Modeling of high temperature- and diffusion-controlled die soldering in aluminum high pressure die casting

DEFF Research Database (Denmark)

Domkin, Konstantin; Hattel, Jesper Henri; Thorborg, Jesper

2009-01-01

of the die lifetime based on a quantitative analysis of die soldering in the framework of the numerical simulations of the die-casting process. Full 3D simulations of the process, including the filling. solidification, and the die cooling, are carried out using the casting simulation software MAGMAsoft....... The resulting transient temperature fields on the die surface and in the casting are then post-processed to estimate the die soldering. The present work deals only with the metallurgical/chemical kind of soldering which occurs at high temperatures and involves formation and growth of intermetallic layers...

Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Development of Surface Engineered Coating Systems for Aluminum Pressure Die Casting Dies: Towards a 'Smart' Die Coating

Energy Technology Data Exchange (ETDEWEB)

Dr. John J. Moore; Dr. Jianliang Lin,

2012-07-31

The main objective of this research program was to design and develop an optimal coating system that extends die life by minimizing premature die failure. In high-pressure aluminum die-casting, the die, core pins and inserts must withstand severe processing conditions. Many of the dies and tools in the industry are being coated to improve wear-resistance and decrease down-time for maintenance. However, thermal fatigue in metal itself can still be a major problem, especially since it often leads to catastrophic failure (i.e. die breakage) as opposed to a wear-based failure (parts begin to go out of tolerance). Tooling costs remain the largest portion of production costs for many of these parts, so the ability prevent catastrophic failures would be transformative for the manufacturing industry.The technology offers energy savings through reduced energy use in the die casting process from several factors, including increased life of the tools and dies, reuse of the dies and die components, reduction/elimination of lubricants, and reduced machine down time, and reduction of Al solder sticking on the die. The use of the optimized die coating system will also reduce environmental wastes and scrap parts. Current (2012) annual energy saving estimates, based on initial dissemination to the casting industry in 2010 and market penetration of 80% by 2020, is 3.1 trillion BTU's/year. The average annual estimate of CO2 reduction per year through 2020 is 0.63 Million Metric Tons of Carbon Equivalent (MM TCE).

Evaluation of porosity in Al alloy die castings

Directory of Open Access Journals (Sweden)

M. Říhová

2012-01-01

Full Text Available Mechanical properties of an Al-alloy die casting depend significantly on its structural properties. Porosity in Al-alloy castings is one of the most frequent causes of waste castings. Gas pores are responsible for impaired mechanical-technological properties of cast materials. On the basis of a complex evaluation of experiments conducted on AlSi9Cu3 alloy samples taken from the upper engine block which was die- cast with and without local squeeze casting it can be said that castings manufactured without squeeze casting exhibit maximum porosity in the longitudinal section. The area without local squeeze casting exhibits a certain reduction in mechanical properties and porosity increased to as much as 5%. However, this still meets the norms set by SKODA AUTO a.s.

Die casting copper motor rotors: mold materials and processing for cost-effective manufacturing

Energy Technology Data Exchange (ETDEWEB)

Peters, D.T.; Cowie, J.G.; Brush, E.F. Jr.

2000-07-01

This project seeks to demonstrate mold materials for copper pressure die-casting that are cost-effective and practical for production use in die-casting copper motor rotors. The incorporation of die-cast copper for conductor bars and end rings of the induction motor in place of aluminum would result in attractive improvements in motor energy efficiency through reductions in motor losses ranging from 15% to 20%. Die-cast motor rotors are produced in aluminum today because rotor fabrication by pressure die-casting is an established practice. Lack of a durable and cost-effective mold material has been the technical barrier preventing manufacture of the die-cast copper rotor. This project tested H-13 steel die inserts that establish the baseline. Nickel-, tungsten-, and molybdenum-based high temperature alloys were extensively tested. Results indicate that substantially extended die life is possible using high temperature die materials, pre-heated and operated at elevated temperatures. Pre-heating and high operating temperatures were shown to be critical in extending the die life by decreasing the cyclic stresses associated with thermal expansion. Extended die life provides the opportunity for economically viable copper motor rotor die-casting. (orig.)

Mathematical modeling of porosity formation in die cast A356 wheels

International Nuclear Information System (INIS)

Maijer, D.; Cockcroft, S.L.; Wells, M.A.; Luciuk, T.; Hermesmann, C.

2000-01-01

In an effort to leverage recent advances in modeling and process simulation tools, a mathematical model has been developed to predict porosity formation in die cast A356 wheels as part of a collaborative research agreement between researchers at the University of British Columbia and Canadian Autoparts Toyota Incorporated. The heat transfer model represents a three-dimensional, 30 o , slice of the wheel and die and is based on the commercial finite element code ABAQUS. Extensive temperature measurements in the die and in the wheel taken over several cycles in the casting process were used to fine tune and validate the model. Initial work on predicting porosity formation has focused on using the Niyama parameter as a measure of the probability of porosity. To date Niyama porosity predictions agree well with plant experience and show promise for reducing losses associated with porosity. (author)

Microstructures and properties of aluminum die casting alloys

Energy Technology Data Exchange (ETDEWEB)

M. M. Makhlouf; D. Apelian; L. Wang

1998-10-01

This document provides descriptions of the microstructure of different aluminum die casting alloys and to relate the various microstructures to the alloy chemistry. It relates the microstructures of the alloys to their main engineering properties such as ultimate tensile strength, yield strength, elongation, fatigue life, impact resistance, wear resistance, hardness, thermal conductivity and electrical conductivity. Finally, it serves as a reference source for aluminum die casting alloys.

Modeling and Analysis of The Pressure Die Casting Using Response Surface Methodology

International Nuclear Information System (INIS)

Kittur, Jayant K.; Herwadkar, T. V.; Parappagoudar, M. B.

2010-01-01

Pressure die casting is successfully used in the manufacture of Aluminum alloys components for automobile and many other industries. Die casting is a process involving many process parameters having complex relationship with the quality of the cast product. Though various process parameters have influence on the quality of die cast component, major influence is seen by the die casting machine parameters and their proper settings. In the present work, non-linear regression models have been developed for making predictions and analyzing the effect of die casting machine parameters on the performance characteristics of die casting process. Design of Experiments (DOE) with Response Surface Methodology (RSM) has been used to analyze the effect of effect of input parameters and their interaction on the response and further used to develop nonlinear input-output relationships. Die casting machine parameters, namely, fast shot velocity, slow shot to fast shot change over point, intensification pressure and holding time have been considered as the input variables. The quality characteristics of the cast product were determined by porosity, hardness and surface rough roughness (output/responses). Design of experiments has been used to plan the experiments and analyze the impact of variables on the quality of casting. On the other-hand Response Surface Methodology (Central Composite Design) is utilized to develop non-linear input-output relationships (regression models). The developed regression models have been tested for their statistical adequacy through ANOVA test. The practical usefulness of these models has been tested with some test cases. These models can be used to make the predictions about different quality characteristics, for the known set of die casting machine parameters, without conducting the experiments.

Modelling the Cast Component Weight in Hot Chamber Die Casting using Combined Taguchi and Buckingham's π Approach

Science.gov (United States)

Singh, Rupinder

2018-02-01

Hot chamber (HC) die casting process is one of the most widely used commercial processes for the casting of low temperature metals and alloys. This process gives near-net shape product with high dimensional accuracy. However in actual field environment the best settings of input parameters is often conflicting as the shape and size of the casting changes and one have to trade off among various output parameters like hardness, dimensional accuracy, casting defects, microstructure etc. So for online inspection of the cast components properties (without affecting the production line) the weight measurement has been established as one of the cost effective method (as the difference in weight of sound and unsound casting reflects the possible casting defects) in field environment. In the present work at first stage the effect of three input process parameters (namely: pressure at 2nd phase in HC die casting; metal pouring temperature and die opening time) has been studied for optimizing the cast component weight `W' as output parameter in form of macro model based upon Taguchi L9 OA. After this Buckingham's π approach has been applied on Taguchi based macro model for the development of micro model. This study highlights the Taguchi-Buckingham based combined approach as a case study (for conversion of macro model into micro model) by identification of optimum levels of input parameters (based on Taguchi approach) and development of mathematical model (based on Buckingham's π approach). Finally developed mathematical model can be used for predicting W in HC die casting process with more flexibility. The results of study highlights second degree polynomial equation for predicting cast component weight in HC die casting and suggest that pressure at 2nd stage is one of the most contributing factors for controlling the casting defect/weight of casting.

Development of materials for the rapid manufacture of die cast tooling

Science.gov (United States)

Hardro, Peter Jason

The focus of this research is to develop a material composition that can be processed by rapid prototyping (RP) in order to produce tooling for the die casting process. Where these rapidly produced tools will be superior to traditional tooling production methods by offering one or more of the following advantages: reduced tooling cost, shortened tooling creation time, reduced man-hours for tool creation, increased tool life, and shortened die casting cycle time. By utilizing RP's additive build process and vast material selection, there was a prospect that die cast tooling may be produced quicker and with superior material properties. To this end, the material properties that influence die life and cycle time were determined, and a list of materials that fulfill these "optimal" properties were highlighted. Physical testing was conducted in order to grade the processability of each of the material systems and to optimize the manufacturing process for the downselected material system. Sample specimens were produced and microscopy techniques were utilized to determine a number of physical properties of the material system. Additionally, a benchmark geometry was selected and die casting dies were produced from traditional tool materials (H13 steel) and techniques (machining) and from the newly developed materials and RP techniques (selective laser sintering (SLS) and laser engineered net shaping (LENS)). Once the tools were created, a die cast alloy was selected and a preset number of parts were shot into each tool. During tool creation, the manufacturing time and cost was closely monitored and an economic model was developed to compare traditional tooling to RP tooling. This model allows one to determine, in the early design stages, when it is advantageous to implement RP tooling and when traditional tooling would be best. The results of the physical testing and economic analysis has shown that RP tooling is able to achieve a number of the research objectives, namely

Casting defects and mechanical properties of high pressure die cast Mg-Zn-Al-RE alloys

Energy Technology Data Exchange (ETDEWEB)

Xiao, Wenlong; Easton, Mark A.; Zhu, Suming; Nie, Jianfeng [CAST Cooperative Research Centre, Department of Materials Engineering Monash University, Melbourne, VIC (Australia); Dargusch, Matthew S. [School of Mechanical and Mining Engineering, University of Queensland, Brisbane, QLD (Australia); Gibson, Mark A. [CSIRO Process Science and Engineering, Melbourne, VIC (Australia); Jia, Shusheng [Key Laboratory of Automobile Materials, Ministry of Education, Department of Materials Science and Engineering Jilin University, Changchun (China)

2012-02-15

The die casting defects and tensile properties of high pressure die cast (HPDC) Mg-Zn-Al-RE alloys with various combinations of Zn and Al were studied. The results show that die casting defects in Mg-Zn-Al-RE alloys are affected by the percentage of Zn and Al contents. The hot tearing susceptibility (HTS) of Mg-Zn-Al-RE alloys tends to increase with increasing Zn content up to 6 wt%, while a further increase of Al and/or Zn content reduces the HTS. In tensile tests, the yield strength (YS) is generally improved by increasing Zn or Al content, whereas the tensile strength (TS) and ductility appear to depend largely on the presence of casting defects. Compared with Mg-Zn-Al alloys, the mechanical properties of the Mg-Zn-Al-RE alloy are significantly improved. The Mg-4Zn-4Al-4RE alloy is found to have few casting defects and the optimal tensile properties. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Automatic inspection of surface defects in die castings after machining

Directory of Open Access Journals (Sweden)

S. J. Świłło

2011-07-01

Full Text Available A new camera based machine vision system for the automatic inspection of surface defects in aluminum die casting was developed by the authors. The problem of surface defects in aluminum die casting is widespread throughout the foundry industry and their detection is of paramount importance in maintaining product quality. The casting surfaces are the most highly loaded regions of materials and components. Mechanical and thermal loads as well as corrosion or irradiation attacks are directed primarily at the surface of the castings. Depending on part design and processing techniques, castings may develop surface discontinuities such as cracks or tears, inclusions due to chemical reactions or foreign material in the molten metal, and pores that greatly influence the material ability to withstand these loads. Surface defects may act as a stress concentrator initiating a fracture point. If a pressure is applied in this area, the casting can fracture. The human visual system is well adapted to perform in areas of variety and change; the visual inspection processes, on the other hand, require observing the same type of image repeatedly to detect anomalies. Slow, expensive, erratic inspection usually is the result. Computer based visual inspection provides a viable alternative to human inspectors. Developed by authors machine vision system uses an image processing algorithm based on modified Laplacian of Gaussian edge detection method to detect defects with different sizes and shapes. The defect inspection algorithm consists of three parameters. One is a parameter of defects sensitivity, the second parameter is a threshold level and the third parameter is to identify the detected defects size and shape. The machine vision system has been successfully tested for the different types of defects on the surface of castings.

Thermal Fatigue of Die-Casting Dies: An Overview

Directory of Open Access Journals (Sweden)

Abdulhadi Hassan A.

2016-01-01

Full Text Available Coupled studies by experimental and numerical simulations are necessary for an increased understanding of the material behaviour as related to the interaction between the thermal and mechanical conditions. This paper focus on the mechanisms of thermal fatigue in the failure of dies and cores used in the die casting of aluminum alloys. The thermal fatigue resistance is expressed by two crack parameters which are the average maximum crack and the average cracked area. Samples of various types of H13 steel were compared with a standard H13 steel by testing under identical thermal fatigue cycles. To determine the thermal constraint developed in the sample during the test, a finite difference technique was used to obtain the temperature distribution, based on temperature measurements at the boundaries. The resulting stresses and strains were computed, and the strain calculated at the edge or weakest point of the sample was used to correlate the number of cycles to crack initiation. As the strain at the edge increased, the number of cycles to failure decreased. The influence of various factors on thermal fatigue behavior was studied including austenitizing temperature, surface condition, stress relieving, casting, vacuum melting, and resulfurization. The thermal fatigue resistance improved as the austenitizing temperature increased from 1750 to 2050ºF.

Metallic Reinforcement of Direct Squeeze Die Casting Aluminum Alloys for Improved Strength and Fracture Resistance

Energy Technology Data Exchange (ETDEWEB)

D. Schwam: J.F. Wallace: Y. Zhu: J.W. Ki

2004-10-01

The utilization of aluminum die casting as enclosures where internal equipment is rotating inside of the casting and could fracture requires a strong housing to restrain the fractured parts. A typical example would be a supercharger. In case of a failure, unless adequately contained, fractured parts could injure people operating the equipment. A number of potential reinforcement materials were investigated. The initial work was conducted in sand molds to create experimental conditions that promote prolonged contact of the reinforcing material with molten aluminum. Bonding of Aluminum bronze, Cast iron, and Ni-resist inserts with various electroplated coatings and surface treatments were analyzed. Also toughening of A354 aluminum cast alloy by steel and stainless steel wire mesh with various conditions was analyzed. A practical approach to reinforcement of die cast aluminum components is to use a reinforcing steel preform. Such performs can be fabricated from steel wire mesh or perforated metal sheet by stamping or deep drawing. A hemispherical, dome shaped casting was selected in this investigation. A deep drawing die was used to fabricate the reinforcing performs. The tendency of aluminum cast enclosures to fracture could be significantly reduced by installing a wire mesh of austenitic stainless steel or a punched austenitic stainless steel sheet within the casting. The use of reinforcements made of austenitic stainless steel wire mesh or punched austenitic stainless steel sheet provided marked improvement in reducing the fragmentation of the casting. The best strengthening was obtained with austenitic stainless steel wire and with a punched stainless steel sheet without annealing this material. Somewhat lower results were obtained with the annealed punched stainless steel sheet. When the annealed 1020 steel wire mesh was used, the results were only slightly improved because of the lower mechanical properties of this unalloyed steel. The lowest results were

Microstructure and mechanical properties of AM50 alloy according to thickness and forming condition of the products by a high pressure die-casting process

Energy Technology Data Exchange (ETDEWEB)

Park, Joon Hong [Dong-A University, Busan (Korea, Republic of); Kang, Chung Gil [Pusan National University, Busan (Korea, Republic of)

2013-10-15

In recent years, Magnesium (Mg) and its alloys have become a center of special interest in the automotive industry. Due to their high specific mechanical properties, they offer a significant weight saving potential in modern vehicle constructions. Most Mg alloys show very good machinability and processability, and even the most complicated die casting parts can be easily produced. The die casting process is a fast production method capable of a high degree of automation for which certain Mg alloys are ideally suited. Although Mg alloys are fulfilling the demands for low specific weight materials with excellent machining and casting abilities, they are still not used in die casting process to the same extent as the competing material aluminum. One of the reasons is that effects of various forming variables for die casting process is not closely examined from the viewpoint of die design. In this study, step die and flowability tests for AM50 were performed by die casting process according to various combination of casting pressure and plunger velocity. Microstructure, Vickers hardness and tensile tests were examined and performed for each specimen to verify effects of forming conditions.

Study on interfacial heat transfer coefficient at metal/die interface during high pressure die casting process of AZ91D alloy

Directory of Open Access Journals (Sweden)

GUO Zhi-peng

2007-02-01

Full Text Available The high pressure die casting (HPDC process is one of the fastest growing and most efficient methods for the production of complex shape castings of magnesium and aluminum alloys in today’s manufacturing industry.In this study, a high pressure die casting experiment using AZ91D magnesium alloy was conducted, and the temperature profiles inside the die were Measured. By using a computer program based on solving the inverse heat problem, the metal/die interfacial heat transfer coefficient (IHTC was calculated and studied. The results show that the IHTC between the metal and die increases right after the liquid metal is brought into the cavity by the plunger,and decreases as the solidification process of the liquid metal proceeds until the liquid metal is completely solidified,when the IHTC tends to be stable. The interfacial heat transfer coefficient shows different characteristics under different casting wall thicknesses and varies with the change of solidification behavior.

The simulation of magnesium wheel low pressure die casting based on PAM-CASTTM

International Nuclear Information System (INIS)

Peng Yinghong; Wang Yingchun; Li Dayong; Zeng Xiaoqin

2004-01-01

Magnesium is the lightest metal commonly used in engineering, with various excellent characteristics such as high strength and electromagnetic interference shielding capability. Particularly, the usage of magnesium in automotive industry can meet better the need to reduce fuel consumption and CO2 emissions. Nowadays, most current magnesium components in automobiles are made by die casting. In this paper, commercial software for die casting, PAM-CAST TM , was utilized to simulate the low pressure die casting process of magnesium wheel. Through calculating temperature field and velocity field during filling and solidification stages, the evolution of temperature distribution and liquid fraction was analyzed. Then, the potential defects including the gas entrapments in the middle of the spokes, shrinkages between the rim and the spokes were forecasted. The analytical results revealed that the mold geometry and die casting parameters should be improved in order to get the sound magnesium wheel. The reasons leading to these defects were also analyzed and the solutions to eliminate them were put forward. Furthermore, through reducing the pouring velocity, the air gas entrapments and partial shrinkages were eliminated effectively

Energy Saving Melting and Revert Reduction Technology: Improved Die Casting Process to Preserve the Life of the Inserts

Energy Technology Data Exchange (ETDEWEB)

David Schwam, PI; Xuejun Zhu, Sr. Research Associate

2012-09-30

lubricants and technical support. Experiments conducted with these lubricants demonstrated good protection of the substrate steel. Graphite and boron nitride used as benchmarks are capable of completely eliminating soldering and washout. However, because of cost and environmental considerations these materials are not widely used in industry. The best water-based die lubricants evaluated in this program were capable of providing similar protection from soldering and washout. In addition to improved part quality and higher production rates, improving die casting processes to preserve the life of the inserts will result in energy savings and a reduction in environmental wastes. Improving die life by means of optimized cooling line placement, baffles and bubblers in the die will allow for reduced die temperatures during processing, saving energy associated with production. The utilization of optimized die lubricants will also reduce heat requirements in addition to reducing waste associated with soldering and washout. This new technology was predicted to result in an average energy savings of 1.1 trillion BTU's/year over a 10 year period. Current (2012) annual energy saving estimates, based on commercial introduction in 2010, a market penetration of 70% by 2020 is 1.26 trillion BTU's/year. Along with these energy savings, reduction of scrap and improvement in casting yield will result in a reduction of the environmental emissions associated with the melting and pouring of the metal which will be saved as a result of this technology. The average annual estimate of CO2 reduction per year through 2020 is 0.025 Million Metric Tons of Carbon Equivalent (MM TCE).

Kinetics of steel heavy ingot formation in dies of semicontinuous-casting machines

International Nuclear Information System (INIS)

Tsukerman, V.Ya.; Marchenko, I.K.

1986-01-01

Formation kinetics of round section ingot of up to 0.67 m in diameter was analyzed in dies of semicontinuous-casting machines on casting of the most usable assortment steels: medium-carbon low-alloyed and chromium-nickel stainless steels. It is established that solidification coefficient decreases in direct proportion to ingot diameter. Value of different-thickness ingot skin at die outlet is in direct proportion to a casted steel overheating temperature, ingot diameter and inversely proportional to the number and diameter of holes in a ladder nozzle and square root of ingot drawing rate

Mortality among workers in a die-casting and electroplating plant.

Science.gov (United States)

Silverstein, M; Mirer, F; Kotelchuck, D; Silverstein, B; Bennett, M

1981-01-01

A proportional mortality and case-referent analysis of 238 deaths among hourly employees in an automobile hardware manufacturing plant was conducted. The major operations of the plant were zinc die casting and electroplating. Chemical exposure included die-casting emissions and mists from chrome and nickel plating. The chief proportional mortality finding was a significant excess of lung cancer among both white men and women. A case-referent analysis indicated a possible association between lung cancer and work in certain departments. The findings support the hypothesis of a work-related carcinogenic risk. Follow-up recommendations have been made.

SPH based modelling of oxide and oxide film formation in gravity die castings

International Nuclear Information System (INIS)

Ellingsen, K; M'Hamdi, M; Coudert, T

2015-01-01

Gravity die casting is an important casting process which has the capability of making complicated, high-integrity components for e.g. the automotive industry. Oxides and oxide films formed during filling affect the cast product quality. The Smoothed particle hydrodynamics (SPH) method is particularly suited to follow complex flows. The SPH method has been used to study filling of a gravity die including the formation and transport of oxides and oxide films for two different filling velocities. A low inlet velocity leads to a higher amount of oxides and oxide films in the casting. The study demonstrates the usefulness of the SPH method for an increased understanding of the effect of different filling procedures on the cast quality. (paper)

[Cervical adaptation of complete cast crowns of various metal alloys, with and without die spacers].

Science.gov (United States)

Stephano, C B; Roselino, R F; Roselino, R B; Campos, G M

1989-01-01

A metallic replica from a dental preparation for crown was used to make 8 class-IV stone dies. The wax patterns for the casting of the crowns were obtained in two conditions: a) from the stone die with no spacer; and b) from the stone die with an acrylic spacer. Thus, 64 metallic crowns were casted, using 4 different alloys: DURACAST (Cu-Al), NICROCAST (Ni-Cr) and DURABOND (Ni-Cr), and gold. The casted crowns were fitted in the metallic replica and measured as to the cervical discrepance of fitting. The results showed that the use of die spacers decreases the clinical discrepancies of fitting of the casted crowns (in a statistically significant level), no matter the metallic alloy employed.

The ‘full sleeve’ application in the horizontal cold-chamber machine for pressure die casting of aluminium alloys

Directory of Open Access Journals (Sweden)

Z. Konopka

2008-04-01

Full Text Available The ‘full sleeve’ construction has been designed and accomplished in the horizontal cold-chamber pressure die casting machine. Main part of this solution is a counter plunger placed in a movable die half which allows for full filling of the shot sleeve and precisely fixes the metal quantity needed for casting. The purpose of this new construction solution is mainly the reduction of the casting porosity caused by air entrapment and the improvement of both castability and accuracy of the die cavity reproduction. For such a redesigned machine there have been performed examinations consisting in pressure casting of AlSi9Cu alloy (EN AC-46000 at varying plunger velocity in the second stage of injection and varying intensification pressure. The alloy castability (the die filling ability has been measured for each parameter setting. For the purpose of comparison, similar measurements have been performed also for the conventional system without a counter plunger. The castability examination has been done by means of a specially designed die with an impression of a trial casting of variable wall thickness. The experiments have been held according to the assumed factor design 22, what allowed for determining the mathematical models describing the influence of die filling parameters on the castability and the die cavity reproduction level. Both alternatives of the experiment confirmed the positive influence of plunger velocity and intensification pressure increase on the improvement of castability, the measure of the latter being the filled length of the impression. Applying of the new ‘full sleeve’ solution has improved castability for each experiment by about 20% as compared with conventional alternative. Castability in the ‘full sleeve’ system has been increased even for low values of plunger velocity and intensification pressure. For both alternative systems the influence of plunger velocity has been found, as an average, by four times

Casting dimensional control and fatigue life prediction for permanent mold casting dies. Technical progress report, September 29, 1993-- September 30, 1994

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-11-01

First year efforts as part of a three year program to address metal casting dimensional control and fatigue life prediction for permanent mold casting dies are described. Procedures have been developed and implemented to collect dimensional variability data from production steel castings. The influence of process variation and casting geometry variables on dimensional tolerances have been investigated. Preliminary results have shown that these factors have a significant influence on dimensional variability, although this variability is considerably less than the variability indicated in current tolerance standards. Gage repeatability and reproducibility testing must precede dimensional studies to insure that measurement system errors are acceptably small. Also initial efforts leading to the development and validation of a CAD/CAE model to predict the thermal fatigue life of permanent molds for aluminum castings are described. An appropriate thermomechanical property database for metal, mold and coating materials has been constructed. A finite element model has been developed to simulate the mold temperature distribution during repeated casting cycles. Initial validation trials have indicated the validity of the temperature distribution model developed.

Analysis of the Causes of Cracks in a Thick-Walled Bush Made of Die-Cast Aluminum Bronze

Directory of Open Access Journals (Sweden)

Pisarek B.P.

2016-12-01

Full Text Available For the die casting conditions of aluminium bronzes assumed based on the literature data, a thick-walled bush was cast, made of complex aluminium bronze (Cu-Al-Fe-Ni-Cr. After the cast was removed from the mould, cracks were observed inside it. In order to identify the stage in the technological production process at which, potentially, the formation of stresses damaging the continuity of the microstructure created in the cast was possible (hot cracking and/or cold cracking, a computer simulation was performed. The article presents the results of the computer simulation of the process of casting the material into the gravity die as well as solidifying and cooling of the cast in the shape of a thick-walled bush. The simulation was performed with the use of the MAGMA5 program and by application of the CuAl10Ni5,5Fe4,5 alloy from the MAGMA5 program database. The results were compared with the location of the defects identified in the actual cast. As a result of the simulation of the die-casting process of this bush, potential regions were identified where significant principal stresses accumulate, which can cause local hot and cold cracking. Until now, no research has been made of die-cast aluminium bronzes with a Cr addition. Correlating the results of the computer simulation validated by the analysis of the actual cast made it possible to clearly determine the critical regions in the cast exposed to cracking and point to the causes of its occurrence. Proposals of changes in the bush die casting process were elaborated, in order to avoid hot tearing and cold cracking. The article discusses the results of preliminary tests being a prologue to the optimization of the die-casting process parameters of complex aluminium bronze thick-walled bushs.

Technical-economic modelling of an aluminium high pressure die casting system for automotive parts fabrication

International Nuclear Information System (INIS)

Faura, F.

1997-01-01

In the present paper a technical-economic model for an aluminium high pressure die casting system has been developed. In order to obtain the necessary data for correlations utilized by the model, has been analyzed the production systems of companies that use these processes. This has allowed to determine the most important technological variables that affect to the economical aspect of the process. A computer application has been developed which allows to explore easily the influence of different system parameters. (Author) 12 refs

Comparative study on microstructures and mechanical properties of the heat-treated Al–5.0Cu–0.6Mn–xFe alloys prepared by gravity die casting and squeeze casting

International Nuclear Information System (INIS)

Lin, Bo; Zhang, WeiWen; Lou, ZhaoHui; Zhang, DaTong; Li, YuanYuan

2014-01-01

Highlights: • Only two kind Fe-rich intermetallics are found in the heat-treated Al–5.0Cu–0.6Mn–xFe alloys. • Squeeze cast Al–5.0Cu–0.6Mn alloys containing 1.5% Fe have desirable mechanical properties. • The difference between gravity die cast and squeeze cast Al–5.0Cu–0.6Mn–xFe alloys. - Abstract: The Al–5.0 wt% Cu–0.6 wt% Mn alloys with different Fe contents were prepared by gravity die casting and squeeze casting. The difference in microstructures and mechanical properties of the T5 heat-treated alloys was examined by tensile test, optical microscopy, deep etching technique, scanning electron microscope and electron probe micro-analyzer. The results show that both β-Fe and α (CuFe) are observed in T5 heat-treated gravity die cast alloy and only α (CuFe) appears in the squeeze cast alloy when the Fe content is 0.5 wt%. When the Fe content is more than 1.0 wt%, the main Fe-rich intermetallics is α (CuFe) in both squeeze cast and gravity die cast alloys. The mechanical properties of both the gravity die cast and squeeze cast alloys decrease gradually with the increase of Fe content due to the decreased volume fraction of precipitation particles, the increased volume fraction of Fe-rich intermetallics and the increased size of α (Al) dendrites. The squeeze cast alloys with different Fe contents have superior mechanical properties compared to the gravity die cast alloys, which is mainly attributed to the reduction of porosity and refinement of Fe-rich intermetallics and α (Al) dendrite. In particularly, the elongation of the squeeze cast alloys is less sensitive to the Fe content than that of the gravity die cast alloys. An elongation level of 13.7% is obtained in squeeze cast alloy even when the Fe content is as high as 1.5%, while that of the gravity die cast alloy is only 5.3%

Metallographic assessment of Al-12Si high-pressure die casting escalator steps.

Science.gov (United States)

Vander Voort, George Frederic; Suárez-Peña, Beatriz; Asensio-Lozano, Juan

2014-10-01

A microstructural characterization study was performed on high-pressure die cast specimens extracted from escalator steps manufactured from an Al-12 wt.% Si alloy designed for structural applications. Black and white, color light optical imaging and scanning electron microscopy techniques were used to conduct the microstructural analysis. Most regions in the samples studied contained globular-rosette primary α-Al grains surrounded by an Al-Si eutectic aggregate, while primary dendritic α-Al grains were present in the surface layer. This dendritic microstructure was observed in the regions where the melt did not impinge directly on the die surface during cavity filling. Consequently, microstructures in the surface layer were nonuniform. Utilizing physical metallurgy principles, these results were analyzed in terms of the applied pressure and filling velocity during high-pressure die casting. The effects of these parameters on solidification at different locations of the casting are discussed.

Corrosion behavior of die-cast Mg-4Al-2Sn-xCa alloy

Energy Technology Data Exchange (ETDEWEB)

Park, Kyung Chul; Kim, Byeong Ho; Kim, Kyung Ro [Defence Agency for Technology and Quality, Jinju (Korea, Republic of); Cho, Dae Hyun; Park, Ik Min [Pusan National University, Busan (Korea, Republic of)

2016-05-15

In the present work, the effect of Ca additions on microstructure and corrosion characteristics of high pressure die-cast Mg-4Al-2Sn alloy has been investigated. Mg-4Al-2Sn-xCa (x= 0, 0.3 and 0.7wt.%) alloy was prepared by using a high pressure die-casting method. Results indicated that the microstructure of Mg-4Al-2Sn alloy consisted of α-Mg, Mg{sub 17}Al{sub 12} and Mg{sub 2}Sn phase. With increase of Ca additions, CaMgSn phase was newly formed and grain size was sharply decreased. From the test results, the corrosion resistance of die-cast Mg-4Al-2Sn alloy was significantly improved by Ca addition. It is considered that stabilization of Mg(OH){sub 2} layer and refinements of microstructure with increase of Ca additions.

77 FR 6587 - PHB Die Casting a Subsidiary of PHB, Inc., Including On-Site Leased Workers From Career Concepts...

Science.gov (United States)

2012-02-08

... DEPARTMENT OF LABOR Employment and Training Administration [TA-W-64,292] PHB Die Casting a... 19, 2008, applicable to workers of PHB Die Casting, a subsidiary of PHB, Inc., including on-site... production of die castings. New information shows that a worker from Burns Industrial Group (BIG Inc) was...

Die Casting Mold Design for Aluminum Alloy Shell of Instrument

Directory of Open Access Journals (Sweden)

Li Yuanyuan

2015-01-01

Full Text Available This paper is about die casting mold design for aluminum alloy shell of instrument. Three-dimensional model of the casting and mold are designed by using Pro/Engineer and AutoCad which can analyze forming quality. Digital design and theoretical calculation can greatly shorten product development cycle and mold design cycle, improve the accuracy of product design and mold design, and reduce the cost of mold design.

Energy Saving Melting and Revert Reduction Technology: Melting Efficiency in Die Casting Operations

Energy Technology Data Exchange (ETDEWEB)

David Schwam

2012-12-15

This project addressed multiple aspects of the aluminum melting and handling in die casting operations, with the objective of increasing the energy efficiency while improving the quality of the molten metal. The efficiency of melting has always played an important role in the profitability of aluminum die casting operations. Consequently, die casters need to make careful choices in selecting and operating melting equipment and procedures. The capital cost of new melting equipment with higher efficiency can sometimes be recovered relatively fast when it replaces old melting equipment with lower efficiency. Upgrades designed to improve energy efficiency of existing equipment may be well justified. Energy efficiency is however not the only factor in optimizing melting operations. Melt losses and metal quality are also very important. Selection of melting equipment has to take into consideration the specific conditions at the die casting shop such as availability of floor space, average quantity of metal used as well as the ability to supply more metal during peaks in demand. In all these cases, it is essential to make informed decisions based on the best available data.

High pressure die casting of Fe-based metallic glass

Science.gov (United States)

Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

2016-01-01

Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications. PMID:27725780

High pressure die casting of Fe-based metallic glass.

Science.gov (United States)

Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

2016-10-11

Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications.

High pressure die casting of Fe-based metallic glass

Science.gov (United States)

Ramasamy, Parthiban; Szabo, Attila; Borzel, Stefan; Eckert, Jürgen; Stoica, Mihai; Bárdos, András

2016-10-01

Soft ferromagnetic Fe-based bulk metallic glass key-shaped specimens with a maximum and minimum width of 25.4 and 5 mm, respectively, were successfully produced using a high pressure die casting (HPDC) method, The influence of die material, alloy temperature and flow rate on the microstructure, thermal stability and soft ferromagnetic properties has been studied. The results suggest that a steel die in which the molten metal flows at low rate and high temperature can be used to produce completely glassy samples. This can be attributed to the laminar filling of the mold and to a lower heat transfer coefficient, which avoids the skin effect in the steel mold. In addition, magnetic measurements reveal that the amorphous structure of the material is maintained throughout the key-shaped samples. Although it is difficult to control the flow and cooling rate of the molten metal in the corners of the key due to different cross sections, this can be overcome by proper tool geometry. The present results confirm that HPDC is a suitable method for the casting of Fe-based bulk glassy alloys even with complex geometries for a broad range of applications.

Tribological Properties of AlSi11-SiCp Composite Castings Produced by Pressure Die Casting Method

Directory of Open Access Journals (Sweden)

Konopka Z.

2014-08-01

Full Text Available The measurement results concerning the abrasive wear of AlSi11-SiC particles composites are presented in paper. The method of preparing a composite slurry composed of AlSi11 alloy matrix and 10, 20% vol.% of SiC particles, as well as the method of its high-pressure die casting was described. Composite slurry was injected into metal mould of cold chamber pressure die cast machine and castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. Very good uniform arrangement of SiC particles in volume composite matrix was observed and these results were publicated early in this journal. The kinetics of abrasive wear and correlation with SiC particles arrangement in composite matrix were presented. Better wear resistance of composite was observed in comparison with aluminium alloy. Very strong linear correlation between abrasive wear and particle arrangement was observed. The conclusion gives the analysis and the interpretation of the obtained results.

Low cycle fatigue behavior of die cast Mg-Al-Mn-Ce magnesium alloy

Directory of Open Access Journals (Sweden)

Wu Wei

2013-11-01

Full Text Available Fatigue failure is a main failure mode for magnesium and other alloys. It is beneficial for fatigue design and fatigue life improvement to investigate the low cycle fatigue behavior of magnesium alloys. In order to investigate the low cycle fatigue behavior of die cast Mg-Al-Mn-Ce magnesium alloy, the strain controlled fatigue experiments were performed at room temperature and fatigue fracture surfaces of specimens were observed with scanning election microscopy for the alloys under die-cast and aged states. Cyclic stress response curves, strain amplitude versus reversals to failure curve, total strain amplitude versus fatigue life curves and cyclic stress-strain curves of Mg-Al-Mn-Ce alloys were analyzed. The results show that the Mg-Al-Mn-Ce alloys under die-cast (F and aged (T5 states exhibit cyclic strain hardening under the applied total strain amplitudes, and aging treatment could greatly increase the cyclic stress amplitudes of die cast Mg-Al-Mn-Ce alloys. The relationships between the plastic strain amplitude, the elastic strain amplitude and reversals to failure of Mg-Al-Mn-Ce magnesium alloy under different treatment states could be described by Coffin-Manson and Basquin equations, respectively. Observations on the fatigue fracture surface of specimens reveal that the fatigue cracks initiate on the surface of specimens and propagate transgranularly.

Modeling of microstructure evolution of magnesium alloy during the high pressure die casting process

International Nuclear Information System (INIS)

Wu Mengwu; Xiong Shoumei

2012-01-01

Two important microstructure characteristics of high pressure die cast magnesium alloy are the externally solidified crystals (ESCs) and the fully divorced eutectic which form at the filling stage of the shot sleeve and at the last stage of solidification in the die cavity, respectively. Both of them have a significant influence on the mechanical properties and performance of magnesium alloy die castings. In the present paper, a numerical model based on the cellular automaton (CA) method was developed to simulate the microstructure evolution of magnesium alloy during cold-chamber high pressure die casting (HPDC) process. Modeling of dendritic growth of magnesium alloy with six-fold symmetry was achieved by defining a special neighbourhood configuration and calculating of the growth kinetics from complete solution of the transport equations. Special attention was paid to establish a nucleation model considering both of the nucleation of externally solidified crystals in the shot sleeve and the massive nucleation in the die cavity. Meanwhile, simulation of the formation of fully divorced eutectic was also taken into account in the present CA model. Validation was performed and the capability of the present model was addressed by comparing the simulated results with those obtained by experiments.

Marginal adaptation of four inlay casting waxes on stone, titanium, and zirconia dies.

Science.gov (United States)

Michalakis, Konstantinos X; Kapsampeli, Vassiliki; Kitsou, Aikaterini; Kirmanidou, Yvone; Fotiou, Anna; Pissiotis, Argirios L; Calvani, Pasquale Lino; Hirayama, Hiroshi; Kudara, Yukio

2014-07-01

Different inlay casting waxes do not produce copings with satisfactory marginal accuracy when used on different die materials. The purpose of this study was to evaluate the marginal accuracy of 4 inlay casting waxes on stone dies and titanium and zirconia abutments and to correlate the findings with the degree of wetting between the die specimens and the inlay casting waxes. The inlay casting waxes tested were Starwax (Dentaurum), Unterziehwachs (Bredent), SU Esthetic wax (Schuler), and Sculpturing wax (Renfert). The marginal opening of the waxes was measured with a stereomicroscope on high-strength stone dies and on titanium and zirconia abutments. Photographic images were obtained, and the mean marginal opening for each specimen was calculated. A total of 1440 measurements were made. Wetting between die materials and waxes was determined after fabricating stone, titanium, and zirconia rectangular specimens. A calibrated pipette was used to place a drop of molten wax onto each specimen. The contact angle was calculated with software after an image of each specimen had been made with a digital camera. Collected data were subjected to a 2-way analysis of variance (α=.05). Any association between marginal accuracy and wetting of different materials was found by using the Pearson correlation. The wax factor had a statistically significant effect both on the marginal discrepancy (F=158.31, P<.001) and contact angle values (F=68.09, P<.001). A statistically significant effect of the die material factor both on the marginal adaptation (F=503.47, P<.001) and contact angle values (F=585.02, P<.001) was detected. A significant correlation between the marginal accuracy and the contact angle values (Pearson=0.881, P=.01) was also found. Stone dies provided wax copings with the best marginal integrity, followed by titanium and zirconia abutments. Unterziehwachs (Bredent), wax produced the best marginal adaptation on different die materials. A significant correlation was found

Water mist effect on cooling range and efficiency of casting die

Directory of Open Access Journals (Sweden)

R. Władysiak

2008-12-01

Full Text Available This project is showing investigation results of cooling process of casting die in the temperature range 570÷100 °C with 0.40 MPa compressed air and water mist streamed under pressure 0.25÷0.45 MPa in air jet 0.25÷0.50 MPa using open cooling system.The character and the speed of changes of temperature, forming of the temperture’s gradient along parallel layer to cooled surface of die is shawing with thermal and derivative curves. The effect of kind of cooling factor on the temperature and time and distance from cooling nozzle is presented in the paper. A designed device for generating the water mist cooling the die and the view of sprying water stream is shown here. It’s proved that using of the water mist together with the change of heat transfer interface increases intensity of cooling in the zone and makes less the range cooling zone and reduces the porosity of cast microstructure.

Numerical simulation and optimization of Al alloy cylinder body by low pressure die casting

Directory of Open Access Journals (Sweden)

Mi Guofa

2008-05-01

Full Text Available Shrinkage defects can be formed easily at Critical location during low pressure die casting (LPDC of aluminum alloy cylinder body. It has harmful effect on the products. Mold fi lling and solidifi cation process of a cylinder body was simulated by using of Z-CAST software. The casting method was improved based on the simulation results. In order to create effective feeding passage, the structure of casting was modifi ed by changing the location of strengthening ribs at the bottom, without causing any adverse effect on the part’s performance. Inserting copper billet at suitable location of the die is a valid way to create suitable solidifi cation sequence that is benefi cial to the feeding. Using these methods, the shrinkage defect was completely eliminated at the critical location.

A process chain for integrating piezoelectric transducers into aluminum die castings to generate smart lightweight structures

Directory of Open Access Journals (Sweden)

Stefan Stein

Full Text Available The application of piezoelectric transducers to structural body parts of machines or vehicles enables the combination of passive mechanical components with sensor and actuator functions in one single structure. According to Herold et al. [1] and Staeves [2] this approach indicates significant potential regarding smart lightweight construction. To obtain the highest yield, the piezoelectric transducers need to be integrated into the flux of forces (load path of load bearing structures. Application in a downstream process reduces yield and process efficiency during manufacturing and operation, due to the necessity of a subsequent process step of sensor/actuator application. The die casting process offers the possibility for integration of piezoelectric transducers into metal structures. Aluminum castings are particularly favorable due to their high quality and feasibility for high unit production at low cost (Brunhuber [3], Nogowizin [4]. Such molded aluminum parts with integrated piezoelectric transducers enable functions like active vibration damping, structural health monitoring or energy harvesting resulting in significant possibilities of weight reduction, which is an increasingly important driving force of automotive and aerospace industry (Klein [5], Siebenpfeiffer [6] due to increasingly stringent environmental protection laws. In the scope of those developments, this paper focuses on the entire process chain enabling the generation of lightweight metal structures with sensor and actuator function, starting from the manufacturing of piezoelectric modules over electrical and mechanical bonding to the integration of such modules into aluminum (Al matrices by die casting. To achieve this challenging goal, piezoceramic sensors/actuator modules, so-called LTCC/PZT modules (LPM were developed, since ceramic based piezoelectric modules are more likely to withstand the thermal stress of about 700 °C introduced by the casting process (Flössel et

Age hardening in die-cast Mg–Al–RE alloys due to minor Mn additions

Energy Technology Data Exchange (ETDEWEB)

Zhu, S.M., E-mail: suming.zhu@rmit.edu.au [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Abbott, T.B. [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Magontec Limited, Sydney, New South Wales 2000 (Australia); Gibson, M.A. [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); CSIRO Manufacturing Flagship, Clayton, Victoria 3168 (Australia); Nie, J.F. [Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Easton, M.A. [School Engineering, RMIT University, Carlton, Victoria 3053 (Australia)

2016-02-22

Die-cast Mg–Al–rare earth (RE) alloys are normally used in the as-cast condition without the application of heat treatment because it is a common perception that heat treatment will not provide benefit to these alloys. This paper reports, for the first time, that enhanced age hardenability can be achieved in die-cast Mg–Al–RE alloys with minor Mn additions. For example, the yield strength of Mg–4 wt%Al–3 wt%La alloy with 0.32 wt% Mn is increased by ∼34 MPa (∼26%) after ageing at 200 °C for 32 h (T5). The enhanced age hardenability is associated with the precipitation of nanoscale Al–Mn particles during ageing.

Simulation of Stress Distribution in a Thick- Walled Bushing Produced by Die-Casting

Directory of Open Access Journals (Sweden)

Pisarek B.P.

2017-12-01

Full Text Available Metallographic investigations and a computer simulation of stresses in a gravity die-casting bushing were performed. Simulation of the casting process, solidification of the thick-walled bushing and calculations of the stress was performed using MAGMA5.3 software. The size variability of phases κII affecting the formation of phase stresses σf, depending on the location of the metallographic test area, was identified. The distribution of thermal σt and shrinkage stresses σs, depending on the location of the control point SC in the bushing's volume, was estimated. Probably the nature of these stresses will change slightly even after machining. This can cause variations in operating characteristics (friction coefficient, wear. Due to the strong inhomogeneity of the stress distribution in the bushing's casting, it is necessary to perform further tests of the possibility to conduct thermal treatment guaranteeing homogenization of the internal stresses in the casting, as well as to introduce changes in the bushing' s construction and the casting technology. The paper presents the continuation of the results of research aimed at identifying the causes of defects in the thick-walled bushing, die-casting made of CuAl10Fe5Ni5Cr aluminium bronze.

