WorldWideScience

Sample records for design evaluations including

  1. Biomechanical evaluation of bending strength of spinal pedicle screws, including cylindrical, conical, dual core and double dual core designs using numerical simulations and mechanical tests.

    Science.gov (United States)

    Amaritsakul, Yongyut; Chao, Ching-Kong; Lin, Jinn

    2014-09-01

    Pedicle screws are used for treating several types of spinal injuries. Although several commercial versions are presently available, they are mostly either fully cylindrical or fully conical. In this study, the bending strengths of seven types of commercial pedicle screws and a newly designed double dual core screw were evaluated by finite element analyses and biomechanical tests. All the screws had an outer diameter of 7 mm, and the biomechanical test consisted of a cantilever bending test in which a vertical point load was applied using a level arm of 45 mm. The boundary and loading conditions of the biomechanical tests were applied to the model used for the finite element analyses. The results showed that only the conical screws with fixed outer diameter and the new double dual core screw could withstand 1,000,000 cycles of a 50-500 N cyclic load. The new screw, however, exhibited lower stiffness than the conical screw, indicating that it could afford patients more flexible movements. Moreover, the new screw produced a level of stability comparable to that of the conical screw, and it was also significantly stronger than the other screws. The finite element analysis further revealed that the point of maximum tensile stress in the screw model was comparable to the point at which fracture occurred during the fatigue test. Copyright © 2014 IPEM. Published by Elsevier Ltd. All rights reserved.

  2. Use of barusiban in a novel study design for evaluation of tocolytic agents in pregnant and neonatal monkeys, including behavioural and immunological endpoints

    DEFF Research Database (Denmark)

    Rasmussen, Allan D; Nelson, Joyce K; Chellman, Gary J

    2007-01-01

    infants entailed the design of a unique protocol to investigate all aspects of maternal and offspring well-being. Barusiban was administered to the mothers from gestation day 85 until delivery with daily subcutaneous dosages up to 2.5mg/kg body weight/day. There were no test article-related effects seen...

  3. Rationale and design of three observational, prospective cohort studies including biobanking to evaluate and improve diagnostics, management strategies and risk stratification in venous thromboembolism: the VTEval Project.

    Science.gov (United States)

    Frank, Bernd; Ariza, Liana; Lamparter, Heidrun; Grossmann, Vera; Prochaska, Jürgen H; Ullmann, Alexander; Kindler, Florentina; Weisser, Gerhard; Walter, Ulrich; Lackner, Karl J; Espinola-Klein, Christine; Münzel, Thomas; Konstantinides, Stavros V; Wild, Philipp S

    2015-07-01

    Venous thromboembolism (VTE) with its two manifestations deep vein thrombosis (DVT) and pulmonary embolism (PE) is a major public health problem. The VTEval Project aims to investigate numerous research questions on diagnosis, clinical management, treatment and prognosis of VTE, which have remained uncertain to date. The VTEval Project consists of three observational, prospective cohort studies on VTE comprising cohorts of individuals with a clinical suspicion of acute PE (with or without DVT), with a clinical suspicion of acute DVT (without symptomatic PE) and with an incidental diagnosis of VTE (PE or DVT). The VTEval Project expects to enrol a total of approximately 2000 individuals with subsequent active and passive follow-up investigations over a time period of 5 years per participant. Time points for active follow-up investigations are at months 3, 6, 12, 24 and 36 after diagnosis (depending on the disease cohort); passive follow-up investigations via registry offices and the cancer registry are performed 48 and 60 months after diagnosis for all participants. Primary short-term outcome is defined by overall mortality (PE-related death and all other causes of death), primary long-term outcome by symptomatic VTE (PE-related death, recurrence of non-fatal PE or DVT). The VTEval Project includes three 'all-comer' studies and involves the standardised acquisition of high-quality data, covering the systematic assessment of VTE including symptoms, risk profile, psychosocial, environmental and lifestyle factors as well as clinical and subclinical disease, and it builds up a large state-of-the-art biorepository containing various materials from serial blood samplings. The VTEval Project has been approved by the local data safety commissioner and the responsible ethics committee (reference no. 837.320.12 (8421-F)). Trial results will be published in peer-reviewed journals and presented at national and international scientific meetings. NCT02156401. Published by the

  4. Gradually including potential users: A tool to counter design exclusions.

    Science.gov (United States)

    Zitkus, Emilene; Langdon, Patrick; Clarkson, P John

    2018-01-01

    The paper describes an iterative development process used to understand the suitability of different inclusive design evaluation tools applied into design practices. At the end of this process, a tool named Inclusive Design Advisor was developed, combining data related to design features of small appliances with ergonomic task demands, anthropometric data and exclusion data. When auditing a new design the tool examines the exclusion that each design feature can cause, followed by objective recommendations directly related to its features. Interactively, it allows designers or clients to balance design changes with the exclusion caused. It presents the type of information that enables designers and clients to discuss user needs and make more inclusive design decisions. Copyright © 2017. Published by Elsevier Ltd.

  5. Evaluation in participatory design

    DEFF Research Database (Denmark)

    Bossen, Claus; Dindler, Christian; Iversen, Ole Sejer

    2016-01-01

    his paper focuses on evaluation in Participatory Design (PD), and especially upon how the central aims of mutual learning, empowerment, democracy and workplace quality have been assessed. We surveyed all Participatory Design Conference papers (1990-2014) and papers from special journal issues on PD...

  6. A framework for including family health spillovers in economic evaluation

    NARCIS (Netherlands)

    H. Al-Janabi (Hareth); N.J.A. van Exel (Job); W.B.F. Brouwer (Werner); J. Coast (Joanna)

    2016-01-01

    textabstractHealth care interventions may affect the health of patients' family networks. It has been suggested that these health spillovers? should be included in economic evaluation, but there is not a systematic method for doing this. In this article, we develop a framework for including health

  7. Electron ring design for HERA, including spin-matching

    International Nuclear Information System (INIS)

    Skuja, A.; Hand, L.; Steffen, K.; Barber, D.

    1984-01-01

    A. Skuja has been working in collaboration with Professor Lou Hand in obtaining an optics for the electron ring at HERA that satisfies the usual constraints of an electron storage ring, but in addition allows longitudinal polarization in the interaction region without depolarizing the electron beam completely. This collaboration effort grew out of their work on a possible electron ring at Fermilab. When this project was degraded in priority at Fermilab, they turned their attention to the HERA project at DESY. The HERA project will have an electron ring of about 30 GeV e - (or e + ) incident on 800 GeV protons. Recently it has been decided that the collisions should be head on (0 0 crossing), although all previous designs had a crossing angle of the 2 beams of 20 mrad. Professors Hand and Skuja implemented a complete program in the last year and a half that could fit the usual Turis parameters as well as the so called 12 spin-matching conditions of Chao and Yukoya for all possible machine elements including solenoids. The program has the possibility of fully coupling vertical and horizontal motion using the usual eigenvalue method

  8. When users cannot be included in inclusive design

    DEFF Research Database (Denmark)

    Herriott, Richard

    2012-01-01

    and disabled users make the need for useability and pleasurability even more important since alternative products are comparatively few. This paper examines the workarounds two teams of designers have used to reduce the demands placed on emphysema patients and elderly users during inclusive design processes......Inclusive Design (ID) methods place a strong emphasis on user participation in designing mainstream products. In recent years researchers in the field of assistive technology (AT) have drawn on and contributed to the ID approach. There are good grounds for this association. However, the linkage...

  9. Should Intelligent Design Be Included in Today's Public School Curriculums?

    Science.gov (United States)

    Costley, Kevin C.; Killins, Pam

    2010-01-01

    The controversial concept of evolution makes up only a small part of the science curriculum stated in Arkansas. During the past few years, the curriculum topic of "Intelligent Design" has caught the attention of many science teachers in the public schools. The Intelligent Design Movement has been successful in attracting the attention of…

  10. Nuclear data evaluation methodology including estimates of covariances

    Directory of Open Access Journals (Sweden)

    Smith D.L.

    2010-10-01

    Full Text Available Evaluated nuclear data rather than raw experimental and theoretical information are employed in nuclear applications such as the design of nuclear energy systems. Therefore, the process by which such information is produced and ultimately used is of critical interest to the nuclear science community. This paper provides an overview of various contemporary methods employed to generate evaluated cross sections and related physical quantities such as particle emission angular distributions and energy spectra. The emphasis here is on data associated with neutron induced reaction processes, with consideration of the uncertainties in these data, and on the more recent evaluation methods, e.g., those that are based on stochastic (Monte Carlo techniques. There is no unique way to perform such evaluations, nor are nuclear data evaluators united in their opinions as to which methods are superior to the others in various circumstances. In some cases it is not critical which approaches are used as long as there is consistency and proper use is made of the available physical information. However, in other instances there are definite advantages to using particular methods as opposed to other options. Some of these distinctions are discussed in this paper and suggestions are offered regarding fruitful areas for future research in the development of evaluation methodology.

  11. A Framework for Including Family Health Spillovers in Economic Evaluation.

    Science.gov (United States)

    Al-Janabi, Hareth; van Exel, Job; Brouwer, Werner; Coast, Joanna

    2016-02-01

    Health care interventions may affect the health of patients' family networks. It has been suggested that these "health spillovers" should be included in economic evaluation, but there is not a systematic method for doing this. In this article, we develop a framework for including health spillovers in economic evaluation. We focus on extra-welfarist economic evaluations where the objective is to maximize health benefits from a health care budget (the "health care perspective"). Our framework involves adapting the conventional cost-effectiveness decision rule to include 2 multiplier effects to internalize the spillover effects. These multiplier effects express the ratio of total health effects (for patients and their family networks) to patient health effects. One multiplier effect is specified for health benefit generated from providing a new intervention, one for health benefit displaced by funding this intervention. We show that using multiplier effects to internalize health spillovers could change the optimal funding decisions and generate additional health benefits to society. © The Author(s) 2015.

  12. Evaluating aesthetics in design

    DEFF Research Database (Denmark)

    Folkmann, Mads Nygaard

    2010-01-01

    : an aesthetics of sensual relation and an aesthetics of communicative self-reflection. Following these concepts the article raises questions of dealing with design as a structure of sensual appearance, and of design as an act of communication that can contain an aesthetic coding in letting an idea or content...

  13. A design of a computer complex including vector processors

    International Nuclear Information System (INIS)

    Asai, Kiyoshi

    1982-12-01

    We, members of the Computing Center, Japan Atomic Energy Research Institute have been engaged for these six years in the research of adaptability of vector processing to large-scale nuclear codes. The research has been done in collaboration with researchers and engineers of JAERI and a computer manufacturer. In this research, forty large-scale nuclear codes were investigated from the viewpoint of vectorization. Among them, twenty-six codes were actually vectorized and executed. As the results of the investigation, it is now estimated that about seventy percents of nuclear codes and seventy percents of our total amount of CPU time of JAERI are highly vectorizable. Based on the data obtained by the investigation, (1)currently vectorizable CPU time, (2)necessary number of vector processors, (3)necessary manpower for vectorization of nuclear codes, (4)computing speed, memory size, number of parallel 1/0 paths, size and speed of 1/0 buffer of vector processor suitable for our applications, (5)necessary software and operational policy for use of vector processors are discussed, and finally (6)a computer complex including vector processors is presented in this report. (author)

  14. Reliability evaluation of containments including soil-structure interaction

    International Nuclear Information System (INIS)

    Pires, J.; Hwang, H.; Reich, M.

    1985-12-01

    Soil-structure interaction effects on the reliability assessment of containment structures are examined. The probability-based method for reliability evaluation of nuclear structures developed at Brookhaven National Laboratory is extended to include soil-structure interaction effects. In this method, reliability of structures is expressed in terms of limit state probabilities. Furthermore, random vibration theory is utilized to calculate limit state probabilities under random seismic loads. Earthquake ground motion is modeled by a segment of a zero-mean, stationary, filtered Gaussian white noise random process, represented by its power spectrum. All possible seismic hazards at a site, represented by a hazard curve, are also included in the analysis. The soil-foundation system is represented by a rigid surface foundation on an elastic halfspace. Random and other uncertainties in the strength properties of the structure, in the stiffness and internal damping of the soil, are also included in the analysis. Finally, a realistic reinforced concrete containment is analyzed to demonstrate the application of the method. For this containment, the soil-structure interaction effects on; (1) limit state probabilities, (2) structural fragility curves, (3) floor response spectra with probabilistic content, and (4) correlation coefficients for total acceleration response at specified structural locations, are examined in detail. 25 refs., 21 figs., 12 tabs

  15. Method for including detailed evaluation of daylight levels in Be06

    DEFF Research Database (Denmark)

    Petersen, Steffen

    2008-01-01

    Good daylight conditions in office buildings have become an important issue due to new European regulatory demands which include energy consumption for electrical lighting in the building energy frame. Good daylight conditions in offices are thus in increased focus as an energy conserving measure....... In order to evaluate whether a certain design is good daylight design or not building designers must perform detailed evaluation of daylight levels, including the daylight performance of dynamic solar shadings, and include these in the energy performance evaluation. However, the mandatory national...... calculation tool in Denmark (Be06) for evaluating the energy performance of buildings is currently using a simple representation of available daylight in a room and simple assumptions regarding the control of shading devices. In a case example, this is leading to an overestimation of the energy consumption...

  16. Including test errors in evaluating surveillance test intervals

    International Nuclear Information System (INIS)

    Kim, I.S.; Samanta, P.K.; Martorell, S.; Vesely, W.E.

    1991-01-01

    Technical Specifications require surveillance testing to assure that the standby systems important to safety will start and perform their intended functions in the event of plant abnormality. However, as evidenced by operating experience, the surveillance tests may be adversely impact safety because of their undesirable side effects, such as initiation of plant transients during testing or wearing-out of safety systems due to testing. This paper first defines the concerns, i.e., the potential adverse effects of surveillance testing, from a risk perspective. Then, we present a methodology to evaluate the risk impact of those adverse effects, focusing on two important kinds of adverse impacts of surveillance testing: (1) risk impact of test-caused trips and (2) risk impact of test-caused equipment wear. The quantitative risk methodology is demonstrated with several surveillance tests conducted at boiling water reactors, such as the tests of the main steam isolation valves, the turbine overspeed protection system, and the emergency diesel generators. We present the results of the risk-effectiveness evaluation of surveillance test intervals, which compares the adverse risk impact with the beneficial risk impact of testing from potential failure detection, along with insights from sensitivity studies

  17. Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics

    International Nuclear Information System (INIS)

    Adams, S.R.

    1985-10-01

    A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences

  18. Theory, design, and operation of liquid metal fast breeder reactors, including operational health physics

    Energy Technology Data Exchange (ETDEWEB)

    Adams, S.R.

    1985-10-01

    A comprehensive evaluation was conducted of the radiation protection practices and programs at prototype LMFBRs with long operational experience. Installations evaluated were the Fast Flux Test Facility (FFTF), Richland, Washington; Experimental Breeder Reactor II (EBR-II), Idaho Falls, Idaho; Prototype Fast Reactor (PFR) Dounreay, Scotland; Phenix, Marcoule, France; and Kompakte Natriumgekuhlte Kernreak Toranlange (KNK II), Karlsruhe, Federal Republic of Germany. The evaluation included external and internal exposure control, respiratory protection procedures, radiation surveillance practices, radioactive waste management, and engineering controls for confining radiation contamination. The theory, design, and operating experience at LMFBRs is described. Aspects of LMFBR health physics different from the LWR experience in the United States are identified. Suggestions are made for modifications to the NRC Standard Review Plan based on the differences.

  19. A structural design and analysis of a piping system including seismic load

    International Nuclear Information System (INIS)

    Hsieh, B.J.; Kot, C.A.

    1991-01-01

    The structural design/analysis of a piping system at a nuclear fuel facility is used to investigate some aspects of current design procedures. Specifically the effect of using various stress measures including ASME Boiler ampersand Pressure Vessel (B ampersand PV) Code formulas is evaluated. It is found that large differences in local maximum stress values may be calculated depending on the stress criterion used. However, when the global stress maximum for the entire system are compared the differences are much smaller, being nevertheless, for some load combinations, of the order of 50 percent. The effect of using an Equivalent Static Method (ESM) analysis is also evaluated by comparing its results with those obtained from a Response Spectrum Method (RSM) analysis with the modal responses combined by using the absolute summation (ABS), by using the square root of the squares (SRSS), and by using the 10 percent method (10PC). It is shown that for a spectrum amplification factor (equivalent static coefficient greater than unity) of at least 1.32 must be used in the current application of the ESM analysis in order to obtain results which are conservative in all aspects relative to an RSM analysis based on ABS. However, it appears that an adequate design would be obtained from the ESM approach even without the use of a spectrum amplification factor. 7 refs., 3 figs., 3 tabs

  20. Measurement network design including traveltime determinations to minimize model prediction uncertainty

    NARCIS (Netherlands)

    Janssen, G.M.C.M.; Valstar, J.R.; Zee, van der S.E.A.T.M.

    2008-01-01

    Traveltime determinations have found increasing application in the characterization of groundwater systems. No algorithms are available, however, to optimally design sampling strategies including this information type. We propose a first-order methodology to include groundwater age or tracer arrival

  1. Physical protection system design and evaluation

    International Nuclear Information System (INIS)

    Williams, J.D.

    1997-01-01

    The design of an effective physical protection system includes the determination of physical protection system objectives, initial design of a physical protection system, design evaluation, and probably a redesign or refinement. To develop the objectives, the designer must begin by gathering information about facility operation and conditions, such as a comprehensive description of the facility, operating conditions, and the physical protection requirements. The designer then needs to define the threat. This involves considering factors about potential adversaries: class of adversary, adversary's capabilities, and range of adversary's tactics. Next, the designer should identify targets. Determination of whether or not the materials being protected are attractive targets is based mainly on the ease or difficulty of acquisition and desirability of the material. The designer now knows the objectives of the physical protection system, that is, open-quotes what to protect against whom.close quotes The next step is to design the system by determining how best to combine such elements as fences, vaults, sensors and assessment devices, entry control elements, procedures, communication devices, and protective forces personnel to meet the objectives of the system. Once a physical protection system is designed, it must be analyzed and evaluated to ensure it meets the physical protection objectives. Evaluation must allow for features working together to ensure protection rather than regarding each feature separately. Due to the complexity of the protection systems, an evaluation usually requires modeling techniques. If any vulnerabilities are found, the initial system must be redesigned to correct the vulnerabilities and a reevaluation conducted. This paper reviews the physical protection system design and methodology mentioned above. Examples of the steps required and a brief introduction to some of the technologies used in modem physical protections system are given

  2. Script of Healthcare Technology: Do Designs of Robotic Beds Exclude or Include Users?

    DEFF Research Database (Denmark)

    Brodersen, Søsser Grith Kragh; Hansen, Meiken; Lindegaard, Hanne

    2015-01-01

    Many new product designs are currently being implemented in the healthcare sector, and this presents designers with challenges involved in socially innovative design. In this paper, we argue that designing assistive technologies requires focus on multiple users and use practices. We see the design...... of assistive technologies as design of socio-material assemblies , which include an analysis of the products already used in relation to multiple users, their practices and wishes. In the article we focus on the challenges in the implementation of two types of robotic beds used for disability care...

  3. Physical protection system design and evaluation

    International Nuclear Information System (INIS)

    Williams, J.D.

    1997-11-01

    The design of an effective physical protection system (PPS) includes the determination of the PPS objectives, the initial design of a PPS, the evaluation of the design, and probably, the redesign or refinement of the system. To develop the objectives, the designer must begin by gathering information about facility operation and conditions, such as a comprehensive description of the facility, operating conditions, and the physical protection requirements. The designer then needs to define the threat. This involves considering factors about potential adversaries: class of adversary, adversary's capabilities, and range of adversary's tactics. Next, the designer should identify targets. Determination of whether or not the materials being protected are attractive targets is based mainly on the ease or difficulty of acquisition and desirability of the material. The designer now knows the objectives of the PPS, that is, ''what to protect against whom.'' The next step is to design the system by determining how best to combine such elements as fences, vaults, sensors and assessment devices, entry control devices, communication devices, procedures, and protective force personnel to meet the objectives of the system. Once a PPS is designed, it must be analyzed and evaluated to ensure it meets the PPS objectives. Evaluation must allow for features working together to ensure protection rather than regarding each feature separately. Due to the complexity of the protection systems, an evaluation usually requires modeling techniques. If any vulnerabilities are found, the initial system must be redesigned to correct the vulnerabilities and a reevaluation conducted. After the system is installed, the threat and system parameters may change with time. If they do, the analysis must be performed periodically to ensure the system objectives are still being met

  4. Cooperation in reactor design evaluation and licensing

    International Nuclear Information System (INIS)

    Kaufer, B.; Wasylyk, A.

    2014-01-01

    In January 2007 the World Nuclear Association (WNA) established the Cooperation in Reactor Design Evaluation and Licensing (CORDEL) Working Group with the aim of stimulating a dialogue between the nuclear industry (including reactor vendors, operators and utilities) and nuclear regulators (national and international organisations) on the benefits and means of achieving a worldwide convergence of reactor safety standards for reactor designs. From the time of its inception to the present, CORDEL has evolved from a group of experts discussing how to achieve international standardisation in nuclear safety design to an established and recognised working group dedicated to analysing and forging common understandings in key areas as input to major decisions on nuclear energy policy. This paper will review the general directions and activities CORDEL plans to undertake during the next five-year period, including its general strategy, activities, priorities and interactions with its customers in order to meet its objectives. (author)

  5. Cooperation in reactor design evaluation and licensing

    Energy Technology Data Exchange (ETDEWEB)

    Kaufer, B.; Wasylyk, A. [World Nuclear Association, London (United Kingdom)

    2014-07-01

    In January 2007 the World Nuclear Association (WNA) established the Cooperation in Reactor Design Evaluation and Licensing (CORDEL) Working Group with the aim of stimulating a dialogue between the nuclear industry (including reactor vendors, operators and utilities) and nuclear regulators (national and international organisations) on the benefits and means of achieving a worldwide convergence of reactor safety standards for reactor designs. From the time of its inception to the present, CORDEL has evolved from a group of experts discussing how to achieve international standardisation in nuclear safety design to an established and recognised working group dedicated to analysing and forging common understandings in key areas as input to major decisions on nuclear energy policy. This paper will review the general directions and activities CORDEL plans to undertake during the next five-year period, including its general strategy, activities, priorities and interactions with its customers in order to meet its objectives. (author)

  6. Designing monitoring programs for chemicals of emerging concern in potable reuse ⋯ What to include and what not to include?

    KAUST Repository

    Drewes, Jorg; Anderson, Paul D.; Denslow, Nancy D.; Olivieri, Adam W.; Schlenk, Daniel K.; Snyder, Shane A.; Maruya, Keith

    2012-01-01

    This study discussed a proposed process to prioritize chemicals for reclaimed water monitoring programs, selection of analytical methods required for their quantification, toxicological relevance of chemicals of emerging concern regarding human health, and related issues. Given that thousands of chemicals are potentially present in reclaimed water and that information about those chemicals is rapidly evolving, a transparent, science-based framework was developed to guide prioritization of which compounds of emerging concern (CECs) should be included in reclaimed water monitoring programs. The recommended framework includes four steps: (1) compile environmental concentrations (e.g., measured environmental concentration or MEC) of CECs in the source water for reuse projects; (2) develop a monitoring trigger level (MTL) for each of these compounds (or groups thereof) based on toxicological relevance; (3) compare the environmental concentration (e.g., MEC) to the MTL; CECs with a MEC/MTL ratio greater than 1 should be prioritized for monitoring, compounds with a ratio less than '1' should only be considered if they represent viable treatment process performance indicators; and (4) screen the priority list to ensure that a commercially available robust analytical method is available for that compound. © IWA Publishing 2013.

  7. Designing monitoring programs for chemicals of emerging concern in potable reuse--what to include and what not to include?

    Science.gov (United States)

    Drewes, J E; Anderson, P; Denslow, N; Olivieri, A; Schlenk, D; Snyder, S A; Maruya, K A

    2013-01-01

    This study discussed a proposed process to prioritize chemicals for reclaimed water monitoring programs, selection of analytical methods required for their quantification, toxicological relevance of chemicals of emerging concern regarding human health, and related issues. Given that thousands of chemicals are potentially present in reclaimed water and that information about those chemicals is rapidly evolving, a transparent, science-based framework was developed to guide prioritization of which compounds of emerging concern (CECs) should be included in reclaimed water monitoring programs. The recommended framework includes four steps: (1) compile environmental concentrations (e.g., measured environmental concentration or MEC) of CECs in the source water for reuse projects; (2) develop a monitoring trigger level (MTL) for each of these compounds (or groups thereof) based on toxicological relevance; (3) compare the environmental concentration (e.g., MEC) to the MTL; CECs with a MEC/MTL ratio greater than 1 should be prioritized for monitoring, compounds with a ratio less than '1' should only be considered if they represent viable treatment process performance indicators; and (4) screen the priority list to ensure that a commercially available robust analytical method is available for that compound.

  8. Designing monitoring programs for chemicals of emerging concern in potable reuse ⋯ What to include and what not to include?

    KAUST Repository

    Drewes, Jorg

    2012-11-01

    This study discussed a proposed process to prioritize chemicals for reclaimed water monitoring programs, selection of analytical methods required for their quantification, toxicological relevance of chemicals of emerging concern regarding human health, and related issues. Given that thousands of chemicals are potentially present in reclaimed water and that information about those chemicals is rapidly evolving, a transparent, science-based framework was developed to guide prioritization of which compounds of emerging concern (CECs) should be included in reclaimed water monitoring programs. The recommended framework includes four steps: (1) compile environmental concentrations (e.g., measured environmental concentration or MEC) of CECs in the source water for reuse projects; (2) develop a monitoring trigger level (MTL) for each of these compounds (or groups thereof) based on toxicological relevance; (3) compare the environmental concentration (e.g., MEC) to the MTL; CECs with a MEC/MTL ratio greater than 1 should be prioritized for monitoring, compounds with a ratio less than \\'1\\' should only be considered if they represent viable treatment process performance indicators; and (4) screen the priority list to ensure that a commercially available robust analytical method is available for that compound. © IWA Publishing 2013.

  9. Design of A District Heating System Including The Upgrading of Residual Industrial Waste Heat

    NARCIS (Netherlands)

    Falcao, P.W.; Mesbah, A.; Suherman, M.V.; Wennekes, S.

    2005-01-01

    This study was aimed to evaluate the feasibility of using a waste heat stream from DSM for a District Heating System. A conceptual design was carried out with emphasis on the unit for upgrading the residual waste heat. Having reviewed heat pump technology, mechanical heat pump was found to be the

  10. SGHWR safety design and evaluation

    International Nuclear Information System (INIS)

    Smith, D.R.; Merrett, D.J.; Ward, D.A.

    1977-01-01

    The paper discusses the characteristic features of the S.G.H.W.R. and identifies the single channel concept as of considerable importance. The unique feature of the design is the provision of individual spray cooling E.C.C.S. to each channel. This spray cooling occupies a prominent position in the main line safety arguments. The reliance on this form of spray cooling leads to provision of a comprehensive E.C.C.S. system of high reliability. Duplicate systems with diverse power and water sources cover the complete pressure range to give very high confidence that spray cooling is available in all major L.O.C.A.s. On the other hand hydraulic analysis of the blowdown phase demonstrates that significant convective flow is available as an alternative/supplementary cooling regime for most faults. The reactor shutdown mechanisms have also been duplicated and will be designed to high reliabilities to give surety of reactor trip in all credible faults. The comparative performance of the two systems is considered. Extent of diversity and redundancy in trip parameters is also discussed. A feature of channel concept is that the pipe sizes can be made relatively small thus restricting rates of blowdown, and the paper discusses effects of this upon long term cooling and flooding arguments. The quantities of pipework in the primary circuit introduce considerations of integrity and the paper goes on to list the measures introduced to improve segregation and protection of individual sections of the plant so that the extent of possible L.O.C.A.s is minimised. The achievement of high standards of reliability by use of in-service inspection is covered, with particular reference to the steam drums. The impact of these inspection requirements upon the very low man-rem exposures required by U.K. utilities is also included. Finally, it is noted that the provision of containment in common with other L.W.R. practice also provides a valuable engineered safety feature. The principles of

  11. FEDS : A Framework for Evaluation in Design Science Research

    DEFF Research Database (Denmark)

    Venable, John; Pries-Heje, Jan; Baskerville, Richard

    2015-01-01

    Evaluation of design artefacts and design theories is a key activity in Design Science Research (DSR), as it provides feedback for further development and (if done correctly) assures the rigour of the research. However, the extant DSR literature provides insufficient guidance on evaluation...... to enable Design Science Researchers to effectively design and incorporate evaluation activities into a DSR project that can achieve DSR goals and objectives. To address this research gap, this research paper develops, explicates, and provides evidence for the utility of a Framework for Evaluation in Design...... Science (FEDS) together with a process to guide design science researchers in developing a strategy for evaluating the artefacts they develop within a DSR project. A FEDS strategy considers why, when, how, and what to evaluate. FEDS includes a two-dimensional characterisation of DSR evaluation episodes...

  12. Modular system design and evaluation

    CERN Document Server

    Levin, Mark Sh

    2015-01-01

    This book examines seven key combinatorial engineering frameworks (composite schemes consisting of algorithms and/or interactive procedures) for hierarchical modular (composite) systems. These frameworks are based on combinatorial optimization problems (e.g., knapsack problem, multiple choice problem, assignment problem, morphological clique problem), with the author’s version of morphological design approach – Hierarchical Morphological Multicritieria Design (HMMD) – providing a conceptual lens with which to elucidate the examples discussed. This approach is based on ordinal estimates of design alternatives for systems parts/components, however, the book also puts forward an original version of HMMD that is based on new interval multiset estimates for the design alternatives with special attention paid to the aggregation of modular solutions (system versions). The second part of ‘Modular System Design and Evaluation’ provides ten information technology case studies that enriches understanding of th...

  13. Optimal design of power system stabilizer for power systems including doubly fed induction generator wind turbines

    International Nuclear Information System (INIS)

    Derafshian, Mehdi; Amjady, Nima

    2015-01-01

    This paper presents an evolutionary algorithm-based approach for optimal design of power system stabilizer (PSS) for multi-machine power systems that include doubly fed induction generator wind turbines. The proposed evolutionary algorithm is an improved particle swarm optimization named chaotic particle swarm optimization with passive congregation (CPSO-PC) applied for finding the optimal settings of PSS parameters. Two different eigenvalue-based objectives are combined as the objective function for the optimization problem of tuning PSS parameters. The first objective function comprises the damping factor of lightly damped electro-mechanical modes and the second one includes the damping ratio of these modes. The effectiveness of the proposed method to design PSS for the power systems including DFIG (Doubly Fed Induction Generator) is extensively demonstrated through eigenvalue analysis and time-domain simulations and also by comparing its simulation results with the results of other heuristic optimization approaches. - Highlights: • A new optimization model for design of PSS in power systems including DFIG is proposed. • A detailed and realistic modeling of DFIG is presented. • A new evolutionary algorithm is suggested for solving the optimization problem of designing PSS

  14. Evaluating Tobacco Control Policies in 28 Countries (including 9 EU countries: The ITC Project

    Directory of Open Access Journals (Sweden)

    Geoffrey Fong

    2016-03-01

    Full Text Available Since its start in 2002, the ITC Project has been conducting evaluation studies of tobacco control policies via prospective cohort surveys of tobacco users in 28 countries, including 9 EU countries. This presentation will focus on the design of the ITC Project and how it differs from and complements existing evidence-gathering systems (monitoring and surveillance systems in measuring and understanding the impact of FCTC policies. The presentation will also describe the ITC Project's most recent initiatives: (1 the EUREST-PLUS study focusing on measuring the impact of the Tobacco Products Directive, and (2 a large-scale international cohort study of e-cigarettes starting in the United States, Canada, England, and Australia.

  15. Multinational design evaluation programme - 2009 annual report

    International Nuclear Information System (INIS)

    2010-06-01

    The Multinational Design Evaluation Programme (MDEP) was established in 2006 as a multinational initiative to develop innovative approaches to leverage the resources and knowledge of the national regulatory authorities who are currently or will be tasked with the review of new reactor power plant designs. MDEP comprises 13 countries' nuclear regulatory authorities and is structured under 3 design-specific working groups and 3 issue-specific working groups which meet several times a year. The OECD/NEA facilitates MDEP's activities by acting as technical secretariat for the programme. The MDEP Policy Group (PG) and the Steering Technical Committee (STC) oversee the programme. MDEP's main objectives can be defined as follows: - to enhance multilateral co-operation within existing regulatory frameworks; - to encourage multinational convergence of codes, standards and safety goals; - to implement the MDEP products in order to facilitate the licensing of new reactors, including those being developed by the Generation IV International Forum. To carry out the work, two main lines of activity have been implemented: - the exploration of opportunities for harmonisation of regulatory practices; - the cooperation on the safety reviews of specific reactor designs. MDEP engages with key stakeholders involved in ensuring the safety of new reactor designs, manufacturing, construction and operation. At this time, these stakeholders include other national regulatory authorities and international organisations involved in ensuring nuclear safety including the IAEA, Western European Nuclear Regulators' Association (WENRA), NEA Committees on Nuclear Regulatory Activities (CNRA) and Safety of Nuclear Installations (CSNI), the various reactor vendors, nuclear component manufacturers, mechanical and electrical standards development organisations, reactor operators and licensees and key industry representatives such as World Nuclear Association (WNA). To this end, the MDEP has organised a

  16. TS Fuzzy Model-Based Controller Design for a Class of Nonlinear Systems Including Nonsmooth Functions

    DEFF Research Database (Denmark)

    Vafamand, Navid; Asemani, Mohammad Hassan; Khayatiyan, Alireza

    2018-01-01

    This paper proposes a novel robust controller design for a class of nonlinear systems including hard nonlinearity functions. The proposed approach is based on Takagi-Sugeno (TS) fuzzy modeling, nonquadratic Lyapunov function, and nonparallel distributed compensation scheme. In this paper, a novel...... criterion, new robust controller design conditions in terms of linear matrix inequalities are derived. Three practical case studies, electric power steering system, a helicopter model and servo-mechanical system, are presented to demonstrate the importance of such class of nonlinear systems comprising...

  17. Evaluating an artifact in design science research

    CSIR Research Space (South Africa)

    Herselman, M

    2015-09-01

    Full Text Available In this paper, we describe the iterative evaluation of an artifact developed through the application of Design Science Research (DSR) methodology in a resource constrained environment. In the DSR process the aspect of evaluation is often done...

  18. Closed-form solutions for linear regulator design of mechanical systems including optimal weighting matrix selection

    Science.gov (United States)

    Hanks, Brantley R.; Skelton, Robert E.

    1991-01-01

    Vibration in modern structural and mechanical systems can be reduced in amplitude by increasing stiffness, redistributing stiffness and mass, and/or adding damping if design techniques are available to do so. Linear Quadratic Regulator (LQR) theory in modern multivariable control design, attacks the general dissipative elastic system design problem in a global formulation. The optimal design, however, allows electronic connections and phase relations which are not physically practical or possible in passive structural-mechanical devices. The restriction of LQR solutions (to the Algebraic Riccati Equation) to design spaces which can be implemented as passive structural members and/or dampers is addressed. A general closed-form solution to the optimal free-decay control problem is presented which is tailored for structural-mechanical system. The solution includes, as subsets, special cases such as the Rayleigh Dissipation Function and total energy. Weighting matrix selection is a constrained choice among several parameters to obtain desired physical relationships. The closed-form solution is also applicable to active control design for systems where perfect, collocated actuator-sensor pairs exist.

  19. Structural evaluation in the design of electrorefiner

    International Nuclear Information System (INIS)

    Wu, T.S.; Blomquist, C.A.; Herceg, J.E.

    1995-01-01

    The electrorefiner (ER) is one piece of the process equipment for the Integral Fast Reactor (IFR) program. The ER's principal function is to perform the pyrochemical and electrochemical refining of spent and experimental fuel elements. Its principal components include a primary vessel, a heater assembly, a support-structure assembly, a cover assembly, four electrode assemblies, four elevator and rotator assemblies, and a cover-gas system. In addition, there are various miscellaneous tools and fixtures. The electrorefiner is to be installed within an existing enclosed cell. Design requirements dictate that all equipment within the cell should not be anchored. To assess the integrity of the electrorefiner during operational and seismic loads, extensive structural analyses have been performed. This paper presents some of the major structural evaluations for the electrorefiner and its auxiliary equipment. Results show that the design code requirements are satisfied, and the integrity of the electrorefiner will not be jeopardized during operational and seismic loadings

  20. Structural evaluation in the design of electrorefiner

    International Nuclear Information System (INIS)

    Wu, Ting-shu; Blomquist, C.A.; Herceg, J.E.

    1995-01-01

    The electrorefiner is one piece of the process equipment for the Integral Fast Reactor (IFR) program. Its principal components include a primary vessel, a heater assembly, a support-structure assembly, a cover assembly, four electrode assemblies, four elevator and rotator assemblies, and a cover-gas system. In addition, there are various miscellaneous tools and fixtures. The electrorefiner is to be installed within an existing enclosed cell. Design requirements dictate that all equipment within the cell should not be anchored. To assess the integrity of the electrorefiner during operational and seismic loads, extensive structural analyses have been performed. This paper presents some of the major structural evaluations for the electrorefiner and its auxiliary equipment. Results show that the design code requirements are satisfied, and the integrity of the electrorefiner will not be jeopardized during operational and seismic loadings

  1. Design and Optimization of Capacitated Supply Chain Networks Including Quality Measures

    Directory of Open Access Journals (Sweden)

    Krystel K. Castillo-Villar

    2014-01-01

    Full Text Available This paper presents (1 a novel capacitated model for supply chain network design which considers manufacturing, distribution, and quality costs (named SCND-COQ model and (2 five combinatorial optimization methods, based on nonlinear optimization, heuristic, and metaheuristic approaches, which are used to solve realistic instances of practical size. The SCND-COQ model is a mixed-integer nonlinear problem which can be used at a strategic planning level to design a supply chain network that maximizes the total profit subject to meeting an overall quality level of the final product at minimum costs. The SCND-COQ model computes the quality-related costs for the whole supply chain network considering the interdependencies among business entities. The effectiveness of the proposed solution approaches is shown using numerical experiments. These methods allow solving more realistic (capacitated supply chain network design problems including quality-related costs (inspections, rework, opportunity costs, and others within a reasonable computational time.

  2. How to include frequency dependent complex permeability Into SPICE models to improve EMI filters design?

    Science.gov (United States)

    Sixdenier, Fabien; Yade, Ousseynou; Martin, Christian; Bréard, Arnaud; Vollaire, Christian

    2018-05-01

    Electromagnetic interference (EMI) filters design is a rather difficult task where engineers have to choose adequate magnetic materials, design the magnetic circuit and choose the size and number of turns. The final design must achieve the attenuation requirements (constraints) and has to be as compact as possible (goal). Alternating current (AC) analysis is a powerful tool to predict global impedance or attenuation of any filter. However, AC analysis are generally performed without taking into account the frequency-dependent complex permeability behaviour of soft magnetic materials. That's why, we developed two frequency-dependent complex permeability models able to be included into SPICE models. After an identification process, the performances of each model are compared to measurements made on a realistic EMI filter prototype in common mode (CM) and differential mode (DM) to see the benefit of the approach. Simulation results are in good agreement with the measured ones especially in the middle frequency range.

  3. Optimal Design and Real Time Implementation of Autonomous Microgrid Including Active Load

    OpenAIRE

    Mohamed A. Hassan; Muhammed Y. Worku; Mohamed A. Abido

    2018-01-01

    Controller gains and power-sharing parameters are the main parameters affect the dynamic performance of the microgrid. Considering an active load to the autonomous microgrid, the stability problem will be more involved. In this paper, the active load effect on microgrid dynamic stability is explored. An autonomous microgrid including three inverter-based distributed generations (DGs) with an active load is modeled and the associated controllers are designed. Controller gains of the inverters ...

  4. Design for Motivation: Evaluation of a Design Tool

    Directory of Open Access Journals (Sweden)

    Dimitra Chasanidou

    2018-02-01

    Full Text Available Design for motivation constitutes a design practice that focuses on the activation of human motives to perform an action. There is an increasing need to design motivational and engaging mechanisms for voluntary systems, such as innovation platforms, where user participation is a key target. When designing for motivation, a challenge of the early design phases is the selection of appropriate design tool and strategy. The current work presents a design tool, namely DEMO (DEsign for MOtivation, and evaluates its design process. The tool provides multidisciplinary teams with a user-centred, structured method to ideate and ultimately develop a consistent design plan to engage the users of innovation platforms. The evaluation study analysed the tool’s contribution to the design of motivational innovation platforms, utilising three data collection methods: a protocol analysis, interviews and questionnaires. The results discuss the experiences of 32 users with the development of motivation concepts, the group and the user activities, as well as their creativity aspects. Structured processes and the use of artefacts were found to be productive practices in the early design phases. The results also highlight the importance of multidisciplinary and user-centred teams that can enhance collaboration and communication during the design processes.

  5. Loudspeaker Design and Performance Evaluation

    Science.gov (United States)

    Mäkivirta, Aki Vihtori

    A loudspeaker comprises transducers converting an electrical driving signal into sound pressure, an enclosure working as a holder for transducers, front baffle and box to contain and eliminate the rear-radiating audio signal, and electronic components. Modeling of transducers as well as enclosures is treated in Chap. 32 of this handbook. The purpose of the present chapter is to shed light on the design choices and options for the electronic circuits conditioning the electrical signal fed into loudspeaker transducers in order to optimize the acoustic performance of the loudspeaker.

  6. Stereoscopic game design and evaluation

    Science.gov (United States)

    Rivett, Joe; Holliman, Nicolas

    2013-03-01

    We report on a new game design where the goal is to make the stereoscopic depth cue sufficiently critical to success that game play should become impossible without using a stereoscopic 3D (S3D) display and, at the same time, we investigate whether S3D game play is affected by screen size. Before we detail our new game design we review previously unreported results from our stereoscopic game research over the last ten years at the Durham Visualisation Laboratory. This demonstrates that game players can achieve significantly higher scores using S3D displays when depth judgements are an integral part of the game. Method: We design a game where almost all depth cues, apart from the binocular cue, are removed. The aim of the game is to steer a spaceship through a series of oncoming hoops where the viewpoint of the game player is from above, with the hoops moving right to left across the screen towards the spaceship, to play the game it is essential to make decisive depth judgments to steer the spaceship through each oncoming hoop. To confound these judgements we design altered depth cues, for example perspective is reduced as a cue by varying the hoop's depth, radius and cross-sectional size. Results: Players were screened for stereoscopic vision, given a short practice session, and then played the game in both 2D and S3D modes on a seventeen inch desktop display, on average participants achieved a more than three times higher score in S3D than they achieved in 2D. The same experiment was repeated using a four metre S3D projection screen and similar results were found. Conclusions: Our conclusion is that games that use the binocular depth cue in decisive game judgements can benefit significantly from using an S3D display. Based on both our current and previous results we additionally conclude that display size, from cell-phone, to desktop, to projection display does not adversely affect player performance.

  7. HTGR fuel particle crusher design evaluation

    International Nuclear Information System (INIS)

    Johanson, N.W.

    1978-10-01

    This report describes an evaluation of the design of the existing engineering-scale fuel particle crushing system for the HTGR reprocessing cold pilot plant at General Atomic Company (GA). The purpose of this evaluation is to assess the suitability of the existing design as a prototype of the HTGR Recycle Reference Facility (HRRF) particle crushing system and to recommend alternatives where the existing design is thought to be unsuitable as a prototype. This evaluation has led to recommendations for an upgraded design incorporating improvements in bearing and seal arrangement, housing construction, and control of roll gap thermal expansion. 23 figures, 6 tables

  8. Design evaluation of emergency core cooling systems using Axiomatic Design

    Energy Technology Data Exchange (ETDEWEB)

    Heo, Gyunyoung [Massachusetts Institute of Technology, Department of Mechanical Engineering, 77 Massachusetts Avenue, Cambridge, MA 02139 (United States)]. E-mail: gheo@mit.edu; Lee, Song Kyu [Korea Advanced Institute of Science and Technology, Department of Nuclear and Quantum Engineering, 373-1 Guseong-dong, Yuseong-gu, Daejeon (Korea, Republic of)

    2007-01-15

    In designing nuclear power plants (NPPs), the evaluation of safety is one of the important issues. As a measure for evaluating safety, this paper proposes a methodology to examine the design process of emergency core cooling systems (ECCSs) in NPPs using Axiomatic Design (AD). This is particularly important for identifying vulnerabilities and creating solutions. Korean Advanced Power Reactor 1400 MWe (APR1400) adopted the ECCS, which was improved to meet the stronger safety regulations than that of the current Optimized Power Reactor 1000 MWe (OPR1000). To improve the performance and safety of the ECCS, the various design strategies such as independency or redundancy were implemented, and their effectiveness was confirmed by calculating core damage frequency. We suggest an alternative viewpoint of evaluating the deployment of design strategies in terms of AD methodology. AD suggests two design principles and the visualization tools for organizing design process. The important benefit of AD is that it is capable of providing suitable priorities for deploying design strategies. The reverse engineering driven by AD has been able to show that the design process of the ECCS of APR1400 was improved in comparison to that of OPR1000 from the viewpoint of the coordination of design strategies.

  9. Interactions between the Design and Operation of Shale Gas Networks, Including CO2 Sequestration

    Directory of Open Access Journals (Sweden)

    Sharifzadeh Mahdi

    2017-04-01

    Full Text Available As the demand for energy continues to increase, shale gas, as an unconventional source of methane (CH4, shows great potential for commercialization. However, due to the ultra-low permeability of shale gas reservoirs, special procedures such as horizontal drilling, hydraulic fracturing, periodic well shut-in, and carbon dioxide (CO2 injection may be required in order to boost gas production, maximize economic benefits, and ensure safe and environmentally sound operation. Although intensive research is devoted to this emerging technology, many researchers have studied shale gas design and operational decisions only in isolation. In fact, these decisions are highly interactive and should be considered simultaneously. Therefore, the research question addressed in this study includes interactions between design and operational decisions. In this paper, we first establish a full-physics model for a shale gas reservoir. Next, we conduct a sensitivity analysis of important design and operational decisions such as well length, well arrangement, number of fractures, fracture distance, CO2 injection rate, and shut-in scheduling in order to gain in-depth insights into the complex behavior of shale gas networks. The results suggest that the case with the highest shale gas production may not necessarily be the most profitable design; and that drilling, fracturing, and CO2 injection have great impacts on the economic viability of this technology. In particular, due to the high costs, enhanced gas recovery (EGR using CO2 does not appear to be commercially competitive, unless tax abatements or subsidies are available for CO2 sequestration. It was also found that the interactions between design and operational decisions are significant and that these decisions should be optimized simultaneously.

  10. Educational Videogames: Concept, Design And Evaluation

    Science.gov (United States)

    Rohrlick, D.; Yang, A.; Kilb, D. L.; Ma, L.; Ruzic, R.; Peach, C. L.; Layman, C. C.

    2013-12-01

    Videogames have historically gained popularity thanks to their entertainment rather than their educational value. This may be due, in part, to the fact that many educational videogames present academic concepts in dry, quiz-like ways, without the visual experiences, interactivity, and excitement of non-educational games. The increasing availability of tools that allow designers to easily create rich experiences for players now makes it simpler than ever for educational game designers to generate the visual experiences, interactivity, and excitement that gamers have grown to expect. Based on data from our work, when designed effectively, educational games can engage players, teach concepts, and tear down the stereotype of the stuffy, boring educational game. Our team has been experimenting with different ways to present scientific and mathematical concepts to middle and high school students through engaging, interactive games. When designing a gameplay concept, we focus on what we want the player to learn and experience as well as how to maintain a learning environment that is fun and engaging. Techniques that we have found successful include the use of a series of fast-paced 'minigames,' and the use of a 'simulator' learning method that allows a player to learn by completing objectives similar to those completed by today's scientists. Formative evaluations of our games over the past year have revealed both design strengths and weaknesses. Based on findings from a systematic evaluation of game play with diverse groups, with data collected through in-person observations of game play, knowledge assessments, focus groups, interviews with players, and computer tracking of students' game play behavior, we have found that players are uniformly enthusiastic about the educational tools. At the same time, we find there is more work to be done to make our tools fully intuitive, and to effectively present complex mathematical and scientific concepts to learners from a wide

  11. Recommended Resources for Planning to Evaluate Program Improvement Efforts (Including the SSIP)

    Science.gov (United States)

    National Center for Systemic Improvement at WestEd, 2015

    2015-01-01

    This document provides a list of recommended existing resources for state Part C and Part B 619 staff and technical assistance (TA) providers to utilize to support evaluation planning for program improvement efforts (including the State Systemic Improvement Plan, SSIP). There are many resources available related to evaluation and evaluation…

  12. Three-dimensional cross point readout detector design for including depth information

    Science.gov (United States)

    Lee, Seung-Jae; Baek, Cheol-Ha

    2018-04-01

    We designed a depth-encoding positron emission tomography (PET) detector using a cross point readout method with wavelength-shifting (WLS) fibers. To evaluate the characteristics of the novel detector module and the PET system, we used the DETECT2000 to perform optical photon transport in the crystal array. The GATE was also used. The detector module is made up of four layers of scintillator arrays, the five layers of WLS fiber arrays, and two sensor arrays. The WLS fiber arrays in each layer cross each other to transport light to each sensor array. The two sensor arrays are coupled to the forward and left sides of the WLS fiber array, respectively. The identification of three-dimensional pixels was determined using a digital positioning algorithm. All pixels were well decoded, with the system resolution ranging from 2.11 mm to 2.29 mm at full width at half maximum (FWHM).

  13. Evaluation of Interactive Website Design Indicators for e-Entrepreneurship

    OpenAIRE

    Chih-Chao Chung; Li-Chung Chao; Chin-Hui Chen; Shi-Jer Lou

    2016-01-01

    Using an analytic network process (ANP) as an analytical tool, this study aims to construct an ANP evaluation model of interactive website design indicators. Through a review of the literature, interactive website design of e-entrepreneurship is generalized to the following dimensions: (1) Design; (2) Checking; (3) Service; (4) Interactive; and (5) Promotion, including 19 design indicators. The research is conducted for a case company. According to the findings, the model helps the case compa...

  14. Software for Evaluation of Conceptual Design

    DEFF Research Database (Denmark)

    Hartvig, Susanne C

    1998-01-01

    by the prototype, it addresses the requirements that the methods imply, and it explains the actual implementation of the prototype. Finally it discusses what have been learned from developing and testing the prototype. In this paper it is suggested, that a software tool which supports evaluation of design can...... be developed with a limited effort, and that such tools could support a structured evaluation process as opposed to no evaluation. Compared to manual evaluation, the introduced software based evaluation tool offers automation of tasks, such as performing assessments, when they are based on prior evaluations...

  15. Including alternative resources in state renewable portfolio standards: Current design and implementation experience

    International Nuclear Information System (INIS)

    Heeter, Jenny; Bird, Lori

    2013-01-01

    As of October 2012, 29 states, the District of Columbia, and Puerto Rico have instituted a renewable portfolio standard (RPS). Each state policy is unique, varying in percentage targets, timetables, and eligible resources. Increasingly, new RPS polices have included alternative resources. Alternative resources have included energy efficiency, thermal resources, and, to a lesser extent, non-renewables. This paper examines state experience with implementing renewable portfolio standards that include energy efficiency, thermal resources, and non-renewable energy and explores compliance experience, costs, and how states evaluate, measure, and verify energy efficiency and convert thermal energy. It aims to gain insights from the experience of states for possible federal clean energy policy as well as to share experience and lessons for state RPS implementation. - Highlights: • Increasingly, new RPS policies have included alternative resources. • Nearly all states provide a separate tier or cap on the quantity of eligible alternative resources. • Where allowed, non-renewables and energy efficiency are being heavily utilized

  16. Evaluation of design parameters of eight dental implant designs: A ...

    African Journals Online (AJOL)

    Aim: Implants could be considered predictable tools for replacing missing teeth or teeth that are irrational to treat. Implant macrodesign includes thread, body shape and thread design. Implant threads should be designed to maximize the delivery of optimal favorable stresses. The aim of this finite element model study was to ...

  17. Scaling Research Results: Design and Evaluation | IDRC ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Design and evaluation The project will provide helpful guidance to IDRC management and ... scaling and programming for scalable research Offer the monograph in multiple forms, ... Asian outlook: New growth dependent on new productivity.

  18. Modelling of Water Cooled Fuel Including Design Basis and Severe Accidents. Proceedings of a Technical Meeting

    International Nuclear Information System (INIS)

    2015-11-01

    The demands on nuclear fuel have recently been increasing, and include transient regimes, higher discharge burnup and longer fuel cycles. This has resulted in an increase of loads on fuel and core internals. In order to satisfy these demands while ensuring compliance with safety criteria, new national and international programmes have been launched and advanced modelling codes are being developed. The Fukushima Daiichi accident has particularly demonstrated the need for adequate analysis of all aspects of fuel performance to prevent a failure and also to predict fuel behaviour were an accident to occur.This publication presents the Proceedings of the Technical Meeting on Modelling of Water Cooled Fuel Including Design Basis and Severe Accidents, which was hosted by the Nuclear Power Institute of China (NPIC) in Chengdu, China, following the recommendation made in 2013 at the IAEA Technical Working Group on Fuel Performance and Technology. This recommendation was in agreement with IAEA mid-term initiatives, linked to the post-Fukushima IAEA Nuclear Safety Action Plan, as well as the forthcoming Coordinated Research Project (CRP) on Fuel Modelling in Accident Conditions. At the technical meeting in Chengdu, major areas and physical phenomena, as well as types of code and experiment to be studied and used in the CRP, were discussed. The technical meeting provided a forum for international experts to review the state of the art of code development for modelling fuel performance of nuclear fuel for water cooled reactors with regard to steady state and transient conditions, and for design basis and early phases of severe accidents, including experimental support for code validation. A round table discussion focused on the needs and perspectives on fuel modelling in accident conditions. This meeting was the ninth in a series of IAEA meetings, which reflects Member States’ continuing interest in nuclear fuel issues. The previous meetings were held in 1980 (jointly with

  19. New tools for evaluating LQAS survey designs

    OpenAIRE

    Hund, Lauren

    2014-01-01

    Lot Quality Assurance Sampling (LQAS) surveys have become increasingly popular in global health care applications. Incorporating Bayesian ideas into LQAS survey design, such as using reasonable prior beliefs about the distribution of an indicator, can improve the selection of design parameters and decision rules. In this paper, a joint frequentist and Bayesian framework is proposed for evaluating LQAS classification accuracy and informing survey design parameters. Simple software tools are pr...

  20. Evaluation of urban river landscape design rationality based on AHP

    Directory of Open Access Journals (Sweden)

    Qiao Lifang

    2008-12-01

    Full Text Available An evaluation model for the rationality of the landscape design of urban rivers was established with the analytic hierarchy process (AHP method so as to provide a foundation for updating the landscape design of urban rivers. The evaluation system was divided into four layers, including the target layer, the comprehensive layer, the element layer, and the index layer. Each layer was made of different indices. The evaluation standards for each index were also given in this paper. This evaluation model was proved tenable through its application to the landscape design rationality evaluation of the Weihe River in Xinxiang City of Henan Province. The results show that the water quality, space, activity, facility, community, width of vegetation, sense of beauty and water content are among the most influential factors and should be considered the main basis for evaluating the rationality of the landscape design of urban rivers.

  1. Including Alternative Resources in State Renewable Portfolio Standards: Current Design and Implementation Experience

    Energy Technology Data Exchange (ETDEWEB)

    Heeter, J.; Bird, L.

    2012-11-01

    Currently, 29 states, the District of Columbia, and Puerto Rico have instituted a renewable portfolio standard (RPS). An RPS sets a minimum threshold for how much renewable energy must be generated in a given year. Each state policy is unique, varying in percentage targets, timetables, and eligible resources. This paper examines state experience with implementing renewable portfolio standards that include energy efficiency, thermal resources, and non-renewable energy and explores compliance experience, costs, and how states evaluate, measure, and verify energy efficiency and convert thermal energy. It aims to gain insights from the experience of states for possible federal clean energy policy as well as to share experience and lessons for state RPS implementation.

  2. Designing evaluation of learning in outline courses

    Directory of Open Access Journals (Sweden)

    Estévez, Orosmán V.

    2010-07-01

    Full Text Available This paper is intended to characterize the evaluation process of online courses from the perspectives of several scholars who are currently conducting research on the topic. The importance of an integral diagnosis and the interconnections between diagnosis, learning activities design and evaluation are outlined. The study leads the authors to the conclusion that evaluation in online courses in Cuba demands a thorough scientific research so as to go deeper into its characterizing features.

  3. Designer's requirements for evaluation of sustainability

    DEFF Research Database (Denmark)

    Bey, Niki; Lenau, Torben Anker

    1998-01-01

    Today, sustainability of products is often evaluated on the basis of assessments of their environmental performance. Established means for this purpose are formal Life Cycle Assessment (LCA) methods. Designers have an essential influence on product design and are therefore one target group for life...... cycle-based evaluation methods. However, the application of LCA in the design process, when for example different materials and manufacturing processes have to be selected, is difficult. This is, among other things, because only a few designers have a deeper background in this area and even simplified...... LCAs involve calculations with a relatively high accuracy. Most LCA methods do therefore not qualify as hands-on tool for utilisation by typical designers.In this context, the authors raise the question, whether a largely simplified LCA-method which is exclusively based on energy considerations can...

  4. Contract Design: Risk Management and Evaluation.

    Science.gov (United States)

    Mühlbacher, Axel C; Amelung, Volker E; Juhnke, Christin

    2018-01-12

    Effective risk adjustment is an aspect that is more and more given weight on the background of competitive health insurance systems and vital healthcare systems. The risk structure of the providers plays a vital role in Pay for Performance. A prerequisite for optimal incentive-based service models is a (partial) dependence of the agent's returns on the provider's gain level. Integrated care systems as well as accountable care organisations (ACOs) in the US and similar concepts in other countries are advocated as an effective method of improving the performance of healthcare systems. These systems outline a payment and care delivery model that intends to tie provider reimbursements to predefined quality metrics. By this the total costs of care shall be reduced. Little is known about the contractual design and the main challenges of delegating "accountability" to these new kinds of organisations and/or contracts. The costs of market utilisation are highly relevant for the conception of healthcare contracts; furthermore information asymmetries and contract-specific investments are an obstacle to the efficient operation of ACOs. A comprehensive literature review on methods of designing contracts in Integrated Care was conducted. The research question in this article focuses on how reimbursement strategies, evaluation of measures and methods of risk adjustment can best be integrated in healthcare contracting. Each integrated care contract includes challenges for both payers and providers without having sufficient empirical data on both sides. These challenges are clinical, administrative or financial nature. Risk adjusted contracts ensure that the reimbursement roughly matches the true costs resulting from the morbidity of a population. If reimbursement of care provider corresponds to the actual expenses for an individual/population the problem of risk selection is greatly reduced. The currently used methods of risk adjustment have widely differing model and forecast

  5. Contract Design: Risk Management and Evaluation

    Directory of Open Access Journals (Sweden)

    Axel C. Mühlbacher

    2018-01-01

    Full Text Available Introduction: Effective risk adjustment is an aspect that is more and more given weight on the background of competitive health insurance systems and vital healthcare systems. The risk structure of the providers plays a vital role in Pay for Performance. A prerequisite for optimal incentive-based service models is a (partial dependence of the agent’s returns on the provider’s gain level. Integrated care systems as well as accountable care organisations (ACOs in the US and similar concepts in other countries are advocated as an effective method of improving the performance of healthcare systems. These systems outline a payment and care delivery model that intends to tie provider reimbursements to predefined quality metrics. By this the total costs of care shall be reduced.  Methods: Little is known about the contractual design and the main challenges of delegating “accountability” to these new kinds of organisations and/or contracts. The costs of market utilisation are highly relevant for the conception of healthcare contracts; furthermore information asymmetries and contract-specific investments are an obstacle to the efficient operation of ACOs. A comprehensive literature review on methods of designing contracts in Integrated Care was conducted. The research question in this article focuses on how reimbursement strategies, evaluation of measures and methods of risk adjustment can best be integrated in healthcare contracting.  Results: Each integrated care contract includes challenges for both payers and providers without having sufficient empirical data on both sides. These challenges are clinical, administrative or financial nature. Risk adjusted contracts ensure that the reimbursement roughly matches the true costs resulting from the morbidity of a population. If reimbursement of care provider corresponds to the actual expenses for an individual/population the problem of risk selection is greatly reduced. The currently used methods

  6. Optimal Design and Real Time Implementation of Autonomous Microgrid Including Active Load

    Directory of Open Access Journals (Sweden)

    Mohamed A. Hassan

    2018-05-01

    Full Text Available Controller gains and power-sharing parameters are the main parameters affect the dynamic performance of the microgrid. Considering an active load to the autonomous microgrid, the stability problem will be more involved. In this paper, the active load effect on microgrid dynamic stability is explored. An autonomous microgrid including three inverter-based distributed generations (DGs with an active load is modeled and the associated controllers are designed. Controller gains of the inverters and active load as well as Phase Locked Loop (PLL parameters are optimally tuned to guarantee overall system stability. A weighted objective function is proposed to minimize the error in both measured active power and DC voltage based on time-domain simulations. Different AC and DC disturbances are applied to verify and assess the effectiveness of the proposed control strategy. The results demonstrate the potential of the proposed controller to enhance the microgrid stability and to provide efficient damping characteristics. Additionally, the proposed controller is compared with the literature to demonstrate its superiority. Finally, the microgrid considered has been established and implemented on real time digital simulator (RTDS. The experimental results validate the simulation results and approve the effectiveness of the proposed controllers to enrich the stability of the considered microgrid.

