BOD-DO modeling and water quality analysis of a waste water outfall off Kochi, west coast of India

Digital Repository Service at National Institute of Oceanography (India)

Babu, M.T.; Das, V.K.; Vethamony, P.

Water quality scenarios around an offshore outfall off Kochi were simulated using MIKE21 water quality model, assuming a high Biochemical Oxygen Demand (BOD=50 mgl sup(-1)) effluent discharge. The discharge is introduced into the model through...

Removal of chemical oxygen demand from textile wastewater using a natural coagulant

Energy Technology Data Exchange (ETDEWEB)

Ramavandi, Bahman [Bushehr University of Medical Sciences, Bushehr (Iran, Islamic Republic of); Farjadfard, Sima [Islamic Azad University, Tehran (Iran, Islamic Republic of)

2014-01-15

A biomaterial was successfully synthesized from Plantago ovata by using an FeCl{sub 3}-induced crude extract (FCE). The potential of FCE to act as a natural coagulant was tested for the pretreatment of real textile wastewater. Tests were performed to evaluate the effects of FCE quantity, salt concentration, and wastewater pH on chemical oxygen demand (COD) reduction during a coagulation/flocculation process. Experimental results indicated that the wastewater could be effectively treated by using a coagulation/flocculation process, where the BOD{sub 5}/COD ratio of the effluent was improved to 0.48. A low coagulant dose, 1.5mg/L, achieved a high COD removal percentage, 89%, at operational conditions of neutral pH and room temperature. The experimental data revealed that the maximum COD removal occurred at water pH<8. Increasing the salt promoted the COD removal. The settling and filterability characteristics of the sludge were also studied. Scanning electron microscopy and energy dispersive spectroscopy studies were conducted to determine the sludge structure and composition, respectively. Overall, FCE as an eco-friendly biomaterial was revealed to be a very efficient coagulant and a promising option for the removal of COD from wastewaters.

Correlation of COD and BOD of domestic wastewater with the power output of bioreactor

Energy Technology Data Exchange (ETDEWEB)

Khan, A M; Ataullah,; Shaheen, A; Ahmad, I; Malik, F; Shahid, H A [Federal Urdu University of Arts, Science and Technology, Gulshan-e-Iqbal Campus, University Road, Karachi-75300 (Pakistan). Research Laboratory of Bioenergy, Department of Chemistry

2011-04-15

This research article deals with the studies on the development of the correlation of COD, BOD, and BOD/sub 5/ of domestic wastewater (DWW), and fermented domestic wastewater (FDWW) with the power output of the microbial fuel cell (MFC). The fermentation of DWW was carried out with yeast (Saccharomyces cerevisiae), and yogurt bacteria (Streptococcus lactis) to produce biohydrogen which was converted to the electrical energy through the development of microbial fuel cell (MFC). The values of COD, BOD, and BOD/sub 5/ for yogurt fermented domestic wastewater (Yogurt-FDWW) were found to be greater than the values of yeast fermented domestic wastewater (Yeast-FDWW). The power output of DWW and FDWW was increased with the increase in COD, BOD and BOD/sub 5/ values. The main objective of this article is to develop the renewable alternative of fossil fuels which are the major cause of global warming and global pollution. (author)

Correlation of COD and BOD of domestic wastewater with the power output of bioreactor

International Nuclear Information System (INIS)

Khan, A.M.; Ataullah; Shaheen, A.; Ahmad, I.; Malik, F.; Shahid, H.A.

2011-01-01

This research article deals with the studies on the development of the correlation of COD, BOD, and BOD/sub 5/ of domestic wastewater (DWW), and fermented domestic wastewater (FDWW) with the power output of the microbial fuel cell (MFC). The fermentation of DWW was carried out with yeast (Saccharomyces cerevisiae), and yogurt bacteria (Streptococcus lactis) to produce biohydrogen which was converted to the electrical energy through the development of microbial fuel cell (MFC). The values of COD, BOD, and BOD/sub 5/ for yogurt fermented domestic wastewater (Yogurt-FDWW) were found to be greater than the values of yeast fermented domestic wastewater (Yeast-FDWW). The power output of DWW and FDWW was increased with the increase in COD, BOD and BOD/sub 5/ values. The main objective of this article is to develop the renewable alternative of fossil fuels which are the major cause of global warming and global pollution. (author)

Construction of Microbial-based Biosensor to Measure BOD of Industrial Wastewaters

Directory of Open Access Journals (Sweden)

Behnam Mahdavi

2014-04-01

Full Text Available In this study a cell-based biosensor for measurement of BOD was designed and developed. Activated sludge collected from wastewater treatment plant of Shahinshahr was used as biological receptor and a Clark cell was used as transducer. According to the results obtained from the sensor calibration, a linear relationship between the current changes and glucose-glutamic acid (GAA standard concentrations up to 50 mg/L was observed. The BOD values of different industrial wastewaters, inlet and outlet of treatment plant of Ardineh Company (Isfahan, and also  inlet and outlet of domestic wastewater treatment plant of Shahinshahr, and outlet of treatment plant of Pegah Company (Isfahan were measured using this biosensor. Comparison of the results of this biosensor and the results of the standard BOD test (BOD5 showed that the mean percentage error measured by the sensor was +29.6%. The results concerning the stability of the designed biosensor showed a stability time of 3 days for the response of biosensor.

Chemical oxygen demand (cod) attenuation of methyl red in water ...

African Journals Online (AJOL)

Chemical oxygen demand (cod) attenuation of methyl red in water using biocarbons obtained from Nipa palm leaves. ... eco-friendly and locally accessible biocarbon for mitigation of organic contaminants in water. Keywords: Chemical oxygen demand, biocarbon, methyl red, biodegradation, bioremediation, Nipa palm ...

Correlating Biochemical and Chemical Oxygen Demand of Effluents

African Journals Online (AJOL)

F. K. Attiogbe1, Mary Glover-Amengor2 and K. T. Nyadziehe3

There is also a slaughterhouse for animals (Sarfo-Afriyie, 1999). ... day period of the BOD test, the bacteria oxidized mainly the soluble organic ..... characteristics of the waste (effluent) not being constant (http://www.hach.com), and this is.

Facultative Stabilization Pond: Measuring Biological Oxygen Demand using Mathematical Approaches

Science.gov (United States)

Wira S, Ihsan; Sunarsih, Sunarsih

2018-02-01

Pollution is a man-made phenomenon. Some pollutants which discharged directly to the environment could create serious pollution problems. Untreated wastewater will cause contamination and even pollution on the water body. Biological Oxygen Demand (BOD) is the amount of oxygen required for the oxidation by bacteria. The higher the BOD concentration, the greater the organic matter would be. The purpose of this study was to predict the value of BOD contained in wastewater. Mathematical modeling methods were chosen in this study to depict and predict the BOD values contained in facultative wastewater stabilization ponds. Measurements of sampling data were carried out to validate the model. The results of this study indicated that a mathematical approach can be applied to predict the BOD contained in the facultative wastewater stabilization ponds. The model was validated using Absolute Means Error with 10% tolerance limit, and AME for model was 7.38% (< 10%), so the model is valid. Furthermore, a mathematical approach can also be applied to illustrate and predict the contents of wastewater.

BAYESIAN PARAMETER ESTIMATION IN A MIXED-ORDER MODEL OF BOD DECAY. (U915590)

Science.gov (United States)

We describe a generalized version of the BOD decay model in which the reaction is allowed to assume an order other than one. This is accomplished by making the exponent on BOD concentration a free parameter to be determined by the data. This "mixed-order" model may be ...

Effects of Operating Parameters on Measurements of Biochemical Oxygen Demand Using a Mediatorless Microbial Fuel Cell Biosensor

Directory of Open Access Journals (Sweden)

Min-Chi Hsieh

2015-12-01

Full Text Available The conventional Biochemical Oxygen Demand (BOD method takes five days to analyze samples. A microbial fuel cell (MFC may be an alternate tool for rapid BOD determination in water. However, a MFC biosensor for continuous BOD measurements of water samples is still unavailable. In this study, a MFC biosensor inoculated with known mixed cultures was used to determine the BOD concentration. Effects of important parameters on establishing a calibration curve between the BOD concentration and output signal from the MFC were evaluated. The results indicate monosaccharides were good fuel, and methionine, phenylalanine, and ethanol were poor fuels for electricity generation by the MFC. Ions in the influent did not significantly affect the MFC performance. CN− in the influent could alleviate the effect of antagonistic electron acceptors on the MFC performance. The regression equation for BOD concentration and current density of the biosensor was y = 0.0145x + 0.3317. It was adopted to measure accurately and continuously the BOD concentration in actual water samples at an acceptable error margin. These results clearly show the developed MFC biosensor has great potential as an alternative BOD sensing device for online measurements of wastewater BOD.

An optical biosensing film for biochemical oxygen demand determination in seawater with an automatic flow sampling system

Science.gov (United States)

Xin, Lingling; Wang, Xudong; Guo, Guangmei; Wang, Xiaoru; Chen, Xi

2007-09-01

An on-line roboticized apparatus, including an optical biosensing film with an automatic flow sampling system, has been developed for biochemical oxygen demand (BOD) determination of seawater. The sensing film employed in the apparatus consisted of an organically modified silicate (ORMOSIL) film embedded with tri(4,7-diphenyl-1,10-phenanthroline) ruthenium(II) perchlorate. Three species of microorganism cultivated from seawater were immobilized in an ORMOSIL-polyvinyl alcohol matrix. Possible factors affecting BOD determination were studied, including sampling frequency, temperature, pH and sodium chloride concentration. Based on measurements of the linear fluctuant coefficients and the reproducibility of its response to seawater, the BOD apparatus showed the advantages of high veracity and short response time. Generally, the linear fluctuant coefficient (R2) in the BOD range 0.2-40 mg l-1 was 0.9945 when using a glucose/glutamate (GGA) BOD standard solution. A reproducible response for the BOD sensing film of within ±2.8% could be obtained in the 2 mg l-1 GGA solution. The BOD apparatus was applied to the BOD determination of seawater, and the values estimated by this biosensing apparatus correlated well with those determined by the conventional 5 day BOD (BOD5) test.

Biological Oxygen Demand in Soils and Litters

Science.gov (United States)

Smagin, A. V.; Smagina, M. V.; Sadovnikova, N. B.

2018-03-01

Biological oxygen demand (BOD) in mineral and organic horizons of soddy-podzolic soils in the forest-park belt of Moscow as an indicator of their microbial respiration and potential biodestruction function has been studied. The BOD of soil samples has been estimated with a portable electrochemical analyzer after incubation in closed flasks under optimum hydrothermal conditions. A universal gradation scale of this parameter from very low (140 g O2/(m3 h)) has been proposed for mineral and organic horizons of soil. A physically substantiated model has been developed for the vertical distribution of BOD in the soil, which combines the diffusion transport of oxygen from the atmosphere and its biogenic uptake in the soil by the first-order reaction. An analytical solution of the model in the stationary state has been obtained; from it, the soil oxygen diffusivity and the kinetic constants of O2 uptake have been estimated, and the profile-integrated total BOD value has been calculated (0.4-1.8 g O2/(m2 h)), which is theoretically identical to the potential oxygen flux from the soil surface due to soil respiration. All model parameters reflect the recreation load on the soil cover by the decrease in their values against the control.

THE DEVELOPMENT OF BIOCHEMICAL OXYGEN DEMAND SENSOR USING LOCAL YEAST: Candida fukuyamaensis, UICC Y-247

Directory of Open Access Journals (Sweden)

Endang Saepudin

2011-04-01

Full Text Available In order to shorten the measurement time of biochemical oxygen demand (BOD, a BOD sensor based on yeastmetabolism was developed. Local yeast, Indonesian Origin, Candida fukuyamaensis UICC Y-247, was used as atransducer. The yeast was immobilized as a thin film in agarose matrix with the auxiliary of Nafion® acting as themembrane for ion exchange process. The film was then attached to gold-modified glassy carbons and used as transduceron the working electrodes. The measurements were conducted by observing the depletion of glucose concentrationusing multipulse amperometric method and then converted to BOD values. Optimum condition was observed in awaiting measurement time of 30 min at an applied potential of 450 mV (vs. Ag/AgCl. Linearity was shown in glucoseconcentration range of 0.1–0.5 mM, which was equivalent to BOD concentration range of 10–50 mg/L. A detectionlimit of 1.13 mg/L BOD could be achieved. Good repeatability was shown by a relative standard deviation (RSD of2.7% (n = 15. However, decreasing current response of ~50% was found after 3 days. Comparing to the conventionalBOD measurement, this BOD sensor can be used as an alternative method for BOD measurements.

Enhancing Signal Output and Avoiding BOD/Toxicity Combined Shock Interference by Operating a Microbial Fuel Cell Sensor with an Optimized Background Concentration of Organic Matter

Directory of Open Access Journals (Sweden)

Yong Jiang

2016-08-01

Full Text Available In the monitoring of pollutants in an aquatic environment, it is important to preserve water quality safety. Among the available analysis methods, the microbial fuel cell (MFC sensor has recently been used as a sustainable and on-line electrochemical microbial biosensor for biochemical oxygen demand (BOD and toxicity, respectively. However, the effect of the background organic matter concentration on toxicity monitoring when using an MFC sensor is not clear and there is no effective strategy available to avoid the signal interference by the combined shock of BOD and toxicity. Thus, the signal interference by the combined shock of BOD and toxicity was systematically studied in this experiment. The background organic matter concentration was optimized in this study and it should be fixed at a high level of oversaturation for maximizing the signal output when the current change (ΔI is selected to correlate with the concentration of a toxic agent. When the inhibition ratio (IR is selected, on the other hand, it should be fixed as low as possible near the detection limit for maximizing the signal output. At least two MFC sensors operated with high and low organic matter concentrations and a response chart generated from pre-experiment data were both required to make qualitative distinctions of the four types of combined shock caused by a sudden change in BOD and toxicity.

Factors affecting the performance of a single-chamber microbial fuel cell-type biological oxygen demand sensor.

Science.gov (United States)

Yang, Gai-Xiu; Sun, Yong-Ming; Kong, Xiao-Ying; Zhen, Feng; Li, Ying; Li, Lian-Hua; Lei, Ting-Zhou; Yuan, Zhen-Hong; Chen, Guan-Yi

2013-01-01

Microbial fuel cells (MFCs) are devices that exploit microorganisms as biocatalysts to degrade organic matter or sludge present in wastewater (WW), and thereby generate electricity. We developed a simple, low-cost single-chamber microbial fuel cell (SCMFC)-type biochemical oxygen demand (BOD) sensor using carbon felt (anode) and activated sludge, and demonstrated its feasibility in the construction of a real-time BOD measurement system. Further, the effects of anodic pH and organic concentration on SCMFC performance were examined, and the correlation between BOD concentration and its response time was analyzed. Our results demonstrated that the SCMFC exhibited a stable voltage after 132 min following the addition of synthetic WW (BOD concentration: 200 mg/L). Notably, the response signal increased with an increase in BOD concentration (range: 5-200 mg/L) and was found to be directly proportional to the substrate concentration. However, at higher BOD concentrations (>120 mg/L) the response signal remained unaltered. Furthermore, we optimized the SCMFC using synthetic WW, and tested it with real WW. Upon feeding real WW, the BOD values exhibited a standard deviation from 2.08 to 8.3% when compared to the standard BOD5 method, thus demonstrating the practical applicability of the developed system to real treatment effluents.

Lysimeter experiments to determine the ability of soil to reduce concentrations of BOD, available P and inorganic N in dirty water.

Science.gov (United States)

Brookman, S K E; Chadwick; Retter, A R

2005-11-01

Lysimeter experiments were conducted to determine the ability of different soils to reduce levels of biochemical oxygen demand (BOD) and concentrations of molybdate reactive phosphorus (MRP) and ammonium-N (NH4(+)-N) in dirty water and the impact of applications on nitrate leaching. An additional experiment investigated the effect of dirty water components on leaching quality. This information is required to assess the potential risk of dirty water applications on polluting groundwater and to assess the use of such soils in the development of treatment systems for dirty water. Intact and disturbed soil lysimeters, 0.5 and 1m deep were constructed from four soils; a coarse free-draining sandy loam, a sandy loam over soft sandstone, a calcareous silty clay over chalk and a sandy loam over granite. For the coarse free-draining sandy loam, lysimeters were also constructed from disturbed soil with and without the addition of lime, to assess if this could increase phosphorus immobilisation. Levels of BOD and concentrations of MRP, NH4(+)-N and nitrate (NO3(-)-N) of leachates were measured following dirty water applications at 2 and 8 mm day(-1) under laboratory conditions. Under the daily 2mm application, all soils were effective at treating dirty water, reducing concentrations of BOD, MRP and NH4(+)- N by > or = 98% but NO3(-)-N concentrations increased up to 80 mg l(-1) from the 0.5 m deep lysimeters of the sandy loam over granite. Soils were less effective at reducing levels of BOD, MRP and NH4(+)- N at the 8 mm daily rate of application, with maximum NO3(-)-N concentrations of leachates of 200 mg l(-1) from disturbed soils.

[Pollution load and the first flush effect of BOD5 and COD in urban runoff of Wenzhou City].

Science.gov (United States)

Wang, Jun; Bi, Chun-juan; Chen, Zhen-lou; Zhou, Dong

2013-05-01

Four typical rainfalls were monitored in two different research areas of Wenzhou Municipality. Concentrations of BOD5 and COD in six different urban runoffs were measured. In addition the event mean concentration (EMC), M (V) curve and BOD5/COD of pollutant were calculated. The results showed that concentrations of BOD5 and COD in different urban runoffs of Wenzhou ranged from ND to 69.21 mg x L(-1) and ND to 636 mg x L(-1). Concentrations of BOD5 and COD in different urban runoffs were decreasing over time, so it is greatly significant to manage the initial runoff for reducing organic pollution. Judged by EMC of BOD5 and COD in these five rainfalls, concentrations of pollutant in some urban runoffs were out of the integrated wastewater discharge standard. If these runoffs flowed into river, it would cause environmental pressure to the next level receiving water bodies. According to the M (V) curve, the first flush effect of COD in most urban runoffs was common; while the first flush effect of BOD5 was same as that of COD. The result also showed that organic pollution was serious at the beginning of runoff. The underlying surface type could affect the concentration of BOD5 and COD in urban runoff. While the results of BOD5/COD also suggested that biodegradation was considered as one of the effective ways to decrease the pollution load of organics in urban runoff, and the best management plans (BMPs) should be selected for various urban runoff types for the treatment of organic pollution.

Reliability of BOD POD Measurements Remains High After a Short-Duration Low-Carbohydrate Diet.

Science.gov (United States)

Greer, Beau Kjerulf; Edsall, Kathleen M; Greer, Anna E

2016-04-01

The purpose of the current study was to determine whether expected changes in body weight via a 3-day low-carbohydrate (LC) diet will disrupt the reliability of air displacement plethysmography measurements via BOD POD. Twenty-four subjects recorded their typical diets for 3 days before BOD POD and 7-site skinfold analyses. Subjects were matched for lean body mass and divided into low-CHO (LC) and control (CON) groups. The LC group was given instruction intended to prevent more than 50 grams/day of carbohydrate consumption for 3 consecutive days, and the CON group replicated their previously recorded diet. Body composition measurements were repeated after dietary intervention. Test-retest reliability measures were significant (p fat percentage in both the LC and the CON groups (rs = .993 and .965, respectively). Likewise, skinfold analysis for body fat percentage reliability was high in both groups (rs = .996 and .997, respectively). There were significant differences between 1st and 2nd BOD POD measurements for body mass (72.9 ± 13.3 vs. 72.1 ± 13.0 kg [M ± SD]) and body volume (69.0 ± 12.7-68.1 ± 12.2 L) in the LC group (p .05) in BOD POD-determined body fat percentage, lean body mass, or fat mass between the 1st and 2nd trial in either group. Body composition measures via BOD POD and 7-site skinfolds remain reliable after 3 days of an LC diet despite significant decreases in body mass.

Efficiency of removal of bod5 and ss in sedimentation tanks and filters in wastewater treatment systems for coffee bean (Coffea arabica processing

Directory of Open Access Journals (Sweden)

Nelson Gutiérrez Guzmán

2014-12-01

Full Text Available n order to evaluate the current operating conditions of wastewater treatment systems of small scale coffee growers in the south of Huila a lab-scale prototype (S 1:25 was constructed. It was composed of both a sediment tank and a filter fit in series, simulating similar operating conditions used by coffee producers. Removal of biological oxygen demand (BOD5 and suspended solids (SS was performed in wastewater from coffee bean processing. A 23 factorial experimental design for the evaluation of the type of sedimentation tank, type of filter and hydraulic retention time (HRT in the sedimentation tank was employed. The results showed high removal efficiencies of suspended solid concentrations (more than 95%, and low removal efficiencies in BOD5 (about 20%. The combination of tank type 1 (square with a lower area, filter type 1 (upflow anaerobic filter – UAF and HRT of 30 hours had the highest removal efficiency.

PEMANFAATAN SPUIT BEKAS SEBAGAI MEDIA BIOFILTRASI DALAM MENURUNKAN KADAR BOD DAN COD AIR LIMBAH LAUNDRY

Directory of Open Access Journals (Sweden)

Susilawati Susilawati

2016-07-01

Full Text Available Abstract: Utilization Spuit Used As Media biofilters on Reducing levels of BOD and COD Wastewater Laundry. The aim of this study was to test the ability of the media syringe biofiltration method used in lowering levels of BOD and COD in waste water laundry Hospital Dr. Soedarso Pontianak. This research is a quasi-experimental research design with one group pretest-posttest. Laboratory results mean BOD levels before processing is 103.63 mg/L and the average after processing into 46.41 mg/ L, with a value of 55.21 % effectiveness. While the average COD level before processing is 413.70 mg / L and the average after processing into a 195.88 mg/L with a value of 45.92% effectiveness. Expected to other researchers to control the pH and blowers before treatment and during treatment, as it will affect the final result. Abstrak : Pemanfaatan Spuit Bekas Sebagai Media Biofiltrasi Dalam Menurunkan Kadar BOD dan COD Air Limbah Laundry. Tujuan dari penelitian ini untuk menguji kemampuan metode biofiltrasi dengan media spuit bekas pakai dalam menurunkan kadar BOD dan COD pada air limbah laundry RSUD Dr. Soedarso Pontianak. Penelitian ini merupakan penelitian eksperimen semu dengan rancangan penelitian one group pre test post test. Hasil laboratorium rata-rata kadar BOD sebelum pengolahan yaitu 103.63 mg/L dan rata-rata setelah pengolahan menjadi 46.41 mg/L, dengan nilai efektivitas 55,21 %. Sedangkan rata-rata kadar COD sebelum pengolahan yaitu 413.70 mg/L dan rata-rata setelah pengolahan menjadi 195.88 mg/L dengan nilai efektivitas 45,92 %. Diharapkan kepada peneliti lain untuk mengontrol pH dan blower sebelum perlakuan dan pada saat perlakuan, jika melakukan penelitian sejenis karena akan mempengaruhi hasil akhir.

201-IJBCS-Article-Dr S O Ayoola

African Journals Online (AJOL)

RHUMSIKI

Seasonal variation in fish distribution and physico-chemical parameters of wetland areas in Oyo ... The water pH, Biological Oxygen Demand (BOD) and Chemical Oxygen Demand ..... that low pH creates a stress situation in most organisms ...

PHYSICO-CHEMICAL EVALUATION OF AN EFFLUENT TREATED IN ANAEROBIC BIODIGESTER REGARDING ITS EFFICIENCE AND APPLICATION AS FERTILIZER

OpenAIRE

Lopes da Silva, Wilson Tadeu; de Novaes, Antonio Pereira; Kuroki, Vivian; de Almeida Martelli, Lilian Fernanda; Magnoni Junior, Lourenco

2012-01-01

PHYSICO-CHEMICAL EVALUATION OF AN EFFLUENT TREATED IN ANAEROBIC BIODIGESTER REGARDING ITS EFFICIENCE AND APPLICATION AS FERTILIZER. The use of biodigester for basic and environmental sanitation has large demand in Brazil. A biodigester was built to treat conjunctly the human and pig feces and urine, regarding to its future application in rural small towns. The results show that the biodigester can reduce 90% of COD and BOD and, up to 99.99% of thermotolerant coliforms. The treated effluent ha...

Mineral dust emission from the Bodélé Depression, northern Chad, during BoDEx 2005

Science.gov (United States)

Todd, Martin C.; Washington, Richard; Martins, José Vanderlei; Dubovik, Oleg; Lizcano, Gil; M'bainayel, Samuel; Engelstaedter, Sebastian

2007-03-01

Mineral dust in the atmosphere is an important component of the climate system but is poorly quantified. The Bodélé Depression of northern Chad stands out as the world's greatest source region of mineral dust into the atmosphere. Frequent dust plumes are a distinguishing feature of the region's climate. There is a need for more detailed information on processes of dust emission/transport and dust optical properties to inform model simulations of this source. During the Bodélé Dust Experiment (BoDEx) in 2005, instrumentation was deployed to measure dust properties and boundary layer meteorology. Observations indicate that dust emission events are triggered when near-surface wind speeds exceed 10 ms-1, associated with synoptic-scale variability in the large-scale atmospheric circulation. Dust emission pulses in phase with the diurnal cycle of near-surface winds. Analysis of dust samples shows that the dust consists predominantly of fragments of diatomite sediment. The particle size distribution of this diatomite dust estimated from sun photometer data, using a modified Aeronet retrieval algorithm, indicates a dominant coarse mode (radius centered on 1-2 μm) similar to other Saharan dust observations. Single-scattering albedo values are high, broadly in line with other Saharan dust even though the diatomite composition of dust from the Bodélé is likely to be unusual. The radiative impact of high dust loadings results in a reduction in surface daytime maximum temperature of around 7°C in the Bodélé region. Using optical and physical properties of dust obtained in the field, we estimate the total dust flux emitted from the Bodélé to be 1.18 ± 0.45 Tg per day during a substantial dust event. We speculate that the Bodélé Depression (˜10,800 km2) may be responsible for between 6-18% of global dust emissions, although the uncertainty in both the Bodélé and global estimates remains high.

Reduction Colour and BOD of Textile Waste by Carbon-TiO2

International Nuclear Information System (INIS)

Budi Setiawan; Rosyidin; Nurimaniwathy

2007-01-01

The Granule Forming of Carbon adsorbent has been done with 5, 10, 15% of TiO 2 using the variation of adhesive materials on 110, 130, and 150 °C with diameter of 0.5 and 1 cm. The adsorbent materials was used to media of color levels absorption and BOD level on textile waste product by using stirring methods. The variation of stirring 20, 40 and 60 minutes. The result showed that the best materials condition and process were fox glue on 110 °C, stirring time at 60 minutes at 15% TiO 2 , which potent to adsorb colours level 29.608% and BOD level 66.157%. (author)

Application of Microbial BOD Sensors in Marine Monitoring

Institute of Scientific and Technical Information of China (English)

张悦; 王建龙; 李花子; 施汉昌; 竺建荣

2001-01-01

A strain of yeast, which can endure high osmotic pressure, is employed for the sensitive material of the microbial BOD sensor. Two immobilization methods are used, I.e. Calcium alginate gel be ads and PV A gel beads. The results show that the PVA gel beads is better. The influences of osmosis and heavy metal ions on the yeast entrapped in the PVA gel beads are also studied in the experiment.

Demand and supply of hydrogen as chemical feedstock in USA

Science.gov (United States)

Huang, C. J.; Tang, K.; Kelley, J. H.; Berger, B. J.

1979-01-01

Projections are made for the demand and supply of hydrogen as chemical feedstock in USA. Industrial sectors considered are petroleum refining, ammonia synthesis, methanol production, isocyanate manufacture, edible oil processing, coal liquefaction, fuel cell electricity generation, and direct iron reduction. Presently, almost all the hydrogen required is produced by reforming of natural gas or petroleum fractions. Specific needs and emphases are recommended for future research and development to produce hydrogen from other sources to meet the requirements of these industrial sectors. The data and the recommendations summarized in this paper are based on the Workshop 'Supply and Demand of Hydrogen as Chemical Feedstock' held at the University of Houston on December 12-14, 1977.

Studies on the kinetics and intraparticle diffusivities of BOD, colour ...

African Journals Online (AJOL)

EJIRO

The kinetics and intraparticle diffusivities of BOD, TSS and colour reduction from palm oil mill effluent (POME) using ... discharged (Asia et al., 2006). The oil palm ... biological treatment methods, anaerobic digestion is often the most ... and lower capital cost. ... was then rinsed with distilled water and air dried, ready for the.

Stream Macroinvertebrate Occurrence along Gradients in Organic Pollution and Eutrophication

DEFF Research Database (Denmark)

Friberg, Nikolai; Skriver, Jens; Larsen, Søren Erik

2010-01-01

We analysed a large number of concurrent samples of macroinvertebrate communities and chemical indicators of eutrophication and organic pollution [total-P, total-N, NH4-N, biological oxygen demand (BOD5)] from 594 Danish stream sites. Samples were taken over an 11-year time span as part of the Da......We analysed a large number of concurrent samples of macroinvertebrate communities and chemical indicators of eutrophication and organic pollution [total-P, total-N, NH4-N, biological oxygen demand (BOD5)] from 594 Danish stream sites. Samples were taken over an 11-year time span as part...

Zależność bodźcowości ciśnienia od cyrkulacji atmosferycznej w Warszawie

Directory of Open Access Journals (Sweden)

Katarzyna Rozbicka

2016-09-01

Full Text Available W pracy zbadano: czasowy rozkład ciśnienia atmosferycznego, bodźcowe oddziaływanie ciśnienia atmosferycznego o wartościach wyższych od 1015 hPa lub niższych od 985 hPa. Wyznaczono częstość i prawdopodobieństwo wystąpienia ciśnienia o oddziaływaniu bodźcowym oraz zanalizowano zależność zmian międzydobowych ciśnienia od typów cyrkulacji atmosferycznej według klasyfikacji Lityńskiego. Do obliczeń wykorzystano cogodzinne wartości ciśnienia atmosferycznego pochodzące ze stacji Ursynów SGGW z okresu 2011–2015. Na podstawie badań stwierdzono, że ciśnienie atmosferyczne o oddziaływaniu bodźcowym w Warszawie może wystąpić w każdym miesiącu z prawdopodobieństwem od 0,2% do 19,1%, w przypadku ciśnienia o wartościach wyższych niż 1015 hPa oraz od 0,1 do 3,4%, w przypadku ciśnienia niższego od 985 hPa, z wyjątkiem czerwca i sierpnia. Zmiany międzydobowe ciśnienia atmosferycznego mogą osiągać około 24 hPa, a częstość występowania bodźców „silnych” wywołanych tymi zmianami wyniosła w poszczególnych miesiącach od 1% do 16%, natomiast bodźców „bardzo silnych” od 2% do 8%. Spośród sytuacji synoptycznych największe znaczenie dla bodźcowości zmian ciśnienia mają sytuacje cyklonalne: szczególnie przy adwekcji powietrza z sektora północno-zachodniego (NWC.

Studies on the kinetics and intraparticle diffusivities of BOD, colour ...

African Journals Online (AJOL)

Therefore, this study reveals that boiler fly ash can effectively be used as an adsorbent for POME treatment and also established the kinetic and mechanisms of the sorption process. Also, the results of this study could serve as effective design parameters for a treatment plant to further reduce BOD, colour and TSS from ...

Effect of ozonation on microbial fish pathogens, ammonia, nitrate, nitrite, and bod in simulated reuse hatchery water

Energy Technology Data Exchange (ETDEWEB)

Colberg, P.J.; Lingg, A.J.

1978-10-01

The effectiveness of ozone for eliminating fish pathogens and reducing nitrite, ammonia, and BOD associated with reuse hatchery systems was evaluated. Comparative survival rates of four bacterial fish pathogens and a bacterium-protozoan population during batch and continuous flow ozonation indicated a specific microbial ozone demand during batch treatment and 99% mortality of pathogens during continuous flow treatment. Oxidation of carbon and nitrite by ozone was rapid at low ozone concentrations; carbon and ammonia oxidation rates were pH dependent. The oxidation capacity of ozone in water was greatest at elevated pH even though lower ozone concentrations were used. Ozone treatment appears to be successful for disinfecting hatchery makeup water for recycling. However, the economics of such treatment are yet to be determined. (10 graphs, 28 references, 1 table)

The supply and demand for pollution control: Evidence from wastewater treatment

Science.gov (United States)

McConnell, V.D.; Schwarz, G.E.

1992-01-01

This paper analyzes the determination of pollution control from wastewater treatment plants as an economic decision facing local or regional regulators. Pollution control is measured by plant design effluent concentration levels and is fully endogenous in a supply- and-demand model of treatment choice. On the supply side, plant costs are a function of the design treatment level of the plant, and on the demand side, treatment level is a function of both the costs of control and the regional or regulatory preferences for control. We find evidence that the economic model of effluent choice by local regulators has a good deal of explanatory power. We find evidence that wastewater treatment plant removal of biological oxygen demand (BOD) is sensitive to many local factors including the size of the treatment plant, the flow rate of the receiving water, the population density of the surrounding area, regional growth, state sensitivity to environmental issues, state income, and the extent to which the damages from pollution fall on other states. We find strong evidence that regulators are sensitive to capital costs in determining the design level of BOD effluent reduction at a plant. Thus, proposed reductions in federal subsidies for wastewater treatment plant construction are likely to have significant adverse effects on water quality. ?? 1992.

Burden of disease calculation, cost of illness analysis and demand ...

African Journals Online (AJOL)

The paper introduces the demand for death for Activities of Daily Living (ADL) measured disability as being pioneered by Igberaese and co-workers, as a way of eliminating the BoD and CoI once and for all. It makes DALY only equal to YLL, as YLD approaches zero. DALY will simply be the number of years of life lost due to ...

Effects of acute and 2-hour postphysical activity on the estimation of body fat made by the bod pod.

Science.gov (United States)

Harrop, Bradley J; Woodruff, Sarah J

2015-06-01

The Bod Pod has been found to be reliable/valid against several criterion methods, including hydrostatic weighing and dual-energy x-ray absorptiometry, and under different conditions, such as clothing, dehydrated states, and body temperature changes. However, questions remain regarding the effects of an acute bout of exercise. Therefore, the purpose was to determine the effects of an acute bout of exercise on the estimations made by the Bod Pod. Participants (15 men and 22 women) were of age 18-27 years and were currently exercising. Baseline Bod Pod measures were completed followed by a 30-minute cycling trial at 75% of maximum heart rate. Bod Pod measures were taken immediately after exercise and 2 hours after exercise. Differences between men and women were found at baseline between height (p temperature (p temperature (p estimate of %BF, and continues to affect the prediction 2 hours after exercise in women.

Biological treatment of textile mill wastewater in the. presence of activated carbon

International Nuclear Information System (INIS)

Liaquat, F.; Hassan, M.; Mahboob, S.; Rehman, A.; Liaquat, S.; Khalid, Z.M.

2005-01-01

The main goal of this study was to find out effectiveness of biological treatment for the reduction in chemical oxygen demand (COD) and biological oxygen demand (BOD) of the textile processing industrial wastewater in the absence and presence of granular activated carbon (GAC) in shake flask experiment. To check the pollution level, physio-chemical analysis of effluent from Amtex industry (Faisalabad) was carried out. The outlet effluent contained high value of COD (1100 mg/l), BOD (309 mg/l) with pH 9.2, electrical conductivity (Ec) 3.7 mS/m, total dissolved solids (TDS) (2640 mg/l), total solids (TS) (3060 mg/l), total suspended solids (TSS) (420 19/l) and phenol (.34 mg/l). After initial period of activated sludge adaptation to wastewater, shake flask batch cultures (with and without activated carbon) were operated on lab scale. The COD and BOD were noted after very 12 hours for 3 days. The maximum reduction in COD (82%) and BOD (90%) was observed biological treatment in presence of activated carbon at retention time of 72 hours. (author)

Effect of Lakhara chemical power station (LPTS) effluents on the river Indus water quality

International Nuclear Information System (INIS)

Mahar, R.B.; Memon, H.M.; Khushwar, M.Y.

2000-01-01

The variation of the quality of river Indus water with respect to the seasonal changes, discharge of water and dilution with the effluents of Lakhra Thermal Power Station (LTPS), has been monitored. The studies were focussed on the river Indus water quality before and after mixing the effluents of the power station. The samples were collected monthly from the representative locations of the river Indus, and analyzed for the residues (total, filterable, non-filterable, volatile and fixed), pH, temperature (air and water), conductance, chloride, hardness, alkalinity, dissolved oxygen (DO), chemical oxygen demand (COD), biochemical oxygen demand (BOD) /sub 5/- nitrate, phosphate, sulfate, ammonia, ammonium, silicates, magnesium, potassium, calcium and sodium. The results have been compared with the permissible limits of ECC (European Economic Community) standards for drinking and surface water. (author)

Analysis of tannery effluents from the Challawa industrial estate in ...

African Journals Online (AJOL)

Global Journal of Pure and Applied Sciences ... and some physicochemical parameters such as conductivity, solids, chloride, chromium, alkalinity, sulphide, chemical oxygen demand, COD, and biochemical oxygen demand, BOD, of the waste water were determined. ... Keywords: tannery, effluent, pollution, environment

Chemical Industry Waste water Treatment

International Nuclear Information System (INIS)

Nasr, F.A.; Doma, H.S.; El-Shafai, S.A.; Abdel-HaJim, H.S.

2004-01-01

Treatment of chemical industrial wastewater from building and construction chemicals factory and plastic shoes manufacturing factory was investigated. The two factories discharge their wastewater into the public sewerage network. The results showed the wastewater discharged from the building and construction chemicals factory was highly contaminated with organic compounds. The average values of COD and BOD were 2912 and 150 mg O 2 /l. Phenol concentration up to 0.3 mg/l was detected. Chemical treatment using lime aided with ferric chloride proved to be effective and produced an effluent characteristics in compliance with Egyptian permissible limits. With respect to the other factory, industrial wastewater was mixed with domestic wastewater in order to lower the organic load. The COD, BOD values after mixing reached 5239 and 2615 mg O 2 /l. The average concentration of phenol was 0.5 mg/l. Biological treatment using activated sludge or rotating biological contactor (RBe) proved to be an effective treatment system in terms of producing an effluent characteristic within the permissible limits set by the law

Biodegradation of BOD and ammonia-free using bacterial consortium in aerated fixed film bioreactor (AF2B)

Science.gov (United States)

Prayitno, Rulianah, Sri; Saroso, Hadi; Meilany, Diah

2017-06-01

BOD and Ammonia-free (NH3-N) are pollutants of hospital wastewater which often exceed the quality standards. It is because biological processes in wastewater treatment plant (WWTP) have not been effective in degrading BOD and NH3-N. Therefore, a study on factors that influence the biodegradation of BOD and NH3-N by choosing the type of bacteria to improve the mechanisms of biodegradation processes is required. Bacterial consortium is a collection of several types of bacteria obtained from isolation process, which is known to be more effective than a single bacterial in degrading pollutants. On the other hand, AF2B is a type of reactor in wastewater treatment system. The AF2B contains a filter media that has a large surface area so that the biodegradation process of pollutants by microorganism can be improved. The objective of this research is to determine the effect of volume of starter and air supplies on decreasing BOD and NH3-N in hospital wastewater using bacterial consortium in the AF2B on batch process. The research was conducted in three stages: the making of the growth curve of the bacterial consortium, bacterial consortium acclimatization, and hospital wastewater treatment in the AF2B with batch process. The variables used are the volume of starter (65%, 75%, and 85% in volume) and air supplies (2.5, 5, and 7.5 L/min). Meanwhile, the materials used are hospital wastewater, bacterial consortium (Pseudomonas diminuta, Pseudomonas capica, Bacillius sp, and Nitrobacter sp), blower, and AF2B. AF2B is a plastic basin containing a filter media with a wasp-nest shape used as a medium for growing the bacterial consortium. In the process of making the growth curve, a solid form of bacterial consortium was dissolved in sterilized water, then grown in a nutrient broth (NB). Then, shaking and sampling were done at any time to determine the path growth of bacterial consortium. In the acclimatization process, bacterial isolates were grown using hospital wastewater as a

Heavy Metal Levels and Physico-Chemical Quality of Potable Water Supply in Warri, Nigeria

International Nuclear Information System (INIS)

Nduka, K.C.; Orisakwe, E.O.

2007-01-01

The interaction between man's activities and the environment is gaining world wide attention. Warri an oil producing community in Delta State of Nigeria is faced with environmental oil pollution. Since open and underground water bodies are regarded as final recipients of most environmental pollutants, this study sought to provide data on the levels of the physico-chemical parameters and contaminants in Warri metropolitan water supply. This study investigated the cadmium, lead and chromium using Atomic Absorption Spectrophotometer, physico - chemical properties such as pH, temperature, total suspended solid TSS, total dissolved solid TDS, electrical conductivity EC, biological oxygen demand BOD, dissolved oxygen DO, chemical oxygen demand COD, and total coliform count of potable water sources in Warri. Ekpan River was found to have 1.2 mg/L of cadmium, 1.0mg/L of chromium, 1.20 mg/L of lead and 2.0 mg/L of manganese. The heavy metals levels and the pollution parameters were lowest in the borehole water samples, except pH which is more acidic in borehole water samples and conductivity which is more in well water samples in all the sampling stations. Some of the parameters were above WHO standards

Wastewater treatment of chemical laboratory using electro assisted-phytoremediation (EAPR)

Science.gov (United States)

Putra, Rudy Syah; Trahadinata, Gilang Ahmad; Latif, Arif; Solehudin, Mochamad

2017-03-01

The EAPR process using water hyacinth (Eichornia crassipes) on the wastewater treatment of chemical laboratory had been evaluated. The purpose of the EAPR process was to decrease the BOD, COD and heavy metal concentration in the wastewater. The effectiveness of the process on the wastewater treatment was evaluated using COD, BOD, and heavy metal (Pb, Cu) concentration, respectively. The result showed that the EAPR process decrease the COD, BOD, Pb and Cu in the 4 h of EAPR process. Those concentrations were met the water quality standard of class IV according to government regulation No. 82/2001 regarding the water quality management and water pollution control of the Republic of Indonesia.

Enhanced response of microbial fuel cell using sulfonated poly ether ether ketone membrane as a biochemical oxygen demand sensor

Energy Technology Data Exchange (ETDEWEB)

Ayyaru, Sivasankaran; Dharmalingam, Sangeetha, E-mail: sangeetha@annauniv.edu

2014-03-01

Graphical abstract: - Highlights: • Sulfonated poly ether ether ketone (SPEEK) membrane in SCMFC used to determine the BOD. • The biosensor produces a good linear relationship with the BOD concentration up to 650 ppm. • This sensing range was 62.5% higher than that of Nafion{sup ®}. • SPEEK exhibited one order lesser oxygen permeability than Nafion{sup ®}. • Nafion{sup ®} shows high anodic internal resistance (67 Ω) than the SPEEK (39 Ω). - Abstract: The present study is focused on the development of single chamber microbial fuel cell (SCMFC) using sulfonated poly ether ether ketone (SPEEK) membrane to determine the biochemical oxygen demand (BOD) matter present in artificial wastewater (AW). The biosensor produces a good linear relationship with the BOD concentration up to 650 ppm when using artificial wastewater. This sensing range was 62.5% higher than that of Nafion{sup ®}. The most serious problem in using MFC as a BOD sensor is the oxygen diffusion into the anode compartment, which consumes electrons in the anode compartment, thereby reducing the coulomb yield and reducing the electrical signal from the MFC. SPEEK exhibited one order lesser oxygen permeability than Nafion{sup ®}, resulting in low internal resistance and substrate loss, thus improving the sensing range of BOD. The system was further improved by making a double membrane electrode assembly (MEA) with an increased electrode surface area which provide high surface area for electrically active bacteria.

Determination of Biochemical Oxygen Demand of Area Waters: A Bioassay Procedure for Environmental Monitoring

Science.gov (United States)

Riehl, Matthew

2012-01-01

A graphical method for determining the 5-day biochemical oxygen demand (BOD5) for a body of water is described. In this bioassay, students collect a sample of water from a designated site, transport it to the laboratory, and evaluate the amount of oxygen consumed by naturally occurring bacteria during a 5-day incubation period. An accuracy check,…

Enraizamento de estacas lenhosas de pereira tratadas com AIB e mantidas em ambiente de estufa tipo B.O.D. e de telado Rooting of hardwood cuttings of pear tree with IBA under B.O.D. chamber and greenhouse environment

Directory of Open Access Journals (Sweden)

Wilson Barbosa

2007-01-01

Full Text Available Pesquisou-se o enraizamento da pereira em ambiente controlado de estufa tipo B.O.D. e em telado simples. Utilizou-se a cultivar híbrida 'Limeira', destinada exclusivamente para fins culinários e para porta-enxerto. Estacas lenhosas sem folhas, medindo 25 cm de comprimento, foram tratadas com ácido indolbutírico (AIB nas concentrações de 0; 2.000; 4.000 e 6.000 mg.L-1 por 10 segundos. Como substrato, utilizou-se da mistura de vermiculita e areia grossa (2:1 v/v, sendo a mesma umedecida com meio contendo solução salina MS e sacarose 1%. As estacas permaneceram por 42 dias dentro de estufas tipo B.O.D. (temperatura de 25ºC, umidade relativa do ar de 90% e fotoperíodo de 8 horas e de telado com irrigação por microaspersão, sem controle ambiental. Em ambiente controlado de estufa, as estacas não-tratadas com AIB iniciaram intensa brotação das gemas e formação de calo após sete dias do plantio. Já em ambiente de telado, essas estacas demoraram 21 dias para o início de brotação das gemas, mostrando menor desenvolvimento de calo. Nas estacas tratadas com AIB, os calos surgiram nas regiões dos cortes após o terceiro dia de incubação na estufa B.O.D. As raízes desenvolveram-se a partir dos tecidos da base e dos calos, tornando-se mais nítidas a partir de 14 e 28 dias, respectivamente, para os ambientes de estufa e de telado. Após 42 dias, o melhor percentual de enraizamento (83% foi verificado no tratamento com AIB a 2.000 mg.L-1, em ambiente de estufa B.O.D. O emprego dessa estufa, com temperatura, luz e umidade relativa controladas, mostrou-se viável em relação ao telado, no processo de enraizamento das estacas lenhosas da pereira 'Limeira', podendo favorecer o sistema de propagação vegetativa da pereira e encurtar o período da formação de mudas.The rooting of cuttings pear under controlled environment of chamber (B.O.D. type and greenhouse was searched. Hardwood cuttings of 'Limeira' pear, without leaves, measuring

Pengaruh Laju Alir Inlet Reaktor MSL terhadap Reduksi BOD, COD, TSS, dan Minyak/Lemak Limbah Cair Industri Minyak Goreng

Directory of Open Access Journals (Sweden)

Salmariza Sy

2017-06-01

Full Text Available This research was conducted by treating edible oil industry wastewater used Multi Soil Layering (MSL method. The MSL reactor was built from a 200x120x200 cm concrete basin. Andisol soil was mixed with sawdust and fine charcoal at each ratio 5:1:1 based on dry weight as an impermeable layer. The flow rate variations were 250, 500, 1000, and 1500 L/m2.day. The observed pollutant parameters were BOD, COD, TSS, oil/fat, and pH. The results showed that MSL reactor was effective to decrease the pollutant content of edible oil industry wastewater. The reactor could reduce concentration of effluent parameters below standard except for oil/fat parameters at high flow rates. In the effluent was found BOD 0.66-14.22 mg/L, COD 5-69 mg/L, TSS 9-26 mg/L, and oil/fat 2-9 mg/L. The flow rate had an effect on reduction efficiency of BOD, COD, TSS, and oil/fat but did not effect pH as all flow rate could raise pH 6.37-6.95 became pH 6.99-7.24. The lower the flow rate the higher the reduction efficiency. The reduction efficiency at flow rates 250 and 1500 L/m2 days for BOD were 99% and 86%, COD were 96% and 71%, TSS were 88% and 77%, and oil/fat were 80% and 60%.ABSTRAK  Penelitian ini dilakukan dengan mengolah air limbah industri minyak goreng menggunakan metoda Multi Soil Layering (MSL. Reaktor MSL dibuat dari beton berbentuk bak ukuran 200x120x200 cm. Tanah andisol dicampur dengan serbuk gergaji dan arang halus pada rasio masing-masing 5:1:1 berdasarkan berat kering sebagai penyusun lapisan impermeable. Variasi laju alir yaitu 250, 500, 1000, dan 1500 L/m2.hari. Parameter pencemar yang dianalisis meliputi BOD, COD, TSS, minyak/lemak, dan pH. Hasil penelitian menunjukkan bahwa reaktor MSL sangat efektif untuk menurunkan kandungan zat pencemar limbah cair industri minyak goreng. Reaktor dapat mereduksi konsentrasi parameter outlet sampai dibawah baku mutu yang distandarkan kecuali untuk parameter miyak/lemak pada perlakuan laju alir tinggi. Pada effluen

Pollution control in pulp and paper industrial effluents using integrated chemical-biological treatment sequences.

Science.gov (United States)

El-Bestawy, Ebtesam; El-Sokkary, Ibrahim; Hussein, Hany; Keela, Alaa Farouk Abu

2008-11-01

The main objective of the present study was to improve the quality of pulp and paper industrial wastewater of two local mills RAKTA and El-Ahlia, Alexandria, Egypt, and to bring their pollutant contents to safe discharge levels. Quality improvement was carried out using integrated chemical and biological treatment approaches after their optimization. Chemical treatment (alum, lime, and ferric chloride) was followed by oxidation using hydrogen peroxide and finally biological treatment using activated sludge (90 min for RAKTA and 60 min for El-Ahlia effluents). Chemical coagulation produced low-quality effluents, while pH adjustment during coagulation treatment did not enhance the quality of the effluents. Maximum removal of the tested pollutants was achieved using the integrated treatment and the pollutants recorded residual concentrations (RCs) of 34.67, 17.33, 0.13, and 0.43 mg/l and 15.0, 11.0, 0.0, and 0.13 mg/l for chemical oxygen demand (COD), biochemical oxygen demand (BOD5), tannin and lignin, and silica in RAKTA and El-Ahlia effluents, respectively, all of which were below their maximum permissible limits (MPLs) for the safe discharge into water courses. Specific oxygen uptake rate (SOUR) and sludge volume index (SVI) values reflect good conditions and healthy activated sludge. Based on the previous results, optimized conditions were applied as bench scale on the raw effluents of RAKTA and El-Ahlia via the batch chemical and the biological treatment sequences proposed. For RAKTA effluents, the sequence was as follows: (1) coagulation with 375 mg/l FeCl3, (2) oxidation with 50 mg/l hydrogen peroxide, and (3) biological treatment using activated sludge with 2,000 mg/l initial concentration and 90 min hydraulic retention time (HRT), while for El-Ahlia raw effluents, the sequence was (1) coagulation with 250 mg/l FeCl3, (2) oxidation with 45 mg/l hydrogen peroxide, and (3) biological treatment using activated sludge with 2,000 mg/l initial concentration and 60

Evaluation of organic matter concentration in winery wastewater: a case study from Australia.

Science.gov (United States)

Quayle, Wendy C; Fattore, Alison; Zandona, Roy; Christen, Evan W; Arienzo, Michele

2009-01-01

The 5-day biological oxygen demand (BOD(5)) remains a key indicator for proof of compliance with environmental regulators in the monitoring and management of winery effluent. Inter-conversion factors from alternative tests that are more rapid, accurate and simpler to perform have been determined that allow prediction of BOD(5) in winery wastewaters, generally, and at different stages of production and treatment. Mean values obtained from this dataset offer rule of thumb inter-conversion factors: BOD(5) = 0.7 Chemical Oxygen Demand (COD), BOD(5) = 2.3 Total Organic Carbon (TOC) and BOD(5) = 2.7 Dissolved Organic Carbon (DOC). Specific predictive linear relationships are also provided. Out of the relationships between BOD(5) vs COD, TOC and DOC, in winery wastewater, irrespective of vintage or non-vintage production periods and stage of treatment, TOC offered the most reliable prediction of BOD(5). Ethanol, glucose and fructose were evaluated in untreated wastewater as predictors of BOD(5) due to their high specificity in winery effluent. A significant relationship was determined between BOD(5) and (ethanol + glucose + fructose; R(2) = 0.64, n = 19; pwinery effluents when using a commercially available mercury free test kit compared with using a traditional COD test kit that contained mercury. This suggests that mercury free COD test kits could be used by the wine industry for organic pollution assessment with associated reductions to user and environmental risk, as well as reducing the costs of kit waste disposal.

Performance Evaluation of Anaerobic-Aerobic Treatment for the Wastewater of Potato Processing Industry: A Case Study of a Local Chips Factory

International Nuclear Information System (INIS)

Haydar, S.; Nadeem, O.

2014-01-01

A study was conducted to assess the performance of anaerobic-aerobic treatment system of a local potato processing industry. The wastewater treatment plant (WWTP) consisted of primary treatment, upflow anaerobic sludge blanket (UASB), activated sludge process (ASP) and secondary clarifier. The study analyzed the physical, chemical and biochemical parameters of the influent (raw sewage) as well as the effluent from each component of the plant. Grab wastewater samples were collected on weekly basis and analyzed for the pH, settleable solids (SS), total suspended solids (TSS), total dissolved solids (TDS), biochemical oxygen demand (BOD), and chemical oxygen demand (COD). Study revealed that mean influent wastewater concentrations of TSS, TDS, SS, BOD and COD were 840 mg/L, 2,396 mg/L and 18.7 mL/L, 2,186 mg/L and 3,679 mg/L, respectively. The mean percentage removal efficiency in UASB for TSS, BOD and COD was found to be 56%, 61 % and 51%, respectively. The mean percentage removal efficiency in activated sludge system for TSS, BOD and COD was found to be 70%, 57% and 48%, respectively. The mean percentage removal efficiency of combined anaerobic-aerobic system for TSS, BOD and COD was found to be 93%, 90% and 80%, respectively. The mean effluent concentrations of TSS, BOD and COD were 52 mg/L, 197 mg/L and 784 mg/L, respectively. The effluent from WWTP satisfied NEQS for TSS (200 mg/L) while NEQS for BOD (80 mg/L) and COD (150 mg/L) were not satisfied. Some operational problems, responsible for inadequate efficiencies of the plant components, were identified and solutions were suggested for these problems. (author)

Iron oxide minerals in dust-source sediments from the Bodélé Depression, Chad: Implications for radiative properties and Fe bioavailability of dust plumes from the Sahara

Science.gov (United States)

Moskowitz, Bruce M; Reynolds, Richard L.; Goldstein, Harland L.; Beroquo, Thelma; Kokaly, Raymond F.; Bristow, Charlie S

2016-01-01

Atmospheric mineral dust can influence climate and biogeochemical cycles. An important component of mineral dust is ferric oxide minerals (hematite and goethite) which have been shown to influence strongly the optical properties of dust plumes and thus affect the radiative forcing of global dust. Here we report on the iron mineralogy of dust-source samples from the Bodélé Depression (Chad, north-central Africa), which is estimated to be Earth’s most prolific dust producer and may be a key contributor to the global radiative budget of the atmosphere as well as to long-range nutrient transport to the Amazon Basin. By using a combination of magnetic property measurements, Mössbauer spectroscopy, reflectance spectroscopy, chemical analysis, and scanning electron microscopy, we document the abundance and relative amounts of goethite, hematite, and magnetite in dust-source samples from the Bodélé Depression. The partition between hematite and goethite is important to know to improve models for the radiative effects of ferric oxide minerals in mineral dust aerosols. The combination of methods shows (1) the dominance of goethite over hematite in the source sediments, (2) the abundance and occurrences of their nanosize components, and (3) the ubiquity of magnetite, albeit in small amounts. Dominant goethite and subordinate hematite together compose about 2% of yellow-reddish dust-source sediments from the Bodélé Depression and contribute strongly to diminution of reflectance in bulk samples. These observations imply that dust plumes from the Bodélé Depression that are derived from goethite-dominated sediments strongly absorb solar radiation. The presence of ubiquitous magnetite (0.002–0.57 wt%) is also noteworthy for its potentially higher solubility relative to ferric oxide and for its small sizes, including PM bioavailability to marine and terrestrial ecosystems.

Hollow-fiber membrane bioreactor for the treatment of high-strength landfill leachate

KAUST Repository

Rizkallah, Marwan; El-Fadel, Mutasem E.; Saikaly, Pascal; Ayoub, George M.; Darwiche, Nadine D.; Hashisho, Jihan

2013-01-01

-fiber MBR. For this purpose, a laboratory-scale MBR was constructed and operated to treat leachate with a chemical oxygen demand (COD) of 9000-11,000 mg/l, a 5-day biochemical oxygen demand (BOD5) of 4000-6,000 mg/l, volatile suspended solids (VSS) of 300

Influence of Hudiara Drain Water Irrigation on Trace Elements Load ...

African Journals Online (AJOL)

... Drain Water Irrigation on Trace Elements Load In Soil And Uptake By Vegetables. ... This polluted water not only contains organic matter and crop nutrients but also ... Plant samples were collected at maturity from all the monitoring points. ... (DO), Chemical Oxygen Demand (COD) and Biological Oxygen Demand (BOD) ...

A comparative study of technologies for the continuous measurements of the biochemical demand for oxygen and toxicity of water; Estudio comparativo de tecnologias de medicion en continuo de la demanda bioquimica de oxigeno y de la toxicidad en aguas

Energy Technology Data Exchange (ETDEWEB)

Diez-Caballero Arnau, T.; Rodriguez Albalat, G.; Rosa de la Garcia, S.; Jimenez Bono, M.; Millan Navarro, C.; prats, R.; Serramia, A.; Miguel, S. de

2002-07-01

The Prevention and Integrated Control of Contamination Act (Ley de Prevencion y control Integrado de la Contaminacion) was passed by the Spanish parliament on 13 June. the basic purpose of this law is to prevent, reduce and control contamination of the atmosphere, water and soil caused by the most contaminating industrial activities. Public sector bodies and private companies in Spanish have been invited by the European Union to adopt new technologies in their production processes with a view to cutting down emissions, minimising or re-using waste, and pre-treating or purifying effluents. I t is therefore extremely appropriate to make available information on new tools of analysis that allow users to take preventive measures to reduce the impact their activity may have on the environment. A fundamental parameter in monitoring water is the Biological Demand for Oxygen (BOD). Various different chemical, physical and biological techniques have been developed to solve the problem of continuously monitoring the BOD and toxicity of water. This study carried out a comparative analysis of these techniques, describing the advantages and disadvantages of applying them to water quality control. At the present time it can be said that the BOD microbiosensor. Multisens 304 is the best available technology for monitoring this parameter. The articles tells us why. (Author) 8 refs.

Iron oxide minerals in dust-source sediments from the Bodélé Depression, Chad: Implications for radiative properties and Fe bioavailability of dust plumes from the Sahara

Science.gov (United States)

Moskowitz, Bruce M; Reynolds, Richard L.; Goldstein, Harland L.; Beroquo, Thelma; Kokaly, Raymond F.; Bristow, Charlie S

2016-01-01

Atmospheric mineral dust can influence climate and biogeochemical cycles. An important component of mineral dust is ferric oxide minerals (hematite and goethite) which have been shown to influence strongly the optical properties of dust plumes and thus affect the radiative forcing of global dust. Here we report on the iron mineralogy of dust-source samples from the Bodélé Depression (Chad, north-central Africa), which is estimated to be Earth’s most prolific dust producer and may be a key contributor to the global radiative budget of the atmosphere as well as to long-range nutrient transport to the Amazon Basin. By using a combination of magnetic property measurements, Mössbauer spectroscopy, reflectance spectroscopy, chemical analysis, and scanning electron microscopy, we document the abundance and relative amounts of goethite, hematite, and magnetite in dust-source samples from the Bodélé Depression. The partition between hematite and goethite is important to know to improve models for the radiative effects of ferric oxide minerals in mineral dust aerosols. The combination of methods shows (1) the dominance of goethite over hematite in the source sediments, (2) the abundance and occurrences of their nanosize components, and (3) the ubiquity of magnetite, albeit in small amounts. Dominant goethite and subordinate hematite together compose about 2% of yellow-reddish dust-source sediments from the Bodélé Depression and contribute strongly to diminution of reflectance in bulk samples. These observations imply that dust plumes from the Bodélé Depression that are derived from goethite-dominated sediments strongly absorb solar radiation. The presence of ubiquitous magnetite (0.002–0.57 wt%) is also noteworthy for its potentially higher solubility relative to ferric oxide and for its small sizes, including PM iron apportionment is estimated at about 33% in ferric oxide minerals, 1.4% in magnetite, and 65% in ferric silicates. Structural iron in clay

The influence of ozonated time on the degree of depreciation of BOD, COD, TSS and phosphate in hospital liquid waste

International Nuclear Information System (INIS)

Isyuniarto and Andrianto

2009-01-01

The influence of ozonated time towards degree depreciation of Bode, COD, TSS and phosphate in hospital liquid waste was done. This research aim study influence of lime adding and ozone using to reduce of BOD, COD, TSS and phosphate in hospital waste. Added of lime mean for total increase ion OH - , while parameter of ozonization time mean to complete organic compounds oxidation in waste and flock formation. From this research it was found that optimum lime addition was 1.1% (% weight) and ozonization time was 20 minutes. In this condition it was achieved degree of BOD = 18.88 mg/l; COD = 25.68 mg/l, TSS = 80 mg/l and phosphate = 1.52 mg/l. This condition fulfil quality standard decided, that has to BOD = 75 mg/l; COD = 100 mg/l, TSS = 100 mg/l and phosphate = 2.0 mg/l. (author)

The chemical and biological characteristics of coke-oven wastewater by ozonation

International Nuclear Information System (INIS)

Chang, E.-E.; Hsing, H.-J.; Chiang, P.-C.; Chen, M.-Y.; Shyng, J.-Y.

2008-01-01

A bench-scale bubble column reactor was used to investigate the biological and chemical characteristics of coke-oven wastewater after ozonation treatment through the examination of selected parameters. Color and thiocyanate could be removed almost entirely; however, organic matter and cyanide could not, due to the inadequate oxidation ability of ozone to remove ozonated byproducts under given experimental conditions. The removal of cyanide and total organic carbon were pH-dependent and were found to be efficient under neutral to alkaline conditions. The removal rate for thiocyanate was about five times that of cyanide. The ozone consumption ratio approached to about 1 at the early stage of ozonation (time TOC ) increased to 30%, indicating that easily degraded pollutants were degraded almost entirely. The effect of ozonation on the subsequent biological treatment unit (i.e., activated sludge process) was determined by observing the ratio of 5-day biological oxygen demand to chemical oxygen demand (BOD 5 /COD) and the specific oxygen utilization rate (SOUR). The results indicated that the contribution of ozonation to inhibition reduction was very significant but limited to the enhancement of biodegradation. The operation for ozonation of coke-oven wastewater was feasible under neutral condition and short ozone contact time in order to achieve better performance and cost savings

Chloramine demand estimation using surrogate chemical and microbiological parameters.

Science.gov (United States)

Moradi, Sina; Liu, Sanly; Chow, Christopher W K; van Leeuwen, John; Cook, David; Drikas, Mary; Amal, Rose

2017-07-01

A model is developed to enable estimation of chloramine demand in full scale drinking water supplies based on chemical and microbiological factors that affect chloramine decay rate via nonlinear regression analysis method. The model is based on organic character (specific ultraviolet absorbance (SUVA)) of the water samples and a laboratory measure of the microbiological (F m ) decay of chloramine. The applicability of the model for estimation of chloramine residual (and hence chloramine demand) was tested on several waters from different water treatment plants in Australia through statistical test analysis between the experimental and predicted data. Results showed that the model was able to simulate and estimate chloramine demand at various times in real drinking water systems. To elucidate the loss of chloramine over the wide variation of water quality used in this study, the model incorporates both the fast and slow chloramine decay pathways. The significance of estimated fast and slow decay rate constants as the kinetic parameters of the model for three water sources in Australia was discussed. It was found that with the same water source, the kinetic parameters remain the same. This modelling approach has the potential to be used by water treatment operators as a decision support tool in order to manage chloramine disinfection. Copyright © 2017. Published by Elsevier B.V.

Transport of North African dust from the Bodélé depression to the Amazon Basin: a case study

Directory of Open Access Journals (Sweden)

Y. Ben-Ami

2010-08-01

Full Text Available Through long-range transport of dust, the North-African desert supplies essential minerals to the Amazon rain forest. Since North African dust reaches South America mostly during the Northern Hemisphere winter, the dust sources active during winter are the main contributors to the forest. Given that the Bodélé depression area in southwestern Chad is the main winter dust source, a close link is expected between the Bodélé emission patterns and volumes and the mineral supply flux to the Amazon.

Until now, the particular link between the Bodélé and the Amazon forest was based on sparse satellite measurements and modeling studies. In this study, we combine a detailed analysis of space-borne and ground data with reanalysis model data and surface measurements taken in the central Amazon during the Amazonian Aerosol Characterization Experiment (AMAZE-08 in order to explore the validity and the nature of the proposed link between the Bodélé depression and the Amazon forest.

This case study follows the dust events of 11–16 and 18–27 February 2008, from the emission in the Bodélé over West Africa (most likely with contribution from other dust sources in the region the crossing of the Atlantic Ocean, to the observed effects above the Amazon canopy about 10 days after the emission. The dust was lifted by surface winds stronger than 14 m s⁻¹, usually starting early in the morning. The lofted dust, mixed with biomass burning aerosols over Nigeria, was transported over the Atlantic Ocean, and arrived over the South American continent. The top of the aerosol layer reached above 3 km, and the bottom merged with the boundary layer. The arrival of the dusty air parcel over the Amazon forest increased the average concentration of aerosol crustal elements by an order of magnitude.

Soil aquifer treatment of artificial wastewater under saturated conditions

KAUST Repository

Essandoh, H. M K; Tizaoui, Chedly; Mohamed, Mostafa H A; Amy, Gary L.; Brdjanovic, Damir

2011-01-01

A 2000 mm long saturated laboratory soil column was used to simulate soil aquifer treatment under saturated conditions to assess the removal of chemical and biochemical oxygen demand (COD and BOD), dissolved organic carbon (DOC), nitrogen

Biological oxygen demand in soils and hydrogel compositions for plant protection of the rhizosphere

Science.gov (United States)

Valentinovich Smagin, Andrey

2018-02-01

Potential biological activity of mineral and organogenic samples from light-textured sod-podzolic soils as well as of hydrogel compositions for protecting the root layer from pathogenic microflora and unfavorable edaphic factors were studied in laboratory conditions by oxygen consumption under the optimal hydrothermic conditions with portable gas analyzers. We have conducted ecological standardization of biological activity and organic matter destruction estimated by biological oxygen demand (BOD) in the widespread sandy soils. The primary outcome was the scale of gradations of biological oxygen uptake in soils with a range of quantities of potential biological activity from “very low” (140 g·m-3·hour-1), obtained on the basis of statistical processing of data array 1308 measurements. Acrylic polymer hydrogels had BOD = 0.2-2 g·m-3·hour-1, which corresponded to the periods of their half-lives from 0.2±0.1 to 6.8± 4.5 years, or relatively low resistance to biodestruction. In contrast to the pure gels, hydrogel compositions for rhizosphere based on ionic and colloidal silver showed low biological activity (BOD=0.01-0.2 g·m-3· hour-1) and, accordingly, significant resistance to biodegradation with half-lives from 5 to 70 years and above.

Electrolysis of polluting wastes: I - Wastewater from a seasoning freeze-drying industry

OpenAIRE

Angelis, Dejanira F. de; Corso, Carlos R.; Bidoia, Ederio D.; Moraes, Peterson B.; Domingos, Roberto N.; Rocha-Filho, Romeu C.

