WorldWideScience

Sample records for direct digital design

  1. Reconfigurable multivariable control law for commercial airplane using a direct digital output feedback design

    Ostroff, A. J.; Hueschen, R. M.

    1984-01-01

    The ability of a pilot to reconfigure the control surfaces on an airplane after a failure, allowing the airplane to recover to a safe condition for landing, becomes more difficult with increasing airplane complexity. Techniques are needed to stabilize and control the airplane immediately after a failure, allowing the pilot time to make longer range decisions. This paper shows a design of a discrete multivariable control law using four controls for the longitudinal channel of a B-737. Single control element failures are allowed in three of the four controls. The four controls design and failure cases are analyzed by means of a digital airplane simulation, with regard to tracking capability and ability to overcome severe windshear and turbulence during the aproach and landing phase of flight.

  2. Broadband direct RF digitization receivers

    Jamin, Olivier

    2014-01-01

    This book discusses the trade-offs involved in designing direct RF digitization receivers for the radio frequency and digital signal processing domains.  A system-level framework is developed, quantifying the relevant impairments of the signal processing chain, through a comprehensive system-level analysis.  Special focus is given to noise analysis (thermal noise, quantization noise, saturation noise, signal-dependent noise), broadband non-linear distortion analysis, including the impact of the sampling strategy (low-pass, band-pass), analysis of time-interleaved ADC channel mismatches, sampling clock purity and digital channel selection. The system-level framework described is applied to the design of a cable multi-channel RF direct digitization receiver. An optimum RF signal conditioning, and some algorithms (automatic gain control loop, RF front-end amplitude equalization control loop) are used to relax the requirements of a 2.7GHz 11-bit ADC. A two-chip implementation is presented, using BiCMOS and 65nm...

  3. Digital Art and Design

    Batiha, Khaled; Al Salaimeh, Safwan; Besoul, Khaldoun

    2007-01-01

    The desire to create unique things and give free rain to one's imagination served as a powerful impetus to the development of digital art and design software. The commoner was the use of computers the wider variety of professional software was developed. Nowadays the creators and computer designers are receiving more and more new and advanced programs that allow their ideas becoming virtual reality. This research paper looks at the history of the development of graphic editors from the simple...

  4. Digital Art and Design

    Khaldoun A. A. BESOUL

    2006-07-01

    Full Text Available The desire to create unique things and give free rain to one's imagination served as a powerful impetus to the development of digital art and design software. The commoner was the use of computers the wider variety of professional software was developed. Nowadays the creators and computer designers are receiving more and more new and advanced programs that allow their ideas becoming virtual reality. This research paper looks at the history of the development of graphic editors from the simplest to the most modern and advanced. This brief survey includes the history of different graphic editors’ creation, their features and abilities. This paper highlights the two basic branches of graphic editors – these that are in free use and commercial graphic editors design software. The researcher selected the most powerful and influential graphic editors design software brands like Paint.NET and GIMP among free software and commercial Adobe Photoshop. This paper also dwells upon the way digital art transferred from the exclusively professional business into the hobby for ordinary users. This research paper bears implications for those who are interested in features and potentiality of most popular graphic editors design software.

  5. Direct digital conversion detector technology

    Mandl, William J.; Fedors, Richard

    1995-06-01

    Future imaging sensors for the aerospace and commercial video markets will depend on low cost, high speed analog-to-digital (A/D) conversion to efficiently process optical detector signals. Current A/D methods place a heavy burden on system resources, increase noise, and limit the throughput. This paper describes a unique method for incorporating A/D conversion right on the focal plane array. This concept is based on Sigma-Delta sampling, and makes optimum use of the active detector real estate. Combined with modern digital signal processors, such devices will significantly increase data rates off the focal plane. Early conversion to digital format will also decrease the signal susceptibility to noise, lowering the communications bit error rate. Computer modeling of this concept is described, along with results from several simulation runs. A potential application for direct digital conversion is also reviewed. Future uses for this technology could range from scientific instruments to remote sensors, telecommunications gear, medical diagnostic tools, and consumer products.

  6. Digital design and computer architecture

    Harris, David

    2010-01-01

    Digital Design and Computer Architecture is designed for courses that combine digital logic design with computer organization/architecture or that teach these subjects as a two-course sequence. Digital Design and Computer Architecture begins with a modern approach by rigorously covering the fundamentals of digital logic design and then introducing Hardware Description Languages (HDLs). Featuring examples of the two most widely-used HDLs, VHDL and Verilog, the first half of the text prepares the reader for what follows in the second: the design of a MIPS Processor. By the end of D

  7. New directions in pediatric digital imaging

    Fletcher, B.D.; Adams, R.B.; Blackham, W.C.

    1985-01-01

    In this chapter the authors describe several simple experiments performed utilizing digital equipment which apply to clinical situations in pediatrics and which suggest future directions for research in digital imaging. They also discuss experimental systems which they believe will overcome certain limitations of current equipment and might be applicable to pediatric digital imaging in the future

  8. Digital fluxgate magnetometer: design notes

    Belyayev, Serhiy; Ivchenko, Nickolay

    2015-01-01

    We presented an approach to understanding the performance of a fully digital fluxgate magnetometer. All elements of the design are important for the performance of the instrument, and the presence of the digital feed-back loop introduces certain peculiarities affecting the noise and dynamic performance of the instrument. Ultimately, the quantisation noise of the digital to analogue converter is found to dominate the noise of the current design, although noise shaping alleviates its effect to some extent. An example of magnetometer measurements on board a sounding rocket is presented, and ways to further improve the performance of the instrument are discussed. (paper)

  9. Digital fluxgate magnetometer: design notes

    Belyayev, Serhiy; Ivchenko, Nickolay

    2015-12-01

    We presented an approach to understanding the performance of a fully digital fluxgate magnetometer. All elements of the design are important for the performance of the instrument, and the presence of the digital feed-back loop introduces certain peculiarities affecting the noise and dynamic performance of the instrument. Ultimately, the quantisation noise of the digital to analogue converter is found to dominate the noise of the current design, although noise shaping alleviates its effect to some extent. An example of magnetometer measurements on board a sounding rocket is presented, and ways to further improve the performance of the instrument are discussed.

  10. Digital system design with VHDL

    Kang, Jin Gu; Lee, Da Young; Song, Je Chel

    2000-09-01

    This book is comprised of eleven chapters, which are review of basic logic design including combinational logic circuit, KARNAUGH MAPS, Hazard of combinational circuit, Melay order circuit design and synchronous design, introduction of VHDL like VHDL module of Multiplexer and VHDL Function, design with PLD for program, circuit design for arithmetical operation, digital design using SM chart, PGA and CPLD design, Floating-point calculation, extra issues on VHDL, VHDL module for memory and bus,design for hardware test and a testing and examples for design such as UART design and M68HC05 micro controller.

  11. Design in the digital textbook

    Ebbesen, Toke Riis

    reorganization of the publishing company, web based user interfaces, and ultimately the branding, that market these new digital objects, are building powerful discourses around the product. Thus it is suggested that the design process of the iBog-case can be understood in a model of database-based publishing......Building on a preliminary case study of the Danish educational publisher, Systime A/S, and its flagship product, the web based ‘iBog’ {Systime 2014}, this paper explores how digital textbooks can be understood as design. The shaping of digital books is seen as intertwined in a wider circuit...... with multiple levels. In the final analysis, the iBog is much more than a product and a technology. It is a brand that goes beyond what can be studied by looking at the digital textbook as a singular artefact....

  12. ARSITEKTUR DVD (Digital Virtual Design

    Danny Santoso Mintorogo

    2000-01-01

    Full Text Available Soon after the millennium year of 2000 and toward 21th century, the ways of architecture design will be a great change from traditional hand design and drawings to super computer digital virtual design models with tremendous of high-end architectural 3D software domains. Virtual Technology will be a plus to architectural design stage to obtain several "scheme" and observe with real - time feedback of the quality (height, light, furniture, shape, and environment as well as the sequential of the space, site context or massing studies. Abstract in Bahasa Indonesia : Strategi dalam desain arsitektur pada abad 22 atau setelah tahun milinium 2000 ini akan banyak didominasi dengan perangkap teknologi canggih yang tentunya akan mengandalkan pada perangkap keras (komputer dan perangkap lunak (software untuk tujuan desain arsitektur secara digital. Teknologi "Virtual" akan dimanfaatkan untuk bidang arsitektur dalam mengoptimasikan disain arsitektur secara digital maya, untuk mengobservasi/mengkaji kwalitas ruang, model suatu ruang/massa secara maya dalam phase perancangan arsitektur. Kata kunci: arsitektur, desain, digital, maya.

  13. Interface design for digital courses

    Tabbers, Huib; Kester, Liesbeth; Hummel, Hans; Nadolski, Rob

    2005-01-01

    This text should be referred to as: Tabbers, H., Kester, L., Hummel, H. G. K., & Nadolski, R. J. (2003). Interface design for digital courses. In W. Jochems, J. van Merriënboer, & R. Koper (Eds). Integrated e-learning: implications for pedagogy, technology & organisation (pp. 100-111). London:

  14. Digital libraries philosophies, technical design considerations, and example scenarios

    Stern, David

    1999-01-01

    An unparalleled overview of current design considerations for your digital library! Digital Libraries: Philosophies, Technical Design Considerations, and Example Scenarios is a balanced overview of public services, collection development, administration, and systems support, for digital libraries, with advice on adopting the latest technologies that appear on the scene. As a professional in the library and information science field, you will benefit from this special issue that serves as an overview of selected directions, trends, possibilities, limitations, enhancements, design principals, an

  15. Digital Games, Design, and Learning

    Clark, Douglas B.; Tanner-Smith, Emily E.; Killingsworth, Stephen S.

    2016-01-01

    In this meta-analysis, we systematically reviewed research on digital games and learning for K–16 students. We synthesized comparisons of game versus nongame conditions (i.e., media comparisons) and comparisons of augmented games versus standard game designs (i.e., value-added comparisons). We used random-effects meta-regression models with robust variance estimates to summarize overall effects and explore potential moderator effects. Results from media comparisons indicated that digital games significantly enhanced student learning relative to nongame conditions (g¯ = 0.33, 95% confidence interval [0.19, 0.48], k = 57, n = 209). Results from value-added comparisons indicated significant learning benefits associated with augmented game designs (g¯ = 0.34, 95% confidence interval [0.17, 0.51], k = 20, n = 40). Moderator analyses demonstrated that effects varied across various game mechanics characteristics, visual and narrative characteristics, and research quality characteristics. Taken together, the results highlight the affordances of games for learning as well as the key role of design beyond medium. PMID:26937054

  16. Image rejects in general direct digital radiography

    Hofmann, Bjørn; Rosanowsky, Tine Blomberg; Jensen, Camilla; Wah, Kenneth Hong Ching

    2015-01-01

    The number of rejected images is an indicator of image quality and unnecessary imaging at a radiology department. Image reject analysis was frequent in the film era, but comparably few and small studies have been published after converting to digital radiography. One reason may be a belief that rejects have been eliminated with digitalization. To measure the extension of deleted images in direct digital radiography (DR), in order to assess the rates of rejects and unnecessary imaging and to analyze reasons for deletions, in order to improve the radiological services. All exposed images at two direct digital laboratories at a hospital in Norway were reviewed in January 2014. Type of examination, number of exposed images, and number of deleted images were registered. Each deleted image was analyzed separately and the reason for deleting the image was recorded. Out of 5417 exposed images, 596 were deleted, giving a deletion rate of 11%. A total of 51.3% were deleted due to positioning errors and 31.0% due to error in centering. The examinations with the highest percentage of deleted images were the knee, hip, and ankle, 20.6%, 18.5%, and 13.8% respectively. The reject rate is at least as high as the deletion rate and is comparable with previous film-based imaging systems. The reasons for rejection are quite different in digital systems. This falsifies the hypothesis that digitalization would eliminates rejects. A deleted image does not contribute to diagnostics, and therefore is an unnecessary image. Hence, the high rates of deleted images have implications for management, training, education, as well as for quality

  17. Image rejects in general direct digital radiography.

    Hofmann, Bjørn; Rosanowsky, Tine Blomberg; Jensen, Camilla; Wah, Kenneth Hong Ching

    2015-10-01

    The number of rejected images is an indicator of image quality and unnecessary imaging at a radiology department. Image reject analysis was frequent in the film era, but comparably few and small studies have been published after converting to digital radiography. One reason may be a belief that rejects have been eliminated with digitalization. To measure the extension of deleted images in direct digital radiography (DR), in order to assess the rates of rejects and unnecessary imaging and to analyze reasons for deletions, in order to improve the radiological services. All exposed images at two direct digital laboratories at a hospital in Norway were reviewed in January 2014. Type of examination, number of exposed images, and number of deleted images were registered. Each deleted image was analyzed separately and the reason for deleting the image was recorded. Out of 5417 exposed images, 596 were deleted, giving a deletion rate of 11%. A total of 51.3% were deleted due to positioning errors and 31.0% due to error in centering. The examinations with the highest percentage of deleted images were the knee, hip, and ankle, 20.6%, 18.5%, and 13.8% respectively. The reject rate is at least as high as the deletion rate and is comparable with previous film-based imaging systems. The reasons for rejection are quite different in digital systems. This falsifies the hypothesis that digitalization would eliminates rejects. A deleted image does not contribute to diagnostics, and therefore is an unnecessary image. Hence, the high rates of deleted images have implications for management, training, education, as well as for quality.

  18. Digital computer structure and design

    Townsend, R

    2014-01-01

    Digital Computer Structure and Design, Second Edition discusses switching theory, counters, sequential circuits, number representation, and arithmetic functions The book also describes computer memories, the processor, data flow system of the processor, the processor control system, and the input-output system. Switching theory, which is purely a mathematical concept, centers on the properties of interconnected networks of ""gates."" The theory deals with binary functions of 1 and 0 which can change instantaneously from one to the other without intermediate values. The binary number system is

  19. An experiment in multidisciplinary digital design

    Tuncer, B.; De Ruiter, P.; Mulders, S.

    2008-01-01

    The design and realization of complex buildings requires multidisciplinary design collaboration from early on in the design process. The intensive use of digital design environments in this process demands new knowledge and skills from the involved players including integrating and managing digital

  20. Design Thinking for Digital Fabrication in Education

    Smith, Rachel Charlotte; Iversen, Ole Sejer; Hjorth, Mikkel

    2015-01-01

    In this paper, we argue that digital fabrication in education may benefit from design thinking, to foster a more profound understanding of digital fabrication processes among students. Two related studies of digital fabrication in education are presented in the paper. In an observational study we...... found that students (eleven to fifteen) lacked an understanding of the complexity of the digital fabrication process impeding on the potentials of digital fabrication in education. In a second explorative research through design study, we investigated how a focus on design thinking affected the students...

  1. Personalized direct marketing using digital publishing

    Kutty, Cheeniyil L.; Prabhakaran, Jayasree K.

    2006-02-01

    In today's cost-conscious business climate, marketing and customer service decision makers are increasingly concerned with how to increase customer response and retention rates. Companies spend large amounts of money on Customer Relationship Management (CRM) solutions and data acquisition but they don't know how to use the information stored in these systems to improve the effectiveness of their direct marketing campaigns. By leveraging the customer information they already have, companies can create personalized, printed direct mail programs that generate high response rates, greater returns, and stronger customer loyalty, while gaining a significant edge over their competitors. To reach the promised land of one-to-one direct marketing (personalized direct marketing - PDM), companies need an end-to-end solution for creating, managing, printing, and distributing personalized direct mail "on demand." Having access to digital printing is just one piece of the solution. A more complete approach includes leveraging personalization technology into a useful direct marketing tool that provides true one-to-one marketing, allowing variable images and text in a personalized direct mail. This paper discusses integration of CRM with a Print-on-Demand solution so as to create truly personalized printed marketing campaigns for one or many individuals based on the profile information, preferences and purchase history stored in the CRM.

  2. Design reflowable digital book template

    Prasetya, Didik Dwi; Widiyaningtyas, Triyanna; Arifin, M. Zainal; Wahyu Sakti G., I.

    2017-09-01

    Electronic books (e-books or digital books) increasingly in demand and continue to grow in the form of future books. One of the standard format electronic books that potential is EPUB (electronic publication) published by the International Digital Publishing Forum (IDPF). This digital book has major advantages are able to provide interactive and reflowable content, which are not found in another book format, such as PDF. Reflowable content allows the book can be accessed through a variety of reader device, like desktop and mobile with a fit and comfort view. However, because the generating process of an EPUB digital book is not as easy a PDF, so this format is less popular. Therefore, in order to help overcome the existing problems, this paper develops digital reflowable text book templates to support electronic learning, especially in Indonesia. This template can be used by anyone to produce a standard digital book quickly and easily without requiring additional specialized knowledge.

  3. A Digital Power Quality Monitoring Equipment Designed for Digital Substation

    Li, Wei; Wang, Xin; Geng, Jiewen

    2018-01-01

    Taking into account both current status and development trend of digital substation, this paper proposed a design of a new multi-channelled digital power quality monitoring equipment with high compatibility. The overall functional structure, hardware architecture, software architecture, interface architecture and some key techniques such as IEC 61850 modelling of transient event and harmonic measurement method under the condition of non-synchronous sampling are described in this paper.

  4. Design and Testing of Digital Microfluidic Biochips

    Zhao, Yang

    2013-01-01

    This book provides a comprehensive methodology for automated design, test and diagnosis, and use of robust, low-cost, and manufacturable digital microfluidic systems. It focuses on the development of a comprehensive CAD optimization framework for digital microfluidic biochips that unifies different design problems. With the increase in system complexity and integration levels, biochip designers can utilize the design methods described in this book to evaluate different design alternatives, and carry out design-space exploration to obtain the best design point. Describes practical design automation tools that address different design problems (e.g., synthesis, droplet routing, control-pin mapping, testing and diagnosis, and error recovery) in a unified manner; Applies test pattern generation and error-recovery techniques for digital microfluidics-based biochips; Uses real bioassays as evaluation examples, e.g., multiplexed in vitro human physiological fluids diagnostics, PCR, protein crystallization.  

  5. Automatic design of digital synthetic gene circuits.

    Mario A Marchisio

    2011-02-01

    Full Text Available De novo computational design of synthetic gene circuits that achieve well-defined target functions is a hard task. Existing, brute-force approaches run optimization algorithms on the structure and on the kinetic parameter values of the network. However, more direct rational methods for automatic circuit design are lacking. Focusing on digital synthetic gene circuits, we developed a methodology and a corresponding tool for in silico automatic design. For a given truth table that specifies a circuit's input-output relations, our algorithm generates and ranks several possible circuit schemes without the need for any optimization. Logic behavior is reproduced by the action of regulatory factors and chemicals on the promoters and on the ribosome binding sites of biological Boolean gates. Simulations of circuits with up to four inputs show a faithful and unequivocal truth table representation, even under parametric perturbations and stochastic noise. A comparison with already implemented circuits, in addition, reveals the potential for simpler designs with the same function. Therefore, we expect the method to help both in devising new circuits and in simplifying existing solutions.

  6. Principles of modern digital design

    Lala, Parag K

    2007-01-01

    A major objective of this book is to fill the gap between traditional logic design principles and logic design/optimization techniques used in practice. Over the last two decades several techniques for computer-aided design and optimization of logic circuits have been developed. However, underlying theories of these techniques are inadequately covered or not covered at all in undergraduate text books. This book covers not only the ""classical"" material found in current text books but also selected materials that modern logic designers need to be familiar with.

  7. Digital Hardware Design Teaching: An Alternative Approach

    Benkrid, Khaled; Clayton, Thomas

    2012-01-01

    This article presents the design and implementation of a complete review of undergraduate digital hardware design teaching in the School of Engineering at the University of Edinburgh. Four guiding principles have been used in this exercise: learning-outcome driven teaching, deep learning, affordability, and flexibility. This has identified…

  8. Digital logic circuit design with ALTERA MAX+PLUS II

    Lee, Seung Ho; Park, Yong Su; Park, Gun Jong; Lee, Ju Heon

    2006-09-01

    This book is composed of five parts. The first part has introduction of ALTERA MAX+PLUS II and graphic editor, text editor, compiler, waveform editor simulator and timing analyzer of it. The second part is about direction of digital logic circuit design with training kit. The third part has grammar and practice of VHDL in ALTERA MAX+PLUS II including example and history of VHDL. The fourth part shows the design example of digital logic circuit by VHDL of ALTERA MAX+PLUS II which lists designs of adder and subtractor, code converter, counter, state machine and LCD module. The last part explains design example of digital logic circuit by graphic editor in ALTERA MAX+PLUS II.

  9. Design of a saturated analogue and digital current transducer

    Pross, Alexander

    2002-01-01

    This project describes the development of a new analogue and digital current transducer, providing a range of new theoretical design methods for these novel devices. The main control feature is the limit cycling operation, and the novel use of the embedded sigma-delta modulator sensor structure to derive a low component count digital sensor. The research programme was initiated into the design, development and evaluation of a novel non-Hall sensing analogue and digital current transducer. These transducers are used for measurement of high currents in power systems applications. The investigation is concerned with a new design which uses a magnetic ferrite core without an air gap for current measurement. The motivation for this work was to design a new control circuit which provides a low component count, and utilises the non-linear properties of the magnetic ferrite core to transmit direct current. The use of a limit cycle control circuit was believed to be particularly suitable for the analogue and digital transducers, for two main reasons: the low component count, and the output signal is directly digital. In line with the motivations outlined above, the outcome of the research has witnessed the design, development and evaluation of a practically realisable analogue and digital current transducer. The design procedure, which is documented in this thesis, is considered to be a major contribution to the field of transducers design and development using a control systems approach. Mathematical models for both analogue and digital transducers were developed and the resulting model based predictions were found to be in good agreement with measured results. Simplification of the new model sensing device was achieved by approximating the non-linear ferrite core using FFT analysis. This is also considered to be a significant contribution. The development analogue and digital current censors employed a sampled data control systems design and utilised limit cycling

  10. Digital Interior Design by Stailia Design Oy

    Lindroos, Jaana

    2017-01-01

    The objective of the thesis work is to research and create a web based service in a field of interior design. With my project, I am hoping to find out whether this kind of web service in the field of interior design can work in general and that the process together with the actual order form on internet is smooth from both customer and company point of view. The company has interior design related services but none entirely executed on the web. The target is to create a totally new service/pr...

  11. Minimization In Digital Design As A Meta-Planning Problem

    Ho, William P. C.; Wu, Jung-Gen

    1987-05-01

    In our model-based expert system for automatic digital system design, we formalize the design process into three sub-processes - compiling high-level behavioral specifications into primitive behavioral operations, grouping primitive operations into behavioral functions, and grouping functions into modules. Consideration of design minimization explicitly controls decision-making in the last two subprocesses. Design minimization, a key task in the automatic design of digital systems, is complicated by the high degree of interaction among the time sequence and content of design decisions. In this paper, we present an AI approach which directly addresses these interactions and their consequences by modeling the minimization prob-lem as a planning problem, and the management of design decision-making as a meta-planning problem.

  12. Interface design for digital courses

    Tabbers, H.; Kester, L.; Hummel, H.; Nadolski, R.; Jochems, W.; Merriënboer, J.; Koper, R.

    2003-01-01

    An important question in web-based education is how to deal with the design of the interface. What will the actual screen look like? Two main issues that are especially relevant for educational purposes are discussed, both from a Human-Computer Interaction and an Educational Psychology perspective.

  13. Digital Gaming and Sustainable Design

    Shahin Vassigh

    2012-10-01

    Full Text Available The American building industry is one of the major consumers of energy. Buildings use 39% of thetotal energy consumed in the United States, significantly impacting national energy demand andcontributing to global warming. The vast majority of architectural practice in US leads to construction of buildings with a little concern to sustainability leading to environmental degradation. Although the bulk of architecture practice continues to produce unsustainable buildings, there is growing stream of exemplary models of sustainable design. Examining the success of suchpractices leads into two a two-folded finding; first that achieving sustainable design is closelylinked to “integrated Design”1 - a type of practice in which various disciplines involved in building design work together to achieve efficiency and other synergetic benefits. Second is that theadvances in computing and simulation algorithms are paving the way to achieve “integrateddesign”. These technologies are enabling the designers to collaborate, visualize, foresee, andmodify building performance with relatively high accuracy. They are increasing used to analyze complex systems to achieve streamlined structures, reduce dependence on mechanical systems, produce more effective construction processes, and reduce waste.If such practices were to become widespread, the architectural education needs to be restructured.The traditional American architectural curriculum that is based on a schism between“design” and “technology” is inherently in conflict with the principal of integration. Though largescalereform of architectural curricula is a complex, ongoing, and difficult debate; producing teaching tools that can simulate integrated design can impact and promote an understanding of sustainable practice in architecture. The proposed paper will present the progress of a multi-disciplinary team of faculty who arecollectively working on the completion, implementation and evaluation

  14. Design of digital systems and devices

    Adamski, Marian; Wegrzyn, Marek

    2011-01-01

    This book includes a variety of design and test methods targeted on different digital devices, as well as different logic elements. The authors of the book represent such countries as Israel, Poland, Russia, and Ukraine. The book is divided by three main parts, including thirteen different Chapters.

  15. Evaluation of a new type of direct digital radiography machine ...

    Evaluation of a new type of direct digital radiography machine. ... Ease of use, anatomical coverage and tolerance to patient motion were advantages. ... to that of conventional radiographs, with limited fine detail visibility and penetration.

  16. Multimedia foundations core concepts for digital design

    Costello, Vic; Youngblood, Susan

    2012-01-01

    Understand the core concepts and skills of multimedia production and digital storytelling using text, graphics, photographs, sound, motion, and video. Then, put it all together using the skills that you have developed for effective project planning, collaboration, visual communication, and graphic design. Presented in full color with hundreds of vibrant illustrations, Multimedia Foundations trains you in the principles and skill sets common to all forms of digital media production, enabling you to create successful, engaging content, no matter what tools you are using. Companion website

  17. An Investigation of Digital Payment Platform Designs

    Kazan, Erol; Damsgaard, Jan

    2014-01-01

    This paper focuses on the triumph march of mobile phones that currently are annexing music players, navigation devices, and cameras as separate physical objects. The next target is set on payment. Through synthesizing available literature, we construct a framework for studying digital payment...... platforms that combines platform, technology and business design aspects. The framework is applied to conduct a comparative case study of digital payment platforms. Four types of market actors are considered: banks, mobile network operators, merchants, and startups, which are incumbents and disrupters....... By hosting third-party services, payment instruments are evolving from single-purpose to multi-functional ones. Our research extends existing payment literature from the MSP perspective to emphasize certain digital payment platform components, which impact strategies and complementary products....

  18. Design and Implementation of Direct Form FIR Filter

    Kumar, Hanny; Kumar, Kamal

    2016-01-01

    The research article presents the design of the direct form of the Finite Impulse Response (FIR) filter using VHDL programming language. Multimedia technology and broadband communication demand the low power and high performance design applications in Digital Signal Processing (DSP). The digital filters are most important element of the communication system and DSP. In the paper, 7 tap FIR filter is implemented in Xilinx 14.2 software and functionally simulated in Modelsim 10.1 b software. Th...

  19. Two applications of direct digital down converters in beam diagnostics

    Powers, Tom; Flood, Roger; Hovater, Curt; Musson, John

    2000-01-01

    The technologies of direct digital down converters, digital frequency synthesis, and digital signal processing are being used in many commercial applications. Because of this commercialization, the component costs are being reduced to the point where they are economically viable for large scale accelerator applications. This paper will discuss two applications of these technologies to beam diagnostics. In the first application the combination of direct digital frequency synthesis and direct digital down converters are coupled with digital signal processor technology in order to maintain the stable gain environment required for a multi-electrode beam position monitoring system. This is done by injecting a CW reference signal into the electronics as part of the front-end circuitry. In the second application direct digital down converters are used to provide a novel approach to the measurement of beam intensity using cavity current monitors. In this system a pair of reference signals are injected into the cavity through an auxiliary port. The beam current is then calculated as the ratio of the beam signal divided by the average of the magnitude of the two reference signals

  20. Digit ratio predicts sense of direction in women.

    Xiaoqian J Chai

    Full Text Available The relative length of the second-to-fourth digits (2D:4D has been linked with prenatal androgen in humans. The 2D:4D is sexually dimorphic, with lower values in males than females, and appears to correlate with diverse measures of behavior. However, the relationship between digit ratio and cognition, and spatial cognition in particular, has produced mixed results. In the present study, we hypothesized that spatial tasks separating cue conditions that either favored female or male strategies would examine this structure-function correlation with greater precision. Previous work suggests that males are better in the use of directional cues than females. In the present study, participants learned a target location in a virtual landscape environment, in conditions that contained either all directional (i.e., distant or compass bearing cues, or all positional (i.e., local, small objects cues. After a short delay, participants navigated back to the target location from a novel starting location. Males had higher accuracy in initial search direction than females in environments with all directional cues. Lower digit ratio was correlated with higher accuracy of initial search direction in females in environments with all directional cues. Mental rotation scores did not correlate with digit ratio in either males or females. These results demonstrate for the first time that a sex difference in the use of directional cues, i.e., the sense of direction, is associated with more male-like digit ratio.

  1. Digit ratio predicts sense of direction in women.

    Chai, Xiaoqian J; Jacobs, Lucia F

    2012-01-01

    The relative length of the second-to-fourth digits (2D:4D) has been linked with prenatal androgen in humans. The 2D:4D is sexually dimorphic, with lower values in males than females, and appears to correlate with diverse measures of behavior. However, the relationship between digit ratio and cognition, and spatial cognition in particular, has produced mixed results. In the present study, we hypothesized that spatial tasks separating cue conditions that either favored female or male strategies would examine this structure-function correlation with greater precision. Previous work suggests that males are better in the use of directional cues than females. In the present study, participants learned a target location in a virtual landscape environment, in conditions that contained either all directional (i.e., distant or compass bearing) cues, or all positional (i.e., local, small objects) cues. After a short delay, participants navigated back to the target location from a novel starting location. Males had higher accuracy in initial search direction than females in environments with all directional cues. Lower digit ratio was correlated with higher accuracy of initial search direction in females in environments with all directional cues. Mental rotation scores did not correlate with digit ratio in either males or females. These results demonstrate for the first time that a sex difference in the use of directional cues, i.e., the sense of direction, is associated with more male-like digit ratio.

  2. Edge-detect interpolation for direct digital periapical images

    Song, Nam Kyu; Koh, Kwang Joon

    1998-01-01

    The purpose of this study was to aid in the use of the digital images by edge-detect interpolation for direct digital periapical images using edge-deted interpolation. This study was performed by image processing of 20 digital periapical images; pixel replication, linear non-interpolation, linear interpolation, and edge-sensitive interpolation. The obtained results were as follows ; 1. Pixel replication showed blocking artifact and serious image distortion. 2. Linear interpolation showed smoothing effect on the edge. 3. Edge-sensitive interpolation overcame the smoothing effect on the edge and showed better image.

  3. Transceiver and system design for digital communications

    Bullock, Scott

    2009-01-01

    Now in a 3rd edition, this successful book provides an intuitive approach to transceiver design, allowing a broad spectrum of readers to understand the topics clearly. It covers a wide range of data link communication design techniques, including link budgets, dynamic range and system analysis of receivers and transmitters used in data link communications, digital modulation and demodulation techniques of phase-shift keyed and frequency hopped spread spectrum systems using phase diagrams, multipath, gain control, an intuitive approach to probability, jamming reduction method using various adap

  4. Design and construction of a digital Dermatoscope

    Rojas, E.; Stolik, S.; De la Rosa, J.; Espina, J.; Perez, M.

    2012-01-01

    This paper presents the design and construction of a digital dermatoscope. The system consists of a digital camera for image acquisition, a light source that uniformly illuminates the area of interest, a 10x magnification lens and a base to carry out the immersion technique. The operating principle consists on obtaining two magnified images of the pigmented lesion, the first illuminating with a white light source and the second with a near-infrared source. With the developed software, both images are overlap in order to get more features that help the dermatologist to diagnose malignant melanoma with more reliably and accurately. It was simulated for the used geometry the surface pattern of irradiation and it was developed a simulation software for any distribution of light emitting diodes irradiance. (Author)

  5. Digital Modeling and Shaping of Design Practices

    Reijonen, Satu

    This paper focuses on the role of digital modeling in shaping coordinative practices between architects and energy engineers in construction design. The paper presents a case study of the use of an energy performance calculation programme, a numeric digital modeling tool, that not only enables...... coordination between the two communities but also shapes coordinative practices around the emerging building. The paper draws on two interlinked strands of literature that have engaged in the role of material artefacts in the social: the entanglement of technology in organizing and management (Orlikowski 2000......, 2010), and the socio-material constructivist studies of technology (Akrich 1992, Akrich et al. 2000, Latour 1991). The programme influences the coordinative practices in following ways: it shapes the modus of interaction between energy engineers and architects and enforces particular jurisdictional...

  6. Direct digital temperature control of the A-1 nuclear reactor

    Karpeta, C.

    1975-01-01

    The application is described of one of the modern control methods for designing an experimental digital temperature control system for heavy water moderated gas cooled reactors. The synthesis of the optimal stochastic regulator for reactor control in the area of the rated steady state was carried out using the method of dynamic programming and the Kalman filter technique. The analysis of the feedback circuit was conducted using control simulation on a universal digital computer. Results and experience are summed up. (author)

  7. Indigenous design and development of digital ASICs

    Misra, M.K.; Kishore, G.V.; Sridhar, N.; Palanisami, K.; Thirugnana Murthy, D.

    2013-01-01

    FPGAs and CPLDs were extensively used for the design and development of Instrumentation and Control systems including safety systems of Prototype Fast Breeder Reactor (PFBR). The developed I and C systems have been tested extensively for their functionality and also undergone various qualification tests. Some of these I and C systems have also been deployed in Fast Breeder Test Reactor. The performance of these designs is found to be satisfactory. However FPGAs/CPLDs are rapidly evolving and the devices become obsolete in a short span of time (typically about 5 to 8 years), whereas reactor's life time is typically about 40 years. This obsolescence problem can be handled in different ways. This paper discusses design and fabrication of digital ASICs as one of the alternate for handling obsolescence problems. Aim of this development work is to establish complete digital ASIC design, fabrication and testing flow, so that the same can be used in some of the critical/strategic requirements. (author)

  8. The Challenges of Designing Digital Services for Multiple Mobile Platforms

    Ghazawneh, Ahmad

    2016-01-01

    on a multiple case study of three mobile application development firms from Sweden, Denmark and Norway, we synthesize the digital service design taxonomy to understand the challenges faced by third-party developers. Our study identifies a set of challenges in four different levels: user level, platform level...... to tap into and join the digital ecosystem. However, while there is an emerging literature on designing digital services, little empirical evidence exists about challenges faced by third-party developers while designing digital services, and in particular for multiple mobile platforms. Drawing......The value of digital services is increasingly recognized by owners of digital platforms. These services have central role in building and sustaining the business of the digital platform. In order to sustain the design of digital services, owners of digital platforms encourage third-party developers...

  9. Combating obsolescence - ACR digital control systems design

    Tikku, S.; Raiskums, G.

    2006-01-01

    The ever increasing use of digital technologies and products to meet the control, automation and monitoring needs of the nuclear power plant - even though justified by the benefits it provides - comes with an increased risk of technological obsolescence happening through the course of the plant life. Some well considered strategies are being employed in the ACR design process to minimise this risk and alleviate the consequence if it happens. These include application of a modular overall architecture, adoption of international widely accepted standards to harmonise equipment qualification and software practices, production of control functional specifications that are not influenced by target platform, and careful selection of technologies and products. (author)

  10. Digital Design with KP-Lab

    D. Ponta

    2007-08-01

    Full Text Available KP-Lab is an EU Integrated Project envisioning a learning system that facilitates innovative practices of sharing, creating and working with knowledge in education and workplaces. The project exploits a novel pedagogical view, the knowledge-creation metaphor of learning. According to such “trialogical” approach, cognition arises through collaborative work in systematically developing shared “knowledge artefacts”, such as concepts, plans, material products, or social practices. The paper presents the plan of a pilot course to test the KP-Lab methodologies and tools in the field of Digital Design.

  11. Energy-aware design of digital systems

    Gruian, F.

    2000-02-01

    Power and energy consumption are important issues in many digital applications, for reasons such as packaging cost and battery life-span. With the development of portable computing and communication, an increasing number of research groups are addressing power and energy related issues at various stages during the design process. Most of the work done in this area focuses on lower abstraction levels, such as gate or transistor level. Ideally, a power and energy-efficient design flow should consider the power and energy issues at every stage in the design process. Therefore, power and energy aware methods, applicable early in the design process are required. In this trend, the thesis presents two high-level design methods addressing power and energy consumption minimization. The first of the two approaches we describe, targets power consumption minimization during behavioral synthesis. This is carried out by minimizing the switching activity, while taking the correlations between signals into account. The second approach performs energy consumption minimization during system-level design, by choosing the most energy-efficient schedule and configuration of resources. Both methods make use of the constraint programming paradigm to model the problems in an elegant manner. The experimental results presented in this thesis show the impact of addressing the power and energy related issues early in the design process.

  12. Device for direct digitized radiology of small objects

    Thomas, G.; Favier, C.; Brebant, C.; Mogavero, R.

    1983-06-01

    A radiological device has been developed to obtain direct digitized views with a large integration time. A micro computer system with programs specially developed for the automatic materials defects evaluation is used. Some results concerning the weldings of electro-nuclear fuel pins are presented here [fr

  13. Design and Fabrication of Aerospace-Grade Digital Composite Materials

    National Aeronautics and Space Administration — This project aims to advance design rules and fabrication approaches to create aerospace-grade structures from digital composite materials. Digital materials are...

  14. Revolution of Nuclear Power Plant Design Through Digital Technology

    Zhang, L.; Shi, J.; Chen, W.

    2015-01-01

    In the digital times, digital technology has penetrated into every industry. As the highest safety requirement standard, nuclear power industry needs digital technology more to breed high quality and efficiency. Digital power plant is derived from digital design and the digitisation of power plant transfer is an inevitable trend. This paper introduces the technical solutions and features of digital nuclear power plant construction by Shanghai Nuclear Engineering Research & Design Institute, points out the key points and technical difficulties that exist in the process of construction and can serve as references for further promoting construction of digital nuclear power plant. Digital technology is still flourishing. Although many problems will be encountered in construction, it is believed that digital technology will make nuclear power industry more safe, cost-effective and efficient. (author)

  15. Effective dose from direct and indirect digital panoramic units

    Lee, Gun Sun; Kim, Jin Soo; Seo, Yo Seob; Kim, Jae Duk [School of Dentistry, Oral Biology Research Institute, Chosun University, Gwangju (Korea, Republic of)

    2013-06-15

    This study aimed to provide comparative measurements of the effective dose from direct and indirect digital panoramic units according to phantoms and exposure parameters. Dose measurements were carried out using a head phantom representing an average man (175 cm tall, 73.5 kg male) and a limbless whole body phantom representing an average woman (155 cm tall, 50 kg female). Lithium fluoride thermoluminescent dosimeter (TLD) chips were used for the dosimeter. Two direct and 2 indirect digital panoramic units were evaluated in this study. Effective doses were derived using 2007 International Commission on Radiological Protection (ICRP) recommendations. The effective doses of the 4 digital panoramic units ranged between 8.9 {mu}Sv and 37.8 {mu}Sv. By using the head phantom, the effective doses from the direct digital panoramic units (37.8 {mu}Sv, 27.6 {mu}Sv) were higher than those from the indirect units (8.9 {mu}Sv, 15.9 {mu}Sv). The same panoramic unit showed the difference in effective doses according to the gender of the phantom, numbers and locations of TLDs, and kVp. To reasonably assess the radiation risk from various dental radiographic units, the effective doses should be obtained with the same numbers and locations of TLDs, and with standard hospital exposure. After that, it is necessary to survey the effective doses from various dental radiographic units according to the gender with the corresponding phantom.

  16. Direct drive digital servo press with high parallel control

    Murata, Chikara; Yabe, Jun; Endou, Junichi; Hasegawa, Kiyoshi

    2013-12-01

    Direct drive digital servo press has been developed as the university-industry joint research and development since 1998. On the basis of this result, 4-axes direct drive digital servo press has been developed and in the market on April of 2002. This servo press is composed of 1 slide supported by 4 ball screws and each axis has linearscale measuring the position of each axis with high accuracy less than μm order level. Each axis is controlled independently by servo motor and feedback system. This system can keep high level parallelism and high accuracy even with high eccentric load. Furthermore the 'full stroke full power' is obtained by using ball screws. Using these features, new various types of press forming and stamping have been obtained by development and production. The new stamping and forming methods are introduced and 'manufacturing' need strategy of press forming with high added value and also the future direction of press forming are also introduced.

  17. Remediating a Design Tool: Implications of Digitizing Sticky Notes

    Jensen, Mads Møller; Rädle, Roman; Klokmose, Clemens Nylandsted

    2018-01-01

    digital sticky notes setup. The paper contributes with a nuanced understanding of what happens when remediating a physical design tool into digital space, by emphasizing focus shifts and breakdowns caused by the technology, but also benefits and promises inherent in the digital media. Despite users...... their use and understanding, yielding new concerns regarding cross-device transfer and collaboration....

  18. Sketchtube; integrating digital media in the education of design skills

    Mulder-Nijkamp, Maaike; Eggink, Wouter

    2013-01-01

    In this paper we discuss the application of new opportunities and chances of digital learning in design education by means of the implementation of a digital sketching forum into a sketching course. The so called ‘blended learning’ method combines face to face education and a digital forum called

  19. Pre-Service Teachers Designing and Constructing "Good Digital Games"

    Artym, Corbett; Carbonaro, Mike; Boechler, Patricia

    2016-01-01

    There is a growing interest in the application of digital games to enhance learning across many educational levels. This paper investigates pre-service teachers' ability to operationalize the learning principles that are considered part of a good digital game (Gee, 2007) by designing digital games in Scratch. Forty pre-service teachers, enrolled…

  20. Practical design of digital circuits basic logic to microprocessors

    Kampel, Ian

    1983-01-01

    Practical Design of Digital Circuits: Basic Logic to Microprocessors demonstrates the practical aspects of digital circuit design. The intention is to give the reader sufficient confidence to embark upon his own design projects utilizing digital integrated circuits as soon as possible. The book is organized into three parts. Part 1 teaches the basic principles of practical design, and introduces the designer to his """"tools"""" - or rather, the range of devices that can be called upon. Part 2 shows the designer how to put these together into viable designs. It includes two detailed descriptio

  1. Digital PCR for direct quantification of viruses without DNA extraction

    Pav?i?, Jernej; ?el, Jana; Milavec, Mojca

    2015-01-01

    DNA extraction before amplification is considered an essential step for quantification of viral DNA using real-time PCR (qPCR). However, this can directly affect the final measurements due to variable DNA yields and removal of inhibitors, which leads to increased inter-laboratory variability of qPCR measurements and reduced agreement on viral loads. Digital PCR (dPCR) might be an advantageous methodology for the measurement of virus concentrations, as it does not depend on any calibration mat...

  2. A direct-view customer-oriented digital holographic camera

    Besaga, Vira R.; Gerhardt, Nils C.; Maksimyak, Peter P.; Hofmann, Martin R.

    2018-01-01

    In this paper, we propose a direct-view digital holographic camera system consisting mostly of customer-oriented components. The camera system is based on standard photographic units such as camera sensor and objective and is adapted to operate under off-axis external white-light illumination. The common-path geometry of the holographic module of the system ensures direct-view operation. The system can operate in both self-reference and self-interference modes. As a proof of system operability, we present reconstructed amplitude and phase information of a test sample.

  3. Digital Production and Students as Learning Designers

    Sørensen, Birgitte Holm; Levinsen, Karin

    2014-01-01

    Today’s digitalization allows users to interact, collaborate, communicate and create user-generated content. The technology is intuitive and easy to use even for young children, and new learning opportunities emerge. Particularly, students’ production as a learning form benefits from digitalization...

  4. Interweaving digitality in the fabric of design

    De Roeck, D.A.J.; Standaert, A.; Paauwe, R.A.; Verwulgen, S.; Baelus, C.; Stappers, P.J.

    2012-01-01

    Products that embrace and integrate an invisible, digital world are appearing around us in a rapid pace.This emerging type of products introduces a new dynamic between people, objects and the context oruse. The integration of embedded, pervasive and digital technologies in products imposes

  5. Direct digital control of furnaces irradiated in nuclear reactors

    Joumard, R.

    1969-01-01

    An experimental direct digital control system has been realised in the 'C.E.N.G.', in order to verify that a computer makes easier the control of the experiments done in the nuclear reactors and to solve the theoretical and technical difficulties. The regulation is applied to thermal processes. The sampled data systems theory permits to choose the type of an efficient and simple digital compensator, and to establish a diagram which gives the values of the correcting parameters (obtained by minimizing the difference between the output and the input when perturbations occur). The programme execute, in simultaneity, supervision and regulation. Complex possibilities of printing out measures and alarms existed. The computer works out an incremental correction which makes step motors to turn. These motors act on the heating organs. The theoretical values and answers have been confirmed. The accuracy was limited essentially by the input quantification (1/1000 th). The comfort of such a system has been noticeable. (author) [fr

  6. Design-based learning in classrooms using playful digital toolkits

    Scheltenaar, K.J.; van der Poel, J.E.C.; Bekker, Tilde

    2015-01-01

    The goal of this paper is to explore how to implement Design Based Learning (DBL) with digital toolkits to teach 21st century skills in (Dutch) schools. It describes the outcomes of a literature study and two design case studies in which such a DBL approach with digital toolkits was iteratively

  7. Design Principles of Next-Generation Digital Gaming for Education.

    Squire, Kurt; Jenkins, Henry; Holland, Walter; Miller, Heather; O'Driscoll, Alice; Tan, Katie Philip; Todd, Katie.

    2003-01-01

    Discusses the rapid growth of digital games, describes research at MIT that is exploring the potential of digital games for supporting learning, and offers hypotheses about the design of next-generation educational video and computer games. Highlights include simulations and games; and design principles, including context and using information to…

  8. Application of direct digital radiography of nasal bone

    Gao Dengfa; Wang Haijun; Zhang Ailian; Wang Yulin

    2005-01-01

    Objective: To research the application value of direct digital radiograph (DDR ) in nasal bone imaging. Methods: One hundred cases were examined by DDR, 30 cases of them were examined by two methods both DDR and conventional radiography. All digital images were post-processed with 'MUSICA' (Multi-Scale Image Contrast Amplification), incision and largamente, analyzed and diagnosed by experienced two radiologists and two technicians. Results: One hundred cases of nasal bone, soft tissue of nose were showed excellent in DDR, and satisfactory cases were 95 and 92, respectively. Forty-six cases of nasal bone fractures were found. Thirty cases were examined by both DDR and conventional radiography, images of nasal bone, soft tissue of nose were showed, satisfactory cases were 28 in DDR; and satisfactory cases were 6 (χ 2 =20.05, P 2 =15.06, P 2 =5.14, P<0.05) in conventional and digital radiography, respectively. Conclusion: DDR images of nasal bone, soft tissue of nose was excellent, more fractures were discovered than conventional radiography. Image quality of DDR is better than conventional radiography in nasal bone imaging. (authors)

  9. Innovation & evaluation of tangible direct manipulation digital drawing pens for children.

    Lee, Tai-Hua; Wu, Fong-Gong; Chen, Huei-Tsz

    2017-04-01

    Focusing on the theme of direct manipulation, in this study, we proposed a new and innovative tangible user interface (TUI) design concept for a manipulative digital drawing pen. Based on interviews with focus groups brainstorming and experts and the results of a field survey, we selected the most suitable tangible user interface for children between 4 and 7 years of age. Using the new tangible user interface, children could choose between the brush tools after touching and feeling the various patterns. The thickness of the brush could be adjusted by changing the tilt angle. In a subsequent experimental process we compared the differences in performance and subjective user satisfaction. A total of sixteen children, aged 4-7 years participated in the experiment. Two operating system experiments (the new designed tangible digital drawing pen and traditional visual interface-icon-clicking digital drawing pens) were performed at random and in turns. We assessed their manipulation performance, accuracy, brush stroke richness and subjective evaluations. During the experimental process we found that operating functions using the direct manipulation method, and adding shapes and semantic models to explain the purpose of each function, enabled the children to perform stroke switches relatively smoothly. By using direct manipulation digital pens, the children could improve their stroke-switching performance for digital drawing. Additionally, by using various patterns to represent different brushes or tools, the children were able to make selections using their sense of touch, thereby reducing the time required to move along the drawing pens and select icons (The significant differences (p = 0.000, p drawing thick lines using the crayon function of the two (new and old) drawing pens (new 5.8750 drawing operations enhanced the drawing results, thereby increasing the children's enjoyment of drawing with tangible digital drawing pens. Copyright © 2016 Elsevier Ltd. All

  10. Design and implementation of a digital clock showing digits in Bangla font using microcontroller AT89C4051

    Muslim, Nasif; Adnan, Md. Tanvir; Kabir, Mohammad Zahidul; Kabir, Md. Humayun; Islam, Sheikh Mominul

    2012-01-01

    In this paper, a digital clock is designed where the microcontroller is used for timing controller and the font of the Bangla digits are designed, and programmed within the microcontroller. The design is cost effective, simple and easy for maintenance.

  11. The Design Process and User Focused Digital Spaces

    Keating, Elaine M.

    2004-01-01

    This thesis presents a qualitative inquiry into how the graphic design process is being reconfigured within the new digital media landscape. The literature review looks at the historical relationship between graphic design and technology from the invention of the printing press to the personal computer and reviews how this relationship is again affected by the emergence of the computer as a medium for communication. The products of digital design are no longer static and fixed but are dynamic...