Improved design and durability of aluminum die casting horizontal shot sleeves

Science.gov (United States)

Birceanu, Sebastian

The design and performance of shot sleeves is critical in meeting the engineering requirements of aluminum die cast parts. Improvement in shot sleeve materials have a major impact on dimensional stability, reproducibility and quality of the product. This investigation was undertaken in order to improve the life of aluminum die casting horizontal shot sleeves. Preliminary pin tests were run to evaluate the soldering, wash-out and thermal fatigue behavior of commercially available materials and coatings. An experimental rig was designed and constructed for shot sleeve configuration evaluation. Fabrication and testing of experimental shot sleeves was based upon preliminary results and manufacturing costs. Three shot sleeve designs and materials were compared to a reference nitrided H13 sleeve. Nitrided H13 is the preferred material for aluminum die casting shot sleeves because of wear resistance, strength and relative good soldering and wash-out resistance. The study was directed towards damage evaluation on the area under the pouring hole. This area is the most susceptible to damage because of high temperatures and impingement of molten aluminum. The results of this study showed that tungsten and molybdenum had the least amount of soldering and wash-out damage, and the best thermal fatigue resistance. Low solubility in molten aluminum and stability of intermetallic layers are main factors that determine the soldering and wash-out behavior. Thermal conductivity and thermal expansion coefficient directly influence thermal fatigue behavior. TiAlN nanolayered coating was chosen as the material with the best damage resistance among several commercial PVD coatings, because of relatively large thickness and simple deposition conditions. The results show that molybdenum thermal sprayed coating provided the best protection against damage under the pouring hole. Improved bonding is however required for life extension of the coating. TiAlN PVD coating applied on H13 nitrided

Determining the optimal index of heat stress in foundry, die casting and road construction industries using FAHP_Topsis

Directory of Open Access Journals (Sweden)

Maryam Dehghanipoor

2016-12-01

Full Text Available Introduction: Heat stress is one of the harmful risks in casting and die casting industries, which can not only cause work-related diseases but also can impair the performance and safety of workers. Since the indicators that are used to evaluate heat stress are very different, it is very difficult to choose a suitable index. The aim of this study was to determine the optimum heat stress index in foundry, die-cast, and road construction industries using FAHP and Topsis methods. Material and Method: In order to determine optimum heat stress index in foundry, die-cast, and road construction industries, first, the prioritization criteria were defined by experts (including ease of measurement, measurement accuracy, comprehensiveness, time, cost, and correlation. Then, considering these criteria, the best heat stress index was determined based on experts’ opinions and using FAHP and Topsis methods. Result: The results of this study suggest that given the current conditions and criteria, WBGT and P4SR is the best indices for foundry, die casting and construction. Conclusion: The results showed that according to comprehensiveness, accuracy and correlation criteria, the WBGT index is considered as the best indicator of heat stress assessment in foundry, die-cast and road construction industries. Moreover, the HSI ranked in the last place due to the complexity and cost of its calculation.

Numerical simulation of low pressure die-casting aluminum wheel

Directory of Open Access Journals (Sweden)

Mi Guofa

2009-02-01

Full Text Available The FDM numerical simulation software, ViewCast system, was employed to simulate the low pressure die casting (LPDC of an aluminum wheel. By analyzing the mold-fi lling and solidifi cation stage of the LPDC process, the distribution of liquid fraction, temperature field and solidification pattern of castings were studied. The potential shrinkage defects were predicted to be formed at the rim/spoke junctions, which is in consistence with the X-ray detection result. The distribution pattern of the defects has also been studied. A solution towards reducing such defects has been presented. The cooling capacity of the mold was improved by installing water pipes both in the side mold and the top mold. Analysis on the shrinkage defects under forced cooling mode proved that adding the cooling system in the mold is an effective method for reduction of shrinkage defects.

Microstructure investigation and first-principle analysis of die-cast AZ91 alloy with calcium addition

International Nuclear Information System (INIS)

Lin, L.; Wang, F.; Yang, L.; Chen, L.J.; Liu, Z.; Wang, Y.M.

2011-01-01

Highlights: → Die-cast AZ91 with Ca addition was investigated experimentally and theoretically. → Precipitation sequence was confirmed with increasing Ca addition. → Phase stability difference was verified by first-principle calculation. → Valence configurations were associated with alloying effects of Al, Mg and Ca. - Abstract: In order to get improved mechanical properties of die-cast AZ91 alloy under elevated temperatures, Ca element was added as a cost-effective alloying constituent. It appeared that minor Ca addition less than 0.5 wt% would result in no apparent change in microstructure, but the tensile strength at elevated temperatures was improved considerably. When increasing Ca addition to more than 1.0 wt%, Al 2 Ca phase will precipitate during solidification, no Mg 2 Ca phase was discovered. Homogeneous microstructure and high temperature stability in tensile strength of die-cast AZ91 alloy with Ca addition was mainly attributed to the precipitation of Al 2 Ca phase, which considerably refined the bulky β-Mg 17 Al 12 phase distributed originally at the grain boundaries of die-cast AZ91 alloy with no Ca addition. The priority of Al 2 Ca phase compared to Mg 2 Ca phase in precipitation sequence was verified by first-principle calculation of their cohesive energy and formation enthalpy, and can also be associated with more bounding electrons between Al and Ca atoms.

Energy and resource efficiency in aluminium die casting

CERN Document Server

Heinemann, Tim

2016-01-01

This monograph provides a field-proven approach to analyze industrial production with a cross-company scope as well as regarding all hierarchical system levels of manufacturing enterprises. The book exemplifies this approach in the context of aluminum  die casting, and presents a set of measures which allow a 30 percent energy reduction along the value chain. The target audience primarily comprises researchers and experts in the field but the book may also be beneficial for graduate students.

Development of Thin Section Zinc Die Casting Technology

Energy Technology Data Exchange (ETDEWEB)

Goodwin, Frank [International Lead Zinc Research Org., Inc., Durham, NC (United States)

2013-10-31

A new high fluidity zinc high pressure die casting alloy, termed the HF alloy, was developed during laboratory trials and proven in industrial production. The HF alloy permits castings to be achieved with section thicknesses of 0.3 mm or less. Technology transfer activities were conducted to develop usage of the HF high fluidity alloy. These included production of a brochure and a one-hour webinar on the HF alloy. The brochure was then sent to 1,184 product designers in the Interzinc database. There was excellent reception to this mailing, and from this initial contact 5 technology transfer seminars were conducted for 81 participants from 30 companies across a wide range of business sectors. Many of the successful applications to date involve high quality surface finishes. Design and manufacturing assistance was given for development of selected applications.

Tribological and Wear Performance of Nanocomposite PVD Hard Coatings Deposited on Aluminum Die Casting Tool

Directory of Open Access Journals (Sweden)

Jose Mario Paiva

2018-02-01

Full Text Available In the aluminum die casting process, erosion, corrosion, soldering, and die sticking have a significant influence on tool life and product quality. A number of coatings such as TiN, CrN, and (Cr,AlN deposited by physical vapor deposition (PVD have been employed to act as protective coatings due to their high hardness and chemical stability. In this study, the wear performance of two nanocomposite AlTiN and AlCrN coatings with different structures were evaluated. These coatings were deposited on aluminum die casting mold tool substrates (AISI H13 hot work steel by PVD using pulsed cathodic arc evaporation, equipped with three lateral arc-rotating cathodes (LARC and one central rotating cathode (CERC. The research was performed in two stages: in the first stage, the outlined coatings were characterized regarding their chemical composition, morphology, and structure using glow discharge optical emission spectroscopy (GDOES, scanning electron microscopy (SEM, and X-ray diffraction (XRD, respectively. Surface morphology and mechanical properties were evaluated by atomic force microscopy (AFM and nanoindentation. The coating adhesion was studied using Mersedes test and scratch testing. During the second stage, industrial tests were carried out for coated die casting molds. In parallel, tribological tests were also performed in order to determine if a correlation between laboratory and industrial tests can be drawn. All of the results were compared with a benchmark monolayer AlCrN coating. The data obtained show that the best performance was achieved for the AlCrN/Si3N4 nanocomposite coating that displays an optimum combination of hardness, adhesion, soldering behavior, oxidation resistance, and stress state. These characteristics are essential for improving the die mold service life. Therefore, this coating emerges as a novelty to be used to protect aluminum die casting molds.

Tribological and Wear Performance of Nanocomposite PVD Hard Coatings Deposited on Aluminum Die Casting Tool.

Science.gov (United States)

Paiva, Jose Mario; Fox-Rabinovich, German; Locks Junior, Edinei; Stolf, Pietro; Seid Ahmed, Yassmin; Matos Martins, Marcelo; Bork, Carlos; Veldhuis, Stephen

2018-02-28

In the aluminum die casting process, erosion, corrosion, soldering, and die sticking have a significant influence on tool life and product quality. A number of coatings such as TiN, CrN, and (Cr,Al)N deposited by physical vapor deposition (PVD) have been employed to act as protective coatings due to their high hardness and chemical stability. In this study, the wear performance of two nanocomposite AlTiN and AlCrN coatings with different structures were evaluated. These coatings were deposited on aluminum die casting mold tool substrates (AISI H13 hot work steel) by PVD using pulsed cathodic arc evaporation, equipped with three lateral arc-rotating cathodes (LARC) and one central rotating cathode (CERC). The research was performed in two stages: in the first stage, the outlined coatings were characterized regarding their chemical composition, morphology, and structure using glow discharge optical emission spectroscopy (GDOES), scanning electron microscopy (SEM), and X-ray diffraction (XRD), respectively. Surface morphology and mechanical properties were evaluated by atomic force microscopy (AFM) and nanoindentation. The coating adhesion was studied using Mersedes test and scratch testing. During the second stage, industrial tests were carried out for coated die casting molds. In parallel, tribological tests were also performed in order to determine if a correlation between laboratory and industrial tests can be drawn. All of the results were compared with a benchmark monolayer AlCrN coating. The data obtained show that the best performance was achieved for the AlCrN/Si₃N₄ nanocomposite coating that displays an optimum combination of hardness, adhesion, soldering behavior, oxidation resistance, and stress state. These characteristics are essential for improving the die mold service life. Therefore, this coating emerges as a novelty to be used to protect aluminum die casting molds.

Simulation of distortion and residual stress in high pressure die casting – modelling and experiments

International Nuclear Information System (INIS)

Hofer, P; Kaschnitz, E; Schumacher, P

2012-01-01

Two individual high-pressure die-casting geometries were developed in order to study the influence of process parameters and different alloys on the distortion behaviour of castings. These geometries were a stress lattice and a V-shaped sample tending to form residual stress due to different wall thickness respectively by a deliberate massive gating system. In the experimental castings the influence of the most important process parameters such as die temperature and die opening time and the cooling regime was examined. The time evolution of process temperatures was measured using thermal imaging. The heat transfer coefficients were adapted to the observed temperature distributions. Castings were produced from the two alloys AlSi12 and AlSi10MnMg. The distortion of the castings was measured by means of a tactile measuring device. For the alloy AlSi10MnMg thermo-physical and thermo-mechanical data were obtained using differential scanning calorimetry, laser flash technique, dilatometry and tensile testing at elevated temperatures. These data were used for modelling the material behaviour of the AlSi10MnMg alloy in the numerical model while for the alloy AlSi12(Fe) literature data were used. Process and stress simulation were conducted using the commercial FEM software ANSYS Workbench. A survey on the results of the comparison between simulation and experiment is given for both alloys.

Interlocking multi-material components made of structured steel sheets and high-pressure die cast aluminium

Science.gov (United States)

Senge, S.; Brachmann, J.; Hirt, G.; Bührig-Polaczek, A.

2017-10-01

Lightweight design is a major driving force of innovation, especially in the automotive industry. Using hybrid components made of two or more different materials is one approach to reduce the vehicles weight and decrease fuel consumption. As a possible way to increase the stiffness of multi-material components, this paper presents a process chain to produce such components made of steel sheets and high-pressure die cast aluminium. Prior to the casting sequence the steel sheets are structured in a modified rolling process which enables continuous interlocking with the aluminium. Two structures manufactured by this rolling process are tested. The first one is a channel like structure and the second one is a channel like structure with undercuts. These undercuts enable the formation of small anchors when the molten aluminium fills them. The correlation between thickness reduction during rolling and the shape of the resulting structure was evaluated for both structures. It can be stated that channels with a depth of up to 0.5 mm and a width of 1 mm could be created. Undercuts with different size depending on the thickness reduction could be realised. Subsequent aluminium high-pressure die casting experiments were performed to determine if the surface structure can be filled gap-free with molten aluminium during the casting sequence and if a gap-free connection can be achieved after contraction of the aluminium. The casting experiments showed that both structures could be filled during the high-pressure die casting. The channel like structure results in a gap between steel and aluminium after contraction of the cast metal whereas the structure with undercuts leads to a good interlocking resulting in a gap-free connection.

Microstructure and Properties of Cobalt-and Zinc-Containing Magnetic Magnesium Alloys Processed by High-Pressure Die Casting

Science.gov (United States)

Klose, Christian; Demminger, Christian; Maier, Hans Jürgen

The inherent magnetic properties of lightweight alloys based on magnesium and cobalt offer a novel way in order to measure mechanical loads throughout the entire structural component using the magnetoelastic effect. Because the solubility of cobalt in the magnesium matrix is negligible, the magnetic properties mainly originate from Co-rich precipitates. Thus, the size and distribution of Co-containing phases within the alloy's microstructure wields a major influence on the amplitude of the load-sensitive properties which can be measured by employing the harmonic analysis of eddy-current signals. In this study, Mg-Co-based alloys are produced by several casting methods which allow the application of different cooling rates, e.g. gravity die casting and high-pressure die casting. The differences between the manufactured alloys' micro- and phase structures are compared depending on the applied cooling rate and the superior magnetic and mechanical properties of the high-pressure die cast material are demonstrated.

Vacuum die casting of silicon sheet for photovoltaic applications. First quarterly report, March 16-June 30, 1979

Energy Technology Data Exchange (ETDEWEB)

None

1979-01-01

The obtective of this program is to develop a vacuum die-casting process for producing silicon sheet suitable for photovoltaic cells and to develop production techniques for optimization of polycrystallie silicon solar cell output. Efforts will examine process methods which are directed toward minimum cost processing of silicon into a quality suitable for producing solar cells with a terrestrial efficiency greater than 12% and having the potential to be scaled for large quantity production. In the vacuum die casting technique, silicon is melted under vacuum, and an evacuated die with a thin rectangular cavity is inserted into the melt. Liquid silicon is then injected into the die using a positive pressure of an inert gas. The major portion of the die casting work will be performed at Stanford Research Institute International under subcontract. The initial approach will follow parallel tracks: (1) obtain mechanical design parameters by using boron nitride, which has been shown to be non-wetting to silicon; (2) optimize silicon nitride material composition and coatings by sessile drop experiments; (3) test effectiveness of fluoride salt interfacial media with a graphite mold; and (4) test effect of surface finish using both boron nitride and graphite. Having established the material and mechanical boundary conditions, a finalized version of the prototype assembly will be constructed and the casting varibles determined. Polycrystalline silicon solar cells, with and without impurities, will be fabricated, characterized, and optimized at ARCCO Solar. The major activities will focus on the use of Wacker SILCO, HEM and in-house materials until vacuum die cast wafers are available. A baseline process with vacuum metallized contacts will be established and a reference mass production process with screen-printed metallization and high-throughput diffusions will also be obtained.

Die-cast of a hypo-eutectic AL-SI alloy: influence of injection temperature on microstructure and mechanical properties

International Nuclear Information System (INIS)

Santos, Silvano Leal dos; Santos, Sydney Ferreira

2014-01-01

Die-casting is widely used for manufacturing light alloy components for automotive industry. Among others, hypo-eutectic Al-Si alloys are currently processed by die-casting. To obtain high quality die-cast components, a better understanding on the correlations between processing parameters, microstructures, and mechanical properties are of utmost importance. In this study, we investigate the effect of injection temperature of liquid metal on the microstructure and mechanical properties of Al-Si alloy EN AC 46000 (DIN designation). The injection temperatures were 579, 589, 643, and 709 deg C. As-cast components had their microstructures analyzed by X-ray diffraction, optical and scanning electron microscopy, and X-ray energy dispersive spectroscopy. The mechanical properties were examined by micro-hardness and tensile tests. It was observed that the ultimate tensile strength slightly increased with the increase of injection temperature. The same trend was observed for micro-hardness. The amount of porosity in the samples varies in a small amount for different injection temperatures. On the other hand, the microstructure of the alloys seems more refined for higher temperatures of injection. This refinement in microstructure might play a major role on the mechanical properties of the Al-Si die-cast alloy. (author)

Microstructural analysis of the creep resistance of die-cast Mg-4Al-2RE alloy

Energy Technology Data Exchange (ETDEWEB)

Zhu, S.M. [CAST CRC, Department of Materials Engineering, Monash University, Victoria 3800 (Australia)], E-mail: suming.zhu@eng.monash.edu.au; Gibson, M.A. [CAST CRC, CSIRO Materials Science and Engineering, Private Bag 33, Clayton South MDC, Clayton, Victoria 3169 (Australia); Nie, J.F.; Easton, M.A. [CAST CRC, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); Abbott, T.B. [Advanced Magnesium Technologies, Milton, Queensland 4064 (Australia)

2008-03-15

The microstructure and microstructural stability of die-cast AE42 (Mg-4Al-2RE) alloy were investigated by transmission electron microscopy. It is shown that the formation of Mg{sub 17}Al{sub 12} after ageing at 200 deg. C is not due to the decomposition of A1{sub 11}RE{sub 3} as reported in the literature, but, rather, is associated with the supersaturation of Al solute in the {alpha}-Mg matrix. The level of Al solute retained in the {alpha}-Mg matrix after die-casting is suggested to be an important factor in influencing creep resistance.

Application of laser additive manufacturing to produce dies for aluminium high pressure die casting

CSIR Research Space (South Africa)

Pereira, MFVT

2012-07-01

Full Text Available through immersion in liquid aluminium. The dipping cycle closely resembles the heating and cooling cycle of a typical aluminium die under casting conditions. The suitability of any LAM technology, that can produce fully dense metallic components... cost vs wrought manufactured 5.2 1,7 2. 2 Average cost Very High Medium High Table 3: Processing and finishing costs of test coupons 3.1 Cyclic Immersion in Molten Aluminium Figure 3 below shows the testing apparatus developed to simulate...

A process chain for integrating piezoelectric transducers into aluminum die castings to generate smart lightweight structures

Science.gov (United States)

Stein, Stefan; Wedler, Jonathan; Rhein, Sebastian; Schmidt, Michael; Körner, Carolin; Michaelis, Alexander; Gebhardt, Sylvia

The application of piezoelectric transducers to structural body parts of machines or vehicles enables the combination of passive mechanical components with sensor and actuator functions in one single structure. According to Herold et al. [1] and Staeves [2] this approach indicates significant potential regarding smart lightweight construction. To obtain the highest yield, the piezoelectric transducers need to be integrated into the flux of forces (load path) of load bearing structures. Application in a downstream process reduces yield and process efficiency during manufacturing and operation, due to the necessity of a subsequent process step of sensor/actuator application. The die casting process offers the possibility for integration of piezoelectric transducers into metal structures. Aluminum castings are particularly favorable due to their high quality and feasibility for high unit production at low cost (Brunhuber [3], Nogowizin [4]). Such molded aluminum parts with integrated piezoelectric transducers enable functions like active vibration damping, structural health monitoring or energy harvesting resulting in significant possibilities of weight reduction, which is an increasingly important driving force of automotive and aerospace industry (Klein [5], Siebenpfeiffer [6]) due to increasingly stringent environmental protection laws. In the scope of those developments, this paper focuses on the entire process chain enabling the generation of lightweight metal structures with sensor and actuator function, starting from the manufacturing of piezoelectric modules over electrical and mechanical bonding to the integration of such modules into aluminum (Al) matrices by die casting. To achieve this challenging goal, piezoceramic sensors/actuator modules, so-called LTCC/PZT modules (LPM) were developed, since ceramic based piezoelectric modules are more likely to withstand the thermal stress of about 700 °C introduced by the casting process (Flössel et al., [7]). The

Fatigue Life Prediction in Rapid Die Casting - Preliminary Work in View of Current Research

International Nuclear Information System (INIS)

Chuan Huat Ng; Grote, Karl-Heinrich; Baehr, Ruediger

2007-01-01

Numerical simulation technique as a prediction tool is slowly adopted in metal casting industry for predicting design modelling solidification analysis. The reasons for this activity is found in the need to further enhance the geometrical design and mechanical properties of the tool design and the correct prediction methodology to fulfil industrial needs. The present state of numerical simulation capabilities in rapid die casting technologies is reviewed and the failure mode mechanisms of thermal fatigue, aimed at developing a numerical simulation with a systematic design guidance for predicting the thermal cyclic loading analysis and improvement is presented along with several other methods. The economic benefits of a numerical simulation technique in die casting are limited to tool life time, mechanical properties and design guidance. The extensive computer capabilities of a numerical simulation with a systematic design guidance methodology are exploited to provide a solution for flexible design, mechanical properties and mould life time. Related research carried out worldwide by different organisations and academic institutions are discussed

Effect of parameters of high-pressure die casting on occurrence of casting nonconformities in sleeves of silumin alloy EN AB 47100

Directory of Open Access Journals (Sweden)

Pałyga Ł.

2017-03-01

Full Text Available The paper presents a research on the effect of extreme - for the technology of the considered silumin EN AB 47100 - parameters of high-pressure die casting on occurrence of casting nonconformities. Considered was influence of the way of assembling the mould cooled-down to 140-160°C, non-standard for the selected casting, and pouring temperature in the range of 705 to 720°C (higher than the recommended of non-refined alloy. The castings were prepared with use of a high-pressure casting machine made by Kirov with mould closing force of 2500 kN. Occurrence of nonconformities was evaluated on properly prepared specimens taken from the castings manufactured with various parameters of the injection piston and various multiplication pressures. The results were subjected to quantitative and qualitative analyses of casting nonconformities and distribution of major alloying elements. It was found that proper selection of working parameters of the casting machine, in spite of disadvantageous pouring conditions, makes it possible to reduce occurrence of some casting defects, like shrinkage cavities and porosity, to improve tightness of castings even when the alloy refining process is omitted.

Modernity of parts in casting machines and coefficients of total productive maintenance

Directory of Open Access Journals (Sweden)

S. Borkowski

2010-10-01

Full Text Available The goal of this study is to investigate the impact of equipment efficiency in casting machines on the quality of die castings made of Al-Si alloys in consideration of their modernity. Analysis focused on two cold-chamber die-casting machines. The assessment of modernity ofthe equipment was made based on ABC analysis of technology and Parker’s scale. Then, the coefficients of total productive maintenance(TPM were employed for assessment of the efficiency of both machines. Using correlation coefficients r allowed authors to demonstrate the relationships between individual TPM coefficients and the number of non-conforming products. The finding of the study is pointing to the differences between the factors which determine the quality of castings resulting from the level of modernity of machines.

Assessment of Computer Simulation Software and Process Data for High Pressure Die Casting of Magnesium

Energy Technology Data Exchange (ETDEWEB)

Sabau, Adrian S [ORNL; Hatfield, Edward C [ORNL; Dinwiddie, Ralph Barton [ORNL; Kuwana, Kazunori [University of Kentucky; Viti, Valerio [University of Kentucky, Lexington; Hassan, Mohamed I [University of Kentucky, Lexington; Saito, Kozo [University of Kentucky

2007-09-01

Computer software for the numerical simulation of solidification and mold filling is an effective design tool for cast structural automotive magnesium components. A review of commercial software capabilities and their validation procedures was conducted. Aside form the software assessment, the program addressed five main areas: lubricant degradation, lubricant application, gate atomization, and heat transfer at metal mold interfaces. A test stand for lubricant application was designed. A sensor was used for the direct measurement of heat fluxes during lubricant application and casting solidification in graphite molds. Spray experiments were conducted using pure deionized water and commercial die lubricants. The results show that the sensor can be used with confidence for measuring heat fluxes under conditions specific to the die lube application. The data on heat flux was presented in forms suitable for use in HPDC simulation software. Severe jet breakup and atomization phenomena are likely to occur due to high gate velocities in HPDC. As a result of gate atomization, droplet flow affects the mold filling pattern, air entrapment, skin formation, and ensuing defects. Warm water analogue dies were designed for obtaining experimental data on mold filling phenomena. Data on break-up jet length, break-up pattern, velocities, and droplet size distribution were obtained experimentally and was used to develop correlations for jet break-up phenomena specific to die casting gate configurations.

Procedure of a secure design calculation for transmission housings made of aluminium die cast; Ablauf einer sicheren Auslegungsberechnung von Getriebegehaeusen aus Aluminiumdruckguss

Energy Technology Data Exchange (ETDEWEB)

Varenkamp, Marco; Schoen, Michael [ZF Friedrichshafen AG, Friedrichshafen (Germany). Fachbereich Berechnung und Simulation

2011-07-01

The challenges in life time calculation of transmission housings made of aluminium die cast are on the one hand the complex geometry of the parts and on the other hand the defects in the material such as pores resulting from the die-cast process. The calculations are carried out using the finite element method and the local strain approach. The problem of transferability within the local strain approach is mastered by comparison with component tests and improvement of the transfer functions based on statistical evaluation. The secure design is assured by a safety factor derived from the confidence probability. With the help of an example the procedure will be explained. In addition it will be shown that under uniaxial variable amplitude loading the calculation result can be improved using the damage parameter PJ. (orig.)

An establish attempt of reasons of machining splinter formation in AC44200 alloy high pressure die castings

OpenAIRE

J. Mutwil

2008-01-01

A problem of splinter formation during machining the AC44200 alloy high pressure die casting has been experimental investigated. Inorder to establish the reason of this occurrence a set of 200 high pressure die casting of the tensile strength samples have been prepared. The tensile tests were carried out using a Zwick Z050 universal testing machine. JM-SPC program has been used for statistical analysis of test results. A large variability of tensile strength results has been found. In order t...

The Influence of Pressure Die Casting Parameters on the Castability of AlSi11-SiCp Composites

Directory of Open Access Journals (Sweden)

Konopka Z.

2015-03-01

Full Text Available The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the castability of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of castability of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.

Inventory of pollution reduction options for an aluminium pressure die casting plant

NARCIS (Netherlands)

Neto, B.A.F.; Kroeze, C.; Hordijk, L.; Costa, C.

2009-01-01

This study presents an overview of options aiming to reduce emissions to air, soil and water from an aluminium die casting plant located in Portugal. We identify eighteen pollution reduction options and then estimate their potential to reduce the pollution, and the costs associated with their

Dislocation analysis of die-cast Mg-Al-Ca alloy after creep deformation

International Nuclear Information System (INIS)

Terada, Yoshihiro; Itoh, Daigo; Sato, Tatsuo

2009-01-01

Tensile creep tests were combined with detailed transmission electron microscopy in order to characterize the dislocation movements during creep and to explain the creep properties of the Mg-Al-Ca AX52 die-cast alloy at 473 K and stresses from 15 to 70 MPa. TEM observations indicate that dislocations are generated within the primary α-Mg grain in the die-casting process, which consist of both the basal and non-basal segments. The basal segments of dislocations are able to bow out and glide on the basal planes under the influence of a stress, and the jogs follow the basal segments with the help of climb during creep. The creep mechanism for the alloy is deduced as dislocation climb due to the formation of sub-boundaries during creep, while the easy glide of the basal segments of dislocations is controlling the creep rates immediately after the stress application of creep tests.

Thermal Stress Analysis for Ceramics Stalk in the Low Pressure Die Casting Machine

Science.gov (United States)

Noda, Nao-Aki; Hendra, Nao-Aki; Takase, Yasushi; Li, Wenbin

Low pressure die casting (LPDC) is defined as a net shape casting technology in which the molten metal is injected at high speeds and pressure into a metallic die. The LPDC process is playing an increasingly important role in the foundry industry as a low-cost and high-efficiency precision forming technique. The LPDC process is that the permanent die and filling systems are placed over the furnace containing the molten alloy. The filling of the cavity is obtained by forcing the molten metal by means of a pressurized gas in order to rise into a ceramic tube, which connects the die to the furnace. The ceramics tube called stalk has high temperature resistance and high corrosion resistance. However, attention should be paid to the thermal stress when the stalk is dipped into the molten aluminum. It is important to develop the design of the stalk to reduce the risk of fracture because of low fracture toughness of ceramics. In this paper, therefore, the finite element method is applied to calculate the thermal stresses when the stalk is dipped into the crucible by varying the dipping speeds and dipping directions. It is found that the thermal stress can be reduced by dipping slowly if the stalk is dipped into the crucible vertically, while the thermal stress can be reduced by dipping fast if it is dipped horizontally.

Experiments on the Model Testing of the 2nd Phase of Die Casting Process Compared with the Results of Numerical Simulation

Directory of Open Access Journals (Sweden)

Dańko R.

2015-12-01

Full Text Available Experiments of filling the model moulds cavity of various inner shapes inserted in rectangular cavity of the casting die (dimensions: 280 mm (height × 190 mm (width × 10 mm (depth by applying model liquids of various density and viscosity are presented in the paper. Influence of die venting as well as inlet system area and inlet velocity on the volumetric rate of filling of the model liquid - achieved by means of filming the process in the system of a cold-chamber casting die was tested. Experiments compared with the results of simulation performed by means of the calculation module Novacast (Novaflow&Solid for the selected various casting conditions - are also presented in the paper.

The effect of equipment efficiency on occurrence of non-conforming products in die casting

Directory of Open Access Journals (Sweden)

S. Borkowski

2010-01-01

Full Text Available This study focuses on determination of the relationships between equipment efficiency in casting machines and the level of quality. The determination was made based on coefficients of Total Productive Maintenance and r correlation coefficient. The degree at which break-downs and downtime affect the occurrence of non-conforming products was also evaluated. The goal of further investigations is to deter-mine the structure of downtime and finding which downtime types have greatest impact on the quality of die-casting products.

Casting of microstructured shark skin surfaces and possible applications on aluminum casting parts

Directory of Open Access Journals (Sweden)

Todor Ivanov

2011-02-01

Full Text Available Within the project Functional Surfaces via Micro- and Nanoscaled Structures?which is part of the Cluster of Excellence 揑ntegrative Production Technology?established and financed by the German Research Foundation (DFG, an investment casting process to produce 3-dimensional functional surfaces down to a structural size of 1 μm on near-net-shape-casting parts has been developed. The common way to realize functional microstructures on metallic surfaces is to use laser ablation, electro discharge machining or micro milling. The handicap of these processes is their limited productivity. The approach of this project to raise the efficiency is to use the investment casting process to replicate microstructured surfaces by moulding from a laser-microstructured grand master pattern. The main research objective deals with the investigation of the single process steps of the investment casting process with regard to the moulding accuracy. Actual results concerning making of the wax pattern, suitability of ceramic mould and core materials for casting of an AlSi7Mg0.3 alloy as well as the knock-out behavior of the shells are presented. By using of the example of an intake manifold of a gasoline race car engine, a technical shark skin surface has been realized to reduce the drag of the intake air. The intake manifold consists of an air-restrictor with a defined inner diameter which is microstructured with technical shark skin riblets. For this reason the inner diameter cannot be drilled after casting and demands a very high accuracy of the casting part. A technology for the fabrication and demoulding of accurate microstructured castings are shown. Shrinkage factors of different moulding steps of the macroscopic casting part as well as the microscopic riblet structure have been examined as well.

Squeeze casting of aluminum alloy A380: Microstructure and tensile behavior

Directory of Open Access Journals (Sweden)

Li Fang

2015-09-01

Full Text Available A380 alloy with a relatively thick cross-section of 25 mm was squeeze cast using a hydraulic press with an applied pressure of 90 MPa. Microstructure and tensile properties of the squeeze cast A380 were characterized and evaluated in comparison with the die cast counterpart. Results show that the squeeze cast A380 possesses a porosity level much lower than the die cast alloy, which is disclosed by both optical microscopy and the density measurement technique. The results of tensile testing indicate the improved tensile properties, specifically ultimate tensile strength (UTS: 215.9 MPa and elongation (Ef: 5.4%, for the squeeze cast samples over those of the conventional high-pressure die cast part (UTS: 173.7 MPa, Ef: 1.0%. The analysis of tensile behavior shows that the squeeze cast A380 exhibits a high tensile toughness (8.5 MJ·m-3 and resilience (179.3 kJ·m-3 compared with the die cast alloy (toughness: 1.4 MJ·m-3, resilience: 140.6 kJ·m-3, despite that, during the onset of plastic deformation, the strain-hardening rate of the die cast specimen is higher than that of the squeeze cast specimens. The microstructure analyzed by the scanning electron microscopy (SEM shows that both the squeeze and die cast specimens contain the primary α-Al, Al2Cu, Al5FeSi phase and the eutectic Si phase. But, the Al2Cu phase present in the squeeze cast alloy is relatively large in size and quantity. The SEM fractography evidently reveals the ductile fracture features of the squeeze cast A380 alloy.

Casting Technology.

Science.gov (United States)

Wright, Michael D.; And Others

1992-01-01

Three articles discuss (1) casting technology as it relates to industry, with comparisons of shell casting, shell molding, and die casting; (2) evaporative pattern casting for metals; and (3) high technological casting with silicone rubber. (JOW)

Semi-solid high pressure die casting of metal matrix composites produced by liquid state processing

CSIR Research Space (South Africa)

Ivanchev, L

2012-10-01

Full Text Available stirring. The composite was then transferred to a High Pressure Die Casting (HPDC) machine in the semi-solid state. The micron size particles were found to be predominantly in the intergranular eutectic while the nano-particles were predominantly...

Energy Saving Melting and Revert Reduction Technology (E-SMARRT): Mechanical Performance of Dies

Energy Technology Data Exchange (ETDEWEB)

R. Allen Miller, Principal Investigator; Kabiri-Bamoradian, Contributors: Khalil; Delgado-Garza, Abelardo; Murugesan, Karthik; Ragab, Adham

2011-09-13

As a net shape process, die casting is intrinsically efficient and improvements in energy efficiency are strongly dependent on design and process improvements that reduce scrap rates so that more of the total consumed energy goes into acceptable, usable castings. A casting that is distorted and fails to meet specified dimensional requirements is typically remelted but this still results in a decrease in process yield, lost productivity, and increased energy consumption. This work focuses on developing, and expanding the use of, computer modeling methods that can be used to improve the dimensional accuracy of die castings and produce die designs and machine/die setups that reduce rejection rates due to dimensional issues. A major factor contributing to the dimensional inaccuracy of the casting is the elastic deformations of the die cavity caused by the thermo mechanical loads the dies are subjected to during normal operation. Although thermal and die cavity filling simulation are widely used in the industry, structural modeling of the die, particularly for managing part distortion, is not yet widely practiced. This may be due in part to the need to have a thorough understanding of the physical phenomenon involved in die distortion and the mathematical theory employed in the numerical models to efficiently model the die distortion phenomenon. Therefore, two of the goals of this work are to assist in efforts to expand the use of structural modeling and related technologies in the die casting industry by 1) providing a detailed modeling guideline and tutorial for those interested in developing the necessary skills and capability and 2) by developing simple meta-models that capture the results and experience gained from several years of die distortion research and can be used to predict key distortion phenomena of relevance to a die caster with a minimum of background and without the need for simulations. These objectives were met. A detailed modeling tutorial was

The Influence of Pressure Die Casting Parameters on the Mechanical Properties of AlSi11/10 Vol.% SiC Composite

Directory of Open Access Journals (Sweden)

Konopka Z.

2014-03-01

Full Text Available The paper presents the method of preparing a composite slurry composed of AlSi11 alloy matrix and 10 vol.% of SiC particles, as well as the method of its high-pressure die casting and the measurement results concerning the tensile strength, the yield point, the elongation and hardness of the obtained composite. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. There were found the regression equations describing the change of mechanical properties of the examined composite as a function of pressure die casting process parameters. The conclusion gives the analysis and the interpretation of the obtained results.

A 1-D Analytical Model for the Thermally Induced Stresses in the Mould Surface During Die Casting

DEFF Research Database (Denmark)

Hattel, Jesper; Hansen, Preben

1994-01-01

This paper presents an anlytically based method for predicting the normal stresses in a die mold surface exposed to a thermal load. A example of application of the method is the high-pressure di casting process where the surface stresses in critical cases lead to cracks. Expressions for the normal...... stresses as afunction of the thermal and mechanical properties have been developed for a casting both without and with a coating. Finally, the resulting relationships are derived and evaluated, with particular emphasis on the effect of the heat transfer coefficient between the casting and the mold....

Correlations Between Arrangement of Reinforcing Particles and Mechanical Properties in Pressure Die Cast AlSi11-SiC Composites

Directory of Open Access Journals (Sweden)

Konopka Z.

2014-06-01

Full Text Available The work presents the investigation results concerning the structure of composite pressure die castings with AlSi11 alloy matrix reinforced with SiC particles. Examination has been held for composites containing 10 and 20 volume percent of SiC particles. The arrangement of the reinforcing particles within the matrix has been qualitatively assessed in specimens cut out of the castings. The index of distribution was determined on the basis of particle count in elementary measuring fields. The tensile strength, the yield point and elongation of the obtained composite were measured. Composite castings were produced at various values of the piston velocity in the second stage of injection, diverse intensification pressure values, and various injection gate width values. The regression equation describing the change of the considered arrangement particles index and mechanical properties were found as a function of the pressure die casting parameters. The infuence of particle arrangement in composite matrix on mechanical properties these material was examined and the functions of correlations between values were obtained. The conclusion gives the analysis and the interpretation of the obtained results.

Relationship between casting modulus and grain size in cast A356 aluminium alloys

International Nuclear Information System (INIS)

Niklas, A; Abaunza, U; Fernández-Calvo, A I; Lacaze, J

2012-01-01

Microstructure of Al-Si alloy castings depends most generally on melt preparation and on the cooling rate imposed by the thermal modulus of the component. In the case of Al-Si alloys, emphasis is put during melt preparation on refinement of pro-eutectic (Al) grains and on modification of the Al-Si eutectic. Thermal analysis has been used since long to check melt preparation before casting, i.e. by analysis of the cooling curve during solidification of a sample cast in an instrumented cup. The conclusions drawn from such analysis are however valid for the particular cooling conditions of the cups. It thus appeared of interest to investigate how these conclusions could extrapolate to predict microstructure in complicated cast parts showing local changes in the solidification conditions. For that purpose, thermal analysis cups and instrumented sand and die castings with different thermal moduli and thus cooling rates have been made, and the whole set of cooling curves thus recorded has been analysed. A statistical analysis of the characteristic features of the cooling curves related to grain refinement in sand and die castings allowed determining the most significant parameters and expressing the cube of grain size as a polynomial of these parameters. After introduction of a further parameter quantifying melt refining an excellent correlation, with a R 2 factor of 0.99 was obtained.

Solidification and casting

CERN Document Server

Cantor, Brian

2002-01-01

INDUSTRIAL PERSPECTIVEDirect chillcasting of aluminium alloysContinuous casting of aluminium alloysContinuous casting of steelsCastings in the automotive industryCast aluminium-silicon piston alloysMODELLING AND SIMULATIONModelling direct chill castingMold filling simulation of die castingThe ten casting rulesGrain selection in single crystal superalloy castingsDefects in aluminium shape castingPattern formation during solidificationPeritectic solidificationSTRUCTURE AND DEFECTSHetergeneous nucleation in aluminium alloysCo

Strategies to reduce the environmental impact of an aluminium pressure die casting plant: A scenario analysis

NARCIS (Netherlands)

Neto, B.; Kroeze, C.; Hordijk, L.; Costa, C.; Pulles, M.P.J.

2009-01-01

This study explores a model (MIKADO) to analyse scenarios for the reduction of the environmental impact of an aluminium die casting plant. Our model calculates the potential to reduce emissions, and the costs associated with implementation of reduction options. In an earlier paper [Neto, B., Kroeze,

The Influence of Pressure Die Casting Parameters on Distribution of Reinforcing Particles in the AlSi11/10% SiC Composite

Directory of Open Access Journals (Sweden)

Pasieka A.

2013-09-01

Full Text Available The method of pressure die casting of composites with AlSi11 alloy matrix reinforced with 10 vol. % of SiC particles and the analysis of the distribution of particles within the matrix is presented. The composite castings were produced at various values of the piston velocity in the second stage of injection, at diverse intensification pressure values, and various injection gate width values. The distribution of particles over the entire cross-section of the tensile specimen is shown. The index of distribution was determined on the basis of particle count in elementary measuring fields. The regression equation describing the change of the considered index was found as a function of the pressure die casting parameters. The conclusion presents an analysis of the obtained results and their interpretation.

Annealing of chromium oxycarbide coatings deposited by plasma immersion ion processing (PIIP) for aluminum die casting

International Nuclear Information System (INIS)

Peters, A.M.; He, X.M.; Trkula, M.; Nastasi, M.

2001-01-01

Chromium oxycarbide coatings have been investigated for use as non-wetting coatings for aluminum die casting. This paper examines Cr-C-O coating stability and non-wetability at elevated temperatures for extended periods. Coatings were deposited onto 304 stainless steel from chromium carbonyl [Cr(CO) 6 ] by plasma immersion ion processing. The coatings were annealed in air at an aluminum die casting temperature of 700 deg. C up to 8 h. Coatings were analyzed using resonant ion backscattering spectroscopy, nanoindentation and pin-on-disk tribometry. Molten aluminum was used to determine coating wetting and contact angle. Results indicate that the surface oxide layer reaches a maximum thickness of 900 nm. Oxygen concentrations in the coatings increased from 24% to 34%, while the surface concentration rose to almost 45%. Hardness values ranged from 22.1 to 6.7 GPa, wear coefficients ranged from 21 to 8x10 -6 mm 3 /Nm and contact angles ranged from 156 deg. to 127 deg

Titanium Aluminide Casting Technology Development

Science.gov (United States)

Bünck, Matthias; Stoyanov, Todor; Schievenbusch, Jan; Michels, Heiner; Gußfeld, Alexander

2017-12-01

Titanium aluminide alloys have been successfully introduced into civil aircraft engine technology in recent years, and a significant order volume increase is expected in the near future. Due to its beneficial buy-to-fly ratio, investment casting bears the highest potential for cost reduction of all competing production technologies for TiAl-LPTB. However, highest mechanical properties can be achieved by TiAl forging. In view of this, Access e.V. has developed technologies for the production of TiAl investment cast parts and TiAl die cast billets for forging purposes. While these parts meet the highest requirements, establishing series production and further optimizing resource and economic efficiency are present challenges. In order to meet these goals, Access has recently been certified according to aircraft standards, aiming at qualifying parts for production on technology readiness level 6. The present work gives an overview of the phases of development and certification.

An establish attempt of reasons of machining splinter formation in AC44200 alloy high pressure die castings

Directory of Open Access Journals (Sweden)

J. Mutwil

2008-10-01

Full Text Available A problem of splinter formation during machining the AC44200 alloy high pressure die casting has been experimental investigated. Inorder to establish the reason of this occurrence a set of 200 high pressure die casting of the tensile strength samples have been prepared. The tensile tests were carried out using a Zwick Z050 universal testing machine. JM-SPC program has been used for statistical analysis of test results. A large variability of tensile strength results has been found. In order to find the reason of this variability the fracture surface investigations (macrographs for all of samples and SEM micrographs for chosen samples have been carried out. It has been establish that in all cases a significant decrease of tensile strength was caused by presence of inclusions or porosity. In lot of cases the inclusions have a form of oxide film.

Endurance in Al Alloy Melts and Wear Resistance of Titanium Matrix Composite Shot-Sleeve for Aluminum Alloy Die-casting

International Nuclear Information System (INIS)

Choi, Bong-Jae; Kim, Young-Jig; Sung, Si-Young

2012-01-01

The main purpose of this study was to evaluate the endurance against Al alloy melts and wear resistance of an in-situ synthesized titanium matrix composite (TMC) sleeve for aluminum alloy die-casting. The conventional die-casting shot sleeve material was STD61 tool steel. TMCs have great thermal stability, wear and oxidation resistance. The in-situ reaction between Ti and B4C leads to two kinds of thermodynamically stable reinforcements, such as TiBw and TiCp. To evaluate the feasibility of the application to a TMCs diecasting shot sleeve, the interfacial reaction behavior was examined between Al alloys melts with TMCs and STD61 tool steel. The pin-on-disk type dry sliding wear test was also investigated for TMCs and STD61 tool steel.

Numerical modeling of the thickness dependence of zinc die-cast materials

Science.gov (United States)

Page, Maria Angeles Martinez; Ruf, Matthias; Hartmann, Stefan

2017-11-01

Zinc die casting alloys show varying material properties over the thickness in their final solid state, which causes a change in the mechanical response for specimens with different thicknesses. In this article, we propose a modeling concept to account for the varying porosity in the constitutive modeling. The material properties are effectively incorporated by combining a partial differential equation describing the distribution of the pores by a structural parameter with the Mori-Tanaka approach for linear elasticity. The distribution of the porosity is determined by polished cut images, for which the procedure is explained in detail. Finite element simulations of the coupled system incorporating the thickness dependence show the applicability of this approach.

Improved Life of Die Casting Dies of H13 Steel by Attaining Improved Mechanical Properties and Distortion Control During Heat Treatment

Energy Technology Data Exchange (ETDEWEB)

J. F. Wallace; D. Schwam

1998-10-01

The ultimate goal of this project is to increase die casting die life by using fast enough quenching rates to obtain good toughness and fatigue resistance in premium grade H-13 steel dies. The main tasks of the project were to compile a database on physical and mechanical properties of H-13; conduct gas quenching experiments to determine cooling rates of dies in difference vacuum furnaces; measure the as-quenched distortion of dies and the residual stresses; generate finite element analysis models to predict cooling rates, distortion, and residual stress of gas quenched dies; and establish rules and create PC-based expert system for prediction of cooling rates, distortion, and residual stress in vacuum/gas quenched H-13 dies. Cooling curves during gas quenching of H-13 blocks and die shapes have been measured under a variety of gas pressure. Dimensional changes caused by the gas quenching processes have been determined by accurate mapping of all surfaces with coordinate measuring machines before and after the quench. Residual stresses were determined by the ASTM E837 hole-drilling strain gage method. To facilitate the computer modeling work, a comprehensive database of H-13 mechanical and physical properties has been compiled. Finite element analysis of the heat treated shapes has been conducted using the TRAST/ABAQUS codes. There is a good fit between the predicted and measured distortion contours. However, the magnitude of the predicted distortion and residual stresses does not match well the measured values. Further fine tuning of the model is required before it can be used to predict distortion and residual stress in a quantitative manner. This last step is a prerequisite to generating rules for a reliable expert system.