1998-01-01

Wastewater from a seasoning freeze-drying industry was electrolysed to increase its biodegradability. Stainless-steel electrodes were used at 9.09 A/m², for up to 80 min. Conductivity, pH, biochemical (BOD) and chemical (COD) oxygen demands, Daphnia similis acute toxicity bioassays, and bacteria counting through the plate count agar method were determined after different times of electrolysis. The results (e.g. higher BOD and lower COD) showed that the biodegradability of the wastewater was s...

Removal of Heavy Metals from Steel Making Waste Water by Using Electric Arc Furnace Slag

Directory of Open Access Journals (Sweden)

C. L. Beh

2012-01-01

Full Text Available This work investigated the reduction of chemical oxygen demand (COD, biological oxygen demand (BOD, total suspended solids (TSS and the concentration of heavy metals of wastewater from a steel making plant. Adsorption experiments were carried out by electric arc furnace slag (EAFS in a fixed-bed column mode. The raw wastewater did not meet the standard B limitations, having high values of BOD, COD, TSS, Iron, Zinc, Manganese and Copper. After passing through the fixed bed column, BOD, COD and TSS values decreased to 1.6, 6.3 and <2 mgL-1, respectively while the concentration of Iron, Zinc, Manganese and Copper were 0.08, 0.01, 0.03 and 0.07 mgL-1, respectively. The results confirmed that EAFS can be used as an efficient adsorbent for producing treated water that comply with the Standard B limitations for an industrial effluent.

Performance of a modified multi-stage bubble column reactor for lead(II) and biological oxygen demand removal from wastewater using activated rice husk

International Nuclear Information System (INIS)

Sahu, J.N.; Agarwal, S.; Meikap, B.C.; Biswas, M.N.

2009-01-01

The excessive release of wastewater into the environment is a major concern worldwide. Adsorption is the one of the most effective technique for treatment of wastewater. In this work activated carbon prepared from rice husk has been used as an adsorbent. In the present investigation a three phase modified multi-stage bubble column reactor (MMBCR) has been designed to remove lead and biochemical oxygen demand (BOD) from wastewater by means of its adsorption onto the surface of activated rice husk. The multi-staging has been achieved by hydrodynamically induced continuous bubble generation, breakup and regeneration. Under optimum conditions, maximum lead and BOD reduction achieved using activated rice husk was 77.15% and 19.05%, respectively. Results showed MMBCR offered appreciated potential benefits for lead removal from wastewater and BOD removal, even this extent of removal is encouraging and the MMBCR can be used a pretreatment unit before subjecting the wastewater to biological treatment

Performance of a modified multi-stage bubble column reactor for lead(II) and biological oxygen demand removal from wastewater using activated rice husk.

Science.gov (United States)

Sahu, J N; Agarwal, S; Meikap, B C; Biswas, M N

2009-01-15

The excessive release of wastewater into the environment is a major concern worldwide. Adsorption is the one of the most effective technique for treatment of wastewater. In this work activated carbon prepared from rice husk has been used as an adsorbent. In the present investigation a three phase modified multi-stage bubble column reactor (MMBCR) has been designed to remove lead and biochemical oxygen demand (BOD) from wastewater by means of its adsorption onto the surface of activated rice husk. The multi-staging has been achieved by hydrodynamically induced continuous bubble generation, breakup and regeneration. Under optimum conditions, maximum lead and BOD reduction achieved using activated rice husk was 77.15% and 19.05%, respectively. Results showed MMBCR offered appreciated potential benefits for lead removal from wastewater and BOD removal, even this extent of removal is encouraging and the MMBCR can be used a pretreatment unit before subjecting the wastewater to biological treatment.

Physico-chemical treatment of coke plant effluents for control of water pollution in India

Energy Technology Data Exchange (ETDEWEB)

Ghose, M.K. [Indian School of Mines, Dhanbad (India). Center of Mining Environmental

2002-01-01

Coal carbonizing industries in India are important and are growing every year. Large quantities of liquid effluents produced in this industry contain a large amount of suspended solids, high biochemical oxygen demand (BOD), chemical oxygen demand (COD), phenols, ammonia and other toxic substances, which are causing serious surface water pollution in the area. There is a large number of coke plants in the vicinity of Jharia Coal Field (JCF). The working principle of a coke plant and the effluents produced is described. One large coke plant was chosen to evaluate characteristics of the effluent and to suggest a proper treatment method. Present effluent treatment system was found to be inadequate and a large quantity of a very good quality coke breeze is being lost, which is also causing siltation on the riverbed in addition to surface water pollution. Physico-chemical treatment has been considered as a suitable option for the treatment of coke plant effluents. A scheme has been proposed for the treatment, which can be suitably adopted for the recycling, reuse or safe disposal of the treated effluent. Various unit process and unit operations are discussed. The process may be useful on industrial scale for various sites so as to maintain a clean environment.

Modelling soil dust aerosol in the Bodélé depression during the BoDEx campaign

Science.gov (United States)

Tegen, I.; Heinold, B.; Todd, M.; Helmert, J.; Washington, R.; Dubovik, O.

2006-09-01

We present regional model simulations of the dust emission events during the Bodélé Dust Experiment (BoDEx) that was carried out in February and March 2005 in Chad. A box model version of the dust emission model is used to test different input parameters for the emission model, and to compare the dust emissions computed with observed wind speeds to those calculated with wind speeds from the regional model simulation. While field observations indicate that dust production occurs via self-abrasion of saltating diatomite flakes in the Bodélé, the emission model based on the assumption of dust production by saltation and using observed surface wind speeds as input parameters reproduces observed dust optical thicknesses well. Although the peak wind speeds in the regional model underestimate the highest wind speeds occurring on 10-12 March 2005, the spatio-temporal evolution of the dust cloud can be reasonably well reproduced by this model. Dust aerosol interacts with solar and thermal radiation in the regional model; it is responsible for a decrease in maximum daytime temperatures by about 5 K at the beginning the dust storm on 10 March 2005. This direct radiative effect of dust aerosol accounts for about half of the measured temperature decrease compared to conditions on 8 March. Results from a global dust model suggest that the dust from the Bodélé is an important contributor to dust crossing the African Savannah region towards the Gulf of Guinea and the equatorial Atlantic, where it can contribute up to 40% to the dust optical thickness.

Chemical oxygen demand reduction in coffee wastewater through chemical flocculation and advanced oxidation processes

Institute of Scientific and Technical Information of China (English)

ZAYAS Pérez Teresa; GEISSLER Gunther; HERNANDEZ Fernando

2007-01-01

The removal of the natural organic matter present in coffee processing wastewater through chemical coagulation-flocculatio and advanced oxidation processes(AOP)had been studied.The effectiveness of the removal of natural organic matter using commercial flocculants and UV/H202,UVO3 and UV/H-H202/O3 processes was determined under acidic conditions.For each of these processes,different operational conditions were explored to optimize the treatment efficiency of the coffee wastewater.Coffee wastewater is characterized by a high chemical oxygen demand(COD)and low total suspended solids.The outcomes of coffee wastewater reeatment using coagulation-flocculation and photodegradation processes were assessed in terms of reduction of COD,color,and turbidity.It was found that a reductiOn in COD of 67%could be realized when the coffee wastewater was treated by chemical coagulation-flocculatlon witll lime and coagulant T-1.When coffee wastewater was treated by coagulation-flocculation in combination with UV/H202,a COD reduction of 86%was achieved,although only after prolonged UV irradiation.Of the three advanced oxidation processes considered,UV/H202,uv/03 and UV/H202/03,we found that the treatment with UV/H2O2/O3 was the most effective,with an efficiency of color,turbidity and further COD removal of 87%,when applied to the flocculated coffee wastewater.

Hollow-fiber membrane bioreactor for the treatment of high-strength landfill leachate

KAUST Repository

Rizkallah, Marwan

2013-07-15

Performance assessment of membrane bioreactor (MBR) technology for the treatability of high-strength landfill leachate is relatively limited or lacking. This study examines the feasibility of treating high-strength landfill leachate using a hollow-fiber MBR. For this purpose, a laboratory-scale MBR was constructed and operated to treat leachate with a chemical oxygen demand (COD) of 9000-11,000 mg/l, a 5-day biochemical oxygen demand (BOD5) of 4000-6,000 mg/l, volatile suspended solids (VSS) of 300-500 mg/l, total nitrogen (TN) of 2000-6000 mg/l, and an ammonia-nitrogen (NH3-N) of 1800-4000 mg/l. VSS was used with the BOD and COD data to simulate the biological activity in the activated sludge. Removal efficiencies > 95-99% for BOD5, VSS, TN and NH3-N were attained. The coupled experimental and simulation results contribute in filling a gap in managing high-strength landfill leachate and providing guidelines for corresponding MBR application. © The Author(s) 2013.

Characteristic of leachate at Alor Pongsu Landfill Site, Perak, Malaysia: A comparative study

Science.gov (United States)

Nor Farhana Zakaria, Siti; Aziz, Hamidi Abdul

2018-04-01

Leachate is a harmful by product generated from the landfill site. Leachate contains a high concentration of pollutant which can cause serious pollution to environmental. In this study, characteristics of leachate in Alor Pongsu Landfill Site (APLS) were monitored and analyzed according to the Standard Methods for the Examination of Water and Wastewater (2005). Composition in leachate at APLS was monitored for one year starting from January 2015 until January 2016. Nine parameters were monitored including color, chemical oxygen demand (COD), biological oxygen demand (BOD5), ammoniacal nitrogen (NH3-N), biodegradability ratio (BOD5/COD), temperature, dissolved oxygen (DO), total dissolved solid (TDS) and pH. Based on the analysis, Alor Pongsu Landfill leachate was categorized as stabilized landfill leachate by referring to the BOD5/COD < 0.1. Comparison with allowable discharge limits for leachate shows that most of parameters exceeded the standard discharge limitation. Thus, proper treatment is needed before leachate can be discharged to the environment.

A reduced-order adaptive neuro-fuzzy inference system model as a software sensor for rapid estimation of five-day biochemical oxygen demand

Science.gov (United States)

Noori, Roohollah; Safavi, Salman; Nateghi Shahrokni, Seyyed Afshin

2013-07-01

The five-day biochemical oxygen demand (BOD5) is one of the key parameters in water quality management. In this study, a novel approach, i.e., reduced-order adaptive neuro-fuzzy inference system (ROANFIS) model was developed for rapid estimation of BOD5. In addition, an uncertainty analysis of adaptive neuro-fuzzy inference system (ANFIS) and ROANFIS models was carried out based on Monte-Carlo simulation. Accuracy analysis of ANFIS and ROANFIS models based on both developed discrepancy ratio and threshold statistics revealed that the selected ROANFIS model was superior. Pearson correlation coefficient (R) and root mean square error for the best fitted ROANFIS model were 0.96 and 7.12, respectively. Furthermore, uncertainty analysis of the developed models indicated that the selected ROANFIS had less uncertainty than the ANFIS model and accurately forecasted BOD5 in the Sefidrood River Basin. Besides, the uncertainty analysis also showed that bracketed predictions by 95% confidence bound and d-factor in the testing steps for the selected ROANFIS model were 94% and 0.83, respectively.

Modelling soil dust aerosol in the Bodélé depression during the BoDEx campaign

Directory of Open Access Journals (Sweden)

I. Tegen

2006-01-01

Full Text Available We present regional model simulations of the dust emission events during the Bodélé Dust Experiment (BoDEx that was carried out in February and March 2005 in Chad. A box model version of the dust emission model is used to test different input parameters for the emission model, and to compare the dust emissions computed with observed wind speeds to those calculated with wind speeds from the regional model simulation. While field observations indicate that dust production occurs via self-abrasion of saltating diatomite flakes in the Bodélé, the emission model based on the assumption of dust production by saltation and using observed surface wind speeds as input parameters reproduces observed dust optical thicknesses well. Although the peak wind speeds in the regional model underestimate the highest wind speeds occurring on 10–12 March 2005, the spatio-temporal evolution of the dust cloud can be reasonably well reproduced by this model. Dust aerosol interacts with solar and thermal radiation in the regional model; it is responsible for a decrease in maximum daytime temperatures by about 5 K at the beginning the dust storm on 10 March 2005. This direct radiative effect of dust aerosol accounts for about half of the measured temperature decrease compared to conditions on 8 March. Results from a global dust model suggest that the dust from the Bodélé is an important contributor to dust crossing the African Savannah region towards the Gulf of Guinea and the equatorial Atlantic, where it can contribute up to 40% to the dust optical thickness.

Comparative Assessment of the Physico-Chemical and Bacteriological Qualities of Selected Streams in Louisiana

Directory of Open Access Journals (Sweden)

Paul B. Tchounwou

2005-04-01

Full Text Available The objective of this research was to compare the chemical/physical parameters and bacterial qualities of selected surface water streams in Louisiana, including a natural stream (control and an animal waste related stream. Samples were collected and analyzed for fecal coliforms. Fecal coliforms isolated from these samples were identified to the species level. Chemical analysis was performed following standard test protocols (LaMotte 2002. An analysis of biological oxygen demand (BOD, chemical oxygen demand (COD, total organic carbon (TOC, total dissolved solids (TDS, conductivity, pH, temperature, ammonia nitrogen, nitrate nitrogen, iron, copper, phosphate, potassium, sulfate, turbidity, zinc and bacterial levels was performed following standard test protocols as presented in Standard Methods for the Examination of Water and Wastewater [9]. Results of the comparisons of the various surface water streams showed that phosphate levels, according to Mitchell and Stapp, were considered good for Lake Claiborne (control and Bayou Dorcheat. The levels were found to be .001 mg/L and .007 mg/L respectively. Other streams associated with animal waste, had higher phosphate levels of 2.07 mg/L and 2.78 mg/L, respectively. Conductivity and total dissolved solids (TDS levels were the lowest in Lake Claiborne and highest in the Hill Farm Research Station stream. It can be concluded from the data that some bacterial levels and various nutrient levels can be affected in water resources due to non-point source pollution. Many of these levels will remain unaffected.

Comparative assessment of the physico-chemical and bacteriological qualities of selected streams in Louisiana.

Science.gov (United States)

Hill, Dagne D; Owens, William E; Tchounwou, Paul B

2005-04-01

The objective of this research was to compare the chemical/physical parameters and bacterial qualities of selected surface water streams in Louisiana, including a natural stream (control) and an animal waste related stream. Samples were collected and analyzed for fecal coliforms. Fecal coliforms isolated from these samples were identified to the species level. Chemical analysis was performed following standard test protocols (LaMotte 2002). An analysis of biological oxygen demand (BOD), chemical oxygen demand (COD), total organic carbon (TOC), total dissolved solids (TDS), conductivity, pH, temperature, ammonia nitrogen, nitrate nitrogen, iron, copper, phosphate, potassium, sulfate, turbidity, zinc and bacterial levels was performed following standard test protocols as presented in Standard Methods for the Examination of Water and Wastewater [9]. Results of the comparisons of the various surface water streams showed that phosphate levels, according to Mitchell and Stapp, were considered good for Lake Claiborne (control) and Bayou Dorcheat. The levels were found to be .001 mg/L and .007 mg/L respectively. Other streams associated with animal waste, had higher phosphate levels of 2.07 mg/L and 2.78 mg/L, respectively. Conductivity and total dissolved solids (TDS) levels were the lowest in Lake Claiborne and highest in the Hill Farm Research Station stream. It can be concluded from the data that some bacterial levels and various nutrient levels can be affected in water resources due to non-point source pollution. Many of these levels will remain unaffected.

Development of a Field Laundry Wastewater Recycling System

Science.gov (United States)

1986-04-01

its physical , chemical, and toxicological properties . Chemical interactions may also occur in laundry water that may result in additional compounds of...was used to prepare a diatomite slurry needed to precoat the septums in the diatomaceous earth filter. II 6 If Sx COLLECTION TANK (CT) Figure 3...biochemical oxygen demand (BOD) bottles were then taken. The samples were divided into fractions for replicate testing of chemical and physical

Water Quality Characteristics of Sembrong Dam Reservoir, Johor, Malaysia

Science.gov (United States)

Mohd-Asharuddin, S.; Zayadi, N.; Rasit, W.; Othman, N.

2016-07-01

A study of water quality and heavy metal content in Sembrong Dam water was conducted from April - August 2015. A total of 12 water quality parameters and 6 heavy metals were measured and classified based on the Interim National Water Quality Standard of Malaysia (INWQS). The measured and analyzed parameter variables were divided into three main categories which include physical, chemical and heavy metal contents. Physical and chemical parameter variables were temperature, dissolved oxygen (DO), biochemical oxygen demand (BOD), chemical oxygen demand (COD), total suspended solid (TSS), turbidity, pH, nitrate, phosphate, ammonium, conductivity and salinity. The heavy metals measured were copper (Cu), lead (Pb), aluminium (Al), chromium (Cr), ferum (Fe) and zinc (Zn). According to INWQS, the water salinity, conductivity, BOD, TSS and nitrate level fall under Class I, while the Ph, DO and turbidity lie under Class IIA. Furthermore, values of COD and ammonium were classified under Class III. The result also indicates that the Sembrong Dam water are not polluted with heavy metals since all heavy metal readings recorded were falls far below Class I.

Study of the degradation performance (TOC, BOD, and toxicity) of bisphenol A by the photo-Fenton process.

Science.gov (United States)

Pérez-Moya, M; Kaisto, T; Navarro, M; Del Valle, L J

2017-03-01

Degradation of bisphenol A (BPA, 0.5 L, 30 mg L -1 ) was studied by photo-Fenton treatment, while Fenton reagents were variables. The efficiency of the degradation process was evaluated by the reduction of total organic carbon (TOC), the biochemical oxygen demand (BOD), and toxicity. For toxicity analysis, bacterial methods were found infeasible, but the in vitro assay of VERO cells culture was successfully applied. Experiments according to a 2 2 design of experiments (DOE) with star points and three center points for statistical validity allowed selecting those process conditions (Fe(II) and H 2 O 2 load) that maximized the process performance. Photo-Fenton process effectively eliminated BPA and partly degraded its by-products (residual TOC TOC = 92 %) was attained. Toxicity was also detected to 50 % of cellular mortality even at long reaction times. However, 40.25 mg L -1 of H 2 O 2 decreased residual TOC to 70 % while cell mortality decreased down to 25 %. With more H 2 O 2 , the residual TOC decreased down to 15 % but cell mortality remained within the 20-25 % level. Photo-Fenton increased the biodegradability and reduced the toxicity of the studied sample.

Flame-Oxidized Stainless-Steel Anode as a Probe in Bioelectrochemical System-Based Biosensors to Monitor the Biochemical Oxygen Demand of Wastewater

Directory of Open Access Journals (Sweden)

Qiaochu Liang

2018-02-01

Full Text Available Biochemical oxygen demand (BOD is a widely used index of water quality in wastewater treatment; however, conventional measurement methods are time-consuming. In this study, we analyzed a novel flame-oxidized stainless steel anode (FO-SSA for use as the probe of bioelectrochemical system (BES-based biosensors to monitor the BOD of treated swine wastewater. A thinner biofilm formed on the FO-SSA compared with that on a common carbon-cloth anode (CCA. The FO-SSA was superior to the CCA in terms of rapid sensing; the response time of the FO-SSA to obtain the value of R2 > 0.8 was 1 h, whereas the CCA required 4 h. These results indicate that the FO-SSA offers better performance than traditional CCAs in BES biosensors and can be used to improve biomonitoring of wastewater.

Determination of Biological Treatability Processes of Textile Wastewater and Implementation of a Fuzzy Logic Model

Directory of Open Access Journals (Sweden)

Harun Akif Kabuk

2015-01-01

Full Text Available This study investigated the biological treatability of textile wastewater. For this purpose, a membrane bioreactor (MBR was utilized for biological treatment after the ozonation process. Due to the refractory organic contents of textile wastewater that has a low biodegradability capacity, ozonation was implemented as an advanced oxidation process prior to the MBR system to increase the biodegradability of the wastewater. Textile wastewater, oxidized by ozonation, was fed to the MBR at different hydraulic retention times (HRT. During the process, color, chemical oxygen demand (COD, and biochemical oxygen demand (BOD removal efficiencies were monitored for 24-hour, 12-hour, 6-hour, and 3-hour retention times. Under these conditions, 94% color, 65% COD, and 55% BOD removal efficiencies were obtained in the MBR system. The experimental outputs were modeled with multiple linear regressions (MLR and fuzzy logic. MLR results suggested that color removal is more related to COD removal relative to BOD removal. A surface map of this issue was prepared with a fuzzy logic model. Furthermore, fuzzy logic was employed to the whole modeling of the biological system treatment. Determination coefficients for COD, BOD, and color removal efficiencies were 0.96, 0.97, and 0.92, respectively.

Phytoremediation Potential of Vetiver System Technology for Improving the Quality of Palm Oil Mill Effluent

Directory of Open Access Journals (Sweden)

Negisa Darajeh

2014-01-01

Full Text Available Palm oil mill effluent (POME, a pollutant produced by the palm oil industry, was treated by the Vetiver system technology (VST. This technology was applied for the first time to treat POME in order to decrease biochemical oxygen demand (BOD and chemical oxygen demand (COD. In this study, two different concentrations of POME (low and high were treated with Vetiver plants for 2 weeks. The results showed that Vetiver was able to reduce the BOD up to 90% in low concentration POME and 60% in high concentration POME, while control sets (without plant only was able to reduce 15% of BOD. The COD reduction was 94% in low concentration POME and 39% in high concentration POME, while control just shows reduction of 12%. Morphologically, maximum root and shoot lengths were 70 cm, the number of tillers and leaves was 344 and 86, and biomass production was 4.1 kg m−2. These results showed that VST was effective in reducing BOD and COD in POME. The treatment in low concentration was superior to the high concentration. Furthermore, biomass of plant can be considered as a promising raw material for biofuel production while high amount of biomass was generated in low concentration of POME.

Online total organic carbon (TOC) monitoring for water and wastewater treatment plants processes and operations optimization

Science.gov (United States)

Assmann, Céline; Scott, Amanda; Biller, Dondra

2017-08-01

Organic measurements, such as biological oxygen demand (BOD) and chemical oxygen demand (COD) were developed decades ago in order to measure organics in water. Today, these time-consuming measurements are still used as parameters to check the water treatment quality; however, the time required to generate a result, ranging from hours to days, does not allow COD or BOD to be useful process control parameters - see (1) Standard Method 5210 B; 5-day BOD Test, 1997, and (2) ASTM D1252; COD Test, 2012. Online organic carbon monitoring allows for effective process control because results are generated every few minutes. Though it does not replace BOD or COD measurements still required for compliance reporting, it allows for smart, data-driven and rapid decision-making to improve process control and optimization or meet compliances. Thanks to the smart interpretation of generated data and the capability to now take real-time actions, municipal drinking water and wastewater treatment facility operators can positively impact their OPEX (operational expenditure) efficiencies and their capabilities to meet regulatory requirements. This paper describes how three municipal wastewater and drinking water plants gained process insights, and determined optimization opportunities thanks to the implementation of online total organic carbon (TOC) monitoring.

[Comparison of ciliate diversity in biodisc reactors which purify industrial wastewater].

Science.gov (United States)

Luna-Pabello, V M; Durán De Bazúa, C; Aladro-Lubel, M A

1995-01-01

The comparative study of the ciliate populations present in rotating biological reactors (biodiscs reactors) of 20 l working volume, treating three different wastewaters is the aim of this project. Wastewaters chosen were those of a maize mill, of a sugarcane/ethyl alcohol plant, and of a recycled paper mill. Its dissolved organic contents, measured as soluble chemical oxygen demand (COD) and five-day biochemical oxygen demand (BOD5), were 2040 mg COD/l and 585 mg BOD5/l for maize mill effluents (nejayote), 2000 mg COD/l and 640 mg BOD5/l for sugarcane/ethanol effluents (vinasses), and 960 mg COD/l and 120 mg BOD5/l for whitewaters of the paper industry. Results obtained indicate that ciliate proliferate in all chambers of reactors treating these wastewaters. The ciliates were more abundant in vinasses, followed by nejayote, and then whitewaters. Among protozoa, ciliates were present as follows: 19 species in total. Three of them were common for the three systems. Free swimming ciliates were in higher proportion than pedunculated ones. Its diversity was higher for the whitewaters system, next for nejayote, and the lesser, for vinasses, corroborating the fact that less polluted waters have higher organisms' diversity.

Application of Electrocoagulation Process for Dairy Wastewater Treatment

Directory of Open Access Journals (Sweden)

Edris Bazrafshan

2013-01-01

Full Text Available Dairy industry wastewater is characterized by high biochemical oxygen demand (BOD5, chemical oxygen demand (COD, and other pollution load. The purpose of this study was to investigate the effects of the operating parameters such as applied voltage, number of electrodes, and reaction time on a real dairy wastewater in the electrocoagulation process. For this purpose, aluminum electrodes were used in the presence of potassium chloride as electrolytes. It has been shown that the removal efficiency of COD, BOD5, and TSS increased with increasing the applied voltage and the reaction time. The results indicate that electrocoagulation is efficient and able to achieve 98.84% COD removal, 97.95% BOD5 removal, 97.75% TSS removal, and >99.9% bacterial indicators at 60 V during 60 min. The experiments demonstrated the effectiveness of electrocoagulation techniques for the treatment of dairy wastewaters. Finally, the results demonstrated the technical feasibility of electrocoagulation process using aluminum electrodes as a reliable technique for removal of pollutants from dairy wastewaters.

THE USE OF SILICA SAND, ZEOLITE AND ACTIVE CHARCOAL TO REDUCE BOD, COD AND TSS OF LAUNDRY WASTE WATER AS A BIOLOGY LEARNING RESOURCES

Directory of Open Access Journals (Sweden)

Moch Assiddieq

2017-11-01

Full Text Available The aquatic environment contaminated with detergent waste in high concentrations can endanger the lives human and biota in the water. This study aimed to determine the decrease of BOD, COD and TSS content of laundry liquid waste by using filter media of silica sand, zeolite, and activated charcoal. Filter medium 1a can reduce BOD level from 98.6 mg/L to 58.80 mg/L (40.36%, while medium 1b can decrease BOD level to 21.20 mg/L (78.48%. It showed that media 1a had not fulfilled the quality standard of BOD of waste water that is 50 mg/L, while media 1b had fulfilled the standard of quality. Filter media 1a can decrease COD level from 210 mg/L to 78.80 mg/L (62.47%, whereas medium 1b can decrease COD to 25.60 mg/L (87.80%. This showed that media 1a and media 1b had met the quality standard of COD of waste water that is 100 mg/L. Filter media 1a can decrease TSS level from 465 mg/L to 122.5 mg/L (73.65%, whereas medium 1b can decrease TSS level to 52.3 mg/L (88.75%. This showed that media 1a and media 1b had met the quality standard of TSS of waste water that is 150 mg/L.

Treatment of municipal wastewater in full-scale on-site sand filter reduces BOD efficiently but does not reach requirements for nitrogen and phosphorus removal.

Science.gov (United States)

Laaksonen, Petteri; Sinkkonen, Aki; Zaitsev, Gennadi; Mäkinen, Esa; Grönroos, Timo; Romantschuk, Martin

2017-04-01

A traditional sand filter for treatment of household wastewater was constructed in the fall of 2012 at Biolinja 12, Turku, Finland. Construction work was led and monitored by an authorized wastewater treatment consultant. The filter was placed on a field bordered by open ditches from all sides in order to collect excess rain and snowmelt waters. The filter was constructed and insulated from the environment so that all outflowing water was accounted for. Untreated, mainly municipal, wastewater from Varissuo suburb was pumped from a sewer separately via three septic tanks (volume = 1 m 3 each) into the filters. Normally, wastewater was distributed to ground filters automatically according to pre-programmed schedule. Initially, the daily flow was 1200 L day -1 to reflect the average organic load of a household of five persons (load: ca 237 g day -1 BOD; 73 g day -1 total N; and 10.4 g day -1 total P). Later in the test, the flow rate was decreased first to 900 and then to 600 L day -1 to better reflect the average volume produced by five persons. Volumes of inlet wastewater as well as treated water were monitored by magnetic flow meters. Samples were withdrawn from the inlet water, from the water entering the filters after the third septic tank, and from the outflowing water. After an initial adaption time, the reductions in BOD and chemical oxygen demand were constantly between 92 and 98%, showing that the biological degradation process in the filters functioned optimally and clearly comply with the national and EU standards. The reduction in total nitrogen and total phosphorus, however, reached required levels only during the first months of testing, apparently when buildup of microbial biomass was still ongoing. After this initial period of 3 months showing satisfactory reduction levels, the reduction of total nitrogen varied between 5 and 25% and total phosphorus mostly between 50 and 65%. Nitrification was efficient in the filter, but as indicated

Oxidant reduction and biodegradability improvement of paper mill effluent by irradiation

International Nuclear Information System (INIS)

Tiezheng Wang; Waite, T.D.; Kurucz, C.

1994-01-01

Paper mill bleach processing wastewaters represent a large input of hazardous compounds to the environment and these compounds are usually non-biodegradable. A preliminary study using a 5000 Ci 60 Co gamma radiation source as a surrogate for electron beam irradiation, potentially an emerging technology for wastewater treatment, to treat a paper mill bleach effluent showed that for an absorbed dose of 800 krads, chemical oxygen demand (COD) was reduced by 13.5% and 5 day biochemical oxygen demand (BOD 5 ) was increased 58.6%. These changes altered the value of COD/BOD 5 from 14 to 5. For the same dose, the absorbable organic halogen (AOX) was reduced 76.2%. These results suggested the possibility of using the electron beam process to detoxify paper mill effluent thereby generating a more biodegradable wastewater. (author)

Análise da demanda por defensivos pela fruticultura brasileira 1997-2000 Fruit tree demand for chemicals 1997-2000

Directory of Open Access Journals (Sweden)

Evaristo Marzabal Neves

2002-12-01

Full Text Available Este estudo estima a demanda relativa por defensivos pela fruticultura brasileira, principalmente para banana, laranja, maçã, melão e uva, por dispêndio total e volume de princípio ativo por hectare, para o período de 1997 a 2000. Efetua, também, uma análise comparativa destas demandas com as obtidas para as principais culturas brasileiras (soja, milho, cana-de-açúcar e café, as quais são predominantes em termos de área cultivada e dominantes, em termos absolutos, nos dispêndios totais e volumes demandados por princípio ativo em defensivos no Brasil. Determina, ainda, em termos absolutos, a participação da fruticultura nos dispêndios totais e no consumo de princípio ativo, especialmente em acaricidas e fungicidas. Conclui sobre a importância da estimativa da demanda relativa para a fruticultura, que supera significativamente as principais culturas comerciais do País, fornecendo indicadores para o comportamento de mercado para as diferentes classes de defensivos pela fruticultura brasileira.This study estimates for the Brazilian fruit trees, mainly banana, orange, apple, melon and grape, the relative demand for chemicals, considering total expenses and quantity demanded for active principle per hectare, from 1997 to 2000. It is also established a comparative analysis among this demand with ones made by the main Brazilian crops (soybean, maize, sugar cane and coffee, that are predominating in terms of grown area and dominating, in absolute terms, of chemicals total expenses and consume of active principle volume in Brazil. Yet, determines, in absolute terms, the importance of fruit trees in chemicals total expenses and active principle consume, especially acaricides and fungicides. It concludes, about the importance of estimated relative demand for fruit trees, that it is higher than the ones by the mainly commercial crops in the country, offering indicators for the demand and market behavior to chemicals different classes by

Artificial neural network modelling of biological oxygen demand in rivers at the national level with input selection based on Monte Carlo simulations.

Science.gov (United States)

Šiljić, Aleksandra; Antanasijević, Davor; Perić-Grujić, Aleksandra; Ristić, Mirjana; Pocajt, Viktor

2015-03-01

Biological oxygen demand (BOD) is the most significant water quality parameter and indicates water pollution with respect to the present biodegradable organic matter content. European countries are therefore obliged to report annual BOD values to Eurostat; however, BOD data at the national level is only available for 28 of 35 listed European countries for the period prior to 2008, among which 46% of data is missing. This paper describes the development of an artificial neural network model for the forecasting of annual BOD values at the national level, using widely available sustainability and economical/industrial parameters as inputs. The initial general regression neural network (GRNN) model was trained, validated and tested utilizing 20 inputs. The number of inputs was reduced to 15 using the Monte Carlo simulation technique as the input selection method. The best results were achieved with the GRNN model utilizing 25% less inputs than the initial model and a comparison with a multiple linear regression model trained and tested using the same input variables using multiple statistical performance indicators confirmed the advantage of the GRNN model. Sensitivity analysis has shown that inputs with the greatest effect on the GRNN model were (in descending order) precipitation, rural population with access to improved water sources, treatment capacity of wastewater treatment plants (urban) and treatment of municipal waste, with the last two having an equal effect. Finally, it was concluded that the developed GRNN model can be useful as a tool to support the decision-making process on sustainable development at a regional, national and international level.

The viability of biological treatment at Ibi wastewater treatment station; Viabilidad del tratamiento biologico de aguas residuales

Energy Technology Data Exchange (ETDEWEB)

Flor Garcia, M.V.; Morenilla Martinez, J.J.; Ruiz Zapata, R.

1996-06-01

In this study, we have proved the viability of biological treatment of leaving waters from Ibi Wastewater Treatment Station, where water is subject to the action of coagulant agents, following a physical and chemical process. the experience was based on wastewater treatment by using activated sludge, at experimental scale in a pilot plant. During the experiments, we controlled the main parameters which indicate treatment success; namely, Suspended Solids (SS), pH, Biochemical Oxygen Demand (BOD) and Chemical Oxygen Demand (COD), in addition to other substances such as nutrients and toxicants, and inhibitors of bio metabolism. (Author) 6 refs.

Miniaturized and green method for determination of chemical oxygen demand using UV-induced oxidation with hydrogen peroxide and single drop microextraction

International Nuclear Information System (INIS)

Akhoundzadeh, Jeyran; Chamsaz, Mahmoud; Costas, Marta; Lavilla, Isela; Bendicho, Carlos

2013-01-01

We report on a green method for the determination of low levels of chemical oxygen demand. It is based on the combination of (a) UV-induced oxidation with hydrogen peroxide, (b) headspace single-drop microextraction with in-drop precipitation, and (c) micro-turbidimetry. The generation of CO 2 after photolytic oxidation followed by its sequestration onto a microdrop of barium hydroxide gives rise to a precipitate of barium carbonate which is quantified by turbidimetry. UV-light induced oxidation was studied in the absence and presence of H 2 O 2 , ultrasound, and ferrous ion. Determinations of chemical oxygen demand were performed using potassium hydrogen phthalate as a model compound. The optimized method gives a calibration curve that is linear between 3.4 and 20 mg L −1 oxygen. The detection limit was 1.2 mg L −1 of oxygen, and the repeatability (as relative standard deviation) was around 5 %. The method was successfully applied to the determination of chemical oxygen demand in different natural waters and a synthetic wastewater. (author)

Variation of physico-chemical characteristics with tide in Visakhapatnam harbour waters, east coast of India

Digital Repository Service at National Institute of Oceanography (India)

RamaRaju, V.S.; Rao, T.V.N.; Rathod, V.

Variations in physico-chemical parameters (DO, BOD, NO2, SiO4, PO4 suspended solids, salinity and currents) observed in the waters of main channel of Visakhapatnam Harbour over a tidal cycle in different seasons from February 1982 to January 1983...

Preliminary Study on Treatment of Palm Oil Mill Effluent (POME by Sand Filtration-DBD Plasma System

Directory of Open Access Journals (Sweden)

Ariadi Hazmi

2016-02-01

Full Text Available In the palm oil industry, open ponding, aerobic and anaerobic digestion, physicochemical treatment and membrane filtration are generally applied as conventional treatments of palm oil mill effluent (POME. In this study, a sand filtration-dielectric barrier discharge (DBD system was investigated as an alternative process for treating POME. This system can reduce land usage, processing time and costs compared to conventional systems. The removal efficiency of chemical oxygen demand (COD, biological oxygen demand (BOD5, and oil-grease in relation to the applied voltage were studied. Furthermore, the pH and temperature profiles were investigated. The obtained results indicate that the removal efficiency of COD, BOD5, and oil-grease increased with an increase of the applied voltage. The electrical energy consumption needed is about 10.56 kWh/L of POME.

Pharmaceutical wastewater treatment: a physicochemical study

International Nuclear Information System (INIS)

Saleem, M.

2007-01-01

A physicochemical study for the treatment of pharmaceutical wastewater was performed. Objective of the laboratory investigation was to study the removal of color, Total Dissolved Solids (TDS), Biochemical Oxygen Demand (BOD), Chemical Oxygen Demand (COD), turbidity and phenol and bring them up to the allowable limits for reuse purposes. Efficiency of coagulation, flocculation, sedimentation, sand filtration followed by activated carbon adsorption was determined. It was found that tested coagulants (alum, ferric chloride, and ferrous sulphate) are not much effective and required high dosage for the removal; of TSS, BOD, COD and turbidity. Alum was found to be more effective among tested coagulants and reduce TSS, BOD, COD and turbidity 79.6%, 34.8, 48.6% and 69.2% respectively. Sand filtration further reduced the studied parameters 97.7%, 95.7%, 93.9% and 76.9% respectively. As the concentration of phenol in the studied pharmaceutical wastewater was 100 mg/l, granular activated carbon was used to remove phenol up to the allowable limit for reuse purpose. Activated carbon adsorption further reduces phenol, TDS, TSS, BOD, and COD up to 99.9%, 99.1%, 21.4%, 81.3% and 71.1% respectively. High removal of color observed after activated carbon adsorption. It was concluded that the suggested treatment scheme is suitable to bring the effluent quality up to the water quality standards. (author)

Eletrólise de resíduos poluidores: I - Efluente de uma indústria liofilizadora de condimentos Electrolysis of polluting wastes: I - Wastewater from a seasoning freeze-drying industry

Directory of Open Access Journals (Sweden)

Dejanira F. de Angelis

1998-02-01

Full Text Available Wastewater from a seasoning freeze-drying industry was electrolysed to increase its biodegradability. Stainless-steel electrodes were used at 9.09 A/m², for up to 80 min. Conductivity, pH, biochemical (BOD and chemical (COD oxygen demands, Daphnia similis acute toxicity bioassays, and bacteria counting through the plate count agar method were determined after different times of electrolysis. The results (e.g. higher BOD and lower COD showed that the biodegradability of the wastewater was significantly increased; furthermore, Fe2+ ions liberated by the electrodes cause microorganisms to die and, when oxidised to Fe3+, contribute for the flocculation and sedimentation of solid residues.

Economic Value Approach to Industrial Water Demand Management, A Case Study of Chemical Plants

Directory of Open Access Journals (Sweden)

morteza tahami pour zarandi

2017-03-01

Full Text Available Limitations in water supply to meet the increasing demand have encouraged both planners and researchers to focus attention on water demand management, in which such economic tools as the water pricing system play a major role. A fundamental component of the pricing system is the estimation of the economic value of water, which reflects a firm’s maximum affordable water price or the ultimate elasticity of industrial water. The present study was conducted to estimate the economic value of water for basic chemical plants, excluding fertilizers and nitrogen compounds (code 2411, representing the four-digit ISIC industrial codes which account for about 14% of the total industrial water consumption. The econometric method of production function within the framework of panel data and the residual method were used. Data were collected from the Census of medium-sized businesses carried out by the Statistical Center of Iran over the period 1997–2013.  Results showed that one cubic meter of water allocated to the plants surveyed creates a value of 3,7071 Rials, which shows a large gap with the current purchase price of 5685 Rials. Moreover, it was found that the present water prices account for only about 1.3 percent of the total production cost of basic chemicals, excluding fertilizers and nitrogen compounds. It may, thus, be concluded that it is reasonable to increase the present water tariffs and discriminate among the various manufacturing codes by differences in tariffs in order to achieve water demand management goals. Finally, the information emerging from the study may be exploited to improve the revenues earned by water authorities or to carry out feasibility studies of industrial water development projects.

Physical-chemical and operational performance of an anaerobic baffled reactor (ABR treating swine wastewater - 10.4025/actascitechnol.v32i4.7203

Directory of Open Access Journals (Sweden)

Erlon Lopes Pereira

2010-12-01

Full Text Available Since hog raising concentrates a huge amount of swine manure in small areas, it is considered by the environmental government organizations to be one of the most potentially pollutant activities. Therefore the main objective of this research was to evaluate by operational criteria and removal efficiency, the performance of a Anaerobic Baffled Reactor (ABR, working as a biological pre-treatment of swine culture effluents. The physical-chemical analyses carried out were: total COD, BOD5, total solids (TS, fix (TFS and volatiles (TVS, temperature, pH, total Kjeldahl nitrogen, phosphorus, total acidity and alkalinity. The ABR unit worked with an average efficiency of 65.2 and 76.2%, respectively, concerning total COD and BOD5, with a hydraulic retention time (HRT about 15 hours. The results for volumetric organic loading rate (VOLR, organic loading rate (OLR and hydraulic loading rate (HLR were: 4.46 kg BOD m-3 day-1; 1.81 kg BOD5 kg TVS-1 day-1 and 1.57 m3 m-3 day-1, respectively. The average efficiency of the whole treatment system for total COD and BOD5 removal were 66.5 and 77.8%, showing an adequate performance in removing the organic matter from swine wastewater.

Hydraulic Behavior and Chemical Characterization of Lapilli as Material for Natural Filtering of Slurry

Directory of Open Access Journals (Sweden)

Nereida Falcón-Cardona

2015-06-01

Full Text Available Livestock effluents are a beneficial nutrient supply for crops, whereby their use is critical to ensure the sustainability of the farms global management. However, they can cause serious ecological problems if misused, polluting soils and groundwater. Combining “soft technology” and local materials is a low cost solution in terms of finance and energy. The REAGUA project (REuso AGUA, Water reuse in Spanish analyzes the possibility of using “picon” (lapilli as a material for the treatment of liquid manure from ruminants, for later use in subsurface drip irrigation system to produce forage and biofuels, in which the soil acts as a subsequent advanced treatment. A three-phase system, in which the effluent was poured with a vertical subsurface flow in an unsaturated medium, is designed. In order to determine the management conditions that optimize the filter, it was necessary to characterize the hydraulic behavior of lapilli and its ability to remove substances. Using three lapilli-filled columns, unsaturated flux, and a ruminant effluent, the reduction of chemical oxygen demand (COD, biochemical oxygen demand after 5 days (BOD5 and ammonia, phosphorus and suspension solids (SS obtained was over 80%, 90%, and 95% respectively, assumable values for irrigation.

Treatment of amoxicillin by O3/Fenton process in a rotating packed bed.

Science.gov (United States)

Li, Mo; Zeng, Zequan; Li, Yingwen; Arowo, Moses; Chen, Jianfeng; Meng, Hong; Shao, Lei

2015-03-01

In this study, simulated amoxicillin wastewater was treated by the O3/Fenton process in a rotating packed bed (RPB) and the results were compared with the Fenton process and the O3 followed by Fenton (O3 + Fenton) process. The chemical oxygen demand (COD) removal rate and the ratio of 5-day biological oxygen demand to chemical oxygen demand (BOD5/COD) in the O3/Fenton process were approximately 17% and 26%, respectively, higher than those in the O3 + Fenton process with an initial pH of 3. The COD removal rate of the amoxicillin solution reached maximum at the Fe(II) concentration of 0.6 mM, temperature of 25 °C, rotation speed of 800 rpm and initial pH of 3. The BOD5/COD of the amoxicillin solution increased from 0 to 0.38 after the solution was treated by the O3/Fenton process. Analysis of the intermediates indicated that the pathway of amoxicillin degradation in the O3/Fenton process was similar to that in the O3 + Fenton process. Contrast experiment results showed that amoxicillin degradation was significantly intensified in the RPB. Copyright © 2014 Elsevier Ltd. All rights reserved.

THE EFFECT OF INFLUENT CONCENTRATION AND HYDRAULIC LOADING RATE (HLR TO BOD AND COD REMOVAL ON ARTIFICIAL DOMESTIC WASTEWATER TREATMENT (GREY WATER USING UASB REACTOR

Directory of Open Access Journals (Sweden)

Syafrudin Syafrudin

2014-05-01

Full Text Available Upflow anaerobic sludge blanket (UASB reactor is one of anaerobic biological treatment was develop in late 1970’s. UASB reactor is suitable for the tropic areas because it has a high temperature about 20°-30°C. Domestic wastewater is divided into two types, namely black water and grey water. But in this case used domestic grey water. Grey water is household wastewater from showers, sinks and kitchen. Grey water has a total 75% of the domestic wastewater volume. The research was conducted in laboratory scale. This study performed a variation of Hydraulic Loading Rate (HLR and the influent concentration. There were 25 reactors include 5 variations of influent concentration and 5 Hydraulic Loading Rate’s (HLR variation. The research could asses BOD5 and COD removal with treatment in UASB. Efficiency of BOD5 removal by varying the influent concentration and HLR was about 38%-75% and COD was about 40%-77%. The lower concentration could be increase efficiency BOD5 and COD removal. Influent concentration optimum occurred when middle concentration was about 840 mg/L COD and HLR optimum was 0,05 m3/m2/hour.

Lipid production from tapioca wastewater by culture of Scenedesmus sp. with simultaneous BOD, COD and nitrogen removal

Science.gov (United States)

Romaidi; Hasanudin, Muhammad; Kholifah, Khusnul; Maulidiyah, Alik; Putro, Sapto P.; Kikuchi, Akira; Sakaguchi, Toshifumi

2018-05-01

The use of microalgae to produce biodiesel or possibly remove nutrients from industrial wastewater has gained important attention during recent years due to their photosynthetic rate and its versatile nature to grow in various wastewater systems. In this study, a microalgae, Scenedesmus sp., was cultured to enhance the lipid production and nutrients removal from tapioca wastewater sample. To assess lipid production, Scenedesmus sp. was cultured in different concentration of tapioca wastewater sample (from 0 to 100 %), and nutrient removal including BOD, COD, NH4, NO2, NO3 level by Scenedesmus sp. was assessed in 100% of tapioca wastewater culture. After 8 days of culture, it was found out that 50% of tapioca wastewater sample resulted in highest concentration of lipid content than that of the other concentrations. The level of environment indicator as nutrient removal such as BOD, COD, NH4, NO2, NO3 were also decreased up to 74%, 72%, 95%, 91%, and 91%, respectively. The pH condition changed from initial condition acidic (pH: 4) to neutral or basic condition (pH: 7-8) as recommended in wastewater treatment system. This research provided a novel approach and achieved efficient simultaneous lipid production and nutrients removal from tapioca wastewater sample by Scenedesmus’s culture system.

Ọmọ̀jọ́lá, Bodé. Yorùbá Music in the Twentieth Century: Identity, Agency and Performance Practice

OpenAIRE

Vallier, Gilles-Félix

2017-01-01

Ọmọ̀jọ́lá, Bodé. — Yorùbá Music in the Twentieth Century : Identity, Agency and Performance Practice. New York, University of Rochester Press ; Eastman, Rochester Studies in Ethnomusicology, 2012, 285 p., bibl., ill., CD. Yorùbá Music in the Twentieth Century de Bodé Ọmọ̀jọ́lá déconstruit efficacement la notion d'une culture musicale yorùbá singulière, découvrant à la place une tapisserie pittoresque de traditions socialement et esthétiquement diverses, lesquelles sont unies, dans bien des ...

Modelling soil dust aerosol in the Bodélé depression during the BoDEx campaign

OpenAIRE

Tegen , I.; Heinold , B.; Todd , M.; Helmert , J.; Washington , R.; Dubovik , O.

2006-01-01

International audience; We present regional model simulations of the dust emission events during the Bodélé Dust Experiment (BoDEx) that was carried out in February and March 2005 in Chad. A box model version of the dust emission model is used to test different input parameters for the emission model, and to compare the dust emissions computed with observed wind speeds to those calculated with wind speeds from the regional model simulation. While field observations indicate that dust producti...

Modelling soil dust aerosol in the Bodélé depression during the BoDEx campaign

OpenAIRE

R. Washington; J. Helmert; M. Todd; B. Heinold; I. Tegen; O. Dubovik

2006-01-01

We present regional model simulations of the dust emission events during the Bodélé Dust Experiment (BoDEx) that was carried out in February and March 2005 in Chad. A box model version of the dust emission model is used to test different input parameters for the emission model, and to compare the dust emissions computed with observed wind speeds to those calculated with wind speeds from the regional model simulation. While field observations indicate that dust production occurs via ...

Characterization of chromophoric dissolved organic matter and relationships among PARAFAC components and water quality parameters in Heilongjiang, China.

Science.gov (United States)

Cui, Hongyang; Shi, Jianhong; Qiu, Linlin; Zhao, Yue; Wei, Zimin; Wang, Xinglei; Jia, Liming; Li, Jiming

2016-05-01

Chromophoric dissolved organic matter (CDOM) is an important optically active substance that can transports nutrients and pollutants from terrestrial to aquatic systems. Additionally, it is used as a measure of water quality. To investigate the source and composition of CDOM, we used chemical and fluorescent analyses to characterize CDOM in Heilongjiang. The composition of CDOM can be investigated by excitation-emission matrix (EEM) fluorescence and parallel factor analysis (PARAFAC). PARAFAC identified four individual components that were attributed to microbial humic-like (C1) and terrestrial humic-like (C2-4) in water samples collected from the Heilongjiang River. The relationships between the maximum fluorescence intensities of the four PARAFAC components and the water quality parameters indicate that the dynamic of the four components is related to nutrients in the Heilongjiang River. The relationships between the fluorescence component C3 and the biochemical oxygen demand (BOD5) indicates that component C3 makes a great contribution to BOD5 and it can be used as a carbon source for microbes in the Heilongjiang River. Furthermore, the relationships between component C3, the particulate organic carbon (POC), and the chemical oxygen demand (CODMn) show that component C3 and POC make great contributions to BOD5 and CODMn. The use of these indexes along with PARAFAC results would be of help to characterize the co-variation between the CDOM and water quality parameters in the Heilongjiang River.

Manual or automated measuring of antipsychotics' chemical oxygen demand.

Science.gov (United States)

Pereira, Sarah A P; Costa, Susana P F; Cunha, Edite; Passos, Marieta L C; Araújo, André R S T; Saraiva, M Lúcia M F S

2018-05-15

Antipsychotic (AP) drugs are becoming accumulated in terrestrial and aqueous resources due to their actual consumption. Thus, the search of methods for assessing the contamination load of these drugs is mandatory. The COD is a key parameter used for monitoring water quality upon the assessment of the effect of polluting agents on the oxygen level. Thus, the present work aims to assess the chemical oxygen demand (COD) levels of several typical and atypical antipsychotic drugs in order to obtain structure-activity relationships. It was implemented the titrimetric method with potassium dichromate as oxidant and a digestion step of 2h, followed by the measurement of remained unreduced dichromate by titration. After that, an automated sequential injection analysis (SIA) method was, also, used aiming to overcome some drawbacks of the titrimetric method. The results obtained showed a relationship between the chemical structures of antipsychotic drugs and their COD values, where the presence of aromatic rings and oxidable groups give higher COD values. It was obtained a good compliance between the results of the reference batch procedure and the SIA system, and the APs were clustered in two groups, with the values ratio between the methodologies, of 2 or 4, in the case of lower or higher COD values, respectively. The SIA methodology is capable of operating as a screening method, in any stage of a synthetic process, being also more environmentally friendly, and cost-effective. Besides, the studies presented open promising perspectives for the improvement of the effectiveness of pharmaceutical removal from the waste effluents, by assessing COD values. Copyright © 2018 Elsevier Inc. All rights reserved.

Onsite Greywater Treatment using Pilot Scale Technology

Directory of Open Access Journals (Sweden)

Manzoor-ul-Haq Rajput

2015-04-01

Full Text Available The GROW Technology for greywater treatment was installed at the MUET (Mehran University of Engineering & Technology, hostel and run under continuous flow conditions with hydraulic loading rate of 0.15m.d-1. The monitoring and analysis of influent and effluent water were carried out during January-December, 2010. Local plants species such as water hyacinth, Pennywort (duck weed, Mint and Cattail were used in the GROW rig as a mixed mode. Coarse Gravels were filled in the troughs as a medium. The collected samples were analyzed for BOD5 (Biochemical Oxygen Demand, COD (Chemical Oxygen Demand, TSS (Total Suspended Solids, pH, and DO (Dissolved Oxygen. Removal efficiencies of BOD5, COD and TSS were calculated as 83.0,69.0 and 84.0% respectively. DO was found increased from 0.6-3.5 mg.dm-3 while pH was observed between 6.5-7.8

Onsite greywater treatment using pilot scale grow technology

International Nuclear Information System (INIS)

Rajput, M.U.

2015-01-01

The GROW Technology for greywater treatment was installed at the MUET (Mehran University of Engineering and Technology), hostel and run under continuous flow conditions with hydraulic loading rate of 0.15m.d-1. The monitoring and analysis of influent and effluent water were carried out during January-December, 2010. Local plants species such as water hyacinth, Pennywort (duck weed), Mint and Cattail were used in the GROW rig as a mixed mode. Coarse Gravels were filled in the troughs as a medium. The collected samples were analyzed for BOD5 (Biochemical Oxygen Demand), COD (Chemical Oxygen Demand), TSS (Total Suspended Solids), pH, and DO (Dissolved Oxygen). Removal efficiencies of BOD5, COD and TSS were calculated as 83.0,69.0 and 84.0% respectively. DO was found increased from 0.6-3.5 mg.dm-3 while pH was observed between 6.5-7.8. (author)

Determination of chemical oxygen demand (COD) using an alternative wet chemical method free of mercury and dichromate.

Science.gov (United States)

Kolb, Marit; Bahadir, Müfit; Teichgräber, Burkhard

2017-10-01

Worldwide, the standard methods for the determination of the important wastewater parameter chemical oxygen demand (COD) are still based on the use of the hazardous chemicals, mercury sulfate and chromium(VI). However, due to their properties they are meanwhile classified as "priority pollutants" and shall be phased out or banned in the frame of REACH (current European Chemical Law: Registration, Evaluation, Authorization and restriction of Chemicals) by the European Union. Hence, a new wet-chemical method free of mercury and chromium(VI) was developed. Manganese(III) was used as oxidant and silver nitrate for the removal of chloride ions. The quantification was performed by back titration of manganese(III) with iron(II) as done in the standard method. In order to minimize losses of organic substances during the precipitation of silver chloride, suspended and colloid organic matter had to be separated by precipitation of aluminum hydroxide in a first step. In these cases, two fractions, one of the suspended and colloid matters and a second of the dissolved organic substances, are prepared and oxidized separately. The method was tested with potassium hydrogen phthalate (KHP) as conventional COD reference substance and different types of wastewater samples. The oxidation of KHP was reproducible in a COD range of 20-500 mg/L with a mean recovery rate of 88.7% in comparison to the standard COD method (DIN 38409-41). Also in presence of 1000 mg/L chloride a recovery rate of 84.1% was reached. For a series of industrial and municipal wastewater samples a high correlation (R 2  = 0.9935) to the standard method with a mean recovery rate of 78.1% (±5.2%) was determined. Even though the results of the new method are not 100% of the standard method, its high correlation to the standard method and reproducibility offers an environmentally benign alternative method with no need to purchase new laboratory equipment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Estimates of Nitrogen, Phosphorus, Biochemical Oxygen Demand, and Fecal Coliforms Entering the Environment Due to Inadequate Sanitation Treatment Technologies in 108 Low and Middle Income Countries.

Science.gov (United States)

Fuhrmeister, Erica R; Schwab, Kellogg J; Julian, Timothy R

2015-10-06

Understanding the excretion and treatment of human waste (feces and urine) in low and middle income countries (LMICs) is necessary to design appropriate waste management strategies. However, excretion and treatment are often difficult to quantify due to decentralization of excreta management. We address this gap by developing a mechanistic, stochastic model to characterize phosphorus, nitrogen, biochemical oxygen demand (BOD), and fecal coliform pollution from human excreta for 108 LMICs. The model estimates excretion and treatment given three scenarios: (1) use of existing sanitation systems, (2) use of World Health Organization-defined "improved sanitation", and (3) use of best available technologies. Our model estimates that more than 10(9) kg/yr each of phosphorus, nitrogen and BOD are produced. Of this, 22(19-27)%, 11(7-15)%, 17(10-23)%, and 35 (23-47)% (mean and 95% range) BOD, nitrogen, phosphorus, and fecal coliforms, respectively, are removed by existing sanitation systems. Our model estimates that upgrading to "improved sanitation" increases mean removal slightly to between 17 and 53%. Under the best available technology scenario, only approximately 60-80% of pollutants are treated. To reduce impact of nutrient and microbial pollution on human and environmental health, improvements in both access to adequate sanitation and sanitation treatment efficiency are needed.

Modelling soil dust aerosol in the Bodélé depression during the BoDEx campaign

OpenAIRE

I. Tegen; B. Heinold; M. Todd; J. Helmert; R. Washington; O. Dubovik; O. Dubovik

2006-01-01

We present regional model simulations of the dust emission events during the Bodélé Dust Experiment (BoDEx) that was carried out in February and March 2005 in Chad. A box model version of the dust emission model is used to test different input parameters for the emission model, and to compare the dust emissions computed with observed wind speeds to those calculated with wind speeds from the regional model simulation. While field observations indicate that dust production occurs via self-abras...

Modeling the performance of 'up-flow anaerobic sludge blanket' reactor based wastewater treatment plant using linear and nonlinear approaches-A case study

Energy Technology Data Exchange (ETDEWEB)

Singh, Kunwar P., E-mail: kpsingh_52@yahoo.com [Environmental Chemistry Division, Indian Institute of Toxicology Research (Council of Scientific and Industrial Research), Post Box No. 80, MG Marg, Lucknow-226 002, UP (India); Basant, Nikita [School of Graduate Studies-Multiscale Modeling, Computational Simulations and Characterization in Material and Life Sciences, University of Modena and Reggio E., Modena (Italy); Malik, Amrita; Jain, Gunja [Environmental Chemistry Division, Indian Institute of Toxicology Research (Council of Scientific and Industrial Research), Post Box No. 80, MG Marg, Lucknow-226 002, UP (India)

2010-01-18

The paper describes linear and nonlinear modeling of the wastewater data for the performance evaluation of an up-flow anaerobic sludge blanket (UASB) reactor based wastewater treatment plant (WWTP). Partial least squares regression (PLSR), multivariate polynomial regression (MPR) and artificial neural networks (ANNs) modeling methods were applied to predict the levels of biochemical oxygen demand (BOD) and chemical oxygen demand (COD) in the UASB reactor effluents using four input variables measured weekly in the influent wastewater during the peak (morning and evening) and non-peak (noon) hours over a period of 48 weeks. The performance of the models was assessed through the root mean squared error (RMSE), relative error of prediction in percentage (REP), the bias, the standard error of prediction (SEP), the coefficient of determination (R{sup 2}), the Nash-Sutcliffe coefficient of efficiency (E{sub f}), and the accuracy factor (A{sub f}), computed from the measured and model predicted values of the dependent variables (BOD, COD) in the WWTP effluents. Goodness of the model fit to the data was also evaluated through the relationship between the residuals and the model predicted values of BOD and COD. Although, the model predicted values of BOD and COD by all the three modeling approaches (PLSR, MPR, ANN) were in good agreement with their respective measured values in the WWTP effluents, the nonlinear models (MPR, ANNs) performed relatively better than the linear ones. These models can be used as a tool for the performance evaluation of the WWTPs.

Modeling the performance of 'up-flow anaerobic sludge blanket' reactor based wastewater treatment plant using linear and nonlinear approaches-A case study

International Nuclear Information System (INIS)

Singh, Kunwar P.; Basant, Nikita; Malik, Amrita; Jain, Gunja

2010-01-01

The paper describes linear and nonlinear modeling of the wastewater data for the performance evaluation of an up-flow anaerobic sludge blanket (UASB) reactor based wastewater treatment plant (WWTP). Partial least squares regression (PLSR), multivariate polynomial regression (MPR) and artificial neural networks (ANNs) modeling methods were applied to predict the levels of biochemical oxygen demand (BOD) and chemical oxygen demand (COD) in the UASB reactor effluents using four input variables measured weekly in the influent wastewater during the peak (morning and evening) and non-peak (noon) hours over a period of 48 weeks. The performance of the models was assessed through the root mean squared error (RMSE), relative error of prediction in percentage (REP), the bias, the standard error of prediction (SEP), the coefficient of determination (R 2 ), the Nash-Sutcliffe coefficient of efficiency (E f ), and the accuracy factor (A f ), computed from the measured and model predicted values of the dependent variables (BOD, COD) in the WWTP effluents. Goodness of the model fit to the data was also evaluated through the relationship between the residuals and the model predicted values of BOD and COD. Although, the model predicted values of BOD and COD by all the three modeling approaches (PLSR, MPR, ANN) were in good agreement with their respective measured values in the WWTP effluents, the nonlinear models (MPR, ANNs) performed relatively better than the linear ones. These models can be used as a tool for the performance evaluation of the WWTPs.

Data on wastewater treatment plant by using wetland method, Babol, Iran

Directory of Open Access Journals (Sweden)

Yousef Dadban Shahamat

2018-02-01

Full Text Available Date in this paper highlights the applications of constructed horizontal surface flow (HF-CW wetland with two different local plants (Louis latifoila and Phragmites -australis (Cav. Trin at the wastewater treatment plant in Babol city. This system was designed as an advanced treatment unit in field scale after the treatment plant. Parameters such as Total Dissolved Solid (TDS, Total Suspended Solid (TSS, Turbidity, Biological Oxygen Demand (BOD and Chemical Oxygen Demand (COD, were investigated. The result shows that treatment efficiency increases with the passage of time. The efficiency of Phragmites planted setups in open environment was fairly good for all studied parameters (28.6% of TDS, 94.4% for TSS, 79.8% for turbidity, 93.7% for BOD and 82.6% for COD. The efficiency of the latifoila set up was also good, but lower than that of Phragmites (26.5% of TDS, 76.9% for TSS, 71.5% for turbidity, 79.1 for BOD and 68.8% for COD. In brief, the obtained dates show that using local plants in (HF-CW wetland not only effectively reduces various contaminants from the effluent of the wastewater according to Effluent Guideline regulations (WHO & EPA, but it is also a cost- effective and environmentally friendly method. Also, it was calculated that in full scale operation [time (1 day and a depth (0.3 m], 8 ha of wetland was needed. Keywords: BOD, Babol, COD, Horizontal subsurface flow wetland, TSS, TSD

Longitudinal data analysis in support of functional stability concepts for leachate management at closed municipal landfills

International Nuclear Information System (INIS)

Gibbons, Robert D.; Morris, Jeremy W.F.; Prucha, Christopher P.; Caldwell, Michael D.; Staley, Bryan F.

2014-01-01

Highlights: • Longitudinal data analysis using a mixed-effects regression model. • Dataset consisted of a total of 1402 samples from 101 closed municipal landfills. • Target analytes and classes generally showed predictable degradation trends. • Validates historical studies focused on macro organic indicators such as BOD. • BOD can serve as “gateway” indicator for planning leachate management. - Abstract: Landfill functional stability provides a target that supports no environmental threat at the relevant point of exposure in the absence of active control systems. With respect to leachate management, this study investigates “gateway” indicators for functional stability in terms of the predictability of leachate characteristics, and thus potential threat to water quality posed by leachate emissions. Historical studies conducted on changes in municipal solid waste (MSW) leachate concentrations over time (longitudinal analysis) have concentrated on indicator compounds, primarily chemical oxygen demand (COD) and biochemical oxygen demand (BOD). However, validation of these studies using an expanded database and larger constituent sets has not been performed. This study evaluated leachate data using a mixed-effects regression model to determine the extent to which leachate constituent degradation can be predicted based on waste age or operational practices. The final dataset analyzed consisted of a total of 1402 samples from 101 MSW landfills. Results from the study indicated that all leachate constituents exhibit a decreasing trend with time in the post-closure period, with 16 of the 25 target analytes and aggregate classes exhibiting a statistically significant trend consistent with well-studied indicators such as BOD. Decreasing trends in BOD concentration after landfill closure can thus be considered representative of trends for many leachate constituents of concern

Longitudinal data analysis in support of functional stability concepts for leachate management at closed municipal landfills

Energy Technology Data Exchange (ETDEWEB)

Gibbons, Robert D., E-mail: rdg@uchicago.edu [Center for Health Statistics, University of Chicago, 5841 S. Maryland Avenue, Chicago, IL 60637 (United States); Morris, Jeremy W.F., E-mail: jmorris@geosyntec.com [Geosyntec Consultants, 10220 Old Columbia Road, Suite A, Columbia, MD 21046 (United States); Prucha, Christopher P., E-mail: cprucha@wm.com [Groundwater Protection Program, Waste Management, 1550 Balmer Road, Box 200, Model City, NY 14107 (United States); Caldwell, Michael D., E-mail: mcaldwell@wm.com [Groundwater Protection Program, Waste Management, 3623 Wilson Road, Humble, TX 77396 (United States); Staley, Bryan F., E-mail: BStaley@erefdn.org [Environmental Research and Education Foundation, 3301 Benson Drive, Suite 301, Raleigh, NC 27609 (United States)

2014-09-15

Highlights: • Longitudinal data analysis using a mixed-effects regression model. • Dataset consisted of a total of 1402 samples from 101 closed municipal landfills. • Target analytes and classes generally showed predictable degradation trends. • Validates historical studies focused on macro organic indicators such as BOD. • BOD can serve as “gateway” indicator for planning leachate management. - Abstract: Landfill functional stability provides a target that supports no environmental threat at the relevant point of exposure in the absence of active control systems. With respect to leachate management, this study investigates “gateway” indicators for functional stability in terms of the predictability of leachate characteristics, and thus potential threat to water quality posed by leachate emissions. Historical studies conducted on changes in municipal solid waste (MSW) leachate concentrations over time (longitudinal analysis) have concentrated on indicator compounds, primarily chemical oxygen demand (COD) and biochemical oxygen demand (BOD). However, validation of these studies using an expanded database and larger constituent sets has not been performed. This study evaluated leachate data using a mixed-effects regression model to determine the extent to which leachate constituent degradation can be predicted based on waste age or operational practices. The final dataset analyzed consisted of a total of 1402 samples from 101 MSW landfills. Results from the study indicated that all leachate constituents exhibit a decreasing trend with time in the post-closure period, with 16 of the 25 target analytes and aggregate classes exhibiting a statistically significant trend consistent with well-studied indicators such as BOD. Decreasing trends in BOD concentration after landfill closure can thus be considered representative of trends for many leachate constituents of concern.

Petrographic study of the Korean anthracite for utilization (VII)

Energy Technology Data Exchange (ETDEWEB)

Park, Hong Soo; Lee, Choon Oh; Park, Suk Whan [Korea Institute of Geology Mining and Materials, Taejon (Korea, Republic of)

1997-12-01

This research was initiated for the development of filtering materials those can be used in waste water treatment sites. The selected Jangseong coal for filtering material has low Hardgrove Grindability Index(HGI:38.38). For feasibility study, the small scale of filtration tester was built on the waste water treatment plant of Samdu dye Co. to use the precipitated water during filtration test processed by purifying system. Measurement items are filtration rate, temperature of waste water, Electric Conductivity(EC), pH, Turbidity, Dissolved Oxygen(DO), Chemical Oxygen Demand (COD), Bio-chemical Oxygen Demand(BOD), Salinity, Total Dissolved solids(TDS) and trace elements content(Zn, Si, Fe, Mg, K, Cu, Sr, Mn, Ca, Na, SO{sub 4}, Ni, Pb, Cd) of the supplied water and filtered water were carried out to find the filtration capacity of coal. The results indicated decreasing degree in turbidity (15.1%), COD(22.1%), BOD(56.8%), color(7.4%) and increasing degree in DO(10.5%). Trace elements removal degree of filtered waste water were about 17.1% for Fe and 10.7% for Zn. (author). 40 refs., 22 tabs., 26 figs.