  7. Peer assessment in university teaching: Evaluating seven course designs

    OpenAIRE

    van den Berg, I.; Admiraal, W.; Pilot, A.

    2006-01-01

    Peer assessment in university teaching: evaluating seven course designs Abstract Peer assessment is understood to be an arrangement with students assessing the quality of their fellow students’ writings and giving feedback to each other. This multiple-case study of seven designs of peer assessment focuses on the contribution of peer assessment to the acquisition of undergraduates’ writing skills. Its aim is to arrive at an optimal design of peer assessment. Factors included in this study are:...

  8. An integrated optimum design approach for high speed prop-rotors including acoustic constraints

    Science.gov (United States)

    Chattopadhyay, Aditi; Wells, Valana; Mccarthy, Thomas; Han, Arris

    1993-01-01

    The objective of this research is to develop optimization procedures to provide design trends in high speed prop-rotors. The necessary disciplinary couplings are all considered within a closed loop multilevel decomposition optimization process. The procedures involve the consideration of blade-aeroelastic aerodynamic performance, structural-dynamic design requirements, and acoustics. Further, since the design involves consideration of several different objective functions, multiobjective function formulation techniques are developed.

  9. When users can´t be included in inclusive design

    DEFF Research Database (Denmark)

    Herriott, Richard

    2012-01-01

    and disabled users make the need for useability and pleasurability even more important since alternative products are comparatively few. This paper examines the workarounds two teams of designers have used to reduce the demands placed on emphysema patients and elderly users during inclusive design processes......Inclusive Design (ID) methods place a strong emphasis on user participation in designing mainstream products. In recent years researchers in the field of assistive technology (AT) have drawn on and contributed to the ID approach. There are good grounds for this association. However, the linkage...

  10. BALANCED SCORECARDS EVALUATION MODEL THAT INCLUDES ELEMENTS OF ENVIRONMENTAL MANAGEMENT SYSTEM USING AHP MODEL

    Directory of Open Access Journals (Sweden)

    Jelena Jovanović

    2010-03-01

    Full Text Available The research is oriented on improvement of environmental management system (EMS using BSC (Balanced Scorecard model that presents strategic model of measurem ents and improvement of organisational performance. The research will present approach of objectives and environmental management me trics involvement (proposed by literature review in conventional BSC in "Ad Barska plovi dba" organisation. Further we will test creation of ECO-BSC model based on business activities of non-profit organisations in order to improve envir onmental management system in parallel with other systems of management. Using this approach we may obtain 4 models of BSC that includ es elements of environmen tal management system for AD "Barska plovidba". Taking into acc ount that implementation and evaluation need long period of time in AD "Barska plovidba", the final choice will be based on 14598 (Information technology - Software product evaluation and ISO 9126 (Software engineering - Product quality using AHP method. Those standards are usually used for evaluation of quality software product and computer programs that serve in organisation as support and factors for development. So, AHP model will be bas ed on evolution criteria based on suggestion of ISO 9126 standards and types of evaluation from two evaluation teams. Members of team & will be experts in BSC and environmental management system that are not em ployed in AD "Barska Plovidba" organisation. The members of team 2 will be managers of AD "Barska Plovidba" organisation (including manage rs from environmental department. Merging results based on previously cr eated two AHP models, one can obtain the most appropriate BSC that includes elements of environmental management system. The chosen model will present at the same time suggestion for approach choice including ecological metrics in conventional BSC model for firm that has at least one ECO strategic orientation.

  11. Evaluation criteria for spectral design of camouflage

    Science.gov (United States)

    Škerlind, Christina; Fagerström, Jan; Hallberg, Tomas; Kariis, Hans

    2015-10-01

    In development of visual (VIS) and infrared (IR) camouflage for signature management, the aim is the design of surface properties of an object to spectrally match or adapt to a background and thereby minimizing the contrast perceived by a threatening sensor. The so called 'ladder model" relates the requirements for task measure of effectiveness with surface structure properties through the steps signature effectiveness and object signature. It is intended to link materials properties via platform signature to military utility and vice versa. Spectral design of a surface intends to give it a desired wavelength dependent optical response to fit a specific application of interest. Six evaluation criteria were stated, with the aim to aid the process to put requirement on camouflage and for evaluation. The six criteria correspond to properties such as reflectance, gloss, emissivity, and degree of polarization as well as dynamic properties, and broadband or multispectral properties. These criteria have previously been exemplified on different kinds of materials and investigated separately. Anderson and Åkerlind further point out that the six criteria rarely were considered or described all together in one and same publication previously. The specific level of requirement of the different properties must be specified individually for each specific situation and environment to minimize the contrast between target and a background. The criteria or properties are not totally independent of one another. How they are correlated is part of the theme of this paper. However, prioritization has been made due to the limit of space. Therefore all of the interconnections between the six criteria will not be considered in the work of this report. The ladder step previous to digging into the different material composition possibilities and choice of suitable materials and structures (not covered here), includes the object signature and decision of what the spectral response should be

  12. Combinatorial evaluation of systems including decomposition of a system representation into fundamental cycles

    Science.gov (United States)

    Oliveira, Joseph S [Richland, WA; Jones-Oliveira, Janet B [Richland, WA; Bailey, Colin G [Wellington, NZ; Gull, Dean W [Seattle, WA

    2008-07-01

    One embodiment of the present invention includes a computer operable to represent a physical system with a graphical data structure corresponding to a matroid. The graphical data structure corresponds to a number of vertices and a number of edges that each correspond to two of the vertices. The computer is further operable to define a closed pathway arrangement with the graphical data structure and identify each different one of a number of fundamental cycles by evaluating a different respective one of the edges with a spanning tree representation. The fundamental cycles each include three or more of the vertices.

  13. Multinational Design Evaluation Programme (MDEP) - Safety Goals

    International Nuclear Information System (INIS)

    Vaughan, G.J.

    2011-01-01

    One of the aims of the NEA's Multinational Design Evaluation Programme (MDEP) is to work towards greater harmonisation of regulatory requirements. To achieve this aim, it is necessary that there is a degree of convergence on the safety goals that are required to be met by designers and operators. The term 'safety goals' is defined to cover all health and safety requirements which must be met: these may be deterministic rules and/or probabilistic targets. They should cover the safety of workers, public and the environment in line with the IAEA's Basic Safety Objective; encompassing safety in normal operation through to severe accidents. MDEP is also interested in how its work can be extended to future reactors, which may use significantly different technology to the almost ubiquitous LWRs used today and in the next generation, building on the close co-operation within MDEP between the regulators who are currently engaged in constructing or carrying out design reviews on new designs. For two designs this work has involved several regulators sharing their safety assessments and in some cases issuing statements on issues that need to be addressed. Work is also progressing towards joint regulatory position statements on specific assessment areas. Harmonisation of safety goals will enhance the cooperation between regulators as further developments in design and technology occur. All regulators have safety goals, but these are expressed in many different ways and exercises in comparing them frequently are done at a very low level eg specific temperatures in the reactor vessel of a specific reactor type. The differences in the requirements from different regulators are difficult to resolve as the goals are derived using different principles and assumptions and are often for a specific technology. Therefore a different approach is being investigated, starting with the top-level safety goals and try to derive a structure and means of deriving lower tier

  14. Evaluation of technical design of advanced information display(III)

    International Nuclear Information System (INIS)

    Cha, Woo Chang; Jung, Sung Hae; Park, Joon Yong; Kim, Nam Cheol; Park, Soon Hyuk

    2005-02-01

    As the computer technology is highly developed, the mental model of computer users including NPP operators has been changed from analogue display type-based stereotype to digitalized one. Therefore, it is necessary and confident to consider the issues to evaluate system suitability of advanced information display on visual display terminal. This document is intended for providing an updated and expanded set of user-interface guidelines that meet the needs of designing digitalized information display by finding the generic guidelines involving information display design issues, and the relationship among the guidelines. The design issues and resolutions from the finding may provide the cues for the designers and evaluators of the specific man machine interfaces of digitalized devices. The Design Review Supporting System for Advanced Information Display(DReSS-AID) was developed for the practical usage of evaluators-in-field, which was implemented with Hangul version guidelines

  15. Evaluation of technical design of advanced information display(III)

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Woo Chang; Jung, Sung Hae; Park, Joon Yong; Kim, Nam Cheol [Kumoh National Institute of Technology, Gumi (Korea, Republic of); Park, Soon Hyuk [DNT Inc., Daejeon (Korea, Republic of)

    2005-02-15

    As the computer technology is highly developed, the mental model of computer users including NPP operators has been changed from analogue display type-based stereotype to digitalized one. Therefore, it is necessary and confident to consider the issues to evaluate system suitability of advanced information display on visual display terminal. This document is intended for providing an updated and expanded set of user-interface guidelines that meet the needs of designing digitalized information display by finding the generic guidelines involving information display design issues, and the relationship among the guidelines. The design issues and resolutions from the finding may provide the cues for the designers and evaluators of the specific man machine interfaces of digitalized devices. The Design Review Supporting System for Advanced Information Display(DReSS-AID) was developed for the practical usage of evaluators-in-field, which was implemented with Hangul version guidelines.

  16. Nuclear waste glass melter design including the power and control systems

    International Nuclear Information System (INIS)

    Chapman, C.C.

    1982-01-01

    An energy balance of a joule-heated nuclear waste glass melter is used to discuss the problems in the design of the melter geometry and in the specifications of the power and control systems. The relationships between geometry, electrode current density, production rate, load voltage, and load power are presented graphically. The influence of liquid feeding on the surface of the glass and the variability of nuclear waste glass on the design and control during operation is discussed. 10 refs

  17. Modified Design of Hydroturbine Wicket Gates to Include Liquid Control Jets

    Science.gov (United States)

    Lewis, Bryan; Cimbala, John; Wouden, Alex

    2013-11-01

    With the ever-increasing penetration of alternative electricity generation, it is becoming more common to operate hydroturbines under off-design conditions in order to maintain stability in the electric power grid. Improving the off-design performance of these turbines is therefore of significant importance. As the runner blades of a Francis hydroturbine pass though the wakes created by the upstream guide vanes (wicket gates and stay vanes), they experience significant changes in the instantaneous values of absolute velocity, flow angle, and pressure. The concept of adding water jets to the trailing edge of the guide vanes is proposed as a method for reducing the dynamic load on the hydroturbine runner blades, as well as modifying the flow angle of the water entering the runner to improve turbine efficiency during off-design operation. In order to add water jets that are capable of turning the flow, a modified beveled trailing edge design is presented. Computational experiments show that a +/-5° change in swirl angle is achievable with the new design, as well as up to 4% improvement in turbine efficiency during off-design operation. This correlates to an overall improvement in machine efficiency of up to 2%, when the losses through the jet channels are taken into account. Funding for this work was provided by the DOD, through the National Defense Science and Engineering Graduate (NDSEG) Fellowship, and the DOE, through the Penn State Hydropower Research Grant.

  18. Including α s1 casein gene information in genomic evaluations of French dairy goats.

    Science.gov (United States)

    Carillier-Jacquin, Céline; Larroque, Hélène; Robert-Granié, Christèle

    2016-08-04

    Genomic best linear unbiased prediction methods assume that all markers explain the same fraction of the genetic variance and do not account effectively for genes with major effects such as the α s1 casein polymorphism in dairy goats. In this study, we investigated methods to include the available α s1 casein genotype effect in genomic evaluations of French dairy goats. First, the α s1 casein genotype was included as a fixed effect in genomic evaluation models based only on bucks that were genotyped at the α s1 casein locus. Less than 1 % of the females with phenotypes were genotyped at the α s1 casein gene. Thus, to incorporate these female phenotypes in the genomic evaluation, two methods that allowed for this large number of missing α s1 casein genotypes were investigated. Probabilities for each possible α s1 casein genotype were first estimated for each female of unknown genotype based on iterative peeling equations. The second method is based on a multiallelic gene content approach. For each model tested, we used three datasets each divided into a training and a validation set: (1) two-breed population (Alpine + Saanen), (2) Alpine population, and (3) Saanen population. The α s1 casein genotype had a significant effect on milk yield, fat content and protein content. Including an α s1 casein effect in genetic and genomic evaluations based only on male known α s1 casein genotypes improved accuracies (from 6 to 27 %). In genomic evaluations based on all female phenotypes, the gene content approach performed better than the other tested methods but the improvement in accuracy was only slightly better (from 1 to 14 %) than that of a genomic model without the α s1 casein effect. Including the α s1 casein effect in a genomic evaluation model for French dairy goats is possible and useful to improve accuracy. Difficulties in predicting the genotypes for ungenotyped animals limited the improvement in accuracy of the obtained estimated breeding values.

  19. Design optimization of transformerless grid-connected PV inverters including reliability

    DEFF Research Database (Denmark)

    Koutroulis, Eftichios; Blaabjerg, Frede

    2012-01-01

    Of the Electricity (LCOE) generated during the PV system lifetime period is minimized. The LCOE is calculated also considering the failure rates of the components, which affect the reliability performance and lifetime maintenance cost of the PV inverter. A design example is presented, demonstrating that compared...... to the non-optimized PV inverter structures, the PV inverters designed using the proposed optimization methodology exhibit lower total manufacturing and lifetime maintenance cost and inject more energy into the electric-grid and by that minimizing LCOE.......This paper presents a new methodology for optimal design of transformerless Photovoltaic (PV) inverters targeting a cost-effective deployment of grid-connected PV systems. The optimal values and types of the PV inverter components are calculated such that the PV inverter Levelized Cost...

  20. Design Optimization of Transformerless Grid-Connected PV Inverters Including Reliability

    DEFF Research Database (Denmark)

    Koutroulis, Eftichios; Blaabjerg, Frede

    2013-01-01

    such that the PV inverter LCOE generated during the PV system lifetime period is minimized. The LCOE is also calculated considering the failure rates of the components, which affect the reliability performance and lifetime maintenance cost of the PV inverter. A design example is presented, demonstrating...... that compared to the nonoptimized PV inverter structures, the PV inverters designed using the proposed optimization methodology exhibit lower total manufacturing and lifetime maintenance cost and inject more energy into the electric-grid and by that minimizing LCOE.......This paper presents a new methodology for optimal design of transformerless photovoltaic (PV) inverters targeting a cost-effective deployment of grid-connected PV systems. The optimal switching frequency as well as the optimal values and types of the PV inverter components is calculated...

  1. Design and construction of a photobioreactor for hydrogen production, including status in the field.

    Science.gov (United States)

    Skjånes, Kari; Andersen, Uno; Heidorn, Thorsten; Borgvang, Stig A

    Several species of microalgae and phototrophic bacteria are able to produce hydrogen under certain conditions. A range of different photobioreactor systems have been used by different research groups for lab-scale hydrogen production experiments, and some few attempts have been made to upscale the hydrogen production process. Even though a photobioreactor system for hydrogen production does require special construction properties (e.g., hydrogen tight, mixing by other means than bubbling with air), only very few attempts have been made to design photobioreactors specifically for the purpose of hydrogen production. We have constructed a flat panel photobioreactor system that can be used in two modes: either for the cultivation of phototrophic microorganisms (upright and bubbling) or for the production of hydrogen or other anaerobic products (mixing by "rocking motion"). Special emphasis has been taken to avoid any hydrogen leakages, both by means of constructional and material choices. The flat plate photobioreactor system is controlled by a custom-built control system that can log and control temperature, pH, and optical density and additionally log the amount of produced gas and dissolved oxygen concentration. This paper summarizes the status in the field of photobioreactors for hydrogen production and describes in detail the design and construction of a purpose-built flat panel photobioreactor system, optimized for hydrogen production in terms of structural functionality, durability, performance, and selection of materials. The motivations for the choices made during the design process and advantages/disadvantages of previous designs are discussed.

  2. Evaluation of Frameworks for HSCT Design Optimization

    Science.gov (United States)

    Krishnan, Ramki

    1998-01-01

    This report is an evaluation of engineering frameworks that could be used to augment, supplement, or replace the existing FIDO 3.5 (Framework for Interdisciplinary Design and Optimization Version 3.5) framework. The report begins with the motivation for this effort, followed by a description of an "ideal" multidisciplinary design and optimization (MDO) framework. The discussion then turns to how each candidate framework stacks up against this ideal. This report ends with recommendations as to the "best" frameworks that should be down-selected for detailed review.

  3. Cockpit design and evaluation using interactive graphics

    Science.gov (United States)

    Evans, S. M.

    1975-01-01

    A general overview of the characteristics of an interactive graphics system which was developed to assist cockpit engineers design and evaluate work stations was presented. The manikin used in this COMputerized BIomechanical MAN-model (COMBIMAN) was described, as are provisions for generating work stations and assessing interactions between man and environment. The applications of the present system are explained, and critiques of COMBIMAN are presented. The limitations of the existing programs and the requirements of the designers necessitate future revisions and additions to the biomechanical and erogonomic properties of COMBIMAN. Some of these enhancements are discussed.

  4. Evaluation report(1): on design criteria for KALIMER metal fuel

    Energy Technology Data Exchange (ETDEWEB)

    Hwang, Woan; Lee, Byoung Oon; Kim, Young Il

    2001-04-01

    Fuel rods, assembly ducts and their components in KALIMER should be designed to maintain the integrities and to assure their reliable in-reactor performances under the steady state and operational transient conditions which are included in design basis category. And the fuel system must be designed with enough engineering margin to minimize and prevent the failures under ab-normal operational condition, like an accident.In this report, some design limits and the criteria for the fuel assembly ducts for KALIMER are driven by evaluating the irradiation data of metallic fuel based on experimental data from ANL in USA, CRIEPI in Japan and RIAR in Russia.

  5. Evaluation report(1): on design criteria for KALIMER metal fuel

    International Nuclear Information System (INIS)

    Hwang, Woan; Lee, Byoung Oon; Kim, Young Il

    2001-04-01

    Fuel rods, assembly ducts and their components in KALIMER should be designed to maintain the integrities and to assure their reliable in-reactor performances under the steady state and operational transient conditions which are included in design basis category. And the fuel system must be designed with enough engineering margin to minimize and prevent the failures under ab-normal operational condition, like an accident.In this report, some design limits and the criteria for the fuel assembly ducts for KALIMER are driven by evaluating the irradiation data of metallic fuel based on experimental data from ANL in USA, CRIEPI in Japan and RIAR in Russia

  6. Design Optimization of Transformerless Grid-Connected PV Inverters Including Reliability

    OpenAIRE

    Koutroulis, Eftichios; Blaabjerg, Frede

    2013-01-01

    This paper presents a new methodology for optimal design of transformerless photovoltaic (PV) inverters targeting a cost-effective deployment of grid-connected PV systems. The optimal switching frequency as well as the optimal values and types of the PV inverter components is calculated such that the PV inverter LCOE generated during the PV system lifetime period is minimized. The LCOE is also calculated considering the failure rates of the components, which affect the reliability performance...

  7. Designs for Risk Evaluation and Management

    Energy Technology Data Exchange (ETDEWEB)

    2015-12-01

    The Designs for Risk Evaluation and Management (DREAM) tool was developed as part of the effort to quantify the risk of geologic storage of carbon dioxide (CO2) under the U.S. Department of Energy's National Risk Assessment Partnership (NRAP). DREAM is an optimization tool created to identify optimal monitoring schemes that minimize the time to first detection of CO2 leakage from a subsurface storage formation. DREAM acts as a post-processer on user-provided output from subsurface leakage simulations. While DREAM was developed for CO2 leakage scenarios, it is applicable to any subsurface leakage simulation of the same output format. The DREAM tool is comprised of three main components: (1) a Java wizard used to configure and execute the simulations, (2) a visualization tool to view the domain space and optimization results, and (3) a plotting tool used to analyze the results. A secondary Java application is provided to aid users in converting common American Standard Code for Information Interchange (ASCII) output data to the standard DREAM hierarchical data format (HDF5). DREAM employs a simulated annealing approach that searches the solution space by iteratively mutating potential monitoring schemes built of various configurations of monitoring locations and leak detection parameters. This approach has proven to be orders of magnitude faster than an exhaustive search of the entire solution space. The user's manual illustrates the program graphical user interface (GUI), describes the tool inputs, and includes an example application.

  8. Design of a high-lift experiment in water including active flow control

    International Nuclear Information System (INIS)

    Beutel, T; Schwerter, M; Büttgenbach, S; Leester-Schädel, M; Sattler, S; El Sayed, Y; Radespiel, R; Zander, M; Sinapius, M; Wierach, P

    2014-01-01

    This paper describes the structural design of an active flow-control experiment. The aim of the experiment is to investigate the increase in efficiency of an internally blown Coanda flap using unsteady blowing. The system uses tailor-made microelectromechanical (MEMS) pressure sensors to determine the state of the oncoming flow and an actuated lip to regulate the mass flow and velocity of a stream near a wall over the internally blown flap. Sensors and actuators are integrated into a highly loaded system that is extremely compact. The sensors are connected to a bus system that feeds the data into a real-time control system. The piezoelectric actuators using the d 33 effect at a comparable low voltage of 120 V are integrated into a lip that controls the blowout slot height. The system is designed for closed-loop control that efficiently avoids flow separation on the Coanda flap. The setup is designed for water-tunnel experiments in order to reduce the free-stream velocity and the system’s control frequency by a factor of 10 compared with that in air. This paper outlines the function and verification of the system’s main components and their development. (technical note)

  9. Design Concept Evaluation Using System Throughput Model

    International Nuclear Information System (INIS)

    Sequeira, G.; Nutt, W. M.

    2004-01-01

    The U.S. Department of Energy (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is currently developing the technical bases to support the submittal of a license application for construction of a geologic repository at Yucca Mountain, Nevada to the U.S. Nuclear Regulatory Commission. The Office of Repository Development (ORD) is responsible for developing the design of the proposed repository surface facilities for the handling of spent nuclear fuel and high level nuclear waste. Preliminary design activities are underway to sufficiently develop the repository surface facilities design for inclusion in the license application. The design continues to evolve to meet mission needs and to satisfy both regulatory and program requirements. A system engineering approach is being used in the design process since the proposed repository facilities are dynamically linked by a series of sub-systems and complex operations. In addition, the proposed repository facility is a major system element of the overall waste management process being developed by the OCRWM. Such an approach includes iterative probabilistic dynamic simulation as an integral part of the design evolution process. A dynamic simulation tool helps to determine if: (1) the mission and design requirements are complete, robust, and well integrated; (2) the design solutions under development meet the design requirements and mission goals; (3) opportunities exist where the system can be improved and/or optimized; and (4) proposed changes to the mission, and design requirements have a positive or negative impact on overall system performance and if design changes may be necessary to satisfy these changes. This paper will discuss the type of simulation employed to model the waste handling operations. It will then discuss the process being used to develop the Yucca Mountain surface facilities model. The latest simulation model and the results of the simulation and how the data were used in the design

  10. Performance evaluation and design of flight vehicle control systems

    CERN Document Server

    Falangas, Eric T

    2015-01-01

    This book will help students, control engineers and flight dynamics analysts to model and conduct sophisticated and systemic analyses of early flight vehicle designs controlled with multiple types of effectors and to design and evaluate new vehicle concepts in terms of satisfying mission and performance goals. Performance Evaluation and Design of Flight Vehicle Control Systems begins by creating a dynamic model of a generic flight vehicle that includes a range of elements from airplanes and launch vehicles to re-entry vehicles and spacecraft. The models may include dynamic effects dealing with structural flexibility, as well as dynamic coupling between structures and actuators, propellant sloshing, and aeroelasticity, and they are typically used for control analysis and design. The book shows how to efficiently combine different types of effectors together, such as aero-surfaces, TVC, throttling engines and RCS, to operate as a system by developing a mixing logic atrix. Methods of trimming a vehicle controll...

  11. Evaluation of Interactive Website Design Indicators for e-Entrepreneurship

    Directory of Open Access Journals (Sweden)

    Chih-Chao Chung

    2016-04-01

    Full Text Available Using an analytic network process (ANP as an analytical tool, this study aims to construct an ANP evaluation model of interactive website design indicators. Through a review of the literature, interactive website design of e-entrepreneurship is generalized to the following dimensions: (1 Design; (2 Checking; (3 Service; (4 Interactive; and (5 Promotion, including 19 design indicators. The research is conducted for a case company. According to the findings, the model helps the case company review its current execution of interactive website design indicators and the experts’ opinions of the importance of interactive website design indicators. In addition, by comprehensive comparison, it confirms key design indicators and analyzes the managerial implications to help the case company set up precise strategic planning and resource distribution to enhance corporate operational performance and competitiveness.

  12. Human factors design of nuclear power plant control rooms including computer-based operator aids

    International Nuclear Information System (INIS)

    Bastl, W.; Felkel, L.; Becker, G.; Bohr, E.

    1983-01-01

    The scientific handling of human factors problems in control rooms began around 1970 on the basis of safety considerations. Some recent research work deals with the development of computerized systems like plant balance calculation, safety parameter display, alarm reduction and disturbance analysis. For disturbance analysis purposes it is necessary to homogenize the information presented to the operator according to the actual plant situation in order to supply the operator with the information he most urgently needs at the time. Different approaches for solving this problem are discussed, and an overview is given on what is being done. Other research projects concentrate on the detailed analysis of operators' diagnosis strategies in unexpected situations, in order to obtain a better understanding of their mental processes and the influences upon them when such situations occur. This project involves the use of a simulator and sophisticated recording and analysis methods. Control rooms are currently designed with the aid of mock-ups. They enable operators to contribute their experience to the optimization of the arrangement of displays and controls. Modern control rooms are characterized by increasing use of process computers and CRT (Cathode Ray Tube) displays. A general concept for the integration of the new computerized system and the conventional control panels is needed. The technical changes modify operators' tasks, and future ergonomic work in nuclear plants will need to consider the re-allocation of function between man and machine, the incorporation of task changes in training programmes, and the optimal design of information presentation using CRTs. Aspects of developments in control room design are detailed, typical research results are dealt with, and a brief forecast of the ergonomic contribution to be made in the Federal Republic of Germany is given

  13. Evaluation of technical design of advanced information display

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Woo Chang; Kang, Young Ju; Ji, Jung Hun; Jang, Sung Pil; Jung, Sung Hae [Kumoh National Institute of Technology, Gumi (Korea, Republic of)

    2003-03-15

    The performance of human machine system such as nuclear power plant is highly dependent on the suitability of the interface design of the system. As the computer technology is highly developed, the mental model of computer users including NPP operators has been changed from analogue display type-based stereotype to digitalized one. Therefore, it is necessary and confident to consider the issues to evaluate system suitability of advanced information display on CRT or CBP (Computer Based Procedure). This document is intended for providing an updated and expanded set of user-interface guidelines that meet the needs of designing information display on CRT by finding the generic guidelines involving information display design issues as much as possible. The design Issues and resolutions from the finding may provide the cues for the designers and evaluators of the specific man machine interfaces of digitalized devices.

  14. Evaluation of technical design of advanced information display

    International Nuclear Information System (INIS)

    Cha, Woo Chang; Kang, Young Ju; Ji, Jung Hun; Jang, Sung Pil; Jung, Sung Hae

    2003-03-01

    The performance of human machine system such as nuclear power plant is highly dependent on the suitability of the interface design of the system. As the computer technology is highly developed, the mental model of computer users including NPP operators has been changed from analogue display type-based stereotype to digitalized one. Therefore, it is necessary and confident to consider the issues to evaluate system suitability of advanced information display on CRT or CBP (Computer Based Procedure). This document is intended for providing an updated and expanded set of user-interface guidelines that meet the needs of designing information display on CRT by finding the generic guidelines involving information display design issues as much as possible. The design Issues and resolutions from the finding may provide the cues for the designers and evaluators of the specific man machine interfaces of digitalized devices

  15. [Design and evaluation of DAVIH VIH-2].

    Science.gov (United States)

    Martín Alfonso, Dayamí; Silva Cabrera, Eladio; Pérez Guevara, María T; Díaz Herrera, Dervel F; Romero Martínez, Kenia; Díaz Torres, Héctor M; Lubián Caballero, Ana L; Ruiz Gutiérrez, Nancy; Ortiz Losada, Eva

    2007-01-01

    The results of the design and evaluation of DAVIH VIH-2 diagnosing system, an indirect Elisa for screening of HIV-2 antibodies, which uses a HIV-2 glycoprotein gp36 synthetic peptide in its solid phase, were exposed. In the system evaluation using WHO reference panels, 100% sensitivity, 99,81% specificity, 99,81% efficacy and very good concordance level (kappa = 0.978) were attained. Serum samples of 959 individuals with undetermined or negative results to the HIV-1 antibodies confirmation (DAVIH blot) were evaluated by the DAVIH VIH-2 system. Twenty four samples were reactive, six of which had confirmed HIV-2 antibodies. These results allowed recommending the introduction of this diagnostic kit in the HIV infection diagnosing algorithm in Cuba.

  16. New tools for evaluating LQAS survey designs.

    Science.gov (United States)

    Hund, Lauren

    2014-02-15

    Lot Quality Assurance Sampling (LQAS) surveys have become increasingly popular in global health care applications. Incorporating Bayesian ideas into LQAS survey design, such as using reasonable prior beliefs about the distribution of an indicator, can improve the selection of design parameters and decision rules. In this paper, a joint frequentist and Bayesian framework is proposed for evaluating LQAS classification accuracy and informing survey design parameters. Simple software tools are provided for calculating the positive and negative predictive value of a design with respect to an underlying coverage distribution and the selected design parameters. These tools are illustrated using a data example from two consecutive LQAS surveys measuring Oral Rehydration Solution (ORS) preparation. Using the survey tools, the dependence of classification accuracy on benchmark selection and the width of the 'grey region' are clarified in the context of ORS preparation across seven supervision areas. Following the completion of an LQAS survey, estimation of the distribution of coverage across areas facilitates quantifying classification accuracy and can help guide intervention decisions.

  17. The European source-term evaluation code ASTEC: status and applications, including CANDU plant applications

    International Nuclear Information System (INIS)

    Van Dorsselaere, J.P.; Giordano, P.; Kissane, M.P.; Montanelli, T.; Schwinges, B.; Ganju, S.; Dickson, L.

    2004-01-01

    Research on light-water reactor severe accidents (SA) is still required in a limited number of areas in order to confirm accident-management plans. Thus, 49 European organizations have linked their SA research in a durable way through SARNET (Severe Accident Research and management NETwork), part of the European 6th Framework Programme. One goal of SARNET is to consolidate the integral code ASTEC (Accident Source Term Evaluation Code, developed by IRSN and GRS) as the European reference tool for safety studies; SARNET efforts include extending the application scope to reactor types other than PWR (including VVER) such as BWR and CANDU. ASTEC is used in IRSN's Probabilistic Safety Analysis level 2 of 900 MWe French PWRs. An earlier version of ASTEC's SOPHAEROS module, including improvements by AECL, is being validated as the Canadian Industry Standard Toolset code for FP-transport analysis in the CANDU Heat Transport System. Work with ASTEC has also been performed by Bhabha Atomic Research Centre, Mumbai, on IPHWR containment thermal hydraulics. (author)

  18. Design for Motivation: Evaluation of a Design Tool

    OpenAIRE

    Chasanidou, Dimitra

    2018-01-01

    Design for motivation constitutes a design practice that focuses on the activation of human motives to perform an action. There is an increasing need to design motivational and engaging mechanisms for voluntary systems, such as innovation platforms, where user participation is a key target. When designing for motivation, a challenge of the early design phases is the selection of appropriate design tool and strategy. The current work presents a design tool, namely DEMO (DEsign for MOtivation),...

  19. Evaluations of 1990 PRISM design revisions

    International Nuclear Information System (INIS)

    Van Tuyle, G.J.; Slovik, G.C.; Chan, B.C.; Aronson, A.L.; Kennett, R.J.

    1992-03-01

    Analyses of the 1990 version of the PRISM Advanced Liquid Metal Reactor (ALMR) design are presented and discussed. Most of the calculations were performed using BNL computer codes, particularly SSC and MINET. In many cases, independent BNL calculations were compared against analyses presented by General Electric when they submitted the PRISM design revisions for evaluation by the Nuclear Regulatory Commission (NRC). The current PRISM design utilizes the metallic fuel developed by Argonne National Laboratory (ANL) which facilitates the passive/''inherent'' shutdown mechanism that acts to shut down reactor power production whenever the system overheats. There are a few vulnerabilities in the passive shutdown, with the most worrisome being the positive feedback from sodium density decreases or sodium voiding. Various postulated unscrammed events were examined by GE and/or BNL, and much of the analysis discussed in this report is focused on this category of events. For the most part, the BNL evaluations confirm the information submitted by General Electric. The principal areas of concern are related to the performance of the ternary metal fuel, and may be resolved as ANL continues with its fuel development and testing program

  20. A SUMMARY COMPARISON OF DESIGN EVALUATION TECHNIQUES

    Energy Technology Data Exchange (ETDEWEB)

    Spielman, Zachary; Hill, Rachael

    2017-06-01

    The United States’ fleet of Nuclear Reactors is considering modernizing their control rooms and instrumentation as an effort to avoid component obsolescence, keep up with competing industries, and cater to a new work force among others. Multiple technologies have potential to improve the control room. In attempts to evaluate the available options researchers employ a variety of measures to ensure the best candidate is used in a modernizing effort. The NRC is in charge of ensuring any new design has been thoroughly vetted before approving a license. Laid out in NUREG-0711 “Human Factors Engineering Program Review Model” is the review criteria for design validation. As there are a variety of measures currently used to evaluate candidate technologies, this paper seeks to identify weaknesses in the common measures used to design and validate technology in control room modernization efforts. Identifying where measurements are not meeting the criteria will help the control room modernization research platform identify where measurement development needs to occur. This will help ensure that current performance measurements are producing as reliable results as possible to select the right technology to integrate into nuclear operating control rooms.

  1. [Evaluation of Cellular Effects Caused by Lunar Regolith Simulant Including Fine Particles].

    Science.gov (United States)

    Horie, Masanori; Miki, Takeo; Honma, Yoshiyuki; Aoki, Shigeru; Morimoto, Yasuo

    2015-06-01

    The National Aeronautics and Space Administration has announced a plan to establish a manned colony on the surface of the moon, and our country, Japan, has declared its participation. The surface of the moon is covered with soil called lunar regolith, which includes fine particles. It is possible that humans will inhale lunar regolith if it is brought into the spaceship. Therefore, an evaluation of the pulmonary effects caused by lunar regolith is important for exploration of the moon. In the present study, we examine the cellular effects of lunar regolith simulant, whose components are similar to those of lunar regolith. We focused on the chemical component and particle size in particular. The regolith simulant was fractionated to lunar regolith simulant such as cell membrane damage, induction of oxidative stress and proinflammatory effect.

  2. Some consequences of including low frequencies in the evaluation of floor impact sound

    DEFF Research Database (Denmark)

    Rindel, Jens Holger; Rasmussen, Birgit

    1996-01-01

    A method for including frequencies down to 50 Hz in the evaluation of floor impact sound has become available with the new version of ISO 717-2. In addition to the single number quantity for rating the impact sound insulation, a new spectrum adaptation term has been defined. The method has been...... studied by the Acoustics Group of the Nordic Committee on Building Regulations. The new method has been applied to a large number of recent measuring results from the Nordic countries. It was found that the spectrum adaptation term for the extended frequency range depends on the type of floor construction...... frequency range in future building regulations or in a system for sound classification of dwellings have been considered. However, there are several problems to be solved, among which are a lack of available data for floor constructions at low frequencies, an increased measurement uncertainty, and the fact...

  3. Evaluation of the Supraglottic and Subglottic Activities Including Acoustic Assessment of the Opera-Chant Singers.

    Science.gov (United States)

    Petekkaya, Emine; Yücel, Ahmet Hilmi; Sürmelioğlu, Özgür

    2017-12-28

    Opera and chant singers learn to effectively use aerodynamic components by breathing exercises during their education. Aerodynamic components, including subglottic air pressure and airflow, deteriorate in voice disorders. This study aimed to evaluate the changes in aerodynamic parameters and supraglottic structures of men and women with different vocal registers who are in an opera and chant education program. Vocal acoustic characteristics, aerodynamic components, and supraglottic structures were evaluated in 40 opera and chant art branch students. The majority of female students were sopranos, and the male students were baritone or tenor vocalists. The acoustic analyses revealed that the mean fundamental frequency was 152.33 Hz in the males and 218.77 Hz in the females. The estimated mean subglottal pressures were similar in females (14.99 cmH 2 O) and in males (14.48 cmH 2 O). Estimated mean airflow rates were also similar in both groups. The supraglottic structure compression analyses revealed partial anterior-posterior compressions in 2 tenors and 2 sopranos, and false vocal fold compression in 2 sopranos. Opera music is sung in high-pitched sounds. Attempts to sing high-pitched notes and frequently using register transitions overstrain the vocal structures. This intense muscular effort eventually traumatizes the vocal structures and causes supraglottic activity. Copyright © 2017 The Voice Foundation. Published by Elsevier Inc. All rights reserved.

  4. Thermal enhanced vapor extraction systems: Design, application and performance prediction including contaminant behavior

    International Nuclear Information System (INIS)

    Phelan, J.M.; Webb, S.W.

    1994-01-01

    Soil heating technologies have been proposed as a method to accelerate contaminant removal from subsurface soils. These methods include the use of hot air, steam, conductive heaters, in-situ resistive heating and in-situ radiofrequency heating (Buettner et.al., EPA, Dev et.al., Heath et.al.). Criteria for selection of a particular soil heating technology is a complex function of contaminant and soil properties, and efficiency in energy delivery and contaminant removal technologies. The work presented here seeks to expand the understanding of the interactions of subsurface water, contaminant, heat and vacuum extraction through model predictions and field data collection. Field demonstration will involve the combination of two soil heating technologies (resistive and dielectric) with a vacuum vapor extraction system and will occur during the summer of 1994

  5. Evaluating Stellarator Divertor Designs with EMC3

    Science.gov (United States)

    Bader, Aaron; Anderson, D. T.; Feng, Y.; Hegna, C. C.; Talmadge, J. N.

    2013-10-01

    In this paper various improvements of stellarator divertor design are explored. Next step stellarator devices require innovative divertor solutions to handle heat flux loads and impurity control. One avenue is to enhance magnetic flux expansion near strike points, somewhat akin to the X-Divertor concept in Tokamaks. The effect of judiciously placed external coils on flux deposition is calculated for configurations based on the HSX stellarator. In addition, we attempt to optimize divertor plate location to facilitate the external coil placement. Alternate areas of focus involve altering edge island size to elucidate the driving physics in the edge. The 3-D nature of stellarators complicates design and necessitates analysis of new divertor structures with appropriate simulation tools. We evaluate the various configurations with the coupled codes EMC3-EIRENE, allowing us to benchmark configurations based on target heat flux, impurity behavior, radiated power, and transitions to high recycling and detached regimes. Work supported by DOE-SC0006103.

  6. Light water reactors fuel assembly mechanical design and evaluation

    International Nuclear Information System (INIS)

    Anon.

    1981-01-01

    This standard establishes a procedure for performing an evaluation of the mechanical design of fuel assemblies for light water-cooled commercial power reactors. It does not address the various aspects of neutronic or thermalhydraulic performance except where these factors impose loads or constraints on the mechanical design of the fuel assemblies. This standard also includes a set of specific requirements for design, various potential performance problems and criteria aimed specifically at averting them. This standard replaces ANSI/ANS-57.5-1978

  7. DNA sequence analyses of blended herbal products including synthetic cannabinoids as designer drugs.

    Science.gov (United States)

    Ogata, Jun; Uchiyama, Nahoko; Kikura-Hanajiri, Ruri; Goda, Yukihiro

    2013-04-10

    In recent years, various herbal products adulterated with synthetic cannabinoids have been distributed worldwide via the Internet. These herbal products are mostly sold as incense, and advertised as not for human consumption. Although their labels indicate that they contain mixtures of several potentially psychoactive plants, and numerous studies have reported that they contain a variety of synthetic cannabinoids, their exact botanical contents are not always clear. In this study, we investigated the origins of botanical materials in 62 Spice-like herbal products distributed on the illegal drug market in Japan, by DNA sequence analyses and BLAST searches. The nucleotide sequences of four regions were analyzed to identify the origins of each plant species in the herbal mixtures. The sequences of "Damiana" (Turnera diffusa) and Lamiaceae herbs (Mellissa, Mentha and Thymus) were frequently detected in a number of products. However, the sequences of other plant species indicated on the packaging labels were not detected. In a few products, DNA fragments of potent psychotropic plants were found, including marijuana (Cannabis sativa), "Diviner's Sage" (Salvia divinorum) and "Kratom" (Mitragyna speciosa). Their active constituents were also confirmed using gas chromatography-mass spectrometry (GC-MS) and liquid chromatography-mass spectrometry (LC-MS), although these plant names were never indicated on the labels. Most plant species identified in the products were different from the plants indicated on the labels. The plant materials would be used mainly as diluents for the psychoactive synthetic compounds, because no reliable psychoactive effects have been reported for most of the identified plants, with the exception of the psychotropic plants named above. Copyright © 2012 Elsevier Ireland Ltd. All rights reserved.

  8. Evaluation of technical design of advanced information display(II)

    International Nuclear Information System (INIS)

    Cha, Woo Chang; Kang, Young Ju; Ji, Jung Hun; Jang, Sung Pil; Jung, Sung Hae; Park, Hyun Jin

    2004-02-01

    As the computer technology is highly developed, the mental model of computer users including NPP operators has been changed from analogue display type-based stereotype to digitalized one. Therefore, it is necessary and confident to consider the issues to evaluate system suitability of advanced information display on visual display terminal such as CRT. This document is intended for providing an updated and expanded set of user-interface guidelines that meet the needs of designing information display on CRT by finding the generic guidelines involving information display design issues, and the relationship among the guidelines. The design issues and resolutions from the finding may provide the cues for the designers and evaluators of the specific man machine interfaces of digitalized devices

  9. Evaluation of technical design of advanced information display(II)

    Energy Technology Data Exchange (ETDEWEB)

    Cha, Woo Chang; Kang, Young Ju; Ji, Jung Hun; Jang, Sung Pil; Jung, Sung Hae; Park, Hyun Jin [Kumoh National Univ., Gumi (Korea, Republic of)

    2004-02-15

    As the computer technology is highly developed, the mental model of computer users including NPP operators has been changed from analogue display type-based stereotype to digitalized one. Therefore, it is necessary and confident to consider the issues to evaluate system suitability of advanced information display on visual display terminal such as CRT. This document is intended for providing an updated and expanded set of user-interface guidelines that meet the needs of designing information display on CRT by finding the generic guidelines involving information display design issues, and the relationship among the guidelines. The design issues and resolutions from the finding may provide the cues for the designers and evaluators of the specific man machine interfaces of digitalized devices.

  10. Uncertainty-driven nuclear data evaluation including thermal (n,α) applied to 59Ni

    Science.gov (United States)

    Helgesson, P.; Sjöstrand, H.; Rochman, D.

    2017-11-01

    This paper presents a novel approach to the evaluation of nuclear data (ND), combining experimental data for thermal cross sections with resonance parameters and nuclear reaction modeling. The method involves sampling of various uncertain parameters, in particular uncertain components in experimental setups, and provides extensive covariance information, including consistent cross-channel correlations over the whole energy spectrum. The method is developed for, and applied to, 59Ni, but may be used as a whole, or in part, for other nuclides. 59Ni is particularly interesting since a substantial amount of 59Ni is produced in thermal nuclear reactors by neutron capture in 58Ni and since it has a non-threshold (n,α) cross section. Therefore, 59Ni gives a very important contribution to the helium production in stainless steel in a thermal reactor. However, current evaluated ND libraries contain old information for 59Ni, without any uncertainty information. The work includes a study of thermal cross section experiments and a novel combination of this experimental information, giving the full multivariate distribution of the thermal cross sections. In particular, the thermal (n,α) cross section is found to be 12.7 ± . 7 b. This is consistent with, but yet different from, current established values. Further, the distribution of thermal cross sections is combined with reported resonance parameters, and with TENDL-2015 data, to provide full random ENDF files; all of this is done in a novel way, keeping uncertainties and correlations in mind. The random files are also condensed into one single ENDF file with covariance information, which is now part of a beta version of JEFF 3.3. Finally, the random ENDF files have been processed and used in an MCNP model to study the helium production in stainless steel. The increase in the (n,α) rate due to 59Ni compared to fresh stainless steel is found to be a factor of 5.2 at a certain time in the reactor vessel, with a relative

  11. A rational evaluation of structural design loads

    International Nuclear Information System (INIS)

    Tasaka, S.

    1993-01-01

    The reliability-based seismic design of structures is a design method ensuring that the structural seismic capacity is not less than the maximum seismic load or load effect for a prescribed value of the reliability index, wherein the design reference period, n, is used to specify the n-year maximum load. In the conventional Load and Resistance Factor Design (LRFD) method the design load is commonly determined on the basis of the n-year maximum the probability distribution of which may be given in some different ways. However, in contrast with the structural capacity the n-year maximum load usually involves much larger variabilities. The effort to decrease the variability would, hence, be effective for the purpose of avoiding nuclear power plant (NPP) structures having unnecessarily large capacities. A possible way to do this is to consider the joint probability distribution of the n-year 1st and 2nd maxima of the seismic load derived from the formula of extreme order statistics. Since the reliability index is conventionally associated with the n-year 1st maximum, the conditional probability distribution rather than the joint one of the n-year 1st maximum given a value of the n-year 2nd one will be considered. Three conditional extreme value distributions, which correspond to the usual extreme value distributions of Types I, II and III, and their statistical moments up to the second order are presented. Within the framework of the first-order second moment method, the conditional statistical moments are utilized to calculate the reliability index as well as the design value of the seismic load. The seismic load considered herein is represented by the peak ground acceleration (PGA) in n years. The present scheme is applied to evaluate the design PGA's at II sites in Japan where samples of the annual 1st and 2nd PGA's have been obtained by using historical seismic data. In this application the following two points are of our interest: (a) Define the reliability

  12. Fatigue evaluation including environmental effects for primary circuit components in nuclear power plants

    International Nuclear Information System (INIS)

    Seichter, Johannes; Reese, Sven H.; Klucke, Dietmar

    2013-01-01

    The influence of LWR coolant environment to the lifetime of materials in Nuclear Power Plants is in discussion internationally. Environmental phenomena were investigated in laboratory tests and published in recent years. The discussion is mainly focused both on the transition from laboratory to real plant components and on numerical calculation procedures. Since publishing of the NUREG/CR-6909 report in 2007, formulae for calculating the Fen factors have been modified several times. Various calculation procedures like the so called 'Strain-integrated Method' and 'Simplified Approach' have been published while each approach yields to different results. The recent revision of the calculation procedure, proposed by ANL in 2012, is presented and discussed with regard to possible variations in the results depending on the assumptions made. In German KTA Rules the effect of environmentally assisted fatigue (EAF) is taken into account by means of so called attention thresholds. If the threshold value is exceeded, further measures like NDT, in-service inspections including fracture mechanical evaluations or detailed assessment procedures have to be performed. One way to handle those measures is to apply sophisticated procedures and to show that the calculated CUF is below the defined attention thresholds. On the basis of a practical example, methods and approaches will be discussed and recommendations in terms of avoiding over-conservatism and misinterpretation will be presented.

  13. Fatigue evaluation including environmental effects for primary circuit components in nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Seichter, Johannes [Siempelkamp Pruef- und Gutachter-Gesellschaft mbH, Dresden (Germany); Reese, Sven H.; Klucke, Dietmar [Component Technology Global Unit Generation, E.ON Kernkraft GmbH, Hannover (Germany)

    2013-05-15

    The influence of LWR coolant environment to the lifetime of materials in Nuclear Power Plants is in discussion internationally. Environmental phenomena were investigated in laboratory tests and published in recent years. The discussion is mainly focused both on the transition from laboratory to real plant components and on numerical calculation procedures. Since publishing of the NUREG/CR-6909 report in 2007, formulae for calculating the Fen factors have been modified several times. Various calculation procedures like the so called 'Strain-integrated Method' and 'Simplified Approach' have been published while each approach yields to different results. The recent revision of the calculation procedure, proposed by ANL in 2012, is presented and discussed with regard to possible variations in the results depending on the assumptions made. In German KTA Rules the effect of environmentally assisted fatigue (EAF) is taken into account by means of so called attention thresholds. If the threshold value is exceeded, further measures like NDT, in-service inspections including fracture mechanical evaluations or detailed assessment procedures have to be performed. One way to handle those measures is to apply sophisticated procedures and to show that the calculated CUF is below the defined attention thresholds. On the basis of a practical example, methods and approaches will be discussed and recommendations in terms of avoiding over-conservatism and misinterpretation will be presented.

  14. Designing the model for evaluating business quality in Croatia

    Directory of Open Access Journals (Sweden)

    Ana Ježovita

    2015-01-01

    Full Text Available The main objective of the paper includes designing a model for evaluating the financial quality of business operations. In that context, for the paper purposes, the financial quality of business operations is defined as an ability to achieve adequate value of individual financial ratios for financial position and performance evaluation. The objective of the model is to obtain comprehensive conclusion about the financial quality of business operation using only value of the function. Data used for designing the model is limited to financial data available from the annual balance sheet and income statement. Those limitations offer the opportunity for all sizes of companies from the non-financial business economy sector to use the designed model for evaluation purposes. Statistical methods used for designing the model are multivariate discriminant analysis and logistic regression. Discriminant analysis resulted in the function which includes five individual financial ratios with the best discriminant power. Respecting the results obtained in the classification matrix with classification accuracy of 95.92% by the original sample, or accuracy of 96.06% for the independent sample, it can be concluded that it is possible to evaluate the financial quality of business operations of companies in Croatia by using the model composed of individual financial ratios. Conducted logistic regression confirms the results obtained using discriminant analysis.

  15. Aero-structural optimization of wind turbine blades using a reduced set of design load cases including turbulence

    DEFF Research Database (Denmark)

    Sessarego, Matias; Shen, Wen Zhong

    2018-01-01

    Modern wind turbine aero-structural blade design codes generally use a smaller fraction of the full design load base (DLB) or neglect turbulent inflow as defined by the International Electrotechnical Commission standards. The current article describes an automated blade design optimization method...... based on surrogate modeling that includes a very large number of design load cases (DLCs) including turbulence. In the present work, 325 DLCs representative of the full DLB are selected based on the message-passing-interface (MPI) limitations in Matlab. Other methods are currently being investigated, e.......g. a Python MPI implementation, to overcome the limitations in Matlab MPI and ultimately achieve a full DLB optimization framework. The reduced DLB and the annual energy production are computed using the state-of-the-art aero-servo-elastic tool HAWC2. Furthermore, some of the interior dimensions of the blade...

  16. Job analysis for training design and evaluation

    International Nuclear Information System (INIS)

    Andersson, H.; Baeck, P.; Wirstad, J.

    1979-01-01

    The report describes a job analysis method which has been used for competency requirements and training evaluation purposes on three jobs in a Swedish nuclear power station. The jobs are the shift supervisor, the reactor operator and the turbine operator. The method is based on a system analytical approach. Through a topdown analysis of the power generation system a structure is derived which is used for an inventory of possible operator tasks. The primary source for actual task generation was interviews with operators and with other personnel who are cooperating with the operators. The method suggests alternative sources for the task generation when operator interviews are not feasible, e.g. in systems which are being developed or when operator experiences are lacking. The result of the job analysis is a set of typical tasks for each job. These tasks represent the contents of the job to be considered in the planning of job training and for recruitment requirements. The same job analysis method was used for training design and evaluation in a Finnish nuclear power station. The concluding remarks of this report are made in the light of this study also. This report is based on a research project B15/77 from the Swedish Nuclear Power Inspectorate. (author)

  17. Evaluation of plant-wide WWTP control strategies including the effects of filamentous bulking sludge

    DEFF Research Database (Denmark)

    Flores Alsina, Xavier; Comas, J.S.; Rodríguez Roda, I.

    2009-01-01

    The main objective of this paper is to evaluate the effect of filamentous bulking sludge on the predicted performance of simulated plant-wide WWTP control strategies. First, as a reference case, several control strategies are implemented, simulated and evaluated using the IWA Benchmark Simulation...

  18. Responses to Including Parents in Teacher Evaluation Policy: A Critical Policy Analysis

    Science.gov (United States)

    Fernández, Erica; LeChasseur, Kimberly; Donaldson, Morgaen L.

    2018-01-01

    The intersection of development in family and school settings has been well established and education policies have begun to promote ways to bridge the two contexts (i.e. teacher evaluations). For this manuscript, authors focus on how teachers and principals used a state educator evaluation policy to position parents as authorities on education.…

  19. Richards Barrier LA Reference Design Feature Evaluation

    International Nuclear Information System (INIS)

    N.E. Kramer

    1999-01-01

    The Richards Barrier is one of the design features of the repository to be considered for the License Application (LA), Richards was a soil scientist who first described the diversion of moisture between two materials with different hydrologic properties. In this report, a Richards Barrier is a special type of backfill with a fine-grained material (such as sand) overlaying a coarse-grained material (such as gravel). Water that enters an emplacement drift will first encounter the fine-grained material and be transported around the coarse-grained material covering the waste package, thus protecting the waste package from contact with most of the groundwater. The objective of this report is to discuss the benefits and liabilities to the repository by the inclusion of a Richards Barrier type backfill in emplacement drifts. The Richards Barrier can act as a barrier to water flow, can reduce the waste package material dissolution rate, limit mobilization of the radionuclides, and can provide structural protection for the waste package. The scope of this report is to: (1) Analyze the behavior of barrier materials following the intrusion of groundwater for influxes of 1 to 300 mm per year. The report will demonstrate diversion of groundwater intrusions into the barrier over an extended time period when seismic activity and consolidation may cause the potential for liquefaction and settlement of the Richards Barrier. (2) Review the thermal effects of the Richards Barrier on material behavior. (3) Analyze the effect of rockfall on the performance of the Richards Barrier and the depth of the barrier required to protect waste packages under the barrier. (4) Review radiological and heating conditions on placement of multiple layers of the barrier. Subsurface Nuclear Safety personnel will perform calculations to determine the radiation reduction-time relationship and shielding capacity of the barrier. (5) Evaluate the effects of ventilation on cooling of emplacement drifts and

  20. ADEME energy transition scenarios. Summary including a macro-economic evaluation 2030 2050

    International Nuclear Information System (INIS)

    2014-05-01

    fourfold reduction in greenhouse gas emissions is achievable. By supporting the green economy, which embraces business activities of the future such as renewable energy production, energy recovery from waste, recycling and eco-design - 'resources' that are all available within France - we can move towards robust and sustainable growth. The present economic crisis should not halt our efforts. Greater energy efficiency means higher employment. Breaking our dependency on fossil fuels is the way to anticipate future economic conditions - fossil energy prices will inevitably rise during the coming decades - and to reduce our vulnerability to imports that have become a significant burden (Euro 69 billion in 2012) and comply with our international commitments to reduce our greenhouse gas emissions. Acting now clearly has a cost, especially during the first years, but the macro-economic evaluation that accompanies the 2030-2050 Energy Transition scenarios show that in addition to environmental benefits, the energy transition could also have a beneficial impact on the French economy

  1. A Monte Carlo tool for evaluating VMAT and DIMRT treatment deliveries including planar detectors

    International Nuclear Information System (INIS)

    Asuni, G; Van Beek, T A; Venkataraman, S; McCurdy, B M C; Popescu, I A

    2013-01-01

    The aim of this work is to describe and validate a new general research tool that performs Monte Carlo (MC) simulations for volumetric modulated arc therapy (VMAT) and dynamic intensity modulated radiation therapy (DIMRT), simultaneously tracking dose deposition in both the patient CT geometry and an arbitrary planar detector system. The tool is generalized to handle either entrance or exit detectors and provides the simulated dose for the individual control-points of the time-dependent VMAT and DIMRT deliveries. The MC simulation tool was developed with the EGSnrc radiation transport. For the individual control point simulation, we rotate the patient/phantom volume only (i.e. independent of the gantry and planar detector geometries) using the gantry angle in the treatment planning system (TPS) DICOM RP file such that each control point has its own unique phantom file. After MC simulation, we obtained the total dose to the phantom by summing dose contributions for all control points. Scored dose to the sensitive layer of the planar detector is available for each control point. To validate the tool, three clinical treatment plans were used including VMAT plans for a prostate case and a head-and-neck case, and a DIMRT plan for a head-and-neck case. An electronic portal imaging device operated in ‘movie’ mode was used with the VMAT plans delivered to cylindrical and anthropomorphic phantoms to validate the code using an exit detector. The DIMRT plan was delivered to a novel transmission detector, to validate the code using an entrance detector. The total MC 3D absolute doses in patient/phantom were compared with the TPS doses, while 2D MC doses were compared with planar detector doses for all individual control points, using the gamma evaluation test with 3%/3 mm criteria. The MC 3D absolute doses demonstrated excellent agreement with the TPS doses for all the tested plans, with about 95% of voxels having γ 90% of percentage pixels with γ <1. We found that over

  2. CRBRP sodium circulating pump design evaluation

    International Nuclear Information System (INIS)

    Marrujo, F.; Cook, M.; Manners, L.; Cothran, H.

    1977-12-01

    The following topics are discussed: (1) primary sodium pump design concept; (2) pump level control system; (3) resolution of design problems in stress analysis, dynamics analysis, and mechanical design; (4) model testing; (5) planned performance tests; and (6) fabrication status

  3. [The evaluation of academic emergency department design].

    Science.gov (United States)

    Deniz, Turgut; Aydinuraz, Kuzey; Oktay, Cem; Saygun, Meral; Ağalar, Fatih

    2007-01-01

    In our study which was based upon a questionnaire, the inner and outer architectural designs of emergency services of Emergency Medicine Departments were investigated. In this descriptive study, a standard questionnaire was sent to 26 Emergency Medicine Departments which were operating at that time. In the questionnaire, the internal, external architectural and functional features were questioned. Answers of 22 Emergency Medicine Departments were analysed. Two Emergency Medicine Departments that were not operating at that time were not included in the study. The analysis of the replies revealed that only 59% (n=13) of the Emergency Medicine Departments were designed as an emergency service prior to the construction. The ambulance parking areas were not suitable in 77% of the emergency units while only 54.5% (n=12) had protection against adverse weather conditions. In only 59% (n=13) of the emergency units, a triage unit was present and in only one of the in only one (4.5%), a decontamination room was available. It was understood that only 32% (n=8) of the emergency units were appropriate in enlarging their capacity taking the local risk factors into consideration. There was a toilette for disabled patients in only 18% (n=4) of the units as well. Considering a 12-year of history of the Emergency Medicine in Turkey, the presence of a lecture room is still 68% (n=15) in emergency departments which reflects that academic efforts in this field is emerging in challenging physical conditions. The results of our study revealed that emergency service architecture was neglected in Turkey and medical care given was precluded by the insufficient architecture. The design of emergency services has to be accomplished under guidance of scientific data and rules taking advices of architects who have knowledge and experience on this field.

  4. Design and evaluation of the XBT diode

    International Nuclear Information System (INIS)

    Wright, E.L.; Vlieks, A.; Fant, K.; Pearson, C.; Koontz, R.; Jensen, D.; Miram, G.

    1993-01-01

    This paper describes the design and experimental results achieved with the 440 kV, microperveance 1.9, XBT (X-band Beam Tester) diode. The Pierce gun was developed for the 100 MW X-band klystron; the high power RF source to be used on the NLC (Next Linear Collider). The gun is electrostatically focused (no magnetic compression) to a beam diameter of 6.35 mm, with an area convergence of 110:1. Maximum cathode loading is approximately 25 A/cm 2 , with a beam power density of 770 MW/cm 2 . The measured beam current was within 2% of the value predicted by simulation with EGUN. Transmission through the highly instrumented beam tester was 99.98%. Some novel techniques were used to achieve near perfect beam transmission, which include the use of a reentrant-floating input pole piece

  5. Waste disposal technologies: designs and evaluations

    International Nuclear Information System (INIS)

    Shaw, R.A.

    1987-01-01

    Many states and compacts are presently in the throes of considering what technology to select for their low level waste disposal site. Both the technical and economic aspects of disposal technology are important considerations in these decisions. It is also important that they be considered in the context of the entire system. In the case of a nuclear power plant, that system encompasses the various individual waste streams that contain radioactivity, the processing equipment which reduces the volume and/or alters the form in which the radioisotopes are contained, the packaging of the processed wastes in shipment, and finally its disposal. One further part of this is the monitoring that takes place in all stages of this operation. This paper discusses the results of some research that has been sponsored by EPRI with the principal contractor being Rogers and Associates Engineering Corporation. Included is a description of the distinguishing features found in disposal technologies developed in a generic framework, designs for a selected set of these disposal technologies and the costs which have been derived from these designs. In addition, a description of the early efforts towards defining the performance of these various disposal technologies is described. 5 figures, 1 table

  6. DOE natural phenomenal hazards design and evaluation criteria

    International Nuclear Information System (INIS)

    Murray, R.C.; Nelson, T.A.; Short, S.A.; Kennedy, R.P.; Chander, H.; Hill, J.R.; Kimball, J.K.