Cast Steels for Creep-Resistant Parts Used in Heat Treatment Plants

Directory of Open Access Journals (Sweden)

Drotlew A.

2012-12-01

Full Text Available Creep-resistant parts of heat treatment furnaces are in most cases made from high-alloyed chromium-nickel and nickel-chromium iron alloys, both cast and wrought. This paper presents the types of casting alloys used for this particular purpose, since the majority of furnace components are made by the casting process. Standards were cited which give symbols of alloy grades used in technical specifications by the domestic industry. It has been indicated that castings made currently are based on a wider spectrum of the creep-resistant alloy grades than the number of alloys covered by the standards. Alloy grades recommended by the technical literature for individual parts of the furnace equipment were given. The recommendations reflect both the type of the technological process used and the technical tasks performed by individual parts of the furnace equipment. Comments were also made on the role of individual alloying elements in shaping the performance properties of castings.

Cast Steels for Creep-resistant Parts Used in Heat Treatment Plants

Directory of Open Access Journals (Sweden)

A. Drotlew

2012-12-01

Full Text Available Creep-resistant parts of heat treatment furnaces are in most cases made from high-alloyed chromium-nickel and nickel-chromium ironalloys, both cast and wrought. This paper presents the types of casting alloys used for this particular purpose, since the majority of furnace components are made by the casting process. Standards were cited which give symbols of alloy grades used in technical specifications by the domestic industry. It has been indicated that castings made currently are based on a wider spectrum of the creep-resistant alloy grades than the number of alloys covered by the standards. Alloy grades recommended by the technical literature for individual parts of the furnace equipment were given. The recommendations reflect both the type of the technological process used and the technical tasks performed by individual parts of the furnace equipment. Comments were also made on the role of individual alloying elements in shaping the performance properties of castings.

Casting thermal simulation

International Nuclear Information System (INIS)

Shamsuddin bin Sulaiman

1994-01-01

The whole of this study is concerned with process simulation in casting processes. This study describes the application of the finite element method as an aid to simulating the thermal design of a high pressure die casting die by analysing the cooling transients in the casting cycle. Two types of investigation were carried out to model the linear and non-linear cooling behavior with consideration of a thermal interface effect. The simulated cooling for different stages were presented in temperature contour form. These illustrate the successful application of the Finite Element Method to model the process and they illustrate the significance of the thermal interface at low pressure

Research on Accuracy of Automatic System for Casting Measuring

Directory of Open Access Journals (Sweden)

Jaworski J.

2016-09-01

Full Text Available Ensuring the required quality of castings is an important part of the production process. The quality control should be carried out in a fast and accurate way. These requirements can be met by the use of an optical measuring system installed on the arm of an industrial robot. In the article a methodology for assessing the quality of robotic measurement system to control certain feature of the casting, based on the analysis of repeatability and reproducibility is presented. It was shown that industrial robots equipped with optical measuring systems have the accuracy allowing their use in the process of dimensional control of castings manufactured by lost-wax process, permanent-mould casting, and pressure die-casting.

Solidified structure of thin-walled titanium parts by vertical centrifugal casting

Directory of Open Access Journals (Sweden)

Wu Shiping

2011-05-01

Full Text Available The solidified structure of the thin-walled and complicated Ti-6Al-4V castings produced by the vertical centrifugal casting process was studied in the present work. The results show that the wall thickness of the section is featured with homogeneously distributed fine equiaxial grains, compared with the microstructure of the thick-walled section. The grain size of the castings has a tendency to decrease gradually with the increasing of the centrifugal radius. The inter-lamellar space in thick-walled casting parts is bigger than that of the thin-walled parts, and the profile of inter-lamellar space is not susceptible to the centrifugal radius.

Pressing Speed, Specific Pressure and Mechanical Properties of Aluminium Cast

Directory of Open Access Journals (Sweden)

Gaspar S.

2016-06-01

Full Text Available Recent research in the process of aluminum alloy die castings production, which is nowadays deeply implemented into the rapidly growing automobile, shipping and aircraft industries, is aimed at increasing the useful qualitative properties of the die casting in order to obtain its high mechanical properties at acceptable economic cost. Problem of technological factors of high pressure die casting has been a subject of worldwide research (EU, US, Japan, etc.. The final performance properties of die castings are subjected to a large number of technological factors. The main technological factors of high pressure die casting are as follows: plunger pressing speed, specific (increase pressure, mold temperature as well as alloy temperature. The contribution discusses the impact of the plunger pressing speed and specific (increase pressure on the mechanical properties of the casting aluminum alloy.

New high pressure die cast magnesium alloy AM-HP2 for powertrain applications

Energy Technology Data Exchange (ETDEWEB)

Gibson, M.A. [Queensland Univ., Brisbane (Australia). CAST CRC]|[CSIRO Manufacturing and Materials Technology, Clayton (Australia); Zhu, S.M.; Nie, J.F. [Queensland Univ., Brisbane (Australia). CAST CRC]|[Monash Univ., Monash (Australia). Dept. of Materials Engineering

2007-07-01

In order to improve the benefits available through weight savings on engine emissions, magnesium alloys must gain wider acceptance in transmission and engine applications. This paper provided details of a new alloy with exceptional creep properties developed for automotive powertrain applications. The AM-HP2 alloy was developed as part of a broader research program investigating the relationship between the composition, structure and properties of magnesium rare earth (Mg-RE) based alloys and high-pressure die casting (HPDC). Cylindrical test specimens of various alloys were produced on a cold chamber HPDC machine. Tensile creep tests were then conducted under a constant load at 177 degrees C for a period of 600 hours. Microstructures of specimens were characterized using a CM20 transmission electron microscope. Results of the tests indicated that near-grain boundary microstructure was an important parameter in securing optimum elevated temperature properties. The RE element had a significant effect on the creep behaviour of the HPDC Mg-RE alloys. It was concluded that further research is needed to investigate the influence of the RE mixture in improving creep performance. 15 refs., 2 tabs., 6 figs.

Influence of refining process on the porosity of high pressure die casting alloy Al-Si

Directory of Open Access Journals (Sweden)

A.W. Orlowicz

2009-04-01

Full Text Available This study presents research results of the influence that refining and transfer of AlSi12S alloy on the porosity of high pressure diecastings.Tests were conducted under production conditions of Die-casting Foundry META-ZEL Sp z o.o. The operation of refining was conducted in a melting furnace, with the use of an FDU Mini Degasser. Decay of the refining effect was assessed by evaluating the porosity content and metallographic examination.

Failure behavior of high pressure die casting AZ91D magnesium alloy

Energy Technology Data Exchange (ETDEWEB)

Li, X.; Xiong, S.M. [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084 (China); Guo, Z., E-mail: zhipeng_guo@mail.tsinghua.edu.cn [School of Materials Science and Engineering, Tsinghua University, Beijing 100084 (China); Key Laboratory for Advanced Materials Processing Technology, Ministry of Education, Tsinghua University, Beijing 100084 (China)

2016-08-30

The failure behavior of high pressure die casting AZ91D magnesium alloy during both tensile and fatigue tests was studied in situ by using scanning electron microscope. Attention was focused on the role of microstructure played in crack initiation and propagation. Results showed that the defects in castings, including gas pore, shrinkage pore and defect band, were the crack initiation sources. In tensile test, the crack propagated in a combination of intergranular and transgranular modes, and the specimen fractured by connecting defects at the section with minimum effective force bearing area. In fatigue test, the crack propagated in a transgranular mode at specific crystalline planes. When the crack was in contact with the β-phase, the crack would pass through, and fracture the network β-phase, whereas bypass the island β-phase by detaching it from the surrounding α-Mg grains. Besides, defects in front of the crack would act as the secondary crack initiation sources, from which new cracks would initiate and propagate. With the propagation of the fatigue crack, the actual maximum cyclic stress would increase to the fracture stress of the left cross section and lead to the final fracture of the specimen.

Comparative study on laser welding and TIG welding of semi-solid high pressure die cast A356 aluminium alloy

CSIR Research Space (South Africa)

Govender, G

2007-07-01

Full Text Available components. The low porosity levels in SSM high pressure die castings (HPDC) improves the weldability of these components. The aim of the current research was to perform a comparative study of laser and TIG welding of SSM HPDC aluminium alloy A356. SSM...

Numerical optimization of die geometry in open die forging

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

2013-01-01

This paper deals with numerical optimization of open die forging of large metallic ingots made by casting implying risk of defects, e.g. central pores. Different material hardening properties and die geometries are combined in order to investigate, which geometry gives rise to maximum closure...

An eco design strategy for high pressure die casting components: microstructural analysis applied to mass reducing processes

International Nuclear Information System (INIS)

Suarez-Pena, B.; Asensio-Lozano, J.

2009-01-01

In this work the study focused on the possibility of use of new aluminium alloys with optimized microstructures that ensure the mechanical properties requested for cast components made by high pressure die casting. The objective was to check the possibility of manufacture of structurally sound eco-steps for escalators with reduced structural integrity. The former arises as a result of a new redesign of the traditional steps aiming at a significant weight reduction. The experimental results show that it is feasible to cut the use of materials during processing and therefore to reduce the impact of the components during its lifetime, whilst the performance and safety standards are kept identical or even improved. (Author) 17 refs

The effect of natural pre-ageing on the mechanical properties of Rheo-High pressure die cast aluminium alloy 2139

CSIR Research Space (South Africa)

Chauke, L

2015-07-01

Full Text Available -high pressure die casting process (R-HPDC). Alloy 2139 is a Ag-containing aluminium alloy from the Al-Cu-Mg 2xxx series family. The addition of Ag enhances the age hardening response through the formation of co-clusters that act as precursors to the formation...

Marginal Accuracy of Castings Fabricated with Ringless Casting Investment System and Metal Ring Casting Investment System: A Comparative Study.

Science.gov (United States)

Kalavathi, M; Sachin, Bhuvana; Prasanna, B G; Shreeharsha, T V; Praveen, B; Ragher, Mallikarjuna

2016-02-01

The thermal expansion of the investment can be restricted by the metal casting ring because the thermal expansion of the ring is less than that of the investment. The ringless casting procedure is in use in clinical dentistry, though there is little scientific data to support its use in fixed partial dentures. In this study, marginal discrepancy of castings produced with the ringless casting technique and the conventional technique using the metal rings were compared. A total of 30 wax patterns were fabricated directly on a metal die. Optical stereomicroscope was used to measure the marginal discrepancy between the metal die and wax patterns. A total of 15 castings were invested using Bellavest T phosphate-bonded investment with the ringless technique and 15 were invested with the same investment with a metal ring; 30 castings were produced using a nickel-chromium ceramo-metal alloy. The internal surface of the castings was not modified and seated with finger pressure. The vertical marginal discrepancy was measured using an optical stereomicroscope at a magnification of 100x. The data obtained were statistically analyzed using students t-test (paired t-test and unpaired t-test). The castings of the ringless technique provided less vertical marginal discrepancy (240.56 ± 45.81 μ) than the castings produced with the conventional metal ring technique (281.98± 53.05 μ). The difference was statistically significant. The ringless casting technique had produced better marginal accuracy compared with conventional casting technique. Ringless casting system can be used routinely for clinical purpose.

First Results of Energy Saving at Process Redesign of Die Forging Al-Alloys

International Nuclear Information System (INIS)

Pepelnjak, Tomaz; Kuzman, Karl; Kokol, Anton

2011-01-01

The contribution deals with eco-friendly solutions for shortened production chains of forging light alloys. During the die forging operations a remarkable amount of material goes into the flash and later on into chips during finish machining. These low value side products are rich with embedded energy therefore recycling or reprocessing could be very energy saving procedure.In cooperation with a die forging company a shortened reprocessing cycle has been studied starting from re-melting the forging flash and without additional heating to cast preforms for subsequent die forging. As such preforms have not as good formability characteristics as those done from extruded billets the isothermal forging process has been adopted. First results showed that without cracks and other defects the formability is sufficient for a broad spectrum of forgings.To improve the formability a homogenization process of cast preforms has been implemented. As the process started immediately after casting, amount of additional energy for heating was minimized. To reduce voids forging process was redesigned in a way to assure greater hydrostatic pressures in parts during forging. First results were promising therefore research is going towards improving processes without adding significantly more energy as it is needed for casting with homogenization and die forging.

Evaluation of interlocking bond strength between structured 1.0338 steel sheets and high pressure die cast AlMg5Si2

Science.gov (United States)

Senge, S.; Brachmann, J.; Hirt, G.; Bührig-Polaczek, A.

2018-05-01

Multi-material components open up new possibilities for functional design. Such components combine beneficial physical properties of different materials in a single component as for instance chemical resistance, high strength or low density. The challenge is a reliable bond between both materials to enable a long term usage. This paper deals with a form closure connection to ensure a solid connection between steel strips and high pressure die cast aluminium. Two different sizes of channel structures with width ratios of 1.0 and 1.35 are produced on a steel sheet. An ensuing flat rolling pass is performed to create undercuts with a width of up to 50 µm, enabling an interlocking of the molten aluminium in the concluding casting process. For both rolling processes the resulting geometry is analysed depending on the thickness reduction. In a subsequent high pressure die casting process, aluminium is applied resulting in a complete form filling for the coarser structure. Comparing structures with and without undercuts, only structures suited with undercuts remain gap-free after solidification contraction. The finer structure could not be filled completely; nevertheless these structures result in shear strength of up to 45 MPa transversal to the channel-direction.

The correlation between microstructure and mechanical properties of high-pressure die-cast AM50 alloy

International Nuclear Information System (INIS)

Song Jie; Xiong Shoumei; Li Mei; Allison, John

2009-01-01

Scanning acoustic microscopy was used to characterize the micro-voids distribution for specimens in non-destructive mode. In addition, the in-situ scanning electron microscopy observation was performed during tensile deformation of high-pressure die-cast (HPDC) of AM50 alloy to obtain the mechanism of fracture induced by micro-voids. The effects of micro-voids on the mechanical properties were discussed. The results obtained from the examination suggest that fracture tends to occur at bigger micro-voids or in the cluster micro-voids area.

Case study of lean manufacturing application in a die casting manufacturing company

Science.gov (United States)

Ching, Ng Tan; Hoe, Clarence Chan Kok; Hong, Tang Sai; Ghobakhloo, Morteza; Pin, Chen Kah

2015-05-01

The case study of lean manufacturing aims to study the application of lean manufacturing in a die casting manufacturing company located in Pulau Penang, Malaysia. This case study describes mainly about the important concepts and applications of lean manufacturing which could gradually help the company in increasing the profit by studying and analyzing their current manufacturing process and company culture. Many approaches of lean manufacturing are studied in this project which includes: 5S housekeeping, Kaizen, and Takt Time. Besides, the lean tools mentioned, quality tool such as the House of Quality is being used as an analysis tool to continuously improve the product quality. In short, the existing lean culture in the company is studied and analyzed, with recommendations written at the end of this paper.

Comparison of marginal accuracy of castings fabricated by conventional casting technique and accelerated casting technique: an in vitro study.

Science.gov (United States)

Reddy, S Srikanth; Revathi, Kakkirala; Reddy, S Kranthikumar

2013-01-01

Conventional casting technique is time consuming when compared to accelerated casting technique. In this study, marginal accuracy of castings fabricated using accelerated and conventional casting technique was compared. 20 wax patterns were fabricated and the marginal discrepancy between the die and patterns were measured using Optical stereomicroscope. Ten wax patterns were used for Conventional casting and the rest for Accelerated casting. A Nickel-Chromium alloy was used for the casting. The castings were measured for marginal discrepancies and compared. Castings fabricated using Conventional casting technique showed less vertical marginal discrepancy than the castings fabricated by Accelerated casting technique. The values were statistically highly significant. Conventional casting technique produced better marginal accuracy when compared to Accelerated casting. The vertical marginal discrepancy produced by the Accelerated casting technique was well within the maximum clinical tolerance limits. Accelerated casting technique can be used to save lab time to fabricate clinical crowns with acceptable vertical marginal discrepancy.

75 FR 20387 - Contech Castings, LLC, Including Workers Whose Unemployment Insurance (UI) Wages Are Reported...

Science.gov (United States)

2010-04-19

... Apply for Worker Adjustment Assistance In accordance with Section 223 of the Trade Act of 1974, as... aluminum and magnesium die casted component parts for automobiles. New information shows that the assets of... workers of the subject firm who were adversely affected by increased imports of aluminum and magnesium die...

Effect of cast steel production metallurgy on the emergence of casting defects

Directory of Open Access Journals (Sweden)

L. Čamek

2016-10-01

Full Text Available The paper documents metallurgical possibilities of high alloy cast steel production in open induction medium frequency furnaces and an electric arc furnace in a gravity die casting foundry. The observation was focused on the emergence of gas defects in steel castings. The content of gases achieved during the metallurgical processes was evaluated for every unit of the production equipment and the casting ladle before casting into disposable sand moulds. The sand mould area was considered to be constant. The aim was to evaluate the current metallurgical possibilities of affecting the content of gases in high alloy cast steel in the current technical conditions of the foundry.

Effect of substituting cerium-rich mischmetal with lanthanum on high temperature properties of die-cast Mg-Zn-Al-Ca-RE alloys

International Nuclear Information System (INIS)

Anyanwu, Ifeanyi A.; Gokan, Yasuhiro; Suzuki, Atsuya; Kamado, Shigeharu; Kojima, Yo; Takeda, Suguru; Ishida, Taketoshi

2004-01-01

Mg-Zn-Al-Ca-RE alloys have been found to be promising materials for substituting aluminum alloys used for automatic transmission case applications in the automobile industry. Particularly, Mg-0.5%Zn-6%Al-1%Ca-3%RE (ZAXE05613) alloy exhibits comparable creep resistance as ADC12 die-casting aluminum alloy that is currently used for automatic transmission case applications. Changing the rare earth (RE) content of the alloy from mischmetal to lanthanum gives a further improvement in the creep properties of the alloy. Lanthanum addition results in the crystallization of a large amount of acicular Al 11 RE 3 (Al 11 La 3 ) compound along the grain boundaries as well as across the grain boundaries and this effectively controls grain boundary sliding and dislocation motion in the vicinity of the grain boundaries. As a result, die-cast ZAXLa05613 alloy exhibits a higher creep resistance than that of ZAXE05613 alloy

Ejection Performance of Coated Core Pins Intended for Application on High Pressure Die Casting Tools for Aluminium Alloys Processing

Directory of Open Access Journals (Sweden)

P. Terek

2017-09-01

Full Text Available In high pressure die casting (HPDC process of aluminium alloys cast alloy soldering severely damages tool surfaces. It hampers casting ejection, reduces the casting quality and decreases the overall production efficiency. Thin ceramic PVD (physical vapor deposition coatings applied on tool surfaces successfully reduce these effects. However, their performance is still not recognised for surfaces with various topographies. In this investigation, soldering tendency of Al-Si-Cu alloy toward EN X27CrMoV51 steel, plasma nitrided steel, CrN and TiAlN duplex PVD coatings is evaluated using ejection test. The coatings were prepared to a range of surface roughness and topographies. After the tests sample surfaces were analysed by different microscopy techniques and profilometry. It was found that the ejection performance is independent of the chemical composition of investigated materials. After the ejection, the cast alloy soldering layer was found on surfaces of all tested materials. This built-up layer formed by effects of mechanical soldering, without corrosion reactions. Coated samples displayed a pronounced dependence of ejection force on surface roughness and topography. By decreasing roughness, ejection force increased, which is a consequence of intensified adhesion effects. Presented findings are a novel information important for efficient application of PVD coatings intendent for protection of HPDC tools.

Reproduce and die! Why aging? Part II

NARCIS (Netherlands)

Schuiling, GA

Whilst in part I of this diptych on aging the question why aging exists at all is discussed; this part deals with the question which mechanisms underly aging and, ultimately, dying. It appears that aging is not just an active process as such - although all kinds of internal (e.g., oxigen-free

A new approach to assess the effects of Sr and Bi interaction in ADC12 Al–Si die casting alloy

International Nuclear Information System (INIS)

Farahany, Saeed; Ourdjini, Ali; Abu Bakar, Tuty Asma; Idris, Mohd Hasbullah

2014-01-01

Highlights: • Interactive effect between Bi and Sr has been invesitigated comprehensively. • Sequence of addition did not affect thermal and microscopical characteristics. • A new map has been established to assess the final microstructure of castings. - Abstract: In the present paper, the possible interaction between bismuth and strontium in ADC12 die casting alloy was investigated comprehensively by using in situ thermal analysis technique. The characteristic temperatures including nucleation, minimum and growth temperatures of eutectic Al–Si were also analyzed. The results show that with Bi present in the Al–Si alloy melt the efficiency of Sr in modifying the eutectic Si is reduced. A threshold Sr/Bi ratio of at least 0.5 is required for a fully modified Si structure to form. A new map based on the characteristic temperatures, Sr/Bi ratio and microstructure, was established to assess the microstructure of fully solidified Al–Si castings

A new approach to assess the effects of Sr and Bi interaction in ADC12 Al–Si die casting alloy

Energy Technology Data Exchange (ETDEWEB)

Farahany, Saeed, E-mail: saeedfarahany@gmail.com; Ourdjini, Ali; Abu Bakar, Tuty Asma; Idris, Mohd Hasbullah

2014-01-10

Highlights: • Interactive effect between Bi and Sr has been invesitigated comprehensively. • Sequence of addition did not affect thermal and microscopical characteristics. • A new map has been established to assess the final microstructure of castings. - Abstract: In the present paper, the possible interaction between bismuth and strontium in ADC12 die casting alloy was investigated comprehensively by using in situ thermal analysis technique. The characteristic temperatures including nucleation, minimum and growth temperatures of eutectic Al–Si were also analyzed. The results show that with Bi present in the Al–Si alloy melt the efficiency of Sr in modifying the eutectic Si is reduced. A threshold Sr/Bi ratio of at least 0.5 is required for a fully modified Si structure to form. A new map based on the characteristic temperatures, Sr/Bi ratio and microstructure, was established to assess the microstructure of fully solidified Al–Si castings.

Reengineering of Permanent Mould Casting with Lean Manufacturing Methods

Directory of Open Access Journals (Sweden)

R. Władysiak

2007-07-01

Full Text Available At the work were introduced main areas of production system project of casts produced in permanent moulds, that constitutes reengineering of conventional production system according to Lean Manufacturing (LM methods. New resolution of cooling of dies with water mist was shown to casting of car wheels made from aluminium alloys in low pressure casting process. It was implemented as a part of goal-oriented project in R.H. Alurad Sp.z o.o. in Gorzyce. Its using intensifies solidification and self-cooling of casts shortening the time of casting cycle by the 30%. It was described reorganizing casting stations into multi-machines cells production and the process of their fast tool’s exchange with applying the SMED method. A project of the system was described controlling the production of the foundry with the computer aided light Kanban system. A visualization of the process was shown the production of casts with use the value stream mapping method. They proved that applying casting new method in the technology and LM methods allowed to eliminate down-times, to reduce the level of stocks, to increase the productivity and the flow of the castings production.

Die-cast of a hypo-eutectic AL-SI alloy: influence of injection temperature on microstructure and mechanical properties; Fundicao sob pressao das ligas de AL-SI: influencia da temperatura de injecao nas microestruturas e propriedades mecanicas

Energy Technology Data Exchange (ETDEWEB)

Santos, Silvano Leal dos; Santos, Sydney Ferreira, E-mail: silvano_lleal@yahoo.com.br [Universidade Federal do ABC (UFABC), SP (Brazil)

2014-07-01

Die-casting is widely used for manufacturing light alloy components for automotive industry. Among others, hypo-eutectic Al-Si alloys are currently processed by die-casting. To obtain high quality die-cast components, a better understanding on the correlations between processing parameters, microstructures, and mechanical properties are of utmost importance. In this study, we investigate the effect of injection temperature of liquid metal on the microstructure and mechanical properties of Al-Si alloy EN AC 46000 (DIN designation). The injection temperatures were 579, 589, 643, and 709 deg C. As-cast components had their microstructures analyzed by X-ray diffraction, optical and scanning electron microscopy, and X-ray energy dispersive spectroscopy. The mechanical properties were examined by micro-hardness and tensile tests. It was observed that the ultimate tensile strength slightly increased with the increase of injection temperature. The same trend was observed for micro-hardness. The amount of porosity in the samples varies in a small amount for different injection temperatures. On the other hand, the microstructure of the alloys seems more refined for higher temperatures of injection. This refinement in microstructure might play a major role on the mechanical properties of the Al-Si die-cast alloy. (author)

Integrated Modeling of Process, Structures and Performance in Cast Parts

DEFF Research Database (Denmark)

Kotas, Petr

This thesis deals with numerical simulations of gravity sand casting processes for the production of large steel parts. The entire manufacturing process is numerically modeled and evaluated, taking into consideration mould filling, solidification, solid state cooling and the subsequent stress build...... and to defects occurrence. In other words, it is desired to eliminate all of the potential casting defects and at the same time to maximize the casting yield. The numerical optimization algorithm then takes these objectives and searches for a set of the investigated process, design or material parameters e.......g. chill design, riser design, gating system design, etc., which would satisfy these objectives the most. The first step in the numerical casting process simulation is to analyze mould filling where the emphasis is put on the gating system design. There are still a lot of foundry specialists who ignore...

A comparative evaluation of the marginal adaptation of a thermoplastic resin, a light cured wax and an inlay casting wax on stone dies: An in vitro study.

Science.gov (United States)

Gopalan, Reji P; Nair, Vivek V; Harshakumar, K; Ravichandran, R; Lylajam, S; Viswambaran, Prasanth

2018-01-01

Different pattern materials do not produce copings with satisfactory, marginal accuracy when used on stone dies at varying time intervals. The purpose of this study was to evaluate and compare the vertical marginal accuracy of patterns formed from three materials, namely, thermoplastic resin, light cured wax and inlay casting wax at three-time intervals of 1, 12, and 24 h. A master die (zirconia abutment mimicking a prepared permanent maxillary central incisor) and metal sleeve (direct metal laser sintering crown #11) were fabricated. A total of 30 stone dies were obtained from the master die. Ten patterns were made each from the three materials and stored off the die at room temperature. The vertical marginal gaps were measured using digital microscope at 1, 12, and 24 h after reseating with gentle finger pressure. The results revealed a significant statistical difference in the marginal adaptation of three materials at all the three-time intervals. Light cured wax was found to be most accurate at all time intervals, followed by thermoplastic resin and inlay casting wax. Furthermore, there was a significant difference between all pairs of materials. The change in vertical marginal gap from 1 to 24 h between thermoplastic resin and light cured wax was not statistically significant. The marginal adaptation of all the three materials used, was well within the acceptable range of 25-70 μm. The resin pattern materials studied revealed significantly less dimensional change than inlay casting wax on storage at 1, 12, and 24 h time intervals. They may be employed in situations where high precision and delayed investing is expected.

Optimization of Composition and Heat Treating of Die Steels for Extended Lifetime; FINAL

International Nuclear Information System (INIS)

David Schwam; John F, Wallace; Quanyou Zhou

2002-01-01

An ''average'' die casting die costs fifty thousand dollars. A die used in making die cast aluminum engine blocks can cost well over one million dollars. These costs provide a strong incentive for extension of die life. While vacuum quenched Premium Grade H13 dies have become the most widely used in the United States, tool makers and die casters are constantly searching for new steels and heat treating procedures to extend die life. This project was undertaken to investigate the effects of composition and heat treating on die life and optimize these parameters

Microstructural effects of phosphorus on pressure die cast Al-12Si components

Directory of Open Access Journals (Sweden)

Suárez-Peña, B.

2007-10-01

Full Text Available The refinement of cuboidal silicon in eutectic Al-Si alloys by phosphorus additions used to manufacture pressure die cast components was studied. The results show that the addition of phosphorus in the form of AlFeP mother alloy before process degassing, leads to the best refinement of the size of the Si-cuboids phase, among several phosphorus additions analysed in the present research.

Se ha estudiado el afino del silicio cuboidal en aleaciones eutécticas Al-Si por acción del fósforo, en piezas obtenidas mediante la técnica de fundición a presión. Tras la adición de fósforo en pruebas industriales, en las que dicho elemento se incorpora al baño con diversas composiciones, los mejores resultados se obtienen con la adición de la aleación madre AlFeP, previa al desgasificado industrial.

The Effect of Water Mist Cooling of Casting Die on the Solidification, Microstructure and Properties of AlSi20 Alloy

Directory of Open Access Journals (Sweden)

Władysiak R.

2017-03-01

Full Text Available Unmodified AlSi20 alloy were casted at the research station, allowing for sequential multipoint cooling using a dedicated computer- controlled program. This method allows for the formation of the microstructure of hypereutectic AlSi20 alloy and also increases hardness. Primary silicon dendrites were found in the microstructure of cooled samples. Based on these dendrites, the formation of primary silicon particles is explained. Cooling of casting die with a water mist stream causes changes in solidification, which leads to expansion of the boundary layer with columnar crystals and shrinkage of the core zone with equiaxed crystals. It also causes more regular hardness distribution around pre-eutectic Si crystals, which can lead to tensile strength and machinability improvement.

A Study on Development of High Strength Al-Zn Based alloy for Die Casting Ⅲ

Energy Technology Data Exchange (ETDEWEB)

Shin, Sang-Soo; Park, Ik-Min [Pusan National University, Busan (Korea, Republic of); Yeom, Gil-Young; Lim, Kyoung-Mook [Korea Institute of Industrial Technology, Incheon (Korea, Republic of); Son, Hyun-Jin [Oh-Sung Co. Ltd., Siheung (Korea, Republic of)

2015-09-15

In this study, the microstructural evolution and various characteristics of Al-20⁓45wt%Zn alloys were investigated. In terms of microstructure, as the amount of Zn addition to the alloys increased, the α-phase size decreased and the α+η non-equilibrium solidification phase fraction increased. Also, increasing Zn content improved the wear resistance of the alloys, but reduced the damping capacity and toughness of the alloys. Their physical properties of the Al-Zn alloy with high Zn content, specifically the wear resistance and toughness, were superior to those of commercial ALDC12 alloys for die-casting. Based on these results, we considered the possibility of application of the developed Al-Zn alloy as a structural material.

A Study on Development of High Strength Al-Zn Based alloy for Die Casting Ⅲ

International Nuclear Information System (INIS)

Shin, Sang-Soo; Park, Ik-Min; Yeom, Gil-Young; Lim, Kyoung-Mook; Son, Hyun-Jin

2015-01-01

In this study, the microstructural evolution and various characteristics of Al-20⁓45wt%Zn alloys were investigated. In terms of microstructure, as the amount of Zn addition to the alloys increased, the α-phase size decreased and the α+η non-equilibrium solidification phase fraction increased. Also, increasing Zn content improved the wear resistance of the alloys, but reduced the damping capacity and toughness of the alloys. Their physical properties of the Al-Zn alloy with high Zn content, specifically the wear resistance and toughness, were superior to those of commercial ALDC12 alloys for die-casting. Based on these results, we considered the possibility of application of the developed Al-Zn alloy as a structural material.

Casting traceability with direct part marking using reconfigurable pin-type tooling based on paraffin–graphite actuators

DEFF Research Database (Denmark)

Vedel-Smith, Nikolaj Kjelgaard; Lenau, Torben Anker

2012-01-01

Green sand moulding machines for cast iron foundries are presently unable to uniquely identify individual castings. An insert tool concept is developed and tested via incremental mock-up development. The tool is part of the pattern plate and changes shape between each moulding, thus giving each...... mould a unique ID by embossing a Data Matrix symbol into the sand. In the process of producing the mould, each casting can be given a unique (DPM), enabling part tracking throughout the casting's life cycle. Sand embossing is achieved with paraffin-actuated reconfigurable pin-type tooling under...... simulated processing conditions. The marker geometry limitations have been tested using static symbol patterns, both for sand embossing and actual casting marking. The marked castings have successfully been identified with decoding software. The study shows that the function of each element...

The potential of centrifugal casting for the production of near net shape uranium parts

International Nuclear Information System (INIS)

Robertson, E.

1993-09-01

This report was written to provide a detailed summary of a literature survey on the near net shape casting process of centrifugal casting. Centrifugal casting is one potential casting method which could satisfy the requirements of the LANL program titled Near Net Shape Casting of Uranium for Reduced Environmental, Safety and Health Impact. In this report, centrifugal casting techniques are reviewed and an assessment of the ability to achieve the near net shape and waste minimization goals of the LANL program by using these techniques is made. Based upon the literature reviewed, it is concluded that if properly modified for operation within a vacuum, vertical or horizontal centrifugation could be used to safely cast uranium for the production of hollow, cylindrical parts. However, for the production of components of geometries other than hollow tubes, vertical centrifugation could be combined with other casting methods such as semi-permanent mold or investment casting

Evaluating the Tensile Properties of Aluminum Foundry Alloys through Reference Castings-A Review.

Science.gov (United States)

Anilchandra, A R; Arnberg, Lars; Bonollo, Franco; Fiorese, Elena; Timelli, Giulio

2017-08-30

The tensile properties of an alloy can be exploited if detrimental defects and imperfections of the casting are minimized and the microstructural characteristics are optimized through several strategies that involve die design, process management and metal treatments. This paper presents an analysis and comparison of the salient characteristics of the reference dies proposed in the literature, both in the field of pressure and gravity die-casting. The specimens produced with these reference dies, called separately poured specimens, are effective tools for the evaluation and comparison of the tensile and physical behaviors of Al-Si casting alloys. Some of the findings of the present paper have been recently developed in the frame of the European StaCast project whose results are complemented here with some more recent outcomes and a comprehensive analysis and discussion.

Rapid die manufacturing using direct laser metal deposition

CSIR Research Space (South Africa)

Pereira, MFVT

2009-01-01

Full Text Available This paper highlights the work undertaken at the CSIR on the issue of rapid die manufacturing through the application and evaluation of a rapid prototyping technique and coating technologies applied to die components of a high pressure casting die...

Weight reduction of automobile parts using light metals. Keikinzoku shiyo ni yoru jidosha buhin no keiryoka

Energy Technology Data Exchange (ETDEWEB)

Hayashi, S [Toyota Motor Corp., Aichi (Japan)

1992-12-25

Weight reduction of automobiles is required from the viewpoint of reduction of CO2 emission and energy conservation. Comparing a car with another one of almost the same size and performance with 1% reduced weight, combustion efficiency of the latter can be improved by 0.5-0.8%. This report introduces several examples, in which steel parts are replaced with light alloy parts to reduce car weight, and describes the future perspective. Concerning a cylinder block which is the heaviest part among engine parts, a block made of aluminum alloy with no cast liner has been developed. There is also an example of an oil pan adopting aluminum die-cast for a part of it. A valve lifter made of aluminum alloy has been developed for valve system parts and has contributed to friction loss, noise reduction, and improvement of fuel consumption. As for steering system parts, a steering bracket made of Mg alloy die-cast has been developed. The use of light alloy parts, in general, increases material cost. Therefore it is now required to build up closer connection between designs and production techniques and to improve reliability of casting and forging technologies. 5 refs., 20 figs.

Modelling of Filling, Microstructure Formation, Local Mechanical Properties and Stress – Strain Development in High-Pressure Die Cast Aluminium Castings

DEFF Research Database (Denmark)

Kotas, Petr; Hattel, Jesper Henri; Thorborg, Jesper

2009-01-01

.e. whether the casting is based on cast iron- or aluminium-alloys. The distribution of local properties in a casting might vary substantially which makes it complex to optimize the casting with good accuracy. Often, mechanical simulations of the load situation are based on the assumption that the cast...... in an aluminium alloy is considered including simulation of the entire casting process with emphasis on microstructure formation related to mechanical properties such as elastic modulus, yield stress, ultimate strength and elongation as well as residual stresses. Subsequently, the casting is subjected to service...... loads and the results of this analysis are discussed in relation to the predicted local properties as well as the residual stresses originating from the casting simulation....

Fabrication of sacrificial anode cathodic protection through casting method

International Nuclear Information System (INIS)

Mohd Sharif Sattar; Muhamad Daud; Siti Radiah Mohd Kamarudin; Azali Muhamad; Zaiton Selamat; Rusni Rejab

2007-01-01

Aluminum is one of the few metals that can be cast by all of the processes used in casting metals. These processes consist of die casting, permanent mold casting, sand casting (green sand and dry sand), plaster casting, investment casting, and continuous casting. Other processes such as lost foam, squeeze casting, and hot isostatic pressing are also used. Permanent mold casting method was selected in which used for fabricating of sacrificial anode cathodic protection. This product was ground for surface finished and fabricated in the cylindrical form and reinforced with carbon steel at a center of the anode. (Author)

Influence of polyurethane resin dies on the fit and adaptation of full veneer crowns.

Science.gov (United States)

Lillywhite, Graeme R R; Vohra, Fahim

2015-01-01

Polyurethane resin is a possible alternative to type IV dental stone for fabrication of indirect restorations however its dimensional accuracy is questionable. The aim was to investigate the dimensional accuracy of silica filled polyurethane resin die material by evaluating the marginal fit and adaptation of indirect gold castings. Experimental, in vitro study. Totally 40 copper plated replicas of a nickel chrome master die analogous to a veneer gold crown preparation were made and impressions recorded using polyvinylsiloxane material. Twenty impressions were poured in type IV dental stone (control group (Vel-mix, Kerr, UK) and the remaining (n = 20) in silica filled polyurethane die material (test group) (Alpha Die MF, CA, USA). Gold castings were fabricated for each die using standardized techniques. The castings were seated on their respective copper plated dies, embedded in resin and sectioned. The specimens were analyzed by measuring marginal opening and the area beneath the casting at a ×63 magnification and using image analysis software. Data were analyzed using a Student's t-test. No significant difference was observed between the experimental groups (P > 0.05). The mean marginal opening for type IV, dental stone and polyurethane resin, was 57 ± 22.6 μm and 63.47 ± 27.1 μm, respectively. Stone displayed a smaller area beneath the casting (31581 ± 16297 μm 2 ) as compared to polyurethane resin (35003 ± 23039 μm 2 ). The fit and adaptation of indirect gold castings made on polyurethane and type IV dental stone dies were comparable.

Marginal Accuracy of Castings Produced with Different Investment Systems.

Science.gov (United States)

Yadav, R K

2009-04-01

The use of casting ring to produce accurate castings has been challenged with the introduction of a ringless casting technique. This study compared the marginal accuracy of all - metal complete coverage crowns fabricated with ringless, split plastic ring and metal ring investment systems. A total of 40 all- metal complete coverage crowns were fabricated on a metal die. The crowns were divided in 4 groups (Group A, B, C and D) of 10 patterns each. A ringless system of investing and casting was used for group A whereas a split plastic ring system was used for group B. Groups C and D utilized metal ring with single and double layers of asbestos free cellulose acetate liner respectively for investing and casting procedures. The restorations were seated on the metal die and the vertical marginal discrepancy was evaluated by measuring the gap between the finish line on the die and the margins of the crown on four specific sites with an optical microscope. Statistical analysis was carried out using ANOVA and multiple comparison "t" test. The mean vertical marginal discrepancy for groups A, B, C and D was 95μm, 136μm, 128μm and 104μm respectively. Vertical marginal discrepancy on each surface was compared among the four groups. Difference of vertical marginal discrepancy on buccal surface (p0.05). Accurate castings with better marginal fit can be produced with ringless casting technique.

Microstructural stability of heat-resistant high-pressure die-cast Mg-4Al-4Ce alloy

Energy Technology Data Exchange (ETDEWEB)

Wang, Wei; Zhang, Jinghuai; Li, Guoqiang; Feng, Yan; Su, Minliang; Wu, Ruizhi; Zhang, Zhongwu [Harbin Engineering Univ. (China). Key Laboratory of Superlight Material and Surface Technology; Jiao, Yufeng [Jiamusi Univ. (China). College of Materials Science and Engineering

2017-05-15

The thermal stability of Al-RE (rare earth) intermetallic phases with individual RE for heat-resistant high-pressure die-casting Mg-Al-RE alloys is investigated. The results of this study show that the main strengthening phase of Mg-4Al-4Ce alloy is Al{sub 11}Ce{sub 3}, whose content is about 5 wt.% according to quantitative X-ray diffraction phase analysis. The Al{sub 11}Ce{sub 3} phase appears to have high thermal stability at 200 C and 300 C, while phase morphology change with no phase structure transition could occur for Al{sub 11}Ce{sub 3} when the temperature reaches 400 C. Furthermore, besides the kinds of rare earths and temperature, stress is also an influencing factor in the microstructural stability of Mg-4Al-4Ce alloy.

Optimization of squeeze casting parameters for non symmetrical AC2A aluminium alloy castings through Taguchi method

International Nuclear Information System (INIS)

Senthil, P.; Amirthagadeswaran, K. S.

2012-01-01

This paper reports a research in which an attempt was made to prepare AC2A aluminium alloy castings of a non symmetrical component through squeeze casting process. The primary objective was to investigate the influence of process parameters on mechanical properties of the castings. Experiments were conducted based on orthogonal array suggested in Taguchi's offline quality control concept. The experimental results showed that squeeze pressure, die preheating temperature and compression holding time were the parameters making significant improvement in mechanical properties. The optimal squeeze casting condition was found and mathematical models were also developed for the process

Multi-Objective Optimization of Squeeze Casting Process using Genetic Algorithm and Particle Swarm Optimization

Directory of Open Access Journals (Sweden)

Patel G.C.M.

2016-09-01

Full Text Available The near net shaped manufacturing ability of squeeze casting process requiresto set the process variable combinations at their optimal levels to obtain both aesthetic appearance and internal soundness of the cast parts. The aesthetic and internal soundness of cast parts deal with surface roughness and tensile strength those can readily put the part in service without the requirement of costly secondary manufacturing processes (like polishing, shot blasting, plating, hear treatment etc.. It is difficult to determine the levels of the process variable (that is, pressure duration, squeeze pressure, pouring temperature and die temperature combinations for extreme values of the responses (that is, surface roughness, yield strength and ultimate tensile strength due to conflicting requirements. In the present manuscript, three population based search and optimization methods, namely genetic algorithm (GA, particle swarm optimization (PSO and multi-objective particle swarm optimization based on crowding distance (MOPSO-CD methods have been used to optimize multiple outputs simultaneously. Further, validation test has been conducted for the optimal casting conditions suggested by GA, PSO and MOPSO-CD. The results showed that PSO outperformed GA with regard to computation time.

Mechanism and application of a newly developed pressure casting process: horizontal squeeze casting

Directory of Open Access Journals (Sweden)

Li Peijie

2014-07-01

Full Text Available Compared to traditional high-pressure die casting (HPDC, horizontal squeeze casting (HSC is a more promising way to fabricate high-integrity castings, owing to a reduced number of gas and shrinkage porosities produced in the casting. In this paper, the differences between HSC and HPDC are assessed, through which it is shown that the cavity filling velocity and the size of the gating system to be the most notable differences. Equipment development and related applications are also reviewed. Furthermore, numerical simulation is used to analyze the three fundamental characteristics of HSC: slow cavity filling, squeeze feeding and slow sleeve filling. From this, a selection principle is given based on the three related critical casting parameters: cavity filling velocity, gate size and sleeve filling velocity. Finally, two specific applications of HSC are introduced, and the future direction of HSC development is discussed.

Analysis of the creep behaviour of die-cast Mg–3Al–1Si alloy

Energy Technology Data Exchange (ETDEWEB)

Zhu, S.M., E-mail: suming.zhu@monash.edu [CAST Cooperative Research Centre, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); ARC Centre of Excellence for Design in Light Metals, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); Easton, M.A. [CAST Cooperative Research Centre, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); Gibson, M.A. [CAST Cooperative Research Centre, CSIRO Process Science and Engineering, Clayton, Victoria 3169 (Australia); Dargusch, M.S. [Centre for Advanced Materials Processing and Manufacturing, School of Mechanical and Mining Engineering, The University of Queensland, Queensland 4075 (Australia); Defence Materials Technology Centre, The University of Queensland, Queensland 4075 (Australia); Nie, J.F. [ARC Centre of Excellence for Design in Light Metals, Department of Materials Engineering, Monash University, Victoria 3800 (Australia)

2013-08-20

The creep behaviour of die-cast Mg–3Al–1Si (AS31) alloy has been studied at 125 °C, 150 °C and 175 °C with stresses ranging 50–110 MPa. The alloy exhibits anomalously high stress exponents, i.e. 14.4 at 125 °C, 11.6 at 150 °C and 9.5 at 175 °C. Contrary to work reported previously, these high stress exponents cannot be rationalised using the threshold stress approach that is commonly adopted in analysing creep behaviour of dispersion strengthened alloys or metal matrix composites. It is shown that the observed high stress exponents are associated with the dominance of power-law breakdown creep in this study, and the stress dependence can be well described by the Garofalo sinh relationship with the natural exponent of 5. Transmission electron microscopy (TEM) observations reveal that cross-slip of 〈a〉 type dislocations is probably the controlling creep mechanism.

Analysis of the creep behaviour of die-cast Mg–3Al–1Si alloy

International Nuclear Information System (INIS)

Zhu, S.M.; Easton, M.A.; Gibson, M.A.; Dargusch, M.S.; Nie, J.F.