Linear and nonlinear relationships between biodegradation potential and molecular descriptors/fragments for organic pollutants and a theoretical interpretation

International Nuclear Information System (INIS)

He, Jia; Qin, Weichao; Zhang, Xujia; Wen, Yang; Su, Limin; Zhao, Yuanhui

2013-01-01

Prediction of the biodegradability of organic pollutants is an ecologically desirable and economically feasible tool for estimating the environmental fate of chemicals. In this paper, linear and nonlinear relationships between biological oxygen demand (BOD) and molecular descriptors/fragments have been investigated for 1130 organic chemicals. Significant relationships have been observed between the simple molecular descriptors and %BOD for some homologous compounds, but not for the whole set of compounds. Electronic parameters, such as E HOMO and E LUMO , are the dominant factors affecting the biodegradability for some homologous chemicals. However, other descriptors, such as molecular weight, acid dissociation constant and polarity still have a significant impact on the biodegradation. The best global model for %BOD prediction is that developed from a chain-based fragmentation scheme. At the same time, the theoretical relationship between %BOD and molecular descriptors/fragments has been investigated, based on a first-order kinetic process. The %BOD is nonlinearly, rather than linearly, related to the descriptors. The coefficients of determination can be significantly improved by using nonlinear models for the homologous compounds and the whole data set. After analysing 1130 ready and not ready biodegradable compounds using 23 simple descriptors and various fragmentation schemes, it was revealed that biodegradation could be well predicted from a chain-based fragmentation scheme, a decision tree and a %BOD model. The models were capable of separating NRB and RB with an overall accuracy of 87.2%, 83.0% and 82.5%, respectively. The best classification model developed was a chain-based model but it used 155 fragments. The simplest model was a decision tree which only used 10 structural fragments. The effect of structures on the biodegradation has been analysed and the biodegradation pathway and mechanisms have been discussed based on activating and inactivating

Pengaruh Jumlah Eceng Gondok(eichornia Crassipes) Dan Waktu Tinggal Terhadappenurunan Konsentrasi Cod, Bod, Dan Warnadalam Limbah Batik

OpenAIRE

Wahyu A, Diah; Syafrudin, Syafrudin; Zaman, Badrus

2015-01-01

Batik industries is one of any industries that produce wastewater. According to the previous researches, also known that wastewater of batik industries contain organic substances, suspended solid, color, chromium, phenol, and other. Result of the characteristic test show that BOD concentration is about 130,37 mg/l, COD 1376,29 mg/l, also color 10.000 mg/l PtCo. Treatment for wastewater of batik industries is needed since wastewater can be harm to the environment and it can decrease the enviro...

Emergency material allocation with time-varying supply-demand based on dynamic optimization method for river chemical spills.

Science.gov (United States)

Liu, Jie; Guo, Liang; Jiang, Jiping; Jiang, Dexun; Wang, Peng

2018-04-13

Aiming to minimize the damage caused by river chemical spills, efficient emergency material allocation is critical for an actual emergency rescue decision-making in a quick response. In this study, an emergency material allocation framework based on time-varying supply-demand constraint is developed to allocate emergency material, minimize the emergency response time, and satisfy the dynamic emergency material requirements in post-accident phases dealing with river chemical spills. In this study, the theoretically critical emergency response time is firstly obtained for the emergency material allocation system to select a series of appropriate emergency material warehouses as potential supportive centers. Then, an enumeration method is applied to identify the practically critical emergency response time, the optimum emergency material allocation and replenishment scheme. Finally, the developed framework is applied to a computational experiment based on south-to-north water transfer project in China. The results illustrate that the proposed methodology is a simple and flexible tool for appropriately allocating emergency material to satisfy time-dynamic demands during emergency decision-making. Therefore, the decision-makers can identify an appropriate emergency material allocation scheme in a balance between time-effective and cost-effective objectives under the different emergency pollution conditions.

An Investigation Into The Water Quality Of Buriganga - A River Running Through Dhaka

Directory of Open Access Journals (Sweden)

Shaikh Sayed Ahammed

2015-08-01

Full Text Available Buriganga river is used for bathing drinking irrigation and industrial purposes and is considered to be the lifeline of Dhaka city. The water quality of Buriganga has become a matter of concern due to serious levels of pollution. The objective of the study was to determine the water quality of the selected section of Buriganga river which passes through Dhaka city. The water quality parameters were sampled during different seasons summer winter and autumn and in 10 different sampling points along the river along the banks of the Buriganga River. The water quality parameters studied for this study were dissolved oxygen DO biochemical oxygen demand BOD chemical oxygen demand COD pH turbidity conductivity total dissolved solids TDS nitrate and phosphate. The results showed that DO BOD COD TDS turbidity nitrate and phosphate are at an alarming level and a discussion on the possible sources of the pollution are presented.

The structure optimization of gas-phase surface discharge and its application for dye degradation

Science.gov (United States)

Ying, CAO; Jie, LI; Nan, JIANG; Yan, WU; Kefeng, SHANG; Na, LU

2018-05-01

A gas-phase surface discharge (GSD) was employed to optimize the discharge reactor structure and investigate the dye degradation. A dye mixture of methylene blue, acid orange and methyl orange was used as a model pollutant. The results indicated that the reactor structure of the GSD system with the ratio of tube inner surface area and volume of 2.48, screw pitch between a high-voltage electrode of 9.7 mm, high-voltage electrode wire diameter of 0.8 mm, dielectric tube thickness of 2.0 mm and tube inner diameter of 16.13 mm presented a better ozone (O3) generation efficiency. Furthermore, a larger screw pitch and smaller wire diameter enhanced the O3 generation. After the dye mixture degradation by the optimized GSD system, 73.21% and 50.74% of the chemical oxygen demand (COD) and total organic carbon removal rate were achieved within 20 min, respectively, and the biochemical oxygen demand (BOD) and biodegradability (BOD/COD) improved.

Anaerobic treatment of wastewater with high suspended solids from a bulk drug industry using fixed film reactor (AFFR).

Science.gov (United States)

Gangagni Rao, A; Venkata Naidu, G; Krishna Prasad, K; Chandrasekhar Rao, N; Venkata Mohan, S; Jetty, Annapurna; Sarma, P N

2005-01-01

Studies were carried out on the treatment of wastewater from a bulk drug industry using an anaerobic fixed film reactor (AFFR) designed and fabricated in the laboratory. The chemical oxygen demand (COD) and total dissolved solids (TDS) of the wastewater were found to be very high with low biochemical oxygen demand (BOD) to COD ratio and high total suspended solid (TSS) concentration. Acclimatization of seed consortia and startup of the reactor was carried out by directly using the wastewater, which resulted in reducing the period of startup to 30 days. The reactor was studied at different organic loading rates (OLR) and it was found that the optimum OLR was 10 kg COD/m(3)/day. The wastewater under investigation, which had a considerable quantity of SS, was treated anaerobically without any pretreatment. COD and BOD of the reactor outlet wastewater were monitored and at steady state and optimum OLR 60-70% of COD and 80-90% of BOD were removed. The reactor was subjected to organic shock loads at two different OLR and the reaction could withstand the shocks and performance could be restored to normalcy at that OLR. The results obtained indicated that AFFR could be used efficiently for the treatment of wastewater from a bulk drug industry having high COD, TDS and TSS.

Decoloration and degradation of Reactive Red-120 dye by electron beam irradiation in aqueous solution

International Nuclear Information System (INIS)

Paul, Jhimli; Rawat, K.P.; Sarma, K.S.S.; Sabharwal, S.

2011-01-01

The decoloration and degradation of aqueous solution of the reactive azo dye viz. Reactive Red-120 (RR-120) was carried out by electron beam irradiation. The change in decoloration percentage, removal of chemical oxygen demand (COD) and total organic carbon (TOC), solution pH and five-day biochemical oxygen demand (BOD 5 ) were investigated with respect to the applied dose. However, the concentration of the dye in the solution showed a great influence on all these observables. During the radiolysis process, it was found that the decoloration of dye was caused by the destruction of the chromophore group of the dye molecule, whereas COD and TOC removal were depended on the extent of mineralization of the dye. The decrease in pH during the radiolysis process indicated the fragmentation of the large dye molecule into smaller organic components mostly like smaller organic acids. The BOD 5 /COD ratio of the unirradiated dye solution was in the range of 0.1-0.2, which could be classified as non-biodegradable wastewater. However, the BOD 5 /COD ratio increased upon irradiation and it indicated the transformation of non-biodegradable dye solution into biodegradable solution. This study showed that electron beam irradiation could be a promising method for treatment of textile wastewater containing RR-120 dye.

Source Apportionment of Annual Water Pollution Loads in River Basins by Remote-Sensed Land Cover Classification

Directory of Open Access Journals (Sweden)

Yi Wang

2016-08-01

Full Text Available In this study, in order to determine the efficiency of estimating annual water pollution loads from remote-sensed land cover classification and ground-observed hydrological data, an empirical model was investigated. Remote sensing data imagery from National Oceanic and Atmospheric Administration (NOAA Advanced Very High Resolution Radiometer were applied to an 11 year (1994–2004 water quality dataset for 30 different rivers in Japan. Six water quality indicators—total nitrogen (TN, total phosphorus (TP, biochemical oxygen demand (BOD, chemical oxygen demand (COD, and dissolved oxygen (DO—were examined by using the observed river water quality data and generated land cover map. The TN, TP, BOD, COD, and DO loads were estimated for the 30 river basins using the empirical model. Calibration (1994–1999 and validation (2000–2004 results showed that the proposed simulation technique was useful for predicting water pollution loads in the river basins. We found that vegetation land cover had a larger impact on TP export into all rivers. Urban areas had a very small impact on DO export into rivers, but a relatively large impact on BOD and TN export. The results indicate that the application of land cover data generated from the remote-sensed imagery could give a useful interpretation about the river water quality.

Advanced landfill leachate treatment using iron-carbon microelectrolysis- Fenton process: Process optimization and column experiments.

Science.gov (United States)

Wang, Liqun; Yang, Qi; Wang, Dongbo; Li, Xiaoming; Zeng, Guangming; Li, Zhijun; Deng, Yongchao; Liu, Jun; Yi, Kaixin

2016-11-15

A novel hydrogen peroxide-enhanced iron-carbon (Fe-C) microelectrolysis reactor was proposed for the pretreatment of mature landfill leachate. This reactor, combining microelectrolysis with Fenton process, revealed high treatment efficiency. The operating variables, including Fe-C dosage, H2O2 concentration and initial pH, were optimized by the response surface methodology (RSM), regarding the chemical oxygen demand (COD) removal efficiency and biochemical oxygen demand: chemical oxygen demand (BOD5/COD) as the responses. The highest COD removal (74.59%) and BOD5/COD (0.50) was obtained at optimal conditions of Fe-C dosage 55.72g/L, H2O2 concentration 12.32mL/L and initial pH 3.12. Three-dimensional excitation and emission matrix (3D-EEM) fluorescence spectroscopy and molecular weight (MW) distribution demonstrated that high molecular weight fractions such as refractory fulvic-like substances in leachate were effectively destroyed during the combined processes, which should be attributed to the combination oxidative effect of microelectrolysis and Fenton. The fixed-bed column experiments were performed and the breakthrough curves at different flow rates were evaluated to determine the practical applicability of the combined process. All these results show that the hydrogen peroxide-enhanced iron-carbon (Fe-C) microelectrolysis reactor is a promising and efficient technology for the treatment of mature landfill leachate. Copyright © 2016 Elsevier B.V. All rights reserved.

Application of H2O and UV/H2O2 processes for enhancing the biodegradability of reactive black 5 dye.

Science.gov (United States)

Kalpana, S Divya; Kalyanaraman, Chitra; Gandhi, N Nagendra

2011-07-01

Leather processing is a traditional activity in India during which many organic and inorganic chemicals are added while part of it is absorbed by the leather, the remaining chemicals are discharged along with the effluent. The effluent contains both easily biodegradable and not easily biodegradable synthetic organics like dyes, syntans. Easily biodegradable organics are removed in the existing biological treatment units whereas synthetic organics present in the wastewater are mostly adsorbed over the microbes. As the tannery effluent contains complex chemicals, it is difficult to ascertain the degradation of specific pollutants. To determine the increase in the biodegradability, one of the complex and synthetic organic chemical like dye used in the tanning operation was selected for Advanced Oxidation Process (AOPs) treatment for cleaving complex organics and its subsequent treatment in aerobic process. In the present study, Reactive Black 5 Dye used in the tanning operation was selected for Hydrogen Peroxide (H2O2) and UV/H2O2 pre-treatment for different operating conditions like pH, contact time and different volume of H2O2. A comparison was made between the untreated, Hydrogen Peroxide (H2O2) and UV/H2O2 treated effluent in order to ascertain the influence of AOP on the improvement of biodegradability of effluent. An increase in the BOD5/COD ratio from 0.21 to 0.435 was achieved in the UV/H2O2 pre-treatment process. This pre-treated effluent was further subjected to aerobic process. Biochemical Oxygen Demand (BOD5) and Chemical Oxygen Demand (COD) removal efficiency of the UV/H2O2 pre-treated dye solution in the aerobic process was found to be 86.39% and 77.82% when compared to 52.43% of BOD5 and 51.55% of COD removal efficiency without any pre-treatment. Hence from these results, to increase the biodegradability of Reactive Black 5 dye pre-treatment methods like H2O2 and UV/H2O2 can be used prior to biological treatment process.

Assessing the Ecological Relevance of Organic Discharge Limits for Constructed Wetlands by Means of a Model-Based Analysis

Directory of Open Access Journals (Sweden)

Natalia Donoso

2018-01-01

Full Text Available Polder watercourses within agricultural areas are affected by high chemical oxygen demand (COD and biological oxygen demand (BOD5 concentrations, due to intensive farming activities and runoff. Practical cases have shown that constructed wetlands (CWs are eco-friendly and cost-effective treatment systems which can reduce high levels of organic and nutrient pollution from agricultural discharges. However, accumulated recalcitrant organic matter, originated by in-situ sources or elements of CWs (i.e., plants or microbial detritus, limits the fulfilment of current COD discharge threshold. Thus, to evaluate its relevance regarding rivers ecosystem health preservation, we analysed the response of bio-indicators, the Multimetric Macroinvertebrate Index Flanders (MMIF and the occurrence of organic pollution sensitive taxa towards organic pollutants. For this purpose, statistical models were developed based on collected data in polder watercourses and CWs located in Flanders (Belgium. Results showed that, given the correlation between COD and BOD5, both parameters can be used to indicate the ecological and water quality conditions. However, the variability of the MMIF and the occurrence of sensitive species are explained better by BOD5, which captures a major part of their common effect. Whereas, recalcitrant COD and the interaction among other physico-chemical variables indicate a minor variability on the bio-indicators. Based on these outcomes we suggest a critical re-evaluation of current COD thresholds and moreover, consider other emerging technologies determining organic pollution levels, since this could support the feasibility of the implementation of CWs to tackle agricultural pollution.

EFFECT OF TROUT PRODUCTION IN CONCRETE PONDS WITH A CASCADING FLOW OF WATER ON PHYSICAL AND CHEMICAL PROPERTY OF WATER

Directory of Open Access Journals (Sweden)

Marcin Sidoruk

2014-10-01

Full Text Available Fish rearing causes changes in water quality due to the use of feed, mineral and organic fertilizers, pharmaceuticals and disinfectants. Rational fishery management aims to maintain or restore the quality of water in natural ecosystems. Cultures produce a certain amount of waste and pollutants released into the environment with waters departing from ponds, but their harmfulness depends on the conditions and type of farming. Studies on the assessment of the effects of rearing trout on physical and chemical properties of surface water were carried out in 2010-2012. Were chosen trout farm located in the Pomeranian province about 36 miles southeast of Słupsk. Water samples for physical and chemical analysis were collected every two months (a total of 12 sets samples collected and labeled them: temperature [°C], dissolved oxygen [mg · dm-3], oxygen saturation [%] electrolytic conductivity [S · cm-1], pH, redox potential [mV] and BOD5 and CODCr. The study showed that the water used to supply breeding facilities meet the requirements to be met which are inland water salmonid habitat. Only periodically for BOD5 standards have been slightly exceeded. After passing through the joints deterioration of water quality did not cause a change in the quality of the class, if only temporarily BOD5 ratio were lower in its quality from the first to the third class.

Diurnal variations in wastewater characteristics at main out fall in Lahore

International Nuclear Information System (INIS)

Haider, H.; Ali, W.; Ali, W.

2012-01-01

Variations in the flow and pollutants concentrations during the day were monitored at the Main Out fall disposal station of the city of Lahore. The laboratory analysis of the wastewater samples collected at 2 hour interval on fifth and sixth May, 2009 for pH, temperature, alkalinity, hardness, Biochemical Oxygen Demand (BOD5), BOD5 Filtered, Total Kjeldahl Nitrogen (TKN), Ammonia Nitrogen (NH/sub 3/-N), chlorides, solids, turbidity, sulphates and nitrates were carried out. Average values and standard deviations were determined to assess the type of wastewater treatment. Correlation between BOD5 and BOD5 Filtered was developed through regression analysis. Diurnal variations in the Ultimate Biochemical Oxygen Demand (BODU) at the Main Out fall based on Carbonaceous Biochemical Oxygen Demand (CBODU) and Nitrogenous Biochemical Oxygen Demand (NBODU) are also estimated. The ratio between CBODU/NBODU ranges between 0.86 to 1.8 during a day at Main Out fall. This variation is primarily due to the large diurnal variation in CBODU values as a result of industrial activities in the study area. The BOD5/ TKN ratio varies between 3.3 and 6.9 and the calculated BODU (i.e., CBODU + NBODU) was found to be almost double of BOD5 during most part of the day primarily due to inclusion of NBOD. The study results reveal the importance of NBOD while designing the wastewater treatment facilities and implementing a water quality control strategy for the River Ravi. (author)

Physicochemical Characteristics of Pennar River, A Fresh Water Wetland in Kerala, India

Directory of Open Access Journals (Sweden)

P. V. Joseph

2010-01-01

Full Text Available Some physicochemical characteristics of a fresh water wetland were investigated. The analysis was carried out for a period of two years. Physical parameters such as colour, odour, temperature, electrical conductivity (EC total suspended solids (TSS total dissolved substances (TDS, total solids (TS, turbidity and chemical parameters such as pH, alkalinity, hardness, dissolved oxygen (DO, biochemical oxygen demand (BOD, chemical oxygen demand (COD, chloride, salinity, flouride, phosphate & nitrate were examined. Results of the study indicated that water in Pennar river is highly contaminated and not safe for drinking. Uncontrolled use of chemical fertilizers and pesticides, unscrupulous dumping of domestic wastes are the major causes of deterioration of water. Poor quality of drinking water was recorded as the major risk factor for the large-scale water-borne diseases in the area.

Simulation of Constructed Wetland in treating Wastewater using Fuzzy Logic Technique

Science.gov (United States)

Sudarsan, J. S.; Subramani, Sheekha; Rajan, Rajitha J.; Shah, Isha; Nithiyanantham, S.

2018-04-01

Constructed wetlands act as a natural alternative to conventional methods of wastewater treatment. CW are found effective in wastewater containing inorganic matter, organic matter, toxic compounds, metals, nitrogen, phosphorous, heavy metals, organic chemicals, and pathogens. The treatment efficiency by the adaptation of CWs in treatment process is achieved by a complex interaction between plants, microorganisms, soil matrix and substances in the wastewater. Constructed wetland treatment systems are engineered systems designed in such a manner that it could take advantages of those processes occurring in natural wetlands in treating the wastewater concerned, but in a more controlled environment. Petrochemical wastewater was the type of wastewater taken for the study. Characteristics of petrochemical wastewater mainly oil, Biological Oxygen Demand (BOD) and Chemical oxygen demand (COD) were selected for treatment in constructed wetland as they are predominant in petrochemical wastewater. The conventional methods followed in the treatment are chemical and biological treatment. In this study, a fuzzy model for water quality assessment has been developed and water quality index value was obtained. The experiment conducted and further analysis using fuzzy logic indicated that interpretation of certain imprecise data can be improved within fuzzy inference system (FIS). Based on the analysis, we could observe that Typha sp contained wetland cell showed greater efficiency in removal of parameters such as COD and BOD than Phragmites sp. wetland cell.

Research progress of on-line automatic monitoring of chemical oxygen demand (COD) of water

Science.gov (United States)

Cai, Youfa; Fu, Xing; Gao, Xiaolu; Li, Lianyin

2018-02-01

With the increasingly stricter control of pollutant emission in China, the on-line automatic monitoring of water quality is particularly urgent. The chemical oxygen demand (COD) is a comprehensive index to measure the contamination caused by organic matters, and thus it is taken as one important index of energy-saving and emission reduction in China’s “Twelve-Five” program. So far, the COD on-line automatic monitoring instrument has played an important role in the field of sewage monitoring. This paper reviews the existing methods to achieve on-line automatic monitoring of COD, and on the basis, points out the future trend of the COD on-line automatic monitoring instruments.

Treatment of high organic content wastewater from food-processing industry with the French vertical flow constructed wetland system.

Science.gov (United States)

Paing, J; Serdobbel, V; Welschbillig, M; Calvez, M; Gagnon, V; Chazarenc, F

2015-01-01

This study aimed at determining the treatment performances of a full-scale vertical flow constructed wetlands designed to treat wastewater from a food-processing industry (cookie factory), and to study the influence of the organic loading rate. The full-scale treatment plant was designed with a first vertical stage of 630 m², a second vertical stage of 473 m² equipped with a recirculation system and followed by a final horizontal stage of 440 m². The plant was commissioned in 2011, and was operated at different loading rates during 16 months for the purpose of this study. Treatment performances were determined by 24 hour composite samples. The mean concentration of the raw effluent was 8,548 mg.L(-1) chemical oxygen demand (COD), 4,334 mg.L(-1) biochemical oxygen demand (BOD5), and 2,069 mg.L(-1) suspended solids (SS). Despite low nutrients content with a BOD5/N/P ratio of 100/1.8/0.5, lower than optimum for biological degradation (known as 100/5/1), mean removal performances were very high with 98% for COD, 99% for BOD5 and SS for the two vertical stages. The increasing of the organic load from 50 g.m(-2).d(-1) COD to 237 g.m(-2).d(-1) COD (on the first stage) did not affect removal performances. The mean quality of effluent reached French standards (COD < 125 mg.L(-1), BOD5 < 25 mg.L(-1), SS < 35 mg.L(-1)).

In situ microbial fuel cell-based biosensor for organic carbon

DEFF Research Database (Denmark)

de Jesus dos Santos Peixoto, Luciana; Min, Booki; Martins, Gilberto

2011-01-01

The biological oxygen demand (BOD) may be the most used test to assess the amount of pollutant organic matter in water; however, it is time and labor consuming, and is done ex-situ. A BOD biosensor based on the microbial fuel cell principle was tested for online and in situ monitoring of biodegra......The biological oxygen demand (BOD) may be the most used test to assess the amount of pollutant organic matter in water; however, it is time and labor consuming, and is done ex-situ. A BOD biosensor based on the microbial fuel cell principle was tested for online and in situ monitoring...... of biodegradable organic content of domestic wastewater. A stable current density of 282±23mA/m2 was obtained with domestic wastewater containing a BOD5 of 317±15mg O2/L at 22±2°C, 1.53±0.04mS/cm and pH 6.9±0.1. The current density showed a linear relationship with BOD5 concentration ranging from 17±0.5mg O2/L...

Biogas Production and Removal COD – BOD and TSS from Wastewater Industrial Alcohol (Vinasse by Modified UASB Bioreactor

Directory of Open Access Journals (Sweden)

Utami Isni

2016-01-01

Full Text Available Biogas production and decreased organic loading of vinasse using a modified UASB bioreactor has been done successfully. Vinasse is waste from the ethanol industry which contains COD: 9.360 mg / L , BOD : 4.013 mg/L, and TSS: 317.5 mg/L. The purpose of this research was to study the performance of bioreactors Upflow Anaerobic Sludge Blanket (UASB to decompose the vinasse into biogas or methane. UASB operating principle is to distribute wastewater in the bioreactor to flow upward through the sludge blanket by setting the hidrolic retention time (HRT. Four UASB bioreactor columns were used in this experiment wherein each with a capacity of 50 L in volume; 23 cm inside diameter, and 120 cm. The variations of hydraulic capacity followed the variations of HRT in the range of 72-36 hours. Modifications were carried out on the top of column UASB with the aim of preventing gas losses and increasing the flowrate of gas out from the top of the column. The results showed that HRT increased from 36 h to 72 h followed by an increase in COD removal efficiency of 55.64% to 66.81%; BOD5 from 67.85% to 74.58%; and TSS from 66.69% to 84.19%. The maximum volume of biogas produced was in the range of 5.826 L / day (42.89% methane to 7.930 L / day (methane 58.06%.

Possible penetration of nuclear power in fuel and energy demand structure in chemical industry

International Nuclear Information System (INIS)

Balajka, J.

1986-01-01

Three basic technologies based on methane steam reforming using nuclear heating were assessed with respect of a simplified diagram of a link between a high temperature reactor and chemical technology. They included the technologies of production of methanol, hydrogen and ammonia which differ in the gradually increasing exothermal character of the fission gas processing into the resulting synthesis gas (methanol, ammonia) or the gaseous product (hydrogen). In dependence on the degree of available power from the high temperature reactor for steam reforming, the efficiency of the cycle of the synthesis gas preparation, the power demand, and the balance of the associated electric power generation and the capacity of the production unit were evaluated. (author)

Olive mill wastewater disposal in evaporation ponds in Sfax (Tunisia): moisture content effect on microbiological and physical chemical parameters.

Science.gov (United States)

Jarboui, Raja; Hadrich, Bilel; Gharsallah, Néji; Ammar, Emna

2009-11-01

The study of the isotherms desorption of olive mill wastewater (OMW) was investigated to describe its water activity under different saturated environments. The microbial biodegradation of OMW during its storage in 5 evaporation ponds located in Agareb (Sfax-Tunisia) was carried out during the oil-harvesting year held 105 days in 2004. Gravimetric static method using saturated salt solutions was used and OMW as placed at 30 degrees C and under different water activities ranging from 0.11 to 0.90. Eight models were taken from the literature to describe experimental desorption isotherms. During storage, the evolution of physico-chemical parameters including pH, temperature, evaporation, humidity, total phosphorus, chemical oxygen demand (COD), biological oxygen demand (BOD) and phenols and three microbiological flora (aerobic mesophilic bacteria, yeasts and moulds) were considered. At 30 degrees C, when relative humidity increased in the experimented ponds of 69, 84 and 90%, the evaporation speed decreased from 1.24 x 10(-5) to 5 x 10(-6) cm(3) s(-1), from 6 x 10(-5) to 7 x 10(-6) cm(3) s(-1) and from 5 x 10(-6) to 1.1 x 10(-7) cm(3) s(-1) respectively. The desorption isotherm exhibited a sigmoidal curve corresponding to type II, typical of many organic material. The GAB and Peleg models gave the best fit for describing the relationship between the equilibrium moisture content and water activity in OMW (R (2) = 0.998). During the storage period, the analysis showed an increase of all the physico-chemical parameters studied, except phenols and total phosphorus concentrations. The microbiological study showed the predominance of yeasts and moulds and the decrease of bacteria population after 75 days reflecting both effect of recalcitrant compounds and the water activity on microbial growth.

Enhancement of biodegradability of real textile and dyeing wastewater by electron beam irradiation

International Nuclear Information System (INIS)

He, Shijun; Sun, Weihua; Wang, Jianlong; Chen, Lvjun; Zhang, Youxue; Yu, Jiang

2016-01-01

A textile and dyeing wastewater treatment plant is going to be upgraded due to the stringent discharge standards in Jiangsu province, China, and electron beam irradiation is considering to be used. In order to determine the suitable location of the electron accelerator in the process of wastewater treatment plant, the effects of electron beam (EB) irradiation on the biodegradability of various real wastewater samples collecting from the different stages of the wastewater treatment plant, the values of chemical oxygen demand (COD), biochemical oxygen demand (BOD 5 ), and the ratio of BOD 5 and COD (BOD 5 /COD), were compared before and after EB irradiation. During EB irradiation process, color indices and absorbance at 254 nm wavelength (UV 254 ) of wastewater were also determined. The results showed that EB irradiation pre-treatment cannot improve the biodegradability of raw textile and dyeing wastewater, which contains a large amount of biodegradable organic matters. In contrast, as to the final effluent of biological treatment process, EB irradiation can enhance the biodegradability to 224%. Therefore, the promising way is to apply EB irradiation as a post-treatment of the conventional biological process. - Highlights: • Irradiation pre-treatment did not improve the raw textile wastewater biodegradability. • Irradiation can highly enhance the biodegradability of biological treated effluent. • EB irradiation can be used as a post-treatment after biological process.

Use of native aquatic macrophytes in the reduction of organic matter from dairy effluents.

Science.gov (United States)

Queiroz, Rita de Cássia Souza de; Andrade, Rodrigo Santos; Dantas, Isadora Rosário; Ribeiro, Vinícius de Souza; Neto, Luciano Brito Rodrigues; Almeida Neto, José Adolfo de

2017-08-03

Considering the diversity and the unexplored potential of regional aquatic flora, this study aimed to identify and analyze the potential of native aquatic macrophytes to reduce the organic matter of dairy wastewater (DW) using experimental constructed wetlands. The dairy wastewater (DW) had an average chemical oxygen demand (COD) of 7414.63 mg/L and then was diluted to 3133.16 mg/L (D1) and to 2506.53 mg/L (D2). Total solids, COD, temperature, and pH analyses were performed, and the biochemical oxygen demand (BOD) was estimated from the COD values. The best performance in the reduction of the organic matter was observed for Polygonum sp. (87.5% COD and 79.6% BOD) and Eichhornia paniculata (90% COD and 83.7% BOD) at dilution D1, on the 8th day of the experiment. However, the highest total solids removal was observed for Polygonum sp. (32.2%), on the 4th day, at dilution D2. The total solid (TS) concentration has also increased starting from the 8th day of the experiment was observed which may have been due to the development of mosquito larvae and their mechanical removal by sieving, thus changing the steady state of the experimental systems. The macrophytes Polygonum sp. and E. paniculata were considered suitable for the reduction of organic matter of DW using constructed wetlands.

Tannery Effluent Treatment by Yeast Species Isolates from Watermelon

Directory of Open Access Journals (Sweden)

Stanley Irobekhian Reuben Okoduwa

2017-02-01

Full Text Available The quest for an effective alternative means for effluent treatment is a major concern of the modern-day scientist. Fungi have been attracting a growing interest for the biological treatment of industrial wastewater. In this study, Saccharomycescerevisiae and Torulasporadelbrueckii were isolated from spoiled watermelon and inoculated into different concentrations of effluent. The inoculants were incubated for 21-days to monitor the performance of the isolates by measurement of biochemical oxygen demand (BOD, chemical oxygen demand (COD, nitrates, conductivity, phosphates, sulphates and turbidity. The results showed that Saccharomycescerevisiae had the highest percentage decrease of 98.1%, 83.0%, 60.7%, 60.5%, and 54.2% for turbidity, sulphates, BOD, phosphates and COD, respectively, of the tannery effluent. Torulasporadelbrueckii showed the highest percentage decrease of 92.9%, 90.6%, and 61.9% for sulphates, COD, and phosphates, respectively, while the syndicate showed the highest percentage reduction of 87.4% and 70.2% for nitrate and total dissolve solid (TDS, respectively. The least percentage decrease was displayed by syndicate organisms at 51.2%, 48.1% and 40.3% for BOD, COD and conductivity, respectively. The study revealed that Saccharomycescerevisiae and Torulasporadelbrueckii could be used in the biological treatment of tannery-effluent. Hence, it was concluded that the use of these organisms could contribute to minimizing the adverse environmental risks and health-hazards associated with the disposal of untreated tannery-effluents.

Olive mill wastewater treatment in Jordan: A Review

Science.gov (United States)

Bawab, Abeer Al; Ghannam, Noor; Abu-Mallouh, Saida; Bozeya, Ayat; Abu-Zurayk, Rund A.; Al-Ajlouni, Yazan A.; Alshawawreh, Fida'a.; Odeh, Fadwa; Abu-Dalo, Muna A.

2018-02-01

The environmental impact of olive mill wastewater (OMW) pollution is a public concern. OMW contains high levels of phenols, organic compounds, chemical oxygen demand (COD), biological oxygen demand (BOD), microorganisms, nutrients, and toxic compounds. The treatment of OMW has been investigated by many researchers in the Mediterranean region, using several treatment techniques to remove contaminants from OMW. These techniques include chemical, biological, physiochemical, and biophysical techniques. Surfactants and some adsorbents were used in chemical techniques, anaerobic and aerobic in biological techniques, while the combined treatment methods used Electroosmosis, ozonation and electrocoagulation processes as physiochemical methods, and ultrasonic irradiation combined with aerobic biodegradation as biophysical method. The effects of OMW, whether treated or untreated, have been evaluated on both plants’ growth and soil properties. The treatment methods as well as the environmental impact of OMW in Jordan were summarized in this review.

Sequencing treatment of industrial wastewater with ultraviolet/H2O2 advanced oxidation and moving bed bioreactor

Directory of Open Access Journals (Sweden)

Mohammad Mehdi Mehrabani Ardekani

2015-01-01

Full Text Available Aims: The main purpose of this study was to determine the efficiency of a sequencing treatment including ultraviolet (UV/H 2 O 2 oxidation followed by a moving bed bioreactor (MBBR. Materials and Methods: Effect of solution pH, reaction time, and H 2 O 2 concentration were investigated for an industrial wastewater sample. The effluent of the advanced oxidation processes unit was introduced to the MBBR operated for three hydraulic retention times of 4, 8, and 12 h. Results: The optimum condition for industrial wastewater treatment via advanced oxidation was solution pH: 7, H 2 O 2 dose: 1000 mg/L and 90 min reaction time. These conditions led to 74.68% chemical oxygen demand (COD removal and 66.15% biochemical oxygen demand (BOD 5 removal from presedimentation step effluent that initially had COD and BOD 5 contents of 4,400 and 1,950 mg/L, respectively. Conclusion: Combination of UV/H 2 O 2 advanced oxidation with MBBR could result in effluents that meet water quality standards for discharge to receiving waters.

Disinfection of wastewater from a Riyadh Wastewater Treatment Plant with ionizing radiation

International Nuclear Information System (INIS)

Basfar, A.A.; Abdel Rehim, F.

2002-01-01

The goal of this research was to establish the applicability of the electron beam treatment process for treating wastewater intended for reuse. The objective of this study was to determine the effectiveness of gamma irradiation in the disinfection of wastewater, and the improvement of the water quality by determining the changes in organic matter as indicated by the measurement of biochemical oxygen demand (BOD), chemical oxygen demand (COD) and total organic carbon (TOC). Samples of effluent, before and after chlorination, and sludge were obtained from a Riyadh Wastewater Treatment Plant. The studies were conducted using a laboratory scale 60 Co gamma source. The improvement in quality of the irradiated samples was demonstrated by the reduction in bacteria, and the reduction in the BOD, COD and TOC. Radiation of the wastewater provided adequate disinfection while at the same time increasing the water quality. This treatment could lead to additional opportunities for the reuse of this valuable resource. Limited studies, conducted on the anaerobically digested secondary biosolids, showed an improvement in bacterial content and no change in COD

Non-biodegradable landfill leachate treatment by combined process of agitation, coagulation, SBR and filtration.

Science.gov (United States)

Abood, Alkhafaji R; Bao, Jianguo; Du, Jiangkun; Zheng, Dan; Luo, Ye

2014-02-01

This study describes the complete treatment of non-biodegradable landfill leachate by combined treatment processes. The processes consist of agitation as a novel stripping method used to overcome the ammonia toxicity regarding aerobic microorganisms. The NH3-N removal ratio was 93.9% obtained at pH 11.5 and a gradient velocity (G) 150 s(-1) within a five-hour agitation time. By poly ferric sulphate (PFS) coagulation followed the agitation process; chemical oxygen demand (COD) and biological oxygen demand (BOD5) were removed at 70.6% and 49.4%, respectively at an optimum dose of 1200 mg L(-1) at pH 5.0. The biodegradable ratio BOD5/COD was improved from 0.18 to 0.31 during pretreatment step by agitation and PFS coagulation. Thereafter, the effluent was diluted with sewage at a different ratio before it was subjected to sequencing batch reactor (SBR) treatment. Up to 93.3% BOD5, 95.5% COD and 98.1% NH3-N removal were achieved by SBR operated under anoxic-aerobic-anoxic conditions. The filtration process was carried out using sand and carbon as a dual filter media as polishing process. The final effluent concentration of COD, BOD5, suspended solid (SS), NH3-N and total organic carbon (TOC) were 72.4 mg L(-1), 22.8 mg L(-1), 24.2 mg L(-1), 18.4 mg L(-1) and 50.8 mg L(-1) respectively, which met the discharge standard. The results indicated that a combined process of agitation-coagulation-SBR and filtration effectively eliminated pollutant loading from landfill leachate. Copyright © 2013 Elsevier Ltd. All rights reserved.

Effects of Three Types of Oil Dispersants on Biodegradation of Dispersed Crude Oil in Water Surrounding Two Persian Gulf Provinces

Directory of Open Access Journals (Sweden)

Azadeh Zolfaghari-Baghbaderani

2012-01-01

Full Text Available Objective. To determine the most effective and biodegradable dispersant of spilled oil in water surrounding two Persian Gulf provinces. Methods. This study compared the effects of three dispersants, Pars 1, Pars 2, and Gamlen OD4000 on removal of oil in two Persian Gulf provinces' water. Overall, 16 stations were selected. Using the Well method, the growth rate of isolated bacteria and fungi was identified. To specify the growth rate of microorganisms and their usage of oil in the presence of the above-mentioned dispersants, as exclusive sources of carbon, the bacteria were grown in culture medium for 28 days at 120 rpm, 30∘C, and their optical density was measured by spectrophotometry. Then, we tested biological oxygen demand (BOD and chemical oxygen demand (COD in microorganisms. Results. The highest growth rate was documented for the growth of microorganisms on either Pars 1 or Pars 2 dispersants or their mixtures with oil. However, the culture having microorganisms grown on Pars 1 had higher BOD and COD than the other two dispersants (9200 and 16800 versus 500 and 960, P<0.05. Mixture of oil and Pars 2 as well as oil and Pars 1 dispersants showed the highest BODs and CODs, respectively. In the Bahregan province, microorganisms grown on Pars 2 had maximum amount of BOD and COD in comparison with Pars 1 and Gamlen dispersants (7100 and 15200 versus 6000 and 10560, P<0.05. Conclusion. Pars 1 and Pars 2 were the most effective dispersants with highest degradability comparing Gamlen. In each region, the most suitable compound for removing oil spill from offshores with least secondary contamination should be investigated.

Effects of Three Types of Oil Dispersants on Biodegradation of Dispersed Crude Oil in Water Surrounding Two Persian Gulf Provinces

International Nuclear Information System (INIS)

Zolfaghari-Baghbaderani, A.; Bijani, S.; Zolfaghari-Baghbaderani, A.; Bijani, S.; Emtyazjoo, M.; Emtyazjoo, M.; Poursafa, P.; Mehrabian, S.; Farkhani, D.; Mirmoghtadaee, P.

2012-01-01

Objective. To determine the most effective and biodegradable dispersant of spilled oil in water surrounding two Persian Gulf provinces. Methods. This study compared the effects of three dispersants, Pars 1, Pars 2, and Gamlen OD4000 on removal of oil in two Persian Gulf provinces' water. Overall, 16 stations were selected. Using the Well method, the growth rate of isolated bacteria and fungi was identified. To specify the growth rate of microorganisms and their usage of oil in the presence of the above-mentioned dispersants, as exclusive sources of carbon, the bacteria were grown in culture medium for 28 days at 120 rpm, 30 C, and their optical density was measured by spectrophotometry. Then, we tested biological oxygen demand (BOD) and chemical oxygen demand (COD) in microorganisms. Results. The highest growth rate was documented for the growth of microorganisms on either Pars 1 or Pars 2 dispersants or their mixtures with oil. However, the culture having microorganisms grown on Pars 1 had higher BOD and COD than the other two dispersants (9200 and 16800 versus 500 and 960, P<0.05). Mixture of oil and Pars 2 as well as oil and Pars 1 dispersants showed the highest BODs and CODs, respectively. In the Bahregan province, microorganisms grown on Pars 2 had maximum amount of BOD and COD in comparison with Pars 1 and Gamlen dispersants (7100 and 15200 versus 6000 and 10560, P<0.05). Conclusion. Pars 1 and Pars 2 were the most effective dispersants with highest degradability comparing Gamlen. In each region, the most suitable compound for removing oil spill from off shores with least secondary contamination should be investigated.

Nitrogen and chemical oxygen demand removal from septic tank wastewater in subsurface flow constructed wetlands: substrate (cation exchange capacity) effects.

Science.gov (United States)

Collison, Robert S; Grismer, Mark E

2014-04-01

The current article focuses on chemical oxygen demand (COD) and nitrogen (ammonium and nitrate) removal performance from synthetic human wastewater as affected by different substrate rocks having a range of porosities and cation exchange capacities (CECs). The aggregates included lava rock, lightweight expanded shale, meta-basalt (control), and zeolite. The first three had CECs of 1 to 4 mequiv/100 gm, whereas the zeolite CEC was much greater (-80 mequiv/100 gm). Synthetic wastewater was gravity fed to each constructed wetland system, resulting in a 4-day retention time. Effluent samples were collected, and COD and nitrogen species concentrations measured regularly during four time periods from November 2008 through June 2009. Chemical oxygen demand and nitrogen removal fractions were not significantly different between the field and laboratory constructed wetland systems when corrected for temperature. Similarly, overall COD and nitrogen removal fractions were practically the same for the aggregate substrates. The important difference between aggregate effects was the zeolite's ammonia removal process, which was primarily by adsorption. The resulting single-stage nitrogen removal process may be an alternative to nitrification and denitrification that may realize significant cost savings in practice.

Pemanfaatan Abu Tandan Kosong Kelapa Sawit Untuk Menurunkan Kandungan Minyak/Lemak BOD Dan COD Dari Limbah Cair Pabrik Kelapa Sawit

OpenAIRE

Sari, Riris Duma

2011-01-01

An investigation of the utilization of oil palm empty fruit bunch ash to reduce the content of oil/grease, BOD and COD from oil mill effluent. Samples of palm oil mill effluent from wastewater treatment plant of PT Nusantara IV (Persero) oil processing unit sopsa of Padang Lawas district. Samples taken from the last pond will be discharged into the environment. Empty Fruit of Oil Palm Ash taken from the kitchen burning empty fruit bunches PT Nusantara IVB (Persero) units Sosa of Padang Law...

Sampling and sample handling procedures for priority pollutants in surface coal mining wastewaters. [Detailed list to be analyzed for

Energy Technology Data Exchange (ETDEWEB)

Hayden, R. S.; Johnson, D. O.; Henricks, J. D.

1979-03-01

The report describes the procedures used by Argonne National Laboratory to sample surface coal mine effluents in order to obtain field and laboratory data on 110 organic compounds or classes of compounds and 14 metals and minerals that are known as priority pollutants, plus 5-day biochemical oxygen demand (BOD/sub 5/), total organic carbon (TOC), chemical oxygen demand (COD), total dissolved solids (TDS), and total suspended solids (TSS). Included are directions for preparation of sampling containers and equipment, methods of sampling and sample preservation, and field and laboratory protocols, including chain-of-custody procedures. Actual analytical procedures are not described, but their sources are referenced.

Reduction of Wastewater Pollutants of Mandalay City Slaughterhouse

International Nuclear Information System (INIS)

May Thant Zin; Sint Soe

2010-12-01

Slaughterhouse (Meat Production Factor)under Mandaly City Development Committee (MCDC) in Myanmar has been discharging raw wastewater directly into Tat Thay Pont which is located at the back side of the slaughterhouse.It can cause some water pollutants in water source and need to prevent environmental impact. This paper was studied on the treatment of slaughterhouse wastewater using appropriate technique available in local area. Sample collection of slaughterhouse waste, analysing of waste quality on current situation,different ways of pre-treating and anaerobically digestion without recycling were done. Screening, coagulation, sedimentation and charcoal filtration were included as pre-treating steps before major anaerobic digestion. Ferric chloride and aluminum sulphate chemicals of both commercial and analytical grades were used as coagulants. Laboratory-scaled anaerobic reactor constructed with polyvinyl chloride (PVC) material was 15 cm diameter and 90 cm heigh. MCDC slaughterhouse wastewater containing 98.56% of total coarse particles was removed via minimum size of 1500 micron screen. Aluminium sulphate gave the best removal of fine solid particles. It was observed that pre-treating steps can reduce 56.72% of initial biological oxygen demand (BOD), 51.482% of initial chemical oxygen demand (COD) and 45.18% of inital total suspended solid (TSS) and anaerobic digester after 30 days can reduce 77.4% of influent BOD,81.5% of influent COD and 87.3% of influent TSS.

Degradation and biodegradability improvement of the olive mill wastewater by peroxi-electrocoagulation/electrooxidation-electroflotation process with bipolar aluminum electrodes.

Science.gov (United States)

Esfandyari, Yahya; Mahdavi, Yousef; Seyedsalehi, Mahdi; Hoseini, Mohammad; Safari, Gholam Hossein; Ghozikali, Mohammad Ghanbari; Kamani, Hossein; Jaafari, Jalil

2015-04-01

Olive mill wastewater is considered as one of the most polluting effluents of the food industry and constitutes a source of important environmental problems. In this study, the removal of pollutants (chemical oxygen demand (COD), biochemical oxygen demand (BOD5), polyphenols, turbidity, color, total suspended solids (TSS), and oil and grease) from olive oil mill processing wastewater by peroxi-electrocoagulation/electrooxidation-electroflotation process with bipolar aluminum electrodes was evaluated using a pilot continuous reactor. In the electrochemical unit, aluminum (Al), stainless steel, and RuO2/Ti plates were used. The effects of pH, hydrogen peroxide doses, current density, NaCl concentrations, and reaction times were studied. Under optimal conditions of pH 4, current density of 40 mA/m(2), 1000 mg/L H2O2, 1 g/L NaCl, and 30-min reaction time, the peroxi-electrochemical method yielded very effective removal of organic pollution from the olive mill wastewater diluted four times. The treatment process reduced COD by 96%, BOD5 by 93.6%, total, polyphenols by 94.4%, color by 91.4%, turbidity by 88.7, suspended solids by 97% and oil and grease by 97.1%. The biodegradability index (BOD5/COD) increased from 0.29 to 0.46. Therefore, the peroxi-electrocoagulation/electrooxidation-electroflotation process is considered as an effective and feasible process for pre-treating olive mill wastewater, making possible a post-treatment of the effluent in a biological system.

Effects of three types of oil dispersants on biodegradation of dispersed crude oil in water surrounding two Persian gulf provinces.

Science.gov (United States)

Zolfaghari-Baghbaderani, Azadeh; Emtyazjoo, Mozhgan; Poursafa, Parinaz; Mehrabian, Sedigheh; Bijani, Samira; Farkhani, Daryoush; Mirmoghtadaee, Parisa

2012-01-01

To determine the most effective and biodegradable dispersant of spilled oil in water surrounding two Persian Gulf provinces. This study compared the effects of three dispersants, Pars 1, Pars 2, and Gamlen OD4000 on removal of oil in two Persian Gulf provinces' water. Overall, 16 stations were selected. Using the Well method, the growth rate of isolated bacteria and fungi was identified. To specify the growth rate of microorganisms and their usage of oil in the presence of the above-mentioned dispersants, as exclusive sources of carbon, the bacteria were grown in culture medium for 28 days at 120 rpm, 30°C, and their optical density was measured by spectrophotometry. Then, we tested biological oxygen demand (BOD) and chemical oxygen demand (COD) in microorganisms. The highest growth rate was documented for the growth of microorganisms on either Pars 1 or Pars 2 dispersants or their mixtures with oil. However, the culture having microorganisms grown on Pars 1 had higher BOD and COD than the other two dispersants (9200 and 16800 versus 500 and 960, P microorganisms grown on Pars 2 had maximum amount of BOD and COD in comparison with Pars 1 and Gamlen dispersants (7100 and 15200 versus 6000 and 10560, P < 0.05). Pars 1 and Pars 2 were the most effective dispersants with highest degradability comparing Gamlen. In each region, the most suitable compound for removing oil spill from offshores with least secondary contamination should be investigated.

Soil aquifer treatment of artificial wastewater under saturated conditions

KAUST Repository

Essandoh, H. M K

2011-05-01

A 2000 mm long saturated laboratory soil column was used to simulate soil aquifer treatment under saturated conditions to assess the removal of chemical and biochemical oxygen demand (COD and BOD), dissolved organic carbon (DOC), nitrogen and phosphate, using high strength artificial wastewater. The removal rates were determined under a combination of constant hydraulic loading rates (HLR) and variable COD concentrations as well as variable HLR under a constant COD. Within the range of COD concentrations considered (42 mg L-1-135 mg L-1) it was found that at fixed hydraulic loading rate, a decrease in the influent concentrations of dissolved organic carbon (DOC), biochemical oxygen demand (BOD), total nitrogen and phosphate improved their removal efficiencies. At the high COD concentrations applied residence times influenced the redox conditions in the soil column. Long residence times were detrimental to the removal process for COD, BOD and DOC as anoxic processes and sulphate reduction played an important role as electron acceptors. It was found that total COD mass loading within the range of 911 mg d-1-1780 mg d-1 applied as low COD wastewater infiltrated coupled with short residence times would provide better effluent quality than the same mass applied as a COD with higher concentration at long residence times. The opposite was true for organic nitrogen where relatively high concentrations coupled with long residence time gave better removal efficiency. © 2011.

Anaerobic/aerobic treatment of greywater via UASB and MBR for unrestricted reuse.

Science.gov (United States)

Abdel-Shafy, Hussein I; Al-Sulaiman, Ahmed Makki; Mansour, Mona S M

2015-01-01

The aim of the present study was to investigate the efficiency of integrated up-flow anaerobic sludge blanket (UASB) as anaerobic system followed by membrane bioreactor (MBR) as aerobic system for the treatment of greywater for unrestricted reuse. Pilot-scale UASB and MBR units were installed and operated in the NRC, Egypt. Real raw greywater was subjected to UASB and the effluent was further treated with microfiltration MBR. The necessary trans-membrane pressure difference is applied by the water head above the membrane (gravity flow) without any energy input. The average characteristics of the raw greywater were 95, 392, 298, 10.45, 0.4, 118.5 and 28 mg/L for total suspended solids (TSS), chemical oxygen demand (COD), biochemical oxygen demand (BOD), total phosphates, nitrates, oil and grease, and total Kjeldahl nitrogen (TKN), respectively. The pH was 6.71. The UASB treatment efficiency reached 19.3, 57.8, 67.5 and 83.7% for TSS, COD, BOD5 and oil and grease, respectively. When the UASB effluent was further treated with MBR, the overall removal rate achieved 97.7, 97.8, 97.4 and 95.8% for the same parameters successively. The characteristics of the final effluent reached 2.5, 8.5, 6.1, 0.95, 4.6 and 2.3 mg/L for TSS, COD, BOD, phosphates, oil and grease and TKN, respectively. This final treated effluent could cope with the unrestricted water reuse of local Egyptian guidelines.

Physico-chemical, microbiological and ecotoxicological evaluation of a septic tank/Fenton reaction combination for the treatment of hospital wastewaters.

Science.gov (United States)

Berto, Josiani; Rochenbach, Gisele Canan; Barreiros, Marco Antonio B; Corrêa, Albertina X R; Peluso-Silva, Sandra; Radetski, Claudemir Marcos

2009-05-01

Hospital wastewater is considered a complex mixture populated with pathogenic microorganisms. The genetic constitution of these microorganisms can be changed through the direct and indirect effects of hospital wastewater constituents, leading to the appearance of antibiotic multi-resistant bacteria. To avoid environmental contamination hospital wastewaters must be treated. The objective of this study was to evaluate the efficiency of hospital wastewater treated by a combined process of biological degradation (septic tank) and the Fenton reaction. Thus, after septic tank biodegradation, batch Fenton reaction experiments were performed in a laboratory-scale reactor and the effectiveness of this sequential treatment was evaluated by a physico-chemical/microbiological time-course analysis of COD, BOD(5), and thermotolerant and total coliforms. The results showed that after 120min of Fenton treatment BOD(5) and COD values decreased by 90.6% and 91.0%, respectively. The BOD(5)/COD ratio changed from 0.46 to 0.48 after 120min of treatment. Bacterial removal efficiency reached 100%, while biotests carried out with Scenedesmus subspicatus and Daphnia magna showed a significant decrease in the ecotoxicity of hospital wastewater after the sequential treatment. The use of this combined system would ensure that neither multi-resistant bacteria nor ecotoxic substances are released to the environment through hospital wastewater discharge.

Quantum dots assisted photocatalysis for the chemiluminometric determination of chemical oxygen demand using a single interface flow system

Energy Technology Data Exchange (ETDEWEB)

Silvestre, Cristina I.C.; Frigerio, Christian [Requimte, Department of Chemistry, Faculty of Pharmacy, Porto University, Rua Anibal Cunha 164, 4099-030, Porto (Portugal); Santos, Joao L.M., E-mail: joaolms@ff.up.pt [Requimte, Department of Chemistry, Faculty of Pharmacy, Porto University, Rua Anibal Cunha 164, 4099-030, Porto (Portugal); Lima, Jose L.F.C. [Requimte, Department of Chemistry, Faculty of Pharmacy, Porto University, Rua Anibal Cunha 164, 4099-030, Porto (Portugal)

2011-08-12

Highlights: {yields} A novel flow method for the determination of chemical oxygen demand is proposed. {yields} CdTe nanocrystals are irradiated with UV light to generate strong oxidizing species. {yields} Reactive species promote a fast catalytic degradation of organic matter. {yields} Luminol is used as a chemiluminescence probe for indirect COD assessment. {yields} A single interface flow system was implemented to automate the assays. - Abstract: A novel flow method for the determination of chemical oxygen demand (COD) is proposed in this work. It relies on the combination of a fully automated single interface flow system, an on-line UV photocatalytic unit and quantum dot (QD) nanotechnology. The developed approach takes advantage of CdTe nanocrystals capacity to generate strong oxidizing species upon irradiation with UV light, which fostered a fast catalytic degradation of the organic compounds. Luminol was used as a chemiluminescence (CL) probe for indirect COD assessment, since it is easily oxidized by the QD generated species yielding a strong CL emission that is quenched in the presence of the organic matter. The proposed methodology allowed the determination of COD concentrations between 1 and 35 mg L{sup -1}, with good precision (R.S.D. < 1.1%, n = 3) and a sampling frequency of about 33 h{sup -1}. The procedure was applied to the determination of COD in wastewater certified reference materials and the obtained results showed an excellent agreement with the certified values.

Efeito da concentração inicial de oxigênio no coeficiente de aeração para experimentos de DBO de longo prazo - DOI: 10.4025/actascibiolsci.v25i2.1976 Effect of initial concentration of dissolved oxygen in aeration coefficient for long-term BOD experiments- DOI: 10.4025/actascibiolsci.v25i2.1976

Directory of Open Access Journals (Sweden)

Marcela Bianchessi da Cunha Santino

2003-04-01

Full Text Available Incubações de demanda bioquímica de oxigênio (DBO de longo prazo foram realizadas para determinar o coeficiente de aeração proveniente de experimentos de consumo de oxigênio. Os frascos de DBO foram preparados com água destilada e incubados no escuro e sob temperatura controlada (19,4ºC. Os frascos foram submetidos a dois tratamentos que foram baseados na concentração inicial de oxigênio dissolvido (OD: Tratamento 1 = 1,43mg L-1 e Tratamento 2 = 7,67mg L-1. As concentrações de OD foram determinadas com oxímetro durante 52 dias. Os resultados foram ajustados a um modelo cinético de primeira ordem. Os frascos de DBO apresentaram um incremento nas concentrações de OD para ambos os tratamentos e o coeficiente de aeração (ka foi de 0,065 dia-1. Os ajustes apontam dispersão nos valores de ka e a concentração inicial de OD nos frascos de DBO não interferiu no processo de aeração sendo um processo aleatórioLong-term incubations of biochemical oxygen demand (BOD were performed to determine the aeration coefficient derived from oxygen uptake experiments. The BOD bottles were prepared with distilled water and the incubation occurred in the dark, under controlled temperature (19.4ºC. The bottles were submitted to two different treatments based on the initial dissolved oxygen (DO concentrations (Treatment 1: 1.43mg L-1 and Treatment 2: 7.67mg L-1. The DO concentrations were measured with an OD meter during 52 days. The results were fitted to a first-order kinetics model. The BOD bottles showed an increase in DO concentration for both treatments and the mean aeration coefficient (ka was 0.065 a day-1. The fittings pointed to some dispersion in the ka values, and the initial concentration of DO in the BOD bottles does not interfere in the aeration process, being a random process

Chemometrics-assisted spectrophotometry method for the determination of chemical oxygen demand in pulping effluent.

Science.gov (United States)

Chen, Honglei; Chen, Yuancai; Zhan, Huaiyu; Fu, Shiyu

2011-04-01

A new method has been developed for the determination of chemical oxygen demand (COD) in pulping effluent using chemometrics-assisted spectrophotometry. Two calibration models were established by inducing UV-visible spectroscopy (model 1) and derivative spectroscopy (model 2), combined with the chemometrics software Smica-P. Correlation coefficients of the two models are 0.9954 (model 1) and 0.9963 (model 2) when COD of samples is in the range of 0 to 405 mg/L. Sensitivities of the two models are 0.0061 (model 1) and 0.0056 (model 2) and method detection limits are 2.02-2.45 mg/L (model 1) and 2.13-2.51 mg/L (model 2). Validation experiment showed that the average standard deviation of model 2 was 1.11 and that of model 1 was 1.54. Similarly, average relative error of model 2 (4.25%) was lower than model 1 (5.00%), which indicated that the predictability of model 2 was better than that of model 1. Chemometrics-assisted spectrophotometry method did not need chemical reagents and digestion which were required in the conventional methods, and the testing time of the new method was significantly shorter than the conventional ones. The proposed method can be used to measure COD in pulping effluent as an environmentally friendly approach with satisfactory results.

CHEMICAL INTERACTIONS TO CLEANUP HIGHLY POLLUTED AUTOMOBILE SERVICE STATION WASTEWATER BY BIOADSORPTION-COAGULATION-FLOCCULATION

Directory of Open Access Journals (Sweden)

Carlos Banchon

2017-01-01

Full Text Available The present study addresses an ecofriendly solution to treat automobile service stations effluents with high concentrations of oily substances, surfactants, organic matter and heavy metals. Bioadsorption using sawdust from pine trees, sugar cane bagasse and coconut coir without any chemical modification removed colloidal contamination up to 70%. Polyaluminium chloride, ferric chloride and polyacrylamide were applied to remove dissolved and colloidal pollutants under saline conditions without change of initial pH. Both bioadsorption and coagulation-flocculation removed up to 97.8% of BOD, COD, surfactants and heavy metals at a saline concentration of 1.5% NaCl. The increase of ionic strength promoted a high sludge index and a representative cost saving in chemicals consumption of almost 70%. High levels of pollution removal with the minimal use of chemicals is herein presented.

A combined electrocoagulation-sorption process applied to mixed industrial wastewater

Energy Technology Data Exchange (ETDEWEB)

Linares-Hernandez, Ivonne [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon interseccion Paseo Tollocan S/N, C.P. 50120, Toluca (Mexico); Barrera-Diaz, Carlos [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon interseccion Paseo Tollocan S/N, C.P. 50120, Toluca (Mexico)]. E-mail: cbarrera@uaemex.mx; Roa-Morales, Gabriela [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon interseccion Paseo Tollocan S/N, C.P. 50120, Toluca (Mexico); Bilyeu, Bryan [University of North Texas, Department of Materials Science and Engineering, PO Box 305310, Denton, TX 76203-5310 (United States); Urena-Nunez, Fernando [Instituto Nacional de Investigaciones Nucleares, A.P. 18-1027, Col. Escandon, Delegacion Miguel Hidalgo, C.P. 11801, Mexico, D.F. (Mexico)

2007-06-01

The removal of organic pollutants from a highly complex industrial wastewater by a aluminium electrocoagulation process coupled with biosorption was evaluated. Under optimal conditions of pH 8 and 45.45 A m{sup -2} current density, the electrochemical method yields a very effective reduction of all organic pollutants, this reduction was enhanced when the biosorption treatment was applied as a polishing step. Treatment reduced chemical oxygen demand (COD) by 84%, biochemical oxygen demand (BOD{sub 5}) by 78%, color by 97%, turbidity by 98% and fecal coliforms by 99%. The chemical species formed in aqueous solution were determined. The initial and final pollutant levels in the wastewater were monitored using UV-vis spectrometry and cyclic voltammetry. Finally, the morphology and elemental composition of the biosorbent was characterized with scanning electron microscopy (SEM) and energy dispersion spectra (EDS)

Water

Directory of Open Access Journals (Sweden)

E. Sanmuga Priya

2017-05-01

Full Text Available Phytoremediation through aquatic macrophytes treatment system (AMATS for the removal of pollutants and contaminants from various natural sources is a well established environmental protection technique. Water hyacinth (Eichhornia crassipes, a worst invasive aquatic weed has been utilised for various research activities over the last few decades. The biosorption capacity of the water hyacinth in minimising various contaminants present in the industrial wastewater is well studied. The present review quotes the literatures related to the biosorption capacity of the water hyacinth in reducing the concentration of dyestuffs, heavy metals and minimising certain other physiochemical parameters like TSS (total suspended solids, TDS (total dissolved solids, COD (chemical oxygen demand and BOD (biological oxygen demand in textile wastewater. Sorption kinetics through various models, factors influencing the biosorption capacity, and role of physical and chemical modifications in the water hyacinth are also discussed.

Green Walls as an Approach in Grey Water Treatment

Science.gov (United States)

Rysulova, Martina; Kaposztasova, Daniela; Vranayova, Zuzana

2017-10-01

Grey water contributes significantly to waste water parameters such as biochemical oxygen demand (BOD), chemical oxygen demand (COD), total suspended solids (TSS), total phosphorus (Ptotal), total nitrogen (Ntotal), ammonium, boron, metals, salts, surfactants, synthetic chemicals, oils and greases, xenobiotic substances and microorganisms. Concentration of these pollutants and the water quality highlights the importance of treatment process in grey water systems. Treatment technologies operating under low energy and maintenance are usually preferred, since they are more cost effective for users. Treatment technologies based on natural processes represent an example of such technology including vegetated wall. Main aim of this paper is to introduce the proposal of vegetated wall managing grey water and brief characteristic of proposed system. Is expected that prepared experiment will establish the purifying ability and the potential of green wall application as an efficient treatment technology.

A combined electrocoagulation-sorption process applied to mixed industrial wastewater

International Nuclear Information System (INIS)

Linares-Hernandez, Ivonne; Barrera-Diaz, Carlos; Roa-Morales, Gabriela; Bilyeu, Bryan; Urena-Nunez, Fernando

2007-01-01

The removal of organic pollutants from a highly complex industrial wastewater by a aluminium electrocoagulation process coupled with biosorption was evaluated. Under optimal conditions of pH 8 and 45.45 A m -2 current density, the electrochemical method yields a very effective reduction of all organic pollutants, this reduction was enhanced when the biosorption treatment was applied as a polishing step. Treatment reduced chemical oxygen demand (COD) by 84%, biochemical oxygen demand (BOD 5 ) by 78%, color by 97%, turbidity by 98% and fecal coliforms by 99%. The chemical species formed in aqueous solution were determined. The initial and final pollutant levels in the wastewater were monitored using UV-vis spectrometry and cyclic voltammetry. Finally, the morphology and elemental composition of the biosorbent was characterized with scanning electron microscopy (SEM) and energy dispersion spectra (EDS)

Using remotely sensed imagery to estimate potential annual pollutant loads in river basins.

Science.gov (United States)

He, Bin; Oki, Kazuo; Wang, Yi; Oki, Taikan

2009-01-01

Land cover changes around river basins have caused serious environmental degradation in global surface water areas, in which the direct monitoring and numerical modeling is inherently difficult. Prediction of pollutant loads is therefore crucial to river environmental management under the impact of climate change and intensified human activities. This research analyzed the relationship between land cover types estimated from NOAA Advanced Very High Resolution Radiometer (AVHRR) imagery and the potential annual pollutant loads of river basins in Japan. Then an empirical approach, which estimates annual pollutant loads directly from satellite imagery and hydrological data, was investigated. Six water quality indicators were examined, including total nitrogen (TN), total phosphorus (TP), suspended sediment (SS), Biochemical Oxygen Demand (BOD), Chemical Oxygen Demand (COD), and Dissolved Oxygen (DO). The pollutant loads of TN, TP, SS, BOD, COD, and DO were then estimated for 30 river basins in Japan. Results show that the proposed simulation technique can be used to predict the pollutant loads of river basins in Japan. These results may be useful in establishing total maximum annual pollutant loads and developing best management strategies for surface water pollution at river basin scale.

Enhancement of Biodegradation of Palm Oil Mill Effluents by Local Isolated Microorganisms.

Science.gov (United States)

Soleimaninanadegani, Mohammadreza; Manshad, Soheila

2014-01-01

This study was designed to investigate the microorganisms associated with palm oil mill effluent (POME) in Johor Bahru state, Malaysia. Biodegradation of palm oil mill effluents (POME) was conducted to measure the discarded POME based on physicochemical quality. The bacteria that were isolated are Micrococcus species, Bacillus species, Pseudomonas species, and Staphylococcus aureus, while the fungi that were isolated are Aspergillus niger, Aspergillus fumigatus, Candida species, Fusarium species, Mucor species, and Penicillium species. The autoclaved and unautoclaved raw POME samples were incubated for 7 days and the activities of the microorganisms were observed each 12 hours. The supernatants of the digested POME were investigated for the removal of chemical oxygen demand (COD), color (ADMI), and biochemical oxygen demand (BOD) at the end of each digestion cycle. The results showed that the unautoclaved raw POME sample degraded better than the inoculated POME sample and this suggests that the microorganisms that are indigenous in the POME are more effective than the introduced microorganisms. This result, however, indicates the prospect of isolating indigenous microorganisms in the POME for effective biodegradation of POME. Moreover, the effective treatment of POME yields useful products such as reduction of BOD, COD, and color.

Alteration of Water Pollution Level with the Seasonal Changes in Mean Daily Discharge in Three Main Rivers around Dhaka City, Bangladesh

Directory of Open Access Journals (Sweden)

Md. Saiful Islam

2015-06-01

Full Text Available A study based on the physicochemical parameters and dissolved metals levels from three main rivers around Dhaka City, Bangladesh, was conducted in order to determine the present pollution status and their alteration trends with the seasonal change of discharge amount. The water samples were collected from the rivers Buriganga, Turag, and Shitalakkhya during both dry and monsoon seasons. Physicochemical analyses revealed that most of the water quality parameters exceeded the recommended levels set by the Department of Environment (DoE, Bangladesh, during both the dry and monsoon seasons. A very strong positive correlation was found between biochemical oxygen demand (BOD and chemical oxygen demand (COD in all sampling points. Both BOD and COD values had a strong negative correlation with dissolved oxygen (DO in the Shitalakkhya River. Most of the dissolved metals concentrations in the water samples were similar. However, the concentrations of different physicochemical properties varied with the seasons. The dry season had significantly higher contamination loads, which were decreased during the monsoon season. Anthropogenic activities, as well as the variation in river water flow during different seasons were the main reasons for this high degree of water pollution.

Treatment of oilfield produced water by anaerobic process coupled with micro-electrolysis.