    1994-10-01

    It is the policy of the Department of Energy (DOE) to design, construct, and operate DOE facilities so that workers, the general public, and the environment are protected from the impacts of natural phenomena hazards (NPH). Furthermore, DOE has established explicit goals of acceptable risk for NPH performance. As a result, natural phenomena hazard (earthquake, extreme wind, and flood) design and evaluation criteria for DOE facilities have been developed based on target probabilistic performance goals. These criteria include selection of design/evaluation NPH input from probabilistic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. For earthquake considerations, conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior, and by a seismic scale factor. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of qualitative expressions of acceptable behavior and of target quantitative probabilities that acceptable limits of behavior are maintained. The criteria are simple procedures but have a rigorous basis. This paper addresses DOE seismic design and evaluation criteria

  7. Novel modular natural circulation BWR design and safety evaluation

    International Nuclear Information System (INIS)

    Ishii, Mamoru; Shi, Shanbin; Yang, Won Sik; Wu, Zeyun; Rassame, Somboon; Liu, Yang

    2015-01-01

    Highlights: • Introduction of BWR-type natural circulation small modular reactor preliminary design (NMR-50). • Design of long fuel cycle length for the NMR-50. • Design of double passive safety systems for the NMR-50. • RELAP5 analyses of design basis accidents for the NMR-50. - Abstract: The Purdue NMR (Novel Modular Reactor) represents a BWR-type small modular reactor with a significantly reduced reactor pressure vessel (RPV) height. Specifically, it has one third the height of a conventional BWR RPV with an electrical output of 50 MWe. The preliminary design of the NMR-50 including reactor, fuel cycle, and safety systems is described and discussed. The improved neutronics design of the NMR-50 extends the fuel cycle length up to 10 years. The NMR-50 is designed with double passive engineering safety system, which is intended to withstand a prolonged station black out with loss of ultimate heat sink accident such as experienced at Fukushima. In order to evaluate the safety features of the NMR-50, two representative design basis accidents, i.e. main steam line break (MSLB) and bottom drain line break (BDLB), are simulated by using the best-estimate thermal–hydraulic code RELAP5. The RPV water inventory, containment pressure, and the performance of engineering safety systems are investigated for about 33 h after the initiation of the accidents

  8. Screening for Specific Language Impairment in Preschool Children: Evaluating a Screening Procedure Including the Token Test

    Science.gov (United States)

    Willinger, Ulrike; Schmoeger, Michaela; Deckert, Matthias; Eisenwort, Brigitte; Loader, Benjamin; Hofmair, Annemarie; Auff, Eduard

    2017-01-01

    Specific language impairment (SLI) comprises impairments in receptive and/or expressive language. Aim of this study was to evaluate a screening for SLI. 61 children with SLI (SLI-children, age-range 4-6 years) and 61 matched typically developing controls were tested for receptive language ability (Token Test-TT) and for intelligence (Wechsler…

  9. 20 CFR 416.929 - How we evaluate symptoms, including pain.

    Science.gov (United States)

    2010-04-01

    ..., we consider your symptoms, such as pain, to evaluate whether you have a severe physical or mental... medically determinable severe physical or mental impairment(s), but your impairment(s) does not meet or... functionally limiting effects of your symptoms. We will develop evidence regarding the possibility of a...

  10. Design of a Class of Antennas Utilizing MEMS, EBG and Septum Polarizers including Near-field Coupling Analysis

    Science.gov (United States)

    Kim, Ilkyu

    Recent developments in mobile communications have led to an increased appearance of short-range communications and high data-rate signal transmission. New technologies provides the need for an accurate near-field coupling analysis and novel antenna designs. An ability to effectively estimate the coupling within the near-field region is required to realize short-range communications. Currently, two common techniques that are applicable to the near-field coupling problem are 1) integral form of coupling formula and 2) generalized Friis formula. These formulas are investigated with an emphasis on straightforward calculation and accuracy for various distances between the two antennas. The coupling formulas are computed for a variety of antennas, and several antenna configurations are evaluated through full-wave simulation and indoor measurement in order to validate these techniques. In addition, this research aims to design multi-functional and high performance antennas based on MEMS (Microelectromechanical Systems) switches, EBG (Electromagnetic Bandgap) structures, and septum polarizers. A MEMS switch is incorporated into a slot loaded patch antenna to attain frequency reconfigurability. The resonant frequency of the patch antenna can be shifted using the MEM switch, which is actuated by the integrated bias networks. Furthermore, a high gain base-station antenna utilizing beam-tilting is designed to maximize gain for tilted beam applications. To realize this base-station antenna, an array of four dipole-EBG elements is constructed to implement a fixed down-tilt main beam with application in base station arrays. An improvement of the operating range with the EBG-dipole array is evaluated using a simple linkbudget analysis. The septum polarizer has been widely used in circularly polarized antenna systems due to its simple and compact design and high quality of circularity. In this research, the sigmoid function is used to smoothen the edge in the septum design, which

  11. Evaluation of design feature No.20 -- Ground support options

    International Nuclear Information System (INIS)

    Duan, F.

    2000-01-01

    Ground support options are primarily evaluated for emplacement drifts while ground support systems for non-emplacement openings such as access mains and ventilation drifts are not evaluated against LADS evaluation criteria in this report. Considerations include functional requirements for ground support, the use of a steel-lined system, and the feasibility of using an unlined ground support system principally with grouted rock bolts for permanent ground support. The feature evaluation also emphasizes the postclosure effects of ground support materials on waste isolation and the preclosure aspects such as durability, maintainability, constructibility, safety, engineering acceptability, and cost. This evaluation is to: (A) Review the existing analyses, reports, and studies regarding this design feature, and compile relevant information on performance characteristics. (B) Develop an appropriate evaluation approach for evaluating ground support options against evaluation criteria provided by the LADS team. (C) Evaluate ground support options not only for their preclosure performance in terms of drift stability, material durability, maintenance, constructibility, and cost, but also for their postclosure performance in terms of chemical effects of ground support materials (i.e., concrete, steel) on waste isolation and radionuclide transport. Specifically, the scope for ground support options evaluation include: (1) all steel-lined drifts (no cementitious materials), (2) unlined drifts with minimum cementitious materials (e.g., grout for rockbolts), and (3) concrete-lined drifts, with the focus on the postclosure acceptability evaluation. In addition, unlined drifts with zero cementitious materials (e.g., use of frictional bolts such as split sets, Swellex bolts) are briefly discussed. (D) Identify candidate ground support systems that have the potential to enhance the repository performance based on the feature evaluation. and (E) Provide conclusions and recommendations

  12. Preliminary evaluation of FY98 KALIMER shielding design

    Energy Technology Data Exchange (ETDEWEB)

    Yoo, Jae Woon; Kang, Chang Mu; Kim, Young Jin [Korea Atomic Energy Research Institute, Taejon (Korea)

    1999-01-01

    This report describes a preliminary evaluation of the shielding design of FY98 KALIMER. The KALIMER shielding design includes the Inner Fixed Shield of a stainless cylinder located inside the support barrel; the Radial PSDRS Shields which are three B{sub 4}C cylinders located outside the support barrel at core level; the Lower IHX shield of a cylindrical B{sub 4}C plate located above the flow guide; and Inner and Outer IHX shields of B{sub 4}C cylinders located inside and outside of the support barrel, respectively. The DORT3.1 two-dimensional transport code was used to evaluate the KALIMER shielding design. The reactor system was represented by four axial zones, each of which was modeled in the R-Z geometry. The KAFAX-F22 library was used in the analyses, which was generated from the JEF-2.2 of OECD/NEA files for LMR applications by KAERI. The performance of the KALIMER shielding design is compared against the shielding design criteria. The results indicate that the support barrel, upper grid plate, and other reactor structures meet the maximum neutron fluence and DPA limits established in the shielding design criteria. Activities of the air effluent in the PSDRS were also evaluated and are shown to satisfy the maximum permissible concentration (MPC) limits in 10 CFR Part 20. In the future, the validation of the DORT model by a detailed three dimensional calculation such as MCNP and the justification of the current shielding design limits are needed. (author). 13 refs., 23 figs., 31 tabs.

  13. Handling value added tax (VAT) in economic evaluations: should prices include VAT?

    Science.gov (United States)

    Bech, Mickael; Christiansen, Terkel; Gyrd-Hansen, Dorte

    2006-01-01

    In health economic evaluations, value added tax is commonly treated as a transfer payment. Following this argument, resources are valued equal to their net-of-tax prices in economic evaluations applying a societal perspective. In this article we argue that if there is the possibility that a new healthcare intervention may expand the healthcare budget, the social cost of input factors should be the gross-of-tax prices and not the net-of-tax prices. The rising interest in cost-benefit analysis and the use of absolute thresholds, net benefit estimates and acceptability curves in cost-effectiveness analysis makes this argument highly relevant for an appropriate use of these tools in prioritisation.

  14. Evaluation of Dogs with Border Collie Collapse, Including Response to Two Standardized Strenuous Exercise Protocols.

    Science.gov (United States)

    Taylor, Susan; Shmon, Cindy; Su, Lillian; Epp, Tasha; Minor, Katie; Mickelson, James; Patterson, Edward; Shelton, G Diane

    2016-01-01

    Clinical and metabolic variables were evaluated in 13 dogs with border collie collapse (BCC) before, during, and following completion of standardized strenuous exercise protocols. Six dogs participated in a ball-retrieving protocol, and seven dogs participated in a sheep-herding protocol. Findings were compared with 16 normal border collies participating in the same exercise protocols (11 retrieving, five herding). Twelve dogs with BCC developed abnormal mentation and/or an abnormal gait during evaluation. All dogs had post-exercise elevations in rectal temperature, pulse rate, arterial blood pH, PaO2, and lactate, and decreased PaCO2 and bicarbonate, as expected with strenuous exercise, but there were no significant differences between BCC dogs and normal dogs. Electrocardiography demonstrated sinus tachycardia in all dogs following exercise. Needle electromyography was normal, and evaluation of muscle biopsy cryosections using a standard panel of histochemical stains and reactions did not reveal a reason for collapse in 10 dogs with BCC in which these tests were performed. Genetic testing excluded the dynamin-1 related exercise-induced collapse mutation and the V547A malignant hyperthermia mutation as the cause of BCC. Common reasons for exercise intolerance were eliminated. Although a genetic basis is suspected, the cause of collapse in BCC was not determined.

  15. Ergonomic requirements to control room design - evaluation method

    International Nuclear Information System (INIS)

    Hinz, W.

    1985-01-01

    The method of evaluation introduced is the result of work carried out by the sub-committee 'Control Room Design' of the Engineering Standards Committee in DIN Standards, Ergonomy. This committee compiles standards for the design of control rooms (instrumentation and control) for the monitoring and operation of process engineering cycles. With the agreement of the committee - whom we wish to take the opportunity of thanking at this point for their constructive collaboration - a planned partial standard will be introduced thematically in the following, in order that knowledge gained from the discussion can be included in further work on the subject. The matter in question is a procedure for the qualitative evaluation of the duties to be performed under the control of operators in order that an assessment can be made of existing control concepts or such concepts as are to be found in the draft phase. (orig./GL) [de

  16. Evaluating and Using Literature Including People with Disabilities in All Classrooms

    Science.gov (United States)

    Oslick, Mary Ellen; Pearson, Mary

    2016-01-01

    To help students see their worlds differently and to expand those views beyond their own backyards, educators can expose them to quality multicultural children's literature. In this article, we focus on a subtopic within the genre of multicultural children's literature: literature including people with disabilities. We chose seven recent texts…

  17. A review of a radioactive material shipping container including design, testing, upgrading compliance program and shipping logistics

    International Nuclear Information System (INIS)

    Celovsky, A.; Lesco, R.; Gale, B.; Sypes, J.

    2003-01-01

    Ten years ago Atomic Energy of Canada developed a Type B(U)-85 shipping container for the global transport of highly radioactive materials. This paper reviews the development of the container, including a summary of the design requirements, a review of the selected materials and key design elements, and the results of the major qualification tests (drop testing, fire test, leak tightness testing, and shielding integrity tests). As a result of the testing, improvements to the structural, thermal and containment design were made. Such improvements, and reasons thereof, are noted. Also provided is a summary of the additional analysis work required to upgrade the package from a Type B(U) to a Type B(F), i.e. essentially upgrading the container to include fissile radioisotopes to the authorized radioactive contents list. Having a certified shipping container is only one aspect governing the global shipments of radioactive material. By necessity the shipment of radioactive material is a highly regulated environment. This paper also explores the experiences with other key aspects of radioactive shipments, including the service procedures used to maintain the container certification, the associated compliance program for radioactive material shipments, and the shipping logistics involved in the transport. (author)

  18. Evaluation of the vitreous matrices to include high-level radioactive wastes

    International Nuclear Information System (INIS)

    Varani, J.L.; Petraitis, E.J.; Pasquali, R.C.

    1987-01-01

    The Argentine Nuclear Programme considers a fuel cycle with Pu recycle. This will generate high-level liquid wastes, that should be safely eliminated. With this purpose, primary glasses utilizing three prototipe compositions were prepared. Simulated wastes oxides in the rate of about 10% were added to the vitreous matrices. The mixture was melted in ceramic melting pots in a muffle furnace at 1 100 deg C during 8 hours. Resistance leaching tests were made following an adaptation of the DIN 12 111 standard. Quantitative analysis of the leaching solutions were made to evaluate the solubility of the different elements. Glasses were observed with optical microscopy scanning before and after leaching. In the first, glasses, bubbles and crystalline-phase appear; in the second ones, puncture and embrittlement were detected. By means of differential thermoanalysis, endo and exothermal peaks were identified in glasses supporting gradual heating. X ray diffraction analysis were made in samples with and without wastes. The degree of crystallization of samples was evaluated by photographic and diffractometric techniques. Leaching studies showed the existance of a direct relation between leaching and glass alkaline content. (M.E.L.) [es

  19. Evaluation of the Treatment of Congenital Penile Curvature Including Psychosexual Assessment.

    Science.gov (United States)

    Zachalski, Wojciech; Krajka, Kazimierz; Matuszewski, Marcin

    2015-08-01

    Penile corporoplasty is a well-established treatment method of congenital penile deviation (CPD). Anatomical results are good with only slight differences between surgical procedures used. The disease however has huge influence on young male quality of life. This issue is not well analyzed in the literature. The aim of the study was to evaluate quality of life of the patients affected with CPD before and after the surgical treatment Study population consisted of 107 patients with CPD referred for surgical management. Patients were evaluated with not only clinical assessment, but also by four questionnaires measuring various aspects of quality of life. They were: Short-Form Medical Outcomes, Sexual Quality of Life Questionnaire for Man, Beck Depression Inventory, and International Index of Erectile Function. Quality of life measurements showed deep decrease in the general quality of life, sexual performance, depression scale, as well as in physical and mental health in men with CPD. All these parameters were restored to normal after the successful surgical treatment with any method. CPD deeply decreases the quality of life of the affected men in many aspects. Surgical treatment is able to repair the anatomical deformity and as well as significantly restore the patients' psychosocial well-being. © 2015 International Society for Sexual Medicine.

  20. Children and adolescents' internal models of food-sharing behavior include complex evaluations of contextual factors.

    Science.gov (United States)

    Markovits, Henry; Benenson, Joyce F; Kramer, Donald L

    2003-01-01

    This study examined internal representations of food sharing in 589 children and adolescents (8-19 years of age). Questionnaires, depicting a variety of contexts in which one person was asked to share a resource with another, were used to examine participants' expectations of food-sharing behavior. Factors that were varied included the value of the resource, the relation between the two depicted actors, the quality of this relation, and gender. Results indicate that internal models of food-sharing behavior showed systematic patterns of variation, demonstrating that individuals have complex contextually based internal models at all ages, including the youngest. Examination of developmental changes in use of individual patterns is consistent with the idea that internal models reflect age-specific patterns of interactions while undergoing a process of progressive consolidation.

  1. Including public perception data in the evaluation of the consequences of sewerage derived urban flooding.

    Science.gov (United States)

    Arthur, Scott; Crow, Helen; Karikas, Naoum

    2009-01-01

    This text reports research which was undertaken to assess the failure consequences associated with sewerage systems. In an effort to move away from considering only flood volume, depth or extent, the text will focus on how a survey of public opinion was used to inform the development of a consequence scoring methodology. The failure consequences considered range from internal flooding of properties, to road closure, environmental damage and odour problems. The text reports the extent to which experience of flooding influences perceptions of failure consequence and sewerage system management. It is also outlined how this data was used, along with other data sources, to construct an objective scoring process that can be used to evaluate failure consequence and readily prioritise sewerage maintenance.

  2. A Comprehensive Framework for Evaluation in Design Science Research

    DEFF Research Database (Denmark)

    Pries-Heje, Jan; Baskerville, Richard; Venable, John

    2012-01-01

    Evaluation is a central and essential activity in conducting rigorous Design Science Research (DSR), yet there is surprisingly little guidance about designing the DSR evaluation activity beyond suggesting possible methods that could be used for evaluation. This paper extends the notable exception...... of the existing framework of Pries-Heje et al [11] to address this problem. The paper proposes an extended DSR evaluation framework together with a DSR evaluation design method that can guide DSR researchers in choosing an appropriate strategy for evaluation of the design artifacts and design theories that form...... the output from DSR. The extended DSR evaluation framework asks the DSR researcher to consider (as input to the choice of the DSR evaluation strategy) contextual factors of goals, conditions, and constraints on the DSR evaluation, e.g. the type and level of desired rigor, the type of artifact, the need...

  3. Stepped-wedge cluster randomised controlled trials: a generic framework including parallel and multiple-level designs.

    Science.gov (United States)

    Hemming, Karla; Lilford, Richard; Girling, Alan J

    2015-01-30

    Stepped-wedge cluster randomised trials (SW-CRTs) are being used with increasing frequency in health service evaluation. Conventionally, these studies are cross-sectional in design with equally spaced steps, with an equal number of clusters randomised at each step and data collected at each and every step. Here we introduce several variations on this design and consider implications for power. One modification we consider is the incomplete cross-sectional SW-CRT, where the number of clusters varies at each step or where at some steps, for example, implementation or transition periods, data are not collected. We show that the parallel CRT with staggered but balanced randomisation can be considered a special case of the incomplete SW-CRT. As too can the parallel CRT with baseline measures. And we extend these designs to allow for multiple layers of clustering, for example, wards within a hospital. Building on results for complete designs, power and detectable difference are derived using a Wald test and obtaining the variance-covariance matrix of the treatment effect assuming a generalised linear mixed model. These variations are illustrated by several real examples. We recommend that whilst the impact of transition periods on power is likely to be small, where they are a feature of the design they should be incorporated. We also show examples in which the power of a SW-CRT increases as the intra-cluster correlation (ICC) increases and demonstrate that the impact of the ICC is likely to be smaller in a SW-CRT compared with a parallel CRT, especially where there are multiple levels of clustering. Finally, through this unified framework, the efficiency of the SW-CRT and the parallel CRT can be compared. © 2014 The Authors. Statistics in Medicine Published by John Wiley & Sons Ltd.

  4. Evaluation of field test kits including immunoassays for the detection of contaminants in soil and water

    International Nuclear Information System (INIS)

    Waters, L.C.; Smith, R.R.; Counts, R.W.; Stewart, J.H.; Jenkins, R.A.

    1993-01-01

    Effective field test methods are needed for hazardous waste site characterization and remediation. Useful field methods should be rapid, analyte-specific, cost-effective and accurate in the concentration range at which the analyte is regulated. In this study, field test kits for polychlorinated biphenyls (PCBs), mercury, lead and nitrate were evaluated with reference to these criteria. PCBs and mercury, in soils, were analyzed by immunoassay. Ionic lead and nitrate, in water, were measured chemically using test strips. Except for lead, each analyte was measured in both spiked and actual field samples. Twenty to 40 samples per day can be analyzed with the immunoassays and even more with the strip tests. The sensitivity of the immunoassays is in the 1-3 ppM range. Nitrate was consistently detected at ≥5 ppM; lead ions at ≥20 ppM. Results obtained using these methods compared favorably with those obtained by standard laboratory methods. In addition to being useful field screening methods, these kits can be used in the laboratory to sort out negative samples and/or to define proper dilutions for positive samples requiring further analysis

  5. Screening for Specific Language Impairment in Preschool Children: Evaluating a Screening Procedure Including the Token Test.

    Science.gov (United States)

    Willinger, Ulrike; Schmoeger, Michaela; Deckert, Matthias; Eisenwort, Brigitte; Loader, Benjamin; Hofmair, Annemarie; Auff, Eduard

    2017-10-01

    Specific language impairment (SLI) comprises impairments in receptive and/or expressive language. Aim of this study was to evaluate a screening for SLI. 61 children with SLI (SLI-children, age-range 4-6 years) and 61 matched typically developing controls were tested for receptive language ability (Token Test-TT) and for intelligence (Wechsler Preschool-and-Primary-Scale-of-Intelligence-WPPSI). Group differences were analyzed using t tests, as well as direct and stepwise discriminant analyses. The predictive value of the WPPSI with respect to TT performance was analyzed using regression analyses. SLI-children performed significantly worse on both TT and WPPSI ([Formula: see text]). The TT alone yielded an overall classification rate of 79%, the TT and the WPPSI together yielded an overall classification rate of 80%. TT performance was significantly predicted by verbal intelligence in SLI-children and nonverbal intelligence in controls whilst WPPSI subtest arithmetic was predictive in both groups. Without further research, the Token Test cannot be seen as a valid and sufficient tool for the screening of SLI in preschool children but rather as a tool for the assessment of more general intellectual capacities. SLI-children at this age already show impairments typically associated with SLI which indicates the necessity of early developmental support or training. Token Test performance is possibly an indicator for a more general developmental factor rather than an exclusive indicator for language difficulties.

  6. Design, Construction and Evaluation of a Dry Solar Sterilizer

    International Nuclear Information System (INIS)

    Hernández Fereira, Arcelio A.

    2017-01-01

    The objective of the work was the search of an alternative for sterilization using solar energy. For such purposes, a dry solar sterilizer of 4276 cm3 capacity was designed, constructed and evaluated. Potential users would be rural medical posts in areas without electricity, health posts in military units under field conditions, and experimental microbiology stations. The evaluation included the determination of the energy efficiency of the sterilizer, the economic evaluation against other variants and the biological safety assessment. The developed equipment reached the sterilization temperature for levels of the direct component of the solar radiation higher than 300 W/m2 in 14 minutes, corresponding to an average heating rate of 13 0C/minute, higher than that of an electric furnace. Its energy efficiency with direct solar radiation of 310.5 W/m2 was 53.79%. The equipment is of easy construction, simple operation and very low cost. (author)

  7. Designing, Implementing, and Evaluating Secure Web Browsers

    Science.gov (United States)

    Grier, Christopher L.

    2009-01-01

    Web browsers are plagued with vulnerabilities, providing hackers with easy access to computer systems using browser-based attacks. Efforts that retrofit existing browsers have had limited success since modern browsers are not designed to withstand attack. To enable more secure web browsing, we design and implement new web browsers from the ground…

  8. Ergonomic evaluation of pilot oxygen mask designs

    NARCIS (Netherlands)

    Lee, W.; Yang, Xiaopeng; Jung, Daehan; Park, Seikwon; Kim, Heeeun; You, Heecheon

    2018-01-01

    A revised pilot oxygen mask design was developed for better fit to the Korean Air Force pilots’ faces. The present study compared an existing pilot oxygen mask and a prototype of the revised mask design with 88 Korean Air Force pilots in terms of subjective discomfort, facial contact pressure,

  9. Evaluation in Design-Oriented Research

    NARCIS (Netherlands)

    Verschuren, P.J.M.; Hartog, R.J.M.

    2005-01-01

    Design has been recognized for a long time both as art and as science. In the sixties of the previous century design-oriented research began to draw the attention of scientific researchers and methodologists, not only in technical engineering but also in the social sciences. However, a rather

  10. Defining robustness protocols: a method to include and evaluate robustness in clinical plans

    International Nuclear Information System (INIS)

    McGowan, S E; Albertini, F; Lomax, A J; Thomas, S J

    2015-01-01

    We aim to define a site-specific robustness protocol to be used during the clinical plan evaluation process. Plan robustness of 16 skull base IMPT plans to systematic range and random set-up errors have been retrospectively and systematically analysed. This was determined by calculating the error-bar dose distribution (ebDD) for all the plans and by defining some metrics used to define protocols aiding the plan assessment. Additionally, an example of how to clinically use the defined robustness database is given whereby a plan with sub-optimal brainstem robustness was identified. The advantage of using different beam arrangements to improve the plan robustness was analysed. Using the ebDD it was found range errors had a smaller effect on dose distribution than the corresponding set-up error in a single fraction, and that organs at risk were most robust to the range errors, whereas the target was more robust to set-up errors. A database was created to aid planners in terms of plan robustness aims in these volumes. This resulted in the definition of site-specific robustness protocols. The use of robustness constraints allowed for the identification of a specific patient that may have benefited from a treatment of greater individuality. A new beam arrangement showed to be preferential when balancing conformality and robustness for this case. The ebDD and error-bar volume histogram proved effective in analysing plan robustness. The process of retrospective analysis could be used to establish site-specific robustness planning protocols in proton therapy. These protocols allow the planner to determine plans that, although delivering a dosimetrically adequate dose distribution, have resulted in sub-optimal robustness to these uncertainties. For these cases the use of different beam start conditions may improve the plan robustness to set-up and range uncertainties. (paper)

  11. Defining robustness protocols: a method to include and evaluate robustness in clinical plans

    Science.gov (United States)

    McGowan, S. E.; Albertini, F.; Thomas, S. J.; Lomax, A. J.

    2015-04-01

    We aim to define a site-specific robustness protocol to be used during the clinical plan evaluation process. Plan robustness of 16 skull base IMPT plans to systematic range and random set-up errors have been retrospectively and systematically analysed. This was determined by calculating the error-bar dose distribution (ebDD) for all the plans and by defining some metrics used to define protocols aiding the plan assessment. Additionally, an example of how to clinically use the defined robustness database is given whereby a plan with sub-optimal brainstem robustness was identified. The advantage of using different beam arrangements to improve the plan robustness was analysed. Using the ebDD it was found range errors had a smaller effect on dose distribution than the corresponding set-up error in a single fraction, and that organs at risk were most robust to the range errors, whereas the target was more robust to set-up errors. A database was created to aid planners in terms of plan robustness aims in these volumes. This resulted in the definition of site-specific robustness protocols. The use of robustness constraints allowed for the identification of a specific patient that may have benefited from a treatment of greater individuality. A new beam arrangement showed to be preferential when balancing conformality and robustness for this case. The ebDD and error-bar volume histogram proved effective in analysing plan robustness. The process of retrospective analysis could be used to establish site-specific robustness planning protocols in proton therapy. These protocols allow the planner to determine plans that, although delivering a dosimetrically adequate dose distribution, have resulted in sub-optimal robustness to these uncertainties. For these cases the use of different beam start conditions may improve the plan robustness to set-up and range uncertainties.

  12. Prospective evaluation of dermatologic surgery complications including patients on multiple antiplatelet and anticoagulant medications.

    Science.gov (United States)

    Bordeaux, Jeremy S; Martires, Kathryn J; Goldberg, Dori; Pattee, Sean F; Fu, Pingfu; Maloney, Mary E

    2011-09-01

    Few prospective studies have evaluated the safety of dermatologic surgery. We sought to determine rates of bleeding, infection, flap and graft necrosis, and dehiscence in outpatient dermatologic surgery, and to examine their relationship to type of repair, anatomic location of repair, antibiotic use, antiplatelet use, or anticoagulant use. Patients presenting to University of Massachusetts Medical School Dermatology Clinic for surgery during a 15-month period were prospectively entered. Medications, procedures, and complications were recorded. Of the 1911 patients, 38% were on one anticoagulant or antiplatelet medication, and 8.0% were on two or more. Risk of hemorrhage was 0.89%. Complex repair (odds ratio [OR] = 5.80), graft repair (OR = 7.58), flap repair (OR = 11.93), and partial repair (OR = 43.13) were more likely to result in bleeding than intermediate repair. Patients on both clopidogrel and warfarin were 40 times more likely to have bleeding complications than all others (P = .03). Risk of infection was 1.3%, but was greater than 3% on the genitalia, scalp, back, and leg. Partial flap necrosis occurred in 1.7% of flaps, and partial graft necrosis occurred in 8.6% of grafts. Partial graft necrosis occurred in 20% of grafts on the scalp and 10% of grafts on the nose. All complications resolved without sequelae. The study was limited to one academic dermatology practice. The rate of complications in dermatologic surgery is low, even when multiple oral anticoagulant and antiplatelet medications are continued, and prophylactic antibiotics are not used. Closure type and use of warfarin or clopidogrel increase bleeding risk. However, these medications should be continued to avoid adverse thrombotic events. Copyright © 2011 American Academy of Dermatology, Inc. Published by Mosby, Inc. All rights reserved.

  13. Noninvasive model including right ventricular speckle tracking for the evaluation of pulmonary hypertension.

    Science.gov (United States)

    Mahran, Yossra; Schueler, Robert; Weber, Marcel; Pizarro, Carmen; Nickenig, Georg; Skowasch, Dirk; Hammerstingl, Christoph

    2016-08-26

    To find parameters from transthorathic echocardiography (TTE) including speckle-tracking (ST) analysis of the right ventricle (RV) to identify precapillary pulmonary hypertension (PH). Forty-four patients with suspected PH undergoing right heart catheterization (RHC) were consecutively included (mean age 63.1 ± 14 years, 61% male gender). All patients underwent standardized TTE including ST analysis of the RV. Based on the subsequent TTE-derived measurements, the presence of PH was assessed: Left ventricular ejection fraction (LVEF) was calculated by Simpsons rule from 4Ch. Systolic pulmonary artery pressure (sPAP) was assessed with continuous wave Doppler of systolic tricuspid regurgitant velocity and regarded raised with values ≥ 30 mmHg as a surrogate parameter for RA pressure. A concomitantly elevated PCWP was considered a means to discriminate between the precapillary and postcapillary form of PH. PCWP was considered elevated when the E/e' ratio was > 12 as a surrogate for LV diastolic pressure. E/e' ratio was measured by gauging systolic and diastolic velocities of the lateral and septal mitral valve annulus using TDI mode. The results were then averaged with conventional measurement of mitral valve inflow. Furthermore, functional testing with six minutes walking distance (6MWD), ECG-RV stress signs, NT pro-BNP and other laboratory values were assessed. PH was confirmed in 34 patients (precapillary PH, n = 15, postcapillary PH, n = 19). TTE showed significant differences in E/e' ratio (precapillary PH: 12.3 ± 4.4, postcapillary PH: 17.3 ± 10.3, no PH: 12.1 ± 4.5, P = 0.02), LV volumes (ESV: 25.0 ± 15.0 mL, 49.9 ± 29.5 mL, 32.2 ± 13.6 mL, P = 0.027; EDV: 73.6 ± 24.0 mL, 110.6 ± 31.8 mL, 87.8 ± 33.0 mL, P = 0.021) and systolic pulmonary arterial pressure (sPAP: 61.2 ± 22.3 mmHg, 53.6 ± 20.1 mmHg, 31.2 ± 24.6 mmHg, P = 0.001). STRV analysis showed significant differences for apical RV longitudinal strain (RVAS: -7.5% ± 5.6%, -13.3% ± 4.3%, -14

  14. Closed-form solutions for linear regulator-design of mechanical systems including optimal weighting matrix selection

    Science.gov (United States)

    Hanks, Brantley R.; Skelton, Robert E.

    1991-01-01

    This paper addresses the restriction of Linear Quadratic Regulator (LQR) solutions to the algebraic Riccati Equation to design spaces which can be implemented as passive structural members and/or dampers. A general closed-form solution to the optimal free-decay control problem is presented which is tailored for structural-mechanical systems. The solution includes, as subsets, special cases such as the Rayleigh Dissipation Function and total energy. Weighting matrix selection is a constrained choice among several parameters to obtain desired physical relationships. The closed-form solution is also applicable to active control design for systems where perfect, collocated actuator-sensor pairs exist. Some examples of simple spring mass systems are shown to illustrate key points.

  15. Designing and Evaluating Students' Transformative Learning

    Directory of Open Access Journals (Sweden)

    Nina B. Namaste

    2017-12-01

    Full Text Available Transformative learning hinges on navigating cognitive dissonance; thus, intercultural competency assignments and experiences need to be integrated into study abroad/away courses to help students process and make sense of the cognitive dissonance such an experience provides. Assignments, therefore, need to consciously and intentionally triangulate learning by addressing the read (course readings, the lived/observed (conversations, interactions, activities, excursions, observations about public portrayals of culture, etc., and the compared (home culture vs. host culture. The hope is to improve students’ experiences so that semesters abroad are consistently deep, enriching, and intellectual as opposed to simply an extended tourist sojourn. This article documents the process by which I designed for and assessed, via an in-depth analysis of students’ texts/writings, students’ transformation of their intercultural competency skills and development. In addition, I compared students’ works from two differing semesters to evaluate whether transformation in intercultural competency is inherent in the nature of study abroad or must be explicitly taught and cultivated. My Scholarship of Teaching and Learning (SoTL project corroborated the almost ten years of research that confirm our fears: exposure to another culture is not enough; studying and living abroad does not necessarily lead to increased intercultural learning. Meaningful, integrative, “learning-laden,” and transformative study abroad experiences hinge on students’ ability to make sense of cognitive dissonance. Intercultural competency assignments, therefore, need to be fully and intentionally designed and integrated into such experiences, and evaluated to document such growth. L’apprentissage transformationnel repose sur la manière de naviguer la dissonance cognitive. Par conséquent, les devoirs qui traitent de la compétence interculturelle ainsi que les expériences n

  16. Economic evaluation of angiographic interventions including a whole-radiology in- and outpatient care

    International Nuclear Information System (INIS)

    Nolte-Ernsting, C.; Abel, K.; Krupski, G.; Lorenzen, J.; Adam, G.

    2006-01-01

    Purpose: To determine the economic efficiency of a whole-radiology in- and outpatient treatment with angiographic interventions performed as the main or sole therapy. Materials and Methods: The calculations represent the data of a university radiology department, including the following angiographic interventions (neuroradiology not considered): Vascular intervention (PTA, stent implantation) of kidneys and extremities, recanalization of hemodialysis access, chemoembolization, diagnostic arterioportal liver CT, port implantation, varicocele embolization, PTCD, percutaneous implantation of biliary stent. First, the different angiographic interventions are categorized with reference to the German DRG system 2005. Considering the example of a university hospital, the individual cost of each intervention is calculated and correlated with reimbursements by G-DRG2005 and so-called ''ambulant operation'' (EBM200plus). With these data, profits and losses are calculated for both in- and outpatient care. Results: Radiologic interventions of inpatients yield a profit in the majority of cases. With a base rate of 2900 Euro, the profits in our university hospital range between -872 Euro and +3411 Euro (mean: +1348 Euro). On the other hand, those angiographic interventions suitable for ''ambulant operation'' generate average profits of +372 Euro, if only direct costs are considered. The data of outpatient radiological interventions average between 381 Euro up to 1612 Euro lower than compared with profits obtained from in patient care. (orig.)

  17. Dosimetric evaluation of three adaptive strategies for prostate cancer treatment including pelvic lymph nodes irradiation.

    Science.gov (United States)

    Cantin, Audrey; Gingras, Luc; Lachance, Bernard; Foster, William; Goudreault, Julie; Archambault, Louis

    2015-12-01

    The movements of the prostate relative to the pelvic lymph nodes during intensity-modulated radiation therapy treatment can limit margin reduction and affect the protection of the organs at risk (OAR). In this study, the authors performed an analysis of three adaptive treatment strategies that combine information from both bony and gold marker registrations. The robustness of those treatments against the interfraction prostate movements was evaluated. A retrospective study was conducted on five prostate cancer patients with 7-13 daily cone-beam CTs (CBCTs). The clinical target volumes (CTVs) consisting of pelvic lymph nodes, prostate, and seminal vesicles as well as the OARs were delineated on each CBCT and the initial CT. Three adaptive strategies were analyzed. Two of these methods relied on a two-step patient positioning at each fraction. First step: a bony registration was used to deliver the nodal CTV prescription. Second step: a gold marker registration was then used either to (1) complete the dose delivered to the prostate (complement); (2) or give almost the entire prescription to the prostate with a weak dose gradient between the targets to compensate for possible motions (gradient). The third method (COR) used a pool of precalculated plans based on images acquired at previous treatment fractions. At each new fraction, a plan is selected from that pool based on the daily position of prostate center-of-mass. The dosimetric comparison was conducted and results are presented with and without the systematic shift in the prostate position on the CT planning. The adaptive strategies were compared to the current clinical standard where all fractions are treated with the initial nonadaptive plan. The minimum daily prostate D95% is improved by 2%, 9%, and 6% for the complement, the gradient, and the COR approaches, respectively, compared to the nonadaptive method. The average nodal CTV D95% remains constant across the strategies, except for the gradient approach

  18. Dosimetric evaluation of three adaptive strategies for prostate cancer treatment including pelvic lymph nodes irradiation

    International Nuclear Information System (INIS)

    Cantin, Audrey; Gingras, Luc; Archambault, Louis; Lachance, Bernard; Foster, William; Goudreault, Julie

    2015-01-01

    Purpose: The movements of the prostate relative to the pelvic lymph nodes during intensity-modulated radiation therapy treatment can limit margin reduction and affect the protection of the organs at risk (OAR). In this study, the authors performed an analysis of three adaptive treatment strategies that combine information from both bony and gold marker registrations. The robustness of those treatments against the interfraction prostate movements was evaluated. Methods: A retrospective study was conducted on five prostate cancer patients with 7–13 daily cone-beam CTs (CBCTs). The clinical target volumes (CTVs) consisting of pelvic lymph nodes, prostate, and seminal vesicles as well as the OARs were delineated on each CBCT and the initial CT. Three adaptive strategies were analyzed. Two of these methods relied on a two-step patient positioning at each fraction. First step: a bony registration was used to deliver the nodal CTV prescription. Second step: a gold marker registration was then used either to (1) complete the dose delivered to the prostate (complement); (2) or give almost the entire prescription to the prostate with a weak dose gradient between the targets to compensate for possible motions (gradient). The third method (COR) used a pool of precalculated plans based on images acquired at previous treatment fractions. At each new fraction, a plan is selected from that pool based on the daily position of prostate center-of-mass. The dosimetric comparison was conducted and results are presented with and without the systematic shift in the prostate position on the CT planning. The adaptive strategies were compared to the current clinical standard where all fractions are treated with the initial nonadaptive plan. Results: The minimum daily prostate D 95% is improved by 2%, 9%, and 6% for the complement, the gradient, and the COR approaches, respectively, compared to the nonadaptive method. The average nodal CTV D 95% remains constant across the strategies

  19. Fever in trauma patients: evaluation of risk factors, including traumatic brain injury.

    Science.gov (United States)

    Bengualid, Victoria; Talari, Goutham; Rubin, David; Albaeni, Aiham; Ciubotaru, Ronald L; Berger, Judith

    2015-03-01

    The role of fever in trauma patients remains unclear. Fever occurs as a response to release of cytokines and prostaglandins by white blood cells. Many factors, including trauma, can trigger release of these factors. To determine whether (1) fever in the first 48 hours is related to a favorable outcome in trauma patients and (2) fever is more common in patients with head trauma. Retrospective study of trauma patients admitted to the intensive care unit for at least 2 days. Data were analyzed by using multivariate analysis. Of 162 patients studied, 40% had fever during the first 48 hours. Febrile patients had higher mortality rates than did afebrile patients. When adjusted for severity of injuries, fever did not correlate with mortality. Neither the incidence of fever in the first 48 hours after admission to the intensive care unit nor the number of days febrile in the unit differed between patients with and patients without head trauma (traumatic brain injury). About 70% of febrile patients did not have a source found for their fever. Febrile patients without an identified source of infection had lower peak white blood cell counts, lower maximum body temperature, and higher minimum platelet counts than did febrile patients who had an infectious source identified. The most common infection was pneumonia. No relationship was found between the presence of fever during the first 48 hours and mortality. Patients with traumatic brain injury did not have a higher incidence of fever than did patients without traumatic brain injury. About 30% of febrile patients had an identifiable source of infection. Further studies are needed to understand the origin and role of fever in trauma patients. ©2015 American Association of Critical-Care Nurses.

  20. Study design considerations in evaluating environmental impacts

    Science.gov (United States)

    Stan T. Lebow; Paul A. Cooper; Patricia Lebow

    2006-01-01

    The purpose of this chapter is to make the reader aware of how choices in study parameters may influence the outcome of treated-wood environmental impact evaluations. Evaluation of the leaching and environmental accumulation of preservatives from treated wood is a complex process. and many factors can influence the results of such studies. In laboratory studies, the...

  1. Evaluating Plot Designs for the Tropics

    Science.gov (United States)

    Paul C. van Deusen; Bruce Bayle

    1991-01-01

    Theory and procedures are reviewed for determining the best type of plot for a given forest inventory. A general methodology is given that clarifies the relationship between different plot designs and the associated methods to produce the inventory estimates.

  2. Experimental evaluation of admission and disposition of artificial radionuclides including transuranium elements in agricultural plants

    Energy Technology Data Exchange (ETDEWEB)

    Kozhakhanov, T.; Lukashenko, S. [Institute of radiation safety and ecology (Kazakhstan)

    2014-07-01

    Processes of radionuclides migration and transfer to agricultural plants are quite well developed worldwide, but the information on character of accumulation of {sup 241}Am and {sup 239+240}Pu transuranium radionuclides in agricultural plants is still fragmentary. Even in generalized materials of worldwide studies, IAEA guide, accumulation coefficient (AC) can have wide range of values (5-6 orders), no data exists on radionuclides' distribution in different organs of plants and they are given for joined groups of plants and types of soils. That is why the main aim of this work was to obtain basic quantitative parameters of radionuclides' migration in 'soil-plant' system, and firs of all- for transuranium elements.. In 2010 a series of experiments with agricultural plants was started at the territory of the former Semipalatinsk Test Site aimed to investigate entry of artificial radionuclides by crop products in natural climatic conditions. To conduct the experiment for study of coefficient of radionuclides' accumulation by agricultural corps, there was chosen a land spot at the STS territory, characterized by high concentration of radionuclides: {sup 241}Am - n*10{sup 4} Bq/kg, {sup 137}Cs - n*10{sup 3} Bq/kg, {sup 90}Sr - n*10{sup 3} Bq/kg and {sup 239+240}Pu- n*10{sup 5} Bq/kg. As objects of investigation, cultures, cultivated in Kazakhstan have been selected: wheat (Triticum vulgare), barley (Hordeum vulgare), oat (Avena sativa L.), water melon (Citrullus vulgaris), melon (Cucumis melo), potato (Solanum tuberosum), eggplant (Solanum melongena), pepper (Capsicum annuum), tomato (Solanum lycopersicum), sunflower (Helianthus cultus), onion (Allium cepa), carrot (Daucus carota), parsley(Petroselinum vulgare)and cabbage (Brassica oleracea). Investigated plants have been planted within the time limits, recommended for selected types of agricultural plants. Cropping system included simple agronomic and amelioration measures. Fertilizers were not

  3. Interfacial Micromechanics in Fibrous Composites: Design, Evaluation, and Models

    Science.gov (United States)

    Lei, Zhenkun; Li, Xuan; Qin, Fuyong; Qiu, Wei

    2014-01-01

    Recent advances of interfacial micromechanics in fiber reinforced composites using micro-Raman spectroscopy are given. The faced mechanical problems for interface design in fibrous composites are elaborated from three optimization ways: material, interface, and computation. Some reasons are depicted that the interfacial evaluation methods are difficult to guarantee the integrity, repeatability, and consistency. Micro-Raman study on the fiber interface failure behavior and the main interface mechanical problems in fibrous composites are summarized, including interfacial stress transfer, strength criterion of interface debonding and failure, fiber bridging, frictional slip, slip transition, and friction reloading. The theoretical models of above interface mechanical problems are given. PMID:24977189

  4. Parametric evaluation of an SMR design domain

    International Nuclear Information System (INIS)

    Al Rashdan, Ahmad; Tsvetkov, Pavel

    2015-01-01

    Highlights: • The design of nuclear reactors involves a large set of highly coupled variables. • The effects of 14 variables on 6 SMR performance characteristics was researched. • Screening and sensitivity analyses were applied to decouple the variables’ effects. • Significantly simpler system models were generated, enabling simple optimization. - Abstract: The complex and coupled behavior of the variables that affect the currently developing generation IV reactors and the increase of interest in Small Modular Reactors are major incentives to seek efficient design methods. Instead of the brute force design methodology, often applied to the analysis of nuclear reactors, other more economical and systematic methods should be applied. In a complex system with a high number of variables, it often is necessary to develop models to describe the behavior of each performance characteristic with respect to a set of variables and their interactions. If expensive experiments are needed to develop these models, the number of experiments should be minimized. This can be achieved by designing the experiments to be performed. Once the system’s models are developed, they can be used to decouple the variables’ effects on the performance characteristics and simplify the optimization process. In this article, three screening and sensitivity analysis methods are applied to decouple and understand the effects of fourteen variables on six performance characteristics of a Small Modular Reactor’s design, based on the Advanced Passive (AP-1000) reactor. The application of these methods facilitated the determination of the most important parameters of each performance characteristic, and resulted in several distinctive findings. These findings are applicable to any Light Water Small Modular Reactor that falls within the variables’ design domain

  5. Crew Transportation Technical Standards and Design Evaluation Criteria

    Science.gov (United States)

    Lueders, Kathryn L.; Thomas, Rayelle E. (Compiler)

    2015-01-01

    Crew Transportation Technical Standards and Design Evaluation Criteria contains descriptions of technical, safety, and crew health medical processes and specifications, and the criteria which will be used to evaluate the acceptability of the Commercial Providers' proposed processes and specifications.

  6. Performance evaluation of seal coat materials and designs.

    Science.gov (United States)

    2011-01-01

    "This project presents an evaluation of seal coat materials and design method. The primary objectives of this research are 1) to evaluate seal coat performance : from various combinations of aggregates and emulsions in terms of aggregate loss; 2) to ...

  7. Design, Construction and Performance Evaluation of Multiple ...

    African Journals Online (AJOL)

    The complex casting machine has been designed to perform the following techniques: gravity casting, stir casting, squeeze casting, vacuum casting, compocasting and thixoforming. All these casting techniques have been integrated into this complex casting machine as different units which work with the help of automation.

  8. Arthroscopic sheath design and technical evaluation

    NARCIS (Netherlands)

    Tuijthof, Gabriëlle J. M.; Blankevoort, Leendert; Herder, Just L.; van Dijk, C. Niek

    2009-01-01

    The maintenance of a clear view on the operation area is essential to perform a minimally invasive procedure In arthroscopy, this is achieved by irrigating the Joint with a saline fluid that is pumped through the joint At present the arthroscopic sheaths are not designed for optimal irrigation,

  9. User Evaluation of Neonatology Ward Design.

    Science.gov (United States)

    Trujillo, Juan Luis Higuera; Aviñó, Antoni Montañana I; Millán, Carmen Llinares

    2017-01-01

    The object of this article is to identify the set of affective and emotional factors behind users' assessments of a space in a neonatology unit and to propose design guidelines based on these. The importance of the neonatology service and the variety of users place great demands on the space at all levels. Despite the repercussions, the emotional aspects of the environment have received less attention. To avoid incurring limitations in the user mental scheme, this study uses two complementary methodologies: focus group and semantic differential. The (qualitative) focus group methodology provides exploratory information and concepts. The (quantitative) semantic differential methodology then uses these concepts to extract the conceptual structures that users employ in their assessment of the space. Of the total 175 subjects, 31 took part in focus groups and 144 in semantic differential. Five independent concepts were identified: privacy, functionality and professional nature, spaciousness, lighting, and cleanliness. In relation to the importance of the overall positive assessment of the space, the perception of privacy and sensations of dominance and pleasure are fundamental. Six relevant design aspects were also identified: provide spacious surroundings, facilitate sufficient separation between the different posts or cots, use different colors from those usually found in health-care centers, as some aversion was found to white and especially green, design areas with childhood themes, use warm artificial light, and choose user-friendly equipment. Results provide design recommendations of interest and show the possibilities offered by combining both systems to analyze user response.

  10. Evaluation of the DRAGON code for VHTR design analysis.

    Energy Technology Data Exchange (ETDEWEB)

    Taiwo, T. A.; Kim, T. K.; Nuclear Engineering Division

    2006-01-12

    This letter report summarizes three activities that were undertaken in FY 2005 to gather information on the DRAGON code and to perform limited evaluations of the code performance when used in the analysis of the Very High Temperature Reactor (VHTR) designs. These activities include: (1) Use of the code to model the fuel elements of the helium-cooled and liquid-salt-cooled VHTR designs. Results were compared to those from another deterministic lattice code (WIMS8) and a Monte Carlo code (MCNP). (2) The preliminary assessment of the nuclear data library currently used with the code and libraries that have been provided by the IAEA WIMS-D4 Library Update Project (WLUP). (3) DRAGON workshop held to discuss the code capabilities for modeling the VHTR.

  11. Evaluation of the DRAGON code for VHTR design analysis

    International Nuclear Information System (INIS)

    Taiwo, T. A.; Kim, T. K.; Nuclear Engineering Division

    2006-01-01

    This letter report summarizes three activities that were undertaken in FY 2005 to gather information on the DRAGON code and to perform limited evaluations of the code performance when used in the analysis of the Very High Temperature Reactor (VHTR) designs. These activities include: (1) Use of the code to model the fuel elements of the helium-cooled and liquid-salt-cooled VHTR designs. Results were compared to those from another deterministic lattice code (WIMS8) and a Monte Carlo code (MCNP). (2) The preliminary assessment of the nuclear data library currently used with the code and libraries that have been provided by the IAEA WIMS-D4 Library Update Project (WLUP). (3) DRAGON workshop held to discuss the code capabilities for modeling the VHTR

  12. CEPIAH, a method for Evaluation and Design of Pedagogical Hypermedia

    OpenAIRE

    Trigano , Philippe; Pacurar Giacomini , Ecaterina

    2004-01-01

    We are working on a method, called CEPIAH. We propose a web based system used to help teachers to design multimedia documents and to evaluate their prototypes. Our tool integrates two modules such as EMPI (Evaluation of Multimedia Pedagogical and Interactive software), and SP/UL/FC, a method for designing pedagogical hypermedia. The EMPI module is used to evaluate multimedia software used in educational context. We structured a knowledge base composed of a list of evaluation criteria, grouped...

  13. Design requirements for SRB production control system. Volume 3: Package evaluation, modification and hardware

    Science.gov (United States)

    1981-01-01

    The software package evaluation was designed to analyze commercially available, field-proven, production control or manufacturing resource planning management technology and software package. The analysis was conducted by comparing SRB production control software requirements and conceptual system design to software package capabilities. The methodology of evaluation and the findings at each stage of evaluation are described. Topics covered include: vendor listing; request for information (RFI) document; RFI response rate and quality; RFI evaluation process; and capabilities versus requirements.

  14. Comprehensive evaluation method in application of nuclear DCS product design

    International Nuclear Information System (INIS)

    Wang Weixin; Zhao Zhemin; Shi Yingbin

    2014-01-01

    In order to select the best design proposal in short time, the TOPSIS comprehensive evaluation method in the nuclear power plant DCS product design was introduced. It can intuitively show the different design proposals good or not good by data and shorten the time of the design proposal optimization. The design proposal selected by this method will be more reasonable and has good comprehensive performance indexes. The TOPSIS comprehensive evaluation method achieves good result in one of the nuclear power plant DCS cabinet design proposal optimization. (authors)

  15. Extension Sustainability Camp: Design, Implementation, and Evaluation

    Science.gov (United States)

    Brain, Roslynn; Upton, Sally; Tingey, Brett

    2015-01-01

    Sustainability Camps provide an opportunity for Extension educators to be in the forefront of sustainability outreach and to meet the growing demand for sustainability education. This article shares development, implementation, and evaluation of an Extension Sustainability Camp for youth, grades 4-6. Camp impact was measured via daily pre-and…

  16. Usability evaluations in user-centred design

    NARCIS (Netherlands)

    Ruyter, de B.E.R.; Vet, de J.H.M.

    1997-01-01

    Improving usability of consumer applications has been the focus of much research. Estimating the advantage of these efforts, however, still is very cumbersome since evaluating product improvements in terms of their usability requires good measuring methods and tools. In this paper activities in the

  17. Design of subjects training on reactor simulator and feasibility study - toward the empirical evaluation of interface design concept

    International Nuclear Information System (INIS)

    Yamaguchi, Y.; Furukawa, H.; Tanabe, F.

    1998-01-01

    On-going JAERI's project for empirical evaluation of the ecological interface design concept was first described. The empirical evaluation is planned to be proceeded through three consecutive steps; designing and actual implementation of the interface on reactor simulator, verification of the interface created, and the validation by the simulator experiment. For conducting the project, three different experimental resources are prerequisite, that are, data analysis method for identifying the operator's strategies, experimental facility including reactor simulator, and experimental subjects or subjects training method. Among the three experimental resources, subjects training method was recently designed and a simulator experiment was earned out in order to examine the feasibility of the designed training method. From the experiment and analysis of the experimental records, we could conclude that it is feasible that the experimental subjects having an appropriate technical basis can gain the sufficient competence for evaluation work of the interface design concept by using the training method designed. (author)

  18. Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

    DEFF Research Database (Denmark)

    Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

    2014-01-01

    the efficiency of machinery systems. The wet sulphuric acid process is an effective way of removing flue gas sulphur oxides from land-based coal-fired power plants. Moreover, organic Rankine cycles (ORC) are suitable for heat to power conversion for low temperature heat sources. This paper describes the design...... that an ORC placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase the combined cycle thermal efficiency by 2.6%. The findings indicate that the technology has potential in marine applications regarding both energy...... and modeling of a highly efficient machinery system which includes the removal of exhaust gas sulphur oxides. The system consists of a two-stroke diesel engine, the wet sulphuric process for sulphur removal, a conventional steam Rankine cycle and an ORC. Results of numerical modeling efforts suggest...

  19. Nonexpert Evaluations on Architectural Design Creativity across Cultures

    Science.gov (United States)

    Hong, Seung Wan; Lee, Jae Seung

    2015-01-01

    This article examines the relationship between cultural differences and the nonexpert evaluations of architectural design creativity. In study I, Caucasian Americans (N = 126) and East Asians (N = 137), who did not major in architecture and urban design, evaluated the novelty and appropriateness of 5 unusual architectural shapes, selected by 5…

  20. Evaluating camouflage design using eye movement data.

    Science.gov (United States)

    Lin, Chiuhsiang Joe; Chang, Chi-Chan; Lee, Yung-Hui

    2014-05-01

    This study investigates the characteristics of eye movements during a camouflaged target search task. Camouflaged targets were randomly presented on two natural landscapes. The performance of each camouflage design was assessed by target detection hit rate, detection time, number of fixations on display, first saccade amplitude to target, number of fixations on target, fixation duration on target, and subjective ratings of search task difficulty. The results showed that the camouflage patterns could significantly affect the eye-movement behavior, especially first saccade amplitude and fixation duration, and the findings could be used to increase the sensitivity of the camouflage assessment. We hypothesized that the assessment could be made with regard to the differences in detectability and discriminability of the camouflage patterns. These could explain less efficient search behavior in eye movements. Overall, data obtained from eye movements can be used to significantly enhance the interpretation of the effects of different camouflage design. Copyright © 2013 Elsevier Ltd and The Ergonomics Society. All rights reserved.

  1. Seismic design and evaluation criteria based on target performance goals

    International Nuclear Information System (INIS)

    Murray, R.C.; Nelson, T.A.; Kennedy, R.P.; Short, S.A.

    1994-04-01

    The Department of Energy utilizes deterministic seismic design/evaluation criteria developed to achieve probabilistic performance goals. These seismic design and evaluation criteria are intended to apply equally to the design of new facilities and to the evaluation of existing facilities. In addition, the criteria are intended to cover design and evaluation of buildings, equipment, piping, and other structures. Four separate sets of seismic design/evaluation criteria have been presented each with a different performance goal. In all these criteria, earthquake loading is selected from seismic hazard curves on a probabilistic basis but seismic response evaluation methods and acceptable behavior limits are deterministic approaches with which design engineers are familiar. For analytical evaluations, conservatism has been introduced through the use of conservative inelastic demand-capacity ratios combined with ductile detailing requirements, through the use of minimum specified material strengths and conservative code capacity equations, and through the use of a seismic scale factor. For evaluation by testing or by experience data, conservatism has been introduced through the use of an increase scale factor which is applied to the prescribed design/evaluation input motion

  2. Evaluation of design flood estimates with respect to sample size

    Science.gov (United States)

    Kobierska, Florian; Engeland, Kolbjorn

    2016-04-01

    Estimation of design floods forms the basis for hazard management related to flood risk and is a legal obligation when building infrastructure such as dams, bridges and roads close to water bodies. Flood inundation maps used for land use planning are also produced based on design flood estimates. In Norway, the current guidelines for design flood estimates give recommendations on which data, probability distribution, and method to use dependent on length of the local record. If less than 30 years of local data is available, an index flood approach is recommended where the local observations are used for estimating the index flood and regional data are used for estimating the growth curve. For 30-50 years of data, a 2 parameter distribution is recommended, and for more than 50 years of data, a 3 parameter distribution should be used. Many countries have national guidelines for flood frequency estimation, and recommended distributions include the log Pearson II, generalized logistic and generalized extreme value distributions. For estimating distribution parameters, ordinary and linear moments, maximum likelihood and Bayesian methods are used. The aim of this study is to r-evaluate the guidelines for local flood frequency estimation. In particular, we wanted to answer the following questions: (i) Which distribution gives the best fit to the data? (ii) Which estimation method provides the best fit to the data? (iii) Does the answer to (i) and (ii) depend on local data availability? To answer these questions we set up a test bench for local flood frequency analysis using data based cross-validation methods. The criteria were based on indices describing stability and reliability of design flood estimates. Stability is used as a criterion since design flood estimates should not excessively depend on the data sample. The reliability indices describe to which degree design flood predictions can be trusted.

  3. Design evaluation of the HTGR fuel element size reduction system

    International Nuclear Information System (INIS)

    Strand, J.B.

    1978-06-01

    A fuel element size reduction system for the ''cold'' pilot plant of the General Atomic HTGR Reference Recycle Facility has been designed and tested. This report is both an evaluation of the design based on results of initial tests and a description of those designs which require completion or modification for hot cell use. 11 figures

  4. Evaluating design alternatives using conjoint experiments in virual reality

    NARCIS (Netherlands)

    Dijkstra, J.; Leeuwen, van J.P.; Timmermans, H.J.P.

    2003-01-01

    In this paper the authors describe the design of an experiment based on conjoint measurement that explores the possibility of using the Internet to evaluate design alternatives. These design alternatives are presented as panoramic views, and preferences are measured by asking subjects which

  5. Design of Softgauge for Surface Profile Evaluation

    International Nuclear Information System (INIS)

    Nie, M Q; Liu, X J; Jiang, X Q

    2006-01-01

    A concept of softgauge has been proposed by ISO in the context of surface texture measurement, in which reference software and reference data are included. In this paper, an effective scheme to build reference software for 2D surface profile measurement is proposed. The advantage of the scheme lies in its effective combination of high numerical calculating capability of MATLAB with perfect interface programming capability of VC. Preliminary reference software is developed, and typical algorithms are tested

  6. Evaluation of Mass Housing at the Pre-Design Stage

    Directory of Open Access Journals (Sweden)

    Kozan UZUNOĞLU

    2014-09-01

    Full Text Available Throughout history, housing has been a central problem in the lives of human beings. Housing, which includes shelter for family and functional volumes that meet social needs, used to be built specifically for the family. The concept of “Mass Housing” entered the field of architecture as a result of the industrial revolution, when lavish Renaissance housing gradually turned into housing for workers. Today, the demand for housing cannot keep up with fast-growing populations. Besides the quantitative problems of housing production, there is the ever- growing problem of quality, the solution to which lies with designer architects. On this issue of quality, Post Occupation Evaluation (POE studies, conducted to provide data for upcoming designs, and certificate evaluations like LEED and BREEAM, aimed at measuring energy performance effectiveness of new buildings, mostly involve measurements of usage of the building envelope, environmental relations, facilities and usage of natural resources. None prioritize the form and function issues of spatial usage in architectural designs. This study proposes a method that enables spatial and functional measurement and assessment at the project stage. The suggested spatial performance measurement–assessment system has three stages. In the first stage, the standards and usage criteria to be used as reference in the assessment are defined. The second stage suggests using the SAR analysis approach, and the third stage is about conducting “Spatial Performance Assessment”. Here, the common denominator of “User System” and “Building System”, which shares characteristic design criteria “Form, Function,Construction” is established and by this way, testing and assessing the subject of study becomes possible. With these assessments, by providing digitalization of spatial performance with proportional values, it is believed that a database for the provision of statistical information may be established.