2013-01-01

The creep behaviour of die-cast Mg–3Al–1Si (AS31) alloy has been studied at 125 °C, 150 °C and 175 °C with stresses ranging 50–110 MPa. The alloy exhibits anomalously high stress exponents, i.e. 14.4 at 125 °C, 11.6 at 150 °C and 9.5 at 175 °C. Contrary to work reported previously, these high stress exponents cannot be rationalised using the threshold stress approach that is commonly adopted in analysing creep behaviour of dispersion strengthened alloys or metal matrix composites. It is shown that the observed high stress exponents are associated with the dominance of power-law breakdown creep in this study, and the stress dependence can be well described by the Garofalo sinh relationship with the natural exponent of 5. Transmission electron microscopy (TEM) observations reveal that cross-slip of 〈a〉 type dislocations is probably the controlling creep mechanism

Evaluations of antimony and strontium interaction in an Al–Si–Cu–Zn die cast alloy

Energy Technology Data Exchange (ETDEWEB)

Farahany, Saeed, E-mail: saeedfarahany@gmail.com; Idris, Mohd Hasbullah; Ourdjini, Ali

2014-05-01

Graphical abstract: - Highlights: • Probable interactions between Sb and Sr in a complex Al–Si alloy were evaluated. • Sequence of addition did not affect thermal and microscopical characteristics. • Threshold ratio for the Sb and Sr interaction is proposed. - Abstract: The interaction between antimony and strontium in an ADC12 die casting alloy is investigated comprehensively by using a computer aided cooling curve thermal analysis coupled with microstructure inspection. The results of the thermal analysis show significant changes in Al–Si eutectic reaction based on different concentrations of Sb and Sr. Sb reduces the efficiency of Sr in modifying the eutectic Si. Based upon the data obtained in this study, the threshold Sr/Sb ratio should exceed about 0.5 in order to obtain fully modified structure. Moreover, a pre-eutectic reaction of Al{sub 2}Si{sub 2}Sr intermetallic was detected for high concentrations of Sr.

Microstructural and mechanical properties of gravity-die-cast A356 alloy inoculated with yttrium and Al-Ti-B grain refiner simultaneously

Directory of Open Access Journals (Sweden)

Y.P. Lim

2011-10-01

Full Text Available In the present work, the effect of inoculating yttrium and Al-5Ti-1B simultaneously on A356 aluminum alloy has been studied. Gravity die casting process is used to cast the ASTM tensile test specimens for analysis. In each experiment, the Ti and B contents were maintained constantly at 0.1 and 0.02 wt% respectively. The addition of yttrium was manipulated at the amount of 0, 0.1, 0.2, 0.3, 0.4 and 0.5 wt%. Microstructural characterization of the as-cast A356 alloy was investigated by means of optical microscope and its phases are detected by XRD. The mechanical properties tested are tensile strength and hardness. The inoculation of yttrium was found to enhance the grain refinement effect of Al-5Ti-1B grain refiner and improve the mechanical properties. The optimal weight percentage of yttrium was found to be 0.3. The grain refining efficiency of combining yttrium and Al-5Ti-1B on A356 aluminum alloy was mainly attributed to the heterogeneous nucleation of TiB2 and TiAl3 particles which were dispersed more evenly in the presence of yttrium and the grain growth restriction effected by the accumulation of Al-Y compound at grain boundaries.

A simplified simulation model for a HPDC die with conformal cooling channels

Science.gov (United States)

Frings, Markus; Behr, Marek; Elgeti, Stefanie

2017-10-01

In general, the cooling phase of the high-pressure die casting process is based on complex physical phenomena: so-lidification of molten material; heat exchange between cast part, die and cooling fluid; turbulent flow inside the cooling channels that needs to be considered when computing the heat flux; interdependency of properties and temperature of the cooling liquid. Intuitively understanding and analyzing all of these effects when designing HPDC dies is not feasible. A remedy that has become available is numerical design, based for example on shape optimization methods. However, current computing power is not sufficient to perform optimization while at the same time fully resolving all physical phenomena. But since in HPDC suitable objective functions very often lead to integral values, e.g., average die temperature, this paper identifies possible simplifications in the modeling of the cooling phase. As a consequence, the computational effort is reduced to an acceptable level. A further aspect that arises in the context of shape optimization is the evaluation of shape gradients. The challenge here is to allow for large shape deformations without remeshing. In our approach, the cooling channels are described by their center lines. The flow profile of the cooling fluid is then estimated based on experimental data found in literature for turbulent pipe flows. In combination, the heat flux throughout cavity, die, and cooling channel can be described by one single advection-diffusion equation on a fixed mesh. The parameters in the equation are adjusted based on the position of cavity and cooling channel. Both results contribute towards a computationally efficient, yet accurate method, which can be employed within the frame of shape optimization of cooling channels in HPDC dies.

New sulphiding method for steel and cast iron parts

Science.gov (United States)

Tarelnyk, V.; Martsynkovskyy, V.; Gaponova, O.; Konoplianchenko, Ie; Dovzyk, M.; Tarelnyk, N.; Gorovoy, S.

2017-08-01

A new method for sulphiding steel and cast iron part surfaces by electroerosion alloying (EEA) with the use of a special electrode is proposed, which method is characterized in that while manufacturing the electrode, on its surface, in any known manner (punching, threading, pulling, etc.), there is formed at least a recess to be filled with sulfur as a consistent material, and then there is produced EEA by the obtained electrode without waiting for the consistent material to become dried.

The influence of flushing time on the bonding quality of liquid white cast iron on the solid surface of similar material

Science.gov (United States)

Bandanadjaja, Beny; Purwadi, Wiwik; Idamayanti, Dewi; Lilansa, Noval; Hanaldi, Kus; Nurzaenal, Friya Kurnia

2018-05-01

Hard metal castings are widely used in the coal mill pulverizer as construction material for coal crushers. During its operation crushers and mills experience degradation caused by abrasion load. This research dealed with the surface overlaying of similiar material on the surface of white cast iron by mean of gravity casting. The die blank casting was preheated prior to the casting process of outer layer made of Ni-Hard white cast iron to guarantee bonding processes and avoid any crack. The preheating temperature of die blankin ther range of 500C up to 850C was set up to reach the interface temperature in the range of 887°C -1198°C and the flushing time was varied between 10-20 seconds. Studies carried on the microstructure of sample material revealed a formation of metallurgical bonding at the preheating temperature above 625 °C by pouring temperature ranging from 1438 °C to 1468 °C. Metallographical and chemical composition by mean of EDS examination were performed to observed the resut. This research concludes that the casting of Ni-Hard 1 overlay by applying gravity casting method can be done by preheating the surface of casting to 625 °C, interface temperature of 1150 °C, flushing time of 7 seconds and pouring temperature of 1430 °C. Excellent metallurgical bonding at the contact area between dieblank and overlay material has been achieved in which there is no parting line at the interface area to be observed.

Clean Metal Casting

Energy Technology Data Exchange (ETDEWEB)

Makhlouf M. Makhlouf; Diran Apelian

2002-02-05

The objective of this project is to develop a technology for clean metal processing that is capable of consistently providing a metal cleanliness level that is fit for a given application. The program has five tasks: Development of melt cleanliness assessment technology, development of melt contamination avoidance technology, development of high temperature phase separation technology, establishment of a correlation between the level of melt cleanliness and as cast mechanical properties, and transfer of technology to the industrial sector. Within the context of the first task, WPI has developed a standardized Reduced Pressure Test that has been endorsed by AFS as a recommended practice. In addition, within the context of task1, WPI has developed a melt cleanliness sensor based on the principles of electromagnetic separation. An industrial partner is commercializing the sensor. Within the context of the second task, WPI has developed environmentally friendly fluxes that do not contain fluorine. Within the context of the third task, WPI modeled the process of rotary degassing and verified the model predictions with experimental data. This model may be used to optimize the performance of industrial rotary degassers. Within the context of the fourth task, WPI has correlated the level of melt cleanliness at various foundries, including a sand casting foundry, a permanent mold casting foundry, and a die casting foundry, to the casting process and the resultant mechanical properties. This is useful in tailoring the melt cleansing operations at foundries to the particular casting process and the desired properties of cast components.

Cast erosion from the cleaning of debris after the use of a cast trimmer.

Science.gov (United States)

Hansen, Paul A; Beatty, Mark W

2017-02-01

Whether using tap water to rinse off debris will make a clinical difference to the surface detail of a gypsum cast is unknown. In addition, how best to remove debris from the cast is unknown. The purpose of this in vitro study was to evaluate the efficiency of different methods of cleaning a gypsum cast after trimming and the effect of short-term exposure to tap water on the surface quality of the cast. A die fitting American National Standards Institute/American Dental Association specification 25 (International Standards Organization specification 6873) for dental gypsum products was embedded in a Dentoform with the machined lines positioned at the same level as the occlusal surface of the posterior teeth. A flat plate was used to ensure that the plane of occlusion for the die was at the same position as the posterior teeth. Forty polyvinyl siloxane impressions of the Dentoform were made and poured with vacuum-mixed improved Type IV dental stone. Each cast was inspected for the accurate reproduction of the lines. The base of the 2-stage pour was trimmed with a cast trimmer with water, and surface debris was removed by rinsing by hand under tap water for 10 seconds, by brushing the cast with a soft toothbrush for 10 seconds, or by resoaking the cast and using a soft camel hair brush in slurry water for 10 seconds. The amount of debris was evaluated on a scale of 1 to 4, and the quality of the 20-μm line was evaluated on a scale of 1 to 4 under ×15 magnification. The nonparametric Kruskal-Wallis ranks test was used to identify significant differences among the different cleaning methods (α=.05). Results of the Kruskal-Wallis and Kruskal-Wallis Z-value tests demonstrated that all cleaning methods produced cleaner casts than were observed for uncleansed controls (P<.001), but no differences in debris removal were found among the different cleaning methods (.065≤P≤.901). The ability to see the quality of a 20-μm line (P=.974) was not statistically different

Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties

Science.gov (United States)

Kuo, Chin-Guo; Chang, Ho; Wang, Jian-Hao

2016-01-01

In this investigation, anodic aluminum oxide (AAO) with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn) into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO) nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA. PMID:27023546

Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties.

Science.gov (United States)

Kuo, Chin-Guo; Chang, Ho; Wang, Jian-Hao

2016-03-24

In this investigation, anodic aluminum oxide (AAO) with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn) into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO) nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA.

REDUCING REJECTION/REWORK IN PRESSURE DIE CASTING PROCESS BY APPLICATION OF DMAIC METHODOLOGY OF SIX SIGMA

Directory of Open Access Journals (Sweden)

Javedhusen Malek

2015-12-01

Full Text Available In today's ever-changing customer driven market, industries are needed to improve their products and processes to satisfy customer requirements. The Six Sigma approach has set a new paradigm of business excellence. Six Sigma as a process driven improvement methodology has been adopted successfully by many industries. From the review of various literatures, it is revealed that Six Sigma is well adopted in large scale enterprise but having less evidence of adoption in Indian SMEs. This paper is focused on providing path to Indian SMEs for initiating Six Sigma approach in their industries. The paper discusses the real life case where Six Sigma has been successfully applied at one of the Indian small-scale unit to improve rejection/rework rate in manufacturing products by pressure die casting process. This paper describes phase wise application of all the phases of define-measure-analyse-improve-control (DMAIC which also shows impact of Six Sigma in quality improvement.

Die spel van assosiasies in en om 'Die verlossing van die beeld' van Breyten Breytenbach

Directory of Open Access Journals (Sweden)

P.A. du Toit

2005-07-01

Full Text Available The play of association in and around 'The liberation of the image' by Breyten Breytenbach This analysis focuses on the conjunction of memory and imagination, which is an important impulse in, and key to, Breytenbach’s work. The play with language and with associations, the foregrounding, in the short story, “Die verlossing van die beeld” (Breytenbach, 1983 with its metafictional title and apparently divergent motifs (rain/water, watch, onion, the death and burial of a grandfather acts, as it were, as an invitation to the reader to become a co-player. The reader ventures on a search for traces, intertextual links within the Breytenbach oeuvre and for already acknowledged influences such as Surrealism (which in turn casts some light on the strange title of the story and the Eastern philosophies such as Zen and the even older Taoism. The analysis also takes into account the context in which “Mouroir” was written, namely Breytenbach’s term in prison (1975-1982. Seeing that the writer had to hand in his manuscripts to the jail authorities regularly, he might have decided, consciously or by intuition, to hide some thoughts and feelings behind a screen or a mask, in, for example in “Die verlossing van die beeld”, a lighter tone and irony.

Application of optical scanning for measurements of castings and cores

Directory of Open Access Journals (Sweden)

M. Wieczorowski

2010-01-01

Full Text Available In the paper application of non destructive method for dimensional control of elements in initial phase of car manufacturing, at Volks-wagen Poznań foundry was presented. VW foundry in Poznań is responsible of series production of chill and dies castings made of light alloys using contemporary technologies. Castings have a complex shape: they are die castings of housings for steering columns and gravity chill castings of cylinder heads, for which cores are manufactured using both hot box and cold box method. Manufacturing capabilities of VW foundry in Poznań reach 26.000 tons of aluminum castings per year. Optical system ATOS at Volkswagen Poznań foundry is used to digitize object and determination of all dimensions and shapes of inspected object. This technology is applied in car industry, reverse engineering, quality analysis and control and to solve many similar tasks. System is based on triangulation: sensor head projects different fringes patterns onto a measured object while scanner observes their trajectories using two cameras. Basing on optical transform equations a processing unit automatically and with a great accuracy calculates 3D coordinates for every pixel of camera. Depending on camera reso-lution as an effect of such a scan we obtain a cloud of up to 4 million points for every single measurement. In the paper examples of di-mensional analysis regarding castings and cores were presented.

Fabrication of ZnO Nanowires Arrays by Anodization and High-Vacuum Die Casting Technique, and Their Piezoelectric Properties

Directory of Open Access Journals (Sweden)

Chin-Guo Kuo

2016-03-01

Full Text Available In this investigation, anodic aluminum oxide (AAO with arrayed and regularly arranged nanopores is used as a template in the high-vacuum die casting of molten zinc metal (Zn into the nanopores. The proposed technique yields arrayed Zn nanowires with an aspect ratio of over 600. After annealing, arrayed zinc oxide (ZnO nanowires are obtained. Varying the anodizing time yields AAO templates with thicknesses of approximately 50 μm, 60 μm, and 70 μm that can be used in the fabrication of nanowires of three lengths with high aspect ratios. Experimental results reveal that a longer nanowire generates a greater measured piezoelectric current. The ZnO nanowires that are fabricated using an alumina template are anodized for 7 h and produce higher piezoelectric current of up to 69 pA.

Low Cost Al-Si Casting Alloy As In-Situ Composite for High Temperature Applications

Science.gov (United States)

Lee, Jonathan A.

2000-01-01

A new aluminum-silicon (Al-Si) alloy has been successfully developed at NASA- Marshall Space Flight Center (MSFC) that has significant improvement in tensile and fatigue strength at elevated temperatures (500 F-700 F). The alloy offers a number of benefits such as light weight, high hardness, low thermal expansion and high surface wear resistance. In hypereutectic form, this alloy is considered as an in-situ Al-Si composite with tensile strength of about 90% higher than the auto industry 390 alloy at 600 F. This composite is very economically produced by using either conventional permanent steel molds or die casting. The projected material cost is less than $0.90 per pound, and automotive components such as pistons can be cast for high production rate using conventional casting techniques with a low and fully accounted cost. Key Words: Metal matrix composites, In-situ composite, aluminum-silicon alloy, hypereutectic alloy, permanent mold casting, die casting.

Clean Metal Casting; FINAL

International Nuclear Information System (INIS)

Makhlouf M. Makhlouf; Diran Apelian

2002-01-01

The objective of this project is to develop a technology for clean metal processing that is capable of consistently providing a metal cleanliness level that is fit for a given application. The program has five tasks: Development of melt cleanliness assessment technology, development of melt contamination avoidance technology, development of high temperature phase separation technology, establishment of a correlation between the level of melt cleanliness and as cast mechanical properties, and transfer of technology to the industrial sector. Within the context of the first task, WPI has developed a standardized Reduced Pressure Test that has been endorsed by AFS as a recommended practice. In addition, within the context of task1, WPI has developed a melt cleanliness sensor based on the principles of electromagnetic separation. An industrial partner is commercializing the sensor. Within the context of the second task, WPI has developed environmentally friendly fluxes that do not contain fluorine. Within the context of the third task, WPI modeled the process of rotary degassing and verified the model predictions with experimental data. This model may be used to optimize the performance of industrial rotary degassers. Within the context of the fourth task, WPI has correlated the level of melt cleanliness at various foundries, including a sand casting foundry, a permanent mold casting foundry, and a die casting foundry, to the casting process and the resultant mechanical properties. This is useful in tailoring the melt cleansing operations at foundries to the particular casting process and the desired properties of cast components

ASSESSMENT OF SURFACE FINISH AND DIMENSIONAL ACCURACY OF TOOLS MANUFACTURED BY METAL CASTING IN RAPID PROTOTYPING SAND MOULDS

Directory of Open Access Journals (Sweden)

Nyembwe, K.

2012-11-01

Full Text Available In this paper, an initial assessment of the quality parameters of the surface finish and dimensional accuracy of tools made by metal casting in rapid prototyping (RP sand moulds is undertaken. A case study from a local tool room, dealing with the manufacturing of an aluminium die for the lost wax process, is employed. Modern techniques, including surface roughness analysis and three dimensional scanning, are used to determine and understand how each manufacturing step influences the final quality of the cast tool. The best surface finish obtained for the cast die had arithmetic average roughness (Ra and mean average roughness (Rz respectively equal to 3.23m and 11.38m. In terms of dimensional accuracy, 82% of cast-die points coincided with the Computer Aided Design (CAD data, which is within the typical tolerances of sand cast products. The investigation shows that mould coating contributes slightly to the improvement of the cast tool surface finish. The study also found that the additive manufacturing of the sand mould was the chief factor responsible for the loss of dimensional accuracy. These findings indicate that machining will always be required to improve the surface finish and the dimensional accuracy of cast tools in RP sand moulds.

Microstructure, Tensile Properties, and Corrosion Behavior of Die-Cast Mg-7Al-1Ca- xSn Alloys

Science.gov (United States)

Wang, Feng; Dong, Haikuo; Sun, Shijie; Wang, Zhi; Mao, Pingli; Liu, Zheng

2018-02-01

The microstructure, tensile properties, and corrosion behavior of die-cast Mg-7Al-1Ca- xSn ( x = 0, 0.5, 1.0, and 2.0 wt.%) alloys were studied using OM, SEM/EDS, tensile test, weight loss test, and electrochemical test. The experimental results showed that Sn addition effectively refined grains and intermetallic phases and increased the amount of intermetallic phases. Meanwhile, Sn addition to the alloys suppressed the formation of the (Mg,Al)2Ca phase and resulted in the formation of the ternary CaMgSn phase and the binary Mg2Sn phase. The Mg-7Al-1Ca-0.5Sn alloy exhibited best tensile properties at room temperature, while Mg-7Al-1Ca-1.0Sn alloy exhibited best tensile properties at elevated temperature. The corrosion resistance of studied alloys was improved by the Sn addition, and the Mg-7Al-1Ca-0.5Sn alloy presented the best corrosion resistance.

Development of polymer nano composite patterns using fused deposition modeling for rapid investment casting process

Science.gov (United States)

Vivek, Tiwary; Arunkumar, P.; Deshpande, A. S.; Vinayak, Malik; Kulkarni, R. M.; Asif, Angadi

2018-04-01

Conventional investment casting is one of the oldest and most economical manufacturing techniques to produce intricate and complex part geometries. However, investment casting is considered economical only if the volume of production is large. Design iterations and design optimisations in this technique proves to be very costly due to time and tooling cost for making dies for producing wax patterns. However, with the advent of Additive manufacturing technology, plastic patterns promise a very good potential to replace the wax patterns. This approach can be very useful for low volume production & lab requirements, since the cost and time required to incorporate the changes in the design is very low. This research paper discusses the steps involved for developing polymer nanocomposite filaments and checking its suitability for investment castings. The process parameters of the 3D printer machine are also optimized using the DOE technique to obtain mechanically stronger plastic patterns. The study is done to develop a framework for rapid investment casting for lab as well as industrial requirements.

Microstructural and mechanical properties investigation of Mg-Al-Zn alloy counter gravity investment cast

CSIR Research Space (South Africa)

Mutombo, K

2009-10-01

Full Text Available . The most common manufacturing method for the production of Mg components is via High Pressure Die Casting (HPDC), however, this process is suitable for high volume thin walled components. Investment casting offers the capability of producing complex near...

Microstructure, Mechanical and Surface Morphological Properties of Al5Ti5Cr Master Alloy as Friction Material Prepared by Stir Die Casting

Science.gov (United States)

Ahmed, Syed Faisal; Srivastava, Sanjay; Agarwal, Alka Bani

2018-04-01

Metal matrix composite offers outstanding properties for better performance of disc brakes. In the present study, the composite of AlTiCr master alloy was prepared by stir die casting method. The developed material was reinforced with (0-10 wt%) silicon carbide (SiC) and boron carbide (B4C). The effects of SiC reinforcement from 0 to 10 wt% on mechanical, microstructure and surface morphological properties of Al MMC was investigated and compared with B4C reinforcement. Physical properties like density and micro Vickers hardness number show an increasing trend with an increase in the percentage of SiC and B4C reinforcement. Mechanical properties viz. UTS, yield strength and percentage of elongation are improved with increasing the fraction of reinforcement. The surface morphology and phase were identified from scanning electron microscopy (SEM) and X-ray diffraction analysis and the oxidized product formed during the casting was investigated by Fourier transformation infrared spectroscopy. This confirms the presence of crystallization of corundum (α-Al2O3) in small traces as one of the alumina phases, within casting sample. Micro-structural characterization by SEM depicted that the particles tend to be more agglomerated more and more with the percentage of the reinforcement. The AFM results reveal that the surface roughness value shows a decreasing trend with SiC reinforcement while roughness increases with increase the percentage of B4C.

A comparative evaluation of linear dimensional accuracy of the dies obtained using three conceptually different die systems in the fabrication of implant prosthesis: An in vitro study

Directory of Open Access Journals (Sweden)

Manawar Ahmad

2014-01-01

Purpose: The purpose of the study was to evaluate the linear dimensional accuracy between the implant master die and three conceptually different die systems such as Pindex system, Accu-trac precision die system, and Conventional brass dowel pin system. Materials and Methods: Thirty impressions of implant master die were made with polyether impression material. Ten experimental implant casts were fabricated for each of the three different die systems tested: Accu-trac precision die tray system, Pindex system, and conventional brass dowel pin system. The solid experimental casts were sectioned and then removed from the die system 30 times. Linear distances between all six possible distances were measured from one centre of the transfer coping to the other, using a co-ordinate measuring machine in millimeters up to accuracy of 0.5 microns. Data were tabulated and statistically analyzed by Binomial non parametric test using SPSS version 15. Results: Significant differences were found for distance A-B (P = 0.002, A-C ( P = 0.002, A-D (P value = 0.002, and B-D ( P = 0.021 in Conventional Dowel pin system however for Accu-trac precision die tray system, it was significant only for distance A-D (P = 0.002 but for Pindex system it was non-significant for all the distances measured. Conclusion: Within the limitations of this study, use of Pindex system is recommended when sectioned dies are needed for a multi implant retained prosthesis.

Microstructure characterization and corrosion resistance properties of Pb-Sb alloys for lead acid battery spine produced by different casting methods

Science.gov (United States)

Baig, Muneer; Alam, Mohammad Asif; Alharthi, Nabeel

2018-01-01

The aim of this study is to find out the microstructure, hardness, and corrosion resistance of Pb-5%Sb spine alloy. The alloy has been produced by high pressure die casting (HPDC), medium pressure die casting (AS) and low pressure die casting (GS) methods, respectively. The microstructure was characterized by using optical microscopy and scanning electron microscopy (SEM). The hardness was also reported. The corrosion resistance of the spines in 0.5M H2SO4 solution has been analyzed by measuring the weight loss, impedance spectroscopy and the potentiodynamic polarization techniques. It has been found that the spine produced by HPDC has defect-free fine grain structure resulting improvement in hardness and excellent corrosion resistance. PMID:29668709

Microstructures and mechanical properties of squeeze cast Al–5.0Cu–0.6Mn alloys with different Fe content

International Nuclear Information System (INIS)

Zhang, WeiWen; Lin, Bo; Zhang, DaTong; Li, YuanYuan

2013-01-01

Highlights: • The effect of Fe-rich phases on squeeze cast Al–Cu alloys with high Fe content. • Four kinds of Fe-rich phases may present in Al–Cu alloys. • There is great tolerance to Fe impurities in squeeze cast Al–Cu alloys. - Abstract: The microstructures and mechanical properties of gravity die cast and squeeze cast Al–5.0 wt% Cu–0.6 wt% Mn alloys with different Fe content have been studied using tensile test, optical microscope, scanning electron microscope, electron probe micro-analyzer and image analysis. The results show that four kinds of Fe-rich intermetallics may present in the final microstructures of the alloys: Chinese script α-Fe (Al 15 (FeMn) 3 (CuSi) 2 ) and Al 6 (FeMn), needle-like β-Fe(Al 7 Cu 2 Fe) and Al 3 (FeMn) when the Fe content increases from 0.1 wt% to 1.5 wt%. In the gravity die cast alloy with 0.5 wt% Fe, the Chinese script α-Fe presents as the main Fe-rich intermetallics, and a few needle-like β-Fe also exist. When the Fe content increases to 1.0 wt%, the main Fe-rich intermetallics change to needle-like Al 3 (FeMn) and Chinese-script Al 6 (FeMn). The needle-like β-Fe disappears when the Fe content is 0.5 wt% in the squeeze cast alloy with an applied pressure of 75 MPa. Furthermore, the secondary dendritic arm spacing of α(Al), the percentage of porosity and the volume fraction of the second intermetallics decrease distinctly in the squeeze cast alloy compared to the gravity die cast alloy. There is a peak value of ultimate strength and yield strength for the alloy with 0.5 wt% Fe. The elongations of the alloys decrease gradually with increasing Fe content and the elongation of the squeeze cast alloys is two times more than that of the gravity die cast alloys

Evaluation of Cracking Causes of AlSi5Cu3 Alloy Castings

Directory of Open Access Journals (Sweden)

Eperješi Š.

2014-10-01

Full Text Available Recently, the castings made from aluminum-silicon alloys by pressure die casting are increasingly used in the automotive industry. In practice, on these castings are high demands, mainly demands on quality of their structure, operating life and safety ensuring of their utilization. The AlSi5Cu3 alloy castings are widely used for production of car components. After the prescribed tests, the cracks and low mechanical properties have been identified for several castings of this alloy, which were produced by low pressure casting into a metal mould and subsequent they were heat treated. Therefore, analyses of the castings were realized to determine the causes of these defects. Evaluation of structure of the AlSi5Cu3 alloy and causes of failure were the subjects of investigation presented in this article.

Study on the Surface Microstructure of a Modified STD61 Steel Mold Used for the Die Casting Process

Energy Technology Data Exchange (ETDEWEB)

Yu, Ha-Young; Lee, Seung-Joon; Kang, Minwoo; Lee, Suk-Jin; Lee, Young-Kook [Yonsei University, Seoul (Korea, Republic of); Yang, Won Jon [Korea Institute of Materials Science, Changwon (Korea, Republic of); Jeong, Jae Suk; Kim, Byung-Hoon [Doosan Heavy Industries and Construction, Changwon (Korea, Republic of)

2016-09-15

The surface microstructure and crack formation of an aluminum die-casting mold were investigated. The mold was made of a modified STD61 steel, and was used for more than 165,000 cycles. The mold surface consisted of four layers; an oxidized layer, a decarburized layer, a network carbide layer and a tempered martensite matrix. The depth down to the hardest network carbide layer was ⁓200 μm. Inside the matrix, M{sub 3}C transition carbides were dissolved so that solute C joined pre-existing M{sub 2}3C{sub 6} and MC carbides to make them coarse. About 60% of thermal fatigue cracks had a depth less than 200 μm due to the hard network carbide layer, which obstructed the propagation of cracks. Cracks of over 200 μm were filled with oxide wedges of Al and Si which was which flown from the molten alloy as well as the Fe oxide.

Casting the Spirit: A Handmade Legacy

Science.gov (United States)

Rutenberg, Mona

2008-01-01

This article discusses how an art therapist working in a hospital palliative care unit has incorporated a ritual of hand casting to help bring closure to dying patients and family members who are grieving as death approaches. The finished hand sculptures depict the hands of the patients and, sometimes, of their loved ones. They are faithful and…

14 CFR 23.621 - Casting factors.

Science.gov (United States)

2010-01-01

... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Casting factors. 23.621 Section 23.621... Casting factors. (a) General. The factors, tests, and inspections specified in paragraphs (b) through (d... structural castings except castings that are pressure tested as parts of hydraulic or other fluid systems and...

Technology for producing synthetic cast iron for nuclear power station parts

International Nuclear Information System (INIS)

Blozhko, N.K.; Kurochkin, V.S.; Narkevich, E.A.; Nikitin, L.A.; Petrov, L.A.

1984-01-01

A technology was developed and implemented for producing grades SCh-30 through SCh-40 synthetic cast iron in industrial-frequency induction melting furnaces. Alternative innoculations with ferrosilicon and silicocalcium and alloying with chrome and nickel were studied. The mechanical properties and structure of cast irons produced by various technological methods were studied. The research showed that the sector's plants, equipped with industrial-frequency induction furnaces, can produce high-quality synthetic cast irons containing flake graphite for nuclear-power-station casting, without the use of expensive innoculants. Careful observance of the melting and innoculating technologies makes it possible to produce SCh 40 cast iron, without cementite inclusions, by innoculating with FS 75 ferrosilicon in the amount of 0.7% of the total melt weight. Using an innoculant mixture of 0.2% FS 75 and 0.5% SK 30 and low alloying with nickel and chromium, the cast-iron strength can be increased to 440-450 MPa, although the danger of cementite inclusions increase

Deducing material quality in cast and hot-forged steels by new bending test

Science.gov (United States)

Valberg, Henry; Langøy, Morten; Nedreberg, Mette; Helvig, Torgeir

2017-10-01

A special bend test has been developed and applied for the purpose of characterization and comparison of the material ductility in crankpin steel discs manufactured by casting, or casting subsequently followed by hot open-die forging (ODF) or closed-die forging (CDF). The bending test specimen consists of a small rectangular plate of material with a round hole cut out in the middle. The "eye-shape" specimens were cut out from various positions either near to the surface of, or from the interior of the discs. The test method revealed differences in ductility for the investigated materials, and for different depth positions inside the discs. The roughening of the specimen surface on the top-side of the specimen bend also varied dependent on the processing method for the material. Current results show that this test method is useful for evaluation of material quality in differently processed material. Experimental bend test results are presented for differently processed variants of the same material, i.e., crankpin discs either made by solely casting or casting subsequently followed by hot working either by ODF or CDF.

Hot forging of roll-cast high aluminum content magnesium alloys

Science.gov (United States)

Kishi, Tomohiro; Watari, Hisaki; Suzuki, Mayumi; Haga, Toshio

2017-10-01

This paper reports on hot forging of high aluminum content magnesium alloy sheets manufactured using horizontal twin-roll casting. AZ111 and AZ131 were applied for twin-roll casting, and a hot-forging test was performed to manufacture high-strength magnesium alloy components economically. For twin-roll casting, the casting conditions of a thick sheet for hot forging were investigated. It was found that twin-roll casting of a 10mm-thick magnesium alloy sheet was possible at a roll speed of 2.5m/min. The grain size of the cast strip was 50 to 70µm. In the hot-forging test, blank material was obtained from as-cast strip. A servo press machine with a servo die cushion was used to investigate appropriate forging conditions (e.g., temperature, forging load, and back pressure) for twin-roll casts (TRCs) AZ111 and AZ131. It was determined that high aluminum content magnesium alloy sheets manufactured using twin-roll casting could be forged with a forging load of 150t and a back pressure of 3t at 420 to 430°C. Applying back pressure during hot forging effectively forged a pin-shaped product.

Method for casting thin metal objects

Science.gov (United States)

Pehrson, Brandon P; Moore, Alan F

2015-04-14

Provided herein are various embodiments of systems for casting thin metal plates and sheets. Typical embodiments include layers of mold cavities that are oriented vertically for casting the metal plates. In some embodiments, the mold cavities include a beveled edge such that the plates that are cast have a beveled edge. In some embodiments, the mold cavities are filled with a molten metal through an open horizontal edge of the cavity. In some embodiments, the mold cavities are filled through one or more vertical feed orifices. Further disclosed are methods for forming a thin cast metal plate or sheet where the thickness of the cast part is in a range from 0.005 inches to 0.2 inches, and the surface area of the cast part is in a range from 16 square inches to 144 square inches.

Effect of Heat Treatment on Commercial AlSi12Cu1(Fe) and AlSi12(b) Aluminum Alloy Die Castings

Science.gov (United States)

Battaglia, E.; Bonollo, F.; Ferro, P.; Fabrizi, A.

2018-03-01

High-pressure die castings (HPDCs) cannot normally be heat-treated at a high temperature because of the presence of inner air/gas- or shrinkage-porosity that may lead to the formation of undesired surface blisters. In this paper, an unconventional heat treatment is proposed. Two secondary Al-Si alloys, AlSi12(b) and AlSi12Cu1(Fe), were stabilization heat-treated at 624 K (350 °C) with soaking times ranging from 1 to 8 hours. Enhancement of both static and dynamic mechanical properties was found to be related to the fragmentation of interconnected eutectic Si particles and the smoothing of coarser crystals. Increased ductility after heat treatment was correlated with a decrease in hardness and Si particle roundness. The formation of Si precipitates within the α-Al matrix was also observed.

Direct Cast U-6Nb – 2017 Progress on Cylindrical Castings

Energy Technology Data Exchange (ETDEWEB)

Aikin, Jr., Robert M. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2017-10-04

This report describes work to further develop a sound technical basis and best practices for mold design and process parameters for the Direct Casting of U-6wt%Nb components. One major challenge to the production of U-6Nb components is the propensity for niobium segregation during casting and solidification. This is especially true for cylindrical castings where the vertical side walls allow flotation of Nb resulting in severe inverse macrosegregation. In this work, a small (120 mm diameter by 180 mm tall) and large cylinder (250 mm diameter by 310 mm tall) are examined with a focus on reducing, or eliminating, niobium segregation. It is demonstrated that counter gravity casting (top-to-bottom solidification) can be used to minimize segregation in the small cylinder. Attempts to counter gravity cast the large cylinder were unsuccessful, in large part due to size limitations of the current furnace. A path forward for casting of the large cylinders is discussed.

Numerical modelling of thin-walled hypereutectic ductile cast iron parts

DEFF Research Database (Denmark)

Pedersen, Karl Martin; Hattel, Jesper Henri; Tiedje, Niels Skat

2006-01-01

Solidification of hypereutectic thin-walled ductile cast iron has been modelled in one dimension taking into account the precipitation of off-eutectic austenite dendrites during solidification. The simulations have been compared with casting experiments on plate geometries with plate thicknesses...

Quantification of Feeding Effects of Spot Feeding Ductile Iron Castings made in Vertically Parted Moulds

DEFF Research Database (Denmark)

Vedel-Smith, Nikolaj Kjelgaard; Tiedje, Niels Skat; Sällström, J.

In vertically parted molds it is traditionally difficult to feed heavy sections that cannot be reached by traditional side/top feeders or other conventional methods. This project aims at quantifying the effects of using molded-in ram-up spot feeders as a means of feeding isolated sections in cast...

Application of cast nickel alloys for parts of electronics characterised by special magnetic properties

Directory of Open Access Journals (Sweden)

W. UhI

2008-03-01

Full Text Available Thc thcorctical part of the study highlights thc origin of thc idca 10 start investigations on alloys of high ~nngnctic pcrmcability.manufactured mainly by cornpanics in ~ h Uc S A and Japan.'Phc said materials arc applicd for various pans of ctcctronics uscd by thc military industry. c.g. sntctlitc antcnnas Tor globalcommunication with suhmarincs. and for rcscarch instmrncnts, c,g. fcrromagnctic corcs. Thcy arc chnr:~clcriscd by vcry high lnnpncticpcrrncability. resistivity and corrosion rcsistancc which makc thcm suitablc for opcrat ion undcr cxtrn-~ryingc onditions.Nickel alloys of high magnctic propcrtics arc usuall y manufactured as roZlcd products. The amhition of t hc authors or this srlldy is Inmanufacture !hem as cast prnducts.Thc pmgram of rcscarch incIudcd characteristic of nickcl alloys wirh ddi t i ons of molybdcnum slid iron sn~isryingt hc ahnvc mc~iito ncdrcquircmcnu. with attcn~ionf ocusscd on thcir application for magnctic parts of satcllitc antcnnns and fcrromngnctic corcs.Moulding and casting tcchnologics wcrc proposcd to bcst suit ~ h pcr occss OF maaufacturc of r hcsc clcmcnrs.Thc rangc of chcmicaI cornpostion was sclcctcd 20 cnsurc thc rcquircd magnctic. mcchnnicnl and anti-corrosive pmpcrtics.A scrics of melts was prcparcd and castings of thc abovc mcnlioncd clclncn1s wcrc mndc. Thc chclnicnl composi~ioii of IEIC alloys wasanalyscd along with thc stnlcturc cxarninations nnd quality asscssmcnt rnadc by ~ h cno n-dcsrructi vc rncthods, Casrings wcrc sitbjcctcd tothc finishing trcatmcnt, followed by tests and cxamina~ionsto cnablc thcir practical application.

Stress strain modelling of casting processes in the framework of the control volume method

DEFF Research Database (Denmark)

Hattel, Jesper; Andersen, Søren; Thorborg, Jesper

1998-01-01

Realistic computer simulations of casting processes call for the solution of both thermal, fluid-flow and stress/strain related problems. The multitude of the influencing parameters, and their non-linear, transient and temperature dependent nature, make the calculations complex. Therefore the nee......, the present model is based on the mainly decoupled representation of the thermal, mechanical and microstructural processes. Examples of industrial applications, such as predicting residual deformations in castings and stress levels in die casting dies, are presented...... for fast, flexible, multidimensional numerical methods is obvious. The basis of the deformation and stress/strain calculation is a transient heat transfer analysis including solidification. This paper presents an approach where the stress/strain and the heat transfer analysis uses the same computational...... domain, which is highly convenient. The basis of the method is the control volume finite difference approach on structured meshes. The basic assumptions of the method are shortly reviewed and discussed. As for other methods which aim at application oriented analysis of casting deformations and stresses...

APPLICATION OF POLYSTYRENE FOAM CORE FUSIBLE PATTERNS IN PRODUCTION OF GAS TURBINES’ CAST PARTS

Directory of Open Access Journals (Sweden)

O. I. Shinsky

2016-01-01

Full Text Available The task of replacing the LVM dissolves polystyrene molding on models is at the present time, technologically, economically and environmentally promising from the point of view of industrial applications for gas turbine plants in Ukraine. The authors proposed and tested manufacturing process of casting ceramic molds way to remove the polystyrene model of the dissolution of her organic solvents. Kinetic parameters of the process of dissolving and removing patterns of degradation products the polystyrene in the group of solvents depending on the type and amount of polystyrene were identified. The absence of surface defects of castings, reduction of roughness, increased their accuracy class in comparison to accepted technological regulations of the process of production, which reduced the cost of machined parts and increased utilization of expensive heat-resistant alloys were produced.

Casting Characteristics of High Cerium Content Aluminum Alloys

Energy Technology Data Exchange (ETDEWEB)

Weiss, D; Rios, O R; Sims, Z C; McCall, S K; Ott, R T

2017-09-05

This paper compares the castability of the near eutectic aluminum-cerium alloy system to the aluminum-silicon and aluminum-copper systems. The alloys are compared based on die filling capability, feeding characteristics and tendency to hot tear in both sand cast and permanent mold applications. The castability ranking of the binary Al–Ce systems is as good as the aluminum-silicon system with some deterioration as additional alloying elements are added. In alloy systems that use cerium in combination with common aluminum alloying elements such as silicon, magnesium and/or copper, the casting characteristics are generally better than the aluminum-copper system. In general, production systems for melting, de-gassing and other processing of aluminum-silicon or aluminum-copper alloys can be used without modification for conventional casting of aluminum-cerium alloys.

Morphology transition of the primary silicon particles in a hypereutectic A390 alloy in high pressure die casting.

Science.gov (United States)

Wang, J; Guo, Z; Song, J L; Hu, W X; Li, J C; Xiong, S M

2017-11-03

The microstructure of a high-pressure die-cast hypereutectic A390 alloy, including PSPs, pores, α-Al grains and Cu-rich phases, was characterized using synchrotron X-ray tomography, together with SEM, TEM and EBSD. The Cu-rich phases exhibited a net morphology and distributed at the boundaries of the α-Al grains, which in turn surrounded the PSPs. Statistical analysis of the reconstructed 1000 PSPs showed that both equivalent diameter and shape factor of the PSPs exhibited a unimodal distribution with peaks corresponding to 25 μm and 0.78, respectively.) PSPs morphology with multiple twinning were observed and morphological or growth transition of the PSPs from regular octahedral shape (with a shape factor of 0.85 was mainly caused by the constraint of the Cu-rich phases. In particular, the presence of the Cu-rich phases restricted the growth of the α-Al grains, inducing stress on the internal silicon particles, which caused multiple twinning occurrence with higher growth potential and consequently led to growth transitions of the PSPs.

The Properties of Ammonium Dinitramine (ADN): Part 2: Melt Casting

Science.gov (United States)

Hahma, A.; Edvinsson, H.; Östmark, H.

2010-04-01

A melt casting technique for ammonium dinitramine (ADN) and ADN/aluminum was developed. ADN proved relatively easy to cast, when 1% of magnesium oxide was used as a stabilizer and crystallization kernels. Densities of ADN/MgO 99/1 were 92 to 97% of theoretical mean density (TMD) and those of ADN/Al/MgO 64/35/1 were between 95 and 99% of TMD. Sedimentation of Al in the melt was prevented and the particle wetting was ensured by selecting a suitable particle size for Al. No gelling agents or other additives were used. The casting process and factors influencing it are discussed.

Anodization of cast aluminium alloys produced by different casting methods

Directory of Open Access Journals (Sweden)

K. Labisz

2008-08-01

Full Text Available In this paper the usability of two casting methods, of sand and high pressure cast for the anodization of AlSi12 and AlSi9Cu3 aluminium cast alloys was investigated. With defined anodization parameters like electrolyte composition and temperature, current type and value a anodic alumina surface layer was produced. The quality, size and properties of the anodic layer was investigated after the anodization of the chosen aluminium cast alloys. The Alumina layer was observed used light microscope, also the mechanical properties were measured as well the abrasive wear test was made with using ABR-8251 equipment. The researches included analyze of the influence of chemical composition, geometry and roughness of anodic layer obtained on aluminum casts. Conducted investigations shows the areas of later researches, especially in the direction of the possible, next optimization anodization process of aluminum casting alloys, for example in the range of raising resistance on corrosion to achieve a suitable anodic surface layer on elements for increasing applications in the aggressive environment for example as materials on working building constructions, elements in electronics and construction parts in air and automotive industry.

An eco design strategy for high pressure die casting components: microstructural analysis applied to mass reducing processes; Una estrategia de ecodiseno de piezas obtenidas mediante moldeo a presion: analisis microestructrual aplicado a la desmaterializacion

Energy Technology Data Exchange (ETDEWEB)

Suarez-Pena, B.; Asensio-Lozano, J.

2009-07-01

In this work the study focused on the possibility of use of new aluminium alloys with optimized microstructures that ensure the mechanical properties requested for cast components made by high pressure die casting. The objective was to check the possibility of manufacture of structurally sound eco-steps for escalators with reduced structural integrity. The former arises as a result of a new redesign of the traditional steps aiming at a significant weight reduction. The experimental results show that it is feasible to cut the use of materials during processing and therefore to reduce the impact of the components during its lifetime, whilst the performance and safety standards are kept identical or even improved. (Author) 17 refs.

Modelling the solidification of ductile cast iron parts with varying wall thicknesses

DEFF Research Database (Denmark)

Bjerre, Mathias Karsten; Tiedje, Niels Skat; Thorborg, Jesper

2015-01-01

] with a 2D FE solution of the heat conduction equation is developed in an in-house code and model parameters are calibrated using experimental data from representative castings made of ductile cast iron. The main focus is on the influence of casting thickness and resulting local cooling conditions...

Stainless steel fibre reinforced aluminium matrix composites processed by squeeze casting: relationship between processing conditions and interfacial microstructure

International Nuclear Information System (INIS)

Colin, C.; Marchal, Y.; Boland, F.; Delannay, F.

1993-01-01

This work investigates the influence of some processing parameters on the extent of interfacial reaction in squeeze cast aluminium matrix composites reinforced with 12 μm diameter, continuous stainless steel fibres. The average thickness of the reaction layer at fibre/matrix interfaces was measured by image analysis. When casting was made in a die at room temperature, the thickness of the reaction layer was affected on a distance of several mm from the lateral surface or from the bottom of the preform. The results indicate that the major part of the reaction occurs before solidification of the liquid metal. The control of the extent of interfacial reaction can be achieved through optimization of both infiltration parameters and features of the preform such as the volume fraction of the fibres. (orig.)

Physical modeling and numerical simulation of V-die forging ingot with central void

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

2014-01-01

Numerical simulation and physical modeling performed on small-scale ingots made from pure lead, having a hole drilled through their centerline to mimic porosity, are utilized to characterize the deformation mechanics of a single open die forging compression stage and to identify the influence...... of the lower V-die angle on porosity closure and forging load requirements of large cast ingots. Results show that a lower V-die angle of 120 provides the best closure of centerline porosity without demanding the highest forging loads or developing unreasonably asymmetric shapes that may create difficulties...... in multi-stage open die forging procedures....

Effects of selected casting methods on mechanical behaviour of Al-Mg-Si alloy

Directory of Open Access Journals (Sweden)

Henry Kayode TALABI

2014-11-01

Full Text Available This study investigated the effects of selected casting methods on mechanical behaviour of Al-Mg-Si alloy. The casting methods used was spin, sand and die casting, these were done with a view to determine which of the casting methods will produce the best properties. The pure aluminium scrap, magnesium and silicon were subjected to chemical analysis using spectrometric analyzer, thereafter the charge calculation to determine the amount needed to be charged into the furnace was properly worked out and charged into the crucible furnace from which as-cast aluminium was obtained. The mechanical properties of the casting produced were assessed by hardness and impact toughness test. The optical microscopy and experimental density and porosity were also investigated. From the results it was observed that magnesium and silicon were well dispersed in aluminium matrix of the spin casting. It was observed from visual examination after machining that there were minimal defects. It was also observed that out of the three casting methods, spin casting possesses the best mechanical properties (hardness and impact toughness.