Science.gov (United States)

Li, Gang; Guo, Shuhai; Li, Fengmei

2010-01-01

Treatment of oilfield produced water was investigated using an anaerobic process coupled with micro-electrolysis (ME), focusing on changes in chemical oxygen demand (COD) and biodegradability. Results showed that COD exhibited an abnormal change in the single anaerobic system in which it increased within the first 168 hr, but then decreased to 222 mg/L after 360 hr. The biological oxygen demand (five-day) (BODs)/COD ratio of the water increased from 0.05 to 0.15. Hydrocarbons in the wastewater, such as pectin, degraded to small molecules during the hydrolytic acidification process. Comparatively, the effect of ME was also investigated. The COD underwent a slight decrease and the BOD5/COD ratio of the water improved from 0.05 to 0.17 after ME. Removal of COD was 38.3% under the idealized ME conditions (pH 6.0), using iron and active carbon (80 and 40 g/L, respectively). Coupling the anaerobic process with ME accelerated the COD removal ratio (average removal was 53.3%). Gas chromatography/mass spectrometry was used to analyze organic species conversion. This integrated system appeared to be a useful option for the treatment of water produced in oilfields.

Enhancement of Biodegradation of Palm Oil Mill Effluents by Local Isolated Microorganisms

Science.gov (United States)

Soleimaninanadegani, Mohammadreza

2014-01-01

This study was designed to investigate the microorganisms associated with palm oil mill effluent (POME) in Johor Bahru state, Malaysia. Biodegradation of palm oil mill effluents (POME) was conducted to measure the discarded POME based on physicochemical quality. The bacteria that were isolated are Micrococcus species, Bacillus species, Pseudomonas species, and Staphylococcus aureus, while the fungi that were isolated are Aspergillus niger, Aspergillus fumigatus, Candida species, Fusarium species, Mucor species, and Penicillium species. The autoclaved and unautoclaved raw POME samples were incubated for 7 days and the activities of the microorganisms were observed each 12 hours. The supernatants of the digested POME were investigated for the removal of chemical oxygen demand (COD), color (ADMI), and biochemical oxygen demand (BOD) at the end of each digestion cycle. The results showed that the unautoclaved raw POME sample degraded better than the inoculated POME sample and this suggests that the microorganisms that are indigenous in the POME are more effective than the introduced microorganisms. This result, however, indicates the prospect of isolating indigenous microorganisms in the POME for effective biodegradation of POME. Moreover, the effective treatment of POME yields useful products such as reduction of BOD, COD, and color. PMID:27433516

Performance of A Pilot-Scale Vermifilter for the Treatment of A Real Hospital Wastewater

Directory of Open Access Journals (Sweden)

Nahid Ghobadi

2016-12-01

Full Text Available In this study, the performance of a pilot-scale vermifilter (VF for the treatment of hospital wastewater using the earthworm species Eisenia fetida was evaluated. The earthworms’ gut acts as a bioreactor and can ingest the wastewater solid and liquid organic wastes and expel these as vermicompost. A pilot-scale vermifilter was installed and operated for 133 days in one of hospitals in Hamadan city; the designed system was fed with the influent passed through coarse and fine grillage and the sedimentation tank of the hospital’s sanitary collection system. In order to study the efficiency of the system, the variations of pH value, chemical oxygen demand (COD, biochemical oxygen demand (BOD5, and total suspended solids (TSS were measured. In addition, a conventional geofilter (GF without Earthworm was used as the experimental control. The vermifiltration caused a significant decrease in the levels of COD (75%, BOD5 (93%, and TSS (89% as well as neutralized pH in the wastewater. Also, these contents in the geofilter were observed to be 65%, 71%, and 71%, respectively. The vermifiltration technology can, therefore, be applied as an environmentally friendly method for hospital wastewater treatment.

Monitoring of impact of anthropogenic inputs on water quality of mangrove ecosystem of Uran, Navi Mumbai, west coast of India.

Science.gov (United States)

Pawar, Prabhakar R

2013-10-15

Surface water samples were collected from substations along Sheva creek and Dharamtar creek mangrove ecosystems of Uran (Raigad), Navi Mumbai, west coast of India. Water samples were collected fortnightly from April 2009 to March 2011 during spring low and high tides and were analyzed for pH, Temperature, Turbidity, Total solids (TS), Total dissolved solids (TDS), Total suspended solids (TSS), Dissolved oxygen (DO), Biochemical oxygen demand (BOD), Carbon dioxide (CO2), Chemical oxygen demand (COD), Salinity, Orthophosphate (O-PO4), Nitrite-nitrogen (NO2-N), Nitrate-nitrogen (NO3-N), and Silicates. Variables like pH, turbidity, TDS, salinity, DO, and BOD show seasonal variations. Higher content of O-PO4, NO3-N, and silicates is recorded due to discharge of domestic wastes and sewage, effluents from industries, oil tanking depots and also from maritime activities of Jawaharlal Nehru Port Trust (JNPT), hectic activities of Container Freight Stations (CFS), and other port wastes. This study reveals that water quality from mangrove ecosystems of Uran is deteriorating due to industrial pollution and that mangrove from Uran is facing the threat due to anthropogenic stress. Copyright © 2013 Elsevier Ltd. All rights reserved.

Environmental Parameters Affecting the Algal Diversity in a Sewage Water Treatment Plant

International Nuclear Information System (INIS)

Hammad, D.M.; Tawfik, T.A.; Ismail, G.A.; Abou El-Khair, W.S.; Abou El-Nour, F.

2008-01-01

The present investigation was carried out at a tertiary sewage water treatment plant located at El-Kattameya city, Cairo, Egypt, for a duration period of 12 months during 2004. The present work aimed to study the algal diversity (phyto benthos and phytoplankton) of the different tanks (collector, oxidation, settling and effluent) included in the tertiary sewage treatment system with respect to changes in physico-chemical characteristics of sewage water during the different seasons to be used for golf course irrigation. The treatment system is of the physico-biological type. Representing data of the physico-chemical parameters are air and water temperatures, ph, electrical conductivity (EC), dissolved oxygen (DO), chemical oxygen demand (COD), biological oxygen demand (BOD), total suspended salts (TSS), total alkalinity, nutrients (nitrate, ammonia, phosphate, ortho-phosphorus, phosphorus and silicate), as well as major ions (calcium, potassium, sodium, magnesium, sulfate and chloride). In addition, the treatment efficiency of the system was evaluated and the suitability of using the effluent in irrigation purposes was discussed

Chemical Oxygen Demand abatement in sewage using Micro-Aeration Enhanced Ecological Floating Bed

Science.gov (United States)

Shi, Hongle; Zhou, Gaofeng; Liu, Yiqing; Tan, Jiancong; Fu, Yongsheng

2018-02-01

The traditional ecological floating bed combined with micro-aeration system and artificial medium was developed for the removal of contaminants and remediation of surface water. This micro-aeration enhanced ecological floating bed (MAEEFB) consisted of aeration unit, microbial processing unit and aquatic plant unit. Batch experiments were conducted in different operating conditions on the removal of chemical oxygen demand (COD) in the sewage using MAEEFB. The removal rate of COD by MAEEFB, enhanced ecological floating bed (EEFB) and traditional ecological floating bed (TEFB) in the same reaction conditions was 59.2%, 56.9% and 30.6%, respectively, indicating that the combination of micro-aeration system and artificial medium could enhance the removal efficiency of COD in TEFB. In MAEEFB, the aeration intensity should be designed reasonablely considering both treatment efficiency and operation cost. Only increasing the specific surface area of the packing cannot effectively improve the purification efficiency of water. Factors like packing material, ability of intercepting organics and complicated extent of microorganisms attaching on the packing should also be considered.

Bioremediation of Synthetic and Industrial Effluents by Aspergillus niger Isolated from Contaminated Soil Following a Sequential Strategy.

Science.gov (United States)

Gulzar, Tahsin; Huma, Tayyaba; Jalal, Fatima; Iqbal, Sarosh; Abrar, Shazia; Kiran, Shumaila; Nosheen, Sofia; Hussain, Waqar; Rafique, Muhammad Asim

2017-12-16

The present study aimed to assess and compare the ability to remediate synthetic textile and industrial wastewaters by Fenton treatment, a biological system and sequential treatments using Aspergillus niger ( A. niger ). All studied treatments were found to be effective in decolorization of the effluents under study. Fenton treatment followed by A. niger showed excellent potential for the maximum decolorization of the synthetic and industrial effluents under study. The effectiveness of sequential treatment was evaluated by water quality parameters such as total organic carbon (TOC), Biological Oxygen Demand (BOD5) and Chemical Oxygen Demand (COD) before and after each treatment. The results indicated that A. niger is an effective candidate for detoxification of textile wastewaters.

Bioremediation of Synthetic and Industrial Effluents by Aspergillus niger Isolated from Contaminated Soil Following a Sequential Strategy

Directory of Open Access Journals (Sweden)

Tahsin Gulzar

2017-12-01

Full Text Available The present study aimed to assess and compare the ability to remediate synthetic textile and industrial wastewaters by Fenton treatment, a biological system and sequential treatments using Aspergillus niger (A. niger. All studied treatments were found to be effective in decolorization of the effluents under study. Fenton treatment followed by A. niger showed excellent potential for the maximum decolorization of the synthetic and industrial effluents under study. The effectiveness of sequential treatment was evaluated by water quality parameters such as total organic carbon (TOC, Biological Oxygen Demand (BOD5 and Chemical Oxygen Demand (COD before and after each treatment. The results indicated that A. niger is an effective candidate for detoxification of textile wastewaters.

A simple biofilter for treatment of pig slurry in Malaysia.

Science.gov (United States)

Sommer, S G; Mathanpaal, G; Dass, G T

2005-03-01

On commercial pig production farms in South East (SE) Asia, the liquid effluent is often discharged into rivers. The discharge is a hazard to the environment and to the health of people using water from the river either for consumption or for irrigation. Therefore, a simple percolation biofilter for treatment of the liquid effluent was developed. Pig slurry was treated in test-biofilters packed with different biomass for the purpose of selecting the most efficient material, thereafter the efficiency of the biofilter was examined at farm scale with demo biofilters using the most efficient material. The effect of using "Effective Microorganisms" (EM) added to slurry that was treated with biofilter material mixed with Glenor KR+ was examined. Slurry treatment in the test-biofilters indicated that rice straw was better than coconut husks, wood shavings, rattan strips and oil palm fronds in reducing BOD. Addition of EM and Glenor KR+ to slurry and biofilter material, respectively, had no effect on the temperature of the biofilter material or on the concentrations of organic and inorganic components of the treated slurry. The BOD of slurry treated in test biofilters is reduced to between 80 and 637 mg O2 I(-1) and in the demo biofilter to between 3094 and 3376 mg O2 l(-1). The concentration of BOD in the effluent is related to the BOD in the slurry being treated and the BOD concentration in slurry treated in test biofilters was lower than BOD of slurry treated in demo biofilters. The demo biofilter can reduce BOD to between 52 an 56% of the original value, and TSS, COD (chemical oxygen demand) and ammonium (NH4+) to 41-55% of the original slurry. The treated effluent could not meet the standards for discharge to rivers. The composted biofilter material has a high content of nitrogen and phosphorus; consequently, the fertilizer value of the compost is high. The investments costs were 123 US dollar per SPP which has to be reduced if this method should be a treatment option

Drawer compacted sand filter: a new and innovative method for on-site grey water treatment.

Science.gov (United States)

Assayed, Almoayied; Chenoweth, Jonathan; Pedley, Steven

2014-01-01

In this paper, results ofa new sand filter design were presented. The drawer compacted sand filter (DCSF) is a modified design for a sand filter in which the sand layer is broken down into several layers, each of which is 10 cm high and placed in a movable drawer separated by a 10 cm space. A lab-scale DCSF was designed and operated for 330 days fed by synthetic grey water. The response of drawer sand filters to variable hydraulic and organic loading rates (HLR and OLR) in terms of biological oxygen demand (BODs), chemical oxygen demand (COD), total suspended solids (TSS), pH, electrical conductivity and Escherichia coli reductions were evaluated. The HLR was studied by increasing from 72 to 142 L m(-2) day(-1) and OLR was studied by increasing it from 23 to 30 g BOD5 m(-2) day(-1) while keeping the HLR constant at 142 L m(-2) day(-1). Each loading regime was applied for 110 days. Results showed that DCSF was able to remove >90% of organic matter and total suspended solids for all doses. No significant difference was noticed in terms of overall filter efficiency between different loads for all parameters. Significant reduction in BOD5 and COD (P water was drained through the third drawer in all tested loads. The paper concludes that DCSF would be appropriate for use in dense urban areas as its footprint is small and is appropriate for a wide range of users because of its convenience and low maintenance requirements.

Mineral and organic compounds in leachate from landfill with concentrate recirculation.

Science.gov (United States)

Talalaj, Izabela Anna

2015-02-01

The effect of a reverse osmosis concentrate recirculation on the mineral and organic compounds in a landfill leachate was investigated. Investigated was the quality of a leachate from two landfills operated for different periods (a 20-year-old Cell A and a 1-year-old Cell B), where the concentrate was recirculated. Examined were general parameters (conductivity, pH), organic compounds (biochemical oxygen demand (BOD), chemical oxygen demand (COD), total organic nitrogen, BOD/COD), and inorganic compounds (nitrogen ammonia, sulfite, sulfate, cyanide, boron, chloride, ferrous, zinc, chrome, copper). The findings from the first year of investigation showed that over the initial period of recirculation, the concentration of organic compounds (BOD, COD) increased, but after 6 months their values stabilized. It indicates that the concentrate recirculation accelerated organic decomposition, especially in the new landfill Cell. The analysis of inorganic parameters showed that recirculation landfills produce a leachate with a higher concentration of N-NH4, and Cl(-). In case of the old landfill Cell, an increase in B and Fe was also noticeable. These compounds are cyclically washed out from a waste dump and require an additional pretreatment in order to exclude them from recirculation cycle. The increased concentration of Cu, Zn, and Fe was noticed during the initial months of recirculation and in the season of intense atmospheric precipitation in the leachate from both Cells. Higher values of electro conductivity, Cl(-), N-NH4 (+), B, and Fe in the leachate from the old field indicate that the attenuation capacity of this landfill is close to exhaustion.

Recycling of canteen waste water for irrigation purpose

International Nuclear Information System (INIS)

Ahmad, J.

2005-01-01

Recycling of wastewater of a canteen was done at Attock refinery Limited, Rawalpindi during 2002. The wastewater of the refinery canteen was recycled after a long process and was reused for irrigation of nearby garden and other landscape plants. The average outflow of the wastewater from the canteen was calculated as 4000 liters/day. Laboratory analysis for the quality of wastewater was conducted and it was found that suspended solid. Chemical Oxygen demand (COD) and biochemical oxygen demand (BOD) of the wastewater were above the National Environmental Quality Standards (NEQS) limits. Treatment system employed was composed of screening and settling tank for removing the suspended solids and aeration for decreasing the COD and BOD. It was a low cost system in which the materials used were mostly taken from the redundant stock. Air was given for aeration with the help of a compressor. The treated water was tested in the laboratory for the priority parameters i.e. temperature, pH, BOD, COD, Total suspended solids (TSS), Total dissolved (TDS), oil and grease and Phenols. These parameters were compared with the National Environmental Quality Standards (NEQS). Treated water was used for irrigation of the nearby garden and landscape. The recycling process was successfully conducted and a huge quantity of 4000 liters water/day (1000 G water/day) was processes was successfully conducted and a huge quantity of 4000 liters water/day (1000 G water/day) was recycled with a daily saving of Rs.100 at the rate of Rs.1/10 G water that was taken from market survey. (author)

Characterization of Wastewaters obtained from Hatay Tanneries

Directory of Open Access Journals (Sweden)

Şana Sungur

2017-06-01

Full Text Available The leather tanning industry is one of the most significant pollutants in terms of both conventional and toxic parameters. On the other hand, leather industry has an important economic role both in Turkey and in the World. In this study, wastewater samples were taken from 15 different tanneries in the Hatay Region. Wastewaters obtained from liming process and chromium tanning process was analyzed. Sulfide, chromium (III, chromium (VI, oil and grease, total suspended solids (TSS, organic matters, biochemical oxygen demand (BOD, chemical oxygen demand (COD, pH and alkalinity were determined according to Turkish Standard Methods. The determined averages values belong to wastewaters obtained from liming process were as following: pH 11.71; COD 16821 mg L-1; BOD 4357 mg L-1; TSS 39023 mg L-1; oil and grease 364 mg L-1; S-2 concentration 802 mg L-1; alkalinity 2115 mg L-1. The determined averages values belong to wastewaters obtained from chromium tanning process were also as following: pH 4.23; COD 6740 mg L-1; BOD 377 mg L-1; Cr+3 concentrations 372 mg L-1; Cr+6 concentrations 127 mg L-1; TSS 14553 mg L-1; oil and grease 343 mg L-1. The results of all analyzes were higher than wastewater discharge standards. As a result, it’s necessary to use more effective treatments in order to reduce the negative impacts of leather tanning industry that affect environment, natural water resources and at last human health and welfare.

Performance of hybrid subsurface constructed wetland system for piggery wastewater treatment.

Science.gov (United States)

Zhang, X; Inoue, T; Kato, K; Harada, J; Izumoto, H; Wu, D; Sakuragi, H; Ietsugu, H; Sugawara, Y

2016-01-01

The objective of this study was to evaluate performance of a hybrid constructed wetland (CW) built for high organic content piggery wastewater treatment in a cold region. The system consists of four vertical and one horizontal flow subsurface CWs. The wetland was built in 2009 and water quality was monitored from the outset. Average purification efficiency of this system was 95±5, 91±7, 89±8, 70±10, 84±15, 90±6, 99±2, and 93±16% for biochemical oxygen demand (BOD5), chemical oxygen demand (COD), total carbon (TC), total nitrogen (TN), ammonium-N (NH4-N), total phosphorus (TP), total coliform (T. Coliform), and suspended solids (SS), respectively during August 2010-December 2013. Pollutant removal rate was 15±18 g m(-2) d(-1), 49±52 g m(-2) d(-1), 6±4 g m(-2) d(-1), 7±5 g m(-2) d(-1), and 1±1 g m(-2) d(-1) for BOD5, COD, TN, NH4-N, and TP, respectively. The removal efficiency of BOD5, COD, NH4-N, and SS improved yearly since the start of operation. With respect to removal of TN and TP, efficiency improved in the first three years but slightly declined in the fourth year. The system performed well during both warm and cold periods, but was more efficient in the warm period. The nitrate increase may be attributed to a low C/N ratio, due to limited availability of carbon required for denitrification.

Advanced landfill leachate treatment using iron-carbon microelectrolysis- Fenton process: Process optimization and column experiments

International Nuclear Information System (INIS)

Wang, Liqun; Yang, Qi; Wang, Dongbo; Li, Xiaoming; Zeng, Guangming; Li, Zhijun; Deng, Yongchao; Liu, Jun; Yi, Kaixin

2016-01-01

Highlights: • Fe-C microelectrolysis-Fenton process is proposed to pretreat landfill leachate. • Operating variables are optimized by response surface methodology (RSM). • 3D-EEMs and MW distribution explain the mechanism of enhanced biodegradability. • Fixed-bed column experiments are performed at different flow rates. - Abstract: A novel hydrogen peroxide-enhanced iron-carbon (Fe-C) microelectrolysis reactor was proposed for the pretreatment of mature landfill leachate. This reactor, combining microelectrolysis with Fenton process, revealed high treatment efficiency. The operating variables, including Fe-C dosage, H_2O_2 concentration and initial pH, were optimized by the response surface methodology (RSM), regarding the chemical oxygen demand (COD) removal efficiency and biochemical oxygen demand: chemical oxygen demand (BOD_5/COD) as the responses. The highest COD removal (74.59%) and BOD_5/COD (0.50) was obtained at optimal conditions of Fe-C dosage 55.72 g/L, H_2O_2 concentration 12.32 mL/L and initial pH 3.12. Three-dimensional excitation and emission matrix (3D-EEM) fluorescence spectroscopy and molecular weight (MW) distribution demonstrated that high molecular weight fractions such as refractory fulvic-like substances in leachate were effectively destroyed during the combined processes, which should be attributed to the combination oxidative effect of microelectrolysis and Fenton. The fixed-bed column experiments were performed and the breakthrough curves at different flow rates were evaluated to determine the practical applicability of the combined process. All these results show that the hydrogen peroxide-enhanced iron-carbon (Fe-C) microelectrolysis reactor is a promising and efficient technology for the treatment of mature landfill leachate.

Advanced landfill leachate treatment using iron-carbon microelectrolysis- Fenton process: Process optimization and column experiments

Energy Technology Data Exchange (ETDEWEB)

Wang, Liqun, E-mail: 691127317@qq.com [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Yang, Qi, E-mail: yangqi@hnu.edu.cn [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Wang, Dongbo [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Li, Xiaoming, E-mail: xmli121x@hotmail.com [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China); Zeng, Guangming; Li, Zhijun; Deng, Yongchao; Liu, Jun; Yi, Kaixin [College of Environmental Science and Engineering, Hunan University, Changsha 410082 (China); Key Laboratory of Environmental Biology and Pollution Control (Hunan University), Ministry of Education, Changsha 410082 (China)

2016-11-15

Highlights: • Fe-C microelectrolysis-Fenton process is proposed to pretreat landfill leachate. • Operating variables are optimized by response surface methodology (RSM). • 3D-EEMs and MW distribution explain the mechanism of enhanced biodegradability. • Fixed-bed column experiments are performed at different flow rates. - Abstract: A novel hydrogen peroxide-enhanced iron-carbon (Fe-C) microelectrolysis reactor was proposed for the pretreatment of mature landfill leachate. This reactor, combining microelectrolysis with Fenton process, revealed high treatment efficiency. The operating variables, including Fe-C dosage, H{sub 2}O{sub 2} concentration and initial pH, were optimized by the response surface methodology (RSM), regarding the chemical oxygen demand (COD) removal efficiency and biochemical oxygen demand: chemical oxygen demand (BOD{sub 5}/COD) as the responses. The highest COD removal (74.59%) and BOD{sub 5}/COD (0.50) was obtained at optimal conditions of Fe-C dosage 55.72 g/L, H{sub 2}O{sub 2} concentration 12.32 mL/L and initial pH 3.12. Three-dimensional excitation and emission matrix (3D-EEM) fluorescence spectroscopy and molecular weight (MW) distribution demonstrated that high molecular weight fractions such as refractory fulvic-like substances in leachate were effectively destroyed during the combined processes, which should be attributed to the combination oxidative effect of microelectrolysis and Fenton. The fixed-bed column experiments were performed and the breakthrough curves at different flow rates were evaluated to determine the practical applicability of the combined process. All these results show that the hydrogen peroxide-enhanced iron-carbon (Fe-C) microelectrolysis reactor is a promising and efficient technology for the treatment of mature landfill leachate.

What is the Effect of Case-Based Learning on the Academic Achievement of Students on the Topic of "Biochemical Oxygen Demand?"

Science.gov (United States)

Günter, Tuğçe; Alpat, Sibel Kılınç

2017-11-01

The purpose of this study was to investigate the effect of the case-based learning (CBL) method used in "biochemical oxygen demand (BOD)," which is a topic taught in the environmental chemistry course, at Dokuz Eylul University, on the academic achievement and opinions of students. The research had a quasi-experimental design and the study group consisted of 4th and 5th grade students (N = 18) attending the Chemistry Teaching Program in a university in Izmir. The "Biochemical Oxygen Demand Achievement Test (BODAT)" and the structured interview form were used as data collection tools. The results of BODAT post-test showed the higher increase in the achievement scores of the experimental group may be an indication of the effectiveness of the CBL method in improving academic achievement in the relevant topic. In addition, the experimental and control group students had positive opinions regarding the method, the scenario, and the material. The students found the method, the scenario, and the material to be interesting, understandable/instructional, relatable with everyday life, suitable for the topic, and enhancing active participation.

Physico-chemical characterization of grease interceptors with and without biological product addition.

Science.gov (United States)

He, Xia; Osborne, Jason; de los Reyes, Francis L

2012-03-01

Hardened and insoluble fat, oil, and grease (FOG) deposits are the primary cause of sewer line blockages leading to sanitary sewer overflows (SSOs). However, there have been very few long-term assessments of the physico-chemical characteristics of full-scale grease interceptors (GIs), the first "line of defense" against FOG buildup in sewer lines. In this study, we assessed the physico-chemical characteristics of two full-scale GIs (at a restaurant and a retirement community kitchen) over a one-year period. Statistically significant differences between bioaugmented and untreated cycles were detected for several chemical and physical properties. The treated cycles had lower BOD and COD at the grease interceptor outlet. While the combined data for all treated cycles did not show lower FOG concentrations in the GI outlet compared to the combined data for all untreated cycles, comparison of specific individual treated and untreated cycles show a positive effect due to the addition of product.

Dynamic of the structure and biodiversity of macrozoobenthos in one ...

African Journals Online (AJOL)

xiongjing

2012-07-10

Jul 10, 2012 ... oxygen demand; BOD, biochemical oxygen demand. cause a diverse range of .... deterministic factors determining the elimination or replacement of species .... need for new approaches and concepts. Glob. Change Biol.

Quality improvement in determination of chemical oxygen demand in samples considered difficult to analyze, through participation in proficiency-testing schemes

DEFF Research Database (Denmark)

Raposo, Francisco; Fernández-Cegrí, V.; De la Rubia, M.A.

2010-01-01

Chemical oxygen demand (COD) is a critical analytical parameter in waste and wastewater treatment, more specifically in anaerobic digestion, although little is known about the quality of measuring COD of anaerobic digestion samples. Proficiency testing (PT) is a powerful tool that can be used...... to test the performance achievable in the participants laboratories, so we carried out a second PT of COD determination in samples considered ‘‘difficult’’ to analyze (i.e. solid samples and liquid samples with high concentrations of suspended solids). The results obtained (based on acceptable z...

Electricity generation using white and red wine lees in air cathode microbial fuel cells

Science.gov (United States)

Pepe Sciarria, Tommy; Merlino, Giuseppe; Scaglia, Barbara; D'Epifanio, Alessandra; Mecheri, Barbara; Borin, Sara; Licoccia, Silvia; Adani, Fabrizio

2015-01-01

Microbial fuel cell (MFC) is a useful biotechnology to produce electrical energy from different organic substrates. This work reports for the first time results of the application of single chamber MFCs to generate electrical energy from diluted white wine (WWL) and red wine (RWL) lees. Power obtained was of 8.2 W m-3 (262 mW m-2; 500 Ω) and of 3.1 W m-3 (111 mW m-2; 500Ω) using white and red wine lees, respectively. Biological processes lead to a reduction of chemical oxygen (TCOD) and biological oxygen demand (BOD5) of 27% and 83% for RWL and of 90% and 95% for WWL, respectively. These results depended on the degradability of organic compounds contained, as suggest by BOD5/TCOD of WWL (0.93) vs BOD5/TCOD of RWL (0.33), and to the high presence of polyphenols in RWL that inhibited the process. Coulombic efficiency (CE) of 15 ± 0%, for WWL, was in line with those reported in the literature for other substrates, i.e. CE of 14.9 ± 11.3%. Different substrates led to different microbial consortia, particularly at the anode. Bacterial species responsible for the generation of electricity, were physically connected to the electrode, where the direct electron transfer took place.

Perbedaan Efektivitas Zeolit Dan Manganese Greensand Untuk Menurunkan Kadar Fosfat Dan Chemical Oxygen Demand Limbah Cair “Laundry Zone” Di Tembalang

OpenAIRE

Lavina, Dahona Lenthe; Sulistyani, Sulistyani; Rahadjo, Mursid

2016-01-01

Laundry business is a business in clothes washing services. Preliminary test results show that the levels of phosphate and COD laundry liquid wastes is 12,36 mg/l and 5.920 mg/l. These levels exceeded the water quality standard of waste that phosphate concentration of 2 mg/l and COD concentration of 100 mg/l. This research aimed to determine the difference effectiveness of zeolite and manganese greensand to decrease phosphate and chemical oxygen demand on waste "laundry zone" in Tembalang. T...

Slaughterhouse wastewater treatment by combined chemical coagulation and electrocoagulation process.

Science.gov (United States)

Bazrafshan, Edris; Kord Mostafapour, Ferdos; Farzadkia, Mehdi; Ownagh, Kamal Aldin; Mahvi, Amir Hossein

2012-01-01

Slaughterhouse wastewater contains various and high amounts of organic matter (e.g., proteins, blood, fat and lard). In order to produce an effluent suitable for stream discharge, chemical coagulation and electrocoagulation techniques have been particularly explored at the laboratory pilot scale for organic compounds removal from slaughterhouse effluent. The purpose of this work was to investigate the feasibility of treating cattle-slaughterhouse wastewater by combined chemical coagulation and electrocoagulation process to achieve the required standards. The influence of the operating variables such as coagulant dose, electrical potential and reaction time on the removal efficiencies of major pollutants was determined. The rate of removal of pollutants linearly increased with increasing doses of PACl and applied voltage. COD and BOD(5) removal of more than 99% was obtained by adding 100 mg/L PACl and applied voltage 40 V. The experiments demonstrated the effectiveness of chemical and electrochemical techniques for the treatment of slaughterhouse wastewaters. Consequently, combined processes are inferred to be superior to electrocoagulation alone for the removal of both organic and inorganic compounds from cattle-slaughterhouse wastewater.

Slaughterhouse Wastewater Treatment by Combined Chemical Coagulation and Electrocoagulation Process

Science.gov (United States)

Bazrafshan, Edris; Kord Mostafapour, Ferdos; Farzadkia, Mehdi; Ownagh, Kamal Aldin; Mahvi, Amir Hossein

2012-01-01

Slaughterhouse wastewater contains various and high amounts of organic matter (e.g., proteins, blood, fat and lard). In order to produce an effluent suitable for stream discharge, chemical coagulation and electrocoagulation techniques have been particularly explored at the laboratory pilot scale for organic compounds removal from slaughterhouse effluent. The purpose of this work was to investigate the feasibility of treating cattle-slaughterhouse wastewater by combined chemical coagulation and electrocoagulation process to achieve the required standards. The influence of the operating variables such as coagulant dose, electrical potential and reaction time on the removal efficiencies of major pollutants was determined. The rate of removal of pollutants linearly increased with increasing doses of PACl and applied voltage. COD and BOD5 removal of more than 99% was obtained by adding 100 mg/L PACl and applied voltage 40 V. The experiments demonstrated the effectiveness of chemical and electrochemical techniques for the treatment of slaughterhouse wastewaters. Consequently, combined processes are inferred to be superior to electrocoagulation alone for the removal of both organic and inorganic compounds from cattle-slaughterhouse wastewater. PMID:22768233

Fungal chitosan production from potato processing wastewater and its characterization

International Nuclear Information System (INIS)

Khalaf, S.A.; Khalaf, M.A.

2005-01-01

Potato processing wastewater (PPW) was collected and analyzed for biological oxygen demand BOD, chemical oxygen demand (COD), total suspended solids (TSS), total nitrogen and starch content. A fungal strain of Aspergillus niger treated with ultraviolet (UV) radiation was evaluated for its ability to produce chitosan from PPW. Active UV-irradiated isolate, coded A. niger UV-2, was able to reduce COD by about 86.15% with over productivity of chitosan of 1630 mgl -1 after 5 days of its cultivation in PPW. Extractable chitosan from this isolate had a degree of deacetylation of 88.4% and a molecular weight l.lxlo 5 Da. Also, the extractable chitosan at concentration 600 mgl -1 exhibited the maximum antibacterial activity compared with crab shell chitosan

Physicochemical Characteristics of River Water Downstream of a Large Tropical Hydroelectric Dam

Directory of Open Access Journals (Sweden)

Teck-Yee Ling

2016-01-01

Full Text Available Water quality in the downstream river of a hydroelectric dam may be affected by the structural design and operation. To date, little is known about the water quality downstream of the largest dam in Malaysia, the Bakun hydroelectric dam. Therefore, the objective of the study was to determine the water quality downstream of the dam when the spillway was closed and when it was opened. Results of the study indicate that the dam plays a significant role in regulating the water quality downstream of it. When the spillway was closed, pH and oxygen were lower in the river where DO was below 5 mg/L. When the spillway was opened, the water quality improved in terms of oxygen content (>8.0 mg/L, total sulphide (TS, and chemical oxygen demand (COD but deteriorated in terms of five-day biochemical oxygen demand (BOD5, total ammonia nitrogen (TAN, and total phosphorus (TP. Additionally, the intensity of the impacts, particularly BOD5, COD, and TAN, shows a declining trend as distance from the dam increases. This study shows that impacts on the water quality extend to a distance of 32 km from the dam particularly turbidity and DO and opening the spillway changes the water quality significantly.

Sulfamethoxazole abatement by photo-Fenton

International Nuclear Information System (INIS)

Gonzalez, Oscar; Sans, Carme; Esplugas, Santiago

2007-01-01

The objective of this work was to study the abatement of 200 mg L -1 sulfamethoxazole (SMX) solution by means of photo-Fenton process. Biodegradability of the treated solutions was followed by the ratio biochemical oxygen demand at five days/chemical oxygen demand (BOD 5 /COD) and toxicity by Microtox[reg] and inhibition tests. Experiments with different initial concentration of H 2 O 2 were carried out. The initial amount of Fe 2+ and pH of the solution were set at 10 mg L -1 and 2.8 respectively. The temperature of the reactor was kept constant in all the experiments (25 ± 0.8 deg. C). Photo-Fenton process is thought to be a successful treatment step to improve the biodegradability of wastewater containing SMX. The complete antibiotic removal was achieved for a H 2 O 2 dose over 300 mg L -1 . Biodegradability (BOD 5 /COD) rose from zero (SMX solution) to values higher than 0.3 (treated solutions). Toxicity and inhibition tests pointed out in the same direction: oxidized intermediates for initial H 2 O 2 dose over 300 mg L -1 showed no toxicity effects on pure bacteria and no inhibition on activated sludge activity

Spatial-temporal variation of surface water quality in the downstream region of the Jakara River, north-western Nigeria: A statistical approach.

Science.gov (United States)

Mustapha, Adamu; Aris, Ahmad Zaharin; Ramli, Mohammad Firuz; Juahir, Hafizan

2012-01-01

The pollution status of the downstream section of the Jakara River was investigated. Dissolved oxygen (DO), 5-day biochemical oxygen demand (BOD(5)), chemical oxygen demand (COD), suspended solids (SS), pH, conductivity, salinity, temperature, nitrogen in the form of ammonia (NH(3)), turbidity, dissolved solids (DS), total solids (TS), nitrates (NO(3)), chloride (Cl) and phosphates (PO(3-)(4)) were evaluated, using both dry and wet season samples, as a measure of variation in surface water quality in the area. The results obtained from the analyses were correlated using Pearson's correlation matrix, principal component analysis (PCA) and paired sample t-tests. Positive correlations were observed for BOD(5), NH(3), COD, and SS, turbidity, conductivity, salinity, DS, TS for dry and wet seasons, respectively. PCA was used to investigate the origin of each water quality parameter, and yielded 5 varimax factors for each of dry and wet seasons, with 70.7 % and 83.1 % total variance, respectively. A paired sample t-test confirmed that the surface water quality varies significantly between dry and wet season samples (P < 0.01). The source of pollution in the area was concluded to be of anthropogenic origin in the dry season and natural origins in the wet season.

Electron beam treatment of wastewater

International Nuclear Information System (INIS)

Arai, H.; Hosono, M.; Shimizu, K.; Sugiyama, M.

1991-01-01

Supernatant comes from dewaterization of sewage sludge, and contains biologically nondegradable organics so that it is hard to be treated by conventional activated sludge. By electron beam (EB) irradiation, any kinds of organics in water can be oxidized to biodegradable organic acids. We studied the treatment of supernatant by application of this effect. The direct irradiation of the original supernatant was found not to be so effective to decrease COD. In order to increase the irradiation effect, supernatant was pretreated biologically to decrease the biodegradable organics in it. The chemical oxygen demand (COD) and biochemical oxygen demand (BOD) were decreased from 800 and 910 mg/L to 78 and 5 mg/L by this pretreatment, respectively. This pretreated supernatant was irradiated by EB of 2 MeV using a batch type reactor. The COD was gradually decreased with dose. In contrast, BOD was increased markedly, indicating increase in biodegradability. The irradiated sample water was treated biologically again. After the final biological treatment, COD was decreased below 30 mg/L in the case of 10 - 12 kGy irradiation. Finally, the initial COD of 800 mg/L was decreased below 30 mg/L by the combination of EB irradiation and biological treatment. The cost of irradiation for this process was evaluated preliminarily. (author)

ABILITY OF BACTERIAL CONSORTIUM: Bacillus coagulans, Bacilus licheniformis, Bacillus pumilus, Bacillus subtilis, Nitrosomonas sp. and Pseudomonas putida IN BIOREMEDIATION OF WASTE WATER IN CISIRUNG WASTE WATER TREATMENT PLANT

Directory of Open Access Journals (Sweden)

Ratu SAFITRI

2015-10-01

Full Text Available This study was conducted in order to determine the ability of bacterial consortium: Bacillus coagulans, Bacilus licheniformis, Bacillus pumilus, Bacillus subtilis, Nitrosomonas sp., and Pseudomonas putida in bioremediation of wastewater origin Cisirung WWTP. This study uses an experimental method completely randomized design (CRD, which consists of two treatment factors (8x8 factorial design. The first factor is a consortium of bacteria (K, consisting of 8 level factors (k1, k2, k3, k4, k5, k6, k7, and k8. The second factor is the time (T, consisting of a 7 level factors (t0, t1, t2, t3, t4, t5, t6, and t7. Test parameters consist of BOD (Biochemical Oxygen Demand, COD (Chemical Oxygen Demand, TSS (Total Suspended Solid, Ammonia and Population of Microbes during bioremediation. Data were analyzed by ANOVA, followed by Duncan test. The results of this study showed that the consortium of Bacillus pumilus, Bacillus subtilis, Bacillus coagulans, Nitrosomonas sp., and Pseudomonas putida with inoculum concentration of 5% (k6 is a consortium of the most effective in reducing BOD 71.93%, 64.30% COD, TSS 94.85%, and 88.58% of ammonia.

Dye Removal From Textile Waste Water Through The Adsorption By Pumice Used In Stone Washing

Directory of Open Access Journals (Sweden)

Körlü Aysegül Ekmekçi

2015-09-01

Full Text Available Because the waste production is inevitable in almost all industries, the elimination of these wastes is a requirement in terms of environmental regulations and welfare of all the creatures in the future. In this study, the use of the waste pumice stones of a denim washing mill is intended to eliminate the pollutant by a waste material and obtain economic benefits by converting it to the adsorbent. The pollutants in the effluents obtained from three different localisations of waste water treatment system of the same factory were removed through the adsorption. The experimental studies were carried out in three different steps; characterisation of adsorbent before and after adsorption; adsorption isotherm studies and biological oxygen demand (BOD, chemical oxygen demand (COD measurements. Characterisation studies showed that the waste pumice has almost the same structural properties with unused one except the existence of some organic residues coming from washing process. The results of adsorption studies conducted at the adsorbent concentrations changing from 5 to 35 g/l revealed that the decolourisation was initial dye-concentration dependent. According to the BOD and COD measurements, the supernatants obtained at the end of adsorption could be assumed as somewhat polluted and this result indicates that the organic impurities other than indigo were also removed through the adsorption.

A Preliminary Study of Water Quality Index in Terengganu River Basin, Malaysia

International Nuclear Information System (INIS)

Suratman, S.; Mohd, S.M.I.; Hee, Y.Y.; Bedurus, E.A.; Latif, M.T.

2015-01-01

The Malaysian Department of Environment-Water Quality Index (DOE-WQI) was determined for the Terengganu River basin which is located at the coastal water of the southern South China Sea between July and October 2008. Monthly samplings were carried out at ten sampling stations within the basin. Six parameters listed in DOE-WQI were measured based on standard methods: pH, dissolved oxygen (DO), biochemical oxygen demand (BOD), chemical oxygen demand (COD), total suspended solids (TSS) and ammonical nitrogen (AN). The results indicated the impact of various anthropogenic activities which contribute to high values of BOD, COD, TSS and AN at middle and downstream stations, as compared with the upstream of the basin. The reverses were true for the pH and DO values. The DOE-WQI ranged from 71.5-94.6 % (mean 86.9 %), which corresponded to a classification status range from slightly polluted to clean. With respect to the Malaysia National Water Quality Standards (NWQS), the level of most of the parameters measured remained at Class I which is suitable for the sustainable conservation of the natural environment, for water supply without treatment and as well as for very sensitive aquatic species. It is suggested that monitoring should be carried out continuously for proper management of this river basin. (author)

Characteristics of Leachate and Their Effect on Shallow Groundwater Quality (Case Study : TPA Cipayung, Depok)

Science.gov (United States)

Widiastuti, Atika; Hartono, Djoko M.; Moersidik, Setyo S.; Gusniani, Irma

2018-03-01

The problems arising from landfill activity is leaked leachate that is not absorbed well into leachate stabilization pond which furthermore contaminates shallow groundwater around landfill, include Cipayung landfill. The aims of this study is to determine the characteristics of leachate and their effect on shallow groundwater quality around landfill based on temperature, pH, Total Suspended Solids (TSS), Biological Oxygen Demand (BOD), Chemical Oxygen Demand (COD), Total Nitrogen (TN), Mercury (Hg), and fecal coliform. Data were analyzed based on leachate samples at influent point, effluent point, and 7 sampling points of residents’s well with distance variation every 100 meters within 300 meters radius having leachate stabilization pond as benchmark. According to the standard of Indonesia’s Ministry of Environment and Forestry law No. 59 of 2016, the results showed that leachate quality was still above the standard of BOD, COD, and Total Nitrogen parameters; 4178.0 mg/L, 70556.0 mg/L and 373.3 mg/L for influent point, and 3142.0 mg/L, 9055.2 mg/L, and 350 mg/L for the effluent point. Pollution Index of shallow groundwater is between lightly and moderately contaminated. This study showed that the further the distance between sampling point and leachate stabilization pond is, the lower the Polution Index is.

U.S. natural gas liquids supply and demand

International Nuclear Information System (INIS)

Urquhart, W.L.

1996-01-01

United States supply and demand situation for natural gas liquids (NGL) was reviewed. The presentation was in four parts: (1) key assumptions for U.S. NGL supply and demand, (2) specific balances for ethane, propane, and butane, (3) some of the key changes now occurring at the customer level, and how these might affect NGLs, and (4) a suggestion of where the future might deviate from projections so severely that projections could be fundamentally wrong. Despite such 'exogenous variables' higher demand projections downstream in the chemical industry were said to be appearing, albeit in scattered fashion. It was estimated that even fractionally higher economic growth could add 3.5 billion pounds to ethylene demand in the USA in the year 2005. 15 figs

Characterization and treatment of Denizli landfill leachate using anaerobic hybrid/aerobic CSTR systems.

Science.gov (United States)

Ağdağ, Osman Nuri

2011-01-01

Leachate generated in municipal solid waste landfill contains large amounts of organic and inorganic contaminants. In the scope of the study, characterization and anaerobic/aerobic treatability of leachate from Denizli (Turkey) Sanitary Landfill were investigated. Time-based fluctuations in characteristics of leachate were monitored during a one-year period. In characterization study; chemical oxygen demand (COD), biochemical oxygen demand (BOD) dissolved oxygen, temperature, pH, alkalinity, volatile fatty acids, total nitrogen, NH4-N, BOD5/COD ratio, suspended solid, inert COD, anaerobic toxicity assay and heavy metals concentrations in leachate were monitored. Average COD, BOD and NH4-N concentration in leachate were measured as 18034 mg/l, 11504 mg/l and 454 mg/l, respectively. Generally, pollution parameters in leachate were higher in summer and relatively lower in winter due to dilution by precipitation. For treatment of leachate, two different reactors, namely anaerobic hybrid and aerobic completely stirred tank reactor (CSTR) having effective volumes of 17.7 and 10.5 litres, respectively, were used. After 41 days of start-up period, leachate was loaded to hybrid reactor at 10 different organic loading rates (OLRs). OLR was increased by increasing COD concentrations. COD removal efficiency of hybrid reactor was carried out at a maximum of 91%. A percentage of 96% of residual COD was removed in the aerobic reactor. NH4-N removal rate in CSTR was quite high. In addition, high methane content was obtained as 64% in the hybrid reactor. At the end of the study, after 170 operation days, it can be said that the hybrid reactor and CSTR were very effective for leachate treatment.

Treatment and decolorization of biologically treated Palm Oil Mill Effluent (POME) using banana peel as novel biosorbent.

Science.gov (United States)

Mohammed, Rafie Rushdy; Chong, Mei Fong

2014-01-01

Palm Oil Mill Effluent (POME) treatment has always been a topic of research in Malaysia. This effluent that is extremely rich in organic content needs to be properly treated to minimize environmental hazards before it is released into watercourses. The main aim of this work is to evaluate the potential of applying natural, chemically and thermally modified banana peel as sorbent for the treatment of biologically treated POME. Characteristics of these sorbents were analyzed with BET surface area and SEM. Batch adsorption studies were carried out to remove color, total suspended solids (TSS), chemical oxygen demand (COD), tannin and lignin, and biological oxygen demand (BOD) onto natural banana peel (NBP), methylated banana peel (MBP), and banana peel activated carbon (BPAC) respectively. The variables of pH, adsorbent dosage, and contact time were investigated in this study. Maximum percentage removal of color, TSS, COD, BOD, and tannin and lignin (95.96%, 100%, 100%, 97.41%, and 76.74% respectively) on BPAC were obtained at optimized pH of 2, contact time of 30 h and adsorbent dosage of 30 g/100 ml. The isotherm data were well described by the Redlich-Peterson isotherm model with correlation coefficient of more than 0.99. Kinetic of adsorption was examined by Langergren pseudo first order, pseudo second order, and second order. The pseudo second order was identified to be the governing mechanism with high correlation coefficient of more than 0.99. Copyright © 2013 Elsevier Ltd. All rights reserved.

Overview of the state of the art of constructed wetlands for decentralized wastewater management in Brazil.

Science.gov (United States)

Machado, A I; Beretta, M; Fragoso, R; Duarte, E

2017-02-01

Conventional wastewater treatment plants (WWTPs) commonly require large capital investments as well as operation and maintenance costs. Constructed wetlands (CWs) appear as a cost-effective treatment, since they can remove a broad range of contaminants by a combination of physical, chemical and biological processes with a low cost. Therefore, CWs can be successfully applied for decentralized wastewater treatment in regions with low population density and/or with large land availability as Brazil. The present work provides a review of thirty nine studies developed on CWs implemented in Brazil to remove wastewater contaminants. Brazil current sanitation data is also considered to evaluate the potential role of CWs as decentralized wastewater treatment. Performance of CWs was evaluated according to (i) type of wetland system, (ii) different support matrix (iii) vegetation species and (iv) removal efficiency of chemical oxygen demand (COD), biological oxygen demand (BOD 5 ), nitrogen (N), and phosphorus (P). The reviewed CWs in overall presented good efficiencies, whereas H-CWs achieved the highest removals for P, while the higher results for N were attained on VF-CW and for COD and BOD 5 on HF-CW. Therefore, was concluded that CWs are an interesting solution for decentralized wastewater treatment in Brazil since it has warm temperatures, extensive radiation hours and available land. Additionally, the low percentage of population with access to the sewage network in the North and Northeast regions makes these systems especially suitable. Hence, the further implementation of CW is encouraged by the authors in regions with similar characteristics as Brazil. Copyright © 2016 Elsevier Ltd. All rights reserved.

Low cost chemical oxygen demand sensor based on electrodeposited nano-copper film

Directory of Open Access Journals (Sweden)

Hamdy H. Hassan

2018-02-01

Full Text Available A commercially available copper electrical cable and pure Cu disk were used as substrates for the electrodeposition of copper nanoparticles (nano-Cu. The surface morphology of the prepared nano-Cu/Cu electrodes was investigated by scanning electron microscope (SEM and energy dispersive X-ray spectrometer (EDX. The bare copper substrates and the nano-copper modified electrodes were utilized and optimized for electrochemical assay of chemical oxygen demand (COD using glycine as a standard. A comparison was made among the four electrodes (i.e., bare and nano-Cu coated copper cable and pure copper disk as potential COD sensors. The oxidation behavior of glycine was investigated on the surface of the prepared sensors using linear sweep voltammetry (LSV. The results indicate significant enhancement of the electrochemical oxidation of glycine by the deposited nano-Cu. The effects of different deposition parameters, such as Cu2+ concentration, deposition potential, deposition time, pH, and scan rate on the response of the prepared sensors were investigated. Under optimized conditions, the optimal nano-Cu based COD sensor exhibited a linear range of 2–595 mg/L, lower limit of detection (LOD as low as 1.07 mg/L (S/N = 3. The developed method exhibited high tolerance level to Cl− ion where 1.0 M Cl− exhibited minimal influence. The sensor was utilized for the detection of COD in different real water samples. The results obtained were validated using the standard dichromate method.

Complete physico-chemical treatment for coke plant effluents.

Science.gov (United States)

Ghose, M K

2002-03-01

Naturally found coal is converted to coke which is suitable for metallurgical industries. Large quantities of liquid effluents produced contain a large amount of suspended solids, high COD, BOD, phenols, ammonia and other toxic substances which are causing serious pollution problem in the receiving water to which they are discharged. There are a large number of coke plants in the vicinity of Jharia Coal Field (JCF). Characteristics of the effluents have been evaluated. The present effluent treatment systems were found to be inadequate. Physico-chemical treatment has been considered as a suitable option for the treatment of coke plant effluents. Ammonia removal by synthetic zeolite, activated carbon for the removal of bacteria, viruses, refractory organics, etc. were utilized and the results are discussed. A scheme has been proposed for the complete physico-chemical treatment, which can be suitably adopted for the recycling, reuse and safe disposal of the treated effluent. Various unit process and unit operations involved in the treatment system have been discussed. The process may be useful on industrial scale at various sites.

Pecan shell-based granular activated carbon for treatment of chemical oxygen demand (COD) in municipal wastewater.

Science.gov (United States)

Bansode, R R; Losso, J N; Marshall, W E; Rao, R M; Portier, R J

2004-09-01

The present investigation was undertaken to compare the adsorption efficiency of pecan shell-based granular activated carbon with the adsorption efficiency of the commercial carbon Filtrasorb 200 with respect to uptake of the organic components responsible for the chemical oxygen demand (COD) of municipal wastewater. Adsorption efficiencies for these two sets of carbons (experimental and commercial) were analyzed by the Freundlich adsorption model. The results indicate that steam-activated and acid-activated pecan shell-based carbons had higher adsorption for organic matter measured as COD, than carbon dioxide-activated pecan shell-based carbon or Filtrasorb 200 at all the carbon dosages used during the experiment. The higher adsorption may be related to surface area as the two carbons with the highest surface area also had the highest organic matter adsorption. These results show that granular activated carbons made from agricultural waste (pecan shells) can be used with greater effectiveness for organic matter removal from municipal wastewater than a coal-based commercial carbon. Copyright 2004 Elsevier Ltd.

Detoxifying of high strength textile effluent through chemical and bio-oxidation processes.

Science.gov (United States)

Manekar, Pravin; Patkar, Guarav; Aswale, Pawan; Mahure, Manisha; Nandy, Tapas

2014-04-01

Small-scale textile industries (SSTIs) in India struggled for the economic and environmental race. A full-scale common treatment plant (CETP) working on the principle of destabilising negative charge colloidal particles and bio-oxidation of dissolved organic failed to comply with Inland Surface Waters (ISW) standards. Thus, presence of intense colour and organics with elevated temperature inhibited the process stability. Bench scale treatability studies were conducted on chemical and biological processes for its full-scale apps to detoxify a high strength textile process effluent. Colour, SS and COD removals from the optimised chemical process were 88%, 70% and 40%, respectively. Heterotrophic bacteria oxidised COD and BOD more than 84% and 90% at a loading rate 0.0108kgm(-3)d(-1) at 3h HRT. The combined chemical and bio-oxidation processes showed a great promise for detoxifying the toxic process effluent, and implemented in full-scale CETP. The post-assessment of the CETP resulted in detoxify the toxic effluent. Copyright © 2014 Elsevier Ltd. All rights reserved.

Peroxone mineralization of chemical oxygen demand for direct potable water reuse: Kinetics and process control.

Science.gov (United States)

Wu, Tingting; Englehardt, James D

2015-04-15

Mineralization of organics in secondary effluent by the peroxone process was studied at a direct potable water reuse research treatment system serving an occupied four-bedroom, four bath university residence hall apartment. Organic concentrations were measured as chemical oxygen demand (COD) and kinetic runs were monitored at varying O3/H2O2 dosages and ratios. COD degradation could be accurately described as the parallel pseudo-1st order decay of rapidly and slowly-oxidizable fractions, and effluent COD was reduced to below the detection limit (<0.7 mg/L). At dosages ≥4.6 mg L(-1) h(-1), an O3/H2O2 mass ratio of 3.4-3.8, and initial COD <20 mg/L, a simple first order decay was indicated for both single-passed treated wastewater and recycled mineral water, and a relationship is proposed and demonstrated to estimate the pseudo-first order rate constant for design purposes. At this O3/H2O2 mass ratio, ORP and dissolved ozone were found to be useful process control indicators for monitoring COD mineralization in secondary effluent. Moreover, an average second order rate constant for OH oxidation of secondary effluent organics (measured as MCOD) was found to be 1.24 × 10(7) ± 0.64 × 10(7) M(-1) S(-1). The electric energy demand of the peroxone process is estimated at 1.73-2.49 kW h electric energy for removal of one log COD in 1 m(3) secondary effluent, comparable to the energy required for desalination of medium strength seawater. Advantages/disadvantages of the two processes for municipal wastewater reuse are discussed. Copyright © 2015 Elsevier Ltd. All rights reserved.

BIODEGRADATION OF SUGARCANE VINASSES BY THE WHITE-ROT FUNGI Pleurotus ostreatus IN A PACKED BED REACTOR

Directory of Open Access Journals (Sweden)

W.A. Tapie

2016-08-01

Full Text Available Sugarcane vinasses are considered a complex effluent because of its organic load, low pH, high temperature, and by the presence of recalcitrant substances such as melanoidins and phenolic compounds. The aim of this work was to evaluate the potential of the fungus Pleurotus ostreatus to carry out the biodegradation of sugarcane vinasses in a fixed-bed bioreactor. The experiments evidence the potential of the fungus Pleurotus ostreatus to carry out the decolorization (83%, the removal of the Chemical Oxygen Demand (COD=87% and the Biochemical Oxygen Demand (BOD5=92%, the reduction of total suspended solids (83% and volatile suspended solids (72% of vinasses. The technical simplicity of the proposed alternative as well as process performance reveals the potential of the fungus Pleurotus ostreatus for the treatment of sugarcane mill effluents.

Influence of vegetation and gravel mesh on the tertiary treatment of wastewater from a cosmetics industry.

Science.gov (United States)

Vlyssides, Apostolos G; Mai, Sofia T H; Barampouti, Elli Maria P; Loukakis, Haralampos N

2009-07-01

To estimate the influence of gravel mesh (fine and coarse) and vegetation (Phragmites and Arundo) on the efficiency of a reed bed, a pilot plant was included after the wastewater treatment plant of a cosmetic industry treatment system according to a 22 factorial experimental design. The maximum biochemical oxygen demand (BOD5), chemical oxygen demand (COD) and total phosphorous (TP) reduction was observed in the reactor, where Phragmites and fine gravel were used. In the reactor with Phragmites and coarse gravel, the maximum total Kjeldahl nitrogen (TKN) and total suspended solids (TSS) reduction was observed. The maximum total solids reduction was measured in the reed bed, which was filled with Arundo and coarse gravel. Conclusively, the treatment of a cosmetic industry's wastewater by reed beds as a tertiary treatment method is quite effective.

Community structure, phytoplankton density and physical-chemical factor of batang palangki waters of sijunjung regency, west sumatera

Science.gov (United States)

Gusmaweti; Deswati, L.

2018-03-01

The long-term goal of this study is to provide an overview of the presence of phytoplankton in support of its functions in the waters of Batang Palangki as a conservation area of information on river water management, especially for Batang Palangki stakeholders. Specific targets to be achieved in achieving these objectives are (1) to know the density of phytoplankton, index of diversity of species, equitabilty index, domination index, and in Batang Palangki waters, and (2) to analyze the chemical and physical factors of the waters. The sampling method of phytoplankton is purposive sampling. The phytoplankton sampling is done By filtering 100 liters of water into the net plankton no 25 and filtered into the 25 cc, and then identified. The determination of water quality such as water temperature, water pH and watercolour. dissolved oxygen (DO) and BOD, and Hg content (mercury). The results showed that phytoplankton found from each of station was 370 individualis per liter with the highest density found in the station I of 155. The number of genus was 7, namely Neidium, Gyrogsima, Synedra, Frustulia, Fragillaria, Nitzschia and Peridinium. The diversity index averaged at 0.45, equabilty index averaged at 0.54, while the dominance index averaged at 0.28. Physical and chemical factor measurement results found that water temperature averaged at 26 °C, transparency ranged from 12 - 30 cm, velocity speed ranged from 8 - 15 m/s, while chemical factors such as DO, BOD, and COD ranged from 5.25 to 5.96 mg/L, 3.28 - 3.49 mg/L, and 47.05 - 76.25 mg/L respectively. Likewise, TOM measured in this research was 9.61 - 2.10 mg/L while Hg content ranged from 0.098 - 0.208 mg/L.

Prolonged aerobic degradation of shredded and pre-composted municipal solid waste: report from a 21-year study of leachate quality characteristics.

Science.gov (United States)

Grisey, Elise; Aleya, Lotfi

2016-01-01

The objective of this study was to assess the degree of long-term waste maturation at a closed landfill (Etueffont, France) over a period of 21 years (1989-2010) through analysis of the physicochemical characteristics of leachates as well as biochemical oxygen demand (BOD), chemical oxygen demand (COD), and metal content in waste. The results show that the leachates, generated in two different sections (older and newer) of the landfill, have low organic, mineral, and metallic loads, as the wastes were mainly of household origin from a rural area where sorting and composting were required. Based on pH and BOD/COD assessments, leachate monitoring in the landfill's newer section showed a rapid decrease in the pollution load over time and an early onset of methanogenic conditions. The closing of the older of the two sections contributed to a significant decline for the majority of parameters, attributable to degradation and leaching. A gradual decreasing trend was observed after waste placement had ceased in the older section, indicating that degradation continued and the waste mass had not yet fully stabilized. At the end of monitoring, leachates from the two landfill linings contained typical old leachates in the maturation period, with a pH ≥ 7 and a low BOD/COD ratio indicating a low level of waste biodegradability. Age actually contributes to a gradual removal of organic, inorganic, and metallic wastes, but it is not the only driving factor behind advanced degradation. The lack of compaction and cover immediately after deposit extended the aerobic degradation phase, significantly reducing the amount of organic matter. In addition, waste shredding improved water infiltration into the waste mass, hastening removal of polluting components through percolation.

Preliminary Study of Greywater Treatment through Rotating Biological Contactor

Directory of Open Access Journals (Sweden)

Ashfaq Ahmed Pathan

2011-07-01

Full Text Available The characteristics of the greywater vary from country to country and it depends upon the cultural and social behavior of the respective country. There was a considerable need to characterize and recycle the greywater. In this regard greywater was separated from the black water and analyzed for various physiochemical parameters. Among various greywater recycling treatment technologies, RBC (Rotating Biological Contactor is more effective treatment technique in reducing COD (Chemical Oxygen Demand and organic matters from the greywater. But this technology was not applied and tested in Pakistan. There was extensive need to investigate the RBC technology for greywater recycling at small scale before applying at mass scale. To treat the greywater, a single-stage RBC simulator was designed and developed at laboratory scale. An electric motor equipped with gear box to control the rotations of the disks was mounted on the tank. The simulator was run at the rate of 1.7 rpm. The disc area of the RBC was immersed about 40% in the greywater. Water samples were collected at each HRT (Hydraulic Retention Time and analyzed for the parameters such as pH, conductivity, TDS (Total Dissolved Solids, salinity, BOD5 (Biochemical Oxygen Demand, COD and suspended solids by using standard methods. The results are encouraging with percentage removal of BOD5 and COD being 53 and 60% respectively.

Combination of ozonation, activated carbon, and biological aerated filter for advanced treatment of dyeing wastewater for reuse.

Science.gov (United States)

Zou, Xiao-Ling

2015-06-01

Laboratorial scale experiments were performed to investigate and evaluate the performance and removal characteristics of organics, color, and genotoxicity by an integrated process including ozonation, activated carbon (AC), and biological aerated filter (BAF) for recycling biotreated dyeing wastewater (BTDW) collected from a cotton textile factory. Influent chemical oxygen demand (COD) in the range of 156 - 252 mg/L, 5-day biochemical oxygen demand (BOD5) of 13.5 - 21.7 mg/L, and color of 58 - 76° were observed during the 20-day continuous operation. Outflows with average COD of 43 mg/L, BOD5 of 6.6 mg/L, and color of 5.6° were obtained after being decontaminated by the hybrid system with ozone dosage of 0.25 mg O3applied/mg COD0, 40 min ozonation contact time, 30 min hydraulic retention time (HRT) for AC treatment, and 2.5 h HRT for BAF treatment. More than 82 % of the genotoxicity of BTDW was eliminated in the ozonation unit. The genotoxicity of the BAF effluent was less than 1.33 μg 4-nitroquinoline-N-oxide/L. Ozonation could change the organics molecular structures, destroy chromophores, increase the biodegradability, and obviously reduce the genotoxicity of BTDW. Results showed that the combined process could guarantee water reuse with high quality.

Using full-scale duckweed ponds as the finish stage for swine waste treatment with a focus on organic matter degradation.

Science.gov (United States)

Mohedano, R A; Costa, R H R; Hofmann, S M; Belli Filho, P

2014-01-01

The rapid increase in the number of swine has caused pronounced environmental impacts worldwide, especially on water resources. As an aggregate, smallholdings have an important role in South American pork production, contributing to the net diffusion of pollution. Thus, duckweed ponds have been successfully used for swine waste polishing, mainly for nutrient removal. Few studies have been carried out to assess organic matter degradation in duckweed ponds. Hence, the present study evaluated the efficiency of two full-scale duckweed ponds for organic matter reduction of swine waste on small pig farms. Duckweed ponds, in series, received the effluent after an anaerobic biodigester and storage pond, with a flow rate of 1 m(3) day(-1). After 1 year of monitoring, an improvement in effluent quality was observed, with a reduction in biochemical oxygen demand (BOD) and total chemical oxygen demand (tCOD), respectively, of 94.8 and 96.7%, operating at a loading rate of approximately 27 kgBOD ha(-1) day(-1) and 131 kgCOD ha(-1) day(-1). Algae inhibition due to duckweed coverage was strongly observed in the pond effluent, where chlorophyll a and turbidity remained below 25 μg L(-1) and 10 NTU. Using the study conditions described herein, duckweed ponds were shown to be a suitable technology for swine waste treatment, contributing to the environmental sustainability of rural areas.

Batch leachate treatment using stirred electrocoagulation reactor with variation of residence time and stirring rate

Science.gov (United States)

Sitorus, I. S.; Astono, W.; Iswanto, B.

2018-01-01

This study aims to reduce pollutant levels of the leachate by electrocoagulation method using a stirred electrocoagulation reactor as the electrochemical water treatment. The release of active coagulants as metallic ions took place in the anode, while in the cathode, the electrolysis reaction in the form of hydrogen gas dischargeoccurred. The source of wastewater is Waste Water Treatment Plant inlet III of Bantar Gebang, Bekasi. Some parameters were analyzed in this research, i.e., Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), NH3, NO3 -, NO2 -, N-total, and organic substances as well as the microorganism growth before and after electrocoagulation, with variations of detention time (seconds) of 10, 20, 120, 600 and rapid mixing conditions (rpm) of 60, 100 and 200. The results show that the greater the rapid mixing speed and the detention time of electrolysis, the higher the removal of contaminants in liquid waste. The optimum condition of electrocoagulation was encountered at 200 rpm rapid mixing with 600 seconds of processing time. The removal efficiencies of electrocoagulation method for each parameter are TSS of 46.80%, BOD5 of 71.33%, COD of 73.77%, Pb of 62.5%,and NH3-N of 57.92%,whereas the pH value has been increased from 8.03 to 8.95. The electrocoagulation method can reduce levels of pollutants, complying with the environmental standards.

Biodegradation and kinetics of organic compounds and heavy metals in an artificial wetland system (AWS) by using water hyacinths as a biological filter.

Science.gov (United States)

Rodríguez-Espinosa, P F; Mendoza-Pérez, J A; Tabla-Hernandez, J; Martínez-Tavera, E; Monroy-Mendieta, M M

2018-01-02

The objective of the present study was to investigate the ability of water hyacinth (Eichhornia crassipes) to absorb organic compounds (potassium hydrogen phthalate, sodium tartrate, malathion, 2,4-dichlorophenoxy acetic acid (2,4-D), and piroxicam). For the aforementioned purpose, an artificial wetland system (AWS) was constructed and filled with water hyacinth collected from the Valsequillo Reservoir, Puebla, Mexico. Potassium hydrogen phthalate and sodium tartrate were measured in terms of chemical oxygen demand (COD) and biological oxygen demand (BOD). The present study indicated that the water hyacinths absorbed nearly 1.8-16.6 g of COD kg -1 dm (dry mass of water hyacinth), while the absorbance efficiency of BOD was observed to be 45.8%. The results also indicated that the maximum absorbance efficiency of malathion, 2,4-D, and piroxicam was observed to be 67.6%, 58.3%, and 99.1%, respectively. The kinetics of organic compounds fitted different orders as malathion followed a zeroth-order reaction, while 2,4-D and piroxicam followed the first-order reactions. Preliminary assessment of absorption of heavy metals by the water hyacinth in the AWS was observed to be (all values in mg g -1 ) 7 (Ni), 13.4 (Cd), 16.3 (Pb), and 17.5 (Zn) of dry biomass, thus proving its feasibility to depurate wastewater.

Application of regression model on stream water quality parameters

International Nuclear Information System (INIS)

Suleman, M.; Maqbool, F.; Malik, A.H.; Bhatti, Z.A.

2012-01-01

Statistical analysis was conducted to evaluate the effect of solid waste leachate from the open solid waste dumping site of Salhad on the stream water quality. Five sites were selected along the stream. Two sites were selected prior to mixing of leachate with the surface water. One was of leachate and other two sites were affected with leachate. Samples were analyzed for pH, water temperature, electrical conductivity (EC), total dissolved solids (TDS), Biological oxygen demand (BOD), chemical oxygen demand (COD), dissolved oxygen (DO) and total bacterial load (TBL). In this study correlation coefficient r among different water quality parameters of various sites were calculated by using Pearson model and then average of each correlation between two parameters were also calculated, which shows TDS and EC and pH and BOD have significantly increasing r value, while temperature and TDS, temp and EC, DO and BL, DO and COD have decreasing r value. Single factor ANOVA at 5% level of significance was used which shows EC, TDS, TCL and COD were significantly differ among various sites. By the application of these two statistical approaches TDS and EC shows strongly positive correlation because the ions from the dissolved solids in water influence the ability of that water to conduct an electrical current. These two parameters significantly vary among 5 sites which are further confirmed by using linear regression. (author)

Evaluation of effluents from bench-scale treatment combinations for landfill leachate in Ibadan, Nigeria.

Science.gov (United States)

Aluko, Olufemi Oludare; Sridhar, Mkc

2014-01-01

The removal of pollutants in landfill leachate was investigated using constructed wetlands, a trickling filter, alum flocculation and coagulation, and a sequencing batch reactor in various combinations. Thirteen combined operations were investigated involving three out of the four unit treatment methods in series. The study was conducted because unit operations, though achieved reductions in pollutants concentrations had effluent values above the national regulatory guideline values. The suspended solids of effluents were permissible in most treatment processes, while reductions in 5-day biochemical oxygen demand (BOD5), chemical oxygen demand (COD) and ammonia (NH3) of leachates ranged from 80% to 97%; 86% to 97% and 92% to 98% respectively. However, there were significant increases in nitrate (85%) and dissolved oxygen of treatment (218%). In addition, the characteristics of the recommended treatment sequence, involving constructed wetlands, alum and trickling filter produced effluents with reductions in colour (97%), alkalinity (97%), BOD (97%), COD (97%) and NH3 (98%), and in metals, except nickel (29% reduction from the influent values). The recommended treatment combination is suitable for effective leachate management at the landfill. The cost of constructing and operating the recommended treatment combination at the facility, for 5 years, would be NGN6,009,750.00 ($38,036.39). The performance should be monitored on site prior to full adoption if effluent characteristics remain consistently low over dry and wet seasons.

