. The results of this study indicate that the coefficient of friction is the most influential factor on efficiency. Increasing the tightening speed lowered the response rate to the frictional resistance, thus diminishing the coefficient of friction and slightly increasing the preload. Increasing the tightening speed has the same result as reducing the coefficient of friction. Copyright © 2015

Non-local thermodynamic equilibrium effects on isentropic coefficient in argon and helium thermal plasmas

International Nuclear Information System (INIS)

Sharma, Rohit; Singh, Kuldip

2014-01-01

In the present work, two cases of thermal plasma have been considered; the ground state plasma in which all the atoms and ions are assumed to be in the ground state and the excited state plasma in which atoms and ions are distributed over various possible excited states. The variation of Zγ, frozen isentropic coefficient and the isentropic coefficient with degree of ionization and non-equilibrium parameter θ(= T e /T h ) has been investigated for the ground and excited state helium and argon plasmas at pressures 1 atm, 10 atm, and 100 atm in the temperature range from 6000 K to 60 000 K. For a given value of non-equilibrium parameter, the relationship of Zγ with degree of ionization does not show any dependence on electronically excited states in helium plasma whereas in case of argon plasma this dependence is not appreciable till degree of ionization approaches 2. The minima of frozen isentropic coefficient shifts toward lower temperature with increase of non-equilibrium parameter for both the helium and argon plasmas. The lowering of non-equilibrium parameter decreases the frozen isentropic coefficient more emphatically in helium plasma at high pressures in comparison to argon plasma. The increase of pressure slightly reduces the ionization range over which isentropic coefficient almost remains constant and it does not affect appreciably the dependence of isentropic coefficient on non-equilibrium parameter

Dynamics analysis of SIR epidemic model with correlation coefficients and clustering coefficient in networks.

Science.gov (United States)

Zhang, Juping; Yang, Chan; Jin, Zhen; Li, Jia

2018-07-14

In this paper, the correlation coefficients between nodes in states are used as dynamic variables, and we construct SIR epidemic dynamic models with correlation coefficients by using the pair approximation method in static networks and dynamic networks, respectively. Considering the clustering coefficient of the network, we analytically investigate the existence and the local asymptotic stability of each equilibrium of these models and derive threshold values for the prevalence of diseases. Additionally, we obtain two equivalent epidemic thresholds in dynamic networks, which are compared with the results of the mean field equations. Copyright © 2018 Elsevier Ltd. All rights reserved.

A study on the stem friction coefficient with differential pressure conditions for the motor operated flexible wedge gate valve

International Nuclear Information System (INIS)

Kim, Dae Woong; Park, Sung Keun; Kim, Yang Seok; Lee, Do Hwan

2008-01-01

Stem friction coefficient is very important parameter for the evaluation of valve performance. In this study, the characteristics of stem friction coefficient is analyzed, and the bounding value is determined. The hydraulic testing is performed for flexible wedge gate valves in the plant and statistical method is applied to the determination of bounding value. According to the results of this study, stem friction coefficient is not effected in low differential pressure condition, but it is showed different distribution in medium and high differential pressure condition. And the bounding value of closing stroke is higher than that of opening stroke

Standards for Standardized Logistic Regression Coefficients

Science.gov (United States)

Menard, Scott

2011-01-01

Standardized coefficients in logistic regression analysis have the same utility as standardized coefficients in linear regression analysis. Although there has been no consensus on the best way to construct standardized logistic regression coefficients, there is now sufficient evidence to suggest a single best approach to the construction of a…

Effects of the blockage ratio of a valve disk on loss coefficient in a butterfly valve

International Nuclear Information System (INIS)

Rho, Hyung Joon; Lee, Jee Keun; Choi, Hee Joo

2008-01-01

The loss coefficient of the butterfly valve which allows partial opening of the valve at closed position and is applicable to the small-sized pipe system with the diameter of 1 inch was measured for the variation of the valve disk blockage ratio. Two different types of the valve disk configuration to adjust the blockage ratio were considered. One was the solid type valve disk of which the diameter was changed into the smaller size rather than the pipe diameter, and the other was the perforate type valve disk on which some holes were perforated. The results from two types of valve disk were compared to identify their characteristics in the loss coefficient distributions. The loss coefficient and the controllable angle of the valve disk were decreased exponentially with the decrease of the blockage ratio. In addition, the perforate valve disk had the effect on the higher loss coefficient rather than the solid type valve disk

A Simple Method Using a Topography Correction Coefficient for Estimating Daily Distribution of Solar Irradiance in Complex Terrain

International Nuclear Information System (INIS)

Yun, J.I.

2009-01-01

Accurate solar radiation data are critical to evaluate major physiological responses of plants. For most upland crops and orchard plants growing in complex terrain, however, it is not easy for farmers or agronomists to access solar irradiance data. Here we suggest a simple method using a sun-slope geometry based topographical coefficient to estimate daily solar irradiance on any sloping surfaces from global solar radiation measured at a nearby weather station. An hourly solar irradiance ratio (W i ) between sloping and horizontal surface is defined as multiplication of the relative solar intensity (k i ) and the slope irradiance ratio (r i ) at an hourly interval. The k i is the ratio of hourly solar radiation to the 24 hour cumulative radiation on a horizontal surface under clear sky conditions. The r i is the ratio of clear sky radiation on a given slope to that on a horizontal reference. Daily coefficient for slope correction is simply the sum of W i on each date. We calculated daily solar irradiance at 8 side slope locations circumventing a cone-shaped parasitic volcano (c.a., 570 m diameter for the bottom circle and 90 m bottom-to-top height) by multiplying these coefficients to the global solar radiation measured horizontally. Comparison with the measured slope irradiance from April 2007 to March 2008 resulted in the root mean square error (RMSE) of 1.61 MJ m −2 for the whole period but the RMSE for April to October (i.e., major cropping season in Korea) was much lower and satisfied the 5% error tolerance for radiation measurement. The RMSE was smallest in October regardless of slope aspect, and the aspect dependent variation of RMSE was greatest in November. Annual variation in RMSE was greatest on north and south facing slopes, followed by southwest, southeast, and northwest slopes in decreasing order. Once the coefficients are prepared, global solar radiation data from nearby stations can be easily converted to the solar irradiance map at landscape

Variation in aerodynamic coefficients with altitude

Science.gov (United States)

Shahid, Faiza; Hussain, Mukkarum; Baig, Mirza Mehmood; Haq, Ihtram ul

Precise aerodynamics performance prediction plays key role for a flying vehicle to get its mission completed within desired accuracy. Aerodynamic coefficients for same Mach number can be different at different altitude due to difference in Reynolds number. Prediction of these aerodynamics coefficients can be made through experiments, analytical solution or Computational Fluid Dynamics (CFD). Advancements in computational power have generated the concept of using CFD as a virtual Wind Tunnel (WT), hence aerodynamic performance prediction in present study is based upon CFD (numerical test rig). Simulations at different altitudes for a range of Mach numbers with zero angle of attack are performed to predict axial force coefficient behavior with altitude (Reynolds number). Similar simulations for a fixed Mach number '3' and a range of angle of attacks are also carried out to envisage the variation in normal force and pitching moment coefficients with altitude (Reynolds number). Results clearly depict that the axial force coefficient is a function of altitude (Reynolds number) and increase as altitude increases, especially for subsonic region. Variation in axial force coefficient with altitude (Reynolds number) slightly increases for larger values of angle of attacks. Normal force and pitching moment coefficients do not depend on altitude (Reynolds number) at smaller values of angle of attacks but show slight decrease as altitude increases. Present study suggests that variation of normal force and pitching moment coefficients with altitude can be neglected but the variation of axial force coefficient with altitude should be considered for vehicle fly in dense atmosphere. It is recommended to continue this study to more complex configurations for various Mach numbers with side slip and real gas effects.

Langevin description of fission fragment charge distribution from excited nuclei

CERN Document Server

Karpov, A V

2002-01-01

A stochastic approach to fission dynamics based on a set of three-dimensional Langevin equations was applied to calculate fission-fragment charge distribution of compound nucleus sup 2 sup 3 sup 6 U. The following collective coordinates have been chosen - elongation coordinate, neck-thickness coordinate, and charge-asymmetry coordinate. The friction coefficient of charge mode has been calculated in the framework of one-body and two-body dissipation mechanisms. Analysis of the results has shown that Langevin approach is appropriate for investigation of isobaric distribution. Moreover, the dependences of the variance of the charge distribution on excitation energy and on the two-body viscosity coefficient has been studied

Implications of NGA for NEHRP site coefficients

Science.gov (United States)

Borcherdt, Roger D.