  7. Line probe assay for differentiation within Mycobacterium tuberculosis complex. Evaluation on clinical specimens and isolates including Mycobacterium pinnipedii

    DEFF Research Database (Denmark)

    Kjeldsen, Marianne Kirstine; Bek, Dorte; Rasmussen, Erik Michael

    2009-01-01

    A line probe assay (GenoType MTBC) was evaluated for species differentiation within the Mycobacterium tuberculosis complex (MTBC). We included 387 MTBC isolates, 43 IS6110 low-copy MTBC isolates, 28 clinical specimens with varying microscopy grade, and 30 isolates of non-tuberculous mycobacteria...

  8. Training Software Developers and Designers to Conduct Usability Evaluations

    Science.gov (United States)

    Skov, Mikael Brasholt; Stage, Jan

    2012-01-01

    Many efforts to improve the interplay between usability evaluation and software development rely either on better methods for conducting usability evaluations or on better formats for presenting evaluation results in ways that are useful for software designers and developers. Both of these approaches depend on a complete division of work between…

  9. Design and Evaluation of Nextgen Aircraft Separation Assurance Concepts

    Science.gov (United States)

    Johnson, Walter; Ho, Nhut; Arutyunov, Vladimir; Laue, John-Luke; Wilmoth, Ian

    2012-01-01

    To support the development and evaluation of future function allocation concepts for separation assurance systems for the Next Generation Air Transportation System, this paper presents the design and human-in-the-loop evaluation of three feasible function allocation concepts that allocate primary aircraft separation assurance responsibilities and workload to: 1) pilots; 2) air traffic controllers (ATC); and 3) automation. The design of these concepts also included rules of the road, separation assurance burdens for aircraft of different equipage levels, and utilization of advanced weather displays paired with advanced conflict detection and resolution automation. Results of the human-in-the-loop simulation show that: a) all the concepts are robust with respect to weather perturbation; b) concept 1 (pilots) had highest throughput, closest to assigned spacing, and fewest violations of speed and altitude restrictions; c) the energy of the aircraft during the descent phase was better managed in concepts 1 and 2 (pilots and ATC) than in concept 3 (automation), in which the situation awareness of pilots and controllers was lowest, and workload of pilots was highest. The paper also discusses further development of these concepts and their augmentation and integration with future air traffic management tools and systems that are being considered for NextGen.

  10. Post design evaluation (ageing mechanisms, effects, management, monitoring, PSR, ISI)

    International Nuclear Information System (INIS)

    Ichikawa, Toshio

    2001-01-01

    Although the nuclear plant was designed for the purpose of the 30-year life the early stages of construction, it also already has the plant abolished by passing in 30 years. There is a plant under operation and a plant that is employed variously, extends the original life and continues operation now, and the plant that is going to be abolished politically is before a life. By using a nuclear plant for a long period of time, damage. by the influence of irradiation, wear of slipping, corrosion, etc. appears. When this degradation is left, the serious accident is caused. In this lecture, refer to Assessment and management of ageing of major nuclear power plant components important to safety, Oct. 1999 of IAEA. A point of view from guide is introduced about management of the mechanism in the secular degradation mode expected by operating for a long period of time, the influence of secular degradation, and influence, monitoring technology, periodical safe evaluation, and a periodic inspection. And raises and explains the correspondence situation of secular degradation, and the example of evaluation of PSR and ISI equipment. The aging mechanism for reactor vessel internal components considered are related to embrittlement, fatigue, corrosion, radiation induced creep, relaxation and swelling, and mechanical wear. This lecture includes; monitoring methods, a description of periodic safety reviews and a sample of seismic design periodic safety report for the reactor internals

  11. Designing the Cash and Counseling Demonstration and Evaluation.

    Science.gov (United States)

    Doty, Pamela; Mahoney, Kevin J; Simon-Rusinowitz, Lori

    2007-02-01

    The Cash and Counseling Demonstration and Evaluation (CCDE) was designed as an experiment in shifting the paradigm in home and community-based long-term care from a professional/bureaucratic model of service delivery to one emphasizing consumer choice and control. The experimental intervention was an individualized budget offered in lieu of traditional Medicaid-covered services, such as agency-delivered aide services or a plan of care developed and coordinated by a professional case-manager, which typically involves authorization for several different providers to deliver a range of services. Within the spending limits established by their budgets, program participants were largely free to choose the types and amounts of paid services and supports they judged best able to meet their disability-related personal assistance needs. Medicaid beneficiaries in selected states who volunteered to participate. In all of the participating state Medicaid programs, beneficiaries eligible to participate included elders and younger adults with chronic disabilities and, in one state, adults and children with mental retardation/developmental disabilities could also participate. Minor children and adults with cognitive impairment could participate via representatives (family or friends who agreed to assist them in managing their services or to act as their surrogate decision-makers). Members of the CCDE management team describe the rationale for and implications of key design decisions. Key design decisions included the choice of research methodology (random assignment of CCDE participants in each state to treatment and control groups), selection of the state sites (AR, FL, NJ, NY), and the need for the CCDE to comply with federal waiver requirements for Medicaid research and demonstration projects. Principle Findings. The CCDE design was successfully implemented in three of the four state Medicaid programs selected for participation. The successful implementation of the CCDE

  12. Grouping of the design issues for KNGR MMI evaluation

    International Nuclear Information System (INIS)

    Oh, In Seok; Lee, Dong Young; Lee, Jung Woon; Lee, Hyn Chul; Park, Jae Chang

    2001-05-01

    The Korean Next Generation Reactor(KNGR) man-machine interface(MMI) design adopting digital technologies has been developed since 1997. The KNGR MMI consists of CRT-based operator workstations, large display panel(LDP), alarm System, soft control and computerized procedure system. Westinghouse tried to systematically identify and evaluate human factor potential issues of advanced control room. The KNGR MMI design features are very similar with those of the Westinghouse AP-600. The KNGR will try to reflect the evaluation results of 15 issues that the Westinghouse has developed. But it needs much time and costs to evaluate the 15 issues during this design phase. In this study, we analyzed evaluation issues of the AP-600 and classified the 13 issues, which the Westinghouse developed, into 5 groups to simultaneously except 2 issues which can not evaluate in this design phase

  13. Multinational design evaluation programme. Annual Report April 2015-April 2016

    International Nuclear Information System (INIS)

    2016-05-01

    The Multinational Design Evaluation Programme (MDEP) is a multinational initiative to leverage the resources and knowledge of national regulatory authorities that are, or will shortly be, undertaking the review of new reactor power plant designs. MDEP incorporates a broad range of activities including enhancing multilateral co-operation within existing regulatory frameworks, and increasing multinational convergence of codes, standards, guides, and safety goals. A key concept throughout the work of MDEP is that national regulators retain sovereign authority for all licensing and regulatory decisions. Working groups are implementing the activities in accordance with programme plans with specific activities and goals, and have established the necessary interfaces both within and outside of MDEP. This report provides a status of the programme after its eighth year of implementation. Content: Executive Summary; 1 - Introduction; 2 - Programme goals and outcomes; 3 - Programme implementation (Membership, Organizational structure, MDEP Library, Common positions); 4 - Interactions with other organizations; 5 - Current activities (EPR Working Group (EPRWG), AP1000 Working Group (AP1000WG), APR1400 Design-specific Working Group (APR1400WG), VVER Working Group (VVERWG), ABWR Working Group (ABWRWG), Vendor Inspection Co-operation Working Group (VICWG), Codes and Standards Working Group (CSWG), Digital Instrumentation and Controls Working Group (DICWG); 6 - Interim results; 7 - Next steps - future of the programme; appendix 1: List of abbreviations and acronyms; Appendix 2: Revised documents and publications; Appendix 3: Photographs of reactors considered within MDEP

  14. Oil-points - Designers means to evaluate sustainability of concepts

    DEFF Research Database (Denmark)

    Bey, Niki; Lenau, Torben Anker

    1998-01-01

    Designers have an essential influence on product design and are therefore one target group for environmental evaluation methods. This implies, that such evaluation methods have to meet designers requirements. Evaluation of sustainability of products is often done using formal Life Cycle Assessment....... This is investigated by means of three case studies where environmental impact is estimated using the EDIP method, the Eco-indicator 95 method, and the Oil Point method proposed by the authors. It is found that the results obtained using Oil Points are in acceptable conformity with the results obtained with more...

  15. Multinational design evaluation programme - Annual report March 2013-March 2014

    International Nuclear Information System (INIS)

    2014-04-01

    The Multinational Design Evaluation Programme (MDEP) is a multinational initiative to leverage the resources and knowledge of national regulatory authorities who are, or will shortly be, undertaking the review of new reactor power plant designs. MDEP incorporates a broad range of activities including enhancing multilateral cooperation within existing regulatory frameworks, and increasing multinational convergence of codes, standards, guides, and safety goals. A key concept throughout the work of MDEP is that national regulators retain sovereign authority for all licensing and regulatory decisions. Working groups are implementing the activities in accordance with programme plans with specific activities and goals, and have established the necessary interfaces both within and outside of the MDEP members. In the past year, MDEP has expanded to include cooperation on the VVER and ABWR designs and additional members have begun participating in the programme to share their experiences on these design reviews. This report provides the current status of the programme. Significant progress is being made on the overall MDEP goals of increased cooperation and enhanced convergence of requirements and practices. In addition, the lessons learnt from the 11 March 2011, events at the Fukushima Daiichi nuclear power plant are being incorporated into MDEP activities through the programme plans of design-specific working groups (DSWG). On this topic, the EPR Working Group has issued a common position which will be supplemented by five technical appendices by the end of 2014. Other DSWG are in the process of drafting such common positions. Several DSWGs' are facilitating the MDEP programme goal of enhanced cooperation: the EPRWG, the Vendor Inspection Cooperation Working Group (VICWG), the Digital Instrumentation and Controls Working Group (DICWG), the Codes and Standards Working Group (CSWG). Accomplishments to date provide confidence that the MDEP membership, structure and processes

  16. Evaluating hospital design from an operations management perspective.

    Science.gov (United States)

    Vos, Leti; Groothuis, Siebren; van Merode, Godefridus G

    2007-12-01

    This paper describes an evaluation method for the assessment of hospital building design from the viewpoint of operations management to assure that the building design supports the efficient and effective operating of care processes now and in the future. The different steps of the method are illustrated by a case study. In the case study an experimental design is applied to assess the effect of used logistical concepts, patient mix and technologies. The study shows that the evaluation method provides a valuable tool for the assessment of both functionality and the ability to meet future developments in operational control of a building design.

  17. 40 CFR 63.2354 - What performance tests, design evaluations, and performance evaluations must I conduct?

    Science.gov (United States)

    2010-07-01

    ... evaluations, and performance evaluations must I conduct? 63.2354 Section 63.2354 Protection of Environment... tests, design evaluations, and performance evaluations must I conduct? (a)(1) For each performance test... procedures specified in subpart SS of this part. (3) For each performance evaluation of a continuous emission...

  18. COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

    NARCIS (Netherlands)

    DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

    1993-01-01

    The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

  19. COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .2. DESIGN EVALUATION ON MEASURED DATA

    NARCIS (Netherlands)

    DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

    The construction of a small experimental design for a combination of process and mixture variables is a problem which has not been solved completely by now. In a previous paper we evaluated some designs with theoretical measures. This second paper evaluates the capabilities of the best of these

  20. INTERNATIONAL LOGISTICS SYSTEMS DESIGN AND EFFECTIVENESS EVALUATION

    Directory of Open Access Journals (Sweden)

    N. V. Khalipova

    2015-08-01

    Full Text Available Purpose. In the paper the question of the development of a methodological approach to the determination of logistics systems’ performance and grounding of the most effective goods’ delivery schemes, based on the theory of functions and sets of multiple objects, vector optimization approaches and discrete maximum principle for multi-stage processes (phase method is considered. Methodology. To achieve the goals of the research, the model of logistic system represented by multiple object that defined by the structure and content. The object is represented by hybrid superposition, composed of sets, multi-sets, ordered sets (lists and inhomogeneous sets (sequences, corteges, which at each stage of cargo delivery present sets of technological operations of their processing, choices and decisions algorithms. Multiple structure of objects is constructive three, consisting of the carrier, signatures and axiomatic. To determine the effective scheme of delivery, applied discrete maximum principle using vector optimization criterion. Findings. In this article, logistics system of delivery is presented in the form of a multi-stage (phase of the process. Each stage reviews a plurality of discrete activities sets, which includes the possible technology cycles of operations in goods handling. At each stage of a multi-phase delivery process from the supplier to the consumer, these sets are different. Considered a model example solving the problem of vector optimization options for delivery of goods by the road in the international logistics system for the five-step process. Optimization performed on the basis of three indicators. Originality. In this paper, the choice of the most effective way of delivery goods produced using the theory of functions and sets of multiple objects, using the discrete maximum principle for multi-stage processes, based on the vector optimization criterion. At each of its stages are formed a plurality of valid solutions as

  1. Improved field experimental designs and quantitative evaluation of aquatic ecosystems

    Energy Technology Data Exchange (ETDEWEB)

    McKenzie, D.H.; Thomas, J.M.

    1984-05-01

    The paired-station concept and a log transformed analysis of variance were used as methods to evaluate zooplankton density data collected during five years at an electrical generation station on Lake Michigan. To discuss the example and the field design necessary for a valid statistical analysis, considerable background is provided on the questions of selecting (1) sampling station pairs, (2) experimentwise error rates for multi-species analyses, (3) levels of Type I and II error rates, (4) procedures for conducting the field monitoring program, and (5) a discussion of the consequences of violating statistical assumptions. Details for estimating sample sizes necessary to detect changes of a specified magnitude are included. Both statistical and biological problems with monitoring programs (as now conducted) are addressed; serial correlation of successive observations in the time series obtained was identified as one principal statistical difficulty. The procedure reduces this problem to a level where statistical methods can be used confidently. 27 references, 4 figures, 2 tables.

  2. Using Models of Cognition in HRI Evaluation and Design

    National Research Council Canada - National Science Library

    Goodrich, Michael A

    2004-01-01

    ...) guide the construction of experiments. In this paper, we present an information processing model of cognition that we have used extensively in designing and evaluating interfaces and autonomy modes...

  3. Modular reconfigurable machine tools: design, control and evaluation

    CSIR Research Space (South Africa)

    Padayachee, J

    2009-11-01

    Full Text Available The reconfigurable manufacturing system (RMS) paradigm encapsulates methodologies that enable manufacturing systems to cope effectively with market and product changes. This research presents the design and evaluation of modular reconfigurable...

  4. Shielding Design and Radiation Shielding Evaluation for LSDS System Facility

    International Nuclear Information System (INIS)

    Kim, Younggook; Kim, Jeongdong; Lee, Yongdeok

    2015-01-01

    As the system characteristics, the target in the spectrometer emits approximately 1012 neutrons/s. To efficiently shield the neutron, the shielding door designs are proposed for the LSDS system through a comparison of the direct shield and maze designs. Hence, to guarantee the radiation safety for the facility, the door design is a compulsory course of the development of the LSDS system. To improve the shielding rates, 250x250 covering structure was added as a subsidiary around the spectrometer. In this study, the evaluations of the suggested shielding designs were conducted using MCNP code. The suggested door design and covering structures can shield the neutron efficiently, thus all evaluations of all conditions are satisfied within the public dose limits. From the Monte Carlo code simulation, Resin(Indoor type) and Tungsten(Outdoor type) were selected as the shielding door materials. From a comparative evaluation of the door thickness, In and Out door thickness was selected 50 cm

  5. Designing and evaluating sociability in online video games

    OpenAIRE

    Christou, Georgios; Law, Effie; Geerts, David; Nacke, Lennart; Zaphiris, Panayiotis

    2013-01-01

    The emergence of Online Video Games has led to new ways of socializing with friends. Nowadays a good online game is also associated with the pleasure of socializing and interaction with other players. One cannot play such a game solitarily in a meaningful sense without interacting with the other players. However, there are still no integrated ways of designing and evaluating the inherent sociability of online video games, nor are there methods or guidelines for designing and evaluating social...

  6. Evaluation of Information Requirements of Reliability Methods in Engineering Design

    DEFF Research Database (Denmark)

    Marini, Vinicius Kaster; Restrepo-Giraldo, John Dairo; Ahmed-Kristensen, Saeema

    2010-01-01

    This paper aims to characterize the information needed to perform methods for robustness and reliability, and verify their applicability to early design stages. Several methods were evaluated on their support to synthesis in engineering design. Of those methods, FMEA, FTA and HAZOP were selected...

  7. Peer assessment in university teaching: Evaluating seven course designs

    NARCIS (Netherlands)

    van den Berg, I.|info:eu-repo/dai/nl/288125797; Admiraal, W.|info:eu-repo/dai/nl/120226340; Pilot, A.|info:eu-repo/dai/nl/068350880

    2006-01-01

    Peer assessment in university teaching: evaluating seven course designs Abstract Peer assessment is understood to be an arrangement with students assessing the quality of their fellow students’ writings and giving feedback to each other. This multiple-case study of seven designs of peer assessment

  8. Improvement in genetic evaluation of female fertility in dairy cattle using multiple-trait models including milk production traits

    DEFF Research Database (Denmark)

    Sun, C; Madsen, P; Lund, M S

    2010-01-01

    This study investigated the improvement in genetic evaluation of fertility traits by using production traits as secondary traits (MILK = 305-d milk yield, FAT = 305-d fat yield, and PROT = 305-d protein yield). Data including 471,742 records from first lactations of Denmark Holstein cows, covering...... the years of inseminations during first lactations from 1995 to 2004, were analyzed. Six fertility traits (i.e., interval in days from calving to first insemination, calving interval, days open, interval in days from first to last insemination, numbers of inseminations per conception, and nonreturn rate...... stability and predictive ability than single-trait models for all the fertility traits, except for nonreturn rate within 56 d after first service. The stability and predictive ability for the model including MILK or PROT were similar to the model including all 3 milk production traits and better than...

  9. Evaluation of Embedded System Component Utilized in Delivery Integrated Design Project Course

    Science.gov (United States)

    Junid, Syed Abdul Mutalib Al; Hussaini, Yusnira; Nazmie Osman, Fairul; Razak, Abdul Hadi Abdul; Idros, Mohd Faizul Md; Karimi Halim, Abdul

    2018-03-01

    This paper reports the evaluation of the embedded system component utilized in delivering the integrated electronic engineering design project course. The evaluation is conducted based on the report project submitted as to fulfil the assessment criteria for the integrated electronic engineering design project course named; engineering system design. Six projects were assessed in this evaluation. The evaluation covers the type of controller, programming language and the number of embedded component utilization as well. From the evaluation, the C-programming based language is the best solution preferred by the students which provide them flexibility in the programming. Moreover, the Analog to Digital converter is intensively used in the projects which include sensors in their proposed design. As a conclusion, in delivering the integrated design project course, the knowledge over the embedded system solution is very important since the high density of the knowledge acquired in accomplishing the project assigned.

  10. Design Alternative Evaluation No. 3: Post-Closure Ventilation

    International Nuclear Information System (INIS)

    Logan, R.C.

    1999-01-01

    The objective of this study is to provide input to the Enhanced Design Alternatives (EDA) for License Application Design Selection (LADS). Its purpose is to develop and evaluate conceptual designs for post-closure ventilation alternatives that enhance repository performance. Post-closure ventilation is expected to enhance repository performance by limiting the amount of water contacting the waste packages. Limiting the amount of water contacting the waste packages will reduce corrosion

  11. The Design and Evaluation of Teaching Experiments in Computer Science.

    Science.gov (United States)

    Forcheri, Paola; Molfino, Maria Teresa

    1992-01-01

    Describes a relational model that was developed to provide a framework for the design and evaluation of teaching experiments for the introduction of computer science in secondary schools in Italy. Teacher training is discussed, instructional materials are considered, and use of the model for the evaluation process is described. (eight references)…

  12. Evaluating Online Dialogue on "Security" Using a Novel Instructional Design

    Science.gov (United States)

    Arora, Payal

    2008-01-01

    This paper explores evaluation strategies to gauge the impact of a novel instructional design on international community participation online. This is done by conceptualizing and devising indicators for measuring "engagement" online amongst marginalized adult communities worldwide. In doing so, a review of online evaluation literature is…

  13. Evaluation of the 235U prompt fission neutron spectrum including a detailed analysis of experimental data and improved model information

    Science.gov (United States)

    Neudecker, Denise; Talou, Patrick; Kahler, Albert C.; White, Morgan C.; Kawano, Toshihiko

    2017-09-01

    We present an evaluation of the 235U prompt fission neutron spectrum (PFNS) induced by thermal to 20-MeV neutrons. Experimental data and associated covariances were analyzed in detail. The incident energy dependence of the PFNS was modeled with an extended Los Alamos model combined with the Hauser-Feshbach and the exciton models. These models describe prompt fission, pre-fission compound nucleus and pre-equilibrium neutron emissions. The evaluated PFNS agree well with the experimental data included in this evaluation, preliminary data of the LANL and LLNL Chi-Nu measurement and recent evaluations by Capote et al. and Rising et al. However, they are softer than the ENDF/B-VII.1 (VII.1) and JENDL-4.0 PFNS for incident neutron energies up to 2 MeV. Simulated effective multiplication factors keff of the Godiva and Flattop-25 critical assemblies are further from the measured keff if the current data are used within VII.1 compared to using only VII.1 data. However, if this work is used with ENDF/B-VIII.0β2 data, simulated values of keff agree well with the measured ones.

  14. Multinational Design Evaluation Programme. Annual Report - April 2014-April 2015

    International Nuclear Information System (INIS)

    2015-06-01

    The Multinational Design Evaluation Programme (MDEP) is a multinational initiative to leverage the resources and knowledge of national regulatory authorities who are, or will shortly be, undertaking the review of new reactor power plant designs. MDEP incorporates a broad range of activities including enhancing multilateral co-operation within existing regulatory frameworks, and increasing multinational convergence of codes, standards, guides and safety goals. A key concept throughout the work of MDEP is that national regulators retain sovereign authority for all licensing and regulatory decisions. Working groups are implementing the activities in accordance with programme plans with specific activities and goals, and have established the necessary interfaces both within and outside of MDEP. This report provides a status of the programme after its seventh year of implementation. Content: Executive summary; 1. Introduction; 2. Programme goals and outcomes; 3. Programme implementation (Membership, Organisational structure, MDEP Library, Common positions); 4. Interactions with other organisations; 5. Current activities (EPR Working Group (EPRWG), AP1000 Working Group (AP1000WG), APR1400 Working Group (APR1400WG), VVER Working Group (VVERWG), AVBWR Working Group (ABWRWG), Vendor Inspection Co-operation Working Group (VICWG), Codes and Standards Working Group (CSWG), Digital Instrumentation and Controls Working Group (DICWG)); 6. Interim results; 7. Next steps - Future of the programme; Appendix 1 - List of abbreviations and acronyms; Appendix 2 - Revised documents and publications; Appendix 3 - Photographs of reactors considered within MDEP

  15. Evaluation and study of advanced optical contamination, deposition, measurement, and removal techniques. [including computer programs and ultraviolet reflection analysis

    Science.gov (United States)

    Linford, R. M. F.; Allen, T. H.; Dillow, C. F.

    1975-01-01

    A program is described to design, fabricate and install an experimental work chamber assembly (WCA) to provide a wide range of experimental capability. The WCA incorporates several techniques for studying the kinetics of contaminant films and their effect on optical surfaces. It incorporates the capability for depositing both optical and contaminant films on temperature-controlled samples, and for in-situ measurements of the vacuum ultraviolet reflectance. Ellipsometer optics are mounted on the chamber for film thickness determinations, and other features include access ports for radiation sources and instrumentation. Several supporting studies were conducted to define specific chamber requirements, to determine the sensitivity of the measurement techniques to be incorporated in the chamber, and to establish procedures for handling samples prior to their installation in the chamber. A bibliography and literature survey of contamination-related articles is included.

  16. Evaluation of three coding schemes designed for improved data communication

    Science.gov (United States)

    Snelsire, R. W.

    1974-01-01

    Three coding schemes designed for improved data communication are evaluated. Four block codes are evaluated relative to a quality function, which is a function of both the amount of data rejected and the error rate. The Viterbi maximum likelihood decoding algorithm as a decoding procedure is reviewed. This evaluation is obtained by simulating the system on a digital computer. Short constraint length rate 1/2 quick-look codes are studied, and their performance is compared to general nonsystematic codes.

  17. Expert systems for space power supply: design, analysis, and evaluation

    International Nuclear Information System (INIS)

    Cooper, R.S.; Thomson, M.K.; Hoshor, A.

    1987-01-01

    The authors evaluated the feasibility of applying expert systems to the conceptual design, analysis, and evaluation of space power supplies in particular, and complex systems in general. To do this, they analyzed the space power supply design process and in associated knowledge base, and characterized them in a form suitable for computer emulation of a human expert. The existing expert system tools and the results achieved with them were evaluated to assess their applicability to power system design. They applied some new concepts for combining program architectures (modular expert systems and algorithms) with information about the domain to create a deep system for handling the complex design problem. They authors developed, programmed and tested NOVICE, a code to solve a simplified version of a scoping study of a wide variety of power supply types for a broad range of missions, as a concrete feasibility demonstration

  18. Expert System Approach For Generating And Evaluating Engine Design Alternatives

    Science.gov (United States)

    Shen, Stewart N. T.; Chew, Meng-Sang; Issa, Ghassan F.

    1989-03-01

    Artificial intelligence is becoming an increasingly important subject of study for computer scientists, engineering designers, as well as professionals in other fields. Even though AI technology is a relatively new discipline, many of its concepts have already found practical applications. Expert systems, in particular, have made significant contributions to technologies in such fields as business, medicine, engineering design, chemistry, and particle physics. This paper describes an expert system developed to aid the mechanical designer with the preliminary design of variable-stroke internal-combustion engines. The expert system accomplished its task by generating and evaluating a large number of design alternatives represented in the form of graphs. Through the application of structural and design rules directly to the graphs, optimal and near optimal preliminary design configurations of engines are deduced.

  19. Designing Preclinical Instruction of Psychomotor Skills (IV)--Instructional Engineering: Evaluation Phase.

    Science.gov (United States)

    Guenzel, Pamela J.; And Others

    1995-01-01

    The fourth article in a four-part series on instructional design discusses evaluation of a psychomotor skills unit taught in preclinical dental education. Issues examined include piloting of instructional materials, analysis and revision of materials based on student performance, syllabus design and content, influence of faculty characteristics,…

  20. 75 FR 38129 - Freescale Semiconductor, Inc., Hardware/Software Design and Manufacturing A Including On-Site...

    Science.gov (United States)

    2010-07-01

    ... Manufacturing A, Austin, Texas. The notice was published in the Federal Register on May 28, 2010 (75 FR 30070...Logic, Inc., Austin, TX; Amended Certification Regarding Eligibility To Apply for Worker Adjustment..., Design Solutions, Inc., Veriseo, SilconElite and MicroLogic, Inc. were employed on-site at the Austin...

  1. Design and Evaluation of a Secure Virtual Power Plant.

    Energy Technology Data Exchange (ETDEWEB)

    Johnson, Jay Tillay [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2017-09-01

    For three years, Sandia National Laboratories, Georgia Institute of Technology, and University of Illinois at Urbana-Champaign investigated a smart grid vision in which renewable-centric Virtual Power Plants (VPPs) provided ancillary services with interoperable distributed energy resources (DER). This team researched, designed, built, and evaluated real-time VPP designs incorporating DER forecasting, stochastic optimization, controls, and cyber security to construct a system capable of delivering reliable ancillary services, which have been traditionally provided by large power plants or other dedicated equipment. VPPs have become possible through an evolving landscape of state and national interconnection standards, which now require DER to include grid-support functionality and communications capabilities. This makes it possible for third party aggregators to provide a range of critical grid services such as voltage regulation, frequency regulation, and contingency reserves to grid operators. This paradigm (a) enables renewable energy, demand response, and energy storage to participate in grid operations and provide grid services, (b) improves grid reliability by providing additional operating reserves for utilities, independent system operators (ISOs), and regional transmission organization (RTOs), and (c) removes renewable energy high-penetration barriers by providing services with photovoltaics and wind resources that traditionally were the jobs of thermal generators. Therefore, it is believed VPP deployment will have far-reaching positive consequences for grid operations and may provide a robust pathway to high penetrations of renewables on US power systems. In this report, we design VPPs to provide a range of grid-support services and demonstrate one VPP which simultaneously provides bulk-system energy and ancillary reserves.

  2. Design and evaluation of cellular power converter architectures

    Science.gov (United States)

    Perreault, David John

    Power electronic technology plays an important role in many energy conversion and storage applications, including machine drives, power supplies, frequency changers and UPS systems. Increases in performance and reductions in cost have been achieved through the development of higher performance power semiconductor devices and integrated control devices with increased functionality. Manufacturing techniques, however, have changed little. High power is typically achieved by paralleling multiple die in a sing!e package, producing the physical equivalent of a single large device. Consequently, both the device package and the converter in which the device is used continue to require large, complex mechanical structures, and relatively sophisticated heat transfer systems. An alternative to this approach is the use of a cellular power converter architecture, which is based upon the parallel connection of a large number of quasi-autonomous converters, called cells, each of which is designed for a fraction of the system rating. The cell rating is chosen such that single-die devices in inexpensive packages can be used, and the cell fabricated with an automated assembly process. The use of quasi-autonomous cells means that system performance is not compromised by the failure of a cell. This thesis explores the design of cellular converter architectures with the objective of achieving improvements in performance, reliability, and cost over conventional converter designs. New approaches are developed and experimentally verified for highly distributed control of cellular converters, including methods for ripple cancellation and current-sharing control. The performance of these techniques are quantified, and their dynamics are analyzed. Cell topologies suitable to the cellular architecture are investigated, and their use for systems in the 5-500 kVA range is explored. The design, construction, and experimental evaluation of a 6 kW cellular switched-mode rectifier is also addressed

  3. THE LEGITIMACY OF INCLUDING THE SOCIAL PARAMETERS IN EVALUATING THE HEALTH STATUS IN THE SOCIAL ASSURANCE SYSTEM

    Directory of Open Access Journals (Sweden)

    MIHAI NEDELCU

    2011-04-01

    Full Text Available The social state crisis encouraged a reductionist tendency which had recently developed in the evaluations of the health status in the social assurance system. A holistic, psycho-medical approach, which took in consideration the implications of the social factors regarding disability, was confronted with a strictly medical model, in which the illness is exclusively considered a person’s problem; therefore, the references towards the „social” are irrelevant. In this context, the present paper states the question of the legitimacy of using some sociological concepts, in medical expertise, considered relevant in this area, such as: „occupational access” or the „social functioning of the person”. The present study doesn’t stop at offering as arguments of legitimacy the authority of some recommendations regarding the use of the social-medical model, including the evaluation of the health status, recommendations received from the behalf of OMS and the European Council (see CIF. The paper presents the construction of specific evaluation instruments and tries to identify the sense in which using the references regarding the „social” could influence the pressures in the social assurance system.

  4. A study on the quantitative evaluation for the software included in digital systems of nuclear power plants

    Energy Technology Data Exchange (ETDEWEB)

    Park, J. K.; Sung, T. Y.; Eom, H. S.; Jeong, H. S.; Kang, H. G.; Lee, K. Y.; Park, J. K. [Korea Atomic Energy Research Institute, Taejeon (Korea)

    2002-03-01

    In general, probabilistic safety analysis (PSA) has been used as one of the most important methods to evaluate the safety of NPPs. The PSA, because most of NPPs have been installed and used analog I and C systems, has been performed based on the hardware perspectives. In addition, since the tendency to use digital I and C systems including software instead of analog I and C systems is increasing, the needs of quantitative evaluation methods so as to perform PSA are also increasing. Nevertheless, several reasons such as software did not aged and it is very perplexed to estimate software failure rate due to its non-linearity, make the performance of PSA difficult. In this study, in order to perform PSA including software more efficiently, test-based software reliability estimation methods are reviewed to suggest a preliminary procedure that can provide reasonable guidances to quantify software failure rate. In addition, requisite activities to enhance applicability of the suggested procedure are also discussed. 67 refs., 11 figs., 5 tabs. (Author)

  5. Design and evaluation of physical protection systems of nuclear facilities

    Energy Technology Data Exchange (ETDEWEB)

    An, Jin Soo; Lee, Hyun Chul; Hwang, In Koo; Kwack, Eun Ho; Choi, Yung Myung

    2001-06-01

    Nuclear material and safety equipment of nuclear facilities are required to be protected against any kind of theft or sabotage. Physical protection is one of the measures to prevent such illegally potential threats for public security. It should cover all the cases of use, storage, and transportation of nuclear material. A physical protection system of a facility consists of exterior intrusion sensors, interior intrusion sensors, an alarm assessment and communication system, entry control systems, access delay equipment, etc. The design of an effective physical protection system requires a comprehensive approach in which the designers define the objective of the system, establish an initial design, and evaluate the proposed design. The evaluation results are used to determine whether or not the initial design should be modified and improved. Some modelling techniques are commonly used to analyse and evaluate the performance of a physical protection system. Korea Atomic Energy Research Institute(KAERI) has developed a prototype of software as a part of a full computer model for effectiveness evaluation for physical protection systems. The input data elements for the prototype, contain the type of adversary, tactics, protection equipment, and the attributes of each protection component. This report contains the functional and structural requirements defined in the development of the evaluation computer model.

  6. 47 CFR 7.7 - Product design, development, and evaluation.

    Science.gov (United States)

    2010-10-01

    ...: (1) Where market research is undertaken, including individuals with disabilities in target populations of such research; (2) Where product design, testing, pilot demonstrations, and product trials are... access solutions through testing with individuals with disabilities or with appropriate disability...

  7. Ergonomic design and evaluation of new surgical scissors.

    Science.gov (United States)

    Shimomura, Yoshihiro; Shirakawa, Hironori; Sekine, Masashi; Katsuura, Tetsuo; Igarashi, Tatsuo

    2015-01-01

    The purpose of this study is to design a new surgical scissors handle and determine its effectiveness with various usability indices. A new scissors handle was designed that retains the professional grip but has the shapes of the eye rings modified to fit the thumb and ring finger and finger rests for the index and little finger. The newly designed scissors and traditional scissors were compared by electromyography, subjective evaluation and task performance in experiments using cutting and peeling tasks. The newly designed scissors reduced muscle load in both hand during cutting by the closing action, and reduced the muscle load in the left hand during peeling by the opening action through active use of the right hand. In evaluation by surgeons, task performance improved in addition to the decrease in muscle load. The newly designed scissors used in this study demonstrated high usability. A new scissors handle was designed that has the eye rings modified to fit the thumb and ring finger. The newly designed scissors reduced muscle load and enabled active use of the right hand. In evaluation by surgeons, task performance improved in addition to the decrease in muscle load.

  8. Evaluating cartographic design principles applied to space-time cube content

    DEFF Research Database (Denmark)

    Kveladze, Irma; Kraak, Menno-Jan

    2013-01-01

    the different uses of the graphic variables and depth cues to represent the paths and stations. Both quantitative and qualitative evaluation methods were applied during the testing. The results gave an indication on how design influence the 'performance' of the STC, and resulted in guidelines for the design...... to the neglectance of a proper cartographic design. To judge the influence of this design on the effectiveness and efficiency of the STC as a graphic representation of movement data a user-centered design evaluation has been set up. The experiment included two applications each with its own characteristic data...... complexity and content. It involved a historic and an urban problem case. The first is a relatively simple dataset of historical movements and the second is a complex dataset of pedestrians movement. Based on questions formulated by domain experts different design scenarios were tested. These included...

  9. Evaluating a proposed apprach for managing collaborative design in the conceptual design phase

    NARCIS (Netherlands)

    Sebastian, R.

    2006-01-01

    This paper evaluates the findings of prior research on managing collaborative design in the conceptual design phase of a building project. The prior research was explorative. It used several building projects in the Netherlands as case studies - De Resident in The Hague, Nieuw Stadshart in Almere,

  10. Design and evaluation of an integrated safeguards system: principles

    International Nuclear Information System (INIS)

    Markin, J.T.; Coulter, C.A.; Gutmacher, R.G.; Whitty, W.J.

    1984-07-01

    An integrated safeguards system is defined as a collection of safeguards activities in which system components are coordinated to meet safeguards objectives efficiently within constraints imposed by safeguards resources, facility operations, potential adversaries, and regulatory requirements. This paper describes principles for designing and evaluating an integrated safeguards system that consists of four parts: (1) a problem definition phase that specifies resources and constraints composing the problem boundary values; (2) a system analysis/synthesis phase that describes how to select and integrate safeguards activities for efficient attainment of system objectives; (3) a system evaluation/optimization phase that defines measures of safeguards performance and develops methods for evaluating them; and (4) a decision-making phase that develops principles for selecting admissible designs and preference-ordering designs. 6 references, 4 figures, 5 tables

  11. Design and evaluation of an integrated safeguards system: principles

    International Nuclear Information System (INIS)

    Markin, J.T.; Coulter, C.A.; Gutmacher, R.G.; Whitty, W.J.

    1984-01-01

    An integrated safeguards system is defined as a collection of safeguards activities in which system components are coordinated to meet safeguards objectives efficiently within constraints imposed by safeguards resources, facility operations, potential adversaries, and regulatory requirements. This paper describes principles for designing and evaluating an integrated safeguards system that consists of four parts: a problem definition phase that specifies resources and constraints composing the problem boundary values, a system analysis/synthesis phase that describes how to select and integrate safeguards activities for efficient attainment of system objectives, a system evaluation/optimization phase that defines measures of safeguards performance and develops methods for evaluating them, and a decision-making phase that develops principles for selecting admissible designs and preference-ordering designs

  12. PGSFR Core Thermal Design Procedure to Evaluate the Safety Margin

    Energy Technology Data Exchange (ETDEWEB)

    Choi, Sun Rock; Kim, Sang-Ji [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

    2014-10-15

    The Korea Atomic Energy Research Institute (KAERI) has performed a SFR design with the final goal of constructing a prototype plant by 2028. The main objective of the SFR prototype plant is to verify the TRU metal fuel performance, reactor operation, and transmutation ability of high-level wastes. The core thermal design is to ensure the safe fuel performance during the whole plant operation. Compared to the critical heat flux in typical light water reactors, nuclear fuel damage in SFR subassemblies arises from a creep induced failure. The creep limit is evaluated based on the maximum cladding temperature, power, neutron flux, and uncertainties in the design parameters, as shown in Fig. 1. In this work, the core thermal design procedures are compared to verify the present PGSFR methodology based on the nuclear plant design criteria/guidelines and previous SFR thermal design methods. The PGSFR core thermal design procedure is verified based on the nuclear plant design criteria/guidelines and previous methods in LWRs and SFRs. The present method aims to directly evaluate the fuel cladding failure and to assure more safety margin. The 2 uncertainty is similar to 95% one-side tolerance limit of 1.96 in LWRs. The HCFs, ITDP, and MCM reveal similar uncertainty propagation for cladding midwall temperature for typical SFR conditions. The present HCFs are mainly employed from the CRBR except the fuel-related uncertainty such as an incorrect fuel distribution. Preliminary PGSFR specific HCFs will be developed by the end of 2015.

  13. Evaluation of RF properties by orifice design for IFMIF RFQ

    International Nuclear Information System (INIS)

    Maebara, Sunao; Sugimoto, Masayoshi

    2005-03-01

    Orifices for the IFMIF RFQ have been designed and fabricated, and RF properties have been evaluated by a network analyzer. The designed orifices were installed into a vacuum port of the 1.1m-long RFQ mock-up module, and the resonant frequency and the phase difference between cavities were measured for a quadrupole operation mode of TE 210 . It was found that the RF properties are not affected on condition that slit direction with the same direction of current flow at the RFQ wall. Orifice conductance from 0.22 to 0.25 m 3 /sec by nitrogen conversion at room temperature was designed, and an ultimate pressure level of 5x10 -7 [Pa] was evaluated for the 4.1m-long central module for the IFMIF RFQ. It was concluded that the designed orifices are effective for RF properties and vacuum conductance in the IFMIF RFQ. (author)

  14. A Standardized Rubric for Evaluating Webquest Design: Reliability Analysis of ZUNAL Webquest Design Rubric

    Science.gov (United States)

    Unal, Zafer; Bodur, Yasar; Unal, Aslihan

    2012-01-01

    Current literature provides many examples of rubrics that are used to evaluate the quality of web-quest designs. However, reliability of these rubrics has not yet been researched. This is the first study to fully characterize and assess the reliability of a webquest evaluation rubric. The ZUNAL rubric was created to utilize the strengths of the…

  15. Evaluating the success of the company designing the TQM System

    OpenAIRE

    Mitreva, Elizabeta; Taskov, Nako

    2014-01-01

    This paper proposes a methodology for evaluating the success of the designed and implemented system for TQM (audit) and its application in some Macedonian companies. Successful application of this methodology can only be achieved if business processes are designed and implemented with optimal utilization of resources, in order to work out the best from the first time, no defects, no loss of time and to the satisfaction of all users. This methodology has found a p...

  16. An estimate and evaluation of design error effects on nuclear power plant design adequacy

    International Nuclear Information System (INIS)

    Stevenson, J.D.

    1984-01-01

    An area of considerable concern in evaluating Design Control Quality Assurance procedures applied to design and analysis of nuclear power plant is the level of design error expected or encountered. There is very little published data 1 on the level of error typically found in nuclear power plant design calculations and even less on the impact such errors would be expected to have on overall design adequacy of the plant. This paper is concerned with design error associated with civil and mechanical structural design and analysis found in calculations which form part of the Design or Stress reports. These reports are meant to document the design basis and adequacy of the plant. The estimates contained in this paper are based on the personal experiences of the author. In Table 1 is a partial listing of the design docummentation review performed by the author on which the observations contained in this paper are based. In the preparation of any design calculations, it is a utopian dream to presume such calculations can be made error free. The intent of this paper is to define error levels which might be expected in a competent engineering organizations employing currently technically qualified engineers and accepted methods of Design Control. In addition, the effects of these errors on the probability of failure to meet applicable design code requirements also are estimated

  17. New knowledge network evaluation method for design rationale management

    Science.gov (United States)

    Jing, Shikai; Zhan, Hongfei; Liu, Jihong; Wang, Kuan; Jiang, Hao; Zhou, Jingtao

    2015-01-01

    Current design rationale (DR) systems have not demonstrated the value of the approach in practice since little attention is put to the evaluation method of DR knowledge. To systematize knowledge management process for future computer-aided DR applications, a prerequisite is to provide the measure for the DR knowledge. In this paper, a new knowledge network evaluation method for DR management is presented. The method characterizes the DR knowledge value from four perspectives, namely, the design rationale structure scale, association knowledge and reasoning ability, degree of design justification support and degree of knowledge representation conciseness. The DR knowledge comprehensive value is also measured by the proposed method. To validate the proposed method, different style of DR knowledge network and the performance of the proposed measure are discussed. The evaluation method has been applied in two realistic design cases and compared with the structural measures. The research proposes the DR knowledge evaluation method which can provide object metric and selection basis for the DR knowledge reuse during the product design process. In addition, the method is proved to be more effective guidance and support for the application and management of DR knowledge.

  18. Feedback from Usability Evaluation to User Interface Design

    DEFF Research Database (Denmark)

    Nielsen, C. M.; Overgaard, M.; Pedersen, M. B.

    2005-01-01

    This paper reports from an exploratory study of means for providing feedback from a usability evaluation to the user interface designers. In this study, we conducted a usability evaluation of a mobile system that is used by craftsmen to register use of time and materials. The results...... and weaknesses of the system. The findings indicate that detailed descriptions of problems and log descriptions of the user's interaction with the system and of system interaction are useful for the designers when trying to understand the usability problems that the users have encountered....

  19. Statistical evaluation of design-error related nuclear reactor accidents

    International Nuclear Information System (INIS)

    Ott, K.O.; Marchaterre, J.F.

    1981-01-01

    In this paper, general methodology for the statistical evaluation of design-error related accidents is proposed that can be applied to a variety of systems that evolves during the development of large-scale technologies. The evaluation aims at an estimate of the combined ''residual'' frequency of yet unknown types of accidents ''lurking'' in a certain technological system. A special categorization in incidents and accidents is introduced to define the events that should be jointly analyzed. The resulting formalism is applied to the development of U.S. nuclear power reactor technology, considering serious accidents (category 2 events) that involved, in the accident progression, a particular design inadequacy. 9 refs

  20. Design and evaluation of daylighting applications of holographic glazings

    Energy Technology Data Exchange (ETDEWEB)

    Papamichael, K.; Ehrlich, C.; Ward, G.

    1996-12-01

    According to the contractual agreement, BTP would develop a computer model of the POC holographic structures and then simulate the performance of alternative designs using the RADIANCE lighting and rendering computer program [Ward 1990]. The RADIANCE model would then be used to evaluate the daylight performance of alternative designs of holographic glazings in a prototypical office space. The simulation process would be validated against actual photometric measurements of holographic glazing samples developed by POC. The results would be used to evaluate the potential for increased electric lighting savings through increased daylight illuminance levels at distances more than 15 ft--20 ft (4.6 m--6.1 m ) from the window wall.

  1. Including severe accidents in the design basis of nuclear power plants: An organizational factors perspective after the Fukushima accident

    International Nuclear Information System (INIS)

    Alvarenga, M.A.B.; Frutuoso e Melo, P.F.

    2015-01-01

    Highlights: • The Fukushima accident was man-made and not caused by natural phenomena. • Vulnerabilities were known by regulator and licensee but measures were not taken. • There was lack of independence and transparency of the regulatory body. • Laws and regulations have not been updated to international standards. • Organizational failures have played an important role in the Fukushima accident. - Abstract: The Fukushima accident was clearly an accident made by humans and not caused by natural phenomena as was initially thought. Vulnerabilities were known by both regulators and operator but they postponed measures. The emergency plan was not effective in protecting the public, because the involved parties were not sufficiently prepared to make the right decisions. The shortcomings and faults mentioned above resulted from the lack of independence and transparency of the regulatory body. Even laws and regulations, and technical standards, have not been upgraded to international standards. Regulators have not defined requirements and left for the operator to decide what would be more appropriate. In this aspect, there was clearly a lack of independence between these bodies and operator’s lobby power. The above situation raised the question of urgent updating of institutions, in particular those responsible for nuclear safety. The above evidences show that several nuclear safety principles were not followed. This paper intends to highlight some existing safety criteria that were developed from the operational experience of the severe accidents that occurred at TMI and Chernobyl that should be incorporated in the design of new nuclear power plants and to provide appropriate design changes (backfittings) for reactors that belong to the previous generation prior to the occurrence of these accidents, through the study of design vulnerabilities. Furthermore, the main criteria that define an effective regulatory agency are also discussed. Although these

  2. SSFI and SSOMI new method of evaluating design

    International Nuclear Information System (INIS)

    Tolson, G.M.

    1992-01-01

    The NRC has developed a new inspection method which has proven its effectiveness in evaluating design organizations. The new method is used in two types of NRC inspections, Safety System Functional Inspection (SSFI), and Safety System Outage Modification Inspection (SSOMI). The SSFI/SSOMI audits were developed following an event which brought a nuclear power plant close to a core meltdown. That event was caused by a series of problems which would not have been found using conventional methods. The SSFI and SSOMI audits involve intense technical evaluation of a nuclear system to determine wheter the system will function as designed. The SSFI/SSOMI method normally uses eight to fifteen engineers with different fields of expertise to evaluate a system, or a change to a system in the case of a SSOMI. The effectiveness of each engineer's input is amplified in a series of open, questioning, free-wheeling, brainstorming-type team meetings. During the team meetings, all aspects of the audit are controlled by a consensus of the team members. The findings from these new methods are surprisingly consistent, regardless of which organization is audited or which organization performs the audit. This consistency implies a widespread generic weakness in the manner design is being performed. This paper addresses generic findings and recommends increased use of these new methods to evaluate design organizations. These audit methods can be readily used to evaluate any process or system. (orig.)

  3. Seismic evaluation of a cooling water reservoir facility including fluid-structure and soil-structure interaction effects

    International Nuclear Information System (INIS)

    Kabir, A.F.; Maryak, M.E.

    1991-01-01

    Seismic analyses and structural evaluations were performed for a cooling water reservoir of a nuclear reactor facility. The horizontal input seismic motion was the NRC Reg. guide 1.60 spectrum shape anchored at 0.20g zero period acceleration. Vertical input was taken as two-thirds of the horizontal input. Soil structure interaction and hydrodynamic effects were addressed in the seismic analyses. Uncertainties in the soil properties were accounted for by considering three soil profiles. Two 2-dimensional SSI models and a 3-dimensional static model. Representing different areas of the reservoir structures were developed and analyzed to obtain seismic forces and moments, and accelerations at various locations. The results included in this paper indicated that both hydrodynamic and soil-structure interaction effects are significant contributors to the seismic responses of the water-retaining walls of the reservoir

  4. Design data and safety features of commercial nuclear power plants including cumulative index for Volumes I--VI

    International Nuclear Information System (INIS)

    Heddleson, F.A.

    1977-01-01

    Design data, safety features, and site characteristics are summarized for 12 nuclear power units in 6 power stations in the United States. Six pages of data are presented for each station, consisting of thermal-hydraulic and nuclear factors, containment features, emergency-core-cooling systems, site features, circulating water system data, and miscellaneous factors. In addition, an aerial perspective is presented for each plant. This volume covers plants with docket numbers 50-553 through 50-569 (Phipps Bend, Black Fox, Yellow Creek, and NEP) and two earlier plants not previously reported--Hope Creek (50-354, 50-355) and WPPSS 1 and 4 (50-460, 50-513). Indexes for this volume and the five earlier volumes are presented in three forms--by docket number, by plant name, and by participating utility

  5. Analytical and Experimental Performance Evaluation of BLE Neighbor Discovery Process Including Non-Idealities of Real Chipsets

    Directory of Open Access Journals (Sweden)

    David Perez-Diaz de Cerio

    2017-03-01

    Full Text Available The purpose of this paper is to evaluate from a real perspective the performance of Bluetooth Low Energy (BLE as a technology that enables fast and reliable discovery of a large number of users/devices in a short period of time. The BLE standard specifies a wide range of configurable parameter values that determine the discovery process and need to be set according to the particular application requirements. Many previous works have been addressed to investigate the discovery process through analytical and simulation models, according to the ideal specification of the standard. However, measurements show that additional scanning gaps appear in the scanning process, which reduce the discovery capabilities. These gaps have been identified in all of the analyzed devices and respond to both regular patterns and variable events associated with the decoding process. We have demonstrated that these non-idealities, which are not taken into account in other studies, have a severe impact on the discovery process performance. Extensive performance evaluation for a varying number of devices and feasible parameter combinations has been done by comparing simulations and experimental measurements. This work also includes a simple mathematical model that closely matches both the standard implementation and the different chipset peculiarities for any possible parameter value specified in the standard and for any number of simultaneous advertising devices under scanner coverage.

  6. Guide for Operational Configuration Management Program including the adjunct programs of design reconstitution and material condition and aging management

    International Nuclear Information System (INIS)

    1993-11-01

    This standard presents program criteria and implementation guidance for an operational configuration management program for DOE nuclear and non-nuclear facilities in the operational phase. Portions of this standard are also useful for other DOE processes, activities, and programs. This Part 1 contains foreword, glossary, acronyms, bibliography, and Chapter 1 on operational configuration management program principles. Appendices are included on configuration management program interfaces, and background material and concepts for operational configuration management

  7. Analysis and Evaluation of Statistical Models for Integrated Circuits Design

    Directory of Open Access Journals (Sweden)

    Sáenz-Noval J.J.

    2011-10-01

    Full Text Available Statistical models for integrated circuits (IC allow us to estimate the percentage of acceptable devices in the batch before fabrication. Actually, Pelgrom is the statistical model most accepted in the industry; however it was derived from a micrometer technology, which does not guarantee reliability in nanometric manufacturing processes. This work considers three of the most relevant statistical models in the industry and evaluates their limitations and advantages in analog design, so that the designer has a better criterion to make a choice. Moreover, it shows how several statistical models can be used for each one of the stages and design purposes.

  8. Performance of Transuranic-Loaded Fully Ceramic Micro-Encapsulated Fuel in LWRs Final Report, Including Void Reactivity Evaluation

    International Nuclear Information System (INIS)

    Pope, Michael A.; Sen, R. Sonat; Boer, Brian; Ougouag, Abderrafi M.; Youinou, Gilles

    2011-01-01

    The current focus of the Deep Burn Project is on once-through burning of transuranics (TRU) in light-water reactors (LWRs). The fuel form is called Fully-Ceramic Micro-encapsulated (FCM) fuel, a concept that borrows the tri-isotropic (TRISO) fuel particle design from high-temperature reactor technology. In the Deep Burn LWR (DB-LWR) concept, these fuel particles are pressed into compacts using SiC matrix material and loaded into fuel pins for use in conventional LWRs. The TRU loading comes from the spent fuel of a conventional LWR after 5 years of cooling. Unit cell and assembly calculations have been performed using the DRAGON-4 code to assess the physics attributes of TRU-only FCM fuel in an LWR lattice. Depletion calculations assuming an infinite lattice condition were performed with calculations of various reactivity coefficients performed at each step. Unit cells and assemblies containing typical UO2 and mixed oxide (MOX) fuel were analyzed in the same way to provide a baseline against which to compare the TRU-only FCM fuel. Then, assembly calculations were performed evaluating the performance of heterogeneous arrangements of TRU-only FCM fuel pins along with UO2 pins.

  9. Evaluation of mini super computers for nuclear design applications

    International Nuclear Information System (INIS)

    Altomare, S.; Baradari, F.

    1987-01-01

    The evolution of the mini super computers will force changes from the current environment of performing nuclear design calculations on mainframe computers (such as a CRAY) to mini super computers. This change will come about for a number of reasons. First, the mini super computers currently available in the marketplace offer the power and speed comparable to mainframes and can provide the capability to support highly computer intensive calculations. Second, the equipment is physically smaller and can easily be installed and operated without extensive investments in facilities and operations support. Third, the computer capacity can be acquired with as much needed memory, disk, and tape capacity as may be needed. Another reasons is that the performance/cost ratio has increased drastically as hardware costs have decreased. A study was conducted at the Westinghouse Commercial Nuclear Fuel Division (CNFD) to evaluate the mini super computers for use in nuclear core design. As a result of this evaluation, Westinghouse CNFD is offering a combined hardware/software technology transfer package for core design. This package provides the utility designer with a totally dedicated mini super computer comparable in speed to the CRAY 1S with sufficient capacity for a sizable design group to perform the engineering activities related to nuclear core design and operations support. This also assures the utility of being totally compatible with the CNFD design codes, thus assuring total update compatibility

  10. High performance APCS conceptual design and evaluation scoping study

    International Nuclear Information System (INIS)

    Soelberg, N.; Liekhus, K.; Chambers, A.; Anderson, G.

    1998-02-01

    This Air Pollution Control System (APCS) Conceptual Design and Evaluation study was conducted to evaluate a high-performance (APC) system for minimizing air emissions from mixed waste thermal treatment systems. Seven variations of high-performance APCS designs were conceptualized using several design objectives. One of the system designs was selected for detailed process simulation using ASPEN PLUS to determine material and energy balances and evaluate performance. Installed system capital costs were also estimated. Sensitivity studies were conducted to evaluate the incremental cost and benefit of added carbon adsorber beds for mercury control, specific catalytic reduction for NO x control, and offgas retention tanks for holding the offgas until sample analysis is conducted to verify that the offgas meets emission limits. Results show that the high-performance dry-wet APCS can easily meet all expected emission limits except for possibly mercury. The capability to achieve high levels of mercury control (potentially necessary for thermally treating some DOE mixed streams) could not be validated using current performance data for mercury control technologies. The engineering approach and ASPEN PLUS modeling tool developed and used in this study identified APC equipment and system performance, size, cost, and other issues that are not yet resolved. These issues need to be addressed in feasibility studies and conceptual designs for new facilities or for determining how to modify existing facilities to meet expected emission limits. The ASPEN PLUS process simulation with current and refined input assumptions and calculations can be used to provide system performance information for decision-making, identifying best options, estimating costs, reducing the potential for emission violations, providing information needed for waste flow analysis, incorporating new APCS technologies in existing designs, or performing facility design and permitting activities

  11. Short-term Evaluation of a Comprehensive Education Program Including Inhaler Training and Disease Management on Chronic Obstructive Pulmonary Disease.

    Science.gov (United States)

    Yoo, Kwang Ha; Chung, Wou Young; Park, Joo Hun; Hwang, Sung Chul; Kim, Tae Eun; Oh, Min Jung; Kang, Dae Ryong; Rhee, Chin Kook; Yoon, Hyoung Kyu; Kim, Tae Hyung; Kim, Deog Kyeom; Park, Yong Bum; Kim, Sang Ha; Yum, Ho Kee

    2017-10-01

    Proper education regarding inhaler usage and optimal management of chronic obstructive pulmonary disease (COPD) is essential for effectively treating patients with COPD. This study was conducted to evaluate the effects of a comprehensive education program including inhaler training and COPD management. We enlisted 127 patients with COPD on an outpatient basis at 43 private clinics in Korea. The patients were educated on inhaler usage and disease management for three visits across 2 weeks. Physicians and patients were administered a COPD assessment test (CAT) and questionnaires about the correct usage of inhalers and management of COPD before commencement of this program and after their third visit. The outcomes of 127 COPD patients were analyzed. CAT scores (19.6±12.5 vs. 15.1±12.3) improved significantly after this program (pmanagement and the correct technique for using inhalers than those who did not have improved CAT scores (peducation program including inhaler training and COPD management at a primary care setting improved CAT scores and led to patients' better understanding of COPD management. Copyright©2017. The Korean Academy of Tuberculosis and Respiratory Diseases

  12. Design, Construction and Evaluation of Wild Pistachio Sheller

    Directory of Open Access Journals (Sweden)

    F Karimi

    2014-09-01

    Full Text Available The wild pistachio (Pistacia Atlantica Mutika exists in 2.4 million hectares of Iranian forest. In spite of high nutritional and medical value of this fruit, its use and processing are still performed manually. The objectives of this research are to design, to construct and to evaluate the performance of a pistachio hulling machine. The pistachio of Kerman province was chosen as the case of study. The mechanism of shelling was chosen based on the applied pressure force of two cylinders, driving and driven. The effects of input variables including revolution of driving cylinder (three levels, the gap between two cylinders (four levels and moisture content (four levels on the performance of machine (shelling efficiency, percentage of intact kernel, percentage of imperfective broken nut, percentage of dust, and percentage of unshelled nut were analyzed. The results showed that the shelling efficiency decreases with increasing the gap of two cylinders and moisture content of wild pistachio. The maximum intact kernel was obtained at moisture content of 6.61 wb %. The best performance was observed with the following conditions: the cylinders’ gap of 0.48 mm, rotational speed of the driving cylinder of 25.84 rpm and moisture content of 4.31% w.b.

  13. Design and modeling of an advanced marine machinery system including waste heat recovery and removal of sulphur oxides

    DEFF Research Database (Denmark)

    Frimann Nielsen, Rasmus; Haglind, Fredrik; Larsen, Ulrik

    2013-01-01

    -stroke diesel engine and a conventional waste heat recovery system. The results suggest that an organic Rankine cycle placed after the conventional waste heat recovery system is able to extract the sulphuric acid from the exhaust gas, while at the same time increase power generation from waste heat by 32...... consists of a two-stroke diesel engine, the wet sulphuric process for sulphur removal and an advanced waste heat recovery system including a conventional steam Rankine cycle and an organic Rankine cycle. The results are compared with those of a state-of-the-art machinery system featuring a two...

  14. Situated Research Design and Methodological Choices in Formative Program Evaluation

    Science.gov (United States)

    Supovitz, Jonathan

    2013-01-01

    Design-based implementation research offers the opportunity to rethink the relationships between intervention, research, and situation to better attune research and evaluation to the program development process. Using a heuristic called the intervention development curve, I describe the rough trajectory that programs typically follow as they…

  15. Designing and evaluating the tabletop game experience for senior citizens

    NARCIS (Netherlands)

    Al Mahmud, A.; Mubin, O.; Shahid, C.S.; Martens, J.B.O.S.

    2008-01-01

    In this paper, we report on the design and evaluation of a tabletop game especially created for senior citizens. The game is intended to provide leisure and fun and is played with four players on an augmented tabletop. It evolved from existing games and rules that are popular and familiar amongst

  16. Improving the Interplay between Usability Evaluation and User Interface Design

    DEFF Research Database (Denmark)

    Hornbæk, K.; Stage, Jan

    2004-01-01

    of the workshop are motivated and an outline of the contents of the papers that were presented in the workshop is given. In addition we summarize some challenges to the interplay between usability evaluation and user interface design agreed upon at the workshop, as well as some solutions that were debated....

  17. Design, implementation, and evaluation of the Resilient Smalltalk embedded platform

    DEFF Research Database (Denmark)

    Andersen, Jacob Robert; Bak, Lars; Grarup, Steffen

    2005-01-01

    machine running on embedded systems. Programmers may connect to running virtual machines and service, monitor, or change the running systems. Furthermore, we present an evaluation of the Resilient platform in relation to the design goals through a case study of two development projects which successfully...