Rheo-Cast Microstructure and Mechanical Properties of AM60 Alloy Produced by Self-Inoculation Rheo-Diecasting Process

Directory of Open Access Journals (Sweden)

Bo Xing

2016-03-01

Full Text Available Rheo-forming is becoming the choice for production of high quality parts with diminished defects and fine integrity. In this paper, the novel self-inoculation rheo-diecasting (SIRD process, in which semisolid slurry is produced by mixing two precursory solid and liquid alloys and subsequently pouring them through a multi-stream fluid director, has been proposed. Microstructural characteristics of AM60 alloy slurry and the microstructure and mechanical properties of rheo-diecasting AM60 samples were investigated. Quenching experiments reveal that the slurry microstructure of AM60 was well refined to irregular α-Mg particles with the average size of approximately 20–40 μm after pouring with the self-inoculation process, and these particles were evolved to globular and coarse morphology while continuously keeping in semisolid state. After rheo-diecasting, the microstructure of the sample was dominated by fine primary α-Mg globules accompanied with tiny secondary α-Mg particles while the sample from conventional liquid die casting was characterized by developed dendrite and porosity. Microscopic analysis indicates that there are three stages of remaining liquid solidification in die cavity in SIRD: α-Mg nucleation and growth on primary α-Mg surface, α-Mg nucleated independently in liquid, and, finally, formation of skeleton devoiced eutectic. Due to diminished porosity and hot tearing, tensile strength and elongation of SIRD samples were increased by 12.9% and 35.3%, respectively, compared to a conventional liquid die casting sample.

Nonaqueous slip casting of high temperature ceramic superconductors using an investment casting technique

Science.gov (United States)

Hooker, Matthew W. (Inventor); Taylor, Theodore D. (Inventor); Wise, Stephanie A. (Inventor); Buckley, John D. (Inventor); Vasquez, Peter (Inventor); Buck, Gregory M. (Inventor); Hicks, Lana P. (Inventor)

1993-01-01

A process for slip casting ceramic articles that does not employ parting agents and affords the casting of complete, detailed, precision articles that do not possess parting lines is presented. This process is especially useful for high temperature superconductors and water-sensitive ceramics. A wax pattern for a shell mold is provided, and an aqueous mixture of a calcium sulfate-bonded investment material is applied as a coating to the wax pattern. The coated wax pattern is then dried, followed by curing to vaporize the wax pattern and leave a shell mold of the calcium sulfate-bonded investment material. The shell mold is cooled to room temperature, and a ceramic slip, created by dispersing a ceramic powder in an organic liquid, is poured therein. After a ceramic shell of desired thickness or a solid article has set up in the shell mold, excess ceramic slip is poured out. The shell mold is misted with water and peeled away from the ceramic article, after which the ceramic is fired to provide a complete, detailed, precision, high temperature superconductive ceramic article without parting lines. The casting technique may take place in the presence of a magnetic field to orient the ceramic powders during the casting process.

On the microstructural factors affecting creep resistance of die-cast Mg–La-rare earth (Nd, Y or Gd) alloys

Energy Technology Data Exchange (ETDEWEB)

Gavras, S. [Magnesium Innovation Centre, Helmholtz-Zentrum Geesthacht, Max-Planck-Straße 1, Geesthacht (Germany); Zhu, S.M. [School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Nie, J.F. [Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); Gibson, M.A. [School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Carlton, Victoria 3053 (Australia); Department of Materials Science and Engineering, Monash University, Victoria 3800 (Australia); CSIRO Manufacturing, Clayton, Victoria 3168 (Australia); Easton, M.A. [School of Aerospace, Mechanical and Manufacturing Engineering, RMIT University, Carlton, Victoria 3053 (Australia)

2016-10-15

Creep properties of high-pressure die-cast Mg–La-RE (Nd, Y or Gd) alloys, varying in ternary RE additions and in different heat treatment conditions, have been investigated. Through the use of short-term solution treatments (1 h at 520 °C) it was shown that the continuous intermetallic phase present in the eutectic at grain boundaries became discontinuous. This effect, in combination with the likely removal of the localised region of supersaturated solute in solid solution near grain boundaries, reduced the creep resistance. When relatively high concentrations of ternary alloying additions were used, solid solution strengthening and precipitation hardening appeared to compensate for the negative effect of reduced grain boundary reinforcement. Microstructural investigation revealed that Nd-containing alloys had fewer and larger dynamic precipitates present in the α-Mg matrix following creep testing at 177 °C and 90 MPa. It was concluded that grain boundary reinforcement in combination with the thermal stability of the precipitates formed, which is ultimately related to the diffusivity of solute in solid solution, are also contributing factors to creep resistance.

Casting fine grained, fully dense, strong inorganic materials

Science.gov (United States)

Brown, Sam W.; Spencer, Larry S.; Phillips, Michael R.

2015-11-24

Methods and apparatuses for casting inorganic materials are provided. The inorganic materials include metals, metal alloys, metal hydrides and other materials. Thermal control zones may be established to control the propagation of a freeze front through the casting. Agitation from a mechanical blade or ultrasonic energy may be used to reduce porosity and shrinkage in the casting. After solidification of the casting, the casting apparatus may be used to anneal the cast part.

AN INTRODUCTION TO RAPID CASTING: DEVELOPMENT AND INVESTIGATION OF PROCESS CHAINS FOR SAND CASTING OF FUNCTIONAL PROTOTYPES

Directory of Open Access Journals (Sweden)

D. Dimitrov

2012-01-01

Full Text Available

ENGLISH ABSTRACT: This paper discusses the results obtained from studies on different Rapid Tooling process chains in order to improve the design and manufacture of foundry equipment that is used for sand casting of prototypes in final material. These prototypes are intended for functional and pre-production tests of vehicles. The Three Dimensional Printing process is used as core technology. Subsequently, while considering aspects such as time, cost, quality (accuracy and surface roughness, and tool life, a framework is presented for the evaluation and selection of the most suitable process chain in accordance with specific requirements. This research builds on an in-depth characterisation of the accuracy and repeatability of a 3D printing process.

AFRIKAANSE OPSOMMING: Hierdie artikel bespreek die resultate wat verkry is tydens studies op verskillende Snel-Gereedskapvervaardigingproseskettings wat ondersoek is teneinde die ontwerp en vervaardiging van sandgietgereedskap, om prototipes in finale materiaal te vervaardig, te verbeter. Die prototipes is bestem vir gebruik in funksionele- en voorproduksietoetse van voertuie. Die sogenaamde Driedimensionele Drukproses (3DP is as kerntegnologie aangewend. Gevolglik, na oorweging van aspekte soos tyd, koste, kwaliteit (akkuraatheid en oppervlakafwerking, en gereedskapleeftyd, is ’n raamwerk ontwikkel vir die evaluering en seleksie van die mees geskikte prosesketting met inagname van spesifieke vereistes. Hierdie navorsing bou op ’n diepgaande karakterisering van die akkuraatheids- en herhaalbaarheidsvermoë van ’n 3D drukproses.

Microstructure and Wear Properties of Electron Beam Melted Ti-6Al-4V Parts: A Comparison Study against As-Cast Form

Directory of Open Access Journals (Sweden)

Wei Quan Toh

2016-11-01

Full Text Available Ti-6Al-4V (Ti64 parts of varying thicknesses were additively manufactured (AM by the powder-bed-based electron beam melting (EBM technique. Microstructure and wear properties of these EBM-built Ti-6Al-4V parts have been investigated in comparison with conventionally cast Ti64 samples. Sliding wear tests were conducted using a ball-on-disc micro-tribometer under ambient conditions. Experimental results reveal that EBM-built Ti64 samples exhibited higher microhardness and an overall larger coefficient of friction as compared to the as-cast counterpart. Of interest is that the corresponding specific wear volumes were lower for EBM-built Ti64 samples, while the as-cast Ti64 showed the poorest wear resistance despite its lower coefficient of friction. Wear mechanisms were provided in terms of quantitative microstructural characterization and detailed analysis on coefficient of friction (COF curves.

Method and mold for casting thin metal objects

Science.gov (United States)

Pehrson, Brandon P; Moore, Alan F

2014-04-29

Provided herein are various embodiments of systems for casting thin metal plates and sheets. Typical embodiments include layers of mold cavities that are oriented vertically for casting the metal plates. In some embodiments, the mold cavities include a beveled edge such that the plates that are cast have a beveled edge. In some embodiments, the mold cavities are filled with a molten metal through an open horizontal edge of the cavity. In some embodiments, the mold cavities are filled through one or more vertical feed orifices. Further disclosed are methods for forming a thin cast metal plate or sheet where the thickness of the cast part is in a range from 0.005 inches to 0.2 inches, and the surface area of the cast part is in a range from 16 square inches to 144 square inches.

Numerical simulation of complex multi-phase fluid of casting process and its applications

Directory of Open Access Journals (Sweden)

CHEN Li-liang

2006-05-01

Full Text Available The fluid of casting process is a typical kind of multi-phase flow. Actually, many casting phenomena have close relationship with the multi-phase flow, such as molten metal filling process, air entrapment, slag movement, venting process of die casting, gas escaping of lost foam casting and so on. Obviously, in order to analyze these phenomena accurately, numerical simulation of the multi-phase fluid is necessary. Unfortunately, so far, most of the commercial casting simulation systems do not have the ability of multi-phase flow modeling due to the difficulty in the multi-phase flow calculation. In the paper, Finite Different Method (FDM technique was adopt to solve the multi-phase fluid model. And a simple object of the muiti-phase fluid was analyzed to obtain the fluid rates of the liquid phase and the entrapped air phase.

Metodes in die Christelike etiek

African Journals Online (AJOL)

The basic question in Christian ethics is not primarily. 'What should I do?' The basic question is rather ' ... should therefore be accepted as being part of the method used in Christian ethics. 1. INLEIDEND ..... aan die kant van die onderdrukte' verkondig word, word die Christen opgeroep om horn te skaar aan die kant van die ...

Defecation of a colon cast as a rare presentation of acute graft-versus-host disease

International Nuclear Information System (INIS)

Al Ashgar, Hamad; Peedikayil, Musthafa; Chaudhri, Naeem; AlGhamdi, Abdulmonem

2009-01-01

Diffuse involvement of the gastrointestinal tract by graft versus host disease (GVHD) is a common complication of allogeneic hematopoietic stem cell transplant (HSCT). Gastrointestinal GVHD usually presents 3 or more weeks after HSCT and is characterized by profuse diarrhea, anorexia, nausea, vomiting, abdominal pain and gastrointestinal bleeding. We report a case of a 23 year old male who had undergone allogeneic HSCT and presented with bloody diarrhea on the 90th day post-HSCT. On the fourth day of admission, the patient passed per rectum a 27-cm long pinkish colored fleshy material recognized as a colon cast. Sigmoidoscopy showed a congested and erythematous rectum with the remaining portion of the colon cast attached to the proximal part of the sigmoid colon. A biopsy from the rectal wall was suggestive of grade 4 GVHD. The patient was treated with methylprednisolone, cyclosporine and mycophenolate mofetil, with a partial response (diarrhea and abdominal pain improved), but then he developed multiple other medical complications and died after 3 months. (author)

Results obtained so far with the production of turbine and valve casings made of the new 9% Cr cast steel types G-X 12 CrMoWVNbN 10 11 and G-X 12 CrMoVNbN 91; Erfahrungsbericht ueber die Herstellung von Turbinen- und Ventilgehaeusen aus den neuen 9% Cr-Stahlgusssorten G-X 12 CrMoWVNbN 10 1 1 und G-X 12 CrMoVNbN 91

Energy Technology Data Exchange (ETDEWEB)

Schuster, F.; Buberl, A.; Hanus, R. [VOEST-ALPINE STAHL LINZ GmbH, Linz (Austria); Cerjak, H. [Technische Univ., Graz (Austria)

1996-12-31

In the course of production start-up of new 9-10% Cr cast steel types, and application of R and D results to practice, the following examinations and modifications have been performed: 1. Reduction of average chromium content from 10.5 to 9.5% in order to suppress delta ferrite segregation, and adjustment of austenite and ferrite stabilizing alloying constituents. 2. Analysis of typical defects in castings, and modification of casting and feeding techniques in compliance with the saturation behaviour of the new 9-10% Cr steels. These measures achieved a reduction of feeding-based flaws (shrinkage) in the last few cast pieces. 3. The good weldability was proven of the new 9-10% Cr steels by means of welding tests and crack-free production and construction welds made in cast pieces. (orig./MM) [Deutsch] Im Zuge der Produktionsaufnahme neuer 9-10% Cr-Stahlgusssorten und der Ueberleitung der F and E Ergebnisse in die betriebliche Praxis wurden folgende Untersuchungen und Anpassungen vorgenommen: 1. Um die Deltaferritausscheidung zu unterdruecken, wurde der mittlere Chromgehalt von 10,5 auf 9,5% abgesenkt und die austenit- und ferritstabilisierenden Legierungselemente besser angepasst. 2. Die Analyse typischer Fehlererscheinungen an Gussstuecken machten eine Anpassung der Giess- und Speisungstechnik an das Saettigungsverhalten der neuen 9-10% Cr-Staehle erforderlich. Diese Massnahmen fuehrten zu einer Verringerung der Speisungsfehler (Lunker) bei den zuletzt abgegossenen Gussstuecken. 3. Bei Schweissversuchen und an Gussstuecken rissfrei ausgefuehrten Fertigungs- und Konstruktionsschweissungen konnte die gute Schweisseignung der neuen 9-10% Cr-Staehle nachgewiesen werden. (orig./MM)

Effect of Contact Time on Interface Reaction between Aluminum Silicon (7% and 11% Alloy and Steel Dies SKD 61

Directory of Open Access Journals (Sweden)

Bambang Suharno

2010-10-01

Full Text Available Die soldering (die sticking is a defect of metal casting in which molten metal “welds” to the metallic die mold surface during casting process. Die soldering is the result of an interface reaction between the molten aluminum and the die material. Aluminum alloy with 7 and 11% silicon and SKD 61 die steel are the most common melt and die material used in aluminum die casting. This research is done to study the morphology and the characteristics of the formed AlxFeySiz intermetallic layer during interface reaction at dipping test. The samples of as-anneal SKD 61 tool steel was dipped into the molten of Al-7%Si held at temperature 680oC and into molten Al-11%Si held at temperature 710oC with the different contact time of 10 minutes; 30 minutes; and 50 minutes. The research results showed that the interface reaction can form a compact intermetallic layer with AlxFey phase and a broken intermetallic layer with AlxFeySiz phase on the surface of SKD 61 tool steel. The increasing of the contact time by the immersion of material SKD 61 tool steel in both of molten Al-7%Si and Al-11%Si will increase the thickness of the AlxFeySiz intermetallic layer until an optimum point and then decreasing. The micro hardness of the AlxFeySiz intermetallic layer depends on the content of the iron. Increasing of the iron content in intermetallic layer will increase the micro hardness of the AlxFeySiz. This condition happened because the increasing of Fe content will cause forming of intermetallic AlxFeySiz phase becomes quicker.

Current status and manufacturing technologies of magnesium alloy parts in Japanese home electronics

Energy Technology Data Exchange (ETDEWEB)

Nishikawa, Y.; Takara, A. [Corporate Production Engineering Div., Matsushita Electric Industrial Co., Ltd., Osaka (Japan)

2003-07-01

The Japanese home electronics market has demanded that the newer products must be smaller, thinner and lighter. The use of magnesium alloys for Japanese home electronics has increased since the latter half of the 1990's. Magnesium alloys have been used mainly for the outer cases of portable electric products, because of their lightness and rigidness. Magnesium is also a promising material from the viewpoint of recycling. Magnesium alloy parts have been mass-produced for the outer cases of portable home electronics, such as, mini-disc player, notebook type personal computer or cell phone. The parts have the characteristics of high quality in appearance and thin walled, complicated shape with rib or boss. Most of them are formed by die-casting or injection molding technologies. After casting, the parts are treated precise machining to clear minute surface cracks or voids. Subsequently, they are operated anti-corrosion treatment and spray coating. Recycling have already carried out for magnesium alloy scraps to be cast again. Paint stripping before remelting is performed by alkali solutions or sandblast techniques for coated scraps. Finally, the development of promising press forming technologies is also introduced. (orig.)

Optimization of Squeeze Casting Parameters for 2017 A Wrought Al Alloy Using Taguchi Method

Directory of Open Access Journals (Sweden)

Najib Souissi

2014-04-01

Full Text Available This study applies the Taguchi method to investigate the relationship between the ultimate tensile strength, hardness and process variables in a squeeze casting 2017 A wrought aluminium alloy. The effects of various casting parameters including squeeze pressure, melt temperature and die temperature were studied. Therefore, the objectives of the Taguchi method for the squeeze casting process are to establish the optimal combination of process parameters and to reduce the variation in quality between only a few experiments. The experimental results show that the squeeze pressure significantly affects the microstructure and the mechanical properties of 2017 A Al alloy.

Design optimization of clutch housing mold by fluid flow and solidification simulation

Energy Technology Data Exchange (ETDEWEB)

Hosseini, Seyedeh Maryam; Utlu, Zafer [Istanbul Aydin Univ., Istanbul (Turkmenistan)

2016-06-15

Aluminum die casting is so complex where flow momentum is critical matter in the mould filling process due the high velocity of the liquid metal. Actually, in complex parts the exact calculation of mould filling performance with using experimental knowledge is almost impossible. Aluminum die castings play a definitive role in the manufacturing of lightweight automobile bodies. Hence it is more essential today that these castings be produced with the high quality methods. In this condition the simulation is becoming more important in the designing procedure. This saves time and reduces the cost of the casting system design, which is an advantage of using simulation programs. Also, economical utilization of materials can be obtained when the quantity of test castings is decreased. This paper describes the advantages of the clutch housing die casting mold simulations to achieve better casting system design in High pressure die castings (HPDC). Filling analysis is used to determine the size and location of the gate as well as proper runner system design for ensuring a complete and balanced filling of the clutch housing part.

Synergistic effects of composition and heat treatment on microstructure and properties of vacuum die cast Al-Si-Mg-Mn alloys

Directory of Open Access Journals (Sweden)

Jun-jie Xu

2018-03-01

Full Text Available The purpose of this study was to prepare high-quality Al-Si-Mg-Mn alloy with a good combination of strength and ductility employing the vacuum-assisted high-pressure die cast process. An orthogonal study of heat treatments was conducted to design an optimized T6 heat treatment process for both Al-10%Si-0.3%Mg-Mn and Al-11%Si-0.6%Mg-Mn alloys. The results demonstrate that no obvious blisters and warpage were observed in these two alloys with solid solution treatment. After the optimal T6 heat treatment of 530°C×3h + 165°C×6h, Al-11%Si-0.6%Mg-Mn alloy has better mechanical properties, of which tensile strength, yield strength and elongation reached 377.3 MPa, 307.8 MPa and 9%, respectively. The improvement of mechanical properties can be attributed to the high density of needle-like β″(Mg5Si6 precipitation after aging treatment and the fine and spherical eutectic Si particles uniformly distributed in the α-Al matrix.

PRODUCTION OF ROTARY ENGINES’ PARTS FROM ALUMINUM ALLOYS USING LOST FOAM CASTING PROCESS

Directory of Open Access Journals (Sweden)

E. I. Marukovich

2018-01-01

Full Text Available The production technology of casting details for rotary engine from the aluminum alloy АК12М2 is developed. The bulk density of expanded polystyrene to ensure the best quality of the surface of castings has been experimentally established. The lost foam casting shop was organized in the experimental department of the Institute.

Modelling and multi objective optimization of LM13 aluminium alloy squeeze cast process parameters using taguchi and genetic algorithm

Directory of Open Access Journals (Sweden)

S. Vellingiri

2018-01-01

Full Text Available This present investigation deals with squeeze casting process in order to produce a component with good mechanical properties such as micro-hardness(VH, tensile strength(Rm, and density(ρ on LM13 by varying squeeze pressure(P, molten temperature(Tm and die temperature(Td. Taguchi experimental design L9 orthogonal array was used to determine the signal to noise ratio. The results specified that the squeeze pressure and die preheat temperature are the most influencing parameters for mechanical properties improvement. Genetic algorithm (GA has been applied to optimize the casting parameters that simultaneously maximize the responses.

Effects of preparation relief and flow channels on seating full coverage castings during cementation.

Science.gov (United States)

Webb, E L; Murray, H V; Holland, G A; Taylor, D F

1983-06-01

Machined steel dies were used to study the effects of three die modifications on seating full coverage castings during cementation. The die modifications consisted of occlusal channels, occlusal surface relief, and axial channels. Fourteen specimens having one or more forms of die modification were compared with two control specimens having no die modifications. Statistical analysis of the data revealed that the addition of four axial channels to the simulated preparation on the steel die produced a significant reduction in the mean marginal discrepancy during cementation. Occlusal modifications alone failed to produce significant reductions in marginal discrepancies when compared with the control specimens. Occlusal modifications in conjunction with axial channels failed to produce further significant reductions in marginal discrepancies when compared with those reductions observed in specimens having only axial channels.

Die funksie van die belydenis in die struktuur van die kerk en die ...

African Journals Online (AJOL)

Ter wille van die argument wat in hierdie voordrag na vore gebring word, word vier sodanige konstituerende elemente van die kerklike struktuur onderskei, te wete die belydenis, die teologie, die verkondi- ging (meer bepaald die prediking) en die kerkorde (kerkwet volgens ons terminologie). Ons gaan nou elkeen hiervan ...

die rol van die unieverdedigingsmag in die onderdrukking van die

African Journals Online (AJOL)

agv regeringsoptrede nie.39. Siotsom. In die geskiedenis van die Unieverdedigings- mag word die gebeure random die 1914-staking oorskadu deur die Rebellie en Suid-Afrika se deelname aan die Eerste Wereldoorlog. Tog was dit 'n belangrike mylpaal in die geskiedenis van die organisasie, omdat dit sy eerste optrede ...

Vacuum Die Casting Process and Simulation for Manufacturing 0.8 mm-Thick Aluminum Plate with Four Maze Shapes

Directory of Open Access Journals (Sweden)

Chul Kyu Jin

2015-02-01

Full Text Available Using vacuum die casting, 0.8 mm-thick plates in complicated shapes are manufactured with the highly castable aluminum alloy Silafont-36 (AlSi9MgMn. The sizes and shapes of the cavities, made of thin plates, feature four different mazes. To investigate formability and mechanical properties by shot condition, a total of six parameters (melt temperatures of 730 °C and 710 °C; plunger speeds of 3.0 m/s and 2.5 m/s; vacuum pressure of 250 mbar and no vacuum are varied in experiments, and corresponding simulations are performed. Simulation results obtained through MAGMA software show similar tendencies to those of the experiments. When the melt pouring temperature is set to 730 °C rather than 710 °C, formability and mechanical properties are superior, and when the plunger speed is set to 3.0 m/s rather than to 2.5 m/s, a fine, even structure is obtained with better mechanical properties. The non-vacuumed sample is half unfilled. The tensile strength and elongation of the sample fabricated under a melt temperature of 730 °C, plunger speed of 3.0 m/s, and vacuum pressure of 250 mbar are 265 MPa and 8.5%, respectively.

Comparative Evaluation of Conventional and Accelerated Castings on Marginal Fit and Surface Roughness

Science.gov (United States)

Jadhav, Vivek Dattatray; Motwani, Bhagwan K.; Shinde, Jitendra; Adhapure, Prasad

2017-01-01

Aims: The aim of this study was to evaluate the marginal fit and surface roughness of complete cast crowns made by a conventional and an accelerated casting technique. Settings and Design: This study was divided into three parts. In Part I, the marginal fit of full metal crowns made by both casting techniques in the vertical direction was checked, in Part II, the fit of sectional metal crowns in the horizontal direction made by both casting techniques was checked, and in Part III, the surface roughness of disc-shaped metal plate specimens made by both casting techniques was checked. Materials and Methods: A conventional technique was compared with an accelerated technique. In Part I of the study, the marginal fit of the full metal crowns as well as in Part II, the horizontal fit of sectional metal crowns made by both casting techniques was determined, and in Part III, the surface roughness of castings made with the same techniques was compared. Statistical Analysis Used: The results of the t-test and independent sample test do not indicate statistically significant differences in the marginal discrepancy detected between the two casting techniques. Results: For the marginal discrepancy and surface roughness, crowns fabricated with the accelerated technique were significantly different from those fabricated with the conventional technique. Conclusions: Accelerated casting technique showed quite satisfactory results, but the conventional technique was superior in terms of marginal fit and surface roughness. PMID:29042726

Temperature measurement during solidification of thin wall ductile cast iron. Part 2: Numerical simulations

DEFF Research Database (Denmark)

Pedersen, Karl Martin; Tiedje, Niels Skat

2008-01-01

Temperature measurements in castings are carried out with thermocouples (TC’s), which are inserted in the melt. The TC influence solidification of the casting, especially in thin wall castings where the heat content of the melt is small compared to the cooling power of the TC. A numerical analysi...

Temperature and microstructure characteristics of silumin casting AlSi9 made with investment casting method

Directory of Open Access Journals (Sweden)

S. Pietrowski

2011-07-01

Full Text Available This work presents the research result of the temperature distribution and the microstructure in certain parts of the field-glass body frame casting made from silumin AlSi9 using the investment casting method in the ceramic mould. It was proved that the highest temperature of the silumin appears in the sprue in which the silumin is in the liquid-solid state, though the process of silumin crystallization in the casting is finished. It was stated that in certain elements of the casting the side opposite to the runner crystallizes and cools fastest. The differences in the rate of crystalline growth and cooling of certain casting elements cause differ- ent microstructure in them which can also influence the mechanic properties.It is necessary to state that the temperature of the initial heating of the ceramic mold equal to 60oC guarantees obtaining of the castings without defects and of little porosity. Incomplete modification of the silumin with strontium causes silica precipitation to appear close to the spherical ones.

Simulation of thermal radiation, illustrated by the Bridgman casting process for directional solidification of turbine blades; Simulation von Waermestrahlung am Beispiel des Bridgman-Verfahrens zur gerichteten Erstarrung von Turbinenschaufeln

Energy Technology Data Exchange (ETDEWEB)

Hofmann, N

1996-12-31

Directionally solidified turbine blades for high-temperature applications today are commonly produced by the Bridgman casting process. The production of a newly constructed turbine blade requires a number of costly and time-consuming casting experiments. The author develops a numerical simulation model based on the finite element method and net radiation method for low-cost and short-term simulation and optimisation of the casting experiments. Several different numerical methods for calculating thermal radiation are compared (radiosity, ray tracing and the finite difference method), and the simulation results are presented for several exemplry turbine blades. Further, an optimisation strategy for improving the quality of the turbine blade casting process is presented. (orig.). 65 figs., 8 tabs. [Deutsch] Gerichtet erstarrte Turbinenschaufeln mit hoher Einsatztemperatur werden nach dem heutigen Stand der Technik nach dem Bridgman-Verfahren gegossen. Die Herstellung einer neu konstruierten Turbinenschaufel verlangt eine Reihe von kosten- und zeitaufwendigen Giessexperimenten. In der vorliegenden Arbeit wird ein numerisches Simulationsmodell auf Basis der Finiten Elemente Methode und Net Radiation Methode entwickelt, mit dem sich kostenguenstig und in kurzen Zeitraeumen die Giessversuche simulieren und optimieren lassen. Die Arbeit vergleicht verschiedene numerische Loesungsverfahren fuer die Waermestrahlung (Radiosity, Ray Tracing und Finite Differenzen Verfahren) und stellt am Beispiel einiger Turbinenschaufeln die Simulationsergebnisse dar. Weiterhin wird eine Optimierungsstrategie fuer Verbesserung der Gussqualitaet von Turbinenschaufeln vorgestellt. (orig.)

Spatial Bimetallic Castings Manufactured from Iron Alloys

Directory of Open Access Journals (Sweden)

M. Cholewa

2007-07-01

Full Text Available In this paper a conception for manufacturing method of skeleton castings with composite features was shown. Main application of such castings are the working organs of machines subjected to intensive abrasive and erosive wear. Skeleton geometry was based on three-dimensional cubic net consisting of circular connectors and nodes joining 6 connectors according to Cartesian co-ordinate system. Dimension of an elementary cell was equal to 10 mm and diameter of single connector was equal to 5 mm. For bimetallic castings preparation two Fe based alloys were used: L25SHMN cast steel for skeleton substrate and ZlCr15NiMo cast iron for working part of the casting. In presented work obtained structure was analyzed with indication of characteristic regions. Authors described phenomena occurring at the alloys interface and phases in transition zone. A thesis was formulated concerning localization of transition zone at the cast iron matrix – cast steel reinforcement interface. Direction of further studies were indicated.

Fundamentals of Numerical Modelling of Casting Processes

DEFF Research Database (Denmark)

Hattel, Jesper Henri; Pryds, Nini; Thorborg, Jesper

Fundamentals of Numerical Modelling of Casting Processes comprises a thorough presentation of the basic phenomena that need to be addressed in numerical simulation of casting processes. The main philosophy of the book is to present the topics in view of their physical meaning, whenever possible......, rather than relying strictly on mathematical formalism. The book, aimed both at the researcher and the practicing engineer, as well as the student, is naturally divided into four parts. Part I (Chapters 1-3) introduces the fundamentals of modelling in a 1-dimensional framework. Part II (Chapter 4...

Die rol van die blanke werker in die motivering van die swart werker

Directory of Open Access Journals (Sweden)

G. J. Oosthuizen

1980-11-01

Opsomming Die motivering van die Swart werker kan nie in die huidige situasie in isolasie bestudeer word nie, omdat die Blanke werker steeds in die bestuursposisie is en daarom die motivering van die Swart werker kan beïnvloed. Hierdie ondersoek was daarop gerig om die rol van die Blanke werker in die motivering van die Swart werker nader te ondersoek. Die houding en die leierskapsbenadering van die Blanke werker teenoor die Swart werker is gemeet, asook die behoeftes wat volgens die Blanke werker by die Swart werker bestaan, bevredig is, of nie bestaan nie. Die behoeftes van Swart werkers, soos deur hulleself gesien, is ook ondersoek. Ten opsigte van sekere aspekte is beduidende verskille gevind.

Investment casting: parameters, application and recent development

International Nuclear Information System (INIS)

Zaid, A.I.O.

2007-01-01

Investment casting process, also referred to as the lost wax method and as precision casting, has been known for more than 6000 years. However, industry paid little attention to the process until the urgent military demands of World War 1 overtaxed the machine tool industry and short cuts were then needed to provide finished tools and precision parts, avoiding time-consuming in machining and assembly. The use of the process for the production of commercial casting has grown in the second half of the 20th century. The process is highly flexible and can handle great variety of parts which are difficult or even not possible to be produced by forging or other casting methods. In this paper, the investment casting process, its applications, advantages and limitations together with the parameters affecting it as related to pattern material, cluster, slurry and molten metal are given and discussed. Furthermore, the recent developments in the process particularly in manufacturing parts made of superalloys e.g nickel-base alloys are given and discussed. The striking fact that the process has advanced further in the last 60 years than it has in the previous 6000 years ensures that in the coming years of this century development in the process and its application will continue to advance in the interest of achieving higher quality and precision which can meet the critical performance standards being imposed. (author)

Die singulation method

Science.gov (United States)

Swiler, Thomas P.; Garcia, Ernest J.; Francis, Kathryn M.

2013-06-11

A method is disclosed for singulating die from a semiconductor substrate (e.g. a semiconductor-on-insulator substrate or a bulk silicon substrate) containing an oxide layer (e.g. silicon dioxide or a silicate glass) and one or more semiconductor layers (e.g. monocrystalline or polycrystalline silicon) located above the oxide layer. The method etches trenches through the substrate and through each semiconductor layer about the die being singulated, with the trenches being offset from each other around at least a part of the die so that the oxide layer between the trenches holds the substrate and die together. The trenches can be anisotropically etched using a Deep Reactive Ion Etching (DRIE) process. After the trenches are etched, the oxide layer between the trenches can be etched away with an HF etchant to singulate the die. A release fixture can be located near one side of the substrate to receive the singulated die.

Die skrifbeskouing van feministiese teoloë, in die besonder dié van Fiorenza, Brenner en Van Dijk-Hemmes – beoordeel in die lig van die gereformeerde teologie

Directory of Open Access Journals (Sweden)

Alta E. Swart

2013-10-01

Full Text Available Dit wil voorkom asof die feministiese Skrifbeskouing op die beginsel van selektiewe Skrifgesag berus. Dit beteken dat slegs dié dele in die Bybel wat met die feministiese ideologie ooreenstem, as gesaghebbend aanvaar word. Dit is veral die sogenaamde androsentriese taalgebruik wat dit vir aanhangers van hierdie benadering moeilik maak om die hele Skrif as gesaghebbend te erken. Hermeneuties vertoon hierdie benadering groot ooreenkomste met die Postmodernisme, waarin geen vaste reëls bestaan om die betekenis van tekste te bepaal nie. Gesien in die lig van die gereformeerde teologie, soos veranker in die Woord en belydenisskrifte, vertoon die feministiese teologie ernstige leemtes. Die bydraes (Skrifbeskouing van drie prominente feministiese teoloë – Fiorenza, Brenner en Van Dijk-Hemmes – word onder die loep geneem en teologies-krities geëvalueer ten einde hierdie leemtes uit te wys. It appears that the feminist view of Scripture is based on the principle of selective authority of the Scriptures, which means that only the parts of the Bible corresponding with the feminist ideology are accepted as authoritative. The use of androcentric language, in particular, makes it difficult for followers of feminism to accept the whole Bible as authoritative. Hermeneutically, their approach resembles Postmodernism, interpreting without any rules. Viewed from the paradigm of the reformed theology, which is anchored in Scripture and the articles of faith, feminist theology shows serious shortfalls. The contributions of three prominent feminist theologians – Fiorenza, Brenner and Van Dijk-Hemmes – are studied closely and evaluated critically in the light of the reformed theology, to underline these shortfalls.

EXPERIMENTAL STUDY OF THE DYNAMICS OF CENTRIFUGAL CASTING MACHINES FOR PRODUCTION OF MILL ROLLS

Directory of Open Access Journals (Sweden)

P. G. Anofriev

2017-06-01

Full Text Available Purpose. The main purpose of experimental studies is to establish the adequacy of the developed mathematical models of machine fluctuations and the actual parameters of machine vibration. Almost all casting machines for the production of mill rolls have a unique design and performances. The additional aim of this work is to compare the vibration level of the casting machine with the requirements of the current vibration standards for new technological machines. Frequency analysis of the oscillations allows establishing defects in workmanship, errors of rotating parts installation and their influence on the dynamics of the machine. Methodology. Measurement of vibration parameters was performed on the moving parts of roller bearings of the machine. To measure the amplitudes of accelerations in three mutually perpendicular directions piezoelectric sensors with magnetic mount were used. Electrical signals from the sensors were recorded on magnetic tape. Further analysis of the oscillations was carried out and visualized using specialized frequency analyzer. The frequency analyzer implements the algorithm of fast Fourier transformation and/or integration of sensor input signal. After the first integration the data for plotting the vibration velocity spectrogram were obtained and as a result of the second integration there are the data of vibration displacements spectrogram of the machine supports. Findings. The results of experimental studies of centrifugal casting machine vibrations for the production of two-layer rolls were presented. There were obtained and analyzed the spectrograms of accelerations, velocities and displacements of moving parts of the upper and lower roller supports. The work of the machine is associated with the calculated values passing of critical frequencies and the short-term development of resonance oscillations of the rotor and roller bearings. Originality. For the first time the author obtained the frequency spectra of

[Comparative adaptation of crowns of selective laser melting and wax-lost-casting method].

Science.gov (United States)

Li, Guo-qiang; Shen, Qing-yi; Gao, Jian-hua; Wu, Xue-ying; Chen, Li; Dai, Wen-an

2012-07-01

To investigate the marginal adaptation of crowns fabricated by selective laser melting (SLM) and wax-lost-casting method, so as to provide an experimental basis for clinic. Co-Cr alloy full crown were fabricated by SLM and wax-lost-casting for 24 samples in each group. All crowns were cemented with zinc phosphate cement and cut along longitudinal axis by line cutting machine. The gap between crown tissue surface and die was measured by 6-point measuring method with scanning electron microscope (SEM). The marginal adaptation of crowns fabricated by SLM and wax-lost-casting were compared statistically. The gap between SLM crowns were (36.51 ± 2.94), (49.36 ± 3.31), (56.48 ± 3.35), (42.20 ± 3.60) µm, and wax-lost-casting crowns were (68.86 ± 5.41), (58.86 ± 6.10), (70.62 ± 5.79), (69.90 ± 6.00) µm. There were significant difference between two groups (P casting method and SLM method provide acceptable marginal adaptation in clinic, and the marginal adaptation of SLM is better than that of wax-lost-casting method.

Die Frage nach Gerechtigkeit.

Directory of Open Access Journals (Sweden)

Martin Jäggle

2014-07-01

Full Text Available ENGLISH: In the first part six stages in the author’s path of life are described, which have influenced his engagement with justice. The second part gives an insight into his religious educational work, in which the issue of justice was especially significant on the example of ‘religion in the context of migration’ and of the ecumenic initiative ‘lebens.werte.schule’ (school worth living. The vision of the Kingdom of God and the necessity of participation become apparent. DEUTSCH: Im ersten Teil werden sechs Stationen am Lebensweg des Autors beschrieben, die seine Auseinandersetzung mit Gerechtigkeit geprägt haben. Der zweite Teil gibt Einblick in seine religionspädagogische Arbeit, in der die Frage nach Gerechtigkeit besonders bedeutsam war am Beispiel ‚Religion im Kontext Migration‘ und der ökumenischen Initiative ‚lebens.werte.schule‘. Die Vision vom Reich Gottes und die Notwendigkeit von Partizipation werden dabei deutlich.

Theory of uniqueness of Indian Caste System

OpenAIRE

Ashwin Kumar

2006-01-01

Classical studies on pre-modern Indian social structure have suggested apparent differences between the Indian caste system and social stratification as one can discern in other parts of the world. However, one needs to question such dogmatic assertions that such vast differences really existed. An endeavor is made in this research paper to reflect on the nature of caste hierarchy in pre-modern India. The caste system forms the significant basis of pre-modern Indian social structure. Early wr...

The Angry Dying Patient.

Science.gov (United States)

Houston, Robert E.

1999-02-01

Over 25 years ago, Kubler-Ross identified anger as a predictable part of the dying process. When the dying patient becomes angry in the clinical setting, all types of communication become strained. Physicians can help the angry dying patient through this difficult time by using 10 rules of engagement. When physicians engage and empathize with these patients, they improve the patient's response to pain and they reduce patient suffering. When physicians educate patients on their normal responses to dying and enlist them in the process of family reconciliation, they can impact the end-of-life experience in a positive way.

Die Region braucht die Kultur - die Kultur braucht die Region

OpenAIRE

Klemm, Ulrich

1995-01-01

Die Region braucht die Kultur - die Kultur braucht die Region. - In: Region in Aktion - oder: Region im Abseits? - Boxberg-Wölchingen : Eigenständige Regionalentwicklung Baden-Württemberg, 1995. - S. 25 f.

DIE GESKIEDENIS VAN DIE PERSONEELFUNKSIE IN DIE SA ...

African Journals Online (AJOL)

stel (kortdiensstelsel). Met die uitbreek van die oorlog in 1939 het die. Unieverdedigingsmag uit 40% Staandemag en. 60% aktiewe Burgermag bestaan. Op 22 Sept. 1939 is magtiging aan die Aktiewe Burgermag- eenhede verleen om vrywilligers vir die duur van die oorlog te aanvaar. Agv beswaar dat die Verdedigingswet.

Causes of Cracking in Quenching of the Parts Made of Steels and Cast Iron and Recommendations for Their Removal: A Review

Science.gov (United States)

Kuznetsov, A. A.; Rudnev, V. I.

2017-12-01

The domestic and foreign experience on revealing the causes of quenching cracking and its prevention is generalized. We consider the works performed on the machine parts made of carbon and alloyed pearlitic steel and quenchable cast irons.

When Somebody Dies

Science.gov (United States)

... bottle became useless. The container is gone, but what's inside — the water — remains. The part of a person that's left after the body dies is often called the "soul" or "spirit." Some people believe the soul is the part ...

A Casting Yield Optimization Case Study: Forging Ram

DEFF Research Database (Denmark)

Kotas, Petr; Tutum, Cem Celal; Hattel, Jesper Henri

2010-01-01

This work summarizes the findings of multi-objective optimization of a gravity sand-cast steel part for which an increase of the casting yield via riser optimization was considered. This was accomplished by coupling a casting simulation software package with an optimization module. The benefits...... of this approach, recently adopted in foundry industry world wide and based on fully automated computer optimization, were demonstrated. First, analyses of filling and solidification of the original casting design were conducted in the standard simulation environment to determine potential flaws and inadequacies...

Nodular cast iron and casting monitoring

Directory of Open Access Journals (Sweden)

S. Pietrowski

2008-10-01

Full Text Available In this paper quality monitoring of nodular cast iron and casting made of it is presented. A control system of initial liquid cast iron to spheroidization, after spheroidization and inoculation with using of TDA method was shown. An application of an ultrasonic method to assessment of the graphite form and the metal matrix microstructure of castings was investigated.

Non-destructive control of castings

International Nuclear Information System (INIS)

Boutault, J.; Mascre, C.

1978-01-01

The object of non-destructive control in foundries is to verify the metal structure, the absence of unacceptable discontinuity, total tightness, etc. This leads to a range of very varied controls according to the importance of the series, the quality level required by the specifications, the nature of the alloy. The originality of the solutions which are imperative for castings is shown through examples: casting of high quality complex forms in short series; very thick unit parts; very large series of parts requiring on efficient automation of non-destructive control. Lastly the publishing of testing methods and interpretating rules, which are the base of a friendly understanding between constructors and founders are recalled [fr

Die-cast heterophase composites with AlSi13Mg1CuNi matrix

Directory of Open Access Journals (Sweden)

M. Dyzia

2010-01-01

Full Text Available On the basis of the performed tests, an advantageous interaction of glassy carbon particles in a couple consisting of a heterophase composite and a spheroidal cast iron has been corroborated. It was found that, the presence of glassy carbon in the heterophase composite (SiC+C affects the stabilization of the friction coefficient value as a function of the friction distance and reduces the intensity of the wearing-in stage of the interacting surfaces. Both a decrease of the friction coefficient and the wear of the heterophase composites may be connected with the carbon particles' chipping effect and the deposition of its fragments on the surface of the interacting components of the friction couple, which forms a kind of a solid lubricating agent in the system. This should allow applying of this material to the composite piston - cylinder sleeve system in piston air-compressors. Further works will concern the selection of the matrix alloy composition with the purpose of reducing the phenomenon of particles chipping during machining. It seems that one of the possibilities is the application of a more plastic matrix and optimizing the fraction of reinforcing phases and their gradient distribution in the casting.

Investigation of microporosity in die-cast AlSi12(Cu) alloys by neutron- and X-ray radiography

International Nuclear Information System (INIS)

Zsolt, S.; Marton, B.

1999-01-01

The porosity of the casting can dramatically reduce the solidity and reliability of the objects made from aluminum alloys. The X-ray radiography is able to find the placement of the porosity of the aluminum devices. After a special 'water saturation' process the dynamic neutron radiography is available to discover the 'dangerous' surface nearporosity in the aluminum samples. The X-ray and neutron radiography were used as complementary examination techniques to study the porosity of the aluminum castings.(author)

49 CFR 192.373 - Service lines: Cast iron and ductile iron.

Science.gov (United States)

2010-10-01

... 49 Transportation 3 2010-10-01 2010-10-01 false Service lines: Cast iron and ductile iron. 192.373... Regulators, and Service Lines § 192.373 Service lines: Cast iron and ductile iron. (a) Cast or ductile iron... cast iron pipe or ductile iron pipe is installed for use as a service line, the part of the service...

Improvement of Artistic Cast Production System

Directory of Open Access Journals (Sweden)

Władysiak R.

2017-09-01

Full Text Available The paper presents the technology and organization of the artistic cast production. On the basis of the actual cast production system, the manufacturing process was shown, in particular sand–piece moulding, which is a very important process and a time-consuming part of the entire manufacture of the casts. The current state of the production process as well as the organization of the work and production technology were analysed with the use of methods and techniques of production improvement, the Lean Manufacturing concept and computer systems. The results of the analysis and studies were shown with use of schemes and graphs of the layout of the production resources, a flow chart of the production process, value stream mapping, and a costs table for the production and modernization of the moulding stage. The work has shown that there are possibilities to improve the artistic cast production system. This improvement leads to increased productivity, lower production costs of artistic casts and increased competitiveness of the foundry.

Open die forging of large shafts with porosity defects – physical and numerical modelling

DEFF Research Database (Denmark)

Christiansen, Peter; Hattel, Jesper Henri; Bay, Niels

2013-01-01

The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V-shaped d......The aim and scope of this paper is centered to analyze the influence of the geometry of V-shaped dies on the closure of internal centerline porosity defects in ingots during multistep open-die forging. The investigation is performed with small scale physical models made from lead using V......-shaped dies with 90o and 120o and a reference pair of flat parallel platens. Holes drilled through the center of these preforms are produced to mimic centerline porosity in full scale cast ingots and intermediate rotation of the preforms replicate a multi-stage forging sequence under laboratory testing...

Effect of Titanium Inoculation on Tribological Properties of High Chromium Cast Iron

Directory of Open Access Journals (Sweden)

Siekaniec D.

2017-12-01

Full Text Available The present investigation focuses on the study of the influence of titanium inoculation on tribological properties of High Chromium Cast Iron. Studies of tribological properties of High Chromium Cast Iron, in particularly the wear resistance are important because of the special application of this material. High Chromium Cast Iron is widely used for parts that require high wear resistance for example the slurry pumps, brick dies, several pieces of mine drilling equipment, rock machining equipment, and similar ones. Presented research described the effects of various amounts of Fe-Ti as an inoculant for wear resistance. The results of wear resistance were collated with microstructural analysis. The melts were conducted in industrial conditions. The inoculation was carried out on the stream of liquid metal. The following amount of inoculants have been used; 0.17% Fe-Ti, 0.33% Fe-Ti and 0.66% Fe-Ti. The tests were performed on the machine type MAN. The assessment of wear resistance was made on the basis of the weight loss. The experimental results indicate that inoculation improve the wear resistance. In every sample after inoculation the wear resistance was at least 20% higher than the reference sample. The best result, thus the smallest wear loss was achieved for inoculation by 0.66% Fe-Ti. There is the correlation between the changing in microstructure and wear resistance. With greater amount of titanium the microstructure is finer. More fine carbides do not crumbling so quickly from the matrix, improving the wear resistance.