Modification of SWAT model for simulation of organic matter in Korean watersheds.

Science.gov (United States)

Jang, Jae-Ho; Jung, Kwang-Wook; Gyeong Yoon, Chun

2012-01-01

The focus of water quality modeling of Korean streams needs to be shifted from dissolved oxygen to algae or organic matter. In particular, the structure of water quality models should be modified to simulate the biochemical oxygen demand (BOD), which is a key factor in calculating total maximum daily loads (TMDLs) in Korea, using 5-day BOD determined in the laboratory (Bottle BOD(5)). Considering the limitations in simulating organic matter under domestic conditions, we attempted to model total organic carbon (TOC) as well as BOD by using a watershed model. For this purpose, the Soil and Water Assessment Tool (SWAT) model was modified and extended to achieve better correspondence between the measured and simulated BOD and TOC concentrations. For simulated BOD in the period 2004-2008, the Nash-Sutcliffe model efficiency coefficient increased from a value of -2.54 to 0.61. Another indicator of organic matter, namely, the simulated TOC concentration showed that the modified SWAT adequately reflected the observed values. The improved model can be used to predict organic matter and hence, may be a potential decision-making tool for TMDLs. However, it needs further testing for longer simulation periods and other catchments.

Chromium (VI) biosorption and removal of chemical oxygen demand by Spirulina platensis from wastewater-supplemented culture medium.

Science.gov (United States)

Magro, Clinei D; Deon, Maitê C; De Rossi, Andreia; Reinehr, Christian O; Hemkemeier, Marcelo; Colla, Luciane M

2012-01-01

The inappropriate discharge of wastewater containing high concentrations of toxic metals is a serious threat to the environment. Given that the microalga Spirulina platensis has demonstrated a capacity for chromium VI (Cr (VI) biosorption, we assessed the ideal concentration of chromium-containing wastewater required for maximum removal of Cr (VI) and chemical oxygen demand (COD) from the environment by using this microalga. The Paracas and Leb-52 strains of S. platensis, with initial wastewater concentrations of 0%, 12.5%, 25%, and 50%, were cultured in Zarrouk medium diluted to 50% under controlled air, temperature, and lighting conditions. The cultures were maintained for 28 days, and pH, biomass growth, COD, and Cr (VI) were assessed. The wastewater concentration influenced microalgal growth, especially at high concentrations. Removal of 82.19% COD and 60.92% Cr (VI) was obtained, but the COD removal was greater than the Cr (VI) removal in both strains of S. platensis.

On-Demand Targeting: Investigating Biology with Proximity-Directed Chemistry.

Science.gov (United States)

Long, Marcus J C; Poganik, Jesse R; Aye, Yimon

2016-03-23

Proximity enhancement is a central chemical tenet underpinning an exciting suite of small-molecule toolsets that have allowed us to unravel many biological complexities. The leitmotif of this opus is "tethering"-a strategy in which a multifunctional small molecule serves as a template to bring proteins/biomolecules together. Scaffolding approaches have been powerfully applied to control diverse biological outcomes such as protein-protein association, protein stability, activity, and improve imaging capabilities. A new twist on this strategy has recently appeared, in which the small-molecule probe is engineered to unleash controlled amounts of reactive chemical signals within the microenvironment of a target protein. Modification of a specific target elicits a precisely timed and spatially controlled gain-of-function (or dominant loss-of-function) signaling response. Presented herein is a unique personal outlook conceptualizing the powerful proximity-enhanced chemical biology toolsets into two paradigms: "multifunctional scaffolding" versus "on-demand targeting". By addressing the latest advances and challenges in the established yet constantly evolving multifunctional scaffolding strategies as well as in the emerging on-demand precision targeting (and related) systems, this Perspective is aimed at choosing when it is best to employ each of the two strategies, with an emphasis toward further promoting novel applications and discoveries stemming from these innovative chemical biology platforms.

The Metropolis-Hastings algorithm, a handy tool for the practice of environmental model estimation : illustration with biochemical oxygen demand data

Directory of Open Access Journals (Sweden)

Franck Torre

2001-02-01

Full Text Available Environmental scientists often face situations where: (i stimulus-response relationships are non-linear; (ii data are rare or imprecise; (iii facts are uncertain and stimulus-responses relationships are questionable. In this paper, we focus on the first two points. A powerful and easy-to-use statistical method, the Metropolis-Hastings algorithm, allows the quantification of the uncertainty attached to any model response. This stochastic simulation technique is able to reproduce the statistical joint distribution of the whole parameter set of any model. The Metropolis-Hastings algorithm is described and illustrated on a typical environmental model: the biochemical oxygen demand (BOD. The aim is to provide a helpful guideline for further, and ultimately more complex, models. As a first illustration, the MH-method is also applied to a simple regression example to demonstrate to the practitioner the ability of the algorithm to produce valid results.

Cleaner processing: a sulphide-free approach for depilation of skins.

Science.gov (United States)

Ranjithkumar, Ammasi; Durga, Jayanthi; Ramesh, Ramakrishnan; Rose, Chellan; Muralidharan, Chellappa

2017-01-01

The conventional unhairing process in leather making utilises large amount of lime and sodium sulphide which is hazardous and poses serious waste disposal concerns. Under acidic conditions, sodium sulphide liberates significant quantities of hydrogen sulphide which causes frequent fatal accidents. Further, the conventional unhairing process involves destruction of the hair leading to increased levels of biological oxygen demand (BOD), chemical oxygen demand (COD), total dissolved solids (TDS) and total suspended solids (TSS) in the effluent. A safe approach is needed to overcome such environmental and health problems through an eco-benign process. The present study deals with a clean technology in which the keratinous body is detached from the dermis using enzymes produced from Bacillus crolab MTCC 5468 by solid state fermentation (SSF) as an alternative to noxious chemicals. Complete unhairing of skin could be achieved with an enzyme concentration of 1.2 % (w/w). The bio-chemical parameters of the spent liquor of the enzymatic process were environmentally favourable when compared with conventional method. The study indicates that the enzymatic unhairing is a safe process which could be used effectively in leather processing to alleviate pollution and health problems.

Impact of urban and industrial effluents on the coastal marine environment in Oran, Algeria.

Science.gov (United States)

Tayeb, A; Chellali, M R; Hamou, A; Debbah, S

2015-09-15

In Algeria most of the urban waste water is dumped without treatment into the Sea. It is tremendously important to assess the consequences of organic matter rich sewage on marine ecosystem. In this study we investigated the effects of industrial and urban sewage on the dissolved oxygen (O2), chemical oxygen demand (COD), biochemical oxygen demands (BOD5), pH, salinity, electrical conductivity (EC), Metal element (Hg, Pb, Cu, Ni, Cr, Cd), petroleum hydrocarbons (HC), oil and grease (OG) in Bay of Oran, Algeria. A ten-year follow-up research showed that the concentrations of oil and grease released into the bionetwork are of higher ecological impact and this needs to be given the desired consideration. Information on bathing water quality revealed that the most beaches in Oran are under the national environmental standard limit. Copyright © 2015 Elsevier Ltd. All rights reserved.

Wastewater Treatment from Batik Industries Using TiO2 Nanoparticles

Science.gov (United States)

Arifan, Fahmi; Nugraheni, FS; Rama Devara, Hafiz; Lianandya, Niken Elsa

2018-02-01

Batik is cultural patterned fabric, and the this industries produce wastewater that can pollute the aquatic environment. Besides dyes, batik wastewater also contains synthetic compounds that are hard degraded, such as heavy metals, suspended solids, or organic compounds. In this study, photocatalitic membrane TiO2 coated plastic sheets have been used to degrade batik wastewater under solar exposure. A total of 8 pieces of catalyst sheets are added on 1000 ml of the waste, and managed to degrade 50.41% of the initial concentration during 5-days irradiation. In this study, several parameters of the water quality such as chemical oxygen demand (COD), biological oxygen demand (BOD), and total suspensed solids (TSS) of the wastewater were observed to be decreasing during photodegradation process. The catalyst sheet also is stable to be used repeatedly in wastewater treatment.

Non-biodegradable landfill leachate treatment by combined process of agitation, coagulation, SBR and filtration

Energy Technology Data Exchange (ETDEWEB)

Abood, Alkhafaji R. [State Key Laboratory of Biogeology and Environmental Geology, China University of Geosciences, Wuhan 430074 (China); Thi Qar University, Nasiriyah (Iraq); Bao, Jianguo, E-mail: bjianguo888@126.com [State Key Laboratory of Biogeology and Environmental Geology, China University of Geosciences, Wuhan 430074 (China); Du, Jiangkun; Zheng, Dan; Luo, Ye [State Key Laboratory of Biogeology and Environmental Geology, China University of Geosciences, Wuhan 430074 (China)

2014-02-15

Highlights: • A novel method of stripping (agitation) was investigated for NH{sub 3}-N removal. • PFS coagulation followed agitation process enhanced the leachate biodegradation. • Nitrification–denitrification achieved by changing operation process in SBR treatment. • A dual filter of carbon-sand is suitable as a polishing treatment of leachate. • Combined treatment success for the complete treatment of non-biodegradable leachate. - Abstract: This study describes the complete treatment of non-biodegradable landfill leachate by combined treatment processes. The processes consist of agitation as a novel stripping method used to overcome the ammonia toxicity regarding aerobic microorganisms. The NH{sub 3}-N removal ratio was 93.9% obtained at pH 11.5 and a gradient velocity (G) 150 s{sup −1} within a five-hour agitation time. By poly ferric sulphate (PFS) coagulation followed the agitation process; chemical oxygen demand (COD) and biological oxygen demand (BOD{sub 5}) were removed at 70.6% and 49.4%, respectively at an optimum dose of 1200 mg L{sup −1} at pH 5.0. The biodegradable ratio BOD{sub 5}/COD was improved from 0.18 to 0.31 during pretreatment step by agitation and PFS coagulation. Thereafter, the effluent was diluted with sewage at a different ratio before it was subjected to sequencing batch reactor (SBR) treatment. Up to 93.3% BOD{sub 5}, 95.5% COD and 98.1% NH{sub 3}-N removal were achieved by SBR operated under anoxic–aerobic–anoxic conditions. The filtration process was carried out using sand and carbon as a dual filter media as polishing process. The final effluent concentration of COD, BOD{sub 5}, suspended solid (SS), NH{sub 3}-N and total organic carbon (TOC) were 72.4 mg L{sup −1}, 22.8 mg L{sup −1}, 24.2 mg L{sup −1}, 18.4 mg L{sup −1} and 50.8 mg L{sup −1} respectively, which met the discharge standard. The results indicated that a combined process of agitation-coagulation-SBR and filtration effectively eliminated

Anthropogenic influence on surface water quality of the Nhue and Day sub-river systems in Vietnam.

Science.gov (United States)

Hanh, Pham Thi Minh; Sthiannopkao, Suthipong; Kim, Kyoung-Woong; Ba, Dang The; Hung, Nguyen Quang

2010-06-01

In order to investigate the temporal and spatial variations of 14 physical and chemical surface water parameters in the Nhue and Day sub-river systems of Vietnam, surface water samples were taken from 43 sampling sites during the dry and rainy seasons in 2007. The results were statistically examined by Mann-Whitney U-test and hierarchical cluster analysis. The results show that water quality of the Day River was significantly improved during the rainy season while this was not the case of the Nhue River. However, the river water did not meet the Vietnamese surface water quality standards for dissolved oxygen (DO), biological oxygen demand (BOD(5)), chemical oxygen demand (COD), nutrients, total coliform, and fecal coliform. This implies that the health of local communities using untreated river water for drinking purposes as well as irrigation of vegetables may be at risk. Forty-three sampling sites were grouped into four main clusters on the basis of water quality characteristics with particular reference to geographic location and land use and revealed the contamination levels from anthropogenic sources.

Fenceline water quality monitoring of effluents from BARC establishment

International Nuclear Information System (INIS)

Prathibha, P.; Kothai, P.; Saradhi, I.V.; Pandit, G.G.; Puranik, V.D.

2007-01-01

Wastewater generated from various sources (industrial, residential, rain water runoff etc.,) is either discharged into water bodies or reused/recycled for various purposes. Continuous monitoring of the wastewater is necessary to check whether these effluents are meeting the stringent limits proposed for discharge into water bodies or recycled/reused. Monitoring of these effluents also helps in designing the wastewater treatment system required to meet the standards. In this paper, water quality monitoring carried out during each quarter of the year 2005 for the effluents discharged from different utilities of BARC into Trombay bay is presented. The results indicate that the Bio-chemical oxygen demand (BOD) and chemical oxygen demand (COD) are in the range of 7.9 to 38.9 mg/l and 29.4 to 78.9 mg/l respectively. The nitrates and sulphates are in the range of 0.5 to 7.2 mg/l and 7.8 to 52.3 mg/l respectively. The water quality data of the parameters analyzed are well within the limits stipulated by Central Pollution Control Board. (author)

Distribution of Fish in the Upper Citarum River: an Adaptive Response to Physico-Chemical Properties

Directory of Open Access Journals (Sweden)

SUNARDI

2012-12-01

Full Text Available Distribution of fish in river is controlled by physico-chemical properties of the water which is affected by land-use complexity and intensity of human intervention. A study on fish distribution was carried out in the upper Citarum River to map the effects of physio-chemical properties on habitat use. A survey was conducted to collect fish and to measure the water quality both on dry and rainy season. The result showed that distribution of the fish, in general, represented their adaptive response to physico-chemical properties. The river environment could be grouped into two categories: (i clean and relatively unpolluted sites, which associated with high DO and water current, and (ii polluted sites characterized by low DO, high COD, BOD, water temperature, NO3, PO4, H2S, NH3, and surfactant. Fish inhabiting the first sites were Xiphophorus helleri, Punctius binotatus, Xiphophorus maculatus, and Oreochromis mossambicus. Meanwhile, the latter sites were inhabited by Liposarcus pardalis, Trichogaster trichopterus, and Poecilia reticulata. Knowledge about fish distribution in association with the pysico-chemical properties of water is crucial especially for the river management.

Integrating the Fenton's Process with Biofiltration by to Reduce Chemical Oxygen Demand of Winery Effluents.

Science.gov (United States)

Pipolo, Marco; Martins, Rui C; Quinta-Ferreira, Rosa M; Costa, Raquel

2017-03-01

The discharge of poorly decontaminated winery wastewater remains a serious environmental problem in many regions, and the industry is welcoming improved treatment methods. Here, an innovative decontamination approach integrating Fenton's process with biofiltration by Asian clams is proposed. The potential of this approach was assessed at the pilot scale using real effluent and by taking an actual industrial treatment system as a benchmark. Fenton peroxidation was observed to remove 84% of the effluent's chemical oxygen demand (COD), reducing it to 205 mg L. Subsequent biofiltration decreased the effluent's COD to approximately zero, well below the legal discharge limit of 150 mg L, in just 3 d. The reduction of the effluent's organic load through Fenton's process did not decrease its toxicity toward , but the effluent was much less harmful after biofiltration. The performance of the treatment proposed exceeded that of the integrated Fenton's process-sequencing batch reactor design implemented in the winery practice, where a residence time of around 10 d in the biological step typically results in 80 to 90% of COD removal. The method proposed is effective and compatible with typical winery budgets and potentially contributes to the management of a nuisance species. Copyright © by the American Society of Agronomy, Crop Science Society of America, and Soil Science Society of America, Inc.

KEMAMPUAN SISTEM SARINGAN PASIR-TANAMAN MENURUNKAN NILAI BOD DAN COD AIR TERCEMAR LIMBAH PENCELUPAN

Directory of Open Access Journals (Sweden)

I W. Budiarsa Suyasa

2012-11-01

Full Text Available Colored of clothes has developed as concentrated in Denpasar area. The process has a negativeeffect because of waste, the resulting organic toxicants and heavy metal into aquatic system. The effect ofthe pollution including the river, well water and organism that live there. The research of bioremedialeffectiveness of herb-sand treatment system on laboratory simulation were studied in Denpasar, from June2004 to September 2004.For laboratory simulation, the plants were cultured in 25 cm sand bed, in between 5 cm palmfiber ofwhich were in between 10 cm pumicestone for the top and 5 cm gravel for the bottom with surface area of 25x 50 cm2.The result of treatment system showed that effective for decrease biological oxygen demandcompared to those of chemical oxygen demand parameters. The treatment system reduced significantly BODlevel respectively to 13,15 for 3 days, 11,19 for 10 days and 5,79 for 20 days with 85,55 – 93,63 effectively.While COD level respectively to 76,68 for 3 days, 61,38 for 10 days and 58,57 for 20 days with 42,78 – 56,50effectively. Time of treatment for 3, 10 and 20 days showed a little increase of pH from 6,87 to 7,00.

Environmental applications of manometric respirometric methods

Energy Technology Data Exchange (ETDEWEB)

Roppola, K.

2009-07-01

In this work a manometric respirometric measuring system was applied to practical environmental cases related to wastewater management and biodegradation studies of oil-contaminated soils and materials used in landfill structures. Pollution of groundwater, surface water and soils is a worldwide problem. Therefore, tests simulating the biodegradation behaviour of organic compounds in water media and soils have become increasingly important. Respirometric methods provide direct measurement of the oxygen consumed by micro-organisms in biodegradation processes from an air or oxygen-enriched environment in a closed vessel. Biochemical oxygen demand (BOD) is a crucial environmental parameter used to measure the quality of water and treatment results in wastewater. Generally, BOD is measured with standardised methods, which are usually time-consuming as well as laborious. In this work the manometric respirometric test was compared with conventional BOD tests by determining the BOD of pulp and paper mills as well as domestic wastewater samples. The effect of different factors such as type, amount and pre-treatment of inoculum and the effect of dilution of a sample on the BOD values were also tested. A right dilution was noticed to be the most significant factor affecting the BOD values of the industrial wastewater samples. The mathematic estimation of the BOD7 values from the respirometric data was proved to work reliably after a 2-3 day incubation period. Characterisation of organic fractions of the pulp and paper mill wastewater was carried out with methods including filtration, long term BOD measurements and COD analyses. The most significant observation in characterisation analyses was that a remarkable part of the detected oxygen demand was consumed for the biotransformation of biodegradable fractions into new inert decomposition products, not only for mineralisation of the biodegradable COD fraction. Biodegradation behaviour of the peat samples with different

Evaluation of selected wetland plants for removal of chromium from ...

African Journals Online (AJOL)

user

demand (COD), biochemical oxygen demand (BOD) and nitrogen under a 5 day hydraulic retention time were analyzed based on HACH manual. The Cr in the plant tissue was analyzed through .... measured for five days of hydraulic retention time (HRT) using a stopwatch and measuring cylinder (Figure 1). The wastewater ...

PENGOLAHAN LINDI DENGAN OZON DAN PROSES OKSIDASI LANJUT BERBASIS OZON

Directory of Open Access Journals (Sweden)

Mohamad Rangga Sururi

2014-05-01

Full Text Available Limbah industri tekstil di area pinggir kota Surabaya mempunyai karakteristik perbandingan COD dan BOD = 5.57. Limbah jenis ini sulit untuk dibiodegradasi. Studi ini mempelajari tekonologi elektrokoagulasi untuk mengolah limbah tekstil dengan menurunkan intensitas warna, Total Suspended Solid (TSS dan Chemical Oxygen Demand (COD. Percobaan batch pada suhu kamar dilakukan untuk mempelajari pengaruh pH, jarak elektroda terhadap penurunan warna,TSS dan COD dan membandingkan biaya operasinya jika menggunakan pengolahan kimia.Effisiensi penurunan tertinggi untuk warna (91.96%,  TSS (49.17%, dan COD (29.67% terjadi pada pH awal 4.0 dan jarak elektroda 2 cm dengan  elektroda Al/Al. Waktu optimum penurunan intensitas warna dalah 10 menit. Laju penurunan COD adalah : -dC/dt = 0.0053 C +0.056 , dengan C adalah konsentrasi COD. Jumlah sludge yang dihasilkan daripengolahan elektrokoagulasi  3.4 % lebih kecil dibandingkan menggunakan bahan kimia. Biaya yang digunakan untuk pengolahan dengan elektrokoagulasi 52.35 % lebih murah dibandingkan jika menggunakan koagulasi dengan bahan kimia ( tawas. Kata kunci : elektrokoagulasi, penurunan warna, penurunan TSS, laju degradasi COD, imbah tekstil Abstract Waste water from textile industry which is located in one suburb of Surabaya city as characteristic which the ratio of COD to BOD was 5.57. This type of waste water is difficult to be biodegraded. This study investigated elektrokoagulasi technology to treat textile waste water by removing color, total suspended solid, and Chemical Oxygen Demand. Batch experiment at room temperature was carried out to study the effect of pH, electrode distance for color, TSS and COD removal. This study also tried to compare the operation cost between elektrokoagulasi and chemical processes. The best removal efficiencies by Al electrodes was 91.96 % for color, 49.17 % for TSS and 29.67 % for COD which were under initial pH 4.0 and electrodes distance 2 cm. The optimum operation

PENGOLAHAN PRIMER LIMBAH TEKSTIL DENGAN ELEKTROKOAGULASI

Directory of Open Access Journals (Sweden)

Lieke Riadi

2014-12-01

Full Text Available Limbah industri tekstil di area pinggir kota Surabaya mempunyai karakteristik perbandingan COD dan BOD = 5.57. Limbah jenis ini sulit untuk dibiodegradasi. Studi ini mempelajari tekonologi elektrokoagulasi untuk mengolah limbah tekstil dengan menurunkan intensitas warna, Total Suspended Solid (TSS dan Chemical Oxygen Demand (COD. Percobaan batch pada suhu kamar dilakukan untuk mempelajari pengaruh pH, jarak elektroda terhadap penurunan warna,TSS dan COD dan membandingkan biaya operasinya jika menggunakan pengolahan kimia.Effisiensi penurunan tertinggi untuk warna (91.96%,  TSS (49.17%, dan COD (29.67% terjadi pada pH awal 4.0 dan jarak elektroda 2 cm dengan  elektroda Al/Al. Waktu optimum penurunan intensitas warna dalah 10 menit. Laju penurunan COD adalah : -dC/dt = 0.0053 C +0.056 , dengan C adalah konsentrasi COD. Jumlah sludge yang dihasilkan daripengolahan elektrokoagulasi  3.4 % lebih kecil dibandingkan menggunakan bahan kimia. Biaya yang digunakan untuk pengolahan dengan elektrokoagulasi 52.35 % lebih murah dibandingkan jika menggunakan koagulasi dengan bahan kimia ( tawas. Kata kunci : elektrokoagulasi, penurunan warna, penurunan TSS, laju degradasi COD, imbah tekstil Abstract Waste water from textile industry which is located in one suburb of Surabaya city as characteristic which the ratio of COD to BOD was 5.57. This type of waste water is difficult to be biodegraded. This study investigated elektrokoagulasi technology to treat textile waste water by removing color, total suspended solid, and Chemical Oxygen Demand. Batch experiment at room temperature was carried out to study the effect of pH, electrode distance for color, TSS and COD removal. This study also tried to compare the operation cost between elektrokoagulasi and chemical processes. The best removal efficiencies by Al electrodes was 91.96 % for color, 49.17 % for TSS and 29.67 % for COD which were under initial pH 4.0 and electrodes distance 2 cm. The optimum operation

489 SEASONAL VARIATION IN PHYSICO-CHEMICAL ...

African Journals Online (AJOL)

Osondu

higher concentration during the wet season than in the dry season in all the Groups, except for BOD, sulphate and iron. ... availability and quality of groundwater due to waste and ... using 1 litre plastic containers that were treated with 3-4ml of ...

Physico-chemical analysis of ground water samples of coastal areas of south Chennai in the post-Tsunami scenario.

Science.gov (United States)

Rajendran, A; Mansiya, C

2015-11-01

The study of changes in ground water quality on the east coast of chennai due to the December 26, 2004 tsunami and other subsequent disturbances is a matter of great concern. The post-Tsunami has caused considerable plant, animal, material and ecological changes in the entire stretch of chennai coastal area. Being very close to sea and frequently subjected to coastal erosion, water quality has been a concern in this coastal strip, and especially after the recent tsunami this strip seems to be more vulnerable. In the present investigation, ten ground water samples were collected from various parts of south chennai coastal area. Physico-chemical parameters such as pH, temperature, Biochemical oxygen demand (BOD), Dissolved oxygen (DO), total solids; turbidity and fecal coliform were analyzed. The overall Water quality index (WQI) values for all the samples were found to be in the range of 68.81-74.38 which reveals a fact that the quality of all the samples is only medium to good and could be used for drinking and other domestic uses only after proper treatment. The long term adverse impacts of tsunami on ground water quality of coastal areas and the relationships that exist and among various parameters are carefully analyzed. Local residents and corporation authorities have been made aware of the quality of their drinking water and the methods to conserve the water bodies. Copyright © 2015 Elsevier Inc. All rights reserved.

Untitled

African Journals Online (AJOL)

surface-water problem, affecting both which is the main tributary of the River running and still water demanding special. Gibe. Such waste discharge without any attention (2). form of treatment not only becomes a. The 5-day Biological Oxygen. Demand (BOD) is the best single strength potential health hazard to the nearby.

The use of Moringa oleifera seed as a natural coagulant for wastewater treatment and heavy metals removal

Science.gov (United States)

Shan, Tan Chu; Matar, Manaf Al; Makky, Essam A.; Ali, Eman N.

2017-06-01

Moringa oleifera (MO) is a multipurpose tree with considerable potential and its cultivation is currently being actively promoted in many developing countries. Seeds of this tropical tree contain water-soluble, positively charged proteins that act as an effective coagulant for water and wastewater treatment. Based on this, water quality of "Sungai baluk" river was examined before and after the treatment using MO seed. MO seed exhibited high efficiency in the reduction and prevention of the bacterial growth in both wastewater and "Sungai baluk" river samples. The turbidity was removed up to 85-94% and dissolved oxygen (DO) was improved from 2.58 ± 0.01 to 4.00 ± 0.00 mg/L. The chemical oxygen demand (COD) and biological oxygen demand (BOD) were increased after the treatment from 99.5 ± 0.71 to 164.0 ± 2.83 mg/L for COD and from 48.00 ± 0.42 to 76.65 ± 2.33 mg/L for BOD, respectively. Nevertheless, there was no significant alteration of pH, conductivity, salinity and total dissolved solid after the treatment. Heavy metals such as Fe were fully eliminated, whereas Cu and Cd were successfully removed by up to 98%. The reduction of Pb was also achieved by up to 78.1%. Overall, 1% of MO seed cake was enough to remove heavy metals from the water samples. This preliminary laboratory result confirms the great potential of MO seed in wastewater treatment applications.

Assessment of On-Site Treatment Process of Institutional Building’s Wastewater

Directory of Open Access Journals (Sweden)

Motasem N. Saidan

2018-03-01

Full Text Available This study is conducted to investigate the characteristics of outflow wastewater of the 1 m3 on-site wastewater treatment unit on the basis of the testing and measurement data of the samples that were taken during the study monitored period (August 2017 to January 2018. For this purpose, samples were taken on a weekly basis from the treated wastewater effluent and five quality parameters (biochemical oxygen demand (BOD, chemical oxygen demand (COD, total suspended solids (TSS, pH, E-coli counts were monitored and measured. The average values of the five parameters were compared with the Jordanian standard maximum values, and water reuse in irrigation of plants classifications have been assessed and investigated. Average values of BOD, COD, TSS, pH, and E-coli in treated wastewater were 11 mg/L, 104 mg/L, 15 mg/L, 7.51, and 387 counts, respectively. The installation of in-line ultraviolet (UV unit in recirculating delivery system played a vital role in the reduction of counts far below the permissible maximum level (1000 counts. Based on national and international standards and criteria, results showed that the treated wastewater is suitable for the irrigation of two classifications of plants: (i Fruit trees, road-green sides outside cities, and green landscape; (ii Crops, commercial crops, and forest trees. Hence, such very low water flow rate treatment system can be utilized in refugees’ camps and water scarce residential areas in Jordan.

Sewage treatment in integrated system of UASB reactor and duckweed pond and reuse for aquaculture.

Science.gov (United States)

Mohapatra, D P; Ghangrekar, M M; Mitra, A; Brar, S K

2012-06-01

The performance of a laboratory-scale upflow anaerobic sludge blanket (UASB) reactor and a duckweed pond containing Lemna gibba was investigated for suitability for treating effluent for use in aquaculture. While treating low-strength sewage having a chemical oxygen demand (COD) of typically less than 200 mg/L, with an increase in hydraulic retention time (HRT) from 10.04 to 33.49 h, COD removal efficiency of the UASB reactor decreased owing to a decrease in organic loading rate (OLR) causing poor mixing in the reactor. However, even at the lower OLR (0.475 kg COD/(m3 x d)), the UASB reactor gave a removal efficiency of 68% for COD and 74% for biochemical oxygen demand (BOD). The maximum COD, BOD, ammonia-nitrogen and phosphate removal efficiencies of the duckweed pond were 40.77%, 38.01%, 61.87% and 88.57%, respectively. Decreasing the OLR by increasing the HRT resulted in an increase in efficiency of the duckweed pond for removal of ammonia-nitrogen and phosphate. The OLR of 0.005 kg COD/(m2 x d) and HRT of 108 h in the duckweed pond satisfied aquaculture quality requirements. A specific growth rate of 0.23% was observed for tilapia fish fed with duckweed harvested from the duckweed pond. The economic analysis proved that it was beneficial to use the integrated system of a UASB reactor and a duckweed pond for treatment of sewage.

Performance evaluation of a full-scale ABS resin manufacturing wastewater treatment plant: a case study in Tabriz Petrochemical Complex

Directory of Open Access Journals (Sweden)

Mohammad Shakerkhatibi

2016-08-01

Full Text Available Background: The measurement data regarding the influent and effluent of wastewater treatment plant (WWTP provides a general overview, demonstrating an overall performance of WWTP. Nevertheless, these data do not provide the suitable operational information for the optimization of individual units involved in a WWTP. A full-scale evolution of WWTP was carried out in this study via a reconciled data. Methods: A full-scale evolution of acrylonitrile, butadiene and styrene (ABS resin manufacturing WWTP was carried out. Data reconciliation technique was employed to fulfil the mass conservation law and also enhance the accuracy of the flow measurements. Daily average values from long-term measurements by the WWTP library along with the results of four sampling runs, were utilized for data reconciliation with further performance evaluation and characterization of WWTP. Results: The full-scale evaluation, based on balanced data showed that removal efficiency based on chemical oxygen demand (COD and biochemical oxygen demand (BOD5 through the WWTP were 80% and 90%, respectively, from which only 28% of COD and 20% of BOD5 removal had occurred in biological reactor. In addition, the removal efficiency of styrene and acrylonitrile, throughout the plant, was approximately 90%. Estimation results employing Toxchem model showed that 43% of acrylonitrile and 85% of styrene were emitted into the atmosphere above water surfaces. Conclusion: It can be concluded that the volatilization of styrene and acrylonitrile is the main mechanism for their removal along with corresponded COD elimination from the WWTP.

Aromatic chemical feedstocks from coal

Energy Technology Data Exchange (ETDEWEB)

Collin, G

1982-06-01

Liquid byproducts of coal carbonization meet some 25% of the world demand for aromatic chemicals, currently at approx. 30 million t/a, in particular 15% of the demand for benzene and over 95% of the demand for condensed aromatics and heteroaromatics. Industrial processing of the aromatic byproducts of coal pressure gasification is carried out to only a minor extent. Other methods that may be employed in future to obtain carbochemical aromatic compounds are solvolysis and supercritical gas extraction, the catalytic liquid-phase hydrogenation and hydropyrolysis of coal, which also permit recovery of benzene and homologues, phenols, and condensed and partially hydrogenated aromatics, and the synthesis of aromatics using methanol as the key compound. As with the present means of obtaining aromatic chemicals from coal, the processes that may in the future be applied on an industrial scale to obtain pure aromatics will only be economically feasible if linked with the manufacture of other mass products and combined with the present production of carbochemical aromatics.

Quality analysis of effluents from biodigesters in lodges located in the Cuyabeno Wildlife Reserve

Directory of Open Access Journals (Sweden)

Isidro Gutiérrez Cruz

2016-09-01

Full Text Available In the Cuyabeno Wildlife Reserve near Laguna Grande and Cuyabeno river, several ecological hotels have been built to meet the touristic demand; therefore these eco-lodges generate wastewaters. The Ministry of Environment, responsible for biodiversity conservation, has ordered the implementation of biodigesters for the treatment of these waters. After three years of implementing the system, it is proposed to check the quality of these waters, through the analysis of physical-chemical parameters: temperature, conductivity, pH, sulfates, nitrates and nitrites, detergents, COD, BOD5, oils and fats; and microbiological such as faecal coliforms. These results were compared with the current environmental legislation: TULSMA "Limits discharged to a body of fresh water." Sampling was subject to the provisions of standard Regulation INEN 2 169: 2013 and sampled at the time of high and low rainfall. The results determined that biodigesters only meet the standard regulations in three parameters: nitrates and nitrites; sulfates and temperature; and violate the following regulations: BOD5, COD and pH; while in the remaining four parameters, there is a variation among the results. In conclusion all digesters violate the regulations, at least on one of the parameters.

Just add water: reproducible singly dispersed silver nanoparticle suspensions on-demand

International Nuclear Information System (INIS)

MacCuspie, Robert I.; Allen, Andrew J.; Martin, Matthew N.; Hackley, Vincent A.

2013-01-01

Silver nanoparticles (AgNPs) are of interest due to their antimicrobial attributes, which are derived from their inherent redox instability and subsequent release of silver ions. At the same time, this instability is a substantial challenge for achieving stable long-term storage for on-demand use of AgNPs. In this study, we describe and validate a “just add water” approach for achieving suspensions of principally singly dispersed AgNPs. By lyophilizing (freeze drying) the formulated AgNPs into a solid powder, or cake, water is removed thereby eliminating solution-based chemical changes. Storing under inert gas further reduces surface reactions such as oxidation. An example of how to optimize a lyophilization formulation is presented, as well as example formulations for three AgNP core sizes. This “just add water” approach enables ease of use for the researcher desiring on-demand singly dispersed AgNP suspensions from a single master batch. Implementation of this methodology will enable studies to be performed over long periods of time and across different laboratories using particles that are identical chemically and physically and available on-demand. In addition, the approach of freeze drying and on-demand reconstitution by adding water has enabled the development of AgNP reference materials with the required shelf-life stability, one of the principal objectives of this research

Research on the sewage treatment in high altitude region based on Lhasa Sewage Treatment Plant

Science.gov (United States)

Xu, Jin; Li, Shuwen

2017-12-01

Sewage treatment is of great significance to enhance environmental quality, consolidate pollution prevention and ecological protection, and ensure sustainable economic and social development in high altitude region. However, there are numerous difficulties in sewage treatment due to the alpine climate, the relatively low economic development level, and the backward operation and management styles, etc. In this study, the characteristics of influent quality in the sewage treatment plant in Lhasa are investigated by analysing the influent BOD5/COD and BOD5/TN, comparing key indexes recorded from 2014 to 2016 with the hinterland. Results show that the concentration of influent COD, BOD5, NH3-N and SS in the Lhasa sewage treatment plant, in which the sewage belongs to low-concentration urban sewage, is smaller than that in the domestic sewage treatment plants in the mainland. The concentration ratio of BOD5/COD and BOD5/TN is below 0.4 and 4, which indicates that the biodegradation is poor and the carbon sources are in bad demand. The consequences obtained play a vital role in the design, operation and management of sewage treatment plants in high altitude region.

Aerobic co-treatment of landfill leachate and domestic wastewater - are slowly biodegradable organics removed or simply diluted?

Science.gov (United States)

Campos, R; Ferraz, F M; Vieira, E M; Povinelli, J

2014-01-01

This study investigated the co-treatment of landfill leachate/domestic wastewater in bench-scale activated sludge (AS) reactors to determine whether the slowly biodegradable organic matter (SBOM) was removed rather than diluted. The AS reactors were loaded with mixtures of raw leachate and leachate that was pretreated by air stripping. The tested volumetric ratios were 0%, 0.2%, 2% and 5%. For all of the tested conditions, the reactors performed better when pretreated leachate was used rather than raw leachate, and the best volumetric ratio was 2%. The following removals were obtained: 97% for the biochemical oxygen demand (BOD5,20), 79% for total suspended solids, 77% for dissolved organic carbon and 84% for soluble chemical oxygen demand. Most of the pretreated leachate SBOM (65%) was removed rather than diluted or adsorbed into the sludge, as confirmed by Fourier transform infrared (FTIR) spectroscopy analyses.

Investigation of Wastewater Pollution at Clan Jetty, Penang

Directory of Open Access Journals (Sweden)

Razak Fazilah Md

2014-01-01

Full Text Available This study aims to determine the level of wastewater pollution at Clan Jetty, Penang. 20 locations were chosen for water sampling around the jetties. Experiments were conducted to investigate the parameters, namely, temperature at each point, Chemical Oxygen Demand (COD, Biochemical Oxygen Demand (BOD, pH, Dissolved Oxygen (DO, the presence of Coliform and E. coli, Nitrate Nitrogen, Ammonical Nitrogen, Suspended Solids, Oil and Grease as well as Total Phosphorus (TP. Laboratory results showed that Point 1A was the most polluted location compared to other sampling points. The highest COD recording was 5824 mg/L at Point 1A and the lowest amount of 103 mg/L was recorded at Point 4. This study demonstrates that the absence of a sewerage system contributes to marine pollution around the jetties. Thus, a sewerage system is the best solution to improve water quality around the jetties in the future.

Utilization of Paper Sludge Wastes for Treatment of Wastewater from Food Processing Industries

Directory of Open Access Journals (Sweden)

Tohru Suzuki

2012-12-01

Full Text Available The food processing industries usually produced large amount of wastewater containing fine and small particles. It takes long time for complete settlement of the fine and small particles in the wastewater. The coagulation method appears to become one of the useful treatments. New inorganic coagulant named “Agoclean‒P” has been developed from paper sludge ash. The treatment by coagulation and flocculation were carried out for the wastewater from three different food processing industries namely soup, tofu, and natto. “Hi‒Biah‒System”, which is an in‒situ solidification system, was used for the continuous treatment of wastewater. The parameters for the water quality were pH, five‒day biochemical oxygen demand (BOD5, chemical oxygen demand (COD, total suspended solids (TSS, total nitrogen (TN and total phosphorus (TP. These parameters after the treatment became much lower values relative to those obtained before the treatment.

Solid and suspended/dissolved waste (N, P, O) from rainbow trout (Oncorynchus mykiss)

DEFF Research Database (Denmark)

Dalsgaard, Anne Johanne Tang; Pedersen, Per Bovbjerg

2011-01-01

differences between the dietary treatment groups in the waste produced. On average, 48% of the ingestedNwas recovered in thewater (TANconstituting 64–79%of this)and7% inthesolids. In comparison, 1% of the ingested P was recovered in the water and 43% in the solids. A breakpoint value of 5.6 g standardized......Quantifying aquaculture waste into different waste fractions will make it possible to design different treatment setups for obtaining specific cleaning objectives. The aim of this study was therefore to measure “all” solid and suspended/dissolved (i.e. unsedimented) waste from juvenile rainbow...... trout (Oncorynchus mykiss) fed three commonly applied commercial diets, “all” waste referring to: total nitrogen (N), total ammonia nitrogen (TAN=NH3-N+NH4-N), total phosphorus (P), and organicmatter characterized by the chemical oxygen demand (COD) and the biological oxygen demand after 5 days (BOD5...

Huge supply/demand increases seen in oxygenate forecasts

International Nuclear Information System (INIS)

Rhoades, A.K.

1992-01-01

Industry originally projected that oxygenate supply would not be able to meet the demand created by U.S. oxygenated and reformulated gasoline mandates. This paper reports that those projections have been reserved in two recent industry reports - one from Chemical Market Associates Inc. (CMAI) and one from Pace Consultants Inc. Pace's report, by Paulo Nery and Nathan Sims, predicts gasoline and oxygenates demand, and examines the role ethanol may play in changing those values. CMAI's report estimates captive supply and demand of butylenes and oxygenates. Oxygenates are entering the domestic gasoline market this winter as a result of the 1990 U.S. Clean Air Act Amendments. Methyl tertiary butyl ether (MTBE) is the most important oxygenate, although ethanol, ethyl tertiary butyl ether (ETBE), and tertiary amyl methyl ether (TAME) are gathering market strength. Ethanol's strength is derived from President Bush's ruling granting a waiver to reformulated gasoline containing ethanol. This waiver allows ethanol blends to have a vapor pressure 1 psi higher than other types of gasoline

Chemical oxygen demand removal efficiency and limited factors study of aminosilicone polymers in a water emulsion by iron-carbon micro-electrolysis.

Science.gov (United States)

Yang, Shangyuan; Liang, Zhiwei; Yu, Huadong; Wang, Yunlong; Chen, Yingxu

2014-02-01

Micro-electrolysis was applied in the present study to investigate the effect of pH, iron-carbon mass ratio, contact time, and treatment batch on the removal efficiency of chemical oxygen demand (COD) within an aminosilicone emulsion. The results exhibited that the removal efficiency of COD decreased linearly with the batch increase, and this tendency was consistent under the various conditions. The adsorption of activated carbons contributes a large portion to the elimination of COD within the aminosilicone emulsion. The oxidation action of iron-carbon micro-electrolysis was proven and the aminosilicone emulsion's COD removal contribution was approximately 16%. Aminosilicone polymers were adsorbed on the surface of activated carbons and iron chips, which contributes to the decline of COD removal efficiency and limits the contribution of oxidation action.

Assessment of Water Quality Index and Heavy Metal Contamination in Active and Abandoned Iron Ore Mining Sites in Pahang, Malaysia

Directory of Open Access Journals (Sweden)

Madzin Zafira

2017-01-01

Full Text Available The composition of heavy metals in water and surface soils of iron ore mining sites were investigated to evaluate on the potential occurrence of heavy metal contamination. Physico-chemical characteristics of the waters were also investigated to determine the current status of water quality index (WQI of the sites. Samples of water and surface soils of active mine (Kuala Lipis and abandoned mine (Bukit Ibam in Pahang were collected at four locations, respectively. The physico-chemical parameters measured for WQI were pH, dissolved oxygen, biological oxygen demand (BOD, chemical oxygen demand (COD, suspended solids (SS, and ammoniacal nitrogen (AN. The water quality parameters were classified according to the Department of Environment (DOE water quality classification. The study revealed that most of the sites in Bukit Ibam and Kuala Lipis were categorized as clean to slightly polluted. On the other hand, heavy metal analysis in water showed that aluminium and manganese level in both sites have exceeded the allowable limits for raw and treated water standards by the Ministry of Health. For heavy metal compositions in soils showed most of the heavy metal concentrations were below the recommended guideline values except for lead, arsenic, zinc and copper.

China's Coal: Demand, Constraints, and Externalities

Energy Technology Data Exchange (ETDEWEB)

Aden, Nathaniel; Fridley, David; Zheng, Nina

2009-07-01

future coal consumption is likely to come from the burgeoning coal-liquefaction and chemicals industries. If coal to chemicals capacity reaches 70 million tonnes and coal-to-liquids capacity reaches 60 million tonnes, coal feedstock requirements would add an additional 450 million tonnes by 2025. Even with more efficient growth among these drivers, China's annual coal demand is expected to reach 3.9 to 4.3 billion tonnes by 2025. Central government support for nuclear and renewable energy has not reversed China's growing dependence on coal for primary energy. Substitution is a matter of scale: offsetting one year of recent coal demand growth of 200 million tonnes would require 107 billion cubic meters of natural gas (compared to 2007 growth of 13 BCM), 48 GW of nuclear (compared to 2007 growth of 2 GW), or 86 GW of hydropower capacity (compared to 2007 growth of 16 GW). Ongoing dependence on coal reduces China's ability to mitigate carbon dioxide emissions growth. If coal demand remains on a high growth path, carbon dioxide emissions from coal combustion alone would exceed total US energy-related carbon emissions by 2010. Within China's coal-dominated energy system, domestic transportation has emerged as the largest bottleneck for coal industry growth and is likely to remain a constraint to further expansion. China has a low proportion of high-quality reserves, but is producing its best coal first. Declining quality will further strain production and transport capacity. Furthermore, transporting coal to users has overloaded the train system and dramatically increased truck use, raising transportation oil demand. Growing international imports have helped to offset domestic transport bottlenecks. In the long term, import demand is likely to exceed 200 million tonnes by 2025, significantly impacting regional markets.

Comparative Analysis on Chemical Composition of Bentonite Clays ...

African Journals Online (AJOL)

2017-09-12

Sep 12, 2017 ... Comparative Analysis on Chemical Composition of Bentonite Clays. Obtained from Ashaka and ... versatile material for geotechnical engineering and as well as their demand for ..... A PhD thesis submitted to the Chemical ...

Demand Uncertainty

DEFF Research Database (Denmark)

Nguyen, Daniel Xuyen

This paper presents a model of trade that explains why firms wait to export and why many exporters fail. Firms face uncertain demands that are only realized after the firm enters the destination. The model retools the timing of uncertainty resolution found in productivity heterogeneity models....... This retooling addresses several shortcomings. First, the imperfect correlation of demands reconciles the sales variation observed in and across destinations. Second, since demands for the firm's output are correlated across destinations, a firm can use previously realized demands to forecast unknown demands...... in untested destinations. The option to forecast demands causes firms to delay exporting in order to gather more information about foreign demand. Third, since uncertainty is resolved after entry, many firms enter a destination and then exit after learning that they cannot profit. This prediction reconciles...

Chapter A7. Section 7.0. Five-Day Biochemical Oxygen Demand

Science.gov (United States)

Delzer, Gregory C.; McKenzie, Stuart W.

1999-01-01

The presence of a sufficient concentration of dissolved oxygen is critical to maintaining the aquatic life and aesthetic quality of streams and lakes. Determinng how organic matter affects the concentration of dissolved oxygen (DO) in a stream or lake is integral to water-quality management. The decay of organic matter in water is measured as biochemical or chemical oxygen demand. This report describes the field protocols used by U.S. Geological Survey (USGS) personnel to determine the five-day test for biochemical oxygen demand.

A yeast co-culture-based biosensor for determination of waste water contamination levels.

Science.gov (United States)

Yudina, N Yu; Arlyapov, V A; Chepurnova, M A; Alferov, S V; Reshetilov, A N

2015-10-01

Artificial microbial co-cultures were formed to develop the receptor element of a biosensor for assessment of biological oxygen demand (BOD). The co-cultures possessed broad substrate specificities and enabled assays of water and fermentation products within a broad BOD range (2.4-80 mg/dm(3)) with a high correlation to the standard method (R = 0.9988). The use of the co-cultures of the yeasts Pichia angusta, Arxula adeninivorans and Debaryomyces hansenii immobilized in N-vinylpyrrolidone-modified poly(vinyl alcohol) enabled developing a BOD biosensor possessing the characteristics not inferior to those in the known biosensors. The results are indicative of a potential of using these co-cultures as the receptor element base in prototype models of instruments for broad application. Copyright © 2015 Elsevier Inc. All rights reserved.

Comparison of Chemical and Physical-chemical Wastewater Discoloring Methods

Directory of Open Access Journals (Sweden)

Durašević, V.

2007-11-01

Full Text Available Today's chemical and physical-chemical wastewater discoloration methods do not completely meet demands regarding degree of discoloration. In this paper discoloration was performed using Fenton (FeSO4 . 7 H2O + H2O2 + H2SO4 and Fenton-like (FeCl3 . 6 H2O + H2O2 + HCOOH chemical methods and physical-chemical method of coagulation/flocculation (using poly-electrolyte (POEL combining anion active coagulant (modified poly-acrylamides and cationic flocculant (product of nitrogen compounds in combination with adsorption on activated carbon. Suitability of aforementioned methods was investigated on reactive and acid dyes, regarding their most common use in the textile industry. Also, investigations on dyes of different chromogen (anthraquinone, phthalocyanine, azo and xanthene were carried out in order to determine the importance of molecular spatial structure. Oxidative effect of Fenton and Fenton-like reagents resulted in decomposition of colored chromogen and high degree of discoloration. However, the problem is the inability of adding POEL in stechiometrical ratio (also present in physical-chemical methods, when the phenomenon of overdosing coagulants occurs in order to obtain a higher degree of discoloration, creating a potential danger of burdening water with POEL. Input and output water quality was controlled through spectrophotometric measurements and standard biological parameters. In addition, part of the investigations concerned industrial wastewaters obtained from dyeing cotton materials using reactive dye (C. I. Reactive Blue 19, a process that demands the use of vast amounts of electrolytes. Also, investigations of industrial wastewaters was labeled as a crucial step carried out in order to avoid serious misassumptions and false conclusions, which may arise if dyeing processes are only simulated in the laboratory.

River water quality assessment using environmentric techniques: case study of Jakara River Basin.

Science.gov (United States)

Mustapha, Adamu; Aris, Ahmad Zaharin; Juahir, Hafizan; Ramli, Mohammad Firuz; Kura, Nura Umar

2013-08-01

Jakara River Basin has been extensively studied to assess the overall water quality and to identify the major variables responsible for water quality variations in the basin. A total of 27 sampling points were selected in the riverine network of the Upper Jakara River Basin. Water samples were collected in triplicate and analyzed for physicochemical variables. Pearson product-moment correlation analysis was conducted to evaluate the relationship of water quality parameters and revealed a significant relationship between salinity, conductivity with dissolved solids (DS) and 5-day biochemical oxygen demand (BOD5), chemical oxygen demand (COD), and nitrogen in form of ammonia (NH4). Partial correlation analysis (r p) results showed that there is a strong relationship between salinity and turbidity (r p=0.930, p=0.001) and BOD5 and COD (r p=0.839, p=0.001) controlling for the linear effects of conductivity and NH4, respectively. Principal component analysis and or factor analysis was used to investigate the origin of each water quality parameter in the Jakara Basin and identified three major factors explaining 68.11 % of the total variance in water quality. The major variations are related to anthropogenic activities (irrigation agricultural, construction activities, clearing of land, and domestic waste disposal) and natural processes (erosion of river bank and runoff). Discriminant analysis (DA) was applied on the dataset to maximize the similarities between group relative to within-group variance of the parameters. DA provided better results with great discriminatory ability using eight variables (DO, BOD5, COD, SS, NH4, conductivity, salinity, and DS) as the most statistically significantly responsible for surface water quality variation in the area. The present study, however, makes several noteworthy contributions to the existing knowledge on the spatial variations of surface water quality and is believed to serve as a baseline data for further studies. Future

Evaluation of Ravi river water quality

International Nuclear Information System (INIS)

Ahmed, K.; Ali, W.

2000-01-01

Investigation from 1989 to 1998 on river Ravi pollution was carried out to study the effects of wastewater discharges on its water quality in relation to its various water use. The sources of pollution entering the river between Syphon (20 Km upstream) and Balloki Head works (75 Km downstream) includes Upper Chenab Canal (U.C.) which bring industrial effluents through Deg municipal swage from the city of Lahore. Investigation revealed that the flow in the river are highly variable with time during the year U.C. canal with a capacity of 220 m/sup 3//S at the tail and Qadiarabad (Q.B.) Link canal with a capacity of 410 m3/S are mainly responsible for higher flows during dry season. A desecrating trend has been observed in the D.O. Levels indicating increasing pollution. Over times D.O values are above 4 mg/l indicating recovery due to dilution biodegradation and aeration. An increasing trend has been observed in Biochemical Oxygen Demand (BOD), suspended solids, total dissolved solids and indicator organisms. Even with the discharges of pollutions from U.C. canal, Hudiara Nullah and city sewage, BOD at Balloki was unexpectedly low. It was investigated that because of pollution free Q.B. link canal which joins the river just before Balloki Head works makes the water diluted, which accounted for low BOD. Water of river Ravi meet the chemical water quality requirement for irrigation. However the water quality does not meet the coliform and faecal coliform criteria for most water use. (orig../A.B.)

0056suppl.doc

Indian Academy of Sciences (India)

Tuning the BODIPY Core for its Potential Use in DSSC: A Quantum Chemical Approach. Narendra Nath Ghosha, Md. Habiba, ... Dye. HOMO. LUMO. Donor. п. Acceptor. Anchor. Donor. п. Acceptor. Anchor. FLU-2,6-BOD. CAR-2,6-BOD. 28. 29. 39. 53. 52. 46. 26. 18. 18. 14. 8. 1. 1. 1. 1. 1. 1. 6. 6. 6. 6. 87. 87. 87. 87. 6. 6. 6. 6.

Determination of Physicals, Chemical, Biologicals and Radioactivity Parameters of Sediments and Water Samples of Seropan River of First Period

International Nuclear Information System (INIS)

Tri Rusmanto; Agus Taftazani

2007-01-01

Seropan river water quality as residential water resources can be controlled by physical, chemical, and biological parameters. The water quality with the parameters of temperature, suspended solid (SS), gross β radioactivity, hardwater, COD, BOD, Escherichia Coli have been experimentally conducted. The sediment and water samples have been taken at February and August 2006. Measurement result of Seropan river water quality showed that the temperature was 28°C, maximum SS was 48 mg/L, maximum pH was 6.8 maximum hardwater was 257.49 mg/L, maximum COD was 8 mg/L, maximum BOD was 4.9 mg/L, maximum bacteria E. coli > 2400 mpn/100 mL, maximum water gross β was 0.9071 Bq/L. All the parameters were lower than maximum permissible for water condition that decided by Governor of Yogyakarta Special Province No/214/Kpts/1991 and Public Health Minister of Republic of Indonesia Number 907/Menkes/SK/VlI/2002. Sediment sample can not be evaluated because it was not included yet in the river water quality natural radionuclides gamma transmitter identified in river water samples were Tl-208 and K-40. More element detected in sediment samples, they were, Tl-208, Ac-228, Ra-226, Pb-212, Pb-214, Bi-214, Ac-228, Ac-228 and of K-40. (author)

A new route of bioaugmentation by allochthonous and autochthonous through biofilm bacteria for soluble chemical oxygen demand removal of old leachate.

Science.gov (United States)

Alijani Ardeshir, Rashid; Rastgar, Sara; Peyravi, Majid; Jahanshahi, Mohsen; Shokuhi Rad, Ali

2017-10-01

Landfill leachate contains environmental pollutants that are generally resistant to biodegradation. In this study, indigenous and exogenous bacteria in leachate were acclimated in both biofilm and suspension forms to increase the removal of soluble chemical oxygen demand (SCOD). The bacteria from the leachate and sewage were acclimated to gradually increasing leachate concentration prepared using a reverse osmosis membrane over 28 days. The SCOD removal was measured aerobically or nominally anaerobically. Biofilms were prepared using different carrier media (glass, rubber, and plastic). The maximum SCOD removal in suspensions was 32% (anaerobic) and in biofilms was 39% (aerobic). In the suspension form, SCOD removal using acclimated bacteria from leachate and sewage anaerobically increased in comparison with the control (P technology using biofilms and acclimations can be an effective, inexpensive, and simple way to decrease SCOD in old landfill leachate.

The effect of different soil uses on the quality of spring water

Directory of Open Access Journals (Sweden)

Lilian Vilela Andrade Pinto

2012-09-01

Full Text Available Several factors are known to be responsible for the degradation of water quality in our Planet’s spring sources. The goal of this study was to evaluate the impact of different anthropogenic activities on physico-chemical and biological properties of five spring water located in Inconfidentes, Minas Gerais State, Brazil. Analytical results have demonstrated that water source protected by native vegetation had the highest quality in terms of color, turbidity, biological oxygen demand (BOD5, total phosphate, nitrate, dissolved oxygen (DO, fecal coliforms and thermo-tolerant coliforms. On the other hand, the water quality was negatively impacted by the lack of adequate agricultural practices, such as the use of chemical inputs, the nonexistence of fenced livestock grazing areas and residential sewage system which are considered to be indispensable practices to minimize the environmental impact of anthropogenic activities and to protect human health.

Career Opportunities in Chemistry and Chemical Engineering.

Science.gov (United States)

Glover, Trienne

This pamphlet discusses career and employment opportunities in chemical engineering. Necessary college preparation is described and median salaries by degree are tabulated. Nontraditional careers in chemistry are also described. Future demand for chemists and chemical engineers is projected to 1985 and the availability of jobs for women and…

Assessment of potential health impacts on surface water sources in Northern Nigeria

Directory of Open Access Journals (Sweden)

ZD Umar

2014-05-01

Full Text Available Northern Nigeria represents the most populous region in Nigeria and adequate water supply and sanitation typically leaves a lot to be desired in the region in order to prevent water related diseases to the vulnerable communities of the region. This research work was carried out in Kano state with specific emphasis on Tomas dam which is one of the largest dams established for multipurpose use in Nigeria. The research was aimed at evaluating Physico-chemical and Bacteriological quality of Tomas Dam in Kano State. 240 water samples from 5 sampling stations within eight months were analyzed for bacteriological and physico-chemical quality. The physico-chemical parameters indicated Biochemical Oxygen Demand (BOD and Water Current Speed results were not significantly different (P>0.05, while other physico-chemical parameters analyzed varied significantly (P<0.05. The study also revealed that Dissolved Oxygen (DO, BOD, Turbidity, and Nitrates recorded higher values than WHO and Federal Environmental Protection Agency, Nigeria (FEPA limits. Total aerobic bacterial counts (TBC and total coliform counts (TCC were determined using pour plate and Most Probable Number (MPN techniques. TBC and TCC were high and exceeded acceptable limits. Faecal coliforms, faecal Streptococciand Klebsiella species constituted 25% of the indicator organisms identified.The observed parameters indicated the Dam was contaminated with pathogenic bacteria. Variations in the weather conditions, animal and anthropogenic interferences were all directly or indirectly related to faecal contamination in the dam. Preventing indiscriminate faecal discharge close to the Dam and sufficient water treatment before consumption are of prime importance to public health as the dam was established for agricultural purposes. DOI: http://dx.doi.org/10.3126/ije.v3i2.10523 International Journal of the Environment Vol.3(2 2014: 125-136

The business case for transitioning to safer chemicals.

Science.gov (United States)

McFadden, Roger D

2011-01-01

Emerging domestic and international chemical regulations and a heightened consumer awareness of chemicals of concern in products is challenging American businesses to reevaluate and reconsider their approaches to supply chain management and product design. Some of these companies recognize business opportunities and are responding proactively with innovative strategies and tactics. This article describes steps that Staples Inc., the world's largest office products provider, is taking to meet demand for products that are safer and more sustainable. In trying to meet the demand for safer products, Staples faces significant barriers, including the complexity of supply chains, data gaps, and confidential business information. New collaborations between companies, government, and advocates, and improved tools and criteria for defining safer products enhance the ability of businesses, like Staples, to meet new consumer demands.

Demand and availability of chemical data for 'Project 90'

International Nuclear Information System (INIS)

Andersson, K.

1987-01-01

The safety analysis performed within 'Project 90' includes transport modeling for the near zone and geosphere by a probabilistic model as well as by the NAMSOL model. In a later stage a detailed geochemical modeling may also be performed within the project. For all these models, data are required. In this report the need for and availability of data of chemical nature is reviewed. For a non site-specific, probabilistic model, the necessary chemical data seem to be available. The main problem is to choose appropriate distributions of distribution coefficients (K d -values). For a site-specific modeling the choice of site will determine the data available. A large amount of data for the sites studied by SKB are available. However site specific data on the complex forming agents in groundwater are unavailable for some sites. Data for groundwater constituents and fission and activation products are available for a detailed geochemical model, except for complex forming constants for humic material in the groundwater. Thermodynamic data for actinides are available, although the amount and quality vary. For some engineering materials (cement, bentonite) available data do not allow a detailed geochemical modeling. The solubilities of the rock and minerals present are not as well known, although data do exist. If kinetic effects are to be considered the data are poorly known. The influence of colloid formation of the actinides has to be considered in some way in connection with the modeling. There is not enough data available on this topic. (author)

Removal of color and chemical oxygen demand using a coupled coagulation-electrocoagulation-ozone treatment of industrial wastewater that contains offset printing dyes

International Nuclear Information System (INIS)

Roa M, G.; Barrera D, C.; Balderas H, P.; Zaldumbide O, F.; Reyes P, H.; Bilyeu, B.

2014-01-01

Industrial offset printing processes generate wastewater with highly colored obtaining values of 5 x 10 6 Pt-Co units and great values of chemical oxygen demand (COD) 5.3 x 10 -5 mg L -1 . Thus, conventional technologies such as biologicals treatment fail in reaching the discharge limits. In this research, a sequential treatment was applied: coagulation with aluminum hydroxychloride (AHC), electrocoagulation with Al anodes and finally ozonation. Optimal conditions are found when adding 20 mg L -1 AHC, followed by electrocoagulation at 4 A for 50 min, and finally alkaline ozonation for 15 min, resulting in an overall color removal of 99.99% color and 99.35 COD. The sludge generated by the coagulation process was analyzed by scanning electron microscopy and energy dispersive X-ray (EDX) microanalysis. (Author)

Removal of color and chemical oxygen demand using a coupled coagulation-electrocoagulation-ozone treatment of industrial wastewater that contains offset printing dyes

Energy Technology Data Exchange (ETDEWEB)

Roa M, G.; Barrera D, C.; Balderas H, P.; Zaldumbide O, F. [Centro Conjunto de Investigacion en Quimica Sustentable UAEM-UNAM, Km 14.5 Carretera Toluca-Atlacomulco, 50200 San Cayetano-Toluca, Estado de Mexico (Mexico); Reyes P, H. [Universidad Autonoma del Estado de Mexico, Facultad de Quimica, Paseo Colon y Paseo Tollocan s/n, 50120 Toluca, Estado de Mexico (Mexico); Bilyeu, B., E-mail: groam@uaemex.mx [Xavier University of Louisiana, Department of Chemistry, 1 Drexel Drive, New Orleans, LA 70125 (United States)

2014-07-01

Industrial offset printing processes generate wastewater with highly colored obtaining values of 5 x 10{sup 6}Pt-Co units and great values of chemical oxygen demand (COD) 5.3 x 10{sup -5} mg L{sup -1}. Thus, conventional technologies such as biologicals treatment fail in reaching the discharge limits. In this research, a sequential treatment was applied: coagulation with aluminum hydroxychloride (AHC), electrocoagulation with Al anodes and finally ozonation. Optimal conditions are found when adding 20 mg L{sup -1} AHC, followed by electrocoagulation at 4 A for 50 min, and finally alkaline ozonation for 15 min, resulting in an overall color removal of 99.99% color and 99.35 COD. The sludge generated by the coagulation process was analyzed by scanning electron microscopy and energy dispersive X-ray (EDX) microanalysis. (Author)

COMPARATIVE PERFORMANCE OF SAND AND COCONUT SUBSTRATE IN URBAN WASTEWATER TREATMENT PERFORMANCES COMPAREES DU SABLE ET DU SUBSTRAT DE COCO EN TRAITEMENT D’EAUX RESIDUAIRES URBAINES

Directory of Open Access Journals (Sweden)

MARTINE KONE

2015-05-01

Full Text Available Urban wastewater has been treated by infiltration-percolation on sand and on coconut substrate, in order to highlight their comparative performance. The pilots were fed to the hydraulic loading rate of 40 L·m-2·d-1 during three days a week and kept at rest the next four days. Parameters are measured on an average sample of 24 hours taken on the output of each pilot at the end of the third day of treatment. The average removal efficiencies of chemical oxygen demand (COD were respectively, 94.8 and 39.61 % with the sand and the coconut substrate while the average yields of biochemical oxygen demand (BOD5 were 99.01 and 98.12 %. The results showed that the average removal efficiencies of fecal coliform bacteria were respectively, 98.8 and 91 %. Conductivities have increased by an average of 39.88 % with the sand and 4.65 % with coconut substrate.

Phytoremediation Potential of Duckweed (Lemna minor L.) On Steel Wastewater.

Science.gov (United States)

Saha, Priyanka; Banerjee, Angela; Sarkar, Supriya

2015-01-01

An eco-friendly and cost effective technique- phytoremediation was used to remediate contaminants from waste water. This study demonstrated that phytoremediation ability of duckweed (Lemna minor L.) to remove chloride, sulphate from Biological Oxygen Treatment (BOT) waste water of coke oven plant. The BOT water quality was assessed by analyzing physico-biochemical characters--pH, Biological oxygen demand (BOD), Chemical oxygen demand (COD), total dissolved solids (TDS) and elemental concentration. It was observed that an increase in pH value indicated an improvement of water quality. The experimental results showed that, duckweed effectively removed 30% chloride, 16% sulphate and 14% TDS from BOT waste water, which suggested its ability in phytoremediation for removal of chloride and sulphate from BOT waste water. A maximum increase of 30% relative growth rate of duckweed was achieved after 21 days of experiment. Thus, it was concluded that duckweed, an aquatic plant, can be considered for treatment of the effluent discharged from the coke oven plant.

Evaluation of electricity generation from lignin residue and biogas in cellulosic ethanol production.

Science.gov (United States)

Liu, Gang; Bao, Jie

2017-11-01

This study takes the first insight on the rigorous evaluation of electricity generation based on the experimentally measured higher heating value (HHV) of lignin residue, as well as the chemical oxygen demand (COD) and biological oxygen demand (BOD 5 ) of wastewater. For producing one metric ton of ethanol fuel from five typical lignocellulose substrates, including corn stover, wheat straw, rice straw, sugarcane bagasse and poplar sawdust, 1.26-1.85tons of dry lignin residue is generated from biorefining process and 0.19-0.27tons of biogas is generated from anaerobic digestion of wastewater, equivalent to 4335-5981kWh and 1946-2795kWh of electricity by combustion of the generated lignin residue and biogas, respectively. The electricity generation not only sufficiently meets the electricity needs of process requirement, but also generates more than half of electricity surplus selling to the grid. Copyright © 2017 Elsevier Ltd. All rights reserved.

Biological treatment of potato processing wastewater for red pigment production by immobilized cells of UV-irradiated monascus sp. in repeated batch

International Nuclear Information System (INIS)

Khalaf, S.A.

2004-01-01

Potato processing wastewater (PPW) was collected and analyzed for biological oxygen demand (BOD), chemical oxygen demand (COD), total suspended solids (TSS), total nitrogen and starch content. A fungal strain isolated from PPW identified as Monascus sp. PPW was evaluated for its ability to grow and produce red pigment, biomass and reduce the starch content of the ,PPW. Active UV-irradiated isolate of the above strain was obtained by exposing the parent strain to UV-radiation and coded Monascus. sp. PPW-UV7 and used as immobilized cell system for PPW treatment process in repeated batch fermentation. The immobilized cells (in sponge cubes) were able to reduce COD by about 85.7 %, with biomass production of 9.22 gl+ l and over productivity of red pigment of 2.6 gl+ 1 after 8 days fermentation (2 batches). The immobilized cells showed stability and viability for 8 batches (32 days) during the process treatment

Phytoremediation of industrial mines wastewater using water hyacinth.