  12. Nonlinear machine learning and design of reconfigurable digital colloids.

    Long, Andrew W; Phillips, Carolyn L; Jankowksi, Eric; Ferguson, Andrew L

    2016-09-14

    Digital colloids, a cluster of freely rotating "halo" particles tethered to the surface of a central particle, were recently proposed as ultra-high density memory elements for information storage. Rational design of these digital colloids for memory storage applications requires a quantitative understanding of the thermodynamic and kinetic stability of the configurational states within which information is stored. We apply nonlinear machine learning to Brownian dynamics simulations of these digital colloids to extract the low-dimensional intrinsic manifold governing digital colloid morphology, thermodynamics, and kinetics. By modulating the relative size ratio between halo particles and central particles, we investigate the size-dependent configurational stability and transition kinetics for the 2-state tetrahedral (N = 4) and 30-state octahedral (N = 6) digital colloids. We demonstrate the use of this framework to guide the rational design of a memory storage element to hold a block of text that trades off the competing design criteria of memory addressability and volatility.

  13. Digital PCR for direct quantification of viruses without DNA extraction.

    Pavšič, Jernej; Žel, Jana; Milavec, Mojca

    2016-01-01

    DNA extraction before amplification is considered an essential step for quantification of viral DNA using real-time PCR (qPCR). However, this can directly affect the final measurements due to variable DNA yields and removal of inhibitors, which leads to increased inter-laboratory variability of qPCR measurements and reduced agreement on viral loads. Digital PCR (dPCR) might be an advantageous methodology for the measurement of virus concentrations, as it does not depend on any calibration material and it has higher tolerance to inhibitors. DNA quantification without an extraction step (i.e. direct quantification) was performed here using dPCR and two different human cytomegalovirus whole-virus materials. Two dPCR platforms were used for this direct quantification of the viral DNA, and these were compared with quantification of the extracted viral DNA in terms of yield and variability. Direct quantification of both whole-virus materials present in simple matrices like cell lysate or Tris-HCl buffer provided repeatable measurements of virus concentrations that were probably in closer agreement with the actual viral load than when estimated through quantification of the extracted DNA. Direct dPCR quantification of other viruses, reference materials and clinically relevant matrices is now needed to show the full versatility of this very promising and cost-efficient development in virus quantification.

  14. Designing digital health information in a health literacy context

    Meppelink, C.S.

    2016-01-01

    Digital health information is widely available, but not everyone fully benefits due to limited health literacy. Until now, little was known about how health literacy influences information processing and how design features of digital health information can be used to create optimal health messages

  15. Foundations of Digital Methods : Query Design

    Rogers, R.; Schäfer, M.T.; van Es, K.

    2017-01-01

    Broadly speaking digital methods may be considered the deployment of online tools and data for the purposes of social and medium research. More speci cally, they derive from online methods, or methods of the medium, which are reimagined and repurposed for research. The methods to be repurposed are

  16. The Direct Digital Modulation of Traveling Wave Tubes

    Radhamohan, Ranjan S.

    2004-01-01

    Traveling wave tube (TWT) technology, first described by Rudolf Kompfner in the early 1940s, has been a key component of space missions from the earliest communication satellites in the 1960s to the Cassini probe today. TWTs are essentially signal amplifiers that have the special capability of operating at microwave frequencies. The microwave frequency range, which spans from approximately 500 MHz to 300 GHz, is shared by many technologies including cellular phones, satellite television, space communication, and radar. TWT devices are superior in reliability, weight, and efficiency to solid-state amplifiers at the high power and frequency levels required for most space missions. TWTs have three main components -an electron gun, slow wave structure, and collector. The electron gun generates an electron beam that moves along the length of the tube axis, inside of the slow wave circuit. At the same time, the inputted signal is slowed by its travel through the coils of the helical slow wave circuit. The interaction of the electron beam and this slowed signal produces a transfer of kinetic energy to the signal, and in turn, amplification. At the end of its travel, the spent electron beam moves into the collector where its remaining energy is dissipated as heat or harnessed for reuse. TWTs can easily produce gains in the tens of decibels, numbers that are suitable for space missions. To date, however, TWTs have typically operated at fixed levels of gain. This gain is determined by various, unchanging, physical factors of the tube. Traditionally, to achieve varying gain, an input signal s amplitude has had to first be modulated by a separate device before being fed into the TWT. This is not always desirable, as significant distortion can occur in certain situations. My mentor, Mr. Dale Force, has proposed an innovative solution to this problem called direct digital modulation . The testing and implementation of this solution is the focus of my summer internship. The

  17. Digital integrated circuit design using Verilog and SystemVerilog

    Mehler, Ronald W

    2014-01-01

    For those with a basic understanding of digital design, this book teaches the essential skills to design digital integrated circuits using Verilog and the relevant extensions of SystemVerilog. In addition to covering the syntax of Verilog and SystemVerilog, the author provides an appreciation of design challenges and solutions for producing working circuits. The book covers not only the syntax and limitations of HDL coding, but deals extensively with design problems such as partitioning and synchronization, helping you to produce designs that are not only logically correct, but will actually

  18. Attending to others: how digital technologies direct young people's nightlife

    J. Truong

    2018-05-01

    Full Text Available It is a growing phenomenon that young people use mobile information and communication technologies during their nightlife. This article offers an empirical examination of how young people's nightlife is shaped by engagement with the mobile phone application WhatsApp. Drawing on Sara Ahmed's phenomenological concept of orientation, I examine how WhatsApp extends young people's nightlife and how young people become orientated therein. On the one hand, I show that nightlife acquires new boundaries and fixities that encourage young people to direct their attention towards missing social relations and absent nightlife places. On the other hand, I find that young people create new perceptions of how to inhabit and spend leisure time and space. I argue that digital technologies reorientate young people, which I suggest offers novel means of addressing young people's contemporary nightlife practices, places, spaces, and social relations.

  19. ETF design activities: status and future direction

    Steiner, D.

    1980-01-01

    The nature of the device to follow TFTR has been evolving over the past six years. The most recent design activities have been directed to the Engineering Test Facility (ETF) concept. In order to address the design of the ETF a centralized laboratory/industry design team was established and hosted at ORNL. This Design Center began ETF Preconceptual design in October, 1979. The ETF design effort has been judged to be sound. However, the ETF mission has been judged to be overly ambitious. It has been recommended that the device to follow TFTR be dedicated to the investigation of engineering feasibility and that device has been designated the Fusion Engineering Device (FED). The ETF design activities provide a basis for developing the FED design. This will be accomplished under the direction of the newly formed FED Technical Management Board

  20. Digital sonar design in underwater acoustics principles and applications

    Li, Qihu

    2012-01-01

    "Digital Sonar Design in Underwater Acoustics Principles and Applications" provides comprehensive and up-to-date coverage of research on sonar design, including the basic theory and techniques of digital signal processing, basic concept of information theory, ocean acoustics, underwater acoustic signal propagation theory, and underwater signal processing theory. This book discusses the general design procedure and approaches to implementation, the design method, system simulation theory and techniques, sonar tests in the laboratory, lake and sea, and practical validation criteria and methods for digital sonar design. It is intended for researchers in the fields of underwater signal processing and sonar design, and also for navy officers and ocean explorers. Qihu Li is a professor at the Institute of Acoustics, Chinese Academy of Sciences, and an academician of the Chinese Academy of Sciences.

  1. Software Defined Radio (SDR and Direct Digital Synthesizer (DDS for NMR/MRI Instruments at Low-Field

    Aktham Asfour

    2013-11-01

    Full Text Available A proof-of-concept of the use of a fully digital radiofrequency (RF electronics for the design of dedicated Nuclear Magnetic Resonance (NMR systems at low-field (0.1 T is presented. This digital electronics is based on the use of three key elements: a Direct Digital Synthesizer (DDS for pulse generation, a Software Defined Radio (SDR for a digital receiving of NMR signals and a Digital Signal Processor (DSP for system control and for the generation of the gradient signals (pulse programmer. The SDR includes a direct analog-to-digital conversion and a Digital Down Conversion (digital quadrature demodulation, decimation filtering, processing gain…. The various aspects of the concept and of the realization are addressed with some details. These include both hardware design and software considerations. One of the underlying ideas is to enable such NMR systems to “enjoy” from existing advanced technology that have been realized in other research areas, especially in telecommunication domain. Another goal is to make these systems easy to build and replicate so as to help research groups in realizing dedicated NMR desktops for a large palette of new applications. We also would like to give readers an idea of the current trends in this field. The performances of the developed electronics are discussed throughout the paper. First FID (Free Induction Decay signals are also presented. Some development perspectives of our work in the area of low-field NMR/MRI will be finally addressed.

  2. Software Defined Radio (SDR) and Direct Digital Synthesizer (DDS) for NMR/MRI Instruments at Low-Field

    Asfour, Aktham; Raoof, Kosai; Yonnet, Jean-Paul

    2013-01-01

    A proof-of-concept of the use of a fully digital radiofrequency (RF) electronics for the design of dedicated Nuclear Magnetic Resonance (NMR) systems at low-field (0.1 T) is presented. This digital electronics is based on the use of three key elements: a Direct Digital Synthesizer (DDS) for pulse generation, a Software Defined Radio (SDR) for a digital receiving of NMR signals and a Digital Signal Processor (DSP) for system control and for the generation of the gradient signals (pulse programmer). The SDR includes a direct analog-to-digital conversion and a Digital Down Conversion (digital quadrature demodulation, decimation filtering, processing gain…). The various aspects of the concept and of the realization are addressed with some details. These include both hardware design and software considerations. One of the underlying ideas is to enable such NMR systems to “enjoy” from existing advanced technology that have been realized in other research areas, especially in telecommunication domain. Another goal is to make these systems easy to build and replicate so as to help research groups in realizing dedicated NMR desktops for a large palette of new applications. We also would like to give readers an idea of the current trends in this field. The performances of the developed electronics are discussed throughout the paper. First FID (Free Induction Decay) signals are also presented. Some development perspectives of our work in the area of low-field NMR/MRI will be finally addressed. PMID:24287540

  3. On the Integration of Digital Design and Analysis Tools

    Klitgaard, Jens; Kirkegaard, Poul Henning

    2006-01-01

    The aim of this research is to look into integrated digital design and analysis tools in order to find out if it is suited for use by architects and designers or only by specialists and technicians - and if not, then to look at what can be done to make them more available to architects and design...

  4. A digital receiver module with direct data acquisition for magnetic resonance imaging systems.

    Tang, Weinan; Sun, Hongyu; Wang, Weimin

    2012-10-01

    A digital receiver module for magnetic resonance imaging (MRI) with detailed hardware implementations is presented. The module is based on a direct sampling scheme using the latest mixed-signal circuit design techniques. A single field-programmable gate array chip is employed to perform software-based digital down conversion for radio frequency signals. The modular architecture of the receiver allows multiple acquisition channels to be implemented on a highly integrated printed circuit board. To maintain the phase coherence of the receiver and the exciter in the context of direct sampling, an effective phase synchronization method was proposed to achieve a phase deviation as small as 0.09°. The performance of the described receiver module was verified in the experiments for both low- and high-field (0.5 T and 1.5 T) MRI scanners and was compared to a modern commercial MRI receiver system.

  5. Experimental direct digital control of the power plant A1 reactor based on a modern control theory approach

    Karpeta, C.

    1979-01-01

    The objective of the project was to accumulate technical experience with application of modern control theory in nuclear power by carrying out a case study of an experimental direct digital control at the A1 reactor about its nominal steady state. The research has proved that slightly modified method of solution of the linear stochastic regulator problem can be successfully applied in design of digital control system of nuclear power reactors

  6. Design type testing for digital instrumentation and control systems

    Bastl, W.; Mohns, G.

    1997-01-01

    The design type qualification of digital safety instrumentation and control is outlined. Experience shows that the concepts discussed, derived from codes, guidelines and standards, achieve useful results. It has likewise become clear that the systematics of design type qualification of the hardware components is also applicable to the software components. Design type qualification of the software, a premiere, could be performed unexpectedly smoothly. The hardware design type qualification proved that the hardware as a substrate of functionality and reliability is an issue that demands full attention, as compared to conventional systems. Another insight is that design qualification of digital instrumentation and control systems must include plant-independent systems tests. Digital instrumentation and control systems simply work very differently from conventional control systems, so that this testing modality is inevitable. (Orig./CB) [de

  7. Designing for Dialogue and Digitality in Higher and Continuing Education

    Sorensen, Elsebeth Korsgaard; Kjærgaard, Thomas

    2016-01-01

    for studying these design aspects is constituted by learning designs from, both a University context and a University College context. The findings and discussion resulting from the analysis suggest that a meta-communicative learning-to-learn (L2L) approach to dialogue in the pedagogic aspects of the learning...... design may be fruitful in highlighting and promoting the establishment and maintenance of a collaborative digital dialogue that is conducive to deep learning in digital CoPs unfolding in VLEs. Consequently, we suggest development of hybrid designs that synthesise the dialogical advantages of online......This study investigates and contrasts three scenarios of further education; presence lessons and two types of blended learning. It addresses the conceptual challenge of creating learning designs for online learning communities of practice (COPs) with a focus on 'collaborative digital dialogue...

  8. The multiplicity of the digital textbook as design object

    Riis Ebbesen, Toke

    2015-01-01

    Building on a preliminary case study of the Danish educational publisher Systime A/S and its flagship product, the web-based ‘iBog’/‘iBook’, this article explores how digital textbooks can be understood as design. The shaping of digital books is seen as being intertwined in a wider circuit...... reorganization of the publishing company, web-based user interfaces, and ultimately the branding, which market these new digital objects, are building power- ful discourses around the product. Thus it is suggested that the design process of the iBog case can be understood in a model of database-based publishing...... with multiple levels. In the final analysis, the iBog is much more than a product and a technology. It is a brand that goes beyond what can be studied by looking at the digital textbook as a singular artefact....

  9. Event-Triggered Distributed Average Consensus Over Directed Digital Networks With Limited Communication Bandwidth.

    Li, Huaqing; Chen, Guo; Huang, Tingwen; Dong, Zhaoyang; Zhu, Wei; Gao, Lan

    2016-12-01

    In this paper, we consider the event-triggered distributed average-consensus of discrete-time first-order multiagent systems with limited communication data rate and general directed network topology. In the framework of digital communication network, each agent has a real-valued state but can only exchange finite-bit binary symbolic data sequence with its neighborhood agents at each time step due to the digital communication channels with energy constraints. Novel event-triggered dynamic encoder and decoder for each agent are designed, based on which a distributed control algorithm is proposed. A scheme that selects the number of channel quantization level (number of bits) at each time step is developed, under which all the quantizers in the network are never saturated. The convergence rate of consensus is explicitly characterized, which is related to the scale of network, the maximum degree of nodes, the network structure, the scaling function, the quantization interval, the initial states of agents, the control gain and the event gain. It is also found that under the designed event-triggered protocol, by selecting suitable parameters, for any directed digital network containing a spanning tree, the distributed average consensus can be always achieved with an exponential convergence rate based on merely one bit information exchange between each pair of adjacent agents at each time step. Two simulation examples are provided to illustrate the feasibility of presented protocol and the correctness of the theoretical results.

  10. Design of a laser scanner for a digital mammography system.

    Rowlands, J A; Taylor, J E

    1996-05-01

    We have developed a digital readout system for radiographic images using a scanning laser beam. In this system, electrostatic charge images on amorphous selenium (alpha-Se) plates are read out using photo-induced discharge (PID). We discuss the design requirements of a laser scanner for the PID system and describe its construction from commercially available components. The principles demonstrated can be adapted to a variety of digital imaging systems.

  11. Teaching children digital literacy through design-based learning with digital toolkits in schools

    Bekker, T.; Bakker, S.; Douma, I.; van der Poel, J.E.C.; Scheltenaar, K.J.

    2015-01-01

    The paper presents our work on how to teach digital literacy and design thinking to children at primary and secondary schools, with a particular focus on exploring the tools that may support children’s learning in these domains. We have conducted design explorations with input from diverse

  12. InDesign CC digital classroom

    Smith, Christopher

    2013-01-01

    Learn the newest version of Adobe's premiere page design software-InDesign CC- with this complete package Written by a team of expert instructors, this complete book-and-DVD package teaches even the most inexperienced beginner how to design eye-popping layouts for brochures, magazines, e-books, and flyers. Step-by-step instructions in the full-color book are enhanced by video tutorials on the companion DVD. Thirteen self-paced lessons let you learn Adobe InDesign CC (Creative Cloud) at your own speed; it's like having your own personal tutor teaching you the hottest new version of this leadi

  13. Digital-Visual-Sensory-Design Anthropology: Ethnography, Imagination and Intervention

    Pink, Sarah

    2014-01-01

    In this article I outline how a digital-visual-sensory approach to anthropological ethnography might participate in the making of relationship between design and anthropology. While design anthropology is itself coming of age, the potential of its relationship with applied visual anthropology methodology and theory has not been considered in the…

  14. Foundations of digital signal processing theory, algorithms and hardware design

    Gaydecki, Patrick

    2005-01-01

    An excellent introductory text, this book covers the basic theoretical, algorithmic and real-time aspects of digital signal processing (DSP). Detailed information is provided on off-line, real-time and DSP programming and the reader is effortlessly guided through advanced topics such as DSP hardware design, FIR and IIR filter design and difference equation manipulation.

  15. Design patterns for digital item types in higher education

    Draaijer, S.; Hartog, R.J.M.

    2007-01-01

    A set of design patterns for digital item types has been developed in response to challenges identified in various projects by teachers in higher education. The goal of the projects in question was to design and develop formative and summative tests, and to develop interactive learning material in

  16. Geothermal direct use engineering and design guidebook

    Lienau, P.J.; Lunis, B.C.

    1991-01-01

    The Geothermal Direct Use Engineering and Design Guidebook is designed to be a comprehensive, thoroughly practical reference guide for engineers and designers of direct heat projects. These projects could include the conversion of geothermal energy into space heating and cooling of buildings, district heating, greenhouse heating, aquaculture and industrial processing. The Guidebook is directed at understanding the nature of geothermal resources and the exploration of the resources, fluid sampling techniques, drilling, and completion of geothermal wells through well testing, and reservoir evaluation. It presents information useful to engineers on the specification of equipment including well pumps, piping, heat exchangers, space heating equipment, heat pumps and absorption refrigeration. A compilation of current information about greenhouse aquaculture and industrial applications is included together with a discussion of engineering cost analysis, regulation requirements, and environmental consideration. The purpose of the Guidebook is to provide an integrated view for the development of direct use projects for which there is a very large potential in the United States

  17. Geothermal direct use engineering and design guidebook

    Lienau, P.J.; Lunis, B.C. (eds.)

    1991-01-01

    The Geothermal Direct Use Engineering and Design Guidebook is designed to be a comprehensive, thoroughly practical reference guide for engineers and designers of direct heat projects. These projects could include the conversion of geothermal energy into space heating and cooling of buildings, district heating, greenhouse heating, aquaculture and industrial processing. The Guidebook is directed at understanding the nature of geothermal resources and the exploration of the resources, fluid sampling techniques, drilling, and completion of geothermal wells through well testing, and reservoir evaluation. It presents information useful to engineers on the specification of equipment including well pumps, piping, heat exchangers, space heating equipment, heat pumps and absorption refrigeration. A compilation of current information about greenhouse aquaculture and industrial applications is included together with a discussion of engineering cost analysis, regulation requirements, and environmental consideration. The purpose of the Guidebook is to provide an integrated view for the development of direct use projects for which there is a very large potential in the United States.

  18. Geothermal direct use engineering and design guidebook

    Bloomquist, R.G.; Culver, G.; Ellis, P.F.; Higbee, C.; Kindle, C.; Lienau, P.J.; Lunis, B.C.; Rafferty, K.; Stiger, S.; Wright, P.M.

    1989-03-01

    The Geothermal Direct Use Engineering and Design Guidebook is designed to be a comprehensive, thoroughly practical reference guide for engineers and designers of direct heat projects. These projects could include the conversion of geothermal energy into space heating cooling of buildings, district heating, greenhouse heating, aquaculture and industrial processing. The Guidebook is directed at understanding the nature of geothermal resources and the exploration of these resources, fluid sampling techniques, drilling, and completion of geothermal wells through well testing, and reservoir evaluation. It presents information useful to engineers on the specification of equipment including well pumps, piping, heat exchangers, space heating equipment, heat pumps and absorption refrigeration. A compilation of current information about greenhouse, aquaculture and industrial applications is included together with a discussion of engineering cost analysis, regulation requirements, and environmental considerations. The purpose of the Guidebook is to provide an integrated view for the development of direct use projects for which there is a very potential in the United States.

  19. Direct digital acquisition of neonatal portable chest radiographs

    Cohen, M.D.; Cory, D.A.; Broderick, N.J.; Smith, J.A.

    1987-01-01

    The Philips computerized radiography system utilizes a phosphor plate instead of an x-ray film to acquire radiographic images. The latent image on the plate is converted to a digital format. The authors report their initial experience with the system in more than 300 studies on intensive care neonates. The digital images provide very uniform image density. Tubes and catheters are more easily visualized than on conventional images. Soft tissues of the chest wall and bony structures are also more clearly seen on the digital images. The authors' initial experience indicates that portable digital imaging of neonates is technically feasible and provides good-quality diagnostic images

  20. Design of a rear anamorphic attachment for digital cinematography

    Cifuentes, A.; Valles, A.

    2008-09-01

    Digital taking systems for HDTV and now for the film industry present a particularly challenging design problem for rear adapters in general. The thick 3-channel prism block in the camera provides an important challenge in the design. In this paper the design of a 1.33x rear anamorphic attachment is presented. The new design departs significantly from the traditional Bravais condition due to the thick dichroic prism block. Design strategies for non-rotationally symmetric systems and fields of view are discussed. Anamorphic images intrinsically have a lower contrast and less resolution than their rotationally symmetric counterparts, therefore proper image evaluation must be considered. The interpretation of the traditional image quality methods applied to anamorphic images is also discussed in relation to the design process. The final design has a total track less than 50 mm, maintaining the telecentricity of the digital prime lens and taking full advantage of the f/1.4 prism block.

  1. Compound Half-Backed Weave Design For Digital Jacquard Fabric

    Zhang, Meng; Zhou, Jiu

    2017-12-01

    Based on layered-combination design mode and compound structure, this paper presents a design method, named compound half-backed weave in order to achieve innovating weave structure and surface effect of fabric. This design method includes primary weaves chosen, half-backed technical points set up and half-backed weave databases established. The fabric produced using compound half-backed weave designed by this method can exhibit a unique half-backed effect that only half of the threads on the fabric surface remain in a state of being covered by adjacent wefts. Compound half-backed weave can not only meets the design need of jacquard fabric with different digital images and effectively improves the efficiency of structural design, but also puts forward new theory and method for innovative design of digital jacquard fabric.

  2. Digital design of multimaterial photonic particles

    Tao, Guangming; Kaufman, Joshua J.; Shabahang, Soroush; Rezvani Naraghi, Roxana; Sukhov, Sergey V.; Joannopoulos, John D.; Fink, Yoel; Dogariu, Aristide; Abouraddy, Ayman F.

    2016-01-01

    Scattering of light from dielectric particles whose size is on the order of an optical wavelength underlies a plethora of visual phenomena in nature and is a foundation for optical coatings and paints. Tailoring the internal nanoscale geometry of such “photonic particles” allows tuning their optical scattering characteristics beyond those afforded by their constitutive materials—however, flexible yet scalable processing approaches to produce such particles are lacking. Here, we show that a thermally induced in-fiber fluid instability permits the “digital design” of multimaterial photonic particles: the precise allocation of high refractive-index contrast materials at independently addressable radial and azimuthal coordinates within its 3D architecture. Exploiting this unique capability in all-dielectric systems, we tune the scattering cross-section of equisized particles via radial structuring and induce polarization-sensitive scattering from spherical particles with broken internal rotational symmetry. The scalability of this fabrication strategy promises a generation of optical coatings in which sophisticated functionality is realized at the level of the individual particles. PMID:27274070

  3. Transceiver and system design for digital communications

    Bullock, Scott R

    2017-01-01

    This applied engineering reference covers a wide range of wireless communication design techniques; including link budgets, error detection and correction, adaptive and cognitive techniques, and system analysis of receivers and transmitters.

  4. 1st international conference on digital enterprise design and management

    Krob, Daniel; Rowe, Frantz

    2013-01-01

    This book contains all refereed papers that were accepted to the first edition of the « Digital Enterprise Design & Management » (DED&M 2013) international conference that took place in Paris (France) from February 12 to February 13, 2013. (Website: http://www.dedm2013.dedm.fr/) These proceedings cover the most recent trends in the emerging field of Digital Enterprise, both from an academic and a professional perspective. A special focus is put on digital uses, digital strategies, digital infrastructures and digital governance from an Enterprise Architecture point of view. The DED&M 2013 conference is organized under the guidance of the CESAMES non profit organization (http://www.cesames.net/). and benefits from the support of the "Innovation and Regulation of Digital Services" Chair (Orange, Ecole Polytechnique and Telecom ParisTech) and of the "Complex Systems Engineering" Chair (Dassault Aviation - DCNS - DGA - Thales - Ecole Polytechnique - ENSTA ParisTech – Telecom ParisTech).

  5. Design of 2-D rational digital filters

    Harris, D.B

    1981-01-01

    A novel 2-D rational filter design technique is presented which makes use of a reflection coefficient function (RCF) representation for the filter transfer function. The design problem is formulated in the frequency domain. A least-square error criterion is used though the usual error measure is augmented with barrier functions. These act to restrict the domain of approximation to the set of stable filters. Construction of suitable barrier functions is facilitated by the RCF characterization

  6. Hardware synthesis from DDL. [Digital Design Language for computer aided design and test of LSI

    Shah, A. M.; Shiva, S. G.

    1981-01-01

    The details of the digital systems can be conveniently input into the design automation system by means of Hardware Description Languages (HDL). The Computer Aided Design and Test (CADAT) system at NASA MSFC is used for the LSI design. The Digital Design Language (DDL) has been selected as HDL for the CADAT System. DDL translator output can be used for the hardware implementation of the digital design. This paper addresses problems of selecting the standard cells from the CADAT standard cell library to realize the logic implied by the DDL description of the system.

  7. Analog Design for Digital Deployment of a Serious Leadership Game

    Maxwell, Nicholas; Lang, Tristan; Herman, Jeffrey L.; Phares, Richard

    2012-01-01

    This paper presents the design, development, and user testing of a leadership development simulation. The authors share lessons learned from using a design process for a board game to allow for quick and inexpensive revision cycles during the development of a serious leadership development game. The goal of this leadership simulation is to accelerate the development of leadership capacity in high-potential mid-level managers (GS-15 level) in a federal government agency. Simulation design included a mixed-method needs analysis, using both quantitative and qualitative approaches to determine organizational leadership needs. Eight design iterations were conducted, including three user testing phases. Three re-design iterations followed initial development, enabling game testing as part of comprehensive instructional events. Subsequent design, development and testing processes targeted digital application to a computer- and tablet-based environment. Recommendations include pros and cons of development and learner testing of an initial analog simulation prior to full digital simulation development.

  8. Verilog HDL digital design and modeling

    Cavanagh, Joseph

    2007-01-01

    PREFACE INTRODUCTION History of HDL Verilog HDL IEEE Standard Features Assertion Levels OVERVIEW Design Methodologies Modulo-16 Synchronous Counter Four-Bit Ripple Adder Modules and Ports Designing a Test Bench for Simulation Construct Definitions Introduction to Dataflow Modeling Two-Input Exclusive-OR Gate Four 2-Input AND Gates With Delay Introduction to Behavioral Modeling Three-Input OR Gate Four-Bit Adder Modulo-16 Synchronous Counter Introduction to Structural Modeling Sum-of-Products Implementation Full Adder Four-Bit Ripple Adder Introduction to Mixed-Design Modeling Full Adder Problems LANGUAGE ELEMENTS Comments Identifiers Keywords Bidirectional Gates Charge Storage Strengths CMOS Gates Combinational Logic Gates Continuous Assignment Data Types Module Declaration MOS Switches Multiple-Way Branching Named Ev...

  9. Benchmarking in digital circuit design automation

    Jozwiak, L.; Gawlowski, D.M.; Slusarczyk, A.S.

    2008-01-01

    This paper focuses on benchmarking, which is the main experimental approach to the design method and EDA-tool analysis, characterization and evaluation. We discuss the importance and difficulties of benchmarking, as well as the recent research effort related to it. To resolve several serious

  10. Transceiver and system design for digital communications

    Bullock, Scott R

    2014-01-01

    This is the fourth edition of this successful professional reference book on transceiver design, the device that both sends and receives signals, and its place within the wireless communication system. It gives engineers and others a good intuitive understanding of wireless systems and spread spectrum. New topics covered include cognitive radio, systems, networks, and commercial communications. In addition, many items have been extensively updated to improve the flow of the book and enhance comprehension.

  11. Direct observation of two proton radioactivity using digital photography

    Rykaczewski, Krzysztof Piotr; Pfutzner, M.; Dominik, Wojciech; Janas, Z.; Miernik, K.; Bingham, C.R.; Czyrkowski, HenryK.; Cwiok, Mikolaj; Darby, Iain; Dabrowski, Ryszard; Ginter, T. N.; Grzywacz, Robert Kazimierz; Karny, M.; Korgul, A.; Kusmierz, Waldemar; Liddick, Sean; Rajabali, Mustafa; Stolz, A.

    2007-01-01

    Recently the observation of a new type of spontaneous radioactive decay has been claimed in which two protons are simultaneously ejected by an atomic nucleus from the ground state1,2,3. Experimental data obtained for the extremely neutron-deficient nuclei 45Fe and 54Zn, were interpreted as the first evidence of such a decay mode which has been sought since 1960.4 However, the technique applied in those studies allowed only measurements of the decay time and the total energy released. Particles emitted in the decay were not identified and the conclusions had to be supported by theoretical arguments. Here we show for the first time, directly and unambiguously, that 45Fe indeed disintegrates by two-proton decay. Furthermore, we demonstrate that the decay branch of this isotope leads to various particle emission channels including two-proton and three-proton emission. To achieve this result we have developed a new type of detector V the Optical Time Projection Chamber (OTPC) in which digital photography is applied to nuclear physics for the first time. The detector records images of tracks from charged particles, allowing for their unambiguous identification and the reconstruction of decay events in three dimensions. This new and simple technique provides a powerful method to identify exotic decay channels involving emission of charged particles. It is expected that further studies with the OTPC device will yield important information on nuclei located at and beyond the proton drip-line, thus providing new material for testing and improving models of very unstable atomic nuclei

  12. Low cost digital wind speed meter with wind direction using PIC16F877A

    Sujod, M.Z.; Ismail, M.M. [Malaysia Pahang Univ., Pahang (Malaysia). Faculty of Electrical and Electronics Engineering

    2008-07-01

    Weather measurement tools are necessary to determine the actual weather and forecasting. Wind is one of the weather elements that can be measured using an anemometer which is a device for measuring the velocity or the pressure of the wind. It is one of the instruments used in weather stations. This paper described a circuit design for speed and direction of the meter and created a suitable programming to measure and display the wind speed meter and direction. A microcontroller (PIC16F877A) was employed as the central processing unit for digital wind speed and direction meter. The paper presented and discussed the hardware and software implementation as well as the calibration and results. The paper also discussed cost estimation and future recommendations. It was concluded that the hardware and software implementation were carefully selected after considering the development cost where the cost was much lower than the market prices. 4 refs., 8 figs.

  13. 2nd International Conference on Digital Enterprise Design and Management

    Krob, Daniel; Lonjon, Antoine; Panetto, Hervé

    2014-01-01

    This book contains all refereed papers that were accepted to the second edition of the « Digital Enterprise Design & Management » (DED&M 2014) international conference that took place in Paris (France) from February 4 to February 5, 2014 . These proceedings cover the most recent trends in the emerging field of Digital Enterprise, both from an academic and a professional perspective. A special focus is put on digital uses, digital strategies, digital infrastructures and digital governance from an Enterprise Architecture point of view. The DED&M 2014 conference is organized under the guidance of the Center of Excellence on Systems Architecture, Management, Economy and Strategy  and benefits from the supports of both the Orange – Ecole Polytechnique – Télécom ParisTech “Innovation and Regulation” Chair and the Dassault Aviation – DCNS – DGA – Thales – Ecole Polytechnique – ENSTA ParisTech – Télécom ParisTech  “Complex Systems Engineering” Chair.  .

  14. Design Principles for Digital Badges Used in Libraries

    Rimland, Emily; Raish, Victoria

    2017-01-01

    Digital badges give libraries greater flexibility in delivering impactful instruction to students. They serve as flexible, stackable microcredentials that sequence an information literacy experience across the curriculum. Design considerations rooted in learning theory have a foundation through which to drive decisions. Information literacy badges…

  15. Usability Studies and User-Centered Design in Digital Libraries

    Comeaux, David J.

    2008-01-01

    Digital libraries continue to flourish. At the same time, the principles of user-centered design and the practice of usability testing have been growing in popularity, spreading their influence into the library sphere. This article explores the confluence of these two trends by surveying the current literature on usability studies of digital…

  16. Lab at Home: Hardware Kits for a Digital Design Lab

    Oliver, J. P.; Haim, F.

    2009-01-01

    An innovative laboratory methodology for an introductory digital design course is presented. Instead of having traditional lab experiences, where students have to come to school classrooms, a "lab at home" concept is proposed. Students perform real experiments in their own homes, using hardware kits specially developed for this purpose. They…

  17. Designing Digital Problem Based Learning Tasks that Motivate Students

    van Loon, Anne-Marieke; Ros, Anje; Martens, Rob

    2013-01-01

    This study examines whether teachers are able to apply the principles of autonomy support and structure support in designing digital problem based learning (PBL) tasks. We examine whether these tasks are more autonomy- and structure-supportive and whether primary and secondary school students experience greater autonomy, competence, and motivation…

  18. Design Creativity: Future Directions for Integrated Visualisation

    Jack Steven Goulding

    2015-11-01

    Full Text Available The Architecture, Engineering and Construction (AEC sectors are facing unprecedented challenges, not just with increased complexity of projects per se, but design-related integration. This requires stakeholders to radically re-think their existing business models (and thinking that underpins them, but also the technological challenges and skills required to deliver these projects. Whilst opponents will no doubt cite that this is nothing new as the sector as a whole has always had to respond to change; the counter to this is that design ‘creativity’ is now much more dependent on integration from day one. Given this, collaborative processes embedded in Building Information Modelling (BIM models have been proffered as a panacea solution to embrace this change and deliver streamlined integration. The veracity of design teams’ “project data” is increasingly becoming paramount - not only for the coordination of design, processes, engineering services, fabrication, construction, and maintenance; but more importantly, facilitate ‘true’ project integration and interchange – the actualisation of which will require firm consensus and commitment. This Special Issue envisions some of these issues, challenges and opportunities (from a future landscape perspective, by highlighting a raft of concomitant factors, which include: technological challenges, design visualisation and integration, future digital tools, new and anticipated operating environments, and training requirements needed to deliver these aspirations. A fundamental part of this Special Issue’s ‘call’ was to capture best practice in order to demonstrate how design, visualisation and delivery processes (and technologies affect the finished product viz: design outcome, design procedures, production methodologies and construction implementation. In this respect, the use of virtual environments are now particularly effective at supporting the design and delivery processes. In

  19. Contribution to the study of integrated system design in digital imaging. Application to digital radiology

    Boy, M.

    1987-02-01

    In the first part of this work, we describe the hardware and software used to design integrated systems able to acquire, memorize, process and visualize 1024 x 1024 x 8 bits images. In the second part, we present and analyse the first realised prototype system which is a digital radiology one. After a technical and economical digital radiology study, we present the angiographic and tomographic results. In the third part, we indicate possible evolution of this system and we show how the adopted structure and developed hardware allow applications in various fields [fr

  20. The Digital Design Process - Reflections on a Single Design Case

    Achten, H.H.; Joosen, G.; Dokonal, W.; Hirschberg, U.

    2003-01-01

    CAD tools are increasing their expressive and geometric power to enable a design process in which the computer model can be used throughout the whole design process for realizing the design. Such a process, in which other media such as physical scale models or drawings are no longer required by

  1. The Photoshop Smile Design technique (part 1): digital dental photography.

    McLaren, Edward A; Garber, David A; Figueira, Johan

    2013-01-01

    The proliferation of digital photography and imaging devices is enhancing clinicians' ability to visually document patients' intraoral conditions. By understanding the elements of esthetics and learning how to incorporate technology applications into clinical dentistry, clinicians can predictably plan smile design and communicate anticipated results to patients and ceramists alike. This article discusses camera, lens, and flash selection and setup, and how to execute specific types of images using the Adobe Photoshop Smile Design (PSD) technique.

  2. Design of the digitizing beam position limit detector

    Merl, R.

    1998-01-01

    The Digitizing Beam Position Limit Detector (DBPLD) is designed to identify and react to beam missteering conditions in the Advanced Photon Source (APS) storage ring. The high power of the insertion devices requires these missteering conditions to result in a beam abort in less than 2 milliseconds. Commercially available beam position monitors provide a voltage proportional to beam position immediately upstream and downstream of insertion devices. The DBPLD is a custom VME board that digitizes these voltages and interrupts the heartbeat of the APS machine protection system when the beam position exceeds its trip limits

  3. Design of digital logic control for accelerator magnet power supply

    Long Fengli; Hu Wei; Cheng Jian

    2008-01-01

    For the accelerator magnet power supply, usually the Programmable Logic Controller (PLC) is used to server as the controller for logic protection and control. Along with the development of modern accelerator technology, it is a trend to use fully-digital control to the magnet power supply. It is possible to integrate the logic control part into the digital control component of the power supply, for example, the Field Programmable Gate Array (FPGA). The paper introduces to different methods which are designed for the logic protection and control for accelerator magnet power supplies with the FPGA as the control component. (authors)

  4. Refining teacher design capacity: mathematics teachers' interactions with digital curriculum resources

    Pepin, B.; Gueudet, G.; Trouche, L.

    2017-01-01

    The goal of this conceptual paper is to develop enhanced understandings of mathematics teacher design and design capacity when interacting with digital curriculum resources. We argue that digital resources in particular offer incentives and increasing opportunities for mathematics teachers’ design,

  5. Digital system design and application with VHDL and FPGA

    Lee, Gang; Jo, Yun Seok

    2002-09-15

    Contents of this book are digital system design modeling using VHDL like VHDL basics, writing VHDL for synthesis and VHDL environments, combinational logic design such as 4bit full adder and parallel combinational BCD multiplier sequential logic design, including Johnson counter, stop-watch, Dice game, traffic light controller, elevator controller and alarm clock, complex applications design like dynamic input/output circuit, PS/2 keyboard, LCD, VGA and UART. It also has a supplement about free license for ModelSim and Guide for 3100 X board user.

  6. Digital system design and application with VHDL and FPGA

    Lee, Gang; Jo, Yun Seok

    2002-09-01

    Contents of this book are digital system design modeling using VHDL like VHDL basics, writing VHDL for synthesis and VHDL environments, combinational logic design such as 4bit full adder and parallel combinational BCD multiplier sequential logic design, including Johnson counter, stop-watch, Dice game, traffic light controller, elevator controller and alarm clock, complex applications design like dynamic input/output circuit, PS/2 keyboard, LCD, VGA and UART. It also has a supplement about free license for ModelSim and Guide for 3100 X board user.

  7. Comparison of Designer's Design Thinking Modes in Digital and Traditional Sketches

    Wu, Jun-Chieh; Chen, Cheng-Chi; Chen, Hsin-Chia

    2012-01-01

    The internal design thinking behaviour of designers in the concept development has been an important issue of cognitive psychology. In this study, the design thinking process designers have in applying digital media and traditional paper in the early concept development stage was explored. Special focus was made on the structure and procedure of…

  8. Digital Processing for Modifying and Rearranging Rectilinear and Section Scan Data under Direct Observation

    Kuhl, D. E.; Edwards, R. Q. [University of Pennsylvania, Philadelphia, PA (United States)

    1969-01-15

    Our digital processor for scan data is an on-site instrument that is intermediate in complexity between conventional optical processing devices and large digital computers. It is designed to provide for a wide and flexible range of secondary data operations, direct picture display on a CRT screen, and full operator control of both processing and display operations at the time of viewing. The instrument does not require the user to learn complicated programing schemes. The operator is expected to be a physician who will control the parameters of interest by punching preset buttons on a keyboard while observing changes displayed on a CRT screen. The system functions primarily as an investigative tool for studying perception of scan information and ways of making this information more meaningful. Data operations include data bounding, spatial averaging, iso-count line generation, image addition and subtraction, and several forms of quantitative read-out for analysis of regional data. The instrument is intended to serve as a central processor and reader for data from several units. Investigations with this processor have served as a source of information leading to the design of more simple processing devices suitable for wider acceptance. For example, the Mark III rectilinear and transverse section brain scanner that has evolved from this project is expected to be a practical improvement of the brain study method. This instrument is designed especially for rapid brain scanning using {sup 99m}Tc pertechnetate. It has a self-contained computer, integrated digital circuits for compactness and economy, and provision for transverse section scanning. The advantages of this system are that it provides a more thorough study using both transverse section and rectilinear modes, rapid performance, precise orientation of section and rectilinear views to the patient position, efficient transfer of information between physician and machine during studies, and economy of design

  9. Towards A Framework of Digital Payment Platform Design

    Kazan, Erol; Damsgaard, Jan

    This paper focuses on the triumph march of mobile phones that currently are annexing music players, navigation devices, and cameras as separate physical objects. The next target is set on payment. Through synthesizing available literature, we construct a framework for studying digital payment...... platforms that combines platform, technology and business design aspects. The framework is applied to conduct a comparative case study of digital payment platforms. Four types of market actors are considered: banks, mobile network operators, merchants, and startups, which are incumbents and disrupters....... By hosting third-party services, payment instruments are evolving from single-purpose to multi-functional ones. Our research extends existing payment literature from the MSP perspective to emphasize certain digital payment platform components, which impact strategies and complementary products....

  10. 4 Channel Slave Direct-Digital-Synthesizer – SDDS (EDA-00992)

    BLAS, A; DELONG, J

    2011-01-01

    A novel rf beam control architecture has been successfully tested in the LEIR synchrotron. The design is based on a VME 64X carrier board, including a DSP (digital signal processor), into which different daughter cards can be plugged in. The SDDS (Slave Direct Digital Synthesizer) is one of them. Hardware wise it has the features of a four-channel DAC (digital-to-analogue converter) which inputs are driven by a powerful FPGA (field programmable logic array); the latter is connected to the DSP on the carrier board via high-speed connectors. Mainly, this unit will supply the rf signals driving the cavities at a specified harmonic of the revolution. The main sampling clock feeding the mezzanine board is at a high harmonic of the particle’s revolution frequency. In the PSB, this frequency is varying along the accelerating cycle and this choice allows creating the rf signal feeding the accelerating cavities without changing any parameter along the cycle. The sampling clock is tagged at the revolution rate allowi...

  11. A design study investigating augmented reality and photograph annotation in a digitalized grossing workstation

    Joyce A Chow

    2017-01-01

    Full Text Available Context: Within digital pathology, digitalization of the grossing procedure has been relatively underexplored in comparison to digitalization of pathology slides. Aims: Our investigation focuses on the interaction design of an augmented reality gross pathology workstation and refining the interface so that information and visualizations are easily recorded and displayed in a thoughtful view. Settings and Design: The work in this project occurred in two phases: the first phase focused on implementation of an augmented reality grossing workstation prototype while the second phase focused on the implementation of an incremental prototype in parallel with a deeper design study. Subjects and Methods: Our research institute focused on an experimental and “designerly” approach to create a digital gross pathology prototype as opposed to focusing on developing a system for immediate clinical deployment. Statistical Analysis Used: Evaluation has not been limited to user tests and interviews, but rather key insights were uncovered through design methods such as “rapid ethnography” and “conversation with materials”. Results: We developed an augmented reality enhanced digital grossing station prototype to assist pathology technicians in capturing data during examination. The prototype uses a magnetically tracked scalpel to annotate planned cuts and dimensions onto photographs taken of the work surface. This article focuses on the use of qualitative design methods to evaluate and refine the prototype. Our aims were to build on the strengths of the prototype's technology, improve the ergonomics of the digital/physical workstation by considering numerous alternative design directions, and to consider the effects of digitalization on personnel and the pathology diagnostics information flow from a wider perspective. A proposed interface design allows the pathology technician to place images in relation to its orientation, annotate directly on the

  12. A Design Study Investigating Augmented Reality and Photograph Annotation in a Digitalized Grossing Workstation.

    Chow, Joyce A; Törnros, Martin E; Waltersson, Marie; Richard, Helen; Kusoffsky, Madeleine; Lundström, Claes F; Kurti, Arianit

    2017-01-01

    Within digital pathology, digitalization of the grossing procedure has been relatively underexplored in comparison to digitalization of pathology slides. Our investigation focuses on the interaction design of an augmented reality gross pathology workstation and refining the interface so that information and visualizations are easily recorded and displayed in a thoughtful view. The work in this project occurred in two phases: the first phase focused on implementation of an augmented reality grossing workstation prototype while the second phase focused on the implementation of an incremental prototype in parallel with a deeper design study. Our research institute focused on an experimental and "designerly" approach to create a digital gross pathology prototype as opposed to focusing on developing a system for immediate clinical deployment. Evaluation has not been limited to user tests and interviews, but rather key insights were uncovered through design methods such as " rapid ethnography " and " conversation with materials ". We developed an augmented reality enhanced digital grossing station prototype to assist pathology technicians in capturing data during examination. The prototype uses a magnetically tracked scalpel to annotate planned cuts and dimensions onto photographs taken of the work surface. This article focuses on the use of qualitative design methods to evaluate and refine the prototype. Our aims were to build on the strengths of the prototype's technology, improve the ergonomics of the digital/physical workstation by considering numerous alternative design directions, and to consider the effects of digitalization on personnel and the pathology diagnostics information flow from a wider perspective. A proposed interface design allows the pathology technician to place images in relation to its orientation, annotate directly on the image, and create linked information. The augmented reality magnetically tracked scalpel reduces tool switching though

  13. Future directions in boiling water reactor design

    Wilkins, D.R.; Hucik, S.A.; Duncan, J.D.; Sweeney, J.I.

    1987-01-01

    The Advanced Boiling Water Reactor (ABWR) is being developed by an international team of BWR manufacturers to respond to worldwide utility needs in the 1990's. Major objectives of the ABWR program are design simplification; improved safety and reliability; reduced construction, fuel and operating costs; improved maneuver-ability; and reduced occupational exposure and radwaste. The ABWR incorporates the best proven features from BWR designs in Europe, Japan and the United States and application of leading edge technology. Key features of the ABWR are internal recirculation pumps; fine-motion, electrohydraulic control rod drives; digital control and instrumentation; multiplexed, fiber optic cabling netwoek; pressure suppression containment with horizontal vents; cylindrical reinforced concrete containment; structural integration of the containment and reactor building; severe accident capability; state-of-the-art fuel; advanced trubine/generator with 52'' last stage buckets; and advanced radwaste technology. The ABWR is ready for lead plant application in Japan, where it is being developed as the next generation Japan standard BWR under the guidance and leadership of The Tokyo Electric Power Company, Inc. and a group of Japanese BWR utilities. In the United States it is being adapted to the needs of US utilities through the Electric Power Research Institute's Advanced LWR Requirements Program, and is being reviewed by the US Nuclear Regulatory Commission for certification as a preapproved US standard BWR under the US Department of Energy's ALWR Design Verification Program. These cooperative Japanese and US programs are expected to establish the ABWR as a world class BWR for the 1990's...... (author)

  14. Direct fuel cell product design improvement

    Maru, H.C.; Farooque, M. [Energy Research Corp., Danbury, CT (United States)

    1996-12-31

    Significant milestones have been attained towards the technology development field testing and commercialization of direct fuel cell power plant since the 1994 Fuel Cell Seminar. Under a 5-year cooperative agreement with the Department of Energy signed in December 1994, Energy Research Corporation (ERC) has been developing the design for a MW-scale direct fuel cell power plant with input from previous technology efforts and the Santa Clara Demonstration Project. The effort encompasses product definition in consultation with the Fuel Cell Commercialization Group, potential customers, as well as extensive system design and packaging. Manufacturing process improvements, test facility construction, cell component scale up, performance and endurance improvements, stack engineering, and critical balance-of-plant development are also addressed. Major emphasis of this product design improvement project is on increased efficiency, compactness and cost reduction to establish a competitive place in the market. A 2.85 MW power plant with an efficiency of 58% and a footprint of 420 m{sup 2} has been designed. Component and subsystem testing is being conducted at various levels. Planning and preparation for verification of a full size prototype unit are in progress. This paper presents the results obtained since the last fuel cell seminar.

  15. Efficient Parameter Searches for Colloidal Materials Design with Digital Alchemy

    Dodd, Paul, M.; Geng, Yina; van Anders, Greg; Glotzer, Sharon C.

    Optimal colloidal materials design is challenging, even for high-throughput or genomic approaches, because the design space provided by modern colloid synthesis techniques can easily have dozens of dimensions. In this talk we present the methodology of an inverse approach we term ''digital alchemy'' to perform rapid searches of design-paramenter spaces with up to 188 dimensions that yield thermodynamically optimal colloid parameters for target crystal structures with up to 20 particles in a unit cell. The method relies only on fundamental principles of statistical mechanics and Metropolis Monte Carlo techniques, and yields particle attribute tolerances via analogues of familiar stress-strain relationships.

  16. Design Principles for the Information Architecture of a SMET Education Digital Library.

    Dong, Andy; Agogino, Alice M.