2012-01-01

Three proposals are provided to update tables 11.4-1 and 11.4-2 of Minimum Design Loads for Buildings and Other Structures (7-10), by the American Society of Civil Engineers (2010) (ASCE/SEI 7-10), with site coefficients implied directly by NGA (Next Generation Attenuation) ground motion prediction equations (GMPEs). Proposals include a recommendation to use straight-line interpolation to infer site coefficients at intermediate values of ̅vs (average shear velocity). Site coefficients are recommended to ensure consistency with ASCE/SEI 7-10 MCER (Maximum Considered Earthquake) seismic-design maps and simplified site-specific design spectra procedures requiring site classes with associated tabulated site coefficients and a reference site class with unity site coefficients. Recommended site coefficients are confirmed by independent observations of average site amplification coefficients inferred with respect to an average ground condition consistent with that used for the MCER maps. The NGA coefficients recommended for consideration are implied directly by the NGA GMPEs and do not require introduction of additional models.

A Characterization of Rectangular Distributions

OpenAIRE

Terrell, George R.

1983-01-01

It is well known that the smaller and the larger of a random sample of size two are positively correlated. The coefficient of correlation is at most one-half, and the upper bound is attained only for rectangular distributions.

Adaptive Algebraic Multigrid for Finite Element Elliptic Equations with Random Coefficients

Energy Technology Data Exchange (ETDEWEB)

Kalchev, D

2012-04-02

This thesis presents a two-grid algorithm based on Smoothed Aggregation Spectral Element Agglomeration Algebraic Multigrid (SA-{rho}AMGe) combined with adaptation. The aim is to build an efficient solver for the linear systems arising from discretization of second-order elliptic partial differential equations (PDEs) with stochastic coefficients. Examples include PDEs that model subsurface flow with random permeability field. During a Markov Chain Monte Carlo (MCMC) simulation process, that draws PDE coefficient samples from a certain distribution, the PDE coefficients change, hence the resulting linear systems to be solved change. At every such step the system (discretized PDE) needs to be solved and the computed solution used to evaluate some functional(s) of interest that then determine if the coefficient sample is acceptable or not. The MCMC process is hence computationally intensive and requires the solvers used to be efficient and fast. This fact that at every step of MCMC the resulting linear system changes, makes an already existing solver built for the old problem perhaps not as efficient for the problem corresponding to the new sampled coefficient. This motivates the main goal of our study, namely, to adapt an already existing solver to handle the problem (with changed coefficient) with the objective to achieve this goal to be faster and more efficient than building a completely new solver from scratch. Our approach utilizes the local element matrices (for the problem with changed coefficients) to build local problems associated with constructed by the method agglomerated elements (a set of subdomains that cover the given computational domain). We solve a generalized eigenproblem for each set in a subspace spanned by the previous local coarse space (used for the old solver) and a vector, component of the error, that the old solver cannot handle. A portion of the spectrum of these local eigen-problems (corresponding to eigenvalues close to zero) form the

Probabilistic optimization of safety coefficients

International Nuclear Information System (INIS)

Marques, M.; Devictor, N.; Magistris, F. de

1999-01-01

This article describes a reliability-based method for the optimization of safety coefficients defined and used in design codes. The purpose of the optimization is to determine the partial safety coefficients which minimize an objective function for sets of components and loading situations covered by a design rule. This objective function is a sum of distances between the reliability of the components designed using the safety coefficients and a target reliability. The advantage of this method is shown on the examples of the reactor vessel, a vapour pipe and the safety injection circuit. (authors)

Determination of the heat transfer coefficient from IRT measurement data using the Trefftz method

Directory of Open Access Journals (Sweden)

Maciejewska Beata

2016-01-01

Full Text Available The paper presents the method of heat transfer coefficient determination for boiling research during FC-72 flow in the minichannels, each 1.7 mm deep, 24 mm wide and 360 mm long. The heating element was the thin foil, enhanced on the side which comes into contact with fluid in the minichannels. Local values of the heat transfer coefficient were calculated from the Robin boundary condition. The foil temperature distribution and the derivative of the foil temperature were obtained by solving the two-dimensional inverse heat conduction problem, due to measurements obtained by IRT. Calculations was carried out by the method based on the approximation of the solution of the problem using a linear combination of Trefftz functions. The basic property of this functions is they satisfy the governing equation. Unknown coefficients of linear combination of Trefftz functions are calculated from the minimization of the functional that expresses the mean square error of the approximate solution on the boundary. The results presented as IR thermographs, two-phase flow structure images and the heat transfer coefficient as a function of the distance from the channel inlet, were analyzed.

Estimation of the simple correlation coefficient.

Science.gov (United States)

Shieh, Gwowen

2010-11-01

This article investigates some unfamiliar properties of the Pearson product-moment correlation coefficient for the estimation of simple correlation coefficient. Although Pearson's r is biased, except for limited situations, and the minimum variance unbiased estimator has been proposed in the literature, researchers routinely employ the sample correlation coefficient in their practical applications, because of its simplicity and popularity. In order to support such practice, this study examines the mean squared errors of r and several prominent formulas. The results reveal specific situations in which the sample correlation coefficient performs better than the unbiased and nearly unbiased estimators, facilitating recommendation of r as an effect size index for the strength of linear association between two variables. In addition, related issues of estimating the squared simple correlation coefficient are also considered.

Variation in aerodynamic coefficients with altitude

Directory of Open Access Journals (Sweden)

Faiza Shahid

Full Text Available Precise aerodynamics performance prediction plays key role for a flying vehicle to get its mission completed within desired accuracy. Aerodynamic coefficients for same Mach number can be different at different altitude due to difference in Reynolds number. Prediction of these aerodynamics coefficients can be made through experiments, analytical solution or Computational Fluid Dynamics (CFD. Advancements in computational power have generated the concept of using CFD as a virtual Wind Tunnel (WT, hence aerodynamic performance prediction in present study is based upon CFD (numerical test rig. Simulations at different altitudes for a range of Mach numbers with zero angle of attack are performed to predict axial force coefficient behavior with altitude (Reynolds number. Similar simulations for a fixed Mach number ‘3’ and a range of angle of attacks are also carried out to envisage the variation in normal force and pitching moment coefficients with altitude (Reynolds number. Results clearly depict that the axial force coefficient is a function of altitude (Reynolds number and increase as altitude increases, especially for subsonic region. Variation in axial force coefficient with altitude (Reynolds number slightly increases for larger values of angle of attacks. Normal force and pitching moment coefficients do not depend on altitude (Reynolds number at smaller values of angle of attacks but show slight decrease as altitude increases. Present study suggests that variation of normal force and pitching moment coefficients with altitude can be neglected but the variation of axial force coefficient with altitude should be considered for vehicle fly in dense atmosphere. It is recommended to continue this study to more complex configurations for various Mach numbers with side slip and real gas effects. Keywords: Mach number, Reynolds number, Blunt body, Altitude effect, Angle of attacks

Anomalous Seebeck coefficient in boron carbides

International Nuclear Information System (INIS)

Aselage, T.L.; Emin, D.; Wood, C.; Mackinnon, I.D.R.; Howard, I.A.

1987-01-01

Boron carbides exhibit an anomalously large Seebeck coefficient with a temperature coefficient that is characteristic of polaronic hopping between inequivalent sites. The inequivalence in the sites is associated with disorder in the solid. The temperature dependence of the Seebeck coefficient for materials prepared by different techniques provides insight into the nature of the disorder

Fe+3 diffusion coefficient in Fricke xylenol gel through shielding half of a 6 MV photon beam field size

International Nuclear Information System (INIS)

Cavalcante, Fernanda; Oliveira, Lucas de; Almeida, Adelaide de

2009-01-01

Diffusion of ions can be observed in a solution or gel when a difference occurs in their concentrations. For dosimetric gels, the diffusion can interfere on measurements of absorbed dose delivered to the patient in a radiotherapic treatment, when the time interval for measurements pos-irradiation is considered long. In the present work, a pos-irradiation Fricke Xylenol Gel (FXG) spatial dose distribution was obtained for several time intervals and the diffusion coefficient was inferred following a literature theoretical methodology. Using FXG samples, whose [Fe 2+ ] are oxidated to [Fe +3 ] when irradiated, the diffusion coefficient for the last ion was obtained in order that one can have the real spatial dose distribution right after the irradiation and this was done using half shielded 6 MV photons field size. Each sample, for each time interval selected (from 2.8 up to 28.6 hours) was analyzed in function of their optical absorbance. From Fick's law and from an error equation, the diffusion coefficient was inferred, which can be used to correct the absorbance positions promptly after irradiation. The diffusion coefficient found for the FXG dosimeter, has the value of 0.452 mm 2 /h, that is between the interval of 0.3 up to 2.0 mm 2 /h, predicted for gel type dosimeters. (author)

An Investigation of the Restitution Coefficient Impact on Simulating Sand-Char Mixing in a Bubbling Fluidized Bed

Directory of Open Access Journals (Sweden)

Xinjun Zhao

2017-05-01

Full Text Available In the present work, the effect of the restitution coefficient on the numerical results for a binary mixture system of sand particles and char particles in a bubbling fluidized bed with a huge difference between the particles in terms of density and volume fraction has been studied based on two-fluid model along with the kinetic theory of granular flow. Results show that the effect of restitution coefficient on the flow characteristics varies in different regions of the bed, which is more evident for the top region of the bed. The restitution coefficient can be categorized into two classes. The restitution coefficients of 0.7 and 0.8 can be included into one class, whereas the restitution coefficient of 0.9 and 0.95 can be included into another class. Moreover, four vortices can be found in the time-averaged flow pattern distribution, which is very different from the result obtained for the binary system with the similar values between particles in density and volume fraction.