Science.gov (United States)

Saha, Priyanka; Shinde, Omkar; Sarkar, Supriya

2017-01-02

The wastewater at Sukinda chromite mines (SCM) area of Orissa (India) showed high levels of toxic hexavalent chromium (Cr VI). Wastewater from chromium-contaminated mines exhibit potential threats for biotic community in the vicinity. The aim of the present investigation is to develop a suitable phytoremediation technology for the effective removal of toxic hexavalent chromium from mines wastewater. A water hyacinth species Eichhornia crassipes was chosen to remediate the problem of Cr (VI) pollution from wastewater. It has been observed that this plant was able to remove 99.5% Cr (VI) of the processed water of SCM in 15 days. This aquatic plant not only removed hexavalent Cr, but is also capable of reducing total dissolved solids (TDS), biological oxygen demand (BOD), chemical oxygen demand (COD), and other elements of water also. Large-scale experiment was also performed using 100 L of water from SCM and the same removal efficiency was achieved.

Comparative studies on the differently operated trains of the North-Budapest Wastewater Treatment Plant.

Science.gov (United States)

Jobbágy, A; Palkó, Gy; Weinpel, T; Makó, M

2012-01-01

In order to reduce the pollution load of the Danube, the North-Budapest Wastewater Treatment Plant has been upgraded to enhanced nitrogen removal by establishing a new activated sludge treatment line and modifying the existing unit for nitrification and denitrification. As both the influent flow rate and the influent chemical oxygen demand (COD), biological oxygen demand (BOD(5)) and total suspended solids (TSS) concentration levels remained far below the design values, setting one fourth of the reactor volume out of operation in the Old Line, and operating the nitrification reactor of the New Line with part-time aeration proved to be possible. Analytical data as well as simulation studies supported the advantage of the intermittent-aeration process in efficient N-removal. However, the lengths of the aerated periods have to be increased with decreasing temperature, and thereby effluent total nitrogen (TN) concentration can increase due to decreasing denitrification efficiency. Potential occurrence of low-dissolved oxygen (DO) bulking should be hindered through applying an efficient anoxic selector system.

Stensund wastewater aquaculture. Studies of key factors for its optimization

Energy Technology Data Exchange (ETDEWEB)

Guterstam, B.; Forsberg, L.E. [Stensund Ecological Center, Stensunds Fold Center, S-61991 Trosa (Sweden); Buczynska, A. [Faculty of Process and Environmental Engineering, Technical University of Lodz, 175 Wolczanska strasse, PL-90942 Lodz (Poland); Frelek, K. [Department of Analytical Chemistry, Medical University of Gdansk, Al. Gen. J. Hallera 107, PL-80416 Gdansk (Poland); Pilkaityte, R. [Natural Science Faculty, University of Klaipeda, LT-5813 Klaipeda (Lithuania); Reczek, L. [Department of Water Supply and Sewage Systems, Warsaw Agricultural University, 166 Nowoursynowska strasse, PL-02787 Warsaw (Poland); Rucevska, I. [Latvian Environmental Data Center, Straumes 2, Jurmala LV 2015 (Latvia)

1998-10-21

This paper is a summary of an in-depth study of key factors in the function of a 7-year-old aquaculture system designed for treatment and recycling of domestic wastewater at Stensund, Trosa, Sweden. The reported areas are: wastewater flows, reduction of biochemical oxygen demand (BOD), chemical oxygen demand (COD), phosphorus, nitrogen, and fecal bacteria. Plant production is recorded as harvested biomass, and energy results are given as generated heat and electricity consumption. Special studies were conducted on the reduction of copper by anaerobic treatment. Nitrification was studied with different filter media. Microalgal autofocculation of phosphorus was studied in relation to pH and water hardness for the green algal genus Scenedesmus. Limiting factors for the growth of Daphnia magna in the zooplankton step of the constructed aquatic food-web was studied in a specially designed reproduction test. The results are analyzed in order to optimize the function of the wastewater aquaculture

Pollution from tanneries effluents and its impact on environment

International Nuclear Information System (INIS)

Rajput, A.A.; Memon, Hafeez-ur-Rahman; Sahto, M.H.

1999-01-01

The disposal of tanneries effluence has become one of the serious environmental problems. The effluents from tanneries contain highly toxic materials, including chromium salts, ammonium salts, acids, sodium sulphide and suspended solids. Hair, alkalinity, surfactants, dyes and oils are also present in these effluents. The extent of pollution depends upon the volume of the effluent discharged. Many studies have been carried out on the characteristics of these effluents in order to understand the nature of the effluents and their impact on environment. The present study shows measured values of different parameters like Biochemical Oxygen Demand (BOD) about 1950 mg/l, Chemical Oxygen Demand (COD) about 4500-4600 mg/l, suspended solids about 2600-2700 mg/l, dissolved solids 10000-12000 mg/l and lead, copper, chromium and cadmium about 2, 0.4, 64.4 and 0.31 mg/l respectively. The measured values are compared with that of previous. Some remedial measures for its treatment and disposal are also discussed. (author)

Characterization and correlations of various pollution parameters in the tannery effluent

International Nuclear Information System (INIS)

Haydar, S.

2008-01-01

Wastewater characterization is an integral part of treatment and management strategies for industrial effluents. This paper outlines the results of detailed wastewater characterization studies conducted for a tannery in Sheikhupura, Punjab. The results of this study demonstrated that the composition of tannery wastewater could change continuously due to inherent nature of tannery operations. In general, tannery effluent was alkaline in nature and highly polluted in terms of organic, solids, sulfates, sulfides and chromium content. Basic ingredients of tannery effluent i.e. high alkalinity and substantial portions of BOD (Biochemical Oxygen Demand), COD (Chemical Oxygen Demand) and other pollutants in particulate form rendered it suitable for enhanced pollutant removals at primary stage of treatment using suitable coagulants. Results of primary treatment of wastewater from this tannery suggested that primary treatment alone was not capable of reducing pollutant loads significantly. Hence post-primary biological treatment was required to meet local effluent quality standards. (author)

Characterization and study of correlations among major pollution parameters in textile wastewater

International Nuclear Information System (INIS)

Hyder, S.; Bari, A.

2011-01-01

Wastewater characterization is an integral part of treatment and management strategies for industrial effluents. This paper outlines the results of detailed wastewater characterization studies conducted for a textile mill in Lahore, Punjab. The results of this study demonstrated that the composition of textile wastewater could change continuously due to inherent nature of textile operations. In general, textile wastewater was high in temperature and alkaline in nature. It was highly polluted in terms of solids and organic content. Most of the portion of solids and organic load was in the soluble form. On the basis of mean values, temperature, pH, TDS (Total Dissolved Solids), BOD (Biochemical Oxygen Demand) and COD (Chemical Oxygen Demand) were above the limits set by NEQS (National Environmental Quality Standards) while chlorides and sulfates were below the limits set by NEQS. Prior neutralization of wastewater with an acid and addition of phosphorus and nitrogen is imperative for its effective treatment. (author)

Phytoremediation of industrial mines wastewater using water hyacinth

Science.gov (United States)

Saha, Priyanka; Shinde, Omkar; Sarkar, Supriya

2017-01-01

ABSTRACT The wastewater at Sukinda chromite mines (SCM) area of Orissa (India) showed high levels of toxic hexavalent chromium (Cr VI). Wastewater from chromium-contaminated mines exhibit potential threats for biotic community in the vicinity. The aim of the present investigation is to develop a suitable phytoremediation technology for the effective removal of toxic hexavalent chromium from mines wastewater. A water hyacinth species Eichhornia crassipes was chosen to remediate the problem of Cr (VI) pollution from wastewater. It has been observed that this plant was able to remove 99.5% Cr (VI) of the processed water of SCM in 15 days. This aquatic plant not only removed hexavalent Cr, but is also capable of reducing total dissolved solids (TDS), biological oxygen demand (BOD), chemical oxygen demand (COD), and other elements of water also. Large-scale experiment was also performed using 100 L of water from SCM and the same removal efficiency was achieved. PMID:27551860

PVC makers study expansions to meet demand growth

International Nuclear Information System (INIS)

Hunter, D.; Coeyman, M.

1993-01-01

As prospects for the polyvinyl chloride (PVC) industry continue to improve, the next batch of capacity increases is being studied. Vista Chemical (Houston) sees an opportunity to achieve what company president James R. Ball calls the lowest-cost capacity addition in the market, by debottlenecking its PVC plants at Aberdeen, MS and Oklahoma City. That would increase capacity 40%, adding 300 million lbs/year to Vista's 830 million lbs/year. US demand for PVC grew 12.5% through the first 10 months of 1992, to 7.3 billion lbs, according to the latest figures available from the Society of the Plastics Industry. Alan Bailey, Oxy-Chem's executive v.p./polymers and plastics, predicts a good demand year in 1993 - better even than 1992, driven by an upward trend in housing starts and a recovering economy

Enhanced removal of chemical oxygen demand, nitrogen and phosphorus using the ameliorative anoxic/anaerobic/oxic process and micro-electrolysis.

Science.gov (United States)

Bao, K Q; Gao, J Q; Wang, Z B; Zhang, R Q; Zhang, Z Y; Sugiura, N

2012-01-01

Synthetic wastewater was treated using a novel system integrating the reversed anoxic/anaerobic/oxic (RAAO) process, a micro-electrolysis (ME) bed and complex biological media. The system showed superior chemical oxygen demand (COD), total nitrogen (TN) and total phosphorus (TP) removal rates. Performance of the system was optimised by considering the influences of three major controlling factors, namely, hydraulic retention time (HRT), organic loading rate (OLR) and mixed liquor recirculation (MLR). TP removal efficiencies were 69, 87, 87 and 83% under the HRTs of 4, 8, 12 and 16 h. In contrast, HRT had negligible effects on the COD and TN removal efficiencies. COD, TN and TP removal efficiencies from synthetic wastewater were 95, 63 and 87%, respectively, at an OLR of 1.9 g/(L·d). The concentrations of COD, TN and TP in the effluent were less than 50, 15 and 1 mg/L, respectively, at the controlled MLR range of 75-100%. In this system, organics, TN and TP were primarily removed from anoxic tank regardless of the operational conditions.

A voltammetric electronic tongue as tool for water quality monitoring in wastewater treatment plants.

Science.gov (United States)

Campos, Inmaculada; Alcañiz, Miguel; Aguado, Daniel; Barat, Ramón; Ferrer, José; Gil, Luis; Marrakchi, Mouna; Martínez-Mañez, Ramón; Soto, Juan; Vivancos, José-Luis

2012-05-15

The use of a voltammetric electronic tongue as tool for the prediction of concentration levels of certain water quality parameters from influent and effluent wastewater from a Submerged Anaerobic Membrane Bioreactor pilot plant applied to domestic wastewater treatment is proposed here. The electronic tongue consists of a set of noble (Au, Pt, Rh, Ir, and Ag) and non-noble (Ni, Co and Cu) electrodes that were housed inside a stainless steel cylinder which was used as the body of the electronic tongue system. As a previous step an electrochemical study of the response of the ions sulphate, orthophosphate, acetate, bicarbonate and ammonium was carried out in water using the electrodes contained in the electronic tongue. The second part of the work was devoted to the application of the electronic tongue to the characterization of the influent and effluent waters from the wastewater treatment plant. Partial Least Squares analysis was used to obtain a correlation between the data from the tongue and the pollution parameters measured in the laboratory such as soluble chemical oxygen demand (CODs), soluble biological oxygen demand (BODs), ammonia (NH(4)-N), orthophosphate (PO(4)-P), Sulphate (SO(4)-S), acetic acid (HAC) and alkalinity (Alk). A total of 28 and 11 samples were used in the training and the validation steps, respectively, for both influent and effluent water samples. The electronic tongue showed relatively good predictive power for the determination of BOD, COD, NH(4)-N, PO(4)-P, SO(4)-S, and Alk. Copyright © 2012 Elsevier Ltd. All rights reserved.

Impact of Rangeland Degradation on Soil Physical, Chemical

African Journals Online (AJOL)

major threats to enhance a sustainable pastoral-livestock production in Ethiopia. ... overall negative impact on the soil physical and chemical characteristics, demanding ... chemical properties (Gemedo et al., 2006) as well as the rangeland .... parameters such as life forms (annuals and perennials), plant forms (woody plant,.

Aggregated Demand Modelling Including Distributed Generation, Storage and Demand Response

OpenAIRE

Marzooghi, Hesamoddin; Hill, David J.; Verbic, Gregor

2014-01-01

It is anticipated that penetration of renewable energy sources (RESs) in power systems will increase further in the next decades mainly due to environmental issues. In the long term of several decades, which we refer to in terms of the future grid (FG), balancing between supply and demand will become dependent on demand actions including demand response (DR) and energy storage. So far, FG feasibility studies have not considered these new demand-side developments for modelling future demand. I...

Water quality assessment of the Borska Reka river using the WPI (Water Pollution Index method

Directory of Open Access Journals (Sweden)

Milijašević Dragana

2011-01-01

Full Text Available The Borska Reka river (47 km long, 373 km2 of basin area is located in eastern Serbia and it is the biggest tributary of the river Veliki Timok. It is also one of the most polluted watercourses in Serbia. Using the data of the Republic Hydrometeorological Service of Serbia, the paper analyzes water pollution using the combined physical-chemical WPI index (water pollution index over two periods: 1993-1996 and 2006-2009. The analysis of parameters showed significantly increased values of heavy metals (especially iron and manganese which are indicators of inorganic pollution (primarily because of mining, but also increased values of organic pollution indicators (Biological Oxygen Demand-BOD5, ammonium, coliform germs, as the result of uncontrolled domestic wastewater discharge.

Optimal Waste Load Allocation Using Multi-Objective Optimization and Multi-Criteria Decision Analysis

Directory of Open Access Journals (Sweden)

L. Saberi

2016-10-01

Full Text Available Introduction: Increasing demand for water, depletion of resources of acceptable quality, and excessive water pollution due to agricultural and industrial developments has caused intensive social and environmental problems all over the world. Given the environmental importance of rivers, complexity and extent of pollution factors and physical, chemical and biological processes in these systems, optimal waste-load allocation in river systems has been given considerable attention in the literature in the past decades. The overall objective of planning and quality management of river systems is to develop and implement a coordinated set of strategies and policies to reduce or allocate of pollution entering the rivers so that the water quality matches by proposing environmental standards with an acceptable reliability. In such matters, often there are several different decision makers with different utilities which lead to conflicts. Methods/Materials: In this research, a conflict resolution framework for optimal waste load allocation in river systems is proposed, considering the total treatment cost and the Biological Oxygen Demand (BOD violation characteristics. There are two decision-makers inclusive waste load discharges coalition and environmentalists who have conflicting objectives. This framework consists of an embedded river water quality simulator, which simulates the transport process including reaction kinetics. The trade-off curve between objectives is obtained using the Multi-objective Particle Swarm Optimization Algorithm which these objectives are minimization of the total cost of treatment and penalties that must be paid by discharges and a violation of water quality standards considering BOD parameter which is controlled by environmentalists. Thus, the basic policy of river’s water quality management is formulated in such a way that the decision-makers are ensured their benefits will be provided as far as possible. By using MOPSO

The impact of job crafting on job demands, job resources, and well-being.

Science.gov (United States)

Tims, Maria; Bakker, Arnold B; Derks, Daantje

2013-04-01

This longitudinal study examined whether employees can impact their own well-being by crafting their job demands and resources. Based on the job demands-resources model, we hypothesized that employee job crafting would have an impact on work engagement, job satisfaction, and burnout through changes in job demands and job resources. Data was collected in a chemical plant at three time points with one month in between the measurement waves (N = 288). The results of structural equation modeling showed that employees who crafted their job resources in the first month of the study showed an increase in their structural and social resources over the course of the study (2 months). This increase in job resources was positively related to employee well-being (increased engagement and job satisfaction, and decreased burnout). Crafting job demands did not result in a change in job demands, but results revealed direct effects of crafting challenging demands on increases in well-being. We conclude that employee job crafting has a positive impact on well-being and that employees therefore should be offered opportunities to craft their own jobs.

Photocatalytic oxidation of a reactive azo dye and evaluation of the ...

African Journals Online (AJOL)

driniev

2004-07-03

Jul 3, 2004 ... biological oxygen demand (BOD) test. The results ... Toxicity testing of photo- catalytically ... The dye solution contained in a flask was placed on a magnetic ..... opacity of the suspension in the excess of TiO2 particles (Fig. 4).

Modelling Commodity Demands and Labour Supply with m-Demands

OpenAIRE

Browning, Martin

1999-01-01

In the empirical modelling of demands and labour supply we often lack data on a full set of goods. The usual response is to invoke separability assumptions. Here we present an alternative based on modelling demands as a function of prices and the quantity of a reference good rather than total expenditure. We term such demands m-demands. The advantage of this approach is that we make maximum use of the data to hand without invoking implausible separability assumptions. In the theory section qu...

Development of an eco- and material-efficient pellet production chain. A chemical study

Energy Technology Data Exchange (ETDEWEB)

Kuokkanen, M.

2013-06-01

According to the EU's strategy and the corresponding Finnish national strategy on waste materials, all kinds of waste must be utilised primarily as material (reuse, recycling) and secondarily as energy, and at the lowest level of waste hierarchy is their disposal using environmentally friendly methods. Today material efficiency is an essential topic in promoting sustainable use of natural resources, industrial by-products and waste material. The present goal proposed by the EU sets the target for the total proportion of renewable energy as high as 38% by 2020 in Finland. Up to 20 million tonnes of waste wood biomass per year are left unused in Finland, mainly in the forests during forestry operations, because supply and demand do not meet. As a consequence of high heat energy prices, the looming threat of climate change, the greenhouse effect and global as well as national demands to considerably increase the proportion of renewable energy, Finland currently has a tremendous interest in increasing decentralised pellet production alongside of large-scale factories. The aim of this thesis is to promote the development of eco-, material- and cost-efficient Nordic wood-based pellet production and utilisation of pellet bio-ash by means of chemical research. Using Finnish wood (sawdust and shavings) as a model raw material, the total functionality of a pilot-scale pellet facility combined with an extensive chemical toolbox was tested in this study to promote development of an eco-, material- and cost-efficient wood-based pellet production chain. The chemical toolbox includes measurements of moisture content, density, heat value, mechanical durability and particle size distribution, TG analysis and elementary analysis, as well as new applications for pellet biodegradation using BOD OxiTop equipment and optical microscopic staining methods. To improve the quality of pellets, considering the profitability of production and occupational safety factors (wood dust

Influences of mechanical pretreatment on the non-biological treatment of municipal wastewater by forward osmosis.

Science.gov (United States)

Hey, Tobias; Zarebska, Agata; Bajraktari, Niada; Vogel, Jörg; Hélix-Nielsen, Claus; la Cour Jansen, Jes; Jönsson, Karin

2017-09-01

Municipal wastewater treatment involves mechanical, biological and chemical treatment steps for protecting the environment from adverse effects. The biological treatment step consumes the most energy and can create greenhouse gases. This study investigates municipal wastewater treatment without the biological treatment step, including the effects of different pretreatment configurations, for example, direct membrane filtration before forward osmosis. Forward osmosis was tested using raw wastewater and wastewater subjected to different types of mechanical pretreatment, for example, microsieving and microfiltration permeation, as a potential technology for municipal wastewater treatment. Forward osmosis was performed using Aquaporin Inside™ and Hydration Technologies Inc. (HTI) membranes with NaCl as the draw solution. Both types of forward osmosis membranes were tested in parallel for the different types of pretreated feed and evaluated in terms of water flux and solute rejection, that is, biochemical oxygen demand (BOD 7 ) and total and soluble phosphorus contents. The Aquaporin and HTI membranes achieved a stable water flux with rejection rates of more than 96% for BOD 7 and total and soluble phosphorus, regardless of the type of mechanical pretreated wastewater considered. This result indicates that forward osmosis membranes can tolerate exposure to municipal waste water and that the permeate can fulfil the Swedish discharge limits.

Use of potassium permanganate integrated chemical-biological treatment schemes of wastewaters from agricultural industry; Aplicacion de permanganato potasico en sistemas de tratamiento integrado quimico-biologico en las aguas residuales de la industria agricola

Energy Technology Data Exchange (ETDEWEB)

Medialdea, J. M.; Arnaiz, M. C.; Isac, L.; Ruiz, C.; Valentin, R.; Martinez, M. F.; Garcia, S.; Lebrato, J. [Universidad de Sevilla (Spain); Cuenca, I.

2000-07-01

Present study assesses the applicability of a treatment scheme based on the combination of anaerobic biological digestion and chemical oxidation by potassium permanganate, in the purification of winery wastewaters. Biological digestion, performed using an experimental 1-liter reactor that operated discontinuously with completely mixed input and a mesophilic regime (35 degree centigree), removed 65% and 78% of water COD and BOD, and contributed 82,27% to the system global efficiency. Further chemical oxidation of effluent by Aquox -potassium permanganate eliminated 40% of residual COD, although contributed only 17,73% to global purification efficiency. However, effluent chemical oxidation at a dosage of 35 mg KMnO{sub 4}/L significantly increased effluent biodegradability. Results demonstrated the feasibility of analyzed working scheme and provide a positive valuation on the use of KMnO{sub 4} in the treatment of winery wastewaters. (Author) 24 refs.

Biotechnology for producing fuels and chemicals from biomass. Volume II. Fermentation chemicals from biomass

Energy Technology Data Exchange (ETDEWEB)

Villet, R. (ed.)

1981-02-01

The technological and economic feasibility of producing some selected chemicals by fermentation is discussed: acetone, butanol, acetic acid, citric acid, 2,3-butanediol, and propionic acid. The demand for acetone and butanol has grown considerably. They have not been produced fermentatively for three decades, but instead by the oxo and aldol processes. Improved cost of fermentative production will hinge on improving yields and using cellulosic feedstocks. The market for acetic acid is likely to grow 5% to 7%/yr. A potential process for production is the fermentation of hydrolyzed cellulosic material to ethanol followed by chemical conversion to acetic acid. For about 50 years fermentation has been the chief process for citric acid production. The feedstock cost is 15% to 20% of the overall cost of production. The anticipated 5%/yr growth in demand for citric acid could be enhanced by using it to displace phosphates in detergent manufacture. A number of useful chemicals can be derived from 2,3-butanediol, which has not been produced commercially on a large scale. R and D are needed to establish a viable commercial process. The commercial fermentative production of propionic acid has not yet been developed. Recovery and purification of the product require considerable improvement. Other chemicals such as lactic acid, isopropanol, maleic anhydride, fumarate, and glycerol merit evaluation for commercial fermentative production in the near future.

Feasibility of the UV/AA process as a pretreatment approach for bioremediation of dye-laden wastewater.

Science.gov (United States)

Yang, Minghui; Wu, Bingdang; Li, Qiuhao; Xiong, Xiaofeng; Zhang, Haoran; Tian, Yu; Xie, Jiawen; Huang, Ping; Tan, Suo; Wang, Guodong; Zhang, Li; Zhang, Shujuan

2018-03-01

Biodegradability and toxicity are two important indexes in considering the feasibility of a chemical process for environmental remediation. The acetylacetone (AA) mediated photochemical process has been proven as an efficient approach for dye decolorization. Both AA and its photochemical degradation products had a high bioavailability. However, the biocompatibility and ecotoxicology of the UV/AA treated solutions are unclear yet. In the present work, we evaluated the biocompatibility and toxicity of the UV/AA treated solutions at both biochemical and organismal levels. The biodegradability of the treated solution was evaluated with the ratio of 5-d biological oxygen demand (BOD 5 ) to chemical oxygen demand (COD) and a 28-d activated sludge assay (Zahn-Wellens tests). The UV/AA process significantly improved the biodegradability of the tested dye solutions. Toxicity was assessed with responses of microorganisms (microbes in activated sludge and Daphnia magna) and plants (bok choy, rice seed, and Arabidopsis thaliana) to the treated solutions, which showed that the toxicity of the UV/AA treated solutions was lower or comparable to that of the UV/H 2 O 2 counterparts. The results are helpful for us to determine whether the UV/AA process is applicable to certain wastewaters and how the UV/AA process could be effectively combined into a sequential chemical-biological water treatment. Copyright © 2017 Elsevier Ltd. All rights reserved.

Physical and chemical monitoring of environment components at Rirang and Eko Remaja West Kalimantan

International Nuclear Information System (INIS)

Sorot S, Achmad; Deddi, Eep; Wismawati, Titi; Widarti, Sri

2002-01-01

The aim of the environmental monitoring is to know the possibility change environmental component quality at Kalan area West Kalimantan. This monitoring activity has done parallel to the exploration and mining research on radioactive ore at Kalan area. The monitoring consist the activities such as river water sampling, stream sediments, soil, and pH. Water and sediment samples were taken from the same location as what been carried out at the previously research sampling. COD and BOD parameters of the water were been analyzed in field, while the other parameters were analyzed at Jakarta using spectrophotometer and Eberline alpha counter SACR5. Data obtained on BOD, COD, and heavy metal constant such as Ca, As, Mg, Fe, Ni, Zn, Cu, Pb, Mn, Mc, U, Th nad Ra lesser than that in 1997/1998 monitoring. Base on the criteria of EQAM, AMDAL the Rirang water quality (4.62 scales) and Eko Remaja water quality (4.76) are fairly good. Result of stream sediment and soil samples analysis are relatively close to 1997/1998 monitoring, except U and Th content were increase 1-5 %. Result of soil analysis on the parameters Ca, Ni, Zn, Cu, Pb, Mn, Mo, U, Th, and fe relatively same with the 1997/1998 monitoring, except the uranium content is lesser than that monitoring. The maximal radioactivity values were accepted is 0.4 Bq/l. Based on the physical and chemical assay of the river water, stream sediments, and soils samples shown that the quality of the environment was not deteriorating, that mean the exploration and mining research on radioactive ores are do not disturb the environment

EFFECT OF OZONATED WATER ON THE ASSIMILABLE ORGANIC CARBON AND COLIFORM GROWTH RESPONSE VALUES AND ON PATHOGENIC BACTERIA SURVIVAL

Science.gov (United States)

The assimilable organic carbon (AOC) and coliform growth response (CGR) are bioassays used to determine water quality. AOC and CGR are better indexes in determining whether water can support the growth of bacteria than biological oxygen demand (BOD). The AOC value of reconditione...

Treatment of textile effluent by chemical (Fenton's Reagent) and biological (sequencing batch reactor) oxidation

International Nuclear Information System (INIS)

Rodrigues, Carmen S.D.; Madeira, Luis M.; Boaventura, Rui A.R.

2009-01-01

The removal of organic compounds and colour from a synthetic effluent simulating a cotton dyeing wastewater was evaluated by using a combined process of Fenton's Reagent oxidation and biological degradation in a sequencing batch reactor (SBR). The experimental design methodology was first applied to the chemical oxidation process in order to determine the values of temperature, ferrous ion concentration and hydrogen peroxide concentration that maximize dissolved organic carbon (DOC) and colour removals and increase the effluent's biodegradability. Additional studies on the biological oxidation (SBR) of the raw and previously submitted to Fenton's oxidation effluent had been performed during 15 cycles (i.e., up to steady-state conditions), each one with the duration of 11.5 h; Fenton's oxidation was performed either in conditions that maximize the colour removal or the increase in the biodegradability. The obtained results allowed concluding that the combination of the two treatment processes provides much better removals of DOC, BOD 5 and colour than the biological or chemical treatment alone. Moreover, the removal of organic matter in the integrated process is particularly effective when Fenton's pre-oxidation is carried out under conditions that promote the maximum increase in wastewater biodegradability.

Oxidative treatment characteristics of biotreated textile-dyeing wastewater and chemical agents used in a textile-dyeing process by advanced oxidation process.

Science.gov (United States)

Lim, B R; Hu, H Y; Ahn, K H; Fujie, K

2004-01-01

The oxidative treatment characteristics of biotreated textile-dyeing wastewater and typical chemicals such as desizing, scouring, dispersing and swelling agents used in the textile-dyeing process by advanced oxidation process were experimentally studied. The refractory organic matters remained in the effluent of biological treatment process without degradation may be suitable for the improvement of biodegradability and mineralized to CO2 by combined ozonation with and without hydrogen peroxide. On the other hand, the refractory chemicals contained in the scouring agent A and swelling agent may not be mineralized and their biodegradability may not be improved by ozonation. However, the BOD/DOC ratio of scouring agent B increased from 0.3 to 0.45 after ozonation. Based on the results described above, advanced treatment process involving the ozonation without and with the addition of hydrogen peroxide, followed by biological treatment was proposed for the treatment of refractory wastewater discharged from the textile-dyeing process.

Incorporation of oxygen contribution by plant roots into classical dissolved oxygen deficit model for a subsurface flow treatment wetland.

Science.gov (United States)

Bezbaruah, Achintya N; Zhang, Tian C

2009-01-01

It has been long established that plants play major roles in a treatment wetland. However, the role of plants has not been incorporated into wetland models. This study tries to incorporate wetland plants into a biochemical oxygen demand (BOD) model so that the relative contributions of the aerobic and anaerobic processes to meeting BOD can be quantitatively determined. The classical dissolved oxygen (DO) deficit model has been modified to simulate the DO curve for a field subsurface flow constructed wetland (SFCW) treating municipal wastewater. Sensitivities of model parameters have been analyzed. Based on the model it is predicted that in the SFCW under study about 64% BOD are degraded through aerobic routes and 36% is degraded anaerobically. While not exhaustive, this preliminary work should serve as a pointer for further research in wetland model development and to determine the values of some of the parameters used in the modified DO deficit and associated BOD model. It should be noted that nitrogen cycle and effects of temperature have not been addressed in these models for simplicity of model formulation. This paper should be read with this caveat in mind.

Survey of microbiological and chemical quality of the swimming beaches along the Persian Gulf in Bushehr port

Directory of Open Access Journals (Sweden)

2015-05-01

Full Text Available Background: Swimming is highly recommended because of its potentially beneficial effects on the joints and people’s general sense of well-being. But unfortunately the discharing of urban and industrial wastewaters into sea with their high level of pathogens, heavy metals and other pollutants, increase concerns about its consequences on swimmers’ health and ecology. The aim of this study was to investigate the microbial and chemical quality of Persian Gulf Sea beaches in Bushehr port and compare it to the existing standards. Materials and Methods: In this study, 30 samples were taken from the beaches at TV-Park, Daneshjo-Park and Eskele-Jofreh, in August 2012. The mean values of total coliforms, fecal coliforms, pseudomonas, HPC, heavy metals and BOD were determined by standard methods. Results: The mean values of total coliforms, fecal coliforms, and pseudomonas along Bushehr port beaches were 540, 165.56 and 6 MPN/100ml respectively.The mean value of HPC was 1580.66 CFU/ml. Also the mean concentrations of Fe, Zn, Pb, Cd, Cr, Cu and BOD were 0.1676, 0.013, 0.025, 0.0016, 0.039, 0 and 21.3 mg/l respectively. Conclusion: The results showed that the mean values of indicator microorganisms in all stations were higher than the existing standards and the mean concentration of heavy metals were lower than the existing standard, which indicates higher pollution more due to urban wastewater compare to industrial wastewater. Therefore Bushehr port beaches are contaminated considering indicator bacteria measurments that can be dangerous for swimmers health.

Estimation of optimal capacity of the module through the demand analysis of refinery hydrogen

Energy Technology Data Exchange (ETDEWEB)

Yoon, Young-Seek; Kim, Ho-Jin; Kim, Il-Su [SK energy Institution of Technology, Daejeon (Korea, Republic of)] (and others)

2006-02-15

Hydrogen is focused as energy carrier, not an energy source on the rising of problems such as exhaustion of fossil fuel and environment pollution. Thermochemical hydrogen production by nuclear energy has potential to efficiently produce large quantities of hydrogen without producing greenhouse gases. The oil refiners and petro-chemical plant are very large, centralized producers and users of industrial hydrogen, and they a high-potential early market for hydrogen produced by nuclear energy. Therefore, hydrogen market of petro-chemical industry as demand site for nuclear hydrogen was investigated and worked for demand forecast of hydrogen in 2020. Also we suggested possible supply plans of nuclear hydrogen considered regional characteristics. The hydrogen production cost was analyzed and estimated for nuclear hydrogen as well as conventional hydrogen production such as natural gas reforming and coal gasification in various range.

Estimation of optimal capacity of the module through the demand analysis of refinery hydrogen

International Nuclear Information System (INIS)

Yoon, Young-Seek; Kim, Ho-Jin; Kim, Il-Su

2006-02-01

Hydrogen is focused as energy carrier, not an energy source on the rising of problems such as exhaustion of fossil fuel and environment pollution. Thermochemical hydrogen production by nuclear energy has potential to efficiently produce large quantities of hydrogen without producing greenhouse gases. The oil refiners and petro-chemical plant are very large, centralized producers and users of industrial hydrogen, and they a high-potential early market for hydrogen produced by nuclear energy. Therefore, hydrogen market of petro-chemical industry as demand site for nuclear hydrogen was investigated and worked for demand forecast of hydrogen in 2020. Also we suggested possible supply plans of nuclear hydrogen considered regional characteristics. The hydrogen production cost was analyzed and estimated for nuclear hydrogen as well as conventional hydrogen production such as natural gas reforming and coal gasification in various range

Innovation and Demand

DEFF Research Database (Denmark)

Andersen, Esben Sloth

2007-01-01

the demand-side of markets in the simplest possible way. This strategy has allowed a gradual increase in the sophistication of supply-side aspects of economic evolution, but the one-sided focus on supply is facing diminishing returns. Therefore, demand-side aspects of economic evolution have in recent years...... received increased attention. The present paper argues that the new emphasis on demand-side factors is quite crucial for a deepened understanding of economic evolution. The major reasons are the following: First, demand represents the core force of selection that gives direction to the evolutionary process....... Second, firms' innovative activities relate, directly or indirectly, to the structure of expected and actual demand. Third, the demand side represents the most obvious way of turning to the much-needed analysis of macro-evolutionary change of the economic system....

An evaluation of solutions to moment method of biochemical oxygen ...

African Journals Online (AJOL)

This paper evaluated selected solutions of moment method in respect to Biochemical Oxygen Demand (BOD) kinetics with the aim of ascertain error free solution. Domestic - institutional wastewaters were collected two - weekly for three months from waste - stabilization ponds in Obafemi Awolowo University, Ile - Ife.

Instruments for integrated water resources management : water quality modeling for sustainable wastewater management

NARCIS (Netherlands)

Barjoveanu, George; Teodosiu, Carmen; Cojocariu, Claudia; Augustijn, Dionysius C.M.; Craciun, Ioan

2013-01-01

This study presents the development and use of a hydraulic-coupled water quality model for the simulation of Biochemical Oxygen Demand (BOD) concentrations in the Bahlui River, a small river located in northeastern Romania. This river experiences the typical pollution problems for many Romanian

Loading Concentrations of Pollutant in Alur Ilmu at UKM Bangi Campus: Event Mean Concentration (EMC) Approach

International Nuclear Information System (INIS)

Haslinur Md Din; Mohd Ekhwan Toriman; Mazlin Mokhtar

2012-01-01

Water pollutant loadings and river discharge are among the basic data used in determining the dynamicity of a river. The input of water quality and river discharge are usually available through the collection of water samples in the field or at the observatory, and are done automatically using the data logger sensor. This paper discusses the concentrations pollutant load water quality and its relationship with discharge (m 3 / s) using Event Mean Concentration (EMC) in the Alur Ilmu, UKM source from the Diptrokarp forest at Hutan Simpan Bangi (2 degree 55' 1 4.72 N 101 degree 46' 5 7.37 E). Alur Ilmu is a 1.79 km long stretching across the main campus of National University of Malaysia before flowing into the Langat River. Water quality was measured using automatic gauging and continuous water quality stations which are installed at downstream of Alur Ilmu (2 degree 55 ' 40.33 N 100 degree 46 ' 47.15 E) and involves in measuring the parameters of total dissolved solid (TDS) and dissolved oxygen (DO). Laboratory analysis carried out for chemical parameters such as ammonia nitrogen (NH 3 -N), total suspended solid (TSS), biochemical oxygen demand (BOD) and chemical oxygen demand (COD) in accordance with guidelines American Public Health Association (APHA, 1995). The normal discharge rate recorded at Alur Ilmu is 0.33 m 3 / s and the wet discharge is 13.04 m 3 / s.The total estimated pollutant loadings according to EMC as DO (18.51±3.01 mg/ L), TDS (794.92±186.72 mg/ L), BOD (11.57±0.28 mg/ L), COD (201.29±1.55 mg/ l), TSS (470.03±27.63 mg/ L) and Ammonia Nitrogen (2.52±0.0 mg/ L). Correlation test showed a direct relationship between rainfall and flow (Q) and several pollutant loadings with R 2 =1 at a significance level of 0.05. The study also classified some of the pollutants concentrations in class III and IV as determined by the Water Quality Index (WQI). (author)

Meeting residential space heating demand with wind-generated electricity

International Nuclear Information System (INIS)

Hughes, Larry

2010-01-01

Worldwide, many electricity suppliers are faced with the challenge of trying to integrate intermittent renewables, notably wind, into their energy mix to meet the needs of those services that require a continuous supply of electricity. Solutions to intermittency include the use of rapid-response backup generation and chemical or mechanical storage of electricity. Meanwhile, in many jurisdictions with lengthy heating seasons, finding secure and preferably environmentally benign supplies of energy for space heating is also becoming a significant challenge because of volatile energy markets. Most, if not all, electricity suppliers treat these twin challenges as separate issues: supply (integrating intermittent renewables) and demand (electric space heating). However, if space heating demand can be met from an intermittent supply of electricity, then both of these issues can be addressed simultaneously. One such approach is to use off-the-shelf electric thermal storage systems. This paper examines the potential of this approach by applying the output from a 5.15 MW wind farm to the residential heating demands of detached households in the Canadian province of Prince Edward Island. The paper shows that for the heating season considered, up to 500 households could have over 95 percent of their space heating demand met from the wind farm in question. The benefits as well as the limitations of the approach are discussed in detail. (author)

Study on the Development of Household Wastewater Treatment Unit

Directory of Open Access Journals (Sweden)

Ali Hadi Ghawi

2018-03-01

Full Text Available The cities of Iraq in general and the city of Al Diwaniyah in particular are characterized by the fact that the majority of households use septic tank to dispose of sewage, leading to contamination of ground and surface water and a disturbance to the environment. The objective of this study is to protect the water and soil sources from the risk of pollution, eliminate the process of perfusion and thus, reduce costs, maintain public health, as well as design and implement the proposed purification unit for domestic wastewater treatment. A domestic wastewater treatment unit has been improved to meet the standard specifications for the quality of the effluent wastewater. In this study, a compact non-electric sewage treatment unit was improved and implemented. Treatment is based on an effective modern biological purification process. Experimental verification and analysis of results were performed to demonstrate the improvement of physical and chemical parameters. The performance of the septic tanks-bioreactor gave satisfactory results. The removal efficiencies of Total Biochemical Oxygen Demand (BOD, Total Chemical Oxygen Demand (COD, NH4-N, Total Nitrogen and Total Suspended Solid (TSS were 96.9%, 84.6%, 78.8%, 79.9% and 95.3%, respectively.

Avaliação de desempenho de lagoa de polimento para pós-tratamento de reator anaeróbio de manta de lodo (UASB no tratamento de águas residuárias de suinocultura Evaluation of the performance of a polishing pond for the post-treatment of the effluent from an upflow anaerobic sludge blanket (UASB reactor treating swine wastewater

Directory of Open Access Journals (Sweden)

L.S. Rodrigues

2009-12-01

Full Text Available Avaliou-se o desempenho de uma lagoa de polimento, no tratamento de efluentes de águas residuárias de suinocultura de um reator anaeróbio de manta de lodo (UASB. O sistema foi composto de decantador, reator UASB, em escala real, e lagoa de polimento em escala experimental. As análises físico-químicas realizadas foram: temperatura, pH, demanda bioquímica de oxigênio (DBO, demanda química de oxigênio (DQO, sólidos suspensos totais (SST e sólidos suspensos voláteis (SSV, nitrogênio total kjedhal (NTK, nitrogênio amoniacal (N-am. e orgânico (N-org., fósforo total (Pt, coliformes totais e termotolerantes. A lagoa de polimento apresentou alto desempenho, com remoção média de 58,9% de DBO, 60,1% de NTK, 57% de N-am. e 95,34% de coliformes termotolerantes.The performance of a polishing pond for treating swine wastewater from an upflow anaerobic sludge blanket (UASB reactor was evaluated. The system was assembled with a slat settler, followed by an UASB reactor, on a real scale, and a post-treatment pond, on a demonstration scale. The following parameters were analyzed: temperature, pH, biochemical oxygen demand (BOD, chemical oxygen demand (COD, total suspended solids (TSS, volatile suspended solids (VSS, total Kjedahl nitrogen (NTK, ammonia nitrogen (N-am., organic nitrogen, total phosphorus, and total and thermotolerant coliforms. The polishing pond was highly efficient, removing an average of 58.9% of BOD, 60.1% of NTK, 57% of N-am., and 95.34% of thermotolerant coliforms.

Quality of wastewater used for conventional irrigation in the vicinity of lahore and its impact on receiving soils and vegetables

International Nuclear Information System (INIS)

Bashir, F.; Tariq, M.; Khan, R.A.; Shafiq, T.

2014-01-01

The quality of wastewater was evaluated from Rohi Nullah, Lahore, Pakistan, for one year (2008-2009) from those points where it is used for irrigation of crops on both sides of Nullah. The quality of wastewater was evaluated for pollution load including pH, sulphide, phenol, methylene blue active substances, chemical oxygen demand (COD), biochemical oxygen demand (BOD), irrigation quality (electric conductivity, total dissolved solids, total suspended solids, sodium adsorption ratio, residual sodium carbonate and chlorides) nutritional value (total nitrogen, total phosphorus and total potassium) and for metal concentration. The metals analysed were cadmium, nickel, chromium, zinc, manganese, cobalt and copper. With respect to pollution load BOD, COD and sulphide concentration was above the National Environmental Quality Standard (NEQS) limit. Nitrogen and phosphorus were contained at levels of concern in wastewater but the level of potassium was below crop requirements. The concentration of nickel, chromium, manganese and copper was above the FAO standards, while the concentration of cadmium, zinc and cobalt fell within FAO standards. Considering NEQS standards, the metals concentration was within limits. Temporal variations were prominent in some parameters and mostly higher values were observed in summer and lower in winter season. There was accumulation of heavy metals in soils receiving wastewater for irrigation. The metal contents in soils follow the order Mn> Co> Zn> Cr > Ni > Cu > Cd. It was observed that the concentration of all studied toxic metals in edible part of the vegetables was above the critical level. Finally, it was concluded that the practice of using wastewater in irrigation for growing vegetables and other crops is non-sustainable. (author)

Feasibility of vermicomposting dewatered sludge from paper mills using Perionyx excavatus

Directory of Open Access Journals (Sweden)

Puspanjali Sonowal

2013-06-01

Full Text Available India has a large network of pulp and paper mills of varying capacity. On an industrial scale the sludge from paper and pulp mills is disposed of either as landfill or incinerated. Both methods result in the loss of a valuable resource and have obvious environmental and economic disadvantages. The solid waste from pulp and paper mills is a source of organic matter and its proper disposal and management is the responsibility of the industry. As composting/vermicomposting could be used to transform this waste trials were carried out to determine the feasibility of converting dewatered sludge (DS into a value added end product using an earthworm, Perionyx excavatus. The vermicomposting of the waste resulted in an increase in its electrical conductivity (EC, ash content, total nitrogen (TN, total phosphorous (TP and available phosphorous (AP, respectively, and a decrease in total organic carbon (TOC, biochemical oxygen demand (BOD, chemical oxygen demand (COD, oxygen uptake rate (OUR and evolution of carbon dioxide (CO2. Overall, the best treatment was T5 in which there was a 76.1% increase in TP, 58.7% in TN, 74.5% decrease in TOC , and a reduction of 6.7 fold in the production of CO2 and 10.7 fold in BOD, respectively. Our trials demonstrate that vermicomposting using an epigeic earthworm, Perionyx excavatus, is an alternate and environmentally safe way of recycling paper mill sludge if it is mixed with an appropriate amount of cow dung and food processing waste. Overall T5 was the best combination of paper mill sludge and waste for vermicomposting followed by T3, T2, T4 and T1, respectively.

Treatment and Energy Valorisation of an Agro-Industrial Effluent in Upflow Anaerobic Sludge Reactor (UASB)

Science.gov (United States)

Martins, Ramiro; Boaventura, Rui; Paulista, Larissa

2017-12-01

The accelerated growth of the population brings with it an increase in the generation of agro-industrial effluents. The inadequate discharge of these effluents significantly affects the quality of water resources. In this way, it becomes important to invest in treatment processes for agro-industrial effluents, particularly low-cost ones. In this context, the present study includes the design and construction of an UASB reactor and optimization of the anaerobic digestion treatment of the raw effluent from sweet chestnut production in the agro-industrial company Sortegel. The efficiency of the system was evaluated through the determination / monitoring of oxygen chemical oxygen demand (COD), biochemical oxygen demand (BOD5), total suspended solids (TSS), biogas production rate and quality (% methane). The reactor was fed for 25 weeks and operated under mesophilic conditions (temperature 30-40 °C). Different values were tested for the hydraulic retention time (HRT) and volumetric flow rate (VF): 0.66 days (VF=1509 L.m-3.d-1); 1.33 days (VF=755 L.m-3.d-1); 2.41 d days (VF=415 L.m-3.d-1). The average COD removal efficiency reached values of 69%, 82% and 75%, respectively, and simultaneously the associated BOD5 removal efficiency was 84%, 91% and 70%. As regards TSS, removal values were 78%, 94% and 63%. In addition, high methane production rates were obtained, between 2500 and 4800 L CH4.kg-1 COD removed d-1. For all the hydraulic retention times tested, high concentrations of methane in the biogas were recorded: 66-75%, 70% and 75% for HRT of 0.66, 1.33 and 2.41 days, respectively.

Biochemistry Oxidation Process for Treatment the Simulation of Organic Liquid Radioactive Waste

International Nuclear Information System (INIS)

Gunandjar; Zainus Salimin; Sugeng Purnomo; Ratiko

2010-01-01

The nuclear industry activities generate the organic liquid wastes such as detergent waste from laundry, solvent waste of 30% TBP (tri-n-butyl phosphate) in kerosene from purification or recovery of uranium from rejection of nuclear fuel element fabrication, and solvent waste containing D 2 EHPA (di-2-ethyl hexyl phosphoric acid) and TOPO (trioctyl phospine oxide) in kerosene from phosphoric acid purification. The wastes are included in category of the hazard and poison materials which also radioactive, so that the wastes have to be treated to detoxification of the hazard and poison materials and decontamination of the radionuclides. The research of biochemistry oxidation process for treatment the simulation of organic liquid radioactive waste from laundry using mixture of aerobe bacteria of bacillus sp, pseudomonas sp, arthrobacter sp, and aeromonas sp have been carried out. The waste containing detergent 1,496 g/Litre, activity 10 -1 Ci/m 3 , with COD (Chemical Oxygen Demand) 128, BOD (Biological Oxygen Demand) 68 and TSS (Total Suspended Solid) 1000 ppm, it is treated by biochemistry oxidation with addition of bacteria which be fed nutrition of nitrogen and phosphor, and aeration. The result show that the bacteria can decompose the detergent to become carbon dioxyde and water so that can fulfill the quality standard of water group-B with content of BOD and COD are 6 and 10 ppm respectively, the time of decomposition is needed 106 hours to be fulfill the quality standard of water. The longer of process time will give bigger the total solid content in sludge, because the biomass generated from the colony of bacteria which life and dead to so much. (author)

The effect of industrial effluent stream on the groundwater

International Nuclear Information System (INIS)

Yasar, A.; Ahmad, N.; Chaudhry, M.N.; Sarwar, M.

2005-01-01

This study was performed to investigate the effect of the industrial wastewater stream on the groundwater. Wastewater was characterized in terms of inorganic and organic constituents. Inorganic constituents included Na/sup +/, Ca/sup 2+/ K/sup +/, Cl/sup -/, NO/sub 3//sup -/ and SO/sub 4//sup 2-/ coupled with heavy metal elements such as, Cd, Cr, Pb, Mn, Cu, Ni, Fe and In. Organic load of the stream was determined in terms of chemical oxygen demand (COD), biological oxygen demand (BOD/sub 5/) and ammonia-nitrogen (NH/sub 3/-N) contents. Other characteristics were pH, electrical conductivity (EC) and total dissolved solids (TDS). The correlation coefficients between quality parameter pairs of stream water and groundwater were determined to ascertain the source of groundwater contamination. At station 1, BOD/sub 5/ and COD contents were 20 times and Cr concentration was 10 times higher than the permissible limits for stream water [1]. Contents of these parameters reflected the level of industrial and domestic pollution coming from India. However, large variations in the levels of these parameters at down stream sites of the drain were characteristic of type and nature of industrial effluents and domestic sewage joining the stream. Analysis results of more than one hundred groundwater samples from shallow and deep wells around the drain showed that groundwater of shallow aquifers was contaminated due to drain water. A comparison of the contents of these parameters in shallow wells with WHO standards showed that some parameters such as turbidity, TDS, Na/sup +/, F -and heavy metals like Cr were found higher than the permissible limits. (author)

Characterization of domestic graywater and graywater solids.

Science.gov (United States)

Sievers, Jan Christian; Londong, Jörg

2018-03-01

The knowledge of loads and concentrations is fundamental for the design of graywater treatment units, but the data on the characteristics of graywater and in particular graywater solids are weak. As general design values regarding graywater treatment facilities are not available for Germany, the objective of this article is to elaborate the characteristics of graywater and graywater solids. This paper describes the results of six sampling campaigns carried out on graywater systems in the German cities Berlin, Lübeck and Kiel. All graywater samples were collected proportional to the flow and the graywater solids were gathered separately. The collected data include graywater volumes and characteristics regarding the organic pollution (chemical oxygen demand (COD), 5-day biochemical oxygen demand (BOD 5 )) and nutrients (total nitrogen (TN), total phosphorus (TP)). The graywater volume fluctuated depending on the location. The specific average flow was 68 litre per inhabitant per day (L/inh.d). Inhabitant-specific loads of 49.3 gCOD t /inh·d, 28 gBOD 5 /inh.d, 1 gTN t /inh.d and 0.38 gTP t /inh.d (subscript 't' = total) were found. Information about the composition of graywater solids in terms of quantity and quality is seriously lacking. Therefore, graywater solids were examined with respect to organic matter (COD) and nutrients (TN, TP). The contribution of graywater solids with particle sizes over 200 microns in relation to the total inhabitant-specific load was approximately 3-8% depending on the parameter. The qualitative and quantitative characteristics of the investigated graywater fractions may serve as a base for the estimation of design values.

Effect of circulation on wastewater treatment by Lemna gibba and Lemna minor (floating aquatic macrophytes).

Science.gov (United States)

Demirezen Yilmaz, Dilek; Akbulut, Hatice

2011-01-01

In this study, laboratory tests were performed in order to examine growth characteristics of floating aquatic macrophytes (Lemna gibba and Lemna minor) in the presence of wastewater with circulation. The results showed that circulation of the waste water enhanced the kinetics of the process, as compared to the control systems. However, prolonged application of high circulation level had a different effect. In the presence of circulation with aquatic plants, there was additional 85.3-88.2% for BODs and 59.6-66.8% for COD decreases in the water quality indicators. In this study, the effectiveness of L. gibba and L. minor with circulation addition for the removal of four heavy metals (Pb, Ni, Mn, and Cu) from waste water was also investigated. Results from analysis confirmed the accumulation of different metals within the plant and a corresponding decrease of metals in the waste water. At the end of the study of circulation, L. gibba provided the metal removal for Cu, Pb, Ni, and Mn in the waste water as the ratio of 57%, 60%, 60%, and 62%, respectively. In this context, the best results were obtained when the action of L. gibba and L. minor plants, was combined with that of circulation. It is shown that in the presence of L. gibba and L. minor plants that are supplemented with circulation, the national standards of biochemical oxygen demand (BOD5) 27-33 mgL(-1) and chemical oxygen demand (COD) 62-78 mgL(-1) for L. minor and L. gibba, respectively, were reached after treatment. The new results can be used for design calculations regarding expected removal of pollutants by aquatic floating plants.

Expanding Rational Molecular Design beyond Pharma: Metrics to Guide Safer Chemical Design

Science.gov (United States)

The demand for safer, healthier and sustainable products, materials and processes has been increasing over the past several years. Differentiating which chemicals are relatively less hazardous than others, often referred to as “greener” or “sustainable, demands a comprehensive, h...

Model development for prediction and mitigation of dissolved oxygen sags in the Athabasca River, Canada

Energy Technology Data Exchange (ETDEWEB)

Martin, Nancy, E-mail: nancy@ualberta.ca [Department of Civil and Environmental Engineering, University of Alberta, Edmonton, AB, Canada T6G 2W2 (Canada); McEachern, Preston [Tervita Corporation, AB (Canada); Yu, Tong; Zhu, David Z. [Department of Civil and Environmental Engineering, University of Alberta, Edmonton, AB, Canada T6G 2W2 (Canada)

2013-01-15

Northern rivers exposed to high biochemical oxygen demand (BOD) loads are prone to dissolved oxygen (DO) sags in winter due to re-aeration occurring within limited open water leads. Additionally, photosynthesis is reduced by decreased daylight hours, inability of solar radiation to pass through ice, and slower algal growth in winter. The low volumetric flow decreases point-source dilution while their travel time increases. The Athabasca River in Alberta, Canada, has experienced these sags which may affect the aquatic ecosystem. A water quality model for an 800 km reach of this river was customized, calibrated, and validated specifically for DO and the factors that determine its concentration. After validation, the model was used to assess the assimilative capacity of the river and mitigation measures that could be deployed. The model reproduced the surface elevation and water temperature for the seven years simulated with mean absolute errors of < 15 cm and < 0.9 °C respectively. The ice cover was adequately predicted for all seven winters, and the simulation of nutrients and phytoplankton primary productivity were satisfactory. The DO concentration was very sensitive to the sediment oxygen demand (SOD), which represented about 50% of the DO sink in winter. The DO calibration was improved by implementing an annual SOD based on the BOD load. The model was used to estimate the capacity of the river to assimilate BOD loads in order to maintain a DO concentration of 7 mg/L, which represents the chronic provincial guideline plus a buffer of 0.5 mg/L. The results revealed the maximum assimilative BOD load of 8.9 ton/day at average flow conditions, which is lower than the maximum permitted load. In addition, the model predicted a minimum assimilative flow of about 52 m{sup 3}/s at average BOD load. Climate change scenarios could increase the frequency of this low flow. A three-level warning-system is proposed to manage the BOD load proactively at different river

Operational High Resolution Chemical Kinetics Simulation, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — Numerical simulations of chemical kinetics are critical to addressing urgent issues in both the developed and developing world. Ongoing demand for higher resolution...

Asian oil demand

International Nuclear Information System (INIS)

Fesharaki, F.

2005-01-01

This conference presentation examined global oil market development and the role of Asian demand. It discussed plateau change versus cyclical movement in the global oil market; supply and demand issues of OPEC and non-OPEC oil; if high oil prices reduce demand; and the Asian oil picture in the global context. Asian oil demand has accounted for about 50 per cent of the global incremental oil market growth. The presentation provided data charts in graphical format on global and Asia-Pacific incremental oil demand from 1990-2005; Asia oil demand growth for selected nations; real GDP growth in selected Asian countries; and, Asia-Pacific oil production and net import requirements. It also included charts in petroleum product demand for Asia-Pacific, China, India, Japan, and South Korea. Other data charts included key indicators for China's petroleum sector; China crude production and net oil import requirements; China's imports and the share of the Middle East; China's oil exports and imports; China's crude imports by source for 2004; China's imports of main oil products for 2004; India's refining capacity; India's product balance for net-imports and net-exports; and India's trade pattern of oil products. tabs., figs

Dynamic energy-demand models. A comparison

International Nuclear Information System (INIS)

Yi, Feng

2000-01-01

This paper compares two second-generation dynamic energy demand models, a translog (TL) and a general Leontief (GL), in the study of price elasticities and factor substitutions of nine Swedish manufacturing industries: food, textiles, wood, paper, printing, chemicals, non-metallic minerals, base metals and machinery. Several model specifications are tested with likelihood ratio test. There is a disagreement on short-run adjustments; the TL model accepts putty-putty production technology of immediate adjustments, implying equal short- and long-run price elasticities of factors, while the GL model rejects immediate adjustments, giving out short-run elasticities quite different from the long-run. The two models also disagree in substitutability in many cases. 21 refs

Impacts of a high-discharge submarine sewage outfall on water quality in the coastal zone of Salvador (Bahia, Brazil)

KAUST Repository

Roth, Florian; Lessa, G.C.; Wild, C.; Kikuchi, R.K.P.; Naumann, M.S.

2016-01-01

Carbon and nitrogen stable isotopic signatures of suspended particulate organic matter and seawater biological oxygen demand (BOD) were measured along a coastal transect during summer 2015 to investigate pollution impacts of a high-discharge submarine sewage outfall close to Salvador, Brazil. Impacts of untreated sewage discharge were evident at the outfall site by depleted δ13Corg and δ15N signatures and 4-fold increased BOD rates. Pollution effects of a sewage plume were detectable for more than 6 km downstream from the outfall site, as seasonal wind- and tide-driven shelf hydrodynamics facilitated its advective transport into near-shore waters. There, sewage pollution was detectable at recreational beaches by depleted stable isotope signatures and elevated BOD rates at high tides, suggesting high bacterial activity and increased infection risk by human pathogens. These findings indicate the urgent necessity for appropriate wastewater treatment in Salvador to achieve acceptable standards for released effluents and coastal zone water quality.

Organic pollution of rivers: Combined threats of urbanization, livestock farming and global climate change.

Science.gov (United States)

Wen, Yingrong; Schoups, Gerrit; van de Giesen, Nick

2017-02-23

Organic pollution of rivers by wastewater discharge from human activities negatively impacts people and ecosystems. Without treatment, pollution control relies on a combination of natural degradation and dilution by natural runoff to reduce downstream effects. We quantify here for the first time the global sanitation crisis through its impact on organic river pollution from the threats of (1) increasing wastewater discharge due to urbanization and intensification of livestock farming, and (2) reductions in river dilution capacity due to climate change and water extractions. Using in-stream Biochemical Oxygen Demand (BOD) as an overall indicator of organic river pollution, we calculate historical (2000) and future (2050) BOD concentrations in global river networks. Despite significant self-cleaning capacities of rivers, the number of people affected by organic pollution (BOD >5 mg/l) is projected to increase from 1.1 billion in 2000 to 2.5 billion in 2050. With developing countries disproportionately affected, our results point to a growing need for affordable wastewater solutions.

Impacts of a high-discharge submarine sewage outfall on water quality in the coastal zone of Salvador (Bahia, Brazil).

Science.gov (United States)

Roth, F; Lessa, G C; Wild, C; Kikuchi, R K P; Naumann, M S

2016-05-15

Carbon and nitrogen stable isotopic signatures of suspended particulate organic matter and seawater biological oxygen demand (BOD) were measured along a coastal transect during summer 2015 to investigate pollution impacts of a high-discharge submarine sewage outfall close to Salvador, Brazil. Impacts of untreated sewage discharge were evident at the outfall site by depleted δ(13)Corg and δ(15)N signatures and 4-fold increased BOD rates. Pollution effects of a sewage plume were detectable for more than 6km downstream from the outfall site, as seasonal wind- and tide-driven shelf hydrodynamics facilitated its advective transport into near-shore waters. There, sewage pollution was detectable at recreational beaches by depleted stable isotope signatures and elevated BOD rates at high tides, suggesting high bacterial activity and increased infection risk by human pathogens. These findings indicate the urgent necessity for appropriate wastewater treatment in Salvador to achieve acceptable standards for released effluents and coastal zone water quality. Copyright © 2016 Elsevier Ltd. All rights reserved.

Organic pollution of rivers: Combined threats of urbanization, livestock farming and global climate change

Science.gov (United States)

Wen, Yingrong; Schoups, Gerrit; van de Giesen, Nick

2017-02-01

Organic pollution of rivers by wastewater discharge from human activities negatively impacts people and ecosystems. Without treatment, pollution control relies on a combination of natural degradation and dilution by natural runoff to reduce downstream effects. We quantify here for the first time the global sanitation crisis through its impact on organic river pollution from the threats of (1) increasing wastewater discharge due to urbanization and intensification of livestock farming, and (2) reductions in river dilution capacity due to climate change and water extractions. Using in-stream Biochemical Oxygen Demand (BOD) as an overall indicator of organic river pollution, we calculate historical (2000) and future (2050) BOD concentrations in global river networks. Despite significant self-cleaning capacities of rivers, the number of people affected by organic pollution (BOD >5 mg/l) is projected to increase from 1.1 billion in 2000 to 2.5 billion in 2050. With developing countries disproportionately affected, our results point to a growing need for affordable wastewater solutions.

Modeling of wastewater quality in an urban area during festival and rainy days.

Science.gov (United States)

Obaid, H A; Shahid, S; Basim, K N; Chelliapan, S

2015-01-01

Water pollution during festival periods is a major problem in all festival cities across the world. Reliable prediction of water pollution is essential in festival cities for sewer and wastewater management in order to ensure public health and a clean environment. This article aims to model the biological oxygen demand (BOD(5)), and total suspended solids (TSS) parameters in wastewater in the sewer networks of Karbala city center during festival and rainy days using structural equation modeling and multiple linear regression analysis methods. For this purpose, 34 years (1980-2014) of rainfall, temperature and sewer flow data during festival periods in the study area were collected, processed, and employed. The results show that the TSS concentration increases by 26-46 mg/l while BOD(5) concentration rises by 9-19 mg/l for an increase of rainfall by 1 mm during festival periods. It was also found that BOD(5) concentration rises by 4-17 mg/l for each increase of 10,000 population.

Impacts of a high-discharge submarine sewage outfall on water quality in the coastal zone of Salvador (Bahia, Brazil)

KAUST Repository

Roth, Florian

2016-03-30

Carbon and nitrogen stable isotopic signatures of suspended particulate organic matter and seawater biological oxygen demand (BOD) were measured along a coastal transect during summer 2015 to investigate pollution impacts of a high-discharge submarine sewage outfall close to Salvador, Brazil. Impacts of untreated sewage discharge were evident at the outfall site by depleted δ13Corg and δ15N signatures and 4-fold increased BOD rates. Pollution effects of a sewage plume were detectable for more than 6 km downstream from the outfall site, as seasonal wind- and tide-driven shelf hydrodynamics facilitated its advective transport into near-shore waters. There, sewage pollution was detectable at recreational beaches by depleted stable isotope signatures and elevated BOD rates at high tides, suggesting high bacterial activity and increased infection risk by human pathogens. These findings indicate the urgent necessity for appropriate wastewater treatment in Salvador to achieve acceptable standards for released effluents and coastal zone water quality.

On-site treatment of a motorway service area wastewater using a package sequencing batch reactor (SBR).

Science.gov (United States)

Del Solar, J; Hudson, S; Stephenson, T

2005-01-01

A sequencing batch reactor (SBR) treating the effluent of a motorway service station in the south of England situated on a major tourist route was investigated. Wastewater from the kitchens, toilets and washrooms facilities was collected from the areas on each side of the motorway for treatment on-site. The SBR was designed for a population equivalent (p.e.) of 500, assuming an average flow of 100 m3/d, influent biochemical oxygen demand (BOD) of 300 mg/l, and influent suspended solids (SS) of 300 mg/l. Influent monitoring over 8 weeks revealed that the average flow was only 65 m3/d and the average influent BOD and SS were 480 mg/l and 473 mg/l respectively. This corresponded to a high sludge loading rate (F:M) of 0.42 d(-1) which accounted for poor performance. Therefore the cycle times were extended from 6 h to 7 h and effluent BOD improved from 79 to 27 mg/l.

Water Quality Index in the Vicinity of Pelepah Kanan Mine, Kota Tinggi, Johor

International Nuclear Information System (INIS)

Wan Mohd Razi Idris; Sahibin Abdul Rahim; Mohd Talib Latif; Zulfahmi Ali Rahman; Tukimat Lihan; Chong, L.Y.; Azman Hashim; Shahrinizam Mohd Yusuf

2009-01-01

This study was carried out to determine the water quality index at the Pelepah Kanan River, Kota Tinggi, Johor. Six stations were chosen from different part of the river from upstream to downstream to represent the water quality index along this river. Three replicates of samples were taken from each station. Samples were collected in two different seasons namely dry season (July) and rainy season (December) 2007. In-situ physico-chemical measurements included temperature, ph, dissolved oxygen and conductivity. Physico-chemical parameters determined in the laboratory were turbidity, total suspended solid (TSS), biochemical oxygen demand (BOD), chemical oxygen demand (COD) and ammonia nitrogen (NH3-N). According to the Interim National Water Quality Standards (INWQS), results showed that all sampling stations along the Pelepah Kanan River in July fall in Class I-II for physical and chemical parameters except for dissolved oxygen and pH which was in Class I-II. The results obtained in December also showed that all sampling stations fall in Class I for physical and chemical parameters except for pH which was in Class III. Correlation test showed that some physico- chemical parameters have significant correlation with each other. Water Quality Index (WQI) analysis showed that the mean WQI value for the month of July is 96.88 (Class I) while for December, the WQI value deteriorated to 84.03 (Class II). According to the calculated values of WQI and comparison with INWQS, the index of water quality in Pelepah Kanan River is in the clean category and is not affected by pollution neither anthropogenic activities nor natural pollution. (author)

Physicochemical assessment of industrial textile effluents of Punjab (India)

Science.gov (United States)

Bhatia, Deepika; Sharma, Neeta Raj; Kanwar, Ramesh; Singh, Joginder

2018-06-01

Urbanization and industrialization are generating huge quantities of untreated wastewater leading to increased water pollution and human diseases in India. The textile industry is one of the leading polluters of surface water and consumes about 200-270 tons of water to produce 1 ton of textile product. The primary objective of the present study was to investigate the pollution potential of textile industry effluent draining into Buddha Nallah stream located in Ludhiana, Punjab (India), and determine the seasonal variation in physicochemical parameters (pH, water temperature, total dissolved solids, total suspended solids, biochemical oxygen demand (BOD) and chemical oxygen demand (COD) of Buddha Nallah water. During summer months, for Site 1 and Site 2, the value of pH was in the alkaline range of 8.78 ± 0.47 and 8.51 ± 0.41, respectively. The values of pH in the rainy season were found to be in the range of 7.38 ± 0.58 and 7.11 ± 0.59 for Site 1 and Site 2, respectively. In the autumn and winter seasons, the average pH values were found to be in the range of 8.58 ± 1.40 and 8.33 ± 0.970, respectively. The maximum mean temperature in summer was recorded as 41.16 ± 4.99 °C, and lowest mean temperature in winter was recorded as 39.25 ± 2.25 °C at Site 2. The suspended solids were found to be highest (143.5 ± 75.01 and 139.66 ± 71.87 mg/L) in autumn for both the sites and lowest (86.50 + 15.10 mg/L) in the rainy season for Site 1. The values of BOD and COD of the textile effluent of both sites during all the seasons ranged from 121-580 to 240-990 mg/L, respectively, much higher than WHO water quality standard of 30 mg/L for BOD and 250 mg/L for COD. The present study deals with the collection of textile industry effluent and its characterization to find out the physicochemical load being drained by the effluent generated from textile industries, on the natural wastewater streams.

Perspectives on Chemicals from Renewable Resources

NARCIS (Netherlands)

Scott, E.L.; Sanders, J.P.M.; Steinbuchel, A.