    This implementation paper introduces principles for the information architecture of an educational digital library, principles that address the distinction between designing digital libraries for education and designing digital libraries for information retrieval in general. Design is a key element of any successful product. Good designers and…

  17. In search of design principles for developing digital learning & performance support for a student design task

    Bollen, Lars; van der Meij, Hans; Leemkuil, Hendrik H.; McKenney, Susan

    2015-01-01

    A digital learning and performance support environment for university student design tasks was developed. This paper describes on the design rationale, process, and the usage results to arrive at a core set of design principles for the construction of such an environment. We present a collection of

  18. In search of design principles for developing digital learning & performance support for a student design task

    Bollen, Lars; Van der Meij, Hans; Leemkuil, Henny; McKenney, Susan

    2016-01-01

    A digital learning and performance support environment for university student design tasks was developed. This paper describes on the design rationale, process, and the usage results to arrive at a core set of design principles for the construction of such an environment. We present a collection of

  19. Artificial intelligence and design: Opportunities, research problems and directions

    Amarel, Saul

    1990-01-01

    that are of intrinsic concern to AI. We present examples of current AI work on specific design tasks, and discuss new directions of research, both as extensions of current work and in the context of new design tasks where domain knowledge is either intractable or incomplete. The domains discussed include Digital Circuit Design, Mechanical Design of Rotational Transmissions, Design of Computer Architectures, Marine Design, Aircraft Design, and Design of Chemical Processes and Materials. Work in these domains is significant on technical grounds, and it is also important for economic and policy reasons.

  20. Computer-aided design and manufacture of hyrax devices: Can we really go digital?

    Graf, Simon; Cornelis, Marie A; Hauber Gameiro, Gustavo; Cattaneo, Paolo M

    2017-12-01

    The aim of this pilot study was to illustrate the feasibility of a new digital procedure to fabricate metallic orthodontic appliances. Hyrax appliances for rapid palatal expansion were produced for 3 patients using a CAD/CAM procedure without physical impressions or printed models. The work flow consisted of intraoral scanning, digital design with incorporation of a scanned prefabricated expansion screw, direct 3-dimensional metal printing via laser melting, welding of an expansion screw, insertion, and finally activation in the patients' mouths. Finite element analyses of the actual hyrax appliances were performed to ensure that the printable material used in combination with the chosen design would withstand the stress generated during activation. The results of these analyses were positive. The clinical results showed that this procedure is an efficient and viable digital way for constructing metallic orthodontic appliances. The flexibility of the digital appliance design, together with the biocompatibility and strength of the chosen material, offers a huge potential for more advanced appliance design. Copyright © 2017 American Association of Orthodontists. Published by Elsevier Inc. All rights reserved.

  1. Direct calibration of PICKY-designed microarrays

    Ronald Pamela C

    2009-10-01

    Full Text Available Abstract Background Few microarrays have been quantitatively calibrated to identify optimal hybridization conditions because it is difficult to precisely determine the hybridization characteristics of a microarray using biologically variable cDNA samples. Results Using synthesized samples with known concentrations of specific oligonucleotides, a series of microarray experiments was conducted to evaluate microarrays designed by PICKY, an oligo microarray design software tool, and to test a direct microarray calibration method based on the PICKY-predicted, thermodynamically closest nontarget information. The complete set of microarray experiment results is archived in the GEO database with series accession number GSE14717. Additional data files and Perl programs described in this paper can be obtained from the website http://www.complex.iastate.edu under the PICKY Download area. Conclusion PICKY-designed microarray probes are highly reliable over a wide range of hybridization temperatures and sample concentrations. The microarray calibration method reported here allows researchers to experimentally optimize their hybridization conditions. Because this method is straightforward, uses existing microarrays and relatively inexpensive synthesized samples, it can be used by any lab that uses microarrays designed by PICKY. In addition, other microarrays can be reanalyzed by PICKY to obtain the thermodynamically closest nontarget information for calibration.

  2. All-Pole Recursive Digital Filters Design Based on Ultraspherical Polynomials

    N. Stojanovic

    2014-09-01

    Full Text Available A simple method for approximation of all-pole recursive digital filters, directly in digital domain, is described. Transfer function of these filters, referred to as Ultraspherical filters, is controlled by order of the Ultraspherical polynomial, nu. Parameter nu, restricted to be a nonnegative real number (nu ≥ 0, controls ripple peaks in the passband of the magnitude response and enables a trade-off between the passband loss and the group delay response of the resulting filter. Chebyshev filters of the first and of the second kind, and also Legendre and Butterworth filters are shown to be special cases of these allpole recursive digital filters. Closed form equations for the computation of the filter coefficients are provided. The design technique is illustrated with examples.

  3. Extend Course for Product Designer in Digital Mobile Era

    CHAO, Fang-Lin; LIU, Tzu-Heng; HUANG, Xian-Chun

    2017-12-01

    Product design refers to a system of processes from confirming a product’s specifications to product’s structure. Form, technology, and needs must be considered simultaneously to ensure qualities. In recent years, with the advancement of smartphone technology, many products are connected with apps. Designers cannot exclude themselves from this new wave of the trend. In this article, household hydroponic products design is used as an example, to show the close relationship between digital mobile technology and product design in the contemporary world. Regularly measure the amount of liquid to be added is difficult for a consumer who has no professional experience. To facilitate the introduction of small-scale aquaculture systems into the home, we proposed sensor hardware combined with App software, measured EC and pH value and transmitted to the phone. The app can calculate and display the amount of added and control the amount of inserted through a Bluetooth connection. The physical design needs to take into account the connection between the electronic parts and the circuit board, and interface operation. Thus, not only the model of the product but also the user interface has to be integrated to show the product's quality completely. Besides, authors made reflection upon the necessity for adjustments for interdisciplinary courses under the changing digital mobile era. Also, under the current curriculum structure, possible teaching approach is expressed for extending student’s feasibility.

  4. Examining the Characteristics of Digital Learning Games Designed by In-Service Teachers

    An, Yun-Jo; Cao, Li

    2017-01-01

    In order to better understand teachers' perspectives on the design and development of digital game-based learning environments, this study examined the characteristics of digital learning games designed by teachers. In addition, this study explored how game design and peer critique activities influenced their perceptions of digital game-based…

  5. Digital maker-entrepreneurs in open design: What activities make up their business model?

    Dr. P. Troxler; Patricia Wolf

    2017-01-01

    The business models of digital maker-entrepreneurs in open design are inextricably linked to the broader open design community. Digital makers share designs on online platforms such as Thingiverse and use digital manufacturing technology such as 3-D printing as a generative mechanism for their

  6. Design and Usability of Digital Libraries: Case Studies in the Asia Pacific

    Theng, Yin-Leng, Ed.; Foo, Schubert, Ed.

    2005-01-01

    This book showcases some of the best digital library practices from organizations in the Asia Pacific. Particular emphasis has been placed on the design, use and usability of digital libraries. Not only are digital libraries examined, but related technologies, the management of knowledge in digital libraries, and the associated usability and…

  7. Design and application of finite impulse response digital filters

    Miller, T.R.; Sampathkumaran, K.S.

    1982-01-01

    The finite impulse response (FIR) digital filter is a spatial domain filter with a frequency domain representation. The theory of the FIR filter is presented and techniques are described for designing FIR filters with known frequency response characteristics. Rational design principles are emphasized based on characterization of the imaging system using the modulation transfer function and physical properties of the imaged objects. Bandpass, Wiener, and low-pass filters were designed and applied to 201 Tl myocardial images. The bandpass filter eliminates low-frequency image components that represent background activity and high-frequency components due to noise. The Wiener, or minimum mean square error filter 'sharpens' the image while also reducing noise. The Wiener filter illustrates the power of the FIR technique to design filters with any desired frequency reponse. The low-pass filter, while of relative limited use, is presented to compare it with a popular elementary 'smoothing' filter. (orig.)

  8. An Analytic Creativity Assessment Scale for Digital Game Story Design: Construct Validity, Internal Consistency and Interrater Reliability

    Chuang, Tsung-Yen; Huang, Yun-Hsuan

    2015-01-01

    Mobile technology has rapidly made digital games a popular entertainment to this digital generation, and thus digital game design received considerable attention in both the game industry and design education. Digital game design involves diverse dimensions in which digital game story design (DGSD) particularly attracts our interest, as the…

  9. Design rules for superconducting analog-digital transducers; Entwurfsregeln fuer Supraleitende Analog-Digital-Wandler

    Haddad, Taghrid

    2015-05-29

    This Thesis is a contribution for dimensioning aspects of circuits designs in superconductor electronics. Mainly superconductor comparators inclusive Josephson comparators as well as QOJS-Comparators are investigated. Both types were investigated in terms of speed and sensitivity. The influence of the thermal noise on the decision process of the comparators represent in so called gray zone, which is analysed in this thesis. Thereby, different relations between design parameters were derived. A circuit model of the Josephson comparator was verified by experiments. Concepts of superconductor analog-to-digital converters, which are based on above called comparators, were investigated in detail. From the comparator design rules, new rules for AD-converters were derived. Because of the reduced switching energy, the signal to noise ratio (SNR) of the circuits is affected and therefore the reliability of the decision-process is affected. For special applications with very demanding requirements in terms of the speed and accuracy superconductor analog-to-digital converters offer an excellent performance. This thesis provides relations between different design paramenters and shows resulting trade-offs, This method is transparent and easy to transfer to other circuit topologies. As a main result, a highly predictive tool for dimensioning of superconducting ADC's is proved.

  10. Design rules for superconducting analog-digital transducers

    Haddad, Taghrid

    2015-01-01

    This Thesis is a contribution for dimensioning aspects of circuits designs in superconductor electronics. Mainly superconductor comparators inclusive Josephson comparators as well as QOJS-Comparators are investigated. Both types were investigated in terms of speed and sensitivity. The influence of the thermal noise on the decision process of the comparators represent in so called gray zone, which is analysed in this thesis. Thereby, different relations between design parameters were derived. A circuit model of the Josephson comparator was verified by experiments. Concepts of superconductor analog-to-digital converters, which are based on above called comparators, were investigated in detail. From the comparator design rules, new rules for AD-converters were derived. Because of the reduced switching energy, the signal to noise ratio (SNR) of the circuits is affected and therefore the reliability of the decision-process is affected. For special applications with very demanding requirements in terms of the speed and accuracy superconductor analog-to-digital converters offer an excellent performance. This thesis provides relations between different design paramenters and shows resulting trade-offs, This method is transparent and easy to transfer to other circuit topologies. As a main result, a highly predictive tool for dimensioning of superconducting ADC's is proved.

  11. Evaluation of the fit of zirconia copings fabricated by direct and indirect digital impression procedures.

    Lee, Bora; Oh, Kyung Chul; Haam, Daewon; Lee, Joon-Hee; Moon, Hong-Seok

    2018-02-07

    Intraoral scanners are effective for direct digital impression when dental restorations are fabricated using computer-aided design and computer-aided manufacturing (CAD-CAM); however, if the abutment tooth cannot be dried completely or the prepared margin is placed subgingivally, accurate digital images cannot always be guaranteed. The purpose of this in vitro study was to compare the internal and marginal discrepancies of zirconia copings fabricated directly using an intraoral scanner with those fabricated indirectly with impression scanning. Forty-five resin dies fabricated with a 3-dimensional (3D) printer were divided into 3 groups: direct scanning (DS), impression scanning (IMP), and lost-wax casting (LW). For the DS group, a resin die was scanned with an intraoral scanner (Trios; 3Shape), whereas for the IMP group, impressions made with polyether were scanned with a cast scanner (D700; 3Shape). The zirconia copings were fabricated in the same way in the DS and IMP groups. For the LW group, impressions were made in the same way as in the IMP group, and Ni-Cr alloy copings were fabricated using LW. The marginal and internal discrepancies of the copings were measured by cementing them onto resin dies, embedding them in acrylic resin, and sectioning them in a buccolingual direction. The cement layer was measured, and the Kruskal-Wallis test was used to detect significant differences (α=.05). A nonparametric Friedman test was also performed to compare the measurements of each group by location (α=.05). The mean marginal discrepancies in the DS, IMP, and LW groups were 18.1 ±9.8, 23.2 ±17.2, and 32.3 ±18.6 μm (mean ±standard deviation), respectively. The mean internal discrepancies of the DS, IMP, and LW groups in the axial area were 38.0 ±9.1, 47.0 ±16.3, and 36.5 ±15.8 μm, and those in the occlusal area were 36.7 ±16.9, 33.4 ±21.6, and 44.5 ±31.9 μm, respectively. No statistically significant differences were found in marginal or internal

  12. Simulation of the Direct Digital Synthesis module for Helium RFQ LLRF system

    Jeong, Hae-Seong; Ahn, Tae-Sung; Kim, Seong-Gu; Kwon, Hyeok-Jung; Kim, Han-Sung; Song, Young-Gi; Seol, Kyung-Tae; Cho, Yong-Sub [Korea Atomic Energy Research Institute, Gyeongju (Korea, Republic of)

    2015-10-15

    In this paper, the DDS module in the FPGA simulated and the analysis result will be introduced. Using Xilinx ISE design suite which is tool for developing the FPGA logic module, DDS module simulated. KOMAC (Korea Multi-purpose Accelerator Complex) has a plan to develop the helium irradiation system. This system includes the Ion source, LEBT, RFQ, MEBT systems to transport helium particles to the target. Especially, the RFQ (Radio Frequency Quadrupole) system should receive the 200 MHz RF within 1% amplitude error stability. For supplying stable 200 MHz RF to the RFQ, the LLRF (low-level radio frequency) should be controlled by control system. This helium RFQ LLRF control system have a concept to track the cavity resonance frequency. For tracking the cavity resonance frequency, the FPGA (Field Programmable Gate Array) in the digital board will tune the frequency of the output sinusoidal signal. In order to implement this frequency tracking concept, the DDS (Direct Digital Synthesis) module should be implemented in the FPGA. In the future, frequency tracking system will be tested using test cavity.

  13. A preliminary design of mechanical device on industrial digital radiography equipment design

    Nur Khasan; Samuel Praptoyo

    2015-01-01

    A preliminary design of mechanical device on industrial digital radiography equipment has been done. this design is intended as a basis for the manufacture of complete facilities for the realization a prototype on industrial digital radiography equipment. the design and construction were carried out by paying attention to the general configuration of the basic design in which its mechanical design has several components with specific dimensions and heavy mass. this design consist of a main frame holder, flat panel detector support and hydraulic hand stacker for mounting the x-ray machine. this mechanical device design will then be fabricated to facilitate and assist work of digital radiographic retrieval. computer application programs sketch-up is used to draw this design and the analysis stress of autodesk inventor to analysis the strength construction design. the results of this design are the configuration drawing, sketch drawings of construction and the safety factor of construction design with a minimum value of 2.39 as well as a maximum value of 15 when to be simulated by the load 500 Kg which is 4 times of total workload. (author)

  14. Reconfigurable signal processor designs for advanced digital array radar systems

    Suarez, Hernan; Zhang, Yan (Rockee); Yu, Xining

    2017-05-01

    The new challenges originated from Digital Array Radar (DAR) demands a new generation of reconfigurable backend processor in the system. The new FPGA devices can support much higher speed, more bandwidth and processing capabilities for the need of digital Line Replaceable Unit (LRU). This study focuses on using the latest Altera and Xilinx devices in an adaptive beamforming processor. The field reprogrammable RF devices from Analog Devices are used as analog front end transceivers. Different from other existing Software-Defined Radio transceivers on the market, this processor is designed for distributed adaptive beamforming in a networked environment. The following aspects of the novel radar processor will be presented: (1) A new system-on-chip architecture based on Altera's devices and adaptive processing module, especially for the adaptive beamforming and pulse compression, will be introduced, (2) Successful implementation of generation 2 serial RapidIO data links on FPGA, which supports VITA-49 radio packet format for large distributed DAR processing. (3) Demonstration of the feasibility and capabilities of the processor in a Micro-TCA based, SRIO switching backplane to support multichannel beamforming in real-time. (4) Application of this processor in ongoing radar system development projects, including OU's dual-polarized digital array radar, the planned new cylindrical array radars, and future airborne radars.

  15. Design of Multimedia-based Digital Storybooks for Preschool Education

    Didik Dwi Prasetya

    2018-02-01

    Full Text Available Storytelling is one of the suitable approaches to deliver the right information and build the character education of young children. The story content presented by utilizing multimedia elements is able to offer more attractive and increase interest for children. This paper proposes an ICT approach through multimedia-based digital storybook design with an EPUB reflowable format that can be accessed using various electronic devices, whether desktop, laptop, or mobile. The research subjects are limited to 4-5-year-old preschool children. The research reveals that children were very enthusiastic about storybooks, with or without supports from teachers

  16. Ceramic Prototypes – Design, Computation, and Digital Fabrication

    M. Bechthold

    2016-12-01

    Full Text Available Research in ceramic material systems at Harvard University has introduced a range of novel applications which combine digital manufacturing technologies and robotics with imaginative design and engineering methods. Prototypes showcase the new performative qualities of ceramics and the integration of this material in today’s construction culture. Work ranges from daylight control systems to structural applications and a robotic tile placement system. Emphasis is on integrating novel technologies with tried and true manufacturing methods. The paper describes two distinct studies – one on 3D print-ing of ceramics, the other on structural use of large format thin tiles.

  17. [Design and development of the DSA digital subtraction workstation].

    Peng, Wen-Xian; Peng, Tian-Zhou; Xia, Shun-Ren; Jin, Guang-Bo

    2008-05-01

    According to the patient examination criterion and the demands of all related departments, the DSA digital subtraction workstation has been successfully designed and is introduced in this paper by analyzing the characteristic of video source of DSA which was manufactured by GE Company and has no DICOM standard interface. The workstation includes images-capturing gateway and post-processing software. With the developed workstation, all images from this early DSA equipment are transformed into DICOM format and then are shared in different machines.

  18. The users centered design of a new digital fluorometer

    Farias, Marcos S.; Santos, Isaac J.A.L. dos; Grecco, Claudio H.S.; Pedrosa, Paulo S.; Colthurst, Carlos M.; Szabo, Andre P.

    2009-01-01

    The fluorometer is the equipment used in chemical analysis laboratories, research institutes and nuclear fuel cycle companies. This equipment measures an unknown amount of uranium in ores, rivers, etc. The fluorometer functioning is based on the uranium fluorescence when submitted to the ultraviolet radiation incidence. The fluorescence is measured by an electronic optic system with optics filters, photomultiplier tube, and a current amplifier. The user centered design involves the user in the product development in all phases of the design process. Users are not simply consulted at the beginning of the design process and evaluated the system at the end; they are treated as partners throughout the design process. The user centered design emphasizes the needs and abilities of the users and improves the usability of the equipment. The activity centered design emphasizes the development of the equipment with a deep understanding of the users activities and of the current work practices of the users. The aim of this paper is to present a methodological framework that contributes to the design and evaluation of a new digital fluorometer towards an approach related to the users and their activities. This methodological framework includes users-based testing, interviews, questionnaires, human factors standards and guidelines, the users activity analysis and users satisfaction questionnaire. (author)

  19. Digital technology use in ELT classrooms and self-directed learning

    Nehir Sert; Ebru Boynueğri

    2016-01-01

    The digital era is a new challenge for teachers. While children get acquainted with digital technology before the age of six, teachers, who have encountered the digital world at a later time in their lives, struggle with it. Self-directed learning, which is crucial for lifelong learning, can be enhanced by the use of technology within and beyond classroom settings. The aim of this study was to examine the difference between the perceptions of students in low- and high-income groups about thei...

  20. Drill-string design for directional wells

    Dawson, R; Corbett, K T [Exxon Production Research Co., Houston, TX (USA)

    1983-01-01

    This paper is concerned with predicting the tension and torsion loads on drill strings in directional wells and with adjusting the string design or well plan to provide adequate strength. Drill-string drag is the incremental force that is required to move the pipe up or down in the hole; torque is the moment required to rotate the pipe. Drag forces are usually given relative to the string weight measured with the string roating but not reciprocating. Measured from the roating string weight, the pick-up drag is usually slightly greater than the slack-off drag. The magnitudes of torque and drag are related in any particular well; high drag forced and exessive torque loads normally occur together. There are a number of phenomena wich contribute to torque and drag. Included are tight hole conditions, sloughing hole, keyseats, differential sticking, cuttings build up due to poor hole cleaning and sliding wellbore friction. With the exception of sliding friction, these causes are associated with problem conditions in the wellbore. Conversely, in wells with good hole conditions, the primary source of torque and drag is sliding friction. This paper is only concerned with the torque and drag caused by sliding friction. The cabability to predict frictional loads on drill pipe has two main benefits. First, more complete knowledge of drill-string loading allows use of improved drill-string design techniques. Drill-string components can be chosen using a systematic approach considering the force involved. Second, deep, highly-deviated wells can be planned to minimize torque and drag. Use of torque and drag as a criteria to select the most appropriate well path will help ensure successful drilling operations to total depth. 1 fig., 2 tabs. (Author).

  1. Self-Directed Digital Learning: When Do Dental Students Study?

    Jackson, Tate H; Zhong, James; Phillips, Ceib; Koroluk, Lorne D

    2018-04-01

    The Growth and Development (G&D) curriculum at the University of North Carolina at Chapel Hill School of Dentistry uses self-directed web-based learning modules in the place of lectures and includes scheduled self-study times during the 8 am-5 pm school hours. The aim of this study was to use direct observation to evaluate dental students' access patterns with the self-directed, web-based learning modules in relation to planned self-study time allocated across the curriculum, proximity to course examinations, and course performance. Module access for all 80 students in the DDS Class of 2014 was recorded for date and time across the four G&D courses. Module access data were used to determine likelihood of usage during scheduled time and frequency of usage in three timeframes: >7, 3 to 7, and 0 to 2 days before the final exam. The results showed a statistically significant difference in the likelihood of module access during scheduled time across the curriculum (pstudents, 64% accessed modules at least once during scheduled time in G&D1, but only 10%, 19%, and 18% in G&D2, G&D3, and G&D4, respectively. For all courses, the proportion of module accesses was significantly higher 0-2 days before an exam compared to the other two timeframes. Module access also differed significantly within each timeframe across all four courses (pstudents rarely accessed learning modules during syllabus-budgeted self-study time and accessed modules more frequently as course exams approached.

  2. Clinical evaluation of digital angiographic system equipped with the Safire' flat-panel detector of a direct conversion type

    Miura, Yoshiaki; Miura, Yusuke; Goto, Keiichi

    2003-01-01

    This report presents a report on clinical evaluation of our newly developed flat-panel X-ray detector of a direct conversion type, designed to provide images of a resolution higher than, or at least equal to, that ensured by X-ray photographic films, in clinical digital X-ray cinematography. This new detector was named 'Safire' the acronym of 'Shimadzu advanced flat imaging receptor', emphasizing its high technological level, such as the capability to ensure high quality of images. The clinical evaluation of Shimadzu DIGITEX Premier digital angiography system, equipped with this new flat-panel X-ray detector of a direct conversion type, has been started in March, 2003, at the Kokura Memorial Hospital in Kyushu, Japan. (author)

  3. Erythema-directed digital photography for the enhanced evaluation of topical treatments for acne vulgaris.

    Micali, G; Dall'Oglio, F; Tedeschi, A; Lacarrubba, F

    2018-01-31

    Erythema-directed digital photography is a novel method for evaluating the efficacy and tolerability of topical acne treatments. Here, we describe three case reports in which erythema-directed digital photography was used to evaluate acne before and after up to 12 weeks of treatment with clindamycin 1%/tretinoin 0.025% (Clin-RA). Erythema-directed digital photography was used to evaluate acne in three patients with mild-to-moderate facial acne, two of whom had refused to continue previous topical acne treatment (benzoyl peroxide 5% and clindamycin 1%/benzoyl peroxide 5%) due to persistent irritation. Acne lesions and erythema were evaluated using standard clinical photography and erythema-directed digital photography (VISIA-CR ™ system) before and after 8-12 weeks of treatment with Clin-RA. Erythema-directed digital photography revealed background erythema from previous topical acne treatments that was not evident from standard clinical photographs and allowed a better visualization of both inflammatory and non-inflammatory lesions. In all patients, there was a clear improvement in background erythema and a reduction in acne lesions following treatment with Clin-RA. This study has demonstrated for the first time that erythema-directed digital photography can enhance the evaluation of the efficacy and tolerability of topical acne treatments. These cases show that Clin-RA was associated with improved efficacy and tolerability vs previous treatments with topical monotherapy (benzoyl peroxide 5%) or a topical fixed-dose combination (clindamycin 1%/benzoyl peroxide 5%). © 2018 The Authors. Skin Research and Technology Published by John Wiley & Sons Ltd.

  4. Digitally controlled oscillator design with a variable capacitance XOR gate

    Kumar, Manoj; Arya, Sandeep K.; Pandey, Sujata

    2011-01-01

    A digitally controlled oscillator (DCO) using a three-transistor XOR gate as the variable load has been presented. A delay cell using an inverter and a three-transistor XOR gate as the variable capacitance is also proposed. Three-, five- and seven-stage DCO circuits have been designed using the proposed delay cell. The output frequency is controlled digitally with bits applied to the delay cells. The three-bit DCO shows output frequency and power consumption variation in the range of 3.2486–4.0267 GHz and 0.6121–0.3901 mW, respectively, with a change in the control word 111–000. The five-bit DCO achieves frequency and power of 1.8553–2.3506 GHz and 1.0202–0.6501 mW, respectively, with a change in the control word 11111–00000. Moreover, the seven-bit DCO shows a frequency and power consumption variation of 1.3239–1.6817 GHz and 1.4282–0.9102 mW, respectively, with a varying control word 1111111–0000000. The power consumption and output frequency of the proposed circuits have been compared with earlier reported circuits and the present approaches show significant improvements. (semiconductor integrated circuits)

  5. A direct digital controller for an automatic sodium plugging meter

    Tobias, A.

    1977-07-01

    A plugging meter is a device for monitoring the impurity level of liquid sodium. It is used to measure the temperature at which an impurity precipitates or re-dissolves at a restricting orifice. The concentration of the impurity may be then deduced from known solubility/temperature relationships. A software controller for a sodium plugging meter has been implemented on a PDP-11 using SWEPSPEED. The algorithm used to perform both flow and temperature control functions is based on a modified standard three-term controller. Both design and operation of the controller are described. The functions which may be performed by the controller are: (i) maintain a steady temperature at the restricting orifice, (ii) perform a temperature ramp at a rate defined by the operator, and (iii) maintain a partial plug of impurities at the orifice by appropriate manipulation of the temperature. Accuracies so far achieved are approximately +- 5% for flow control and better that +- 1 0 C for temperature control. (author)

  6. Research on digital system design of nuclear power valve

    Zhang, Xiaolong; Li, Yuan; Wang, Tao; Dai, Ye

    2018-04-01

    With the progress of China's nuclear power industry, nuclear power plant valve products is in a period of rapid development, high performance, low cost, short cycle of design requirements for nuclear power valve is proposed, so there is an urgent need for advanced digital design method and integrated design platform to provide technical support. Especially in the background of the nuclear power plant leakage in Japan, it is more practical to improve the design capability and product performance of the nuclear power valve. The finite element numerical analysis is a common and effective method for the development of nuclear power valves. Nuclear power valve has high safety, complexity of valve chamber and nonlinearity of seal joint surface. Therefore, it is urgent to establish accurate prediction models for earthquake prediction and seal failure to meet engineering accuracy and calculation conditions. In this paper, a general method of finite element modeling for nuclear power valve assembly and key components is presented, aiming at revealing the characteristics and rules of finite element modeling of nuclear power valves, and putting forward aprecision control strategy for finite element models for nuclear power valve characteristics analysis.

  7. Benefits and Factors Influencing the Design of Intergenerational Digital Games: A Systematic Literature Review

    de la Hera Conde-Pumpido, T.; Loos, E.F.; Simons, M.; Blom, J.

    2017-01-01

    The main purpose of this paper is to review the benefits and factors to be taken into consideration for the design of intergenerational digital games. We conducted a systematic in Scopus, Web of Science, PsicInfo, Pubmed and Science Direct, finally including 16 empirical studies written in English.

  8. Digital decoupling and disentangling: towards design for romantic break up

    Herron, D.; Moncur, W.; van den Hoven, E.

    2017-01-01

    Romantic relationships are often facilitated through digital technologies, such as social networking sites and communication services. They are also facilitated through 'digital possessions', such as messages sent to mobile devices and photos shared through social media. When individuals break up,

  9. Design and implementation of a remotely managed digital signage solution

    Regmi, Amrit

    2015-01-01

    Industries and businesses are moving to digital signage from the traditional printed signage as a tool for advertisement and broadcasting information to clients, potential customers, and the public. The availability of affordable flat screen digital displays has enabled the businesses to replace printed signage with digital signage. As a result, digital signage is expected play an important role in delivering information to the public as it can be customized to display timely information to a...

  10. Digital health increasing the impact with personalized design

    Empelen, P. van; Otten, W.; Molema, H.; Keijsers, J.; Mooij, R.

    2016-01-01

    Digital health is considered the ‘holy grail’ of effective and sustainable health(care). It uses the latest technology, apps and data to support and improve health. Digital health tools can benefit both patients and healthy individuals, with support and advice. But healthcare professionals, policymakers and scientist can also benefit from the (big) data and insights collected by digital health applications. A well-known example of digital health is eHealth, which provides information- and com...

  11. Design, Construction and Commissioning of the Digital Hadron Calorimeter - DHCAL

    Adams, C; Bilki, B.; Butler, J.; Corriveau, F.; Cundiff, T.; Drake, G.; Francis, K.; Furst, B.; Guarino, V.; Haberichter, B.; Hazen, E.; Hoff, J.; Holm, S.; Kreps, A.; DeLurgio, P.; Matijas, Z.; Monte, L.Dal; Mucia, N.; Norbeck, E.; Northacker, D.; Onel, Y.; Pollack, B.; Repond, J.; Schlereth, J.; Skrzecz, F.; Smith, J.R.; Trojand, D.; Underwood, D.; Velasco, M.; Walendziak, J.; Wood, K.; Wu, S.; Xia, L.; Zhang, Q.; Zhao, A.

    2016-01-01

    A novel hadron calorimeter is being developed for future lepton colliding beam detectors. The calorimeter is optimized for the application of Particle Flow Algorithms (PFAs) to the measurement of hadronic jets and features a very finely segmented readout with 1 x 1 cm2 cells. The active media of the calorimeter are Resistive Plate Chambers (RPCs) with a digital, i.e. one-bit, readout. To first order the energy of incident particles in this calorimeter is reconstructed as being proportional to the number of pads with a signal over a given threshold. A large-scale prototype calorimeter with approximately 500,000 readout channels has been built and underwent extensive testing in the Fermilab and CERN test beams. This paper reports on the design, construction, and commissioning of this prototype calorimeter.

  12. Design and Implementation of a Digital Angular Rate Sensor

    Zhen Peng

    2010-10-01

    Full Text Available With the aim of detecting the attitude of a rotating carrier, the paper presents a novel, digital angular rate sensor. The sensor consists of micro-sensing elements (gyroscope and accelerometer, signal processing circuit and micro-processor (DSP2812. The sensor has the feature of detecting three angular rates of a rotating carrier at the same time. The key techniques of the sensor, including sensing construction, sensing principles, and signal processing circuit design are presented. The test results show that the sensor can sense rolling, pitch and yaw angular rate at the same time and the measurement error of yaw (or pitch angular rate and rolling rate of the rotating carrier is less than 0.5%.

  13. Encouraging New Encounters: Digital Design Patterns to Support Social Wellbeing

    Mitchell, Robb; Pallaris, Kay

    2018-01-01

    ) and successfully approaching strangers in public places necessitates considerable skills (Mondada, 2009). Computer scientists, interaction designers, new media artists and other inventive practitioners and researchers have undertaken a wide variety of experimentation with digital means to support social......Interpersonal contact can be crucial to subjective wellbeing (Miesen and Schaafsma, 2008) as social isolation can create vicious spirals of self-destructive behaviour that further decreases lonely individuals’ social skills and motivations towards sociability (Caccioppo and Patrick, 2009). Lacking...... social connection has also been argued to have negative impacts on physiological health (ibid). However, developing new interpersonal connections is an elixir that is easy to prescribe but difficult to supply. Initiating a conversation with strangers is difficult for many people (Crozier, 1990...

  14. Design and Implementation of an Embedded Digital Throwing System Based on MEMS Multiaxial Accelerometer

    Zhen GAO

    2010-04-01

    Full Text Available This paper presents a novel embedded digital throwing system for synchronously sensing the throwing force of shot-put athletes in real time. The three axes integrated accelerometer, as a crucial device in the force sensing system, can acquire the kinetics data along three orthogonal directions with reasonably high accuracy. The digital shot with almost the same size and weight as the standard shot for open female has been designed, fabricated and implemented. The mechanical structure, signal processing system, and human-machine interface are illuminated in detail. In this manner, the force sensing system serves as a powerful tool for coaches and sports scientists to make scientific researches on professional throwing techniques. It also provides an intuitive and reliable guidance for the throwing athletes to improve their skills.

  15. Vulnerability Identification and Design-Improvement-Feedback using Failure Analysis of Digital Control System Designs

    Lee, Eunchan; Bae, Yeonkyoung [Korea Hydro and Nuclear Power Co., Ltd., Daejeon (Korea, Republic of)

    2013-05-15

    Fault tree analyses let analysts establish the failure sequences of components as a logical model and confirm the result at the plant level. These two analyses provide insights regarding what improvements are needed to increase availability because it expresses the quantified design attribute of the system as minimal cut sets and availability value interfaced with component reliability data in the fault trees. This combined failure analysis method helps system users understand system characteristics including its weakness and strength in relation to faults in the design stage before system operation. This study explained why a digital system could have weaknesses in methods to transfer control signals or data and how those vulnerabilities could cause unexpected outputs. In particular, the result of the analysis confirmed that complex optical communication was not recommended for digital data transmission in the critical systems of nuclear power plants. Regarding loop controllers in Design A, a logic configuration should be changed to prevent spurious actuation due to a single failure, using hardware or software improvements such as cross checking between redundant modules, or diagnosis of the output signal integrity. Unavailability calculations support these insights from the failure analyses of the systems. In the near future, KHNP will perform failure mode and effect analyses in the design stage before purchasing non-safety-related digital system packages. In addition, the design requirements of the system will be confirmed based on evaluation of overall system availability or unavailability.

  16. Low-Power Low-Noise CMOS Imager Design : In Micro-Digital Sun Sensor Application

    Xie, N.

    2012-01-01

    A digital sun sensor is superior to an analog sun sensor in aspects of resolution, albedo immunity, and integration. The proposed Micro-Digital Sun Sensor (µDSS) is an autonomous digital sun sensor which is implemented by means of a CMOS image sensor, which is named APS+. The µDSS is designed

  17. Learning via Game Design: From Digital to Card Games and Back Again

    Marchetti, Emanuela; Valente, Andrea

    2015-01-01

    In this paper we consider the problem of making design of digital games accessible to primary school children and their teachers, and we argue for the need of digital games that are easy to alter by young learners. We know from previous research projects that digital games do not enable children to express their creativity at full, in contrast…

  18. Fast digital zooming system using directionally adaptive image interpolation and restoration.

    Kang, Wonseok; Jeon, Jaehwan; Yu, Soohwan; Paik, Joonki

    2014-01-01

    This paper presents a fast digital zooming system for mobile consumer cameras using directionally adaptive image interpolation and restoration methods. The proposed interpolation algorithm performs edge refinement along the initially estimated edge orientation using directionally steerable filters. Either the directionally weighted linear or adaptive cubic-spline interpolation filter is then selectively used according to the refined edge orientation for removing jagged artifacts in the slanted edge region. A novel image restoration algorithm is also presented for removing blurring artifacts caused by the linear or cubic-spline interpolation using the directionally adaptive truncated constrained least squares (TCLS) filter. Both proposed steerable filter-based interpolation and the TCLS-based restoration filters have a finite impulse response (FIR) structure for real time processing in an image signal processing (ISP) chain. Experimental results show that the proposed digital zooming system provides high-quality magnified images with FIR filter-based fast computational structure.

  19. Evaluation of dimensions of diagnostic X-ray tube focal spots using direct digitalization

    Costa, Paulo R.; Furquim, Tania A.C.

    1996-01-01

    An image digitalization system is proposed as an alternative method for replacing direct exposure X-ray films on the evaluation of dimensions of diagnostic X-ray tube focal spots. Results of measurements are presented and compared to nominal values

  20. DIRECTIONAL WELL TRAJECTORY DESIGN: THE THEORITICAL ...

    user

    2016-10-04

    Oct 4, 2016 ... record presentation of a desired complex directional well trajectory, also from which the overall angle change. (dogleg) is observed not to ... example; 23oNE means 23 degrees East from North, .... Azimuth Angles Selection.

  1. Examining design management in the era of digitalization from eastern and western perspectives

    Hwangbo, Hyunwook; Cooper, Rachel; Tsekleves, Emmanuel

    2015-01-01

    This thesis investigates how approaches to managing design differ nationally in new product development and design for digital technology-embedded product and service. The main aim of this thesis is, first, to understand different approaches to managing design in terms of Eastern and Western organizational cultures: second, how these differences affect actual design practices and design outcomes in increasingly complicated digital technology-embedded product development and design. Currently,...

  2. Digital Sensor Technology

    Ted Quinn; Jerry Mauck; Richard Bockhorst; Ken Thomas

    2013-07-01

    The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy, reliability, availability, and maintainability. This report demonstrates these benefits in direct comparisons of digital and analog sensor applications. It also addresses the qualification issues that must be addressed in the application of digital sensor technology.

  3. Faster processing of multiple spatially-heterodyned direct to digital holograms

    Hanson, Gregory R [Clinton, TN; Bingham, Philip R [Knoxville, TN

    2008-09-09

    Systems and methods are described for faster processing of multiple spatially-heterodyned direct to digital holograms. A method includes of obtaining multiple spatially-heterodyned holograms, includes: digitally recording a first spatially-heterodyned hologram including spatial heterodyne fringes for Fourier analysis; digitally recording a second spatially-heterodyned hologram including spatial heterodyne fringes for Fourier analysis; Fourier analyzing the recorded first spatially-heterodyned hologram by shifting a first original origin of the recorded first spatially-heterodyned hologram including spatial heterodyne fringes in Fourier space to sit on top of a spatial-heterodyne carrier frequency defined as a first angle between a first reference beam and a first object beam; applying a first digital filter to cut off signals around the first original origin and performing an inverse Fourier transform on the result; Fourier analyzing the recorded second spatially-heterodyned hologram by shifting a second original origin of the recorded second spatially-heterodyned hologram including spatial heterodyne fringes in Fourier space to sit on top of a spatial-heterodyne carrier frequency defined as a second angle between a second reference beam and a second object beam; and applying a second digital filter to cut off signals around the second original origin and performing an inverse Fourier transform on the result, wherein digitally recording the first spatially-heterodyned hologram is completed before digitally recording the second spatially-heterodyned hologram and a single digital image includes both the first spatially-heterodyned hologram and the second spatially-heterodyned hologram.

  4. The Use of the Digital Smile Design Concept as an Auxiliary Tool in Aesthetic Rehabilitation: A Case Report.

    Zanardi, Piero Rocha; Laia Rocha Zanardi, Raquel; Chaib Stegun, Roberto; Sesma, Newton; Costa, Bru-No; Cruz Laganá, Dalva

    2016-01-01

    The digital smile design is a practical diagnosis method that can assist the clinician to visualize and measure dentogingival discrepancies. This clinical report aims to present the associated steps, from the diagnosis of the alterations diagnosis through to the final aesthetic result. A 37-years-old female patient presented as her main complaint the tooth form and colour discrepancies. Applying the digital smile design principle, the necessary measures for a harmonic smile correction could be accurately determined. The initial diagnosis led to a wax up of the master cast that was duplicated in acrylic resin directly in the mouth. This temporary restoration guided the periodontal surgery and the final pressed ceramic crown restoration. We conclude that the digital smile design concept seems to be a useful tool to achieve a satisfactory aesthetic result.

  5. Applying Human Factors Evaluation and Design Guidance to a Nuclear Power Plant Digital Control System

    Thomas Ulrich; Ronald Boring; William Phoenix; Emily Dehority; Tim Whiting; Jonathan Morrell; Rhett Backstrom

    2012-08-01

    The United States (U.S.) nuclear industry, like similar process control industries, has moved toward upgrading its control rooms. The upgraded control rooms typically feature digital control system (DCS) displays embedded in the panels. These displays gather information from the system and represent that information on a single display surface. In this manner, the DCS combines many previously separate analog indicators and controls into a single digital display, whereby the operators can toggle between multiple windows to monitor and control different aspects of the plant. The design of the DCS depends on the function of the system it monitors, but revolves around presenting the information most germane to an operator at any point in time. DCSs require a carefully designed human system interface. This report centers on redesigning existing DCS displays for an example chemical volume control system (CVCS) at a U.S. nuclear power plant. The crucial nature of the CVCS, which controls coolant levels and boration in the primary system, requires a thorough human factors evaluation of its supporting DCS. The initial digital controls being developed for the DCSs tend to directly mimic the former analog controls. There are, however, unique operator interactions with a digital vs. analog interface, and the differences have not always been carefully factored in the translation of an analog interface to a replacement DCS. To ensure safety, efficiency, and usability of the emerging DCSs, a human factors usability evaluation was conducted on a CVCS DCS currently being used and refined at an existing U.S. nuclear power plant. Subject matter experts from process control engineering, software development, and human factors evaluated the DCS displays to document potential usability issues and propose design recommendations. The evaluation yielded 167 potential usability issues with the DCS. These issues should not be considered operator performance problems but rather opportunities

  6. Digital Sketch Modelling: Integrating Digital Sketching as a Transition between Sketching and CAD in Industrial Design Education

    Ranscombe, Charlie; Bissett-Johnson, Katherine

    2017-01-01

    Literature on the use of design tools in educational settings notes an uneasy relationship between student use of traditional hand sketching and digital modelling tools (CAD) during the industrial design process. This is often manifested in the transition from sketching to CAD and exacerbated by a preference of current students to use CAD. In this…

  7. New directions in cognitive educational game design

    Bril, Ivo; Degens, Nick; Braad, Eelco; Allison, Colin; Morgado, Leonel; Pirker, Johanna; Beck, Dennis; Richter, Jonathon; Gütl, Christian

    2016-01-01

    What makes an educational game good? This paper describes three research directions that could provide insight in the underlying principles of effective educational games. These aspects are 1) The importance of distinguishing between types of to-be-learned knowledge, 2) the need to understand the

  8. Challenges in Governing the Digital Transportation Ecosystem in Jakarta: A Research Direction in Smart City Frameworks

    Iqbal Yulizar Mukti

    2018-03-01

    Full Text Available Mobility is one of the most difficult domains of the smart city to face. In fact, most large cities in the world are still facing urban mobility problems, especially traffic congestion. Particularly, in Jakarta, Indonesia, traffic congestion is a major issue that negatively affects productivity and the overall living quality of the citizens. Along with the development of the information communication and technology (ICT, the transportation domain in Jakarta has formed a digital transportation ecosystem, shown by the emergence of innovative digital-based transportation services. In line with this current condition, this paper hopes to contribute to the improvement of urban traffic in Jakarta by proposing research directions to govern the digital transportation ecosystem within a smart city framework. The significance of the research directions is reviewed using Preferred Reporting Items for Systematic Reviews and Meta-Analyses (PRISMA methodology in a systematic review of previous studies. Ultimately, the research directions proposed in this paper lead to the necessity for an architectural perspective and relevant big data analytical tools to improve the digital transportation ecosystem in Jakarta.

  9. INFORMED DESIGN DECISION-MAKING: FROM DIGITAL ANALYSIS TO URBAN DESIGN

    Camilla Pezzica

    2017-11-01

    Full Text Available This study describes a new approach to explore the design of public open spaces based on a multidimensional analysis useful to inform decision-making and foster the development of evidence-based architectural solutions. It presents an overview of the most relevant design variables and their constraints, providing, in this way, valuable information for the elaboration of a more sustainable urban design, considerate of the local socio-cultural values. This research aims at providing holistic guidance for the development of better design proposals in contemporary urban environments. More specifically, it seeks to synchronously characterize urban spaces at a multi-scale and multidimensional level, both quantitatively and qualitatively, by collecting contributions from Space Syntax Theory, Public Life Studies, Building Science and Environmental/Comfort Analysis in public open spaces. Many advanced digital tools are used for data management purposes and to generate and test iteratively different design proposals. The proposed methodology is based on a range of tests and analyses performed in the process of developing a new experimental project for Largo da Graça, an urban square located in Lisbon’s historic centre, which allowed the testing of different design solutions. This experiment generated a digital workflow for the design of the urban square, in which are registered all the steps undertaken to solve the many design problems identified by considering the efficiency targets (centrality, connectivity, enclosure, thermal comfort, security, social equity and interaction. The process comprises a sequence of comparative design reviews and records the choices made when dealing with latent information underlying changing conditions in the use of public space and the programmatic malleability of the Portuguese plaza. The description of the adopted design strategy and the examples extracted from the workflow are used to illustrate the practical

  10. Directives and general design requirements for a small PWR

    Arrieta, L.A.

    1992-08-01

    A proposal of directives and general requirements for the development of a small PWR conceptual design is presented. These directives address the main safety, performance and economic design aspects. The purpose is to use this work as a base for a wide discussion, involving all project participants, culminating with the definition of the final directives and general requirements. (author)

  11. Design Optimization of Moving Magnet Actuated Valves for Digital Displacement Machines

    Madsen, Esben Lundø; Jørgensen, Janus Martin Thastum; Nørgård, Christian

    2017-01-01

    High-efficiency hydraulic machines using digital valves are presently a topic of great focus. Digital valve performance with respect to pressure loss, closing time as well as electrical power consumption, is key to obtaining high efficiency. A recent digital seat valve design developed at Aalborg...... optimized design closes in 2.1 ms, has a pressure drop of 0.8 bar at 150 l/min and yields a digital displacement machine average chamber efficiency of 98.9%. The design is simple in construction and uses a single coil, positioned outside the pressure chamber, eliminating the need for an electrical interface...

  12. A Modified Design of a Thermocouple Based Digital Temperature Indicator with Opto-Isolation

    S. C. BERA

    2008-01-01

    Full Text Available In the conventional thermocouple based digital temperature indicator the millivolt signal obtained from a thermocouple is first amplified and then converted into a digital signal by using analog-to-digital converter (ADC. This digital signal is then indicated as digital display of temperature using digital counter circuit or microprocessor/microcontroller based circuitry. In the present paper a modified AD conversion technique along with opto-isolation is used to indicate digitally the temperature without using any conventional analog-to-digital converter. The theory and design of the measuring technique are described in the paper. The non-linearity of thermocouple is eliminated by using look-up table within software program. The performance of the circuit has been experimentally tested by using mV input signal instead of a thermocouple as well as using a K-type thermocouple. The experimental results are reported in the paper.

  13. Collaboration Between Art Teacher Students and Communication and Digital Media Students Promoting Subject Specific Didactics in Digital Visual Learning Design

    Buhl, Mie; Skov, Kirsten

    . Student art teachers and teacher trainers took part in the design process performed by communication students. The project took its point of the departure in the act of Danish teacher education where student teachers must be educated in the practical use of digital visual media for art practices aiming......, drawing or video. Thus, the project suggested the development of a visual learning design for achieving augmented reality (AR) experiences in urban environments and sharing them on social media. The purpose was to explore adequate approaches to work with digital media in visual arts education based...... on practices and reflective processes. The theoretical framework for our discussion of the empirical project draws on current discussions of learning designs and digital media in visual arts education (Peppler 2010, Rasmussen 2015, Buhl & Ejsing-Duun, 2015; Buhl, 2016). Methodology The choice of empirical...

  14. Mechanical system design in the engineering design of digital x-ray

    Muhammad Awwaluddin; I Putu Susila; Edy Purwanta; Abdul Jalil; Ahmad H

    2014-01-01

    Has been designed a mechanical system design to hold and moving the x-ray tube, detector films, and a place the holder control box. The design was conducted on the frame foundation, frame columns and frame arms in order to operate the device as well SS304 hollow measuring 40 x 60 x mm with thickness of 2 mm long 4.1 m, size 100 x 100 mm and 2 mm thick along the 2 m, and the size of 40 x 80 mm thickness 2 mm long 1.8 m is needed to reactive the design the linear guide way models HGW20HB 3 m. With the proposed design, the operation of the digital x-rays can be completed as well. (author)

  15. Digitization

    Finnemann, Niels Ole

    2014-01-01

    what a concept of digital media might add to the understanding of processes of mediatization and what the concept of mediatization might add to the understanding of digital media. It is argued that digital media open an array of new trajectories in human communication, trajectories which were...

  16. Empirical direction in design and analysis

    Anderson, Norman H

    2001-01-01

    The goal of Norman H. Anderson's new book is to help students develop skills of scientific inference. To accomplish this he organized the book around the ""Experimental Pyramid""--six levels that represent a hierarchy of considerations in empirical investigation--conceptual framework, phenomena, behavior, measurement, design, and statistical inference. To facilitate conceptual and empirical understanding, Anderson de-emphasizes computational formulas and null hypothesis testing. Other features include: *emphasis on visual inspection as a basic skill in experimental analysis to help student

  17. Digital health increasing the impact with personalized design

    Empelen, P. van; Otten, W.; Molema, H.; Keijsers, J.; Mooij, R.

    2016-01-01

    Digital health is considered the ‘holy grail’ of effective and sustainable health(care). It uses the latest technology, apps and data to support and improve health. Digital health tools can benefit both patients and healthy individuals, with support and advice. But healthcare professionals,

  18. Preliminary Design Study for a National Digital Seismograph Network

    Peterson, Jon; Hutt, Charles R.