Apparent diffusion coefficient measurements in progressive supranuclear palsy

Energy Technology Data Exchange (ETDEWEB)

Ohshita, T.; Oka, M.; Imon, Y.; Yamaguchi, S.; Mimori, Y.; Nakamura, S. [Hiroshima Univ. (Japan). School of Medicine

2000-09-01

We measured the apparent diffusion coefficient (ADC), using diffusion-weighted imaging (DWI) and signal intensity on T2-weighted MRI in the cerebral white matter of patients with progressive supranuclear palsy (PSP) and age-matched normal subjects. In PSP, ADC in the prefrontal and precentral white matter was significantly higher than in controls. There was no significant difference in signal intensity on T2-weighted images. The ADC did correlate with signal intensity. The distribution of the elevation of ADC may be the consequence of underlying pathological changes, such as neurofibrillary tangles or glial fibrillary tangles in the cortex. Our findings suggest that ADC measurement might be useful for demonstrating subtle neuropathological changes. (orig.)

Weighted congestion coefficient feedback in intelligent transportation systems

International Nuclear Information System (INIS)

Dong Chuanfei; Ma Xu; Wang Binghong

2010-01-01

In traffic systems, a reasonable information feedback can improve road capacity. In this Letter, we study dynamics of traffic flow with real-time information. And the influence of a feedback strategy named Weighted Congestion Coefficient Feedback Strategy (WCCFS) is introduced, based on a two-route scenario in which dynamic information can be generated and displayed on the board to guide road users to make a choice. Our model incorporates the effects of adaptability into the cellular automaton models of traffic flow and simulation results adopting this optimal information feedback strategy have demonstrated high efficiency in controlling spatial distribution of traffic patterns compared with the other three information feedback strategies, i.e., vehicle number and flux.

Determination of the surface drag coefficient

DEFF Research Database (Denmark)

Mahrt, L.; Vickers, D.; Sun, J.L.

2001-01-01

This study examines the dependence of the surface drag coefficient on stability, wind speed, mesoscale modulation of the turbulent flux and method of calculation of the drag coefficient. Data sets over grassland, sparse grass, heather and two forest sites are analyzed. For significantly unstable...... conditions, the drag coefficient does not depend systematically on z/L but decreases with wind speed for fixed intervals of z/L, where L is the Obukhov length. Even though the drag coefficient for weak wind conditions is sensitive to the exact method of calculation and choice of averaging time, the decrease...... of the drag coefficient with wind speed occurs for all of the calculation methods. A classification of flux calculation methods is constructed, which unifies the most common previous approaches. The roughness length corresponding to the usual Monin-Obukhov stability functions decreases with increasing wind...

Development of the loss coefficient correlation for cross flow between graphite fuel blocks in the core of prismatic very high temperature reactor-PMR200

International Nuclear Information System (INIS)

Lee, Jeong-Hun; Cho, Hyoung-Kyu; Park, Goon-Cherl

2016-01-01

Highlights: • Cross flow experimental data are produced with wedge-shaped and parallel gaps. • The results of a CFD analysis and experimental data are in good agreement. • Pressure loss coefficient for the cross gap between fuel blocks in PMR200 is found. • A new correlation of the cross flow loss coefficient for PMR200 is proposed. - Abstract: The core of the very high temperature reactor (VHTR) PMR200 (a prismatic modular reactor rated at 200 MW of thermal power) consists of hexagonal prismatic fuel blocks and reflector blocks made of graphite. If the core bypass flow ratio increases, the coolant channel flow is decreased and can then lower the heat removal efficiency, resulting in a locally increased fuel block temperature. The coolant channels in the fuel blocks are connected to bypass gaps by the cross gap, complicating flow distribution in the VHTR core. Therefore, reliable estimation of the bypass flow is highly important for the design and safety analysis of the VHTR core. Because of the complexity of the core geometry and gap configuration, it is challenging to predict the flow distribution in the VHTR core. To analyze this flow distribution accurately, it is necessary to determine the cross flow phenomena, and the loss coefficient across the cross gap has to be evaluated to determine the flow distribution in the VHTR core when a lumped parameter code or a flow network analysis code that uses the correlation of the loss coefficient is employed. The purpose of this paper is to develop a loss coefficient correlation applicable to the cross gap in the PMR200 core. The cross flow was evaluated experimentally using the difference between the measured inlet and outlet mass flow rates. Next, the applicability of a commercial computational fluid dynamics (CFD) code, CFX 15, was confirmed by comparing the experimental data and CFD analysis results. To understand the cross flow phenomena, the loss coefficient was evaluated; in the high Reynolds number region

Development of the loss coefficient correlation for cross flow between graphite fuel blocks in the core of prismatic very high temperature reactor-PMR200

Energy Technology Data Exchange (ETDEWEB)

Lee, Jeong-Hun, E-mail: huny12@snu.ac.kr; Cho, Hyoung-Kyu, E-mail: chohk@snu.ac.kr; Park, Goon-Cherl, E-mail: parkgc@snu.ac.kr

2016-10-15

Highlights: • Cross flow experimental data are produced with wedge-shaped and parallel gaps. • The results of a CFD analysis and experimental data are in good agreement. • Pressure loss coefficient for the cross gap between fuel blocks in PMR200 is found. • A new correlation of the cross flow loss coefficient for PMR200 is proposed. - Abstract: The core of the very high temperature reactor (VHTR) PMR200 (a prismatic modular reactor rated at 200 MW of thermal power) consists of hexagonal prismatic fuel blocks and reflector blocks made of graphite. If the core bypass flow ratio increases, the coolant channel flow is decreased and can then lower the heat removal efficiency, resulting in a locally increased fuel block temperature. The coolant channels in the fuel blocks are connected to bypass gaps by the cross gap, complicating flow distribution in the VHTR core. Therefore, reliable estimation of the bypass flow is highly important for the design and safety analysis of the VHTR core. Because of the complexity of the core geometry and gap configuration, it is challenging to predict the flow distribution in the VHTR core. To analyze this flow distribution accurately, it is necessary to determine the cross flow phenomena, and the loss coefficient across the cross gap has to be evaluated to determine the flow distribution in the VHTR core when a lumped parameter code or a flow network analysis code that uses the correlation of the loss coefficient is employed. The purpose of this paper is to develop a loss coefficient correlation applicable to the cross gap in the PMR200 core. The cross flow was evaluated experimentally using the difference between the measured inlet and outlet mass flow rates. Next, the applicability of a commercial computational fluid dynamics (CFD) code, CFX 15, was confirmed by comparing the experimental data and CFD analysis results. To understand the cross flow phenomena, the loss coefficient was evaluated; in the high Reynolds number region

Study of transport coefficients of nanodiamond nanofluids

Science.gov (United States)

Pryazhnikov, M. I.; Minakov, A. V.; Guzei, D. V.

2017-09-01

Experimental data on the thermal conductivity coefficient and viscosity coefficient of nanodiamond nanofluids are presented. Distilled water and ethylene glycol were used as the base fluid. Dependences of transport coefficients on concentration are obtained. It was shown that the thermal conductivity coefficient increases with increasing nanodiamonds concentration. It was shown that base fluids properties and nanodiamonds concentration affect on the rheology of nanofluids.

Application of matriciant method for calculation of the third order aberration coefficients for magnetic field with regard to boundary effects

International Nuclear Information System (INIS)

Mordik, S.N.; Ponomarev, A.G.