  18. Study Design and Data Gathering Guide for Serious Games’ Evaluation

    NARCIS (Netherlands)

    Baalsrud Hauge, Jannicke; Boyle, Elizabeth; Mayer, Igor; Nadolski, Rob; Riedel, Johann C. K. H.; Moreno-Ger, Pablo; Bellotti, Francesco; Lim, Theodore; Ritchie, James

    2013-01-01

    Baalsrud Hauge, J., Boyle, E., Mayer, I., Nadolski, R. J., Riedel, J. C. K. H., Moreno-Ger, P., Bellotti, F., Lim, T., & Ritchie, J. (2013). Study Design and Data Gathering Guide for Serious Games’ Evaluation. In T. M. Connolly, T. Hainey, E. Boyle, G. Baxter, & P. Moreno-Ger (Eds.), Psychology,

  19. Molecular design, synthesis and evaluation of chemical biology tools

    NARCIS (Netherlands)

    Hoogenboom, Jorin

    2017-01-01

    Chapter 1 provides a perspective of synthetic organic chemistry as a discipline involved in the design, synthesis and evaluation of complex molecules. The reader is introduced with a brief history of synthetic organic chemistry, all the while dealing with different aspects of

  20. Design and techno economic evaluation of biomass gasifier for ...

    African Journals Online (AJOL)

    This paper addresses the design, performance and economic evaluation of biomass based open core downdraft gasifier for industrial process heat application. The gasifier is having feed rate as 90 kg h-1 and producing about 850 MJ h-1 of heat. The gasifier has been installed in M/S Phosphate India Pvt. Limited, Udaipur ...

  1. Physiological evaluation of a newly designed lever mechanism for wheelchairs

    NARCIS (Netherlands)

    van der Woude, L H; Veeger, DirkJan (H. E. J.); de Boer, Y; Rozendal, R H

    1993-01-01

    Lever-propelled wheelchairs have been described as more efficient and less physically demanding than hand-rim-propelled wheelchairs. To evaluate a newly designed lever mechanism (MARC) in both one- and two-arm use, a series of wheelchair exercise tests were performed on a motor-driven treadmill.

  2. Designing, Teaching, and Evaluating Two Complementary Mixed Methods Research Courses

    Science.gov (United States)

    Christ, Thomas W.

    2009-01-01

    Teaching mixed methods research is difficult. This longitudinal explanatory study examined how two classes were designed, taught, and evaluated. Curriculum, Research, and Teaching (EDCS-606) and Mixed Methods Research (EDCS-780) used a research proposal generation process to highlight the importance of the purpose, research question and…

  3. Conceptual design study for the demonstration reactor of JSFR. (3) Safety design and evaluation

    International Nuclear Information System (INIS)

    Tani, Akihiro; Shimakawa, Yoshio; Kubo, Shigenobu; Fujimura, Ken; Yamano, Hidemasa

    2011-01-01

    This paper describes the result of conceptual safety design and evaluation for the demonstration plant of Japan sodium-cooled fast reactor (JSFR), which was preliminarily conducted for providing information necessary to decide the plant specification for further design study. The plant major specifications except for output power and safety design concept are almost the same as those of the commercial JSFR. A set of safety evaluation for typical design basis events (DBEs) is mainly focused here, which was conducted for the 750 MWe design. Safety analyses for DBEs evaluation were performed on the basis of conservative assumptions using a one-dimensional flow network code with point kinetics. For representative DBEs, transient over power type events and loss of flow type events were analyzed. The long-term loss-of-offsite power event was also calculated to evaluate the natural circulation decay heat removal system. All analytical results showed to meet tentative safety criteria, thus it was confirmed that the safety design concept of JSFR is feasible against DBEs. (author)

  4. Improved fuel design economics - a new evaluation tool

    International Nuclear Information System (INIS)

    Aboudara, J.L.

    1987-01-01

    Advanced fuel design technology is now beginning to be implemented with new reload regions for large pressurized water reactors. Until recently there has not been an integrated computer modeling product that would allow easy assessment of the economics of various advanced fuel design alternatives now available to utilities. The Fuel Cycle Scoping System (FCSS) was designed to fill this need. The FCSS is a personnel computer (PC) software package that is used to evaluate alternative strategies for supplying and using nuclear fuel in nuclear power reactors. The FCSS is an extremely flexible package that permits evaluation of in-core and out-of-core fuel management strategy options. For each strategy option, unit and reactor operating assumptions and assumptions for uranium supply, conversion, enrichment, fabrication, and spent fuel disposal can be made

  5. Array design and expression evaluation in POOMA II

    Energy Technology Data Exchange (ETDEWEB)

    Karmesin, S.; Crotinger, J.; Cummings, J.; Haney, S.; Humphrey, W.; Reynders, J.; Smith, S.; Williams, T.J.

    1998-12-31

    POOMA is a templated C++ class library for use in the development of large-scale scientific simulations on serial and parallel computers. POOMA II is a new design and implementation of POOMA intended to add richer capabilities and greater flexibility to the framework. The new design employs a generic Array class that acts as an interface to, or view on, a wide variety of data representation objects referred to as engines. This design separates the interface and the representation of multidimensional arrays. The separation is achieved using compile-time techniques rather than virtual functions, and thus code efficiency is maintained. POOMA II uses PETE, the Portable Expression Template Engine, to efficiently represent complex mathematical expressions involving arrays and other objects. The representation of expressions is kept separate from expression evaluation, allowing the use of multiple evaluator mechanisms that can support nested where-block constructs, hardware-specific optimizations and different run-time environments.

  6. Diabetic Mario: Designing and Evaluating Mobile Games for Diabetes Education.

    Science.gov (United States)

    Baghaei, Nilufar; Nandigam, David; Casey, John; Direito, Artur; Maddison, Ralph

    2016-08-01

    Traditionally, diabetes education has relied on written materials, with limited resources available for children with diabetes. Mobile games can be effective and motivating tools for the promotion of children's health. In our earlier work, we proposed a novel approach for designing computer games aimed at educating children with diabetes. In this article, we apply our game design to a mobile Android game (Mario Brothers). We also introduce four heuristics that are specifically designed for evaluating the mobile game, by adapting traditional usability heuristics. Results of a pilot study (n = 12) to evaluate gameplay over 1-week showed that the children found the game engaging and improved their knowledge of healthy diet and lifestyle.

  7. Technical Details on Beyond Design Basis Event Pilot Evaluations

    Energy Technology Data Exchange (ETDEWEB)

    None, None

    2013-01-01

    The primary focus of the BDBE pilot project was the review of BDBE analysis and mitigation features at four DOE nuclear facilities representing a range of DOE sites, nuclear facility types/activities, and responsible program offices. The pilots looked at (1) how beyond design basis accidents were evaluated and documented in the facility Documented Safety Analysis, (2) potential BDBE vulnerabilities and margins to failure of facility safety features as obtained from general area and specific system walkdowns and design documents reviews, and (3) preparations made in facility and site emergency management programs to respond to severe accidents. It also evaluated whether draft BDBE guidance on safety analysis and emergency management could be used to improve the analysis of and preparations for mitigating severe and beyond design basis accidents. The details of these activities are organized in this report as described below.

  8. Requirements of Integrated Design Teams While Evaluating Advanced Energy Retrofit Design Options in Immersive Virtual Environments

    Directory of Open Access Journals (Sweden)

    Xue Yang

    2015-12-01

    Full Text Available One of the significant ways to save energy use in buildings is to implement advanced energy retrofits in existing buildings. Improving energy performance of buildings through advanced energy retrofitting requires a clear understanding of the cost and energy implications of design alternatives from various engineering disciplines when different retrofit options are considered. The communication of retrofit design alternatives and their energy implications is essential in the decision-making process, as it affects the final retrofit selections and hence the energy efficiency of the retrofitted buildings. The objective of the research presented here was to identify a generic list of information requirements that are needed to be shared and collectively analyzed by integrated design teams during advanced energy retrofit design review meetings held in immersive settings. While identifying such requirements, the authors used an immersive environment based iterative requirements elicitation approach. The technology was used as a means to better identify the information requirements of integrated design teams to be analyzed as a group. This paper provides findings on information requirements of integrated design teams when evaluating retrofit options in immersive virtual environments. The information requirements were identified through interactions with sixteen experts in design and energy modeling domain, and validated with another group of participants consisting of six design experts who were experienced in integrated design processes. Industry practitioners can use the findings in deciding on what information to share with integrated design team members during design review meetings that utilize immersive virtual environments.

  9. Evaluation of preconceptual plug designs using experts' judgement

    International Nuclear Information System (INIS)

    Sioshansi, F.P.; O'Rourke, J.E.

    1980-03-01

    A number of preconceptual plug designs for an underground nuclear waste repository were to be evaluated based on the available information on plug materials and placement techniques. Because of complex environment and loading conditions, long time frame under consideration, rigid performance characteristics and considerable uncertainties present in preconceptual design and material properties, a qualitative and judgmental evaluation procedure was needed to supplement technical studies. A structured procedure was developed to qualitatively capture evaluator's views and reservations on the proposed preconceptual schemes. Since a thorough evaluation of each proposed plug scheme required in-depth experience and familiarity with many components of the plug, three knowledgeable experts with specialties in the most relevant aspects of the problem were independently interviewed. Each plug scheme was broken down into three subcomponents and each subcomponent was evaluated separately. The proposed schemes were then rated taking their subcomponents into consideration. Because the experts had different specialties, their subcomponent and overall ratings were not in full agreement. Each plug scheme's lowest overall rating was used as the most significant determinant of the judgmental preference categories reported in this study. The approach used discriminated between the proposed schemes for those with highest probability of being successful. The most preferred schemes were then reviewed with respect to the data produced in the technical analysis performed during the project. The results of the judgmental analysis were then synthesized and modified with results of the technical analysis to produce the preconceptual plug designs

  10. Short-term evaluation of arthroscopic management of tennis elbow; including resection of radio-capitellar capsular complex.

    Science.gov (United States)

    Babaqi, AbdulRahman A; Kotb, Mohammed M; Said, Hatem G; AbdelHamid, Mohamed M; ElKady, Hesham A; ElAssal, Maher A

    2014-06-01

    There has been controversy regarding the pathogenesis and treatment of lateral epicondylitis. Different surgical techniques for the treatment of lateral epicondylitis prescribed. The purpose of this study was to evaluate the short-term outcomes of arthroscopic management including resection of the radio-capitellar capsular complex, using different validated scores. In this study, arthroscopic resection of a capsular fringe complex was done beside debridement of the undersurface of Extensor Carpi Radialis Brevis (ECRB). Thirty-one patients with recalcitrant lateral epicondylitis for a minimum of 6 months had surgery. In all patients, a collar-like band of radio-capitellar capsular complex was found to impinge on the radial head and subluxate into the radio-capitellar joint with manipulation under direct vision. Outcomes were assessed using Mayo Elbow Performance Index (MEPI), the Patient-Rated Tennis Elbow Evaluation (PRTEE), and the Disability of the Arm, Shoulder, and Hand (DASH), beside visual analog scale (VAS) for pain and satisfaction criteria. After arthroscopic surgery, overall satisfaction was extremely positive, over the 31 patients, 93.5% of the patients are satisfied. The mean score for pain improved from 8.64 to 1.48 points. The total PRTEE improved from 55.53 to 10.39 points. The mean MEPI score was improved from 61.82 to 94.10 points. DASH score also improved from 24.46 to 4.81 points. All improvements are statistically significant (P < 0.05). Arthroscopic release of ECRB in patients with chronic lateral epicondylitis is a reproducible method with a marked improvement in function within a short period, with special consideration for resection of radio-capitellar capsular complex.

  11. Performance of portland limestone cements: Cements designed to be more sustainable that include up to 15% limestone addition

    Science.gov (United States)

    Barrett, Timothy J.

    In 2009, ASTM and AASHTO permitted the use of up to 5% interground limestone in ordinary portland cement (OPC) as a part of a change to ASTM C150/AASHTO M85. When this work was initiated a new proposal was being discussed that would enable up to 15% interground limestone cement to be considered in ASTM C595/AASHTO M234. This work served to provide rapid feedback to the state department of transportation and concrete industry for use in discussions regarding these specifications. Since the time this work was initiated, ASTM C595/AASHTO M234 was passed (2012c) and PLCs are now able to be specified, however they are still not widely used. The proposal for increasing the volume of limestone that would be permitted to be interground in cement is designed to enable more sustainable construction, which may significantly reduce the CO2 that is embodied in the built infrastructure while also extending the life of cement quarries. Research regarding the performance of cements with interground limestone has been conducted by the cement industry since these cements became widely used in Europe over three decades ago, however this work focuses on North American Portland Limestone Cements (PLCs) which are specifically designed to achieve similar performance as the OPCs they replace.This thesis presents a two-phase study in which the potential for application of cements containing limestone was assessed. The first phase of this study utilized a fundamental approach to determine whether cement with up to 15% of interground or blended limestone can be used as a direct substitute to ordinary portland cement. The second phase of the study assessed the concern of early age shrinkage and cracking potential when using PLCs, as these cements are typically ground finer than their OPC counterparts. For the first phase of the study, three commercially produced PLCs were obtained and compared to three commercially produced OPCs made from the same clinker. An additional cement was tested

  12. Using Concrete and Realistic Data in Evaluating Initial Visualization Designs

    DEFF Research Database (Denmark)

    Knudsen, Søren; Pedersen, Jeppe Gerner; Herdal, Thor

    2016-01-01

    We explore means of designing and evaluating initial visualization ideas, with concrete and realistic data in cases where data is not readily available. Our approach is useful in exploring new domains and avenues for visualization, and contrasts other visualization work, which typically operate...... under the assumption that data has already been collected, and is ready to be visualized. We argue that it is sensible to understand data requirements and evaluate the potential value of visualization before devising means of automatic data collection. We base our exploration on three cases selected...... the design case and problem, the manner in which we collected data, and the findings obtained from evaluations. Afterwards, we describe four factors of our data collection approach, and discuss potential outcomes from it....

  13. ECH system developments including the design of an intelligent fault processor on the DIII-D tokamak

    International Nuclear Information System (INIS)

    Ponce, D.; Lohr, J.; Tooker, J.F.; O'Neill, R.C.; Moeller, C.P.; Doane, J.L.; Noraky, S.; Dubovenko, K.; Gorelov, Y.A.; Cengher, M.; Penaflor, B.G.; Ellis, R.A.

    2011-01-01

    A new generation fault processor is in development which is intended to increase fault handling flexibility and reduce the number of incomplete DIII-D shots due to gyrotron faults. The processor, which is based upon a field programmable gate array device, will analyze signals for aberrant operation and ramp down high voltage to try to avoid hard faults. The processor will then attempt to ramp back up to an attainable operating point. The new generation fault processor will be developed during an expansion of the electron cyclotron heating (ECH) areas that will include the installation of a depressed collector gyrotron and associated equipment. Existing systems will also be upgraded. Testing of real-time control of the ECH launcher poloidal drives by the DIII-D plasma control system will be completed. The ECH control system software will be upgraded for increased scalability and to increase operator productivity. Resources permitting, all systems will receive an extra layer of interlocks for the filament and magnet power supplies, added shielding for the tank electronics, programmable filament boost shape for long pulses, and electronics upgrades for the installation of the advanced fault processor.

  14. Evaluation of low-frequency operational limit of proposed ITER low-field-side reflectometer waveguide run including miter bends

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Guiding [Univ. of California, Los Angeles, CA (United States). Dept. of Physics and Astronomy and Plasma Science and Technology Inst. (PSTI); Peebles, W. A. [Univ. of California, Los Angeles, CA (United States). Dept. of Physics and Astronomy and Plasma Science and Technology Inst. (PSTI); Doyle, E. J. [Univ. of California, Los Angeles, CA (United States). Dept. of Physics and Astronomy and Plasma Science and Technology Inst. (PSTI); Crocker, N. A. [Univ. of California, Los Angeles, CA (United States). Dept. of Physics and Astronomy and Plasma Science and Technology Inst. (PSTI); Wannberg, C. [Univ. of California, Los Angeles, CA (United States). Dept. of Physics and Astronomy and Plasma Science and Technology Inst. (PSTI); Lau, Cornwall H. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hanson, Gregory R. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Doane, John L. [General Atomics, San Diego, CA (United States)

    2017-10-19

    The present design concept for the ITER low-field-side reflectometer transmission line (TL) consists of an ~40 m long, 6.35 cm diameter helically corrugated waveguide (WG) together with ten 90° miter bends. This paper presents an evaluation of the TL performance at low frequencies (33-50 GHz) where the predicted HE11 mode ohmic and mode conversion losses start to increase significantly. Quasi-optical techniques were used to form a near Gaussian beam to efficiently couple radiation in this frequency range into the WG. We observed that the output beams from the guide remained linearly polarized with cross-polarization power levels of ~1.5%-3%. The polarization rotation due to the helical corrugations was in the range ~1°-3°. The radiated beam power profiles typically show excellent Gaussian propagation characteristics at distances >20 cm from the final exit aperture. The round trip propagation loss was found to be ~2.5 dB at 50 GHz and ~6.5 dB at 35 GHz, showing an inverse increase with frequency. This was consistent with updated calculations of miter bend and ohmic losses. At low frequencies (33-50 GHz), the mode purity remained very good at the exit of the waveguide, and the losses are perfectly acceptable for operation in ITER. Finally, the primary challenge may come from the future addition of a Gaussian telescope and other filter components within the corrugated guide, which will likely introduce additional perturbations to the beam profile and an increase in mode-conversion loss.

  15. Adult vaccination strategies for the control of pertussis in the United States: an economic evaluation including the dynamic population effects.

    Directory of Open Access Journals (Sweden)

    Laurent Coudeville

    Full Text Available BACKGROUND: Prior economic evaluations of adult and adolescent vaccination strategies against pertussis have reached disparate conclusions. Using static approaches only, previous studies failed to analytically include the indirect benefits derived from herd immunity as well as the impact of vaccination on the evolution of disease incidence over time. METHODS: We assessed the impact of different pertussis vaccination strategies using a dynamic compartmental model able to consider pertussis transmission. We then combined the results with economic data to estimate the relative cost-effectiveness of pertussis immunization strategies for adolescents and adults in the US. The analysis compares combinations of programs targeting adolescents, parents of newborns (i.e. cocoon strategy, or adults of various ages. RESULTS: In the absence of adolescent or adult vaccination, pertussis incidence among adults is predicted to more than double in 20 years. Implementing an adult program in addition to childhood and adolescent vaccination either based on 1 a cocoon strategy and a single booster dose or 2 a decennial routine vaccination would maintain a low level of pertussis incidence in the long run for all age groups (respectively 30 and 20 cases per 100,000 person years. These strategies would also result in significant reductions of pertussis costs (between -77% and -80% including additional vaccination costs. The cocoon strategy complemented by a single booster dose is the most cost-effective one, whereas the decennial adult vaccination is slightly more effective in the long run. CONCLUSIONS: By providing a high level of disease control, the implementation of an adult vaccination program against pertussis appears to be highly cost-effective and often cost-saving.

  16. Evaluation of masonry wall design at nuclear power plants

    International Nuclear Information System (INIS)

    Con, V.N.; Subramonian, N.; Chokshi, N.

    1983-01-01

    The structural integrity of safety-related masonry walls in operating nuclear power plants may not be maintained when subjected to certain loads and load combinations. The paper presents some findings based upon the review of the design and analysis procedures used by the licensees in the reevaluation of safety-related masonry walls. The design criteria developed by the Structural Engineering Branch (SEB) of the United States Nuclear Regulatory Commission (NRC) along with other standard codes such as the Uniform Building Code, ACI 531-79, ATC 3-06, and NCMA were used as guidance in evaluating the design criteria developed by the licensees. The paper deals with the following subject areas: loads and load combinations, allowable stresses, analytical procedures, and modification methods. The paper concludes that, in general, the masonry walls in nuclear power plants comply with the working stress design requirements. In some cases, certain nonlinear analysis methods were used. The applicability of these methods is discussed. (orig.)

  17. Designing and recruiting to UK autism spectrum disorder research databases: do they include representative children with valid ASD diagnoses?

    Science.gov (United States)

    Warnell, F; George, B; McConachie, H; Johnson, M; Hardy, R; Parr, J R

    2015-09-04

    (1) Describe how the Autism Spectrum Database-UK (ASD-UK) was established; (2) investigate the representativeness of the first 1000 children and families who participated, compared to those who chose not to; (3) investigate the reliability of the parent-reported Autism Spectrum Disorder (ASD) diagnoses, and present evidence about the validity of diagnoses, that is, whether children recruited actually have an ASD; (4) present evidence about the representativeness of the ASD-UK children and families, by comparing their characteristics with the first 1000 children and families from the regional Database of children with ASD living in the North East (Dasl(n)e), and children and families identified from epidemiological studies. Recruitment through a network of 50 UK child health teams and self-referral. Parents/carers with a child with ASD, aged 2-16 years, completed questionnaires about ASD and some gave professionals' reports about their children. 1000 families registered with ASD-UK in 30 months. Children of families who participated, and of the 208 who chose not to, were found to be very similar on: gender ratio, year of birth, ASD diagnosis and social deprivation score. The reliability of parent-reported ASD diagnoses of children was very high when compared with clinical reports (over 96%); no database child without ASD was identified. A comparison of gender, ASD diagnosis, age at diagnosis, school placement, learning disability, and deprivation score of children and families from ASD-UK with 1084 children and families from Dasl(n)e, and families from population studies, showed that ASD-UK families are representative of families of children with ASD overall. ASD-UK includes families providing parent-reported data about their child and family, who appear to be broadly representative of UK children with ASD. Families continue to join the databases and more than 3000 families can now be contacted by researchers about UK autism research. Published by the BMJ

  18. Model Selection and Evaluation Based on Emerging Infectious Disease Data Sets including A/H1N1 and Ebola

    Directory of Open Access Journals (Sweden)

    Wendi Liu

    2015-01-01

    Full Text Available The aim of the present study is to apply simple ODE models in the area of modeling the spread of emerging infectious diseases and show the importance of model selection in estimating parameters, the basic reproduction number, turning point, and final size. To quantify the plausibility of each model, given the data and the set of four models including Logistic, Gompertz, Rosenzweg, and Richards models, the Bayes factors are calculated and the precise estimates of the best fitted model parameters and key epidemic characteristics have been obtained. In particular, for Ebola the basic reproduction numbers are 1.3522 (95% CI (1.3506, 1.3537, 1.2101 (95% CI (1.2084, 1.2119, 3.0234 (95% CI (2.6063, 3.4881, and 1.9018 (95% CI (1.8565, 1.9478, the turning points are November 7,November 17, October 2, and November 3, 2014, and the final sizes until December 2015 are 25794 (95% CI (25630, 25958, 3916 (95% CI (3865, 3967, 9886 (95% CI (9740, 10031, and 12633 (95% CI (12515, 12750 for West Africa, Guinea, Liberia, and Sierra Leone, respectively. The main results confirm that model selection is crucial in evaluating and predicting the important quantities describing the emerging infectious diseases, and arbitrarily picking a model without any consideration of alternatives is problematic.

  19. Comparison and clinical utility evaluation of four multiple allergen simultaneous tests including two newly introduced fully automated analyzers

    Directory of Open Access Journals (Sweden)

    John Hoon Rim

    2016-04-01

    Full Text Available Background: We compared the diagnostic performances of two newly introduced fully automated multiple allergen simultaneous tests (MAST analyzers with two conventional MAST assays. Methods: The serum samples from a total of 53 and 104 patients were tested for food panels and inhalant panels, respectively, in four analyzers including AdvanSure AlloScreen (LG Life Science, Korea, AdvanSure Allostation Smart II (LG Life Science, PROTIA Allergy-Q (ProteomeTech, Korea, and RIDA Allergy Screen (R-Biopharm, Germany. We compared not only the total agreement percentages but also positive propensities among four analyzers. Results: Evaluation of AdvanSure Allostation Smart II as upgraded version of AdvanSure AlloScreen revealed good concordance with total agreement percentages of 93.0% and 92.2% in food and inhalant panel, respectively. Comparisons of AdvanSure Allostation Smart II or PROTIA Allergy-Q with RIDA Allergy Screen also showed good concordance performance with positive propensities of two new analyzers for common allergens (Dermatophagoides farina and Dermatophagoides pteronyssinus. The changes of cut-off level resulted in various total agreement percentage fluctuations among allergens by different analyzers, although current cut-off level of class 2 appeared to be generally suitable. Conclusions: AdvanSure Allostation Smart II and PROTIA Allergy-Q presented favorable agreement performances with RIDA Allergy Screen, although positive propensities were noticed in common allergens. Keywords: Multiple allergen simultaneous test, Automated analyzer

  20. Evaluation of a novel educational strategy, including inhaler-based reminder labels, to improve asthma inhaler technique.

    Science.gov (United States)

    Basheti, Iman A; Armour, Carol L; Bosnic-Anticevich, Sinthia Z; Reddel, Helen K

    2008-07-01

    To evaluate the feasibility, acceptability and effectiveness of a brief intervention about inhaler technique, delivered by community pharmacists to asthma patients. Thirty-one pharmacists received brief workshop education (Active: n=16, CONTROL: n=15). Active Group pharmacists were trained to assess and teach dry powder inhaler technique, using patient-centered educational tools including novel Inhaler Technique Labels. Interventions were delivered to patients at four visits over 6 months. At baseline, patients (Active: 53, CONTROL: 44) demonstrated poor inhaler technique (mean+/-S.D. score out of 9, 5.7+/-1.6). At 6 months, improvement in inhaler technique score was significantly greater in Active cf. CONTROL patients (2.8+/-1.6 cf. 0.9+/-1.4, p<0.001), and asthma severity was significantly improved (p=0.015). Qualitative responses from patients and pharmacists indicated a high level of satisfaction with the intervention and educational tools, both for their effectiveness and for their impact on the patient-pharmacist relationship. A simple feasible intervention in community pharmacies, incorporating daily reminders via Inhaler Technique Labels on inhalers, can lead to improvement in inhaler technique and asthma outcomes. Brief training modules and simple educational tools, such as Inhaler Technique Labels, can provide a low-cost and sustainable way of changing patient behavior in asthma, using community pharmacists as educators.

  1. Performance evaluation of alternative fuel/engine concepts 1990- 1995. Final report including addendum of diesel vehicles

    Energy Technology Data Exchange (ETDEWEB)

    Nylund, N.O.; Ikonen, M.; Kytoe, M.; Lappi, M.; Westerholm, M.; Laurikko, J. [VTT Energy, Espoo (Finland). Energy Use

    1996-12-31

    Annex V within the IEA Agreement on Alternative Motor Fuels is the first subtask to generate new experimental data. The objective of the task is to generate information on the emission potential of alternative fuels in severe operating conditions and to evaluate new emission measurement methods. The work was carried out in three phases, Engine Tests, Vehicle Tests and Addendum of Diesel Vehicles. The work was carried out at VTT (Technical Research Centre of Finland) as a cost shared operation. Participants were Belgium (Parts Two and Three), Canada (Parts One and Two), Finland, Italy (Part One), Japan, the Netherlands Sweden and USA. The United Kingdom also joined at the end of the Annex. The work included 143 different vehicle/fuel/temperature combinations. FTP type emission tests were run on 14 vehicles powered with different gasoline compositions, methanol (M50 and M85), ethanol (E85), LPG, CNG and diesel. Both regulated and unregulated emission components were measured using the most up-to-date emissions measurement technology. The results indicated, that today`s advanced gasoline vehicles must be considered rather clean. Diesel is comparable with gasoline in the case of CO and HC. M85 gives low emissions in warm conditions, but unburned methanol must be controlled. Natural gas and LPG are inherently clean fuels which, using up-to-date engine technology, give low emissions in all conditions. (orig.) (29 refs.)

  2. Cross-cultural evaluations of avatar facial expressions designed by Western and Japanese Designers

    DEFF Research Database (Denmark)

    Koda, Tomoko; Rehm, Matthias; André, Elisabeth

    2008-01-01

    The goal of the study is to investigate cultural differences in avatar expression evaluation and apply findings from psychological study in human facial expression recognition. Our previous study using Japanese designed avatars showed there are cultural differences in interpreting avatar facial...... expressions, and the psychological theory that suggests physical proximity affects facial expression recognition accuracy is also applicable to avatar facial expressions. This paper summarizes the early results of the successive experiment that uses western designed avatars. We observed tendencies of cultural...

  3. A Design Study of the Inflated Sphere Landing Vehicle, Including the Landing Performance and the Effects of Deviations from Design Conditions

    Science.gov (United States)

    Martin, E. Dale

    1961-01-01

    The impact motion of the inflated sphere landing vehicle with a payload centrally supported from the spherical skin by numerous cords has been determined on the assumption of uniform isentropic gas compression during impact. The landing capabilities are determined for a system containing suspension cords of constant cross section. The effects of deviations in impact velocity and initial gas temperature from the design conditions are studied. Also discussed are the effects of errors in the time at which the skin is ruptured. These studies indicate how the design parameters should be chosen to insure reliability of the landing system. Calculations have been made and results are presented for a sphere inflated with hydrogen, landing on the moon in the absence of an atmosphere. The results are presented for one value of the skin-strength parameter.

  4. Design and Operation of the Transformed National Healthy Start Evaluation.

    Science.gov (United States)

    Banks, Jamelle E; Dwyer, Maura; Hirai, Ashley; Ghandour, Reem M; Atrash, Hani K

    2017-12-01

    Purpose Improving pregnancy outcomes for women and children is one of the nation's top priorities. The Healthy Start (HS) program was created to address factors that contribute to high infant mortality rates (IMRs) and persistent disparities in IMRs. The program began in 1991 and was transformed in 2014 to apply lessons from emerging research, past evaluation findings, and expert recommendations. To understand the implementation and impact of the transformed program, there is a need for a robust and comprehensive evaluation. Description The national HS evaluation will include an implementation evaluation, which will describe program components that affect outcomes; a utilization evaluation, which will examine the characteristics of women and infants who did and did not utilize the program; and an outcome evaluation, which will assess the program's effectiveness with regard to producing expected outcomes among the target population. Data sources include the National HS Program Survey, a HS participant survey, and individual-level program data linked to vital records and the Pregnancy Risk Assessment Monitoring System (PRAMS) survey. Assessment Descriptive analyses will be used to examine differences in risk profiles between participants and non-participants, as well as to calculate penetration rates for high-risk women in respective service areas. Multivariable analyses will be used to determine the impact of the program on key outcomes and will explore variation by dose, type of services received, and grantee characteristics. Conclusion Evaluation findings are expected to inform program decisions and direction, including identification of effective program components that can be spread and scaled.

  5. Evaluation of materials and design modifications for aircraft brakes

    Science.gov (United States)

    Ho, T. L.; Kennedy, F. E.; Peterson, M. B.

    1975-01-01

    A test program is described which was carried out to evaluate several proposed design modifications and several high-temperature friction materials for use in aircraft disk brakes. The evaluation program was carried out on a specially built test apparatus utilizing a disk brake and wheel half from a small het aircraft. The apparatus enabled control of brake pressure, velocity, and braking time. Tests were run under both constant and variable velocity conditions and covered a kinetic energy range similar to that encountered in aircraft brake service. The results of the design evaluation program showed that some improvement in brake performance can be realized by making design changes in the components of the brake containing friction material. The materials evaluation showed that two friction materials show potential for use in aircraft disk brakes. One of the materials is a nickel-based sintered composite, while the other is a molybdenum-based material. Both materials show much lower wear rates than conventional copper-based materials and are better able to withstand the high temperatures encountered during braking. Additional materials improvement is necessary since both materials show a significant negative slope of the friction-velocity curve at low velocities.

  6. Design and Evaluation Methods for Underwater Control Systems

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Lin

    1996-12-31

    This thesis on underwater control systems is written with the designer in mind, assuming that the reader has some knowledge of control theory. It can be used as a text for undergraduate students and engineers. To help readers better understand the system they will be working with, the thesis is organised in a stepwise way. The reader will gain basic knowledge about underwater operations, equipment and control systems. Then the reader will be able to follow the steps to develop a required control system for an underwater equipment by first understanding the characteristics of the design problem, customer requirement, functional requirement, and possible solution, and then to present a mathematical model of the control problem. Having developed the concept, the thesis guides the reader to develop evaluation criteria and different ways to make the decision. The thesis gives an overview of how to achieve a successful design rather than giving the techniques for detailed control system design. Chapter 1 describes underwater operations and systems. Chapter 2 discusses issues of underwater control systems and control methods. Chapter 3 deals with design method and control systems theory, focusing on human-centered control. Chapter 4 discusses methods used to evaluate and rank products, and chapter 5 applies the methods to an example. 113 refs., 115 figs., 80 tabs.

  7. Design and Evaluation Methods for Underwater Control Systems

    Energy Technology Data Exchange (ETDEWEB)

    Chi, Lin

    1997-12-31

    This thesis on underwater control systems is written with the designer in mind, assuming that the reader has some knowledge of control theory. It can be used as a text for undergraduate students and engineers. To help readers better understand the system they will be working with, the thesis is organised in a stepwise way. The reader will gain basic knowledge about underwater operations, equipment and control systems. Then the reader will be able to follow the steps to develop a required control system for an underwater equipment by first understanding the characteristics of the design problem, customer requirement, functional requirement, and possible solution, and then to present a mathematical model of the control problem. Having developed the concept, the thesis guides the reader to develop evaluation criteria and different ways to make the decision. The thesis gives an overview of how to achieve a successful design rather than giving the techniques for detailed control system design. Chapter 1 describes underwater operations and systems. Chapter 2 discusses issues of underwater control systems and control methods. Chapter 3 deals with design method and control systems theory, focusing on human-centered control. Chapter 4 discusses methods used to evaluate and rank products, and chapter 5 applies the methods to an example. 113 refs., 115 figs., 80 tabs.

  8. A New Physical Protection System Design and Evaluation Process

    Energy Technology Data Exchange (ETDEWEB)

    Lim, Heoksoon; Kim, Myungsu; Bae, Yeongkyoung; Na, Janghwan [KHNP-CRI, Daejeon (Korea, Republic of)

    2014-10-15

    International Atomic Energy Agency(IAEA) had established security-related department and has been strengthening security measures against possible sabotage. IAEA enforces the recommendations for the physical protection of NPPs in the INFCIRC/ 225/Rev.5 to the member states and U.S. NRC also enforces the similar requirements in 10 CFR 73.55. Thus, in order to let Korean NPPs meet the new requirements in INFCIRC/225/Rev.5 or U.S. NRC requirements, Korea nuclear licensee should develop or establish appropriate physical protection system (PPS) design methods for the physical protection of the operating NPPs and new NPPs. KHNP is doing the project of 'Development of APR1400 Physical Protection System Design (2012- 2015, KHNP/KAERI /KEPCO E-C)'. This paper describes overview of a physical protection system (PPS) design and evaluation for an advanced nuclear power plant. It found that a new physical protection system (PPS)design and evaluation. KHNP is doing the project of Physical Protection System design according to U.S. NRC requirements and IAEA requirements in INFCIRC /225 /Rev.5 and will complete by 7.31, 2015 for development of APR1400 Physical Protection System. After completing this project, the results of project are expected to apply new NPPs.

  9. Ergonomic design and evaluation of a diagnostic ultrasound transducer holder.

    Science.gov (United States)

    Ghasemi, Mohamad Sadegh; Hosseinzadeh, Payam; Zamani, Farhad; Ahmadpoor, Hossein; Dehghan, Naser

    2017-12-01

    Work-related musculoskeletal disorders (WMSDs) are injuries and disorders that affect the body's movement and musculoskeletal system. Awkward postures represent one of the major ergonomic risk factors that cause WMSDs among sonographers while working with an ultrasound transducer. This study aimed to design and evaluate a new holder for the ultrasound transducer. In the first phase a new holder was designed for the transducer, considering design principles. Evaluation of the new holder was then carried out by electrogoniometry and a locally perceived discomfort (LPD) scale. The application of design principles to the new holder resulted in an improvement of wrist posture and comfort. Wrist angles in extension, flexion, radial deviation and ulnar deviation were lower with utilization of the new holder. The severity of discomfort based on the LPD method in the two modes of work with and without the new holder was reported with values of 1.3 and 1.8, respectively (p ergonomics design principles was effective in minimizing wrist deviation and increasing comfort while working with the new holder.

  10. Design and Evaluation of Human System Interfaces (HSIs)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    In the safe operation of nuclear power plants and other complex process industries the performance of the control room crews plays an important role. In this respect a well-functioning and well-designed Human-System Interface (HSI) is crucial for safe and efficient operation of the plant. It is therefore essential that the design, development and evaluation of both control rooms and HSI-solutions are conducted in a well-structured way, applying sound human factors principles and guidelines in all phases of the HSI development process. Many nuclear power plants around the world are currently facing major modernisation of their control rooms. In this process computerised, screen-based HSIs replace old conventional operator interfaces. In new control rooms, both in the nuclear field and in other process industries, fully digital, screen-based control rooms are becoming the standard. It is therefore of particular importance to address the design and evaluation of screen-based HSIs in a systematic and consistent way in order to arrive at solutions which take proper advantage of the possibilities for improving operator support through the use of digital, screen-based HSIs, at the same time avoiding pitfalls and problems in the use of this technology. The Halden Reactor Project, in cooperation with the OECD Nuclear Energy Agency, organised an International Summer School on ''Design and Evaluation of Human-System Interfaces (HSIs)'' in Halden, Norway in the period August 25th - 29th, 2003. The Summer School addressed the different steps in design, development and evaluation of HSIs, and the human factors principles, standards and guidelines which should be followed in this process. The lectures comprised both theoretical background, as well as examples of good and bad HSI design, thereby providing practical advice in design and evaluation of operator interfaces and control room solutions to the participants in the Summer School. This CD contains the

  11. Design and Evaluation of Human System Interfaces (HSIs)

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2003-07-01

    In the safe operation of nuclear power plants and other complex process industries the performance of the control room crews plays an important role. In this respect a well-functioning and well-designed Human-System Interface (HSI) is crucial for safe and efficient operation of the plant. It is therefore essential that the design, development and evaluation of both control rooms and HSI-solutions are conducted in a well-structured way, applying sound human factors principles and guidelines in all phases of the HSI development process. Many nuclear power plants around the world are currently facing major modernisation of their control rooms. In this process computerised, screen-based HSIs replace old conventional operator interfaces. In new control rooms, both in the nuclear field and in other process industries, fully digital, screen-based control rooms are becoming the standard. It is therefore of particular importance to address the design and evaluation of screen-based HSIs in a systematic and consistent way in order to arrive at solutions which take proper advantage of the possibilities for improving operator support through the use of digital, screen-based HSIs, at the same time avoiding pitfalls and problems in the use of this technology. The Halden Reactor Project, in cooperation with the OECD Nuclear Energy Agency, organised an International Summer School on ''Design and Evaluation of Human-System Interfaces (HSIs)'' in Halden, Norway in the period August 25th - 29th, 2003. The Summer School addressed the different steps in design, development and evaluation of HSIs, and the human factors principles, standards and guidelines which should be followed in this process. The lectures comprised both theoretical background, as well as examples of good and bad HSI design, thereby providing practical advice in design and evaluation of operator interfaces and control room solutions to the participants in the Summer School. This CD contains the Proceedings of the

  12. Design and Evaluation of Human System Interfaces (HSIs)

    International Nuclear Information System (INIS)

    2003-01-01

    In the safe operation of nuclear power plants and other complex process industries the performance of the control room crews plays an important role. In this respect a well-functioning and well-designed Human-System Interface (HSI) is crucial for safe and efficient operation of the plant. It is therefore essential that the design, development and evaluation of both control rooms and HSI-solutions are conducted in a well-structured way, applying sound human factors principles and guidelines in all phases of the HSI development process. Many nuclear power plants around the world are currently facing major modernisation of their control rooms. In this process computerised, screen-based HSIs replace old conventional operator interfaces. In new control rooms, both in the nuclear field and in other process industries, fully digital, screen-based control rooms are becoming the standard. It is therefore of particular importance to address the design and evaluation of screen-based HSIs in a systematic and consistent way in order to arrive at solutions which take proper advantage of the possibilities for improving operator support through the use of digital, screen-based HSIs, at the same time avoiding pitfalls and problems in the use of this technology. The Halden Reactor Project, in cooperation with the OECD Nuclear Energy Agency, organised an International Summer School on ''Design and Evaluation of Human-System Interfaces (HSIs)'' in Halden, Norway in the period August 25th - 29th, 2003. The Summer School addressed the different steps in design, development and evaluation of HSIs, and the human factors principles, standards and guidelines which should be followed in this process. The lectures comprised both theoretical background, as well as examples of good and bad HSI design, thereby providing practical advice in design and evaluation of operator interfaces and control room solutions to the participants in the Summer School. This CD contains the Proceedings of the

  13. Designing and Evaluating Conative Game-Based Learning Scenarios

    DEFF Research Database (Denmark)

    Schønau-Fog, Henrik

    2014-01-01

    It is an essential prerequisite to design for motivation in game-based learning applications, tools and activities. However, how is it possible to design and evaluate motivational game-based learning scenarios in a systematic process-oriented manner based on conation and player engagement? While...... of ‘continuation desire’ such as interfacing with the scenario, exploration and socialising. This paper aims to combine the concepts of Player Engagement, Conation and Continuation Desire by focusing on the conative aspects which are the essential drivers for the desire to continue any learning activity......-based learning scenarios....

  14. Design synthesis and biological evaluation of 2-methylphenyl semicarbazone derivatives

    Directory of Open Access Journals (Sweden)

    Manmohan Singhal

    2011-03-01

    Full Text Available We have used pharmacophore hybridization technique of drug design and designed a pharmacophore model 2-methylphenylsemicarbazone which is having hydrogen acceptor site, hydrogen donor site, lipophilic site etc using ligandscout-2.02 software. A series of 2-methylphenyl-semicarbazone was synthesized and evaluated for their antipyretic activity using boiled cow milk induced pyrexia in rabbits. Compound 11 was the most active compound. The possible metabolites of some selected synthesized chalconesemicarbazones were predicted by computational method using Pallas version-3.1 ADME-Tox prediction software. The major pathway of metabolism was found to be p-hydroxylation and amide hydrolysis.

  15. All this grassroots, real life knowledge: Comparing perceived with realised concerns of including non-academic evaluators in societal impact assessment

    Energy Technology Data Exchange (ETDEWEB)

    Derrick, G.E.; Samuel, G.S.

    2016-07-01

    New research assessment frameworks that include societal impact criteria, also require the inclusion on non-academic evaluators (users) as part of the assessment panels. Little research has been conducted on how these user evaluators are received by traditionally academic-led panels, and how their presence influences evaluation outcomes. This is especially the case for evaluations including societal impact criteria. This article uses a mixed-methods approach to explore academic-evaluator concerns about the inclusion of user-evaluators in the assessment process. In addition, it explores how their involvement, influenced the outcomes of the evaluation process. (Author)

  16. Societal risk approach to safeguards design and evaluation

    International Nuclear Information System (INIS)

    Murphey, W.M.; Sherr, T.S.; Bennett, C.A.

    1975-01-01

    A comprehensive rationale for safeguards design and evaluation, and a framework for continuing systematic assessment of the system's effectiveness and efficient allocation of available safeguards resources for balanced protection, were developed. The societal risk approach employed considers the likelihood of successful destructive acts involving nuclear materials or facilities and the magnitude of the effects on society. The safeguards problem is described in terms of events affecting societal risk and adversary actions. Structure of the safeguards system and the evaluation of its adequacy are discussed. Adversary characteristics are also discussed

  17. An Evaluation of Alternative Designs for a Grid Information Service

    Science.gov (United States)

    Smith, Warren; Waheed, Abdul; Meyers, David; Yan, Jerry; Kwak, Dochan (Technical Monitor)

    2001-01-01

    The Globus information service wasn't working well. There were many updates of data from Globus daemons which saturated the single server and users couldn't retrieve information. We created a second server for NASA and Alliance. Things were great on that server, but a bit slow on the other server. We needed to know exactly how the information service was being used. What were the best servers and configurations? This viewgraph presentation gives an overview of the evaluation of alternative designs for a Grid Information Service. Details are given on the workload characterization, methodology used, and the performance evaluation.

  18. Evaluation of Market Design Agents: The Mertacor Perspective

    Science.gov (United States)

    Stavrogiannis, Lampros C.; Mitkas, Pericles A.

    The annual Trading Agent Competition for Market Design, CAT, provides a testbed to study the mechanisms that modern stock exchanges use in their effort to attract potential traders while maximizing their profit. This paper presents an evaluation of the agents that participated in the 2008 competition. The evaluation is based on the analysis of the CAT finals as well as on the results obtained from post-tournament experiments. We present Mertacor, our entrant for 2008, and compare it with the other available agents. In addition, we introduce a simple yet effective way of computing the global competitive equilibrium that Mertacor utilizes and discuss its importance for the game.

  19. Design and evaluation of materials for space reactors

    International Nuclear Information System (INIS)

    Tavassoli, A.A.; Vrillon, B.; Robert, G.

    1990-01-01

    The French programme envisages a 20 kWe reactor, project ERATO, with three technological options. The first option is a sodium cooled reactor, derived from the fast breeder reactor technology, (upper core outlet temperature of 700 0 C). The second option is based on the High Temperature Gas-cooled Reactor technology (outlet temperature range 700 0 C-900 0 C). The third option is the reference solution, lithium cooled and UN fuelled fast spectrum reactor, (outlet temperature as high as 1200 0 C). The choice is essentially dominated by material considerations, and more specifically by the problems related to the compatibility with the cooling medium and to the high temperature creep resistance. For the first system limited work will be needed as the technology used is well experimented and there is a wealth of information on the austenitic stainless steel Type 316L-SPH. For the second system, most of the work has been concentrated on characterization of existing commercial alloys. This has included the preselection and the testing of a number of superalloys irradiated or not. The results obtained from high temperature tensile and creep tests have allowed selection of Haynes 230 as the primary candidate material and have also permitted calculation of allowable design stresses for this alloy. For the very high temperature system the French R and D programme has focused on Mo-Re alloys. The results obtained to this date from microstructural examinations and mechanical tests performed on different alloy compositions have allowed selection of Mo-25%Re for future optimization work. They have also shown the need for evaluation of creep properties at low stresses where microstructural instabilities are likely to occur as a result of long exposure to high temperature

  20. 36 CFR 1193.23 - Product design, development, and evaluation.

    Science.gov (United States)

    2010-07-01

    ... following factors, as the manufacturer deems appropriate: (1) Where market research is undertaken, including individuals with disabilities in target populations of such research; (2) Where product design, testing, pilot... to validate any unproven access solutions through testing with individuals with disabilities or with...

  1. 47 CFR 6.7 - Product design, development, and evaluation.

    Science.gov (United States)

    2010-10-01

    ... factors, as the manufacturer deems appropriate: (1) Where market research is undertaken, including individuals with disabilities in target populations of such research; (2) Where product design, testing, pilot... to validate any unproven access solutions through testing with individuals with disabilities or with...

  2. Statistical evaluation of design-error related accidents

    International Nuclear Information System (INIS)

    Ott, K.O.; Marchaterre, J.F.

    1980-01-01

    In a recently published paper (Campbell and Ott, 1979), a general methodology was proposed for the statistical evaluation of design-error related accidents. The evaluation aims at an estimate of the combined residual frequency of yet unknown types of accidents lurking in a certain technological system. Here, the original methodology is extended, as to apply to a variety of systems that evolves during the development of large-scale technologies. A special categorization of incidents and accidents is introduced to define the events that should be jointly analyzed. The resulting formalism is applied to the development of the nuclear power reactor technology, considering serious accidents that involve in the accident-progression a particular design inadequacy

  3. New Discrete Fibonacci Charge Pump Design, Evaluation and Measurement

    Directory of Open Access Journals (Sweden)

    Matoušek David

    2017-06-01

    Full Text Available This paper focuses on the practical aspects of the realisation of Dickson and Fibonacci charge pumps. Standard Dickson charge pump circuit solution and new Fibonacci charge pump implementation are compared. Both charge pumps were designed and then evaluated by LTspice XVII simulations and realised in a discrete form on printed circuit board (PCB. Finally, the key parameters as the output voltage, efficiency, rise time, variable power supply and clock frequency effects were measured.

  4. New Discrete Fibonacci Charge Pump Design, Evaluation and Measurement

    Science.gov (United States)

    Matoušek, David; Hospodka, Jiří; Šubrt, Ondřej

    2017-06-01

    This paper focuses on the practical aspects of the realisation of Dickson and Fibonacci charge pumps. Standard Dickson charge pump circuit solution and new Fibonacci charge pump implementation are compared. Both charge pumps were designed and then evaluated by LTspice XVII simulations and realised in a discrete form on printed circuit board (PCB). Finally, the key parameters as the output voltage, efficiency, rise time, variable power supply and clock frequency effects were measured.

  5. The conceptual design and economic evaluation of utility scale SMES

    International Nuclear Information System (INIS)

    Masuda, M.

    1986-01-01

    The paper reports the result of current Japanese activities in designing and evaluating the economic feasibility of utility Superconducting Magnetic Energy Storage (SMES). The 5 GWh/1 GW is proposed as a relevant unit of SMES in the year 2000. More than 20 companies, several universities and two national laboratories joined in a task force to study this technology. After three year's assessment, the conclusion on utility scale SMES is that no unresolvable technologies have been found and commercialization potential exists

  6. Web-Based Museum Trails on PDAs for University-Level Design Students: Design and Evaluation

    Science.gov (United States)

    Reynolds, R.; Walker, K.; Speight, C.

    2010-01-01

    This paper describes the development and evaluation of web-based museum trails for university-level design students to access on handheld devices in the Victoria and Albert Museum (V&A) in London. The trails offered students a range of ways of exploring the museum environment and collections, some encouraging students to interpret objects and…

  7. Participatory ergonomics for psychological factors evaluation in work system design.

    Science.gov (United States)

    Wang, Lingyan; Lau, Henry Y K

    2012-01-01

    It is a well recognized understanding that workers whose voice needs to be heard should be actively encouraged as full participants and involved in the early design stages of new ergonomic work system which encompass the development and implementation of new tools, workplaces, technologies or organizations. This paper presents a novel participatory strategy to evaluate three key psychological factors which are respectively mental fatigue, spiritual stress, and emotional satisfaction in work system design based on a modified version of Participatory Ergonomics (PE). In specific, it integrates a PE technique with a formulation view by combining the parallel development of PE strategies, frameworks and functions throughout the coverage of the entire work system design process, so as to bridge the gap between qualitative and quantitative analysis of psychological factors which can cause adverse or advantageous effects on worker's physiological and behavioral performance.

  8. Evaluating public awareness of new currency design features

    Science.gov (United States)

    DiNunzio, Lisa; Church, Sara E.

    2002-04-01

    One of the goals of the 1996 series design was to integrate highly recognizable features that enable the general public to more easily distinguish counterfeit from genuine notes, thereby reducing the chance of counterfeit notes being passed. The purpose of this study is to evaluate how knowledgeable the public is concerning the new currency, to identify the channels through which the public learns about new currency design, and to assess the usefulness of the new currency's authentication features. Also, the study will serve as a baseline measurement for future design studies and in comparative analysis with other countries. The results of the qualitative research will be described in the following sections of this paper. The quantitative research is scheduled to begin in February 2002, at the same time as the Netherlands' opinion poll of the Euro and NLG-notes in an effort to compare results.

  9. Evaluation of seismic criteria used in design of INEL facilities

    International Nuclear Information System (INIS)

    Young, G.A.

    1977-01-01

    This report provides the results of an independent evaluation of seismic studies that were made to establish the seismic acceleration levels and the response spectra used in the design of vital facilities at Idaho National Engineering Laboratory. A comparison of the procedures used to define the seismic acceleration values and response spectra at INEL with the requirements of the Nuclear Regulatory Commission showed that additional geologic studies would probably be required in order to fulfill NRC regulations. Recommendations are made on justifiable changes in the acceleration values and response spectra used at INEL. The geologic, geophysical, and seismological studies needed to provide a better understanding of the tectonic processes in the Snake River plains and the surrounding region are identified. Both potential and historical acceleration values are evaluated on a probability basis to permit a risk assessment approach to the design of new facilities and facility modifications. Studies conducted to develop seismic criteria for the design of the Loss of Fluid Test reactor and the New Waste Calcining Facility were selected as typical examples of criteria development previously used in the design of INEL facilities

  10. Design and Evaluation of Photo-Induced Biofeedback Fabric for the Enhancement in Sleeping Sense

    OpenAIRE

    Chu, Wei-Cheng; Lin, Hsin-Ju; Chiu, Shu-Ping

    2013-01-01

    Based on overcoming the sleeping obstacle for people, the purpose of this study is to design a photo-induced biofeedback fabric which is a kind of optical fiber fabric with the function of enhancing sleeping sense and to evaluate its effect. The fabrics with two layers including background layer and pattern layer were designed firstly. The pattern layers with 3 kinds of wavelengths of sine waves and the light controller with 3 kinds of flashing frequencies were then prepared. Guiding the ligh...

  11. Large scale solar district heating. Evaluation, modelling and designing

    Energy Technology Data Exchange (ETDEWEB)

    Heller, A.

    2000-07-01

    The main objective of the research was to evaluate large-scale solar heating connected to district heating (CSDHP), to build up a simulation tool and to demonstrate the application of the tool for design studies and on a local energy planning case. The evaluation of the central solar heating technology is based on measurements on the case plant in Marstal, Denmark, and on published and unpublished data for other, mainly Danish, CSDHP plants. Evaluations on the thermal, economical and environmental performances are reported, based on the experiences from the last decade. The measurements from the Marstal case are analysed, experiences extracted and minor improvements to the plant design proposed. For the detailed designing and energy planning of CSDHPs, a computer simulation model is developed and validated on the measurements from the Marstal case. The final model is then generalised to a 'generic' model for CSDHPs in general. The meteorological reference data, Danish Reference Year, is applied to find the mean performance for the plant designs. To find the expectable variety of the thermal performance of such plants, a method is proposed where data from a year with poor solar irradiation and a year with strong solar irradiation are applied. Equipped with a simulation tool design studies are carried out spreading from parameter analysis over energy planning for a new settlement to a proposal for the combination of plane solar collectors with high performance solar collectors, exemplified by a trough solar collector. The methodology of utilising computer simulation proved to be a cheap and relevant tool in the design of future solar heating plants. The thesis also exposed the demand for developing computer models for the more advanced solar collector designs and especially for the control operation of CSHPs. In the final chapter the CSHP technology is put into perspective with respect to other possible technologies to find the relevance of the application

  12. Engineering design evaluation of Atlas tile-calorimeter

    International Nuclear Information System (INIS)

    Hill, N.; Guarino, V.; Proudfoot, J.; Stanek, R.; Price, L.; Petereit, E.

    1994-01-01

    In an effort to familiarize themselves with the work that has been done to date on the design of the Tile Cal hadron calorimeter for Atlas, the authors have undertaken a thorough examination of the current designs. They concentrated on the work that has been done by the IHEP Group at Protvino, and in particular the work presented at the last Atlas Week. They constructed six different finite element models as they have learned more about the system. These models were meant to be rough models only and do not represent actual construction in all cases. In some cases, shortcuts were taken in an attempt to set boundary conditions and to reduce the size of the problem to accommodate software limitations, while still providing enough information to further the understanding of the design. After reviewing the analysis and thinking about the construction, the authors have some suggested modifications, which are presented in this paper. It is clear that the work done at both CERN and Protvino has been impressive and thorough. The authors have tried to evaluate and understand both the CERN baseline design and the suggested design option from Protvino

  13. Procedure for seismic evaluation and design of small bore piping

    International Nuclear Information System (INIS)

    Bilanin, W.; Sills, S.

    1991-01-01

    Simplified methods for the seismic design of small bore piping in nuclear power plants have teen used for many years. Various number of designers have developed unique methods to treat the large number of class 2 and 3 small bore piping systems. This practice has led to a proliferation of methods which are not standardized in the industry. These methods are generally based on enveloping the results of rigorous dynamic or conservative static analysis and result in an excessive number of supports and unrealistically high support loadings. Experience and test data have become available which warranted taking another look at the present methods for analysis of small bore piping. A recently completed Electric Power Research Institute and NCIG (a utility group) activity developed a new procedure for the seismic design and evaluation of small bore piping which provides significant safety and cost benefits. The procedure streamlines the approach to inertial stresses, which is the main feature that achieves the new benefits. Criteria in the procedure for seismic anchor movement and support design are based analysis and focus the designer on credible failure mechanisms. A walkdown of the as-constructed piping system to identify and eliminate undesirable piping features such as adverse spatial interaction is required

  14. Safety evaluation report related to the preliminary design of the Standard Reference System, RESAR-414

    International Nuclear Information System (INIS)

    1978-11-01

    The safety evaluation for the Westinghouse Standard Reactor includes information on general reactor characteristics; design criteria for systems and components; reactor coolant system; engineered safety systems; instrumentation and controls; electric power systems; auxiliary systems; steam and power conversion system; radioactive waste management; radiation protection; conduct of operations; accident analyses; and quality assurance

  15. Logic Models for Program Design, Implementation, and Evaluation: Workshop Toolkit. REL 2015-057

    Science.gov (United States)

    Shakman, Karen; Rodriguez, Sheila M.

    2015-01-01

    The Logic Model Workshop Toolkit is designed to help practitioners learn the purpose of logic models, the different elements of a logic model, and the appropriate steps for developing and using a logic model for program evaluation. Topics covered in the sessions include an overview of logic models, the elements of a logic model, an introduction to…

  16. Evaluation of Mathematical Game Design Skills of Pre-Service Classroom Teachers

    Science.gov (United States)

    Pilten, Pusat; Pilten, Gülhiz; Divrik, Ramazan; Divrik, Fatma

    2017-01-01

    The purpose of the research is to evaluate the games prepared by pre-service classroom teachers within the scope of "Mathematics Teaching 1" and "Mathematics Teaching 2" courses, which are included in the undergraduate classroom teaching programs in Turkey, and to make predictions on the game design skills of pre-service…

  17. Design evaluation on sodium piping system and comparison of the design codes

    International Nuclear Information System (INIS)

    Lee, Dong Won; Jeong, Ji Young; Lee, Yong Bum; Lee, Hyeong Yeon

    2015-01-01

    A large-scale sodium test loop of STELLA-1 (Sodium integral effect test loop for safety simulation and assessment) with two main piping systems has been installed at KAERI. In this study, design evaluations on the main sodium piping systems in STELLA-1 have been conducted according to the DBR (design by rule) codes of the ASME B31.1 and RCC-MRx RB-3600. In addition, design evaluations according to the DBA (design by analysis) code of the ASME Section III Subsection NB-3200 have been conducted. The evaluation results for the present piping systems showed that results from the DBR codes were more conservative than those from the DBA code, and among the DBR codes, the non-nuclear code of the ASME B31.1 was more conservative than the French nuclear DBR code of the RCC-MRx RB-3600. The conservatism on the DBR codes of the ASME B31.1 and RCC-MRx RB-3600 was quantified based on the present sodium piping analyses.

  18. Design evaluation on sodium piping system and comparison of the design codes

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Dong Won; Jeong, Ji Young; Lee, Yong Bum; Lee, Hyeong Yeon [KAERI, Daejeon (Korea, Republic of)

    2015-03-15

    A large-scale sodium test loop of STELLA-1 (Sodium integral effect test loop for safety simulation and assessment) with two main piping systems has been installed at KAERI. In this study, design evaluations on the main sodium piping systems in STELLA-1 have been conducted according to the DBR (design by rule) codes of the ASME B31.1 and RCC-MRx RB-3600. In addition, design evaluations according to the DBA (design by analysis) code of the ASME Section III Subsection NB-3200 have been conducted. The evaluation results for the present piping systems showed that results from the DBR codes were more conservative than those from the DBA code, and among the DBR codes, the non-nuclear code of the ASME B31.1 was more conservative than the French nuclear DBR code of the RCC-MRx RB-3600. The conservatism on the DBR codes of the ASME B31.1 and RCC-MRx RB-3600 was quantified based on the present sodium piping analyses.

  19. Rapid Structural Design Change Evaluation with AN Experiment Based FEM

    Science.gov (United States)

    Chu, C.-H.; Trethewey, M. W.

    1998-04-01

    The work in this paper proposes a dynamic structural design model that can be developed in a rapid fashion. The approach endeavours to produce a simplified FEM developed in conjunction with an experimental modal database. The FEM is formulated directly from the geometry and connectivity used in an experimental modal test using beam/frame elements. The model sacrifices fine detail for a rapid development time. The FEM is updated at the element level so the dynamic response replicates the experimental results closely. The physical attributes of the model are retained, making it well suited to evaluate the effect of potential design changes. The capabilities are evaluated in a series of computational and laboratory tests. First, a study is performed with a simulated cantilever beam with a variable mass and stiffness distribution. The modal characteristics serve as the updating target with random noise added to simulate experimental uncertainty. A uniformly distributed FEM is developed and updated. The results show excellent results, all natural frequencies are within 0·001% with MAC values above 0·99. Next, the method is applied to predict the dynamic changes of a hardware portal frame structure for a radical design change. Natural frequency predictions from the original FEM differ by as much as almost 18% with reasonable MAC values. The results predicted from the updated model produce excellent results when compared to the actual hardware changes, the first five modal natural frequency difference is around 5% and the corresponding mode shapes producing MAC values above 0·98.