    1981-01-01

    Introduction Recently, the National Research Council published a report by the Panel on National, Regional, and Local Seismograph Networks of the Committee on Seismology in which the principal recommendation was for the establishment of a national digital seismograph network (NDSN). The Panel Report (Bolt, 1980) addresses both the need and the scientific requirements for the new national network. The purpose of this study has been to translate the scientific requirements into an instrumentation concept for the NSDS. There are literally hundreds, perhaps thousands, of seismographs in operation within the United States. Each serves an important purpose, but most have limited objectives in time, in region, or in the types of data that are being recorded. The concept of a national network, funded and operated by the Federal Government, is based on broader objectives that include continuity of time, uniform coverage, standardization of data format and instruments, and widespread use of the data for a variety of research purposes. A national digital seismograph network will be an important data resource for many years to come; hence, its design is likely to be of interest to most seismologists. Seismologists have traditionally been involved in the development and field operation of seismic systems and thus have been familiar with both the potential value and the limitations of the data. However, in recent years of increasing technological sophistication, the development of data sstems has fallen more to system engineers, and this trend is likely to continue. One danger in this is that the engineers may misinterpret scientific objectives or subordinate them to purely technological considerations. Another risk is that the data users may misuse or misinterpret the data because they are not aware of the limitations of the data system. Perhaps the most important purpose of a design study such as this is to stimulate a dialogue between system engineers and potential data users

  19. Development of basic technology for instrumentation and control - Development of digital automatic supervisory limitation system and its design= validation

    Choi, Jung In; Chung, Sung Wook; Koh, Won Seok [Kyungwon University, Sungman (Korea, Republic of); Suh, Duk Young; Cheon, Sei Young [Kyunghee University, Seoul (Korea, Republic of); Lee, Sang Kyung; Kim, Sung Hun [Seoul National University, Seoul (Korea, Republic of)

    1995-07-01

    A major objective of the project is to develop a digital automatic supervisory limitation system and validate its design for the next generation= nuclear power plant. The limitation system assures that the plant does not exceed the operating limits by regulation the plant operations through on-line monitoring the operating margins of the critical parameters. A new conceptual model of power maneuverability has been proposed for the design of the limitation system and for its validation. Also, the limitation system monitors overall operation processes throughout a nuclear power plant by implementing hierarchical communication networks. Based on the conceptual design in software of the 1 st year results, the detailed design of the limitation system has been performed during the 2 nd year with constructing a prototype digital system. The system consists of the software module for plant simulation and the hardware module for implementation of limitation system and the associated interfaces in hardware. The limitation algorithm were implemented into the microprocessor and the interfaces were realized through the I/O modules. Also, these modules are incorporated into the communication networks. The products of the project could be directly applicable to the following nuclear unit adopting the limitation system, providing the bumpless transition to the commercial design phase. And the prototype evaluation scheme will be very useful for the succeeding studies related to the digital nuclear I and C fields, such as fault-tolerance design methods, software verification and validation and response time execution of digital systems. 69 refs., 3 tabs., 44 figs. (author)

  20. Collaboration between student art teachers and communication and digital media students promoting subject specific didactics in digital visual learning design

    Skov, Kirsten; Buhl, Mie

    into account. Our discussion of the potential for developing digital learning application from a collaborative approach is based on the visual design products, interviews and written reports, as well as shared experiences from the stakeholders in the project. Results: The project revealed three digital visual......=pdf Dunleavy, M. & Dede, C. (2014). Augmented reality teaching and learning. in. J.M. Spector, M.D. Merrill, J. Elen & M.J. Bishop (eds), The handbook og research for educational communications and technology New York: Springer http://isites.harvard.edu/fs/docs/icb.topic1116077.files....../DunleavyDedeARfinal.pdf Rasmussen, H. (2015). Digital Picture Production and Picture aesthetic Competency in It-didactic Design. Risk and opportunities for visual arts education in Europe. Proceedings, InSEA conferene, Lisbon, Portugal...

  1. Human factors issues in digital system design and implementation

    Galletti, Greg S.

    1998-01-01

    A goal of the U.S. Nuclear Regulatory Commission (NRC) is to ensure safety in the application of digital equipment upgrades to nuclear power plant control rooms and local control stations. One of the areas of specific interest is the integration of digital technology into existing analog control, display, and information systems and the implications of such integration for operators in regard to their use of this new equipment to safely operate the plant. This paper is a discussion of human performance issues related to the introduction of such digital equipment into operating nuclear power plants. (author)

  2. Quality comparison of direct digital panoramic radiography and computed radiography panoramic

    Dariush Goodarzipour

    2013-09-01

    Full Text Available BACKGROUND AND AIM: Digital panoramic X-ray images can be captured using photostimulable phosphors or solid-state detectors (i.e. charge-coupled devices and Flat-Panels. The first category is defined as computed radiography (CR or semi-direct radiography. The second technology that uses solid-state detectors is known as direct digital radiography (DDR. Both of these technologies have their own advantages and disadvantages. One of the most important fields in comparison of these systems is their resultant image quality. The purpose of this study was to compare the subjective image quality of DDR and CR digital panoramic system, and to assess the overall density and contrast of their images. METHODS: 200 patients were randomly allocated to two digital systems: Promax [central control digital (CCD] and XC [photostimulable phosphor plates (PSP]. Image quality was evaluated in six regions on a 3-point scale by three oral and maxillofacial radiologists independently. In addition, observers assessed overall density and contrast of each image on a 3-point scale. RESULTS: Using chi-square test, no statistically significant differences were found (P >0.05 in subjective image quality of anatomic structures between the two radiographic systems. But DDR system outperformed CR system in overall density and contrast of the image. P values for both overall density and contrast of the images was less than 0.001. CONCLUSIONS: The subjective image quality of CR and DDR panoramic systems in specified anatomic regions were found statistically comparable in this study. In overall density and contrast of the radiographs, DDR system proved better than CR system.

  3. Design for the human-machine interface of a digitalized reactor control-room

    Qu Ronghong; Zhang Liangju; Li Duo; Yu Hui

    2005-01-01

    Digitalized technology is implemented in the instrumentation and control system of an in-construction research reactor, which advances information display in both contents and styles in a nuclear reactor control-room, and greatly improves human-machine interface. In the design for a digitalized nuclear reactor control-room there are a series of new problems and technologies should be considered seriously. This paper mainly introduces the design for the digitalized control-room of the research nuclear reactor and covered topics include design principle of human-machine interface, organization and classification of interface graphics, technologies and principles based on human factors engineering and implemented in the graphics design. (authors)

  4. Cardinal principle and application practice of 3D digital model design for nuclear power plant

    Wang Ruobing; Wu Yan

    2005-01-01

    The practical application of 3D digital model design at nuclear power plants was introduced in detail in the paper. The whole process for system choice, program constitution, model design and project practice were also summarized. By demonstrating the cardinal principal and application practice of 3D digital model design as an important sub-project of CGNPC Digital Plant, the paper validates the rationality and validity of the major architecture system and program configuration of the digital plant, carries out beneficial attempt and study in the overall power plant life engineering management and site practice, and has achieved significant engineering and social benefits. The success of practices in the project accelerates the extended and extensive application of Digital Plant in the operation and maintenance simulation of Daya Bay and Ling'ao Nuclear Power Plants, and the engineering design management for Ling'ao II and III of CGNPC on a consolidated basis. (authors)

  5. Based on the Network Technology of Digital Campus Design and Analysis

    Guo Hongbin

    2016-09-01

    Full Text Available In recent years, in order to meet the trend of popularization of higher education, expanding the scale of Chinese colleges and universities, and lead to university campuses scattered teaching resources, and information to be slow, poor accuracy and efficiency of the office problems have emerged. The construction of digital campus is not only working for the university scientific research, management provides a fast and convenient information service, and realize the education space and time, teaching contents, means and forms of further opening, largely improves the ability of teaching and scientific research ability and management level. This article through to the digital campus in the process of planning and design requirements, puts forward the conception and design of the construction of the digital campus network, then the digital campus network topology, design of core network, IP address assignment has carried on the discussion a rough. For the design of the digital campus construction provides a draft plan.

  6. 3D Digital Smile Design With a Mobile Phone and Intraoral Optical Scanner.

    Daher, René; Ardu, Stefano; Vjero, Osela; Krejci, Ivo

    2018-06-01

    Extraoral facial scanning using a mobile phone has emerged as a viable, cost-effective option for certain applications not requiring high precision, such as patient education and 3-dimensional (3D) digital smile design. This technological development is particularly promising for general practitioners (GPs) who may not be able to invest in expensive,complex digital impressioning devices. This article describes and illustrates a relatively simple and accessible workflow that avails digital 3D facial scanning benefits to GPs.

  7. Device and Circuit Design Challenges in the Digital Subthreshold Region for Ultralow-Power Applications

    Ramesh Vaddi

    2009-01-01

    Full Text Available In recent years, subthreshold operation has gained a lot of attention due to ultra low-power consumption in applications requiring low to medium performance. It has also been shown that by optimizing the device structure, power consumption of digital subthreshold logic can be further minimized while improving its performance. Therefore, subthreshold circuit design is very promising for future ultra low-energy sensor applications as well as high-performance parallel processing. This paper deals with various device and circuit design challenges associated with the state of the art in optimal digital subthreshold circuit design and reviews device design methodologies and circuit topologies for optimal digital subthreshold operation. This paper identifies the suitable candidates for subthreshold operation at device and circuit levels for optimal subthreshold circuit design and provides an effective roadmap for digital designers interested to work with ultra low-power applications.

  8. Digital design of scaffold for mandibular defect repair based on tissue engineering.

    Liu, Yun-feng; Zhu, Fu-dong; Dong, Xing-tao; Peng, Wei

    2011-09-01

    Mandibular defect occurs more frequently in recent years, and clinical repair operations via bone transplantation are difficult to be further improved due to some intrinsic flaws. Tissue engineering, which is a hot research field of biomedical engineering, provides a new direction for mandibular defect repair. As the basis and key part of tissue engineering, scaffolds have been widely and deeply studied in regards to the basic theory, as well as the principle of biomaterial, structure, design, and fabrication method. However, little research is targeted at tissue regeneration for clinic repair operations. Since mandibular bone has a special structure, rather than uniform and regular structure in existing studies, a methodology based on tissue engineering is proposed for mandibular defect repair in this paper. Key steps regarding scaffold digital design, such as external shape design and internal microstructure design directly based on triangular meshes are discussed in detail. By analyzing the theoretical model and the measured data from the test parts fabricated by rapid prototyping, the feasibility and effectiveness of the proposed methodology are properly verified. More works about mechanical and biological improvements need to be done to promote its clinical application in future.

  9. Digital design of scaffold for mandibular defect repair based on tissue engineering

    Yun-feng LIU; Fu-dong ZHU; Xing-tao DONG; Wei PENG

    2011-01-01

    Mandibular defect occurs more frequently in recent years,and clinical repair operations via bone transplantation are difficult to be further improved due to some intrinsic flaws.Tissue engineering,which is a hot research field of biomedical engineering,provides a new direction for mandibular defect repair.As the basis and key part of tissue engineering,scaffolds have been widely and deeply studied in regards to the basic theory,as well as the principle of biomaterial,structure,design,and fabrication method.However,little research is targeted at tissue regeneration for clinic repair operations.Since mandibular bone has a special structure,rather than uniform and regular structure in existing studies,a methodology based on tissue engineering is proposed for mandibular defect repair in this paper.Key steps regarding scaffold digital design,such as external shape design and internal microstructure design directly based on triangular meshes are discussed in detail.By analyzing the theoretical model and the measured data from the test parts fabricated by rapid prototyping,the feasibility and effectiveness of the proposed methodology are properly verified.More works about mechanical and biological improvements need to be done to promote its clinical application in future.

  10. Digital Living at Home

    Andersen, Pernille Viktoria Kathja; Christiansen, Ellen Tove

    2013-01-01

    of these user voices has directed us towards a ‘home-keeping’ design discourse, which opens new horizons for design of digital home control systems by allowing users to perform as self-determined controllers and groomers of their habitat. The paper concludes by outlining the implications of a ‘home......Does living with digital technology inevitably lead to digital living? Users talking about a digital home control system, they have had in their homes for eight years, indicate that there is more to living with digital technology than a functional-operational grip on regulation. Our analysis......-keeping’ design discourse....

  11. Digital logic circuit design with ALTERA MAX+PLUS II

    Lee, Seung Ho; Park, Yong Su; Lee, Ju Heon

    2006-03-01

    Contents of this book are the kinds of integrated circuit, design process of integrated circuit, introduction of ALTERA MAX+PLUS II, designing logic circuit with VHDL of ALTERA MAX+PLUS II, grammar and practice of VHDL of ALTERA MAX+PLUS II, design for adder, subtractor, parallel binary subtractor, BCD design, CLA design, code converter design, ALU design, register design, counter design, accumulator design, state machine design, frequency divider design, circuit design with TENMILLION counter, LCD module, circuit design for control the outside RAM in training kit and introduction for HEB-DTK-20K-240/HBE-DTK-IOK.

  12. A REVIEW OF HUMAN-SYSTEM INTERFACE DESIGN ISSUES OBSERVED DURING ANALOG-TO-DIGITAL AND DIGITAL-TO-DIGITAL MIGRATIONS IN U.S. NUCLEAR POWER PLANTS

    Kovesdi, C.; Joe, J.

    2017-05-01

    The United States (U.S.) Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) program is developing a scientific basis through targeted research and development (R&D) to support the U.S. nuclear power plant (NPP) fleet in extending their existing licensing period and ensuring their long-term reliability, productivity, safety, and security. Over the last several years, human factors engineering (HFE) professionals at the Idaho National Laboratory (INL) have supported the LWRS Advanced Instrumentation, Information, and Control (II&C) System Technologies pathway across several U.S. commercial NPPs in analog-to-digital migrations (i.e., turbine control systems) and digital-to-digital migrations (i.e., Safety Parameter Display System). These efforts have included in-depth human factors evaluation of proposed human-system interface (HSI) design concepts against established U.S. Nuclear Regulatory Commission (NRC) design guidelines from NUREG-0700, Rev 2 to inform subsequent HSI design prior to transitioning into Verification and Validation. This paper discusses some of the overarching design issues observed from these past HFE evaluations. In addition, this work presents some observed challenges such as common tradeoffs utilities are likely to face when introducing new HSI technologies into NPP hybrid control rooms. The primary purpose of this work is to distill these observed design issues into general HSI design guidance that industry can use in early stages of HSI design.

  13. Designing for Motivation, Engagement and Wellbeing in Digital Experience

    Dorian Peters

    2018-05-01

    Full Text Available Research in psychology has shown that both motivation and wellbeing are contingent on the satisfaction of certain psychological needs. Yet, despite a long-standing pursuit in human-computer interaction (HCI for design strategies that foster sustained engagement, behavior change and wellbeing, the basic psychological needs shown to mediate these outcomes are rarely taken into account. This is possibly due to the lack of a clear model to explain these needs in the context of HCI. Herein we introduce such a model: Motivation, Engagement and Thriving in User Experience (METUX. The model provides a framework grounded in psychological research that can allow HCI researchers and practitioners to form actionable insights with respect to how technology designs support or undermine basic psychological needs, thereby increasing motivation and engagement, and ultimately, improving user wellbeing. We propose that in order to address wellbeing, psychological needs must be considered within five different spheres of analysis including: at the point of technology adoption, during interaction with the interface, as a result of engagement with technology-specific tasks, as part of the technology-supported behavior, and as part of an individual's life overall. These five spheres of experience sit within a sixth, society, which encompasses both direct and collateral effects of technology use as well as non-user experiences. We build this model based on existing evidence for basic psychological need satisfaction, including evidence within the context of the workplace, computer games, and health. We extend and hone these ideas to provide practical advice for designers along with real world examples of how to apply the model to design practice.

  14. Long-term in-vitro precision of direct digital X-ray radiogrammetry

    Dhainaut, Alvilde; Hoff, Mari; Kaelvesten, Johan; Lydersen, Stian; Forslind, Kristina; Haugeberg, Glenn

    2011-01-01

    Digital X-ray radiogrammetry (DXR) calculates peripheral bone mineral density (BMD) from hand radiographs. The short-term precision for direct DXR has been reported to be highly satisfactory. However, long-term precision for this method has not been examined. Thus, the aim of this study was to examine the long-term in-vitro precision for the new direct digital version of DXR. The in-vitro precision for direct DXR was tested with cadaver phantoms on four different X-ray systems at baseline, 3 months, 6 months, and in one machine also at 12 months. At each time point, 31 measurements were performed. The in-vitro longitudinal precision for the four radiographic systems ranged from 0.22 to 0.43% expressed as coefficient of variation (CV%). The smallest detectable difference (SDD) ranged from 0.0034 to 0.0054 g/cm 2 . The in vitro long-term precision for direct DXR was comparable to the previous reported short-term in-vitro precision for all tested X-ray systems. These data show that DXR is a stable method for detecting small changes in bone density during 6-12 months of follow-up. (orig.)

  15. An Integrative Framework for Studying, Designing and Conceptualising Interactivity in Children's Digital Books

    Kucirkova, Natalia

    2017-01-01

    In the past five years, there have been significant changes concerning the material and design properties of digital books, with an impact on children's enjoyment and learning from reading on screen. Despite the rapid advances in technology, research on children's digital books is disjointed. This is because of no consistent approach to the study…

  16. Design Strategy for a Pipelined ADC Employing Digital Post-correction

    Harpe, P.J.A.; Zanikopoulos, A.; Hegt, J.A.; Roermund, van A.H.M.

    2004-01-01

    This paper describes how the usage of digital post-correction techniques in pipelined analog-to-digital converters (ADC's) can be exploited optimally during the design-phase of the converter. It is known that post-correction algorithms reduce the influence of several cir- cuit impairments on the

  17. Digital Games for Young Children Ages Three to Six: From Research to Design

    Lieberman, Debra A.; Fisk, Maria Chesley; Biely, Erica

    2009-01-01

    Young children ages 3 to 6 play a wide range of digital games, which are now available on large screens, handheld screens, electronic learning systems, and electronic toys, and their time spent with games is growing. This article examines effects of digital games and how they could be designed to best serve children's needs. A small body of…

  18. Applying the Digital Doorway design research model in facilitating skills transfer in rural communities

    Herselman, ME

    2010-11-01

    Full Text Available The purpose of this article is to indicate how skills can be transferred through the application of the Digital Doorway (DD) design research model. Skills transfer takes place between the initiators of Digital Doorway (CSIR Meraka Institute) project...

  19. Digital technology use in ELT classrooms and self-directed learning

    Nehir Sert

    2016-04-01

    Full Text Available The digital era is a new challenge for teachers. While children get acquainted with digital technology before the age of six, teachers, who have encountered the digital world at a later time in their lives, struggle with it. Self-directed learning, which is crucial for lifelong learning, can be enhanced by the use of technology within and beyond classroom settings. The aim of this study was to examine the difference between the perceptions of students in low- and high-income groups about their use of technology in a general sense and their teachers’ use of technology in ELT classrooms. It also tested the correlation between the perceptions of their self-directed learning behaviours and their own/their teachers’ technology use. The population of the study consisted of 75 students from high- and 70 students from low-income groups. Causal comparative and correlational research methods were adopted in the study. The surveys to measure the students’ perceptions about technology use were developed by the researchers. A scale, established by Demirtas and Sert (2010, was used to identify the level of self-directed learning views of the students. The data were collected at the beginning of the first term of the 2015-2016 school year. The results indicated that there was no significant difference between perceptions of the low- and high-income students regarding their own technology use. Likewise, perceptions of the low- and high-income students did not differ regarding their teachers’ technology use. There was no correlation between the perceptions of the low-/high-income mixed group regarding their use of technology and their teachers’ use of technology. Lastly, self-directed learning perceptions of the low-/high-income mixed group did not correlate with their perceptions on any aspects of technology use. The educational implications of these results were discussed and suggestions were put forward in order to produce more effective learning

  20. Design and implementation of a multiband digital filter using FPGA to extract the ECG signal in the presence of different interference signals.

    Aboutabikh, Kamal; Aboukerdah, Nader

    2015-07-01

    In this paper, we propose a practical way to synthesize and filter an ECG signal in the presence of four types of interference signals: (1) those arising from power networks with a fundamental frequency of 50Hz, (2) those arising from respiration, having a frequency range from 0.05 to 0.5Hz, (3) muscle signals with a frequency of 25Hz, and (4) white noise present within the ECG signal band. This was done by implementing a multiband digital filter (seven bands) of type FIR Multiband Least Squares using a digital programmable device (Cyclone II EP2C70F896C6 FPGA, Altera), which was placed on an education and development board (DE2-70, Terasic). This filter was designed using the VHDL language in the Quartus II 9.1 design environment. The proposed method depends on Direct Digital Frequency Synthesizers (DDFS) designed to synthesize the ECG signal and various interference signals. So that the synthetic ECG specifications would be closer to actual ECG signals after filtering, we designed in a single multiband digital filter instead of using three separate digital filters LPF, HPF, BSF. Thus all interference signals were removed with a single digital filter. The multiband digital filter results were studied using a digital oscilloscope to characterize input and output signals in the presence of differing sinusoidal interference signals and white noise. Copyright © 2015 Elsevier Ltd. All rights reserved.

  1. Rethinking Design Process: Using 3D Digital Models as an Interface in Collaborative Session

    Ding, Suining

    2008-01-01

    This paper describes a pilot study for an alternative design process by integrating a designer-user collaborative session with digital models. The collaborative session took place in a 3D AutoCAD class for a real world project. The 3D models served as an interface for designer-user collaboration during the design process. Students not only learned…

  2. The (digital) natives are restless: designing and implementing an interactive digital media assignment.

    Voge, Catherine; Hirvela, Kari; Jarzemsky, Paula

    2012-01-01

    To create an opportunity for students to connect with the Quality and Safety Education for Nurses competencies and demonstrate learning via knowledge transference, the authors piloted a digital media assignment. Students worked in small groups to create an unfolding patient care scenario with embedded decision points, using presentation software. The authors discuss the assignment and its outcomes.

  3. The Design of Application-Specific Heuristics for the Usability Evaluation of the Digital Doorway

    Funmi Adebesin

    2012-06-01

    Full Text Available The Digital Doorway (DD is a joint initiative between the South African Department of Science and Technology (DST and the Meraka Institute of the Council for Scientific and Industrial Research (CSIR. The DD is a non-standard computer system deployed amongst underprivileged communities in South Africa with the objective to promote computer literacy. Since its inception, there has been no usability or accessibility evaluation of the software installed on the DD, mainly due to lack of usability engineering or interaction design expertise within the development team. The goal of the research presented in this paper was to design a solution to this problem by developing a suitable instrument that could guide DD application developers in the design and development of more usable DD software and interfaces. Design research was used as a research methodology. We first investigated the applicability of the standard usability and accessibility evaluation methods for evaluating the software installed on the DD. During the first cycle of design research, we established that a heuristic-like evaluation method would be an appropriate method for evaluating the usability and direct accessibility support provided by the DD. During a second cycle of design research, embedded in the first, we also developed a set of multi-category heuristics as the ‘instrument’ that could guide the developers during design of applications as well as in the first-level (formative evaluation thereof. To verify the heuristics, we conducted a usability evaluation of the DD and triangulated the results with a direct field observation at a natural environment of DD use, together with user-administered questionnaires.

  4. Digital signal display board design: A knowledge based study

    Chaitanya, V. Sree Krishna; Rao, C. Raghavendra

    2007-01-01

    The digital signal display board is assumed to be composed of picture tubes for the purpose of displaying characters. The signal board with the picture tubes constitutes an Information System. A methodology for obtaining the discrimable matrix or table (more decisive attributes) and knowledge reduction for the above information system is proposed

  5. Reconfigurable digital receiver design and application for instantaneous polarimetric measurement

    Wang, Z.; Krasnov, O.A.; Babur, G.P.; Ligthart, L.P.; Van der Zwan, F.

    2011-01-01

    This paper presents the development of a reconfigurable receiver to undertake challenging signal processing tasks for a novel polarimetric radar system. The field-programmable gate arrays (FPGAs)-based digital receiver samples incoming signals at intermediate frequency (IF) and processes signals

  6. Automated Design of Board and MCM Level Digital Systems.

    1997-10-01

    Object- Oriented Programming, 7(6):39-49, October 1994. 46 December 14, 1994 33 [3] Stephen J. Garland, John V. Guttag, and James J. Horning...of Digital Circuits. Mc Graw Hill, 1994. 15 APPENDIX G: ... 93 Multicomponent Partitioning for VLSI System Synthesis Nand Kumar and Ranga Vemuri

  7. Design method for a digitally trimmable MOS transistor structure

    Ning, Feng; Bruun, Erik

    1996-01-01

    A digitally trimmable MOS transistor is a MOS transistor consisting of a drain, a source, and a main gate as well as several subgates. The transconductance of the transistor is tunabledigitally by means of connecting subgates either to the main gate or to the source terminal. In this paper, a sys...

  8. What Learners "Know" through Digital Media Production: Learning by Design

    Mills, Kathy A.

    2010-01-01

    The power to influence others in ever expanding social networks in the new knowledge economy is tied to capabilities with digital media production that require increased technological knowledge. This article draws on research in primary classrooms to examine the repertoires of cross-disciplinary knowledge that literacy learners need to produce…

  9. Design and development of digital seismic amplifier recorder

    Samsidar, Siti Alaa; Afuar, Waldy; Handayani, Gunawan, E-mail: gunawanhandayani@gmail.com [Department of Physics, ITB (Indonesia)

    2015-04-16

    A digital seismic recording is a recording technique of seismic data in digital systems. This method is more convenient because it is more accurate than other methods of seismic recorders. To improve the quality of the results of seismic measurements, the signal needs to be amplified to obtain better subsurface images. The purpose of this study is to improve the accuracy of measurement by amplifying the input signal. We use seismic sensors/geophones with a frequency of 4.5 Hz. The signal is amplified by means of 12 units of non-inverting amplifier. The non-inverting amplifier using IC 741 with the resistor values 1KΩ and 1MΩ. The amplification results were 1,000 times. The results of signal amplification converted into digital by using the Analog Digital Converter (ADC). Quantitative analysis in this study was performed using the software Lab VIEW 8.6. The Lab VIEW 8.6 program was used to control the ADC. The results of qualitative analysis showed that the seismic conditioning can produce a large output, so that the data obtained is better than conventional data. This application can be used for geophysical methods that have low input voltage such as microtremor application.

  10. Design of digital learning material for bioprocess-engineering-education

    Schaaf, van der H.

    2007-01-01

    With the advance of computers and the internet, new types of learning material can be developed: web-based digital learning material. Because many complex learning objectives in the food- and bioprocess technology domain are difficult to achieve in a traditional learning environment, a project was

  11. Externalising memories : designing for digital mnemonic cue embodiment

    Gennip, van D.A.P.

    2013-01-01

    Doctoral Consortium paper and presentation. Remembering is vital to our self-image, how we express ourselves, and relate to others. Nowadays people have more tools available to help them remember, such as photos, messages, and souvenirs. Increasingly, media are stored digitally and because of low

  12. Developing 21st Century Chemistry Learning through Designing Digital Games

    Lay, Ah-Nam; Osman, Kamisah

    2018-01-01

    The purpose of this study is to investigate the effect of Malaysian "Kimia" (Chemistry) Digital Games (MyKimDG) module on students' achievement and motivation in chemistry as well as 21st century skills. Chemistry education in Malaysia should put greater emphasis on combination of cognitive, sociocultural and motivational aspects to…

  13. Seven-channel digital telemetry system for monitoring and direct computer capturing of biological data.

    Drewes, A M; Andreasen, A; Assentoft, J E; Nagel, O

    1993-09-01

    A seven-channel telemetry system for collection and display of biological data is presented. The system can amplify bioelectrical signals in the range of 2 microV to 200 mV and has a bandwidth of 0.1-80 Hz. After multiplexing, the signals are digitized with a resolution of 8 bits. The data are frequency modulated directly on a VHF transmitter. After receiving the data on a VHF receiver, they are routed directly to the RS232 input connector on the PC. Thereby the advantage of direct communication between the transmitter and the PC can be utilized. Expensive analog equipment is avoided and display of the signals on the PC screen as well as signal analysis can be performed. The system has been tested and was found to be stable and highly reliable.

  14. DIGITAL

    Federal Emergency Management Agency, Department of Homeland Security — The Digital Flood Insurance Rate Map (DFIRM) Database depicts flood risk information and supporting data used to develop the risk data. The primary risk...

  15. Research of Digital Interface Layout Design based on Eye-tracking

    Shao Jiang

    2015-01-01

    Full Text Available The aim of this paper is to improve the low service efficiency and unsmooth human-computer interaction caused by currently irrational layouts of digital interfaces for complex systems. Also, three common layout structures for digital interfaces are to be presented and five layout types appropriate for multilevel digital interfaces are to be summarized. Based on the eye tracking technology, an assessment was conducted in advantages and disadvantages of different layout types through subjects’ search efficiency. Based on data and results, this study constructed a matching model which is appropriate for multilevel digital interface layout and verified the fact that the task element is a significant and important aspect of layout design. A scientific experimental model of research on digital interfaces for complex systems is provided. Both data and conclusions of the eye movement experiment provide a reference for layout designs of interfaces for complex systems with different task characteristics.

  16. Realizing the increased potential of an open-system high-definition digital projector design

    Daniels, Reginald

    1999-05-01

    Modern video projectors are becoming more compact and capable. Various display technologies are very competitive and are delivering higher performance and more compact projectors to market at an ever quickening pace. However the end users are often left with the daunting task of integrating the 'off the self projectors' into a previously existing system. As the projectors become more digitally enhanced, there will be a series of designs, and the digital projector technology matures. The design solutions will be restricted by the state of the art at the time of manufacturing. In order to allow the most growth and performance for a given price, many design decisions will be made and revisited over a period of years or decades. A modular open digital system design concept is indeed a major challenge of the future high definition digital displays for al applications.

  17. Adaptive Digital Signature Design and Short-Data-Record Adaptive Filtering

    Pados, Dimitiris A

    2008-01-01

    This report covers the research performed to create and develop a digital signature design analysis and development methodology that will support robust multi-user communications in rapidly changing environments...

  18. Computer-aided design and manufacture of hyrax devices: Can we really go digital?

    Graf, Simon; Cornelis, Marie; Gameiro, Gustavo Hauber

    2017-01-01

    Highlights - New possibilities of CAD/CAM technologies in orthodontics are illustrated. - A hyrax appliance can be produced with a full digital work flow. - Finite element analysis showed that the design and material delivered the needed strength....

  19. A non-binary direct digital synthesizer with an extended phase accumulator.

    Nosaka, H; Yamaguchi, Y; Muraguchi, M

    2001-01-01

    We describe a new direct digital synthesizer (DDS) in which output tuning resolution is flexibly controlled. The new DDS has an extended phase accumulator (EPA) controlled by two frequency control words; one determines the wave number within a single EPA operation cycle, and the other determines the length of the cycle. The EPA allows the DDS to provide jitter-free signals, the frequencies of which are given by arbitrary fractional expressions. (The denominator is fixed in conventional DDS that use normal phase accumulators.) Experimental results showed that the EPA worked well, allowing flexible output tuning resolution.

  20. A digital computer simulation and study of a direct-energy-transfer power-conditioning system

    Burns, W. W., III; Owen, H. A., Jr.; Wilson, T. G.; Rodriguez, G. E.; Paulkovich, J.

    1975-01-01

    An investigation of the behavior of the power-conditioning system as a whole is a necessity to ensure the integrity of the aggregate system in the case of space applications. An approach for conducting such an investigation is considered. A description is given of the application of a general digital analog simulator program to the study of an aggregate power-conditioning system which is being developed for use on the International Ultraviolet Explorer spacecraft. The function of the direct energy transfer system studied involves a coupling of a solar array through a main distribution bus to the spacecraft electrical loads.

  1. An adaptive digital suppression filter for direct-sequence spread-spectrum communications

    Saulnier, G. J.; Das, P. K.; Milstein, L. B.

    1985-09-01

    This paper describes the structure of a digital implementation of the Widrow-Hoff LMS algorithm which uses a burst processing technique to obtain some hardware simplification. This adaptive system is used to suppress narrow-band interference in a direct-sequence spread-spectrum communication system. Several different narrow-band interferers are considered, and probability of error results are presented for all cases. While, in general, the results show significant improvement in performance when the LMS algorithm is used, certain disadvantages are also present and are discussed in this paper.

  2. Ethical Issues for Direct-to-Consumer Digital Psychotherapy Apps: Addressing Accountability, Data Protection, and Consent.

    Martinez-Martin, Nicole; Kreitmair, Karola

    2018-04-23

    This paper focuses on the ethical challenges presented by direct-to-consumer (DTC) digital psychotherapy services that do not involve oversight by a professional mental health provider. DTC digital psychotherapy services can potentially assist in improving access to mental health care for the many people who would otherwise not have the resources or ability to connect with a therapist. However, the lack of adequate regulation in this area exacerbates concerns over how safety, privacy, accountability, and other ethical obligations to protect an individual in therapy are addressed within these services. In the traditional therapeutic relationship, there are ethical obligations that serve to protect the interests of the client and provide warnings. In contrast, in a DTC therapy app, there are no clear lines of accountability or associated ethical obligations to protect the user seeking mental health services. The types of DTC services that present ethical challenges include apps that use a digital platform to connect users to minimally trained nonprofessional counselors, as well as services that provide counseling steered by artificial intelligence and conversational agents. There is a need for adequate oversight of DTC nonprofessional psychotherapy services and additional empirical research to inform policy that will provide protection to the consumer. ©Nicole Martinez-Martin, Karola Kreitmair. Originally published in JMIR Mental Health (http://mental.jmir.org), 23.04.2018.

  3. Design and radiation tests on a LED based emergency evacuation directional lighting

    Trikoupis, Nikolaos

    2017-01-01

    A LED (Light Emitting Diode) based directional lighting system has been designed to indicate the best evacuation direction for applications like the Large Hadron Collider (LHC) tunnel. The design includes constraints for redundancy required by safety systems and for components selection by radiation effects. Most of the literature for radiation effects on LEDs concern digital communications systems, although some recent reports do exist for visible spectrum power LEDs and the reduction in light output versus dose is coherent with the results presented in this paper. Prototype lighting units were irradiated in CERN’s CHARM facility up to a Total Integrated Dose (TID) of 870 Gy and no failures were observed. This paper describes the basic design, presents field tests and the effects of radiation on the LEDs luminance.

  4. NSTX-U Digital Coil Protection System Software Detailed Design

    None

    2014-06-01

    The National Spherical Torus Experiment (NSTX) currently uses a collection of analog signal processing solutions for coil protection. Part of the NSTX Upgrade (NSTX-U) entails replacing these analog systems with a software solution running on a conventional computing platform. The new Digital Coil Protection System (DCPS) will replace the old systems entirely, while also providing an extensible framework that allows adding new functionality as desired.

  5. Design of digital voice storage and playback system

    Tang, Chao

    2018-03-01

    Based on STC89C52 chip, this paper presents a single chip microcomputer minimum system, which is used to realize the logic control of digital speech storage and playback system. Compared with the traditional tape voice recording system, the system has advantages of small size, low power consumption, The effective solution of traditional voice recording system is limited in the use of electronic and information processing.

  6. Digital logic circuit design with ALTERA Quartus II

    Lee, Seung Ho

    2009-09-01

    This book consists 31 chapters about digital logic circuit with ALTERA Quartus II. It includes the introduction of ALTERA Quartus II, ALTERA Quartus II schematic editor, ALTERA Quartus II compiler, ALTERA Quartus II simulator, ALTERA Quartus II timing analyzer, how to use HBE-COMBO II training and HBE-COMBO II training kit with schematic editor, VHDL grammar and practice of ALTERA Quartus II and HBE-COMBO II training kit with VHDL.

  7. Scheduling and Topology Design in Networks with Directional Antennas

    2017-05-19

    Scheduling and Topology Design in Networks with Directional Antennas Thomas Stahlbuhk, Nathaniel M. Jones, Brooke Shrader Lincoln Laboratory...controllers must choose which pairs of nodes should communicate in order to establish a topology over which traffic can be sent. Additionally...interacting effects of topology design and transmission scheduling in wireless networks, in particular focusing on networks where nodes are divided into

  8. 77 FR 3585 - Airworthiness Directives; Cirrus Design Corporation Airplanes

    2012-01-25

    ... Airworthiness Directives; Cirrus Design Corporation Airplanes AGENCY: Federal Aviation Administration (FAA), DOT... Corporation (Cirrus) Model SR22T airplanes. This AD was prompted by reports of partial loss of engine power.... ADDRESSES: For service information identified in this AD, contact Cirrus Design Corporation, 4515 Taylor...

  9. Establishment of a Digital Knowledge Conversion Architecture Design Learning with High User Acceptance

    Wu, Yun-Wu; Weng, Apollo; Weng, Kuo-Hua

    2017-01-01

    The purpose of this study is to design a knowledge conversion and management digital learning system for architecture design learning, helping students to share, extract, use and create their design knowledge through web-based interactive activities based on socialization, internalization, combination and externalization process in addition to…

  10. A Web-Based Visualization and Animation Platform for Digital Logic Design

    Shoufan, Abdulhadi; Lu, Zheng; Huss, Sorin A.

    2015-01-01

    This paper presents a web-based education platform for the visualization and animation of the digital logic design process. This includes the design of combinatorial circuits using logic gates, multiplexers, decoders, and look-up-tables as well as the design of finite state machines. Various configurations of finite state machines can be selected…

  11. Managing Increasing Complexity in Undergraduate Digital Media Design Education: The Impact and Benefits of Multidisciplinary Collaboration

    Fleischmann, Katja; Daniel, Ryan

    2013-01-01

    Increasing complexity is one of the most pertinent issues when discussing the role and future of design, designers and their education. The evolving nature of digital media technology has resulted in a profession in a state of flux with increasingly complex communication and design problems. The ability to collaborate and interact with other…

  12. Developing digital technologies for university mathematics by applying participatory design methods

    Triantafyllou, Eva; Timcenko, Olga

    2013-01-01

    This paper presents our research efforts to develop digital technologies for undergraduate university mathematics. We employ participatory design methods in order to involve teachers and students in the design of such technologies. The results of the first round of our design are included...

  13. Efficient design of multiplier-less digital channelizers using recombination non-uniform filter banks

    Shaeen Kalathil

    2018-01-01

    Full Text Available A novel approach for the efficient realization of digital channelizers in software defined radios using recombination filter banks is proposed in this paper. Digital channelizer is the core of software defined radio. Computationally efficient design supporting multiple channels with different bandwidths and low complexity are inevitable requirements for the digital channelizers. Recombination filter banks method is used to obtain non-uniform filter banks with rational sampling factors, using a two stage structure. It consists of a uniform filter bank and trans-multiplexer. In this work, the uniform filter bank and trans-multiplexer are designed using cosine modulated filter banks. The prototype filter design is made simple, efficient and fast, using window method. The multiplier-less realization of recombination filter banks in the canonic signed digit space using nature inspired optimization algorithms, results in reduced implementation complexity.

  14. Design and Optimization of Fast Switching Valves for Large Scale Digital Hydraulic Motors

    Roemer, Daniel Beck

    The present thesis is on the design, analysis and optimization of fast switching valves for digital hydraulic motors with high power ratings. The need for such high power motors origins in the potential use of hydrostatic transmissions in wind turbine drive trains, as digital hydraulic machines...... have been shown to improve the overall efficiency and efficient operation range compared to traditional hydraulic machines. Digital hydraulic motors uses electronically controlled independent seat valves connected to the pressure chambers, which must be fast acting and exhibit low pressure losses...... to enable efficient operation. These valves are complex components to design, as multiple design aspects are present in these integrated valve units, with conflicting objectives and interdependencies. A preliminary study on a small scale single-cylinder digital hydraulic pump has initially been conducted...

  15. Regulating Direct-to-Consumer Advertising of Prescription Drugs in the Digital Age

    Shannon Gibson

    2014-07-01

    Full Text Available The increasing prominence of new Internet and social media technologies and their growing importance as a source of health information are pushing the pharmaceutical industry towards digital channels. This paper explores the potential impacts of the pharmaceutical industry’s increasing interest in online marketing and considers how the existing regulatory framework in Canada translates into the social media sphere. Direct-to-consumer advertising (DTCA of prescription drugs is prohibited in Canada, as it is in most industrialized countries. Although Health Canada has reaffirmed that the existing DTCA regulations apply to new Internet and social media technologies, new dynamics such as user-generated content, consumer propagation, and targeted marketing make applying the existing regulations an uncertain process. Moreover, certain problems often associated with DTCA may be exacerbated in the social media context. Finally, there is skepticism around whether government regulators have the resources or political will to effectively monitor new digital media. As such, this paper considers not only the role of direct government regulation in monitoring and enforcing the regulation of DTCA, but also the role of third party oversight and industry self-regulation—both of which may play an important role in filling the gaps in the regulation of the Internet and social media.

  16. Note: A new method for directly reducing the sampling jitter noise of the digital phasemeter

    Liang, Yu-Rong

    2018-03-01

    The sampling jitter noise is one non-negligible noise source of the digital phasemeter used for space gravitational wave detection missions. This note provides a new method for directly reducing the sampling jitter noise of the digital phasemeter, by adding a dedicated signal of which the frequency, amplitude, and initial phase should be pre-set. In contrast to the phase correction using the pilot-tone in the work of Burnett, Gerberding et al., Liang et al., Ales et al., Gerberding et al., and Ware et al. [M.Sc. thesis, Luleå University of Technology, 2010; Classical Quantum Gravity 30, 235029 (2013); Rev. Sci. Instrum. 86, 016106 (2015); Rev. Sci. Instrum. 86, 084502 (2015); Rev. Sci. Instrum. 86, 074501 (2015); and Proceedings of the Earth Science Technology Conference (NASA, USA, 2006)], the new method is intrinsically additive noise suppression. The experiment results validate that the new method directly reduces the sampling jitter noise without data post-processing and provides the same phase measurement noise level (10-6 rad/Hz1/2 at 0.1 Hz) as the pilot-tone correction.

  17. Design and simulation of the direct drive servo system

    Ren, Changzhi; Liu, Zhao; Song, Libin; Yi, Qiang; Chen, Ken; Zhang, Zhenchao

    2010-07-01

    As direct drive technology is finding their way into telescope drive designs for its many advantages, it would push to more reliable and cheaper solutions for future telescope complex motion system. However, the telescope drive system based on the direct drive technology is one high integrated electromechanical system, which one complex electromechanical design method is adopted to improve the efficiency, reliability and quality of the system during the design and manufacture circle. The telescope is one ultra-exact, ultra-speed, high precision and huge inertial instrument, which the direct torque motor adopted by the telescope drive system is different from traditional motor. This paper explores the design process and some simulation results are discussed.

  18. Design and testing of a 750MHz CW-EPR digital console for small animal imaging.

    Sato-Akaba, Hideo; Emoto, Miho C; Hirata, Hiroshi; Fujii, Hirotada G

    2017-11-01

    This paper describes the development of a digital console for three-dimensional (3D) continuous wave electron paramagnetic resonance (CW-EPR) imaging of a small animal to improve the signal-to-noise ratio and lower the cost of the EPR imaging system. A RF generation board, an RF acquisition board and a digital signal processing (DSP) & control board were built for the digital EPR detection. Direct sampling of the reflected RF signal from a resonator (approximately 750MHz), which contains the EPR signal, was carried out using a band-pass subsampling method. A direct automatic control system to reduce the reflection from the resonator was proposed and implemented in the digital EPR detection scheme. All DSP tasks were carried out in field programmable gate array ICs. In vivo 3D imaging of nitroxyl radicals in a mouse's head was successfully performed. Copyright © 2017 Elsevier Inc. All rights reserved.

  19. Design and testing of a 750 MHz CW-EPR digital console for small animal imaging

    Sato-Akaba, Hideo; Emoto, Miho C.; Hirata, Hiroshi; Fujii, Hirotada G.

    2017-11-01

    This paper describes the development of a digital console for three-dimensional (3D) continuous wave electron paramagnetic resonance (CW-EPR) imaging of a small animal to improve the signal-to-noise ratio and lower the cost of the EPR imaging system. A RF generation board, an RF acquisition board and a digital signal processing (DSP) & control board were built for the digital EPR detection. Direct sampling of the reflected RF signal from a resonator (approximately 750 MHz), which contains the EPR signal, was carried out using a band-pass subsampling method. A direct automatic control system to reduce the reflection from the resonator was proposed and implemented in the digital EPR detection scheme. All DSP tasks were carried out in field programmable gate array ICs. In vivo 3D imaging of nitroxyl radicals in a mouse's head was successfully performed.

  20. Wireless receiver architectures and design antennas, RF, synthesizers, mixed signal, and digital signal processing

    Rouphael, Tony J

    2014-01-01

    Wireless Receiver Architectures and Design presents the various designs and architectures of wireless receivers in the context of modern multi-mode and multi-standard devices. This one-stop reference and guide to designing low-cost low-power multi-mode, multi-standard receivers treats analog and digital signal processing simultaneously, with equal detail given to the chosen architecture and modulating waveform. It provides a complete understanding of the receiver's analog front end and the digital backend, and how each affects the other. The book explains the design process in great detail, s

  1. All-Pole Recursive Digital Filters Design Based on Ultraspherical Polynomials

    N. Stojanovic; N. Stamenkovic; V. Stojanovic

    2014-01-01

    A simple method for approximation of all-pole recursive digital filters, directly in digital domain, is described. Transfer function of these filters, referred to as Ultraspherical filters, is controlled by order of the Ultraspherical polynomial, nu. Parameter nu, restricted to be a nonnegative real number (nu ≥ 0), controls ripple peaks in the passband of the magnitude response and enables a trade-off between the passband loss and the group delay response of the resulting filter. Chebyshev f...

  2. Design of a digital PAD based on I/Q demodulation principle

    Geng Zheqiao; Cui Yanyan; Hou Mi; Pei Guoxi

    2005-01-01

    Conventional analog I/Q demodulator suffers from phase and amplitude imbalance and DC offset, which cause big error into the measurement. A digital PAD is designed. Based on I/Q demodulation principle, using digital algorithms, such as digital filter and Hilbert transform, the conventional measurement error can basically be removed. Measuremental results show that the digital PAD has a maximum phase error of ±0.5 degree and a resolution of 0.2 degree. Its temperature coefficient is -0.1 degree/degree C. Its dynamic ranges for phase-measurement and amplitude-measurement are -1825 dBm and -2020 dBm, respectively. The digital PAD can meet the need of the BEPC II phasing system. (authors)

  3. Web Interface Design Principles for Adults’ Self-Directed Learning

    Mehmet FIRAT

    2016-10-01

    Full Text Available One of the most important features which e-learning tools and environments must possess within the scope of lifelong learning is self-directed learning, which can be considered as a form of self-learning. The aim of this study was to determine, based on the views and recommendations of experts, interface design principles for the development of educational web interfaces that will support the self-directed learning of adults. This descriptive study was conducted with the contribution of 12 academicians specializing in interface design and self-directed learning. Within the scope of the study, new interfaces features were identified based on an evaluation of the literature on interface designs for self-directed learning, and the views of subject experts. Based on the study results, it was determined that interface designs supporting self-directed learning must possess five basic features, which include being user-directed, ensuring variety, being supported by learning analytics, being motivational, and being sharing-oriented.

  4. Optimization and Implementation of Scaling-Free CORDIC-Based Direct Digital Frequency Synthesizer for Body Care Area Network Systems

    Ying-Shen Juang

    2012-01-01

    Full Text Available Coordinate rotation digital computer (CORDIC is an efficient algorithm for computations of trigonometric functions. Scaling-free-CORDIC is one of the famous CORDIC implementations with advantages of speed and area. In this paper, a novel direct digital frequency synthesizer (DDFS based on scaling-free CORDIC is presented. The proposed multiplier-less architecture with small ROM and pipeline data path has advantages of high data rate, high precision, high performance, and less hardware cost. The design procedure with performance and hardware analysis for optimization has also been given. It is verified by Matlab simulations and then implemented with field programmable gate array (FPGA by Verilog. The spurious-free dynamic range (SFDR is over 86.85 dBc, and the signal-to-noise ratio (SNR is more than 81.12 dB. The scaling-free CORDIC-based architecture is suitable for VLSI implementations for the DDFS applications in terms of hardware cost, power consumption, SNR, and SFDR. The proposed DDFS is very suitable for medical instruments and body care area network systems.