2001-01-01

To study nonlinear dynamics of charged particles in magnetic sector analyzers one applied the matriciant method. When calculating matriciants (transfer matrices) one took account of the boundary-value effects associated with the effect of scattering field, as well as, the higher harmonics of the sector magnetic field up to the third order inclusive. In case of the rectangular distribution of field components along the optical axis one obtained analytical expressions for all aberration coefficients up to the third order exclusive. To simulate the real field with the width of scattering field not equal to zero one applied smooth distribution of components for which calculation of similar aberration coefficients was conducted using the conservative numerical method [ru

Sediment distribution coefficients (KD) and concentration factors (CF) in fish for natural radionuclides in a pond of a tropical region and their contributions to estimations of internal absorbed dose rate in fish

International Nuclear Information System (INIS)

Souza Pereira, Wagner de; Kelecom, Alphonse

2008-01-01

Attention has been paid only recently to the protection of biota against radiation effects. Protection is being considered through modeling of the calculation of absorbed dose rate. In these models, the inputs are the fluxes of radionuclides of environmental concern and their resulting distribution between environmental compartments. Such distribution is estimated for dispersion models. In freshwater systems and when fish is used as biomaker, relevant environmental transfer parameters are transfer between sediment and water (sediment distribution coefficients KD, in l kg -1 ), and between water and fish (concentration factor CF, in l kg -1 ). These coefficients are under the influence of a number o physical, chemical and biological factors, and display following the literature a great variability. The present work establishes the KD's and CF's for uranium, thorium, radium and lead for two ponds: one that receives treated effluents from an ore treatment unit (UTM) situated at Pocos de Caldas, Minas Gerais, Brazil and the other pond from the uranium concentration unit (URA) situated at Caetite, Bahia, Brazil, and for fish used as biomarker. It intends also to compare these parameters with the values recommended by IAEA. Depending on considered radionuclide and on the site, CF's (l kg -1 ) observed values were of the same magnitude as, or one order of magnitude lower than recommended by IAEA. KD's (l kg -1 ) observed values were found of the same magnitude as those recommended by IAEA, approximately 10 times lower or up to 100 times higher than recommended by IAEA, again depending on the radionuclides and on the site. It can be concluded that local parameters should be established in order to obtain a more accurate estimative of biota exposition from man activities. (author)

General approach to the computation of local transport coefficients with finite Larmor effects in the collision contribution

International Nuclear Information System (INIS)

Ghendrih, P.

1986-10-01

We expand the distribution functions on a basis of Hermite functions and obtain a general scheme to compute the local transport coefficients. The magnetic field dependence due to finite Larmor radius effects during the collision process is taken into account

Quasihomogeneous distributions

CERN Document Server

von Grudzinski, O

1991-01-01

This is a systematic exposition of the basics of the theory of quasihomogeneous (in particular, homogeneous) functions and distributions (generalized functions). A major theme is the method of taking quasihomogeneous averages. It serves as the central tool for the study of the solvability of quasihomogeneous multiplication equations and of quasihomogeneous partial differential equations with constant coefficients. Necessary and sufficient conditions for solvability are given. Several examples are treated in detail, among them the heat and the Schrödinger equation. The final chapter is devoted to quasihomogeneous wave front sets and their application to the description of singularities of quasihomogeneous distributions, in particular to quasihomogeneous fundamental solutions of the heat and of the Schrödinger equation.

Computable error estimates for Monte Carlo finite element approximation of elliptic PDE with lognormal diffusion coefficients

KAUST Repository

Hall, Eric

2016-01-09

The Monte Carlo (and Multi-level Monte Carlo) finite element method can be used to approximate observables of solutions to diffusion equations with lognormal distributed diffusion coefficients, e.g. modeling ground water flow. Typical models use lognormal diffusion coefficients with H´ older regularity of order up to 1/2 a.s. This low regularity implies that the high frequency finite element approximation error (i.e. the error from frequencies larger than the mesh frequency) is not negligible and can be larger than the computable low frequency error. We address how the total error can be estimated by the computable error.

Diffraction Theory and Almost Periodic Distributions

Science.gov (United States)

Strungaru, Nicolae; Terauds, Venta

2016-09-01

We introduce and study the notions of translation bounded tempered distributions, and autocorrelation for a tempered distribution. We further introduce the spaces of weakly, strongly and null weakly almost periodic tempered distributions and show that for weakly almost periodic tempered distributions the Eberlein decomposition holds. For translation bounded measures all these notions coincide with the classical ones. We show that tempered distributions with measure Fourier transform are weakly almost periodic and that for this class, the Eberlein decomposition is exactly the Fourier dual of the Lebesgue decomposition, with the Fourier-Bohr coefficients specifying the pure point part of the Fourier transform. We complete the project by looking at few interesting examples.

Computing eigenvalue sensitivity coefficients to nuclear data based on the CLUTCH method with RMC code

International Nuclear Information System (INIS)

Qiu, Yishu; She, Ding; Tang, Xiao; Wang, Kan; Liang, Jingang

2016-01-01

Highlights: • A new algorithm is proposed to reduce memory consumption for sensitivity analysis. • The fission matrix method is used to generate adjoint fission source distributions. • Sensitivity analysis is performed on a detailed 3D full-core benchmark with RMC. - Abstract: Recently, there is a need to develop advanced methods of computing eigenvalue sensitivity coefficients to nuclear data in the continuous-energy Monte Carlo codes. One of these methods is the iterated fission probability (IFP) method, which is adopted by most of Monte Carlo codes of having the capabilities of computing sensitivity coefficients, including the Reactor Monte Carlo code RMC. Though it is accurate theoretically, the IFP method faces the challenge of huge memory consumption. Therefore, it may sometimes produce poor sensitivity coefficients since the number of particles in each active cycle is not sufficient enough due to the limitation of computer memory capacity. In this work, two algorithms of the Contribution-Linked eigenvalue sensitivity/Uncertainty estimation via Tracklength importance CHaracterization (CLUTCH) method, namely, the collision-event-based algorithm (C-CLUTCH) which is also implemented in SCALE and the fission-event-based algorithm (F-CLUTCH) which is put forward in this work, are investigated and implemented in RMC to reduce memory requirements for computing eigenvalue sensitivity coefficients. While the C-CLUTCH algorithm requires to store concerning reaction rates of every collision, the F-CLUTCH algorithm only stores concerning reaction rates of every fission point. In addition, the fission matrix method is put forward to generate the adjoint fission source distribution for the CLUTCH method to compute sensitivity coefficients. These newly proposed approaches implemented in RMC code are verified by a SF96 lattice model and the MIT BEAVRS benchmark problem. The numerical results indicate the accuracy of the F-CLUTCH algorithm is the same as the C

Thermal Coefficient of Linear Expansion Modified by Dendritic Segregation in Nickel-Iron Alloys

Science.gov (United States)

Ogorodnikova, O. M.; Maksimova, E. V.

2018-05-01

The paper presents investigations of thermal properties of Fe-Ni and Fe-Ni-Co casting alloys affected by the heterogeneous distribution of their chemical elements. It is shown that nickel dendritic segregation has a negative effect on properties of studied invars. A mathematical model is proposed to explore the influence of nickel dendritic segregation on the thermal coefficient of linear expansion (TCLE) of the alloy. A computer simulation of TCLE of Fe-Ni-Co superinvars is performed with regard to a heterogeneous distribution of their chemical elements over the whole volume. The ProLigSol computer software application is developed for processing the data array and results of computer simulation.

Lorenz curve and Gini coefficient reveal hot spots and hot moments for nitrous oxide emissions

Science.gov (United States)

Identifying hot spots and hot moments of N2O emissions in the landscape is critical for monitoring and mitigating the emission of this powerful greenhouse gas. We propose a novel use of the Lorenz curve and Gini coefficient (G) to quantify the heterogeneous distribution of N2O emissions from a lands...

Revised spatially distributed global livestock emissions

Science.gov (United States)

Asrar, G.; Wolf, J.; West, T. O.

2015-12-01

Livestock play an important role in agricultural carbon cycling through consumption of biomass and emissions of methane. Quantification and spatial distribution of methane and carbon dioxide produced by livestock is needed to develop bottom-up estimates for carbon monitoring. These estimates serve as stand-alone international emissions estimates, as input to global emissions modeling, and as comparisons or constraints to flux estimates from atmospheric inversion models. Recent results for the US suggest that the 2006 IPCC default coefficients may underestimate livestock methane emissions. In this project, revised coefficients were calculated for cattle and swine in all global regions, based on reported changes in body mass, quality and quantity of feed, milk production, and management of living animals and manure for these regions. New estimates of livestock methane and carbon dioxide emissions were calculated using the revised coefficients and global livestock population data. Spatial distribution of population data and associated fluxes was conducted using the MODIS Land Cover Type 5, version 5.1 (i.e. MCD12Q1 data product), and a previously published downscaling algorithm for reconciling inventory and satellite-based land cover data at 0.05 degree resolution. Preliminary results for 2013 indicate greater emissions than those calculated using the IPCC 2006 coefficients. Global total enteric fermentation methane increased by 6%, while manure management methane increased by 38%, with variation among species and regions resulting in improved spatial distributions of livestock emissions. These new estimates of total livestock methane are comparable to other recently reported studies for the entire US and the State of California. These new regional/global estimates will improve the ability to reconcile top-down and bottom-up estimates of methane production as well as provide updated global estimates for use in development and evaluation of Earth system models.