  20. Ranitidine Loaded Biopolymer Floats: Designing, Characterization, and Evaluation

    Directory of Open Access Journals (Sweden)

    Abdul Karim

    2017-01-01

    Full Text Available The float formulation is a strategy to improve the bioavailability of drugs by gastroretentive drug delivery system (GRDDS. A drug delivery model based on swellable and reswellable low density biopolymers has been designed to evaluate its drug release profile using ranitidine (RNT as a model drug and formulations have been prepared utilizing 32 factorial designs. The drug release (DR data has been subjected to various kinetic models to investigate the DR mechanism. A reduction in rate has been observed by expanding the amounts of PSG and LSG parts, while an expansion has been noted by increasing the concentration of tragacanth (TG and citric acid (CA with an increment in floating time. The stearic acid (SA has been used to decrease the lag time because a decrease in density of system was observed. The kinetic analysis showed that the optimized formulation (S4F3 followed zero-order kinetics and power law was found to be best fitted due to its minimum lag time and maximum floating ability. The resemblance of observed and predicted values indicated the validity of derived equations for evaluating the effect of independent variables while kinetic study demonstrated that the applied models are feasible for evaluating and developing float for RNT.

  1. Designing and Evaluating Interventions to Halt the Transmission of Tuberculosis.

    Science.gov (United States)

    Dowdy, David W; Grant, Alison D; Dheda, Keertan; Nardell, Edward; Fielding, Katherine; Moore, David A J

    2017-11-03

    To reduce the incidence of tuberculosis, it is insufficient to simply understand the dynamics of tuberculosis transmission. Rather, we must design and rigorously evaluate interventions to halt transmission, prioritizing those interventions most likely to achieve population-level impact. Synergy in reducing tuberculosis transmission may be attainable by combining interventions that shrink the reservoir of latent Mycobacterium tuberculosis infection (preventive therapy), shorten the time between disease onset and treatment initiation (case finding and diagnosis), and prevent transmission in key settings, such as the built environment (infection control). In evaluating efficacy and estimating population-level impact, cluster-randomized trials and mechanistic models play particularly prominent roles. Historical and contemporary evidence suggests that effective public health interventions can halt tuberculosis transmission, but an evidence-based approach based on knowledge of local epidemiology is necessary for success. We provide a roadmap for designing, evaluating, and modeling interventions to interrupt the process of transmission that fuels a diverse array of tuberculosis epidemics worldwide. © The Author 2017. Published by Oxford University Press for the Infectious Diseases Society of America.

  2. Detailed evaluation of ET-RR-2 neutronic design: approach to criticality

    International Nuclear Information System (INIS)

    Ashoub, N.; Amin, E.

    2000-01-01

    The ET-RR-2 safety analysis evaluation effort included the assessment of the reactor core nuclear design parameters. The present work complements the previous effort of neutronic calculations using NCNSRC computer code packages. This paper is the first in comprehensive neutronic calculation assessment up to the equilibrium core. It deals with evaluation of neutronic calculation submitted during the early phase of the licensing process; namely the proposal to assemble the first critical core, calculation of power peaking factor and determination of detailed energy group flux distribution in the core particularly in the cobalt irradiation position. The neutronic design criteria are examined qualitatively and quantitatively in the present paper

  3. Experimental study including subjective evaluations of mixing and displacement ventilation combined with radiant floor heating/cooling system

    DEFF Research Database (Denmark)

    Krajcik, Michal; Tomasi, Roberta; Simone, Angela

    2013-01-01

    Sixteen subjects evaluated the indoor environment in four experiments with different combinations of ventilation systems and radiant heating/cooling systems. In the first two tests, the simulated residential room was equipped either by a mixing ventilation system supplying warm air for space heat...

  4. CONTRIBUTIONS TO EVALUATE DESIGN INVESTMENT IN PORTUGUESE ORANGE FROM SILVES

    Directory of Open Access Journals (Sweden)

    Filipa Pias

    2016-12-01

    Full Text Available Food reminds us every day that we are a part of nature and with our daily choices it is we who preserve or not biodiversity and species. It is we who promote or not the production of more health and fresh food. In an increasingly informed society about the benefits of having a balanced diet, meals started to be seen as tasting flavours and aromas, a moment of well-being, where the origin, production and method of preparation of agricultural products play a leading role. Because the market has changed, it is no longer anonymous it became personalized and essentially motivated by what you can enjoy, which implies a willingness to participate and build its own experience. In general, the companies believe that design collaboration is an advantage but if they do not have means of measuring design’s cost/benefit, it will not be easy to understand design as an investment that brings value to business. The purpose of this research is to draw the attention for the importance of design management, by evaluating the return of design’s investment in the Portuguese agro-food industry and by developing a model that allows them to assess the return on investment in design.

  5. Design Optimization and Evaluation of Different Wind Generator Systems

    DEFF Research Database (Denmark)

    Chen, Zhe; Li, Hui

    2008-01-01

    . In this paper, seven variable speed constant frequency (VSCF) wind generator systems are investigated, namely permanent magnet synchronous generators with the direct-driven (PMSG_DD), the single-stage gearbox (PMSG_1G) and three-stage gearbox (PMSG_3G) concepts, doubly fed induction generators with the three......With rapid development of wind power technologies and significant growth of wind power capacity installed worldwide, various wind generator systems have been developed and built. The objective of this paper is to evaluate various wind generator systems by optimization designs and comparisons......-stage gearbox (DFIG_3G) and with the single-stage gearbox (DFIG_1G), the electricity excited synchronous generator with the direct-driven (EESG_DD), and the VSCF squirrel cage induction generator with the three-stage gearbox (SCIG_3G). Firstly, the design models of wind turbines, three/single stage gearbox...

  6. Safety design and evaluation policy for future FBRs in Japan

    International Nuclear Information System (INIS)

    Aizawa, Kiyoto

    1991-01-01

    The safety policy for fast breeder reactors (FBRs) has gradually matured in accordance with the development of FBRs. The safety assessment of the Japanese prototype FBR, Monju during the licensing process accelerated the maturity and the integration of knowledge and databases. Results are expected to be reflected in the establishment of the safety design and evaluation policy for FBRs. Although the methodologies and safety policies developed for LWRs are applicable in principle to future FBRs, it is neither rational nor realistic to treat safety only with these policies. It is recommended that one should develop the methodologies and safety policies starting from understanding of the inherent safety characteristics of FBR's through safety research, plant operating experience and design work. In the last few years, some technical committees were organized in Japan and have discussed key safety issues which are specific to FBRs in order to provide preparatory reports and to establish safety standards and guidelines for future commercial FBRs. (author)

  7. Process Design and Evaluation for Chemicals Based on Renewable Resources

    DEFF Research Database (Denmark)

    Fu, Wenjing

    . In addition, another characteristic of chemicals based on renewable feedstocks is that many alternative technologies and possible routes exist, resulting in many possible process flowsheets. The challenge for process engineers is then to choose between possible process routes and alternative technologies...... development of chemicals based on renewable feedstocks. As an example, this thesis especially focuses on applying the methodology in process design and evaluation of the synthesis of 5-hydroxymethylfurfural (HMF) from the renewable feedstock glucose/fructose. The selected example is part of the chemoenzymatic......One of the key steps in process design is choosing between alternative technologies, especially for processes producing bulk and commodity chemicals. Recently, driven by the increasing oil prices and diminishing reserves, the production of bulk and commodity chemicals from renewable feedstocks has...

  8. Evaluating comfort with varying temperatures: a graphic design tool

    Energy Technology Data Exchange (ETDEWEB)

    Evans, J.M. [Research Centre Habitat and Energy, Faculty of Architecture, Design and Urbanism, University of Buenos Aires, Ciudad Universitaria (Argentina)

    2002-07-01

    This paper considers the need to define comfort of indoor and outdoor spaces in relation to the daily variations of temperature. A graphical tool is presented, which indicates the daily swings of temperature, shown as a single point on a graph representing the average temperature and the maximum temperature swing. This point can be compared with the comfort zones for different activity levels, such as sedentary activity, sleeping, indoor and outdoor circulation according to the design proposals for different spaces. The graph allows the representation of climatic variables, the definition of comfort zones, the selection of bio climatic design resources and the evaluation of indoor temperatures, measured in actual buildings or obtained from computer simulations. The development of the graph is explained and examples given with special emphasis on the use of thermal mass. (author)

  9. Using GREENSCOPE Indicators for Sustainable Computer-Aided Process Evaluation and Design

    Science.gov (United States)

    Manufacturing sustainability can be increased by educating those who design, construct, and operate facilities, and by using appropriate tools for process evaluation and design. The U.S. Environmental Protection Agency's GREENSCOPE methodology and tool, for evaluation and design ...

  10. Pharmacology Goes Concept-Based: Course Design, Implementation, and Evaluation.

    Science.gov (United States)

    Lanz, Amelia; Davis, Rebecca G

    Although concept-based curricula are frequently discussed in the nursing education literature, little information exists to guide the development of a concept-based pharmacology course. Traditionally, nursing pharmacology courses are taught with an emphasis on drug class where a prototype drug serves as an exemplar. When transitioning pharmacology to a concept-based course, special considerations are in order. How can educators successfully integrate essential pharmacological content into a curriculum structured around nursing concepts? This article presents one approach to the design and implementation of a concept-based undergraduate pharmacology course. Planning methods, supportive teaching strategies, and course evaluation procedures are discussed.

  11. Preliminary shielding design evaluation for reactor assembly of SMART

    International Nuclear Information System (INIS)

    Kim, Kyo Youn; Kang, Chang M.; Kim, Ha Yong; Zee, Sung Quun; Chang, Moon Hee

    1999-03-01

    This report describes a preliminary evaluations of SMART shielding design near the reactor core by using the DORT two-dimensional discrete ordinates transport code. The results indicate that maximum neutron fluence at the bottom of reactor vessel is 1.64x10 17 n/cm 2 and that on the radial surface of reactor vessel is 6.71x10 16 n/cm 2 . These results meet the requirement, 1.0x10 20 n/cm 2 , in 10 CFR 50.61 and the integrity of SMART reactor vessel is confirmed during the lifetime of reactor. (Author). 20 refs., 11 tabs., 8 figs

  12. The evaluation, design and construction of the uranium plant for Chemwes Limited

    International Nuclear Information System (INIS)

    Viljoen, E.B.; Bluhm, B.J.; Pilkington, W.; Taylor, J.L.; Robinson, J.E.; Le Grange, P.

    1981-01-01

    The Chemwes uranium plant was designed and constructed within fifteen months; commissioning started during June 1979, and the plant was producing at design capacity four months later. This account highlights the procedures and methods adopted to bring the plant into production. The description of the various phases includes some details of the early evaluation, and the feasibility and optimization studies; of the financing, project management, design, construction, and commissioning of the plant; and of the training of personnel. Some of the mistakes made and the factors that contributed to the success are also listed [af

  13. Global gene expression analysis for evaluation and design of biomaterials

    Directory of Open Access Journals (Sweden)

    Nobutaka Hanagata, Taro Takemura and Takashi Minowa

    2010-01-01

    Full Text Available Comprehensive gene expression analysis using DNA microarrays has become a widespread technique in molecular biological research. In the biomaterials field, it is used to evaluate the biocompatibility or cellular toxicity of metals, polymers and ceramics. Studies in this field have extracted differentially expressed genes in the context of differences in cellular responses among multiple materials. Based on these genes, the effects of materials on cells at the molecular level have been examined. Expression data ranging from several to tens of thousands of genes can be obtained from DNA microarrays. For this reason, several tens or hundreds of differentially expressed genes are often present in different materials. In this review, we outline the principles of DNA microarrays, and provide an introduction to methods of extracting information which is useful for evaluating and designing biomaterials from comprehensive gene expression data.

  14. DESIGN EVALUATIONS OF DOUBLE ROTOR SWITCHED RELUCTANCE MACHINE

    Directory of Open Access Journals (Sweden)

    C.V. ARAVIND

    2016-02-01

    Full Text Available The absence of magnets makes the reluctance machine typical for low cogging operations with the torque depending on the stator rotor interaction area. The air gap between stator pole and rotor pole gives a huge effect on the reluctance variation. The primitive double rotor switched reluctance machine lags to improvise the effect of the ripple value though the torque density is higher compared to conventional machines. An optimised circular hole position and dimensioned in the stator pole of lowers the torque ripple and reduce the acoustic noise as presented in this paper. A comparative evaluation of the conventional double rotor machine with this improved structure is done through numerical design and evaluations for the same sizing. It is found that the motor constant square density. It is found that the double rotor switched reluctance machine is improved by 140% to conventional machine.

  15. A design thinking approach to evaluating interprofessional education.

    Science.gov (United States)

    Cahn, Peter S; Bzowyckyj, Andrew; Collins, Lauren; Dow, Alan; Goodell, Kristen; Johnson, Alex F; Klocko, David; Knab, Mary; Parker, Kathryn; Reeves, Scott; Zierler, Brenda K

    2016-05-01

    The complex challenge of evaluating the impact of interprofessional education (IPE) on patient and community health outcomes is well documented. Recently, at the Radcliffe Institute for Advanced Study in the United States, leaders in health professions education met to help generate a direction for future IPE evaluation research. Participants followed the stages of design thinking, a process for human-centred problem solving, to reach consensus on recommendations. The group concluded that future studies should focus on measuring an intermediate step between learning activities and patient outcomes. Specifically, knowing how IPE-prepared students and preceptors influence the organisational culture of a clinical site as well as how the culture of clinical sites influences learners' attitudes about collaborative practice will demonstrate the value of educational interventions. With a mixed methods approach and an appreciation for context, researchers will be able to identify the factors that foster effective collaborative practice and, by extension, promote patient-centred care.

  16. Global gene expression analysis for evaluation and design of biomaterials

    International Nuclear Information System (INIS)

    Hanagata, Nobutaka; Takemura, Taro; Minowa, Takashi

    2010-01-01

    Comprehensive gene expression analysis using DNA microarrays has become a widespread technique in molecular biological research. In the biomaterials field, it is used to evaluate the biocompatibility or cellular toxicity of metals, polymers and ceramics. Studies in this field have extracted differentially expressed genes in the context of differences in cellular responses among multiple materials. Based on these genes, the effects of materials on cells at the molecular level have been examined. Expression data ranging from several to tens of thousands of genes can be obtained from DNA microarrays. For this reason, several tens or hundreds of differentially expressed genes are often present in different materials. In this review, we outline the principles of DNA microarrays, and provide an introduction to methods of extracting information which is useful for evaluating and designing biomaterials from comprehensive gene expression data. (topical review)

  17. Evaluation of 8-week body weight control program including sea tangle (Laminaria japonica) supplementation in Korean female college students

    OpenAIRE

    You, Jeong Soon; Sung, Min Jung; Chang, Kyung Ja

    2009-01-01

    This study was conducted to evaluate the effects of a body weight control program with supplementation of sea tangle (20 g/day) on 22 female college students. The contents of the program for 8 weeks contained diet therapy, exercise and behavioral modification through nutrition education. Body composition, dietary habit scores, serum lipid profiles, daily nutrient intakes and the quality of life were assessed at the beginning and at the end of the program. Average age of subjects and height we...

  18. Multinational design evaluation programme. Annual Report April 2016-April 2017

    International Nuclear Information System (INIS)

    2017-08-01

    The Multinational Design Evaluation Program (MDEP) is a multinational initiative to leverage the resources and knowledge of national regulatory authorities that are currently, or will shortly be, undertaking the review of new reactor power plant designs. MDEP was launched in 2006. In the past ten years, MDEP's reputation as an effective organisation for leveraging the resources and experiences of multiple nations in the regulatory review of new reactors has grown significantly. As a result, the portfolio of new reactor designs that are being addressed have increased from two in 2006 to five in 2017, with a possibility of adding more new reactor designs in the coming years. MDEP's membership has grown from the original 10 national regulators to 15. Over the past year, MDEP design specific working groups have all completed their common positions to address the impact of the Fukushima Daiichi nuclear power plant accident on new reactor designs. New reactor commissioning activities are a major part of all design specific working groups. The EPR and AP1000 Working Groups are particularly active in this area, as together they are overseeing 12 new reactor constructions worldwide. The design specific working groups have finalised a common position to provide high-level guidance to applicants and licensees that wish to take credit for a first plant only test (FPOT). This common position was first implemented in March 2017 at the Taishan 1 plant in China, where regulators and licensees from the United Kingdom, France and Finland witnessed reactor pressure vessel internals vibration tests. The FPOT marked a significant milestone for MDEP since it provided a unique opportunity for regulators involved to demonstrate the efficiency of using common positions to effectively collaborate and share information on test results. This model should be followed as much as possible in other MDEP co-operation areas. Another significant step in multinational regulatory co

  19. Experimental evaluation of human-system interaction on alarm design

    International Nuclear Information System (INIS)

    Huang, F.-H.; Lee, Y.-L.; Hwang, S.-L.; Yenn, T.-C.; Yu, Y.-C.; Hsu, C.-C.; Huang, H.-W.

    2007-01-01

    This study evaluates the practicability of automatic reset alarm system in Fourth Nuclear Power Plant (FNPP) of Taiwan. The features of auto-reset alarm system include dynamic prioritization of all alarm signals and fast system reset. Two experiments were conducted to evaluate the effect of automatic/manual reset on operation time, situational awareness (SA), task load index (TLX), and subjective ratings. All participants, including Experts and Novices, took part in the experiment on the alarm system simulator with Load Rejection procedure. The experimental results imply that the auto-reset alarm system may be applied in an advanced control room under Load Rejection procedure, because all participants' operation time were reduced as well as Novice's SA were raised up. Nevertheless, to ensure operating safety in FNPP, the effects of the auto-reset alarm system in other procedures/special situations still need to be tested in the near future

  20. Structural analysis and evaluation for the design of pressure vessel

    International Nuclear Information System (INIS)

    Arai, K.; Uragami, K.; Funada, T.; Baba, K.; Kira, T.

    1977-01-01

    For the design of pressure vessel, the detailed structural analysis such as the fatigue analysis under operating conditions is required by ASME Code or Japanese regulation. Accordingly, it should be verified by the analysis that the design of the pressure vessel is in compliance with the stress limitation defined in the Code or the regulation. However, it was apparent that the analysis is very complicated and takes a lot of time to evaluate in accordance with the Code requirements. Thereupon we developed the computer program by which we can perform the stress analysis with correctness and comparatively in a short period of design work reflecting the calculation results on detailed drawings to be used for fabrication. The computer program is controlled in combination with the system of the design work and out put list of the program can be directly used for the stress analysis report which is issued to customers. In addition to the above computer program, we developed the specific three dimensional finite element computer program to make sure of the structural integrity of the vessel head and flanges which are most complex for the analysis compared with the stress distribution measured by strain gauges on the vessel head and flange. Besides the structural analysis, the fracture mechanics analysis for the purpose of preventing the pressure vessel from the brittle fracture during heat-up and cool-down operation is also important and thereby we showed herein that the pressure vessel is in safety against the brittle fracture for the specified operating conditions. As a result of the above-mentioned analysis, the pressure vessel is designed with safety from the stand-points of the structural intensity and the fracture mechanics. (auth.)

  1. Evaluation of aluminum drill-pipe material and design

    Energy Technology Data Exchange (ETDEWEB)

    Placido, Joao C. [PETROBRAS, Rio de Janeiro, RJ (Brazil); Lourenco, Marcelo I.; Netto, Theodoro Antoun [Universidade Federal do Rio de Janeiro (UFRJ), RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia (COPPE)

    2008-07-01

    Experimental program and numerical analyses were carried out to investigate the fatigue mechanisms of aluminum drill pipes designed and manufactured in compliance with ISO 15546. The main objective is to improve the fatigue performance of these components by selecting the appropriate aluminum alloy and by enhancing the mechanical design of the threaded steel connector. This paper presents the experimental test program and numerical analyses conducted on a drill-pipe of different materials (Al-Cu-Mg and Al-Zn-Mg system aluminum alloys) and geometry. Material mechanical properties, including S-N curve, were determined through small-scale tests on specimens cut from actual drill pipes. Full-scale experiments were also performed in laboratory. A finite element model of the drill pipe, including the tool-joint region, was developed. The model simulates, through different load steps, the tool-joint hot assembly, and then reproduces the physical experiments numerically in order to obtain the actual stress distribution. Good correlation between full-scale and small-scale fatigue tests was obtained by adjusting the strain/stress levels monitored in the full-scale tests in light of the numerical simulations and performing fatigue life calculations via multiaxial fatigue models. The weak points of the current practice design are highlighted for further development. (author)

  2. Evaluation, including effects of storage and repeated freezing and thawing, of a method for measurement of urinary creatinine

    DEFF Research Database (Denmark)

    Garde, A H; Hansen, Åse Marie; Kristiansen, J

    2003-01-01

    The aims of this study were to elucidate to what extent storage and repeated freezing and thawing influenced the concentration of creatinine in urine samples and to evaluate the method for determination of creatinine in urine. The creatinine method was based on the well-known Jaffe's reaction...... and measured on a COBAS Mira autoanalyser from Roche. The main findings were that samples for analysis of creatinine should be kept at a temperature of -20 degrees C or lower and frozen and thawed only once. The limit of detection, determined as 3 x SD of 20 determinations of a sample at a low concentration (6...

  3. Design and Performance Evaluation of a Combined DHX unit for SFR Design Application

    International Nuclear Information System (INIS)

    Eoh, Jaehyuk; Kim, Dehee; Park, Chang-Gyu; Jeong, Ji-Young

    2015-01-01

    Based on a higher operating temperature with excellent thermal conductivity and larger thermal inertia of liquid sodium coolant, the SFR system has employed passive safety systems to ensure reliable decay heat removal (DHR) and consequential plant safety enhancement. Although a passive type DHR system has many advantages over an active one, designing a well coordinated passive system is usually more difficult than designing an effective active system. This is mainly because a cooling flow control is made directly by the system designer in an active system, while it is determined automatically by an intricate balance between the flow head loss and natural circulation head generation obtained from the density difference through the whole thermal flow system. To this end, securing a sufficient natural-circulation flow becomes one of the primary challenges for designing a reliable and successful Dh system in passive. In a current pool-type Sf design, an internal cooling flow path from the hot sodium pool to the cold pool is somewhat ambiguous owing to the split flow ratio formed in parallel paths between the intermediate heat exchangers (IHXs) and decay heat exchangers (DHXs), which results in a large uncertainty in the DHX shell-side flowrate and corresponding heat transfer to the DHR sodium loops. To improve passive the DHR performance, we proposed a new design concept with a simplified flow path from the hot pool to the cold pool through a unified flow path serially passing the DHX and IHX units. The present study aims at introducing the innovative design concept of the combined IHX-DHX unit and evaluating its design features in view of the heat transfer capability. From a comparison of the CHX performance designed by a one-dimensional approach with that made by a CFD analysis, it was quantitatively obtained that the difference in heat transfer rate is about 5.7%. It was also found that unexpected bypass flow in the shell-side CHX unit gave rise to a discrepancy

  4. Design and Evaluation of Microemulsion Gel System of Nadifloxacin

    Science.gov (United States)

    Shinde, Ujwala; Pokharkar, Sharda; Modani, Sheela

    2012-01-01

    Topical microemulsion systems for the antiacne agent, nadifloxacin were designed and developed to overcome the problems associated with the cutaneous delivery due to poor water solubility. The solubility of nadifloxacin in oils, surfactants and cosurfactants was evaluated to screen the components of the microemulsion. Various surfactants and cosurfactants were screened for their ability to emulsify the selected oily phase. The pseudoternary diagrams were constructed to identify the area of microemulsion existence. The influence of km (surfactant/cosurfactant) ratio on the microemulsion existence region was determined and optimum systems were designed. The systems were assessed for drug-loading efficiency and characterised for optical birefringence, pH and refractive index, robustness to dilution, globule size, drug content and thermodynamic stability. Optimised microemulsion systems were formulated into gel form and evaluated for viscosity, spreadability, drug content, ex vivo skin permeation and antibacterial activity. The maximum solubility of nadifloxacin in the microemulsion system was found to be 0.25%. The nadifloxacin microemulsions had a small and uniform globule size (67.3-121.23 nm). The stability results revealed that all formulations showed a stable globule size and the polydispersity index under stress conditions. Incorporation of nadifloxacin in microemulsion gel increased the ex vivo skin permeation and antibacterial activity when compared to marketed cream. PMID:23439454

  5. Maintainability design and evaluation of mechanical systems based on tribology

    International Nuclear Information System (INIS)

    Wani, M.F.; Gandhi, O.P.

    2002-01-01

    Maintainability of mechanical systems based on tribology is suggested and evaluated in this paper. Tribo-features of mechanical systems, which characterise maintainability are identified and are modelled in terms of tribo-maintainability digraph. The nodes in the digraph represent the tribo-features and edges represent the degree of influence among the features. A matrix, one to one representation of the digraph, is defined to develop system maintainability expression (SPF-t) based on the tribology. It is also useful in comparing the various design alternatives from tribo-maintainability point of view. Maintainability is evaluated from the tribo-maintainability index, obtained from SPF-t (i.e. permanent of the matrix) by substituting the numerical values of the features and their interdependence. A higher value of the index implies better maintainability of the systems. The proposed methodology also guides designers in enhancing the maintainability of a system by appropriately incorporating tribo-features. An example to illustrate the methodology is also presented

  6. Optimum parameters in a model for tumour control probability, including interpatient heterogeneity: evaluation of the log-normal distribution

    International Nuclear Information System (INIS)

    Keall, P J; Webb, S

    2007-01-01

    The heterogeneity of human tumour radiation response is well known. Researchers have used the normal distribution to describe interpatient tumour radiosensitivity. However, many natural phenomena show a log-normal distribution. Log-normal distributions are common when mean values are low, variances are large and values cannot be negative. These conditions apply to radiosensitivity. The aim of this work was to evaluate the log-normal distribution to predict clinical tumour control probability (TCP) data and to compare the results with the homogeneous (δ-function with single α-value) and normal distributions. The clinically derived TCP data for four tumour types-melanoma, breast, squamous cell carcinoma and nodes-were used to fit the TCP models. Three forms of interpatient tumour radiosensitivity were considered: the log-normal, normal and δ-function. The free parameters in the models were the radiosensitivity mean, standard deviation and clonogenic cell density. The evaluation metric was the deviance of the maximum likelihood estimation of the fit of the TCP calculated using the predicted parameters to the clinical data. We conclude that (1) the log-normal and normal distributions of interpatient tumour radiosensitivity heterogeneity more closely describe clinical TCP data than a single radiosensitivity value and (2) the log-normal distribution has some theoretical and practical advantages over the normal distribution. Further work is needed to test these models on higher quality clinical outcome datasets

  7. Implementation and evaluation of a simulation curriculum for paediatric residency programs including just-in-time in situ mock codes.

    Science.gov (United States)

    Sam, Jonathan; Pierse, Michael; Al-Qahtani, Abdullah; Cheng, Adam

    2012-02-01

    To develop, implement and evaluate a simulation-based acute care curriculum in a paediatric residency program using an integrated and longitudinal approach. Curriculum framework consisting of three modular, year-specific courses and longitudinal just-in-time, in situ mock codes. Paediatric residency program at BC Children's Hospital, Vancouver, British Columbia. The three year-specific courses focused on the critical first 5 min, complex medical management and crisis resource management, respectively. The just-in-time in situ mock codes simulated the acute deterioration of an existing ward patient, prepared the actual multidisciplinary code team, and primed the surrounding crisis support systems. Each curriculum component was evaluated with surveys using a five-point Likert scale. A total of 40 resident surveys were completed after each of the modular courses, and an additional 28 surveys were completed for the overall simulation curriculum. The highest Likert scores were for hands-on skill stations, immersive simulation environment and crisis resource management teaching. Survey results also suggested that just-in-time mock codes were realistic, reinforced learning, and prepared ward teams for patient deterioration. A simulation-based acute care curriculum was successfully integrated into a paediatric residency program. It provides a model for integrating simulation-based learning into other training programs, as well as a model for any hospital that wishes to improve paediatric resuscitation outcomes using just-in-time in situ mock codes.

  8. Evaluating progressive-rendering algorithms in appearance design tasks.

    Science.gov (United States)

    Jiawei Ou; Karlik, Ondrej; Křivánek, Jaroslav; Pellacini, Fabio

    2013-01-01

    Progressive rendering is becoming a popular alternative to precomputational approaches to appearance design. However, progressive algorithms create images exhibiting visual artifacts at early stages. A user study investigated these artifacts' effects on user performance in appearance design tasks. Novice and expert subjects performed lighting and material editing tasks with four algorithms: random path tracing, quasirandom path tracing, progressive photon mapping, and virtual-point-light rendering. Both the novices and experts strongly preferred path tracing to progressive photon mapping and virtual-point-light rendering. None of the participants preferred random path tracing to quasirandom path tracing or vice versa; the same situation held between progressive photon mapping and virtual-point-light rendering. The user workflow didn’t differ significantly with the four algorithms. The Web Extras include a video showing how four progressive-rendering algorithms converged (at http://youtu.be/ck-Gevl1e9s), the source code used, and other supplementary materials.

  9. Designing workload analysis questionnaire to evaluate needs of employees

    Science.gov (United States)

    Astuti, Rahmaniyah Dwi; Navi, Muhammad Abdu Haq

    2018-02-01

    Incompatibility between workload with work capacity is one of main problem to make optimal result. In case at the office, there are constraints to determine workload because of non-repetitive works. Employees do work based on the targets set in a working period. At the end of the period is usually performed an evaluation of employees performance to evaluate needs of employees. The aims of this study to design a workload questionnaire tools to evaluate the efficiency level of position as indicator to determine needs of employees based on the Indonesian State Employment Agency Regulation on workload analysis. This research is applied to State-Owned Enterprise PT. X by determining 3 positions as a pilot project. Position A is held by 2 employees, position B is held by 7 employees, and position C is held by 6 employees. From the calculation result, position A has an efficiency level of 1,33 or "very good", position B has an efficiency level of 1.71 or "enough", and position C has an efficiency level of 1.03 or "very good". The application of this tools giving suggestion the needs of employees of position A is 3 people, position B is 5 people, and position C is 6 people. The difference between the number of employees and the calculation result is then analyzed by interviewing the employees to get more data about personal perception. It can be concluded that this workload evaluation tools can be used as an alternative solution to evaluate needs of employees in office.

  10. Evaluation of three rapid oral fluid test devices on the screening of multiple drugs of abuse including ketamine.

    Science.gov (United States)

    Tang, Magdalene H Y; Ching, C K; Poon, Simon; Chan, Suzanne S S; Ng, W Y; Lam, M; Wong, C K; Pao, Ronnie; Lau, Angus; Mak, Tony W L

    2018-05-01

    Rapid oral fluid testing (ROFT) devices have been extensively evaluated for their ability to detect common drugs of abuse; however, the performance of such devices on simultaneous screening for ketamine has been scarcely investigated. The present study evaluated three ROFT devices (DrugWipe ® 6S, Ora-Check ® and SalivaScreen ® ) on the detection of ketamine, opiates, methamphetamine, cannabis, cocaine and MDMA. A liquid chromatography tandem mass spectrometry (LCMS) assay was firstly established and validated for confirmation analysis of the six types of drugs and/or their metabolites. In the field test, the three ROFT devices were tested on subjects recruited from substance abuse clinics/rehabilitation centre. Oral fluid was also collected using Quantisal ® for confirmation analysis. A total of 549 samples were collected in the study. LCMS analysis on 491 samples revealed the following drugs: codeine (55%), morphine (49%), heroin (40%), methamphetamine (35%), THC (8%), ketamine (4%) and cocaine (2%). No MDMA-positive cases were observed. Results showed that the overall specificity and accuracy were satisfactory and met the DRUID standard of >80% for all 3 devices. Ora-Check ® had poor sensitivities (ketamine 36%, methamphetamine 63%, opiates 53%, cocaine 60%, THC 0%). DrugWipe ® 6S showed good sensitivities in the methamphetamine (83%) and opiates (93%) tests but performed relatively poorly for ketamine (41%), cocaine (43%) and THC (22%). SalivaScreen ® also demonstrated good sensitivities in the methamphetamine (83%) and opiates (100%) tests, and had the highest sensitivity for ketamine (76%) and cocaine (71%); however, it failed to detect any of the 28 THC-positive cases. The test completion rate (proportion of tests completed with quality control passed) were: 52% (Ora-Check ® ), 78% (SalivaScreen ® ) and 99% (DrugWipe ® 6S). Copyright © 2018 Elsevier B.V. All rights reserved.

  11. Evaluation of 8-week body weight control program including sea tangle (Laminaria japonica) supplementation in Korean female college students

    Science.gov (United States)

    You, Jeong Soon; Sung, Min Jung

    2009-01-01

    This study was conducted to evaluate the effects of a body weight control program with supplementation of sea tangle (20 g/day) on 22 female college students. The contents of the program for 8 weeks contained diet therapy, exercise and behavioral modification through nutrition education. Body composition, dietary habit scores, serum lipid profiles, daily nutrient intakes and the quality of life were assessed at the beginning and at the end of the program. Average age of subjects and height were 20.8 years and 161.9 cm, respectively. After 8 weeks, there were significant reductions in body weight, body fat mass, percent body fat, waist-hip ratio and BMI. The dietary habit score such as a balanced diet, regularity of mealtime, overeating, eating while watching TV or using the computer and eating salty food were increased significantly. Serum lipid levels such as total cholesterol level, LDL-cholesterol level and triglyceride level were decreased but not significantly. There were decreases in intake of energy, protein and fat and increases in intakes of dietary fiber, folic acid, calcium and potassium from the beginning to the end of the program. There were significant improvements on subcomponents of quality of life; physical functioning, general-health and vitality. The limitation of this study was the fact that there was no control group, but an overall evaluation suggests the 8-week body weight control program consisting of diet therapy, exercise and behavioral modification with supplementation of sea tangle would be helpful to improve the body composition, dietary habits, daily nutrient intakes and quality of life in Korean female college students. PMID:20098584

  12. Design, construction and evaluation of solarized airlift tubular photobioreactor

    International Nuclear Information System (INIS)

    Bahadur, A; Zubair, M; Khan, M B

    2013-01-01

    An innovative photobioreactor is developed for growing algae in simulated conditions. The proposed design comprises of a continuous tubular irradiance loop and air induced liquid circulation with gas separation through air lift device. The unique features of air lift system are to ensure the shear free circulation of sensitive algal culture and induce light/dark cycles to the photosynthetic micro-organisms. The design strategy employs to model and construct a 20-liter laboratory scale unit using Boro-silicate glass tubing. The material is selected to ensure maximum photon transmission. All components of the device are designed to have flexibility to be replaced with an alternative design, providing fair chance of modification for future investigators. The principles of fluid mechanics are applied to describe geometrical attributes of the air lift system. Combination of LEDs and Florescent tube lights (Warm white) were used to illuminate the photosynthesis reaction area providing a possibility to control both illumination duration and light intensity. 200 Watt Solar PV system is designed to power up the device which included air pump (100 Watt) and illumination system (100 Watt). Algal strain Chlorella sp was inoculated in photobioreactor which was sparged with air and carbon dioxide. The growth was sustained in the batch mode with daily monitoring of temperature, pH and biomass concentration. The novel photobioreactor recorded a maximum experimental average yield of 0.65 g/l.day (11.3 g/m 2 .day) as compared to theoretical modeled yield of 0.82 g/l.day (14.26 g/m 2 .day), suggesting the device can be efficiently and cost-effectively employed in the production of algal biomass for biofuels, concomitantly mitigating CO 2 .

  13. Measurement-Based Performance Evaluation of Advanced MIMO Transceiver Designs

    Directory of Open Access Journals (Sweden)

    Schneider Christian

    2005-01-01

    Full Text Available This paper describes the methodology and the results of performance investigations on a multiple-input multiple-output (MIMO transceiver scheme for frequency-selective radio channels. The method relies on offline simulations and employs real-time MIMO channel sounder measurement data to ensure a realistic channel modeling. Thus it can be classified in between the performance evaluation using some predefined channel models and the evaluation of a prototype hardware in field experiments. New aspects for the simulation setup are discussed, which are frequently ignored when using simpler model-based evaluations. Example simulations are provided for an iterative ("turbo" MIMO equalizer concept. The dependency of the achievable bit error rate performance on the propagation characteristics and on the variation in some system design parameters is shown, whereas the antenna constellation is of particular concern for MIMO systems. Although in many of the considered constellations turbo MIMO equalization appears feasible in real field scenarios, there exist cases with poor performance as well, indicating that in practical applications link adaptation of the transmitter and receiver processing to the environment is necessary.

  14. Optimum Design of Braced Steel Space Frames including Soil-Structure Interaction via Teaching-Learning-Based Optimization and Harmony Search Algorithms

    OpenAIRE

    Ayse T. Daloglu; Musa Artar; Korhan Ozgan; Ali İ. Karakas

    2018-01-01

    Optimum design of braced steel space frames including soil-structure interaction is studied by using harmony search (HS) and teaching-learning-based optimization (TLBO) algorithms. A three-parameter elastic foundation model is used to incorporate the soil-structure interaction effect. A 10-storey braced steel space frame example taken from literature is investigated according to four different bracing types for the cases with/without soil-structure interaction. X, V, Z, and eccentric V-shaped...

  15. Optimum Design of Braced Steel Space Frames including Soil-Structure Interaction via Teaching-Learning-Based Optimization and Harmony Search Algorithms

    Directory of Open Access Journals (Sweden)

    Ayse T. Daloglu

    2018-01-01

    Full Text Available Optimum design of braced steel space frames including soil-structure interaction is studied by using harmony search (HS and teaching-learning-based optimization (TLBO algorithms. A three-parameter elastic foundation model is used to incorporate the soil-structure interaction effect. A 10-storey braced steel space frame example taken from literature is investigated according to four different bracing types for the cases with/without soil-structure interaction. X, V, Z, and eccentric V-shaped bracing types are considered in the study. Optimum solutions of examples are carried out by a computer program coded in MATLAB interacting with SAP2000-OAPI for two-way data exchange. The stress constraints according to AISC-ASD (American Institute of Steel Construction-Allowable Stress Design, maximum lateral displacement constraints, interstorey drift constraints, and beam-to-column connection constraints are taken into consideration in the optimum design process. The parameters of the foundation model are calculated depending on soil surface displacements by using an iterative approach. The results obtained in the study show that bracing types and soil-structure interaction play very important roles in the optimum design of steel space frames. Finally, the techniques used in the optimum design seem to be quite suitable for practical applications.

  16. A comprehensive economic evaluation of integrated desalination systems using fossil fuelled and nuclear energies and including their environmental costs

    International Nuclear Information System (INIS)

    Nisan, S.; Benzarti, N.

    2008-01-01

    Seawater desalination is now widely accepted as an attractive alternative source of freshwater for domestic and industrial uses. Despite the considerable progress made in the relevant technologies desalination, however, remains an energy intensive process in which the energy cost is the paramount factor. This Study is a first of a kind in that we have integrated the environmental costs into the power and desalination costs. The study has focused on the seawater desalination cost evaluation of the following systems. It is supposed that they will be operating in the co-generation mode (Simultaneous production of electrical power and desalted water) in 2015: Fossil fuelled based systems such as the coal and oil fired plants and the gas turbine combined cycle plant, coupled to MED, and RO; Pressurised water reactors such as the PWR-900 and the AP-600, coupled to MED, and RO; High temperature reactors such as the GT-MHR, the PBMR, coupled to MED, with the utilisation of virtually free waste-heat provided by these reactors. The study is made in real site-specific conditions of a site In Southern Europe. Sensitivity studies for different parameters such as the fossil fuel prices, interest and discount rates, power costs etc., have also been undertaken. The results obtained are then used to evaluate the financial interest of selected integrated desalination systems in terms of a detailed cash flow analysis, providing the net present values, pay back periods and the internal rate of returns. Analysis of the results shows that among the fossil fuelled systems the power and desalination costs by circulating fluidized bed coal fired plant would be the lowest with current coal prices. Those by oil fired plants would be highest. In all cases, integrated nuclear energy systems would lead to considerably lower power and water costs than the corresponding coal based systems. When external costs for different energies are internalized in power and water costs, the relative cost

  17. Evaluation of Seismic Response Trends from Long-Term Monitoring of Two Instrumented RC Buildings Including Soil-Structure Interaction

    Directory of Open Access Journals (Sweden)

    Faheem Butt

    2012-01-01

    Full Text Available This paper presents analyses of the seismic responses of two reinforced concrete buildings monitored for a period of more than two years. One of the structures was a three-storey reinforced concrete (RC frame building with a shear core, while the other was a three-storey RC frame building without a core. Both buildings are part of the same large complex but are seismically separated from the rest of it. Statistical analysis of the relationships between maximum free field accelerations and responses at different points on the buildings was conducted and demonstrated strong correlation between those. System identification studies using recorded accelerations were undertaken and revealed that natural frequencies and damping ratios of the building structures vary during different earthquake excitations. This variation was statistically examined and relationships between identified natural frequencies and damping ratios, and the peak response acceleration at the roof level were developed. A general trend of decreasing modal frequencies and increasing damping ratios was observed with increased level of shaking and response. Moreover, the influence of soil structure interaction (SSI on the modal characteristics was evaluated. SSI effects decreased the modal frequencies and increased some of the damping ratios.

  18. Evaluation of the anti-inflammatory actions of various functional food materials including glucosamine on synovial cells.

    Science.gov (United States)

    Yamagishi, Yoshie; Someya, Akimasa; Imai, Kensuke; Nagao, Junji; Nagaoka, Isao

    2017-08-01

    The anti-inflammatory actions of glucosamine (GlcN) on arthritic disorders involve the suppression of inflammatory mediator production from synovial cells. GlcN has also been reported to inhibit the activation of the p38 mitogen-activated protein kinase (MAPK) pathway. The present study aimed to determine the cooperative and anti‑inflammatory actions of functional food materials and evaluated the production of interleukin (IL)‑8 and phosphorylation of p38 MAPK in IL-1β-activated synovial cells, incubated with the combination of GlcN and various functional food materials containing L‑methionine (Met), undenatured type II collagen (UC‑II), chondroitin sulfate (CS), methylsulfonylmethane (MSM) and agaro-oligosaccharide (AO). The results indicated that Met, UC‑II, CS, MSM and AO slightly or moderately suppressed the IL-1β-stimulated IL‑8 production by human synovial MH7A cells. The same compounds further decreased the IL‑8 level lowered by GlcN. Similarly, they slightly suppressed the phosphorylation level of p38 MAPK and further reduced the phosphorylation level lowered by GlcN. These observations suggest a possibility that these functional food materials exert an anti‑inflammatory action (inhibition of IL‑8 production) in combination with GlcN by cooperatively suppressing the p38 MAPK signaling (phosphorylation).

  19. Subjective cognitive complaints included in diagnostic evaluation of dementia helps accurate diagnosis in a mixed memory clinic cohort

    DEFF Research Database (Denmark)

    Salem, L C; Vogel, Asmus Mejling; Ebstrup, J

    2015-01-01

    OBJECTIVE: Our objective was to examine the quantity and profile of subjective cognitive complaints in young patients as compared with elderly patients referred to a memory clinic. METHODS: Patients were consecutively recruited from the Copenhagen University Hospital Memory Clinic at Rigshospitalet....... In total, 307 patients and 149 age-matched healthy controls were included. Patients were classified in 4 diagnostic groups: dementia, mild cognitive impairment, affective disorders and no cognitive impairment. Subjective memory was assessed with subjective memory complaints (SMC) scale. Global cognitive...... with dementia have a significantly higher level and a different profile of subjective cognitive complaints as compared with elderly patients with dementia. Furthermore, young patients, diagnosed with an affective disorder, had the highest level of subjective cognitive complaints of all patients in a memory...

  20. En bloc resection of skull base tumor including internal carotid artery. Preoperative evaluation of cerebral blood flow

    International Nuclear Information System (INIS)

    Okamoto, Yoshitaka; Matsuzaki, Zensei; Kamijo, Atsushi; Ogino, Jun; Nagaseki, Yoshishige; Nukui, Hideaki; Yokomizo, Michinori; Togawa, Kiyoshi

    1998-01-01

    Carotid artery resection yields a possibility of cure in patients with advanced head and neck carcinoma involving the carotid artery. However, the criteria for the identification of those who are vulnerable to neurologic injury after resection have not been established. Interposition graft covered with a well-vascularized flap could minimize the rate of perioperative morbidity. Particularly, when an extensive resection of the skull base including carotid artery and sigmoid vein, is planned, extracranial-intracranial bypass should be considered to minimize the risks of neurologic morbidity, even if preresection positron emission tomography during balloon test occlusion of internal carotid artery suggested the adequacy of hemispheric collateral blood flow. In these cases, the temporary occlusion of the carotid artery is not an accurate prediction of the morbidity after permanent occlusion. (author)

  1. A new approach for evaluating water hammer including the initial state of pressurization of the installation and fluid

    Directory of Open Access Journals (Sweden)

    G. Kaless

    2016-04-01

    Full Text Available The water hammer phenomenon is well known since the 19th century, while its mathematical formulation, by means of differential equations, is due to works of researchers such us Allievi (1903 and others from the beginning of the 20th century. The equations found in the technical publications produce a strange water hammer when the initial condition is defined assuming an incompressible fluid and a rigid pipe. The correct solution requires solving the water hammer equations for the initial state. When the finite difference method is applied, the initial state is solved by means of a set of non-linear equations. A novel approach is proposed including the initial state of pressurization into the governing equations and hence simplifying the calculus of the initial conditions. Furthermore, a critical reading of the deduction of the equations is done pointing out conceptual inconsistencies and proposing corrections.

  2. Walkability Explorer. An Evaluation and Design Support Tool for Walkability

    Directory of Open Access Journals (Sweden)

    Ivan Blečić

    2014-05-01

    Full Text Available Walkability Explorer is a software tool for the evaluation of urban walkability which, we argue, is an important aspect of the quality of life in cities. Many conventional approaches to the assessment of quality of life measure the distribution, density and distances of different opportunities in space. But distance is not all there is. To reason in terms of urban capabilities of people we should also take into account the quality of pedestrian accessibility and of urban opportunities offered by the city. The software tool we present in this paper is an user-friendly implementation of such an evaluation approach to walkability. It includes several GIS and analysis features, and is interoperable with other standard GIS and data-analysis tools.

  3. Design, synthesis and biological evaluation of novel desmuramyldipeptide analogs.

    Science.gov (United States)

    Jakopin, Žiga; Corsini, Emanuela; Gobec, Martina; Mlinarič-Raščan, Irena; Dolenc, Marija Sollner

    2011-09-01

    A series of novel desmuramyldipeptides have been designed and synthesized as part of our search for therapeutically useful muramyldipeptide (MDP) analogs. Their immunomodulatory properties were initially assessed in vitro, evaluating their effect on lipopolysaccharide (LPS)-induced cytokine release in THP-1 cells. Following the initial screening, selected compounds were further investigated for immunomodulatory properties using LPS and phorbol 12-myristate 13-acetate (PMA)/ionomycin-stimulated human peripheral blood mononuclear cells. The results confirmed the immunomodulatory properties of some of the synthesized desmuramyldipeptide analogs. Taken together, presented data confirmed the immunostimulatory effect of compound 44, MDP derivative incorporating a pyrido-fused [1,2]-benzisothiazole moiety, while for compounds 32 and 39, indole scaffold-based derivatives of MDP, an immunosuppressive effect was observed. Further studies will be necessary to address their potential therapeutic use as immunomodulatory drugs, both as immunostimulants or anti-inflammatory agents. Copyright © 2011 Elsevier Masson SAS. All rights reserved.

  4. A passive exoskeleton with artificial tendons: design and experimental evaluation.

    Science.gov (United States)

    van Dijk, Wietse; van der Kooij, Herman; Hekman, Edsko

    2011-01-01

    We developed a passive exoskeleton that was designed to minimize joint work during walking. The exoskeleton makes use of passive structures, called artificial tendons, acting in parallel with the leg. Artificial tendons are elastic elements that are able to store and redistribute energy over the human leg joints. The elastic characteristics of the tendons have been optimized to minimize the mechanical work of the human leg joints. In simulation the maximal reduction was 40 percent. The performance of the exoskeleton was evaluated in an experiment in which nine subjects participated. Energy expenditure and muscle activation were measured during three conditions: Normal walking, walking with the exoskeleton without artificial tendons, and walking with the exoskeleton with the artificial tendons. Normal walking was the most energy efficient. While walking with the exoskeleton, the artificial tendons only resulted in a negligibly small decrease in energy expenditure. © 2011 IEEE

  5. Design & Evaluation of an Accessible Hybrid Violin Platform

    DEFF Research Database (Denmark)

    Overholt, Daniel; Gelineck, Steven

    2014-01-01

    We introduce and describe the initial evaluation of a new accessible (easily replicable) augmented violin prototype. Our research is focused on the user experience when playing such hybrid physical- digital instruments, and exploration of novel interactive performance techniques. The goal of wider...... platform accessibility for players and other researchers is approached via a simple ‘do-it-yourself’ design described herein. All hardware and software elements are open- source, and the build process requires minimal electronics skills. Cost has also been kept to a minimum where possible. Our initial...... that incorporates orientation/gesture sensors as well, with the resulting sound amplified and rendered via small speakers mounted directly to the instrument. The platform combines all necessary elements for digitally-mediated interactive performance; the need for a traditional computer only arises when developing...

  6. Designing and evaluating risk-based surveillance systems

    DEFF Research Database (Denmark)

    Willeberg, Preben; Nielsen, Liza Rosenbaum; Salman, Mo

    2012-01-01

    Risk-based surveillance systems reveal occurrence of disease or infection in a sample of population units, which are selected on the basis of risk factors for the condition under study. The purpose of such systems for supporting practical animal disease policy formulations and management decisions...... with prudent use of resources while maintaining acceptable system performance. High-risk category units are selected for testing by identification of the presence of specific high-risk factor(s), while disregarding other factors that might also influence the risk. On this basis we argue that the most...... applicable risk estimate for use in designing and evaluating a risk-based surveillance system would be a crude (unadjusted) relative risk, odds ratio or apparent prevalence. Risk estimates found in the published literature, however, are often the results of multivariable analyses implicitly adjusting...

  7. Design of Graphic Aggregation Model for Evaluation of Energy Systems

    International Nuclear Information System (INIS)

    An, Sang Ha; Jeong, Yong Hoon; Chang, Won Joon; Chang, Soon Heung; Kim, Sung Ho; Kim, Tae Woon

    2006-01-01

    Korea is meeting the growing electric power needs by mix of nuclear, fossil, hydro energy and so on. But we can not depend on fossil energy forever, and the people's concern about environment has been changed. So it is time to plan future energy mix considering multiple parameters such as economics, environment, social, energy security, etc. A multiple aggregation model has been used for decision making process in which multiple variables should be considered like energy mix. In this context, we designed Graphic Aggregation Model for Evaluation of energy systems (GAME) for the dynamic analysis of decision on the energy systems. It can support Analytic Hierarchy Process (AHP) analysis based on Graphic User Interface

  8. THE IMPORTANCE OF WEB DESIGN: VISUAL DESIGN EVALUATION OF DESTINATION WEB SITES

    OpenAIRE

    Fırlar, Belma; Okat Özdem, Özen

    2013-01-01

    As in the literature, the researchs about web site efficiency are mostly about site context. The analysis about function are mostly superficial. Whereas, controlling every little part of a web site respective is a necessity to show its efficiency. Here in this context in the study of perception and response event web sites that play an important role in visual design criteria are below the lens as featured and the web sites evaulated by heuristic evaluation method.The research focus of this s...

  9. Evaluation of the transmitted exposure through lead equivalent aprons used in a radiology department, including the contribution from backscatter

    International Nuclear Information System (INIS)

    Christodoulou, Emmanuel G.; Goodsitt, Mitchell M.; Larson, Sandra C.; Darner, Katie L.; Satti, Jahangir; Chan, H.-P.

    2003-01-01

    A study was conducted to evaluate the radiation transmission through lead equivalent aprons that are used in a radiology department. A large area beam (poor geometry) was employed for the transmission measurements, and backscatter was simulated by placing 7 '' of Lucite behind each apron. Separate ionization chambers were used to measure the incident and transmitted x-ray beams. Transmission measurements were made at 70 kVp and 100 kVp through aprons and protective shields from eight different vendors that were marked 0.25 mm and 0.5 mm lead equivalent. Transmissions through 0.254 mm and 0.508 mm of pure lead were also measured and were compared with the transmissions through the lead equivalent materials. In addition, the area densities of the aprons were measured to compare radiation transmission with respect to the weights of the aprons. At 70 kVp, the transmission through 0.254 mm of pure lead was 5.4% and the transmissions through the 0.25 mm lead equivalent materials were 4.3% to 10.2% with a mean value of 7.1% and a standard deviation (s.d.) of 1.4%. At 100 kVp, the values were 15% for 0.254 mm pure lead and 12.3% to 20.7% (mean 16.8%, s.d. 2.1%) for the 0.25 mm lead equivalent materials. The transmission through the 0.508 mm pure lead sample was 0.9% at 70 kVp, and the corresponding transmissions through the 0.5 mm lead equivalent materials were 0.6% to 1.6% (mean 1.0%, s.d. 0.2%). At 100 kVp, the transmission through the 0.508 mm lead sample was 5% and those through the 0.5 mm lead equivalent materials were 3.5% to 6.7% (mean 4.9%, s.d. 0.7%). The radiation transmissions at 70 kVp, through two 'lead-free' 0.5 mm lead equivalent aprons, were 1.7% and 1.9% and at 100 kVp the transmissions were 6.1% and 6.8%, respectively. This study indicates that there is a need to establish methods for acceptance testing of aprons and a need to establish acceptance limits for the x-ray transmission of aprons at specific kVp values. There is also a need for the

  10. Design, modeling, simulation and evaluation of a distributed energy system

    Science.gov (United States)

    Cultura, Ambrosio B., II

    This dissertation presents the design, modeling, simulation and evaluation of distributed energy resources (DER) consisting of photovoltaics (PV), wind turbines, batteries, a PEM fuel cell and supercapacitors. The distributed energy resources installed at UMass Lowell consist of the following: 2.5kW PV, 44kWhr lead acid batteries and 1500W, 500W & 300W wind turbines, which were installed before year 2000. Recently added to that are the following: 10.56 kW PV array, 2.4 kW wind turbine, 29 kWhr Lead acid batteries, a 1.2 kW PEM fuel cell and 4-140F supercapacitors. Each newly added energy resource has been designed, modeled, simulated and evaluated before its integration into the existing PV/Wind grid-connected system. The Mathematical and Simulink model of each system was derived and validated by comparing the simulated and experimental results. The Simulated results of energy generated from a 10.56kW PV system are in good agreement with the experimental results. A detailed electrical model of a 2.4kW wind turbine system equipped with a permanent magnet generator, diode rectifier, boost converter and inverter is presented. The analysis of the results demonstrates the effectiveness of the constructed simulink model, and can be used to predict the performance of the wind turbine. It was observed that a PEM fuel cell has a very fast response to load changes. Moreover, the model has validated the actual operation of the PEM fuel cell, showing that the simulated results in Matlab Simulink are consistent with the experimental results. The equivalent mathematical equation, derived from an electrical model of the supercapacitor, is used to simulate its voltage response. The model is completely capable of simulating its voltage behavior, and can predict the charge time and discharge time of voltages on the supercapacitor. The bi-directional dc-dc converter was designed in order to connect the 48V battery bank storage to the 24V battery bank storage. This connection was

  11. Evaluation and Comparison of Multiple Test Methods, Including Real-time PCR, for Legionella Detection in Clinical Specimens

    Science.gov (United States)

    Peci, Adriana; Winter, Anne-Luise; Gubbay, Jonathan B.

    2016-01-01

    Legionella is a Gram-negative bacterium that can cause Pontiac fever, a mild upper respiratory infection and Legionnaire’s disease, a more severe illness. We aimed to compare the performance of urine antigen, culture, and polymerase chain reaction (PCR) test methods and to determine if sputum is an acceptable alternative to the use of more invasive bronchoalveolar lavage (BAL). Data for this study included specimens tested for Legionella at Public Health Ontario Laboratories from 1st January, 2010 to 30th April, 2014, as part of routine clinical testing. We found sensitivity of urinary antigen test (UAT) compared to culture to be 87%, specificity 94.7%, positive predictive value (PPV) 63.8%, and negative predictive value (NPV) 98.5%. Sensitivity of UAT compared to PCR was 74.7%, specificity 98.3%, PPV 77.7%, and NPV 98.1%. Out of 146 patients who had a Legionella-positive result by PCR, only 66 (45.2%) also had a positive result by culture. Sensitivity for culture was the same using either sputum or BAL (13.6%); sensitivity for PCR was 10.3% for sputum and 12.8% for BAL. Both sputum and BAL yield similar results regardless testing methods (Fisher Exact p-values = 1.0, for each test). In summary, all test methods have inherent weaknesses in identifying Legionella; therefore, more than one testing method should be used. Obtaining a single specimen type from patients with pneumonia limits the ability to diagnose Legionella, particularly when urine is the specimen type submitted. Given ease of collection and similar sensitivity to BAL, clinicians are encouraged to submit sputum in addition to urine when BAL submission is not practical from patients being tested for Legionella. PMID:27630979

  12. Evaluation and comparison of multiple test methods, including real-time PCR, for Legionella detection in clinical specimens.

    Directory of Open Access Journals (Sweden)

    Adriana Peci

    2016-08-01

    Full Text Available Legionella is a gram-negative bacterium that can cause Pontiac fever, a mild upper respiratory infection and Legionnaire’s disease, a more severe illness. We aimed to compare the performance of urine antigen, culture and PCR test methods and to determine if sputum is an alternative to the use of more invasive bronchoalveolar lavage (BAL. Data for this study included specimens tested for Legionella at PHOL from January 1, 2010 to April 30, 2014, as part of routine clinical testing. We found sensitivity of UAT compared to culture to be 87%, specificity 94.7%, positive predictive value (PPV 63.8% and negative predictive value (NPV 98.5%. Sensitivity of UAT compared to PCR was 74.7%, specificity 98.3%, PPV 77.7% and NPV 98.1%. Of 146 patients who had a Legionella positive result by PCR, only 66(45.2% also had a positive result by culture. Sensitivity for culture was the same using either sputum or BAL (13.6%; sensitivity for PCR was 10.3% for sputum and 12.8% for BAL. Both sputum and BAL yield similar results despite testing methods (Fisher Exact p-values=1.0, for each test. In summary, all test methods have inherent weaknesses in identifying Legionella; thereforemore than one testing method should be used. Obtaining a single specimen type from patients with pneumonia limits the ability to diagnose Legionella, particularly when urine is the specimen type submitted. Given ease of collection, and similar sensitivity to BAL, clinicians are encouraged to submit sputum in addition to urine when BAL submission is not practical, from patients being tested for Legionella.

  13. ACS sampling system: design, implementation, and performance evaluation

    Science.gov (United States)

    Di Marcantonio, Paolo; Cirami, Roberto; Chiozzi, Gianluca

    2004-09-01

    By means of ACS (ALMA Common Software) framework we designed and implemented a sampling system which allows sampling of every Characteristic Component Property with a specific, user-defined, sustained frequency limited only by the hardware. Collected data are sent to various clients (one or more Java plotting widgets, a dedicated GUI or a COTS application) using the ACS/CORBA Notification Channel. The data transport is optimized: samples are cached locally and sent in packets with a lower and user-defined frequency to keep network load under control. Simultaneous sampling of the Properties of different Components is also possible. Together with the design and implementation issues we present the performance of the sampling system evaluated on two different platforms: on a VME based system using VxWorks RTOS (currently adopted by ALMA) and on a PC/104+ embedded platform using Red Hat 9 Linux operating system. The PC/104+ solution offers, as an alternative, a low cost PC compatible hardware environment with free and open operating system.

  14. Evaluation of divertor conceptual designs for a fusion power plant

    International Nuclear Information System (INIS)

    Ferrari, M.; Giancarli, L.; Kleefeldt, K.; Nardi, C.; Roedig, M.; Reimann, J.; Salavy, J.F.