2009-01-01

Faced with increasing global demand for raw materials to meet the needs of transportation fuels, energy and chemical production coupled with depleting fossil reserves, fluctuating oil prices and ecological impact associated with CO2 emissions, there has been heightened awareness for the need to

Effect of Gamma Irradiation and Coagualtion on the Molegular Weight Distribution of Soluble Organic Substances in Paper Mill Effluent

International Nuclear Information System (INIS)

He Shijun; Wang Jianlong; Wan Jianxin; Sun Mengmeng; Ye Longfei

2012-01-01

In order to look into the insights of the influence of gamma irradiation and coagulation on the molecular weight distribution (MWD) of soluble organic substances in real paper mill effluent, various parameters of wastewater samples before and after treated were investigated, including chemical oxygen demand (COD), biochemical oxygen demand (BOD 5 ), dissolved organic carbon (DOC) and absorbance at 254 nm wavelength (UV 254 ) as well. In addition, the effects of irradiation on oxygen uptake and on acute toxicity were also presented. The results showed that irradiation alone cannot promote the biodegradability and oxygen uptake as originally expected. The whole acute toxicity of samples was reduced after gamma irradiation. On the other side, coagulation can not only effectively eliminate the sectors with high molecular weight (MW>3000 Dalton, in short HMW), but also improve the capacity of ionizing irradiation initiated the transformation of medium molecular weight (1000 Dalton< MW<3000 Dalton, in short MMW) into low molecular weight (MW<1000 Dalton, in short LWM), which is readily degraded by the subsequently activated sludge process. (author)

Effects of ferric ions on the catalytic ozonation process on sanitary landfill leachates

Directory of Open Access Journals (Sweden)

Messias Borges Silva

2013-04-01

Full Text Available Leachates exhibiting an unstable ratio of biochemical oxygen demand (BOD and chemical oxygen demand (COD of approximately 0.45 are typical of new landfills in the City of Cachoeira Paulista, Brazil. Although the organic matter portion is bio-treatable, the presence of refractory leached organic material requires unconventional effluent-treatment processes. Leachate treatment with ozone oxidation, in the presence of ferric ions, acts as catalyst in the formation of hydroxyl radicals. Ozone was obtained by corona-discharge from high-purity O2 gas. The treatment was performed in natura in a jacketed borosilicate glass reactor containing 900 ml of leachate. The analyzed response variable was expressed as the concentration of dissolved organic carbon (DOC. In order to determine the optimal proportions to produce the greatest degradation rate for organic materials, variations in experimental O2 flow-fed to the generator, the Fe(iii concentration, and the output of the ozonator were conducted over two experimental runs. Experimental models showed a DOC degradation on the order of 81.25%.

Treatment of real paracetamol wastewater by fenton process

Directory of Open Access Journals (Sweden)

Dalgic Gamze

2017-01-01

Full Text Available The study investigated the pretreatment of real paracetamol (PCT wastewater of a pharmaceutical industry by Fenton process. At the best experimental conditions (COD/H2O2 = 1/1, Fe+2/H2O2 = 1/70, settling method:centrifuging, pH 6 at settling step, 92.7, 92.7, 95.5, 99.1, 99.9 and 99.4% of chemical oxygen demand (COD, total organic carbon (TOC, 5-day biological oxygen demand (BOD5, PCT, para-amino phenol (PAP and aniline were removed, respectively. Changes in the concentrations of these parameters were also investigated for both oxidation and settling steps of Fenton process. It was found that COD and TOC were removed at the settling step (precipitation whereas PCT, PAP and aniline were removed at the oxidation step. Mass balance calculations were also studied to show the mass distributions of COD in different phases (gas + foam, effluent and sludge. Fenton process was found as an effective method for the pretreatment of real PCT wastewater for discharging in a determined collective treatment plant.

Effect of flow rate and disc area increment on the efficiency of rotating biological contactor for treating greywater

International Nuclear Information System (INIS)

Pathan, A.A.

2015-01-01

The performance of greywater treatment through RBC (Rotating Biological Contactor) is related to many factors including rotational speed of disc, surface area of the media, thickness of biological film; quality and flow rate of influent. The plastic media provides surface for biological slime. The slime is rotated alternatively into the settled wastewater and then into atmosphere to provide aerobic conditions for the microorganisms. In this study the performance of RBC is investigated at different flow rates and disk areas of media by introducing additional discs on the shaft of RBC. Initially efficiency of the RBC was observed on six flow rates at the disc area of 9.78m/sup 2/. Furthermore optimized three flow rates were used to augment the disk area. The efficiency of RBC system was improved significantly at disk area of 11.76m/sup 2/ and flow rate of 20 L/h. Under these conditions the removal of BOD5 (Biochemical Oxygen Demand) COD (Chemical Oxygen Demand) and TSS (Total Suspended Solid) was observed 83, 57 and 90% respectively. (author)

Effect of Gamma Irradiation and Coagualtion on the Molegular Weight Distribution of Soluble Organic Substances in Paper Mill Effluent

Energy Technology Data Exchange (ETDEWEB)

Shijun, He; Jianlong, Wang [Institute of Nuclear and New Energy Technology (INET), Tsinghua University, Beijing 100084 (China); Jianxin, Wan; Mengmeng, Sun [Institute of Nuclear and New Energy Technology (INET), Tsinghua University, Beijing 100084 (China); School of Resources and Environmental Engineering, Wuhan University of Technology, Wuhan 430070 (China); Longfei, Ye [Institute of Nuclear and New Energy Technology (INET), Tsinghua University, Beijing 100084 (China); College of Environmental Science and Engineering, Hunan University, Changsha, Hunan 410082 (China)

2012-07-01

In order to look into the insights of the influence of gamma irradiation and coagulation on the molecular weight distribution (MWD) of soluble organic substances in real paper mill effluent, various parameters of wastewater samples before and after treated were investigated, including chemical oxygen demand (COD), biochemical oxygen demand (BOD{sub 5}), dissolved organic carbon (DOC) and absorbance at 254 nm wavelength (UV{sub 254}) as well. In addition, the effects of irradiation on oxygen uptake and on acute toxicity were also presented. The results showed that irradiation alone cannot promote the biodegradability and oxygen uptake as originally expected. The whole acute toxicity of samples was reduced after gamma irradiation. On the other side, coagulation can not only effectively eliminate the sectors with high molecular weight (MW>3000 Dalton, in short HMW), but also improve the capacity of ionizing irradiation initiated the transformation of medium molecular weight (1000 Dalton

Performance evaluation of a hybrid system for efficient palm oil mill effluent treatment via an air-cathode, tubular upflow microbial fuel cell coupled with a granular activated carbon adsorption.

Science.gov (United States)

Tee, Pei-Fang; Abdullah, Mohammad Omar; Tan, Ivy Ai Wei; Mohamed Amin, Mohamed Afizal; Nolasco-Hipolito, Cirilo; Bujang, Kopli

2016-09-01

An air-cathode MFC-adsorption hybrid system, made from earthen pot was designed and tested for simultaneous wastewater treatment and energy recovery. Such design had demonstrated superior characteristics of low internal resistance (29.3Ω) and favor to low-cost, efficient wastewater treatment and power generation (55mW/m(3)) with average current of 2.13±0.4mA. The performance between MFC-adsorption hybrid system was compared to the standalone adsorption system and results had demonstrated great pollutants removals of the integrated system especially for chemical oxygen demand (COD), biochemical oxygen demand (BOD3), total organic carbon (TOC), total volatile solids (TVS), ammoniacal nitrogen (NH3-N) and total nitrogen (TN) because such system combines the advantages of each individual unit. Besides the typical biological and electrochemical processes that happened in an MFC system, an additional physicochemical process from the activated carbon took place simultaneously in the MFC-adsorption hybrid system which would further improved on the wastewater quality. Copyright © 2016 Elsevier Ltd. All rights reserved.

A cold plasma plume with a highly conductive liquid electrode

International Nuclear Information System (INIS)

Chen Guangliang; Chen Wenxing; Chen Shihua; Yang Size

2008-01-01

A cold dielectric barrier discharge (DBD) plasma plume with one highly conductive liquid electrode has been developed to treat thermally sensitive materials, and its preliminary discharging characteristics have been studied. The averaged electron temperature and density is estimated to be 0.6eV and 10 11 /cm 3 , respectively. The length of plasma plume can reach 5 cm with helium gas (He), and the conductivity of the outer electrode affects the plume length obviously. This plasma plume could be touched by bare hand without causing any burning or painful sensation, which may provide potential application for safe aseptic skin care. Moreover, the oxidative particles (e.g., OH, O * , O 3 ) in the downstream oxygen (O2) gas of the plume have been applied to treat the landfill leachate. The results show that the activated O 2 gas can degrade the landfill leachate effectively, and the chemical oxygen demand (COD), conductivity, biochemical oxygen demand (BOD), and suspended solid (SS) can be decreased by 52%, 57%, 76% and 92%, respectively. (fluids, plasmas and electric discharges)

Evaluation of the biological treatment for removal of color indigo textile industrial waste water by a microbial consortium in fluidized bed

International Nuclear Information System (INIS)

Quintero, Luz; Cardona, Santiago

2011-01-01

Water has been one of the most affected by industrialization and the development of the textile sector. Medellin is the fashion capital of Colombia and city daily use cleaners dedicated to clothing indigo dyeing. They are major consumers of ground and drinking water. Water is used with minimal consciousness, its increased raw material and which generates high monthly costs. This study was built (RLF) fluidized bed reactor. The anthracite was used as support material for investigating the efficiency removed of the chemical oxygen demand (COD), demand biochemical oxygen (BOD) and color of simulated textile wastewater. Following studies at laboratory scale were initially made to prepare the immobilization of microorganisms in the middle of solid support and periods of start-up and operation of the pilot plant testing: bioaugmentating and bioadaptacion seed taken from textile effluent and removal of color in discontinuous reactor. The results indicated that it is possible to achieve aerobic treatment of textile waste water after obtaining an inoculum adapted to sources of carbon of surfactants, and Indigo.

A Comprehensive Review on Water Quality Parameters Estimation Using Remote Sensing Techniques

Directory of Open Access Journals (Sweden)

Mohammad Haji Gholizadeh

2016-08-01

Full Text Available Remotely sensed data can reinforce the abilities of water resources researchers and decision makers to monitor waterbodies more effectively. Remote sensing techniques have been widely used to measure the qualitative parameters of waterbodies (i.e., suspended sediments, colored dissolved organic matter (CDOM, chlorophyll-a, and pollutants. A large number of different sensors on board various satellites and other platforms, such as airplanes, are currently used to measure the amount of radiation at different wavelengths reflected from the water’s surface. In this review paper, various properties (spectral, spatial and temporal, etc. of the more commonly employed spaceborne and airborne sensors are tabulated to be used as a sensor selection guide. Furthermore, this paper investigates the commonly used approaches and sensors employed in evaluating and quantifying the eleven water quality parameters. The parameters include: chlorophyll-a (chl-a, colored dissolved organic matters (CDOM, Secchi disk depth (SDD, turbidity, total suspended sediments (TSS, water temperature (WT, total phosphorus (TP, sea surface salinity (SSS, dissolved oxygen (DO, biochemical oxygen demand (BOD and chemical oxygen demand (COD.

Wastewater treatment in horizontal subsurface flow constructed wetlands using different media (setup stage

Directory of Open Access Journals (Sweden)

Abdel Razik A. Zidan

2015-04-01

Full Text Available Wastewater treatment through horizontal subsurface flow (HSSF constructed wetlands (CWs using three different treatment media (gravel, pieces of plastic pipes, and shredded tire rubber chips were investigated in Samaha village, Dakahliya, Egypt. The study focused on the wetland setup stage during the first months of its operation (setup stage. In this stage media porosity, bacterial biofilm, and plant roots growth were in progress and it was prior to the operational steady state stage. Objectives of this paper are to study the change in media porosity of HSSF wetland cells in order to estimate duration of wetland setup stage, and to evaluate the use of different bed media on biological oxygen demand (BOD, chemical oxygen demand (COD and total suspended solids (TSS treatment. The results showed that after 180 days of operation, the wetland cells had reached steady porosity and had started stable treatment. Also performance of plastic media bed in pollutants reduction was better than gravel and rubber beds and gravel media was in advanced than rubber media.

The Water Quality Study and Sources of Pollution in Alur Ilmu, UKM

International Nuclear Information System (INIS)

Nurul Afina Abd Mutalib; Othman Abdul Karim

2015-01-01

The Alur Ilmu UKM is a large storm water channel that serves to store water and flows into Langat River. The primary objective of this study are to identify the water quality and pollution levels, the sources of which may cause pollution and to measures the control pollution that occurs in the area. Water sampling was carried out in order to determine the quality of water. The sampling water was taken during no-rain and after rainfall. The area includes UKM Forest Reserve (Hutan Pendidikan Alam - HPA), Student Cafeteria (Teres Eko Niaga), Restaurant of Fakulti Sains dan Teknologi (FST), Student Centre (Pusanika), Fakulti Pendidikan Islam (FPI) and UKM Mosque. Eight water quality parameters for example consisting of Biochemical Oxygen Demand (BOD), Chemical Oxygen Demand (COD), pH, Turbidity, Total Suspended Solids (TSS), Total Kjeldahl Nitrogen (TKN), Temperature, Oil and Grease were measured. The results shows that the water quality are in a class III and IV according to Water quality Index (WQI) and the water meet the standard B that set out in the Regulations of the Environmental Quality (Sewage and Effluent). (author)

A comprehensive review on utilization of wastewater from coffee processing.

Science.gov (United States)

Rattan, Supriya; Parande, A K; Nagaraju, V D; Ghiwari, Girish K

2015-05-01

The coffee processing industry is one of the major agro-based industries contributing significantly in international and national growth. Coffee fruits are processed by two methods, wet and dry process. In wet processing, coffee fruits generate enormous quantities of high strength wastewater requiring systematic treatment prior to disposal. Different method approach is used to treat the wastewater. Many researchers have attempted to assess the efficiency of batch aeration as posttreatment of coffee processing wastewater from an upflow anaerobic hybrid reactor (UAHR)-continuous and intermittent aeration system. However, wet coffee processing requires a high degree of processing know-how and produces large amounts of effluents which have the potential to damage the environment. Characteristics of wastewater from coffee processing has a biological oxygen demand (BOD) of up to 20,000 mg/l and a chemical oxygen demand (COD) of up to 50,000 mg/l as well as the acidity of pH below 4. In this review paper, various methods are discussed to treat coffee processing wastewaters; the constitution of wastewater is presented and the technical solutions for wastewater treatment are discussed.

Application of the Microtox test and pollution indices to the study of water toxicity in the Albufera Natural Park (Valencia, Spain).

Science.gov (United States)

Boluda, R; Quintanilla, J F; Bonilla, J A; Sáez, E; Gamón, M

2002-01-01

The toxic effects of waters collected from irrigation channels in a Mediterranean wetland (Albufera Natural Park, Valencia, Spain) were tested with the Microtox assay and compared with six pollution indices (PIs) defined from analytical parameters. Chemical oxygen demand (COD), biological oxygen demand (BOD), nutrients, heavy metals and pesticides were measured. The bioassay result (concentrations of the water sample (% V/V) that reduced light emission to 10%, 20% and 50%, EC10, EC20 and EC50, respectively (ECs)) was compared with the PIs. This comparison has demonstrated a general agreement between ECs and PIs, except in the case of irrigation channels affected by herbicides used in rice farming (molinate and thiobencarb). No pronounced inhibition was detected in the bioluminescence in relation to the eutrophic parameters in the irrigation waters for EC50 values, indicating that this parameter does not suffice to detect eutrophic waters. Data derived from irrigation water pollution and bioassay were assembled by multivariate statistical techniques (principal component analysis). These components were associated with various contamination sources.

40 CFR 403.15 - Net/Gross calculation.

Science.gov (United States)

2010-07-01

... pollutants in the intake waters. (2) Credit for generic pollutants such as biochemical oxygen demand (BOD... to obtain credit for intake pollutants must make application to the Control Authority. Upon request... to reflect credit for pollutants in the intake water) if the requirements of paragraph (b) of this...

PERFECT DEMAND ILLUSION

Directory of Open Access Journals (Sweden)

Alexander Yu. Sulimov

2015-01-01

Full Text Available The article is devoted to technique «Perfect demand illusion», which allows to strengthen the competitive advantageof retailers. Also in the paper spells out the golden rules of visual merchandising.The definition of the method «Demand illusion», formulated the conditions of its functioning, and is determined by the mainhypothesis of the existence of this method.Furthermore, given the definition of the «Perfect demand illusion», and describes its additional conditions. Also spells out the advantages of the «Perfect demandillusion», before the «Demand illusion».

Electricity demand in Kazakhstan

International Nuclear Information System (INIS)

Atakhanova, Zauresh; Howie, Peter

2007-01-01

Properties of electricity demand in transition economies have not been sufficiently well researched mostly due to data limitations. However, information on the properties of electricity demand is necessary for policy makers to evaluate effects of price changes on different consumers and obtain demand forecasts for capacity planning. This study estimates Kazakhstan's aggregate demand for electricity as well as electricity demand in the industrial, service, and residential sectors using regional data. Firstly, our results show that price elasticity of demand in all sectors is low. This fact suggests that there is considerable room for price increases necessary to finance generation and distribution system upgrading. Secondly, we find that income elasticity of demand in the aggregate and all sectoral models is less than unity. Of the three sectors, electricity demand in the residential sector has the lowest income elasticity. This result indicates that policy initiatives to secure affordability of electricity consumption to lower income residential consumers may be required. Finally, our forecast shows that electricity demand may grow at either 3% or 5% per year depending on rates of economic growth and government policy regarding price increases and promotion of efficiency. We find that planned supply increases would be sufficient to cover growing demand only if real electricity prices start to increase toward long-run cost-recovery levels and policy measures are implemented to maintain the current high growth of electricity efficiency

Photocatalytic pretreatment of oily wastewater from the restaurant by a vacuum ultraviolet/TiO2 system

International Nuclear Information System (INIS)

Kang Jianxiong; Lu Lu; Zhan Wei; Li Bo; Li Daosheng; Ren Yongzheng; Liu Dongqi

2011-01-01

The present study aims at investigating the performance of a vacuum ultraviolet (VUV, 185 nm) and TiO 2 oxidation system for the pretreatment of oily wastewater from restaurant. The influence of irradiation time, pH, dissolved oxygen (DO), the dosage of TiO 2 and the initial chemical oxygen demand (COD) concentration on COD removal efficiency was ascertained and optimum process conditions for stable and effective operation were determined. Under the optimum conditions of irradiation 10 min, initial COD 3981 mg/L, TiO 2 150 mg/L, pH 7.0 and flow rate of air 40 L/h, the process of VUV and TiO 2 /VUV achieved removal efficiencies of COD, BOD 5 and oil as 50 ± 3%, 37 ± 2%, 86 ± 3%, and 63 ± 3%, 43 ± 2%, 70 ± 3%, respectively. The biodegradability factor f B of the wastewater was determined as 1.56 which indicated that the VUV/TiO 2 process improved the biodegradability of the oily wastewater significantly. Results clearly indicate that VUV/TiO 2 photolysis tends to destruct parts of COD, BOD 5 , and ammonia, as well as enhances the biodegradability of the oily wastewater simultaneously. Thus, this technique could be used as a pretreatment step for conventional biological treatment of oily wastewater.

Implementation of Extended Statistical Entropy Analysis to the Effluent Quality Index of the Benchmarking Simulation Model No. 2

Directory of Open Access Journals (Sweden)

Alicja P. Sobańtka

2014-01-01

Full Text Available Extended statistical entropy analysis (eSEA is used to assess the nitrogen (N removal performance of the wastewater treatment (WWT simulation software, the Benchmarking Simulation Model No. 2 (BSM No. 2 . Six simulations with three different types of wastewater are carried out, which vary in the dissolved oxygen concentration (O2,diss. during the aerobic treatment. N2O emissions generated during denitrification are included in the model. The N-removal performance is expressed as reduction in statistical entropy, ΔH, compared to the hypothetical reference situation of direct discharge of the wastewater into the river. The parameters chemical and biological oxygen demand (COD, BOD and suspended solids (SS are analogously expressed in terms of reduction of COD, BOD, and SS, compared to a direct discharge of the wastewater to the river (ΔEQrest. The cleaning performance is expressed as ΔEQnew, the weighted average of ΔH and ΔEQrest. The results show that ΔEQnew is a more comprehensive indicator of the cleaning performance because, in contrast to the traditional effluent quality index (EQ, it considers the characteristics of the wastewater, includes all N-compounds and their distribution in the effluent, the off-gas, and the sludge. Furthermore, it is demonstrated that realistically expectable N2O emissions have only a moderate impact on ΔEQnew.

Photocatalytic pretreatment of oily wastewater from the restaurant by a vacuum ultraviolet/TiO2 system.

Science.gov (United States)

Kang, Jian-xiong; Lu, Lu; Zhan, Wei; Li, Bo; Li, Dao-sheng; Ren, Yong-zheng; Liu, Dong-qi

2011-02-15

The present study aims at investigating the performance of a vacuum ultraviolet (VUV, 185 nm) and TiO(2) oxidation system for the pretreatment of oily wastewater from restaurant. The influence of irradiation time, pH, dissolved oxygen (DO), the dosage of TiO(2) and the initial chemical oxygen demand (COD) concentration on COD removal efficiency was ascertained and optimum process conditions for stable and effective operation were determined. Under the optimum conditions of irradiation 10 min, initial COD 3981 mg/L, TiO(2) 150 mg/L, pH 7.0 and flow rate of air 40 L/h, the process of VUV and TiO(2)/VUV achieved removal efficiencies of COD, BOD(5) and oil as 50±3%, 37±2%, 86±3%, and 63±3%, 43±2%, 70±3%, respectively. The biodegradability factor f(B) of the wastewater was determined as 1.56 which indicated that the VUV/TiO(2) process improved the biodegradability of the oily wastewater significantly. Results clearly indicate that VUV/TiO(2) photolysis tends to destruct parts of COD, BOD(5), and ammonia, as well as enhances the biodegradability of the oily wastewater simultaneously. Thus, this technique could be used as a pretreatment step for conventional biological treatment of oily wastewater. Copyright © 2010 Elsevier B.V. All rights reserved.

Water Quality Degradation and Management Strategies for Swine and Rice Farming Wastewater in the Tha Chin River Basin

Directory of Open Access Journals (Sweden)

Abigail Henderson

2017-11-01

Full Text Available Water quality in the Tha Chin River regularly exceeds biological oxygen demand (BOD standards of Thailand’s Enhancement and Conservation of National Environmental Quality Act. This study quantified the BOD loading from rice cultivation and swine farming to the Tha Chin River using effluent data and procedures from the Pollution Control Department (PCD, geospatial land-use maps from the Land Development Department, and water quality data from the Ministry of Natural Resources and the Environment. It was determined that the BOD loading was 12 tons/day from swine farming in 2015 and 52 tons/day, on average, from rice farming between 2002 and 2011. Technology-specific, community-scale wastewater management strategies were recommended for both industries: feasibility studies revealed 66 potential sites for constructed wetland implementation and 7 subdistricts suitable for biogas network pipelines. It was determined that if these projects are implemented in conjunction, the BOD would be reduced by 6% (0.3 mg/L in the entire river or 11% (0.5 mg/L at the three water quality monitoring stations proximate to swine farms. These reductions would have a substantial effect on the water quality of the Tha Chin River, and governmental agencies such as the PCD should strongly consider subsidization and implementation of these projects.

Stochastic modeling for river pollution of Sungai Perlis

International Nuclear Information System (INIS)

Yunus, Nurul Izzaty Mohd.; Rahman, Haliza Abd.; Bahar, Arifah

2015-01-01

River pollution has been recognized as a contributor to a wide range of health problems and disorders in human. It can pose health dangers to humans who come into contact with it, either directly or indirectly. Therefore, it is most important to measure the concentration of Biochemical Oxygen Demand (BOD) as a water quality parameter since the parameter has long been the basic means for determining the degree of water pollution in rivers. In this study, BOD is used as a parameter to estimate the water quality at Sungai Perlis. It has been observed that Sungai Perlis is polluted due to lack of management and improper use of resources. Therefore, it is of importance to model the Sungai Perlis water quality in order to describe and predict the water quality systems. The BOD concentration secondary data set is used which was extracted from the Drainage and Irrigation Department Perlis State website. The first order differential equation from Streeter – Phelps model was utilized as a deterministic model. Then, the model was developed into a stochastic model. Results from this study shows that the stochastic model is more adequate to describe and predict the BOD concentration and the water quality systems in Sungai Perlis by having smaller value of mean squared error (MSE)

Stochastic modeling for river pollution of Sungai Perlis

Energy Technology Data Exchange (ETDEWEB)

Yunus, Nurul Izzaty Mohd.; Rahman, Haliza Abd. [Department of Mathematical Sciences, Faculty of Science, Universiti Teknologi Malaysia,81310 Johor Bahru, Johor (Malaysia); Bahar, Arifah [UTM-Centre of Industrial and Applied Mathematics (UTM-CIAM) Universiti Teknologi Malaysia, 81310 Johor Bahru, Johor (Malaysia)

2015-02-03

River pollution has been recognized as a contributor to a wide range of health problems and disorders in human. It can pose health dangers to humans who come into contact with it, either directly or indirectly. Therefore, it is most important to measure the concentration of Biochemical Oxygen Demand (BOD) as a water quality parameter since the parameter has long been the basic means for determining the degree of water pollution in rivers. In this study, BOD is used as a parameter to estimate the water quality at Sungai Perlis. It has been observed that Sungai Perlis is polluted due to lack of management and improper use of resources. Therefore, it is of importance to model the Sungai Perlis water quality in order to describe and predict the water quality systems. The BOD concentration secondary data set is used which was extracted from the Drainage and Irrigation Department Perlis State website. The first order differential equation from Streeter – Phelps model was utilized as a deterministic model. Then, the model was developed into a stochastic model. Results from this study shows that the stochastic model is more adequate to describe and predict the BOD concentration and the water quality systems in Sungai Perlis by having smaller value of mean squared error (MSE)

The Effect of H2O2 Interference in Chemical Oxygen Demand Removal During Advanced Oxidation Processes

Directory of Open Access Journals (Sweden)

Afsane Chavoshani

2016-07-01

Full Text Available Hydrogen peroxide (H2O2 is one of the most oxidants in AOPs. By H2O2 dissociation, hydroxyl radical with a standard oxidation potential of 2.7 is produced. It is reported H2O¬ residual in AOPs has been led to interference in chemical oxygen demand (COD test and it is able to hinder biological treatment of waste water. Because of high mixed organic load of solid waste leachate, this study investigated effect of H2O2 interference in COD removal from solid waste leachate. In this study effect of parameters such as pH (3,5,7,12, H2O2 dose (0.01, 0.02, 0.03, 0.04 mol l-1, and time reaction(10,20,30,40,50,60 min evaluated on H2O2 interference in COD removal from solid waste leachate. Optimum pH and concentration were 3 and 0.02 moll-1 respectively. With increasing reaction time, COD removal was increased. The false COD obtained between 0.49mg per 1mg of H2O2. The average of COD removal by H2O2 for 60 min was 6.57%. Also reaction rate of this process was 0.0029 min-1. The presence of H2O2 leads to overestimation of COD values after reaction time because it consumes the oxidation agent. The extent of H2O2 interference in COD analysis was proportional to the remaining H2O2 concentration at the moment of sampling.

Upgrading secondary wastewater plant effluent by modified coagulation and flocculation, for water reuse in irrigation

Directory of Open Access Journals (Sweden)

Mohammad Taghi Ghaneian

2017-09-01

Full Text Available In this study, the feasibility of using coagulation, flocculation, and sedimentation (CF-S for advanced treatment of secondary effluent released from the Yazd Intermittent Cycle Extended Aeration System was investigated. Four coagulants including ferric chloride (FeCl3, polyaluminum chloride (PAC, ferrous sulfate (FeSo4, and potassium ferrate (K2FeSo4 along with Gflog C-150 as flocculant polymer were used. In this study, returned chemical sludge was considered as a modification. Preliminary CF-S processes showed that FeSO4 and K2FeO4 had low removal efficiencies. Thus, these two coagulants were abandoned and CF-S processes were continued only with PAC and FeCl3 coagulants which had higher efficiencies in the removal of biological oxygen demand (BOD5, chemical oxygen demand (COD, total suspended solids (TSS, and turbidity. Removal efficiency was higher when half of the chemical producing sludge was returned as compared with using both coagulants simultaneously along with 2 mg L−1 of C-150 as flocculant. In the optimum dosage, when half of PAC and FeCl3 sludge were returned, the volume of produced sludge was reduced by 40% and 28%, respectively, as compared without returned sludge. For the PAC coagulant in the optimum dosage with half of the sludge returned, all 2012 EPA standards of irrigation were met for both ‘processed and non-processed type’ agricultural crops.

Forecast electricity demand in Quebec: Development plan 1993

International Nuclear Information System (INIS)

1992-01-01

Demographic, economic, and energy prospects are the determining factors in estimating demand for electricity in Quebec. In average scenarios developed for 1992-2010, the Quebec population will grow 0.5%/y and the gross domestic product will increase 2.6%/y. Firm electricity sales by Hydro-Quebec will grow to 197.9 TWh by 2010, or 2.2%/y. Sales in the residential and farm sectors should grow 1.3%/y and sales in the general and institutional sectors should rise by 2.2%/y. Electricity demand in the industrial sector, rising at an estimated 2.9%/y in 1992-2010, is chiefly responsible for the anticipated growth in Hydro-Quebec's overall sales. The nonferrous smelting, refining, chemicals, and paper industries will account for ca 60% of this growth. In the municipal services and public transportation sectors, demand should grow 3.3%/y, and over half the growth forecast in this sector can be attributed to the impact that new uses of electricity are expected to have after 2005. High- and low-growth scenarios offer alternative visions of demand growth based on different but equally valid assumptions about demographic and economic growth. In terms of firm electricity sales, the high- and low-growth scenarios differ by 50 TWh in 2010. Hydro-Quebec has retained two strategic orientations that will influence growth in electricity sales: the development of industrial markets and extension of the energy-savings objective of 9.3 TWh forecast to the year 2000. Taking these two orientations into account, the growth rate for electricity sales in the average scenario would be 1.8%/y rather than 2.2%/y. 25 figs., 81 tabs

Electricity demand forecasting techniques

International Nuclear Information System (INIS)

Gnanalingam, K.

1994-01-01

Electricity demand forecasting plays an important role in power generation. The two areas of data that have to be forecasted in a power system are peak demand which determines the capacity (MW) of the plant required and annual energy demand (GWH). Methods used in electricity demand forecasting include time trend analysis and econometric methods. In forecasting, identification of manpower demand, identification of key planning factors, decision on planning horizon, differentiation between prediction and projection (i.e. development of different scenarios) and choosing from different forecasting techniques are important

Determining TOC in Waters

Science.gov (United States)

Kehoe, Thomas J.

1977-01-01

The instrumental method for detecting total organic carbon (TOC) in water samples is detailed. The method's limitations are discussed and certain precautions that must be taken are emphasized. The subject of TOC versus COD and BOD is investigated and TOC is determined to be a valid indication of biological demand. (BT)

40 CFR 417.161 - Specialized definitions.

Science.gov (United States)

2010-07-01

... line to maintain minimal product quality. (f) The term BOD7 shall mean the biochemical oxygen demand as... apply to this subpart. (b) The term anhydrous product shall mean the theoretical product that would result if all water were removed from the actual product. (c) The term surfactant shall mean those...

Effect of abattoir wastes on the water quality of Aleto River in the ...

African Journals Online (AJOL)

The effects of abattoir effluent on the water quality parameters, pH, dissolved oxygen, nitrate (NO3), phosphate (PO4), sulphate (SO4), hardness, conductivity, faecal coliform and the biochemical oxygen demand (BOD), of the receiving surface water of Aleto River in River State (Niger Delta, Nigeria) was monitored monthly ...

Physical and Chemical Characteristics of Lake Edku Water, Egypt

Directory of Open Access Journals (Sweden)

M.A. OKBAH

2002-12-01

Full Text Available The objective of this work is to evaluate the quality of Lake Edku water. Regional and seasonal variations of some physico-chemical parameters (nutrient salts, total nitrogen, total phosphorous and silicate, in addition to pH, total alkalinity, chlorosity, dissolved oxygen, biological oxygen demand and oxidizable organic matter that were determined during the period from January to December 2000. Important variations have occurred in the investigated area as a result of human activity and the discharge of wastewater to the lake. The relatively low pH values reflect the decreased productivity of the Lake as a result of the polluted water discharged into the lake. Total alkalinity varied between 2.25 ± 0.35 to 8.38 ± 0.9 meq/l. In comparison with previous decades chlorosity content (586-1562 mg/l showed the general decreasing trend. Dissolved oxygen varied (2.37 ± 0.72 - 4.47 ± 0.94 mg/l. The ratios of BOD/ OOM values indicate that the lake water has a biodegradable nature. There was a noticeable variation in ammonia levels; a lower ammonia content was recorded in summer and spring. Nitrite and nitrate concentrations in Lake Edku water showed values ranging from 3.7±1.4 to 7.8±1.9 ΜM and from 15.2±2.9 to 45.9±11.8 ΜM, respectively. The total nitrogen of the lake exhibited higher levels (53.1±12.2 – 164.2±30.7 ΜM. The ratio of NH4/TIN (0.09-0.45 seems to be highly representative of the microbial nitrification rate as well as of the varying agricultural inflows. It is interesting to note that increasing values of reactive phosphate (11.6±1.8 – 14.7±2.5 ΜM were determined in autumn and winter respectively. The higher concentrations of reactive silicate were directly proportional to drainage water discharged into the Lake. It is clear from the mean ratio of N/P (2.4-8.8 nitrogen is the limiting factor. The lower values of N/P ratio could be related to an allochthonous condition.

Forecasting global developments in the basic chemical industry for environmental policy analysis

NARCIS (Netherlands)

Broeren, M.L.M.|info:eu-repo/dai/nl/371687438; Saygin, D.; Patel, M.K.

The chemical sector is the largest industrial energy user, but detailed analysis of its energy use developments lags behind other energy-intensive sectors. A cost-driven forecasting model for basic chemicals production is developed, accounting for regional production costs, demand growth and stock

Progress of Mimetic Enzymes and Their Applications in Chemical Sensors.

Science.gov (United States)

Yang, Bin; Li, Jianping; Deng, Huan; Zhang, Lianming

2016-11-01

The need to develop innovative and reformative approaches to synthesize chemical sensors has increased in recent years because of demands for selectivity, stability, and reproducibility. Mimetic enzymes provide an efficient and convenient method for chemical sensors. This review summarizes the application of mimetic enzymes in chemical sensors. Mimetic enzymes can be classified into five categories: hydrolases, oxidoreductases, transferases, isomerases, and induced enzymes. Potential and recent applications of mimetic enzymes in chemical sensors are reviewed in detail, and the outlook of profound development has been illustrated.

Application of electrochemically synthesized ferrate(VI in the purification of wastewater from coal separation plant

Directory of Open Access Journals (Sweden)

Čekerevac Milan I.

2010-01-01

Full Text Available The oxidative and coagulation efficiency of Na2FeO4 solution, electrochemically generated by trans-passive anodic oxidation of electrical steel in 10M NaOH solution, is confirmed in the process of purification of heavily contaminated wastewater from coal separation plant. The decontamination efficiency is evaluated comparing the values of selected contamination parameters obtained by chemical and biochemical analysis of plant effluent water and water obtained after decontamination with ferrate(VI solution in relatively simple laboratory procedure. The sample of 450 ml of wastewater is treated in laboratory conditions with 100cm3 solution of 1 mg dm-3 Na2FeO4 in 10M NaOH. The chemical analysis of effluent water after treatment have shown almost 3 times lower permanganate index, about 3 times lower iron content, 1.45 times lower As3+ content, 7.35 times lower ammonia content. Turbidity and chemical oxygen demand (COD is reduced for more than 5.77and 13.4 times, respectively. The suspended and colloid matter is eliminated from effluent water after treatment with ferrate(VI solution. Also, biochemical exploration has confirmed high efficiency of ferrate(VI in organics and microbial elimination showing 7.1 times lower 5-days bio-chemical oxygen demand (BOD5, and total elimination of aerobic and anaerobic bacteria from effluent water. According to standards on quality of industrial wastewater effluents, it may be concluded that ferrate(VI treatment of wastewater almost completely eliminates excess of dangerous chemicals and pathogen bacteria, with the exemption of arsenic. Thus, ferrate(VI shows capable performance in treatment of coal separation plant wastewater.

Demand response in energy markets

International Nuclear Information System (INIS)

Skytte, K.; Birk Mortensen, J.

2004-11-01

Improving the ability of energy demand to respond to wholesale prices during critical periods of the spot market can reduce the total costs of reliably meeting demand, and the level and volatility of the prices. This fact has lead to a growing interest in the short-run demand response. There has especially been a growing interest in the electricity market where peak-load periods with high spot prices and occasional local blackouts have recently been seen. Market concentration at the supply side can result in even higher peak-load prices. Demand response by shifting demand from peak to base-load periods can counteract the market power in the peak-load. However, demand response has so far been modest since the current short-term price elasticity seems to be small. This is also the case for related markets, for example, green certificates where the demand is determined as a percentage of the power demand, or for heat and natural gas markets. This raises a number of interesting research issues: 1) Demand response in different energy markets, 2) Estimation of price elasticity and flexibility, 3) Stimulation of demand response, 4) Regulation, policy and modelling aspects, 5) Demand response and market power at the supply side, 6) Energy security of supply, 7) Demand response in forward, spot, ancillary service, balance and capacity markets, 8) Demand response in deviated markets, e.g., emission, futures, and green certificate markets, 9) Value of increased demand response, 10) Flexible households. (BA)

History of demand side management and classification of demand response control schemes

NARCIS (Netherlands)

Lampropoulos, I.; Kling, W.L.; Ribeiro, P.F.; Berg, van den J.

2013-01-01

The scope of this paper is to provide a review on the topic of demand side management. A historical overview provides a critical insight to applied cases, while the discovery of new evidence calls for reconsideration of the design of demand response control schemes. The developments at the demand

Quantitative work demands, emotional demands, and cognitive stress symptoms in surgery nurses.

Science.gov (United States)

Elfering, Achim; Grebner, Simone; Leitner, Monika; Hirschmüller, Anja; Kubosch, Eva Johanna; Baur, Heiner

2017-06-01

In surgery, cognitive stress symptoms, including problems in concentrating, deciding, memorising, and reflecting are risks to patient safety. Recent evidence points to social stressors as antecedents of cognitive stress symptoms in surgery personnel. The current study tests whether cognitive stress symptoms are positively associated with emotional abuse, emotional- and task-related demands and resources in surgery work. Forty-eight surgery nurses from two hospitals filled out the Copenhagen Psychosocial Questionnaire in its German version. Task-related and emotional demands were positively related to cognitive stress symptoms. In a stepwise, multiple, linear regression of cognitive stress symptoms on task-related and emotional demands, emotional abuse and emotional demands were unique predictors (p emotional abuse, emotional demands, and, therefore, communication and cooperation team climate in surgery personnel.

Road infrastructure and demand induction

DEFF Research Database (Denmark)

Nielsen, Thomas Alexander Sick; Hovgesen, Henrik Harder; Lahrmann, Harry

2006-01-01

a long screenline is used to measure the development in aggregate demand in selected corridors. The paper analyses demand induction by establishing time series of aggregate demand that is compared with the national traffic index. Significant trend breaks in the association between aggregate demand...... in the corridors and the national index, following the opening of motorways or bridges, indicates demand induction by infrastructure expansion in a number of instances. Lack of significant trend breaks following opening year is found in peripheral areas where major population centres are missing. This indicates...... the necessity of some latent demand within suitable travel range for new infrastructure elements to produce significant amounts of induced demand. Estimates of demand induction as a percentage of the realised demand five years after opening are between 10% and 67% for new motorway sections depending...

Application of integrated ozone and granular activated carbon for decolorization and chemical oxygen demand reduction of vinasse from alcohol distilleries.

Science.gov (United States)

Hadavifar, Mojtaba; Younesi, Habibollah; Zinatizadeh, Ali Akbar; Mahdad, Faezeh; Li, Qin; Ghasemi, Zahra

2016-04-01

This study investigates the treatment of the distilleries vinasse using a hybrid process integrating ozone oxidation and granular activated carbons (GAC) in both batch and continuous operation mode. The batch-process studies have been carried out to optimize initial influent pH, GAC doses, the effect of the ozone (O3) and hydrogen peroxide (H2O2) concentrations on chemical oxygen demand (COD) and color removal of the distilleries vinasse. The continuous process was carried out on GAC and ozone treatment alone as well as the hybrid process comb both methods to investigate the synergism effectiveness of the two methods for distilleries vinasse COD reduction and color removal. In a continuous process, the Yan model described the experimental data better than the Thomas model. The efficiency of ozonation of the distilleries vinasse was more effective for color removal (74.4%) than COD removal (25%). O3/H2O2 process was not considerably more effective on COD and color removal. Moreover, O3/GAC process affected negatively on the removal efficiency by reducing COD and color from distilleries vinasse. The negative effect decreased by increasing pH value of the influent. Copyright © 2016 Elsevier Ltd. All rights reserved.

An integrated mathematical model for chemical oxygen demand (COD) removal in moving bed biofilm reactors (MBBR) including predation and hydrolysis.

Science.gov (United States)

Revilla, Marta; Galán, Berta; Viguri, Javier R

2016-07-01

An integrated mathematical model is proposed for modelling a moving bed biofilm reactor (MBBR) for removal of chemical oxygen demand (COD) under aerobic conditions. The composite model combines the following: (i) a one-dimensional biofilm model, (ii) a bulk liquid model, and (iii) biological processes in the bulk liquid and biofilm considering the interactions among autotrophic, heterotrophic and predator microorganisms. Depending on the values for the soluble biodegradable COD loading rate (SCLR), the model takes into account a) the hydrolysis of slowly biodegradable compounds in the bulk liquid, and b) the growth of predator microorganisms in the bulk liquid and in the biofilm. The integration of the model and the SCLR allows a general description of the behaviour of COD removal by the MBBR under various conditions. The model is applied for two in-series MBBR wastewater plant from an integrated cellulose and viscose production and accurately describes the experimental concentrations of COD, total suspended solids (TSS), nitrogen and phosphorous obtained during 14 months working at different SCLRs and nutrient dosages. The representation of the microorganism group distribution in the biofilm and in the bulk liquid allow for verification of the presence of predator microorganisms in the second reactor under some operational conditions. Copyright © 2016 Elsevier Ltd. All rights reserved.

Innovative technology to meet the demands of the white biotechnology revolution of chemical production

DEFF Research Database (Denmark)

Villadsen, John

2007-01-01

by which a technological revolution termed "white biotechnology" for production of commodity chemicals has proved its credibility. Obviously, the rapid advances in biology has been crucial for the development of industrial biotechnology towards a position where even its cheap products such as bio-fuels can...... of sophisticated models, supported by accurate data obtained in experimental equipment that did not exist a few years ago. The need to update the chemical engineering education to meet the needs of the bio-industry is also evident. Much of the progress of the bio-industry has up to now been based on fundamental...

The development of demand elasticity model for demand response in the retail market environment

NARCIS (Netherlands)

Babar, M.; Nguyen, P.H.; Kamphuis, I.G.

2015-01-01

In the context of liberalized energy market, increase in distributed generation, storage and demand response has expanded the price elasticity of demand, thus causing the addition of uncertainty to the supply-demand chain of power system. In order to cope with the challenges of demand uncertainty

Improving Chemical Plant Safety Training Using Virtual Reality

OpenAIRE

Nasios, Konstantinos

2002-01-01

The chemical engineering industry often requires people to work in hazardous environments and to operate complicated equipment which often limits the type of training that be carried out on site. The daily job of chemical plant operators is becoming more demanding due to the increasing plant complexity together with increasing requirements on plant safety, production capacity, product quality and cost effectiveness. The importance of designing systems and environments that are as safe as poss...

Environmental chemistry and ecotoxicology: in greater demand than ever.

Science.gov (United States)

Scheringer, Martin

2017-01-01

Environmental chemistry and ecotoxicology have been losing support, resources, and recognition at universities for many years. What are the possible causes of this process? A first problem may be that the need for research and teaching in environmental chemistry and ecotoxicology is no longer seen because chemical pollution problems are considered as largely solved. Second, environmental chemistry and ecotoxicology may be seen as fields dominated by routine work and where there are not many interesting research questions left. A third part of the problem may be that other environmental impacts such as climate change are given higher priority than chemical pollution problems. Here, several cases are presented that illustrate the great demand for innovative research and teaching in environmental chemistry and ecotoxicology. It is crucial that environmental chemistry and ecotoxicology are rooted in academic science and are provided with sufficient equipment, resources, and prospects for development.

Hydrogen peroxide-enhanced iron-mediated aeration for the treatment of mature landfill leachate.

Science.gov (United States)

Deng, Yang; Englehardt, James D

2008-05-01

Municipal landfill leachate is being disallowed for biological treatment by some sewer authorities due to its recalcitrance and corrosiveness, and therefore physicochemical treatment may be needed. In this paper, hydrogen peroxide-enhanced iron (Fe(0))-mediated aeration (IMA) was studied as an alternative for the treatment of mature landfill leachate. Bench-scale Taguchi array screening tests and full factorial tests were conducted. Iron grade, initial pH, H(2)O(2) addition rate, and aeration rate significantly influenced both overall chemical oxygen demand (COD) removal and iron consumption. In the enhanced IMA-treated leachate at an initial pH of 8.2, COD was reduced by 50% due to oxidation and coagulation, a level almost equivalent to those obtained by Fenton treatment. Meanwhile, the 5-day biochemical oxygen demand (BOD(5))/COD ratio was increased from 0.02 to 0.17. In particular, the effect of initial pH became minor at H(2)O(2) addition rate greater than the theoretical demand for complete oxidation of organics by H(2)O(2). In addition, 83% of 300 mg/L ammonia nitrogen and 38% of 8.30 mS/cm electrical conductivity were removed when the initial pH was not adjusted. Based on these results, the process appears suitable for treatment of mature leachate.

Performance Study of Ceramic Filter Module in Recirculated Aquaculture System (RAS)

Science.gov (United States)

Ng, L. Y.; Ng, C. Y.

2017-06-01

The growth of world population has led to significant increase in seafood demand over the world. Aquaculture has been widely accepted by many countries to increase the seafood production owing to the decline of natural seafood resources. The aquaculture productivity, however, is directly linked to the pond water quality. In this study, attempts were made to employ ceramic micro-filter to improve the pond water quality through filtration processes. There were two batches of filtration processes, short term (1 hour) and long term (48 hours). Significant improvements on real pond water quality were recorded through the short term microfiltration process, which reduced turbidity (96%), total suspended solids (TSS) (80%), biochemical oxygen demand (BOD) (72%), chemical oxygen demand (COD) (55%), ammonia (60%), nitrate (96%) and phosphorus (83%). The long term filtration process also showed high efficiency in the removal of solid particle and organic matters. The results showed that all of the parameters were successfully reduced to acceptable ranges (turbidityfiltered pond water. Current study showed that the microfiltration using ceramic micro-filter has high potential to be used in recirculating aquaculture system throughout the aquaculture activities in order to maintain the pond water quality, thus, increase the survival rate of cultured species.

Function and Content of Maternal Demands: Developmental Significance of Early Demands for Competent Action.

Science.gov (United States)

Kuczynski, Leon; Kochanska, Grazyna

1995-01-01

Examined mothers' demands during mothers' interactions with their 1.5- to 3.5-year olds. Mothers with authoritative child-rearing attitudes emphasized proactive, competence-oriented demands and avoided regulatory control. Maternal demands for competent action predicted fewer behavior problems in their children at age five; maternal demands focused…

Application of constructed wetlands to the treatment of leachates from a municipal solid waste landfill in Ibadan, Nigeria.

Science.gov (United States)

Aluko, Olufemi Oludare; Sridhar, M K C

2005-06-01

Leachates are wastewater generated principally from landfills and solid waste disposal sites. Leachates emanating from municipal wastes are a major source of surface and groundwater pollution worldwide. Globally, leachates have been implicated in low yield of farm produce, developmental anomalies, low birth weights, leukemia incidence, and other cancers in communities around the site. They have also been implicated in hazards to the environment, loss of biodiversity, and contamination of water sources. At Aba-Eku in Nigeria, leachates are being discharged into the Omi Stream without treatment. A study was conducted on a method of leachate treatment that passes the leachate through constructed wetlands using Ipomoea aquatica (Forsk), a locally available plant found close to the landfill site. The aim of the study was to evolve a sustainable and cost-effective method of treatment whose effluents can be discharged into the Omi Stream with no or minimal impact. The study was descriptive and analytical in design. Samples were collected and analyzed with standard methods for pH, suspended solids (SS), biochemical oxygen demand (BOD), chemical oxygen demand (COD), ammonia, nitrate, and trace metals. Raw leachates were turbid and amber in color and contained suspended solids (197.5 mg/L), ammonia (610.9 mg/L), lead (1.64 mg/L), iron (198.10 mg/L), and manganese (23.20 mg/L). When the leachates were passed through the constructed wetland with eight hours' detention time, effluents showed significant reductions in suspended solids (81.01 percent), BOD (86.03 percent), and ammonia (97.77 percent). The study shows that a constructed wetland is a feasible tool for the treatment of leachates before their disposal into the environment in Nigeria and can help safeguard environmental quality.

Effect of dietary crude protein levels in a commercial range, on the nitrogen balance, ammonia emission and pollutant characteristics of slurry in fattening pigs.

Science.gov (United States)

Hernández, F; Martínez, S; López, C; Megías, M D; López, M; Madrid, J

2011-06-01

An experiment was conducted to investigate the effect of dietary levels of crude protein (CP), close to the range used commercially and to the European Commission recommended values, on the nitrogen (N) balance, ammonia (NH(3)) emission and pollutant characteristics of the slurry from growing and finishing pigs. Three feeding programmes with different CP levels were compared during the growing and the finishing periods of fattening. Diets were formulated to be isoenergetic and for the digestible lysine : metabolisable energy ratio to be similar in all the diets for each phase, but differed in CP concentration (160, 150 and 140 g CP/kg for the growing phase and 155, 145 and 135 g CP/kg for the finishing phase). Faeces and urine from barrows (eight replicates per diet) allocated in metabolism cages were collected separately for 5 days to calculate the N balance and for 2 days to measure NH(3) emission in a laboratory system for 240 h. Excreta were analysed for pH, volatile fatty acids (VFA), total N, electrical conductivity (EC), total solids (TS), volatile solids (VS), biochemical oxygen demand (BOD(5)), chemical oxygen demand (COD) and NH(4)-N reduction of dietary CP content led to a linear decrease of urinary (P 0.05) during the 240 h of study. However, in the growing phase, the NH(3)-N level in slurry was lower (P 0.05) on total VFA, EC, TS, VS, COD or BOD(5) contents of excreta. These parameters were higher (P commercial diets and close to the European Commission recommended values will decrease urinary and total N excretion in the slurry of growing-finishing pigs. The slurry from finishing pigs is more concentrated than that from growing pigs.

On-Demand Telemetry

Data.gov (United States)

National Aeronautics and Space Administration — AFRC has previously investigated the use of Network Based Telemetry. We will be building on that research to enable On-Demand Telemetry. On-Demand Telemetry is a way...

Money Demand in Latvia

OpenAIRE

Ivars Tillers

2004-01-01

The econometric analysis of the demand for broad money in Latvia suggests a stable relationship of money demand. The analysis of parameter exogeneity indicates that the equilibrium adjustment is driven solely by the changes in the amount of money. The demand for money in Latvia is characterised by relatively high income elasticity typical for the economy in a monetary expansion phase. Due to stability, close fit of the money demand function and rapid equilibrium adjustment, broad money aggreg...

Treatment of sludge containing nitro-aromatic compounds in reed-bed mesocosms – Water, BOD, carbon and nutrient removal

International Nuclear Information System (INIS)

Gustavsson, L.; Engwall, M.

2012-01-01

Highlights: ► It is necessary to improve existing and develop new sludge management techniques. ► One method is dewatering and biodegradation of compounds in constructed wetlands. ► The result showed high reduction of all tested parameters after treatment. ► Plants improve degradation and Phragmites australis is tolerant to xenobiotics. ► The amount of sludge could be reduced by 50–70%. - Abstract: Since the mid-1970s, Sweden has been depositing 1 million ton d.w sludge/year, produced at waste water treatment plants. Due to recent legislation this practice is no longer a viable method of waste management. It is necessary to improve existing and develop new sludge management techniques and one promising alternative is the dewatering and treatment of sludge in constructed wetlands. The aim of this study was to follow reduction of organic carbon, BOD and nutrients in an industrial sludge containing nitro-aromatic compounds passing through constructed small-scale wetlands, and to investigate any toxic effect such as growth inhibition of the common reed Phragmites australis. The result showed high reduction of all tested parameters in all the outgoing water samples, which shows that constructed wetlands are suitable for carbon and nutrient removal. The results also showed that P. australis is tolerant to xenobiotics and did not appear to be affected by the toxic compounds in the sludge. The sludge residual on the top of the beds contained low levels of organic carbon and is considered non-organic and could therefore be landfilled. Using this type of secondary treatment method, the amount of sludge could be reduced by 50–70%, mainly by dewatering and biodegradation of organic compounds.

Sustainability assessment of novel chemical processes at early stage: application to biobased processes

NARCIS (Netherlands)

Patel, A.D.; Meesters, K.; Uil, H. den; Jong, E. de; Blok, K.; Patel, M.K.

2012-01-01

Chemical conversions have been a cornerstone of industrial revolution and societal progress. Continuing this progress in a resource constrained world poses a critical challenge which demands the development of innovative chemical processes to meet our energy and material needs in a sustainable way.

Deriving local demand for stumpage from estimates of regional supply and demand.

Science.gov (United States)

Kent P. Connaughton; Gerard A. Majerus; David H. Jackson

1989-01-01

The local (Forest-level or local-area) demand for stumpage can be derived from estimates of regional supply and demand. The derivation of local demand is justified when the local timber economy is similar to the regional timber economy; a simple regression of local on nonlocal prices can be used as an empirical test of similarity between local and regional economies....

Fate of coliforms and pathogenic parasite in four full-scale sewage treatment systems in India.

Science.gov (United States)

Tyagi, Vinay Kumar; Sahoo, B K; Khursheed, Anwar; Kazmi, A A; Ahmad, Z; Chopra, A K

2011-10-01

The occurrence and removal of fecal indicators (total coliforms (TC), fecal coliforms (FC), fecal streptococci (FS)) and pathogens (helminthes eggs) were studied in various municipal wastewater treatment processes (UASB + FPU, ASP, EA, WSP). The reductions in TC and FC concentrations were usually between 2.0 and 2.5 log units in up-flow anaerobic sludge blanket reactor incorporated with final polishing unit (UASB + FPU). Almost similar reduction was observed in activated sludge process system (ASP) and waste stabilization ponds system (WSP), while it was log 3.0 in extended aeration system (EA). UASB + FPU and WSP systems were observed more efficient to reduce helminthes eggs at almost 100%, whereas only 97% removal was observed in case of ASP and EA system. In addition to monitoring of indicator organisms, turbidity, suspended solids (SS), and biochemical oxygen demand (BOD) were used as indirect measure of the potential presence of microorganisms. Interrelationship of BOD, SS, and turbidity with fecal indicator bacteria concentration in influent and effluent manifest that improvement of the microbiological quality of wastewater is strongly linked to the removal of BOD and SS.

Radiation decomposition of humic substances in landfill disposal leachate

International Nuclear Information System (INIS)

Sawai, Takeshi; Sawai, Teruko; Shimokawa, Toshinari

1979-01-01

The leachate generated from landfill contains humic substances such as humic acid and fluvic acid. It shows, in general, high chemical oxygen demand (COD) and biological oxygen demand (BOD), and colors in dark brown. When the leachate collected on the No. 15 landfill in Tokyo Bay was irradiated by γ-rays from a 60 Co source in bubbling air, the total organic carbon (TOC) decreased with increasing dose and the brown color was bleached. The effects of pH, flow rate, and dose rate on the decrease of TOC, the variations of UV spectrum, and the formation of carbon dioxide by the irradiation were examined. The decreasing rate of TOC increased with an increase of the flow rate up to -- 11/min and showed a maximum value in the region of pH 4 - 6. It was also dependent on the dose rate and increased with a decrease of the dose rate. The radiation chemical yield, G(-TOC), reached 162 at low dose rate of 1.3 x 10 4 rad/h. This result suggests that a radiation-induced chain reaction occurred. The amount of TOC decreased was almost equal to that of carbon dioxide formed. This result shows that the organic substances were decomposed by irradiation to carbon dioxide as a final product and it was ejected from the solution. (author)

An overview of municipal solid waste management and landfill leachate treatment: Malaysia and Asian perspectives.

Science.gov (United States)

Kamaruddin, Mohamad Anuar; Yusoff, Mohd Suffian; Rui, Lo Ming; Isa, Awatif Md; Zawawi, Mohd Hafiz; Alrozi, Rasyidah

2017-12-01

Currently, generation of solid waste per capita in Malaysia is about 1.1 kg/day. Over 26,500 t of solid waste is disposed almost solely through 166 operating landfills in the country every day. Despite the availability of other disposal methods, landfill is the most widely accepted and prevalent method for municipal solid waste (MSW) disposal in developing countries, including Malaysia. This is mainly ascribed to its inherent forte in terms cost saving and simpler operational mechanism. However, there is a downside. Environmental pollution caused by the landfill leachate has been one of the typical dilemmas of landfilling method. Leachate is the liquid produced when water percolates through solid waste and contains dissolved or suspended materials from various disposed materials and biodecomposition processes. It is often a high-strength wastewater with extreme pH, chemical oxygen demand (COD), biochemical oxygen demand (BOD), inorganic salts and toxicity. Its composition differs over the time and space within a particular landfill, influenced by a broad spectrum of factors, namely waste composition, landfilling practice (solid waste contouring and compacting), local climatic conditions, landfill's physico-chemical conditions, biogeochemistry and landfill age. This paper summarises an overview of landfill operation and leachate treatment availability reported in literature: a broad spectrum of landfill management opportunity, leachate parameter discussions and the way forward of landfill leachate treatment applicability.

Characterization (environmental Signature) and Function of the Main Instrumented (monitoring Water Quality Network in Real Time) Rivers Atoyac and Zahuapan in High Atoyac Basin; in Dry, Rain and Winter Season 2013-2014; Puebla-Tlaxcala Mexico

Science.gov (United States)

Tavera, E. M.; Rodriguez-Espinosa, P. F.; Morales-Garcia, S. S.; Muñoz-Sevilla, N. P.

2014-12-01

The Zahuapan and Atoyac rivers were characterized in the Upper Atoyac through the integration of physical and chemical parameters (environmental firm) determining the behavior and function of the basin as a tool for measuring and monitoring the quality and management of water resources of the water in one of the most polluted rivers in Mexico. For the determination of the environmental signature proceeded to characterize the water through 11 physicochemical parameters: temperature (T), potential hydrogen (pH), dissolved oxygen (DO), spectral absorption coefficient (SAC), the reduction of oxide potential (ORP), turbidity (Turb), conductivity (l), biochemical oxygen demand in 5 days (BOD5), chemical oxygen demand (COD), total suspended solids (TSS) and total dissolved solids (TDS ), which were evaluated in 49 sites in the dry season, 47 for the rainy season and 23 for the winter season in the basin and Atoyac Zahuapan Alto Atoyac, Puebla-Tlaxcala, Mexico river; finding a mathematical algorithm to assimilate and better represent the information obtained. The algorithm allows us to estimate correlation greater than 0.85. The results allow us to propose the algorithm used in the monitoring stations for purposes of processing information assimilated form.This measurement and monitoring of water quality supports the project, the monitoring network in real time and the actions to clean up Atoyac River, in the urban area of the city of Puebla.

Cognitive task demands, self-control demands and the mental well-being of office workers.

Science.gov (United States)

Bridger, Robert S; Brasher, Kate

2011-09-01

The cognitive task demands of office workers and the self-control demands of their work roles were measured in a sample of 196 employees in two different office layouts using a self-report questionnaire, which was circulated electronically. Multiple linear regression analysis revealed that both factors were associated with mental well-being, but not with physical well-being, while controlling for exposure to psychosocial stressors. The interaction between cognitive task demands and self-control demands had the strongest association with mental well-being, suggesting that the deleterious effect of one was greater when the other was present. An exploratory analysis revealed that the association was stronger for employees working in a large open-plan office than for those working in smaller offices with more privacy. Frustration of work goals was the cognitive task demand having the strongest negative impact on mental well-being. Methodological limitations and scale psychometrics (particularly the use of the NASA Task Load Index) are discussed. STATEMENT OF RELEVANCE: Modern office work has high mental demands and low physical demands and there is a need to design offices to prevent adverse psychological reactions. It is shown that cognitive task demands interact with self-control demands to degrade mental well-being. The association was stronger in an open-plan office.

Estimation of demand function on natural gas and study of demand analysis

Energy Technology Data Exchange (ETDEWEB)

Kim, Y.D. [Korea Energy Economics Institute, Euiwang (Korea, Republic of)

1998-04-01

Demand Function is estimated with several methods about the demand on natural gas, and analyzed per usage. Since the demand on natural gas, which has big share of heating use, has a close relationship with temperature, the inter-season trend of price and income elasticity is estimated considering temperature and economic formation. Per usage response of natural gas demand on the changes of price and income is also estimated. It was estimated that the response of gas demand on the changes of price and income occurs by the change of number of users in long term. In case of the response of unit consumption, only industrial use shows long-term response to price. Since gas price barely responds to the change of exchange rate, it seems to express the price-making mechanism that does not reflect timely the import condition such as exchange rate, etc. 16 refs., 12 figs., 13 tabs.

Characteristics and Biodegradability of Wastewater Organic Matter in Municipal Wastewater Treatment Plants Collecting Domestic Wastewater and Industrial Discharge

Directory of Open Access Journals (Sweden)

Yun-Young Choi

2017-06-01

Full Text Available Municipal wastewater treatment plants (WWTPs in Korea collect and treat not only domestic wastewater, but also discharge from industrial complexes. However, some industrial discharges contain a large amount of non-biodegradable organic matter, which cannot be treated properly in a conventional biological WWTP. This study aimed to investigate the characteristics and biodegradability of the wastewater organic matter contained in the industrial discharges and to examine the fate of the industrial discharges in a biological WWTP. In contrast to most previous studies targeting a specific group of organic compounds or traditional water quality indices, such as biological oxygen demand (BOD and chemical oxygen demand (COD, this study was purposed to quantify and characterize the biodegradable and nonbiodegradable fractions of the wastewater organic matter. Chemical oxygen demand (COD fractionation tests and fluorescence spectroscopy revealed that the industrial discharge from dyeing or pulp mill factories contained more non-biodegradable soluble organic matter than did the domestic wastewater. Statistical analysis on the WWTPs’ monitoring data indicated that the industrial discharge containing non-biodegradable soluble organic matter was not treated effectively in a biological WWTP, but was escaping from the system. Thus, industrial discharge that contained non-biodegradable soluble organic matter was a major factor in the decrease in biodegradability of the discharge, affecting the ultimate fate of wastewater organic matter in a biological WWTP. Further application of COD fractionation and fluorescence spectroscopy to wastewaters, with various industrial discharges, will help scientists and engineers to better design and operate a biological WWTP, by understanding the fate of wastewater organic matter.

Accuracy of different sensors for the estimation of pollutant concentrations (total suspended solids, total and dissolved chemical oxygen demand) in wastewater and stormwater.

Science.gov (United States)

Lepot, Mathieu; Aubin, Jean-Baptiste; Bertrand-Krajewski, Jean-Luc

2013-01-01

Many field investigations have used continuous sensors (turbidimeters and/or ultraviolet (UV)-visible spectrophotometers) to estimate with a short time step pollutant concentrations in sewer systems. Few, if any, publications compare the performance of various sensors for the same set of samples. Different surrogate sensors (turbidity sensors, UV-visible spectrophotometer, pH meter, conductivity meter and microwave sensor) were tested to link concentrations of total suspended solids (TSS), total and dissolved chemical oxygen demand (COD), and sensors' outputs. In the combined sewer at the inlet of a wastewater treatment plant, 94 samples were collected during dry weather, 44 samples were collected during wet weather, and 165 samples were collected under both dry and wet weather conditions. From these samples, triplicate standard laboratory analyses were performed and corresponding sensors outputs were recorded. Two outlier detection methods were developed, based, respectively, on the Mahalanobis and Euclidean distances. Several hundred regression models were tested, and the best ones (according to the root mean square error criterion) are presented in order of decreasing performance. No sensor appears as the best one for all three investigated pollutants.

An analytical approach to activating demand elasticity with a demand response mechanism

International Nuclear Information System (INIS)

Clastres, Cedric; Khalfallah, Haikel

2015-01-01

The aim of this work is to demonstrate analytically the conditions under which activating the elasticity of consumer demand could benefit social welfare. We have developed an analytical equilibrium model to quantify the effect of deploying demand response on social welfare and energy trade. The novelty of this research is that it demonstrates the existence of an optimal area for the price signal in which demand response enhances social welfare. This optimal area is negatively correlated to the degree of competitiveness of generation technologies and the market size of the system. In particular, it should be noted that the value of un-served energy or energy reduction which the producers could lose from such a demand response scheme would limit its effectiveness. This constraint is even greater if energy trade between countries is limited. Finally, we have demonstrated scope for more aggressive demand response, when only considering the impact in terms of consumer surplus. (authors)

Demanding Dynamics - Demand articulation of intermediary organisations in emerging pharmaceutical innovations

NARCIS (Netherlands)

Boon, W.P.C.

2008-01-01

User involvement in emerging technological fields is carried by so-called demand articulation processes. These demand articulation processes are interactive learning processes in which stakeholders try to address what they perceive as important characteristics of, and to unravel preferences for an

Oxygen enriched air using membrane for palm oil wastewater treatment

Directory of Open Access Journals (Sweden)

Ramlah Mohd Tajuddin

2002-11-01

Full Text Available A research aimed to explore new method of aeration using oxygen enriched air performance on BOD reduction of palm oil wastewater was conducted. The oxygen enriched air was obtained from an Oxygen Enriched System (OES developed using asymmetric polysulfone hollow fiber membrane with composition consisting of PSF: 22%, DMAc: 31.8%, THF: 31.8%, EtOH: 14.4%. Palm oil wastewater samples were taken from facultative pond effluent. These samples were tested for its initial biochemical oxygen demand (BOD, total suspended solids (TSS, pH, conductivity, turbidity, dissolved oxygen (DO, suspended solids (SS, and total dissolved solids (TDS before being subjected to two modes of aeration system, that is diffused air and oxygen enriched air. These water quality concentrations were tested for every 20 minutes for two-hour period during the aeration process. Results of BOD, TSS, pH, conductivity, DO, SS and TDS concentrations against time of samples from the two modes of aeration were then compared. It was found that DO concentration achieved in oxygen enriched air aeration was better than aeration using diffused air system. Aeration using OES improve the DO concentration in the wastewater and thus improve the BOD reduction and also influence other physical characteristics of wastewater. This phenomenon indicates the advantage of using air with higher oxygen concentration for wastewater aeration instead of diffused air system.

Ad libitum or demand/semi-demand feeding versus scheduled interval feeding for preterm infants.

Science.gov (United States)

McCormick, Felicia M; Tosh, Karen; McGuire, William

2010-02-17

Scheduled interval feeding of prescribed enteral volumes is current standard practice for preterm infants. However, feeding preterm infants in response to their hunger and satiation cues (ad libitum or demand/semi demand) rather than at scheduled intervals might help in the establishment of independent oral feeding, increase nutrient intake and growth rates, and allow earlier hospital discharge. To assess the effect of a policy of feeding preterm infants on an ad libitum or demand/semi-demand basis versus feeding prescribed volumes at scheduled intervals on growth rates and the time to hospital discharge. We used the standard search strategy of the Cochrane Neonatal Review Group. This included searches of the Cochrane Central Register of Controlled Trials (CENTRAL, The Cochrane Library, Issue 4, 2009), MEDLINE (1966 to Oct 2009), EMBASE (1980 to Oct 2009), CINAHL (1982 to Oct 2009), conference proceedings, and previous reviews. Randomised or quasi-randomised controlled trials (including cluster randomised trials) that compared a policy of feeding preterm infants on an ad libitum or demand/semi-demand basis versus feeding at scheduled intervals. We used the standard methods of the Cochrane Neonatal Review Group with separate evaluation of trial quality and data extraction by two review authors. We found eight randomised controlled trials that compared ad libitum or demand/semi-demand regimens with scheduled interval regimes in preterm infants in the transition phase from intragastric tube to oral feeding. The trials were generally small and of variable methodological quality. The duration of the intervention and the duration of data collection and follow-up in most of the trials was not likely to have allowed detection of measurable effects on growth. Three trials reported that feeding preterm infants using an ad libitum or demand/semi-demand feeding regimen allowed earlier discharge from hospital (by about two to four days) but other trials did not confirm this

Diffusion pollution from livestock and poultry rearing in the Yangtze Delta, China.