  5. Data Collection for Mental Health Studies Through Digital Platforms: Requirements and Design of a Prototype.

    Aledavood, Talayeh; Triana Hoyos, Ana Maria; Alakörkkö, Tuomas; Kaski, Kimmo; Saramäki, Jari; Isometsä, Erkki; Darst, Richard K

    2017-06-09

    Mental and behavioral disorders are the main cause of disability worldwide. However, their diagnosis is challenging due to a lack of reliable biomarkers; current detection is based on structured clinical interviews which can be biased by the patient's recall ability, affective state, changing in temporal frames, etc. While digital platforms have been introduced as a possible solution to this complex problem, there is little evidence on the extent of usability and usefulness of these platforms. Therefore, more studies where digital data is collected in larger scales are needed to collect scientific evidence on the capacities of these platforms. Most of the existing platforms for digital psychiatry studies are designed as monolithic systems for a certain type of study; publications from these studies focus on their results, rather than the design features of the data collection platform. Inevitably, more tools and platforms will emerge in the near future to fulfill the need for digital data collection for psychiatry. Currently little knowledge is available from existing digital platforms for future data collection platforms to build upon. The objective of this work was to identify the most important features for designing a digital platform for data collection for mental health studies, and to demonstrate a prototype platform that we built based on these design features. We worked closely in a multidisciplinary collaboration with psychiatrists, software developers, and data scientists and identified the key features which could guarantee short-term and long-term stability and usefulness of the platform from the designing stage to data collection and analysis of collected data. The key design features that we identified were flexibility of access control, flexibility of data sources, and first-order privacy protection. We also designed the prototype platform Non-Intrusive Individual Monitoring Architecture (Niima), where we implemented these key design features. We

  6. Design and evaluation of an architecture for a digital signal processor for instrumentation applications

    Fellman, Ronald D.; Kaneshiro, Ronald T.; Konstantinides, Konstantinos

    1990-03-01

    The authors present the design and evaluation of an architecture for a monolithic, programmable, floating-point digital signal processor (DSP) for instrumentation applications. An investigation of the most commonly used algorithms in instrumentation led to a design that satisfies the requirements for high computational and I/O (input/output) throughput. In the arithmetic unit, a 16- x 16-bit multiplier and a 32-bit accumulator provide the capability for single-cycle multiply/accumulate operations, and three format adjusters automatically adjust the data format for increased accuracy and dynamic range. An on-chip I/O unit is capable of handling data block transfers through a direct memory access port and real-time data streams through a pair of parallel I/O ports. I/O operations and program execution are performed in parallel. In addition, the processor includes two data memories with independent addressing units, a microsequencer with instruction RAM, and multiplexers for internal data redirection. The authors also present the structure and implementation of a design environment suitable for the algorithmic, behavioral, and timing simulation of a complete DSP system. Various benchmarking results are reported.

  7. [Application of digital design of orthodontic-prosthodontic multidisciplinary treatment plan in esthetic rehabilitation of anterior teeth].

    Liu, Y S; Li, Z; Zhao, Y J; Ye, H Q; Zhou, Y Q; Hu, W J; Liu, Y S; Xun, C L; Zhou, Y S

    2018-02-18

    To develop a digital workflow of orthodontic-prosthodontic multidisciplinary treatment plan which can be applied in complicated anterior teeth esthetic rehabilitation, in order to enhance the efficiency of communication between dentists and patients, and improve the predictability of treatment outcome. Twenty patients with the potential needs of orthodontic-prosthodontic multidisciplinary treatment to solve their complicated esthetic problems in anterior teeth were recruited in this study. Digital models of patients' both dental arches and soft tissues were captured using intra oral scanner. Direct prosthodontic (DP) treatment plan and orthodontic-prosthodontic (OP) treatment plan were carried out for each patient. For DP treatment plans, digital wax-up models were directly designed on original digital models using prosthodontic design system. For OP treatment plans, virtual-setups were performed using orthodontic analyze system according to orthodontic and esthetic criteria and imported to prosthodontic design system to finalize the digital wax-up models. These two treatment plans were shown to the patients and demonstrated elaborately. Each patient rated two treatment plans using visual analogue scales and the medians of scores of two treatment plans were analyzed using signed Wilcoxon test. Having taken into consideration various related factors, including time, costs of treatment, each patient chose a specific treatment plan. For the patients chose DP treatment plans, digital wax-up models were exported and printed into resin diagnostic models which would be utilized in the prosthodontic treatment process. For the patients chose OP treatment plans, virtual-setups were used to fabricate aligners or indirect bonding templates and digital wax-up models were also exported and printed into resin diagnostic models for prosthodontic treatment after orthodontic treatment completed. The medians of scores of DP treatment plan and OP treatment plan were calculated and

  8. Design Tool for 5-20 MW Direct Drive Generators

    Leban, Krisztina Monika; Ritchie, Ewen; Argeseanu, Alin

    2014-01-01

    This paper reports on a machine design tool for large (5-10MW) direct drive electrical generator. The aim of the work is to construct a flexible calculation tool that enables the analysis of different ideas and concepts for generator design. The tool is intended for engineers that are involved...... in the design of wind turbine systems. The design tool comprises calculation modules that are kept as independent as possible from each other so that new machine geometries and types can be modelled by reusing, recombining and modifying the different modules. Choice of the most suitable candidates...

  9. Adobe InDesign CS6 digital classroom

    Smith, Christopher

    2012-01-01

    Expert book-and-video package helps you conquer Adobe InDesign CS6 Whether you want to create sophisticated page layouts for print or electronic books or produce dazzling brochures and other publications, chances are Adobe InDesign is the design and page layout tool you'll call upon. Now you can enhance your creativity and discover all the ways to use Adobe InDesign with this book-and-DVD training package. Thirteen self-paced lessons teach you how to design, produce, and develop streamlined workflows for page layout. Each lesson is accompanied by a video tutorial that clearly demonstrates

  10. Digital PI-PD controller design for arbitrary order systems: Dominant pole placement approach.

    Dincel, Emre; Söylemez, Mehmet Turan

    2018-05-02

    In this paper, a digital PI-PD controller design method is proposed for arbitrary order systems with or without time-delay to achieve desired transient response in the closed-loop via dominant pole placement approach. The digital PI-PD controller design problem is solved by converting the original problem to the digital PID controller design problem. Firstly, parametrization of the digital PID controllers which assign dominant poles to desired location is done. After that the subset of digital PID controller parameters in which the remaining poles are located away from the dominant pole pair is found via Chebyshev polynomials. The obtained PID controller parameters are then transformed into the PI-PD controller parameters by considering the closed-loop controller zero and the design is completed. Success of the proposed design method is firstly demonstrated on an example transfer function and compared with the well-known PID controller methods from the literature through simulations. After that the design method is implemented on the fan and plate laboratory system in a real environment. Copyright © 2018 ISA. Published by Elsevier Ltd. All rights reserved.

  11. Designing learning apparatus to promote twelfth grade students’ understanding of digital technology concept: A preliminary studies

    Marlius; Kaniawati, I.; Feranie, S.

    2018-05-01

    A preliminary learning design using relay to promote twelfth grade student’s understanding of logic gates concept is implemented to see how well it’s to adopted by six high school students, three male students and three female students of twelfth grade. This learning design is considered for next learning of digital technology concept i.e. data digital transmition and analog. This work is a preliminary study to design the learning for large class. So far just a few researches designing learning design related to digital technology with relay. It may due to this concept inserted in Indonesian twelfth grade curriculum recently. This analysis is focus on student difficulties trough video analysis to learn the concept. Based on our analysis, the recommended thing for redesigning learning is: students understand first about symbols and electrical circuits; the Student Worksheet is made in more detail on the assembly steps to the project board; mark with symbols at points in certain places in the circuit for easy assembly; assembly using relays by students is enough until is the NOT’s logic gates and the others that have been assembled so that effective time. The design of learning using relays can make the relay a liaison between the abstract on the digital with the real thing of it, especially in the circuit of symbols and real circuits. Besides it is expected to also enrich the ability of teachers in classroom learning about digital technology.

  12. Exploratory Study of Rural Physicians' Self-Directed Learning Experiences in a Digital Age.

    Curran, Vernon; Fleet, Lisa; Simmons, Karla; Ravalia, Mohamed; Snow, Pamela

    2016-01-01

    The nature and characteristics of self-directed learning (SDL) by physicians has been transformed with the growth in digital, social, and mobile technologies (DSMTs). Although these technologies present opportunities for greater "just-in-time" information seeking, there are issues for ensuring effective and efficient usage to compliment one's repertoire for continuous learning. The purpose of this study was to explore the SDL experiences of rural physicians and the potential of DSMTs for supporting their continuing professional development (CPD). Semistructured interviews were conducted with a purposive sample of rural physicians. Interview data were transcribed verbatim and analyzed using NVivo analytical software and thematic analysis. Fourteen (N = 14) interviews were conducted and key thematic categories that emerged included key triggers, methods of undertaking SDL, barriers, and supports. Methods and resources for undertaking SDL have evolved considerably, and rural physicians report greater usage of mobile phones, tablets, and laptop computers for updating their knowledge and skills and in responding to patient questions/problems. Mobile technologies, and some social media, can serve as "triggers" in instigating SDL and a greater usage of DSMTs, particularly at "point of care," may result in higher levels of SDL. Social media is met with some scrutiny and ambivalence, mainly because of the "credibility" of information and risks associated with digital professionalism. DSMTs are growing in popularity as a key resource to support SDL for rural physicians. Mobile technologies are enabling greater "point-of-care" learning and more efficient information seeking. Effective use of DSMTs for SDL has implications for enhancing just-in-time learning and quality of care. Increasing use of DSMTs and their new effect on SDL raises the need for reflection on conceptualizations of the SDL process. The "digital age" has implications for our CPD credit systems and the roles

  13. Intelligent Digitized Design Systems for the Management of Design Knowledge Related to Nuclear R&D Institutes

    Zheng, M.; Minglu, W.

    2016-01-01

    Full text: Nuclear R&D is highly knowledge-intensive. With the rapid advent and development of modern information technology, knowledge management in nuclear industry has been provided with new approaches and possibilities. This article introduces a framework of intelligent digitized design system in nuclear R&D phase and finds answer to knowledge application, internal process optimization, experience feedback and further innovation. This framework utilizing digitalization and informatization finds a way to incorporate the process of the “Socialization, Externalization, Combination, Internalization” (SECI) model which include intelligent design process, integrated design software, smart verification and validation simulation platform, experiment data management platform, online monitoring platform and digital twin nuclear power plant, etc. The following case study gives a clear picture of what and how knowledge management has been performed under this framework. Furthermore, important lessons have been summarized. (author

  14. Design of digital load torque observer in hybrid electric vehicle

    Sun, Yukun; Zhang, Haoming; Wang, Yinghai

    2008-12-01

    In hybrid electric vehicle, engine begain to work only when motor was in high speed in order to decrease tail gas emission. However, permanent magnet motor was sensitive to its load, adding engine to the system always made its speed drop sharply, which caused engine to work in low efficiency again and produced much more environment pollution. Dynamic load torque model of permanent magnet synchronous motor is established on the basic of motor mechanical equation and permanent magnet synchronous motor vector control theory, Full- digital load torque observer and compensation control system is made based on TMS320F2407A. Experiment results prove load torque observer and compensation control system can detect and compensate torque disturbing effectively, which can solve load torque disturbing and decrease gas pollution of hybrid electric vehicle.

  15. Cyber and physical equipment digital control system in Industry 4.0 item designing company

    Gurjanov, A. V.; Zakoldaev, D. A.; Shukalov, A. V.; Zharinov, I. O.

    2018-05-01

    The problem of organization of digital control of the item designing company equipped with cyber and physical systems is being studied. A scheme of cyber and physical systems and personnel interaction in the Industry 4.0 smart factory company is presented. A scheme of assembly units transportation in the Industry 4.0 smart factory company is provided. A scheme of digital control system in the Industry 4.0 smart factory company is given.

  16. Comparison of the diagnostic accuracy of direct digital radiography system, filtered images, and subtraction radiography

    Wilton Mitsunari Takeshita

    2013-01-01

    Full Text Available Background: To compare the diagnostic accuracy of three different imaging systems: Direct digital radiography system (DDR-CMOS, four types of filtered images, and a priori and a posteriori registration of digital subtraction radiography (DSR in the diagnosis of proximal defects. Materials and Methods: The teeth were arranged in pairs in 10 blocks of vinyl polysiloxane, and proximal defects were performed with drills of 0.25, 0.5, and 1 mm diameter. Kodak RVG 6100 sensor was used to capture the images. A posteriori DSR registrations were done with Regeemy 0.2.43 and subtraction with Image Tool 3.0. Filtered images were obtained with Kodak Dental Imaging 6.1 software. Images (n = 360 were evaluated by three raters, all experts in dental radiology. Results: Sensitivity and specificity of the area under the receiver operator characteristic (ROC curve (Az were higher for DSR images with all three drills (Az = 0.896, 0.979, and 1.000 for drills 0.25, 0.5, and 1 mm, respectively. The highest values were found for 1-mm drills and the lowest for 0.25-mm drills, with negative filter having the lowest values of all (Az = 0.631. Conclusion: The best method of diagnosis was by using a DSR. The negative filter obtained the worst results. Larger drills showed the highest sensitivity and specificity values of the area under the ROC curve.

  17. Design Tool for Direct Drive Wind Turbine Generators

    Leban, Krisztina Monika

    . A comparison of the selected machine types in view of up-scaling to 20 [MW] was performed. As an example fitness criterion, the use of active materials for the generators was considered. Based on this, suggestions for 20 [MW] generators were made. The results are discussed and future work, directions......The current work offers a comparison of the proposed machine geometries for 6 [MW] direct drive wind generator candidates with the prospective of up scaling to 20MW. The suggestions are based on a design tool especially built for this investigation. The in-built flexibility of the design tool gives...

  18. The modular design method for digital control systems in Japanese BWRs

    Kondoh, Y.; Motomura, A.

    1998-01-01

    Digital technology is being applied to control systems in nuclear power plants. Especially in Japanese BWRs, control systems are being digitized both in constructing plant and in retrofit of operating plants. Digital technology has many advantages compared with analog technology. However, its high performance and flexibility may result in too complicated software structure, which will cause long design time and long testing time and increase cost. In introduction of digital technology, it is most important to restrict unnecessary flexibility of software. The function of control systems can be divided in standard part and variable part. Standard function may be common to every plant while variable function should be designed for each plant. Even in current design, standard design is preserved to be reused in next application. However, this design approach is not always effective because standard function may be changed by customer and nothing is considered for variable part even if it is large. To keep reliability and reduce cost by software reuse, Toshiba adopts modular design of control software, where standard part is designed as a set of standard functional modules and variable function is designed as a complex of standard functional modules and plant unique modules. Toshiba firstly applied modular design method to fuel handling machine control system. In this application the design work has been reduced to 30 percent by reusing of functional module which was first developed in former applications. This remarkable reduction of design work has enhanced reliability with less cost. In addition, software, has been produced and tested according to the functional module. These qualified software modules will be applied to next system and will realize highest reliability and least cost. Toshiba is now planning the application of this modular design method for every digital control system. (author)

  19. Teachers’ Pedagogic Design of Digital Interactive Whiteboard Materials in the UK Secondary School

    Carey Jewitt

    2008-03-01

    Full Text Available Teachers have always made texts for use in the classroom. The wide spread introduction of Interactive whiteboard (IWB technology into UK classrooms, and the screen more generally, makes the multimodal resources of color, image, dynamic movement, and sound newly available for pedagogic design in newly connectable ways. These facilities present teachers with new questions about how to design and use teaching materials, new possibilites and constraints. This presentation will examine teachers' design of digital multimodal resources for IWBs and the influence of prevalent policy discourses of interactivity, multimodality and fast pace influence on teacher’s digital materials for the IWB.

  20. The use of the digital smile design concept as an auxiliary tool in periodontal plastic surgery.

    Santos, Felipe Rychuv; Kamarowski, Stephanie Felice; Lopez, Camilo Andres Villabona; Storrer, Carmen Lucia Mueller; Neto, Alexandre Teixeira; Deliberador, Tatiana Miranda

    2017-01-01

    Periodontal surgery associated with prior waxing, mock-up, and the use of digital tools to design the smile is the current trend of reverse planning in periodontal plastic surgery. The objective of this study is to report a surgical resolution of the gummy smile using a prior esthetic design with the use of digital tools. A digital smile design and mock-up were used for performing gingival recontouring surgery. The relationship between the facial and dental measures and the incisal plane with the horizontal facial plane of reference were evaluated. The relative dental height x width was measured, and the dental contour drawing was inserted. Complementary lines are drawn such as the gingival zenith, joining lines of the gingival and incisal battlements. The periodontal esthetic was improved according to the established design digital smile pattern. These results demonstrate the importance of surgical techniques and are well accepted by patients and are easy to perform for the professional. When properly planned, they provide the desired expectations. Periodontal Surgical procedures associated with the design digital smile facilitate the communication between the patient and the professional. It is, therefore, essential to demonstrate the reverse planning of the smile and periodontal parameters with approval by the patient to solve the esthetic problem.

  1. Collective interaction by design collective controllers for social navigation on digital photos

    Petersen, Marianne Graves; Krogh, Peter; Mortensen, Morten Boye

    2010-01-01

    trial use serves to refine the collective interaction model and identify qualities and shortcommings of collective interaction applications. In this way we wish to point to a design space, which can lead to new interaction techniques and -designs supporting shared social experiences around digital...

  2. Pre-Service Physics Teachers' Views on Designing and Developing Physics Digital Stories

    Kocakaya, Serhat; Kotluk, Nihat; Karakoyun, Ferit

    2016-01-01

    The aim of this study is to determine the pre-service physics teachers' views on the effect of designing and developing physics digital stories (DST) on improving their 21st century skills. The study is a qualitative research carried out with 13 pre-service physics teachers, who participated in the course of designing and developing DST, during 6…

  3. Lecture note on digital circuit design for high energy physics experiment

    Ikeda, Hirokazu.

    1993-08-01

    This lecture gives basic ideas and practice of the digital circuit design for high energy physics experiment. The lecture has a special emphasis on a simulation study with a hardware description language. The student could complete a design of a simple RISC based computer after finishing this course. (author)

  4. Design of active controls for the NASA F-8 digital fly-by-wire airplane

    Gera, J.

    1976-01-01

    The design of a set of control laws for the NASA F-8 digital fly by wire research airplane is described. These control laws implement several active controls functions: maneuver load control, ride smoothing and departure boundary limiting. The criteria and methods which were used in the design of the control laws are also included. Results of linear analyses and nonlinear simulation are summarized.

  5. Designing a Deeply Digital Science Curriculum: Supporting Teacher Learning and Implementation with Organizing Technologies

    Leary, Heather; Severance, Samuel; Penuel, William R.; Quigley, David; Sumner, Tamara; Devaul, Holly

    2016-01-01

    This paper examines the impacts of technology (e.g., Chromebooks, Google Drive) on teacher learning and student activity in the development and implementation of a deeply digital high school biology unit. Using design-based implementation research, teachers co-designed with researchers and curriculum specialists a student-centered unit aligned to…

  6. An ultra-high-speed direct digital frequency synthesizer implemented in GaAs HBT technology

    Chen Gaopeng; Wu Danyu; Jin Zhi; Liu Xinyu

    2010-01-01

    This paper presents a 10-GHz 8-bit direct digital synthesizer (DDS) microwave monolithic integrated circuit implemented in 1 μm GaAs HBT technology. The DDS takes a double-edge-trigger (DET) 8-stage pipeline accumulator with sine-weighted DAC-based ROM-less architecture, which can maximize the utilization ratio of the GaAs HBT's high-speed potential. With an output frequency up to 5 GHz, the DDS gives an average spurious free dynamic range of 23.24 dBc through the first Nyquist band, and consumes 2.4 W of DC power from a single -4.6 V DC supply. Using 1651 GaAs HBT transistors, the total area of the DDS chip is 2.4 x 2.0 mm 2 . (semiconductor integrated circuits)

  7. Fingerprint Image Enhancement Based on Second Directional Derivative of the Digital Image

    Onnia Vesa

    2002-01-01

    Full Text Available This paper presents a novel approach of fingerprint image enhancement that relies on detecting the fingerprint ridges as image regions where the second directional derivative of the digital image is positive. A facet model is used in order to approximate the derivatives at each image pixel based on the intensity values of pixels located in a certain neighborhood. We note that the size of this neighborhood has a critical role in achieving accurate enhancement results. Using neighborhoods of various sizes, the proposed algorithm determines several candidate binary representations of the input fingerprint pattern. Subsequently, an output binary ridge-map image is created by selecting image zones, from the available binary image candidates, according to a MAP selection rule. Two public domain collections of fingerprint images are used in order to objectively assess the performance of the proposed fingerprint image enhancement approach.

  8. Designing a Programmatic Digital Learning Environment: Lessons from Prototyping

    Gal, Diane; Lewis, Mark

    2018-01-01

    Promoted as a way to enhance learning and improve efficiencies, the steady rise of technology adoption across higher education has created both new opportunities and new challenges. Borrowing principles of design thinking and related user- or learner-centered design practices, this descriptive case study offers an example of how institutions of…

  9. Designed and Accidental Humor in the Smart Digital Wild

    Nijholt, Anton; Ruiz Miyares, L.

    Humor can be designed and canned, for example as it appears in videogames, sitcoms or amusement parks. We often have humor professionals that have responsibility for this inclusion of humor. Humor can be designed for a particular occasion, for example in an April prank. However, in real life we

  10. Digital selective fabrication of micro/nano-composite structured TiO2 nanorod arrays by laser direct writing

    Jiang, Wei; He, Xiaoning; Liu, Hongzhong; Yin, Lei; Shi, Yongsheng; Ding, Yucheng

    2014-11-01

    In this article, we report on the digital selective fabrication of micro/nano-composite structured TiO2 nanorod arrays by laser direct writing. The pattern of TiO2 nanorod arrays can be easily designed and fabricated by laser scanning technology integrated with a computer-aided design system, which allows a high degree of freedom corresponding to the various pattern design demands. The approach basically involves the hydrothermal growth of TiO2 nanorod arrays on a transparent conductive substrate, the micropattern of TiO2 nanorod arrays and surface fluorination treatment. With these micro/nano-composite TiO2 nanorod array based films, we have demonstrated superhydrophilic patterned TiO2 nanorod arrays with rapid water spreading ability and superhydrophobic patterned TiO2 nanorod arrays with an excellent droplet bouncing effect and a good self-cleaning performance. The dynamic behaviours of the water droplets observed on the patterned TiO2 nanorod arrays were demonstrated by experiments and simulated by a finite element method. The approaches we will show are expected to provide potential applications in fields such as self-cleaning, surface protection, anticrawling and microfluidic manipulation.

  11. SCAN- a maintenance-free flowrate meter with direct digital read-out for computerised control applications in radiochemical plants

    Shah, B V; Siddiqui, I A; Theyyunni, T K [Process Engineering and Systems Division, Bhabha Atomic Research Centre, Mumbai (India)

    1994-06-01

    In radiochemical plants, the choice of flowrate sensor is subject to stringent requirements of fail-safe design and freedom from maintenance. The SCAN remote digital direct indicating flowrate meter described in this paper was developed to meet the requirements of flowrate and transmitting it to the control room, and to a computerised control system. SCAN is designed on the principle that flowrate through an orifice is a function of the head of liquid acting upon it. SCAN consists of a small chamber which receives the flow, and discharges it through an orifice located in bottom. The level of liquid in the pot represents the flowrate of the input stream. SCAN has been developed into an accurate, rugged and practical device by refinements in the design of internals, and by introducing a special end-section which makes the calibration insensitive to location. An important feature of SCAN is that it is passive, maintenance free, fail-safe device and contains no moving parts. There is no liquid hold up in the SCAN when idle, which is a desirable feature for the radiochemical plant environment. (author). 3 figs., 2 tabs.

  12. A Comparative Study on Diagnostic Accuracy of Colour Coded Digital Images, Direct Digital Images and Conventional Radiographs for Periapical Lesions – An In Vitro Study

    Mubeen; K.R., Vijayalakshmi; Bhuyan, Sanat Kumar; Panigrahi, Rajat G; Priyadarshini, Smita R; Misra, Satyaranjan; Singh, Chandravir

    2014-01-01

    Objectives: The identification and radiographic interpretation of periapical bone lesions is important for accurate diagnosis and treatment. The present study was undertaken to study the feasibility and diagnostic accuracy of colour coded digital radiographs in terms of presence and size of lesion and to compare the diagnostic accuracy of colour coded digital images with direct digital images and conventional radiographs for assessing periapical lesions. Materials and Methods: Sixty human dry cadaver hemimandibles were obtained and periapical lesions were created in first and second premolar teeth at the junction of cancellous and cortical bone using a micromotor handpiece and carbide burs of sizes 2, 4 and 6. After each successive use of round burs, a conventional, RVG and colour coded image was taken for each specimen. All the images were evaluated by three observers. The diagnostic accuracy for each bur and image mode was calculated statistically. Results: Our results showed good interobserver (kappa > 0.61) agreement for the different radiographic techniques and for the different bur sizes. Conventional Radiography outperformed Digital Radiography in diagnosing periapical lesions made with Size two bur. Both were equally diagnostic for lesions made with larger bur sizes. Colour coding method was least accurate among all the techniques. Conclusion: Conventional radiography traditionally forms the backbone in the diagnosis, treatment planning and follow-up of periapical lesions. Direct digital imaging is an efficient technique, in diagnostic sense. Colour coding of digital radiography was feasible but less accurate however, this imaging technique, like any other, needs to be studied continuously with the emphasis on safety of patients and diagnostic quality of images. PMID:25584318

  13. Commentary on ``Future directions: Building technologies and design tools``

    Quadrel, R.W.

    1992-08-10

    This paper presents a number of interesting and thought-provoking scenarios about the future use of advanced technology in the design and operation of commercial buildings. I will express my reactions in the following series of short paragraphs. These thoughts will, I hope, raise some new questions and offer fruitful directions for further exploration.

  14. Directional well trajectory design: The effect of change of Azimuth ...

    Across several texts dealing on the issue of the Build-&-Hold and Continuous Build basic well trajectory designs, it was observed that entire mathematical expressions were based on a direct or straight azimuth departure course. In this work, the effect of a curved bend in azimuth from the kick-off to the target of the well ...

  15. Photonic crystal fiber design for broadband directional coupling

    Lægsgaard, Jesper; Bang, Ole; Bjarklev, Anders Overgaard

    2004-01-01

    A novel design for a broadband directional coupler based on a photonic crystal fiber is investigated numerically. It is shown that suitable index-depressing doping of the core regions in an index-guiding twin-core photonic crystal fiber can stabilize the coupling coefficient between the cores over...

  16. Web Interface Design Principles for Adults' Self-Directed Learning

    Firat, Mehmet; Sakar, A. Nurhan; Kabakci Yurdakul, Isil

    2016-01-01

    One of the most important features which e-learning tools and environments must possess within the scope of lifelong learning is self-directed learning, which can be considered as a form of self-learning. The aim of this study was to determine, based on the views and recommendations of experts, interface design principles for the development of…

  17. Design directions for media-supported collocated remembering practices

    Broekhuijsen, M.; van den Hoven, E.; Markopoulos, P.

    2017-01-01

    Since the widespread adoption of digital photography, people create many digital photos, often with the intention to use them for shared remembering. Practices around digital photography have changed along with advances in media sharing technologies such as smartphones, social media, and mobile

  18. Clinical evaluation of digital angiographic system equipped with the Safire' flat-panel detector of a direct conversion type

    Miura, Yoshiaki; Miura, Yusuke; Goto, Keiichi [Shimadzu Corporation, Medical Systems Division, Research and Development, Kyoto (JP)] [and others

    2003-06-01

    This report presents a report on clinical evaluation of our newly developed flat-panel X-ray detector of a direct conversion type, designed to provide images of a resolution higher than, or at least equal to, that ensured by X-ray photographic films, in clinical digital X-ray cinematography. This new detector was named 'Safire' the acronym of 'Shimadzu advanced flat imaging receptor', emphasizing its high technological level, such as the capability to ensure high quality of images. The clinical evaluation of Shimadzu DIGITEX Premier digital angiography system, equipped with this new flat-panel X-ray detector of a direct conversion type, has been started in March, 2003, at the Kokura Memorial Hospital in Kyushu, Japan. (author)

  19. Multi performance option in direct displacement based design

    Muljati Ima

    2017-01-01

    Full Text Available Compare to traditional method, direct displacement based design (DDBD offers the more rational design choice due to its compatibility with performance based design which is controlled by the targeted displacement in design. The objectives of this study are: 1 to explore the performance of DDBD for design Level-1, -2 and -3; 2 to determine the most appropriate design level based on material efficiency and damage risk; and 3 to verify the chosen design in order to check its performance under small-, moderate- and severe earthquake. As case study, it uses regular concrete frame structures consists of fourand eight-story with typical plan, located in low- and high-risk seismicity area. The study shows that design Level-2 (repairable damage is the most appropriate choice. Nonlinear time history analysis is run for each case study in order to verify their performance based on parameter: story drift, damage indices, and plastic mechanism. It can be concluded that DDBD performed very well in predicting seismic demand of the observed structures. Design Level-2 can be chosen as the most appropriate design level. Structures are in safe plastic mechanism under all level of seismicity although some plastic hinges formed at some unexpected locations.

  20. Design And Construction Of Digital Multi-Meter Using PIC Microcontroller

    Khawn Nue

    2015-07-01

    Full Text Available Abstract This thesis describes the design and construction of digital multi-meter using PIC microcontroller. In this system a typical multi-meter may include features such as the ability to measure ACDC voltage DC current resistance temperature diodes frequency and connectivity. This design uses of the PIC microcontroller voltage rectifiers voltage divide potentiometer LCD and other instruments to complete the measure. When we used what we have learned of microprocessors and adjust the program to calculate and show the measures in the LCD keypad selected the modes. The software programming has been incorporated using MPLAB and PROTEUS. In this system the analogue input is taken directly to the analogue input pin of the microcontroller without any other processing. So the input range is from 0V to 5V the maximum source impedance is 2k5 for testing use a 1k pot. To improve the circuit adds an op-amp in front to present greater impedance to the circuit under test. The output impedance of the op-amp will be low which a requirement of the PIC analogue input is.

  1. Accuracy of digital models obtained by direct and indirect data capturing.

    Güth, Jan-Frederik; Keul, Christine; Stimmelmayr, Michael; Beuer, Florian; Edelhoff, Daniel

    2013-05-01

    With direct and indirect digitalisation, two access points to CAD/CAM-generated restorations are available. The aim of this study was to compare the accuracy of the single steps of both approaches by comparing construction datasets using a new methodology. Twelve test datasets were generated in vitro (1) with the Lava Chairside Oral Scanner (COS) (2) by digitizing polyether impressions (IMP) and (3) by scanning the referring gypsum cast by the Lava Scan ST laboratory scanner (ST) at a time. Using an inspection software, these datasets were superimposed by a best fit algorithm with the reference dataset (REF), gained from industrial computed tomography, and divergences were analysed. On the basis of average positive and negative deviations between test- and REF datasets, it could be shown that direct digitalisation accomplished the most accurate results (COS, 17 μm/-13 μm; SD ± 19 μm), followed by digitized polyether impression (IMP, 23 μm/-22 μm; SD ± 31 μm) and indirect digitalisation (ST, 36 μm/-35 μm; SD ± 52 μm). The mean absolute values of Euclidean distances showed the least values for COS (15 μm; SD ± 6 μm), followed by IMP (23 μm; SD ± 9 μm) and ST (36 μm; SD ± 7 μm). The mean negative and mean absolute values of all groups were significantly different. Comparing the mean positive values of the groups, IMP and COS (p = 0.082) showed no significant difference, whereas ST and COS, and ST and IMP exhibited statistically significant differences. Within the limitations of this in vitro study, the direct digitalisation with Lava C.O.S. showed statistically significantly higher accuracy compared to the conventional procedure of impression taking and indirect digitalisation. Within the limitations of this study, the method of direct digitalisation seems to have the potential to improve the accuracy of impressions for four-unit FDPs.

  2. Designed cell consortia as fragrance-programmable analog-to-digital converters.

    Müller, Marius; Ausländer, Simon; Spinnler, Andrea; Ausländer, David; Sikorski, Julian; Folcher, Marc; Fussenegger, Martin

    2017-03-01

    Synthetic biology advances the rational engineering of mammalian cells to achieve cell-based therapy goals. Synthetic gene networks have nearly reached the complexity of digital electronic circuits and enable single cells to perform programmable arithmetic calculations or to provide dynamic remote control of transgenes through electromagnetic waves. We designed a synthetic multilayered gaseous-fragrance-programmable analog-to-digital converter (ADC) allowing for remote control of digital gene expression with 2-bit AND-, OR- and NOR-gate logic in synchronized cell consortia. The ADC consists of multiple sampling-and-quantization modules sensing analog gaseous fragrance inputs; a gas-to-liquid transducer converting fragrance intensity into diffusible cell-to-cell signaling compounds; a digitization unit with a genetic amplifier circuit to improve the signal-to-noise ratio; and recombinase-based digital expression switches enabling 2-bit processing of logic gates. Synthetic ADCs that can remotely control cellular activities with digital precision may enable the development of novel biosensors and may provide bioelectronic interfaces synchronizing analog metabolic pathways with digital electronics.

  3. Information Architecture the Design of Digital Information Spaces

    Ding, Wei

    2009-01-01

    Information Architecture is about organizing and simplifying information, designing and integrating information spaces/systems, and creating ways for people to find and interact with information content. Its goal is to help people understand and manage information and make right decisions accordingly. In the ever-changing social, organizational and technological contexts, Information Architects not only design individual information spaces (e.g., individual websites, software applications, and mobile devices), but also tackle strategic aggregation and integration of multiple information spaces

  4. Digital Omotenashi: Toward a Smart Tourism Design Systems

    Chaeyoung Lim; Noha Mostafa; Jaehyun Park

    2017-01-01

    The tourism industry is currently facing many challenges; one of the main challenges is the lack of having smart tourism systems that make use of the recent advances in information and communication technology. Another challenge is designing such smart tourism systems while embracing diversified tourists’ sustainable values of experience (functional values, social values, emotional values, and epistemic values). In light of these challenges, the overall objective of this work is to design a s...

  5. Design and development of a digital farmer field school. Experiences with a digital learning environment for cocoa production and certification in Sierra Leone

    Witteveen, Loes; Lie, Rico; Goris, Margriet; Ingram, Verina

    2017-01-01

    This article reports on the design and development of the Digital Farmer Field School (DFFS). The DFFS offers a tablet-based digital learning environment for farmers and extension agents for knowledge sharing and knowledge co-creation. It provides an alternative to conventional agricultural

  6. Design and theoretical investigation of a digital x-ray detector with large area and high spatial resolution

    Gui, Jianbao; Guo, Jinchuan; Yang, Qinlao; Liu, Xin; Niu, Hanben

    2007-05-01

    X-ray phase contrast imaging is a promising new technology today, but the requirements of a digital detector with large area, high spatial resolution and high sensitivity bring forward a large challenge to researchers. This paper is related to the design and theoretical investigation of an x-ray direct conversion digital detector based on mercuric iodide photoconductive layer with the latent charge image readout by photoinduced discharge (PID). Mercuric iodide has been verified having a good imaging performance (high sensitivity, low dark current, low voltage operation and good lag characteristics) compared with the other competitive materials (α-Se,PbI II,CdTe,CdZnTe) and can be easily deposited on large substrates in the manner of polycrystalline. By use of line scanning laser beam and parallel multi-electrode readout make the system have high spatial resolution and fast readout speed suitable for instant general radiography and even rapid sequence radiography.

  7. The design of KRT digital system in Ling'ao Ⅱ

    Sun Yuanjun; Zhang Renyan; Zhao Weijun

    2013-01-01

    In the design of KRT system in Ling Ao Ⅱ, it requires the hardware composition shall be similar to that of Ling Ao Ⅰ. At the same time, the KRT system should be digitized and centralized. In order to realize the goal, the KRT system will be divided into the lower and upper parts. The local sensor at the lower part will transform the analog signal to digital signal in the local display unit; then the digital signals are sent to the upper part (cabinet) by RS-485; the cabinet collects the signals, saves and displays them in the server or operation workstation. or sends them to the DCS. On the other hand, the digital signals will be treated into analog or on/off signals in cabinet and transmitted to other systems. (authors)

  8. Design, implementation and analysis of fully digital 1-D controllable multiscroll chaos

    Mansingka, Abhinav S.; Radwan, Ahmed G.; Salama, Khaled N.

    2011-01-01

    This paper introduces the fully digital implementation of a 1-D multiscroll chaos generator based on a staircase nonlinearity in the 3rd-order jerk system using the Euler approximation. For the first time, digital design is exploited to provide real-time controllability of (i) number of scrolls, (ii) position in 1-D space, (iii) Euler step size and (iv) system parameter. The effect of variations in these fields on the maximum Lyapunov exponent (MLE) is analyzed. The system is implemented using Verilog HDL and synthesized on an Xilinx Virtex 4 FPGA, exhibiting area utilization less than 3.5% and high performance with experimentally verified throughput up to 3.33 Gbits/s. This fully digital system enables applications in modulation schemes and chaos-based cryptosystems without analog to digital conversion. © 2011 IEEE.

  9. Design, implementation and analysis of fully digital 1-D controllable multiscroll chaos

    Mansingka, Abhinav S.

    2011-12-01

    This paper introduces the fully digital implementation of a 1-D multiscroll chaos generator based on a staircase nonlinearity in the 3rd-order jerk system using the Euler approximation. For the first time, digital design is exploited to provide real-time controllability of (i) number of scrolls, (ii) position in 1-D space, (iii) Euler step size and (iv) system parameter. The effect of variations in these fields on the maximum Lyapunov exponent (MLE) is analyzed. The system is implemented using Verilog HDL and synthesized on an Xilinx Virtex 4 FPGA, exhibiting area utilization less than 3.5% and high performance with experimentally verified throughput up to 3.33 Gbits/s. This fully digital system enables applications in modulation schemes and chaos-based cryptosystems without analog to digital conversion. © 2011 IEEE.

  10. Design of a portable directional neutron source finder

    Yamanishi, Hirokuni

    2005-01-01

    An instrument that determines the direction of a remote existing neutron source has been designed. This instrument combines a polyethylene block and four 3 He counter tubes. The advantages of the instrument are portability and good angular resolution. The count from the detector was varied with the neutron incident angle due to the moderator. Using this characteristic, the direction of the neutron source can be measured precisely by revising the axis of the instrument so that the difference between the four detectors measurements is minimized. Consequently, the direction of the central axis of the instrument in which the response difference of the four detectors reaches a minimum indicates the direction of the neutron source. The practical use of the instrument was demonstrated by 252 Cf source irradiation experiment and MCNP simulation

  11. Vroom: designing an augmented environment for remote collaboration in digital cinema production

    Margolis, Todd; Cornish, Tracy

    2013-03-01

    As media technologies become increasingly affordable, compact and inherently networked, new generations of telecollaborative platforms continue to arise which integrate these new affordances. Virtual reality has been primarily concerned with creating simulations of environments that can transport participants to real or imagined spaces that replace the "real world". Meanwhile Augmented Reality systems have evolved to interleave objects from Virtual Reality environments into the physical landscape. Perhaps now there is a new class of systems that reverse this precept to enhance dynamic media landscapes and immersive physical display environments to enable intuitive data exploration through collaboration. Vroom (Virtual Room) is a next-generation reconfigurable tiled display environment in development at the California Institute for Telecommunications and Information Technology (Calit2) at the University of California, San Diego. Vroom enables freely scalable digital collaboratories, connecting distributed, high-resolution visualization resources for collaborative work in the sciences, engineering and the arts. Vroom transforms a physical space into an immersive media environment with large format interactive display surfaces, video teleconferencing and spatialized audio built on a highspeed optical network backbone. Vroom enables group collaboration for local and remote participants to share knowledge and experiences. Possible applications include: remote learning, command and control, storyboarding, post-production editorial review, high resolution video playback, 3D visualization, screencasting and image, video and multimedia file sharing. To support these various scenarios, Vroom features support for multiple user interfaces (optical tracking, touch UI, gesture interface, etc.), support for directional and spatialized audio, giga-pixel image interactivity, 4K video streaming, 3D visualization and telematic production. This paper explains the design process that

  12. Digital Omotenashi: Toward a Smart Tourism Design Systems

    Chaeyoung Lim

    2017-11-01

    Full Text Available The tourism industry is currently facing many challenges; one of the main challenges is the lack of having smart tourism systems that make use of the recent advances in information and communication technology. Another challenge is designing such smart tourism systems while embracing diversified tourists’ sustainable values of experience (functional values, social values, emotional values, and epistemic values. In light of these challenges, the overall objective of this work is to design a smart tourism experience-centered system that considers social and technical perspectives. The Socio-Technical Systems theory was adopted as a theoretical foundation, and the Design Science Research methodology was used to develop a smart tourism system and a practical design artifact. A case study from the Japanese tourism context was studied by exploring tourists’ sustainable values of experiences and local staffs’ behaviors. The main problem was the dysfunctional communication between local service staffs and foreign tourists during the service process. After identifying the problem and the objectives, a relevant smart tourism system was synthesized and tested as a design artifact. The results of the utility test of the proposed artifact showed its effectiveness and efficiency in facilitating the service process and in creating multi-dimensional values of experience.

  13. Integrated source and channel encoded digital communication system design study

    Alem, W. K.; Huth, G. K.; Simon, M. K.

    1978-01-01

    The particular Ku-band carrier, PN despreading, and symbol synchronization strategies, which were selected for implementation in the Ku-band transponder aboard the orbiter, were assessed and evaluated from a systems performance viewpoint, verifying that system specifications were met. A study was performed of the design and implementation of tracking techniques which are suitable for incorporation into the Orbiter Ku-band communication system. Emphasis was placed on maximizing tracking accuracy and communication system flexibility while minimizing cost, weight, and system complexity of Orbiter and ground systems hardware. The payload communication study assessed the design and performance of the forward link and return link bent-pipe relay modes for attached and detached payloads. As part of this study, a design for a forward link bent-pipe was proposed which employs a residual carrier but which is tracked by the existing Costas loop.

  14. Development strategy and process models for phased automation of design and digital manufacturing electronics

    Korshunov, G. I.; Petrushevskaya, A. A.; Lipatnikov, V. A.; Smirnova, M. S.

    2018-03-01

    The strategy of quality of electronics insurance is represented as most important. To provide quality, the processes sequence is considered and modeled by Markov chain. The improvement is distinguished by simple database means of design for manufacturing for future step-by-step development. Phased automation of design and digital manufacturing electronics is supposed. The MatLab modelling results showed effectiveness increase. New tools and software should be more effective. The primary digital model is proposed to represent product in the processes sequence from several processes till the whole life circle.

  15. Digital Direct-to-Consumer Advertising: A Perfect Storm of Rapid Evolution and Stagnant Regulation

    Mackey, Tim K.

    2016-01-01

    The adoption and use of digital forms of direct-to-consumer advertising (also known as "eDTCA") is on the rise. At the same time, the universe of eDTCA is expanding, as technology on Internet-based platforms continues to evolve, from static websites, to social media, and nearly ubiquitous use of mobile devices. However, little is known about how this unique form of pharmaceutical marketing impacts consumer behavior, public health, and overall healthcare utilization. The study by Kim analyzing US Food and Drug Administration (FDA) notices of violations (NOVs) and warning letters regarding online promotional activities takes us in the right direction, but study results raise as many questions as it does answers. Chief among these are unanswered concerns about the unique regulatory challenges posed by the "disruptive" qualities of eDTCA, and whether regulators have sufficient resources and oversight powers to proactively address potential violations. Further, the globalization of eDTCA via borderless Internet-based technologies raises larger concerns about the potential global impact of this form of health marketing unique to only the United States and New Zealand. Collectively, these challenges make it unlikely that regulatory science will be able to keep apace with the continued rapid evolution of eDTCA unless more creative policy solutions are explored. PMID:27239871

  16. Direct conversion Si and CdZnTe detectors for digital mammography

    Yin Shi Shi; Maeding, D; Mainprize, J; Mawdsley, G; Yaffe, M J; Gordon, E E; Hamilton, W J

    2000-01-01

    Hybrid pixel detector arrays that convert X-rays directly into charge signals are under development at NOVA for application to digital mammography. This technology also has wide application possibilities in other fields of radiology or in industrial imaging, nondestructive evaluation (NDE) and nondestructive inspection (NDI). These detectors have potentially superior properties compared to either emulsion-based film-screen systems which has nonlinear response to X-rays, or phosphor-based detectors in which there is an intermediate step of X-ray to light photon conversion (Feig and Yaffe, Radiol. Clinics North America 33 (1995) 1205-1230). Potential advantages of direct conversion detectors are high quantum efficiencies (QE) of 98% or higher (for 0.3 mm thick CdZnTe detector with 20 keV X-rays), improved contrast, high sensitivity and low intrinsic noise. These factors are expected to contribute to high detective quantum efficiency (DQE). The prototype hybrid pixel detector developed has 50x50 mu m pixel size,...

  17. Designing a Marketing Analytics Course for the Digital Age

    Liu, Xia; Burns, Alvin C.

    2018-01-01

    Marketing analytics is receiving great attention because of evolving technology and the radical changes in the marketing environment. This study aims to assist the design and implementation of a marketing analytics course. We assembled a rich data set from four sources: business executives, 400 employers' job postings, one million tweets about…

  18. The Integration of Interior Architecture Education with Digital Design Approaches

    Yazicioglu, Deniz Ayse

    2011-01-01

    It is inevitable that as a result of progress in technology and the changes in the ways with which design is conceived, interior architecture schools should be updated according to these requirements and that new educational processes should be tried out. It is for this reason that the scope and aim of this study have been determined as being the…

  19. Automatic design of optical systems by digital computer

    Casad, T. A.; Schmidt, L. F.

    1967-01-01

    Computer program uses geometrical optical techniques and a least squares optimization method employing computing equipment for the automatic design of optical systems. It evaluates changes in various optical parameters, provides comprehensive ray-tracing, and generally determines the acceptability of the optical system characteristics.

  20. Design research as a framework to evaluate the usability and accessibility of the digital doorway

    Adebesin, F

    2011-09-01

    Full Text Available , and then also evaluated the usability and direct accessibility support provided by the Digital Doorway, a non-standard computer system deployed amongst underprivileged communities in South Africa with the aim of promoting computer literacy. This paper discusses...

  1. Direct-drive–ignition designs with mid-Z ablators

    Lafon, M.; Betti, R. [Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623 (United States); Laboratory for Laser Energetics and Fusion Science Center, University of Rochester, 250 East River Road, Rochester, New York 14623 (United States); Anderson, K. S.; Collins, T. J. B.; Epstein, R.; McKenty, P. W.; Myatt, J. F.; Shvydky, A.; Skupsky, S. [Laboratory for Laser Energetics, University of Rochester, 250 East River Road, Rochester, New York 14623 (United States)

    2015-03-15

    Achieving thermonuclear ignition using direct laser illumination relies on the capability to accelerate spherical shells to high implosion velocities while maintaining shell integrity. Ablator materials of moderate atomic number Z reduce the detrimental effects of laser–plasma instabilities in direct-drive implosions. To validate the physics of moderate-Z ablator materials for ignition target designs on the National Ignition Facility (NIF), hydro-equivalent targets are designed using pure plastic (CH), high-density carbon, and glass (SiO{sub 2}) ablators. The hydrodynamic stability of these targets is investigated through two-dimensional (2D) single-mode and multimode simulations. The overall stability of these targets to laser-imprint perturbations and low-mode asymmetries makes it possible to design high-gain targets. Designs using polar-drive illumination are developed within the NIF laser system specifications. Mid-Z ablator targets are an attractive candidate for direct-drive ignition since they present better overall performance than plastic ablator targets through reduced laser–plasma instabilities and a similar hydrodynamic stability.

  2. Antenna Design for Directivity-Enhanced Raman Spectroscopy

    Aftab Ahmed

    2012-01-01

    Full Text Available Antenna performance can be described by two fundamental parameters: directivity and radiation efficiency. Here, we demonstrate nanoantenna designs in terms of improved directivity. Performance of the antennas is demonstrated in Raman scattering experiments. The radiated beam is directed out of the plane by using a ground plane reflector for easy integration with commercial microscopes. Parasitic elements and parabolic and waveguide nanoantennas with a ground plane are explored. The nanoantennas were fabricated by a series of electron beam evaporation steps and focused ion beam milling. As we have shown previously, the circular waveguide nanoantenna boosts the measured Raman signal by 5.5x with respect to a dipole antenna over a ground plane; here, we present the design process that led to the development of that circular waveguide nanoantenna. This work also shows that the parabolic nanoantenna produces a further fourfold improvement in the measured Raman signal with respect to a circular waveguide nanoantenna. The present designs are nearly optimal in the sense that almost all the beam power is coupled into the numerical aperture of the microscope. These designs can find applications in microscopy, spectroscopy, light-emitting devices, photovoltaics, single-photon sources, and sensing.

  3. Design Preliminaries for Direct Drive under Water Wind Turbine Generator

    Leban, Krisztina Monika; Ritchie, Ewen; Argeseanu, Alin

    2012-01-01

    This paper focuses on the preliminary design process of a 20 MW electric generator. The application calls for an offshore, vertical axis, direct drive wind turbine. Arguments for selecting the type of electric machine for the application are presented and discussed. Comparison criteria for deciding...... on a type of machine are listed. Additional constraints emerging from the direct drive, vertical axis concepts are considered. General rules and a preliminary algorithm are discussed for the machine selected to be most suitable for the imposed conditions....

  4. In vivo comparison of Kodak E-speed film and direct digital imaging system for assessment of interproximal bone loss

    Mellekatte C Neetha

    2014-01-01

    Full Text Available Aims: To evaluate the diagnostic accuracy of direct digital radiography as compared to a conventional radiographic film for the assessment of interproximal bone loss with intrasurgical measurements as the gold standard. Materials and Methods: A total of 100 patients, with untreated moderate-to-advanced periodontal disease, were included in the study. The presurgical radiographs were made using a Kodak E-speed film and a Dexis digital sensor simultaneously, for sites with interproximal bone loss. At the time of surgery, the distance from the cementoenamel junction to the bone defect (CEJ-BD was measured for 331 interproximal defects. The radiographs were randomized and then linear measurements were taken for the same sites in both conventional and digital radiographs. Stastistical Analysis: Comparison between the conventional, digital, and intrasurgical measurements was done statistically using the Student′s t-test. The agreement and correlation among the methods was assessed using the weighted Kappa measure of agreement and Pearson′s correlation, respectively. Results: The results showed that the conventional (5.15 ± 2.19 mm and digital analyzing techniques (5.13 ± 2.19 mm underestimated the interproximal bone loss, as compared to the intrasurgical measurements (6.07 ± 2.05 mm (p < 0.001. The difference between conventional and digital radiographic methods was found to be statistically insignificant (p = 0.92. Conclusion: Under normal clinical use, the alveolar bone levels revealed on intraoral direct digital radiographs and Kodak E speed film were almost same. Therefore, the digital radiographic system can be routinely used in clinical practice as an alternative to conventional film.