    2001-01-01

    In the frame of the preliminary study of plants suitable for the energy production from the fusion power, particular emphasis has been given on the divertor studies. Since a significant percentage of the power generated from the fusion process is absorbed in the divertor, the thermal efficiency of the power conversion cycle requires a high coolant outlet temperature of the divertor, leading to solutions that are different from those adopted for the present experimental fusion plants. Therefore, copper alloys having extremely high thermal conductivity, cannot be used as structural material for this kind of devices. The most suitable coolants to be used in the divertor are water, helium and liquid metals. A conceptual design study has been developed for each of these three fluids, with the aim to evaluate the maximum allowable thermal flux at the divertor target plate and the R and D requirements for each solution. While a water-cooled divertor can be designed with a limited R and D effort, the development of helium or liquid metal cooled divertors requires a more engaging R and D program

  15. Safety Evaluation of Kartini Reactor Based on Instrumentation System Design

    International Nuclear Information System (INIS)

    Tjipta Suhaemi; Djen Djen Dj; Itjeu K; Johnny S; Setyono

    2003-01-01

    The safety of Kartini reactor has been evaluated based on instrumentation system aspect. The Kartini reactor is designed by BATAN. Design power of the reactor is 250 kW, but it is currently operated at 100 kW. Instrumentation and control system function is to monitor and control the reactor operation. Instrumentation and control system consists of safety system, start-up and automatic power control, and process information system. The linear power channel and logarithmic power channel are used for measuring power. There are 3 types of control rod for controlling the power, i.e. safety rod, shim rod, and regulating rod. The trip and interlock system are used for safety. There are instrumentation equipment used for measuring radiation exposure, flow rate, temperature and conductivity of fluid The system of Kartini reactor has been developed by introducing a process information system, start-up system, and automatic power control. It is concluded that the instrumentation of Kartini reactor has followed the requirement and standard of IAEA. (author)

  16. Proton exchange fuel cell : the design, construction and evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Heinzen, M.R.; Simoes, G.C.; Da Silva, L. [Univ. do Vale do Itajai, Sao Jose, SC (Brazil). Lab. de Pesquisa em Energia; Fiori, M.A.; Paula, M.M.S. [Univ. do Extremo Sul Catarinense, Santa Catarina (Brazil). Lab. de Sintese de Complexos Multifuncionais; Benavides, R. [Centro de Investigacion en Quimica Aplicada, Coahuila (Mexico)

    2010-07-15

    Polymer electrolyte membrane fuel cells (PEMFC) convert the chemical energy stored in the fuel directly into electrical energy without intermediate steps. The PEMFC operates at a relatively low operating temperature making it a good choice for mobile applications, but a high power density is needed in order to decrease the total weight of the vehicles. This paper presented a simple methodology to construct a PEMFC-type fuel cell, with particular reference to the gaseous diffuser, cell structure, the fixing plate, mounting bracket, gas distribution plates, and the membrane electrode assembly (MEA). The geometric design and meshing of the PEMFC were also described. The electrode was made using graphite with flow-field geometry. The PEMFC was tested for 100 hour of continuous work, during which time the current and voltage produced were monitored in order to evaluate the performance of the PEMFC. The materials used in the preparation of the fuel cell proved to be suitable. There was no loss of efficiency during the tests. The most relevant aspects affecting the PEMFC design were examined in an effort to optimize the performance of the cell. 13 refs., 6 figs.

  17. Design, formulation and evaluation of caffeine chewing gum.

    Science.gov (United States)

    Aslani, Abolfazl; Jalilian, Fatemeh

    2013-01-01

    Caffeine which exists in drinks such as coffee as well as in drug dosage forms in the global market is among the materials that increase alertness and decrease fatigue. Compared to other forms of caffeine, caffeine gum can create faster and more prominent effects. In this study, the main goal is to design a new formulation of caffeine gum with desirable taste and assess its physicochemical properties. Caffeine gum was prepared by softening of gum bases and then mixing with other formulation ingredients. To decrease the bitterness of caffeine, sugar, aspartame, liquid glucose, sorbitol, manitol, xylitol, and various flavors were used. Caffeine release from gum base was investigated by mechanical chewing set. Content uniformity test was also performed on the gums. The gums were evaluated in terms of organoleptic properties by the Latin-Square design at different stages. After making 22 formulations of caffeine gums, F11 from 20 mg caffeine gums and F22 from 50 mg caffeine gums were chosen as the best formulation in organoleptic properties. Both types of gum released about 90% of their own drug content after 30 min. Drug content of 20 and 50 mg caffeine gum was about 18.2-21.3 mg and 45.7-53.6 mg respectively. In this study, 20 and 50 mg caffeine gums with suitable and desirable properties (i.e., good taste and satisfactory release) were formulated. The best flavor for caffeine gum was cinnamon. Both kinds of 20 and 50 mg gums succeeded in content uniformity test.

  18. Design, Development and Evaluation of a Pneumatic Seeder for Automatic Planting of Seeds in Cellular Trays

    Directory of Open Access Journals (Sweden)

    E Movahedi

    2014-04-01

    Full Text Available For planting fine seeds in cellular trays, an automatic pneumatic seeder was designed, constructed and evaluated. CATIA software was used to design and analysis the system parts of the seeder. Different parts of the seeder, including vibrating seed hopper, vacuum boom, seed picking nozzles, seed tube, pneumatic system and electronic control unit for automation of the seeder, were designed and constructed. The area of nozzle orifice was used to calculate the required pressure of nozzle tip. The seeder was evaluated using two sizes of trays. Experiments were performed with five replications and the error of planting the seeds in the 105 and 390-cellular trays were 1.9 and 0.46 percent, respectively. The time of planting for 105 and 390 cellular trays reduced from 20 min (for manual seeding to 35 s and from 90 min to 160 s, respectively.

  19. Evaluation of urethane for feasibility of use in wind turbine blade design

    Science.gov (United States)

    Lieblein, S.; Ross, R. S.; Fertis, D. G.

    1979-01-01

    A preliminary evaluation was conducted of the use of cast urethane as a possible material for low-cost blades for wind turbines. Specimen test data are presented for ultimate tensile strength, elastic modulus, flexural strain, creep, and fatigue properties of a number of urethane formulations. Data are also included for a large-scale urethane blade section composed of cast symmetrical half-profiles tested as a cantilever beam. Based on these results, an analysis was conducted of a full-scale blade design of cast urethane that meets the design specifications of the rotor blades for the NASA/DOE experimental 100-kW MOD-0 wind turbine. Because of the low value of elastic modulus for urethane (around 457 000 psi), the design loads would have to be carried by metal reinforcement. Considerations for further evaluation are noted.

  20. Pharmaceutical Cocrystal of Piroxicam: Design, Formulation and Evaluation

    Science.gov (United States)

    Panzade, Prabhakar; Shendarkar, Giridhar; Shaikh, Sarfaraj; Balmukund Rathi, Pavan

    2017-01-01

    Purpose: Cocrystallisation of drug with coformers is a promising approach to alter the solid sate properties of drug substances like solubility and dissolution. The objective of the present work was to prepare, formulate and evaluate the piroxicam cocrystal by screening various coformers. Methods: Cocrystals of piroxicam were prepared by dry grinding method. The melting point and solubility of crystalline phase was determined. The potential cocrystal was characterized by DSC, IR, XRPD. Other pharmaceutical properties like solubility and dissolution rate were also evaluated. Orodispersible tablets of piroxicam cocrystal were formulated, optimized and evaluated using 32 factorial design. Results: Cocrystals of piroxicam-sodium acetate revealed the variation in melting points and solubility. The cocrystals were obtained in 1:1 ratio with sodium acetate. The analysis of Infrared explicitly indicated the shifting of characteristic bands of piroxicam. The X-Ray Powder Diffraction pattern denoted the crystallinity of cocrystals and noteworthy difference in 2θ value of intense peaks. Differential scanning calorimetry spectra of cocrystals indicated altered endotherms corresponding to melting point. The pH solubility profile of piroxicam showed sigmoidal curve, which authenticated the pKa-dependent solubility. Piroxicam cocrystals also exhibited a similar pH-solubility profile. The cocrystals exhibited faster dissolution rate owing to cocrystallization as evident from 30% increase in the extent of dissolution. The orodispersible tablets of piroxicam cocrystals were successfully prepared by direct compression method using crosscarmelose sodium as superdisintegrant with improved disintegration time (30 sec) and dissolution rate. Conclusion: The piroxicam cocrystal with modified properties was prepared with sodium acetate and formulated as orodispersible tablets having faster disintegration and greater dissolution rate. PMID:29071222

  1. Pharmaceutical Cocrystal of Piroxicam: Design, Formulation and Evaluation

    Directory of Open Access Journals (Sweden)

    Prabhakar Panzade

    2017-09-01

    Full Text Available Purpose: Cocrystallisation of drug with coformers is a promising approach to alter the solid sate properties of drug substances like solubility and dissolution. The objective of the present work was to prepare, formulate and evaluate the piroxicam cocrystal by screening various coformers. Methods: Cocrystals of piroxicam were prepared by dry grinding method. The melting point and solubility of crystalline phase was determined. The potential cocrystal was characterized by DSC, IR, XRPD. Other pharmaceutical properties like solubility and dissolution rate were also evaluated. Orodispersible tablets of piroxicam cocrystal were formulated, optimized and evaluated using 32 factorial design. Results: Cocrystals of piroxicam-sodium acetate revealed the variation in melting points and solubility. The cocrystals were obtained in 1:1 ratio with sodium acetate. The analysis of Infrared explicitly indicated the shifting of characteristic bands of piroxicam. The X-Ray Powder Diffraction pattern denoted the crystallinity of cocrystals and noteworthy difference in 2θ value of intense peaks. Differential scanning calorimetry spectra of cocrystals indicated altered endotherms corresponding to melting point. The pH solubility profile of piroxicam showed sigmoidal curve, which authenticated the pKa-dependent solubility. Piroxicam cocrystals also exhibited a similar pH-solubility profile. The cocrystals exhibited faster dissolution rate owing to cocrystallization as evident from 30% increase in the extent of dissolution. The orodispersible tablets of piroxicam cocrystals were successfully prepared by direct compression method using crosscarmelose sodium as superdisintegrant with improved disintegration time (30 sec and dissolution rate.Conclusion: The piroxicam cocrystal with modified properties was prepared with sodium acetate and formulated as orodispersible tablets having faster disintegration and greater dissolution rate.

  2. Design, formulation and evaluation of Aloe vera chewing gum

    Science.gov (United States)

    Aslani, Abolfazl; Ghannadi, Alireza; Raddanipour, Razieh

    2015-01-01

    Background: Aloe vera has antioxidant, antiinflammatory, healing, antiseptic, anticancer and antidiabetic effects. The aim of the present study was to design and evaluate the formulation of Aloe vera chewing gum with an appropriate taste and quality with the indications for healing oral wounds, such as lichen planus, mouth sores caused by cancer chemotherapy and mouth abscesses as well as reducing mouth dryness caused by chemotherapy. Materials and Methods: In Aloe vera powder, the carbohydrate content was determined according to mannose and phenolic compounds in terms of gallic acid. Aloe vera powder, sugar, liquid glucose, glycerin, sweeteners and different flavors were added to the soft gum bases. In Aloe vera chewing gum formulation, 10% of dried Aloe vera extract entered the gum base. Then the chewing gum was cut into pieces of suitable sizes. Weight uniformity, content uniformity, the organoleptic properties evaluation, releasing the active ingredient in the phosphate buffer (pH, 6.8) and taste evaluation were examined by Latin square method. Results: One gram of Aloe vera powder contained 5.16 ± 0.25 mg/g of phenolic compounds and 104.63 ± 4.72 mg/g of carbohydrates. After making 16 Aloe vera chewing gum formulations, the F16 formulation was selected as the best formulation according to its physicochemical and organoleptic properties. In fact F16 formulation has suitable hardness, lack of adhesion to the tooth and appropriate size and taste; and after 30 min, it released more than 90% of its drug content. Conclusion: After assessments made, the F16 formulation with maltitol, aspartame and sugar sweeteners was selected as the best formulation. Among various flavors used, peppermint flavor which had the most acceptance between consumers was selected. PMID:26605214

  3. Design and evaluation of the ONC health information technology curriculum.

    Science.gov (United States)

    Mohan, Vishnu; Abbott, Patricia; Acteson, Shelby; Berner, Eta S; Devlin, Corkey; Hammond, William E; Kukafka, Rita; Hersh, William

    2014-01-01

    As part of the Heath Information Technology for Economic and Clinical Health (HITECH) Act, the Office of the National Coordinator for Health Information Technology (ONC) implemented its Workforce Development Program, which included initiatives to train health information technology (HIT) professionals in 12 workforce roles, half of them in community colleges. To achieve this, the ONC tasked five universities with established informatics programs with creating curricular materials that could be used by community colleges. The five universities created 20 components that were made available for downloading from the National Training and Dissemination Center (NTDC) website. This paper describes an evaluation of the curricular materials by its intended audience of educators. We measured the quantity of downloads from the NTDC site and administered a survey about the curricular materials to its registered users to determine use patterns and user characteristics. The survey was evaluated using mixed methods. Registered users downloaded nearly half a million units or components from the NTDC website. We surveyed these 9835 registered users. 1269 individuals completed all or part of the survey, of whom 339 identified themselves as educators (26.7% of all respondents). This paper addresses the survey responses of educators. Successful aspects of the curriculum included its breadth, convenience, hands-on and course planning capabilities. Several areas were identified for potential improvement. The ONC HIT curriculum met its goals for community college programs and will likely continue to be a valuable resource for the larger informatics community in the future.

  4. Nuclear power plant human computer interface design incorporating console simulation, operations personnel, and formal evaluation techniques

    International Nuclear Information System (INIS)

    Chavez, C.; Edwards, R.M.; Goldberg, J.H.

    1993-01-01

    New CRT-based information displays which enhance the human machine interface are playing a very important role and are being increasingly used in control rooms since they present a higher degree of flexibility compared to conventional hardwired instrumentation. To prototype a new console configuration and information display system at the Experimental Breeder Reactor II (EBR-II), an iterative process of console simulation and evaluation involving operations personnel is being pursued. Entire panels including selector switches and information displays are simulated and driven by plant dynamical simulations with realistic responses that reproduce the actual cognitive and physical environment. Careful analysis and formal evaluation of operator interaction while using the simulated console will be conducted to determine underlying principles for effective control console design for this particular group of operation personnel. Additional iterations of design, simulation, and evaluation will then be conducted as necessary

  5. Toward time-based design: Creating an applied time evaluation checklist for urban design research

    Directory of Open Access Journals (Sweden)

    Amir Shakibamanesh

    2017-09-01

    Full Text Available The perception of a 3D space, in which movement takes place, is subjectively based on experience. The pedestrians’ perception of subjective duration is one of the related issues that receive little attention in urban design literature. Pedestrians often misperceive the required time to pass a certain distance. A wide range of factors affects one׳s perception of time in urban environments. These factors include individual factors (e.g., gender, age, and psychological state, social and cultural contexts, purpose and motivation for being in the space, and knowledge of the given area. This study aims to create an applied checklist that can be used by urban designers in analyzing the effects of individual experience on subjective duration. This checklist will enable urban designers to perform a phenomenological assessment of time perception and compare this perception in different urban spaces, thereby improving pedestrians’ experiences of time through a purposeful design. A combination of exploratory and descriptive analytical research is used as methodology due to the complexity of time perception.

  6. An investigation of how design managers in organisations in Bahrain manage and evaluate visual communication design for strategic advantage

    OpenAIRE

    Hallak, Lilian Issa Anton

    2015-01-01

    The role of visual communication design continues to increase in importance around the world. In Bahrain, organisations are increasingly considering visual communication design as a means of accomplishing organisational goals. The research aims to understand the process by which design managers in organisations in Bahrain manage and evaluate visual communication designs to gain strategic advantage. Even though the management of visual communication design has not yet been recognised as a ...

  7. US Department of Energy natural phenomena design/evaluation guidelines/lessons learned

    International Nuclear Information System (INIS)

    Conrads, T.J.

    1991-08-01

    In the spring of 1988, DOE Order 6430.1A, General Design Criteria [1], was issued for use. This document references UCRL-15910, Design and Evaluation Guidelines for DOE Facilities Subjected to Natural Phenomena Hazards [2], which is to be used as the basis for the design and evaluation of new and existing facilities to natural phenomena loading. Rather than use the historical deterministic methods for computing structural and component loading from potential natural phenomena, UCRL-15910 incorporated the years of hazards studies conducted throughout the US Department of Energy complex into probabilistic-based methods. This paper describes the process used to incorporate US Department of Energy natural phenomena design guidelines into the Hanford Plant Standards -- Standard Design Criteria for Architectural and Civil Standards [3]. It also addresses the subsequent use of these criteria during structural assessments of facilities, systems, and components of various vintage in support of updating safety analysis reports. The paper includes comparison of results using these most recent probabilistic-based natural phenomena loading criteria to those obtained from previous assessments, and it addresses the lessons learned from the many structural evaluations of 1940--1960 vintage buildings

  8. Seismic design evaluation guidelines for buried piping for the DOE HLW Facilities

    International Nuclear Information System (INIS)

    Lin, Chi-Wen; Antaki, G.; Bandyopadhyay, K.; Bush, S.H.; Costantino, C.; Kennedy, R.

    1995-01-01

    This paper presents the seismic design and evaluation guidelines for underground piping for the Department of Energy (DOE) High-Level-Waste (HLW) Facilities. The underground piping includes both single and double containment steel pipes and concrete pipes with steel lining, with particular emphasis on the double containment piping. The design and evaluation guidelines presented in this paper follow the generally accepted beam-on-elastic-foundation analysis principle and the inertial response calculation method, respectively, for piping directly in contact with the soil or contained in a jacket. A standard analysis procedure is described along with the discussion of factors deemed to be significant for the design of the underground piping. The following key considerations are addressed: the design feature and safety requirements for the inner (core) pipe and the outer pipe; the effect of soil strain and wave passage; assimilation of the necessary seismic and soil data; inertial response calculation for the inner pipe; determination of support anchor movement loads; combination of design loads; and code comparison. Specifications and justifications of the key parameters used, stress components to be calculated and the allowable stress and strain limits for code evaluation are presented

  9. Evaluation of Market Design Programme - Phase IV; Utvaerdering av Market Designprogrammet - etapp IV

    Energy Technology Data Exchange (ETDEWEB)

    Wall, Tomas

    2013-08-15

    The Market Design program was established in year 2000 to study issues related to markets, regulations and policy instruments related to the deregulation of the Swedish electricity market. Through the years, the focus has widened to include not only Sweden but also international cooperation on these issues. The fourth phase of the program is now underway between the years 2010 and 2013. The overall project objective of this fourth phase is to increase knowledge about the Nordic and North European electricity market. Specific objective is to create new knowledge that affects market design of the single market area (Nordic, EU) and to contribute to constructive meetings between researchers, energy companies and government agencies on Market Design Issues. The purpose of the evaluation of the Market Design Program phase IV has been to investigate the results and benefits of the program in relation to the program's original objectives and to examine the need for and areas of further research and possible ways for the research in Market Design. The evaluation has been carried through in four phases during spring and summer 2013. The work has included reading, interviews with program stakeholders, analysis and reporting.

  10. Climate services for society: origins, institutional arrangements, and design elements for an evaluation framework

    Science.gov (United States)

    Vaughan, Catherine; Dessai, Suraje

    2014-01-01

    Climate services involve the generation, provision, and contextualization of information and knowledge derived from climate research for decision making at all levels of society. These services are mainly targeted at informing adaptation to climate variability and change, widely recognized as an important challenge for sustainable development. This paper reviews the development of climate services, beginning with a historical overview, a short summary of improvements in climate information, and a description of the recent surge of interest in climate service development including, for example, the Global Framework for Climate Services, implemented by the World Meteorological Organization in October 2012. It also reviews institutional arrangements of selected emerging climate services across local, national, regional, and international scales. By synthesizing existing literature, the paper proposes four design elements of a climate services evaluation framework. These design elements include: problem identification and the decision-making context; the characteristics, tailoring, and dissemination of the climate information; the governance and structure of the service, including the process by which it is developed; and the socioeconomic value of the service. The design elements are intended to serve as a guide to organize future work regarding the evaluation of when and whether climate services are more or less successful. The paper concludes by identifying future research questions regarding the institutional arrangements that support climate services and nascent efforts to evaluate them. PMID:25798197

  11. Analytic evaluation of LAMPF II Booster Cavity design

    International Nuclear Information System (INIS)

    Friedrichs, C.C.

    1985-01-01

    Through the past few decades, a great deal of sophistication has evolved in the numeric codes used to evaluate electromagnetically resonant structures. The numeric methods are extremely precise, even for complicated geometries, whereas analytic methods require a simple uniform geometry and a simple, known mode configuration if the same precision is to be obtained. The code SUPERFISH, which is near the present state-of-the-art of numeric methods, does have the following limitations: No circumferential geometry variations are permissible; there are no provisions for magnetic or dielectric losses; and finally, it is impractical (because of the complexity of the code) to modify it to extract particular bits of data one might want that are not provided by the code as written. This paper describes how SUPERFISH was used as an aid in derivating an analytic model of the LAMPF II Booster Cavity. Once a satisfactory model was derived, simple FORTRAN codes were generated to provide whatever data was required. The analytic model is made up of TEM- and radial-mode transmission-line sections, as well as lumped elements where appropriate. Radial transmission-line equations, which include losses, were not found in any literature, and the extension of the lossless equations to include magnetic and dielectric losses are included in this paper

  12. Design, Construction, and Evaluation of Rubber Friction Tester

    Directory of Open Access Journals (Sweden)

    Mehdi Razzaghi Kashani

    2012-12-01

    Full Text Available Coeffcient of  friction  (COF  for  rubber parts  is one of  the key parameters in their interaction with solid rough surfaces (micrometer to millimeter scales,  such  as  tire-road  interactions. COF  of  rubber  depends  on  viscoelastic properties of rubber, roughness characteristics of the counter-part surface, and process variables such as contact nominal pressure and sliding speed. Due to the need for measuring COF  for  rubber,  a  new  friction  tester, with  continuous  variation  of nominal pressure and sliding speed, was designed and constructed in order to assess the effect of above mentioned parameters. Tire tread compounds, as the most common rubber part  in  the feld of  rubber  tribology, was used  for  this purpose. Viscoelastic properties of compounds were varied by changing composition of styrene-butadiene rubber (SBR and butadiene rubber (BR in the blend. Effect of surface roughness was evaluated by using silicon-carbide papers with different roughness parameters. By statistical analysis it was shown that the designed friction tester has high accuracy in measuring the coeffcient of friction of rubber and differentiating the effective parameters. Increasing the nominal pressure led to reduction of COF and increase in sliding speed forced it through a maximum. In conclusion, the loss factor of the compound and asymmetry in roughness distribution of the counter-surface are considered as the most effective parameters on COF of rubber.

  13. Design and evaluation of representative indoor radon surveys

    International Nuclear Information System (INIS)

    Csige, I.; Csegzi, S.

    2004-01-01

    We have developed a procedure to design and evaluate representative indoor radon surveys. The procedure is based on random sampling of a population of houses and careful statistical analysis of measured indoor radon concentrations. The method is designed to estimate the fraction of houses in which annual average 222 Rn activity concentration may exceed a certain reference level. Measurements of annual average indoor 222 Rn activity concentration were done in sleeping rooms at pillow level using etched track type radon detectors. We applied the above procedure in an old fashioned village and in a fast developing small city in Transylvania, Romania. In the village almost all houses were single floor wooden made houses without cellar built with traditional technology on a geologically uniform area. The distribution of indoor 222 Rn activity concentration in a sample of 115 houses can almost perfectly be fitted with log-normal probability density function. The correlation coefficient of linear fitting on linearized scales was k = -0.9980. The percentages of houses expected to have annual average 222 Rn activity concentration higher than 400 Bq m -3 is less than 1 %, and of those higher than 600 Bq m -3 can be estimated to be around 0.1 %. The small city, on the other hand lies on a geologically inhomogeneous area, and house construction technology has also changed dramatically in past decades. The resulting distribution of measured indoor 222 Rn activity concentration in a sample of 116 houses cannot be fitted with any simple probability density function. Therefore the prediction of the fraction of houses in which the annual average 222 Rn activity concentration may exceed a certain reference level could not be done adequately. With certain assumptions we estimated that the percentages of houses expected to have annual average 222 Rn activity concentration higher than 400 Bq m -3 is between 3 and 7 %, and of those higher than 600 Bq m -3 can be estimated to be between

  14. Design, formulation and evaluation of nicotine chewing gum.

    Science.gov (United States)

    Aslani, Abolfazl; Rafiei, Sahar

    2012-01-01

    Nicotine replacement therapy (NRT) can help smokers to quit smoking. Nicotine chewing gum has attracted the attention from pharmaceutical industries to offer it to consumers as an easily accessible NRT product. However, the bitter taste of such gums may compromise their acceptability by patients. This study was, therefore, designed to develop 2 and 4 mg nicotine chewing gums of pleasant taste, which satisfy the consumers the most. Nicotine, sugar, liquid glucose, glycerin, different sweetening and taste-masking agents, and a flavoring agent were added to the gum bases at appropriate temperature. The medicated gums were cut into pieces of suitable size and coated by acacia aqueous solution (2% w/v), sugar dusting, followed by acacia-sugar-calcium carbonate until a smooth surface was produced. The gums' weight variation and content uniformity were determined. The release of nicotine was studied in pH 6.8 phosphate buffer using a mastication device which simulated the mastication of chewing gum in human. The Latin Square design was used for the evaluation of organoleptic characteristics of the formulations at different stages of development. Most formulations released 79-83% of their nicotine content within 20 min. Nicotine-containing sugar-coated gums in which aspartame as sweetener and cherry and eucalyptus as flavoring agents were incorporated (i.e. formulations F(19-SC) and F(20-SC), respectively) had optimal chewing hardness, adhering to teeth, and plumpness characteristics, as well as the most pleasant taste and highest acceptability to smokers. Taste enhancement of nicotine gums was achieved where formulations comprised aspartame as the sweetener and cherry and eucalyptus as the flavoring agents. Nicotine gums of pleasant taste may, therefore, be used as NRT to assist smokers quit smoking.

  15. Designing and Evaluating an Online Role Play in Conflict Management

    Science.gov (United States)

    Hrastinski, Stefan; Watson, Jason

    2009-01-01

    Purpose: This paper aims to identify, through a literature review, key issues regarding how online role plays can be designed and to apply them when designing a role play on conflict management. Design/methodology/approach: By drawing on the key issues identified in the literature review, a role play on conflict management was designed and…

  16. Post-Occupancy Evaluation of a Mental Healthcare Facility Based on Staff Perceptions of Design Innovations.

    Science.gov (United States)

    Kalantari, Saleh; Snell, Robin

    2017-07-01

    This study was a post-occupancy evaluation (POE) to examine the effectiveness of three specific design innovations in a mental healthcare facility. In addition to collecting data about the impact of these specific designs, the study provides a model for the broader implementation of POE approaches in the mental healthcare context. POEs in general healthcare settings have been shown to lead to better work environments and better outcomes for patients. Despite growing evidence of the value provided by POE studies, the industry has been somewhat slow to adopt their regular use, in part due to unfamiliarity with the POE process. This is particularly true in mental healthcare contexts, where POE studies remain virtually nonexistent. In-depth interviews and a widely distributed, anonymous survey were used to collect hospital staff perceptions and feedback regarding the impact of specific design features. The hospital staff were quite enthusiastic about two of the design innovations studied here (a new wayfinding strategy and the use of vibrant colors in specific areas of the facility). The third innovation, open-style communication centers, elicited more mixed evaluations. The results include extensive hypothesis testing about the effects of each innovation as well as narrative discussions of their pros and cons. The study generated new knowledge about three specific mental healthcare design innovations and provides a model for the practical implementation of a POE approach in mental healthcare contexts. The results are particularly relevant for designers who are considering innovative strategies in future mental healthcare facilities.

  17. Design and Evaluation of a Wireless Sensor Network Based Aircraft Strength Testing System

    Science.gov (United States)

    Wu, Jian; Yuan, Shenfang; Zhou, Genyuan; Ji, Sai; Wang, Zilong; Wang, Yang

    2009-01-01

    The verification of aerospace structures, including full-scale fatigue and static test programs, is essential for structure strength design and evaluation. However, the current overall ground strength testing systems employ a large number of wires for communication among sensors and data acquisition facilities. The centralized data processing makes test programs lack efficiency and intelligence. Wireless sensor network (WSN) technology might be expected to address the limitations of cable-based aeronautical ground testing systems. This paper presents a wireless sensor network based aircraft strength testing (AST) system design and its evaluation on a real aircraft specimen. In this paper, a miniature, high-precision, and shock-proof wireless sensor node is designed for multi-channel strain gauge signal conditioning and monitoring. A cluster-star network topology protocol and application layer interface are designed in detail. To verify the functionality of the designed wireless sensor network for strength testing capability, a multi-point WSN based AST system is developed for static testing of a real aircraft undercarriage. Based on the designed wireless sensor nodes, the wireless sensor network is deployed to gather, process, and transmit strain gauge signals and monitor results under different static test loads. This paper shows the efficiency of the wireless sensor network based AST system, compared to a conventional AST system. PMID:22408521

  18. Design and evaluation of a wireless sensor network based aircraft strength testing system.

    Science.gov (United States)

    Wu, Jian; Yuan, Shenfang; Zhou, Genyuan; Ji, Sai; Wang, Zilong; Wang, Yang

    2009-01-01

    The verification of aerospace structures, including full-scale fatigue and static test programs, is essential for structure strength design and evaluation. However, the current overall ground strength testing systems employ a large number of wires for communication among sensors and data acquisition facilities. The centralized data processing makes test programs lack efficiency and intelligence. Wireless sensor network (WSN) technology might be expected to address the limitations of cable-based aeronautical ground testing systems. This paper presents a wireless sensor network based aircraft strength testing (AST) system design and its evaluation on a real aircraft specimen. In this paper, a miniature, high-precision, and shock-proof wireless sensor node is designed for multi-channel strain gauge signal conditioning and monitoring. A cluster-star network topology protocol and application layer interface are designed in detail. To verify the functionality of the designed wireless sensor network for strength testing capability, a multi-point WSN based AST system is developed for static testing of a real aircraft undercarriage. Based on the designed wireless sensor nodes, the wireless sensor network is deployed to gather, process, and transmit strain gauge signals and monitor results under different static test loads. This paper shows the efficiency of the wireless sensor network based AST system, compared to a conventional AST system.

  19. 75 FR 1622 - Decision To Evaluate a Petition To Designate a Class of Employees for the General Electric...

    Science.gov (United States)

    2010-01-12

    ... Employees for the General Electric Company, Evendale, OH, To Be Included in the Special Exposure Cohort... evaluate a petition to designate a class of employees for the General Electric Company, Evendale, Ohio, to... Compensation Program Act of 2000. The initial proposed definition for the class being evaluated, subject to...

  20. 75 FR 67364 - Decision To Evaluate a Petition To Designate a Class of Employees From Clinton Engineering Works...

    Science.gov (United States)

    2010-11-02

    ... Employees From Clinton Engineering Works in Oak Ridge, TN, To Be Included in the Special Exposure Cohort... evaluate a petition to designate a class of employees from Clinton Engineering Works in Oak Ridge... Compensation Program Act of 2000. The initial proposed definition for the class being evaluated, subject to...

  1. Developing Students' Creative Self-Efficacy Based on Design-Thinking: Evaluation of an Elective University Course

    Science.gov (United States)

    Ohly, Sandra; Plückthun, Laura; Kissel, Dorothea

    2017-01-01

    The development of novel and useful ideas is a process that can be described in multiple steps, including information gathering, generating ideas and evaluating ideas. We evaluated a university course that was developed based on design thinking principles which employ similar steps. Our results show that the course was not effective in enhancing…

  2. 76 FR 70456 - Decision To Evaluate a Petition To Designate a Class of Employees From Sandia National Laboratory...

    Science.gov (United States)

    2011-11-14

    ... Employees From Sandia National Laboratory, Albuquerque, NM, To Be Included in the Special Exposure Cohort... evaluate a petition to designate a class of employees from Sandia National Laboratory, Albuquerque, New... revision as warranted by the evaluation, is as follows: Facility: Sandia National Laboratory. Location...

  3. 75 FR 22409 - Decision To Evaluate a Petition To Designate a Class of Employees From the Sandia National...

    Science.gov (United States)

    2010-04-28

    ... Employees From the Sandia National Laboratory in Albuquerque, NM, To Be Included in the Special Exposure... decision to evaluate a petition to designate a class of employees from the Sandia National Laboratory in..., subject to revision as warranted by the evaluation, is as follows: Facility: Sandia National Laboratory...

  4. Design and evaluation of the MAMMI dedicated breast PET

    International Nuclear Information System (INIS)

    Moliner, L.; González, A. J.; Soriano, A.; Sánchez, F.; Correcher, C.; Orero, A.; Carles, M.; Vidal, L. F.; Barberá, J.; Caballero, L.; Seimetz, M.; Vázquez, C.; Benlloch, J. M.

    2012-01-01

    Purpose: A breast dedicated positron emission tomography (PET) scanner has been developed based on monolithic LYSO crystals coupled to position sensitive photomultiplier tubes (PSPMTs). In this study, we describe the design of the PET system and report on its performance evaluation. Methods: MAMMI is a breast PET scanner based on monolithic LYSO crystals. It consists of 12 compact modules with a transaxial field of view (FOV) of 170 mm in diameter and 40 mm axial FOV that translates to cover up to 170 mm. The patient lies down in a prone position that facilitates maximum breast elongation. Quantitative performance analysis of the calculated method for the attenuation correction specifically developed for MAMMI, and based on PET image segmentation, has also been conducted in this evaluation. In order to fully determine the MAMMI prototype's performance, we have adapted the measurements suggested for National Electrical Manufacturers Association (NEMA) NU 2-2007 and NU 4-2008 protocol tests, as they are defined for whole-body and small animal PET scanners, respectively. Results: Spatial resolutions of 1.6, 1.8, and 1.9 mm were measured in the axial, radial, and tangential directions, respectively. A scatter fraction of 20.8% was obtained and the maximum NEC was determined to be 25 kcps at 44 MBq. The average sensitivity of the system was observed to be 1% for an energy window of (250 keV–750 keV) and a maximum absolute sensitivity of 1.8% was measured at the FOV center. Conclusions: The overall performance of the MAMMI reported on this evaluation quantifies its ability to produce high quality PET images. Spatial resolution values below 3 mm were measured in most of the FOV. Only the radial component of spatial resolution exceeds the 3 mm at radial positions larger than 60 mm. This study emphasizes the need for standardized testing methodologies for dedicated breast PET systems similar to NEMA standards for whole-body and small animal PET scanners.

  5. BWR power oscillation evaluation methodologies in core design

    International Nuclear Information System (INIS)

    Hotta, Akitoshi

    1995-01-01

    At the initial stage of BWR development, the power oscillation due to the nuclear-thermal interaction originated in random boiling phenomena and nuclear void feedback was feared. But it was shown that under the high pressure condition in the normal operation of recent commercial BWRs, the core is in very stable state. However, power oscillation events have been observed in actual machines, and it is necessary to do the stability evaluation that sufficiently reflects the detailed operation conditions of actual plants. As the cause of power oscillation events, the instability of control system and nuclear-thermal coupling instability are important, and their mechanisms are explained. As the model for analyzing the stability of BWR core, the nuclear-thermal coupling model in frequency domain is the central existence. As the information for the design, the parameters of fuel assemblies, and the nuclear parameters and the thermohydraulic parameters of cores are enumerated. LAPUR-TSI is a nuclear-thermal coupling model. The analysis system in the software of Tokyo Electric Power Co. is outlined, and the analysis model was verified. (K.I.)

  6. Design and evaluation of nicorandil extended-release tablet

    Directory of Open Access Journals (Sweden)

    Ju-Young Kim

    2015-04-01

    Full Text Available The aim of this study was to design and evaluate extended-release formulations of a model drug, nicorandil, in order to achieve the desired steady-state plasma concentration of drug in vivo. Simulation was employed to estimate optimum dissolution and absorption rate of nicorandil. The dissolution test was employed using pH 1.2, 4.0, 6.8 buffer solution, or water, to measure the in vitro release behaviors of nicorandil formulations. A single dose (15 mg of each formulation was orally administered to four beagle dogs under fasted conditions, and the pharmacokinetic parameters were calculated. The in vitro/in vivo relationship of the extended-release formulation was confirmed using in vitro dissolution profiles and plasma concentrations of drug in beagle dogs. Nicorandil was released completely within 30 min from the immediate-release tablets and released for 24 h from the extended-release tablets. The nicorandil plasma concentration could be modified by adjusting the drug release rate from the extended-release formulation. The release rate of nicorandil was the rate-limiting step in the overall absorption of drug from the extended-release formulations. These results highlight the potential of a nicorandil extended-release formulation in the treatment of angina pectoris.

  7. Development of panel loudspeaker system: design, evaluation and enhancement.

    Science.gov (United States)

    Bai, M R; Huang, T

    2001-06-01

    Panel speakers are investigated in terms of structural vibration and acoustic radiation. A panel speaker primarily consists of a panel and an inertia exciter. Contrary to conventional speakers, flexural resonance is encouraged such that the panel vibrates as randomly as possible. Simulation tools are developed to facilitate system integration of panel speakers. In particular, electro-mechanical analogy, finite element analysis, and fast Fourier transform are employed to predict panel vibration and the acoustic radiation. Design procedures are also summarized. In order to compare the panel speakers with the conventional speakers, experimental investigations were undertaken to evaluate frequency response, directional response, sensitivity, efficiency, and harmonic distortion of both speakers. The results revealed that the panel speakers suffered from a problem of sensitivity and efficiency. To alleviate the problem, a woofer using electronic compensation based on H2 model matching principle is utilized to supplement the bass response. As indicated in the result, significant improvement over the panel speaker alone was achieved by using the combined panel-woofer system.

  8. Societal risk approach to safeguards design and evaluation

    International Nuclear Information System (INIS)

    Bennett, C.A.; Murphey, W.M.; Sherr, T.S.

    1975-06-01

    There has been much discussion and public debate concerning the effectiveness of the national system of safeguards against malevolent acts involving nuclear materials. Useful dialogue on this subject has been hampered by the lack of well-defined objectives, system parameters and boundary conditions as a framework for communication. This study provides such a framework. Expressing the safeguards objective in terms of societal risk represents a change in focus, rather than intent, from the earlier view of safeguards as a system for protecting nuclear material against theft or diversion. The study defines both the safeguards problem and the safeguards system in terms that can be related to the general safeguards objective. It is axiomatic that the first step to an effective solution is a careful definition of the problem. The significant and immediate value of this study lies in the rigorous definition and systematic organization of recognized elements into a coherent and comprehensive pattern. Although the title specifically addresses design and evaluation, the framework provided by the study will be a useful management tool for safeguards implementation and administration as well. (U.S.)

  9. Design Methodology and Performance Evaluation of New Generation Sounding Rockets

    Directory of Open Access Journals (Sweden)

    Marco Pallone

    2018-01-01

    Full Text Available Sounding rockets are currently deployed for the purpose of providing experimental data of the upper atmosphere, as well as for microgravity experiments. This work provides a methodology in order to design, model, and evaluate the performance of new sounding rockets. A general configuration composed of a rocket with four canards and four tail wings is sized and optimized, assuming different payload masses and microgravity durations. The aerodynamic forces are modeled with high fidelity using the interpolation of available data. Three different guidance algorithms are used for the trajectory integration: constant attitude, near radial, and sun-pointing. The sun-pointing guidance is used to obtain the best microgravity performance while maintaining a specified attitude with respect to the sun, allowing for experiments which are temperature sensitive. Near radial guidance has instead the main purpose of reaching high altitudes, thus maximizing the microgravity duration. The results prove that the methodology at hand is straightforward to implement and capable of providing satisfactory performance in term of microgravity duration.

  10. Design and Evaluation of a Cross-Cultural Training System

    Science.gov (United States)

    Santarelli, Thomas; Stagl, Kevin C.

    2011-01-01

    Cross-cultural competency, and the underlying communication and affective skills required to develop such expertise, is becoming increasingly important for a wide variety of domains. To address this need, we developed a blended learning platform which combines virtual role-play with tutorials, assessment and feedback. A Middle-Eastern Curriculum (MEC) exemplar for cross-cultural training U.S. military personnel was developed to guide the refinement of an existing game-based training platform. To complement this curriculum, we developed scenario authoring tools to enable end-users to define training objectives, link performance measures and feedback/remediation to these objectives, and deploy experiential scenarios within a game-based virtual environment (VE). Lessons learned from the design and development of this exemplar cross-cultural competency curriculum, as well as formative evaluation results, are discussed. Initial findings suggest that the underlying training technology promotes deep levels of semantic processing of the key information of relevant cultural and communication skills.

  11. Innovative Design and Performance Evaluation of Bionic Imprinting Toothed Wheel.

    Science.gov (United States)

    Zhang, Zhihong; Wang, Xiaoyang; Tong, Jin; Stephen, Carr

    2018-01-01

    A highly efficient soil-burrowing dung beetle possesses an intricate outer contour curve on its foreleg end-tooth. This study was carried out based on evidence that this special outer contour curve has the potential of reducing soil penetration resistance and could enhance soil-burrowing efficiency. A toothed wheel is a typical agricultural implement for soil imprinting, to increase its working efficiency; the approach of the bionic geometrical structure was utilized to optimize the innovative shape of imprinting toothed wheel. Characteristics in the dung beetle's foreleg end-tooth were extracted and studied by the edge detection technique. Then, this special outer contour curve was modeled by a nine-order polynomial function and used for the innovative design of imprinting the tooth's cutting edge. Both the conventional and bionic teeth were manufactured, and traction tests in a soil bin were conducted. Taking required draft force and volume of imprinted microbasin as the evaluating indexes, operating efficiency and quality of different toothed wheels were compared and investigated. Results indicate that compared with the conventional toothed wheel, a bionic toothed wheel possesses a better forward resistance reduction property against soil and, meanwhile, can enhance the quality of soil imprinting by increasing the volume of the created micro-basin.

  12. A Reinvestigation of the Dimer of para-Benzoquinone with Pyrimidine with MP2, CCSD(T) and DFT using Functionals including those Designed to Describe Dispersion

    Science.gov (United States)

    Marianski, Mateusz; Oliva, Antoni

    2012-01-01

    We reevaluate the interaction of pyridine and p-benzoquinone using functionals designed to treat dispersion. We compare the relative energies of four different structures: stacked, T-shaped (identified for the first time) and two planar H-bonded geometries using these functionals (B97-D, ωB97x-D, M05, M05-2X, M06, M06L, M06-2X), other functionals (PBE1PBE, B3LYP, X3LYP), MP2 and CCSD(T) using basis sets as large as cc-pVTZ. The functionals designed to treat dispersion behave erratically as the predictions of the most stable structure vary considerably. MP2 predicts the experimentally observed structure (H-bonded) to be the least stable, while single point CCSD(T) at the MP2 optimized geometry correctly predicts the observed structure to be most stable. We have confirmed the assignment of the experimental structure using new calculations of the vibrational frequency shifts previously used to identify the structure. The MP2/cc-pVTZ vibrational calculations are in excellent agreement with the observations. All methods used to calculate the energies provide vibrational shifts that agree with the observed structure even though most do not predict this structure to be most stable. The implications for evaluating possible π-stacking in biologically important systems are discussed. PMID:22765283

  13. A reinvestigation of the dimer of para-benzoquinone and pyrimidine with MP2, CCSD(T), and DFT using functionals including those designed to describe dispersion.

    Science.gov (United States)

    Marianski, Mateusz; Oliva, Antoni; Dannenberg, J J

    2012-08-02

    We reevaluate the interaction of pyridine and p-benzoquinone using functionals designed to treat dispersion. We compare the relative energies of four different structures: stacked, T-shaped (identified for the first time), and two planar H-bonded geometries using these functionals (B97-D, ωB97x-D, M05, M05-2X, M06, M06L, and M06-2X), other functionals (PBE1PBE, B3LYP, X3LYP), MP2, and CCSD(T) using basis sets as large as cc-pVTZ. The functionals designed to treat dispersion behave erratically as the predictions of the most stable structure vary considerably. MP2 predicts the experimentally observed structure (H-bonded) to be the least stable, while single-point CCSD(T) at the MP2 optimized geometry correctly predicts the observed structure to be the most stable. We have confirmed the assignment of the experimental structure using new calculations of the vibrational frequency shifts previously used to identify the structure. The MP2/cc-pVTZ vibrational calculations are in excellent agreement with the observations. All methods used to calculate the energies provide vibrational shifts that agree with the observed structure even though most do not predict this structure to be most stable. The implications for evaluating possible π-stacking in biologically important systems are discussed.

  14. Using theory of change to design and evaluate public health interventions: a systematic review.

    Science.gov (United States)

    Breuer, Erica; Lee, Lucy; De Silva, Mary; Lund, Crick

    2016-05-06

    Despite the increasing popularity of the theory of change (ToC) approach, little is known about the extent to which ToC has been used in the design and evaluation of public health interventions. This review aims to determine how ToCs have been developed and used in the development and evaluation of public health interventions globally. We searched for papers reporting the use of "theory of change" in the development or evaluation of public health interventions in databases of peer-reviewed journal articles such as Scopus, Pubmed, PsychInfo, grey literature databases, Google and websites of development funders. We included papers of any date, language or study design. Both abstracts and full text papers were double screened. Data were extracted and narratively and quantitatively summarised. A total of 62 papers were included in the review. Forty-nine (79 %) described the development of ToC, 18 (29 %) described the use of ToC in the development of the intervention and 49 (79 %) described the use of ToC in the evaluation of the intervention. Although a large number of papers were included in the review, their descriptions of the ToC development and use in intervention design and evaluation lacked detail. The use of the ToC approach is widespread in the public health literature. Clear reporting of the ToC process and outputs is important to strengthen the body of literature on practical application of ToC in order to develop our understanding of the benefits and advantages of using ToC. We also propose a checklist for reporting on the use of ToC to ensure transparent reporting and recommend that our checklist is used and refined by authors reporting the ToC approach.

  15. Development and Evaluation of a Cognitive Training Game for Older People: A Design-based Approach.

    Science.gov (United States)

    Lu, Ming-Hsin; Lin, Weijane; Yueh, Hsiu-Ping

    2017-01-01

    In the research field of cognitive aging, games have gained attention as training interventions to remediate age-related deficits. Cognitive training games on computer, video and mobile platforms have shown ample and positive support. However, the generalized effects are not agreed upon unanimously, and the game tasks are usually simple and decontextualized due to the limitations of measurements. This study adopted a qualitative approach of design-based research (DBR) to systematically review and pragmatically examine the regime, presentation and feedback design of a cognitive training game for older adults. An overview of the literature of cognitive aging and training games was conducted to form the theoretical conjectures of the design, and an iterative cycle and process were employed to develop a mobile game for older adults who are homebound or receiving care in a nursing home. Stakeholders, i.e., elderly users and institutional administrators, were invited to participate in the design process. Using two cycles of design and evaluation, a working prototype of an iPad-based app that accounted for the needs of elderly adults in terms of form, appearance and working function was developed and tested in the actual contexts of the participants' homes and an assisted living facility. The results showed that the cognitive training game developed in this study was accepted by the participants, and a high degree of satisfaction was noted. Moreover, the elements of the interface, including its size, layout and control flow, were tested and found to be suitable for use. This study contributes to the literature by providing design suggestions for such games, including the designs of the cognitive training structure, interface, interaction, instructions and feedback, based on empirical evidence collected in natural settings. This study further suggests that the effectiveness of cognitive training in mobile games be evaluated through field and physical testing on a larger

  16. Development and Evaluation of a Cognitive Training Game for Older People: A Design-based Approach

    Science.gov (United States)

    Lu, Ming-Hsin; Lin, Weijane; Yueh, Hsiu-Ping

    2017-01-01

    In the research field of cognitive aging, games have gained attention as training interventions to remediate age-related deficits. Cognitive training games on computer, video and mobile platforms have shown ample and positive support. However, the generalized effects are not agreed upon unanimously, and the game tasks are usually simple and decontextualized due to the limitations of measurements. This study adopted a qualitative approach of design-based research (DBR) to systematically review and pragmatically examine the regime, presentation and feedback design of a cognitive training game for older adults. An overview of the literature of cognitive aging and training games was conducted to form the theoretical conjectures of the design, and an iterative cycle and process were employed to develop a mobile game for older adults who are homebound or receiving care in a nursing home. Stakeholders, i.e., elderly users and institutional administrators, were invited to participate in the design process. Using two cycles of design and evaluation, a working prototype of an iPad-based app that accounted for the needs of elderly adults in terms of form, appearance and working function was developed and tested in the actual contexts of the participants' homes and an assisted living facility. The results showed that the cognitive training game developed in this study was accepted by the participants, and a high degree of satisfaction was noted. Moreover, the elements of the interface, including its size, layout and control flow, were tested and found to be suitable for use. This study contributes to the literature by providing design suggestions for such games, including the designs of the cognitive training structure, interface, interaction, instructions and feedback, based on empirical evidence collected in natural settings. This study further suggests that the effectiveness of cognitive training in mobile games be evaluated through field and physical testing on a larger

  17. Development and Evaluation of a Cognitive Training Game for Older People: A Design-based Approach

    Directory of Open Access Journals (Sweden)

    Ming-Hsin Lu

    2017-10-01

    Full Text Available In the research field of cognitive aging, games have gained attention as training interventions to remediate age-related deficits. Cognitive training games on computer, video and mobile platforms have shown ample and positive support. However, the generalized effects are not agreed upon unanimously, and the game tasks are usually simple and decontextualized due to the limitations of measurements. This study adopted a qualitative approach of design-based research (DBR to systematically review and pragmatically examine the regime, presentation and feedback design of a cognitive training game for older adults. An overview of the literature of cognitive aging and training games was conducted to form the theoretical conjectures of the design, and an iterative cycle and process were employed to develop a mobile game for older adults who are homebound or receiving care in a nursing home. Stakeholders, i.e., elderly users and institutional administrators, were invited to participate in the design process. Using two cycles of design and evaluation, a working prototype of an iPad-based app that accounted for the needs of elderly adults in terms of form, appearance and working function was developed and tested in the actual contexts of the participants' homes and an assisted living facility. The results showed that the cognitive training game developed in this study was accepted by the participants, and a high degree of satisfaction was noted. Moreover, the elements of the interface, including its size, layout and control flow, were tested and found to be suitable for use. This study contributes to the literature by providing design suggestions for such games, including the designs of the cognitive training structure, interface, interaction, instructions and feedback, based on empirical evidence collected in natural settings. This study further suggests that the effectiveness of cognitive training in mobile games be evaluated through field and physical

  18. EVALUATION OF STREET FURNITURE ACCORDING TO BASIC DESIGN PRINCIPLES

    OpenAIRE

    GHORAB, Peyman; YÜCEL CAYMAZ, Gökçen Firdevs

    2014-01-01

    In the urban context, it is important to create more comfortable and livable environments with proper planning, design and application. Because aesthetic considerations are of more importance today, designing urban furniture to give a more beautiful appearance to cities is of high priority; designers and those working in related disciplines must be careful to observe these principles throughout the design process. This paper describes research conducted to review the aesthetic principles invo...

  19. Collaborative design in education : evaluation of three approaches

    NARCIS (Netherlands)

    Leeuwen, van J.P.; Gassel, van F.J.M.; Otter, den A.F.H.J.; Duarte, J.P.; Sampaio, A.Z.

    2005-01-01

    Collaboration in design can take place in a physical, social space, in a distributed or virtual environment, or in a combination of both. Design teams use a range of ICT means to support both synchronous and asynchronous communication. While these tools are designed to facilitate collaboration, the

  20. Evaluation of vertical profiles to design continuous descent approach procedure

    Science.gov (United States)

    Pradeep, Priyank

    The current research focuses on predictability, variability and operational feasibility aspect of Continuous Descent Approach (CDA), which is among the key concepts of the Next Generation Air Transportation System (NextGen). The idle-thrust CDA is a fuel economical, noise and emission abatement procedure, but requires increased separation to accommodate for variability and uncertainties in vertical and speed profiles of arriving aircraft. Although a considerable amount of researches have been devoted to the estimation of potential benefits of the CDA, only few have attempted to explain the predictability, variability and operational feasibility aspect of CDA. The analytical equations derived using flight dynamics and Base of Aircraft and Data (BADA) Total Energy Model (TEM) in this research gives insight into dependency of vertical profile of CDA on various factors like wind speed and gradient, weight, aircraft type and configuration, thrust settings, atmospheric factors (deviation from ISA (DISA), pressure and density of the air) and descent speed profile. Application of the derived equations to idle-thrust CDA gives an insight into sensitivity of its vertical profile to multiple factors. This suggests fixed geometric flight path angle (FPA) CDA has higher degree of predictability and lesser variability at the cost of non-idle and low thrust engine settings. However, with optimized design this impact can be overall minimized. The CDA simulations were performed using Future ATM Concept Evaluation Tool (FACET) based on radar-track and aircraft type data (BADA) of the real air-traffic to some of the busiest airports in the USA (ATL, SFO and New York Metroplex (JFK, EWR and LGA)). The statistical analysis of the vertical profiles of CDA shows 1) mean geometric FPAs derived from various simulated vertical profiles are consistently shallower than 3° glideslope angle and 2) high level of variability in vertical profiles of idle-thrust CDA even in absence of

  1. The Correction of Myopia Evaluation Trial: lessons from the study design.

    Science.gov (United States)

    Hyman, L; Gwiazda, J

    2004-01-01

    The Correction of Myopia Evaluation Trial (COMET), a multicentre clinical trial based in 4 schools of optometry in the United States, evaluated the effect of progressive addition lenses versus single vision lenses on myopia progression in an ethnically diverse group of 469 myopic children aged 6 to 11 years. Completion of the clinical trial phase of the study provides an opportunity to evaluate aspects of the study design that contribute to its success. This article describes aspects of the study design that were influential in ensuring the smooth conduct of COMET. These include a dedicated team of investigators, an organisational structure with strong leadership and an independent Co-ordinating Centre, regular communication among investigators, flexible and creative approaches to recruitment and retention, sensitivity to concerns for child safety and child participation, and methods for enhancing and monitoring data reliability. The experience with COMET has provided a number of valuable lessons for all aspects of the study design that should benefit the development and implementation of future clinical trials, particularly those done in similar populations of children. The use of a carefully designed protocol using standard methods by dedicated members of the study team is essential in ensuring achievement of the study aims.

  2. Current status and perspective of multinational design evaluation program in Korea

    International Nuclear Information System (INIS)

    Sung, Key Yong

    2008-01-01

    The Multinational Design Evaluation Program (MDEP) is a multinational initiative to develop innovative approaches to leverage the resources and knowledge of the national regulatory authorities who will be tasked with the review of new reactor power plant designs. MDEP consisted of three stages: Stage 1 involved multilateral cooperation within existing regulatory frameworks; Stage 2 focused on enhanced multinational cooperation and convergence of codes, standards, and safety goals; and Stage 3 involved implementation of Stage 2 products to facilitate licensing processes for new reactors, including those being developed by the Generation IV International Forum. A year-long pilot project was initiated to assess the feasibility of the Stage 2 goals since October 2006. The main objective of Stage 2, as set in the Terms of Reference (ToR), was to establish reference regulatory practices and regulations to enhance the safety of new nuclear reactor designs. The convergence of regulatory practices and regulations associated with the reactor design reviews should allow for enhanced cooperation among regulators, improving the effectiveness and efficiency of the regulatory design reviews, which are part of each country's licensing process. This is expected to lead to a convergence of codes, standards and safety goals in the participating countries. To this end, a pilot project, consisting of two working groups, was launched. The first working group investigated the licensing basis for new nuclear reactor designs, the scope of design safety reviews and overall safety goals. The second examined regulatory oversight of components manufactured for new nuclear reactors

  3. Ergonomic design and evaluation of the handle for an endoscopic dissector.

    Science.gov (United States)

    Shimomura, Yoshihiro; Minowa, Keita; Kawahira, Hiroshi; Katsuura, Tetsuo

    2016-05-01

    The purpose of this study was to design an endoscopic dissector handle and objectively assess its usability. The handles were designed with increased contact area between the fingers and thumb and the eye rings, and the eye rings were modified to have a more perpendicular insertion angle to the finger midline. Four different handle models were compared, including a conventional product. Subjects performed dissection, exclusion, grasping, precision manipulation and precision handling tasks. Electromyography and subjective evaluations were measured. Compared to conventional handles, the designated handle reduced the muscle load in the extensor and flexor muscles of the forearm and increased subjective stability. The activity of the first dorsal interosseous muscle was sometimes influenced by the shape of the other parts. The ergonomically designed endoscopic dissector handle used in this study achieved high usability. Medical instrument designs based on ergonomic concepts should be assessed with objective indices. Practitioner Summary: The endoscopic dissector handles were designed with increased contact area and more suitable insertion angle between the fingers and thumb and the eye rings. Compared to conventional handles, the designated handle reduced the muscle load in the extensor and flexor muscles of the forearm and increased subjective stability.

  4. Health-economic evaluation in implant trials: design considerations.

    Science.gov (United States)

    Alt, Volker; Pavlidis, Theodoros; Szalay, Gabor; Heiss, Christian; Schnettler, Reinhard

    2009-01-01

    In today's world, demonstration of the safety, efficacy, and quality of a new treatment strategy is no longer sufficient in many countries for market entry and reimbursement in the public healthcare system. This implies that new implants in orthopedic and orthopedic trauma surgery not only must be shown to lead to better medical outcome compared with the standard of care implant, but also must be shown to exhibit "good value" for the money for the public health-care system based on sound economic data from health-economic studies. The purpose of this article is to elucidate a framework for health-economic aspects alongside implant trials, with the assumption that the new implant is more costly but potentially better than the control implant. Cost-effectiveness, cost-utility, and cost-benefit studies are suitable for the assessment of the health-economic value of a new implant. The following criteria should be considered for a health-economic study design in the context with an implant: i) it should state medical benefits of the new implant compared with the control implant; ii) it should precise the type of health economic study; iii) it should define the methodological approach, perspective of the study, and types of costs; iv) if necessary, it should state discount costs and/benefits; and v) a sound sensitivity analysis should be included. Furthermore, close cooperation between researchers, clinicians, and health economists is essential.

  5. Seismic design and evaluation criteria for DOE facilities (DOE-STD-1020-XX)

    International Nuclear Information System (INIS)

    Short, S.A.; Kennedy, R.P.; Murray, R.C.

    1993-01-01

    Seismic design and evaluation criteria for DOE facilities are provided in DOE-STD-1020-XX. The criteria include selection of design/evaluation seismic input from probabilistic seismic hazard curves combined with commonly practiced deterministic response evaluation methods and acceptance criteria with controlled levels of conservatism. Conservatism is intentionally introduced in specification of material strengths and capacities, in the allowance of limited inelastic behavior and by a seismic load factor. These criteria are based on the performance or risk goals specified in DOE 5480.28. Criteria have been developed following a graded approach for several performance goals ranging from that appropriate for normal-use facilities to that appropriate for facilities involving hazardous or critical operations. Performance goals are comprised of desired behavior and of the probability of not achieving that behavior. Following the seismic design/evaluation criteria of DOE-STD-1020-XX is sufficient to demonstrate that the probabilistic performance or risk goals are achieved. The criteria are simple procedures but with a sound, rigorous basis for the achievement of goals

  6. Human Factors Support in the Design and Evaluation of the Reactor Protection System Cabinet Operator Module

    International Nuclear Information System (INIS)

    Lee, Hyun Chul; Lee, Jung Woon

    2005-01-01

    A Korean project group, KNICS, is developing a new digitalized reactor protection system (RPS) and the developed system will be packaged into a cabinet with several racks. The cabinet of the RPS is used for the RPS function testing and monitoring by maintenance operators and is equipped with a flat panel display (FPD) with a touch screen capability as a main user interface for the RPS operation. This paper describes the human factors activities involved in the development process of the RPS: conceptual design, design guidance, and evaluation. The activities include a functional requirements analysis and task analysis, user interface style guide for the RPS cabinet operator module (COM), and a human factors evaluation through an experiment and questionnaires

  7. Designing and evaluating a persuasive child restraint television commercial.

    Science.gov (United States)

    Lewis, Ioni; Ho, Bonnie; Lennon, Alexia

    2016-01-01

    Relatively high rates of child restraint inappropriate use and misuse and faults in the installation of restraints have suggested a crucial need for public education messages to raise parental awareness of the need to use restraints correctly. This project involved the devising and pilot testing of message concepts, filming of a television advertisement (the TVC), and the evaluation of the TVC. This article focuses specifically upon the evaluation of the TVC. The development and evaluation of the TVC were guided by an extended theory of planned behavior that included the standard constructs of attitudes, subjective norms, and perceived behavioral control as well as the additional constructs of group norms and descriptive norms. The study also explored the extent to which parents with low and high intentions to self-check restraints differed on salient beliefs regarding the behavior. An online survey of parents (N = 384) was conducted where parents were randomly assigned to either the intervention group (n = 161), and therefore viewed the advertisement within the survey, or the control group (n = 223), and therefore did not view the advertisement. Following a one-off exposure to the TVC, the results indicated that, although not a significant difference, parents in the intervention group reported stronger intentions (M = 4.43, SD = 0.74) to self-check restraints than parents in the control group (M = 4.18, SD = 0.86). In addition, parents in the intervention group (M = 4.59, SD = 0.47) reported significantly higher levels of perceived behavioral control than parents in the control group (M = 4.40, SD = 0.73). The regression results revealed that, for parents in the intervention group, attitudes and group norms were significant predictors of parental intentions to self-check their child restraint. Finally, the exploratory analyses of parental beliefs suggested that those parents with low intentions to self-check child restraints were significantly more likely than

  8. Design evaluation in technology assessment: Illustrated by auditory impedance and sound distribution problems

    Science.gov (United States)

    Halldane, J. F.