Estimation of the thermal diffusion coefficient in fusion plasmas taking frequency measurement uncertainties into account

International Nuclear Information System (INIS)

Van Berkel, M; Hogeweij, G M D; Van den Brand, H; De Baar, M R; Zwart, H J; Vandersteen, G

2014-01-01

In this paper, the estimation of the thermal diffusivity from perturbative experiments in fusion plasmas is discussed. The measurements used to estimate the thermal diffusivity suffer from stochastic noise. Accurate estimation of the thermal diffusivity should take this into account. It will be shown that formulas found in the literature often result in a thermal diffusivity that has a bias (a difference between the estimated value and the actual value that remains even if more measurements are added) or have an unnecessarily large uncertainty. This will be shown by modeling a plasma using only diffusion as heat transport mechanism and measurement noise based on ASDEX Upgrade measurements. The Fourier coefficients of a temperature perturbation will exhibit noise from the circular complex normal distribution (CCND). Based on Fourier coefficients distributed according to a CCND, it is shown that the resulting probability density function of the thermal diffusivity is an inverse non-central chi-squared distribution. The thermal diffusivity that is found by sampling this distribution will always be biased, and averaging of multiple estimated diffusivities will not necessarily improve the estimation. Confidence bounds are constructed to illustrate the uncertainty in the diffusivity using several formulas that are equivalent in the noiseless case. Finally, a different method of averaging, that reduces the uncertainty significantly, is suggested. The methodology is also extended to the case where damping is included, and it is explained how to include the cylindrical geometry. (paper)

A simple model for skewed species-lifetime distributions

KAUST Repository

Murase, Yohsuke

2010-06-11

A simple model of a biological community assembly is studied. Communities are assembled by successive migrations and extinctions of species. In the model, species are interacting with each other. The intensity of the interaction between each pair of species is denoted by an interaction coefficient. At each time step, a new species is introduced to the system with randomly assigned interaction coefficients. If the sum of the coefficients, which we call the fitness of a species, is negative, the species goes extinct. The species-lifetime distribution is found to be well characterized by a stretched exponential function with an exponent close to 1/2. This profile agrees not only with more realistic population dynamics models but also with fossil records. We also find that an age-independent and inversely diversity-dependent mortality, which is confirmed in the simulation, is a key mechanism accounting for the distribution. © IOP Publishing Ltd and Deutsche Physikalische Gesellschaft.

Analysis of internal conversion coefficients

International Nuclear Information System (INIS)

Coursol, N.; Gorozhankin, V.M.; Yakushev, E.A.; Briancon, C.; Vylov, Ts.

2000-01-01

An extensive database has been assembled that contains the three most widely used sets of calculated internal conversion coefficients (ICC): [Hager R.S., Seltzer E.C., 1968. Internal conversion tables. K-, L-, M-shell Conversion coefficients for Z=30 to Z=103, Nucl. Data Tables A4, 1-237; Band I.M., Trzhaskovskaya M.B., 1978. Tables of gamma-ray internal conversion coefficients for the K-, L- and M-shells, 10≤Z≤104, Special Report of Leningrad Nuclear Physics Institute; Roesel F., Fries H.M., Alder K., Pauli H.C., 1978. Internal conversion coefficients for all atomic shells, At. Data Nucl. Data Tables 21, 91-289] and also includes new Dirac-Fock calculations [Band I.M. and Trzhaskovskaya M.B., 1993. Internal conversion coefficients for low-energy nuclear transitions, At. Data Nucl. Data Tables 55, 43-61]. This database is linked to a computer program to plot ICCs and their combinations (sums and ratios) as a function of Z and energy, as well as relative deviations of ICC or their combinations for any pair of tabulated data. Examples of these analyses are presented for the K-shell and total ICCs of the gamma-ray standards [Hansen H.H., 1985. Evaluation of K-shell and total internal conversion coefficients for some selected nuclear transitions, Eur. Appl. Res. Rept. Nucl. Sci. Tech. 11.6 (4) 777-816] and for the K-shell and total ICCs of high multipolarity transitions (total, K-, L-, M-shells of E3 and M3 and K-shell of M4). Experimental data sets are also compared with the theoretical values of these specific calculations

The distribution of chlamydia, gonorrhoea and syphilis cases across states and counties in the USA, 2007.

Science.gov (United States)

Chesson, Harrell W; Sternberg, Maya; Leichliter, Jami S; Aral, Sevgi O

2010-12-01

To examine the distribution of chlamydia, gonorrhoea and syphilis in the USA through the use of Lorenz curves and Gini coefficients. The distribution of three sexually transmitted diseases (STD; chlamydia, gonorrhoea and primary and secondary syphilis) was examined across states and counties in the USA in 2007, based on reported case numbers. Gini coefficients, which can range from 0 (equality in STD rates across geographical units) to 1 (complete inequality such that all STD occur in one geographical unit) were calculated. Overall, chlamydia was the most evenly distributed and syphilis was the most concentrated of the three STD examined. The Gini coefficients for chlamydia, gonorrhoea and syphilis were 0.121, 0.255 and 0.334, respectively, when examined across states, and 0.319, 0.494 and 0.630, respectively, when examined across counties. Differences in Gini coefficients were observed when the STD distributions were examined by sex, race/ethnicity and age group. The use of Lorenz curves and Gini coefficients can help to assess inequalities in the distribution of STD, to gauge the suitability of geographically targeted interventions, and to help in determining the epidemic phase of STD. Having a better understanding of the disparities in the distribution of STD across states and counties by sex, race/ethnicity and age group might help in understanding why disparities in STD rates exist across different groups and in developing interventions to address these disparities.

Revised Mark 22 coolant temperature coefficients

International Nuclear Information System (INIS)

Graves, W.E.

1987-01-01

Coolant temperature coefficients for the Mark 22 charge published previously are non-conservative because of the neglect of a significant mechanism which has a positive contribution to reactivity. Even after correcting for this effect, dynamic tests made on a Mark VIB charge in the early 60's suggest the results are still non-conservative. This memorandum takes both of these sources of information into account in making a best estimate of the prompt (coolant plus metal) temperature coefficient. Although no safety issues arise from this work (the overall temperature coefficient still strongly contributes to reactor stability), it is obviously desirable to use best estimates for prompt coefficients in limits and other calculations

Transport Coefficients from Large Deviation Functions

Directory of Open Access Journals (Sweden)

Chloe Ya Gao

2017-10-01

Full Text Available We describe a method for computing transport coefficients from the direct evaluation of large deviation functions. This method is general, relying on only equilibrium fluctuations, and is statistically efficient, employing trajectory based importance sampling. Equilibrium fluctuations of molecular currents are characterized by their large deviation functions, which are scaled cumulant generating functions analogous to the free energies. A diffusion Monte Carlo algorithm is used to evaluate the large deviation functions, from which arbitrary transport coefficients are derivable. We find significant statistical improvement over traditional Green–Kubo based calculations. The systematic and statistical errors of this method are analyzed in the context of specific transport coefficient calculations, including the shear viscosity, interfacial friction coefficient, and thermal conductivity.

Transport Coefficients from Large Deviation Functions

Science.gov (United States)

Gao, Chloe; Limmer, David

2017-10-01

We describe a method for computing transport coefficients from the direct evaluation of large deviation function. This method is general, relying on only equilibrium fluctuations, and is statistically efficient, employing trajectory based importance sampling. Equilibrium fluctuations of molecular currents are characterized by their large deviation functions, which is a scaled cumulant generating function analogous to the free energy. A diffusion Monte Carlo algorithm is used to evaluate the large deviation functions, from which arbitrary transport coefficients are derivable. We find significant statistical improvement over traditional Green-Kubo based calculations. The systematic and statistical errors of this method are analyzed in the context of specific transport coefficient calculations, including the shear viscosity, interfacial friction coefficient, and thermal conductivity.