Die posisie van die Helper in die sending

Directory of Open Access Journals (Sweden)

I. J. van der Walt

1972-05-01

Full Text Available Gedurende die aanvangsjare van die sending het die helper ’n onmisbare funksie vervul. Hulle het die onherbergsame binnelande geken, waardevolle kontakpunte vir die sendelinge geopen en hulle mense geestelik help voorlig en voorberei.

Effect of storage time and framework design on the accuracy of maxillary cobalt-chromium cast removable partial dentures

Science.gov (United States)

Viswambaran, M.; Sundaram, R. K.

2015-01-01

Statement of Problem: Inaccuracies in the fit of palatal major connectors may be related to distortion of the wax pattern due to prolonged storage time and faulty major connector design. Purpose: This in vitro study was carried out to find out the effect of storage time and major connector design on the accuracy of cobalt-chromium cast removable partial dentures (RPDs). Materials and Methods: A brass metal die with a Kennedy Class III, modification 1, the partially edentulous arch was used as a master die. Thirty-six refractory casts were fabricated from the master die. The refractory casts were divided into three groups (Group I: Anterior-posterior palatal bar, Group II: Palatal strap and Group III: Palatal plate) based on the design of maxillary major connector and subdivided into four groups (sub Group A: 01 h, sub Group B: 03 h, Sub Group C: 06 h, and sub Group D: 24 h) based on the storage time. For each group, 12 frameworks were fabricated. The influence of wax pattern storage time and the accuracy of the fit palatal major connector designs on the master die were compared. Casting defects (nodules/incompleteness) of the frameworks were also evaluated before finishing and polishing. Repeated measures analysis of variance was used to analyze the data. Results: The gap discrepancy was least in sub Group A (01 h) followed by sub Group B (03 h) and C (06 h) and most in sub Group D (24 h). Statistically significant differences (P < 0.05 in all locations L1–L5) in the fit of the framework were related to the design of the major connector. The gap discrepancy was least in Group I (anterior-posterior palatal bar) followed by Group II (palatal strap) and most in Group II (palatal plate). Conclusions: It is recommended that the wax patterns for RPD to be invested immediately on completion of the wax procedure. The selection of a major connector design is crucial for an accurate fit of RPD. PMID:26681850

Effect of storage time and framework design on the accuracy of maxillary cobalt-chromium cast removable partial dentures

Directory of Open Access Journals (Sweden)

M Viswambaran

2015-01-01

Full Text Available Statement of Problem: Inaccuracies in the fit of palatal major connectors may be related to distortion of the wax pattern due to prolonged storage time and faulty major connector design. Purpose: This in vitro study was carried out to find out the effect of storage time and major connector design on the accuracy of cobalt-chromium cast removable partial dentures (RPDs. Materials and Methods: A brass metal die with a Kennedy Class III, modification 1, the partially edentulous arch was used as a master die. Thirty-six refractory casts were fabricated from the master die. The refractory casts were divided into three groups (Group I: Anterior-posterior palatal bar, Group II: Palatal strap and Group III: Palatal plate based on the design of maxillary major connector and subdivided into four groups (sub Group A: 01 h, sub Group B: 03 h, Sub Group C: 06 h, and sub Group D: 24 h based on the storage time. For each group, 12 frameworks were fabricated. The influence of wax pattern storage time and the accuracy of the fit palatal major connector designs on the master die were compared. Casting defects (nodules/incompleteness of the frameworks were also evaluated before finishing and polishing. Repeated measures analysis of variance was used to analyze the data. Results: The gap discrepancy was least in sub Group A (01 h followed by sub Group B (03 h and C (06 h and most in sub Group D (24 h. Statistically significant differences (P < 0.05 in all locations L1–L5 in the fit of the framework were related to the design of the major connector. The gap discrepancy was least in Group I (anterior-posterior palatal bar followed by Group II (palatal strap and most in Group II (palatal plate. Conclusions: It is recommended that the wax patterns for RPD to be invested immediately on completion of the wax procedure. The selection of a major connector design is crucial for an accurate fit of RPD.

Strengthening effect of nano-scale precipitates in a die-cast Mg–4Al–5.6Sm–0.3Mn alloy

Energy Technology Data Exchange (ETDEWEB)

Yang, Qiang [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Bu, Fanqiang [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); University of Chinese Academy of Sciences, Beijing 100049 (China); Qiu, Xin [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Yangzhou Hongfu Aluminium Co. Ltd, Yangzhou 100049 (China); Li, Yangde; Li, Weirong [E-ande Scientific & Technology Co. Ltd, Dongguan 523000 (China); Sun, Wei [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Liu, Xiaojuan, E-mail: lxjuan@ciac.ac.cn [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China); Meng, Jian, E-mail: jmeng@ciac.jl.cn [State Key Laboratory of Rare Earth Resource Utilization, Changchun Institute of Applied Chemistry, Chinese Academy of Sciences, Changchun 130022 (China)

2016-04-25

In this paper we report a quantitative study of the age-hardening in the high-pressure die-cast Mg–4Al−5.6Sm−0.3Mn alloy. The results indicate that a number of nano-scale spherical precipitates identified as Al{sub 3}Sm using high-angle annular dark-field scanning transmission electron microscopy, precipitated in Mg matrix after aging at 150–225 °C, with no obvious changes on grain sizes, intermetallic phases formed during solidification, and dislocation densities. From the existing strengthening theory equations in which some lacking parameters were taken from the first-principles density functional theory (DFT) calculations, a quantitative insight into the strengthening mechanisms of the nano-scale precipitate was formulated. The results are in reasonable agreement with the experimental values, and the operative mechanism of precipitation strengthening was revealed as Orowan dislocation bypassing. - Highlights: • The yield strength of Mg–Al–Sm alloy was improved by aging treatment. • A number of nano-scale precipitates formed in matrix after aging treatments. • The nanoscale precipitate was confirmed as Al{sub 3}Sm based on the data of HAADF-STEM study. • The strengthening mechanisms of the nano-scale precipitate were quantitatively formulated. • The operative mechanism of precipitate strengthening is Orowan dislocation bypassing.

Corrosion Behavior of High Pressure Die Cast Al-Ni and Al-Ni-Ca Alloys in 3.5% NaCl Solution

Energy Technology Data Exchange (ETDEWEB)

Arthanari, Srinivasan; Jang, Jae Cheol; Shin, Kwang Seon [Seoul National University, Seoul (Korea, Republic of)

2017-06-15

In this investigation corrosion behavior of newly developed high-pressure die cast Al-Ni (N15) and Al-Ni-Ca (NX1503) alloys was studied in 3.5% NaCl solution. The electrochemical corrosion behavior was evaluated using open circuit potential (OCP) measurement, potentiodynamic polarization, and electrochemical impedance spectroscopy (EIS) techniques. Potentiodynamic polarization results validated that NX1503 alloy exhibited lower corrosion current density (i{sub corr}) value (5.969 μA/cm{sup 2}) compared to N15 (7.387 μA/cm{sup 2}). EIS-Bode plots revealed a higher impedance (|Z|) value and maximum phase angle value for NX1503 than N15 alloy. Equivalent circuit curve fitting analysis revealed that surface layer (R{sub 1}) and charge transfer resistance (R{sub ct}) values of NX1503 alloy was higher compared to N15 alloy. Immersion corrosion studies were also conducted for alloys using fishing line specimen arrangement to simultaneously measure corrosion rates from weight loss (P{sub W}) and hydrogen volume (P{sub H}) after 72 hours and NX1503 alloy had lower corrosion rate compared to N15 alloy. The addition of Ca to N15 alloy significantly reduced the Al{sub 3}Ni intermetallic phase and further grain refinement may be attributed for reduction in the corrosion rate.

Rapid die manufacturing - high pressure casting of low volume non ferrous metals components

CSIR Research Space (South Africa)

Pereira, MFV

2006-11-01

Full Text Available .csir.co.za Models of assembled Die Slide 12 © CSIR 2006 www.csir.co.za 3. Die manufacture, assembly and data capturing 21.521.521.525.5total 4electrode 3Fitting3Fitting3Fitting3Fitting 2Polish2Polish2Polish2Polish 7SER 3F grind3F grind...3F grind4F grind Heat trHeat trHeat tr1Heat tr Jig boreJig boreJig boreJig bore GrindingGrindingGrinding2Grinding 13.5DMLS13.5DMLS13.5DMLS2.5Milling HrsCostProcessHrsCostProcessHrsCostProcessHrsCostProcess Core 4Core 3Core 2Core 1 NB. Times...

Identification of the steel viscosity and dynamic yield stress for the numerical modelling of casting simulations in the semi-solid state

Directory of Open Access Journals (Sweden)

Solek K.

2017-03-01

Full Text Available Conditions of some casting processes cause flow of both liquid and semi-liquid metal alloys inside the die cavity. Generally, the continuous casting, squeeze casting or thixoforming could be classified as such processes. Design or optimisation of casting technology using numerical simulations requires knowledge of the rheological properties. The main objective of the experimental work, presented in this publication, is an analysis of the viscosity of 1.2080 (X210Cr12 high carbon steel in liquid and semisolid state. The secondary purpose of the experimental work was a development of the viscosity models used in continuous casting and thixoforming simulations. The significant achievement of this particular study was identification of thixotropy phenomenon which occurs not only during thixoforming, but also during magnetohydrodynamic stirring in continuous casting processes.

Analysis of nucleation modelling in ductile cast iron

DEFF Research Database (Denmark)

Moumeni, Elham; Tutum, Cem Celal; Tiedje, Niels Skat

2012-01-01

Heterogeneous nucleation of nodular graphite at inclusions in ductile iron during eutectic solidification has been investigated. The experimental part of this work deals with casting of ductile iron samples with two different inoculants in four different thicknesses. Chemical analysis, metallogra......Heterogeneous nucleation of nodular graphite at inclusions in ductile iron during eutectic solidification has been investigated. The experimental part of this work deals with casting of ductile iron samples with two different inoculants in four different thicknesses. Chemical analysis...

Thermal distortion of disc-shaped ductile iron castings in vertically parted moulds

DEFF Research Database (Denmark)

Vedel-Smith, Nikolaj Kjelgaard; Rasmussen, Jakob; Tiedje, Niels Skat

2015-01-01

A disc-shaped casting with an inner boss and an outer rim, separated by a thin walled section, was examined. This measurable deformation varied with the feeding modulus. The influence of alloy composition, particularly Si content, was examined with a pearlitic ductile iron (EN-GJS-500-7) and a fu......A disc-shaped casting with an inner boss and an outer rim, separated by a thin walled section, was examined. This measurable deformation varied with the feeding modulus. The influence of alloy composition, particularly Si content, was examined with a pearlitic ductile iron (EN-GJS-500......-7) and a fully ferritic ductile iron (EN-GJS-450-10). The experiment showed that both the alloy composition and choice of feeder influenced the degreeof deformation measured in the finished casting. It was found that the deformation of the pearlitic alloy was influenced controllably by changing the feeder...

die ontstaan en die ontwikkeling van die skoolkadette-stelsel in die rsa

African Journals Online (AJOL)

toe algemene diensplig ingestel is. Die diens- plig het intussen sy volle beslag gekry en in. Weermagkringe het die gedagte posgevat dat skoolkadette. 'n deeglike ondersoek vereis ten einde die skoolgaande seun vir sy komende nasionale diensplig te orienteer. Tydens kadetopleldlng leer die seuns al die fynere kunsles ...

Influence of casting defects on fatigue strength of an investment cast Ti-6Al-4V alloy

Directory of Open Access Journals (Sweden)

Léopold Gaëlle

2014-06-01

Full Text Available The influence of casting defects on fatigue strength of an investment cast Ti-6Al-4V alloy is investigated. The most common of these defects are: pinhole, linear defect and inclusion. Each of them is currently defined by its size, morphology and position from the surface but is different from each other for a same type. An experimental campaign is defined with different types of defect. The first part of the campaign is focused on the influence of an artificial and spherical defect, considering two different surface conditions. It is shown that fatigue behaviour of this alloy is very sensitive to the surface condition of this artificial defect despite stress concentrations at the tip of the defect. The second part of the campaign is focused on casting defects: reduction of fatigue life is quantified and it is shown that an electro-discharge machined defect cannot be representative of pinhole.

INFLUENCE OF DIE ANGLES ON THE MICROHARDNESS OF ALUMINUM ALLOY PROCESSED BY EQUAL CHANNEL ANGULAR PRESSING

Directory of Open Access Journals (Sweden)

Ali A Aljubouri

2010-11-01

Full Text Available   The die geometry has a massive effect on the plastic deformation behavior during pressing of material processed by equal channel angular pressing (ECAP method; subsequently the properties of the processed material are strongly dependent on it. Two categories of designed and manufactured dies are used for equal channel angular pressing, a 1200 sharp angle and a 900 round –cornered (200 dies, that produce strain per pass through both dies of ~0.7 and ~1.05   respectively. The microhardness developed in Al-Si alloy during ECAP using route BC. The microhardness increased by a factor of >1.5, after only 1 pressing. Subsequently, the hardness increases slightly up to 8 pressings through the 1200 sharp angle die, while it is increased by a factor of ~2.6 after 5 passes by using the 900 round cornered die, comparing with that for the cast workpiece.

Steel castings of valves for nuclear power station

International Nuclear Information System (INIS)

Yamasaki, Yutaka

1975-01-01

The manufacturing of the steel castings of valves for nuclear power plants is reported. The report is divided in six parts. The first part describes the reliability of the steel castings of valves for nuclear power plants. Particular attention must be paid to larger diameter and lower pressure rating for the valves in nuclear power plants than those in thermal power plants. The second part describes the characteristics of steel casting quality, defects and their cause. The defects that may be produced in steel castings are as follows: (a) cavities caused by the insufficient supply of molten steel, (b) sand bites caused by the mold destruction due to thermal shock, and (c) pinholes caused by the gas absorption of molten steel. The third part describes the clarification of quality level and the measures quality project. Gaseous defects and the indications detected by magnetic powder test are attributed to electric furnace steel making. In particular, the method to minimize gas content is important. The fourth part describes the quality control of manufacturing processes. In practice, thirteen semi-automatic testers using gamma radiation are employed. A full automatic inspection plant having capacity of 20,000 radiographs per month is under design. The fifth part describes a quality warrant system. A check sheet system concerning quality and safety is employed in all work shops. The reliability of all testers and measuring instruments as well as the skill of workmen are examined periodically. The seventh part deals with future problems. The manufacturing plan must be controlled so that non-destructive inspection becomes the main means for quality control. (Iwakiri, K.)

The role and impact of 3D printing technologies in casting

Directory of Open Access Journals (Sweden)

Jin-wu Kang

2017-05-01

Full Text Available 3D printing is such a magical technology that it extends into almost every sector relating to manufacturing, not to mention casting production. In this paper, the past, present and future of 3D printing in the foundry sector are profoundly reviewed. 3D printing has the potential to supplement or partially replace the casting method. Today, some castings can be directly printed by metal powders, for example, titanium alloys, nickel alloys and steel parts. Meanwhile, 3D printing has found an unique position in other casting aspects as well, such as printing the wax pattern, ceramic shell, sand core, sand mould, etc. Most importantly, 3D printing is not just a manufacturing method, it will also revolutionize the design of products, assemblies and parts, such as castings, patterns, cores, moulds and shells in casting production. The solid structure of castings and moulds will be redesigned in future into truss or spatially open and skeleton structures. This kind of revolution is just sprouting, but it will bring unimaginable impact on manufacturing including casting production. Nobody doubts the potential of 3D printing technologies in manufacturing, but they do have limitations and drawbacks.

The Influence of Home Scrap on Porosity of MgAl9Zn1 Alloy Pressure Castings

Directory of Open Access Journals (Sweden)

Konopka Z.

2017-03-01

Full Text Available The work presents the results of examinations concerning the influence of various amounts of home scrap additions on the porosity of castings made of MgAl9Zn1 alloy. The fraction of home scrap in the metal charge ranged from 0 to 100%. Castings were pressure cast by means of the hot-chamber pressure die casting machine under the industrial conditions in one of the domestic foundries. Additionally, for the purpose of comparison, the porosity of specimens cut out directly of the MgAl9Zn1 ingot alloy was also determined. The examinations consisted in the qualitative assessment of porosity by means of the optical microscopy and its quantitative determination by the method of weighting specimens in air and in water. It was found during the examination that the porosity of castings decreases with an increase in the home scrap fraction in the metal charge. The qualitative examinations confirmed the beneficial influence of the increased home scrap fraction on the porosity of castings. It was concluded that the reusing of home scrap in a foundry can be a good way of reduction of costs related to the production of pressure castings.

Development of industry processes simulators. Part III (Continuous casting)

International Nuclear Information System (INIS)

Ramirez, A.; Morales, R.; Morales, A. J.; Ramos, A.; Solorio, G.

2006-01-01

This work written for illustrating the use of Monte Carlo methods and generating of random number in combination with the information of the simulation system of thermal behaviour described previously in order to reproduce in a computer the solidification process of the steel and simulate the formation of strictures of casting step by step. (Author). 12 refs

Effect of dental technician disparities on the 3-dimensional accuracy of definitive casts.

Science.gov (United States)

Emir, Faruk; Piskin, Bulent; Sipahi, Cumhur

2017-03-01

Studies that evaluated the effect of dental technician disparities on the accuracy of presectioned and postsectioned definitive casts are lacking. The purpose of this in vitro study was to evaluate the accuracy of presectioned and postsectioned definitive casts fabricated by different dental technicians by using a 3-dimensional computer-aided measurement method. An arch-shaped metal master model consisting of 5 abutments resembling prepared mandibular incisors, canines, and first molars and with a 6-degree total angle of convergence was designed and fabricated by computer-aided design and computer-aided manufacturing (CAD-CAM) technology. Complete arch impressions were made (N=110) from the master model, using polyvinyl siloxane (PVS) and delivered to 11 dental technicians. Each technician fabricated 10 definitive casts with dental stone, and the obtained casts were numbered. All casts were sectioned, and removable dies were obtained. The master model and the presectioned and postsectioned definitive casts were digitized with an extraoral scanner, and the virtual master model and virtual presectioned and postsectioned definitive casts were obtained. All definitive casts were compared with the master model by using computer-aided measurements, and the 3-dimensional accuracy of the definitive casts was determined with best fit alignment and represented in color-coded maps. Differences were analyzed using univariate analyses of variance, and the Tukey honest significant differences post hoc tests were used for multiple comparisons (α=.05). The accuracy of presectioned and postsectioned definitive casts was significantly affected by dental technician disparities (Ptechnician differences. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

Die funksie van die skeppingstradisie in die boek Jeremia

African Journals Online (AJOL)

gedeeites voor wat sterk ooreenkomste toon met die beskrywings van die skep pingsgebeure in die boek Jeremia. • Volgpns Von Rad (1957:144-146) het daar wel 'n groep bestaan wat belange ge- had liet by die oorlewering van die skeppingstradisies. Dit was waarskynlik die. Sadokitiese priesters wat om twee redes aan ...

Cast iron repair method of stitching pin

International Nuclear Information System (INIS)

Yun, In Sik; Yu, Yeong Chul; Kim, Steve S.; Reed, Gary J.

2003-01-01

Many cast iron parts are welded and suffer from improper pre-heating and poor welding skills which destroy the castings due to new cracks, deformations etc. This is due mainly to the lack of understanding of the properties of cast iron. Welding, however impractical, was the only alternative for many years. Locks are used to add strength across a crack. Special drilling jigs are used to create a precise hole pattern that locks are driven into. Our locks have a unique ability to pull the sides of a crack together. Bottom locks are stacked or laminated to a depth of 80% of the casting thickness. Thicker surface locks finish off lock installation, allowing repairs in irregular shapes and contours. Installing products can be done quickly with pneumatic tools. Up to one inch of repair can be done in 5 minutes in 1/4 inch thick cast iron.

Die binding van die konfessie

Directory of Open Access Journals (Sweden)

P. J. Coetzee

1970-05-01

Full Text Available Ons moet waak teen twee uiterstes. Aan die een kant het die dogma as onversoenlike vyand die dogmatisme en aan die ander kant die antidogmatisme — dit hou enersyds die gevaar in van verabsolutering (oorskatting, en ander- syds die gevaar van relativisme (onderskatting.

Die nabyheid van die Koninkryk

Directory of Open Access Journals (Sweden)

W.J. Snyman

1963-03-01

Full Text Available Vanweë die belangrikheid daarvan volg hier ’n breër bespreking van die proefskrif van dr. Tjaart van der Walt oor die nabyheid van die Koninkryk as wat in ’n gewone resensie kan geskied. Die vraagstuk wat onder oë gesien word is so oud as die kerk en die teologie, soms minder en soms meer op die voorgrond. Tans kan gesê word, staan dit in die middelpunt. Daarby is dit nie maar ’n akademiese vraagstuk nie, maar ’n vraagstuk waarvoor elke nadenkende leser van die Skrif te staan kom.

Preliminary physical, nutrients, biological, meteorological, and other data from bottle casts, CTD casts, ADCP casts, moored current meters, and meteorological sensors from the GYRE from as part of the Texas-Louisiana Shelf Circulation and Transport Processes Study (LATEX PART A) from 04 November 1992 to 05 August 1994 (NODC Accession 9500054)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Preliminary physical, nutrients, biological, meteorological, and other data from bottle casts, CTD casts, ADCP casts, and meteorological sensors from the GYRE from...

Latest results of cast and future prospects

CERN Document Server

Vafeiadis, Theodoros

2014-01-01

CERN Axion Solar Telescope (CAST) is currently the most sensitive axion helioscope designed to search for axions and axion-like particles produced in the Sun. CAST completed successfully the second part of CAST phase II where the magnet bores were lled with 3He gas at variable pressure scanning axion masses up to 1.2 eV In the absence of signal it has set the best experimental limit on the axion-photon coupling constant over a broad range of axion masses. In 2013 CAST has improved its sensitivity to solar axions with rest mass below 0.02 eV by upgrading the Micromegas detectors and it will continue in 2014 with the implementation of a second X-ray optic and a new type detector (InGRID). In addition, CAST has extended its sensitivity into the sub-keV energy range using a silicon detector (SDD), to search for solar chameleons. Thus, CAST also became sensitive to dark energy particles. A new generation axion helioscope (IAXO) aims to improve the current axion-photon coupling by 1-1.5 orders of magnitude. This wi...

Accuracy of ringless casting and accelerated wax-elimination technique: a comparative in vitro study.

Science.gov (United States)

Prasad, Rahul; Al-Keraif, Abdulaziz Abdullah; Kathuria, Nidhi; Gandhi, P V; Bhide, S V

2014-02-01

The purpose of this study was to determine whether the ringless casting and accelerated wax-elimination techniques can be combined to offer a cost-effective, clinically acceptable, and time-saving alternative for fabricating single unit castings in fixed prosthodontics. Sixty standardized wax copings were fabricated on a type IV stone replica of a stainless steel die. The wax patterns were divided into four groups. The first group was cast using the ringless investment technique and conventional wax-elimination method; the second group was cast using the ringless investment technique and accelerated wax-elimination method; the third group was cast using the conventional metal ring investment technique and conventional wax-elimination method; the fourth group was cast using the metal ring investment technique and accelerated wax-elimination method. The vertical marginal gap was measured at four sites per specimen, using a digital optical microscope at 100× magnification. The results were analyzed using two-way ANOVA to determine statistical significance. The vertical marginal gaps of castings fabricated using the ringless technique (76.98 ± 7.59 μm) were significantly less (p castings fabricated using the conventional metal ring technique (138.44 ± 28.59 μm); however, the vertical marginal gaps of the conventional (102.63 ± 36.12 μm) and accelerated wax-elimination (112.79 ± 38.34 μm) castings were not statistically significant (p > 0.05). The ringless investment technique can produce castings with higher accuracy and can be favorably combined with the accelerated wax-elimination method as a vital alternative to the time-consuming conventional technique of casting restorations in fixed prosthodontics. © 2013 by the American College of Prosthodontists.

Abrasive Wear of Alloyed Cast Steels Applied for Heavy Machinery

Directory of Open Access Journals (Sweden)

Studnicki A.

2015-03-01

Full Text Available In the paper the results and analysis of abrasive wear studies were shown for two grades of cast steels: low-alloyed cast steel applied for heavy machinery parts such as housing, covers etc. and chromium cast steels applied for kinetic nodes of pin-sleeve type. Studies were performed using the modified in Department of Foundry pin-on-disc method.

Bainite obtaining in cast iron with carbides castings

Directory of Open Access Journals (Sweden)

S. Pietrowski

2010-01-01

Full Text Available In these paper the possibility of upper and lower bainite obtaining in cast iron with carbides castings are presented. Conditions, when in cast iron with carbides castings during continuous free air cooling austenite transformation to upper bainite or its mixture with lower bainte proceeds, have been given. A mechanism of this transformation has been given, Si, Ni, Mn and Mo distribution in the eutectic cell has been tested and hardness of tested castings has been determined.

Repair welding of cast iron coated electrodes

Science.gov (United States)

Żuk, M.; Górka, J.; Dojka, R.; Czupryński, A.

2017-08-01

Welding cast iron is a complex production procedure. Repair welding was used to repair damaged or poorly made castings. This is due to a tendency to cracking of the material during welding as well as after it. Welding cast iron can be carried out on hot or on cold. Hot welding requires high heat material and the use of welding material in the form of cast iron. In the case of cold welding, it is possible to use different materials. Mostly used filler metals are nickel and copper based. The work shows the course of research concerning repairmen of ductile iron with arc welding method. For the reparation process four types of ESAB company coated electrodes dedicated for cast iron were used with diameter 3.2 and 4 mm: ES 18-8-6B (4mm), EB 150 (4mm), OK NiCl, EŻM. In the cast iron examined during the testing grooves were made using plasma methods, in order to simulate the removed casting flaws. Then the welding process with coated electrodes was executed. The process utilized low welding current row of 100A, so there would only be a small amount of heat delivered to the heat affected zone (HAZ). Short stitches were made, after welding it was hammered, in order to remove stresses. After the repair welding the part of studies commenced which purpose was finding surface defects using visual testing (VT) and penetration testing (PT). In the second part, a series of macro and microscopic studies were executed witch the purpose of disclosuring the structure. Then the hardness tests for welds cross sections were performed. An important aspect of welding cast iron is the colour of the padding weld after welding, more precisely the difference between the base material and padding weld, the use of different materials extra gives the extra ability to select the best variant. The research of four types of coated electrode was executed, based on the demands the best option in terms of aesthetic, strength and hardness.

Neutron radiography inspection of investment castings

International Nuclear Information System (INIS)

Richards, W.J.; Barrett, J.R.; Springgate, M.E.; Shields, K.C.

2004-01-01

Investment casting, also known as the lost wax process, is a manufacturing method employed to produce near net shape metal articles. Traditionally, investment casting has been used to produce structural titanium castings for aero-engine applications with wall thickness less than 1 in (2.54 cm). Recently, airframe manufacturers have been exploring the use of titanium investment casting to replace components traditionally produced from forgings. Use of titanium investment castings for these applications reduces weight, cost, lead time, and part count. Recently, the investment casting process has been selected to produce fracture critical structural titanium airframe components. These airframe components have pushed the traditional inspection techniques to their physical limits due to cross sections on the order of 3 in (7.6 cm). To overcome these inspection limitations, a process incorporating neutron radiography (n-ray) has been developed. In this process, the facecoat of the investment casting mold material contains a cocalcined mixture of yttrium oxide and gadolinium oxide. The presence of the gadolinium oxide, allows for neutron radiographic imaging (and eventual removal and repair) of mold facecoat inclusions that remain within these thick cross sectional castings. Probability of detection (POD) studies have shown a 3x improvement of detecting a 0.050x0.007 in 2 (1.270x0.178 mm 2 ) inclusion of this cocalcined material using n-ray techniques when compared to the POD using traditional X-ray techniques. Further, it has been shown that this n-ray compatible mold facecoat material produces titanium castings of equal metallurgical quality when compared to the traditional materials. Since investment castings can be very large and heavy, the neutron radiography facilities at the University of California, Davis McClellan Nuclear Radiation Center (UCD/MNRC) were used to develop the inspection techniques. The UCD/MNRC has very unique facilities that can handle large parts

A Membrane Process for Recycling Die Lube from Wastewater Solutions

Energy Technology Data Exchange (ETDEWEB)

Eric S. Peterson; Jessica Trudeau; Bill Cleary; Michael Hackett; William A. Greene

2003-04-01

An active-surface membrane technology was used to separate a die lube manufacturing wastewater stream consisting of various oils, hydrocarbons, heavy metals, and silicones. The ultrafiltration membranes reduced organics from initial oil and grease contents by 20–25X, carbon oxygen demand (COD) by 1.5 to 2X, and total organic carbon (TOC) by 0.6, while the biological oxygen demand (BOD) remained constant. The active-surface membranes were not fouled as badly as non-active-surface systems and the active-surface membrane flux levels were consistently higher and more stable than those of the non-active-surface membranes tested. Field testing demonstrated that the rotary microfilter can concentrate the die lube, i.e. remove the glycerin component, and produce a die lube suitable for recycling. The recycling system operated for six weeks with only seven cleaning cycles and no mechanical or electrical failures. Test data and quality records indicate that the die casting scrap was reduced from 8.4 to 7.8%. There is no doubt that this test yielded tremendous results. This separation process presents significant opportunities that can be evaluated further.

A Membrane Process for Recycling Die Lube from Wastewater Solutions

Energy Technology Data Exchange (ETDEWEB)

Peterson, E. S. [Idaho National Lab. (INL), Idaho Falls, ID (United States); Trudeau, J. [Metaldyne, Inc., Twinsburg, OH (United States); Cleary, B. [Metaldyne, Inc., Twinsburg, OH (United States); Hackett, M. [Metaldyne, Inc., Twinsburg, OH (United States); Greene, W. A. [SpinTek FIltrations, LLC, Los Alamitos, CA (United States)

2003-04-30

An active-surface membrane technology was used to separate a die lube manufacturing wastewater stream consisting of various oils, hydrocarbons, heavy metals, and silicones. The ultrafiltration membranes reduced organics from initial oil and grease contents by 20-25X, carbon oxygen demand (COD) by 1.5 to 2X, and total organic carbon (TOC) by 0.6, while the biological oxygen demand (BOD) remained constant. The active-surface membranes were not fouled as badly as non-active-surface systems and the active-surface membrane flux levels were consistently higher and more stable than those of the non-active-surface membranes tested. Field testing demonstrated that the rotary microfilter can concentrate the die lube, i.e. remove the glycerin component, and produce a die lube suitable for recycling. The recycling system operated for six weeks with only seven cleaning cycles and no mechanical or electrical failures. Test data and quality records indicate that the die casting scrap was reduced from 8.4 to 7.8%. There is no doubt that this test yielded tremendous results. This separation process presents significant opportunities that can be evaluated further.

Melting and casting of FeAl-based cast alloy

Energy Technology Data Exchange (ETDEWEB)

Sikka, V.K. [Oak Ridge National Lab., TN (United States); Wilkening, D. [Columbia Falls Aluminum Co., Columbia Falls, MT (United States); Liebetrau, J.; Mackey, B. [AFFCO, L.L.C., Anaconda, MT (United States)

1998-11-01

The FeAl-based intermetallic alloys are of great interest because of their low density, low raw material cost, and excellent resistance to high-temperature oxidation, sulfidation, carburization, and molten salts. The applications based on these unique properties of FeAl require methods to melt and cast these alloys into complex-shaped castings and centrifugal cast tubes. This paper addresses the melting-related issues and the effect of chemistry on the microstructure and hardness of castings. It is concluded that the use of the Exo-Melt{trademark} process for melting and the proper selection of the aluminum melt stock can result in porosity-free castings. The FeAl alloys can be melted and cast from the virgin and revert stock. A large variation in carbon content of the alloys is possible before the precipitation of graphite flakes occurs. Titanium is a very potent addition to refine the grain size of castings. A range of complex sand castings and two different sizes of centrifugal cast tubes of the alloy have already been cast.

NWIS casting measurements taken during demonstrations to Russian visitors

International Nuclear Information System (INIS)

Mullens, J.A.; Valentine, T.E.; Mihalczo, J.T.

1998-01-01

This report describes a set of NWIS measurements made during demonstrations to Russian visitors on August 28, 1997. These measurements will be given to the Russian visitors from Arzamus-16 as part of their NWIS training (part of a DOE laboratory-to-laboratory exchange program). These measurements are made on standard highly enriched Uranium annular castings (as used for storage). Associated NWIS calibration runs were made in air (no casting, just the NWIS Californium source and detectors)

Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus

Directory of Open Access Journals (Sweden)

M. M. Nel

1990-07-01

Full Text Available Die histologie en ultrastruktuur van die hepatopankreas van die bloukurper Oreochromis mossambicus word beskryf. ’n Dun bindweefselkapsel omring die lewer. Die hepatosietrangskikking vertoon as lobules, met die koorde van hepatosiete wat vanaf ’n sentrale vene uitradieer en met mekaar anastomaseer. Indiwiduele lewerlohules vertoon nie duidelike grense nie, maar enkele duidelike triades word wel in die lewer van O. mossambicus aangetref. Die hepatosiete bevat ’n enkele ronde kern met ’n duidelike nukleolus en die growwe endoplasmiese retikula kom in twee of meer rye om die kerne en teen die selgrense van die hepatosiete voor. Die ander sitoplasmiese organelle kom verspreid in die hepatosietsitoplasma voor. Die eksokriene pankreasselle is om die portale venes gesetel. Die kerne van hierdie selle is rond en is hasaal in die kubies- tot silindervormige selle gelee. ’n Goedontwikkelde growwe endoplasmiese retikulum — vesikulêr, tubulêr en sirkulêr in vorm — en sektretoriese granules wat apikaal in die sel gelee is, kom voor.

National Metal Casting Research Institute final report. Development of an automated ultrasonic inspection cell for detecting subsurface discontinuities in cast gray iron. Volume 3

Energy Technology Data Exchange (ETDEWEB)

Burningham, J.S. [University of Northern Iowa, Cedar Falls, IA (United States). Dept. of Industrial Technology

1995-08-01

This inspection cell consisted of an ultrasonic flaw detector, transducer, robot, immersion tank, computer, and software. Normal beam pulse-echo ultrasonic nondestructive testing, using the developed automated cell, was performed on 17 bosses on each rough casting. Ultrasonic transducer selection, initial inspection criteria, and ultrasonic flow detector (UFD) setup parameters were developed for the gray iron castings used in this study. The software were developed for control of the robot and UFD in real time. The software performed two main tasks: emulating the manual operation of the UFD, and evaluating the ultrasonic signatures for detecting subsurface discontinuities. A random lot of 105 castings were tested; the 100 castings that passed were returned to the manufacturer for machining into finished parts and then inspection. The other 5 castings had one boss each with ultrasonic signatures consistent with subsurface discontinuities. The cell was successful in quantifying the ultrasonic echo signatures for the existence of signature characteristics consistent with Go/NoGo criteria developed from simulated defects. Manual inspection showed that no defects in the areas inspected by the automated cell avoided detection in the 100 castings machined into finished parts. Of the 5 bosses found to have subsurface discontinuities, two were verified by manual inspection. The cell correctly classified 1782 of the 1785 bosses (99.832%) inspected.

Additive Manufacturing and Casting Technology Comparison: Mechanical Properties, Productivity and Cost Benchmark

Science.gov (United States)

Vevers, A.; Kromanis, A.; Gerins, E.; Ozolins, J.

2018-04-01

The casting technology is one of the oldest production technologies in the world but in the recent years metal additive manufacturing also known as metal 3D printing has been evolving with huge steps. Both technologies have capabilities to produce parts with internal holes and at first glance surface roughness is similar for both technologies, which means that for precise dimensions parts have to be machined in places where precise fit is necessary. Benchmark tests have been made to find out if parts which are produced with metal additive manufacturing can be used to replace parts which are produced with casting technology. Most of the comparative tests have been made with GJS-400-15 grade which is one of the most popular cast iron grades. To compare mechanical properties samples have been produced using additive manufacturing and tested for tensile strength, hardness, surface roughness and microstructure and then the results have been compared with the samples produced with casting technology. In addition, both technologies have been compared in terms of the production time and production costs to see if additive manufacturing is competitive with the casting technology. The original paper has been written in the Latvian language as part of the Master Thesis within the framework of the production technology study programme at Riga Technical University.

Assembly optimization realized by a die-cast magnesium construction; Montageverbesserungen verwirklicht durch eine Magnesium-Druckguss-Konstruktion

Energy Technology Data Exchange (ETDEWEB)

Tikal, F.; Vollmer, C.; Pippert, J.

1996-11-01

Vehicle development today cannot be envisaged without non-contact and slip free distance- and speed-measurement. As it is superior to contact methods in terms of reliability and accuracy, it has gained more and more acceptance in the past few years and now provides measurement results of the utmost precision. This is particularly necessary in the large application range of tyre and vehicle development to ensure high safety levels; moreover, it is required for future vehicle control systems, as they need precise speed information for ABS, ASC, or for navigation methods. In principle, optical acoustic and microwave sensors can be used for these applications. The microwave sensors can be used for these applications. The microwave-Doppler principle provides certain advantages over optical or ultrasound methods as it can be used under any weather conditions and provides a larger vertical operating range and a long lifespan. Datron-Messtechnik, market leader in the field of correlator optical speed sensors, has made use of this measurement principle and with its microwave sensor introduces a new development covering the great demands of speed measurement. (orig.) [Deutsch] Die Pkw-Tuer, ein Bestandteil der Karosserie, ist im Laufe der Automobilgeschichte nicht wesentlich veraendert worden. Jedoch mussten in den letzten Jahren Flankenschutz, Seitenairbag und andere neue Bauteile in die Tuer integriert werden. Diese Elemente der passiven Sicherheit sind vom Verbraucher gewuenschte Schutzmassnahmen. Mit dem gehobenen Sicherheitsimage bemuehen sich die Produzenten, den potentiellen Kaeufer zum Kauf ihres Produktes zu bewegen. Am Institut fuer Produktionstechnik und Logistik (IPL) der Universitaet Gesamthochschule Kassel (GhK) wurde eine Pkw-Tuer, basierend auf einem Magnesium-Druckgussrahmen, entwickelt. Zur Orientierung und Studienzwecken ist ein Holzmodell erstellt worden. Mit dem praxisnahen Modell konnte die Montage und der Einbau in das Automobil getestet werden. Das

Cast Iron in The 19th Century Building Equipment

Science.gov (United States)

Kwasek, Michał; Piwek, Aleksander

2017-10-01

Cast iron is a material, characteristics of which enable to receive extremely artistic elements. It maintains good strength properties at the same time. That combination of these seemingly contrary traits makes it a commodity that was widely used in the 19th century industry and architecture. These usages were not only as decorative elements, technical and structural ones. The production of new household utilities started, which made people’s lives more comfortable. Cast iron allowed for fast and cheap production while maintaining high aesthetic qualities. Useful elements, which often were ornamental parts of buildings were created. The aim of the article is to characterise elements of interior equipment of the 19th century building that are made of cast iron. As it appears from performed bibliography, archival and field studies, the ways of exploitation are very broad. Some were mounted into the building; the others were a mobile equipment. As it occurred they were most commonly used as functional items. Cast iron was used to produce the minor elements, which were only parts of the bigger wooden or stone items. Notwithstanding, there were also bigger ones casted as a whole, and frequently ones that were assembled from many elements. Nowadays, elements of an interior feature are one of the subjects of study during the restoration work of the buildings. They can provide important information about the building and the way people lived and are considered as the essential part of historical objects.

Studies on the Castability of Pure Titanium (Part 3) Influence of casting pressure and sprue diameter on the titanium castability

OpenAIRE

YONEDA, TAKANORI; KUROIWA, AKIHIRO; IGARASHI, YOSHIMASA; OHNO, TAKAFUMI; SEKIGUCHI, YUUJI; INOUE, YOSHIHISA; MIGO, SHINYA

1998-01-01

We analyzed the external defects of castings with mesh grid patterns with 3 different kinds of phosphate bonded casting molds with 2 parameters (sprue diameter and casting pressure). Castability with pure titanium was affected by the parameters of sprue diameter, and casting pressure with different casting molds. The sprue condition was the most affective casting condition in the all directional pressure type casting machine. In 2 types of casting molds, one was strongly affected by the casti...

die impak van metodologie op die verstaan van die nuwe testament

African Journals Online (AJOL)

voorbeeld eers een maal deur die bril van die vorm- en redaksiekritiek na die Evangelies gekyk het, dink jy vir altyd anders oor hulle tot- standkoming. Inderdaad, nuwe metodes lei tot nuwe perspektiewe! Dit is dan ook waar die fokus van hierdie artikel val: die impak van metodologie op die verstaan van die Nuwe ...

Production of Steel Casts in Two-Layer Moulds with Alkaline Binders Part 2. Facing sand with the alkaline organic binder REZOLIT

Directory of Open Access Journals (Sweden)

M. Holtzer

2011-04-01

Full Text Available This paper constitutes the second part of the article concerning the implementation of the two-layer mould technology for steel casts inZ.M. POMET. The results of the laboratory examinations of the backing sand with the inorganic binder RUDAL were presented in thefirst part of the paper. Whereas in the second part the results of the laboratory testing of the facing sand with the alkaline resin REZOLITare given. The technology of two-layer moulds was already implemented in Z.M. POMET within the target project. Examples of castingsmade in this technology are shown in the final part of this paper.

Effects of microstructures on low cycle fatigue behavior in Al-Si-Mg cast alloys

International Nuclear Information System (INIS)

Han, Sang Won; Kim, Sug Won

2002-01-01

Low cycle fatigue tests were carried out using four kinds of Al-7%Si-0.4Mg cast alloys, i.e., two kinds of sand mold casts, permanent mold cast and semi-solid die cast. They were heat-treated in the condition of under aging and over aging to investigate effects of precipitates on fatigue. All tests were conducted under axial plastic strain amplitude control. Stress level of cyclic hardening curves increased sensitively with needle like eutectic Si particle, refine grain size and dendrite arm spacing (DAS). In particular, the refined grain structure of under aged matrix was more effective encourager for cyclic hardening compared with DAS and eutectic Si particle size. After rapid increase in cyclic hardening during several number of cycles, the stress amplitude kept increasing steadily until fracture in under aged alloys strengthened by shearable G.P. zone. On the other hand, over aged alloys strengthened by non-shearable β ' precipitates generated more drastic initial hardening and the stress amplitude reached the saturation state in quite early stage of the fatigue

Die vrede van Münster / Westfale en die betekenis daarvan vir die ...

African Journals Online (AJOL)

In die Suid-Afrikaanse kerkgeskiedenis egter is die Vrede van Münster as epogmakende gebeure tot dusver nie net in die algemeen verwaarloos nie, maar boonop is die direkte verband tussen hierdie sentrale historiese baken aan die een kant en aan die ander kant die vestiging van die VOC se verversingspos aan die ...

Gradient porous hydroxyapatite ceramics fabricated by freeze casting method

International Nuclear Information System (INIS)

Zuo Kaihui; Zhang Yuan; Jiang Dongliang; Zeng Yuping

2011-01-01

By controlling the cooling rates and the composition of slurries, the gradient porous hydroxyapatite ceramics are fabricated by the freeze casting method. According to the different cooling rate, the pores of HAP ceramics fabricated by gradient freeze casting are divided into three parts: one is lamellar pores, another is column pore and the last one is fine round pores. The laminated freeze casting is in favour of obtaining the gradient porous ceramics composed of different materials and the ceramics have unclear interfaces.

Microstructural evolution and wear characteristics of equal channel angular pressing processed semi-solid-cast hypoeutectic aluminum alloys

International Nuclear Information System (INIS)

Thuong, Nguyen Van; Zuhailawati, Hussain; Seman, Anasyida Abu; Huy, Tran Duc; Dhindaw, Brij Kumar

2015-01-01

Highlights: • We produced aluminum feedstock for ECAP by two casting techniques: conventional and with cooling slope. • Globular α-Al phase was found in cooling slope sample compared to dendritic in the conventional. • After ECAP uniform Si particles distribution and fine α-Al were observed for cooling slope. • We observed significant improvement in wear resistance of ECAPed sample produced by cooling slope. - Abstract: This work investigated the microstructural evolution of Al–7Si–Mg alloy cast semi-solid using a cooling slope as well as conventional casting followed by equal channel angular pressing (ECAP) in a 120° die. Feed materials were prepared for ECAP by cooling slope casting and by conventional casting. The microstructure of the processed alloys extruded was observed by optical microscope and by transmission electron microscope, and their hardness and wear resistance were evaluated. After ECAP processing, the primary α-Al phase tended to be elongated while the Si particles became fragmented and more nearly globular in shape and uniform in size than in the as-cast sample. The microstructure of the cooling slope-cast ECAPed samples was more homogenous than that of the conventionally cast ECAPed sample. The α-Al phase sub-grains were refined to sub-micrometer sizes for samples cast by both methods after ECAP. The hardness of the cooling slope-cast ECAPed sample was also higher than that of the conventionally cast ECAPed sample. The wear resistance of the alloy improved after cooling slope casting and ECAP processing

die pers as bron oor die geskiedenis van die eerste vrydeidsoorlog

African Journals Online (AJOL)

dood agv wonde wat hy tydens die slag opgedoen het. Dit was vir die Britse volk onaanvaarbaar dat slegs twee Boere gedood is nadat daar tussen. 20 000 en 30 000 rondtes op die Boere afgevuur is. Die pers kon net nie die ware syfers publiseer nie, want dit sou na 'n onwaarheid Iyk. Het die. Britse volk egter die Boere ...