    1972-01-01

    Technology is considered as a culture for changing a physical world and technology assessment questions the inherent cultural capability to modify power and material in support of living organisms. A comprehensive goal-parameter-synthesis-criterion specification is presented as a basis for a rational assessment of technology. The thesis queries the purpose of the assessed problems, the factors considered, the relationships between factors, and the values assigned those factors to accomplish the appropriate purpose. Stationary and sequential evaluation of enviro-organismic systems are delegated to the responsible personalities involved in design; from promoter/designer through contractor to occupant. Discussion includes design goals derived from organismic factors, definitions of human responses which establish viable criteria and relevant correlation models, linking stimulus parameters, and parallel problem-discipline centered design organization. A consistent concept of impedance, as a degradation in the performance of a specified parameter, is introduced to overcome the arbitrary inoperative connotations of terms like noise, discomfort, and glare. Applications of the evaluative specification are illustrated through design problems related to auditory impedance and sound distribution.

  9. Evaluation of the design effects of different agropastoral systems on the diversity and density of spiders

    Directory of Open Access Journals (Sweden)

    Melina S. Almada

    2017-04-01

    Full Text Available Sustainable agro-ecological design is challenging when the goal is self-regulation of the system. The objective of this study was to evaluate if the agropastoral design system affects the spider community, as spiders are the main predators in these production systems, and to determine those designs which maximize the diversity and density of spiders. The study was conducted during 2009/2010, at the Experimental Research Station of Agriculture (EEA-INTA Reconquista (Santa Fe, Argentina where we considered four different designs: C1 (five agricultural fields, C2 (three agricultural fields and four livestock fields, C3 (six agricultural fields and one livestock field and C4 (five agricultural fields and one forest area. In each design, the spiders were collected by pitfall traps and suction samples with a G-Vac (garden-vacuum. The designs proposed were considered on the basis of environmental heterogeneity. The C4 treatment had the greatest number of species, followed by C2, C3 and C1 (183, 178, 144 and 142 species, respectively, and C2 presented the greatest abundance of spiders followed by C4, C3 and C1 (n=5708, 4785, 4271 and 3448, respectively. Eight guilds were present in C3 and C4. This study is the first to evaluate the diversity of spiders in agropastoral systems in Argentina. Our results show that designs that include more fields with livestock or equal to those for agriculture, as well as forest areas, increase environmental heterogeneity. Therefore, the presence of a biological controller and dominant predatory group will be possible with sustainable designs that have environmental heterogeneity, contributing to improved pest control in agricultural systems.

  10. Cornell Alliance for Science Evaluation of Consensus on Genetically Modified Food Safety: Weaknesses in Study Design.

    Science.gov (United States)

    Antoniou, Michael N; Robinson, Claire J

    2017-01-01

    Cornell Alliance for Science has launched an initiative in which "citizen scientists" are called upon to evaluate studies on health risks of genetically modified (GM) crops and foods. The purpose is to establish whether the consensus on GM food safety claimed by the American Association for the Advancement of Science (AAAS) is supported by a review of the scientific literature. The Alliance's citizen scientists are examining more than 12,000 publication abstracts to quantify how far the scientific literature supports the AAAS's statement. We identify a number of fundamental weaknesses in the Alliance's study design, including evaluation is based only on information provided in the publication abstract; there is a lack of clarity as to what material is included in the 12,000 study abstracts to be reviewed, since the number of appropriately designed investigations addressing GM food safety are few; there is uncertainty as to whether studies of toxic effects arising from GM crop-associated pesticides will be included; there is a lack of clarity regarding whether divergent yet equally valid interpretations of the same study will be taken into account; and there is no definition of the cutoff point for consensus or non-consensus on GM food safety. In addition, vital industry proprietary biosafety data on GM crops and associated pesticides are not publicly available and is thus cannot inform this project. Based on these weaknesses in the study design, we believe it is questionable as to whether any objective or meaningful conclusion can be drawn from the Alliance's initiative.

  11. First results of the wind evaluation breadboard for ELT primary mirror design

    Science.gov (United States)

    Reyes García-Talavera, Marcos; Viera, Teodora; Núñez, Miguel

    2010-07-01

    The Wind Evaluation Breadboard (WEB) is a primary mirror and telescope simulator formed by seven aluminium segments, including position sensors, electromechanical support systems and support structures. WEB has been developed to evaluate technologies for primary mirror wavefront control and to evaluate the performance of the control of wind buffeting disturbance on ELT segmented mirrors. For this purpose WEB electro-mechanical set-up simulates the real operational constrains applied to large segmented mirrors. This paper describes the WEB assembly, integration and verification, the instrument characterisation and close loop control design, including the dynamical characterization of the instrument and the control architecture. The performance of the new technologies developed for position sensing, acting and controlling is evaluated. The integration of the instrument in the observatory and the results of the first experiments are summarised, with different wind conditions, elevation and azimuth angles of incidence. Conclusions are extracted with respect the wind rejection performance and the control strategy for an ELT. WEB has been designed and developed by IAC, ESO, ALTRAN and JUPASA, with the integration of subsystems of FOGALE and TNO.

  12. Human-Automation Integration: Principle and Method for Design and Evaluation

    Science.gov (United States)

    Billman, Dorrit; Feary, Michael

    2012-01-01

    Future space missions will increasingly depend on integration of complex engineered systems with their human operators. It is important to ensure that the systems that are designed and developed do a good job of supporting the needs of the work domain. Our research investigates methods for needs analysis. We included analysis of work products (plans for regulation of the space station) as well as work processes (tasks using current software), in a case study of Attitude Determination and Control Officers (ADCO) planning work. This allows comparing how well different designs match the structure of the work to be supported. Redesigned planning software that better matches the structure of work was developed and experimentally assessed. The new prototype enabled substantially faster and more accurate performance in plan revision tasks. This success suggests the approach to needs assessment and use in design and evaluation is promising, and merits investigatation in future research.

  13. Seismic site evaluation practice and seismic design guide for NPP in Continent of China

    Energy Technology Data Exchange (ETDEWEB)

    Yuxian, Hu [State Seismological Bureau, Beijing, BJ (China). Inst. of Geophysics

    1997-03-01

    Energy resources, seismicity, NPP and related regulations of the Continent of China are briefly introduced in the beginning and two codes related to the seismic design of NPP, one on siting and another on design, are discussed in some detail. The one on siting is an official code of the State Seismological Bureau, which specifies the seismic safety evaluation requirements of various kinds of structures, from the most critic and important structures such as NPP to ordinary buildings, and including also engineering works in big cities. The one on seismic design of NPP is a draft subjected to publication now, which will be an official national code. The first one is somewhat unique but the second one is quite similar to those in the world. (author)

  14. Seismic site evaluation practice and seismic design guide for NPP in Continent of China

    International Nuclear Information System (INIS)

    Hu Yuxian

    1997-01-01

    Energy resources, seismicity, NPP and related regulations of the Continent of China are briefly introduced in the beginning and two codes related to the seismic design of NPP, one on siting and another on design, are discussed in some detail. The one on siting is an official code of the State Seismological Bureau, which specifies the seismic safety evaluation requirements of various kinds of structures, from the most critic and important structures such as NPP to ordinary buildings, and including also engineering works in big cities. The one on seismic design of NPP is a draft subjected to publication now, which will be an official national code. The first one is somewhat unique but the second one is quite similar to those in the world. (author)

  15. A Design for the Evaluation of Management Information Systems.

    Science.gov (United States)

    Spuck, Dennis W.; Bozeman, William C.

    1980-01-01

    This paper has presented a model for the evaluation of management information systems. The three levels of information considered were actual, perceptual, and attitudinal. The dimensions of evaluation discussed were function, utilization, and effects. (Author/IRT)

  16. Reliability Evaluation and Probabilistic Design of Coastal Structures

    DEFF Research Database (Denmark)

    Burcharth, H. F.

    1993-01-01

    Conventional design practice for coastal structures is deterministic in nature and is based on the concept of a design load, which should not exceed the resistance (carrying capacity) of the structure. The design load is usually defined on a probabilistic basis as a characteristic value of the load......, e.g. the expectation (mean) value of the lOO-year return period event, however, often without consideration of the involved uncertainties. The resistance is in most cases defined in terms of the load which causes a certain design impact or damage to the structure and is not given as an ultimate...... force or deformation. This is because most of the available design formulae only give the relationship between wave characteristics and structural response, e.g. in terms of run-up, overtopping, armour layer damage etc. An example is the Hudson formula for armour layer stability. Almost all such design...

  17. Mission Trade Space Evaluation through Multiphysics Design and Optimization

    Data.gov (United States)

    National Aeronautics and Space Administration — In recent years, modeling and simulation tools have enabled engineers to design highly complex systems while taking into consideration constraints across multiple...

  18. Evaluating the implementation and impacts of middle grades inquiry-based engineering design modules

    Science.gov (United States)

    Harlan, Jessica M.

    . When reviewing the assessment's evidence base, we found no published literature regarding the assessment's psychometric properties. We found that the AWE Work Values scale assesses two separate sets of occupational values: 1) using analytical and problem solving skills and 2) personal satisfaction. In Chapter 5, I discuss the implications of the research presented in these articles to the field of integrated STEM. This includes a need to further develop and test tools and methods for measuring program impact. While the articles address several issues related to research and evaluation within the context of K-12 integrated STEM education, the concepts and implications also apply to the general field of instructional design. The primary lesson is the need to systematically evaluate designed instruction, including measuring fidelity of implementation and designing evaluations in advance to ensure appropriate data are gathered. Recommendations for future research include identification of common outcomes for integrated STEM, psychometric testing of integrated STEM attitude measures, impacts of other factors such as interest in STEM, and development and testing of instructional design models for integrated STEM.

  19. Evaluation of a New Remote Handling Design for High Throughput Annular Centrifugal Contactors

    International Nuclear Information System (INIS)

    Meikrantz, David H.; Garn, Troy G.; Law, Jack D.; Macaluso, Lawrence L.

    2009-01-01

    Advanced designs of nuclear fuel recycling plants are expected to include more ambitious goals for aqueous based separations including; higher separations efficiency, high-level waste minimization, and a greater focus on continuous processes to minimize cost and footprint. Therefore, Annular Centrifugal Contactors (ACCs) are destined to play a more important role for such future processing schemes. Previous efforts defined and characterized the performance of commercial 5 cm and 12.5 cm single-stage ACCs in a 'cold' environment. The next logical step, the design and evaluation of remote capable pilot scale ACCs in a 'hot' or radioactive environment was reported earlier. This report includes the development of remote designs for ACCs that can process the large throughput rates needed in future nuclear fuel recycling plants. Novel designs were developed for the remote interconnection of contactor units, clean-in-place and drain connections, and a new solids removal collection chamber. A three stage, 12.5 cm diameter rotor module has been constructed and evaluated for operational function and remote handling in highly radioactive environments. This design is scalable to commercial CINC ACC models from V-05 to V-20 with total throughput rates ranging from 20 to 650 liters per minute. The V-05R three stage prototype was manufactured by the commercial vendor for ACCs in the U.S., CINC mfg. It employs three standard V-05 clean-in-place (CIP) units modified for remote service and replacement via new methods of connection for solution inlets, outlets, drain and CIP. Hydraulic testing and functional checks were successfully conducted and then the prototype was evaluated for remote handling and maintenance suitability. Removal and replacement of the center position V-05R ACC unit in the three stage prototype was demonstrated using an overhead rail mounted PaR manipulator. This evaluation confirmed the efficacy of this innovative design for interconnecting and cleaning

  20. Implementation and evaluation of LMS mobile application: scele mobile based on user-centered design

    Science.gov (United States)

    Banimahendra, R. D.; Santoso, H. B.

    2018-03-01

    The development of mobile technology is now increasing rapidly, demanding all activities including learning should be done on mobile devices. It shows that the implementation of mobile application as a learning medium needs to be done. This study describes the process of developing and evaluating the Moodle-based mobile Learning Management System (LMS) application called Student Centered e-Learning Environment (SCeLE). This study discusses the process of defining features, implementing features into the application, and evaluating the application. We define the features using user research and literature study, then we implement the application with user-centered design basis, at the last phase we evaluated the application using usability testing and system usability score (SUS). The purpose of this study is to determine the extent to which this application can help the users doing their tasks and provide recommendation for the next research and development.

  1. DOE (Department of Energy) natural phenomena guidelines flood design and evaluation

    International Nuclear Information System (INIS)

    McCann, M.W.; Savy, J.B.

    1989-01-01

    Design and evaluation guidelines for DOE (Department of Energy) facilities subjected to earthquake, wind/tornado, and flood have been developed and presented in UCRL-15910 (Ref.1). This paper summarizes Chapter 6 of UCRL-15910 describing the philosophy and procedures for the design or evaluation of facilities for flood. The flood design and evaluation guidelines seek to ensure that DOE facilities satisfy the performance goals described in UCRL-15910. The guidelines are applicable to new and existing construction; however, in the evaluation of existing facilities, fewer design options may be available to satisfy the performance goals. Evaluation of the flood design for a facility consists of: (1) defining the design basis flood (DBFL), (2) evaluating site conditions (e.g., facility location, location of openings and doorways), and (3) assessing flood design strategies (e.g., build above DBFL levels, harden the site)

  2. Comparative Ergonomic Evaluation of Spacesuit and Space Vehicle Design

    Science.gov (United States)

    England, Scott; Cowley, Matthew; Benson, Elizabeth; Harvill, Lauren; Blackledge, Christopher; Perez, Esau; Rajulu, Sudhakar

    2012-01-01

    With the advent of the latest human spaceflight objectives, a series of prototype architectures for a new launch and reentry spacesuit that would be suited to the new mission goals. Four prototype suits were evaluated to compare their performance and enable the selection of the preferred suit components and designs. A consolidated approach to testing was taken: concurrently collecting suit mobility data, seat-suit-vehicle interface clearances, and qualitative assessments of suit performance within the volume of a Multi-Purpose Crew Vehicle mockup. It was necessary to maintain high fidelity in a mockup and use advanced motion-capture technologies in order to achieve the objectives of the study. These seemingly mutually exclusive goals were accommodated with the construction of an optically transparent and fully adjustable frame mockup. The construction of the mockup was such that it could be dimensionally validated rapidly with the motioncapture system. This paper describes the method used to create a space vehicle mockup compatible with use of an optical motion-capture system, the consolidated approach for evaluating spacesuits in action, and a way to use the complex data set resulting from a limited number of test subjects to generate hardware requirements for an entire population. Kinematics, hardware clearance, anthropometry (suited and unsuited), and subjective feedback data were recorded on 15 unsuited and 5 suited subjects. Unsuited subjects were selected chiefly based on their anthropometry in an attempt to find subjects who fell within predefined criteria for medium male, large male, and small female subjects. The suited subjects were selected as a subset of the unsuited medium male subjects and were tested in both unpressurized and pressurized conditions. The prototype spacesuits were each fabricated in a single size to accommodate an approximately average-sized male, so select findings from the suit testing were systematically extrapolated to the extremes

  3. Economic evaluation of angiographic interventions including a whole-radiology in- and outpatient care; Wirtschaftliche Evaluation angiographischer Interventionen einschliesslich einer radiologischen stationaeren und ambulanten Patientenbetreuung

    Energy Technology Data Exchange (ETDEWEB)

    Nolte-Ernsting, C.; Abel, K.; Krupski, G.; Lorenzen, J.; Adam, G. [Klinik und Poliklinik fuer Diagnostische und Interventionelle Radiologie, Universitaetsklinikum Hamburg-Eppendorf (Germany)

    2006-01-01

    Purpose: To determine the economic efficiency of a whole-radiology in- and outpatient treatment with angiographic interventions performed as the main or sole therapy. Materials and Methods: The calculations represent the data of a university radiology department, including the following angiographic interventions (neuroradiology not considered): Vascular intervention (PTA, stent implantation) of kidneys and extremities, recanalization of hemodialysis access, chemoembolization, diagnostic arterioportal liver CT, port implantation, varicocele embolization, PTCD, percutaneous implantation of biliary stent. First, the different angiographic interventions are categorized with reference to the German DRG system 2005. Considering the example of a university hospital, the individual cost of each intervention is calculated and correlated with reimbursements by G-DRG2005 and so-called ''ambulant operation'' (EBM200plus). With these data, profits and losses are calculated for both in- and outpatient care. Results: Radiologic interventions of inpatients yield a profit in the majority of cases. With a base rate of 2900 Euro, the profits in our university hospital range between -872 Euro and +3411 Euro (mean: +1348 Euro). On the other hand, those angiographic interventions suitable for ''ambulant operation'' generate average profits of +372 Euro, if only direct costs are considered. The data of outpatient radiological interventions average between 381 Euro up to 1612 Euro lower than compared with profits obtained from in patient care. (orig.)

  4. A multiobjective decision support/numerical modeling approach for design and evaluation of shallow landfill burial systems

    Energy Technology Data Exchange (ETDEWEB)

    Ascough, II, James Clifford [Purdue Univ., Lafayette, IN (United States)

    1992-05-01

    The capability to objectively evaluate design performance of shallow landfill burial (SLB) systems is of great interest to diverse scientific disciplines, including hydrologists, engineers, environmental scientists, and SLB regulators. The goal of this work was to develop and validate a procedure for the nonsubjective evaluation of SLB designs under actual or simulated environmental conditions. A multiobjective decision module (MDM) based on scoring functions (Wymore, 1988) was implemented to evaluate SLB design performance. Input values to the MDM are provided by hydrologic models. The MDM assigns a total score to each SLB design alternative, thereby allowing for rapid and repeatable design performance evaluation. The MDM was validated for a wide range of SLB designs under different climatic conditions. Rigorous assessment of SLB performance also requires incorporation of hydrologic probabilistic analysis and hydrologic risk into the overall design. This was accomplished through the development of a frequency analysis module. The frequency analysis module allows SLB design event magnitudes to be calculated based on the hydrologic return period. The multiobjective decision and freqeuncy anslysis modules were integrated in a decision support system (DSS) framework, SLEUTH (Shallow Landfill Evaluation Using Transport and Hydrology). SLEUTH is a Microsoft Windows {trademark} application, and is written in the Knowledge Pro Windows (Knowledge Garden, Inc., 1991) development language.

  5. A multiobjective decision support/numerical modeling approach for design and evaluation of shallow landfill burial systems

    International Nuclear Information System (INIS)

    Ascough, J.C. II

    1992-05-01

    The capability to objectively evaluate design performance of shallow landfill burial (SLB) systems is of great interest to diverse scientific disciplines, including hydrologists, engineers, environmental scientists, and SLB regulators. The goal of this work was to develop and validate a procedure for the nonsubjective evaluation of SLB designs under actual or simulated environmental conditions. A multiobjective decision module (MDM) based on scoring functions (Wymore, 1988) was implemented to evaluate SLB design performance. Input values to the MDM are provided by hydrologic models. The MDM assigns a total score to each SLB design alternative, thereby allowing for rapid and repeatable design performance evaluation. The MDM was validated for a wide range of SLB designs under different climatic conditions. Rigorous assessment of SLB performance also requires incorporation of hydrologic probabilistic analysis and hydrologic risk into the overall design. This was accomplished through the development of a frequency analysis module. The frequency analysis module allows SLB design event magnitudes to be calculated based on the hydrologic return period. The multiobjective decision and freqeuncy anslysis modules were integrated in a decision support system (DSS) framework, SLEUTH (Shallow Landfill Evaluation Using Transport and Hydrology). SLEUTH is a Microsoft Windows trademark application, and is written in the Knowledge Pro Windows (Knowledge Garden, Inc., 1991) development language

  6. Coal gasification systems engineering and analysis. Appendix G: Commercial design and technology evaluation

    Science.gov (United States)

    1980-01-01

    A technology evaluation of five coal gasifier systems (Koppers-Totzek, Texaco, Babcock and Wilcox, Lurgi and BGC/Lurgi) and procedures and criteria for evaluating competitive commercial coal gasification designs is presented. The technology evaluation is based upon the plant designs and cost estimates developed by the BDM-Mittelhauser team.

  7. Evaluation of radiation protection in x rays room design in diagnostic radiography department in Omdurman locality

    International Nuclear Information System (INIS)

    Adam, Ahmed yusif Abdelrahman

    2013-03-01

    The purpose of this study is conducted in order to evaluate the application of radiation protection in x-ray rooms design in diagnosis radiology department, evaluate personal monitoring devices, to assess primary scatter and leakage radiation dose, to assess monitoring devices if available, in period from March 2013 to August 2013. The design data included room size, control room size, manufacture of equipment, room surrounding areas, workload of all equipment rooms, type of x-ray equipment, radiation worker's in all hospital, number of patient in each shift, structural material and shielding, K vp and m As used in x-ray room department during examination testing. The results of this study show that there is x-ray room design, the design of x-ray equipment is accepted according to the radiation safety institute team of quality control. Also the study shows that the radiation protection devices are available and in a good condition and enough in number. The study shows that there are not personal monitoring devices and services. the radiological technologist are well trained. Also the study investigation the radiation protection in x-ray room in diagnostic department in Omdurman locality. Finally the study shows that there is compact able to ICRP recommended and National quality control in Sudan Atomic Energy Council exception, Alwedad, Abusied and Blue Nile there are have not control room concludes that there is only in relationship hospital have a window without shield.(Author)

  8. Design and evaluation of a new exoskeleton for gait rehabilitation

    Directory of Open Access Journals (Sweden)

    I. D. Geonea

    2017-10-01

    Full Text Available This work addresses the design and numerical characterization of a new exoskeleton solution for human leg motion assistance and rehabilitation. The exoskeleton solution is anthropomorphic, simple, low cost and easy to adapt on the human subject. The design aspect concerns the exoskeleton mechatronic structure, achieved in SolidWorks virtual environment. Numerical simulation is performed in MSC.ADAMS simulation environment. Obtained results for the exoskeleton computed motion are compared with those obtained from experimental walking of healthy subject. The prototype feasibility is studied both for design and operation aspect.

  9. The Design, Development, and Evaluation of a Qualitative Data Collection Application for Pregnant Women.

    Science.gov (United States)

    Keedle, Hazel; Schmied, Virginia; Burns, Elaine; Dahlen, Hannah

    2018-01-01

    This article explores the development and evaluation of a smartphone mobile software application (app) to collect qualitative data. The app was specifically designed to capture real-time qualitative data from women planning a vaginal birth after caesarean delivery. This article outlines the design and development of the app to include funding, ethics, and the recruitment of an app developer, as well as the evaluation of using the app by seven participants. Data collection methods used in qualitative research include interviews and focus groups (either online, face-to-face, or by phone), participant diaries, or observations of interactions. This article identifies an alternative data collection methodology using a smartphone app to collect real-time data. The app provides real-time data and instant access to data alongside the ability to access participants from a variety of locations. This allows the researcher to gain insight into the experiences of participants through audio or video recordings in longitudinal studies without the need for constant interactions or interviews with participants. Using smartphone applications can allow researchers to access participants who are traditionally hard to reach and access their data in real time. Evaluating these apps before use in research is invaluable. © 2017 Sigma Theta Tau International.

  10. COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

    NARCIS (Netherlands)

    DUINEVELD, CAA; SMILDE, AK; DOORNBOS, DA

    The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

  11. COMPARISON OF EXPERIMENTAL-DESIGNS COMBINING PROCESS AND MIXTURE VARIABLES .1. DESIGN CONSTRUCTION AND THEORETICAL EVALUATION

    NARCIS (Netherlands)

    DUINEVELD, C. A. A.; Smilde, A. K.; Doornbos, D. A.

    1993-01-01

    The combination of process variables and mixture variables in experimental design is a problem which has not yet been solved. It is examined here whether a set of designs can be found which can be used for a series of models of reasonable complexity. The proposed designs are compared with known

  12. Meta-analysis of the INSIG2 association with obesity including 74,345 individuals: does heterogeneity of estimates relate to study design?

    DEFF Research Database (Denmark)

    Heid, Iris M; Huth, Cornelia; Loos, Ruth J F

    2009-01-01

    with subjects selected for conditions related to a better health status ('healthy population', HP), and obesity studies (OB). We tested five hypotheses to explore potential sources of heterogeneity. The meta-analysis of 27 studies on Caucasian adults (n = 66,213) combining the different study designs did......The INSIG2 rs7566605 polymorphism was identified for obesity (BMI> or =30 kg/m(2)) in one of the first genome-wide association studies, but replications were inconsistent. We collected statistics from 34 studies (n = 74,345), including general population (GP) studies, population-based studies...... not support overall association of the CC-genotype with obesity, yielding an odds ratio (OR) of 1.05 (p-value = 0.27). The I(2) measure of 41% (p-value = 0.015) indicated between-study heterogeneity. Restricting to GP studies resulted in a declined I(2) measure of 11% (p-value = 0.33) and an OR of 1.10 (p...

  13. design, construction and performance evaluation of multiple casting

    African Journals Online (AJOL)

    eobe

    time taken for solidification, plays an important role in the casting. There should not ... Keywords: Design, Construction, Multiple casting machine, Compo Casting operation. 1. Introduction .... metal and pathway channel pipe with heater is used.

  14. design, construction and evaluation of a vertical plate maize seed ...

    African Journals Online (AJOL)

    user

    flow types do not meter individual seeds but rather a consistent volume of .... furrow opener design was mild steel angle iron of ... and required strength and reliability and readily available ..... Bharat, M. R. and Sidharth, D., "Tire modelling.

  15. Lagoa Real design. Description and evaluation of sampling system

    International Nuclear Information System (INIS)

    Hashizume, B.K.

    1982-10-01

    This report describes the samples preparation system of drilling from Lagoa Real Design, aiming obtainment representative fraction of the half from drilling outlier. The error of sampling + analysis and analytical accuracy was obtainment by delayed neutron analysis. (author)

  16. Human factors issues and approaches in the spatial layout of a space station control room, including the use of virtual reality as a design analysis tool

    Science.gov (United States)

    Hale, Joseph P., II

    1994-01-01

    Human Factors Engineering support was provided for the 30% design review of the late Space Station Freedom Payload Control Area (PCA). The PCA was to be the payload operations control room, analogous to the Spacelab Payload Operations Control Center (POCC). This effort began with a systematic collection and refinement of the relevant requirements driving the spatial layout of the consoles and PCA. This information was used as input for specialized human factors analytical tools and techniques in the design and design analysis activities. Design concepts and configuration options were developed and reviewed using sketches, 2-D Computer-Aided Design (CAD) drawings, and immersive Virtual Reality (VR) mockups.

  17. Design of the integration interface between the EU HCPB TBM and the ITER TBM port plug including hot cell operations for connection

    International Nuclear Information System (INIS)

    Neuberger, H.; Boccaccini, L.V.; Roccella, R.

    2007-01-01

    In the frame of the activities of the EU Breeder Blanket Programme and of the Test Blanket Working Group, the Helium Cooled Pebble Bed Test Blanket Module- (HCPB-TBM) System is developed. The TBM test schedule foresees four different campaigns for simulation of DEMO relevant conditions, campaign requires a dedicate TBM. Therefore a concept for TBM integration into ITER is designed with attention to simplify the mounting/dismounting operations. This paper presents the status of this concept with regard to the operations in hot cell required to install a new TBM into an equatorial TBM Port Plug (PP). This includes the establishment of the connection for the attachment, supply- and diagnostic lines in the environment of the interface (IF 1) between the TBM rear part and the PP backside shield. The connection of IF 1 has to be designed to cope with a temperature difference between TBM and PP (∝200 K) and the EM-loads during normal operation and disruption scenarios. The reference attachment concept based on shear keys and flexible cartridges is revised to cope with new conditions on the load and at the interface to the PP. According to the latest results of EM analysis, a radial component of the Maxwell forces (due to the ferromagnetic structural material) has been identified as an additional challenging load for the attachment. Furthermore, the replacing operations at IF 1 are influenced by the design of the PP; the recent ITER proposal based on a removable back side shield allows access to the IF 1 from the periphery after the frame of the PP surrounding the TBM is removed. As for the mechanical attachment, the tools and operations for connection of the TBM supply lines (Helium-, Purge- and measurement lines for different purpose depending on the test schedule) are strongly influenced by the restrictions to access IF 1, too. Dismantling of the frame would allow direct access to the interface by e.g. orbital welding tools. The concept for connection of the TBM

  18. Robustness-based evaluation of hydropower infrastructure design under climate change

    Directory of Open Access Journals (Sweden)

    Mehmet Ümit Taner

    2017-01-01

    Full Text Available The conventional tools of decision-making in water resources infrastructure planning have been developed for problems with well-characterized uncertainties and are ill-suited for problems involving climate nonstationarity. In the past 20 years, a predict-then-act-based approach to the incorporation of climate nonstationarity has been widely adopted in which the outputs of bias-corrected climate model projections are used to evaluate planning options. However, the ambiguous nature of results has often proved unsatisfying to decision makers. This paper presents the use of a bottom-up, decision scaling framework for the evaluation of water resources infrastructure design alternatives regarding their robustness to climate change and expected value of performance. The analysis begins with an assessment of the vulnerability of the alternative designs under a wide domain of systematically-generated plausible future climates and utilizes downscaled climate projections ex post to inform likelihoods within a risk-based evaluation. The outcomes under different project designs are compared by way of a set of decision criteria, including the performance under the most likely future, expected value of performance across all evaluated futures and robustness. The method is demonstrated for the design of a hydropower system in sub-Saharan Africa and is compared to the results that would be found using a GCM-based, scenario-led analysis. The results indicate that recommendations from the decision scaling analysis can be substantially different from the scenario-led approach, alleviate common shortcomings related to the use of climate projections in water resources planning, and produce recommendations that are more robust to future climate uncertainty.

  19. Design, fabrication and evaluation of fish meal pelletizing machine ...

    African Journals Online (AJOL)

    A 113.1kg/h fish meal pellet processing machine which produced 4mm diameter pellet, with an average length of 6mm was designed and fabricated. Design values of 210 was used for the maximum angle that the hopper wall formed with the vertical in the discharge zone, a critical stress of 1.3kPa of the ground particulate ...

  20. Developing a weighting strategy to include mobile phone numbers into an ongoing population health survey using an overlapping dual-frame design with limited benchmark information.

    Science.gov (United States)

    Barr, Margo L; Ferguson, Raymond A; Hughes, Phil J; Steel, David G

    2014-09-04

    In 2012 mobile phone numbers were included into the ongoing New South Wales Population Health Survey (NSWPHS) using an overlapping dual-frame design. Previously in the NSWPHS the sample was selected using random digit dialing (RDD) of landline phone numbers. The survey was undertaken using computer assisted telephone interviewing (CATI). The weighting strategy needed to be significantly expanded to manage the differing probabilities of selection by frame, including that of children of mobile-only phone users, and to adjust for the increased chance of selection of dual-phone users. This paper describes the development of the final weighting strategy to properly combine the data from two overlapping sample frames accounting for the fact that population benchmarks for the different sampling frames were not available at the state or regional level. Estimates of the number of phone numbers for the landline and mobile phone frames used to calculate the differing probabilities of selection by frame, for New South Wales (NSW) and by stratum, were obtained by apportioning Australian estimates as none were available for NSW. The weighting strategy was then developed by calculating person selection probabilities, selection weights, applying a constant composite factor to the dual-phone users sample weights, and benchmarking to the latest NSW population by age group, sex and stratum. Data from the NSWPHS for the first quarter of 2012 was used to test the weighting strategy. This consisted of data on 3395 respondents with 2171 (64%) from the landline frame and 1224 (36%) from the mobile frame. However, in order to calculate the weights, data needed to be available for all core weighting variables and so 3378 respondents, 2933 adults and 445 children, had sufficient data to be included. Average person weights were 3.3 times higher for the mobile-only respondents, 1.3 times higher for the landline-only respondents and 1.7 times higher for dual-phone users in the mobile frame

  1. Integrated Computer-aided Framework for Sustainable Chemical Product Design and Evaluation

    DEFF Research Database (Denmark)

    Kalakul, Sawitree; Cignitti, Stefano; Zhang, Lei

    2016-01-01

    This work proposes an integrated model-based framework for chemical product design and evaluation based on which the software, VPPD-Lab (The Virtual Product-Process Design Laboratory) has been developed. The framework allows the following options: (1) design a product using design templates...

  2. [Design of standard voice sample text for subjective auditory perceptual evaluation of voice disorders].

    Science.gov (United States)

    Li, Jin-rang; Sun, Yan-yan; Xu, Wen

    2010-09-01

    To design a speech voice sample text with all phonemes in Mandarin for subjective auditory perceptual evaluation of voice disorders. The principles for design of a speech voice sample text are: The short text should include the 21 initials and 39 finals, this may cover all the phonemes in Mandarin. Also, the short text should have some meanings. A short text was made out. It had 155 Chinese words, and included 21 initials and 38 finals (the final, ê, was not included because it was rarely used in Mandarin). Also, the text covered 17 light tones and one "Erhua". The constituent ratios of the initials and finals presented in this short text were statistically similar as those in Mandarin according to the method of similarity of the sample and population (r = 0.742, P text were statistically not similar as those in Mandarin (r = 0.731, P > 0.05). A speech voice sample text with all phonemes in Mandarin was made out. The constituent ratios of the initials and finals presented in this short text are similar as those in Mandarin. Its value for subjective auditory perceptual evaluation of voice disorders need further study.

  3. Sampling and energy evaluation challenges in ligand binding protein design.

    Science.gov (United States)

    Dou, Jiayi; Doyle, Lindsey; Jr Greisen, Per; Schena, Alberto; Park, Hahnbeom; Johnsson, Kai; Stoddard, Barry L; Baker, David

    2017-12-01

    The steroid hormone 17α-hydroxylprogesterone (17-OHP) is a biomarker for congenital adrenal hyperplasia and hence there is considerable interest in development of sensors for this compound. We used computational protein design to generate protein models with binding sites for 17-OHP containing an extended, nonpolar, shape-complementary binding pocket for the four-ring core of the compound, and hydrogen bonding residues at the base of the pocket to interact with carbonyl and hydroxyl groups at the more polar end of the ligand. Eight of 16 designed proteins experimentally tested bind 17-OHP with micromolar affinity. A co-crystal structure of one of the designs revealed that 17-OHP is rotated 180° around a pseudo-two-fold axis in the compound and displays multiple binding modes within the pocket, while still interacting with all of the designed residues in the engineered site. Subsequent rounds of mutagenesis and binding selection improved the ligand affinity to nanomolar range, while appearing to constrain the ligand to a single bound conformation that maintains the same "flipped" orientation relative to the original design. We trace the discrepancy in the design calculations to two sources: first, a failure to model subtle backbone changes which alter the distribution of sidechain rotameric states and second, an underestimation of the energetic cost of desolvating the carbonyl and hydroxyl groups of the ligand. The difference between design model and crystal structure thus arises from both sampling limitations and energy function inaccuracies that are exacerbated by the near two-fold symmetry of the molecule. © 2017 The Authors Protein Science published by Wiley Periodicals, Inc. on behalf of The Protein Society.

  4. Work-Centered Design and Evaluation of a C2 Visualization Aid

    National Research Council Canada - National Science Library

    Roth, Emilie; Scott, Ronald; Kazmierczak, Tom; Whitaker, Randall; Stilson, Mona; Thomas-Meyers, Gina; Wampler, Jeffrey

    2006-01-01

    .... We have been developing and applying work-centered design and evaluation methodologies to design advanced visualization and support tools intended to more effectively support C2 cognitive and collaborative work...

  5. Experimental Evaluation of Three Designs of Electrodynamic Flexural Transducers

    Directory of Open Access Journals (Sweden)

    Tobias J. R. Eriksson

    2016-08-01

    Full Text Available Three designs for electrodynamic flexural transducers (EDFT for air-coupled ultrasonics are presented and compared. An all-metal housing was used for robustness, which makes the designs more suitable for industrial applications. The housing is designed such that there is a thin metal plate at the front, with a fundamental flexural vibration mode at ∼50 kHz. By using a flexural resonance mode, good coupling to the load medium was achieved without the use of matching layers. The front radiating plate is actuated electrodynamically by a spiral coil inside the transducer, which produces an induced magnetic field when an AC current is applied to it. The transducers operate without the use of piezoelectric materials, which can simplify manufacturing and prolong the lifetime of the transducers, as well as open up possibilities for high-temperature applications. The results show that different designs perform best for the generation and reception of ultrasound. All three designs produced large acoustic pressure outputs, with a recorded sound pressure level (SPL above 120 dB at a 40 cm distance from the highest output transducer. The sensitivity of the transducers was low, however, with single shot signal-to-noise ratio ( SNR ≃ 15 dB in transmit–receive mode, with transmitter and receiver 40 cm apart.

  6. How Store Design Affect the Consumer Evaluation of Fashion Items

    DEFF Research Database (Denmark)

    Münster, Mia Borch; Kristensen, Tore; Gabrielsen, Gorm

    specially designed to match the style of each sub-brand. The interiors of the three shops are analysed and compared. To study the individual responses, data were collected on an iPad using a method building on paired comparisons. The experiment shows how 40 participants rate six products in three different...... shops, and in some cases the study of the room and the product made a surprising match. The results show that the products were not rated higher when presented in the interior designed for the specific sub-brand. However, when looking at the favourite products of the participants, it turned out...... that the majority of the highly rated products were given in one specific room, which does simply that the interior design influenced the consumers when rating their favourite products....

  7. Operator model-based design and evaluation of advanced systems

    International Nuclear Information System (INIS)

    Schryver, J.C.

    1988-01-01

    A multi-level operator modeling approach is recommended to provide broad support for the integrated design of advanced control and protection systems for new nuclear power plants. Preliminary design should address the symbiosis of automated systems and human operator by giving careful attention to the roles assigned to these two system elements. A conceptual model of the operator role is developed in the context of a command control-communication problem. According to this approach, joint responsibility can be realized in at least two ways: sharing or allocation. The inherent stabilities of different regions of the operator role space are considered

  8. Fatigue data compilation and evaluation of fatigue on design

    International Nuclear Information System (INIS)

    Nyilas, A.

    1985-05-01

    The aim of this report is a review of the available fatigue data of various materials necessary for the design of large superconducting magnets for fusion. One of the primary objectives of this work is to present a broad outline of the low temperature fatigue data of relevant materials within the scope of available data. Besides the classical fatigue data of materials the fatigue crack propagation measurements are outlined widely. The existing recommendations for the design of cryogenic structures are described. A brief introduction of fracture mechanics as well as a historical background of the development of our present day understanding of fatigue has been done. (orig.) [de

  9. Evaluation of Standard Concepts Design of Library Interior Physical Environment

    Directory of Open Access Journals (Sweden)

    Debri Harindya Putri

    2018-01-01

    Full Text Available Currently the function of a room is not only used as a shelter, the function of the room itself to be increased as a refreshing or relaxation area for users to follow the development of creativity and technology in the field of design. The comfortable factor becomes the main factor that indicates a successful process of creating a space. No exception library. The nature of library seemed stiff because of its function as a place to read, now can be developed and made into more dynamic with the special design concepts or color patterns used. Libraries can be created a special concept that suits the characteristics of the users themselves. Most users of the library, especially in college libraries are teenagers. Naturally, teenagers like to gather with their friends and we have to facilitate this activity in our library design concept. In addition we can also determine the needs of users through research by questionnaire method. The answers of users can be mapped and drawn conclusions. To explore the research, the author reviewed some literature about library interior design and observed the library of Ma Chung University as a case study. The combined results of the method can be concluded and the discovery of ideal standards of physical environment. So, the library can be made as a comfortable reading environment so as to increased interest in reading behavior and the frequent visits of students in the library

  10. Probabilistic Evaluation of Eurocode 5 Fire Design Criteria of a ...

    African Journals Online (AJOL)

    Structural reliability analysis for a three-hinge timber portal frame subjected to fire was undertaken. Eight modes of failure were identified for the frame and limit state function was formulated for each failure mode. The limit state functions were based on the Eurocode 5 design criteria. Uncertainties in the timber material ...

  11. Internet information triangulation: Design theory and prototype evaluation

    NARCIS (Netherlands)

    Wijnhoven, Alphonsus B.J.M.; Brinkhuis, Michel

    2014-01-01

    Many discussions exist regarding the credibility of information on the Internet. Similar discussions happen on the interpretation of social scientific research data, for which information triangulation has been proposed as a useful method. In this article, we explore a design theory—consisting of a

  12. Design and evaluation of a heat recuperator for steel slags

    International Nuclear Information System (INIS)

    Gutiérrez Trashorras, Antonio J.; Álvarez, Eduardo Álvarez; Río González, José Luis; Suarez Cuesta, José Manuel; Bernat, Jorge Xiberta

    2013-01-01

    New techniques for emissions reduction and energy efficiency are important challenges of the steel industry. Although great advantages have been reached in these fields, there are still new opportunities. One of them is the possible development of systems to recover energy from slags. The recent policies that encourage the use of renewable and alternative energies determine a favorable scenario for the development of new techniques of heat recovering. In this context, this article presents a new heat recuperation system for the slags produced in the factories of Arcelor–Mittal in Asturias (Spain) and study in detail the design of an innovative slags heat exchanger. To adjust its performance and to determine the influence of the geometric and flow design parameters, the heat exchanger has been simulated using numerical analysis software (CFD). -- Highlights: • A new design of a heat recuperator for slags energy recovery is presented. • The effects of the design parameters have been studied with a numerical model. • Refractory materials with high thermal conductivity improve heat recuperation

  13. Evaluation of j-turn intersection design performance in Missouri.

    Science.gov (United States)

    2013-12-01

    Research shows that a high percentage of crashes that take place on high-speed rural expressways occur at intersections with : minor roads. One low-cost alternative design for improving the safety of at-grade intersections on such expressways is the ...

  14. Design and performance evaluation of very thin overlays in Texas.

    Science.gov (United States)

    2009-06-01

    Very thin overlays 1-inch thick or less were placed as surface layers on five major highways in Texas. : These mixes were designed in the laboratory to have a balance of good rut resistance as measured by : TxDOTs Hamburg Wheel Tracking test and g...

  15. Structural higher education reform - design and evaluation: synthesis report

    NARCIS (Netherlands)

    File, Jonathan M.; Huisman, Jeroen; de Boer, Harry F.; Seeber, Marco; Vukasovic, Martina; Westerheijden, Donald F.

    2016-01-01

    This study analyses how different types of system-level (or ‘landscape’) structural reforms in higher education have been designed and implemented in selected higher education systems. In the 12 case studies that form the core of the project, the researchers examine reforms aimed at: - Increasing

  16. Large scale solar district heating. Evaluation, modelling and designing - Appendices

    Energy Technology Data Exchange (ETDEWEB)

    Heller, A.

    2000-07-01

    The appendices present the following: A) Cad-drawing of the Marstal CSHP design. B) Key values - large-scale solar heating in Denmark. C) Monitoring - a system description. D) WMO-classification of pyranometers (solarimeters). E) The computer simulation model in TRNSYS. F) Selected papers from the author. (EHS)

  17. Risk allocation approach to reactor safety design and evaluation

    International Nuclear Information System (INIS)

    Gokcek, O.; Temme, M.I.; Derby, S.L.

    1978-01-01

    This paper describes a risk allocation technique used for determining nuclear power plant design reliability requirements. The concept of risk allocation-optimum choice of safety function reliabilities under a maximum risk constraint - is described. An example of risk allocation is presented to demonstrate the application of the methodology

  18. Use of workplace evaluations in briefing and design

    NARCIS (Netherlands)

    van der Voordt, Theo; Haugen, Tore I.; Moum, Anita; Brochner, Jan

    2006-01-01

    Many organizations are engaged in organizational change, adopting new management styles and new ways of working. Innovative workplace design is used to facilitate organizational change, to improve user satisfaction and labour productivity, and to lower facility costs. Although some research has been

  19. Automatic evaluation of task-focused parallel jaw gripper design

    DEFF Research Database (Denmark)

    Wolniakowski, Adam; Miatliuk, Konstantsin; Krüger, Norbert

    2014-01-01

    In this paper, we suggest gripper quality metrics that indicate the performance of a gripper given an object CAD model and a task description. Those, we argue, can be used in the design and selection of an appropriate gripper when the task is known. We present three different gripper metrics that...

  20. Design and evaluation of steel bridges with double composite action

    Science.gov (United States)

    2010-02-01

    This report presents findings from a cooperative USF/URS/FDOT research study undertaken to develop design rules for : double composite steel bridges. In the study, a 48 ft long, 16 ft wide, 4 ft. 10 in. deep trapezoidal HPS 70W box section : desig...

  1. Design, synthesis and bioactivity evaluation of tribactam beta lactamase inhibitors.

    Science.gov (United States)

    Copar, Anton; Prevec, Tadeja; Anzic, Borut; Mesar, Tomaz; Selic, Lovro; Vilar, Mateja; Solmajer, Tom

    2002-03-25

    Known carbapenem compounds with inhibitory effect towards beta-lactamase enzymes are formed from bicyclical beta lactam structural scaffolds. On the basis of results from theoretical computational methods and molecular modelling we have designed and developed a synthetic route towards novel, biologically active tricyclic derivatives of carbapenems.

  2. Design, construction and evaluation of a meteorological mobile mast ...

    African Journals Online (AJOL)

    A 30 metre meteorological mobile mast has been designed and constructed for upper air profile measurements. The parameters to be measured are wind speed, wind direction, temperature and relative humidity. The sensors for each parameter to be measured are constructed with locally available materials.

  3. Design, Fabrication and Evaluation of a Plantain Roaster | Ezekiel ...

    African Journals Online (AJOL)

    In this work, an electric roaster capable of roasting twenty-one plantain fingers per batch was designed, fabricated and tested. The roaster had two electric heating elements (one at the top and the other at the base of the roaster) supplying power at the rate of 2.4 kW. In addition ... However, sample at the upper layer

  4. Question Sets and Profiles: A Technique for Evaluating Building Design.

    Science.gov (United States)

    Scoffham, Stephen

    1982-01-01

    A questionnaire (survey sheet) has been developed focusing on some of the factors an architect has to consider in designing a house (site, appearance, suitability, and building maintenance). The use of the questionnaire by students and "spin off" activities are discussed. (Author/JN)

  5. Design and Evaluation of Accelerometer based Motional Feedback

    DEFF Research Database (Denmark)

    Schneider, Henrik; Pranjic, Emilio; Agerkvist, Finn T.

    2015-01-01

    and enable radical design changes in the loudspeaker which can lead to efficiency improvements. In combination this has motivated a revisit of the accelerometer based motional feedback technique. Experimental results on a 8 inch subwoofer show that the total harmonic distortion can be significantly reduced...

  6. Design and evaluation of fluidized bed heat recovery for diesel engine systems

    Science.gov (United States)

    Hamm, J. R.; Newby, R. A.; Vidt, E. J.; Lippert, T. E.

    1985-01-01

    The potential of utilizing fluidized bed heat exchangers in place of conventional counter-flow heat exchangers for heat recovery from adiabatic diesel engine exhaust gas streams was studied. Fluidized bed heat recovery systems were evaluated in three different heavy duty transport applications: (1) heavy duty diesel truck; (2) diesel locomotives; and (3) diesel marine pushboat. The three applications are characterized by differences in overall power output and annual utilization. For each application, the exhaust gas source is a turbocharged-adiabatic diesel core. Representative subposed exhaust gas heat utilization power cycles were selected for conceptual design efforts including design layouts and performance estimates for the fluidized bed heat recovery heat exchangers. The selected power cycles were: organic rankine with RC-1 working fluid, turbocompound power turbine with steam injection, and stirling engine. Fuel economy improvement predictions are used in conjunction with capital cost estimates and fuel price data to determine payback times for the various cases.

  7. Super Energy Efficiency Design (S.E.E.D.) Home Evaluation

    Energy Technology Data Exchange (ETDEWEB)

    German, A.; Dakin, B.; Backman, C.; Weitzel, E.; Springer, D.

    2012-12-01

    This report describes the results of evaluation by the Alliance for Residential Building Innovation (ARBI) Building America team of the 'Super Energy Efficient Design' (S.E.E.D) home, a 1,935 sq. ft., single-story spec home located in Tucson, AZ. This prototype design was developed with the goal of providing an exceptionally energy efficient yet affordable home and includes numerous aggressive energy features intended to significantly reduce heating and cooling loads such as structural insulated panel (SIP) walls and roof, high performance windows, an ERV, an air-to-water heat pump with mixed-mode radiant and forced air delivery, solar water heating, and rooftop PV. Source energy savings are estimated at 45% over the Building America B10 Benchmark. System commissioning, short term testing, long term monitoring and detailed analysis of results was conducted to identify the performance attributes and cost effectiveness of the whole house measure package.

  8. Independent Evaluation of the integrated Community Case Management of Childhood Illness Strategy in Malawi Using a National Evaluation Platform Design.

    Science.gov (United States)

    Amouzou, Agbessi; Kanyuka, Mercy; Hazel, Elizabeth; Heidkamp, Rebecca; Marsh, Andrew; Mleme, Tiope; Munthali, Spy; Park, Lois; Banda, Benjamin; Moulton, Lawrence H; Black, Robert E; Hill, Kenneth; Perin, Jamie; Victora, Cesar G; Bryce, Jennifer

    2016-03-01

    We evaluated the impact of integrated community case management of childhood illness (iCCM) on careseeking for childhood illness and child mortality in Malawi, using a National Evaluation Platform dose-response design with 27 districts as units of analysis. "Dose" variables included density of iCCM providers, drug availability, and supervision, measured through a cross-sectional cellular telephone survey of all iCCM-trained providers. "Response" variables were changes between 2010 and 2014 in careseeking and mortality in children aged 2-59 months, measured through household surveys. iCCM implementation strength was not associated with changes in careseeking or mortality. There were fewer than one iCCM-ready provider per 1,000 under-five children per district. About 70% of sick children were taken outside the home for care in both 2010 and 2014. Careseeking from iCCM providers increased over time from about 2% to 10%; careseeking from other providers fell by a similar amount. Likely contributors to the failure to find impact include low density of iCCM providers, geographic targeting of iCCM to "hard-to-reach" areas although women did not identify distance from a provider as a barrier to health care, and displacement of facility careseeking by iCCM careseeking. This suggests that targeting iCCM solely based on geographic barriers may need to be reconsidered. © The American Society of Tropical Medicine and Hygiene.

  9. Evaluation design of New York City's regulations on nutrition, physical activity, and screen time in early child care centers.

    Science.gov (United States)

    Breck, Andrew; Goodman, Ken; Dunn, Lillian; Stephens, Robert L; Dawkins, Nicola; Dixon, Beth; Jernigan, Jan; Kakietek, Jakub; Lesesne, Catherine; Lessard, Laura; Nonas, Cathy; O'Dell, Sarah Abood; Osuji, Thearis A; Bronson, Bernice; Xu, Ye; Kettel Khan, Laura

    2014-10-16

    This article describes the multi-method cross-sectional design used to evaluate New York City Department of Health and Mental Hygiene's regulations of nutrition, physical activity, and screen time for children aged 3 years or older in licensed group child care centers. The Center Evaluation Component collected data from a stratified random sample of 176 licensed group child care centers in New York City. Compliance with the regulations was measured through a review of center records, a facility inventory, and interviews of center directors, lead teachers, and food service staff. The Classroom Evaluation Component included an observational and biometric study of a sample of approximately 1,400 children aged 3 or 4 years attending 110 child care centers and was designed to complement the center component at the classroom and child level. The study methodology detailed in this paper may aid researchers in designing policy evaluation studies that can inform other jurisdictions considering similar policies.

  10. An evaluation of telehealth websites for design, literacy, information and content.

    Science.gov (United States)

    Whitten, Pamela; Holtz, Bree; Cornacchione, Jennifer; Wirth, Christina

    2011-01-01

    We examined 62 telehealth websites using four assessment criteria: design, literacy, information and telehealth content. The websites came from the member list of the American Telemedicine Association and the Office for the Advancement of Telehealth and partner sites, and were included if they were currently active and at least three clicks deep. Approximately 130 variables were examined for each website by two independent researchers. The websites reviewed contained most of the design variables (mean 74%, SD 6), but fewer of those relating to literacy (mean 26%, SD 6), website information (mean 35%, SD 16) and telehealth content (mean 37%, SD 18). Only 29% of websites encouraged users to ask about telehealth, and 19% contained information on overcoming telehealth barriers. Nonetheless, 84% promoted awareness of telehealth. All evaluation assessments were significantly correlated with each other except for literacy and information. The present study identified various matters that should be addressed when developing telehealth websites. Although much of this represents simple common sense in website design, our evaluation demonstrates that there is still much room for improvement.

  11. Design and evaluation of a new ergonomic handle for instruments in minimally invasive surgery.

    Science.gov (United States)

    Sancibrian, Ramon; Gutierrez-Diez, María C; Torre-Ferrero, Carlos; Benito-Gonzalez, Maria A; Redondo-Figuero, Carlos; Manuel-Palazuelos, Jose C

    2014-05-01

    Laparoscopic surgery techniques have been demonstrated to provide massive benefits to patients. However, surgeons are subjected to hardworking conditions because of the poor ergonomic design of the instruments. In this article, a new ergonomic handle design is presented. This handle is designed using ergonomic principles, trying to provide both more intuitive manipulation of the instrument and a shape that reduces the high-pressure zones in the contact with the surgeon's hand. The ergonomic characteristics of the new handle were evaluated using objective and subjective studies. The experimental evaluation was performed using 28 volunteers by means of the comparison of the new handle with the ring-handle (RH) concept in an instrument available on the market. The volunteers' muscle activation and motions of the hand, wrist, and arm were studied while they performed different tasks. The data measured in the experiment include electromyography and goniometry values. The results obtained from the subjective analysis reveal that most volunteers (64%) preferred the new prototype to the RH, reporting less pain and less difficulty to complete the tasks. The results from the objective study reveal that the hyperflexion of the wrist required for the manipulation of the instrument is strongly reduced. The new ergonomic handle not only provides important ergonomic advantages but also improves the efficiency when completing the tasks. Compared with RH instruments, the new prototype reduced the high-pressure areas and the extreme motions of the wrist. Copyright © 2014 Elsevier Inc. All rights reserved.

  12. Design study on dose evaluation method for employees at severe accident

    International Nuclear Information System (INIS)

    Yoshida, Yoshitaka; Irie, Takashi; Kohriyama, Tamio; Kudo, Seiichi; Nishimura, Kazuya

    2001-01-01

    When we assume a severe accident in a nuclear power plant, it is required for rescue activity in the plant, accident management, repair work of failed parts and evaluation of employees to obtain radiation dose rate distribution or map in the plant and estimated dose value for the above works. However it might be difficult to obtain them accurately along the progress of the accident, because radiation monitors are not always installed in the areas where the accident management is planned or the repair work is thought for safety-related equipments. In this work, we analyzed diffusion of radioactive materials in case of a severe accident in a pressurized water reactor plant, investigated a method to obtain radiation dose rate in the plant from estimated radioactive sources, made up a prototype analyzing system by modeling a specific part of components and buildings in the plant from this design study on dose evaluation method for employees at severe accident, and then evaluated its availability. As a result, we obtained the followings: (1) A new dose evaluation method was established to predict the radiation dose rate in any point in the plant during a severe accident scenario. (2) This evaluation of total dose including moving route and time for the accident management and the repair work is useful for estimating radiation dose limit for these actions of the employees. (3) The radiation dose rate map is effective for identifying high radiation areas and for choosing a route with lower radiation dose rate. (author)

  13. Design study on dose evaluation method for employees at severe accident

    Energy Technology Data Exchange (ETDEWEB)

    Yoshida, Yoshitaka; Irie, Takashi; Kohriyama, Tamio [Institute of Nuclear Safety Systems Inc., Mihama, Fukui (Japan); Kudo, Seiichi [Mitsubishi Heavy Industries Ltd., Tokyo (Japan); Nishimura, Kazuya [Computer Software Development Co., Ltd., Tokyo (Japan)

    2001-09-01

    When we assume a severe accident in a nuclear power plant, it is required for rescue activity in the plant, accident management, repair work of failed parts and evaluation of employees to obtain radiation dose rate distribution or map in the plant and estimated dose value for the above works. However it might be difficult to obtain them accurately along the progress of the accident, because radiation monitors are not always installed in the areas where the accident management is planned or the repair work is thought for safety-related equipments. In this work, we analyzed diffusion of radioactive materials in case of a severe accident in a pressurized water reactor plant, investigated a method to obtain radiation dose rate in the plant from estimated radioactive sources, made up a prototype analyzing system by modeling a specific part of components and buildings in the plant from this design study on dose evaluation method for employees at severe accident, and then evaluated its availability. As a result, we obtained the followings: (1) A new dose evaluation method was established to predict the radiation dose rate in any point in the plant during a severe accident scenario. (2) This evaluation of total dose including moving route and time for the accident management and the repair work is useful for estimating radiation dose limit for these actions of the employees. (3) The radiation dose rate map is effective for identifying high radiation areas and for choosing a route with lower radiation dose rate. (author)

  14. Interactive Block Games for Assessing Children's Cognitive Skills: Design and Preliminary Evaluation

    Directory of Open Access Journals (Sweden)

    Kiju Lee

    2018-05-01

    Full Text Available Background: This paper presents design and results from preliminary evaluation of Tangible Geometric Games (TAG-Games for cognitive assessment in young children. The TAG-Games technology employs a set of sensor-integrated cube blocks, called SIG-Blocks, and graphical user interfaces for test administration and real-time performance monitoring. TAG-Games were administered to children from 4 to 8 years of age for evaluating preliminary efficacy of this new technology-based approach.Methods: Five different sets of SIG-Blocks comprised of geometric shapes, segmented human faces, segmented animal faces, emoticons, and colors, were used for three types of TAG-Games, including Assembly, Shape Matching, and Sequence Memory. Computational task difficulty measures were defined for each game and used to generate items with varying difficulty. For preliminary evaluation, TAG-Games were tested on 40 children. To explore the clinical utility of the information assessed by TAG-Games, three subtests of the age-appropriate Wechsler tests (i.e., Block Design, Matrix Reasoning, and Picture Concept were also administered.Results: Internal consistency of TAG-Games was evaluated by the split-half reliability test. Weak to moderate correlations between Assembly and Block Design, Shape Matching and Matrix Reasoning, and Sequence Memory and Picture Concept were found. The computational measure of task complexity for each TAG-Game showed a significant correlation with participants' performance. In addition, age-correlations on TAG-Game scores were found, implying its potential use for assessing children's cognitive skills autonomously.

  15. osDesign: An R Package for the Analysis, Evaluation, and Design of Two-Phase and Case-Control Studies

    Directory of Open Access Journals (Sweden)

    Sebastien Haneuse

    2011-08-01

    Full Text Available The two-phase design has recently received attention in the statistical literature as an extension to the traditional case-control study for settings where a predictor of interest is rare or subject to missclassification. Despite a thorough methodological treatment and the potential for substantial efficiency gains, the two-phase design has not been widely adopted. This may be due, in part, to a lack of general-purpose, readily-available software. The osDesign package for R provides a suite of functions for analyzing data from a two-phase and/or case-control design, as well as evaluating operating characteristics, including bias, efficiency and power. The evaluation is simulation-based, permitting flexible application of the package to a broad range of scientific settings. Using lung cancer mortality data from Ohio, the package is illustrated with a detailed case-study in which two statistical goals are considered: (i the evaluation of small-sample operating characteristics for two-phase and case-control designs and (ii the planning and design of a future two-phase study.

  16. Evaluation and Design of Supply Chain Operations using DEA

    NARCIS (Netherlands)

    C.M. Chen (Chien-Ming)

    2009-01-01

    textabstractPerformance evaluation has been one of the most critical components in management. As production systems nowadays consist of a growing number of integrated and interacting processes, the interrelationship and dynamic among processes have create a major challenge in measuring system and

  17. Design and evaluation of a virtual gearshift application

    NARCIS (Netherlands)

    Tideman, Martijn; van der Voort, Mascha C.; van Houten, Frederikus J.A.M.

    2004-01-01

    When a customer buys a new car, he or she wants it to address personal preferences with respect to its driving behavior. By utilizing virtual reality technology, a virtual prototyping environment (VPE) can be created in which the behavior of a vehicle or part of a vehicle can be evaluated and

  18. Design and evaluation of a multithreaded many-core architecture

    NARCIS (Netherlands)

    Lankamp, M.

    2015-01-01

    Performance improvements for microprocessors have traditionally been achieved by increasing their clock frequency. However, this technique has reached a point where further scaling is impractical. This thesis describes and evaluates a novel System-on-Chip architecture that focuses on exploiting all

  19. A Preliminary Rubric Design to Evaluate Mixed Methods Research

    Science.gov (United States)

    Burrows, Timothy J.

    2013-01-01

    With the increase in frequency of the use of mixed methods, both in research publications and in externally funded grants there are increasing calls for a set of standards to assess the quality of mixed methods research. The purpose of this mixed methods study was to conduct a multi-phase analysis to create a preliminary rubric to evaluate mixed…

  20. Design and Evaluation of an Online Freshmen Course

    Directory of Open Access Journals (Sweden)

    Lewis McAnally Salas

    2000-05-01

    Full Text Available This paper describes the development of a prototype for an undergraduate online course tested with freshmen students taking mathematics for a B.Sc. in Oceanography.  The design of the prototype focuses on the six basic components for the selection and use of technologies in online teaching and learning; namely, a delivery and access, b control, c interaction, d symbolic characteristics of the medium e social presence and f human-machine interface. The results report the degree of satisfaction with the prototype and the course.  These results, obtained through questionnaires and semi-structured interviews, address issues concerning the structure and design of the online course.  The participants’ answers highlighted the easiness of navigation within the course and the effective communication obtained with the use of the course's electronic tools.