Power coefficient anomaly in JOYO

Energy Technology Data Exchange (ETDEWEB)

Yamamoto, H

1980-12-15

Operation of the JOYO experimental fast reactor with the MK-I core has been divided into two phases: (1) 50 MWt power ascension and operation; and (2) 75 MWt power ascension and operation. The 50 MWt power-up tests were conducted in August 1978. In these tests, the measured reactivity loss due to power increases from 15 MWt to 50 MWt was 0.28% ..delta.. K/K, and agreed well with the predicted value of 0.27% ..delta.. K/K. The 75 MWt power ascension tests were conducted in July-August 1979. In the process of the first power increase above 50 MWt to 65 MWt conducted on July 11, 1979, an anomalously large negative power coefficient was observed. The value was about twice the power coefficient values measured in the tests below 50 MW. In order to reproduce the anomaly, the reactor power was decreased and again increased up to the maximum power of 65 MWt. However, the large negative power coefficient was not observed at this time. In the succeeding power increase from 65 MWt to 75 MWt, a similar anomalous power coefficient was again observed. This anomaly disappeared in the subsequent power ascensions to 75 MWt, and the magnitude of the power coefficient gradually decreased with power cycles above the 50 MWt level.

Random errors in the magnetic field coefficients of superconducting quadrupole magnets

International Nuclear Information System (INIS)

Herrera, J.; Hogue, R.; Prodell, A.; Thompson, P.; Wanderer, P.; Willen, E.

1987-01-01

The random multipole errors of superconducting quadrupoles are studied. For analyzing the multipoles which arise due to random variations in the size and locations of the current blocks, a model is outlined which gives the fractional field coefficients from the current distributions. With this approach, based on the symmetries of the quadrupole magnet, estimates are obtained of the random multipole errors for the arc quadrupoles envisioned for the Relativistic Heavy Ion Collider and for a single-layer quadrupole proposed for the Superconducting Super Collider

Correlation between octanol/water and liposome/water distribution coefficients and drug absorption of a set of pharmacologically active compounds.

Science.gov (United States)

Esteves, Freddy; Moutinho, Carla; Matos, Carla

2013-06-01

Absorption and consequent therapeutic action are key issues in the development of new drugs by the pharmaceutical industry. In this sense, different models can be used to simulate biological membranes to predict the absorption of a drug. This work compared the octanol/water and the liposome/water models. The parameters used to relate the two models were the distribution coefficients between liposomes and water and octanol and water and the fraction of drug orally absorbed. For this study, 66 drugs were collected from literature sources and divided into four groups according to charge and ionization degree: neutral; positively charged; negatively charged; and partially ionized/zwitterionic. The results show a satisfactory linear correlation between the octanol and liposome systems for the neutral (R²= 0.9324) and partially ionized compounds (R²= 0.9367), contrary to the positive (R²= 0.4684) and negatively charged compounds (R²= 0.1487). In the case of neutral drugs, results were similar in both models because of the high fraction orally absorbed. However, for the charged drugs (positively, negatively, and partially ionized/zwitterionic), the liposomal model has a more-appropriate correlation with absorption than the octanol model. These results show that the neutral compounds only interact with membranes through hydrophobic bonds, whereas charged drugs favor electrostatic interactions established with the liposomes. With this work, we concluded that liposomes may be a more-appropriate biomembrane model than octanol for charged compounds.

Sensitivity Analysis of the Surface Runoff Coefficient of HiPIMS in Simulating Flood Processes in a Large Basin

Directory of Open Access Journals (Sweden)

Yueling Wang

2018-03-01

Full Text Available To simulate flood processes at the basin level, the GPU-based High-Performance Integrated Hydrodynamic Modelling System (HiPIMS is gaining interest as computational capability increases. However, the difficulty of coping with rainfall input to HiPIMS reduces the possibility of acquiring a satisfactory simulation accuracy. The objective of this study is to test the sensitivity of the surface runoff coefficient in the HiPIMS source term in the Misai basin with an area of 797 km2 in south China. To achieve this, the basin was divided into 909,824 grid cells, to each of which a Manning coefficient was assigned based on its land use type interpreted from remote sensing data. A sensitivity analysis was conducted for three typical flood processes under four types of surface runoff coefficients, assumed a priori, upon three error functions. The results demonstrate the crucial role of the surface runoff coefficient in achieving better simulation accuracy and reveal that this coefficient varies with flood scale and is unevenly distributed over the basin.

Multiplicity distribution and forward-backward correlations in the hydrodynamic theory of multiple production

International Nuclear Information System (INIS)

Tarasov, Yu.A.

1992-01-01

A hydrodynamic model for the collisions of gluon clusters is used to calculate the charge-particle multiplicity distributions in collisions of nucleons at ISR and collider energies. The separation temperature of the hydrodynamic system is calculated as a function of the rapidity [T k (γ 1 )] for each value of the inelasticity coefficient K. In the central region, this temperature is higher at collider energies than at the ISR energy. The average number of resonance clusters which decay into various (fixed) numbers of charged hadrons is found for each value of K. The number of these clusters fluctuates in accordance with a Poisson distribution. A hadron multiplicity distribution which incorporates these fluctuations is found. This distribution is averaged over the inelasticity coefficient. The distributions p(n ch ) and the KNO functions Ψ(z) are calculated for the overall and central regions of the rapidity, |y| ≤ 1.5. The broadening of the distributions and the violation of KNO scaling at collider energies results from increased contributions from the decays of resonances. The front-back multiplicity correlations are also studied; the decay of resonances is taken into account. The distributions and slope coefficients of the correlation function which are found for the various energies agree with experimental data

The Impact of Variable Wind Shear Coefficients on Risk Reduction of Wind Energy Projects.

Science.gov (United States)

Corscadden, Kenneth W; Thomson, Allan; Yoonesi, Behrang; McNutt, Josiah

2016-01-01

Estimation of wind speed at proposed hub heights is typically achieved using a wind shear exponent or wind shear coefficient (WSC), variation in wind speed as a function of height. The WSC is subject to temporal variation at low and high frequencies, ranging from diurnal and seasonal variations to disturbance caused by weather patterns; however, in many cases, it is assumed that the WSC remains constant. This assumption creates significant error in resource assessment, increasing uncertainty in projects and potentially significantly impacting the ability to control gird connected wind generators. This paper contributes to the body of knowledge relating to the evaluation and assessment of wind speed, with particular emphasis on the development of techniques to improve the accuracy of estimated wind speed above measurement height. It presents an evaluation of the use of a variable wind shear coefficient methodology based on a distribution of wind shear coefficients which have been implemented in real time. The results indicate that a VWSC provides a more accurate estimate of wind at hub height, ranging from 41% to 4% reduction in root mean squared error (RMSE) between predicted and actual wind speeds when using a variable wind shear coefficient at heights ranging from 33% to 100% above the highest actual wind measurement.

Cross-section and rate coefficient calculation for electron impact excitation, ionisation and dissociation of H2 and OH molecules

International Nuclear Information System (INIS)

Riahi, R.; Ben Lakhdar, Z.; Teulet, Ph.; Gleizes, A.

2006-01-01

The weighted total cross-sections (WTCS) theory is used to calculate electron impact excitation, ionization and dissociation cross-sections and rate coefficients of OH, H 2 , OH + , H 2 + , OH - and H 2 - diatomic molecules in the temperature range 1500-15000 K. Calculations are performed for H 2 (X, B, C), OH(X, A, B), H 2 + (X), OH + (X, a, A, b, c), H 2 - (X) and OH - (X) electronic states for which Dunham coefficients are available. Rate coefficients are calculated from WTCS assuming Maxwellian energy distribution functions for electrons and heavy particles. One and 2 temperatures (θ e and θ g respectively for electron and heavy particles kinetic temperatures) results are presented and fitting parameters (a, b and c) are given for each reaction rate coefficient: k(θ) a(θ b )exp(-c/θ). (authors)

New results on the 3-loop heavy flavor Wilson coefficients in deep-inelastic scattering

Energy Technology Data Exchange (ETDEWEB)

Ablinger, Jakob; Schneider, Carsten [Johannes Kepler Univ., Linz (Austria). Research Inst. for Symbolic Computation; Bluemlein, Johannes; Freitas, Abilio de; Wissbrock, Fabian [Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Hasselhuhn, Alexander [Johannes Kepler Univ., Linz (Austria). Research Inst. for Symbolic Computation; Deutsches Elektronen-Synchrotron (DESY), Zeuthen (Germany); Klein, Sebastian [RWTH Aachen Univ. (Germany). Inst. fuer Theoretische Physik E

2013-01-02

We report on recent results obtained for the 3-loop heavy flavor Wilson coefficients in deepinelastic scattering (DIS) at general values of the Mellin variable N at larger scales of Q{sup 2}. These concern contributions to the gluonic ladder-topologies, the transition matrix elements in the variable flavor scheme of O(n{sub f}T{sup 2}{sub F}) and O(T{sup 2}{sub F}), and first results on higher 3-loop topologies. The knowledge of the heavy flavor Wilson coefficients at 3-loop order is of importance to extract the parton distribution functions and {alpha}{sub s}(M{sup 2}{sub Z}) in complete NNLO QCD analyses of the world precision data on the structure function F{sub 2}(x,Q{sup 2}).