Die partypolitiek en die toekoms van die Afrikaanse volkskultuur

Directory of Open Access Journals (Sweden)

A.P. Treurnicht

1970-03-01

Full Text Available Reeds in 1853 het die Zuid Afrikaan hom soos volg uitgelaat: „Dis ’n dwaling wat ons reeds meermale bestry het dat ons as Britse onderdane verplig sou wees, om die Britse nasionaliteit ons s’n te maak. Die Kolonis van Hollandse oorsprong kan geen Engelsman word nie, en moet ook geen Nederlander wil wees nie. Wanneer hy weet om sy standpunt te waardeer, dan sal hy as verligte kolonis die grondtrekke van die Engelse volkskarakter met dié van die Nederlandse harmonies leer verenig en daardeur word wat hy as Kapenaar moet word.”

die heidelbergse kategismus en die kategesemateriaal van die ned

African Journals Online (AJOL)

subjek, objek, leerstof en die metodiek van die senior kategese. Bloemfontein: Algemene Jeugkommissie Sondagskoolboekhandel. de rAAd oer ned ger kerken in Zuid AfrikA. 1921. De zevende vergadering: handelinge. 1925. De negende vergadering: handelinge. de villierS, d. W. 1957. Die Kategese in die Ned. Geref.

Centrifugal Casting Features/Metallurgical Characterization of Aluminum Alloys

International Nuclear Information System (INIS)

Chirita, G.; Soares, D.; Cruz, D.; Silva, F. S.; Stefanescu, I.

2008-01-01

This paper deals with the study of centrifugal effects on aluminium castings under high G values. Most of the studies in this domain (FGMs obtained by centrifugal casting) deal with functionally graded composites reinforced with a solid phase such as silicon particles or others. However, in this study it will be shown that unreinforced aluminium alloys may be significantly influenced by the centrifugal effect and that functionally graded castings are also obtained. It has been observed that the centrifugal effect may increase in some alloys, depending on the relative position in the castings, the rupture strength by approx. 50%, and rupture strain by about 300%, as compared to the gravity casting technique. The Young's modulus may also increase by about 20%. It has also been reported that in vertical centrifugal castings there are mainly three aspects that affect the components thus obtained, namely: fluid dynamics; vibration (inherent to the system); and centrifugal force. These features have a different effect on the castings depending on the aluminium alloy. In this paper, an analysis of the most important effects of the centrifugal casting process on metallurgical features is conducted. A solidification characterization at several points along the mould will be made in order to have an accurate idea of both the fluid dynamics inside the mould during the casting and the solidification behavior in different parts of the component. These two analyses will be related to the metallurgical properties (phase distribution; SDAS; eutectic silicon content and shape, pores density and shape) along the component and mainly along the direction of the centrifugal pressure. A comparison between castings obtained by both centrifugal casting technique and gravity casting technique is made for reference (gravity casting)

Die invloed van die neo-marxistiese kultuuranalise op die Wêreldraad van Kerke en die Gereformeerde Kerke van Nederland

Directory of Open Access Journals (Sweden)

J. M. Vorster

1979-05-01

Full Text Available Toe die studente dwarsoor die VSA en Europa in die laat sestigerjare ’n plotselinge en radikale verset openbaar het teen die bestaande orde, het hulle die deur geopen vir ’n nuwe mededinger om die hart van die Westerse kultuur. Dit is die nou reeds bekende neo-Marxisme. Sedertdien het hierdie jongeling sy voetspore op vele vlakke van die Westerse kultuur gelaat.

Die regsposisie van die gemolesteerde kind 1

Directory of Open Access Journals (Sweden)

P.J. Schabort

1991-03-01

Full Text Available Hoe reik die reg uit na die seksueel gemolesteerde kind? As na die reg in wye verband gekyk word, sou dit alie wetgewing en alle gemeneregsbeginsels en alle regsprosedures insluit waardeur die Staat poog om molestering te voorkom en die gemolesteerde kind in beskerming te neem. Dit le baie wyd en sou byvoorbeeld die maatreels insluit van die Kindenvet 33 van 1960; die Wet op Egskeiding 70 van 1979; die Wet op Kindersorg 74 van 1983; die Wet op die Status van Kinders 82 van 1987 en die Wet op Bemiddeling in Sekere Egskeidingsaangeleenthede 24 van 1987. Eersdaags sal dit moontlik ook ’n Manifes vir die Regte van Kinders insluit wat vermoedelik geskoei sal wees op die W O se Konvensie vir die Regte van die Kind (1989 w a arv an die RSA tan s nog nie ’n ondertekenaar is nie.

Capillarity theory for the fly-casting mechanism

Science.gov (United States)

Trizac, Emmanuel; Levy, Yaakov; Wolynes, Peter G.

2010-01-01

Biomolecular folding and function are often coupled. During molecular recognition events, one of the binding partners may transiently or partially unfold, allowing more rapid access to a binding site. We describe a simple model for this fly-casting mechanism based on the capillarity approximation and polymer chain statistics. The model shows that fly casting is most effective when the protein unfolding barrier is small and the part of the chain which extends toward the target is relatively rigid. These features are often seen in known examples of fly casting in protein–DNA binding. Simulations of protein–DNA binding based on well-funneled native-topology models with electrostatic forces confirm the trends of the analytical theory. PMID:20133683

Freeze-casting: Fabrication of highly porous and hierarchical ceramic supports for energy applications

Directory of Open Access Journals (Sweden)

Cyril Gaudillere

2016-03-01

The aim of this paper is to give an overview of the freeze-casting ceramic shaping method and to show how its implementation could be useful for several energy applications where key components comprise a porous scaffold. A detailed presentation of the freeze-casting process and of the characteristics of the resulting porous parts is firstly given. The characteristic of freeze-cast parts and the drawbacks of conventional porous scaffolds existing in energy applications are drawn in order to highlight the expected beneficial effect of this new shaping technique as possible substitute to the conventional ones. Finally, a review of the state of the art freeze-cast based energy applications developed up to now and expected to be promising is given to illustrate the large perspectives opened by the implementation of the freeze-casting of ceramics for energy fields. Here we suggest discussing about the feasibility of incorporate freeze-cast porous support in high temperature ceramic-based energy applications.

Geometrical modulus of a casting and its influence on solidification process

Directory of Open Access Journals (Sweden)

F. Havlicek

2011-10-01

Full Text Available Object: The work analyses the importance of the known criterion for evaluating the controlled solidification of castings, so called geometrical modulus defined by N. Chvorinov as the first one. Geometrical modulus influences the solidification process. The modulus has such specificity that during the process of casting formation it is not a constant but its initial value decreases with the solidification progress because the remaining melt volume can decrease faster than its cooling surface.Methodology: The modulus is determined by a simple calculation from the ratio of the casting volume after pouring the metal in the mould to the cooled mould surface. The solidified metal volume and the cooled surface too are changed during solidification. That calculation is much more complicated. Results were checked up experimentally by measuring the temperatures in the cross-section of heavy steel castings during cooling them.Results: The given experimental results have completed the original theoretical calculations by Chvorinov and recent researches done with use of numerical calculations. The contribution explains how the geometrical modulus together with the thermal process in the casting causes the higher solidification rate in the axial part of the casting cross-section and shortening of solidification time. Practical implications: Change of the geometrical modulus negatively affects the casting internal quality. Melt feeding by capillary filtration in the dendritic network in the casting central part decreases and in such a way the shrinkage porosity volume increases. State of stress character in the casting is changed too and it increases.

Fibreglass Total Contact Casting, Removable Cast Walkers, and Irremovable Cast Walkers to Treat Diabetic Neuropathic Foot Ulcers: A Health Technology Assessment

Science.gov (United States)

Costa, Vania; Tu, Hong Anh; Wells, David; Weir, Mark; Holubowich, Corinne; Walter, Melissa

2017-01-01

Background Diabetic neuropathic foot ulcers are a risk factor for lower leg amputation. Many experts recommend offloading with fibreglass total contact casting, removable cast walkers, and irremovable cast walkers as a way to treat these ulcers. Methods We completed a health technology assessment, which included an evaluation of clinical benefits and harms, value for money, and patient preferences for offloading devices. We performed a systematic literature search on August 17, 2016, to identify randomized controlled trials that compared fibreglass total contact casting, removable cast walkers, and irremovable cast walkers with other treatments (offloading or non-offloading) in patients with diabetic neuropathic foot ulcers. We developed a decision-analytic model to assess the cost-effectiveness of fibreglass total contact casting, removable cast walkers, and irremovable cast walkers, and we conducted a 5-year budget impact analysis. Finally, we interviewed people with diabetes who had lived experience with foot ulcers, asking them about the different offloading devices and the factors that influenced their treatment choices. Results We identified 13 randomized controlled trials. The evidence suggests that total contact casting, removable cast walkers, and irremovable cast walkers are beneficial in the treatment of neuropathic, noninfected foot ulcers in patients with diabetes but without severe peripheral arterial disease. Compared to removable cast walkers, ulcer healing was improved with total contact casting (moderate quality evidence; risk difference 0.17 [95% confidence interval 0.00–0.33]) and irremovable cast walkers (low quality evidence; risk difference 0.21 [95% confidence interval 0.01–0.40]). We found no difference in ulcer healing between total contact casting and irremovable cast walkers (low quality evidence; risk difference 0.02 [95% confidence interval −0.11–0.14]). The economic analysis showed that total contact casting and irremovable

Melting, casting, and alpha-phase extrusion of the uranium-2.4 weight percent niobium alloy

International Nuclear Information System (INIS)

Anderson, R.C.; Beck, D.E.; Kollie, T.G.; Zorinsky, E.J.; Jones, J.M.

1981-10-01

The experimental details of the melting, casting, homogenization, and alpha-phase extrusion process used to fabricate the uranium-2.4 wt % niobium alloy into 46-mm-diameter rods is described. Extrusion defects that were detected by an ultrasonic technique were eliminated by proper choice of extrusion parameters; namely, reduction ratio, ram speed, die angle, and billet preheat temperature

Development Program for Natural Aging Aluminum Casting Alloys

Energy Technology Data Exchange (ETDEWEB)

Dr. Geoffrey K. Sigworth

2004-05-14

A number of 7xx aluminum casting alloys are based on the ternary Al-Zn-Mg system. These alloys age naturally to high strength at room temperature. A high temperature solution and aging treatment is not required. Consequently, these alloys have the potential to deliver properties nearly equivalent to conventional A356-T6 (Al-Si-Mg) castings, with a significant cost saving. An energy savings is also possible. In spite of these advantages, the 7xx casting alloys are seldom used, primarily because of their reputation for poor castibility. This paper describes the results obtained in a DOE-funded research study of these alloys, which is part of the DOE-OIT ''Cast Metals Industries of the Future'' Program. Suggestions for possible commercial use are also given.

Die hervertolking van die paradigma in verband met die ...

African Journals Online (AJOL)

Kerkorde van De Mist en die Algemene Reglement van 1816, wat onderskeidelik vir die Kaapse Kerk en die .... Een van die eerstes was Sam Freiherr von Pufendorf (1632-1694) wat in sy werk De habitu religionis ..... Koning was weer aan bewind (vgl Diepenhorst sj:74w; De Visser 1926/1927 lll:202w). 43.1 JD Janssen ...

Die teologiese skool in die P.U.K vir C.H.O.: met die betekenis van die teologiese skool vir die Christelike wetenskap

Directory of Open Access Journals (Sweden)

F. Postma

1944-03-01

Full Text Available Die Teologiese Skool van die Gereformeerde Kerk gedink op 29 November 1944 sy vyf-en-sewentigjarige bestaan.Die Raad en Senaat van die P.U.K. vir C.H.O. wil ook langs hierdie weg die Teologiese Skool van harte gelukwens en die versekering gee dat daar by die outoriteite van die P.U.K. ’n diepgevoelde dankbaarheid heers dat hierdie inrigting sovele jare deur onse God en Vader gedra en gespaar is.

Impact of Simulation Technology on Die and Stamping Business

Science.gov (United States)

Stevens, Mark W.

2005-08-01

Over the last ten years, we have seen an explosion in the use of simulation-based techniques to improve the engineering, construction, and operation of GM production tools. The impact has been as profound as the overall switch to CAD/CAM from the old manual design and construction methods. The changeover to N/C machining from duplicating milling machines brought advances in accuracy and speed to our construction activity. It also brought significant reductions in fitting sculptured surfaces. Changing over to CAD design brought similar advances in accuracy, and today's use of solid modeling has enhanced that accuracy gain while finally leading to the reduction in lead time and cost through the development of parametric techniques. Elimination of paper drawings for die design, along with the process of blueprinting and distribution, provided the savings required to install high capacity computer servers, high-speed data transmission lines and integrated networks. These historic changes in the application of CAE technology in manufacturing engineering paved the way for the implementation of simulation to all aspects of our business. The benefits are being realized now, and the future holds even greater promise as the simulation techniques mature and expand. Every new line of dies is verified prior to casting for interference free operation. Sheet metal forming simulation validates the material flow, eliminating the high costs of physical experimentation dependent on trial and error methods of the past. Integrated forming simulation and die structural analysis and optimization has led to a reduction in die size and weight on the order of 30% or more. The latest techniques in factory simulation enable analysis of automated press lines, including all stamping operations with corresponding automation. This leads to manufacturing lines capable of running at higher levels of throughput, with actual results providing the capability of two or more additional strokes per

Effects of HIP and forging on fracture behaviour in cast iron with spheroidal vanadium carbides dispersed within martensitic-matrix microstructure

International Nuclear Information System (INIS)

Uematsu, Y.; Tokaji, K.; Nishigaki, K.; Okajima, D.; Ogasawara, M.

2010-01-01

The cast iron with spheroidal vanadium carbides dispersed within martensitic-matrix microstructure was developed as a die material due to its high hardness. In order to achieve high performances of dies, not only the hardness but also the mechanical properties such as fracture toughness and fatigue crack propagation (FCP) resistance should be improved. In this paper, hot isostatic pressing (HIP) or forging was applied to the cast iron to improve mechanical properties, and the fracture behaviour, such as flexural strength, fracture toughness and FCP, was studied. The average flexural strength was reduced by forging because of the enhanced notch sensitivity due to the increase in the hardness. The fracture toughness was not affected by HIP nor forging while its scatter was significantly reduced by both post-treatments. The intrinsic FCP resistance taking account of crack closure was the same regardless of the application of HIP or forging, indicating that a slight change in the microstructure resulting from both treatments and the presence of casting defects exerted little influence on FCP behaviour. It could be concluded that both HIP and forging could improve the hardness of the material, while fracture toughness and FCP resistance were maintained.

[August Schummer (1902-1977): breaking ground for new corrosion casting anatomy].

Science.gov (United States)

Vollmerhaus, B

2002-12-01

About 70 years ago, when the so-called polymeric science succeeded in producing synthetic materials and making it available to industrial manufacturing, August Schummer intuitively recognized and reconnoitred the use of these new materials for corrosion casting anatomy. Through the employment of this method, which was named after him, an epoch-making step was achieved in the anatomy of corrosion casting. In the year that followed there has been a very successful progress in the exploration of blood vessels right through into the capillaries of the organs. On the occasion of the 100th birthday of August Schummer (born 13th of December 1902 in Sălişte near Hermannstadt, died 1st of March 1977 in Giessen), former Professor of Veterinary Anatomy at the Universität Giessen, we commemorate the life and work of this exceptionally talented and passionate anatomist.

Hot Embossing of Zr-Based Bulk Metallic Glass Micropart Using Stacked Silicon Dies

Directory of Open Access Journals (Sweden)

Zhijing Zhu

2015-01-01

Full Text Available We demonstrated hot embossing of Zr65Cu17.5Ni10Al7.5 bulk metallic glass micropart using stacked silicon dies. Finite element simulation was carried out, suggesting that it could reduce the stress below 400 MPa in the silicon dies and enhance the durability of the brittle silicon dies when using varying load mode (100 N for 60 s and then 400 N for 60 s compared with using constant load mode (200 N for 120 s. A micropart with good appearance was fabricated under the varying load, and no silicon die failure was observed, in agreement with the simulation. The amorphous state of the micropart was confirmed by differential scanning calorimeter and X-ray diffraction, and the nanohardness and Young’s modulus were validated close to those of the as-cast BMG rods by nanoindentation tests. The results proved that it was feasible to adopt the varying load mode to fabricate three-dimensional Zr-based bulk metallic glass microparts by hot embossing process.

An overview of high thermal conductive hot press forming die material development

Directory of Open Access Journals (Sweden)

A.R. Zulhishamuddin

2015-12-01

Full Text Available Most of the automotive industries are using high strength steel components, which are produced via hot press forming process. This process requires die material with high thermal conductivity that increases cooling rate during simultaneous quenching and forming stage. Due to the benefit of high quenching rate, thermal conductive die materials were produced by adding carbide former elements. This paper presents an overview of the modification of alloying elements in tool steel for high thermal conductivity properties by transition metal elements addition. Different types of manufacturing processes involved in producing high thermal conductive materials were discussed. Methods reported were powder metallurgy hot press, direct metal deposition, selective laser melting, direct metal laser sintering and spray forming. Elements likes manganese, nickel, molybdenum, tungsten and chromium were proven to increase thermal conductivity properties. Thermal conductivity properties resulted from carbide network presence in the steel microstructure. To develop feasible and low cost hot press forming die material, casting of Fe-based alloy with carbide former composition can be an option. Current thermal conductivity properties of hot press forming die material range between 25 and 66 W/m.K. The wide range of thermal conductivity varies the mechanical properties of the resulting components and lifetime of HPF dies.

The Effect of Casting Ring Liner Length and Prewetting on the Marginal Adaptation and Dimensional Accuracy of Full Crown Castings.

Science.gov (United States)

Haralur, Satheesh B; Hamdi, Osama A; Al-Shahrani, Abdulaziz A; Alhasaniah, Sultan

2017-01-01

To evaluate the effect of varying cellulose casting ring liner length and its prewetting on the marginal adaptation and dimensional accuracy of full veneer metal castings. The master die was milled in stainless steel to fabricate the wax pattern. Sixty wax patterns were fabricated with a uniform thickness of 1.5 mm at an occlusal surface and 1 mm axial surface, cervical width at 13.5 mm, and 10 mm cuspal height. The samples were divided into six groups ( n = 10). Groups I and II samples had the full-length cellulose prewet and dry ring liner, respectively. The groups III and IV had 2 mm short prewet and dry cellulose ring liner, respectively, whereas groups V and VI were invested in 6 mm short ring liner. The wax patterns were immediately invested in phosphate bonded investment, and casting procedure was completed with nickel-chrome alloy. The castings were cleaned and mean score of measurements at four reference points for marginal adaption, casting height, and cervical width was calculated. The marginal adaption was calculated with Imaje J software, whereas the casting height and cervical width was determined using a digital scale. The data was subjected to one-way analysis of varaince and Tukey post hoc statistical analysis with Statistical Package for the Social Sciences version 20 software. The group II had the best marginal adaption with a gap of 63.786 μm followed by group I (65.185 μm), group IV (87.740 μm), and group III (101.455 μm). A large marginal gap was observed in group V at 188.871 μm. Cuspal height was more accurate with group V (10.428 mm), group VI (10.421 mm), and group II (10.488 mm). The cervical width was approximately similar in group I, group III, and group V. Statistically significant difference was observed in Tukey post hoc analysis between group V and group VI with all the other groups with regards to marginal adaptation. The dry cellulose ring liners provided better marginal adaptation in comparison to prewet cellulose ring

Mechanical properties of ductile cast iron and cast steel for intermediate level waste transport containers

International Nuclear Information System (INIS)

Gray, I.L.S.; Sievwright, R.W.T.; Egid, B.; Ajayi, F.; Donelan, P.

1994-01-01

UK Nirex Ltd is developing Type B re-usable shielded transport containers (RSTCs) in a range of shielding thicknesses to transport intermediate level radioactive waste (ILW) to a deep repository. The designs are of an essentially monolithic construction and rely principally on the plastic flow of their material to absorb the energies involved in impact events. Nirex has investigated the feasibility of manufacturing the RSTCs from ductile cast iron (DCI) or cast steel instead of from forgings, since this would bring advantages of reduced manufacturing time and costs. However, cast materials are perceived to lack toughness and ductility and it is necessary to show that sufficient fracture toughness can be obtained to preclude brittle failure modes, particularly at low temperatures. The mechanical testing carried out as part of that programme is described. It shows how the measured properties have been used to demonstrate avoidance of brittle fracture and provide input to computer modelling of the drop tests. (author)

die sinodale verband van die nederduitse gereformeerde kerk in die

African Journals Online (AJOL)

Liezel

Strauss. Die sinodale verband van die Nederduitse Gereformeerde Kerk. 122 die Vrystaatse Sinode anti-veranderingsgesind of eerder gesond-behoudend of gereformeerd-gematig? Veral as dit .... howe) in moeilike omstandighede gebring is (NG Kerk in die OVS 1865-1912:5). In 'n brief op 8 Augustus 1864 ontken Ds.

Die kerkregtelike posisie van die ouderling en diaken in die ...

African Journals Online (AJOL)

... drie dekades die Kerkreg gevestig as 'n selfstandige vak in die teologiese curriculum, maar ook 'n baie groot rol gespeel daarin dat die beginsels van die kerk like reg beter begryp word. Naas sy wetenskaplike bydrae word met eweveel genoegdoening gedink aan sy bcsondere persoonlikheid, sy werkvermoe, sy humor-.

Control of cast iron and casts manufacturing by Inmold method

Directory of Open Access Journals (Sweden)

S. Pietrowski

2009-07-01

Full Text Available In this paper the usability of cast iron spheroidizing process in mould control by ATD method as well as by ultrasonic method were presented. Structure of instrumentation needed for control form performance of cast iron spheroidizing by Inmold method was illustrated. Author, pointed out that amount of magnesium master alloy should obtain 0,8 ÷ 1,0% of mass in form at all. Such quantity of preliminary alloy assure of obtain of nodular graphite in cast iron. In consequence of this, is reduce the cast iron liquidus temperature and decrease of recalescence temperature of graphite-eutectic crystallization in compare with initial cast iron. Control of casts can be carried out by ultrasonic method. In plain cast iron, ferritic-pearlitic microstructure is obtaining. Additives of 1,5% Cu ensure pearlitic structure.

The casting of western sculpture during the XIXth century: sand casting versus lost wax casting

NARCIS (Netherlands)

Beentjes, T.P.C.

2014-01-01

This paper will discuss research into bronze casting techniques as practiced during the XIXth and early XXth century. Both natural sand casting (fonte au sable naturel) and lost wax casting (fonte à la cire perdue) were employed during this period and sometimes rivalled for commissions. Before the

Evaluation of the new TAMZ titanium alloy for dental cast application.

Science.gov (United States)

Zhang, Y M; Guo, T W; Li, Z C

2000-12-01

To reveal the potential of the new titanium alloy as dental prosthodontic materials. Dental castings of TAMZ alloy were investigated in the casting machine specially designed for titanium. A mesh pattern was used to count the castability value. The mechanical properties were measured by means of a universal testing machine. Optical micrography was done on the exposed cross-section of TAMZ alloy casting. From the surface to the inner part the Knoop hardness in reacted layer of TAMZ alloy casting was measured. The structure and elemental analyses of the reacted layer were made by SEM and element line scanning observation. The castability value (Cv = 98%) and the tensile test (sigma b = 850 Mpa, sigma 0.2 = 575 Mpa, delta = 7.33%) data were collected. The castings microstructure showed main alpha phase and small beta phase. Knoop hardness in the surface reacted layer was greater than that in the inner part. From the SEM and element line scanning observation, there are three different layers in the surface reacted layer of the TAMZ alloy castings, and higher level of element of O, Al, Si and Zr were found in the reacted layer while the Si permeated deeper than others. TAMZ alloy can be accepted as a material for dental alloy in prosthodontics.

Die gebruik van parallelplaatreologie vir die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat

Directory of Open Access Journals (Sweden)

O. C. Vorster

2005-09-01

Full Text Available Die bepaling van die intrinsieke viskositeit van poli-etileentereftalaat word bemoeilik deur die feit dat daar tans slegs twee metodes in gebruik is. In die eerste metode word die bepaling deur middel van oplossingsviskometrie gedoen, maar die toksisiteit van die oplosmiddel, asook die tydperk wat dit neem om die bepaling te doen, is ’n probleem. Die tweede metode word beperk deur die kompleksiteit en beskikbaarheid van die apparatuur in Suid-Afrika. In hierdie studie word ’n alternatiewe metode, gebaseer op parallelplaatreologie, voorgestel wat albei hierdie probleme oorkom en die resultate sodoende verkry, word vergelyk met dié wat met bestaande metodes verkry is.

Cast Ductile Iron 155mm M804 Bodies

Science.gov (United States)

1990-07-12

for the final delivery. The balance of the parts were returned to Wagner Castings for analysis, scrap, or de-militarization. The radiographic...as possible to avoid pre-cure. Mixing/ mulling time should be consistent with the system " worklife " or poor composite properties will result. Tensile...Burn-in on castings is caused by poor sand density, poor mixing, out of balance mix or improper drying of the wash. Long set times are an indication

Linear dimensional changes in plaster die models using different elastomeric materials

Directory of Open Access Journals (Sweden)

Jefferson Ricardo Pereira

2010-09-01

Full Text Available Dental impression is an important step in the preparation of prostheses since it provides the reproduction of anatomic and surface details of teeth and adjacent structures. The objective of this study was to evaluate the linear dimensional alterations in gypsum dies obtained with different elastomeric materials, using a resin coping impression technique with individual shells. A master cast made of stainless steel with fixed prosthesis characteristics with two prepared abutment teeth was used to obtain the impressions. References points (A, B, C, D, E and F were recorded on the occlusal and buccal surfaces of abutments to register the distances. The impressions were obtained using the following materials: polyether, mercaptan-polysulfide, addition silicone, and condensation silicone. The transfer impressions were made with custom trays and an irreversible hydrocolloid material and were poured with type IV gypsum. The distances between identified points in gypsum dies were measured using an optical microscope and the results were statistically analyzed by ANOVA (p < 0.05 and Tukey's test. The mean of the distances were registered as follows: addition silicone (AB = 13.6 µm, CD=15.0 µm, EF = 14.6 µm, GH=15.2 µm, mercaptan-polysulfide (AB = 36.0 µm, CD = 36.0 µm, EF = 39.6 µm, GH = 40.6 µm, polyether (AB = 35.2 µm, CD = 35.6 µm, EF = 39.4 µm, GH = 41.4 µm and condensation silicone (AB = 69.2 µm, CD = 71.0 µm, EF = 80.6 µm, GH = 81.2 µm. All of the measurements found in gypsum dies were compared to those of a master cast. The results demonstrated that the addition silicone provides the best stability of the compounds tested, followed by polyether, polysulfide and condensation silicone. No statistical differences were obtained between polyether and mercaptan-polysulfide materials.

Die ontwikkeling van die bestuursmotiveringsvraelys (BMV

Directory of Open Access Journals (Sweden)

A. S. Engelbrecht

1991-06-01

Full Text Available The development of the Managerial Motivation Questionnaire (MMQ: Several criticisms of the psychometric suitability of existing measures of managerial motivation are reported in the literature. This study aimed at developing a new psychometrically sound instrument, the Managerial Motivation Questionnaire (MMQ. This was done on the basis of a comprehensive study of the literature on managerial motivation and the role-motivation theory. The preliminary MMQ was systematically shortened and refined until the final MMQ of 98 items was composed. This was based on social desirability and semantic appraisal, item analysis and factor analysis of the questionnaire. The results indicate that it was possible to develop a final MMQ that was relatively free of social desirability. It further demonstrated satsifactory internal consistencies on two samples (a = 0/90, N = 360; a = 0/91, N = 535, where all subscale items were found to be relatively pure measures of the isolated factors. Although some evidence was found providing support for the reliability of the MMQ, a need for further research on the construct validity of managerial motivation still exists. Opsomming In die literatuur word verskeie punte van kritiek teen die psigometriese geskiktheid van bestaande meetinstrumente van bestuursmotivering gerapporteer. Die doelstelling van hierdie studie was dus om aan die hand van die konseptuele omiyning van bestuursmotivering, en die rolmotiveringsteorie as algemene verwysingsraamwerk, 'n nuwe psigometries aanvaarbare meetinstrument, die Bestuursmotiveringsvraelys (BMV, te ontwikkel. Op grond van sosiale wenslikheids- en semantiese beoordeling, itemontleding en faktorontleding van die voorlopige BMV is die vraelys stelselmatig verkort en verfyn totdat die finale BMV van 98 items saamgestel is. Die resultate dui daarop dat hierdie studie wel daarin geslaag het om 'n finale BMV te ontwikkel wat relatief vry van sosiale wenslikheid is, bevredigende interne

低融点合金を用いた卓上射出鋳造装置の成形性向上に関する研究

OpenAIRE

松本, 隼人; 田中, 裕一; 宮本, 憲隆

2012-01-01

The purpose of this research is improving in the products by making the desktop die casting machine using a low melting point alloy and observing phenomenon in the transparent mold made of acrylic resin. Desktop die casting machine is minimum structure, which is composed of an injection part, a mold part, an actuator and a chamber for injection molten metal. The molten metal is injected into the mold with the actuator, and its phenomenon in the mold is observed by using a high speed camera. I...

Cap casting and enveloped casting techniques for Zr55Cu30Ni5Al10 glassy alloy rod with 32 mm in diameter

International Nuclear Information System (INIS)

Yokoyama, Yoshihiko; Inoue, Akihisa; Mund, Enrico; Schultz, Ludwig

2009-01-01

In order to produce centimetre-sized bulk glassy alloys (BMGs), various cast techniques have been developed. We succeed in the development of cap casting and enveloped casting technique to accomplish the fabrication of centimetre sized BMGs. The former has an advantage to increase cooling rate and the later has an advantage to joint another materials instead of welding. This paper presents the production of a glassy Zr 55 Cu 30 Ni 5 Al 10 alloy rod with a diameter of 32 mm and joined glassy Zr 55 Cu 30 Ni 5 Al 10 alloy parts with another materials for industrial applications.

Experimental analysis of flow of ductile cast iron in stream lined gating systems

DEFF Research Database (Denmark)

Skov-Hansen, Søren Peter; Tiedje, Niels Skat

2008-01-01

Streamlined gating systems have been developed for production of high integrity ductile cast iron parts. Flow of ductile cast iron in streamlined gating systems was studied in glass fronted sand moulds where flow in the gating system and casting was recorded by a digital video camera. These results...... show how the quality of pouring, design of ingates, design of bends and flow over cores influence melt flow and act to determine the quality of the castings....

Wear of Shaped Surfaces of PVD Coated Dies for Clinching

Directory of Open Access Journals (Sweden)

Miroslav Džupon

2017-11-01

Full Text Available A clinching method that uses a simple toolset consisting of a punch and a die, is utilized for joining lightweight materials. This paper is aimed at investigating the wear of the die cavity of a clinching tool. A clinching tool with a specially shaped cavity was used for joining thin hot-dip galvanized steel sheets. Various types of physical vapour deposition (PVD coatings such as ZrN, CrN and TiCN were deposited on the shaped surface of the die using Lateral Rotating Arc-Cathodes technology. Hot-dip galvanized steel sheets were used for testing the clinching tool. The material properties of PVD coatings that were deposited on the shaped part of the clinching die were evaluated. Finite Element Analysis was used to localize the area of the shaped part of the die and the part of surface area of the cylindrical die cavity of ϕ 5.0 mm, in which high contact pressure values were predicted. The prediction of the start of the wear cycle was verified experimentally by the clinching of 300 samples of hot-dip galvanized steel sheets. Unlike the CrN and ZrN coatings, the TiCN coating remained intact on the entire surface of the die.

Microstructure and property evaluation of high-pressure die-cast Mg–La–rare earth (Nd, Y or Gd) alloys

International Nuclear Information System (INIS)

Gavras, Serge; Easton, Mark A.; Gibson, Mark A.; Zhu, Suming; Nie, Jian-Feng

2014-01-01

Highlights: • Different rare earth elements have remarkably different effects on Mg castability. • For the addition of each RE element, the alloy castability follows a unique pattern. • The effects of RE elements on the castability can be modelled. - Abstract: Microstructure, castability and tensile properties were investigated in high-pressure die-cast Mg–La–Nd, Mg–La–Y and Mg–La–Gd alloy series, with a constant La concentration at approximately 2.5 wt.% and the concentrations of Nd, Y or Gd were varied. All three alloy series had a dendritic microstructure with a Mg–La-rich eutectic with increasing Nd, Y or Gd content and containing a Mg 12 RE intermetallic phase. The morphology of the eutectic at ternary alloying additions of equal to or less than 1.0 wt.% was lamellar but became increasingly divorced at higher ternary concentrations. This was however more obvious in Mg–La–Y and Mg–La–Gd than Mg–La–Nd alloys. The hot tearing susceptibility in all three alloy series increased markedly with even micro-alloying additions of Nd, Y or Gd, and began to decrease again in alloys with more than 0.5 wt.% Y or 1.0 wt.% Gd, but did not decrease significantly for Mg–La–Nd. A model using the temperature–fraction solid curves as input parameters was used to estimate hot tearing susceptibility for Mg–La–Nd alloys. Tensile testing at room temperature showed that Mg–La–Nd alloy series had higher 0.2% proof stress and lower elongation to failure than either the Mg–La–Y or the Mg–La–Gd alloy series for Nd concentrations greater than 1 wt.% due to a greater effectiveness of grain boundary reinforcement

Die uitbouing van die Bybelse kanon in antieke Judaïsme en die ...

African Journals Online (AJOL)

31 Jul 2015 ... die oer-Christelike boodskap tot by sy Ou Testamentiese wortels, die geskrifte van Israel wat cum grano salis die 'Bybel' van die oer-Christendom geword het en die blywende verwysingspunt van die Christelike boodskap is. Erkenning. Hierdie artikel is vertaal na Afrikaans deur Prof. Jan G. van der Watt.

New Approaches to Aluminum Integral Foam Production with Casting Methods

Directory of Open Access Journals (Sweden)

Ahmet Güner

2015-08-01

Full Text Available Integral foam has been used in the production of polymer materials for a long time. Metal integral foam casting systems are obtained by transferring and adapting polymer injection technology. Metal integral foam produced by casting has a solid skin at the surface and a foam core. Producing near-net shape reduces production expenses. Insurance companies nowadays want the automotive industry to use metallic foam parts because of their higher impact energy absorption properties. In this paper, manufacturing processes of aluminum integral foam with casting methods will be discussed.

Wide Strip Casting Technology of Magnesium Alloys

Science.gov (United States)

Park, W.-J.; Kim, J. J.; Kim, I. J.; Choo, D.

Extensive investigations relating to the production of high performance and low cost magnesium sheet by strip casting have been performed for the application to automotive parts and electronic devices. Research on magnesium sheet production technology started in 2004 by Research Institute of Industrial Science and Technology (RIST) with support of Pohang Iron and Steel Company (POSCO). POSCO has completed the world's first plant to manufacture magnesium coil. Another big project in order to develop wide strip casting technology for the automotive applications of magnesium sheets was started in succession.

Travelling Through Caste

OpenAIRE

Kumar, Raj

2016-01-01

With its peculiar caste system, India is considered the most stratified of all known societies in human history. This system is ‘peculiar’ as it divides human beings into higher and lower castes and this division is backed by certain religious sanctions based on the sociological concepts of ‘purity’ and ‘pollution’. While the higher caste is associated with ‘purity’, the lower caste is associated with ‘pollution’. The people of the lower castes are not allowed to undertake religious journeys ...

Improved life of die casting dies of H13 steel by attaining improved mechanical properties and distortion control during heat treatment. Year 1 report, October 1994--September 1995

Energy Technology Data Exchange (ETDEWEB)

Wallace, J.F.; Schwam, D. [Case Western Reserve Univ., Cleveland, OH (United States)

1995-03-01

Optimum heat treatment of dies (quenching) is critical in ensuring satisfactory service performance: rapid cooling rates increase the thermal fatigue/heat checking resistance of the steel, although very fast cooling rates can also lead to distortion and lower fracture toughness, increasing the danger of catastrophic fracture. Goal of this project is to increase die life by using fast enough quenching rates (> 30 F/min ave cooling rate from 1750 to 550 F, 1/2 in. below working surfaces) to obtain good toughness and fatigue resistance in Premium grade H-13 steel dies. An iterative approach of computer modeling validated by experiment was taken. Cooling curves during gas quenching of H-13 blocks and die shapes were measured under 2, 5, and 7.5 bar N2 and 4 bar Ar. Resulting dimensional changes and residual stresses were determined. To facilitate the computer modeling work, a database of H-13 mechanical and physical properties was compiled. Finite element analysis of the heat treated shapes was conducted. Good fit of modeled vs measured quenched rates was demonstrated for simple die shapes. The models predict well the phase transformation products from the quench. There is good fit between predicted and measured distortion contours; however magnitude of predicted distortion and residual stresses does not match well the measured values. Further fine tuning of the model is required.

Die verband tussen die sielkundige kontrak en organisasieverbondenheid

Directory of Open Access Journals (Sweden)

K. J. Stanz

1999-06-01

Full Text Available The relationship between the psychological contract and organisational commitment. The aim of this study is to design a measuring instrument with acceptable metric characteristics for the strength of the psychological contract within the South African context, and to determine empirically the relation between the strength of the psychological contract and organisational commitment. The Dhammanungune Model served as foundation for the design of the Strength of the Psychological Contract Questionnaire which consists of two scales namely, a needs expectation scale and a needs fulfilment expectation scale. The items of each scale have been formulated in the manner that ensures that the respondent reacts consecutively to two instructions namely, (a the level of the expectation and (b the importance of the expectation. This questionnaire was administered together with the Organisational Commitment Questionnaire to two population groups within the military environment. The Pearson Product Moment Correlation was calculated between the strength of the psychological contract and organisational commitment and the significance of the correlations was evaluated. Opsomming Die doel van die studie is om 'n meetinstrument met aanvaarbare metriese eienskappe vir die sterkte van die sielkundige kontrak vir Suid-Afrikaanse omstandighede te ontwerp en om empirics die verband tussen die sterkte van die sielkundige kontrak en organisasieverbondenheid te bepaal. Die sterkte van die sielkundige kontrak vraelys is op grond van die Dhammanungune-model ontwerp en het uit twee skale naamlik, die behoefteverwagting- en vervullingsverwagtingskale bestaan. Items vir eike skaal is sodanig geformuleer dat die respondent agteropeenvolgens op twee instruksies naamlik (a die vlak van die verwagting en (b die belangrikheid van die verwagting moet reageer. Die vraelys is saam met die organisasieverbondenheidsvraelys op twee populasies uit 'n militere omgewing toegepas. Die Pearson

DIE ROL VAN DIE TAALWETENSKAP IN DIE ONTWIKKELING VAN ...

African Journals Online (AJOL)

aanslag op die sogenaamde "Intentional Fallacy", heelwat verder. n. Mens sou hier eintlik ook op die invloed van Lacan se toepassing van. De Sacs sure op Freud moet wys, en op Macherey se Theory of Literary. Production. Barthes is naamlik besig om repressie teen te werk, en die teks as produksieproses in stede van ...

Caste and power

DEFF Research Database (Denmark)

Roy, Dayabati

2011-01-01

This paper explores the institution of caste and its operation in a micro-level village setting of West Bengal, an Indian state, where state politics at grass roots level is vibrant with functioning local self-government and entrenched political parties. This ethnographic study reveals that caste...... relations and caste identities have overarching dimensions in the day-to-day politics of the study villages. Though caste almost ceases to operate in relation to strict religious strictures, under economic compulsion the division of labour largely coincides with caste division. In the cultural......–ideological field, the concept of caste-hierarchy seems to continue as an influencing factor, even in the operation of leftist politics....

Improved ceramic slip casting technique. [application to aircraft model fabrication

Science.gov (United States)

Buck, Gregory M. (Inventor); Vasquez, Peter (Inventor)

1993-01-01

A primary concern in modern fluid dynamics research is the experimental verification of computational aerothermodynamic codes. This research requires high precision and detail in the test model employed. Ceramic materials are used for these models because of their low heat conductivity and their survivability at high temperatures. To fabricate such models, slip casting techniques were developed to provide net-form, precision casting capability for high-purity ceramic materials in aqueous solutions. In previous slip casting techniques, block, or flask molds made of plaster-of-paris were used to draw liquid from the slip material. Upon setting, parts were removed from the flask mold and cured in a kiln at high temperatures. Casting detail was usually limited with this technique -- detailed parts were frequently damaged upon separation from the flask mold, as the molded parts are extremely delicate in the uncured state, and the flask mold is inflexible. Ceramic surfaces were also marred by 'parting lines' caused by mold separation. This adversely affected the aerodynamic surface quality of the model as well. (Parting lines are invariably necessary on or near the leading edges of wings, nosetips, and fins for mold separation. These areas are also critical for flow boundary layer control.) Parting agents used in the casting process also affected surface quality. These agents eventually soaked into the mold, the model, or flaked off when releasing the case model. Different materials were tried, such as oils, paraffin, and even an algae. The algae released best, but some of it remained on the model and imparted an uneven texture and discoloration on the model surface when cured. According to the present invention, a wax pattern for a shell mold is provided, and an aqueous mixture of a calcium sulfate-bonded investment material is applied as a coating to the wax pattern. The coated wax pattern is then dried, followed by curing to vaporize the wax pattern and leave a shell

Die belangrikste kenmerk van die diereproduksie- bedrywe oor die ...

African Journals Online (AJOL)

digdhede teen 1980 uit 'n kudde van 30 rnilj.skape ge- produseer moet word. Tweedens sal die faktore ... die Republiek van Suid-Mrika teen 1980 in totaal 28 milj. sal wees. Indien die produsente dit as 'n ..... Appendix Table 4 in Digestive Physiology and nutrition of ruminants Vol. 3 Ed. and Publ. D.C. Church, Oregon State ...

Genetic evidence on the origins of Indian caste populations.

Science.gov (United States)

Bamshad, M; Kivisild, T; Watkins, W S; Dixon, M E; Ricker, C E; Rao, B B; Naidu, J M; Prasad, B V; Reddy, P G; Rasanayagam, A; Papiha, S S; Villems, R; Redd, A J; Hammer, M F; Nguyen, S V; Carroll, M L; Batzer, M A; Jorde, L B

2001-06-01

The origins and affinities of the approximately 1 billion people living on the subcontinent of India have long been contested. This is owing, in part, to the many different waves of immigrants that have influenced the genetic structure of India. In the most recent of these waves, Indo-European-speaking people from West Eurasia entered India from the Northwest and diffused throughout the subcontinent. They purportedly admixed with or displaced indigenous Dravidic-speaking populations. Subsequently they may have established the Hindu caste system and placed themselves primarily in castes of higher rank. To explore the impact of West Eurasians on contemporary Indian caste populations, we compared mtDNA (400 bp of hypervariable region 1 and 14 restriction site polymorphisms) and Y-chromosome (20 biallelic polymorphisms and 5 short tandem repeats) variation in approximately 265 males from eight castes of different rank to approximately 750 Africans, Asians, Europeans, and other Indians. For maternally inherited mtDNA, each caste is most similar to Asians. However, 20%-30% of Indian mtDNA haplotypes belong to West Eurasian haplogroups, and the frequency of these haplotypes is proportional to caste rank, the highest frequency of West Eurasian haplotypes being found in the upper castes. In contrast, for paternally inherited Y-chromosome variation each caste is more similar to Europeans than to Asians. Moreover, the affinity to Europeans is proportionate to caste rank, the upper castes being most similar to Europeans, particularly East Europeans. These findings are consistent with greater West Eurasian male admixture with castes of higher rank. Nevertheless, the mitochondrial genome and the Y chromosome each represents only a single haploid locus and is more susceptible to large stochastic variation, bottlenecks, and selective sweeps. Thus, to increase the power of our analysis, we assayed 40 independent, biparentally inherited autosomal loci (1 LINE-1 and 39 Alu elements

Temperature profiles from XBT casts from the OLEANDER as part of the Marine Resources Monitoring, Assessment and Prediction (MARMAP) project from 1982-06-11 (NODC Accession 8200127)

Data.gov (United States)

National Oceanic and Atmospheric Administration, Department of Commerce — Temperature profiles were collected from XBT casts from the OLEANDER from 11 June 1982. Data were collected by the National Marine Fisheries Service (NMFS) as part...

Technological Aspects of Low-Alloyed Cast Steel Massive Casting Manufacturing

Directory of Open Access Journals (Sweden)

Szajnara J.

2013-12-01

Full Text Available In the paper authors have undertaken the attempt of explaining the causes of cracks net occurrence on a massive 3-ton cast steel casting with complex geometry. Material used for casting manufacturing was the low-alloyed cast steel with increased wear resistance modified with vanadium and titanium. The studies included the primary and secondary crystallization analysis with use of TDA and the qualitative and quantitative analysis of non-metallic inclusions.

A new casting defect healing technology

Energy Technology Data Exchange (ETDEWEB)

Hodge, E.S.; Reddoch, T.W. [ForMat Industries, Inc., Knoxville, TN (United States); Viswanathan, S. [Oak Ridge National Lab., TN (United States)

1997-01-01

A new technology is presented for healing of defects in 356 aluminium alloys that provides economic upgrading of these cast alloys. It uses pneumatic isostatic forging (PIF) to produce high quality Al alloys products with enhanced mechanical properties uniform throughout the part, allowing higher design allowables and increased usage of Al alloy castings. The fundamental mechanism underlying PIF is a single mode plastic deformation process that uses isostatic application of pressures for 10-30 seconds at temperature. The process can be integrated in-line with other production operations, i.e., using the latent heat from the previous casting step. Results of applying the PIF process indicate lower cost and significant improvement in mechanical properties that rival and often exceed corresponding properties of other technologies like hot isostatic pressing and related processes. This process offers many advantages that are described in this paper in addition to presenting case histories of property enhancement by PIF and the mechanism responsible for property enhancement.

Maintaining Low Voiding Solder Die Attach for Power Die While Minimizing Die Tilt

Energy Technology Data Exchange (ETDEWEB)

Hamm, Randy; Peterson, Kenneth A.