  5. Efficient Algorithms and Design for Interpolation Filters in Digital Receiver

    Xiaowei Niu

    2014-05-01

    Full Text Available Based on polynomial functions this paper introduces a generalized design method for interpolation filters. The polynomial-based interpolation filters can be implemented efficiently by using a modified Farrow structure with an arbitrary frequency response, the filters allow many pass- bands and stop-bands, and for each band the desired amplitude and weight can be set arbitrarily. The optimization coefficients of the interpolation filters in time domain are got by minimizing the weighted mean squared error function, then converting to solve the quadratic programming problem. The optimization coefficients in frequency domain are got by minimizing the maxima (MiniMax of the weighted mean squared error function. The degree of polynomials and the length of interpolation filter can be selected arbitrarily. Numerical examples verified the proposed design method not only can reduce the hardware cost effectively but also guarantee an excellent performance.

  6. Sliding spool design for reducing the actuation forces in direct operated proportional directional valves: Experimental validation

    Amirante, Riccardo; Distaso, Elia; Tamburrano, Paolo

    2016-01-01

    Highlights: • An innovative procedure to design a commercial proportional directional valve is shown. • Experimental tests are performed to demonstrate the flow force reduction. • The design is improved by means of a previously made optimization procedure. • Great reduction in the flow forces without reducing the flow rate is demonstrated. - Abstract: This paper presents the experimental validation of a new methodology for the design of the spool surfaces of four way three position direct operated proportional directional valves. The proposed methodology is based on the re-design of both the compensation profile (the central conical surface of the spool) and the lateral surfaces of the spool, in order to reduce the flow forces acting on the spool and hence the actuation forces. The aim of this work is to extend the application range of these valves to higher values of pressure and flow rate, thus avoiding the employment of more expensive two stage configurations in the case of high-pressure conditions and/or flow rate. The paper first presents a theoretical approach and a general strategy for the sliding spool design to be applied to any four way three position direct operated proportional directional valve. Then, the proposed approach is experimentally validated on a commercially available valve using a hydraulic circuit capable of measuring the flow rate as well as the actuation force over the entire spool stroke. The experimental results, performed using both the electronic driver provided by the manufacturer and a manual actuation system, show that the novel spool surface requires remarkably lower actuation forces compared to the commercial configuration, while maintaining the same flow rate trend as a function of the spool position.

  7. Prosthetic design directives: Low-cost hands within reach.

    Jones, G K; Rosendo, A; Stopforth, R

    2017-07-01

    Although three million people around the world suffer from the lack of one or both upper limbs 80% of this number is located within developing countries. While prosthetic prices soar with technology 3D printing and low cost electronics present a sensible solution for those that cannot afford expensive prosthetics. The electronic and control design of a low-cost prosthetic hand, the Touch Hand II, is discussed. This paper shows that sensorless techniques can be used to reduce design complexities, costs, and provide easier access to the electronics. A closing and opening finite state machine (COFSM) was developed to handle the actuated digit joint control state and a supervisory switching control scheme, used for speed and grip strength control. Three torque and speed settings were created to be preset for specific grasps. The hand was able to replicate ten frequently used grasps and grip some common objects. Future work is necessary to enable a user to control it with myoelectric signals (MESs) and to solve operational problems related to electromagnetic interference (EMI).

  8. Design and characterization of dielectric-loaded plasmonic directional couplers

    Stær, Tobias Holmgaard; Chen, Zhuo; Bozhevolnyi, Sergey

    2009-01-01

    Ultracompact directional couplers (DCs) based on dielectric-loaded surface plasmon-polariton waveguides (DLSPPWs) are analyzed using the effective index method (EIM), with the coupling, both in the parallel interaction region and in- and out-coupling regions, being taken into account. Near-field...... characterization of fabricated DCs performed with a scanning near-field optical microscope verifies the applicability of the EIM in the analysis and design of DLSPPW-based wavelength-selective DCs. The design approach applicable to a large variety of integrated optical waveguides is developed, enabling...

  9. Airborne hyperspectral observations of surface and cloud directional reflectivity using a commercial digital camera

    A. Ehrlich

    2012-04-01

    Full Text Available Spectral radiance measurements by a digital single-lens reflex camera were used to derive the directional reflectivity of clouds and different surfaces in the Arctic. The camera has been calibrated radiometrically and spectrally to provide accurate radiance measurements with high angular resolution. A comparison with spectral radiance measurements with the Spectral Modular Airborne Radiation measurement sysTem (SMART-Albedometer showed an agreement within the uncertainties of both instruments (6% for both. The directional reflectivity in terms of the hemispherical directional reflectance factor (HDRF was obtained for sea ice, ice-free ocean and clouds. The sea ice, with an albedo of ρ = 0.96 (at 530 nm wavelength, showed an almost isotropic HDRF, while sun glint was observed for the ocean HDRF (ρ = 0.12. For the cloud observations with ρ = 0.62, the cloudbow – a backscatter feature typically for scattering by liquid water droplets – was covered by the camera. For measurements above heterogeneous stratocumulus clouds, the required number of images to obtain a mean HDRF that clearly exhibits the cloudbow has been estimated at about 50 images (10 min flight time. A representation of the HDRF as a function of the scattering angle only reduces the image number to about 10 (2 min flight time.

    The measured cloud and ocean HDRF have been compared to radiative transfer simulations. The ocean HDRF simulated with the observed surface wind speed of 9 m s−1 agreed best with the measurements. For the cloud HDRF, the best agreement was obtained by a broad and weak cloudbow simulated with a cloud droplet effective radius of Reff = 4 μm. This value agrees with the particle sizes derived from in situ measurements and retrieved from the spectral radiance of the SMART-Albedometer.

  10. Direction of Radio Finding via MUSIC (Multiple Signal Classification) Algorithm for Hardware Design System

    Zhang, Zheng

    2017-10-01

    Concept of radio direction finding systems, which use radio direction finding is based on digital signal processing algorithms. Thus, the radio direction finding system becomes capable to locate and track signals by the both. Performance of radio direction finding significantly depends on effectiveness of digital signal processing algorithms. The algorithm uses the Direction of Arrival (DOA) algorithms to estimate the number of incidents plane waves on the antenna array and their angle of incidence. This manuscript investigates implementation of the DOA algorithms (MUSIC) on the uniform linear array in the presence of white noise. The experiment results exhibit that MUSIC algorithm changed well with the radio direction.

  11. Digital Game Playing and Direct and Indirect Aggression in Early Adolescence: The Roles of Age, Social Intelligence, and Parent-Child Communication

    Wallenius, Marjut; Punamaki, Raija-Leena; Rimpela, Arja

    2007-01-01

    The roles of age, social intelligence and parent-child communication in moderating the association between digital game playing and direct and indirect aggression were examined in 478 Finnish 10- and 13-year-old schoolchildren based on self-reports. The results confirmed that digital game violence was directly associated with direct aggression,…

  12. Approach to interior design for passive direct gain solar homes

    Kachadorian, C.C.

    1980-01-01

    In response to requests from buyers and builders of direct gain passive solar homes interior design criteria either specific to, or emphasized by, passive solar buildings are investigated. Problems of high sunlight penetration, secondary illumination, material selection, sound control and psychology are approached. Material deterioration, fading, glare, noise, and a sense of spacial confinement can be minimized, contributing to the appeal and saleability of passive solar homes.

  13. Noise-shaping all-digital phase-locked loops modeling, simulation, analysis and design

    Brandonisio, Francesco

    2014-01-01

    This book presents a novel approach to the analysis and design of all-digital phase-locked loops (ADPLLs), technology widely used in wireless communication devices. The authors provide an overview of ADPLL architectures, time-to-digital converters (TDCs) and noise shaping. Realistic examples illustrate how to analyze and simulate phase noise in the presence of sigma-delta modulation and time-to-digital conversion. Readers will gain a deep understanding of ADPLLs and the central role played by noise-shaping. A range of ADPLL and TDC architectures are presented in unified manner. Analytical and simulation tools are discussed in detail. Matlab code is included that can be reused to design, simulate and analyze the ADPLL architectures that are presented in the book.   • Discusses in detail a wide range of all-digital phase-locked loops architectures; • Presents a unified framework in which to model time-to-digital converters for ADPLLs; • Explains a procedure to predict and simulate phase noise in oscil...

  14. 75 FR 20518 - Special Conditions: Cirrus Design Corporation Model SF50 Airplane; Full Authority Digital Engine...

    2010-04-20

    ... issuance. Comments Invited Interested persons are invited to submit such written data, views, or arguments... On September 9, 2008, Cirrus Design Corporation applied for a type certificate for their new model... the digital engine control must provide an equivalent reliability to mechanical engine controls. Type...

  15. Freed : a system for creating multiple views of a digital collection during the design process

    Mendels, P.; Overbeeke, C.J.; Frens, J.W.

    2011-01-01

    In this paper Freed is presented, a system that enables design students to spatially organize their digital collection, define relations between collection content and reflect on it. The system features a force-based layout that allows to explore spatial organizations, and hence to gain new

  16. Toward User Interfaces and Data Visualization Criteria for Learning Design of Digital Textbooks

    Railean, Elena

    2014-01-01

    User interface and data visualisation criteria are central issues in digital textbooks design. However, when applying mathematical modelling of learning process to the analysis of the possible solutions, it could be observed that results differ. Mathematical learning views cognition in on the base on statistics and probability theory, graph…

  17. A Design to Digitalize Hydraulic Cylinder Control of a Machine Tool ...

    Conventionally hydraulic piston - cylinder servos are actuated using analogue controls for machine tool axis drives. In this paper a design of the axis control system of an NC milling machine which employs a small stepping motor to digitally actuated hydraulic piston - cylinder servo drives existing on the machines Y-axis is ...

  18. Safety and security aspects in design of digital safety I and C in nuclear power plants

    Ding, Yongjian; Waedt, Karl

    2016-01-01

    The paper describes a safety objective oriented systematic design approach of digital (computerized) safety I and C in modern nuclear power plants which considers the plant safety requirements as well as cybersecurity needs. The defence in depth philosophy is applied by using different defence lines in the I and C architecture and protection zones in the plant IT environment.

  19. The Participatory Design of a (Today and) Future Digital Entomology Lab

    Hai-Jew, Shalin

    2011-01-01

    This article showcases a virtual interactive participatory design activity for building a digital entomology lab. Conceptualized as a virtual complement to a general entomology course at Kansas State University, the lab would allow learners to explore morphological aspects of insects--their various forms and functions--in order to understand…

  20. The design and implementation of an infrastructure for multimedia digital libraries

    de Vries, A.P.; Eberman, B.; Kovalcin, D.E.

    We develop an infrastructure for managing, indexing and serving multimedia content in digital libraries. This infrastructure follows the model of the web, and thereby is distributed in nature. We discuss the design of the Librarian, the component that manages meta data about the content. The

  1. Creative Design of Digital Cognitive Games: Application of Cognitive Toys and Isomorphism

    Sedig, Kamran; Haworth, Robert

    2012-01-01

    Digital cognitive games (DCGs) are games whose primary purpose is to mediate (i.e., support, develop, and enhance) cognitive activities such as problem solving, decision making, planning, and critical reasoning. As these games increase in popularity and usage, more attention should be paid to their design. Currently, there is a lack of design…

  2. Design of digital trapezoidal shaping filter based on LabVIEW

    Liu Yujuan; Qin Guoxiu; Yang Zhihui; Zhang Xiaodong

    2013-01-01

    It describes the design of a digital trapezoidal shaping filter to nuclear signals based on LabVIEW. A method of optimizing the trapezoidal shaping filter's parameters was presented and tested, and the test results of the effect of shaping filter algorithm were studied. (authors)

  3. Macromodels of digital integrated circuits for program packages of circuit engineering design

    Petrenko, A. I.; Sliusar, P. B.; Timchenko, A. P.

    1984-04-01

    Various aspects of the generation of macromodels of digital integrated circuits are examined, and their effective application in program packages of circuit engineering design is considered. Three levels of macromodels are identified, and the application of such models to the simulation of circuit outputs is discussed.

  4. On design-oriented research and digital learning materials in higher education

    Hartog, R.J.M.

    2012-01-01

    The context of the research described in this thesis is formed by a number of research projects that were aimed at the design, development, implementation, use and evaluation of innovative digital learning materials. Most of these projects were carried out mainly within Wageningen University. In

  5. Digital capture, design, and manufacturing of a facial prosthesis: Clinical report on a pediatric patient.

    Grant, Gerald T; Aita-Holmes, Cynthia; Liacouras, Peter; Garnes, Johnathan; Wilson, William O

    2015-07-01

    A digitally captured, designed, and fabricated facial prosthesis is presented as an alternative to customary maxillofacial prosthodontics fabrication techniques, where a facial moulage and patient cooperation may be difficult. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  6. Design Principles for "Thriving in Our Digital World": A High School Computer Science Course

    Veletsianos, George; Beth, Bradley; Lin, Calvin; Russell, Gregory

    2016-01-01

    "Thriving in Our Digital World" is a technology-enhanced dual enrollment course introducing high school students to computer science through project- and problem-based learning. This article describes the evolution of the course and five lessons learned during the design, development, implementation, and iteration of the course from its…

  7. Safety and security aspects in design of digital safety I and C in nuclear power plants

    Ding, Yongjian [University of Applied Sciences Magdeburg-Stendal, Magdeburg (Germany). Inst. of Electrical Engineering; Waedt, Karl [Areva GmbH, Erlangen (Germany). PEAS-G

    2016-05-15

    The paper describes a safety objective oriented systematic design approach of digital (computerized) safety I and C in modern nuclear power plants which considers the plant safety requirements as well as cybersecurity needs. The defence in depth philosophy is applied by using different defence lines in the I and C architecture and protection zones in the plant IT environment.

  8. Extending connections between land and people digitally: designing with rural Herero communities in Namibia

    Bidwell, NJ

    2012-06-01

    Full Text Available -1 Heritage and Social Media: Understanding Heritage in Participatory Culture June 2012/Chapter 11 Extending connections between land and people digitally: designing with rural Herero communities in Namibia Bidwell NJ1 and Winschiers-Theophilus H2 1...

  9. IdeMatch – a digital tool for innovative, social and transdisciplinary learning designs

    Hansen, Gitte Riis

    This paper presents IdeMatch which is a digital tool implemented in University College Zealand (UCZ) in spring 2015. IdeMatch is based on educational policies and educational structural intentions and needs, and this paper examines and offers an outline for the learning perspective and the impact...... that IdeMatch has got concerning teaching and learning designs....

  10. Digital Games, Design, and Learning: A Systematic Review and Meta-Analysis

    Clark, Douglas B.; Tanner-Smith, Emily E.; Killingsworth, Stephen S.

    2016-01-01

    In this meta-analysis, we systematically reviewed research on digital games and learning for K-16 students. We synthesized comparisons of game versus nongame conditions (i.e., media comparisons) and comparisons of augmented games versus standard game designs (i.e., value-added comparisons). We used random-effects meta-regression models with robust…

  11. Enhancing Learning Effectiveness in Digital Design Courses through the Use of Programmable Logic Boards

    Zhu, Yi; Weng, T.; Cheng, Chung-Kuan

    2009-01-01

    Incorporating programmable logic devices (PLD) in digital design courses has become increasingly popular. The advantages of using PLDs, such as complex programmable logic devices (CPLDs) and field programmable gate arrays (FPGA), have been discussed before. However, previous studies have focused on the experiences from the point of view of the…

  12. Formal Learning Sequences and Progression in the Studio: A Framework for Digital Design Education

    Pontus Wärnestål

    2016-02-01

    Full Text Available This paper examines how to leverage the design studio learning environment throughout long-term Digital Design education in order to support students to progress from tactical, well-defined, device-centric routine design, to confidently design sustainable solutions for strategic, complex, problems for a wide range of devices and platforms in the digital space. We present a framework derived from literature on design, creativity, and theories on learning that: (a implements a theory of formal learning sequences as a user-centered design process in the studio; and (b describes design challenge progressions in the design studio environment modeled in seven dimensions. The framework can be used as a tool for designing, evaluating, and communicating course progressions within – and between series of – design studio courses. This approach is evaluated by implementing a formal learning sequence framework in a series of design studio courses that progress in an undergraduate design-oriented Informatics program. Reflections from students, teachers, and external clients indicate high student motivation and learning goal achievement, high teacher satisfaction and skill development, and high satisfaction among external clients.

  13. Direct-Digital Modulation (DIDIMO) Transmitter with -156dBc/Hz Rx-Band Noise using FIR structure

    Fukuda, Shuichi; Miya, Shinji; Io, Miho; Hamashita, Koichi; Nauta, Bram

    2012-01-01

    A direct-digital modulation (DIDIMO) transmitter employing 3-taps 10-bit Finite Impulse Response configuration is proposed and evaluated. FIR-DIDIMO provides simultaneous combination of D/A conversion, up-conversion, power control and also quantization noise filtering at arbitrary offset frequency

  14. Fault-tolerant design of adaptive digital control systems for power plant components

    Parlos, A.G.; Menon, S.K.

    1992-01-01

    An adaptive controller has been designed for the water level of a Westinghouse type U-tube steam generator, and its operation has been demonstrated in the entire power range via computer simulations. The proposed design exhibits improved performance, at low operating powers, a,s compared to existing controller types. The continuous-time controller design is performed systematically via the Linear Quadratic Gaussian/Loop Transfer Recovery method, followed by gain adaptation allowing controller operation in the entire power range. Digital implementation of the controller is accomplished by a digital redesign which results in matching the digital and continuous-time system and controller states. It is only at this stage of the control system design process that issues such as microprocessor induced quantization effects are taken into account. The use of computer-aided-design software greatly expedites the design cycle, allowing the designer to maximize the controller stability robustness to uncertainties via numerous iterations. This inherent controller robustness can be exploited to tolerate incipient plant faults, such as deteriorating U-tube heat transfer properties, without significant loss of controller performance

  15. Design of a continuous digital-output environmental radon monitor

    Wrenn, M.E.; Spitz, H.; Cohen, N.

    1975-01-01

    A new field instrument for the continuous measurement of radon concentrations has been developed to investigate the magnitude and variability of environmental levels of 222 Rn. Passive diffusion of radon, but not its daughters, occurs through an open pore polyurethane foam into a sensitive volume where a static electric field directs the positively ionized radon daughter products to a central collecting electrode. Pulses in a ZnS(Ag) scintillator, resulting from the alpha emission of 218 Po and 214 Po, are observed with a photomultiplier tube and counted using standard NIM electronics. The detector unit has been fabricated into a small, convenient package for indoor air sampling without the use of air movers or pumps. The unit is unobtrusive and acceptable into a daily routine without disrupting normal family or business activities. The monitor can detect as little as 0.5 pCi/l for a 40-min. count (α = .05). The equilibrium detection efficiency of the instrument is 0.7 cpm/pCi/l. (U.S.)

  16. Optimum Design of a Moving Coil Actuator for Fast-Switching Valves in Digital Hydraulic Pumps and Motors

    Roemer, Daniel Beck; Bech, Michael Møller; Johansen, Per

    2015-01-01

    Fast-switching seat valves suitable for digital hydraulic pumps and motors utilize direct electromagnetic actuators, which must exhibit superior transient performance to allow efficient operation of the fluid power pump/motor. A moving coil actuator resulting in a minimum valve switching time...... is designed for such valves using transient finite-element analysis of the electromagnetic circuit. The valve dynamics are coupled to the fluid restrictive forces, which significantly influence the effective actuator force. Fluid forces are modeled based on transient computational fluid dynamics models....... The electromagnetic finite-element model is verified against experimental measurement, and used to design an optimum moving coil actuator for the application considering different voltage-current ratios of the power supply. Results show that the optimum design depends on the supply voltage-current ratio, however...

  17. Design of an ultra-low-power digital processor for passive UHF RFID tags

    Shi Wanggen; Zhuang Yiqi; Li Xiaoming; Wang Xianghua; Jin Zhao; Wang Dan, E-mail: wanggen_shi@163.co [Key Laboratory of the Ministry of Education for Wide Band-Gap Semiconductor Materials and Devices, Institute of Microelectronics, Xidian University, Xi' an 710071 (China)

    2009-04-15

    A new architecture of digital processors for passive UHF radio-frequency identification tags is proposed. This architecture is based on ISO/IEC 18000-6C and targeted at ultra-low power consumption. By applying methods like system-level power management, global clock gating and low voltage implementation, the total power of the design is reduced to a few microwatts. In addition, an innovative way for the design of a true RNG is presented, which contributes to both low power and secure data transaction. The digital processor is verified by an integrated FPGA platform and implemented by the Synopsys design kit for ASIC flows. The design fits different CMOS technologies and has been taped out using the 2P4M 0.35 mum process of Chartered Semiconductor.

  18. Digital tablets and applications in preschool – Preschoolers’ creative transformation of didactic design

    Susanne Kjällander

    2014-12-01

    Full Text Available Little is known about preschoolers and their engagement with digital tablets. This article addresses this gap by drawing on findings from two research projects. The aim is to illustrate how children make meaning, transform and play while engaging with various applications comprised by the materiality of the digital tablets. Empirical video material has been multimodally transcribed and empirical examples are framed by a design theoretical perspective. Findings capture diverse experiences illustrating how preschoolers creatively manipulate and playfully transform didactic designs. The results illustrate how children´s self-initiated play with application’s design shifts the balance of authority that typically exists between adults and children, and the article concludes in a suggestion of how the notion of play can be understood with a design theoretical perspective.

  19. Design of an ultra-low-power digital processor for passive UHF RFID tags

    Shi Wanggen; Zhuang Yiqi; Li Xiaoming; Wang Xianghua; Jin Zhao; Wang Dan

    2009-01-01

    A new architecture of digital processors for passive UHF radio-frequency identification tags is proposed. This architecture is based on ISO/IEC 18000-6C and targeted at ultra-low power consumption. By applying methods like system-level power management, global clock gating and low voltage implementation, the total power of the design is reduced to a few microwatts. In addition, an innovative way for the design of a true RNG is presented, which contributes to both low power and secure data transaction. The digital processor is verified by an integrated FPGA platform and implemented by the Synopsys design kit for ASIC flows. The design fits different CMOS technologies and has been taped out using the 2P4M 0.35 μm process of Chartered Semiconductor.

  20. The impact of specially designed digital games-based learning in undergraduate pathology and medical education.

    Kanthan, Rani; Senger, Jenna-Lynn

    2011-01-01

    The rapid advances of computer technologies have created a new e-learner generation of "Homo-zappien" students that think and learn differently. Digital gaming is an effective, fun, active, and encouraging way of learning, providing immediate feedback and measurable process. Within the context of ongoing reforms in medical education, specially designed digital games, a form of active learning, are effective, complementary e-teaching/learning resources. To examine the effectiveness of the use of specially designed digital games for student satisfaction and for measurable academic improvement. One hundred fourteen students registered in first-year pathology Medicine 102 had 8 of 16 lecture sessions reviewed in specially designed content-relevant digital games. Performance scores to relevant content sessions were analyzed at midterm and final examinations. Seventy-one students who registered in second-year pathology Medicine 202 were exposed to the games only during the final examination, with the midterm examination serving as an internal matched-control group. Outcome measures included performance at midterm and final examinations. Paired 2-tailed t test statistics compared means. A satisfaction survey questionnaire of yes or no responses analyzed student engagement and their perceptions to digital game-based learning. Questions relevant to the game-play sessions had the highest success rate in both examinations among 114 first-year students. In the 71 second-year students, the examination scores at the end of the final examination were significantly higher than the scores on the midterm examination. Positive satisfaction survey noted increased student engagement, enhanced personal learning, and reduced student stress. Specially constructed digital games-based learning in undergraduate pathology courses showed improved academic performance as measured by examination test scores with increased student satisfaction and engagement.

  1. Design and development of a digital phase ratio meter

    Majee, B C [Reactor Control Division, Bhabha Atomic Research Centre, Mumbai (India); Roy, S B; Meghal, A M [Uranium Extraction Division, Bhabha Atomic Research Centre, Mumbai (India)

    1994-06-01

    Uranium purification at Uranium Metal Plant is being carried out using solvent extraction process. The feed is aqueous uranyl nitrate solution with 2-4% insoluble silica particles. The solvent is tri-butyl phosphate diluted with commercial grade kerosene. Extraction is conducted in a slurry extractor equipment using compressed air as mixing and solution-interstage transferring medium. To ensure the organic continuous mode in the mixer and to avoid stable emulsion formation, organic to aqueous ratio maintained in each mixer is 10 to 12 whereas optimum extraction process requires an overall organic to aqueous ratio of 2. Therefore, a high volume of internal recirculation of organic is being arranged by the air-lift in mixers. For a smooth, continuous efficient extraction, mixer organic to aqueous ratio is a very critical parameter and it is required to be monitored periodically to take corrective actions during the operation by controlling the compressed air flow rate. Trials were conducted to select a suitable method of autocontrol of this phase ratio and a system has been designed for this purpose. (author). 3 figs., 1 tab.

  2. Uncertainty Reduction Via Parameter Design of A Fast Digital Integrator for Magnetic Field Measurement

    Arpaia, P; Lucariello, G; Spiezia, G

    2007-01-01

    At European Centre of Nuclear Research (CERN), within the new Large Hadron Collider (LHC) project, measurements of magnetic flux with uncertainty of 10 ppm at a few of decades of Hz for several minutes are required. With this aim, a new Fast Digital Integrator (FDI) has been developed in cooperation with University of Sannio, Italy [1]. This paper deals with the final design tuning for achieving target uncertainty by means of experimental statistical parameter design.

  3. Two-bit trinary full adder design based on restricted signed-digit numbers

    Ahmed, J. U.; Awwal, A. A. S.; Karim, M. A.

    1994-08-01

    A 2-bit trinary full adder using a restricted set of a modified signed-digit trinary numeric system is designed. When cascaded together to design a multi-bit adder machine, the resulting system is able to operate at a speed independent of the size of the operands. An optical non-holographic content addressable memory based on binary coded arithmetic is considered for implementing the proposed adder.

  4. Design and fabrication of multimode interference couplers based on digital micro-mirror system

    Wu, Sumei; He, Xingdao; Shen, Chenbo

    2008-03-01

    Multimode interference (MMI) couplers, based on the self-imaging effect (SIE), are accepted popularly in integrated optics. According to the importance of MMI devices, in this paper, we present a novel method to design and fabricate MMI couplers. A technology of maskless lithography to make MMI couplers based on a smart digital micro-mirror device (DMD) system is proposed. A 1×4 MMI device is designed as an example, which shows the present method is efficient and cost-effective.

  5. Data management for digital mock-up visualization in immersive virtuel environment: application to car design

    Paillot , Damien

    2004-01-01

    Virtual Reality techniques constitute new tools for the trades of the design of manufactured products and offer profits in term of innovation, time and of money. The industrial stake is the integration of these techniques in the product design process. These techniques must thus be interfaced with the various trade associations and be able to be in phase with the flow of the digital models updates. The technological problems relate to the management of the geometrical data produced by the eng...

  6. Using/designing Digital Technologies Of Representation In Aboriginal Australian Knowledge Practices

    Helen Verran

    2007-01-01

    Full Text Available Indigenous Australians are often keen to use digital technologies in their struggle to develop sustainable livelihoods on their own lands. This paper tells of gradually coming to recognize how an Aboriginal Australian elder struggled against the grain of digital technologies designed to represent, in using them in Aboriginal Australian knowledge practices where knowledge is always actively performative rather than representional. The performance of Aboriginal knowledge must express the remaking of an ancestral reality. At the same time, this man exploited possibilities the technologies offered for representation in achieving political ends in dealing with representatives of mainstream Australia.

  7. A Design and Research on Protection of Architectural Heritage Based on Digital Technology

    Hou Shuang Qing

    2016-01-01

    Full Text Available In the era of digital information, how to reasonably use new-tech and idea for the architectural heritage protection remains urgent. In terms of digital protection, 3D laser scanning technology can perfectly remedy the manual measurement limitation thus correctly obtaining the relevant data. Via analysis, we find that the architectural heritage bears in itself the parameterized characteristic. As Building Information Modeling (BIM can help realize the parametric design, we proposed a feasible Architectural Heritage Information Model with the BIM “family” connecting architectural heritage and BIM. Finally, the parameter-induced graphic driving is achieved based on the relation between the two.

  8. On Digital Citizenship and Data as a New Commons: Can We Design a New Movement?

    Mulder, Ingrid; Jaskiewicz, Tomasz; Morelli, Nicola

    2019-01-01

    Along with the urgent need to reinvent our society, a series of paradigm shifts are already shaping transitions toward a more participatory and digital society. The current work takes stock of the promise of open data as a new resource and elaborates upon the maker movement, which has spurred...... people’s capacity to participate and has provided tools and infrastructures to unleash people’s intrinsic ability to create and innovate. We explore how open data can be a new commons, discuss how hackathons can support digital citizenship, and reflect on the role of Transition Design in creating...

  9. Efficient design of two-dimensional recursive digital filters. Final report

    Twogood, R.E.; Mitra, S.K.

    1980-01-01

    This report outlines the research progress during the period August 1978 to July 1979. This work can be divided into seven basic project areas. Project 1 deals with a comparative study of 2-D recursive and nonrecursive digital filters. The second project addresses a new design technique for 2-D half-plane recursive filters, and Projects 3 thru 5 deal with implementation issues. The sixth project presents our recent study of the applicability of array processors to 2-D digital signal processing. The final project involves our investigation into techniques for incorporating symmetry constraints on 2-D recursive filters in order to yield more efficient implementations

  10. Design of the ILC Prototype FONT4 Digital Intra-Train Beam-Based Feedback System

    Burrows, P.; Queen Mary, U. of London; Christian, G.B.; Hartin, A.F.; Dabiri Khah, H.; White, G.R.; Oxford U.; Clarke, C.C.; Perry, C.; Oxford Instruments; Kalinin, A.; Daresbury; McCormick, D.J.; Molloy, S.; Ross, M.C.; SLAC

    2007-01-01

    We present the design of the FONT4 digital intra-train beam position feedback system prototype and preliminary results of initial beam tests at the Accelerator Test Facility (ATF) at KEK. The feedback system incorporates a fast analogue beam position monitor (BPM) front-end signal processor, a digital feedback board, and a kicker driver amplifier. The short bunchtrain, comprising 3 electron bunches separated by c. 150ns, in the ATF extraction line was used to test components of the prototype feedback system

  11. Equalization of Loudspeaker and Room Responses Using Kautz Filters: Direct Least Squares Design

    Karjalainen Matti

    2007-01-01

    Full Text Available DSP-based correction of loudspeaker and room responses is becoming an important part of improving sound reproduction. Such response equalization (EQ is based on using a digital filter in cascade with the reproduction channel to counteract the response errors introduced by loudspeakers and room acoustics. Several FIR and IIR filter design techniques have been proposed for equalization purposes. In this paper we investigate Kautz filters, an interesting class of IIR filters, from the point of view of direct least squares EQ design. Kautz filters can be seen as generalizations of FIR filters and their frequency-warped counterparts. They provide a flexible means to obtain desired frequency resolution behavior, which allows low filter orders even for complex corrections. Kautz filters have also the desirable property to avoid inverting dips in transfer function to sharp and long-ringing resonances in the equalizer. Furthermore, the direct least squares design is applicable to nonminimum-phase EQ design and allows using a desired target response. The proposed method is demonstrated by case examples with measured and synthetic loudspeaker and room responses.

  12. Digital VLSI systems design a design manual for implementation of projects on FPGAs and ASICs using Verilog

    Ramachandran, S

    2007-01-01

    Digital VLSI Systems Design is written for an advanced level course using Verilog and is meant for undergraduates, graduates and research scholars of Electrical, Electronics, Embedded Systems, Computer Engineering and interdisciplinary departments such as Bio Medical, Mechanical, Information Technology, Physics, etc. It serves as a reference design manual for practicing engineers and researchers as well. Diligent freelance readers and consultants may also start using this book with ease. The book presents new material and theory as well as synthesis of recent work with complete Project Designs

  13. Noise equalization for detection of microcalcification clusters in direct digital mammogram images.

    McLoughlin, K.J.; Bones, P.J.; Karssemeijer, N.

    2004-01-01

    Equalizing image noise is shown to be an important step in the automatic detection of microcalcifications in digital mammography. This study extends a well established film-screen noise equalization scheme developed by Veldkamp et al. for application to full-field digital mammogram (FFDM) images. A

  14. Hardware/software co-design and optimization for cyberphysical integration in digital microfluidic biochips

    Luo, Yan; Ho, Tsung-Yi

    2015-01-01

    This book describes a comprehensive framework for hardware/software co-design, optimization, and use of robust, low-cost, and cyberphysical digital microfluidic systems. Readers with a background in electronic design automation will find this book to be a valuable reference for leveraging conventional VLSI CAD techniques for emerging technologies, e.g., biochips or bioMEMS. Readers from the circuit/system design community will benefit from methods presented to extend design and testing techniques from microelectronics to mixed-technology microsystems. For readers from the microfluidics domain,

  15. Digital mental health and intellectual disabilities: state of the evidence and future directions.

    Sheehan, Rory; Hassiotis, Angela

    2017-11-01

    The use of digital technologies in the management of mental illness, and more generally in the promotion of well-being and mental health, has received much recent attention and is a focus of current health policy. We conducted a narrative review to explore the opportunities and risks of digital technologies in mental healthcare specifically for people with intellectual disability, a sometimes marginalised and socially excluded group. The scope of digital mental health is vast and the promise of cheaper and more effective interventions delivered digitally is attractive. People with intellectual disability experience high rates of mental illness and could benefit from the development of novel therapies, yet seem to have been relatively neglected in the discourse around digital mental health and are often excluded from the development and implementation of new interventions. People with intellectual disability encounter several barriers to fully embracing digital technology, which may be overcome with appropriate support and adaptations. A small, but growing, literature attests to the value of incorporating digital technologies into the lives of people with intellectual disability, not only for promoting health but also for enhancing educational, vocational and leisure opportunities. Clearly further evidence is needed to establish the safety and clinical efficacy of digital mental health interventions for people with and without intellectual disability. A digital inclusion strategy that explicitly addresses the needs of people with intellectual disability would ensure that all can share the benefits of the digital world. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2017. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  16. Energy-efficient digital and wireless IC design for wireless smart sensing

    Zhou, Jun; Huang, Xiongchuan; Wang, Chao; Tae-Hyoung Kim, Tony; Lian, Yong

    2017-10-01

    Wireless smart sensing is now widely used in various applications such as health monitoring and structural monitoring. In conventional wireless sensor nodes, significant power is consumed in wirelessly transmitting the raw data. Smart sensing adds local intelligence to the sensor node and reduces the amount of wireless data transmission via on-node digital signal processing. While the total power consumption is reduced compared to conventional wireless sensing, the power consumption of the digital processing becomes as dominant as wireless data transmission. This paper reviews the state-of-the-art energy-efficient digital and wireless IC design techniques for reducing the power consumption of the wireless smart sensor node to prolong battery life and enable self-powered applications.

  17. Digital Picture Production and Picture aesthetic Competency in It-didactic Design

    Rasmussen, Helle

    , that It and media are only used seldom by 21 % of teachers in Visual Arts and 7 % of teachers in this subject never use It and Media in these lessons. Art teachers – among others - also express the need for continuing education. (Ministeriet for Børn og Undervisning 2011). Since lessons in digital picture...... production have been a demand in Visual Arts in Danish schools for more than two decades, these conditions call for development of new didactic knowledge. Besides new genres and ways of using digital pictures and media continuously develop. (Sørensen 2002). This ought to be an incessant challenge...... subject Visual Arts – and crosswise of subjects in school. The overall research question has been: How can IT-didactic designs support lessons in production of complex meaning in digital pictures and increase the development of pupil’s picture aesthetic competences? By using the expression ‘complex...

  18. DESIGN AND DEVELOPMENT OF AUGMENTATIVE AND ALTERNATIVE DIGITAL HOME CONTROL INTERFACE

    Matteo Pastorino

    2013-05-01

    Full Text Available An inquiry of the National Statistics Institute of Spain shows that 74% of the Spanish population with disabilities suffers some kind of limitation performing Daily Basic Activities, while 1.39 million cannot perform them at all without the assistance of specialized personnel. Digital Home Systems could mitigate disabled people’s difficulties to carry out those activities, giving the opportunity to manage home appliances through a single control. Digital Home Systems have to provide specific and adapted control interfaces based on Augmentative and Alternative Communication languages in order to be an efficient solution to the problem and to allow most vulnerable groups of people with disabilities to reach the highest level of autonomy.  This paper describes a Digital Home Interface capable of adapting layouts, styles and contents to device capability, user preferences and appliances’ features; designed with a combination of web technologies, standard languages for abstract interface definition and AAC systems.

  19. Digital workflow for virtually designing and milling ceramic lithium disilicate veneers: a clinical report.

    Zandinejad, A; Lin, W S; Atarodi, M; Abdel-Azim, T; Metz, M J; Morton, D

    2015-01-01

    Laminate veneers have been routinely used to restore and enhance the appearance of natural dentition. The traditional pathway for fabricating veneers consisted of making conventional polyvinyl siloxane impressions, producing stone casts, and fabricating final porcelain prostheses on stone dies. Pressed ceramics have successfully been used for laminate veneer fabrication for several years. Recently, digital computer-aided design/computer-aided manufacturing scanning has become commercially available to make a digital impression that is sent electronically to a dental laboratory or a chairside milling machine. However, technology has been developed to allow digital data acquisition in conjunction with electronically transmitted data that enables virtual design of restorations and milling at a remote production center. Following the aforementioned workflow will provide the opportunity to fabricate a physical cast-free restoration. This new technique has been reported recently for all-ceramic IPS e.max full-coverage pressed-ceramic restorations. However, laminate veneers are very delicate and technique-sensitive restorations when compared with all-ceramic full-coverage ones made from the same material. Complete digital design and fabrication of multiple consecutive laminate veneers seems to be very challenging. This clinical report presents the digital workflow for the virtual design and fabrication of multiple laminate veneers in a patient for enhancing the esthetics of his maxillary anterior teeth. A step-by-step process is presented with a discussion of the advantages and disadvantages of this novel technique. Additionally, the use of lithium disilicate ceramic as the material of choice and the rationale for such a decision is discussed.

  20. The evaluation the magnitude radiation exposure dose rate in digital radiography room design

    Dwiyanto, Agung; Setia Budi, Wahyu; Hardiman, Gagoek

    2017-12-01

    This study discusses the dose rate in digital radiography room, buit according to meet the provisions of KEMENKES No.1014 / Menkes / SK / XI / 2008 and Regulation of BAPETEN No. 8 / 2011. The provisions primary concern of radiation safety, not comfort, by considering the space design. There are five aspects to consider in designing the space: functionality, comfort, security, movement activities and aesthetics. However provisions only met three aspects of the design, which are a function, security and movement activity. Therefore, it is necessary to evaluate digital radiography room in terms of its ability to control external radiation exposure to be safe and comfortable The dose rate is measured by the range of primary and secondary radiation in the observation points by using Surveymeter. All data are obtained by the preliminary survey prior to the study. Furthermore, the review of digital radiography room is done based on architectural design theory. The dose rate for recommended improvement room is recalculated using the same method as the actual room with the help of computer modeling. The result of dose rate calculation at the inner and outer part of digital radiography observation room shows that in-room dose for a week at each measuring point exceeds the allowable dose limit both for staff and public. During a week of observation, the outdoor dose at some measuring points exceeds the dose limit set by the KEMENKES No.1014 / Menkes / SK / XI / 2008 and Regulation BEPETEN No 8/2011. Meanwhile, the result of dose rate calculation in the inner and outer part of the improved digital radiography room can meet the applicable regulations better.

  1. Contradictory directionalities of digital learning technology and its implications for the scope of imaginable possibilities for collaborating

    Chimirri, Niklas Alexander

    Contradictory learning directionalities are immanent to digital learning technology: Any technology suggests a limited multiplicity of situated uses in a learning practice, of understandings of how to learn and of what learning should be about. Herewith any technology offers a scope of imaginable...... possibilities for acting through it. Sociomaterially maintained learning directionalities – among others through the intended uses of learning technology in educational arrangements – afford the enactment of a delimited ensemble of experiential modes, sensualities, epistemologies, knowledges, and future hopes....... Next to offering opportunities to expand the learners’ scope of possibilities for transforming these learning directionalities together, digital learning technology thus also promotes the taken for grantedness of particular understandings of (most often instrumental) learning. They may consequently...

  2. An Open-Source Tool Set Enabling Analog-Digital-Software Co-Design

    Michelle Collins

    2016-02-01

    Full Text Available This paper presents an analog-digital hardware-software co-design environment for simulating and programming reconfigurable systems. The tool simulates, designs, as well as enables experimental measurements after compiling to configurable systems in the same integrated design tool framework. High level software in Scilab/Xcos (open-source programs similar to MATLAB/Simulink that converts the high-level block description by the user to blif format (sci2blif, which acts as an input to the modified VPR tool, including the code v p r 2 s w c s , encoding the specific platform through specific architecture files, resulting in a targetable switch list on the resulting configurable analog–digital system. The resulting tool uses an analog and mixed-signal library of components, enabling users and future researchers access to the basic analog operations/computations that are possible.

  3. A minimax technique for time-domain design of preset digital equalizers using linear programming

    Vaughn, G. L.; Houts, R. C.

    1975-01-01

    A linear programming technique is presented for the design of a preset finite-impulse response (FIR) digital filter to equalize the intersymbol interference (ISI) present in a baseband channel with known impulse response. A minimax technique is used which minimizes the maximum absolute error between the actual received waveform and a specified raised-cosine waveform. Transversal and frequency-sampling FIR digital filters are compared as to the accuracy of the approximation, the resultant ISI and the transmitted energy required. The transversal designs typically have slightly better waveform accuracy for a given distortion; however, the frequency-sampling equalizer uses fewer multipliers and requires less transmitted energy. A restricted transversal design is shown to use the least number of multipliers at the cost of a significant increase in energy and loss of waveform accuracy at the receiver.

  4. Design wave estimation considering directional distribution of waves

    SanilKumar, V.; Deo, M.C

    .elsevier.com/locate/oceaneng Technical Note Design wave estimation considering directional distribution of waves V. Sanil Kumar a,C3 , M.C. Deo b a OceanEngineeringDivision,NationalInstituteofOceanography,Donapaula,Goa-403004,India b Civil... of Physical Oceanography Norway, Report method for the routine 18, 1020–1034. ocean waves. Division of No. UR-80-09, 187 p. analysis of pitch and roll Conference on Coastal Engineering, 1. ASCE, Taiwan, pp. 136–149. Deo, M.C., Burrows, R., 1986. Extreme wave...

  5. 5MW Direct Drive Wind Turbine Generator Design

    Zaidi, Arsalan; Senn, Lucile; Ortega, Iratxe

    2012-01-01

    A 5MW direct drive offshore wind turbine generator was studied and simulated using Vector Fields OPERA. This software allows calculation of the flux density, force, torque, and eddy currents in the machine at different rotor positions. Based on the data obtained from the model, initial assumptions...... for the suitable machine are listed and the modelling process presented. The model of the generator was improved by changing design parameters, e.g the position of the magnets or fitting additional I-Cores, and analyse the effect of it....

  6. Design and Exploitation Problems of Drill String in Directional Drilling

    Bednarz Stanislaw

    2004-09-01

    Full Text Available Drill string design for directional drilling requires accounting for a number of factors. First, types and expected values of loads should be determined. Then, elements of the drill string should be so selected as to enable realization of the plan at specified loads. Some of additional factors, e. g. purchase, exploitation cost, geological conditions in the bore-hole, washing of the bore-hole, stability, trajectory, rig parameters, accuracy of gauges, pumps parameters remain in conflict. Drill pipes are made of rolled pipes, upset and welded with tool joints to 9,5 m long; the shorter ones can be made of hot forged rods. Exploitation requirements, being a result of practical experience supported by theoretical and laboratory analyses should be a part of syllabuses of technical staff educational programs. Apart from designing the string, it is also vital to lower the risk of a drilling failure. The significance of these aspects seems to be unquestionable.

  7. The rise of digital direct-to-consumer advertising?: Comparison of direct-to-consumer advertising expenditure trends from publicly available data sources and global policy implications

    Mackey, Tim K.; Cuomo, Raphael E.; Liang, Bryan A.

    2015-01-01

    Background Pharmaceutical marketing is undergoing a major shift in the United States, in part due to new transparency regulations under the healthcare reform act. Changes in pharmaceutical marketing practices include a possible shift from more traditional forms of direct-to-consumer advertising towards emerging use of Internet-based DTCA (?eDTCA?) given the growing importance of digital health or ?eHealth.? Though legally allowed only in the U.S. and New Zealand, eDTCA poses novel regulatory ...

  8. Need for New Optimisation Strategies in CR and Direct Digital Radiography

    Busch, H.P.

    2000-01-01

    Digital imaging techniques such as Digital Image Intensifier Radiography and Digital Storage Phosphor (Selenium) Radiography are replacing conventional film-screen radiography more and more. The aim of this development is the extension of diagnostic capabilities and the reduction of side effects such as radiation dose. Conventional film-screen radiography and digital radiography are very different ways of imaging. For digital radiography specific post-processing is the link between imaging conditions and film documentation. Optimisation of the images includes new possibilities of post-processing and a broad range for variation of the dose. Especially in fluoroscopy, dose can be reduced significantly by new technical features like pulsed fluoroscopy. For digital radiography the European guidelines on quality criteria have to be applied to projection radiography, digital subtraction radiography and to fluoroscopy. Further work should lead to a definition of reference values for the dose and the image quality. This has to be done first for single exposures and fluoroscopic mode and secondly for diagnostic and interventional procedures. (author)

  9. Special Digital Monies: The Design of Alipay and WeChat Wallet for Mobile Payment Practices in China

    Kow , Yong ,; Gui , Xinning; Cheng , Waikuen

    2017-01-01

    Part 2: Social Media and Design Innovation; International audience; While research studies of digital and mobile payment systems in HCI have pointed out design opportunities situated within informal and nuanced mobile contexts, we have not yet understood how we can design digital monies to allow users to use monies more easily in these contexts. In this study, we examined the design of Alipay and WeChat Wallet, two successful mobile payment apps in China, which have been used by Chinese users...

  10. Human Factors Guidance for Control Room and Digital Human-System Interface Design and Modification, Guidelines for Planning, Specification, Design, Licensing, Implementation, Training, Operation and Maintenance

    R. Fink, D. Hill, J. O' Hara

    2004-11-30

    Nuclear plant operators face a significant challenge designing and modifying control rooms. This report provides guidance on planning, designing, implementing and operating modernized control rooms and digital human-system interfaces.

  11. Human Factors Guidance for Control Room and Digital Human-System Interface Design and Modification. Guidelines for Planning, Specification, Design, Licensing, Implementation, Training, Operation and Maintenance

    Fink, R.; Hill, D.; O'Hara, J.

    2004-01-01

    Nuclear plant operators face a significant challenge designing and modifying control rooms. This report provides guidance on planning, designing, implementing and operating modernized control rooms and digital human-system interfaces

  12. Assessing Digital Student Productions, a Design-Based Research Study on the Development of a Criteria-Based Assessment Tool for Students’ Digital Multimodal Productions

    Hoffmeyer, Mikkeline; Jensen, Jesper Juellund; Olsen, Marie Veisegaard

    2017-01-01

    Digital multimodal production is becoming increasingly important as a 21st century skill and as a learning condition in school (K-12). Moreover, there is a growing attention to the significance of criteria-based assessment for learning. Nevertheless, assessment of students’ digital multimodal...... productions is often vague or lacking. Therefore, the research project aims at developing a tool to support assessment of student’s digital multimodal productions through a design-based research method. This paper presents a proposal for issues to be considered through a prototyping phase, based on interviews...

  13. Research on Digital Forensic Readiness Design in a Cloud Computing-Based Smart Work Environment

    Sangho Park

    2018-04-01

    Full Text Available Recently, the work environments of organizations have been in the process of transitioning into smart work environments by applying cloud computing technology in the existing work environment. The smart work environment has the characteristic of being able to access information assets inside the company from outside the company through cloud computing technology, share information without restrictions on location by using mobile terminals, and provide a work environment where work can be conducted effectively in various locations and mobile environments. Thus, in the cloud computing-based smart work environment, changes are occurring in terms of security risks, such as an increase in the leakage risk of an organization’s information assets through mobile terminals which have a high risk of loss and theft and increase the hacking risk of wireless networks in mobile environments. According to these changes in security risk, the reactive digital forensic method, which investigates digital evidence after the occurrence of security incidents, appears to have a limit which has led to a rise in the necessity of proactive digital forensic approaches wherein security incidents can be addressed preemptively. Accordingly, in this research, we design a digital forensic readiness model at the level of preemptive prevention by considering changes in the cloud computing-based smart work environment. Firstly, we investigate previous research related to the cloud computing-based smart work environment and digital forensic readiness and analyze a total of 50 components of digital forensic readiness. In addition, through the analysis of the corresponding preceding research, we design seven detailed areas, namely, outside the organization environment, within the organization guideline, system information, terminal information, user information, usage information, and additional function. Then, we design a draft of the digital forensic readiness model in the cloud

  14. UV-visible digital imaging of split injection in a Gasoline Direct Injection engine

    Merola Simona Silvia

    2015-01-01

    Full Text Available Ever tighter limits on pollutant emissions and the need to improve energy conversion efficiency have made the application of gasoline direct injection (GDI feasible for a much wider scale of spark ignition engines. Changing the way fuel is delivered to the engine has thus provided increased flexibility but also challenges, such as higher particulate emissions. Therefore, alternative injection control strategies need to be investigated in order to obtain optimum performance and reduced environmental impact. In this study, experiments were carried out on a single-cylinder GDI optical engine fuelled with commercial gasoline in lean-burn conditions. The single-cylinder was equipped with the head of a commercial turbocharged engine with similar geometrical specifications (bore, stroke, compression ratio and wall guided fuel injection. Optical accessibility was ensured through a conventional elongated hollow Bowditch piston and an optical crown, accommodating a fused-silica window. Experimental tests were performed at fixed engine speed and injection pressure, whereas the injection timing and the number of injections were adjusted to investigate their influence on combustion and emissions. UV-visible digital imaging was applied in order to follow the combustion process, from ignition to the late combustion phase. All the optical data were correlated with thermodynamic analysis and measurements of exhaust emissions. Split injection strategies (i.e. two injections per cycle with respect to single injection increased combustion efficiency and stability thanks to an improvement of fuel air mixing. As a consequence, significant reduction in soot formation and exhaust emission with acceptable penalty in terms of HC and NOx were measured.