Friction coefficient dependence on electrostatic tribocharging.

Science.gov (United States)

Burgo, Thiago A L; Silva, Cristiane A; Balestrin, Lia B S; Galembeck, Fernando

2013-01-01

Friction between dielectric surfaces produces patterns of fixed, stable electric charges that in turn contribute electrostatic components to surface interactions between the contacting solids. The literature presents a wealth of information on the electronic contributions to friction in metals and semiconductors but the effect of triboelectricity on friction coefficients of dielectrics is as yet poorly defined and understood. In this work, friction coefficients were measured on tribocharged polytetrafluoroethylene (PTFE), using three different techniques. As a result, friction coefficients at the macro- and nanoscales increase many-fold when PTFE surfaces are tribocharged, but this effect is eliminated by silanization of glass spheres rolling on PTFE. In conclusion, tribocharging may supersede all other contributions to macro- and nanoscale friction coefficients in PTFE and probably in other insulating polymers.

Ion distributions, exclusion coefficients, and separation factors of electrolytes in a charged cylindrical nanopore: a partially perturbative density functional theory study.

Science.gov (United States)

Peng, Bo; Yu, Yang-Xin

2009-10-07

The structural and thermodynamic properties for charge symmetric and asymmetric electrolytes as well as mixed electrolyte system inside a charged cylindrical nanopore are investigated using a partially perturbative density functional theory. The electrolytes are treated in the restricted primitive model and the internal surface of the cylindrical nanopore is considered to have a uniform charge density. The proposed theory is directly applicable to the arbitrary mixed electrolyte solution containing ions with the equal diameter and different valences. Large amount of simulation data for ion density distributions, separation factors, and exclusion coefficients are used to determine the range of validity of the partially perturbative density functional theory for monovalent and multivalent counterion systems. The proposed theory is found to be in good agreement with the simulations for both mono- and multivalent counterion systems. In contrast, the classical Poisson-Boltzmann equation only provides reasonable descriptions of monovalent counterion system at low bulk density, and is qualitatively and quantitatively wrong in the prediction for the multivalent counterion systems due to its neglect of the strong interionic correlations in these systems. The proposed density functional theory has also been applied to an electrolyte absorbed into a pore that is a model of the filter of a physiological calcium channel.

Matching the quasiparton distribution in a momentum subtraction scheme

Science.gov (United States)

Stewart, Iain W.; Zhao, Yong

2018-03-01

The quasiparton distribution is a spatial correlation of quarks or gluons along the z direction in a moving nucleon which enables direct lattice calculations of parton distribution functions. It can be defined with a nonperturbative renormalization in a regularization independent momentum subtraction scheme (RI/MOM), which can then be perturbatively related to the collinear parton distribution in the MS ¯ scheme. Here we carry out a direct matching from the RI/MOM scheme for the quasi-PDF to the MS ¯ PDF, determining the non-singlet quark matching coefficient at next-to-leading order in perturbation theory. We find that the RI/MOM matching coefficient is insensitive to the ultraviolet region of convolution integral, exhibits improved perturbative convergence when converting between the quasi-PDF and PDF, and is consistent with a quasi-PDF that vanishes in the unphysical region as the proton momentum Pz→∞ , unlike other schemes. This direct approach therefore has the potential to improve the accuracy for converting quasidistribution lattice calculations to collinear distributions.

Hermite-Gaussian beams with self-forming spiral phase distribution

Science.gov (United States)

Zinchik, Alexander A.; Muzychenko, Yana B.

2014-05-01

Spiral laser beams is a family of laser beams that preserve the structural stability up to scale and rotate with the propagation. Properties of spiral beams are of practical interest for laser technology, medicine and biotechnology. Researchers use a spiral beams for movement and manipulation of microparticles. Spiral beams have a complicated phase distribution in cross section. This paper describes the results of analytical and computer simulation of Hermite-Gaussian beams with self-forming spiral phase distribution. In the simulation used a laser beam consisting of the sum of the two modes HG TEMnm and TEMn1m1. The coefficients n1, n, m1, m were varied. Additional phase depending from the coefficients n, m, m1, n1 imposed on the resulting beam. As a result, formed the Hermite Gaussian beam phase distribution which takes the form of a spiral in the process of distribution. For modeling was used VirtualLab 5.0 (manufacturer LightTrans GmbH).

Estimation of expected value for lognormal and gamma distributions

International Nuclear Information System (INIS)

White, G.C.

1978-01-01

Concentrations of environmental pollutants tend to follow positively skewed frequency distributions. Two such density functions are the gamma and lognormal. Minimum variance unbiased estimators of the expected value for both densities are available. The small sample statistical properties of each of these estimators were compared for its own distribution, as well as the other distribution to check the robustness of the estimator. Results indicated that the arithmetic mean provides an unbiased estimator when the underlying density function of the sample is either lognormal or gamma, and that the achieved coverage of the confidence interval is greater than 75 percent for coefficients of variation less than two. Further Monte Carlo simulations were conducted to study the robustness of the above estimators by simulating a lognormal or gamma distribution with the expected value of a particular observation selected from a uniform distribution before the lognormal or gamma observation is generated. Again, the arithmetic mean provides an unbiased estimate of expected value, and the coverage of the confidence interval is greater than 75 percent for coefficients of variation less than two

Pressure distribution over tube surfaces of tube bundle subjected to two phase cross flow

International Nuclear Information System (INIS)

Sim, Woo Gun

2013-01-01

Two phase vapor liquid flows exist in many shell and tube heat exchangers such as condensers, evaporators and nuclear steam generators. To understand the fluid dynamic forces acting on a structure subjected to a two phase flow, it is essential to obtain detailed information about the characteristics of a two phase flow. The characteristics of a two phase flow and the flow parameters were introduced, and then, an experiment was performed to evaluate the pressure loss in the tube bundles and the fluid dynamic force acting on the cylinder owing to the pressure distribution. A two phase flow was pre mixed at the entrance of the test section, and the experiments were undertaken using a normal triangular array of cylinders subjected to a two phase cross flow. The pressure loss along the flow direction in the tube bundles was measured to calculate the two phase friction multiplier, and the multiplier was compared with the analytical value. Furthermore, the circular distributions of the pressure on the cylinders were measured. Based on the distribution and the fundamental theory of two phase flow, the effects of the void fraction and mass flux per unit area on the pressure coefficient and the drag coefficient were evaluated. The drag coefficient was calculated by integrating the measured pressure coefficient and the drag coefficient were evaluated. The drag coefficient was calculated by integrating the measured pressure on the tube by a numerical method. It was found that for low mass fluxes, the measured two phase friction multipliers agree well with the analytical results, and good agreement for the effect of the void fraction on the drag coefficients, as calculated by the measured pressure distributions, is shown qualitatively, as compared to the existing experimental results

Anticonvulsant profile of a balanced ketogenic diet in acute mouse seizure models.

Science.gov (United States)

Samala, Ramakrishna; Willis, Sarah; Borges, Karin

2008-10-01

Anticonvulsant effects of the ketogenic diet (KD) have been reported in the mouse, although previous studies did not control for intake of vitamins, minerals and antioxidants. The aim of this study was to examine the effects of balanced ketogenic and control diets in acute mouse seizure models. The behavior in four mouse seizure models, plasma d-beta-hydroxybutyrate (d-BHB) and glucose levels were determined after feeding control diet, 4:1 and 6:1 KDs with matched vitamins, minerals and antioxidants. Feeding 4:1 and 6:1 KDs ad lib to 3-week-old (adolescent) mice resulted in 1.2-2.2mM d-BHB in plasma, but did not consistently change glucose levels. The 6:1 KD reproducibly elevated the CC50 (current that initiates seizures in 50% mice tested) in the 6-Hz model after 14 days of feeding to adolescent CD1 mice. Higher plasma d-BHB levels correlated with anticonvulsant effects. Despite ketosis, no consistent anticonvulsant effects of KDs were found in the fluorothyl or pentylenetetrazole CD1 mouse models. The 4:1 KD was neither anticonvulsant nor neuroprotective in hippocampus in the C3H mouse kainate model. Taken together, the KD's anticonvulsant effect was limited to the 6-Hz model, required chronic feeding with 6:1 fat content, and was independent from lowering plasma glucose.