2015-10-01

This paper addresses work to minimize voiding and die tilt in solder attachment of a large power die, measuring 9.0 mm X 6.5 mm X 0.1 mm (0.354” x 0.256” x 0.004”), to a heat spreader. As demands for larger high power die continue, minimizing voiding and die tilt is of interest for improved die functionality, yield, manufacturability, and reliability. High-power die generate considerable heat, which is important to dissipate effectively through control of voiding under high thermal load areas of the die while maintaining a consistent bondline (minimizing die tilt). Voiding was measured using acoustic imaging and die tilt was measured using two different optical measurement systems. 80Au-20Sn solder reflow was achieved using a batch vacuum solder system with optimized fixturing. Minimizing die tilt proved to be the more difficult of the two product requirements to meet. Process development variables included tooling, weight and solder preform thickness.

Manufacture of plastic parts by radiation molding

International Nuclear Information System (INIS)

Leszyk, G.M.; Morrison, E.D.; Williams, R.F. Jr.

1977-01-01

Thin plastic parts which can have precise tolerances and can be of complex shape are prepared by casting a viscous radiation-curable composition onto a support, such as a moving web of polymeric material, in the shape of the desired part and then irradiating, for example with ultraviolet radiation or high energy electrons, to cause curing of the composition to a solid plastic. The radiation-curable composition is formulated with viscosity and flow characteristics it to be cast in the exact shape of the part desired yet retain this shape during curing while supported only by the surface on which it has been cast. Plastic parts made by this method can be formed entirely of the radiation-curable composition by casting onto a web having a release surface from which the part can be stripped subsequent to curing or can be formed partially from a web material and partially from the radiation-curable composition by casting onto a web to which the composition will bond and subsequently cutting the web into discrete portions which include the cured composition

Die brein soos beskou deur die Grieke en Romeine

Directory of Open Access Journals (Sweden)

Francois P. Retief

2015-02-01

Full Text Available In Ou Egipte is mummifikasie met uitgebreide reseksie of uitsnyding van organe geassosieer, maar geen kennis is geneem van die morfologie van die brein nie. Griekse skrywers van die sesde en vyfde eeue v.C. het die brein aanvanklik gesien as die setel van intelligensie, die orgaan van sensoriese waarneming en gedeeltelik die oorsprong van sperma. Pneuma het ’n belangrike rol in breinfunksie gespeel. Hippokrates was die eerste om die brein te beskryf as ’n dubbele orgaan, wat met harsingvlies (meninges bedek, funksioneel van pneuma afhanklik en vertolker van begrip is. Tydgenote soos Plato, Aristoteles en Diokles het tot die beskrywing bygedra, maar laasgenoemde twee het beweer dat die hart die middelpunt van intelligensie is en nie die brein nie. Gedurende die laaste helfte van die vierde eeu v.C. is disseksie van die menslike liggaam tydelik aan die mediese skool van Alexandrië toegelaat en het dit tot merkwaardige vooruitgang in die begrip van die menslike anatomie en fisiologie gelei. Herofilus en Erasistratus het uitstekende beskrywings van die struktuur en funksie van die brein gegee wat eers in die tweede eeu n.C. deur Galenus geëwenaar is.

9 CFR 325.20 - Transportation and other transactions concerning dead, dying, disabled, or diseased livestock...

Science.gov (United States)

2010-01-01

... concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of livestock that died... other transactions concerning dead, dying, disabled, or diseased livestock, and parts of carcasses of livestock that died otherwise than by slaughter. No person engaged in the business of buying, selling, or...

Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

International Nuclear Information System (INIS)

Kwon, Yong Chul; Kang, Jong Hun; Kim, Sang Sik

2016-01-01

The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts

Study on Manufacturing Process of Hollow Main Shaft by Open Die Forging

Energy Technology Data Exchange (ETDEWEB)

Kwon, Yong Chul [Gyeongnam Technopark, Changwon (Korea, Republic of); Kang, Jong Hun [Jungwon Univ., Goisan (Korea, Republic of); Kim, Sang Sik [Gyeongsang Natiional Univ., Jinju (Korea, Republic of)

2016-02-15

The main shaft is one of the key components connecting the rotor hub and gear box of a wind power generator. Typically, main shafts are manufactured by open die forging method. However, the main shaft for large MW class wind generators is designed to be hollow in order to reduce the weight. Additionally, the main shafts are manufactured by a casting process. This study aims to develop a manufacturing process for hollow main shafts by the open die forging method. The design of a forging process for a solid main shaft and hollow shaft was prepared by an open die forging process design scheme. Finite element analyses were performed to obtain the flow stress by a hot compression test at different temperature and strain rates. The control parameters of each forging process, such as temperature and effective strain, were obtained and compared to predict the suitability of the hollow main shaft forging process. Finally, high productivity reflecting material utilization ratio, internal quality, shape, and dimension was verified by the prototypes manufactured by the proposed forging process for hollow main shafts.

Reducing the Incidence of Cast-related Skin Complications in Children Treated With Cast Immobilization.

Science.gov (United States)

Difazio, Rachel L; Harris, Marie; Feldman, Lanna; Mahan, Susan T

2017-12-01

Cast immobilization remains the mainstay of pediatric orthopaedic care, yet little is known about the incidence of cast-related skin complications in children treated with cast immobilization. The purposes of this quality improvement project were to: (1) establish a baseline rate of cast-related skin complications in children treated with cast immobilization, (2) identify trends in children who experienced cast-related skin complications, (3) design an intervention aimed at decreasing the rate of cast-related skin complications, and (4) determine the effectiveness of the intervention. A prospective interrupted time-series design was used to determine the incidence of cast-related skin complications overtime and compare the rates of skin complications before and after an intervention designed to decrease the incidence of cast-related heel complications. All consecutive patients who were treated with cast immobilization from September 2012 to September 2014 were included. A cast-related skin complications data collection tool was used to capture all cast-related skin complications. A high rate of heel events was noted in our preliminary analysis and an intervention was designed to decrease the rate of cast-related skin complications, including the addition of padding during casting and respective provider education. The estimated cast-related skin events rate for all patients was 8.9 per 1000 casts applied. The rate for the total preintervention sample was 13.6 per 1000 casts which decreased to 6.6 in the postintervention sample. When examining the heel-only group, the rate was 17.1 per 1000 lower extremity casts applied in the preintervention group and 6.8 in the postintervention group. Incorporating padding to the heel of lower extremity cast was an effective intervention in decreasing the incidence of cast-related skin complications in patients treated with cast immobilization. Level II.

Die Britse owerheid en die onderwys op Heidelberg gedurende die ...

African Journals Online (AJOL)

The establishment of Christian National Education (CNE) Schools stimulated the concept of mother tongue education. Oor die klaskamerpraktyk en die werklike gehalte van onderrig tydens die kampskooltydperk is daar min bekend. Heidelberg wat na 1902 in 'n belangrike onderwyssentrum in Transvaal ontwikkel het, het ...

Sedimentêre omgewings van die Inhaca-eilandstelsel met spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente spesiale verwysing na die petrografiese en geochemiese eienskappe van die sedimente

Directory of Open Access Journals (Sweden)

Marieke Peché

2011-09-01

Full Text Available Die Inhaca-eilandstelsel is geleë langs die suidooskus van Mosambiek. Die oostekant van die stelsel grens aan die Indiese Oseaan en die westekant aan die Baai van Maputo. Hierdie eilandstelsel bestaan uit Inhaca- en Portugese eiland, asook ’n groep sandbanke wat van die noordlike punt van Inhaca na Portugese eiland strek. Die doel van hierdie studie is om die verskillende moderne en oer-sedimentêre omgewings op die eilandstelsel te identifiseer en te beskryf, die invloed van getye en golfaksie op die moderne sedimentêre omgewing vas te stel en die geochemiese en petrografiese samestelling van die geologiese eenhede te bepaal.

Die Ware Buch und die Philologie

Directory of Open Access Journals (Sweden)

Bernhard Hurch

2017-10-01

Full Text Available Die im 19. Jahrhundert sich verändernden Produktionsbedingungen für Druckwerke (Buchdruck, Satz, Papier, Bindung wirkten katalysierend auf die Fachkonstitution und Institutionalisierung der Philologien. Hier steht der tatsächliche Buchmarkt im Vordergrund der Darstellung, das Käuferpublikum und die Voraussetzungen des Vertriebs. Dazu gehören auch die Rezension als entstehende Textsorte und die rasch arbeitenden Rezensionsorgane. F.-R. Hausmann wurde in den letzten Jahren unentbehrlicher Mitarbeiter dieses im Rahmen des Grazer Schuchardt-Projekts "Netzwerk des Wissens" angesiedelten Ansatzes.

Computer aided system for parametric design of combination die

Science.gov (United States)

Naranje, Vishal G.; Hussein, H. M. A.; Kumar, S.

2017-09-01

In this paper, a computer aided system for parametric design of combination dies is presented. The system is developed using knowledge based system technique of artificial intelligence. The system is capable to design combination dies for production of sheet metal parts having punching and cupping operations. The system is coded in Visual Basic and interfaced with AutoCAD software. The low cost of the proposed system will help die designers of small and medium scale sheet metal industries for design of combination dies for similar type of products. The proposed system is capable to reduce design time and efforts of die designers for design of combination dies.

Thermodynamic analysis of as-cast and heat-treated microstructures of Mg-Ce-Nd alloys

International Nuclear Information System (INIS)

Groebner, Joachim; Kozlov, Artem; Schmid-Fetzer, Rainer; Easton, Mark A.; Zhu Suming; Gibson, Mark A.; Nie, Jian-Feng

2011-01-01

Alloys based on Mg-rare earth (RE) systems are of increasing technical interest in automotive powertrain applications due to their superior elevated temperature creep resistance. However, there is a deficiency in the literature of phase diagrams of multi-component RE systems that could assist alloy development and composition refinement for enhanced property optimization. The phase relationships in the Mg-rich corner of the Mg-Ce-Nd system have been investigated through the evaluation of selected compositions in the as-cast and heat-treated condition. Consistent thermodynamic CALPHAD-type assessments have also been generated for the Mg-Ce-Nd system. It is shown that this system reveals a significant degree of metastability under technologically significant solidification conditions (i.e. permanent-mould or high-pressure die casting). This is simulated in thermodynamic calculations by suppression of the RE 5 Mg 41 phase and reasonable agreement is found with the as-cast microstructures. After heat treatment these microstructures transform, depending on the alloy composition, into phase assemblies consistent with the calculated stable equilibrium phase diagram. It is the elucidation of such metastable phase formation and the subsequent transformation from the as-cast to the heat-treated state that is a particular strength of the thermodynamic approach and which makes it a powerful tool for alloy development.

Thermodynamic analysis of as-cast and heat-treated microstructures of Mg-Ce-Nd alloys

Energy Technology Data Exchange (ETDEWEB)

Groebner, Joachim; Kozlov, Artem [Institute of Metallurgy, Clausthal University of Technology, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany); Schmid-Fetzer, Rainer, E-mail: schmid-fetzer@tu-clausthal.de [Institute of Metallurgy, Clausthal University of Technology, Robert-Koch-Str. 42, D-38678 Clausthal-Zellerfeld (Germany); Easton, Mark A.; Zhu Suming [CAST CRC, Department of Materials Engineering, Monash University, Victoria 3800 (Australia); Gibson, Mark A. [CAST CRC, CSIRO Process Science and Engineering, Clayton, Victoria 3169 (Australia); Nie, Jian-Feng [CAST CRC, Department of Materials Engineering, Monash University, Victoria 3800 (Australia)

2011-01-15

Alloys based on Mg-rare earth (RE) systems are of increasing technical interest in automotive powertrain applications due to their superior elevated temperature creep resistance. However, there is a deficiency in the literature of phase diagrams of multi-component RE systems that could assist alloy development and composition refinement for enhanced property optimization. The phase relationships in the Mg-rich corner of the Mg-Ce-Nd system have been investigated through the evaluation of selected compositions in the as-cast and heat-treated condition. Consistent thermodynamic CALPHAD-type assessments have also been generated for the Mg-Ce-Nd system. It is shown that this system reveals a significant degree of metastability under technologically significant solidification conditions (i.e. permanent-mould or high-pressure die casting). This is simulated in thermodynamic calculations by suppression of the RE{sub 5}Mg{sub 41} phase and reasonable agreement is found with the as-cast microstructures. After heat treatment these microstructures transform, depending on the alloy composition, into phase assemblies consistent with the calculated stable equilibrium phase diagram. It is the elucidation of such metastable phase formation and the subsequent transformation from the as-cast to the heat-treated state that is a particular strength of the thermodynamic approach and which makes it a powerful tool for alloy development.

Die tug oor ampsdraers tydens die doleansie van 1886

Directory of Open Access Journals (Sweden)

J. Visser

1986-06-01

Full Text Available In art 29 van die Nederlandse Geloofsbelydenis word bely: “Die merktekens om die ware Kerk te ken is die volgende: As die Kerk die suiwere prediking van die evangelie uitoefen, as dit die suiwer bediening van die sakramente gebruik soos Christus dit ingestel het, as die kerklike tug gebruik word om die sondes te straf.” Dit spreek vanself dat wanneer ampsdraers, aan wie Christus sy kudde toevertrou het (Hand 20 : 28, met leer en /of lewenswandel in sonde volhard en nie daarin met tug gestuit word nie, word die ware kerk nie gebou nie maar afgebreek. 0ns sal later in hierdie artikel aantoon hoedanig die suiwer tug oor ampsdraers, veral leertug, tydens die Doleansie tot skade van die kerk van Christus agterweë gebly het.

Assured fitness returns in a social wasp with no worker caste.

Science.gov (United States)

Lucas, Eric R; Field, Jeremy

2011-10-07

The theory of assured fitness returns proposes that individuals nesting in groups gain fitness benefits from effort expended in brood-rearing, even if they die before the young that they have raised reach independence. These benefits, however, require that surviving nest-mates take up the task of rearing these young. It has been suggested that assured fitness returns could have favoured group nesting even at the origin of sociality (that is, in species without a dedicated worker caste). We show that experimentally orphaned brood of the apoid wasp Microstigmus nigrophthalmus continue to be provisioned by surviving adults for at least two weeks after the orphaning. This was the case for brood of both sexes. There was no evidence that naturally orphaned offspring received less food than those that still had mothers in the nest. Assured fitness returns can therefore represent a real benefit to nesting in groups, even in species without a dedicated worker caste.

Shape Accuracy of Iron Precision Castings in Terms of Ceramic Moulds Physical Properties Anisotropy

Directory of Open Access Journals (Sweden)

Biernacki R.

2014-03-01

Full Text Available While analyzing shape accuracy of ferroalloy precision castings in terms of ceramic moulds physical anisotropy, low-alloy steel castings ("cover" and cast iron ("plate" were included. The basic parameters in addition to the product linear shape accuracy are flatness deviations, especially due to the expanded flat surface which is cast plate. For mentioned castings surface micro-geometry analysis was also carried, favoring surface load capacity tp50 for Rmax = 50%. Surface load capacity tp50 obtained for the cast cover was compared with machined product, and casting plate surface was compared with wear part of the conveyor belt. The results were referred to anisotropy of ceramic moulds physical properties, which was evaluated by studying ceramic moulds samples in computer tomography equipment Metrotom 800

Die kritiek van tradisie en die tradisie van kritiek in die Geesteswetenskappe. 'n Rekonstruksie van die debat tussen Habermas en Gadamer

OpenAIRE

Duvenage, Pieter

2013-01-01

In hierdie bydrae word die bekende debat (1967-1971) tussen Jürgen Habermas en Hans-Georg Gadamer gerekonstrueer. Die debat word hier in noue samehang met die kwessie van die geesteswetenskappe gelees. Die bydrae val in vier dele uiteen. In die eerste afdeling word Habermas se opening tot die debat in vyf onderafdelings uiteengesit. Dit gaan hier oor Gadamer se verdediging van tradisie en Habermas se kritiek op die begrip (1.1). In antwoord op Gadamer se begrip van tradisie ontwerp Habermas s...

A comparison of the accuracy of patterns processed from an inlay casting wax, an auto-polymerized resin and a light-cured resin pattern material.

Science.gov (United States)

Rajagopal, Praveen; Chitre, Vidya; Aras, Meena A

2012-01-01

Traditionally, inlay casting waxes have been used to fabricate patterns for castings. Newer resin pattern materials offer greater rigidity and strength, allowing easier laboratory and intraoral adjustment without the fear of pattern damage. They also claim to possess a greater dimensional stability when compared to inlay wax. This study attempted to determine and compare the marginal accuracy of patterns fabricated from an inlay casting wax, an autopolymerized pattern resin and a light polymerized pattern resin on storage off the die for varying time intervals. Ten patterns each were fabricated from an inlay casting wax (GC Corp., Tokyo, Japan), an autopolymerized resin pattern material (Pattern resin, GC Corp, Tokyo, Japan) and a light-cured resin pattern material (Palavit GLC, Hereaus Kulzer GmbH, Germany). The completed patterns were stored off the die at room temperature. Marginal gaps were evaluated by reseating the patterns on their respective dies and observing it under a stereomicroscope at 1, 12, and 24 h intervals after pattern fabrication. The results revealed that the inlay wax showed a significantly greater marginal discrepancy at the 12 and 24 h intervals. The autopolymerized resin showed an initial (at 1 h) marginal discrepancy slightly greater than inlay wax, but showed a significantly less marginal gap (as compared to inlay wax) at the other two time intervals. The light-cured resin proved to be significantly more dimensionally stable, and showed minimal change during the storage period. The resin pattern materials studied, undergo a significantly less dimensional change than the inlay waxes on prolonged storage. They would possibly be a better alternative to inlay wax in situations requiring high precision or when delayed investment (more than 1 h) of patterns can be expected.

Die transvaalse ontwerp-ordonnansie oor die onderwys

Directory of Open Access Journals (Sweden)

J. C. Coetzee

1952-03-01

Full Text Available In ’n Buitengewone Provinsiale Koerant van die Provinsie Transvaal is onder datum 25 Junie 1952 gepubliseer ’n „Ontwerp-Ordonnansie tot samevatting en wysiging van die Wette betreffende die Sentrale Beheer van die Onderwys, die Plaaslike Beheer van Skole, Godsdiensonderrig in Openbare Skole, Taal en die Onderwys, Onderwyspersoneel, Verpligte Onderwys, Toelating van Leerlinge tot Skole, Klasse of Inrigtings, Openbare Onderwys, Private Skole, Onderwys vir Kleurlinge en Asiate en Onderwys vir Naturelle, en om vir sake in verband daarmee voorsiening te maak” .

DIE PLEK VAN SANG EN MUSIEK IN DIE PROTESTANTSE ...

African Journals Online (AJOL)

Test

Sy moet hierdie opdrag uitvoer deur mid del van die Prediking d.w.s. deur middel van die Woord-vorm, maar ook deur die bediening van die sakramente, dws. deur middel van die vorm van die Daad. Maar nou wil God nie hê dat die Kerk slegs één maal die Evangelie sal predik en die mense sal doop om hulle daarna.

Do not let death do us part: ‘find-me' signals in communication between dying cells and the phagocytes

Science.gov (United States)

Medina, C B; Ravichandran, K S

2016-01-01

The turnover and clearance of cells is an essential process that is part of many physiological and pathological processes. Improper or deficient clearance of apoptotic cells can lead to excessive inflammation and autoimmune disease. The steps involved in cell clearance include: migration of the phagocyte toward the proximity of the dying cells, specific recognition and internalization of the dying cell, and degradation of the corpse. The ability of phagocytes to recognize and react to dying cells to perform efficient and immunologically silent engulfment has been well-characterized in vitro and in vivo. However, how apoptotic cells themselves initiate the corpse removal and also influence the cells within the neighboring environment during clearance was less understood. Recent exciting observations suggest that apoptotic cells can attract phagocytes through the regulated release of ‘find-me' signals. More recent studies also suggest that these find-me signals can have additional roles outside of phagocyte attraction to help orchestrate engulfment. This review will discuss our current understanding of the different find-me signals released by apoptotic cells, how they may be relevant in vivo, and their additional roles in facilitating engulfment. PMID:26891690

USE OF HIGH-STRENGTH BAINITIC CAST IRON FOR PRODUCING GEAR WHEELS

Directory of Open Access Journals (Sweden)

A. I. Pokrovskiy

2015-01-01

Full Text Available The advantages and drawbacks of high-strength cast irons with bainitic structure are reviewed basing on the authors’ own experience in the production of critical partsfrom this material and on the analysis of world trends. A possibility of the replacement of alloy steels by bainitic cast iron in manufacturing critical machine parts is discussed.

METHODS OF RECEIVING OF FINE-GRAINED STRUCTURE OF CASTINGS AT CRYSTALLIZATION

Directory of Open Access Journals (Sweden)

N. K. Tolochko

2012-01-01

Full Text Available The article deals with methods for fine-grained structure of ingots during crystallization depending on the used foundry technologies. It is shown that by using modern scientific and technological advances may improve the traditional and the development of new casting processes, providing production of cast parts with over fine-grained structure and enhanced properties.

Thomas Erastus oor die struktuur van die gemeenskap'^

African Journals Online (AJOL)

óók aansprake en regte het, is die opvatting dat sowel die burgerlike gemeenskap as die kerk 'n perfecta societas sibi sufficiens is, nié werklik aanvaar nie. Die Middeleeuse gemeenskap was die corpus christianum,. 'n gemeenskap wat nie deur fisiese of politieke grense beperk was nie. Sy grense het gelê waar die grense ...

Influence of Addition of Briquettes with Dust Content into the Charge of Electric Induction Furnace on Cast Iron Quality

Directory of Open Access Journals (Sweden)

Pribulová A.

2012-09-01

Full Text Available Foundry dust from blasting and grinding of castings contain a high amount of iron, ergo it is possible its recycling in foundry process. Dust was compacted by briquetting, two kinds of briquettes were prepared (A contained 95% magnetic part of dust from casting blasting +5% bentonite and B contained 95% mixture of dust from casting grinding and magnetic part of dust from casting blasting + 5% bentonite and used as a part of charge into the electric induction furnace. It was found that addition of briquettes has had an influence of a chemical composition of cast iron above all on content of sulphur, phosphorus and silicon. It was not reflected in decrease in tensile strength and in microstructure. Yield of metal from briquettes was not lower then 70%.

Influence of Addition of Briquettes with Dust Content into the Charge of Electric Induction Furnace on Cast Iron Quality

Directory of Open Access Journals (Sweden)

A. Pribulová

2012-09-01

Full Text Available Foundry dust from blasting and grinding of castings contain a high amount of iron, ergo it is possible its recycling in foundry process.Dust was compacted by briquetting, two kinds of briquettes were prepared (A contained 95% magnetic part of dust from casting blasting+5% bentonite and B contained 95% mixture of dust from casting grinding and magnetic part of dust from casting blasting + 5%bentonite and used as a part of charge into the electric induction furnace. It was found that addition of briquettes has had an influence of a chemical composition of cast iron above all on content of sulphur, phosphorus and silicon. It was not reflected in decrease in tensile strength and in microstructure. Yield of metal from briquettes was not lower then 70%.

Die vestiging van die Kerk in Natal, die Vrystaat en Transvaal na ...

African Journals Online (AJOL)

as eerste predikant van die Voortrekkers laat orden en bevestig. Daama het verskeie kerksake van tyd tot tyd aandag geniet. Met betrekking tot die bevestiging van huwelike stel Retief 'n meer ordelike reëling daar, naamlik dat die gebooie van voomemende egpa- re van nou af drie maal in die kerk afgekondig moes wrord ...

Die Starter: A New System to Manage Early Feasibility in Sheet Metal Forming

Science.gov (United States)

Narainen, Rodrigue; Porzner, Harald

2016-08-01

Die Starter, a new system developed by ESI Group, allows the user to drastically reduce the number of iterations during the early tool process feasibility. This innovative system automatically designs the first quick die face, generating binder and addendum surfaces (NURBS surfaces) by taking account the full die process. Die Starter also improves the initial die face based on feasibility criteria (avoiding splits, wrinkles) by automatically generating the geometrical modifications of the binder and addendum and the bead restraining forces with minimal material usage. This paper presents a description of the new system and the methodology of Die Starter. Some industrial examples are presented from the part geometry to final die face including automatic developed flanges, part on binder and inner binder.

Die historiese betroubaarheid van die aartsvadervertellinge. 'n Beknopte bespreking van die huidige debat na aanleiding van die jongste publikasie

Directory of Open Access Journals (Sweden)

W. Vosloo

1982-08-01

Full Text Available Die afgelope twintig jaar was daar �n toenemende belangstelling in die aartsvadervertellinge in Genesis. Benewens die talle tydskrifartikels het skrywers soos die volgende ook boeke oor die onderwerp die lig laat sien: A. Parrot (1962, W. M. Clark (1964, R. Kilian (1966, R. E. Clements (1967, N. Lohfink (1967, H. Weidemann (1968, R. Martin-Achard (1969, T. L. Thompson (1974, J. van Seters (1975, J. P. Fokkelman (1975, C. Westermann (1976, R. Rendtorff (1977, J. Bright (1977, W. McKane (1979 en A. R. Millard en D. J. Wiseman (1980.

Prediking aan die hand van die metafoor van fiksieskryf

African Journals Online (AJOL)

p1243322

HTS 64(3) 2008 siening van die self en waarheid. In die pre-moderne paradigma kan die dominante metafoor verstaan word aan die hand van 'n spieël wat die lig uit 'n transendente oorsprong weerkaats, terwyl die moderne paradigma uitgedruk word met die metafoor van 'n lamp wat 'n eie, oorspronklike lig binne die self.

"Split Cast Mounting: Review and New Technique".

Science.gov (United States)

Gundawar, S M; Pande, Neelam A; Jaiswal, Priti; Radke, U M

2014-12-01

For the fabrication of a prosthesis, the Prosthodontist meticulously performs all the steps. The laboratory technician then make every effort/strives to perform the remaining lab procedures. However when the processed dentures are remounted on the articulator, some changes are seen. These changes may be divided into two categories: Pre-insertion and post-insertion changes, which deal with the physical properties of the materials involved (Parker, J Prosthet Dent 31:335-342, 1974). Split cast mounting is the method of mounting casts on the articulator. It is essentially a maxillary cast constructed in two parts with a horizontal division. The procedure allows for the verification of the accuracy of the initial mounting and the ease of removal and replacement of the cast. This provides a precise means of correcting the changes in occlusion occurring as a result of the processing technique (Nogueira et al., J Prosthet Dent 91:386-388, 2004). Instability of the split mounting has always been a problem to the Prosthodontist thereby limiting its use. There are various materials mentioned in the literature. The new technique by using Dowel pins and twill thread is very easy, cheaper and simple way to stabilize the split mounting. It is useful and easy in day to day laboratory procedures. The article presents different methods of split cast mounting and the new procedure using easily available materials in prosthetic laboratory.

Integrated System of Thermal/Dimensional Analysis for Quality Control of Metallic Melt and Ductile Iron Casting Solidification

Science.gov (United States)

Stan, Stelian; Chisamera, Mihai; Riposan, Iulian; Neacsu, Loredana; Cojocaru, Ana Maria; Stan, Iuliana

2018-03-01

The main objective of the present work is to introduce a specific experimental instrument and technique for simultaneously evaluating cooling curves and expansion or contraction of cast metals during solidification. Contraction/expansion analysis illustrates the solidification parameters progression, according to the molten cast iron characteristics, which are dependent on the melting procedure and applied metallurgical treatments, mold media rigidity and thermal behavior [heat transfer parameters]. The first part of the paper summarizes the performance of this two-mold device. Its function is illustrated by representative shrinkage tendency results in ductile cast iron as affected by mold rigidity (green sand and furan resin sand molds) and inoculant type (FeSi-based alloys), published in part previously. The second part of the paper illustrates an application of this equipment adapted for commercial foundry use. It conducts thermal analysis and volume change measurements in a single ceramic cup so that mold media as well as solidification conditions are constants, with cast iron quality as the variable. Experiments compared gray and ductile cast iron solidification patterns. Gray iron castings are characterized by higher undercooling at the beginning and at the end of solidification and lower graphitic expansion. Typically, ductile cast iron exhibits higher graphitic, initial expansion, conducive for shrinkage formation in soft molds.

SPRAY CASTING

OpenAIRE

SALAMCI, Elmas

2010-01-01

ABSTRACT This paper is designed to provide a basic review of spray casting. A brief overview of the historical development of spray  casting and the description of plant and equipment have been given. Following metallurgical characteristics of spray formed alloys, process parameters and solidification mechanism of spray deposition have been discussed in detail. Finally, microstructure and mechanical properties of the selected spray cast Al-Zn-Mg-Cu alloys have been presented and comp...

Ontsporing van die regstaatsbegrip en sy konsekwensies vir die afrikanervolk

Directory of Open Access Journals (Sweden)

N. G.S. Van der Walt

1966-03-01

Full Text Available Die opvatting van die suiwere regstaat bring sy vraagstukke mee wanneer dit in verband gebring word met die leer van die soewereiniteit in eie kring. Laasgenoemde leer wortel in die geloof dat God die mens roep tot diens aan Hom, en dat die mens vry moet wees om ten opsigte van alle lewensaspekte God na die hoogste mate te kan dien. Hierdie verskeidenheid van aspekte is deur dr. A. Kuyper en sy volgelinge gesistemati- seer tot menslike verbande en lewenskringe, elk met ’n be- paalde sfeer waarin ander kringe nie mag inmeng nie. Elkeen is dan soewerein binne sy eie kring. Met verwysing na die staat is dan gespreek van die staatstaak as synde die hand- hawing van die reg, en omdat die staat in toenemende mate hom veral in die latere tyd ook besig gehou het met bedrywig- hede wat nouliks as van juridiese aard beskou kan word, is daar die onderskeid gemaak tussen die primêre en sekundêre taak van die staat. Die sistematiek van die wetsidee, deur prof. Dooyeweerd ontwikkel, waar die staat sy bestemmingsfunksie in die regsaspek vind, het vanselfsprekend geen plek vir so 'n dualistiese staatstaak nie, en die oplossing is deur sommige daarin gesoek om sulke staatsoptrede te vertolk as hebbende wel betrekking op die regsgemeenskap of die regsverkeer. Staatsondernemings soos paaie, spoorweë, spellingreëling, ens. word dan beskou as noodsaaklik vir die instandhouding van die regsgemeenskap en regsverkeer. Tereg wys A. M. Donner1 daarop dat so ’n vertolking eintlik neerkom op ’n oorspanning van die regsbegrip. Hy self sien dan die staatstaak in vrede- of orde-handhawing, wat in die eerste plaas wel regshandha- wing veronderstel. Onder orde word dan alles verstaan wat noodsaaklik is vir die gladde verkeer in die ontwikkelingsgang van die regsgemeenskap. Die wese van die staat het dan vol- gens hom te doen met reg, maar sy taak is meer as suiwere regshandhawing. Wat onrus verwek en die orde versteur, moet uit die openbare lewe verwyder word, en die

The taper of cast post preparation measured using innovative image processing technique

Directory of Open Access Journals (Sweden)

Al Hyiasat Ahmad S

2010-08-01

Full Text Available Abstract Background No documentation in the literature about taper of cast posts. This study was conducted to measure the degree of cast posts taper, and to evaluate its suitability based on the anatomy aspects of the common candidate teeth for post reconstruction. Methods Working casts for cast posts, prepared using Gates Glidden drills, were collected. Impressions of post spaces were made using polyvinyl siloxan putty/wash technique. Digital camera with a 10' high quality lens was used for capturing two digital images for each impression; one in the Facio-Lingual (FL and the other in the Mesio-Distal (MD directions. Automated image processing program was developed to measure the degree of canal taper. Data were analyzed using Statistical Package for Social Sciences software and One way Analysis of Variance. Results Eighty four dies for cast posts were collected: 16 for each maxillary anterior teeth subgroup, and 18 for each maxillary and mandibular premolar subgroup. Mean of total taper for all preparations was 10.7 degree. There were no statistical differences among the total taper of all groups (P = .256 or between the MD and FL taper for each subgroup. Mean FL taper for the maxillary first premolars was lower significantly (P = .003 than the maxillary FL taper of the second premolars. FL taper was higher than the MD taper in all teeth except the maxillary first premolars. Conclusions Taper produced did not reflect the differences among the anatomy of teeth. While this technique deemed satisfactory in the maxillary anterior teeth, the same could not be said for the maxillary first premolars. Careful attention to the root anatomy is mandatory.

Accurate defect die placement and nuisance defect reduction for reticle die-to-die inspections

Science.gov (United States)

Wen, Vincent; Huang, L. R.; Lin, C. J.; Tseng, Y. N.; Huang, W. H.; Tuo, Laurent C.; Wylie, Mark; Chen, Ellison; Wang, Elvik; Glasser, Joshua; Kelkar, Amrish; Wu, David

2015-10-01

Die-to-die reticle inspections are among the simplest and most sensitive reticle inspections because of the use of an identical-design neighboring-die for the reference image. However, this inspection mode can have two key disadvantages: (1) The location of the defect is indeterminate because it is unclear to the inspector whether the test or reference image is defective; and (2) nuisance and false defects from mask manufacturing noise and tool optical variation can limit the usable sensitivity. The use of a new sequencing approach for a die-to-die inspection can resolve these issues without any additional scan time, without sacrifice in sensitivity requirement, and with a manageable increase in computation load. In this paper we explore another approach for die-to-die inspections using a new method of defect processing and sequencing. Utilizing die-to-die double arbitration during defect detection has been proven through extensive testing to generate accurate placement of the defect in the correct die to ensure efficient defect disposition at the AIMS step. The use of this method maintained the required inspection sensitivity for mask quality as verified with programmed-defectmask qualification and then further validated with production masks comparing the current inspection approach to the new method. Furthermore, this approach can significantly reduce the total number of defects that need to be reviewed by essentially eliminating the nuisance and false defects that can result from a die-to-die inspection. This "double-win" will significantly reduce the effort in classifying a die-to-die inspection result and will lead to improved cycle times.

DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE HUIDIGE ...

African Journals Online (AJOL)

Test

DIE ONTVC'ERP VAN 'N SENDINGBELEID IN DIE. HUIDIGE SITUASIE. Sending is 'n deel van die vervulling van die apostoliese opdrag van die kerk. Dit geskied op grond van en in gehoorsaamheid aan Gods. \\C'oord. Teologiese besinning is daarom die eerste en grondliggende vereiste by die ontwerp van 'n ...

TECHNOLOGICAL PARAMETERS OF SLUGS CASTING OF GREY CAST IRON BY FROSTING

Directory of Open Access Journals (Sweden)

E. I. Marukovich

2009-01-01

Full Text Available The relation of geometrical parametres of casting with technological ones is shown. The monogram for definition of basic technological parametres of obtaining of castings by the method of continuously-cyclic iterative casting by freezing-up is presented.

Die sestienpersoonlikheidsfaktorvraelys as hulpmiddel by die takseersentrum

Directory of Open Access Journals (Sweden)

J. C. D. Augustyn

1988-05-01

Full Text Available The 16PF Personality Test as an aid to the assessment centre Assessment centres still remains costly and thime consuming. This study investigates the reduction of time and costs by the use of the 16 PF Personality Test as a method for measuring management dimensions. Promising results were obtained with a relatively small sample for the prediction of initiative and perseverance. Significant multiple correlations were also found for three criteria of management success. Further research may establish the use of the 16 PF as an aid to management assessment and thereby reduce the costs and time involved in assessment centres. Opsomming Takseersentrums se grootste probleem is gelee in die koste en tyd wat dit behels. Hierdie studie ondersoek die moontlikheid om beide te verminder deur die aanwending van die 16 PF Persoonlikheidsvraelys vir die meting van bestuursdimensies. Belowende resultate is met 'n relatiewe klein steekproef bevind ten opsigte van die voorspelling van inisiatiefen deursettingsvermoe. Beduidende meervoudige korrelasies is ook ten opsigte van drie kriteria van bestuursukses bevind. Verdere navorsing kan die gebruik van die 16 PF as hulpmiddel by bestuursevaluering vestig en sodoende die tydsduur en koste van takseersentrums verminder.

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅳ

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2010-11-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron. Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron, uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditional materials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

Colour Metallography of Cast Iron - Chapter 3: Spheroidal Graphite Cast Iron (Ⅰ

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2010-02-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron. Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron, uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditional materials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

Colour Metallography of Cast Iron - Chapter 4: Vermicular Graphite Cast Iron (Ⅱ

Directory of Open Access Journals (Sweden)

Zhou Jiyang

2011-05-01

Full Text Available Cast iron, as a traditional metal material, has advantages of low total cost, good castability and machinability, good wear resistance and low notch sensitivity, and is still facing tough challenge in quality, property and variety of types etc. Experts and engineers studying and producing iron castings all around world extremely concern this serious challenge. Over more than 30 years, a great of research work has been carried out on how to further improve its property, expand its application and combine cast iron technology with some hi-techs (for example, computer technology. Nevertheless, cast iron is a multi-element and multi-phase alloy and has complex and variety of structures and still has great development potential in structure and property. For further studying and developing cast iron, theoretical research work is important promise, and the study on solidification process and control mechanism of graphite morphology is fundamental for improving property of cast iron and developing new type of cast iron. Metallography of cast iron normally includes two sections: liquid phase transformation and solid phase transformation. The book, Colour Metallography of Cast Iron, uses colour metallography technique to study solidification structures of cast irons: graphite, carbides, austenite and eutectics; and focuses on solidification processes. With progress of modern solidification theory, the control of material solidification process becomes important measure for improving traditional materials and developing new materials. Solidification structure not only influences mechanical and physical properties of cast iron, but also affects its internal quality. The book uses a large amount of colour photos to describe the formation of solidification structures and their relations. Crystallization phenomena, which cannot be displayed with traditional metallography, are presented and more phase transformation information is obtained from these colour

die korrelasie tussen die gemiddelde daaglikse toename van ...

African Journals Online (AJOL)

'n Regressielyn is uit die gegewens bereken deur 'n beswaarde regressieanaliese en die 80 persent-voorspellings- bande is bepaal. Die punte wat ver buite die normale ver- spreidingsband geval hetkon almal met goeie rede as abnor- maal beskou word (sien tabel 1) en is nie ingesluit by die statistiese berekenings nie.

The structure of abrasion-resisting castings made of chromium cast iron

Directory of Open Access Journals (Sweden)

D. Kopyciński

2011-01-01

Full Text Available In this study presents the analyse of chrome iron cast structure (as-cast condition which are used in rugged conditions abrasion-percussive and high temperature. While producing the casts of chrome iron major influence has been preserve the structure of technologi cal process parameters. The addition to Fe-C-Cr alloy Ni, Mo or Cu and then proper heat treatment leads to the improvement of functional and mechanical cast qualities. Then it is possible to develop high mechanical properties which are recommended by PN-EN12513. As can it be seen from the above research silicon is an adverse chemical element in this kind of alloy cast iron. However, the reason of cracksappearing in chrome iron casts are phosphorus eutectic microareas. When the compound of Si and P reach the critical point, described inPN-88/H-83144 outdated standard, the microareas might appear.

The deformation of wax patterns and castings in investment casting technology

Directory of Open Access Journals (Sweden)

A. Herman

2012-01-01

Full Text Available The dimensional accuracy of the final casting of Inconel alloy 738 LC is affected by many aspects. One of them is the choice of method and time of cooling wax model for precision investment casting. The main objective was to study the initial deformation of the complex shape of the casting of the rotor blades. Various approaches have been tested for cooling wax pattern. When wax models are cooling on the air, without clamping in jig for cooling, deviations from the ideal shape of the casting are very noticeable (up to 8 mm and most are in extreme positions of the model. When blade is cooled in fixing jig in water environment, the resulting deviations compared with cooling in air are significantly larger, sometimes up to 10 mm. This itself does not mean that the final shape of the casting is dimensionally more accurate with usage of wax models, which have deviations from the ideal position smaller. Another deformation occurs when shell mould is produced around wax pattern and furthermore deformations emerge while casting of blade is cooling. This paper demonstrates first steps in describing complex process of deformations of Inconel alloy blades produced with investment casting technology by comparing results from thermal imagery, simulations in foundry simulation software ProCAST 2010 and measurements from CNC scanning system Carl Zeiss MC 850. Conclusions are so far not groundbreaking, but it seems deformations of wax pattern and deformations of castings do in some cases cancel each other by having opposite directions. Describing entirely whole process of deformations will help increase precision of blade castings so that models at the beginning and blades in the end are the same.

Grindability of cast Ti-Hf alloys.

Science.gov (United States)

Kikuchi, Masafumi; Takahashi, Masatoshi; Sato, Hideki; Okuno, Osamu; Nunn, Martha E; Okabe, Toru

2006-04-01

As part of our systematic studies characterizing the properties of titanium alloys, we investigated the grindability of a series of cast Ti-Hf alloys. Alloy buttons with hafnium concentrations up to 40 mass% were made using an argon-arc melting furnace. Each button was cast into a magnesia-based mold using a dental titanium casting machine; three specimens were made for each metal. Prior to testing, the hardened surface layer was removed. The specimens were ground at five different speeds for 1 min at 0.98 N using a carborundum wheel on an electric dental handpiece. Grindability was evaluated as the volume of metal removed per minute (grinding rate) and the volume ratio of metal removed compared to the wheel material lost (grinding ratio). The data were analyzed using ANOVA. A trend of increasing grindability was found with increasing amounts of hafnium, although there was no statistical difference in the grindability with increasing hafnium contents. We also found that hafnium may be used to harden or strengthen titanium without deteriorating the grindability.

enkele fasette van die problematiek van die akademikus by die skryf

African Journals Online (AJOL)

Om verskeie redes het dit van die allergrootste belong geword dot 'n his- tories korrekte, wetenskaplike weerga- we van bogenoemde gebeure opge- teken moet word. Die sluier, in sommige gevalle am logiese redes toegepas, moes eenvoudig gelig word am gebeure wat die gewone man op stroot in Suid-Afrika dikwels ...

Die huwelik as identiteitsmerker in die Ou Testament

African Journals Online (AJOL)

p1243322

Gen 2:18). Uit die woorde van Genesis 2:24 dat man en vrou een sal wees, lei die derde formulier af dat dit “getuig dat die huwelik 'n allesinsluitende gemeenskap is ..... die formule gebruik word: “Hier volg die vertelling oor X se nageslag.” (Gen ..... verwys daarna as “intertwining the principal value concepts of tradition”.

amp' van die ouderling in die Nuwe Testament

African Journals Online (AJOL)

Jesus self het geen kerk gestig nie en daarom, veral omdat die Jesus-beweging inter mums ten opsigte van die Joodse godsdiens van sy tyd tot stand gekom het, het ...... Die klem val dus nie op die npoTCTT0fievo<; se rang of outoriteit nie, maar op sy pastorale funksie in die huishouding of huisgemeente (kyk Reicke.

Enkele opmerkings oor die intrinsieke waarde van die Latynse teks van Kodeks Bezae as herstelbron vir die Griekse teks van die Nuwe Testament

Directory of Open Access Journals (Sweden)

G. J.C. Jordaan

1985-05-01

Full Text Available Een van die belangrikste oud-Latynse vertalings word gevind in Kodeks Bezae, ’n vyfde-eeuse manuskrip van die vier Evangelies. Kodeks Bezae bevat ’n Griekse teks (D en ’n Latynse teks (d van die Evangelies langs mekaar, die Latynse teks in ’n lettertipe wat baie aan die Griekse majuskelskrif herinner. Wat hierdie dokument so merkwaardig maak, is die feit dat dit die enigste manuskrip is wat ’n Griekse Evangelie-teks uit die Westerse teksfamilie bevat.

n Oorsig van die huidige stand van navorsing oor die

African Journals Online (AJOL)

Test

7 Jun 2011 ... Die eerste maal wat dit as deel van die teks van 1 Johannes aangehaal word, is in die. 4de eeu in 'n Latynse teks, Liber Apologeticus (hf 4). Eers aan die einde van die 16de eeu is dit in 'n amptelike Katolieke uitgawe van die Vulgaat ingesluit. Die doel van die Johannesbriewe. Waarom is die Briewe ...

Die dogmatiese binding van die prediking

African Journals Online (AJOL)

genoemde probleemstelling wat ons homileties na riglyne wil soek, sonder die pretensie dat finale oplossings gevind sal word. Om hierdie probleem te ontleed is dit nodig om eers kortliks 'n begripsbepaling van die begrippe dogma, binding en prediking te maak. Vanuit die begripsbepaling kan ons dan probeer vasstel wat ...

DIE HEDENDAAGSE SIENING VAN DIE NORMERING VAN DUITS ...

African Journals Online (AJOL)

v a k t a a l k w a l i £ i k a s i e s ) neem d i e I n s t i t u t t a l l e take waar ter u i t b r e i d i n g van kennis van die Duitse taal in die buiteland. Sedert 1964 publiseer die. Institut die tydskrif Deutsch als Fremdsprache met die bylae Sprachpraxis, asook 'n handboek met die titel Deutsch - eln Lehrbuch Eur Auslander (Duits.

Die topkwark

Directory of Open Access Journals (Sweden)

R. Tegen

1998-07-01

Full Text Available ’n Oorsig van die belangrikheid van die onlangs ontdekte topkwark by Fermilab in Chicago word gegee. Daar word aangetnon dat die topkwark belangrik is in fisika van die Oerknal, oftewel "Big Bang", en in die Standaard Model van Elementêredeeltjie-fisika. Toepaslike literatuur vir verdere studie kan van die lys van verwysings in hierdie kort, nietegniese artikel, nagegaan word.

oor die inhoud en boodskap van die heidelbergse kategismus

African Journals Online (AJOL)

Smit. Oor die Inhoud en Boodskap van die Heidelbergse Kategismus. 52. Uiteraard sal dié tema saamhang met die bedoelinge agter die opstel van die Kategismus. Ook die vraag na moontlike bedoelinge of motiewe is egter 'n ingewikkelder vraag as wat miskien gedink mag word. Uiteraard was daar agter elke kategismus ...

Die vangnet van die woord: forensies-linguistiese getuienis in 'n ...

African Journals Online (AJOL)

Een van die redes daarvoor is waarskynlik die gepaardgaande sleurwerk verbonde aan die verwerking van die betrokke taaldata — iets wat egter deur die onlangse meteoriese vooruitgang in tegnologiese tegnieke op die agtergrond geskuif is en nuwe moontlikhede na vore laat kom het. In die lig van die kompleksiteit van ...