Science.gov (United States)

Gu, Pei; Shen, Ren Fang; Chen, Yi Ding

2008-05-01

The Yangtze Delta is one of the most developed regions in China and includes Shanghai, eight cities in Jiangsu province and eight cities in Zhejiang province. Meat consumption in this region has increased with economic growth, and most of the consumed meat is produced locally. The water quality of surface waters has deteriorated in recent years. An example was the huge blue-green algae bloom in Tai Lake in late May 2007, which affected millions of people's daily drinking water. However, animal husbandry is considered to be one of the main pollution sources. Pollutants (NH3-N, total phosphorus (TP), and total nitrogen (TN)) excreted by livestock and poultry, and the resultant COD (chemical oxygen demand) and BOD (biochemical oxygen demand), were estimated using two different methods based on different data sets. The number of livestock and poultry has remained stable in the Yangtze Delta over the four years from 1999 to 2002, with the average number of pigs, cattle, sheep and poultry being 21.1 M, 0.4 M, 7.7 M and 597.6 M, respectively. Pollutants in livestock and poultry excreta estimated by Method I were: 0.12 Mt NH3-N, 0.11 Mt TP and 0.29 Mt TN, resulting in COD and BOD of 1.34 Mt and 1.30 Mt, respectively, while the estimations based on Method II were: 0.18 Mt NH3-N, 0.15 Mt TP and 0.40 Mt TN, resulting in COD and BOD of 1.95 Mt and 1.80 Mt, respectively. Pollutants excreted annually by livestock and poultry in the Yangtze Delta are estimated to be: 0.17 Mt NH3-N, 0.16 Mt TP and 0.42 Mt TN, giving rise to a COD of 1.86 Mt and a BOD of 1.72 Mt. Approximately 25% of this pollution was estimated to enter water bodies, which means that the annual pollutant load is 43,700 t NH3-N, 39,400 tTP, 104,600t TN with a COD of 465,000 tand a BOD of 430,100 t. Pollutants from animal husbandry were similar in magnitude to those from industrial wastewater. Pigs produced the most pollution, followed by poultry, cattle and sheep. The pollution load from animal husbandry in the

Effect of organic nitrogen concentration on the efficiency of trickling filters

Science.gov (United States)

Kopeć, Łukasz; Drewnowski, Jakub; Fernandez-Morales, F. J.

2018-02-01

The study was conducted in Poland at six selected wastewater treatment plants (WWTP) based on the trickling filters Bioclere® technology. The aim of the study was to find the relationship between the influent organic nitrogen concentration and the purification efficiency expressed as effluent COD concentration. In the tests performed, the COD to BOD5 relationship was close to 2 and the ratio of BOD5 to TN was lower than 4. The research indicated that this specific chemical composition of raw wastewater causes appearance of filamentous bacteria on the surface of trickling filter filling and strongly affect the effluent quality.

Demand-Side Flexibility for Energy Transitions: Ensuring the Competitive Development of Demand Response Options

OpenAIRE

Nursimulu, Anjali; Florin, Marie-Valentine; Vuille, François

2015-01-01

This report provides an overview of the current debates about demand response development, focusing primarily on Europe, with some comparisons to the United States. ‘Demand response’ includes strategies that involve end-use customers adapting or altering their electricity demand in response to grid conditions or market prices. It is viewed as a multi-purpose power-system resource that enhances the energy system’s capacity to cope with increasing demand, rising costs of conventional transmissi...

Marine pollution in Cameroon (Gulf of Guinea): State and remedies for successful control and monitoring

International Nuclear Information System (INIS)

Folack, J.

1999-01-01

This paper analyses the various research results obtained over several years in Cameroon on coastal and marine pollution, especially pollution by solid wastes, industrial and domestic effluents, hydrocarbons (tar balls), heavy metals and pesticides. Values in the order of 175,531 and 194,685 tons have been estimated for annual pollution loads in terms of BOD and suspended matter respectively. With respect to BOD, the most polluting industries are petroleum refineries, food processing and chemical industries which respectively represent 38, 36 and 10% of the total annual BOD. Measurement of tar balls on various Cameroonian beaches shows values as high as 42.40 g/m 2 of beach, while the concentration of heavy metals encountered in shrimps and fish consumed in Cameroon shows a very wide range of values. Most of these values are similar to those obtained within the region, and some are alarming in their magnitude

Bio-based C-3 Platform Chemical: Biotechnological Production and -Conversion of 3-Hydroxypropionaldehyde

OpenAIRE

Rezaei, Roya

2013-01-01

Demands for efficient, greener, economical and sustainable production of chemicals, materials and energy have led to development of industrial biotechnology as a key technology area to provide such products from bio-based raw materials from agricultural-, forestry- and related industrial residues and by-products. For the bio-based industry, it is essential to develop a number of building blocks or platform chemicals for C2-C6 chemicals and even aromatic chemicals. 3-hydroxypropionaldehyde (3H...

On energy demand

International Nuclear Information System (INIS)

Haefele, W.

1977-01-01

Since the energy crisis, a number of energy plans have been proposed, and almost all of these envisage some kind of energy demand adaptations or conservation measures, hoping thus to escape the anticipated problems of energy supply. However, there seems to be no clear explanation of the basis on which our foreseeable future energy problems could be eased. And in fact, a first attempt at a more exact definition of energy demand and its interaction with other objectives, such as economic ones, shows that it is a highly complex concept which we still hardly understand. The article explains in some detail why it is so difficult to understand energy demand

Direct action of endocrine disrupting chemicals on human sperm

DEFF Research Database (Denmark)

Schiffer, Christian; Müller, Astrid; Egeberg, Dorte L

2014-01-01

Synthetic endocrine disrupting chemicals (EDCs), omnipresent in food, household, and personal care products, have been implicated in adverse trends in human reproduction, including infertility and increasing demand for assisted reproduction. Here, we study the action of 96 ubiquitous EDCs on huma...

Chemical tailoring of teicoplanin with site-selective reactions.

Science.gov (United States)

Pathak, Tejas P; Miller, Scott J

2013-06-05

Semisynthesis of natural product derivatives combines the power of fermentation with orthogonal chemical reactions. Yet, chemical modification of complex structures represents an unmet challenge, as poor selectivity often undermines efficiency. The complex antibiotic teicoplanin eradicates bacterial infections. However, as resistance emerges, the demand for improved analogues grows. We have discovered chemical reactions that achieve site-selective alteration of teicoplanin. Utilizing peptide-based additives that alter reaction selectivities, certain bromo-teicoplanins are accessible. These new compounds are also scaffolds for selective cross-coupling reactions, enabling further molecular diversification. These studies enable two-step access to glycopeptide analogues not available through either biosynthesis or rapid total chemical synthesis alone. The new compounds exhibit a spectrum of activities, revealing that selective chemical alteration of teicoplanin may lead to analogues with attenuated or enhanced antibacterial properties, in particular against vancomycin- and teicoplanin-resistant strains.

Physical-chemical and operational performance of an anaerobic baffled reactor (ABR treating swine wastewater = Desempenho físico-químico e operacional de um reator anaeróbio compartimentado (RAC como tratamento biológico preliminar de efluentes de suinocultura

Directory of Open Access Journals (Sweden)

Erlon Lopes Pereira

2010-10-01

Full Text Available Since hog raising concentrates a huge amount of swine manure in smallareas, it is considered by the environmental government organizations to be one of the most potentially pollutant activities. Therefore the main objective of this research was to evaluate by operational criteria and removal efficiency, the performance of a Anaerobic Baffled Reactor (ABR, working as a biological pre-treatment of swine culture effluents. The physical-chemical analyses carried out were: total COD, BOD5, total solids (TS, fix (TFS and volatiles (TVS, temperature, pH, total Kjeldahl nitrogen, phosphorus, total acidity and alkalinity. The ABR unit worked with an average efficiency of 65.2 and 76.2%, respectively, concerning total COD and BOD5, with a hydraulic retention time (HRT about 15 hours. The results for volumetric organic loading rate (VOLR, organic loading rate (OLR andhydraulic loading rate (HLR were: 4.46 kg BOD m-3 day-1; 1.81 kg BOD5 kg TVS-1 day-1 and 1.57 m3 m-3 day-1, respectively. The average efficiency of the whole treatment system for total COD and BOD5 removal were 66.5 and 77.8%, showing an adequate performancein removing the organic matter from swine wastewater.A suinocultura por ser uma atividade pecuária concentradora de dejetos em pequenas áreas é considerada, pelos órgãos de gerência ambiental, como uma das atividades mais degradadoras do meio ambiente. Nesta pesquisa objetivou-se, por conseguinte, avaliar a utilização de um reator anaeróbio compartimentado (RAC, como unidade de prétratamento de um reator tipo UASB, em escala piloto, na adequação ambiental dos efluentes de suinocultura, avaliando critérios operacionais e a eficiência. As análises físico-químicasrealizadas foram: DQOtotal, DBO5, sólidos totais (ST, fixos (SF e voláteis (SV, temperatura, pH, nitrogênio total Kjeldahl, fósforo, acidez total e alcalinidade. A unidade RAC trabalhou com eficiência de 65,2 e 76,2% para a remoção de DQOtotal e DBO5

Engineering aspects of ferrate in water and wastewater treatment - a review.

Science.gov (United States)

Yates, Brian J; Zboril, Radek; Sharma, Virender K

2014-01-01

There is renewed interest in the tetra-oxy compound of +6 oxidation states of iron, ferrate(VI) (Fe(VI)O4(2-)), commonly called ferrate. Ferrate has the potential in cleaner ("greener") technologies for water treatment and remediation processes, as it produces potentially less toxic byproducts than other treatment chemicals (e.g., chlorine). Ferrate has strong potential to oxidize a number of contaminants, including sulfur- and nitrogen-containing compounds, estrogens, and antibiotics. This oxidation capability of ferrate combines with its efficient disinfection and coagulation properties as a multi-purpose treatment chemical in a single dose. This review focuses on the engineering aspects of ferrate use at the pilot scale to remove contaminants in and enhance physical treatment of water and wastewater. In most of the pilot-scale studies, in-line and on-line electrochemical ferrate syntheses have been applied. In this ferrate synthesis, ferrate was directly prepared in solution from an iron anode, followed by direct addition to the contaminant stream. Some older studies applied ferrate as a solid. This review presents examples of removing a range of contaminants by adding ferrate solution to the stream. Results showed that ferrate alone and in combination with additional coagulants can reduce total suspended solids (TSS), chemical oxygen demand (COD), biological oxygen demand (BOD), and organic matter. Ferrate also oxidizes cyanide, sulfide, arsenic, phenols, anilines, and dyes and disinfects a variety of viruses and bacteria. Limitations and drawbacks of the application of ferrate in treating contaminated water on the pilot scale are also presented.

Olive mill wastewater evaporation management using PCA method Case study of natural degradation in stabilization ponds (Sfax, Tunisia).

Science.gov (United States)

Jarboui, Raja; Sellami, Fatma; Azri, Chafai; Gharsallah, Néji; Ammar, Emna

2010-04-15

Olive mill wastewater (OMW) evaporation ponds management was investigated in five serial evaporation open-air multiponds of 50 ha located in Sfax (Tunisia). Physico-chemical parameters and microbial flora evolution were considered. Empirical models describing the OMW characteristic changes with the operation time were established and Principal Component Analysis (PCA) described the correlation between physico-chemical and biological parameters. COD, BOD, total solids, polyphenols and electrical conductivity exhibited first-order models. Four groups exhibited high correlations. The first included temperature, density, COD, TSS, TS, BOD, VS, TOC, TKN, polyphenols and minerals. The second group was made up of yeasts and moulds. The third group was established with phenolic compounds, total sugars, fats, total phosphorous, NH(4)(+) and pH. The fourth group was constituted by exclusively aerobic bacteria. Bacterial-growth toxic effect was exhibited by high organic load, ash content and polyphenols, whereas moulds and yeasts were more adapted to OMW. During the storage, all the third group parameter values decreased and were inversely related to the others. In the last pond, COD, BOD, TS and TSS rates were reduced by 40%, 50%, 50% and 75% respectively. The evaporation and the biological activity were the main processes acting, predicting the OMW behavior during evaporation in air-open ponds. 2009 Elsevier B.V. All rights reserved.

Paper for Publication in IOP: Conference Series Leachate Treatment using three Years Aged Lysimetric Bioreactor Models

Science.gov (United States)

Hartono, Djoko M.; Andari Kristanto, Gabriel; Gusniani Sofian, Irma; Fauzan, Ahmad; Mahdiana, Ghanis

2018-03-01

reduction in the concentration of the parameters, even reaching 90% reduction for BOD (biological oxygen demand), COD, (chemical oxygen demand) nitrite, and TSS (total solid suspended) parameters. So it can be concluded that the recirculation of leachate of the sanitary landfill can reduce the concentration of pollutants in the leachate that will be discharged into water bodies, thereby reducing the pollution of the receiving water body. This research is funding by PUPT Kemristekdikti and DRPM UI

Chemical sensors and gas sensors for process control in biotechnology

International Nuclear Information System (INIS)

Williams, D.E.

1988-04-01

This paper is concerned with the possibilities for chemical measurement of the progress of biotechnological processes which are offered by devices already developed for other demanding applications. It considers the potential use of ultrasonic instrumentation originally developed for the nuclear industry, gas measurement methods from the fields of environmental monitoring and combustion control, nuclear instruments developed for the oil, mining and chemical industries, robotic systems and advanced control techniques. (author)

Ozonation of acid yellow 17 dye in a semi-batch bubble column

International Nuclear Information System (INIS)

Lackey, Laura W.; Mines, Richard O.; McCreanor, Philip T.

2006-01-01

A semi-batch bubble column was used to evaluate the effect of ozonation on the removal of acid yellow 17 dye from water. Results indicate that ozonation is very effective at removing acid yellow 17 dye from synthetic textile wastewater. The ozone consumed to apparent dye removal ratio ranged from 2 to 15,000 mg ozone per mg of dye decolorized and was dependent on both ozonation time and apparent dye concentration. The biodegradability of the dye wastewater was evaluated by monitoring changes in 5-day biochemical oxygen demand (BOD 5 ) with respect to chemical oxygen demand (COD). Results indicate that the wastewater biodegradability increased with an increase in ozonation time. Film theory was used to kinetically model the gas-liquid reactions occurring in the reactor. Modeling results indicated that during the first 10-15 min of ozonation, the system could be characterized by a fast, pseudo-first-order regime. With continued ozonation, system kinetics transitioned through a moderate then to a slow regime. Successful modeling of this period required use of a kinetic equation corresponding to a more inclusive condition. Model results are presented

Characterization of landfill leachates and studies on heavy metal removal.

Science.gov (United States)

Ceçen, F; Gürsoy, G

2000-10-01

This study covers a thorough characterisation of landfill leachates emerging from a sanitary landfill area. The landfill leachates were obtained in the acidic stage of landfill stabilisation. Their organic content was high as reflected by the high BOD5 (5 day biological oxygen demand) and COD (chemical oxygen demand) values. They were also highly polluted in terms of the parameters TKN (total Kjeldahl nitrogen), NH4-N, alkalinity, hardness and heavy metals. Nickel was present in these wastewaters at a significant concentration. With regard to the high heavy metal content of these wastewaters, several physicochemical removal alternatives for the heavy metals Cu, Pb, Zn, Ni, Cd, Cr, Mn and Fe were tested using coagulation, flocculation, precipitation, base addition and aeration. Additionally, COD removal and ammonia stripping were examined. Co-precipitation with either alum or iron salts did not usually lead to significantly higher heavy metal removal than lime alone. The major methods leading to an effective heavy metal removal were aeration and lime addition. Nickel and cadmium seemed to be strongly complexed and were not removed by any method. Also lead removal proved to be difficult. The results are also discussed in terms of compliance with standards.

Treatment of landfill leachate using an aerated, horizontal subsurface-flow constructed wetland.

Science.gov (United States)

Nivala, J; Hoos, M B; Cross, C; Wallace, S; Parkin, G

2007-07-15

A pilot-scale subsurface-flow constructed wetland was installed at the Jones County Municipal Landfill, near Anamosa, Iowa, in August 1999 to demonstrate the use of constructed wetlands as a viable low-cost treatment option for leachate generated at small landfills. The system was equipped with a patented wetland aeration process to aid in removal of organic matter and ammonia nitrogen. The high iron content of the leachate caused the aeration system to cease 2 years into operation. Upon the installation of a pretreatment chamber for iron removal and a new aeration system, treatment efficiencies dramatically improved. Seasonal performance with and without aeration is reported for 5-day biochemical oxygen demand (BOD(5)), chemical oxygen demand (COD), ammonia nitrogen (NH(4)-N), and nitrate nitrogen (NO(3)-N). Since winter air temperatures in Iowa can be very cold, a layer of mulch insulation was installed on top of the wetland bed to keep the system from freezing. When the insulation layer was properly maintained (either through sufficient litterfall or replenishing the mulch layer), the wetland sustained air temperatures of as low as -26 degrees C without freezing problems.

Multi-scale analysis of relationship between landscape pattern and urban river water quality in different seasons.

Science.gov (United States)

Xiao, Rui; Wang, Guofeng; Zhang, Qianwen; Zhang, Zhonghao

2016-05-05

Water quality is highly dependent on the landscape characteristics. In this study, we investigated the relationships between water quality and landscape pattern (composition and configuration) in Huzhou City, China. The water quality variables, including pH, dissolved oxygen (DO), chemical oxygen demand (CODMn), Biochemical Oxygen Demand (BOD), NH3-N, petroleum, dissolved total phosphorus (DTP), and total nitrogen (TN) in low water, normal water and flood periods were identified by investigating 34 sampling sites in Huzhou City during the period from 2001 to 2007. Landscape composition and landscape configuration metrics were calculated for different scales. It was found that scales and seasons both play important role when analyzing the relationships between landscape characteristics of different land use types. The results implied that some water quality parameters such as CODMn, petroleum are more polluted in flood period than the other two seasons at different scales, while DTP and TN are more polluted in low water period. Influences of different landscape metrics on water quality should operate at different spatial scales. The results shown in this paper will effectively provide scientific basis for the policy making in sustainable development of water environment.

Waste water purification using new porous ceramics prepared by recycling waste glass and bamboo charcoal

Science.gov (United States)

Nishida, Tetsuaki; Morimoto, Akane; Yamamoto, Yoshito; Kubuki, Shiro

2017-12-01

New porous ceramics (PC) prepared by recycling waste glass bottle of soft drinks (80 mass%) and bamboo charcoal (20 mass%) without any binder was applied to the waste water purification under aeration at 25 °C. Artificial waste water (15 L) containing 10 mL of milk was examined by combining 15 mL of activated sludge and 750 g of PC. Biochemical oxygen demand (BOD) showed a marked decrease from 178 to 4.0 (±0.1) mg L-1 in 5 days and to 2.0 (±0.1) mg L-1 in 7 days, which was equal to the Environmental Standard for the river water (class A) in Japan. Similarly, chemical oxygen demand (COD) decreased from 158 to 3.6 (±0.1) mg L-1 in 5 days and to 2.2 (±0.1) mg L-1 in 9 days, which was less than the Environmental Standard for the Seawater (class B) in Japan: 3.0 mg L-1. These results prove the high water purification ability of the PC, which will be effectively utilized for the purification of drinking water, fish preserve water, fish farm water, etc.

Use of shredded tire chips and tire crumbs as packing media in trickling filter systems for landfill leachate treatment.

Science.gov (United States)

Mondal, B; Warith, M A

2008-08-01

Scrap tire stockpiles are breeding grounds for pests, mosquitoes and west Nile viruses and, thereby, become a potential health risk. This experimental study was carried out in six stages to determine the suitability of shredded tire materials in a trickling filter system to treat landfill leachate. Biochemical oxygen demand (BOD5), chemical oxygen demand (COD) and NH3-N removals were obtained in the range of 81 to 96%, 76 to 90% and 15 to 68%, respectively. The removal of organics appears to be largely related to total dissolved solids reduction in leachate. A sudden increase, from time to time, in organic content of effluent could be attributed to biomass sloughing and clogging in the trickling filters. However, tire crumbs exhibited more consistent organics removal throughout the experimental program. Due to the high surface area of shredded tire chips and crumbs, a layer of biomass, 1-2 mm thick, was attached to them and was sloughed off at an interval of 21 days. Apart from that, as shredded tires are comparatively cheaper than any other usable packing material, tire chips and tire crumbs appeared to be quite promising as packing media in trickling filters for landfill leachate treatment.

Problems the chemical industry of Japan faces and future prospects

Energy Technology Data Exchange (ETDEWEB)

Ishida, Shin' ichi

1989-01-01

Industry proceeds for the fiscal 1988 are expected to increase remarkably as they did in the previous year with 4.9% increase in revenue and 18.8% increase in profit (ordinary profit) from the previous year. The conditions of material industry are especially favorable and chemical industry is also expected to prosper as it did in the previous year. Problems this prospering chemical industry is facing are introduced in this report. Firstly, it is necessary to improve productivity by adopting more information and promoting factory automation in order to strengthen competition. The future of chemical industry depends on the introduction of information. Secondly, as demands of users are becoming more diversified, and cycles of products shorter, shortening of development terms is essential. It is necessary, therefore, to predict the demands of users in advance and seek after custom products. Thirdly, selection of product bases is required; it might be necessary to consider producing some product items abroad. Moreover, it is desirable to increase investments in investigation and pursue creativity putting much stress on basic investigations. 2 figs., 11 tabs.

Unicorns in the world of chemical bonding models.

Science.gov (United States)

Frenking, Gernot; Krapp, Andreas

2007-01-15

The appearance and the significance of heuristically developed bonding models are compared with the phenomenon of unicorns in mythical saga. It is argued that classical bonding models played an essential role for the development of the chemical science providing the language which is spoken in the territory of chemistry. The advent and the further development of quantum chemistry demands some restrictions and boundary conditions for classical chemical bonding models, which will continue to be integral parts of chemistry. Copyright (c) 2006 Wiley Periodicals, Inc.

Introducing a demand-based electricity distribution tariff in the residential sector: Demand response and customer perception

International Nuclear Information System (INIS)

Bartusch, Cajsa; Wallin, Fredrik; Odlare, Monica; Vassileva, Iana; Wester, Lars

2011-01-01

Increased demand response is essential to fully exploit the Swedish power system, which in turn is an absolute prerequisite for meeting political goals related to energy efficiency and climate change. Demand response programs are, nonetheless, still exceptional in the residential sector of the Swedish electricity market, one contributory factor being lack of knowledge about the extent of the potential gains. In light of these circumstances, this empirical study set out with the intention of estimating the scope of households' response to, and assessing customers' perception of, a demand-based time-of-use electricity distribution tariff. The results show that households as a whole have a fairly high opinion of the demand-based tariff and act on its intrinsic price signals by decreasing peak demand in peak periods and shifting electricity use from peak to off-peak periods. - Highlights: → Households are sympathetic to demand-based tariffs, seeing as they relate to environmental issues. → Households adjust their electricity use to the price signals of demand-based tariffs. → Demand-based tariffs lead to a shift in electricity use from peak to off-peak hours. → Demand-based tariffs lead to a decrease in maximum demand in peak periods. → Magnitude of these effects increases over time.

Price elasticity matrix of demand in power system considering demand response programs

Science.gov (United States)

Qu, Xinyao; Hui, Hongxun; Yang, Shengchun; Li, Yaping; Ding, Yi

2018-02-01

The increasing renewable energy power generations have brought more intermittency and volatility to the electric power system. Demand-side resources can improve the consumption of renewable energy by demand response (DR), which becomes one of the important means to improve the reliability of power system. In price-based DR, the sensitivity analysis of customer’s power demand to the changing electricity prices is pivotal for setting reasonable prices and forecasting loads of power system. This paper studies the price elasticity matrix of demand (PEMD). An improved PEMD model is proposed based on elasticity effect weight, which can unify the rigid loads and flexible loads. Moreover, the structure of PEMD, which is decided by price policies and load types, and the calculation method of PEMD are also proposed. Several cases are studied to prove the effectiveness of this method.

Market architecture and power demand management

International Nuclear Information System (INIS)

Rious, Vincent; Roques, Fabien

2014-12-01

Demand response is a cornerstone problem in electricity markets considering climate change constraint. Most liberalized electricity markets have a poor track record at developing demand response. In Europe, different models are considered for demand response, from a development under a regulated regime to a development under competitive perspectives. In this paper, focusing on demand response for mid-size and small consumers, we investigate which types of market signals should be sent to demand response aggregators to see demand response emerge as a competitive activity. Using data from the French power system over eight years, we compare the possible market design options to allow demand response to develop. Our simulations demonstrate that with the current market rules, demand response is not a profitable activity in the French electricity industry. Introducing a capacity remuneration could bring additional revenues to demand response aggregators if the power system has no over-capacity

Students' Ideas about How and Why Chemical Reactions Happen: Mapping the Conceptual Landscape

Science.gov (United States)

Yan, Fan; Talanquer, Vicente

2015-01-01

Research in science education has revealed that many students struggle to understand chemical reactions. Improving teaching and learning about chemical processes demands that we develop a clearer understanding of student reasoning in this area and of how this reasoning evolves with training in the domain. Thus, we have carried out a qualitative…

Job demands-resources model

OpenAIRE

Bakker, Arnold; Demerouti, Eva

2013-01-01

markdownabstract* The question of what causes job stress and what motivates people has received a lot of research attention during the past five decades. In this paper, we discuss Job Demands-Resources (JD-R) theory, which represents an extension of the Job Demands-Resources model (Bakker & Demerouti, 2007; Demerouti, Bakker, Nachreiner, & Schaufeli, 2001) and is inspired by job design and job stress theories. JD-R theory explains how job demands and resources have unique and multiplicative e...

Energy supply and demand in California

Science.gov (United States)

Griffith, E. D.

1978-01-01

The author expresses his views on future energy demand on the west coast of the United States and how that energy demand translates into demand for major fuels. He identifies the major uncertainties in determining what future demands may be. The major supply options that are available to meet projected demands and the policy implications that flow from these options are discussed.

DemandStat

International Nuclear Information System (INIS)

2003-01-01

DemandStat is an accurate and up-to-date international statistics database dedicated to energy demand, with an unrivaled level of details for powerful market analysis. It provides detailed consumption statistics (30 sectors) on all energies, detailed 2003 data and historical annual data since 1970, frequent data revision and update (2 updates options), 150 data sources gathered and expertized, all data on a single database Consistent and homogeneous statistics, in line with all major data providers (IEA, Eurostat, ADB, OLADE, etc), no ruptures in time-series with easy request building and data analysis and reactive support from data experts. (A.L.B.)

Lurgi MegaMethanol technology. Delivering the building blocks for the future fuel and monomer demand

Energy Technology Data Exchange (ETDEWEB)

Wurzel, T. [Lurgi AG, Frankfurt/Main (Germany)

2006-07-01

The paper describes the central role of methanol within a changing environment with respect to feedstock availability as well as steadily growing demand in fuel and monomer demand. The current large-scale production facilities are described with respect to the technological challenges in order to ensure the availability of sufficient methanol for down-stream applications. Different down-stream applications are described which clearly confirm that methanol is the dominant C1-building block due to its chemical flexibility. It is concluded that by means of the implementation of two MTP (Methanol to Propylene) projects in China initiated the era of ''down-stream methanol'' has begun in the industry. (orig.)

Demonstration of an Environmentally Benign and Reduced Corrosion Runway Deicing Fluid

Science.gov (United States)

2011-01-01

43201 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY NAME(S) AND ADDRESS(ES) Enviromental Security Technology...Center for Engineering and the Environment AFCESA Air Force Civil Engineering Support Agency AFI Air Force Instruction AFMC Air Force Materiel Command...American Society for Testing and Materials BOD Biochemical Oxygen Demand CRREL Cold Regions Research and Engineering Laboratory CFR Code of

Sustainability of biofuels and renewable chemicals production from biomass.

Science.gov (United States)

Kircher, Manfred

2015-12-01

In the sectors of biofuel and renewable chemicals the big feedstock demand asks, first, to expand the spectrum of carbon sources beyond primary biomass, second, to establish circular processing chains and, third, to prioritize product sectors exclusively depending on carbon: chemicals and heavy-duty fuels. Large-volume production lines will reduce greenhouse gas (GHG) emission significantly but also low-volume chemicals are indispensable in building 'low-carbon' industries. The foreseeable feedstock change initiates innovation, securing societal wealth in the industrialized world and creating employment in regions producing biomass. When raising the investments in rerouting to sustainable biofuel and chemicals today competitiveness with fossil-based fuel and chemicals is a strong issue. Many countries adopted comprehensive bioeconomy strategies to tackle this challenge. These public actions are mostly biased to biofuel but should give well-balanced attention to renewable chemicals as well. Copyright © 2015 Elsevier Ltd. All rights reserved.

Combined photo-Fenton and biological treatment for Diuron and Linuron removal from water containing humic acid

International Nuclear Information System (INIS)

Farre, Maria Jose; Domenech, Xavier; Peral, Jose

2007-01-01

A combined chemical (photo-Fenton) and biological treatment has been proposed for Diuron and Linuron degradation in water containing natural dissolved organic matter (DOM). Humic acid (HA) was used to simulate the DOM. During the photo-Fenton process ([Fe(II)]=15.9mgL -1 , [H 2 O 2 ]=202mgL -1 , 60min of UVA irradiation time), the chemical oxygen demand (COD), total organic carbon (TOC), toxicity (EC 50 15 ) and biodegradability (BOD 5 /COD) of the generated intermediates were assessed. A reduction of photo-Fenton efficiency was observed when HA was present in solution. This effect has been explained as the result of a UVA light screening as well as a OH? radical quenching process by the HA. After the photo-Fenton process, the initial toxic and non-biodegradable herbicides were transformed into intermediates suitable for a subsequent aerobic biological treatment that was performed in a sequencing batch reactor (SBR). Complete elimination of the intermediates in presence of HA was reached at the end of the chemical-biological coupled system. Biosorption of HA onto the aerobic biomass was characterized. The results indicate that the Freundlich model adequately describes the adsorption of HA, a phenomena that follows a pseudo second-order adsorption kinetic model

Combined photo-Fenton and biological treatment for Diuron and Linuron removal from water containing humic acid

Energy Technology Data Exchange (ETDEWEB)

Farre, Maria Jose [Departament de Quimica, Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain); Domenech, Xavier [Departament de Quimica, Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain); Peral, Jose [Departament de Quimica, Universitat Autonoma de Barcelona, 08193 Bellaterra (Spain)]. E-mail: jose.peral@uab.es

2007-08-17

A combined chemical (photo-Fenton) and biological treatment has been proposed for Diuron and Linuron degradation in water containing natural dissolved organic matter (DOM). Humic acid (HA) was used to simulate the DOM. During the photo-Fenton process ([Fe(II)]=15.9mgL{sup -1}, [H{sub 2}O{sub 2}]=202mgL{sup -1}, 60min of UVA irradiation time), the chemical oxygen demand (COD), total organic carbon (TOC), toxicity (EC{sub 50}{sup 15}) and biodegradability (BOD{sub 5}/COD) of the generated intermediates were assessed. A reduction of photo-Fenton efficiency was observed when HA was present in solution. This effect has been explained as the result of a UVA light screening as well as a OH? radical quenching process by the HA. After the photo-Fenton process, the initial toxic and non-biodegradable herbicides were transformed into intermediates suitable for a subsequent aerobic biological treatment that was performed in a sequencing batch reactor (SBR). Complete elimination of the intermediates in presence of HA was reached at the end of the chemical-biological coupled system. Biosorption of HA onto the aerobic biomass was characterized. The results indicate that the Freundlich model adequately describes the adsorption of HA, a phenomena that follows a pseudo second-order adsorption kinetic model.

Demands Set Upon Modern Cartographic Visualization

Directory of Open Access Journals (Sweden)

Stanislav Frangeš

2007-05-01

Full Text Available Scientific cartography has the task to develop and research new methods of cartographic visualization. General demands are set upon modern cartographic visualization, which encompasses digital cartography and computer graphics: legibility, clearness, accuracy, plainness and aesthetics. In this paper, it is explained in detail what demands should be met in order to satisfy the general demands set. In order to satisfy the demand of legibility, one should respect conditions of minimal sizes, appropriate graphical density and better differentiation of known features. Demand of clearness needs to be met by fulfilling conditions of simplicity, contrasting quality and layer arrangement of cartographic representation. Accuracy, as the demand on cartographic visualization, can be divided into positioning accuracy and accuracy signs. For fulfilling the demand of plainness, the conditions of symbolism, traditionalism and hierarchic organization should be met. Demand of aesthetics will be met if the conditions of beauty and harmony are fulfilled.

Application of Solid Phase Microextraction Coupled with Gas Chromatography/Mass Spectrometry as a Rapid Method for Field Sampling and Analysis of Chemical Warfare Agents and Toxic Industrial Chemicals

National Research Council Canada - National Science Library

Hook, Gary L

2003-01-01

..., is: What chemicals are present? In order to answer this question rapidly, there is increasing demand for field analysis of volatile and semi-volatile organic compounds with instrumentation that provides definitive identification...

North American oil demand outlook

International Nuclear Information System (INIS)

Stewart, M.B.

1995-01-01

An understanding of the relationship of economic growth and potential petroleum product demand is needed to forecast the potential for North American oil demand growth as well as knowledge of world supply and price. The bullish expectations for economic growth in the US and Canada auger well for North American refiners and marketeers. The growth in world economic output forecast, however, means a larger oil demand and an increase in OPEC's pricing power. Such price increases could depress North American oil demand growth. (author)

Dynamic inventory rationing strategies for inventory systems with two demand classes, Poisson demand and backordering

NARCIS (Netherlands)

Teunter, Ruud H.; Haneveld, Willem K. Klein

2008-01-01

We study inventory systems with two demand classes (critical and non-critical), Poisson demand and backordering. We analyze dynamic rationing strategies where the number of items reserved for critical demand depends on the remaining time until the next order arrives. Different from results in the

Pay for load demand - electricity pricing with load demand component

International Nuclear Information System (INIS)

Pyrko, Jurek; Sernhed, Kerstin; Abaravicius, Juozas

2003-01-01

This publication is part of a project called Direct and Indirect Load Control in Buildings. Peak load problems have attracted considerable attention in Sweden during last three winters, caused by a significant decrease in available reserve power, which is a consequence of political decisions and liberalisation of the electricity market. A possible way to lower peak loads, avoiding electricity shortages and reducing electricity costs both for users and utilities, is to make customers experience the price difference during peak load periods and, in this way, become more aware of their energy consumption pattern and load demand. As of January 1st 2001, one of the Swedish energy utilities - Sollentuna Energi - operating in the Stockholm area, introduced a new electricity tariff with differentiated grid fees based on a mean value of the peak load every month. This tariff was introduced for all residential customers in the service area. The objective of this study is to investigate the extent to which a Load Demand Component, included in electricity pricing, can influence energy use and load demand in residential buildings. What are the benefits and disadvantages for customers and utilities? This paper investigates the impact of the new tariff on the utility and different types of typical residential customers, making comparisons with previous tariff. Keywords Load demand, electricity pricing, tariff, residential customers, energy behaviour

The Analysis of Septic Tank Performance in Regard to Suspended Solids and Organic Matter Removal

Directory of Open Access Journals (Sweden)

Ala Kirjanova

2011-12-01

Full Text Available Abstract 117 The aim of this work was to evaluate the removal of suspended solids (SS and 7-day biochemical oxygen demand (BOD7 in a three chamber septic tank depending on theoretical wastewater retention time and the degree of septic tank cleanliness. It was found out that the performance of the septic tank depended on the degree of its cleanliness: when the septic tank was clean and retention time was three days, SS and BOS7 removal efficiency was 77±10% and 67±14% respectively, whereas two months later, after septic tank desludging, SS removal efficiency decreased to 53±22% and BOD7 to 32±31%. The performance of the septic tank also depended on theoretical wastewater retention time: when some amount of solids was accumulated at the bottom of the septic tank and wastewater retention time was one day, SS and BOS7 removal efficiency was 45±40% and 33±16% respectively; when retention time was three days, SS removal efficiency increased to 53±22% but BOD7 removal efficiency remained similar to one day retention time, i.e. 32±31%.Article in Lithuanian

Application of water quality models to rivers in Johor

Science.gov (United States)

Chii, Puah Lih; Rahman, Haliza Abd.

2017-08-01

River pollution is one the most common hazard in many countries in the world, which includes Malaysia. Many rivers have been polluted because of the rapid growth in industrialization to support the country's growing population and economy. Domestic and industrial sewage, agricultural wastes have polluted the rivers and will affect the water quality. Based on the Malaysia Environment Quality Report 2007, the Department of Environment (DOE) has described that one of the major pollutants is Biochemical Oxygen Demand (BOD). Data from DOE in 2004, based on BOD, 18 river basins were classified polluted, 37 river basins were slightly polluted and 65 river basins were in clean condition. In this paper, two models are fitted the data of rivers in Johor state namely Streeter-Phelps model and nonlinear regression (NLR) model. The BOD concentration data for the two rivers in Johor state from year 1981 to year 1990 is analyzed. To estimate the parameters for the Streeter-Phelps model and NLR model, this study focuses on the weighted least squares and Gauss-Newton method respectively. Based on the value of Mean Square Error, NLR model is a better model compared to Streeter-Phelps model.

Chemical engineering and chemistry : education in a changing world

NARCIS (Netherlands)

Reijenga, J.C.

2006-01-01

Current trends in science and engineering research are analyzed, together with an inventory of changes in the field of employment and practice in industry. The resulting demands on university education of chemists and chemical engineers have been translated into a more or less continuous updating of

Energy supply and demand in Canada and export demand for Canadian energy, 1966--1990

Energy Technology Data Exchange (ETDEWEB)

1969-01-01

This report presents the results of a National Energy Board staff study of energy supply and demand in Canada to 1990. The study covers all forms of energy in Canada, and probable sources of supply for serving both indigenous and export demand for Canadian energy. Energy demand by market sector (residential and commercial, industrial, and transportation) is discussed in Chapters III, IV and V, respectively. Chapters VI, VII, VIII, and IX deal with supply prospects for Canadian petroleum, natural gas, coal, and electricity serving indigenous and export markets. A summary of the report is contained in Chapter II. Appendix A reviews general assumptions including those relating to population and household growth. Appendix B summarizes the methodology used for estimating residential energy demand, automobile transportation energy demand, and electricity supply. Appendix C includes a number of tables which provide detailed information. A list of definitions and abbreviations follows the Table of Contents.

Production of solar chemicals: gaining selectivity with hybrid molecule/semiconductor assemblies.

Science.gov (United States)

Hennessey, Seán; Farràs, Pau

2018-05-29

Research on the production of solar fuels and chemicals has rocketed over the past decade, with a wide variety of systems proposed to harvest solar energy and drive chemical reactions. In this Feature Article we have focused on hybrid molecule/semiconductor assemblies in both powder and supported materials, summarising recent systems and highlighting the enormous possibilities offered by such assemblies to carry out highly demanding chemical reactions with industrial impact. Of relevance is the higher selectivity obtained in visible light-driven organic transformations when using molecular catalysts compared to photocatalytic materials.

Sediment oxygen demand of wetlands in the oil sands region of north-eastern Alberta

International Nuclear Information System (INIS)

Slama, C.; Ciborowski, J.J.; Gardner Costa, J.

2009-01-01

Reclaimed land in the Alberta oil sands mining area contains both reference and oil sands process-affected wetlands constructed using varying sediment compositions. The sediments derived from oil sands process materials (OSPM) may alter the biochemical reactions that take place and affect the sediment oxygen demand (SOD), which is a key factor that contributes to oxygen depletion. This presentation reported on a study in which SOD was measured in a suite of constructed wetlands of different ages, with or without OSPM and topsoil. The purpose of the study was to clarify the role of SOD in wetland function and in the reclamation process. Dissolved oxygen loggers were inserted into dome-shaped chambers on the sediment to measure changes in oxygen demand. Complementary measurements of respiration (CO 2 elution) were used to quantify the biological sediment oxygen demand (BSOD) component of SOD. The chemical sediment oxygen demand (CSOD) was then determined by subtraction from SOD. Wetlands reclaimed using OSPM are expected to have a lower BSOD to CSOD ratio than reference wetlands. Residual ammonia in OSPM sediments may react with sulphate and bind phosphorus. This reduces phosphorus bioavailability and may impede submergent macrophyte growth. As such, wetlands affected by CSOD will have fewer submerged macrophytes than BSOD dominant wetlands.

Uranium supply and demand

International Nuclear Information System (INIS)

1984-05-01

This report covers the period 1983 to 1995. It draws together the industry's latest views on future trends in supply and demand, and sets them in their historical context. It devotes less discussion than its predecessors to the technical influences underpinning the Institute's supply and demand forecasts, and more to the factors which influence the market behaviour of the industry's various participants. As the last decade has clearly shown, these latter influences can easily be overlooked when undue attention is given to physical imbalances between supply and demand. (author)

Survey of Models on Demand, Customer Base-Line and Demand Response and Their Relationships in the Power Market

OpenAIRE

Heshmati, Almas

2012-01-01

The increasing use of demand-side management as a tool to reliably meet electricity demand at peak time has stimulated interest among researchers, consumers and producer organizations, managers, regulators and policymakers, This research reviews the growing literature on models used to study demand, consumer baseline (CBL) and demand response in the electricity market. After characterizing the general demand models, it reviews consumer baseline based on which further study the demand response...

Contribution of domestic wastewater to the total pollutant loading influent to a municipal wastewater treatment plant; Contribuciond e las aguas residuales domesticas a la carga total que accede a una EDAr municipal

Energy Technology Data Exchange (ETDEWEB)

Marin Galvin, R.; Perez de Siles, L. A.; Rojas Moreno, F. J.; Gonzalez Jimenez, M. M.

2004-07-01

A study on the purely domestic wastewater from Cordoba city (Abril to july 2003) has found a pollutant loading very high on these domestic wastewaters, by showing mean values of suspended solid, BOD{sub 5} and COD equal to respectively 452 mg/l, 505 mg/1 and 793 mg/l. This pollutants power probably emanates from the products for domestic cleaning used in our homes and must be associated to chemicals as citrates, oxalates, surfactants, polialcohols, organics complexing, ammonium compounds..., which show high value of pollutant loading up to 200 mg/l of BOD{sub 5} per ml of product have been measured on a commercial domestic dishwasher, and 9.000 mg/l of DQO for a domestic smoothing. Furthermore, the increasing use of pre-cooked foods can add to domestic wastewater fats, oils, and flours which can also increase the BOD:5 and COD values of these effluents. On the other hand, the measured pollutant loading or domestic wastewater from monofamily homes has been lower than those from multifamily buildings. Finally, due to the fact that the Golondrina's WWTP (Cordoba, 1991) was designed for treat values of suspended solids, BOD, and COD lower than those actually detected, its treatment processes should be probably modified in a near future. (Author) 24 refs.

Food safety information and food demand

DEFF Research Database (Denmark)

Smed, Sinne; Jensen, Jørgen Dejgård

2005-01-01

Purpose – The purpose of this paper is to analyze how news about food-related health risks affects consumers’ demands for safe food products. Design/methodology/approach – By identifying structural breaks in an econometrically estimated demand model, news with permanent impact on demand...... induces a permanent increase in the demand for pasteurized eggs, while more moderate negative news influences demand temporarily and to a lesser extent. There is, however, considerable variation in the response to food safety news across socio-demographic groups of consumers. Research limitations...... is distinguished from news with temporary impact. The Danish demand for pasteurized versus shell eggs is used as an illustrative case. Findings – Negative safety news about one product variety can provide significant stimulation to the demand for safe varieties. Severe negative news about the safety of shell eggs...

Evaluation of a treatment system wastewater prebeneficiado of coffee (Coffea arabica implemented in the community Carmen Pampa province of Nor Yungas of La Paz Department

Directory of Open Access Journals (Sweden)

Álvarez Javier

2011-08-01

Full Text Available This research was conducted in prebeneficiadora coffee plant of UAC-CP, located in the community of Carmen Pampa, Coroico Municipality, Nor Yungas of La Paz department. The objective was to determine the efficiency of wastewater treatment prebeneficiado coffee because it is not known to be effective in reducing the level of contamination of treated wastewater, and according to the results to correct and / or validate directly model system in place. For their study was established seven sampling points within the system of treatment and four replications were made at different times and with different amounts of coffee cherry. We evaluated the parameters of temperature, pH, settleable solids, total suspended solids, fixed and volatile, biochemical oxygen demand, chemical oxygen demand and dissolved oxygen. The temperature of wastewater entering the system has recorded 16.5 o C, increasing during the treatment process at 17.5 °C and record the output is 16.5 ºC. The pH increased from 4.51 to 6.04 which occurred at the last two gaps oxygenation and not in the neutralization tank. Settleable solids (SS increased from 0.1 mg / L to 0.15 mg / L, which was recorded at the lakes of oxygen, is attributed to the drag of fine gravel. Total suspended solids (TSS have been reduced from 1927.5 mg / L to 299 mg / L gradually throughout the treatment process. Fixed suspended solids (SSF were reduced from 137.5 mg / L to 58.5 mg / L. Volatile suspended solids (VSS were reduced from 1790 mg / L to 240.5 mg / L. Biochemical oxygen demand (BOD was reduced from 6102.5 mg O2 / L to 1245 mg O2 / L. The chemical oxygen demand (COD was reduced from 9800 mg O2 / L to 1658.75 mg O2 / L. Dissolved oxygen (DO increased from 0 to 2.4 mg O2 / L, in the last two gaps in oxygenation, due to the reduction of solids and chemical oxygen demand and biochemical oxygen. Of the nine parameters measured, six meet the maximum permissible values for download in source receptor (stream

A demanding market

International Nuclear Information System (INIS)

Thomas, M.

1997-01-01

The article relates to the oil and natural gas market, and it gives a survey of proved reserves at the end of 1996 worldwide. The long term trend of increasing world energy demand has seen a major rise during 1996 when global consumption grew by 3%. But worldwide demand, excluding the Former Soviet Union, shows this figure increasing further to 3.7% for the whole of last year according to statistics. 3 figs

Sizewell: UK power demand

International Nuclear Information System (INIS)

Anon.

1986-01-01

The Sizewell Inquiry was about whether the next power stations to be built in the UK should be nuclear or coal and, if nuclear, PWRs or AGRs. During the period of the Inquiry forecasts of demand for electricity were low. Now, however, it seems that the forecast demand is much increased. This uncertainty in demand and the wide regional variations are examined in some detail. Facts and figures on electricity sales (area by area) are presented. Also the minutes of supply lost per consumer per year. These show that security of supply is also a problem. It is also shown that the way electricity is used has changed. Whilst electricity generation has been changing to large-scale, centralised power stations the demand patterns may make smaller scale, quickly-constructed units more sensible. The questions considered at the Sizewell Inquiry may, indeed, no longer be the right ones. (UK)

46 CFR 169.689 - Demand loads.

Science.gov (United States)

2010-10-01

... 46 Shipping 7 2010-10-01 2010-10-01 false Demand loads. 169.689 Section 169.689 Shipping COAST... Electrical Electrical Installations on Vessels of 100 Gross Tons and Over § 169.689 Demand loads. Demand loads must meet § 111.60-7 of this chapter except that smaller demand loads for motor feeders are...

Stochastic model of forecasting spare parts demand

OpenAIRE

Ivan S. Milojević; Rade V. Guberinić

2012-01-01

If demand is known for the whole planning period (complete information), then this type of demand or a supply system is deterministic. In the simplest cases, the demand per time unit is constant. If demand levels change over time following a precisely determined and pre-known principle, this type of demand is also classified as deterministic. This quality of demand is very rare. In most cases demand is the product of a process, for example TMS maintenance, whose progression cannot be predicte...

Crucial market demands and company competencies

DEFF Research Database (Denmark)

Jensen, Bjarne; Stacey, Julia

1999-01-01

More and more, it is acknowledged that a company's success depends on it being capable of complying with the market's demands and wishes. It is, however, not always obvious, how the individual company will be able to meet the market's demands. A recent MAPP study has investigated this topic...... and identified a number of central market demands, which Danish food companies are faced with. Moreover, the study has identified which competencies are required to meet these demands and have also looked at howsuccessful companies structure some of these competencies. The study takes its point of departure...... in a literature review of MAPP's research. Results show that there are 27 central market demands, retail and consumer demands that Danish companies ought to be able to live up to. The study has also identified which competencies food companies must possess to be able to meet market's demands. Results from three...

A Novel Methylotrophic Bacterial Consortium for Treatment of Industrial Effluents.

Science.gov (United States)

Hingurao, Krushi; Nerurkar, Anuradha

2018-01-01

Considering the importance of methylotrophs in industrial wastewater treatment, focus of the present study was on utilization of a methylotrophic bacterial consortium as a microbial seed for biotreatment of a variety of industrial effluents. For this purpose, a mixed bacterial methylotrophic AC (Ankleshwar CETP) consortium comprising of Bordetella petrii AC1, Bacillus licheniformis AC4, Salmonella subterranea AC5, and Pseudomonas stutzeri AC8 was used. The AC consortium showed efficient biotreatment of four industrial effluents procured from fertilizer, chemical and pesticide industries, and common effluent treatment plant by lowering their chemical oxygen demand (COD) of 950-2000 mg/l to below detection limit in 60-96 h in 6-l batch reactor and 9-15 days in 6-l continuous reactor. The operating variables of wastewater treatment, viz. COD, BOD, pH, MLSS, MLVSS, SVI, and F/M ratio of these effluents, were also maintained in the permissible range in both batch and continuous reactors. Therefore, formation of the AC consortium has led to the development of an efficient microbial seed capable of treating a variety of industrial effluents containing pollutants generated from their respective industries.

Pollution source localization in an urban water supply network based on dynamic water demand.

Science.gov (United States)

Yan, Xuesong; Zhu, Zhixin; Li, Tian

2017-10-27

Urban water supply networks are susceptible to intentional, accidental chemical, and biological pollution, which pose a threat to the health of consumers. In recent years, drinking-water pollution incidents have occurred frequently, seriously endangering social stability and security. The real-time monitoring for water quality can be effectively implemented by placing sensors in the water supply network. However, locating the source of pollution through the data detection obtained by water quality sensors is a challenging problem. The difficulty lies in the limited number of sensors, large number of water supply network nodes, and dynamic user demand for water, which leads the pollution source localization problem to an uncertainty, large-scale, and dynamic optimization problem. In this paper, we mainly study the dynamics of the pollution source localization problem. Previous studies of pollution source localization assume that hydraulic inputs (e.g., water demand of consumers) are known. However, because of the inherent variability of urban water demand, the problem is essentially a fluctuating dynamic problem of consumer's water demand. In this paper, the water demand is considered to be stochastic in nature and can be described using Gaussian model or autoregressive model. On this basis, an optimization algorithm is proposed based on these two dynamic water demand change models to locate the pollution source. The objective of the proposed algorithm is to find the locations and concentrations of pollution sources that meet the minimum between the analogue and detection values of the sensor. Simulation experiments were conducted using two different sizes of urban water supply network data, and the experimental results were compared with those of the standard genetic algorithm.

Job demands-resources model

NARCIS (Netherlands)

A.B. Bakker (Arnold); E. Demerouti (Eva)

2013-01-01

markdownabstract* The question of what causes job stress and what motivates people has received a lot of research attention during the past five decades. In this paper, we discuss Job Demands-Resources (JD-R) theory, which represents an extension of the Job Demands-Resources model (Bakker &

Demand forecast model based on CRM

Science.gov (United States)

Cai, Yuancui; Chen, Lichao

2006-11-01

With interiorizing day by day management thought that regarding customer as the centre, forecasting customer demand becomes more and more important. In the demand forecast of customer relationship management, the traditional forecast methods have very great limitation because much uncertainty of the demand, these all require new modeling to meet the demands of development. In this paper, the notion is that forecasting the demand according to characteristics of the potential customer, then modeling by it. The model first depicts customer adopting uniform multiple indexes. Secondly, the model acquires characteristic customers on the basis of data warehouse and the technology of data mining. The last, there get the most similar characteristic customer by their comparing and forecast the demands of new customer by the most similar characteristic customer.

Future butanes supply/demand

International Nuclear Information System (INIS)

Whitley, S.C.

1992-01-01

This paper graphically depicts, through in-depth supply/demand analysis, how environmental regulations can be both bad and good for an industry. In the case of n-butane, the Environmental Protection Agency (EPA) summertime gasoline volatility regulations are a culprit - threatening to ultimately destroy refinery demand for the product as a gasoline blendstock. Waiting in the wings are environmental regulations that should eventually prove to be n-butane's savior. The regulations referred to here are the Clean Air Act (CAA) of 1990's mandate for motor fuel oxygenates. The negative impact of gasoline volatility regulations on U.S. n-butane demand and the positive impact that should come from the use of n-butane as a MTBE precursor are covered. Many variables exist which make studying the effects of these environmental regulations very difficult. Over the past three years RPC Group has conducted numerous studies on n-butane supply/demand, as impacted by both EPA gasoline volatility and fuel oxygenate regulations

Coupling of anodic oxidation and adsorption by granular activated carbon for chemical oxygen demand removal from 4,4'-diaminostilbene-2,2'-disulfonic acid wastewater.

Science.gov (United States)

Wang, Lizhang; Zhao, Yuemin

2010-01-01

Experiments were performed to reduce chemical oxygen demand (COD) from 4,4'-diaminostilbene-2,2'-disulfonic (DSD) acid manufacturing wastewater using electrochemical oxidation coupled with adsorption by granular activated carbon. The COD removal is affected by the residence time and applied voltage. When the residence time is increased, lower value of COD effluent could be obtained, however, the average current efficiency (ACE) decreased rapidly, and so does the applied voltage. In addition, aeration could effectively enhance COD removal efficiency and protect anodes from corrosion. Furthermore, the acidic condition is beneficial to the rapid decrease of COD and the values of pH effluent are independent of the initial solution pH. The optimization conditions obtained from these experiments are applied voltage of 4.8 V, residence time of 180 min and air-liquid ratio of 4.2 with the COD effluent of about 690 mg L⁻¹. In these cases, the ACE and energy consumption are 388% and 4.144 kW h kg⁻¹ COD, respectively. These perfect results from the experiments illustrate that the combined process is a considerable alternative for the treatment of industrial wastewater containing high concentration of organic pollutants and salinity.

Chemical sensors and microsystems for pollution abatement. Brief study

International Nuclear Information System (INIS)

Drost, S.; Aberl, F.; Endres, H.E.

1994-01-01

The demand for chemical sensors and microsystems is assessed on the basis of the substances which the pollution regulations identify as air and water pollutants in accordance with defined immission standards. Microsystems technology can do away with the disadvantages of environmental analysis. Chemical sensors offer many advantages but must be improved as regards their measuring accuracy and service life. These sensors must be developed further (transducers and coatings) and be combined into multisensor systems. Special sensor signal processing methods (pattern recognition) must be developed for the latter as microsystems technology advances. (orig./EF) [de

Water demand management in Mediterranean regions

OpenAIRE

Giulio Querini; Salvo Creaco

2005-01-01

Water sustainability needs a balance between demand and availability: 1) Water demand management: demand may be managed by suppliers and regulations responsible persons, using measures like invoicing, consumptions measurement and users education in water conservation measures; 2) Augmentation of water supply: availibility may be augmented by infrastructural measures, waste water reuse, non-conventional resources and losses reduction. Water Demand Management is about achieving a reduction in t...

Ethanol demand in Brazil: Regional approach

International Nuclear Information System (INIS)

Freitas, Luciano Charlita de; Kaneko, Shinji

2011-01-01

Successive studies attempting to clarify national aspects of ethanol demand have assisted policy makers and producers in defining strategies, but little information is available on the dynamic of regional ethanol markets. This study aims to analyze the characteristics of ethanol demand at the regional level taking into account the peculiarities of the developed center-south and the developing north-northeast regions. Regional ethanol demand is evaluated based on a set of market variables that include ethanol price, consumer's income, vehicle stock and prices of substitute fuels; i.e., gasoline and natural gas. A panel cointegration analysis with monthly observations from January 2003 to April 2010 is employed to estimate the long-run demand elasticity. The results reveal that the demand for ethanol in Brazil differs between regions. While in the center-south region the price elasticity for both ethanol and alternative fuels is high, consumption in the north-northeast is more sensitive to changes in the stock of the ethanol-powered fleet and income. These, among other evidences, suggest that the pattern of ethanol demand in the center-south region most closely resembles that in developed nations, while the pattern of demand in the north-northeast most closely resembles that in developing nations. - Research highlights: → Article consists of a first insight on regional demand for ethanol in Brazil. → It proposes a model with multiple fuels, i.e., hydrous ethanol, gasohol and natural gas. → Results evidence that figures for regional demand for ethanol differ amongst regions and with values reported for national demand. → Elasticities for the center-south keep similarities to patterns for fuel demand in developed nations while coefficients for the north-northeast are aligned to patterns on developing countries.

Drivers of U.S. mineral demand

Science.gov (United States)

Sznopek, John L.

2006-01-01

Introduction: The word 'demand' has different meanings for different people. To some, it means their 'wants and needs,' to others it is what they consume. Yet, when considering economics, demand refers to the specific amounts of goods or services that individuals will purchase at various prices. Demand is measured over a given time period. It is determined by a number of factors including income, tastes, and the price of complementary and substitute goods. In this paper, the term consumption is used fairly synonymously with the term demand. Most mineral commodities, like iron ore, copper, zinc, and gravel, are intermediate goods, which means that they are used in the production of other goods, called final goods. Demand for intermediate goods is called derived demand because such demand is derived from the demand for final goods. When demand increases for a commodity, generally the price rises. With everything else held constant, this increases the profits for those who provide this commodity. Normally, this would increase profits of existing producers and attract new producers to the market. When demand for a commodity decreases, generally the price falls. Normally, this would cause profits to fall and, as a consequence, the least efficient firms may be forced from the industry. Demand changes for specific materials as final goods or production techniques are reengineered while maintaining or improving product performance, for example, the use of aluminum in the place of copper in long distance electrical transmission lines or plastic replacing steel in automobile bumpers. Substitution contributes to efficient material usage by utilizing cheaper or technically superior materials. In this way, it may also alleviate materials scarcity. If a material becomes relatively scarce (and thus more expensive), a more abundant (and less expensive) material generally replaces it (Wagner and others, 2003, p. 91).

Ethanol demand in Brazil: Regional approach

Energy Technology Data Exchange (ETDEWEB)

Freitas, Luciano Charlita de, E-mail: lucianofreitas@hiroshima-u.ac.j [Graduate School for International Development and Cooperation, Development Policy, Hiroshima University 1-5-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8529 (Japan); Kaneko, Shinji [Graduate School for International Development and Cooperation, Development Policy, Hiroshima University 1-5-1 Kagamiyama, Higashi-Hiroshima, Hiroshima 739-8529 (Japan)

2011-05-15

Successive studies attempting to clarify national aspects of ethanol demand have assisted policy makers and producers in defining strategies, but little information is available on the dynamic of regional ethanol markets. This study aims to analyze the characteristics of ethanol demand at the regional level taking into account the peculiarities of the developed center-south and the developing north-northeast regions. Regional ethanol demand is evaluated based on a set of market variables that include ethanol price, consumer's income, vehicle stock and prices of substitute fuels; i.e., gasoline and natural gas. A panel cointegration analysis with monthly observations from January 2003 to April 2010 is employed to estimate the long-run demand elasticity. The results reveal that the demand for ethanol in Brazil differs between regions. While in the center-south region the price elasticity for both ethanol and alternative fuels is high, consumption in the north-northeast is more sensitive to changes in the stock of the ethanol-powered fleet and income. These, among other evidences, suggest that the pattern of ethanol demand in the center-south region most closely resembles that in developed nations, while the pattern of demand in the north-northeast most closely resembles that in developing nations. - Research highlights: {yields} Article consists of a first insight on regional demand for ethanol in Brazil. {yields} It proposes a model with multiple fuels, i.e., hydrous ethanol, gasohol and natural gas. {yields} Results evidence that figures for regional demand for ethanol differ amongst regions and with values reported for national demand. {yields} Elasticities for the center-south keep similarities to patterns for fuel demand in developed nations while coefficients for the north-northeast are aligned to patterns on developing countries.

Assessment Of Physico-Chemical Property Of Water Samples From Port Harcourt Bonny And Opobo Coastal Areas For Sustainable Coastal Tourism Development In Rivers State Nigeria.

Directory of Open Access Journals (Sweden)

Obinwanne

2015-08-01

Full Text Available Abstract The study evaluated some physico-chemical properties of water samples from Port Harcourt Bonny and Opobo to determine the safety of water from the areas for sustainable coastal tourism development in Rivers State Nigeria. Three water samples were collected with three sterilized plastic containers with a capacity of 25cl which were subjected to laboratory tests to know their constituents. The parameters tested were appearance temperature colour turbidity conductivity PH alkalinity lead Pb Chromium Cr Cadmium Cd Ammonia BODs and Dissolved Oxygen. The results of the water samples were compared with World Health Organization WHO water quality standard and the Nigeria National Water Quality standard to determine the safety of the water for human consumption and tourism development. The study revealed that Port Harcourt site has more prospects for tourism development more than Opobo study site because the Ph alkalinity and BODs levels were lower than that of Opobo making the water safer except that the amount of dissolved oxygen was a little high in Opobo and turbidity was not detected in Opobo. The study revealed that Bonny water was very dense in appearance dark brown in colour highly turbid basic and with mean concentration of the heavy metals Lead chromium and cadmium higher than the recommended World Health Organization WHO water quality standard and the Nigeria National Water Quality standard and therefore not safe for drinking and swimming. Treated portable water should be provided for the people of Port Harcourt Opobo and Bonny especially people from Bonny area and development of tourism in the state to save the people and tourists from imminent danger of fecal contaminants and toxic substances.

Addressing Energy Demand through Demand Response. International Experiences and Practices

Energy Technology Data Exchange (ETDEWEB)

Shen, Bo [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ghatikar, Girish [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ni, Chun Chun [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Dudley, Junqiao [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Martin, Phil [Enernoc, Inc., Boston, MA (United States); Wikler, Greg

2012-06-01

Demand response (DR) is a load management tool which provides a cost-effective alternative to traditional supply-side solutions to address the growing demand during times of peak electrical load. According to the US Department of Energy (DOE), demand response reflects “changes in electric usage by end-use customers from their normal consumption patterns in response to changes in the price of electricity over time, or to incentive payments designed to induce lower electricity use at times of high wholesale market prices or when system reliability is jeopardized.” 1 The California Energy Commission (CEC) defines DR as “a reduction in customers’ electricity consumption over a given time interval relative to what would otherwise occur in response to a price signal, other financial incentives, or a reliability signal.” 2 This latter definition is perhaps most reflective of how DR is understood and implemented today in countries such as the US, Canada, and Australia where DR is primarily a dispatchable resource responding to signals from utilities, grid operators, and/or load aggregators (or DR providers).

Evaluation of two pilot scale membrane bioreactors for the elimination of selected surfactants from municipal wastewaters

Science.gov (United States)

González, Susana; Petrovic, Mira; Barceló, Damiá

2008-07-01

SummaryThe removal of selected surfactants, linear alkylbenzene sulfonates (LAS), coconut diethanol amides (CDEA) and alkylphenol ethoxylates and their degradation products were investigated using a two membrane bioreactor (MBR) with hollow fiber and plate and frame membranes. The two pilot plants MBR run in parallel to a full-scale conventional activated sludge (CAS) treatment. A total of eight influent samples with the corresponding effluent samples were analysed by solid phase extraction-liquid chromatography-tandem mass spectrometry (SPE-LC-MS-MS). The results indicate that both MBR have a better effluent quality in terms of chemical and biological oxygen demand (COD and BOD), NH4+ , concentration and total suspended solids (TSS). MBR showed a better similar performance in the overall elimination of the total nonylphenolic compounds, achieving a 75% of elimination or a 65% (the same elimination reached by CAS). LAS and CDEA showed similar elimination in the three systems investigated and no significant differences were observed.

Anaerobic treatment in Italy

Energy Technology Data Exchange (ETDEWEB)

Del Borghi, M; Solisio, C; Ferrailo, G

1984-02-01

In Italy, environmental protection and energy conservation have become very important since the increase in oil prices. The law requires that all waste waters have a B.O.D. of 40 mg/l by 1986 so there has been an expansion of purification plants since 1976, using anaerobic digestion. The report deals with the current state of anaerobic treatment in Italy with particular reference to (1) animal wastes. In intensive holdings, anaerobic digestion leads to a decrease in pollution and an increase in biogas generation which can be used to cover the energy demand of the process. The factors which influence the builders of digestors for farms are considered. (2) Non toxic industrial wastes. These are the waste waters emanating from the meat packing, brewing, pharmaceutical and chemical industries. Particular reference is made to the distillery plants using anaerobic treatment prior to aerobic digestion. (3) Urban wastes. The advantages and the disadvantages are considered and further research and development is recommended. 20 references.

Using Simulation to Increase Yields in Chemical Engineering

Directory of Open Access Journals (Sweden)

William C. Conley

2003-06-01

Full Text Available Trying to increase the yields or profit or efficiency (less pollution of chemical processes is a central goal of the chemical engineer in theory and practice. Certainly sound training in chemistry, business and pollution control help the engineer to set up optimal chemical processes. However, the ever changing demands of customers and business conditions, plus the multivariate complexity of the chemical business can make optimization challenging. Mathematical tools such as statistics and linear programming have certainly been useful to chemical engineers in their pursuit of optimal efficiency. However, some processes can be modeled linearly and some can not. Therefore, presented here will be an industrial chemical process with potentially five variables affecting the yield. Data from over one hundred runs of the process has been collected, but it is not known initially whether the yield relationship is linear or nonlinear. Therefore, the CTSP multivariate correlation coefficient will be calculated for the data to see if a relationship exists among the variables. Then once it is proven that there is a statistically significant relationship, an appropriate linear or nonlinear equation can be fitted to the data, and it can be optimized for use in the chemical plant.

Exploring Demand Charge Savings from Commercial Solar

Energy Technology Data Exchange (ETDEWEB)

Darghouth, Naim [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Barbose, Galen [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Mills, Andrew [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wiser, Ryan [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gagnon, Pieter [National Renewable Energy Lab. (NREL), Golden, CO (United States); Bird, Lori [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2017-07-31

Commercial retail electricity rates commonly include a demand charge component, based on some measure of the customer’s peak demand. Customer-sited solar PV can potentially reduce demand charges, but the magnitude of these savings can be difficult to predict, given variations in demand charge designs, customer loads, and PV generation profiles. Moreover, depending on the circumstances, demand charges from solar may or may not align well with associated utility cost savings. Lawrence Berkeley National Laboratory (Berkeley Lab) and the National Renewable Energy Laboratory (NREL) are collaborating in a series of studies to understand how solar PV can reduce demand charge levels for a variety of customer types and demand charges designs. Previous work focused on residential customs with solar. This study, instead, focuses on commercial customers and seeks to understand the extent and conditions under which rooftop can solar reduce commercial demand charges. To answer these questions, we simulate demand charge savings for a broad range of commercial customer types, demand charge designs, locations, and PV system characteristics. This particular analysis does not include storage, but a subsequent analysis in this series will evaluate demand charge savings for commercial customers with solar and storage.