Assessment of Aliasing Errors in Low-Degree Coefficients Inferred from GPS Data

Directory of Open Access Journals (Sweden)

Na Wei

2016-05-01

Full Text Available With sparse and uneven site distribution, Global Positioning System (GPS data is just barely able to infer low-degree coefficients in the surface mass field. The unresolved higher-degree coefficients turn out to introduce aliasing errors into the estimates of low-degree coefficients. To reduce the aliasing errors, the optimal truncation degree should be employed. Using surface displacements simulated from loading models, we theoretically prove that the optimal truncation degree should be degree 6–7 for a GPS inversion and degree 20 for combing GPS and Ocean Bottom Pressure (OBP with no additional regularization. The optimal truncation degree should be decreased to degree 4–5 for real GPS data. Additionally, we prove that a Scaled Sensitivity Matrix (SSM approach can be used to quantify the aliasing errors due to any one or any combination of unresolved higher degrees, which is beneficial to identify the major error source from among all the unresolved higher degrees. Results show that the unresolved higher degrees lower than degree 20 are the major error source for global inversion. We also theoretically prove that the SSM approach can be used to mitigate the aliasing errors in a GPS inversion, if the neglected higher degrees are well known from other sources.

Distribution measurement of 60Co target radioactive specific activity

International Nuclear Information System (INIS)

Li Xingyan; Chen Zigen; Ren Min

1994-01-01

Radioactive specific activity distribution of cobalt 60 target by irradiation in HFETR is a key parameter. With the collimate principle, the under water measurement device and conversion coefficient which is get by experiments, and the radioactive specific activity distribution is obtained. The uncertainty of measurement is less than 10%

Dual – Temperature Electron distribution in a Laboratory Plasma ...

African Journals Online (AJOL)

The dual-temperature distribution function is used to investigate theoretically the effect of a perturbation of Maxwell distribution function on density ratios in a laboratory plasma produced solely by collision. By assuming a foreknowledge of collision coefficients and cross-sections and an atomic model which sets at two ...

Friction coefficient dependence on electrostatic tribocharging

Science.gov (United States)

Burgo, Thiago A. L.; Silva, Cristiane A.; Balestrin, Lia B. S.; Galembeck, Fernando

2013-01-01

Friction between dielectric surfaces produces patterns of fixed, stable electric charges that in turn contribute electrostatic components to surface interactions between the contacting solids. The literature presents a wealth of information on the electronic contributions to friction in metals and semiconductors but the effect of triboelectricity on friction coefficients of dielectrics is as yet poorly defined and understood. In this work, friction coefficients were measured on tribocharged polytetrafluoroethylene (PTFE), using three different techniques. As a result, friction coefficients at the macro- and nanoscales increase many-fold when PTFE surfaces are tribocharged, but this effect is eliminated by silanization of glass spheres rolling on PTFE. In conclusion, tribocharging may supersede all other contributions to macro- and nanoscale friction coefficients in PTFE and probably in other insulating polymers. PMID:23934227

Control rod position and temperature coefficients in HTTR power-rise tests. Interim report

International Nuclear Information System (INIS)

Fujimoto, Nozomu; Nojiri, Naoki; Takada, Eiji; Saito, Kenji; Kobayashi, Shoichi; Sawahata, Hiroaki; Kokusen, Sigeru

2001-03-01

Power-rise tests of the High Temperature Engineering Test Reactor (HTTR) have been carried out aiming to achieve 100% power. So far, 50% of power operation and many tests have been carried out. In the HTTR, temperature change in core is so large to achieve the outlet coolant temperature of 950degC. To improve the calculation accuracy of the HTTR reactor physics characteristics, control rod positions at criticality and temperature coefficients were measured at each step to achieve 50% power level. The calculations were carried out using Monte Carlo code and diffusion theory with temperature distributions in the core obtained by reciprocal calculation of thermo-hydraulic code and diffusion theory. Control rod positions and temperature coefficients were calculated by diffusion theory and Monte Carlo method. The test results were compared to calculation results. The control rod positions at criticality showed good agreement with calculation results by Monte Carlo method with error of 50 mm. The control position at criticality at 100% was predicted around 2900mm. Temperature coefficients showed good agreement with calculation results by diffusion theory. The improvement of calculation will be carried out comparing the measured results up to 100% power level. (author)

Studies on the matched potential method for determining the selectivity coefficients of ion-selective electrodes based on neutral ionophores: experimental and theoretical verification.

Science.gov (United States)

Tohda, K; Dragoe, D; Shibata, M; Umezawa, Y

2001-06-01

A theory is presented that describes the matched potential method (MPM) for the determination of the potentiometric selectivity coefficients (KA,Bpot) of ion-selective electrodes for two ions with any charge. This MPM theory is based on electrical diffuse layers on both the membrane and the aqueous side of the interface, and is therefore independent of the Nicolsky-Eisenman equation. Instead, the Poisson equation is used and a Boltzmann distribution is assumed with respect to all charged species, including primary, interfering and background electrolyte ions located at the diffuse double layers. In this model, the MPM-selectivity coefficients of ions with equal charge (ZA = ZB) are expressed as the ratio of the concentrations of the primary and interfering ions in aqueous solutions at which the same amounts of the primary and interfering ions permselectively extracted into the membrane surface. For ions with unequal charge (ZA not equal to ZB), the selectivity coefficients are expressed as a function not only of the amounts of the primary and interfering ions permeated into the membrane surface, but also of the primary ion concentration in the initial reference solution and the delta EMF value. Using the measured complexation stability constants and single ion distribution coefficients for the relevant systems, the corresponding MPM selectivity coefficients can be calculated from the developed MPM theory. It was found that this MPM theory is capable of accurately and precisely predicting the MPM selectivity coefficients for a series of ion-selective electrodes (ISEs) with representative ionophore systems, which are generally in complete agreement with independently determined MPM selectivity values from the potentiometric measurements. These results also conclude that the assumption for the Boltzmann distribution was in fact valid in the theory. The recent critical papers on MPM have pointed out that because the MPM selectivity coefficients are highly concentration

MANCOVA for one way classification with homogeneity of regression coefficient vectors

Science.gov (United States)

Mokesh Rayalu, G.; Ravisankar, J.; Mythili, G. Y.

2017-11-01

The MANOVA and MANCOVA are the extensions of the univariate ANOVA and ANCOVA techniques to multidimensional or vector valued observations. The assumption of a Gaussian distribution has been replaced with the Multivariate Gaussian distribution for the vectors data and residual term variables in the statistical models of these techniques. The objective of MANCOVA is to determine if there are statistically reliable mean differences that can be demonstrated between groups later modifying the newly created variable. When randomization assignment of samples or subjects to groups is not possible, multivariate analysis of covariance (MANCOVA) provides statistical matching of groups by adjusting dependent variables as if all subjects scored the same on the covariates. In this research article, an extension has been made to the MANCOVA technique with more number of covariates and homogeneity of regression coefficient vectors is also tested.

Calculation of transport coefficients in an axisymmetric plasma

International Nuclear Information System (INIS)

Shumaker, D.E.

1976-01-01

A method of calculating the transport coefficient in an axisymmetric toroidal plasma is presented. This method is useful in calculating the transport coefficients in a Tokamak plasma confinement device. The particle density and temperature are shown to be a constant on a magnetic flux surface. Transport equations are given for the total particle flux and total energy flux crossing a closed toroidal surface. Also transport equations are given for the toroidal magnetic flux. A computer code was written to calculate the transport coefficients for a three species plasma, electrons and two species of ions. This is useful for calculating the transport coefficients of a plasma which contains impurities. It was found that the particle and energy transport coefficients are increased by a large amount, and the transport coefficients for the toroidal magnetic field are reduced by a small amount. For example, a deuterium plasma with 1.3 percent oxygen, one of the particle transport coefficients is increased by a factor of about four. The transport coefficients for the toroidal magnetic flux are reduced by about 20 percent. The increase in the particle transport coefficient is due to the collisional scattering of the deuterons by the heavy oxygen ions which is larger than the deuteron electron scattering, the normal process for particle transport in a two species plasma. The reduction in the toroidal magnetic flux transport coefficients are left unexplained

Anomalous temperature dependence of the Seebeck coefficient for the substitutionally-disordered hopping conductors

International Nuclear Information System (INIS)

Raffaelle, R.P.; Parris, P.E.; Anderson, H.U.; Sparlin, D.M.

1991-01-01

Thermoelectric power measurements are presented for the (La,Sr)(Cr,Mn)O 3 series. The nonlinear temperature dependence of the Seebeck coefficient is analyzed in terms of a random distribution of energetically equivalent hopping sites. The limitations of Heikes' formula, which has been traditionally used to calculate small polaron carrier densities in these systems, are discussed. Recent theoretical developments in the interpretation of Seebeck measurements in substitutionally-disordered high-temperature hopping conductors are reviewed

Transfer coefficients in ultracold strongly coupled plasma