  15. Measurement of the optical density of packable composites: comparison between direct and indirect digital systems

    Graziottin Luiz Felipe Rodrigues

    2002-01-01

    Full Text Available The aim of this study was to measure the optical density of four packable composite resins with widths of 1, 2, 3 and 4 mm, by means of Digora® (direct and DentScan DentView® (indirect digital imaging systems, in order to compare both methods. Twenty acrylic plates, with the proposed thicknesses, were used, each one containing a sample of each resin. Each acrylic plate was radiographed three times, under a standardized technique. For the Digora® system, an optical plate was used under each resin sample, and, for the DentScan DentView® system, occlusal films were employed, totalizing 60 exposures for each system. Optical plates and films were scanned and three consecutive optical readouts were carried out, totalizing 1,440 readouts. The results were submitted to statistical analysis and revealed that the average optical density of the four resins always increased as thickness increased. Regarding the comparisons between the composite resins, in both analysis the resin with the greater optical density was SurefilTM followed by ProdigyTM Condensable, AlertTM and Solitaire®. The correlations between the results of Digora® and DentScan DentView® were significant for the different thicknesses and materials. The observed tendency is that as the values obtained with the Digora® system increase, so do the values obtained with DentScan DentView®. While thickness increased, the values of optical density in both Digora® and DentScan DentView® tended to approach each other. The Digora® system presented smaller amplitude between the results obtained in adjacent thicknesses.

  16. Extending Mind and Space: Embodying the Model of Design Process in Digital Era

    Ruly Darmawan

    2009-12-01

    Full Text Available The recent electronic or digital technology has changed the life of contemporary society. From here, a new variant of cultural form is born as a consequence of the intensification of technology usage in everyday activities. This situation is then ended up with the paradigm shift of society’s perceptions, experience, and consciousness in almost all aspect of life, including the spatial discourse. The discourse of spatiality in the digital era becomes significant as it also repositions the conventional human spatial experience and consciousness in everyday life. Furthermore, this new spatial discourse may also appear as an opportunity to determine the learning space in the digital era. This paper emphasizes the topic on the information technology development and its impact on the forming of technoculture. The discussion will then be continued to the spatial discourse in digital era and its contribution in rethinking the learning space, especially the space of design process in academic. Lastly, the paper formulates the hexagonal model as the alternative of expanding the conventional space of design process and learning.

  17. Conception and data transfer analysis of an open-source digital image archive designed for radiology

    Teichgraeber, U.K.M.; Lehmkuhl, L.; Harderer, A.; Emmel, D.; Ehrenstein, T.; Ricke, J.; Felix, R.

    2003-01-01

    Purpose: Implementation of a self-designed, web-based digital image archive incorporating the existing DICOM infrastructure to assure distribution of digital pictures and reports and to optimize work flow. Assessment after three years. Materials and methods: Open-source software was used to guarantee highest reliability and cost effectiveness. In view of rapidly increasing capacity and decreasing costs of hard discs (HDs), HDs were preferred over slower and expensive magneto-optical disk (MOD) or tape storage systems. The number of installed servers increased from one to 12. By installing HDs with increased capacities, the number of servers should be kept constant. Entry and access of data were analyzed over two 4-month periods (after 1.5 and 2 years of continuous operations). Results: Our digital image archive was found to be very reliable, cost effective and suitable for its designated tasks. As judged from the measured access volume, the average utilization of the system increased by 160%. In the period from January to April 2002, the users accessed 239.8 gigabyte of the stored 873.7 gigabyte image data (27%). The volume of the stored data added 20%, mainly due to an increase in cross-section imaging. Conclusion: The challenge of developing a digital image archive with limited financial resources resulted in a practicable and expandable solution. The utilization, number of active users and volume of transferred data have increased significantly. Our concept of utilizing HDs for image storage proved to be successful. (orig.) [de

  18. Investigation of Classification and Design Requirements for Digital Software for Advanced Research Reactors

    Park, Gee Young; Jung, H. S.; Ryu, J. S.; Park, C

    2005-06-15

    As the digital technology is being developed drastically, it is being applied to various industrial instrumentation and control (I and C) fields. In the nuclear power plants, I and C systems are also being installed by digital systems replacing their corresponding analog systems installed previously. There had been I and C systems constructed by analog technology especially for the reactor protection system in the research reactor HANARO. Parallel to the pace of the current trend for digital technology, it is desirable that all I and C systems including the safety critical and non-safety systems in an advanced research reactor is to be installed based on the computer based system. There are many attractable features in using digital systems against existing analog systems in that the digital system has a superior performance for a function and it is more flexible than the analog system. And any fruit gained from the newly developed digital technology can be easily incorporated into the existing digital system and hence, the performance improvement of a computer based system can be implemented conveniently and promptly. Moreover, the capability of high integrity in electronic circuits reduces the electronic components needed to construct the processing device and makes the electronic board simple, and this fact reveals that the hardware failure itself are unlikely to occur in the electronic device other than some electric problems. Balanced the fact mentioned above are the roles and related issues of the software loaded on the digital integrated hardware. Some defects in the course of software development might induce a severe damage on the computer system and plant systems and therefore it is obvious that comprehensive and deep considerations are to be placed on the development of the software in the design of I and C system for use in an advanced research reactor. The work investigates the domestic and international standards on the classifications of digital

  19. Organization of project works in Industry 4.0 digital item designing companies

    Gurjanov, A. V.; Zakoldaev, D. A.; Shukalov, A. V.; Zharinov, I. O.

    2018-05-01

    The task of the project works organization in the Industry 4.0 item designing digital factories is being studied. There is a scheme of the item designing component life cycle. There is also a scheme how to develop and confirm the quality of the item designing component documentation using the mathematical modelling. There is a description of the self-organization principles for the cyber and physical technological equipment in the Industry 4.0 «smart factory» company during the manufacturing process.

  20. The effects of advanced digital signal processing concepts on VLSIC/VHSIC design

    Jankowski, C.

    Implementations of sophisticated mathematical techniques in advanced digital signal processors can significantly improve performance. Future VLSI and VHSI circuit designs must include the practical realization of these algorithms. A structured design approach is described and illustrated with examples from a RNS FIR filter processor development project. The CAE hardware and software required to support tasks of this complexity are also discussed. An EWS is recommended for controlling essential functions such as logic optimization, simulation and verification. The total IC design system is illustrated with the implementation of a new high performance algorithm for computing complex magnitude.

  1. Concept of Advanced Back-up Control Panel Design of Digital Main Control Room

    Jiang, Guo Jin; Sun, Yong Bin; Tan, Ke; Zhang, Li Ming; Shi, Ji; Zhang, Xue Gang; Huang, Wei Jun; Mao, Ting; Liu Yanzi

    2011-01-01

    Back-up control panel (BCP) of digital main control room (DMCR) is the backup means for main computerized control means (MCM). This paper focus on technical issues for advanced design of Backup Panel (BCP) for CPR1000 using qualified computer-based video display unit to display plant process indication and alarms. HFE issues also have been considered in the BCP design. Then, mean to fulfill safety target of NPP, best ergonomic effect has been described. At last conclusion on advanced BCP design is provided

  2. Designing Inclusive Reflective Learning with Digital Democratic Dialogue Across Boundaries and Diversities

    Sorensen, Elsebeth Korsgaard; Brooks, Eva Irene

    2018-01-01

    and structuring the “walls” of a digital learning architecture condusive to the establishment of a social, inclusive, empowering and interactive learning climate online. It makes a plea for using an approach of dialogic design with meta-structures in the communicative fora in order to promote inclusiveness......This paper deals with the challenge of designing online learning architectures for master students. From different theoretical concepts and with a netnographic methodological research approach, the paper discusses theoretical concepts, challenges and mechanisms significant to designing...

  3. Bridging the Gap between Actors and Digital tools in a Furnishing Design Process

    Rasmussen, Mai; Gade, Anne Nørkjær; Jensen, Rasmus Lund

    2017-01-01

    The high level of complexity in today’s building design requires a high level of interdisciplinary collaboration, which historically is an uncommon working method in the building industry. To support the interdisciplinary collaboration, new digital tools such as Building Information Models (BIM......) and Virtual Reality (VR) can be implemented in various phases of the building project. The implementation of BIM is expected to support the designers and improve the collaboration among multiple actors, but the social aspects related to the use of BIM in the design process needs further investigation...

  4. Concept of Advanced Back-up Control Panel Design of Digital Main Control Room

    Jiang, Guo Jin; Sun, Yong Bin; Tan, Ke; Zhang, Li Ming; Shi, Ji; Zhang, Xue Gang; Huang, Wei Jun; Mao, Ting; Liu Yanzi [China Nuclear Power Engineering Company, Shenzen (China)

    2011-08-15

    Back-up control panel (BCP) of digital main control room (DMCR) is the backup means for main computerized control means (MCM). This paper focus on technical issues for advanced design of Backup Panel (BCP) for CPR1000 using qualified computer-based video display unit to display plant process indication and alarms. HFE issues also have been considered in the BCP design. Then, mean to fulfill safety target of NPP, best ergonomic effect has been described. At last conclusion on advanced BCP design is provided.

  5. Design and Development of Intelligent Electrodes for Future Digital Health Monitoring: A Review

    Khairuddin, A. M.; Azir, K. N. F. Ku; Kan, P. Eh

    2018-03-01

    Electrodes are sensors used in electrocardiography (ECG) monitoring system to diagnose heart diseases. Over the years, diverse types of electrodes have been designed and developed to improve ECG monitoring system. However, more recently, with the technological advances and capabilities from the Internet of Things (IoT), cloud computing and data analytics in personalized healthcare, researchers are attempting to design and develop more effective as well as flexible ECG devices by using intelligent electrodes. This paper reviews previous works on electrodes used in electrocardiography (ECG) monitoring devices to identify the key ftures for designing and developing intelligent electrodes in digital health monitoring devices.

  6. Determination of the size of X-ray tube focal spots: direct digitalization vs optical evaluation

    Furquim, Tania A.C.; Yanikian, Denise; Costa, Paulo R.

    1996-01-01

    A comparative study between standard techniques for evaluation of X-ray tubes focal spots and a newer one which uses digital resources for image acquisition is presented. Results from measurements by using both methods are presented

  7. Blind I/Q imbalance compensation technique for direct-conversion digital radio transceivers

    De Witt, JJ

    2009-05-01

    Full Text Available . Digital signal processing techniques have widely been proposed to compensate for these mixer imperfections. Of these techniques, the class of blind compensation techniques seems very attractive since no test signals are required. This paper presents a...

  8. MODEL-ORIENTED METHOD OF DESIGN IMPLEMENTATION WHEN CREATING DIGITAL FILTERS

    V. Levinskyi

    2016-12-01

    Full Text Available This article discusses the example of model-oriented method of design and development of digital low-pass filters (LPF for automatic control systems (ACS. Typically, high frequency noise and disturbance attenuation is carried out by analogue LPF. However, technical implementation of analogue filters higher than the second order arouse certain difficulties related with the need of precise passive components ratings selection (resistors, capacitors. If the noise and disturbances spectral composition is known, it is possible to build digital LPF with the Nyquist frequency greater than the maximum frequency in the noise spectrum. Such possibility has appeared because of cheap, energy-efficient, high-speed 32-bit microcontrollers market entry. They have analogue signals sampling rate of 30 kHz and above. The traditional approach using the “manual” method of filter parameters calculation, obtaining their recurrence expressions and further program implementation requires high qualification and a lot of time consumption from the developer. An alternative to this approach is the model-oriented method of design (MOMD in MatLab environment when in the one environment the design of digital LPF, verificaton of its performance as a part of the ACS, generation and compilation of program codes for selected microcontroller family take place. MOMD can also be used in the designs of bandpass and bandstop filters for adaptive control systems or systems of technical diagnostics. If during the commissioning or the operation of ACS there is a need in digital LPF parameters change then this operation can be performed within half an hour. MOMD technology allows to significantly reduce the time for developing a specific product without loss of quality in its design ‘cause of extensive possibilities of MatLab development environment.

  9. Novel Design of Recursive Differentiator Based on Lattice Wave Digital Filter

    R. Barsainya

    2017-04-01

    Full Text Available In this paper, a novel design of third and fifth order differentiator based on lattice wave digital filter (LWDF, established on optimizing L_1-error approximation function using cuckoo search algorithm (CSA is proposed. We present a novel realization of minimum multiplier differentiator using LWD structure leading to requirement of optimizing only N coefficients for Nth order differentiator. The gamma coefficients of lattice wave digital differentiator (LWDD are computed by minimizing the L_1-norm fitness function leading to a flat response. The superiority of the proposed LWDD is evident by comparing it with other differentiators mentioned in the literature. The magnitude response of the designed LWDD is found to be of high accuracy with flat response in a wide frequency range. The simulation and statistical results validates that the designed minimum multiplier LWDD circumvents the existing one in terms of minimum absolute magnitude error, mean relative error (dB and efficient structural realization, thereby making the proposed LWDD a promising approach to digital differentiator design.

  10. Design of efficient circularly symmetric two-dimensional variable digital FIR filters.

    Bindima, Thayyil; Elias, Elizabeth

    2016-05-01

    Circularly symmetric two-dimensional (2D) finite impulse response (FIR) filters find extensive use in image and medical applications, especially for isotropic filtering. Moreover, the design and implementation of 2D digital filters with variable fractional delay and variable magnitude responses without redesigning the filter has become a crucial topic of interest due to its significance in low-cost applications. Recently the design using fixed word length coefficients has gained importance due to the replacement of multipliers by shifters and adders, which reduces the hardware complexity. Among the various approaches to 2D design, transforming a one-dimensional (1D) filter to 2D by transformation, is reported to be an efficient technique. In this paper, 1D variable digital filters (VDFs) with tunable cut-off frequencies are designed using Farrow structure based interpolation approach, and the sub-filter coefficients in the Farrow structure are made multiplier-less using canonic signed digit (CSD) representation. The resulting performance degradation in the filters is overcome by using artificial bee colony (ABC) optimization. Finally, the optimized 1D VDFs are mapped to 2D using generalized McClellan transformation resulting in low complexity, circularly symmetric 2D VDFs with real-time tunability.

  11. A new greedy search method for the design of digital IIR filter

    Ranjit Kaur

    2015-07-01

    Full Text Available A new greedy search method is applied in this paper to design the optimal digital infinite impulse response (IIR filter. The greedy search method is based on binary successive approximation (BSA and evolutionary search (ES. The suggested greedy search method optimizes the magnitude response and the phase response simultaneously and also finds the lowest order of the filter. The order of the filter is controlled by a control gene whose value is also optimized along with the filter coefficients to obtain optimum order of designed IIR filter. The stability constraints of IIR filter are taken care of during the design procedure. To determine the trade-off relationship between conflicting objectives in the non-inferior domain, the weighting method is exploited. The proposed approach is effectively applied to solve the multiobjective optimization problems of designing the digital low-pass (LP, high-pass (HP, bandpass (BP, and bandstop (BS filters. It has been demonstrated that this technique not only fulfills all types of filter performance requirements, but also the lowest order of the filter can be found. The computational experiments show that the proposed approach gives better digital IIR filters than the existing evolutionary algorithm (EA based methods.

  12. Design of a digital beam attenuation system for computed tomography: Part I. System design and simulation framework

    Szczykutowicz, Timothy P.; Mistretta, Charles A.

    2013-01-01

    Purpose: The purpose of this work is to introduce a new device that allows for patient-specific imaging-dose modulation in conventional and cone-beam CT. The device is called a digital beam attenuator (DBA). The DBA modulates an x-ray beam by varying the attenuation of a set of attenuating wedge filters across the fan angle. The ability to modulate the imaging dose across the fan beam represents another stride in the direction of personalized medicine. With the DBA, imaging dose can be tailored for a given patient anatomy, or even tailored to provide signal-to-noise ratio enhancement within a region of interest. This modulation enables decreases in: dose, scatter, detector dynamic range requirements, and noise nonuniformities. In addition to introducing the DBA, the simulation framework used to study the DBA under different configurations is presented. Finally, a detailed study on the choice of the material used to build the DBA is presented. Methods: To change the attenuator thickness, the authors propose to use an overlapping wedge design. In this design, for each wedge pair, one wedge is held stationary and another wedge is moved over the stationary wedge. The composite thickness of the two wedges changes as a function of the amount of overlap between the wedges. To validate the DBA concept and study design changes, a simulation environment was constructed. The environment allows for changes to system geometry, different source spectra, DBA wedge design modifications, and supports both voxelized and analytic phantom models. A study of all the elements from atomic number 1 to 92 were evaluated for use as DBA filter material. The amount of dynamic range and tube loading for each element were calculated for various DBA designs. Tube loading was calculated by comparing the attenuation of the DBA at its minimum attenuation position to a filtered non-DBA acquisition. Results: The design and parametrization of DBA implemented FFMCT has been introduced. A simulation

  13. Simulink-aided Design and Implementation of Sensorless BLDC Motor Digital Control System

    Zhilenkov, A. A.; Tsvetkov, Y. N.; Chistov, V. B.; Nyrkov, A. P.; Sokolov, S. S.

    2017-07-01

    The paper describes the process of creating of brushless direct current motor’s digital control system. The target motor has no speed sensor, so back-EMF method is used for commutation control. Authors show how to model the control system in MatLab/Simulink and to test it onboard STM32F4 microcontroller.This technology allows to create the most flexible system, which will control possible with a personal computer by communication lines. It is possible to examine the signals in the circuit of the actuator without any external measuring instruments - testers, oscilloscopes, etc. - and output waveforms and measured values of signals directly on the host PC.

  14. Design method for marine direct drive volume control ahead actuator

    WANG Haiyang

    2018-02-01

    Full Text Available [Objectives] In order to reduce the size, weight and auxiliary system configuration of marine ahead actuators, this paper proposes a kind of direct drive volume control electro-hydraulic servo ahead actuator. [Methods] The protruding and indenting control of the servo oil cylinder are realized through the forward and reverse of the bidirectional working gear pump, and the flow matching valve implements the self-locking of the ahead actuator in the target position. The mathematical model of the ahead actuator is established, and an integral separation fuzzy PID controller designed. On this basis, using AMESim software to build a simulation model of the ahead actuator, and combined with testing, this paper completes an analysis of the control strategy research and dynamic and static performance of the ahead actuator. [Results] The experimental results agree well with the simulation results and verify the feasibility of the ahead actuator's design. [Conclusions] The research results of this paper can provide valuable references for the integration and miniaturization design of marine ahead actuators.

  15. Synchronous Design and Test of Distributed Passive Radar Systems Based on Digital Broadcasting and Television

    Wan Xianrong

    2017-02-01

    Full Text Available Digital broadcasting and television are important classes of illuminators of opportunity for passive radars. Distributed and multistatic structure are the development trends for passive radars. Most modern digital broadcasting and television systems work on a network, which not only provides a natural condition to distributed passive radar but also puts forward higher requirements on the design of passive radar systems. Among those requirements, precise synchronization among the receivers and transmitters as well as among multiple receiving stations, which mainly involves frequency and time synchronization, is the first to be solved. To satisfy the synchronization requirements of distributed passive radars, a synchronization scheme based on GPS is presented in this paper. Moreover, an effective scheme based on the China Mobile Multimedia Broadcasting signal is proposed to test the system synchronization performance. Finally, the reliability of the synchronization design is verified via the distributed multistatic passive radar experiments.

  16. DIGITAL DETECTION SYSTEM DESIGN OF MYCOBACTERIUM TUBERCULOSIS THROUGH EXTRACTION OF SPUTUM IMAGE USING NEURAL NETWORK METHOD

    Franky Arisgraha

    2012-01-01

    Full Text Available Tuberculosis (TBC is an dangerous disease and many people has been infected. One of many important steps to control TBC effectively and efficiently is by increasing case finding using right method and accurate diagnostic. One of them is to detect Mycobacterium Tuberculosis inside sputum. Conventional detection of Mycobacterium Tuberculosis inside sputum can need a lot of time, so digitally detection method of Mycobacterium Tuberculosis was designed as an effort to get better result of detection. This method was designed by using combination between digital image processing method and Neural Network method. From testing report that was done, Mycobacterium can be detected with successful value reach 77.5% and training error less than 5%.

  17. Decorative design of ceramic tiles adapted to inkjet printing employing digital image processing

    Defez, B.; Santiago-Praderas, V.; Lluna, E.; Peris-Fajarnes, G.; Dunai, E.

    2013-01-01

    The ceramic tile sector is a very competitive industry. The designer's proficiency to offer new models of the decorated surface, adapted to the production means, plays a very important role in the competitiveness. In the present work, we analyze the evolution of the design process in the ceramic sector, as much as the changes experimented in parallel by the printing equipment. Afterwards, we present a new concept of ceramic design, based on digital image processing. This technique allows the generation of homogeneous and non-repetitive designs for large surfaces, especially thought for inkjet printing. With the programmed algorithms we have compiled a prototype software for the assistance of the ceramic design. This tool allows creating continuous designs for large surfaces saving developing time. (Author)

  18. Design of interstellar digital communication links: Some insights from communication engineering

    Messerschmitt, David G.; Morrison, Ian S.

    2012-09-01

    The design of an end-to-end digital interstellar communication system at radio frequencies is discussed, drawing on the disciplines of digital communication engineering and computer network engineering in terrestrial and near-space applications. One goal is a roadmap to the design of such systems, aimed at future designers of either receivers (SETI) or transmitters (METI). In particular we emphasize the implications arising from the impossibility of coordination between transmitter and receiver prior to a receiver's search for a signal. A system architecture based on layering, as commonly used in network and software design, assists in organizing and categorizing the various design issues and identifying dependencies. Implications of impairments introduced in the interstellar medium, such as dispersion, scattering, Doppler, noise, and signal attenuation are discussed. Less fundamental (but nevertheless influential) design issues are the motivations of the transmitter designers and associated resource requirements at both transmitter and receiver. Unreliability is inevitably imposed by non-idealities in the physical communication channel, and this unreliability will have substantial implications for those seeking to convey interstellar messages.

  19. Digital approach for the design of statistical analog data acquisition on SoCs

    Adao Antonio de Souza Junior

    2005-01-01

    With the current demand for mixed-signal SoCs, an increasing number of designers are looking for ADC architectures that can be easily implemented over digital substrates. Since ADC performance is strongly dependent upon physical and electrical features, it gets more difficult for them to benefit from more recent technologies, where these features are more variable. This way, analog signal acquisition is not allowed to follow an evolutionary trend compatible with Moore’s Law. In fact, such tre...

  20. In bits, bytes and stone:Making sense of digital afterlife, remembrance and heritage designs

    Sabra, Jakob Borrits; Andersen, Hans Jørgen

    2015-01-01

    The digital spheres of Information and Communication Technologies (ICT) and Social Network Services (SNS) are influencing 21st. century death. Today the dying and the bereaved attend mourning and remembrance both online and offline. Combined, the cemeteries, web memorials and social network sites constitute parts of an intricately weaved and interrelated network of practices dealing with death, mourning, memorialization and remembrance. Design pioneering company IDEO'S recent failed attempt t...

  1. Keeping Dublin Core Simple: Cross-Domain Discovery or Resource Description?; First Steps in an Information Commerce Economy: Digital Rights Management in the Emerging E-Book Environment; Interoperability: Digital Rights Management and the Emerging EBook Environment; Searching the Deep Web: Direct Query Engine Applications at the Department of Energy.

    Lagoze, Carl; Neylon, Eamonn; Mooney, Stephen; Warnick, Walter L.; Scott, R. L.; Spence, Karen J.; Johnson, Lorrie A.; Allen, Valerie S.; Lederman, Abe

    2001-01-01

    Includes four articles that discuss Dublin Core metadata, digital rights management and electronic books, including interoperability; and directed query engines, a type of search engine designed to access resources on the deep Web that is being used at the Department of Energy. (LRW)

  2. Design principles and issues of rights expression languages for digital rights management

    Wang, Xin

    2005-07-01

    Digital rights management (DRM) provides a unified approach to specifying, interpreting, enforcing and managing digital rights throughout the entire life cycle of digital assets. Using a declarative rights expression language (REL) for specifying rights and conditions in the form of licenses, as opposite to some other approaches (such as data structures and imperative languages), has been considered and adopted as a superior technology for implementing effective, interoperable and scalable DRM systems. This paper discusses some principles and issues for designing RELs, based on the experiences of developing a family of REL"s (DPRL, XrML 1.x, XrML 2.0 and MPEG REL). It starts with an overview of a family tree of the past and current REL"s, and their development history, followed by an analysis of their data models and a comparison with access-control oriented models. It then presents a number of primary design principles such as syntactic and semantic un-ambiguity, system interoperability, expressiveness in supporting business models and future extensibility, and discusses a number of key design issues such as maintaining stateful information, multi-tier issuance of rights, meta rights, identification of individual and aggregate objects, late-binding of to-beidentified entities, as well as some advanced ones on revocation and delegation of rights. The paper concludes with some remarks on REL profiling and extension for specific application domains.

  3. Design of secure digital communication systems using chaotic modulation, cryptography and chaotic synchronization

    Chien, T.-I.; Liao, T.-L.

    2005-01-01

    This paper presents a secure digital communication system based on chaotic modulation, cryptography, and chaotic synchronization techniques. The proposed system consists of a Chaotic Modulator (CM), a Chaotic Secure Transmitter (CST), a Chaotic Secure Receiver (CSR) and a Chaotic Demodulator (CDM). The CM module incorporates a chaotic system and a novel Chaotic Differential Peaks Keying (CDPK) modulation scheme to generate analog patterns corresponding to the input digital bits. The CST and CSR modules are designed such that a single scalar signal is transmitted in the public channel. Furthermore, by giving certain structural conditions of a particular class of chaotic system, the CST and the nonlinear observer-based CSR with an appropriate observer gain are constructed to synchronize with each other. These two slave systems are driven simultaneously by the transmitted signal and are designed to synchronize and generate appropriate cryptography keys for encryption and decryption purposes. In the CDM module, a nonlinear observer is designed to estimate the chaotic modulating system in the CM. A demodulation mechanism is then applied to decode the transmitted input digital bits. The effectiveness of the proposed scheme is demonstrated through the numerical simulation of an illustrative communication system. Synchronization between the chaotic circuits of the transmitter and receiver modules is guaranteed through the Lyapunov stability theorem. Finally, the security features of the proposed system in the event of attack by an intruder in either the time domain or the frequency domain are discussed

  4. Direct numerical methods of mathematical modeling in mechanical structural design

    Sahili, Jihad; Verchery, Georges; Ghaddar, Ahmad; Zoaeter, Mohamed

    2002-01-01

    Full text.Structural design and numerical methods are generally interactive; requiring optimization procedures as the structure is analyzed. This analysis leads to define some mathematical terms, as the stiffness matrix, which are resulting from the modeling and then used in numerical techniques during the dimensioning procedure. These techniques and many others involve the calculation of the generalized inverse of the stiffness matrix, called also the 'compliance matrix'. The aim of this paper is to introduce first, some different existing mathematical procedures, used to calculate the compliance matrix from the stiffness matrix, then apply direct numerical methods to solve the obtained system with the lowest computational time, and to compare the obtained results. The results show a big difference of the computational time between the different procedures

  5. Task based design of a digital work environment (DWE for an academic community

    Narayanan Meyyappan

    2002-01-01

    Full Text Available Task based design is considered one of the effective ways of designing functional software. It is generally accepted that tasks play an important role in system and user interface design. Identifying the user's tasks enables the designer to construct user interfaces reflecting the tasks' properties, including efficient usage patterns, easy-to-use interaction sequences, and powerful assistance features. In this paper, we present a prototype of a Digital Work Environment (DWE to support a task-oriented design to information access in a typical community of academic users. The resources in DWE are organized according to specific tasks performed by the research students and staff in the Division of Information Studies of Nanyang Technological University, Singapore. The tasks and resources were elicited based on the needs of faculty and students through interviews and focus groups. Examples of these tasks include preparation of a new course outline, setting of examination papers, preparation of reading lists and assignments, conducting literature reviews and writing dissertations. This paper discusses the problems of digital library users in an academic environment, highlights task oriented projects and focuses on the task of preparing and writing a Master dissertation. It highlights the importance of task based design in assisting and helping students and instructors from the time of selecting the research project to the time of submitting the final bound copies of the dissertation.

  6. Design an optimal controller for nuclear reactor using a digital computer

    Saleh, F.M.A.

    1986-01-01

    An attempt is carried out to design an optimal controller, for a model nuclear reactor at one hand, and a model nuclear power plant at another hand using a digital computer. The design philosophy adopted was to specify the system dynamics in terms of a desired system transfer function, and realizing the design synthesis through state-variable feedback technique, thus ensuring both stability and optimization in the state space sense. The control design was also tested by carrying out digital simulation transient response runs (step, ramp, impulse, etc.) and agreement between the predicted desirable response and actual response of the overall design was achieved. Furthermore the performance of the controller is verified against a reference non-linear model for purposes of assessing the accuracy of the linearized approximation model. The results show that state-variable feedback policy can rank as an effective optimal technique for designing control algorithm for an on-line computer of a nuclear power plant. 41 figs. 43 refs

  7. Design Information from the PSA for Digital Safety-Critical Systems

    Kang, Hyun Gook; Jang, Seung Cheol

    2005-01-01

    Many safety-critical applications such as nuclear field application usually adopt a similar design strategy for digital safety-critical systems. Their differences from the normal design for the non-safety-critical applications could be summarized as: multiple-redundancy, highly reliable components, strengthened monitoring mechanism, verified software, and automated test procedure. These items are focusing on maintaining the capability to perform the given safety function when it is requested. For the past several decades, probabilistic safety assessment (PSA) techniques are used in the nuclear industry to assess the relative effects of contributing events on plant risk and system reliability. They provide a unifying means of assessing physical faults, recovery processes, contributing effects, human actions, and other events that have a high degree of uncertainty. The applications of PSA provide not only the analysis results of already installed system but also the useful information for the system under design. The information could be derived from the PSA experience of the various safety-critical systems. Thanks to the design flexibility, the digital system is one of the most suitable candidates for risk-informed design (RID). In this article, we will describe the feedbacks for system design and try to develop a procedure for RID. Even though the procedure is not sophisticated enough now, it could be the start point of the further investigation for developing more complete and practical methodology

  8. Learning and Motivational Processes When Students Design Curriculum-Based Digital Learning Games

    Weitze, Charlotte Lærke

    2015-01-01

    This design-based research (DBR) project has developed an overall gamified learning design (big Game) to facilitate the learning process for adult students by inviting them to be their own learning designers through designing digital learning games (small games) in cross-disciplinary subject...... matters. The DBR project has investigated and experimented with which elements, methods, and processes are important when aiming at creating a cognitive complex (Anderson and Krathwohl, 2001) and motivating learning process within a reusable game-based learning design. This project took place in a co......, or programming provide a rich context for learning, since the construction of artefacts, in this case learning games, enables reflection and new ways of thinking. The students learned from reflection and interaction with the tools alone as well as in collaboration with peers. After analysing the students...

  9. Design of direct solar PV driven air conditioner

    Huang, Bin-Juine

    2015-12-05

    © 2015 Elsevier Ltd. Solar air conditioning system directly driven by stand-alone solar PV is studied. The air conditioning system will suffer from loss of power if the solar PV power generation is not high enough. It requires a proper system design to match the power consumption of air conditioning system with a proper PV size. Six solar air conditioners with different sizes of PV panel and air conditioners were built and tested outdoors to experimentally investigate the running probabilities of air conditioning at various solar irradiations. It is shown that the instantaneous operation probability (OPB) and the runtime fraction (RF) of the air conditioner are mainly affected by the design parameter rpL (ratio of maximum PV power to load power). The measured OPB is found to be greater than 0.98 at instantaneous solar irradiation IT > 600 W m-2 if rpL > 1.71 RF approaches 1.0 (the air conditioner is run in 100% with solar power) at daily-total solar radiation higher than 13 MJ m-2 day-1, if rpL > 3.

  10. The Effectiveness of Teaching Methods Used in Graphic Design Pedagogy in Both Analogue and Digital Education Systems

    Alhajri, Salman

    2016-01-01

    Purpose: this paper investigates the effectiveness of teaching methods used in graphic design pedagogy in both analogue and digital education systems. Methodology and approach: the paper is based on theoretical study using a qualitative, case study approach. Comparison between the digital teaching methods and traditional teaching methods was…

  11. Design, Implementation, and Lessons Learned from a Digital Storytelling Project in an Undergraduate Health Promotion Theory Course

    Rimando, Marylen; Smalley, K. Bryant; Warren, Jacob C.

    2015-01-01

    This article describes the design, implementation and lessons learned from a digital storytelling project in a health promotion theory course. From 2011-2012, 195 health promotion majors completed a digital storytelling project at a Midwestern university. The instructor observed students' understanding of theories and models. This article adds to…

  12. Optimizing digital elevation models (DEMs) accuracy for planning and design of mobile communication networks

    Hassan, Mahmoud A.

    2004-02-01

    Digital elevation models (DEMs) are important tools in the planning, design and maintenance of mobile communication networks. This research paper proposes a method for generating high accuracy DEMs based on SPOT satellite 1A stereo pair images, ground control points (GCP) and Erdas OrthoBASE Pro image processing software. DEMs with 0.2911 m mean error were achieved for the hilly and heavily populated city of Amman. The generated DEM was used to design a mobile communication network resulted in a minimum number of radio base transceiver stations, maximum number of covered regions and less than 2% of dead zones.

  13. Design and modernization of the control room with of the new digital I and C systems

    Fernandez, L. A.; Ortega, F.; Rejas, L.

    2011-01-01

    The use of the new digital I and c systems in the design of the new nuclear power plants, as well as the modernization of the existing ones, implies relevant changes in the control room design. New I and C systems provide new features that affect the control room operating concept, therefore a detailed analysis is required to take into consideration all the operating and human factor aspects. based on Tecnatom's experience, this article presents the methodological approach used as well as the most relevant aspects of this kind of project. (Author)

  14. Pre-service Physics Teachers Views on Designing and Developing Physics Digital Stories

    Kocakaya, Serhat; Karakoyun, Ferit; Kotluk, Nihat

    2016-01-01

    The aim of this study is to determine the pre-service physics teachers views on the effect of designing and developing physics digital stories (DST) on improving their 21st centuries skills. The study is a qualitative research carried out with 13 pre-service physics teachers, who participated in the course of designing and developing DST, during 6 weeks, at Yuzuncu Yil University, Turkey, in the spring term of 2013-2014 academic year. Data were collected using semi-structured interview...

  15. Digital VLSI design with Verilog a textbook from Silicon Valley Technical Institute

    Williams, John

    2008-01-01

    This unique textbook is structured as a step-by-step course of study along the lines of a VLSI IC design project. In a nominal schedule of 12 weeks, two days and about 10 hours per week, the entire verilog language is presented, from the basics to everything necessary for synthesis of an entire 70,000 transistor, full-duplex serializer - deserializer, including synthesizable PLLs. Digital VLSI Design With Verilog is all an engineer needs for in-depth understanding of the verilog language: Syntax, synthesis semantics, simulation, and test. Complete solutions for the 27 labs are provided on the

  16. The use of linear programming techniques to design optimal digital filters for pulse shaping and channel equalization

    Houts, R. C.; Burlage, D. W.

    1972-01-01

    A time domain technique is developed to design finite-duration impulse response digital filters using linear programming. Two related applications of this technique in data transmission systems are considered. The first is the design of pulse shaping digital filters to generate or detect signaling waveforms transmitted over bandlimited channels that are assumed to have ideal low pass or bandpass characteristics. The second is the design of digital filters to be used as preset equalizers in cascade with channels that have known impulse response characteristics. Example designs are presented which illustrate that excellent waveforms can be generated with frequency-sampling filters and the ease with which digital transversal filters can be designed for preset equalization.

  17. Preliminary design of an advanced programmable digital filter network for large passive acoustic ASW systems. [Parallel processor

    McWilliams, T.; Widdoes, Jr., L. C.; Wood, L.

    1976-09-30

    The design of an extremely high performance programmable digital filter of novel architecture, the LLL Programmable Digital Filter, is described. The digital filter is a high-performance multiprocessor having general purpose applicability and high programmability; it is extremely cost effective either in a uniprocessor or a multiprocessor configuration. The architecture and instruction set of the individual processor was optimized with regard to the multiple processor configuration. The optimal structure of a parallel processing system was determined for addressing the specific Navy application centering on the advanced digital filtering of passive acoustic ASW data of the type obtained from the SOSUS net. 148 figures. (RWR)

  18. The Art of Hardware Architecture Design Methods and Techniques for Digital Circuits

    Arora, Mohit

    2012-01-01

    This book highlights the complex issues, tasks and skills that must be mastered by an IP designer, in order to design an optimized and robust digital circuit to solve a problem. The techniques and methodologies described can serve as a bridge between specifications that are known to the designer and RTL code that is final outcome, reducing significantly the time it takes to convert initial ideas and concepts into right-first-time silicon.� Coverage focuses on real problems rather than theoretical concepts, with an emphasis on design techniques across various aspects of chip-design.�� Describes techniques to help IP designers get it right the first time, creating designs optimized in terms of power, area and performance; Focuses on practical aspects of chip design and minimizes theory; Covers chip design in a consistent way, starting with basics and gradually developing advanced concepts, such as electromagnetic compatibility (EMC) design techniques and low-power design techniques such as dynamic voltage...

  19. Diagnostic accuracy of artificially induced vertical root fractures: a comparison of direct digital periapical images with conventional periapical images

    Lee, Ji Un; Kwon, Ki Jeong; Koh, Kwang Joon

    2004-01-01

    To compare the diagnostic accuracy for the detection of root fractures in CMOS-based digital periapical images with conventional film-based periapical images. Sixty extracted single-root human teeth with closed apices were prepared endodontically and divided into two groups; artificially induced vertical root fracture group and control group. All radiographs were obtained using the paralleling technique. The radiographs were examined by 4 observers three times within a 4 week interval. Receiver operating characteristic (ROC) analysis was carried out using data obtained from four observers. Intra- and inter-examiner agreements were computed using kappa analysis. The area under the ROC curve (Az) was used as an indicator of the diagnostic accuracy of the imaging system. Az values were as follows: direct-digital images; 0.93, film-based images; 0.92, and inverted digital images; 0.91. There was no significant difference between imaging modalities(P<0.05). The kappa value of inter-observer agreement was 0.42(range:0.28-0.60) and intra-observer agreement was 0.57(range:0.44-0.75). There is no statistical difference in diagnostic accuracy for the detection of vertical root fractures between digital periapical images and conventional periapical images. The results indicate that the CMOS sensor is a good image detector for the evaluation of vertical root fractures.

  20. Design concepts for a nuclear digital instrumentation and control system platform

    Ou, T. C.; Chen, C. K.; Chen, P. J.; Shyu, S. S.; Lee, C. L.; Hsieh, S. F.

    2010-10-01

    The objective of this paper is to present the development results of the nuclear instrumentation and control system in Taiwan. As the Taiwan nuclear power plants age, the need to consider upgrading of both their safety and non-safety-related instrumentation and control systems becomes more urgent. Meanwhile, the digital instrumentation and control system that is based on current fast evolving electronic and information technologies are difficult to maintain effectively. Therefore, Institute of Nuclear Energy Research was made a decision to promote the Taiwan Nuclear Instrumentation and Control System project to collaborate with domestic electronic industry to establish self-reliant capabilities on the design, manufacturing, and application of nuclear instrumentation and control systems with newer technology. In the case of safety-related applications like nuclear instrumentation and control, safety-oriented quality control is required. In order to establish a generic qualified digital platform, the world-wide licensing experience should be considered in the licensing process. This paper describes the qualification and certification tools by IEC 61508 for design and development of safety related equipment and explains the basis for many decisions made while performing the digital upgrade. (Author)

  1. Sustainability Enhancement of a Turbine Vane Manufacturing Cell through Digital Simulation-Based Design

    Alessandra Caggiano

    2016-09-01

    Full Text Available Modern manufacturing systems should satisfy emerging needs related to sustainable development. The design of sustainable manufacturing systems can be valuably supported by simulation, traditionally employed mainly for time and cost reduction. In this paper, a multi-purpose digital simulation approach is proposed to deal with sustainable manufacturing systems design through Discrete Event Simulation (DES and 3D digital human modelling. DES models integrated with data on power consumption of the manufacturing equipment are utilized to simulate different scenarios with the aim to improve productivity as well as energy efficiency, avoiding resource and energy waste. 3D simulation based on digital human modelling is employed to assess human factors issues related to ergonomics and safety of manufacturing systems. The approach is implemented for the sustainability enhancement of a real manufacturing cell of the aerospace industry, automated by robotic deburring. Alternative scenarios are proposed and simulated, obtaining a significant improvement in terms of energy efficiency (−87% for the new deburring cell, and a reduction of energy consumption around −69% for the coordinate measuring machine, with high potential annual energy cost savings and increased energy efficiency. Moreover, the simulation-based ergonomic assessment of human operator postures allows 25% improvement of the workcell ergonomic index.

  2. Digital aesthetic forms between cinema and television: the need for new research directions

    Antonio Catolfi

    2013-03-01

    Full Text Available Twentieth century visual conventions — organized by a competitive collusion between cinema and television — did not survive the multiple forms and applications of digital media that put into play the multiplication of screens, the differentiation of production practices and processes of diffusion, and the rise of audience participative experiences.

  3. Design of full digital 50 kV electronic gun high voltage power supply

    Ge Lei; Shang Lei

    2014-01-01

    The design of full digital electronic gun high voltage power supply based on DSP was introduced in this paper. This power supply has innovations of full digital feedback circuit and PID closed-loop control mode. The application of high frequency resonant converter circuit reduces the size of the resonant element and transformer. The current-coupling distributed high voltage transformer and rectifier circuit were employed in this power supply. By this way, the power supply efficiency is improved and the number of distributed parameters is reduced, and the rectifier circuit could work under the oil-free environment. This power supply has been used in electronic grid-control high voltage system of the irradiation accelerator. (authors)

  4. Learning and Motivational Processes When Students Design Curriculum‐Based Digital Learning Games

    Weitze, Charlotte Lærke

    2016-01-01

    This design‐based research (DBR) project has developed an overall gamified learning design (big Game) to facilitate the learning process for adult students by inviting them to be their own learning designers through designing digital learning games (small games) in cross‐disciplinary subject...... matters. The DBR project has investigated and experimented with which elements, methods, and processes are important when aiming at creating a cognitive complex (Anderson and Krathwohl, 2001) and motivating learning process within a reusable game‐based learning design. This project took place in a co......, or programming provide a rich context for learning, since the construction of artefacts, in this case learning games, enables reflection and new ways of thinking. The students learned from reflection and interaction with the tools alone as well as in collaboration with peers. After analysing the students...

  5. Sustainable winter cities: Future directions for planning, policy and design

    Pressman, Norman E. P.

    Attempts to generate a "climate-responsive" northern urban form are part of a relatively recent phenomenon and field of investigation. In conjunction with the international "winter cities" movement, the need has been established for explicit, systematic inquiry directed toward national and local action to improve the comfort and lifestyles of all northern inhabitants. It is important to recognize that winter-induced discomforts exist and that they must be acknowledged in planning theory and practice. For northern cities to function more satisfactorily, the negative impacts of winter must be reduced while its beneficial characteristics are enhanced. While not all summer activities can or should be abandoned during winter, proper micro-climatic control is essential if human life is to be retained outside. The outdoor season should be extended since so much indoor isolation occurs. The main principles to be incorporated in exemplary "winter city" design should be contact with nature, year-round usability, user participation, cultural continuity, and the creation of comfortable micro-climatic conditions throughout much of the city's open spaces. All valuable sources of inspiration must be harnessed in the attempt to mediate between organic regionalism and internationalism, on the one hand, and romanticism and pragmatic realism, on the other. Creating optimum conditions for human well-being, habitation, work and intellectual development in each of the four seasons is vital under harsh environments. Adopting a climate-sensitive approach to planning policy and urban design can render everyday life less stressful, especially during the lengthy winter periods found in many northern latitude and high altitude settings.

  6. Twelve-bit 20-GHz reduced size pipeline accumulator in 0.25 μm SiGe:C technology for direct digital synthesiser applications

    Jensen, Brian Sveistrup; Khafaji, M. M.; Johansen, T. K.

    2012-01-01

    /Fmax of 180/220 GHz. The accumulator architecture omits the pre-skewing registers of the pipeline, thereby lowering both power consumption and circuit complexity. Some limitations to this design are discussed and the necessary equations for determining the phase jump encountered each time the control word...... (synthesised frequency) is changed are presented. For many applications employing signal processing after detection, this phase shift can then be corrected for. Compared to a full pipeline architecture (omitting the input circuitry for the most significant bit, as is customary for such designs......This article presents a 20 GHz, 12-bit pipeline accumulator with a reduced number of registers, suitable for direct digital synthesiser (DDS) applications. The accumulator is implemented in the IHP SG25H1 (0.25 μm) SiGe:C technology featuring heterojunction bipolar transistors (HBTs) with Ft...

  7. Design of an interactive digital nutritional education package for elderly people.

    Ali, Nazlena Mohamad; Shahar, Suzana; Kee, You Lee; Norizan, Azir Rezha; Noah, Shahrul Azman Mohd

    2012-12-01

    Designing a system for the elderly is crucial, as aging is associated with physiological changes that may impair perception, cognition and other social aspects; therefore, many aspects need consideration, especially in interface design. This study was conducted to develop a digital nutritional education package (WE Sihat) by following appropriate guidelines for elderly people to achieve better design interface and interaction. Touch-screen technology was used as a platform for user interaction. The nutritional content was based on previous nutrition studies and a lifestyle education package on healthy aging, which contains four modules. The questionnaires were distributed to 31 Malay subjects aged 60-76 years old, containing an evaluation about the overall content, graphics, design layout, colour, font size, audio/video, user-perceived satisfaction and acceptance levels. The findings showed positive feedback and acceptance. Most subjects agreed that the digital nutritional education package can increase their nutritional knowledge for a healthy lifestyle and is easy to use. The touch-screen technology was also well accepted by elderly people and can be used as a kiosk for disseminating nutrition education for healthy aging.

  8. A Digital Interface for the Part Designers and the Fixture Designers for a Reconfigurable Assembly System

    Vishwa V. Kumar

    2013-01-01

    Full Text Available This paper presents a web-based framework for interfacing product designers and fixture designers to fetch the benefits of early supplier involvement (ESI to a reconfigurable assembly system (RAS. The interfacing of the two members requires four steps, namely, collaboration chain, fixture supplier selection, knowledge share, and accommodation of service facilities so as to produce multiple products on a single assembly line. The interfacing not only provokes concurrency in the activities of product and fixture designer but also enables the assembly systems to tackle the spatial and generational variety. Among the four stages of interfacing, two steps are characterized by optimization issues, one from the product customer side and the other from the fixture designer side. To impart promptness in the optimization and hence the interaction, computationally economic tools are also presented in the paper for both of the supplier selection and fixture design optimization.

  9. Design and Implementation of a Video-Zoom Driven Digital Audio-Zoom System for Portable Digital Imaging Devices

    Park, Nam In; Kim, Seon Man; Kim, Hong Kook; Kim, Ji Woon; Kim, Myeong Bo; Yun, Su Won

    In this paper, we propose a video-zoom driven audio-zoom algorithm in order to provide audio zooming effects in accordance with the degree of video-zoom. The proposed algorithm is designed based on a super-directive beamformer operating with a 4-channel microphone system, in conjunction with a soft masking process that considers the phase differences between microphones. Thus, the audio-zoom processed signal is obtained by multiplying an audio gain derived from a video-zoom level by the masked signal. After all, a real-time audio-zoom system is implemented on an ARM-CORETEX-A8 having a clock speed of 600 MHz after different levels of optimization are performed such as algorithmic level, C-code, and memory optimizations. To evaluate the complexity of the proposed real-time audio-zoom system, test data whose length is 21.3 seconds long is sampled at 48 kHz. As a result, it is shown from the experiments that the processing time for the proposed audio-zoom system occupies 14.6% or less of the ARM clock cycles. It is also shown from the experimental results performed in a semi-anechoic chamber that the signal with the front direction can be amplified by approximately 10 dB compared to the other directions.

  10. Digital Game Violence and Direct Aggression in Adolescence: A Longitudinal Study of the Roles of Sex, Age, and Parent-Child Communication

    Wallenius, Marjut; Punamaki, Raija-Leena

    2008-01-01

    This study investigated the roles of sex, age, and parent-child communication in moderating the association between digital game violence and direct aggression in a two-year longitudinal study. Finnish 12- and 15-year-old adolescents (N = 316) participated in the follow-up survey. As hypothesized, digital game violence was linked to direct…

  11. Requirements on software lifecycle process (RSLP) for KALIMER digital computer-based MMIS design

    Lee, Jang Soo; Kwon, Kee Choon; Kim, Jang Yeol [Korea Atomic Energy Research Institute, Taejon (Korea)

    1998-04-01

    Digital Man Machine Interface System (MMIS) systems of Korea Advanced Liquid MEtal Reactor (KALIMER) may share code, data transmission, data, and process equipment to a greater degree than analog systems. Although this sharing is the basis for many of the advantages of digital systems, it also raises a key concern: a design using shared data or code has the potential to propagate a common-cause or common-mode failure via software errors, thus defeating the redundancy achieved by the hardware architectural structure. Greater sharing of process equipment among functions within a channel increases the consequences of the failure of a single hardware module and reduces the amount of diversity available within a single safety channel. The software safety plan describes the safety analysis implementation tasks that are to be carried out during the software life cycle. Documentation should exist that shows that the safety analysis activities have been successfully accomplished for each life cycle activity group. In particular, the documentation should show that the system safety requirement have been adequately addressed for each life cycle activity group, that no new hazards have been introduced, and that the software requirements, design elements, and code elements that can affect safety have been identified. Because the safety of software can be assured through both the process Verification and Validation (V and V) itself and the V and V of all the intermediate and final products during the software development lifecycle, the development of KALIMER Software Safety Framework (KSSF) must be established. As the first activity for establishing KSSF, we have developed this report, Requirement on Software Life-cycle Process (RSLP) for designing KALIMER digital MMIS. This report is organized as follows. Section I describes the background, definitions, and references of RSLP. Section II describes KALIMER safety software categorization. In Section III, we define the

  12. Designing, Prototyping and Evaluating Digital Mindfulness Applications: A Case Study of Mindful Breathing for Stress Reduction.

    Zhu, Bin; Hedman, Anders; Feng, Shuo; Li, Haibo; Osika, Walter

    2017-06-14

    During the past decade, there has been a rapid increase of interactive apps designed for health and well-being. Yet, little research has been published on developing frameworks for design and evaluation of digital mindfulness facilitating technologies. Moreover, many existing digital mindfulness applications are purely software based. There is room for further exploration and assessment of designs that make more use of physical qualities of artifacts. The study aimed to develop and test a new physical digital mindfulness prototype designed for stress reduction. In this case study, we designed, developed, and evaluated HU, a physical digital mindfulness prototype designed for stress reduction. In the first phase, we used vapor and light to support mindful breathing and invited 25 participants through snowball sampling to test HU. In the second phase, we added sonification. We deployed a package of probes such as photos, diaries, and cards to collect data from users who explored HU in their homes. Thereafter, we evaluated our installation using both self-assessed stress levels and heart rate (HR) and heart rate variability (HRV) measures in a pilot study, in order to measure stress resilience effects. After the experiment, we performed a semistructured interview to reflect on HU and investigate the design of digital mindfulness apps for stress reduction. The results of the first phase showed that 22 of 25 participants (88%) claimed vapor and light could be effective ways of promoting mindful breathing. Vapor could potentially support mindful breathing better than light (especially for mindfulness beginners). In addition, a majority of the participants mentioned sound as an alternative medium. In the second phase, we found that participants thought that HU could work well for stress reduction. We compared the effect of silent HU (using light and vapor without sound) and sonified HU on 5 participants. Subjective stress levels were statistically improved with both

  13. Access to digital library databases in higher education: design problems and infrastructural gaps.

    Oswal, Sushil K

    2014-01-01

    After defining accessibility and usability, the author offers a broad survey of the research studies on digital content databases which have thus far primarily depended on data drawn from studies conducted by sighted researchers with non-disabled users employing screen readers and low vision devices. This article aims at producing a detailed description of the difficulties confronted by blind screen reader users with online library databases which now hold most of the academic, peer-reviewed journal and periodical content essential for research and teaching in higher education. The approach taken here is borrowed from descriptive ethnography which allows the author to create a complete picture of the accessibility and usability problems faced by an experienced academic user of digital library databases and screen readers. The author provides a detailed analysis of the different aspects of accessibility issues in digital databases under several headers with a special focus on full-text PDF files. The author emphasizes that long-term studies with actual, blind screen reader users employing both qualitative and computerized research tools can yield meaningful data for the designers and developers to improve these databases to a level that they begin to provide an equal access to the blind.

  14. New Design for Rapid Prototyping of Digital Master Casts for Multiple Dental Implant Restorations.

    Romero, Luis; Jiménez, Mariano; Espinosa, María Del Mar; Domínguez, Manuel

    2015-01-01

    This study proposes the replacement of all the physical devices used in the manufacturing of conventional prostheses through the use of digital tools, such as 3D scanners, CAD design software, 3D implants files, rapid prototyping machines or reverse engineering software, in order to develop laboratory work models from which to finish coatings for dental prostheses. Different types of dental prosthetic structures are used, which were adjusted by a non-rotatory threaded fixing system. From a digital process, the relative positions of dental implants, soft tissue and adjacent teeth of edentulous or partially edentulous patients has been captured, and a maser working model which accurately replicates data relating to the patients oral cavity has been through treatment of three-dimensional digital data. Compared with the conventional master cast, the results show a significant cost savings in attachments, as well as an increase in the quality of reproduction and accuracy of the master cast, with the consequent reduction in the number of patient consultation visits. The combination of software and hardware three-dimensional tools allows the optimization of the planning of dental implant-supported rehabilitations protocol, improving the predictability of clinical treatments and the production cost savings of master casts for restorations upon implants.

  15. New Design for Rapid Prototyping of Digital Master Casts for Multiple Dental Implant Restorations.

    Luis Romero

    Full Text Available This study proposes the replacement of all the physical devices used in the manufacturing of conventional prostheses through the use of digital tools, such as 3D scanners, CAD design software, 3D implants files, rapid prototyping machines or reverse engineering software, in order to develop laboratory work models from which to finish coatings for dental prostheses. Different types of dental prosthetic structures are used, which were adjusted by a non-rotatory threaded fixing system.From a digital process, the relative positions of dental implants, soft tissue and adjacent teeth of edentulous or partially edentulous patients has been captured, and a maser working model which accurately replicates data relating to the patients oral cavity has been through treatment of three-dimensional digital data.Compared with the conventional master cast, the results show a significant cost savings in attachments, as well as an increase in the quality of reproduction and accuracy of the master cast, with the consequent reduction in the number of patient consultation visits. The combination of software and hardware three-dimensional tools allows the optimization of the planning of dental implant-supported rehabilitations protocol, improving the predictability of clinical treatments and the production cost savings of master casts for restorations upon implants.

  16. New Design for Rapid Prototyping of Digital Master Casts for Multiple Dental Implant Restorations

    Romero, Luis; Jiménez, Mariano; Espinosa, María del Mar; Domínguez, Manuel

    2015-01-01

    Aim This study proposes the replacement of all the physical devices used in the manufacturing of conventional prostheses through the use of digital tools, such as 3D scanners, CAD design software, 3D implants files, rapid prototyping machines or reverse engineering software, in order to develop laboratory work models from which to finish coatings for dental prostheses. Different types of dental prosthetic structures are used, which were adjusted by a non-rotatory threaded fixing system. Method From a digital process, the relative positions of dental implants, soft tissue and adjacent teeth of edentulous or partially edentulous patients has been captured, and a maser working model which accurately replicates data relating to the patients oral cavity has been through treatment of three-dimensional digital data. Results Compared with the conventional master cast, the results show a significant cost savings in attachments, as well as an increase in the quality of reproduction and accuracy of the master cast, with the consequent reduction in the number of patient consultation visits. The combination of software and hardware three-dimensional tools allows the optimization of the planning of dental implant-supported rehabilitations protocol, improving the predictability of clinical treatments and the production cost savings of master casts for restorations upon implants. PMID:26696528

  17. Design mobile satellite system architecture as an integral part of the cellular access digital network

    Chien, E. S. K.; Marinho, J. A.; Russell, J. E., Sr.

    1988-01-01

    The Cellular Access Digital Network (CADN) is the access vehicle through which cellular technology is brought into the mainstream of the evolving integrated telecommunications network. Beyond the integrated end-to-end digital access and per call network services provisioning of the Integrated Services Digital Network (ISDN), the CADN engenders the added capability of mobility freedom via wireless access. One key element of the CADN network architecture is the standard user to network interface that is independent of RF transmission technology. Since the Mobile Satellite System (MSS) is envisioned to not only complement but also enhance the capabilities of the terrestrial cellular telecommunications network, compatibility and interoperability between terrestrial cellular and mobile satellite systems are vitally important to provide an integrated moving telecommunications network of the future. From a network standpoint, there exist very strong commonalities between the terrestrial cellular system and the mobile satellite system. Therefore, the MSS architecture should be designed as an integral part of the CADN. This paper describes the concept of the CADN, the functional architecture of the MSS, and the user-network interface signaling protocols.

  18. Characterization and Design of Digital Pointing Subsystem for Optical Communication Demonstrator

    Racho, C.; Portillo, A.

    1998-01-01

    The Optical Communications Demonstrator (OCD) is a laboratory-based lasercom demonstration terminal designed to validate several key technologies, including beacon acquisition, high bandwidth tracking, precision bearn pointing, and point-ahead compensation functions. It has been under active development over the past few years. The instrument uses a CCD array detector for both spatial acquisition and high-bandwidth tracking, and a fiber coupled laser transmitter. The array detector tracking concept provides wide field-of-view acquisition and permits effective platform jitter compensation and point-ahead control using only one steering mirror. This paper describes the detailed design and characterization of the digital control loop system which includes the Fast Steering Mirror (FSM), the CCD image tracker, and the associated electronics. The objective is to improve the overall system performance using laboratory measured data. The. design of the digital control loop is based on a linear time invariant open loop model. The closed loop performance is predicted using the theoretical model. With the digital filter programmed into the OCD control software, data is collected to verify the predictions. This paper presents the results of the, system modeling and performance analysis. It has been shown that measurement data closely matches theoretical predictions. An important part of the laser communication experiment is the ability of FSM to track the laser beacon within the. required tolerances. The pointing must be maintained to an accuracy that is much smaller than the transmit signal beamwidth. For an earth orbit distance, the system must be able to track the receiving station to within a few microradians. The failure. to do so will result in a severely degraded system performance.

  19. A basic design of microcontroller based data processor and local display for digital logarithmic power channel

    Nur Khasan; Syahrudin Yusuf

    2009-01-01

    A data processor and its local display for a digital logarithmic power channel, which will be used as a complement and diversification of nuclear reactor instrument, has been designed using micro controller base circuit. This power channel has been designed using TTL device and microcontroller. The roll of the microcontroller will be as data acquisition, data processing for the measurement of percentage reactor power, period and the trip decision. In this design has beer; created display of numerical value will be display on the local display in on-line mode for 1 nV to 10 10 nV neutron flux measurement range. This logarithmic power channel is expected to support the existing instrument which uses analog system in Instrumentation and Control System of nuclear reactor. (author)

  20. A SystemC-Based Design Methodology for Digital Signal Processing Systems

    Christian Haubelt

    2007-03-01

    Full Text Available Digital signal processing algorithms are of big importance in many embedded systems. Due to complexity reasons and due to the restrictions imposed on the implementations, new design methodologies are needed. In this paper, we present a SystemC-based solution supporting automatic design space exploration, automatic performance evaluation, as well as automatic system generation for mixed hardware/software solutions mapped onto FPGA-based platforms. Our proposed hardware/software codesign approach is based on a SystemC-based library called SysteMoC that permits the expression of different models of computation well known in the domain of digital signal processing. It combines the advantages of executability and analyzability of many important models of computation that can be expressed in SysteMoC. We will use the example of an MPEG-4 decoder throughout this paper to introduce our novel methodology. Results from a five-dimensional design space exploration and from automatically mapping parts of the MPEG-4 decoder onto a Xilinx FPGA platform will demonstrate the effectiveness of our approach.

  1. Designing a digital pedagogical pattern for improving foreign language learners’ oral proficiency

    Carina Grobler

    2016-09-01

    Full Text Available South African undergraduate foreign language students need more opportunity to practise their oral language skills. Not only do appeals to focus more on oral productive skills feature in scholarly literature (Delena-le Roux 2010, it is also one of the main conclusions from a survey among beginner students of French at the Potchefstroom Campus of North-West University (South Africa. It was therefore necessary to design a teaching and learning intervention, specifically aimed at improving beginner students’ oral communication skills in French. Laurillard’s (2012 Conversational Framework inspired the design of a digital pedagogical pattern (DPP, consisting of context and pedagogy descriptors for the development of foreign language learners’ oral communication skills. The Conversational Framework analyses formal learning and challenges the use of new technologies in learning. The implementation process of a DPP for the development of students’ (French oral skills involved three cycles, each with specific outcomes and three groups of participants: the control group and two experimental groups. Field-testing the proposed DPP provided important insights which should be integrated in the design of subsequent digital pedagogical patterns in the specific context: limiting the participant groups to two; decreasing the number of interventions to be implemented in the limited teaching time of a semester; ensuring that each step adheres to the requirements of the Conversational Framework. Student results from the learning interventions in future studies should reveal which intervention better promotes oral communication skills.

  2. Design of two digital radiation tolerant integrated circuits for high energy physics experiments data readout

    Bonacini, Sandro

    2003-01-01

    High Energy Physics research (HEP) involves the design of readout electron- ics for its experiments, which generate a high radiation ¯eld in the detectors. The several integrated circuits placed in the future Large Hadron Collider (LHC) experiments' environment have to resist the radiation and carry out their normal operation. In this thesis I will describe in detail what, during my 10-months partic- ipation in the digital section of the Microelectronics group at CERN, I had the possibility to work on: - The design of a radiation-tolerant data readout digital integrated cir- cuit in a 0.25 ¹m CMOS technology, called \\the Kchip", for the CMS preshower front-end system. This will be described in Chapter 3. - The design of a radiation-tolerant SRAM integrated circuit in a 0.13 ¹m CMOS technology, for technology radiation testing purposes and fu- ture applications in the HEP ¯eld. The SRAM will be described in Chapter 4. All the work has carried out under the supervision and with the help of Dr. Kostas Klouki...

  3. Software life cycle process and classification guides for KNICS digital instrumentation and control system design

    Lee, Jang Soo; Son, Han Seung; Kim, Jang Yeol; Kwon, Kee Choon; Lee, Soon Seung; Kim, Doo Hwan [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2002-04-01

    Documentation should exist that shows that the qualification activities have been successfully accomplished for each life cycle activity group. In particular, the documentation should show that the system safety requirements have been adequately addressed for each life cycle activity group, that no new hazards have been introduced, and that the software requirements, design elements, and code elements that can affect safety have been identified. Because the safety of software can be assured through both the process Verification and Validation (V and V) itself and the V and V of all the intermediate and final products during the software development lifecycle, the development of KNICS Software Safety Framework (KSSF) must be established. As the first activity for establishing KSSF, we have developed this report, Software Life Cycle Process and Classification Guides for KNICS Digital I and C System. This report is organized as follows. Chapter I describes the background, definitions, and references of SLCP. Chapter II describes KNICS safety software categorization. In Chapter III, we define the requirements on software life cycle process for designing digital KNICS. Chapter III.3, that is the main section of the chapter, includes the requirements for software life cycle process planning, the requirements for software life cycle process implementation, and the requirements for software life cycle process design outputs. Finally, we have described the result of a case study on the SLCP for developing the software of ESF-CCS system that is being developed by a private company, BNF. 29 refs., 5 figs., 7 tabs. (Author)

  4. Digital Games, Design, and Learning: A Systematic Review and Meta-Analysis.

    Clark, Douglas B; Tanner-Smith, Emily E; Killingsworth, Stephen S

    2016-03-01

    In this meta-analysis, we systematically reviewed research on digital games and learning for K-16 students. We synthesized comparisons of game versus nongame conditions (i.e., media comparisons) and comparisons of augmented games versus standard game designs (i.e., value-added comparisons). We used random-effects meta-regression models with robust variance estimates to summarize overall effects and explore potential moderator effects. Results from media comparisons indicated that digital games significantly enhanced student learning relative to nongame conditions ([Formula: see text] = 0.33, 95% confidence interval [0.19, 0.48], k = 57, n = 209). Results from value-added comparisons indicated significant learning benefits associated with augmented game designs ([Formula: see text] = 0.34, 95% confidence interval [0.17, 0.51], k = 20, n = 40). Moderator analyses demonstrated that effects varied across various game mechanics characteristics, visual and narrative characteristics, and research quality characteristics. Taken together, the results highlight the affordances of games for learning as well as the key role of design beyond medium.

  5. A new paradigm in the design of energy-efficient digital circuits using laterally-actuated double-gate NEMS

    Dadgour, Hamed F.

    2010-01-01

    Nano-Electro-Mechanical Switches (NEMS) offer the prospect of improved energy-efficiency in digital circuits due to their near-zero subthreshold leakage and extremely low subthreshold swing values. Among the different approaches of implementing NEMS, laterallyactuated double-gate NEMS devices have attracted much attention as they provide unique and exciting circuit design opportunities. For instance, this paper demonstrates that compact XOR/XNOR gates can be implemented using only two such NEMS transistors. While this in itself is a major improvement, its implications for minimizing Boolean functions using Karnaugh maps (K-maps) are even more significant. In the standard K-map technique, which is used in digital circuit design, adjacent "1s" (minterms) are grouped only in horizontal and/or vertical directions; the diagonal (or zig-zag) grouping of adjacent "1s" is not an option due to the absence of compact XOR/XNOR gates. However, this work demonstrates, for the first time ever, that in lateral double-gate NEMS-based circuits, grouping of minterms is possible in horizontal and vertical as well as diagonal fashions. This is because the diagonal groupings of minterms require XOR/XNOR operations, which are available in such NEMS-based circuits at minimal costs. This novel design paradigm facilitates more compact implementations of Boolean functions and thus, considerably improves their energy-efficiency. For example, a lateral NEMS-based full-adder is implemented using less than half the number of transistors, which is required by a CMOS-based full-adder. Furthermore, circuit simulations are performed to evaluate the energy-efficiencies of the NEMS-based 32-bit carry-save adders compared to their standard CMOS-based counterparts. Copyright 2010 ACM.

  6. Accelerating Digital Mental Health Research From Early Design and Creation to Successful Implementation and Sustainment.

    Mohr, David C; Lyon, Aaron R; Lattie, Emily G; Reddy, Madhu; Schueller, Stephen M

    2017-05-10

    Mental health problems are common and pose a tremendous societal burden in terms of cost, morbidity, quality of life, and mortality. The great majority of people experience barriers that prevent access to treatment, aggravated by a lack of mental health specialists. Digital mental health is potentially useful in meeting the treatment needs of large numbers of people. A growing number of efficacy trials have shown strong outcomes for digital mental health treatments. Yet despite their positive findings, there are very few examples of successful implementations and many failures. Although the research-to-practice gap is not unique to digital mental health, the inclusion of technology poses unique challenges. We outline some of the reasons for this gap and propose a collection of methods that can result in sustainable digital mental health interventions. These methods draw from human-computer interaction and implementation science and are integrated into an Accelerated Creation-to-Sustainment (ACTS) model. The ACTS model uses an iterative process that includes 2 basic functions (design and evaluate) across 3 general phases (Create, Trial, and Sustain). The ultimate goal in using the ACTS model is to produce a functioning technology-enabled service (TES) that is sustainable in a real-world treatment setting. We emphasize the importance of the service component because evidence from both research and practice has suggested that human touch is a critical ingredient in the most efficacious and used digital mental health treatments. The Create phase results in at least a minimally viable TES and an implementation blueprint. The Trial phase requires evaluation of both effectiveness and implementation while allowing optimization and continuous quality improvement of the TES and implementation plan. Finally, the Sustainment phase involves the withdrawal of research or donor support, while leaving a functioning, continuously improving TES in place. The ACTS model is a step

  7. Development of processing procedure preparing for digital computer controlled equipment on modular design base

    Starosel'tsev, O.P.; Khrundin, V.I.

    1982-01-01

    In order to reduce labour consumption of technological preparation of production for digital computer controlled machines during the treatment of steam turbines articles created is a system of modular design of technological processes and controlling programs. A set of typical modulas-transitions, being a number of surfaces of an articles treated with one cutting tool in optimum sequence, and a library of cutting tools are the base of the system. Introduction of such a system sharply enhaneces the efficiency of the equipment utilization [ru

  8. The collaboration between and contribution of a digital open innovation platform to a local design process

    del Castillo, Jacqueline; Bhatti, Yasser; Hossain, Mokter

    2017-01-01

    We examine the potential of an open innovation digital platform to expose a local innovation process to a greater number of ideas and a more inclusive set of stakeholders. To do so we studied an online innovation challenge on the OpenIDEO to reimagine the end-of-life experience sponsored by Sutte...... it leads to a greater number of ideas from a wider and more inclusive set of stakeholders. We offer insights for the literatures on open innovation and design thinking in a healthcare context....

  9. Designing the future of talking therapy: Using digital health to improve outcomes in psychosis

    Amy Hardy

    2016-01-01

    A mobile app appears to be a feasible means of addressing barriers to access, uptake and adherence in talking therapies for psychosis, and may reduce costs and improve outcomes. Wellcome Trust funding has recently been obtained to investigate integrating wearable technology into the app, with the aim of increasing its sensitivity to user needs and further reducing processing demands. A Thinkthru digital platform is also being designed for use during therapy sessions and will be synchronised with the app. Further investigation of the platform and app’s potential to facilitate meaningful behaviour change is warranted, and a feasibility study and randomised controlled trial are planned.

  10. Design of integrated all optical digital to analog converter (DAC) using 2D photonic crystals

    Moniem, Tamer A.; El-Din, Eman S.

    2017-11-01

    A novel design of all optical 3 bit digital to analog (DAC) converter will be presented in this paper based on 2 Dimension photonic crystals (PhC). The proposed structure is based on the photonic crystal ring resonators (PCRR) with combining the nonlinear Kerr effect on the PCRR. The total size of the proposed optical 3 bit DAC is equal to 44 μm × 37 μm of 2D square lattice photonic crystals of silicon rods with refractive index equal to 3.4. The finite different time domain (FDTD) and Plane Wave Expansion (PWE) methods are used to back the overall operation of the proposed optical DAC.

  11. EnviroAtlas - Average Direct Normal Solar resources kWh/m2/Day by 12-Digit HUC for the Conterminous United States

    U.S. Environmental Protection Agency — The annual average direct normal solar resources by 12-Digit Hydrologic Unit (HUC) was estimated from maps produced by the National Renewable Energy Laboratory for...

  12. Design of microreactor by integration of reverse engineering and direct metal laser sintering process

    Bineli, Aulus Roberto Romao; Gimenez Perez, Ana Paula; Bernardes, Luiz Fernando; Munhoz, Andre Luiz Jardini; Maciel Filho, Rubens [Universidade de Campinas (LOPCA/UNICAMP), SP (Brazil). School of Chemical Engineering. Laboratory of Optimization, Design and Advanced Process Control], Email: aulus@feq.unicamp.br

    2010-07-01

    The propose of this work is to present high precision microfabrication facilities using computer aided technologies as Reverse Engineering (RE) and Rapid Manufacturing (RM) to analyze, design and construct micro reactors to produce high content hydrogen gas. Micro reactors are very compact, have a high surface to volume ratio, exhibit enhanced heat and mass transfer rates, denotes extremely low pressure drop and allow improved thermal integration in the processes involved. The main goals of micro reactors are the optimization of conventional chemical plants and low footprint, opening different ways to research new process technologies and synthesis of new products. In this work, a microchannels plate and housing structure of these plates were fabricated using DMLS method (Direct Metal Laser Sintering). The plates were analyzed to verify the minimum thickness wall that machine can produce, and the housing structure were digitalized, using a 3D scanning, to perform a 3D inspection and to verify the deflection of the constructed part in comparison with original CAD design models. It was observed that DMLS systems are able to produce micro reactors and microchannels plates with high precision at different metallic materials. However, it is important to choose appropriate conditions to avoid residual stresses and consequently warping parts. (author)

  13. Strain measurement of objects subjected to aerodynamic heating using digital image correlation: experimental design and preliminary results.

    Pan, Bing; Jiang, Tianyun; Wu, Dafang

    2014-11-01

    In thermomechanical testing of hypersonic materials and structures, direct observation and quantitative strain measurement of the front surface of a test specimen directly exposed to severe aerodynamic heating has been considered as a very challenging task. In this work, a novel quartz infrared heating device with an observation window is designed to reproduce the transient thermal environment experienced by hypersonic vehicles. The specially designed experimental system allows the capture of test article's surface images at various temperatures using an optical system outfitted with a bandpass filter. The captured images are post-processed by digital image correlation to extract full-field thermal deformation. To verify the viability and accuracy of the established system, thermal strains of a chromiumnickel austenite stainless steel sample heated from room temperature up to 600 °C were determined. The preliminary results indicate that the air disturbance between the camera and the specimen due to heat haze induces apparent distortions in the recorded images and large errors in the measured strains, but the average values of the measured strains are accurate enough. Limitations and further improvements of the proposed technique are discussed.

  14. Evaluating a digital ship design tool prototype: Designers' perceptions of novel ergonomics software.

    Mallam, Steven C; Lundh, Monica; MacKinnon, Scott N

    2017-03-01

    Computer-aided solutions are essential for naval architects to manage and optimize technical complexities when developing a ship's design. Although there are an array of software solutions aimed to optimize the human element in design, practical ergonomics methodologies and technological solutions have struggled to gain widespread application in ship design processes. This paper explores how a new ergonomics technology is perceived by naval architecture students using a mixed-methods framework. Thirteen Naval Architecture and Ocean Engineering Masters students participated in the study. Overall, results found participants perceived the software and its embedded ergonomics tools to benefit their design work, increasing their empathy and ability to understand the work environment and work demands end-users face. However, participant's questioned if ergonomics could be practically and efficiently implemented under real-world project constraints. This revealed underlying social biases and a fundamental lack of understanding in engineering postgraduate students regarding applied ergonomics in naval architecture. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. Digital dashboard design using multiple data streams for disease surveillance with influenza surveillance as an example.

    Cheng, Calvin K Y; Ip, Dennis K M; Cowling, Benjamin J; Ho, Lai Ming; Leung, Gabriel M; Lau, Eric H Y

    2011-10-14

    Great strides have been made exploring and exploiting new and different sources of disease surveillance data and developing robust statistical methods for analyzing the collected data. However, there has been less research in the area of dissemination. Proper dissemination of surveillance data can facilitate the end user's taking of appropriate actions, thus maximizing the utility of effort taken from upstream of the surveillance-to-action loop. The aims of the study were to develop a generic framework for a digital dashboard incorporating features of efficient dashboard design and to demonstrate this framework by specific application to influenza surveillance in Hong Kong. Based on the merits of the national websites and principles of efficient dashboard design, we designed an automated influenza surveillance digital dashboard as a demonstration of efficient dissemination of surveillance data. We developed the system to synthesize and display multiple sources of influenza surveillance data streams in the dashboard. Different algorithms can be implemented in the dashboard for incorporating all surveillance data streams to describe the overall influenza activity. We designed and implemented an influenza surveillance dashboard that utilized self-explanatory figures to display multiple surveillance data streams in panels. Indicators for individual data streams as well as for overall influenza activity were summarized in the main page, which can be read at a glance. Data retrieval function was also incorporated to allow data sharing in standard format. The influenza surveillance dashboard serves as a template to illustrate the efficient synthesization and dissemination of multiple-source surveillance data, which may also be applied to other diseases. Surveillance data from multiple sources can be disseminated efficiently using a dashboard design that facilitates the translation of surveillance information to public health actions.

  16. Design iteration in construction projects – Review and directions

    Purva Mujumdar

    2018-03-01

    Full Text Available Design phase of any construction project involves several designers who exchange information with each other most often in an unstructured manner throughout the design phase. When these information exchanges happen to occur in cycles/loops, it is termed as design iteration. Iteration is an inherent and unavoidable aspect of any design phase which requires proper planning. Till date, very few researchers have explored the design iteration (“complexity” in construction sector. Hence, the objective of this paper was to document and review the complexities of iteration during design phase of construction projects for efficient design planning. To achieve this objective, exhaustive literature review on design iteration was done for four sectors – construction, manufacturing, aerospace, and software development. In addition, semi-structured interviews and discussions were done with a few design experts to verify the different dimensions of iteration. Finally, a design iteration framework was presented in this study that facilitates successful planning. Keywords: Design iteration, Types of iteration, Causes and impact of iteration, Models of iteration, Execution strategies of iteration

  17. Research on digital multi-channel pulse height analysis techniques

    Xiao Wuyun; Wei Yixiang; Ai Xianyun; Ao Qi

    2005-01-01

    Multi-channel pulse height analysis techniques are developing in the direction of digitalization. Based on digital signal processing techniques, digital multi-channel analyzers are characterized by powerful pulse processing ability, high throughput, improved stability and flexibility. This paper analyzes key techniques of digital nuclear pulse processing. With MATLAB software, main algorithms are simulated, such as trapezoidal shaping, digital baseline estimation, digital pole-zero/zero-pole compensation, poles and zeros identification. The preliminary general scheme of digital MCA is discussed, as well as some other important techniques about its engineering design. All these lay the foundation of developing homemade digital nuclear spectrometers. (authors)

  18. ''Econodump'' design for the Fermilab Direct Neutral Lepton Facility

    Childress, S.; Brown, C.; Koizumi, G.; Malensek, A.; Morfin, J.G.; Murphy, T.; Stefanski, R.; Wehman, A.; Lu, B.

    1986-08-01

    An extensive effort has been directed toward a major redesign of the Fermilab Direct Neutral Lepton Facility (DNLF). The goal has been a very significant cost reduction of the facility, with minimal sacrifice of physics potential. Hence the name ''Econodump'' applied to the redesign effort

  19. Design improvement of FPGA and CPU based digital circuit cards to solve timing issues

    Lee, Dongil; Lee, Jaeki; Lee, Kwang-Hyun

    2016-01-01

    The digital circuit cards installed at NPPs (Nuclear Power Plant) are mostly composed of a CPU (Central Processing Unit) and a PLD (Programmable Logic Device; these include a FPGA (Field Programmable Gate Array) and a CPLD (Complex Programmable Logic Device)). This type of structure is typical and is maintained using digital circuit cards. There are no big problems with this device as a structure. In particular, signal delay causes a lot of problems when various IC (Integrated Circuit) and several circuit cards are connected to the BUS of the backplane in the BUS design. This paper suggests a structure to improve the BUS signal timing problems in a circuit card consisting of CPU and FPGA. Nowadays, as the structure of circuit cards has become complex and mass data at high speed is communicated through the BUS, data integrity is the most important issue. The conventional design does not consider delay and the synchronicity of signal and this causes many problems in data processing. In order to solve these problems, it is important to isolate the BUS controller from the CPU and maintain constancy of the signal delay by using a PLD

  20. 162.5 MHz digital low-level radio frequency control monitoring system design and implementation

    Zhang Ruifeng; Wang Xianwu; Xu Zhe; Yi Xiaoping

    2014-01-01

    162.5 MHz high-frequency low-level control system self-developed by Institute of Modern Physics for ADS project took digital technology. All parameters' reading and writing, including loop parameter setting, open and close-loop operation, and condition monitoring, were achieved through the monitoring system. The system used lightweight client-server working mode that client running in the PC sent command data, server running on high-frequency digital low level system responded instructions to complete parameter monitoring and control. The system consisted of three parts. Firstly, server hardware system was constructed based on Atera Stratix Ⅲ family of field-programmable gate array (FPGA) development board. Secondly, the server software system was designed based on Micro C/OS Ⅱ real-time operating systems and lightweight TCP/IP protocol stack, and finally a client PC program was designed based on MFC. After a long test, it was indicated that the monitoring system works properly and stably. TCP sends and receives throughput reached 11.931038 Mbps and 8.117624 Mbps. (authors)

  1. Design improvement of FPGA and CPU based digital circuit cards to solve timing issues

    Lee, Dongil; Lee, Jaeki; Lee, Kwang-Hyun [KHNP CRI, Daejeon (Korea, Republic of)

    2016-10-15

    The digital circuit cards installed at NPPs (Nuclear Power Plant) are mostly composed of a CPU (Central Processing Unit) and a PLD (Programmable Logic Device; these include a FPGA (Field Programmable Gate Array) and a CPLD (Complex Programmable Logic Device)). This type of structure is typical and is maintained using digital circuit cards. There are no big problems with this device as a structure. In particular, signal delay causes a lot of problems when various IC (Integrated Circuit) and several circuit cards are connected to the BUS of the backplane in the BUS design. This paper suggests a structure to improve the BUS signal timing problems in a circuit card consisting of CPU and FPGA. Nowadays, as the structure of circuit cards has become complex and mass data at high speed is communicated through the BUS, data integrity is the most important issue. The conventional design does not consider delay and the synchronicity of signal and this causes many problems in data processing. In order to solve these problems, it is important to isolate the BUS controller from the CPU and maintain constancy of the signal delay by using a PLD.

  2. Clinical Digital Libraries Project: design approach and exploratory assessment of timely use in clinical environments*

    MacCall, Steven L.

    2006-01-01

    Objective: The paper describes and evaluates the use of Clinical Digital Libraries Project (CDLP) digital library collections in terms of their facilitation of timely clinical information seeking. Design: A convenience sample of CDLP Web server log activity over a twelve-month period (7/2002 to 6/2003) was analyzed for evidence of timely information seeking after users were referred to digital library clinical topic pages from Web search engines. Sample searches were limited to those originating from medical schools (26% North American and 19% non-North American) and from hospitals or clinics (51% North American and 4% non-North American). Measurement: Timeliness was determined based on a calculation of the difference between the timestamps of the first and last Web server log “hit” during each search in the sample. The calculated differences were mapped into one of three ranges: less than one minute, one to three minutes, and three to five minutes. Results: Of the 864 searches analyzed, 48% were less than 1 minute, 41% were 1 to 3 minutes, and 11% were 3 to 5 minutes. These results were further analyzed by environment (medical schools versus hospitals or clinics) and by geographic location (North America versus non-North American). Searches reflected a consistent pattern of less than 1 minute in these environments. Though the results were not consistent on a month-by-month basis over the entire time period, data for 8 of 12 months showed that searches shorter than 1 minute predominated and data for 1 month showed an equal number of less than 1 minute and 1 to 3 minute searches. Conclusions: The CDLP digital library collections provided timely access to high-quality Web clinical resources when used for information seeking in medical education and hospital or clinic environments from North American and non–North American locations and consistently provided access to the sought information within the documented two-minute standard. The limitations of the use of

  3. ASIC design of a digital fuzzy system on chip for medical diagnostic applications.

    Roy Chowdhury, Shubhajit; Roy, Aniruddha; Saha, Hiranmay

    2011-04-01

    The paper presents the ASIC design of a digital fuzzy logic circuit for medical diagnostic applications. The system on chip under consideration uses fuzzifier, memory and defuzzifier for fuzzifying the patient data, storing the membership function values and defuzzifying the membership function values to get the output decision. The proposed circuit uses triangular trapezoidal membership functions for fuzzification patients' data. For minimizing the transistor count, the proposed circuit uses 3T XOR gates and 8T adders for its design. The entire work has been carried out using TSMC 0.35 µm CMOS process. Post layout TSPICE simulation of the whole circuit indicates a delay of 31.27 ns and the average power dissipation of the system on chip is 123.49 mW which indicates a less delay and less power dissipation than the comparable embedded systems reported earlier.

  4. Design of Microcantilever-Based Biosensor with Digital Feedback Control Circuit

    Jayu P. Kalambe

    2012-01-01

    Full Text Available This paper present the design of cantilever-based biosensors with new readout, which hold promises as fast and cheap “point of care” device as well as interesting research tools. The fabrication process and related issues of the cantilever based bio-sensor are discussed. Coventorware simulation is carried out to analyze the device behavior. A fully integrated control circuit has been designed to solve manufacturing challenge which will take care of positioning of the cantilever instead of creating nanometer gap between the electrodes. The control circuit will solve the manufacturing challenge faced by the readout methods where it is essential to maintain precise gap between the electrodes. The circuit can take care of variation obtained due to fabrication process and maintain the precise gap between the electrodes by electrostatic actuation. The control circuit consist of analog and digital modules. The reliability issues of the sensor are also discussed.

  5. Digital tumor fluoroscopy (DTF)--a new direct imaging system in the therapy planning for brain tumors.

    Herbst, M; Fröder, M

    1990-01-01

    Digital Tumor Fluoroscopy is an expanded x-ray video chain optimized to iodine contrast with an extended Gy scale up to 64000 Gy values. Series of pictures are taken before and after injection of contrast medium. With the most recent unit, up to ten images can be taken and stored. The microprogrammable processor allows the subtraction of images recorded at any moment of the examination. Dynamic views of the distribution of contrast medium in the intravasal and extravasal spaces of brain and tumor tissue are gained by the subtraction of stored images. Tumors can be differentiated by studying the storage and drainage behavior of the contrast medium during the period of examination. Meningiomas store contrast medium very intensively during the whole time of investigation, whereas astrocytomas grade 2-3 pick it up less strongly at the beginning and release it within 2 min. Glioblastomas show a massive but delayed accumulation of contrast medium and a decreased flow-off-rate. In comparison with radiography and MR-imaging the most important advantage of Digital Tumor Fluoroscopy is that direct information on tumor localization is gained in relation to the skull-cap. This enables the radiotherapist to mark the treatment field directly on the skull. Therefore it is no longer necessary to calculate the tumor volume from several CT scans for localization. In radiotherapy Digital Tumor Fluoroscopy a unit combined with a simulator can replace CT planning. This would help overcome the disadvantages arising from the lack of a collimating system, and the inaccuracies which result from completely different geometric relationships between a CT unit and a therapy machine.

  6. Digital Sensor Technology

    Thomas, Ken D. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Quinn, Edward L. [Technology Resources, Dana Point, CA (United States); Mauck, Jerry L. [Technology Resources, Dana Point, CA (United States); Bockhorst, Richard M. [Technology Resources, Dana Point, CA (United States)

    2015-02-01

    The nuclear industry has been slow to incorporate digital sensor technology into nuclear plant designs due to concerns with digital qualification issues. However, the benefits of digital sensor technology for nuclear plant instrumentation are substantial in terms of accuracy and reliability. This paper, which refers to a final report issued in 2013, demonstrates these benefits in direct comparisons of digital and analog sensor applications. Improved accuracy results from the superior operating characteristics of digital sensors. These include improvements in sensor accuracy and drift and other related parameters which reduce total loop uncertainty and thereby increase safety and operating margins. An example instrument loop uncertainty calculation for a pressure sensor application is presented to illustrate these improvements. This is a side-by-side comparison of the instrument loop uncertainty for both an analog and a digital sensor in the same pressure measurement application. Similarly, improved sensor reliability is illustrated with a sample calculation for determining the probability of failure on demand, an industry standard reliability measure. This looks at equivalent analog and digital temperature sensors to draw the comparison. The results confirm substantial reliability improvement with the digital sensor, due in large part to ability to continuously monitor the health of a digital sensor such that problems can be immediately identified and corrected. This greatly reduces the likelihood of a latent failure condition of the sensor at the time of a design basis event. Notwithstanding the benefits of digital sensors, there are certain qualification issues that are inherent with digital technology and these are described in the report. One major qualification impediment for digital sensor implementation is software common cause failure (SCCF).

  7. Twelve-bit 20-GHz reduced size pipeline accumulator in 0.25 µm SiGe:C technology for direct digital synthesiser applications

    Jensen, Brian Sveistrup; Khafaji, M. Mahdi; Johansen, Tom Keinicke

    2012-01-01

    /Fmax of 180/220 GHz respectively. The accumulator architecture omits the pre-skewing registers of the pipeline, thereby lowering both power consumption and circuit complexity. Some limitations to this design are discussed and the necessary equations for determining the phase jump encountered each time......This article presents a 20 GHz, 12-bit pipeline accumulator with a reduced number of registers, suitable for direct digital synthesizer (DDS) applications. The accumulator is implemented in the IHP SG25H1 (0.25um) SiGe:C technology featuring heterojunction bipolar transistors (HBT) with Ft...... the control word (synthesized frequency) is changed are presented. For many applications employing signal processing after detection, this phase shift can then be corrected for. Compared to a full pipeline architecture, the implemented 12-bit accumulator reduces the number of registers by 55% and the power...

  8. Mechanical Design of an Omni-Directional Sensor Mount

    Rosheim, Mark

    2002-01-01

    This effort has been directed to development and demonstration of a gimbal mount capable of 180 degree singularity- free pitch and yaw motion about a two-axis center, avoiding the common problem of gimbal lock...

  9. Digital 2D-photogrammetry and direct anthropometry--a comparing study on test accomplishment and measurement data.

    Franke-Gromberg, Christine; Schüler, Grit; Hermanussen, Michael; Scheffler, Christiane

    2010-01-01

    The aim of this methodological anthropometric study was to compare direct anthropometry and digital two-dimensional photogrammetry in 18 male and 27 female subjects, aged 24 to 65 years, from Potsdam, Germany. In view of the rising interest in reliable biometric kephalofacial data, we focussed on head and face measurements. Out of 34 classic facial anatomical landmarks, 27 landmarks were investigated both by direct anthropometry and 2D-photogrammetry; 7 landmarks could not be localized by 2D-photogrammetry. Twenty-six kephalofacial distances were analysed both by direct anthropometry and digital 2D-photogrammetry. Kephalofacial distances are on average 7.6% shorter when obtained by direct anthropometry. The difference between the two techniques is particularly evident in total head height (vertex-gnathion) due to the fact that vertex is usually covered by hair and escapes from photogrammetry. Also the distances photographic sellion-gnathion (1.3 cm, i. e. 11.6%) and nasal-gnathion (1.2 cm, i. e. 9.4%) differ by more than one centimetre. Differences below 0.5 cm between the two techniques were found when measuring mucosa-lip-height (2.2%), gonia (3.0%), glabella-stomion (3.9%), and nose height (glabella-subnasal) (4.0%). Only the estimates of forehead width were significantly narrower when obtained by 2D-photogrammetry (-1.4 cm, -13.1%). The methodological differences increased with increasing magnitude of the kephalometric distance. Apart from these limitations, both techniques are similarly valid and may replace each other.

  10. Design and development experience with a digital fly-by-wire control system in an F-8C airplane

    Deets, D. A.

    1976-01-01

    To assess the feasibility of a digital fly by wire system, the mechanical flight control system of an F-8C airplane was replaced with a digital primary system and an analog backup system. The Apollo computer was used as the heart of the primary system. This paper discusses the experience gained during the design and development of the system and relates it to active control systems that are anticipated for future civil transport applications.

  11. Digital assessment in higher education: Promoting universal usability through requirements specification and universal design quality (UD-Q) reviews

    Begnum, Miriam E. Nes; Foss-Pedersen, Rikke Julie

    2017-01-01

    Statistics show there is a clear relationship between higher education and employment in Norway, especially for people with disabilities. The use of digital assessment solutions is increasing in Norwegian higher education. The overall goal of this study is therefore to highlight the potential for improvement of current practices related to universal design, both for providers of digital assessment solutions and for higher education institutions. Based on a case study of practices in Norwegian...

  12. Development of a novel direct X-ray detector using photoinduced discharge (PID) readout for digital radiography

    Heo, D.; Jeon, S.; Kim, J.-S.; Kim, R. K.; Cha, B. K.; Moon, B. J.; Yoon, J.

    2013-02-01

    We developed a novel direct X-ray detector using photoinduced discharge (PID) readout for digital radiography. The pixel resolution is 512 × 512 with 200 μm pixel and the overall active dimensions of the X-ray imaging panel is 10.24 cm × 10.24 cm. The detector consists of an X-ray absorption layer of amorphous selenium, a charge accumulation layer of metal, and a PID readout layer of amorphous silicon. In particular, the charge accumulation is pixelated because image charges generated by X-ray should be stored pixel by pixel. Here the image charges, or holes, are recombined with electrons generated by the PID method. We used a 405 nm laser diode and cylindrical lens to make a line beam source with a width of 50 μm for PID readout, which generates charges for each pixel lines during the scan. We obtained spatial frequencies of about 1.0 lp/mm for the X-direction (lateral direction) and 0.9 lp/mm for the Y-direction (scanning direction) at 50% modulation transfer function.

  13. DESIGN AND TESTING OF A DIGITAL REGULATOR FOR FERMILAB MAGNET POWER SYSTEMS

    Li Vigni, Vincenzo [Palermo U.

    2012-01-01

    In this thesis, the design of a digitally controlled DC power system for testing conventional and superconducting magnets is proposed. The designed PID controller performances have been tested by the 30kA test stand for superconducting magnets, Vertical Magnet Test Facility (VMTF), which is hosted at the Fermilab Magnet Test Facility (MTF). The system is implemented on a National Instruments CompactRIO and both real-time and FPGA targets are programmed. A full 24-bit PID algorithm is coded and successfully tested by a manual tuning approach. An automated tuning algorithm is then introduced. As it will be shown by simulation and experimental results, the proposed system meets all design specifications. The current loop stability is up to 14 times better than the existing regulator and a control accuracy less than 4 ppm is achieved. Shorted-bus tests of the PID regulator have been successfully performed on the VMTF power system. In order to test the generalization capability of the designed system towards different types of magnets, the system has been easily adapted to and tested on the 10kA conventional magnet test stand (Stand C at Fermilab). As shown by experimental results, the designed PID controller features really high performancesin terms of steady-state accuracy and effectiveness of the tuning algorithm.

  14. Current status and new directions in conceptual aircraft design

    Kidwell, George H., Jr.

    1990-01-01

    The following topics are discussed: systems analysis branch questions; systems analysis; historical perspective; background technology; conceptual design/evaluation program organization; system integration/vehicle closure; conceptual design synthesis programs; numerical optimization/mathematical programming; and current R&D interests. The discussion is presented in viewgraph format.

  15. Experimentally supported control design for a direct drive robot

    Kostic, D.; Jager, de A.G.; Steinbuch, M.

    2002-01-01

    We promote the idea of an experimentally supported control design as a successful way to achieve accurate tracking of reference robot motions, under disturbance conditions and given the uncertainties arising from modeling errors. The Hinf robust control theory is used for design of motion

  16. 76 FR 67631 - Airworthiness Directives; Cirrus Design Corporation Airplanes

    2011-11-02

    ... Corporation, 4515 Taylor Circle, Duluth, Minnesota 55811- 1548, phone: (218) 788-3000; fax: (218) 788-3525... as applicable. (f) Compliance Comply with this AD following Cirrus Design Corporation SR22T Service... this AD, contact Cirrus Design Corporation, 4515 Taylor Circle, Duluth, Minnesota 55811-1548, phone...

  17. Design and development of direct drive generators for wind turbines

    Nagrial, M.; Hellany, A.

    2011-01-01

    This paper discusses various options for wind generators in modern wind turbines without any gearbox. Various power converter configurations are also discussed. The design of modern and efficient variable speed generators is also proposed. The design of a novel permanent magnet generator is also given. (author)

  18. How digital design shapes political participation: A natural experiment with social information.

    Hale, Scott A; John, Peter; Margetts, Helen; Yasseri, Taha

    2018-01-01

    Political behaviour increasingly takes place on digital platforms, where people are presented with a range of social information-real-time feedback about the behaviour of peers and reference groups-which can stimulate (or depress) participation. This social information is hypothesized to impact the distribution of political activity, stimulating participation in mobilizations that are increasing in popularity, and depressing participation in those that appear to be less popular, leading to a non-normal distribution. Changes to these platforms can generate natural experiments allowing for an estimate of the impact of different kinds of social information on participation. This paper tests the hypothesis that social information shapes the distribution of political mobilizations by examining the introduction of trending information to the homepage of the UK government petition platform. The introduction of the trending feature did not increase the overall number of signatures per day, but the distribution of signatures across petitions changed significantly-the most popular petitions gained more signatures at the expense of those with fewer signatories. We further find significant differences between petitions trending at different ranks on the homepage. This evidence suggests that the ubiquity of trending information on digital platforms is introducing instability into political markets, as has been shown for cultural markets. As well as highlighting the importance of digital design in shaping political behaviour, the findings suggest that a non-negligible group of individuals visit the homepage of the site looking for petitions to sign, without having decided the issues they wish to support in advance. These 'aimless petitioners' are particularly susceptible to changes in social information.

  19. Decorative design of ceramic tiles adapted to inkjet printing employing digital image processing; Diseno decorativo de pavimentos ceramicos adaptado a inyeccion de tinta mediante tratamiento digital de imagen

    Defez, B.; Santiago-Praderas, V.; Lluna, E.; Peris-Fajarnes, G.; Dunai, E.

    2013-09-01

    The ceramic tile sector is a very competitive industry. The designer's proficiency to offer new models of the decorated surface, adapted to the production means, plays a very important role in the competitiveness. In the present work, we analyze the evolution of the design process in the ceramic sector, as much as the changes experimented in parallel by the printing equipment. Afterwards, we present a new concept of ceramic design, based on digital image processing. This technique allows the generation of homogeneous and non-repetitive designs for large surfaces, especially thought for inkjet printing. With the programmed algorithms we have compiled a prototype software for the assistance of the ceramic design. This tool allows creating continuous designs for large surfaces saving developing time. (Author)

  20. Is participatory design associated with the effectiveness of serious digital games for healthy lifestyle promotion? A meta-analysis

    Serious digital games can be effective at changing healthy lifestyles, but large differences in their effectiveness exist. The extent of user involvement in game design may contribute to game effectiveness by creating a better fit with user preferences. Participatory design (PD), which represents ac...